The phase-in and phase-out of European emissions of HCFC-141b and HCFC-142b under the Montreal Protocol: Evidence from observations at Mace Head, Ireland and Jungfraujoch, Switzerland from 1994 to 2004

Science.gov (United States)

Derwent, R. G.; Simmonds, P. G.; Greally, B. R.; O'doherty, S.; McCulloch, A.; Manning, A.; Reimann, S.; Folini, D.; Vollmer, M. K.

The mixing ratios of HCFC-141b (1,1-dichlorofluoroethane) and HCFC-142b (1-chloro-1,1-difluoroethane) have been rising steadily in baseline air at Mace Head, Ireland over the 10-year period from 1994 to 2004. These HCFCs are widely used replacements for the chlorofluorocarbons phased out under the Montreal Protocol and its subsequent amendments. Analysis of the HCFC content of regionally-polluted air arriving at Mace Head from the European continent shows that European emissions reached a peak during 2000-2001 and have declined subsequently, following the phase-out in their usage. European emissions of HCFC-141b have been further constrained by observations at the High-Alpine Jungfraujoch site. The reductions are consistent with the phase-out of HCFC production and use from the year 2001 onwards mandated by European regulations designed to exceed the requirements of the Montreal Protocol.

First retrievals of HCFC-142b from ground-based high-resolution FTIR solar observations: application to high-altitude Jungfraujoch spectra

Science.gov (United States)

Mahieu, Emmanuel; O'Doherty, Simon; Reimann, Stefan; Vollmer, Martin; Bader, Whitney; Bovy, Benoît; Lejeune, Bernard; Demoulin, Philippe; Roland, Ginette; Servais, Christian; Zander, Rodolphe

2013-04-01

Hydrofluorocarbons (HCFCs) are the first substitutes to the long-lived ozone depleting halocarbons, in particular the chlorofluorocarbons (CFCs). Given the complete ban of the CFCs by the Montreal Protocol, its Amendments and Adjustments, HCFCs are on the rise, with current rates of increase substantially larger than at the beginning of the 21st century. HCFC-142b (CH3CClF2) is presently the second most abundant HCFCs, after HCFC-22 (CHClF2). It is used in a wide range of applications, including as a blowing foam agent, in refrigeration and air-conditioning. Its concentration will soon reach 25 ppt in the northern hemisphere, with mixing ratios increasing at about 1.1 ppt/yr [Montzka et al., 2011]. The HCFC-142b lifetime is estimated at 18 years. With a global warming potential of 2310 on a 100-yr horizon, this species is also a potent greenhouse gas [Forster et al., 2007]. First space-based retrievals of HCFC-142b have been reported by Dufour et al. [2005]. 17 occultations recorded in 2004 by the Canadian ACE-FTS instrument (Atmospheric Chemistry Experiment - Fourier Transform Spectrometer, onboard SCISAT-1) were analyzed, using two microwindows (1132.5-1135.5 and 1191.5-1195.5 cm-1). In 2009, Rinsland et al. determined the HCFC-142b trend near the tropopause, from the analysis of ACE-FTS observations recorded over the 2004-2008 time period. The spectral region used in this study extended from 903 to 905.5 cm-1. In this contribution, we will present the first HCFC-142b measurements from ground-based high-resolution Fourier Transform Infrared (FTIR) solar spectra. We use observations recorded at the high altitude station of the Jungfraujoch (46.5°N, 8°E, 3580 m asl), with a Bruker 120HR instrument, in the framework of the Network for the Detection of Atmospheric Composition Change (NDACC, visit http://www.ndacc.org). The retrieval of HCFC-142b is very challenging, with simulations indicating only weak absorptions, lower than 1% for low sun spectra and current

Performance of R433A for replacing HCFC22 used in residential air-conditioners and heat pumps

International Nuclear Information System (INIS)

Park, Ki-Jung; Shim, Yun-Bo; Jung, Dongsoo

2008-01-01

In this study, thermodynamic performance of R433A and HCFC22 is measured in a heat pump bench tester under air-conditioning and heat pumping conditions. R433A has no ozone depletion potential and very low greenhouse warming potential of less than 5. R433A also offers a similar vapor pressure to HCFC22 for possible 'drop-in' replacement. Test results showed that the coefficient of performance of R433A is 4.9-7.6% higher than that of HCFC22 while the capacity of R433A is 1.0-5.5% lower than that of HCFC22 for both conditions. The compressor discharge temperature of R433A is 22.6-27.9 deg. C lower than that of HCFC22 while the amount of charge for R433A is 57.0-57.7% lower than that of HCFC22 due to its low density. Overall, R433A is a good long term environmentally friendly alternative to replace HCFC22 in residential air-conditioners and heat pumps due to its excellent thermodynamic and environmental properties with minor adjustments

Release and attenuation of fluorocarbons in landfills

DEFF Research Database (Denmark)

Kjeldsen, Peter; Scheutz, Charlotte

2003-01-01

Several halocarbons with very high global warming and ozone depleting potentials have been used as blowing agent for insulation foam in refrigerators and freezers. Many appliances are shredded after the end of their useful life. Release experiments carried out in the laboratory on insulation foam...... blown with CFC-11, HCFC-141b, HFC- 134a, and HFC-245fa revealed that most of the blowing agent is not released to the atmosphere during a six-week period following the shredding process. The fraction which is released in the six-week period is highly dependent on how fine the foam is shredded....... The residual blowing agent remaining after the six-week period may be very slowly released if the integrity of the foam particles with respect to diffusional properties is kept after disposal of the foam waste in landfills. Laboratory experiments simulating attenuation processes in the landfilled waste...

The disappearance of HCFC 22 and the search for the ideal refrigerant; La disparition du HCFC-22 et le recherche du refrigerant ideal

Energy Technology Data Exchange (ETDEWEB)

Dumas, C. [Ville de Montreal, PQ (Canada). Direction des Immeubles Gestion de l' Energie et du Genie Climatique

2003-03-01

The City of Montreal, Quebec is searching for the optimum refrigerant, and has determined that ammonia, carbon dioxide, hydrocarbons and refrigerant-mixes in the 400 series are to be considered for general refrigeration and in skating rinks in the next years. The refrigerants of the 400 series contribute to the greenhouse effect and it is not possible to utilize them in sunk type systems. The City of Montreal has 12 per cent of ice surfaces in Quebec. The Montreal Protocol, a United Nations document calls for the gradual elimination of the refrigerant monochlorodifluoromethane (HCFC 22) starting in 2004 and that none will be made after 2020 in order to protect the ozone layer. In this document, the author discussed the following topics: (1) supply problems, regulations, international index used to compare refrigeration systems, (2) the origin of refrigerants available on the market and why the chemical industry is incapable of producing the miracle refrigerant, and (3) a proposal for an action plan for the control and the reduction of HCFC 22 leaks, the replacement of entire refrigeration systems and the preparation for the period following the availability of HCFC 22. The author offered twelve conclusions. 10 refs., 9 figs.

Two-phase flow characteristics of HFC and HCFC fluid

International Nuclear Information System (INIS)

Ueno, T.; Matsuda, K.; Kusakabe, T.

1998-01-01

Some two-phase flow characteristics of HFC and HCFC fluid have been investigated experimentally. Fluids used in this experiment are HCFC22 (hereinafter called 'R22'), HCFC123 (hereinafter called 'R123') and Mixture of HFC fluid (hereinafter called 'R407C'). The fluid R407C are mixture of HFC32, HFC134a and HFC125, and their concentrations are 23wt%, 52wt% and 25wt%, respectively. This paper presents main flow parameters such as void fraction, interfacial velocities, bubble diameter distribution and pressure drop multiplier, which can characterize flow behavior. The void fractions and interfacial velocities were measured at some local positions in the single pipe using the bi-optical probe(hereinafter called 'BOP'). The procedure to calculate the void fraction from the void signals obtained by BOP were adopted the so-called slice method. The effects of slice levels on the void fraction were discussed taking into account bubble diameter. The new correlation of slice level as the function of void fraction has been proposed. The area-averaged void fractions obtained from BOP's void signals using new correlation were compared with void fractions obtained from pressure drops. The area-averaged interfacial velocities were also compared with the superficial gas velocities. It was concluded that the accuracy of BOP measurements are 5% for void fraction and less than 8.5% for interfacial velocity

Estimated HCFC-22 emissions for 1990-2050 in China and the increasing contribution to global emissions

Science.gov (United States)

Li, Zhifang; Bie, Pengju; Wang, Ziyuan; Zhang, Zhaoyang; Jiang, Hanyu; Xu, Weiguang; Zhang, Jianbo; Hu, Jianxin

2016-05-01

Chlorodifluoromethane (CHClF2, HCFC-22) is a widely used refrigerant and foaming agent that is not only an ozone-depleting substance (ozone depletion potential (ODP), 0.04) but also a greenhouse gas (global warming potential (GWP), 1780). A comprehensive historical emission inventory for 1990-2014 was produced using a bottom-up method, and a projection through to 2050 was made for China. The results demonstrated that historical emissions increased sharply from 0.2 Gg/yr in 1990 to 127.2 Gg/yr in 2014. Room air-conditioners (RACs), industrial and commercial refrigeration (ICR), and extruded polystyrene (XPS) were three primary emission sources, and accounted for an average of 95.4% of the total emissions over the period studied. The percentage of global HCFC-22 emissions originating from China significantly increased from 0.1% in 1990 to 31.6% in 2012, with an average growth rate of 1.4% per year. Under the Montreal Protocol phasing-out (MPPO) scenario, future emissions were expected to reach a peak of 133.5 Gg/yr in 2016 and then continuously decline to 10.2 Gg/yr in 2050. The accumulative reduction for 2015-2050 would be 5533.8 Gg (equivalent to 221.4 CFC-11-eq Gg and 9850.1 CO2-eq Tg), which is approximately equivalent to the total CO2 emission for China in 2012 (9900 Tg) (Olivier et al., 2013), compared with the no Montreal Protocol scenario (NMP). Under the MPPO scenario, two cases were analyzed to explore the future emission ranges in China. A comparison between the two cases implied that the choice of emission reduction policy will have a considerable impact on HCFC-22 emissions.

Global emissions of refrigerants HCFC-22 and HFC-134a: Unforeseen seasonal contributions

Science.gov (United States)

Xiang, Bin; Montzka, Stephen A.; Miller, Scot M.; Elkins, James W.; Moore, Fred L.; Atlas, Elliot L.; Miller, Ben R.; Weiss, Ray F.; Prinn, Ronald G.; Wofsy, Steven C.

2014-01-01

HCFC-22 (CHClF2) and HFC-134a (CH2FCF3) are two major gases currently used worldwide in domestic and commercial refrigeration and air conditioning. HCFC-22 contributes to stratospheric ozone depletion, and both species are potent greenhouse gases. In this work, we study in situ observations of HCFC-22 and HFC-134a taken from research aircraft over the Pacific Ocean in a 3-y span [HIaper-Pole-to-Pole Observations (HIPPO) 2009–2011] and combine these data with long-term ground observations from global surface sites [National Oceanic and Atmospheric Administration (NOAA) and Advanced Global Atmospheric Gases Experiment (AGAGE) networks]. We find the global annual emissions of HCFC-22 and HFC-134a have increased substantially over the past two decades. Emissions of HFC-134a are consistently higher compared with the United Nations Framework Convention on Climate Change (UNFCCC) inventory since 2000, by 60% more in recent years (2009–2012). Apart from these decadal emission constraints, we also quantify recent seasonal emission patterns showing that summertime emissions of HCFC-22 and HFC-134a are two to three times higher than wintertime emissions. This unforeseen large seasonal variation indicates that unaccounted mechanisms controlling refrigerant gas emissions are missing in the existing inventory estimates. Possible mechanisms enhancing refrigerant losses in summer are (i) higher vapor pressure in the sealed compartment of the system at summer high temperatures and (ii) more frequent use and service of refrigerators and air conditioners in summer months. Our results suggest that engineering (e.g., better temperature/vibration-resistant system sealing and new system design of more compact/efficient components) and regulatory (e.g., reinforcing system service regulations) steps to improve containment of these gases from working devices could effectively reduce their release to the atmosphere. PMID:25422438

HCFC-142b emissions in China: An inventory for 2000 to 2050 basing on bottom-up and top-down methods

Science.gov (United States)

Han, Jiarui; Li, Li; Su, Shenshen; Hu, Jianxin; Wu, Jing; Wu, Yusheng; Fang, Xuekun

2014-05-01

1-Chloro-1,1-difluoroethane (HCFC-142b) is both ozone depleting substance included in the Montreal Protocol on Substances that Deplete the Ozone Layer (Montreal Protocol) and potent greenhouse gas with high global warming potential. As one of the major HCFC-142b consumption and production countries in the world, China's control action will contribute to both mitigating climate change and protecting ozone layer. Estimating China's HCFC-142b emission is a crucial step for understanding its emission status, drawing up phasing-out plan and evaluating mitigation effect. Both the bottom-up and top-down method were adopted in this research to estimate HCFC-142b emissions from China. Results basing on different methods were compared to test the effectiveness of two methods and validate inventory's reliability. Firstly, a national bottom-up emission inventory of HCFC-142b for China during 2000-2012 was established based on the 2006 IPCC Guidelines for National Greenhouse Gas Inventories and the Montreal Protocol, showing that in contrast to the downward trend revealed by existing results, HCFC-142b emissions kept increasing from 0.1 kt/yr in 2000 to the peak of 14.4 kt/yr in 2012. Meanwhile a top-down emission estimation was also developed using interspecies correlation method. By correlating atmospheric mixing ratio data of HCFC-142b and reference substance HCFC-22 sampled from four representative cities (Beijing, Hangzhou, Lanzhou and Guangzhou, for northern, eastern, western and southern China, respectively), China's HCFC-142b emission in 2012 was calculated. It was 16.24(13.90-18.58) kt, equivalent to 1.06 kt ODP and 37 Tg CO2-eq, taking up 9.78% (ODP) of total HCFCs emission in China or 30.5% of global HCFC-142b emission. This result was 12.7% higher than that in bottom-up inventory. Possible explanations were discussed. The consistency of two results lend credit to methods effectiveness and results reliability. Finally, future HCFC-142b emission was projected to 2050

New High-Resolution Absorption Cross-Section Measurements of HCFC-142B in the Mid-Ir

Science.gov (United States)

Le Bris, Karine; Strong, Kimberly; Melo, Stella

2009-06-01

HCFC-142b (1-chloro-1,1-difluoroethane) is a temporary substitute for ozone-depleting chlorofluorocarbons (CFCs). However, due to its high absorption cross-sections in the mid-IR, HCFC-142b is also a highly potent greenhouse gas, now detectable from space by satellite missions. So far, the accuracy of the retrieval has been limited by the lack of reference data in a range of temperatures compatible with atmospheric observations. We present new absorption cross section measurements of HCFC-142b at high-resolution (0.02 cm^{-1}) from 223 K to 283 K in the 600 cm^{-1}- 4000 cm^{-1} spectral window. The composite spectra are calculated for each temperature from a set of acquisitions at different pressures by Fourier transform spectroscopy.

Measurements of HFC-134a and HCFC-22 in groundwater and unsaturated-zone air: implications for HFCs and HCFCs as dating tracers

Science.gov (United States)

Haase, Karl B.; Busenberg, Eurybiades; Plummer, Niel; Casile, Gerolamo; Sanford, Ward E.

2014-01-01

A new analytical method using gas chromatography with an atomic emission detector (GC–AED) was developed for measurement of ambient concentrations of hydrochlorofluorocarbons (HCFCs) and hydrofluorocarbons (HFCs) in soil, air, and groundwater, with the goal of determining their utility as groundwater age tracers. The analytical detection limits of HCFC-22 (difluorochloromethane, CHClF2) and HFC-134a (1,2,2,2-tetrafluoroethane, C2H2F4) in 1 L groundwater samples are 4.3 × 10− 1 and 2.1 × 10− 1 pmol kg− 1, respectively, corresponding to equilibrium gas-phase mixing ratios of approximately 5–6 parts per trillion by volume (pptv). Under optimal conditions, post-1960 (HCFC-22) and post-1995 (HFC-134a) recharge could be identified using these tracers in stable, unmixed groundwater samples. Ambient concentrations of HCFC-22 and HFC-134a were measured in 50 groundwater samples from 27 locations in northern and western parts of Virginia, Tennessee, and North Carolina (USA), and 3 unsaturated-zone profiles were collected in northern Virginia. Mixing ratios of both HCFC-22 and HFC-134a decrease with depth in unsaturated-zone gas profiles with an accompanying increase in CO2 and loss of O2. Apparently, ambient concentrations of HCFC-22 and HFC-134a are readily consumed by methanotrophic bacteria under aerobic conditions in the unsaturated zone. The results of this study indicate that soils are a sink for these two greenhouse gases. These observations contradict the previously reported results from microcosm experiments that found that degradation was limited above-ambient HFC-134a. The groundwater HFC and HCFC concentrations were compared with concentrations of chlorofluorocarbons (CFCs, CFC-11, CFC-12, CFC-113) and sulfur hexafluoride (SF6). Nearly all samples had measured HCFC-22 or HFC-134a that were below concentrations predicted by the CFCs and SF6, with many samples showing a complete loss of HCFC-22 and HFC-134a. This study indicates that HCFC-22 and HFC-134

Replacement of Hydrochlorofluorocarbon (HCFC) -225 Solvent for Cleaning and Verification Sampling of NASA Propulsion Oxygen Systems Hardware, Ground Support Equipment, and Associated Test Systems

Science.gov (United States)

Mitchell, Mark A.; Lowrey, Nikki M.

2015-01-01

Since the 1990's, when the Class I Ozone Depleting Substance (ODS) chlorofluorocarbon-113 (CFC-113) was banned, NASA's rocket propulsion test facilities at Marshall Space Flight Center (MSFC) and Stennis Space Center (SSC) have relied upon hydrochlorofluorocarbon-225 (HCFC-225) to safely clean and verify the cleanliness of large scale propulsion oxygen systems. Effective January 1, 2015, the production, import, export, and new use of HCFC-225, a Class II ODS, was prohibited by the Clean Air Act. In 2012 through 2014, leveraging resources from both the NASA Rocket Propulsion Test Program and the Defense Logistics Agency - Aviation Hazardous Minimization and Green Products Branch, test labs at MSFC, SSC, and Johnson Space Center's White Sands Test Facility (WSTF) collaborated to seek out, test, and qualify a replacement for HCFC-225 that is both an effective cleaner and safe for use with oxygen systems. Candidate solvents were selected and a test plan was developed following the guidelines of ASTM G127, Standard Guide for the Selection of Cleaning Agents for Oxygen Systems. Solvents were evaluated for materials compatibility, oxygen compatibility, cleaning effectiveness, and suitability for use in cleanliness verification and field cleaning operations. Two solvents were determined to be acceptable for cleaning oxygen systems and one was chosen for implementation at NASA's rocket propulsion test facilities. The test program and results are summarized. This project also demonstrated the benefits of cross-agency collaboration in a time of limited resources.

Global HCFC-22 measurements with MIPAS: retrieval, validation, global distribution and its evolution over 2005–2012

Directory of Open Access Journals (Sweden)

M. Chirkov

2016-03-01

Full Text Available We report on HCFC-22 data acquired by the Michelson Interferometer for Passive Atmospheric Sounding (MIPAS in the reduced spectral resolution nominal observation mode. The data cover the period from January 2005 to April 2012 and the altitude range from the upper troposphere (above cloud top altitude to about 50 km. The profile retrieval was performed by constrained nonlinear least squares fitting of modelled spectra to the measured limb spectral radiances. The spectral ν4-band at 816.5 ± 13 cm−1 was used for the retrieval. A Tikhonov-type smoothing constraint was applied to stabilise the retrieval. In the lower stratosphere, we find a global volume mixing ratio of HCFC-22 of about 185 pptv in January 2005. The rate of linear growth in the lower latitudes lower stratosphere was about 6 to 7 pptv year−1 in the period 2005–2012. The profiles obtained were compared with ACE-FTS satellite data v3.5, as well as with MkIV balloon profiles and cryosampler balloon measurements. Between 13 and 22 km, average agreement within −3 to +5 pptv (MIPAS – ACE with ACE-FTS v3.5 profiles is demonstrated. Agreement with MkIV solar occultation balloon-borne measurements is within 10–20 pptv below 30 km and worse above, while in situ cryosampler balloon measurements are systematically lower over their full altitude range by 15–50 pptv below 24 km and less than 10 pptv above 28 km. MIPAS HCFC-22 time series below 10 km altitude are shown to agree mostly well to corresponding time series of near-surface abundances from the NOAA/ESRL and AGAGE networks, although a more pronounced seasonal cycle is obvious in the satellite data. This is attributed to tropopause altitude fluctuations and subsidence of polar winter stratospheric air into the troposphere. A parametric model consisting of constant, linear, quasi-biennial oscillation (QBO and several sine and cosine terms with different periods has been fitted to the temporal variation of stratospheric

Photodegradation of HCFC-22 Using Microwave Discharge Electrodeless Mercury Lamp with TiO2 Photocatalyst Balls

Directory of Open Access Journals (Sweden)

Seong-Gyu Seo

2014-01-01

Full Text Available The photodegradation of chlorodifluoromethane (HCFC-22 was investigated using microwave/UV/TiO2 photocatalysts hybrid system. The microwave discharge electrodeless mercury lamp (MDEML used in this study showed mainly atomic Hg emission lines at 253.7 nm. The decomposition efficiency of HCFC-22 increased with decreasing inlet concentration and with increasing reactor residence time. The removal efficiency increased with increasing microwave power on every oxygen concentration. The highest degradation efficiency was obtained when both TiO2 balls and MDEML were used.

Preparation and characterization of coating sodium trisilicate (Na2O.nSiO2) at calcium carbonate (CaCO3) for blowing agent in Mg alloy foam

Science.gov (United States)

Erryani, Aprilia; Lestari, Franciska Pramuji; Annur, Dhyah; Kartika, Ika

2018-05-01

The role of blowing agent in the manufacture of porous metal alloys is very important to produce the desired pore. The thermal stability and speed of foam formation have an effect on the resulting pore structure. In porous metal alloys, uniformity of size and pore deployment are the main determinants of the resulting alloys. The coating process of calcium carbonate (CaCO3) has been done using Sodium trisilicate solution by sol-gel method. Foaming agent was pretreated by coating SiO2 passive layer on the surface of CaCO3. This coating aims to produce a more stable blowing agent so that the foaming process can produce a more uniform pore size. The microstructure of the SiO2 passive was observed using Scanning Electron Microscope (SEM) equipped by Energy Dispersive X-Ray Spectrometer (EDS) mapping. The results showed coating CaCO3 using sodium trisilicate was successfully done creating a passive layer of SiO2 on the surface of CaCO3. By the coating process, the thermal stability of coated CaCO3 increased compared to uncoated CaCO3.

Performance of a split-type air conditioner matched with coiled adiabatic capillary tubes using HCFC22 and HC290

International Nuclear Information System (INIS)

Zhou, Guobing; Zhang, Yufeng

2010-01-01

This paper experimentally investigated the system performance of a split-type air conditioner matching with different coiled adiabatic capillary tubes for HCFC22 and HC290. Experiments were carried out in a room-type calorimeter. The results have shown that (1) similar cooling effects can be achieved by matching various capillary tubes of different inner diameters; (2) parallel capillary tubes presented better system performance and flow stability with weaker inlet pressure fluctuations than the single capillary tube; (3) with the coil diameter of the capillary tube increasing from 40 mm to 120 mm, the mass flow rate tended to increase slightly. But the cooling capacity, input power and energy efficiency ratio (EER) did not show evident tendency of change; (4) the refrigerant charge and mass flow rate for HC290 were only 44% and 47% of that for HCFC22, respectively, due to the much lower density. And HC290 had 4.7-6.7% lower cooling capacity and 12.1-12.3% lower input power with respect to HCFC22. However, the EER of HC290 can be 8.5% higher than that of HCFC22, which exhibits the advantage of using HC290. In addition, the experimental uncertainties were analyzed and some application concerns of HC290 were discussed.

Thar she blows! A novel method for DNA collection from cetacean blow.

Directory of Open Access Journals (Sweden)

Céline H Frère

Full Text Available BACKGROUND: Molecular tools are now widely used to address crucial management and conservation questions. To date, dart biopsying has been the most commonly used method for collecting genetic data from cetaceans; however, this method has some drawbacks. Dart biopsying is considered inappropriate for young animals and has recently come under scrutiny from ethical boards, conservationists, and the general public. Thus, identifying alternative genetic collection techniques for cetaceans remains a priority, especially for internationally protected species. METHODOLOGY/PRINCIPAL FINDINGS: In this study, we investigated whether blow-sampling, which involves collecting exhalations from the blowholes of cetaceans, could be developed as a new less invasive method for DNA collection. Our current methodology was developed using six bottlenose dolphins, Tursiops truncatus, housed at the National Aquarium, Baltimore (USA, from which we were able to collect both blow and blood samples. For all six individuals, we found that their mitochondrial and microsatellite DNA profile taken from blow, matched their corresponding mitochondrial and microsatellite DNA profile collected from blood. This indicates that blow-sampling is a viable alternative method for DNA collection. CONCLUSION/SIGNIFICANCE: In this study, we show that blow-sampling provides a viable and less invasive method for collection of genetic data, even for small cetaceans. In contrast to dart biopsying, the advantage of this method is that it capitalizes on the natural breathing behaviour of dolphins and can be applied to even very young dolphins. Both biopsy and blow-sampling require close proximity of the boat, but blow-sampling can be achieved when dolphins voluntarily bow-ride and involves no harmful contact.

Effect of mass concentration of composite phase change material CA-DE on HCFC-141b hydrate induction time and system stability

Science.gov (United States)

Li, Juan; Sun, Zhigao; Liu, Chenggang; Zhu, Minggui

2018-03-01

HCFC-141b hydrate is a new type of environment-friendly cold storage medium which may be adopted to balance energy supply and demand, achieve peak load shifting and energy saving, wherein the hydrate induction time and system stability are key factors to promote and realize its application in industrial practice. Based on step cooling curve measurement, two kinds of aliphatic hydrocarbon organics, n-capric acid (CA) and lauryl alcohol (DE), were selected to form composite phase change material and to promote the generation of HCFC-141b hydrate. Five kinds of CA-DE mass concentration were chosen to compare the induction time and hydration system stability. In order to accelerate temperature reduction rate, the metal Cu with high heat conductivity performance was adopted to conduct out the heat generated during phase change. Instability index was introduced to appraise system stability. Experimental results show that phase change temperature and sub-cooling degree of CA-DE is 11.1°C and 3.0°C respectively, which means it is a preferable medium for HCFC-141b hydrate formation. For the experimental hydration systems, segmented emulsification is achieved by special titration manner to avoid rapid layering under static condition. Induction time can achieve up to 23.3min with the densest HCFC-141b hydrate and the lowest instability index, wherein CA-DE mass concentration is 3%.

Blowing Flap Experiment: PIV Measurements

Science.gov (United States)

Hutcheson, Florence V.; Stead, Daniel J.; Bremmer, David M.

2004-01-01

PIV measurements of the flow in the region of a flap side edge are presented for several flap configurations. The test model is a NACA 63(sub 2)-215 Hicks Mod-B main element airfoil with a half-span Fowler flap. Air is blown from small slots located along the flap side edge on either the top, bottom or side surfaces. The test set up is described and flow measurements for a baseline and three blowing flap configurations are presented. The effects that the flap tip jets have on the structure of the flap side edge flow are discussed for each of the flap configurations tested. The results indicate that blowing air from a slot located along the top surface of the flap greatly weakened the top vortex system and pushed it further off the top surface. Blowing from the bottom flap surface kept the strong side vortex further outboard while blowing from the side surface only strengthened the flap vortex system. It is concluded that blowing from the top or bottom surfaces of the flap may lead to a reduction of flap side edge noise.

Simulated and experimental performance of split packaged air conditioner using refrigerant HC-290 as a substitute for HCFC-22

International Nuclear Information System (INIS)

Padalkar, Atul S.; Mali, Kundlik V.; Devotta, Sukumar

2014-01-01

This paper discusses the use of propane (HC-290) as a safe and energy efficient alternative to HCFC-22 in a typical split air conditioner with nominal cooling capacities up to 5.1 kW. Initially split air conditioner performance is simulated for cooling capacity, energy efficiency ratio (EER), and refrigerant charge. Tests were conducted for different test cases in a psychrometric test chamber with HCFC-22 and HC-290. The test conditions considered are as per Indian Standards, IS 1391 (1992) Part I. The various parameters considered were based on simulated performance with the objective to achieve maximum EER for the desired cooling capacity. As the flammability is an issue for HC-290, the reduction of HC-290 charge was another objective. Two different types of condensers, first with smaller size tubing and another parallel flow condenser (PFC) or minichannel condenser were used in order to reduce HC-290 charge. For HC-290, the highest EER achieved was 3.7 for cooling capacity 4.90 kW for a refrigerant charge of 360 g. The important safety aspects of using HC-290 in air conditioner are discussed. The refrigerant charge as per EN 378 for different cooling capacities and room sizes is also considered. -- Highlights: • Simulation for performance of split air conditioner has been done using HC-290 as a replacement to HCFC-22. • The safety aspects of HC-290 are discussed when used in split air conditioner. • HC-290 was tested in psychrometric test chamber as per IS 1391 part 1. • With PFC, HC-290 gave highest EER of 3.7 which was 37% higher than that of HCFC-22. • The lowest HC-290 charge used in test was 340 g which is well below LFL

The thermal conductivity of 1-chloro-1,1-difluoroethane (HCFC-142b)

Science.gov (United States)

Sousa, A. T.; Fialho, P. S.; Nieto de Castro, C. A.; Tufeu, R.; Le Neindre, B.

1992-05-01

The thermal conductivity of 1-chloro-1,1-difluoroethane (HCFC-142b) has been measured in the temperature range 290 to 504 K and pressures up to 20 MPa with a concentric-cylinder apparatus operating in a steady-state mode. These temperature and pressure ranges cover all fluid states. The estimated accuracy of the method is about 2%. The density dependence of the thermal conductivity has been studied in the liquid region.

PIV Measurements on a Blowing Flap

Science.gov (United States)

Hutcheson, Florence V.; Stead, Daniel J.

2004-01-01

PIV measurements of the flow in the region of a flap side edge are presented for several blowing flap configurations. The test model is a NACA 63(sub 2)-215 Hicks Mod-B main-element airfoil with a half-span Fowler flap. Air is blown from small slots located along the flap side edge on either the top, bottom or side surfaces. The test set up is described and flow measurements for a baseline and three blowing flap configurations are presented. The effects that the flap tip jets have on the structure of the flap side edge flow are discussed for each of the flap configurations tested. The results indicate that blowing air from a slot located along the top surface of the flap greatly weakened the top vortex system and pushed it further off the top surface. Blowing from the bottom flap surface kept the strong side vortex further outboard while blowing from the side surface only strengthened the vortex system or accelerated the merging of the side vortex to the flap top surface. It is concluded that blowing from the top or bottom surfaces of the flap may lead to a reduction of flap side edge noise.

Substituting HCFC-22 for HFC-410A: an environmental impact trade-off between the ozone depletion and climate change regimes

Science.gov (United States)

Wang, Z.; Fang, X.; Zhang, J.

2015-12-01

After the phase-out of hydrochlorofluorocarbons (HCFCs) as ozone-depleting substances pursuant to the requirements of the Montreal Protocol, hydrofluorocarbons (HFCs) are worldwide used as substitutes although the bulk of them are potent greenhouse gases (GHGs). Therefore, the alternation may bring side effect on global climate change. The trade-off of its environmental impacts between the ozone depletion and climate change regimes necessitates a quantification of the past and future consumption and emissions of both the original HCFCs and their alternative HFCs. Now a dilemma arise in China's RAC industry that HCFC-22, which has an ozone-depleting potential (ODP) of 0.055, has been replaced by HFC-410A, which is a blended potent GHG from respective 50% HFC-32 and HFC-125 with a global warming potential (GWP) of 1923.5. Here, we present our results of estimates of consumption and emissions of HCFC-22 and HFC-410A from 1994 to 2050. Historic emissions of HCFC-22 contributed to global total HCFCs by 4.0% (3.0%-5.6%) ODP-weighted. Projection under a baseline scenario shows future accumulative emissions of HFC-410A make up 5.9%-11.0% of global GWP-weighted HFCs emissions, and its annual contribution to national overall CO2 emissions can be 5.5% in 2050. This makes HCFC-22 and HFC-410A emissions of significant importance in ozone depletion and climate change regimes. Two mitigation scenarios were set to assess the mitigation performance under the North America Proposal and an accelerated schedule. In practice of international environmental agreement, "alternative to alternative" should be developed to avoid regrettable alternations.

Mechanistic insights aid the search for CFC substitutes: risk assessment of HCFC-123 as an example.

Science.gov (United States)

Jarabek, A M; Fisher, J W; Rubenstein, R; Lipscomb, J C; Williams, R J; Vinegar, A; McDougal, J N

1994-06-01

An international consensus on the need to reduce the use of chlorofluorocarbons (CFCs) and other ozone-depleting gases such as the halons led to the adoptions of the 1987 Montreal Protocol and Title VI of the 1990 Clean Air Act Amendments, "Protecting Stratospheric Ozone." These agreements included major provisions for reducing and eventually phasing out production and use of CFCs and halons as well as advancing the development of replacement chemicals. Because of the ubiquitous use and benefits of CFCs and halons, an expeditious search for safe replacements to meet the legislative deadlines is of critical importance. Toxicity testing and health risk assessment programs were established to evaluate the health and environmental impact of these replacement chemicals. Development and implementation of these programs as well as the structural-activity relationships significant for the development of the replacement chemicals are described below. A dose-response evaluation for the health risk assessment of the replacement chemical HCFC-123 (2,2-dichloro-1,1,1-trifluoroethane) is also presented to show an innovative use of physiologically based pharmacokinetic (PBPK) modeling. This is based on a parallelogram approach using data on the anesthetic gas halothane, a structural analog to HCFC-123. Halothane and HCFC-123 both form the same metabolite, trifluoroacetic acid (TFA), indicative of the same metabolic oxidative pathway attributed to hepatotoxicity. The parallelogram approach demonstrates the application of template model structures and shows how PBPK modeling, together with judicious experimental design, can be used to improve the accuracy of health risk assessment and to decrease the need for extensive laboratory animal testing.

Calculated trends and the atmospheric abundance of 1,1,1,2-tetrafluoroethane, 1,1-dichloro-1-fluoroethane, and 1-chloro-1,1-difluoroethane using automated in-situ gas chromatography-mass spectrometry measurements recorded at Mace Head, Ireland, from October 1994 to March 1997

Science.gov (United States)

Simmonds, P. G.; O'Doherty, S.; Huang, J.; Prinn, R.; Derwent, R. G.; Ryall, D.; Nickless, G.; Cunnold, D.

1998-01-01

The first in-situ measurements by automated gas chromatograph-mass spectrometer are reported for 1,1,1,2-tetrafluoroethane (HFC-134a), 1,1-dichloro-1-fluoroethane, (HCFC-141b), and 1-chloro-1,1-difluoroethane, (HCFC-142b). These compounds are steadily replacing the chlorofluorocarbons (CFCs) as refrigerants, foam-blowing agents, and solvents. The concentrations of all three compounds are shown to be rapidly increasing in the atmosphere, with 134a increasing at a rate of 2.05±0.02 ppt yr-1 over the 30 months of observations. Similarly, 141b and 142b increased at rates of 2.49±0.03 and 1.24±0.02 ppt yr-1, respectively, over the same period. The concentrations recorded at the atmospheric research station at Mace Head, Ireland, on January 1, 1996, the midpoint of the time series, were 3.67 ppt (134a), 7.38 ppt (141b), and 8.78 ppt (142b). From these observations we optimally estimate the HCFC and HFC emissions using a 12-box global model and OH concentrations derived from global 1,1,1-trichloroethane (CCl3CH3) measurements. Comparing two methods of estimating emissions with independent industry estimates shows satisfactory agreement for 134a and 141b, while for 142b, industry estimates are less than half those required to explain our observations.

CFC-11, CFC-12 and HCFC-22 ground-based remote sensing FTIR measurements at Réunion Island and comparisons with MIPAS/ENVISAT data

Directory of Open Access Journals (Sweden)

M. Zhou

2016-11-01

Full Text Available Profiles of CFC-11 (CCl3F, CFC-12 (CCl2F2 and HCFC-22 (CHF2Cl have been obtained from Fourier transform infrared (FTIR solar absorption measurements above the Saint-Denis (St Denis and Maïdo sites at Réunion Island (21° S, 55° E with low vertical resolution. FTIR profile retrievals are performed by the well-established SFIT4 program and the detail retrieval strategies along with the systematic/random uncertainties of CFC-11, CFC-12 and HCFC-22 are discussed in this study. The FTIR data of all three species are sensitive to the whole troposphere and the lowermost stratosphere, with the peak sensitivity between 5 and 10 km. The ground-based FTIR data have been compared with the collocated Michelson Interferometer for Passive Atmospheric Sounding (MIPAS/ENVISAT data and found to be in good agreement: the observed mean relative biases and standard deviations of the differences between the smoothed MIPAS and FTIR partial columns (6–30 km are (−4.3 and 4.4 %, (−2.9 and 4.6 % and (−0.7 and 4.8 % for CFC-11, CFC-12 and HCFC-22, respectively, which are within the combined error budgets from both measurements. The season cycles of CFC-11, CFC-12 and HCFC-22 from FTIR measurements and MIPAS data show a similar variation: concentration is highest in February–April and lowest in August–October. The trends derived from the combined St Denis and Maïdo FTIR time series are −0.86 ± 0.12 and 2.84 ± 0.06 % year−1 for CFC-11 and HCFC-22, respectively, for the period 2004 to 2016, and −0.76 ± 0.05 % year−1 for CFC-12 for 2009 to 2016. These measurements are consistent with the trends observed by the National Oceanic and Atmospheric Administration (NOAA Global Monitoring Division's (GMD Halocarbons & other Atmospheric Trace Species Group (HATS measurements at Samoa (14.2° S, 170.5° W for CFC-11 (−0.87 ± 0.04 % year−1, but slightly weaker for HCFC-22 (3.46 ± 0.05 % year−1 and

Citric acid as multifunctional agent in blowing films of starch/PBAT

Directory of Open Access Journals (Sweden)

Patrícia Salomão Garcia

2011-09-01

Full Text Available Citric acid was used as a compatibilizer in the production of starch and PBAT films plasticized with glycerol and processed by blow extrusion. Films produced were characterized by WVP, mechanical properties, FT-IR-ATR and SEM. WPV ranged from 3.71 to 12.73×10-11 g m-1 s-1 Pa-1, while tensile strength and elongation at break ranged from 1.81 to 7.15 MPa and from 8.61 to 23.63%, respectively. Increasing the citric acid concentration improved WVP and slightly decreased film resistance and elongation. The films micrographs revealed a more homogeneous material with the addition of citric acid. However, the infrared spectra revealed little about cross-linking esterification reaction

Heterotic Mini-landscape in blow-up

CERN Document Server

Bizet, Nana Geraldine Cabo

2013-01-01

Localization properties of fields in compact extra dimensions are crucial ingredients for string model building, particularly in the framework of orbifold compactifications. Realistic models often require a slight deviation from the orbifold point, that can be analyzed using field theoretic methods considering (singlet) fields with nontrivial vacuum expectation values. Some of these fields correspond to blow-up modes that represent the resolution of orbifold singularities. Improving on previous analyses we give here an explicit example of the blow-up of a model from the heterotic Mini-landscape. An exact identification of the blow-up modes at various fixed points and fixed tori with orbifold twisted fields is given. We match the massless spectra and identify the blow-up modes as non-universal axions of compactified string theory. We stress the important role of the Green-Schwarz anomaly polynomial for the description of the resolution of orbifold singularities.

Investigation of Airfoil Aeroacoustics with Blowing Control Mechanism

Directory of Open Access Journals (Sweden)

Baha ZAFER

2016-11-01

Full Text Available In this investigation, it is dealt with computational aero-acoustic analysis of an airfoil with jet blowing. The airfoil shape is selected as NACA0015 profile with jet blowing on upper surface. The calculations of analysis are done by using commercial finite volume solver. The k-ε turbulence model is used for the turbulence modeling and the Ffowcs Williams and Hawking acoustic analogy model is run for determination of acoustic data. The numerical results are compared with experimental data for computed Sound Pressure Level without jet blowing and well agreement is observed. In the case of jet blowing, the effects of different jet angle, velocity ratio and angle of attack on airfoil are investigated and noise levels of non jet cases and jet blowing cases are studied.

Whistle-blowing

International Nuclear Information System (INIS)

Fitzgerald, K.

1990-01-01

In this paper five engineers in nuclear power, aerospace, and air-traffic control recount their experiences in following their consciences. Exposing errors or unethical conduct in any occupation is risky, but when engineering judgement is involved, the risks of blowing the whistle acquire an added dimension. A technical decision cannot always be categorized as strictly right or wrong - unlike situations in which an organization is falsifying documents or overcharging for a product. Consequently, the engineer must be convinced of being right and then wait, sometimes years and even decades after lives are lost or millions of dollars are spent, to be proved right or wrong. Frequently, the whistle-blower's career is destroyed in the meantime. In the following cases, which date from the 1970s and 1980s, the whistle-blowers have by now been vindicated to a degree for their actions, though the verdict may not be unanimous. And the careers of the first group may have even benefitted by blowing the whistle

Blow-up: A Free Lunch?

Directory of Open Access Journals (Sweden)

Jan Koenderink

2012-02-01

Full Text Available We consider operations that change the size of images, either shrinks or blow-ups. Image processing offers numerous possibilities, put at everyone's disposal with such computer programs as Adobe Photoshop. We consider a different class of operations, aimed at immediate visual awareness, rather than pixel arrays. We demonstrate cases of blow-ups that do not sacrifice apparent resolution. This apparent information gain is due to “amodal occlusion.”

Recent increases in the atmospheric growth rate and emissions of HFC-23 (CHF3) and the link to HCFC-22 (CHClF2) production

Science.gov (United States)

Simmonds, Peter G.; Rigby, Matthew; McCulloch, Archie; Vollmer, Martin K.; Henne, Stephan; Mühle, Jens; O'Doherty, Simon; Manning, Alistair J.; Krummel, Paul B.; Fraser, Paul J.; Young, Dickon; Weiss, Ray F.; Salameh, Peter K.; Harth, Christina M.; Reimann, Stefan; Trudinger, Cathy M.; Steele, L. Paul; Wang, Ray H. J.; Ivy, Diane J.; Prinn, Ronald G.; Mitrevski, Blagoj; Etheridge, David M.

2018-03-01

High frequency measurements of trifluoromethane (HFC-23, CHF3), a potent hydrofluorocarbon greenhouse gas, largely emitted to the atmosphere as a by-product of the production of the hydrochlorofluorocarbon HCFC-22 (CHClF2), at five core stations of the Advanced Global Atmospheric Gases Experiment (AGAGE) network, combined with measurements on firn air, old Northern Hemisphere air samples and Cape Grim Air Archive (CGAA) air samples, are used to explore the current and historic changes in the atmospheric abundance of HFC-23. These measurements are used in combination with the AGAGE 2-D atmospheric 12-box model and a Bayesian inversion methodology to determine model atmospheric mole fractions and the history of global HFC-23 emissions. The global modelled annual mole fraction of HFC-23 in the background atmosphere was 28.9 ± 0.6 pmol mol-1 at the end of 2016, representing a 28 % increase from 22.6 ± 0.4 pmol mol-1 in 2009. Over the same time frame, the modelled mole fraction of HCFC-22 increased by 19 % from 199 ± 2 to 237 ± 2 pmol mol-1. However, unlike HFC-23, the annual average HCFC-22 growth rate slowed from 2009 to 2016 at an annual average rate of -0.5 pmol mol-1 yr-2. This slowing atmospheric growth is consistent with HCFC-22 moving from dispersive (high fractional emissions) to feedstock (low fractional emissions) uses, with HFC-23 emissions remaining as a consequence of incomplete mitigation from all HCFC-22 production.Our results demonstrate that, following a minimum in HFC-23 global emissions in 2009 of 9.6 ± 0.6, emissions increased to a maximum in 2014 of 14.5 ± 0.6 Gg yr-1 and then declined to 12.7 ± 0.6 Gg yr-1 (157 Mt CO2 eq. yr-1) in 2016. The 2009 emissions minimum is consistent with estimates based on national reports and is likely a response to the implementation of the Clean Development Mechanism (CDM) to mitigate HFC-23 emissions by incineration in developing (non-Annex 1) countries under the Kyoto Protocol. Our derived cumulative

Use of cooling tower blow down in ethanol fermentation.

Science.gov (United States)

Rajagopalan, N; Singh, V; Panno, B; Wilcoxon, M

2010-01-01

Reducing water consumption in bioethanol production conserves an increasingly scarce natural resource, lowers production costs, and minimizes effluent management issues. The suitability of cooling tower blow down water for reuse in fermentation was investigated as a means to lower water consumption. Extensive chemical characterization of the blow down water revealed low concentrations of toxic elements and total dissolved solids. Fermentation carried out with cooling tower blow down water resulted in similar levels of ethanol and residual glucose as a control study using deionized water. The study noted good tolerance by yeast to the specific scale and corrosion inhibitors found in the cooling tower blow down water. This research indicates that, under appropriate conditions, reuse of blow down water from cooling towers in fermentation is feasible.

Holes at High Blowing Ratios

Directory of Open Access Journals (Sweden)

Phillip M. Ligrani

1996-01-01

Full Text Available Experimental results are presented which describe the development and structure of flow downstream of a single row of holes with compound angle orientations producing film cooling at high blowing ratios. This film cooling configuration is important because similar arrangements are frequently employed on the first stage of rotating blades of operating gas turbine engines. With this configuration, holes are spaced 6d apart in the spanwise direction, with inclination angles of 24 degrees, and angles of orientation of 50.5 degrees. Blowing ratios range from 1.5 to 4.0 and the ratio of injectant to freestream density is near 1.0. Results show that spanwise averaged adiabatic effectiveness, spanwise-averaged iso-energetic Stanton number ratios, surveys of streamwise mean velocity, and surveys of injectant distributions change by important amounts as the blowing ratio increases. This is due to injectant lift-off from the test surface just downstream of the holes.

Recent increases in the atmospheric growth rate and emissions of HFC-23 (CHF3 and the link to HCFC-22 (CHClF2 production

Directory of Open Access Journals (Sweden)

P. G. Simmonds

2018-03-01

Full Text Available High frequency measurements of trifluoromethane (HFC-23, CHF3, a potent hydrofluorocarbon greenhouse gas, largely emitted to the atmosphere as a by-product of the production of the hydrochlorofluorocarbon HCFC-22 (CHClF2, at five core stations of the Advanced Global Atmospheric Gases Experiment (AGAGE network, combined with measurements on firn air, old Northern Hemisphere air samples and Cape Grim Air Archive (CGAA air samples, are used to explore the current and historic changes in the atmospheric abundance of HFC-23. These measurements are used in combination with the AGAGE 2-D atmospheric 12-box model and a Bayesian inversion methodology to determine model atmospheric mole fractions and the history of global HFC-23 emissions. The global modelled annual mole fraction of HFC-23 in the background atmosphere was 28.9 ± 0.6 pmol mol−1 at the end of 2016, representing a 28 % increase from 22.6 ± 0.4 pmol mol−1 in 2009. Over the same time frame, the modelled mole fraction of HCFC-22 increased by 19 % from 199 ± 2 to 237 ± 2 pmol mol−1. However, unlike HFC-23, the annual average HCFC-22 growth rate slowed from 2009 to 2016 at an annual average rate of −0.5 pmol mol−1 yr−2. This slowing atmospheric growth is consistent with HCFC-22 moving from dispersive (high fractional emissions to feedstock (low fractional emissions uses, with HFC-23 emissions remaining as a consequence of incomplete mitigation from all HCFC-22 production.Our results demonstrate that, following a minimum in HFC-23 global emissions in 2009 of 9.6 ± 0.6, emissions increased to a maximum in 2014 of 14.5 ± 0.6 Gg yr−1 and then declined to 12.7 ± 0.6 Gg yr−1 (157 Mt CO2 eq. yr−1 in 2016. The 2009 emissions minimum is consistent with estimates based on national reports and is likely a response to the implementation of the Clean Development Mechanism (CDM to mitigate HFC-23 emissions by

Numerical study of blow-up in the Davey-Stewartson system

KAUST Repository

Klein, Christian

2013-03-01

Nonlinear dispersive partial differential equations such as the nonlinear Schrödinger equations can have solutions that blow up. We numerically study the long time behavior and potential blow-up of solutions to the focusing Davey-Stewartson II equation by analyzing perturbations of the lump and the Ozawa solutions. It is shown in this way that both are unstable to blow-up and dispersion, and that blow-up in the Ozawa solution is generic.

Numerical study of blow-up in the Davey-Stewartson system

KAUST Repository

Klein, Christian; Muite, Benson; Roidot, Kristelle

2013-01-01

Nonlinear dispersive partial differential equations such as the nonlinear Schrödinger equations can have solutions that blow up. We numerically study the long time behavior and potential blow-up of solutions to the focusing Davey-Stewartson II equation by analyzing perturbations of the lump and the Ozawa solutions. It is shown in this way that both are unstable to blow-up and dispersion, and that blow-up in the Ozawa solution is generic.

Self-sustained Oscillation Pulsed Air Blowing System for Energy Saving

Institute of Scientific and Technical Information of China (English)

CAI Maolin; XU Weiqing

2010-01-01

Currently, many studies have been made for years on dimensions of pneumatic nozzle, which influence the flow characteristic of blowing system. For the purpose of outputting the same blowing force, the supply pressure could be reduced by decreasing the ratio of length to diameter of nozzle. The friction between high speed air and pipe wall would be reduced if the nozzle is designed to be converging shape comparing with straight shape. But the volume flow and pressure, discussed in these studies, do not describe energy loss of the blowing system directly. Pneumatic power is an innovative principle to estimate pneumatic system's energy consumption directly. Based on the above principle, a pulse blowing method is put forward for saving energy. A flow experiment is carried out, in which the high speed air flows from the pulse blowing system and continuous blowing system respectively to a plate with grease on top. Supply pressure and the volume of air used for removing the grease are measured to calculate energy consumption. From the experiment result, the pulse blowing system performs to conserve energy comparing with the continuous blowing system. The frequency and duty ratio of pulse flow influence the blowing characteristic. The pulse blowing system performs to be the most efficient at the specified frequency and duty ratio. Then a pneumatic self-oscillated method based on air operated valve is put forward to generate pulse flow. A simulation is made about dynamic modeling the air operated valve and calculating the motion of the valve core and output pressure. The simulation result verifies the system to be able to generate pulse flow, and predicts the key parameters of the frequency and duty ratio measured by experiment well. Finally, on the basis of simplifying and solution of the pulse blowing system's mathematic model, the relationship between system's frequency duty ratio and the dimensions of components is simply described with four algebraic equations. The

Control rod blow out protection system

International Nuclear Information System (INIS)

Dietrich, J.R.; Flinn, W.S.; Groves, M.D.

1979-01-01

An absorber element blow-out protection system for a nuclear reactor having a pressure vessel through which a coolant is circulated. The blow-out protection system includes devices which hydraulically couple groups of guide tubes in which the absorber elements move, the coupling devices limiting coolant lift flow rate to a level commensurate with the raising of individual absorber elements but insufficient to raise a plurality of absorber elements simultaneously

Advanced Trailing Edge Blowing Concepts for Fan Noise Control

Directory of Open Access Journals (Sweden)

Cezar RIZEA

2012-03-01

Full Text Available This study documents trailing edge blowing research performed to reduce rotor / stator interaction noise in turbofan engines. The existing technique of filling every velocity deficit requires a large amount of air and is therefore impractical. The purpose of this research is to investigate new blowing configurations in order to achieve noise reduction with lesser amounts of air. Using the new configurations air is not injected into every fan blade, but is instead varied circumferentially. For example, blowing air may be applied to alternating fan blades. This type of blowing configuration both reduces the amount of air used and changes the spectral shape of the tonal interaction noise. The original tones at the blade passing frequency and its harmonics are reduced and new tones are introduced between them. This change in the tonal spectral shape increases the performance of acoustic liners used in conjunction with trailing edge blowing.

Comparison on Promotion Effect of Various Types of Surfactants on HCFC-141b Hydrate Induction Time

Science.gov (United States)

Li, Juan; Sun, Zhigao; Liu, Chenggang; Zhu, Minggui

2018-03-01

Cold storage in air conditioning based on refrigerant hydrate is a new-type energy saving technology to reduce initial investment and running cost of air conditioning equipments and improve system stability. Refrigerant hydrate is generated under critical temperature and pressure condition, while surfactant is an effective medium to promote its phase equilibrium. In this paper, in order to research such promotion effect, different type of surfactants with unique mechanism, SDS, Tween80 and Span80, n-BA were selected to compare the respective impact on HCFC141b hydrate induction time based on temperature curve. Experimental results showed that no obvious change had been discovered when no surfactant was added into pure water system, which coincided with phase equilibrium diagram of HCFC141b. All the four kinds of surfactants had realized promotion effect to various degrees. For each hydration system, a large gap existed between the longest and the shortest induction time in 6 groups of parallel experiments, meaning relatively poor system stability. Under the combined effect of Tween80 (2wt%), Span80 (0.1wt%) and n-BA (0.1wt%), average and the shortest induction time was 20.9min and 17.5min respectively, corresponding to the best promotion effect.

Blow-Up Time for Nonlinear Heat Equations with Transcendental Nonlinearity

Directory of Open Access Journals (Sweden)

Hee Chul Pak

2012-01-01

Full Text Available A blow-up time for nonlinear heat equations with transcendental nonlinearity is investigated. An upper bound of the first blow-up time is presented. It is pointed out that the upper bound of the first blow-up time depends on the support of the initial datum.

Blow Flies Visiting Decaying Alligators: Is Succession Synchronous or Asynchronous?

Directory of Open Access Journals (Sweden)

Mark P. Nelder

2009-01-01

Full Text Available Succession patterns of adult blow flies (Diptera: Calliphoridae on decaying alligators were investigated in Mobile (Ala, USA during August 2002. The most abundant blow fly species visiting the carcasses were Chrysomya rufifacies (Macquart, Cochliomyia macellaria (Fabricus, Chrysomya megacephala (Fabricus, Phormia regina (Meigen, and Lucilia coeruleiviridis (Macquart. Lucilia coeruleiviridis was collected more often during the early stages of decomposition, followed by Chrysomya spp., Cochliomyia macellaria, and Phormia regina in the later stages. Lucilia coeruleiviridis was the only synchronous blow fly on the three carcasses; other blow fly species exhibited only site-specific synchrony. Using dichotomous correlations and analyses of variance, we demonstrated that blow fly-community succession was asynchronous among three alligators; however, Monte Carlo simulations indicate that there was some degree of synchrony between the carcasses.

Rate constant for the reaction of OH with CH3CCl2F (HCFC-141b) determined by relative rate measurements with CH4 and CH3CCl3

Science.gov (United States)

Huder, Karin; Demore, William B.

1993-01-01

Determination of accurate rate constants for OH abstraction is of great importance for the calculation of lifetimes for HCFCs and their impact on the atmosphere. For HCFC-141b there has been some disagreement in the literature for absolute measurements of this rate constant. In the present work rate constant ratios for HCFC-141b were measured at atmospheric pressure in the temperature range of 298-358 K, with CH4 and CH3CCl3 as reference gases. Ozone was photolyzed at 254 nm in the presence of water vapor to produce OH radicals. Relative depletions of 141b and the reference gases were measured by FTIR. Arrhenius expressions for 141b were derived from each reference gas and found to be in good agreement with each other. The combined expression for HCFC-141b which we recommend is 1.4 x 10 exp -12 exp(-1630/T) with k at 298 K being 5.9 x 10 exp -15 cu cm/molec-s. This value is in excellent agreement with the JPL 92-20 recommendation.

Simulation of the Two Stages Stretch-Blow Molding Process: Infrared Heating and Blowing Modeling

International Nuclear Information System (INIS)

Bordival, M.; Schmidt, F. M.; Le Maoult, Y.; Velay, V.

2007-01-01

In the Stretch-Blow Molding (SBM) process, the temperature distribution of the reheated perform affects drastically the blowing kinematic, the bottle thickness distribution, as well as the orientation induced by stretching. Consequently, mechanical and optical properties of the final bottle are closely related to heating conditions. In order to predict the 3D temperature distribution of a rotating preform, numerical software using control-volume method has been developed. Since PET behaves like a semi-transparent medium, the radiative flux absorption was computed using Beer Lambert law. In a second step, 2D axi-symmetric simulations of the SBM have been developed using the finite element package ABAQUS registered . Temperature profiles through the preform wall thickness and along its length were computed and applied as initial condition. Air pressure inside the preform was not considered as an input variable, but was automatically computed using a thermodynamic model. The heat transfer coefficient applied between the mold and the polymer was also measured. Finally, the G'sell law was used for modeling PET behavior. For both heating and blowing stage simulations, a good agreement has been observed with experimental measurements. This work is part of the European project ''APT P ACK'' (Advanced knowledge of Polymer deformation for Tomorrow's PACKaging)

Simulation of the Two Stages Stretch-Blow Molding Process: Infrared Heating and Blowing Modeling

Science.gov (United States)

Bordival, M.; Schmidt, F. M.; Le Maoult, Y.; Velay, V.

2007-05-01

In the Stretch-Blow Molding (SBM) process, the temperature distribution of the reheated perform affects drastically the blowing kinematic, the bottle thickness distribution, as well as the orientation induced by stretching. Consequently, mechanical and optical properties of the final bottle are closely related to heating conditions. In order to predict the 3D temperature distribution of a rotating preform, numerical software using control-volume method has been developed. Since PET behaves like a semi-transparent medium, the radiative flux absorption was computed using Beer Lambert law. In a second step, 2D axi-symmetric simulations of the SBM have been developed using the finite element package ABAQUS®. Temperature profiles through the preform wall thickness and along its length were computed and applied as initial condition. Air pressure inside the preform was not considered as an input variable, but was automatically computed using a thermodynamic model. The heat transfer coefficient applied between the mold and the polymer was also measured. Finally, the G'sell law was used for modeling PET behavior. For both heating and blowing stage simulations, a good agreement has been observed with experimental measurements. This work is part of the European project "APT_PACK" (Advanced knowledge of Polymer deformation for Tomorrow's PACKaging).

Manufacturing a Porous Structure According to the Process Parameters of Functional 3D Porous Polymer Printing Technology Based on a Chemical Blowing Agent

Science.gov (United States)

Yoo, C. J.; Shin, B. S.; Kang, B. S.; Yun, D. H.; You, D. B.; Hong, S. M.

2017-09-01

In this paper, we propose a new porous polymer printing technology based on CBA(chemical blowing agent), and describe the optimization process according to the process parameters. By mixing polypropylene (PP) and CBA, a hybrid CBA filament was manufactured; the diameter of the filament ranged between 1.60 mm and 1.75 mm. A porous polymer structure was manufactured based on the traditional fused deposition modelling (FDM) method. The process parameters of the three-dimensional (3D) porous polymer printing (PPP) process included nozzle temperature, printing speed, and CBA density. Porosity increase with an increase in nozzle temperature and CBA density. On the contrary, porosity increase with a decrease in the printing speed. For porous structures, it has excellent mechanical properties. We manufactured a simple shape in 3D using 3D PPP technology. In the future, we will study the excellent mechanical properties of 3D PPP technology and apply them to various safety fields.

Infrared Absorption Spectra, Radiative Efficiencies, and Global Warming Potentials of Newly-Detected Halogenated Compounds: CFC-113a, CFC-112 and HCFC-133a

Directory of Open Access Journals (Sweden)

Maryam Etminan

2014-07-01

Full Text Available CFC-113a (CF3CCl3, CFC-112 (CFCl2CFCl2 and HCFC-133a (CF3CH2Cl are three newly detected molecules in the atmosphere that are almost certainly emitted as a result of human activity. It is important to characterise the possible contribution of these gases to radiative forcing of climate change and also to provide information on the CO2-equivalence of their emissions. We report new laboratory measurements of absorption cross-sections of these three compounds at a resolution of 0.01 cm−1 for two temperatures 250 K and 295 K in the spectral range of 600–1730 cm−1. These spectra are then used to calculate the radiative efficiencies and global warming potentials (GWP. The radiative efficiencies are found to be between 0.15 and 0.3 W∙m−2∙ppbv−1. The GWP for a 100 year time horizon, relative to carbon dioxide, ranges from 340 for the relatively short-lived HCFC-133a to 3840 for the longer-lived CFC-112. At current (2012 concentrations, these gases make a trivial contribution to total radiative forcing; however, the concentrations of CFC-113a and HCFC-133a are continuing to increase. The 2012 CO2-equivalent emissions, using the GWP (100, are estimated to be about 4% of the current global CO2-equivalent emissions of HFC-134a.

Blowing snow detection from ground-based ceilometers : Application to East Antarctica

NARCIS (Netherlands)

Gossart, Alexandra; Souverijns, Niels; Gorodetskaya, Irina V.; Lhermitte, S.L.M.; Lenaerts, Jan T M; Schween, Jan H.; Mangold, Alexander; Laffineur, Quentin; van Lipzig, Nicole P. M.

2017-01-01

Blowing snow impacts Antarctic ice sheet surface mass balance by snow redistribution and sublimation. However, numerical models poorly represent blowing snow processes, while direct observations are limited in space and time. Satellite retrieval of blowing snow is hindered by clouds and only the

Employee perceptions regarding whistle-blowing in the workplace: A South African perspective

Directory of Open Access Journals (Sweden)

Sandra Perks

2008-11-01

Full Text Available The purpose of whistle-blowing is to eradicate unethical behaviour in the work place. This article investigates the perceptions of South African employees (n=387 employed in medium and large organisations regarding whistle-blowing. Respondents regard personal viewpoints and the supportive organisational environment as determining factors for whistle-blowing. South African employees have faced minimal negative consequences and will again engage in whistle-blowing, regardless of union support. Organisations can create a whistle-blowing culture by having a personal code of ethics, using hotlines, having an ethical committee, engaging in periodic ethics training and doing an annual ethical audit.

Whistle Blowing: What Do Contemporary Ethical Theories Say?

Directory of Open Access Journals (Sweden)

Bosupeng Mpho

2017-04-01

Full Text Available The rising number of scandals leading to the closure of many large companies is worrisome. The traditional belief is that business and ethics are oxymorons and one is not expected to be totally virtuous during business operations. Nonetheless, this does not mean ethical standards should be side-lined. Professional associations such as the Chartered Financial Institute (CFA uphold moral values and urge members to exercise high moral standards and diligence in their duties. Philosophically, major accounting scandals could have been nipped in the bud by whistle blowing before the wrong deeds escalated. However whistle blowing is a major issue and is viewed as disloyalty. In this paper, the dilemmas of whistle blowing are evaluated using contemporary ethical theories which are: egoism, deontology and utilitarianism. The analysis shows that deontology and utilitarianism are based on altruism and may support whistle blowing because they are grounded on consideration of other people. It is worth noting that morally upright adults are often a result of being brought up as ethical children from a psychological standpoint.

