The hazard to man of accidental releases of tritium

International Nuclear Information System (INIS)

Brearley, I.R.

1985-03-01

Some aspects of the atmospheric dispersion of tritium are discussed, followed by consideration of the dosimetric pathways. In order to assess the significance of a tritium release the doses from various pathways are estimated and compared with the doses estimated from a similar release of iodine-131. The major hazard from tritium is the ingestion of contaminated food products. For similar releases of tritium and I 131 the ingestion hazard can be comparable if the release occurs near and before the end of the harvest season. However, in the tritium release case the agricultural season influences the consequences markedly and, at other times during the year, the ingestion hazard from tritium may be approximately 20 times less. The dose from inhalation of tritium is sensitive to its chemical form and for similar releases of tritiated water and tritium gas then the dose from tritiated water is approximately 10 4 greater than the dose from tritium gas. For similar releases of tritiated water and iodine-131 then a comparison of the inhalation shows that the dose from the iodine is approximately 300 times greater. (author)

Integrated risk reduction framework to improve railway hazardous materials transportation safety.

Science.gov (United States)

Liu, Xiang; Saat, M Rapik; Barkan, Christopher P L

2013-09-15

Rail transportation plays a critical role to safely and efficiently transport hazardous materials. A number of strategies have been implemented or are being developed to reduce the risk of hazardous materials release from train accidents. Each of these risk reduction strategies has its safety benefit and corresponding implementation cost. However, the cost effectiveness of the integration of different risk reduction strategies is not well understood. Meanwhile, there has been growing interest in the U.S. rail industry and government to best allocate resources for improving hazardous materials transportation safety. This paper presents an optimization model that considers the combination of two types of risk reduction strategies, broken rail prevention and tank car safety design enhancement. A Pareto-optimality technique is used to maximize risk reduction at a given level of investment. The framework presented in this paper can be adapted to address a broader set of risk reduction strategies and is intended to assist decision makers for local, regional and system-wide risk management of rail hazardous materials transportation. Copyright © 2013 Elsevier B.V. All rights reserved.

Advanced Materials Laboratory hazards assessment document

Energy Technology Data Exchange (ETDEWEB)

Barnett, B.; Banda, Z.

1995-10-01

The Department of Energy Order 55OO.3A requires facility-specific hazards assessments be prepared, maintained, and used for emergency planning purposes. This hazards assessment document describes the chemical and radiological hazards associated with the AML. The entire inventory was screened according to the potential airborne impact to onsite and offsite individuals. The air dispersion model, ALOHA, estimated pollutant concentrations downwind from the source of a release, taking into consideration the toxicological and physical characteristics of the release site, the atmospheric conditions, and the circumstances of the release. The greatest distance at which a postulated facility event will produce consequences exceeding the Early Severe Health Effects threshold is 23 meters. The highest emergency classification is a General Emergency. The Emergency Planning Zone is a nominal area that conforms to DOE boundaries and physical/jurisdictional boundaries such as fence lines and streets.

Criticality analysis for hazardous materials transportation; Classificacao da criticidade das rotas do transporte rodoviario de produtos perigosos da BRASKEM

Energy Technology Data Exchange (ETDEWEB)

Oliveira, Katia; Brady, Mariana [Det Norske Veritas (DNV), Rio de Janeiro, RJ (Brazil); Diniz, Americo [BRASKEM S.A., Sao Paulo, SP (Brazil)

2008-07-01

The bad conditions of Brazilians roads drive the companies to be more exigent with the transportation of hazardous materials to avoid accidents or materials releases with actions to contain the releases to community and water sources. To minimize this situation, DNV and BRASKEM developed a methodology for risk analysis called Criticality Analysis for Hazardous Materials Transportation. The objective of this methodology is identifying the most critical points of routes to make actions to avoid accidents. (author)

Transportation of Hazardous Materials Emergency Preparedness Hazards Assessment

Energy Technology Data Exchange (ETDEWEB)

Blanchard, A.

2000-02-28

This report documents the Emergency Preparedness Hazards Assessment (EPHA) for the Transportation of Hazardous Materials (THM) at the Department of Energy (DOE) Savannah River Site (SRS). This hazards assessment is intended to identify and analyze those transportation hazards significant enough to warrant consideration in the SRS Emergency Management Program.

Transportation of Hazardous Materials Emergency Preparedness Hazards Assessment

International Nuclear Information System (INIS)

Blanchard, A.

2000-01-01

This report documents the Emergency Preparedness Hazards Assessment (EPHA) for the Transportation of Hazardous Materials (THM) at the Department of Energy (DOE) Savannah River Site (SRS). This hazards assessment is intended to identify and analyze those transportation hazards significant enough to warrant consideration in the SRS Emergency Management Program

Transportation of hazardous materials emergency preparedness hazards assessment

International Nuclear Information System (INIS)

Blanchard, A.

2000-01-01

This report documents the Emergency Preparedness Hazards Assessment (EPHA) for the Transportation of Hazardous Materials (THM) at the Department of Energy (DOE) Savannah River Site (SRS). This hazards assessment is intended to identify and analyze those transportation hazards significant enough to warrant consideration in the SRS Emergency Management Program

Reporting continuous releases of hazardous and extremely hazardous substances under CERCLA and EPCRA

International Nuclear Information System (INIS)

1995-01-01

This guidance is designed to provide basic instruction to US DOE and DOE operations contractor personnel on how to characterize CERCLA and EPCRA hazardous substance releases as continuous and how to prepare and deliver continuousreleasee reports to Federal, State, and local authorities. DOE staff should use this guidance as an overview of the continuous release requirements, a quick ready reference guide for specific topics concerning continuous releases and a step-by-step guide for the process of identifying and reporting continuous releases

Hazards assessment for the Hazardous Waste Storage Facility

International Nuclear Information System (INIS)

Knudsen, J.K.; Calley, M.B.

1994-04-01

This report documents the hazards assessment for the Hazardous Waste Storage Facility (HWSF) located at the Idaho National Engineering Laboratory. The hazards assessment was performed to ensure that this facility complies with DOE and company requirements pertaining to emergency planning and preparedness for operational emergencies. The hazards assessment identifies and analyzes hazards that are significant enough to warrant consideration in a facility's operational emergency management program. The area surrounding HWSF, the buildings and structures at HWSF, and the processes used at HWSF are described in this report. All nonradiological hazardous materials at the HWSF were identified (radiological hazardous materials are not stored at HWSF) and screened against threshold quantities according to DOE Order 5500.3A guidance. Two of the identified hazardous materials exceeded their specified threshold quantity. This report discusses the potential release scenarios and consequences associated with an accidental release for each of the two identified hazardous materials, lead and mercury. Emergency considerations, such as emergency planning zones, emergency classes, protective actions, and emergency action levels, are also discussed based on the analysis of potential consequences. Evaluation of the potential consequences indicated that the highest emergency class for operational emergencies at the HWSF would be a Site Area Emergency

Transportation of Hazardous Evidentiary Material.

Energy Technology Data Exchange (ETDEWEB)

Osborn, Douglas.

2005-06-01

This document describes the specimen and transportation containers currently available for use with hazardous and infectious materials. A detailed comparison of advantages, disadvantages, and costs of the different technologies is included. Short- and long-term recommendations are also provided.3 DraftDraftDraftExecutive SummaryThe Federal Bureau of Investigation's Hazardous Materials Response Unit currently has hazardous material transport containers for shipping 1-quart paint cans and small amounts of contaminated forensic evidence, but the containers may not be able to maintain their integrity under accident conditions or for some types of hazardous materials. This report provides guidance and recommendations on the availability of packages for the safe and secure transport of evidence consisting of or contaminated with hazardous chemicals or infectious materials. Only non-bulk containers were considered because these are appropriate for transport on small aircraft. This report will addresses packaging and transportation concerns for Hazardous Classes 3, 4, 5, 6, 8, and 9 materials. If the evidence is known or suspected of belonging to one of these Hazardous Classes, it must be packaged in accordance with the provisions of 49 CFR Part 173. The anthrax scare of several years ago, and less well publicized incidents involving unknown and uncharacterized substances, has required that suspicious substances be sent to appropriate analytical laboratories for analysis and characterization. Transportation of potentially hazardous or infectious material to an appropriate analytical laboratory requires transport containers that maintain both the biological and chemical integrity of the substance in question. As a rule, only relatively small quantities will be available for analysis. Appropriate transportation packaging is needed that will maintain the integrity of the substance, will not allow biological alteration, will not react chemically with the substance being

New York hazardous substances emergency events surveillance: learning from hazardous substances releases to improve safety

International Nuclear Information System (INIS)

Welles, Wanda Lizak; Wilburn, Rebecca E.; Ehrlich, Jenny K.; Floridia, Christina M.

2004-01-01

Since 1993, the New York State Department of Health, funded by the Agency for Toxic Substances and Disease Registry, has collected data about non-petroleum hazardous substances releases through the Hazardous Substances Emergency Events Surveillance (NYHSEES) project. This study investigates risk factors for hazardous substances releases that may result in public health consequences such as injury or reported health effects. The 6428 qualifying events that occurred during the 10-year-period of 1993-2002 involved 8838 hazardous substances, 842 evacuations, more than 75,419 people evacuated, and more than 3120 people decontaminated. These events occurred both at fixed facilities (79%) and during transport (21%). The causative factors most frequently contributing to reported events were equipment failure (39%) and human error (33%). Five of the 10 chemicals most frequently associated with injuries were also among the 10 chemicals most frequently involved in reported events: sulfuric acid, hydrochloric acid, ammonia, sodium hypochlorite, and carbon monoxide. The chemical categories most frequently associated with events, and with events with adverse health effects were volatile organic compounds (VOCs) and solvents, and acids. Events with releases of hazardous substances were associated with injuries to 3089 people including employees (37%), responders (12%), the general public (29%) and students (22%). The most frequently reported adverse health effects were respiratory irritation, headache, and nausea or vomiting. Most of the injured were transported to the hospital, treated, and released (55%) or treated at the scene (29%). These data have been used for emergency response training, planning, and prevention activities to reduce morbidity and mortality from future events

Toxics Release Inventory Chemical Hazard Information Profiles (TRI-CHIP) Dataset

Data.gov (United States)

U.S. Environmental Protection Agency — The Toxics Release Inventory (TRI) Chemical Hazard Information Profiles (TRI-CHIP) dataset contains hazard information about the chemicals reported in TRI. Users can...

A set of integrated environmental transport and diffusion models for calculating hazardous releases

International Nuclear Information System (INIS)

Pepper, D.W.

1996-01-01

A set of numerical transport and dispersion models is incorporated within a graphical interface shell to predict hazardous material released into the environment. The visual shell (EnviroView) consists of an object-oriented knowledge base, which is used for inventory control, site mapping and orientation, and monitoring of materials. Graphical displays of detailed sites, building locations, floor plans, and three-dimensional views within a room are available to the user using a point and click interface. In the event of a release to the environment, the user can choose from a selection of analytical, finite element, finite volume, and boundary element methods, which calculate atmospheric transport, groundwater transport, and dispersion within a building interior. The program runs on 486 personal computers under WINDOWS

Hazardous materials

Science.gov (United States)

... substances that could harm human health or the environment. Hazardous means dangerous, so these materials must be ... M. is also a founding member of Hi-Ethics and subscribes to the principles of the Health ...

Estimated airborne release of plutonium from Westinghouse Cheswick site as a result of postulated damage from severe wind and seismic hazard

International Nuclear Information System (INIS)

Mishima, J.; Schwendiman, L.C.; Ayer, J.E.

1979-06-01

The potential airborne releases of plutonium (source terms) from postulated damage sustained by the Westinghouse Plutonium Fuel Development Laboratories at the Cheswick site in Pennsylvania as a result of various levels of wind and seismic hazard are estimated. The source terms are based on damage scenarios originated by other specialists and range up to 260 mph for wind hazard and in excess of 0.39 g ground acceleration for seismic hazard. The approaches and factors used to estimate the source terms (inventories of dispersible materials at risk, damage levels and ratios, fractional airborne releases of dispersible materials under stress, atmosphere exchange rates, and source term ranges) are discussed. Source term estimates range from less than 10 -7 g plutonium to greater than 130 g plutonium over a four-day period

Just-in-Time techniques as applied to hazardous materials management

OpenAIRE

Spicer, John S.

1996-01-01

Approved for public release; distribution is unlimited This study investigates the feasibility of integrating JIT techniques in the context of hazardous materials management. This study provides a description of JIT, a description of environmental compliance issues and the outgrowth of related HAZMAT policies, and a broad perspective on strategies for applying JIT to HAZMAT management. http://archive.org/details/justintimetechn00spic Lieutenant Commander, United States Navy

The release of lindane from contaminated building materials.

Science.gov (United States)

Volchek, Konstantin; Thouin, Geneviève; Kuang, Wenxing; Li, Ken; Tezel, F Handan; Brown, Carl E

2014-10-01

The release of the organochlorine pesticide lindane (γ-hexachlorocyclohexane) from several types of contaminated building materials was studied to assess inhalation hazard and decontamination requirements in response to accidental and/or intentional spills. The materials included glass, polypropylene carpet, latex-painted drywall, ceramic tiles, vinyl floor tiles, and gypsum ceiling tiles. For each surface concentration, an equilibrium concentration was determined in the vapour phase of the surrounding air. Vapor concentrations depended upon initial surface concentration, temperature, and type of building material. A time-weighted average (TWA) concentration in the air was used to quantify the health risk associated with the inhalation of lindane vapors. Transformation products of lindane, namely α-hexachlorocyclohexane and pentachlorocyclohexene, were detected in the vapour phase at both temperatures and for all of the test materials. Their formation was greater on glass and ceramic tiles, compared to other building materials. An empiric Sips isotherm model was employed to approximate experimental results and to estimate the release of lindane and its transformation products. This helped determine the extent of decontamination required to reduce the surface concentrations of lindane to the levels corresponding to vapor concentrations below TWA.

Hazard index for underground toxic material

International Nuclear Information System (INIS)

Smith, C.F.; Cohen, J.J.; McKone, T.E.

1980-06-01

To adequately define the problem of waste management, quantitative measures of hazard must be used. This study reviews past work in the area of hazard indices and proposes a geotoxicity hazard index for use in characterizing the hazard of toxic material buried underground. Factors included in this index are: an intrinsic toxicity factor, formulated as the volume of water required for dilution to public drinking-water levels; a persistence factor to characterize the longevity of the material, ranging from unity for stable materials to smaller values for shorter-lived materials; an availability factor that relates the transport potential for the particular material to a reference value for its naturally occurring analog; and a correction factor to accommodate the buildup of decay progeny, resulting in increased toxicity

Hazard index for underground toxic material

Energy Technology Data Exchange (ETDEWEB)

Smith, C.F.; Cohen, J.J.; McKone, T.E.

1980-06-01

To adequately define the problem of waste management, quantitative measures of hazard must be used. This study reviews past work in the area of hazard indices and proposes a geotoxicity hazard index for use in characterizing the hazard of toxic material buried underground. Factors included in this index are: an intrinsic toxicity factor, formulated as the volume of water required for dilution to public drinking-water levels; a persistence factor to characterize the longevity of the material, ranging from unity for stable materials to smaller values for shorter-lived materials; an availability factor that relates the transport potential for the particular material to a reference value for its naturally occurring analog; and a correction factor to accommodate the buildup of decay progeny, resulting in increased toxicity.

Written instructions for the transport of hazardous materials: Accident management instruction sheets

International Nuclear Information System (INIS)

Ridder, K.

1988-01-01

In spite of the regulations and the safety provisions taken, accidents are not entirely avoidable in the transport of hazardous materials. For managing an accident and preventing further hazards after release of dangerous substances, the vehicle drivers must carry with them the accident management instruction sheets, which give instructions on immediate counter measures to be taken by the driver, and on information to be given to the police and the fire brigades. The article in hand discusses the purpose, the contents, and practice-based improvement of this collection of instruction sheets. Particular reference is given to the newly revised version of June 15, 1988 (Verkehrsblatt 1/88) of the 'Directives for setting up accident management instruction sheets - written instructions - for road transport of hazardous materials', as issued by the Federal Ministry of Transport. (orig./HP) [de

Transportation of hazardous and nuclear materials

International Nuclear Information System (INIS)

Boryczka, M.; Shaver, D.

1989-01-01

Transportation of hazardous and radioactive materials is a vital part of the nation's economy. In recent years public concern over the relative safety of transporting hazardous materials has risen sharply. The United States has a long history of transporting hazardous and radioactive material; rocket propellants, commercial spent fuel, low-level and high-level radioactive waste has been shipped for years. While the track record for shipping these materials is excellent, the knowledge that hazardous materials are passing through communities raises the ire of citizens and local governments. Public outcry over shipments containing hazardous cargo has been especially prominent when shippers have attempted to transport rocket propellants or spent nuclear fuel. Studies of recent shipments have provided insight into the difficulties of shipping in a politically charged environment, the major issues of concern to citizens, and some of the more successful methods of dealing with public concerns. This paper focuses on lessons learned from these studies which include interviews with shippers, carriers, and regulators

Hazardous material reduction initiative

International Nuclear Information System (INIS)

Nichols, D.H.

1995-02-01

The Hazardous Material Reduction Initiative (HMRI) explores using the review of purchase requisitions to reduce both the use of hazardous materials and the generation of regulated and nonregulated wastes. Based on an 11-month program implemented at the Hanford Site, hazardous material use and waste generation was effectively reduced by using a centralized procurement control program known as HMRI. As expected, several changes to the original proposal were needed during the development/testing phase of the program to accommodate changing and actual conditions found at the Hanford Site. The current method requires a central receiving point within the Procurement Organization to review all purchase requisitions for potentially Occupational Safety and Health Administration (OSHA) hazardous products. Those requisitions (approximately 4% to 6% of the total) are then forwarded to Pollution Prevention personnel for evaluation under HMRI. The first step is to determine if the requested item can be filled by existing or surplus material. The requisitions that cannot filled by existing or surplus material are then sorted into two groups based on applicability to the HMRI project. For example, laboratory requests for analytical reagents or standards are excluded and the purchase requisitions are returned to Procurement for normal processing because, although regulated, there is little opportunity for source reduction due to the strict protocols followed. Each item is then checked to determine if it is regulated or not. Regulated items are prioritized based on hazardous contents, quantity requested, and end use. Copies of these requisitions are made and the originals are returned to Procurement within 1-hr. Since changes to the requisition can be made at later stages during procurement, the HMRI fulfills one of its original premises in that it does not slow the procurement process

Incidents with hazardous radiation sources

International Nuclear Information System (INIS)

Schoenhacker, Stefan

2016-01-01

Incidents with hazardous radiation sources can occur in any country, even those without nuclear facilities. Preparedness for such incidents is supposed to fulfill globally agreed minimum standards. Incidents are categorized in incidents with licensed handling of radiation sources as for material testing, transport accidents of hazardous radiation sources, incidents with radionuclide batteries, incidents with satellites containing radioactive inventory, incidents wit not licensed handling of illegally acquired hazardous radiation sources. The emergency planning in Austria includes a differentiation according to the consequences: incidents with release of radioactive materials resulting in restricted contamination, incidents with release of radioactive materials resulting in local contamination, and incidents with the hazard of e@nhanced exposure due to the radiation source.

46 CFR 151.03-30 - Hazardous material.

Science.gov (United States)

2010-10-01

... hazardous material means a liquid material or substance that is— (a) Flammable or combustible; (b) Designated a hazardous substance under section 311(b) of the Federal Water Pollution Control Act (33 U.S.C... Agency designates hazardous substances in 40 CFR Table 116.4A. The Coast Guard designates hazardous...

Hydrothermal Liquefaction Treatment Hazard Analysis Report

Energy Technology Data Exchange (ETDEWEB)

Lowry, Peter P. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wagner, Katie A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2016-09-12

Hazard analyses were performed to evaluate the modular hydrothermal liquefaction treatment system. The hazard assessment process was performed in 2 stages. An initial assessment utilizing Hazard Identification and Preliminary Hazards Analysis (PHA) techniques identified areas with significant or unique hazards (process safety-related hazards) that fall outside of the normal operating envelope of PNNL and warranted additional analysis. The subsequent assessment was based on a qualitative What-If analysis. The analysis was augmented, as necessary, by additional quantitative analysis for scenarios involving a release of hazardous material or energy with the potential for affecting the public. The following selected hazardous scenarios received increased attention: •Scenarios involving a release of hazardous material or energy, controls were identified in the What-If analysis table that prevent the occurrence or mitigate the effects of the release. •Scenarios with significant consequences that could impact personnel outside the immediate operations area, quantitative analyses were performed to determine the potential magnitude of the scenario. The set of “critical controls” were identified for these scenarios (see Section 4) which prevent the occurrence or mitigate the effects of the release of events with significant consequences.

Truck shipment risks for assessing hazardous materials - a new paradigm incorporating safety and security

Energy Technology Data Exchange (ETDEWEB)

Greenberg, A.; McSweeney, T.; Allen, J.; Lepofsky, M. [Battelle Memorial Inst., Columbus, OH (United States); Abkowitz, M. [Dept. of Civil Engineering, Vanderbilt Univ., Nashville, TN (United States)

2004-07-01

Recent terrorist events, most notably September 11, 2001, have taught us that transportation risk management must be performed with a different lens to accommodate terrorism scenarios that would have previously been considered unlikely to warrant serious attention. Given these circumstances, a new paradigm is needed for managing the risks associated with highway transport of hazardous materials. In particular, this paradigm must: 1) more explicitly consider security threat and vulnerability, and 2) integrate security considerations into an overall framework for addressing natural and man-made disasters, be they accidental or planned. This paper summarizes the results of a study sponsored by the U.S. Department of Transportation, Federal Motor Carrier Safety Administration for the purpose of exploring how a paradigm might evolve in which both safety and security risks can be evaluated as a systematic, integrated process. The work was directed at developing a methodology for assessing the impacts of hazardous materials safety and security incident consequences when transported by highway. This included consideration of the manner in which these materials could be involved in initiating events as well as potential outcomes under a variety of release conditions. The methodology is subsequently applied to various classes of hazardous materials to establish an economic profile of the impacts that might be expected if a major release were to occur. The paper concludes with a discussion of the findings and implications associated with this effort.

Truck shipment risks for assessing hazardous materials - a new paradigm incorporating safety and security

International Nuclear Information System (INIS)

Greenberg, A.; McSweeney, T.; Allen, J.; Lepofsky, M.; Abkowitz, M.

2004-01-01

Recent terrorist events, most notably September 11, 2001, have taught us that transportation risk management must be performed with a different lens to accommodate terrorism scenarios that would have previously been considered unlikely to warrant serious attention. Given these circumstances, a new paradigm is needed for managing the risks associated with highway transport of hazardous materials. In particular, this paradigm must: 1) more explicitly consider security threat and vulnerability, and 2) integrate security considerations into an overall framework for addressing natural and man-made disasters, be they accidental or planned. This paper summarizes the results of a study sponsored by the U.S. Department of Transportation, Federal Motor Carrier Safety Administration for the purpose of exploring how a paradigm might evolve in which both safety and security risks can be evaluated as a systematic, integrated process. The work was directed at developing a methodology for assessing the impacts of hazardous materials safety and security incident consequences when transported by highway. This included consideration of the manner in which these materials could be involved in initiating events as well as potential outcomes under a variety of release conditions. The methodology is subsequently applied to various classes of hazardous materials to establish an economic profile of the impacts that might be expected if a major release were to occur. The paper concludes with a discussion of the findings and implications associated with this effort

RELEASE OF DRIED RADIOACTIVE WASTE MATERIALS TECHNICAL BASIS DOCUMENT

International Nuclear Information System (INIS)

KOZLOWSKI, S.D.

2007-01-01

This technical basis document was developed to support RPP-23429, Preliminary Documented Safety Analysis for the Demonstration Bulk Vitrification System (PDSA) and RPP-23479, Preliminary Documented Safety Analysis for the Contact-Handled Transuranic Mixed (CH-TRUM) Waste Facility. The main document describes the risk binning process and the technical basis for assigning risk bins to the representative accidents involving the release of dried radioactive waste materials from the Demonstration Bulk Vitrification System (DBVS) and to the associated represented hazardous conditions. Appendices D through F provide the technical basis for assigning risk bins to the representative dried waste release accident and associated represented hazardous conditions for the Contact-Handled Transuranic Mixed (CH-TRUM) Waste Packaging Unit (WPU). The risk binning process uses an evaluation of the frequency and consequence of a given representative accident or represented hazardous condition to determine the need for safety structures, systems, and components (SSC) and technical safety requirement (TSR)-level controls. A representative accident or a represented hazardous condition is assigned to a risk bin based on the potential radiological and toxicological consequences to the public and the collocated worker. Note that the risk binning process is not applied to facility workers because credible hazardous conditions with the potential for significant facility worker consequences are considered for safety-significant SSCs and/or TSR-level controls regardless of their estimated frequency. The controls for protection of the facility workers are described in RPP-23429 and RPP-23479. Determination of the need for safety-class SSCs was performed in accordance with DOE-STD-3009-94, Preparation Guide for US. Department of Energy Nonreactor Nuclear Facility Documented Safety Analyses, as described below

Hazardous materials routing - risk management of mismanagement

International Nuclear Information System (INIS)

Glickman, T.S.

1988-01-01

Along with emergency planning and preparedness, the placement of restrictions on routing has become an increasingly popular device for managing the highway and rail risks of hazardous materials transportation. Federal studies conducted in 1985 indicate that at that time there were 513 different state and local restrictions on the routing of hazardous materials for these two modes of transportation, and that there were 136 state and local notification requirements, that is, restrictions that take the form of a statute or ordinance requiring advance warning or periodic reporting about hazardous materials shipments. Routing restrictions also take the form of prohibiting the use of road, a tunnel, or a bridge for a specified set of hazardous materials

76 FR 51324 - Hazardous Materials: Incorporating Rail Special Permits Into the Hazardous Materials Regulations

Science.gov (United States)

2011-08-18

... through use of electronic data interchange (EDI). The IVOHMA states ``differences in hazard communication... and on the possible effects EDI may have on distributing hazardous materials shipping paper... consider the use of EDI in other modes of transport in a future rulemaking. Petition No. P-1567 PHMSA...

Integrated risk reduction framework to improve railway hazardous materials transportation safety

Energy Technology Data Exchange (ETDEWEB)

Liu, Xiang, E-mail: liu94@illinois.edu; Saat, M. Rapik, E-mail: mohdsaat@illinois.edu; Barkan, Christopher P.L., E-mail: cbarkan@illinois.edu

2013-09-15

Highlights: • An integrated framework is developed to optimize risk reduction. • A negative binomial regression model is developed to analyze accident-cause-specific railcar derailment probability. • A Pareto-optimality technique is applied to determine the lowest risk given any level of resource. • A multi-attribute decision model is developed to determine the optimal amount of investment for risk reduction. • The models could aid the government and rail industry in developing cost-efficient risk reduction policy and practice. -- Abstract: Rail transportation plays a critical role to safely and efficiently transport hazardous materials. A number of strategies have been implemented or are being developed to reduce the risk of hazardous materials release from train accidents. Each of these risk reduction strategies has its safety benefit and corresponding implementation cost. However, the cost effectiveness of the integration of different risk reduction strategies is not well understood. Meanwhile, there has been growing interest in the U.S. rail industry and government to best allocate resources for improving hazardous materials transportation safety. This paper presents an optimization model that considers the combination of two types of risk reduction strategies, broken rail prevention and tank car safety design enhancement. A Pareto-optimality technique is used to maximize risk reduction at a given level of investment. The framework presented in this paper can be adapted to address a broader set of risk reduction strategies and is intended to assist decision makers for local, regional and system-wide risk management of rail hazardous materials transportation.

30 CFR 56.16004 - Containers for hazardous materials.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Containers for hazardous materials. 56.16004 Section 56.16004 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... Storage and Handling § 56.16004 Containers for hazardous materials. Containers holding hazardous materials...

30 CFR 57.16004 - Containers for hazardous materials.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Containers for hazardous materials. 57.16004 Section 57.16004 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... Storage and Handling § 57.16004 Containers for hazardous materials. Containers holding hazardous materials...

Hazardous materials and waste management a guide for the professional hazards manager

CERN Document Server

Cheremisinoff, Nicholas P

1995-01-01

The management of hazardous materials and industrial wastes is complex, requiring a high degree of knowledge over very broad technical and legal subject areas. Hazardous wastes and materials are diverse, with compositions and properties that not only vary significantly between industries, but within industries, and indeed within the complexity of single facilities. Proper management not only requires an understanding of the numerous and complex regulations governing hazardous materials and waste streams, but an understanding and knowledge of the treatment, post-treatment, and waste minimizatio

Hazardous substances releases associated with Hurricanes Katrina and Rita in industrial settings, Louisiana and Texas.

Science.gov (United States)

Ruckart, Perri Zeitz; Orr, Maureen F; Lanier, Kenneth; Koehler, Allison

2008-11-15

The scientific literature concerning the public health response to the unprecedented hurricanes striking the Gulf Coast in August and September 2005 has focused mainly on assessing health-related needs and surveillance of injuries, infectious diseases, and other illnesses. However, the hurricanes also resulted in unintended hazardous substances releases in the affected states. Data from two states (Louisiana and Texas) participating in the Hazardous Substances Emergency Events Surveillance (HSEES) system were analyzed to describe the characteristics of hazardous substances releases in industrial settings associated with Hurricanes Katrina and Rita. HSEES is an active multi-state Web-based surveillance system maintained by the Agency for Toxic Substances and Disease Registry (ATSDR). In 2005, 166 hurricane-related hazardous substances events in industrial settings in Louisiana and Texas were reported. Most (72.3%) releases were due to emergency shut downs in preparation for the hurricanes and start-ups after the hurricanes. Emphasis is given to the contributing causal factors, hazardous substances released, and event scenarios. Recommendations are made to prevent or minimize acute releases of hazardous substances during future hurricanes, including installing backup power generation, securing equipment and piping to withstand high winds, establishing procedures to shutdown process operations safely, following established and up-to-date start-up procedures and checklists, and carefully performing pre-start-up safety reviews.

Hazardous substances releases associated with Hurricanes Katrina and Rita in industrial settings, Louisiana and Texas

International Nuclear Information System (INIS)

Ruckart, Perri Zeitz; Orr, Maureen F.; Lanier, Kenneth; Koehler, Allison

2008-01-01

The scientific literature concerning the public health response to the unprecedented hurricanes striking the Gulf Coast in August and September 2005 has focused mainly on assessing health-related needs and surveillance of injuries, infectious diseases, and other illnesses. However, the hurricanes also resulted in unintended hazardous substances releases in the affected states. Data from two states (Louisiana and Texas) participating in the Hazardous Substances Emergency Events Surveillance (HSEES) system were analyzed to describe the characteristics of hazardous substances releases in industrial settings associated with Hurricanes Katrina and Rita. HSEES is an active multi-state Web-based surveillance system maintained by the Agency for Toxic Substances and Disease Registry (ATSDR). In 2005, 166 hurricane-related hazardous substances events in industrial settings in Louisiana and Texas were reported. Most (72.3%) releases were due to emergency shut downs in preparation for the hurricanes and start-ups after the hurricanes. Emphasis is given to the contributing causal factors, hazardous substances released, and event scenarios. Recommendations are made to prevent or minimize acute releases of hazardous substances during future hurricanes, including installing backup power generation, securing equipment and piping to withstand high winds, establishing procedures to shutdown process operations safely, following established and up-to-date start-up procedures and checklists, and carefully performing pre-start-up safety reviews

Hazardous substances releases associated with Hurricanes Katrina and Rita in industrial settings, Louisiana and Texas

Energy Technology Data Exchange (ETDEWEB)

Ruckart, Perri Zeitz [Division of Health Studies, Agency for Toxic Substances and Disease Registry, Atlanta, GA (United States)], E-mail: afp4@cdc.gov; Orr, Maureen F. [Division of Health Studies, Agency for Toxic Substances and Disease Registry, Atlanta, GA (United States); Lanier, Kenneth; Koehler, Allison [Louisiana Department of Health and Hospitals, Office of Public Health, New Orleans, LA (United States)

2008-11-15

The scientific literature concerning the public health response to the unprecedented hurricanes striking the Gulf Coast in August and September 2005 has focused mainly on assessing health-related needs and surveillance of injuries, infectious diseases, and other illnesses. However, the hurricanes also resulted in unintended hazardous substances releases in the affected states. Data from two states (Louisiana and Texas) participating in the Hazardous Substances Emergency Events Surveillance (HSEES) system were analyzed to describe the characteristics of hazardous substances releases in industrial settings associated with Hurricanes Katrina and Rita. HSEES is an active multi-state Web-based surveillance system maintained by the Agency for Toxic Substances and Disease Registry (ATSDR). In 2005, 166 hurricane-related hazardous substances events in industrial settings in Louisiana and Texas were reported. Most (72.3%) releases were due to emergency shut downs in preparation for the hurricanes and start-ups after the hurricanes. Emphasis is given to the contributing causal factors, hazardous substances released, and event scenarios. Recommendations are made to prevent or minimize acute releases of hazardous substances during future hurricanes, including installing backup power generation, securing equipment and piping to withstand high winds, establishing procedures to shutdown process operations safely, following established and up-to-date start-up procedures and checklists, and carefully performing pre-start-up safety reviews.

Estimate of airborne release of plutonium from Babcock and Wilcox plant as a result of severe wind hazard and earthquake

International Nuclear Information System (INIS)

Mishima, J.; Schwendiman, L.C.; Ayer, J.E.

1978-10-01

As part of an interdisciplinary study to evaluate the potential radiological consequences of wind hazard and earthquake upon existing commercial mixed oxide fuel fabrication plants, the potential mass airborne releases of plutonium (source terms) from such events are estimated. The estimated souce terms are based upon the fraction of enclosures damaged to three levels of severity (crush, puncture penetrate, and loss of external filter, in order of decreasing severity), called damage ratio, and the airborne release if all enclosures suffered that level of damage. The discussion of damage scenarios and source terms is divided into wind hazard and earthquake scenarios in order of increasing severity. The largest airborne releases from the building were for cases involving the catastrophic collapse of the roof over the major production areas--wind hazard at 110 mph and earthquakes with peak ground accelerations of 0.20 to 0.29 g. Wind hazards at higher air velocities and earthquakes with higher ground acceleration do not result in significantly greater source terms. The source terms were calculated as additional mass of respirable particles released with time up to 4 days; and, under these assumptions, approximately 98% of the mass of material of concern is made airborne from 2 h to 4 days after the event. The overall building source terms from the damage scenarios evaluated are shown in a table. The contribution of individual areas to the overall building source term is presented in order of increasing severity for wind hazard and earthquake

Report: EPA Provided Quality and Timely Information on Hurricane Katrina Hazardous Material Releases and Debris Management

Science.gov (United States)

Report #2006-P-00023, May 2, 2006. After Hurricane Katrina, EPA was the agency with lead responsibility to prevent, minimize, or mitigate threats to public health and the environment caused by hazardous materials and oil spills in inland zones.

Hazardous Material Packaging and Transportation

Energy Technology Data Exchange (ETDEWEB)

Hypes, Philip A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-02-04

This is a student training course. Some course objectives are to: recognize and use standard international and US customary units to describe activities and exposure rates associated with radioactive material; determine whether a quantity of a single radionuclide meets the definition of a class 7 (radioactive) material; determine, for a given single radionuclide, the shipping quantity activity limits per 49 Code of Federal Regulations (CFR) 173.435; determine the appropriate radioactive material hazard class proper shipping name for a given material; determine when a single radionuclide meets the DOT definition of a hazardous substance; determine the appropriate packaging required for a given radioactive material; identify the markings to be placed on a package of radioactive material; determine the label(s) to apply to a given radioactive material package; identify the entry requirements for radioactive material labels; determine the proper placement for radioactive material label(s); identify the shipping paper entry requirements for radioactive material; select the appropriate placards for a given radioactive material shipment or vehicle load; and identify allowable transport limits and unacceptable transport conditions for radioactive material.

Temporary shelter-in-place as protection against a release of airborne hazardous material : report of a literature search.; TOPICAL

International Nuclear Information System (INIS)

Yantosik, G. D.; Lerner, K.; Maloney, D. M.

2002-01-01

''Temporary shelter-in place'' is the combination of prompt shelter-in-place (SIP) to minimize initial exposure to airborne hazardous material, followed by timely action to terminate this protection to minimize exposure to hazardous vapor accumulations in the shelter once the air outside becomes less hazardous than the air inside the shelter. Temporary SIP, if properly executed, is considered to be an effective way to protect populations from hazardous chemical vapors, especially from high concentrations for short periods. This is supported by laboratory and field experiments. The need for timely termination of temporary SIP as protection from infiltrated vapors is an integral component of a temporary SIP strategy. It was from this premise that Argonne National Laboratory (ANL) was asked to develop methodologies for deciding when and how to terminate SIP. These methodologies, in turn, could be the basis for site-specific operational guidelines (e.g., decision matrix, decision-tree, or algorithm) for terminating SIP on each of the eight Army chemical stockpile storage sites, and in the off-post communities surrounding them. This project consists of two tasks. Task 1 was to collect and analyze existing literature that might be relevant to the termination of temporary SIP. This report is the product of Task 1. Task 2, which will begin on 2 February 2001, will use the results of the literature search as the baseline to investigate the concepts associated with temporary SIP, and to develop methodologies for termination of temporary SIP that can be incorporated in site-specific operational guidelines. It is understood that these methods will be consistent with Chemical Stockpile Emergency Preparedness Program (CSEPP) policy that ''the most important objective of the emergency preparedness and implementation process is the avoidance of fatalities to the maximum extent practicable, should an accidental release of chemical agent occur.'' It is also anticipated that these

Health and safety information program for hazardous materials

International Nuclear Information System (INIS)

O'Brien, M.P.; Fallon, N.J.; Kuehner, A.V.

1979-01-01

The system is used as a management tool in several safety and health programs. It is used to: trace the use of hazardous materials and to determine monitoring needs; inform the occupational physician of the potential health problems associated with materials ordered by a given individual; inform the fire and rescue group of hazardous materials in a given building; provide waste disposal recommendations to the hazardous waste management group; assist the hazardous materials shipping coordinator in identifying materials which are regulated by the Department of Transportation; and guide management decisions in the area of recognizing and rectifying unsafe conditions. The information system has been expanded from a manual effort to provide a brief description of health hazards of chemicals used at the lab to a computerized health and safety information system which serves the needs of all personnel who may encounter the material in the course of their work. The system has been designed to provide information needed to control the potential problems associated with a hazardous material up to the time that it is consumed in a given operation or is sent to the waste disposal facility

The National Shipbuilding Research Program, 1990 Ship Production Symposium, Paper No. 4B-1: Solving SARA Compliance with Computerized Hazardous Materials Tracking

National Research Council Canada - National Science Library

Johnston, Don; Schoenleber, Dave

1990-01-01

...) has forced facilities to keep track of hazardous materials as never before. EPCRA contains five major reporting requirements including planning notification, emergency release notification, Material Safety Data Sheet (MSDS...

78 FR 24309 - Pipeline and Hazardous Materials Safety Administration

Science.gov (United States)

2013-04-24

... DEPARTMENT OF TRANSPORTATION Pipeline and Hazardous Materials Safety Administration List of Special Permit Applications Delayed AGENCY: Pipeline and Hazardous Materials Safety Administration (PHMSA..., Pipeline and Hazardous Materials Safety Administration, U.S. Department of Transportation, East Building...

76 FR 45332 - Pipeline and Hazardous Materials Safety Administration

Science.gov (United States)

2011-07-28

... DEPARTMENT OF TRANSPORTATION Pipeline and Hazardous Materials Safety Administration Office of... Hazardous Materials Safety Administration (PHMSA), DOT. ACTION: List of Applications for Modification of..., 2011. ADDRESSES: Record Center, Pipeline and Hazardous Materials Safety Administration, U.S. Department...

Transportation of hazardous materials (hazmat) a literature survey

OpenAIRE

Zafer YILMAZ; Serpil EROL; Hakan Soner APLAK

2016-01-01

ransportation has a great role in logistics. Many researchers have studied on transportation and vehicle routing problems. Transportation of hazardous materials (hazmat) is a special subject for logistics. Causalities due to the accidents caused by trucks carrying hazardous materials will be intolerable. Many researchers have studied on risk assessment of hazmat transportation to find ways for reducing hazardous material transportation risks. Some researchers have studied routing of hazmat tr...

Idaho National Engineering Laboratory response to the December 13, 1991, Congressional inquiry on offsite release of hazardous and solid waste containing radioactive materials from Department of Energy facilities

International Nuclear Information System (INIS)

Shapiro, C.; Garcia, K.M.; McMurtrey, C.D.; Williams, K.L.; Jordan, P.J.

1992-05-01

This report is a response to the December 13, 1991, Congressional inquiry that requested information on all hazardous and solid waste containing radioactive materials sent from Department of Energy facilities to offsite facilities for treatment or disposal since January 1, 1981. This response is for the Idaho National Engineering Laboratory. Other Department of Energy laboratories are preparing responses for their respective operations. The request includes ten questions, which the report divides into three parts, each responding to a related group of questions. Part 1 answers Questions 5, 6, and 7, which call for a description of Department of Energy and contractor documentation governing the release of waste containing radioactive materials to offsite facilities. ''Offsite'' is defined as non-Department of Energy and non-Department of Defense facilities, such as commercial facilities. Also requested is a description of the review process for relevant release criteria and a list of afl Department of Energy and contractor documents concerning release criteria as of January 1, 1981. Part 2 answers Questions 4, 8, and 9, which call for information about actual releases of waste containing radioactive materials to offsite facilities from 1981 to the present, including radiation levels and pertinent documentation. Part 3 answers Question 10, which requests a description of the process for selecting offsite facilities for treatment or disposal of waste from Department of Energy facilities. In accordance with instructions from the Department of Energy, the report does not address Questions 1, 2, and 3

Navy Shipboard Hazardous Material Minimization Program

Energy Technology Data Exchange (ETDEWEB)

Bieberich, M.J. [Naval Surface Warfare Center, Annapolis, MD (United States). Carderock Div.; Robinson, P. [Life Cycle Engineering, Inc., Charleston, SC (United States); Chastain, B.

1994-12-31

The use of hazardous (and potentially hazardous) materials in shipboard cleaning applications has proliferated as new systems and equipments have entered the fleet to reside alongside existing equipments. With the growing environmental awareness (and additional, more restrictive regulations) at all levels/echelon commands of the DoD, the Navy has initiated a proactive program to undertake the minimization/elimination of these hazardous materials in order to eliminate HMs at the source. This paper will focus on the current Shipboard Hazardous Materials Minimization Program initiatives including the identification of authorized HM currently used onboard, identification of potential substitute materials for HM replacement, identification of new cleaning technologies and processes/procedures, and identification of technical documents which will require revision to eliminate the procurement of HMs into the federal supply system. Also discussed will be the anticipated path required to implement the changes into the fleet and automated decision processes (substitution algorithm) currently employed. The paper will also present the most recent technologies identified for approval or additional testing and analysis including: supercritical CO{sub 2} cleaning, high pressure blasting (H{sub 2}O + baking soda), aqueous and semi-aqueous cleaning materials and processes, solvent replacements and dedicated parts washing systems with internal filtering capabilities, automated software for solvent/cleaning process substitute selection. Along with these technological advances, data availability (from on-line databases and CDROM Database libraries) will be identified and discussed.

Hazard analysis in uranium hexafluoride production facility

International Nuclear Information System (INIS)

Marin, Maristhela Passoni de Araujo

1999-01-01

The present work provides a method for preliminary hazard analysis of nuclear fuel cycle facilities. The proposed method identify both chemical and radiological hazards, as well as the consequences associated with accident scenarios. To illustrate the application of the method, a uranium hexafluoride production facility was selected. The main hazards are identified and the potential consequences are quantified. It was found that, although the facility handles radioactive material, the main hazards as associated with releases of toxic chemical substances such as hydrogen fluoride, anhydrous ammonia and nitric acid. It was shown that a contention bung can effectively reduce the consequences of atmospheric release of toxic materials. (author)

Emergency preparedness hazards assessment for selected 100 Area Bechtel Hanford, Inc. facilities

International Nuclear Information System (INIS)

1997-07-01

The emergency preparedness hazards assessment for Bechtel Hanford Inc. (BHI) facilities in the 100 Areas of the Hanford Site. The purpose of a hazards assessment is to identify the hazardous material at each facility, identify the conditions that could release the hazardous material, and calculate the consequences of the releases. The hazards assessment is the technical basis for the facility emergency plans and procedures. There are many other buildings and past- practice burial grounds, trenches, cribs, etc., in the 100 Areas that may contain hazardous materials. Undisturbed buried waste sites that are not near the Columbia River are outside the scope of emergency preparedness hazards assessments because there is no mechanism for acute release to the air or ground water. The sites near the Columbia River are considered in a separate flood hazards assessment. This hazards assessment includes only the near-term soil remediation projects that involve intrusive activities

US Hazardous Materials Routes, Geographic WGS84, BTS (2006) [hazardous_material_routes_BTS_2006

Data.gov (United States)

Louisiana Geographic Information Center — The Federal Motor Carrier Safety Administration (FMCSA) Hazardous Material Routes were developed using the 2004 First Edition TIGER/Line files. The routes are...

Automating Risk Assessments of Hazardous Material Shipments for Transportation Routes and Mode Selection

International Nuclear Information System (INIS)

Dolphin, Barbara H.; Richins, William D.; Novascone, Stephen R.

2010-01-01

The METEOR project at Idaho National Laboratory (INL) successfully addresses the difficult problem in risk assessment analyses of combining the results from bounding deterministic simulation results with probabilistic (Monte Carlo) risk assessment techniques. This paper describes a software suite designed to perform sensitivity and cost/benefit analyses on selected transportation routes and vehicles to minimize risk associated with the shipment of hazardous materials. METEOR uses Monte Carlo techniques to estimate the probability of an accidental release of a hazardous substance along a proposed transportation route. A METEOR user selects the mode of transportation, origin and destination points, and charts the route using interactive graphics. Inputs to METEOR (many selections built in) include crash rates for the specific aircraft, soil/rock type and population densities over the proposed route, and bounding limits for potential accident types (velocity, temperature, etc.). New vehicle, materials, and location data are added when available. If the risk estimates are unacceptable, the risks associated with alternate transportation modes or routes can be quickly evaluated and compared. Systematic optimizing methods will provide the user with the route and vehicle selection identified with the lowest risk of hazardous material release. The effects of a selected range of potential accidents such as vehicle impact, fire, fuel explosions, excessive containment pressure, flooding, etc. are evaluated primarily using hydrocodes capable of accurately simulating the material response of critical containment components. Bounding conditions that represent credible accidents (i.e; for an impact event, velocity, orientations, and soil conditions) are used as input parameters to the hydrocode models yielding correlation functions relating accident parameters to component damage. The Monte Carlo algorithms use random number generators to make selections at the various decision

Incidents with hazardous radiation sources; Zwischenfaelle mit gefaehrlichen Strahlenquellen

Energy Technology Data Exchange (ETDEWEB)

Schoenhacker, Stefan [Bundesministerium fuer Inneres, Traiskirchen (Austria). Abt. 1/9 - Zivilschutzschule

2016-07-01

Incidents with hazardous radiation sources can occur in any country, even those without nuclear facilities. Preparedness for such incidents is supposed to fulfill globally agreed minimum standards. Incidents are categorized in incidents with licensed handling of radiation sources as for material testing, transport accidents of hazardous radiation sources, incidents with radionuclide batteries, incidents with satellites containing radioactive inventory, incidents wit not licensed handling of illegally acquired hazardous radiation sources. The emergency planning in Austria includes a differentiation according to the consequences: incidents with release of radioactive materials resulting in restricted contamination, incidents with release of radioactive materials resulting in local contamination, and incidents with the hazard of e@nhanced exposure due to the radiation source.

