Elemental marking of arthropod pests in agricultural systems: single and multigenerational marking

Science.gov (United States)

Jane Leslie Hayes

1991-01-01

Use of elemental markers to study movement of arthropod pests of field crops is reviewed. Trace elements, rubidium (Rb) and cesium (Cs), have provided a nondisruptive method of marking natural adult populations via developmental stage consumption of treated host plants. Multigenerational marking occurs with the transfer of elemental markers from marked adults to...

The hazard to man of accidental releases of tritium

International Nuclear Information System (INIS)

Brearley, I.R.

1985-03-01

Some aspects of the atmospheric dispersion of tritium are discussed, followed by consideration of the dosimetric pathways. In order to assess the significance of a tritium release the doses from various pathways are estimated and compared with the doses estimated from a similar release of iodine-131. The major hazard from tritium is the ingestion of contaminated food products. For similar releases of tritium and I 131 the ingestion hazard can be comparable if the release occurs near and before the end of the harvest season. However, in the tritium release case the agricultural season influences the consequences markedly and, at other times during the year, the ingestion hazard from tritium may be approximately 20 times less. The dose from inhalation of tritium is sensitive to its chemical form and for similar releases of tritiated water and tritium gas then the dose from tritiated water is approximately 10 4 greater than the dose from tritium gas. For similar releases of tritiated water and iodine-131 then a comparison of the inhalation shows that the dose from the iodine is approximately 300 times greater. (author)

Elevation uncertainty in coastal inundation hazard assessments

Science.gov (United States)

Gesch, Dean B.; Cheval, Sorin

2012-01-01

Coastal inundation has been identified as an important natural hazard that affects densely populated and built-up areas (Subcommittee on Disaster Reduction, 2008). Inundation, or coastal flooding, can result from various physical processes, including storm surges, tsunamis, intense precipitation events, and extreme high tides. Such events cause quickly rising water levels. When rapidly rising water levels overwhelm flood defenses, especially in heavily populated areas, the potential of the hazard is realized and a natural disaster results. Two noteworthy recent examples of such natural disasters resulting from coastal inundation are the Hurricane Katrina storm surge in 2005 along the Gulf of Mexico coast in the United States, and the tsunami in northern Japan in 2011. Longer term, slowly varying processes such as land subsidence (Committee on Floodplain Mapping Technologies, 2007) and sea-level rise also can result in coastal inundation, although such conditions do not have the rapid water level rise associated with other flooding events. Geospatial data are a critical resource for conducting assessments of the potential impacts of coastal inundation, and geospatial representations of the topography in the form of elevation measurements are a primary source of information for identifying the natural and human components of the landscape that are at risk. Recently, the quantity and quality of elevation data available for the coastal zone have increased markedly, and this availability facilitates more detailed and comprehensive hazard impact assessments.

Lujan Mark-4

Energy Technology Data Exchange (ETDEWEB)

Mocko, Michael Jeffrey [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Zavorka, Lukas [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Koehler, Paul E. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-11-13

This is a review of Mark-IV target neutronics design. It involved the major redesign of the upper tier, offering harder neutron spectra for upper-tier FPs; a redesign of the high-resolution (HR) moderator; and a preservation of the rest of Mark-III features.

Minimal Marking: A Success Story

Science.gov (United States)

McNeilly, Anne

2014-01-01

The minimal-marking project conducted in Ryerson's School of Journalism throughout 2012 and early 2013 resulted in significantly higher grammar scores in two first-year classes of minimally marked university students when compared to two traditionally marked classes. The "minimal-marking" concept (Haswell, 1983), which requires…

Radioactive waste management plan during the TRIGA Mark II and III decommissioning

International Nuclear Information System (INIS)

Jung, K.J.; Park, S.K.; Geong, G.H.; Lee, K.W.; Chung, U.S.; Paik, S.T.

2001-01-01

The decontamination and decommissioning (D and D) project of TRIGA Mark-I and Mark-II (KRR 1 and 2) was started in January 1997 and will be completed by December 2002. In the first year of the project, work was performed in preparation of the decommissioning plan, start of the environmental impact assessment and setup licensing procedure and documentation for the project with cooperation of the Korea Institute of Nuclear Safety (KINS). In the second year, Hyundai Engineering Company (HEC) with British Nuclear Fuels pie (BNFL) as technical assisting partner was designated as the contractor to do design and licensing documentation for the D and D of both reactors. After pre-design, a hazard and operability (HAZOP) study checked each step of the work. At the end of 1998, the decommissioning plan documentation including environmental impact assessment report was finished and submitted to the Ministry of Science and Technology (MOST) for licensing. It is expected to be issued by the end of September 1999. Practical work will then be started around the end of 1999. The safe treatment and management of the radioactive waste arising from the D and D activities is of utmost importance for successful completion of the practical dismantling work. This paper summarizes general aspects of radioactive waste treatment and management plan for the TRIGA Mark-I and II decommissioning work. (author)

Mark Stock | NREL

Science.gov (United States)

Stock Mark Stock Scientific Visualization Specialist Mark.Stock@nrel.gov | 303-275-4174 Dr. Stock , virtual reality, parallel computing, and manipulation of large spatial data sets. As an artist, he creates . Stock built the SUNLIGHT artwork that is installed on the Webb Building in downtown Denver. In addition

Transportation of Hazardous Materials Emergency Preparedness Hazards Assessment

Energy Technology Data Exchange (ETDEWEB)

Blanchard, A.

2000-02-28

This report documents the Emergency Preparedness Hazards Assessment (EPHA) for the Transportation of Hazardous Materials (THM) at the Department of Energy (DOE) Savannah River Site (SRS). This hazards assessment is intended to identify and analyze those transportation hazards significant enough to warrant consideration in the SRS Emergency Management Program.

Transportation of Hazardous Materials Emergency Preparedness Hazards Assessment

International Nuclear Information System (INIS)

Blanchard, A.

2000-01-01

This report documents the Emergency Preparedness Hazards Assessment (EPHA) for the Transportation of Hazardous Materials (THM) at the Department of Energy (DOE) Savannah River Site (SRS). This hazards assessment is intended to identify and analyze those transportation hazards significant enough to warrant consideration in the SRS Emergency Management Program

Transportation of hazardous materials emergency preparedness hazards assessment

International Nuclear Information System (INIS)

Blanchard, A.

2000-01-01

This report documents the Emergency Preparedness Hazards Assessment (EPHA) for the Transportation of Hazardous Materials (THM) at the Department of Energy (DOE) Savannah River Site (SRS). This hazards assessment is intended to identify and analyze those transportation hazards significant enough to warrant consideration in the SRS Emergency Management Program

Hazard function theory for nonstationary natural hazards

Science.gov (United States)

Read, L.; Vogel, R. M.

2015-12-01

Studies from the natural hazards literature indicate that many natural processes, including wind speeds, landslides, wildfires, precipitation, streamflow and earthquakes, show evidence of nonstationary behavior such as trends in magnitudes through time. Traditional probabilistic analysis of natural hazards based on partial duration series (PDS) generally assumes stationarity in the magnitudes and arrivals of events, i.e. that the probability of exceedance is constant through time. Given evidence of trends and the consequent expected growth in devastating impacts from natural hazards across the world, new methods are needed to characterize their probabilistic behavior. The field of hazard function analysis (HFA) is ideally suited to this problem because its primary goal is to describe changes in the exceedance probability of an event over time. HFA is widely used in medicine, manufacturing, actuarial statistics, reliability engineering, economics, and elsewhere. HFA provides a rich theory to relate the natural hazard event series (x) with its failure time series (t), enabling computation of corresponding average return periods and reliabilities associated with nonstationary event series. This work investigates the suitability of HFA to characterize nonstationary natural hazards whose PDS magnitudes are assumed to follow the widely applied Poisson-GP model. We derive a 2-parameter Generalized Pareto hazard model and demonstrate how metrics such as reliability and average return period are impacted by nonstationarity and discuss the implications for planning and design. Our theoretical analysis linking hazard event series x, with corresponding failure time series t, should have application to a wide class of natural hazards.

Hazard function theory for nonstationary natural hazards

Science.gov (United States)

Read, Laura K.; Vogel, Richard M.

2016-04-01

Impact from natural hazards is a shared global problem that causes tremendous loss of life and property, economic cost, and damage to the environment. Increasingly, many natural processes show evidence of nonstationary behavior including wind speeds, landslides, wildfires, precipitation, streamflow, sea levels, and earthquakes. Traditional probabilistic analysis of natural hazards based on peaks over threshold (POT) generally assumes stationarity in the magnitudes and arrivals of events, i.e., that the probability of exceedance of some critical event is constant through time. Given increasing evidence of trends in natural hazards, new methods are needed to characterize their probabilistic behavior. The well-developed field of hazard function analysis (HFA) is ideally suited to this problem because its primary goal is to describe changes in the exceedance probability of an event over time. HFA is widely used in medicine, manufacturing, actuarial statistics, reliability engineering, economics, and elsewhere. HFA provides a rich theory to relate the natural hazard event series (X) with its failure time series (T), enabling computation of corresponding average return periods, risk, and reliabilities associated with nonstationary event series. This work investigates the suitability of HFA to characterize nonstationary natural hazards whose POT magnitudes are assumed to follow the widely applied generalized Pareto model. We derive the hazard function for this case and demonstrate how metrics such as reliability and average return period are impacted by nonstationarity and discuss the implications for planning and design. Our theoretical analysis linking hazard random variable X with corresponding failure time series T should have application to a wide class of natural hazards with opportunities for future extensions.

Hazards assessment for the Hazardous Waste Storage Facility

International Nuclear Information System (INIS)

Knudsen, J.K.; Calley, M.B.

1994-04-01

This report documents the hazards assessment for the Hazardous Waste Storage Facility (HWSF) located at the Idaho National Engineering Laboratory. The hazards assessment was performed to ensure that this facility complies with DOE and company requirements pertaining to emergency planning and preparedness for operational emergencies. The hazards assessment identifies and analyzes hazards that are significant enough to warrant consideration in a facility's operational emergency management program. The area surrounding HWSF, the buildings and structures at HWSF, and the processes used at HWSF are described in this report. All nonradiological hazardous materials at the HWSF were identified (radiological hazardous materials are not stored at HWSF) and screened against threshold quantities according to DOE Order 5500.3A guidance. Two of the identified hazardous materials exceeded their specified threshold quantity. This report discusses the potential release scenarios and consequences associated with an accidental release for each of the two identified hazardous materials, lead and mercury. Emergency considerations, such as emergency planning zones, emergency classes, protective actions, and emergency action levels, are also discussed based on the analysis of potential consequences. Evaluation of the potential consequences indicated that the highest emergency class for operational emergencies at the HWSF would be a Site Area Emergency

Hazard interactions and interaction networks (cascades) within multi-hazard methodologies

Science.gov (United States)

Gill, Joel C.; Malamud, Bruce D.