Simple gases to replace non-environmentally friendly polymer foaming agents. A thermodynamic investigation

International Nuclear Information System (INIS)

Grolier, Jean-Pierre E.; Randzio, Stanislaw L.

2012-01-01

Highlights: ► The PVT-vibrating wire technique and PVT-scanning transitiometry. ► Polymer swelling with measured gas sorption and gas–polymer interaction energies. ► Experimental measurements up to 373 K and 100 MPa. ► Hydrostatic and plasticization effects under high pressure gas and induced T g -shifts. ► Thermodynamic study of the (gas + polymer) systems polystyrene with CO 2 , N 2 , and freons. - Abstract: Foaming constitutes one of the most important industrial activities in polymer engineering to produce efficient thermal insulating materials. In particular, rigid insulating boards are produced worldwide on a large scale using blowing agents which eventually are released in the environment where they adversely impact the natural friendly stratospheric ozone layer. Concomitantly, the chemicals used as blowing agents contribute to the creation of the unfriendly tropospheric ozone layer generating the disastrous green house effect around our planet. The traditional foaming intermediates currently named freons, like chlorofluorocarbons (CFCs) currently used as blowing agents as well as the hydrochlorofluorocarbons (HCFCs) often considered as alternative blowing agents, must be banned from industrial processes and new (friendly) foaming agents have to be suggested and evaluated in terms of both easy engineering and environmental neutrality. Undoubtedly thermodynamics plays a major role in assessing the effective capability of those chemicals. Some CFCs still accepted and other possible simple gases like carbon dioxide and nitrogen have been considered. The in-depth thermodynamic investigation has been made possible thanks to new experimental developments to determine gas solubility in polymers and associated swelling as well as the thermodynamic properties of (gas + polymer) systems, including the thermophysical properties of polymers under gas sorption. Pertinent data have been generated for such properties over extended T and p ranges.

Matrix isolation infrared spectroscopic and theoretical study of 1,1,1-trifluoro-2-chloroethane (HCFC-133a)

Science.gov (United States)

Rodrigues, Gessenildo Pereira; Lucena, Juracy Régis; Ventura, Elizete; Andrade do Monte, Silmar; Reva, Igor; Fausto, Rui

2013-11-01

The molecular structure and infrared spectrum of the atmospheric pollutant 1,1,1-trifluoro-2-chloroethane (HCFC-133a; CF3CH2Cl) in the ground electronic state were characterized experimentally and theoretically. Excited state calculations (at the CASSCF, MR-CISD, and MR-CISD+Q levels) have also been performed in the range up to ˜9.8 eV. The theoretical calculations show the existence of one (staggered) conformer, which has been identified spectroscopically for the monomeric compound isolated in cryogenic (˜10 K) argon and xenon matrices. The observed infrared spectra of the matrix-isolated HCFC-133a were interpreted with the aid of MP2/aug-cc-pVTZ calculations and normal coordinate analysis, which allowed a detailed assignment of the observed spectra to be carried out, including identification of bands due to different isotopologues (35Cl and 37Cl containing molecules). The calculated energies of the several excited states along with the values of oscillator strengths and previous results obtained for CFCs and HCFCs suggest that the previously reported photolyses of the title compound at 147 and 123.6 nm [T. Ichimura, A. W. Kirk, and E. Tschuikow-Roux, J. Phys. Chem. 81, 1153 (1977)] are likely to be initiated in the n-4s and n-4p Rydberg states, respectively.

Development and implementation of Intelligent Soot Blowing Optimization System for TNB Janamanjung

Directory of Open Access Journals (Sweden)

Sundaram Taneshwaren

2017-01-01

Full Text Available With an ever increasing demand for energy, Malaysia has become a nation that thrives on solid power generation sector to meet the energy demand and supply market. In a coal fired power plant, soot blowing operation is commonly used as a cleaning mechanism inside the boiler. There are many types of sequence available for this soot blowing operation. Hence, there is no efficient ways in utilizing the soot blowing operation to enhance the efficiency of boiler. Soot blowing optimization requires specific set of data preparation and simulation in order to achieve the best modal. Computational Fluid Dynamics (CFD is used to model a 700MW super-critical boiler, whereby parameters with effect to soot blowing operation is studied. Two different boiler condition is studied to analyze parameters in a clean and faulty boiler. Artificial Neural Network (ANN is used to train neural network modal with back propagation method to determine the best modal that will be used to predict soot blowing operation. Combination of neural network different number of neurons, hidden layers, training algorithm, and training functions is trained to find the modal with lowest error. By improving soot blowing sequence, efficiency of boiler can be improved by providing best parameter and model. This model is then used as a reference for advisory tool whereby a Neural Network Predictive Tool is suggested to the station to predict the soot blowing operation that occurs.

Helical instability in film blowing process: Analogy to buckling instability

Science.gov (United States)

Lee, Joo Sung; Kwon, Ilyoung; Jung, Hyun Wook; Hyun, Jae Chun

2017-12-01

The film blowing process is one of the most important polymer processing operations, widely used for producing bi-axially oriented film products in a single-step process. Among the instabilities observed in this film blowing process, i.e., draw resonance and helical motion occurring on the inflated film bubble, the helical instability is a unique phenomenon portraying the snake-like undulation motion of the bubble, having the period on the order of few seconds. This helical instability in the film blowing process is commonly found at the process conditions of a high blow-up ratio with too low a freezeline position and/or too high extrusion temperature. In this study, employing an analogy to the buckling instability for falling viscous threads, the compressive force caused by the pressure difference between inside and outside of the film bubble is introduced into the simulation model along with the scaling law derived from the force balance between viscous force and centripetal force of the film bubble. The simulation using this model reveals a close agreement with the experimental results of the film blowing process of polyethylene polymers such as low density polyethylene and linear low density polyethylene.

The effects of local blowing perturbations on thermal turbulent structures

Science.gov (United States)

Liu, Can; Araya, Guillermo; Leonardi, Stefano; Castillo, Luciano

2013-11-01

Blowing is an active flow control technique with several industrial applications, particularly in film cooling of turbine blades. In the past, the effects of localized blowing have been mostly analyzed on the velocity field and its influence of the flow parameters and turbulence structures (Krogstad and Kourakine, 2000). However, little literature can be found on the effects of blowing on the coherent thermal structures. In the present study, an incompressible turbulent channel flow with given steady blowing at the wall is simulated via DNS by means of five spanwise holes. The Reynolds number based on the friction velocity and half channel height is approximately Re = 394 and the molecular Prandtl number is Pr = 0.71. Temperature is considered a passive scalar with isothermal conditions at the wall. Different blowing amplitudes and perturbing angles (with respect to the streamwise direction) are applied to find out their effects on the turbulent thermal structures by means of a two-point correlation analysis. In addition, local reduction and increase of drag are connected to vorticity. The corresponding influence of perturbing amplitudes and angles on the energy budget of thermal fluctuations and turbulent Prandtl numbers are also shown and discussed.

New Perspectives on Blowing Snow Transport, Sublimation, and Layer Thermodynamic Structure over Antarctica

Science.gov (United States)

Palm, Steve; Kayetha, Vinay; Yang, Yuekui; Pauly, Rebecca M.

2017-01-01

Blowing snow over Antarctica is a widespread and frequent event. Satellite remote sensing using lidar has shown that blowing snow occurs over 70% of the time over large areas of Antarctica in winter. The transport and sublimation of blowing snow are important terms in the ice sheet mass balance equation and the latter is also an important part of the hydrological cycle. Until now the only way to estimate the magnitude of these processes was through model parameterization. We present a technique that uses direct satellite observations of blowing snow and model (MERRA-2) temperature and humidity fields to compute both transport and sublimation of blowing snow over Antarctica for the period 2006 to 2016. The results show a larger annual continent-wide integrated sublimation than current published estimates and a significant transport of snow from continent to ocean. The talk will also include the lidar backscatter structure of blowing snow layers that often reach heights of 200 to 300 m as well as the first dropsonde measurements of temperature, moisture and wind through blowing snow layers.

Some blow-up problems for a semilinear parabolic equation with a potential

Science.gov (United States)

Cheng, Ting; Zheng, Gao-Feng

The blow-up rate estimate for the solution to a semilinear parabolic equation u=Δu+V(x)|u in Ω×(0,T) with 0-Dirichlet boundary condition is obtained. As an application, it is shown that the asymptotic behavior of blow-up time and blow-up set of the problem with nonnegative initial data u(x,0)=Mφ(x) as M goes to infinity, which have been found in [C. Cortazar, M. Elgueta, J.D. Rossi, The blow-up problem for a semilinear parabolic equation with a potential, preprint, arXiv: math.AP/0607055, July 2006], is improved under some reasonable and weaker conditions compared with [C. Cortazar, M. Elgueta, J.D. Rossi, The blow-up problem for a semilinear parabolic equation with a potential, preprint, arXiv: math.AP/0607055, July 2006].

Blow-up for a three dimensional Keller-Segel model with consumption of chemoattractant

Science.gov (United States)

Jiang, Jie; Wu, Hao; Zheng, Songmu

2018-04-01

We investigate blow-up properties for the initial-boundary value problem of a Keller-Segel model with consumption of chemoattractant when the spatial dimension is three. Through a kinetic reformulation of the Keller-Segel system, we first derive some higher-order estimates and obtain certain blow-up criteria for the local classical solutions. These blow-up criteria generalize the results in [4,5] from the whole space R3 to the case of bounded smooth domain Ω ⊂R3. Lower global blow-up estimate on ‖ n ‖ L∞ (Ω) is also obtained based on our higher-order estimates. Moreover, we prove local non-degeneracy for blow-up points.

Blowing snow detection in Antarctica, from space borne and ground-based remote sensing

Science.gov (United States)

Gossart, A.; Souverijns, N.; Lhermitte, S.; Lenaerts, J.; Gorodetskaya, I.; Schween, J. H.; Van Lipzig, N. P. M.

2017-12-01

Surface mass balance (SMB) strongly controls spatial and temporal variations in the Antarctic Ice Sheet (AIS) mass balance and its contribution to sea level rise. Currently, the scarcity of observational data and the challenges of climate modelling over the ice sheet limit our understanding of the processes controlling AIS SMB. Particularly, the impact of blowing snow on local SMB is not yet constrained and is subject to large uncertainties. To assess the impact of blowing snow on local SMB, we investigate the attenuated backscatter profiles from ceilometers at two East Antarctic locations in Dronning Maud Land. Ceilometers are robust ground-based remote sensing instruments that yield information on cloud base height and vertical structure, but also provide information on the particles present in the boundary layer. We developed a new algorithm to detect blowing snow (snow particles lifted by the wind from the surface to substantial height) from the ceilometer attenuated backscatter. The algorithm successfully allows to detect strong blowing snow signal from layers thicker than 15 m at the Princess Elisabeth (PE, (72°S, 23°E)) and Neumayer (70°S, 8° W) stations. Applying the algorithm to PE, we retrieve the frequency and annual cycle of blowing snow as well as discriminate between clear sky and overcast conditions during blowing snow. We further apply the blowing snow algorithm at PE to evaluate the blowing snow events detection by satellite imagery (Palm et al., 2011): the near-surface blowing snow layers are apparent in lidar backscatter profiles and enable snowdrift events detection (spatial and temporal frequency, height and optical depth). These data are processed from CALIPSO, at a high resolution (1x1 km digital elevation model). However, the remote sensing detection of blowing snow events by satellite is limited to layers of a minimal thickness of 20-30 m. In addition, thick clouds, mostly occurring during winter storms, can impede drifting snow

Origins of transverse emittance blow-up during the LHC energy tramp

CERN Document Server

Kuhn, M; Arduini, G; Kain, V; Schaumann, M; Tomas, R

2014-01-01

During LHC Run 1 about 30 % of the potential peak performance was lost due to transverse emittance blow-up through the LHC cycle. Measurements indicated that the majority of the blow-up occurred during the energy ramp. Until the end of LHC Run 1 this emittance blow-up could not be eliminated. In this paper the measurements and observations of emittance growth through the ramp are summarized. Simulation results for growth due to Intra Beam Scattering will be shown and compared to measurements. A summary of investigations of other possible sources will be given and backed up with simulations where possible. Requirements for commissioning the LHC with beam in 2015 after Long Shutdown 1 to understand and control emittance blow-up will be listed.

Blow-up in nonlinear Schroedinger equations. II. Similarity structure of the blow-up singularity

DEFF Research Database (Denmark)

Rypdal, K.; Juul Rasmussen, Jens

1986-01-01

invariance and generalizations of the latter. This generalized "quasi-invariance" reveals the nature of the blow-up singularity and resolves an old controversy. Most of the previous work has been done on the cubic nonlinearity. We generalize the results to an arbitrary power nonlinearity....

Religiosity, Job Status and Whistle-Blowing: Evidence from Micro-Finance Companies

Directory of Open Access Journals (Sweden)

Emmanuel Selase Asamoah

2016-03-01

Full Text Available We investigate the effect of religiosity and job status on whistle-blowing among employees of micro finance companies in Ga-East district of Ghana. The intellectual dimension of religiosity informs and produces high sense of morality in an individual thus influencing whistle-blowing. Additionally, religion create the platform for building belief in certain rules and regulations as right or as wrong. Using quantitative approach for analyzing the effect between independent variables (job status and religiosity on the dependent variable (whistle-blowing, we show that though religiosity and job status can influence whistle-blowing, however in this study, the magnitude is negligible and perhaps other variables in concert with religiosity and job status may influence whistle-blowing activities in an organization. We conclude that that whistleblowing generally in the Ghanaian setting is yet to receive high prominence due to the general belief of lack of protection for persons who come out to expose wrongdoings and the general fear of harassment, victimization and loss of job by the whistle-blower.

Occurrence of blow fly species (Diptera: calliphoridae) in Phitsanulok Province, Northern Thailand.

Science.gov (United States)

Bunchu, Nophawan; Sukontason, Kom; Sanit, Sangob; Chidburee, Polprecha; Kurahashi, Hiromu; Sukontason, Kabkaew L

2012-12-01

Based on the current forensic importance of blow flies (Diptera: Calliphoridae), their biological aspects have been studied increasingly worldwide. The blow fly fauna in Phitsanulok Province, Northern Thailand was studied from May 2009 to April 2010 in the residential, agricultural, mountainous and forested areas of Muang, Wat Bot, Nakhon Thai and Wang Thong districts, respectively, in order to know the occurrence of blow flies in this province. Collections were carried out monthly using commercial funnel fly traps and sweeping methods, with 1-day tainted pork viscera as bait. Identification of adult blow flies exhibited 14 634 specimens, comprising of 5 subfamilies, 14 genera and 36 species. Chrysomya megacephala (Fabricius, 1794) and Achoetandrus rufifacies (Macquart, 1843) were the most and second most abundant species trapped, respectively. These two species of carrion flies prevailed in all the types of land investigated. We calculated and compared the diversity indices, species evenness and richness, and similarity coefficients of the blow fly species in various areas. The data from this study may be used to identify the potential of forensicallyimportant fly species within Phitsanulok Province and fulfill the information on blow fly fauna in Thailand.

Blow up of solutions to ordinary differential equations arising in nonlinear dispersive problems

Directory of Open Access Journals (Sweden)

Milena Dimova

2018-03-01

Full Text Available We study a new class of ordinary differential equations with blow up solutions. Necessary and sufficient conditions for finite blow up time are proved. Based on the new differential equation, a revised version of the concavity method of Levine is proposed. As an application we investigate the non-existence of global solutions to the Cauchy problem of Klein-Gordon, and to the double dispersive equations. We obtain necessary and sufficient condition for finite time blow up with arbitrary positive energy. A very general sufficient condition for blow up is also given.

'Whistle-blowing' and the quandary of policy implementation in Nigeria

African Journals Online (AJOL)

Nigeria as a country has undergone series of economic policies and Programs to bring her economy back on track. These policies range from National Development Plan to the present day whistle-blowing policy. The whistle blowing policy was introduced by the administration of President Buhari in December, 2016, with a ...

Blow-up : A free lunch?

NARCIS (Netherlands)

Koenderink, J.J.; Richards, W.; Van Doorn, A.J.

2012-01-01

We consider operations that change the size of images, either shrinks or blow-ups. Image processing offers numerous possibilities, put at everyone’s disposal with such computer programs as Adobe Photoshop. We consider a different class of operations, aimed at immediate visual awareness, rather than

Thermal large Eddy simulations and experiments in the framework of non-isothermal blowing

International Nuclear Information System (INIS)

Brillant, G.

2004-06-01

The aim of this work is to study thermal large-eddy simulations and to determine the nonisothermal blowing impact on a turbulent boundary layer. An experimental study is also carried out in order to complete and validate simulation results. In a first time, we developed a turbulent inlet condition for the velocity and the temperature, which is necessary for the blowing simulations.We studied the asymptotic behavior of the velocity, the temperature and the thermal turbulent fluxes in a large-eddy simulation point of view. We then considered dynamics models for the eddy-diffusivity and we simulated a turbulent channel flow with imposed temperature, imposed flux and adiabatic walls. The numerical and experimental study of blowing permitted to obtain to the modifications of a thermal turbulent boundary layer with the blowing rate. We observed the consequences of the blowing on mean and rms profiles of velocity and temperature but also on velocity-velocity and velocity-temperature correlations. Moreover, we noticed an increase of the turbulent structures in the boundary layer with blowing. (author)

HFC-23 (CHF3 emission trend response to HCFC-22 (CHClF2 production and recent HFC-23 emission abatement measures

Directory of Open Access Journals (Sweden)

R. G. Prinn

2010-08-01

Full Text Available HFC-23 (also known as CHF3, fluoroform or trifluoromethane is a potent greenhouse gas (GHG, with a global warming potential (GWP of 14 800 for a 100-year time horizon. It is an unavoidable by-product of HCFC-22 (CHClF2, chlorodifluoromethane production. HCFC-22, an ozone depleting substance (ODS, is used extensively in commercial refrigeration and air conditioning, in the extruded polystyrene (XPS foam industries (dispersive applications and also as a feedstock in fluoropolymer manufacture (a non-dispersive use. Aside from small markets in specialty uses, HFC-23 has historically been considered a waste gas that was, and often still is, simply vented to the atmosphere. Efforts have been made in the past two decades to reduce HFC-23 emissions, including destruction (incineration in facilities in developing countries under the United Nations Framework Convention on Climate Change's (UNFCCC Clean Development Mechanism (CDM, and by process optimization and/or voluntary incineration by most producers in developed countries. We present observations of lower-tropospheric mole fractions of HFC-23 measured by "Medusa" GC/MSD instruments from ambient air sampled in situ at the Advanced Global Atmospheric Gases Experiment (AGAGE network of five remote sites (2007–2009 and in Cape Grim air archive (CGAA samples (1978–2009 from Tasmania, Australia. These observations are used with the AGAGE 2-D atmospheric 12-box model and an inverse method to produce model mole fractions and a "top-down" HFC-23 emission history. The model 2009 annual mean global lower-tropospheric background abundance is 22.6 (±0.2 pmol mol−1. The derived HFC-23 emissions show a "plateau" during 1997–2003, followed by a rapid ~50% increase to a peak of 15.0 (+1.3/−1.2 Gg/yr in 2006. Following this peak, emissions of HFC-23 declined rapidly to 8.6 (+0.9/−1.0 Gg/yr in 2009, the lowest annual emission of the past 15 years. We derive a 1990–2008 "bottom-up" HFC-23 emission history

Numerical and experimental study of blowing jet on a high lift airfoil

Science.gov (United States)

Bobonea, A.; Pricop, M. V.

2013-10-01

Active manipulation of separated flows over airfoils at moderate and high angles of attack in order to improve efficiency or performance has been the focus of a number of numerical and experimental investigations for many years. One of the main methods used in active flow control is the usage of blowing devices with constant and pulsed blowing. Through CFD simulation over a 2D high-lift airfoil, this study is trying to highlight the impact of pulsed blowing over its aerodynamic characteristics. The available wind tunnel data from INCAS low speed facility are also beneficial for the validation of the numerical analysis. This study intends to analyze the impact of the blowing jet velocity and slot geometry on the efficiency of an active flow control.

Field observations of the electrostatic charges of blowing snow in Hokkaido, Japan

Science.gov (United States)

Omiya, S.; Sato, A.

2011-12-01

An electrostatic charge of blowing snow may be a contributing factor in the formation of a snow drift and a snow cornice, and changing of the trajectory of own motion. However, detailed electrification characteristics of blowing snow are not known as there are few reports of charge measurements. We carried out field observations of the electrostatic charges of blowing snow in Tobetsu, Hokkaido, Japan in the mid winter of 2011. An anemovane and a thermohygrometer were used for the meteorological observation. Charge-to-mass ratios of blowing snow were obtained by a Faraday-cage, an electrometer and an electric balance. In this observation period, the air temperature during the blowing snow event was -6.5 to -0.5 degree Celsius. The measured charges in this observation were consistent with the previous studies in sign, which is negative, but they were smaller than the previous one. In most cases, the measured values increased with the temperature decrease, which corresponds with previous studies. However, some results contradicted the tendency, and the maximum value was obtained on the day of the highest air temperature of -0.5 degree Celsius. This discrepancy may be explained from the difference of the snow surface condition on observation day. The day when the maximum value was obtained, the snow surface was covered with old snow, and hard. On the other hand, in many other cases, the snow surface was covered with the fresh snow, and soft. Blowing snow particles on the hard surface can travel longer distance than on the soft one. Therefore, it can be surmised that the hard surface makes the blowing snow particles accumulate a lot of negative charges due to a large number of collisions to the surface. This can be supported by the results of the wind tunnel experiments by Omiya and Sato (2011). By this field observation, it was newly suggested that the electrostatic charge of blowing snow are influenced greatly by the difference of the snow surface condition. REFERENCE

Dynamic shock wave: hammer blow

International Nuclear Information System (INIS)

Lackme, Claude

1978-01-01

The general properties of shocks, their generation and the conditions of reflexion to an interface are dealt with in turn. By then applying these concepts to a liquid column and its environment (wall, free area, closing devices) the hammer blow is presented as being a relatively weak shock [fr

Developing and teaching the virtue-ethics foundations of healthcare whistle blowing.

Science.gov (United States)

Faunce, Thomas

2004-10-01

Healthcare whistle blowing, despite the benefits it has brought to healthcare systems in many developed countries, remains generally regarded as a pariah activity by many of the most influential healthcare professionals and regulatory institutions. Few if any medical schools or law department health law and bioethics classes, teach whistle blowing in a formal sense. Yet without exception, public inquiries initiated by healthcare whistle blowers have validated their central allegations and demonstrated that the whistle blowers themselves were sincere in their desire to implement the fundamental virtues and principles of medical ethics, bioethics and public health law. In many jurisdictions, the law, this time remarkably in advance of professional opinion, has offered legislative protection for reasonable allegations of whistleblowers made in good faith and in the public interest concerning a substantial and imminent threat to public safety. One reason for this paradoxical position, explored here, is that healthcare whistle blowing lacks a firm virtue-based theoretical bioethical and jurisprudential foundation. The hypothesis discussed is that the lack of this bioethical and jurisprudential substrate has contributed to a situation where healthcare whistle blowing suffers in terms of institutional support due to its lack of academic legitimacy. This article commences the process of redressing this imbalance by attempting to lay the theoretical foundations for healthcare whistle blowing. As a case study, this article concludes by discussing the Personal and Professional Development course at the ANU Medical School where healthcare whistle blowing is a formal part of a virtue-based curriculum that emphasises the foundational importance of conscience. Illustrative elements of that program are discussed.

On the effect of leading edge blowing on circulation control airfoil aerodynamics

Science.gov (United States)

Mclachlan, B. G.

1987-01-01

In the present context the term circulation control is used to denote a method of lift generation that utilizes tangential jet blowing over the upper surface of a rounded trailing edge airfoil to determine the location of the boundary layer separation points, thus setting an effective Kutta condition. At present little information exists on the flow structure generated by circulation control airfoils under leading edge blowing. Consequently, no theoretical methods exist to predict airfoil performance under such conditions. An experimental study of the flow field generated by a two dimensional circulation control airfoil under steady leading and trailing edge blowing was undertaken. The objective was to fundamentally understand the overall flow structure generated and its relation to airfoil performance. Flow visualization was performed to define the overall flow field structure. Measurements of the airfoil forces were also made to provide a correlation of the observed flow field structure to airfoil performance. Preliminary results are presented, specifically on the effect on the flow field structure of leading edge blowing, alone and in conjunction with trailing edge blowing.

Sounds of Silence: Organisational trust and decisions to blow the whistle

Directory of Open Access Journals (Sweden)

Elli Binikos

2008-11-01

Full Text Available Whistleblowing is a form of pro-social behaviour that occurs when an employee reports organisational wrongdoing to an authority able to implement corrective action. While a number of social factors may infuence an employee’s decision to blow the whistle, very little cognisance is given to the role of organisational trust. Since whistleblowing situations often pose problems for whistleblowers, organisational trust becomes an important facilitator for the decision to blow the whistle. Drawing on a case study, this paper shows that when trust exists, employees are more likely to blow the whistle and to do so internally rather than externally.

A One-Dimensional Global-Scaling Erosive Burning Model Informed by Blowing Wall Turbulence

Science.gov (United States)

Kibbey, Timothy P.

2014-01-01

A derivation of turbulent flow parameters, combined with data from erosive burning test motors and blowing wall tests results in erosive burning model candidates useful in one-dimensional internal ballistics analysis capable of scaling across wide ranges of motor size. The real-time burn rate data comes from three test campaigns of subscale segmented solid rocket motors tested at two facilities. The flow theory admits the important effect of the blowing wall on the turbulent friction coefficient by using blowing wall data to determine the blowing wall friction coefficient. The erosive burning behavior of full-scale motors is now predicted more closely than with other recent models.

Gas Release Behavior of Cu-TiH2 Composite Powder and Its Application as a Blowing Agent to Fabricate Aluminum Foams with Low Porosity and Small Pore Size

Science.gov (United States)

Cheng, Ying; Li, Yanxiang; Chen, Xiang; Liu, Zhiyong; Zhou, Xu; Wang, Ningzhen

2018-03-01

Compared to traditional pore structure with high porosity (≥ 80 pct) and large pore size (≥ 3 mm), aluminum foams with low porosity (60 to 70 pct) and small pore size (≤ 2 mm) possess higher compressive property and formability. In order to achieve the goal of reducing pore size, Cu-TiH2 composite powder prepared by ball milling preoxidized TiH2 with Cu powder was used as a blowing agent. Its gas release behavior was characterized by thermogravimetric analysis and differential scanning calorimetry. The results show that the ball milling treatment can advance the gas release process and slow the gas release rate at the same time. All these changes are favorable to the reduction of porosity and pore size. Such Cu-TiH2 composite powder provides an alternative way to fabricate aluminum foams with low porosity and small pore size.

Gas Release Behavior of Cu-TiH2 Composite Powder and Its Application as a Blowing Agent to Fabricate Aluminum Foams with Low Porosity and Small Pore Size

Science.gov (United States)

Cheng, Ying; Li, Yanxiang; Chen, Xiang; Liu, Zhiyong; Zhou, Xu; Wang, Ningzhen

2018-06-01

Compared to traditional pore structure with high porosity (≥ 80 pct) and large pore size (≥ 3 mm), aluminum foams with low porosity (60 to 70 pct) and small pore size (≤ 2 mm) possess higher compressive property and formability. In order to achieve the goal of reducing pore size, Cu-TiH2 composite powder prepared by ball milling preoxidized TiH2 with Cu powder was used as a blowing agent. Its gas release behavior was characterized by thermogravimetric analysis and differential scanning calorimetry. The results show that the ball milling treatment can advance the gas release process and slow the gas release rate at the same time. All these changes are favorable to the reduction of porosity and pore size. Such Cu-TiH2 composite powder provides an alternative way to fabricate aluminum foams with low porosity and small pore size.

A Basic Study on Countermeasure Against Aerodynamic Force Acting on Train Running Inside Tunnel Using Air Blowing

Science.gov (United States)

Suzuki, Masahiro; Nakade, Koji

A basic study of flow controls using air blowing was conducted to reduce unsteady aerodynamic force acting on trains running in tunnels. An air blowing device is installed around a model car in a wind tunnel. Steady and periodic blowings are examined utilizing electromagnetic valves. Pressure fluctuations are measured and the aerodynamic force acting on the car is estimated. The results are as follows: a) The air blowing allows reducing the unsteady aerodynamic force. b) It is effective to blow air horizontally at the lower side of the car facing the tunnel wall. c) The reduction rate of the unsteady aerodynamic force relates to the rate of momentum of the blowing to that of the uniform flow. d) The periodic blowing with the same frequency as the unsteady aerodynamic force reduces the aerodynamic force in a manner similar to the steady blowing.

Mathematical model of whole-process calculation for bottom-blowing copper smelting

Science.gov (United States)

Li, Ming-zhou; Zhou, Jie-min; Tong, Chang-ren; Zhang, Wen-hai; Li, He-song

2017-11-01

The distribution law of materials in smelting products is key to cost accounting and contaminant control. Regardless, the distribution law is difficult to determine quickly and accurately by mere sampling and analysis. Mathematical models for material and heat balance in bottom-blowing smelting, converting, anode furnace refining, and electrolytic refining were established based on the principles of material (element) conservation, energy conservation, and control index constraint in copper bottom-blowing smelting. Simulation of the entire process of bottom-blowing copper smelting was established using a self-developed MetCal software platform. A whole-process simulation for an enterprise in China was then conducted. Results indicated that the quantity and composition information of unknown materials, as well as heat balance information, can be quickly calculated using the model. Comparison of production data revealed that the model can basically reflect the distribution law of the materials in bottom-blowing copper smelting. This finding provides theoretical guidance for mastering the performance of the entire process.

Blow Flies Visiting Decaying Alligators: Is Succession Synchronous or Asynchronous?

OpenAIRE

Nelder, Mark P.; McCreadie, John W.; Major, Clinton S.

2009-01-01

Succession patterns of adult blow flies (Diptera: Calliphoridae) on decaying alligators were investigated in Mobile (Ala, USA) during August 2002. The most abundant blow fly species visiting the carcasses were Chrysomya rufifacies (Macquart), Cochliomyia macellaria (Fabricus), Chrysomya megacephala (Fabricus), Phormia regina (Meigen), and Lucilia coeruleiviridis (Macquart). Lucilia coeruleiviridis was collected more often during the early stages of decomposition, followed by Chrysomya spp., C...

Blowing snow sublimation and transport over Antarctica from 11 years of CALIPSO observations

Directory of Open Access Journals (Sweden)

S. P. Palm

2017-11-01

Full Text Available Blowing snow processes commonly occur over the earth's ice sheets when the 10 m wind speed exceeds a threshold value. These processes play a key role in the sublimation and redistribution of snow thereby influencing the surface mass balance. Prior field studies and modeling results have shown the importance of blowing snow sublimation and transport on the surface mass budget and hydrological cycle of high-latitude regions. For the first time, we present continent-wide estimates of blowing snow sublimation and transport over Antarctica for the period 2006–2016 based on direct observation of blowing snow events. We use an improved version of the blowing snow detection algorithm developed for previous work that uses atmospheric backscatter measurements obtained from the CALIOP (Cloud-Aerosol Lidar with Orthogonal Polarization lidar aboard the CALIPSO (Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observation satellite. The blowing snow events identified by CALIPSO and meteorological fields from MERRA-2 are used to compute the blowing snow sublimation and transport rates. Our results show that maximum sublimation occurs along and slightly inland of the coastline. This is contrary to the observed maximum blowing snow frequency which occurs over the interior. The associated temperature and moisture reanalysis fields likely contribute to the spatial distribution of the maximum sublimation values. However, the spatial pattern of the sublimation rate over Antarctica is consistent with modeling studies and precipitation estimates. Overall, our results show that the 2006–2016 Antarctica average integrated blowing snow sublimation is about 393 ± 196 Gt yr−1, which is considerably larger than previous model-derived estimates. We find maximum blowing snow transport amount of 5 Mt km−1 yr−1 over parts of East Antarctica and estimate that the average snow transport from continent to ocean is about 3.7 Gt yr−1. These

SIKAP, NORMA SUBJEKTIF, DAN INTENSI PEGAWAI NEGERI SIPIL UNTUK MENGADUKAN PELANGGARAN (WHISTLE-BLOWING

Directory of Open Access Journals (Sweden)

Erwan Suryono

2016-06-01

Full Text Available This study aims to investigate factors that influence civil servants to whistle-blow fraud. It also investigates the effect of government’s bureaucracy reforming program on the civil servants’ intention to whistle-blow fraud. By employing the theory of reasoned action, this study included variables of subjective norms, attitudes, and whistle-blowing intentions. This study used primary data gathered from questionnaires of 293 respondents. Respondents were civil servants in the ministries/agencies that have and have not implemented bureaucratic reforms. The findings of this study indicated that subjective norms positively affected the attitudes and intentions of civil servants to report the wrongdoings. However, the attitudes had no significant effect on civil servants’ whistle-blowing intentions. In addition, there are no significant differences on subjective norms, attitudes, and whistle-blowing intentions between civil servants in ministries/agencies that have implemented bureaucratic reforms and civil servants in ministries/agencies that have not implement bureaucratic reforms.

Reduction of airfoil trailing edge noise by trailing edge blowing

International Nuclear Information System (INIS)

Gerhard, T; Carolus, T; Erbslöh, S

2014-01-01

The paper deals with airfoil trailing edge noise and its reduction by trailing edge blowing. A Somers S834 airfoil section which originally was designed for small wind turbines is investigated. To mimic realistic Reynolds numbers the boundary layer is tripped on pressure and suction side. The chordwise position of the blowing slot is varied. The acoustic sources, i.e. the unsteady flow quantities in the turbulent boundary layer in the vicinity of the trailing edge, are quantified for the airfoil without and with trailing edge blowing by means of a large eddy simulation and complementary measurements. Eventually the far field airfoil noise is measured by a two-microphone filtering and correlation and a 40 microphone array technique. Both, LES-prediction and measurements showed that a suitable blowing jet on the airfoil suction side is able to reduce significantly the turbulence intensity and the induced surface pressure fluctuations in the trailing edge region. As a consequence, trailing edge noise associated with a spectral hump around 500 Hz could be reduced by 3 dB. For that a jet velocity of 50% of the free field velocity was sufficient. The most favourable slot position was at 90% chord length

The blow-off mechanism of a bluff-body stabilized laminar premixed flame

KAUST Repository

Kedia, Kushal S.

2015-04-01

© 2014 The Combustion Institute. The objective of this work is to investigate the dynamics leading to blow-off of a laminar premixed flame stabilized on a confined bluff-body using high fidelity numerical simulations. We used unsteady, fully resolved, two-dimensional simulations with detailed chemical kinetics and species transport for methane-air combustion. The flame-wall interaction between the hot reactants and the heat conducting bluff-body was accurately captured by incorporating the conjugate heat exchange between them. Simulations showed a shear-layer stabilized flame just downstream of the bluff-body, with a recirculation zone formed by the products of combustion. The flame was negatively stretched along its entire length, primarily dominated by the normal component of the strain. Blow-off was approached by decreasing the mixture equivalence ratio, at a fixed Reynolds number, of the incoming flow. A flame is stable (does not undergo blow-off) when (1) flame displacement speed is equal to the flow speed and (2) the gradient of the flame displacement speed normal to its surface is higher than the gradient of the flow speed along the same direction. As the equivalence ratio is reduced, the difference between the former and the latter shrinks until the dynamic stability condition (2) is violated, leading to blow-off. Blow-off initiates at a location where this is first violated along the flame. Our results showed that this location was far downstream from the flame anchoring zone, near the end of the recirculation zone. Blow-off started by flame pinching separating the flame into an upstream moving (carried within the recirculation zone) and a downstream convecting (detached from the recirculation zone) flame piece. Within the range of operating conditions investigated, the conjugate heat exchange with the bluff-body had no impact on the flame blow-off.

Description of regional blow-up in a porous-medium equation

Directory of Open Access Journals (Sweden)

Carmen Cortazar

2002-10-01

Full Text Available We describe the (finite-time blow-up phenomenon for a non-negative solution of a porous medium equation of the form $$ u_t = Delta u^m + u^m $$ in the entire space. Here $m>1$ and the initial condition is assumed compactly supported. Blow-up takes place exactly inside a finite number of balls with same radii and exhibiting the same self-similar profile.

Blow-up boundary regimes for general quasilinear parabolic equations in multidimensional domains

International Nuclear Information System (INIS)

Shishkov, A E; Shchelkov, A G

1999-01-01

A new approach (not based on the techniques of barriers) to the study of asymptotic properties of the generalized solutions of parabolic initial boundary-value problems with finite-time blow-up of the boundary values is proposed. Precise conditions on the blow-up pattern are found that guarantee uniform localization of the solution for an arbitrary compactly supported initial function. The main result of the paper consists in obtaining precise sufficient conditions for the singular (or blow-up) set of an arbitrary solution to remain within the boundary of the domain

Prevalence and virulence factors of Candida spp. associated with blow flies

Directory of Open Access Journals (Sweden)

Wimonrat GunTang

2017-05-01

Conclusions: The results indicate that blow flies could play an essential role in the transmission of potentially pathogenic and antifungal resistant C. albicans into the environment. Further investigation on other virulence factors and genetic relatedness among isolates from the blow flies, the environment and clinical specimens is required to confirm this role.

Effects of cathode channel size and operating conditions on the performance of air-blowing PEMFCs

International Nuclear Information System (INIS)

Kim, Bosung; Lee, Yongtaek; Woo, Ahyoung; Kim, Yongchan

2013-01-01

Highlights: • Effect of cathode channel size on the air-blowing PEMFC is analyzed. • Performance and EIS tests of air-blowing PEMFCs are conducted. • Test conditions include the operating temperature, fan voltage, and anode humidity. • Flooding is a limiting factor for decreasing channel size at low temperature. • Water management is investigated by analyzing ohmic resistance. - Abstract: Air-blowing proton exchange membrane fuel cells (PEMFCs) have been developed as a potential new power source for portable electronic devices. However, air-blowing PEMFCs show lower performance than compressed-air PEMFCs because of their adverse operating conditions. In this study, the effects of the cathode channel size and operating conditions on the performance of the air-blowing PEMFC were analyzed. At the normal operating temperature, the performance of the air-blowing PEMFC improved with the decrease in the cathode channel size. However, at a low operating temperature and low fan voltage, massive flooding limits the decrease in the cathode channel size. In addition, water management in the air-blowing PEMFC was investigated by analyzing ohmic resistance. The transition current density between the humidification and the flooding region decreased with decreasing cathode channel size and operating temperature

On-site study of HCFC-22 substitution for HFC non-azeotropic blends (R417A, R422D) on a water chiller of a centralized HVAC system

Energy Technology Data Exchange (ETDEWEB)

Torrella, E.; Larumbe, J.A. [Polytechnic University of Valencia, Dep. of Applied Thermodynamics, Camino de Vera 14, E-46022 Valencia (Spain); Cabello, R.; Sanchez, D.; Llopis, R. [Jaume I University, Dep. of Mechanical Engineering and Construction, Campus de Riu Sec s/n, E-12071 Castellon (Spain)

2010-09-15

The European Regulation no 2037/2000 has banned manufacturing HCFC refrigerants from January 1st 2010, although its use is allowed up to 2015 if the fluids come from a recycling process. This situation creates the need for developing new working fluids to replace the HCFC in the refrigeration plants now in operation. Among all the HCFCs the R22 is the most widely used in a wide range of applications, especially in air conditioning. This work presents an on-site experimental study of the R22 replacement by two possible substitutes, the HFC-417A and the HFC-422D, in a water chiller in which the energy performance was evaluated. This chiller is part of the centralized HVAC system of a lecture room building at the Jaume I University of Castellon, Spain. This communication compares and analyses main operation parameters of the chiller when operating with each refrigerant in real conditions. (author)

The Strong Disjoint Blow-Up/Collapse Property

Directory of Open Access Journals (Sweden)

Héctor N. Salas

2013-01-01

Full Text Available Let be a topological vector space, and let be the algebra of continuous linear operators on . The operators are disjoint hypercyclic if there is such that the orbit is dense in . Bès and Peris have shown that if satisfy the Disjoint Blow-up/Collapse property, then they are disjoint hypercyclic. In a recent paper Bès, Martin, and Sanders, among other things, have characterized disjoint hypercyclic -tuples of weighted shifts in terms of this property. We introduce the Strong Disjoint Blow-up/Collapse property and prove that if satisfy this new property, then they have a dense linear manifold of disjoint hypercyclic vectors. This allows us to give a partial affirmative answer to one of their questions.

First Satellite-detected Perturbations of Outgoing Longwave Radiation Associated with Blowing Snow Events over Antarctica

Science.gov (United States)

Yang, Yuekui; Palm, Stephen P.; Marshak, Alexander; Wu, Dong L.; Yu, Hongbin; Fu, Qiang

2014-01-01

We present the first satellite-detected perturbations of the outgoing longwave radiation (OLR) associated with blowing snow events over the Antarctic ice sheet using data from Cloud-Aerosol Lidar with Orthogonal Polarization and Clouds and the Earth's Radiant Energy System. Significant cloud-free OLR differences are observed between the clear and blowing snow sky, with the sign andmagnitude depending on season and time of the day. During nighttime, OLRs are usually larger when blowing snow is present; the average difference in OLRs between without and with blowing snow over the East Antarctic Ice Sheet is about 5.2 W/m2 for the winter months of 2009. During daytime, in contrast, the OLR perturbation is usually smaller or even has the opposite sign. The observed seasonal variations and day-night differences in the OLR perturbation are consistent with theoretical calculations of the influence of blowing snow on OLR. Detailed atmospheric profiles are needed to quantify the radiative effect of blowing snow from the satellite observations.

Employees’ intention to blow the whistle: The role of fairness and moral identity

Directory of Open Access Journals (Sweden)

Karin Proost, Adríana Pavlinská, Elfi Baillien, Lieven Brebels, Anja Van den Broeck

2013-10-01

Full Text Available In this study we focused on key concepts – moral identity and fairness – in order to explain whistleblowingintention. We examined the relationship between intention to blow the whistle and moral identity, and exploredthe moderating effect of perceived supervisor procedural fairness in this relationship. Our results showed thatemployees (N = 278 with a strong moral identity were more likely to blow the whistle on wrongdoing of whichthey had become aware of, and employees who were low in moral identity were less likely to blow the whistle.Furthermore, we found that the impact of moral identity on the intention to blow the whistle is increased by highprocedural fairness, and that low procedural fairness leaves this relationship insignificant. These findingsrepresent new insights into the study of whistleblowing.

Shooting method for solution of boundary-layer flows with massive blowing

Science.gov (United States)

Liu, T.-M.; Nachtsheim, P. R.

1973-01-01

A modified, bidirectional shooting method is presented for solving boundary-layer equations under conditions of massive blowing. Unlike the conventional shooting method, which is unstable when the blowing rate increases, the proposed method avoids the unstable direction and is capable of solving complex boundary-layer problems involving mass and energy balance on the surface.

Blow-out of nonpremixed turbulent jet flames at sub-atmospheric pressures

KAUST Repository

Wang, Qiang; Hu, Longhua; Chung, Suk-Ho

2016-01-01

Blow-out limits of nonpremixed turbulent jet flames in quiescent air at sub-atmospheric pressures (50–100 kPa) were studied experimentally using propane fuel with nozzle diameters ranging 0.8–4 mm. Results showed that the fuel jet velocity at blow-out limit increased with increasing ambient pressure and nozzle diameter. A Damköhler (Da) number based model was adopted, defined as the ratio of characteristic mixing time and characteristic reaction time, to include the effect of pressure considering the variations in laminar burning velocity and thermal diffusivity with pressure. The critical lift-off height at blow-out, representing a characteristic length scale for mixing, had a linear relationship with the theoretically predicted stoichiometric location along the jet axis, which had a weak dependence on ambient pressure. The characteristic mixing time (critical lift-off height divided by jet velocity) adjusted to the characteristic reaction time such that the critical Damköhler at blow-out conditions maintained a constant value when varying the ambient pressure.

Blow-out of nonpremixed turbulent jet flames at sub-atmospheric pressures

KAUST Repository

Wang, Qiang

2016-12-09

Blow-out limits of nonpremixed turbulent jet flames in quiescent air at sub-atmospheric pressures (50–100 kPa) were studied experimentally using propane fuel with nozzle diameters ranging 0.8–4 mm. Results showed that the fuel jet velocity at blow-out limit increased with increasing ambient pressure and nozzle diameter. A Damköhler (Da) number based model was adopted, defined as the ratio of characteristic mixing time and characteristic reaction time, to include the effect of pressure considering the variations in laminar burning velocity and thermal diffusivity with pressure. The critical lift-off height at blow-out, representing a characteristic length scale for mixing, had a linear relationship with the theoretically predicted stoichiometric location along the jet axis, which had a weak dependence on ambient pressure. The characteristic mixing time (critical lift-off height divided by jet velocity) adjusted to the characteristic reaction time such that the critical Damköhler at blow-out conditions maintained a constant value when varying the ambient pressure.

How does nose blowing effect the computed tomography of paranasal sinuses in chronic sinusitis?

International Nuclear Information System (INIS)

Savranlar, Ahmet; Uzun, Lokman; Ugur, Mehmet Birol; Mahmutyazicioglu, Kamran; Ozer, Tulay; Gundogdu, Sadi

2005-01-01

Objective: Our aim was to determine whether inward or outward movement of the secretions in the paranasal sinuses due to nose blowing after nasal decongestion has any effect on the paranasal sinus computed tomography (CT) images in patients with sinusitis and to asses whether nose blowing may result in misdiagnosis or overdiagnosis in radiological evaluation of sinusitis. Materials and methods: Twenty-four patients with chronic sinusitis were evaluated in an academic tertiary care hospital and data were collected prospectively. After coronal sinus computed tomography scans were performed at 100 mA setting which was half the value of the standard radiation dose suggested by the manufacturer, topical decongestion was applied to each nostril followed by nose blowing 10 min later. Sinus CT scans were then repeated at the same setting. We evaluated the mucosal thickness of medial, lateral, superior and inferior maxillary and frontal sinus walls and the maximal thickness in anterior ethmoidal cells. The measurements prior to and following nose blowing were compared with Wilcoxon signed ranks test. The obtained images were also staged using Lund-McKay staging system separately and the scores were compared with Student's t-test. Results: We observed a tendency towards reduction in mucosal thickness after nose blowing. There were statistically significant differences between maxillary sinus inferior wall and frontal sinus inferior wall mucosal thickness values prior to and after nose blowing. The difference however was very small, about 0.5 mm in magnitude and Lund-McKay score did not change in any of the patients after nose blowing. Conclusion: Nose blowing and topical nasal decongestion does not have any effect on the diagnostic accuracy of sinus CT in chronic sinusitis patients

Control of leading edge vortex breakdown by blowing

Science.gov (United States)

Visser, K. D.; Iwanski, K. P.; Nelson, R. C.; Ng, T. T.

1988-01-01

An investigation into the effects of using a jet of air to control the vortex breakdown position on a 70 degree delta wing is presented. The specific objectives focused on optimizing the blowing positions in terms of maximum lift increments obtained for minimum blowing rates. The tests were conducted at chord Reynolds numbers of 150,000, 200,000, and 250,000 at angles of incidence of 30 and 35 degrees. Visualization and force data is presented to show the effect of the jet on the wing aerodynamic characteristics. The results indicate a jet position located at and aligned parallel to the leading edge to be the optimum. Nearness to the apex and tangency to the upper surface were also crucial factors. The influence of the jet on the leading edge vortex structure was examined using laser Doppler anemometry. Velocity surveys through the vortex showed that at high blowing rates the parallel velocity in the outer swirling region of the vortex increased and the normal velocity decreased. This resulted in a decrease in the swirling angle in the outer region. The peak core velocity was reduced and the vortex breakdown was delayed.

Blow-off of hydrogen using an optimized design of discharge jet-mixer arrangement

International Nuclear Information System (INIS)

Ristow, Torsten

2011-01-01

Hydrogen is ignitable in air at volume concentrations between 4 % and 75 %. Therefore, in the case of an emergency evacuation of a hydrogen-cooled generator in nuclear power plants, the gas has to be safely blown-off above the turbine building. Especially, a leakage at the hydrogen containing piping system at the generator has gained more and more importance in the context of safety assessments. The design of a blow-off system respects two safety aspects: Firstly, a short blow-off time is necessary to reduce the hydrogen release inside the turbine building in case of a leakage. Secondly, for the postulated ignition of the released hydrogen on the roof of the building the resulting pressure load must remain below the maximum admissible one of the turbine building roof. In order to fulfill the first condition an appropriate fast evacuation piping system from the generator to the blow-off outlet is designed. Regarding the latter the blow-off system uses special discharge nozzles placed horizontally in a radial-symmetric configuration. In this respect, the influence of strong wind conditions during the evacuation process is also considered. The resulting ignitable volume of the overlapping H2-air clouds does not exceed the maximum allowed ignitable volume. In the following the underlying process of blow-off by a fast hydrogen evacuation system is discussed. First the transient general blow-off behavior in the dedicated piping system is analyzed with the fluid piping tool ROLAST. The results of these calculations are boundary conditions for the subsequent qualification of the blow-off jet-mixer. Here a proof of the general functionality is given (2D CFD). Subsequently the blow-off behavior of the H2-air mixture is discussed in independent 3D CFD calculations with and without wind. From these analyses the possible ignitable gas volumes are determined. Final step is a simplified semi-analytical assessment of the resulting possible deflagration loads on the civil structure

Blowing-up Semilinear Wave Equation with Exponential ...

Indian Academy of Sciences (India)

Blowing-up Semilinear Wave Equation with Exponential Nonlinearity in Two Space ... We investigate the initial value problem for some semi-linear wave equation in two space dimensions with exponential nonlinearity growth. ... Current Issue

Blow molding electric drives of Mechanical Engineering

Science.gov (United States)

Bukhanov, S. S.; Ramazanov, M. A.; Tsirkunenko, A. T.

2018-03-01

The article considers the questions about the analysis of new possibilities, which gives the use of adjustable electric drives for blowing mechanisms of plastic production. Thus, the use of new semiconductor converters makes it possible not only to compensate the instability of the supply network by using special dynamic voltage regulators, but to improve (correct) the power factor. The calculation of economic efficiency in controlled electric drives of blowing mechanisms is given. On the basis of statistical analysis, the calculation of the reliability parameters of the regulated electric drives’ elements under consideration is given. It is shown that an increase in the reliability of adjustable electric drives is possible both due to overestimation of the electric drive’s installed power, and in simpler schemes with pulse-vector control.

How does nose blowing effect the computed tomography of paranasal sinuses in chronic sinusitis?

Energy Technology Data Exchange (ETDEWEB)

Savranlar, Ahmet; Uzun, Lokman; Ugur, Mehmet Birol; Mahmutyazicioglu, Kamran; Ozer, Tulay; Gundogdu, Sadi

2005-02-01

Objective: Our aim was to determine whether inward or outward movement of the secretions in the paranasal sinuses due to nose blowing after nasal decongestion has any effect on the paranasal sinus computed tomography (CT) images in patients with sinusitis and to asses whether nose blowing may result in misdiagnosis or overdiagnosis in radiological evaluation of sinusitis. Materials and methods: Twenty-four patients with chronic sinusitis were evaluated in an academic tertiary care hospital and data were collected prospectively. After coronal sinus computed tomography scans were performed at 100 mA setting which was half the value of the standard radiation dose suggested by the manufacturer, topical decongestion was applied to each nostril followed by nose blowing 10 min later. Sinus CT scans were then repeated at the same setting. We evaluated the mucosal thickness of medial, lateral, superior and inferior maxillary and frontal sinus walls and the maximal thickness in anterior ethmoidal cells. The measurements prior to and following nose blowing were compared with Wilcoxon signed ranks test. The obtained images were also staged using Lund-McKay staging system separately and the scores were compared with Student's t-test. Results: We observed a tendency towards reduction in mucosal thickness after nose blowing. There were statistically significant differences between maxillary sinus inferior wall and frontal sinus inferior wall mucosal thickness values prior to and after nose blowing. The difference however was very small, about 0.5 mm in magnitude and Lund-McKay score did not change in any of the patients after nose blowing. Conclusion: Nose blowing and topical nasal decongestion does not have any effect on the diagnostic accuracy of sinus CT in chronic sinusitis patients.

Navier-Stokes Computations of a Wing-Flap Model With Blowing Normal to the Flap Surface

Science.gov (United States)

Boyd, D. Douglas, Jr.

2005-01-01

A computational study of a generic wing with a half span flap shows the mean flow effects of several blown flap configurations. The effort compares and contrasts the thin-layer, Reynolds averaged, Navier-Stokes solutions of a baseline wing-flap configuration with configurations that have blowing normal to the flap surface through small slits near the flap side edge. Vorticity contours reveal a dual vortex structure at the flap side edge for all cases. The dual vortex merges into a single vortex at approximately the mid-flap chord location. Upper surface blowing reduces the strength of the merged vortex and moves the vortex away from the upper edge. Lower surface blowing thickens the lower shear layer and weakens the merged vortex, but not as much as upper surface blowing. Side surface blowing forces the lower surface vortex farther outboard of the flap edge by effectively increasing the aerodynamic span of the flap. It is seen that there is no global aerodynamic penalty or benefit from the particular blowing configurations examined.

Asymptotic properties of blow-up solutions in reaction-diffusion equations with nonlocal boundary flux

Science.gov (United States)

Liu, Bingchen; Dong, Mengzhen; Li, Fengjie

2018-04-01

This paper deals with a reaction-diffusion problem with coupled nonlinear inner sources and nonlocal boundary flux. Firstly, we propose the critical exponents on nonsimultaneous blow-up under some conditions on the initial data. Secondly, we combine the scaling technique and the Green's identity method to determine four kinds of simultaneous blow-up rates. Thirdly, the lower and the upper bounds of blow-up time are derived by using Sobolev-type differential inequalities.

Blow-up, Global Existence and Persistence Properties for the Coupled Camassa–Holm equations

International Nuclear Information System (INIS)

Zhu Mingxuan

2011-01-01

In this paper, we consider the coupled Camassa–Holm equations. First, we present some new criteria on blow-up. Then global existence and blow-up rate of the solution are also established. Finally, we discuss persistence properties of this system.

The index of a vector field under blow ups

International Nuclear Information System (INIS)

Seade, J.

1991-08-01

A useful technique when studying the behaviour of holomorphic vector fields around their isolated singularities is that of blowing up the singular points. On the other hand, the most basic invariant of a vector field with isolated singularities is its local index, as defined by Poincare and Hopf. It is thus natural to ask how does the index of a vector field behaves under blowing ups? The purpose of this work is to study and answer this question, by taking a rather general point of view and bearing in mind that complex manifolds have a powerful birational invariant, the Todd genus. 20 refs

Transition between extinction and blow-up in a generalized Fisher–KPP model

Energy Technology Data Exchange (ETDEWEB)

Hernández-Bermejo, Benito, E-mail: benito.hernandez@urjc.es [Departamento de Física, Universidad Rey Juan Carlos, Calle Tulipán S/N, 28933, Móstoles, Madrid (Spain); Sánchez-Valdés, Ariel [Departamento de Matemática Aplicada, Universidad Rey Juan Carlos, Calle Tulipán S/N, 28933, Móstoles, Madrid (Spain)

2014-05-01

Stationary solutions of the Fisher–KPP equation with general nonlinear diffusion and arbitrary reactional kinetic orders terms are characterized. Such stationary (separatrix-like) solutions disjoint the blow-up solutions from those showing extinction. In addition a criterion for general parameter values is presented, which allows determining the blow-up or vanishing character of the solutions.

Transition between extinction and blow-up in a generalized Fisher–KPP model

International Nuclear Information System (INIS)

Hernández-Bermejo, Benito; Sánchez-Valdés, Ariel

2014-01-01

Stationary solutions of the Fisher–KPP equation with general nonlinear diffusion and arbitrary reactional kinetic orders terms are characterized. Such stationary (separatrix-like) solutions disjoint the blow-up solutions from those showing extinction. In addition a criterion for general parameter values is presented, which allows determining the blow-up or vanishing character of the solutions.

Finite-time blow-up for quasilinear degenerate Keller-Segel systems of parabolic-parabolic type

Science.gov (United States)

Hashira, Takahiro; Ishida, Sachiko; Yokota, Tomomi

2018-05-01

This paper deals with the quasilinear degenerate Keller-Segel systems of parabolic-parabolic type in a ball of RN (N ≥ 2). In the case of non-degenerate diffusion, Cieślak-Stinner [3,4] proved that if q > m + 2/N, where m denotes the intensity of diffusion and q denotes the nonlinearity, then there exist initial data such that the corresponding solution blows up in finite time. As to the case of degenerate diffusion, it is known that a solution blows up if q > m + 2/N (see Ishida-Yokota [13]); however, whether the blow-up time is finite or infinite has been unknown. This paper gives an answer to the unsolved problem. Indeed, the finite-time blow-up of energy solutions is established when q > m + 2/N.

Effects of free-stream turbulence intensity and blowing ratio on film cooling of turbine blade leading edge

International Nuclear Information System (INIS)

Kim, S. M.; Kim, Youn J.; Cho, H. H.

2001-01-01

We used a cylindrical model which simulates turbine blade leading edge to investigate the effects of free-stream turbulence intensity and blowing ratio on film cooling of turbine blade leading edge. Tests are carried out in a low-speed wind tunnel on a cylindrical model with three rows of injection holes. Mainstream Reynolds number based on the cylinder diameter was 7.1x10 4 . Two types of turbulence grid are used to increase a free-stream turbulence intensity. The effect of coolant blowing ratio was studied for various blowing ratios. For each blowing ratios, wall temperatures around the surface of the test model are measured by thermocouples installed inside the model. Results show that blowing ratios have small effect on spanwise-averaged film effectiveness at high free-stream turbulence intensity. However, an increase in free-stream turbulence intensity enhances significantly spanwise-averaged film effectiveness at low blowing ratio

The performance of ethics course for increasing students intention to blow the whistle using information technology

Science.gov (United States)

Munandar, Agus

2017-10-01

The profession of accounting believes that ethics is very important in the workplace. For that, profession recommends that ethics course should be taught for accounting student. Unfornutaly, the impact of ethics courses on accounting students intention to blow the whistle on organizational wrongdoing using information technology have not been determined. For that, this paper attempts to measure the impact of ethics courses on accounting student intention to blow the whistle on organizational wrongdoing. The research using experimental design for investigate the impact of ethic course on students intention to blow the whistle using IT. The respondents for this study are 40 accountig students. The respondent were given the ethical scenarios and were measured their intention to blow the whistle using information technology. This result of study reports that 70% of accounting student who completed ethic course indicated high intention to blow the whistle on organizational wrongdoing using information technology. Hence, ethics course is beneficial for increasing accounting professionalism especially their intentio to blow the whistle wrongdoing using information technology.

A Mathematical Model for Reactions During Top-Blowing in the AOD Process: Validation and Results

Science.gov (United States)

Visuri, Ville-Valtteri; Järvinen, Mika; Kärnä, Aki; Sulasalmi, Petri; Heikkinen, Eetu-Pekka; Kupari, Pentti; Fabritius, Timo

2017-06-01

In earlier work, a fundamental mathematical model was proposed for side-blowing operation in the argon oxygen decarburization (AOD) process. In the preceding part "Derivation of the Model," a new mathematical model was proposed for reactions during top-blowing in the AOD process. In this model it was assumed that reactions occur simultaneously at the surface of the cavity caused by the gas jet and at the surface of the metal droplets ejected from the metal bath. This paper presents validation and preliminary results with twelve industrial heats. In the studied heats, the last combined-blowing stage was altered so that oxygen was introduced from the top lance only. Four heats were conducted using an oxygen-nitrogen mixture (1:1), while eight heats were conducted with pure oxygen. Simultaneously, nitrogen or argon gas was blown via tuyères in order to provide mixing that is comparable to regular practice. The measured carbon content varied from 0.4 to 0.5 wt pct before the studied stage to 0.1 to 0.2 wt pct after the studied stage. The results suggest that the model is capable of predicting changes in metal bath composition and temperature with a reasonably high degree of accuracy. The calculations indicate that the top slag may supply oxygen for decarburization during top-blowing. Furthermore, it is postulated that the metal droplets generated by the shear stress of top-blowing create a large mass exchange area, which plays an important role in enabling the high decarburization rates observed during top-blowing in the AOD process. The overall rate of decarburization attributable to top-blowing in the last combined-blowing stage was found to be limited by the mass transfer of dissolved carbon.

Analysis of Tonguing and Blowing Actions During Clarinet Performance.

Science.gov (United States)

Pàmies-Vilà, Montserrat; Hofmann, Alex; Chatziioannou, Vasileios

2018-01-01

Articulation on the clarinet is achieved by a combination of precise actions taking place inside the player's mouth. With the aim to analyse the effects of tonguing and blowing actions during playing, several physical variables are measured and parameters related to articulation are studied. Mouth pressure, mouthpiece pressure and reed displacement are recorded in an experiment with clarinet players to evaluate the influence of the player's actions on the selected parameters and on the sound. The results show that different combinations of tongue and blowing actions are used during performance. Portato and legato playing show constant blowing throughout the musical phrase, which varies according to the dynamic level. In portato, short tongue-reed interaction is used homogeneously among players and playing conditions. In staccato playing, where the tongue-reed contact is longer, the mouth pressure is reduced significantly between notes. Such a mouth-pressure decrease might be used to stop the note in slow staccato playing. It is hereby shown that when the note is stopped by the action of the tongue both the attack and release transients are shorter compared to the case where the vibration of the reed is stopped by a decrease of mouth pressure.

INCOMPRESSIBLE LAMINAR BOUNDARY LAYER CONTROL BY BLOWING AND SUCTION

Directory of Open Access Journals (Sweden)

AZZEDINE NAHOUI

2013-12-01

Full Text Available A two-dimensional incompressible laminar boundary layer and its control using blowing and suction over a flat plate and around the NACA 0012 and 661012 profiles, is studied numerically. The study is based on the Prandtl boundary layer model using the finite differences method and the Crank-Nicolson scheme. The velocity distribution, the boundary layer thickness and the friction coefficient, are determined and presented with and without control. The application of the control technique, has demonstrated its positive effect on the transition point and the friction coefficient. Both control procedures are compared for different lengths, speeds and angles of blowing and suction.

Sex determination mechanisms in the Calliphoridae (blow flies).