Training Materials for Release 3

DEFF Research Database (Denmark)

Wake, Jo Dugstad; Hansen, Cecilie; Debus, Kolja

This document, D7.4 – training materials for release 3, provides an overview of the training material for version 3 of the NEXT-TELL tools and methods. Previous documents submitted as part of work package 7, which is about teacher training, are D7.1 – Training Concept, D7.2 – Training Materials...... for Release 1 and D7.3 – Training Materials for Release 2. D7.4 builds on D7.1 and D7.2 and D7.3. D7.4 contains further development of previous work within WP7, essentially a revised theoretical approach to the teacher training, and expansion of the notion of tool training. The media in use have been expanded...

Analysis of hazardous substances released during CFRP laser processing

Science.gov (United States)

Hustedt, Michael; Walter, Juergen; Bluemel, Sven; Jaeschke, Peter; Kaierle, Stefan

2017-02-01

Due to their outstanding mechanical properties, in particular their high specific strength parallel to the carbon fibers, carbon fiber reinforced plastics (CFRP) have a high potential regarding resource-efficient lightweight construction. Consequently, these composite materials are increasingly finding application in important industrial branches such as aircraft, automotive and wind energy industry. However, the processing of these materials is highly demanding. On the one hand, mechanical processing methods such as milling or drilling are sometimes rather slow, and they are connected with notable tool wear. On the other hand, thermal processing methods are critical as the two components matrix and reinforcement have widely differing thermophysical properties, possibly leading to damages of the composite structure in terms of pores or delamination. An emerging innovative method for processing of CFRP materials is the laser technology. As principally thermal method, laser processing is connected with the release of potentially hazardous, gaseous and particulate substances. Detailed knowledge of these process emissions is the basis to ensure the protection of man and the environment, according to the existing legal regulations. This knowledge will help to realize adequate protective measures and thus strengthen the development of CFRP laser processing. In this work, selected measurement methods and results of the analysis of the exhaust air and the air at the workplace during different laser processes with CFRP materials are presented. The investigations have been performed in the course of different cooperative projects, funded by the German Federal Ministry of Education and Research (BMBF) in the course of the funding initiative "Photonic Processes and Tools for Resource-Efficient Lightweight Structures".

Surveillance of hazardous substances releases due to system interruptions, 2002.

Science.gov (United States)

Orr, Maureen F; Ruckart, Perri Zeitz

2007-04-11

The Hazardous Substances Emergency Events Surveillance (HSEES) system collected information on 9014 acute hazardous substance releases in 15 participating states in 2002. There were 3749 fixed-facility manufacturing events, of which 2100 involved "interruptions" to normal processing and 1649 "comparisons" that did not involve interruption. Equipment failure (69%) or intentional acts (20%) were the main root factor. Many events occurred in October and November in three states (Texas, Louisiana, and New Jersey), in three manufacturing industries (industrial and miscellaneous chemicals; petroleum refining; and plastics, synthetics, and resins). In interruption events, the substance categories most often released were mixtures, other inorganic substances, and volatile organic compounds and those most often causing injury were acids, chlorine, bases, and ammonia. Comparison events resulted in more acutely injured persons (408 versus 59) and more evacuees (11,318 versus 335) than interruption events and therefore may receive more public health attention. Because of the large number of interruption events, targeted prevention activities, including management of change procedures, lessons-learned implementation, process hazards analysis, and appropriate protection for workers could be economically advantageous and improve environmental quality. Efforts should focus on the identified areas of greater occurrence. The relationship of weather and equipment failure with interruption events needs further investigation.

Estimated airborne release of plutonium from Atomics International's Nuclear Materials Development Facility in the Santa Susana site, California, as a result of postulated damage from severe wind and earthquake hazard

International Nuclear Information System (INIS)

Mishima, J.; Ayer, J.E.

1981-09-01

The potential mass of airborne releases of plutonium (source term) that could result from wind and seismic damage is estimated for the Atomics International Company's Nuclear Materials Development Facility (NMDF) at the Santa Susana site in California. The postulated source terms will be useful as the basis for estimating the potential dose to the maximum exposed individual by inhalation and to the total population living within a prescribed radius of the site. The respirable fraction of airborne particles is thus the principal concern. The estimated source terms are based on the damage ratio, and the potential airborne releases if all enclosures suffer particular levels of damage. In an attempt to provide a realistic range of potential source terms that include most of the normal processing conditions, a best estimate bounded by upper and lower limits is provided. The range of source terms is calculated by combining a high best estimate and a low damage ratio, based on a fraction of enclosures suffering crush or perforation, with the airborne release from enclosures based upon an upper limit, average, and lower limit inventory of dispersible materials at risk. Two throughput levels are considered. The factors used to evaluate the fractional airborne release of materials and the exchange rates between enclosed and exterior atmospheres are discussed. The postulated damage and source terms are discussed for wind and earthquake hazard scenarios in order of their increasing severity

Hazardous materials package performance regulations

International Nuclear Information System (INIS)

Russell, N.A.; Glass, R.E.; McClure, J.D.; Finley, N.C.

1992-01-01

The hazardous materials (hazmat) packaging development and certification process is currently defined by two different regulatory philosophies, one based on specification packagings and the other based on performance standards. With specification packagings, a packaging is constructed according to an agreed set of design specifications. In contrast, performance standards do not specify the packaging design; they specify performance standards that a packaging design must be able to pass before it can be certified for transport. The packaging can be designed according to individual needs as long as it meets these performance standards. Performance standards have been used nationally and internationally for about 40 years to certify radioactive materials (RAM) packagings. It is reasonable to state that for RAM transport, performance specifications have maintained transport safety. A committee of United Nation's experts recommended the performance standard philosophy as the preferred regulation method for hazmat packaging. Performance standards for hazmat packagings smaller than 118 gallons have been adopted in 49CFR178. Packagings for materials that are classified as toxic-by-inhalation must comply with the performance standards by October 1, 1993, and packagings for all other classes of hazardous materials covered must comply by October 1, 1996. For packages containing bulk (in excess of 188 gallons) quantities of materials that are extremely toxic by inhalation, there currently are no performance requirements. This paper discusses a Hazmat Packaging Performance Evaluation (HPPE) project to look at the subset of bulk packagings that are larger than 2000 gallons. The objectives of this project are the evaluate current hazmat specification packagings and develop supporting documentation for determining performance requirements for packagings in excess of 2000 gallons that transport hazardous materials that have been classified as extremely toxic by inhalation (METBI)

Sustainable Materials Management: Non-Hazardous Materials and Waste Management Hierarchy

Science.gov (United States)

EPA developed the non-hazardous materials and waste management hierarchy in recognition that no single waste management approach is suitable for managing all materials and waste streams in all circumstances.

Reporting releases of hazardous substances under CERCLA and EPCRA

International Nuclear Information System (INIS)

Dailey, R.

1990-04-01

Several federal environmental laws requires that ''release of hazardous substances to the environment'' above certain threshold amounts -- Reportable Quantities or RQs -- be reported. Current and proposed regulations under these statutes are unclear and make full compliance difficult. Nevertheless, failure to comply could result in civil or criminal penalties. In response to questions raised by several DOE Field Elements, this Information Brief is part of a series that will provide updated information on this and other CERCLA issues. The Environmental Guidance Division (EH-231) has responded to those questions relating the reporting of releases for which EPA has a clearly articulated position. EPA's position on other questions raised by Field Elements has been equivocal; DOE is working with EPA to resolve these outstanding issues. Additional information briefs on reporting releases will be issued as a clear position is defined

Implications of the Differential Toxicological Effects of III-V Ionic and Particulate Materials for Hazard Assessment of Semiconductor Slurries.

Science.gov (United States)

Jiang, Wen; Lin, Sijie; Chang, Chong Hyun; Ji, Zhaoxia; Sun, Bingbing; Wang, Xiang; Li, Ruibin; Pon, Nanetta; Xia, Tian; Nel, André E

2015-12-22

Because of tunable band gaps, high carrier mobility, and low-energy consumption rates, III-V materials are attractive for use in semiconductor wafers. However, these wafers require chemical mechanical planarization (CMP) for polishing, which leads to the generation of large quantities of hazardous waste including particulate and ionic III-V debris. Although the toxic effects of micron-sized III-V materials have been studied in vivo, no comprehensive assessment has been undertaken to elucidate the hazardous effects of submicron particulates and released III-V ionic components. Since III-V materials may contribute disproportionately to the hazard of CMP slurries, we obtained GaP, InP, GaAs, and InAs as micron- (0.2-3 μm) and nanoscale (particles for comparative studies of their cytotoxic potential in macrophage (THP-1) and lung epithelial (BEAS-2B) cell lines. We found that nanosized III-V arsenides, including GaAs and InAs, could induce significantly more cytotoxicity over a 24-72 h observation period. In contrast, GaP and InP particulates of all sizes as well as ionic GaCl3 and InCl3 were substantially less hazardous. The principal mechanism of III-V arsenide nanoparticle toxicity is dissolution and shedding of toxic As(III) and, to a lesser extent, As(V) ions. GaAs dissolves in the cell culture medium as well as in acidifying intracellular compartments, while InAs dissolves (more slowly) inside cells. Chelation of released As by 2,3-dimercapto-1-propanesulfonic acid interfered in GaAs toxicity. Collectively, these results demonstrate that III-V arsenides, GaAs and InAs nanoparticles, contribute in a major way to the toxicity of III-V materials that could appear in slurries. This finding is of importance for considering how to deal with the hazard potential of CMP slurries.

Technology assessment of solar-energy systems. Materials resource and hazardous materials impacts of solar deployment

Science.gov (United States)

Schiffman, Y. M.; Tahami, J. E.

1982-04-01

The materials-resource and hazardous-materials impacts were determined by examining the type and quantity of materials used in the manufacture, construction, installation, operation and maintenance of solar systems. The materials requirements were compared with US materials supply and demand data to determine if potential problems exist in terms of future availability of domestic supply and increased dependence on foreign sources of supply. Hazardous materials were evaluated in terms of public and occupational health hazards and explosive and fire hazards. It is concluded that: although large amounts of materials would be required, the US had sufficient industrial capacity to produce those materials; (2) postulated growth in solar technology deployment during the period 1995-2000 could cause some production shortfalls in the steel and copper industry; the U.S. could increase its import reliance for certain materials such as silver, iron ore, and copper; however, shifts to other materials such as aluminum and polyvinylchloride could alleviate some of these problems.

Stochastic Modeling of Radioactive Material Releases

International Nuclear Information System (INIS)

Andrus, Jason; Pope, Chad

2015-01-01

Nonreactor nuclear facilities operated under the approval authority of the U.S. Department of Energy use unmitigated hazard evaluations to determine if potential radiological doses associated with design basis events challenge or exceed dose evaluation guidelines. Unmitigated design basis events that sufficiently challenge dose evaluation guidelines or exceed the guidelines for members of the public or workers, merit selection of safety structures, systems, or components or other controls to prevent or mitigate the hazard. Idaho State University, in collaboration with Idaho National Laboratory, has developed a portable and simple to use software application called SODA (Stochastic Objective Decision-Aide) that stochastically calculates the radiation dose associated with hypothetical radiological material release scenarios. Rather than producing a point estimate of the dose, SODA produces a dose distribution result to allow a deeper understanding of the dose potential. SODA allows users to select the distribution type and parameter values for all of the input variables used to perform the dose calculation. SODA then randomly samples each distribution input variable and calculates the overall resulting dose distribution. In cases where an input variable distribution is unknown, a traditional single point value can be used. SODA was developed using the MATLAB coding framework. The software application has a graphical user input. SODA can be installed on both Windows and Mac computers and does not require MATLAB to function. SODA provides improved risk understanding leading to better informed decision making associated with establishing nuclear facility material-at-risk limits and safety structure, system, or component selection. It is important to note that SODA does not replace or compete with codes such as MACCS or RSAC, rather it is viewed as an easy to use supplemental tool to help improve risk understanding and support better informed decisions. The work was

Stochastic Modeling of Radioactive Material Releases

Energy Technology Data Exchange (ETDEWEB)

Andrus, Jason [Idaho National Lab. (INL), Idaho Falls, ID (United States); Pope, Chad [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2015-09-01

Nonreactor nuclear facilities operated under the approval authority of the U.S. Department of Energy use unmitigated hazard evaluations to determine if potential radiological doses associated with design basis events challenge or exceed dose evaluation guidelines. Unmitigated design basis events that sufficiently challenge dose evaluation guidelines or exceed the guidelines for members of the public or workers, merit selection of safety structures, systems, or components or other controls to prevent or mitigate the hazard. Idaho State University, in collaboration with Idaho National Laboratory, has developed a portable and simple to use software application called SODA (Stochastic Objective Decision-Aide) that stochastically calculates the radiation dose associated with hypothetical radiological material release scenarios. Rather than producing a point estimate of the dose, SODA produces a dose distribution result to allow a deeper understanding of the dose potential. SODA allows users to select the distribution type and parameter values for all of the input variables used to perform the dose calculation. SODA then randomly samples each distribution input variable and calculates the overall resulting dose distribution. In cases where an input variable distribution is unknown, a traditional single point value can be used. SODA was developed using the MATLAB coding framework. The software application has a graphical user input. SODA can be installed on both Windows and Mac computers and does not require MATLAB to function. SODA provides improved risk understanding leading to better informed decision making associated with establishing nuclear facility material-at-risk limits and safety structure, system, or component selection. It is important to note that SODA does not replace or compete with codes such as MACCS or RSAC, rather it is viewed as an easy to use supplemental tool to help improve risk understanding and support better informed decisions. The work was

An optimization model for transportation of hazardous materials

International Nuclear Information System (INIS)

Seyed-Hosseini, M.; Kheirkhah, A. S.

2005-01-01

In this paper, the optimal routing problem for transportation of hazardous materials is studied. Routing for the purpose of reducing the risk of transportation of hazardous materials has been studied and formulated by many researcher and several routing models have been presented up to now. These models can be classified into the categories: the models for routing a single movement and the models for routing multiple movements. In this paper, according to the current rules and regulations of road transportations of hazardous materials in Iran, a routing problem is designed. In this problem, the routs for several independent movements are simultaneously determined. To examine the model, the problem the transportations of two different dangerous materials in the road network of Mazandaran province in the north of Iran is formulated and solved by applying Integer programming model

Investigating the presence of hazardous materials in buildings

International Nuclear Information System (INIS)

Gustitus, D.A.; Blaisdell, P.M.

1996-01-01

Environmental hazards in buildings can be found in the air, on exposed surfaces, or hidden in roofs, walls, and systems. They can exist in buildings in solid, liquid, and gaseous states. A sound methodology for investigating the presence of environmental hazards in buildings should include several components. The first step in planning an investigation of environmental hazards in buildings is to ascertain why the investigation is to be performed. Research should be performed to review available documentation on the building. Next, a visual inspection of the building should be performed to identify and document existing conditions, and all suspect materials containing environmental hazards. Lastly, samples of suspect materials should be collected for testing. It is important to sample appropriate materials, based on the information obtained during the previous steps of the investigation. It is also important to collect the samples using standard procedures. Pollutants of concern include asbestos, lead, PCBs, and radon

Generalized railway tank car safety design optimization for hazardous materials transport: Addressing the trade-off between transportation efficiency and safety

International Nuclear Information System (INIS)

Saat, Mohd Rapik; Barkan, Christopher P.L.

2011-01-01

North America railways offer safe and generally the most economical means of long distance transport of hazardous materials. Nevertheless, in the event of a train accident releases of these materials can pose substantial risk to human health, property or the environment. The majority of railway shipments of hazardous materials are in tank cars. Improving the safety design of these cars to make them more robust in accidents generally increases their weight thereby reducing their capacity and consequent transportation efficiency. This paper presents a generalized tank car safety design optimization model that addresses this tradeoff. The optimization model enables evaluation of each element of tank car safety design, independently and in combination with one another. We present the optimization model by identifying a set of Pareto-optimal solutions for a baseline tank car design in a bicriteria decision problem. This model provides a quantitative framework for a rational decision-making process involving tank car safety design enhancements to reduce the risk of transporting hazardous materials.

Hazardous-materials-management system: a guide for local emergency managers

International Nuclear Information System (INIS)

Lee, M.T.; Roe, P.G.

1981-07-01

An increase in the manufacture, storage, and transportation of hazardous materials is occurring across the nation. Local jurisdictions have realized that they have the responsibility to assure a reasonable level of safety to their community members and visitors alike. Such a responsibility can be met by developing methods of preventing hazardous materials incidents; enforcing laws related to transporting and storing hazardous materials; the initiating of an appropriate first response, and activating available resources of government agencies and commercial organizations that deal with containment and cleanup. This manual has been written to help in the development of a total Hazardous Material Management System. The manual describes one approach but allows for variations as may be appropriate for the specific jurisdiction

An advanced model for spreading and evaporation of accidentally released hazardous liquids on land

NARCIS (Netherlands)

Trijssenaar-Buhre, I.J.M.; Sterkenburg, R.P.; Wijnant-Timmerman, S.I.

2009-01-01

Pool evaporation modelling is an important element in consequence assessment of accidentally released hazardous liquids. The evaporation rate determines the amount of toxic or flammable gas released into the atmosphere and is an important factor for the size of a pool fire. In this paper a

An advanced model for spreading and evaporation of accidentally released hazardous liquids on land

NARCIS (Netherlands)

Trijssenaar-Buhre, I.J.M.; Wijnant-Timmerman, S.L.

2008-01-01

Pool evaporation modelling is an important element in consequence assessment of accidentally released hazardous liquids. The evaporation rate determines the amount of toxic or flammable gas released into the atmosphere and is an important factor for the size of a pool fire. In this paper a

49 CFR 173.33 - Hazardous materials in cargo tank motor vehicles.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Hazardous materials in cargo tank motor vehicles... Transportation § 173.33 Hazardous materials in cargo tank motor vehicles. (a) General requirements. (1) No person may offer or accept a hazardous material for transportation in a cargo tank motor vehicle except as...

Preventing method and device for underground permeation of hazardous material

International Nuclear Information System (INIS)

Funabashi, Kiyomi; Kurokawa, Hideaki; Fukazawa, Tetsuo; Yamazaki, Tadashi.

1996-01-01

In a method of preventing hazardous materials from permeating into ground by burying adsorbing materials underground, a plurality of adsorbing layers are laminated being spaced apart from each other, the concentration of the hazardous materials between each of the adsorbent layers is measured. When the concentration reaches a predetermined value, the adsorbent layers are regenerated. A suppression means for preventing hazardous materials from permeating into the ground are formed by an upper adsorbent layer and a lower adsorbent layer, and a means for measuring the concentration of hazardous materials passing through the upper adsorbent layer and a means for charging and discharging regenerated liquid are disposed. When it is detected that the poisonous materials can not be eliminated, the poisonous materials are already permeated to the adsorbent layer, and they start to inflow into underground water. In order to prevent it, an adsorbent layer is additionally disposed at the lower side of the place of detection to eliminate the poisonous materials completely thereby enabling to prevent poisonous materials from permeating into underground for a long period of time. (T.M.)

Instrumentation for Detecting Hazardous Materials.

Science.gov (United States)

1980-06-01

equipment a detector for monitoring radioactivity . A portable device for detecting the presence of hazardous mate- rials should also be included in the...Acrylonitrile 2 Natural Gas/LNG 2 211 ----- Material Name (Cont’d.) Number of Times Listed Radioactive Materials 2 Fertilizers 1 Cellulose Nitrate 1 Acrolein...Birnbaum, and Curtis Fincher, L "Fluorescence Determination of the Atmospheric Polutant NO2 in Impact of Lasers in Spectroscopy, Vol. 49 of Proceed

GGVS. Ordinance on road transport of hazardous materials, including the European agreement on international road transport of hazardous materials (ADR), in their wording. Annexes A and B. Ordinances regarding exceptions from GGVS and from the ordinance on rail transport of hazardous materials, GGVE. Reasons. Selected guidelines. List of materials. 6. rev. and enlarged ed.

International Nuclear Information System (INIS)

Ridder, K.

1990-01-01

The brochure contains the following texts: (1) Ordinance on road transport of hazardous materials (GGVS), including the European agreement on international road transport of hazardous materials (ADR), as of 1990: Skeleton ordinance, annexes A and B, reasons given for the first version, and for the first amendment in 1988, execution guidelines - RS 002 (guidelines for executing the ordinance on road transport of hazardous materials, with catalogue of penalties), guidelines for drawing up written instructions for the event of accidents - RS 006, guiding principles for the training of vehicle conductors; (2) ordinance regarding exceptions from the ordinance on road transport of hazardous materials; (3) ordinance regarding exceptions from the ordinance on rail transport of hazardous materials; (4) selected guidelines: Technical guidelines TR IBC K 001, TRS 003, TRS 004, TRS 005, TRS 006; (5) listing of materials and objects governed by the ordinance on hazardous materials transport; (6) catalogue of penalties relative to road transport of hazardous materials. (orig./HP) [de

Fluoride-releasing restorative materials and secondary caries.

Science.gov (United States)

Hicks, John; Garcia-Godoy, Franklin; Donly, Kevin; Flaitz, Catherine

2003-03-01

Secondary caries is responsible for 60 percent of all replacement restorations in the typical dental practice. Risk factors for secondary caries are similar to those for primary caries development. Unfortunately, it is not possible to accurately predict which patients are at risk for restoration failure. During the past several decades, fluoride-releasing dental materials have become a part of the dentist's armamentarium. Considerable fluoride is released during the setting reaction and for periods up to eight years following restoration placement. This released fluoride is readily taken up by the cavosurface tooth structure, as well as the enamel and root surfaces adjacent to the restoration. Resistance against caries along the cavosurface and the adjacent smooth surface has been shown in both in vitro and in vivo studies. Fluoride-releasing dental materials provide for improved resistance against primary and secondary caries in coronal and root surfaces. Plaque and salivary fluoride levels are elevated to a level that facilitates remineralization. In addition, the fluoride released to dental plaque adversely affects the growth of lactobacilli and mutans streptococci by interference with bacterial enzyme systems. Fluoride recharging of these dental materials is readily achieved with fluoridated toothpastes, fluoride mouthrinses, and other sources of topical fluoride. This allows fluoride-releasing dental materials to act as intraoral fluoride reservoirs. The improvement in the properties of dental materials with the ability to release fluoride has improved dramatically in the past decade, and it is anticipated that in the near future the vast majority of restorative procedures will employ fluoride-releasing dental materials as bonding agents, cavity liners, luting agents, adhesives for orthodontic brackets, and definitive restoratives.

Transportation of hazardous materials (hazmat a literature survey

Directory of Open Access Journals (Sweden)

Zafer YILMAZ

2016-02-01

Full Text Available ransportation has a great role in logistics. Many researchers have studied on transportation and vehicle routing problems. Transportation of hazardous materials (hazmat is a special subject for logistics. Causalities due to the accidents caused by trucks carrying hazardous materials will be intolerable. Many researchers have studied on risk assessment of hazmat transportation to find ways for reducing hazardous material transportation risks. Some researchers have studied routing of hazmat trucks. The emergency response models and network design problems for hazmat transportation were also studied by some researchers. The transportation of hazmats can also be classified according to the mode of transport. Mainly roads are used for hazmat transportation but some shipments are intermodal. There has been a great amount of effort spent to find convenient ways for hazmat transportation. In this study, a literature survey for the articles about hazmat transportation is prepared. After pointing out the importance of hazmat transportation by the example of US hazmat transportation data, the studies on hazmat transportation since 2005 have been examined. Totally 88 articles are classified as risk, routing, routing and scheduling, emergency response, network design and accident analysis. What can be studied in future researches is pointed out.Keywords: Hazardous materials, Network design, Transportation, Routing, Risk assessment

Auditors of safety in hazardous materials transportation

International Nuclear Information System (INIS)

Manas Lahoz, J.L.

1993-01-01

The author describes the methodology for safety auditory and control, prevention, risks of hazardous materials transport through ship, airplane, rail, etc. In this way, The author presents the classification of damage materials transport, characteristic damage and different transport methods

Hanford Site radioactive hazardous materials packaging directory

International Nuclear Information System (INIS)

McCarthy, T.L.

1995-12-01

The Hanford Site Radioactive Hazardous Materials Packaging Directory (RHMPD) provides information concerning packagings owned or routinely leased by Westinghouse Hanford Company (WHC) for offsite shipments or onsite transfers of hazardous materials. Specific information is provided for selected packagings including the following: general description; approval documents/specifications (Certificates of Compliance and Safety Analysis Reports for Packaging); technical information (drawing numbers and dimensions); approved contents; areas of operation; and general information. Packaging Operations ampersand Development (PO ampersand D) maintains the RHMPD and may be contacted for additional information or assistance in obtaining referenced documentation or assistance concerning packaging selection, availability, and usage

Hanford Site radioactive hazardous materials packaging directory

Energy Technology Data Exchange (ETDEWEB)

McCarthy, T.L.

1995-12-01

The Hanford Site Radioactive Hazardous Materials Packaging Directory (RHMPD) provides information concerning packagings owned or routinely leased by Westinghouse Hanford Company (WHC) for offsite shipments or onsite transfers of hazardous materials. Specific information is provided for selected packagings including the following: general description; approval documents/specifications (Certificates of Compliance and Safety Analysis Reports for Packaging); technical information (drawing numbers and dimensions); approved contents; areas of operation; and general information. Packaging Operations & Development (PO&D) maintains the RHMPD and may be contacted for additional information or assistance in obtaining referenced documentation or assistance concerning packaging selection, availability, and usage.

Risk methodologies for offsite hazardous materials

International Nuclear Information System (INIS)

Kot, C.A.; Eichler, T.V.; Wiedermann, A.H.

1983-01-01

A number of suggestions have been advanced in recent years concerning the risks posed to nuclear power plants by offsite hazardous materials relative to (1) the regulatory approach including considerations of minimum and safe standoff distances, exclusion distances, site acceptance ceilings and floors, screening distances and screening probabilities, plant design, etc., and (2) the analysis and evaluation procedures such as material screening criteria, plant vulnerability, standarized physical models, etc. An evaluation of current analyses and approaches indicates that this complex problem, variety of approaches, and safety concerns may be better accommodated by developing criteria and treatments along the lines of a so-called conditional risk approach. Specifically, the probability (P) of some ultimate consequence (C) occurring from an accident (A) involving hazardous materials is given as P(C) = P(C/A) x P(A). Assuming that the plant to accident site standoff distance is the fundamental independent variable of the risk methodology, certain conditional risk designations and conditions can be made and are presented

Regulatory Requirements to Combat Illicit Trafficking of Hazardous Materials

International Nuclear Information System (INIS)

Hussein, A.Z.; Zakaria, Kh.M.

2011-01-01

Since more than a decade illicit Trafficking of hazardous ( CBRNE), materials ( chemical, biological, radiological, nuclear and explosive ) has been identified as a key threat in national, regional, inter regional and international strategies. An Effective response to hazardous materials (CBRNE) risk and threat were realized to require a very high level of cooperation and coordination between various governments and their responsible organizations and authorities of regional and international partner. While improper policy of actions may easily be exploited by non- state members to (CBRNE) trafficking which may lead to develop weapon of mass destruction (WMD). Such strategy are of paramount important between all levels of the states and among regional agreements through comprehensive tailored assistance packages (e.g. export control, illicit trafficking of hazardous materials, redirection of scientist, emergency planning, crisis response safety and security culture. Capacity building, action plans and instruments for stability are necessary actions for efficient combating against illicit trafficking of hazardous materials. Regarding the needs of assessment phase, assistance must be based on data collection, analysis and prioritization of implanting the regulatory controls. Several activities have to be conducted to reduce CBRNE threat. The one- by- one approach, covering either nuclear and radioactive or chemical or biological materials has to be implanted on the country basis performance to mitigate CBRNE hazardous risk. On several consequent phases of intervention dealing with CBRNE risk mitigation the country has to establish a network of local, regional and international capabilities. Such network is setting up the mechanism for the country needs identifications, the guidelines for data collection, for data platform maintenance and update, the data assessment and the competent and operative organizations. This network will be to strengthen the long - term

75 FR 5261 - Waybill Data Reporting for Toxic Inhalation Hazards

Science.gov (United States)

2010-02-02

... monitor traffic flows and rate trends in the industry, and to develop evidence in Board proceedings. The... humans as to pose a hazard to health in the event of a release during transportation. These materials... so toxic to humans as to pose a hazard to health in the event of a release during transportation...

77 FR 60935 - Hazardous Materials: Minor Editorial Corrections and Clarifications (RRR)

Science.gov (United States)

2012-10-05

... flammable cryogenic liquid is not received by the consignee within 20 days from the date of shipment.... * * * * * Container ship * * * * * * * * Hazardous material means a substance or material that the Secretary of... transportation law (49 U.S.C. 5103). The term includes hazardous substances, hazardous wastes, marine pollutants...

Hazardous materials package performance regulations

International Nuclear Information System (INIS)

Russell, N.A.; Glass, R.E.; McClure, J.D.; Finley, N.C.

1993-01-01

Two regulatory philosophies, one based on 'specification' packaging standards and the other based on 'performance' packaging standards, currently define the hazmat packaging certification process. A main concern when setting performance standards is determining the appropriate standards necessary to assure adequate public protection. This paper discusses a Hazmat Packaging Performance Evaluation (HPPE) project being conducted at Sandia National Laboratories for the U.S. Department of Transportation Research and Special Programs Administration. In this project, the current bulk packagings (larger than 2000 gallons) for transporting Materials Extremely Toxic By Inhalation (METBI) are being evaluated and performance standards will be recommended. A computer software system, HazCon, has been developed which can calculate the dispersion of dense, neutral, and buoyant gases. HazCon also has a database of thermodynamic and toxicity data for the METBI materials, a user-friendly menu-driven format for creating input data sets for calculating dispersion of the METBI in the event of an accidental release, and a link between the METBI database and the dense gas dispersion code (which requires thermodynamic properties). The primary output of HazCon is a listing of mass concentrations of the released material at distances downwind from the release point. (J.P.N.)

Quality assurance for packaging of radioactive and hazardous materials

International Nuclear Information System (INIS)

Gustafson, L.D.

1986-01-01

The Department of Energy (DOE) has required for many years that quality assurance programs be established and implemented for the packaging of radioactive and hazardous materials. This paper identifies various requirement principles and related actions involved in establishing effective quality assurance for packaging of radioactive and hazardous materials. A primary purpose of these quality assurance program activities is to provide assurance that the packaging and transportation of hazardous materials, which includes radioactive and fissile materials, are in conformance with appropriate governmental regulations. Applicable regulations include those issued by the Nuclear Regulatory Commission (NRC), the Department of Transportation (DOT), and the Environmental Protection Agency (EPA). DOE Order 5700.6A establishes that quality assurance requirements are to be applied in accordance with national consensus standards where suitable ones are available. In the nuclear area, ANSI/ASME NQA-1 is the preferred standard

A proposal for a test method for assessment of hazard property HP 12 (“Release of an acute toxic gas”) in hazardous waste classification - Experience from 49 waste

OpenAIRE

Hennebert , Pierre; Samaali , Ismahen; Molina , Pauline

2016-01-01

International audience; A stepwise method for assessment of the HP 12 is proposed and tested with 49 waste samples. The hazard property HP 12 is defined as “Release of an acute toxic gas”: waste which releases acute toxic gases (Acute Tox. 1, 2 or 3) in contact with water or an acid. When a waste contains a substance assigned to one of the following supplemental hazards EUH029, EUH031 and EUH032, it shall be classified as hazardous by HP 12 according to test methods or guidelines (EC, 2014a, ...

78 FR 60755 - Hazardous Materials: Enhanced Enforcement Procedures-Resumption of Transportation

Science.gov (United States)

2013-10-02

... material,'' we envisioned etiological agents, such as biological products, infectious substances, medical... accidents or incidents involving the transportation of hazardous material. In order to achieve a uniform... DEPARTMENT OF TRANSPORTATION Pipeline and Hazardous Materials Safety Administration 49 CFR Part...

A new approach to hazardous materials transportation risk analysis: decision modeling to identify critical variables.

Science.gov (United States)

Clark, Renee M; Besterfield-Sacre, Mary E

2009-03-01

We take a novel approach to analyzing hazardous materials transportation risk in this research. Previous studies analyzed this risk from an operations research (OR) or quantitative risk assessment (QRA) perspective by minimizing or calculating risk along a transport route. Further, even though the majority of incidents occur when containers are unloaded, the research has not focused on transportation-related activities, including container loading and unloading. In this work, we developed a decision model of a hazardous materials release during unloading using actual data and an exploratory data modeling approach. Previous studies have had a theoretical perspective in terms of identifying and advancing the key variables related to this risk, and there has not been a focus on probability and statistics-based approaches for doing this. Our decision model empirically identifies the critical variables using an exploratory methodology for a large, highly categorical database involving latent class analysis (LCA), loglinear modeling, and Bayesian networking. Our model identified the most influential variables and countermeasures for two consequences of a hazmat incident, dollar loss and release quantity, and is one of the first models to do this. The most influential variables were found to be related to the failure of the container. In addition to analyzing hazmat risk, our methodology can be used to develop data-driven models for strategic decision making in other domains involving risk.

Program in change: shipment of hazardous materials at the INEL

International Nuclear Information System (INIS)

Reed, L.L.

1984-01-01

Positive measures such as education, control, and auditing ability should be incorporated into each hazardous material shipping program to assure compliance with regulations and the safe movement of hazardous materials. This paper discusses these and other pertinent components of a shipping program. 3 references

Environmentally sound management of hazardous waste and hazardous recyclable materials

International Nuclear Information System (INIS)

Smyth, T.

2002-01-01

Environmentally sound management or ESM has been defined under the Basel Convention as 'taking all practicable steps to ensure that hazardous wastes and other wastes are managed in a manner which will protect human health and the environment against the adverse effects which may result from such wastes'. An initiative is underway to develop and implement a Canadian Environmentally Sound Management (ESM) regime for both hazardous wastes and hazardous recyclable materials. This ESM regime aims to assure equivalent minimum environmental protection across Canada while respecting regional differences. Cooperation and coordination between the federal government, provinces and territories is essential to the development and implementation of ESM systems since waste management is a shared jurisdiction in Canada. Federally, CEPA 1999 provides an opportunity to improve Environment Canada's ability to ensure that all exports and imports are managed in an environmentally sound manner. CEPA 1999 enabled Environment Canada to establish criteria for environmentally sound management (ESM) that can be applied by importers and exporters in seeking to ensure that wastes and recyclable materials they import or export will be treated in an environmentally sound manner. The ESM regime would include the development of ESM principles, criteria and guidelines relevant to Canada and a procedure for evaluating ESM. It would be developed in full consultation with stakeholders. The timeline for the development and implementation of the ESM regime is anticipated by about 2006. (author)

Natural radioactivity and radiological hazards of building materials in Xianyang, China

International Nuclear Information System (INIS)

Lu Xinwei; Yang Guang; Ren Chunhui

2012-01-01

Common building materials collected from Xianyang, China were analyzed for the natural radioactivity of 226 Ra, 232 Th and 40 K using γ-ray spectroscopy. The average activity concentration of 226 Ra, 232 Th and 40 K in the studied building materials ranges from 13.4 to 69.9, 13.1–99.1 and 124.7–915.1 Bq kg −1 , respectively. The measured activity concentrations for these radionuclides were compared with the reported data of other countries and with the worldwide average activity of soil. To assess the radiation hazard of the natural radioactivity in all samples to the people, the radium equivalent activity, external hazard index, internal hazard index, indoor absorbed dose rate and total annual effective dose were estimated. The radium equivalent activities of the studied samples are below the internationally accepted values. The external hazard index and internal hazard index of all analyzed building materials are less than unity. The mean values of indoor absorbed dose rate for all building materials except for lime are higher than the world population-weighted average of 84 nGy h −1 and the total annual effective dose values of building materials are lower than 1 mSv y −1 except for some cyan brick samples. The study shows the measured building materials do not pose significant source of radiation hazard and are safe for use in the construction of dwellings. - Highlights: ► Natural radioactivity in building materials was determined by gamma ray spectrometry. ► The radiological hazard of studied building materials is within the recommended safety limit. ► Most of the studied building materials do not pose significant radiation risk to residents.

Unify a hazardous materials/waste program

International Nuclear Information System (INIS)

Carson, H.T.

1988-01-01

Efficiently managing a hazardous materials/waste program in a multi-facility, multi-product corporation is a major challenge. This paper describes several methods to help unify a program and gain maximum efficiency of manpower and to minimize risk

Stimuli-Responsive Materials for Controlled Release Applications

KAUST Repository

Li, Song

2015-04-01

The controlled release of therapeutics has been one of the major challenges for scientists and engineers during the past three decades. To address this outstanding problem, the design and fabrication of stimuli-responsive materials are pursued to guarantee the controlled release of cargo at a specific time and with an accurate amount. Upon applying different stimuli such as light, magnetic field, heat, pH change, enzymes or redox, functional materials change their physicochemical properties through physical transformation or chemical reactions, allowing the release of payload agents on demand. This dissertation studied three stimuli-responsive membrane systems for controlled release from films of macro sizes to microcapsules of nano sizes. The first membrane system is a polymeric composite film which can decrease and sustain diffusion upon light irradiation. The photo-response of membranes is based on the photoreaction of cinnamic derivatives. The second one is composite membrane which can improve diffusion upon heating. The thermo-response of membranes comes from the volume phase transition ability of hydrogels. The third one is microcapsule which can release encapsulated agents upon light irradiation. The photo-response of capsules results from the photoreaction of nitrobenzyl derivatives. The study on these membrane systems reveals that stimuli-responsive release can be achieved by utilizing different functional materials on either macro or micro level. Based on the abundant family of smart materials, designing and fabricating stimuli-responsive systems shall lead to various advanced release processes on demand for biomedical applications.

Hazardous Materials Management and Emergency Response (HAMMER)

Data.gov (United States)

Federal Laboratory Consortium — The Volpentest Hazardous Materials Management and Emergency Response (HAMMER) Federal Training Center is a safety and emergency response training center that offers...

REITP3-Hazard evaluation program for heat release based on thermochemical calculation

Energy Technology Data Exchange (ETDEWEB)

Akutsu, Yoshiaki.; Tamura, Masamitsu. [The University of Tokyo, Tokyo (Japan). School of Engineering; Kawakatsu, Yuichi. [Oji Paper Corp., Tokyo (Japan); Wada, Yuji. [National Institute for Resources and Environment, Tsukuba (Japan); Yoshida, Tadao. [Hosei University, Tokyo (Japan). College of Engineering

1999-06-30

REITP3-A hazard evaluation program for heat release besed on thermochemical calculation has been developed by modifying REITP2 (Revised Estimation of Incompatibility from Thermochemical Properties{sup 2)}. The main modifications are as follows. (1) Reactants are retrieved from the database by chemical formula. (2) As products are listed in an external file, the addition of products and change in order of production can be easily conducted. (3) Part of the program has been changed by considering its use on a personal computer or workstation. These modifications will promote the usefulness of the program for energy hazard evaluation. (author)

Advanced Manufacturing Processes Laboratory Building 878 hazards assessment document

Energy Technology Data Exchange (ETDEWEB)

Wood, C.; Thornton, W.; Swihart, A.; Gilman, T.

1994-07-01

The introduction of the hazards assessment process is to document the impact of the release of hazards at the Advanced Manufacturing Processes Laboratory (AMPL) that are significant enough to warrant consideration in Sandia National Laboratories` operational emergency management program. This hazards assessment is prepared in accordance with the Department of Energy Order 5500.3A requirement that facility-specific hazards assessments be prepared, maintained, and used for emergency planning purposes. This hazards assessment provides an analysis of the potential airborne release of chemicals associated with the operations and processes at the AMPL. This research and development laboratory develops advanced manufacturing technologies, practices, and unique equipment and provides the fabrication of prototype hardware to meet the needs of Sandia National Laboratories, Albuquerque, New Mexico (SNL/NM). The focus of the hazards assessment is the airborne release of materials because this requires the most rapid, coordinated emergency response on the part of the AMPL, SNL/NM, collocated facilities, and surrounding jurisdiction to protect workers, the public, and the environment.

Advanced Manufacturing Processes Laboratory Building 878 hazards assessment document

International Nuclear Information System (INIS)

Wood, C.; Thornton, W.; Swihart, A.; Gilman, T.

1994-07-01

The introduction of the hazards assessment process is to document the impact of the release of hazards at the Advanced Manufacturing Processes Laboratory (AMPL) that are significant enough to warrant consideration in Sandia National Laboratories' operational emergency management program. This hazards assessment is prepared in accordance with the Department of Energy Order 5500.3A requirement that facility-specific hazards assessments be prepared, maintained, and used for emergency planning purposes. This hazards assessment provides an analysis of the potential airborne release of chemicals associated with the operations and processes at the AMPL. This research and development laboratory develops advanced manufacturing technologies, practices, and unique equipment and provides the fabrication of prototype hardware to meet the needs of Sandia National Laboratories, Albuquerque, New Mexico (SNL/NM). The focus of the hazards assessment is the airborne release of materials because this requires the most rapid, coordinated emergency response on the part of the AMPL, SNL/NM, collocated facilities, and surrounding jurisdiction to protect workers, the public, and the environment

Risk management of onsite transportation of hazardous materials

International Nuclear Information System (INIS)

Wang, O.S.; Field, J.G.

1992-10-01

The US Department of Energy's (DOE) Hanford Site has recently undergone a significant change in its mission. The focus of site-wide operations has been shifted from production to environmental restoration. As a result, there is a significant increase in quantities of the radioactive wastes and other hazardous materials to be packaged and transported onsite. In response to the elevated transportation activities, the operations and engineering contractor for the Hanford Site, Westinghouse Hanford Company (Westinghouse Hanford), is proposing an integrated risk assessment methodology and risk management strategy to further enhance the safe operations of the onsite packaging and transportation activities involving radioactive and other hazardous materials. This paper summarizes Westinghouse Hanford's proposed risk assessment and risk management methodology for onsite transportation of hazardous materials. The proposed Westinghouse Hanford risk assessment and management methodology for onsite packaging and transportation has three integral parts: risk assessment, risk acceptance criteria, and risk minimization process. The purposes are to ensure that the risk for each ongoing transportation activity is acceptable, and to further reduce the overall risk for current and future onsite transportation activities

Regional risk associated with the transport of hazardous materials

OpenAIRE

Nardini, L.; Aparicio, L.; Bandoni, A.; Tonelli, S. M.

2003-01-01

An increasing concern over the level of risk associated with hazardous materials transportation has led international efforts to focus on risk assessment at regional level. Following this trend, the aim of this work is to review the latest procedures for analysing the regional risks resulting from hazardous materials transportation by means of road and rail. In particular, two methodologies are reviewed and discussed, a method recently developed at Swiss Federal Institute of Technology [1] an...

Toward a federal/state/local partnership in hazardous materials transportation safety

International Nuclear Information System (INIS)

1982-09-01

In recognition of the federal government's responsibility for initiating a national strategy for hazardous materials transportation safety, the Materials Transportation Bureau (MTB) prepared an internal strategy paper for creating a federal/state/local partnership in hazardous materials transportation safety in August 1981. The paper outlined the scope of the hazardous materials transportation problem and established MTB's approach for creating an intergovernmental partnership for its resolution. This paper represents an update and refinement of the original plan, and is designed to chart the direction of the emerging federal/state/local relationship. The cornerstone of the plan remains the establishment of a single national set of safety regulations. It is on achievement of this objective that MTB's plan for development of enforcement, training, and emergency response capabilities at all levels of government is based. Chapter I introduces the problem with a desription of the economic importance of hazardous materials and discusses its implications for public safety. Chapter II defines the appropriate role for each level of government in the areas of rulemaking, enforcement, emergency response, and education. Chapter III demonstrates the need for uniform national safety standards and describes the economic and safety benefits of this approach. Chapter IV contains a detailed description of MTB's program for developing a successful intergovernmental partnership in hazardous materials transportation safety

Environmental risk analysis of hazardous material rail transportation

Energy Technology Data Exchange (ETDEWEB)

Saat, Mohd Rapik, E-mail: mohdsaat@illinois.edu [Department of Civil and Environmental Engineering, University of Illinois at Urbana-Champaign, 1243 Newmark Civil Engineering Laboratory, 205 North Mathews Avenue, Urbana, IL 61801 (United States); Werth, Charles J.; Schaeffer, David [Department of Civil and Environmental Engineering, University of Illinois at Urbana-Champaign, 1243 Newmark Civil Engineering Laboratory, 205 North Mathews Avenue, Urbana, IL 61801 (United States); Yoon, Hongkyu [Sandia National Laboratories, Albuquerque, NM 87123 (United States); Barkan, Christopher P.L. [Department of Civil and Environmental Engineering, University of Illinois at Urbana-Champaign, 1243 Newmark Civil Engineering Laboratory, 205 North Mathews Avenue, Urbana, IL 61801 (United States)

2014-01-15

Highlights: • Comprehensive, nationwide risk assessment of hazardous material rail transportation. • Application of a novel environmental (i.e. soil and groundwater) consequence model. • Cleanup cost and total shipment distance are the most significant risk factors. • Annual risk varies from $20,000 to $560,000 for different products. • Provides information on the risk cost associated with specific product shipments. -- Abstract: An important aspect of railroad environmental risk management involves tank car transportation of hazardous materials. This paper describes a quantitative, environmental risk analysis of rail transportation of a group of light, non-aqueous-phase liquid (LNAPL) chemicals commonly transported by rail in North America. The Hazardous Materials Transportation Environmental Consequence Model (HMTECM) was used in conjunction with a geographic information system (GIS) analysis of environmental characteristics to develop probabilistic estimates of exposure to different spill scenarios along the North American rail network. The risk analysis incorporated the estimated clean-up cost developed using the HMTECM, route-specific probability distributions of soil type and depth to groundwater, annual traffic volume, railcar accident rate, and tank car safety features, to estimate the nationwide annual risk of transporting each product. The annual risk per car-mile (car-km) and per ton-mile (ton-km) was also calculated to enable comparison between chemicals and to provide information on the risk cost associated with shipments of these products. The analysis and the methodology provide a quantitative approach that will enable more effective management of the environmental risk of transporting hazardous materials.

Environmental risk analysis of hazardous material rail transportation

International Nuclear Information System (INIS)

Saat, Mohd Rapik; Werth, Charles J.; Schaeffer, David; Yoon, Hongkyu; Barkan, Christopher P.L.