2016-08-01

This paper combines research and commentary to reinforce the importance of integrating hazard interactions and interaction networks (cascades) into multi-hazard methodologies. We present a synthesis of the differences between multi-layer single-hazard approaches and multi-hazard approaches that integrate such interactions. This synthesis suggests that ignoring interactions between important environmental and anthropogenic processes could distort management priorities, increase vulnerability to other spatially relevant hazards or underestimate disaster risk. In this paper we proceed to present an enhanced multi-hazard framework through the following steps: (i) description and definition of three groups (natural hazards, anthropogenic processes and technological hazards/disasters) as relevant components of a multi-hazard environment, (ii) outlining of three types of interaction relationship (triggering, increased probability, and catalysis/impedance), and (iii) assessment of the importance of networks of interactions (cascades) through case study examples (based on the literature, field observations and semi-structured interviews). We further propose two visualisation frameworks to represent these networks of interactions: hazard interaction matrices and hazard/process flow diagrams. Our approach reinforces the importance of integrating interactions between different aspects of the Earth system, together with human activity, into enhanced multi-hazard methodologies. Multi-hazard approaches support the holistic assessment of hazard potential and consequently disaster risk. We conclude by describing three ways by which understanding networks of interactions contributes to the theoretical and practical understanding of hazards, disaster risk reduction and Earth system management. Understanding interactions and interaction networks helps us to better (i) model the observed reality of disaster events, (ii) constrain potential changes in physical and social vulnerability

Road Nail: Experimental Solar Powered Intelligent Road Marking System

Science.gov (United States)

Samardžija, Dragan; Teslić, Nikola; Todorović, Branislav M.; Kovač, Erne; Isailović, Đorđe; Miladinović, Bojan

2012-03-01

Driving in low visibility conditions (night time, fog or heavy precipitation) is particularly challenging task with an increased probability of traffic accidents and possible injuries. Road Nail is a solar powered intelligent road marking system of wirelessly networked signaling devices that improve driver safety in low visibility conditions along hazardous roadways. Nails or signaling devices are autonomous nodes with capability to accumulate energy, exchange wireless messages, detect approaching vehicles and emit signalization light. We have built an experimental test-bed that consists of 20 nodes and a cellular gateway. Implementation details of the above system, including extensive measurements and performance evaluations in realistic field deployments are presented. A novel distributed network topology discovery scheme is proposed which integrates both sensor and wireless communication aspects, where nodes act autonomously. Finally, integration of the Road Nail system with the cellular network and the Internet is described.

46 CFR 185.602 - Hull markings.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Hull markings. 185.602 Section 185.602 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS (UNDER 100 GROSS TONS) OPERATIONS Markings Required § 185.602 Hull markings. (a) Each vessel must be marked as required by part 67...

Mark Kostabi soovib muuta inimesi õnnelikumaks / Kalev Mark Kostabi

Index Scriptorium Estoniae

Kostabi, Kalev Mark, 1960-

2008-01-01

Kalev Mark Kostabi oma sisekujunduslikest eelistustest, ameeriklaste ja itaallaste kodude sisekujunduse erinevustest, kunstist kui ruumikujunduse ühest osast, oma New Yorgi ja Rooma korterite kujundusest

27 CFR 28.193 - Export marks.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Export marks. 28.193... Drawback Filing of Notice and Removal § 28.193 Export marks. In addition to the marks and brands required... chapter, the exporter shall mark the word “Export” on the Government side of each case or Government head...

27 CFR 28.103 - Export marks.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Export marks. 28.103... Manufacturing Bonded Warehouse § 28.103 Export marks. (a) General. In addition to the marks and brands required... provisions of part 19 of this chapter, the proprietor shall mark the word “Export” on the Government side of...

27 CFR 28.144 - Export marks.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Export marks. 28.144... § 28.144 Export marks. (a) General Requirement. In addition to the marks and brands required to be... brewer shall mark the word “Export” on each container or case of beer, or the words “Beer concentrate for...

27 CFR 28.154 - Export marks.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Export marks. 28.154..., for Exportation or Transfer to a Foreign-Trade Zone § 28.154 Export marks. In addition to the marks... provisions of part 19 of this chapter, the proprietor shall mark the word “Export” on the Government side of...

1L Mark-IV Target Design Review

Energy Technology Data Exchange (ETDEWEB)

Koehler, Paul E. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-11-16

This presentation includes General Design Considerations; Current (Mark-III) Lower Tier; Mark-III Upper Tier; Performance Metrics; General Improvements for Material Science; General Improvements for Nuclear Science; Improving FOM for Nuclear Science; General Design Considerations Summary; Design Optimization Studies; Expected Mark-IV Performance: Material Science; Expected Mark-IV Performance: Nuclear Science (Disk); Mark IV Enables Much Wider Range of Nuclear-Science FOM Gains than Mark III; Mark-IV Performance Summary; Rod or Disk? Center or Real FOV?; and Project Cost and Schedule.

High contrast laser marking of alumina

International Nuclear Information System (INIS)

Penide, J.; Quintero, F.; Riveiro, A.; Fernández, A.; Val, J. del; Comesaña, R.; Lusquiños, F.; Pou, J.

2015-01-01

Highlights: • Laser marking of alumina using near infrared (NIR) lasers was experimentally analyzed. • Color change produced by NIR lasers is due to thermally induced oxygen vacancies. • Laser marking results obtained using NIR lasers and green laser are compared. • High contrast marks on alumina were achieved. - Abstract: Alumina serves as raw material for a broad range of advanced ceramic products. These elements should usually be identified by some characters or symbols printed directly on them. In this sense, laser marking is an efficient, reliable and widely implemented process in industry. However, laser marking of alumina still leads to poor results since the process is not able to produce a dark mark, yielding bad contrast. In this paper, we present an experimental study on the process of marking alumina by three different lasers working in two wavelengths: 1064 nm (Near-infrared) and 532 nm (visible, green radiation). A colorimetric analysis has been carried out in order to compare the resulting marks and its contrast. The most suitable laser operating conditions were also defined and are reported here. Moreover, the physical process of marking by NIR lasers is discussed in detail. Field Emission Scanning Electron Microscopy, High Resolution Transmission Electron Microscopy and X-ray Photoelectron Spectroscopy were also employed to analyze the results. Finally, we propose an explanation for the differences of the coloration induced under different atmospheres and laser parameters. We concluded that the atmosphere is the key parameter, being the inert one the best choice to produce the darkest marks

Changing Context of Trade Mark Protection in India: A Review of the Trade Marks Act, 1999

OpenAIRE

Pathak, Akhileshwar

2004-01-01

With liberalisation and globalisation of the Indian economy, it has become possible for anyone to get into production and services in most of the sectors. This has led to rampant misuse and appropriation of trade marks. In an insulated economy, with monopoly markets, law protecting trade marks had a limited role. In the changed context, however, trade mark law will be a field of much interest for academics and practitioners. Towards this, the paper explores the formation of trade mark law in ...

Hazards and hazard combinations relevant for the safety of nuclear power plants

Science.gov (United States)

Decker, Kurt; Brinkman, Hans; Raimond, Emmanuel

2017-04-01

The potential of the contemporaneous impact of different, yet causally related, hazardous events and event cascades on nuclear power plants is a major contributor to the overall risk of nuclear installations. In the aftermath of the Fukushima accident, which was caused by a combination of severe ground shaking by an earthquake, an earthquake-triggered tsunami and the disruption of the plants from the electrical grid by a seismically induced landslide, hazard combinations and hazard cascades moved into the focus of nuclear safety research. We therefore developed an exhaustive list of external hazards and hazard combinations which pose potential threats to nuclear installations in the framework of the European project ASAMPSAE (Advanced Safety Assessment: Extended PSA). The project gathers 31 partners from Europe, North Amerika and Japan. The list comprises of exhaustive lists of natural hazards, external man-made hazards, and a cross-correlation matrix of these hazards. The hazard list is regarded comprehensive by including all types of hazards that were previously cited in documents by IAEA, the Western European Nuclear Regulators Association (WENRA), and others. 73 natural hazards and 24 man-made external hazards are included. Natural hazards are grouped into seismotectonic hazards, flooding and hydrological hazards, extreme values of meteorological phenomena, rare meteorological phenomena, biological hazards / infestation, geological hazards, and forest fire / wild fire. The list of external man-made hazards includes industry accidents, military accidents, transportation accidents, pipeline accidents and other man-made external events. The large number of different hazards results in the extremely large number of 5.151 theoretically possible hazard combinations (not considering hazard cascades). In principle all of these combinations are possible to occur by random coincidence except for 82 hazard combinations that - depending on the time scale - are mutually

Hazardous Waste

Science.gov (United States)

... chemicals can still harm human health and the environment. When you throw these substances away, they become hazardous waste. Some hazardous wastes come from products in our homes. Our garbage can include such hazardous wastes as old batteries, bug spray cans and paint thinner. U.S. residents ...

Experimental applications for the MARK-1 and MARK-1A pulsed ionizing radiation detection systems. Volume 3

International Nuclear Information System (INIS)

Harker, Y.D.; Lawrence, R.S.; Yoon, W.Y.; Lones, J.L.

1993-12-01

This report is the third volume in a three volume set describing the MARK series of pulsed ionizing radiation detection systems. This volume describes the MARK-1A detection system, compares it with the MARK-1 system, and describes the experimental testing of the detection systems. Volume 1 of this set presents the technical specifications for the MARK-1 detection system. Volume 2 is an operations manual specifically for the MARK-1 system, but it generally applies to the MARK-1A system as well. These detection systems operate remotely and detect photon radiation from a single or a multiple pulsed source. They contain multiple detector (eight in the MARK-1 and ten in the MARK-1A) for determination of does and incident photon effective energy. The multiple detector arrangement, having different detector sizes and shield thicknesses, provides the capability of determining the effective photon energy of the radiation spectrum. Dose measurements using these units are consistent with TLD measurements. The detection range is from 3 nanorads to 90 microrads per source burst; the response is linear over that range. Three units were built and are ready for field deployment

Augmented marked graphs

CERN Document Server

Cheung, King Sing

2014-01-01

Petri nets are a formal and theoretically rich model for the modelling and analysis of systems. A subclass of Petri nets, augmented marked graphs possess a structure that is especially desirable for the modelling and analysis of systems with concurrent processes and shared resources.This monograph consists of three parts: Part I provides the conceptual background for readers who have no prior knowledge on Petri nets; Part II elaborates the theory of augmented marked graphs; finally, Part III discusses the application to system integration. The book is suitable as a first self-contained volume

Court presentation of bite mark evidence.

Science.gov (United States)

Drinnan, A J; Melton, M J

1985-12-01

The uniqueness of an individual's bite mark is generally accepted. The use of bite mark analysis to identify or exclude those suspected of crimes is now a well established activity in forensic dentistry. Although the techniques for evaluating bite mark evidence are extremely sophisticated, it is important that the courtroom presentation of such evidence should be as simple as possible and be directed towards those who must judge it. Dentists likely to be involved in the courtroom presentation of bite mark evidence should: be certain that their local law enforcement personnel are frequently updated on the techniques to be used for producing the optimum evidence needed to evaluate bite marks; become acquainted with the current techniques of evaluating bite mark evidence and understand their difficulties and pitfalls; meet with the lawyers (prosecution or defence) before a courtroom appearance, briefing them on the significance of the particular findings; prepare clear and easily understandable visual aids to present to the court the techniques used in the analysis and the bases for the conclusion reached; and offer conclusions derived from the bite mark investigation.

Hazard perception in traffic. [previously knows as: Hazard perception.

NARCIS (Netherlands)

2008-01-01

Hazard perception is an essential part of the driving task. There are clear indications that insufficient skills in perceiving hazards play an important role in the occurrence of crashes, especially those involving novice drivers. Proper hazard perception not only consists of scanning and perceiving

Nuclear particle track-etched anti-bogus mark

International Nuclear Information System (INIS)

He Xiangming; Yan Yushun; Zhang Quanrong

2003-01-01

Nuclear particle track-etched anti-bogus mark is a new type of forgery-proof product after engraving gravure printing, thermocolour, fluorescence, laser hologram and metal concealed anti-bogus mark. The mark is manufactured by intricate high technology and the state strictly controlled sensitive nuclear facilities to ensure the mark not to be copied. The pattern of the mark is specially characterized by permeability of liquid to be discriminated from forgery. The genuine mark can be distinguished from sham one by transparent liquid (e.g. water), colorful pen and chemical reagent. The mark has passed the official examination of health safety. It is no danger of nuclear irradiation. (author)

High efficiency metal marking with CO2 laser and glass marking with excimer laser

DEFF Research Database (Denmark)

Bastue, Jens; Olsen, Flemmming Ove

1997-01-01

with a thoroughly tested ray-tracing model is presented and compared with experimental results. Special emphasis is put on two different applications namely marking in metal with TEA-CO2 laser and marking in glass with excimer laser. The results are evaluated on the basis of the achievable energy enhancement......Today, mask based laser materials processing and especially marking is widely used. However, the energy efficiency in such processes is very low [1].This paper gives a review of the results, that may be obtained using the energy enhancing technique [1]. Results of simulations performed...

