WE-G-BRA-06: Application of Systems and Control Theory-Based Hazard Analysis to Radiotherapy

Energy Technology Data Exchange (ETDEWEB)

Pawlicki, T [UC San Diego, La Jolla, CA (United States); Samost, A; Leveson, N [Massachusetts Institute of Technology, Cambridge, MA (United States)

2015-06-15

Purpose: The process of delivering radiation occurs in a complex socio-technical system heavily reliant on human operators. Furthermore, both humans and software are notoriously challenging to account for in traditional hazard analysis models. High reliability industries such as aviation have approached this problem through using hazard analysis techniques grounded in systems and control theory. The purpose of this work is to apply the Systems Theoretic Accident Model Processes (STAMP) hazard model to radiotherapy. In particular, the System-Theoretic Process Analysis (STPA) approach is used to perform a hazard analysis of a proposed on-line adaptive cranial radiosurgery procedure that omits the CT Simulation step and uses only CBCT for planning, localization, and treatment. Methods: The STPA procedure first requires the definition of high-level accidents and hazards leading to those accidents. From there, hierarchical control structures were created followed by the identification and description of control actions for each control structure. Utilizing these control structures, unsafe states of each control action were created. Scenarios contributing to unsafe control action states were then identified and translated into system requirements to constrain process behavior within safe boundaries. Results: Ten control structures were created for this new CBCT-only process which covered the areas of hospital and department management, treatment design and delivery, and vendor service. Twenty three control actions were identified that contributed to over 80 unsafe states of those control actions resulting in over 220 failure scenarios. Conclusion: The interaction of people, hardware, and software are highlighted through the STPA approach. STPA provides a hierarchical model for understanding the role of management decisions in impacting system safety so that a process design requirement can be traced back to the hazard and accident that it is intended to mitigate. Varian

An overview of the hazardous waste remedial actions program: hazardous and mixed waste activities for the U.S. Departments of energy and defense

International Nuclear Information System (INIS)

Craig, Robert B.; Rothermich, Nancy E.

1991-01-01

In May 1987 all mixed waste generated at the U.S. Department of Energy (DOE) facilities became jointly regulated by the U.S. Environmental Protection Agency (EPA) and DOE. The Department of Defense (DOD) generates hazardous wastes and is also regulated by the EPA. To maintain or attain compliance, both DOE and DOD have initiated compliance activities on all hazardous and mixed waste streams. This compliance includes the development of innovative technologies and processes to avoid the generation of hazardous and mixed wastes, development of technologies to treat the process wastes that are unavoidably generated, development of technologies to restore the environment where wastes have been released to the environment, the cleanup of asbestos and the monitoring of radon in federal facilities, the completion of remedial investigation/feasibility studies, and development of the data systems that are necessary to compile this information. This paper will describe each of these activities as they relate to compliance with the Resource Conservation and Recovery Act and/or CERCLA and their implementing regulations

Prevention and control of hazards in seafood

DEFF Research Database (Denmark)

Huss, Hans Henrik; Reilly, A.; Embarek, Peter Karim Ben

2000-01-01

-harvest and are difficult or impossible to control by applying presently available preventive measures. In contrast, the hazards related to contamination, recontamination or survival of biological hazards during processing are well-defined and can be controlled by applying Good Manufacturing Practice (GMP), Good Hygiene......Seafood is high on the list of foods transmitting disease. However, the food safety issues are highly focussed and more than 80% of all seafood-borne outbreaks are related to biotoxins (ciguatoxin), scombrotoxin or the consumption of raw molluscan shellfish. The safety hazards in seafood production...

Example process hazard analysis of a Department of Energy water chlorination process

Energy Technology Data Exchange (ETDEWEB)

1993-09-01

On February 24, 1992, the Occupational Safety and Health Administration (OSHA) released a revised version of Section 29 Code of Federal Regulations CFR Part 1910 that added Section 1910.119, entitled ``Process Safety Management of Highly Hazardous Chemicals`` (the PSM Rule). Because US Department of Energy (DOE) Orders 5480.4 and 5483.1A prescribe OSHA 29 CFR 1910 as a standard in DOE, the PSM Rule is mandatory in the DOE complex. A major element in the PSM Rule is the process hazard analysis (PrHA), which is required for all chemical processes covered by the PSM Rule. The PrHA element of the PSM Rule requires the selection and application of appropriate hazard analysis methods to systematically identify hazards and potential accident scenarios associated with processes involving highly hazardous chemicals (HHCs). The analysis in this report is an example PrHA performed to meet the requirements of the PSM Rule. The PrHA method used in this example is the hazard and operability (HAZOP) study, and the process studied is the new Hanford 300-Area Water Treatment Facility chlorination process, which is currently in the design stage. The HAZOP study was conducted on May 18--21, 1993, by a team from the Westinghouse Hanford Company (WHC), Battelle-Columbus, the DOE, and Pacific Northwest Laboratory (PNL). The chlorination process was chosen as the example process because it is common to many DOE sites, and because quantities of chlorine at those sites generally exceed the OSHA threshold quantities (TQs).

Loss experience from natural phenomena hazards in the Department of Energy (50 years of natural phenomena hazard losses)

International Nuclear Information System (INIS)

Hill, J.R.

1993-01-01

This paper presents a historical prespective on losses due to natural hazard incidents (1943-1993) at Department of Energy (DOE) and predecessor agencies including the Atomic Energy Commission (AEC) and the Energy Research and Development Agency (ERDA). This paper also demonstrates how an existing DOE resource can be used to gain valuable insight into injury or property damage incidents. That resource is the Computerized Accident/Incident Reporting System (CAIRS) module of DOE's Safety Performance Measurement System. CAIRS data selected the 1981-1991 DOE injury/illness reports, from all the accident reports of the AEC that cited a natural phenomena hazard as either the direct or indirect cause of the injury/property damage. Specifically, injury or property damage reports were selected for analysis if they had a causal factor link to severe weather or natural phenomena hazard categories. Natural phenomena hazard categories are injury/property damage caused by hurricane/tornado, earthquake, lightning, or flood. Severe weather categories are injury/property damage associated with other than normal weather conditions. The lessons learned, as a result of reviewing case histories, are presented, as are suggestions on how to reduce the likelihood of future injuries/property damage as a result of similar events. A significant finding, is that most injuries and property damage were the result of an indirect causal link to a natural phenomena hazard and thus, may be more preventable than previously thought possible. The primary message, however, is that CAIRS and other incident data bases are valuable resources and should be considered for use by those interested in identifying new ways of protecting the health and safety of the worker and for reducing building losses due to the effects of natural phenomena hazards

Hazardous waste database: Waste management policy implications for the US Department of Energy's Environmental Restoration and Waste Management Programmatic Environmental Impact Statement

International Nuclear Information System (INIS)

Lazaro, M.A.; Policastro, A.J.; Antonopoulos, A.A.; Hartmann, H.M.; Koebnick, B.; Dovel, M.; Stoll, P.W.

1994-01-01

The hazardous waste risk assessment modeling (HaWRAM) database is being developed to analyze the risk from treatment technology operations and potential transportation accidents associated with the hazardous waste management alternatives. These alternatives are being assessed in the Department of Energy's Environmental Restoration and Waste Management Programmatic Environmental Impact Statement (EM PEIS). To support the risk analysis, the current database contains complexwide detailed information on hazardous waste shipments from 45 Department of Energy installations during FY 1992. The database is currently being supplemented with newly acquired data. This enhancement will improve database information on operational hazardous waste generation rates, and the level and type of current on-site treatment at Department of Energy installations

Contingency plan for the Lawrence Livermore National Laboratory's hazardous-waste operations

International Nuclear Information System (INIS)

Roberts, R.S.

1981-01-01

The Lawrence Livermore National Laboratory (LLNL) has the necessary equipment and trained personnel to respond to a large number of hazardous material spills and fires or other emergencies resulting from these spills including injured personnel. This response capability is further expanded by the agreements that LLNL has with a number of outside response agencies. The Hazards Control Department at LLNL functions as the central point for coordinating the response of the equipment and personnel. Emergencies involving hazardous waste are also coordinated through the Hazards Control Department, but the equipment and personnel in the Toxic Waste Control Group would be activated for large volume waste pumpouts. Descriptions of response equipment, hazardous waste locations communication systems, and procedures for personnel involved in the emergency are provided

Design and evaluation guidelines for Department of Energy facilities subjected to natural phenomena hazards

International Nuclear Information System (INIS)

Kennedy, R.P.; Short, S.A.; McDonald, J.R.; McCann, M.W. Jr.; Murray, R.C.; Hill, J.R.

1990-06-01

The Department of Energy (DOE) and the DOE Natural Phenomena Hazards Panel have developed uniform design and evaluation guidelines for protection against natural phenomena hazards at DOE sites throughout the United States. The goal of the guidelines is to assure that DOE facilities can withstand the effects of natural phenomena such as earthquakes, extreme winds, tornadoes, and flooding. The guidelines apply to both new facilities (design) and existing facilities (evaluation, modification, and upgrading). The intended audience is primarily the civil/structural or mechanical engineers conducting the design or evaluation of DOE facilities. The likelihood of occurrence of natural phenomena hazards at each DOE site has been evaluated by the DOE Natural Phenomena Hazard Program. Probabilistic hazard models are available for earthquake, extreme wind/tornado, and flood. Alternatively, site organizations are encouraged to develop site-specific hazard models utilizing the most recent information and techniques available. In this document, performance goals and natural hazard levels are expressed in probabilistic terms, and design and evaluation procedures are presented in deterministic terms. Design/evaluation procedures conform closely to common standard practices so that the procedures will be easily understood by most engineers. Performance goals are expressed in terms of structure or equipment damage to the extent that: (1) the facility cannot function; (2) the facility would need to be replaced; or (3) personnel are endangered. 82 refs., 12 figs., 18 tabs

Design and evaluation guidelines for Department of Energy facilities subjected to natural phenomena hazards

Energy Technology Data Exchange (ETDEWEB)

Kennedy, R.P. (Structural Mechanics Consulting, Inc., Yorba Linda, CA (USA)); Short, S.A. (ABB Impell Corp., Mission Viejo, CA (USA)); McDonald, J.R. (Texas Tech Univ., Lubbock, TX (USA)); McCann, M.W. Jr. (Benjamin (J.R.) and Associates, Inc., Mountain View, CA (USA)); Murray, R.C. (Lawrence Livermore National Lab., CA (USA)); Hill, J.R. (USDOE Assistant Secretary for Environment, Safety, and He

1990-06-01

The Department of Energy (DOE) and the DOE Natural Phenomena Hazards Panel have developed uniform design and evaluation guidelines for protection against natural phenomena hazards at DOE sites throughout the United States. The goal of the guidelines is to assure that DOE facilities can withstand the effects of natural phenomena such as earthquakes, extreme winds, tornadoes, and flooding. The guidelines apply to both new facilities (design) and existing facilities (evaluation, modification, and upgrading). The intended audience is primarily the civil/structural or mechanical engineers conducting the design or evaluation of DOE facilities. The likelihood of occurrence of natural phenomena hazards at each DOE site has been evaluated by the DOE Natural Phenomena Hazard Program. Probabilistic hazard models are available for earthquake, extreme wind/tornado, and flood. Alternatively, site organizations are encouraged to develop site-specific hazard models utilizing the most recent information and techniques available. In this document, performance goals and natural hazard levels are expressed in probabilistic terms, and design and evaluation procedures are presented in deterministic terms. Design/evaluation procedures conform closely to common standard practices so that the procedures will be easily understood by most engineers. Performance goals are expressed in terms of structure or equipment damage to the extent that: (1) the facility cannot function; (2) the facility would need to be replaced; or (3) personnel are endangered. 82 refs., 12 figs., 18 tabs.

Technological options for management of hazardous wastes from US Department of Energy facilities

Energy Technology Data Exchange (ETDEWEB)

Chiu, S.; Newsom, D.; Barisas, S.; Humphrey, J.; Fradkin, L.; Surles, T.

1982-08-01

This report provides comprehensive information on the technological options for management of hazardous wastes generated at facilities owned or operated by the US Department of Energy (DOE). These facilities annually generate a large quantity of wastes that could be deemed hazardous under the Resource Conservation and Recovery Act (RCRA). Included in these wastes are liquids or solids containing polychlorinated biphenyls, pesticides, heavy metals, waste oils, spent solvents, acids, bases, carcinogens, and numerous other pollutants. Some of these wastes consist of nonnuclear hazardous chemicals; others are mixed wastes containing radioactive materials and hazardous chemicals. Nearly 20 unit processes and disposal methods are presented in this report. They were selected on the basis of their proven utility in waste management and potential applicability at DOE sites. These technological options fall into five categories: physical processes, chemical processes, waste exchange, fixation, and ultimate disposal. The options can be employed for either resource recovery, waste detoxification, volume reduction, or perpetual storage. Detailed descriptions of each technological option are presented, including information on process performance, cost, energy and environmental considerations, waste management of applications, and potential applications at DOE sites. 131 references, 25 figures, 23 tables.

Technological options for management of hazardous wastes from US Department of Energy facilities

International Nuclear Information System (INIS)

Chiu, S.; Newsom, D.; Barisas, S.; Humphrey, J.; Fradkin, L.; Surles, T.

1982-08-01

This report provides comprehensive information on the technological options for management of hazardous wastes generated at facilities owned or operated by the US Department of Energy (DOE). These facilities annually generate a large quantity of wastes that could be deemed hazardous under the Resource Conservation and Recovery Act (RCRA). Included in these wastes are liquids or solids containing polychlorinated biphenyls, pesticides, heavy metals, waste oils, spent solvents, acids, bases, carcinogens, and numerous other pollutants. Some of these wastes consist of nonnuclear hazardous chemicals; others are mixed wastes containing radioactive materials and hazardous chemicals. Nearly 20 unit processes and disposal methods are presented in this report. They were selected on the basis of their proven utility in waste management and potential applicability at DOE sites. These technological options fall into five categories: physical processes, chemical processes, waste exchange, fixation, and ultimate disposal. The options can be employed for either resource recovery, waste detoxification, volume reduction, or perpetual storage. Detailed descriptions of each technological option are presented, including information on process performance, cost, energy and environmental considerations, waste management of applications, and potential applications at DOE sites. 131 references, 25 figures, 23 tables

Hazard Analysis Database Report

Energy Technology Data Exchange (ETDEWEB)

GAULT, G.W.

1999-10-13

The Hazard Analysis Database was developed in conjunction with the hazard analysis activities conducted in accordance with DOE-STD-3009-94, Preparation Guide for US Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports, for the Tank Waste Remediation System (TWRS) Final Safety Analysis Report (FSAR). The FSAR is part of the approved TWRS Authorization Basis (AB). This document describes, identifies, and defines the contents and structure of the TWRS FSAR Hazard Analysis Database and documents the configuration control changes made to the database. The TWRS Hazard Analysis Database contains the collection of information generated during the initial hazard evaluations and the subsequent hazard and accident analysis activities. The database supports the preparation of Chapters 3,4, and 5 of the TWRS FSAR and the USQ process and consists of two major, interrelated data sets: (1) Hazard Evaluation Database--Data from the results of the hazard evaluations; and (2) Hazard Topography Database--Data from the system familiarization and hazard identification.

Regulation and Control of Hazardous Wastes

OpenAIRE

Hans W. Gottinger

1994-01-01

Hazardous waste regulations require disposal in approved dumpsites, where environmental consequences are minimal but entry may be privately very costly. Imperfect policing of regulations makes the socially more costly option illicit disposal preferable form the perspective of the private decision maker. The existence of the waste disposal decision, its economic nature, production independence, and the control over environmental damage are key issues in the economics of hazardous waste managem...

Effective tree hazard control on forested recreation sites...losses and protection costs evaluated

Science.gov (United States)

Lee A. Paine

1967-01-01

Effectiveness of hazard control was evaluated by analyzing data on tree failures, accidents, and control costs on California recreation sites. Results indicate that reduction of limb hazard in oaks and bole hazard in conifers is the most effective form of control. Least effective is limb hazard reduction in conifers. After hazard control goals or control budgets have...

Control Decisions for Flammable Gas Hazards in Double Contained Receiver Tanks (DCRTs)

Energy Technology Data Exchange (ETDEWEB)

KRIPPS, L.J.

2000-06-28

This report describes the control decisions for flammable gas hazards in double-contained receiver tanks (DCRTs) made at control decision meetings on November 16, 17, and 18, 1999, on April 19,2000, and on May 10,2000, and their basis. These control decisions, and the analyses that support them, will be documented in an amendment to the Final Safety Analysis Report (FSAR) (CHG 2000a) and Technical Safety Requirements (TSR) (CHG 2000b) to close the Flammable Gas Unreviewed Safety Question (USQ) (Bacon 1996 and Wagoner 1996) for DCRTs. Following the contractor Tier I review of the FSAR and TSR amendment, it will be submitted to the U.S. Department of Energy (DOE), Office of River Protection (ORP) for review and approval.

Hazard Analysis Database Report

CERN Document Server

Grams, W H

2000-01-01

The Hazard Analysis Database was developed in conjunction with the hazard analysis activities conducted in accordance with DOE-STD-3009-94, Preparation Guide for U S . Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports, for HNF-SD-WM-SAR-067, Tank Farms Final Safety Analysis Report (FSAR). The FSAR is part of the approved Authorization Basis (AB) for the River Protection Project (RPP). This document describes, identifies, and defines the contents and structure of the Tank Farms FSAR Hazard Analysis Database and documents the configuration control changes made to the database. The Hazard Analysis Database contains the collection of information generated during the initial hazard evaluations and the subsequent hazard and accident analysis activities. The Hazard Analysis Database supports the preparation of Chapters 3 ,4 , and 5 of the Tank Farms FSAR and the Unreviewed Safety Question (USQ) process and consists of two major, interrelated data sets: (1) Hazard Analysis Database: Data from t...

Control of uranium hazards - Portsmouth uranium enrichment plant

International Nuclear Information System (INIS)

Wagner, E.R.

1985-01-01

This report summarizes the Environmental, Safety and Health programs to control uranium hazards at the Portsmouth Gaseous Diffusion Plant. A description of the physical plant, the facility processes and the attendant uranium flows and effluents are provided. The hazards of uranium are discussed and the control systems are outlined. Finally, the monitoring programs are described and summaries of recent data are provided. 11 figs., 20 tabs

Automated hazard analysis of digital control systems

International Nuclear Information System (INIS)

Garrett, Chris J.; Apostolakis, George E.

2002-01-01

Digital instrumentation and control (I and C) systems can provide important benefits in many safety-critical applications, but they can also introduce potential new failure modes that can affect safety. Unlike electro-mechanical systems, whose failure modes are fairly well understood and which can often be built to fail in a particular way, software errors are very unpredictable. There is virtually no nontrivial software that will function as expected under all conditions. Consequently, there is a great deal of concern about whether there is a sufficient basis on which to resolve questions about safety. In this paper, an approach for validating the safety requirements of digital I and C systems is developed which uses the Dynamic Flowgraph Methodology to conduct automated hazard analyses. The prime implicants of these analyses can be used to identify unknown system hazards, prioritize the disposition of known system hazards, and guide lower-level design decisions to either eliminate or mitigate known hazards. In a case study involving a space-based reactor control system, the method succeeded in identifying an unknown failure mechanism

Application of United States Department of Transportation regulations to hazardous material and waste shipments on the Hanford site

International Nuclear Information System (INIS)

Burnside, M.E.

1992-01-01

All hazardous material and waste transported over roadways open to the public must be in compliance with the U.S. Department of Transportation (DOT) regulations. The DOT states that the hazardous material regulations (HMR) also apply to government-owned, contractor-operated (GOCO) transportation operations over any U.S. Department of Energy (DOE) site roadway where the public has free and unrestricted access. Hazardous material and waste in packages that do not meet DOT regulations must be transported on DOE site roadways in a manner that excludes the public and nonessential workers. At the DOE Richland Field Office (the Hanford Site), hazardous material and waste movements that do not meet DOT requirements are transported over public access roadways during off-peak hours with the roadways barricaded. These movements are accomplished using a transportation plan that involves the DOE, DOE contractors, and private utilities who operate on or near the Hanford Site. This method, which is used at the Hanford Site to comply with DOT regulations onsite, can be communicated to other DOE sites to provide a basis for achieving consistency in similar transportation operations. (author)

Development of hazard analysis by critical control points (HACCP) procedures to control organic chemical hazards in the agricultural production of raw food commodities.

Science.gov (United States)

Ropkins, Karl; Ferguson, Andrew; Beck, Angus J

2003-01-01

Hazard Analysis by Critical Control Points (HACCP) is a systematic approach to the identification, assessment, and control of hazards in the food chain. Effective HACCP requires the consideration of all chemical microbiological, and physical hazards. However, current procedures focus primarily on microbiological and physical hazards, while chemical aspects of HACCP have received relatively little attention. In this article we discuss the application of HACCP to organic chemical contaminants and the problems that are likely to be encountered in agriculture. We also present generic templates for the development of organic chemical contaminant HACCP procedures for selected raw food commodities, that is, cereal crops,raw meats, and milk.

Transportation of Hazardous Materials Emergency Preparedness Hazards Assessment

Energy Technology Data Exchange (ETDEWEB)

Blanchard, A.

2000-02-28

This report documents the Emergency Preparedness Hazards Assessment (EPHA) for the Transportation of Hazardous Materials (THM) at the Department of Energy (DOE) Savannah River Site (SRS). This hazards assessment is intended to identify and analyze those transportation hazards significant enough to warrant consideration in the SRS Emergency Management Program.

Transportation of Hazardous Materials Emergency Preparedness Hazards Assessment

International Nuclear Information System (INIS)

Blanchard, A.

2000-01-01

This report documents the Emergency Preparedness Hazards Assessment (EPHA) for the Transportation of Hazardous Materials (THM) at the Department of Energy (DOE) Savannah River Site (SRS). This hazards assessment is intended to identify and analyze those transportation hazards significant enough to warrant consideration in the SRS Emergency Management Program

Transportation of hazardous materials emergency preparedness hazards assessment

International Nuclear Information System (INIS)

Blanchard, A.

2000-01-01

This report documents the Emergency Preparedness Hazards Assessment (EPHA) for the Transportation of Hazardous Materials (THM) at the Department of Energy (DOE) Savannah River Site (SRS). This hazards assessment is intended to identify and analyze those transportation hazards significant enough to warrant consideration in the SRS Emergency Management Program

Hazard analysis and critical control point (HACCP) for an ultrasound food processing operation.

Science.gov (United States)

Chemat, Farid; Hoarau, Nicolas

2004-05-01

Emerging technologies, such as ultrasound (US), used for food and drink production often cause hazards for product safety. Classical quality control methods are inadequate to control these hazards. Hazard analysis of critical control points (HACCP) is the most secure and cost-effective method for controlling possible product contamination or cross-contamination, due to physical or chemical hazard during production. The following case study on the application of HACCP to an US food-processing operation demonstrates how the hazards at the critical control points of the process are effectively controlled through the implementation of HACCP.

Development of constrained motion control for robot handling of hazardous waste

International Nuclear Information System (INIS)

Starr, G.P.

1993-01-01

Handling and archiving of hazardous waste is an area where automation and robotics can be of significant benefit, by removing the human operator from the workplace and its associated hazards. For reasons of safety, throughput, and reduced setup time, force-controlled robots are well-suited for hazardous materials handling. The focus of this investigation is the development of advanced force control techniques for commercial industrial robots in the surface sampling of hazardous waste containers. Two particular control strategies are considered, (1) preview control, and (2) adaptive control. Preview control uses a sensor which can ''look ahead'' and thereby reduce the effect of surface irregularity on contact force control. Adaptive control allows the robot controller to compensate for changes in the robot characteristics as it changes position, and likewise improves performance. The resulting control algorithms will be applied to a two-dimensional contour-following task using a PUMA robot at the Robotics Research Laboratory at The University of New Mexico. (author) 9 figs., 13 refs

Performance Analysis: Control of Hazardous Energy

Energy Technology Data Exchange (ETDEWEB)

De Grange, Connie E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Freeman, Jeff W. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Kerr, Christine E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2010-10-06

LLNL experienced 26 occurrences related to the control of hazardous energy from January 1, 2008 through August 2010. These occurrences were 17% of the total number of reported occurrences during this 32-month period. The Performance Analysis and Reporting Section of the Contractor Assurance Office (CAO) routinely analyzes reported occurrences and issues looking for patterns that may indicate changes in LLNL’s performance and early indications of performance trends. It became apparent through these analyses that LLNL might have experienced a change in the control of hazardous energy and that these occurrences should be analyzed in more detail to determine if the perceived change in performance was real, whether that change is significant and if the causes of the occurrences are similar. This report documents the results of this more detailed analysis.

Centers for Disease Control and Prevention (CDC) Radiation Hazard Scale Data Product Review Feedback Report

Energy Technology Data Exchange (ETDEWEB)

Askin, A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Buddemeier, B. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Alai, M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Yu, K. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2017-09-20

In support of the Department of Energy (DOE) National nuclear Security Administration (NNSA) and the Centers for Disease Control and Prevention (CDC), Lawrence Livermore National Laboratory (LLNL) assisted in the development of new data templates for disseminating and communicating FRMAC1 data products using the CDC Radiation Hazard Scale communication tool. To ensure these data products will be useful to stakeholders during a radiological emergency, LLNL facilitated opportunities for product socialization and review.

21 CFR 120.8 - Hazard Analysis and Critical Control Point (HACCP) plan.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Hazard Analysis and Critical Control Point (HACCP... SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION HAZARD ANALYSIS AND CRITICAL CONTROL POINT (HACCP) SYSTEMS General Provisions § 120.8 Hazard Analysis and Critical Control Point (HACCP) plan. (a) HACCP plan. Each...

Supplemental Hazard Analysis and Risk Assessment - Hydrotreater

Energy Technology Data Exchange (ETDEWEB)

Lowry, Peter P. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wagner, Katie A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2015-04-01

A supplemental hazard analysis was conducted and quantitative risk assessment performed in response to an independent review comment received by the Pacific Northwest National Laboratory (PNNL) from the U.S. Department of Energy Pacific Northwest Field Office (PNSO) against the Hydrotreater/Distillation Column Hazard Analysis Report issued in April 2013. The supplemental analysis used the hazardous conditions documented by the previous April 2013 report as a basis. The conditions were screened and grouped for the purpose of identifying whether additional prudent, practical hazard controls could be identified, using a quantitative risk evaluation to assess the adequacy of the controls and establish a lower level of concern for the likelihood of potential serious accidents. Calculations were performed to support conclusions where necessary.

Los Alamos Controlled Air Incinerator for hazardous chemical and mixed radioactive wastes

International Nuclear Information System (INIS)

Vavruska, J.S.; Borduin, L.C.; Hutchins, D.A.; Koenig, R.A.; Warner, C.L.

1986-01-01

The Los Alamos Controlled Air Incinerator (CAI) is currently the only radioactive waste incineration facility in the US permitted to treat polychlorinated biphenyls (PCBs). The CAI was developed in the mid-1970's as a demonstration system for volume reduction of transuranic (TRU) contaminated combustible solid wastes. It has since undergone additions and modifications to accommodate hazardous chemical wastes in response to a need within the Department of Energy (DOE) to treat mixed radioactive/chemical wastes. An overview of these additions which include a liquid feed system, a high intensity liquid injection burner, and an activated carbon adsorption unit is presented here. Also included is a discussion of the procedures required for Toxic Substances Control Act (TSCA) and Resource Conservation and Recovery Act (RCRA) permitting of the CAI

Hazardous Waste Remedial Actions Program requirements for quality control of analytical data

International Nuclear Information System (INIS)

Miller, M.S.; Zolyniak, J.W.

1988-08-01

The Hazardous Waste Remedial Action Program (HAZWRAP) is involved in performing field investigations and sample analysis pursuant to the NCP for the Department of Energy and other federal agencies. The purpose of this document is to specify the requirements for the control of the accuracy, precision and completeness of the samples, and data from the point of collection through analysis. The requirements include data reduction and reporting of the resulting environmentally related data. Because every instance and concern may not be addressed in this document, HAZWRAP subcontractors are encouraged to discuss any questions with the HAZWRAP Project Manager hereafter identified as the Project Manager

Is lead dust within nuclear medicine departments a hazard to pediatric patients?

Science.gov (United States)

Hulbert, Shannon M; Carlson, Katherine A

2009-09-01

Because of the penetrating ability of the radiation used in nuclear medicine, metallic lead is widely used as radiation shielding. However, this shielding may present an insidious health hazard because of the dust that is readily removed from the surfaces of lead objects. The lead dust may become airborne, contaminate floors and other nearby surfaces, and be inadvertently inhaled or ingested by patients. We determined if the quantity of lead dust encountered within nuclear medicine departments exceeded Environmental Protection Agency (EPA) standards. For lead dust quantification, professional lead test kits were used to sample fifteen 1-ft(2) sections of different surfaces within the department. Four samples were collected once per week from each site. The samples were then submitted to a National Lead Laboratory-accredited program for a total lead measurement. Lead contamination (mug/ft(2)) for each of the 60 samples was compared with the EPA standards for lead dust. Lead contamination was present at 6 of the 15 sites, and of 60 samples, 18 exceeded the EPA standard of 50 mug/ft(2). Lead contamination is present within nuclear medicine departments, and corrective measures should be considered when dealing with pediatric patients. A larger series needs to be conducted to confirm these findings.

14 CFR 417.415 - Post-launch and post-flight-attempt hazard controls.

Science.gov (United States)

2010-01-01

...-flight-attempt hazard controls. (a) A launch operator must establish, maintain and perform procedures for... system operation. The flight termination system receivers must remain captured by the command control... launch operator must establish procedural controls for hazards associated with an unsuccessful flight...

Nuclear power hazard control policy

Energy Technology Data Exchange (ETDEWEB)

Chicken, J C

1982-01-01

This study presents an analysis of the factors that appear to have influenced the formation and form of nuclear power hazard control policy in Britain. A simple account is given of the technical nature of nuclear hazards and of the legal and administrative framework that has been constructed to control them. The subsequent analysis concentrates primarily on the influence exerted by social and political factors. Particular attention is directed to those political groups which have developed a special interest in the problems of nuclear power, and to the interplay between organised groupings and public opinion generally. The metamorphosis of these groupings is traced from the origins of the nuclear industry in the Second World War to their prominent role during the Windscale Inquiry. Attention is given to the policy constraint imposed by increased expectations in the form of demands for higher standards of living, and improvements in the quality of the environment. The study is concerned with both policy-making and with policy implementation; with interest articulation as well as with the functioning of formal institutions. The evolution of policy takes place in an atmosphere of keen economic debate and conflicting moral perceptions. A model of the policy-making system is postulated.

Nuclear power hazard control policy

International Nuclear Information System (INIS)

Chicken, J.C.

1982-01-01

This study presents an analysis of the factors that appear to have influenced the formation and form of nuclear power hazard control policy in Britain. A simple account is given of the technical nature of nuclear hazards and of the legal and administrative framework that has been constructed to control them. The subsequent analysis concentrates primarily on the influence exerted by social and political factors. Particular attention is directed to those political groups which have developed a special interest in the problems of nuclear power, and to the interplay between organised groupings and public opinion generally. The metamorphosis of these groupings is traced from the origins of the nuclear industry in the Second World War to their prominent role during the Windscale Inquiry. Attention is given to the policy constraint imposed by increased expectations in the form of demands for higher standards of living, and improvements in the quality of the environment. The study is concerned with both policy-making and with policy implementation; with interest articulation as well as with the functioning of formal institutions. The evolution of policy takes place in an atmosphere of keen economic debate and conflicting moral perceptions. A model of the policy-making system is postulated. (author)

Radiation Hazard control report

International Nuclear Information System (INIS)

Morishima, Hiroshige; Koga, Taeko; Inagaki, Masayo; Miki, Ryota; Aoki, Yutaka; Takiguchi, Chizuko; Hutai, Yasuhiro; Sakamoto, Norihiko; Okazaki, Koji

1992-01-01

The results of radiation control for one year from April, 1991 to March, 1992 in the Atomic Energy Research Institute of Kinki University are reported. As for the persons engaging in radiation-related works as of April, 1991, 57 teachers in the Atomic Energy Research Institute and the Faculties of Science and Engineering, Pharmacology and Agriculture, 17 students of Department of Science and Engineering who utilize the reactor facility for graduation research, and 55 students of Department of Science and Engineering and others as the persons engaging in radiation-related works regarding the law on injury prevention, 129 persons in total became the object of radiation control. The state of operation of the nuclear reactor in fiscal year 1991 was the highest thermal output 1 W, the cumulative thermal output 362.62 Wh, and the total time of operation was 563.27 h. The operation of the neutron generator was carried out for 1.17 h because of the periodic inspection and the trial operation. In personal control, the abnormality due to radiation exposure was not found. The radiation control in laboratories and in fields are reported. (K.I.)

Control of biological hazards in cold smoked salmon production

DEFF Research Database (Denmark)

Huss, Hans Henrik; Embarek, Peter Karim Ben; Jeppesen, V.F.

1995-01-01

An outline of the common processing technology for cold smoked salmon in Denmark is presented. The safety hazards related to pathogenic bacteria, parasites and biogenic amines are discussed with special emphasis on hazards related to Clostridium botulinum and Listeria monocytogenes. Critical...... control points are identified for all hazards except growth of L. monocytogenes. For this reason a limitation of shelf life to three weeks at +5 degrees C far cold smoked vacuum-packed salmon having greater than or equal to 3% water phase salt is recommended...

Hazard analysis and critical control point (HACCP) history and conceptual overview.

Science.gov (United States)

Hulebak, Karen L; Schlosser, Wayne

2002-06-01

The concept of Hazard Analysis and Critical Control Point (HACCP) is a system that enables the production of safe meat and poultry products through the thorough analysis of production processes, identification of all hazards that are likely to occur in the production establishment, the identification of critical points in the process at which these hazards may be introduced into product and therefore should be controlled, the establishment of critical limits for control at those points, the verification of these prescribed steps, and the methods by which the processing establishment and the regulatory authority can monitor how well process control through the HACCP plan is working. The history of the development of HACCP is reviewed, and examples of practical applications of HACCP are described.

Technical basis document for natural event hazards

International Nuclear Information System (INIS)

CARSON, D.M.

2003-01-01

This technical basis document was developed to support the Tank Farms Documented Safety Analysis (DSA), and describes the risk binning process and the technical basis for assigning risk bins for natural event hazards (NEH)-initiated representative accident and associated represented hazardous conditions. The purpose of the risk binning process is to determine the need for safety-significant structures, systems, and components (SSC) and technical safety requirement (TSR)-level controls for a given representative accident or represented hazardous conditions based on an evaluation of the frequency and consequence. Note that the risk binning process is not applied to facility workers, because all facility worker hazardous conditions are considered for safety-significant SSCs and/or TSR-level controls. Determination of the need for safety-class SSCs was performed in accordance with DOE-STD-3009-94, ''Preparation Guide for US Department of Energy Nonreactor Nuclear Facility Documented Safety Analyses'', as described in this report

Hazardous landfill management, control options

International Nuclear Information System (INIS)

Corbin, M.H.; Lederman, P.B.

1982-01-01

The land disposal of hazardous wastes has been a common practice over the last half century. The industrial and environmental communities, as well as the public, have an immediate challenge to control the contaminants that may be released from waste land disposal facilities. At the same time, land disposal continues to be, in many cases, the only available disposal technique that can be utilized in the next five years. Thus, it is extremely important that environmentally sound landfill management and control techniques be utilized, both for inactive and active sites. There are a number of key steps in developing a sound management and control plan. These include problem definition, personnel safety, characterization, evaluation of control options, cost-effectiveness analysis and development of an integrated control plan. A number of control options, including diversion, regrading, sealing, and leachate treatment are available and more cost effective in most cases than waste removal. These and other options, as well as the methodology to develop an integrated control plan, are discussed, together with examples. (Auth.)

Evaluation and control of radon daughter hazards in uranium mines

International Nuclear Information System (INIS)

Holaday, D.A.

1974-11-01

This monograph discusses primarily those health hazards to uranium miners which are produced by exposure to ionizing radiation. Emphasis is placed on the areas of evaluation of exposures to the radioactive gas radon-222 and its short-lived transformation products, and methods of controlling such exposures. A limited discussion of the biological effects of radon and radon daughters is undertaken, and some procedures are given for evaluating hazards created by other common contaminants of mine atmospheres. A large amount of information exists on these topics, some of which is unpublished or is not readily available. While efforts were made to obtain data from all sources, undoubtedly some valuable work was overlooked. The monograph is an endeavor to assemble pertinent information and make it available to those who are concerned with producing uranium at minimal risks. Where they were available, a variety of procedures for evaluating hazards are given, and examples of systems for controlling hazards are included. 154 references

Exploratory Studies Facility Subsurface Fire Hazards Analysis

International Nuclear Information System (INIS)

Logan, Richard C.

2002-01-01

The primary objective of this Fire Hazard Analysis (FHA) is to confirm the requirements for a comprehensive fire and related hazards protection program for the Exploratory Studies Facility (ESF) are sufficient to minimize the potential for: The occurrence of a fire or related event; A fire that causes an unacceptable on-site or off-site release of hazardous or radiological material that will threaten the health and safety of employees, the public or the environment; Vital U.S. Department of Energy (DOE) programs suffering unacceptable interruptions as a result of fire and related hazards; Property losses from a fire and related events exceeding limits established by DOE; and Critical process controls and safety class systems being damaged as a result of a fire and related events

Hazardous waste operational plan for site 300

International Nuclear Information System (INIS)

Roberts, R.S.

1982-01-01

This plan outlines the procedures and operations used at LLNL's Site 300 for the management of the hazardous waste generated. This waste consists primarily of depleted uranium (a by-product of U-235 enrichment), beryllium, small quantities of analytical chemicals, industrial type waste such as solvents, cleaning acids, photographic chemicals, etc., and explosives. This plan details the operations generating this waste, the proper handling of this material and the procedures used to treat or dispose of the hazardous waste. A considerable amount of information found in this plan was extracted from the Site 300 Safety and Operational Manual written by Site 300 Facility personnel and the Hazards Control Department

The role of community participation in the control of bird hazards at ...

African Journals Online (AJOL)

... of measures to prevent bird hazards from occurring. One of the most important methods of bird hazard control involves participation of local communities around the airport. This paper illustrates the different ways in which the airport works with the community to control bird collisions with aircraft at Entebbe International ...

Adaptive control of manipulators handling hazardous waste

International Nuclear Information System (INIS)

Colbaugh, R.; Glass, K.

1994-01-01

This article focuses on developing a robot control system capable of meeting hazardous waste handling application requirements, and presents as a solution an adaptive strategy for controlling the mechanical impedance of kinematically redundant manipulators. The proposed controller is capable of accurate end-effector impedance control and effective redundancy utilization, does not require knowledge of the complex robot dynamic model or parameter values for the robot or the environment, and is implemented without calculation of the robot inverse transformation. Computer simulation results are given for a four degree of freedom redundant robot under adaptive impedance control. These results indicate that the proposed controller is capable of successfully performing important tasks in robotic waste handling applications. (author) 3 figs., 39 refs

Virtual reality and telepresence control of robots used in hazardous environments

International Nuclear Information System (INIS)

Bronisz, L.E.; Pittman, P.C.

1996-01-01

The purpose of this project was to explore the application of teleoperation and telepresence control to robots in hazardous environments at Los Alamos. The primary use of this technology would be in a glove-box type operation potentially allowing operators to work on hazardous materials while being completely removed from the danger of exposure in situations that are difficult to completely automate due to the highly unstructured environments or off-normal conditions. This project focused on determining the most appropriate tools and methods that could be applied in the near future resulting in a reasonably inexpensive working teleoperation or telepresence control system for industrial robots used in the handling of hazardous materials. Several topics had to be addressed to perform this task including input devices, control systems, robot manipulators, and simulation techniques or packages. Much of the work is still in the developmental stage and hardware will follow -- providing a usable tool for glove box robot control

Exploratory Studies Facility Subsurface Fire Hazards Analysis

International Nuclear Information System (INIS)

Kubicek, J. L.

2001-01-01

The primary objective of this Fire Hazard Analysis (FHA) is to confirm the requirements for a comprehensive fire and related hazards protection program for the Exploratory Studies Facility (ESF) are sufficient to minimize the potential for: (1) The occurrence of a fire or related event. (2) A fire that causes an unacceptable on-site or off-site release of hazardous or radiological material that will threaten the health and safety of employees, the public or the environment. (3) Vital US. Department of Energy (DOE) programs suffering unacceptable interruptions as a result of fire and related hazards. (4) Property losses from a fire and related events exceeding limits established by DOE. (5) Critical process controls and safety class systems being damaged as a result of a fire and related events

78 FR 23246 - Underground Injection Control Program; Hazardous Waste Injection Restrictions; Petition for...

Science.gov (United States)

2013-04-18

... ENVIRONMENTAL PROTECTION AGENCY [FRL-9804-8] Underground Injection Control Program; Hazardous Waste Injection Restrictions; Petition for Exemption--Class I Hazardous Waste Injection; BASF... exemption to the land disposal Restrictions, under the 1984 Hazardous and Solid Waste [[Page 23247...

Participatory health impact assessment for the development of local government regulation on hazard control

International Nuclear Information System (INIS)

Inmuong, Uraiwan; Rithmak, Panee; Srisookwatana, Soomol; Traithin, Nathathai; Maisuporn, Pornpun

2011-01-01

The Thai Public Health Act 1992 required the Thai local governments to issue respective regulations to take control of any possible health-hazard related activities, both from commercial and noncommercial sources. Since 1999, there has been centrally decentralized of power to a new form of local government establishment, namely Sub-district Administrative Organization (SAO). The SAO is asmall-scale local governing structure while its legitimate function is for community services, including control of health impact related activities. Most elected SAO administrators and officers are new and less experience with any of public health code of practice, particularly on health-hazard control. This action research attempted to introduce and apply a participatory health impact assessment (HIA) tool for the development of SAO health-hazard control regulation. The study sites were at Ban Meang and Kok See SAOs, Khon Kaen Province, Thailand, while all intervention activities conducted during May 2005-April 2006. A set of cooperative activities between researchers and community representatives were planned and organized by; surveying and identifying place and service base locally causing local environmental health problems, organizing community participatory workshops for drafting and proposing the health-hazard control regulation, and appropriate practices for health-hazard controlling measures. This action research eventually could successfully enable the SAO administrators and officers understanding of local environmental-related health problem, as well as development of imposed health-hazard control regulation for local community.

77 FR 26755 - Underground Injection Control Program; Hazardous Waste Injection Restrictions; Petition for...

Science.gov (United States)

2012-05-07

... ENVIRONMENTAL PROTECTION AGENCY [FRL-9669-6] Underground Injection Control Program; Hazardous Waste Injection Restrictions; Petition for Exemption--Class I Hazardous Waste Injection; Diamond... reissuance of an exemption to the land disposal Restrictions, under the 1984 Hazardous and Solid Waste...

76 FR 55908 - Underground Injection Control Program; Hazardous Waste Injection Restrictions; Petition for...

Science.gov (United States)

2011-09-09

... ENVIRONMENTAL PROTECTION AGENCY [FRL-9461-5] Underground Injection Control Program; Hazardous Waste Injection Restrictions; Petition for Exemption--Class I Hazardous Waste Injection; Great Lakes... of an exemption to the land disposal restrictions, under the 1984 Hazardous and Solid Waste...

76 FR 36129 - Underground Injection Control Program; Hazardous Waste Injection Restrictions; Petition for...

Science.gov (United States)

2011-06-21

... ENVIRONMENTAL PROTECTION AGENCY [FRL-9321-3] Underground Injection Control Program; Hazardous Waste Injection Restrictions; Petition for Exemption--Class I Hazardous Waste Injection; ExxonMobil... disposal Restrictions, under the 1984 Hazardous and Solid Waste Amendments to the Resource Conservation and...

78 FR 42776 - Underground Injection Control Program; Hazardous Waste Injection Restrictions; Petition for...

Science.gov (United States)

2013-07-17

... ENVIRONMENTAL PROTECTION AGENCY [FRL9834-8] Underground Injection Control Program; Hazardous Waste Injection Restrictions; Petition for Exemption--Class I Hazardous Waste Injection; Blanchard Refining... disposal Restrictions, under the 1984 Hazardous and Solid Waste Amendments to the Resource Conservation and...

77 FR 52717 - Underground Injection Control Program; Hazardous Waste Injection Restrictions; Petition for...

Science.gov (United States)

2012-08-30

... ENVIRONMENTAL PROTECTION AGENCY [FRL-9724-1] Underground Injection Control Program; Hazardous Waste Injection Restrictions; Petition for Exemption--Class I Hazardous Waste Injection; Cornerstone... exemption to the land disposal Restrictions, under the 1984 Hazardous and Solid Waste Amendments to the...

76 FR 42125 - Underground Injection Control Program; Hazardous Waste Injection Restrictions; Petition for...

Science.gov (United States)

2011-07-18

... ENVIRONMENTAL PROTECTION AGENCY [FRL-9440-3] Underground Injection Control Program; Hazardous Waste Injection Restrictions; Petition for Exemption--Class I Hazardous Waste Injection; ConocoPhillips... Restrictions, under the 1984 Hazardous and Solid Waste Amendments to the Resource Conservation and Recovery Act...

78 FR 76294 - Underground Injection Control Program; Hazardous Waste Injection Restrictions; Petition for...

Science.gov (United States)

2013-12-17

... ENVIRONMENTAL PROTECTION AGENCY [FRL-9904-21-OW] Underground Injection Control Program; Hazardous Waste Injection Restrictions; Petition for Exemption--Class I Hazardous Waste Injection; Mosaic... Restrictions, under the 1984 Hazardous and Solid Waste Amendments to the Resource Conservation and Recovery Act...

75 FR 60457 - Underground Injection Control Program Hazardous Waste Injection Restrictions; Petition for...

Science.gov (United States)

2010-09-30

... ENVIRONMENTAL PROTECTION AGENCY [FRL-9208-4] Underground Injection Control Program Hazardous Waste Injection Restrictions; Petition for Exemption--Class I Hazardous Waste Injection Dow Chemical Company (DOW... 1984 Hazardous and Solid Waste Amendments to the Resource Conservation and Recovery Act have been...

Automated accountability of hazardous materials at AlliedSignal Inc., Kansas City Division

International Nuclear Information System (INIS)

Depew, P.L.

1993-12-01

The Department of Energy's (DOE) Kansas City Plant (KCP), currently operated by AlliedSignal Inc. has developed a comprehensive Hazardous Material Information System (HMIS). The purpose of this system is to provide a practical and automated method to collect, analyze and distribute hazardous material information to DOE, KCP associates, and regulatory agencies. The drivers of the HMIS are compliance with OSHA Hazard Communications, SARA reporting, pollution prevention, waste minimization, control and tracking of hazards, and emergency response. This report provides a discussion of this system

Beryllium. Health hazards and their control. Pt. 2

International Nuclear Information System (INIS)

Lires, O.A.; Delfino, C.A.; Botbol, J.