Science.gov (United States)

Scott, M J; Pimsler, M L; Tarone, A M

2014-01-01

The Calliphoridae or blow flies are a family of insects that occupy diverse habitats and perform important ecological roles, particularly the decomposition of animal remains. Some Calliphoridae species are also important in the forensic sciences, in agriculture (e.g. as livestock pests) and in medicine (e.g. maggot therapy). Calliphoridae provide striking examples in support of the hypothesis that sex determination regulatory gene hierarchies evolve in the reverse order, with the gene at the top being the most recently added. Unlike the model fly Drosophila melanogaster, where sex is determined by the number of X chromosomes, in the Australian sheep blow fly (Lucilia cuprina) sex is determined by a Y-linked male-determining gene (M). A different regulatory system appears to operate in the hairy maggot blow fly (Chrysomya rufifacies) where the maternal genotype determines sex. It is hypothesized that females heterozygous for a dominant female-determining factor (F/f) produce only female offspring and homozygous f/f females produce only sons. The bottom of the regulatory hierarchy appears to be the same in D. melanogaster and L. cuprina, with sex-specific splicing of doublesex transcripts being controlled by the female-specific Transformer (TRA) protein. We discuss a model that has been proposed for how tra transcripts are sex-specifically spliced in calliphorids, which is very different from D. melanogaster. © 2013 S. Karger AG, Basel.

Blow fly maggots (Diptera: Calliphoridae)from a human corpse in a vehicle.

Science.gov (United States)

Sribanditmongkol, Pongruk; Monum, Tawachai; Wannasan, Anchalee; Tomberlin, Jeffery K; Sukontason, Kom; Sukontason, Kabkaew L

2014-09-01

Correct species identification and development data of insects associated with a cadaver can help estimate the time of colonization which could be used to infer a minimal post-mortem interval (minPMI) for forensic investigations. Human remains are found in a variety of locations ranging from open fields to inside automobiles. We report the investigation of blow fly larvae collected from a decomposing body located in the trunk of a car. There were two blow fly (Diptera: Calliphoridae) species: Achoetandrus rufifacies (Macquart) and Chrysomya megacephala (Fabricius). Blow flies can enter the vehicle and colonize human remains. Based on age estimations of third stage larvae of A. rufifacies, the minPMI was estimated to be 4-5 days, which was within the range of 3-5 days estimated by other forensically relevant information.

Analysis of Tonguing and Blowing Actions During Clarinet Performance

Directory of Open Access Journals (Sweden)

Montserrat Pàmies-Vilà

2018-04-01

Full Text Available Articulation on the clarinet is achieved by a combination of precise actions taking place inside the player's mouth. With the aim to analyse the effects of tonguing and blowing actions during playing, several physical variables are measured and parameters related to articulation are studied. Mouth pressure, mouthpiece pressure and reed displacement are recorded in an experiment with clarinet players to evaluate the influence of the player's actions on the selected parameters and on the sound. The results show that different combinations of tongue and blowing actions are used during performance. Portato and legato playing show constant blowing throughout the musical phrase, which varies according to the dynamic level. In portato, short tongue-reed interaction is used homogeneously among players and playing conditions. In staccato playing, where the tongue-reed contact is longer, the mouth pressure is reduced significantly between notes. Such a mouth-pressure decrease might be used to stop the note in slow staccato playing. It is hereby shown that when the note is stopped by the action of the tongue both the attack and release transients are shorter compared to the case where the vibration of the reed is stopped by a decrease of mouth pressure.

The effect of blow flies (Diptera: Calliphoridae) on the size and weight of mangos (Mangifera indica L.)

Science.gov (United States)

Naqqash, Muhammad Nadir; Saeed, Qamar; Ghouri, Fozia

2016-01-01

Background: Pollination has a great effect on the yield of fruit trees. Blow flies are considered as an effective pollinator compared to hand pollination in fruit orchards. Therefore, this study was designed to evaluate the effect of different pollination methods in mango orchards. Methodology: The impact of pollination on quantity and quality of mango yield by blow flies was estimated by using three treatments, i.e., open pollinated trees, trees were covered by a net in the presence of blow flies for pollination, and trees were covered with a net but without insects. Results: The maximum number of flowers was recorded in irregular types of inflorescence, i.e., 434.80 flowers/inflorescence. Fruit setting (bud) was higher in open pollinated mango trees (i.e. 37.00/inflorescence) than enclosed pollination by blow flies (i.e. 22.34/inflorescence). The size of the mango fruit was the highest (5.06 mm) in open pollinated tree than those pollinated by blow flies (3.93 mm) and followed by without any pollinator (3.18 mm) at marble stage. We found that the maximum weight of mango fruit (201.19 g) was in open pollinated trees. Discussion: The results demonstrated that blow flies can be used as effective mango pollinators along with other flies and bees. The blow flies have shown a positive impact on the quality and quantity of mango. This study will be helpful in future and also applicable at farm level to use blow flies as pollinators that are cheap and easy to rear. PMID:27441107

Cycle Time Optimization of Chamomile Package 120 MI Product at Blow Molding Process

Directory of Open Access Journals (Sweden)

Yuni Hermawan

2012-11-01

Full Text Available Chamomile is a package which is applied for cosmetic. In industry this package is being processed by blow molding. Thereare many parameters that influence cycle time during production; in this project only three of them were varied, i.e. blowingpressure, blowing time and stopping time. Each parameter is determined three chosen level. Middle level is taken fromstandard setting of machining which is being used by industry. Top and bottom level is randomized. Three stopping time are0.1, 0.55, and 1.0 second. Blowing time are 10.5, 11.5 and 12.5 second. Where as, blowing pressures is 4, 5 and 6 bar.Combination of among levels is based on Box Behnken design. Those three parameters are called variable process. In theother hand, variable responses are cycle time and net weight. Each combination is replicated 5 times and then averaged. Thedata then is processed by using Minitab version 14th. Square regression of the model for cycle time is ?CT = 21,1300 - 0,0912X1 + 0,2000 X2 + 0,6313 X3 + 0,6100 X12 + 0,6975 X22 – 0,1000 X1 X2 – 0,1725 X1 X3 + 0,1100 X2 X3 and Net = 19,2933 –0,0088 X1 + 0,0175 X2 + 0,0712 X3 + 0,0133 X 21 + 0.0158 X22- 0.0217 X 23 + 0.0125 X1X2 - 0,0150 X1 X3 for product netweight. Where X1 is blowing pressure, X2 is blowing time and X3 is stopping time.The model developed then tested by lack offit testing, variance by ANOVA and R square. Second stage of model testing is residual test. Three tests are carry out, i.e.identically test and independency test and normality. Optimization of both values, cycle time and net weight, are searched byResponse Surface Method. By the method it is found that the optimum condition of cycle time is 20.5 seconds and net weightis 19.19 grams. The optimum condition is achieved when stopping is 0.1 second, blowing time 11.35 second and blowingpressure 5.1 bars.

Fledging success is a poor indicator of the effects of bird blow flies on ovenbird survival

Science.gov (United States)

Peterson, Sean M.; Streby, Henry M.; Kapfer, Paul M.

2009-01-01

Infestations of bird blow flies (Protocalliphora spp. and Trypocalliphora braueri) have various negative effects on the condition of nestling birds. In the absence of other stressors such as inclement weather, however, infestation alone rarely reduces fledging success. Previous studies have documented effects of blow flies on nestling condition and fledging success. Without information regarding fledgling survival, the full effect of blow-fly infestation remains unclear. To fully investigate the effect of blow-fly infestation on reproductive success of the Ovenbird (Seiurus aurocapilla), we monitored infested and non-infested nests and monitored fledglings from each by using radio telemetry. Blow flies did not affect birds during the nestling period, as brood size, mean nestling mass, fledging success, and time to fledging in infested and non-infested nests were no different. Fledgling survival and minimum distance traveled the first day after fledging, however, were significantly lower for infected fledglings than for those that were not infected. We conclude that the stress of the early fledgling period combined with recent or concurrent blow-fly infection increases mortality in young Oven-birds. Our results demonstrate the importance of including the post-fledging period in investigations of the effects of ectoparasitic infestations on birds.

Computation and measurement of air temperature distribution of an industrial melt blowing die

Directory of Open Access Journals (Sweden)

Wu Li-Li

2014-01-01

Full Text Available The air flow field of the dual slot die on an HDF-6D melt blowing non-woven equipment is computed numerically. A temperature measurement system is built to measure air temperatures. The computation results tally with the measured results proving the correctness of the computation. The results have great valuable significance in the actual melt blowing production.

Local-in-space blow-up criteria for a class of nonlinear dispersive wave equations

Science.gov (United States)

Novruzov, Emil

2017-11-01

This paper is concerned with blow-up phenomena for the nonlinear dispersive wave equation on the real line, ut -uxxt +[ f (u) ] x -[ f (u) ] xxx +[ g (u) + f″/(u) 2 ux2 ] x = 0 that includes the Camassa-Holm equation as well as the hyperelastic-rod wave equation (f (u) = ku2 / 2 and g (u) = (3 - k) u2 / 2) as special cases. We establish some a local-in-space blow-up criterion (i.e., a criterion involving only the properties of the data u0 in a neighborhood of a single point) simplifying and precising earlier blow-up criteria for this equation.

Modeling of Mixing Behavior in a Combined Blowing Steelmaking Converter with a Filter-Based Euler-Lagrange Model

Science.gov (United States)

Li, Mingming; Li, Lin; Li, Qiang; Zou, Zongshu

2018-05-01

A filter-based Euler-Lagrange multiphase flow model is used to study the mixing behavior in a combined blowing steelmaking converter. The Euler-based volume of fluid approach is employed to simulate the top blowing, while the Lagrange-based discrete phase model that embeds the local volume change of rising bubbles for the bottom blowing. A filter-based turbulence method based on the local meshing resolution is proposed aiming to improve the modeling of turbulent eddy viscosities. The model validity is verified through comparison with physical experiments in terms of mixing curves and mixing times. The effects of the bottom gas flow rate on bath flow and mixing behavior are investigated and the inherent reasons for the mixing result are clarified in terms of the characteristics of bottom-blowing plumes, the interaction between plumes and top-blowing jets, and the change of bath flow structure.

Tensile Properties and Fracture Behavior of Aluminum Alloy Foam Fabricated from Die Castings without Using Blowing Agent by Friction Stir Processing Route.

Science.gov (United States)

Hangai, Yoshihiko; Kamada, Hiroto; Utsunomiya, Takao; Kitahara, Soichiro; Kuwazuru, Osamu; Yoshikawa, Nobuhiro

2014-03-21

Al foam has been used in a wide range of applications owing to its light weight, high energy absorption and high sound insulation. One of the promising processes for fabricating Al foam involves the use of a foamable precursor. In this study, ADC12 Al foams with porosities of 67%-78% were fabricated from Al alloy die castings without using a blowing agent by the friction stir processing route. The pore structure and tensile properties of the ADC12 foams were investigated and compared with those of commercially available ALPORAS. From X-ray computed tomography (X-ray CT) observations of the pore structure of ADC12 foams, it was found that they have smaller pores with a narrower distribution than those in ALPORAS. Tensile tests on the ADC12 foams indicated that as their porosity increased, the tensile strength and tensile strain decreased, with strong relation between the porosity, tensile strength, and tensile strain. ADC12 foams exhibited brittle fracture, whereas ALPORAS exhibited ductile fracture, which is due to the nature of the Al alloy used as the base material of the foams. By image-based finite element (FE) analysis using X-ray CT images corresponding to the tensile tests on ADC12 foams, it was shown that the fracture path of ADC12 foams observed in tensile tests and the regions of high stress obtained from FE analysis correspond to each other. Therefore, it is considered that the fracture behavior of ADC12 foams in relation to their pore structure distribution can be investigated by image-based FE analysis.

BLOW.MOD2: program for a vessel depressurization calculation with the contribution of structures

International Nuclear Information System (INIS)

Doval, A.

1990-01-01

The BLOW.MOD2 program developed to calculate pressure vessels' depressurization is presented, considering heat contribution of the structures. The results are opposite to those obtained from other more complex numerical models, being the comparison extremely satisfactory. BLOW.MOD2 is a software of the 'Systems Sub-Branch', INVAP S.E. (Author) [es

Blow-up criteria for the 3D cubic nonlinear Schrödinger equation

International Nuclear Information System (INIS)

Holmer, Justin; Platte, Rodrigo; Roudenko, Svetlana

2010-01-01

We consider solutions u to the 3D nonlinear Schrödinger equation i∂ t u + Δu + |u| 2 u = 0. In particular, we are interested in finding criteria on the initial data u 0 that predict the asymptotic behaviour of u(t), e.g., whether u(t) blows up in finite time, exists globally in time but behaves like a linear solution for large times (scatters), or exists globally in time but does not scatter. This question has been resolved (at least for H 1 data) (Duyckaerts–Holmer–Roudenko) if M[u]E[u] ≤ M[Q]E[Q], where M[u] and E[u] denote the mass and energy of u and Q denotes the ground state solution to −Q + ΔQ + |Q| 2 Q = 0. Here we consider the complementary case M[u]E[u] > M[Q]E[Q]. In the first (analytical) part of the paper, we present a result due to Lushnikov, based on the virial identity and the generalized uncertainty principle, giving a sufficient condition for blow-up. By replacing the uncertainty principle in his argument with an interpolation-type inequality, we obtain a new blow-up condition that in some cases improves upon Lushnikov's condition. Our approach also allows for an adaptation to radial infinite-variance initial data that has a conceptual interpretation: for real-valued initial data, if a certain fraction of the mass is contained within the ball of radius M[u], then blow up occurs. We also show analytically (if one takes the numerically computed value of ||Q|| .H 1/2 ) that there exist Gaussian initial data u 0 with negative quadratic phase such that ||u 0 || .H 1/2 .H 1/2 but the solution u(t) blows up. In the second (numerical) part of the paper, we examine several different classes of initial data—Gaussian, super Gaussian, off-centred Gaussian, and oscillatory Gaussian—and for each class give the theoretical predictions for scattering or blow-up provided by the above theorems as well as the results of numerical simulation. We find that depending upon the form of the initial conditions, any of the three analytical criteria for blow

A multi-agent approach to intelligent monitoring in smart grids

Science.gov (United States)

Vallejo, D.; Albusac, J.; Glez-Morcillo, C.; Castro-Schez, J. J.; Jiménez, L.

2014-04-01

In this paper, we propose a scalable multi-agent architecture to give support to smart grids, paying special attention to the intelligent monitoring of distribution substations. The data gathered by multiple sensors are used by software agents that are responsible for monitoring different aspects or events of interest, such as normal voltage values or unbalanced intensity values that can end up blowing fuses and decreasing the quality of service of end consumers. The knowledge bases of these agents have been built by means of a formal model for normality analysis that has been successfully used in other surveillance domains. The architecture facilitates the integration of new agents and can be easily configured and deployed to monitor different environments. The experiments have been conducted over a power distribution network.

Proteus mirabilis interkingdom swarming signals attract blow flies

Science.gov (United States)

Flies transport specific bacteria with their larvae which provides a wider range of nutrients for those bacteria. Our hypothesis was that this symbiotic interaction may depend on interkingdom signaling. We obtained Proteus mirabilis from the salivary glands of the blow fly Lucilia sericat. This s...

Resection and primary anastomosis with or without modified blow-hole colostomy for sigmoid volvulus

Science.gov (United States)

Coban, Sacid; Yilmaz, Mehmet; Terzi, Alpaslan; Yildiz, Fahrettin; Ozgor, Dincer; Ara, Cengiz; Yologlu, Saim; Kirimlioglu, Vedat

2008-01-01

AIM: To evaluate the efficacy of resection and primary anastomosis (RPA) and RPA with modified blow-hole colostomy for sigmoid volvulus. METHODS: From March 2000 to September 2007, 77 patients with acute sigmoid volvulus were treated. A total of 47 patients underwent RPA or RPA with modified blow-hole colostomy. Twenty-five patients received RPA (Group A), and the remaining 22 patients had RPA with modified blow-hole colostomy (Group B). The clinical course and postoperative complications of the two groups were compared. RESULTS: The mean hospital stay, wound infection and mortality did not differ significantly between the groups. Superficial wound infection rate was higher in group A (32% vs 9.1%). Anastomotic leakage was observed only in group A, with a rate of 6.3%. The difference was numerically impressive but was statistically not significant. CONCLUSION: RPA with modified blow-hole colostomy provides satisfactory results. It is easy to perform and may become a method of choice in patients with sigmoid volvulus. Further studies are required to further establish its role in the treatment of sigmoid volvulus. PMID:18810779

Humidification of Blow-By Oxygen During Recovery of Postoperative Pediatric Patients: One Unit's Journey.

Science.gov (United States)

Donahue, Suzanne; DiBlasi, Robert M; Thomas, Karen

2018-02-02

To examine the practice of nebulizer cool mist blow-by oxygen administered to spontaneously breathing postanesthesia care unit (PACU) pediatric patients during Phase one recovery. Existing evidence was evaluated. Informal benchmarking documented practices in peer organizations. An in vitro study was then conducted to simulate clinical practice and determine depth and amount of airway humidity delivery with blow-by oxygen. Informal benchmarking information was obtained by telephone interview. Using a three-dimensional printed simulation model of the head connected to a breathing lung simulator, depth and amount of moisture delivery in the respiratory tree were measured. Evidence specific to PACU administration of cool mist blow-by oxygen was limited. Informal benchmarking revealed that routine cool mist oxygenated blow-by administration was not widely practiced. The laboratory experiment revealed minimal moisture reaching the mid-tracheal area of the simulated airway model. Routine use of oxygenated cool mist in spontaneously breathing pediatric PACU patients is not supported. Copyright © 2017 American Society of PeriAnesthesia Nurses. Published by Elsevier Inc. All rights reserved.

Clinical investigation of CT-guided ozone-blowing and fumigation ...

African Journals Online (AJOL)

Clinical investigation of CT-guided ozone-blowing and fumigation therapy for the chronic ... African Journal of Biotechnology ... In control group, seven patients were completely cured in 45 days after being treated by traditional surgery.

Blow-up Mechanism of Classical Solutions to Quasilinear Hyperbolic Systems in the Critical Case

Institute of Scientific and Technical Information of China (English)

无

2006-01-01

This paper deals with the blow-up phenomenon, particularly, the geometric blow-up mechanism, of classical solutions to the Cauchy problem for quasilinear hyperbolic systems in the critical case. We prove that it is still the envelope of the same family of characteristics which yields the blowup of classical solutions to the Cauchy problem in the critical case.

Extensive Core Microbiome in Drone-Captured Whale Blow Supports a Framework for Health Monitoring.

Science.gov (United States)

Apprill, Amy; Miller, Carolyn A; Moore, Michael J; Durban, John W; Fearnbach, Holly; Barrett-Lennard, Lance G

2017-01-01

The pulmonary system is a common site for bacterial infections in cetaceans, but very little is known about their respiratory microbiome. We used a small, unmanned hexacopter to collect exhaled breath condensate (blow) from two geographically distinct populations of apparently healthy humpback whales ( Megaptera novaeangliae ), sampled in the Massachusetts coastal waters off Cape Cod ( n = 17) and coastal waters around Vancouver Island ( n = 9). Bacterial and archaeal small-subunit rRNA genes were amplified and sequenced from blow samples, including many of sparse volume, as well as seawater and other controls, to characterize the associated microbial community. The blow microbiomes were distinct from the seawater microbiomes and included 25 phylogenetically diverse bacteria common to all sampled whales. This core assemblage comprised on average 36% of the microbiome, making it one of the more consistent animal microbiomes studied to date. The closest phylogenetic relatives of 20 of these core microbes were previously detected in marine mammals, suggesting that this core microbiome assemblage is specialized for marine mammals and may indicate a healthy, noninfected pulmonary system. Pathogen screening was conducted on the microbiomes at the genus level, which showed that all blow and few seawater microbiomes contained relatives of bacterial pathogens; no known cetacean respiratory pathogens were detected in the blow. Overall, the discovery of a shared large core microbiome in humpback whales is an important advancement for health and disease monitoring of this species and of other large whales. IMPORTANCE The conservation and management of large whales rely in part upon health monitoring of individuals and populations, and methods generally necessitate invasive sampling. Here, we used a small, unmanned hexacopter drone to noninvasively fly above humpback whales from two populations, capture their exhaled breath (blow), and examine the associated microbiome. In the

Tensile Properties and Fracture Behavior of Aluminum Alloy Foam Fabricated from Die Castings without Using Blowing Agent by Friction Stir Processing Route

Directory of Open Access Journals (Sweden)

Yoshihiko Hangai

2014-03-01

Full Text Available Al foam has been used in a wide range of applications owing to its light weight, high energy absorption and high sound insulation. One of the promising processes for fabricating Al foam involves the use of a foamable precursor. In this study, ADC12 Al foams with porosities of 67%–78% were fabricated from Al alloy die castings without using a blowing agent by the friction stir processing route. The pore structure and tensile properties of the ADC12 foams were investigated and compared with those of commercially available ALPORAS. From X-ray computed tomography (X-ray CT observations of the pore structure of ADC12 foams, it was found that they have smaller pores with a narrower distribution than those in ALPORAS. Tensile tests on the ADC12 foams indicated that as their porosity increased, the tensile strength and tensile strain decreased, with strong relation between the porosity, tensile strength, and tensile strain. ADC12 foams exhibited brittle fracture, whereas ALPORAS exhibited ductile fracture, which is due to the nature of the Al alloy used as the base material of the foams. By image-based finite element (FE analysis using X-ray CT images corresponding to the tensile tests on ADC12 foams, it was shown that the fracture path of ADC12 foams observed in tensile tests and the regions of high stress obtained from FE analysis correspond to each other. Therefore, it is considered that the fracture behavior of ADC12 foams in relation to their pore structure distribution can be investigated by image-based FE analysis.

The blow-up problem for a semilinear parabolic equation with a potential

OpenAIRE

Cortazar, C.; Elgueta, M.; Rossi, J. D.

2006-01-01

Let $\\Omega$ be a bounded smooth domain in $\\RR^N$. We consider the problem $u_t= \\Delta u + V(x) u^p$ in $\\Omega \\times [0,T)$, with Dirichlet boundary conditions $u=0$ on $\\partial \\Omega \\times [0,T)$ and initial datum $u(x,0)= M \\phi (x)$ where $M \\geq 0$, $\\phi$ is positive and compatible with the boundary condition. We give estimates for the blow up time of solutions for large values of $M$. As a consequence of these estimates we find that, for $M$ large, the blow up set concentrates ne...

LES-based characterization of a suction and oscillatory blowing fluidic actuator

Science.gov (United States)

Kim, Jeonglae; Moin, Parviz

2015-11-01

Recently, a novel fluidic actuator using steady suction and oscillatory blowing was developed for control of turbulent flows. The suction and oscillatory blowing (SaOB) actuator combines steady suction and pulsed oscillatory blowing into a single device. The actuation is based upon a self-sustained mechanism of confined jets and does not require any moving parts. The control output is determined by a pressure source and the geometric details, and no additional input is needed. While its basic mechanisms have been investigated to some extent, detailed characteristics of internal turbulent flows are not well understood. In this study, internal flows of the SaOB actuator are simulated using large-eddy simulation (LES). Flow characteristics within the actuator are described in detail for a better understanding of the physical mechanisms and improving the actuator design. LES predicts the self-sustained oscillations of the turbulent jet. Switching frequency, maximum velocity at the actuator outlets, and wall pressure distribution are in good agreement with the experimental measurements. The computational results are used to develop simplified boundary conditions for numerical experiments of active flow control. Supported by the Boeing company.

HFC-134A and HCFC-22 supermarket refrigeration demonstration and laboratory testing. Phase I. Final report

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-04-01

Aspen Systems and a team of nineteen agencies and industry participants conducted a series of tests to determine the performance of HFC-134a, HCFC-22, and CFC-502 for supermarket application. This effort constitutes the first phase of a larger project aimed at carrying out both laboratory and demonstration tests of the most viable HFC refrigerants and the refrigerants they replace. The results of the Phase I effort are presented in the present report. The second phase of the project has also been completed. It centered on testing all viable HFC replacement refrigerants for CFC-502. These were HFC-507, HFC-404A, and HFC-407A. The latter results are published in the Phase II report for this project. As part of Phase I, a refrigeration rack utilizing a horizontal open drive screw compressor was constructed in our laboratory. This refrigeration rack is a duplicate of one we have installed in a supermarket in Clifton Park, NY.

Controlled Transverse Blow-up of Highenergy Proton Beams for Aperture Measurements and Loss Maps

CERN Document Server

Hӧfle, W; Redaelli, S; Schmidt, R; Valuch, D; Wollmann, D; Zerlauth, M

2012-01-01

A technique was developed to blow-up transversely in a controlled way high energy proton beams in the LHC. The technique is based on band limited white noise excitation that is injected into the transverse damper feedback loop. The injected signal can be gated to selectively blow-up individual trains of bunches. The speed of transverse blow-up can be precisely controlled. This opens the possibility to perform safely and efficiently aperture measurements and loss maps with high intensity bunch trains well above stored beam energies that are considered to be safe. In particular, lengthy procedures for measurements at top energy, otherwise requiring multiple fills of individual bunches, can be avoided. In this paper, the method is presented and results from beam measurements are discussed and compared with alternative blowup methods.

In vitro antimicrobial activity of solution blow spun poly(lactic acid)/polyvinylpyrrolidone nanofibers loaded with Copaiba (Copaifera sp.) oil

Energy Technology Data Exchange (ETDEWEB)

Bonan, Roberta F. [Departamento de Engenharia de Materiais (DEMAT), Universidade Federal da Paraíba (UFPB), Cidade Universitária, 58.051-900 João Pessoa, PB (Brazil); Centro de Ciências da Saúde (CCS), Universidade Federal da Paraíba (UFPB), Cidade Universitária, 58.051-900 João Pessoa, PB (Brazil); Bonan, Paulo R.F.; Batista, André U.D.; Sampaio, Fábio C.; Albuquerque, Allan J.R. [Centro de Ciências da Saúde (CCS), Universidade Federal da Paraíba (UFPB), Cidade Universitária, 58.051-900 João Pessoa, PB (Brazil); Moraes, Maria C.B. [Embrapa Recursos Genéticos e Biotecnologia, Parque Estação Ecológica, W/5 Norte (Final) Cenargen (Laboratório de Semioquímicos) ASA NORTE, 70770900 Brasília, DF (Brazil); Mattoso, Luiz H.C. [Laboratório Nacional de Nanotecnologia para o Agronegócio (LNNA), Embrapa Instrumentação Agropecuária (CNPDIA), Rua XV de Novembro, 1452, Centro, 13.560, 970 São Carlos, SP (Brazil); Glenn, Gregory M. [United States Department of Agriculture (USDA), Western Regional Research Center (WRRC), Bioproduct Chemistry and Engineering - BCE, Albany, CA 94710 (United States); and others

2015-03-01

In this study poly(lactic acid) (PLA) and polyvinylpyrrolidone (PVP) micro- and nanofiber mats loaded with Copaiba (Copaifera sp.) oil were produced by solution blow spinning (SBS). The Copaiba (Copaifera sp.) oil was characterized by gas chromatography (GC). Neat PLA and four PLA/PVP blends containing 20% (wt.%) oil were spun and characterized by scanning electron microscopy (SEM) and by studying the surface contact angle, in vitro release rate, and antimicrobial activity. All compositions evaluated were able to produce continuous and smooth fibers by SBS. The addition of PVP increased fiber diameter, and decreased the surface contact angle. GC analysis demonstrated that the main component of the Copaiba oil was β-caryophyllene, a known antimicrobial agent. In vitro release tests of Copaiba oil volatiles demonstrated a higher release rate in fibers containing PVP. Fiber mats made from blends containing higher amounts of PVP had greater antimicrobial action against Staphylococcus aureus. The results confirm the potential of the fiber mats for use in controlled drug release and could lead to promising applications in the biomedical field. - Highlights: • An efficient method for production of antimicrobial nanofiber mats using solution blow spinning was reported. • Nanofiber mats containing Copaiba oil were efficient against Staphylococcus aureus. • Nanofiber composition changed morphological properties and antimicrobial action.

Droplet-born air blowing: novel dissolving microneedle fabrication.

Science.gov (United States)

Kim, Jung Dong; Kim, Miroo; Yang, Huisuk; Lee, Kwang; Jung, Hyungil

2013-09-28

The microneedle-mediated drug delivery system has been developed to provide painless self-administration of drugs in a patient-friendly manner. Current dissolving microneedle fabrication methods, however, require harsh conditions for biological drugs and also have problems standardizing the drug dose. Here, we suggested the droplet-born air blowing (DAB) method, which provides gentle (4-25 °C) and fast (≤10min) microneedle fabrication conditions without drug loss. The amount of drug in the microneedle can be controlled by the pressure and time of droplet dispenser and the air blowing shapes this droplet to the microneedle, providing a force sufficient to penetrate skin. Also, the introduction of a base structure of two layered DAB-microneedle could provide complete drug delivery without wasting of drug. The DAB-based insulin loaded microneedle shows similar bioavailability (96.6±2.4%) and down regulation of glucose level compared with subcutaneous injection. We anticipate that DAB described herein will be suitable to design dissolving microneedles for use in biological drug delivery to patients. Copyright © 2013 Elsevier B.V. All rights reserved.

The pattern of fraudulent accounting : Ethics, external auditing and internal whistle-blowing process

Directory of Open Access Journals (Sweden)

Loredana Ferri Di Fabrizio

2017-03-01

Full Text Available The ongoing debate in the literature centres on the compromised auditor’s independence in consequence of the relevant provisions perceived for non-audit services provided to the audited clients. The accounting scandals that have occurred over the past two decades show the lack of competence and independence of external auditors, who kept quite in the face of attempted frauds. The case of Tesco represents an undeniable example of the loss of auditor’s independence, who failed to detect accounting manipulation confirming the importance of whistle-blowing procedures in disclosing concerns before they become serious problems. When turnover occurs in CEOs it is more likely that a rotation in external auditors occurs as well. Finally, changes in top management enable whistle-blowing actions to be successful, interrupting the organization’s dependence on serious wrongdoings and preventing a disastrous ending. The success of whistle-blowing in preventing company failure makes it an effective instrument of сorporate пovernance.

Assessing the stretch-blow moulding FE simulation of PET over a large process window

Science.gov (United States)

Nixon, J.; Menary, G. H.; Yan, S.

2017-10-01

Injection stretch blow moulding has been extensively researched for numerous years and is a well-established method of forming thin-walled containers. This paper is concerned with validating the finite element analysis of the stretch-blow-moulding (SBM) process in an effort to progress the development of injection stretch blow moulding of poly(ethylene terephthalate). Extensive data was obtained experimentally over a wide process window accounting for material temperature, air flow rate and stretch-rod speed while capturing cavity pressure, stretch-rod reaction force, in-mould contact timing and material thickness distribution. This data was then used to assess the accuracy of the correlating FE simulation constructed using ABAQUS/Explicit solver and an appropriate user-defined viscoelastic material subroutine. Results reveal that the simulation was able to pick up the general trends of how the pressure, reaction force and in-mould contact timings vary with the variation in preform temperature and air flow rate. Trends in material thickness were also accurately predicted over the length of the bottle relative to the process conditions. The knowledge gained from these analyses provides insight into the mechanisms of bottle formation, subsequently improving the blow moulding simulation and potentially providing a reduction in production costs.

Quantitative orientational characterization if low - density polyethylene blow films by x-ray and birefringence

International Nuclear Information System (INIS)

Taheri Qazvini, N.; Mohammadi, N.; Ghaffarian, R.; Assempour, H.; Haghighatkish, M.

2002-01-01

The effect of two important parameters of film blowing processes, i.e., take-up ration and blow-up ratio, on the overall orientation of low-density blown films have been investigated using birefringence measurements. Furthermore, by combining x-ray diffraction pole figure analysis and birefringence, the White and Spruiell biaxial orientation functions have been determined for aforementioned sample. Within the range of processing condition studied, increasing take-up ratio, increases orientation in both machine and transverse direction. Upon increasing blow-up ratio, orientation in the transverse direction increases and the overall orientation state approaches to equal biaxial one. Characterization of the crystalline regions by pole figure analysis reveals that a and b crystallographic axes preferentially orientate in the film plane and the direction normal to it, respectively. The amorphous regions do not have any preferential orientation

LHC MD 1087: Controlled Longitudinal Emittance Blow-up with Short Bunches

CERN Document Server

Timko, Helga; Esteban Muller, Juan; Jaussi, Michael; Lasheen, Alexandre; Shaposhnikova, Elena; CERN. Geneva. ATS Department

2017-01-01

The aim of the MD was to study the controlled longitudinal emittance blow-up applied during the ramp with bunches that are slightly shorter than operational. Earlier MDs in 2015 have shown that with a short target bunch length, the blow-up is less controlled and a bifurcation of bunch lengths occurs. The presented measurements show that the bifurcation is independent of the presence of the bunch length feedback, pointing towards an intensity-dependent phenomenon, originating from a synchrotron frequency shift with intensity. Accurate measurements of synchrotron frequency shift with intensity are presented as well. The measurements took place between 22nd August 2016, 19:00 and 23rd August 2016, 04:00.

Oviposition preferences of two forensically important blow fly species, Chrysomya megacephala and C. rufifacies (Diptera: Calliphoridae), and implications for postmortem interval estimation.

Science.gov (United States)

Yang, Shih-Tsai; Shiao, Shiuh-Feng

2012-03-01

Necrophagous blow fly species (Diptera: Calliphoridae) are the most important agents for estimating the postmortem interval (PMI) in forensic entomology. Nevertheless, the oviposition preferences of blow flies may cause a bias of PMI estimations because of a delay or acceleration of egg laying. Chrysomya megacephala (F.) and C. rufifacies (Macquart) are two predominant necrophagous blow fly species in Taiwan. Their larvae undergo rather intense competition, and the latter one can prey on the former under natural conditions. To understand the oviposition preferences of these two species, a dual-choice device was used to test the choice of oviposition sites by females. Results showed when pork liver with and without larvae of C. rufifacies was provided, C. megacephala preferred to lay eggs on the liver without larvae. However, C. megacephala showed no preference when pork liver with and without conspecific larvae or larvae of Hemipyrellia ligurriens (Wiedemann) was provided. These results indicate that females of C. megacephala try to avoid laying eggs around larvae of facultatively predaceous species of C. rufifacies. However, C. rufifacies showed significant oviposition preference for pork liver with larvae of C. megacephala or conspecific ones when compared with pork liver with no larvae. These results probably imply that conspecific larvae or larvae of C. megacephala may potentially be alternative food resources for C. rufifacies, so that its females prefer to lay eggs in their presence. When considering the size of the oviposition media, pork livers of a relatively small size were obviously unfavorable to both species. This may be because females need to find sufficient resources to meet the food demands of their larvae. In another experiment, neither blow fly species showed an oviposition preference for pork livers of different stages of decay. In addition, the oviposition preferences of both species to those media with larvae were greatly disturbed in a dark

On lower bounds for possible blow-up solutions to the periodic Navier-Stokes equation

International Nuclear Information System (INIS)

Cortissoz, Jean C.; Montero, Julio A.; Pinilla, Carlos E.

2014-01-01

We show a new lower bound on the H .3/2 (T 3 ) norm of a possible blow-up solution to the Navier-Stokes equation, and also comment on the extension of this result to the whole space. This estimate can be seen as a natural limiting result for Leray's blow-up estimates in L p (R 3 ), 3 .5/2 (T 3 ), and give the corresponding extension to the case of the whole space

Dolphins Who Blow Bubbles: Anthropological Machines and Native Informants

NARCIS (Netherlands)

Lord, C.

2011-01-01

"Dolphins Who Blow Bubbles: Anthropological Machines and Native Informants" engages a reading between an Oscar winning and now ‘cult’ activist film The Cove (Louise Psihoyos 2009) and classical texts on the human-animal threshold. Giorgio Agamben’s The Open (2002) and Jacques Derrida’s "The Animal

Theoretical studies on the free-blowing process of the vent pipes in the pressure suppression system

International Nuclear Information System (INIS)

Aust, E.

1979-01-01

This report deals with the free-blowing period of the vent pipes in a pressure suppression system, treating especially the analytical simulation of this period. In order to do this the equations presently laid down for use in the computer codes and describing the free-blowing process are presented and their essential model simplifications are worked out. Subsequently, for the simple system of a U-tube filled with water, the fundamental mechanism of the free-blowing process is studied and the results to be transferred from it to the pressure suppression system are discussed. Based on them there are performed calculations with the individual free-blowing models using plant-related parameters as input data, in order to verify in a benchmark comparison the information and the results of calculation of the individual model concepts in relation to one another. Finally the validity of the individual model set-ups and the quality of their predictions are checked by means of experimental results from the pressure suppression experiments on the PSS test stand. (orig.) [de

FE-Analysis of Stretch-Blow Moulded Bottles Using an Integrative Process Simulation

Science.gov (United States)

Hopmann, C.; Michaeli, W.; Rasche, S.

2011-05-01

The two-stage stretch-blow moulding process has been established for the large scale production of high quality PET containers with excellent mechanical and optical properties. The total production costs of a bottle are significantly caused by the material costs. Due to this dominant share of the bottle material, the PET industry is interested in reducing the total production costs by an optimised material efficiency. However, a reduced material inventory means decreasing wall thicknesses and therewith a reduction of the bottle properties (e.g. mechanical properties, barrier properties). Therefore, there is often a trade-off between a minimal bottle weight and adequate properties of the bottle. In order to achieve the objectives Computer Aided Engineering (CAE) techniques can assist the designer of new stretch-blow moulded containers. Hence, tools such as the process simulation and the structural analysis have become important in the blow moulding sector. The Institute of Plastics Processing (IKV) at RWTH Aachen University, Germany, has developed an integrative three-dimensional process simulation which models the complete path of a preform through a stretch-blow moulding machine. At first, the reheating of the preform is calculated by a thermal simulation. Afterwards, the inflation of the preform to a bottle is calculated by finite element analysis (FEA). The results of this step are e.g. the local wall thickness distribution and the local biaxial stretch ratios. Not only the material distribution but also the material properties that result from the deformation history of the polymer have significant influence on the bottle properties. Therefore, a correlation between the material properties and stretch ratios is considered in an integrative simulation approach developed at IKV. The results of the process simulation (wall thickness, stretch ratios) are transferred to a further simulation program and mapped on the bottles FE mesh. This approach allows a local

Ultrastructure of male genitalia of blow flies (Diptera: Calliphoridae) of forensic importance.

Science.gov (United States)

Sontigun, Narin; Sanit, Sangob; Wannasan, Anchalee; Sukontason, Kom; Amendt, Jens; Yasanga, Tippawan; Sukontason, Kabkaew L

2018-03-01

Male genitalia of blow flies (Diptera: Calliphoridae) are distinctive in their morphological features and are often used for species identification. The aim of this work was to investigate the male genitalia of blow flies of medical and forensic importance from Thailand at the ultrastructural level, using scanning electron microscopy (SEM). Flies in two subfamilies were examined: Chrysomyinae [Chrysomya bezziana Villeneuve, Chrysomya chani Kurahashi, Chrysomya nigripes Aubertin, Chrysomya pinguis (Walker), Chrysomya rufifacies (Macquart), Chrysomya thanomthini Kurahashi & Tumrasvin, and Chrysomya villeneuvi Patton] and Luciliinae [Hemipyrellia ligurriens (Wiedemann), Hypopygiopsis infumata (Bigot), Hypopygiopsis tumrasvini Kurahashi, Lucilia cuprina (Wiedemann), Lucilia papuensis Macquart, Lucilia porphyrina (Walker), and Lucilia sinensis Aubertin]. Particular attention was paid to the main distinguishing features such as the shapes of the cercus and the surstylus, and the complex structure of the distiphallus. The differentiation of the male genitalia of these species at the SEM level is discussed and compared to the conditions in closely related species such as Chrysomya megacephala (Fabricius). A key for the identification of 14 blow fly species based on male genitalia is provided. Copyright © 2017 Elsevier B.V. All rights reserved.

The blow-up problem for a semilinear parabolic equation with a potential

Science.gov (United States)

Cortazar, Carmen; Elgueta, Manuel; Rossi, Julio D.

2007-11-01

Let [Omega] be a bounded smooth domain in . We consider the problem ut=[Delta]u+V(x)up in [Omega]×[0,T), with Dirichlet boundary conditions u=0 on [not partial differential][Omega]×[0,T) and initial datum u(x,0)=M[phi](x) where M[greater-or-equal, slanted]0, [phi] is positive and compatible with the boundary condition. We give estimates for the blow-up time of solutions for large values of M. As a consequence of these estimates we find that, for M large, the blow-up set concentrates near the points where [phi]p-1V attains its maximum.

Frequency Response of Near-Wall Coherent Structures to Localized Periodic Blowing and Suction in Turbulent Boundary Layer

International Nuclear Information System (INIS)

Jian-Hua, Liu; Nan, Jiang

2008-01-01

We experimentally investigate the frequency response of near-wall coherent structures to localized periodic blowing and suction through a spanwise slot in a turbulent boundary layer by changing the frequency of periodic disturbance at similar velocities of free stream. The effects of blowing and suction disturbance on energy redistribution, turbulent intensity u' rms + , over y + and waveforms of phase-averaged velocity during sweeping process are respectively discussed under three frequencies of periodic blowing and suction in near-wall region of turbulent boundary layer, compared with those in a standard turbulent boundary layer. The most effective disturbance frequency is figured out in this system. (fundamental areas of phenomenology (including applications))

Blow-Up Analysis for a Quasilinear Degenerate Parabolic Equation with Strongly Nonlinear Source

Directory of Open Access Journals (Sweden)

Pan Zheng

2012-01-01

Full Text Available We investigate the blow-up properties of the positive solution of the Cauchy problem for a quasilinear degenerate parabolic equation with strongly nonlinear source ut=div(|∇um|p−2∇ul+uq,  (x,t∈RN×(0,T, where N≥1, p>2 , and m, l,  q>1, and give a secondary critical exponent on the decay asymptotic behavior of an initial value at infinity for the existence and nonexistence of global solutions of the Cauchy problem. Moreover, under some suitable conditions we prove single-point blow-up for a large class of radial decreasing solutions.

Parameters of the Two-Phase Sand-Air Stream in the Blowing Process

Directory of Open Access Journals (Sweden)

Danko J.

2012-12-01

Full Text Available Theoretical problems concerning the determination of work parameters of the two-phase sand-air stream in the cores making process by blowing methods as well as experimental methods of determination of the main and auxiliary parameters of this process decisive on the cores quality assessed by the value and distribution of their apparent density are presented in the paper. In addition the results of visualisations of the core-box filling with the sand-air stream, from the blowing chamber, obtained by the process filming by means of the quick-action camera are presented in the paper and compared with the results of simulation calculations with the application of the ProCast software.

Thermo-mechanical simulation of liquid-supported stretch blow molding

International Nuclear Information System (INIS)

Zimmer, J.; Stommel, M.

2015-01-01

Stretch blow molding is the well-established plastics forming method to produce Polyehtylene therephtalate (PET) bottles. An injection molded preform is heated up above the PET glass transition temperature (Tg∼85°C) and subsequently inflated by pressurized air into a closed cavity. In the follow-up filling process, the resulting bottle is filled with the final product. A recently developed modification of the process combines the blowing and filling stages by directly using the final liquid product to inflate the preform. In a previously published paper, a mechanical simulation and successful evaluation of this liquid-driven stretch blow molding process was presented. In this way, a realistic process parameter dependent simulation of the preform deformation throughout the forming process was enabled, whereas the preform temperature evolution during forming was neglected. However, the formability of the preform is highly reduced when the temperature sinks below Tg during forming. Experimental investigations show temperature-induced failure cases due to the fast heat transfer between hot preform and cold liquid. Therefore, in this paper, a process dependent simulation of the temperature evolution during processing to avoid preform failure is presented. For this purpose, the previously developed mechanical model is used to extract the time dependent thickness evolution. This information serves as input for the heat transfer simulation. The required material parameters are calibrated from preform cooling experiments recorded with an infrared-camera. Furthermore, the high deformation ratios during processing lead to strain induced crystallization. This exothermal reaction is included into the simulation by extracting data from preform measurements at different stages of deformation via Differential Scanning Calorimetry (DSC). Finally, the thermal simulation model is evaluated by free forming experiments, recorded by a high-speed infrared camera

Numerical Analysis of Film Cooling at High Blowing Ratio

Science.gov (United States)

El-Gabry, Lamyaa; Heidmann, James; Ameri, Ali

2009-01-01

Computational Fluid Dynamics is used in the analysis of a film cooling jet in crossflow. Predictions of film effectiveness are compared with experimental results for a circular jet at blowing ratios ranging from 0.5 to 2.0. Film effectiveness is a surface quantity which alone is insufficient in understanding the source and finding a remedy for shortcomings of the numerical model. Therefore, in addition, comparisons are made to flow field measurements of temperature along the jet centerline. These comparisons show that the CFD model is accurately predicting the extent and trajectory of the film cooling jet; however, there is a lack of agreement in the near-wall region downstream of the film hole. The effects of main stream turbulence conditions, boundary layer thickness, turbulence modeling, and numerical artificial dissipation are evaluated and found to have an insufficient impact in the wake region of separated films (i.e. cannot account for the discrepancy between measured and predicted centerline fluid temperatures). Analyses of low and moderate blowing ratio cases are carried out and results are in good agreement with data.

Occurrence of blowing snow events at an alpine site over a 10-year period: Observations and modelling

Science.gov (United States)

Vionnet, V.; Guyomarc'h, G.; Naaim Bouvet, F.; Martin, E.; Durand, Y.; Bellot, H.; Bel, C.; Puglièse, P.

2013-05-01

Blowing snow events control the evolution of the snow pack in mountainous areas and cause inhomogeneous snow distribution. The goal of this study is to identify the main features of blowing snow events at an alpine site and assess the ability of the detailed snowpack model Crocus to reproduce the occurrence of these events in a 1D configuration. We created a database of blowing snow events observed over 10 years at our experimental site. Occurrences of blowing snow events were divided into cases with and without concurrent falling snow. Overall, snow transport is observed during 10.5% of the time in winter and occurs with concurrent falling snow 37.3% of the time. Wind speed and snow age control the frequency of occurrence. Model results illustrate the necessity of taking the wind-dependence of falling snow grain characteristics into account to simulate periods of snow transport and mass fluxes satisfactorily during those periods. The high rate of false alarms produced by the model is investigated in detail for winter 2010/2011 using measurements from snow particle counters.

Severe diffuse axon injury in chronic alcoholic rat medulla oblongata following a concussion blow.

Science.gov (United States)

Luo, Jianming; Chen, Guang; Wei, Lai; Qian, Hong; Lai, Xiaoping; Wang, Dian; Lv, Junyao; Yu, Xiaojun

2014-01-01

We investigated the axonal morphological changes and expression of both tau protein and β-APP following concussion to the medulla oblongata, in a rat model of chronic alcoholism. Fifty-nine male Sprague-Dawley rats were randomly divided into EtOH, EtOH-TBI and control groups (water group, water-TBI group). To establish chronic alcoholic rats, rats were intragastrically given edible spirituous liquor twice daily. Rats also received a blow on the occipital tuberosity with an iron pendulum. Morphological changes and expression of tau and β-APP proteins in the medulla oblongata were examined. (a) Nerve fibre thickening and twisting were observed in alcoholic rats, with nerve fibre changes becoming more significant following a concussion blow, which leads to some nerve fibres fracturing. (b) Transmission electron microscopy revealed that the nerve fibre myelin became loosened and displayed lamellar separation, which became more significant following concussion. (c) The integral optical density (IOD) sum value of β-APP of the EtOH-TBI group was lower than that in the EtOH group (P Chronic alcoholism caused nerve fibre and neuronal morphology damage in the rat medulla oblongata, with structural damage becoming more significant following concussion. (b) Concussion changed the expression of β-APP and tau protein in chronic alcoholic rat medulla oblongata, suggesting that chronic alcoholism can lead to severe axonal injury following a concussion blow. (c) The effect of chronic alcoholism may be synergistic the concussion blow to promote animal injury and death.

Importance of back blow maneuvers in a 6 month old patient with sudden upper airway obstruction

Directory of Open Access Journals (Sweden)

Pinar Gencpinar

2015-12-01

Full Text Available Foreign body aspiration in children under four years old is one of the most frequently observed reasons for accident related deaths. It is more common in this age group due to inadequate swallowing functions and exploration of objects with the mouth. The most frequently encountered foreign bodies are food and toy parts. Life threatening complete laryngeal obstruction is rarely observed. Dyspnea, hypersalivation, cough and cyanosis can be seen. The basic and life-saving treatment approach is complete removal of foreign body maneuvers in the sudden onset of total obstruction. Here we report a six-month old male, who ingested a foreign body and was treated with back blow maneuvers successfully. In this case we emphasized the importance of back blow maneuvers. Keywords: Upper airway obstruction, Child, Back blows maneuvers

Molecular identification of blow flies recovered from human cadavers during crime scene investigations in Malaysia.

Science.gov (United States)

Kavitha, Rajagopal; Nazni, Wasi Ahmad; Tan, Tian Chye; Lee, Han Lim; Isa, Mohd Noor Mat; Azirun, Mohd Sofian

2012-12-01

Forensic entomology applies knowledge about insects associated with decedent in crime scene investigation. It is possible to calculate a minimum postmortem interval (PMI) by determining the age and species of the oldest blow fly larvae feeding on decedent. This study was conducted in Malaysia to identify maggot specimens collected during crime scene investigations. The usefulness of the molecular and morphological approach in species identifications was evaluated in 10 morphologically identified blow fly larvae sampled from 10 different crime scenes in Malaysia. The molecular identification method involved the sequencing of a total length of 2.2 kilo base pairs encompassing the 'barcode' fragments of the mitochondrial cytochrome oxidase I (COI), cytochrome oxidase II (COII) and t-RNA leucine genes. Phylogenetic analyses confirmed the presence of Chrysomya megacephala, Chrysomya rufifacies and Chrysomya nigripes. In addition, one unidentified blow fly species was found based on phylogenetic tree analysis.

Convection heat transfer of closely-spaced spheres with surface blowing

Energy Technology Data Exchange (ETDEWEB)

Kleinstreuer, C. (North Carolina State Univ., Raleigh, NC (United States). Dept. of Mechanical and Aerospace Engineering); Chiang, H. (Thermofluid Technology Div., Industrial Technology Research Inst., Chutung (Taiwan, Province of China))

1993-05-01

A validated computer simulation model has been developed for the analysis of colinear spheres in a heated gas stream. Using the Galerkin finite element method, the steady-state Navier-Stokes and heat transfer equations have been solved describing laminar axisymmetric thermal flow past closely-spaced monodisperse spheres with fluid injection. Of interest are the coupled nonlinear interaction effects on the temperature fields and ultimately on the Nusselt number of each sphere for different free stream Reynolds numbers (20 [<=] Re [<=] 200) and intersphere distances (1.5 [<=] d[sub ij] [<=] 6.0) in the presence of surface blowing (0 [<=] v[sub b] [<=] 0.1). Fluid injection (i.e. blowing) and associated wake effects generate lower average heat transfer coefficients for each interacting sphere when the Reynolds number increases (Re > 100). Heat transfer is also reduced at small spacings especially for the second and third sphere. A Nusselt number correlation for each interacting (porous) sphere has been developed based on computer experiments. (orig.)

Stefan blowing effect on bioconvective flow of nanofluid over a solid rotating stretchable disk

Directory of Open Access Journals (Sweden)

N.A. Latiff

2016-12-01

Full Text Available A mathematical model for the unsteady forced convection over rotating stretchable disk in nanofluid containing micro-organisms and taking into account Stefan blowing effect is presented theoretically and numerically. Appropriate transformations are used to transform the governing boundary layer equations into non-linear ordinary differential equations, before being solved numerically using the Runge-Kutta-Fehlberg method. The effect of the governing parameters on the dimensionless velocities, temperature, nanoparticle volume fraction (concentration, density of motile microorganisms as well as on the local skin friction, local Nusselt, Sherwood number and motile microorganisms numbers are thoroughly examined via graphs. It is observed that the Stefan blowing increases the local skin friction and reduces the heat transfer, mass transfer and microorganism transfer rates. The numerical results are in good agreement with those obtained from previous literature. Physical quantities results from this investigation show that the effects of higher disk stretching strength and suction case provides a good medium to enhance the heat, mass and microorganisms transfer compared to blowing case.

Blow-up of solutions to the rotation b-family system modeling equatorial water waves

Directory of Open Access Journals (Sweden)

Min Zhu

2018-03-01

Full Text Available We consider the blow-up mechanism to the periodic generalized rotation b-family system (R-b-family system. This model can be derived from the f-plane governing equations for the geographical water waves with a constant underlying current in the equatorial water waves with effect of the Coriolis force. When b=2, it is a rotation two-component Camassa-Holm (R2CH system. We consider the periodic R2CH system when linear dispersion is absent (which model is called r2CH system and derive two finite-time blow-up results.

An electrostatic charge measurement of blowing snow particles focusing on collision frequency to the snow surface

Science.gov (United States)

Omiya, S.; Sato, A.

2010-12-01

Blowing snow particles are known to have an electrostatic charge. This charge may be a contributing factor in the formation of snow drifts and snow cornices and changing of the trajectory of blowing snow particles. These formations and phenomena can cause natural disaster such as an avalanche and a visibility deterioration, and obstruct transportation during winter season. Therefore, charging phenomenon of the blowing snow particles is an important issue in terms of not only precise understanding of the particle motion but disaster prevention. The primary factor of charge accumulation to the blowing snow particles is thought to be due to “saltation” of them. The “saltation” is one of movement forms of blowing snow: when the snow particles are transported by the wind, they repeat frictional collisions with the snow surface. In previous studies, charge-to-mass ratios measured in the field were approximately -50 to -10 μC/kg, and in the wind tunnel were approximately -0.8 to -0.1 μC/kg. While there were qualitatively consistent in sign, negative, there were huge gaps quantitatively between them. One reason of those gaps is speculated to be due to differences in fetch. In other words, the difference of the collision frequency of snow particles to the snow surface has caused the gaps. But it is merely a suggestion and that has not been confirmed. The purpose of this experiment is to measure the charge of blowing snow particles focusing on the collision frequency and clarify the relationship between them. Experiments were carried out in the cryogenic wind tunnel of Snow and Ice Research Center (NIED, JAPAN). A Faraday cage and an electrometer were used to measure the charge of snow particles. These experiments were conducted over the hard snow surface condition to prevent the erosion of the snow surface and the generation of new snow particles from the surface. The collision frequency of particle was controlled by changing the wind velocity (4.5 to 7 m/s) under

Nose micro-blowing for asymmetric vortices control on blunt-nose slender body at high angle of attack

Directory of Open Access Journals (Sweden)

Lei Wang

2017-11-01

Full Text Available The asymmetric vortices over blunt-nose slender body at high angles of attack result in random side force. In this paper, a nose micro-blowing technology is used to control the asymmetric flow. Pressure measurement and particle image velocimetry (PIV experiments are conducted in a low-speed wind tunnel to research effects of jet flow rate on asymmetric vortices over blunt-nose slender body. The angle of attack of the model is fixed at 50° and the Reynolds number for the experiments is 1.6×10 5 based on diameter of aftbody. A blow hole (5 mm in diameter on the nose is processed at circumferential angle θb= 90° and meridian angle γb= 20° with jet momentum ratio Cμ ranging from 5.30×10-7 to 1.19×10−4. Tests are made under two kinds of perturbations. One is called single perturbation with only blow hole and the other is called combined perturbation consists of blow hole and additional granules set on nose. The results show that whether the model has the single perturbation or the combined one, the sectional side force of x/D = 3 varies in the same direction with the increasement of Cμ and remains stable when Cμ is greater than 3.29×10−6. But the stable force values are different according to various perturbations. The fact proves that the size and direction of the side force of blunt-nose slender body can be controlled by the nose micro-blowing.

Hypersonic Boundary Layer Measurements with Variable Blowing Rates Using Molecular Tagging Velocimetry

Science.gov (United States)

Bathel, Brett F.; Danehy, Paul M.; Johansen, Craig T.; Jones, Stephen B.; Goyne, Christopher P.

2012-01-01

Measurements of mean and instantaneous streamwise velocity profiles in a hypersonic boundary layer with variable rates of mass injection (blowing) of nitrogen dioxide (NO2) were obtained over a 10-degree half-angle wedge model. The NO2 was seeded into the flow from a slot located 29.4 mm downstream of the sharp leading edge. The top surface of the wedge was oriented at a 20 degree angle in the Mach 10 flow, yielding an edge Mach number of approximately 4.2. The streamwise velocity profiles and streamwise fluctuating velocity component profiles were obtained using a three-laser NO2->NO photolysis molecular tagging velocimetry method. Observed trends in the mean streamwise velocity profiles and profiles of the fluctuating component of streamwise velocity as functions of the blowing rate are described. An effort is made to distinguish between the effect of blowing rate and wall temperature on the measured profiles. An analysis of the mean velocity profiles for a constant blowing rate is presented to determine the uncertainty in the measurement for different probe laser delay settings. Measurements of streamwise velocity were made to within approximately 120 gm of the model surface. The streamwise spatial resolution in this experiment ranged from 0.6 mm to 2.6 mm. An improvement in the spatial precision of the measurement technique has been made, with spatial uncertainties reduced by about a factor of 2 compared to previous measurements. For the quiescent flow calibration measurements presented, uncertainties as low as 2 m/s are obtained at 95% confidence for long delay times (25 gs). For the velocity measurements obtained with the wind tunnel operating, average single-shot uncertainties of less than 44 m/s are obtained at 95% confidence with a probe laser delay setting of 1 gs. The measurements were performed in the 31-inch Mach 10 Air Tunnel at the NASA Langley Research Center.

Controlled longitudinal emittance blow-up using band-limited phase noise in CERN PSB

Science.gov (United States)

Quartullo, D.; Shaposhnikova, E.; Timko, H.

2017-07-01

Controlled longitudinal emittance blow-up (from 1 eVs to 1.4 eVs) for LHC beams in the CERN PS Booster is currently achievied using sinusoidal phase modulation of a dedicated high-harmonic RF system. In 2021, after the LHC injectors upgrade, 3 eVs should be extracted to the PS. Even if the current method may satisfy the new requirements, it relies on low-power level RF improvements. In this paper another method of blow-up was considered, that is the injection of band-limited phase noise in the main RF system (h=1), never tried in PSB but already used in CERN SPS and LHC, under different conditions (longer cycles). This technique, which lowers the peak line density and therefore the impact of intensity effects in the PSB and the PS, can also be complementary to the present method. The longitudinal space charge, dominant in the PSB, causes significant synchrotron frequency shifts with intensity, and its effect should be taken into account. Another complication arises from the interaction of the phase loop with the injected noise, since both act on the RF phase. All these elements were studied in simulations of the PSB cycle with the BLonD code, and the required blow-up was achieved.

Self-contained anti-static adapter for compressed gas dust blowing devices

International Nuclear Information System (INIS)

Schwartz, L.H.; Miller, S.W.; Severud, C.N. Jr.

1984-01-01

An anti-static adapter which enhances the operation of compressed gas dust blowing devices by allowing the safe use of a radioactive source to ionize a gas stream. The adapter may be used and handled safely without special precautions on the part of the operator

Asymptotic analysis of reaction-diffusion-advection problems: Fronts with periodic motion and blow-up

Science.gov (United States)

Nefedov, Nikolay

2017-02-01

This is an extended variant of the paper presented at MURPHYS-HSFS 2016 conference in Barcelona. We discuss further development of the asymptotic method of differential inequalities to investigate existence and stability of sharp internal layers (fronts) for nonlinear singularly perturbed periodic parabolic problems and initial boundary value problems with blow-up of fronts for reaction-diffusion-advection equations. In particular, we consider periodic solutions with internal layer in the case of balanced reaction. For the initial boundary value problems we prove the existence of fronts and give their asymptotic approximation including the new case of blowing-up fronts. This case we illustrate by the generalised Burgers equation.

10 blows that stopped nuclear power

International Nuclear Information System (INIS)

Komanoff, C.

1991-01-01

The author describes these 10 blows in chronological order, 1973 through 1981, namely: (1) Arab Oil Embargo; (2) India Explodes a Bomb; (3) NRC replaces AEC; (4) Fire at Browns Ferry; (5) General Electric and NRC Engineers switch Sides; (6) Amory Lovins Recasts the Energy Debate; (7) The Seabrook Occupation; (8) The Three Mile Island Accident; (9) Federal Reserve Tightens the Money Supply; and (1) Pacific Gas and Electric Co. Gets it Backwards at Diablo Canyon. he stops there, not including the Washington Public Power Supply fiasco and the Chernobyl disaster, feeling nuclear expansion was essentially foreclosed without them. Further, he feels nuclear power seems fated to be forever at the mercy of forces beyond its control

Oscillation of Vortex Breakdown Location and Blowing Control of Time-Averaged Location

National Research Council Canada - National Science Library

Mitchell, Anthony

2000-01-01

The goal of this research is the control of leading-edge vortex breakdown location utilizing along-the-core blowing near the apex on the leeward surface of sharp-edged, slender, delta wings at high angles of attack...

Species composition of carrion blow flies in northern Thailand: altitude appraisal.

Science.gov (United States)

Moophayak, Kittikhun; Klong-Klaew, Tunwadee; Sukontason, Kom; Kurahashi, Hiromu; Tomberlin, Jeffery K; Sukontason, Kabkaew L

2014-01-01

Distribution and occurrence of blow flies of forensic importance was performed during 2007 and 2008 in Chiang Mai and Lampang Provinces, northern Thailand. Surveys were conducted in forested areas for 30 minutes using a sweep net to collected flies attracted to a bait. A total of 2,115 blow flies belonging to six genera and 14 species were collected; Chrysomya megacephala (Fabricius) (44.7%), C. pinguis (Walker) (15.1%), C. chani Kurahashi (9.3%), C. thanomthini Kurahashi & Tumrasvin (0.3%); Achoetandrus rufifacies (Macquart) (10.5%), A. villeneuvi (Patton) (2.2%); Lucilia papuensis Macquart (2.2%), L. porphyrina (Walker) (12.4%), L. sinensis Aubertin (0.7%); Hemipyrellia ligurriens (Wiedemann) (1.3%), H. pulchra (Wiedemann) (0.1%); Hypopygiopsis infumata (Bigot) (0.6%), Hy. tumrasvini Kurahashi (0.2%) and Ceylonomyia nigripes Aubertin (0.4%). Among them, C. megacephala was the predominant species collected, particularly in the summer. The species likely to prevail in highland areas are C. pinguis, C. thanomthini, Hy. tumrasvini, L. papuensis and L. porphyrina.