Identification of Potential Hazard using Hazard Identification and Risk Assessment

Science.gov (United States)

Sari, R. M.; Syahputri, K.; Rizkya, I.; Siregar, I.

2017-03-01

This research was conducted in the paper production’s company. These Paper products will be used as a cigarette paper. Along in the production’s process, Company provides the machines and equipment that operated by workers. During the operations, all workers may potentially injured. It known as a potential hazard. Hazard identification and risk assessment is one part of a safety and health program in the stage of risk management. This is very important as part of efforts to prevent occupational injuries and diseases resulting from work. This research is experiencing a problem that is not the identification of potential hazards and risks that would be faced by workers during the running production process. The purpose of this study was to identify the potential hazards by using hazard identification and risk assessment methods. Risk assessment is done using severity criteria and the probability of an accident. According to the research there are 23 potential hazard that occurs with varying severity and probability. Then made the determination Risk Assessment Code (RAC) for each potential hazard, and gained 3 extreme risks, 10 high risks, 6 medium risks and 3 low risks. We have successfully identified potential hazard using RAC.

[Diagnostic imaging and radiation hazards].

Science.gov (United States)

Claudon, Michel; Guillaume, Luc

2015-01-01

For the last 20 years, the exposure of the population to medical radiation has been increased by 600%, mainly due to the extension of new imaging modalities such as CT or interventional radiology. The risk for radio-induced hazards is especially marked for children, because of the high sensivity of tissues to radiation especially during the first decade of the life. Two main ways allow to better control and reduce the mean effective dose per patient in diagnostic imaging: the introduction of recent technical improvement (i.e. low dose CT scans using iterative reconstruction algorithms, low dose technique for pediatric spine), and the substitution to non-radiating techniques such as ultrasound and MRI. The French National institute of Radioprotection and Nuclear Safety periodically publishes dose reference levels for conventional films and CT examinations, for both adults and pediatric patients. A close relationship between clinicians and radiologists remains essential for a better appreciation of the risk/benefit ratio of each individual examination using X-Rays.

46 CFR 160.176-23 - Marking.

Science.gov (United States)

2010-10-01

... of the vessel. (2) The type of vessel. (3) Specific purpose or limitation approved by the Coast Guard...: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Inflatable Lifejackets § 160.176-23 Marking. (a) General. Each inflatable lifejacket must be marked with the information required by this section. Each marking must be...

On-road Bicycle Pavement Markings

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — A mile by mile breakdown of the on-street bicycle pavement markings installed within the City of Pittsburgh. These include bike lanes, shared lane markings...

Marks of Metal Copenhell

DEFF Research Database (Denmark)

2015-01-01

Planchebaseret udendørs udstilling på musikfestivalen Copenhell 18-20/6 2015. En mindre udgave af udstillingen Marks of Metal - Logodesign og visualitet i heavy metal. Udarbejdet i samarbejde med Mediemuseet.......Planchebaseret udendørs udstilling på musikfestivalen Copenhell 18-20/6 2015. En mindre udgave af udstillingen Marks of Metal - Logodesign og visualitet i heavy metal. Udarbejdet i samarbejde med Mediemuseet....

Circulatory Markings at Double-Lane Traffic Roundabout.

NARCIS (Netherlands)

Bie, Jing; Lo, Hong K.; Wong, S.C.

2008-01-01

This paper compares two types of circulatory markings at a double-lane traffic roundabout: the concentric marking scheme and the Alberta marking scheme. The effects of these two marking schemes on drivers' lane choice behavior, delay, and safety, are compared based on data collected from before and

7 CFR 160.32 - Marking containers.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Marking containers. 160.32 Section 160.32 Agriculture... STANDARDS FOR NAVAL STORES Analysis, Inspection, and Grading on Request § 160.32 Marking containers. The interested person shall provide any labor necessary for marking the containers, after the contents have been...

46 CFR 122.602 - Hull markings.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Hull markings. 122.602 Section 122.602 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS CARRYING MORE THAN 150....602 Hull markings. (a) Each vessel must be marked as required by part 67, subpart I, of this chapter...

Stretch Marks

Science.gov (United States)

... completely without the help of a dermatologist or plastic surgeon. These doctors may use one of many types of treatments — from actual surgery to techniques like microdermabrasion and laser treatment — to reduce the appearance of stretch marks. These techniques are ...

High contrast laser marking of alumina

Science.gov (United States)

Penide, J.; Quintero, F.; Riveiro, A.; Fernández, A.; del Val, J.; Comesaña, R.; Lusquiños, F.; Pou, J.

2015-05-01

Alumina serves as raw material for a broad range of advanced ceramic products. These elements should usually be identified by some characters or symbols printed directly on them. In this sense, laser marking is an efficient, reliable and widely implemented process in industry. However, laser marking of alumina still leads to poor results since the process is not able to produce a dark mark, yielding bad contrast. In this paper, we present an experimental study on the process of marking alumina by three different lasers working in two wavelengths: 1064 nm (Near-infrared) and 532 nm (visible, green radiation). A colorimetric analysis has been carried out in order to compare the resulting marks and its contrast. The most suitable laser operating conditions were also defined and are reported here. Moreover, the physical process of marking by NIR lasers is discussed in detail. Field Emission Scanning Electron Microscopy, High Resolution Transmission Electron Microscopy and X-ray Photoelectron Spectroscopy were also employed to analyze the results. Finally, we propose an explanation for the differences of the coloration induced under different atmospheres and laser parameters. We concluded that the atmosphere is the key parameter, being the inert one the best choice to produce the darkest marks.

27 CFR 28.123 - Export marks.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Export marks. 28.123..., or Transportation to a Manufacturing Bonded Warehouse § 28.123 Export marks. (a) General. In addition... filled under the provisions of part 24 of this chapter, the proprietor shall mark the word “Export” on...

The hazard communication of fragrance allergens must be improved.

Science.gov (United States)

Klaschka, Ursula

2013-07-01

Contact allergy is a global health problem that could be alleviated considerably if the general public could reduce contact to sensitizers. Efficient hazard communication would be a valuable instrument to achieve this. What do current regulations concerning fragrance sensitizers in cosmetic products in Europe contribute? For example, there are bans and restrictions according to the Cosmetic Regulation, there is the "26 allergens rule" that requires that the names of some allergenic fragrance ingredients are listed on the containers, there is labeling and classification of hazardous products according to Regulation 1272/2008, and there is the regulation concerning the registration, evaluation, authorization and restriction of chemicals (REACH). Do these regulations increase consumer protection by suitable hazard communication instruments? Four main problems were identified. First, according to the 26 allergens rule, consumers carry a very large part of the responsibility for risk reduction management. They need to be capable and motivated to recognize the names of strong allergens listed in the ingredient list and decide for themselves whether they want to run the risk or not, provided that they are aware of their responsibility. Second, cosmetic products do not need to be classified and labeled like other consumer goods, according to the European Commission Regulation 1272/2008, if they contain hazardous substances. Third, some pictograms for hazardous substances, for example, the exclamation mark for sensitizers, are not well understood by the majority of the general public. Fourth, very often, the design of cosmetic containers implies health and well being, even if the respective products contain sensitizers or other hazardous substances. Against this background, the following improvements are proposed: 1) the 26 allergens rule needs revision, 2) the exception for cosmetic products from labeling and classification should be abolished, 3) a new self

27 CFR 28.223 - Export marks.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Export marks. 28.223... Export marks. In addition to the marks and brands required to be placed on kegs, barrels, cases, crates... “Export” on each container or case before removal for export, for use on vessels or aircraft, or for...

46 CFR 78.50-5 - Hull markings.

Science.gov (United States)

2010-10-01

... 46 Shipping 3 2010-10-01 2010-10-01 false Hull markings. 78.50-5 Section 78.50-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) PASSENGER VESSELS OPERATIONS Markings on Vessels § 78.50-5 Hull markings. Vessels shall be marked as required by parts 67 and 69 of this chapter. [CGD 72...

46 CFR 196.40-5 - Hull markings.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Hull markings. 196.40-5 Section 196.40-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OCEANOGRAPHIC RESEARCH VESSELS OPERATIONS Markings on Vessels § 196.40-5 Hull markings. Vessels shall be marked as required by parts 67 and 69 of this chapter...

46 CFR 97.40-5 - Hull markings.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Hull markings. 97.40-5 Section 97.40-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CARGO AND MISCELLANEOUS VESSELS OPERATIONS Markings on Vessels § 97.40-5 Hull markings. Vessels shall be marked as required by parts 67 and 69 of this...

Working towards a clearer and more helpful hazard map: investigating the influence of hazard map design on hazard communication

Science.gov (United States)

Thompson, M. A.; Lindsay, J. M.; Gaillard, J.

2015-12-01

Globally, geological hazards are communicated using maps. In traditional hazard mapping practice, scientists analyse data about a hazard, and then display the results on a map for stakeholder and public use. However, this one-way, top-down approach to hazard communication is not necessarily effective or reliable. The messages which people take away will be dependent on the way in which they read, interpret, and understand the map, a facet of hazard communication which has been relatively unexplored. Decades of cartographic studies suggest that variables in the visual representation of data on maps, such as colour and symbology, can have a powerful effect on how people understand map content. In practice, however, there is little guidance or consistency in how hazard information is expressed and represented on maps. Accordingly, decisions are often made based on subjective preference, rather than research-backed principles. Here we present the results of a study in which we explore how hazard map design features can influence hazard map interpretation, and we propose a number of considerations for hazard map design. A series of hazard maps were generated, with each one showing the same probabilistic volcanic ashfall dataset, but using different verbal and visual variables (e.g., different colour schemes, data classifications, probabilistic formats). Following a short pilot study, these maps were used in an online survey of 110 stakeholders and scientists in New Zealand. Participants answered 30 open-ended and multiple choice questions about ashfall hazard based on the different maps. Results suggest that hazard map design can have a significant influence on the messages readers take away. For example, diverging colour schemes were associated with concepts of "risk" and decision-making more than sequential schemes, and participants made more precise estimates of hazard with isarithmic data classifications compared to binned or gradational shading. Based on such

Hazard Analysis Database Report

Energy Technology Data Exchange (ETDEWEB)

GAULT, G.W.

1999-10-13

The Hazard Analysis Database was developed in conjunction with the hazard analysis activities conducted in accordance with DOE-STD-3009-94, Preparation Guide for US Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports, for the Tank Waste Remediation System (TWRS) Final Safety Analysis Report (FSAR). The FSAR is part of the approved TWRS Authorization Basis (AB). This document describes, identifies, and defines the contents and structure of the TWRS FSAR Hazard Analysis Database and documents the configuration control changes made to the database. The TWRS Hazard Analysis Database contains the collection of information generated during the initial hazard evaluations and the subsequent hazard and accident analysis activities. The database supports the preparation of Chapters 3,4, and 5 of the TWRS FSAR and the USQ process and consists of two major, interrelated data sets: (1) Hazard Evaluation Database--Data from the results of the hazard evaluations; and (2) Hazard Topography Database--Data from the system familiarization and hazard identification.