1991-01-01

In this work (continuation of 'Beryllium' series) health hazards, toxic effects, limits of permissible atmospheric contamination and safe exposure to beryllium are described. Guidelines to the design, control operations and hygienic precautions of the working facilities are given. (Author) [es

Internal Controlling of a Radiology Department.

Science.gov (United States)

Frewer, W; Busch, H P

2015-11-01

Caused by legal reform initiatives there is a continuous need to increase effectiveness and efficiency in hospitals and surgeries, and thus to improve processes.Consequently the successful management of radiological departments and surgeries requires suitable structures and optimization processes to make optimization in the fields of medical quality, service quality and efficiency possible.In future in the DRG System it is necessary that the organisation of processes must focus on the whole clinical treatment of the patients (Clinical Pathways). Therefore the functions of controlling must be more established and adjusted. On the basis of select Controlling instruments like budgeting, performance indicators, process optimization, staff controlling and benchmarking the target-based and efficient control of radiological surgeries and departments is shown. © Georg Thieme Verlag KG Stuttgart · New York.

Part I: Hazard, sensorial and economic implications of applying the hazard analysis and critical control points to irradiated ready-to-eat meals

International Nuclear Information System (INIS)

Haruvy, Y.F.

2009-01-01

The classical methodology of hazard analysis and critical control points focuses on hazards and related implications. A new methodology is suggested here, one that attempts at a systematic simultaneous assessment of safety hazards, sensorial failures and economic risks, and the critical control points necessary for their early detection and/or prevention of their potential outcomes. The new methodology also attempts to combine the three parameters to form a qualitative prioritization of the numerous control points and to screen those that can be cost effective for implementation. This is demonstrated in this paper for a complex product, i.e. radiation sterilized ready-to-eat meals. Hence, a fourth parameter specific to this product - the radiation specific pitfall - is also assessed. The advantages and drawbacks of the combined assessment methodology are described and their overall possible impact is discussed. Finally, the suggested combined assessment and control system for ensuring the safety and quality of food can provide a more structured and critical approach to control identified hazards, compared with that achievable by traditional inspection and quality control procedures. It has the potential to identify areas of concern where failure has not yet been experienced, making it particularly useful for new operations and products thereafter. (author)

78 FR 24309 - Pipeline and Hazardous Materials Safety Administration

Science.gov (United States)

2013-04-24

... DEPARTMENT OF TRANSPORTATION Pipeline and Hazardous Materials Safety Administration List of Special Permit Applications Delayed AGENCY: Pipeline and Hazardous Materials Safety Administration (PHMSA..., Pipeline and Hazardous Materials Safety Administration, U.S. Department of Transportation, East Building...

Occurrence and determinants of increases in blood lead levels in children shortly after lead hazard control activities

International Nuclear Information System (INIS)

Clark, Scott; Grote, JoAnn; Wilson, Jonathan; Succop, Paul; Chen Mei; Galke, Warren; McLaine, Pat

2004-01-01

This study is an examination of the effect of lead hazard control strategies on children's blood lead levels immediately after an intervention was conducted as part of the US Department of Housing and Urban Development's Lead-Based Paint Hazard Control Grant Program. Fourteen state and local government grantees participated in the evaluation. The findings indicated an overall average reduction in the blood lead levels of 869 children soon after the implementation of lead hazard controls. However, 9.3% of these children (n=81) had blood lead increases of 5 μg/dL or more. Data routinely collected as part of the evaluation, as well as additional information supplied by the individual programs, were used to determine potential reasons for these observed increases in blood lead. A logistic regression analysis indicated that three principal factors were associated with the blood lead increases: the number of exterior deteriorations present in the child's home (prior to intervention), the educational level of the female parent or guardian of the child, and the child's age. The statistical analysis did not find evidence that children living in households that either did not relocate or relocated for less than the full work period were significantly more likely to have a blood lead increase equal to or greater than 5 μg/dL than children living in households that fully relocated. Statistical analyses also did not reveal any single interior strategy to be more or less likely than others to be associated with a blood lead increase of 5 μg/dL or more

Application of hazard analysis critical control points (HACCP) to organic chemical contaminants in food.

Science.gov (United States)

Ropkins, K; Beck, A J

2002-03-01

Hazard Analysis Critical Control Points (HACCP) is a systematic approach to the identification, assessment, and control of hazards that was developed as an effective alternative to conventional end-point analysis to control food safety. It has been described as the most effective means of controlling foodborne diseases, and its application to the control of microbiological hazards has been accepted internationally. By contrast, relatively little has been reported relating to the potential use of HACCP, or HACCP-like procedures, to control chemical contaminants of food. This article presents an overview of the implementation of HACCP and discusses its application to the control of organic chemical contaminants in the food chain. Although this is likely to result in many of the advantages previously identified for microbiological HACCP, that is, more effective, efficient, and economical hazard management, a number of areas are identified that require further research and development. These include: (1) a need to refine the methods of chemical contaminant identification and risk assessment employed, (2) develop more cost-effective monitoring and control methods for routine chemical contaminant surveillance of food, and (3) improve the effectiveness of process optimization for the control of chemical contaminants in food.

76 FR 45332 - Pipeline and Hazardous Materials Safety Administration

Science.gov (United States)

2011-07-28

... DEPARTMENT OF TRANSPORTATION Pipeline and Hazardous Materials Safety Administration Office of... Hazardous Materials Safety Administration (PHMSA), DOT. ACTION: List of Applications for Modification of..., 2011. ADDRESSES: Record Center, Pipeline and Hazardous Materials Safety Administration, U.S. Department...

Hazard Identification, Risk Assessment and Risk Control (HIRARC Accidents at Power Plant

Directory of Open Access Journals (Sweden)

Ahmad Asmalia Che

2016-01-01

Full Text Available Power plant had a reputation of being one of the most hazardous workplace environments. Workers in the power plant face many safety risks due to the nature of the job. Although power plants are safer nowadays since the industry has urged the employer to improve their employees’ safety, the employees still stumble upon many hazards thus accidents at workplace. The aim of the present study is to investigate work related accidents at power plants based on HIRARC (Hazard Identification, Risk Assessment and Risk Control process. The data were collected at two coal-fired power plant located in Malaysia. The finding of the study identified hazards and assess risk relate to accidents occurred at the power plants. The finding of the study suggested the possible control measures and corrective actions to reduce or eliminate the risk that can be used by power plant in preventing accidents from occurred

Physical hazards (noise, heat, vibration, illumination) - control at work place, methods and strategies

International Nuclear Information System (INIS)

Bose, M.; Srivastava, P.; Ganesh, G.

2016-01-01

The industrial work is getting modernized more day by day leading to more physical hazard. It is forcing the line management stressed upon in relation to the work place physical hazard. In order to keep the work place free from physical hazard it is required to use proper tool like work place assessment, measuring the parameters and analyze the end result which force us to take proper control measures to check and eliminate the physical hazard. (author)

EMERGENCY RESPONSE PROCEDURES FOR CONTROL OF HAZARDOUS SUBSTANCE RELEASES

Science.gov (United States)

Information is provided for selecting the best spill stabilization controls for hazardous substances regulated by the Comprehensive Enviromental Response, Compensation and Liability Act of 1980 (CERCLA). Information is also provided on the onsite assessment of spill severity, app...

Pasteurised milk and implementation of HACCP (Hazard Analysis Critical Control Point

Directory of Open Access Journals (Sweden)

T.B Murdiati

2004-10-01

Full Text Available The purpose of pasteurisation is to destroy pathogen bacteria without affecting the taste, flavor, and nutritional value. A study on the implementation of HACCP (Hazard Analysis Critical Control Point in producing pasteurized milk was carried out in four processing unit of pasteurised milk, one in Jakarta, two in Bandung and one in Bogor. The critical control points in the production line were identified. Milk samples were collected from the critical points and were analysed for the total number of microbes. Antibiotic residues were detected on raw milks. The study indicated that one unit in Bandung dan one unit in Jakarta produced pasteurized milk with lower number of microbes than the other units, due to better management and control applied along the chain of production. Penisilin residues was detected in raw milk used by unit in Bogor. Six critical points and the hazard might arise in those points were identified, as well as how to prevent the hazards. Quality assurance system such as HACCP would be able to produce high quality and safety of pasteurised milk, and should be implemented gradually.

FEMA DFIRM Flood Hazard Areas

Data.gov (United States)

Minnesota Department of Natural Resources — FEMA flood hazard delineations are used by the Federal Emergency Management Agency (FEMA) to designate the Special Flood Hazard Area (SFHA) and for insurance rating...

29 CFR 1917.25 - Fumigants, pesticides, insecticides and hazardous preservatives (see also § 1917.2 Hazardous...

Science.gov (United States)

2010-07-01

... 29 Labor 7 2010-07-01 2010-07-01 false Fumigants, pesticides, insecticides and hazardous..., DEPARTMENT OF LABOR (CONTINUED) MARINE TERMINALS Marine Terminal Operations § 1917.25 Fumigants, pesticides... fumigants, pesticides or hazardous preservatives have created a hazardous atmosphere. These signs shall note...

A risk perception gap? Comparing expert, producer and consumer prioritization of food hazard controls.

Science.gov (United States)

Hartmann, Christina; Hübner, Philipp; Siegrist, Michael

2018-06-01

Using a survey approach, the study examined how experts (i.e. food control representatives), producers (i.e. food industry representatives) and consumers prioritized control activities for 28 hazards related to food and other everyday items. The investigated hazards encompassed a wide range of safety issues, including health risks, consumer deception and poor food hygiene behaviour. The participants included 41 experts, 138 producers and 243 consumers from the German- and French-speaking parts of Switzerland. Based on detailed descriptions of the hazards, they were asked to rank these on a score sheet in terms of the perceived importance of monitoring by food control authorities. A between-group comparison of average rankings showed that consumers and experts differed significantly in relation to 17 of the 28 hazards. While the experts assigned higher priority to hazards related to everyday items such as nitrosamine in mascara and chromium VI in leather products, producers and consumers tended to prioritize products related to plant treatment and genetic modification of food and feeds. Producer and consumer rankings of the hazards were highly correlated (r = .96, p < .001). Rankings were also similar among participants from the two cultural regions (i.e. German and French-speaking parts of Switzerland). Copyright © 2018 Elsevier Ltd. All rights reserved.

Intelligent systems for remote decommissioning in hazardous environments

International Nuclear Information System (INIS)

Drotning, W.D.; Bennett, P.C.

1991-01-01

This paper reports on investigation of advanced handling technologies utilizing intelligent machines being supported jointly by the U.S. Department of Energy Offices of Civilian Radioactive Waste Management and Environmental Restoration and Waste Management for automation of transportation package handling operations at nuclear facilities and of nuclear waste site remediation efforts. Handling operation requirements include identification, location, and health physics operations, followed by bolting/unbolting operations and package disassembly. To accommodate these operations and the diversity of packages, fast model-based automated programming and force feedback control of a robotic control has been demonstrated for application to hazardous material cleanup. In this application, a graphical interface is used to simulate and evaluate operator-controlled motions and provide telerobotic control of the system. Remote automated handling technologies developed through these programs have the potential to decrease worker exposure and increase efficiency during decommissioning activities in hazardous environments

Hazard banding in compliance with the new Globally Harmonised System (GHS) for use in control banding tools.

Science.gov (United States)

Arnone, Mario; Koppisch, Dorothea; Smola, Thomas; Gabriel, Stefan; Verbist, Koen; Visser, Remco

2015-10-01

Many control banding tools use hazard banding in risk assessments for the occupational handling of hazardous substances. The outcome of these assessments can be combined with advice for the required risk management measures (RMMs). The Globally Harmonised System of Classification and Labelling of Chemicals (GHS) has resulted in a change in the hazard communication elements, i.e. Hazard (H) statements instead of Risk-phrases. Hazard banding schemes that depend on the old form of safety information have to be adapted to the new rules. The purpose of this publication is to outline the rationales for the assignment of hazard bands to H statements under the GHS. Based on this, this publication proposes a hazard banding scheme that uses the information from the safety data sheets as the basis for assignment. The assignment of hazard bands tiered according to the severity of the underlying hazards supports the important principle of substitution. Additionally, the set of assignment rules permits an exposure-route-specific assignment of hazard bands, which is necessary for the proposed route-specific RMMs. Ideally, all control banding tools should apply the same assignment rules. This GHS-compliant hazard banding scheme can hopefully help to establish a unified hazard banding strategy in the various control banding tools. Copyright © 2015 Elsevier Inc. All rights reserved.

Adaption of the Magnetometer Towed Array geophysical system to meet Department of Energy needs for hazardous waste site characterization

International Nuclear Information System (INIS)

Cochran, J.R.; McDonald, J.R.; Russell, R.J.; Robertson, R.; Hensel, E.

1995-10-01

This report documents US Department of Energy (DOE)-funded activities that have adapted the US Navy's Surface Towed Ordnance Locator System (STOLS) to meet DOE needs for a ''... better, faster, safer and cheaper ...'' system for characterizing inactive hazardous waste sites. These activities were undertaken by Sandia National Laboratories (Sandia), the Naval Research Laboratory, Geo-Centers Inc., New Mexico State University and others under the title of the Magnetometer Towed Array (MTA)

Effect of systematic ergonomic hazard identification and control implementation on musculoskeletal disorder and injury risk.

Science.gov (United States)

Cantley, Linda F; Taiwo, Oyebode A; Galusha, Deron; Barbour, Russell; Slade, Martin D; Tessier-Sherman, Baylah; Cullen, Mark R

2014-01-01

This study aimed to examine the effect of an ergonomic hazard control (HC) initiative, undertaken as part of a company ergonomics standard, on worker injury risk. Using the company's ergonomic hazards database to identify jobs with and without ergonomic HC implementation and linking to individual job and injury histories, injury risk among person-jobs with HC implementation (the HC group) was compared to those without HC (NoHC group) using random coefficient models. Further analysis of the HC group was conducted to determine the effect of additional ergonomic hazards controlled on injury risk. Among 123 jobs at 17 plant locations, 347 ergonomic hazards were quantitatively identified during the study period. HC were implemented for 204 quantified ergonomic hazards in 84 jobs, impacting 10 385 persons (12 967 person-jobs). No HC were implemented for quantified ergonomic hazards in the remaining 39 jobs affecting 4155 persons (5046 person-jobs). Adjusting for age, sex, plant origin, and year to control for any temporal trend in injury risk, the relative risk (RR) for musculoskeletal disorder (MSD) was 0.85 and the RR for any injury or MSD was 0.92 in the HC compared to NoHC group. Among the HC group, each ergonomic hazard controlled was associated with risk reduction for MSD and acute injury outcomes (RR 0.93). Systematic ergonomic HC through participatory ergonomics, as part of a mandatory company ergonomics standard, is associated with MSD and injury risk reduction among workers in jobs with HC implemented.

FEMA Hazard Mitigation Grants Program Summary

Data.gov (United States)

Department of Homeland Security — The Hazard Mitigation Grant Program (HMGP, CFDA Number: 97.039) provides grants to States and local governments to implement long-term hazard mitigation measures...

Intelligent systems for remote decommissioning in hazardous environments

International Nuclear Information System (INIS)

Drotning, W.D.; Bennett, P.C.

1991-01-01

Investigation of advanced technologies utilizing intelligent machines is being supported jointly by the US Department of Energy Offices of Civilian Radioactive Waste Management (DOE/RW) and Environmental Restoration and Waste Management (DOE/EM) for automation of transportation package handling operations at nuclear facilities and of nuclear waste site remediation efforts. Handling operation requirements include identification, location, and health physics operation, followed by bolting/unbolting operations and package disassembly. To accommodate these operations and the diversity of packages, fast model-based automated programming and force feedback control of a robotic cask handling system were developed. In addition, sensor-directed model-based robotic control has been demonstrated for application to hazardous material cleanup. In this application, a graphical interface is used to simulate and evaluate operator-controlled motions and provide telerobotic control of the system. Remote automated handling technologies developed through these programs have the potential to decrease worker exposure and increase efficiency during decommissioning activities in hazardous environments. 8 refs., 4 figs

Hazard classification of environmental restoration activities at the INEL

International Nuclear Information System (INIS)

Peatross, R.G.

1996-04-01

The following documents require that a hazard classification be prepared for all activities for which US Department of Energy (DOE) has assumed environmental, safety, and health responsibility: the DOE Order 5481.1B, Safety Analysis and Review System and DOE Order 5480.23, Nuclear Safety Analysis Reports. A hazard classification defines the level of hazard posed by an operation or activity, assuming an unmitigated release of radioactive and nonradioactive hazardous material. For environmental restoration activities, the release threshold criteria presented in Hazard Baseline Documentation (DOE-EM-STD-5502-94) are used to determine classifications, such as Radiological, Nonnuclear, and Other Industrial facilities. Based upon DOE-EM-STD-5502-94, environmental restoration activities in all but one of the sites addressed by the scope of this classification (see Section 2) can be classified as ''Other Industrial Facility''. DOE-EM-STD-5502-94 states that a Health and Safety Plan and compliance with the applicable Occupational Safety and Health Administration (OSHA) standards are sufficient safety controls for this classification

Innovative technologies for the treatment of hazardous and mixed wastes

International Nuclear Information System (INIS)

Eyman, L.D.; Anderson, T.D.

1988-01-01

The treatment, storage, and disposal of hazardous and mixed wastes incur significant costs for Department of Energy (DOE) installations. These wastes must be managed under strict environmental controls and regulations to prevent the possibility of migration of hazardous materials to the biosphere. Through the Hazardous Waste Remedial Actions Program, the DOE is seeking to develop innovative ways of improving current treatment technologies to eliminate the hazardous components of wastes, reduce waste management costs, and minimize the volume requiring disposal as hazardous or mixed waste. Sponsored projects progress from research and development to field demonstration. Among the innovative technologies under development are supercritical water oxidation of hazardous chemicals, microwave-assisted destruction of chlorinated hydrocarbons, paramagnetic separation of metals from waste, detoxification and reclamation of waste acid, nitrate destruction through calcination, treatment/disposal of reactive metals, and methodologies for encapsulation. Technologies at a demonstration phase include detoxification of mixed waste sludge, microbial degradation of polychlorinated biphenyls in soil, and the remediation process for a hydrocarbon spill. 14 refs

Administrative goals and safety standards for hazard control on forested recreation sites

Science.gov (United States)

Lee A. Paine

1973-01-01

For efficient control of tree hazard on recreation sites, a specific administrative goal must be selected. A safety standard designed to achieve the selected goal and a uniform hazard-rating procedure will then promote a consistent level of safety at an acceptable cost. Safety standards can be established with the aid of data for past years, and dollar evaluations are...

Hazardous materials management and control program at Oak Ridge National Laboratory - environmental protection

International Nuclear Information System (INIS)

Eisenhower, B.M.; Oakes, T.W.

1982-01-01

In the Federal Register of May 19, 1980, the US Environmental Protection Agency promulgated final hazardous waste regulations according to the Resource Conservation and Recovery Act (RCRA) of 1976. The major substantive portions of these regulations went into effect on November 19, 1980, and established a federal program to provide comprehensive regulation of hazardous waste from its generation to its disposal. In an effort to comply with these regulations, a Hazardous Materials Management and Control Program was established at Oak Ridge National Laboratory. The program is administered by two Hazardous Materials Coordinators, who together with various support groups, ensure that all hazardous materials and wastes are handled in such a manner that all personnel, the general public, and the environment are adequately protected

Evaluation of an active learning module to teach hazard and risk in Hazard Analysis and Critical Control Points (HACCP) classes.

Science.gov (United States)

Oyarzabal, Omar A; Rowe, Ellen

2017-04-01

The terms hazard and risk are significant building blocks for the organization of risk-based food safety plans. Unfortunately, these terms are not clear for some personnel working in food manufacturing facilities. In addition, there are few examples of active learning modules for teaching adult participants the principles of hazard analysis and critical control points (HACCP). In this study, we evaluated the effectiveness of an active learning module to teach hazard and risk to participants of HACCP classes provided by the University of Vermont Extension in 2015 and 2016. This interactive module is comprised of a questionnaire; group playing of a dice game that we have previously introduced in the teaching of HACCP; the discussion of the terms hazard and risk; and a self-assessment questionnaire to evaluate the teaching of hazard and risk. From 71 adult participants that completed this module, 40 participants (56%) provided the most appropriate definition of hazard, 19 participants (27%) provided the most appropriate definition of risk, 14 participants (20%) provided the most appropriate definitions of both hazard and risk, and 23 participants (32%) did not provide an appropriate definition for hazard or risk. Self-assessment data showed an improvement in the understanding of these terms (P active learning modules to teach food safety classes. This study suggests that active learning helps food personnel better understand important food safety terms that serve as building blocks for the understanding of more complex food safety topics.

21 CFR 120.7 - Hazard analysis.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Hazard analysis. 120.7 Section 120.7 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN... hazards. The written hazard analysis shall consist of at least the following: (1) Identification of food...

Surface Fire Hazards Analysis Technical Report-Constructor Facilities

International Nuclear Information System (INIS)

Flye, R.E.

2000-01-01

The purpose of this Fire Hazards Analysis Technical Report (hereinafter referred to as Technical Report) is to assess the risk from fire within individual fire areas to ascertain whether the U.S. Department of Energy (DOE) fire safety objectives are met. The objectives identified in DOE Order 420.1, Change 2, Facility Safety, Section 4.2, establish requirements for a comprehensive fire and related hazards protection program for facilities sufficient to minimize the potential for: The occurrence of a fire or related event; A fire that causes an unacceptable on-site or off-site release of hazardous or radiological material that will threaten the health and safety of employees, the public, or the environment; Vital DOE programs suffering unacceptable interruptions as a result of fire and related hazards; Property losses from a fire and related events exceeding defined limits established by DOE; and Critical process controls and safety class systems being damaged as a result of a fire and related events

Safety analysis and review system: a Department of Energy safety assurance tool

International Nuclear Information System (INIS)

Rosenthal, H.B.

1981-01-01

The concept of the Safety Analysis and Review System is not new. It has been used within the Department and its predecessor agencies, Atomic Energy Commission (AEC) and Energy Research and Development Administration (ERDA), for over 20 years. To minimize the risks from nuclear reactor and power plants, the AEC developed a process to support management authorization of each operation through identification and analysis of potential hazards and the measures taken to control them. As the agency evolved from AEC through ERDA to the Department of Energy, its responsibilities were broadened to cover a diversity of technologies, including those associated with the development of fossil, solar, and geothermal energy. Because the safety analysis process had proved effective in a technology of high potential hazard, the Department investigated the applicability of the process to the other technologies. This paper describes the system and discusses how it is implemented within the Department

Health and safety information program for hazardous materials

International Nuclear Information System (INIS)

O'Brien, M.P.; Fallon, N.J.; Kuehner, A.V.

1979-01-01

The system is used as a management tool in several safety and health programs. It is used to: trace the use of hazardous materials and to determine monitoring needs; inform the occupational physician of the potential health problems associated with materials ordered by a given individual; inform the fire and rescue group of hazardous materials in a given building; provide waste disposal recommendations to the hazardous waste management group; assist the hazardous materials shipping coordinator in identifying materials which are regulated by the Department of Transportation; and guide management decisions in the area of recognizing and rectifying unsafe conditions. The information system has been expanded from a manual effort to provide a brief description of health hazards of chemicals used at the lab to a computerized health and safety information system which serves the needs of all personnel who may encounter the material in the course of their work. The system has been designed to provide information needed to control the potential problems associated with a hazardous material up to the time that it is consumed in a given operation or is sent to the waste disposal facility

Department of Energy Natural Phenomena Hazards Mitigation program

International Nuclear Information System (INIS)

Murray, R.C.

1993-01-01

This paper presents a summary of past and present accomplishments of the Natural Phenomena Hazards Program that has been ongoing at Lawrence Livermore National Laboratory since 1975. The Natural Phenomena covered includes earthquake; winds, hurricanes, and tornadoes; flooding and precipitation; lightning; and volcanic events. The work is organized into four major areas (1) Policy, requirements, standards, and guidance, (2) Technical support, research and development, (3) Technology transfer, and (4) Oversight

The Main Biological Hazards in Animal Biosafety Level 2 Facilities and Strategies for Control.

Science.gov (United States)

Li, Xiao Yan; Xue, Kang Ning; Jiang, Jin Sheng; Lu, Xuan Cheng

2016-04-01

Concern about the biological hazards involved in microbiological research, especially research involving laboratory animals, has increased in recent years. Working in an animal biosafety level 2 facility (ABSL-2), commonly used for research on infectious diseases, poses various biological hazards. Here, the regulations and standards related to laboratory biosafety in China are introduced, the potential biological hazards present in ABSL-2 facilities are analyzed, and a series of strategies to control the hazards are presented. Copyright © 2016 The Editorial Board of Biomedical and Environmental Sciences. Published by China CDC. All rights reserved.

Rockfall Hazard Process Assessment : [Project Summary

Science.gov (United States)

2017-10-01

The Montana Department of Transportation (MDT) implemented its Rockfall Hazard Rating System (RHRS) between 2003 and 2005, obtaining information on the state's rock slopes and their associated hazards. The RHRS data facilitated decision-making in an ...

How to control chemical hazards

CERN Multimedia

2012-01-01

Improving protection against chemical hazards is one of the 2012 CERN safety objectives identified by the Director General. Identifying and drawing up a complete inventory of chemicals, and assessing the associated risks are important steps in this direction.   The HSE Unit has drawn up safety rules, guidelines and forms to help you to meet this objective. We would like to draw your attention to: • safety guidelines C-0-0-1 and C-1-0-2 (now also available in French), which deal with the identification of hazardous chemicals and the assessment of chemical risk; • safety guideline C-1-0-1, which deals with the storage of hazardous chemicals. All safety documents can be consulted at: cern.ch/regles-securite The HSE Unit will be happy to answer any questions you may have. Write to us at: safety-general@cern.ch The HSE Unit

Basel Convention on the Control of Transboundary Movements of Hazardous Wastes and their Disposal: Final Act

International Nuclear Information System (INIS)

1989-03-01

The Conference on Plenipotentiaries on the Global Convention on the Control of Transboundary Movements of Hazardous Wastes was convened by the Executive Director of the United Nations Environment Programme (UNEP) pursuant to decision 14/30, adopted by the Governing Council of UNEP on 17 June 1987. The Conference adopted the Global Convention on the Control of Transboundary Movements of Hazardous Wastes and their Disposal. In the 29 articles of this Convention the definitions of hazardous wastes, the scope of the Convention, general obligations of the signatory parties, transboundary waste movement between Parties as well as through states which are not parties, illegal traffic, international control, liabilities, financial aspects, verification, accession and withdrawal of the Parties are defined in detail. There are 6 Annexes, including specifications of hazardous wastes, information requirements, notification rules, etc

Onsite transportation hazards assessment

International Nuclear Information System (INIS)

Burnside, M.E.

1998-01-01

This report documents the emergency preparedness Hazards Assessment for the onsite transportation of hazardous material at the Hanford Site. The assessment is required by US Department of Energy (DOE) Order 5500.3A and provides the technical basis for the emergency classification and response procedures. A distinction is made between onsite for the purpose of emergency preparedness and onsite for the purpose of applying US Department of Transportation (DOT) regulations. Onsite for the purpose of emergency preparedness is considered to be within the physical boundary of the entire Hanford Site. Onsite for the purpose of applying DOT regulations is north of the Wye Barricade

FEMA Hazard Mitigation Grants Program Summary - API

Data.gov (United States)

Department of Homeland Security — The Hazard Mitigation Grant Program (HMGP, CFDA Number: 97.039) provides grants to States and local governments to implement long-term hazard mitigation measures...

Plutonium Finishing Plant (PFP) hazards assessment

International Nuclear Information System (INIS)

Campbell, L.R.

1998-01-01

This report documents the hazards assessment for the Plutonium Finishing Plant (PFP) located on the US Department of Energy (DOE) Hanford Site. This hazards assessment was conducted to provide the emergency planning technical basis for the PFP. DOE Orders require an emergency planning hazards assessment for each facility that has the potential to reach or exceed the lowest level emergency classification

Risk assessment for the transportation of hazardous waste and hazardous waste components of low-level mixed waste and transuranic waste for the US Department of Energy waste management programmatic environmental impact statement

International Nuclear Information System (INIS)

Lazaro, M.A.; Policastro, A.J.; Hartmann, H.M.; Chang, Y.S.

1996-12-01

This report, a supplement to Appendix E (Transportation Risk) of the U.S. Department of Energy Waste Management Programmatic Environmental Impact Statement (WM PEIS), provides additional information supporting the accident data for chemical risk assessment and health risk methodology described in that appendix (Part II) and presents the uncertainty analysis and on-site risk calculations. This report focuses on hazardous material truck accident rates, release probabilities, and release quantities; provides the toxicological values derived for each hazardous chemical assessed in the WM PEIS and further details on the derivation of health criteria; describes the method used in the transportation risk assessments to address potential additivity of health effects from simultaneous exposure to several chemicals and the method used to address transportation risks for maximally exposed individuals; presents an expanded discussion of the uncertainty associated with transportation risk calculations; and includes the results of the on-site transportation risk analysis. In addition, two addenda are provided to detail the risk assessments conducted for the hazardous components of low-level mixed waste (Addendum I) and transuranic waste (Addendum II)

Hazard management at the workplace

International Nuclear Information System (INIS)

Hasfazilah Hassan; Azimawati Ahmad; Syed Asraf Fahlawi Wafa S M Ghazi; Hairul Nizam Idris

2005-01-01

Failure to ensure health and safety environment at workplace will cause an accident involving loss to the time, human resource, finance and for the worse case effect the moral value of an organization. If we go through to the cause of the accident, it is impossible to have a totally safety workplace. It is because every process in work activities has it own hazard elements. The purpose of this paper is to discuss the best action to prevent from the hazard with a comprehensive and effectiveness hazard management. Hazard management is the one of the pro-active hazard control. With this we manage to identify and evaluate the hazard and control the hazard risk. Therefore, hazard management should be screened constantly and continuously to make sure work hazard always in control. (Author)

K Basin Hazard Analysis

Energy Technology Data Exchange (ETDEWEB)

PECH, S.H.

2000-08-23

This report describes the methodology used in conducting the K Basins Hazard Analysis, which provides the foundation for the K Basins Final Safety Analysis Report. This hazard analysis was performed in accordance with guidance provided by DOE-STD-3009-94, Preparation Guide for U. S. Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports and implements the requirements of DOE Order 5480.23, Nuclear Safety Analysis Report.

K Basin Hazard Analysis

International Nuclear Information System (INIS)

PECH, S.H.

2000-01-01

This report describes the methodology used in conducting the K Basins Hazard Analysis, which provides the foundation for the K Basins Final Safety Analysis Report. This hazard analysis was performed in accordance with guidance provided by DOE-STD-3009-94, Preparation Guide for U. S. Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports and implements the requirements of DOE Order 5480.23, Nuclear Safety Analysis Report

Evaluation of an active learning module to teach hazard and risk in Hazard Analysis and Critical Control Points (HACCP classes

Directory of Open Access Journals (Sweden)

Omar A. Oyarzabal

2017-04-01

Full Text Available The terms hazard and risk are significant building blocks for the organization of risk-based food safety plans. Unfortunately, these terms are not clear for some personnel working in food manufacturing facilities. In addition, there are few examples of active learning modules for teaching adult participants the principles of hazard analysis and critical control points (HACCP. In this study, we evaluated the effectiveness of an active learning module to teach hazard and risk to participants of HACCP classes provided by the University of Vermont Extension in 2015 and 2016. This interactive module is comprised of a questionnaire; group playing of a dice game that we have previously introduced in the teaching of HACCP; the discussion of the terms hazard and risk; and a self-assessment questionnaire to evaluate the teaching of hazard and risk. From 71 adult participants that completed this module, 40 participants (56% provided the most appropriate definition of hazard, 19 participants (27% provided the most appropriate definition of risk, 14 participants (20% provided the most appropriate definitions of both hazard and risk, and 23 participants (32% did not provide an appropriate definition for hazard or risk. Self-assessment data showed an improvement in the understanding of these terms (P < 0.05. Thirty participants (42% stated that the most valuable thing they learned with this interactive module was the difference between hazard and risk, and 40 participants (65% responded that they did not attend similar presentations in the past. The fact that less than one third of the participants answered properly to the definitions of hazard and risk at baseline is not surprising. However, these results highlight the need for the incorporation of modules to discuss these important food safety terms and include more active learning modules to teach food safety classes. This study suggests that active learning helps food personnel better understand important

The use of institutional controls at Department of Energy Oak Ridge Field Office environmental restoration sites

International Nuclear Information System (INIS)

White, R.K.; Swindle, D.W.; Redfearn, A.; King, A.D.

1992-01-01

This report summarizes some of the major issues related to the use of institutional controls at hazardous waste sites under the auspices of the Department of Energy Field Office, Oak Ridge/Environmental Restoration (DOE-OR/ER) Division. In particular, the report addresses the impacts that assumptions regarding institutional controls have on the results and interpretation of the risk assessment, both in the Remedial Investigation (RI) and the Feasibility Study (FS). Environmental restoration activities at DOE-OR/ER sites are primarily driven by CERCLA. Therefore, the report focuses on the approaches and assumptions relating to institutional controls under CERCLA. Also the report briefly outlines approaches adopted under other authorities such as RCRA and radiation regulatory authorities (such as NRC regulations/guidance, DOE orders, and EPA standards) in order to contrast these approaches to those adopted under CERCLA. In order to demonstrate the implications of the use of institutional controls at DOE facilities, this report summarizes the approaches and results of the recent baseline risk assessment for Solid Waste Storage Area 6 at Oak Ridge National Laboratory. The report concludes with possible options on the use of institutional controls at DOE-OR/ER sites

Impact of hazardous waste risks and liabilities on the contracting process

International Nuclear Information System (INIS)

Gleason, G.L.

1991-01-01

Hazardous waste risks include the following: (1) An emerging environmental cleanup industry that differs significantly from traditional engineering; (2) The inability to predict and control the subsurface environment; (3) The implementation of new and often untested technologies; (4) The statutory imposition of strict, joint and several, as well as retroactive, liability; (5) The lack of insurance and other risk-transfer mechanisms to protect against losses; (6) Costly and time consuming litigation to determine liability; and (7) Others. The liabilities associated with the risks inherent in hazardous waste cleanup directly impact hazardous waste contracting. Contract negotiations become onerous during discussions of liability, indemnification, and issues surrounding scope of work and other clauses. Other impacts include (1) Defensive engineering; (2) Lack of incentive to implement innovative technologies; (3) Increased costs to cover risks. Required client indemnification is a necessary and responsible risks management practice, regardless of whether the client is a federal or private client. Federal government indemnification authorities, as well as private contract indemnification mechanisms, will be explained and analyzed. Conflict of interest concerns are also of critical importance in the hazardous waste market, particularly due to concerns over the complexity of the litigation surrounding hazardous waste sites and the need to ensure unbiased results. Other examples of hazardous waste risk management impacts on contracting in the following market sectors will also be provided: (1) U.S. Environmental Protection Agency; (2) Department of Defense; (3) Department of Energy; and (4) Private sector contracts

Canister storage building hazard analysis report

International Nuclear Information System (INIS)

POWERS, T.B.

1999-01-01

This report describes the methodology used in conducting the Canister Storage Building (CSB) hazard analysis to support the CSB final safety analysis report (FSAR) and documents the results. The hazard analysis was performed in accordance with the DOE-STD-3009-94, ''Preparation Guide for US. Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports'', and meets the intent of HNF-PRO-704, ''Hazard and Accident Analysis Process''. This hazard analysis implements the requirements of DOE Order 5480.23, ''Nuclear Safety Analysis Reports''

New U.K. safety legislation and its effects on the control of radiological hazards

International Nuclear Information System (INIS)

Bell, B.H.J.; Luxon, S.G.

1977-01-01

This paper explains the objectives of the Health and Safety at Work etc Act 1974 and refers in particular to its effects on the control of hazards at nuclear installations and, more widely, on the control of radiological hazards generally. It deals also with the changes resulting from the setting up of the Health and Safety Commission and its Executive under the new Act, and the effects of these changes on the work of the Nuclear Installations Inspectorate. (auth.) [fr

Key parameters controlling radiology departments

International Nuclear Information System (INIS)

Busch, Hans-Peter

2011-01-01

For radiology departments and outstanding practises control and optimization of processes demand an efficient management based on key data. Systems of key data deliver indicators for control of medical quality, service quality and economics. For practices effectiveness (productivity), for hospitals effectiveness and efficiency are in the focus of economical optimization strategies. Task of daily key data is continuous monitoring of activities and workflow, task of weekly/monthly key data is control of data quality, process quality and achievement of objectives, task of yearly key data is determination of long term strategies (marketing) and comparison with competitors (benchmarking). Key parameters have to be defined clearly and have to be available directly. For generation, evaluation and control of key parameters suitable forms of organization and processes are necessary. Strategies for the future will be directed more to the total processes of treatment. To think in total processes and to steer and optimize with suitable parameters is the challenge for participants in the healthcare market of the future. (orig.)

Minutes from Department of Energy/Hazardous Waste Remedial Actions Program research and development technology needs assessment review meeting

International Nuclear Information System (INIS)

1989-01-01

On November 1--2, 1988, representatives of the Department of Energy (DOE) Headquarters, DOE Operations Offices, DOE contractors, and the Hazardous Waste Remedial Actions Program met in Salt Lake City, Utah, to select and prioritize candidate waste problems in need of research and development. The information gained will be used in planning for future research and development tasks and in restructuring current research activities to address the priority needs. All Operations Offices were represented by DOE staff and by contractor delegates from the area. This document summarizes the results of the meeting and lists the priority waste problems established

The effect of interior lead hazard controls on children's blood lead concentrations: a systematic evaluation.

Science.gov (United States)

Haynes, Erin; Lanphear, Bruce P; Tohn, Ellen; Farr, Nick; Rhoads, George G

2002-01-01

Dust control is often recommended to prevent children's exposure to residential lead hazards, but the effect of these controls on children's blood lead concentrations is uncertain. We conducted a systematic review of randomized, controlled trials of low-cost, lead hazard control interventions to determine the effect of lead hazard control on children's blood lead concentration. Four trials met the inclusion criteria. We examined mean blood lead concentration and elevated blood lead concentrations (> or = 10 microg/dL, > or = 15 microg/dL, and > or = 20 microg/dL) and found no significant differences in mean change in blood lead concentration for children by random group assignment (children assigned to the intervention group compared with those assigned to the control group). We found no significant difference between the intervention and control groups in the percentage of children with blood lead > or = 10 microg/dL, 29% versus 32% [odds ratio (OR), 0.85; 95% confidence interval (CI), 0.56-1.3], but there was a significant difference in the percentage of children with blood lead > or = 15 microg/dL between the intervention and control groups, 6% versus 14% (OR, 0.40; 95% CI, 0.21-0.80) and in the percentage of children with blood lead > or = 20 microg/dL between the intervention and control groups, 2% versus 6% (OR, 0.29; 95% CI, 0.10-0.85). We conclude that although low-cost, interior lead hazard control was associated with 50% or greater reduction in the proportion of children who had blood lead concentrations exceeding 15 microg/dL and > or = 20 microg/dL, there was no substantial effect on mean blood lead concentration.

Cold Vacuum Drying Facility hazard analysis report

Energy Technology Data Exchange (ETDEWEB)

Krahn, D.E.

1998-02-23

This report describes the methodology used in conducting the Cold Vacuum Drying Facility (CVDF) hazard analysis to support the CVDF phase 2 safety analysis report (SAR), and documents the results. The hazard analysis was performed in accordance with DOE-STD-3009-94, Preparation Guide for US Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports, and implements the requirements of US Department of Energy (DOE) Order 5480.23, Nuclear Safety Analysis Reports.

Cold Vacuum Drying Facility hazard analysis report

International Nuclear Information System (INIS)

Krahn, D.E.

1998-01-01

This report describes the methodology used in conducting the Cold Vacuum Drying Facility (CVDF) hazard analysis to support the CVDF phase 2 safety analysis report (SAR), and documents the results. The hazard analysis was performed in accordance with DOE-STD-3009-94, Preparation Guide for US Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports, and implements the requirements of US Department of Energy (DOE) Order 5480.23, Nuclear Safety Analysis Reports

Chemical inventory control program for mixed and hazardous waste facilities at SRS

International Nuclear Information System (INIS)

Ades, M.J.; Vincent, A.M. III.

1997-01-01

Mixed Waste (MW) and Hazardous Waste (HW) are being stored at the Savannah River Site (SRS) pending onsite and/or offsite treatment and disposal. The inventory control for these wastes has recently been brought under Technical Safety Requirements (TSR) in accordance with DOE Order 5480.22. With the TSRs was the question of the degree of rigor with which the inventory is to be tracked, considering that the variety of chemicals present, or that could be present, numbers in the hundreds. This paper describes the graded approach program to track Solid Waste (SW) inventories relative to TSRs. The approach uses a ratio of the maximum anticipated chemical inventory to the permissible inventory in accordance with Emergency Response Planning Guideline (ERPG) limits for on- and off-site receptors. A specific threshold ratio can then be determined. The chemicals above this threshold ratio are to be included in the chemical inventory control program. The chemicals that fall below the threshold ratio are managed in accordance with existing practice per State and RCRA hazardous materials requirements. Additionally, the facilities are managed in accordance with process safety management principles, specifically using process hazards analyses, which provides safety assurance for even the small quantities that may be excluded from the formal inventory control program. The method yields a practical approach to chemical inventory control, while maintaining appropriate chemical safety margins. The resulting number of specific chemicals that require inclusion in a rigorous inventory control program is greatly reduced by about 80%, thereby resulting in significant reduction in chemical data management while preserving appropriate safety margins

Risk assessment for the transportation of hazardous waste and hazardous waste components of low-level mixed waste and transuranic waste for the U.S. Department of Energy waste management programmatic environmental impact statement

International Nuclear Information System (INIS)

Lazaro, M.A.; Policastro, A.J.; Hartmann, H.M.

1995-04-01

This report, a supplement to Appendix E (Transportation Risk) of the U.S. Department of Energy Waste Management Programmatic Environmental Impact Statement (WM PEIS), provides additional information supporting the accident data for chemical risk assessment and health risk methodology described in that appendix (Part II), as well as providing the uncertainty analysis and on-site risk calculations. This report focuses on hazardous material truck accident rates, release probabilities, and release quantities; provides the toxicological values derived for each hazardous chemical assessed in the WM PEIS and further details on the derivation of health criteria; describes the method used in the transportation risk assessments to address potential additivity of health effects from simultaneous exposure to several chemicals and the method used to address transportation risks for maximally exposed individuals; presents an expanded discussion of the uncertainty associated with transportation risk calculations; and includes the results of the on-site transportation risk analysis. In addition, two addenda are provided to detail the risk assessments conducted for the hazardous components of low-level mixed waste (Addendum I) and transuranic waste (Addendum II)

Offsite transportation hazards assessment

International Nuclear Information System (INIS)

Burnside, M.E.

1997-01-01

This report documents the emergency preparedness Hazards Assessment for the offsite transportation of hazardous material from the Hanford Site. The assessment is required by the US Department of Energy (DOE) Order 151.1. Offsite transportation accidents are categorized using the DOE system to assist communication within the DOE and assure that appropriate assistance is provided to the people in charge at the scene. The assistance will initially include information about the load and the potential hazards. Local authorities will use the information to protect the public following a transportation accident. This Hazards Assessment will focus on the material being transported from the Hanford Site. Shipments coming to Hanford are the responsibility of the shipper and the carrier and, therefore, are not included in this Hazards Assessment, unless the DOE elects to be the shipper of record

The radon daughter radiation hazard in controlled recirculation systems

International Nuclear Information System (INIS)

Rolle, R.; Burton, R.C.

1987-01-01

In deep South African gold mines, controlled recirculation systems with air cooling are being used to an increasing extent to improve the thermal environment. Recirculation causes some air to reside in the working area for a longer time than would have occurred without recirculation. Since radon daughters grow spontaneously from radon there is some concern that, with the extended residence time, the potential radiation hazard could increase to an unacceptable level. This paper describes the results obtained from a theoretical model of a controlled recirculation system. Guidelines for the design of recirculation systems to control the radon daughter radiation, and to keep it within acceptable limits are provided. 3 refs., 5 figs

30 CFR 56.16004 - Containers for hazardous materials.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Containers for hazardous materials. 56.16004 Section 56.16004 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... Storage and Handling § 56.16004 Containers for hazardous materials. Containers holding hazardous materials...

30 CFR 57.16004 - Containers for hazardous materials.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Containers for hazardous materials. 57.16004 Section 57.16004 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... Storage and Handling § 57.16004 Containers for hazardous materials. Containers holding hazardous materials...

Public distrust and hazard management success at the Rocky Flats nuclear weapons plant

International Nuclear Information System (INIS)

Hohenemser, C.

1987-01-01

Based on experience gained while serving a public oversight commission appointed by the governor of Colorado, hazard management at the Department of Energy's Rocky Flats nuclear weapons plant is reviewed. Specific reference is made to the plant's history of controversy, its defense-in-depth strategy of hazard control, occupational health issues, public exposure to plutonium, and the assessment of low-probability, high-consequence risks. This leads to the conclusion that Rocky flats is, by any objective standard, a hazard management success. It follows that public distrust of Rocky Flats arises as much from fear and loathing of nuclear weapons themselves as from the manufacturing process by which they are made

78 FR 44625 - Proposed Information Collection (Open Burn Pit Registry Airborne Hazard Self-Assessment...

Science.gov (United States)

2013-07-24

... DEPARTMENT OF VETERANS AFFAIRS Proposed Information Collection (Open Burn Pit Registry Airborne... to ``OMB Control No. 2900--NEW, Open Burn Pit Registry Airborne Hazard Self-Assessment Questionnaire... health effects of service members' exposure to toxic airborne chemicals and fumes caused by open burn...

Seafood safety: economics of hazard analysis and Critical Control Point (HACCP) programmes

National Research Council Canada - National Science Library

Cato, James C

1998-01-01

.... This document on economic issues associated with seafood safety was prepared to complement the work of the Service in seafood technology, plant sanitation and Hazard Analysis Critical Control Point (HACCP) implementation...

Rockfall Hazard Process Assessment : Implementation Report

Science.gov (United States)

2017-10-01

The Montana Department of Transportation (MDT) commissioned a new research program to improve assessment and management of its rock slope assets. The Department implemented a Rockfall Hazard Rating System (RHRS) program in 2005 and wished to add valu...

Fire Department Emergency Response

International Nuclear Information System (INIS)

Blanchard, A.; Bell, K.; Kelly, J.; Hudson, J.