2014-01-01

Highlights: • Comprehensive, nationwide risk assessment of hazardous material rail transportation. • Application of a novel environmental (i.e. soil and groundwater) consequence model. • Cleanup cost and total shipment distance are the most significant risk factors. • Annual risk varies from $20,000 to $560,000 for different products. • Provides information on the risk cost associated with specific product shipments. -- Abstract: An important aspect of railroad environmental risk management involves tank car transportation of hazardous materials. This paper describes a quantitative, environmental risk analysis of rail transportation of a group of light, non-aqueous-phase liquid (LNAPL) chemicals commonly transported by rail in North America. The Hazardous Materials Transportation Environmental Consequence Model (HMTECM) was used in conjunction with a geographic information system (GIS) analysis of environmental characteristics to develop probabilistic estimates of exposure to different spill scenarios along the North American rail network. The risk analysis incorporated the estimated clean-up cost developed using the HMTECM, route-specific probability distributions of soil type and depth to groundwater, annual traffic volume, railcar accident rate, and tank car safety features, to estimate the nationwide annual risk of transporting each product. The annual risk per car-mile (car-km) and per ton-mile (ton-km) was also calculated to enable comparison between chemicals and to provide information on the risk cost associated with shipments of these products. The analysis and the methodology provide a quantitative approach that will enable more effective management of the environmental risk of transporting hazardous materials

Hazardous materials sensing: An electrical metamaterial approach

Energy Technology Data Exchange (ETDEWEB)

Rawat, Vaishali; Kitture, Rohini [Department of Applied Physics, Defence Institute of Advanced Technology (DIAT), Girinagar, Pune 411025 (India); Kumari, Dimple [Department of Applied Chemistry, Defence Institute of Advanced Technology (DIAT), Girinagar, Pune 411025 (India); Rajesh, Harsh [Society for Applied Microwave Electronics Engineering and Research (SAMEER), IIT-Bombay Campus, Powai, Mumbai (India); Banerjee, Shaibal [Department of Applied Chemistry, Defence Institute of Advanced Technology (DIAT), Girinagar, Pune 411025 (India); Kale, S.N., E-mail: sangeetakale2004@gmail.com [Department of Applied Physics, Defence Institute of Advanced Technology (DIAT), Girinagar, Pune 411025 (India)

2016-10-01

Metamaterials are recently emerging materials exhibiting amazing properties such as extremely miniaturized antennas, waveguides, optical couplers, multiplexers and filters. Such structures also respond to the variation in their ambient conditions when exposed to toxic and hazardous materials, which are especially hazardous to human health. Through this manuscript, we document our studies on three different high energy materials; namely 2- bromo-2nitropropane-1,3-diol (BNP), bis (1,3-diazido prop-2-yl) malonate (AM) and bis (1,3-diazido prop-2-yl) glutarate (AG). A Complementary Split Ring Resonator has been fabricated at resonant frequency of 4.48 GHz using copper on FR4 substrate. The energetic materials were exposed to the sensor and results were monitored using Vector Network Analyzer. The volume of liquids was varied from 0.5 µL to 3 µL. Prominent and explicit shifts in the transmission resonant frequency and amplitude was seen as a signature of each energetic material. The signatures were not only sensitive to the specific toxic group in the material but also to the volume of the liquid subjected to this sensor. The results are correlated with the simulation results, basic chemistry of the materials and permittivity measurements. The ultra-fast reversibility and repeatability, with good sensitivity and specificity of these devices project their applications in sensitive locations, particularly to combat for human security and health issues.

Improving the design of higher-capacity railway tank cars for hazardous materials transport: Optimizing the trade-off between weight and safety

International Nuclear Information System (INIS)

Barkan, Christopher P.L.

2008-01-01

As with many aspects of modern industrial society, decision-makers face trade-offs in considering hazardous materials transportation equipment and practices. Tank cars used for transport of hazardous materials can be made more resistant to damage in accidents through use of a thicker steel tank and other protective features. However, the additional weight of these features reduces the car's capacity and thus its efficiency as a transportation vehicle. In this paper the problem of tank car safety versus weight is developed as a multi-attribute decision problem. North American railroads recently developed specifications for higher capacity tank cars for transportation of hazardous materials including enhanced safety design features. A group of tank car safety design features or 'risk reduction options' (RROs) were analyzed with regard to their effect on the conditional probability of release in an accident, and their incremental effect on tank car weight. All possible combinations of these RROs were then analyzed in terms of the reduced release probability per unit of weight increase and the Pareto optimal set of options identified. This set included the combinations of RROs that provided the greatest improvement in safety with the least amount of additional weight for any desired level of tank car weight increase. The analysis was conducted for both non-insulated and insulated tank cars and used two objective functions, minimization of conditional probability of release, and minimization of expected quantity lost, given that a car was derailed in an accident. Sensitivity analyses of the effect of tank car size and use of different objective functions were conducted and the optimality results were found to be robust. The results of this analysis were used by the Association of American Railroads Tank Car Committee to develop new specifications for higher capacity non-insulated and insulated, non-pressure tank cars resulting in an estimated 32% and 24% respective

New Class of Hybrid Materials for Detection, Capture, and "On-Demand" Release of Carbon Monoxide.

Science.gov (United States)

Pitto-Barry, Anaïs; Lupan, Alexandru; Ellingford, Christopher; Attia, Amr A A; Barry, Nicolas P E

2018-04-25

Carbon monoxide (CO) is both a substance hazardous to health and a side product of a number of industrial processes, such as methanol steam reforming and large-scale oxidation reactions. The separation of CO from nitrogen (N 2 ) in industrial processes is considered to be difficult because of the similarities of their electronic structures, sizes, and physicochemical properties (e.g., boiling points). Carbon monoxide is also a major poison in fuel cells because of its adsorption onto the active sites of the catalysts. It is therefore of the utmost economic importance to discover new materials that enable effective CO capture and release under mild conditions. However, methods to specifically absorb and easily release CO in the presence of contaminants, such as water, nitrogen, carbon dioxide, and oxygen, at ambient temperature are not available. Here, we report the simple and versatile fabrication of a new class of hybrid materials that allows capture and release of carbon monoxide under mild conditions. We found that carborane-containing metal complexes encapsulated in networks made of poly(dimethylsiloxane) react with CO, even when immersed in water, leading to dramatic color and infrared signature changes. Furthermore, we found that the CO can be easily released from the materials by simply dipping the networks into an organic solvent for less than 1 min, at ambient temperature and pressure, which not only offers a straightforward recycling method, but also a new method for the "on-demand" release of carbon monoxide. We illustrated the utilization of the on-demand release of CO from the networks by carrying out a carbonylation reaction on an electron-deficient metal complex that led to the formation of the CO-adduct, with concomitant recycling of the gel. We anticipate that our sponge-like materials and scalable methodology will open up new avenues for the storage, transport, and controlled release of CO, the silent killer and a major industrial poison.

49 CFR 172.202 - Description of hazardous material on shipping papers.

Science.gov (United States)

2010-10-01

... papers. 172.202 Section 172.202 Transportation Other Regulations Relating to Transportation PIPELINE AND... INFORMATION, TRAINING REQUIREMENTS, AND SECURITY PLANS Shipping Papers § 172.202 Description of hazardous material on shipping papers. (a) The shipping description of a hazardous material on the shipping paper...

Screening tests for hazard classification of complex waste materials – Selection of methods

International Nuclear Information System (INIS)

Weltens, R.; Vanermen, G.; Tirez, K.; Robbens, J.; Deprez, K.; Michiels, L.

2012-01-01

In this study we describe the development of an alternative methodology for hazard characterization of waste materials. Such an alternative methodology for hazard assessment of complex waste materials is urgently needed, because the lack of a validated instrument leads to arbitrary hazard classification of such complex waste materials. False classification can lead to human and environmental health risks and also has important financial consequences for the waste owner. The Hazardous Waste Directive (HWD) describes the methodology for hazard classification of waste materials. For mirror entries the HWD classification is based upon the hazardous properties (H1–15) of the waste which can be assessed from the hazardous properties of individual identified waste compounds or – if not all compounds are identified – from test results of hazard assessment tests performed on the waste material itself. For the latter the HWD recommends toxicity tests that were initially designed for risk assessment of chemicals in consumer products (pharmaceuticals, cosmetics, biocides, food, etc.). These tests (often using mammals) are not designed nor suitable for the hazard characterization of waste materials. With the present study we want to contribute to the development of an alternative and transparent test strategy for hazard assessment of complex wastes that is in line with the HWD principles for waste classification. It is necessary to cope with this important shortcoming in hazardous waste classification and to demonstrate that alternative methods are available that can be used for hazard assessment of waste materials. Next, by describing the pros and cons of the available methods, and by identifying the needs for additional or further development of test methods, we hope to stimulate research efforts and development in this direction. In this paper we describe promising techniques and argument on the test selection for the pilot study that we have performed on different

Hydrothermal Liquefaction Treatment Preliminary Hazard Analysis Report

Energy Technology Data Exchange (ETDEWEB)

Lowry, Peter P.; Wagner, Katie A.

2015-08-31

A preliminary hazard assessment was completed during February 2015 to evaluate the conceptual design of the modular hydrothermal liquefaction treatment system. The hazard assessment was performed in 2 stages. An initial assessment utilizing Hazard Identification and Preliminary Hazards Analysis (PHA) techniques identified areas with significant or unique hazards (process safety-related hazards) that fall outside of the normal operating envelope of PNNL and warranted additional analysis. The subsequent assessment was based on a qualitative What-If analysis. This analysis was augmented, as necessary, by additional quantitative analysis for scenarios involving a release of hazardous material or energy with the potential for affecting the public.

The environmental and medical geochemistry of potentially hazardous materials produced by disasters

Science.gov (United States)

Plumlee, Geoffrey S.; Morman, Suzette A.; Meeker, G.P.; Hoefen, Todd M.; Hageman, Philip L.; Wolf, Ruth E.

2014-01-01

Many natural or human-caused disasters release potentially hazardous materials (HM) that may pose threats to the environment and health of exposed humans, wildlife, and livestock. This chapter summarizes the environmentally and toxicologically significant physical, mineralogical, and geochemical characteristics of materials produced by a wide variety of recent disasters, such as volcanic eruptions, hurricanes and extreme storms, spills of mining/mineral-processing wastes or coal extraction by-products, and the 2001 attacks on and collapse of the World Trade Center towers. In describing these characteristics, this chapter also illustrates the important roles that geochemists and other earth scientists can play in environmental disaster response and preparedness. In addition to characterizing in detail the physical, chemical, and microbial makeup of HM generated by the disasters, these roles also include (1) identifying and discriminating potential multiple sources of the materials; (2) monitoring, mapping, and modeling dispersal and evolution of the materials in the environment; (3) understanding how the materials are modified by environmental processes; (4) identifying key characteristics and processes that influence the materials' toxicity to exposed humans and ecosystems; (5) estimating shifts away from predisaster environmental baseline conditions; and (6) using geochemical insights learned from past disasters to help estimate, prepare for, and increase societal resilience to the environmental and related health impacts of future disasters.

A review of accidents, prevention and mitigation options related to hazardous gases

International Nuclear Information System (INIS)

Fthenakis, V.M.

1993-05-01

Statistics on industrial accidents are incomplete due to lack of specific criteria on what constitutes a release or accident. In this country, most major industrial accidents were related to explosions and fires of flammable materials, not to releases of chemicals into the environment. The EPA in a study of 6,928 accidental releases of toxic chemicals revealed that accidents at stationary facilities accounted for 75% of the total number of releases, and transportation accidents for the other 25%. About 7% of all reported accidents (468 cases) resulted in 138 deaths and 4,717 injuries ranging from temporary respiratory problems to critical injuries. In-plant accidents accounted for 65% of the casualties. The most efficient strategy to reduce hazards is to choose technologies which do not require the use of large quantities of hazardous gases. For new technologies this approach can be implemented early in development, before large financial resources and efforts are committed to specific options. Once specific materials and options have been selected, strategies to prevent accident initiating events need to be evaluated and implemented. The next step is to implement safety options which suppress a hazard when an accident initiating event occurs. Releases can be prevented or reduced with fail-safe equipment and valves, adequate warning systems and controls to reduce and interrupt gas leakage. If an accident occurs and safety systems fail to contain a hazardous gas release, then engineering control systems will be relied on to reduce/minimize environmental releases. As a final defensive barrier, the prevention of human exposure is needed if a hazardous gas is released, in spite of previous strategies. Prevention of consequences forms the final defensive barrier. Medical facilities close by that can accommodate victims of the worst accident can reduce the consequences of personnel exposure to hazardous gases

Assessment of radioactive material released from a fuel fabrication plant under accidental conditions

International Nuclear Information System (INIS)

1981-01-01

This report evaluates the amounts of fissile material released both inside and outside a mixed oxide fuel fabrication plant (MOFFP) for light water reactors. The first section begins with a descriptive study of fissile material containment systems, and the methods available for quantifying accident occurrence probabilities. In addition to accidents common to all industrial facilities, other much rarer accidents were considered, such as aircraft crashes. The minimum occurrence probability limit for consideration in this study was set at 10 -6 per annum. The second part of this report attempts to assess the consequences of the accidents considered (i.e. with occurrence probabilities exceeding 10 -6 per annum) by determining maximum values for such accidents. Acts of sabotage and other accidents of this type are beyond the scope of this study and were not taken into consideration. The most serious potential accident would be a fire involving all of the glove boxes in the PuO 2 powder calcination and preparation cell, which could release 76.5 mg of PuO 2 powder into the atmosphere; the occurrence probability of such an accident, however, is slight (less than 10 -5 per annum). The second possibility, is a specially nuclear hazard that would release fission products into the atmosphere. The occurrence probability of such an accident is currently evaluated at 10 -3 per annum

Chemical Hazards and Safety Issues in Fusion Safety Design

International Nuclear Information System (INIS)

Cadwallader, L.C.

2003-01-01

Radiological inventory releases have dominated accident consequences for fusion; these consequences are important to analyze and are generally the most severe result of a fusion facility accident event. However, the advent of, or plan for, large-scale usage of some toxic materials poses the additional hazard of chemical exposure from an accident event. Examples of toxic chemicals are beryllium for magnetic fusion and fluorine for laser fusion. Therefore, chemical exposure consequences must also be addressed in fusion safety assessment. This paper provides guidance for fusion safety analysis. US Department of Energy (DOE) chemical safety assessment practices for workers and the public are reviewed. The US Environmental Protection Agency (EPA) has published some guidance on public exposure to releases of mixtures of chemicals, this guidance has been used to create an initial guideline for treating mixed radiological and toxicological releases in fusion; for example, tritiated hazardous dust from a tokamak vacuum vessel. There is no convenient means to judge the hazard severity of exposure to mixed materials. The chemical fate of mixed material constituents must be reviewed to determine if there is a separate or combined radiological and toxicological carcinogenesis, or if other health threats exist with radiological carcinogenesis. Recommendations are made for fusion facility chemical safety evaluation and safety guidance for protecting the public from chemical releases, since such levels are not specifically identified in the DOE fusion safety standard

Hazardous materials management and compliance training

International Nuclear Information System (INIS)

Dalton, T.F.

1991-01-01

OSHA training for hazardous waste site workers is required by the Superfund Amendments and Reauthorization Act of 1986 (SARA). In December 1986, a series of regulations was promulgated by OSHA on an interim basis calling for the training of workers engaged in hazardous waste operations. Subsequent to these interim regulations, final rules were promulgated and these final rules on hazardous waste operations and emergency response became effective on March 6, 1990. OSHA has conducted hearings on the accreditation of training programs. OSHA would like to follow the accreditation process under the AHERA regulations for asbestos, in which the model plan for accreditation of asbestos abatement training was included in Section 206 of Title 11 of the Toxic Substance Control Act (TSCA). OSHA proposed on January 26, 1990, to perform the accreditation of training programs for hazardous waste operations and that proposal suggested that they follow the model plan similar to the one used for AHERA. They did not propose to accredited training programs for workers engaged in emergency response. These new regulations pose a significant problem to the various contractors and emergency responders who deal with hazardous materials spill response, cleanup and site remediation since these programs have expanded so quickly that many people are not familiar with what particular segment of the training they are required to have and whether or not programs that have yet to be accredited are satisfactory for this type of training. Title III of SARA stipulates a training program for first responders which includes local emergency response organizations such as firemen and policemen. The purpose of this paper is to discuss the needs of workers at hazardous waste site remediation projects and workers who are dealing with hazardous substances, spill response and cleanup

Hazardous materials transportation and emergency response programs

International Nuclear Information System (INIS)

Joy, D.S.; Fore, C.S.

1983-01-01

This presentation consists of the following visual aids; (1) detailed routing capabilities of truck, rail, barge; (2) legislative data base for hazardous materials; and (3) emergency response of accident site Eddyville, Kentucky (airports in vicinity of Eddyville, KY)

Nanostructured Diclofenac Sodium Releasing Material

Science.gov (United States)

Nikkola, L.; Vapalahti, K.; Harlin, A.; Seppälä, J.; Ashammakhi, N.

2008-02-01

Various techniques have been developed to produce second generation biomaterials for tissue repair. These include extrusion, molding, salt leaching, spinning etc, but success in regenerating tissues has been limited. It is important to develop porous material, yet with a fibrous structure for it to be biomimetic. To mimic biological tissues, the extra-cellular matrix usually contains fibers in nano scale. To produce nanostructures, self-assembly or electrospinning can be used. Adding a drug release function to such a material may advance applications further for use in controlled tissue repair. This turns the resulting device into a multifunctional porous, fibrous structure to support cells and drug releasing properties in order to control tissue reactions. A bioabsorbable poly(ɛ-caprolactone-co-D,L lactide) 95/5 (PCL) was made into diluted solution using a solvent, to which was added 2w-% of diclofenac sodium (DS). Nano-fibers were made by electrospinning onto substrate. Microstructure of the resulting nanomat was studied using SEM and drug release profiles with UV/VIS spectroscopy. Thickness of the electrospun nanomat was about 2 mm. SEM analysis showed that polymeric nano-fibers containing drug particles form a highly interconnected porous nano structure. Average diameter of the nano-fibers was 130 nm. There was a high burst peak in drug release, which decreased to low levels after one day. The used polymer has slow a degradation rate and though the nanomat was highly porous with a large surface area, drug release rate is slow. It is feasible to develop a nano-fibrous porous structure of bioabsorbable polymer, which is loaded with test drug. Drug release is targeted at improving the properties of biomaterial for use in controlled tissue repair and regeneration.

Automated accountability of hazardous materials at AlliedSignal Inc., Kansas City Division

International Nuclear Information System (INIS)

Depew, P.L.

1993-12-01

The Department of Energy's (DOE) Kansas City Plant (KCP), currently operated by AlliedSignal Inc. has developed a comprehensive Hazardous Material Information System (HMIS). The purpose of this system is to provide a practical and automated method to collect, analyze and distribute hazardous material information to DOE, KCP associates, and regulatory agencies. The drivers of the HMIS are compliance with OSHA Hazard Communications, SARA reporting, pollution prevention, waste minimization, control and tracking of hazards, and emergency response. This report provides a discussion of this system

Evaluation of Hazardous Material Management Safety in the Chemical Laboratory in BATAN

International Nuclear Information System (INIS)

Nur-Rahmah-Hidayati

2005-01-01

The management safety of the hazardous material (B3) in the chemical laboratory of BATAN was evaluated. The evaluation is necessary to be done because B3 is often used together with radioactive materials in the laboratory, but the attention to the safety aspect of B3 is not paid sufficiently in spite of its big potential hazard. The potential hazard generated from the nature of B3 could be flammable, explosive, oxidative, corrosive and poisonous. The handling of B3 could be conducted by enforcing the labelling and classification in the usage and disposal processes. Some observations of the chemical laboratory of BATAN show that the management safety of hazardous material in compliance with the government regulation no. 74 year 2001 has not been dully conducted. The management safety of B3 could be improved by, designating one who has adequate skill in hazardous material safety specially as the B3 safety officer, providing the Material Safety Data Sheet that is updated periodically to use in the laboratory and storage room, updating periodically the inventory of B3, performing training in work safety periodically, and monitoring the ventilation system intensively in laboratory and storage room. (author)

Sandia National Laboratories, California Hazardous Materials Management Program annual report.

Energy Technology Data Exchange (ETDEWEB)

Brynildson, Mark E.

2011-02-01

The annual program report provides detailed information about all aspects of the Sandia National Laboratories, California (SNL/CA) Hazardous Materials Management Program. It functions as supporting documentation to the SNL/CA Environmental Management System Program Manual. This program annual report describes the activities undertaken during the calender past year, and activities planned in future years to implement the Hazardous Materials Management Program, one of six programs that supports environmental management at SNL/CA.

Determination of Radiological, Material and Organizational Measures for Reuse of Conditionally Released Materials from Decommissioning

International Nuclear Information System (INIS)

Ondra, F.; Vasko, M.; Necas, V.

2012-01-01

An important part of nuclear installation decommissioning is conditional release of materials. The mass of conditionally released materials can significantly influence radioactive waste management and capacity of radioactive waste repository. The influence on a total decommissioning cost is also not negligible. Several scenarios for reuse of conditionally released materials were developed within CONRELMAT project. Each scenario contains preparation phase, construction phase and operation phase. For each above mentioned phase is needed to determine radiological, material, organizational and other constraints for conditionally released materials reuse to not break exposure limits for staff and public. Constraints are determined on the basis of external and internal exposure calculations in created models for selected takes in particular scenarios phases. The paper presents a developed methodology for determination of part of above mentioned constraints concerning external exposure of staff or public. Values of staff external exposure are also presented in paper to ensure that staff or public exposure does not break the limits. The methodology comprises a proposal of following constraints: radionuclide limit concentration of conditionally released materials for specific scenarios and nuclide vectors, specific deployment of conditionally released materials eventually shielding materials, staff and public during the scenario's phases, organizational measures concerning time of staff's or public's stay in the vicinity of conditionally released materials for individual performed scenarios and nuclide vectors. The paper further describes VISIPLAN 3D ALARA calculation planning software tool used for calculation of staff's and public's external exposure for individual scenarios. Several other parallel papers proposed for HND2012 are presenting selected details of the project.(author).

Hydrotreater/Distillation Column Hazard Analysis Report Rev. 2

Energy Technology Data Exchange (ETDEWEB)

Lowry, Peter P. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wagner, Katie A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2016-04-15

This project Hazard and Risk Analysis Report contains the results of several hazard analyses and risk assessments. An initial assessment was conducted in 2012, which included a multi-step approach ranging from design reviews to a formal What-If hazard analysis. A second What-If hazard analysis was completed during February 2013 to evaluate the operation of the hydrotreater/distillation column processes to be installed in a process enclosure within the Process Development Laboratory West (PDL-West) facility located on the PNNL campus. The qualitative analysis included participation of project and operations personnel and applicable subject matter experts. The analysis identified potential hazardous scenarios, each based on an initiating event coupled with a postulated upset condition. The unmitigated consequences of each hazardous scenario were generally characterized as a process upset; the exposure of personnel to steam, vapors or hazardous material; a spray or spill of hazardous material; the creation of a flammable atmosphere; or an energetic release from a pressure boundary.

Hazardous materials management and control program at Oak Ridge National Laboratory - environmental protection

International Nuclear Information System (INIS)

Eisenhower, B.M.; Oakes, T.W.

1982-01-01

In the Federal Register of May 19, 1980, the US Environmental Protection Agency promulgated final hazardous waste regulations according to the Resource Conservation and Recovery Act (RCRA) of 1976. The major substantive portions of these regulations went into effect on November 19, 1980, and established a federal program to provide comprehensive regulation of hazardous waste from its generation to its disposal. In an effort to comply with these regulations, a Hazardous Materials Management and Control Program was established at Oak Ridge National Laboratory. The program is administered by two Hazardous Materials Coordinators, who together with various support groups, ensure that all hazardous materials and wastes are handled in such a manner that all personnel, the general public, and the environment are adequately protected

14 CFR Appendix I to Part 417 - Methodologies for Toxic Release Hazard Analysis and Operational Procedures

Science.gov (United States)

2010-01-01

... Quotient/Hazard Index (HQ/HI) formulation to determine the toxic concentration threshold for mixtures of... cloud center of mass altitude. (vi) Worst case initial source term assuming instantaneous release of...

Transportation of hazardous materials in Iran: A strategic approach for decreasing accidents

Directory of Open Access Journals (Sweden)

S. Ghazinoory

2008-06-01

Full Text Available .“Hazardous materials” refer to those substances that seriously endanger human lives and/or the environment. The transportation of these materials will be inevitable in the increasingly industrialized economy of Iran. Nonetheless, numerous deadly accidents caused by the movement of these materials necessitate the design and implementation of preventive plans on several levels. This article looks into the present condition of transportation of hazardous materials in Iran and the resulting accidents. Optimal condition for the general transportation system of hazardous materials is delineated with due focus on transportation risk as the main parameter. Strategies for reaching the optimal condition are laid out and the impacts of these strategies on the reduction of accidents are analyzed.

Methodology for prediction and estimation of consequences of possible atmospheric releases of hazardous matter: 'Kursk' submarine study

Directory of Open Access Journals (Sweden)

A. Baklanov

2003-01-01

Full Text Available There are objects with some periods of higher than normal levels of risk of accidental atmospheric releases (nuclear, chemical, biological, etc.. Such accidents or events may occur due to natural hazards, human errors, terror acts, and during transportation of waste or various operations at high risk. A methodology for risk assessment is suggested and it includes two approaches: 1 probabilistic analysis of possible atmospheric transport patterns using long-term trajectory and dispersion modelling, and 2 forecast and evaluation of possible contamination and consequences for the environment and population using operational dispersion modelling. The first approach could be applied during the preparation stage, and the second - during the operation stage. The suggested methodology is applied on an example of the most important phases (lifting, transportation, and decommissioning of the ``Kursk" nuclear submarine operation. It is found that the temporal variability of several probabilistic indicators (fast transport probability fields, maximum reaching distance, maximum possible impact zone, and average integral concentration of 137Cs showed that the fall of 2001 was the most appropriate time for the beginning of the operation. These indicators allowed to identify the hypothetically impacted geographical regions and territories. In cases of atmospheric transport toward the most populated areas, the forecasts of possible consequences during phases of the high and medium potential risk levels based on a unit hypothetical release (e.g. 1 Bq are performed. The analysis showed that the possible deposition fractions of 10-11 (Bq/m2 over the Kola Peninsula, and 10-12 - 10-13 (Bq/m2 for the remote areas of the Scandinavia and Northwest Russia could be observed. The suggested methodology may be used successfully for any potentially dangerous object involving risk of atmospheric release of hazardous materials of nuclear, chemical or biological nature.

Methodology for prediction and estimation of consequences of possible atmospheric releases of hazardous matter: "Kursk"? submarine study

Science.gov (United States)

Baklanov, A.; Mahura, A.; Sørensen, J. H.

2003-03-01

There are objects with some periods of higher than normal levels of risk of accidental atmospheric releases (nuclear, chemical, biological, etc.). Such accidents or events may occur due to natural hazards, human errors, terror acts, and during transportation of waste or various operations at high risk. A methodology for risk assessment is suggested and it includes two approaches: 1) probabilistic analysis of possible atmospheric transport patterns using long-term trajectory and dispersion modelling, and 2) forecast and evaluation of possible contamination and consequences for the environment and population using operational dispersion modelling. The first approach could be applied during the preparation stage, and the second - during the operation stage. The suggested methodology is applied on an example of the most important phases (lifting, transportation, and decommissioning) of the "Kursk" nuclear submarine operation. It is found that the temporal variability of several probabilistic indicators (fast transport probability fields, maximum reaching distance, maximum possible impact zone, and average integral concentration of 137Cs) showed that the fall of 2001 was the most appropriate time for the beginning of the operation. These indicators allowed to identify the hypothetically impacted geographical regions and territories. In cases of atmospheric transport toward the most populated areas, the forecasts of possible consequences during phases of the high and medium potential risk levels based on a unit hypothetical release are performed. The analysis showed that the possible deposition fractions of 1011 over the Kola Peninsula, and 10-12 - 10-13 for the remote areas of the Scandinavia and Northwest Russia could be observed. The suggested methodology may be used successfully for any potentially dangerous object involving risk of atmospheric release of hazardous materials of nuclear, chemical or biological nature.

Methodology for prediction and estimation of consequences of possible atmospheric releases of hazardous matter: "Kursk" submarine study

Science.gov (United States)

Baklanov, A.; Mahura, A.; Sørensen, J. H.

2003-06-01

There are objects with some periods of higher than normal levels of risk of accidental atmospheric releases (nuclear, chemical, biological, etc.). Such accidents or events may occur due to natural hazards, human errors, terror acts, and during transportation of waste or various operations at high risk. A methodology for risk assessment is suggested and it includes two approaches: 1) probabilistic analysis of possible atmospheric transport patterns using long-term trajectory and dispersion modelling, and 2) forecast and evaluation of possible contamination and consequences for the environment and population using operational dispersion modelling. The first approach could be applied during the preparation stage, and the second - during the operation stage. The suggested methodology is applied on an example of the most important phases (lifting, transportation, and decommissioning) of the ``Kursk" nuclear submarine operation. It is found that the temporal variability of several probabilistic indicators (fast transport probability fields, maximum reaching distance, maximum possible impact zone, and average integral concentration of 137Cs) showed that the fall of 2001 was the most appropriate time for the beginning of the operation. These indicators allowed to identify the hypothetically impacted geographical regions and territories. In cases of atmospheric transport toward the most populated areas, the forecasts of possible consequences during phases of the high and medium potential risk levels based on a unit hypothetical release (e.g. 1 Bq) are performed. The analysis showed that the possible deposition fractions of 10-11 (Bq/m2) over the Kola Peninsula, and 10-12 - 10-13 (Bq/m2) for the remote areas of the Scandinavia and Northwest Russia could be observed. The suggested methodology may be used successfully for any potentially dangerous object involving risk of atmospheric release of hazardous materials of nuclear, chemical or biological nature.

49 CFR 176.99 - Permit requirements for certain hazardous materials.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Permit requirements for certain hazardous materials. 176.99 Section 176.99 Transportation Other Regulations Relating to Transportation PIPELINE AND... CARRIAGE BY VESSEL Special Requirements for Barges § 176.99 Permit requirements for certain hazardous...

Storage and transport of hazardous materials

International Nuclear Information System (INIS)

Jaeger, P.; Haferkamp, K.

1986-01-01

The attempt has been made to characterise the present risk scenario, and to set out approaches or methods for remedy and risk control. For this purpose, a retrospective analysis has been made of accidents, damage and consequential damage that occurred in the past either during storage of hazardous materials, or during road transport. A risk-benefit model facilitates assessment of accident frequency. The history of accidents during storage or transport allows assessment of the dangerousness of various materials. Another important aspect discussed is the property and behaviour of containers used for storage or transport. (DG) [de

Evaluation of methods to compare consequences from hazardous materials transportation accidents

International Nuclear Information System (INIS)

Rhoads, R.E.; Franklin, A.L.; Lavender, J.C.

1986-10-01

This report presents the results of a project to develop a framework for making meaningful comparisons of the consequences from transportation accidents involving hazardous materials. The project was conducted in two phases. In Phase I, methods that could potentially be used to develop the consequence comparisons for hazardous material transportation accidents were identified and reviewed. Potential improvements were identified and an evaluation of the improved methods was performed. Based on this evaluation, several methods were selected for detailed evaluation in Phase II of the project. The methods selected were location-dependent scenarios, figure of merit and risk assessment. This evaluation included application of the methods to a sample problem which compares the consequences of four representative hazardous materials - chlorine, propane, spent nuclear fuel and class A explosives. These materials were selected because they represented a broad class of hazardous material properties and consequence mechanisms. The sample case aplication relied extensively on consequence calculations performed in previous transportation risk assessment studies. A consultant was employed to assist in developing consequence models for explosives. The results of the detailed evaluation of the three consequence comparison methods indicates that methods are available to perform technically defensible comparisons of the consequences from a wide variety of hazardous materials. Location-dependent scenario and risk assessment methods are available now and the figure of merit method could be developed with additional effort. All of the methods require substantial effort to implement. Methods that would require substantially less effort were identified in the preliminary evaluation, but questions of technical accuracy preclude their application on a scale. These methods may have application to specific cases, however

Perceived safety of transporting hazardous materials

International Nuclear Information System (INIS)

Reese, R.T.; Shepherd, E.W.

1981-01-01

A framework for relating the variables involved in the public perception of hazardous materials transportation was presented. The framework consisted of a conditional mathematical equation in which perceived safety was described by six basic terms (technical feasibility, political palatability, social responsibility, utility assessment, media interpretation, and familiarity as a function of time). The resulting framework provides the technologist with an initial formulation to better understand public perception

GIS risk analysis of hazardous materials transport

International Nuclear Information System (INIS)

Anders, C.; Olsten, J.

1991-01-01

The Geographic Information System (GIS) was used to assess the risks and vulnerability of transporting hazardous materials and wastes (such as gasoline, explosives, poisons, etc) on the Arizona highway system. This paper discusses the methodology that was utilized, and the application of GIS systems to risk analysis problems

Ranking system for mixed radioactive and hazardous waste sites

International Nuclear Information System (INIS)

Hawley, K.A.; Napier, B.A.

1985-01-01

The Environmental Protection Agency's Hazard Ranking System (HRS) is a simplified management decision tool that provides a common basis for evaluating a multitude of hazardous waste sites. A deficiency in the HRS for application to Department of Energy mixed radioactive and hazardous waste sites is its inability to explicitly handle radioactive material. A modification to the basic HRS to add the capability to consider radioactivity is described. The HRS considers the exposure routes of direct contact, fire/explosion, atmospheric release, surface-water release, and ground-water release. Each exposure route is further divided into release, route, containment, waste, and target characteristics. To maintain the basic HRS structure, only the waste characteristics section of each exposure route was modified. A ranking system was developed, using radiation dose pathway analysis, to group radionuclides by dose factors. For mixed waste sites, the ranking factor derived for radionuclides is compared with the ranking factor obtained for hazardous chemicals and the most restrictive is used in the overall ranking. The modified HRS has the advantages of being compatible with the original HRS, has reasonable information requirements, and provides scientifically defensible conclusions. 17 references, 2 figures, 6 tables

Feasibility study--computerized application of the hazardous material regulations

International Nuclear Information System (INIS)

Ferrada, J.J.; Green, V.M.; Rawl, R.R.

1992-09-01

The feasibility of developing a full expert system for transportation and packaging of hazardous and radioactive materials was initiated within the framework of three subtasks: (1) analysis of commercial packages related to regulation scanning, (2) analysis of computer languages to develop the expert system, and (3) development of expert system prototypes. The strategy to develop the latter subtask was to first,develop modules to capture the knowledge of different areas of transportation and packaging and second, to analyze the feasibility of appending these different modules in one final full package. The individual modules development contemplated one prototype for transporting and packaging of radioactive material and another for transporting hazardous chemical materials. In the event that it is not feasible to link these two packages, the modules can always be used as stand-alone tools, or linked as a single package with some restrictions in their applicability. The work done during this fiscal year has focused on developing a prototype for transporting radioactive materials

78 FR 60726 - Hazardous Materials Regulations: Penalty Guidelines

Science.gov (United States)

2013-10-02

... new categories: Offeror Requirements for specific hazardous materials: Oxygen Generators and Batteries... protecting public health, welfare, safety, and our environment.'' Executive Order 13610 further instructs... the human environment. When developing potential regulatory requirements, PHMSA evaluates those...

Hazardous materials management using a Cradle-to-Grave Tracking and Information System (CGTIS)

Energy Technology Data Exchange (ETDEWEB)

Kjeldgaard, E.; Fish, J.; Campbell, D.; Freshour, N.; Hammond, B.; Bray, O. [Sandia National Labs., Albuquerque, NM (United States); Hollingsworth, M. [Ogden Environmental & Energy Services Co., Inc., Albuquerque, NM (United States)

1995-03-01

Hazardous materials management includes interactions among materials, personnel, facilities, hazards, and processes of various groups within a DOE site`s environmental, safety & health (ES&H) and line organizations. Although each group is charged with addressing a particular aspect of these properties and interactions, the information it requires must be gathered into a coherent set of common data for accurate and consistent hazardous material management and regulatory reporting. It is these common data requirements which the Cradle-to-Grave Tracking and Information System (CGTIS) is designed to satisfy. CGTIS collects information at the point at which a process begins or a material enters a facility, and maintains that information, for hazards management and regulatory reporting, throughout the entire life-cycle by providing direct on-line links to a site`s multitude of data bases to bring information together into one common data model.

Hazardous materials management using a Cradle-to-Grave Tracking and Information System (CGTIS)

International Nuclear Information System (INIS)

Kjeldgaard, E.; Fish, J.; Campbell, D.; Freshour, N.; Hammond, B.; Bray, O.; Hollingsworth, M.

1995-03-01

Hazardous materials management includes interactions among materials, personnel, facilities, hazards, and processes of various groups within a DOE site's environmental, safety ampersand health (ES ampersand H) and line organizations. Although each group is charged with addressing a particular aspect of these properties and interactions, the information it requires must be gathered into a coherent set of common data for accurate and consistent hazardous material management and regulatory reporting. It is these common data requirements which the Cradle-to-Grave Tracking and Information System (CGTIS) is designed to satisfy. CGTIS collects information at the point at which a process begins or a material enters a facility, and maintains that information, for hazards management and regulatory reporting, throughout the entire life-cycle by providing direct on-line links to a site's multitude of data bases to bring information together into one common data model

Hazards to nuclear plants from surface traffic accidents

International Nuclear Information System (INIS)

Hornyik, K.

1975-01-01

Analytic models have been developed for evaluating hazards to nuclear plants from hazardous-materials accidents in the vicinity of the plant. In particular, these models permit the evaluation of hazards from such accidents occurring on surface traffic routes near the plant. The analysis uses statistical information on accident rates, traffic frequency, and cargo-size distribution along with parameters describing properties of the hazardous cargo, plant design, and atmospheric conditions, to arrive at a conservative estimate of the annual probability of a catastrophic event. Two of the major effects associated with hazardous-materials accidents, explosion and release of toxic vapors, are treated by a common formalism which can be readily applied to any given case by means of a graphic procedure. As an example, for a typical case it is found that railroad shipments of chlorine in 55-ton tank cars constitute a greater hazard to a nearby nuclear plant than equally frequent rail shipments of explosives in amounts of 10 tons. 11 references. (U.S.)

A survey on hazardous materials accidents during road transport in China from 2000 to 2008

International Nuclear Information System (INIS)

Yang Jie; Li Fengying; Zhou Jingbo; Zhang Ling; Huang Lei; Bi Jun

2010-01-01

A study of 322 accidents that occurred during the road transport of hazardous materials (hazmat) in China from 2000 to 2008 was carried out. The results showed an increase in the frequency of accidents from 2000 to 2007 and a decline in 2008. More than 63% of the accidents occurred in the eastern coastal areas, 25.5% in the central inland areas, and only 10.9% in the western remote areas. The most frequent types of accident were releases (84.5%), followed by gas clouds (13.0%), fires (10.2%), no substance released due to timely measures (9.9%), and explosions (5.9%). The spatial distribution, the causes and consequences of the accidents related to the population (e.g., number of people killed, injured, evacuated, or poisoned), and environment elements were analyzed. Finally, conclusions are drawn concerning the need to improve certain safety measures in the road transport of hazmat in China.

Prevention and mitigation of groundwater contamination from radioactive releases

International Nuclear Information System (INIS)

1988-10-01

This document gives basic information on potential pathways and mechanisms, by which radioactive materials from releases can reach man, and on modelling considerations to predict the behaviour of radioactive materials in the ground. The main objective is to present an overview of existing techniques for preventing the offsite releases of contaminants into the groundwater systems and techniques for mitigation of effects of such releases should they occur. The recommended techniques are fully applicable to any hazardous materials, such as organic liquids, and toxic materials or otherwise dangerous materials, the presence of which in the accessible biosphere can represent health risks as well as economic losses to the general public. 11 refs, 2 figs, 8 tabs

Assessment of fire hazards in buildings housing fusion energy experiments

International Nuclear Information System (INIS)

Alvares, N.; Lipska, A.

1978-01-01

A number of materials in and within the proximity of buildings housing fusion energy experiments (FEE) were analyzed for their potential fire hazard. The materials used in this study were mostly: electrical and thermal insulations. The fire hazard of these materials was assessed in terms of their ease of ignition, heat release rate, generation of smoke, and the effect of thermal environment on the combustion behavior. Several fire protection measures for buildings housing the (FEE) projects are analyzed and as a result of this study are found to be adequate for the near term

Transport and Reactivity of Decontaminants to Provide Hazard Mitigation of Chemical Warfare Agents from Materials

Science.gov (United States)

2016-06-01

2013 4. TITLE AND SUBTITLE Transport and Reactivity of Decontaminants to Provide Hazard Mitigation of Chemical Warfare Agents from Materials 5a...directions for future decontamination formulation approaches. 15. SUBJECT TERMS GD HD Decontamination Hazard mitigation VX Chemical warfare agent... DECONTAMINANTS TO PROVIDE HAZARD MITIGATION OF CHEMICAL WARFARE AGENTS FROM MATERIALS 1. INTRODUCTION Decontamination of materials is the

Decision support for environmental management of industrial non-hazardous secondary materials: New analytical methods combined with simulation and optimization modeling.

Science.gov (United States)

Little, Keith W; Koralegedara, Nadeesha H; Northeim, Coleen M; Al-Abed, Souhail R

2017-07-01

Non-hazardous solid materials from industrial processes, once regarded as waste and disposed in landfills, offer numerous environmental and economic advantages when put to beneficial uses (BUs). Proper management of these industrial non-hazardous secondary materials (INSM) requires estimates of their probable environmental impacts among disposal as well as BU options. The U.S. Environmental Protection Agency (EPA) has recently approved new analytical methods (EPA Methods 1313-1316) to assess leachability of constituents of potential concern in these materials. These new methods are more realistic for many disposal and BU options than historical methods, such as the toxicity characteristic leaching protocol. Experimental data from these new methods are used to parameterize a chemical fate and transport (F&T) model to simulate long-term environmental releases from flue gas desulfurization gypsum (FGDG) when disposed of in an industrial landfill or beneficially used as an agricultural soil amendment. The F&T model is also coupled with optimization algorithms, the Beneficial Use Decision Support System (BUDSS), under development by EPA to enhance INSM management. Published by Elsevier Ltd.

Release of powdered material from waste packages

International Nuclear Information System (INIS)

Berg, H.P.; Gruendler, D.; Peiffer, F.; Seehars, H.D.

1990-01-01

Possible incidents in the operational phase of the planned German repository KONRAD for radioactive waste with negligible heat production were investigated to assess the radiological consequences. For these investigations release fractions of the radioactive materials are required. This paper deals with the determination of the release of powdered material from waste packages under mechanical stress. These determinations were based on experiments. The experimental procedure and the process parameters chosen in accordance with the conditions in the planned repository will be described. The significance of the experimental results is discussed with respect to incidents in the planned repository. 8 figs., 3 tabs

Hazards assessment for the INEL Landfill Complex

International Nuclear Information System (INIS)

Knudsen, J.K.; Calley, M.B.

1994-02-01

This report documents the hazards assessment for the INEL Landfill Complex (LC) located at the Idaho National Engineering Laboratory, which is operated by EG ampersand G Idaho, Inc., for the US Department of Energy (DOE). The hazards assessment was performed to ensure that this facility complies with DOE and company requirements pertaining to emergency planning and preparedness for operational emergencies. DOE Order 5500.3A requires that a facility-specific hazards assessment be performed to provide the technical basis for facility emergency planning efforts. This hazards assessment was conducted in accordance with DOE Headquarters and the DOE Idaho Operations Office (DOE-ID) guidance to comply with DOE Order 5500.3A. The hazards assessment identifies and analyzes the hazards that are significant enough to warrant consideration in a facility's operational emergency management program. The area surrounding the LC, the buildings and structures at the LC, and the processes that are used at the LC are described in this report. All hazardous materials, both radiological and nonradiological, at the LC were identified and screened against threshold quantities according to DOE Order 5500.3A guidance. Asbestos at the Asbestos Pit was the only hazardous material that exceeded its specified threshold quantity. However, the type of asbestos received and the packaging practices used are believed to limit the potential for an airborne release of asbestos fibers. Therefore, in accordance with DOE Order 5500.3A guidance, no further hazardous material characterization or analysis was required for this hazards assessment

Hazards assessment for the INEL Landfill Complex

Energy Technology Data Exchange (ETDEWEB)

Knudsen, J.K.; Calley, M.B.

1994-02-01

This report documents the hazards assessment for the INEL Landfill Complex (LC) located at the Idaho National Engineering Laboratory, which is operated by EG&G Idaho, Inc., for the US Department of Energy (DOE). The hazards assessment was performed to ensure that this facility complies with DOE and company requirements pertaining to emergency planning and preparedness for operational emergencies. DOE Order 5500.3A requires that a facility-specific hazards assessment be performed to provide the technical basis for facility emergency planning efforts. This hazards assessment was conducted in accordance with DOE Headquarters and the DOE Idaho Operations Office (DOE-ID) guidance to comply with DOE Order 5500.3A. The hazards assessment identifies and analyzes the hazards that are significant enough to warrant consideration in a facility`s operational emergency management program. The area surrounding the LC, the buildings and structures at the LC, and the processes that are used at the LC are described in this report. All hazardous materials, both radiological and nonradiological, at the LC were identified and screened against threshold quantities according to DOE Order 5500.3A guidance. Asbestos at the Asbestos Pit was the only hazardous material that exceeded its specified threshold quantity. However, the type of asbestos received and the packaging practices used are believed to limit the potential for an airborne release of asbestos fibers. Therefore, in accordance with DOE Order 5500.3A guidance, no further hazardous material characterization or analysis was required for this hazards assessment.

Hazardous Materials Verification and Limited Characterization Report on Sodium and Caustic Residuals in Materials and Fuel Complex Facilities MFC-799/799A

Energy Technology Data Exchange (ETDEWEB)

Gary Mecham

2010-08-01

This report is a companion to the Facilities Condition and Hazard Assessment for Materials and Fuel Complex Sodium Processing Facilities MFC-799/799A and Nuclear Calibration Laboratory MFC-770C (referred to as the Facilities Condition and Hazards Assessment). This report specifically responds to the requirement of Section 9.2, Item 6, of the Facilities Condition and Hazards Assessment to provide an updated assessment and verification of the residual hazardous materials remaining in the Sodium Processing Facilities processing system. The hazardous materials of concern are sodium and sodium hydroxide (caustic). The information supplied in this report supports the end-point objectives identified in the Transition Plan for Multiple Facilities at the Materials and Fuels Complex, Advanced Test Reactor, Central Facilities Area, and Power Burst Facility, as well as the deactivation and decommissioning critical decision milestone 1, as specified in U.S. Department of Energy Guide 413.3-8, “Environmental Management Cleanup Projects.” Using a tailored approach and based on information obtained through a combination of process knowledge, emergency management hazardous assessment documentation, and visual inspection, this report provides sufficient detail regarding the quantity of hazardous materials for the purposes of facility transfer; it also provides that further characterization/verification of these materials is unnecessary.

Hazard classification of environmental restoration activities at the INEL

International Nuclear Information System (INIS)

Peatross, R.G.

1996-04-01

The following documents require that a hazard classification be prepared for all activities for which US Department of Energy (DOE) has assumed environmental, safety, and health responsibility: the DOE Order 5481.1B, Safety Analysis and Review System and DOE Order 5480.23, Nuclear Safety Analysis Reports. A hazard classification defines the level of hazard posed by an operation or activity, assuming an unmitigated release of radioactive and nonradioactive hazardous material. For environmental restoration activities, the release threshold criteria presented in Hazard Baseline Documentation (DOE-EM-STD-5502-94) are used to determine classifications, such as Radiological, Nonnuclear, and Other Industrial facilities. Based upon DOE-EM-STD-5502-94, environmental restoration activities in all but one of the sites addressed by the scope of this classification (see Section 2) can be classified as ''Other Industrial Facility''. DOE-EM-STD-5502-94 states that a Health and Safety Plan and compliance with the applicable Occupational Safety and Health Administration (OSHA) standards are sufficient safety controls for this classification

Decontamination and management of human remains following incidents of hazardous chemical release.