Handbook of hazardous waste management

International Nuclear Information System (INIS)

Metry, A.A.

1980-01-01

The contents of this work are arranged so as to give the reader a detailed understanding of the elements of hazardous waste management. Generalized management concepts are covered in Chapters 1 through 5 which are entitled: Introduction, Regulations Affecting Hazardous Waste Management, Comprehensive Hazardous Waste Management, Control of Hazardous Waste Transportation, and Emergency Hazardous Waste Management. Chapters 6 through 11 deal with treatment concepts and are entitled: General Considerations for Hazardous Waste Management Facilities, Physical Treatment of Hazardous Wastes, Chemical Treatment of Hazardous Wastes, Biological Treatment of Hazardous Wastes, Incineration of Hazardous Wastes, and Hazardous Waste Management of Selected Industries. Chapters 12 through 15 are devoted to ultimate disposal concepts and are entitled: Land Disposal Facilities, Ocean Dumping of Hazardous Wastes, Disposal of Extremely Hazardous Wastes, and Generalized Criteria for Hazardous Waste Management Facilities

Mark II magnetic detector for SPEAR

International Nuclear Information System (INIS)

Larsen, R.R.

1975-01-01

The Mark II Detector, presently in the design stage, is a SLAC/LBL detector project to replace the Mark I now in operation at SPEAR. While similar in concept to the Mark I it will have improved momentum resolution, shower detection, solid angle coverage for both triggering and tracking and a magnet design providing easier access to those particles transmitted through the aluminum coil

Mark Napier / Mark Napier ; interv. Tilman Baumgärtel

Index Scriptorium Estoniae

Napier, Mark

2006-01-01

Ameerika kunstnikust Mark Napierist (sünd. 1961) ja tema loomingust, 2001. a. tehtud meiliintervjuu kunstnikuga. Võrguteosest "The Digital Landfill" (1998), koos Andy Deckiga loodud tööst "GrafficJam" (1999), töödest "Shredder" (1998), "Feed", "Riot", "P-Soup" (2000), võrgukunstist ja muust

Egyptian Environmental Activities and Regulations for Management of Hazardous Substances and Hazardous Wastes

International Nuclear Information System (INIS)

El Zarka, M.

1999-01-01

A substantial use of hazardous substances is essential to meet the social and economic goals of the community in Egypt. Agrochemicals are being used extensively to increase crop yield. The outdated agrochemicals and their empty containers represent a serious environmental problem. Industrial development in different sectors in Egypt obligates handling of huge amounts of hazardous substances and hazardous wastes. The inappropriate handling of such hazardous substances creates several health and environmental problems. Egypt faces many challenges to control safe handling of such substances and wastes. Several regulations are governing handling of hazardous substances in Egypt. The unified Environmental Law 4 for the year 1994 includes a full chapter on the Management of Hazardous Substances and Hazardous Wastes. National and international activities have been taken to manage hazardous substances and hazardous wastes in an environmental sound manner

Hazard classification methodology

International Nuclear Information System (INIS)

Brereton, S.J.

1996-01-01

This document outlines the hazard classification methodology used to determine the hazard classification of the NIF LTAB, OAB, and the support facilities on the basis of radionuclides and chemicals. The hazard classification determines the safety analysis requirements for a facility

Responses of female rock lizards to multiple scent marks of males: effects of male age, male density and scent over-marking.

Science.gov (United States)

Martín, José; López, Pilar

2013-03-01

Scent-marked substrates may inform conspecifics on the characteristics of territorial males. Scent-marks of male Carpetan rock lizards (Iberolacerta cyreni) affect space use of females, which by selecting an area may increase the probability of mating with the male that has scent-marked that area. However, males do not hold exclusive territories, and scent-marks of different individual males are often together. This may provide complex information from multiple sources on the social structure. Here, we examined female preference in response to scent marks of various males and combinations in a laboratory experiment. Females preferred areas scent-marked by territorial old males against those scent-marked by young satellite-sneaker males. This reflected the known preference of females for mating with old males. In a second experiment, females preferred areas scent-marked by two males to areas of similar size marked by a single male. This may increase the probability of obtaining multiple copulations with different males, which may favour sperm competition and cryptic female choice, or may be a way to avoid infertile males. Finally, when we experimentally over-marked the scent-marks of an old male with scent-marks of a young male, females did not avoid, nor prefer, the over-marked area, suggesting that the quality of the old male may override the presence of a satellite male. We suggest that, irrespective of the causes underlying why a female selects a scent-marked area, this strategy may affect her reproductive success, which may have the same evolutionary consequences that "direct" mate choice decisions of other animals. Copyright © 2013 Elsevier B.V. All rights reserved.

Percentage Retail Mark-Ups

OpenAIRE

Thomas von Ungern-Sternberg

1999-01-01

A common assumption in the literature on the double marginalization problem is that the retailer can set his mark-up only in the second stage of the game after the producer has moved. To the extent that the sequence of moves is designed to reflect the relative bargaining power of the two parties it is just as plausible to let the retailer move first. Furthermore, retailers frequently calculate their selling prices by adding a percentage mark-up to their wholesale prices. This allows a retaile...

Flight Testing a Real-Time Hazard Detection System for Safe Lunar Landing on the Rocket-Powered Morpheus Vehicle

Science.gov (United States)

Trawny, Nikolas; Huertas, Andres; Luna, Michael E.; Villalpando, Carlos Y.; Martin, Keith E.; Carson, John M.; Johnson, Andrew E.; Restrepo, Carolina; Roback, Vincent E.

2015-01-01

The Hazard Detection System (HDS) is a component of the ALHAT (Autonomous Landing and Hazard Avoidance Technology) sensor suite, which together provide a lander Guidance, Navigation and Control (GN&C) system with the relevant measurements necessary to enable safe precision landing under any lighting conditions. The HDS consists of a stand-alone compute element (CE), an Inertial Measurement Unit (IMU), and a gimbaled flash LIDAR sensor that are used, in real-time, to generate a Digital Elevation Map (DEM) of the landing terrain, detect candidate safe landing sites for the vehicle through Hazard Detection (HD), and generate hazard-relative navigation (HRN) measurements used for safe precision landing. Following an extensive ground and helicopter test campaign, ALHAT was integrated onto the Morpheus rocket-powered terrestrial test vehicle in March 2014. Morpheus and ALHAT then performed five successful free flights at the simulated lunar hazard field constructed at the Shuttle Landing Facility (SLF) at Kennedy Space Center, for the first time testing the full system on a lunar-like approach geometry in a relevant dynamic environment. During these flights, the HDS successfully generated DEMs, correctly identified safe landing sites and provided HRN measurements to the vehicle, marking the first autonomous landing of a NASA rocket-powered vehicle in hazardous terrain. This paper provides a brief overview of the HDS architecture and describes its in-flight performance.

Laser marking method and device

International Nuclear Information System (INIS)

Okazaki, Yuki; Aoki, Nobutada; Mukai, Narihiko; Sano, Yuji; Yamamoto, Seiji.

1997-01-01

An object is disposed in laser beam permeating liquid or gaseous medium. Laser beams such as CW laser or pulse laser oscillated from a laser device are emitted to the object to apply laser markings with less degradation of identification and excellent corrosion resistance on the surface of the object simply and easily. Upon applying the laser markings, a liquid or gas as a laser beam permeating medium is blown onto the surface of the object, or the liquid or gas in the vicinity of the object is sucked, the laser beam-irradiated portion on the surface can be cooled positively. Accordingly, the laser marking can be formed on the surface of the object with less heat affection to the object. In addition, if the content of a nitrogen gas in the laser beam permeating liquid medium is reduced by degassing to lower than a predetermined value, or the laser beam permeating gaseous medium is formed by an inert gas, a laser marking having high corrosion resistance and reliability can be formed on the surface of the objective member. (N.H.)

''Hazardous'' terminology

International Nuclear Information System (INIS)

Powers, J.

1991-01-01

A number of terms (e.g., ''hazardous chemicals,'' ''hazardous materials,'' ''hazardous waste,'' and similar nomenclature) refer to substances that are subject to regulation under one or more federal environmental laws. State laws and regulations also provide additional, similar, or identical terminology that may be confused with the federally defined terms. Many of these terms appear synonymous, and it easy to use them interchangeably. However, in a regulatory context, inappropriate use of narrowly defined terms can lead to confusion about the substances referred to, the statutory provisions that apply, and the regulatory requirements for compliance under the applicable federal statutes. This information Brief provides regulatory definitions, a brief discussion of compliance requirements, and references for the precise terminology that should be used when referring to ''hazardous'' substances regulated under federal environmental laws. A companion CERCLA Information Brief (EH-231-004/0191) addresses ''toxic'' nomenclature

Mark 4A project training evaluation

Science.gov (United States)

Stephenson, S. N.

1985-01-01

A participant evaluation of a Deep Space Network (DSN) is described. The Mark IVA project is an implementation to upgrade the tracking and data acquisition systems of the dSN. Approximately six hundred DSN operations and engineering maintenance personnel were surveyed. The survey obtained a convenience sample including trained people within the population in order to learn what training had taken place and to what effect. The survey questionnaire used modifications of standard rating scales to evaluate over one hundred items in four training dimensions. The scope of the evaluation included Mark IVA vendor training, a systems familiarization training seminar, engineering training classes, a on-the-job training. Measures of central tendency were made from participant rating responses. Chi square tests of statistical significance were performed on the data. The evaluation results indicated that the effects of different Mark INA training methods could be measured according to certain ratings of technical training effectiveness, and that the Mark IVA technical training has exhibited positive effects on the abilities of DSN personnel to operate and maintain new Mark IVA equipment systems.

Mark 4A project training evaluation

Science.gov (United States)

Stephenson, S. N.

1985-11-01

A participant evaluation of a Deep Space Network (DSN) is described. The Mark IVA project is an implementation to upgrade the tracking and data acquisition systems of the dSN. Approximately six hundred DSN operations and engineering maintenance personnel were surveyed. The survey obtained a convenience sample including trained people within the population in order to learn what training had taken place and to what effect. The survey questionnaire used modifications of standard rating scales to evaluate over one hundred items in four training dimensions. The scope of the evaluation included Mark IVA vendor training, a systems familiarization training seminar, engineering training classes, a on-the-job training. Measures of central tendency were made from participant rating responses. Chi square tests of statistical significance were performed on the data. The evaluation results indicated that the effects of different Mark INA training methods could be measured according to certain ratings of technical training effectiveness, and that the Mark IVA technical training has exhibited positive effects on the abilities of DSN personnel to operate and maintain new Mark IVA equipment systems.

Hazard Analysis Database Report

CERN Document Server

Grams, W H

2000-01-01

The Hazard Analysis Database was developed in conjunction with the hazard analysis activities conducted in accordance with DOE-STD-3009-94, Preparation Guide for U S . Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports, for HNF-SD-WM-SAR-067, Tank Farms Final Safety Analysis Report (FSAR). The FSAR is part of the approved Authorization Basis (AB) for the River Protection Project (RPP). This document describes, identifies, and defines the contents and structure of the Tank Farms FSAR Hazard Analysis Database and documents the configuration control changes made to the database. The Hazard Analysis Database contains the collection of information generated during the initial hazard evaluations and the subsequent hazard and accident analysis activities. The Hazard Analysis Database supports the preparation of Chapters 3 ,4 , and 5 of the Tank Farms FSAR and the Unreviewed Safety Question (USQ) process and consists of two major, interrelated data sets: (1) Hazard Analysis Database: Data from t...