SPECIES COMPOSITION OF CARRION BLOW FLIES IN NORTHERN THAILAND: ALTITUDE APPRAISAL

Directory of Open Access Journals (Sweden)

Kittikhun Moophayak

2014-04-01

Full Text Available Distribution and occurrence of blow flies of forensic importance was performed during 2007 and 2008 in Chiang Mai and Lampang Provinces, northern Thailand. Surveys were conducted in forested areas for 30 minutes using a sweep net to collected flies attracted to a bait. A total of 2,115 blow flies belonging to six genera and 14 species were collected; Chrysomya megacephala (Fabricius (44.7%, C. pinguis (Walker (15.1%, C. chani Kurahashi (9.3%, C. thanomthini Kurahashi & Tumrasvin (0.3%; Achoetandrus rufifacies (Macquart (10.5%, A. villeneuvi (Patton (2.2%; Lucilia papuensis Macquart (2.2%, L. porphyrina (Walker (12.4%, L. sinensis Aubertin (0.7%; Hemipyrellia ligurriens(Wiedemann (1.3%, H. pulchra(Wiedemann (0.1%; Hypopygiopsis infumata (Bigot (0.6%, Hy. tumrasvini Kurahashi (0.2% and Ceylonomyia nigripes Aubertin (0.4%. Among them, C. megacephala was the predominant species collected, particularly in the summer. The species likely to prevail in highland areas are C. pinguis, C. thanomthini, Hy. tumrasvini, L. papuensis and L. porphyrina.

Method to reduce arc blow during DC arc welding of pipelines

Energy Technology Data Exchange (ETDEWEB)

Espina-Hernandez, J. H.; Rueda-Morales, G.L.; Caleyo, F.; Hallen, J. M. [Instituto Politecnico Nacional, Mexico, (Mexico); Lopez-Montenegro, A.; Perz-Baruch, E. [Pemex Exploracion y Produccion, Tabasco, (Mexico)

2010-07-01

Steel pipelines are huge ferromagnetic structures and can be easily subjected to arc blow during the DC arc welding process. The development of methods to avoid arc blow during pipeline DC arc welding is a major objective in the pipeline industry. This study developed a simple procedure to compensate the residual magnetic field in the groove during DC arc welding. A Gaussmeter was used to perform magnetic flux density measurements in pipelines in southern Mexico. These data were used to perform magnetic finite element simulations using FEMM. Different variables were studied such as the residual magnetic field in the groove or the position of the coil with respect to the groove. An empirical predictive equation was developed from these trials to compensate for the residual magnetic field. A new method of compensating for the residual magnetic field in the groove by selecting the number of coil turns and the position of the coil with respect to the groove was established.

The blow-off mechanism of a bluff-body stabilized laminar premixed flame

KAUST Repository

Kedia, Kushal S.; Ghoniem, Ahmed F.

2015-01-01

the end of the recirculation zone. Blow-off started by flame pinching separating the flame into an upstream moving (carried within the recirculation zone) and a downstream convecting (detached from the recirculation zone) flame piece. Within the range

Simulation on the Effect of Bottle Wall Thickness Distribution using Blow Moulding Technique

International Nuclear Information System (INIS)

Suraya, S; Azman, M D; Fatchurrohman, N; Jaafar, A A; Yusoff, A R

2016-01-01

The aims of this study are to assess the deformation behavior of a polymeric material during a blow moulding process. Transient computations of two dimensional model of a PP bottle were performed using ANSYS Polyflow computer code to predict the wall thickness distribution at four different parison's diameter; 8mm, 10mm, 18mm, and 20mm. Effects on the final wall thickness diameter and time step are studied. The simulated data shows that the inflation performance degrades with increasing parison diameter. It is concluded that the blow moulding process using 10mm parison successfully meet the product processing requirements. Factors that contribute to the variation in deformation behaviour of the plastic during the manufacturing process are discussed. (paper)

Synthesis of a novel adaptive wavelet optimized neural cascaded steam blow-off control system for a nuclear power plant

International Nuclear Information System (INIS)

Malik, A.H.; Memon, A.A.; Arshad, F.

2013-01-01

Blow-Off System Controller (MIMO AWNN-SBOSC) is designed based on real time dynamic parametric plant data of steam blow-off system with conventional Single-Input Multi-Output Proportional plus Integral plus Derivative Controller (SIMO PIDC). The proposed MIMO AWANN-SBOSC is designed using three Multi-Input Single-Output Adaptive Wavelet Neural Network based Steam Blow-Off System Controllers (MISO AWNN-SBOSC). The hidden layer of each MISO AWNN-SBOSC is formulated using Mother Wavelet Transforms (MWT). Using nonlinear dynamic neural data of designed MIMO AWNN-SBOSC, a Multi-Input Multi-Output Adaptive Wavelet Neural Network based Steam Blow-Off System Model (MIMO AWNN-SBOSM) is developed in cascaded mode. MIMO AWNN-SBOSM is designed using two MISO AWNN-SBOSM. All training, testing and validation of MIMO AWNN-SBOSC and MIMO AWNN-SBOSM are carried out in MA TLAB while all simulation experiments are performed in Visual C. The results of the new design is evaluated against conventional controller based measured data and found robust, fast and much better in performance. (author)

Estimating the Number of Eggs in Blow Fly (Diptera: Calliphoridae) Egg Masses Using Photographic Analysis.

Science.gov (United States)

Rosati, J Y; Pacheco, V A; Vankosky, M A; Vanlaerhoven, S L

2015-07-01

Little work has been done to quantify the number of eggs oviposited by blow flies (Diptera: Calliphoridae) in studies examining colonization behavior. Egg counting methods currently available are time-consuming and destructive. This study used ImageJ software and analysis of covariance to relate the volume of egg masses to the number of eggs laid by three different blow fly species: Lucilia sericata (Meigen), Phormia regina (Meigen), and Chrysomya rufifacies (Macquart). Egg mass volume, species, and the interaction of species and egg mass volume all affected the number of blow fly eggs deposited in egg masses. Both species identity and egg mass volume are important when predicting egg number, as such a single regression equation cannot be used to estimate egg number for these three species. Therefore, simple linear regression equations were determined for each species. The volume of individual eggs was incorporated into the model, yet differences between species were observed, suggesting that the orientation of the eggs oviposited by multiple conspecific females within egg masses influences egg estimates. Based on our results, we expect that imaging software can be used for other blow fly species, as well as other insect species; however, equations specific to each species must be developed. This study describes an important tool for quantifying egg deposition in a nondestructive manner, which is important in studying the colonization behavior and life history of insects of ecological and forensic importance. © The Authors 2015. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Solution blow spun Poly(lactic acid)/Hydroxypropyl methylcellulose nanofibers with antimicrobial properties

Science.gov (United States)

Poly(lactic acid) (PLA) nanofibers containing hydroxypropyl methylcellulose (HPMC) and tetracycline hydrochloride (THC) were solution blow spun from two different solvents, chloroform/acetone (CA, 80:20 v/v) and 2,2,2-triflouroethanol (TFE). The diameter distribution, chemical, thermal, thermal stab...

FEASTING BLACK HOLE BLOWS BUBBLES

Science.gov (United States)

2002-01-01

A monstrous black hole's rude table manners include blowing huge bubbles of hot gas into space. At least, that's the gustatory practice followed by the supermassive black hole residing in the hub of the nearby galaxy NGC 4438. Known as a peculiar galaxy because of its unusual shape, NGC 4438 is in the Virgo Cluster, 50 million light-years from Earth. These NASA Hubble Space Telescope images of the galaxy's central region clearly show one of the bubbles rising from a dark band of dust. The other bubble, emanating from below the dust band, is barely visible, appearing as dim red blobs in the close-up picture of the galaxy's hub (the colorful picture at right). The background image represents a wider view of the galaxy, with the central region defined by the white box. These extremely hot bubbles are caused by the black hole's voracious eating habits. The eating machine is engorging itself with a banquet of material swirling around it in an accretion disk (the white region below the bright bubble). Some of this material is spewed from the disk in opposite directions. Acting like high-powered garden hoses, these twin jets of matter sweep out material in their paths. The jets eventually slam into a wall of dense, slow-moving gas, which is traveling at less than 223,000 mph (360,000 kph). The collision produces the glowing material. The bubbles will continue to expand and will eventually dissipate. Compared with the life of the galaxy, this bubble-blowing phase is a short-lived event. The bubble is much brighter on one side of the galaxy's center because the jet smashed into a denser amount of gas. The brighter bubble is 800 light-years tall and 800 light-years across. The observations are being presented June 5 at the American Astronomical Society meeting in Rochester, N.Y. Both pictures were taken March 24, 1999 with the Wide Field and Planetary Camera 2. False colors were used to enhance the details of the bubbles. The red regions in the picture denote the hot gas

Effect of air-blowing duration on the bond strength of current one-step adhesives to dentin.

Science.gov (United States)

Fu, Jiale; Saikaew, Pipop; Kawano, Shimpei; Carvalho, Ricardo M; Hannig, Matthias; Sano, Hidehiko; Selimovic, Denis

2017-08-01

To evaluate the influence of different air-blowing durations on the micro-tensile bond strength (μTBS) of five current one-step adhesive systems to dentin. One hundred and five caries-free human molars and five current one-step adhesive systems were used: ABU (All Bond Universal, Bisco, Inc.), CUB (CLEARFIL™ Universal Bond, Kuraray), GPB (G-Premio BOND, GC), OBA (OptiBond All-in-one, Kerr) and SBU (Scotchbond Universal, 3M ESPE). The adhesives were applied to 600 SiC paper-flat dentin surfaces according to each manufacturer's instructions and were air-dried with standard, oil-free air pressure of 0.25MPa for either 0s, 5s, 15s or 30s before light-curing. Bond strength to dentin was determined by using μTBS test after 24h of water storage. The fracture pattern on the dentin surface was analyzed by SEM. The resin-dentin interface of untested specimens was visualized by panoramic SEM image. Data from μTBS were analyzed using two-way ANOVA (adhesive vs. air-blowing time), and Games-Howell (a=0.05). Two-way ANOVA revealed a significant effect of materials (p=0.000) and air-blowing time (p=0.000) on bond strength to dentin. The interaction between factors was also significantly different (p=0.000). Maximum bond strength for each system were recorded, OBA/15s (76.34±19.15MPa), SBU/15s (75.18±12.83MPa), CUB/15s (68.23±16.36MPa), GPB/30s (55.82±12.99MPa) and ABU/15s (44.75±8.95MPa). The maximum bond strength of OBA and SUB were significantly higher than that of GPB and ABU (padhesive systems is material-dependent (p=0.000), and was influenced by air-blowing duration (p=0.000). For the current one-step adhesive systems, higher bond strengths could be achieved with prolonged air-blowing duration between 15-30s. Copyright © 2017 The Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Effects of environmental temperature on oviposition behavior in three blow fly species of forensic importance.

Science.gov (United States)

Ody, Helen; Bulling, Mark T; Barnes, Kate M

2017-06-01

A number of factors are known to affect blow fly behavior with respect to oviposition. Current research indicates that temperature is the most significant factor. However temperature thresholds for oviposition in forensically important blow flies have not been well studied. Here, the oviposition behavior of three species of forensically important blow fly species (Calliphora vicina, Calliphora vomitoria and Lucilia sericata,) was studied under controlled laboratory conditions over a range of temperatures (10-40°C). Lower temperature thresholds for oviposition of 16°C and 17.5°C were established for C. vomitoria and L. sericata respectively, whilst C. vicina continued to lay eggs at 10°C. C. vomitoria and L. sericata both continued to lay eggs at 40°C, whilst the highest temperature at which oviposition occurred in C. vicina was 35°C. Within these thresholds there was considerable variation in the number of surviving pupae, with a general pattern of a single peak within the range of temperatures at which eggs were laid, but with the pattern being much less distinct for L. sericata. Copyright © 2017 Elsevier B.V. All rights reserved.

Interferometric measurement of film thickness during bubble blowing

Science.gov (United States)

Wang, Z.; Mandracchia, B.; Ferraro, V.; Tammaro, D.; Di Maio, E.; Maffettone, P. L.; Ferraro, P.

2017-06-01

In this paper, we propose digital holography in transmission configuration as an effective method to measure the time-dependent thickness of polymeric films during bubble blowing. We designed a complete set of experiments to measure bubble thickness, including the evaluation of the refractive index of the polymer solution. We report the measurement of thickness distribution along the film during the bubble formation process until the bubble`s rupture. Based on those data, the variation range and variation trend of bubble film thickness are clearly measured during the process of expansion to fracture is indicated.

INCOMPRESSIBLE LAMINAR BOUNDARY LAYER CONTROL BY BLOWING AND SUCTION

OpenAIRE

AZZEDINE NAHOUI; LAKHDAR BAHI

2013-01-01

A two-dimensional incompressible laminar boundary layer and its control using blowing and suction over a flat plate and around the NACA 0012 and 661012 profiles, is studied numerically. The study is based on the Prandtl boundary layer model using the finite differences method and the Crank-Nicolson scheme. The velocity distribution, the boundary layer thickness and the friction coefficient, are determined and presented with and without control. The application of the control technique, has de...

Blow.MOD2: a program for blowdown transient calculations

International Nuclear Information System (INIS)

Doval, A.

1990-01-01

The BLOW.MOD2 program has been developed to calculate the blowdown phase in a pressurized vessel after a break/valve is opened. It is a one volume model where break height and flow area are specified. Moody critical flow model was adopted under saturation conditions for flow calculation through the break. Heat transfer from structures and internals have been taken into account. Long term depressurization results and a more complex model are compared satisfactorily. (Author)

Blow-up in multidimensional aggregation equations with mildly singular interaction kernels

International Nuclear Information System (INIS)

Bertozzi, Andrea L; Laurent, Thomas; Carrillo, José A

2009-01-01

We consider the multidimensional aggregation equation u t − ∇· (u∇K * u) = 0 in which the radially symmetric attractive interaction kernel has a mild singularity at the origin (Lipschitz or better). In the case of bounded initial data, finite time singularity has been proved for kernels with a Lipschitz point at the origin (Bertozzi and Laurent 2007 Commun. Math. Sci. 274 717–35), whereas for C 2 kernels there is no finite-time blow-up. We prove, under mild monotonicity assumptions on the kernel K, that the Osgood condition for well-posedness of the ODE characteristics determines global in time well-posedness of the PDE with compactly supported bounded nonnegative initial data. When the Osgood condition is violated, we present a new proof of finite time blow-up that extends previous results, requiring radially symmetric data, to general bounded, compactly supported nonnegative initial data without symmetry. We also present a new analysis of radially symmetric solutions under less strict monotonicity conditions. Finally, we conclude with a discussion of similarity solutions for the case K(x) = |x| and some open problems

Flap Gap Oscillatory Blowing on 2D and 2.5D Wing

Directory of Open Access Journals (Sweden)

Cătălin NAE

2009-12-01

Full Text Available Here we present preliminary results obtained in developing an active flow control system for highlift systems at advanced TRL level. The work is based on theoretical and experimental workperformed in AVERT EU FP6 project where the oscillatory flap gap blowing system was designedand tested on a INCAS F15 2D wing model. Pressure data and global loads have been recorded fora complex evaluation of the basic flow control mechanism. In 2.5D test cases this work has beenextended so that the proposed system may be selected as a mature technology in the JTI Clean Sky,Smart Fixed Wing Aircraft ITD. For this goal, new experimental setup was used and also updatedelectronics for the blowing system have been introduces. This was complemented by a newextension for the data acquisition system and visualization tools. Finally global correlations forbasic lift increments have been compared with the reference 2D case and analysed with respect tothe system efficiency.

Low-Speed Wind-Tunnel Investigation of Blowing Boundary-Layer Control on Leading- and Trailing-Edge Flaps of a Large-Scale, Low-Aspect-Ratio, 45 Swept-wing Airplane Configuration

Science.gov (United States)

Maki, Ralph L.

1959-01-01

Blowing boundary-layer control was applied to the leading- and trailing-edge flaps of a 45 deg sweptback-wing complete model in a full-scale low-speed wind-tunnel study. The principal purpose of the study was to determine the effects of leading-edge flap deflection and boundary-layer control on maximum lift and longitudinal stability. Leading-edge flap deflection alone was sufficient to maintain static longitudinal stability without trailing-edge flaps. However, leading-edge flap blowing was required to maintain longitudinal stability by delaying leading-edge flow separation when trailing-edge flaps were deflected either with or without blowing. Partial-span leading-edge flaps deflected 60 deg with moderate blowing gave the major increase in maximum lift, although higher deflection and additional blowing gave some further increase. Inboard of 0.4 semispan leading-edge flap deflection could be reduced to 40 deg and/or blowing could be omitted with only small loss in maximum lift. Trailing-edge flap lift increments were increased by boundary-layer control for deflections greater than 45 deg. Maximum lift was not increased with deflected trailing-edge flaps with blowing.

On wake response to asymmetric blowing in spurts from a blunt ...

Indian Academy of Sciences (India)

tion and generation of noise continue to attract the attention of researchers .... the crest width was maintained as one-fifth of the full cycle, thereby making the blowing .... result in any discernible change in the velocity profile far from the base region, x/h = 5, .... Proceedings of the 44th IEEE Conf. on Decision and Control, and.

Blow-out limits of nonpremixed turbulent jet flames in a cross flow at atmospheric and sub-atmospheric pressures

KAUST Repository

Wang, Qiang

2015-07-22

The blow-out limits of nonpremixed turbulent jet flames in cross flows were studied, especially concerning the effect of ambient pressure, by conducting experiments at atmospheric and sub-atmospheric pressures. The combined effects of air flow and pressure were investigated by a series of experiments conducted in an especially built wind tunnel in Lhasa, a city on the Tibetan plateau where the altitude is 3650 m and the atmospheric pressure condition is naturally low (64 kPa). These results were compared with results obtained from a wind tunnel at standard atmospheric pressure (100 kPa) in Hefei city (altitude 50 m). The size of the fuel nozzles used in the experiments ranged from 3 to 8 mm in diameter and propane was used as the fuel. It was found that the blow-out limit of the air speed of the cross flow first increased (“cross flow dominant” regime) and then decreased (“fuel jet dominant” regime) as the fuel jet velocity increased in both pressures; however, the blow-out limit of the air speed of the cross flow was much lower at sub-atmospheric pressure than that at standard atmospheric pressure whereas the domain of the blow-out limit curve (in a plot of the air speed of the cross flow versus the fuel jet velocity) shrank as the pressure decreased. A theoretical model was developed to characterize the blow-out limit of nonpremixed jet flames in a cross flow based on a Damköhler number, defined as the ratio between the mixing time and the characteristic reaction time. A satisfactory correlation was obtained at relative strong cross flow conditions (“cross flow dominant” regime) that included the effects of the air speed of the cross flow, fuel jet velocity, nozzle diameter and pressure.

What Actions Can Be Taken to Increase Whistle-Blowing in the Classroom?

Science.gov (United States)

Bernardi, Richard A.; Landry, Alexandra C.; Landry, Erynne E.; Buonafede, Mitchell R.; Berardi, Marissa E.

2016-01-01

This study surveyed undergraduate business students on various issues concerning the potential of students whistle-blowing when they observe other students cheating. Developing the courage of one's conviction in our accounting students is important to accounting educators as we are also emphasizing traits such as integrity, skepticism, and…

Thermal large Eddy simulations and experiments in the framework of non-isothermal blowing; Simulations des grandes echelles thermiques et experiences dans le cadre d'effusion anisotherme

Energy Technology Data Exchange (ETDEWEB)

Brillant, G

2004-06-15

The aim of this work is to study thermal large-eddy simulations and to determine the nonisothermal blowing impact on a turbulent boundary layer. An experimental study is also carried out in order to complete and validate simulation results. In a first time, we developed a turbulent inlet condition for the velocity and the temperature, which is necessary for the blowing simulations.We studied the asymptotic behavior of the velocity, the temperature and the thermal turbulent fluxes in a large-eddy simulation point of view. We then considered dynamics models for the eddy-diffusivity and we simulated a turbulent channel flow with imposed temperature, imposed flux and adiabatic walls. The numerical and experimental study of blowing permitted to obtain to the modifications of a thermal turbulent boundary layer with the blowing rate. We observed the consequences of the blowing on mean and rms profiles of velocity and temperature but also on velocity-velocity and velocity-temperature correlations. Moreover, we noticed an increase of the turbulent structures in the boundary layer with blowing. (author)

Whistle-blowing and workplace culture in older peoples' care: qualitative insights from the healthcare and social care workforce.

Science.gov (United States)

Jones, Aled; Kelly, Daniel

2014-09-01

Inquiries in the UK into mistreatment of older people by healthcare employees over the last 30 years have focused on introducing or supporting employee whistle-blowing. Although whistle-blowers have made an important contribution to patient safety it remains a controversial activity. The fate of whistle-blowers is bleak, often resulting in personal and professional sacrifices. Here we draw on the views of healthcare and social care employees working with older people to explore perceptions of whistle-blowing as well as alternative strategies that may be used to raise concerns about the mistreatment of patients by co-workers. Whistle-blowing was perceived as a negative term. Managers said they promoted open cultures underpinned by regular team meetings and an open-door ethos. Others described workplace norms that were somewhat at odds with these open culture ideals. Whistle-blowing was considered risky, and this led to staff creating informal channels through which to raise concerns. Those who witnessed wrongdoing were aware that support was available from external agencies but preferred local solutions and drew upon personal ethics rather than regulatory edicts to shape their responses. We argue that the importance of workplace relationships and informal channels for raising concerns should be better understood to help prevent the mistreatment of vulnerable groups. © 2014 The Authors. Sociology of Health & Illness © 2014 Foundation for the Sociology of Health & Illness/John Wiley & Sons Ltd.

Extraordinary blowing snow transport events in East Antarctica

Energy Technology Data Exchange (ETDEWEB)

Scarchilli, Claudio; Agnoletto, Lucia [ENEA, Rome (Italy); Universita di Siena, Dipartimento di Scienze della Terra, Siena (Italy); Frezzotti, Massimo; Grigioni, Paolo; Silvestri, Lorenzo de [ENEA, Rome (Italy); Dolci, Stefano [CNR, Rome (Italy); Consorzio P.N.R.A. S.C.r.l., Rome (Italy)

2010-06-15

In the convergence slope/coastal areas of Antarctica, a large fraction of snow is continuously eroded and exported by wind to the atmosphere and into the ocean. Snow transport observations from instruments and satellite images were acquired at the wind convergence zone of Terra Nova Bay (East Antarctica) throughout 2006 and 2007. Snow transport features are well-distinguished in satellite images and can extend vertically up to 200 m as first-order quantitatively estimated by driftometer sensor FlowCapt trademark. Maximum snow transportation occurs in the fall and winter seasons. Snow transportation (drift/blowing) was recorded for {proportional_to}80% of the time, and 20% of time recorded, the flux is >10{sup -2} kg m{sup -2} s{sup -1} with particle density increasing with height. Cumulative snow transportation is {proportional_to}4 orders of magnitude higher than snow precipitation at the site. An increase in wind speed and transportation ({proportional_to}30%) was observed in 2007, which is in agreement with a reduction in observed snow accumulation. Extensive presence of ablation surface (blue ice and wind crust) upwind and downwind of the measurement site suggest that the combine processes of blowing snow sublimation and snow transport remove up to 50% of the precipitation in the coastal and slope convergence area. These phenomena represent a major negative effect on the snow accumulation, and they are not sufficiently taken into account in studies of surface mass balance. The observed wind-driven ablation explains the inconsistency between atmospheric model precipitation and measured snow accumulation value. (orig.)

An Evaluation of C1-C3 Hydrochlorofluorocarbon (HCFC) Metrics: Lifetimes, Ozone Depletion Potentials, Radiative Efficiencies, Global Warming and Global Temperature Potentials

Science.gov (United States)

Burkholder, J. B.; Papanastasiou, D. K.; Marshall, P.

2017-12-01

Hydrochlorofluorocarbons (HCFCs) have been used as chlorofluorocarbon (CFC) substitutes in a number of applications, e.g. refrigerator and air-conditioning systems. Although HCFCs have lower ozone-depletion potentials (ODPs) compared to CFCs, they are potent greenhouse gases. The twenty-eighth meeting of the parties to the Montreal Protocol on Substances that Deplete the Ozone Layer (Kigali, 2016) included a list of 274 HCFCs to be controlled under the Montreal Protocol. However, from this list, only 15 of the HCFCs have values for their atmospheric lifetime, ODP, global warming potential (GWP), and global temperature potential (GTP) that are based on fundamental experimental studies, while 48 are registered compounds. In this work, we present a comprehensive evaluation of the atmospheric lifetimes, ODPs, radiative efficiencies (REs), GWPs, and GTPs for all 274 HCFCs to be included in the Montreal Protocol. Atmospheric lifetimes were estimated based on HCFC reactivity with OH radicals and O(1D), as well as their removal by UV photolysis using structure activity relationships and reactivity trends. ODP values are based on the semi-empirical approach described in the WMO/UNEP ozone assessment. Radiative efficiencies were estimated, based on infrared spectra calculated using theoretical electronic structure methods (Gaussian 09). GWPs and GTPs were calculated relative to CO2 using our estimated atmospheric lifetimes and REs. The details of the methodology will be discussed as well as the associated uncertainties. This study has provided a consistent set of atmospheric metrics for a wide range of HCFCs that support future policy decisions. More accurate metrics for a specific HCFC, if desired, would require fundamental laboratory studies to better define the OH reactivity and infrared absorption spectrum of the compound of interest. Overall, HCFCs within the same family (isomers) show a large ODP, GWP, GTP dependence on the molecular geometry of the isomers. The

Determinants and impediments of whistle-blowing in local government councils: A case study of the South-East District Council, Botswana

Directory of Open Access Journals (Sweden)

Abiodun M.T. Omotoye

2017-11-01

Full Text Available This article investigates the perceptions of public service employees regarding the role of whistle-blowing in local government. Whistle-blowing has received increased attention and support as a means of detecting and correcting wrongdoing in organisations. Yet, as this case study discusses, the absence of whistle-blower protection measures and fear of reprisal and job loss deter potential witnesses from reporting wrongdoing in the workplace. A mixed research method approach was employed to undertake the study. A self-administered questionnaire was distributed to public servants employed within the South-East District Council (SEDC and literature related to corruption and whistle-blowing was reviewed. The findings indicate that public service employees strongly support the role whistle-blowing has to play in curbing corruption in the workplace, particularly if the corrupt activity could potentially threaten people’s lives and suppress social justice. However, the absence of whistle-blower protection measures was cited as the most significant impediment to reporting wrongdoing. The article proposes the need for the SEDC to adopt effective policies and procedures that place a strong emphasis on providing protection for employees to disclose misconduct and fraudulent conduct.

Pelletierung von Metallpulvern

OpenAIRE

Hannemann, Christian; Scholz, Steffen

2017-01-01

The method is solving the problem of inhomogeneous blowing agent distribution in precursor fabrication for the metal foam production. The conventional process contains a mixing procedure of metal and blowing agent powders followed by extrusion-compaction resulting in uneven pore sizes and density differences in the finally generated metal foam. Instead the new method coats metal particles with the blowing agent by spray coating, rolling processes or is using pelletizing as in-between step bef...

Finite Element Modeling of Reheat Stretch Blow Molding of PET

Science.gov (United States)

Krishnan, Dwarak; Dupaix, Rebecca B.

2004-06-01

Poly (ethylene terephthalate) or PET is a polymer used as a packaging material for consumer products such as beverages, food or other liquids, and in other applications including drawn fibers and stretched films. Key features that make it widely used are its transparency, dimensional stability, gas impermeability, impact resistance, and high stiffness and strength in certain preferential directions. These commercially useful properties arise from the fact that PET crystallizes upon deformation above the glass transition temperature. Additionally, this strain-induced crystallization causes the deformation behavior of PET to be highly sensitive to processing conditions. It is thus crucial for engineers to be able to predict its performance at various process temperatures, strain rates and strain states so as to optimize the manufacturing process. In addressing these issues; a finite element analysis of the reheat blow molding process with PET has been carried out using ABAQUS. The simulation employed a constitutive model for PET developed by Dupaix and Boyce et al.. The model includes the combined effects of molecular orientation and strain-induced crystallization on strain hardening when the material is deformed above the glass transition temperature. The simulated bottles were also compared with actual blow molded bottles to evaluate the validity of the simulation.

Criteria on global boundedness versus finite time blow-up to a two-species chemotaxis system with two chemicals

Science.gov (United States)

Yu, Hao; Wang, Wei; Zheng, Sining

2018-02-01

This paper considers the two-species chemotaxis system with two chemicals in a smooth bounded domain Ω\\subset{R}2 , subject to the non-flux boundary condition, and χ, ξ, α, β, γ, δ>0 . We obtain a blow-up criterion that if m_1m_2-2π(\\frac{m_1}χβ+\\frac{m_2}ξδ)>0 , then there exist finite time blow-up solutions to the system with m_1:=\\int_Ω u_0(x)dx and m_2:=\\int_Ω w_0(x)dx . When χ=ξ= β=δ=1 , the blow-up criterion becomes m_1m_2-2π(m_1+m_2)>0 , and the global boundedness of solutions is furthermore established with α=γ=1 under the condition that \\max\\{m_1, m_2\\}4π and global boundedness with \\max\\{m_1, m_2\\}Funds for the Central Universities (DUT16LK24).

NAFTA Students'Whistle-blowing Perceptions: A Case of Sexual Harassme

OpenAIRE

Peek, L., M; Roxas, G. Peek; Robichaud, B; Covarrubias; J. Barragan

2005-01-01

Whistle-blowing mechanisms in the U.S. have gained more prominence as an element of legal compliance and antifraud programs. Sexual harassment is a significant business risk in terms of financial costs and the loss of reputation. lt is important for corporations to develop sexual harassment policies and to provide mechanisms for employees toreport sexual harassment behaviors to upper level management. This paper reports on business students' responses to a possible Sexual Harassment scenar...

Development of blow down and sodium-water reaction jet analysis codes-Validation by sodium-water reaction tests (SWAT-1R)

International Nuclear Information System (INIS)

Hiroshi Seino; Akikazu Kurihara; Isao Ono; Koji Jitsu

2005-01-01

Blow down analysis code (LEAP-BLOW) and sodium-water reaction jet analysis code (LEAP-JET) have been developed in order to improve the evaluation method on sodium-water reaction event in the steam generator (SG) of a sodium cooled fast breeder reactor (FBR). The validation analyses by these two codes were carried out using the data of Sodium-Water Reaction Test (SWAT-1R). The following main results have been obtained through this validation: (1) The calculational results by LEAP-BLOW such as internal pressure and water flow rate show good agreement with the results of the SWAT- 1R test. (2) The LEAP-JET code can qualitatively simulate the behavior of sodium-water reaction. However, it is found that the code has tendency to overestimate the maximum temperature of the reaction jet. (authors)

Pattern injuries from blows with the muzzle end of a handgun.

Science.gov (United States)

Geisenberger, D; Vogt, S; Pircher, R; Kramer, L; Pollak, S; Große Perdekamp, M

2015-12-01

Pistols, revolvers and blank guns are not only used to discharge cartridges, but also for hits to the victim. In such cases, the blows preferably affect the head and/or the interposed hands protecting the body. The impact is mostly exerted either by the grip of a pistol or the butt of a revolver. In vigorous thrusts inflicted with the muzzle end of the weapon, the edge of the barrel may produce circular punch lesions with central skin flaps roughly corresponding to the bore. As in other kinds of pistol-whipping, the scalp wounds may be associated with fractures of the skull and even with brain contusions. Using the example of a homicide committed by pistol-whipping, the morphological features of blunt injuries from a handgun's muzzle are presented. The characteristic wound pattern found on the victim's head could be reproduced experimentally by forceful blows to the forehead of a slaughtered pig. In the case presented, the dominant hand of the perpetrator showed friction blisters due to prolonged striking with an unhandy tool in the form of a pistol. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Metabolism of 1-fluoro-1,1,2-trichloroethane, 1,2-dichloro-1,1-difluoroethane, and 1,1,1-trifluoro-2-chloroethane.

Science.gov (United States)

Yin, H; Jones, J P; Anders, M W

1995-03-01

1-Fluoro-1,1,2-trichloroethane (HCFC-131a), 1,2-dichloro-1,1-difluoroethane (HCFC-132b), and 1,1,1-trifluoro-2-chloroethane (HCFC-133a) were chosen as models for comparative metabolism studies on 1,1,1,2-tetrahaloethanes, which are under consideration as replacements for ozone-depleting chlorofluorocarbons (CFCs). Male Fischer 344 rats were given 10 mmol/kg ip HCFC-131a or HCFC-132b or exposed by inhalation to 1% HCFC-133a for 2 h. Urine collected in the first 24 h after exposure was analyzed by 19F NMR and GC/MS and with a fluoride-selective ion electrode for the formation of fluorine-containing metabolites. Metabolites of HCFC-131a included 2,2-dichloro-2-fluoroethyl glucuronide, 2,2-dichloro-2-fluoroethyl sulfate, dichlorofluoroacetic acid, and inorganic fluoride. Metabolites of HCFC-132b were characterized as 2-chloro-2,2-difluoroethyl glucuronide, 2-chloro-2,2-difluoroethyl sulfate, chlorodifluoroacetic acid, chlorodifluoroacetaldehyde hydrate, chlorodifluoroacetaldehyde-urea adduct, and inorganic fluoride. HCFC-133a was metabolized to 2,2,2-trifluoroethyl glucuronide, trifluoroacetic acid, trifluoroacetaldehyde hydrate, trifluoroacetaldehyde-urea adduct, inorganic fluoride, and a minor, unidentified metabolite. With HCFC-131a and HCFC-132b, glucuronide conjugates of 2,2,2-trihaloethanols were the major urinary metabolites, whereas with HCFC-133a, a trifluoroacetaldehyde-urea adduct was the major urinary metabolite. Analysis of metabolite distribution in vivo indicated that aldehydic metabolites increased as fluorine substitution increased in the order HCFC-131a < HCFC-132b < HCFC-133a. With NADPH-fortified rat liver microsomes, HCFC-133a and HCFC-132b were biotransformed to trifluoroacetaldehyde and chlorodifluoroacetaldehyde, respectively, whereas HCFC-131a was converted to dichlorofluoroacetic acid. No covalently bound metabolites were detected by 19F NMR spectroscopy.(ABSTRACT TRUNCATED AT 250 WORDS)

NAFTA Students'Whistle-blowing Perceptions: A Case of Sexual Harassme

Directory of Open Access Journals (Sweden)

Peek, L., M

2005-07-01

Full Text Available Whistle-blowing mechanisms in the U.S. have gained more prominence as an element of legal compliance and antifraud programs. Sexual harassment is a significant business risk in terms of financial costs and the loss of reputation. lt is important for corporations to develop sexual harassment policies and to provide mechanisms for employees toreport sexual harassment behaviors to upper level management. This paper reports on business students' responses to a possible Sexual Harassment scenario from Arthur Andersen's Business Ethics Program and the actions that the characters in the video should take in terms of whistle-blowing. l fall 2004,78 students from two U.S. universities and one Mexican and one Canadian university participated in the prolect as part of the NAFIA Challenges of Accounting and Buslness Sysfems Granf funded by the United States Department of Education Fund for the lmprovement of PostSecondary Education (FIPSE, Human Resources Develópment Canada (HRDC, and Mexico's Secretaría de Educación Pública (SEP. Students from the three NAFTA countries were shown the vignette and asked to respond to a pre-questionnaire concerning the characters' behaviors and possible actions. The students were then asked to discuss the situation and write a reoort from the points of view of the three characters in the vigneite and also to find a copy of an organizations' sexual harassment policy from the Internet. At the end of the project the students responded to a post questionnaire. The students were asked to consider whether the characters should report the possible harasser totheir supervisor, and thus engage in whistle-blowing behavior. Hypotheses are formulated for the three NAFTA'countries based on Hofstede's cultural dimensions and comparisons are made based on overall responses to the pre-and posfquestionnaire. There were significant differences, but in some cases not in the direction expected. Gender differences are also explored, but

MHD Boundary Layer Flow of Dilatant Fluid in a Divergent Channel with Suction or Blowing

International Nuclear Information System (INIS)

Bhattacharyya, Krishnendu; Layek, G. C.

2011-01-01

An analysis is carried out to study a steady magnetohydrodynamic (MHD) boundary layer flow of an electrically conducting incompressible power-law non-Newtonian fluid through a divergent channel. The channel walls are porous and subjected to either suction or blowing of equal magnitude of the same kind of fluid on both walls. The fluid is permeated by a magnetic field produced by electric current along the line of intersection of the channel walls. The governing partial differential equation is transformed into a self-similar nonlinear ordinary differential equation using similarity transformations. The possibility of boundary layer flow in a divergent channel is analyzed with the power-law fluid model. The analysis reveals that the boundary layer flow (without separation) is possible for the case of the dilatant fluid model subjected to suitable suction velocity applied through its porous walls, even in the absence of a magnetic field. Further, it is found that the boundary layer flow is possible even in the presence of blowing for a suitable value of the magnetic parameter. It is found that the velocity increases with increasing values of the power-law index for the case of dilatant fluid. The effects of suction/blowing and magnetic field on the velocity are shown graphically and discussed physically. (fundamental areas of phenomenology(including applications))

Numerical modelling of heat transfer in a cavity due to liquid jet impingement for liquid supported stretch blow moulding

Science.gov (United States)

Smyth, Trevor; Menary, Gary; Geron, Marco

2018-05-01

Impingement of a liquid jet in a polymer cavity has been modelled numerically in this study. Liquid supported stretch blow moulding is a nascent polymer forming process using liquid as the forming medium to produce plastic bottles. The process derives from the conventional stretch blow moulding process which uses compressed air to deform the preform. Heat transfer away from the preform greatly increases when a liquid instead of a gas is flowing over a solid; in the blow moulding process the temperature of the preform is tightly controlled to achieve optimum forming conditions. A model was developed with Computational Fluid Dynamics code ANSYS Fluent which allows the extent of heat transfer between the incoming liquid and the solid preform to be determined in the initial transient stage, where a liquid jet enters an air filled preform. With this data, an approximation of the extent of cooling through the preform wall can be determined.

On blow-up of solutions of the Kuramoto-Sivashinsky equation

International Nuclear Information System (INIS)

Pokhozhaev, S I

2008-01-01

The problem of the absence of global solutions of initial-boundary value problems for the Kuramoto-Sivashinsky equation is considered. Sufficient conditions for the absence of global solutions of the problems under consideration are obtained both for bounded and unbounded domains. These conditions imply a priori the blow-up of the solution of the corresponding initial-boundary value problem. The proof uses a generalization of the method of non-linear capacity based on the choice of asymptotically optimal test functions. Bibliography: 20 titles.

PSB beam longitudinal blow-up by phase modulation with the digital LLRF prototype system

CERN Document Server

Angoletta, M E; Butterworth, A; Findlay, A; Jaussi, M; Leinonen, P; Molendijk, J; Sanchez-Quesada, J

2014-01-01

The PSB will be upgraded to a new, Digital Low-Level RF (DLLRF) system in 2014 at the injectors’ restart after LS1. This DLLRF is an evolution of that successfully deployed in LEIR and comprises new hardware, software and implementation strategies. Machine development studies have been carried out in the PSB over recent years with the existing LEIR-style hardware installed in PSB ring four. These studies have allowed testing approaches and validating implementation strategies. This note focuses on a series of MDs carried out during the 2011 run where a new implementation of the longitudinal beam blow-up obtained by phase modulation was tested. Test results and effects on the beam are show for a CNGS-type beam. Finally, an overview is given of the final longitudinal blow-up implementation planned with the new hardware, which will be operationally deployed in 2014.

Clinical features and MRI findings of blow-out fracture

Energy Technology Data Exchange (ETDEWEB)

Yamanouchi, Yasuo; Yasuda, Takasumi; Kawamoto, Keiji [Kansai Medical Univ., Moriguchi, Osaka (Japan); Inagaki, Takayuki; Someda, Kuniyuki

1996-06-01

Precise anatomical understanding of orbital blow-out fracture lesions is necessary for the treatment of patients. Retrospectively, MRI findings were compared with the clinical features of pure type blow-out fractures and the efficacy of MRI in influencing a decision for surgical intervention was evaluated. Eighteen child (15 boys, 3 girls) cases were evaluated and compared with adult cases. The patients were classified into three categories (Fig.1) and two types (Fig.2) in accordance with the degree of protrusion of fat tissue. The degree of muscle protrusion also was divided into three categories (Fig. 3). Both muscle and fat tissue were protruding from the fracture site in 14 cases. Fat tissue protrusion alone was found in 3 cases. In contrast, no protrusion was seen in one case. The incarcerated type of fat prolapse was found in 40% of cases, while muscle tissue prolapse was found in 75% of patients. Marginal irregularity or swelling of muscle was observed in 11 patients. There was good correlation of ocular motor disturbance and MRI findings. Disturbance of eyeball movement was observed in all patients with either incarcerated fat tissue or marginal irregularity or swelling of muscle. In contrast, restriction of eyeball movement was rare in cases of no incarceration, even if the fracture was wide. Deformity or marginal irregularity of the ocular muscle demonstrated in MRI may suggest damage an adhesion to the muscle wall. When MRI reveals incarceration or severe prolapse of fat tissue, or deformity and marginal irregularity of the ocular muscle, surgical intervention should be considered. (author)

Clinical features and MRI findings of blow-out fracture

International Nuclear Information System (INIS)

Yamanouchi, Yasuo; Yasuda, Takasumi; Kawamoto, Keiji; Inagaki, Takayuki; Someda, Kuniyuki.

1996-01-01

Precise anatomical understanding of orbital blow-out fracture lesions is necessary for the treatment of patients. Retrospectively, MRI findings were compared with the clinical features of pure type blow-out fractures and the efficacy of MRI in influencing a decision for surgical intervention was evaluated. Eighteen child (15 boys, 3 girls) cases were evaluated and compared with adult cases. The patients were classified into three categories (Fig.1) and two types (Fig.2) in accordance with the degree of protrusion of fat tissue. The degree of muscle protrusion also was divided into three categories (Fig. 3). Both muscle and fat tissue were protruding from the fracture site in 14 cases. Fat tissue protrusion alone was found in 3 cases. In contrast, no protrusion was seen in one case. The incarcerated type of fat prolapse was found in 40% of cases, while muscle tissue prolapse was found in 75% of patients. Marginal irregularity or swelling of muscle was observed in 11 patients. There was good correlation of ocular motor disturbance and MRI findings. Disturbance of eyeball movement was observed in all patients with either incarcerated fat tissue or marginal irregularity or swelling of muscle. In contrast, restriction of eyeball movement was rare in cases of no incarceration, even if the fracture was wide. Deformity or marginal irregularity of the ocular muscle demonstrated in MRI may suggest damage an adhesion to the muscle wall. When MRI reveals incarceration or severe prolapse of fat tissue, or deformity and marginal irregularity of the ocular muscle, surgical intervention should be considered. (author)

Bernoulli Suction Effect on Soap Bubble Blowing?

Science.gov (United States)

Davidson, John; Ryu, Sangjin

2015-11-01

As a model system for thin-film bubble with two gas-liquid interfaces, we experimentally investigated the pinch-off of soap bubble blowing. Using the lab-built bubble blower and high-speed videography, we have found that the scaling law exponent of soap bubble pinch-off is 2/3, which is similar to that of soap film bridge. Because air flowed through the decreasing neck of soap film tube, we studied possible Bernoulli suction effect on soap bubble pinch-off by evaluating the Reynolds number of airflow. Image processing was utilized to calculate approximate volume of growing soap film tube and the volume flow rate of the airflow, and the Reynolds number was estimated to be 800-3200. This result suggests that soap bubbling may involve the Bernoulli suction effect.

Estimating total 239240Pu in blow-sand mounds of two safety-shot sites

International Nuclear Information System (INIS)

Gilbert, R.O.; Essington, E.H.

1977-01-01

A study for estimating the total amount (inventory) of 239 240 Pu in blow-sand mounds at two safety-shot sites (Area 13-Project 57 on the Nellis Air Force Base and Clean Slate 3 on the Tonopah Test Range in Nevada) is described. The total amount in blow-sand mounds at these two sites is estimated to be 5.8 +- 1.3 (total +- standard error) and 10.6 +- 2.5 curies, respectively. The total 239 240 Pu in mounds plus desert pavement areas, both to a depth of 5 cm below desert pavement level, is estimated to be 39 +- 5.7 curies at the Project 57 site and 36 +- 4.8 curies at Clean Slate 3. These estimates are compared with the somewhat higher estimates of 46 +- 9 and 37 +- 5.4 curies reported that pertain to only the top 5 cm of mounds and desert pavement. The possibility is discussed that these differences are due to sampling variability arising from the skewed nature of plutonium concentrations, particularly near ground zero

Modeling blowing snow accumulation downwind of an obstruction: The Ohara Eulerian particle distribution equation

Science.gov (United States)

Kinar, N. J.

2017-05-01

An equation was proposed to model the height of blowing snow accumulation downwind of an obstacle such as vegetation, a snow fence, a building, or a topographic feature. The equation does not require aerodynamic flow condition parameters such as wind speed, allowing for the spatial distribution of snow to be determined at locations where meteorological data is not available. However, snow particle diffusion, drift, and erosion coefficients must be estimated for application of the equation. These coefficients can be used to provide insight into the relative magnitude of blowing snow processes at a field location. Further research is required to determine efficient methods for coefficient estimation. The equation could be used with other models of wind-transported snow to predict snow accumulation downwind of an obstacle without the need for wind speed adjustments or correction equations. Applications for this equation include the design of snow fences, and the use of this equation with other hydrological models to predict snow distribution, climate change, drought, flooding, and avalanches.

Intelligent soot blowing for boilers co-firing waste and biofuel; Behovsstyrd sotblaasning foer bio- och avfallseldade pannor - inventering och teknikval

Energy Technology Data Exchange (ETDEWEB)

Kjoerk, Anders [S.E.P. Scandinavian Energy Project AB, Goeteborg (Sweden)

2003-11-01

To achieve optimum boiler operation and performance it is necessary to control the cleanliness and limit the fouling of the heat transfer surfaces. Historically, the heating surfaces in boilers firing biomass and waste are cleaned by steamblowing soot blowers on scheduled time-based and/or parameter-based intervals or by mechanical methods. With the advent of fuel switching strategies and use of mixed-in industrial waste, the control of heating surface cleanliness has become even more crucial for these boilers. Scheduled and/or parameter based approaches do not easily address operational changes. As plant operators push to achieve greater efficiency and performance from their boilers, the ability to more effectively optimize cleaning cycles has become increasingly important. If soot blowing is done only when and where it is required rather than at set intervals, unit performance can be maintained with reduced blowing, which saves steam. Two philosophical approaches toward intelligent soot blowing are currently being applied in the industry. One incorporates heat flux monitors to gather real-time heat transfer data to determine which areas of the furnace need cleaning. The other uses indirect temperature and pressure data to infer locations where soot blowing is needed, and is mainly applied for controlling soot blowers in the superheater and economiser area. The heat flux monitors are so fare used for control of the furnace wall blowers. A system using temperature, pressure and flow data does not require much additional instrumentation as compared with what is available on a standard boiler. However the blower control system must be capable of operating blowers on an individual basis. For advanced options it should also be possible to adjust the speed of the soot blower and the steam pressure. The control program could be more or less advanced but the ability to model heating surfaces and determine real-time cleanliness is crucial for an intelligent soot blowing

Blow/trauma to the chest and sudden cardiac death: Commotio cordis and contusio cordis are leading causes.

Science.gov (United States)

Krexi, Lydia; Sheppard, Mary N

2018-01-01

Background In forensic practice, a blow to the chest can lead to sudden cardiac death (SCD). Commotio cordis and contusio cordis are leading causes. Methods From a database of 4678 patients who suffered from SCD, we found three patients with commotio cordis and two patients with contusio cordis. All the patients were examined macroscopically and microscopically and had negative toxicology screen. Results The three patients who died due to commotio cordis were young males (16, 23 and 38 years old). The circumstances of death were: a blow to the chest by a football, by a friend during a party and during an assault. The hearts were completely normal at autopsy. The two patients who had contusio cordis were older males (42 and 63 years old). Both patients died during traffic accidents. At autopsy, one had significant contusion over the left ventricle, and the second had contusion over the right ventricle. Conclusion This study indicates that a blow to the chest is very important to document in the circumstances of death, and a detailed history is vital. It raises the left ventricular intra-cavitary pressure, leading to commotio cordis with immediate death with a normal heart. Blunt chest trauma can cause direct myocardial lesions, with acute changes leading to contusio cordis.

Gene expression during blow fly development: improving the precision of age estimates in forensic entomology.

Science.gov (United States)

Tarone, Aaron M; Foran, David R

2011-01-01

Forensic entomologists use size and developmental stage to estimate blow fly age, and from those, a postmortem interval. Since such estimates are generally accurate but often lack precision, particularly in the older developmental stages, alternative aging methods would be advantageous. Presented here is a means of incorporating developmentally regulated gene expression levels into traditional stage and size data, with a goal of more precisely estimating developmental age of immature Lucilia sericata. Generalized additive models of development showed improved statistical support compared to models that did not include gene expression data, resulting in an increase in estimate precision, especially for postfeeding third instars and pupae. The models were then used to make blind estimates of development for 86 immature L. sericata raised on rat carcasses. Overall, inclusion of gene expression data resulted in increased precision in aging blow flies. © 2010 American Academy of Forensic Sciences.

Exploring Hydrofluorocarbons as Groundwater Age Tracers (Invited)

Science.gov (United States)

Haase, K. B.; Busenberg, E.; Plummer, L. N.; Casile, G.; Sanford, W. E.

2013-12-01

refrigerant introduced in the 1940's, with atmospheric mixing ratios increasing through the 1990s to the present value of ≈230 pptv. HFC-134a is typically is used as a chlorine-free replacement for CFC-12, finding use in air-condition systems and as an inert aerosol blowing agent, with a mixing ratio that has increased from water, and blanks suggests the GC-AED system is capable of detecting concentrations ≈200 fM (HCFC-22) and ≈100 fM (HFC-134a), corresponding to piston flow ages of 54 and 18 yr, respectively, with a typical uncertainty of ≈1 yr. Preliminary comparisons with CFC and SF6 analyses show general agreement between the techniques (within a few years), and ongoing intercomparison studies will be discussed.

Blow-up of the quantum potential for a free particle in one dimension

International Nuclear Information System (INIS)

Devillanova, G.; Maddalena, F.; Florio, G.

2013-01-01

We derive a non-linear differential equation that must be satisfied by the quantum potential, in the context of the Madelung equations, in one dimension for a particular class of wave functions. In this case, we exhibit explicit conditions leading to the blow-up of the quantum potential of a free particle at the boundary of the compact support of the probability density.

Control of Flow Structure on Non-Slender Delta Wing: Bio-inspired Edge Modifications, Passive Bleeding, and Pulsed Blowing

Science.gov (United States)

Yavuz, Mehmet Metin; Celik, Alper; Cetin, Cenk

2016-11-01

In the present study, different flow control approaches including bio-inspired edge modifications, passive bleeding, and pulsed blowing are introduced and applied for the flow over non-slender delta wing. Experiments are conducted in a low speed wind tunnel for a 45 degree swept delta wing using qualitative and quantitative measurement techniques including laser illuminated smoke visualization, particle image velocimety (PIV), and surface pressure measurements. For the bio-inspired edge modifications, the edges of the wing are modified to dolphin fluke geometry. In addition, the concept of flexion ratio, a ratio depending on the flexible length of animal propulsors such as wings, is introduced. For passive bleeding, directing the free stream air from the pressure side of the planform to the suction side of the wing is applied. For pulsed blowing, periodic air injection through the leading edge of the wing is performed in a square waveform with 25% duty cycle at different excitation frequencies and compared with the steady and no blowing cases. The results indicate that each control approach is quite effective in terms of altering the overall flow structure on the planform. However, the success level, considering the elimination of stall or delaying the vortex breakdown, depends on the parameters in each method.

Preparation of Fish Skin Gelatin-Based Nanofibers Incorporating Cinnamaldehyde by Solution Blow Spinning

Science.gov (United States)

Liu, Fei; Avena-Bustillos, Roberto J.; Bridges, David F.; Takeoka, Gary R.; Wu, Vivian C. H.; Chiou, Bor-Sen; McHugh, Tara H.; Zhong, Fang

2018-01-01

Cinnamaldehyde, a natural preservative that can non-specifically deactivate foodborne pathogens, was successfully incorporated into fish skin gelatin (FSG) solutions and blow spun into uniform nanofibers. The effects of cinnamaldehyde ratios (5–30%, w/w FSG) on physicochemical properties of fiber-forming emulsions (FFEs) and their nanofibers were investigated. Higher ratios resulted in higher values in particle size and viscosity of FFEs, as well as higher values in diameter of nanofibers. Loss of cinnamaldehyde was observed during solution blow spinning (SBS) process and cinnamaldehyde was mainly located on the surface of resultant nanofibers. Nanofibers all showed antibacterial activity by direct diffusion and vapor release against Escherichia coli O157:H7, Salmonella typhimurium, and Listeria monocytogenes. Inhibition zones increased as cinnamaldehyde ratio increased. Nanofibers showed larger inhibition effects than films prepared by casting method when S. typhimurium was exposed to the released cinnamaldehyde vapor, although films had higher remaining cinnamaldehyde than nanofibers after preparation. Lower temperature was favorable for cinnamaldehyde retention, and nanofibers added with 10% cinnamaldehyde ratio showed the highest retention over eight-weeks of storage. Results suggest that FSG nanofibers can be prepared by SBS as carriers for antimicrobials. PMID:29470390

Preparation of Fish Skin Gelatin-Based Nanofibers Incorporating Cinnamaldehyde by Solution Blow Spinning.

Science.gov (United States)

Liu, Fei; Türker Saricaoglu, Furkan; Avena-Bustillos, Roberto J; Bridges, David F; Takeoka, Gary R; Wu, Vivian C H; Chiou, Bor-Sen; Wood, Delilah F; McHugh, Tara H; Zhong, Fang

2018-02-22

Cinnamaldehyde, a natural preservative that can non-specifically deactivate foodborne pathogens, was successfully incorporated into fish skin gelatin (FSG) solutions and blow spun into uniform nanofibers. The effects of cinnamaldehyde ratios (5-30%, w / w FSG) on physicochemical properties of fiber-forming emulsions (FFEs) and their nanofibers were investigated. Higher ratios resulted in higher values in particle size and viscosity of FFEs, as well as higher values in diameter of nanofibers. Loss of cinnamaldehyde was observed during solution blow spinning (SBS) process and cinnamaldehyde was mainly located on the surface of resultant nanofibers. Nanofibers all showed antibacterial activity by direct diffusion and vapor release against Escherichia coli O157:H7 , Salmonella typhimurium , and Listeria monocytogenes . Inhibition zones increased as cinnamaldehyde ratio increased. Nanofibers showed larger inhibition effects than films prepared by casting method when S . typhimurium was exposed to the released cinnamaldehyde vapor, although films had higher remaining cinnamaldehyde than nanofibers after preparation. Lower temperature was favorable for cinnamaldehyde retention, and nanofibers added with 10% cinnamaldehyde ratio showed the highest retention over eight-weeks of storage. Results suggest that FSG nanofibers can be prepared by SBS as carriers for antimicrobials.

A Paradigm for Operant Conditioning in Blow Flies ("Phormia Terrae Novae" Robineau-Desvoidy, 1830)

Science.gov (United States)

Sokolowski, Michel B. C.; Disma, Gerald; Abramson, Charles I.

2010-01-01

An operant conditioning situation for the blow fly ("Protophormia terrae novae") is described. Individual flies are trained to enter and reenter a hole as the operant response. Only a few sessions of contingent reinforcement are required to increase response rates. When the response is no longer followed by food, the rate of entering the hole…

Large Eddy simulation of flat plate film cooling at high blowing ratio using open FOAM

Science.gov (United States)

Baagherzadeh Hushmandi, Narmin

2018-06-01

In this work, numerical analysis was performed to predict the behaviour of high Reynolds number turbulent cross-flows used in film cooling applications. The geometry included one row of three discrete coolant holes inclined at 30 degrees to the main flow. In the computational model, the width of the channel was cut into one sixth and symmetry boundaries were applied in the centreline of the coolant hole and along the line of symmetry between two adjacent holes. One of the main factors that affect the performance of film cooling is the blowing ratio of coolant to the main flow. A blowing ratio equal to two was chosen in this study. Analysis showed that the common practice CFD models that employ RANS equations together with turbulence modelling under predict the film cooling effectiveness up to a factor of four. However, LES method showed better agreement of film cooling effectiveness both in tendency and absolute values compared with experimental results.

Dating Pupae of the Blow Fly Calliphora vicina Robineau–Desvoidy 1830 (Diptera: Calliphoridae for Post Mortem Interval—Estimation: Validation of Molecular Age Markers

Directory of Open Access Journals (Sweden)

Barbara K. Zajac

2018-03-01

Full Text Available Determining the age of juvenile blow flies is one of the key tasks of forensic entomology when providing evidence for the minimum post mortem interval. While the age determination of blow fly larvae is well established using morphological parameters, the current study focuses on molecular methods for estimating the age of blow flies during the metamorphosis in the pupal stage, which lasts about half the total juvenile development. It has already been demonstrated in several studies that the intraspecific variance in expression of so far used genes in blow flies is often too high to assign a certain expression level to a distinct age, leading to an inaccurate prediction. To overcome this problem, we previously identified new markers, which show a very sharp age dependent expression course during pupal development of the forensically-important blow fly Calliphora vicina Robineau–Desvoidy 1830 (Diptera: Calliphoridae by analyzing massive parallel sequencing (MPS generated transcriptome data. We initially designed and validated two quantitative polymerase chain reaction (qPCR assays for each of 15 defined pupal ages representing a daily progress during the total pupal development if grown at 17 °C. We also investigated whether the performance of these assays is affected by the ambient temperature, when rearing pupae of C. vicina at three different constant temperatures—namely 17 °C, 20 °C and 25 °C. A temperature dependency of the performance could not be observed, except for one marker. Hence, for each of the defined development landmarks, we can present gene expression profiles of one to two markers defining the mentioned progress in development.

Blowing jets as a circulation flow control to enhancement the lift of wing or generated power of wind turbine

Directory of Open Access Journals (Sweden)

Alexandru DUMITRACHE

2014-06-01

Full Text Available The goal of this paper is to provide a numerical flow analysis based on RANS equations in two directions: the study of augmented high-lift system for a cross-section airfoil of a wing up to transonic regime and the circulation control implemented by tangentially blowing jet over a highly curved surface due to Coanda effect on a rotor blade for a wind turbine. This study were analyzed the performance, sensitivities and limitations of the circulation control method based on blowing jet for a fixed wing as well as for a rotating wing. Directions of future research are identified and discussed.

Transport of nonintrinsic impurities injected by laser blow-off method

International Nuclear Information System (INIS)

Bakos, J.S.

1993-09-01

The transport of nonintrinsic impurities injected by laser blow-off method is theoretically described by solving the two-dimensional (radial and toroidal) time dependent equations of diffusion in the edge plasmas of a tokamak. Explicit expressions and evaluation procedures are given for the calculation of the density profile, temperature profile and the diffusion coefficients for the atoms injected and for the ions formed from the injected atoms from the two-dimensional intensity distribution of line radiation of two sorts of atom and ions formed from the atoms measured by a (matrix) CCD camera time resolved. (orig.)

A note on Burgers' equation with time delay: Instability via finite-time blow-up

International Nuclear Information System (INIS)

Jordan, P.M.

2008-01-01

Burgers' equation with time delay is considered. Using the Cole-Hopf transformation, the exact solution of this nonlinear partial differential equation (PDE) is determined in the context of a (seemingly) well-posed initial-boundary value problem (IBVP) involving homogeneous Dirichlet data. The solution obtained, however, is shown to exhibit a delay-induced instability, suffering blow-up in finite-time

Aerodynamic drag reduction of a simplified squareback vehicle using steady blowing

Energy Technology Data Exchange (ETDEWEB)

Littlewood, R.P. [LaVisionUK Ltd, Grove, Oxon (United Kingdom); Passmore, M.A. [Loughborough University, Department of Aeronautical and Automotive Engineering, Loughborough (United Kingdom)

2012-08-15

A large contribution to the aerodynamic drag of a vehicle arises from the failure to fully recover pressure in the wake region, especially on squareback configurations. A degree of base pressure recovery can be achieved through careful shape optimisation, but the freedom of an automotive aerodynamicist to implement significant shape changes is limited by a variety of additional factors such styling, ergonomics and loading capacity. Active flow control technologies present the potential to create flow field modifications without the need for external shape changes and have received much attention in previous years within the aeronautical industry and, more recently, within the automotive industry. In this work the influence of steady blowing applied at a variety of angles on the roof trailing edge of a simplified 1/4 scale squareback style vehicle has been investigated. Hot-wire anemometry, force balance measurements, surface pressure measurements and PIV have been used to investigate the effects of the steady blowing on the vehicle wake structures and the resulting body forces. The energy consumption of the steady jet is calculated and is used to deduce an aerodynamic drag power change. Results show that overall gains can be achieved; however, the large mass flow rate required restricts the applicability of the technique to road vehicles. Means by which the mass flow rate requirements of the jet may be reduced are discussed and suggestions for further work put forward. (orig.)

Using gas blow methods to realize accurate volume measurement of radioactivity liquid

International Nuclear Information System (INIS)

Zhang Caiyun

2010-01-01

For liquid which has radioactivity, Realized the accurate volume measurement uncertainty less than 0.2% (k=2) by means of gas blow methods presented in the 'American National Standard-Nuclear Material Control-Volume Calibration Methods(ANSI N15.19-1989)' and the 'ISO Committee Drafts (ISO/TC/85/SC 5N 282 )' and Explored a set methods of Data Processing. In the article, the major problems is to solve data acquisition and function foundation and measurement uncertainty estimate. (authors)

A review of bacterial interactions with blow flies (Diptera: Calliphoridae) of medical, veterinary, and forensic importance

Science.gov (United States)

Blow flies are commonly associated with decomposing material. In most cases, the larvae are found feeding on decomposing vertebrate remains. However, some species have specialized to feed on living tissue or can survive on other alternate resources like feces. Because of their affiliation with su...

Blow-Up Criterion of Weak Solutions for the 3D Boussinesq Equations

Directory of Open Access Journals (Sweden)

Zhaohui Dai

2015-01-01

Full Text Available The Boussinesq equations describe the three-dimensional incompressible fluid moving under the gravity and the earth rotation which come from atmospheric or oceanographic turbulence where rotation and stratification play an important role. In this paper, we investigate the Cauchy problem of the three-dimensional incompressible Boussinesq equations. By commutator estimate, some interpolation inequality, and embedding theorem, we establish a blow-up criterion of weak solutions in terms of the pressure p in the homogeneous Besov space Ḃ∞,∞0.