1997-09-01

In 1995 the SRS Fire Department published the initial Operations Basis Document (OBD). This document was one of the first of its kind in the DOE complex and was widely distributed and reviewed. This plan described a multi-mission Fire Department which provided fire, emergency medical, hazardous material spill, and technical rescue services

Rockfall Hazard Process Assessment : Final Project Report

Science.gov (United States)

2017-10-01

After a decade of using the Rockfall Hazard Rating System (RHRS), the Montana Department of Transportation (MDT) sought a reassessment of their rockfall hazard evaluation process. Their prior system was a slightly modified version of the RHRS and was...

K Basins Hazard Analysis

International Nuclear Information System (INIS)

WEBB, R.H.

1999-01-01

This report describes the methodology used in conducting the K Basins Hazard Analysis, which provides the foundation for the K Basins Safety Analysis Report (HNF-SD-WM-SAR-062/Rev.4). This hazard analysis was performed in accordance with guidance provided by DOE-STD-3009-94, Preparation Guide for U. S. Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports and implements the requirements of DOE Order 5480.23, Nuclear Safety Analysis Report

Electrical Switchgear Building No. 5010-ESF Fire Hazards Technical Report

International Nuclear Information System (INIS)

N.M. Ruonavaara

2001-01-01

The purpose of this Fire Hazards Analysis Technical Report (hereinafter referred to as Technical Report) is to assess the risk from fire within individual fire areas to ascertain whether the U.S. Department of Energy (DOE) fire safety objectives are met. The objectives, identified in DOE Order 420.1, Change 2, Fire Safety, Section 4.2, establish requirements for a comprehensive fire and related hazards protection program for facilities sufficient to minimize the potential for: (1) The occurrence of a fire or related event; (2) A fire that causes an unacceptable on-site or off-site release of hazardous or radiological material that will threaten the health and safety of the employees, the public, and the environment; (3) Vital DOE programs suffering unacceptable interruptions as a result of fire and related hazards; (4) Property losses from a fire and related events exceeding defined limits established by DOE; and (5) Critical process controls and safety class systems being damaged as a result of a fire and related event

Operation of controlled-air incinerators and design considerations for controlled-air incinerators treating hazardous and radioactive wastes

International Nuclear Information System (INIS)

McRee, R.E.

1986-01-01

This paper reviews the basic theory and design philosophies of the so-called controlled-air incinerator and examines the features of this equipment that make it ideally suited to the application of low-level radioactive waste disposal. Special equipment design considerations for controlled air incinerators treating hazardous and radioactive wastes are presented. 9 figures

Climate Prediction Center (CPC) U.S. Hazards Outlook

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Climate Prediction Center releases a US Hazards Outlook daily, Monday through Friday. The product highlights regions of anticipated hazardous weather during the...

Control Analysis of Hazards Potential in Crude Distiller Unit III PT. Pertamina (Persero) Refinery Unit III Plaju Tahun 2011

OpenAIRE

Matariani, Ade; Hasyim, Hamzah; Faisya, Achmad Fickry

2012-01-01

Background: Activities in CDU III are very risk to any hazards potential; because of that hazards potential is much needed in controlling the hazards potential to decrease the accidents and occupational diseases. The aim of this study was to analyze the controlling of hazards potential in CDU III PT. Pertamina (Persero) RU III Plaju in 2011. Method: This study was a qualitative study. The methods of data collection were using in-depth interview and observation. The total of informants in this...

77 FR 47779 - Arkansas: Final Authorization of State Hazardous Waste Management Program Revision

Science.gov (United States)

2012-08-10

... Protection Agency (EPA). ACTION: Direct final rule. SUMMARY: Arkansas has applied to the EPA for Final..., Arkansas Department of Pollution Control and Ecology (ADPC&E), revised its Regulation Number 23 from one of... Ecology Commission Regulation Number 23 (Hazardous Waste Management), adopted on April 25, 2008 and April...

Hazards Control Department. Annual technology review, 1981

International Nuclear Information System (INIS)

1982-01-01

This report is divided into three major sections. The first section covers the status of activities undertaken or continuing during the period; additional reports or separate publications will cover the final results of these activities. The second section contains reports on interesting activities of a more limited scope on which further reporting is not anticipated. The third section lists recent publications. Individual papers are included in the database

Hazards Control Department annual technology review, 1982

Energy Technology Data Exchange (ETDEWEB)

Griffith, R.V. (ed.)

1983-06-15

The report from Lawrence Livermore National Laboratory, which covers the period from October 1981 to September 1982, is divided into three major sections. The first section, progress reports, includes studies in areas of industrial hygiene, instrument development, environmental protection, radiation protection and fire safety. The second section, technical notes, contains reports on interesting activities of a more limited scope. The third section lists recent publications. (JMT)

Hazards Control Department annual technology review, 1984

International Nuclear Information System (INIS)

Griffith, R.V.; Anderson, K.J.

1985-01-01

The Annual Technology Review covers the period from October 1983 to September 1984. Topics reviewed include Nuclear Criticality Information System, nuclear dosimetry, personnel dosimetry, laser chemistry, electric filters and neutron spectrometry. Individual papers are indexed and abstracted for the data base. (DT)

Hazards Control Department annual technology review, 1985

International Nuclear Information System (INIS)

Griffith, R.V.; Anderson, K.J.

1986-01-01

The report highlights research performed from October 1984 to September 1985. The major sections cover the areas of industrial hygiene, aerosol physics, health physics, fire science, dosimetry, criticality safety, and safety analysis. Separate abstracts have been prepared for individual papers

Hazards Control Department annual technology review, 1982

International Nuclear Information System (INIS)

Griffith, R.V.

1983-01-01

The report from Lawrence Livermore National Laboratory, which covers the period from October 1981 to September 1982, is divided into three major sections. The first section, progress reports, includes studies in areas of industrial hygiene, instrument development, environmental protection, radiation protection and fire safety. The second section, technical notes, contains reports on interesting activities of a more limited scope. The third section lists recent publications

Hazards Control Department annual technology review, 1985

Energy Technology Data Exchange (ETDEWEB)

Griffith, R.V.; Anderson, K.J. (eds.)

1986-06-01

The report highlights research performed from October 1984 to September 1985. The major sections cover the areas of industrial hygiene, aerosol physics, health physics, fire science, dosimetry, criticality safety, and safety analysis. Separate abstracts have been prepared for individual papers. (ACR)

Natural Hazards Image Database

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Photographs and other visual media provide valuable pre- and post-event data for natural hazards. Research, mitigation, and forecasting rely on visual data for...

Selected problems of mine ventilation under conditions of gas and fire hazards. [Poland

Energy Technology Data Exchange (ETDEWEB)

Rosiek, F; Sikora, M; Urbanski, J

1984-01-01

Activities of the the Department for Ventilation, Fires and Occupational Safety in Wroclaw are evaluated. Until 1981 the Department concentrated its research programs on ventilation in copper mines; since 1982 its programs have also covered ventilation and hazards of endogenous fire in black coal mines. The Department investigated hazards of coal spontaneous combustion in Lower Silesian coal mines and proved that the hazards are associated with occurrence of specific layers in coal seams. When coal left in the goaf area came from a layer prone to spontaneous combustion hazards of endogenous fires were high. The Department developed a method for fire prevention using periodic reversal of goaf ventilation. Schemes for reverse ventilation are discussed.

222 S Laboratory complex hazards assessment

International Nuclear Information System (INIS)

Sutton, L.N.

1998-01-01

This report documents the hazards assessment for the 222-S Analytical Laboratory located on the US Department of Energy (DOE) Hanford Site. Operation of the laboratory is the responsibility of Waste Management Federal Services, Inc. (WMFS). This hazards assessment was conducted to provide the emergency planning technical basis for the 222-S Facility. DOE Orders require an emergency planning hazards assessment for each facility that has the potential to reach or exceed the lowest level emergency classification

Nontypical hazards associated with D ampersand D of power, weapons, and research and reactor plants

International Nuclear Information System (INIS)

Renk, F.A. Jr.

1995-01-01

Nontypical hazards such as asbestos and lead exist throughout the U.S. Department of Energy (DOE) weapons and research and reactor plants and commercial power plants. Most plants have encountered and identified these hazards during routine maintenance, modification, and repair activities. The decision to abate asbestos and lead is often cost-prohibitive and outweighed by the hazards created by the removal process; therefore, management-in-place concepts were and continue to be chosen as an alternative. This concept controls the hazard by using encapsulation, enclosure, and barrier installation techniques. Long-term operation and maintenance plans are then developed and implemented for periodic inspection, air monitoring, and repair. Although in-place-management plans tend to cover up the hazard, they provide an excellent source for the hazard recognition and identification phase by the paper trail the create

Implementation of hazard analysis and critical control point (HACCP) in dried anchovy production process

Science.gov (United States)

Citraresmi, A. D. P.; Wahyuni, E. E.

2018-03-01

The aim of this study was to inspect the implementation of Hazard Analysis and Critical Control Point (HACCP) for identification and prevention of potential hazards in the production process of dried anchovy at PT. Kelola Mina Laut (KML), Lobuk unit, Sumenep. Cold storage process is needed in each anchovy processing step in order to maintain its physical and chemical condition. In addition, the implementation of quality assurance system should be undertaken to maintain product quality. The research was conducted using a survey method, by following the whole process of making anchovy from the receiving raw materials to the packaging of final product. The method of data analysis used was descriptive analysis method. Implementation of HACCP at PT. KML, Lobuk unit, Sumenep was conducted by applying Pre Requisite Programs (PRP) and preparation stage consisting of 5 initial stages and 7 principles of HACCP. The results showed that CCP was found in boiling process flow with significant hazard of Listeria monocytogenesis bacteria and final sorting process with significant hazard of foreign material contamination in the product. Actions taken were controlling boiling temperature of 100 – 105°C for 3 - 5 minutes and training for sorting process employees.

78 FR 54956 - Agency Information Collection (Open Burn Pit Registry Airborne Hazard Self-Assessment...

Science.gov (United States)

2013-09-06

...: Open Burn Pit Registry Airborne Hazard Self-Assessment Questionnaire, VA Form 10-10066. Type of Review... services to Open Burn Pit Registry participants and improve VA's ability to understand the health effects... DEPARTMENT OF VETERANS AFFAIRS [OMB Control No. 2900-NEW] Agency Information Collection (Open Burn...

Occupational hazards among the abattoir workers associated with noncompliance to the meat processing and waste disposal laws in Malaysia

Directory of Open Access Journals (Sweden)

Abdullahi A

2016-07-01

Full Text Available Auwalu Abdullahi,1–3 Azmi Hassan,1 Norizhar Kadarman,2 Yakubu Muhammad Junaidu,3 Olanike Kudrat Adeyemo,4,5 Pei Lin Lua6 1Institute for Community Development and Quality of Life (i-CODE, Universiti Sultan Zainal Abidin (UniSZA, Kampus Gong Badak, 2Faculty of Medicine, Department of Community Medicine, Universiti Sultan Zainal Abidin (UniSZA, Kampus Kota, Kuala Terengganu, Terengganu, Malaysia; 3Department of Animal Health and Husbandry, Audu Bako College of Agriculture Dambatta, Kano, Nigeria; 4Center for Human and Environmental Toxicology, Department of Physiological Sciences, University of Florida, Gainesville, FL, USA; 5Department of Veterinary Public Health and Preventive Medicine, University of Ibadan, Ibadan, Nigeria; 6Community Health Research Cluster, Faculty of Health Sciences, Universiti Sultan Zainal Abidin (UniSZA, Kampus Gong Badak, Kuala Terengganu, Terengganu, Malaysia Purpose: This study aims to investigate the occupational hazards among the abattoir workers associated with noncompliance to the meat processing and waste disposal laws in Terengganu State, Malaysia. Occupational hazards are the major source of morbidity and mortality among the animal workers due to exposure to many hazardous situations in their daily practices. Occupational infections mostly contracted by abattoir workers could be caused by iatrogenic or transmissible agents, including viruses, bacteria, fungi, and parasites and the toxins produced by these organisms. Materials and methods: The methodology was based on a cross-sectional survey using cluster sampling technique in the four districts of Terengganu State, Malaysia. One hundred and twenty-one abattoir workers from five abattoirs were assessed using a validated structured questionnaire and an observation checklist. Results: The mean and standard deviation of occupational hazards scores of the workers were 2.32 (2.721. Physical, chemical, biological, psychosocial, musculoskeletal, and ergonomics hazards

The Hazard Analysis and Critical Control Points (HACCP) generic model for the production of Thai fermented pork sausage (Nham).

Science.gov (United States)

Paukatong, K V; Kunawasen, S

2001-01-01

Nham is a traditional Thai fermented pork sausage. The major ingredients of Nham are ground pork meat and shredded pork rind. Nham has been reported to be contaminated with Salmonella spp., Staphylococcus aureus, and Listeria monocytogenes. Therefore, it is a potential cause of foodborne diseases for consumers. A Hazard Analysis and Critical Control Points (HACCP) generic model has been developed for the Nham process. Nham processing plants were observed and a generic flow diagram of Nham processes was constructed. Hazard analysis was then conducted. Other than microbial hazards, the pathogens previously found in Nham, sodium nitrite and metal were identified as chemical and physical hazards in this product, respectively. Four steps in the Nham process have been identified as critical control points. These steps are the weighing of the nitrite compound, stuffing, fermentation, and labeling. The chemical hazard of nitrite must be controlled during the weighing step. The critical limit of nitrite levels in the Nham mixture has been set at 100-200 ppm. This level is high enough to control Clostridium botulinum but does not cause chemical hazards to the consumer. The physical hazard from metal clips could be prevented by visual inspection of every Nham product during stuffing. The microbiological hazard in Nham could be reduced in the fermentation process. The critical limit of the pH of Nham was set at lower than 4.6. Since this product is not cooked during processing, finally, educating the consumer, by providing information on the label such as "safe if cooked before consumption", could be an alternative way to prevent the microbiological hazards of this product.

HANDBOOK: QUALITY ASSURANCE/QUALITY CONTROL (QA/QC) PROCEDURES FOR HAZARDOUS WASTE INCINERATION

Science.gov (United States)

Resource Conservation and Recovery Act regulations for hazardous waste incineration require trial burns by permit applicants. uality Assurance Project Plan (QAPjP) must accompany a trial burn plan with appropriate quality assurance/quality control procedures. uidance on the prepa...

Hazard Communication Standard

International Nuclear Information System (INIS)

Sichak, S.

1991-01-01

The current rate of technological advances has brought with it an overwhelming increase in the usage of chemicals in the workplace and in the home. Coupled to this increase has been a heightened awareness in the potential for acute and chronic injuries attributable to chemical insults. The Hazard Communication Standard has been introduced with the desired goal of reducing workplace exposures to hazardous substances and thereby achieving a corresponding reduction in adverse health effects. It was created and proclaimed by the US Department of Labor and regulated by the Occupational Safety and Health Administration. 1 tab

SOLID-STATE CONTROLLED FIRE HAZARD DETECTION AND ...

African Journals Online (AJOL)

Microcontrol/er based fire hazard detection and quenching .system is developed, tested and found working satisfactory. Its response is very fast to quench thefire hazard before it spreads out. It is smart to ffiJoid any false alarming in case of momentary fire occurrence. ,Special emphasis has been laid down in choosing.

Software safety hazard analysis

International Nuclear Information System (INIS)

Lawrence, J.D.

1996-02-01

Techniques for analyzing the safety and reliability of analog-based electronic protection systems that serve to mitigate hazards in process control systems have been developed over many years, and are reasonably well understood. An example is the protection system in a nuclear power plant. The extension of these techniques to systems which include digital computers is not well developed, and there is little consensus among software engineering experts and safety experts on how to analyze such systems. One possible technique is to extend hazard analysis to include digital computer-based systems. Software is frequently overlooked during system hazard analyses, but this is unacceptable when the software is in control of a potentially hazardous operation. In such cases, hazard analysis should be extended to fully cover the software. A method for performing software hazard analysis is proposed in this paper

75 FR 63774 - Pipeline Safety: Safety of On-Shore Hazardous Liquid Pipelines

Science.gov (United States)

2010-10-18

... DEPARTMENT OF TRANSPORTATION Pipeline and Hazardous Materials Safety Administration 49 CFR Part... Pipelines AGENCY: Pipeline and Hazardous Materials Safety Administration (PHMSA), Department of... Gas Pipeline Safety Act of 1968, Public Law 90-481, delegated to DOT the authority to develop...

A comprehensive approach to managing hazardous materials

International Nuclear Information System (INIS)

Donovan, A.

1990-01-01

An increased emphasis on the need for environmental protection indicates that engineers must now consider the disposition of unused hazardous materials as waste. Before specifying and ordering materials, the engineer must consider the impact of the Resource Conservation and Recovery Act (RCRA) and the Occupational Safety and Health Administration's (OSHA's) Hazard Communication Standard. Many commonly used materials such as paint, solvents, glues, and sealants fall under the requirements of these regulations. This paper presents a plant to manage hazardous materials at the US Department of Energy's (DOE's) Waste Isolation Pilot Plant (WIPP), which is managed and operated by Westinghouse Electric Corporation. The basic elements of the plan are training, hazard communication, storage and handling, tracking, and disposal. Steps to be taken to develop the plan are outlined, problems and successes are addressed, and interactions among all affected departments are identified. The benefits of an organized and comprehensive approach to managing hazardous materials are decreased worker injuries, reduction of accidental releases, minimization of waste, and compliance with federal, state, and local safety and environmental laws. In summary, the benefits of an organized program for the management of hazardous materials include compliance with the Environmental Protection Agency's (EPA's) requirements, demonstration of Westinghouse's role as a responsible corporate entity, and reduction of waste management costs

Preventing tuberculosis in healthcare workers of the radiology department: a Malaysian perspective.

Science.gov (United States)

Tan, Lh; Kamarulzaman, A

2006-01-01

Tuberculosis (TB) is a well recognised occupational hazard for healthcare workers (HCWs). Concerns on the safety of healthcare settings in Malaysia was raised following a report of 25 HCWs working in 11 general hospitals in Malaysia who were infected with TB in 2004 being publicised in the media recently. As the disease burden in general is high in Malaysia, due attention should be given to this disease in our healthcare facilities including the radiology department, an often neglected area in TB infection control programmes. This article focuses on the key control measures that can be implemented in radiology departments in a developing country with limited resources.

Waste Encapsulation and Storage Facility (WESF) Hazards Assessment

International Nuclear Information System (INIS)

COVEY, L.I.

2000-01-01

This report documents the hazards assessment for the Waste Encapsulation and Storage Facility (WESF) located on the U.S. Department of Energy (DOE) Hanford Site. This hazards assessment was conducted to provide the emergency planning technical basis for WESF. DOE Orders require an emergency planning hazards assessment for each facility that has the potential to reach or exceed the lowest level emergency classification

U.S. Department of Energy Workers' mental models of radiation and chemical hazards in the workplace

International Nuclear Information System (INIS)

Quadrel, M.J.; Blanchard, K.A.; Lundgren, R.E.; McMakin, A.H.; Mosley, M.T.; Strom, D.J.

1994-05-01

A pilot study was performed to test the mental models methodology regarding knowledge and perceptions of U.S. Department of Energy contractor radiation workers about ionizing radiation and hazardous chemicals. The mental models methodology establishes a target population's beliefs about risks and compares them with current scientific knowledge. The ultimate intent is to develop risk communication guidelines that address information gaps or misperceptions that could affect decisions and behavior. In this study, 15 radiation workers from the Hanford Site in Washington State were interviewed about radiation exposure processes and effects. Their beliefs were mapped onto a science model of the same topics to see where differences occurred. In general, workers' mental models covered many of the high-level parts of the science model but did not have the same level of detail. The following concepts appeared to be well understood by most interviewees: types, form, and properties of workplace radiation; administrative and physical controls to reduce radiation exposure risk; and the relationship of dose and effects. However, several concepts were rarely mentioned by most interviewees, indicating potential gaps in worker understanding. Most workers did not discuss the wide range of measures for neutralizing or decontaminating individuals following internal contamination. Few noted specific ways of measuring dose or factors that affect dose. Few mentioned the range of possible effects, including genetic effects, birth defects, or high dose effects. Variables that influence potential effects were rarely discussed. Workers rarely mentioned how basic radiation principles influenced the source, type, or mitigation of radiation risk in the workplace

77 FR 41190 - Revised Document Posted: NIOSH List of Antineoplastic and Other Hazardous Drugs in Healthcare...

Science.gov (United States)

2012-07-12

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Centers for Disease Control and Prevention [Docket Number NIOSH-190] Revised Document Posted: NIOSH List of Antineoplastic and Other Hazardous Drugs in Healthcare Settings 2012, Correction AGENCY: National Institute for Occupational Safety and Health (NIOSH) of the...

Impacts of the use of institutional controls on risk assessments at Department of Energy facilities

International Nuclear Information System (INIS)

White, R.K.; Swindle, D.W. Jr.; Redfearn, A.; King, A.D.; Shaw, R.A.

1992-01-01

The United States Environmental Protection Agency (EPA), in the National Oil and Hazardous Waste Pollution Contingency Plan (NCP), has determined that institutional controls cannot be applied when determining baseline human health risks from exposure to contaminants present at a hazardous waste site. Environmental restoration activities at DOE-OR/ER sites are primarily driven by the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA). Therefore, the report focuses on the approaches and assumptions relating to institutional controls under CERCLA. In order to demonstrate the implications of the use of institutional controls at DOE facilities, this report summarizes the approaches and results of the recent baseline risk assessment for Solid Waste Storage Area 6 at Oak Ridge National Laboratory. The report concludes with possible options on the use of institutional controls at DOE-OR/ER sites. This report summarizes some of the major issues related to the use of institutional controls at hazardous waste sites under the auspices of DOE-OR/ER. In particular, the report addresses the impacts that assumptions regarding institutional controls have on the results and interpretation of the risk assessment, [in both the Remedial Investigation (RI) and the FS] and provides a case study from an actual DOE site

75 FR 12718 - Hazard Communication; Meetings Notice

Science.gov (United States)

2010-03-17

... 1926 [Docket No. OSHA-H022K-2006-0062, (formerly OSHA Docket No. H022K] RIN 1218-AC20 Hazard Communication; Meetings Notice AGENCY: Occupational Safety and Health Administration (OSHA), Department of Labor..., 2009, OSHA announced that it would hold informal public hearings on its proposal to revise the Hazard...

Hygienic-sanitary working practices and implementation of a Hazard Analysis and Critical Control Point (HACCP plan in lobster processing industries

Directory of Open Access Journals (Sweden)

Cristina Farias da Fonseca

2013-03-01

Full Text Available This study aimed to verify the hygienic-sanitary working practices and to create and implement a Hazard Analysis Critical Control Point (HACCP in two lobster processing industries in Pernambuco State, Brazil. The industries studied process frozen whole lobsters, frozen whole cooked lobsters, and frozen lobster tails for exportation. The application of the hygienic-sanitary checklist in the industries analyzed achieved conformity rates over 96% to the aspects evaluated. The use of the Hazard Analysis Critical Control Point (HACCP plan resulted in the detection of two critical control points (CCPs including the receiving and classification steps in the processing of frozen lobster and frozen lobster tails, and an additional critical control point (CCP was detected during the cooking step of processing of the whole frozen cooked lobster. The proper implementation of the Hazard Analysis Critical Control Point (HACCP plan in the lobster processing industries studied proved to be the safest and most cost-effective method to monitor each critical control point (CCP hazards.

78 FR 64425 - Current Good Manufacturing Practice and Hazard Analysis and Risk-Based Preventive Controls for...

Science.gov (United States)

2013-10-29

..., 507, and 579 [Docket No. FDA-2011-N-0922] Current Good Manufacturing Practice and Hazard Analysis and... requirements for current good manufacturing practice and hazard analysis and risk-based preventive controls for..., packing, or holding of animal food in two ways. First, it would create new current good manufacturing...

76 FR 23823 - Guidance for Industry on Fish and Fishery Products Hazards and Controls, Fourth Edition...

Science.gov (United States)

2011-04-28

... analysis and critical control point (HACCP) methods. DATES: Submit either electronic or written comments on... conducting a hazard analysis and implementing a HACCP plan. Although this guidance document is immediately in... appropriate HACCP plans for those hazards that are reasonably likely to occur. A summary of the changes from...

Semi-active control of monopile offshore wind turbines under multi-hazards

Science.gov (United States)

Sun, C.

2018-01-01

The present paper studies the control of monopile offshore wind turbines subjected to multi-hazards consisting of wind, wave and earthquake. A Semi-active tuned mass damper (STMD) with tunable natural frequency and damping ratio is introduced to control the dynamic response. A new fully coupled analytical model of the monopile offshore wind turbine with an STMD is established. The aerodynamic, hydrodynamic and seismic loading models are derived. Soil effects and damage are considered. The National Renewable Energy Lab monopile 5 MW baseline wind turbine model is employed to examine the performance of the STMD. A passive tuned mass damper (TMD) is utilized for comparison. Through numerical simulation, it is found that before damage occurs, the wind and wave induced response is more dominant than the earthquake induced response. With damage presence in the tower and the foundation, the nacelle and the tower response is increased dramatically and the natural frequency is decreased considerably. As a result, the passive TMD with fixed parameters becomes off-tuned and loses its effectiveness. In comparison, the STMD retuned in real-time demonstrates consistent effectiveness in controlling the dynamic response of the monopile offshore wind turbines under multi-hazards and damage with a smaller stroke.

Hazardous Substances Data Bank (HSDB)

Data.gov (United States)

U.S. Department of Health & Human Services — Comprehensive, peer-reviewed toxicology data for about 5,000 chemicals. The data bank focuses on the toxicology of potentially hazardous chemicals. It is enhanced...

Flood Hazard Areas - High Risk

Data.gov (United States)

Department of Homeland Security — The S_Fld_Haz_Ar table contains information about the flood hazards within the study area. A spatial file with locational information also corresponds with this data...

78 FR 24691 - Current Good Manufacturing Practice and Hazard Analysis and Risk-Based Preventive Controls for...

Science.gov (United States)

2013-04-26

... comments should be identified with the title ``Current Good Manufacturing Practice and Hazard Analysis and..., 114, 117, 120, 123, 129, 179, and 211 [Docket No. FDA-2011-N-0920] RIN 0910-AG36 Current Good Manufacturing Practice and Hazard Analysis and Risk- Based Preventive Controls for Human Food; Extension of...

Department of Energy Waste Information Network: Hazardous and mixed waste data management

International Nuclear Information System (INIS)

Fore, C.S.

1990-01-01

The Department of Energy (DOE) Waste Information Network (WIN) was developed through the efforts of the DOE Hazardous Waste Remedial Actions Program (HAZWRAP) Support Office (SO) to meet the programmatic information needs of the Director, Office of Environmental Restoration and Waste Management. WIN's key objective is to provide DOE Headquarters (HQ), DOE Operations Offices, and their contractors with an information management tool to support environmental restoration and waste management activities and to promote technology transfer across the DOE complex. WIN has evolved in various stages of growth driven by continued identification of user needs. The current system provides seven key features: technical information systems, bulletin boards, data file transfer, on-line conferencing, formal concurrence system, electronic messaging, and integrated spreadsheet/graphics. WIN is based on Digital Equipment Corporation;s (DEC) VAXcluster platform and is currently supporting nearly 1,000 users. An interactive menu system, DEC's ALL-IN-1 (1), provides easy access to all applications. WIN's many features are designed to provide the DOE waste management community with a repository of information management tools that are accessible, functional, and efficient. The type of tool required depends on the task to be performed, and WIN is equipped to serve many different needs. Each component of the system is evaluated for effectiveness for a particular purpose, ease of use, and quality of operation. The system is fully supported by project managers, systems analysts, and user assistance technicians to ensure subscribers of continued, uninterrupted service. 1 ref

Controlled air incineration of hazardous chemical and mixed waste at Los Alamos

International Nuclear Information System (INIS)

Borduin, L.C.; Hutchins, D.A.; Vavruska, J.J.; Warner, C.L.

1987-01-01

The Los Alamos National Laboratory (LANL) Controlled Air Incineration (CAI) system, originally developed for transuranic (TRU) waste volume reduction studies, is currently being qualified for hazardous chemical and mixed waste treatment under provisions of the Resource Conservation and Recovery Act (RCRA). The objective is to obtain a permanent RCRA Part B permit for thermal disposal of hazardous and mixed wastes generated by LANL. Constructed in the mid-1970s as a demonstration project for incineration of TRU solid wastes, the CAI process was substantially modified and tested in 1980-1983 for acceptance of both liquid and solid hazardous chemicals. Successful demonstration of TRU solid waste processing objectives in 1979 and later chemical waste incineration studies have been documented in several publications. In 1984, the LANL CAI became the first US Dept. of Energy (DOE) incinerator to be permitted for polychlorinated biphenyl disposal under the Toxic Substances Control Act. Following establishment of Environmental Protection Agency (EPA) jurisdiction over DOE chemical waste management in 1984, LANL sought and was granted interim status for the CAI and applied for a trial burn permit in the overall laboratory RCRA Part B application. A trial burn and final report have been completed; results have been submitted to EPA and the New Mexico Environmental Improvement Division. This paper provides an overview of trial burn planning and results together with the operational status of LANL's CAI

Delisting efforts for mixed radioactive and chemically hazardous waste at the Oak Ridge Gaseous Diffusion Plant

International Nuclear Information System (INIS)

Goodpasture, S.T.

1987-01-01

Presently, there are four hazardous wastes at the Oak Ridge Gaseous Diffusion Plant that are candidates for the delisting from the Resource Conservation and Recovery Act (RCRA) hazardous waste regulations. These candidates are the sludges from K-1407-B and C ponds, Central Neutralization Facility sludges, mixed sludges from Y-12 and the ash generated by the RCRA/Toxic Substances Control Act (TSCA) Incinerator. All of these hazardous wastes contain radioactive constituents as well as hazardous constituents. The delisting will be based upon the nonradioactive constituents. Whether the delisting petition is granted or not, the wastes will be handled according to the Department of Energy guidelines for radioactive wastes. The presentation discusses the methodologies for delisting these wastes and the rationale behind the processes

Mixed Integer PDE Constrained Optimization for the Control of a Wildfire Hazard

Science.gov (United States)

2017-01-01

Constrained Optimization for the Control of a Wildfire Hazard Herausgegeben von der Professor fur Angewandte Mathematik Professor Dr. rer. nat. Armin...and H.H. Tan . Finite difference methods for solving the two-dimensional advection-diffusion equation. Int. J. Numer. Meth. Fluids, 9:75-98, 1989. 6

Consistent natural phenomena design and evaluation guidelines for U.S. Department of Energy facilities

International Nuclear Information System (INIS)

Murray, R.C.; Short, S.A.

1989-01-01

Uniform design and evaluation guidelines for protection against natural phenomena hazards such as earthquakes, extreme winds, and flooding for facilities at Department of Energy (DOE) sites throughout the United States have been developed. The guidelines apply to design of new facilities and to evaluation or modification of existing facilities. These guidelines are an approach for design or evaluation for mitigating the effects of natural phenomena hazards. These guidelines are intended to control the level of conservatism introduced in the design/evaluation process such that all hazards are treated on a reasonably consistent and uniform basis and such that the level of conservatism is appropriate for facility characteristics such as importance, cost, and hazards to on-site personnel, the general public, and the environment. The philosophy and goals of these guidelines are covered by this paper

Canister storage building hazard analysis report

International Nuclear Information System (INIS)

Krahn, D.E.; Garvin, L.J.

1997-01-01

This report describes the methodology used in conducting the Canister Storage Building (CSB) hazard analysis to support the final CSB safety analysis report (SAR) and documents the results. The hazard analysis was performed in accordance with DOE-STD-3009-94, Preparation Guide for US Department of Energy Nonreactor Nuclear Facility Safety Analysis Report, and implements the requirements of DOE Order 5480.23, Nuclear Safety Analysis Report

DOE natural phenomenal hazards design and evaluation criteria

International Nuclear Information System (INIS)

Murray, R.C.; Nelson, T.A.; Short, S.A.; Kennedy, R.P.; Chander, H.; Hill, J.R.; Kimball, J.K.

1994-10-01

It is the policy of the Department of Energy (DOE) to design, construct, and operate DOE facilities so that workers, the general public, and the environment are protected from the impacts of natural phenomena hazards (NPH). Furthermore, DOE has established explicit goals of acceptable risk for NPH performance. As a result, natural phenomena hazard (earthquake, extreme wind, and flood) design and evaluation criteria for DOE facilities have been developed based on target probabilistic performance goals. These criteria include selection of design/evaluation NPH input from probabilistic hazard curves combined with commonly practiced deterministic response evaluation methods and acceptance criteria with controlled levels of conservatism. For earthquake considerations, conservatism is intentionally introduced in specification of material strengths and capacities, in the allowance of limited inelastic behavior, and by a seismic scale factor. Criteria have been developed following a graded approach for several performance goals ranging from that appropriate for normal-use facilities to that appropriate for facilities involving hazardous or critical operations. Performance goals are comprised of qualitative expressions of acceptable behavior and of target quantitative probabilities that acceptable limits of behavior are maintained. The criteria are simple procedures but have a rigorous basis. This paper addresses DOE seismic design and evaluation criteria

The practical implementation of integrated safety management for nuclear safety analysis and fire hazards analysis documentation

International Nuclear Information System (INIS)

COLLOPY, M.T.

1999-01-01

In 1995 Mr. Joseph DiNunno of the Defense Nuclear Facilities Safety Board issued an approach to describe the concept of an integrated safety management program which incorporates hazard and safety analysis to address a multitude of hazards affecting the public, worker, property, and the environment. Since then the U S . Department of Energy (DOE) has adopted a policy to systematically integrate safety into management and work practices at all levels so that missions can be completed while protecting the public, worker, and the environment. While the DOE and its contractors possessed a variety of processes for analyzing fire hazards at a facility, activity, and job; the outcome and assumptions of these processes have not always been consistent for similar types of hazards within the safety analysis and the fire hazard analysis. Although the safety analysis and the fire hazard analysis are driven by different DOE Orders and requirements, these analyses should not be entirely independent and their preparation should be integrated to ensure consistency of assumptions, consequences, design considerations, and other controls. Under the DOE policy to implement an integrated safety management system, identification of hazards must be evaluated and agreed upon to ensure that the public. the workers. and the environment are protected from adverse consequences. The DOE program and contractor management need a uniform, up-to-date reference with which to plan. budget, and manage nuclear programs. It is crucial that DOE understand the hazards and risks necessarily to authorize the work needed to be performed. If integrated safety management is not incorporated into the preparation of the safety analysis and the fire hazard analysis, inconsistencies between assumptions, consequences, design considerations, and controls may occur that affect safety. Furthermore, confusion created by inconsistencies may occur in the DOE process to grant authorization of the work. In accordance with

Staff technical position on investigations to identify fault displacement hazards and seismic hazards at a geologic repository

International Nuclear Information System (INIS)

McConnell, K.I.; Blackford, M.E.; Ibrahim, A.K.

1992-07-01

The purpose of this Staff Technical Position (STP) is to provide guidance to the US Department of Energy (DOE) on acceptable geologic repository investigations that can be used to identify fault displacement hazards and seismic hazards. ne staff considers that the approach this STP takes to investigations of fault displacement and seismic phenomena is appropriate for the collection of sufficient data for input to analyses of fault displacement hazards and seismic hazards, both for the preclosure and postclosure performance periods. However, detailed analyses of fault displacement and seismic data, such as those required for comprehensive assessments of repository performance, may identify the need for additional investigations. Section 2.0 of this STP describes the 10 CFR Part 60 requirements that form the basis for investigations to describe fault displacement hazards and seismic hazards at a geologic repository. Technical position statements and corresponding discussions are presented in Sections 3.0 and 4.0, respectively. Technical position topics in this STP are categorized thusly: (1) investigation considerations, (2) investigations for fault-displacement hazards, and (3) investigations for seismic hazards

Instrumentation and Controls Division, Technical Support Department Management Plan, FY 1993--FY 1996

Energy Technology Data Exchange (ETDEWEB)

Adkisson, B.P.; Kunselman, C.W.; Effler, R.P.; Miller, D.R.; Millet, A.J.; Stansberry, C.T.

1993-08-01

This report describes the organization, key functions, and major activities of the Technical Support Department The Department is the programmatic support element of the Instrumentation and Controls Division. The Department`s primary focus is the support of existing equipment and systems at Oak Ridge National Laboratory that are generally characterized as instrumentation and controls. The support takes the form of repair, calibration, fabrication, field engineering, preventive maintenance, software support, and record keeping.

National Flood Hazard Layer (NFHL)

Data.gov (United States)

Federal Emergency Management Agency, Department of Homeland Security — The National Flood Hazard Layer (NFHL) is a compilation of GIS data that comprises a nationwide digital Flood Insurance Rate Map. The GIS data and services are...

Sustainable System for Residual Hazards Management

International Nuclear Information System (INIS)

Kevin M. Kostelnik; James H. Clarke; Jerry L. Harbour

2004-01-01

Hazardous, radioactive and other toxic substances have routinely been generated and subsequently disposed of in the shallow subsurface throughout the world. Many of today's waste management techniques do not eliminate the problem, but rather only concentrate or contain the hazardous contaminants. Residual hazards result from the presence of hazardous and/or contaminated material that remains on-site following active operations or the completion of remedial actions. Residual hazards pose continued risk to humans and the environment and represent a significant and chronic problem that require continuous long-term management (i.e. >1000 years). To protect human health and safeguard the natural environment, a sustainable system is required for the proper management of residual hazards. A sustainable system for the management of residual hazards will require the integration of engineered, institutional and land-use controls to isolate residual contaminants and thus minimize the associated hazards. Engineered controls are physical modifications to the natural setting and ecosystem, including the site, facility, and/or the residual materials themselves, in order to reduce or eliminate the potential for exposure to contaminants of concern (COCs). Institutional controls are processes, instruments, and mechanisms designed to influence human behavior and activity. System failure can involve hazardous material escaping from the confinement because of system degradation (i.e., chronic or acute degradation) or by external intrusion of the biosphere into the contaminated material because of the loss of institutional control. An ongoing analysis of contemporary and historic sites suggests that the significance of the loss of institutional controls is a critical pathway because decisions made during the operations/remedial action phase, as well as decisions made throughout the residual hazards management period, are key to the long-term success of the prescribed system. In fact

Hazard Baseline Downgrade Effluent Treatment Facility

International Nuclear Information System (INIS)

Blanchard, A.

1998-01-01

This Hazard Baseline Downgrade reviews the Effluent Treatment Facility, in accordance with Department of Energy Order 5480.23, WSRC11Q Facility Safety Document Manual, DOE-STD-1027-92, and DOE-EM-STD-5502-94. It provides a baseline grouping based on the chemical and radiological hazards associated with the facility. The Determination of the baseline grouping for ETF will aid in establishing the appropriate set of standards for the facility

Handbook of hazardous waste management

International Nuclear Information System (INIS)

Metry, A.A.

1980-01-01

The contents of this work are arranged so as to give the reader a detailed understanding of the elements of hazardous waste management. Generalized management concepts are covered in Chapters 1 through 5 which are entitled: Introduction, Regulations Affecting Hazardous Waste Management, Comprehensive Hazardous Waste Management, Control of Hazardous Waste Transportation, and Emergency Hazardous Waste Management. Chapters 6 through 11 deal with treatment concepts and are entitled: General Considerations for Hazardous Waste Management Facilities, Physical Treatment of Hazardous Wastes, Chemical Treatment of Hazardous Wastes, Biological Treatment of Hazardous Wastes, Incineration of Hazardous Wastes, and Hazardous Waste Management of Selected Industries. Chapters 12 through 15 are devoted to ultimate disposal concepts and are entitled: Land Disposal Facilities, Ocean Dumping of Hazardous Wastes, Disposal of Extremely Hazardous Wastes, and Generalized Criteria for Hazardous Waste Management Facilities

75 FR 5536 - Pipeline Safety: Control Room Management/Human Factors, Correction

Science.gov (United States)

2010-02-03

... DEPARTMENT OF TRANSPORTATION Pipeline and Hazardous Materials Safety Administration 49 CFR Parts...: Control Room Management/Human Factors, Correction AGENCY: Pipeline and Hazardous Materials Safety... following correcting amendments: PART 192--TRANSPORTATION OF NATURAL AND OTHER GAS BY PIPELINE: MINIMUM...

Study on integrated approach of Nuclear Accident Hazard Predicting, Warning, and Optimized Controlling System based on GIS

International Nuclear Information System (INIS)

Tang Lijuan; Huang Shunxiang; Wang Xinming

2012-01-01

The issue of nuclear safety becomes the attention focus of international society after the nuclear accident happened in Fukushima. Aiming at the requirements of the prevention and controlling of Nuclear Accident establishment of Nuclear Accident Hazard Predicting, Warning and optimized Controlling System (NAPWS) is a imperative project that our country and army are desiderating, which includes multiple fields of subject as nuclear physics, atmospheric science, security science, computer science and geographical information technology, etc. Multiplatform, multi-system and multi-mode are integrated effectively based on GIS, accordingly the Predicting, Warning, and Optimized Controlling technology System of Nuclear Accident Hazard is established. (authors)

French people addressing environmental hazards (Eser 2013)

International Nuclear Information System (INIS)

Pautard, Eric; Moreau, Sylvain; Bottin, Anne; Kraszewski, Marlene; Fretin, David; Carriere, Celine; Bird, Geoffrey

2015-07-01

This publication presents the results of a survey, conducted towards the end of 2013, of 4,700 people resident in metropolitan France and its 'departements d'outre-mer' (DOM - overseas departments). The aim of the survey was to ascertain how French people perceive natural hazards (flooding, earthquakes, climate events, cyclones, etc.) and technological hazards (industrial and nuclear) to which they may be exposed. Questioned as to whether or not they felt exposed to one or several environmental hazards in their place of residence, French people's answers varied somewhat depending on the hazard invoked and place of residence. A strong feeling of exposure was expressed most frequently in the DOM. Respondents in both metropolitan France and DOM think that atmospheric pollution is a significant hazard (56%) but their opinions diverge partially where other hazards are concerned. Natural hazards (earthquakes and flooding) are cited most frequently overseas, whereas technological hazards (industrial and nuclear) are primarily metropolitan concerns. Climate change related hazards are seen as a threat by 56% of overseas respondents and by 42% in the mother country. In general, one-third of French people think that they are exposed to more than two environmental hazards. Unlike the younger members of the population, only one-quarter of respondents of 65 years of age or over felt exposed to three or more hazards. From municipal level databases providing information on exposure to flooding and technological and climate-related hazards, the survey indicates that a large majority of respondents living in these municipalities either do not feel at risk from existing hazards or feel that the risk is low (see figure below). It is in the area of climate-related hazards that awareness of threat seems to be highest in France, and more particularly in the DOM. In the face of the flooding that could affect them, overseas populations are more aware of this natural

Overview of Department of Energy programs

International Nuclear Information System (INIS)

Hill, J.R.

1985-01-01

An overview is presented of policies and standards of the US DOE in the protection of the public, government employees, and government property from damage caused by natural phenomena. Included are Department of Energy orders covering policy and standards for natural phenomena hazards mitigation and Office of Nuclear Safety projects related to natural phenomena hazards mitigation. National Federal programs, committees, and reports are listed. 18 references

Egyptian Environmental Activities and Regulations for Management of Hazardous Substances and Hazardous Wastes

International Nuclear Information System (INIS)

El Zarka, M.

1999-01-01

A substantial use of hazardous substances is essential to meet the social and economic goals of the community in Egypt. Agrochemicals are being used extensively to increase crop yield. The outdated agrochemicals and their empty containers represent a serious environmental problem. Industrial development in different sectors in Egypt obligates handling of huge amounts of hazardous substances and hazardous wastes. The inappropriate handling of such hazardous substances creates several health and environmental problems. Egypt faces many challenges to control safe handling of such substances and wastes. Several regulations are governing handling of hazardous substances in Egypt. The unified Environmental Law 4 for the year 1994 includes a full chapter on the Management of Hazardous Substances and Hazardous Wastes. National and international activities have been taken to manage hazardous substances and hazardous wastes in an environmental sound manner

HMPT: Hazardous Waste Transportation Live 27928, Test 27929

Energy Technology Data Exchange (ETDEWEB)

Simpson, Lewis Edward [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-03-17

HMPT: Hazardous Waste Transportation (Live 27928, suggested one time and associated Test 27929, required initially and every 36 months) addresses the Department of Transportation (DOT) function-specific training requirements of the hazardous materials packagings and transportation (HMPT) Los Alamos National Laboratory (LANL) lab-wide training. This course addresses the requirements of the DOT that are unique to hazardous waste shipments. Appendix B provides the Title 40 Code of Federal Regulations (CFR) reference material needed for this course.

Mixed waste removal from a hazardous waste storage tank

International Nuclear Information System (INIS)

Geber, K.R.

1993-01-01

The spent fuel transfer canal at the Oak Ridge Graphite Reactor was found to be leaking 400 gallons of water per day into the surrounding soil. Sampling of the sediment layer on the floor of the canal to determine the environmental impact of the leak identified significant radiological contamination and elevated levels of cadmium and lead which are hazardous under the Resource Conservation and Recovery Act (RCRA). Under RCRA regulations and Rules of Tennessee Department of Environment and Conservation, the canal was considered a hazardous waste storage tank. This paper describes elements of the radiological control program established in support of a fast-track RCRA closure plan that involved underwater mapping of the radiation fields, vacuuming, and ultra-filtration techniques that were successfully used to remove the mixed waste sediments and close the canal in a method compliant with state and federal regulations

Emergency Preparedness Hazards Assessment for solid waste management facilities in E-area not previously evaluated

International Nuclear Information System (INIS)

Hadlock, D.J.

1999-01-01

This report documents the facility Emergency Preparedness Hazards Assessment (EPHA) for the Solid Waste Management Department (SWMD) activities located on the Department of Energy (DOE) Savannah River Site (SRS) within E Area that are not described in the EPHAs for Mixed Hazardous Waste storage, the TRU Waste Storage Pads or the E-Area Vaults. The hazards assessment is intended to identify and analyze those hazards that are significant enough to warrant consideration in the SWMD operational emergency management program

Controlled air incineration of hazardous chemical waste at the Los Alamos National Laboratory

International Nuclear Information System (INIS)

Stretz, L.A.; Borduin, L.C.; Draper, W.E.; Koenig, R.A.; Vavruska, J.S.