Cooperative Shark Mark Recapture Database (MRDBS)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Shark Mark Recapture Database is a Cooperative Research Program database system used to keep multispecies mark-recapture information in a common format for...

MarkIT büroo = Offices of MarkIT

Index Scriptorium Estoniae

2010-01-01

Tallinnas Pärnu mnt. 102C asuvas büroohoones paikneva MarkIT büroo sisekujundusest. Sisearhitektid Kard Männil (SAB Miu Miu Miu) ja Loreida Hein (Studio La), nende tähtsamate tööde loetelu. Valge büroomööbel on sisearhitektide projekteeritud. Graafika on sisearhitektid ise joonistanud

User’s guide for MapMark4GUI—A graphical user interface for the MapMark4 R package

Science.gov (United States)

Shapiro, Jason

2018-05-29

MapMark4GUI is an R graphical user interface (GUI) developed by the U.S. Geological Survey to support user implementation of the MapMark4 R statistical software package. MapMark4 was developed by the U.S. Geological Survey to implement probability calculations for simulating undiscovered mineral resources in quantitative mineral resource assessments. The GUI provides an easy-to-use tool to input data, run simulations, and format output results for the MapMark4 package. The GUI is written and accessed in the R statistical programming language. This user’s guide includes instructions on installing and running MapMark4GUI and descriptions of the statistical output processes, output files, and test data files.

ThinkHazard!: an open-source, global tool for understanding hazard information

Science.gov (United States)

Fraser, Stuart; Jongman, Brenden; Simpson, Alanna; Nunez, Ariel; Deparday, Vivien; Saito, Keiko; Murnane, Richard; Balog, Simone

2016-04-01

Rapid and simple access to added-value natural hazard and disaster risk information is a key issue for various stakeholders of the development and disaster risk management (DRM) domains. Accessing available data often requires specialist knowledge of heterogeneous data, which are often highly technical and can be difficult for non-specialists in DRM to find and exploit. Thus, availability, accessibility and processing of these information sources are crucial issues, and an important reason why many development projects suffer significant impacts from natural hazards. The World Bank's Global Facility for Disaster Reduction and Recovery (GFDRR) is currently developing a new open-source tool to address this knowledge gap: ThinkHazard! The main aim of the ThinkHazard! project is to develop an analytical tool dedicated to facilitating improvements in knowledge and understanding of natural hazards among non-specialists in DRM. It also aims at providing users with relevant guidance and information on handling the threats posed by the natural hazards present in a chosen location. Furthermore, all aspects of this tool will be open and transparent, in order to give users enough information to understand its operational principles. In this presentation, we will explain the technical approach behind the tool, which translates state-of-the-art probabilistic natural hazard data into understandable hazard classifications and practical recommendations. We will also demonstrate the functionality of the tool, and discuss limitations from a scientific as well as an operational perspective.

Minimal Marking: A Success Story

Directory of Open Access Journals (Sweden)

Anne McNeilly

2014-11-01

Full Text Available The minimal-marking project conducted in Ryerson’s School of Journalism throughout 2012 and early 2013 resulted in significantly higher grammar scores in two first-year classes of minimally marked university students when compared to two traditionally marked classes. The “minimal-marking” concept (Haswell, 1983, which requires dramatically more student engagement, resulted in more successful learning outcomes for surface-level knowledge acquisition than the more traditional approach of “teacher-corrects-all.” Results suggest it would be effective, not just for grammar, punctuation, and word usage, the objective here, but for any material that requires rote-memory learning, such as the Associated Press or Canadian Press style rules used by news publications across North America.

Male and female meadow voles Microtus pennsylvanicus respond differently to scent marks from the top- middle-, and bottom-scent donors of an over-mark

Directory of Open Access Journals (Sweden)

Michael H. FERKIN, Nicholas J. HOBBS, Benjamin D. FERKIN, Adam C.FERKIN, Daniel A. FERKIN

2011-08-01

Full Text Available Previous studies have shown that individuals responded preferentially to the mark of the top-scent donor relative to that of the bottom-scent donor of an over-mark. However, terrestrial mammals are likely to encounter over-marks consisting of the scent marks of more than two same-sex conspecifics in the intersections of runways, near the nests of sexually receptive female conspecifics, and inside and along the borders of the territories of conspecifics. We determined how meadow voles, Microtus pennsylvanicus, respond to the marks of the top-, middle-, and bottom-scent donors of an over-mark. We tested the hypothesis that voles exposed to an over-mark will respond preferentially to the scent marks that were deposited more recently, the scent marks that were on top or near the top of the over-mark, compared to the scent marks that were deposited earlier or near the bottom of the over-mark. Voles spent more time investigating the mark of the top-scent donor than that of the either the middle- or bottom-scent donor. However, males but not female voles spent more time investigating the middle-scent mark than the bottom-scent mark. We also tested the hypothesis that voles evaluate and respond to over-marks differently from single scent marks. Voles spent more time investigating the marks of the top-, middle-, and bottom-scent donors compared to scent marks that were not part of the over-mark. Voles can distinguish among the overlapping scent marks of three scent donors and sex differences exist in the values they appear to attach to each of these scent marks [Current Zoology 57 (4: 441–448, 2011].

Evaluation of copper for divider subassembly in MCO Mark IA and Mark IV scrap fuel baskets

International Nuclear Information System (INIS)

Graves, C.E.

1997-01-01

The K Basin Spent Nuclear Fuel (SNF) Project Multi-Canister Overpack (MCO) subprojection eludes the design and fabrication of a canister that will be used to confine, contain, and maintain fuel in a critically safe array to enable its removal from the K Basins, vacuum drying, transport, staging, hot conditioning, and interim storage (Goldinann 1997). Each MCO consists of a shell, shield plug, fuel baskets (Mark IA or Mark IV), and other incidental equipment. The Mark IA intact and scrap fuel baskets are a safety class item for criticality control and components necessary for criticality control will be constructed from 304L stainless steel. It is proposed that a copper divider subassembly be used in both Mark IA and Mark IV scrap baskets to increase the safety basis margin during cold vacuum drying. The use of copper would increase the heat conducted away from hot areas in the baskets out to the wall of the MCO by both radiative and conductive heat transfer means. Thus copper subassembly will likely be a safety significant component of the scrap fuel baskets. This report examines the structural, cost and corrosion consequences associated with using a copper subassembly in the stainless steel MCO scrap fuel baskets

Multi-Hazard Interactions in Guatemala

Science.gov (United States)

Gill, Joel; Malamud, Bruce D.

2017-04-01

In this paper, we combine physical and social science approaches to develop a multi-scale regional framework for natural hazard interactions in Guatemala. The identification and characterisation of natural hazard interactions is an important input for comprehensive multi-hazard approaches to disaster risk reduction at a regional level. We use five transdisciplinary evidence sources to organise and populate our framework: (i) internationally-accessible literature; (ii) civil protection bulletins; (iii) field observations; (iv) stakeholder interviews (hazard and civil protection professionals); and (v) stakeholder workshop results. These five evidence sources are synthesised to determine an appropriate natural hazard classification scheme for Guatemala (6 hazard groups, 19 hazard types, and 37 hazard sub-types). For a national spatial extent (Guatemala), we construct and populate a "21×21" hazard interaction matrix, identifying 49 possible interactions between 21 hazard types. For a sub-national spatial extent (Southern Highlands, Guatemala), we construct and populate a "33×33" hazard interaction matrix, identifying 112 possible interactions between 33 hazard sub-types. Evidence sources are also used to constrain anthropogenic processes that could trigger natural hazards in Guatemala, and characterise possible networks of natural hazard interactions (cascades). The outcomes of this approach are among the most comprehensive interaction frameworks for national and sub-national spatial scales in the published literature. These can be used to support disaster risk reduction and civil protection professionals in better understanding natural hazards and potential disasters at a regional scale.

Hazard management at the workplace

International Nuclear Information System (INIS)

Hasfazilah Hassan; Azimawati Ahmad; Syed Asraf Fahlawi Wafa S M Ghazi; Hairul Nizam Idris

2005-01-01

Failure to ensure health and safety environment at workplace will cause an accident involving loss to the time, human resource, finance and for the worse case effect the moral value of an organization. If we go through to the cause of the accident, it is impossible to have a totally safety workplace. It is because every process in work activities has it own hazard elements. The purpose of this paper is to discuss the best action to prevent from the hazard with a comprehensive and effectiveness hazard management. Hazard management is the one of the pro-active hazard control. With this we manage to identify and evaluate the hazard and control the hazard risk. Therefore, hazard management should be screened constantly and continuously to make sure work hazard always in control. (Author)

DOE Hazardous Waste Program

International Nuclear Information System (INIS)

Eyman, L.D.; Craig, R.B.

1985-01-01

The goal of the DOE Hazardous Waste Program is to support the implementation and improvement of hazardous-chemical and mixed-radioactive-waste management such that public health, safety, and the environment are protected and DOE missions are effectively accomplished. The strategy for accomplishing this goal is to define the character and magnitude of hazardous wastes emanating from DOE facilities, determine what DOE resources are available to address these problems, define the regulatory and operational constraints, and develop programs and plans to resolve hazardous waste issues. Over the longer term the program will support the adaptation and application of technologies to meet hazardous waste management needs and to implement an integrated, DOE-wide hazardous waste management strategy. 1 reference, 1 figure

An analysis of hospital brand mark clusters.

Science.gov (United States)

Vollmers, Stacy M; Miller, Darryl W; Kilic, Ozcan

2010-07-01

This study analyzed brand mark clusters (i.e., various types of brand marks displayed in combination) used by hospitals in the United States. The brand marks were assessed against several normative criteria for creating brand marks that are memorable and that elicit positive affect. Overall, results show a reasonably high level of adherence to many of these normative criteria. Many of the clusters exhibited pictorial elements that reflected benefits and that were conceptually consistent with the verbal content of the cluster. Also, many clusters featured icons that were balanced and moderately complex. However, only a few contained interactive imagery or taglines communicating benefits.

Glass marking with diode-pumped Nd:YLF laser; Handotai reiki Nd:YLF laser ni yoru glass marking

Energy Technology Data Exchange (ETDEWEB)

Sakai, F.; Hayashi, K. [Sumitomo Heavy Industries, Ltd., Tokyo (Japan)

1996-08-20

The compact marking system based on a beam scanning system in which the fourth harmonic (FHG: 262 nm in wavelength) of a diode-pumped Nd:YLF (Nd:LiYf4) laser is used for the source of ultraviolet light is described. The result of application to the glass marking that caused a problem due to the generation of cracks is also explained. The machining characteristics significantly vary depending on the type of glass. During actual marking, sample processing must be beforehand carried out to optimize the processing conditions after confirming that there is no problem in practical use. For marking on the glass used for liquid-crystal board, it is valid to improve the density of a dot and increase the number of shots per dot for obtaining high visibility. However, cracks may occur in the clearance of each dot because of the thermal effect. Therefore, the processing conditions must be optimized according to the glass type and crack generation state. The generation of cracks can be suppressed by setting the processing conditions to the optimum level. As a result, satisfactory marking is obtained. 8 refs., 6 figs.