Global existence and blow-up analysis for some degenerate and quasilinear parabolic systems

Directory of Open Access Journals (Sweden)

Haihua Lu

2009-08-01

Full Text Available This paper deals with positive solutions of some degenerate and quasilinear parabolic systems not in divergence form: $u_{1t}=f_1(u_2(\\Delta u_1+a_1u_1,\\cdots, u_{(n-1t}=f_{n-1}(u_n(\\Delta u_{n-1}+a_{n-1} u_{n-1},\\ u_{nt}=f_n(u_1(\\Delta u_n+a_nu_n$ with homogeneous Dirichlet boundary condition and positive initial condition, where $a_i\\ (i=1,2,\\cdots,n$ are positive constants and $f_i\\ (i=1,2,\\cdots,n$ satisfy some conditions. The local existence and uniqueness of classical solution are proved. Moreover, it will be proved that: (i when $\\min\\{a_1,\\cdots,\\ a_n\\}\\leq\\lambda_1$ then there exists global positive classical solution, and all positive classical solutions can not blow up in finite time in the meaning of maximum norm; (ii when $\\min\\{a_1,\\cdots,\\ a_n\\}>\\lambda_1$, and the initial datum $(u_{10},\\cdots,\\ u_{n0}$ satisfies some assumptions, then the positive classical solution is unique and blows up in finite time, where $\\lambda_1$ is the first eigenvalue of $-\\Delta$ in $\\Omega$ with homogeneous Dirichlet boundary condition.

Some problems on non-linear semigroups and the blow-up of integral solutions

International Nuclear Information System (INIS)

Pavel, N.H.

1983-07-01

After some introductory remarks, this highly mathematical document considers a unifying approach in the theory of non-linear semigroups. Then a brief survey is given on blow-up of mild solutions from the semilinear case. Finally, the global behavior of solutions to non-linear evolution equations is addressed; it is found that classical results on the behavior of the maximal solution u as t up-arrow tsub(max) hold also for integral solutions

A binary mixture operated heat pump

International Nuclear Information System (INIS)

Hihara, E.; Saito, T.

1991-01-01

This paper evaluates the performance of possible binary mixtures as working fluids in high- temperature heat pump applications. The binary mixtures, which are potential alternatives of fully halogenated hydrocarbons, include HCFC142b/HCFC22, HFC152a/HCFC22, HFC134a/HCFC22. The performance of the mixtures is estimated by a thermodynamic model and a practical model in which the heat transfer is considered in heat exchangers. One of the advantages of binary mixtures is a higher coefficient of performance, which is caused by the small temperature difference between the heat-sink/-source fluid and the refrigerant. The mixture HCFC142b/HCFC22 is promising from the stand point of thermodynamic performance

Blow-out limits of nonpremixed turbulent jet flames in a cross flow at atmospheric and sub-atmospheric pressures

KAUST Repository

Wang, Qiang; Hu, Longhua; Yoon, Sung Hwan; Lu, Shouxiang; Delichatsios, Michael; Chung, Suk-Ho

2015-01-01

The blow-out limits of nonpremixed turbulent jet flames in cross flows were studied, especially concerning the effect of ambient pressure, by conducting experiments at atmospheric and sub-atmospheric pressures. The combined effects of air flow

Self Induced Buoyant Blow Off in Upward Flame Spread on Thin Solid Fuels

Science.gov (United States)

Johnston, Michael C.; T'ien, James S.; Muff, Derek E.; Olson, Sandra L.; Ferkul, Paul V.

2013-01-01

Upward flame spread experiments were conducted on a thin fabric cloth consisting of 75% cotton and 25% fiberglass. The sample is sandwiched symmetrically with stainless steel plates with the exposed width varying between 2 to 8.8 cm from test to test and >1.5m tall. The bottom edge was ignited resulting in a symmetric two sided flame. For the narrower samples (. 5cm), two sided flame growth would proceed until reaching some limiting value (15-30 cm depending on sample width). Fluctuation or instability of the flame base on one side would initially become visible and then the flame base would retreat downstream and cause extinguishment on one side. Detailed examination of the still images shows that the fuel continues to vaporize from the extinguished side due to the thermally thin nature of the fuel. But, due to the remaining inert fiberglass mesh, which acts as a flashback arrestor, the extinguished side was not able to be reignited by the remaining flame. The remaining flame would then shrink in length due to the reduced heat transfer to the solid to a shorter length. The one-sided flame will spread stably with a constant speed and a constant flame length to the end of the sample. A constant length flame implies that the pyrolysis front and the burnt out fronts move at the same speed. For the wider samples (. 7cm), no one-sided extinction is observed. Two-sided flames spread all the way to the top of the sample. For these wider widths, the flames are still growing and have not reached their limiting length if it exists. Care was taken to minimize the amount of non-symmetries in the experimental configuration. Repeated tests show that blow-off can occur on either side of the sample. The flame growth is observed to be very symmetric during the growth phase and grew to significant length (>10cm) before extinction of the flame on one side. Our proposed explanation of this unusual phenomenon (i.e. stronger two ]sided flame cannot exist but weaker one-sided flame can

Cryoinsulation Material Development to Mitigate Obsolescence Risk for Global Warming Potential Foams

Science.gov (United States)

Protz, Alison; Bruyns, Roland; Nettles, Mindy

2015-01-01

Cryoinsulation foams currently being qualified for the Space Launch System (SLS) core stage are nonozone- depleting substances (ODP) and are compliant with current environmental regulations. However, these materials contain the blowing agent HFC-245fa, a hydrofluorocarbon (HFC), which is a Global Warming Potential (GWP) substance. In August 2014, the Environmental Protection Agency (EPA) proposed a policy change to reduce or eliminate certain HFCs, including HFC-245fa, in end-use categories including foam blowing agents beginning in 2017. The policy proposes a limited exception to allow continued use of HFC and HFC-blend foam blowing agents for military or space- and aeronautics-related applications, including rigid polyurethane spray foams, but only until 2022.

Development and validation of a new technique for estimating a minimum postmortem interval using adult blow fly (Diptera: Calliphoridae) carcass attendance.

Science.gov (United States)

Mohr, Rachel M; Tomberlin, Jeffery K

2015-07-01

Understanding the onset and duration of adult blow fly activity is critical to accurately estimating the period of insect activity or minimum postmortem interval (minPMI). Few, if any, reliable techniques have been developed and consequently validated for using adult fly activity to determine a minPMI. In this study, adult blow flies (Diptera: Calliphoridae) of Cochliomyia macellaria and Chrysomya rufifacies were collected from swine carcasses in rural central Texas, USA, during summer 2008 and Phormia regina and Calliphora vicina in the winter during 2009 and 2010. Carcass attendance patterns of blow flies were related to species, sex, and oocyte development. Summer-active flies were found to arrive 4-12 h after initial carcass exposure, with both C. macellaria and C. rufifacies arriving within 2 h of one another. Winter-active flies arrived within 48 h of one another. There was significant difference in degree of oocyte development on each of the first 3 days postmortem. These frequency differences allowed a minPMI to be calculated using a binomial analysis. When validated with seven tests using domestic and feral swine and human remains, the technique correctly estimated time of placement in six trials.

Towards improving the efficiency of blowing through a permeable wall and prospects of its use for a flow control

Science.gov (United States)

Kornilov, V. I.; Boiko, A. V.

2016-10-01

Modern achievements, status, and prospects of studies on reducing the turbulent friction and aerodynamic drag with the help of the blowing through a permeable wall are discussed. The main focus is placed upon a physical modeling of the process of boundary layer blowing in the framework of the dimensional theory, a critical analysis of experimental and numerical results for different conditions of air blowing through a high-tech finely perforated wall including the case of external-pressure-flow air supply in wind tunnel, and elicitation of the physical mechanisms responsible for the reduction of turbulent friction at flow-exposed surfaces. It is shown that the use of air supply through the micro-perforated wall with low effective roughness, which is manufactured in compliance with the highest necessary requirements to quality and geometry of orifices, is quite a justified means for easy, affordable, and reliable control of near-wall turbulent flows in laboratory experiment and numerical simulation. This approach can provide a sustained reduction of local skin friction coefficient along flat plate, which in some cases reaches 90%. At the request of all authors of the paper and with the agreement of the Proceedings Editor, an updated version of this article was published on 26 October 2016. The original version supplied to AIP Publishing contained a misrepresentation in Figure 1. This has been corrected in the updated and republished article.

LS1 Report: Blowing away the cobwebs

CERN Multimedia

Anaïs Schaeffer

2014-01-01

With the pressure tests now complete (see here), we are coming to the equally important phase of cleaning the machine. With all the work performed over the past year, quite a lot of dust and dirt has accumulated in certain areas of the accelerator.   Result of the flushing performed in 2007 in Sector 5-6... This year, in Sector 6-7, the filters were particularly clean. A simple and efficient solution, known as helium flushing, has been devised by the Cryogenics group (TE-CRG) to clean up these areas. “We circulate helium gas around the machine in both the cryogenic distribution lines and the magnets,” explains Gérard Ferlin, who is responsible for the flushing operations. “This blows all the debris into a filter at the outlet. ” The flow-rate needs to be high enough to ensure that everything is swept away, so the helium is injected at rates of between 15 and 40 metres per second, much higher than in normal operation. “There&rs...

Asymptotic stability and blow up for a semilinear damped wave equation with dynamic boundary conditions

KAUST Repository

Gerbi, Stéphane

2011-12-01

In this paper we consider a multi-dimensional wave equation with dynamic boundary conditions, related to the KelvinVoigt damping. Global existence and asymptotic stability of solutions starting in a stable set are proved. Blow up for solutions of the problem with linear dynamic boundary conditions with initial data in the unstable set is also obtained. © 2011 Elsevier Ltd. All rights reserved.

Asymptotic stability and blow up for a semilinear damped wave equation with dynamic boundary conditions

KAUST Repository

Gerbi, Sté phane; Said-Houari, Belkacem

2011-01-01

In this paper we consider a multi-dimensional wave equation with dynamic boundary conditions, related to the KelvinVoigt damping. Global existence and asymptotic stability of solutions starting in a stable set are proved. Blow up for solutions of the problem with linear dynamic boundary conditions with initial data in the unstable set is also obtained. © 2011 Elsevier Ltd. All rights reserved.

A Numerical Study of Anti-Vortex Film Cooling Designs at High Blowing Ratio

Science.gov (United States)

Heidmann, James D.

2008-01-01

A concept for mitigating the adverse effects of jet vorticity and liftoff at high blowing ratios for turbine film cooling flows has been developed and studied at NASA Glenn Research Center. This "anti-vortex" film cooling concept proposes the addition of two branched holes from each primary hole in order to produce a vorticity counter to the detrimental kidney vortices from the main jet. These vortices typically entrain hot freestream gas and are associated with jet separation from the turbine blade surface. The anti-vortex design is unique in that it requires only easily machinable round holes, unlike shaped film cooling holes and other advanced concepts. The anti-vortex film cooling hole concept has been modeled computationally for a single row of 30deg angled holes on a flat surface using the 3D Navier-Stokes solver Glenn-HT. A modification of the anti-vortex concept whereby the branched holes exit adjacent to the main hole has been studied computationally for blowing ratios of 1.0 and 2.0 and at density ratios of 1.0 and 2.0. This modified concept was selected because it has shown the most promise in recent experimental studies. The computational results show that the modified design improves the film cooling effectiveness relative to the round hole baseline and previous anti-vortex cases, in confirmation of the experimental studies.

A novel integrated approach for path following and directional stability control of road vehicles after a tire blow-out

Science.gov (United States)

Wang, Fei; Chen, Hong; Guo, Konghui; Cao, Dongpu

2017-09-01

The path following and directional stability are two crucial problems when a road vehicle experiences a tire blow-out or sudden tire failure. Considering the requirement of rapid road vehicle motion control during a tire blow-out, this article proposes a novel linearized decoupling control procedure with three design steps for a class of second order multi-input-multi-output non-affine system. The evaluating indicators for controller performance are presented and a performance related control parameter distribution map is obtained based on the stochastic algorithm which is an innovation for non-blind parameter adjustment in engineering implementation. The analysis on the robustness of the proposed integrated controller is also performed. The simulation studies for a range of driving conditions are conducted, to demonstrate the effectiveness of the proposed controller.

Metabolism of the hydrochlorofluorocarbon 1,2-dichloro-1,1-difluoroethane.

Science.gov (United States)

Harris, J W; Anders, M W

1991-01-01

1,2-Dichloro-1,1-difluoroethane (HCFC-132b) is a potential substitute for some ozone-depleting chlorofluorocarbons and a model for other 1,1,1,2-tetrahaloethanes under consideration as chlorofluorocarbon substitutes. Male Fischer 344 rats were given 10 mmol/kg HCFC-132b dissolved in corn oil by intraperitoneal injection. An NMR assay for covalent binding of HCFC-132b metabolites to liver proteins was negative, whereas binding was observed in halothane-treated rats. Total urinary metabolites excreted by rats given HCFC-132b during the first 24 h amounted to 1.8 +/- 0.1% of the injected dose, as determined by 19F NMR. During the first 6 h, metabolites of HCFC-132b corresponding to 2-chloro-2,2-difluoroethyl glucuronide, unknown metabolite A, chlorodifluoroacetic acid, and chlorodifluoroacetaldehyde hydrate [both free and conjugated (unknown metabolite B)] were excreted in urine in the approximate ratio 100:9:3:7, respectively. Metabolite A is apparently an O-conjugate of 2-chloro-2,2-difluoroethanol; unconjugated 2-chloro-2,2-difluoroethanol was not detected in urine. The 19F NMR spectrum of metabolite B indicates the formation of a hemiacetal of chlorodifluoroacetaldehyde. Repeated exposure of rats to HCFC-132b significantly increased both the rate of chlorodifluoroacetic acid excretion and the relative fraction of the HCFC-132b dose excreted as chlorodifluoroacetic acid in urine. Incubation of HCFC-132b with rat hepatic microsomes yielded chlorodifluoroacetaldehyde hydrate as the only fluorinated product. The in vitro metabolism of HCFC-132b was increased in microsomes from pyridine-treated rats as compared with control rats, and HCFC-132b metabolism was inhibited by p-nitrophenol, indicating that the cytochrome P-450 isoform IIE1 is largely responsible for the initial hydroxylation of HCFC-132b.

Emission estimates of HCFCs and HFCs in California from the 2010 CalNex study

Science.gov (United States)

Barletta, Barbara; Carreras-Sospedra, Marc; Cohan, Alex; Nissenson, Paul; Dabdub, Donald; Meinardi, Simone; Atlas, Elliot; Lueb, Rich; Holloway, John S.; Ryerson, Thomas B.; Pederson, James; VanCuren, Richard A.; Blake, Donald R.

2013-02-01

The CalNex 2010 (California Research at the Nexus of Air Quality and Climate Change) study was designed to evaluate the chemical composition of air masses over key source regions in California. During May to June 2010, air samples were collected on board a National Oceanic and Atmospheric Administration (NOAA) WP-3D aircraft over the South Coast Air Basin of California (SoCAB) and the Central Valley (CV). This paper analyzes six effective greenhouse gases—chlorodifluoromethane (HCFC-22), 1,1-dichloro-1-fluoroethane (HCFC-141b), 1-chloro-1,1-difluoroethane (HCFC-142b), 2-chloro-1,1,1,2-tetrafluoroethane (HCFC-124), 1,1,1,2-tetrafluoroethane (HFC-134a), and 1,1-difluoroethane (HFC-152a)—providing the most comprehensive characterization of chlorofluorocarbon (CFC) replacement compound emissions in California. Concentrations of measured HCFCs and HFCs are enhanced greatly throughout the SoCAB and CV, with highest levels observed in the SoCAB: 310 ± 92 pptv for HCFC-22, 30.7 ± 18.6 pptv for HCFC-141b, 22.9 ± 2.0 pptv for HCFC-142b, 4.86 ± 2.56 pptv for HCFC-124, 109 ± 46.4 pptv for HFC-134a, and 91.2 ± 63.9 pptv for HFC-152a. Annual emission rates are estimated for all six compounds in the SoCAB using the measured halocarbon to carbon monoxide (CO) mixing ratios and CO emissions inventories. Emission rates of 3.05 ± 0.70 Gg for HCFC-22, 0.27 ± 0.07 Gg for HCFC-141b, 0.06 ± 0.01 Gg for HCFC-142b, 0.11 ± 0.03 Gg for HCFC-124, 1.89 ± 0.43 Gg for HFC-134a, and 1.94 ± 0.45 Gg for HFC-152b for the year 2010 are calculated for the SoCAB. These emissions are extrapolated from the SoCAB region to the state of California using population data. Results from this study provide a baseline emission rate that will help future studies determine if HCFC and HFC mitigation strategies are successful.

Soot blowing methods and soot steam consumption in Swedish recovery boilers; Sotningsmetoder och sotaangfoerbrukning i svenska sodapannor

Energy Technology Data Exchange (ETDEWEB)

Svedin, Kristoffer; Wallin, Erik; Ahlroth, Mikael

2008-09-15

The aim with the report was to put together a description of the current state of the sootblowing systems at Swedish recovery boilers, and to explain differences in cleanability and sootblowing efficiency. In chapter 4 a summary of new techniques and alternative soot blowing methods is found. The report is intended for persons working in the pulp industry. To facilitate the benchmarking the recovery boilers have been divided into two groups. Group A comprises recovery boilers which only have one stop per year and the remaining recovery boilers with more than one stop are classified into group B. The following conclusions, based on the recovery boiler design specifications, are of importance to achieve high boiler availability: Low furnace load; High recovery boiler, wide furnace bottom area; Modern air ports; Small or no correlation between cross pitch division in heat surfaces and cleanability could be seen. The expectation was to identify such a relation. However there are doubts on the correctness in reported data. The amount of chlorine and potassium is assumed to affect the cleanability for a few recovery boilers, but for the majority the amounts are low and most likely do not impact the operation. Because of the large impact of the recovery boilers design data (furnace area, load etc.) on the sootblowing, it has been hard to identify the relation cleanability contra sootblowing system. The relations that could be seen are: No distinction between normally designed nozzles and 'high efficiency' nozzles could be identified. The operational conditions for the different models differ a lot and the effect of nozzle type could not be distinguished. Only a minority of the soot blowing sequences are known from the study. In the recovery boilers with problematic areas improvements can be made in the soot blowing sequence. Four recovery boilers are using intelligent soot blowing of some kind. Two of these boilers have low availability and the other two have

Longitudinal phase space characterization of the blow-out regime of rf photoinjector operation

OpenAIRE

J. T. Moody; P. Musumeci; M. S. Gutierrez; J. B. Rosenzweig; C. M. Scoby

2009-01-01

Using an experimental scheme based on a vertically deflecting rf deflector and a horizontally dispersing dipole, we characterize the longitudinal phase space of the beam in the blow-out regime at the UCLA Pegasus rf photoinjector. Because of the achievement of unprecedented resolution both in time (50 fs) and energy (1.0 keV), we are able to demonstrate some important properties of the beams created in this regime such as extremely low longitudinal emittance, large temporal energy chirp, and ...

The effect of warm air-blowing on the microtensile bond strength of one-step self-etch adhesives to root canal dentin.

Science.gov (United States)

Taguchi, Keita; Hosaka, Keiichi; Ikeda, Masaomi; Kishikawa, Ryuzo; Foxton, Richard; Nakajima, Masatoshi; Tagami, Junji

2018-02-01

The use of warm air-blowing to evaporate solvents of one-step self-etch adhesive systems (1-SEAs) has been reported to be a useful method. The purpose of this study was to evaluate the effect of warm air-blowing on root canal dentin. Four 1-SEAs (Clearfil Bond SE ONE, Unifil Core EM self-etch bond, Estelink, BeautiDualbond EX) were used. Each 1-SEA was applied to root canal dentin according to the manufacturers' instructions. After the adhesives were applied, solvent was evaporated using either normal air (23±1°C) or warm air (80±1°C) for 20s, and resin composite was placed in the post spaces. The air from the dryer, which could be used in normal- or hot-air-mode, was applied at a distance of 5cm above the root canal cavity in the direction of tooth axis. The temperature of the stream of air from the dryer in the hot-air-mode was 80±1°C, and in the normal mode, 23±1°C. After water storage of the specimens for 24h, the μTBS were evaluated at the coronal and apical regions. The μTBSs were statistically analyzed using three-way ANOVA and Student's t-test with Bonferroni correction (α=0.05). The warm air-blowing significantly increased the μTBS of all 1-SEAs at the apical regions, and also significantly increased the μTBS of two adhesives (Estelink and BeautiDualBond EX) at coronal regions. The μTBS of 1-SEAs to root canal dentin was improved by using warm air-blowing. Copyright © 2017 Japan Prosthodontic Society. Published by Elsevier Ltd. All rights reserved.

Generating Soap Bubbles by Blowing on Soap Films

Science.gov (United States)

Salkin, Louis; Schmit, Alexandre; Panizza, Pascal; Courbin, Laurent

2016-02-01

Making soap bubbles by blowing air on a soap film is an enjoyable activity, yet a poorly understood phenomenon. Working either with circular bubble wands or long-lived vertical soap films having an adjustable steady state thickness, we investigate the formation of such bubbles when a gas is blown through a nozzle onto a film. We vary film size, nozzle radius, space between the film and nozzle, and gas density, and we measure the gas velocity threshold above which bubbles are formed. The response is sensitive to containment, i.e., the ratio between film and jet sizes, and dissipation in the turbulent gas jet, which is a function of the distance from the film to the nozzle. We rationalize the observed four different regimes by comparing the dynamic pressure exerted by the jet on the film and the Laplace pressure needed to create the curved surface of a bubble. This simple model allows us to account for the interplay between hydrodynamic, physicochemical, and geometrical factors.

Acute effect of blows to the head due one bout of amateur boxing match on electroencephalography (EEG

Directory of Open Access Journals (Sweden)

keyvan Shabanimoghadam

2011-06-01

Conclusion: It is seems that in boxing sport the nature of blow to the head can lead to brain tissue electrical flow disturbance. This tension that is accompanied with acute mild brain injury and is observed in boxers, electroencephalography, is serious and can lead to next complications and injuries.

40 CFR 372.65 - Chemicals and chemical categories to which this part applies.

Science.gov (United States)

2010-07-01

.../1/87 1-Chloro-1,1-difluoroethane (HCFC-142b) 75-68-3 1/1/94 Chlorodifluoromethane (HCFC-22) 75-45-6...-1,4-Dichloro-2-butene 110-57-6 1/1/95 1,2-Dichloro-1,1-difluoroethane (HCFC-132b) 1649-08-7 1/1/95... tert-Butyl alcohol 1/1/87 75-68-3 1-Chloro-1,1-difluoroethane (HCFC-142b) 1/1/94 75-69-4...

The existence of global solution and ''blow up'' phenomenon for the system of multi-dimensional symmetric regularized wave equations

International Nuclear Information System (INIS)

Guo Boling.

1988-08-01

The existence and uniqueness of the global smooth solution for the initial-boundary value problem of the system of multi-dimensions SRWE are proved. The sufficient conditions of ''blowing up'' of the solution are given. (author). 6 refs

Investigation on thermomechanical properties of poly (l-lactic acid) for the stretch blow moulding process of bioresorbable vascular scaffold

Science.gov (United States)

Wei, Huidong; Menary, Gary

2017-10-01

Stretch blow moulding process has been used for the manufacture of bioresorbable vascular scaffold (BVS) made by poly (l-lactic acid) (PLLA) to improve its mechanical performance. In order to better understand the process, thermomechanical properties of PLLA were investigated by experimental method. Extruded PLLA sheets were biaxial stretched under strain rate of 1s-1, 4s-1 and 16s-1 to simulate the deformation process applicable in the blow moulding process. Both the equal-biaxial stretch and constant-width stretch were conducted by an in-house developed equipment. By differential scanning calorimeter (DSC), thermal analysis for materials before and after stretch were compared to evaluate the microstructural change of PLLA materials in the deformation process. A constitutive model based on glass rubber model was presented to simulate the mechanical behaviour of PLLA above glass transition under biaxial deformation.

"Blow-torch phenomenon" during laser assisted excision of a thyroglossal cyst at the base of the tongue

Directory of Open Access Journals (Sweden)

Anitha G Bhat

2012-01-01

Full Text Available We report a case of blow-torch phenomenon encountered during diode laser assisted excision of a thyroglossal cyst in a child. This is first such case report from India and highlights an unusual complication which anesthesiologists need to be aware of due to the increasing use of operative laser.

(H)-FCKW foamed insulating materials in the building industry in Germany. Estimation of the potential emissions up to the year 2010; (H)-FCKW-geschaeumte Daemmstoffe im Bauwesen in Deutschland. Schaetzung der potentiellen Emissionen bis zum Jahr 2010

Energy Technology Data Exchange (ETDEWEB)

Obernosterer, Richard [Ressourcen Management Agentur GmbH, Villach (Austria)

2012-09-15

CFCs and HCFCs are controlled substances under European Regulation (EC) No. 1005/2009. Article 22 of that Regulation provides that controlled substances contained in certain products (e.g. insulating materials) must be recovered, if technically and economically feasible, or be destroyed without prior recovery. Annex VII lists specific technologies for destruction, recycling or reclamation. In Germany, the use of (H)CFCs in insulating materials has been prohibited since 1995 (R 11 and R 12) and 2000 (R 22). At European level, use of HCFCs (141b and 142b) has been banned since 2002 mainly in the production of extruded polystyrene rigid foam and since 2003 in the production of polyurethane foams. Few data have become available to date on the amounts of (H)CFCs produced and banked up to the time the prohibitions went into effect. The present report therefore provides details on the amounts of (H)CFC-containing insulating materials installed in Germany and estimates the quantities of (H)CFCs still present in them. The study focuses on rigid XPS foam and rigid PU foam used in the construction sector, due to the original objective of the study and the quantitative significance of these foams. XPS insulating foams: XPS panels were assumed to have an average density of 33 kg/m3. Based on annual foam use (volume), density, the market shares of the blowing agents, and blowing agent content in the foam, the annual increase in banked amounts of blowing agents was estimated. Annual fugitive losses were deducted from those banks, specific to the relevant products and blowing agents. As result a bank of approximately 43.7 kt or 15 000 t-ODP was estimated for Germany in 2009. PU insulating foams: Based on annual foam use (volume), density (assumed to be 41 kg/m3 for PU sandwich panels and 33 kg/m3 for other PU products), the market shares of the blowing agents, and blowing agent content in the foam, the annual increase in banked amounts of blowing agents was estimated. Annual

Improved Longitudinal Blow-up and Shaving in the Booster

CERN Document Server

Hancock, S

2013-01-01

The low-intensity proton beam for p-Pb collisions in the LHC did not come back in the Booster at the beginning of 2013 anything like it had been set up at the end of 2012. In particular there were unexplained intensity fluctuations of ±100%. Although the root cause of the drift in performance was never established, its investigation revealed long-standing issues in the longitudinal plane which, when corrected, allowed single-bunch beams to be delivered with unprecedented reproducibility and control of both intensity and longitudinal emittance. The new approach was adopted for the ion run and subsequently for MDs at higher intensities, where it made possible a robust control of intensity at constant 6D phase space volume. Post-LS1, it may even provide a platform upon which to build a more exotic controlled longitudinal blow-up to generate higher intensity bunches with a flattened line density.

Blowing up solutions for a biharmonic equation with critical nonlinearity

International Nuclear Information System (INIS)

El Mehdi, K.; Hammami, M.

2004-05-01

In this paper we consider the following biharmonic equation with critical exponent (P ε ):Δ 2 u=Ku (n+4)/(n-4)-ε , u>0 in Ω and u=Δu=0 on ∂Ω, where Ω is a smooth bounded domain in R n , n≥5, ε is a small positive parameter, and K is a smooth positive function in Ω-bar. We construct solutions of (P ε ) which blow up and concentrate at strict local maximum of K either at the boundary or in the interior of Ω. We also construct solutions of (P ε ) concentrating at an interior strict local minimum point of K. Finally, we prove a nonexistence result for the supercritical problem which is in sharp contrast to what happened for (P ε ). (author)

Metabolism and toxicity of hydrochlorofluorocarbons: current knowledge and needs for the future.

Science.gov (United States)

Anders, M W

1991-12-01

Hydrochlorofluorocarbons (HCFCs) are being developed as replacements for chlorofluorocarbons (CFCs) that deplete stratospheric ozone. The depletion of stratospheric ozone may increase the intensity of ultraviolet radiation at the earth's surface, which may be associated with global, adverse human health effects. The greater tropospheric lability of HCFCs, which is due to the presence of C-H bonds, reduces HCFC migration to the stratosphere; HCFCs should, therefore, cause less depletion of stratospheric ozone than CFCs. HCFCs under development include HCFC-22 (chlorodifluoromethane), HCFC-123 (2,2-dichloro-1,1,1-trifluoroethane), HCFC-132b (1,2-dichloro-1,1-difluoroethane), HCFC-134a (1,1,1,2-tetrafluoroethane), HCFC-141b (1,1-dichloro-1-fluoroethane, and HCFC-142b (1-chloro-1,1-difluoroethane). With the exception of HCFC-22, which is already in use, the metabolism and toxicity of HCFCs have not been studied in detail. By analogy to chlorinated ethanes, predictions can be made about the possible metabolism of HCFCs, but there are insufficient data available to predict rates of metabolism. Although most HCFCs appear to show low acute toxicity, some HCFCs are mutagenic in the Ames test. Hence, future research on HCFCs should include studies on the in vivo and in vitro metabolism of HCFCs as well as on their toxicity in in vivo and in vitro systems.

40 CFR 82.19 - Apportionment of baseline consumption allowances for class II controlled substances.

Science.gov (United States)

2010-07-01

... allowances for class II controlled substances. 82.19 Section 82.19 Protection of Environment ENVIRONMENTAL... Consumption Controls § 82.19 Apportionment of baseline consumption allowances for class II controlled... Ineos Fluor Americas HCFC-22 2,546,305 Kivlan & Company HCFC-22 2,081,018 MDA Manufacturing HCFC-22 2...

Simulative design and process optimization of the two-stage stretch-blow molding process

Energy Technology Data Exchange (ETDEWEB)

Hopmann, Ch.; Rasche, S.; Windeck, C. [Institute of Plastics Processing at RWTH Aachen University (IKV) Pontstraße 49, 52062 Aachen (Germany)

2015-05-22

The total production costs of PET bottles are significantly affected by the costs of raw material. Approximately 70 % of the total costs are spent for the raw material. Therefore, stretch-blow molding industry intends to reduce the total production costs by an optimized material efficiency. However, there is often a trade-off between an optimized material efficiency and required product properties. Due to a multitude of complex boundary conditions, the design process of new stretch-blow molded products is still a challenging task and is often based on empirical knowledge. Application of current CAE-tools supports the design process by reducing development time and costs. This paper describes an approach to determine optimized preform geometry and corresponding process parameters iteratively. The wall thickness distribution and the local stretch ratios of the blown bottle are calculated in a three-dimensional process simulation. Thereby, the wall thickness distribution is correlated with an objective function and preform geometry as well as process parameters are varied by an optimization algorithm. Taking into account the correlation between material usage, process history and resulting product properties, integrative coupled simulation steps, e.g. structural analyses or barrier simulations, are performed. The approach is applied on a 0.5 liter PET bottle of Krones AG, Neutraubling, Germany. The investigations point out that the design process can be supported by applying this simulative optimization approach. In an optimization study the total bottle weight is reduced from 18.5 g to 15.5 g. The validation of the computed results is in progress.

Simulative design and process optimization of the two-stage stretch-blow molding process

International Nuclear Information System (INIS)

Hopmann, Ch.; Rasche, S.; Windeck, C.

2015-01-01

The total production costs of PET bottles are significantly affected by the costs of raw material. Approximately 70 % of the total costs are spent for the raw material. Therefore, stretch-blow molding industry intends to reduce the total production costs by an optimized material efficiency. However, there is often a trade-off between an optimized material efficiency and required product properties. Due to a multitude of complex boundary conditions, the design process of new stretch-blow molded products is still a challenging task and is often based on empirical knowledge. Application of current CAE-tools supports the design process by reducing development time and costs. This paper describes an approach to determine optimized preform geometry and corresponding process parameters iteratively. The wall thickness distribution and the local stretch ratios of the blown bottle are calculated in a three-dimensional process simulation. Thereby, the wall thickness distribution is correlated with an objective function and preform geometry as well as process parameters are varied by an optimization algorithm. Taking into account the correlation between material usage, process history and resulting product properties, integrative coupled simulation steps, e.g. structural analyses or barrier simulations, are performed. The approach is applied on a 0.5 liter PET bottle of Krones AG, Neutraubling, Germany. The investigations point out that the design process can be supported by applying this simulative optimization approach. In an optimization study the total bottle weight is reduced from 18.5 g to 15.5 g. The validation of the computed results is in progress

An Innovative Oil Pollution Containment Method for Ship Wrecks Proposed for Offshore Well Blow-outs

OpenAIRE

ANDRITSOS Fivos; COJINS Hans

2011-01-01

In the aftermath of the PRESTIGE disaster, an innovative system for the prompt intervention on oil pollution sources (primarily ship wrecks) at great depths was conceived at the Joint Research Center of the European Commission. This system, with some re-engineering, could also serve for collecting oil and gas leaking after an offshore well blow-out and could constitute a reference method for prompt intervention on deep water oil pollution sources like ship wrecks and blown-out offshore wells....

Treatment of reactive process wastewater with high-level ammonia by blow-off method

International Nuclear Information System (INIS)

Chen Xiaotong; Quan Ying; Wang Yang; Fu Genna; Liu Bing; Tang Yaping

2012-01-01

The ceramic UO 2 kernels for nuclear fuel elements of high temperature gas cooled reactors were prepared through sol-gel process with uranyl nitrate, which produces process wastewater containing high-level ammonia and uranium. The blow-off method on a bench scale was investigated to remove ammonia from reactive wastewater. Under the optimized operating conditions, the ammonia can be removed by more than 95%, with little reactive uranium distilled. The effects of pH, heating temperature and stripping time were studied. Static tests with ion-exchange resin indicate that ammonia removal treatment increases uranium accumulation in anion exchange resin. (authors)

Enhancement of efficacy of process water monitors in detecting heavy water leak in steam generator blow down lines

International Nuclear Information System (INIS)

Mitra, S.R.; Kohale, S.D.; Parida, B.K.; Gathe, G.D.; Pati, C.K.; Mudgal, B.K.; Niraj; Pawar, S.K.

2006-01-01

The Steam Generator (SG) serves as an interface between primary and secondary cycle in Pressurized Heavy Water Reactor (PHWR). Failure of steam generator tubes result in leaking of active heavy water in the secondary closed loop. In Tarapur Atomic Power Station-3 and 4 (TAPS- 3 and 4), Scintillator detectors are provided to detect on line heavy water leakages in SG and moderator heat exchangers by monitoring Nitrogen-16 ( 16 N) and Oxygen-19 ( 19 O) activities. Efficacy of detection of these activities at designed detector position on SG blow down line in presence of background radiation field is analysed theoretically. The count rate of 19 O and 16 N estimated at the detector position inside Reactor Building (RB) shows that detectors only respond to very high leak rates due to presence of high ambient radiation level even though sensitivity is appreciably good. For detector position in RB in the accessible areas and out side the RE containment, the travel time for the blow down feed water becomes moderately and very long respectively resulting in poor sensitivity. However the results show that wherever background levels is low, the efficacy of leak detection becomes considerably better than the results obtained when detector is placed inside RB. The study was validated during the reactor operation by recording the detector count rates due to prevalent ambient radiation level near to the detectors. Subsequently the detectors were relocated in an area inside RB where relocation was feasible, travel time of the blow down feed water was moderate and the area had an relatively low ambient radiation level. This paper discusses the methodology adopted during the study and results obtained during theoretical estimation and practical validation. (author)

Methane oxidation and degradation of organic compounds in landfill soil covers

DEFF Research Database (Denmark)

Scheutz, Charlotte; Kjeldsen, Peter

2002-01-01

High rates of methane oxidation and degradation of the lowed halogenated methanes (TCM and DCM) and HCFCs (HCFC-21 and HCFC-22) were found in an investigation of the oxidation of methane and halogenated organic compunds (HOCs) in landfill gas affected soil. The degradation followed zero-order kin......High rates of methane oxidation and degradation of the lowed halogenated methanes (TCM and DCM) and HCFCs (HCFC-21 and HCFC-22) were found in an investigation of the oxidation of methane and halogenated organic compunds (HOCs) in landfill gas affected soil. The degradation followed zero...

Quantifying pteridines in the heads of blow flies (Diptera: Calliphoridae): Application for forensic entomology.

Science.gov (United States)

Cammack, J A; Reiskind, M H; Guisewite, L M; Denning, S S; Watson, D W

2017-11-01

In forensic cases involving entomological evidence, establishing the postcolonization interval (post-CI) is a critical component of the investigation. Traditional methods of estimating the post-CI rely on estimating the age of immature blow flies (Diptera: Calliphoridae) collected from remains. However, in cases of delayed discovery (e.g., when remains are located indoors), these insects may have completed their development and be present in the environment as adults. Adult fly collections are often ignored in cases of advanced decomposition because of a presumed little relevance to the investigation; herein we present information on how these insects can be of value. In this study we applied an age-grading technique to estimate the age of adults of Chrysomya megacephala (Fabricius), Cochliomyia macellaria (Fabricius), and Phormia regina (Meigen), based on the temperature-dependent accumulation of pteridines in the compound eyes, when reared at temperatures ranging from 5 to 35°C. Age could be estimated for all species*sex*rearing temperature combinations (mean r 2 ±SE: 0.90±0.01) for all but P. regina reared at 5.4°C. These models can be used to increase the precision of post-CI estimates for remains found indoors, and the high r 2 values of 22 of the 24 regression equations indicates that this is a valid method for estimating the age of adult blow flies at temperatures ≥15°C. Copyright © 2017 Elsevier B.V. All rights reserved.

On Blowing Up the Pokies: The Pokie Lounge as a Cultural Site of Neoliberal Governmentality in Australia

Directory of Open Access Journals (Sweden)

Fiona Nicoll

2011-03-01

Full Text Available In 1999 The Whitlams, a popular ‘indie’ band named after a former Australian prime minister whose government was controversially sacked in 1975 by the Governor-General, released a single titled ‘Blow up the Pokies’. Written about a former band member’s fatal attraction to electronic gaming machines (henceforth referred to as ‘pokies’, the song was mixed by a top LA producer, a decision that its writer and The Whitlam’s front-man, Tim Freedman, describes as calculated to ‘get it on big, bombastic commercial radio’. The investment paid off and the song not only became a big hit for the band, it developed a legacy beyond the popular music scene, with Freedman invited to write the foreword of a ‘self-help manual for giving up gambling’ as well as appearing on public affairs television shows to discuss the issue of problem gambling. The lyrics of ‘Blow up the Pokies’ frame the central themes of this article: spaces, technologies and governmentality of gambling. It then explores what cultural articulations of resistance to the pokie lounge tell us about broader social and cultural dynamics of neoliberal governmentality in Australia.

A paradigm for operant conditioning in blow flies (Phormia terrae novae Robineau-Desvoidy, 1830).

Science.gov (United States)

Sokolowski, Michel B C; Disma, Gérald; Abramson, Charles I

2010-01-01

An operant conditioning situation for the blow fly (Protophormia terrae novae) is described. Individual flies are trained to enter and reenter a hole as the operant response. Only a few sessions of contingent reinforcement are required to increase response rates. When the response is no longer followed by food, the rate of entering the hole decreases. Control procedures revealed that rate of responding is not a simple overall result of feeding or of aging. The flies entered into the hole only if the response was required to obtain the food.

Chemotaxonomic Profile and Intraspecific Variation in the Blow Fly of Forensic Interest Chrysomya megacephala (Diptera: Calliphoridae).

Science.gov (United States)

Paula, Michele C; Antonialli-Junior, William F; Mendonça, Angélica; Michelutti, Kamylla B; Eulalio, Aylson D M M; Cardoso, Claudia A L; de Lima, Thiago; Von Zuben, Cláudio J

2017-01-01

Necrophagous insects such as blow flies (Diptera: Calliphoridae) are considered crucial in forensic entomology. Identification at species level and determination of larval stage are the basis for estimation of postmortem interval (PMI). Insect evidence can also be used in the determination of crime scenes, since body displacement is common. The aim of this study was to determine the chemotaxonomic profile and intraspecific variability of the forensically important blow fly Chrysomya megacephala (F. 1794). Adults were collected in the municipalities of Dourados-MS (Brazil) and Rio Claro-SP (Brazil), and then transferred to the laboratory for oviposition and development of the immature stages. Chemical analysis of cuticular compounds was performed by gas chromatography. Cuticular chemical profiles varied significantly between the two populations, as well as between developmental stages, supporting the use of these compounds as a complementary tool to help identify the species and its stages, along with geographical variability. This could greatly accelerate forensic investigations, eliminating the need to allow the fly larvae to develop until adult stage in order to confirm the species identity and sample origin. © The Authors 2016. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Experimental investigation of HFC407C/HC290/HC600a mixture in a window air conditioner

International Nuclear Information System (INIS)

Jabaraj, D.B.; Avinash, P.; Lal, D. Mohan; Renganarayan, S.

2006-01-01

HCFC22, one of the widely used refrigerants in window air conditioners must be phased out soon as per the Montreal protocol. Presently, HFC407C is considered as a potential drop in substitute for HCFC22, but retrofitting HCFC22 systems with HFC407C with polyol ester oil (POE) is a major issue as HFC407C is immiscible with mineral oil. The miscibility issue of HFC407C with mineral oil was overcome with the addition of a HC blend to it. The above technoeconomic feasibility issues to retrofit the existing HCFC22 systems with an ozone friendly refrigerant and retain the energy efficiency of the system are challenges in the air conditioning sector. In this present work, an experimental analysis has been conducted in a window air conditioner retrofitted with eco-friendly refrigerant mixtures of HFC407C/HC290/HC600a without changing the mineral oil. Its performance, as well as energy consumption, was compared with the conventional one. It is observed that the mixtures demand lengthening of the condenser in order to maintain the discharge pressure within acceptable limits. This also resulted in better heat transfer at the condenser. Therefore, in this study, the condenser tube length was increased by 19% to suit the mixtures as compared to HCFC22. Compared to HCFC22, the refrigeration capacity of the new mixture was 9.54-12.76% higher than that of HCFC22, while the actual COP was found to be 11.91-13.24% higher than that of HCFC22. The overall performance has proved that the HFC407C/HC blend refrigerant mixture could be an eco-friendly substitute to phase out HCFC22

Parameters of the Two-Phase Sand-Air Stream in the Blowing Process

Directory of Open Access Journals (Sweden)

J. Danko

2012-12-01

Full Text Available Theoretical problems concerning the determination of work parameters of the two-phase sand-air stream in the cores making process byblowing methods as well as experimental methods of determination of the main and auxiliary parameters of this process decisive on thecores quality assessed by the value and distribution of their apparent density are presented in the paper. In addition the results of visualisations of the core-box filling with the sand-air stream, from the blowing chamber, obtained by the process filming by means of the quick-action camera are presented in the paper and compared with the results of simulation calculations with the application of the ProCast software.

Experimental performance of R432A to replace R22 in residential air-conditioners and heat pumps

International Nuclear Information System (INIS)

Park, Ki-Jung; Shim, Yun-Bo; Jung, Dongsoo

2009-01-01

In this study, thermodynamic performance of R432A and HCFC22 is measured in a heat pump bench tester under both air-conditioning and heat pumping conditions. R432A has no ozone depletion potential and very low greenhouse warming potential of less than 5. R432A also offers a similar vapor pressure to HCFC22 for 'drop-in' replacement. Test results showed that the coefficient of performance and capacity of R432A are 8.5-8.7% and 1.9-6.4% higher than those of HCFC22 for both conditions. The compressor discharge temperature of R432A is 14.1-17.3 deg. C lower than that of HCFC22 while the amount of charge for R432A is 50% lower than that of HCFC22 due to its low density. Overall, R432A is a good long term 'drop-in' environmentally friendly alternative to replace HCFC22 in residential air-conditioners and heat pumps due to its excellent thermodynamic and environmental properties

Evolution PDEs with nonstandard growth conditions existence, uniqueness, localization, blow-up

CERN Document Server

Antontsev, Stanislav

2015-01-01

This monograph offers the reader a treatment of the theory of evolution PDEs with nonstandard growth conditions. This class includes parabolic and hyperbolic equations with variable or anisotropic nonlinear structure. We develop methods for the study of such equations and present a detailed account of recent results. An overview of other approaches to the study of PDEs of this kind is provided. The presentation is focused on the issues of existence and uniqueness of solutions in appropriate function spaces, and on the study of the specific qualitative properties of solutions, such as localization in space and time, extinction in a finite time and blow-up, or nonexistence of global in time solutions. Special attention is paid to the study of the properties intrinsic to solutions of equations with nonstandard growth.

Nanofiber production of poly (vinylidene fluoride) / hexaferrite, obtained by Blow Spinning Technique; Producao de nanofibras de poli (fluoreto de vinilideno)/hexaferrita, obtidos pela tecnica Blow Spinning

Energy Technology Data Exchange (ETDEWEB)

Dias, G.C.; Zadorosny, L.; Malmonge, J.A.; Malmonge, L.F., E-mail: gabriel.fct@gmail.com [Universidade Estadual Paulista Julio de Mesquita Filho (UNESP), Ilha Solteira, SP (Brazil)

2014-07-01

In this study, fibrous films of poly (vinylidene fluoride) - PVDF with barium hexaferrite particles were obtained by Solution Blow Spinning technique. In such technique, the polymer solution is injected through an inner nozzle which experiences the action of an accelerated flux of gas that drags and stretches the jet solution forming the nanofibers. The films were obtained from solutions of PVDF/DMF (30% w/v), which was incorporated into barium hexaferrite particles in proportions of 1, 3 and 5% (w / w). The results of the micrographs revealed the formation of a fibrous film with good dispersion of the particles. Xray analyzes showed the predominance of the β crystalline phase of PVDF. The increase of the amount of particles induces the appearance of a characteristic peak of PVDF. EDX measurements confirmed the presence of particles in the films. (author)

The Toshiba Blow-Down MHD Test Facility, and Experiments on Non-Equilibrium Ionization

International Nuclear Information System (INIS)

Yamamoto, Y.; Ogiwara, H.; Shioda, S.; Miyata, M.; Goto, M.; Kasahara, E.

1968-01-01

The Toshiba blow-down MHD test facility, which was constructed in 1966 and has operated successfully in many experiments, is described. Operating conditions achieved are: the working gas is helium seeded with potassium, the maximum mass flow being 80 g/sec, the maximum seed fraction 0.1%; the gas static lies between temperature 1200 and 1700°K, the static pressure between 2.0 ∼ 1.2 atm, the velocity of gas in the generator channel between 1000 and 200 m/sec; the duration is up to 30 sec; the magnetic field is 2.7 T; the impurity of working gas is below 150 ppm. (author)

OCONUS Compliance Assessment Protocols Air Force Supplement

Science.gov (United States)

2009-09-01

32-4 Chlormephos 24934-91-6 Chlormequat chloride 999-81-5 1-Chloro-1,1- difluoroethane (HCFC 142(b)) 75-68-3 1-Chloro-2,3- epoxypropane 106-89-8... difluoroethane (HCFC-132b) 1649-08-7 2,2-Dichloro-1,1,1-tri-fluoroethane (HCFC 123) 306-83-2 Dichloran 99-30-9 p-Dichlorobenzene 106-46-7 1,4

Thermodynamic comparision of R744/R600a and R744/R600 used in mid-high temperature heat pump system

Directory of Open Access Journals (Sweden)

Fan Xiao-Wei

2014-01-01

Full Text Available The mid-high temperature heat pump provides hot water at a relatively high temperature using some industrial waste heat as its source. Now, the main refrigerants in this application are CFC114, HCFC123, and HCFC142b, etc., which are scheduled to be phased out due to their high ozone depletion potential and global warmth potential. Some studies have been conducted to find an eco-friendly alternative. In this paper, the natural non-azeotropic mixtures R744/R600a and R744/R600 are analyzed as alternatives. The performance of the heat pump system using new mixture is discussed and compared with those with CFC114, HCFC123, and HCFC142b. Under the given operating conditions, the maximum heating COP should occur at the mass fractions of 18/82 for R744/R600a and 10/90 for R744/R600. Both of their COP are higher than those with the refrigerants of CFC114, HCFC123, and HCFC142b. The COP and volumetric heating capacity of the system with R744/R600a are superior to those with R744/R600.

Simulation on Effect of Preform Diameter in Injection Stretch Blow Molding

Science.gov (United States)

Tan, Z. Q.; Rosli, Nurrina; Oktaviandri, Muchamad

2018-03-01

Polyethylene terephthalate (PET) is the most common material of resin for manufacturing plastic bottle by injection stretch blow molding due to its excellent properties. As various issues of health and environmental hazards due to the PET use have risen, PET bottle manufacture may be improved by minimizing the wall thickness to reduce the PET use. One of the critical qualifications of the manufacturing process which lead to the wall thickness distribution is the initial preform diameter. In this project, we used the ANSYS Polyflow with aim to evaluate the wall thickness distribution of PET bottle for different diameter of initial preform. As a result, only 4 mm preform diameter presented wall thickness below than 1 mm. On the other hand, at least 6 mm preform diameter can permit the wall thickness 1.3 mm i.e. at the shoulder area.

A revised geological range (Late Pliocene) for foraminifer taxon Bolliella adamsi Banner et Blow, 1959

Science.gov (United States)

Reddy, A. Nallapa; Nagendra, R.

2017-12-01

The foraminifer taxon Bolliella adamsi Banner et Blow, 1959 is found to co-occur with index planktic foraminifer taxa of the Late Pliocene (Zone N21) in a core of 2.60 m at 1300 m water depth off Tuticorin, Bay of Bengal. This taxon has been previously known as a Holocene taxon of the Indo-Pacific province. This study significantly revises the known stratigraphic range of B. adamsi from the Late Pliocene (uppermost part of Zone N21) to the Holocene in the Bay of Bengal area.

Ultra low density biodegradable shape memory polymer foams with tunable physical properties

Science.gov (United States)

Singhal, Pooja; Wilson, Thomas S.; Cosgriff-Hernandez, Elizabeth; Maitland, Duncan J.

2017-12-12

Compositions and/or structures of degradable shape memory polymers (SMPs) ranging in form from neat/unfoamed to ultra low density materials of down to 0.005 g/cc density. These materials show controllable degradation rate, actuation temperature and breadth of transitions along with high modulus and excellent shape memory behavior. A method of m ly low density foams (up to 0.005 g/cc) via use of combined chemical and physical aking extreme blowing agents, where the physical blowing agents may be a single compound or mixtures of two or more compounds, and other related methods, including of using multiple co-blowing agents of successively higher boiling points in order to achieve a large range of densities for a fixed net chemical composition. Methods of optimization of the physical properties of the foams such as porosity, cell size and distribution, cell openness etc. of these materials, to further expand their uses and improve their performance.

Longitudinal phase space characterization of the blow-out regime of rf photoinjector operation

Directory of Open Access Journals (Sweden)

J. T. Moody

2009-07-01

Full Text Available Using an experimental scheme based on a vertically deflecting rf deflector and a horizontally dispersing dipole, we characterize the longitudinal phase space of the beam in the blow-out regime at the UCLA Pegasus rf photoinjector. Because of the achievement of unprecedented resolution both in time (50 fs and energy (1.0 keV, we are able to demonstrate some important properties of the beams created in this regime such as extremely low longitudinal emittance, large temporal energy chirp, and the degrading effects of the cathode image charge in the longitudinal phase space which eventually leads to poorer beam quality. All of these results have been found in good agreement with simulations.

Improvement of blow down model for LEAP code

International Nuclear Information System (INIS)

Itooka, Satoshi; Fujimata, Kazuhiro

2003-03-01

In Japan Nuclear Cycle Development Institute, the improvement of analysis method for overheating tube rapture was studied for the accident of sodium-water reactions in the steam generator of a fast breeder reactor and the evaluation of heat transfer condition in the tube were carried out based on study of critical heat flux (CHF) and post-CHF heat transfer equation in Light Water Reactors. In this study, the improvement of blow down model for the LEAP code was carried out taking into consideration the above-mentioned evaluation of heat transfer condition. Improvements of the LEAP code were following items. Calculations and verification were performed with the improved LEAP code in order to confirm the code functions. The addition of critical heat flux (CHF) by the formula of Katto and the formula of Tong. The addition of post-CHF heat transfer equation by the formula of Condie-BengstonIV and the formula of Groeneveld 5.9. The physical properties of the water and steam are expanded to the critical conditions of the water. The expansion of the total number of section and the improvement of the input form. The addition of the function to control the valve setting by the PID control model. (author)

Global existence and blow-up phenomena for two-component Degasperis-Procesi system and two-component b-family system

OpenAIRE

Liu, Jingjing; Yin, Zhaoyang

2014-01-01

This paper is concerned with global existence and blow-up phenomena for two-component Degasperis-Procesi system and two-component b-family system. The strategy relies on our observation on new conservative quantities of these systems. Several new global existence results and a new blowup result of strong solutions to the two-component Degasperis- Procesi system and the two-component b-family system are presented by using these new conservative quantities.

Mutations in THAP11 cause an inborn error of cobalamin metabolism and developmental abnormalities.

Science.gov (United States)

Quintana, Anita M; Yu, Hung-Chun; Brebner, Alison; Pupavac, Mihaela; Geiger, Elizabeth A; Watson, Abigail; Castro, Victoria L; Cheung, Warren; Chen, Shu-Huang; Watkins, David; Pastinen, Tomi; Skovby, Flemming; Appel, Bruce; Rosenblatt, David S; Shaikh, Tamim H

2017-08-01

CblX (MIM309541) is an X-linked recessive disorder characterized by defects in cobalamin (vitamin B12) metabolism and other developmental defects. Mutations in HCFC1, a transcriptional co-regulator which interacts with multiple transcription factors, have been associated with cblX. HCFC1 regulates cobalamin metabolism via the regulation of MMACHC expression through its interaction with THAP11, a THAP domain-containing transcription factor. The HCFC1/THAP11 complex potentially regulates genes involved in diverse cellular functions including cell cycle, proliferation, and transcription. Thus, it is likely that mutation of THAP11 also results in biochemical and other phenotypes similar to those observed in patients with cblX. We report a patient who presented with clinical and biochemical phenotypic features that overlap cblX, but who does not have any mutations in either MMACHC or HCFC1. We sequenced THAP11 by Sanger sequencing and discovered a potentially pathogenic, homozygous variant, c.240C > G (p.Phe80Leu). Functional analysis in the developing zebrafish embryo demonstrated that both THAP11 and HCFC1 regulate the proliferation and differentiation of neural precursors, suggesting important roles in normal brain development. The loss of THAP11 in zebrafish embryos results in craniofacial abnormalities including the complete loss of Meckel's cartilage, the ceratohyal, and all of the ceratobranchial cartilages. These data are consistent with our previous work that demonstrated a role for HCFC1 in vertebrate craniofacial development. High throughput RNA-sequencing analysis reveals several overlapping gene targets of HCFC1 and THAP11. Thus, both HCFC1 and THAP11 play important roles in the regulation of cobalamin metabolism as well as other pathways involved in early vertebrate development. © The Author 2017. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Steam condensation behavior of high pressure water's blow down directly into water in containment under LOCA

International Nuclear Information System (INIS)

Kusunoki, Tsuyoshi; Ishida, Toshihisa; Yoritsune, Tsutomu; Kasahara, Y.

1995-01-01

JAERI has been conducting a design study of an advanced type Marine Reactor X (MRX) for merchant ships. By employing 'Integral type PWR', In-vessel type control rod drive systems', 'Water filled containment system' and 'Decay heat removal system by natural convection', MRX achieved a compact, light weight and highly safe plant. Experiments on steam condensation behavior of high pressure water's blow down into water have been conducted in order to investigate a major safety issue related to the design decision of 'Water filled containment system'. (author)

Potential of anticlostridial Lactobacillus isolated from cheese to prevent blowing defects in semihard cheese

DEFF Research Database (Denmark)

Christiansen, Pia; Vogensen,, F. K.; Nielsen, E. W

2010-01-01

Five anticlostridial Lactobacillus strains isolated from cheese were selected for a mixed adjunct culture. Cheese with the mixed adjunct culture (experimental) and without (control) was made in triplicate and ripened as vacuum-packed and surface-ripened cheese. Cheese gross composition was similar....... Excessive gas formation occurred only in control cheeses. In contrast to control cheeses, the experimental cheeses were dominated by the added adjunct Lactobacillus strains (repetitive-PCR). Casein breakdown was not influenced, however, the total amount of amino acids and pH was slightly lower...... in the experimental cheeses. Anticlostridial nonstarter Lactobacillus strains have potential as protective adjunct cultures against blowing defects in cheese....

Numerical modeling of plasma plume evolution against ambient background gas in laser blow off experiments

International Nuclear Information System (INIS)

Patel, Bhavesh G.; Das, Amita; Kaw, Predhiman; Singh, Rajesh; Kumar, Ajai

2012-01-01

Two dimensional numerical modelling based on simplified hydrodynamic evolution for an expanding plasma plume (created by laser blow off) against an ambient background gas has been carried out. A comparison with experimental observations shows that these simulations capture most features of the plasma plume expansion. The plume location and other gross features are reproduced as per the experimental observation in quantitative detail. The plume shape evolution and its dependence on the ambient background gas are in good qualitative agreement with the experiment. This suggests that a simplified hydrodynamic expansion model is adequate for the description of plasma plume expansion.

Morphological comparison between Chrysomya rufifacies (Macquart) and Chrysomya villeneuvi Patton (Diptera: Calliphoridae) puparia, forensically important blow flies.

Science.gov (United States)

Sukontason, Kabkaew L; Narongchai, Paitoon; Kanchai, Chaturong; Vichairat, Karnda; Piangjai, Somsak; Boonsriwong, Worachote; Bunchu, Nophawan; Sripakdee, Duanghatai; Chaiwong, Tarinee; Kuntalue, Budsabong; Siriwattanarungsee, Sirisuda; Sukontason, Kom

2006-12-20

In Thailand, the hairy maggots of the blow flies, Chrysomya rufifacies (Macquart) and Chrysomya villeneuvi Patton, are of forensic importance. Both flies are closely related species, not only in the morphological appearance of their larvae and puparia, but also on the aggressive feeding habit of the former. In our continuing studies of forensically important flies, identification of immature ones needs particular attention. In this study, we reported the morphological comparison between the puparia of these two blow fly species using scanning electron microscopy (SEM). Observation revealed that the cuticular sculpture of tubercles along the dorsal and lateral segments had markedly different features: with C. rufifacies having many sharp spines assembling only at the tip, while of C. villeneuvi bore stout spines throughout the tubercle. A larger number of globules at the bubble membrane on the dorsolateral border of the fifth segment was found in C. villeneuvi (average 225) than in C. rufifacies (average 35), and more papillae was observed on the anterior spiracle in C. villeneuvi (13-15) than in C. rufifacies (9-12). However, the morphology of distinct net-like patches of the integument and structure of the posterior spiracle of both species were almost identical. Morphological comparison in this study permitted identification of the puparia of both fly species, particularly in areas where they co-exist.

Expanding the Adoption on Private Lands : Blowing-and-Drifting Snow Control Treatments and the Cost Effectiveness of Permanent versus Non-Permanent Treatment Options

Science.gov (United States)

2017-11-01

Previous research that estimated the costs and benefits of snow-fences for MnDOT in terms of a reduction in the costs of mitigating blowing-and-drifting snow problem areas (MN/RC 2012-03) demonstrated the ability of snow-fences to significantly lower...

Melting of corrosion–resisting steels using air in bath agitation at the end of oxygen blowing

International Nuclear Information System (INIS)

Gizatulin, R A; Valuev, D V; Valueva, A V; Yedesheva, Ch V

2014-01-01

A number of metallurgical plants employ ladle stirring with argon at the end of oxygen blowing during the melting process of corrosion–resisting steels [1, 2]. At the same time, the scarcity and relatively high cost of argon, its low pressure in a shop air pipeline restrain most plants from using argon for corrosion–resisting steel production. Compressed air was used instead of argon to intensify the process of decarbonizing when chromium–nickel stainless steels were made with a 40–ton electric arc furnace at the Kuznetsk Metallurgical Plant

A critical blow-up exponent in a chemotaxis system with nonlinear signal production

Science.gov (United States)

Winkler, Michael

2018-05-01

This paper is concerned with radially symmetric solutions of the Keller–Segel system with nonlinear signal production, as given by in the ball for and R  >  0, where f is a suitably regular function generalizing the prototype determined by the choice , , with . The main results assert that if in this setting the number κ satisfies then for any prescribed mass level m  >  0, there exist initial data u 0 with , for which the solution of the corresponding Neumann initial-boundary value problem blows up in finite time. The condition in () is essentially optimal and is indicated by a complementary result according to which in the case , for widely arbitrary initial data, a global bounded classical solution can always be found.

Electron density profile determination by means of laser blow-off injected neutral beam

International Nuclear Information System (INIS)

Kocsis, G.; Bakos, J.S.; Ignacz, P.N.; Kardon, B.; Koltai, L.; Veres, G.

1992-01-01

This paper is devoted to the experimental and theoretical studies of the determination of the electron density profiles by means of laser blow-off neutrals. For the determination of the density profile the time and spatial distributions of the spectral line radiation intensity of the injected neutrals are used. The method is compared to other previously proposed methods and the advantages and disadvantages of the different methods are discussed. The result of the comparison is that our method gives the most reliable result with the highest temporal resolution for the density profile of the edge plasma. The only disadvantage is the need of careful calibration of the sensitivity of the spatial channels. The advantage is the ability of the method as a standard diagnostic. (orig.)

Use of the theory of recognition of patterns in developing methane metering equipment for blow-out-dangerous mines. [Instrument recognizes rate of change of methane concentration and, if dangerous, shuts off electrical equipment

Energy Technology Data Exchange (ETDEWEB)

Medvedev, V N

1978-01-01

In the most general form, the existing methane-metering equipment which issues command signals when the maximum permissible value of methane concentration has been reached can be viewed as a recognition system. The algorithm for operation on the principle of evaluating the degree of blow-out danger of the ore atmosphere stipulates the recognition of two situations: 1) ''not dangerous ''(methane concentration below maximum permissible value); 2) ''dangerous'' (disorders in technological process; methane concentration above maximum permissible value). This approach for constructing means for gas protection is optimal only for mines working beds which are not dangerous for sudden blow-outs. However, if we ''train'' the apparatus to recognize what was the reason for increase in methane concentration, ways are afforded for solving the problem of creating an effective methane-metering equipment for mines with sudden blow-outs. Gas-dynamic processes with sudden blow-outs can be distinguished from standard technological, in particular, according to the rate in increase in methane concentration. On this basis, functional plan is proposed for constructing the automatic gas protection for explosiondangerous mines which includes a primary measurement of methane concentration, block of concentration control, block of process recognition, block of command signals, block of information delay, block of measuring the rate of methane concentration, threshold device for the rate of increase in concentration.