1982-01-01

An incineration system, originally demonstrated as a transuranic (TRU) waste volume-reduction process, is described. The production-scale controlled air incinerator using commercially available equipment and technology was modified for solid radioactive waste service. The same incinerator and offgas treatment system has been modified further for use in evaluating the destruction of hazardous liquid wastes such as polychlorinated biphenyls (PCBs) and hazardous solid wastes such as pentachlorophenol (PCP)-treated wood. Results of a PCP-treated wood incineration test show a PCP destruction efficiency of greater than 99.99% in the primary chamber for the operating conditions investigated. Conditions and results for this test are described

PENERAPAN SISTEM HAZARD ANALYSIS CRITICAL CONTROL POINT (HACCP PADA PROSES PEMBUATAN KERIPIK TEMPE

Directory of Open Access Journals (Sweden)

Rahmi Yuniarti

2015-06-01

Full Text Available Malang is one of the industrial centers of tempe chips. To maintain the quality and food safety, analysis is required to identify the hazards during the production process. This study was conducted to identify the hazards during the production process of tempe chips and provide recommendations for developing a HACCP system. The phases of production process of tempe chips are started from slice the tempe, move it to the kitchen, coat it with flour dough, fry it in the pan, drain it, package it, and then storage it. There are 3 types of potential hazards in terms of biological, physical, and chemical during the production process. With the CCP identification, there are three processes that have Critical Control Point. There are the process of slicing tempe, immersion of tempe into the flour mixture and draining. Recommendations for the development of HACCP systems include recommendations related to employee hygiene, supporting equipment, 5-S analysis, and the production layout.

Methods for developing seismic and extreme wind-hazard models for evaluating critical structures and equipment at US Department of Energy facilities and commercial plutonium facilities in the United States

International Nuclear Information System (INIS)

Coats, D.W.; Murray, R.C.; Bernreuter, D.L.

1981-01-01

Lawrence Livermore National Laboratory (LLNL) is developing seismic and wind hazard models for the US Department of Energy (DOE). The work is part of a three-phase effort to establish building design criteria developed with a uniform methodology for seismic and wind hazards at the various DOE sites throughout the United States. In Phase 1, LLNL gathered information on the sites and their critical facilities, including nuclear reactors, fuel-reprocessing plants, high-level waste storage and treatment facilities, and special nuclear material facilities. Phase 2 - development of seismic and wind hazard models - is discussed in this paper, which summarizes the methodologies used by seismic and extreme-wind experts and gives sample hazard curves for the first sites to be modeled. These hazard models express the annual probability that the site will experience an earthquake (or windspeed) greater than some specified magnitude. In the final phase, the DOE will use the hazards models and LLNL-recommended uniform design criteria to evaluate critical facilities. The methodology presented in this paper also was used for a related LLNL study - involving the seismic assessment of six commercial plutonium fabrication plants licensed by the US Nuclear Regulatory Commission (NRC). Details and results of this reassessment are documented in reference

Hazardous Chemicals

Centers for Disease Control (CDC) Podcasts

Chemicals are a part of our daily lives, providing many products and modern conveniences. With more than three decades of experience, The Centers for Disease Control and Prevention (CDC) has been in the forefront of efforts to protect and assess people's exposure to environmental and hazardous chemicals. This report provides information about hazardous chemicals and useful tips on how to protect you and your family from harmful exposure.

[Introduction of hazard analysis and critical control points (HACCP) principles at the flight catering food production plant].

Science.gov (United States)

Popova, A Yu; Trukhina, G M; Mikailova, O M

In the article there is considered the quality control and safety system implemented in the one of the largest flight catering food production plant for airline passengers and flying squad. The system for the control was based on the Hazard Analysis And Critical Control Points (HACCP) principles and developed hygienic and antiepidemic measures. There is considered the identification of hazard factors at stages of the technical process. There are presented results of the analysis data of monitoring for 6 critical control points over the five-year period. The quality control and safety system permit to decline food contamination risk during acceptance, preparation and supplying of in-flight meal. There was proved the efficiency of the implemented system. There are determined further ways of harmonization and implementation for HACCP principles in the plant.

Recommendations for dealing with waste contaminated with Ebola virus: a Hazard Analysis of Critical Control Points approach.

Science.gov (United States)

Edmunds, Kelly L; Elrahman, Samira Abd; Bell, Diana J; Brainard, Julii; Dervisevic, Samir; Fedha, Tsimbiri P; Few, Roger; Howard, Guy; Lake, Iain; Maes, Peter; Matofari, Joseph; Minnigh, Harvey; Mohamedani, Ahmed A; Montgomery, Maggie; Morter, Sarah; Muchiri, Edward; Mudau, Lutendo S; Mutua, Benedict M; Ndambuki, Julius M; Pond, Katherine; Sobsey, Mark D; van der Es, Mike; Zeitoun, Mark; Hunter, Paul R

2016-06-01

To assess, within communities experiencing Ebola virus outbreaks, the risks associated with the disposal of human waste and to generate recommendations for mitigating such risks. A team with expertise in the Hazard Analysis of Critical Control Points framework identified waste products from the care of individuals with Ebola virus disease and constructed, tested and confirmed flow diagrams showing the creation of such products. After listing potential hazards associated with each step in each flow diagram, the team conducted a hazard analysis, determined critical control points and made recommendations to mitigate the transmission risks at each control point. The collection, transportation, cleaning and shared use of blood-soiled fomites and the shared use of latrines contaminated with blood or bloodied faeces appeared to be associated with particularly high levels of risk of Ebola virus transmission. More moderate levels of risk were associated with the collection and transportation of material contaminated with bodily fluids other than blood, shared use of latrines soiled with such fluids, the cleaning and shared use of fomites soiled with such fluids, and the contamination of the environment during the collection and transportation of blood-contaminated waste. The risk of the waste-related transmission of Ebola virus could be reduced by the use of full personal protective equipment, appropriate hand hygiene and an appropriate disinfectant after careful cleaning. Use of the Hazard Analysis of Critical Control Points framework could facilitate rapid responses to outbreaks of emerging infectious disease.

Microneedle Manufacture: Assessing Hazards and Control Measures

Directory of Open Access Journals (Sweden)

Alexander Martin

2017-10-01

Full Text Available Transdermal microneedles have captured the attention of researchers in relation to a variety of applications, and silicone-based moulds required to produce these systems are now widely available and can be readily manufactured on the lab bench. There is however some concern over the potential for accidental needlestick injuries and, as with any sharp hazard, the potential for blood-borne pathogen transmission must be considered. This follows from recent governmental concerns over the use of microneedle systems in dermabrasion. Despite the piercing nature of the microneedle patch sharing many similarities with conventional hypodermic needles, there are notable factors that mitigate the risk of contamination. A range of microneedle systems has been prepared using micromoulding techniques, and their puncture capability assessed. A critical assessment of the potential for accidental puncture and the control measures needed to ensure safe utilisation of the patch systems is presented.

Effectiveness of a Web-Based Intervention to Reduce Alcohol Consumption among French Hazardous Drinkers: A Randomized Controlled Trial

Science.gov (United States)

Guillemont, Juliette; Cogordan, Chloé; Nalpas, Bertrand; Nguyen-Thanh, Vi?t; Richard, Jean-Baptiste; Arwidson, Pierre

2017-01-01

This study aims to evaluate the effectiveness of a web-based intervention to reduce alcohol consumption among hazardous drinkers. A two-group parallel randomized controlled trial was conducted among adults identified as hazardous drinkers according to the Alcohol Use Disorders Identification Test. The intervention delivers personalized normative…

Compliance of SLAC's Laser Safety Program with OSHA Requirements for the Control of Hazardous Energy

International Nuclear Information System (INIS)

Woods, M.

2009-01-01

SLAC's COHE program requires compliance with OSHA Regulation 29CFR1910.147, 'The control of hazardous energy (lockout/tagout)'. This regulation specifies lockout/tagout requirements during service and maintenance of equipment in which the unexpected energization or start up of the equipment, or release of stored energy, could cause injury to workers. Class 3B and Class 4 laser radiation must be considered as hazardous energy (as well as electrical energy in associated equipment, and other non-beam energy hazards) in laser facilities, and therefore requires careful COHE consideration. This paper describes how COHE is achieved at SLAC to protect workers against unexpected Class 3B or Class 4 laser radiation, independent of whether the mode of operation is normal, service, or maintenance

Relative Hazard and Risk Measure Calculation Methodology

International Nuclear Information System (INIS)

Stenner, Robert D.; Strenge, Dennis L.; Elder, Matthew S.; Andrews, William B.; Walton, Terry L.

2003-01-01

The RHRM equations, as represented in methodology and code presented in this report, are primarily a collection of key factors normally used in risk assessment that are relevant to understanding the hazards and risks associated with projected mitigation, cleanup, and risk management activities. The RHRM code has broad application potential. For example, it can be used to compare one mitigation, cleanup, or risk management activity with another, instead of just comparing it to just the fixed baseline. If the appropriate source term data are available, it can be used in its non-ratio form to estimate absolute values of the associated controlling hazards and risks. These estimated values of controlling hazards and risks can then be examined to help understand which mitigation, cleanup, or risk management activities are addressing the higher hazard conditions and risk reduction potential at a site. Graphics can be generated from these absolute controlling hazard and risk values to graphically compare these high hazard and risk reduction potential conditions. If the RHRM code is used in this manner, care must be taken to specifically define and qualify (e.g., identify which factors were considered and which ones tended to drive the hazard and risk estimates) the resultant absolute controlling hazard and risk values

The application of hazard analysis and critical control points and risk management in the preparation of anti-cancer drugs.

Science.gov (United States)

Bonan, Brigitte; Martelli, Nicolas; Berhoune, Malik; Maestroni, Marie-Laure; Havard, Laurent; Prognon, Patrice

2009-02-01

To apply the Hazard analysis and Critical Control Points method to the preparation of anti-cancer drugs. To identify critical control points in our cancer chemotherapy process and to propose control measures and corrective actions to manage these processes. The Hazard Analysis and Critical Control Points application began in January 2004 in our centralized chemotherapy compounding unit. From October 2004 to August 2005, monitoring of the process nonconformities was performed to assess the method. According to the Hazard Analysis and Critical Control Points method, a multidisciplinary team was formed to describe and assess the cancer chemotherapy process. This team listed all of the critical points and calculated their risk indexes according to their frequency of occurrence, their severity and their detectability. The team defined monitoring, control measures and corrective actions for each identified risk. Finally, over a 10-month period, pharmacists reported each non-conformity of the process in a follow-up document. Our team described 11 steps in the cancer chemotherapy process. The team identified 39 critical control points, including 11 of higher importance with a high-risk index. Over 10 months, 16,647 preparations were performed; 1225 nonconformities were reported during this same period. The Hazard Analysis and Critical Control Points method is relevant when it is used to target a specific process such as the preparation of anti-cancer drugs. This method helped us to focus on the production steps, which can have a critical influence on product quality, and led us to improve our process.

Issues related to uncertainty in projections of hazardous and mixed waste volumes in the U.S. Department of Energy's environmental restoration program

International Nuclear Information System (INIS)

Picel, K.C.

1995-01-01

Projected volumes of contaminated media and debris at US Department of Energy (DOE) environmental restoration sites that are potentially subject to the hazardous waste provisions of the Resource Conservation and Recovery Act are needed to support programmatic planning. Such projections have been gathered in various surveys conducted under DOE's environmental restoration and waste management programs. It is expected that reducing uncertainty in the projections through review of existing site data and process knowledge and through further site characterization will result in substantially lowered projections. If promulgated, the US Environmental Protection Agency's Hazardous Waste Identification Rule would result in potentially even greater reductions in the projections when site conditions are reviewed under the provisions of the new rule. Reducing uncertainty in projections under current and future waste identification rules may be necessary to support effective remediation planning. Further characterization efforts that may be conducted should be designed to limit uncertainty in identifying volumes of wastes to the extent needed to support alternative selection and to minimize costs of remediation

The effects of prioritize inspections on occupational health hazards control in workplaces in Iran.

Science.gov (United States)

Sadeghi, Fatemah; Bahrami, Abdolrahman; Fatemi, Farin

2014-01-01

Iran, a newly industrializing country in Middle East, has a workforce of 25 million people. Most employees are working in agriculture, manufacturing, services, construction, commerce sectors, carpet weaving and mining. This article aims to explore the improvement of occupational harmful agents in workplaces due to implement "prioritize inspections". In 2012, the system of "prioritize inspections "was defined for surveillance on enterprises replace of routine inspection. From this system, the enterprises classified on four groups based on health hazards and enterprises with high risk were under more surveillance. The information about each enterprise was collected by health centers, in five provinces and reported by a recommended form to Centre of Environmental and Occupational Health (CEOH). At this program, the inspections from high and medium hazards were increased in all of provinces. The results showed there was a significant difference between the control of health hazards in before and after beginning of "prioritize inspections"(P=0.048). The control of noise, fumes and providing of proper illumination increased from 8 to 10%, 9 to 9.5%, 12.9 to 15.4%, respectively, at under study provinces in 2012 compared to 2011. The surveillance based on "prioritize inspections" increased the quality of occupational health inspections that causes to prevent occupational health diseases.

Managing the Department of Energy's hazardous and mixed defense wastes

International Nuclear Information System (INIS)

Daly, G.H.; Sharples, F.E.; McBrayer, J.F.

1986-04-01

Like other large and complex industries, the nuclear weapons programs produce hazardous chemical wastes, many of which require special handling for the protection of health, safety, and the environment. This requires the interaction of a multiplicity of organizational entities. The HAZWRAP was established to provide centralized planning and technical support for DP RCRA- and CERCLA-related activities. The benefits of a centralized program integrator include DP-wide consistency in regulatory compliance, effective setting and execution of priorities, and development of optimal long-term waste management strategies for the DP complex

Coastal Flood Hazard Composite Layer for the Coastal Flood Exposure Mapper

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — This is a map service for the Coastal Flood Hazard Composite dataset. This dataset was created by combining hazard zones from the following datasets: FEMA V zones,...

Hazardous and mixed waste transportation program

International Nuclear Information System (INIS)

Hohnstreiter, G.F.; Glass, R.E.; McAllaster, M.E.; Nigrey, P.J.; Trennel, A.J.; Yoshimura, H.R.

1993-01-01

Sandia National Laboratories (SNL) has developed a program to address the packaging needs associated with the transport of hazardous and mixed waste during the United States' Department of Energy (DOE) remediation efforts. The program addresses the technology needs associated with the transport of materials which have components that are radioactive and chemically hazardous. The mixed waste transportation activities focus on on-site specific applications of technology to the transport of hazardous and mixed wastes. These activities were identified at a series of DOE-sponsored workshops. These activities will be composed of the following: (1) packaging concepts, (2) chemical compatibility studies, and (3) systems studies. This paper will address activities in each of these areas. (J.P.N.)

Hazardous and Mixed Waste Transportation Program

International Nuclear Information System (INIS)

Hohnstreiter, G.F.; Glass, R.E.; McAllaster, M.E.; Nigrey, P.J.; Trennel, A.J.; Yoshimura, H.R.

1991-01-01

Sandia National Laboratories (SNL) has developed a program to address the packaging needs associated with the transport of hazardous and mixed waste during the United States' Department of Energy (DOE) remediation efforts. The program addresses the technology needs associated with the transport of materials which have components that are radioactive and chemically hazardous. The mixed waste transportation activities focus on on-site specific applications of technology to the transport of hazardous and mixed wastes. These activities were identified at a series of DOE-sponsored workshops. These activities will be composed of the following: (1) packaging concepts, (2) chemical compatibility studies, and (3) systems studies. This paper will address activities in each of these areas

76 FR 74709 - Hazardous Waste Management System; Identification and Listing of Hazardous Waste; Final Exclusion

Science.gov (United States)

2011-12-01

..., including any sludge, spill residue, ash, emission control dust, or leachate, remains a hazardous waste... water for use as a cleaning agent. The slop oil waste is thereby diluted and hazardous constituents are... separation sludges that are listed as hazardous wastes due to benzene, benzo(a)pyrene, chrysene, lead and...

Chemical dependency: An occupational hazard in the field of anaesthesia

International Nuclear Information System (INIS)

Ismail, S.

2010-01-01

The medical personnel are vulnerable to substance abuse and dependence due to ready access to substance of abuse. Addiction is considered as an occupational hazard for those involved in the practice of anaesthesia for the same reason. Substance abuse is defined as a psychosocial biogenetic disease, which results from dynamic interplay between a susceptible host and favourable environment. According to the fifth and the last National Survey on Drug Abuse (NSDA) in 1993 by Pakistan Narcotic Control, there are nearly three million drug dependants Review Article Chemical dependency: An occupational hazard in the field of anaesthesia Samina Ismail Department of Anaesthesia, Aga Khan University Hospital, Karachi. in Pakistan, but no data is available to determine the prevalence among medical or anaesthesia personnel. In order to handle the rising trend of chemical abuse, we need to have more surveys and studies on this subject, written policy and educational programme in postgraduate training with proper control and frequent checking of narcotic dispensing. Reporting of drug abuse and rehabilitation of affected doctors are areas which need to be worked upon. (author)

Hazardous waste management in the Pacific basin

Energy Technology Data Exchange (ETDEWEB)

Cirillo, R.R.; Chiu, S.; Chun, K.C.; Conzelmann, G. [Argonne National Lab., IL (United States); Carpenter, R.A.; Indriyanto, S.H. [East-West Center, Honolulu, HI (United States)

1994-11-01

Hazardous waste control activities in Asia and the Pacific have been reviewed. The review includes China (mainland, Hong Kong, and Taiwan), Indonesia, Korea, Malaysia, Papua New Guinea, the Philippines, Singapore, and Thailand. It covers the sources of hazardous waste, the government structure for dealing with hazardous waste, and current hazardous waste control activities in each country. In addition, the hazardous waste program activities of US government agencies, US private-sector organizations, and international organizations are reviewed. The objective of these reviews is to provide a comprehensive picture of the current hazardous waste problems and the waste management approaches being used to address them so that new program activities can be designed more efficiently.

FEMA Hazard Mitigation Grant Program - Property Acquisitions

Data.gov (United States)

Department of Homeland Security — HMGP provides grants to states and local governments to implement long-term hazard mitigation measures after a major disaster declaration. The HMGP is one of three...

Robots, systems, and methods for hazard evaluation and visualization

Science.gov (United States)

Nielsen, Curtis W.; Bruemmer, David J.; Walton, Miles C.; Hartley, Robert S.; Gertman, David I.; Kinoshita, Robert A.; Whetten, Jonathan

2013-01-15

A robot includes a hazard sensor, a locomotor, and a system controller. The robot senses a hazard intensity at a location of the robot, moves to a new location in response to the hazard intensity, and autonomously repeats the sensing and moving to determine multiple hazard levels at multiple locations. The robot may also include a communicator to communicate the multiple hazard levels to a remote controller. The remote controller includes a communicator for sending user commands to the robot and receiving the hazard levels from the robot. A graphical user interface displays an environment map of the environment proximate the robot and a scale for indicating a hazard intensity. A hazard indicator corresponds to a robot position in the environment map and graphically indicates the hazard intensity at the robot position relative to the scale.

Quality assurance for packaging of radioactive and hazardous materials

International Nuclear Information System (INIS)

Gustafson, L.D.

1986-01-01

The Department of Energy (DOE) has required for many years that quality assurance programs be established and implemented for the packaging of radioactive and hazardous materials. This paper identifies various requirement principles and related actions involved in establishing effective quality assurance for packaging of radioactive and hazardous materials. A primary purpose of these quality assurance program activities is to provide assurance that the packaging and transportation of hazardous materials, which includes radioactive and fissile materials, are in conformance with appropriate governmental regulations. Applicable regulations include those issued by the Nuclear Regulatory Commission (NRC), the Department of Transportation (DOT), and the Environmental Protection Agency (EPA). DOE Order 5700.6A establishes that quality assurance requirements are to be applied in accordance with national consensus standards where suitable ones are available. In the nuclear area, ANSI/ASME NQA-1 is the preferred standard

Occupational health hazards in mining: an overview

Energy Technology Data Exchange (ETDEWEB)

Donoghue, A.M. [Alcoa World Alumina Australia, Perth, WA (Australia)

2004-08-01

This review article outlines the physical, chemical, biological, ergonomic and psychosocial occupational health hazards of mining and associated metallurgical processes. Mining remains an important industrial sector in many parts of the world and although substantial progress has been made in the control of occupational health hazards, there remains room for further risk reduction. This applies particularly to traumatic injury hazards, ergonomic hazards and noise. Vigilance is also required to ensure exposures to coal dust and crystalline silica remain effectively controlled.

78 FR 60755 - Hazardous Materials: Enhanced Enforcement Procedures-Resumption of Transportation

Science.gov (United States)

2013-10-02

... material,'' we envisioned etiological agents, such as biological products, infectious substances, medical... accidents or incidents involving the transportation of hazardous material. In order to achieve a uniform... DEPARTMENT OF TRANSPORTATION Pipeline and Hazardous Materials Safety Administration 49 CFR Part...

A Guide to the Application of Probability Risk Assessment Methodology and Hazard Risk Frequency Criteria as a Hazard Control for the Use of the Mobile Servicing System on the International Space Station

Science.gov (United States)

D'silva, Oneil; Kerrison, Roger

2013-09-01

A key feature for the increased utilization of space robotics is to automate Extra-Vehicular manned space activities and thus significantly reduce the potential for catastrophic hazards while simultaneously minimizing the overall costs associated with manned space. The principal scope of the paper is to evaluate the use of industry standard accepted Probability risk/safety assessment (PRA/PSA) methodologies and Hazard Risk frequency Criteria as a hazard control. This paper illustrates the applicability of combining the selected Probability risk assessment methodology and hazard risk frequency criteria, in order to apply the necessary safety controls that allow for the increased use of the Mobile Servicing system (MSS) robotic system on the International Space Station. This document will consider factors such as component failure rate reliability, software reliability, and periods of operation and dormancy, fault tree analyses and their effects on the probability risk assessments. The paper concludes with suggestions for the incorporation of existing industry Risk/Safety plans to create an applicable safety process for future activities/programs

Savannah River Plant Separations Department mixed waste program

International Nuclear Information System (INIS)

Wierzbicki, W.M.

1988-01-01

The Department of Energy's (DOE) Savannah River Plant (SRP) generates radioactive and mixed waste as a result of the manufacture of nuclear material for the national defense program. The radioactive portion of the mixed waste and all nonhazardous radioactive wastes would continue to be regulated by DOE under the Atomic Energy Act. The Separations Department is the largest generator of solid radioactive waste at the Savannah River Plant. Over the last three years, the Separations Department has developed and implemented a program to characterize candidate mixed-waste streams. The program consisted of facility personnel interviews, a waste-generation characterization program and waste testing to determine whether a particular waste form was hazardous. The Separations Department changed waste-handling practices and procedures to meet the requirements of the generator standards. For each Separation Department Facility, staging areas were established, inventory and reporting requirements were developed, operating procedures were revised to ensure proper waste handling, and personnel were provided hazardous waste training. To emphasize the importance of the new requirements, a newsletter was developed and issued to all Separations supervisory personnel

Environmental Hazards and Mud Volcanoes in Romania

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Romania, an eastern European country, is severely affected by a variety of natural hazards. These include frequent earthquakes, floods, landslides, soil erosion, and...

Natural phenomena hazards, Hanford Site, south central Washington

International Nuclear Information System (INIS)

Tallman, A.M.

1996-01-01

This document presents the natural phenomena hazard (NPH) loads for use in implementing DOE Order 5480.28, Natural Phenomena Hazards Mitigation, at the Hanford Site in south-central Washington State. The purpose of this document is twofold: (1) summarize the NPH that are important to the design and evaluation of structures, systems, and components at the Hanford Site; (2) develop the appropriate natural phenomena loads for use in the implementation of DOE Order 5480.28. The supporting standards, DOE-STD-1020-94, Natural Phenomena Hazards Design and Evaluation Criteria for Department of Energy Facilities (DOE 1994a); DOE-STD-1022-94, Natural Phenomena Hazards Site Characteristics Criteria (DOE 1994b); and DOE-STD-1023-95, Natural Phenomena Hazards Assessment Criteria (DOE 1995) are the basis for developing the NPH loads

Controlling hazardous energy sources (lockout/tagout)

Science.gov (United States)

Dominguez, Manuel B.

1991-10-01

The minimum requirements as established by the Occupational Safety and Health Administration (OSHA) standard 29 CFR 1910.147 are discussed for preventing the unexpected operation of equipment or release of energy which could cause injury to personnel, damage to equipment, harm to the environment, or loss or compromise of test data. Safety requirements both for government and contractor personnel are explained for potentially hazardous energy sources during work operations at LeRC (Cleveland and Plum Brook Stations). Basic rules are presented to ensure protection against harmful exposures, and baseline implementation requirements are discussed from which detailed lockout/tagout procedures can be developed for individual equipment items. Examples of energy sources covered by this document include electrical, pneumatic, mechanical, chemical, cryogenic, thermal, spring tension/compression suspended or moving loads, and other potentially hazardous sources. Activities covered by this standard include, but are not limited to, construction, maintenance, installation, calibration, inspection, cleaning, or repair.

The radiological hazard of plutonium isotopes and specific plutonium mixtures

International Nuclear Information System (INIS)

Heindel, G.; Clow, J.; Inkret, W.; Miller, G.

1995-11-01

The US Department of Energy defines the hazard categories of its nuclear facilities based upon the potential for accidents to have significant effects on specific populations and the environment. In this report, the authors consider the time dependence of hazard category 2 (significant on-site effects) for facilities with inventories of plutonium isotopes and specific weapons-grade and heat-source mixtures of plutonium isotopes. The authors also define relative hazard as the reciprocal of the hazard category 2 threshold value and determine its time dependence. The time dependence of both hazard category 2 thresholds and relative hazards are determined and plotted for 10,000 years to provide useful information for planning long-term storage or disposal facilities

Hazardous waste shipment data collection from DOE sites

International Nuclear Information System (INIS)

Page, L.A.; Kirkpatrick, T.D.; Stevens, L.

1992-01-01

Past practices at the US Department of Energy (DOE) sites for offsite release of hazardous waste are being reviewed to determine if radioactively contaminated hazardous wastes were released to commercial treatment, storage, and disposal facilities. Records indicating the presence of radioactivity in waste shipped to and treated at a commercial incineration facility led to a ban on offsite hazardous waste shipments and investigation of past practices for offsite release of hazardous waste from the DOE sites. A House of Representatives Interior and Insular Affairs Committee oversight hearing on potentially contaminated waste shipments to commercial facilities concluded that the main issue was the lack of a uniform national standard to govern disposal of mixed waste

DISAMENITY HAZARDS AND RENTAL VALUES IN SURULERE ...

African Journals Online (AJOL)

Osondu

2010-02-13

Feb 13, 2010 ... This current study identifies and evaluates the various risk elements and hazards ... of Nigeria and further concludes that the State government organise ... 2Department of Estate Management, Obafemi Awolowo University,.

The impact of a home visitation programme on household hazards associated with unintentional childhood injuries: a randomised controlled trial.

Science.gov (United States)

Odendaal, Willem; van Niekerk, Ashley; Jordaan, Esme; Seedat, Mohamed

2009-01-01

The continued high mortality and morbidity rates for unintentional childhood injuries remain a public health concern. This article reports on the influence of a home visitation programme (HVP) on household hazards associated with unintentional childhood injuries in a South African low-income setting. A randomised controlled trial (n=211 households) was conducted in a South African informal settlement. Community members were recruited and trained as paraprofessional visitors. Four intervention visits were conducted over 3 months, focusing on child development, and the prevention of burn, poison, and fall injuries. The HVP, a multi-component intervention, included educational inputs, provision of safety devices, and an implicit enforcement strategy. The intervention effect (IE) was measured with a standardised risk assessment index that compared post-intervention scores for intervention and control households. A significant reduction was observed in the hazards associated with electrical and paraffin appliances, as well as in hazards related to poisoning. Non-significant changes were observed for burn safety household practices and fall injury hazards. This study confirmed that a multi-component HVP effectively reduced household hazards associated with electrical and paraffin appliances and poisoning among children in a low-income South African setting.

F-Area Hazardous Waste Management Facility Corrective Action Report - Third and Fourth Quarter 1999, Volumes I and II

International Nuclear Information System (INIS)

Chase, J.

2000-01-01

Savannah River Site (SRS) monitors groundwater quality at the F-Area Hazardous Waste management Facility (HWMF) and provides results of this monitoring to the South Carolina Department of Health and Environmental Control (SCDHEC) semiannually as required by the Resource Conservation and Recovery Act (RCRA) permit. SRS also performs monthly sampling of the Wastewater Treatment Unit (WTU) effluent in accordance with Section C of the Underground Injection Control (UIC) application

Industrial hazard and safety handbook

CERN Document Server

King, Ralph W

1979-01-01

Industrial Hazard and Safety Handbook (Revised Impression) describes and exposes the main hazards found in industry, with emphasis on how these hazards arise, are ignored, are identified, are eliminated, or are controlled. These hazard conditions can be due to human stresses (for example, insomnia), unsatisfactory working environments, as well as secret industrial processes. The book reviews the cost of accidents, human factors, inspections, insurance, legal aspects, planning for major emergencies, organization, and safety measures. The text discusses regulations, codes of practice, site layou

Hazardous drinking and its association with homelessness among veterans in care.

Science.gov (United States)

Ghose, T; Fiellin, D A; Gordon, A J; Metraux, S; Goetz, M B; Blackstock, O; McInnes, K; Rodriguez-Barradas, M C; Justice, A C

2013-09-01

While scholarship on alcohol use and homelessness has focused on the impact of alcohol abuse and dependence, little is known about the effects of lower levels of misuse such as hazardous use. Veterans receiving care in the Department of Veterans Affairs Health Care System (VA) constitute a population that is vulnerable to alcohol misuse and homelessness. This research examines the effects of hazardous drinking on homelessness in the Veterans Aging Cohort Study, a sample of 2898 older veterans (mean age=50.2), receiving care in 8 VAs across the country. Logistic regression models examined the associations between (1) hazardous drinking at baseline and homelessness at 1-year follow-up, (2) transitions into and out of hazardous drinking from baseline to follow-up and homelessness at follow-up, and (3) transitioning to hazardous drinking and transitioning to homelessness from baseline to follow-up during that same time-period. After controlling for other correlates including alcohol dependence, hazardous drinking at baseline increased the risk of homelessness at follow-up (adjusted odds ratio [AOR]=1.39, 95% confidence interval [CI]=1.02, 1.88). Transitioning to hazardous drinking more than doubled the risk of homelessness at follow-up (AOR=2.42, 95% CI=1.41, 4.15), while more than doubling the risk of transitioning from being housed at baseline to being homeless at follow-up (AOR=2.49, 95% CI=1.30, 4.79). Early intervention that seeks to prevent transitioning into hazardous drinking could increase housing stability among veterans. Brief interventions which have been shown to be effective at lower levels of alcohol use should be implemented with veterans in VA care. Published by Elsevier Ireland Ltd.

2013 Los Alamos National Laboratory Hazardous Waste Minimization Report

Energy Technology Data Exchange (ETDEWEB)

Salzman, Sonja L. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); English, Charles J. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2015-08-24

Waste minimization and pollution prevention are inherent goals within the operating procedures of Los Alamos National Security, LLC (LANS). The US Department of Energy (DOE) and LANS are required to submit an annual hazardous waste minimization report to the New Mexico Environment Department (NMED) in accordance with the Los Alamos National Laboratory (LANL or the Laboratory) Hazardous Waste Facility Permit. The report was prepared pursuant to the requirements of Section 2.9 of the LANL Hazardous Waste Facility Permit. This report describes the hazardous waste minimization program (a component of the overall Waste Minimization/Pollution Prevention [WMin/PP] Program) administered by the Environmental Stewardship Group (ENV-ES). This report also supports the waste minimization and pollution prevention goals of the Environmental Programs Directorate (EP) organizations that are responsible for implementing remediation activities and describes its programs to incorporate waste reduction practices into remediation activities and procedures. LANS was very successful in fiscal year (FY) 2013 (October 1-September 30) in WMin/PP efforts. Staff funded four projects specifically related to reduction of waste with hazardous constituents, and LANS won four national awards for pollution prevention efforts from the National Nuclear Security Administration (NNSA). In FY13, there was no hazardous, mixedtransuranic (MTRU), or mixed low-level (MLLW) remediation waste generated at the Laboratory. More hazardous waste, MTRU waste, and MLLW was generated in FY13 than in FY12, and the majority of the increase was related to MTRU processing or lab cleanouts. These accomplishments and analysis of the waste streams are discussed in much more detail within this report.

Frequency Analysis of Aircraft hazards for License Application

International Nuclear Information System (INIS)

K. Ashley

2006-01-01

The preclosure safety analysis for the monitored geologic repository at Yucca Mountain must consider the hazard that aircraft may pose to surface structures. Relevant surface structures are located beneath the restricted airspace of the Nevada Test Site (NTS) on the eastern slope of Yucca Mountain, near the North Portal of the Exploratory Studies Facility Tunnel (Figure 1). The North Portal is located several miles from the Nevada Test and Training Range (NTTR), which is used extensively by the U.S. Air Force (USAF) for training and test flights (Figure 1). The NTS airspace, which is controlled by the U.S. Department of Energy (DOE) for NTS activities, is not part of the NTTR. Agreements with the DOE allow USAF aircraft specific use of the airspace above the NTS (Reference 2.1.1 [DIRS 103472], Section 3.1.1 and Appendix A, Section 2.1; and Reference 2.1.2 [DIRS 157987], Sections 1.26 through 1.29). Commercial, military, and general aviation aircraft fly within several miles to the southwest of the repository site in the Beatty Corridor, which is a broad air corridor that runs approximately parallel to U.S. Highway 95 and the Nevada-California border (Figure 2). These aircraft and other aircraft operations are identified and described in ''Identification of Aircraft Hazards'' (Reference 2.1.3, Sections 6 and 8). The purpose of this analysis is to estimate crash frequencies for aircraft hazards identified for detailed analysis in ''Identification of Aircraft Hazards'' (Reference 2.1.3, Section 8). Reference 2.1.3, Section 8, also identifies a potential hazard associated with electronic jamming, which will be addressed in this analysis. This analysis will address only the repository and not the transportation routes to the site. The analysis is intended to provide the basis for: (1) Categorizing event sequences related to aircraft hazards; (2) Identifying design or operational requirements related to aircraft hazards

Frequency Analysis of Aircraft hazards for License Application

Energy Technology Data Exchange (ETDEWEB)

K. Ashley

2006-10-24

The preclosure safety analysis for the monitored geologic repository at Yucca Mountain must consider the hazard that aircraft may pose to surface structures. Relevant surface structures are located beneath the restricted airspace of the Nevada Test Site (NTS) on the eastern slope of Yucca Mountain, near the North Portal of the Exploratory Studies Facility Tunnel (Figure 1). The North Portal is located several miles from the Nevada Test and Training Range (NTTR), which is used extensively by the U.S. Air Force (USAF) for training and test flights (Figure 1). The NTS airspace, which is controlled by the U.S. Department of Energy (DOE) for NTS activities, is not part of the NTTR. Agreements with the DOE allow USAF aircraft specific use of the airspace above the NTS (Reference 2.1.1 [DIRS 103472], Section 3.1.1 and Appendix A, Section 2.1; and Reference 2.1.2 [DIRS 157987], Sections 1.26 through 1.29). Commercial, military, and general aviation aircraft fly within several miles to the southwest of the repository site in the Beatty Corridor, which is a broad air corridor that runs approximately parallel to U.S. Highway 95 and the Nevada-California border (Figure 2). These aircraft and other aircraft operations are identified and described in ''Identification of Aircraft Hazards'' (Reference 2.1.3, Sections 6 and 8). The purpose of this analysis is to estimate crash frequencies for aircraft hazards identified for detailed analysis in ''Identification of Aircraft Hazards'' (Reference 2.1.3, Section 8). Reference 2.1.3, Section 8, also identifies a potential hazard associated with electronic jamming, which will be addressed in this analysis. This analysis will address only the repository and not the transportation routes to the site. The analysis is intended to provide the basis for: (1) Categorizing event sequences related to aircraft hazards; (2) Identifying design or operational requirements related to aircraft hazards.

Toward risk assessment 2.0: Safety supervisory control and model-based hazard monitoring for risk-informed safety interventions

International Nuclear Information System (INIS)

Favarò, Francesca M.; Saleh, Joseph H.

2016-01-01

Probabilistic Risk Assessment (PRA) is a staple in the engineering risk community, and it has become to some extent synonymous with the entire quantitative risk assessment undertaking. Limitations of PRA continue to occupy researchers, and workarounds are often proposed. After a brief review of this literature, we propose to address some of PRA's limitations by developing a novel framework and analytical tools for model-based system safety, or safety supervisory control, to guide safety interventions and support a dynamic approach to risk assessment and accident prevention. Our work shifts the emphasis from the pervading probabilistic mindset in risk assessment toward the notions of danger indices and hazard temporal contingency. The framework and tools here developed are grounded in Control Theory and make use of the state-space formalism in modeling dynamical systems. We show that the use of state variables enables the definition of metrics for accident escalation, termed hazard levels or danger indices, which measure the “proximity” of the system state to adverse events, and we illustrate the development of such indices. Monitoring of the hazard levels provides diagnostic information to support both on-line and off-line safety interventions. For example, we show how the application of the proposed tools to a rejected takeoff scenario provides new insight to support pilots’ go/no-go decisions. Furthermore, we augment the traditional state-space equations with a hazard equation and use the latter to estimate the times at which critical thresholds for the hazard level are (b)reached. This estimation process provides important prognostic information and produces a proxy for a time-to-accident metric or advance notice for an impending adverse event. The ability to estimate these two hazard coordinates, danger index and time-to-accident, offers many possibilities for informing system control strategies and improving accident prevention and risk mitigation

46 CFR 151.03-30 - Hazardous material.

Science.gov (United States)

2010-10-01

... hazardous material means a liquid material or substance that is— (a) Flammable or combustible; (b) Designated a hazardous substance under section 311(b) of the Federal Water Pollution Control Act (33 U.S.C... Agency designates hazardous substances in 40 CFR Table 116.4A. The Coast Guard designates hazardous...

[Investigation of noise hazards and hearing status of workers in outdoor quarries].

Science.gov (United States)

Zhang, Guoying; Tang, Zhifeng; Yao, Yongping; Wang, Haiying

2014-08-01

To investigate the noise hazards in open quarries and to provide a basis for further control of noise hazards. An investigation was performed during 2010 to 2011 among all open quarries in Deqing County of Zhejiang Province, China. The investigation included basic information of the quarries, the occupational health situation and noise intensity at the workplace, and the hearing loss of workers exposed to noise in quarry enterprises. The hearing test results were evaluated based on the Diagnostic criteria of occupational noise-induced hearing loss (GBZ 49-2007). A total of 25 enterprises with open quarries were investigated, of which only 30.4% (17/56) workplaces met the national standard. The median noise level was 92.5 dB (A). Fifty-four (10.6%) out of 508 workers in the 25 enterprises were diagnosed with binaural hearing loss in the initial physical examination, with 18.3% (93/508) under surveillance. The rate of normal hearing among crushing workers, mechanists, drilling workers, and blasting workers ranged between 27.6% and 41.4%, which was significantly lower than that among workers exposed to slight noise hazards (80.0%) or other workers (63.7%) (P drilling workers, and blasting workers most seriously jeopardized. Among crushing workers, those working in the first-line or unprotected second?line positions suffered more than the others. Further measures should be taken by the supervision department and the enterprises to control the noise hazards in open quarries.

Hazardous Chemicals

Centers for Disease Control (CDC) Podcasts

2007-04-10

Chemicals are a part of our daily lives, providing many products and modern conveniences. With more than three decades of experience, The Centers for Disease Control and Prevention (CDC) has been in the forefront of efforts to protect and assess people's exposure to environmental and hazardous chemicals. This report provides information about hazardous chemicals and useful tips on how to protect you and your family from harmful exposure.  Created: 4/10/2007 by CDC National Center for Environmental Health.   Date Released: 4/13/2007.

Information requirements for the Department of Energy Defense Programs' hazardous and mixed wastes

International Nuclear Information System (INIS)

Herron, S.A.

1987-01-01

This document contains viewgraphs from a presentation made to the DOE Low-Level Waste Management Conference in Denver, Colorado. The presentation described information and data base systems that describe hazardous and mixed waste treatment, storage, and disposal

Control of dust hazards in mines

Energy Technology Data Exchange (ETDEWEB)

Sukhanov, V V

1981-09-01

This paper analyzes health hazards associated with air pollution by respirable coal dust which causes pneumoconioses. The following directions in pneumoconioses prevention are discussed: improved protective systems (e.g. respirators), mining schemes optimized from a health hazards point of view, correct determination of the maximum permissible level of respirable dusts, reducing working time. Safety regulations in the USSR on the critical amount of coal dust in the miner respiratory system are insufficient as the 20 g limit is too high and does not guarantee safety. Using regression analysis influence of the factors which cause pneumoconioses is analyzed. This influence is described by an equation which considers the following factors: number of shifts associated with contact of a miner with coal dusts, dust concentration in mine air, amount of air with coal dust being respirated, miner's age, years as miner, coal rank. It is stated that use of the proposed equation (derived by computer calculations) permits the safe working time to be correctly determined considering all factors which cause pneumoconioses.

Modified Hazard Ranking System/Hazard Ranking System for sites with mixed radioactive and hazardous wastes: Software documentation

Energy Technology Data Exchange (ETDEWEB)

Stenner, R.D.; Peloquin, R.A.; Hawley, K.A.

1986-11-01

The mHRS/HRS software package was developed by the Pacific Northwest Laboratory (PNL) under contract with the Department of Energy (DOE) to provide a uniform method for DOE facilities to use in performing their Conservation Environmental Response Compensation and Liability Act (CERCLA) Phase I Modified Hazard Ranking System or Hazard Ranking System evaluations. The program is designed to remove the tedium and potential for error associated with the performing of hand calculations and the interpreting of information on tables and in reference books when performing an evaluation. The software package is designed to operate on a microcomputer (IBM PC, PC/XT, or PC/AT, or a compatible system) using either a dual floppy disk drive or a hard disk storage system. It is written in the dBASE III language and operates using the dBASE III system. Although the mHRS/HRS software package was developed for use at DOE facilities, it has direct applicability to the performing of CERCLA Phase I evaluations for any facility contaminated by hazardous waste. The software can perform evaluations using either the modified hazard ranking system methodology developed by DOE/PNL, the hazard ranking system methodology developed by EPA/MITRE Corp., or a combination of the two. This document is a companion manual to the mHRS/HRS user manual. It is intended for the programmer who must maintain the software package and for those interested in the computer implementation. This manual documents the system logic, computer programs, and data files that comprise the package. Hardware and software implementation requirements are discussed. In addition, hand calculations of three sample situations (problems) with associated computer runs used for the verification of program calculations are included.

Modified Hazard Ranking System/Hazard Ranking System for sites with mixed radioactive and hazardous wastes: Software documentation

International Nuclear Information System (INIS)

Stenner, R.D.; Peloquin, R.A.; Hawley, K.A.

1986-11-01

The mHRS/HRS software package was developed by the Pacific Northwest Laboratory (PNL) under contract with the Department of Energy (DOE) to provide a uniform method for DOE facilities to use in performing their Conservation Environmental Response Compensation and Liability Act (CERCLA) Phase I Modified Hazard Ranking System or Hazard Ranking System evaluations. The program is designed to remove the tedium and potential for error associated with the performing of hand calculations and the interpreting of information on tables and in reference books when performing an evaluation. The software package is designed to operate on a microcomputer (IBM PC, PC/XT, or PC/AT, or a compatible system) using either a dual floppy disk drive or a hard disk storage system. It is written in the dBASE III language and operates using the dBASE III system. Although the mHRS/HRS software package was developed for use at DOE facilities, it has direct applicability to the performing of CERCLA Phase I evaluations for any facility contaminated by hazardous waste. The software can perform evaluations using either the modified hazard ranking system methodology developed by DOE/PNL, the hazard ranking system methodology developed by EPA/MITRE Corp., or a combination of the two. This document is a companion manual to the mHRS/HRS user manual. It is intended for the programmer who must maintain the software package and for those interested in the computer implementation. This manual documents the system logic, computer programs, and data files that comprise the package. Hardware and software implementation requirements are discussed. In addition, hand calculations of three sample situations (problems) with associated computer runs used for the verification of program calculations are included

An approach to quantitate and control the mutagenic hazards of environmental chemical and radioactive pollutants

International Nuclear Information System (INIS)

Murthy, M.S.S.

1977-01-01

Human population, both at the occupational and non-occupational levels, is exposed to the environment polluted by man-made chemicals and radiation sources. The parameters required for quantitating mutagenic hazards of any agent are listed and it has been pointed out that though sufficient information of this nature is available in the case of radiations, it is almost impossible to collect similar information for chemical substances due to their number running into astronomical figures. A short-cut approach, therefore, is suggested to quantitate and control the mutagenic hazards of these pollutants. It is to express the mutagenic hazards of a chemical substance in terms of equivalent radiation units. The unit proposed for this purpose is called as Rem-Equivalent Chemical (REC). Total mutagenic burden to the society should take account of exposure from both chemicals and radiations. Advantages and limitation of this approach are discussed. (M.G.B.)

Hazards assessment for the INEL Landfill Complex

International Nuclear Information System (INIS)

Knudsen, J.K.; Calley, M.B.

1994-02-01

This report documents the hazards assessment for the INEL Landfill Complex (LC) located at the Idaho National Engineering Laboratory, which is operated by EG ampersand G Idaho, Inc., for the US Department of Energy (DOE). The hazards assessment was performed to ensure that this facility complies with DOE and company requirements pertaining to emergency planning and preparedness for operational emergencies. DOE Order 5500.3A requires that a facility-specific hazards assessment be performed to provide the technical basis for facility emergency planning efforts. This hazards assessment was conducted in accordance with DOE Headquarters and the DOE Idaho Operations Office (DOE-ID) guidance to comply with DOE Order 5500.3A. The hazards assessment identifies and analyzes the hazards that are significant enough to warrant consideration in a facility's operational emergency management program. The area surrounding the LC, the buildings and structures at the LC, and the processes that are used at the LC are described in this report. All hazardous materials, both radiological and nonradiological, at the LC were identified and screened against threshold quantities according to DOE Order 5500.3A guidance. Asbestos at the Asbestos Pit was the only hazardous material that exceeded its specified threshold quantity. However, the type of asbestos received and the packaging practices used are believed to limit the potential for an airborne release of asbestos fibers. Therefore, in accordance with DOE Order 5500.3A guidance, no further hazardous material characterization or analysis was required for this hazards assessment

Hazards assessment for the INEL Landfill Complex

Energy Technology Data Exchange (ETDEWEB)

Knudsen, J.K.; Calley, M.B.

1994-02-01

This report documents the hazards assessment for the INEL Landfill Complex (LC) located at the Idaho National Engineering Laboratory, which is operated by EG&G Idaho, Inc., for the US Department of Energy (DOE). The hazards assessment was performed to ensure that this facility complies with DOE and company requirements pertaining to emergency planning and preparedness for operational emergencies. DOE Order 5500.3A requires that a facility-specific hazards assessment be performed to provide the technical basis for facility emergency planning efforts. This hazards assessment was conducted in accordance with DOE Headquarters and the DOE Idaho Operations Office (DOE-ID) guidance to comply with DOE Order 5500.3A. The hazards assessment identifies and analyzes the hazards that are significant enough to warrant consideration in a facility`s operational emergency management program. The area surrounding the LC, the buildings and structures at the LC, and the processes that are used at the LC are described in this report. All hazardous materials, both radiological and nonradiological, at the LC were identified and screened against threshold quantities according to DOE Order 5500.3A guidance. Asbestos at the Asbestos Pit was the only hazardous material that exceeded its specified threshold quantity. However, the type of asbestos received and the packaging practices used are believed to limit the potential for an airborne release of asbestos fibers. Therefore, in accordance with DOE Order 5500.3A guidance, no further hazardous material characterization or analysis was required for this hazards assessment.