Relative Hazard Calculation Methodology

International Nuclear Information System (INIS)

DL Strenge; MK White; RD Stenner; WB Andrews

1999-01-01

The methodology presented in this document was developed to provide a means of calculating the RH ratios to use in developing useful graphic illustrations. The RH equation, as presented in this methodology, is primarily a collection of key factors relevant to understanding the hazards and risks associated with projected risk management activities. The RH equation has the potential for much broader application than generating risk profiles. For example, it can be used to compare one risk management activity with another, instead of just comparing it to a fixed baseline as was done for the risk profiles. If the appropriate source term data are available, it could be used in its non-ratio form to estimate absolute values of the associated hazards. These estimated values of hazard could then be examined to help understand which risk management activities are addressing the higher hazard conditions at a site. Graphics could be generated from these absolute hazard values to compare high-hazard conditions. If the RH equation is used in this manner, care must be taken to specifically define and qualify the estimated absolute hazard values (e.g., identify which factors were considered and which ones tended to drive the hazard estimation)

Civilsamfundets ABC: M for Marked

DEFF Research Database (Denmark)

Lund, Anker Brink; Meyer, Gitte

2016-01-01

Bogstaveligt talt: Hvad er civilsamfundet? Anker Brink Lund og Gitte Meyer fra CBS Center for Civil Society Studies gennemgår civilsamfundet bogstav for bogstav. Vi er nået til M for Marked.......Bogstaveligt talt: Hvad er civilsamfundet? Anker Brink Lund og Gitte Meyer fra CBS Center for Civil Society Studies gennemgår civilsamfundet bogstav for bogstav. Vi er nået til M for Marked....

19 CFR 134.43 - Methods of marking specific articles.

Science.gov (United States)

2010-04-01

... 19 Customs Duties 1 2010-04-01 2010-04-01 false Methods of marking specific articles. 134.43...; DEPARTMENT OF THE TREASURY COUNTRY OF ORIGIN MARKING Method and Location of Marking Imported Articles § 134.43 Methods of marking specific articles. (a) Marking previously required by certain provisions of the...

Lessons learned : pavement marking warranty contract.

Science.gov (United States)

2013-12-01

In 2012, UDOT implemented a performance-based warranty on a portion of an I-15 pavement marking : project. The awarded contract requested a contractor warranty on the implemented markings for a total : duration of six years. This is the first time th...

Minnesota Local Agency Pavement Marking : Mining Existing Data

Science.gov (United States)

2017-11-01

Pavement marking is important for safety. Maximizing pavement marking performance in terms of increased retroreflectivity, within limited budget constraints, allows agencies to make better decisions toward providing more effective pavement marking pe...

Natural hazards science strategy

Science.gov (United States)

Holmes, Robert R.; Jones, Lucile M.; Eidenshink, Jeffery C.; Godt, Jonathan W.; Kirby, Stephen H.; Love, Jeffrey J.; Neal, Christina A.; Plant, Nathaniel G.; Plunkett, Michael L.; Weaver, Craig S.; Wein, Anne; Perry, Suzanne C.

2012-01-01

The mission of the U.S. Geological Survey (USGS) in natural hazards is to develop and apply hazard science to help protect the safety, security, and economic well-being of the Nation. The costs and consequences of natural hazards can be enormous, and each year more people and infrastructure are at risk. USGS scientific research—founded on detailed observations and improved understanding of the responsible physical processes—can help to understand and reduce natural hazard risks and to make and effectively communicate reliable statements about hazard characteristics, such as frequency, magnitude, extent, onset, consequences, and where possible, the time of future events.To accomplish its broad hazard mission, the USGS maintains an expert workforce of scientists and technicians in the earth sciences, hydrology, biology, geography, social and behavioral sciences, and other fields, and engages cooperatively with numerous agencies, research institutions, and organizations in the public and private sectors, across the Nation and around the world. The scientific expertise required to accomplish the USGS mission in natural hazards includes a wide range of disciplines that this report refers to, in aggregate, as hazard science.In October 2010, the Natural Hazards Science Strategy Planning Team (H–SSPT) was charged with developing a long-term (10-year) Science Strategy for the USGS mission in natural hazards. This report fulfills that charge, with a document hereinafter referred to as the Strategy, to provide scientific observations, analyses, and research that are critical for the Nation to become more resilient to natural hazards. Science provides the information that decisionmakers need to determine whether risk management activities are worthwhile. Moreover, as the agency with the perspective of geologic time, the USGS is uniquely positioned to extend the collective experience of society to prepare for events outside current memory. The USGS has critical statutory

Mark Twain: inocente ou pecador? = Mark Twain: innocent or sinner?

Directory of Open Access Journals (Sweden)

Heloisa Helou Doca

2009-01-01

Full Text Available A leitura cuidadosa do texto do “Tratado de Paris”, em 1900, leva Mark Twain a concluir que a intenção política norte-americana era, claramente, a de subjugação. Declara-se, abertamente, antiimperialista, nesse momento, apesar das inúmeras críticasrecebidas por antagonistas políticos que defendiam o establishment dos Estados Unidos. Após viajar para a Europa e Oriente, em 1867, como correspondente do jornal Daily Alta Califórnia, Mark Twain publica, em 1869, seu relato de viagem, The Innocents Abroad or TheNew Pilgrim’s Progress. Nosso estudo demonstra que o autor, apesar das diversas máscaras usadas em seus relatos, narra histórias, culturas e tradições, tanto da Europa quanto do Oriente, já com os olhos bem abertos pelo viés antiimperialista. Faz uso da paródia, sátira, ironia e humor para dessacralizar impérios, monarcas e a Igreja que subjugavam os mais fracos, iluminando, desde então, os estudos sobre culturas. Nosso estudo, outrossim, faz uma reflexão sobre cultura, tradição e o olhar do viajante, justificando o “olhar inocente” do narrador em seu relato.After carefully reading the Treaty of Paris in 1900, Mark Twain concluded that the goal of U.S. policy was clearly one ofsubjugation. He openly declared himself an anti-imperialist at that time, in spite of the numerous criticisms he received from political opponents who supported the United States status quo. After traveling to Europe and the East in 1867 as a correspondent for The DailyAlta California newspaper, Mark Twain published his travel report, The Innocents Abroad or The New Pilgrim’s Progress in 1869. Our study demonstrates that the author, in spite of using different guises in his reports, narrated histories, cultures and traditions – from both Europe and the East – with a viewpoint already imbued by his anti-imperialistic ideals. Twain made use of parody, satire, irony and humor within his texts in order to desecrate empires,monarchs and

Do employers prefer Mark over Mohammed?

NARCIS (Netherlands)

Iris Andriessen; Eline Nievers; Laila Faulk; Jaco Dagevos

2010-01-01

Original title: Liever Mark dan Mohammed? Does Mohammed have less chance of succeeding on the Dutch labour market than Mark, even though they both have the same qualifications and work experience? And are employers less friendly towards Sonaya than Paula? This study investigates the

Globe of Natural Hazard - A new assessment tool for risk managers

Science.gov (United States)

Siebert, A. C.

2009-04-01

A large number of tropical cyclones and the earthquake in Sichuan made 2008 one of the most devastating years on record. Throughout the world, more than 220,000 people died as a result of natural catastrophes this year. Overall losses totaled some US 200bn (2007: US 82bn). Insured losses in 2008 rose to US 45bn, about 50% higher than in the previous year. Mainly driven by high losses from weather-related natural catastrophes, 2008 was - on the basis of figures adjusted for inflation - even the third most expensive year on record for the insurance industry, exceeded only by the hurricane year of 2005 and by 1995, the year of the Kobe earthquake. Munich Re, a worldwide operating reinsurance company, is a world leader in terms of investigating risks from natural hazards of all kinds. 2008 has again shown the insurance industry how important it is to analyse risks like natural hazards and climate change in all their facets and to manage the insurance business accordingly. An excellent example of the wealth of knowledge Munich Re has developed in natural hazard assessment is the DVD "Globe of Natural Hazards". It combines the geoscientific data and findings Munich Re has accumulated over a period of 35 years. First devised as a wall-map in 1978, the product has established itself as a standard work for the identification, exposure assessment and risk management of natural hazards. Over 80,000 copies of the CD-ROM version of 2000 have been provided to clients - a mark achieved by no other service product in Munich Re's history. Since the beginning of 2009, the fully updated fourth-generation version has been available. The bilingual DVD (German and English) shows natural hazards and climate effects at a glance: the global maps are presented on a 3D globe, underlaid with satellite images. The hazard complexes of hail, tornado and winter storms have been completely revised and flood incorporated as a new hazard. Users can intuitively home in on and enlarge any location on

Analysis of Complex Marine Hazards on the Romanian Black Sea Shelf Using Combined Geophysical Methods

Science.gov (United States)

Samoila, I. V.; Radulescu, V.; Moise, G.; Diaconu, A.; Radulescu, R.

2017-12-01

Combined geophysical acquisition technologies including High Resolution 2D Seismic (HR2D), Multi-Beam Echo-Sounding (MBES), Sub-Bottom Profiling (SBP) and Magnetometry were used in the Western Black Sea (offshore Romania) to identify possible geohazards, such as gas escaping surface sediments and tectonic hazard areas up to 1 km below the seafloor. The National Project was funded by the Research and Innovation Ministry of Romania, and has taken place over 1.5 years with the purpose of creating risk maps for the surveyed pilot area. Using an array of geophysical methods and creating a workflow to identify geohazard susceptible areas on the Romanian Black Sea continental shelf is important and beneficial for future research projects. The SBP and MBES data show disturbed areas that can be interpreted as gas escapes on the surface of the seafloor, and some escapes were confirmed on the HR2D profiles. Shallow gas indicators like gas chimneys and acoustic blanking are usually delimited by vertical, sub-vertical and/or quasi-horizontal faults that mark possible hazard areas on shallow sedimentary sections. Interpreted seismic profiles show three main markers: one delimiting the Pliocene-Quaternary boundary and two for the Miocene (Upper and Lower). Vertical and quasi-horizontal faults are characteristic for the Upper Miocene, while the Lower Miocene has NW-SE horizontal faults. Faults and possible hazard areas were marked on seismic sections and were further correlated with the MBES, SBP, Magnetometry and previously recorded data, such as earthquake epicenters scattered offshore in the Western Black Sea. The main fault systems likely to cause those earthquakes also aid the migration of gas if the faults are not sealed. We observed that the gas escapes were correlated with faults described on the recent seismic profiles. Mapping hazard areas will have an important contribution to better understand the recent evolution of the Western Black Sea basin but also for projecting

[Werkgartner's muzzle imprint mark--a literature study].

Science.gov (United States)

Geserick, Gunther; Vendura, Klaus; Wirth, Ingo

2009-01-01

Since Werkgartner described and correctly interpreted the muzzle imprint mark around the gunshot entrance wound in 1922, this finding has been generally accepted as a sign of a contact shot. In further studies, it could finally be clarified that the muzzle imprint mark is caused by the expansive power of the powder gases with pressure on and abrasion of the skin at the muzzle (weapon imprint). Its shape depends on the firearm, the ammunition and the anatomical conditions, but does not require a bullet. Examinations under a magnifying glass microscope and histological investigations can complete the macroscopic findings. Occasionally, the muzzle imprint mark requires a certain "drying period" in order to become clearly visible. In rare cases, muzzle imprint marks also form on textiles perforated by the projectile. Characteristically shaped muzzled imprint marks can provide clues to the type of the firearm and its position at the time of discharge.

Radiation hazards

International Nuclear Information System (INIS)

Rausch, L.

1979-01-01

On a scientific basis and with the aid of realistic examples, the author gives a popular introduction to an understanding and judgment of the public discussion over radiation hazards: Uses and hazards of X-ray examinations, biological radiation effects, civilisation risks in comparison, origins and explanation of radiation protection regulations. (orig.) [de

19 CFR 11.9 - Special marking on certain articles.

Science.gov (United States)

2010-04-01

... 19 Customs Duties 1 2010-04-01 2010-04-01 false Special marking on certain articles. 11.9 Section... OF THE TREASURY PACKING AND STAMPING; MARKING Marking § 11.9 Special marking on certain articles. (a... of additional U.S. Note 4, Chapter 91. If any article so required to be marked is found not to be...