Nanofiber production of poly (vinylidene fluoride) / hexaferrite, obtained by Blow Spinning Technique

International Nuclear Information System (INIS)

Dias, G.C.; Zadorosny, L.; Malmonge, J.A.; Malmonge, L.F.

2014-01-01

In this study, fibrous films of poly (vinylidene fluoride) - PVDF with barium hexaferrite particles were obtained by Solution Blow Spinning technique. In such technique, the polymer solution is injected through an inner nozzle which experiences the action of an accelerated flux of gas that drags and stretches the jet solution forming the nanofibers. The films were obtained from solutions of PVDF/DMF (30% w/v), which was incorporated into barium hexaferrite particles in proportions of 1, 3 and 5% (w / w). The results of the micrographs revealed the formation of a fibrous film with good dispersion of the particles. Xray analyzes showed the predominance of the β crystalline phase of PVDF. The increase of the amount of particles induces the appearance of a characteristic peak of PVDF. EDX measurements confirmed the presence of particles in the films. (author)

A Digital System for Longitudinal Emittance Blow-Up in the LHC

CERN Document Server

JaussI, M; Baudrenghien, P; Butterworth, A; Sanchez-Quesada, J; Shaposhnikova, E; Tuckmantel, J

2011-01-01

In order to preserve beam stability with nominal bunch intensity in the LHC, longitudinal emittance blow-up is performed during the energy ramp by injecting phase noise in the main accelerating cavities. The noise spectrum spans a small frequency band around the synchrotron frequency. It is generated continuously in software and streamed digitally into the Digital Signal Processor (DSP) of the Beam Control system where it is added to the pick-up signal of the beam phase loop, resulting in a phase modulation of the accelerating RF. In order to achieve reproducible results, a feedback system, using as input the measured bunch lengths averaged over each ring, controls the strength of the excitation, allowing the operator to simply set a target bunch length. The spectrum of the noise is adjusted to excite the core of the bunch only, extending to the desired bunch length. As it must follow the evolution of the synchrotron frequency through the ramp, it is automatically calculated by the LHC settings management sof...

French studies on blow-down accident in light water reactors

International Nuclear Information System (INIS)

Pelce, J.

1977-01-01

The effects on fuel elements and containment buildings resulting from a rapid blow-down accident and the effectiveness of proposed emergency systems are currently being evaluated in France, using the so-called first generation computer codes. Some of these were developed by the constructing organization Framatome for the design of actual power plants; others were developed by the Nuclear Safety Division to back-up related safety studies. These codes are considered to be inadequate and for several years a large effort has been made jointly by EDF and safety authorities, and with the technical assistance of CEA, to make a significant improvement in the methods of assessment. Framatome also participates in this work to some extent. A more physical method is proposed. In particular, selected models are supported by a quite comprehensive experimental programme which is mainly analytical in nature, as follows: (1) Basic analysis, using experiments which are planned or in progress, such as CANON, MOBY-DICK, SUPER MOBY-DICK, REBECA (critical flow at the break and between sub-compartments of the containment building), ECOTRA (condensation on inner walls), TAPIOCA (phase separation at small cracks), EPIS (water and steam mixing during emergency injection), EDGAR (fuel cladding behavior). (2) More intricate or semi-integral analysis such as OMEGA and ERSEC (tests on in-core heat transfer during blow-down and rewetting), both of which are in progress, in-pile PHEBUS loop due to start operating in 1977 (fuel behavior during the accident), pump tests (EVA, POMPE). Future methods of assessing the reactor itself will include the physical models thus perfected: A first code, (CLYSTERE) has been written and can be used. Although it has not been validated experimentally, it can already evaluate the effect of some physical phenomena on the development of the accident. Work is being done on reconstructing the general flow chart of this code in order to improve the conditions of use, in

Diagnosis of blow-out fracture of the orbital floor using a computed tomography

International Nuclear Information System (INIS)

Ishikawa, Yoshimi; Aoki, Shinjiroh; Ono, Shigeru; Fujita, Kiyohide

1986-01-01

Diagnosis of a blow-out fracture of the orbital floor is relatively easy from clinical and roentogen findings but information from these findings are not adequate for the decision for surgical indication. Until recently, computed tomography for the orbital region was generally performed only in axial plane. But the axial plane is parallel to the orbital structure, therefore it is difficult to visualize the orbital floor and inferior rectus muscle. On the other hand, coronal plane is cross-section to the orbital structure, and we can visualize the all orbital soft tissues including extraocular muscles. We examined 3 cases diagnosed as a blow-out fracture of the orbital floor by conventional roentogen films and clinical findings. After axial CT was performed firstly, the coronal CT was scanned with 60 degrees to 70 degrees from OM line, setting the patient in the hanging head position. Case 1 used coronal reformation of the axial CT data. Case 2 and case 3 used direct coronal scanning. By bi-plane CT we could diagnose whether inferior rectus muscle was entrapped or not, and confirm surgical indication. Using of a cadaver, we studied the mechanism for limitation of eye movement. These studies revealed that it is rare that the inferior rectus muscle is entrapped directly by fractured segments at the orbital anterior floor. Because there is a lot of orbital fat-pad between the inferior rectus muscle and the orbital floor, and it may play an important role. The limited mobility of the inferior rectus muscle may occur as a result of increased tension of the fibrous bands that attach to the muscle sheath from the prolapsed fat-pad, and contructure by scar formed secondarily. Diagnosis of the location of a fracture in the orbital floor and cause of the limitation of eye movement must be done as early as possible and from this information we can confirm surgical indication. (J.P.N.)

ANALISIS KELAYAKAN FINANSIAL PROYEK NARROWNECK PRESS AND BLOW UNTUK PROSES PRODUKSIBOTOL MINUMAN BERENERGI DI PT. ABC

Directory of Open Access Journals (Sweden)

Toni MT Munthe

2015-08-01

Full Text Available PT. ABC merupakan salah satu pabrik yang memproduksi botol kemasan kaca. Penelitian ini bertujuan untuk mengetahui layak atau tidaknya rencana investasi pada proyek Narrow Neck Press and Blow secara finansial di PT. ABC pada periode bulan April 2014 hingga bulan Juni 2014. Analisis kelayakan finansial proyek Narrow Neck Press and Blow, menggunakan metode analisis Net Present Value, Internal Rate of Return, Payback Period dan Sensitivity Analysis. Perbedaan antara nilai sekarang dari semua kas masuk dengan nilai sekarang dari semua kas keluar dari suatu proyek atau suatu investasi diperoleh dengan metode NPV, sedangkan untuk mencari tingkat bunga yang menyamakan nilai sekarang dari aliran kas bersih dan investasi diperoleh dengan metode IRR. Metode analisis yang dapat digunakan untuk mengetahui berapa lamakah waktu yang diperlukan untuk menutup dana yang dikeluarkan untuk suatu proyek dapat diperoleh dengan metode Payback Period. Setelah itu, dilakukan pengujian menggunakan sensitivitas analisis untuk mengetahui tingkat sensitivitas untuk tiap-tiap parameter terhadap persentase kenaikan dan penurunan. Dari hasil analisis data diperoleh nilai NPV sebesar Rp. 1.179.728.649.900,06, nilai IRR sebesar 56,36% dan periode pengembalian terletak pada 2 tahun 2 bulan 9 hari. Dengan menggunakan analisis sensitivitas dapat diketahui bahwa proyek ini sangat sensitif terhadap penurunan volume produksi. Berdasarkan hasil perhitungan, titik impas akan dicapai apabila volume produksi 213.403.267 unit per tahun atau 88,92% dari volume produksi awal. Nilai ini menunjukkan bahwa apabila volume produksi pada suatu periode mengalami penurunan lebih dari 11,08% dari volume produksi awal, maka investasi tersebut akan merugikan.

Variability of Blowing Dust Weather Frequency over Semi-Arid Areas of China (Baicheng, Jilin Province and Relationships with Climatic Factors During 1951 - 2006

Directory of Open Access Journals (Sweden)

Yun-Fei Wu

2011-01-01

Full Text Available We analyzed the variability of blowing dust weather frequency (BDWF and patterns in climatic factors over Baicheng for the period 1951 - 2006 in this study. The data showed that blowing dust over Baicheng occurs intensively during the spring and shows significant inter-decadal variability. One of the main findings is that the occurrence of blowing dust has significantly decreased after the mid-1980s. The mean wind speed (WS, diurnal temperature range (DTR, relative humidity (RH and precipitation at Baicheng during the spring show decreasing trends. The decreasing trends of the mean WS and DTR are significant at 99% confidence levels according to the t-test; the dataset also indicated a sharp decrease in WS occurred after the mid-1980s. The mean surface air temperature (SAT escalated in a fluctuating manner during 1951 - 2006. BDWF at Baicheng was significantly related to local WS, SAT and DTR during the spring [correlation coefficients (CCs are 0.41, -0.47 and 0.36, respectively]. The correlation between BDWF at Baicheng and selected climatic factors over the sand-dust source regions and transmission paths were also calculated. We found that BDWF is well correlated to the mean WS and SAT during the spring, with CCs of 0.45 and -0.48, respectively. The most likely causes for the dramatic decrease observed in BDWF after the mid-1980s were related to the adjustment of large-scale circulation patterns in response to a decrease of meridional temperature differences, the weakening of steering westerlies and the strengthening of downward motions that has occurred at the middle latitudes of eastern Eurasia in recent decades.

Compressed Air System Modifications Improve Efficiency at a Plastics Blow Molding Plant (Southeastern Container Plant): Office of Industrial Technologies (OIT) BestPractices Technical Case Study

Energy Technology Data Exchange (ETDEWEB)

Wogsland, J.

2001-06-18

This case study is one in a series on industrial firms who are implementing energy efficient technologies and system improvements into their manufacturing processes. This case study documents the activities, savings, and lessons learned on the plastics blow molding plant project.

OPTIMASI PROSES MESIN STRETCH BLOW MOULDING PADA BOTOL 600 ML DENGAN METODE RSM (RESPONSE SURFACE METHODOLOGY STUDI KASUS DI PT. UNIPLASTINDO INTERBUANA

Directory of Open Access Journals (Sweden)

Mochamad Mas'ud

2017-04-01

Full Text Available Pada proses produksi Aqua botol plastik 600 ml menggunakan mesin stretch blow moulding dengan sistem pneumatik, Pembuatan produk dengan menggunakan mesin ini memiliki faktor-faktor yang dapat mempengaruhi kualitas botol yang dihasilkan . Penyimpangan ukuran (pemerataan tebal botol dan kemiringan botol tidak sesuai dengan spesifikasi mengakibatkan botol dibagian pundak putih dan bergelang (shrinkage. Tujuan dari penelitian ini yaitu mengoptimalkan setting parameter mesin stretch blow moulding agar menghasilkan kualitas baik pada produk botol plastik 600 ml. Adapun variable(prediktor yang di pilih yaitu preblow (bar, preform temperature (, dan P1 point (mm, sedangkan respon yang dicari yaitu kemiringan minimal dan tebal maksimal. Metode yang di gunakan dalam penelitian ini yaitu menggunakan Response Surface Metodhology (RSM yang mana dalam perhitungannya menggunakan software minitab 16. Dengan menggunakan Box Behnken Design dan 3 level factorial di hasilkan run 15 percobaan. Berdasarkan hasil kondisi yang optimal parameter yaitu preblow sebesar 6,5 bar, preform temperature sebesar 114 , dan P1 Point sebesar 25 mm. Dengan setting sebesar tersebut akan menghasilkan respon tebal botol sebesar 0,1446 dan kemiringan botol sebesar 0,1875.

Nonlinear parabolic equations with blowing-up coefficients with respect to the unknown and with soft measure data

Directory of Open Access Journals (Sweden)

Khaled Zaki

2016-12-01

Full Text Available We establish the existence of solutions for the nonlinear parabolic problem with Dirichlet homogeneous boundary conditions, $$ \\frac{\\partial u}{\\partial t} - \\sum_{i=1}^N\\frac{\\partial}{\\partial x_i} \\Big( d_i(u\\frac{\\partial u}{\\partial x_i} \\Big =\\mu,\\quad u(t=0=u_0, $$ in a bounded domain. The coefficients $d_i(s$ are continuous on an interval $]-\\infty,m[$, there exists an index p such that $d_p(u$ blows up at a finite value m of the unknown u, and $\\mu$ is a diffuse measure.

MODERNIZATION OF TECHNOLOGICAL LINE FOR CELLULAR EXTRUSION PROCESS

Directory of Open Access Journals (Sweden)

Tomasz Garbacz

2014-06-01

As part of the modernization of the cellular extrusion technology the extrusion head was designed and made. During the designing and modeling of the head the Auto CAD programe was used. After the prototyping the extrusion head was tested. In the article specification of cellular extrusion process of thermoplastics was presented. In the research, the endothermal chemical blowing agents in amount 1,0% by mass were used. The quantity of used blowing agent has a direct influence on density and structure of the extruded product of modified polymers. However, these properties have further influence on porosity, impact strength, hardness, tensile strength and another.

Energy and global warming impacts of CFC alternative technologies

International Nuclear Information System (INIS)

Fischer, S.K.; Fairchild, P.D.; Hughes, P.J.

1992-01-01

Chlorofluorocarbons (CFCs) are used in a number of applications, and volumes of CFCs used grew at a tremendous pace during the 1960s and 1970s. However, in the mid-1980s, it was confirmed that these extremely useful chemicals contribute to the destruction of stratospheric ozone. These chemicals are being phased out of use rapidly to protect the ozone layer and it is very important that the replacements for CFSs do not result in a net increase in global warming by introducing less efficient processes that lead to higher energy use and increased carbon dioxide emissions. A study was conducted to identify those alternative chemicals and technologies that could replace CFCs in energy related applications before the year 2000, and to assess the total potential impact of these alternatives on global warming. The analysis for this project included an estimate of the direct effects from the release of blowing agents, refrigerants, and solvents into the atmosphere and the indirect effects in the form of carbon dioxide emissions resulting from energy use for commercial and residential heating and cooling, household and commercial refrigeration, building and automobile air-conditioning, and general metal and electronics solvent cleaning. The discussion in this paper focuses on those aspects of the study relevant to refrigeration and air-conditioning. In general the use of hydrofluorocarbon (HFC) and hydrochlorofluorocarbon (HCFC) alternatives for CFCs lead to large and sometimes dramatic reduction in total equivalent warming impact (TEWI), lifetime equivalent CO 2 emission. Most of the reductions result from decreased direct effects without significant changes in energy use. 3 refs., 3 figs., 1 tab

TEWI Analysis: Its Utility, Its Shortcomings, and Its Results

International Nuclear Information System (INIS)

Baxter, V.D.; Fischer, S.K.; Sand, J.R.

1999-01-01

The past decade has been a challenging time for the refrigeration and air conditioning industry worldwide. Provisions of the Montreal Protocol and its amendments require the phaseout of chlorofluorocarbon (CFC) and hydrochlorofluorocarbon (HCFC) compounds that have been used extensively as insulating foam blowing agents and refrigerants in refrigeration systems, heat pumps, and air conditioners. In response, hydrofluorocarbon (HFC) compounds were proposed, developed, and are starting to be used as the primary alternatives to CFCs and HCFCs. However, in 1997 under the Kyoto Protocol, industrialized nations have agreed to roll back emissions of HCFCs, carbon dioxide (CO*), and four other greenhouse gases which threaten to cause excessive global warming. The US. Department of Energy and the Alternative Fluorocarbon Environmental Acceptability Study (AFEAS) jointly sponsored research projects to identify the major applications of CFCs, HCFCs, and HFCs and to examine the impacts of these compounds and the energy use of applications employing these compounds on global warming. The five major uses of fluorocarbons based on sales were automobile air conditioning, supermarket refrigeration, unitary heat pumps and air conditioning, chillers for cooling large office buildings, and household refrigeration. Almost all of the refrigerants used in these applications are global warming gases, and if the refrigerant leaks out of the system during operation, is lost during maintenance or is not recovered when the system is scraped, it contributes to global warming. But, it is also true that the energy consumed by refrigeration and air conditioning systems, in the form of electricity or the direct combustion of fossil fuel, results in the release of CO*, the primary cause of atmospheric global warming

Keys to the blow flies of Taiwan, with a checklist of recorded species and the description of a new species of Paradichosia Senior-White (Diptera, Calliphoridae

Directory of Open Access Journals (Sweden)

Shih-Tsai Yang

2014-08-01

Full Text Available Blow flies (Diptera: Calliphoridae show a great diversity in behavior and ecology, play important roles in ecosystems, and have medical and forensic importance to humans. Despite this, the taxonomy and classification of Taiwan's Calliphoridae have rarely been studied. In this study, specimens of Taiwanese calliphorids were collected and carefully studied, and all 76 species recorded in Taiwan are listed following the identification keys. Dichotomous keys to all subfamilies, tribes, genera, and species of blow flies recorded in Taiwan are provided, including 16 species that are newly recorded from Taiwan. In addition, one new species of the genus Paradichosia Senior-White is described and illustrated. We also discuss the morphological differences between the specimens of Silbomyia hoeneana Enderlein collected from China and Taiwan, a species that has only been found previously in Southern China.

Keys to the blow flies of Taiwan, with a checklist of recorded species and the description of a new species of Paradichosia Senior-White (Diptera, Calliphoridae)

Science.gov (United States)

Yang, Shih-Tsai; Kurahashi, Hiromu; Shiao, Shiuh-Feng

2014-01-01

Abstract Blow flies (Diptera: Calliphoridae) show a great diversity in behavior and ecology, play important roles in ecosystems, and have medical and forensic importance to humans. Despite this, the taxonomy and classification of Taiwan's Calliphoridae have rarely been studied. In this study, specimens of Taiwanese calliphorids were collected and carefully studied, and all 76 species recorded in Taiwan are listed following the identification keys. Dichotomous keys to all subfamilies, tribes, genera, and species of blow flies recorded in Taiwan are provided, including 16 species that are newly recorded from Taiwan. In addition, one new species of the genus Paradichosia Senior-White is described and illustrated. We also discuss the morphological differences between the specimens of Silbomyia hoeneana Enderlein collected from China and Taiwan, a species that has only been found previously in Southern China. PMID:25152681

Hydrocarbons as Refrigerants―A Review

Directory of Open Access Journals (Sweden)

J. H. KOH

2017-08-01

Full Text Available Refrigerants used in air conditioning and refrigeration (AC&R indusries have come full circle since the beginning of the industrialrevolution. With concern on issues relating to the environment such as the global warming and climate change issues, we should finda better alternative than to continue using these refrigerants that cause global warming and ozone depletion. AC&R industryplayers have blended in by introducing some new equipment and components that are specificallydesigned for hydrocarbon (HC use. Mostnew refrigerators sold in Malaysia are already equipped with isobutane [a hydrocarbon designated as R-600a by the American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE standards]as refrigerants. Malaysia has ratifiedthe Montreal Protocol and targetted a 10% reduction in hydrochlorofluorocarbon(HCFC consumption, beginning 2016 with the banning of 2.5 horsepower (hp and below in air-conditioning (AC equipment to be used. Instead,hydrofluorocarbon(HFC R-410a was introduced as a replacement for HCFC- 22, whereas in other countries this HFC has been phased down. This article was initiated  because of the difficultin findinga replacement for HCFC. Also, the possibilities of using HC as an alternative to replace HCFC insteadof using HFC as a transitional refrigerant in place of HCFC is reviewed in this article. The performance of HC is very similar to HCFC and flmmability issues could be easily overcome with the use of an effectivedesign. Their use could be facilitated with the adaptation of specific standards and properly enacted legislatio

Local correlations for flap gap oscillatory blowing active flow control technology

Directory of Open Access Journals (Sweden)

Cătălin NAE

2010-09-01

Full Text Available Active technology for oscillatory blowing in the flap gap has been tested at INCAS subsonic wind tunnel in order to evaluate this technology for usage in high lift systems with active flow control. The main goal for this investigation was to validate TRL level 4 for this technology and to extend towards flight testing. CFD analysis was performed in order to identify local correlations with experimental data and to better formulate a design criteria so that a maximum increase in lift is possible under given geometrical constraints. Reference to a proposed metric for noise evaluation is also given. This includes basic 2D flow cases and also 2.5D configurations. In 2.5D test cases this work has been extended so that the proposed system may be selected as a mature technology in the JTI Clean Sky, Smart Fixed Wing Aircraft ITD. Complex post-processing of the experimental and CFD data was mainly oriented towards system efficiency and TRL evaluation for this active technology.

How are soap bubbles blown? Fluid dynamics of soap bubble blowing

Science.gov (United States)

Davidson, John; Lambert, Lori; Sherman, Erica; Wei, Timothy; Ryu, Sangjin

2013-11-01

Soap bubbles are a common interfacial fluid dynamics phenomenon having a long history of delighting not only children and artists but also scientists. In contrast to the dynamics of liquid droplets in gas and gas bubbles in liquid, the dynamics of soap bubbles has not been well documented. This is possibly because studying soap bubbles is more challenging due to there existing two gas-liquid interfaces. Having the thin-film interface seems to alter the characteristics of the bubble/drop creation process since the interface has limiting factors such as thickness. Thus, the main objective of this study is to determine how the thin-film interface differentiates soap bubbles from gas bubbles and liquid drops. To investigate the creation process of soap bubbles, we constructed an experimental model consisting of air jet flow and a soap film, which consistently replicates the conditions that a human produces when blowing soap bubbles, and examined the interaction between the jet and the soap film using the high-speed videography and the particle image velocimetry.

Evaluation of bait traps as a means to predict initial blow fly (Diptera: Calliphoridae) communities associated with decomposing swine remains in New Jersey, USA.

Science.gov (United States)

Weidner, Lauren M; Gemmellaro, M Denise; Tomberlin, Jeffery K; Hamilton, George C

2017-09-01

Information about blow fly (Diptera: Calliphoridae) species distributions can be valuable for criminal investigations, with regards to determining movement of remains from one location to another and time of colonization estimates, making these data extremely useful. Past work has been conducted on initial species community structure across New Jersey, USA using traps baited with beef liver; however, if these same species frequent vertebrate carrion remains unclear. In order to evaluate these data, piglet carcasses were placed out once every two weeks for a year in New Brunswick, New Jersey, USA. The same methods were implemented as those used for traps baited with beef liver, with length of collections being based on ADD values. Seven calliphorid species, Calliphora vicina (Robineau-Desvoidy), Lucilia sericata (Meigen), Lucilia coeruleiviridis (Macquart), Phormia regina (Meigen), Pollenia pediculata Macquart, Pollenia rudis (F.) and Protophormia terraenovae (Robineau-Desvoidy) were collected from the carcasses. During this experiment L. sericata, L. coeruleiviridis and P. regina were the dominant adult blow flies captured, totaling 38.2%, 29.2% and 29.2% respectively of all adults caught. All three species colonized the carcasses as well, although not all were dominant colonizers. C. vicina was recorded ovipositing in December, while the piglet was submerged in approximately 5cm of snow. All species that totaled at least 1% of the total collection (adults captured and larvae reared) were the same across baited traps and carcasses. This study supports the use of beef liver baits for surveying forensically important blow flies and the application of such information to forensic investigations. Copyright © 2017 Elsevier B.V. All rights reserved.

Novel Method of Weighting Cumulative Helmet Impacts Improves Correlation with Brain White Matter Changes After One Football Season of Sub-concussive Head Blows.

Science.gov (United States)

Merchant-Borna, Kian; Asselin, Patrick; Narayan, Darren; Abar, Beau; Jones, Courtney M C; Bazarian, Jeffrey J

2016-12-01

One football season of sub-concussive head blows has been shown to be associated with subclinical white matter (WM) changes on diffusion tensor imaging (DTI). Prior research analyses of helmet-based impact metrics using mean and peak linear and rotational acceleration showed relatively weak correlations to these WM changes; however, these analyses failed to account for the emerging concept that neuronal vulnerability to successive hits is inversely related to the time between hits (TBH). To develop a novel method for quantifying the cumulative effects of sub-concussive head blows during a single season of collegiate football by weighting helmet-based impact measures for time between helmet impacts. We further aim to compare correlations to changes in DTI after one season of collegiate football using weighted cumulative helmet-based impact measures to correlations using non-weighted cumulative helmet-based impact measures and non-cumulative measures. We performed a secondary analysis of DTI and helmet impact data collected on ten Division III collegiate football players during the 2011 season. All subjects underwent diffusion MR imaging before the start of the football season and within 1 week of the end of the football season. Helmet impacts were recorded at each practice and game using helmet-mounted accelerometers, which computed five helmet-based impact measures for each hit: linear acceleration (LA), rotational acceleration (RA), Gadd Severity Index (GSI), Head Injury Criterion (HIC 15 ), and Head Impact Technology severity profile (HITsp). All helmet-based impact measures were analyzed using five methods of summary: peak and mean (non-cumulative measures), season sum-totals (cumulative unweighted measures), and season sum-totals weighted for time between hits (TBH), the interval of time from hit to post-season DTI assessment (TUA), and both TBH and TUA combined. Summarized helmet-based impact measures were correlated to statistically significant changes in

Starch/poly (butylene adipate-co-terephthalate/montmorillonite films produced by blow extrusion

Directory of Open Access Journals (Sweden)

Rodrigo A. L. Santos

2014-07-01

Full Text Available This study aims to prepare biodegradable films from cassava starch, poly (butylene adipate-co-terephthalate (PBAT, and montmorillonite (MMT using blow-extrusion process and analyze the effects of different types and concentrations of MMT on the microstructure, physicochemical, and mechanical properties of the resulting films. The films were produced by blending 30% of PBAT with glycerol (17.5%, starch (49.0-52.5%, and four different types of montmorillonite (Cloisite® Na+, 10A, 15A, and 30B at two different concentrations (1.75% and 3.5%. All the films prepared in this study showed an increase in the basal spacing of MMT layers. In particular, the films with 10A and 30B showed the highest increase in intercalation basal spacing, suggesting the formation of intercalated composites. The addition of nanoclays decreased the elongation of films. The addition of Cloisite® 10A resulted in films with the lowest WVP values and the highest stability to water adsorption under different RH conditions.

The effect of starvation on the larval behavior of two forensically important species of blow flies (Diptera: Calliphoridae).

Science.gov (United States)

Singh, Devinder; Bala, Madhu

2009-12-15

The postfeeding larval stage in blow flies is generally an irreversible condition when the fully grown third instar larvae stop feeding and give no response towards food. The larvae of most species then disperse away from their feeding medium and pupariate. There are several cases reported about the use of postfeeding larvae as forensic evidence. It is a matter of common observation that the postfeeding stage can be reached earlier than the expected time if food becomes unavailable. However, no information is available on whether postfeeding stage induced by scarcity of food is also irreversible. Similarly, the minimum period of development required by the larvae of different blow flies species to enable their survival as postfeeding larvae and pupariation in the absence of food is unknown. It was observed during the present studies that the larvae of two Chrysomya species must feed for at least 35 h at 28 degrees C in order to be capable of reaching the postfeeding stage and subsequent pupariation. Duration of the starvation period required to induce postfeeding behavior decreases with increasing age of larvae. In the case of Chrysomya megacephala, 35, 45, 55 and 65 h old larvae attained irreversible postfeeding stage after 30, 20, 12 and 2 h of starvation, respectively. Similarly, larvae of Chrysomya rufifacies that were 35, 45, 55 and 60 h old attained irreversible postfeeding stage after 25, 16, 6 and 2 h of starvation, respectively.

Dependence of energy characteristics of ascending swirling air flow on velocity of vertical blowing

Science.gov (United States)

Volkov, R. E.; Obukhov, A. G.; Kutrunov, V. N.

2018-05-01

In the model of a compressible continuous medium, for the complete Navier-Stokes system of equations, an initial boundary problem is proposed that corresponds to the conducted and planned experiments and describes complex three-dimensional flows of a viscous compressible heat-conducting gas in ascending swirling flows that are initiated by a vertical cold blowing. Using parallelization methods, three-dimensional nonstationary flows of a polytropic viscous compressible heat-conducting gas are constructed numerically in different scaled ascending swirling flows under the condition when gravity and Coriolis forces act. With the help of explicit difference schemes and the proposed initial boundary conditions, approximate solutions of the complete system of Navier-Stokes equations are constructed as well as the velocity and energy characteristics of three-dimensional nonstationary gas flows in ascending swirling flows are determined.

Polyurethane Foams for Thermal Insulation Uses Produced from Castor Oil and Crude Glycerol Biopolyols.

Science.gov (United States)

Carriço, Camila S; Fraga, Thaís; Carvalho, Vagner E; Pasa, Vânya M D

2017-07-02

Rigid polyurethane foams were synthesized using a renewable polyol from the simple physical mixture of castor oil and crude glycerol. The effect of the catalyst (DBTDL) content and blowing agents in the foams' properties were evaluated. The use of physical blowing agents (cyclopentane and n-pentane) allowed foams with smaller cells to be obtained in comparison with the foams produced with a chemical blowing agent (water). The increase of the water content caused a decrease in density, thermal conductivity, compressive strength, and Young's modulus, which indicates that the increment of CO₂ production contributes to the formation of larger cells. Higher amounts of catalyst in the foam formulations caused a slight density decrease and a small increase of thermal conductivity, compressive strength, and Young's modulus values. These green foams presented properties that indicate a great potential to be used as thermal insulation: density (23-41 kg·m -3 ), thermal conductivity (0.0128-0.0207 W·m -1 ·K -1 ), compressive strength (45-188 kPa), and Young's modulus (3-28 kPa). These biofoams are also environmentally friendly polymers and can aggregate revenue to the biodiesel industry, contributing to a reduction in fuel prices.

Method for producing small hollow spheres

International Nuclear Information System (INIS)

Hendricks, C.D.

1979-01-01

A method is described for producing small hollow spheres of glass, metal or plastic, wherein the sphere material is mixed with or contains as part of the composition a blowing agent which decomposes at high temperature (T >approx. 600 0 C). As the temperature is quickly raised, the blowing agent decomposes and the resulting gas expands from within, thus forming a hollow sphere of controllable thickness. The thus produced hollow spheres (20 to 10 3 μm) have a variety of application, and are particularly useful in the fabrication of targets for laser implosion such as neutron sources, laser fusion physics studies, and laser initiated fusion power plants

Morphology and Developmental Rate of the Blow Fly, Hemipyrellia ligurriens (Diptera: Calliphoridae: Forensic Entomology Applications

Directory of Open Access Journals (Sweden)

Nophawan Bunchu

2012-01-01

Full Text Available Hemipyrellia ligurriens (Diptera: Calliphoridae is a forensically important blow fly species presented in many countries. In this study, we determined the morphology of all stages and the developmental rate of H. ligurriens reared under natural ambient conditions in Phitsanulok province, northern Thailand. Morphological features of all stages based on observing under a light microscope were described and demonstrated in order to use for identification purpose. Moreover, development time in each stage was given. The developmental time of H. ligurriens to complete metamorphosis; from egg, larva, pupa to adult, took 270.71 h for 1 cycle of development. The results from this study may be useful not only for application in forensic investigation, but also for study in its biology in the future.

Forensically Important Blow Flies Chrysomya pinguis, C. villeneuvi, and Lucilia porphyrina (Diptera: Calliphoridae) in a Case of Human Remains in Thailand

Science.gov (United States)

Monum, Tawatchai; Sukontason, Kabkaew L.; Sribanditmongkol, Pongruk; Sukontason, Kom; Samerjai, Chutharat; Limsopatham, Kwankamol; Suwannayod, Suttida; Klong-klaew, Tunwadee; Wannasan, Anchalee

2017-01-01

This is the first study to report Chrysomya pinguis (Walker) and Lucilia porphyrina (Walker) (Diptera: Calliphoridae) as forensically important blow fly species from human cadavers in Thailand, in addition to Chrysomya villeneuvi (Patton) already known in Thailand. In 2016, a fully decomposed body of an unknown adult male was discovered in a high mountainous forest during winter in Chiang Mai province. The remains were infested heavily with thousands of blow fly larvae feeding simultaneously on them. Morphological identification of adults reared from the larvae, and molecular analysis based on sequencing of 1,247 bp partial mitochondrial cytochrome c oxidase subunit 1 gene (CO1) of the larvae and puparia, confirmed the above mentioned 3 species. The approving forensic fly evidence by molecular approach was described for the first time in Thailand. Moreover, neighbor-joining phylogenetic analysis of the CO1 was performed to compare the relatedness of the species, thereby affirming the accuracy of identification. As species of entomofauna varies among cases in different geographic and climatic circumstances, C. pinguis and L. porphyrina were added to the list of Thai forensic entomology caseworks, including colonizers of human remains in open, high mountainous areas during winter. Further research should focus on these 3 species, for which no developmental data are currently available. PMID:28285509

Cool-weather activity of the forensically important hairy maggot blow fly Chrysomya rufifacies (Macquart) (Diptera: Calliphoridae) on carrion in Upstate South Carolina, United States.

Science.gov (United States)

Cammack, Jonathan A; Nelder, Mark P

2010-02-25

The hairy maggot blow fly Chrysomya rufifacies (Macquart) (Diptera: Calliphoridae) has expanded its range in the United States since its introduction into Texas (ca. 1980) and has been collected in 15 states. We investigated the bionomics of immature and adult C. rufifacies collected from carcasses of a raccoon Procyon lotor (Linnaeus) and white-tailed deer Odocoileus virginianus Zimmerman in Upstate South Carolina during November 2007, and used these insects to estimate the minimum period of insect activity. Puparia of C. rufifacies were collected from deer carrion; 28% were parasitized by Nasonia vitripennis (Walker) (Hymenoptera: Pteromalidae). The mean daily ambient temperature during this study was 11.4+/-1.02 degrees C, representing the lowest recorded mean temperature for adult activity of C. rufifacies; adults of C. rufifacies were observed flying among the carcasses at 9.0 degrees C. Although C. rufifacies is considered a warm-weather blow fly, researchers should be aware of its activity at suboptimal conditions, behavior that might aid its expansion into more northern areas. 2009 Elsevier Ireland Ltd. All rights reserved.

Changes in Blow-Off Velocity Observed in Two Explosives at the Threshold for Sustained Ignition Using the Modified Gap Test

Science.gov (United States)

Lee, R. J.; Forbes, J. W.; Tasker, D. G.; Orme, R. S.

2009-12-01

The Modified Gap Test was used to quantify different levels of partial reaction for various input stresses. This test configuration has been historically useful in highlighting thresholds for first reaction, sustained ignition, and detonation. Two different HMX based compositions were studied; a cast-cured composition with 87% HMX and a pressed composition with 92% HMX. Each explosive was prepared from large industrially produced batches consisting of different unreactive polymeric binder systems. Short samples (50.8 mm in diameter and 12.7 mm thick) were shock loaded using the standard large-scale gap test donor system. Product-cloud blow-off velocities at the opposite end of the sample were measured using a high-speed digital-camera. Velocity versus input pres sure plots provided changes in reactivity that had developed by the 12.7 mm run distance. Results appear consistent for the lower input stresses. In contrast, the results varied widely in a range of input stresses around the transition to detonation in both explosives. These results indicate that both explosives are subject to large variation in blow-off velocity in a range of input stresses near the threshold for prompt detonation. This is explained by localized variations of HMX particle size and density in industrially prepared samples. Approved for public release, Distribution unlimited, IHDIV Log No. 09-108.

Recovery Act. Advanced Building Insulation by the CO₂ Foaming Process

Energy Technology Data Exchange (ETDEWEB)

Yang, Arthur [Industrial Science and Technology Network, Inc., Lancaster, PA (United States)

2013-12-30

In this project, ISTN proposed to develop a new "3rd" generation of insulation technology. The focus was a cost-effective foaming process that could be used to manufacture XPS and other extruded polymer foams using environmentally clean blowing agents, and ultimately achieve higher R-values than existing products while maintaining the same level of cost-efficiency. In the U.S., state-of-the-art products are primarily manufactured by two companies: Dow and Owens Corning. These products (i.e., STYROFOAM and FOAMULAR) have a starting thermal resistance of R-5.0/inch, which declines over the life of the product as the HFC blowing agents essential to high R-value exchange with air in the environment. In the existing technologies, the substitution of CO2 for HFCs as the primary foaming agent results in a much lower starting R-value, as evidenced in CO2-foamed varieties of XPS in Europe with R-4.2/inch insulation value. The major overarching achievement from this project was ISTN's development of a new process that uses CO2 as a clean blowing agent to achieve up to R-5.2/inch at the manufacturing scale, with a production cost on a per unit basis that is less than the cost of Dow and Owens Corning XPS products.

Effects of eucalyptol on house fly (Diptera: Muscidae and blow fly (Diptera: Calliphoridae

Directory of Open Access Journals (Sweden)

Sukontason Kabkaew L.

2004-01-01

Full Text Available The effects of eucalyptol were evaluated against the house fly, Musca domestica L., and blow fly, Chrysomya megacephala (F.. The bioassay of adults, using topical application, indicated that M. domestica males were more susceptible than females, with the LD50 being 118 and 177 mg/fly, respectively. A higher LD50 of C. megacephala was obtained; 197 mg/fly for males and 221 mg/fly for females. Living flies of both species yielded a shorter life span after being treated with eucalyptol. The bioassay of larvae, using the dipping method on the third instar, showed that M. domestica was more susceptible than C. megacephala, with their LC50 being 101 and 642 mg/ml, respectively. The emergence of adults, which had been treated with eucalyptol in larvae, decreased only in M. domestica. Having the volatile property, fumigation or impregnated paper test of eucalyptol or the efficacy of repellence or attractiveness merits further investigations to enhance bio-insecticidal efficacy.

CROSS DIFFUSION AND NONLINEAR DIFFUSION PREVENTING BLOW UP IN THE KELLER–SEGEL MODEL

KAUST Repository

CARRILLO, JOSÉ ANTONIO

2012-12-01

A parabolic-parabolic (Patlak-)Keller-Segel model in up to three space dimensions with nonlinear cell diffusion and an additional nonlinear cross-diffusion term is analyzed. The main feature of this model is that there exists a new entropy functional, yielding gradient estimates for the cell density and chemical concentration. For arbitrarily small cross-diffusion coefficients and for suitable exponents of the nonlinear diffusion terms, the global-in-time existence of weak solutions is proved, thus preventing finite-time blow up of the cell density. The global existence result also holds for linear and fast diffusion of the cell density in a certain parameter range in three dimensions. Furthermore, we show L∞ bounds for the solutions to the parabolic-elliptic system. Sufficient conditions leading to the asymptotic stability of the constant steady state are given for a particular choice of the nonlinear diffusion exponents. Numerical experiments in two and three space dimensions illustrate the theoretical results. © 2012 World Scientific Publishing Company.

Analysis on blow-down transient in water ingress accident of high temperature gas-cooled reactor

International Nuclear Information System (INIS)

Wang, Yan; Zheng, Yanhua; Li, Fu; Shi, Lei

2014-01-01

Water ingress into the primary circuit is generally recognized as one of the severe accidents with potential hazard to the modular high temperature gas-cooled reactor, which will cause a positive reactivity introduction with the increase of steam density in reactor core to enhance neutron slowing-down, also the chemical corrosion of graphite fuel elements and the damage of reflector structure material. The increase of the primary pressure may result in the opening of the safety valves, consequently leading the release of radioactive isotopes and flammable water gas. The research on water ingress transient is significant for the verification of inherent safety characteristics of high temperature gas-cooled reactor. The 200 MWe high temperature gas-cooled reactor (HTR-PM), designed by the Institute of Nuclear and New Energy Technology of Tsinghua University, is exampled to be analyzed in this paper. The design basis accident (DBA) scenarios of double-ended guillotine break of single heat-exchange tube (steam generator heat-exchange tube rupture) are simulated by the thermal-hydraulic analysis code, and some key concerns which are relative to the amount of water into the reactor core during the blow-down transient are analyzed in detail. The results show that both of water mass and steam ratio of the fluid spouting from the broken heat-exchange tube are affected by break location, which will increase obviously with the broken location closing to the outlet of the heat-exchange tube. The double-ended guillotine rupture at the outlet of the heat-exchange will result more steam penetrates into the reactor core in the design basis accident of water ingress. The mass of water ingress will also be affected by the draining system. It is concluded that, with reasonable optimization on design to balance safety and economy, the total mass of water ingress into the primary circuit of reactor could be limited effectively to meet the safety requirements, and the pollution of

Crosslinked polyethylene foams, via eb radiation

International Nuclear Information System (INIS)

Cardoso, E.C.L.; Lugao, A. B.; Andrade e Silva, L. G.

1998-01-01

Polyethylene foams, produced by radio-induced crosslinking, show a smooth and homogeneous surface, when compared to chemical crosslinking method using peroxide as crosslinking agent. This process fosters excellent adhesive and printability properties. Besides that, closed cells, intrinsic to these foams, imparts optimum mechanical, shocks and insulation resistance, indicating these foams to some markets segments as: automotive and transport; buoyancy, flotation and marine; building and insulation; packaging; domestic sports and leisure goods. We were in search of an ideal foam, by adding 5 to 15% of blowing agent in LDPE. A series of preliminary trials defined 203 degree sign C as the right blowing agent decomposition temperature. At a 22.7 kGys/dose ratio, the lowest dose for providing an efficient foam was 30 kGy, for a formulation comprising 10% of azodicarbonamide in LDPE, within a 10 minutes foaming time

Method and apparatus for producing small hollow spheres

International Nuclear Information System (INIS)

Hendricks, C.D.

1979-01-01

A method and apparatus are described for producing small hollow spheres of glass, metal or plastic, wherein the sphere material is mixed with or contains as part of the composition a blowing agent which decomposes at high temperature (T greater than or equal to 600 0 C). As the temperature is quickly raised, the blowing agent decomposes and the resulting gas expands from within, thus forming a hollow sphere of controllable thickness. The thus produced hollow spheres (20 to 10 3 μm) have a variety of application, and are particularly useful in the fabrication of targets for laser implosion such as neutron sources, laser fusion physics studies, and laser initiated fusion power plants

40 CFR 82.17 - Apportionment of baseline production allowances for class II controlled substances.

Science.gov (United States)

2010-07-01

... allowances for class II controlled substances. 82.17 Section 82.17 Protection of Environment ENVIRONMENTAL... Consumption Controls § 82.17 Apportionment of baseline production allowances for class II controlled... 1,759,681 MDA Manufacturing HCFC-22 2,383,835 Solvay Solexis HCFC-142b 6,541,764 [ 74 FR 66446, Dec...

Self-Calibrating, Variable-Flow Pumping System

Science.gov (United States)

Walls, Joe T.

1994-01-01

Pumping system provides accurate, controlled flows of two chemical liquids mixed in spray head and react to form rigid or flexible polyurethane or polyisocyanurate foam. Compatible with currently used polyurethane-based coating materials and gas-bubble-forming agents (called "blowing agents" in industry) and expected to be compatible with materials that used in near future. Handles environmentally acceptable substitutes for chlorofluorocarbon foaming agents.

USB environment measurements based on full-scale static engine ground tests. [Upper Surface Blowing for YC-14

Science.gov (United States)

Sussman, M. B.; Harkonen, D. L.; Reed, J. B.

1976-01-01

Flow turning parameters, static pressures, surface temperatures, surface fluctuating pressures and acceleration levels were measured in the environment of a full-scale upper surface blowing (USB) propulsive-lift test configuration. The test components included a flightworthy CF6-50D engine, nacelle and USB flap assembly utilized in conjunction with ground verification testing of the USAF YC-14 Advanced Medium STOL Transport propulsion system. Results, based on a preliminary analysis of the data, generally show reasonable agreement with predicted levels based on model data. However, additional detailed analysis is required to confirm the preliminary evaluation, to help delineate certain discrepancies with model data and to establish a basis for future flight test comparisons.

75 FR 34017 - Protection of Stratospheric Ozone: Notice 25 for Significant New Alternatives Policy Program

Science.gov (United States)

2010-06-16

... open from 8:30 a.m. to 4:30 p.m., Monday through Friday, excluding legal holidays. The telephone number... substitute listed as unacceptable, except for certain exceptions (e.g., test marketing, research and..., 2010, virgin HCFC-22 and HCFC-142b, and blends containing one or both of these compounds, may only be...

Performance of alternative refrigerants for residential air-conditioning applications

International Nuclear Information System (INIS)

Park, Ki-Jung; Seo, Taebeom; Jung, Dongsoo

2007-01-01

In this study, performances of two pure hydrocarbons and seven mixtures composed of propylene, propane, HFC152a, and dimethylether were measured to substitute for HCFC22 in residential air-conditioners and heat pumps. Thermodynamic cycle analysis was carried out to determine the optimum compositions before testing and actual tests were performed in a breadboard-type laboratory heat pump/air-conditioner at the evaporation and condensation temperatures of 7 and 45 deg. C, respectively. Test results show that the coefficient of performance of these mixtures is up to 5.7% higher than that of HCFC22. While propane showed a 11.5% reduction in capacity, most of the fluids had a similar capacity to that of HCFC22. For these fluids, compressor-discharge temperatures were reduced by 11-17 deg. C. For all fluids tested, the amount of charge was reduced by up to 55% as compared to HCFC22. Overall, these fluids provide good performances with reasonable energy-savings without any environmental problem and thus can be used as long-term alternatives for residential air-conditioning and heat-pumping applications

Reduced fractal model for quantitative analysis of averaged micromotions in mesoscale: Characterization of blow-like signals

International Nuclear Information System (INIS)

Nigmatullin, Raoul R.; Toboev, Vyacheslav A.; Lino, Paolo; Maione, Guido

2015-01-01

Highlights: •A new approach describes fractal-branched systems with long-range fluctuations. •A reduced fractal model is proposed. •The approach is used to characterize blow-like signals. •The approach is tested on data from different fields. -- Abstract: It has been shown that many micromotions in the mesoscale region are averaged in accordance with their self-similar (geometrical/dynamical) structure. This distinctive feature helps to reduce a wide set of different micromotions describing relaxation/exchange processes to an averaged collective motion, expressed mathematically in a rather general form. This reduction opens new perspectives in description of different blow-like signals (BLS) in many complex systems. The main characteristic of these signals is a finite duration also when the generalized reduced function is used for their quantitative fitting. As an example, we describe quantitatively available signals that are generated by bronchial asthmatic people, songs by queen bees, and car engine valves operating in the idling regime. We develop a special treatment procedure based on the eigen-coordinates (ECs) method that allows to justify the generalized reduced fractal model (RFM) for description of BLS that can propagate in different complex systems. The obtained describing function is based on the self-similar properties of the different considered micromotions. This kind of cooperative model is proposed here for the first time. In spite of the fact that the nature of the dynamic processes that take place in fractal structure on a mesoscale level is not well understood, the parameters of the RFM fitting function can be used for construction of calibration curves, affected by various external/random factors. Then, the calculated set of the fitting parameters of these calibration curves can characterize BLS of different complex systems affected by those factors. Though the method to construct and analyze the calibration curves goes beyond the scope

Integral blow moulding for cycle time reduction of CFR-TP aluminium contour joint processing

Science.gov (United States)

Barfuss, Daniel; Würfel, Veit; Grützner, Raik; Gude, Maik; Müller, Roland

2018-05-01

Integral blow moulding (IBM) as a joining technology of carbon fibre reinforced thermoplastic (CFR-TP) hollow profiles with metallic load introduction elements enables significant cycle time reduction by shortening of the process chain. As the composite part is joined to the metallic part during its consolidation process subsequent joining steps are omitted. In combination with a multi-scale structured load introduction element its form closure function enables to pass very high loads and is capable to achieve high degrees of material utilization. This paper first shows the process set-up utilizing thermoplastic tape braided preforms and two-staged press and internal hydro formed load introduction elements. Second focuses on heating technologies and process optimization. Aiming at cycle time reduction convection and induction heating in regard to the resulting product quality is inspected by photo micrographs and computer tomographic scans. Concluding remarks give final recommendations for the process design in regard to the structural design.

Environmental Compliance Assessment Management Program (ECAMP) - U.S. Fish and Wildlife Service (FWS)

Science.gov (United States)

1994-06-01

for wetlands protection. Whistle Blower Hotline, USEPA 800-424-4000 Allows for reporting of fraud,. waste, and abuse in USEPA programs. iv Table 1...x U172 924-16-3 nitroso- 1 -Chloro-1,1 - difluoroethane x 75-68-3 (HCFC-142(b) 1 -Chloro-1,1,2,2-tetrafluoroet- x 354-25-6 hane (HCFC-124a) 1

Theoretical study of heat pump system using CO2/dimethylether as refrigerant

Directory of Open Access Journals (Sweden)

Fan Xiao-Wei

2013-01-01

Full Text Available Nowadays, HCFC22 is widely used in heat pump systems in China, which should be phased out in the future. Thus, eco-friendly mixture CO2/dimethylether is proposed to replace HCFC22. Compared with pure CO2 and pure dimethylether, the mixture can reduce the heat rejection pressure, and suppress the flammability and explosivity of pure dimethylether. According to the Chinese National Standards on heat pump water heater and space heating system, performances of the subcritical heat pump system are discussed and compared with those of the HCFC22 system. It can be concluded that CO2 /dimethylether mixture works efficiently as a refrigerant for heat pumps with a large heat-sink temperature rise. When mass fraction of dimethylether is increased, the heat rejection pressure is reduced. Under the nominal working condition, there is an optimal mixture mass fraction of 28/72 of CO2/dimethylether for water heater application under conventional condensation pressure, 3/97 for space heating application. For water heater application, both the heating coefficient of performance and volumetric heating capacity increase by 17.90% and 2.74%, respectively, compared with those of HCFC22 systems. For space heating application, the heating coefficient of performance increases by 8.44% while volumetric heating capacity decreases by 34.76%, compared with those of HCFC22 systems. As the superheat degree increases, both the heating coefficient of performance and volumetric heating capacity tend to decrease.

Debris transport evaluation during the blow-down phase of a LOCA using computational fluid dynamics

International Nuclear Information System (INIS)

Park, Jong Pil; Jeong, Ji Hwan; Kim, Won Tae; Kim, Man Woong; Park, Ju Yeop

2011-01-01

Highlights: → We conducted CFD simulation on the spreading of the coolant in the containment after a break of the hot leg. It is used to estimate the dispersion of the debris within the containment. → It was assumed that the small and fine debris is transported by the discharge flow so that a fraction of the small and fine debris transport can be estimated based on the amount of water. → The break flow was assumed to be a homogeneous two-phase mixture without phase separation. Isenthalpic expansion of the break flow was used to specify the inlet boundary condition of the break flow. → The fraction of the small and fine debris transported to the upper part is 73%; this value is close to the value calculated using 1D lumped-parameter codes by the USNRC and the KINS, respectively, while 48% more than the value shown in the NEI 04-07. - Abstract: The performance of the emergency recirculation water sump under the influence of debris accumulation following a loss-of-coolant accident (LOCA) has long been of safety concern. Debris generation and transport during a LOCA are significantly influenced by the characteristics of the ejected coolant flow. One-dimensional analyses previously have been attempted to evaluate the debris transport during the blow-down phase but the transport evaluation still has large uncertainties. In this work, a computational fluid dynamics (CFD) analysis was utilized to evaluate small and fine debris transport during the blow-down phase of a pressurized water reactor, OPR1000. The coolant ejected from the ruptured hot-leg was assumed to expand in an isenthalpic process. The transport of small and fine debris was assumed to be dominated by water-borne transport, and the transport fractions for the upper and lower parts of the containment were quantified based on the CFD analysis. It was estimated that 73% of small and fine debris is transported to the upper part of the containment. This value is close to the values estimated by nuclear

Blowing dust and highway safety in the southwestern United States: Characteristics of dust emission "hotspots" and management implications.

Science.gov (United States)

Li, Junran; Kandakji, Tarek; Lee, Jeffrey A; Tatarko, John; Blackwell, John; Gill, Thomas E; Collins, Joe D

2018-04-15

Despite the widespread media attention of chain-reaction traffic incidents and property damage caused by windblown dust in the U.S. and elsewhere in the world, very few studies have provided in-depth analysis on this issue. Remote sensing and field observations reveal that wind erosion in the southwestern U.S. typically occurs in localized source areas, characterized as "hotspots", while most of the landscape is not eroding. In this study, we identified the spatial and temporal distribution patterns of hotspots that may contribute dust blowing onto highways in the southwestern U.S. We further classified the hotspots for the potential of blowing dust production based upon field observations and wind erosion modeling. Results of land use and land cover show that shrubland, grassland, and cropland accounted for 42%, 31%, and 21% of the overall study area, respectively. However, of the 620 total hotspots identified, 164 (26%), 141 (22%), and 234 (38%) are located on shrubland, grassland, and cropland, respectively. Barren land represented 0.9% of the land area but 8% of the dust hotspots. While a majority of these hotspots are located close to highways, we focused on 55 of them, which are located hotspot sites are dominated by sand and silt particles with threshold shear velocities ranging from 0.17-0.78m s -1 , largely depending on the land use of the hotspot sites. Dust emission modeling showed that 13 hotspot sites could produce annual emissions >3.79kg m -2 , yielding highly hazardous dust emissions to ground transportation with visibility hotspots are critical information for highway authorities to make informed and timely management decisions when wind events strike. Copyright © 2017 Elsevier B.V. All rights reserved.

Morphology of immature stages of blow fly, Lucilia sinensis Aubertin (Diptera: Calliphoridae), a potential species of forensic importance.

Science.gov (United States)

Sanit, Sangob; Sukontason, Kom; Kurahashi, Hiromu; Tomberlin, Jeffery K; Wannasan, Anchalee; Kraisittipanit, Rungroj; Sukontason, Kabkaew L

2017-12-01

Lucilia sinensis Aubertin (Diptera: Calliphoridae) is a blow fly species of potential forensic importance since adults are attracted to, and colonize, decomposing vertebrate remains. Blow fly larvae associated with human corpses can be useful evidence in forensic investigations; however, their use is dependent in most cases on proper species identification and availability of developmental data. For identification, morphological information on each life stage is traditionally used. We used scanning electron microscopy (SEM) to examine the ultrastructure of eggs, all instars, and puparia, of L. sinensis. The important characteristics used to differentiate L. sinensis from other species are provided. Distinctive features of the eggs are the slight widening median area extending almost the entire length. The last abdominal segment of the first instar bears elongated outer ventral tubercles along the rim of the last abdominal segment. These tubercles, as well as the well developed median and outer dorsal tubercles, are more prominent in the second and third instars. The surface integument of the tubercles is equipped with circular rows of microtrichia. Pairs of inner dorsal tubercle are absent. Each anterior spiracle is comprised of 9-12 papillae arrange in a single row in the second and third instars. As for the third instar, the dorsal spines between the first and second thoracic segments are delicate, narrow, small, and close together (as row or set). The peristigmatic tufts adjacent to the posterior spiracle of the third instar are moderately branches of short, fine hairs, but minute in puparia. In conclusion, the prominent outer ventral tubercle in all instars and puparia is a new diagnostic feature of L. sinensis and helpful in differentiating it from other Lucilia species that are forensically important. The description of immature L. sinensis in this study will be useful for forensic entomologists in countries where this species exists. Copyright © 2017

BLOW-3A. A theoretical model to describe transient two-phase flow conditions in LMFBR coolant channels

International Nuclear Information System (INIS)

Bottoni, M.; Struwe, D.

1982-12-01

The computer programme BLOW-3A describes sodium boiling phenomena in subassemblies of fast breeder reactors as well as in in-pile or out-of-pile experiments simulating different failure conditions. This report presents a complete documentation of the code from three main viewpoints: the theoretical foundations of the programme are first described with particular reference to the most recent developments; the structure of the programme is then explained in all details necessary for the user to get a rapid acquaintance with it; eventually several examples of the programme validation are discussed thus enabling the reader to acquire a full picture of the possible applications of the code and at the same time to know its validity range. (orig.) [de

Poly(L-lactic acid) and polyurethane nanofibers fabricated by solution blow spinning as potential substrates for cardiac cell culture

Energy Technology Data Exchange (ETDEWEB)

Tomecka, Ewelina, E-mail: etomecka@ch.pw.edu.pl [Department of Microbioanalytics, Institute of Biotechnology, Faculty of Chemistry, Warsaw University of Technology, Noakowskiego 3, 00-664 Warsaw (Poland); Wojasinski, Michal [Department of Biotechnology and Bioprocess Engineering, Faculty of Chemical and Process Engineering, Warsaw University of Technology, Waryńskiego 1, 00-645 Warsaw (Poland); Jastrzebska, Elzbieta; Chudy, Michal [Department of Microbioanalytics, Institute of Biotechnology, Faculty of Chemistry, Warsaw University of Technology, Noakowskiego 3, 00-664 Warsaw (Poland); Ciach, Tomasz [Department of Biotechnology and Bioprocess Engineering, Faculty of Chemical and Process Engineering, Warsaw University of Technology, Waryńskiego 1, 00-645 Warsaw (Poland); Brzozka, Zbigniew [Department of Microbioanalytics, Institute of Biotechnology, Faculty of Chemistry, Warsaw University of Technology, Noakowskiego 3, 00-664 Warsaw (Poland)

2017-06-01

This paper presents a comparison and evaluation of cardiac cell proliferation on poly(L-lactic acid) (PLLA) and polyurethane (PU) nanofibrous mats fabricated by solution blow spinning (SBS). Three different cardiac cell lines: rat cardiomyoblasts (H9C2 line), human (HCM) and rat cardiomyocytes (RCM) were used for experiments. Cell morphology, orientation and proliferation were investigated on non-modified and protein-modified (fibronectin, collagen, gelatin, laminin, poly-L-lysine) surfaces of both types of nanofibers. Obtained results of cell culture on nanofibers surfaces were compared to the results of cell culture on polystyrene (PS) surfaces modified in the same way. The results indicated that in most cases polymeric nanofibers (PLLA and PU) are better substrates for cardiac cell culture than PS surfaces. All types of investigated cells, cultured on nanofibers (PLLA and PU), had more elongated shape than cells cultured on PS surfaces. Moreover, cells were arranged in parallel to each other, according to fibers orientation. Additionally, it was shown that the protein modifications of investigated surfaces influenced on cell proliferation. Therefore, we suggest that the cardiac cell culture on nanofibrous mats fabricated by SBS could be more advanced experimental in vitro model for studies on the effect of various cardiac drugs than traditional culture on PS surface. - Highlights: • Solution blow spinning was used for PLLA and PU nanofibers fabrication. • Three cardiac cell lines differing in age and origin were used for experiments. • The protein modifications of investigated surfaces influenced on cell proliferation. • Nanofibers are better substrates for cardiac cell culture than PS surface. • Nanofibers enable cultivating cardiac cells under conditions similar to in vivo.

Poly(L-lactic acid) and polyurethane nanofibers fabricated by solution blow spinning as potential substrates for cardiac cell culture

International Nuclear Information System (INIS)

Tomecka, Ewelina; Wojasinski, Michal; Jastrzebska, Elzbieta; Chudy, Michal; Ciach, Tomasz; Brzozka, Zbigniew

2017-01-01

This paper presents a comparison and evaluation of cardiac cell proliferation on poly(L-lactic acid) (PLLA) and polyurethane (PU) nanofibrous mats fabricated by solution blow spinning (SBS). Three different cardiac cell lines: rat cardiomyoblasts (H9C2 line), human (HCM) and rat cardiomyocytes (RCM) were used for experiments. Cell morphology, orientation and proliferation were investigated on non-modified and protein-modified (fibronectin, collagen, gelatin, laminin, poly-L-lysine) surfaces of both types of nanofibers. Obtained results of cell culture on nanofibers surfaces were compared to the results of cell culture on polystyrene (PS) surfaces modified in the same way. The results indicated that in most cases polymeric nanofibers (PLLA and PU) are better substrates for cardiac cell culture than PS surfaces. All types of investigated cells, cultured on nanofibers (PLLA and PU), had more elongated shape than cells cultured on PS surfaces. Moreover, cells were arranged in parallel to each other, according to fibers orientation. Additionally, it was shown that the protein modifications of investigated surfaces influenced on cell proliferation. Therefore, we suggest that the cardiac cell culture on nanofibrous mats fabricated by SBS could be more advanced experimental in vitro model for studies on the effect of various cardiac drugs than traditional culture on PS surface. - Highlights: • Solution blow spinning was used for PLLA and PU nanofibers fabrication. • Three cardiac cell lines differing in age and origin were used for experiments. • The protein modifications of investigated surfaces influenced on cell proliferation. • Nanofibers are better substrates for cardiac cell culture than PS surface. • Nanofibers enable cultivating cardiac cells under conditions similar to in vivo.

Injection of new psychoactive substance snow blow associated with recently acquired HIV infections among homeless people who inject drugs in Dublin, Ireland, 2015.

LENUS (Irish Health Repository)

Giese, Coralie

2015-10-08

In February 2015, an outbreak of recently acquired HIV infections among people who inject drugs (PWID) was identified in Dublin, following similar outbreaks in Greece and Romania in 2011. We compared drug and risk behaviours among 15 HIV cases and 39 controls. Injecting a synthetic cathinone, snow blow, was associated with recent HIV infection (AOR: 49; p = 0.003). Prevention and control efforts are underway among PWID in Dublin, but may also be needed elsewhere in Europe.

Application of advanced coatings to narrow neck press and blow plungers in the glass container industry

Energy Technology Data Exchange (ETDEWEB)

Penlington, R. [Northumbria Univ., Newcastle upon Tyne (United Kingdom). Dept. of Mech. Eng. and Manufacturing Syst.; Sarwar, M. [Northumbria Univ., Newcastle upon Tyne (United Kingdom). Dept. of Mech. Eng. and Manufacturing Syst.; Lewis, D.B. [Sheffield Hallam Univ. (United Kingdom)

1995-11-01

Wear and failure modes exhibited by narrow neck press and blow (NNPB) plungers in the glass container industry have been related to inappropriate material selection. Problems exist with substrate and coating materials which lead to machine down time, process instability and poor product quality. Previous attempts to improve the service life of NNPB plungers have not examined the process operating characteristics and demanding nature of the application. New substrate and coating materials have been utilized and an assessment of their suitability for this application examined. Initial results from plant trials with modified plungers suggest that improvements in operational performance are achievable. This application, and other components of the mould tooling set, may benefit from improvements which may increase tool life and reduce the problems which result from the application of lubricant dopes to glass contact surfaces. (orig.)

Plutonium, americium, and uranium in blow-sand mounds of safety-shot sites at the Nevada Test Site and the Tonopah Test Range

International Nuclear Information System (INIS)

Essington, E.H.; Gilbert, R.O.; Wireman, D.L.; Brady, D.N.; Fowler, E.B.