US Department of Energy radiological control manual

International Nuclear Information System (INIS)

1994-04-01

This manual establishes practices for the conduct of Department of Energy radiological control activities. The Manual states DOE's positions and views on the best courses of action currently available in the area of radiological controls. Accordingly, the provisions in the Manual should be viewed by contractors as an acceptable technique, method or solution for fulfilling their duties and responsibilities. This Manual shall be used by DOE in evaluating the performance of its contractors. This Manual is not a substitute for Regulations; it is intended to be consistent with all relevant statutory and regulatory requirements and shall be revised whenever necessary to ensure such consistency. Some of the Manual provisions, however, challenge the user to go well beyond minimum requirements. Following the course of action delineated in the Manual will result in achieving and surpassing related statutory or regulatory requirements

30 CFR 56.9310 - Chute hazards.

Science.gov (United States)

2010-07-01

... Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Loading, Hauling, and Dumping Safety... hangups shall be experienced and familiar with the task, know the hazards involved, and use the proper...

30 CFR 57.9310 - Chute hazards.

Science.gov (United States)

2010-07-01

... Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL AND NONMETAL MINES Loading, Hauling, and Dumping... free chute hangups shall be experienced and familiar with the task, know the hazards involved, and use...

Flood Hazard Recurrence Frequencies for the Savannah River Site

International Nuclear Information System (INIS)

Chen, K.F.

2001-01-01

Department of Energy (DOE) regulations outline the requirements for Natural Phenomena Hazard (NPH) mitigation for new and existing DOE facilities. The NPH considered in this report is flooding. The facility-specific probabilistic flood hazard curve defines, as a function of water elevation, the annual probability of occurrence or the return period in years. The facility-specific probabilistic flood hazard curves provide basis to avoid unnecessary facility upgrades, to establish appropriate design criteria for new facilities, and to develop emergency preparedness plans to mitigate the consequences of floods. A method based on precipitation, basin runoff and open channel hydraulics was developed to determine probabilistic flood hazard curves for the Savannah River Site. The calculated flood hazard curves show that the probabilities of flooding existing SRS major facilities are significantly less than 1.E-05 per year

Post-operative endophthalmitis: the application of hazard analysis critical control points (HACCP) to an infection control problem.

Science.gov (United States)

Baird, D R; Henry, M; Liddell, K G; Mitchell, C M; Sneddon, J G

2001-09-01

Hazard analysis critical control points (HACCP) is a quality assurance system widely used in the food industry to ensure safety. We adopted the HACCP approach when conventional infection control measures had failed to solve an ongoing problem with an increased incidence of postoperative endophthalmitis, and our ophthalmology unit was threatened with permanent cessation of intraocular surgery. Although time-consuming, the result was an entirely new set of protocols for the care of patients undergoing intraocular surgery, the development of an integrated care pathway, and a comprehensive and robust audit programme, which enabled intraocular surgery to continue in a new spirit of confidence. HACCP methodology has so far been little used in healthcare, but it might be usefully applied to a variety of apparently intractable infection control problems. Copyright 2001 The Hospital Infection Society.

FEMA Hazard Mitigation Assistance Flood Mitigation Assistance (FMA) Data

Data.gov (United States)

Department of Homeland Security — This dataset contains closed and obligated projects funded under the following Hazard Mitigation Assistance (HMA) grant programs: Flood Mitigation Assistance (FMA)....

2016 Los Alamos National Laboratory Hazardous Waste Minimization Report

Energy Technology Data Exchange (ETDEWEB)

Salzman, Sonja L. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); English, Charles Joe [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-12-02

Waste minimization and pollution prevention are goals within the operating procedures of Los Alamos National Security, LLC (LANS). The US Department of Energy (DOE), inclusive of the National Nuclear Security Administration (NNSA) and the Office of Environmental Management, and LANS are required to submit an annual hazardous waste minimization report to the New Mexico Environment Department (NMED) in accordance with the Los Alamos National Laboratory (LANL or the Laboratory) Hazardous Waste Facility Permit. The report was prepared pursuant to the requirements of Section 2.9 of the LANL Hazardous Waste Facility Permit. This report describes the hazardous waste minimization program, which is a component of the overall Pollution Prevention (P2) Program, administered by the Environmental Stewardship Group (EPC-ES). This report also supports the waste minimization and P2 goals of the Associate Directorate of Environmental Management (ADEM) organizations that are responsible for implementing remediation activities and describes its programs to incorporate waste reduction practices into remediation activities and procedures. This report includes data for all waste shipped offsite from LANL during fiscal year (FY) 2016 (October 1, 2015 – September 30, 2016). LANS was active during FY2016 in waste minimization and P2 efforts. Multiple projects were funded that specifically related to reduction of hazardous waste. In FY2016, there was no hazardous, mixed-transuranic (MTRU), or mixed low-level (MLLW) remediation waste shipped offsite from the Laboratory. More non-remediation hazardous waste and MLLW was shipped offsite from the Laboratory in FY2016 compared to FY2015. Non-remediation MTRU waste was not shipped offsite during FY2016. These accomplishments and analysis of the waste streams are discussed in much more detail within this report.

Hazard classification criteria for non-nuclear facilities

International Nuclear Information System (INIS)

Mahn, J.A.; Walker, S.A.

1997-01-01

Sandia National Laboratories' Integrated Risk Management Department has developed a process for establishing the appropriate hazard classification of a new facility or operation, and thus the level of rigor required for the associated authorization basis safety documentation. This process is referred to as the Preliminary Hazard Screen. DOE Order 5481.1B contains the following hazard classification for non-nuclear facilities: high--having the potential for onsite or offsite impacts to large numbers of persons or for major impacts to the environment; moderate--having the potential for considerable onsite impacts but only minor offsite impacts to people or the environment; low--having the potential for only minor onsite and negligible offsite impacts to people or the environment. It is apparent that the application of such generic criteria is more than likely to be fraught with subjective judgment. One way to remove the subjectivity is to define health and safety classification thresholds for specific hazards that are based on the magnitude of the hazard, rather than on a qualitative assessment of possible accident consequences. This paper presents the results of such an approach to establishing a readily usable set of non-nuclear facility hazard classifications

REFUSE DISPOSAL AND ITS ATTENDANT HEALTH HAZARDS: A ...

African Journals Online (AJOL)

Oyem

HAZARDS: A CASE STUDY OF AGBOR, DELTA STATE OF. NIGERIA ... acceptable environmental quality, sound public health, and ... solid waste management and public health, .... by the public relations department of the council to sensitize.

Seismic Ground Motion Hazards with 10 Percent Probability

Data.gov (United States)

Department of Homeland Security — This map layer shows seismic hazard in the United States. The data represent a model showing the probability that ground motion will reach a certain level. This map...

Seismic Ground Motion Hazards with 2 Percent Probability

Data.gov (United States)

Department of Homeland Security — This map layer shows seismic hazard in the United States. The data represent a model showing the probability that ground motion will reach a certain level. This map...

75 FR 35366 - Pipeline Safety: Applying Safety Regulation to All Rural Onshore Hazardous Liquid Low-Stress Lines

Science.gov (United States)

2010-06-22

... DEPARTMENT OF TRANSPORTATION Pipeline and Hazardous Materials Safety Administration 49 CFR Part... Onshore Hazardous Liquid Low-Stress Lines AGENCY: Pipeline and Hazardous Materials Safety Administration... to the risks that hazardous liquid and natural gas pipelines pose to the environment. In the Pipeline...

Hazards assessment for the Waste Experimental Reduction Facility

International Nuclear Information System (INIS)

Calley, M.B.; Jones, J.L. Jr.

1994-01-01

This report documents the hazards assessment for the Waste Experimental Reduction Facility (WERF) located at the Idaho National Engineering Laboratory, which is operated by EG ampersand G Idaho, Inc., for the US Department of Energy (DOE). The hazards assessment was performed to ensure that this facility complies with DOE and company requirements pertaining to emergency planning and preparedness for operational emergencies. DOE Order 5500.3A requires that a facility-specific hazards assessment be performed to provide the technical basis for facility emergency planning efforts. This hazards assessment was conducted in accordance with DOE Headquarters and DOE Idaho Operations Office (DOE-ID) guidance to comply with DOE Order 5500.3A. The hazards assessment identifies and analyzes hazards that are significant enough to warrant consideration in a facility's operational emergency management program. This hazards assessment describes the WERF, the area surrounding WERF, associated buildings and structures at WERF, and the processes performed at WERF. All radiological and nonradiological hazardous materials stored, used, or produced at WERF were identified and screened. Even though the screening process indicated that the hazardous materials could be screened from further analysis because the inventory of radiological and nonradiological hazardous materials were below the screening thresholds specified by DOE and DOE-ID guidance for DOE Order 5500.3A, the nonradiological hazardous materials were analyzed further because it was felt that the nonradiological hazardous material screening thresholds were too high

Hazards assessment for the Waste Experimental Reduction Facility

Energy Technology Data Exchange (ETDEWEB)

Calley, M.B.; Jones, J.L. Jr.

1994-09-19

This report documents the hazards assessment for the Waste Experimental Reduction Facility (WERF) located at the Idaho National Engineering Laboratory, which is operated by EG&G Idaho, Inc., for the US Department of Energy (DOE). The hazards assessment was performed to ensure that this facility complies with DOE and company requirements pertaining to emergency planning and preparedness for operational emergencies. DOE Order 5500.3A requires that a facility-specific hazards assessment be performed to provide the technical basis for facility emergency planning efforts. This hazards assessment was conducted in accordance with DOE Headquarters and DOE Idaho Operations Office (DOE-ID) guidance to comply with DOE Order 5500.3A. The hazards assessment identifies and analyzes hazards that are significant enough to warrant consideration in a facility`s operational emergency management program. This hazards assessment describes the WERF, the area surrounding WERF, associated buildings and structures at WERF, and the processes performed at WERF. All radiological and nonradiological hazardous materials stored, used, or produced at WERF were identified and screened. Even though the screening process indicated that the hazardous materials could be screened from further analysis because the inventory of radiological and nonradiological hazardous materials were below the screening thresholds specified by DOE and DOE-ID guidance for DOE Order 5500.3A, the nonradiological hazardous materials were analyzed further because it was felt that the nonradiological hazardous material screening thresholds were too high.

FEMA Hazard Mitigation Assistance Severe Repetitive Loss (SRL) Data

Data.gov (United States)

Department of Homeland Security — This dataset contains closed and obligated projects funded under the following Hazard Mitigation Assistance (HMA) grant programs: Severe Repetitive Loss (SRL). The...

FEMA Hazard Mitigation Assistance Repetitive Flood Claims (RFC) Data

Data.gov (United States)

Department of Homeland Security — This dataset contains closed and obligated projects funded under the following Hazard Mitigation Assistance (HMA) grant programs: Repetitive Flood Claims (RFC). The...

Building 894 hazards assessment document

International Nuclear Information System (INIS)

Banda, Z.; Williams, M.

1996-07-01

The Department of Energy Order 5500.3A requires facility-specific hazards assessments be prepared, maintained, and used for emergency planning purposes. This hazards assessment document describes the chemical and radiological hazards associated with Building 894. The entire inventory was subjected to the screening criteria for potential airborne impact to onsite and offsite individuals out of which 9 chemicals were kept for further evaluation. The air dispersion model, ALOHA, estimated pollutant concentrations downwind from the source of a release, taking into consideration the toxicological and physical characteristics of the release site, the atmospheric conditions, and the circumstances of the release. The greatest distance at which a postulated facility event will produce consequences exceeding the Early Severe Health Effects threshold is 130 meters. The highest emergency classification is a General Emergency. The Emergency Planning Zone is a nominal 130 meter area that conforms to DOE boundaries and physical/jurisdictional boundaries such as fence lines and streets

Building 6630 hazards assessment document

International Nuclear Information System (INIS)

Williams, M.; Banda, Z.

1996-10-01

The Department of Energy Order 5500.3A requires facility-specific hazards assessments be prepared, maintained, and used for emergency planning purposes. This hazards assessment document describes the chemical and radiological hazards associated with Building 6630. The entire inventory was subjected to the screening criteria for potential airborne impact to onsite and offsite individuals out of which one chemical was kept for further evaluation. The air dispersion model, ALOHA, estimated pollutant concentrations downwind from the source of a release, taking into consideration the toxicological and physical characteristics of the chemical release site, the atmospheric conditions, and the circumstances of the release. The greatest distance at which a postulated facility event will produce consequences exceeding the Early Severe Health Effects threshold is 76 meters. The highest emergency classification is an Alert. The Emergency Planning Zone is a nominal 100 meter area that conforms to DOE boundaries and physical/jurisdictional boundaries such as fence lines and streets

[Cardiovascular risk factor control in a population with longstanding diabetes attending endocrinology departments].

Science.gov (United States)

Comi-Diaz, Cristina; Miralles-García, José M; Cabrerizo, Lucio; Pérez, María; Masramon, Xavier; De Pablos-Velasco, Pedro

2010-12-01

To determine the degree of control of cardiovascular risk factors (CVRF) in a sample of patients with diabetes mellitus (DM) attending Endocrinology and Nutrition Departments in Spain. An epidemiological, cross-sectional, multicenter and observational study involving 41 Departments of Endocrinology and Nutrition in Spain. Each department selected patients with DM with over 10 years of evolution, which were treated in outpatient settings. Demographic, anthropometric, clinical and biochemical data, including medication, were collected for each participant. 1159 patients who met the inclusion criteria were recruited. 52% of the participants were patients with type 2 DM. The mean duration of DM was 19.6 years. A proportion of 37%, 44%, 27.6% and 25.5% had good control of their blood pressure (BP), low density cholesterol (LDLc), lipids and glucose, respectively, and only 4.3% did well in all factors evaluated. The percentage of poorly controlled BP was four times higher in type 2 than in type 1 DM. Obesity, low cultural level and aggregation of cardiovascular risk factors were associated with poorer control. The degree of control of CVRF in diabetic patients with long disease duration is insufficient. Copyright © 2010 SEEN. Published by Elsevier Espana. All rights reserved.

76 FR 303 - Pipeline Safety: Safety of On-Shore Hazardous Liquid Pipelines

Science.gov (United States)

2011-01-04

... leak detection requirements for all pipelines; whether to require the installation of emergency flow... DEPARTMENT OF TRANSPORTATION Pipeline and Hazardous Materials Safety Administration 49 CFR Part 195 [Docket ID PHMSA-2010-0229] RIN 2137-AE66 Pipeline Safety: Safety of On-Shore Hazardous Liquid...

Advanced Materials Laboratory hazards assessment document

Energy Technology Data Exchange (ETDEWEB)

Barnett, B.; Banda, Z.

1995-10-01

The Department of Energy Order 55OO.3A requires facility-specific hazards assessments be prepared, maintained, and used for emergency planning purposes. This hazards assessment document describes the chemical and radiological hazards associated with the AML. The entire inventory was screened according to the potential airborne impact to onsite and offsite individuals. The air dispersion model, ALOHA, estimated pollutant concentrations downwind from the source of a release, taking into consideration the toxicological and physical characteristics of the release site, the atmospheric conditions, and the circumstances of the release. The greatest distance at which a postulated facility event will produce consequences exceeding the Early Severe Health Effects threshold is 23 meters. The highest emergency classification is a General Emergency. The Emergency Planning Zone is a nominal area that conforms to DOE boundaries and physical/jurisdictional boundaries such as fence lines and streets.

Hazardous constituent source term. Revision 2

International Nuclear Information System (INIS)

1994-01-01

The Department of Energy (DOE) has several facilities that either generate and/or store transuranic (TRU)-waste from weapons program research and production. Much of this waste also contains hazardous waste constituents as regulated under Subtitle C of the Resource Conservation and Recovery Act (RCRA). Toxicity characteristic metals in the waste principally include lead, occurring in leaded rubber gloves and shielding. Other RCRA metals may occur as contaminants in pyrochemical salt, soil, debris, and sludge and solidified liquids, as well as in equipment resulting from decontamination and decommissioning activities. Volatile organic compounds (VOCS) contaminate many waste forms as a residue adsorbed on surfaces or occur in sludge and solidified liquids. Due to the presence of these hazardous constituents, applicable disposal regulations include land disposal restrictions established by Hazardous and Solid Waste Amendments (HSWA). The DOE plans to dispose of TRU-mixed waste from the weapons program in the Waste Isolation Pilot Plant (WIPP) by demonstrating no-migration of hazardous constituents. This paper documents the current technical basis for methodologies proposed to develop a post-closure RCRA hazardous constituent source term. For the purposes of demonstrating no-migration, the hazardous constituent source term is defined as the quantities of hazardous constituents that are available for transport after repository closure. Development of the source term is only one of several activities that will be involved in the no-migration demonstration. The demonstration will also include uncertainty and sensitivity analyses of contaminant transport

Department of Energy: monitoring and control of British Nuclear Fuels plc

International Nuclear Information System (INIS)

1989-01-01

British Nuclear Fuels plc (BNFL) was set up in 1971 to take over the nuclear fuel production and reprocessing activities of the United Kingdom Atomic Energy Authority with the Department of Energy (as majority shareholder) being responsible for the monitoring and control of BNFL's activities. BNFL's activities include the production of nuclear fuel, uranium enrichment, and the transportation and reprocessing of spent fuel. Its major capital investment includes the construction of the Thermal Oxide Reprocessing Plant (THORP) due for completion in 1992. This study examined the effectiveness of the Department's arrangements for monitoring and control and for safeguarding the Government's investment in the company, the arrangements for examining BNFL's capital investment programme and the extent to which the Department's main aims have been achieved. The examination was restricted to the financial performance. The National Audit Office found evidence to suggest that BNFL's financial performance has not kept pace with the general performance level of British Industry. Future success and performance will depend on the success of the THORP plant. (U.K.)

A simplified hazard audit procedures guide

International Nuclear Information System (INIS)

Harrison, D.G.; Tabatabai, A.S.; Scott, W.B.; Murphy, K.J.

1991-02-01

As part of on-going technical support services to the US Department of Energy (DOE), Battelle Pacific Northwest Laboratory (PNL) has developed a simplified hazard audit procedures guide which enables cost-effective and timely assessment and characterization of the DOE nuclear (reactor and nonreactor) and non-nuclear facilities safety profile

SRL process hazards review manual

International Nuclear Information System (INIS)

1980-08-01

The principal objective of the Process Hazards Management Program is to provide a regular, systematic review of each process at the Savannah River Laboratory (SRL) to eliminate injuries and to minimize property damage resulting from process hazards of catastrophic potential. Management effort is directed, through the Du Pont Safety Program, toward those controls and practices that ensure this objective. The Process Hazards Management Program provides an additional dimension to further ensure the health and safety of employees and the public. Du Pont has concluded that an organized approach is essential to obtain an effective and efficient process hazards review. The intent of this manual is to provide guidance in creating such an organized approach to performing process hazards reviews on a continuing basis

Control de configuraciones peligrosas en instalaciones con riesgo asociado // Hazardous configurations control in risk related facilities

Directory of Open Access Journals (Sweden)

Antonio Torres - Valle

2010-05-01

Full Text Available ResumenEl control de configuraciones peligrosas en instalaciones con riesgo asociado es una aplicación delos Análisis Probabilistas de Seguridad (APS previos de las mismas. Una opción de mayor alcancees el uso de monitores de riesgo los que permiten la detección en tiempo real de talesconfiguraciones. Dada la complejidad de los APS y de los monitores de riesgo, esta tarea requiere depersonal experto. El documento presenta un método cualitativo de control de configuracionespeligrosas basado en matrices de dependencias. El algoritmo, informatizado en el códigoCONFIGURACION, puede ser aplicado sin necesidad de APS previos ni uso de monitores de riesgo.La sencillez del método justifica su extensión a instalaciones donde tales herramientas no se handesarrollado, permitiendo así la detección de las configuraciones peligrosas durante su explotación yelevando la seguridad de las plantas. Un sistema similar al descrito se utiliza como ayuda en laoperación de la central nuclear de Embalse. El artículo muestra el uso del método utilizando comobase un sistema de seguridad simplificado.Palabras claves: control de configuración, Análisis Probabilista de Seguridad (APS, matriz de___________________________________________________________________________AbstractThe hazardous configurations control in risk related facilities is an application of the previousProbabilistic Safety Analysis (PSA. A more complete option is the risk monitoring for the on-linedetection of these configurations. The expert personnel are required for this task take into account thecomplexity of the PSA and risk monitor. The paper presents a method of configuration control, basedon dependence matrixes. The algorithm is included in a computer code called CONFIGURACION, todetermine these situations in a qualitative way, without previous PSA results or using a Risk Monitor.The simplicity of the method warrants its application to facilities where these tools have not

Waste Transfer Leaks Control Decision Record

International Nuclear Information System (INIS)

RYAN, G.W.

2000-01-01

Control decision meetings for Waste Transfer Leaks were held on April 24,25,26, and 27, 2000. The agenda for the control decision meetings is included in Appendix A, and attendee lists are included in Appendix B. The purpose of the control decision meetings was to review and revise previously selected controls for the prevention or mitigation of waste transfer leak accidents. Re-evaluation of the controls is warranted due to revisions in the hazard and accident analysis for these Tank Farm events. In particular, calculated radiological consequences are significantly reduced from those currently reported in the Final Safety Analysis Report (FSAR). Revised hazard and accident analysis and a revised control recommendation will be reflected in an Authorization Basis Amendment to be submitted at the Department of Energy, Office of River Protection's (ORP's) request by June 30, 2000 to satisfy ORP Performance Incentive (PI) 2.1.1, Revision 1, ''Authorization Basis Management Process Efficiency Improvement''. The scope of the control decision meetings was to address all waste transfer leak-related hazardous conditions identified in the Tank Farm hazard analysis database, excluding those associated with the use of the Replacement Cross-Site Transfer System (RCSTS) slurry line and sluicing of Tank 241-C-106, which is addressed in FSAR Addendum 1. The scope of this control decision process does include future waste feed delivery waste transfer operations

Advanced Manufacturing Processes Laboratory Building 878 hazards assessment document

Energy Technology Data Exchange (ETDEWEB)

Wood, C.; Thornton, W.; Swihart, A.; Gilman, T.

1994-07-01

The introduction of the hazards assessment process is to document the impact of the release of hazards at the Advanced Manufacturing Processes Laboratory (AMPL) that are significant enough to warrant consideration in Sandia National Laboratories` operational emergency management program. This hazards assessment is prepared in accordance with the Department of Energy Order 5500.3A requirement that facility-specific hazards assessments be prepared, maintained, and used for emergency planning purposes. This hazards assessment provides an analysis of the potential airborne release of chemicals associated with the operations and processes at the AMPL. This research and development laboratory develops advanced manufacturing technologies, practices, and unique equipment and provides the fabrication of prototype hardware to meet the needs of Sandia National Laboratories, Albuquerque, New Mexico (SNL/NM). The focus of the hazards assessment is the airborne release of materials because this requires the most rapid, coordinated emergency response on the part of the AMPL, SNL/NM, collocated facilities, and surrounding jurisdiction to protect workers, the public, and the environment.

Advanced Manufacturing Processes Laboratory Building 878 hazards assessment document

International Nuclear Information System (INIS)

Wood, C.; Thornton, W.; Swihart, A.; Gilman, T.

1994-07-01

The introduction of the hazards assessment process is to document the impact of the release of hazards at the Advanced Manufacturing Processes Laboratory (AMPL) that are significant enough to warrant consideration in Sandia National Laboratories' operational emergency management program. This hazards assessment is prepared in accordance with the Department of Energy Order 5500.3A requirement that facility-specific hazards assessments be prepared, maintained, and used for emergency planning purposes. This hazards assessment provides an analysis of the potential airborne release of chemicals associated with the operations and processes at the AMPL. This research and development laboratory develops advanced manufacturing technologies, practices, and unique equipment and provides the fabrication of prototype hardware to meet the needs of Sandia National Laboratories, Albuquerque, New Mexico (SNL/NM). The focus of the hazards assessment is the airborne release of materials because this requires the most rapid, coordinated emergency response on the part of the AMPL, SNL/NM, collocated facilities, and surrounding jurisdiction to protect workers, the public, and the environment

Washing and chilling as critical control points in pork slaughter hazard analysis and critical control point (HACCP) systems.

Science.gov (United States)

Bolton, D J; Pearce, R A; Sheridan, J J; Blair, I S; McDowell, D A; Harrington, D

2002-01-01

The aim of this research was to examine the effects of preslaughter washing, pre-evisceration washing, final carcass washing and chilling on final carcass quality and to evaluate these operations as possible critical control points (CCPs) within a pork slaughter hazard analysis and critical control point (HACCP) system. This study estimated bacterial numbers (total viable counts) and the incidence of Salmonella at three surface locations (ham, belly and neck) on 60 animals/carcasses processed through a small commercial pork abattoir (80 pigs d(-1)). Significant reductions (P HACCP in pork slaughter plants. This research will provide a sound scientific basis on which to develop and implement effective HACCP in pork abattoirs.

Hazard analysis critical control point (HACCP) in public catering services: a modified method, combined to bacteriologic assay.

Science.gov (United States)

Ferrari, P

1992-01-01

During 1990 and 1991 the Veterinary and Public Health Services of USL 35 of Ravenna carried out a research programme aimed at the control of food-borne diseases in the sector of public catering services, in collaboration with the Public Health Laboratory (Presidio Multizonale di Prevenzione). The objectives were: obtaining sure information about health hazards in public catering services; checking structural characteristics and equipment of workrooms in restaurants, hotels and refectories; verifying food preparation and preservation methods; promoting health education to increase employees' awareness of hygiene-related problems. The first objective, evaluation of the level of the control of the workrooms exerted on the food contamination hazard by pathogenic or potentially pathogenic organisms, was carried out by allotting specific scores to several characteristics of laboratories or workers' habits, as suggested by the "Hazard Analysis Critical Control Point" (HACCP) method for butcher's shops and fish markets. Five hundred ninety-eight public catering service units have been inspected in restaurants, hotels, school-refectories, factories, hospitals and social houses; 2,097 bacteriological examinations by agar-contact plates and swabs were carried out; 118 preserved-food temperatures were measured, especially in deep-frozen and cooked food; 70 food specimens were tested to search for Salmonella spp. and Staphylococcus aureus and measure Total Aerobic Mesophilic Weight. The presence of Enterobacteriaceae and Escherichia coli was also tested.

Preliminary Hazard Classification for the 105-B Reactor

International Nuclear Information System (INIS)

Kerr, N.R.

1997-08-01

This document summarizes the inventories of radioactive and hazardous materials present within the 105-B Reactor and uses the inventory information to determine the preliminary hazard classification for the surveillance and maintenance activities of the facility. The result of this effort was the preliminary hazard classification for the 105-B Building surveillance and maintenance activities. The preliminary hazard classification was determined to be Nuclear Category 3. Additional hazard and accident analysis will be documented in a separate report to define the hazard controls and final hazard classification

Metal food packaging design based on hazard analysis critical control point (HACCP system in canned food safety

Directory of Open Access Journals (Sweden)

Li Xingyi

2016-06-01

Full Text Available This study aims to design metal food packaging with hazard analysis critical control point (HACCP. First, theory of HACCP was introduced in detail. Taking empty cans provided by Wuxi Huapeng Food Packaging Company as an example, we studied migration of bisphenol compounds in coating of food can to food stimulant. Moreover, packaging design of luncheon meat can was taken as an example to confirm whether HACCP system could effectively control migration of phenolic substance. Results demonstrated that, coating of such empty were more likely to contain multiple bisphenol compounds such as bisphenol A (BPA, and bisphenol A diglycidyl ether (BADGE was considered as the leading bisphenol pollutant; food stimulant of different types, storage temperature and time could all impact migration of bisphenol compounds. HACCP system was proved to be effective in controlling hazards of phenolic substance in luncheon meat can and could reduce various phenolic substance indexes to an acceptable range. Therefore, HACCP can control migration of phenolic substance and recontamination of food and thus ensure food safety.

Chemical process hazards analysis

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-02-01

The Office of Worker Health and Safety (EH-5) under the Assistant Secretary for the Environment, Safety and Health of the US Department (DOE) has published two handbooks for use by DOE contractors managing facilities and processes covered by the Occupational Safety and Health Administration (OSHA) Rule for Process Safety Management of Highly Hazardous Chemicals (29 CFR 1910.119), herein referred to as the PSM Rule. The PSM Rule contains an integrated set of chemical process safety management elements designed to prevent chemical releases that can lead to catastrophic fires, explosions, or toxic exposures. The purpose of the two handbooks, ``Process Safety Management for Highly Hazardous Chemicals`` and ``Chemical Process Hazards Analysis,`` is to facilitate implementation of the provisions of the PSM Rule within the DOE. The purpose of this handbook ``Chemical Process Hazards Analysis,`` is to facilitate, within the DOE, the performance of chemical process hazards analyses (PrHAs) as required under the PSM Rule. It provides basic information for the performance of PrHAs, and should not be considered a complete resource on PrHA methods. Likewise, to determine if a facility is covered by the PSM rule, the reader should refer to the handbook, ``Process Safety Management for Highly Hazardous Chemicals`` (DOE- HDBK-1101-96). Promulgation of the PSM Rule has heightened the awareness of chemical safety management issues within the DOE. This handbook is intended for use by DOE facilities and processes covered by the PSM rule to facilitate contractor implementation of the PrHA element of the PSM Rule. However, contractors whose facilities and processes not covered by the PSM Rule may also use this handbook as a basis for conducting process hazards analyses as part of their good management practices. This handbook explains the minimum requirements for PrHAs outlined in the PSM Rule. Nowhere have requirements been added beyond what is specifically required by the rule.

Hazardous Waste Cerification Plan: Hazardous Waste Handling Facility, Lawrence Berkeley Laboratory

International Nuclear Information System (INIS)

1992-02-01

The purpose of this plan is to describe the organization and methodology for the certification of hazardous waste (HW) handled in the Lawrence Berkeley Laboratory (LBL) Hazardous Waste Handling Facility (HWHF). The plan also incorporates the applicable elements of waste reduction, which include both up-front minimization and end- product treatment to reduce the volume and toxicity of the waste; segregation of the waste as it applies to certification; and executive summary of the Quality Assurance Program Plan (QAPP) for the HWHF and a list of the current and planned implementing procedures used in waste certification. The plan provides guidance from the HWHF to waste generators, waste handlers, and the Systems Group Manager to enable them to conduct their activities and carry out their responsibilities in a manner that complies with several requirements of the Federal Resource Conservation and Resource Recovery Act (RCRA), the Federal Department of Transportation (DOT), and the State of California, Code of Regulations (CCR), Title 22

Prevention and control of hazards in seafood

DEFF Research Database (Denmark)

Huss, Hans Henrik; Reilly, A.; Embarek, Peter Karim Ben

2000-01-01

Seafood is high on the list of foods transmitting disease. However, the food safety issues are highly focussed and more than 80% of all seafood-borne outbreaks are related to biotoxins (ciguatoxin), scombrotoxin or the consumption of raw molluscan shellfish. The safety hazards in seafood production...

A proposal for performing software safety hazard analysis

International Nuclear Information System (INIS)

Lawrence, J.D.; Gallagher, J.M.

1997-01-01

Techniques for analyzing the safety and reliability of analog-based electronic protection systems that serve to mitigate hazards in process control systems have been developed over many years, and are reasonably understood. An example is the protection system in a nuclear power plant. The extension of these techniques to systems which include digital computers is not well developed, and there is little consensus among software engineering experts and safety experts on how to analyze such systems. One possible technique is to extend hazard analysis to include digital computer-based systems. Software is frequently overlooked during system hazard analyses, but this is unacceptable when the software is in control of a potentially hazardous operation. In such cases, hazard analysis should be extended to fully cover the software. A method for performing software hazard analysis is proposed in this paper. The method concentrates on finding hazards during the early stages of the software life cycle, using an extension of HAZOP

Waste receiving and processing (WRAP) module 1 hazards assessment. Revision 1

International Nuclear Information System (INIS)

Sutton, L.N.

1997-01-01

This report documents the hazards assessment for the Waste Receiving and Processing Module I (WRAP 1) located on the U.S. Department of Energy (DOE) Hanford Site. Operation of the WRAP 1 is the responsibility of Rust Federal Services Hanford (RFSH). This hazards assessment was conducted to provide the emergency planning technical basis for the WRAP 1. DOE Orders require an emergency planning hazards assessment for each facility that has the potential to reach or exceed the lowest level emergency classification

PUREX facility hazards assessment

International Nuclear Information System (INIS)

Sutton, L.N.

1994-01-01

This report documents the hazards assessment for the Plutonium Uranium Extraction Plant (PUREX) located on the US Department of Energy (DOE) Hanford Site. Operation of PUREX is the responsibility of Westinghouse Hanford Company (WHC). This hazards assessment was conducted to provide the emergency planning technical basis for PUREX. DOE Order 5500.3A requires an emergency planning hazards assessment for each facility that has the potential to reach or exceed the lowest level emergency classification. In October of 1990, WHC was directed to place PUREX in standby. In December of 1992 the DOE Assistant Secretary for Environmental Restoration and Waste Management authorized the termination of PUREX and directed DOE-RL to proceed with shutdown planning and terminal clean out activities. Prior to this action, its mission was to reprocess irradiated fuels for the recovery of uranium and plutonium. The present mission is to establish a passively safe and environmentally secure configuration at the PUREX facility and to preserve that condition for 10 years. The ten year time frame represents the typical duration expended to define, authorize and initiate follow-on decommissioning and decontamination activities

Radiation hazards control activities in BARC and other DAE units in Bombay and Indore: annual report 1994

International Nuclear Information System (INIS)

Bhagwat, A.M.; Pimputkar, D.P.; Mogal, M.P.; Mehta, S.K.

1995-01-01

The radiation hazards control activities of units of Radiation Safety Systems Division stationed at different plants and facilities of Bhabha Atomic Research Centre and other units of Department of Atomic Energy in Bombay are briefly summarised. The activities are reported plantwise and include the following: (i) nature of radioactive operations, (ii) radiological status of the plant, (iii) personnel exposure data including collective and average exposures, (iv) effluent discharges, (v) waste disposal data, and (vi) safety related unusual occurrences and special problems, if any. Important operations for which extensive radiation safety surveillance was provided during the year 1994 are included. During the year 4319 persons were provided with radiation safety coverage at 25 different facilities. The collective dose and the average individual dose for the year 1994 are 6.08 man-Sv and 1.41 mSv respectively. Trends in personnel radiation exposure for a longer period i.e. from 1981 onwards are shown graphically. The figure also shows a steady trend in collective as well as average doses. The major contribution to dose comes from the following facilities: Plutonium Plant, Thorium Plant, Cirus, Radiological Laboratories and Dhruva in the decreasing order. (author). refs., tabs., 1 fig

Radiation hazards control activities in BARC and other DAE units in Bombay and Indore: annual report 1994

Energy Technology Data Exchange (ETDEWEB)

Bhagwat, A M; Pimputkar, D P; Mogal, M P; Mehta, S K [comps.; Bhabha Atomic Research Centre, Bombay (India). Radiation Safety Systems Division

1996-12-31

The radiation hazards control activities of units of Radiation Safety Systems Division stationed at different plants and facilities of Bhabha Atomic Research Centre and other units of Department of Atomic Energy in Bombay are briefly summarised. The activities are reported plantwise and include the following: (i) nature of radioactive operations, (ii) radiological status of the plant, (iii) personnel exposure data including collective and average exposures, (iv) effluent discharges, (v) waste disposal data, and (vi) safety related unusual occurrences and special problems, if any. Important operations for which extensive radiation safety surveillance was provided during the year 1994 are included. During the year 4319 persons were provided with radiation safety coverage at 25 different facilities. The collective dose and the average individual dose for the year 1994 are 6.08 man-Sv and 1.41 mSv respectively. Trends in personnel radiation exposure for a longer period i.e. from 1981 onwards are shown graphically. The figure also shows a steady trend in collective as well as average doses. The major contribution to dose comes from the following facilities: Plutonium Plant, Thorium Plant, Cirus, Radiological Laboratories and Dhruva in the decreasing order. (author). refs., tabs., 1 fig.

Develop and implement preconditioning techniques to control face ejection rockbursts for safer mining in seismically hazardous areas

CSIR Research Space (South Africa)

Toper, AZ

1998-01-01

Full Text Available This research report discusses the development of preconditioning techniques to control face bursts, for safer mining in seismically hazardous areas. Preconditioning involves regularly setting off carefully tailored blasts in the fractured rock...

Nitrous Oxide Explosive Hazards

Science.gov (United States)

2008-05-01

concentrations of N2O. A test program is suggested that could answer questions about decomposition propagation control in large N2O systems and hazards...accident. OSHA fined Scaled Composites for not training their workers informing them about N2O hazards, instructing them on safe procedures, and...seemed present that could produce temperatures in excess of the autogeneous ignition temperature (AIT) for the polymers? Autogeneous ignition

Training for hazardous waste workers

Energy Technology Data Exchange (ETDEWEB)

Favel, K.

1990-10-26

This implementation plan describes the system and provides the information and schedules that are necessary to comply with the Department of Energy (DOE) Albuquerque Operations Office (AL) Memorandum, Reference EPD dated September 11, 1990, Training for Hazardous Waste Workers. The memo establishes the need for identifying employees requiring environmental training, ensuring that the training is received, and meeting documentation and recordkeeping requirements for the training.

Use of institutional controls by federal organizations in the United States

International Nuclear Information System (INIS)

Dziuban, J.; Kennedy, J.; Roles, G.

1999-01-01

A primary risk management goal for Federal agencies is protection of human health from exposure to hazardous materials in the environment. Although there is generally consensus among US Federal agencies on the methods for evaluating risks associated with exposures to hazardous materials, risk management practices have evolved separately. All US agencies use institutional controls as a long-term risk management tool for the disposal of hazardous materials. Regulatory programs depend in part on institutional controls to ensure the integrity of a disposal site is maintained. Yet the emphasis on institutional controls differs among the regulatory programs, as do the specific institutional control requirements. The poster session discusses and compares the historical evolution and current use of institutional controls developed by the US Environmental Protection Agency (EPA), US Department of Energy (DOE) and US Nuclear Regulatory Commission (NRC) under their various statutory authorities. (author)

Towards a decision support system for control of multiple food safety hazards in raw milk production

NARCIS (Netherlands)

Spiegel, van der M.; Sterrenburg, P.; Haasnoot, W.; Fels-Klerx, van der H.J.

2013-01-01

Decision support systems (DSS) for controlling multiple food safety hazards in raw milk production have not yet been developed, but the underlying components are fragmentarily available. This article presents the state-of-the-art of essential DSS elements for judging food safety compliance of raw

Accident hazard evaluation and control decisions on forested recreation sites

Science.gov (United States)

Lee A. Paine

1971-01-01

Accident hazard associated with trees on recreation sites is inherently concerned with probabilities. The major factors include the probabilities of mechanical failure and of target impact if failure occurs, the damage potential of the failure, and the target value. Hazard may be evaluated as the product of these factors; i.e., expected loss during the current...

The implementation of a Hazard Analysis and Critical Control Point management system in a peanut butter ice cream plant

Directory of Open Access Journals (Sweden)

Yu-Ting Hung

2015-09-01

Full Text Available To ensure the safety of the peanut butter ice cream manufacture, a Hazard Analysis and Critical Control Point (HACCP plan has been designed and applied to the production process. Potential biological, chemical, and physical hazards in each manufacturing procedure were identified. Critical control points for the peanut butter ice cream were then determined as the pasteurization and freezing process. The establishment of a monitoring system, corrective actions, verification procedures, and documentation and record keeping were followed to complete the HACCP program. The results of this study indicate that implementing the HACCP system in food industries can effectively enhance food safety and quality while improving the production management.

The juridic control of transboundary shipments of hazardous waste in the United States

International Nuclear Information System (INIS)

Juergensmeyer, J.C.

1989-01-01

An intergovernmental conflict over location of disposal of hazardous waste is discussed; the several definitions of hazardous waste in the United States are analysed; moreover the American Law Regulating the transport and disposal of hazardous waste as well is put in question; also the restrictions an disposal of waste are examined in light of the Constitution of the United States, finally, transboundary shipments of hazardous waste and international agreements on hazardous waste shipment are considered [pt

Idaho National Engineering Laboratory response to the December 13, 1991, Congressional inquiry on offsite release of hazardous and solid waste containing radioactive materials from Department of Energy facilities

International Nuclear Information System (INIS)

Shapiro, C.; Garcia, K.M.; McMurtrey, C.D.; Williams, K.L.; Jordan, P.J.

1992-05-01

This report is a response to the December 13, 1991, Congressional inquiry that requested information on all hazardous and solid waste containing radioactive materials sent from Department of Energy facilities to offsite facilities for treatment or disposal since January 1, 1981. This response is for the Idaho National Engineering Laboratory. Other Department of Energy laboratories are preparing responses for their respective operations. The request includes ten questions, which the report divides into three parts, each responding to a related group of questions. Part 1 answers Questions 5, 6, and 7, which call for a description of Department of Energy and contractor documentation governing the release of waste containing radioactive materials to offsite facilities. ''Offsite'' is defined as non-Department of Energy and non-Department of Defense facilities, such as commercial facilities. Also requested is a description of the review process for relevant release criteria and a list of afl Department of Energy and contractor documents concerning release criteria as of January 1, 1981. Part 2 answers Questions 4, 8, and 9, which call for information about actual releases of waste containing radioactive materials to offsite facilities from 1981 to the present, including radiation levels and pertinent documentation. Part 3 answers Question 10, which requests a description of the process for selecting offsite facilities for treatment or disposal of waste from Department of Energy facilities. In accordance with instructions from the Department of Energy, the report does not address Questions 1, 2, and 3

Innovative assesment of the seismic hazard from Vrancea sources

International Nuclear Information System (INIS)

Panza, Giuliano Francesco

2002-01-01

In the framework of a very fruitful, stimulating and still ongoing collaboration between the National Institute for Earth Physics - Bucharest, the Department of Earth Sciences - University of Trieste and The Abdus Salam International Center for Theoretical Physics - SAND Group, several innovative steps forwards have been made in the assessment of the seismic hazard generated by Vrancea seismicity. The limits of currently applied probabilistic approaches are partly overcome by the introduction of hazard scenarios based on the deterministic, realistic modeling of ground motion. The ongoing co-operation represents a fundamental contribution to the reliable assessment of seismic hazard, and has been recently enriched by the participation of Bulgarian scientists, who are facing, in the urban settlements close to the Romanian border, a seismic hazard similar to the one in Bucharest. (author)

Tank farms hazards assessment

International Nuclear Information System (INIS)

Broz, R.E.

1994-01-01

Hanford contractors are writing new facility specific emergency procedures in response to new and revised US Department of Energy (DOE) Orders on emergency preparedness. Emergency procedures are required for each Hanford facility that has the potential to exceed the criteria for the lowest level emergency, an Alert. The set includes: (1) a facility specific procedure on Recognition and Classification of Emergencies, (2) area procedures on Initial Emergency Response and, (3) an area procedure on Protective Action Guidance. The first steps in developing these procedures are to identify the hazards at each facility, identify the conditions that could release the hazardous material, and calculate the consequences of the releases. These steps are called a Hazards Assessment. The final product is a document that is similar in some respects to a Safety Analysis Report (SAR). The document could br produced in a month for a simple facility but could take much longer for a complex facility. Hanford has both types of facilities. A strategy has been adopted to permit completion of the first version of the new emergency procedures before all the facility hazards Assessments are complete. The procedures will initially be based on input from a task group for each facility. This strategy will but improved emergency procedures in place sooner and therefore enhance Hanford emergency preparedness. The purpose of this document is to summarize the applicable information contained within the Waste Tank Facility ''Interim Safety Basis Document, WHC-SD-WM-ISB-001'' as a resource, since the SARs covering Waste Tank Operations are not current in all cases. This hazards assessment serves to collect, organize, document and present the information utilized during the determination process

Engineered and Administrative Safety Systems for the Control of Prompt Radiation Hazards at Accelerator Facilities

International Nuclear Information System (INIS)

Liu, James C.; SLAC; Vylet, Vashek; Walker, Lawrence S.

2007-01-01

The ANSI N43.1 Standard, currently in revision (ANSI 2007), sets forth the requirements for accelerator facilities to provide adequate protection for the workers, the public and the environment from the hazards of ionizing radiation produced during and from accelerator operations. The Standard also recommends good practices that, when followed, provide a level of radiation protection consistent with those established for the accelerator communities. The N43.1 Standard is suitable for all accelerator facilities (using electron, positron, proton, or ion particle beams) capable of producing radiation, subject to federal or state regulations. The requirements (see word 'shall') and recommended practices (see word 'should') are prescribed in a graded approach that are commensurate with the complexity and hazard levels of the accelerator facility. Chapters 4, 5 and 6 of the N43.1 Standard address specially the Radiation Safety System (RSS), both engineered and administrative systems, to mitigate and control the prompt radiation hazards from accelerator operations. The RSS includes the Access Control System (ACS) and Radiation Control System (RCS). The main requirements and recommendations of the N43.1 Standard regarding the management, technical and operational aspects of the RSS are described and condensed in this report. Clearly some aspects of the RSS policies and practices at different facilities may differ in order to meet the practical needs for field implementation. A previous report (Liu et al. 2001a), which reviews and summarizes the RSS at five North American high-energy accelerator facilities, as well as the RSS references for the 5 labs (Drozdoff 2001; Gallegos 1996; Ipe and Liu 1992; Liu 1999; Liu 2001b; Rokni 1996; TJNAF 1994; Yotam et al. 1991), can be consulted for the actual RSS implementation at various laboratories. A comprehensive report describing the RSS at the Stanford Linear Accelerator Center (SLAC 2006) can also serve as a reference

Flood Hazard Assessment for the Savannah River Site

International Nuclear Information System (INIS)

Chen, K.F.

2000-01-01

A method was developed to determine the probabilistic flood elevation curves for certain Savannah River Site (SRS) facilities. This paper presents the method used to determine the probabilistic flood elevation curve for F-Area due to runoff from the Upper Three Runs basin. Department of Energy (DOE) Order 420.1, Facility Safety, outlines the requirements for Natural Phenomena Hazard (NPH) mitigation for new and existing DOE facilities. The NPH considered in this paper is flooding. The facility-specific probabilistic flood hazard curve defines as a function of water elevation the annual probability of occurrence or the return period in years. Based on facility-specific probabilistic flood hazard curves and the nature of facility operations (e.g., involving hazardous or radioactive materials), facility managers can design permanent or temporary devices to prevent the propagation of flood on site, and develop emergency preparedness plans to mitigate the consequences of floods. A method was developed to determine the probabilistic flood hazard curves for SRS facilities. The flood hazard curves for the SRS F-Area due to flooding in the Upper Three Runs basin are presented in this paper

Flood Hazard Assessment for the Savannah River Site

International Nuclear Information System (INIS)

Chen, K.F.