Hazardous situation in the MR bore: induction in ECG leads causes fire

International Nuclear Information System (INIS)

Kugel, Harald; Bremer, Christoph; Fischbach, Roman; Lenzen, Horst; Tombach, Bernd; Heindel, Walter; Pueschel, Marco; Aken, Hugo van

2003-01-01

There is a potential hazard during examinations of patients with attached or implanted long conductors, e.g. ECG leads: an MR exam of the lumbar spine of a patient was performed in a 1.5-T scanner under ECG monitoring using equipment marked as MR compatible. Standard cabling of 370-cm length was guided without loops from the electrodes through the caudal opening of the magnet bore. During a sagittal T1-weighted turbo-spin-echo scan suddenly a flame of approximately 3 cm arose from the patient's shirt, close to the position of the electrodes. The supervising anaesthesiologist extinguished the flames with his hands. A subsequent physical examination revealed second- to third-degree burns. The analysis of the incident revealed that high voltages can be induced in straight conductors without loops as ECG cables by coupling with the electric component of the HF field. Local heating or sparking can cause an open flame at the position of the electrodes. This danger exists even with ECG equipment that is specifically marked as MR compatible. (orig.)

Hazard screening application guide

International Nuclear Information System (INIS)

1992-06-01

The basic purpose of hazard screening is to group precesses, facilities, and proposed modifications according to the magnitude of their hazards so as to determine the need for and extent of follow on safety analysis. A hazard is defined as a material, energy source, or operation that has the potential to cause injury or illness in human beings. The purpose of this document is to give guidance and provide standard methods for performing hazard screening. Hazard screening is applied to new and existing facilities and processes as well as to proposed modifications to existing facilities and processes. The hazard screening process evaluates an identified hazards in terms of the effects on people, both on-site and off-site. The process uses bounding analyses with no credit given for mitigation of an accident with the exception of certain containers meeting DOT specifications. The process is restricted to human safety issues only. Environmental effects are addressed by the environmental program. Interfaces with environmental organizations will be established in order to share information

Software safety hazard analysis

International Nuclear Information System (INIS)

Lawrence, J.D.

1996-02-01

Techniques for analyzing the safety and reliability of analog-based electronic protection systems that serve to mitigate hazards in process control systems have been developed over many years, and are reasonably well understood. An example is the protection system in a nuclear power plant. The extension of these techniques to systems which include digital computers is not well developed, and there is little consensus among software engineering experts and safety experts on how to analyze such systems. One possible technique is to extend hazard analysis to include digital computer-based systems. Software is frequently overlooked during system hazard analyses, but this is unacceptable when the software is in control of a potentially hazardous operation. In such cases, hazard analysis should be extended to fully cover the software. A method for performing software hazard analysis is proposed in this paper

49 CFR 178.338-18 - Marking.

Science.gov (United States)

2010-10-01

... pounds. (7) Maximum design density of lading (Max. Lading density), in pounds per gallon. (8) Material... cryogenic liquid, in hours, and the name of that cryogenic liquid (MRHT __ hrs, name of cryogenic liquid). Marked rated holding marking for additional cryogenic liquids may be displayed on or adjacent to the...

7 CFR 956.162 - Container markings.

Science.gov (United States)

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Container markings. 956.162 Section 956.162... WALLA VALLEY OF SOUTHEAST WASHINGTON AND NORTHEAST OREGON Rules and Regulations § 956.162 Container markings. Effective April 15, 1997, no handler shall ship any container of Walla Walla Sweet Onions except...

Differential Signature of the Centrosomal MARK4 Isoforms in Glioma

Directory of Open Access Journals (Sweden)

Ivana Magnani

2011-01-01

Full Text Available Background: MAP/microtubule affinity-regulating kinase 4 (MARK4 is a serine-threonine kinase expressed in two spliced isoforms, MARK4L and MARK4S, of which MARK4L is a candidate for a role in neoplastic transformation. Methods: We performed mutation analysis to identify sequence alterations possibly affecting MARK4 expression. We then investigated the MARK4L and MARK4S expression profile in 21 glioma cell lines and 36 tissues of different malignancy grades, glioblastoma-derived cancer stem cells (GBM CSCs and mouse neural stem cells (NSCs by real-time PCR, immunoblotting and immunohistochemistry. We also analyzed the sub-cellular localisation of MARK4 isoforms in glioma and normal cell lines by immunofluorescence. Results: Mutation analysis rules out sequence variations as the cause of the altered MARK4 expression in glioma. Expression profiling confirms that MARK4L is the predominant isoform, whereas MARK4S levels are significantly decreased in comparison and show an inverse correlation with tumour grade. A high MARK4L/MARK4S ratio also characterizes undifferentiated cells, such as GBM CSCs and NSCs. Accordingly, only MARK4L is expressed in brain neurogenic regions. Moreover, while both MARK4 isoforms are localised to the centrosome and midbody in glioma and normal cells, the L isoform exhibits an additional nucleolar localisation in tumour cells. Conclusions: The observed switch towards MARK4L suggests that the balance between the MARK4 isoforms is carefully guarded during neural differentiation but may be subverted in gliomagenesis. Moreover, the MARK4L nucleolar localisation in tumour cells features this MARK4 isoform as a nucleolus-associated tumour marker.

Marks on the petroleum fiscality

International Nuclear Information System (INIS)

2007-02-01

This document offers some marks on the petroleum fiscality in France: the taxes as the 'accises' and the 'TVA', the part of the taxes in the sale price at the service station, the comparison with other countries of Europe, the tax revenues and the Government budget. It provides also marks on the fuels prices formation (margins), the world petroleum markets (supply and demand) and the part of the petroleum companies on the petroleum market. (A.L.B.)

14 CFR 1203.501 - Applying derivative classification markings.

Science.gov (United States)

2010-01-01

... INFORMATION SECURITY PROGRAM Derivative Classification § 1203.501 Applying derivative classification markings. Persons who apply derivative classification markings shall: (a) Observe and respect original... 14 Aeronautics and Space 5 2010-01-01 2010-01-01 false Applying derivative classification markings...

Job Hazard Analysis

National Research Council Canada - National Science Library

1998-01-01

.... Establishing proper job procedures is one of the benefits of conducting a job hazard analysis carefully studying and recording each step of a job, identifying existing or potential job hazards...

Aluminum-Oxide Temperatures on the Mark VB, VE, VR, 15, and Mark 25 Assemblies

International Nuclear Information System (INIS)

Aleman, S.E.

2001-01-01

The task was to compute the maximum aluminum-oxide and oxide-coolant temperatures of assemblies cladded in 99+ percent aluminum. The assemblies considered were the Mark VB, VE, V5, 15 and 25. These assemblies consist of nested slug columns with individual uranium slugs cladded in aluminum cans. The CREDIT code was modified to calculate the oxide film thickness and the aluminum-oxide temperature at each axial increment. This information in this report will be used to evaluate the potential for cladding corrosion of the Mark 25 assembly

Introduction: Hazard mapping

Science.gov (United States)

Baum, Rex L.; Miyagi, Toyohiko; Lee, Saro; Trofymchuk, Oleksandr M

2014-01-01

Twenty papers were accepted into the session on landslide hazard mapping for oral presentation. The papers presented susceptibility and hazard analysis based on approaches ranging from field-based assessments to statistically based models to assessments that combined hydromechanical and probabilistic components. Many of the studies have taken advantage of increasing availability of remotely sensed data and nearly all relied on Geographic Information Systems to organize and analyze spatial data. The studies used a range of methods for assessing performance and validating hazard and susceptibility models. A few of the studies presented in this session also included some element of landslide risk assessment. This collection of papers clearly demonstrates that a wide range of approaches can lead to useful assessments of landslide susceptibility and hazard.

Barrow hazards survey

International Nuclear Information System (INIS)

1980-06-01

Following a series of public meetings at which PERG presented the results of a literature review and site specific accident study of the hazards of the maritime transport of spent nuclear reactor fuel to Barrow (en route to the Windscale reprocessing works), PERG was requested by the Planning Committee of Barrow Town Council to prepare an assessment of the interaction of the hazards arising from the concentration of nuclear activities in the area with those of a proposed gas-terminal. This report presents a preliminary review of the Environmental Impact Assessments prepared by the Borough Surveyor and a critical appraisal of the hazard analyses undertaken by the Health and Safety Executive, and the consultants to Cumbria County Council on this matter, the Safety and Reliability Directorate of the United Kingdom Atomic Energy Authority. After a general and historical introduction, the document continues under the following headings: a description of the hazards (BNFL spent fuel shipments; the gas terminal; gas condensate storage; the Vickers shipyard (involving nuclear powered submarines)); the interaction of hazards; planning implications and democratic decisions; recommendations. (U.K.)

76 FR 4823 - Hazardous Waste Management System; Identifying and Listing Hazardous Waste Exclusion

Science.gov (United States)

2011-01-27

... Waste Management System; Identifying and Listing Hazardous Waste Exclusion AGENCY: Environmental... hazardous wastes. The Agency has decided to grant the petition based on an evaluation of waste-specific... excludes the petitioned waste from the requirements of hazardous waste regulations under the Resource...

Structural comparison of hazardous and non-hazardous coals based on gas sorption experiments

Energy Technology Data Exchange (ETDEWEB)

Lakatos, J.; Toth, J. [Research Lab. for Mining Chemistry, Hungarian Academy of Sciences, Miskolc-Egyetemvaros (Hungary); Radnai-Gyoengyoes, Z. [Geopard Ltd., Pecs (Hungary); Bokanyi, L. [Miskolc Univ., Miskolc-Egyetemvaros (Hungary). Dept. of Process Engineering

1997-12-31

Comparison of carbon-dioxide and propane sorption at ambient temperature was used for characterising the difference of the structure of hazardous and non hazardous coals. However, hazardous coals were found more microporous or contain more closed pores than non hazardous ones, this difference couldn`t have been enlarged and attributed to one petrographic component by producing the density fractions. Gas sorption isobars (nitrogen, methane, ethane) are proposed to make a distinction between fine pore structure of coals. (orig.)

Serviceable pavement marking retroreflectivity levels : technical report.

Science.gov (United States)

2009-03-01

This research addressed an array of issues related to measuring pavement markings retroreflectivity, factors : related to pavement marking performance, subjective evaluation process, best practices for using mobile : retroreflectometers, sampling pav...

46 CFR 108.645 - Markings on lifesaving appliances.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Markings on lifesaving appliances. 108.645 Section 108.645 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Equipment Markings and Instructions § 108.645 Markings on lifesaving appliances. (a...

25 CFR 141.16 - Price marking.

Science.gov (United States)

2010-04-01

... 25 Indians 1 2010-04-01 2010-04-01 false Price marking. 141.16 Section 141.16 Indians BUREAU OF... AND ZUNI RESERVATIONS General Business Practices § 141.16 Price marking. The price of each article... visible to the customer and that affords the customer a reasonable opportunity to learn the price of the...

Informing Workers of Chemical Hazards: The OSHA Hazard Communication Standard.

Science.gov (United States)

American Chemical Society, Washington, DC.

Practical information on how to implement a chemical-related safety program is outlined in this publication. Highlights of the federal Occupational Safety and Health Administrations (OSHA) Hazard Communication Standard are presented and explained. These include: (1) hazard communication requirements (consisting of warning labels, material safety…

A decision model for the risk management of hazardous processes

International Nuclear Information System (INIS)

Holmberg, J.E.