Science.gov (United States)

Hauschild, Veronique D; Watson, Annetta; Bock, Robert

2012-01-01

To provide specific guidance and resources for systematic and orderly decontamination of human remains resulting from a chemical terrorist attack or accidental chemical release. A detailed review and health-based decision criteria protocol is summarized. Protocol basis and logic are derived from analyses of compound-specific toxicological data and chemical/physical characteristics. Guidance is suitable for civilian or military settings where human remains potentially contaminated with hazardous chemicals may be present, such as sites of transportation accidents, terrorist operations, or medical examiner processing points. Guidance is developed from data-characterizing controlled experiments with laboratory animals, fabrics, and materiel. Logic and specific procedures for decontamination and management of remains, protection of mortuary affairs personnel, and decision criteria to determine when remains are sufficiently decontaminated are presented. Established procedures as well as existing materiel and available equipment for decontamination and verification provide reasonable means to mitigate chemical hazards from chemically exposed remains. Unique scenarios such as those involving supralethal concentrations of certain liquid chemical warfare agents may prove difficult to decontaminate but can be resolved in a timely manner by application of the characterized systematic approaches. Decision criteria and protocols to "clear" decontaminated remains for transport and processing are also provided. Once appropriate decontamination and verification have been accomplished, normal procedures for management of remains and release can be followed.

77 FR 24885 - Hazardous Materials; Miscellaneous Amendments (RRR)

Science.gov (United States)

2012-04-26

... special provisions, clarify the lab pack requirements for temperature-controlled materials, and revise the... in Dewar flasks. Clarify the lab pack provisions in Sec. 173.12 pertaining to temperature-controlled... shipping names, hazard classes, packing groups, special provisions, packaging authorizations, air transport...

Calculation of Airborne Radioactivity Hazard from Machining Volume-Activated Materials

International Nuclear Information System (INIS)

E.T. Marshall; S.O. Schwahn

1997-01-01

When evaluating a task involving the machining of volume-activated materials, accelerator health physicists must consider more than the surface contamination levels of the equipment and containment of loose shavings, dust or filings. Machining operations such as sawing, routing, welding, and grinding conducted on volume-activated material may pose a significant airborne radioactivity hazard to the worker. This paper presents a computer spreadsheet notebook that conservatively estimates the airborne radioactivity levels generated during machining operations performed on volume-activated materials. By knowing (1) the size and type of materials, (2) the dose rate at a given distances, and (3) limited process knowledge, the Derived Air Concentration (DAC) fraction can be estimated. This tool is flexible, taking into consideration that the process knowledge available for the different materials varies. It addresses the two most common geometries: thick plane and circular cylinder. Once the DAC fraction has been estimated, controls can be implemented to mitigate the hazard to the worker

Calculation of airborne radioactivity hazard from machining volume-activated materials

International Nuclear Information System (INIS)

Marshall, E.T.; Schwahn, S.O.

1996-10-01

When evaluating a task involving the machining of volume-activated materials, accelerator health physicists must consider more than the surface contamination levels of the equipment and containment of loose shavings, dust or filings. Machining operations such as sawing, routing, welding, and grinding conducted on volume-activated material may pose a significant airborne radioactivity hazard to the worker. This paper presents a computer spreadsheet notebook that conservatively estimates the airborne radioactivity levels generated during machining operations performed on volume-activated materials. By knowing (1) the size and type of materials, (2) the dose rate at a given distances, and (3) limited process knowledge, the Derived Air Concentration (DAC) fraction can be estimated. This tool is flexible, taking into consideration that the process knowledge available for the different materials varies. It addresses the two most common geometries: thick plane and circular cylinder. Once the DAC fraction has been estimated, controls can be implemented to mitigate the hazard to the worker

Project plan, Hazardous Materials Management and Emergency Response Training Center: Project 95L-EWT-100

International Nuclear Information System (INIS)

Borgeson, M.E.

1994-01-01

The Hazardous Materials Management and Emergency Response (HAMMER) Training Center will provide for classroom lectures and hands-on practical training in realistic situations for workers and emergency responders who are tasked with handling and cleanup of toxic substances. The primary objective of the HAMMER project is to provide hands-on training and classroom facilities for hazardous material workers and emergency responders. This project will also contribute towards complying with the planning and training provisions of recent legislation. In March 1989 Title 29 Code of Federal Regulations Occupational Safety and Health Administration 1910 Rules and National Fire Protection Association Standard 472 defined professional requirements for responders to hazardous materials incidents. Two general types of training are addressed for hazardous materials: training for hazardous waste site workers and managers, and training for emergency response organizations

78 FR 16044 - Hazardous Materials Packaging-Composite Cylinder Standards; Public Meeting

Science.gov (United States)

2013-03-13

... Toughiry, Engineering and Research Division, Office of Hazardous Materials Safety, Pipeline and Hazardous... the HMR, ISO 11119 Parts-1, -2 and -3, contain design, construction and testing requirements that are.../permits-approvals/special-permits . II. Public Meeting Topics During this public meeting, PHMSA will...

Malicious release of radioactive materials in urban area. Exposure of the public and emergency staff, protective measures

International Nuclear Information System (INIS)

Koch, Wolfgang; Lange, Florentin

2016-01-01

The preparedness for hypothetical radiological scenarios is part of the tasks for governmental authorities, safety and emergency organizations and the staff in case of the incident. The EURATOM guideline for radiation protection has to be implemented into national laws. According to the guidelines it is required that emergency planning has to be prepared for hypothetical radiological scenarios including terroristic or other maliciously motivated attacks using radioactive materials. The study includes assumptions on the released respirable radioactivity, restriction of the hazardous area, wind induced re-suspension of radioactive dusts and inhalation exposure, and mitigation measures.

Preparedness of hazardous materials emergencies in railyards: Guidance for railroads and adjacent communities

Energy Technology Data Exchange (ETDEWEB)

1991-09-01

Railroads are a key part of the distribution system for hazardous materials and, thus, much hazardous material passes through railyards en route to intermediate or final consumers. While the vast majority of these materials are shipped without incident, both the number of shipments and the nature of the materials themselves dictate that railyards and surrounding communities be prepared to respond quickly and effectively to emergencies. This report contains information on 11 emergency preparedness functions and 150 guidance recommendations.

Radioactivity and associated radiation hazards in ceramic raw materials and end products.

Science.gov (United States)

Viruthagiri, G; Rajamannan, B; Suresh Jawahar, K

2013-12-01

Studies have been planned to obtain activity and associated radiation hazards in ceramic raw materials (quartz, feldspar, clay, zircon, kaolin, grog, alumina bauxite, baddeleyite, masse, dolomite and red mud) and end products (ceramic brick, glazed ceramic wall and floor tiles) as the activity concentrations of uranium, thorium and potassium vary from material to material. The primordial radionuclides in ceramic raw materials and end products are one of the sources of radiation hazard in dwellings made of these materials. By the determination of the activity level in these materials, the indoor radiological hazard to human health can be assessed. This is an important precautionary measure whenever the dose rate is found to be above the recommended limits. The aim of this work was to measure the activity concentration of (226)Ra, (232)Th and (40)K in ceramic raw materials and end products. The activity of these materials has been measured using a gamma-ray spectrometry, which contains an NaI(Tl) detector connected to multichannel analyser (MCA). Radium equivalent activity, alpha-gamma indices and radiation hazard indices associated with the natural radionuclides are calculated to assess the radiological aspects of the use of the ceramic end products as decorative or covering materials in construction sector. Results obtained were examined in the light of the relevant international legislation and guidance and compared with the results of similar studies reported in different countries. The results suggest that the use of ceramic end product samples examined in the construction of dwellings, workplace and industrial buildings is unlikely to give rise to any significant radiation exposure to the occupants.

Radioactivity and associated radiation hazards in ceramic raw materials and end products

International Nuclear Information System (INIS)

Viruthagiri, G.; Rajamannan, B.; Suresh Jawahar, K.

2013-01-01

Studies have been planned to obtain activity and associated radiation hazards in ceramic raw materials (quartz, feldspar, clay, zircon, kaolin, grog, alumina bauxite, baddeleyite, masse, dolomite and red mud) and end products (ceramic brick, glazed ceramic wall and floor tiles) as the activity concentrations of uranium, thorium and potassium vary from material to material. The primordial radionuclides in ceramic raw materials and end products are one of the sources of radiation hazard in dwellings made of these materials. By the determination of the activity level in these materials, the indoor radiological hazard to human health can be assessed. This is an important precautionary measure whenever the dose rate is found to be above the recommended limits. The aim of this work was to measure the activity concentration of 226 Ra, 232 Th and 40 K in ceramic raw materials and end products. The activity of these materials has been measured using a gamma-ray spectrometry, which contains an NaI(Tl) detector connected to multichannel analyser (MCA). Radium equivalent activity, alpha-gamma indices and radiation hazard indices associated with the natural radionuclides are calculated to assess the radiological aspects of the use of the ceramic end products as decorative or covering materials in construction sector. Results obtained were examined in the light of the relevant international legislation and guidance and compared with the results of similar studies reported in different countries. The results suggest that the use of ceramic end product samples examined in the construction of dwellings, workplace and industrial buildings is unlikely to give rise to any significant radiation exposure to the occupants. (authors)

Numerical investigation of debris materials prior to debris flow hazards using satellite images

Science.gov (United States)

Zhang, N.; Matsushima, T.

2018-05-01

The volume of debris flows occurred in mountainous areas is mainly affected by the volume of debris materials deposited at the valley bottom. Quantitative evaluation of debris materials prior to debris flow hazards is important to predict and prevent hazards. At midnight on 7th August 2010, two catastrophic debris flows were triggered by the torrential rain from two valleys in the northern part of Zhouqu City, NW China, resulting in 1765 fatalities and huge economic losses. In the present study, a depth-integrated particle method is adopted to simulate the debris materials, based on 2.5 m resolution satellite images. In the simulation scheme, the materials are modeled as dry granular solids, and they travel down from the slopes and are deposited at the valley bottom. The spatial distributions of the debris materials are investigated in terms of location, volume and thickness. Simulation results show good agreement with post-disaster satellite images and field observation data. Additionally, the effect of the spatial distributions of the debris materials on subsequent debris flows is also evaluated. It is found that the spatial distributions of the debris materials strongly influence affected area, runout distance and flow discharge. This study might be useful in hazard assessments prior to debris flow hazards by investigating diverse scenarios in which the debris materials are unknown.

Center for Integrated Nanotechnologies (CINT) Chemical Release Modeling Evaluation

Energy Technology Data Exchange (ETDEWEB)

Stirrup, Timothy Scott [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2016-12-20

This evaluation documents the methodology and results of chemical release modeling for operations at Building 518, Center for Integrated Nanotechnologies (CINT) Core Facility. This evaluation is intended to supplement an update to the CINT [Standalone] Hazards Analysis (SHA). This evaluation also updates the original [Design] Hazards Analysis (DHA) completed in 2003 during the design and construction of the facility; since the original DHA, additional toxic materials have been evaluated and modeled to confirm the continued low hazard classification of the CINT facility and operations. This evaluation addresses the potential catastrophic release of the current inventory of toxic chemicals at Building 518 based on a standard query in the Chemical Information System (CIS).

Mission: Possible. Center of Excellence for Hazardous Materials Management

International Nuclear Information System (INIS)

Bartlett, W.T.; Prather-Stroud, W.

2006-01-01

The Center of Excellence for Hazardous Materials Management (CEHMM) was established in May 2004 as a nonprofit research organization. Its purpose is to develop a sustainable technical/scientific community located in Carlsbad, New Mexico, that interacts worldwide to find solutions to hazardous materials management issues. An important part of the mission is to achieve improved protection of worker safety, human health, and the environment. Carlsbad has a large technical community due to the presence of the Waste Isolation Pilot Plant (WIPP) and its many contractors and support organizations. These groups include the Carlsbad Environmental Monitoring and Research Center, Washington Group International, Los Alamos National Laboratory, and Sandia National Laboratories. These organizations form the basis of a unique knowledge community with strengths in many areas, such as geosciences, actinide chemistry, environmental monitoring, and waste transportation. CEHMM works cooperatively with these organizations and others to develop projects that will maintain this knowledge community beyond the projected closure date of WIPP. At present, there is an emphasis in bio-monitoring, air monitoring, hazardous materials educational programs, and endangered species remediation. CEHMM is also currently working with a group from the American Nuclear Society to help facilitate their conference scheduled for April 2006 in Carlsbad. CEHMM is growing rapidly and is looking forward to a diverse array of new projects. (authors)

HABIT, Toxic and Radioactive Release Hazards in Reactor Control Room

International Nuclear Information System (INIS)

Stage, S.A.

2005-01-01

1 - Description of program or function: HABIT is a package of computer codes designed to be used for the evaluation of control room habitability in the event of an accidental release of toxic chemicals or radioactive materials. 2 - Methods: Given information about the design of a nuclear power plant, a scenario for the release of toxic or radionuclides, and information about the air flows and protection systems of the control room, HABIT can be used to estimate the chemical exposure or radiological dose to control room personnel

Transport of hazardous materials in the Amazon area; Transporte de produtos perigosos na regiao Amazonica

Energy Technology Data Exchange (ETDEWEB)

Cunha, Wallace de Castro [FURNAS Centrais Eletricas S.A., Rio de Janeiro, RJ (Brazil); Fernandes, Elton; Nassi, Carlos David [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Coordenacao dos Programas de Pos-Graduacao de Engenharia (COPPE)

2008-07-01

Amongst several exploratory sources of the subject 'hazardous materials transport', it is distinguished: 'the threat to the environment'. This paper presents an exploratory investigation of this subject line in the Amazon region. In view of the diversity of 'existing hazardous materials' and the raised dimension of the oil transport and its derivatives in this context, this paper focused in these products. Regarding to the geographic region, the approach was given to the State of Amazon, considering the amplitude of this State in the Amazon region and the availability of data. Therefore, this work explores and analyzes macro aspects inherent to the State of Amazon pertinent to the oil transport and its derivatives. In the macro context, it is observed the necessity of a higher control in the transport of hazardous materials in the region. The absence of registered data and the unfamiliarity on the risks related to the transport of hazardous materials by authorities and transporters indicate a relative absence of qualification in the region to deal with the monitoring of the transport of hazardous materials. So far, it is not possible up till now to make any evaluation of the environment threats of accidents with transport of hazardous materials in the Amazon region.(author)

Transport of hazardous materials in the Amazon area; Transporte de produtos perigosos na regiao Amazonica

Energy Technology Data Exchange (ETDEWEB)

Cunha, Wallace de Castro [FURNAS Centrais Eletricas S.A., Rio de Janeiro, RJ (Brazil); Fernandes, Elton; Nassi, Carlos David [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Coordenacao dos Programas de Pos-Graduacao de Engenharia (COPPE)

2008-07-01

Amongst several exploratory sources of the subject 'hazardous materials transport', it is distinguished: 'the threat to the environment'. This paper presents an exploratory investigation of this subject line in the Amazon region. In view of the diversity of 'existing hazardous materials' and the raised dimension of the oil transport and its derivatives in this context, this paper focused in these products. Regarding to the geographic region, the approach was given to the State of Amazon, considering the amplitude of this State in the Amazon region and the availability of data. Therefore, this work explores and analyzes macro aspects inherent to the State of Amazon pertinent to the oil transport and its derivatives. In the macro context, it is observed the necessity of a higher control in the transport of hazardous materials in the region. The absence of registered data and the unfamiliarity on the risks related to the transport of hazardous materials by authorities and transporters indicate a relative absence of qualification in the region to deal with the monitoring of the transport of hazardous materials. So far, it is not possible up till now to make any evaluation of the environment threats of accidents with transport of hazardous materials in the Amazon region.(author)

Radioactive materials released from nuclear power plants (1976)

International Nuclear Information System (INIS)

Decker, T.R.

1978-11-01

Releases of radioactive materials in airborne and liquid effluents from commercial light water reactors during 1976 have been compiled and reported. Data on solid waste shipments as well as selected operating information have been included. This report supplements earlier annual reports issued by the former Atomic Energy Commission and the Nuclear Regulatory Commission. The 1976 release data are compared with previous year releases in tabular form. Data covering specific radionuclides are summarized

Simulated atmospheric disperison of radioactive material released in an urban area

International Nuclear Information System (INIS)

Akins, R.E.; Church, H.W.; Tierney, M.S.

1977-01-01

A combination of Gaussian plume and particle-in-cell techniques is used to simulate the atmospheric transport and dispersion of a puff release of radioactive material. The release is caused by an accident that is assumed to occur during the shipment of the radioactive material through central New York City. The simulation provides estimates of volumetric and surface concentrations of the dispersed material that are used to predict radiation doses incurred by the City's population in the event of an accidental release. In the simulation, the release point is arbitrary and the material is assumed to be either a gas or fine particles. The Gaussian plume model follows cloud concentrations from the release time until times when transport over distances up to 500 m has been achieved. The released cloud may stabilize at street level or above the mean buildings height; at a street intersection or in the middle of the block. The possibility of the formation of multiple clouds, owing to circumstances of wind flow direction and street geometry, is allowed

Radioactive materials released from nuclear power plants

International Nuclear Information System (INIS)

Tichler, J.; Norden, K.; Congemi, J.

1991-05-01

Releases of radioactive materials in airborne and liquid effluents from commercial light water reactors during 1988 have been compiled and reported. Data on solid waste shipments as well as selected operating information have been included. This report supplements earlier annual reports issued by the former Atomic Energy Commission and the Nuclear Regulatory Commission. The 1988 release data are summarized in tabular form. Data covering specific radionuclides are summarized. 16 tabs

75 FR 38168 - Hazardous Materials: International Regulations for the Safe Transport of Radioactive Material (TS...

Science.gov (United States)

2010-07-01

... may also provide contact information, such as a telephone number and/or e-mail address. PHMSA and the.... PHMSA-2010-0130 (Notice No.10-2)] Hazardous Materials: International Regulations for the Safe Transport... (IAEA) ``Regulations for the Safe Transport of Radioactive Material'' (TS-R-1), which is scheduled for...

Sandia National Laboratories, California Hazardous Materials Management Program annual report : February 2009.

Energy Technology Data Exchange (ETDEWEB)

Brynildson, Mark E.

2009-02-01

The annual program report provides detailed information about all aspects of the Sandia National Laboratories, California (SNL/CA) Hazardous Materials Management Program. It functions as supporting documentation to the SNL/CA Environmental anagement ystem Program Manual. This program annual report describes the activities undertaken during the past year, and activities planned in future years to implement the Hazardous Materials Management Program, one of six programs that supports environmental management at SNL/CA.

A proposal for a test method for assessment of hazard property HP 12 ("Release of an acute toxic gas") in hazardous waste classification - Experience from 49 waste.

Science.gov (United States)

Hennebert, Pierre; Samaali, Ismahen; Molina, Pauline

2016-12-01

A stepwise method for assessment of the HP 12 is proposed and tested with 49 waste samples. The hazard property HP 12 is defined as "Release of an acute toxic gas": waste which releases acute toxic gases (Acute Tox. 1, 2 or 3) in contact with water or an acid. When a waste contains a substance assigned to one of the following supplemental hazards EUH029, EUH031 and EUH032, it shall be classified as hazardous by HP 12 according to test methods or guidelines (EC, 2014a, 2014b). When the substances with the cited hazard statement codes react with water or an acid, they can release HCl, Cl 2 , HF, HCN, PH 3 , H 2 S, SO 2 (and two other gases very unlikely to be emitted, hydrazoic acid HN 3 and selenium oxide SeO 2 - a solid with low vapor pressure). Hence, a method is proposed:For a set of 49 waste, water addition did not produce gas. Nearly all the solid waste produced a gas in contact with hydrochloric acid in 5 min in an automated calcimeter with a volume >0.1L of gas per kg of waste. Since a plateau of pressure is reached only for half of the samples in 5 min, 6 h trial with calorimetric bombs or glass flasks were done and confirmed the results. Identification of the gases by portable probes showed that most of the tested samples emit mainly CO 2 . Toxic gases are emitted by four waste: metallic dust from the aluminum industry (CO), two air pollution control residue of industrial waste incinerator (H 2 S) and a halogenated solvent (organic volatile(s) compound(s)). HF has not been measured in these trials started before the present definition of HP 12. According to the definition of HP 12, only the H 2 S emission of substances with hazard statement EUH031 is accounted for. In view of the calcium content of the two air pollution control residue, the presence of calcium sulphide (EUH031) can be assumed. These two waste are therefore classified potentially hazardous for HP 12, from a total of 49 waste. They are also classified as hazardous for other properties (HP 7

Quality Assurance Program Plan for the Hazardous Materials Transportation and Packaging Program. Revision 1

Energy Technology Data Exchange (ETDEWEB)

Calihan, T.W. III; Votaw, E.F.

1995-05-01

This QAPP covers only the implementation accomplished through Level I and II manuals. It covers the quality affecting activities identified in USDOE orders (both HQ and Richland Operations Office), US DOT, US EPA, and NRC regulations, IAEA guidelines, and the WHC manuals. It covers activities related to hazardous materials transportation performed on and off the Hanford site under the jurisdictional authority of WHC. (Hazardous materials include radioactive, hazardous waste, and mixed waste.)

Quality Assurance Program Plan for the Hazardous Materials Transportation and Packaging Program. Revision 1

International Nuclear Information System (INIS)

Calihan, T.W. III; Votaw, E.F.

1995-01-01

This QAPP covers only the implementation accomplished through Level I and II manuals. It covers the quality affecting activities identified in USDOE orders (both HQ and Richland Operations Office), US DOT, US EPA, and NRC regulations, IAEA guidelines, and the WHC manuals. It covers activities related to hazardous materials transportation performed on and off the Hanford site under the jurisdictional authority of WHC. (Hazardous materials include radioactive, hazardous waste, and mixed waste.)

Inclusion of cefalexin in SBA-15 mesoporus material and release property

International Nuclear Information System (INIS)

Zhai, Qing-Zhou

2012-01-01

SBA-15 (Santa Barbara Amorphous-15) is a high ordered mesoporous material. It has the advantages of a non-toxic property, good hydrothermal stability and thermal stability, etc. Inside inner surface a lot of silanols exist. Pore diameter size is uniform and pore size distribution is narrow. This structural feature makes SBA-15 have a higher loading drug amount and be able to effectively extend the drug release cycle. In this paper, polyethylene glycol-block-polypropylene glycol-block-polyethylene glycol was used as template and tetraethyl orthosilicate was used as silica source to prepare SBA-15 by hydrothermal synthesis method. Cefalexin was included in SBA-15 and the included cefalexin drug content was 158.72 mg/g. The composite materials were characterized by using chemical analysis, powder X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), infrared (IR) spectroscopy, and low temperature nitrogen adsorption–desorption. The results showed that cefalexin had been successfully included in host SBA-15 pore channels. Rational analyses of the release processes of cefalexin drug from the pores of SBA-15 to the simulated body fluid, simulated gastric juice and simulated intestinal fluid were made and sustained-release effects of the drug in complex system were studied. The results showed that in simulated body fluid within 1–5 h cefalexin was fast released and the cumulative release reached 50.00% at 5 h. In 15–20 h, the sustained release speed of cefalexin drug in the composite material decreased and the sustained-release cumulative amount reached 99.87% at 20 h. The release of cefalexin was basically complete. In simulated gastric fluid, composite material sustained-release ended at 4 h, the cumulative sustained release ratio reaching 26.10%. In simulated gastric fluid, the sustained-release was complete at 7 h, the cumulative sustained release ratio reaching 32.46%. The composite material of SBA-15 and cefalexin

77 FR 39662 - Hazardous Materials; Reverse Logistics (RRR)

Science.gov (United States)

2012-07-05

... logistics providers estimate that up to 7% of an enterprise's gross sales are return costs. The third-party... logistic shipments for hazardous materials? III. Issues To Be Considered As previously noted, the purpose... documentation costs to develop and maintain risk assessments and operational procedures? If so, what is a fair...

Assessment of consequences from airborne releases of radioactive material

International Nuclear Information System (INIS)

McGrath, P.E.; Blond, R.M.

1976-01-01

Over the past several years, the manner in which assessments have been made of the consequences of large airborne releases of radioactive material has not changed much conceptually. The models to describe the atmospheric dispersion of the radioactive material have generally been time-invariant, i.e., the meteorological conditions (thermal stability, wind speed, and precipitation) are invariant during release and the subsequent period of radiation exposure of the population to the airborne material. The frequency distribution of the meteorological conditions are determined by analyzing several years of weather data from the appropriate geographical location. In reality, weather is continuously changing over short time periods (hours) following the release. It is to be expected that the changing meteorological conditions would have important effects on the potential consequences of the release. A time-dependent atmospheric dispersion model was developed and implemented in the Reactor Safety Study. This paper provides a description of the model and the nature of the results generated. Emphasis is given to an explanation of how, and why, these results differ from those estimated with time-invariant models

Influence of factors on release of antimicrobials from antimicrobial packaging materials.

Science.gov (United States)

Wu, Yu-Mei; Wang, Zhi-Wei; Hu, Chang-Ying; Nerín, Cristina

2018-05-03

Antimicrobial packaging materials (films or coatings) (APMs) have aroused great interest among the scientists or the experts specialized in material science, food science, packaging engineering, biology and chemistry. APMs have been used to package the food, such as dairy products, poultry, meat (e.g., beef), salmon muscle, pastry dough, fresh pasta, bakery products, fruits, vegetables and beverages. Some materials have been already commercialized. The ability of APMs to extend the shelf-life of the food depends on the release rate of the antimicrobials (AMs) from the materials to the food. The optimum rate is defined as target release rate (TRR). To achieve TRR, the influencing factors of the release rate should be considered. Herein we reviewed for the first time these factors and their influence on the release. These factors mainly include the AMs, food (or food simulant), packaging materials, the interactions among them, the temperature and environmental relative humidity (RH).

Review on fluoride-releasing restorative materials--fluoride release and uptake characteristics, antibacterial activity and influence on caries formation.

Science.gov (United States)

Wiegand, Annette; Buchalla, Wolfgang; Attin, Thomas

2007-03-01

The purpose of this article was to review the fluoride release and recharge capabilities, and antibacterial properties, of fluoride-releasing dental restoratives, and discuss the current status concerning the prevention or inhibition of caries development and progression. Information from original scientific full papers or reviews listed in PubMed (search term: fluoride release AND (restorative OR glass-ionomer OR compomer OR polyacid-modified composite resin OR composite OR amalgam)), published from 1980 to 2004, was included in the review. Papers dealing with endodontic or orthodontic topics were not taken into consideration. Clinical studies concerning secondary caries development were only included when performed in split-mouth design with an observation period of at least three years. Fluoride-containing dental materials show clear differences in the fluoride release and uptake characteristics. Short- and long-term fluoride releases from restoratives are related to their matrices, setting mechanisms and fluoride content and depend on several environmental conditions. Fluoride-releasing materials may act as a fluoride reservoir and may increase the fluoride level in saliva, plaque and dental hard tissues. However, clinical studies exhibited conflicting data as to whether or not these materials significantly prevent or inhibit secondary caries and affect the growth of caries-associated bacteria compared to non-fluoridated restoratives. Fluoride release and uptake characteristics depend on the matrices, fillers and fluoride content as well as on the setting mechanisms and environmental conditions of the restoratives. Fluoride-releasing materials, predominantly glass-ionomers and compomers, did show cariostatic properties and may affect bacterial metabolism under simulated cariogenic conditions in vitro. However, it is not proven by prospective clinical studies whether the incidence of secondary caries can be significantly reduced by the fluoride release of

Emergency response network design for hazardous materials transportation with uncertain demand

Directory of Open Access Journals (Sweden)

Kamran Shahanaghi

2012-10-01

Full Text Available Transportation of hazardous materials play an essential role on keeping a friendly environment. Every day, a substantial amount of hazardous materials (hazmats, such as flammable liquids and poisonous gases, need to be transferred prior to consumption or disposal. Such transportation may result in unsuitable events for people and environment. Emergency response network is designed for this reason where specialist responding teams resolve any issue as quickly as possible. This study proposes a new multi-objective model to locate emergency response centers for transporting the hazardous materials. Since many real-world applications are faced with uncertainty in input parameters, the proposed model of this paper also assumes that reference and demand to such centre is subject to uncertainty, where demand is fuzzy random. The resulted problem formulation is modelled as nonlinear non-convex mixed integer programming and we used NSGAII method to solve the resulted problem. The performance of the proposed model is examined with several examples using various probability distribution and they are compared with the performance of other existing method.

49 CFR 176.76 - Transport vehicles, freight containers, and portable tanks containing hazardous materials.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Transport vehicles, freight containers, and... TRANSPORTATION HAZARDOUS MATERIALS REGULATIONS CARRIAGE BY VESSEL General Handling and Stowage § 176.76 Transport... paragraphs (b) through (f) of this section, hazardous materials authorized to be transported by vessel may be...

Final hazard classification for N basin water filtration and sediment relocation operations

International Nuclear Information System (INIS)

Pisarcik, D.J.; Kretzschmar, S.P.

1996-02-01

This document provides an auditable safety analysis and hazard classification for the filtration of basin water and the relocation of 105-N basin solids to the North Cask Pit within the basin complex. This report assesses the operation of the Water Filtration System and the Remotely Operated Sediment Extraction Equipment (ROSEE). These activities have an activity hazard classification of radiological. Inventories of potentially releasable nonradioactive hazardous materials are far below the reportable quantities of 40 CFR 302. No controls are required to maintain the releasable inventories of these materials below the reportable quantities. Descriptive material is included to provide a general understanding of the water filtration and sediment relocation processes. All equipment will be operated as described in work instructions and/or applicable procedures. Special controls associated with these activities are as follows: (1) A leak inspection of the ROSEE system shall be performed at least once every 5-hour period of sediment relocation operation. (2) A berm must be in place around the North Cask Pit to redirect a potential abovewater ROSEE system leak back to the basin

The development of the American National Standard 'control of radioactive surface contamination on materials equipment and facilities to be released for uncontrolled use'

International Nuclear Information System (INIS)

Shapiro, J.

1980-01-01

A new standard submitted by the Health Physics Society Standards Committee to the American National Standards Institute concerning radioactive surface contamination of materials and equipment is discussed. The chronological events in the development of this standard are given. The standard provides criteria for the release for uncontrolled use of materials, equipment and facilities contaminated or potentially contaminated with radioactivity. Permissible contamination limits are specified for: 1) long lived alpha emitters except natural uranium and thorium, 2) more hazardous beta-gamma emitters, 3) less hazardous beta-gamma emitters and 4) natural uranium and thorium. A contamination reference level of 1000 dpm/100 cm 2 for 90 Sr was set as the basis for assigning limits to radionuclides presenting an ingestion hazard and other radionuclides were grouped based on the values of their maximum permissible concentration (MPC) in water relative to 90 Sr. The contamination limit for 239 Pu was chosen as the basis for assigning limits based on MPC in air to radionuclides presenting an inhalation hazard; a value of 100 dpm/100 cm 2 was adopted in the standard. An upper limit of 5000 dpm/100 cm 2 for surface contamination was selected for the standard. (UK)

Exploratory Studies Facility Subsurface Fire Hazards Analysis

International Nuclear Information System (INIS)

Logan, Richard C.

2002-01-01

The primary objective of this Fire Hazard Analysis (FHA) is to confirm the requirements for a comprehensive fire and related hazards protection program for the Exploratory Studies Facility (ESF) are sufficient to minimize the potential for: The occurrence of a fire or related event; A fire that causes an unacceptable on-site or off-site release of hazardous or radiological material that will threaten the health and safety of employees, the public or the environment; Vital U.S. Department of Energy (DOE) programs suffering unacceptable interruptions as a result of fire and related hazards; Property losses from a fire and related events exceeding limits established by DOE; and Critical process controls and safety class systems being damaged as a result of a fire and related events

FIRE HAZARDS ANALYSIS - BUSTED BUTTE

International Nuclear Information System (INIS)

Longwell, R.; Keifer, J.; Goodin, S.

2001-01-01

The purpose of this fire hazards analysis (FHA) is to assess the risk from fire within individual fire areas at the Busted Butte Test Facility and to ascertain whether the DOE fire safety objectives are met. The objective, identified in DOE Order 420.1, Section 4.2, is to establish requirements for a comprehensive fire and related hazards protection program for facilities sufficient to minimize the potential for: (1) The occurrence of a fire related event. (2) A fire that causes an unacceptable on-site or off-site release of hazardous or radiological material that will threaten the health and safety of employees. (3) Vital DOE programs suffering unacceptable interruptions as a result of fire and related hazards. (4) Property losses from a fire and related events exceeding limits established by DOE. Critical process controls and safety class systems being damaged as a result of a fire and related events

49 CFR 171.1 - Applicability of Hazardous Materials Regulations (HMR) to persons and functions.

Science.gov (United States)

2010-10-01

... $250 for each violation, except the maximum civil penalty is $110,000 if the violation results in death... and functions. Federal hazardous materials transportation law (49 U.S.C. 5101 et seq.) directs the... regulations to persons who transport hazardous materials in commerce. In addition, the law authorizes the...

76 FR 73011 - Pipeline and Hazardous Materials Safety Administration

Science.gov (United States)

2011-11-28

... DEPARTMENT OF TRANSPORTATION Pipeline and Hazardous Materials Safety Administration Office of... Safety Administration (PHMSA), DOT. ACTION: Notice of actions on Special Permit Applications. SUMMARY: In... reissue the Nuclear 173.56(b)(3)(i special permit Security ). originally issued Administration on an...

Sulfur Release from Cement Raw Materials during Solid Fuel Combustion

DEFF Research Database (Denmark)

Nielsen, Anders Rooma; Larsen, Morten B.; Glarborg, Peter

2011-01-01

During combustion of solid fuels in the material inlet end of cement rotary kilns, local reducing conditions can occur and cause decomposition of sulfates from cement raw materials. Decomposition of sulfates is problematic because it increases the gas-phase SO2 concentration, which may cause...... deposit formation in the kiln system. SO2 release from cement raw materials during combustion of solid fuels has been studied experimentally in a high temperature rotary drum. The fuels were tire rubber, pine wood, petcoke, sewage sludge, and polypropylene. The SO2 release from the raw materials...

Assessment of the Potential Release of Radioactivity from Installations at AERE, Harwell. Implications for Emergency Planning

Energy Technology Data Exchange (ETDEWEB)

Flew, Elizabeth M.; Lister, B. A.J. [Atomic Energy Research Establishment, Harwell, Didcot, Berks. (United Kingdom)

1969-10-15

As part of a review of the site emergency organization at AERE, a realistic reappraisal has been made of the potential hazard to the establishment and district of all the buildings containing significant amounts of radioactive materials. To assess the amount of radioactive material which might be released under specified accident conditions, four factors have been applied to the total building stock: (a) the fraction of the stock involved, (b) the percentage conversion to an aerosol form, (c) release from primary containment and (d) release from the building. These potential release figures have been compared with ''site hazardous release'' figures for relevant radionuclides i.e., amounts which could give rise to exposure above defined reference levels. Those buildings with more than one tenth of the potential for causing; a site or district hazard have been designated ''risk buildings''. Such a quantitative assessment, although necessarily very approximate, has been of considerable value in determining the type and complexity of the central emergency organization required and in producing the right emphasis on exercises, training, liaison with outside bodies, etc. (author)

ENVIRONMENTALLY SOUND DISPOSAL OF RADIOACTIVE MATERIALS AT A RCRA HAZARDOUS WASTE DISPOSAL FACILITY

International Nuclear Information System (INIS)

Romano, Stephen; Welling, Steven; Bell, Simon

2003-01-01

The use of hazardous waste disposal facilities permitted under the Resource Conservation and Recovery Act (''RCRA'') to dispose of low concentration and exempt radioactive materials is a cost-effective option for government and industry waste generators. The hazardous and PCB waste disposal facility operated by US Ecology Idaho, Inc. near Grand View, Idaho provides environmentally sound disposal services to both government and private industry waste generators. The Idaho facility is a major recipient of U.S. Army Corps of Engineers FUSRAP program waste and received permit approval to receive an expanded range of radioactive materials in 2001. The site has disposed of more than 300,000 tons of radioactive materials from the federal government during the past five years. This paper presents the capabilities of the Grand View, Idaho hazardous waste facility to accept radioactive materials, site-specific acceptance criteria and performance assessment, radiological safety and environmental monitoring program information

Analysis on tank truck accidents involved in road hazardous materials transportation in china.

Science.gov (United States)

Shen, Xiaoyan; Yan, Ying; Li, Xiaonan; Xie, Chenjiang; Wang, Lihua

2014-01-01

Due to the sheer size and capacity of the tanker and the properties of cargo transported in the tank, hazmat tanker accidents are more disastrous than other types of vehicle accidents. The aim of this study was to provide a current survey on the situation of accidents involving tankers transporting hazardous materials in China. Detailed descriptions of 708 tanker accidents associated with hazmat transportation in China from 2004 to 2011 were analyzed to identify causes, location, types, time of occurrence, hazard class for materials involved, consequences, and the corresponding probability. Hazmat tanker accidents mainly occurred in eastern (38.1%) and southwest China (12.3%). The most frequent hazmat tanker accidents involved classes 2, 3, and 8. The predominant accident types were rollover (29.10%), run-off-the-road (16.67%), and rear-end collisions (13.28%), with a high likelihood of a large spill occurring. About 55.93% of the accidents occurred on freeways and class 1 roads, with the spill percentage reaching 75.00% and the proportion of spills that occurred in the total accidents amounting to 77.82%, of which 61.72% are considered large spills. The month with the highest accident probability was July (12.29%), and most crashes occurred during the early morning (4:00-6:00 a.m.) and midday (10:00 a.m.-12:00 p.m.) hours, 19.63% versus 16.10%. Human-related errors (73.8%) and vehicle-related defects (19.6%) were the primary reasons for hazmat tanker crashes. The most common outcomes of a hazmat tanker accident was a spill without further events (55.51%), followed by a release with fire (7.77%), and release with an explosion (2.54%). The safety situation of China's hazmat tanker transportation is grim. Such accidents not only have high spill percentages and consistently large spills but they can also cause serious consequences, such as fires and explosions. Improving the training of drivers and the quality of vehicles, deploying roll stability aids, enhancing

Hazardous Material Cargo Frustration at Military Aerial Ports of Embarkation

National Research Council Canada - National Science Library

Christensen, Neil E

2006-01-01

Since military units often require critical hazardous materials in an expedited manner, identifying choke points within the supply chain is necessary to improve logistic support to front line forces...

Evaluation of hydrophobic materials as matrices for controlled-release drug delivery.

Science.gov (United States)

Quadir, Mohiuddin Abdul; Rahman, M Sharifur; Karim, M Ziaul; Akter, Sanjida; Awkat, M Talat Bin; Reza, Md Selim

2003-07-01

The present study was undertaken to evaluate the effect of different insoluble and erodable wax-lipid based materials and their content level on the release profile of drug from matrix systems. Matrix tablets of theophylline were prepared using carnauba wax, bees wax, stearic acid, cetyl alcohol, cetostearyl alcohol and glyceryl monostearate as rate-retarding agents by direct compression process. The release of theophylline from these hydrophobic matrices was studied over 8-hours in buffer media of pH 6.8. Statistically significant difference was found among the drug release profile from different matrices. The release kinetics was found to be governed by the type and content of hydrophobic materials in the matrix. At lower level of wax matrices (25%), a potential burst release was observed with all the materials being studied. Bees wax could not exert any sustaining action while an extensive burst release was found with carnauba wax at this hydrophobic load. Increasing the concentration of fat-wax materials significantly decreased the burst effect of drug from the matrix. At higher hydrophobic level (50% of the matrix), the rate and extent of drug release was significantly reduced due to increased tortuosity and reduced porosity of the matrix. Cetostearyl alcohol imparted the strongest retardation of drug release irrespective of fat-wax level. Numerical fits indicate that the Higuchi square root of time model was the most appropriate one for describing the release profile of theophylline from hydrophobic matrices. The release mechanism was also explored and explained with biexponential equation. Application of this model indicates that Fickian or case I kinetics is the predominant mechanism of drug release from these wax-lipid matrices. The mean dissolution time (MDT) was calculated for all the formulations and the highest MDT value was obtained with cetostearyl matrix. The greater sustaining activity of cetostearyl alcohol can be attributed to some level of

Hazardous Materials Transportation Act. Hearing before the Subcommittee on Transportation, Tourism, and Hazardous Materials of the Committee on Energy and Commerce, House of Representatives, One Hundredth Congress, First Session, July 30, 1987

Energy Technology Data Exchange (ETDEWEB)

1988-01-01

About 1.5 billion tons of hazardous materials per year are moved in the US by truck, rail, barge, and air. The Hazardous Materials Transportation Act was the first attempt at a comprehensive Federal scheme for regulation. This hearing looks at the Secretary of Transportation's implementation of the statute for oversight and reauthorization responsibilities. Testimony was heard from 16 witnesses, representatives of Chemical Manufacturers Association, the American Trucking Association, the Association of American Railroads, the Department of Transportation, the Environmental Protection Agency, the Environmental Policy Institute, Office of Technology Assessment, Hazardous Materials Advisory Council, National Tank Truck Carriers, Federal Emergency Management Agency, National Paint and Coatings Association, and a representative from Ohio.

The environmental impact of radioactive releases from accidents in nuclear power reactors

International Nuclear Information System (INIS)

Beattie, J.R.; Griffiths, R.F.; Kaiser, G.D.; Kinchin, G.H.

1978-01-01

A survey of accidental releases of radioactivity from thermal and fast reactors is presented. Following a general discussion on the hazards involved, the nature of the environmental impact of radioactive releases is examined. This includes a brief review of the natural radiation background, the effect on human health of various levels of radiation and radioactivity, permissible and reference levels, and the type of hazards from both passing clouds of airbourne radioactive material and from ground deposited material. The problem of atmospheric dispersion and methods of calculations of radioactive materials in the atmosphere are examined in order for the consequences of accidental release to be analysed. National accidents and their environmental consequences are then examined. Finally there is a review of the risks to which man is always exposed because of his environment. Common and collective risks are also considered. Conclusions are reached as to the acceptibility or otherwise of the environmental impact of reactor accidents. (U.K.)

78 FR 1119 - Hazardous Materials: Transportation of Lithium Batteries

Science.gov (United States)

2013-01-07

...: Transportation of Lithium Batteries AGENCY: Pipeline and Hazardous Materials Safety Administration (PHMSA), DOT... lithium cells and batteries that have been adopted into the 2013-2014 International Civil Aviation... edition, when transporting batteries domestically by air. Incorporation by reference of the 2013-2014...

Safety in the Chemical Laboratory: Certifications for Professional Hazardous Materials and Waste Management.

Science.gov (United States)

Fischer, Kenneth E.

1988-01-01

Discusses the need for determining a curriculum to provide qualified hazardous waste personnel. Describes the needed role of colleges and universities and current hazardous materials certification requirements. Lists requirements for 18 professional certifications. (MVL)

Development of an expert system for transportation of hazardous and radioactive materials

International Nuclear Information System (INIS)

Ferrada, J.J.; Michelhaugh, R.D.; Rawl, R.R.

1994-01-01

Under the sponsorship of the US Department of Energy's (DOE's) Transportation Management Division (EM-261), the Transportation Technologies Group at Oak Ridge National Laboratory (ORNL) has designed and developed an expert system prototype application of the hazardous materials transportation regulations. The objective of this task was to provide a proof-of-concept for developing a computerized expert system that will ensure straightforward, consistent, and error-free application of the hazardous materials transportation regulations. The expert system prototype entailed the analysis of what an expert in hazardous materials shipping information could/should do. From the analysis of the different features required for the expert system prototype, it was concluded that the developmental efforts should be directed to a Windows trademark 3.1 hypermedia environment. Hypermedia technology usually works as an interactive software system that gives personal computer users the ability to organize, manage, and present information in a number of formats--text, graphics, sound, and full-motion video

Model for absorption and release of gaseous materials by forest canopies

International Nuclear Information System (INIS)

Murphy, C.E. Jr.

1976-01-01

A model of the physical processes defining the absorption and release of materials by a forest canopy has been developed. The model deals with the turbulent transport of gaseous materials in the surface boundary layer near the canopy, the turbulent transport in the canopy atmosphere, the transport through the boundary layer near the leaf and soil surface, and the solution of the gaseous materials in intracellular fluids and subsequent diffusion into the leaf cells. The model is used to simulate the uptake of molecular tritium by the forest canopy and the subsequent release of tritiated water. Results of dynamic simulations of tritium uptake and release are compared with data collected at the time of a release of molecular tritium to the atmosphere

Natural hazards that may trigger a radiological release from a plutonium processing facility

Energy Technology Data Exchange (ETDEWEB)

Selvidge, J. E.

1977-04-28

Calculations show the probability of a tornado striking a plutonium area at Rocky Flats is 2.2 x 10/sup -4/ per year. The source term (expected value of plutonium release) should such an event occur is calculated at 3.3 x 10/sup -7/ grams. The source term for high-velocity, downslope winds is higher--2.2 x 10/sup -3/ grams. The probability of a meteorite that weighs one or more pounds (453 grams) striking a plutonium area is estimated at 8.88 x 10/sup -7/ per year. Because of this small probability and the remote chance that a plutonium release would occur even if a meteorite hit occurred, the hazard from meteorite impact is considered negligible. Conservative assumptions result in all calculated frequencies being almost certainly too high. Empirical observations have indicated lower frequencies than those calculated.

Natural hazards that may trigger a radiological release from a plutonium processing facility

International Nuclear Information System (INIS)

Selvidge, J.E.

1977-01-01

Calculations show the probability of a tornado striking a plutonium area at Rocky Flats is 2.2 x 10 -4 per year. The source term (expected value of plutonium release) should such an event occur is calculated at 3.3 x 10 -7 grams. The source term for high-velocity, downslope winds is higher--2.2 x 10 -3 grams. The probability of a meteorite that weighs one or more pounds (453 grams) striking a plutonium area is estimated at 8.88 x 10 -7 per year. Because of this small probability and the remote chance that a plutonium release would occur even if a meteorite hit occurred, the hazard from meteorite impact is considered negligible. Conservative assumptions result in all calculated frequencies being almost certainly too high. Empirical observations have indicated lower frequencies than those calculated

77 FR 21714 - Hazardous Materials: Transportation of Lithium Batteries

Science.gov (United States)

2012-04-11

...: Transportation of Lithium Batteries AGENCY: Pipeline and Hazardous Materials Safety Administration (PHMSA), DOT... cells and batteries that have been adopted into the 2013-2014 International Civil Aviation Organization...) to address the air transportation risks posed by lithium cells and batteries. Some of the proposals...

75 FR 1302 - Hazardous Materials: Transportation of Lithium Batteries

Science.gov (United States)

2010-01-11

... of Lithium Batteries AGENCY: Pipeline and Hazardous Materials Safety Administration (PHMSA), DOT... transportation of lithium cells and batteries, including lithium cells and batteries packed with or contained in equipment. The proposed changes are intended to enhance safety by ensuring that all lithium batteries are...