1999-01-01

'A method was developed to determine the probabilistic flood elevation curves for certain Savannah River Site (SRS) facilities. This paper presents the method used to determine the probabilistic flood elevation curve for F-Area due to runoff from the Upper Three Runs basin. Department of Energy (DOE) Order 420.1, Facility Safety, outlines the requirements for Natural Phenomena Hazard (NPH) mitigation for new and existing DOE facilities. The NPH considered in this paper is flooding. The facility-specific probabilistic flood hazard curve defines as a function of water elevation the annual probability of occurrence or the return period in years. Based on facility-specific probabilistic flood hazard curves and the nature of facility operations (e.g., involving hazardous or radioactive materials), facility managers can design permanent or temporary devices to prevent the propagation of flood on site, and develop emergency preparedness plans to mitigate the consequences of floods.'

12 CFR 22.6 - Required use of standard flood hazard determination form.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 1 2010-01-01 2010-01-01 false Required use of standard flood hazard determination form. 22.6 Section 22.6 Banks and Banking COMPTROLLER OF THE CURRENCY, DEPARTMENT OF THE TREASURY... the Act. The standard flood hazard determination form may be used in a printed, computerized, or...

Can the Hazard Assessment and Critical Control Points (HACCP) system be used to design process-based hygiene concepts?

Science.gov (United States)

Hübner, N-O; Fleßa, S; Haak, J; Wilke, F; Hübner, C; Dahms, C; Hoffmann, W; Kramer, A

2011-01-01

Recently, the HACCP (Hazard Analysis and Critical Control Points) concept was proposed as possible way to implement process-based hygiene concepts in clinical practice, but the extent to which this food safety concept can be transferred into the health care setting is unclear. We therefore discuss possible ways for a translation of the principles of the HACCP for health care settings. While a direct implementation of food processing concepts into health care is not very likely to be feasible and will probably not readily yield the intended results, the underlying principles of process-orientation, in-process safety control and hazard analysis based counter measures are transferable to clinical settings. In model projects the proposed concepts should be implemented, monitored, and evaluated under real world conditions.

Ionizing radiation hazards and its protection in a radiodiagnostic department

International Nuclear Information System (INIS)

Sinha, R.P.; Rai, S.D.

1977-01-01

After mentioning the contribution to gonadal dose from natural background and man-made radiation sources including those used in medical radiology, methods for minimising the radiation dose to the patients and staff in x-ray diagnostic department are discussed in brief. (M.G.B.)

Risk Assessment of Physical Health Hazards in Al-Azhar University Hospital in New Damietta, Egypt

OpenAIRE

Mohammed El-Hady Imam*, Raed Mohammed Alazab**,

2013-01-01

Introduction: Personnel working in hospitals are exposed to many occupational hazards that may threaten their health and safety. Physical hazards that are encountered in hospital working environment include temperature, illumination, noise, electrical injuries, and radiation. Objectives: The objectives of this study were to identify physical health hazards in all departments of Al-Azhar University Hospital in new Damietta, to measure risk level of these hazards, and to recognize safety me...

Flood hazard assessment for the Savannah River Site

International Nuclear Information System (INIS)

Chen, K.F.

2000-01-01

A method was developed to determine the probabilistic flood elevation curves for certain Savannah River Site (SRS) facilities. This paper presents the method used to determine the probabilistic flood elevation curve for F-Area due to runoff from the Upper Three Runs basin. Department of Energy (DOE) Order 420.1, Facility Safety, outlines the requirements for Natural Phenomena Hazard (NPH) mitigation for new and existing DOE facilities. The NPH considered in this paper is flooding. The facility-specific probabilistic flood hazard curve defines as a function of water elevation the annual probability of occurrence or the return period in years. Based on facility-specific probabilistic flood hazard curves and the nature of facility operations (e.g., involving hazardous or radioactive materials), facility managers can design permanent or temporary devices to prevent the propagation of flood on site, and develop emergency preparedness plans to mitigate the consequences of floods. The flood hazard curves for the SRS F-Area due to flooding in the Upper Three Runs basin are presented in this paper

76 FR 25576 - Pipeline Safety: Applying Safety Regulations to All Rural Onshore Hazardous Liquid Low-Stress Lines

Science.gov (United States)

2011-05-05

... DEPARTMENT OF TRANSPORTATION Pipeline and Hazardous Materials Safety Administration 49 CFR Part... to All Rural Onshore Hazardous Liquid Low-Stress Lines AGENCY: Pipeline and Hazardous Materials..., suggested that the scope should include low-stress gas pipelines such as those associated with coal bed...

HAZARD ANALYSIS SOFTWARE

International Nuclear Information System (INIS)

Sommer, S; Tinh Tran, T.

2008-01-01

Washington Safety Management Solutions, LLC developed web-based software to improve the efficiency and consistency of hazard identification and analysis, control selection and classification, and to standardize analysis reporting at Savannah River Site. In the new nuclear age, information technology provides methods to improve the efficiency of the documented safety analysis development process which includes hazard analysis activities. This software provides a web interface that interacts with a relational database to support analysis, record data, and to ensure reporting consistency. A team of subject matter experts participated in a series of meetings to review the associated processes and procedures for requirements and standard practices. Through these meetings, a set of software requirements were developed and compiled into a requirements traceability matrix from which software could be developed. The software was tested to ensure compliance with the requirements. Training was provided to the hazard analysis leads. Hazard analysis teams using the software have verified its operability. The software has been classified as NQA-1, Level D, as it supports the analysis team but does not perform the analysis. The software can be transported to other sites with alternate risk schemes. The software is being used to support the development of 14 hazard analyses. User responses have been positive with a number of suggestions for improvement which are being incorporated as time permits. The software has enforced a uniform implementation of the site procedures. The software has significantly improved the efficiency and standardization of the hazard analysis process

Environmental and occupational hazards associated with decontamination solutions (a)

International Nuclear Information System (INIS)

Levanthal, L.

1985-01-01

Some of the reagents employed in the decontamination of reactor coolant systems are potentially hazardous. Potential exposure to decontamination agents by operating personnel, or members of the general population, could occur during use, processing, transportation to, or disposal at a low-level waste site. Federal and state agencies have promulgated regulations relevant to the disposal of decontamination solution waste to prevent acute or chronic exposures. In particular, the Nuclear Regulatory Commission (NRC), U.S. Environmental Protection Agency (EPA), Department of Transportation (DOT), Department of Labor - Occupational Safety and Health Administration (OSHA), State of South Carolina, State of Nevada, and the State of Washington have such regulations. These regulations may impact on the choice of decontamination solutions, operations procedures, processing methods, or disposal methods. Laws and regulations relate to both chemically hazardous, or toxic materials and to radioactive hazards. Laws which regulate the exposure of workers and the general public to effluents and emissions during processing, disposal and transport have been abstracted. As a result of these regulations, utilities are required to obtain permits to perform monitoring and sampling of personnel and the on-site and off-site environment, provide proper protective clothing and ventilation, make certain the solutions are properly contained during use, storage and processing, and destroy and/or properly immobilize the residues for disposal. Waste treatment processes such as neutralization, ion exchange, evaporation, incineration, etc., must not produce, nor result in hazardous emissions, effluents, residues, or hazards to workers. The laws also stipulate record keeping and documentation

Hazardous metals in yellow items used in RCAs

International Nuclear Information System (INIS)

Brown, K.F.; Rankin, W.N.

1992-01-01

Yellow items used in Radiologically Controlled Areas (RCAs) that could contain hazardous metals were identified. X-ray fluorescence analyses indicated that thirty of the fifty-two items do contain hazardous metals. It is important to minimize the hazardous metals put into the wastes. The authors recommend that the specifications for all yellow items stocked in Stores be changed to specify that they contain no hazardous metals

The role of the health physicist in the control of airborne radioactive hazards

International Nuclear Information System (INIS)

Basson, J.K.

1978-01-01

Health physics is based on the ease and sensitivity with which ionising radiations can be measured, as well as on the extensive medical knowledge of its long-term effects. Such studies have led to fundamental contributions to scientific health protection as well as practical occupational hygiene. The first aspect is illustrated with aerosol biophysics as example, while the practical control of airborne radioactive hazards in South Africa is described inside uranium plants as well as in the environment of nuclear installations [af

The implementation of a Hazard Analysis and Critical Control Point management system in a peanut butter ice cream plant.

Science.gov (United States)

Hung, Yu-Ting; Liu, Chi-Te; Peng, I-Chen; Hsu, Chin; Yu, Roch-Chui; Cheng, Kuan-Chen

2015-09-01

To ensure the safety of the peanut butter ice cream manufacture, a Hazard Analysis and Critical Control Point (HACCP) plan has been designed and applied to the production process. Potential biological, chemical, and physical hazards in each manufacturing procedure were identified. Critical control points for the peanut butter ice cream were then determined as the pasteurization and freezing process. The establishment of a monitoring system, corrective actions, verification procedures, and documentation and record keeping were followed to complete the HACCP program. The results of this study indicate that implementing the HACCP system in food industries can effectively enhance food safety and quality while improving the production management. Copyright © 2015. Published by Elsevier B.V.

United States Department of Energy Automated Transportation Management System

International Nuclear Information System (INIS)

Portsmouth, J.H.

1992-01-01

At the US Department of Energy (DOE) 80 transportation facilities, each contractor's transportation management operation has different internal and site specific procedures, and reports to a DOE regional Field Office Traffic Manager (FOTM). The DOE Transportation Management Program (TMP) has the responsibility to manage a transportation program for safe, efficient, and economical transportation of DOE-owned materials. The TMP develops and administers transportation/traffic operations management policies and programs for materials; including radioactive materials, other hazardous materials, hazardous substances, and hazardous wastes, pursuant to applicable federal regulations, such as the Code of Federal Register, Sections 40 and 49. Transportation management has become an increasingly critical primarily because of transportation issues regarding the shipment of radioactive materials and hazardous wastes that are frequently the focus of public concerns. A large shipments and requiring millions of business transactions necessitates the establishment of automated systems, programs, procedures, and controls to ensure that the transportation management process in being handled in a safe, efficient, and economical manner. As the mission of many DOE facilities changes from production of special nuclear materials for defense purposes to environmental restoration and waste management, the role of transportation management will become even more important to the safe and efficient movement of waste materials to prescribed locations. In support of this role, the Automated Transportation Management System (ATMS) was conceived to assist the DOE and its contractors in the performance of their day-to-day transportation management activities. The ATMS utilizes the latest in technology and will supply state-of-the-art automated transportation management for current and future DOE transportation requirements

Performance-oriented packagings for hazardous materials: Resource guide

Energy Technology Data Exchange (ETDEWEB)

1993-09-01

This document provides recommendations to US Department of Energy (DOE) shippers regarding packaging that meet performance-oriented packaging requirements implemented by US Department of Transportation (DOT) in rulemaking HM-181 (December 21, 1990) and subsequent actions. The packaging described in this document are certified by their vendor to comply with requirements for Packing Group I, II, or III hazardous materials packaging. The intent of this document is to share information between DOE and contractors and at all DOE facilities.

Performance-oriented packagings for hazardous materials: Resource guide

International Nuclear Information System (INIS)

1993-09-01

This document provides recommendations to US Department of Energy (DOE) shippers regarding packaging that meet performance-oriented packaging requirements implemented by US Department of Transportation (DOT) in rulemaking HM-181 (December 21, 1990) and subsequent actions. The packaging described in this document are certified by their vendor to comply with requirements for Packing Group I, II, or III hazardous materials packaging. The intent of this document is to share information between DOE and contractors and at all DOE facilities

Comparability between NQA-1 and the QA programs for analytical laboratories within the nuclear industry and EPA hazardous waste laboratories

International Nuclear Information System (INIS)

English, S.L.; Dahl, D.R.

1989-01-01

There is increasing cooperation between the Department of Energy (DOE), Department of Defense (DOD), and the Environmental Protection Agency (EPA) in the activities associated with monitoring and clean-up of hazardous wastes. Pacific Northwest Laboratory (PNL) examined the quality assurance/quality control programs that the EPA requires of the private sector when performing routine analyses of hazardous wastes to confirm how or if the requirements correspond with PNL's QA program based upon NQA-1. This paper presents the similarities and differences between NQA-1 and the QA program identified in ASTM-C1009-83, Establishing a QA Program for Analytical Chemistry Laboratories within the Nuclear Industry; EPA QAMS-005/80, Interim Guidelines and Specifications for Preparing Quality Assurance Project Plans, which is referenced in Statements of Work for CERCLA analytical activities; and Chapter 1 of SW-846, which is used in analyses of RCRA samples. The EPA QA programs for hazardous waste analyses are easily encompassed within an already established NQA-1 QA program. A few new terms are introduced and there is an increased emphasis upon the QC/verification, but there are many of the same basic concepts in all the programs

41 CFR 101-26.606 - Supply support available from the inventory control points of the military departments.

Science.gov (United States)

2010-07-01

... from the inventory control points of the military departments. 101-26.606 Section 101-26.606 Public... § 101-26.606 Supply support available from the inventory control points of the military departments. Federal civil agencies may obtain items of supply which are procured and managed by the inventory control...

HACCP (Hazard Analysis and Critical Control Points) to guarantee safe water reuse and drinking water production--a case study.

Science.gov (United States)

Dewettinck, T; Van Houtte, E; Geenens, D; Van Hege, K; Verstraete, W

2001-01-01

To obtain a sustainable water catchment in the dune area of the Flemish west coast, the integration of treated domestic wastewater in the existing potable water production process is planned. The hygienic hazards associated with the introduction of treated domestic wastewater into the water cycle are well recognised. Therefore, the concept of HACCP (Hazard Analysis and Critical Control Points) was used to guarantee hygienically safe drinking water production. Taking into account the literature data on the removal efficiencies of the proposed advanced treatment steps with regard to enteric viruses and protozoa and after setting high quality limits based on the recent progress in quantitative risk assessment, the critical control points (CCPs) and points of attention (POAs) were identified. Based on the HACCP analysis a specific monitoring strategy was developed which focused on the control of these CCPs and POAs.

Hydrothermal Liquefaction Treatment Hazard Analysis Report

Energy Technology Data Exchange (ETDEWEB)

Lowry, Peter P. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wagner, Katie A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2016-09-12

Hazard analyses were performed to evaluate the modular hydrothermal liquefaction treatment system. The hazard assessment process was performed in 2 stages. An initial assessment utilizing Hazard Identification and Preliminary Hazards Analysis (PHA) techniques identified areas with significant or unique hazards (process safety-related hazards) that fall outside of the normal operating envelope of PNNL and warranted additional analysis. The subsequent assessment was based on a qualitative What-If analysis. The analysis was augmented, as necessary, by additional quantitative analysis for scenarios involving a release of hazardous material or energy with the potential for affecting the public. The following selected hazardous scenarios received increased attention: •Scenarios involving a release of hazardous material or energy, controls were identified in the What-If analysis table that prevent the occurrence or mitigate the effects of the release. •Scenarios with significant consequences that could impact personnel outside the immediate operations area, quantitative analyses were performed to determine the potential magnitude of the scenario. The set of “critical controls” were identified for these scenarios (see Section 4) which prevent the occurrence or mitigate the effects of the release of events with significant consequences.

Financial Management: Poor Internal Controls Expose Department of Education to Improper Payments

National Research Council Canada - National Science Library

2001-01-01

On July 24, 2001, we testified before your subcommittee on our ongoing review of the Department of Education's payment processes and how the existing internal control weaknesses we have noted thus far...

TECHNICAL BASIS DOCUMENT FOR NATURAL EVENT HAZARDS

International Nuclear Information System (INIS)

KRIPPS, L.J.

2006-01-01

This technical basis document was developed to support the documented safety analysis (DSA) and describes the risk binning process and the technical basis for assigning risk bins for natural event hazard (NEH)-initiated accidents. The purpose of the risk binning process is to determine the need for safety-significant structures, systems, and components (SSC) and technical safety requirement (TSR)-level controls for a given representative accident or represented hazardous conditions based on an evaluation of the frequency and consequence. Note that the risk binning process is not applied to facility workers, because all facility worker hazardous conditions are considered for safety-significant SSCs and/or TSR-level controls

Criteria and Processes for the Certification of Non-Radioactive Hazardous and Non-Hazardous Wastes

International Nuclear Information System (INIS)

Dominick, J.

2008-01-01

This document details Lawrence Livermore National Laboratory's (LLNL) criteria and processes for determining if potentially volumetrically contaminated or potentially surface contaminated wastes are to be managed as material containing residual radioactivity or as non-radioactive. This document updates and replaces UCRL-AR-109662, Criteria and Procedures for the Certification of Nonradioactive Hazardous Waste (Reference 1), also known as 'The Moratorium', and follows the guidance found in the U.S. Department of Energy (DOE) document, Performance Objective for Certification of Non-Radioactive Hazardous Waste (Reference 2). The 1992 Moratorium document (UCRL-AR-109662) is three volumes and 703 pages. The first volume provides an overview of the certification process and lists the key radioanalytical methods and their associated Limits of Sensitivities. Volumes Two and Three contain supporting documents and include over 30 operating procedures, QA plans, training documents and organizational charts that describe the hazardous and radioactive waste management system in place in 1992. This current document is intended to update the previous Moratorium documents and to serve as the top-tier LLNL institutional Moratorium document. The 1992 Moratorium document was restricted to certification of Resource Conservation and Recovery Act (RCRA), State and Toxic Substances Control Act (TSCA) hazardous waste from Radioactive Material Management Areas (RMMA). This still remains the primary focus of the Moratorium; however, this document increases the scope to allow use of this methodology to certify other LLNL wastes and materials destined for off-site disposal, transfer, and re-use including non-hazardous wastes and wastes generated outside of RMMAs with the potential for DOE added radioactivity. The LLNL organization that authorizes off-site transfer/disposal of a material or waste stream is responsible for implementing the requirements of this document. The LLNL Radioactive and

SCI Hazard Report Methodology

Science.gov (United States)

Mitchell, Michael S.

2010-01-01

This slide presentation reviews the methodology in creating a Source Control Item (SCI) Hazard Report (HR). The SCI HR provides a system safety risk assessment for the following Ares I Upper Stage Production Contract (USPC) components (1) Pyro Separation Systems (2) Main Propulsion System (3) Reaction and Roll Control Systems (4) Thrust Vector Control System and (5) Ullage Settling Motor System components.

Quality control in Department of Nuclear Medicine, Clinical Center Banja Luka, RS, Bosnia and Herzegovina

International Nuclear Information System (INIS)

Goran Vuleta

2007-01-01

Complete test of publication follows. The aim of this work is to give a review of situations in the Department of Nuclear Medicine in Banja Luka related to quality control. We must perform daily, weekly and monthly control of equipment in the Department of Nuclear Medicine, and we must keep records. In our Department we have equipment from different producers and different year of production: 3 gamma cameras (1973, 1989, 2000); 2 auto gamma counters (2000, 2006); 2 dose calibrators (1973, 2000); 1 thyroid uptake system (2000). Normally procedures for quality control are also different. The situation, according to results of quality control is good. All equipment is working normally and with good performance (except one gamma camera - a problem with hard drive), but we don't have a routine daily control and periodical control for others tests. Keeping a records is another problem. Why? 1. In Bosnia and Herzegovina we don't have Regulatory authority. That means that we don't have legislation, rules, inspection or any other regulatory instruments. 2. There is only school for nurses, we have no special school for medical technician. So, we need an education in that field. 3. Very small number of physicist in hospital, no education for medical and nuclear medicine physicist. Conclusion. Situation in Department of Nuclear Medicine in Banja Luka related to quality control is on the medium level. We are trying to put that on the higher level, but to accomplish that we need additional education for nurses (technicians) and physicist.

New York hazardous substances emergency events surveillance: learning from hazardous substances releases to improve safety

International Nuclear Information System (INIS)

Welles, Wanda Lizak; Wilburn, Rebecca E.; Ehrlich, Jenny K.; Floridia, Christina M.

2004-01-01

Since 1993, the New York State Department of Health, funded by the Agency for Toxic Substances and Disease Registry, has collected data about non-petroleum hazardous substances releases through the Hazardous Substances Emergency Events Surveillance (NYHSEES) project. This study investigates risk factors for hazardous substances releases that may result in public health consequences such as injury or reported health effects. The 6428 qualifying events that occurred during the 10-year-period of 1993-2002 involved 8838 hazardous substances, 842 evacuations, more than 75,419 people evacuated, and more than 3120 people decontaminated. These events occurred both at fixed facilities (79%) and during transport (21%). The causative factors most frequently contributing to reported events were equipment failure (39%) and human error (33%). Five of the 10 chemicals most frequently associated with injuries were also among the 10 chemicals most frequently involved in reported events: sulfuric acid, hydrochloric acid, ammonia, sodium hypochlorite, and carbon monoxide. The chemical categories most frequently associated with events, and with events with adverse health effects were volatile organic compounds (VOCs) and solvents, and acids. Events with releases of hazardous substances were associated with injuries to 3089 people including employees (37%), responders (12%), the general public (29%) and students (22%). The most frequently reported adverse health effects were respiratory irritation, headache, and nausea or vomiting. Most of the injured were transported to the hospital, treated, and released (55%) or treated at the scene (29%). These data have been used for emergency response training, planning, and prevention activities to reduce morbidity and mortality from future events

New methodology to implement quality control programs in medical imaging departments

International Nuclear Information System (INIS)

Furquim, Tania A.C.; Yanikian, Denise; Costa, Paulo R.

1996-01-01

The implementation of quality control programmes is studied in order to assure a better performance in medical imaging departments. The necessity of a continuous training of all technicians involved is highlighted. The contribution of these professionals is emphasized as fundamental to the success of the project

Communication in hazardous environments

International Nuclear Information System (INIS)

Rankin, W.N.; Herold, T.R.

1986-01-01

Radios were investigated for use in hazardous environments where protective breathing equipment such as plastic suits and respirators interfere with communication. A radio system, manufactured by Communications-Applied technology (C-AT), was identified that was designed specifically for hazardous environment communications. This equipment had been used successfully by the US Army and NASA for several years. C-AT equipment was evaluated in plantwide applications at the Savannah River Plant (SRP) using temporary frequencies obtained by the Department of Energy-Savannah River (DOE-SR). Radios performed well in all applications, which included a tritium facility, high-level caves, a nuclear reactor building, tank farm, and a canyon building interior. Permanent frequencies were obtained by DOE-SR for two complete six-man C-AT systems at SRP. Because of the relatively short range of these systems, replicates will cover all applications of this type of equipment plantwide. Twelve radio systems are currently being used successfully in plantwide applications

49 CFR 392.14 - Hazardous conditions; extreme caution.

Science.gov (United States)

2010-10-01

... CARRIER SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION FEDERAL MOTOR CARRIER SAFETY REGULATIONS DRIVING OF COMMERCIAL MOTOR VEHICLES Driving of Commercial Motor Vehicles § 392.14 Hazardous conditions... nearest point at which the safety of passengers is assured. [33 FR 19732, Dec. 25, 1968, as amended at 60...

75 FR 8239 - School Food Safety Program Based on Hazard Analysis and Critical Control Point Principles (HACCP...

Science.gov (United States)

2010-02-24

... (HACCP); Approval of Information Collection Request AGENCY: Food and Nutrition Service, USDA. ACTION... Safety Program Based on Hazard Analysis and Critical Control Point Principles (HACCP) was published on... must be based on the (HACCP) system established by the Secretary of Agriculture. The food safety...

Progress towards developing consistent design and evaluation guidelines for DOE facilities subjected to natural phenomena hazards

International Nuclear Information System (INIS)

Kennedy, R.P.; Short, S.A.; McDonald, J.R.; McCann, M.W. Jr.; Reed, J.W.

1985-01-01

Probabilistic definitions of earthquake, wind and tornado natural phenomena hazards for many Department of Energy (DOE) facilities throughout the United States have been developed. In addition, definitions of the flood hazards which might affect these locations are currently being developed. The Department of Energy Natural Phenomena Hazards Panel is now preparing a document to provide guidance and criteria for DOE facility managers to assure that DOE facilities are adequately constructed to resist the effects of natural phenomena such as earthquake, strong wind and flood. The intent of this document is to provide instruction on how to utilize the hazard definitions to evaluate existing facilities and design new facilities in a manner such that the risk of adverse consequences is consistent with the cost, function, and danger to the public or environment of the facility. Potential effects on facilities of natural phenomena hazards are emphasized in this paper. The philosophy for mitigating these effects to be employed in the design and evaluation guidelines is also presented

76 FR 73011 - Pipeline and Hazardous Materials Safety Administration

Science.gov (United States)

2011-11-28

... DEPARTMENT OF TRANSPORTATION Pipeline and Hazardous Materials Safety Administration Office of... Safety Administration (PHMSA), DOT. ACTION: Notice of actions on Special Permit Applications. SUMMARY: In... reissue the Nuclear 173.56(b)(3)(i special permit Security ). originally issued Administration on an...

Final hazard classification for the 183-C D ampersand D project

International Nuclear Information System (INIS)

Zimmer, J.J.

1995-01-01

The intent of this document is to provide a final Hazard Classification for the Decontamination and Decommissioning (D ampersand D) activities associated with the 183-C Filter Plant/Pump Room facility. The Hazard Classification was determined based upon DOE-EM-STD-5502-94, ''DOE Limited Standard, Hazard Baseline Documentation,'' issued by the US Department of Energy. The 183-C Filter Plant/Pump Room facility was constructed to support operations of the 105-B and 105-C Reactors at the Hanford Site. Since shutdown of the 105-C Reactor in April 1969, the 183-C facility has been kept in a safe storage condition

Environmental control technology activities of the Department of Energy in FY 1977

International Nuclear Information System (INIS)

1977-11-01

The Department of Energy is responsible for the research, development, and demonstration of emerging energy technologies and the promotion of energy conservation. An integral and significant part of that responsibility includes the balancing of energy goals with environmental requirements to protect and enhance the general health, safety, and welfare of the nation. This requires that environmental effects be considered and mitigating measures be taken in all energy processes through incorporation of environmental and safety controls which are developed as an integral part of energy system design. This inventory of environmental control technology activities was initiated by the Administrator, ERDA, prior to the incorporation of that administration within the Department of Energy. This compilation of total Energy Research and Development Administration (ERDA) environmental control technology activities, and associated funding, related to environmental control technology identifies the resources committed by ERDA to demonstrate its objective to protect and enhance the general health, safety, and welfare of the nation in the research, development, and demonstration of energy systems. Only ERDA research, development, and demonstration activities are covered in this report. The compilation for FY 1978 will encompass all of the DOE activities

Impacts on health and safety from transfer/consolidation of nuclear materials and hazardous chemicals

International Nuclear Information System (INIS)

Gallucci, R.H.V.

1994-11-01

Environmental restoration plans at the US Department of Energy (USDOE) Hanford Site calls for transfer/consolidation of ''targets/threats,'' namely nuclear materials and hazardous chemicals. Reductions in the health and safety hazards will depend on the plans implemented. Pacific Northwest Laboratory (PNL) estimated these potential impacts, assuming implementation of the current reference plan and employing ongoing risk and safety analyses. The results indicated the potential for ''significant'' reductions in health and safety hazards in the long term (> 25 years) and a potentially ''noteworthy'' reduction in health hazard in the short term (≤ 25 years)

Environmental resources of selected areas of Hawaii: Geological hazards

Energy Technology Data Exchange (ETDEWEB)

Staub, W.P.; Reed, R.M.

1995-03-01

This report has been prepared to make available and archive the background scientific data and related information collected on geologic hazards during the preparation of the environmental impact statement (EIS) for Phases 3 and 4 of the Hawaii Geothermal Project (HGP) as defined by the state of Hawaii in its April 1989 proposal to Congress. The US Department of Energy (DOE) published a notice withdrawing its Notice of Intent to prepare the HGP-EIS. Since the state of Hawaii is no longer pursuing or planning to pursue the HGP, DOE considers the project to be terminated. This report presents a review of current information on geologic hazards in the Hawaiian Islands. Interrelationships among these hazards are discussed. Probabilities of occurrence of given geologic hazards are provided in various regions where sufficient geologic or historical data are available. Most of the information contained herein is compiled from recent US Geological Survey (USGS) publications and USGS open-file reports related to this project. This report describes the natural geologic hazards present in the area and does not represent an assessment of environmental impacts. Geologic hazards originate both onshore and offshore. Onshore geologic hazards such as volcanic eruptions, earthquakes, surface rupture, landslides, uplift and subsidence occur mainly on the southern third of the island of Hawaii (hereinafter referred to as Hawaii). Offshore geologic hazards are more widely distributed throughout the Hawaiian Islands. Examples of offshore geologic hazards are submarine landslides, turbidity currents, and seismic sea waves (tsunamis).

H-Area Hazardous Waste Management Facility groundwater monitoring report, Third and fourth quarters 1995: Volume 1

International Nuclear Information System (INIS)

1996-03-01

Groundwater at the H-Area Hazardous Waste Management Facility (HWMF) is monitored in compliance with applicable regulations. Monitoring results are compared to the South Carolina Department of Health and Environmental control (SCDHEC) Groundwater Protection Standard (GWPS). Historically as well as currently, nitrate-nitrite as nitrogen, nonvolatile beta, and tritium have been among the primary constituents to exceed standards. Other radionuclides and hazardous constituents also exceeded the GWPS in the second half of 1995. Elevated constituents were found primarily in the water table (Aquifer Zone IIB 2 ), however, constitutents exceeding standards also occurred in several different aquifer zones monitoring wells. Water-level maps indicate that the groundwater flow rates and directions at the H-Area HWMF have remained relatively constant since the basins ceased to be active in 1988

Integrated Geo Hazard Management System in Cloud Computing Technology

Science.gov (United States)

Hanifah, M. I. M.; Omar, R. C.; Khalid, N. H. N.; Ismail, A.; Mustapha, I. S.; Baharuddin, I. N. Z.; Roslan, R.; Zalam, W. M. Z.

2016-11-01

Geo hazard can result in reducing of environmental health and huge economic losses especially in mountainous area. In order to mitigate geo-hazard effectively, cloud computer technology are introduce for managing geo hazard database. Cloud computing technology and it services capable to provide stakeholder's with geo hazards information in near to real time for an effective environmental management and decision-making. UNITEN Integrated Geo Hazard Management System consist of the network management and operation to monitor geo-hazard disaster especially landslide in our study area at Kelantan River Basin and boundary between Hulu Kelantan and Hulu Terengganu. The system will provide easily manage flexible measuring system with data management operates autonomously and can be controlled by commands to collects and controls remotely by using “cloud” system computing. This paper aims to document the above relationship by identifying the special features and needs associated with effective geohazard database management using “cloud system”. This system later will use as part of the development activities and result in minimizing the frequency of the geo-hazard and risk at that research area.

Kauai Test Facility hazards assessment document

Energy Technology Data Exchange (ETDEWEB)

Swihart, A

1995-05-01

The Department of Energy Order 55003A requires facility-specific hazards assessment be prepared, maintained, and used for emergency planning purposes. This hazards assessment document describes the chemical and radiological hazards associated with the Kauai Test Facility, Barking Sands, Kauai, Hawaii. The Kauai Test Facility`s chemical and radiological inventories were screened according to potential airborne impact to onsite and offsite individuals. The air dispersion model, ALOHA, estimated pollutant concentrations downwind from the source of a release, taking into consideration the toxicological and physical characteristics of the release site, the atmospheric conditions, and the circumstances of the release. The greatest distance to the Early Severe Health Effects threshold is 4.2 kilometers. The highest emergency classification is a General Emergency at the {open_quotes}Main Complex{close_quotes} and a Site Area Emergency at the Kokole Point Launch Site. The Emergency Planning Zone for the {open_quotes}Main Complex{close_quotes} is 5 kilometers. The Emergency Planning Zone for the Kokole Point Launch Site is the Pacific Missile Range Facility`s site boundary.

Kauai Test Facility hazards assessment document

International Nuclear Information System (INIS)

Swihart, A.

1995-05-01

The Department of Energy Order 55003A requires facility-specific hazards assessment be prepared, maintained, and used for emergency planning purposes. This hazards assessment document describes the chemical and radiological hazards associated with the Kauai Test Facility, Barking Sands, Kauai, Hawaii. The Kauai Test Facility's chemical and radiological inventories were screened according to potential airborne impact to onsite and offsite individuals. The air dispersion model, ALOHA, estimated pollutant concentrations downwind from the source of a release, taking into consideration the toxicological and physical characteristics of the release site, the atmospheric conditions, and the circumstances of the release. The greatest distance to the Early Severe Health Effects threshold is 4.2 kilometers. The highest emergency classification is a General Emergency at the open-quotes Main Complexclose quotes and a Site Area Emergency at the Kokole Point Launch Site. The Emergency Planning Zone for the open-quotes Main Complexclose quotes is 5 kilometers. The Emergency Planning Zone for the Kokole Point Launch Site is the Pacific Missile Range Facility's site boundary

78 FR 53190 - Pipeline Safety: Notice to Operators of Hazardous Liquid and Natural Gas Pipelines of a Recall on...

Science.gov (United States)

2013-08-28

... DEPARTMENT OF TRANSPORTATION Pipeline and Hazardous Materials Safety Administration [Docket No. PHMSA-2013-0185] Pipeline Safety: Notice to Operators of Hazardous Liquid and Natural Gas Pipelines of a Recall on Leak Repair Clamps Due to Defective Seal AGENCY: Pipeline and Hazardous Materials Safety...

[Powdered infant formulae preparation guide for hospitals based on Hazard Analysis and Critical Control Points (HACCP) principles].

Science.gov (United States)

Vargas-Leguás, H; Rodríguez Garrido, V; Lorite Cuenca, R; Pérez-Portabella, C; Redecillas Ferreiro, S; Campins Martí, M

2009-06-01

This guide for the preparation of powdered infant formulae in hospital environments is a collaborative work between several hospital services and is based on national and European regulations, international experts meetings and the recommendations of scientific societies. This guide also uses the Hazard Analysis and Critical Control Point principles proposed by Codex Alimentarius and emphasises effective verifying measures, microbiological controls of the process and the corrective actions when monitoring indicates that a critical control point is not under control. It is a dynamic guide and specifies the evaluation procedures that allow it to be constantly adapted.

Hanford fire department FY 99 annual work plan WBS 6.5.7

Energy Technology Data Exchange (ETDEWEB)

GOOD, D.E.

1999-02-24

The mission of the Hanford Fire Department (HFD) is to support the safe and timely cleanup of the Hanford site by providing a full range of services at the lowest possible cost to customers. These services include fire suppression, fire prevention, emergency rescue, emergency medical service, and hazardous materials response; and to be capable of dealing with and terminating emergency situations which could threaten the operations, employees, the general public, or interest of the U. S. Department of Energy operated Hanford Site. This includes response to surrounding fire departments/districts under mutual aid and state mobilization agreements and fire fighting, hazardous materials, and ambulance support to Washington Public Power Supply System (Supply System) and various commercial entities operating on site through Requests for Service from DOE-RL. The fire department also provides site fire marshal overview authority, fire system testing and maintenance, respiratory protection services, building tours and inspections, ignitable and reactive waste site inspections, prefire planning, and employee fire prevention education.

Hanford fire department FY 1999 annual work plan WBS 6.5.7

International Nuclear Information System (INIS)

GOOD, D.E.

1999-01-01

The mission of the Hanford Fire Department (HFD) is to support the safe and timely cleanup of the Hanford site by providing a full range of services at the lowest possible cost to customers. These services include fire suppression, fire prevention, emergency rescue, emergency medical service, and hazardous materials response; and to be capable of dealing with and terminating emergency situations which could threaten the operations, employees, the general public, or interest of the U. S. Department of Energy operated Hanford Site. This includes response to surrounding fire departments/districts under mutual aid and state mobilization agreements and fire fighting, hazardous materials, and ambulance support to Washington Public Power Supply System (Supply System) and various commercial entities operating on site through Requests for Service from DOE-RL. The fire department also provides site fire marshal overview authority, fire system testing and maintenance, respiratory protection services, building tours and inspections, ignitable and reactive waste site inspections, prefire planning, and employee fire prevention education

Readiness to implement Hazard Analysis and Critical Control Point (HACCP) systems in Iowa schools.

Science.gov (United States)

Henroid, Daniel; Sneed, Jeannie

2004-02-01

To evaluate current food-handling practices, food safety prerequisite programs, and employee knowledge and food safety attitudes and provide baseline data for implementing Hazard Analysis and Critical Control Point (HACCP) systems in school foodservice. One member of the research team visited each school to observe food-handling practices and assess prerequisite programs using a structured observation form. A questionnaire was used to determine employees' attitudes, knowledge, and demographic information. A convenience sample of 40 Iowa schools was recruited with input from the Iowa Department of Education. Descriptive statistics were used to summarize data. One-way analysis of variance was used to assess differences in attitudes and food safety knowledge among managers, cooks, and other foodservice employees. Multiple linear regression assessed the relationship between manager and school district demographics and the food safety practice score. Proper food-handling practices were not being followed in many schools and prerequisite food safety programs for HACCP were found to be inadequate for many school foodservice operations. School foodservice employees were found to have a significant amount of food safety knowledge (15.9+/-2.4 out of 20 possible points). School districts with managers (P=.019) and employees (P=.030) who had a food handler certificate were found to have higher food safety practice scores. Emphasis on implementing prerequisite programs in preparation for HACCP is needed in school foodservice. Training programs, both basic food safety such as ServSafe and HACCP, will support improvement of food-handling practices and implementation of prerequisite programs and HACCP.

78 FR 66326 - Hazardous Materials: Rail Petitions and Recommendations To Improve the Safety of Railroad Tank...

Science.gov (United States)

2013-11-05

...: Rail Petitions and Recommendations To Improve the Safety of Railroad Tank Car Transportation (RRR) AGENCY: Pipeline and Hazardous Materials Safety Administration (PHMSA), DOT. ACTION: Advance Notice of... DEPARTMENT OF TRANSPORTATION Pipeline and Hazardous Materials Safety Administration 49 CFR Parts...

[Quality management in emergency departments: Lack of uniform standards for fact-based controlling].

Science.gov (United States)

Ries, M; Christ, M

2015-11-01

The general high occupancy of emergency departments during the winter months of 2014/2015 outlined deficits in health politics. Whether on the regional, province, or federal level, verifiable and accepted figures to enable in depth analysis and fact-based controlling of emergency care systems are lacking. As the first step, reasons for the current situation are outlined in order to developed concrete recommendations for individual hospitals. This work is based on a selective literature search with focus on quality management, ratio driven management, and process management within emergency departments as well as personal experience with implementation of a key ratio system in a German maximum care hospital. The insufficient integration of emergencies into the DRG systematic, the role as gatekeeper between inpatient and outpatient care sector, the decentralized organization of emergency departments in many hospitals, and the inconsistent representation within the medical societies can be mentioned as reasons for the lack of key ratio systems. In addition to the important role within treatment procedures, emergency departments also have an immense economic importance. Consequently, the management of individual hospitals should promote implementation of key ratio systems to enable controlling of emergency care processes. Thereby the perspectives finance, employees, processes as well as partners and patients should be equally considered. Within the process perspective, milestones could be used to enable detailed controlling of treatment procedures. An implementation of key ratio systems without IT support is not feasible; thus, existing digital data should be used and future data analysis should already be considered during implementation of new IT systems.

Waste management facilities cost information for transportation of radioactive and hazardous materials

International Nuclear Information System (INIS)

Feizollahi, F.; Shropshire, D.; Burton, D.

1995-06-01

This report contains cost information on the U.S. Department of Energy (DOE) Complex waste streams that will be addressed by DOE in the programmatic environmental impact statement (PEIS) project. It describes the results of the task commissioned by DOE to develop cost information for transportation of radioactive and hazardous waste. It contains transportation costs for most types of DOE waste streams: low-level waste (LLW), mixed low-level waste (MLLW), alpha LLW and alpha MLLW, Greater-Than-Class C (GTCC) LLW and DOE equivalent waste, transuranic (TRU) waste, spent nuclear fuel (SNF), and hazardous waste. Unit rates for transportation of contact-handled ( 200 mrem/hr contact dose) radioactive waste are estimated. Land transportation of radioactive and hazardous waste is subject to regulations promulgated by DOE, the U.S. Department of Transportation (DOT), the U.S. Nuclear Regulatory Commission (NRC), and state and local agencies. The cost estimates in this report assume compliance with applicable regulations

Waste management facilities cost information for transportation of radioactive and hazardous materials

Energy Technology Data Exchange (ETDEWEB)

Feizollahi, F.; Shropshire, D.; Burton, D.

1995-06-01

This report contains cost information on the U.S. Department of Energy (DOE) Complex waste streams that will be addressed by DOE in the programmatic environmental impact statement (PEIS) project. It describes the results of the task commissioned by DOE to develop cost information for transportation of radioactive and hazardous waste. It contains transportation costs for most types of DOE waste streams: low-level waste (LLW), mixed low-level waste (MLLW), alpha LLW and alpha MLLW, Greater-Than-Class C (GTCC) LLW and DOE equivalent waste, transuranic (TRU) waste, spent nuclear fuel (SNF), and hazardous waste. Unit rates for transportation of contact-handled (<200 mrem/hr contact dose) and remote-handled (>200 mrem/hr contact dose) radioactive waste are estimated. Land transportation of radioactive and hazardous waste is subject to regulations promulgated by DOE, the U.S. Department of Transportation (DOT), the U.S. Nuclear Regulatory Commission (NRC), and state and local agencies. The cost estimates in this report assume compliance with applicable regulations.

Simulation Technology Laboratory Building 970 hazards assessment document

International Nuclear Information System (INIS)

Wood, C.L.; Starr, M.D.

1994-11-01

The Department of Energy Order 5500.3A requires facility-specific hazards assessments be prepared, maintained, and used for emergency planning purposes. This hazards assessment document describes the chemical and radiological hazards associated with the Simulation Technology Laboratory, Building 970. The entire inventory was screened according to the potential airborne impact to onsite and offsite individuals. The air dispersion model, ALOHA, estimated pollutant concentrations downwind from the source of a release, taking into consideration the toxicological and physical characteristics of the release site, the atmospheric conditions, and the circumstances of the release. The greatest distances at which a postulated facility event will produce consequences exceeding the ERPG-2 and Early Severe Health Effects thresholds are 78 and 46 meters, respectively. The highest emergency classification is a Site Area Emergency. The Emergency Planning Zone is 100 meters

Chemical health risk assessment for hazardous and mixed waste management units at Lawrence Livermore National Laboratory

International Nuclear Information System (INIS)

1992-09-01

The Lawrence Livermore National Laboratory (LLNL) operates three Hazardous Waste Management Facilities with 24 associated waste management units for the treatment and storage of hazardous and mixed wastes. These wastes are generated by research programs and support operations. The storage and treatment units are presently operated under interim status in accordance with the requirements of the US Envirorunental Protection Agency (US EPA) and the Department of Toxic Substances Control (DTSC), a division of the California Envirorunental Protection Agency (Cal/EPA). As required by the California Hazardous Waste Control Act and the Resource Conservation and Recovery Act (RCRA), LLNL ha s applied for a Part B permit to continue operating the storage and waste treatment facilities. As part of this permitting process, LLNL is required to conduct a health risk assessment (HRA) to examine the potential health impacts to the surrounding community from continued storage and treatment of hazardous and mixed wastes. analysis document presents the results of this risk assessment. An analysis of maximum credible chemical accidents is also included in Section 7.0. This HRA was prepared in accordance with procedures set forth by the California Air Pollution Control Officers Association (CAPCOA) ''Air Toxics Assessment Manual,'' CAPCOA guidelines for preparing risk assessments under the Air Toxic ''Hot Spots'' Act (AB 2588) and requirements of the US EPA. By following these procedures, this risk assessment presents a conservative analysis of a hypothetical Maximally Exposed Individual (MEI) using many worst-case assumptions that will not apply to an actual individual. As such, the risk estimates presented should be regarded as a worst-case estimate of any actual risk that may be present

Levels of and changes in life satisfaction predict mortality hazards: Disentangling the role of physical health, perceived control, and social orientation.

Science.gov (United States)

Hülür, Gizem; Heckhausen, Jutta; Hoppmann, Christiane A; Infurna, Frank J; Wagner, Gert G; Ram, Nilam; Gerstorf, Denis

2017-09-01

It is well documented that well-being typically evinces precipitous decrements at the end of life. However, research has primarily taken a postdictive approach by knowing the outcome (date of death) and aligning, in retrospect, how well-being has changed for people with documented death events. In the present study, we made use of a predictive approach by examining whether and how levels of and changes in life satisfaction prospectively predict mortality hazards and delineate the role of contributing factors, including health, perceived control, and social orientation. To do so, we applied shared parameter growth-survival models to 20-year longitudinal data from 10,597 participants (n = 1,560 [15%] deceased; age at baseline: M = 44 years, SD = 17, range = 18-98 years) from the national German Socio-Economic Panel Study. Our findings showed that lower levels and steeper declines of life satisfaction each uniquely predicted higher mortality risks. Results also revealed moderating effects of age and perceived control: Life satisfaction levels and changes had stronger predictive effects for mortality hazards among older adults. Perceived control was associated with lower mortality hazards; however, this effect was diminished for those who experienced accelerated life satisfaction decline. Variance decomposition suggests that predictive effects of life satisfaction trajectories were partially unique (3%-6%) and partially shared with physical health, perceived control, and social orientation (17%-19%). Our discussion focuses on the strengths and challenges of a predictive approach to link developmental changes (in life satisfaction) to mortality hazards, and considers implications of our findings for healthy aging. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

Preliminary proposed seismic design and evaluation criteria for new and existing underground hazardous materials storage tanks

International Nuclear Information System (INIS)

Kennedy, R.P.

1991-01-01

The document provides a recommended set of deterministic seismic design and evaluation criteria for either new or existing underground hazardous materials storage tanks placed in either the high hazard or moderate hazard usage catagories of UCRL-15910. The criteria given herein are consistent with and follow the same philosophy as those given in UCRL-15910 for the US Department of Energy facilities. This document is intended to supplement and amplify upon Reference 1 for underground hazardous materials storage tanks

The application of quality risk management to the bacterial endotoxins test: use of hazard analysis and critical control points.