1977-01-01

Blow-sand mounds or miniature sand dunes and mounds created by burrowing activities of animals were investigated by the Nevada Applied Ecology Group (NAEG) to determine the influence of mounds on plutonium, americium, and uranium distributions and inventories in areas of the Nevada Test Site and Tonopah Test Range. Those radioactive elements were added to the environment as a result of safety experiments of nuclear devices. Two studies were conducted. The first was to estimate the vertical distribution of americium in the blow-sand mounds and in the desert pavement surrounding the mounds. The second was to estimate the amount or concentration of the radioactive materials accumulated in the mound relative to the desert pavement. Five mound types were identified in which plutonium, americium, and uranium concentrations were measured: grass, shrub, complex, animal, and diffuse. The mount top (that portion above the surrounding land surface datum), the mound bottom (that portion below the mound to a depth of 5 cm below the surrounding land surface datum), and soil from the immediate area surrounding the mound were compared separately to determine if the radioactive elements had concentrated in the mounds. Results of the studies indicate that the mounds exhibit higher concentrations of plutonium, americium, and uranium than the immediate surrounding soil. The type of mound does not appear to have influenced the amount of the radioactive material found in the mound except for the animal mounds where the burrowing activities appear to have obliterated distribution patterns

Comparison of Absorbable Mesh Plate versus Titanium-Dynamic Mesh Plate in Reconstruction of Blow-Out Fracture: An Analysis of Long-Term Outcomes

Directory of Open Access Journals (Sweden)

Woon Il Baek

2014-07-01

Full Text Available Background A blow-out fracture is one of the most common facial injuries in midface trauma. Orbital wall reconstruction is extremely important because it can cause various functional and aesthetic sequelae. Although many materials are available, there are no uniformly accepted guidelines regarding material selection for orbital wall reconstruction. Methods From January 2007 to August 2012, a total of 78 patients with blow-out fractures were analyzed. 36 patients received absorbable mesh plates, and 42 patients received titanium-dynamic mesh plates. Both groups were retrospectively evaluated for therapeutic efficacy and safety according to the incidence of three different complications: enophthalmos, extraocular movement impairment, and diplopia. Results For all groups (inferior wall fracture group, medial wall fractrue group, and combined inferomedial wall fracture group, there were improvements in the incidence of each complication regardless of implant types. Moreover, a significant improvement of enophthalmos occurred for both types of implants in group 1 (inferior wall fracture group. However, we found no statistically significant differences of efficacy or complication rate in every groups between both implant types. Conclusions Both types of implants showed good results without significant differences in long-term follow up, even though we expected the higher recurrent enophthalmos rate in patients with absorbable plate. In conclusion, both types seem to be equally effective and safe for orbital wall reconstruction. In particular, both implant types significantly improve the incidence of enophthalmos in cases of inferior orbital wall fractures.

Study of process parameters on two phase flow agitated by top blowing lance injection into a bath

Energy Technology Data Exchange (ETDEWEB)

Xia Jiliang; Ahokainen, T.; Holappa, L.

1998-12-31

Numerical investigation has been carried out for two phase flow in a bath agitated by top blowing lance injection. Eulerian two phase flow model is used. Lance immersion depth, injection gas flow rate, nozzle diameter, and bubble size have been systematically changed to examine their influence on the flow characteristics in the bath. It is found that there appear three typical flow patterns: one-vortex, two-vortex, and three-vortex type, with changing the injection gas flow rate or/and the nozzle diameter at moderate lance immersion depth. Predicted velocities are in a good agreement with Iguchi et al.`s experimental data and the main findings are also consistent with the measurements and observations of Chatterjee and Hsiao and Lehner. (orig.) 24 refs. Computational Fluid Dynamics Technology Programme

Blow-off characteristics of turbulent premixed flames in curved-wall Jet Burner

KAUST Repository

Mansour, Morkous S.

2015-08-02

This study concerns the flame dynamics of a curved-wall jet (CWJ) stabilized turbulent premixed flame as it approaches blow-off conditions. Time resolved OH planar laser-induced fluorescence (PLIF) delineated reaction zone contours and simultaneously stereoscopic particle image velocimetry (SPIV) quantified the turbulent flow field features. Ethylene/air flames were stabilized in CWJ burner to determine the sequence of events leading to blowoff. For stably burning flames far from blowoff, flames are characterized with a recirculation zone (RZ) upstream for flame stabilization followed by an intense turbulent interaction jet (IJ) and merged-jet regions downstream; the flame front counterparts the shear layer vortices. Near blowoff, as the velocity of reactants increases, high local stretch rates exceed the extinction stretch rates instantaneously resulting in localized flame extinction along the IJ region. As Reynolds number (Re) increases, flames become shorter and are entrained by larger amounts of cold reactants. The increased strain rates together with heat loss effects result in further fragmentation of the flame, eventually leading to the complete quenching of the flame. This is explained in terms of local turbulent Karlovitz stretch factor (K) and principal flow strain rates associated with C contours. Hydrogen addition and increasing the RZ size lessen the tendency of flames to be locally extinguished.

MIXING LOSSES INVESTIGATION DOWNSTREAM OF TURBINE BLADE CASCADE WITH COOLANT FLOW BLOWING

Directory of Open Access Journals (Sweden)

ASSIM HAMEED YOUSIF

2011-04-01

Full Text Available A major cause of noise and vibration characteristics of turbomachinery has caused by wakes. The characteristics of the wake, the wake decay, the path that it follows, and the mechanisms of mixing losses generated due to the mixing of blade trailing edge cold jet issued into the hot cross flow are important to find adequate solution to the problem. At the present work the wake characteristic was observed by introducing experimental work inside a cascade test rig to investigate the wake domain downstream of blade cascade with the aid of five-hole probe. The case studies were done with cold jets blowing ratios 1.58, 1.667 and 1.935 with jet stream wise angle and jet lateral injection angle 37.5° and 35 º respectively. The measurement showed that there is a certain harmonization in the region of high reverse pressure loss coefficient which reflects the concentration of wake region. Also it was observed three distinct wake regions located in the centre of the passage vortex region. The wake characteristics measurements of the movement path, the growth of wake width, and the physical awareness of the wake propagating may help to explain the mechanisms of mixing losses.

Study polymeric membranes PVDF/TiO2 photocatalytic applications with synthesized by solution blow spinning

International Nuclear Information System (INIS)

Gimenes, T.C.; Pereira, E.A.; Montanhera, M.A.; Paula, F.R. de; Spada, E.R.

2016-01-01

In this study we obtained nanofibers titanium dioxide (TiO2) incorporated into the poly (vinylidene fluoride) - PVDF in different concentrations, using a new technique denominated Solution Blow Spinning. This technique has the merits of simplicity, low cost and high efficiency in the production of nanofibers, compared with the technique of Electrospinning, using pressurized gas instead of high voltage, is not limited to the dielectric constant of the material and provides a processing period of at least 100 times faster. The obtained nanofibers exhibit little account and a very smooth morphology, with diameters ranging from 400 to 700 nm and with presence of crystalline anatase phase. The tests showed photocatalytic degradation of Rhodamine B dye, being more degradation shown by the PVDF nanofibers containing 0,7 g of TiO 2 , approximately 75 % of degraded dye. However nanofibers obtained the PVDF/TiO2 applications of this material are numerous, as filters, conductive nanofibers, photocatalysis and sensors. (author)

Three-dimensional strutted graphene grown by substrate-free sugar blowing for high-power-density supercapacitors

Science.gov (United States)

Wang, Xuebin; Zhang, Yuanjian; Zhi, Chunyi; Wang, Xi; Tang, Daiming; Xu, Yibin; Weng, Qunhong; Jiang, Xiangfen; Mitome, Masanori; Golberg, Dmitri; Bando, Yoshio

2013-12-01

Three-dimensional graphene architectures in the macroworld can in principle maintain all the extraordinary nanoscale properties of individual graphene flakes. However, current 3D graphene products suffer from poor electrical conductivity, low surface area and insufficient mechanical strength/elasticity; the interconnected self-supported reproducible 3D graphenes remain unavailable. Here we report a sugar-blowing approach based on a polymeric predecessor to synthesize a 3D graphene bubble network. The bubble network consists of mono- or few-layered graphitic membranes that are tightly glued, rigidly fixed and spatially scaffolded by micrometre-scale graphitic struts. Such a topological configuration provides intimate structural interconnectivities, freeway for electron/phonon transports, huge accessible surface area, as well as robust mechanical properties. The graphene network thus overcomes the drawbacks of presently available 3D graphene products and opens up a wide horizon for diverse practical usages, for example, high-power high-energy electrochemical capacitors, as highlighted in this work.

Three-dimensional strutted graphene grown by substrate-free sugar blowing for high-power-density supercapacitors

Science.gov (United States)

Wang, Xuebin; Zhang, Yuanjian; Zhi, Chunyi; Wang, Xi; Tang, Daiming; Xu, Yibin; Weng, Qunhong; Jiang, Xiangfen; Mitome, Masanori; Golberg, Dmitri; Bando, Yoshio

2013-01-01

Three-dimensional graphene architectures in the macroworld can in principle maintain all the extraordinary nanoscale properties of individual graphene flakes. However, current 3D graphene products suffer from poor electrical conductivity, low surface area and insufficient mechanical strength/elasticity; the interconnected self-supported reproducible 3D graphenes remain unavailable. Here we report a sugar-blowing approach based on a polymeric predecessor to synthesize a 3D graphene bubble network. The bubble network consists of mono- or few-layered graphitic membranes that are tightly glued, rigidly fixed and spatially scaffolded by micrometre-scale graphitic struts. Such a topological configuration provides intimate structural interconnectivities, freeway for electron/phonon transports, huge accessible surface area, as well as robust mechanical properties. The graphene network thus overcomes the drawbacks of presently available 3D graphene products and opens up a wide horizon for diverse practical usages, for example, high-power high-energy electrochemical capacitors, as highlighted in this work. PMID:24336225

Fabrication of three-dimensional micro-nanofiber structures by a novel solution blow spinning device

Directory of Open Access Journals (Sweden)

Feng Liang

2017-02-01

Full Text Available The fabrication of three-dimensional scaffolds has attracted more attention in tissue engineering. The purpose of this study is to explore a new method for the fabrication of three-dimensional micro-nanofiber structures by combining solution blow spinning and rotating collector. In this study, we successfully fabricated fibers with a minimum diameter of 200 nm and a three-dimensional structure with a maximum porosity of 89.9%. At the same time, the influence of various parameters such as the solvent volatility, the shape of the collector, the feed rate of the solution and the applied gas pressure were studied. It is found that solvent volatility has large effect on the formation of the three-dimensional shape of the structure. The shape of the collector affects the porosity and fiber distribution of the three-dimensional structure. The fiber diameter and fiber uniformity can be controlled by adjusting the solution feed rate and the applied gas pressure. It is feasible to fabricate high-quality three-dimensional micro-nanofiber structure by this new method, which has great potential in tissue engineering.

Hydrochlorofluorocarbon and hydrofluorocarbon emissions in East Asia determined by inverse modeling

Directory of Open Access Journals (Sweden)

A. Stohl

2010-04-01

Full Text Available The emissions of three hydrochlorofluorocarbons, HCFC-22 (CHClF₂, HCFC-141b (CH₃CCl₂F and HCFC-142b (CH₃CClF₂ and three hydrofluorocarbons, HFC-23 (CHF₃, HFC-134a (CH₂FCF₃ and HFC-152a (CH₃CHF₂ from four East Asian countries and the Taiwan region for the year 2008 are determined by inverse modeling. The inverse modeling is based on in-situ measurements of these halocarbons at the Japanese stations Cape Ochi-ishi and Hateruma, the Chinese station Shangdianzi and the South Korean station Gosan. For every station and every 3 h, 20-day backward calculations were made with the Lagrangian particle dispersion model FLEXPART. The model output, the measurement data, bottom-up emission information and corresponding uncertainties were fed into an inversion algorithm to determine the regional emission fluxes. The model captures the observed variation of halocarbon mixing ratios very well for the two Japanese stations but has difficulties explaining the large observed variability at Shangdianzi, which is partly caused by small-scale transport from Beijing that is not adequately captured by the model. Based on HFC-23 measurements, the inversion algorithm could successfully identify the locations of factories known to produce HCFC-22 and emit HFC-23 as an unintentional byproduct. This lends substantial credibility to the inversion method. We report national emissions for China, North Korea, South Korea and Japan, as well as emissions for the Taiwan region. Halocarbon emissions in China are much larger than the emissions in the other countries together and contribute a substantial fraction to the global emissions. Our estimates of Chinese emissions for the year 2008 are 65.3±6.6 kt/yr for HCFC-22 (17% of global emissions extrapolated from Montzka et al., 2009, 12.1±1.6 kt/yr for HCFC-141b (22%, 7.3±0.7 kt/yr for HCFC-142b (17%, 6.2±0.7 kt/yr for HFC

Effect of breathing technique of blowing on the extent of damage to the perineum at the moment of delivery: A randomized clinical trial

Directory of Open Access Journals (Sweden)

Zohre Ahmadi

2017-01-01

Full Text Available Introduction: One of the important tasks in managing labor is the protection of perineum. An important variable affecting this outcome is maternal pushing during the second stage of labor. This study was done to investigate the effect of breathing technique on perineal damage extention in laboring Iranian women. Materials and Methods: This randomized clinical trial was performed on 166 nulliparous pregnant women who had reached full-term pregnancy, had low risk pregnancy, and were candidates for vaginal delivery in two following groups: using breathing techniques (case group and valsalva maneuver (control group. In the control group, pushing was done with holding the breath. In the case group, the women were asked to take 2 deep abdominal breaths at the onset of pain, then take another deep breath, and push 4–5 seconds with the open mouth while controlling exhalation. From the crowning stage onward, the women were directed to control their pushing, and do the blowing technique. Results: According to the results, intact perineum was more observed in the case group (P = 0.002. Posterior tears (Grade 1, 2, and 3 was considerably higher in the control group (P = 0.003. Anterior tears (labias and episiotomy were not significantly different in the two groups. Conclusions: It was concluded that breathing technique of blowing can be a good alternative to Valsalva maneuver in order to reduce perineal damage in laboring women.

Agent Programming Languages and Logics in Agent-Based Simulation

DEFF Research Database (Denmark)

Larsen, John

2018-01-01

and social behavior, and work on verification. Agent-based simulation is an approach for simulation that also uses the notion of agents. Although agent programming languages and logics are much less used in agent-based simulation, there are successful examples with agents designed according to the BDI...

Blow-off device for limiting excess pressure in nuclear power plants, especially in boiling water nuclear power plants

International Nuclear Information System (INIS)

Simon, U.; Werner, K.D.; Hoffmann, D.; Pontani, B.

1979-01-01

In a blow-off device for limiting excess pressure in nuclear power plants, at least one condensation tube disposed so that a lower outflow and thereof is immersed in a volume of water, and an upper inflow end of the condensation tube extends out of the volume of water and is connectible to a source of steam that is to be condensed or a steam-air mixture, the outflow end of the condensation tube, for stabilizing the condensation being provided with an assembly of wall parts forming passageways extending in axial direction for subdividing the steam flow and bubbles produced in the volume of water, the passageways of the assembly of wall parts being stepped in axial direction at both axial ends of the assembly of wall parts

Agents unleashed a public domain look at agent technology

CERN Document Server

Wayner, Peter

1995-01-01

Agents Unleashed: A Public Domain Look at Agent Technology covers details of building a secure agent realm. The book discusses the technology for creating seamlessly integrated networks that allow programs to move from machine to machine without leaving a trail of havoc; as well as the technical details of how an agent will move through the network, prove its identity, and execute its code without endangering the host. The text also describes the organization of the host's work processing an agent; error messages, bad agent expulsion, and errors in XLISP-agents; and the simulators of errors, f

Scanning electron microscopic studies on antenna of Hemipyrellia ligurriens (Wiedemann, 1830) (Diptera: Calliphoridae)-A blow fly species of forensic importance.

Science.gov (United States)

Hore, Garima; Maity, Aniruddha; Naskar, Atanu; Ansar, Waliza; Ghosh, Shyamasree; Saha, Goutam Kumar; Banerjee, Dhriti

2017-08-01

Blow flies (Diptera: Calliphoridae) are one of the foremost organisms amongst forensic insects to colonize corpses shortly after death, thus are of immense importance in the domain of forensic entomology. The blow fly Hemipyrellia ligurriens (Wiedemann, 1830) (Diptera: Calliphoridae) is considered as a forensically important fly species globally and is also known for its medical and veterinary importance. In the present study, we report for the first time scanning electron microscopic studies on the morphology of sensilla of antenna of adult male and female of H. ligurriens is with profound importance in better understanding of the insect morphology from forensic entomological perspective, and also could aid in proper identification of the species from other calliphorid flies. The structural peculiarities observed in the (i) antenna of H. ligurriens with three segments- scape, pedicel and flagellum with dorso-laterally placed arista (ii) densely covered microtrichia and most abundant trichoid sensilla identified on the antenna (iii) observation of only one type of sensilla, chaetic sensilla (ChI) on the scape (iv) two types of chaetic sensilla (ChI and ChII) and styloconic sensilla on the pedicel (v) the flagellum with three types of sensilla- trichoid, basiconic and coeloconic sensilla (vi) Basiconic sensilla with multiporous surfaces with characteristic olfactory function. Moderate sexual dimorphism in the width of the flagellum, the females with wider flagella than the males, bear significance to the fact that they bear more multi-porous sensilla than the males, thus suffice their need to detect oviposition sites. Significant difference was observed in the length and width of coeloconic sensilla between the two sexes, the females showed bigger coeloconic sensilla, suggesting their function in oviposition site detection and successful colonization in corpses. Copyright © 2017 Elsevier B.V. All rights reserved.

Mobile Agent Data Integrity Using Multi-Agent Architecture

National Research Council Canada - National Science Library

McDonald, Jeffrey

2004-01-01

.... Security issues for mobile agents continue to produce research interest, particularly in developing mechanisms that guarantee protection of agent data and agent computations in the presence of malicious hosts...

FY 1998 annual summary report on recent trends of global warming prevention measures with fluorochlorohydrocarbon alternatives; 1998 nendo daitia furon no chikyu ondanka taisaku doko ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Described herein are the recent trends of the ozone layer protection and global warming prevention measures. Latest international information has been collected by attending the 10th Meeting of the Party of Montreal Protocol, and the 17th and 18th Open Ended Working Group. The important decisions made so far are investigation on the novel ozone layer destruction substances, requirement of studying on decommissioning Halon facilities, collection of information of HFC and PFC, and reporting to IPCC. Information regarding regulation trends of HFC, PFC and SF{sub 6} are collected by attending the COP-4 meeting and the preparatory meetings therefor. The report on these 3 substances will be completed in July or so, 1999. The trends of technical development in HCFC alternatives in refrigeration and blowing sectors were investigated. HFC-245fa and HFC-365mfc are introduced. Also introduced is latest information regarding the emission estimation and control measures of HFC in USA and UK, emission control measures of SF{sub 6} in USA and Japan, and techniques for destruction of CFC and the like, which could be the basic techniques for controlling diffusion of HFC. The CFC phase-out programs of China, the biggest ozone layer destruction substance (e.g., CFC) consuming country, are also outlined. (NEDO)

Dead-blow hammer design applied to a calibration target mechanism to dampen excessive rebound

Science.gov (United States)

Lim, Brian Y.

1991-01-01

An existing rotary electromagnetic driver was specified to be used to deploy and restow a blackbody calibration target inside of a spacecraft infrared science instrument. However, this target was much more massive than any other previously inherited design applications. The target experienced unacceptable bounce when reaching its stops. Without any design modification, the momentum generated by the driver caused the target to bounce back to its starting position. Initially, elastomeric dampers were used between the driver and the target. However, this design could not prevent the bounce, and it compromised the positional accuracy of the calibration target. A design that successfully met all the requirements incorporated a sealed pocket 85 percent full of 0.75 mm diameter stainless steel balls in the back of the target to provide the effect of a dead-blow hammer. The energy dissipation resulting from the collision of balls in the pocket successfully dampened the excess momentum generated during the target deployment. The disastrous effects of new requirements on a design with a successful flight history, the modifications that were necessary to make the device work, and the tests performed to verify its functionality are described.

Element Distribution in the Oxygen-Rich Side-Blow Bath Smelting of a Low-Grade Bismuth-Lead Concentrate

Science.gov (United States)

Yang, Tianzu; Xiao, Hui; Chen, Lin; Chen, Wei; Liu, Weifeng; Zhang, Duchao

2018-03-01

Oxygen-rich side-blow bath smelting (OSBS) technology offers an efficient method for processing complex bismuth-lead concentrates; however, the element distributions in the process remain unclear. This work determined the distributions of elements, i.e., bismuth, lead, silver, copper, arsenic and antimony, in an industrial-scale OSBS process. The feed, oxidized slag and final products were collected from the respective sampling points and analyzed. For the oxidative smelting process, 65% of bismuth and 76% of silver in the concentrate report to the metal alloy, whereas less lead reports to the metal ( 31%) than the oxidized slag ( 44%). Approximately 50% of copper enters the matte, while more than 63% of arsenic and antimony report to the slag. For the reductive smelting process, less than 4.5% of bismuth, lead, silver and copper in the oxidized slag enter the reduced slag, indicating high recoveries of these metal values.

[Alkylating agents].

Science.gov (United States)

Pourquier, Philippe

2011-11-01

With the approval of mechlorethamine by the FDA in 1949 for the treatment of hematologic malignancies, alkylating agents are the oldest class of anticancer agents. Even though their clinical use is far beyond the use of new targeted therapies, they still occupy a major place in specific indications and sometimes represent the unique option for the treatment of refractory diseases. Here, we are reviewing the major classes of alkylating agents and their mechanism of action, with a particular emphasis for the new generations of alkylating agents. As for most of the chemotherapeutic agents used in the clinic, these compounds are derived from natural sources. With a complex but original mechanism of action, they represent new interesting alternatives for the clinicians, especially for tumors that are resistant to conventional DNA damaging agents. We also briefly describe the different strategies that have been or are currently developed to potentiate the use of classical alkylating agents, especially the inhibition of pathways that are involved in the repair of DNA lesions induced by these agents. In this line, the development of PARP inhibitors is a striking example of the recent regain of interest towards the "old" alkylating agents.

Development of test systems for characterizing emissions from spray polyurethane foam insulation (SPFI)

Science.gov (United States)

The relationship between onsite manufacture of spray polyurethane foam insulation (SPFI) and potential exposures to diisocyanates, amines, flame retardants (FRs), blowing agents, aldehydes and other organic compounds that may be emitted from SPFI is not well understood. EPA is de...

SYMBIOTIC STAR BLOWS BUBBLES INTO SPACE

Science.gov (United States)

2002-01-01

A tempestuous relationship between an unlikely pair of stars may have created an oddly shaped, gaseous nebula that resembles an hourglass nestled within an hourglass. Images taken with Earth-based telescopes have shown the larger, hourglass-shaped nebula. But this picture, taken with NASA's Hubble Space Telescope, reveals a small, bright nebula embedded in the center of the larger one (close-up of nebula in inset). Astronomers have dubbed the entire nebula the 'Southern Crab Nebula' (He2-104), because, from ground-based telescopes, it looks like the body and legs of a crab. The nebula is several light-years long. The possible creators of these shapes cannot be seen at all in this Wide Field and Planetary Camera 2 image. It's a pair of aging stars buried in the glow of the tiny, central nebula. One of them is a red giant, a bloated star that is exhausting its nuclear fuel and is shedding its outer layers in a powerful stellar wind. Its companion is a hot, white dwarf, a stellar zombie of a burned-out star. This odd duo of a red giant and a white dwarf is called a symbiotic system. The red giant is also a Mira Variable, a pulsating red giant, that is far away from its partner. It could take as much as 100 years for the two to orbit around each other. Astronomers speculate that the interaction between these two stars may have sparked episodic outbursts of material, creating the gaseous bubbles that form the nebula. They interact by playing a celestial game of 'catch': as the red giant throws off its bulk in a powerful stellar wind, the white dwarf catches some of it. As a result, an accretion disk of material forms around the white dwarf and spirals onto its hot surface. Gas continues to build up on the surface until it sparks an eruption, blowing material into space. This explosive event may have happened twice in the 'Southern Crab.' Astronomers speculate that the hourglass-shaped nebulae represent two separate outbursts that occurred several thousand years apart

Tensile bond strength of hydroxyethyl methacrylate dentin bonding agent on dentin surface at various drying techniques

Directory of Open Access Journals (Sweden)

Kun Ismiyatin

2010-06-01

Full Text Available Background: There are several dentin surface drying techniques to provide a perfect resin penetration on dentin. There are two techniques which will be compared in this study. The first technique was by rubbing dentin surface gently using cotton pellet twice, this technique is called blot dry technique. The second technique is by air blowing dentin surface for one second and continued by rubbing dentin surface gently using moist cotton. Purpose: This experiment was aimed to examine the best dentin surface drying techniques after 37% phosphoric acid etching to obtain the optimum tensile bond strength between hydroxyethyl methacrylate (HEMA and dentin surface. Method: Bovine teeth was prepared flat to obtain the dentin surface and than was etched using 37% phosphoric acid for 15 seconds. After etching the dentin was cleaned using 20 cc plain water and dried with blot dry techniques (group I, or dried with air blow for one second (group II, or dried with air blow for one second, and continued with rubbing gently using moist cotton pellet (group III, and without any drying as control group (group IV. After these drying, the dentin surfaces were applied with resin dentin bonding agent and put into plunger facing the composite mould. The antagonist plunger was filled with composite resin. After 24 hours, therefore bond strength was measured using Autograph. Result: Data obtained was analyzed using One-Way ANOVA with 95% confidence level and continued with LSD test on p≤0.05. The result showed that the highest tensile bond strength was on group I, while the lowest on group IV. Group II and IV, III and IV, II and III did not show signigicant difference (p>0.05. Conclusion: Dentin surface drying techniques through gentle rubbing using cotton pellet twice (blot dry technique gave the greatest tensile bond strength.Latar belakang masalah: Tehnik pengeringan permukaan dentin agar resin dapat penetrasi dengan sempurna adalah dengan cara pengusapan secara

Incorporating BDI Agents into Human-Agent Decision Making Research

Science.gov (United States)

Kamphorst, Bart; van Wissen, Arlette; Dignum, Virginia

Artificial agents, people, institutes and societies all have the ability to make decisions. Decision making as a research area therefore involves a broad spectrum of sciences, ranging from Artificial Intelligence to economics to psychology. The Colored Trails (CT) framework is designed to aid researchers in all fields in examining decision making processes. It is developed both to study interaction between multiple actors (humans or software agents) in a dynamic environment, and to study and model the decision making of these actors. However, agents in the current implementation of CT lack the explanatory power to help understand the reasoning processes involved in decision making. The BDI paradigm that has been proposed in the agent research area to describe rational agents, enables the specification of agents that reason in abstract concepts such as beliefs, goals, plans and events. In this paper, we present CTAPL: an extension to CT that allows BDI software agents that are written in the practical agent programming language 2APL to reason about and interact with a CT environment.

Chemical warfare agents.

Science.gov (United States)

Kuca, Kamil; Pohanka, Miroslav

2010-01-01

Chemical warfare agents are compounds of different chemical structures. Simple molecules such as chlorine as well as complex structures such as ricin belong to this group. Nerve agents, vesicants, incapacitating agents, blood agents, lung-damaging agents, riot-control agents and several toxins are among chemical warfare agents. Although the use of these compounds is strictly prohibited, the possible misuse by terrorist groups is a reality nowadays. Owing to this fact, knowledge of the basic properties of these substances is of a high importance. This chapter briefly introduces the separate groups of chemical warfare agents together with their members and the potential therapy that should be applied in case someone is intoxicated by these agents.

Logics for Intelligent Agents and Multi-Agent Systems

NARCIS (Netherlands)

Meyer, John-Jules Charles

2014-01-01

This chapter presents the history of the application of logic in a quite popular paradigm in contemporary computer science and artificial intelligence, viz. the area of intelligent agents and multi-agent systems. In particular we discuss the logics that have been used to specify single agents, the

Computational modeling and analysis of heavy water losses in boiler blow down with different positions of BBW-V100 at KANUPP

International Nuclear Information System (INIS)

Maqbool, M. U.

2012-01-01

The term blowdown is referred to the boilers and steam generators. Blowing down water from the steam generators maintains the chemistry of the feedwater and helps prevent scaling or sludge formation. In a nuclear power plant, the primary loop contains some activity in the form of tritium content. In boilers, primary and secondary systems interface and due to the pressure difference there is always a chance of mixing of primary and secondary fluids in event of tube leak. This primary fluid i.e., heavy water in our case can be lost through the blowdown lines after mixing with the feedwater. This thesis is a computational work for the determination of heavy water losses through the blowdown lines. (author)

Fast imaging of the laser-blow-off plume driven shock wave: Dependence on the mass and density of the ambient gas

Energy Technology Data Exchange (ETDEWEB)

George, Sony [ISP, Cochin University of Science and Tech., Cochin 682 022 (India); Singh, R.K., E-mail: rajesh@ipr.res.in [Institute for Plasma Research, Gandhinagar 382 428 (India); Nampoori, V.P.N. [ISP, Cochin University of Science and Tech., Cochin 682 022 (India); Kumar, Ajai [Institute for Plasma Research, Gandhinagar 382 428 (India)

2013-01-17

A systemic investigation of expansion dynamics of plasma plume, produced by laser-blow-off of LiF–C thin film has been done with emphasis on the formation of shock wave and their dependence on the pressure and nature of the ambient gas. The present results demonstrate that highly directional plume produces a strong shock wave in comparison to shock produced by the diverging plume. Shock-velocity, strength and its structure are strongly dependent on ambient environment; maximum shock velocity is observed in helium whereas shock strength is highest in argon environment. The role of chemically reactive processes was not observed in the present case as the plume structure is almost similar in argon and oxygen.

Biological Agents

Science.gov (United States)

... E-Tools Safety and Health Topics / Biological Agents Biological Agents This page requires that javascript be enabled ... 202) 693-2300 if additional assistance is required. Biological Agents Menu Overview In Focus: Ebola Frederick A. ...

Phase Behavior of Three PBX Elastomers in High-Pressure Chlorodifluoromethane

Science.gov (United States)

Lee, Byung-Chul

2017-10-01

The phase equilibrium behavior data are presented for three kinds of commercial polymer-bonded explosive (PBX) elastomers in chlorodifluoromethane (HCFC22). Levapren^{{registered }} ethylene- co-vinyl acetate (LP-EVA), HyTemp^{{registered }} alkyl acrylate copolymer (HT-ACM), and Viton^{{registered }} fluoroelastomer (VT-FE) were used as the PBX elastomers. For each elastomer + HCFC22 system, the cloud point (CP) and/or bubble point (BP) pressures were measured while varying the temperature and elastomer composition using a phase equilibrium apparatus fitted with a variable-volume view cell. The elastomers examined in this study indicated a lower critical solution temperature phase behavior in the HCFC22 solvent. LP-EVA showed the CPs at temperatures of 323 K to 343 K and at pressures of 3 MPa to 10 MPa, whereas HT-ACM showed the CPs at conditions between 338 K and 363 K and between 4 MPa and 12 MPa. For the LP-EVA and HT-ACM elastomers, the BP behavior was observed at temperatures below about 323 K. For the VT-FE + HCFC22 system, only the CP behavior was observed at temperatures between 323 K and 353 K and at pressures between 6 MPa and 21 MPa. As the elastomer composition increased, the CP pressure increased, reached a maximum value at a specific elastomer composition, and then remained almost constant.

Blow Flies from Forest Fragments Embedded in Different Land Uses: Implications for Selecting Indicators in Forensic Entomology.

Science.gov (United States)

de Souza, Mirian S; Pepinelli, Mateus; de Almeida, Eduardo C; Ochoa-Quintero, Jose M; Roque, Fabio O

2016-01-01

Given the general expectation that forest loss can alter biodiversity patterns, we hypothesize that blow fly species abundances differ in a gradient of native vegetation cover. This study was conducted in 17 fragments across different landscapes in central Brazil. Different land cover type proportions were used to represent landscape structure. In total, 2334 specimens of nine species of Calliphoridae were collected. We used principal component analysis (PCA) to reduce dimensionality and multicollinearity of the landscape data. The first component explained 70%, and it represented a gradient of forest-pasture land uses. Alien species showed a wide distribution in different fragments with no clear relationship between the abundance values and the scores of PCA axes, whereas native species occurred only in areas with a predominance of forest cover. Our study revealed that certain native species may be sensitive to forest loss at the landscape scale, and they represent a bioindicator in forensic entomology. © 2015 American Academy of Forensic Sciences.

Prediction of turbulent heat transfer with surface blowing using a non-linear algebraic heat flux model

International Nuclear Information System (INIS)

Bataille, F.; Younis, B.A.; Bellettre, J.; Lallemand, A.

2003-01-01

The paper reports on the prediction of the effects of blowing on the evolution of the thermal and velocity fields in a flat-plate turbulent boundary layer developing over a porous surface. Closure of the time-averaged equations governing the transport of momentum and thermal energy is achieved using a complete Reynolds-stress transport model for the turbulent stresses and a non-linear, algebraic and explicit model for the turbulent heat fluxes. The latter model accounts explicitly for the dependence of the turbulent heat fluxes on the gradients of mean velocity. Results are reported for the case of a heated boundary layer which is first developed into equilibrium over a smooth impervious wall before encountering a porous section through which cooler fluid is continuously injected. Comparisons are made with LDA measurements for an injection rate of 1%. The reduction of the wall shear stress with increase in injection rate is obtained in the calculations, and the computed rates of heat transfer between the hot flow and the wall are found to agree well with the published data

Interaction of antimicrobial preservatives with blow-fill-seal packs: correlating sorption with solubility parameters.

Science.gov (United States)

Amin, Aeshna; Dare, Manish; Sangamwar, Abhay; Bansal, Arvind Kumar

2012-01-01

The aim of this work was to study the interaction of four commonly used ophthalmic antimicrobial preservatives [benzyl alcohol (BA), chlorbutol (CBL), benzalkonium chloride (BKC), and chlorhexidine gluconate (CG)] with Blow-Fill-Seal (BFS) packs. Effect of packaging material [low-density polyethylene (LDPE), polypropylene (PP)], humidity (25% RH, 75% RH) and concentration (0.5, 1.0, 2.0 mM BA/CBL in LDPE) was studied. BKC and CG gave negligible loss (<4%) in BFS packs over a period of 3 months. BA and CBL, however, gave marked losses in LDPE (ca. 70-90%) and PP (ca. 7-25%) packs. Humidity did not have any effect on the sorption loss of any preservative. Loss of BA switched from Case II to anomalous behavior with increasing initial concentration. A two-stage sorption behavior was inherent at all concentrations. Loss of CBL followed anomalous behavior with biphasic kinetics of loss. It was concluded that all the four preservatives were appropriate for use in PP BFS packs. However, only BKC and CG were amenable to be used in LDPE BFS packs. Lastly, an empirical expression consisting of the "solubility parameter distance" and "molar volume" of preservatives was developed to correlate the preservative loss in LDPE with the physicochemical properties of the preservatives.

Development of a Gastroretentive Drug Delivery System based on ...

African Journals Online (AJOL)

Erah

Purpose: The aim of this work was to synthesize superporous hydrogels of rosiglitazone using chitosan and to study its swelling behaviour for application as a gastroretentive drug delivery system. Methods: Chitosan superporous hydrogels were synthesized using glyoxal as a crosslinking agent by gas blowing method.

Computational study on decomposition kinetics of CH3CFClO radical

Indian Academy of Sciences (India)

'greenhouse gases'.5–7. ∗ ... widely used CFCs in the industry as a foam blow- ing agent in polyurethane ... order to access the full impact of its potential use, knowledge of .... This is also supported by the free energy change data included in ...

Assessment of the Possibility of Using Reclaimed Materials for Making Cores by the Blowing Method

Directory of Open Access Journals (Sweden)

Dańko R.

2017-03-01

Full Text Available The cumulative results of investigations of the possibility of using the reclaimed materials after the mechanical, thermal or mechanical-thermal reclamation for making cores by means of the blowing method in the alkaline CO2 technology, are presented in the paper. Three kinds of spent sands: with furfuryl resin, bentonite and alkaline phenolic resin, obtained from the foundry, were subjected to three kinds of reclamation: mechanical, thermal and combined mechanical-thermal, applying for this aim adequate experimental devices. The obtained reclaims were assessed with regard to the degree of the matrix liberation from the determined binding material. Reclaims of moulding sands with binders of the form of resin were assessed with regard to ignition loss values and pH reaction, while reclaims of moulding sands with bentonite with regard to the residual clay content and pH value. In all cases the results of the performed sieve analyses were estimated and the average characteristic diameter dl was determined. The reclaimed matrix was applied as a full substitute of the fresh high-silica sand in typical procedures of preparing core sands used for making shaped samples for bending strength investigations, Rgu.

Contrast agents for cardiac angiography: effects of a nonionic agent vs. a standard ionic agent

International Nuclear Information System (INIS)

Bettmann, M.A.; Bourdillon, P.D.; Barry, W.H.; Brush, K.A.; Levin, D.C.

1984-01-01

The effects on cardiac hemodynamics and of a standard contrast agent, sodium methylglucamine diatrizoate [Renografin 76] were compared with the effects of a new nonionic agent (iohexol) in a double-blind study in 51 patietns undergoing coronary angiography and left ventriculography. No significant alteration in measured blood parameters occurred with either contrast agent. Hemodynamic changes occurred with both, but were significantly greater with the standard renografin than with the low-osmolality, nonionic iohexol. After left ventriculography, heart rate increased and peripheral arterial pressure fell with both agents, but less with iohexol. It is concluded that iohexol causes less alteration in cardiac function than does the agent currently most widely used. Nonionic contrast material is likely to improve the safety of coronary angiography, particularly in those patients at greatest risk

Elaboration of the Thermodynamic Model of Refining the Converter Bath when Blowing through Three-Tier Oxygen Lance

Directory of Open Access Journals (Sweden)

Anatoliy G. Chernyatevich

2017-10-01

Full Text Available Background. In modern conditions, the BOP-process is the main method of mass use steel product production. At the same time, due to the shortage of high-quality charge materials, resource and energy-saving technologies are particularly relevant. To optimize the BOP-process under modern conditions, it is promising to use improved oxygen lances for top blowing in comparison with known designs. Objective. An important stage in the development of advanced steel production technologies is obtaining information on the thermodynamic model of blowing a converter bath through a three-tier lance with the elaboration of the regularities of oxidation processes within the reaction zone of a 160-ton industrial converter. Methods. The analysis that was carried out has a theoretical nature and is based on the definition of the influence of temperature and pressure on the regularities of oxidation processes within the reaction zones formed when oxygen jets are introduced into the volume of a metal bath, foamed slag-metallic emulsion and waste gases in the working space of the converter. As a thermodynamic parameter, the Gibbs energy was used to estimate the probability of chemical reactions. The pressure effect on the oxidation processes in the converter bath was evaluated in accordance with the Van’t Hoff formula. Results. The thermodynamic features of oxidation processes in the 160-ton BOF bath using a three-tier lance are presented. Primary reaction zone is characterized by the occurrence of oxidation of manganese, silicon, carbon, and iron by gaseous oxygen. In the secondary reaction zone there are chemical reactions of the oxidation of silicon and carbon dissolved in the metal by oxygen, as well as the reduction of iron oxide by carbon. The presence or absence of a slag phase on the melt surface practically does not affect the occurrence probability of chemical transformations within the boundary of primary and secondary reaction zones. The additional

Estimating the age of the adult stages of the blow flies Lucilia sericata and Calliphora vicina (Diptera: Calliphoridae) by means of the cuticular hydrocarbon n-pentacosane.

Science.gov (United States)

Bernhardt, Victoria; Pogoda, Werner; Verhoff, Marcel A; Toennes, Stefan W; Amendt, Jens

2017-09-01

Age estimation of insects like blow flies plays an important role in forensic entomology and can answer questions in regard to time of death. So far the focus is on the immature stages of these insects, but recently the adult fly became a target of interest. It has been established that the profile of specific cuticular hydrocarbons (CHCs) changes in a consistent pattern as adult insects age; thus, their analysis could be a promising tool for the age estimation of adult insects. We investigated the CHC n-pentacosane (nC25) on the legs of the adult blow flies Lucilia sericata and Calliphora vicina with gas chromatography-mass spectrometry. The flies were kept at room temperature (17°C±2°C) and 12:12 L:D from Day 1 to Day 20 post-emergence. For each of five flies per species, the amount of nC25 on all legs was determined daily. The amounts of nC25 on C. vicina increased linearly (R 2 =0.949). No significant difference between sexes could be detected. While L. sericata showed the same linear increase in general, we found significant (page is constructed from these data. Although the influence of various environmental factors, e.g., fluctuating temperatures, still needs to be tested, nC25 seems to be a promising tool for the age estimation of adult flies. Copyright © 2017 The Chartered Society of Forensic Sciences. Published by Elsevier B.V. All rights reserved.

A Composite Agent Architecture for Multi-Agent Simulations

OpenAIRE

VanPutte, Michael; Osborn, Brian; Hiles, John

2002-01-01

CGF Computer Generated Forces and Behavioral Representation The MOVES Institute’s Computer-Generated Autonomy Group has focused on a research goal of modeling complex and adaptive behavior while at the same time making the behavior easier to create and control. This research has led to several techniques for agent construction, that includes a social and organization relationship management engine, a composite agent architecture, an agent goal apparatus, a structure for capturi...

TACtic- A Multi Behavioral Agent for Trading Agent Competition

Science.gov (United States)

Khosravi, Hassan; Shiri, Mohammad E.; Khosravi, Hamid; Iranmanesh, Ehsan; Davoodi, Alireza

Software agents are increasingly being used to represent humans in online auctions. Such agents have the advantages of being able to systematically monitor a wide variety of auctions and then make rapid decisions about what bids to place in what auctions. They can do this continuously and repetitively without losing concentration. To provide a means of evaluating and comparing (benchmarking) research methods in this area the trading agent competition (TAC) was established. This paper describes the design, of TACtic. Our agent uses multi behavioral techniques at the heart of its decision making to make bidding decisions in the face of uncertainty, to make predictions about the likely outcomes of auctions, and to alter the agent's bidding strategy in response to the prevailing market conditions.

Short- and long-term releases of fluorocarbons from disposal of polyurethane foam waste

DEFF Research Database (Denmark)

Kjeldsen, Peter; Scheutz, Charlotte

2003-01-01

Several halocarbons having very high global warming or ozone depletion potentials have been used as a blowing agent (BA) for insulation foam in home appliances, such as refrigerators and freezers. Many appliances are shredded after the end of their useful life. Release experiments carried out in ...

Emission of volatiles from spray polyurethane foam (SPF) insulated crawl spaces

NARCIS (Netherlands)

Havermans, J.B.G.A.

2014-01-01

The emission of (di)isocyantes, polyols and blowing agents from curing Spray Polyurethane Foam (SPF) was studied in a house having its crawl space recently insulated. Before insulation a blank measurement was made and he emission was followed up to 144 hours after the insolation application. The

Method of fabricating nested shells and resulting product

Science.gov (United States)

Henderson, Timothy M.; Kool, Lawrence B.

1982-01-01

A multiple shell structure and a method of manufacturing such structure wherein a hollow glass microsphere is surface treated in an organosilane solution so as to render the shell outer surface hydrophobic. The surface treated glass shell is then suspended in the oil phase of an oil-aqueous phase dispersion. The oil phase includes an organic film-forming monomer, a polymerization initiator and a blowing agent. A polymeric film forms at each phase boundary of the dispersion and is then expanded in a blowing operation so as to form an outer homogeneously integral monocellular substantially spherical thermoplastic shell encapsulating an inner glass shell of lesser diameter.

Failure of Sterne- and Pasteur-like strains of Bacillus anthracis to replicate and survive in the urban bluebottle blow fly Calliphora vicina under laboratory conditions.

Directory of Open Access Journals (Sweden)

Britta von Terzi

Full Text Available This study aimed to elucidate the bacteriological events occurring within the gut of Calliphora vicina, selected as the European representative of blow flies held responsible for the spread of anthrax during epidemics in certain parts of the world. Green-fluorescent-protein-carrying derivatives of Bacillus anthracis were used. These lacked either one of the virulence plasmids pXO1 and pXO2 and were infected, or not infected, with a worm intestine phage (Wip4 known to influence the phenotype and survival of the pathogen. Blood meals were prepared for the flies by inoculation of sheep blood with germinated and, in case of pXO2+ strains, encapsulated cells of the four B. anthracis strains. After being fed for 4 h an initial 10 flies were externally disinfected with peracetic acid to ensure subsequent quantitation representing ingested B. anthracis only. Following neutralization, they were crushed in sterile saline. Over each of the ensuing 7 to 10 days, 10 flies were removed and processed the same way. In the absence of Wip4, strains showed steady declines to undetectable in the total B. anthracis counts, within 7-9 days. With the phage infected strains, the falls in viable counts were significantly more rapid than in their uninfected counterparts. Spores were detectable in flies for longer periods than vegetative bacteria. In line with the findings in both biting and non-biting flies of early workers our results indicate that B. anthracis does not multiply in the guts of blow flies and survival is limited to a matter of days.

Preparation of polyurethane foams using liquefied oil palm mesocarp fibre (OPMF) and renewable monomer from waste cooking oil

Science.gov (United States)

Kormin, Shaharuddin; Rus, Anika Zafiah M.; Azahari, M. Shafiq M.

2017-09-01

The aim of this research is the production of polyurethane (PU) foams with biopolyols from liquefied oil palm mesocarp fibre (OPMF) and renewable monomer. Liquefaction of OPMF was studied using polyhydric alcohol (PA) which is PEG-400 as liquefaction solvents in conventional glass flask. In the second part of this paper was obtained the PU foams which presented good results when compared with commercial foams and include polyols from of fossil fuels. PU foams were prepared by mixing liquefied OPMF biopolyol, renewable monomer from waste cooking, additives and methylene diphenyl diisocyanate (MDI). Water was used as an environmental friendly blowing agent. The factors that influence the cell structure of foams (i.e., catalyst, surfactant, dosage of blowing agent, and mass ratio of biopolyol to renewable monomer were studied. The synthesized PU foams were characterized by FTIR and SEM. The formulation of the PU foams should be improved, but the results show that is possible the use biopolyols and renewable monomer to produce industrial foams with lower cost.

Tracking movement and temperature selection of larvae of two forensically important blow fly species within a "maggot mass".

Science.gov (United States)

Johnson, Aidan P; Wighton, Samuel J; Wallman, James F

2014-11-01

The current study responds to the lack of understanding about the temperatures experienced by individual blow fly larvae within "maggot masses." The temperature selection of both aggregating (in a mass) and nonaggregating larvae was compared and their pattern of movement assessed. Infrared imaging determined the temperatures within a mass and in the vicinity of the constituent individual larvae, whose movements were tracked by dyeing their tissues red. Individual Chrysomya rufifacies larvae selected temperatures above 27°C, significantly higher than the temperature selected by Calliphora vicina larvae (24.5°C). However, this same difference was not seen within a mass, with both species selecting temperatures around 28°C. Larval movement in a mass was nonrandom, indicating that larvae actively select their position in a mass. Furthermore, larvae have a strong tendency to select the hottest part of a mass; therefore, maximum mass temperatures might provide a reliable proxy for the actual temperatures experienced by larvae. © 2014 American Academy of Forensic Sciences.

Optimization of total vaporization solid-phase microextraction (TV-SPME) for the determination of lipid profiles of Phormia regina, a forensically important blow fly species.

Science.gov (United States)

Kranz, William; Carroll, Clinton; Dixon, Darren; Picard, Christine; Goodpaster, John

2017-11-01

A new method has been developed for the determination of fatty acids, sterols, and other lipids which naturally occur within pupae of the blow fly Phormia regina. The method relies upon liquid extraction in non-polar solvent, followed by derivatization using N,O-bis(trimethylsilyl)trifluoroacetamide (BSTFA) w/ 1% trimethylchlorsilane (TMCS) carried out inside the sample vial. The analysis is facilitated by total vaporization solid-phase microextraction (TV-SPME), with gas chromatography-mass spectrometry (GC-MS) serving as the instrumentation for analysis. The TV-SPME delivery technique is approximately a factor of five more sensitive than traditional liquid injection, which may alleviate the need for rotary evaporation, reconstitution, collection of high performance liquid chromatography fractions, and many of the other pre-concentration steps that are commonplace in the current literature. Furthermore, the ability to derivatize the liquid extract in a single easy step while increasing sensitivity represents an improvement over current derivatization methods. The most common lipids identified in fly pupae were various saturated and unsaturated fatty acids ranging from lauric acid (12:0) to arachinoic acid (20:4), as well as cholesterol. The concentrations of myristic acid (14:0), palmitelaidic acid (16:2), and palmitoleic acid (16:1) were the most reliable indicators of the age of the pupae. Graphical abstract Blow fly pupae were extracted prior to emerging as adults. The extracts were analyzed via total vaporization solid-phase microextraction (TV-SPME), revealing a complex mixture of lipids that could be associated with the age of the insect. This information may assist in determining a post-mortum interval (PMI) in a death investigation.

Multi-Agent Pathfinding with n Agents on Graphs with n Vertices

DEFF Research Database (Denmark)

Förster, Klaus-Tycho; Groner, Linus; Hoefler, Torsten

2017-01-01

We investigate the multi-agent pathfinding (MAPF) problem with $n$ agents on graphs with $n$ vertices: Each agent has a unique start and goal vertex, with the objective of moving all agents in parallel movements to their goal s.t.~each vertex and each edge may only be used by one agent at a time....... We give a combinatorial classification of all graphs where this problem is solvable in general, including cases where the solvability depends on the initial agent placement. Furthermore, we present an algorithm solving the MAPF problem in our setting, requiring O(n²) rounds, or O(n³) moves...... of individual agents. Complementing these results, we show that there are graphs where Omega(n²) rounds and Omega(n³) moves are required for any algorithm....

Experimental Study of Flow Boiling Heat Transfer in a Horizontal Microfin Tube

OpenAIRE

Yu, Jian; Koyama, Shigeru; Momoki, Satoru

1995-01-01

An experimental study on flow boiling heat transfer in a horizontal microfin tube is conducted with pure refrigerants HFC134a, HCFC123 and HCFC22 using a water-heated double-tube type test section. The test microfin tube is a copper tube having the following dimensions: 8.37mm mean inside diameter, 0.168mm fin height, 60fin number and 18 degree of helix angle. The local heat transfer coefficients for both counter and parallel flows are measured in a range of heat flux of 1 to 93W/m^2, mass ve...

9th KES Conference on Agent and Multi-Agent Systems : Technologies and Applications

CERN Document Server

Howlett, Robert; Jain, Lakhmi

2015-01-01

Agents and multi-agent systems are related to a modern software paradigm which has long been recognized as a promising technology for constructing autonomous, complex and intelligent systems. The topics covered in this volume include agent-oriented software engineering, agent co-operation, co-ordination, negotiation, organization and communication, distributed problem solving, specification of agent communication languages, agent privacy, safety and security, formalization of ontologies and conversational agents. The volume highlights new trends and challenges in agent and multi-agent research and includes 38 papers classified in the following specific topics: learning paradigms, agent-based modeling and simulation, business model innovation and disruptive technologies, anthropic-oriented computing, serious games and business intelligence, design and implementation of intelligent agents and multi-agent systems, digital economy, and advances in networked virtual enterprises. Published p...

10th International Conference on Practical Applications of Agents and Multi-Agent Systems

CERN Document Server

Pérez, Javier; Golinska, Paulina; Giroux, Sylvain; Corchuelo, Rafael; Trends in Practical Applications of Agents and Multiagent Systems

2012-01-01

PAAMS, the International Conference on Practical Applications of Agents and Multi-Agent Systems is an evolution of the International Workshop on Practical Applications of Agents and Multi-Agent Systems. PAAMS is an international yearly tribune to present, to discuss, and to disseminate the latest developments and the most important outcomes related to real-world applications. It provides a unique opportunity to bring multi-disciplinary experts, academics and practitioners together to exchange their experience in the development of Agents and Multi-Agent Systems.   This volume presents the papers that have been accepted for the 2012 in the workshops: Workshop on Agents for Ambient Assisted Living, Workshop on Agent-Based Solutions for Manufacturing and Supply Chain and Workshop on Agents and Multi-agent systems for Enterprise Integration.

Riot Control Agents

Science.gov (United States)

... Submit What's this? Submit Button Facts About Riot Control Agents Interim document Recommend on Facebook Tweet Share Compartir What riot control agents are Riot control agents (sometimes referred to ...

Intrinsic Flame-Retardant and Thermally Stable Epoxy Endowed by a Highly Efficient, Multifunctional Curing Agent

Directory of Open Access Journals (Sweden)

Chunlei Dong

2016-12-01

Full Text Available It is difficult to realize flame retardancy of epoxy without suffering much detriment in thermal stability. To solve the problem, a super-efficient phosphorus-nitrogen-containing reactive-type flame retardant, 10-(hydroxy(4-hydroxyphenylmethyl-5,10-dihydrophenophosphazinine-10-oxide (HB-DPPA is synthesized and characterized. When it is used as a co-curing agent of 4,4′-methylenedianiline (DDM for curing diglycidyl ether of bisphenol A (DGEBA, the cured epoxy achieves UL-94 V-0 rating with the limiting oxygen index of 29.3%. In this case, the phosphorus content in the system is exceptionally low (0.18 wt %. To the best of our knowledge, it currently has the highest efficiency among similar epoxy systems. Such excellent flame retardancy originates from the exclusive chemical structure of the phenophosphazine moiety, in which the phosphorus element is stabilized by the two adjacent aromatic rings. The action in the condensed phase is enhanced and followed by pressurization of the pyrolytic gases that induces the blowing-out effect during combustion. The cone calorimeter result reveals the formation of a unique intumescent char structure with five discernible layers. Owing to the super-efficient flame retardancy and the rigid molecular structure of HB-DPPA, the flame-retardant epoxy acquires high thermal stability and its initial decomposition temperature only decreases by 4.6 °C as compared with the unmodified one.

Constructing Secure Mobile Agent Systems Using the Agent Operating System

NARCIS (Netherlands)

van t Noordende, G.J.; Overeinder, B.J.; Timmer, R.J.; Brazier, F.M.; Tanenbaum, A.S.

2009-01-01

Designing a secure and reliable mobile agent system is a difficult task. The agent operating system (AOS) is a building block that simplifies this task. AOS provides common primitives required by most mobile agent middleware systems, such as primitives for secure communication, secure and

Nondestructive Intervention to Multi-Agent Systems through an Intelligent Agent

Science.gov (United States)

Han, Jing; Wang, Lin

2013-01-01

For a given multi-agent system where the local interaction rule of the existing agents can not be re-designed, one way to intervene the collective behavior of the system is to add one or a few special agents into the group which are still treated as normal agents by the existing ones. We study how to lead a Vicsek-like flocking model to reach synchronization by adding special agents. A popular method is to add some simple leaders (fixed-headings agents). However, we add one intelligent agent, called ‘shill’, which uses online feedback information of the group to decide the shill's moving direction at each step. A novel strategy for the shill to coordinate the group is proposed. It is strictly proved that a shill with this strategy and a limited speed can synchronize every agent in the group. The computer simulations show the effectiveness of this strategy in different scenarios, including different group sizes, shill speed, and with or without noise. Compared to the method of adding some fixed-heading leaders, our method can guarantee synchronization for any initial configuration in the deterministic scenario and improve the synchronization level significantly in low density groups, or model with noise. This suggests the advantage and power of feedback information in intervention of collective behavior. PMID:23658695

Nondestructive intervention to multi-agent systems through an intelligent agent.

Directory of Open Access Journals (Sweden)

Jing Han

Full Text Available For a given multi-agent system where the local interaction rule of the existing agents can not be re-designed, one way to intervene the collective behavior of the system is to add one or a few special agents into the group which are still treated as normal agents by the existing ones. We study how to lead a Vicsek-like flocking model to reach synchronization by adding special agents. A popular method is to add some simple leaders (fixed-headings agents. However, we add one intelligent agent, called 'shill', which uses online feedback information of the group to decide the shill's moving direction at each step. A novel strategy for the shill to coordinate the group is proposed. It is strictly proved that a shill with this strategy and a limited speed can synchronize every agent in the group. The computer simulations show the effectiveness of this strategy in different scenarios, including different group sizes, shill speed, and with or without noise. Compared to the method of adding some fixed-heading leaders, our method can guarantee synchronization for any initial configuration in the deterministic scenario and improve the synchronization level significantly in low density groups, or model with noise. This suggests the advantage and power of feedback information in intervention of collective behavior.

How clarinettists articulate: The effect of blowing pressure and tonguing on initial and final transients.

Science.gov (United States)

Li, Weicong; Almeida, André; Smith, John; Wolfe, Joe

2016-02-01

Articulation, including initial and final note transients, is important to tasteful music performance. Clarinettists' tongue-reed contact, the time variation of the blowing pressure P¯mouth, the mouthpiece pressure, the pressure in the instrument bore, and the radiated sound were measured for normal articulation, accents, sforzando, staccato, and for minimal attack, i.e., notes started very softly. All attacks include a phase when the amplitude of the fundamental increases exponentially, with rates r ∼1000 dB s(-1) controlled by varying both the rate of increase in P¯mouth and the timing of tongue release during this increase. Accented and sforzando notes have shorter attacks (r∼1300 dB s(-1)) than normal notes. P¯mouth reaches a higher peak value for accented and sforzando notes, followed by a steady decrease for accented notes or a rapid fall to a lower, nearly steady value for sforzando notes. Staccato notes are usually terminated by tongue contact, producing an exponential decrease in sound pressure with rates similar to those calculated from the bandwidths of the bore resonances: ∼400 dB s(-1). In all other cases, notes are stopped by decreasing P¯mouth. Notes played with different dynamics are qualitatively similar, but louder notes have larger P¯mouth and larger r.

Organizations as Socially Constructed Agents in the Agent Oriented Paradigm

NARCIS (Netherlands)

G. Boella (Guido); L.W.N. van der Torre (Leon)

2005-01-01

htmlabstractIn this paper we propose a new role for the agent metaphor in the definition of the organizational structure of multiagent systems. The agent metaphor is extended to consider as agents also social entities like organizations, groups and normative systems, so that mental attitudes can

Neuroprotective "agents" in surgery. Secret "agent" man, or common "agent" machine?

Science.gov (United States)

Andrews, R. J.

1999-01-01

The search for clinically-effective neuroprotective agents has received enormous support in recent years--an estimated $200 million by pharmaceutical companies on clinical trials for traumatic brain injury alone. At the same time, the pathophysiology of brain injury has proved increasingly complex, rendering the likelihood of a single agent "magic bullet" even more remote. On the other hand, great progress continues with technology that makes surgery less invasive and less risky. One example is the application of endovascular techniques to treat coronary artery stenosis, where both the invasiveness of sternotomy and the significant neurological complication rate (due to microemboli showering the cerebral vasculature) can be eliminated. In this paper we review aspects of intraoperative neuroprotection both present and future. Explanations for the slow progress on pharmacologic neuroprotection during surgery are presented. Examples of technical advances that have had great impact on neuroprotection during surgery are given both from coronary artery stenosis surgery and from surgery for Parkinson's disease. To date, the progress in neuroprotection resulting from such technical advances is an order of magnitude greater than that resulting from pharmacologic agents used during surgery. The progress over the last 20 years in guidance during surgery (CT and MRI image-guidance) and in surgical access (endoscopic and endovascular techniques) will soon be complemented by advances in our ability to evaluate biological tissue intraoperatively in real-time. As an example of such technology, the NASA Smart Probe project is considered. In the long run (i.e., in 10 years or more), pharmacologic "agents" aimed at the complex pathophysiology of nervous system injury in man will be the key to true intraoperative neuroprotection. In the near term, however, it is more likely that mundane "agents" based on computers, microsensors, and microeffectors will be the major impetus to improved

MRI brain in monohalomethane toxic encephalopathy: A case report

Directory of Open Access Journals (Sweden)

Yogeshwari S Deshmukh

2013-01-01

Full Text Available Monohalomethanes are alkylating agents that have been used as methylating agents, laboratory reagents, refrigerants, aerosol propellants, pesticides, fumigants, fire-extinguishing agents, anesthetics, degreasers, blowing agents for plastic foams, and chemical intermediates. Compounds in this group are methyl chloride, methyl bromide, methyl iodide (MI, and methyl fluoride. MI is a colorless volatile liquid used as a methylating agent to manufacture a few pharmaceuticals and is also used as a fumigative insecticide. It is a rare intoxicant. Neurotoxicity is known with both acute and chronic exposure to MI. We present the characteristic magnetic resonance imaging (MRI brain findings in a patient who developed neuropsychiatric symptoms weeks after occupational exposure to excessive doses of MI.

MRI brain in monohalomethane toxic encephalopathy: A case report

International Nuclear Information System (INIS)

Deshmukh, Yogeshwari S; Atre, Ashish; Shah, Darshan; Kothari, Sudhir

2013-01-01

Monohalomethanes are alkylating agents that have been used as methylating agents, laboratory reagents, refrigerants, aerosol propellants, pesticides, fumigants, fire-extinguishing agents, anesthetics, degreasers, blowing agents for plastic foams, and chemical intermediates. Compounds in this group are methyl chloride, methyl bromide, methyl iodide (MI), and methyl fluoride. MI is a colorless volatile liquid used as a methylating agent to manufacture a few pharmaceuticals and is also used as a fumigative insecticide. It is a rare intoxicant. Neurotoxicity is known with both acute and chronic exposure to MI. We present the characteristic magnetic resonance imaging (MRI) brain findings in a patient who developed neuropsychiatric symptoms weeks after occupational exposure to excessive doses of MI

Advances on Practical Applications of Agents and Multi-Agent Systems 10th International Conference on Practical Applications of Agents and Multi-Agent Systems

CERN Document Server

Müller, Jörg; Rodríguez, Juan; Pérez, Javier

2012-01-01

Research on Agents and Multi-Agent Systems has matured during the last decade and many effective applications of this technology are now deployed. PAAMS provides an international forum to present and discuss the latest scientific developments and their effective applications, to assess the impact of the approach, and to facilitate technology transfer. PAAMS started as a local initiative, but has since grown to become THE international yearly platform to present, to discuss, and to disseminate the latest developments and the most important outcomes related to real-world applications. It provides a unique opportunity to bring multi-disciplinary experts, academics and practitioners together to exchange their experience in the development and deployment of Agents and Multi-Agent Systems. PAAMS intends to bring together researchers and developers from industry and the academic world to report on the latest scientific and technical advances on the application of multi-agent systems, to discuss and debate the major ...