Stimuli-Responsive Materials for Controlled Release Applications

KAUST Repository

Li, Song

2015-01-01

The controlled release of therapeutics has been one of the major challenges for scientists and engineers during the past three decades. To address this outstanding problem, the design and fabrication of stimuli-responsive materials are pursued

Estimated airborne release of plutonium from the 102 Building at the General Electric Vallecitos Nuclear Center, Vallecitos, California, as a result of postulated damage from severe wind and earthquake hazard

International Nuclear Information System (INIS)

Mishima, J.; Ayer, J.E.; Hays, I.D.

1980-12-01

This report estimates the potential airborne releases of plutonium as a consequence of various severities of earthquake and wind hazard postulated for the 102 Building at the General Electric Vallecitos Nuclear Center in California. The releases are based on damage scenarios developed by other specialists. The hazard severities presented range up to a nominal velocity of 230 mph for wind hazard and are in excess of 0.8 g linear acceleration for earthquakes. The consequences of thrust faulting are considered. The approaches and factors used to estimate the releases are discussed. Release estimates range from 0.003 to 3 g Pu

Exploratory Studies Facility Subsurface Fire Hazards Analysis

International Nuclear Information System (INIS)

Kubicek, J. L.

2001-01-01

The primary objective of this Fire Hazard Analysis (FHA) is to confirm the requirements for a comprehensive fire and related hazards protection program for the Exploratory Studies Facility (ESF) are sufficient to minimize the potential for: (1) The occurrence of a fire or related event. (2) A fire that causes an unacceptable on-site or off-site release of hazardous or radiological material that will threaten the health and safety of employees, the public or the environment. (3) Vital US. Department of Energy (DOE) programs suffering unacceptable interruptions as a result of fire and related hazards. (4) Property losses from a fire and related events exceeding limits established by DOE. (5) Critical process controls and safety class systems being damaged as a result of a fire and related events

Preliminary proposed seismic design and evaluation criteria for new and existing underground hazardous materials storage tanks

International Nuclear Information System (INIS)

Kennedy, R.P.

1991-01-01

The document provides a recommended set of deterministic seismic design and evaluation criteria for either new or existing underground hazardous materials storage tanks placed in either the high hazard or moderate hazard usage catagories of UCRL-15910. The criteria given herein are consistent with and follow the same philosophy as those given in UCRL-15910 for the US Department of Energy facilities. This document is intended to supplement and amplify upon Reference 1 for underground hazardous materials storage tanks

Investigation of Appropriate Applications for Reuse of Conditionally Released Materials from Decommissioning

International Nuclear Information System (INIS)

Daniska, V.; Vasko, M.; Necas, V.

2012-01-01

During the decommissioning (D and D) phase of nuclear facility life cycle a lot of original facility materials are generated as a primary decommissioning waste. One portion of these materials is unconditionally releasable, i.e. their radioactivity content is below the stipulated concentration limits for clearance thus they can be further recycled or dumped without any constraints as a conventional waste. Second portion of generated waste is waste with radioactivity content higher than limits for free release and it has to be handled and disposed of as the radioactive waste (RAW) within special RAW repositories. Disposal of RAW is quite expensive therefore it seems to be reasonable to reduce amount of waste destined for disposal and to identify RAW with radioactivity content slightly higher than stipulated concentration limits for unconditional release which could be released with some constraints for further recycling and reuse while stipulated safety requirements are observed, i.e. conditional release of RAW. The most perspective materials from decommissioning for such material reuse are steel and concrete. These materials can be reused within the long term robust constructions for applications with infrequent or only short time presence of personnel/public, minimum interaction of human with materials and controllable interaction of materials with environment. Ideal applications for deployment of such materials are steel reinforcement in pylons for highways, tunnel linings, industry prefabricates, big tanks or linings in nuclear applications, for concrete debris it can be filling material for road construction. Presented paper deals with preconditions for reuse of conditionally released materials. It maps legal pre-requisites in the Slovak Republic, appropriate material application scenarios, methodology of assessment of impact on human health and environment - external and internal exposure assessment, possible optimisation of scenarios and estimation of

Preliminary hazard classification for Building 107-N

International Nuclear Information System (INIS)

Kloster, G.L.; Smith, R.L.

1997-06-01

Deactivation activities are planned for Building 107-N (Basin Recirculation Building). This document establishes the preliminary hazard classification (PHC) for the 100-N Area facility segment that includes this building.To establish the PHC, the inventories of radioactive and nonradioactive hazardous materials present within Building 107-N are identified and then compared to the corresponding threshold quantity values in DOE (1992) and reportable quantity values in 40 CFR 302.4. In this evaluation, no credit is taken for the form, location, and dispersibility of the materials; for their interaction with available energy sources; or for safety features that could prevent or mitigate a radioactive release. The result of this effort concluded that the PHC for Building 107-N is Nuclear Category 3

Tank farms hazards assessment

International Nuclear Information System (INIS)

Broz, R.E.

1994-01-01

Hanford contractors are writing new facility specific emergency procedures in response to new and revised US Department of Energy (DOE) Orders on emergency preparedness. Emergency procedures are required for each Hanford facility that has the potential to exceed the criteria for the lowest level emergency, an Alert. The set includes: (1) a facility specific procedure on Recognition and Classification of Emergencies, (2) area procedures on Initial Emergency Response and, (3) an area procedure on Protective Action Guidance. The first steps in developing these procedures are to identify the hazards at each facility, identify the conditions that could release the hazardous material, and calculate the consequences of the releases. These steps are called a Hazards Assessment. The final product is a document that is similar in some respects to a Safety Analysis Report (SAR). The document could br produced in a month for a simple facility but could take much longer for a complex facility. Hanford has both types of facilities. A strategy has been adopted to permit completion of the first version of the new emergency procedures before all the facility hazards Assessments are complete. The procedures will initially be based on input from a task group for each facility. This strategy will but improved emergency procedures in place sooner and therefore enhance Hanford emergency preparedness. The purpose of this document is to summarize the applicable information contained within the Waste Tank Facility ''Interim Safety Basis Document, WHC-SD-WM-ISB-001'' as a resource, since the SARs covering Waste Tank Operations are not current in all cases. This hazards assessment serves to collect, organize, document and present the information utilized during the determination process

Removal of radioactive and other hazardous material from fluid waste

Science.gov (United States)

Tranter, Troy J [Idaho Falls, ID; Knecht, Dieter A [Idaho Falls, ID; Todd, Terry A [Aberdeen, ID; Burchfield, Larry A [W. Richland, WA; Anshits, Alexander G [Krasnoyarsk, RU; Vereshchagina, Tatiana [Krasnoyarsk, RU; Tretyakov, Alexander A [Zheleznogorsk, RU; Aloy, Albert S [St. Petersburg, RU; Sapozhnikova, Natalia V [St. Petersburg, RU

2006-10-03

Hollow glass microspheres obtained from fly ash (cenospheres) are impregnated with extractants/ion-exchangers and used to remove hazardous material from fluid waste. In a preferred embodiment the microsphere material is loaded with ammonium molybdophosphonate (AMP) and used to remove radioactive ions, such as cesium-137, from acidic liquid wastes. In another preferred embodiment, the microsphere material is loaded with octyl(phenyl)-N-N-diisobutyl-carbamoylmethylphosphine oxide (CMPO) and used to remove americium and plutonium from acidic liquid wastes.

Transformation of the released asbestos, carbon fibers and carbon nanotubes from composite materials and the changes of their potential health impacts.

Science.gov (United States)

Wang, Jing; Schlagenhauf, Lukas; Setyan, Ari

2017-02-20

Composite materials with fibrous reinforcement often provide superior mechanical, thermal, electrical and optical properties than the matrix. Asbestos, carbon fibers and carbon nanotubes (CNTs) have been widely used in composites with profound impacts not only on technology and economy but also on human health and environment. A large number of studies have been dedicated to the release of fibrous particles from composites. Here we focus on the transformation of the fibrous fillers after their release, especially the change of the properties essential for the health impacts. Asbestos fibers exist in a large number of products and the end-of-the-life treatment of asbestos-containing materials poses potential risks. Thermal treatment can transform asbestos to non-hazardous phase which provides opportunities of safe disposal of asbestos-containing materials by incineration, but challenges still exist. Carbon fibers with diameters in the range of 5-10 μm are not considered to be respirable, however, during the release process from composites, the carbon fibers may be split along the fiber axis, generating smaller and respirable fibers. CNTs may be exposed on the surface of the composites or released as free standing fibers, which have lengths shorter than the original ones. CNTs have high thermal stability and may be exposed after thermal treatment of the composites and still keep their structural integrity. Due to the transformation of the fibrous fillers during the release process, their toxicity may be significantly different from the virgin fibers, which should be taken into account in the risk assessment of fiber-containing composites.

An OSHA based approach to safety analysis for nonradiological hazardous materials

International Nuclear Information System (INIS)

Yurconic, M.

1992-08-01

The PNL method for chemical hazard classification defines major hazards by means of a list of hazardous substances (or chemical groups) with associated trigger quantities. In addition, the functional characteristics of the facility being classified is also be factored into the classification. In this way, installations defined as major hazard will only be those which have the potential for causing very serious incidents both on and off site. Because of the diversity of operations involving chemicals, it may not be possible to restrict major hazard facilities to certain types of operations. However, this hazard classification method recognizes that in the industrial sector major hazards are most commonly associated with activities involving very large quantities of chemicals and inherently energetic processes. These include operations like petrochemical plants, chemical production, LPG storage, explosives manufacturing, and facilities which use chlorine, ammonia, or other highly toxic gases in bulk quantities. The basis for this methodology is derived from concepts used by OSHA in its proposed chemical process safety standard, the Dow Fire and Explosion Index Hazard Classification Guide, and the International Labor Office's program on chemical safety. For the purpose of identifying major hazard facilities, this method uses two sorting criteria, (1) facility function and processes and (2) quantity of substances to identify facilities requiringclassification. Then, a measure of chemical energy potential (material factor) is used to identify high hazard class facilities

Enantioselectively controlled release of chiral drug (metoprolol) using chiral mesoporous silica materials

Energy Technology Data Exchange (ETDEWEB)

Guo Zhen; Liu Xianbin; Ng, Siu-Choon; Chen Yuan; Yang Yanhui [School of Chemical and Biomedical Engineering, Nanyang Technological University, Singapore 637459 (Singapore); Du Yu, E-mail: du_yu@jlu.edu.cn, E-mail: yhyang@ntu.edu.sg [College of Electronic Science and Engineering, Jilin University, Changchun 130012 (China)

2010-04-23

Chiral porous materials have attracted burgeoning attention on account of their potential applications in many areas, such as enantioseparation, chiral catalysis, chemical sensors and drug delivery. In this report, chiral mesoporous silica (CMS) materials with various pore sizes and structures were prepared using conventional achiral templates (other than chiral surfactant) and a chiral cobalt complex as co-template. The synthesized CMS materials were characterized by x-ray diffraction, nitrogen physisorption, scanning electron microscope and transmission electron microscope. These CMS materials, as carriers, were demonstrated to be able to control the enantioselective release of a representative chiral drug (metoprolol). The release kinetics, as modeled by the power law equation, suggested that the release profiles of metoprolol were remarkably dependent on the pore diameter and pore structure of CMS materials. More importantly, R- and S-enantiomers of metoprolol exhibited different release kinetics on CMS compared to the corresponding achiral mesoporous silica (ACMS), attributable to the existence of local chirality on the pore wall surface of CMS materials. The chirality of CMS materials on a molecular level was further substantiated by vibrational circular dichroism measurements.

Enantioselectively controlled release of chiral drug (metoprolol) using chiral mesoporous silica materials

International Nuclear Information System (INIS)

Guo Zhen; Liu Xianbin; Ng, Siu-Choon; Chen Yuan; Yang Yanhui; Du Yu

2010-01-01

Chiral porous materials have attracted burgeoning attention on account of their potential applications in many areas, such as enantioseparation, chiral catalysis, chemical sensors and drug delivery. In this report, chiral mesoporous silica (CMS) materials with various pore sizes and structures were prepared using conventional achiral templates (other than chiral surfactant) and a chiral cobalt complex as co-template. The synthesized CMS materials were characterized by x-ray diffraction, nitrogen physisorption, scanning electron microscope and transmission electron microscope. These CMS materials, as carriers, were demonstrated to be able to control the enantioselective release of a representative chiral drug (metoprolol). The release kinetics, as modeled by the power law equation, suggested that the release profiles of metoprolol were remarkably dependent on the pore diameter and pore structure of CMS materials. More importantly, R- and S-enantiomers of metoprolol exhibited different release kinetics on CMS compared to the corresponding achiral mesoporous silica (ACMS), attributable to the existence of local chirality on the pore wall surface of CMS materials. The chirality of CMS materials on a molecular level was further substantiated by vibrational circular dichroism measurements.

Methodology for performing measurements to release material from radiological control

International Nuclear Information System (INIS)

Durham, J.S.; Gardner, D.L.

1993-09-01

This report describes the existing and proposed methodologies for performing measurements of contamination prior to releasing material for uncontrolled use at the Hanford Site. The technical basis for the proposed methodology, a modification to the existing contamination survey protocol, is also described. The modified methodology, which includes a large-area swipe followed by a statistical survey, can be used to survey material that is unlikely to be contaminated for release to controlled and uncontrolled areas. The material evaluation procedure that is used to determine the likelihood of contamination is also described

Expert systems for the transportation of hazardous and radioactive materials

International Nuclear Information System (INIS)

Luce, C.E.; Clover, J.C.; Ferrada, J.J.

1994-01-01

Under the supervision of the Transportation Technologies Group which is in the Chemical Technology Division at Oak Ridge National Laboratory, an expert system prototype for the transportation and packaging of hazardous and radioactive materials has been designed and developed. The development of the expert system prototype focused on using the combination of hypermedia elements and the Visual Basic trademark programming language. Hypermedia technology uses software that allows the user to interact with the computing environment through many formats: text, graphics, audio, and full-motion video. With the use of hypermedia, a user-friendly prototype has been developed to sort through numerous transportation regulations, thereby leading to the proper packaging for the materials. The expert system performs the analysis of regulations that an expert in shipping information would do; only the expert system performs the work more quickly. Currently, enhancements in a variety of categories are being made to the prototype. These include further expansion of non-radioactive materials, which includes any material that is hazardous but not radioactive; and the addition of full-motion video, which will depict regulations in terms that are easy to understand and which will show examples of how to handle the materials when packaging them

75 FR 9147 - Hazardous Materials: Transportation of Lithium Batteries

Science.gov (United States)

2010-03-01

...: Transportation of Lithium Batteries AGENCY: Pipeline and Hazardous Materials Safety Administration (PHMSA), DOT... transport of lithium cells and batteries. PHMSA and FAA will hold a public meeting on March 5, 2010, in... will be attending the Lithium Battery Public Meeting and wait to be escorted to the Conference Center...

49 CFR 171.16 - Detailed hazardous materials incident reports.

Science.gov (United States)

2010-10-01

... containing any hazardous material suffers structural damage to the lading retention system or damage that..., explosion or dangerous evolution of heat (i.e., an amount of heat sufficient to be dangerous to packaging or personal safety to include charring of packaging, melting of packaging, scorching of packaging, or other...

Waste Issues Associated with the Safe Movement of Hazardous Chemicals

International Nuclear Information System (INIS)

Dare, J. H.; Cournoyer, M. E.

2002-01-01

Moving hazardous chemicals presents the risk of exposure for workers engaged in the activity and others that might be in the immediate area. Adverse affects are specific to the chemicals and can range from minor skin, eye, or mucous membrane irritation, to burns, respiratory distress, nervous system dysfunction, or even death. A case study is presented where in the interest of waste minimization; original shipping packaging was removed from a glass bottle of nitric acid, while moving corrosive liquid through a security protocol into a Radiological Control Area (RCA). During the transfer, the glass bottle broke. The resulting release of nitric acid possibly exposed 12 employees with one employee being admitted overnight at a hospital for observation. This is a clear example of administrative controls to reduce the generation of suspect radioactive waste being implemented at the expense of employee health. As a result of this event, material handling procedures that assure the safe movement of hazardous chemicals through a security protocol into a radiological control area were developed. Specifically, hazardous material must be transferred using original shipping containers and packaging. While this represents the potential to increase the generation of suspect radioactive waste in a radiological controlled area, arguments are presented that justify this change. Security protocols for accidental releases are also discussed. In summary, the 12th rule of ''Green Chemistry'' (Inherently Safer Chemistry for Accident Prevention) should be followed: the form of a substance used in a chemical process (Movement of Hazardous Chemicals) should be chosen to minimize the potential for chemical accidents, including releases

Waste Issues Associated with the Safe Movement of Hazardous Chemicals

Energy Technology Data Exchange (ETDEWEB)

Dare, J. H.; Cournoyer, M. E.

2002-02-26

Moving hazardous chemicals presents the risk of exposure for workers engaged in the activity and others that might be in the immediate area. Adverse affects are specific to the chemicals and can range from minor skin, eye, or mucous membrane irritation, to burns, respiratory distress, nervous system dysfunction, or even death. A case study is presented where in the interest of waste minimization; original shipping packaging was removed from a glass bottle of nitric acid, while moving corrosive liquid through a security protocol into a Radiological Control Area (RCA). During the transfer, the glass bottle broke. The resulting release of nitric acid possibly exposed 12 employees with one employee being admitted overnight at a hospital for observation. This is a clear example of administrative controls to reduce the generation of suspect radioactive waste being implemented at the expense of employee health. As a result of this event, material handling procedures that assure the safe movement of hazardous chemicals through a security protocol into a radiological control area were developed. Specifically, hazardous material must be transferred using original shipping containers and packaging. While this represents the potential to increase the generation of suspect radioactive waste in a radiological controlled area, arguments are presented that justify this change. Security protocols for accidental releases are also discussed. In summary, the 12th rule of ''Green Chemistry'' (Inherently Safer Chemistry for Accident Prevention) should be followed: the form of a substance used in a chemical process (Movement of Hazardous Chemicals) should be chosen to minimize the potential for chemical accidents, including releases.

Modelling of motorway tunnels scenario for utilization of conditionally released radioactive materials

International Nuclear Information System (INIS)

Hrncir, Tomas; Panik, Michal; Necas, Vladimir

2011-01-01

Considerable amount of solid radioactive waste with radioactivity slightly above the limits for unconditional release is generated during the decommissioning of the nuclear installations. Conditional release deals with precisely this type of materials with activity slightly above limits in order to save considerable financial resources, which would be otherwise spend on treatment, conditioning and disposal of these materials at appropriate repository. The basic principles of conditional release as well as possibilities of reusing of the conditionally released materials are described. One of these possibilities of the reusing was chosen and application proposal of conditional release of metal waste - steel reinforcement in the concrete, which could be used for construction of motorway tunnels, was created. The computer code Visiplan 4.0 3D ALARA planning tool software was used for the calculation of effective individual dose for personnel constructing the tunnel and for critical group related to scenario. Particular models for individual scenarios of conditional release have been developed within the scope of this software code. The aim of the paper is to determine a level of the radioactivity of conditional released materials to avoid over exceeding the value of annual individual effective dose 10μSv/year established by international recommendations. (author)

Monitoring of the release of gaseous and aerosol-bound radioactive materials. Pt. 2

International Nuclear Information System (INIS)

1992-01-01

KTA 1503 contains requirements on technical installations and supplementary organizational measures considered necessary in order to monitor the release of gaseous and aerosol-bound radioactive materials. It consists of part 1: Monitoring of the release of radioactive materials together with stack gas during normal operation; part 2: Monitoring of the release of radioactive materials together with stack gas in the event of incidents; part 3: Monitoring of radioactive materials not released together with stack gas. The concept on which this rule is based is to ensure that in the case of incidents during which the result of effluent monitoring remains meaningful, such monitoring can be reliably performed. (orig./HSCH) [de

78 FR 66326 - Hazardous Materials: Rail Petitions and Recommendations To Improve the Safety of Railroad Tank...

Science.gov (United States)

2013-11-05

...: Rail Petitions and Recommendations To Improve the Safety of Railroad Tank Car Transportation (RRR) AGENCY: Pipeline and Hazardous Materials Safety Administration (PHMSA), DOT. ACTION: Advance Notice of... DEPARTMENT OF TRANSPORTATION Pipeline and Hazardous Materials Safety Administration 49 CFR Parts...

Human biological monitoring for exposure assessment in response to an incident involving hazardous materials.

Science.gov (United States)

Scheepers, Paul T J; van Brederode, Nelly E; Bos, Peter M J; Nijhuis, Nicole J; van de Weerdt, Rik H J; van der Woude, Irene; Eggens, Martin L

2014-12-15

Biological monitoring in humans (HBM) is widely used in the field of occupational and environmental health. In the situation of an unexpected release of hazardous materials HBM may contribute to the medical support and treatment of exposed individuals from the general population or of emergency responders. Such exposure information may also be used to respond to individual concerns such as questions about a possible relationship between the chemicals released during the incident and health effects. In The Netherlands a guideline was prepared to support early decision-making about the possible use of HBM for exposure assessment during or as soon as possible following a chemical incident. The application of HBM in such an emergency setting is not much different from situations where HBM is normally used but there are some issues that need extra attention such as the choice of the biomarker, the biological media to be sampled, the time point at which biological samples should be collected, the ethics approval and technical implementation of the study protocol and the interpretation and communication of the study results. These issues addressed in the new guideline will support the use of HBM in the management of chemical disasters. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Hazardous materials responder training in the new millennium

Energy Technology Data Exchange (ETDEWEB)

Turpin, R.D.; Betsinger, G.B. [U.S. Environmental Protection Agency, Edison, NJ (United States). Environmental Response Team; Merchant, S. [Environmental Tectonics Corp., Orlando, FL (United States)

2001-07-01

The Environmental Response Team (ERT) of the U.S. Environmental Protection Agency was created to provide on-site professional expertise as well as health and safety guidance to Federal on-scene coordinators during accidental oil and chemical releases. ERT provides practical technical solutions to response activities based on theory as well as actual experience. Its creation in 1978 fulfilled the requirements of the U.S. National Contingency Plan. Members of the team have developed a 40-hour Hazardous Waste Responders training course and have themselves, attended a hands-on chemical and biological warfare personnel protective clothing course provided by the U.S. Army. The course demonstrated decontamination showers, moon suits, and entry procedures to a contaminated battlefield situation. ERT continues to emphasize the importance of hands-on training and exercises. Various training programs are underway where students can learn real-time monitoring techniques and respond to simulated hazardous waste incidents. They also learn how to assess environmental, public and occupational health and safety information on the Internet. The students also run air plume models and perform wet bench chemistry experiments. With the advent of more powerful computers, the current objective is to continue with these training activities using Instructor Controlled Interactive Computer Training (ICICT).

Response to a radioactive materials release having a transboundary impact

International Nuclear Information System (INIS)

1989-01-01

Compared with an accidental release of radioactive material which is confined to the accident State, a transboundary release has added dimensions which were not fully anticipated in publications dealing with response to accidents at nuclear facilities. The new aspects to the problem may be summarized as follows: (1) A transboundary release of radioactive material, as distinct from a release which affects only the accident State, has international repercussions in the following ways: Potentially at least, the difficulties associated with a transboundary release may be magnified in those States that have no nuclear facilities of their own and may, therefore, have foreseen no need for resources to assess and deal with radioactive contamination of their food supplies, their water and their environment appropriately. International trade, in food commodities particularly, may be severely affected. Issues of compensation may arise for which the dispute settlement mechanisms are weak or non-existent. (2) Many Member States are in such geographic locations that they could be affected by a transboundary release occurring in any of their surrounding neighbour States. Planning for and responding to such an event is necessarily more difficult than planning for an accidental release from a single, identified nuclear facility. (3) Deposits of radioactive material from a distant source are apt to be highly unpredictable. Depending on weather conditions, they may be localized in a random fashion or widespread. Because of the international dimension of the problem and its essentially unpredictable character it is recommended here that planning for such events should be carried at the national or federal government level rather than at provincial government level. 14 refs

Survey of radioactive effluent releases from byproduct material facilities. Technical report

International Nuclear Information System (INIS)

Cook, J.R.

1981-08-01

A survey of over 3,000 NRC byproduct material licensees was conducted in late 1980 to collect data on annual effluent releases of radioactivity. The survey was conducted through a questionnaire, which was sent to NRC licensees who handle radioactive material in unsealed form, i.e., research, medical, and industrial institutions. Principal findings from the survey analysis are as follows: More than 98% of the reported annual releases to air (484 to 490) yield calculated average concentrations at the boundary of the unrestricted area that were at 1% or less than the maximum permissible concentration (MPC) of Appendix B, Table II, Column 1 of 10 CFR 20. The largest reported annual release was estimated to yield a concentration that was approximately 12% of MPC, the 5 other releases ranged from 1 to 10% of MPC. All reported annual releases of liquid waste were within the limits specified by NRC with most facilities reporting annual releases of only a fraction of a curie. Based on the data provided by licensees and analyzed in this report, it appears that in general the environmental impacts from research, medical and industrial institutions and organizations licensed by the NRC to possess and use byproduct materials are minimal and correspond to a small fraction of that from natural background

Method and apparatus for the management of hazardous waste material

Science.gov (United States)

Murray, Jr., Holt

1995-01-01

A container for storing hazardous waste material, particularly radioactive waste material, consists of a cylindrical body and lid of precipitation hardened C17510 beryllium-copper alloy, and a channel formed between the mated lid and body for receiving weld filler material of C17200 copper-beryllium alloy. The weld filler material has a precipitation hardening temperature lower than the aging kinetic temperature of the material of the body and lid, whereby the weld filler material is post weld heat treated for obtaining a weld having substantially the same physical, thermal, and electrical characteristics as the material of the body and lid. A mechanical seal assembly is located between an interior shoulder of the body and the bottom of the lid for providing a vacuum seal.

Iron oxide/aluminum/graphene energetic nanocomposites synthesized by atomic layer deposition: Enhanced energy release and reduced electrostatic ignition hazard

Energy Technology Data Exchange (ETDEWEB)

Yan, Ning; Qin, Lijun [Laboratory of Material Surface Engineering and Nanofabrication, Xi’an Modern Chemistry Research Institute, Shaanxi (China); Science and Technology on Combustion and Explosion Laboratory, Xi’an Modern Chemistry Research Institute, Shaanxi (China); Hao, Haixia [Science and Technology on Combustion and Explosion Laboratory, Xi’an Modern Chemistry Research Institute, Shaanxi (China); Hui, Longfei [Laboratory of Material Surface Engineering and Nanofabrication, Xi’an Modern Chemistry Research Institute, Shaanxi (China); Science and Technology on Combustion and Explosion Laboratory, Xi’an Modern Chemistry Research Institute, Shaanxi (China); Zhao, Fengqi [Science and Technology on Combustion and Explosion Laboratory, Xi’an Modern Chemistry Research Institute, Shaanxi (China); Feng, Hao, E-mail: fenghao98@hotmail.com [Laboratory of Material Surface Engineering and Nanofabrication, Xi’an Modern Chemistry Research Institute, Shaanxi (China); State Key Laboratory of Fluorine and Nitrogen Chemicals, Xi’an Modern Chemistry Research Institute, Shaanxi (China)

2017-06-30

Highlights: • Energetic rGO/Al@Fe{sub 2}O{sub 3}nanocompositeswerefabricatedbyatomiclayerdepositionapproach. • A novel Al@Fe{sub 2}O{sub 3} unit featuring core-shell structure was decorated on the graphene nanosheet. • RGO/Al@Fe{sub 2}O{sub 3} nanocomposite exhibits superior energy release and reduced electrostatic ignition hazard. - Abstract: Nanocomposites consisting of iron oxide (Fe{sub 2}O{sub 3}) and nano-sized aluminum (Al), possessing outstanding exothermic redox reaction characteristics, are highly promising nanothermite materials. However, the reactant diffusion inhibited in the solid state system makes the fast and complete energy release very challenging. In this work, Al nanoparticles anchored on graphene oxide (GO/Al) was initially prepared by a solution assembly approach. Fe{sub 2}O{sub 3} was deposited on GO/Al substrates by atomic layer deposition (ALD). Simultaneously thermal reduction of GO occurs, resulting in rGO/Al@Fe{sub 2}O{sub 3} energetic composites. Differential scanning calorimetry (DSC) analysis reveals that rGO/Al@Fe{sub 2}O{sub 3} composite containing 4.8 wt% of rGO exhibits a 50% increase of the energy release compared to the Al@Fe{sub 2}O{sub 3} nanothermite synthesized by ALD, and an increase of about 130% compared to a random mixture of rGO/Al/Fe{sub 2}O{sub 3} nanoparticles. The enhanced energy release of rGO/Al@Fe{sub 2}O{sub 3} is attributed to the improved spatial distribution as well as the increased interfacial intimacy between the oxidizer and the fuel. Moreover, the rGO/Al@Fe{sub 2}O{sub 3} composite with an rGO content of 9.6 wt% exhibits significantly reduced electrostatic discharge sensitivity. These findings may inspire potential pathways for engineering energetic nanocomposites with enhanced energy release and improved safety characteristics.

Iron oxide/aluminum/graphene energetic nanocomposites synthesized by atomic layer deposition: Enhanced energy release and reduced electrostatic ignition hazard

International Nuclear Information System (INIS)

Yan, Ning; Qin, Lijun; Hao, Haixia; Hui, Longfei; Zhao, Fengqi; Feng, Hao

2017-01-01

Highlights: • Energetic rGO/Al@Fe 2 O 3 nanocompositeswerefabricatedbyatomiclayerdepositionapproach. • A novel Al@Fe 2 O 3 unit featuring core-shell structure was decorated on the graphene nanosheet. • RGO/Al@Fe 2 O 3 nanocomposite exhibits superior energy release and reduced electrostatic ignition hazard. - Abstract: Nanocomposites consisting of iron oxide (Fe 2 O 3 ) and nano-sized aluminum (Al), possessing outstanding exothermic redox reaction characteristics, are highly promising nanothermite materials. However, the reactant diffusion inhibited in the solid state system makes the fast and complete energy release very challenging. In this work, Al nanoparticles anchored on graphene oxide (GO/Al) was initially prepared by a solution assembly approach. Fe 2 O 3 was deposited on GO/Al substrates by atomic layer deposition (ALD). Simultaneously thermal reduction of GO occurs, resulting in rGO/Al@Fe 2 O 3 energetic composites. Differential scanning calorimetry (DSC) analysis reveals that rGO/Al@Fe 2 O 3 composite containing 4.8 wt% of rGO exhibits a 50% increase of the energy release compared to the Al@Fe 2 O 3 nanothermite synthesized by ALD, and an increase of about 130% compared to a random mixture of rGO/Al/Fe 2 O 3 nanoparticles. The enhanced energy release of rGO/Al@Fe 2 O 3 is attributed to the improved spatial distribution as well as the increased interfacial intimacy between the oxidizer and the fuel. Moreover, the rGO/Al@Fe 2 O 3 composite with an rGO content of 9.6 wt% exhibits significantly reduced electrostatic discharge sensitivity. These findings may inspire potential pathways for engineering energetic nanocomposites with enhanced energy release and improved safety characteristics.

K Basins fuel encapsulation and storage hazard categorization

International Nuclear Information System (INIS)

Porten, D.R.

1994-12-01

This document establishes the initial hazard categorization for K-Basin fuel encapsulation and storage in the 100 K Area of the Hanford site. The Hazard Categorization for K-Basins addresses the potential for release of radioactive and non-radioactive hazardous material located in the K-Basins and their supporting facilities. The Hazard Categorization covers the hazards associated with normal K-Basin fuel storage and handling operations, fuel encapsulation, sludge encapsulation, and canister clean-up and disposal. The criteria categorizes a facility based on total curies per radionuclide located in the facility. Tables 5-3 and 5-4 display the results in section 5.0. In accordance with DOE-STD-1027 and the analysis provided in section 5.0, the K East Basin fuel encapsulation and storage activity and the K West Basin storage are classified as a open-quotes Category 2close quotes Facility

Functionalized mesoporous materials for adsorption and release of different drug molecules: A comparative study

International Nuclear Information System (INIS)

Wang Gang; Otuonye, Amy N.; Blair, Elizabeth A.; Denton, Kelley; Tao Zhimin; Asefa, Tewodros

2009-01-01

The adsorption capacity and release properties of mesoporous materials for drug molecules can be improved by functionalizing their surfaces with judiciously chosen organic groups. Functionalized ordered mesoporous materials containing various types of organic groups via a co-condensation synthetic method from 15% organosilane and by post-grafting organosilanes onto a pre-made mesoporous silica were synthesized. Comparative studies of their adsorption and release properties for various model drug molecules were then conducted. Functional groups including 3-aminopropyl, 3-mercaptopropyl, vinyl, and secondary amine groups were used to functionalize the mesoporous materials while rhodamine 6G and ibuprofen were utilized to investigate the materials' relative adsorption and release properties. The self-assembly of the mesoporous materials was carried out in the presence of cetyltrimethylammonium bromide (CTAB) surfactant, which produced MCM-41 type materials with pore diameters of ∼2.7-3.3 nm and moderate to high surface areas up to ∼1000 m 2 /g. The different functional groups introduced into the materials dictated their adsorption capacity and release properties. While mercaptopropyl and vinyl functionalized samples showed high adsorption capacity for rhodamine 6G, amine functionalized samples exhibited higher adsorption capacity for ibuprofen. While the diffusional release of ibuprofen was fitted on the Fickian diffusion model, the release of rhodamine 6G followed Super Case-II transport model. - Graphical abstract: The adsorption capacity and release properties of mesoporous materials for various drug molecules are tuned by functionalizing the surfaces of the materials with judiciously chosen organic groups. This work reports comparative studies of the adsorption and release properties of functionalized ordered mesoporous materials containing different hydrophobic and hydrophilic groups that are synthesized via a co-condensation and post-grafting methods for

Hazardous Materials Management and Emergency Response training Center needs assessment

International Nuclear Information System (INIS)

McGinnis, K.A.; Bolton, P.A.; Robinson, R.K.

1993-09-01

For the Hanford Site to provide high-quality training using simulated job-site situations to prepare the 4,000 Site workers and 500 emergency responders for known and unknown hazards a Hazardous Materials Management and Emergency Response Training Center is needed. The center will focus on providing classroom lecture as well as hands-on, realistic training. The establishment of the center will create a partnership among the US Department of Energy; its contractors; labor; local, state, and tribal governments; and Xavier and Tulane Universities of Louisiana. This report presents the background, history, need, benefits, and associated costs of the proposed center

Natural radioactivity level and radiological hazard assessment of commonly used building material in Xining, China

International Nuclear Information System (INIS)

Shigang Chao; Xinwei Lu; Mengmeng Zhang; Long Pang

2014-01-01

Natural radioactivity of the commonly used building materials in Xining of China was measured using gamma-ray spectrometer system comprising a NaI(Tl) detector. Radioactivity concentrations of 226 Ra, 232 Th and 40 K in the studied samples range from 11.6 to 120.6, 10.2 to 107.1 and 228.0 to 1,036.2 Bq kg -1 , respectively. The concentrations for these natural radionuclides were compared with the reported data of other countries and the mean value for soil. Radium equivalent activity, indoor air absorbed dose rate, annual effective dose rate as well as external and internal hazard indices were calculated to assess radiological hazards for people living in dwelling made of the building materials. The radiological hazard assessment results show that the studied building materials, except for some aerated concrete block samples, are safe for use in construction of dwellings in the study area and do not pose any significant source of radiation hazard. (author)

Operators guide: Atmospheric Release Advisory Capability (ARAC) site facility

International Nuclear Information System (INIS)

Lawver, B.S.

1977-01-01

In this report capabilities and services are described for the Atmospheric Release Advisory Capability (ARAC). The ARAC site system and its operating procedures and interactions with the ARAC central facility located at LLL is outlined. ARAC is designed to help officials at designated ERDA sites and other locations in estimating the effects of atmospheric releases of radionuclides or other hazardous materials by issuing real-time advisories to guide them in their planning

Operators guide: Atmospheric Release Advisory Capability (ARAC) site facility

International Nuclear Information System (INIS)

Cassaro, E.; Lomonaco, L.

1979-01-01

The Atmospheric Release Advisory Capability (ARAC) is designed to help officials at designated DOE sites and other locations in estimating the effects of atmospheric releases of radionuclides or other hazardous materials by issuing real-time advisories to guide them in their planning. This report outlines the capabilities and sources of ARAC, and in more detail describes an ARAC Site Facility, its operating procedures and interactions with the ARAC Central Facility (ACF) located at LLL

Hazardous materials emergency response training program at Texas A ampersand M University

International Nuclear Information System (INIS)

Stirling, A.G.

1989-01-01

The Texas Engineering Extension Service (TEEX) as the engineering vocational training arm of the Texas A ampersand M University system has conducted oil-spill, hazardous-material, and related safety training for industry since 1976 and fire suppression training since 1931. In 1987 TEEX conducted training for some 66,000 persons, of which some 6000 were in hazardous-materials safety training and 22,000 in fire suppression or related fields. Various laws and regulations exist relative to employee training at an industrial facility, such as the Hazard Communication Act, the Resource Conservation and Recovery Act (RCRA), the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA or more commonly Superfund), the Community Right to Know Law, and the Superfund Amendments and Reauthorization Act (SARA), Titles I and III. The TEEX programs developed on the foundation emphasize the hands-on approach (60% field exercises) to provide a comprehensive training curriculum resulting in regulatory compliance, an effective emergency response capability, a prepared community, and a safe work environment

Technical Guidance for Hazardous Analysis, Emergency Planning for Extremely Hazardous Substances

Science.gov (United States)

This current guide supplements NRT-1 by providing technical assistance to LEPCs to assess the lethal hazards related to potential airborne releases of extremely hazardous substances (EHSs) as designated under Section 302 of Title Ill of SARA.

Tritium release from lithium titanate, a low-activation tritium breeding material

International Nuclear Information System (INIS)

Kopasz, J.P.; Miller, J.M.; Johnson, C.E.

1994-01-01

The goals for fusion power are to produce energy in as safe, economical, and environmentally benign a manner as possible. To ensure environmentally sound operation low-activation materials should be used where feasible. The ARIES Tokamak Reactor Study has based reactor designs on the concept of using low-activation materials throughout the fusion reactor. For the tritium breeding blanket, the choices for low activation tritium breeding materials are limited. Lithium titanate is an alternative low-activation ceramic material for use in the tritium breeding blanket. To date, very little work has been done on characterizing the tritium release for lithium titanate. We have thus performed laboratory studies of tritium release from irradiated lithium titanate. The results indicate that tritium is easily removed from lithium titanate at temperatures as low as 600 K. The method of titanate preparation was found to affect the tritium release, and the addition of 0.1% H 2 to the helium purge gas did not improve tritium recovery. ((orig.))

Some relevant parameters for assessing fire hazards of combustible mine materials using laboratory scale experiments.

Science.gov (United States)

Litton, Charles D; Perera, Inoka E; Harteis, Samuel P; Teacoach, Kara A; DeRosa, Maria I; Thomas, Richard A; Smith, Alex C

2018-04-15

When combustible materials ignite and burn, the potential for fire growth and flame spread represents an obvious hazard, but during these processes of ignition and flaming, other life hazards present themselves and should be included to ensure an effective overall analysis of the relevant fire hazards. In particular, the gases and smoke produced both during the smoldering stages of fires leading to ignition and during the advanced flaming stages of a developing fire serve to contaminate the surrounding atmosphere, potentially producing elevated levels of toxicity and high levels of smoke obscuration that render the environment untenable. In underground mines, these hazards may be exacerbated by the existing forced ventilation that can carry the gases and smoke to locations far-removed from the fire location. Clearly, materials that require high temperatures (above 1400 K) and that exhibit low mass loss during thermal decomposition, or that require high heat fluxes or heat transfer rates to ignite represent less of a hazard than materials that decompose at low temperatures or ignite at low levels of heat flux. In order to define and quantify some possible parameters that can be used to assess these hazards, small-scale laboratory experiments were conducted in a number of configurations to measure: 1) the toxic gases and smoke produced both during non-flaming and flaming combustion; 2) mass loss rates as a function of temperature to determine ease of thermal decomposition; and 3) mass loss rates and times to ignition as a function of incident heat flux. This paper describes the experiments that were conducted, their results, and the development of a set of parameters that could possibly be used to assess the overall fire hazard of combustible materials using small scale laboratory experiments.

78 FR 69745 - Safety and Security Plans for Class 3 Hazardous Materials Transported by Rail

Science.gov (United States)

2013-11-20

... material (considering the material's underlying chemical properties, corrosivity, and other characteristics) is fundamental to ensuring the selection of proper packaging and that the hazards of the materials...

Experiments to quantify airborne release from packages with dispersible radioactive materials under accident conditions

Energy Technology Data Exchange (ETDEWEB)

Martens, R.; Lange, F. [Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) mbH, Schwertnergasse 1, 50667 Koeln (Germany); Koch, W.; Nolte, O. [Fraunhofer-Institut fuer Toxikologie und Experimentelle Medizin (ITEM), Nikolai-Fuchs-Str.1, 30625 Hannover (Germany)

2005-07-01

For transport or handling accidents involving packages with radioactive materials and the assessment of potential radiological consequences, for the review of current requirements of the IAEA Transport Regulations, and for their possible further development reliable release data following mechanical impact are required. Within this context a research project was carried out which extends the basis for a well-founded examination of the contemporary system of requirements of 'Low Specific Activity' (LSA)-type materials and allows for its further development where appropriate. This project comprises a prior system-analytical examination and an experimental programme aiming at improving the general physical understanding of the release process as well as the quantity and the characteristics of airborne released material for non-fixed dispersible LSA-II material upon mechanical impact. Impaction experiments applying small, medium and real sized specimens of different dispersible materials revealed that the release behaviour of dispersible powders strongly depends upon material properties, e.g. particle size distribution and cohesion forces. The highest experimentally determined release fraction of respirable mass (AED < 10 {mu}m) amounted to about 2 % and was obtained for 2 kg of un-contained easily dispersible pulverized fly ash (PFA). For larger un-contained PFA specimen the release fraction decreases. However, packaging containing powdery material substantially reduces the airborne release fraction. The measured airborne release fractions for a 200 l drum with Type A certificate containing PFA were about a factor of 50 to 100 lower than for un-contained material. For a drop height of 9 m the airborne release fraction amounted to about 4 x 10{sup -5}. This value should be applicable for most of transport and handling accidents with mechanical impact. For a metal container of Type IP-2 or better which contains powder masses of 100 kg or more this release

Performance-oriented packagings for hazardous materials: Resource guide

Energy Technology Data Exchange (ETDEWEB)

1993-09-01

This document provides recommendations to US Department of Energy (DOE) shippers regarding packaging that meet performance-oriented packaging requirements implemented by US Department of Transportation (DOT) in rulemaking HM-181 (December 21, 1990) and subsequent actions. The packaging described in this document are certified by their vendor to comply with requirements for Packing Group I, II, or III hazardous materials packaging. The intent of this document is to share information between DOE and contractors and at all DOE facilities.

Performance-oriented packagings for hazardous materials: Resource guide

International Nuclear Information System (INIS)

1993-09-01

This document provides recommendations to US Department of Energy (DOE) shippers regarding packaging that meet performance-oriented packaging requirements implemented by US Department of Transportation (DOT) in rulemaking HM-181 (December 21, 1990) and subsequent actions. The packaging described in this document are certified by their vendor to comply with requirements for Packing Group I, II, or III hazardous materials packaging. The intent of this document is to share information between DOE and contractors and at all DOE facilities

Influences of use activities and waste management on environmental releases of engineered nanomaterials

International Nuclear Information System (INIS)

Wigger, Henning; Hackmann, Stephan; Zimmermann, Till; Köser, Jan; Thöming, Jorg; Gleich, Arnim von

2015-01-01

Engineered nanomaterials (ENM) offer enhanced or new functionalities and properties that are used in various products. This also entails potential environmental risks in terms of hazard and exposure. However, hazard and exposure assessment for ENM still suffer from insufficient knowledge particularly for product-related releases and environmental fate and behavior. This study therefore analyzes the multiple impacts of the product use, the properties of the matrix material, and the related waste management system (WMS) on the predicted environmental concentration (PEC) by applying nine prospective life cycle release scenarios based on reasonable assumptions. The products studied here are clothing textiles treated with silver nanoparticles (AgNPs), since they constitute a controversial application. Surprisingly, the results show counter-intuitive increases by a factor of 2.6 in PEC values for the air compartment in minimal AgNP release scenarios. Also, air releases can shift from washing to wearing activity; their associated release points may shift accordingly, potentially altering release hot spots. Additionally, at end-of-life, the fraction of AgNP-residues contained on exported textiles can be increased by 350% when assuming short product lifespans and globalized WMS. It becomes evident that certain combinations of use activities, matrix material characteristics, and WMS can influence the regional PEC by several orders of magnitude. Thus, in the light of the findings and expected ENM market potential, future assessments should consider these aspects to derive precautionary design alternatives and to enable prospective global and regional risk assessments. - Highlights: • Textile use activities and two waste management systems (WMSs) are investigated. • Matrix material and use activities determine the ENM release. • Counter-intuitive shifts of releases to air can happen during usage. • WMS export can increase by 350% in case of short service life and

Influences of use activities and waste management on environmental releases of engineered nanomaterials

Energy Technology Data Exchange (ETDEWEB)

Wigger, Henning, E-mail: hwigger@uni-bremen.de [Faculty of Production Engineering, Department of Technological Design and Development, University of Bremen, Badgasteiner Str. 1, 28359 Bremen (Germany); Hackmann, Stephan [UFT Center for Environmental Research and Sustainable Technology, Department of General and Theoretical Ecology, University of Bremen, Leobener Str., 28359 Bremen (Germany); Zimmermann, Till [Faculty of Production Engineering, Department of Technological Design and Development, University of Bremen, Badgasteiner Str. 1, 28359 Bremen (Germany); ARTEC — Research Center for Sustainability Studies, Enrique-Schmidt-Str. 7, 28359 Bremen (Germany); Köser, Jan [UFT Center for Environmental Research and Sustainable Technology, Department of Sustainable Chemistry, University of Bremen, Leobener Str., 28359 Bremen (Germany); Thöming, Jorg [UFT Center for Environmental Research and Sustainable Technology, Department of Sustainable Chemical Engineering, University of Bremen, Leobener Str., 28359 Bremen (Germany); Gleich, Arnim von [Faculty of Production Engineering, Department of Technological Design and Development, University of Bremen, Badgasteiner Str. 1, 28359 Bremen (Germany); ARTEC — Research Center for Sustainability Studies, Enrique-Schmidt-Str. 7, 28359 Bremen (Germany)

2015-12-01

Engineered nanomaterials (ENM) offer enhanced or new functionalities and properties that are used in various products. This also entails potential environmental risks in terms of hazard and exposure. However, hazard and exposure assessment for ENM still suffer from insufficient knowledge particularly for product-related releases and environmental fate and behavior. This study therefore analyzes the multiple impacts of the product use, the properties of the matrix material, and the related waste management system (WMS) on the predicted environmental concentration (PEC) by applying nine prospective life cycle release scenarios based on reasonable assumptions. The products studied here are clothing textiles treated with silver nanoparticles (AgNPs), since they constitute a controversial application. Surprisingly, the results show counter-intuitive increases by a factor of 2.6 in PEC values for the air compartment in minimal AgNP release scenarios. Also, air releases can shift from washing to wearing activity; their associated release points may shift accordingly, potentially altering release hot spots. Additionally, at end-of-life, the fraction of AgNP-residues contained on exported textiles can be increased by 350% when assuming short product lifespans and globalized WMS. It becomes evident that certain combinations of use activities, matrix material characteristics, and WMS can influence the regional PEC by several orders of magnitude. Thus, in the light of the findings and expected ENM market potential, future assessments should consider these aspects to derive precautionary design alternatives and to enable prospective global and regional risk assessments. - Highlights: • Textile use activities and two waste management systems (WMSs) are investigated. • Matrix material and use activities determine the ENM release. • Counter-intuitive shifts of releases to air can happen during usage. • WMS export can increase by 350% in case of short service life and

Radioactive materials released from nuclear power plants. Annual report 1977

International Nuclear Information System (INIS)

Decker, T.R.