Science.gov (United States)

Annalaura, Carducci; Giulia, Davini; Stefano, Ceccanti

2013-01-01

Risk analysis is widely used in the pharmaceutical industry to manage production processes, validation activities, training, and other activities. Several methods of risk analysis are available (for example, failure mode and effects analysis, fault tree analysis), and one or more should be chosen and adapted to the specific field where they will be applied. Among the methods available, hazard analysis and critical control points (HACCP) is a methodology that has been applied since the 1960s, and whose areas of application have expanded over time from food to the pharmaceutical industry. It can be easily and successfully applied to several processes because its main feature is the identification, assessment, and control of hazards. It can be also integrated with other tools, such as fishbone diagram and flowcharting. The aim of this article is to show how HACCP can be used to manage an analytical process, propose how to conduct the necessary steps, and provide data templates necessary to document and useful to follow current good manufacturing practices. In the quality control process, risk analysis is a useful tool for enhancing the uniformity of technical choices and their documented rationale. Accordingly, it allows for more effective and economical laboratory management, is capable of increasing the reliability of analytical results, and enables auditors and authorities to better understand choices that have been made. The aim of this article is to show how hazard analysis and critical control points can be used to manage bacterial endotoxins testing and other analytical processes in a formal, clear, and detailed manner.

LIFE CYCLE ASSESSMENT AND HAZARD ANALYSIS AND CRITICAL CONTROL POINTS TO THE PASTA PRODUCT

Directory of Open Access Journals (Sweden)

Yulexis Meneses Linares

2016-10-01

Full Text Available The objective of this work is to combine the Life Cycle Assessment (LCA and Hazard Analysis and Critical Control Points (HACCP methodologies for the determination of risks that the food production represents to the human health and the ecosystem. The environmental performance of the production of pastas in the “Marta Abreu” Pasta Factory of Cienfuegos is assessed, where the critical control points determined by the biological dangers (mushrooms and plagues and the physical dangers (wood, paper, thread and ferromagnetic particles were the raw materials: flour, semolina and its mixtures, and the disposition and extraction of them. Resources are the most affected damage category due to the consumption of fossil fuels.

Engineered Nanomaterials, Sexy New Technology and Potential Hazards

International Nuclear Information System (INIS)

Beaulieu, R.A.

2009-01-01

Engineered nanomaterials enhance exciting new applications that can greatly benefit society in areas of cancer treatments, solar energy, energy storage, and water purification. While nanotechnology shows incredible promise in these and other areas by exploiting nanomaterials unique properties, these same properties can potentially cause adverse health effects to workers who may be exposed during work. Dispersed nanoparticles in air can cause adverse health effects to animals not merely due to their chemical properties but due to their size, structure, shape, surface chemistry, solubility, carcinogenicity, reproductive toxicity, mutagenicity, dermal toxicity, and parent material toxicity. Nanoparticles have a greater likelihood of lung deposition and blood absorption than larger particles due to their size. Nanomaterials can also pose physical hazards due to their unusually high reactivity, which makes them useful as catalysts, but has the potential to cause fires and explosions. Characterization of the hazards (and potential for exposures) associated with nanomaterial development and incorporation in other products is an essential step in the development of nanotechnologies. Developing controls for these hazards are equally important. Engineered controls should be integrated into nanomaterial manufacturing process design according to 10CFR851, DOE Policy 456.1, and DOE Notice 456.1 as safety-related hardware or administrative controls for worker safety. Nanomaterial hazards in a nuclear facility must also meet control requirements per DOE standards 3009, 1189, and 1186. Integration of safe designs into manufacturing processes for new applications concurrent with the developing technology is essential for worker safety. This paper presents a discussion of nanotechnology, nanomaterial properties/hazards and controls

Hazard perception skills of young drivers with Attention Deficit Hyperactivity Disorder (ADHD) can be improved with computer based driver training: An exploratory randomised controlled trial.

Science.gov (United States)

Bruce, C R; Unsworth, C A; Dillon, M P; Tay, R; Falkmer, T; Bird, P; Carey, L M

2017-12-01

Young drivers with Attention Deficit Hyperactivity Disorder (ADHD) are at higher risk of road traffic injuries than their peers. Increased risk correlates with poor hazard perception skill. Few studies have investigated hazard perception training using computer technology with this group of drivers. *Determine the presence and magnitude of the between-group and within- subject change in hazard perception skills in young drivers with ADHD who receive Drive Smart training. *Determine whether training-facilitated change in hazard perception is maintained over time. This was a feasibility study, randomised control trial conducted in Australia. The design included a delayed treatment for the control group. Twenty-five drivers with a diagnosis of ADHD were randomised to the Immediate Intervention or Delayed Intervention group.The Immediate Intervention group received a training session using a computer application entitled Drive Smart. The Delayed Intervention group watched a documentary video initially (control condition), followed by the Drive Smart computer training session. The participant's hazard perception skill was measured using the Hazard Perception Test (HPT). After adjusting for baseline scores, there was a significant betweengroup difference in post-intervention HPT change scores in favour of the Immediate Intervention group. The magnitude of the effect was large. There was no significant within-group delayed intervention effect. A significant maintenance effect was found at 6-week follow-up for the Immediate Intervention group. The hazard perception skills of participants improved following training with large effect size and some maintenance of gain. A multimodal approach to training is indicated to facilitate maintenance. A full-scale trial is feasible. Copyright © 2017 Elsevier Ltd. All rights reserved.

Standard hazard analysis, critical control point and hotel management

Directory of Open Access Journals (Sweden)

Vujačić Vesna

2017-01-01

Full Text Available Tourism is a dynamic category which is continuously evolving in the world. Specificities that have to be respected in the execution in relation to the food industry are connected with the fact that the main differences which exist regarding the food serving procedure in catering, numerous complex recipes and production technologies, staff fluctuation, old equipment. For an effective and permanent implementation, the HACCP concept is very important for building a serious base. In this case, the base is represented by the people handling the food. This paper presents international ISO standards, the concept of HACCP and the importance of its application in the tourism and hospitality industry. The concept of HACCP is a food safety management system through the analysis and control of biological, chemical and physical hazards in the entire process, from raw material production, procurement, handling, to manufacturing, distribution and consumption of the finished product. The aim of this paper is to present the importance of the application of HACCP concept in tourism and hotel management as a recognizable international standard.

FIRE HAZARDS ANALYSIS - BUSTED BUTTE

International Nuclear Information System (INIS)

Longwell, R.; Keifer, J.; Goodin, S.

2001-01-01

The purpose of this fire hazards analysis (FHA) is to assess the risk from fire within individual fire areas at the Busted Butte Test Facility and to ascertain whether the DOE fire safety objectives are met. The objective, identified in DOE Order 420.1, Section 4.2, is to establish requirements for a comprehensive fire and related hazards protection program for facilities sufficient to minimize the potential for: (1) The occurrence of a fire related event. (2) A fire that causes an unacceptable on-site or off-site release of hazardous or radiological material that will threaten the health and safety of employees. (3) Vital DOE programs suffering unacceptable interruptions as a result of fire and related hazards. (4) Property losses from a fire and related events exceeding limits established by DOE. Critical process controls and safety class systems being damaged as a result of a fire and related events

Process hazards analysis (PrHA) program, bridging accident analyses and operational safety

International Nuclear Information System (INIS)

Richardson, J.A.; McKernan, S.A.; Vigil, M.J.

2003-01-01

Recently the Final Safety Analysis Report (FSAR) for the Plutonium Facility at Los Alamos National Laboratory, Technical Area 55 (TA-55) was revised and submitted to the US. Department of Energy (DOE). As a part of this effort, over seventy Process Hazards Analyses (PrHAs) were written and/or revised over the six years prior to the FSAR revision. TA-55 is a research, development, and production nuclear facility that primarily supports US. defense and space programs. Nuclear fuels and material research; material recovery, refining and analyses; and the casting, machining and fabrication of plutonium components are some of the activities conducted at TA-35. These operations involve a wide variety of industrial, chemical and nuclear hazards. Operational personnel along with safety analysts work as a team to prepare the PrHA. PrHAs describe the process; identi fy the hazards; and analyze hazards including determining hazard scenarios, their likelihood, and consequences. In addition, the interaction of the process to facility systems, structures and operational specific protective features are part of the PrHA. This information is rolled-up to determine bounding accidents and mitigating systems and structures. Further detailed accident analysis is performed for the bounding accidents and included in the FSAR. The FSAR is part of the Documented Safety Analysis (DSA) that defines the safety envelope for all facility operations in order to protect the worker, the public, and the environment. The DSA is in compliance with the US. Code of Federal Regulations, 10 CFR 830, Nuclear Safety Management and is approved by DOE. The DSA sets forth the bounding conditions necessary for the safe operation for the facility and is essentially a 'license to operate.' Safely of day-to-day operations is based on Hazard Control Plans (HCPs). Hazards are initially identified in the PrI-IA for the specific operation and act as input to the HCP. Specific protective features important to worker

Radiation Hazard Detector

Science.gov (United States)

1978-01-01

NASA technology has made commercially available a new, inexpensive, conveniently-carried device for protection, of people exposed to potentially dangerous levels of microwave radiation. Microwaves are radio emissions of extremely high frequency. They can be hazardous but the degree of hazard is not yet well understood. Generally, it is believed that low intensity radiation of short duration is not harmful but that exposure to high levels can induce deep internal burns, affecting the circulatory and nervous systems, and particularly the eyes. The Department of Labor's Occupational Safety and Health Administration (OSHA) has established an allowable safe threshold of exposure. However, people working near high intensity sources of microwave energy-for example, radar antennas and television transmitters-may be unknowingly exposed to radiation levels beyond the safe limit. This poses not only a personal safety problem but also a problem for employers in terms of productivity loss, workman's compensation claims and possible liability litigation. Earlier-developed monitoring devices which warn personnel of dangerous radiation levels have their shortcomings. They can be cumbersome and awkward to use while working. They also require continual visual monitoring to determine if a person is in a dangerous area of radiation, and they are relatively expensive, another deterrent to their widespread adoption. In response to the need for a cheaper and more effective warning system, Jet Propulsion Laboratory developed, under NASA auspices, a new, battery-powered Microwave Radiation Hazard Detector. To bring the product to the commercial market, California Institute Research Foundation, the patent holder, granted an exclusive license to Cicoil Corporation, Chatsworth, California, an electronic components manufacturer.

Sandia Administrative Micrographics Facility, Building 802: Hazards assessment document

International Nuclear Information System (INIS)

Swihart, A.

1994-12-01

The Department of Energy Order 5500.3A requires facility-specific hazards assessments be prepared, maintained, and used for emergency planning purposes. This hazards assessment document describes the chemical and radiological hazards associated with the Sandia Administrative Micrographics Facility, Building 802. The entire inventory was screened according to the potential airborne impact to onsite and offsite individuals. The air dispersion model, ALOHA, estimated pollutant concentrations downwind from the source of a release, taking into consideration the toxicological and physical characteristics of the release site, the atmospheric conditions, and the circumstances of the release. The greatest distance at which a postulated facility event will produce consequences exceeding the Early Severe Health Effects threshold is 33 meters. The highest emergency classification is a Site Area Emergency. The Emergency Planning Zone is 75 meters

Climate Prediction Center(CPC)Global Tropics Hazards and Benefits Assessment

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Global Tropics Hazards and Benefits Assessment (GTH) is an outlook product for the areas in the Tropics. Forecasts for the Week-1 and Week-2 period are given for...

US Department of Energy radiological control manual. Revision 1

Energy Technology Data Exchange (ETDEWEB)

1994-04-01

This manual establishes practices for the conduct of Department of Energy radiological control activities. The Manual states DOE`s positions and views on the best courses of action currently available in the area of radiological controls. Accordingly, the provisions in the Manual should be viewed by contractors as an acceptable technique, method or solution for fulfilling their duties and responsibilities. This Manual shall be used by DOE in evaluating the performance of its contractors. This Manual is not a substitute for Regulations; it is intended to be consistent with all relevant statutory and regulatory requirements and shall be revised whenever necessary to ensure such consistency. Some of the Manual provisions, however, challenge the user to go well beyond minimum requirements. Following the course of action delineated in the Manual will result in achieving and surpassing related statutory or regulatory requirements.

Hazardous Waste Remedial Actions Program annual progress report, FY 1990

Energy Technology Data Exchange (ETDEWEB)

1990-12-01

The Hazardous Waste Remedial Actions Programs (HAZWRAP), a unit of Martin Marietta Energy Systems, Inc., supports the Department of Energy (DOE) Oak Ridge Operations Office in broadly environmental areas, especially those relating to waste management and environmental restoration. HAZWRAP comprises six program areas, which are supported by central administrative and technical organizations. Existing programs deal with airborne hazardous substances, pollution prevention, remedial actions planning, environmental restoration, technology development, and information and data systems. HAZWRAP's mission to develop, promote, and apply-cost-effective hazardous waste management and environmental technologies to help solve national problems and concerns. HAZWRAP seeks to serve as integrator for hazardous waste and materials management across the federal government. It applies the unique combination of research and development (R D) capabilities, technologies, management expertise, and facilities in the Energy Systems complex to address problems of national importance. 24 figs., 10 tabs.

F-Area Hazardous Waste Management Facility groundwater monitoring report, Third and fourth quarters 1995: Volume 1

International Nuclear Information System (INIS)

1996-03-01

Groundwater at the F-Area Hazardous Waste Management Facility (HWMF) is monitored in compliance with applicable regulations. Monitoring results are compared to the South Carolina Department of Health and Environmental Control (SCDHEC) Groundwater Protection Standard (GWPS). Historically and currently, gross alpha, nitrates, nonvolatile beta, and tritium are among the primary constituents to exceed standards. Numerous other radionuclides and hazardous constituents also exceed the GWPS in the groundwater during the second half of 1995, notably cadmium, lead, radium-226, radium-228, strontium-90, and total alpha-emitting radium. The elevated constituents were found primarily in the water table (aquifer zone IIB 2 ), however, several other aquifer unit monitoring wells contained elevated levels of constituents. Water-level maps indicate that the groundwater flow rates and directions at the F-Area HWMF have remained relatively constant since the basins ceased to be active in 1988

The Hazardous-Drums Project: A Multiweek Laboratory Exercise for General Chemistry Involving Environmental, Quality Control, and Cost Evaluation

Science.gov (United States)

Hayes, David; Widanski, Bozena

2013-01-01

A laboratory experiment is described that introduces students to "real-world" hazardous waste management issues chemists face. The students are required to define an analytical problem, choose a laboratory analysis method, investigate cost factors, consider quality-control issues, interpret the meaning of results, and provide management…

DynCorp Tricities Services, Inc. Hanford fire department FY 1998 annual work plan

International Nuclear Information System (INIS)

Good, D.E.

1997-01-01

The mission of the Hanford Fire Department (HFD) is to support the safe and timely cleanup of the Hanford site by providing fire suppression, fire prevention, emergency rescue, emergency medical service, and hazardous materials response; and to be capable of dealing with and terminating emergency situations which could threaten the operations, employees, or interest of the U.S. Department of Energy operated Hanford site. This includes response to surrounding fire departments/districts under mutual aid and state mobilization agreements and fire fighting, hazardous materials, and ambulance support to Washington Public Power Supply System (Supply System) and various commercial entities operating on site through Requests for Service from DOE-RL. This fire department also provides site fire marshal overview authority, fire system testing and maintenance, respiratory protection services, building tours and inspections, ignitable and reactive waste site inspections, prefire planning, and employee fire prevention education. This plan provides a program overview, program baselines, and schedule baseline

Fire protection program fiscal year 1995 site support program plan, Hanford Fire Department

International Nuclear Information System (INIS)

Good, D.E.

1994-09-01

The mission of the Hanford Fire Department (HFD) is to support the safe and timely cleanup of the Hanford site by providing fire suppression, fire prevention, emergency rescue, emergency medical service, and hazardous materials response; and to be capable of dealing with and terminating emergency situations which could threaten the operations, employees, or interest of the US Department of Energy operated Hanford Site. This includes response to surrounding fire departments/districts under a mutual aid agreement and contractual fire fighting, hazardous materials, and ambulance support to Washington Public Power Supply System (Supply System). The fire department also provides site fire marshal overview authority, fire system testing and maintenance, self-contained breathing apparatus maintenance, building tours and inspections, ignitable and reactive waste site inspections, prefire planning, and employee fire prevention education. This report describes the specific responsibilities and programs that the HFD must support and the estimated cost of this support for FY1995

Using an information system to meet Hazardous Waste Management needs

International Nuclear Information System (INIS)

Stewart, J.J. Jr.; Howe, R.E.; Townsend, S.L.; Maloy, D.T.; Kochhar, R.K.

1995-02-01

Lawrence Livermore National Laboratory (LLNL) is a large quantity RCRA hazardous waste generator. LLNL also generates low level and transuranic radioactive waste that is managed in accordance with the Department of Energy (DOE) orders. The mixed low level and mixed transuranic waste generated must be managed to comply with both RCRA regulations and DOE orders. LLNL's hazardous and radioactive waste generation is comprised of 900 generators who contribute to nearly two hundred waste streams. LLNL has a permitted EPA treatment and storage (TSD) facility for handling RCRA hazardous waste that is operated by LLNL's Hazardous Waste Management (HWM) division. In HWM we have developed an information system, the Total Waste Management System (TWMS), to replace an inadequate ''cradle to grave'' tracking of all the waste types described above. The goals of this system are to facilitate the safe handling and storage of these hazardous wastes, provide compliance with the regulations and serve as an informational tool to help HWM manage and dispose of these wastes in a cost effective manner

Fire hazards analysis for the uranium oxide (UO3) facility

International Nuclear Information System (INIS)

Wyatt, D.M.

1994-01-01

The Fire Hazards Analysis (FHA) documents the deactivation end-point status of the UO 3 complex fire hazards, fire protection and life safety systems. This FHA has been prepared for the Uranium Oxide Facility by Westinghouse Hanford Company in accordance with the criteria established in DOE 5480.7A, Fire Protection and RLID 5480.7, Fire Protection. The purpose of the Fire Hazards Analysis is to comprehensively and quantitatively assess the risk from a fire within individual fire areas in a Department of Energy facility so as to ascertain whether the objectives stated in DOE Order 5480.7, paragraph 4 are met. Particular attention has been paid to RLID 5480.7, Section 8.3, which specifies the criteria for deactivating fire protection in decommission and demolition facilities

Major hazards onshore and offshore

International Nuclear Information System (INIS)

1992-01-01

This symposium continues the tradition of bringing together papers on a topic of current interest and importance in terms of process safety - in this case, Major Hazards Onshore and Offshore. Lord Cullen in his report on the Piper Alpha disaster has, in effect, suggested that the experience gained in the control of major hazards onshore during the 1980s should be applied to improve safety offshore during the 1990s. This major three-day symposium reviews what has been learned so far with regard to major hazards and considers its present and future applications both onshore and offshore. The topics covered in the programme are wide ranging and deal with all aspects of legislation, the application of regulations, techniques for evaluating hazards and prescribing safety measures in design, construction and operation, the importance of the human factors, and recent technical developments in protective measures, relief venting and predicting the consequences of fires and explosions. (author)

Geologic Maps as the Foundation of Mineral-Hazards Maps in California

Science.gov (United States)

Higgins, C. T.; Churchill, R. K.; Downey, C. I.; Clinkenbeard, J. P.; Fonseca, M. C.

2010-12-01

The basic geologic map is essential to the development of products that help planners, engineers, government officials, and the general public make decisions concerning natural hazards. Such maps are the primary foundation that the California Geological Survey (CGS) uses to prepare maps that show potential for mineral-hazards. Examples of clients that request these maps are the California Department of Transportation (Caltrans) and California Department of Public Health (CDPH). Largely because of their non-catastrophic nature, mineral hazards have received much less public attention compared to earthquakes, landslides, volcanic eruptions, and floods. Nonetheless, mineral hazards can be a major concern locally when considering human health and safety and potential contamination of the environment by human activities such as disposal of earth materials. To address some of these concerns, the CGS has focused its mineral-hazards maps on naturally occurring asbestos (NOA), radon, and various potentially toxic metals as well as certain artificial features such as mines and oil and gas wells. The maps range in scope from statewide to counties and Caltrans districts to segments of selected highways. To develop the hazard maps, the CGS begins with traditional paper and digital versions of basic geologic maps, which are obtained from many sources such as its own files, the USGS, USDA Forest Service, California Department of Water Resources, and counties. For each study area, these maps present many challenges of compilation related to vintage, scale, definition of units, and edge-matching across map boundaries. The result of each CGS compilation is a digital geologic layer that is subsequently reinterpreted and transformed into new digital layers (e.g., lithologic) that focus on the geochemical and mineralogical properties of the area’s earth materials and structures. These intermediate layers are then integrated with other technical data to derive final digital layers

Modeling and Hazard Analysis Using STPA

Science.gov (United States)

Ishimatsu, Takuto; Leveson, Nancy; Thomas, John; Katahira, Masa; Miyamoto, Yuko; Nakao, Haruka

2010-09-01

A joint research project between MIT and JAXA/JAMSS is investigating the application of a new hazard analysis to the system and software in the HTV. Traditional hazard analysis focuses on component failures but software does not fail in this way. Software most often contributes to accidents by commanding the spacecraft into an unsafe state(e.g., turning off the descent engines prematurely) or by not issuing required commands. That makes the standard hazard analysis techniques of limited usefulness on software-intensive systems, which describes most spacecraft built today. STPA is a new hazard analysis technique based on systems theory rather than reliability theory. It treats safety as a control problem rather than a failure problem. The goal of STPA, which is to create a set of scenarios that can lead to a hazard, is the same as FTA but STPA includes a broader set of potential scenarios including those in which no failures occur but the problems arise due to unsafe and unintended interactions among the system components. STPA also provides more guidance to the analysts that traditional fault tree analysis. Functional control diagrams are used to guide the analysis. In addition, JAXA uses a model-based system engineering development environment(created originally by Leveson and called SpecTRM) which also assists in the hazard analysis. One of the advantages of STPA is that it can be applied early in the system engineering and development process in a safety-driven design process where hazard analysis drives the design decisions rather than waiting until reviews identify problems that are then costly or difficult to fix. It can also be applied in an after-the-fact analysis and hazard assessment, which is what we did in this case study. This paper describes the experimental application of STPA to the JAXA HTV in order to determine the feasibility and usefulness of the new hazard analysis technique. Because the HTV was originally developed using fault tree analysis

Frozen soil barriers for hazardous waste confinement

International Nuclear Information System (INIS)

Dash, J.G.; Leger, R.; Fu, H.Y.

1997-01-01

Laboratory and full field measurements have demonstrated the effectiveness of artificial ground freezing for the containment of subsurface hazardous and radioactive wastes. Bench tests and a field demonstration have shown that cryogenic barriers are impenetrable to aqueous and non aqueous liquids. As a result of the successful tests the US Department of Energy has designated frozen ground barriers as one of its top ten remediation technologies

Assessment of mixed hazardous and radioactive waste sites at Hanford

International Nuclear Information System (INIS)

McLaughlin, T.J.; Cramer, K.H.; Lamar, D.A.; Sherwood, D.R.; Stenner, R.D.; Schulze, W.B.

1987-10-01

The US Department of Energy and Pacific Northwest Laboratory recently completed a preliminary assessment of 685 inactive hazardous waste sites located on the Hanford Site. The preliminary assessment involved collecting historical data and individual site information, conducting site inspections, and establishing an environmental impact priority, using the Hazard Ranking System, for each of these 685 sites. This preliminary assessment was the first step in the remediation process required by the Comprehensive Environmental Response, Compensation and Liability Act. This paper presents the results of that preliminary assessment. 10 refs., 4 figs., 1 tab

Occupational hazards to health of port workers.

Science.gov (United States)

Wang, Yukun; Zhan, Shuifen; Liu, Yan; Li, Yan

2017-12-01

The aim of this article is to reduce the risk of occupational hazards and improve safety conditions by enhancing hazard knowledge and identification as well as improving safety behavior for freight port enterprises. In the article, occupational hazards to health and their prevention measures of freight port enterprises have been summarized through a lot of occupational health evaluation work, experience and understanding. Workers of freight port enterprises confront an equally wide variety of chemical, physical and psychological hazards in production technology, production environment and the course of labor. Such health hazards have been identified, the risks evaluated, the dangers to health notified and effective prevention measures which should be put in place to ensure the health of the port workers summarized. There is still a long way to go for the freight port enterprises to prevent and control the occupational hazards. Except for occupational hazards and their prevention measures, other factors that influence the health of port workers should also be paid attention to, such as age, work history, gender, contraindication and even the occurrence and development rules of occupational hazards in current production conditions.

The Hazardous Waste/Mixed Waste Disposal Facility

International Nuclear Information System (INIS)

Bailey, L.L.

1991-01-01

The Hazardous Waste/Mixed Waste Disposal Facility (HW/MWDF) will provide permanent Resource Conservation and Recovery Act (RCRA) permitted storage, treatment, and disposal for hazardous and mixed waste generated at the Department of Energy's (DOE) Savannah River Site (SRS) that cannot be disposed of in existing or planned SRS facilities. Final design is complete for Phase I of the project, the Disposal Vaults. The Vaults will provide RCRA permitted, above-grade disposal capacity for treated hazardous and mixed waste generated at the SRS. The RCRA Part B Permit application was submitted upon approval of the Permit application, the first Disposal Vault is scheduled to be operational in mid 1994. The technical baseline has been established for Phase II, the Treatment Building, and preliminary design work has been performed. The Treatment Building will provide RCRA permitted treatment processes to handle a variety of hazardous and mixed waste generated at SRS in preparation for disposal. The processes will treat wastes for disposal in accordance with the Environmental Protection Agency's (EPA's) Land Disposal Restrictions (LDR). A RCRA Part B Permit application has not yet been submitted to SCDHEC for this phase of the project. The Treatment Building is currently scheduled to be operational in late 1996

QMRA (quantitative microbial risk assessment) and HACCP (hazard analysis and critical control points) for management of pathogens in wastewater and sewage sludge treatment and reuse.

Science.gov (United States)

Westrell, T; Schönning, C; Stenström, T A; Ashbolt, N J

2004-01-01

Hazard Analysis and Critical Control Points (HACCP) was applied for identifying and controlling exposure to pathogenic microorganisms encountered during normal sludge and wastewater handling at a 12,500 m3/d treatment plant utilising tertiary wastewater treatment and mesophilic sludge digestion. The hazardous scenarios considered were human exposure during treatment, handling, soil application and crop consumption, and exposure via water at the wetland-area and recreational swimming. A quantitative microbial risk assessment (QMRA), including rotavirus, adenovirus, haemorrhagic E. coli, Salmonella, Giardia and Cryptosporidium, was performed in order to prioritise pathogen hazards for control purposes. Human exposures were treated as individual risks but also related to the endemic situation in the general population. The highest individual health risk from a single exposure was via aerosols for workers at the belt press for sludge dewatering (virus infection risk = 1). The largest impact on the community would arise if children ingested sludge at the unprotected storage site, although in the worst-case situation the largest number of infections would arise through vegetables fertilised with sludge and eaten raw (not allowed in Sweden). Acceptable risk for various hazardous scenarios, treatment and/or reuse strategies could be tested in the model.

Development of treatment technologies for the processing of US Department of Energy mixed waste

International Nuclear Information System (INIS)

Backus, P.M.; Berry, J.B.; Coyle, G.J.; Lurk, P.W.; Wolf, S.M.

1993-01-01

Waste contaminated with chemically hazardous and radioactive species is defined as mixed waste. Significant technology development has been conducted for separate treatment of hazardous and radioactive waste, but technology development addressing mixed-waste treatment has been limited. Management of mixed waste requires treatment which must meet the standards established by the US Environmental Protection Agency for the specific hazardous constituents while also providing adequate control of the radionuclides. Technology has not been developed, demonstrated, or tested to produce a low-risk final waste form specifically for mixed waste. Throughout the US Department of Energy (DOE) complex, mixed waste is a problem because definitive treatment standards have not been established and few disposal facilities are available. Treatment capability and capacity are also limited. Site-specific solutions to the management of mixed waste have been initiated; however, site-specific programs result in duplication of technology development between various sites. Significant progress is being made in developing technology for mixed waste under the Mixed Waste Integrated Program. The status of the technical initiatives in chemical/physical treatment, destruction/stabilization technology, off-gas treatment, and final waste form production/assessment is described in this paper

Application of Hazard Analysis and Critical Control Points (HACCP) to the Cultivation Line of Mushroom and Other Cultivated Edible Fungi.

Science.gov (United States)

Pardo, José E; de Figueirêdo, Vinícius Reis; Alvarez-Ortí, Manuel; Zied, Diego C; Peñaranda, Jesús A; Dias, Eustáquio Souza; Pardo-Giménez, Arturo

2013-09-01

The Hazard analysis and critical control points (HACCP) is a preventive system which seeks to ensure food safety and security. It allows product protection and correction of errors, improves the costs derived from quality defects and reduces the final overcontrol. In this paper, the system is applied to the line of cultivation of mushrooms and other edible cultivated fungi. From all stages of the process, only the reception of covering materials (stage 1) and compost (stage 3), the pre-fruiting and induction (step 6) and the harvest (stage 7) have been considered as critical control point (CCP). The main hazards found were the presence of unauthorized phytosanitary products or above the permitted dose (stages 6 and 7), and the presence of pathogenic bacteria (stages 1 and 3) and/or heavy metals (stage 3). The implementation of this knowledge will allow the self-control of their productions based on the system HACCP to any plant dedicated to mushroom or other edible fungi cultivation.

Preliminary fire hazards analysis for W-211, Initial Tank Retrieval Systems

International Nuclear Information System (INIS)

Huckfeldt, R.A.

1995-01-01

A fire hazards analysis (FHA) was performed for Project W-211, Initial Tank Retrieval System (ITRS), at the Department of Energy (DOE) Hanford site. The objectives of this FHA was to determine (1) the fire hazards that expose the Initial Tank Retrieval System or are inherent in the process, (2) the adequacy of the fire-safety features planned, and (3) the degree of compliance of the project with specific fire safety provisions in DOE orders and related engineering codes and standards. The scope included the construction, the process hazards, building fire protection, and site wide fire protection. The results are presented in terms of the fire hazards present, the potential extent of fire damage, and the impact on employees and public safety. This study evaluated the ITRS with respect to its use at Tank 241-SY-101 only

Calculation of Hazard Category 2/3 Threshold Quantities Using Contemporary Dosimetric Data

Energy Technology Data Exchange (ETDEWEB)

Walker, William C. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2017-11-01

The purpose of this report is to describe the methodology and selection of input data utilized to calculate updated Hazard Category 2 and Hazard Category 3 Threshold Quantities (TQs) using contemporary dosimetric information. The calculation of the updated TQs will be considered for use in the revision to the Department of Energy (DOE) Technical Standard (STD-) 1027-92 Change Notice (CN)-1, “Hazard Categorization and Accident Analysis Techniques for Compliance with DOE Order 5480.23, Nuclear Safety Analysis Reports.” The updated TQs documented in this report complement an effort previously undertaken by the National Nuclear Security Administration (NNSA), which in 2014 issued revised Supplemental Guidance documenting the calculation of updated TQs for approximately 100 radionuclides listed in DOE-STD-1027-92, CN-1. The calculations documented in this report complement the NNSA effort by expanding the set of radionuclides to more than 1,250 radionuclides with a published TQ. The development of this report was sponsored by the Department of Energy’s Office of Nuclear Safety (AU-30) within the Associate Under Secretary for Environment, Health, Safety, and Security organization.

Application of the FTA and ETA Method for Gas Hazard Identification for the Performance of Safety Systems in the Industrial Department

Science.gov (United States)

Ignac-Nowicka, Jolanta

2018-03-01

The paper analyzes the conditions of safe use of industrial gas systems and factors influencing gas hazards. Typical gas installation and its basic features have been characterized. The results of gas threat analysis in an industrial enterprise using FTA error tree method and ETA event tree method are presented. Compares selected methods of identifying hazards gas industry with respect to the scope of their use. The paper presents an analysis of two exemplary hazards: an industrial gas catastrophe (FTA) and an explosive gas explosion (ETA). In both cases, technical risks and human errors (human factor) were taken into account. The cause-effect relationships of hazards and their causes are presented in the form of diagrams in the drawings.

Hazard waste risk assessment

International Nuclear Information System (INIS)

Hawley, K.A.; Napier, B.A.

1986-01-01

Pacific Northwest Laboratory continued to provide technical assistance to the Department of Energy (DOE) Office of Operational Safety (OOS) in the area of risk assessment for hazardous and radioactive-mixed waste management. The overall objective is to provide technical assistance to OOS in developing cost-effective risk assessment tools and strategies for bringing DOE facilities into compliance with the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA or Superfund) and the Resource Conservation and Recovery Act (RCRA). Major efforts during FY 1985 included (1) completing the modification of the Environmental Protection Agency (EPA) Hazard Ranking System (HRS) and developing training manuals and courses to assist in field office implementation of the modified Hazard Ranking System (mHRS); (2) initiating the development of a system for reviewing field office HRS/mHRS evaluations for appropriate use of data and appropriate application of the methodology; (3) initiating the development of a data base management system to maintain all field office HRS/mHRS scoring sheets and to support the master OOS environmental data base system; (4) developing implementation guidance for Phase I of the DOE CERCLA Program, Installation Assessment; (5) continuing to develop an objective, scientifically based methodology for DOE management to use in establishing priorities for conducting site assessments under Phase II of the DOE CERCLA Program, Confirmation; and (6) participating in developing the DOE response to EPA on the proposed listing of three sites on the National Priorities List

Hazard function theory for nonstationary natural hazards

Science.gov (United States)

Read, L.; Vogel, R. M.

2015-12-01

Studies from the natural hazards literature indicate that many natural processes, including wind speeds, landslides, wildfires, precipitation, streamflow and earthquakes, show evidence of nonstationary behavior such as trends in magnitudes through time. Traditional probabilistic analysis of natural hazards based on partial duration series (PDS) generally assumes stationarity in the magnitudes and arrivals of events, i.e. that the probability of exceedance is constant through time. Given evidence of trends and the consequent expected growth in devastating impacts from natural hazards across the world, new methods are needed to characterize their probabilistic behavior. The field of hazard function analysis (HFA) is ideally suited to this problem because its primary goal is to describe changes in the exceedance probability of an event over time. HFA is widely used in medicine, manufacturing, actuarial statistics, reliability engineering, economics, and elsewhere. HFA provides a rich theory to relate the natural hazard event series (x) with its failure time series (t), enabling computation of corresponding average return periods and reliabilities associated with nonstationary event series. This work investigates the suitability of HFA to characterize nonstationary natural hazards whose PDS magnitudes are assumed to follow the widely applied Poisson-GP model. We derive a 2-parameter Generalized Pareto hazard model and demonstrate how metrics such as reliability and average return period are impacted by nonstationarity and discuss the implications for planning and design. Our theoretical analysis linking hazard event series x, with corresponding failure time series t, should have application to a wide class of natural hazards.

Hazard function theory for nonstationary natural hazards

Science.gov (United States)

Read, Laura K.; Vogel, Richard M.

2016-04-01

Impact from natural hazards is a shared global problem that causes tremendous loss of life and property, economic cost, and damage to the environment. Increasingly, many natural processes show evidence of nonstationary behavior including wind speeds, landslides, wildfires, precipitation, streamflow, sea levels, and earthquakes. Traditional probabilistic analysis of natural hazards based on peaks over threshold (POT) generally assumes stationarity in the magnitudes and arrivals of events, i.e., that the probability of exceedance of some critical event is constant through time. Given increasing evidence of trends in natural hazards, new methods are needed to characterize their probabilistic behavior. The well-developed field of hazard function analysis (HFA) is ideally suited to this problem because its primary goal is to describe changes in the exceedance probability of an event over time. HFA is widely used in medicine, manufacturing, actuarial statistics, reliability engineering, economics, and elsewhere. HFA provides a rich theory to relate the natural hazard event series (X) with its failure time series (T), enabling computation of corresponding average return periods, risk, and reliabilities associated with nonstationary event series. This work investigates the suitability of HFA to characterize nonstationary natural hazards whose POT magnitudes are assumed to follow the widely applied generalized Pareto model. We derive the hazard function for this case and demonstrate how metrics such as reliability and average return period are impacted by nonstationarity and discuss the implications for planning and design. Our theoretical analysis linking hazard random variable X with corresponding failure time series T should have application to a wide class of natural hazards with opportunities for future extensions.

Hazardous-environment problems: Mobile robots to the rescue

International Nuclear Information System (INIS)

Meieran, H.B.

1992-01-01

This paper presents a rationale for employing a spectrum of similar mobile robots to conduct appropriate common missions for the following five hazardous-environment issues: (1) dismantlement of nuclear weapons; (2) environmental restoration and waste management of US Department of Energy weapons sites; (3) operations in nuclear power plants and other facilities; (4) waste chemical site remediation and cleanup activities; and (5) assistance in handling toxic chemical/radiation accidents. Mobile robots have been developed for several hazardous-environment industries, the most visible ones being construction/excavation/tunneling, explosive ordnance/bomb disposal (EOD), fire-fighting, military operations, mining, nuclear, and security. A summary of the range of functions that mobile robots are currently capable of conducting is presented

Hazardous Waste Remedial Actions Program: integrating waste management

International Nuclear Information System (INIS)

Petty, J.L.; Sharples, F.E.

1986-01-01

The Hazardous Waste Remedial Actions Program was established to integrate Defense Programs' activities in hazardous and mixed waste management. The Program currently provides centralized planning and technical support to the Office of the Assistant Secretary for Defense Programs. More direct project management responsibilities may be assumed in the future. The Program, under the direction of the ASDP's Office of Defense Waste and Transportation Management, interacts with numerous organizational entities of the Department. The Oak Ridge Operations Office has been designated as the Lead Field Office. The Program's four current components cover remedial action project identification and prioritization; technology adaptation; an informative system; and a strategy study for long-term, ''corporate'' project and facility planning

Hazard Monitoring in a Spectrum-Challenged Future: US Department of Transportation Adjacent Band Compatibility Assessment of Interference on High-Precision GNSS Receivers

Science.gov (United States)

Blume, F.; Berglund, H. T.

2016-12-01

In 2012 the Federal Communications Commission (FCC) reversed its decision to allow communications company LightSquared to use GPS-adjacent spectrum for a ground based network after testing demonstrated harmful interference to GPS receivers. Now rebranded as Ligado, they have submitted modified application to use a smaller portion of the L-band spectrum at much lower power. Many GPS community stakeholders, including the hazard monitoring and EEW communities remain concerned that Ligado's proposed use could still cause harmful interference, causing signal degradation, real-time positioning errors, and total failure of GNSS hardware in widespread use in hazard monitoring networks. The Department of Transportation (DoT) has conducted hardware tests to determine adjacent-band transmitter power limit criteria that would prevent harmful interference from Ligado's operations. We present preliminary results produced from the data collected by the three UNAVCO receiver types tested: Trimble NetRS, Trimble NetR9, and Septentrio PolaRx5. In the first round of testing, simulated GNSS signals were broadcast in an anechoic chamber (pictured below) while interfering signals are broadcast simultaneously with varying amplitude and frequency. The older GPS-only NetRS receiver showed smaller reductions in SNR at frequencies adjacent to GPS L1 as compared to the other receivers, suggesting narrower L1 filter bandwidth in the RF frontend. The NetR9 showed greater decreases in observed SNR in the 1615 to 1625 MHz range when compared to the other two receivers. This suggests that the NetR9's L1 filter bandwidth has been increased to accommodate GNSS signals. Linearity tests were conducted to better relate SNR measurements between receiver types. The PolaRx5 receiver showed less SNR variation between tracking channels than both Trimble receivers. Our results show the power levels at which adjacent-band interference begins degrading receiver performance and eventually disables tracking. As

Hazards assessment for the Hazardous Waste Storage Facility

International Nuclear Information System (INIS)

Knudsen, J.K.; Calley, M.B.

1994-04-01

This report documents the hazards assessment for the Hazardous Waste Storage Facility (HWSF) located at the Idaho National Engineering Laboratory. The hazards assessment was performed to ensure that this facility complies with DOE and company requirements pertaining to emergency planning and preparedness for operational emergencies. The hazards assessment identifies and analyzes hazards that are significant enough to warrant consideration in a facility's operational emergency management program. The area surrounding HWSF, the buildings and structures at HWSF, and the processes used at HWSF are described in this report. All nonradiological hazardous materials at the HWSF were identified (radiological hazardous materials are not stored at HWSF) and screened against threshold quantities according to DOE Order 5500.3A guidance. Two of the identified hazardous materials exceeded their specified threshold quantity. This report discusses the potential release scenarios and consequences associated with an accidental release for each of the two identified hazardous materials, lead and mercury. Emergency considerations, such as emergency planning zones, emergency classes, protective actions, and emergency action levels, are also discussed based on the analysis of potential consequences. Evaluation of the potential consequences indicated that the highest emergency class for operational emergencies at the HWSF would be a Site Area Emergency

Emergency preparedness hazards assessment for the Concentrate, Storage and Transfer Facility

International Nuclear Information System (INIS)

Blanchard, A.

2000-01-01

This report documents this facility Emergency Preparedness Hazards Assessment (EPHA) for the Concentrate, Storage and Transfer Facility (CSTF) located on the Department of Energy (DOE) Savannah River Site (SRS). The CSTF encompasses the F-Area and the H-Area Tank Farms including the Replacement High Level Waste Evaporator (RHLWE) (3H evaporator) as a segment of the H-Area Tank Farm. This EPHA is intended to identify and analyze those hazards that are significant enough to warrant consideration in the tank farm operational emergency management programs

Revision to flood hazard evaluation for the Savannah River Site

Energy Technology Data Exchange (ETDEWEB)

Buckley, R. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Werth, D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2014-08-25

Requirements for the Natural Phenomena Hazard (NPH) mitigation for new and existing Department of Energy (DOE) facilities are outlined in DOE Order 420.1. This report examines the hazards posed by potential flooding and represents an update to two previous reports. The facility-specific probabilistic flood hazard curve is defined as the water elevation for each annual probability of precipitation occurrence (or inversely, the return period in years). New design hyetographs for both 6-hr and 24-hr precipitation distributions were used in conjunction with hydrological models of various basins within the Savannah River Site (SRS). For numerous locations of interest, peak flow discharge and flood water elevation were determined. In all cases, the probability of flooding of these facilities for a 100,000 year precipitation event is negligible.

Glass Formulation and Fabrication Laboratory, Building 864, Hazards assessment document

Energy Technology Data Exchange (ETDEWEB)

Banda, Z.; Wood, C.L.

1995-08-01

The Department of Energy Order 5500.3A requires facility-specific hazards assessments be prepared, maintained, and used for emergency planning purposes. This hazards assessment document describes the chemical and radiological hazards associated with the Glass Formulation and Fabrication Laboratory, Building 864. The entire inventory was screened according to the potential airborne impact to onsite and offsite individuals. The air dispersion model, ALOHA, estimated pollutant concentrations downwind from the source of a release, taking into consideration the toxicological and physical characteristics of the release site, the atmospheric conditions, and the circumstances of the release. The greatest distances at which a postulated facility event will produce consequences exceeding the ERPG-2 threshold is 96 meters. The highest emergency classification is a Site Area Emergency. The Emergency Planning Zone is 100 meters.

Implementing robotics in the Department of Energy Dismantlement Program

International Nuclear Information System (INIS)

Jones, A.T.

1997-01-01

Since the end of the cold war, as our nuclear stockpile has decreased, the Department of Energy (DOE) has been working rapidly to safely dismantle weapons returned by the military. In order to be retired, weapons must be returned to the Pantex Plant in Amarillo, Texas. There they are reduced to their component parts. Although many of these parts are not hazardous, some, including certain explosive assemblies and radioactive materials, are sufficiently hazardous so that special handling systems are necessary. This paper will describe several of these systems developed by Sandia for Pantex and their technical basis

Preliminary Hazards Analysis Plasma Hearth Process

International Nuclear Information System (INIS)

Aycock, M.; Coordes, D.; Russell, J.; TenBrook, W.; Yimbo, P.

1993-11-01

This Preliminary Hazards Analysis (PHA) for the Plasma Hearth Process (PHP) follows the requirements of United States Department of Energy (DOE) Order 5480.23 (DOE, 1992a), DOE Order 5480.21 (DOE, 1991d), DOE Order 5480.22 (DOE, 1992c), DOE Order 5481.1B (DOE, 1986), and the guidance provided in DOE Standards DOE-STD-1027-92 (DOE, 1992b). Consideration is given to ft proposed regulations published as 10 CFR 830 (DOE, 1993) and DOE Safety Guide SG 830.110 (DOE, 1992b). The purpose of performing a PRA is to establish an initial hazard categorization for a DOE nuclear facility and to identify those processes and structures which may have an impact on or be important to safety. The PHA is typically performed during and provides input to project conceptual design. The PRA then is followed by a Preliminary Safety Analysis Report (PSAR) performed during Title I and II design. This PSAR then leads to performance of the Final Safety Analysis Report performed during construction, testing, and acceptance and completed before routine operation. Radiological assessments indicate that a PHP facility, depending on the radioactive material inventory, may be an exempt, Category 3, or Category 2 facility. The calculated impacts would result in no significant impact to offsite personnel or the environment. Hazardous material assessments indicate that a PHP facility will be a Low Hazard facility having no significant impacts either onsite or offsite to personnel and the environment

Dependent convergence: the importation of technological hazards by semiperipheral countries.

Science.gov (United States)

Siqueira, C E; Levenstein, C

2000-01-01

This article complements the substantial body of literature produced over the last three decades on the export of hazards from developed countries to developing countries. After reviewing the central arguments proposed by this literature, the authors add to the debate by focusing on the role of national actors in the importation of these hazards, based on the experience of late 1970s' developments in the petrochemical industry in Brazil. The Brazilian case indicates that social struggles and/or interactions among actors in developing and developed nations determine to what extent hazardous technologies are imported without environmental controls and to what extent their hazardous effects are controlled by these nations. This study suggests that the future development of a more inclusive theory of export-import of hazardous technologies and products should take into account the dialectical relationship established between social actors internal to the exporting and importing countries.

HACCP (Hazard Analysis Critical Control Points): is it coming to the dairy?

Science.gov (United States)

Cullor, J S

1997-12-01

The risks and consequences of foodborne and waterborne pathogens are coming to the forefront of public health concerns, and strong pressure is being applied on agriculture for immediate implementation of on-farm controls. The FDA is considering HACCP (Hazard Analysis Critical Control Points) as the new foundation for revision of the US Food Safety Assurance Program because HACCP is considered to be a science-based, systematic approach to the prevention of food safety problems. In addition, the implementation of HACCP principles permits more government oversight through requirements for standard operating procedures and additional systems for keeping records, places primary responsibility for ensuring food safety on the food manufacturer or distributor, and may assist US food companies in competing more effectively in the world market. With the HACCP-based program in place, a government investigator should be able to determine and evaluate both current and past conditions that are critical to ensuring the safety of the food produced by the facility. When this policy is brought to the production unit, the impact for producers and veterinarians will be substantial.