Highlights on Practical Applications of Agents and Multi-Agent Systems 10th International Conference on Practical Applications of Agents and Multi-Agent Systems

CERN Document Server

Sánchez, Miguel; Mathieu, Philippe; Rodríguez, Juan; Adam, Emmanuel; Ortega, Alfonso; Moreno, María; Navarro, Elena; Hirsch, Benjamin; Lopes-Cardoso, Henrique; Julián, Vicente

2012-01-01

Research on Agents and Multi-Agent Systems has matured during the last decade and many effective applications of this technology are now deployed. PAAMS provides an international forum to present and discuss the latest scientific developments and their effective applications, to assess the impact of the approach, and to facilitate technology transfer. PAAMS started as a local initiative, but has since grown to become THE international yearly platform to present, to discuss, and to disseminate the latest developments and the most important outcomes related to real-world applications. It provides a unique opportunity to bring multi-disciplinary experts, academics and practitioners together to exchange their experience in the development and deployment of Agents and Multi-Agent Systems. PAAMS intends to bring together researchers and developers from industry and the academic world to report on the latest scientific and technical advances on the application of multi-agent systems, to discuss and debate the major ...

Intumescent all-polymer multilayer nanocoating capable of extinguishing flame on fabric

Science.gov (United States)

Cotton fabric was treated with flame-retardant coatings composed of poly (sodium phosphate), PSP, which acts as the acid source, and poly (allylamine), PAAm, which is used as the blowing agent, prepared via layer-by-layer (LbL) assembly. By applying these thin coating on fabric, after-glow is elimi...

The main elements to consider when designing an arena; Les principaux elements a determiner lors de la conception d'un arena

Energy Technology Data Exchange (ETDEWEB)

Gosselin, M. [Fixair Inc., Quebec, PQ (Canada)

2010-01-01

The refrigeration systems in Quebec's arenas are aging, with most installations dating from the 1970s or 1980s. Most arenas use HCFC R-22 as the coolant, which is a regulated substance in Montreal and should be eliminated by 2020. The price of HCFC R-22 has also increased recently and a shortage is expected. This paper presented the choice of coolants that can be used as a replacement for HCFC R-22. The 3 main options include ammonia R-717; HFC R-404A or R-507A; and carbon dioxide (CO{sub 2}) R-744. This article listed the advantages and disadvantages of each option. It also described the secondary coolant that goes under the ice. The 4 types of secondary coolant include calcium chloride, ethylene glycol, methanol and CO{sub 2}. There are also 2 choices for compressors, notably reciprocal and screw type compressors. The use of heat exchangers in arenas will be instrumental in using waste heat for water heating and space heating purposes. 3 tabs., 3 figs.

Radiographic scanning agent

International Nuclear Information System (INIS)

Bevan, J.A.

1983-01-01

This invention relates to radiodiagnostic agents and more particularly to a composition and method for preparing a highly effective technetium-99m-based bone scanning agent. One deficiency of x-ray examination is the inability of that technique to detect skeletal metastases in their incipient stages. It has been discovered that the methanehydroxydiphosphonate bone mineral-seeking agent is unique in that it provides the dual benefits of sharp radiographic imaging and excellent lesion detection when used with technetium-99m. This agent can also be used with technetium-99m for detecting soft tissue calcification in the manner of the inorganic phosphate radiodiagnostic agents

Smart Agents and Sentiment in the Heterogeneous Agent Model

Czech Academy of Sciences Publication Activity Database

Vácha, Lukáš; Baruník, Jozef; Vošvrda, Miloslav

2009-01-01

Roč. 18, č. 3 (2009), s. 209-219 ISSN 1210-0455 R&D Projects: GA MŠk(CZ) LC06075; GA ČR GP402/08/P207; GA ČR(CZ) GA402/09/0965 Institutional research plan: CEZ:AV0Z10750506 Keywords : heterogeneous agent model * market structure * smart traders * Hurst exponent Subject RIV: AH - Economics http://library.utia.cas.cz/separaty/2009/E/vacha- smart agent s and sentiment in the heterogeneous agent model.pdf

Prediction of Long Term Degradation of Insulating Materials

Science.gov (United States)

2015-05-01

Mfg. Process XPA Polystyrene foam trans-1,3,3,3-Tetrafluoroprop-1-ene blowing agent Extruded XPB Polystyrene foam 1-Chloro-1,1- difluoroethane and...Honeywell 2014); the other used a combination of 1-Chloro-1,1- difluoroethane and 1,1,1,2-Tetrafluoroethane (Dow 2011). Figure 2-5(c) shows the sample

Trends in Navy Waste Reduction and Materials Markets.

Science.gov (United States)

1981-06-01

227 5,838 GENERAL PACKAGING 4,869 4,839 30 185 4,684 Aerosol 2,202 2,172 30 100 2,102 Motor Oil 546 546 -0- -0- 546 Paint & Varnish 873 873 -0- -0- 873...antioxidants, antistats, blowing agents, colorants, fluorine retardants, organic peroxides, plasticizers and ultraviolet stabilizers can be added to

Asymptotically Optimal Agents

OpenAIRE

Lattimore, Tor; Hutter, Marcus

2011-01-01

Artificial general intelligence aims to create agents capable of learning to solve arbitrary interesting problems. We define two versions of asymptotic optimality and prove that no agent can satisfy the strong version while in some cases, depending on discounting, there does exist a non-computable weak asymptotically optimal agent.

Further Understanding of Theories and Practice for Low-Cost and High-Efficient Clean Steel Production by Combined Blowing Converter%对复吹转炉低成本、高效化生产洁净钢水理论与实践的再认识

Institute of Scientific and Technical Information of China (English)

曾加庆; 潘贻芳; 王立平; 梁玫; 李树庆

2014-01-01

Based on review of development about the processes of clean steel production at home and abroad, the techni-cal principles and their necessities of low-cost and high-efficient clean steel production by combined blowing converter were analyzed, including low-temperature dephosphorization by combined blowing converter, the coordination of top and bottom blowing, the continuous implementation of the new process, the high-efficient oxygen blowing in decarburization period, and the reutilization method of slag been rich in P2O5, and so on. In order to obtain good implementation effect of the new process, the comprehensive and objective technical key points of the new process must be known well, and also the solid foundation of technical and management would be needed. According to related problems occurred in practice, the improved proposals were put forward.%在回顾总结国内外开展洁净钢水生产技术发展过程的基础上，对复吹转炉低成本、高效化生产洁净钢水工艺的技术原理及相关必要性进行了分析，包括复吹转炉低温脱磷、顶吹与底吹的协同作用、新工艺的连续化实施、脱碳期高效供氧、脱磷炉渣资源化技术途径等。认为要获得好的工艺实施效果，不仅要全面客观地掌握新工艺实施的技术要点，更要具备一定的技术与精细化管理基础。结合新工艺在生产实践中出现的具体问题，提出了改进建议。

Traitement de l'hétérogénéité sémantique dans les interactions humain-agent et agent-agent

OpenAIRE

Mazuel , Laurent

2008-01-01

The main purpose of this thesis is the management of semantic heterogeneity in human-agent and agent-agent interaction. We especially focus on the situation where a software agent, supplied with a knowledge representation model, has to understand requests coming from different interlocutors; either it is a human user or another software agent.Most work in this domain either focus on human-agent interaction or agent-agent interaction. On the contrary, we suggest that it is possible to use a co...

Relay tracking control for second-order multi-agent systems with damaged agents.

Science.gov (United States)

Dong, Lijing; Li, Jing; Liu, Qin

2017-11-01

This paper investigates a situation where smart agents capable of sensory and mobility are deployed to monitor a designated area. A preset number of agents start tracking when a target intrudes this area. Some of the tracking agents are possible to be out of order over the tracking course. Thus, we propose a cooperative relay tracking strategy to ensure the successful tracking with existence of damaged agents. Relay means that, when a tracking agent quits tracking due to malfunction, one of the near deployed agents replaces it to continue the tracking task. This results in jump of tracking errors and dynamic switching of topology of the multi-agent system. Switched system technique is employed to solve this specific problem. Finally, the effectiveness of proposed tracking strategy and validity of the theoretical results are verified by conducting a numerical simulation. Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.

Agentes Comunitários de Saúde e os sentidos de "ser agente" Community Health Agents and the meanings of "being an agent"

Directory of Open Access Journals (Sweden)

Viviane Milan Pupin

2008-08-01

Full Text Available O Programa Saúde da Família constitui-se enquanto estratégia de mudança do modelo assistencial. O artigo apresenta os resultados de uma pesquisa qualitativa sobre os sentidos de "ser agente" produzidos, por meio de entrevistas abertas, com Agentes Comunitários de Saúde que trabalham nos cinco Núcleos de Saúde da Família da cidade de Ribeirão Preto - São Paulo, vinculados à Faculdade de Medicina de Ribeirão Preto - USP. As entrevistas foram gravadas e transcritas na íntegra e analisadas segundo princípios da análise de conteúdo. A análise permitiu a descrição de sentidos acerca de ser agente subdivididos em: Sentidos produzidos na relação com a comunidade e Sentidos produzidos na relação com a equipe. A análise dos sentidos de ser agente possibilitou construir um diálogo sobre as tensões relacionadas a um fazer em saúde ora permeado por concepções atreladas ao modelo biomédico, ora atrelado aos novos paradigmas em saúde.The Family Health Program consists of a strategy to change the health care model. This article presents the results from a qualitative study about the meanings of "being an agent" obtained through open interviews with Community Health Agents who work in five Family Health Centers of the Ribeirão Preto School of Medicine (University of São Paulo, located in Ribeirão Preto, São Paulo. Interviews were tape recorded, fully transcribed, and then content analyzed. The analysis allowed for descriptions of meanings toward "being an agent", subdivided into: Meanings produced by relationships with the community, and Meanings produced by relationships with the team. Analyzing the meanings of being an agent provided the establishment of a dialogue about the tensions related to a health practice that is at times influenced by conceptions associated with the biomedical method, and at other times with the new health paradigm.

Biological warfare agents

Directory of Open Access Journals (Sweden)

Duraipandian Thavaselvam

2010-01-01

Full Text Available The recent bioterrorist attacks using anthrax spores have emphasized the need to detect and decontaminate critical facilities in the shortest possible time. There has been a remarkable progress in the detection, protection and decontamination of biological warfare agents as many instrumentation platforms and detection methodologies are developed and commissioned. Even then the threat of biological warfare agents and their use in bioterrorist attacks still remain a leading cause of global concern. Furthermore in the past decade there have been threats due to the emerging new diseases and also the re-emergence of old diseases and development of antimicrobial resistance and spread to new geographical regions. The preparedness against these agents need complete knowledge about the disease, better research and training facilities, diagnostic facilities and improved public health system. This review on the biological warfare agents will provide information on the biological warfare agents, their mode of transmission and spread and also the detection systems available to detect them. In addition the current information on the availability of commercially available and developing technologies against biological warfare agents has also been discussed. The risk that arise due to the use of these agents in warfare or bioterrorism related scenario can be mitigated with the availability of improved detection technologies.

Biological warfare agents

Science.gov (United States)

Thavaselvam, Duraipandian; Vijayaraghavan, Rajagopalan

2010-01-01

The recent bioterrorist attacks using anthrax spores have emphasized the need to detect and decontaminate critical facilities in the shortest possible time. There has been a remarkable progress in the detection, protection and decontamination of biological warfare agents as many instrumentation platforms and detection methodologies are developed and commissioned. Even then the threat of biological warfare agents and their use in bioterrorist attacks still remain a leading cause of global concern. Furthermore in the past decade there have been threats due to the emerging new diseases and also the re-emergence of old diseases and development of antimicrobial resistance and spread to new geographical regions. The preparedness against these agents need complete knowledge about the disease, better research and training facilities, diagnostic facilities and improved public health system. This review on the biological warfare agents will provide information on the biological warfare agents, their mode of transmission and spread and also the detection systems available to detect them. In addition the current information on the availability of commercially available and developing technologies against biological warfare agents has also been discussed. The risk that arise due to the use of these agents in warfare or bioterrorism related scenario can be mitigated with the availability of improved detection technologies. PMID:21829313

14th International Conference on Practical Applications of Agents and Multi-Agent Systems : Special Sessions

CERN Document Server

Escalona, María; Corchuelo, Rafael; Mathieu, Philippe; Vale, Zita; Campbell, Andrew; Rossi, Silvia; Adam, Emmanuel; Jiménez-López, María; Navarro, Elena; Moreno, María

2016-01-01

PAAMS, the International Conference on Practical Applications of Agents and Multi-Agent Systems is an evolution of the International Workshop on Practical Applications of Agents and Multi-Agent Systems. PAAMS is an international yearly tribune to present, to discuss, and to disseminate the latest developments and the most important outcomes related to real-world applications. It provides a unique opportunity to bring multi-disciplinary experts, academics and practitioners together to exchange their experience in the development of Agents and Multi-Agent Systems. This volume presents the papers that have been accepted for the 2016 in the special sessions: Agents Behaviours and Artificial Markets (ABAM); Advances on Demand Response and Renewable Energy Sources in Agent Based Smart Grids (ADRESS); Agents and Mobile Devices (AM); Agent Methodologies for Intelligent Robotics Applications (AMIRA); Learning, Agents and Formal Languages (LAFLang); Multi-Agent Systems and Ambient Intelligence (MASMAI); Web Mining and ...

Morphologies, Processing and Properties of Ceramic Foams and Their Potential as TPS Materials

Science.gov (United States)

Stackpoole, Mairead; Simoes, Conan R.; Johnson, Sylvia M.

2002-01-01

The current research is focused on processing ceramic foams with compositions that have potential as a thermal protection material. The use of pre-ceramic polymers with the addition of sacrificial blowing agents or sacrificial fillers offers a viable approach to form either open or closed cell insulation. Our work demonstrates that this is a feasible method to form refractory ceramic foams at relatively low processing temperatures. It is possible to foam complex shapes then pyrolize the system to form a ceramic while retaining the shape of the unfired foam. Initial work focused on identifying suitable pre-ceramic polymers with desired properties such as ceramic yield and chemical make up of the pyrolysis product after firing. We focused on making foams in the Si system (Sic, Si02, Si-0-C), which is in use in current acreage TPS systems. Ceramic foams with different architectures were formed from the pyrolysis of pre-ceramic polymers at 1200 C in different atmospheres. In some systems a sacrificial polyurethane was used as the blowing agent. We have also processed foams using sacrificial fillers to introduce controlled cell sizes. Each sacrificial filler or blowing agent leads to a unique morphology. The effect of different fillers on foam morphologies and the characterization of these foams in terms of mechanical and thermal properties are presented. We have conducted preliminary arc jet testing on selected foams with the materials being exposed to typical re-entry conditions for acreage TPS and these results will be discussed. Foams processed using these approaches have bulk densities ranging from 0.15 to 0.9 g/cm3 and cell sizes ranging from 5 to 500 pm. Compression strengths ranged from 2 to 7 MPa for these systems. Finally, preliminary oxidation studies have been conducted on selected systems and will be discussed.

Foam, composition and method of production

Energy Technology Data Exchange (ETDEWEB)

Ghali, R.

1991-09-03

A ternary foam is disclosed which overcomes the disadvantages of conventional heat-insulating foams which are either dense and heavy, expensive to produce, friable, unstable, or have poor fire resistance. The foam of the invention has, by weight of the reaction product, 10-35% polyurethane, 30-55% polyisocyanurate, and 20-45% polyurea. The foam is a reaction product of 100 parts by weight of an organic polyisocyanate with: 15-25 parts by weight of a polyether polyol having a hydroxyl number of ca 28-35 and a molecular weight of not more than 6,000; 5-25 parts by weight of water; 0-25 parts by weight of a blowing agent; 0-50 parts by weight of a filler-plasticizer fire retardant; an effective amount of a low activation catalyst to initiate water-isocyanate reaction to produce polyurea and polyol-isocyanate reaction to produce polyurethane; and an effective amount of a high activation catalyst to retard the low activation catalyst and promote the formation of polyisocyanurate. The low activity catalyst is present in an amount ranging ca 1.5-9 parts per 100 parts by weight of the polyisocyanate, and the high activation catalyst is present in an amount ranging 0.0008-0.002 parts per 100 parts by weight of the polyisocyanate. Water as a reactant and blowing agent can be substituted by an effective amount of a disubstituted amine such as diethanol amine and an inert blowing agent such as fluorocarbon. The resultant foam has excellent heat insulating propeties, is semi-flexible, has a density of 0.5-0.9 lb/ft{sup 3}, and can be inexpensively produced by existing 2-component foam dispensing equipment. 1 fig., 1 tab.

Developing Agent-Oriented Video Surveillance System through Agent-Oriented Methodology (AOM

Directory of Open Access Journals (Sweden)

Cheah Wai Shiang

2016-12-01

Full Text Available Agent-oriented methodology (AOM is a comprehensive and unified agent methodology for agent-oriented software development. Although AOM is claimed to be able to cope with a complex system development, it is still not yet determined up to what extent this may be true. Therefore, it is vital to conduct an investigation to validate this methodology. This paper presents the adoption of AOM in developing an agent-oriented video surveillance system (VSS. An intruder handling scenario is designed and implemented through AOM. AOM provides an alternative method to engineer a distributed security system in a systematic manner. It presents the security system at a holistic view; provides a better conceptualization of agent-oriented security system and supports rapid prototyping as well as simulation of video surveillance system.

Structural Foams of Biobased Isosorbide-Containing Copolycarbonate

Directory of Open Access Journals (Sweden)

Stefan Zepnik

2017-01-01

Full Text Available Isosorbide-containing copolycarbonate (Bio-PC is a partly biobased alternative to conventional bisphenol A (BPA based polycarbonate (PC. Conventional PC is widely used in polymer processing technologies including thermoplastic foaming such as foam injection molding. At present, no detailed data is available concerning the foam injection molding behavior and foam properties of Bio-PC. This contribution provides first results on injection-molded foams based on isosorbide-containing PC. The structural foams were produced by using an endothermic chemical blowing agent (CBA masterbatch and the low pressure foam injection molding method. The influence of weight reduction and blowing agent concentration on general foam properties such as density, morphology, and mechanical properties was studied. The test specimens consist of a foam core in the center and compact symmetrical shell layers on the sides. The thickness of the foam core increases with increasing weight reduction irrespective of the CBA concentration. The specific (mechanical bending properties are significantly improved and the specific tensile properties can almost be maintained while reducing the density of the injection-molded parts.

Agent Architectures for Compliance

Science.gov (United States)

Burgemeestre, Brigitte; Hulstijn, Joris; Tan, Yao-Hua

A Normative Multi-Agent System consists of autonomous agents who must comply with social norms. Different kinds of norms make different assumptions about the cognitive architecture of the agents. For example, a principle-based norm assumes that agents can reflect upon the consequences of their actions; a rule-based formulation only assumes that agents can avoid violations. In this paper we present several cognitive agent architectures for self-monitoring and compliance. We show how different assumptions about the cognitive architecture lead to different information needs when assessing compliance. The approach is validated with a case study of horizontal monitoring, an approach to corporate tax auditing recently introduced by the Dutch Customs and Tax Authority.

A Secure Protocol Based on a Sedentary Agent for Mobile Agent Environments

OpenAIRE

Abdelmorhit E. Rhazi; Samuel Pierre; Hanifa Boucheneb

2007-01-01

The main challenge when deploying mobile agent environments pertains to security issues concerning mobile agents and their executive platform. This paper proposes a secure protocol which protects mobile agents against attacks from malicious hosts in these environments. Protection is based on the perfect cooperation of a sedentary agent running inside a trusted third host. Results show that the protocol detects several attacks, such as denial of service, incorrect execution and re-execution of...

Moral actor, selfish agent.

Science.gov (United States)

Frimer, Jeremy A; Schaefer, Nicola K; Oakes, Harrison

2014-05-01

People are motivated to behave selfishly while appearing moral. This tension gives rise to 2 divergently motivated selves. The actor-the watched self-tends to be moral; the agent-the self as executor-tends to be selfish. Three studies present direct evidence of the actor's and agent's distinct motives. To recruit the self-as-actor, we asked people to rate the importance of various goals. To recruit the self-as-agent, we asked people to describe their goals verbally. In Study 1, actors claimed their goals were equally about helping the self and others (viz., moral); agents claimed their goals were primarily about helping the self (viz., selfish). This disparity was evident in both individualist and collectivist cultures, attesting to the universality of the selfish agent. Study 2 compared actors' and agents' motives to those of people role-playing highly prosocial or selfish exemplars. In content (Study 2a) and in the impressions they made on an outside observer (Study 2b), actors' motives were similar to those of the prosocial role-players, whereas agents' motives were similar to those of the selfish role-players. Study 3 accounted for the difference between the actor and agent: Participants claimed that their agent's motives were the more realistic and that their actor's motives were the more idealistic. The selfish agent/moral actor duality may account for why implicit and explicit measures of the same construct diverge, and why feeling watched brings out the better angels of human nature.

The Agent of Change: The Agent of Conflict.

Science.gov (United States)

Hatfield, C. R., Jr.

This speech examines the role of change agents in third world societies and indicates that the change agent must, to some extent, manipulate the social situation, even if his view of society is a more optimistic one than he finds in reality. If he considers strains and stresses to be the lubricants of change, then his focus on conflict as a…

Interactions of ionic and nonionic contrast agents with thrombolytic agents

International Nuclear Information System (INIS)

Fareed, J.; Moncada, R.; Scanlon, P.; Hoppensteadt, D.; Huan, X.; Walenga, J.M.

1987-01-01

Both the ionic and nonionic intravascular contrast media have been used before and after the administration of thrombolytic agents to evaluate clot lysis during angioplasty and the treatment of myocardial infarction. In experimental animal models, the authors found that the clot lytic efficacy of streptokinase, streptokinase-plasminogen complex, and tissue plasminogen activator (t-PA) is markedly augmented if these agents are administered within 1 hour after the angiographic producers. Furthermore, contrast agents injected after the administration of t-Pa exhibit a synergistic action. In stimulated models administration of one ionic contrast medium (Angiovist, Berlex, Wayne, NJ) and two nonionic contrast agents (Isovue-370, Squibb Diagnostics, New Brunswick, NJ; Omnipaque-350, Winthrop, NY) 15 minutes before the administration of t-PA resulted in marked enhancement of the lytic activity. Although the mechanism of this interaction is unknown at this time, it should be taken into consideration in the treatment of patients with myocardial infarction, in whom contrast agents are continually used to evaluate the therapeutic lysis. Furthermore, this interaction may be partly related to the therapeutic efficacy and/or hemorrhagic actions observed

Survey of agent for intelligent information retrieval; Chiteki kensaku no tame no agent no chosa

Energy Technology Data Exchange (ETDEWEB)

Yazawa, T [Central Research Institute of Electric Power Industry, Tokyo (Japan)

1996-09-01

Development of agent systems has been surveyed, to classify and arrange characteristic functions of the agents, and to grasp the realization situation of these agents in their development. In addition, prospective functions of information retrieval systems using the agents at maximum and functions to be developed among these in the future are clarified. The agents are characterized by the expression function, communication function, planning function, adaptive function, and learning function. The agents are desired to be classified into interface agents whose works are to respond to individual workers, coordinator agents which conduct works with high pervasion, such as assignment of works and their control, and task agents which conduct specialized works for individual examples. Thus, design and configuration of the agent system, and improvement and expansion of system functions can be effectively and easily conducted. 52 refs., 5 figs., 3 tabs.

Agent and multi-Agent systems in distributed systems digital economy and e-commerce

CERN Document Server

Hartung, Ronald

2013-01-01

Information and communication technology, in particular artificial intelligence, can be used to support economy and commerce using digital means. This book is about agents and multi-agent distributed systems applied to digital economy and e-commerce to meet, improve, and overcome challenges in the digital economy and e-commerce sphere. Agent and multi-agent solutions are applied in implementing real-life, exciting developments associated with the need to eliminate problems of distributed systems.   The book presents solutions for both technology and applications, illustrating the possible uses of agents in the enterprise domain, covering design and analytic methods, needed to provide a solid foundation required for practical systems. More specifically, the book provides solutions for the digital economy, e-sourcing clusters in network economy, and knowledge exchange between agents applicable to online trading agents, and security solutions to both digital economy and e-commerce. Furthermore, it offers soluti...

Reasoning about emotional agents

OpenAIRE

Meyer, J.-J.

2004-01-01

In this paper we discuss the role of emotions in artificial agent design, and the use of logic in reasoning about the emotional or affective states an agent can reside in. We do so by extending the KARO framework for reasoning about rational agents appropriately. In particular we formalize in this framework how emotions are related to the action monitoring capabilities of an agent.

Double agents and secret agents: the emerging fields of exogenous chemical exchange saturation transfer and T2-exchange magnetic resonance imaging contrast agents for molecular imaging.

Science.gov (United States)

Daryaei, Iman; Pagel, Mark D

2015-01-01

Two relatively new types of exogenous magnetic resonance imaging contrast agents may provide greater impact for molecular imaging by providing greater specificity for detecting molecular imaging biomarkers. Exogenous chemical exchange saturation transfer (CEST) agents rely on the selective saturation of the magnetization of a proton on an agent, followed by chemical exchange of a proton from the agent to water. The selective detection of a biomarker-responsive CEST signal and an unresponsive CEST signal, followed by the ratiometric comparison of these signals, can improve biomarker specificity. We refer to this improvement as a "double-agent" approach to molecular imaging. Exogenous T 2 -exchange agents also rely on chemical exchange of protons between the agent and water, especially with an intermediate rate that lies between the slow exchange rates of CEST agents and the fast exchange rates of traditional T 1 and T 2 agents. Because of this intermediate exchange rate, these agents have been relatively unknown and have acted as "secret agents" in the contrast agent research field. This review exposes these secret agents and describes the merits of double agents through examples of exogenous agents that detect enzyme activity, nucleic acids and gene expression, metabolites, ions, redox state, temperature, and pH. Future directions are also provided for improving both types of contrast agents for improved molecular imaging and clinical translation. Therefore, this review provides an overview of two new types of exogenous contrast agents that are becoming useful tools within the armamentarium of molecular imaging.

A CSP-Based Agent Modeling Framework for the Cougaar Agent-Based Architecture

Science.gov (United States)

Gracanin, Denis; Singh, H. Lally; Eltoweissy, Mohamed; Hinchey, Michael G.; Bohner, Shawn A.

2005-01-01

Cognitive Agent Architecture (Cougaar) is a Java-based architecture for large-scale distributed agent-based applications. A Cougaar agent is an autonomous software entity with behaviors that represent a real-world entity (e.g., a business process). A Cougaar-based Model Driven Architecture approach, currently under development, uses a description of system's functionality (requirements) to automatically implement the system in Cougaar. The Communicating Sequential Processes (CSP) formalism is used for the formal validation of the generated system. Two main agent components, a blackboard and a plugin, are modeled as CSP processes. A set of channels represents communications between the blackboard and individual plugins. The blackboard is represented as a CSP process that communicates with every agent in the collection. The developed CSP-based Cougaar modeling framework provides a starting point for a more complete formal verification of the automatically generated Cougaar code. Currently it is used to verify the behavior of an individual agent in terms of CSP properties and to analyze the corresponding Cougaar society.

Considerations for the Estimation of the Risk of Environmental Contamination Due to Blow Out in Offshore Exploratory Drilling Projects

International Nuclear Information System (INIS)

Hurtado, A.; Eguilior, S.; Recreo, F.

2015-01-01

From the consideration of a contemporary society based on the need of a high-level complex technology with a high intrinsic level of uncertainty and its relationship with risk assessment, this analysis, conducted in late 2014, was developed from that that led the Secretary of State for the Environment to the Resolution of 29 May 2014, by which the Environmental Impact Statement of the Exploratory Drilling Project in the hydrocarbons research permits called ''Canarias 1-9// was set out and published in the Spanish Official State Gazette number 196 on 13rd August 2014. The aim of the present study is to analyze the suitability with which the worst case associated probability is identified and defined and its relation to the total risk estimate from a blow out. Its interest stems from the fact that all risk management methodologically rests on two pillars, i.e., on a sound risk analysis and evaluation. This determines the selection of management tools in relation to its level of complexity, the project phase and its potential impacts on the health, safety and environmental contamination dimensions.

Fundamental studies of oral contrast agents for MR. Comparison of manganese agent and iron agent

International Nuclear Information System (INIS)

Fujita, Osamu; Hiraishi, Kumiko; Suginobu, Yoshito; Takeuchi, Masayasu; Narabayashi, Isamu

1996-01-01

We investigated and compared signal intensity and the effect of imaging the upper abdomen with blueberry juice (B.J.), a Mn agent utilizing the properties of paramagnetic metals, and FerriSeltz (F.S.), an iron agent. Since the relaxation effect was much stronger with B.J. than with F.S., the signal intensity required of a peroral contrast agent was able to be obtained at a much lower concentration of B.J. In imaging the upper abdomen, B.J. had a positive effect on imaging in T1-weighted images, and a negative effect in T2-weighted images. F.S. had a positive imaging effect in both, and because it showed extremely high signals in T2-weighted images, motion artifact arose. (author)

Blowing the whistle to protect a patient: a comparison between physiotherapy students and physiotherapists.

Science.gov (United States)

Mansbach, Abraham; Melzer, Itzik; Bachner, Yaacov G

2012-12-01

To answer three questions: Are physiotherapists and physiotherapy students willing to take action to prevent misconduct in order to protect a patient's interests? Are they willing to report the misconduct to authorities within an organisation and/or outside of it? Are they willing to report a colleague's wrongdoing as well as that of a manager? Observational questionnaire study. Two hundred and twenty-seven participants divided into two groups: 126 undergraduate students at the Department of Physical Therapy at Ben Gurion University, and 101 certified physiotherapists working in hospitals and rehabilitation centres in south and central regions of Israel. Participants were presented with two vignettes - one describing a colleague's misconduct and the other describing a manager's misconduct - and asked to make a decision about whistleblowing. Both groups rated their own willingness to take action to change the harmful situations very highly. The physiotherapists perceived a colleague's misconduct as being more serious than the students, and were more willing to intervene internally. The students were more prepared than the physiotherapists to take such action externally. The students perceived the manager's misconduct as being more serious than the physiotherapists, and also reported a greater readiness to intervene externally. Physiotherapists consider acts that are detrimental to a patient to be very serious, and are more willing to take action when the offending individual is a colleague. Students are more willing to blow the whistle externally. This article suggests tools for handling similar situations. Copyright © 2011 Chartered Society of Physiotherapy. Published by Elsevier Ltd. All rights reserved.

Topical antifungal agents: an update.

Science.gov (United States)

Diehl, K B

1996-10-01

So many topical antifungal agents have been introduced that it has become very difficult to select the proper agent for a given infection. Nonspecific agents have been available for many years, and they are still effective in many situations. These agents include Whitfield's ointment, Castellani paint, gentian violet, potassium permanganate, undecylenic acid and selenium sulfide. Specific antifungal agents include, among others, the polyenes (nystatin, amphotericin B), the imidazoles (metronidazole, clotrimazole) and the allylamines (terbinafine, naftifine). Although the choice of an antifungal agent should be based on an accurate diagnosis, many clinicians believe that topical miconazole is a relatively effective agent for the treatment of most mycotic infections. Terbinafine and other newer drugs have primary fungicidal effects. Compared with older antifungal agents, these newer drugs can be used in lower concentrations and shorter therapeutic courses. Studies are needed to evaluate the clinical efficacies and cost advantages of both newer and traditional agents.

Interacting agents in finance

NARCIS (Netherlands)

Hommes, C.; Durlauf, S.N.; Blume, L.E.

2008-01-01

Interacting agents in finance represent a behavioural, agent-based approach in which financial markets are viewed as complex adaptive systems consisting of many boundedly rational agents interacting through simple heterogeneous investment strategies, constantly adapting their behaviour in response

Agent-based enterprise integration

Energy Technology Data Exchange (ETDEWEB)

N. M. Berry; C. M. Pancerella

1998-12-01

The authors are developing and deploying software agents in an enterprise information architecture such that the agents manage enterprise resources and facilitate user interaction with these resources. The enterprise agents are built on top of a robust software architecture for data exchange and tool integration across heterogeneous hardware and software. The resulting distributed multi-agent system serves as a method of enhancing enterprises in the following ways: providing users with knowledge about enterprise resources and applications; accessing the dynamically changing enterprise; locating enterprise applications and services; and improving search capabilities for applications and data. Furthermore, agents can access non-agents (i.e., databases and tools) through the enterprise framework. The ultimate target of the effort is the user; they are attempting to increase user productivity in the enterprise. This paper describes their design and early implementation and discusses the planned future work.

Radiopharmaceutical scanning agents

International Nuclear Information System (INIS)

1976-01-01

This invention is directed to dispersions useful in preparing radiopharmaceutical scanning agents, to technetium labelled dispersions, to methods for preparing such dispersions and to their use as scanning agents

Agente adaptable y aprendizaje

Directory of Open Access Journals (Sweden)

Arturo Angel Lara Rivero

2013-05-01

Full Text Available En este trabajo se contrasta el concepto de agente programado con el de agente complejo adaptable, se presenta una nueva visión ligada al aprendizaje y la estructura del agente. La imagen del agente se analiza considerando los modelos internos, la práctica, el concepto de rutina y la influencia en su comportamiento, y la importancia del aprendizaje ex ante y ex post. Por último se muestra que la resolución de problemas está sujeta a restricciones del agente y se describen las formas de explorar el espacio de soluciones mediante tres tipos de exploración: exhaustiva, aleatoria y selectiva.

Three-agent Peer Evaluation

OpenAIRE

Vicki Knoblauch

2008-01-01

I show that every rule for dividing a dollar among three agents impartially (so that each agent's share depends only on her evaluation by her associates) underpays some agent by at least one-third of a dollar for some consistent profile of evaluations. I then produce an impartial division rule that never underpays or overpays any agent by more than one-third of a dollar, and for most consistent evaluation profiles does much better.

Release of the Diclofenac Sodium by Nanofibers of Poly(3-hydroxybutyrate-co-3-hydroxyvalerate Obtained from Electrospinning and Solution Blow Spinning

Directory of Open Access Journals (Sweden)

Michelle Andrade Souza

2014-01-01

Full Text Available Electrospun fibers are explored as a new system for controlled drug delivery. Novel techniques capable of obtaining polymer nanofibers have been reported in the literature. They include solution blow spinning (SBS, which is a technique to produce polymer nanofibers in the same range as electrospinning, using pressurized gas instead of high voltage. The present study investigates release characteristics of diclofenac sodium encapsulated at three concentrations (5, 10, and 20% w/v in poly(3-hydroxybutyrate-co-3-hydroxyvalerate (PHBV nanofibers made by electrospinning and SBS and determines the drug’s effect on fiber morphology and structural properties. PHBV nanofibers were characterized using scanning electronic microscopy, differential scanning calorimetry, and X-ray diffraction, and the release profile was examined via UV-Vis spectrophotometry. Both electrospinning and SBS encapsulated diclofenac sodium in PHBV membranes efficiently and effectively. The profile of the in vitro release of diclofenac sodium was dependent on drug concentration and temperature. The drug reduced crystallinity and increased flexibility.

A Verification Logic for GOAL Agents

Science.gov (United States)

Hindriks, K. V.

Although there has been a growing body of literature on verification of agents programs, it has been difficult to design a verification logic for agent programs that fully characterizes such programs and to connect agent programs to agent theory. The challenge is to define an agent programming language that defines a computational framework but also allows for a logical characterization useful for verification. The agent programming language GOAL has been originally designed to connect agent programming to agent theory and we present additional results here that GOAL agents can be fully represented by a logical theory. GOAL agents can thus be said to execute the corresponding logical theory.

Variations on agent-oriented programming

Directory of Open Access Journals (Sweden)

Dalia Baziukė

2017-12-01

Full Text Available Occurrence of the agent paradigm and its further applications have stimulated the emergence of new concepts and methodologies in computer science. Today terms like multi-agent system, agent-oriented methodology, and agent-oriented programming (AOP are widely used. The aim of this paper is to clarify the validity of usage of the terms AOP and AOP language. This is disclosed in two phases of an analysis process. Determining to which concepts, terms like agent, programming, object-oriented analysis and design, object-oriented programming, and agent-oriented analysis and design correspond is accomplished in the first phase. Analysis of several known agent system engineering methodologies in terms of key concepts used, final resulting artifacts, and their relationship with known programming paradigms and modern tools for agent system development is performed in the second phase. The research shows that in most cases in the final phase of agent system design and in the coding stage, the main artifact is an object, defined according to the rules of the object-oriented paradigm. Hence, we say that the computing society still does not have AOP owing to the lack of an AOP language. Thus, the term AOP is very often incorrectly assigned to agent system development frameworks that in most cases, transform agents into objects.DOI: 10.15181/csat.v5i1.1361

Users, Bystanders and Agents

DEFF Research Database (Denmark)

Krummheuer, Antonia Lina

2015-01-01

Human-agent interaction (HAI), especially in the field of embodied conversational agents (ECA), is mainly construed as dyadic communication between a human user and a virtual agent. This is despite the fact that many application scenarios for future ECAs involve the presence of others. This paper...

Considerations for the Estimation of the Risk of Environmental Contamination Due to Blow Out in Offshore Exploratory Drilling Projects; Consideraciones a la Estimación del Riesgo de Contaminación Ambiental por Blow Out en Proyectos de Perforación de Sondeos Exploratorios Offshore

Energy Technology Data Exchange (ETDEWEB)

Hurtado, A.; Eguilior, S.; Recreo, F.

2015-07-01

From the consideration of a contemporary society based on the need of a high-level complex technology with a high intrinsic level of uncertainty and its relationship with risk assessment, this analysis, conducted in late 2014, was developed from that that led the Secretary of State for the Environment to the Resolution of 29 May 2014, by which the Environmental Impact Statement of the Exploratory Drilling Project in the hydrocarbons research permits called ''Canarias 1-9// was set out and published in the Spanish Official State Gazette number 196 on 13rd August 2014. The aim of the present study is to analyze the suitability with which the worst case associated probability is identified and defined and its relation to the total risk estimate from a blow out. Its interest stems from the fact that all risk management methodologically rests on two pillars, i.e., on a sound risk analysis and evaluation. This determines the selection of management tools in relation to its level of complexity, the project phase and its potential impacts on the health, safety and environmental contamination dimensions.

Dynamic study of ocular movement with MR imaging in orbital blow-out fracture

International Nuclear Information System (INIS)

Aibara, Ryuichi; Kawakita, Seiji; Matsumoto, Yasushi; Sadamoto, Masanori; Yumoto, Eiji.

1996-01-01

Operative indications for orbital blow-out fracture (OBF) remain controversial. One of the major sources of this controversy is that an accurate diagnosis of ocular movement disturbances can not be made by conventional procedures such as the Hess screen test, traction test, or CT scan. Disturbances in ocular movement resulting from OBF can occur not only with entrapment of the extraocular muscle but also with intraorbital bleeding, edema, and/or a variety of other unclear factors. To obtain a more accurate diagnosis and to assist in the choice of treatment, ocular movement was examined using orbital 'cine mode' MR imaging. MR images were obtained in multiple phases of vertical and horizontal ocular movements by using the 'fast SE' capabilities of the SIERRA, GE-YMS MR scanner (1.5 Tesla, superconductive). The fixed eye method was applied to two normal volunteers and to patients with 'pure' OBF. Five marks for binocular fixation were affixed to the inner wall of the gantry: one at the primary position and four at secondary positions. While keeping the subject's eye focused on each of these marks for about 30 sec, MR images (head coil) of the axial view and bilateral oblique sagittal view along the optic nerve were carried out. In the normal volunteers, a good demonstration of smooth movement of the eye ball, extraocular muscles, and the optic nerve could be obtained. In the OBF patients, it was clearly observed that the disturbance in ocular movement was caused by poor extension of the external ocular muscles, specifically the inferior rectus muscle in the orbital floor fracture, and the internal rectus muscle in the medial wall fracture. These observations suggested that dynamic orbital imaging with MR would be extremely valuable in the assessment of disturbances of ocular movement in OBF. (author)

Hyperthermia and chemotherapy agent

International Nuclear Information System (INIS)

Roizin-Towle, L.; Hall, E.J.

1981-01-01

The use of chemotherapeutic agents for the treatment of cancer dates back to the late 19th century, but the modern era of chemotherapy drugs was ushered in during the 1940's with the development of the polyfunctional alkylating agent. Since then, numerous classes of drugs have evolved and the combined use of antineoplastic agents with other treatment modalities such as radiation or heat, remains a large relatively unexplored area. This approach, combining local hyperthermia with chemotherapy agents affords a measure of targeting and selective toxicity not previously available for drugs. In this paper, the effects of adriamycin, bleomycin and cis-platinum are examined. The adjuvant use of heat may also reverse the resistance of hypoxic cells noted for some chemotherapy agents

Reasoning about emotional agents

NARCIS (Netherlands)

Meyer, J.-J.

In this paper we discuss the role of emotions in artificial agent design, and the use of logic in reasoning about the emotional or affective states an agent can reside in. We do so by extending the KARO framework for reasoning about rational agents appropriately. In particular we formalize in

Clustering recommendations to compute agent reputation

Science.gov (United States)

Bedi, Punam; Kaur, Harmeet

2005-03-01

Traditional centralized approaches to security are difficult to apply to multi-agent systems which are used nowadays in e-commerce applications. Developing a notion of trust that is based on the reputation of an agent can provide a softer notion of security that is sufficient for many multi-agent applications. Our paper proposes a mechanism for computing reputation of the trustee agent for use by the trustier agent. The trustier agent computes the reputation based on its own experience as well as the experience the peer agents have with the trustee agents. The trustier agents intentionally interact with the peer agents to get their experience information in the form of recommendations. We have also considered the case of unintentional encounters between the referee agents and the trustee agent, which can be directly between them or indirectly through a set of interacting agents. The clustering is done to filter off the noise in the recommendations in the form of outliers. The trustier agent clusters the recommendations received from referee agents on the basis of the distances between recommendations using the hierarchical agglomerative method. The dendogram hence obtained is cut at the required similarity level which restricts the maximum distance between any two recommendations within a cluster. The cluster with maximum number of elements denotes the views of the majority of recommenders. The center of this cluster represents the reputation of the trustee agent which can be computed using c-means algorithm.

Agents Play Mix-game

Science.gov (United States)

Gou, Chengling

In recent years, economics and finance see the shift of paradigm from representative agent models to heterogeneous agent models [1, 2]. More and more economists and physicists made efforts in research on heterogeneous agent models for financial markets. Minority game (MG) proposed by D. Challet, and Y. C. Zhang [3] is an example among such efforts. Challet and Zhang's MG model, together with the original bar model of Arthur, attracts a lot of following studies [4-6]. Given MG's richness and yet underlying simplicity, MG has also received much attention as a financial market model [4]. MG comprises an odd number of agents choosing repeatedly between the options of buying (1) and selling (0) a quantity of a risky asset. The agents continually try to make the minority decision, i.e. buy assets when the majority of other agents are selling, and sell when the majority of other agents are buying. Neil F. Johnson [4, 5] and coworkers extended MG by allowing a variable number of active traders at each timestep— they called their modified game as the Grand Canonical Minority Game (GCMG). GCMG, and to a lesser extent the basic MG itself, can reproduce the stylized facts of financial markets, such as volatility clustering and fat-tail distributions.

Agent planning in AgScala

Science.gov (United States)

Tošić, Saša; Mitrović, Dejan; Ivanović, Mirjana

2013-10-01

Agent-oriented programming languages are designed to simplify the development of software agents, especially those that exhibit complex, intelligent behavior. This paper presents recent improvements of AgScala, an agent-oriented programming language based on Scala. AgScala includes declarative constructs for managing beliefs, actions and goals of intelligent agents. Combined with object-oriented and functional programming paradigms offered by Scala, it aims to be an efficient framework for developing both purely reactive, and more complex, deliberate agents. Instead of the Prolog back-end used initially, the new version of AgScala relies on Agent Planning Package, a more advanced system for automated planning and reasoning.

Multi-Agent Systems for E-Commerce

OpenAIRE

Solodukha, T. V.; Sosnovskiy, O. A.; Zhelezko, B. A.

2009-01-01

The article focuses on multi-agent systems (MAS) and domains that can benefit from multi-agent technology. In the last few years, the agent based modeling (ABM) community has developed several practical agent based modeling toolkits that enable individuals to develop agent-based applications. The comparison of agent-based modeling toolkits is given. Multi-agent systems are designed to handle changing and dynamic business processes. Any organization with complex and distributed business pro...

Producing, Importing, and Exporting Ozone-Depleting Substances

Science.gov (United States)

Overview page provides links to information on producing, importing, and exporting ozone-depleting substances, including information about the HCFC allowance system, importing, labeling, recordkeeping and reporting.

Automatic Generation of Agents using Reusable Soft Computing Code Libraries to develop Multi Agent System for Healthcare

OpenAIRE

Priti Srinivas Sajja

2015-01-01

This paper illustrates architecture for a multi agent system in healthcare domain. The architecture is generic and designed in form of multiple layers. One of the layers of the architecture contains many proactive, co-operative and intelligent agents such as resource management agent, query agent, pattern detection agent and patient management agent. Another layer of the architecture is a collection of libraries to auto-generate code for agents using soft computing techni...

Effectiveness testing of spill-treating agents

International Nuclear Information System (INIS)

Fingas, M.F.; Stoodley, R.; Laroche, N.

1990-01-01

Laboratory effectiveness tests are described for four classes of spill-treating agents: solidifiers, demulsifying agents, surface-washing agents and dispersants. Many treating agents in these four categories have been tested for effectiveness and the results are presented. Solidifiers or gelling agents solidify oil, requiring a large amount of agent to solidify oil-ranging between 16% by weight, to over 200%. Emulsion breakers prevent or reverse the formation of water-in-oil emulsions. A newly-developed effectiveness test shows that only one product is highly effective; however, many products will work, but require large amounts of spill-treating agent. Surfactant--containing materials are of two types, surface-washing agents and dispersants. Testing has shown that an agent that is a good dispersant is conversely a poor surface-washing agent, and vice versa. Tests of surface-washing agents show that only a few agents have effectiveness of 25-40%, where this effectiveness is the percentage of heavy oil removed from a test surface. Results using the 'swirling flask' test for dispersant effectiveness are reported. Heavy oils show effectiveness values of about 1%, medium crudes of about 10%, light crude oils of about 30% and very light oils of about 90%. (author)

BSL-3 laboratory practices in the United States: comparison of select agent and non-select agent facilities.

Science.gov (United States)

Richards, Stephanie L; Pompei, Victoria C; Anderson, Alice

2014-01-01

New construction of biosafety level 3 (BSL-3) laboratories in the United States has increased in the past decade to facilitate research on potential bioterrorism agents. The Centers for Disease Control and Prevention inspect BSL-3 facilities and review commissioning documentation, but no single agency has oversight over all BSL-3 facilities. This article explores the extent to which standard operating procedures in US BSL-3 facilities vary between laboratories with select agent or non-select agent status. Comparisons are made for the following variables: personnel training, decontamination, personal protective equipment (PPE), medical surveillance, security access, laboratory structure and maintenance, funding, and pest management. Facilities working with select agents had more complex training programs and decontamination procedures than non-select agent facilities. Personnel working in select agent laboratories were likely to use powered air purifying respirators, while non-select agent laboratories primarily used N95 respirators. More rigorous medical surveillance was carried out in select agent workers (although not required by the select agent program) and a higher level of restrictive access to laboratories was found. Most select agent and non-select agent laboratories reported adequate structural integrity in facilities; however, differences were observed in personnel perception of funding for repairs. Pest management was carried out by select agent personnel more frequently than non-select agent personnel. Our findings support the need to promote high quality biosafety training and standard operating procedures in both select agent and non-select agent laboratories to improve occupational health and safety.

Agent Persuasion Mechanism of Acquaintance

Science.gov (United States)

Jinghua, Wu; Wenguang, Lu; Hailiang, Meng

Agent persuasion can improve negotiation efficiency in dynamic environment based on its initiative and autonomy, and etc., which is being affected much more by acquaintance. Classification of acquaintance on agent persuasion is illustrated, and the agent persuasion model of acquaintance is also illustrated. Then the concept of agent persuasion degree of acquaintance is given. Finally, relative interactive mechanism is elaborated.

Smart Agents and Sentiment in the Heterogeneous Agent Model

Czech Academy of Sciences Publication Activity Database

Vácha, Lukáš; Baruník, Jozef; Vošvrda, Miloslav

-, č. 81 (2010), s. 39-40 ISSN 0926-4981 R&D Projects: GA ČR(CZ) GA402/09/0965; GA ČR GP402/08/P207 Grant - others:GAUK(CZ) GAUK 46108 Institutional research plan: CEZ:AV0Z10750506 Keywords : Smart traders * price movements * smart traders concept Subject RIV: AH - Economics http://library.utia.cas.cz/separaty/2010/E/vacha- smart agent s and sentiment in the heterogeneous agent model.pdf

10th KES Conference on Agent and Multi-Agent Systems : Technologies and Applications

CERN Document Server

Chen-Burger, Yun-Heh; Howlett, Robert; Jain, Lakhmi

2016-01-01

The modern economy is driven by technologies and knowledge. Digital technologies can free, shift and multiply choices, often intruding on the space of other industries, by providing new ways of conducting business operations and creating values for customers and companies. The topics covered in this volume include software agents, multi-agent systems, agent modelling, mobile and cloud computing, big data analysis, business intelligence, artificial intelligence, social systems, computer embedded systems and nature inspired manufacturing, etc. that contribute to the modern Digital Economy. This volume highlights new trends and challenges in agent, new digital and knowledge economy research and includes 28 papers classified in the following specific topics: business process management, agent-based modeling and simulation, anthropic-oriented computing, learning paradigms, business informatics and gaming, digital economy, and advances in networked virtual enterprises. Published papers were selected for presentatio...

Security Measures to Protect Mobile Agents

Science.gov (United States)

Dadhich, Piyanka; Govil, M. C.; Dutta, Kamlesh

2010-11-01

The security issues of mobile agent systems have embarrassed its widespread implementation. Mobile agents that move around the network are not safe because the remote hosts that accommodate the agents initiates all kinds of attacks. These hosts try to analyze the agent's decision logic and their accumulated data. So, mobile agent security is the most challenging unsolved problems. The paper analyzes various security measures deeply. Security especially the attacks performed by hosts to the visiting mobile agent (the malicious hosts problem) is a major obstacle that prevents mobile agent technology from being widely adopted. Being the running environment for mobile agent, the host has full control over them and could easily perform many kinds of attacks against them.

Mobile agent location in distributed environments

Science.gov (United States)

Fountoukis, S. G.; Argyropoulos, I. P.

2012-12-01

An agent is a small program acting on behalf of a user or an application which plays the role of a user. Artificial intelligence can be encapsulated in agents so that they can be capable of both behaving autonomously and showing an elementary decision ability regarding movement and some specific actions. Therefore they are often called autonomous mobile agents. In a distributed system, they can move themselves from one processing node to another through the interconnecting network infrastructure. Their purpose is to collect useful information and to carry it back to their user. Also, agents are used to start, monitor and stop processes running on the individual interconnected processing nodes of computer cluster systems. An agent has a unique id to discriminate itself from other agents and a current position. The position can be expressed as the address of the processing node which currently hosts the agent. Very often, it is necessary for a user, a processing node or another agent to know the current position of an agent in a distributed system. Several procedures and algorithms have been proposed for the purpose of position location of mobile agents. The most basic of all employs a fixed computing node, which acts as agent position repository, receiving messages from all the moving agents and keeping records of their current positions. The fixed node, responds to position queries and informs users, other nodes and other agents about the position of an agent. Herein, a model is proposed that considers pairs and triples of agents instead of single ones. A location method, which is investigated in this paper, attempts to exploit this model.

The CNEN Helium-Caesium Blow-Down MPD Facility and Experiments with a Prototype Duct

Energy Technology Data Exchange (ETDEWEB)

Bertolini, E.; Toschi, R. [CNEN, Frascati (Italy); Lindley, B. C. [C.A. Parsons and Co. Ltd (United Kingdom); Brown, R.; McNab, I. R. [International Research and Development Co. Ltd., Newcastle Upon Tyne (United Kingdom)

1966-11-15

The CNEN blow-down loop has been designed to study a helium-caesium MPD generator with particular regard to non-equilibrium ionization effects. An operating condition of the loop is: gas mass flow 0.2 kg/sec, seed fraction 1 at, wt.%, useful pulse duration 20 sec, stagnation temperature 2000 Degree-Sign K, stagnation pressure 5 atm abs, thermal power 1.6 MW, Mach number 0.6, magnetic field 4 Wb/m2, total impurity level less than 100 ppm. A sufficiently wide range of the stagnation conditions can be obtained with the present arrangement of the loop (temperature up to 2000*K, pressure from slightly sub-atmospheric to 6atmabs, gas mass flow from 50 g/sec to 400 g/sec, seed fraction from 0.1 to 2 at. wt.%. The storage heater is an alumina pebble bed electrically heated with tungsten elements and thermally insulated with zirconia fibre; the thermal capacity at 2000 Degree-Sign K is about 1000 MJ. Pure helium is obtained by evaporation of liquid helium at between 4.5 and 5 Degree-Sign K; liquid caesium is injected into a limited section of the pebble bed to provide a mixture of the two gases uniform in density and temperature. The duct is made of boron nitride (5 cm x 3 cm x 22 cm) with 25 pairs of tantalum electrodes whose geometry (electrode width 3 mm, segmentation pitch 9 mm) should prevent current leakage between adjacent electrodes; the duct walls and transfer can be pre-heated up to 1700 Degree-Sign K. A magnetic field of 4 Wb/m{sup 2} is obtained with a pulsed cryogenic magnet with pulse duration of 6 sec. Two series of experiments have been completed to assess the feasibility of the helium-caesium heating system and the generator duct. Heating system experiments, (a) Compatibility of alumina with tungsten, tantalum and caesium, with thermal cycling at 2000 Degree-Sign K; (b) Purification of zirconia fibre and its behaviour at high temperature, with thermal cycling at 2000 Degree-Sign K; (c) Capability of an alumina pebble bed of evaporating, heating and mixing

Stabilized radiographic scanning agents

International Nuclear Information System (INIS)

Fawzi, M.B.

1982-01-01

Stable compositions useful as technetium 99m-based scintigraphic agents comprise gentisic acid or a pharmaceutically-acceptable salt or ester thereof in combination with a pertechnetate reducing agent or dissolved in pertechnetate-99m (sup(99m)TcOsub(4)sup(-)) solution. The compositions are especially useful in combination with a phosphate or phosphonate material that carries the radionuclide to bone, thus providing a skeletal imaging agent

Cellular morphology of organic-inorganic hybrid foams based on alkali alumino-silicate matrix

Science.gov (United States)

Verdolotti, Letizia; Liguori, Barbara; Capasso, Ilaria; Caputo, Domenico; Lavorgna, Marino; Iannace, Salvatore

2014-05-01

Organic-inorganic hybrid foams based on an alkali alumino-silicate matrix were prepared by using different foaming methods. Initially, the synthesis of an inorganic matrix by using aluminosilicate particles, activated through a sodium silicate solution, was performed at room temperature. Subsequently the viscous paste was foamed by using three different methods. In the first method, gaseous hydrogen produced by the oxidization of Si powder in an alkaline media, was used as blowing agent to generate gas bubbles in the paste. In the second method, the porous structure was generated by mixing the paste with a "meringue" type of foam previously prepared by whipping, under vigorous stirring, a water solution containing vegetal proteins as surfactants. In the third method, a combination of these two methods was employed. The foamed systems were consolidated for 24 hours at 40°C and then characterized by FTIR, X-Ray diffraction, scanning electron microscopy (SEM) and compression tests. Low density foams (˜500 Kg/m3) with good cellular structure and mechanical properties were obtained by combining the "meringue" approach with the use of the chemical blowing agent based on Si.

Radiographic scintiscanning agent

International Nuclear Information System (INIS)

Bevan, J.A.

1979-01-01

A new technetium-based scintiscanning agent has been prepared comprising a water soluble sup(99m)Tc-methanehydroxydiphosphonate in combination with a reducing agent selected from stannous, ferrous, chromous and titanous salts. As an additional stabilizer salts and esters of gentisic or ascorbic acids have been used. (E.G.)

Agent-Based Optimization

CERN Document Server

Jędrzejowicz, Piotr; Kacprzyk, Janusz

2013-01-01

This volume presents a collection of original research works by leading specialists focusing on novel and promising approaches in which the multi-agent system paradigm is used to support, enhance or replace traditional approaches to solving difficult optimization problems. The editors have invited several well-known specialists to present their solutions, tools, and models falling under the common denominator of the agent-based optimization. The book consists of eight chapters covering examples of application of the multi-agent paradigm and respective customized tools to solve  difficult optimization problems arising in different areas such as machine learning, scheduling, transportation and, more generally, distributed and cooperative problem solving.

2015 Special Sessions of the 13th International Conference on Practical Applications of Agents and Multi-Agent Systems

CERN Document Server

Hernández, Josefa; Mathieu, Philippe; Campbell, Andrew; Fernández-Caballero, Antonio; Moreno, María; Julián, Vicente; Alonso-Betanzos, Amparo; Jiménez-López, María; Botti, Vicente; Trends in Practical Applications of Agents, Multi-Agent Systems and Sustainability : the PAAMS Collection

2015-01-01

This volume presents the papers that have been accepted for the 2015 special sessions of the 13th International Conference on Practical Applications of Agents and Multi-Agent Systems, held at University of Salamanca, Spain, at 3rd-5th June, 2015: Agents Behaviours and Artificial Markets (ABAM); Agents and Mobile Devices (AM); Multi-Agent Systems and Ambient Intelligence (MASMAI); Web Mining and Recommender systems (WebMiRes); Learning, Agents and Formal Languages (LAFLang); Agent-based Modeling of Sustainable Behavior and Green Economies (AMSBGE); Emotional Software Agents (SSESA) and Intelligent Educational Systems (SSIES). The volume also includes the paper accepted for the Doctoral Consortium in PAAMS 2015. PAAMS, the International Conference on Practical Applications of Agents and Multi-Agent Systems is an evolution of the International Workshop on Practical Applications of Agents and Multi-Agent Systems. PAAMS is an international yearly tribune to present, to discuss, and to disseminate the latest develo...

Agent independent task planning

Science.gov (United States)

Davis, William S.

1990-01-01

Agent-Independent Planning is a technique that allows the construction of activity plans without regard to the agent that will perform them. Once generated, a plan is then validated and translated into instructions for a particular agent, whether a robot, crewmember, or software-based control system. Because Space Station Freedom (SSF) is planned for orbital operations for approximately thirty years, it will almost certainly experience numerous enhancements and upgrades, including upgrades in robotic manipulators. Agent-Independent Planning provides the capability to construct plans for SSF operations, independent of specific robotic systems, by combining techniques of object oriented modeling, nonlinear planning and temporal logic. Since a plan is validated using the physical and functional models of a particular agent, new robotic systems can be developed and integrated with existing operations in a robust manner. This technique also provides the capability to generate plans for crewmembers with varying skill levels, and later apply these same plans to more sophisticated robotic manipulators made available by evolutions in technology.

A Framework for Organization-Aware Agents

DEFF Research Database (Denmark)

Jensen, Andreas Schmidt; Dignum, Virginia; Villadsen, Jørgen

2016-01-01

This short paper introduces and summarizes the AORTA reasoning framework that can be integrated into BDI-agents to enable organizational decision-making. This work has recently been published in the Journal of Autonomous Agents and Multi-Agent Systems (JAAMAS), as [3].......This short paper introduces and summarizes the AORTA reasoning framework that can be integrated into BDI-agents to enable organizational decision-making. This work has recently been published in the Journal of Autonomous Agents and Multi-Agent Systems (JAAMAS), as [3]....

A Comparison of Organization-Centered and Agent-Centered Multi-Agent Systems

DEFF Research Database (Denmark)

Jensen, Andreas Schmidt; Villadsen, Jørgen

2013-01-01

Whereas most classical multi-agent systems have the agent in center, there has recently been a development towards focusing more on the organization of the system, thereby allowing the designer to focus on what the system goals are, without considering how the goals should be fulfilled. We have d...

Contrast agents for MRI

International Nuclear Information System (INIS)

Bonnemain, B.

1994-01-01

Contrast agents MRI (Magnetic Resonance Imaging) have been developed to improve the diagnostic information obtained by this technic. They mainly interact on T1 and T2 parameters and increase consequently normal to abnormal tissues contrast. The paramagnetic agents which mainly act on longitudinal relaxation rate (T1) are gadolinium complexes for which stability is the main parameter to avoid any release of free gadolinium. The superparamagnetic agents that decrease signal intensity by an effect on transversal relaxation rate (T2) are developed for liver, digestive and lymph node imaging. Many area of research are now opened for optimal use of present and future contrast agents in MRI. (author). 28 refs., 4 tabs

Study of Crossling Agent and Couplink Agent Synergism on Mechanical Properties of HDPE-Cu Composites

International Nuclear Information System (INIS)

Mashuri; Sujud, A.A.; Karo Karo, Aloma

2001-01-01

The effects of crosslink agents, coupling agents and synergism on mechanical properties of HDPE-Cu composites materials has been investigated. The crosslink was made with dicumyl peroxide as crosslink agents of 2% concentration, so the interface adhesion of matrix-filler was made with 3-amino propyl triethoxysilane as coupling agents of 0.5% concentration. The results of research's showed, that the crosslink and interface adhesion of matrix-filler can increase tensile strength and elongation at break of HDPE-Cu composites. The synergism of two agents can increase tensile strength to 20% and elongation at break to 23% of HDPE-Cu composites materials

Overview of shoreline cleaning agents

International Nuclear Information System (INIS)

Clayton, J.

1992-01-01

Chemical cleaning agents may be used to promote release of stranded oil from shorelines for reasons including biological sensitivity of indigenous fauna and flora to the oil, amenity considerations of the shoreline, or concern about refloating of the oil and subsequent stranding on adjacent shorelines. While use of chemical cleaning agents may be appropriate under proper toxic responses in circumstances, certain limitations should be recognized. The potential for toxic responses in indigenous fauna and flora to the cleaning agents must be considered. Enhanced penetration of oil into permeable shorelines following treatment with chemical cleaning agents also is not desirable. However, if conditions related to toxicity and substrate permeability are determined to be acceptable, the use of chemical cleaning agents for treatment of stranded oil can be considered. Chemical agents for cleaning oiled shorelines can be grouped into three categories: (1) non-surfactant-based solvents, (2) chemical dispersants, and (3) formulations especially designed to release stranded oil from shoreline substrates (i.e., shoreline-cleaning-agents). Depending on the specific circumstances present on an oiled shoreline, it is generally desirable that chemical agents used for cleaning will release oil from shoreline substrate(s) to surface waters. Recovery of the oil can then be accomplished by mechanical procedures such as booming and skimming operations

Radiographic scanning agent

International Nuclear Information System (INIS)

Tofe, A.J.

1976-01-01

A stable radiographic scanning agent on a sup(99m)Tc basis has been developed. The substance contains a pertechnetate reduction agent, tin(II)-chloride, chromium(II)-chloride, or iron(II)-sulphate, as well as an organospecific carrier and ascorbic acid or a pharmacologically admissible salt or ester of ascorbic acid. (VJ) [de