1978-11-01

Releases of radioactive materials in airborne and liquid effluents from commercial light water reactors during 1977 have been compiled and reported. Data on solid waste shipments as well as selected operating information have been included. This report supplements earlier annual reports issued by the former Atomic Energy Commission and the Nuclear Regulatory Commission. The 1977 release data are compared with previous years releases in tabular form. Data covering specific radionuclides are summarized

Results of development and field tests of a radar-tracer system providing meteorological support to modeling hazardous technological releases

International Nuclear Information System (INIS)

Shershakov, V.M.; Zukov, G.P.; Kosykh, V.S.

2003-01-01

radiation monitoring laboratory and the LDU was on the bank of the cooling pond. The main characteristics of a cloud of substances are standard deviations in the spatial concentration distributions in the cloud along mutually perpendicular directions, which are representative spatial scales of the cloud in these directions. The squares of these values are relative variances of the cloud. These characteristics were the first to determine and are among the most important input parameters in different models assessing transport and dispersion of hazardous substances. Dispersion of a cloud of substances is influenced by turbulence and vertical shifts of the mean wind speed, with the patterns of dispersion being different depending an diffusion time (or distance to a source). The results of the conducted experiments have revealed an important advantage of the used radar complex in terms of support to predictions of possible contamination in case of release of hazardous materials. As the chaff cloud moves with the wind and is dispersed, it echoes the meteorological situation at a given time moment (vertical wind distribution and air temperature, turbulence level, boundary layer thickness, type of underlying surface) and any changes occurring in the conditions on its way. Based on obtained radar data, the radar complex is capable of assessing the dispersion parameters which can then be used in the mathematical transport and dispersion models. What's more, determination of these parameters does not require any meteorological measurements. In addition, using data about movement of the cloud centroid, the wind speed and direction is estimated at the release height by the radar complex itself. The conducted experiments have shown that the developed technology makes possible measuring key parameters of a cloud of substances at the height of dispersion and taking into account local features of the distribution of meteorological quantities occurring in the vicinity of a source. This

Impacts on health and safety from transfer/consolidation of nuclear materials and hazardous chemicals

International Nuclear Information System (INIS)

Gallucci, R.H.V.

1994-11-01

Environmental restoration plans at the US Department of Energy (USDOE) Hanford Site calls for transfer/consolidation of ''targets/threats,'' namely nuclear materials and hazardous chemicals. Reductions in the health and safety hazards will depend on the plans implemented. Pacific Northwest Laboratory (PNL) estimated these potential impacts, assuming implementation of the current reference plan and employing ongoing risk and safety analyses. The results indicated the potential for ''significant'' reductions in health and safety hazards in the long term (> 25 years) and a potentially ''noteworthy'' reduction in health hazard in the short term (≤ 25 years)

Fluoride release and recharge abilities of contemporary fluoride-containing restorative materials and dental adhesives.

Science.gov (United States)

Dionysopoulos, Dimitrios; Koliniotou-Koumpia, Eugenia; Helvatzoglou-Antoniades, Maria; Kotsanos, Nikolaos

2013-01-01

The aim of this study was to evaluate the fluoride release of five fluoride-releasing restorative materials and three dental adhesives, before and after NaF solution treatment. Five restorative materials (Fuji IX GP, GC Corp.; Ketac N100, 3M ESPE; Dyract Extra, Dentsply; Beautifil II, Shofu Inc.; Wave, SDI) and three dental adhesives (Stae, SDI; Fluorobond II - Shofu Inc.; Prime & Bond NT, Dentsply) were investigated before and after NaF solution treatment. A fluoride ion-selective electrode was to measure fluoride concentrations. During the 86-day period before NaF solution treatment, Fuji IX GP released the highest amount of fluoride among the restorative materials while Prime & Bond NT was the highest among the dental adhesives. After NaF solution treatment, Fuji IX GP again ranked the highest in fluoride release among the restorative materials while Fluorobond II ranked the highest among dental adhesives. It was concluded that the compositions and setting mechanisms of fluoride-containing dental materials influenced their fluoride release and recharge abilities.

National Atmospheric Release Advisory Center (NARAC) Capabilities for Homeland Security

Energy Technology Data Exchange (ETDEWEB)

Sugiyama, G; Nasstrom, J; Baskett, R; Simpson, M

2010-03-08

The Department of Energy's National Atmospheric Release Advisory Center (NARAC) provides critical information during hazardous airborne releases as part of an integrated national preparedness and response strategy. Located at Lawrence Livermore National Laboratory, NARAC provides 24/7 tools and expert services to map the spread of hazardous material accidentally or intentionally released into the atmosphere. NARAC graphical products show affected areas and populations, potential casualties, and health effect or protective action guideline levels. LLNL experts produce quality-assured analyses based on field data to assist decision makers and responders. NARAC staff and collaborators conduct research and development into new science, tools, capabilities, and technologies in strategically important areas related to airborne transport and fate modeling and emergency response. This paper provides a brief overview of some of NARAC's activities, capabilities, and research and development.

Analysis on the Industrial Design of Food Package and the Component of Hazardous Substance in the Packaging Material

OpenAIRE

Wei-Wen Huang

2015-01-01

Transferring the hazardous chemicals contained in food packaging materials into food would threaten the health of consumers, therefore, the related laws and regulations and the detection method of hazardous substance have been established at home and abroad to ensure the safety to use the food packaging material. According to the analysis on the hazardous component in the food packaging, a set of detection methods for hazardous substance in the food packaging was established in the paper and ...

77 FR 36607 - Office of Hazardous Materials Safety Notice of Applications for Modification of Special Permit

Science.gov (United States)

2012-06-19

... modification of special permits (e.g. to provide for additional hazardous materials, packaging design changes... hazardous materials. 12102-M EQ Industrial 49 CFR 173.56(i); To modify the special Services, Inc. 173.56(b... 4.1. 13102-M Robertshaw Industrial 49 CFR 173.150(b); To modify the special Products dba 173.222(c...

Determination of fungal spore release from wet building materials

DEFF Research Database (Denmark)

Kildesø, J.; Wurtz, H.; Nielsen, Kristian Fog

2003-01-01

The release and transport of fungal spores from water-damaged building materials is a key factor for understanding the exposure to particles of fungal origin as a possible cause of adverse health effects associated to growth of fungi indoors. In this study, the release of spores from nine species...... of typical indoor fungi has been measured under controlled conditions. The fungi were cultivated for a period of 4-6 weeks on sterilized wet wallpapered gypsum boards at a relative humidity (RH) of approximately 97%. A specially designed small chamber (P-FLEC) was placed on the gypsum board. The release...

In Vitro Inhibition of Enamel Demineralisation by Fluoride-releasing Restorative Materials and Dental Adhesives.

Science.gov (United States)

Dionysopoulos, Dimitrios; Koliniotou-Koumpia, Eugenia; Helvatzoglou-Antoniades, Maria; Kotsanos, Nikolaos

2016-01-01

To determine the ability of 5 contemporary fluoride-releasing restoratives and 3 fluoride-releasing adhesives to inhibit enamel demineralisation surrounding restorations, and the associations between inhibition and the levels of fluoride released from these materials. Five fluoride-releasing restoratives (Fuji IX GP, Ketac N100, Dyract Extra, Beautifil II and Wave) and 3 fluoride-releasing adhesives (Stae, Prime & Bond NT and Fluoro Bond II) were investigated. Eight disks of each material were prepared. Fluoride release was measured daily using a fluoride-ion-selective electrode for 15 days. Twenty-four cavities for each group were restored with a restorative and an adhesive. Specimens were subjected to thermal stress and stored for 30 days in saline solution. After a 15-day pH-cycling regimen, two 150-μm-thick sections were derived from each specimen. Enamel lesion depth was measured at 0, 100, and 200 μm from each restoration's margin via polarised light microscopy. Of the restoratives investigated, Fuji IX GP released the most fluoride. The fluoride-releasing restoratives tested exhibited shallower enamel lesions than did the control group at all distances tested (p < 0.05). Fuji IX GP yielded significantly lower enamel lesion depth than did the other experimental materials. The depths of enamel lesions did not differ significantly when comparing restoratives applied with a fluoride-releasing adhesive with those applied with a non-fluoride-releasing adhesive. The fluoride-releasing materials tested reduced enamel demineralisation but to different extents, depending on their levels of fluoride release. Fluoride-releasing adhesives did not influence enamel lesion formation.

Natural radioactivity in some building materials and assessment of the associated radiation hazards

Energy Technology Data Exchange (ETDEWEB)

Kasumovic, Amira; Hankic, Ema; Kasic, Amela; Adrovic, Feriz [Tuzla Univ. (Bosnia and Herzegovina). Dept. of Physics

2018-04-01

The results of the specific activities of {sup 232}Th, {sup 226}Ra and {sup 40}K measured in samples of commonly used building materials in Bosnia and Herzegovina are presented. Measurements were performed by gamma-ray spectrometer with coaxial HPGe detector. The surface radon exhalation and mass exhalation rates for selected building materials were also measured. The determined values of specific activities were in range from 3.16 ± 0.81 Bq kg{sup -1} to 64.79 ± 6.16 Bq kg{sup -1} for {sup 232}Th, from 2.46 ± 0.95 Bq kg{sup -1} to 53.89 ± 3.67 Bq kg{sup -1} for {sup 226}Ra and from 28.44 ± 7.28 Bq kg{sup -1} to 557.30 ± 93.38 Bq kg{sup -1} for {sup 40}K. The radium equivalent activity, the activity concentration index, the external and internal hazard indices as well as the absorbed dose rate in indoor air and the corresponding annual effective dose, due to gamma-ray emission from the radioactive nuclides in the building material, were evaluated in order to assess the radiation hazards for people. The measured specific activities of the natural radioactive nuclides in all investigated building materials were compared with the published results for building materials from other European countries. It can be noted that the results from this study are similar to the data for building materials from neighbouring countries and for building materials used in the EU Member States. The radiological hazard parameters of the building materials were all within the recommended limits for safety use.

An integrated risk communication system for the transport of hazardous materials

International Nuclear Information System (INIS)

Minor, J.W. IV; Abkowitz, M.D.

2004-01-01

This paper describes the development and implementation of the prototype of an an internet-based, risk communication system prototype for the transport of hazardous materials. The system was designed with the objectives of: (1) incorporating functionality and features that are useful for meeting a variety of risk communication needs, and (2) demonstrating a high degree of interaction among system components, enabling customisation to meet the specific transport risk communication needs requirements of the host organisation. To demonstrate 'proof of concept', the system is applied to two scenarios: 1) building knowledge and awareness, focusing on how information can be entered, organised and disseminated to the public and other transport stakeholders, and 2) emergency management, utilising the system for securely managing information in responding to a transport incident involving hazardous materials transport incident. The effectiveness of the system in these applications is subsequently discussed. (author)

Hazardous Substance Release Reporting Under CERCLA, EPCR {section}304 and DOE Emergency Management System (EMS) and DOE Occurrence Reporting Requirements. Environmental Guidance

Energy Technology Data Exchange (ETDEWEB)

Traceski, T.T.

1994-06-01

Releases of various substances from DOE facilities may be subject to reporting requirements under the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) and the Emergency Planning and Community Right-to-Know Act (EPCRA), as well as DOE`s internal ``Occurrence Reporting and Processing of Operations Information`` and the ``Emergency Management System`` (EMS). CERCLA and EPCPA are Federal laws that require immediate reporting of a release of a Hazardous Substance (HS) and an Extremely Hazardous Substance (EHS), respectively, in a Reportable Quantity (RQ) or more within a 24-hour period. This guidance uses a flowchart, supplemental information, and tables to provide an overview of the process to be followed, and more detailed explanations of the actions that must be performed, when chemical releases of HSs, EHSs, pollutants, or contaminants occur at DOE facilities. This guidance should be used in conjunction with, rather than in lieu of, applicable laws, regulations, and DOE Orders. Relevant laws, regulations, and DOE Orders are referenced throughout this guidance.

Determination of the long-term release of metal(loid)s from construction materials using DGTs.

Science.gov (United States)

Schmukat, A; Duester, L; Ecker, D; Heininger, P; Ternes, T A

2013-09-15

Long-term leaching experiments are crucial to estimate the potential release of dangerous substances from construction materials. The application of Diffuse Gradients in Thin film (DGT) in static-batch experiments was tested to study the long-term release of metal(loid)s from construction materials for hydraulic engineering, for half a year. Long-term release experiments are essential to improve calculations of the life-time release for this materials. DGTs in batch experiments were found to be a space and labour efficient application, which enabled (i) to study, in a non-invasive manner, the total release of nine metal(loid)s for half a year, (ii) to differentiate between release mechanisms and (iii) to study mechanisms which were contrary to the release or caused experimental artefacts in the batch experiments. For copper slag (test material) it was found that eight metal(loid)s were released over the whole time period of 184 d. Cu, Ni and Pb were found to be released, predominantly caused by (the) weathering of sulphide minerals. Only for Zn a surface depletion mechanism was identified. The results from the long-term batch experiments deliver new information on the release of metal(loid)s during the life cycle of construction materials with regard to river basin management objectives. Copyright © 2013 Elsevier B.V. All rights reserved.

The transportation of hazardous materials

International Nuclear Information System (INIS)

Hillman, J.C.

1981-04-01

The increasing use of dangerous chemicals and petroleum products by S.A. industry makes it necessary for some form of control to be introduced to regulate the transport of these materials before a major disaster occurs, such as has occurred overseas. This report examines all the aspects that could increase the likelihood of such a disaster occurring, including the preparedness of emergency services. It also recommends the improvements or changes required to minimize this possibility. It is apparent that the training and ability of vehicle drivers are key areas in this respect and they are discussed at length. Forthcoming regulations under the Hazardous Substances Act No. 15 of 1973 are examined and the effects of over-restrictive legislation considered. The report concludes that legislation promulgated gradually to reinforce voluntary industrial practices will ultimately restrict this type of transport to the safety-conscious and competent operator, therefore minimizing the risk as much as possible

Risk assessment methodology for evaluating releases of radioactively contaminated materials

International Nuclear Information System (INIS)

Chen, S.Y.

1993-01-01

Extensive decontamination and decommissioning (D ampersand D) activities are expected to be required in the near future in association with license termination of nuclear power facilities and cleanup efforts at the U.S. Department of Energy's (DOE's) weapons production facilities. In advance of these D ampersand D activities, it is becoming increasingly urgent that standards be established for the release of materials with residual radioactive contamination. The only standards for unrestricted release that currently exist address surface contamination. The methods used to justify those standards were developed some 20 yr ago and may not satisfy today's criteria. Furthermore, the basis of setting standards has moved away from the traditional open-quotes instrumentation-basedclose quotes concept toward a open-quotes risk-basedclose quotes approach. Therefore, as new release standards are developed, it will be necessary that risk assessment methodology consistent with modern concepts be incorporated into the process. This paper discusses recent developments in risk methodology and issues and concerns regarding the future development of standards for the release of radioactively contaminated materials

Integrating Hazardous Materials Characterization and Assessment Tools to Guide Pollution Prevention in Electronic Products and Manufacturing

Science.gov (United States)

Lam, Carl

Due to technology proliferation, the environmental burden attributed to the production, use, and disposal of hazardous materials in electronics have become a worldwide concern. The major theme of this dissertation is to develop and apply hazardous materials assessment tools to systematically guide pollution prevention opportunities in the context of electronic product design, manufacturing and end-of-life waste management. To this extent, a comprehensive review is first provided on describing hazard traits and current assessment methods to evaluate hazardous materials. As a case study at the manufacturing level, life cycle impact assessment (LCIA)-based and risk-based screening methods are used to quantify chemical and geographic environmental impacts in the U.S. printed wiring board (PWB) industry. Results from this industrial assessment clarify priority waste streams and States to most effectively mitigate impact. With further knowledge of PWB manufacturing processes, select alternative chemical processes (e.g., spent copper etchant recovery) and material options (e.g., lead-free etch resist) are discussed. In addition, an investigation on technology transition effects for computers and televisions in the U.S. market is performed by linking dynamic materials flow and environmental assessment models. The analysis forecasts quantities of waste units generated and maps shifts in environmental impact potentials associated with metal composition changes due to product substitutions. This insight is important to understand the timing and waste quantities expected and the emerging toxic elements needed to be addressed as a consequence of technology transition. At the product level, electronic utility meter devices are evaluated to eliminate hazardous materials within product components. Development and application of a component Toxic Potential Indicator (TPI) assessment methodology highlights priority components requiring material alternatives. Alternative

An Exercise in Using the U.S. Environmental Protection Agency's Hazard Ranking System: A Simulation. Grades 8-12.

Science.gov (United States)

HAZWRAP, The Hazardous Waste Remedial Actions Program.

The educational objective of this exercise is for students to use a risk assessment tool to evaluate a hazardous release site and for students in grades 8-12 to increase their experience with geology, aquifers, soils, land use, pollution, data analysis, and map concepts. Students use background information on hazardous materials, the Environmental…

Controlling Object Heat Release Rate using Geometrical Features

OpenAIRE

Kraft, Stefan Marc

2017-01-01

An experimental study was conducted to determine the effect of complex geometries on the burning rate of materials made using additive manufacturing. Controlling heat release rate has applicability in limiting fire hazards as well as for designing fuels for optimal burning rate. The burning rate of a structure is a function of the material properties as well as the airflow through it, which is dictated by the geometry. This burning rate is generally proportional to the porosity for obj...

Route selection for the transport of hazardous materials

Energy Technology Data Exchange (ETDEWEB)

Seiler, F A

1988-12-01

The factors governing the risk-weighted selection of routes for transport of hazardous materials are analyzed. Starting from a formulation for the total risk of these transports that assumes complete information, approximations for the more realistic case of partial and uncertain information are discussed. These approximations involve well-known risk assessment techniques and mathematical methods; among the latter, Monte Carlo calculations hold the most promise. The actual route selection is based on an index of total societal cost, evaluated for a set of potential routes. (author)

Assessment of natural radioactivity and radiological hazards in building materials used in Yan'an, China.

Science.gov (United States)

Lu, Xinwei; Li, Nan; Yang, Guang; Zhao, Caifeng

2013-03-01

The concentration of natural radionuclides in commonly used building materials collected from Yan'an, China, was determined using gamma ray spectroscopy with a NaI(Tl) detector. The activity concentration of ²²⁶Ra, ²³²Th, and ⁴⁰K in the studied building materials ranges from 9.4-73.1, 11.5-86.9, and 258.9-1,055.1 Bq kg⁻¹, respectively. The concentrations for these natural radionuclides were compared with the reported data of other countries and the world mean values for soil. The radium equivalent activity (Raeq), external hazard index (Hex), internal hazard index (Hin), indoor air absorbed dose rate, and annual effective dose rate due to natural radionuclides in samples were estimated to assess radiological hazards for people living in dwellings made of the studied building materials. The calculated Raeq values of all building materials (75.7-222.1 Bq kg⁻¹) are lower than the limit of 370 Bq kg⁻¹. The values of Hex and Hin are less than unity. The mean values of indoor air absorbed dose rates of all building materials (101.0 ± 14.1-177.0 ± 6.8 nGy h⁻¹) are higher than the world population-weighted average of 84 nGy h⁻¹, while the mean values of annual effective dose range from 0.50 ± 0.07-0.87 ± 0.03 mSv y⁻¹, which are lower than the recommended limit of 1 mSv y⁻¹. It is found that these materials may be used safely as construction materials and do not pose significant radiation hazards to inhabitants.

Methodology of external exposure calculation for reuse of conditional released materials from decommissioning - 59138

International Nuclear Information System (INIS)

Ondra, Frantisek; Vasko, Marek; Necas, Vladimir

2012-01-01

The article presents methodology of external exposure calculation for reuse of conditional released materials from decommissioning using VISIPLAN 3D ALARA planning tool. Production of rails has been used as an example application of proposed methodology within the CONRELMAT project. The article presents a methodology for determination of radiological, material, organizational and other conditions for conditionally released materials reuse to ensure that workers and public exposure does not breach the exposure limits during scenario's life cycle (preparation, construction and operation of scenario). The methodology comprises a proposal of following conditions in the view of workers and public exposure: - radionuclide limit concentration of conditionally released materials for specific scenarios and nuclide vectors, - specific deployment of conditionally released materials eventually shielding materials, workers and public during the scenario's life cycle, - organizational measures concerning time of workers or public stay in the vicinity on conditionally released materials for individual performed scenarios and nuclide vectors. The above mentioned steps of proposed methodology have been applied within the CONRELMAT project. Exposure evaluation of workers for rail production is introduced in the article as an example of this application. Exposure calculation using VISIPLAN 3D ALARA planning tool was done within several models. The most exposed profession for scenario was identified. On the basis of this result, an increase of radionuclide concentration in conditional released material was proposed more than two times to 681 Bq/kg without no additional safety or organizational measures being applied. After application of proposed safety and organizational measures (additional shielding, geometry changes and limitation of work duration) it is possible to increase concentration of radionuclide in conditional released material more than ten times to 3092 Bq/kg. Storage

Recycling of hazardous solid waste material using high-temperature solar process heat

Energy Technology Data Exchange (ETDEWEB)

Schaffner, B.; Meier, A.; Wuillemin, D.; Hoffelner, W.; Steinfeld, A.

2003-03-01

A novel high-temperature solar chemical reactor is proposed for the thermal recycling of hazardous solid waste material using concentrated solar power. A 10 kW solar reactor prototype was designed and tested for the carbothermic reduction of electric arc furnace dusts (EAFD). The reactor was subjected to mean solar flux intensities of 2000 kW/m2 and operated in both batch and continuous mode within the temperature range 1120-1400 K. Extraction of up to 99% and 90% of the Zn originally contained in the EAFD was achieved in the residue for the batch and continuous solar experiments, respectively. The condensed off-gas products consisted mainly of Zn, Pb, and Cl. No ZnO was detected when the O{sub 2} concentration remained below 2 vol.-%. The use of concentrated solar energy as the source of process heat offers the possibility of converting hazardous solid waste material into valuable commodities for processes in closed and sustainable material cycles. (author)

Project management plan, Hazardous Materials Management and Emergency Response Training Center

International Nuclear Information System (INIS)

Borgeson, M.E.

1994-01-01

For the next 30 years, the main activities at the Hanford Site will involve the handling and cleanup of toxic substances. Thousands of workers involved in these new activities will need systematic training appropriate to their tasks and associated risks. This project is an important part of the Hanford Site mission and will enable the US Department of Energy (DOE) to meet high standards for safety. The Hazardous Materials Management and Emergency Response Training Center (HAMMER) project will construct a centralized regional training center dedicated to training hazardous materials workers and emergency responders in classrooms and with hands-on, realistic training aids representing actual field conditions. The HAMMER Training Center will provide a cost-effective, high-quality way to meet the Hanford Site training needs. The training center creates a partnership among DOE; government contractors; labor; local, state, and tribal governments; and selected institutions of higher education

Controlled release of phenytoin for epilepsy treatment from titania and silica based materials

International Nuclear Information System (INIS)

Lopez, Tessy; Ortiz, Emma; Meza, Doraliz; Basaldella, Elena; Bokhimi, Xim; Magana, Carlos; Sepulveda, Antonio; Rodriguez, Francisco; Ruiz, Javier

2011-01-01

Research highlights: → Template technique was used to obtain well ordered nanostructured materials: SBA-15 and titania tubes. → Phenytoin (PH), a drug used in epilepsy treatment, was loaded in these materials to used como PH release. → Loaded PH showed a good stability inside the used materials as observed by spectroscopy analysis. → The load-release PH are faster in nanostructured TiO2 tubes than in mesoporous silica matrix. → There is an inverse effect of the surface area of the structured materials on the amount of released PH. - Abstract: Template technique was used to obtain well ordered nanostructured materials: mesoporous silica and nanostructured titania tubes. This technique permits the synthesis of solids with controlled mesoporosity, where a large variety of molecules that have therapeutic activity can be hosted and further released to specific sites. In this work phenytoin (PH), a drug used in epilepsy treatment, was loaded in ordered mesoporous silica (SBA 15) and nanostructured titania tubes (TiO 2 ). The pure materials and those containing PH were characterized by X-ray diffraction, FTIR spectroscopy, transmission electron microscopy (TEM), scanning electron microscopy (SEM) and N 2 adsorption-desorption at 77 K. In order to determine the loading capacity of the antiepileptic drug on these silica- and titania-based materials, the loading and release of PH was investigated using UV-vis spectroscopy. Tubular structures were found for the titania samples, for which the X-ray diffractograms showed to be formed by anatase and rutile phases. On the other hand, an amorphous phase was found in the silica sample. A highly ordered hexagonal structure of 1D cylindrical channels was also observed for this material. Loaded PH showed a good stability inside the used materials as observed by spectroscopy analysis. The adsorption and desorption of PH are faster in nanostructured TiO 2 tubes than in mesoporous silica matrix.

Integrated Life-Cycle Hazardous Material Management: A Logistics Imperative for USAREUR and the 7th Army

National Research Council Canada - National Science Library

Werle, Christopher

2000-01-01

This report examines the benefit to be gained by integrating traditional "pharmacy" business practices in the existing supply system rather than building a parallel system for hazardous material/hazardous waste (HM/HW) management...

Preliminary hazard classification for buildings 1310-N and 1314-N

International Nuclear Information System (INIS)

Kloster, G.L.; Smith, R.I.

1997-01-01

This document establishes the preliminary hazard classification (PHC) for the 100-N Area facility segment comprised of the 1310-N ''silo'' building and the 1314-N Liquid Waste Disposal Building. To establish the PHC, the inventories of radioactive and nonradioactive hazardous materials present within the segment are identified and then compared to the corresponding threshold quantity values in DOE-STD-1027-92 and reportable quantity values in 40 CFR 302.4. In this evaluation, no credit is taken for the form, location, and dispersibility of the materials; for their interaction with available energy sources; or for safety features that could prevent or mitigate a radiological release. The result of the PHC determined that the 1310-N and 1314-N building segments are classified as radiological

Modeling release of chemicals from multilayer materials into food

Directory of Open Access Journals (Sweden)

Huang Xiu-Ling

2016-01-01

Full Text Available The migration of chemicals from materials into food is predictable by various mathematical models. In this article, a general mathematical model is developed to quantify the release of chemicals through multilayer packaging films based on Fick's diffusion. The model is solved numerically to elucidate the effects of different diffusivity values of different layers, distribution of chemical between two adjacent layers and between material and food, mass transfer at the interface of material and food on the migration process.

75 FR 5258 - Hazardous Materials Transportation; Registration and Fee Assessment Program

Science.gov (United States)

2010-02-02

...) train public sector hazardous materials emergency response employees to respond to accidents and... officers, and 500,000 emergency medical services (EMS) providers. Due to the high turnover rates of... planning grants; A new $4,000,000 grant program for non-profit hazmat employee organizations to train...

Release process for non-real property containing residual radioactive material

International Nuclear Information System (INIS)

Ranek, N.L.; Chen, S.Y.; Kamboj, S.; Hensley, J.; Burns, D.; Fleming, R.; Warren, S.; Wallo, A.

1997-01-01

It is DOE's objective to operate its facilities and to conduct its activities so that radiation exposures to members of the public are maintained within acceptable limits and exposures to residual radioactive materials are controlled. To accomplish this, DOE has adopted Order DOE 5400.51 'Radiation Protection of the Public and the Environment', and will be promulgating IO CR Part 834 to codify and clarify the requirements of DOE 5400.5. Under both DOE 5400.5 and 10 CR Part 834, radioactively contaminated DOE property is prohibited from release unless specific actions have been completed prior to the release. This paper outlines a ten-step process that, if followed, will assist DOE Operations and contractor personnel in ensuring that the required actions established by Order DOE 5400.5 and 10 CR Part 834 have been appropriately completed prior to the release for reuse or recycle of non-real property (e.g., office furniture, computers, hand tools, machinery, vehicles and scrap metal). Following the process will assist in ensuring that radiological doses to the public from the released materials will meet applicable regulatory standards and be as low as reasonably achievable (ALARA)

Hazard evaluation of The International Fusion Materials Irradiation Facility

Energy Technology Data Exchange (ETDEWEB)

Burgazzi, Luciano [ENEA-Centro Ricerche ' Ezio Clementel' , Advanced Physics Technology Division, Via Martiri di Monte Sole, 4, 40129 Bologna (Italy)]. E-mail: burgazzi@bologna.enea.it

2005-01-15

The International Fusion Materials Irradiation Facility (IFMIF) is aimed to provide an intense neutron source by a high current deuteron linear accelerator and a high-speed lithium flow target, for testing candidate materials for fusion. Liquid lithium is being circulated through a loop and is kept at a temperature above its freezing point. In the frame of the design phase called Key Element technology Phase (KEP), jointly performed by an international team to verify the most important risk factors, safety assessment of the whole plant has been required in order to identify the hazards associated with the plant operation. This paper discusses the safety assessments that were performed and their outcome: Failure Mode and Effect Analysis (FMEA) approach has been adopted in order to accomplish the task. Main conclusions of the study is that, on account of the safety and preventive measures adopted, potential plant related hazards are confined within the IFMIF security boundaries and great care must be exercised to protect workers and site personnel from operating the plant. The analysis has provided as a result a set of Postulated Initiating Events (PIEs), that is off-normal events, that could result in hazardous consequences for the plant, together with the total frequency and the list of component failures which could induce the PIE: this assures the exhaustive list of major initiating events of accident sequences, helpful to the further accident sequence analysis phase. Finally, for each one of the individuated PIEs, the evaluation of the accident evolution, in terms of effects on the plant and relative countermeasures, has allowed to verify that adequate measures are being taken both to prevent the accident occurrence and to cope with the accident consequences, thus assuring the fulfilment of the safety requirements.

On-site transportation and handling of uranium-233 special nuclear material: Preliminary hazards and accident analysis. Final

International Nuclear Information System (INIS)

Solack, T.; West, D.; Ullman, D.; Coppock, G.; Cox, C.

1995-01-01

U-233 Special Nuclear Material (SNM) currently stored at the T-Building Storage Areas A and B must be transported to the SW/R Tritium Complex for repackaging. This SNM is in the form of oxide powder contained in glass jars which in turn are contained in heat sealed double polyethylene bags. These doubled-bagged glass jars have been primarily stored in structural steel casks and birdcages for approximately 20 years. The three casks, eight birdcages, and one pail/pressure vessel will be loaded onto a transport truck and moved over an eight day period. The Preliminary Hazards and Accident Analysis for the on-site transportation and handling of Uranium-233 Special Nuclear Material, documented herein, was performed in accordance with the format and content guidance of DOE-STD-3009-94, Preparation Guide for US Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports, dated July 1994, specifically Chapter Three, Hazard and Accident Analysis. The Preliminary Hazards Analysis involved detailed walkdowns of all areas of the U-233 SNM movement route, including the T-Building Storage Area A and B, T-Building truck tunnel, and the roadway route. Extensive discussions were held with operations personnel from the Nuclear Material Control Group, Nuclear Materials Accountability Group, EG and G Mound Security and the Material Handling Systems Transportation Group. Existing documentation related to the on-site transportation of hazardous materials, T-Building and SW/R Tritium Complex SARs, and emergency preparedness/response documentation were also reviewed and analyzed to identify and develop the complete spectrum of energy source hazards

Applying radiological emergency planning experience to hazardous materials emergency planning within the nuclear industry

International Nuclear Information System (INIS)

Foltman, A.; Newsom, D.; Lerner, K.

1988-01-01

The nuclear industry has extensive radiological emergency planning (REP) experience that is directly applicable to hazardous materials emergency planning. Recently, the Feed Materials Production Center near Cincinnati, Ohio, successfully demonstrated such application. The REP experience includes conceptual bases and standards for developing plans that have been tested in hundreds of full-scale exercises. The exercise program itself is also well developed. Systematic consideration of the differences between chemical and radiological hazards shows that relatively minor changes to the REP bases and standards are necessary. Conduct of full-scale, REP-type exercises serves to test the plans, provide training, and engender confidence and credibility

Surface Fire Hazards Analysis Technical Report-Constructor Facilities

International Nuclear Information System (INIS)

Flye, R.E.

2000-01-01

The purpose of this Fire Hazards Analysis Technical Report (hereinafter referred to as Technical Report) is to assess the risk from fire within individual fire areas to ascertain whether the U.S. Department of Energy (DOE) fire safety objectives are met. The objectives identified in DOE Order 420.1, Change 2, Facility Safety, Section 4.2, establish requirements for a comprehensive fire and related hazards protection program for facilities sufficient to minimize the potential for: The occurrence of a fire or related event; A fire that causes an unacceptable on-site or off-site release of hazardous or radiological material that will threaten the health and safety of employees, the public, or the environment; Vital DOE programs suffering unacceptable interruptions as a result of fire and related hazards; Property losses from a fire and related events exceeding defined limits established by DOE; and Critical process controls and safety class systems being damaged as a result of a fire and related events

Comparative alternative materials assessment to screen toxicity hazards in the life cycle of CIGS thin film photovoltaics

International Nuclear Information System (INIS)

Eisenberg, Daniel A.; Yu, Mengjing; Lam, Carl W.; Ogunseitan, Oladele A.; Schoenung, Julie M.

2013-01-01

Highlights: • Comparative alternatives assessment of thin film manufacturing technologies. • Development of chemical alternatives assessment in a life cycle context. • Screening of manufacturing and solar cell hazardous substances simultaneously. -- Abstract: Copper–indium–gallium–selenium–sulfide (CIGS) thin film photovoltaics are increasingly penetrating the market supply for consumer solar panels. Although CIGS is attractive for producing less greenhouse gas emissions than fossil-fuel based energy sources, CIGS manufacturing processes and solar cell devices use hazardous materials that should be carefully considered in evaluating and comparing net environmental benefits of energy products. Through this research, we present a case study on the toxicity hazards associated with alternative materials selection for CIGS manufacturing. We applied two numeric models, The Green Screen for Safer Chemicals™ and the Toxic Potential Indicator. To improve the sensitivity of the model outputs, we developed a novel, life cycle thinking based hazard assessment method that facilitates the projection of hazards throughout material life cycles. Our results show that the least hazardous CIGS solar cell device and manufacturing protocol consist of a titanium substrate, molybdenum metal back electrode, CuInS 2 p-type absorber deposited by spray pyrolysis, ZnS buffer deposited by spray ion layer gas reduction, ZnO:Ga transparent conducting oxide (TCO) deposited by sputtering, and the encapsulant polydimethylsiloxane

Final hazard classification and auditable safety analysis for the 308 Building Complex during post-deactivation surveillance and maintenance mode

International Nuclear Information System (INIS)

Dexheimer, D.

1996-11-01

This document summarizes the inventories of radioactive and hazardous materials present within the 308 Building Complex, and presents the hazard evaluation methodology used to prepare the hazard classification for the Complex. The complex includes the 308 Building (process area and office facilities) and the 308 Building Annex, which includes the former Neutron Radiography Facility containing a shutdown (and partially decommissioned) reactor. This document applies to the post-deactivation surveillance and maintenance mode only, and provides an authorization basis limited to surveillance and maintenance activities. This document does not authorize decommissioning and decontamination activities, movement of fissile materials, modification to facility confinement structures, nor the introduction or storage of additional radionuclides in the 308 Building Complex. This document established a final hazard classification and identifies appropriate and adequate safety functions and controls to reduce or mitigate the risk associated with the surveillance and maintenance mode. The most consequential hazard event scenario is a postulated unmitigated release from an earthquake event involving the entire complex. That release is equivalent to 30% of the Nuclear Category 3 threshold adjusted as allowed by DOE-STD-1027-92 (DOE 1992). The dominant isotopes are 239 Pu, 240 Pu, and 241 Am in the gloveboxes

Hazardous materials and toxic substances - Status report

International Nuclear Information System (INIS)

Sommerlad, R.E.

1991-01-01

The paper first forecasts what the status of hazardous wastes should be in the year 2028. The author believes all the problems will be solved: no new hazardous wastes will be being generated and the current hazardous waste problems will have been cleared up by common sense engineering. He then describes the current status of waste management of hazardous wastes, the regulatory situation, as well as combustion test programs

INTERNAL HAZARDS ANALYSIS FOR LICENSE APPLICATION

Energy Technology Data Exchange (ETDEWEB)

R.J. Garrett

2005-02-17

The purpose of this internal hazards analysis is to identify and document the internal hazards and potential initiating events associated with preclosure operations of the repository at Yucca Mountain. Internal hazards are those hazards presented by the operation of the facility and by its associated processes that can potentially lead to a radioactive release or cause a radiological hazard. In contrast to external hazards, internal hazards do not involve natural phenomena and external man-made hazards. This internal hazards analysis was performed in support of the preclosure safety analysis and the License Application for the Yucca Mountain Project. The methodology for this analysis provides a systematic means to identify internal hazards and potential initiating events that may result in a radiological hazard or radiological release during the repository preclosure period. These hazards are documented in tables of potential internal hazards and potential initiating events (Section 6.6) for input to the repository event sequence categorization process. The results of this analysis will undergo further screening and analysis based on the criteria that apply to the performance of event sequence analyses for the repository preclosure period. The evolving design of the repository will be re-evaluated periodically to ensure that internal hazards that have not been previously evaluated are identified.

INTERNAL HAZARDS ANALYSIS FOR LICENSE APPLICATION

International Nuclear Information System (INIS)

Garrett, R.J.

2005-01-01

The purpose of this internal hazards analysis is to identify and document the internal hazards and potential initiating events associated with preclosure operations of the repository at Yucca Mountain. Internal hazards are those hazards presented by the operation of the facility and by its associated processes that can potentially lead to a radioactive release or cause a radiological hazard. In contrast to external hazards, internal hazards do not involve natural phenomena and external man-made hazards. This internal hazards analysis was performed in support of the preclosure safety analysis and the License Application for the Yucca Mountain Project. The methodology for this analysis provides a systematic means to identify internal hazards and potential initiating events that may result in a radiological hazard or radiological release during the repository preclosure period. These hazards are documented in tables of potential internal hazards and potential initiating events (Section 6.6) for input to the repository event sequence categorization process. The results of this analysis will undergo further screening and analysis based on the criteria that apply to the performance of event sequence analyses for the repository preclosure period. The evolving design of the repository will be re-evaluated periodically to ensure that internal hazards that have not been previously evaluated are identified

Hazardous waste shipment data collection from DOE sites

International Nuclear Information System (INIS)

Page, L.A.; Kirkpatrick, T.D.; Stevens, L.

1992-01-01

Past practices at the US Department of Energy (DOE) sites for offsite release of hazardous waste are being reviewed to determine if radioactively contaminated hazardous wastes were released to commercial treatment, storage, and disposal facilities. Records indicating the presence of radioactivity in waste shipped to and treated at a commercial incineration facility led to a ban on offsite hazardous waste shipments and investigation of past practices for offsite release of hazardous waste from the DOE sites. A House of Representatives Interior and Insular Affairs Committee oversight hearing on potentially contaminated waste shipments to commercial facilities concluded that the main issue was the lack of a uniform national standard to govern disposal of mixed waste

Natural radioactivity and associated radiation hazardous of main building materials in Yan'an, China

International Nuclear Information System (INIS)

Li Nan; Lu Xinwei; Yang Guang; Zhao Caifeng

2012-01-01

Background: With the rapidly economic development and urbanization in Yan'an city, more building materials were consumed in building construction. While the natural radioactivity level of building materials from Yan'an is limited in the literatures. Purpose: The main objective of this study is to determine the natural radioactivity level and to analyze the associated radiation hazards of building materials in Yan'an. Methods: The specific activities of natural radionuclides 226 Ra, 232 Th and 40 K in various building materials from Yan'an city were determined using low-background gamma-ray spectrometry, and their radiation hazards were evaluated according to the standard methods. Results: The results show that the specific activities of 226 Ra, 232 Th and 40 K in the building materials are 9.4-73.1, 11.5-86.9 and 258.9-1055.1 Bq/kg, respectively. The activities of 226 Ra and 232 Th, except for sand and gravel aggregate, in all other building materials are higher than the corresponding means of local soil, and the activities of 40 K in hollow brick, red-clay brick, sand and gravel aggregate exceed the means of 40 K in soil. However, the values of internal exposure index, external exposure index and gamma radiation index in all investigated building materials are less than 1. Conclusions: The radiation levels of all analyzed building materials are within the national safety standard, which indicates that all analyzed building materials can be used anywhere and they can't cause radiation hazard to the local residents. (authors)

Survey of naturally occurring hazardous materials in deep geologic formations: a perspective on the relative hazard of deep burial of nuclear wastes

International Nuclear Information System (INIS)

Tonnessen, K.A.; Cohen, J.J.

1977-01-01

Hazards associated with deep burial of solidified nuclear waste are considered with reference to toxic elements in naturally occurring ore deposits. This problem is put into perspective by relating the hazard of a radioactive waste repository to that of naturally occurring geologic formations. The basis for comparison derives from a consideration of safe drinking water levels. Calculations for relative toxicity of FBR waste and light water reactor (LWR) waste in an underground repository are compared with the relative toxicity indices obtained for average concentration ore deposits. Results indicate that, over time, nuclear waste toxicity decreases to levels below those of naturally occurring hazardous materials

Radioactive materials released from nuclear power plants: Annual report, 1984

Energy Technology Data Exchange (ETDEWEB)

Tichler, J.; Norden, K.; Congemi, J.

1987-08-01

Releases of radioactive materials in airborne and liquid effluents from commercial light water reactors during 1984 have been compiled and reported. Data on solid waste shipments as well as selected operating information have been included. This report supplements earlier annual reports issued by the former Atomic Energy Commission and the Nuclear Regulatory Commission. The 1984 release data are summarized in tabular form. Data covering specific radionuclides are summarized.

Comparative alternative materials assessment to screen toxicity hazards in the life cycle of CIGS thin film photovoltaics.

Science.gov (United States)

Eisenberg, Daniel A; Yu, Mengjing; Lam, Carl W; Ogunseitan, Oladele A; Schoenung, Julie M

2013-09-15

Copper-indium-gallium-selenium-sulfide (CIGS) thin film photovoltaics are increasingly penetrating the market supply for consumer solar panels. Although CIGS is attractive for producing less greenhouse gas emissions than fossil-fuel based energy sources, CIGS manufacturing processes and solar cell devices use hazardous materials that should be carefully considered in evaluating and comparing net environmental benefits of energy products. Through this research, we present a case study on the toxicity hazards associated with alternative materials selection for CIGS manufacturing. We applied two numeric models, The Green Screen for Safer Chemicals and the Toxic Potential Indicator. To improve the sensitivity of the model outputs, we developed a novel, life cycle thinking based hazard assessment method that facilitates the projection of hazards throughout material life cycles. Our results show that the least hazardous CIGS solar cell device and manufacturing protocol consist of a titanium substrate, molybdenum metal back electrode, CuInS₂ p-type absorber deposited by spray pyrolysis, ZnS buffer deposited by spray ion layer gas reduction, ZnO:Ga transparent conducting oxide (TCO) deposited by sputtering, and the encapsulant polydimethylsiloxane. Copyright © 2013 Elsevier B.V. All rights reserved.

Controlled release of phenytoin for epilepsy treatment from titania and silica based materials

Energy Technology Data Exchange (ETDEWEB)

Lopez, Tessy, E-mail: tessy3@prodigy.net.mx [Universidad Autonoma Metropolitana-Xochimilco. Departamento de Microbiologia. Calzada del Hueso 1100, Col. Villa Quietud, Coyoacan, C.P. 04960, Mexico D.F. Mexico (Mexico); Instituto Nacional de Neurologia y Neurocirugia ' MVS' . Laboratorio de Nanotecnologia. Av. Insurgentes Sur 3877, Col. La Fama, Tlalpan, 14269, Mexico, D.F. Mexico (Mexico); Department of Chemical and Biomolecular Engineering, Tulane University, New Orleans, LA 70118 (United States); Ortiz, Emma [Instituto Nacional de Neurologia y Neurocirugia ' MVS' . Laboratorio de Nanotecnologia. Av. Insurgentes Sur 3877, Col. La Fama, Tlalpan, 14269, Mexico, D.F. Mexico (Mexico); Meza, Doraliz [Universidad Autonoma Metropolitana-Iztapalapa, Departamento de Quimica, Av. San Rafael Atlixco 186, A.P. 55-534, Mexico D.F., C.P. 09340 (Mexico); Basaldella, Elena [CIC-CINDECA - Universidad Nacional de La Plata - Calle 47 No 257 - La Plata (Argentina); Bokhimi, Xim; Magana, Carlos [Instituto de fisica, UNAM. Circuito de la Investigacion s/n. C.U. Mexico D.F. 01000 (Mexico); Sepulveda, Antonio; Rodriguez, Francisco; Ruiz, Javier [Departamento de Quimica Inorganica, Universidad de Alicante. Apartado 99, E-03080 Alicante, Espana Spain (Spain)

2011-04-15

Research highlights: {yields} Template technique was used to obtain well ordered nanostructured materials: SBA-15 and titania tubes. {yields} Phenytoin (PH), a drug used in epilepsy treatment, was loaded in these materials to used como PH release. {yields} Loaded PH showed a good stability inside the used materials as observed by spectroscopy analysis. {yields} The load-release PH are faster in nanostructured TiO2 tubes than in mesoporous silica matrix. {yields} There is an inverse effect of the surface area of the structured materials on the amount of released PH. - Abstract: Template technique was used to obtain well ordered nanostructured materials: mesoporous silica and nanostructured titania tubes. This technique permits the synthesis of solids with controlled mesoporosity, where a large variety of molecules that have therapeutic activity can be hosted and further released to specific sites. In this work phenytoin (PH), a drug used in epilepsy treatment, was loaded in ordered mesoporous silica (SBA 15) and nanostructured titania tubes (TiO{sub 2}). The pure materials and those containing PH were characterized by X-ray diffraction, FTIR spectroscopy, transmission electron microscopy (TEM), scanning electron microscopy (SEM) and N{sub 2} adsorption-desorption at 77 K. In order to determine the loading capacity of the antiepileptic drug on these silica- and titania-based materials, the loading and release of PH was investigated using UV-vis spectroscopy. Tubular structures were found for the titania samples, for which the X-ray diffractograms showed to be formed by anatase and rutile phases. On the other hand, an amorphous phase was found in the silica sample. A highly ordered hexagonal structure of 1D cylindrical channels was also observed for this material. Loaded PH showed a good stability inside the used materials as observed by spectroscopy analysis. The adsorption and desorption of PH are faster in nanostructured TiO{sub 2} tubes than in mesoporous silica

Hazardous Materials Pharmacies - A Vital Component of a Robust P2 Program

International Nuclear Information System (INIS)

McCarter, S.