Superfund and Toxic Release Inventory Sites - INSTITUTIONAL_CONTROLS_IDEM_IN.SHP: Institutional Control Sites in Indiana (Indiana Department of Environmental Management, Polygon Shapefile)

Data.gov (United States)

NSGIC State | GIS Inventory — INSTITUTIONAL_CONTROLS_IDEM_IN is a polygon shapefile that contains Institutional Control (IC) site locations in Indiana, provided by personnel of Indiana Department...

An assessment of thermal destruction technologies for application to Department of Energy mixed wastes

International Nuclear Information System (INIS)

1991-08-01

As evidenced by the Department of Energy (DOE) Environmental Restoration and Waste Management Five-Year Plan, the Department is committing to a long-range waste management program. A category of waste that represents a sizable portion of the total DOE waste picture and also presents significant complications in management is waste that contains both hazardous and radioactive components. This category of wastes, referred to as mixed waste (MW), is present at all but a few of the Department's sites. The presence of radioactive constituents in this waste category implies that it be managed, like radioactive-only wastes, on DOE-owned property. Thermal treatment of MW's offers a variety of benefits in the final disposition of the waste. One obvious benefit is volume reduction of the waste if it contains organics because most of the organics are converted to gases and water, leaving only the inert material or ash. Another benefit is the destruction of hazardous materials by thermal conversion to simple, nonhazardous gases water. A third benefit, for some thermal technologies, is that the thermal process yields a process residue that meets disposal requirements for both hazardous and radioactive constituents without further processing. 2 refs., 47 figs., 8 tabs

Defense against terroristic hazards and risk by building planning law

International Nuclear Information System (INIS)

Hopkins, Richard

2012-01-01

The book on defense against terroristic hazards and risk by building planning law includes the following issues: Introduction: civil engineering and safety. Risk, hazards and urban planning: historical and actual examples for the constructional danger prevention, terroristic threat and urban planning. Risk, hazards and terrorism: sociology and risk, law and risk, terrorism - risk or hazard? Answer to uncertainty - risk prevention, catastrophe law as link. Risk, hazard, terrorism and the public building and regional planning law: regional planning law as point of origin, building law and terrorism, possibility of control by the legal building regulations.

Environmental Resources of Selected Areas of Hawaii: Geological Hazards (DRAFT)

Energy Technology Data Exchange (ETDEWEB)

Staub, W.P.

1994-06-01

This report has been prepared to make available and archive the background scientific data and related information collected on geologic hazards during the preparation of the environmental impact statement (EIS) for Phases 3 and 4 of the Hawaii Geothermal Project (HGP) as defined by the state of Hawaii in its April 1989 proposal to Congress. The U.S. Department of Energy (DOE) published a notice in the Federal Register on May 17, 1994 (Fed Regis. 5925638) withdrawing its Notice of Intent (Fed Regis. 575433) of February 14, 1992, to prepare the HGP-EIS. Since the state of Hawaii is no longer pursuing or planning to pursue the HGP, DOE considers the project to be terminated This report presents a review of current information on geologic hazards in the Hawaiian Islands. Interrelationships among these hazards are discussed. Probabilities of occurrence of given geologic hazards are provided in various regions where sufficient geologic or historical data are available. Most of the information contained herein is compiled from recent U.S. Geological Survey (USGS) publications and open-file reports. This report describes the natural geologic hazards present in the area and does not represent an assessment of environmental impacts. Geologic hazards originate both onshore and offshore. Onshore geologic hazards such as volcanic eruptions, earthquakes, surface rupture, landslides, uplift, and subsidence occur mainly on the southern third of the island of Hawaii (hereinafter referred to as Hawaii). Offshore geologic hazards are more widely distributed throughout the Hawaiian Islands. Examples of offshore geologic hazards are submarine landslides, turbidity currents, and seismic sea waves (tsunamis). First, overviews of volcanic and earthquake activity, and details of offshore geologic hazards is provided for the Hawaiian Islands. Then, a more detailed discussion of onshore geologic hazards is presented with special emphasis on the southern third of Hawaii and the east rift

Hanford Site Hazardous waste determination report for transuranic debris waste streams NPFPDL2A

International Nuclear Information System (INIS)

WINTERHALDER, J.A.

1999-01-01

This hazardous waste determination report (Report) describes the process and information used on the Hanford Site to determine that waste stream number NPFPDLZA, consisting of 30 containers of contact-handled transuranic debris waste, is not hazardous waste regulated by the Resource Conservation and Recovery Act (RCRA) or the New Mexico Hazardous Waste Act. For a waste to be hazardous under these statutes, the waste either must be specifically listed as a hazardous waste, or exhibit one or more of the characteristics of a hazardous waste, Le., ignitability, corrosivity, reactivity, or toxicity. Waste stream NPFPDLZA was generated, packaged, and placed into storage between 1993 and 1997. Extensive knowledge of the waste generating process, facility operational history, and administrative controls and operating procedures in effect at the time of generation, supported the initial nonhazardous waste determination. Because of the extent and reliability of information pertaining to this waste type, and the total volume of waste in the debris matrix parameter category, the Hanford Site is focusing initial efforts on this and similar waste streams for the first shipment to the Waste Isolation Pilot Plant (WIPP). RCRA regulations authorize hazardous waste determinations to be made either by using approved sampling and analysis methods or by applying knowledge of the waste in light of the materials or the process(es) used. This latter approach typically is referred to as process knowledge. The Transuranic Waste Characterization Quality Assurance Program Plan (CAO-94-1010) for WIPP refers to acceptable knowledge in essentially the same terms; acceptable knowledge as used throughout this Report is synonymous with the term process knowledge. The 30 containers addressed in this Report were characterized by the following methods: Acceptable knowledge; Nondestructive examination using real-time radiography; Visual examination; and Headspace gas sampling and analysis. The initial

Hanford Site Hazardous waste determination report for transuranic debris waste streams NPFPDL2A

Energy Technology Data Exchange (ETDEWEB)

WINTERHALDER, J.A.

1999-09-29

This hazardous waste determination report (Report) describes the process and information used on the Hanford Site to determine that waste stream number NPFPDLZA, consisting of 30 containers of contact-handled transuranic debris waste, is not hazardous waste regulated by the Resource Conservation and Recovery Act (RCRA) or the New Mexico Hazardous Waste Act. For a waste to be hazardous under these statutes, the waste either must be specifically listed as a hazardous waste, or exhibit one or more of the characteristics of a hazardous waste, Le., ignitability, corrosivity, reactivity, or toxicity. Waste stream NPFPDLZA was generated, packaged, and placed into storage between 1993 and 1997. Extensive knowledge of the waste generating process, facility operational history, and administrative controls and operating procedures in effect at the time of generation, supported the initial nonhazardous waste determination. Because of the extent and reliability of information pertaining to this waste type, and the total volume of waste in the debris matrix parameter category, the Hanford Site is focusing initial efforts on this and similar waste streams for the first shipment to the Waste Isolation Pilot Plant (WIPP). RCRA regulations authorize hazardous waste determinations to be made either by using approved sampling and analysis methods or by applying knowledge of the waste in light of the materials or the process(es) used. This latter approach typically is referred to as process knowledge. The Transuranic Waste Characterization Quality Assurance Program Plan (CAO-94-1010) for WIPP refers to acceptable knowledge in essentially the same terms; acceptable knowledge as used throughout this Report is synonymous with the term process knowledge. The 30 containers addressed in this Report were characterized by the following methods: Acceptable knowledge; Nondestructive examination using real-time radiography; Visual examination; and Headspace gas sampling and analysis. The initial

Fire hazard analysis for the K basin fuel transfer system anneses project A-15

International Nuclear Information System (INIS)

BARILO, N.F.

2001-01-01

The purpose of the Fuel Transfer System (FTS) is to move the spent nuclear fuel currently stored in the K East (KE) Basin and transfer it by shielded cask to the K West (KW) Basin. The fuel will then be processed through the existing fuel cleaning and loading system prior to being loaded into Multi-Canister Overpacks (MCO). The FTS operation is considered an intra-facility transfer because the spent fuel will stay within the 100 K area and between the K Basins. This preliminary Fire Hazards Analysis (FHA) for the K Basin FTS Annexes addresses fire hazards or fire-related concerns in accordance with U.S. Department of Energy (DOE) 420.1 (DOE 2000), and RLID 420.1 (DOE 1999), resulting from or related to the processes and equipment. It is intended to assess the risk from fire associated within the FTS Annexes to ensure that there are no undue fire hazards to site personnel and the public; the potential for the occurrence of a fire is minimized; process control and safety systems are not damaged by fire or related perils; and property damage from fire and related perils does not exceed an acceptable level. Consistent with the preliminary nature of the design information, this FHA is performed on a graded approach

Hazard interactions and interaction networks (cascades) within multi-hazard methodologies

Science.gov (United States)

Gill, Joel C.; Malamud, Bruce D.

2016-08-01

This paper combines research and commentary to reinforce the importance of integrating hazard interactions and interaction networks (cascades) into multi-hazard methodologies. We present a synthesis of the differences between multi-layer single-hazard approaches and multi-hazard approaches that integrate such interactions. This synthesis suggests that ignoring interactions between important environmental and anthropogenic processes could distort management priorities, increase vulnerability to other spatially relevant hazards or underestimate disaster risk. In this paper we proceed to present an enhanced multi-hazard framework through the following steps: (i) description and definition of three groups (natural hazards, anthropogenic processes and technological hazards/disasters) as relevant components of a multi-hazard environment, (ii) outlining of three types of interaction relationship (triggering, increased probability, and catalysis/impedance), and (iii) assessment of the importance of networks of interactions (cascades) through case study examples (based on the literature, field observations and semi-structured interviews). We further propose two visualisation frameworks to represent these networks of interactions: hazard interaction matrices and hazard/process flow diagrams. Our approach reinforces the importance of integrating interactions between different aspects of the Earth system, together with human activity, into enhanced multi-hazard methodologies. Multi-hazard approaches support the holistic assessment of hazard potential and consequently disaster risk. We conclude by describing three ways by which understanding networks of interactions contributes to the theoretical and practical understanding of hazards, disaster risk reduction and Earth system management. Understanding interactions and interaction networks helps us to better (i) model the observed reality of disaster events, (ii) constrain potential changes in physical and social vulnerability

Intentional and unintentional poisoning in Pakistan: a pilot study using the Emergency Departments surveillance project.

Science.gov (United States)

Khan, Nadeem; Pérez-Núñez, Ricardo; Shamim, Nudrat; Khan, Uzma; Naseer, Naureen; Feroze, Asher; Razzak, Junaid; Hyder, Adnan A

2015-01-01

Acute poisoning is one of the most common reasons for emergency department visits around the world. In Pakistan, the epidemiological data on poisoning is limited due to an under developed poison information surveillance system. We aim to describe the characteristics associated with intentional and unintentional poisoning in Pakistan presenting to emergency departments. The data was extracted from the Pakistan National Emergency Department Surveillance (Pak-NEDS) which was an active surveillance conducted between November 2010 and March 2011. All patients, regardless of age, who presented with poisoning to any of Pakistan's seven major tertiary care centers' emergency departments, were included. Information about patient demographics, type of poisoning agent, reason for poisoning and outcomes were collected using a standard questionnaire. Acute poisoning contributed to 1.2% (n = 233) of patients with intentional and unintentional injuries presenting to EDs of participating centers. Of these, 68% were male, 54% were aged 19 to 44 and 19% were children and adolescents (<18 years). Types of poisoning included chemical/gas (43.8%), drug/medicine (27%), alcohol (16.7%) and food/plant (6%). In half of all patients the poisoning was intentional. A total of 11.6% of the patients were admitted and 6.6% died. Poisoning causes more morbidity and mortality in young adults in Pakistan compared to other age groups, half of which is intentional. Improving mental health, regulatory control for hazardous chemicals and better access to care through poison information centers and emergency departments will potentially help control the problem.

Fire Protection Program fiscal year 1996, site support program plan Hanford Fire Department. Revision 2

International Nuclear Information System (INIS)

Good, D.E.

1995-09-01

The mission of the Hanford Fire Department (HFD) is to support the safe and timely cleanup of the Hanford site by providing fire suppression, fire prevention, emergency rescue, emergency medical service, and hazardous materials response; and to be capable of dealing with and terminating emergency situations which could threaten the operations, employees, or interest of the US Department of Energy operated Hanford Site. This includes response to surrounding fire departments/districts under a mutual aid agreement and contractual fire fighting, hazardous materials, and ambulance support to Washington Public Power Supply System (Supply System). The fire department also provides site fire marshal overview authority, fire system testing and maintenance, self-contained breathing apparatus maintenance, building tours and inspections, ignitable and reactive waste site inspections, prefire planning, and employee fire prevention education. This report gives a program overview, technical program baselines, and cost and schedule baseline

Potential hazards in smoke-flavored fish

Science.gov (United States)

Lin, Hong; Jiang, Jie; Li, Donghua

2008-08-01

Smoking is widely used in fish processing for the color and flavor. Smoke flavorings have evolved as a successful alternative to traditional smoking. The hazards of the fish products treated by liquid-smoking process are discussed in this review. The smoke flavoring is one important ingredient in the smoke-flavored fish. This paper gives the definition of smoke flavorings and the hazard of polycyclic aromatic hydrocarbons (PAHs) residue in the smoke flavorings on the market. It gives also an assessment of chemical hazards such as carcinogenic PAHs, especially Benzo-[ a]pyrene, as well as biological hazards such as Listeria monocytogenes, Clostridium botulinum, histamine and parasites in smoke-flavored fish. The limitations in regulations or standards are discussed. Smoke flavored fish have lower content of PAHs as compared with the traditional smoking techniques if the PAHs residue in smoke flavorings is controlled by regulations or standards.

Hazardous Materials Management and Emergency Response training Center needs assessment

International Nuclear Information System (INIS)

McGinnis, K.A.; Bolton, P.A.; Robinson, R.K.

1993-09-01

For the Hanford Site to provide high-quality training using simulated job-site situations to prepare the 4,000 Site workers and 500 emergency responders for known and unknown hazards a Hazardous Materials Management and Emergency Response Training Center is needed. The center will focus on providing classroom lecture as well as hands-on, realistic training. The establishment of the center will create a partnership among the US Department of Energy; its contractors; labor; local, state, and tribal governments; and Xavier and Tulane Universities of Louisiana. This report presents the background, history, need, benefits, and associated costs of the proposed center

Impacts of hazardous waste regulation on low-level waste management

International Nuclear Information System (INIS)

Sharples, F.E.; Eyman, L.D.

1987-01-01

Since passage of the 1984 amendments to the Resource Conservation and Recovery Act (RCRA), major changes have occurred in the regulation of hazardous waste. The US Environmental Protection Agency (EPA) has also greatly modified its interpretation of how these regulations apply to wastes from federal facilities, including defense wastes from US Department of Energy (DOE) sites. As a result, the regulatory distinctions between low-level radioactive waste (LLW) and hazardous waste are becoming blurred. This paper discusses recent statutory and regulatory changes and how they might affect the management of LLW at DOE facilities. 6 references

Hazardous Waste Development, Demonstration, and Disposal (HAZWDDD) program plan: Executive summary

International Nuclear Information System (INIS)

McGinnis, C.P.; Eisenhower, B.M.; Reeves, M.E.; DePaoli, S.M.; Stinton, L.H.; Harrington, E.H.

1989-02-01

The Hazardous Waste Development, Demonstration, and Disposal (HAZWDDD) Program Plan provides a strategy for management of hazardous and mixed wastes generated by the five Department of Energy (DOE) installations managed by Martin Marietta Energy Systems, Inc. (Energy Systems). This integrated corporate plan is based on the individual installation plans, which identify waste streams, facility capabilities, problem wastes, future needs, and funding needs. Using this information, the corporate plan identifies common concerns and technology/facility needs over the next 10 years. The overall objective of this corporate plan is to ensure that treatment, storage, and disposal (TSD) needs for all hazardous and mixed wastes generated by Energy Systems installations have been identified and planned for. Specific objectives of the program plan are to (1) identify all hazardous and mixed waste streams; (2) identify hazardous and mixed waste TSD requirements; (3) identify any unresolved technical issues preventing implementation of the strategy; (4) develop schedules for studies, demonstrations, and facilities to resolve the issues; and (5) define the interfaces with the Low-Level Waste Disposal Development and Demonstration (LLWDDD) Program. 10 refs., 7 figs

Efficacy of Acute Pain Control Protocol in Triage Department on Analgesics Administration Time and Patients' Satisfaction

Directory of Open Access Journals (Sweden)

Seyedhossein Seyyedhoseini Davaraani

2014-07-01

Full Text Available Objective: Current study was conducted to develop a pain control protocol by Morphine Sulfate (MS Suppository in triage ward with the main primary outcomes of first analgesic administration time, patients' satisfaction and also the changes in pain intensity. Methods: In this randomized clinical trial, 318 consecutive patients attending to an academic tertiary health care center in Tehran, Iran in 2011 and 2012 were enrolled. The patients were randomly assigned to receive either routine pain control by emergency medicine residents in emergency department (n=132 or pain control protocol in triage level by nurses (n=186. Those with pain in control group were treated with conventional pain control program and those in intervention group with pain intensities higher than four were treated with suppository stat 10 mg dose of MS administered by nurses in triage ward. Results: The mean change in pain intensity was significantly (P<0.0001 higher in intervention group (4.2 versus 0.2 and the first analgesic administration time was significantly different between groups (P<0.05 being less in the intervention group (43.1 versus 4.6. Also the patients' satisfaction was significantly higher in the intervention group (P<0.0001. No drug adverse effects were seen. Conclusions: Totally, according to the obtained results, it may be concluded that acute pain control protocol in triage department by suppository of MS would result in reduced analgesics administration time and higher patients' satisfaction.   Keywords: Analgesia; Emergency Department; Pain Control

Perceptions of hazard and risk on Santorini

Science.gov (United States)

Dominey-Howes, Dale; Minos-Minopoulos, Despina

2004-10-01

Santorini, Greece is a major explosive volcano. The Santorini volcanic complex is composed of two active volcanoes—Nea Kameni and Mt. Columbo. Holocene eruptions have generated a variety of processes and deposits and eruption mechanisms pose significant hazards of various types. It has been recognized that, for major European volcanoes, few studies have focused on the social aspects of volcanic activity and little work has been conducted on public perceptions of hazard, risk and vulnerability. Such assessments are an important element of establishing public education programmes and developing volcano disaster management plans. We investigate perceptions of volcanic hazards on Santorini. We find that most residents know that Nea Kameni is active, but only 60% know that Mt. Columbo is active. Forty percent of residents fear that negative impacts on tourism will have the greatest effect on their community. In the event of an eruption, 43% of residents would try to evacuate the island by plane/ferry. Residents aged >50 have retained a memory of the effects of the last eruption at the island, whereas younger residents have no such knowledge. We find that dignitaries and municipal officers (those responsible for planning and managing disaster response) are informed about the history, hazards and effects of the volcanoes. However, there is no "emergency plan" for the island and there is confusion between various departments (Civil Defense, Fire, Police, etc.) about the emergency decision-making process. The resident population of Santorini is at high risk from the hazards associated with a future eruption.

Second DOE natural phenomena hazards mitigation conference

International Nuclear Information System (INIS)

1989-01-01

This conference has been organized into ten presentation sessions which include an overview of the DOE Natural Phenomena Guidelines, Seismic Analysis, Seismic Design, Modifying Existing Facilities, DOE Orders, Codes, and Standards (2 sessions), Seismic Hazard (2 sessions), and Probabilistic Risk Assessment (2 sessions). Two poster sessions were also included in the program to provide a different forum for communication of ideas. Over the past fourteen years, Lawrence Livermore National Laboratory, Nuclear Systems Safety Program, has been working with the US Department of Energy, Office of Safety Appraisals and their predecessors in the area of natural phenomena hazards. During this time we have developed seismic, extreme wind/tornado, and flood hazard models for DOE sites in the United States. Guidelines for designing and evaluating DOE facilities for natural phenomena have been developed and are in interim use throughout the DOE community. A series of state-of-the practice manuals have also been developed to aid the designers. All of this material is listed in the Natural Phenomena Hazards Bibliography included in these proceedings. This conference provides a mechanism to disseminate current information on natural phenomena hazards and their mitigation. It provides an opportunity to bring together members of the DOE community to discuss current projects, to share information, and to hear practicing members of the structural engineering community discuss their experiences from past natural phenomena, future trends, and any changes to building codes. Each paper or poster presented is included in these proceedings. We have also included material related to the luncheon and dinner talks

Hazard, sensorial and economic analysis critical control point (HACCP) check list for radiation sterilized ready-to-eat meals

Energy Technology Data Exchange (ETDEWEB)

Haruvy, Y F [Soreq Nuclear Research Centre, Operations Division, QA Department, Yavne (Israel)

2004-07-01

The primary objective of this work is to introduce a modified HACCP analysis route, for irradiated prepared meals that addresses not only health hazards but also sensorial failures, economic risks. Above all, this method aims at pinpointing failure modes specific to the radiation pasteurization aspect of the production and the product. The suggested modified analysis should serve all researchers in the CRP in their attempts to transfer their process and product from the laboratory-research type into an industrial one. While in the laboratory we can discard 'failure' samples or lots, or parts of a lot that are of inferior quality, an industrial process must be profitable and, hence, stable and reproducibly producing high quality products. The basic aspects of the HACCP route are: HACCP describes a system of control for assuring food safety and provides a more structured and critical approach to the control of identified hazards than that achievable by traditional inspection and quality control procedures; It has the potential to identify areas of concern where failure has not yet been experienced, making it particularly useful for new operations. The analysis route is exemplified in tables, that cover all the steps involved in the food production, from farm to fork.

Hazard analysis and critical control point to irradiated food in Brazil

International Nuclear Information System (INIS)

Boaratti, Maria de Fatima Guerra

2004-01-01

Food borne diseases, in particular gastro-intestinal infections, represent a very large group of pathologies with a strong negative impact on the health of the population because of their widespread nature. Little consideration is given to such conditions due to the fact that their symptoms are often moderate and self-limiting. This has led to a general underestimation of their importance, and consequently to incorrect practices during the preparation and preservation of food, resulting in the frequent occurrence of outbreaks involving groups of varying numbers of consumers. Despite substantial efforts in the avoidance of contamination, an upward trend in the number of outbreaks of food borne illnesses caused by non-spore forming pathogenic bacteria are reported in many countries. Good hygienic practices can reduce the level of contamination but the most important pathogens cannot presently be eliminated from most farms, nor is it possible to eliminate them by primary processing, particularly from those foods which are sold raw. Several decontamination methods exist but the most versatile treatment among them is the ionizing radiation procedure. HACCP (Hazard Analysis and Critical Control Point) is a management system in which food safety is addressed through the analysis and control of biological, chemical, and physical hazards from raw material production, procurement and handling, to manufacturing, distribution and consumption of the finished product. For successful implementation of a HACCP plan, management must be strongly committed to the HACCP concept. A firm commitment to HACCP by top management provides company employees with a sense of the importance of producing safe food. At the same time, it has to be always emphasized that, like other intervention strategies, irradiation must be applied as part of a total sanitation program. The benefits of irradiation should never be considered as an excuse for poor quality or for poor handling and storage conditions

Approach-avoidance pattern of visual attention in hazardous drinkers with ambivalence.

Science.gov (United States)

Lee, Saerom; Cho, Sungkun; Lee, Jang-Han

2014-03-01

Ambivalence toward alcohol often develops when hazardous drinkers try to quit or to control their drinking. The purpose of this study was to investigate the differences between hazardous drinkers with and without ambivalence toward alcohol in terms of their visual attention to alcohol-related pictures over time using an eye-tracker. The study included 20 hazardous drinkers with ambivalence and 21 hazardous drinkers without ambivalence. The eye movements of the participants were monitored while the participants conducted a free-viewing task in which 20 pairs of alcohol-related pictures and matched control pictures were presented. The results showed that the hazardous drinkers with ambivalence were more attentive to the alcohol-related pictures at first and were more attentive to the control pictures toward the end of the task. On the other hand, the hazardous drinkers without ambivalence were more attentive to the alcohol-related pictures from beginning to end. The findings of this study indicated that ambivalence toward alcohol resulted in the inclination to approach and then avoid alcohol in a consecutive sequence. The present results could be helpful in distinguishing hazardous drinkers who may have ambivalence toward alcohol and identifying the pattern of ambivalence more concretely. Additionally, further studies need to consider the time that is important to measure ambivalence toward alcohol. Copyright © 2013 Elsevier Ltd. All rights reserved.

WIPP's Hazardous Waste Facility Permit Renewal Application

International Nuclear Information System (INIS)

Most, W.A.; Kehrman, R.F.

2009-01-01

Hazardous waste permits issued by the New Mexico Environment Department (NMED) have a maximum term of 10-years from the permit's effective date. The permit condition in the Waste Isolation Pilot Plant's (WIPP) Hazardous Waste Facility Permit (HWFP) governing renewal applications, directs the Permittees to submit a permit application 180 days prior to expiration of the Permit. On October 27, 1999, the Secretary of the NMED issued to the United States Department of Energy (DOE), the owner and operator of WIPP, and to Washington TRU Solutions LLC (WTS), the Management and Operating Contractor and the cooperator of WIPP, a HWFP to manage, store, and dispose hazardous waste at WIPP. The DOE and WTS are collectively known as the Permittees. The HWFP is effective for a fixed term not to exceed ten years from the effective date of the Permit. The Permittees may renew the HWFP by submitting a new permit application at least 180 calendar days before the expiration date, of the HWFP. The Permittees are not proposing any substantial changes in the Renewal Application. First, the Permittees are seeking the authority to dispose of Contact-Handled and Remote-Handled TRU mixed waste in Panel 8. Panels 4 through 7 have been approved in the WIPP Hazardous Waste Facility Permit as it currently exists. No other change to the facility or to the manner in which hazardous waste is characterized, managed, stored, or disposed is being requested. Second, the Permittees also seek to include the Mine Ventilation Rate Monitoring Plan, as Attachment Q in the HWFP. This Plan has existed as a separate document since May 2000. The NMED has requested that the Plan be submitted as part of the Renewal Application. The Permittees have been operating to the Mine Ventilation Rate Monitoring Plan since the Plan was submitted. Third, some information submitted in the original WIPP RCRA Part B Application has been updated, such as demographic information. The Permittees will submit this information in the

Hazard Analysis of Software Requirements Specification for Process Module of FPGA-based Controllers in NPP

Energy Technology Data Exchange (ETDEWEB)

Jung; Sejin; Kim, Eui-Sub; Yoo, Junbeom [Konkuk University, Seoul (Korea, Republic of); Keum, Jong Yong; Lee, Jang-Soo [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-10-15

Software in PLC, FPGA which are used to develop I and C system also should be analyzed to hazards and risks before used. NUREG/CR-6430 proposes the method for performing software hazard analysis. It suggests analysis technique for software affected hazards and it reveals that software hazard analysis should be performed with the aspects of software life cycle such as requirements analysis, design, detailed design, implements. It also provides the guide phrases for applying software hazard analysis. HAZOP (Hazard and operability analysis) is one of the analysis technique which is introduced in NUREG/CR-6430 and it is useful technique to use guide phrases. HAZOP is sometimes used to analyze the safety of software. Analysis method of NUREG/CR-6430 had been used in Korea nuclear power plant software for PLC development. Appropriate guide phrases and analysis process are selected to apply efficiently and NUREG/CR-6430 provides applicable methods for software hazard analysis is identified in these researches. We perform software hazard analysis of FPGA software requirements specification with two approaches which are NUREG/CR-6430 and HAZOP with using general GW. We also perform the comparative analysis with them. NUREG/CR-6430 approach has several pros and cons comparing with the HAZOP with general guide words and approach. It is enough applicable to analyze the software requirements specification of FPGA.

Princeton Plasma Physics Laboratory (PPPL) seismic hazard analysis

International Nuclear Information System (INIS)

Savy, J.

1989-01-01

New design and evaluation guidelines for department of energy facilities subjected to natural phenomena hazard, are being finalized. Although still in draft form at this time, the document describing those guidelines should be considered to be an update of previously available guidelines. The recommendations in the guidelines document mentioned above, and simply referred to as the ''guidelines'' thereafter, are based on the best information at the time of its development. In particular, the seismic hazard model for the Princeton site was based on a study performed in 1981 for Lawrence Livermore National Laboratory (LLNL), which relied heavily on the results of the NRC's Systematic Evaluation Program and was based on a methodology and data sets developed in 1977 and 1978. Considerable advances have been made in the last ten years in the domain of seismic hazard modeling. Thus, it is recommended to update the estimate of the seismic hazard at the DOE sites whenever possible. The major differences between previous estimates and the ones proposed in this study for the PPPL are in the modeling of the strong ground motion at the site, and the treatment of the total uncertainty in the estimates to include knowledge uncertainty, random uncertainty, and expert opinion diversity as well. 28 refs

Princeton Plasma Physics Laboratory (PPPL) seismic hazard analysis

Energy Technology Data Exchange (ETDEWEB)

Savy, J.

1989-10-01

New design and evaluation guidelines for department of energy facilities subjected to natural phenomena hazard, are being finalized. Although still in draft form at this time, the document describing those guidelines should be considered to be an update of previously available guidelines. The recommendations in the guidelines document mentioned above, and simply referred to as the guidelines'' thereafter, are based on the best information at the time of its development. In particular, the seismic hazard model for the Princeton site was based on a study performed in 1981 for Lawrence Livermore National Laboratory (LLNL), which relied heavily on the results of the NRC's Systematic Evaluation Program and was based on a methodology and data sets developed in 1977 and 1978. Considerable advances have been made in the last ten years in the domain of seismic hazard modeling. Thus, it is recommended to update the estimate of the seismic hazard at the DOE sites whenever possible. The major differences between previous estimates and the ones proposed in this study for the PPPL are in the modeling of the strong ground motion at the site, and the treatment of the total uncertainty in the estimates to include knowledge uncertainty, random uncertainty, and expert opinion diversity as well. 28 refs.

Potential hazards and risks associated with the aquaculture industry ...

African Journals Online (AJOL)

Aquaculture, the farming of aquatic organisms, is fraught with potential hazards and risks which are categorized into occupational, environmental, food safety and public health. This paper reviewed major hazards and risks associated with the aquaculture industry and proffered strategies for their management and control.

A comprehensive review of the implementation of hazard analysis critical control point (HACCP) to the production of flour and flour-based products.

Science.gov (United States)

Arvanitoyannis, Ioannis S; Traikou, Athina

2005-01-01

The production of flour and semolina and their ensuing products, such as bread, cake, spaghetti, noodles, and corn flakes, is of major importance, because these products constitute some of the main ingredients of the human diet. The Hazard Analysis Critical Control Point (HACCP) system aims at ensuring the safety of these products. HACCP has been implemented within the frame of this study on various products of both Asian and European origin; the hazards, critical control limits (CCLs), observation practices, and corrective actions have been summarized in comprehensive tables. Furthermore, the various production steps, packaging included, were thoroughly analyzed, and reference was made to both the traditional and new methodologies in an attempt to pinpoint the occurring differences (advantages and disadvantages) per process.

Application of HACCP principles as a management tool for monitoring and controlling microbiological hazards in water treatment facilities.

Science.gov (United States)

Jagals, C; Jagals, P

2004-01-01

HACCP (hazard analysis and critical control points) principles were applied to evaluate the effectiveness of two water treatment facilities to continually produce potable water free of microbiological health hazards. This paper reports a hazard analyses protocol (microbiological hazards based on faecal coliforms (FC) and turbidity (TBY) as indicators) for critical control points (CCPs) within each facility. The CCPs were raw resource water, sedimentation, filtration and chlorine-disinfection. The aim was to determine the effectiveness of each CCP to remove the indicators from the water under treatment. Arbitrary critical performance limit targets (CPLTs) were set up for each CCP to determine to what extent each contributed to effective removal and to predict what the effect would be if any of the CCPs should fail. Health-related water quality guideline limits for expected health effects were applied and compliance measured at the 90th percentile. The raw resource river water used at both treatment facilities complied with raw resource water extraction CPLTs. The treated potable water complied with health-related drinking water guidelines. Sedimentation removed the largest proportion of the indicators from the raw water, but showed failure potential that could overload the consequent system. Filtration effectiveness at both treatment facilities showed potential to break down the overall effectiveness of the entire treatment facility, since the filter systems failed to meet their respective CPLTs. This left the disinfection phase to remove the remaining portion of indicators. Faecal coliforms appeared to be completely removed from post-chlorination samples. This indicated that both chlorine disinfection phases were 100% effective in meeting their disinfection CPLTs, despite having to "clean up" the indicator organisms that spilt over from the upstream CCPs. This, nevertheless, implied a risk of unsafe water release into distribution. CCPs at these treatment

Ranking system for mixed radioactive and hazardous waste sites

International Nuclear Information System (INIS)

Hawley, K.A.; Napier, B.A.

1985-01-01

The Environmental Protection Agency's Hazard Ranking System (HRS) is a simplified management decision tool that provides a common basis for evaluating a multitude of hazardous waste sites. A deficiency in the HRS for application to Department of Energy mixed radioactive and hazardous waste sites is its inability to explicitly handle radioactive material. A modification to the basic HRS to add the capability to consider radioactivity is described. The HRS considers the exposure routes of direct contact, fire/explosion, atmospheric release, surface-water release, and ground-water release. Each exposure route is further divided into release, route, containment, waste, and target characteristics. To maintain the basic HRS structure, only the waste characteristics section of each exposure route was modified. A ranking system was developed, using radiation dose pathway analysis, to group radionuclides by dose factors. For mixed waste sites, the ranking factor derived for radionuclides is compared with the ranking factor obtained for hazardous chemicals and the most restrictive is used in the overall ranking. The modified HRS has the advantages of being compatible with the original HRS, has reasonable information requirements, and provides scientifically defensible conclusions. 17 references, 2 figures, 6 tables

A Performance Management Initiative for Local Health Department Vector Control Programs.

Science.gov (United States)

Gerding, Justin; Kirshy, Micaela; Moran, John W; Bialek, Ron; Lamers, Vanessa; Sarisky, John

2016-01-01

Local health department (LHD) vector control programs have experienced reductions in funding and capacity. Acknowledging this situation and its potential effect on the ability to respond to vector-borne diseases, the U.S. Centers for Disease Control and Prevention and the Public Health Foundation partnered on a performance management initiative for LHD vector control programs. The initiative involved 14 programs that conducted a performance assessment using the Environmental Public Health Performance Standards. The programs, assisted by quality improvement (QI) experts, used the assessment results to prioritize improvement areas that were addressed with QI projects intended to increase effectiveness and efficiency in the delivery of services such as responding to mosquito complaints and educating the public about vector-borne disease prevention. This article describes the initiative as a process LHD vector control programs may adapt to meet their performance management needs. This study also reviews aggregate performance assessment results and QI projects, which may reveal common aspects of LHD vector control program performance and priority improvement areas. LHD vector control programs interested in performance assessment and improvement may benefit from engaging in an approach similar to this performance management initiative.

Potential biological hazard of importance for HACCP plans in fresh fish processing

Directory of Open Access Journals (Sweden)

Baltić Milan Ž.

2009-01-01

Full Text Available The Hazard Analysis and Critical Control Point (HACCP system is scientifically based and focused on problem prevention in order to assure the produced food products are safe to consume. Prerequisite programs such as GMP (Good Manufacturing Practices, GHP (Good Hygienic Practices are an essential foundation for the development and implementation of successful HACCP plans. One of the preliminary tasks in the development of HACCP plan is to conduct a hazard analysis. The process of conducting a hazard analysis involves two stages. The first is hazard identification and the second stage is the HACCP team decision which potential hazards must be addressed in the HACCP plan. By definition, the HACCP concept covers all types of potential food safety hazards: biological, chemical and physical, whether they are naturally occurring in the food, contributed by the environment or generated by a mistake in the manufacturing process. In raw fish processing, potential significant biological hazards which are reasonably likely to cause illness of humans are parasites (Trematodae, Nematodae, Cestodae, bacteria (Salmonella, E. coli, Vibrio parahemolyticus, Vibrio vulnificus, Listeria monocytogenes, Clostridium botulinum, Staphyloccocus aureus, viruses (Norwalk virus, Entero virusesi, Hepatitis A, Rotovirus and bio-toxins. Upon completion of hazard analysis, any measure(s that are used to control the hazard(s should be described.

Financial assistance to States and tribes to support emergency preparedness and response and the safe transportation of hazardous shipments

International Nuclear Information System (INIS)

Bradbury, J.A.; Jones, M.L.

1995-01-01

This report identifies and summarizes existing sources of financial assistance to States and Indian tribes in preparing and responding to transportation emergencies and ensuring the safe transportation of hazardous shipments through their jurisdictions. The report has been prepared as an information resource for the US Department of Energy's Office of Environmental Restoration and Waste Management, Office of Transportation, Emergency Management and Analytical Services. The report discusses funding programs administered by the following Federal agencies: Federal Emergency Management Agency; Department of Transportation; the Environmental Protection Agency; and the Department of Energy. Also included is a summary of fees assessed by some States on carriers of hazardous materials and hazardous waste. The discussion of programs is supplemented by an Appendix that provides a series of tables summarizing funding sources and amounts. The report includes several conclusions concerning the level of funding provided to Indian tribes, the relative ranking of funding sources and the variation among States in overall revenues for emergency response and safe transportation

Reducing hazardous cleaning product use: a collaborative effort.

Science.gov (United States)

Pechter, Elise; Azaroff, Lenore S; López, Isabel; Goldstein-Gelb, Marcy

2009-01-01

Workplace hazards affecting vulnerable populations of low-wage and immigrant workers present a special challenge to the practice of occupational health. Unions, Coalition for Occupational Safety and Health (COSH) groups, and other organizations have developed worker-led approaches to promoting safety. Public health practitioners can provide support for these efforts. This article describes a successful multiyear project led by immigrant cleaning workers with their union, the Service Employees International Union (SEIU) Local 615, and with support from the Massachusetts COSH (MassCOSH) to address exposure to hazardous chemicals. After the union had identified key issues and built a strategy, the union and MassCOSH invited staff from the Massachusetts Department of Public Health's Occupational Health Surveillance Program (OHSP) to provide technical information about health effects and preventive measures. Results included eliminating the most hazardous chemicals, reducing the number of products used, banning mixing products, and improving safety training. OHSP's history of public health practice regarding cleaning products enabled staff to respond promptly. MassCOSH's staff expertise and commitment to immigrant workers allowed it to play a vital role.

Risk management of onsite transportation of hazardous materials

International Nuclear Information System (INIS)

Wang, O.S.; Field, J.G.

1992-10-01

The US Department of Energy's (DOE) Hanford Site has recently undergone a significant change in its mission. The focus of site-wide operations has been shifted from production to environmental restoration. As a result, there is a significant increase in quantities of the radioactive wastes and other hazardous materials to be packaged and transported onsite. In response to the elevated transportation activities, the operations and engineering contractor for the Hanford Site, Westinghouse Hanford Company (Westinghouse Hanford), is proposing an integrated risk assessment methodology and risk management strategy to further enhance the safe operations of the onsite packaging and transportation activities involving radioactive and other hazardous materials. This paper summarizes Westinghouse Hanford's proposed risk assessment and risk management methodology for onsite transportation of hazardous materials. The proposed Westinghouse Hanford risk assessment and management methodology for onsite packaging and transportation has three integral parts: risk assessment, risk acceptance criteria, and risk minimization process. The purposes are to ensure that the risk for each ongoing transportation activity is acceptable, and to further reduce the overall risk for current and future onsite transportation activities

Hazardous Materials Pharmacies - A Vital Component of a Robust P2 Program

International Nuclear Information System (INIS)

McCarter, S.

2006-01-01

Integrating pollution prevention (P2) into the Department of Energy Integrated Safety Management (ISM) - Environmental Management System (EMS) approach, required by DOE Order 450.1, leads to an enhanced ISM program at large and complex installations and facilities. One of the building blocks to integrating P2 into a comprehensive environmental and safety program is the control and tracking of the amounts, types, and flow of hazardous materials used on a facility. Hazardous materials pharmacies (typically called HazMarts) provide a solid approach to resolving this issue through business practice changes that reduce use, avoid excess, and redistribute surplus. If understood from concept to implementation, the HazMart is a powerful tool for reducing pollution at the source, tracking inventory storage, controlling usage and flow, and summarizing data for reporting requirements. Pharmacy options can range from a strict, single control point for all hazardous materials to a virtual system, where the inventory is user controlled and reported over a common system. Designing and implementing HazMarts on large, diverse installations or facilities present a unique set of issues. This is especially true of research and development (R and D) facilities where the chemical use requirements are extensive and often classified. There are often multiple sources of supply; a wide variety of chemical requirements; a mix of containers ranging from small ampoules to large bulk storage tanks; and a wide range of tools used to track hazardous materials, ranging from simple purchase inventories to sophisticated tracking software. Computer systems are often not uniform in capacity, capability, or operating systems, making it difficult to use a server-based unified tracking system software. Each of these issues has a solution or set of solutions tied to fundamental business practices. Each requires an understanding of the problem at hand, which, in turn, requires good communication among all

Hazards analysis of TNX Large Melter-Off-Gas System

International Nuclear Information System (INIS)

Randall, C.T.

1982-03-01

Analysis of the potential safety hazards and an evaluation of the engineered safety features and administrative controls indicate that the LMOG System can be operated without undue hazard to employees or the public, or damage to equipment. The safety features provided in the facility design coupled with the planned procedural and administrative controls make the occurrence of serious accidents very improbable. A set of recommendations evolved during this analysis that was judged potentially capable of further reducing the probability of personnel injury or further mitigating the consequences of potential accidents. These recommendations concerned areas such as formic acid vapor hazards, hazard of feeding water to the melter at an uncontrolled rate, prevention of uncontrolled glass pours due to melter pressure excursions and additional interlocks. These specific suggestions were reviewed with operational and technical personnel and are being incorporated into the process. The safeguards provided by these recommendations are discussed in this report

AN ENHANCED HAZARD ANALYSIS PROCESS FOR THE HANFORD TANK FARMS

International Nuclear Information System (INIS)

SHULTZ MV

2008-01-01

CH2M HILL Hanford Group, Inc., has expanded the scope and increased the formality of process hazards analyses performed on new or modified Tank Farm facilities, designs, and processes. The CH2M HILL process hazard analysis emphasis has been altered to reflect its use as a fundamental part of the engineering and change control process instead of simply being a nuclear safety analysis tool. The scope has been expanded to include identification of accidents/events that impact the environment, or require emergency response, in addition to those with significant impact to the facility worker, the offsite, and the 100-meter receptor. Also, there is now an expectation that controls will be identified to address all types of consequences. To ensure that the process has an appropriate level of rigor and formality, a new engineering standard for process hazards analysis was created. This paper discusses the role of process hazards analysis as an information source for not only nuclear safety, but also for the worker-safety management programs, emergency management, environmental programs. This paper also discusses the role of process hazards analysis in the change control process, including identifying when and how it should be applied to changes in design or process

Safety, health and environmental committee (JKSHE): Establishing chemical hazard management

International Nuclear Information System (INIS)

Shyen, A.K.S.; Noriah Mod Ali; Sangau, J.K.

2012-01-01

Most of the laboratories in Malaysian Nuclear Agency are using chemicals in their research activities. However, it is known that using of chemicals without proper knowledge especially on the material characteristics as well as safe handling procedure may cause great harm to the workers. Therefore, Safety, Health and Environmental Committee (JKSHE) sees the need to establish a good chemical hazard management to ensure that a safe and healthy workplace and environment is provided. One of the elements in chemical hazard management is to carry out Chemical Hazard Risk Assessment (CHRA). The assessment was done so that decision can be made on suitable control measures upon use of such chemicals, such as induction and training courses to be given to the workers and health surveillance activities that may be needed to protect the workers. For this, JKSHE has recommended to conduct CHRA for one of the laboratories at Secondary Standard Dosimetry Laboratory (SSDL) namely Film Dosimeter Processing Room (dark room) as the initial effort towards a better chemical hazard management. This paper presents the case study where CHRA was conducted to identify the chemical hazards at the selected laboratory, the adequacy of existing control measures and finally the recommendation for more effective control measures. (author)

The transport of hazardous materials

International Nuclear Information System (INIS)

Goemmel, F.

1987-01-01

The rapid development of all kinds of transports has been leading to a continuously increasing number of accidents involving the release and escape of hazardous materials. The risks involved for men and the environment have to be realized and reduced to a minimum. Efforts in this field have meanwhile been accumulating an enormous quantity of rules, recommendations and regulations. They comprise, among others, both national and international rail transport, maritime transport, inland shipping, air and road transport regulations adding up to a total of about 5000 pages. The publication discusses the necessity and justification of the existing quantity of regulations, it deals with their possible simplification and modified user-oriented arrangement as well as with a possible international harmonization of regulations. Apart from giving a general survey of the transport of hazardous materials the author reviews the intensive efforts which are going into the safety of the transport of hazardous materials and points out technical and legal problems which have remained unsolved so far. The publication essentially contributes to clearing up the background, perspectives and prospects of the complex regulations controlling the transport of hazardous materials. (orig./HP) [de

Traffic Incident Clearance Time and Arrival Time Prediction Based on Hazard Models

Directory of Open Access Journals (Sweden)

Yang beibei Ji

2014-01-01

Full Text Available Accurate prediction of incident duration is not only important information of Traffic Incident Management System, but also an effective input for travel time prediction. In this paper, the hazard based prediction models are developed for both incident clearance time and arrival time. The data are obtained from the Queensland Department of Transport and Main Roads’ STREAMS Incident Management System (SIMS for one year ending in November 2010. The best fitting distributions are drawn for both clearance and arrival time for 3 types of incident: crash, stationary vehicle, and hazard. The results show that Gamma, Log-logistic, and Weibull are the best fit for crash, stationary vehicle, and hazard incident, respectively. The obvious impact factors are given for crash clearance time and arrival time. The quantitative influences for crash and hazard incident are presented for both clearance and arrival. The model accuracy is analyzed at the end.

Robotic and user interface solutions for hazardous and remote applications

International Nuclear Information System (INIS)

Schempf, H.

1997-01-01

Carnegie Mellon University (CMU) is developing novel robotic and user interface systems to assist in the cleanup activities undertaken by the U.S. Department of Energy (DOE). Under DOE's EM-50 funding and administered by the Federal Energy Technology Center (FETC), CMU has developed a novel asbestos pipe-insulation abatement robot system, called BOA, and a novel generic user interface control and training console, dubbed RoboCon. The use of BOA will allow the speedier abatement of the vast DOE piping networks clad with hazardous and contaminated asbestos insulation by which overall job costs can be reduced by as much as 50%. RoboCon will allow the DOE to evaluate different remote and robotic system technologies from the overall man-machine performance standpoint, as well as provide a standardized training platform for training site operators in the operation of remote and robotic equipment

Hazard Analysis for Pneumatic Flipper Suitport/Z-1 Manned Evaluation, Chamber B, Building 32. Revision: Basic

Science.gov (United States)