2006-01-01

Integrating pollution prevention (P2) into the Department of Energy Integrated Safety Management (ISM) - Environmental Management System (EMS) approach, required by DOE Order 450.1, leads to an enhanced ISM program at large and complex installations and facilities. One of the building blocks to integrating P2 into a comprehensive environmental and safety program is the control and tracking of the amounts, types, and flow of hazardous materials used on a facility. Hazardous materials pharmacies (typically called HazMarts) provide a solid approach to resolving this issue through business practice changes that reduce use, avoid excess, and redistribute surplus. If understood from concept to implementation, the HazMart is a powerful tool for reducing pollution at the source, tracking inventory storage, controlling usage and flow, and summarizing data for reporting requirements. Pharmacy options can range from a strict, single control point for all hazardous materials to a virtual system, where the inventory is user controlled and reported over a common system. Designing and implementing HazMarts on large, diverse installations or facilities present a unique set of issues. This is especially true of research and development (R and D) facilities where the chemical use requirements are extensive and often classified. There are often multiple sources of supply; a wide variety of chemical requirements; a mix of containers ranging from small ampoules to large bulk storage tanks; and a wide range of tools used to track hazardous materials, ranging from simple purchase inventories to sophisticated tracking software. Computer systems are often not uniform in capacity, capability, or operating systems, making it difficult to use a server-based unified tracking system software. Each of these issues has a solution or set of solutions tied to fundamental business practices. Each requires an understanding of the problem at hand, which, in turn, requires good communication among all

Influence of plume rise on the consequences of radioactive material releases

International Nuclear Information System (INIS)

Russo, A.J.; Wayland, J.R.; Ritchie, L.T.

1977-01-01

Estimates of health consequences resulting from a postulated nuclear reactor accident can be strongly dependent on the buoyant rise of the plume of released radioactive material. The sensitivity of the consequences of a postulated accident to two different plume rise models has been investigated. The results of these investigations are the subject of this report. One of the models includes the effects of emission angle, momentum, and radioactive heating of the released material. The difference in the consequence estimates from the two models can exceed an order of magnitude under some conditions, but in general the results are similar

The Hazardous Material Technician Apprenticeship Program at Lawrence Livermore National Laboratory

International Nuclear Information System (INIS)

Steiner, S.D.

1987-07-01

This document describes an apprenticeship training program for hazardous material technician. This entry-level category is achieved after approximately 216 hours of classroom and on-the-job training. Procedures for evaluating performance include in-class testing, use of on-the-job checks, and the assignment of an apprentice mentor for each trainee

Reduction of Fire Hazard in Materials for Irrigators and Water Collectors in Cooling Towers

Energy Technology Data Exchange (ETDEWEB)

Smirnov, N. V.; Konstantinova, N. I., E-mail: konstantinova-n@inbox.ru [FGBU VNIIPO of EMERCOM of Russia (All-Russian Scientific-research Institute of Fire Protection) (Russian Federation); Gordon, E. P. [Research and Production Center “Kaustik” (Russian Federation); Poedintsev, E. A. [FGBU VNIIPO of EMERCOM of Russia (All-Russian Scientific-research Institute of Fire Protection) (Russian Federation)

2016-09-15

A way of reducing the fire hazard of PVC film used to make cooling-tower irrigators and water collectors is examined. A new generation of fire retardant, nanostructured magnesium hydroxide, is used to impart fire retardant properties. The fabrication technology is optimized with a roller-calendering manufacturing technique, and the permissible ranges of fire hazard indicators for materials in irrigators and water collectors are determined.

In vitro release of doxycycline from bioabsorbable materials and acrylic strips

DEFF Research Database (Denmark)

Larsen, T

1990-01-01

Treatment of marginal periodontitis may include use of local antibiotics. In the present in vitro study the bioabsorbable materials Surgicel, Tissell, and CollaCote and acrylic strips were examined for release of doxycycline into liquids and residual antibacterial activity of the materials. Pieces...

Comparative alternative materials assessment to screen toxicity hazards in the life cycle of CIGS thin film photovoltaics

Energy Technology Data Exchange (ETDEWEB)

Eisenberg, Daniel A.; Yu, Mengjing; Lam, Carl W. [University of California, Davis, 1 Shields Avenue, Davis, CA 95616 (United States); Ogunseitan, Oladele A. [University of California, Irvine, Irvine, CA 92697 (United States); Schoenung, Julie M., E-mail: jmschoenung@ucdavis.edu [University of California, Davis, 1 Shields Avenue, Davis, CA 95616 (United States)

2013-09-15

Highlights: • Comparative alternatives assessment of thin film manufacturing technologies. • Development of chemical alternatives assessment in a life cycle context. • Screening of manufacturing and solar cell hazardous substances simultaneously. -- Abstract: Copper–indium–gallium–selenium–sulfide (CIGS) thin film photovoltaics are increasingly penetrating the market supply for consumer solar panels. Although CIGS is attractive for producing less greenhouse gas emissions than fossil-fuel based energy sources, CIGS manufacturing processes and solar cell devices use hazardous materials that should be carefully considered in evaluating and comparing net environmental benefits of energy products. Through this research, we present a case study on the toxicity hazards associated with alternative materials selection for CIGS manufacturing. We applied two numeric models, The Green Screen for Safer Chemicals™ and the Toxic Potential Indicator. To improve the sensitivity of the model outputs, we developed a novel, life cycle thinking based hazard assessment method that facilitates the projection of hazards throughout material life cycles. Our results show that the least hazardous CIGS solar cell device and manufacturing protocol consist of a titanium substrate, molybdenum metal back electrode, CuInS{sub 2} p-type absorber deposited by spray pyrolysis, ZnS buffer deposited by spray ion layer gas reduction, ZnO:Ga transparent conducting oxide (TCO) deposited by sputtering, and the encapsulant polydimethylsiloxane.

The effect of release liner materials on adhesive contaminants, paper recycling and recycled paper properties

Science.gov (United States)

Richard Venditti; Richard Gilbert; Andy Zhang; Said Abubakr

2000-01-01

Release liner waste material is found in post-consumer waste streams and is also a significant component of the preconsumer waste stream generated in the manufacturing of adhesive products. To date, very little has been reported pertaining to the behavior of release liner in paper recycling. In this study, the effect of the release liner material on the behavior of...

Bulk-scaffolded hydrogen storage and releasing materials and methods for preparing and using same

Science.gov (United States)

Autrey, S Thomas [West Richland, WA; Karkamkar, Abhijeet J [Richland, WA; Gutowska, Anna [Richland, WA; Li, Liyu [Richland, WA; Li, Xiaohong S [Richland, WA; Shin, Yongsoon [Richland, WA

2011-06-21

Compositions are disclosed for storing and releasing hydrogen and methods for preparing and using same. These hydrogen storage and releasing materials exhibit fast release rates at low release temperatures without unwanted side reactions, thus preserving desired levels of purity and enabling applications in combustion and fuel cell applications.

An examination of the Hazardous Materials Transportation Uniform Safety Act (HMTUSA): A southern perspective

International Nuclear Information System (INIS)

1992-03-01

On November 16,1990, President Bush signed into law the most comprehensive amendments to the Hazardous Materials Transportation Act (HMTA) in 15 years. The Hazardous Materials Transportation Uniform Safety Act of 1990 (HMTUSA) was created by Congress in an effort to strengthen and clarify the HMTA. This paper will discuss the act's provisions as they affect shipments of spent fuel and high-level radioactive materials as well as the impact of those provisions on routing and emergency response issues in the southern region. HMTUSA consists of seven key provisions that affect radioactive materials: clarification of regulatory jurisdiction; highway routing standards; broadened industry registration; safety permits for motor carriers of high risk materials; expanded nuclear transportation requirements; new provisions for emergency response training and planning; and a public process for assessing the feasibility of a federally operated central reporting system and data center. In addition to amending various HMTA provisions, the new HMTUSA act provides appropriations to carry out the specific goals of the legislation. The act authorizes appropriations for the 1991, 1992 and 1993 fiscal years

Hazardous Waste/Mixed Waste Treatment Building Safety Information Document (SID)

International Nuclear Information System (INIS)

Fatell, L.B.; Woolsey, G.B.

1993-01-01

This Safety Information Document (SID) provides a description and analysis of operations for the Hazardous Waste/Mixed Waste Disposal Facility Treatment Building (the Treatment Building). The Treatment Building has been classified as a moderate hazard facility, and the level of analysis performed and the methodology used are based on that classification. Preliminary design of the Treatment Building has identified the need for two separate buildings for waste treatment processes. The term Treatment Building applies to all these facilities. The evaluation of safety for the Treatment Building is accomplished in part by the identification of hazards associated with the facility and the analysis of the facility's response to postulated events involving those hazards. The events are analyzed in terms of the facility features that minimize the causes of such events, the quantitative determination of the consequences, and the ability of the facility to cope with each event should it occur. The SID presents the methodology, assumptions, and results of the systematic evaluation of hazards associated with operation of the Treatment Building. The SID also addresses the spectrum of postulated credible events, involving those hazards, that could occur. Facility features important to safety are identified and discussed in the SID. The SID identifies hazards and reports the analysis of the spectrum of credible postulated events that can result in the following consequences: Personnel exposure to radiation; Radioactive material release to the environment; Personnel exposure to hazardous chemicals; Hazardous chemical release to the environment; Events leading to an onsite/offsite fatality; and Significant damage to government property. The SID addresses the consequences to the onsite and offsite populations resulting from postulated credible events and the safety features in place to control and mitigate the consequences

Hazardous Waste/Mixed Waste Treatment Building Safety Information Document (SID)

Energy Technology Data Exchange (ETDEWEB)

Fatell, L.B.; Woolsey, G.B.

1993-04-15

This Safety Information Document (SID) provides a description and analysis of operations for the Hazardous Waste/Mixed Waste Disposal Facility Treatment Building (the Treatment Building). The Treatment Building has been classified as a moderate hazard facility, and the level of analysis performed and the methodology used are based on that classification. Preliminary design of the Treatment Building has identified the need for two separate buildings for waste treatment processes. The term Treatment Building applies to all these facilities. The evaluation of safety for the Treatment Building is accomplished in part by the identification of hazards associated with the facility and the analysis of the facility`s response to postulated events involving those hazards. The events are analyzed in terms of the facility features that minimize the causes of such events, the quantitative determination of the consequences, and the ability of the facility to cope with each event should it occur. The SID presents the methodology, assumptions, and results of the systematic evaluation of hazards associated with operation of the Treatment Building. The SID also addresses the spectrum of postulated credible events, involving those hazards, that could occur. Facility features important to safety are identified and discussed in the SID. The SID identifies hazards and reports the analysis of the spectrum of credible postulated events that can result in the following consequences: Personnel exposure to radiation; Radioactive material release to the environment; Personnel exposure to hazardous chemicals; Hazardous chemical release to the environment; Events leading to an onsite/offsite fatality; and Significant damage to government property. The SID addresses the consequences to the onsite and offsite populations resulting from postulated credible events and the safety features in place to control and mitigate the consequences.

STRRAP system-A software for hazardous materials risk assessment and safe distances calculation

International Nuclear Information System (INIS)

Godoy, S.M.; Santa Cruz, A.S.M.; Scenna, N.J.

2007-01-01

This work presents a powerful computational tool (Stochastic Toxic Release Risk Assessment Package, STRRAP) useful in risk assessment and emergency planning (safe distance calculation), which allows to handle the stochastic uncertainty of atmospheric parameters, critical for risk calculation when diffusion of hazardous gases or particulate matter occur as a consequence of an emission or accidental release. In fact, the random behaviour of wind intensity, wind direction, atmospheric stability and temperature, given a time horizon, (a season or a complete year), is taken into account considering also the day or night condition. STRRAP can be used for releases or emissions from static sources (for example a stack or a fixed tank in a facility) or from transportation accidents (road, rail, maritime and pipeline transport) involving different scenarios. After a stochastic simulation based on well-known diffusion models (dense and light gases, particulate matter) is carried out, the downwind pollutant concentrations are obtained, in order to compute safe distances and/or individual and societal risks. Some study cases are analyzed to show STRRAP capabilities

78 FR 22798 - Hazardous Materials: Revision of Maximum and Minimum Civil Penalties

Science.gov (United States)

2013-04-17

.... 5101 et seq.). Section 5123(a) of that law provides civil penalties for knowing violations of Federal... 107--Guidelines for Civil Penalties * * * * * IV. * * * C. * * * Under the Federal hazmat law, 49 U.S... Maximum and Minimum Civil Penalties AGENCY: Pipeline and Hazardous Materials Safety Administration (PHMSA...

Atmospheric Release Advisory Capability (ARAC)

International Nuclear Information System (INIS)

Dickerson, M.H.

1975-01-01

The chief purpose of ARAC data acquisition program is to provide site officials, who are responsible for ensuring maximum health protection for the endangered site personnel and public, with estimates of the effects of atmospheric releases of hazardous material as rapidly and accurately as possible. ARAC is in the initial stages of being implemented and is therefore susceptible to changes before it reaches its final form. However the concept of ARAC is fully developed and was successfully demonstrated during a feasibility study conducted in June 1974, as a joint effort between the Savannah River Laboratory (SRL) and Lawrence Livermore Laboratory (LLL). Additional tests between SRL and LLL are scheduled for December 1975. While the immediate goal is the application of ARAC to assist a limited number of ERDA sites, the system is designed with sufficient flexibility to permit expanding the service to a large number of sites. Success in ARAC application should provide nuclear facilities with a means to handle better the urgent questions concerning the potential accidental hazards from atmospheric releases in addition to providing the sites with a capability to assess the effort of their normal operations

Material Selection for Cable Gland to Improved Reliability of the High-hazard Industries

Science.gov (United States)

Vashchuk, S. P.; Slobodyan, S. M.; Deeva, V. S.; Vashchuk, D. S.

2018-01-01

The sealed cable glands (SCG) are available to ensure safest connection sheathed single wire for the hazard production facility (nuclear power plant and others) the same as pilot cable, control cables, radio-frequency cables et al. In this paper, we investigate the specifics of the material selection of SCG with the express aim of hazardous man-made facility. We discuss the safe working conditions for cable glands. The research indicates the sintering powdered metals cables provide the reliability growth due to their properties. A number of studies have demonstrated the verification of material selection. On the face of it, we make findings indicating that double glazed sealed units could enhance reliability. We had evaluated sample reliability under fire conditions, seismic load, and pressure containment failure. We used the samples mineral insulated thermocouple cable.

Release of axonally transported material from an in vitro amphibian sciatic nerve preparation

International Nuclear Information System (INIS)

Snyder, R.E.

1988-01-01

The rapid axonal transport of a pulse of [35S]methionine-labelled material was used to study the release of transported material from amphibian nerve maintained in vitro. Following creation of a moving pulse of activity in a dorsal root ganglion-sciatic nerve preparation, the ganglion was removed and the nerve placed in a three-compartment tray, the section of nerve in the middle compartment containing no truncated branches (unbranched section). All three compartments were filled with a saline solution that in some studies contained nonradioactive methionine (1.0 mmol/L). Analysis of studies in which nonradioactive methionine was absent revealed that labelled material appeared in the bathing solution of the end compartments that contained truncated branches, but not in the solution of the middle (unbranched) compartment. The quantity of label released in the branched compartments was approximately 6% of that remaining in the corresponding section of nerve following an 18-20 h incubation period. However, when nonradioactive methionine was present, all compartments showed an additional activity in the bathing solution of approximately 10% of that remaining in the nerve. In another study in which a position-sensitive detector of ionizing radiation was used to monitor progress of the pulse, it was found that activity did not enter the bathing solution of a compartment prior to the pulse of activity. It is concluded that in the absence of methionine from the bathing solution, axonally transported material is released only from regions of nerve that contain severed axons; however, the presence of methionine allows transported material to be released from nerve containing intact axons. Ultrafiltration studies and thin-layer chromatography revealed the majority of material released to be of low-molecular weight (less than 30,000 daltons) and not free [35S]methionine

A Selection of Nitric Oxide-Releasing Materials Incorporating S-Nitrosothiols

Science.gov (United States)

Lutzke, Alec

Nitric oxide (NO) is a diatomic radical that occurs as a crucial component of mammalian biochemistry. As a signaling molecule, NO participates in the regulation of vascular tone and maintains the natural antithrombotic function of the healthy endothelium. Furthermore, NO is produced by phagocytes as part of the immune response, and exhibits both antimicrobial and wound-healing effects. In combination, these beneficial properties have led to the use of exogenous NO as a multifunctional therapeutic agent. However, the comparatively short half-life of NO under physiological conditions often renders systemic administration infeasible. This limitation is addressed by the use of NO-releasing polymeric materials, which permit the localized delivery of NO directly at the intended site of action. Such polymers have been utilized in the development of antithrombotic or antibacterial materials for biointerfacial applications, including tissue engineering and the fabrication of medical devices. NO release from polymers has most frequently been achieved through the incorporation of functional groups that are susceptible to NO-forming chemical decomposition in response to appropriate environmental stimuli. While numerous synthetic sources of NO are known, the S-nitrosothiol (RSNO) functional group occurs naturally in the form of S-nitrosocysteine residues in both proteins and small molecule species such as S-nitrosoglutathione. RSNOs are synthesized directly from thiol precursors, and their NO-forming decay has generally been established to produce the corresponding disulfide as a relatively benign organic byproduct. For these reasons, RSNOs have been conscripted as practical NO donors within a physiological environment. This dissertation describes the synthesis and characterization of RSNO-based NO-releasing polymers derived from the polysaccharides chitin and chitosan, as well as the development of amino acid ester-based NO-releasing biodegradable poly

Decision Support for Environmental Management of Industrial Non-Hazardous Secondary Materials: New Analytical Methods Combined with Simulation and Optimization Modeling

Science.gov (United States)

Non-hazardous solid materials from industrial processes, once regarded as waste and disposed in landfills, offer numerous environmental and economic advantages when put to beneficial uses (BUs). Proper management of these industrial non-hazardous secondary materials (INSM) requir...

Ice-Release and Erosion Resistant Materials for Wind Turbines

Science.gov (United States)

Zhang, Wei; Brinn, Cameron; Cook, Alex; Pascual-Marquez, Fernando

2017-11-01

Icing conditions may cause wind turbine generators to partially lose productivity or to be completely shut down to avoid structural damage. At present, commercially available technologies to mitigate this problem consist of expensive, energy hungry heating elements, which costs roughly 70,000 euro per medium size turbine. Conventional passive ice protection coating systems heavily rely on delicate surface structures and expensive materials to create water repellent superhydrophobic / low surface energy surfaces, which have been proven to be ineffective against ice accumulation. The lack of performance among conventional ice protection materials stems from a flaw in the approach to the problem: failure to recognize that water in its liquid form (WATER) and water in its solid form (ICE) are two different things. Something that works for WATER does not automatically work for ICE. Another reason is that many superhydrophobic materials are often reliant upon often fragile micro-structured surfaces to achieve their intended effects. This paper discusses a fundamentally different approach to the creation of a robust, low cost, durable, and multifunctional materials for ice release and erosion resistance. This National Science Foundation sponsored ice-release coating technology holds promise for protecting wind turbine blades and towers, thus potentially increasing reliability for power generation under icing conditions. Because of the vulnerability of wind turbine blades to ice buildup and erosion damages, wind farm facilities stand to reap considerable benefits.

Building 894 hazards assessment document

International Nuclear Information System (INIS)

Banda, Z.; Williams, M.

1996-07-01

The Department of Energy Order 5500.3A requires facility-specific hazards assessments be prepared, maintained, and used for emergency planning purposes. This hazards assessment document describes the chemical and radiological hazards associated with Building 894. The entire inventory was subjected to the screening criteria for potential airborne impact to onsite and offsite individuals out of which 9 chemicals were kept for further evaluation. The air dispersion model, ALOHA, estimated pollutant concentrations downwind from the source of a release, taking into consideration the toxicological and physical characteristics of the release site, the atmospheric conditions, and the circumstances of the release. The greatest distance at which a postulated facility event will produce consequences exceeding the Early Severe Health Effects threshold is 130 meters. The highest emergency classification is a General Emergency. The Emergency Planning Zone is a nominal 130 meter area that conforms to DOE boundaries and physical/jurisdictional boundaries such as fence lines and streets

Building 6630 hazards assessment document

International Nuclear Information System (INIS)

Williams, M.; Banda, Z.

1996-10-01

The Department of Energy Order 5500.3A requires facility-specific hazards assessments be prepared, maintained, and used for emergency planning purposes. This hazards assessment document describes the chemical and radiological hazards associated with Building 6630. The entire inventory was subjected to the screening criteria for potential airborne impact to onsite and offsite individuals out of which one chemical was kept for further evaluation. The air dispersion model, ALOHA, estimated pollutant concentrations downwind from the source of a release, taking into consideration the toxicological and physical characteristics of the chemical release site, the atmospheric conditions, and the circumstances of the release. The greatest distance at which a postulated facility event will produce consequences exceeding the Early Severe Health Effects threshold is 76 meters. The highest emergency classification is an Alert. The Emergency Planning Zone is a nominal 100 meter area that conforms to DOE boundaries and physical/jurisdictional boundaries such as fence lines and streets

Conceptual design report, Hazardous Materials Management and Emergency Response (HAMMER) Training Center

Energy Technology Data Exchange (ETDEWEB)

Kelly, K.E. [Westinghouse Hanford Co., Richland, WA (United States)

1994-11-09

For the next 30 years, the main activities at the US Department of Energy (DOE) Hanford Site will involve the management, handling, and cleanup of toxic substances. If the DOE is to meet its high standards of safety, the thousands of workers involved in these activities will need systematic training appropriate to their tasks and the risks associated with these tasks. Furthermore, emergency response for DOE shipments is the primary responsibility of state, tribal, and local governments. A collaborative training initiative with the DOE will strengthen emergency response at the Hanford Site and within the regional communities. Local and international labor has joined the Hazardous Materials Management and Emergency Response (HAMMER) partnership, and will share in the HAMMER Training Center core programs and facilities using their own specialized trainers and training programs. The HAMMER Training Center will provide a centralized regional site dedicated to the training of hazardous material, emergency response, and fire fighting personnel.

Conceptual design report, Hazardous Materials Management and Emergency Response (HAMMER) Training Center

International Nuclear Information System (INIS)

Kelly, K.E.

1994-01-01

For the next 30 years, the main activities at the US Department of Energy (DOE) Hanford Site will involve the management, handling, and cleanup of toxic substances. If the DOE is to meet its high standards of safety, the thousands of workers involved in these activities will need systematic training appropriate to their tasks and the risks associated with these tasks. Furthermore, emergency response for DOE shipments is the primary responsibility of state, tribal, and local governments. A collaborative training initiative with the DOE will strengthen emergency response at the Hanford Site and within the regional communities. Local and international labor has joined the Hazardous Materials Management and Emergency Response (HAMMER) partnership, and will share in the HAMMER Training Center core programs and facilities using their own specialized trainers and training programs. The HAMMER Training Center will provide a centralized regional site dedicated to the training of hazardous material, emergency response, and fire fighting personnel

Notification: Audit of Security Categorization for EPA Systems That Handle Hazardous Material Information

Science.gov (United States)

Project #OA-FY18-0089, January 8, 2018. The OIG plans to begin preliminary research to determine whether the EPA classified the sensitivity of data for systems that handle hazardous waste material information as prescribed by NIST.

Double-pulse standoff laser-induced breakdown spectroscopy for versatile hazardous materials detection

Energy Technology Data Exchange (ETDEWEB)

Gottfried, Jennifer L. [U.S. Army Research Laboratory, AMSRD-ARL-WM-BD, Aberdeen Proving Ground, MD, 21005-5069 (United States)], E-mail: jennifer.gottfried@arl.army.mil; De Lucia, Frank C.; Munson, Chase A.; Miziolek, Andrzej W. [U.S. Army Research Laboratory, AMSRD-ARL-WM-BD, Aberdeen Proving Ground, MD, 21005-5069 (United States)

2007-12-15

We have developed a double-pulse standoff laser-induced breakdown spectroscopy (ST-LIBS) system capable of detecting a variety of hazardous materials at tens of meters. The use of a double-pulse laser improves the sensitivity and selectivity of ST-LIBS, especially for the detection of energetic materials. In addition to various metallic and plastic materials, the system has been used to detect bulk explosives RDX and Composition-B, explosive residues, biological species such as the anthrax surrogate Bacillus subtilis, and chemical warfare simulants at 20 m. We have also demonstrated the discrimination of explosive residues from various interferents on an aluminum substrate.

Expert geographical information system for assessing hazardous materials in aquatic environments

International Nuclear Information System (INIS)

Regens, J.L.; White, L.; Wright, J.D.; Rene, A.; Mielke, H.; Bakeer, R.; Belkhouche, B.; Barber, M.

1993-01-01

Hazardous substances, including radionuclides, heavy metals, chlorinated hydrocarbons, and industrial solvents, pose unique challenges in terms of environmental restoration and waste management, especially in aquatic environments. When stored, used or disposed of improperly, hazardous materials including transuranic wastes, high level wastes, low level wastes, greater than class C wastes, mixed wastes or chemical wastes can contaminate an array of environmental receptors ranging from soils, sediments, groundwater to surface water. Depending on the specific hazardous substance and site attributes, environmental restoration and waste management can be a complex, problematic activity. This is particularly true for the major Defense Programs facilities managed by the Department of Energy (DOE). This research cluster consists of two discrete elements. Project Element No. 1 develops and applies GIS-based approaches to decision support for environmental restoration by delineating potential exposures and health risks at the Rocky Flats Plant and profiling contemporary and historical demographic/land use patterns at Sandia National Laboratories. Project Element No. 2 develops ESS software for surface water and ground water contaminants in the Mississippi River Basin

Applicability of Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA) to releases of radioactive substances

International Nuclear Information System (INIS)

Miller, S.R.

1987-01-01

The Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA), commonly called Superfund, provided a $1.6 billion fund (financed by a tax on petrochemical feedstocks and crude oil and by general revenues) for the cleanup of releases of hazardous substances, including source, special nuclear or byproduct material, and other radioactive substances, from mostly inactive facilities. The US Environmental Protection Agency (EPA) is authorized to require private responsible parties to clean up releases of hazardous substances, or EPA, at its option, may undertake the cleanup with monies from the Fund and recover the monies through civil actions brought against responsible parties. CERCLA imposes criminal penalties for noncompliance with its reporting requirements. This paper will overview the key provisions of CERCLA which apply to the cleanup of radioactive materials

Understanding and managing the movements of hazardous material shipments through Texas population centers.

Science.gov (United States)

2009-08-01

Every day almost a million shipments of hazardous materials move safely and securely along our nations transportation system, via any combination of modes. Only a small fraction of total shipments interrupt their planned journey due to an incident...

Monitoring for radioactive materials releasing to environment in M310 reformatived nuclear power plant

International Nuclear Information System (INIS)

Yin Zhenyu; Yang Guangli; Xu Guang

2012-01-01

Airborne radioactive materials of nuclear power plant (NPP) releases to the environment from the stack of NPP. Radioactive liquid waste releases of the ocean, the fluvial and the lake through the liquid waste letdyke of NPP. Further more, a few radioactive waste may be taken out of the NPP by vehicle or personnel. For the purpose of strict management and control above-mentioned waste, we use detect equipment monitoring radioactive waste of NPP. Management and control for the releasing of radioactive material to the environment in M310 reformatived NPP is strict and safety. (authors)

Application of United States Department of Transportation regulations to hazardous material and waste shipments on the Hanford site

International Nuclear Information System (INIS)

Burnside, M.E.

1992-01-01

All hazardous material and waste transported over roadways open to the public must be in compliance with the U.S. Department of Transportation (DOT) regulations. The DOT states that the hazardous material regulations (HMR) also apply to government-owned, contractor-operated (GOCO) transportation operations over any U.S. Department of Energy (DOE) site roadway where the public has free and unrestricted access. Hazardous material and waste in packages that do not meet DOT regulations must be transported on DOE site roadways in a manner that excludes the public and nonessential workers. At the DOE Richland Field Office (the Hanford Site), hazardous material and waste movements that do not meet DOT requirements are transported over public access roadways during off-peak hours with the roadways barricaded. These movements are accomplished using a transportation plan that involves the DOE, DOE contractors, and private utilities who operate on or near the Hanford Site. This method, which is used at the Hanford Site to comply with DOT regulations onsite, can be communicated to other DOE sites to provide a basis for achieving consistency in similar transportation operations. (author)

Modelling short term individual exposure from airborne hazardous releases in urban environments

International Nuclear Information System (INIS)

Bartzis, J.G.; Efthimiou, G.C.; Andronopoulos, S.

2015-01-01

Highlights: • The statistical behavior of the variability of individual exposure is described with a beta function. • The extreme value in the beta function is properly addressed by [5] correlation. • Two different datasets gave clear support to the proposed novel theory and its hypotheses. - Abstract: A key issue, in order to be able to cope with deliberate or accidental atmospheric releases of hazardous substances, is the ability to reliably predict the individual exposure downstream the source. In many situations, the release time and/or the health relevant exposure time is short compared to mean concentration time scales. In such a case, a significant scatter of exposure levels is expected due to the stochastic nature of turbulence. The problem becomes even more complex when dispersion occurs over urban environments. The present work is the first attempt to approximate on generic terms, the statistical behavior of the abovementioned variability with a beta distribution probability density function (beta-pdf) which has proved to be quite successful. The important issue of the extreme concentration value in beta-pdf seems to be properly addressed by the [5] correlation in which global values of its associated constants are proposed. Two substantially different datasets, the wind tunnel Michelstadt experiment and the field Mock Urban Setting Trial (MUST) experiment gave clear support to the proposed novel theory and its hypotheses. In addition, the present work can be considered as basis for further investigation and model refinements.

Modelling short term individual exposure from airborne hazardous releases in urban environments

Energy Technology Data Exchange (ETDEWEB)

Bartzis, J.G., E-mail: bartzis@uowm.gr [University of Western Macedonia, Dept. of Mechanical Engineering, Sialvera & Bakola Str., 50100, Kozani (Greece); Efthimiou, G.C.; Andronopoulos, S. [Environmental Research Laboratory, INRASTES, NCSR Demokritos, Patriarchou Grigoriou & Neapoleos Str., 15310, Aghia Paraskevi (Greece)

2015-12-30

Highlights: • The statistical behavior of the variability of individual exposure is described with a beta function. • The extreme value in the beta function is properly addressed by [5] correlation. • Two different datasets gave clear support to the proposed novel theory and its hypotheses. - Abstract: A key issue, in order to be able to cope with deliberate or accidental atmospheric releases of hazardous substances, is the ability to reliably predict the individual exposure downstream the source. In many situations, the release time and/or the health relevant exposure time is short compared to mean concentration time scales. In such a case, a significant scatter of exposure levels is expected due to the stochastic nature of turbulence. The problem becomes even more complex when dispersion occurs over urban environments. The present work is the first attempt to approximate on generic terms, the statistical behavior of the abovementioned variability with a beta distribution probability density function (beta-pdf) which has proved to be quite successful. The important issue of the extreme concentration value in beta-pdf seems to be properly addressed by the [5] correlation in which global values of its associated constants are proposed. Two substantially different datasets, the wind tunnel Michelstadt experiment and the field Mock Urban Setting Trial (MUST) experiment gave clear support to the proposed novel theory and its hypotheses. In addition, the present work can be considered as basis for further investigation and model refinements.

Radiological hazards of alpha-contaminated waste

International Nuclear Information System (INIS)

Rodgers, J.C.

1982-01-01

The radiological hazards of alpha-contaminated wastes are discussed in this overview in terms of two components of hazard: radiobiological hazard, and radioecological hazard. Radiobiological hazard refers to human uptake of alpha-emitters by inhalation and ingestion, and the resultant dose to critical organs of the body. Radioecological hazard refers to the processes of release from buried wastes, transport in the environment, and translocation to man through the food chain. Besides detailing the sources and magnitude of hazards, this brief review identifies the uncertainties in their estimation, and implications for the regulatory process

In-pile test of tritium release from tritium breeding materials (VOM-21H experiment)

International Nuclear Information System (INIS)

Kurasawa, Toshimasa; Takeshita, Hidefumi; Watanabe, Hitoshi; Yoshida, Hiroshi.

1986-10-01

Material development and blanket design of lithium-based ceramics such as lithium oxide, lithium aluminate, lithium silicate and lithium zirconate have been performed in Japan, United State of America and Europian Communities. Lithium oxide is a most attractive candidate for tritium breeding materials because of its high lithium density, high thermal conductivity and good tritium release performance. This work has been done to clarify the characteristics of tritium release and recovery from Li 2 O by means of in-situ tritium release measurement. The effects of temperature and sweep gas composition on the tritium release were investigated in this VOM-21H Experiment. Good measurement of tritium release was achieved but there were uncertainties in reproduciblity of data. The experimental results show that the role of surface adsorption/desorption makes a significant contribution to the tritium release and tritium inventory. Also, it is necessary to define the rate limiting process either diffusion or surface adsorption/desorption. (author)

New plant releases from the USDA-NRCS Aberdeen, Idaho, Plant Materials Center

Science.gov (United States)

L. St. John; P. Blaker

2001-01-01

The Plant Materials Center at Aberdeen, Idaho, is operated by the United States Department of Agriculture, Natural Resources Conservation Service. The purpose of the Plant Materials Center is to evaluate and release plant materials for conservation use and to develop and transfer new technology for the establishment and management of plants. The Center serves portions...

Electrical Switchgear Building No. 5010-ESF Fire Hazards Technical Report

International Nuclear Information System (INIS)

N.M. Ruonavaara

2001-01-01

The purpose of this Fire Hazards Analysis Technical Report (hereinafter referred to as Technical Report) is to assess the risk from fire within individual fire areas to ascertain whether the U.S. Department of Energy (DOE) fire safety objectives are met. The objectives, identified in DOE Order 420.1, Change 2, Fire Safety, Section 4.2, establish requirements for a comprehensive fire and related hazards protection program for facilities sufficient to minimize the potential for: (1) The occurrence of a fire or related event; (2) A fire that causes an unacceptable on-site or off-site release of hazardous or radiological material that will threaten the health and safety of the employees, the public, and the environment; (3) Vital DOE programs suffering unacceptable interruptions as a result of fire and related hazards; (4) Property losses from a fire and related events exceeding defined limits established by DOE; and (5) Critical process controls and safety class systems being damaged as a result of a fire and related event

[Fabrication of a new composite scaffold material for delivering rifampicin and its sustained drug release in rats].

Science.gov (United States)

Ma, Xue-Ming; Lin, Zhen; Zhang, Jia-Wei; Sang, Chao-Hui; Qu, Dong-Bin; Jiang, Jian-Ming

2016-03-01

To fabricate a new composite scaffold material as an implant for sustained delivery of rifampicin and evaluate its performance of sustained drug release and biocompatibility. The composite scaffold material was prepared by loading poly(lactic-co-glycolic) acid (PLGA) microspheres that encapsulated rifampicin in a biphasic calcium composite material with a negative surface charge. The in vitro drug release characteristics of the microspheres and the composite scaffold material were evaluated; the in vivo drug release profile of the composite scaffold material implanted in a rat muscle pouch was evaluated using high-performance liquid chromatography. The biochemical parameters of the serum and liver histopathologies of the rats receiving the transplantation were observed to assess the biocompatibility of the composite scaffold material. The encapsulation efficiency and drug loading efficiency of microspheres were (56.05±5.33)% and (29.80±2.88)%, respectively. The cumulative drug release rate of the microspheres in vitro was (94.19±5.4)% at 28 days, as compared with the rate of (82.23±6.28)% of composite scaffold material. The drug-loaded composite scaffold material showed a good performance of in vivo drug release in rats, and the local drug concentration still reached 16.18±0.35 µg/g at 28 days after implantation. Implantation of the composite scaffold material resulted in transient and reversible liver injury, which was fully reparred at 28 days after the implantation. The composite scaffold material possesses a good sustained drug release capacity and a good biocompatibility, and can serve as an alternative approach to conventional antituberculous chemotherapy.

A method for prevention of radioactive material release

International Nuclear Information System (INIS)

Uchida, Shunsuke; Sato, Chikara; Kitamura, Masao.

1975-01-01

Object: To provide a method for preventing an underwater radioactive material from being released in a simple and highly reliable manner, which can decrease an amount of radioactive materials discharged into open air from reactor water containing a large amount of radioactive materials such as a reactor core pool. Structure: Pure warm water higher in temperature than that of reactor water is poured from the top of a water surface of a water tank which stores reactor water containing radioactive materials such as radioactive iodine, and water is drawn through an outlet located downwardly of the pure warm water inlet to form a layer of pure warm water at the upper part of the water tank while preventing diffusion of the reactor water into the pure warm water by the difference in density between the reactor water and the pure warm water and downward movement of the pure warm water, thereby preventing contact of the reactor water with the atmosphere and diffusion of the radioactive material into the atmosphere. (Kamimura, M.)

A multisignal detection of hazardous materials for homeland security

Directory of Open Access Journals (Sweden)

Alamaniotis Miltiadis

2009-01-01

Full Text Available The detection of hazardous materials has been identified as one of the most urgent needs of homeland security, especially in scanning cargo containers at United States ports. To date, special nuclear materials have been detected using neutron or gamma interrogation, and recently the nuclear resonance fluorescence has been suggested. We show a new paradigm in detecting the materials of interest by a method that combines four signals (radiography/computer tomography, acoustic, muon scattering, and nuclear resonance fluorescence in cargos. The intelligent decision making software system is developed to support the following scenario: initially, radiography or the computer tomography scan is constructed to possibly mark the region(s of interest. The acoustic interrogation is utilized in synergy to obtain information regarding the ultrasonic velocity of the cargo interior. The superposition of the computer tomography and acoustic images narrows down the region(s of interest, and the intelligent system guides the detection to the next stage: no threat and finish, or proceed to the next interrogation. If the choice is the latter, knowing that high Z materials yield large scattering angle for muons, the muon scattering spectrum is used to detect the existence of such materials in the cargo. Additionally, the nuclear resonance fluorescence scan yields a spectrum that can be likened to the fingerprint of a material. The proposed algorithm is tested for detection of special nuclear materials in a comprehensive scenario.

A multisignal detection of hazardous materials for homeland security

International Nuclear Information System (INIS)

Alamaniotis, M.; Terrill, S.; Perry, J.; Gao, R.; Tsoukalas, L.; Jevremovic, T.

2009-01-01

The detection of hazardous materials has been identified as one of the most urgent needs of homeland security, especially in scanning cargo containers at United States ports. To date, special nuclear materials have been detected using neutron or gamma interrogation, and recently the nuclear resonance fluorescence has been suggested. We show a new paradigm in detecting the materials of interest by a method that combines four signals (radiography/computer tomography, acoustic, muon scattering, and nuclear resonance fluorescence) in cargos. The intelligent decision making software system is developed to support the following scenario: initially, radiography or the computer tomography scan is constructed to possibly mark the region(s) of interest. The acoustic interrogation is utilized in synergy to obtain information regarding the ultrasonic velocity of the cargo interior. The superposition of the computer tomography and acoustic images narrows down the region(s) of interest, and the intelligent system guides the detection to the next stage: no threat and finish, or proceed to the next interrogation. If the choice is the latter, knowing that high Z materials yield large scattering angle for muons, the muon scattering spectrum is used to detect the existence of such materials in the cargo. Additionally, the nuclear resonance fluorescence scan yields a spectrum that can be likened to the fingerprint of a material. The proposed algorithm is tested for detection of special nuclear materials in a comprehensive scenario. (author)

FERLENT - a controlled release fertilizer produced from a polymer material

International Nuclear Information System (INIS)

Gonzalez, Mayra; Arces, Milagros; Cuesta, Ernesto; Corredera, Pilar; Sardina, Carmen; Rieumont, Jacques; Quintana, Patricia; Bartolo, Pascual; Guenther, Bluma

2011-01-01

The possibility to use release controlled fertilizers in the agriculture of the tropical countries is more important than in the agriculture of the countries of the template regions. In this context, this work purpose the development of a new Fertilizer of Controlled Release named FERLENT, which was obtained starting from a polymeric material, under controlled conditions which allowed to corroborate the adjustment of the synthesis parameters under the modulate of nutrients liberation. It was characterized by, Scanning Microscopy Electron (SEM), Thermogravimetric analysis (TGA), Nuclear Magnetic Resonance (NMR) and infrared spectroscopy (FTIR). (author)

Sanitary Assessment of Hazardous Materials Exposed To Highly Toxic Chemical Compounds

International Nuclear Information System (INIS)

Rembovskiy, V.; Ermolaeva, E.

2007-01-01

Industrial or terroristic accidents in which toxic chemicals (TC) are the main or attendant damaging factors should be regarded as a new challenge for experts, because of little knowledge on the methodology to estimating the long-term risk for humans due to contamination of the building materials and environment. In the Russian Federation, there appeared to be a kind of model systems for developing an algorithm for solving these or similar problems. Under dismantling and liquidation of the former facilities for chemical weapon production (FCWP) the building materials are regarded as potential waste products the fate of which (processing, warehousing, utilization, and destruction) is dependent on their possible hazard for human population and environment. The standard approaches for hazard assessment of waste products of the FCWP turned out to be insufficient. When conducting the present work, the following problems have been solved: 1. Selection of representative samples taking into consideration a diversity of construction materials, great quantities of potentially toxic waste materials, information on the production conditions, breakdowns in the process of production, accidents, composition of the decontaminators used, decontamination frequency, etc. 2. Analysis of TC in composite matrixes complicated by the following problems: extraction, masking effects of concomitant components during indirect analysis, lack of certified methods of direct analysis of TC, discrepancy of results of GC and direct GCMS analysis, low sensitivity of GCMS analysis, big volume of samples (more than 0.5 kg), heterogeneity of physical-chemical properties of different matrixes influencing the process of degradation of TC. 3. Hazard assessment of the wastes in toxic-and-sanitary experiment relying on non-specific signs of intoxication due to relatively low percentage of TC and masking effects of various matrix components. Application of the integral toxicity tests with soil

Hazardous materials transportation. Part 2. Radioactive materials and wastes (citations from the NTIS Data Base). Final report for 1964--March 1978

International Nuclear Information System (INIS)

Reimherr, G.W.

1978-06-01

The bibliography cites studies on the hazards, risks, and uncertainty of transporting radioactive wastes and materials. The design of shipping containers and special labels for identification purposes for transporting fuels and wastes are also cited. Studies are included on legislation dealing with the safety and health of the population and the environmental problems associated with transporting radioactive materials

41 CFR 101-42.1101 - Federal supply classification (FSC) groups and classes which contain hazardous materials.

Science.gov (United States)

2010-07-01

..., building paper, and thermal insulation materials Asbestos cloth which has loose fibers or particles that... shipment. 5965 Headsets, handsets, microphones, and speakers Items containing magnetic material. 5970... hazardous chemicals, solvents. 6625 Electrical and electronic properties measuring and testing instruments...

Comparison of the release of constituents from granular materials under batch and column testing.

Science.gov (United States)

Lopez Meza, Sarynna; Garrabrants, Andrew C; van der Sloot, Hans; Kosson, David S

2008-01-01

Column leaching testing can be considered a better basis for assessing field impact data than any other available batch test method and thus provides a fundamental basis from which to estimate constituent release under a variety of field conditions. However, column testing is time-intensive compared to the more simplified batch testing, and may not always be a viable option when making decisions for material reuse. Batch tests are used most frequently as a simple tool for compliance or quality control reasons. Therefore, it is important to compare the release that occurs under batch and column testing, and establish conservative interpretation protocols for extrapolation from batch data when column data are not available. Five different materials (concrete, construction debris, aluminum recycling residue, coal fly ash and bottom ash) were evaluated via batch and column testing, including different column flow regimes (continuously saturated and intermittent unsaturated flow). Constituent release data from batch and column tests were compared. Results showed no significant difference between the column flow regimes when constituent release data from batch and column tests were compared. In most cases batch and column testing agreed when presented in the form of cumulative release. For arsenic in carbonated materials, however, batch testing underestimates the column constituent release for most LS ratios and also on a cumulative basis. For cases when As is a constituent of concern, column testing may be required.

Musculoskeletal symptoms and ergonomic hazards among material handlers in grocery retail industries

Science.gov (United States)

Nasrull Abdol Rahman, Mohd; Zuhaidi, Muhammad Fareez Ahmad

2017-08-01

Grocery retail work can be physically demanding as material handler’s tasks involve manual lifting, lowering, carrying, pushing and pulling loads. The nature of this work puts them at a risk for serious low back pain, shoulder pain and other musculoskeletal injuries. This study was conducted by using two different types of tools which were Nordic Musculoskeletal Questionnaire (NMQ) as a survey and Washington Industrial Safety and Health Act (WISHA) Checklist as a direct observation method. Among 46 males and 14 females material handlers were involved throughout this study. For NMQ, the highest body part trouble in the last 12 months was low back pain (88.3%), followed by upper back (68.3%), neck (55.3%) and shoulder (36.7%). While for WISHA Checklist, most of them experienced hazard level involving awkward posture and high hand force. From the research conducted, musculoskeletal disorders (MSDs) and ergonomic risk factors (ERFs) do related as it showed that musculoskeletal disorders may arise if the workers ignored the safety in ergonomic hazards.

Statistical treatment of hazards result from radioactive material in metal scrap

International Nuclear Information System (INIS)

Salem, E.F.; Rashad, S.M.

2013-01-01

Radioactive sources have a wide range of uses in medicine and industry. Radioactive materials entering the public domain in an uncontrolled manner may creating a serious risk of radiation exposure for workers and the public as well as excessive costs for plant decontamination and waste of product to be borne by the metal industry. This paper describes the major accidents that had happened in the last decades due to radioactive material in metal scrap, provides assessment of associated hazards and lessons learned. This will help Regulatory Authority to introduce measures capable to avoid the recurrence of similar events. The study highlights the situation for metal scrap incidents in Egypt.

Hazard evaluation for transfer of waste from tank 241-SY-101 to tank 241-SY-102

International Nuclear Information System (INIS)

SHULTZ, M.V.

1999-01-01

Tank 241-SY-101 (SY-101) waste level growth is an emergent, high priority issue. The purpose of this document is to record the hazards evaluation process and document potential hazardous conditions that could lead to the release of radiological and toxicological material from the proposed transfer of a limited quantity (approximately 100,000 gallons) of waste from SY-101 to 241-SY-102 (SY-102). The results of the hazards evaluation will be compared to the current Tank Waste Remediation System (TWRS) Basis for Interim Operation (HNF-SD-WM-BIO-001, 1998, Revision 1) to identify any hazardous conditions where Authorization Basis (AB) controls may not be sufficient or may not exist. Comparison to LA-UR-92-3196, A Safety Assessment for Proposed Pump Mixing Operations to Mitigate Episodic Gas Releases in Tank 241-SY-101, was also made in the case of transfer pump removal activities. This document is not intended to authorize the activity or determine the adequacy of controls; it is only intended to provide information about the hazardous conditions associated with this activity. The Unreviewed Safety Question (USQ) process will be used to determine the adequacy of controls and whether the proposed activity is within the AB. This hazard evaluation does not constitute an accident analysis

A COMPARISON: ORGANIC EMISSIONS FROM HAZARDOUS WASTE INCINERATORS VERSUS THE 1990 TOXICS RELEASE INVENTORY AIR RELEASES.

Science.gov (United States)

Incineration is often the preferred technology for disposing of hazardous waste, and remediating Superfund sites. The effective implementation of this technology is frequently impeded by strong public opposition `to hazardous waste' incineration HWI). One of the reasons cited for...

Hazardous Chemicals

Centers for Disease Control (CDC) Podcasts

2007-04-10

Chemicals are a part of our daily lives, providing many products and modern conveniences. With more than three decades of experience, The Centers for Disease Control and Prevention (CDC) has been in the forefront of efforts to protect and assess people's exposure to environmental and hazardous chemicals. This report provides information about hazardous chemicals and useful tips on how to protect you and your family from harmful exposure.  Created: 4/10/2007 by CDC National Center for Environmental Health.   Date Released: 4/13/2007.

14 CFR 1213.107 - Preventing unauthorized release of sensitive but unclassified (SBU) information/material to the...

Science.gov (United States)

2010-01-01

.../material to the news media. (a) All NASA SBU information requires accountability and approval for release... sensitive but unclassified (SBU) information/material to the news media. 1213.107 Section 1213.107 Aeronautics and Space NATIONAL AERONAUTICS AND SPACE ADMINISTRATION RELEASE OF INFORMATION TO NEWS AND...

Laser Processing of Carbon Fiber Reinforced Plastics - Release of Carbon Fiber Segments During Short-pulsed Laser Processing of CFRP

Science.gov (United States)

Walter, Juergen; Brodesser, Alexander; Hustedt, Michael; Bluemel, Sven; Jaeschke, Peter; Kaierle, Stefan

Cutting and ablation using short-pulsed laser radiation are promising technologies to produce or repair CFRP components with outstanding mechanical properties e.g. for automotive and aircraft industry. Using sophisticated laser processing strategies and avoiding excessive heating of the workpiece, a high processing quality can be achieved. However, the interaction of laser radiation and composite material causes a notable release of hazardous substances from the process zone, amongst others carbon fiber segments or fibrous particles. In this work, amounts and geometries of the released fiber segments are analyzed and discussed in terms of their hazardous potential. Moreover, it is investigated to what extent gaseous organic process emissions are adsorbed at the fiber segments, similar to an adsorption of volatile organic compounds at activated carbon, which is typically used as filter material.

Flow evaluation of the leaching hazardous materials from spent nickel-cadmium batteries discarded in different water surroundings.

Science.gov (United States)

Guo, Xingmei; Song, Yan; Nan, Junmin

2018-02-01

The leaching characteristics of hazardous materials from Ni-Cd batteries immersed in four typical water samples, i.e., water with NaCl, river water, tap water, and deionized water, were investigated to evaluate the potential environmental harm of spent Ni-Cd batteries in the water surroundings. It is shown that four water surroundings all could leach hazardous materials from the Ni-Cd batteries. The water with NaCl concentration of 66.7 mg L -1 had the highest leaching ability, the hazardous materials were leached after only approximately 50 days (average time, with a standard deviation of 4.1), while less than 100 days were needed in the others. An electrochemical corrosion is considered to be the main leaching mechanism leading to battery breakage, while the dissolution-deposition process and the powder route result in the leakage and transference of nickel and cadmium materials from the electrodes. The anions, i.e., SO 4 2- and Cl - , and dissolved oxygen in water were demonstrated to be the vital factors that influence the leaching processes. Thus, it is proposed that spent Ni-Cd batteries must be treated properly to avoid potential danger to the environment.

Conditional release of materials from decommissioning process into the environment in the form of steel railway tracks

International Nuclear Information System (INIS)

Tatransky, Peter; Necas, Vladimir

2009-01-01

This work points to the possibilities of conditional release of materials from the process of decommissioning the nuclear unit from the operation. According to the valid legislation, materials which do not meet the condition of direct-unconditional release into the environment, should be modified and processed into the matrix designed for the final disposal in the storing place. However there exists a group of materials which activity is on the borderline of the limit of releasing into the environment and it is possible to release them conditionally. The matter of conditional release is that notable amount of materials, mainly metals, is usually contaminated only by radionuclids with relatively short time of half decay. These materials are suitable to use for a specific industrial purpose where the longtime fixation of shortly living radionuclids is expected in one place. This work deals with the conditional release of metals into the form of steel railway tracks. It describes the (working) groups of workers working with the steel railway tracks and defines in the numbers the critical group and its critical individual. For critical individual it dimensions the amounts of materials, which are possible to be released conditionally from one double-unit of the plant of the type VVER 440 V-230 which operation was ended on the regular basis. According to the calculations in the software VISIPLAN and OMEGA there is defined a number of released steel in such way that the internationally recommended rate of maximal effective dose for critical individual-10 μSv/year [IAEA, 2008. Managing low radioactivity material from the decommissioning of nuclear facility. Technical reports series no. 462] is not extended. In the final part there are compared the estimates of the costs of the decommissioning process with the application of conditional release and without it, which is directly reflected in the amount of saved costs and number of containers for surface disposal.

Analyses of postulated accidental releases of UF6 inside process buildings

International Nuclear Information System (INIS)

Oliveira Neto, Jose Messias de; Nunes, Beatriz Guimaraes; Dias, Cristiane

2009-01-01

Uranium Hexafluoride is a material used in the various processes which comprise the front end of the nuclear fuel cycle (conversion, enrichment and fuel fabrication). Confinement of UF 6 is a very important safety requirement since this material is highly reactive and presents safety hazards to humans. The present paper discusses the safety relevant aspects of accidental releases of UF 6 inside process confinement buildings. Postulated accidental scenarios are analyzed and their consequences evaluated. Implant releases rates are estimated using computer code predictions. A time dependent homogeneous compartment model is used to predict concentrations of UF 6 , hydrogen fluoride and uranyl fluoride inside a confinement building, as well as to evaluate source terms released to the atmosphere. These source terms can be used as input to atmospheric dispersion models to evaluate consequences to the environment. The results can also be used to define adequate protective measures for emergency situations. (author)

Assessment of natural radioactivity and associated radiation hazards in some Cameroonian building materials

International Nuclear Information System (INIS)

Ngachin, M.; Garavaglia, M.; Giovani, C.; Kwato Njock, M.G.; Nourreddine, A.

2007-01-01

The concentration of 238 U, 232 Th and 40 K in 13 building materials obtained from factories and collected in field in Cameroon were investigated by γ-ray spectrometry. The activity ranged from 1.76 to 49.84Bqkg -1 , 0.32 to 147Bqkg -1 and 18 to 1226Bqkg -1 for 238 U, 232 Th and 40 K, respectively. The highest 238 U activity was found in compressed red soil brick type I (49.6+/-0.3Bqkg -1 ) produced by a local manufacturer while the highest 232 Th (139+/-13Bqkg -1 ) and 40 K (1162+/-108Bqkg -1 ) activities were found in gravel collected from an exploitation site in Logbadjeck. The activities are compared with available data from other investigations and with the world average value for soils. The radium equivalent activity Ra eq , the external hazard index H ex , the indoor absorbed dose rate D-bar in air and the annual effective dose equivalent E-bar were evaluated to assess the radiation hazard for people living in dwellings made of the materials studied. All building materials have shown Ra eq (range from 10 to 313Bqkg -1 ) lower than the limit of 370Bqkg -1 set in the Organization for Economic Cooperation and Development [OECD, 1979. Exposure to radiation from the natural radioactivity in building materials. OECD, Paris] report which is equivalent to a γ-dose of 1.5mSvyr -1 . Except for the gravel from Logbadjeck, all the materials examined are acceptable for use as building materials as defined by the OECD criterion

Civil nuclear: which hazards?

International Nuclear Information System (INIS)

2011-01-01

This document briefly indicates and describes the various hazards of exposure to radioactivity in relationship with the different stages of exploitation of nuclear energy: mining, exploitation, fuel reprocessing and waste management. It briefly presents and describes the scenarios associated with major risks in the exploitation phase: core fusion (description, possible origins, consequences in terms of possible releases), formation of hydrogen (chemical reaction, risk of explosion with releases, failure modes for the containment enclosure). It proposes a brief overview of consequences for mankind and for the environment due to irradiation and contamination. A brief assessment of major nuclear accidents is given, with an indication of their severity INES classification (Kyshtym, Three Mile Island, Chernobyl, Fukushima). It evokes incidents which occurred in France, and outlines the main challenges and stakes in terms of risk prevention, of plant control, of nuclear material and waste management, of public information, and of struggle against nuclear weapon proliferation. Actors and their roles are indicated: operator (EDF in France), control authority (ASN), actors in charge of waste management (ANDRA), research and information institutions (CEA, IRSN, CRIIRAD), international scientific bodies (UNSCEAR)

Risk assessment for the transportation of hazardous waste and hazardous waste components of low-level mixed waste and transuranic waste for the US Department of Energy waste management programmatic environmental impact statement

International Nuclear Information System (INIS)

Lazaro, M.A.; Policastro, A.J.; Hartmann, H.M.; Chang, Y.S.

1996-12-01

This report, a supplement to Appendix E (Transportation Risk) of the U.S. Department of Energy Waste Management Programmatic Environmental Impact Statement (WM PEIS), provides additional information supporting the accident data for chemical risk assessment and health risk methodology described in that appendix (Part II) and presents the uncertainty analysis and on-site risk calculations. This report focuses on hazardous material truck accident rates, release probabilities, and release quantities; provides the toxicological values derived for each hazardous chemical assessed in the WM PEIS and further details on the derivation of health criteria; describes the method used in the transportation risk assessments to address potential additivity of health effects from simultaneous exposure to several chemicals and the method used to address transportation risks for maximally exposed individuals; presents an expanded discussion of the uncertainty associated with transportation risk calculations; and includes the results of the on-site transportation risk analysis. In addition, two addenda are provided to detail the risk assessments conducted for the hazardous components of low-level mixed waste (Addendum I) and transuranic waste (Addendum II)

Release from control of inactive material from decommissioning the ASTRA research reactor

International Nuclear Information System (INIS)

Brandl, A.; Hrnecek, E.; Steger, F.; Kurz, H.; Meyer, F.; Karacson, P.

2003-01-01

The Austrian Research Centers Seibersdorf have been operating a 10 MW ASTRA research reactor from 1960 until 1999. After that date, a submission of the intention to decommission the reactor has been provided to the Competent Authorities. After completion of an Environmental Impact Study by the Competent Authorities and modification of the Permissions for Site Use, the reactor finally entered the decommissioning phase in 2003. Inactive materials from the decommissioning site are expected to be released from control. The procedure for such a release from control agreed upon between the Competent Authorities and ARC Seibersdorf involves a four-step measurement, verification, and certification process detailed in this paper. By September 2003, this four-step procedure has been completed for 16500 kg of steel re-enforced concrete and for 5500 kg of other materials; the release from control of 3000 kg of paraffin and 10000 kg of graphite from the thermal column are planned for the near future. (author)

Processing of hazardous material, or damage treatment method for shallow layer underground storage structure

International Nuclear Information System (INIS)

Ito, Hiroshi; Sakaguchi, Takehiko; Nishioka, Yoshihiro.

1997-01-01

In radioactive waste processing facilities and shallow layer underground structures for processing hazardous materials, sheet piles having freezing pipes at the joint portions are spiked into soils at the periphery of a damaged portion of the shallow layer underground structure for processing or storing hazardous materials. Liquid nitrogen is injected to the freezing pipes to freeze the joint portions of adjacent sheet piles. With such procedures, continuous waterproof walls are formed surrounding the soils at the peripheries of the damaged portion. Further, freezing pipes are disposed in the surrounding soils, and liquid nitrogen is injected to freeze the soils. The frozen soils are removed, and artificial foundation materials are filled in the space except for the peripheries of the damaged portion after the removal thereof, and liquid suspension is filled in the peripheries of the damaged portion, and restoration steps for closing the damaged portion are applied. Then, the peripheries of the damaged portion are buried again. With such procedures, series of treatments for removing contaminated soils and repairing a damaged portion can be conducted efficiently at a low cost. (T.M.)

Multiple external hazards compound level 3 PSA methods research of nuclear power plant

Science.gov (United States)

Wang, Handing; Liang, Xiaoyu; Zhang, Xiaoming; Yang, Jianfeng; Liu, Weidong; Lei, Dina

2017-01-01

2011 Fukushima nuclear power plant severe accident was caused by both earthquake and tsunami, which results in large amount of radioactive nuclides release. That accident has caused the radioactive contamination on the surrounding environment. Although this accident probability is extremely small, once such an accident happens that is likely to release a lot of radioactive materials into the environment, and cause radiation contamination. Therefore, studying accidents consequences is important and essential to improve nuclear power plant design and management. Level 3 PSA methods of nuclear power plant can be used to analyze radiological consequences, and quantify risk to the public health effects around nuclear power plants. Based on multiple external hazards compound level 3 PSA methods studies of nuclear power plant, and the description of the multiple external hazards compound level 3 PSA technology roadmap and important technical elements, as well as taking a coastal nuclear power plant as the reference site, we analyzed the impact of off-site consequences of nuclear power plant severe accidents caused by multiple external hazards. At last we discussed the impact of off-site consequences probabilistic risk studies and its applications under multiple external hazards compound conditions, and explained feasibility and reasonableness of emergency plans implementation.

Increasing worker and community awareness of toxic hazards in the workplace.

Science.gov (United States)

1985-03-01

In November 1984, the Governing Council of the American Public Health Association (APHA) released this position paper on disclosure of occupational health hazards. The Council's action was prompted by the Occupational Health and Safety Administration's (OSHA's) promulgation of a national right-to-know standard that would pre-empt stronger state and local laws protecting an employee's right to be told about hazardous materials in the workplace. The APHA document outlines the dimensions of the toxic substances problem in the United States; argues the need for right-to-know laws; defines the roles of OSHA, unions, and local coalitions for workplace safety; and criticizes the Federal Hazard Communication Standard. Lists of ten essential components of a national right-to-know policy and of four actions the APHA will take to further the worker's right-to-know conclude the paper.

Determining cutoff distances for assessing risks from transportation accident radiation releases

International Nuclear Information System (INIS)

Sandquist, G.M.; Slaughter, D.M.; Kimura, C.Y.; Brumburgh, G.

1995-01-01

The transportation of radioactive materials throughout the United States and the world is a ubiquitous and sometimes controversial activity. Almost universally, these transportation activities have been performed without major incident, and the safety record for transportation of radioactive material is outstanding compared with the transportation of other hazardous materials. Nevertheless, concerns still exist regarding adequate regulation of radioactive material transportation and accurate assessment of the health risks associated with accidents. These concerns are addressed through certification by the cognizant regulatory authority over the transportation container or the performance of a transportation risk assessment. In a transportation risk assessment, accident situations are examined, frequencies are estimated, and consequences resulting from the accident are analyzed and evaluated for acceptance. A universal question with any transportation risk assessment that examines the radiological consequences from release accidents is, At what distance may the dispersion analysis be terminated? This paper examines cutoff distances and their consequences for assessing health risks from radiological transportation releases

Risk assessment for the transportation of hazardous waste and hazardous waste components of low-level mixed waste and transuranic waste for the U.S. Department of Energy waste management programmatic environmental impact statement

International Nuclear Information System (INIS)

Lazaro, M.A.; Policastro, A.J.; Hartmann, H.M.

1995-04-01

This report, a supplement to Appendix E (Transportation Risk) of the U.S. Department of Energy Waste Management Programmatic Environmental Impact Statement (WM PEIS), provides additional information supporting the accident data for chemical risk assessment and health risk methodology described in that appendix (Part II), as well as providing the uncertainty analysis and on-site risk calculations. This report focuses on hazardous material truck accident rates, release probabilities, and release quantities; provides the toxicological values derived for each hazardous chemical assessed in the WM PEIS and further details on the derivation of health criteria; describes the method used in the transportation risk assessments to address potential additivity of health effects from simultaneous exposure to several chemicals and the method used to address transportation risks for maximally exposed individuals; presents an expanded discussion of the uncertainty associated with transportation risk calculations; and includes the results of the on-site transportation risk analysis. In addition, two addenda are provided to detail the risk assessments conducted for the hazardous components of low-level mixed waste (Addendum I) and transuranic waste (Addendum II)

A Risk Assessment Model for Water Resources: releases of dangerous and hazardous substances.

Science.gov (United States)

Rebelo, Anabela; Ferra, Isabel; Gonçalves, Isolina; Marques, Albertina M

2014-07-01

Many dangerous and hazardous substances are used, transported and handled daily in diverse situations, from domestic use to industrial processing, and during those operations, spills or other anomalous situations may occur that can lead to contaminant releases followed by contamination of surface water or groundwater through direct or indirect pathways. When dealing with this problem, rapid, technically sound decisions are desirable, and the use of complex methods may not be able to deliver information quickly. This work describes a simple conceptual model established on multi-criteria based analysis involving a strategic appraisal for contamination risk assessment to support local authorities on rapid technical decisions. The model involves a screening for environmental risk sources, focussing on persistent, bioaccumulative and toxic (PBT) substances that may be discharged into water resources. It is a simple tool that can be used to follow-up actual accident scenarios in real time and to support daily activities, such as site-inspections. Copyright © 2014 Elsevier Ltd. All rights reserved.

Hazard evaluation for transfer of waste from tank 241-SY-101 to tank 241-SY-102

International Nuclear Information System (INIS)

Shultz, M.V.

1999-01-01

Tank 241-SY-101 waste level growth is an emergent, high priority issue. The purpose of this document is to record the hazards evaluation process and document potential hazardous conditions that could lead to the release of radiological and toxicological material from the proposed transfer of a limited quantity (approximately 100,000 gallons) of waste from Tank 241-SY-101 to Tank 241-SY-102. The results of the hazards evaluation were compared to the current Tank Waste Remediation System (TWRS) Basis for Interim Operation (HNF-SD-WM-BIO-001, 1998, Revision 1) to identify any hazardous conditions where Authorization Basis (AB) controls may not be sufficient or may not exist. Comparison to LA-UR-92-3196, A Safety Assessment for Proposed Pump Mixing Operations to Mitigate Episodic Gas Releases in Tank 241-SY-101, was also made in the case of transfer pump removal activities. Revision 1 of this document deletes hazardous conditions no longer applicable to the current waste transfer design and incorporates hazardous conditions related to the use of an above ground pump pit and overground transfer line. This document is not part of the AB and is not a vehicle for requesting authorization of the activity; it is only intended to provide information about the hazardous conditions associated with this activity. The AB Control Decision process will be used to determine the adequacy of controls and whether the proposed activity is within the AB. This hazard evaluation does not constitute an accident analysis

Radioactive materials released from nuclear power plants. Annual report, 1982. Volume 3

International Nuclear Information System (INIS)

Tichler, J.; Norden, K.

1986-02-01

Releases of radioactive materials in airborne and liquid effluents from commercial light water reactors during 1982 have been compiled and reported. Data on solid waste shipments as well as selected operating information have been included. This report supplements earlier annual reports issued by the former Atomic Energy Commission and the Nuclear Regulatory Commission. The 1982 release data are summarized in tabular form. Data covering specific radionuclides are summarized

Materials for Pharmaceutical Dosage Forms: Molecular Pharmaceutics and Controlled Release Drug Delivery Aspects

Directory of Open Access Journals (Sweden)

Patrick P. DeLuca

2010-09-01

Full Text Available Controlled release delivery is available for many routes of administration and offers many advantages (as microparticles and nanoparticles over immediate release delivery. These advantages include reduced dosing frequency, better therapeutic control, fewer side effects, and, consequently, these dosage forms are well accepted by patients. Advances in polymer material science, particle engineering design, manufacture, and nanotechnology have led the way to the introduction of several marketed controlled release products and several more are in pre-clinical and clinical development.

Regulatory analysis on criteria for the release of patients administered radioactive material

International Nuclear Information System (INIS)

Schneider, S.; McGuire, S.A.

1994-05-01

The Nuclear Regulatory Commission (NRC) has received two petitions to amend its regulations in 10 CFR Parts 20 and 35 as they apply to doses received by members of the public exposed to patients released from a hospital after they have been administered radioactive material. While the two petitions are not identical they both request that the NRC establish a dose limit of 5 millisieverts (0.5 rem) per year for individuals exposed to patients who have been administered radioactive materials. This Regulatory Analysis evaluates three alternatives. Alternative 1 is for the NRC to amend its patient release criteria in 10 CFR 35.75 to use the more stringent dose limit of 1 millisievert per year in 10 CFR 20.1301(a) for its patient release criteria. Alternative 2 is for the NRC to continue using the existing patient release criteria in 10 CFR 35.75 of 1,110 megabecquerels of activity or a dose rate at one meter from the patient of 0.05 millisievert per hour. Alternative 3 is for the NRC to amend the patient release criteria in 10 CFR 35.75 to specify a dose limit of 5 millisieverts for patient release. The evaluation indicates that Alternative 1 would cause a prohibitively large increase in the national health care cost from retaining patients in a hospital longer and would cause significant personal and psychological costs to patients and their families. The choice of Alternatives 2 or 3 would affect only thyroid cancer patients treated with iodine-131. For those patients, Alternative 3 would result in less hospitalization than Alternative 2. Alternative 3 has a potential decrease in national health care cost of $30,000,000 per year but would increase the potential collective dose from released therapy patients by about 2,700 person-rem per year, mainly to family members

Regulatory analysis on criteria for the release of patients administered radioactive material

Energy Technology Data Exchange (ETDEWEB)

Schneider, S.; McGuire, S.A. [Nuclear Regulatory Commission, Washington, DC (United States). Div. of Regulatory Applications; Behling, U.H.; Behling, K.; Goldin, D. [Cohen (S.) and Associates, Inc., McLean, VA (United States)

1994-05-01

The Nuclear Regulatory Commission (NRC) has received two petitions to amend its regulations in 10 CFR Parts 20 and 35 as they apply to doses received by members of the public exposed to patients released from a hospital after they have been administered radioactive material. While the two petitions are not identical they both request that the NRC establish a dose limit of 5 millisieverts (0.5 rem) per year for individuals exposed to patients who have been administered radioactive materials. This Regulatory Analysis evaluates three alternatives. Alternative 1 is for the NRC to amend its patient release criteria in 10 CFR 35.75 to use the more stringent dose limit of 1 millisievert per year in 10 CFR 20.1301(a) for its patient release criteria. Alternative 2 is for the NRC to continue using the existing patient release criteria in 10 CFR 35.75 of 1,110 megabecquerels of activity or a dose rate at one meter from the patient of 0.05 millisievert per hour. Alternative 3 is for the NRC to amend the patient release criteria in 10 CFR 35.75 to specify a dose limit of 5 millisieverts for patient release. The evaluation indicates that Alternative 1 would cause a prohibitively large increase in the national health care cost from retaining patients in a hospital longer and would cause significant personal and psychological costs to patients and their families. The choice of Alternatives 2 or 3 would affect only thyroid cancer patients treated with iodine-131. For those patients, Alternative 3 would result in less hospitalization than Alternative 2. Alternative 3 has a potential decrease in national health care cost of $30,000,000 per year but would increase the potential collective dose from released therapy patients by about 2,700 person-rem per year, mainly to family members.

Use of the Hazard Prediction and Assessment Capability (HPAC) at the Savannah River Site

International Nuclear Information System (INIS)

BUCKLEY, ROBERT

2004-01-01

This report provides background information on the implementation of the Hazard Prediction and Assessment Capability (HPAC) software package at the Savannah River Site for atmospheric modeling. Developed by the Defense Threat Reduction Agency (DTRA), HPAC is actually a suite of models that allows for various modes of release of radiological, chemical and biological agents, generates interpolated meteorological data fields based on inputted meteorology, and transports the material using a tested transport and diffusion model. A discussion of meteorological data availability for direct use by HPAC is given, and is important for applications to emergency response. An evaluation of the data input methodology for a release from SRS is examined, as well as an application to the World Trade Center attacks in New York City in September 2001. Benefits of the newer versions of HPAC now in use are then discussed. These include access to more meteorological data sources and improved graphical cap abilities. The HPAC software package is another tool to help the Atmospheric Technologies Group (ATG) provide atmospheric transport and dispersion predictions in the event of hazardous atmospheric releases

Kauai Test Facility hazards assessment document

Energy Technology Data Exchange (ETDEWEB)

Swihart, A

1995-05-01

The Department of Energy Order 55003A requires facility-specific hazards assessment be prepared, maintained, and used for emergency planning purposes. This hazards assessment document describes the chemical and radiological hazards associated with the Kauai Test Facility, Barking Sands, Kauai, Hawaii. The Kauai Test Facility`s chemical and radiological inventories were screened according to potential airborne impact to onsite and offsite individuals. The air dispersion model, ALOHA, estimated pollutant concentrations downwind from the source of a release, taking into consideration the toxicological and physical characteristics of the release site, the atmospheric conditions, and the circumstances of the release. The greatest distance to the Early Severe Health Effects threshold is 4.2 kilometers. The highest emergency classification is a General Emergency at the {open_quotes}Main Complex{close_quotes} and a Site Area Emergency at the Kokole Point Launch Site. The Emergency Planning Zone for the {open_quotes}Main Complex{close_quotes} is 5 kilometers. The Emergency Planning Zone for the Kokole Point Launch Site is the Pacific Missile Range Facility`s site boundary.

Kauai Test Facility hazards assessment document

International Nuclear Information System (INIS)

Swihart, A.

1995-05-01

The Department of Energy Order 55003A requires facility-specific hazards assessment be prepared, maintained, and used for emergency planning purposes. This hazards assessment document describes the chemical and radiological hazards associated with the Kauai Test Facility, Barking Sands, Kauai, Hawaii. The Kauai Test Facility's chemical and radiological inventories were screened according to potential airborne impact to onsite and offsite individuals. The air dispersion model, ALOHA, estimated pollutant concentrations downwind from the source of a release, taking into consideration the toxicological and physical characteristics of the release site, the atmospheric conditions, and the circumstances of the release. The greatest distance to the Early Severe Health Effects threshold is 4.2 kilometers. The highest emergency classification is a General Emergency at the open-quotes Main Complexclose quotes and a Site Area Emergency at the Kokole Point Launch Site. The Emergency Planning Zone for the open-quotes Main Complexclose quotes is 5 kilometers. The Emergency Planning Zone for the Kokole Point Launch Site is the Pacific Missile Range Facility's site boundary

Release protocol to address DOE moratorium on shipments of waste generated in radiologically controlled areas

International Nuclear Information System (INIS)

Rathbun, L.A.; Boothe, G.F.

1992-10-01

On May 17, 1991 the US DOE Office of Waste Operations issued a moratorium on the shipment of hazardous waste from radiologically contaminated or potentially contaminated areas on DOE sites to offsite facilities not licensed for radiological material. This document describes a release protocol generated by Westinghouse Hanford submitted for US DOE approval. Topics considered include designating Radiological Materials Management Areas (RMMAs), classification of wastes, handling of mixed wastes, detection limits

40 CFR 260.43 - Legitimate recycling of hazardous secondary materials regulated under § 260.34, § 261.2(a)(2)(ii...

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 25 2010-07-01 2010-07-01 false Legitimate recycling of hazardous... (CONTINUED) HAZARDOUS WASTE MANAGEMENT SYSTEM: GENERAL Rulemaking Petitions § 260.43 Legitimate recycling of... demonstrate that the recycling is legitimate. Hazardous secondary material that is not legitimately recycled...

Estimated airborne release of radionuclides from the Battelle Memorial Institute Columbus Laboratories JN-1b building at the West Jefferson site as a result of postulated damage from severe wind and earthquake hazard

International Nuclear Information System (INIS)

Mishima, J.; Ayer, J.E.

1981-11-01

The potential airborne releases of radionuclides (source terms) that could result from wind and earthquake dmage are estimated for the Battelle Memorial Institute Columbus Laboratories JN-1b Building at the West Jefferson site in Ohio. The estimated source terms are based on the damage to barriers containing the radionuclides, the inventory of radionuclides at risk, and the fraction of the inventory made airborne as a result of the loss of containment. In an attempt to provide a realistic range of potential source terms that include most of the normal operating conditions, a best estimate bounded by upper and lower limits is calculated by combining the upper-bound, best-estimate, and lower-bound inventories-at-risk with an airborne release factor (upper-bound, best-estimate, and lower-bound if possible) for the situation. The factors used to evaluate the fractional airborne release of materials and the exchange rates between enclosed and exterior atmospheres are discussed. The postulated damage and source terms are discussed for wind and earthquake hazard scenarios in order of their increasing severity

Temperature-regulated guest admission and release in microporous materials

Science.gov (United States)

Li, Gang (Kevin); Shang, Jin; Gu, Qinfen; Awati, Rohan V.; Jensen, Nathan; Grant, Andrew; Zhang, Xueying; Sholl, David S.; Liu, Jefferson Z.; Webley, Paul A.; May, Eric F.

2017-06-01

While it has long been known that some highly adsorbing microporous materials suddenly become inaccessible to guest molecules below certain temperatures, previous attempts to explain this phenomenon have failed. Here we show that this anomalous sorption behaviour is a temperature-regulated guest admission process, where the pore-keeping group's thermal fluctuations are influenced by interactions with guest molecules. A physical model is presented to explain the atomic-level chemistry and structure of these thermally regulated micropores, which is crucial to systematic engineering of new functional materials such as tunable molecular sieves, gated membranes and controlled-release nanocontainers. The model was validated experimentally with H2, N2, Ar and CH4 on three classes of microporous materials: trapdoor zeolites, supramolecular host calixarenes and metal-organic frameworks. We demonstrate how temperature can be exploited to achieve appreciable hydrogen and methane storage in such materials without sustained pressure. These findings also open new avenues for gas sensing and isotope separation.

Assessment of the Grouted IXC Monolith in Support of K East Basin Hazard Categorization

Energy Technology Data Exchange (ETDEWEB)

Short, Steven M.; Dodson, Michael G.; Alzheimer, James M.; Meyer, Perry A.

2007-10-12

Addendum to original report updating the structural analysis of the I-beam accident to reflect a smaller I-beam than originally assumed (addendum is 2 pages). The K East Basin currently contains six ion exchange columns (IXCs) that were removed from service over 10 years ago. Fluor Hanford plans to immobilize the six ion exchange columns (IXCs) in place in a concrete monolith. PNNL performed a structural assessment of the concrete monolith to determine its capability to absorb the forces imposed by postulated accidents and protect the IXCs from damage and thus prevent a release of radioactive material. From this assessment, design specifications for the concrete monolith were identified that would prevent a release of radioactive material for any of the postulated hazardous conditions.

Analysis of chromium and sulphate origins in construction recycled materials based on leaching test results.

Science.gov (United States)

Del Rey, I; Ayuso, J; Galvín, A P; Jiménez, J R; López, M; García-Garrido, M L

2015-12-01

Twenty samples of recycled aggregates from construction and demolition waste (CDW) with different compositions collected at six recycling plants in the Andalusia region (south of Spain) were characterised according to the Landfill Directive criteria. Chromium and sulphate were identified as the most critical compounds in the leachates. To detect the sources of these two pollutant constituents in recycled aggregate, environmental assessments were performed on eight construction materials (five unused ceramic materials, two old crushed concretes and one new mortar manufactured in the laboratory). The results confirmed that leached sulphate and Cr were mainly released by the ceramic materials (bricks and tiles). To predict the toxicological consequences, the oxidation states of Cr (III) and Cr (VI) were measured in the leachates of recycled aggregates and ceramic materials classified as non-hazardous. The bricks and tiles mainly released total Cr as Cr (III). However, the recycled aggregates classified as non-hazardous according to the Landfill Directive criteria mainly released Cr (VI), which is highly leachable and extremely toxic. The obtained results highlight the need for legislation that distinguishes the oxidative state in which chromium is released into the environment. Leaching level regulations must not be based solely on total Cr, which can lead to inaccurate predictions. Copyright © 2015 Elsevier Ltd. All rights reserved.

Climate Prediction Center (CPC) U.S. Hazards Outlook

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Climate Prediction Center releases a US Hazards Outlook daily, Monday through Friday. The product highlights regions of anticipated hazardous weather during the...

Simulation Technology Laboratory Building 970 hazards assessment document

International Nuclear Information System (INIS)

Wood, C.L.; Starr, M.D.

1994-11-01

The Department of Energy Order 5500.3A requires facility-specific hazards assessments be prepared, maintained, and used for emergency planning purposes. This hazards assessment document describes the chemical and radiological hazards associated with the Simulation Technology Laboratory, Building 970. The entire inventory was screened according to the potential airborne impact to onsite and offsite individuals. The air dispersion model, ALOHA, estimated pollutant concentrations downwind from the source of a release, taking into consideration the toxicological and physical characteristics of the release site, the atmospheric conditions, and the circumstances of the release. The greatest distances at which a postulated facility event will produce consequences exceeding the ERPG-2 and Early Severe Health Effects thresholds are 78 and 46 meters, respectively. The highest emergency classification is a Site Area Emergency. The Emergency Planning Zone is 100 meters

Two Chaotic Patterns of Dynamic Risk Definition for Solving Hazardous Materials Routing Problem

Directory of Open Access Journals (Sweden)

Abbas Mahmoudabadi

2015-01-01

Full Text Available In the case of determining routes for hazardous material transportation, risk is considered as a main attribute. Transport risk, which is usually combined with other attributes such as cost or travel time, plays a significant role in determining paths for hazardous materials transportation. Since, risk is chaotically affected by road incidents, decision makers are dealing with selecting a method for defining chaotic risk factors in hazmat transportation. In this paper, transport risk has been defined as a chaotic variable using two different methods of generating chaotic patterns. In an experimental road network, which consists of eighty-nine nodes and one hundred and one two-way links, two different methods of generating chaotic variables have been used for applying the proposed procedure. In addition, results for different amounts of risk and cost have also been analyzed in case study. Results revealed that different cost and risk priorities change the frequencies of selected paths determined for hazmat transportation, but the route convergence of the route to chaos method is better than that of the logistic map equation.

Accident analysis for aircraft crash into hazardous facilities: DOE standard

International Nuclear Information System (INIS)

1996-10-01

This standard provides the user with sufficient information to evaluate and assess the significance of aircraft crash risk on facility safety without expending excessive effort where it is not required. It establishes an approach for performing a conservative analysis of the risk posed by a release of hazardous radioactive or chemical material resulting from an aircraft crash into a facility containing significant quantities of such material. This can establish whether a facility has a significant potential for an aircraft impact and whether this has the potential for producing significant offsite or onsite consequences. General implementation guidance, screening and evaluation guidelines, and methodologies for the evaluations are included

Hazardous materials safety and security technology field operational test. Volume II, evaluation final report synthesis

Science.gov (United States)

2004-11-11

The catastrophic events of September 11, 2001 and the ongoing war on terrorism have heightened the level of concern from Federal government officials and the transportation industry regarding the secure transport of hazardous materials (HAZMAT). Secu...

A Comparison of Organic Emissions from Hazardous Waste Incinerators Versus the 1990 Toxics Release Inventory Air Releases

Science.gov (United States)

Incineration is often the preferred technology for disposing of hazardous waste and remediating Superfund sites. The effective implementation of this technology is frequently impeded by strong public opposition to hazardous waste incineration (HWI). One of the reasons cited for t...

An evaluation of trace element release associated with acid mine drainage

International Nuclear Information System (INIS)

Sullivan, P.J.; Yelton, J.L.

1988-01-01

The determination of trace element release from geologic materials, such as oil shale and coal overburden, is important for proper solid waste management planning. The objective of this study was to determine a correlation between release using the following methods: (1) sequential selective dissolution for determining trace element residencies, (2) toxicity characteristic leaching procedure (TCLP), and (3) humidity cell weathering study simulating maximum trace element release. Two eastern oil shales were used, a New Albany shale that contains 4.6 percent pyrite, and a Chattanooga shale that contains 1.5 percent pyrite. Each shale was analyzed for elemental concentrations by soluble, adsorbed, organic, carbonate, and sulfide phases. The results of the results of the selective dissolution studies show that each trace element has a unique distribution between the various phases. Thus, it is possible to predict trace element release based on trace element residency. The TCLP results show that this method is suitable for assessing soluble trace element release but does not realistically assess potential hazards. The results of the humidity cell studies do demonstrate a more reasonable method for predicting trace element release and potential water quality hazards. The humidity cell methods, however, require months to obtain the required data with a large number of analytical measurements. When the selective dissolution data are compared to the trace element concentrations in the TCLP and humidity cell leachates, it is shown that leachate concentrations are predicted by the selective dissolution data. Therefore, selective dissolution may represent a rapid method to assess trace element release associated with acid mine drainage

Controlled release of non-steroidal antiinflammatory and anticancer drugs from hybrid materials

International Nuclear Information System (INIS)

Caravieri, Beatriz Bernardes; Molina, Eduardo Ferreira

2016-01-01

Full text: Chronic inflammation is a well known risk factor for the development of human cancer, and at least one third of all human cancers have been associated with inflammation. This can lead to cellular proliferation, a process which per se increases the risk of abnormal cell formation and ultimately the development of cancer. For treating clinical conditions such as inflammation and cancer, the most common methods (e.g., oral administration, injection) can cause unwanted side effects due to drug delivery to non-target sites and the introduction of high doses of the drug to reach the desired location. An alternative to these problems is the preparation of materials that can release drugs with different activities. Thinking about it, the aim of this study was to use a class of hybrid materials based on siloxane-polyether known as ureasil for controlled release of non-steroidal anti-inflammatory drugs (NSAIDs) such as ibuprofen (IBU) and naproxen (NAP), and anticancer, such as 5-fluorouracil (5- FU). These drugs have been incorporated in the matrix in different proportions and thereafter, were characterized by different techniques such as XRD, FTIR, DSC and SAXS. In addition, it has been evaluated the release kinetics of these species with different chemical structures. The results have shown that the drug molecules were homogeneously distributed in the xerogel hybrids, which contributed to the drug’s release profile fine-tuning. The chemical environment of the polyether chains was amended by incorporating the drugs. The analysis from XRD, FTIR, SAXS and DSC confirm the good solubility of the substances within hybrid matrix. This hybrid material based on polymers and inorganic compounds may have potential applications in human health. (author)

Controlled release of non-steroidal antiinflammatory and anticancer drugs from hybrid materials

Energy Technology Data Exchange (ETDEWEB)

Caravieri, Beatriz Bernardes; Molina, Eduardo Ferreira, E-mail: bia_ms_@hotmail.com [Universidade de Franca, SP (Brazil)

2016-07-01

Full text: Chronic inflammation is a well known risk factor for the development of human cancer, and at least one third of all human cancers have been associated with inflammation. This can lead to cellular proliferation, a process which per se increases the risk of abnormal cell formation and ultimately the development of cancer. For treating clinical conditions such as inflammation and cancer, the most common methods (e.g., oral administration, injection) can cause unwanted side effects due to drug delivery to non-target sites and the introduction of high doses of the drug to reach the desired location. An alternative to these problems is the preparation of materials that can release drugs with different activities. Thinking about it, the aim of this study was to use a class of hybrid materials based on siloxane-polyether known as ureasil for controlled release of non-steroidal anti-inflammatory drugs (NSAIDs) such as ibuprofen (IBU) and naproxen (NAP), and anticancer, such as 5-fluorouracil (5- FU). These drugs have been incorporated in the matrix in different proportions and thereafter, were characterized by different techniques such as XRD, FTIR, DSC and SAXS. In addition, it has been evaluated the release kinetics of these species with different chemical structures. The results have shown that the drug molecules were homogeneously distributed in the xerogel hybrids, which contributed to the drug’s release profile fine-tuning. The chemical environment of the polyether chains was amended by incorporating the drugs. The analysis from XRD, FTIR, SAXS and DSC confirm the good solubility of the substances within hybrid matrix. This hybrid material based on polymers and inorganic compounds may have potential applications in human health. (author)

Scenarios and methods that induce protruding or released CNTs after degradation of nanocomposite materials.

Science.gov (United States)

Hirth, Sabine; Cena, Lorenzo; Cox, Gerhard; Tomović, Zeljko; Peters, Thomas; Wohlleben, Wendel

2013-04-01

Nanocomposite materials may be considered as a low-risk application of nanotechnology, if the nanofillers remain embedded throughout the life-cycle of the products in which they are embedded. We hypothesize that release of free CNTs occurs by a combination of mechanical stress and chemical degradation of the polymer matrix. We experimentally address limiting cases: Mechanically released fragments may show tubular protrusions on their surface. Here we identify these protrusions unambiguously as naked CNTs by chemically resolved microscopy and a suitable preparation protocol. By size-selective quantification of fragments we establish as a lower limit that at least 95 % of the CNTs remain embedded. Contrary to classical fiber composite approaches, we link this phenomenon to matrix materials with only a few percent elongation at break, predicting which materials should still cover their CNT nanofillers after machining. Protruding networks of CNTs remain after photochemical degradation of the matrix, and we show that it takes the worst case combinations of weathering plus high-shear wear to release free CNTs in the order of mg/m 2 /year. Synergy of chemical degradation and mechanical energy input is identified as the priority scenario of CNT release, but its lab simulation by combined methods is still far from real-world validation.

An overview of safety assessment, regulation, and control of hazardous material use at NREL

Science.gov (United States)

Nelson, B. P.; Crandall, R. S.; Moskowitz, P. D.; Fthenakis, V. M.

1992-12-01

This paper summarizes the methodology we use to ensure the safe use of hazardous materials at the National Renewable Energy Laboratory (NREL). First, we analyze the processes and the materials used in those processes to identify the hazards presented. Then we study federal, state, and local regulations and apply the relevant requirements to our operations. When necessary, we generate internal safety documents to consolidate this information. We design research operations and support systems to conform to these requirements. Before we construct the systems, we perform a semiquantitative risk analysis on likely accident scenarios. All scenarios presenting an unacceptable risk require system or procedural modifications to reduce the risk. Following these modifications, we repeat the risk analysis to ensure that the respective accident scenarios present an acceptable risk. Once all risks are acceptable, we conduct an operational readiness review (ORR). A management-appointed panel performs the ORR ensuring compliance with all relevant requirements. After successful completion of the ORR, operations can begin.

An overview of safety assessment, regulation, and control of hazardous material use at NREL

International Nuclear Information System (INIS)

Nelson, B.P.; Crandall, R.S.; Moskowitz, P.D.; Fthenakis, V.M.

1992-01-01

This paper summarizes the methodology we use to ensure the safe use of hazardous materials at the National Renewable Energy Laboratory (NREL). First, we analyze the processes and the materials used in those processes to identify the hazards presented. Then we study federal, state, and local regulations and apply the relevant requirements to our operations. When necessary, we generate internal safety documents to consolidate this information. We design research operations and support systems to conform to these requirements. Before we construct the systems, we perform a semiquantitative risk analysis on likely accident scenarios. All scenarios presenting in unacceptable risk require system or procedural modifications to reduce the risk. Following these modifications, we repeat the risk analysis to ensure that the respective accident scenarios present acceptable risk. Once all risks are acceptable, we conduct an operational readiness review (ORR). A management appointed panel performs the ORR ensuring compliance with all relevant requirements. After successful completion of the ORR, operations can begin

An overview of safety assessment, regulation, and control of hazardous material use at NREL

International Nuclear Information System (INIS)

Nelson, B.P.; Crandall, R.S.; Moskowitz, P.D.; Fthenakis, V.M.

1992-01-01

This paper summarizes the methodology we use to ensure the safe use of hazardous materials at the National Renewable Energy Laboratory (NREL). First, we analyze the processes and the materials used in those processes to identify the hazards presented. Then we study federal, state, and local regulations and apply the relevant requirements to our operations. When necessary, we generate internal safety documents to consolidate this information. We design research operations and support systems to conform to these requirements. Before we construct the systems, we perform a semiquantitative risk analysis on likely accident scenarios. All scenarios presenting an unacceptable risk require system or procedural modifications to reduce the risk. Following these modifications, we repeat the risk analysis to ensure that the respective accident scenarios present an acceptable risk. Once all risks are acceptable, we conduct an operational readiness review (ORR). A management-appointed panel performs the ORR ensuring compliance with all relevant requirements. After successful completion of the ORR, operations can begin

Minutes of the workshop on off-site release criteria for contaminated materials

International Nuclear Information System (INIS)

Singh, S.P.N.

1989-11-01

A one and one-half-day workshop was held May 2-3, 1989, at the Pollard Auditorium in Oak Ridge, Tennessee, with the objective of formulating a strategy for developing reasonable and uniform criteria for releasing radioactively contaminated materials from the US Department of Energy (DOE) sites. This report contains the minutes of the workshop. At the conclusion of the workshop, a plan was formulated to facilitate the development of the above-mentioned off-site release criteria

Calculation of releases of radioactive materials in gaseous effluents from nuclear-powered merchant ships (NMS-GEFF code)

International Nuclear Information System (INIS)

Cardile, F.P.; Bangart, R.L.; Collins, J.T.

1978-06-01

The Intergovernmental Maritime Consultative Organization IMCO) is currently preparing guidelines concerning the safety of nuclear-powered merchant ships. An important aspect of these guidelines is the determination of the releases of radioactive material in effluents from these ships and the control exercised by the ships over these releases. To provide a method for the determination of these releases, the NRC staff has developed a computerized model, the NMS-GEFF Code, which is described in the following chapters. The NMS-GEFF Code calculates releases of radioactive material in gaseous effluents for nuclear-powered merchant ships using pressurized water reactors

Assessment of natural radioactivity and associated radiation hazards in some Cameroonian building materials

Energy Technology Data Exchange (ETDEWEB)

Ngachin, M. [Center for Atomic, Molecular Physics and Quantum Optics, University of Douala, P.O. Box 8580, Douala (Cameroon) and Abdus Salam International Center for Theoretical Physics, Strada Costiera 11, 34014 Trieste (Italy)]. E-mail: mngachin@yahoo.com; Garavaglia, M. [Regional Agency for Environmental Protection (ARPA), 91 via Tavagnacco, 33100 Udine (Italy); Giovani, C. [Regional Agency for Environmental Protection (ARPA), 91 via Tavagnacco, 33100 Udine (Italy); Kwato Njock, M.G. [Center for Atomic, Molecular Physics and Quantum Optics, University of Douala, P.O. Box 8580, Douala (Cameroon); Nourreddine, A. [Institut Pluridisciplinaire Hubert Curien, UMR7500 CNRS-IN2P3 et Universite Louis Pasteur, 23 Rue du Loess, BP 28, F-67037, Strasbourg Cedex 2 (France)

2007-01-15

The concentration of {sup 238}U, {sup 232}Th and {sup 40}K in 13 building materials obtained from factories and collected in field in Cameroon were investigated by {gamma}-ray spectrometry. The activity ranged from 1.76 to 49.84Bqkg{sup -1}, 0.32 to 147Bqkg{sup -1} and 18 to 1226Bqkg{sup -1} for {sup 238}U, {sup 232}Th and {sup 40}K, respectively. The highest {sup 238}U activity was found in compressed red soil brick type I (49.6+/-0.3Bqkg{sup -1}) produced by a local manufacturer while the highest {sup 232}Th (139+/-13Bqkg{sup -1}) and {sup 40}K (1162+/-108Bqkg{sup -1}) activities were found in gravel collected from an exploitation site in Logbadjeck. The activities are compared with available data from other investigations and with the world average value for soils. The radium equivalent activity Ra{sub eq}, the external hazard index H{sub ex}, the indoor absorbed dose rate D-bar in air and the annual effective dose equivalent E-bar were evaluated to assess the radiation hazard for people living in dwellings made of the materials studied. All building materials have shown Ra{sub eq} (range from 10 to 313Bqkg{sup -1}) lower than the limit of 370Bqkg{sup -1} set in the Organization for Economic Cooperation and Development [OECD, 1979. Exposure to radiation from the natural radioactivity in building materials. OECD, Paris] report which is equivalent to a {gamma}-dose of 1.5mSvyr{sup -1}. Except for the gravel from Logbadjeck, all the materials examined are acceptable for use as building materials as defined by the OECD criterion.