1997-03-01

A decision model for risk management of hazardous processes as an optimisation problem of a point process is formulated in the study. In the approach, the decisions made by the management are divided into three categories: (1) planned process lifetime, (2) selection of the design and, (3) operational decisions. These three controlling methods play quite different roles in the practical risk management, which is also reflected in our approach. The optimisation of the process lifetime is related to the licensing problem of the process. It provides a boundary condition for a feasible utility function that is used as the actual objective function, i.e., maximizing the process lifetime utility. By design modifications, the management can affect the inherent accident hazard rate of the process. This is usually a discrete optimisation task. The study particularly concentrates upon the optimisation of the operational strategies given a certain design and licensing time. This is done by a dynamic risk model (marked point process model) representing the stochastic process of events observable or unobservable to the decision maker. An optimal long term control variable guiding the selection of operational alternatives in short term problems is studied. The optimisation problem is solved by the stochastic quasi-gradient procedure. The approach is illustrated by a case study. (23 refs.)

Transport of hazardous goods

International Nuclear Information System (INIS)

1989-01-01

The course 'Transport of hazardous goods' was held in Berlin in November 1988 in cooperation with the Bundesanstalt fuer Materialforschung und -pruefung. From all lecturs, two are recorded separately: 'Safety of tank trucks - requirements on the tank, development possibiities of active and passive safety' and 'Requirements on the transport of radioactive materials - possible derivations for other hazardous goods'. The other lectures deal with hazardous goods law, requirements on packinging, risk assessment, railroad transport, hazardous goods road network, insurance matters, EC regulations, and waste tourism. (HSCH) [de

Seismic hazard maps for Haiti

Science.gov (United States)

Frankel, Arthur; Harmsen, Stephen; Mueller, Charles; Calais, Eric; Haase, Jennifer

2011-01-01

We have produced probabilistic seismic hazard maps of Haiti for peak ground acceleration and response spectral accelerations that include the hazard from the major crustal faults, subduction zones, and background earthquakes. The hazard from the Enriquillo-Plantain Garden, Septentrional, and Matheux-Neiba fault zones was estimated using fault slip rates determined from GPS measurements. The hazard from the subduction zones along the northern and southeastern coasts of Hispaniola was calculated from slip rates derived from GPS data and the overall plate motion. Hazard maps were made for a firm-rock site condition and for a grid of shallow shear-wave velocities estimated from topographic slope. The maps show substantial hazard throughout Haiti, with the highest hazard in Haiti along the Enriquillo-Plantain Garden and Septentrional fault zones. The Matheux-Neiba Fault exhibits high hazard in the maps for 2% probability of exceedance in 50 years, although its slip rate is poorly constrained.

46 CFR 199.176 - Markings on lifesaving appliances.

Science.gov (United States)

2010-10-01

... ARRANGEMENTS LIFESAVING SYSTEMS FOR CERTAIN INSPECTED VESSELS Requirements for All Vessels § 199.176 Markings on lifesaving appliances. (a) Lifeboats and rescue boats. Each lifeboat and rescue boat must be plainly marked as follows: (1) Each side of each lifeboat and rescue boat bow must be marked in block...

INTERNAL HAZARDS ANALYSIS FOR LICENSE APPLICATION

Energy Technology Data Exchange (ETDEWEB)

R.J. Garrett

2005-02-17

The purpose of this internal hazards analysis is to identify and document the internal hazards and potential initiating events associated with preclosure operations of the repository at Yucca Mountain. Internal hazards are those hazards presented by the operation of the facility and by its associated processes that can potentially lead to a radioactive release or cause a radiological hazard. In contrast to external hazards, internal hazards do not involve natural phenomena and external man-made hazards. This internal hazards analysis was performed in support of the preclosure safety analysis and the License Application for the Yucca Mountain Project. The methodology for this analysis provides a systematic means to identify internal hazards and potential initiating events that may result in a radiological hazard or radiological release during the repository preclosure period. These hazards are documented in tables of potential internal hazards and potential initiating events (Section 6.6) for input to the repository event sequence categorization process. The results of this analysis will undergo further screening and analysis based on the criteria that apply to the performance of event sequence analyses for the repository preclosure period. The evolving design of the repository will be re-evaluated periodically to ensure that internal hazards that have not been previously evaluated are identified.

INTERNAL HAZARDS ANALYSIS FOR LICENSE APPLICATION

International Nuclear Information System (INIS)

Garrett, R.J.

2005-01-01

The purpose of this internal hazards analysis is to identify and document the internal hazards and potential initiating events associated with preclosure operations of the repository at Yucca Mountain. Internal hazards are those hazards presented by the operation of the facility and by its associated processes that can potentially lead to a radioactive release or cause a radiological hazard. In contrast to external hazards, internal hazards do not involve natural phenomena and external man-made hazards. This internal hazards analysis was performed in support of the preclosure safety analysis and the License Application for the Yucca Mountain Project. The methodology for this analysis provides a systematic means to identify internal hazards and potential initiating events that may result in a radiological hazard or radiological release during the repository preclosure period. These hazards are documented in tables of potential internal hazards and potential initiating events (Section 6.6) for input to the repository event sequence categorization process. The results of this analysis will undergo further screening and analysis based on the criteria that apply to the performance of event sequence analyses for the repository preclosure period. The evolving design of the repository will be re-evaluated periodically to ensure that internal hazards that have not been previously evaluated are identified

PREOPERATIVE ENDOSCOPIC MARKING OF UNPALPABLE COLONIC TUMORS

Directory of Open Access Journals (Sweden)

A. L. Goncharov

2013-01-01

Full Text Available The identification of small colon lesions is one of the major problems in laparoscopic colonic resection.Research objective: to develop a technique of visualization of small tumors of a colon by preoperative endoscopic marking of a tumor.Materials and methods. In one day prior to operation to the patient after bowel preparation the colonoscopy is carried out. In the planned point near tumor on antimesentery edge the submucous infiltration of marking solution (Micky Sharpz blue tattoo pigment, UK is made. The volume of entered solution of 1–3 ml. In only 5 months of use of a technique preoperative marking to 14 patients with small (the size of 1–3 cm malignant tumors of the left colon is performed.Results. The tattoo mark was well visualized by during operation at 13 of 14 patients. In all cases we recorded no complications. Time of operation with preoperative marking averaged 108 min, that is significantly less in comparison with average time of operation with an intra-operative colonoscopy – 155 min (р < 0.001.Conclusions. The first experience of preoperative endoscopic marking of non palpable small tumors of a colon is encouraging. Performance of a technique wasn't accompanied by complications and allowed to reduce significantly time of operation and to simplify conditions of performance of operation.

49 CFR 1520.13 - Marking SSI.

Science.gov (United States)

2010-10-01

... SECURITY INFORMATION § 1520.13 Marking SSI. (a) Marking of paper records. In the case of paper records... back cover, including a binder cover or folder, if the document has a front and back cover; (2) Any.... 552 and 49 CFR parts 15 and 1520. (d) Other types of records. In the case of non-paper records that...

76 FR 55846 - Hazardous Waste Management System: Identification and Listing of Hazardous Waste: Carbon Dioxide...

Science.gov (United States)

2011-09-09

... carbon dioxide (CO 2 ) streams that are hazardous from the definition of hazardous waste, provided these... management under the Resource Conservation and Recovery Act (RCRA) to conditionally exclude carbon dioxide... 2050-AG60 Hazardous Waste Management System: Identification and Listing of Hazardous Waste: Carbon...

9 CFR 316.13 - Marking of outside containers.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Marking of outside containers. 316.13... INSPECTION AND CERTIFICATION MARKING PRODUCTS AND THEIR CONTAINERS § 316.13 Marking of outside containers. (a... domestic commerce is moved from an official establishment, the outside container shall bear an official...

Infrared technique for decoding of invisible laser markings

Science.gov (United States)

Haferkamp, Heinz; Jaeschke, Peter; Stein, Johannes; Goede, Martin

2002-03-01

Counterfeiting and product piracy continues to be an important issue not only for the Western industry, but also for the society in general. Due to the drastic increase in product imitation and the request for plagiarism protection as well as for reducing thefts there is a high interest in new protection methods providing new security features. The method presented here consists of security markings which are included below paint layers. These markings are invisible for the human eye due to the non-transparency of the upper layers in the visible spectral range. However, the markings can be detected by an infrared technique taking advantage on the partial transparency of the upper paint layers in the IR-region. Metal sheets are marked using laser radiation. The beam of a Nd:YAG-laser provides a modification of the surface structure, resulting in dark markings due to the annealing effect. After coating of the laser-marked material, the markings are invisible for the bare eye. In order to read out the invisible information below the coating, an infrared reflection technique is used. The samples are illuminated with halogen lamps or infrared radiators. Many coating materials (i. e. paints) show a certain transparency in the mid-infrared region, especially between 3 - 5 micrometers . The reflected radiation is detected using an IR-camera with a sensitivity range from 3.4 - 5 micrometers . Due to the different reflection properties between the markings and their surrounding, the information can be detected.

Forensic surface metrology: tool mark evidence.

Science.gov (United States)

Gambino, Carol; McLaughlin, Patrick; Kuo, Loretta; Kammerman, Frani; Shenkin, Peter; Diaczuk, Peter; Petraco, Nicholas; Hamby, James; Petraco, Nicholas D K

2011-01-01

Over the last several decades, forensic examiners of impression evidence have come under scrutiny in the courtroom due to analysis methods that rely heavily on subjective morphological comparisons. Currently, there is no universally accepted system that generates numerical data to independently corroborate visual comparisons. Our research attempts to develop such a system for tool mark evidence, proposing a methodology that objectively evaluates the association of striated tool marks with the tools that generated them. In our study, 58 primer shear marks on 9 mm cartridge cases, fired from four Glock model 19 pistols, were collected using high-resolution white light confocal microscopy. The resulting three-dimensional surface topographies were filtered to extract all "waviness surfaces"-the essential "line" information that firearm and tool mark examiners view under a microscope. Extracted waviness profiles were processed with principal component analysis (PCA) for dimension reduction. Support vector machines (SVM) were used to make the profile-gun associations, and conformal prediction theory (CPT) for establishing confidence levels. At the 95% confidence level, CPT coupled with PCA-SVM yielded an empirical error rate of 3.5%. Complementary, bootstrap-based computations for estimated error rates were 0%, indicating that the error rate for the algorithmic procedure is likely to remain low on larger data sets. Finally, suggestions are made for practical courtroom application of CPT for assigning levels of confidence to SVM identifications of tool marks recorded with confocal microscopy. Copyright © 2011 Wiley Periodicals, Inc.

HAZARD ANALYSIS SOFTWARE

International Nuclear Information System (INIS)

Sommer, S; Tinh Tran, T.

2008-01-01

Washington Safety Management Solutions, LLC developed web-based software to improve the efficiency and consistency of hazard identification and analysis, control selection and classification, and to standardize analysis reporting at Savannah River Site. In the new nuclear age, information technology provides methods to improve the efficiency of the documented safety analysis development process which includes hazard analysis activities. This software provides a web interface that interacts with a relational database to support analysis, record data, and to ensure reporting consistency. A team of subject matter experts participated in a series of meetings to review the associated processes and procedures for requirements and standard practices. Through these meetings, a set of software requirements were developed and compiled into a requirements traceability matrix from which software could be developed. The software was tested to ensure compliance with the requirements. Training was provided to the hazard analysis leads. Hazard analysis teams using the software have verified its operability. The software has been classified as NQA-1, Level D, as it supports the analysis team but does not perform the analysis. The software can be transported to other sites with alternate risk schemes. The software is being used to support the development of 14 hazard analyses. User responses have been positive with a number of suggestions for improvement which are being incorporated as time permits. The software has enforced a uniform implementation of the site procedures. The software has significantly improved the efficiency and standardization of the hazard analysis process

Microscopic saw mark analysis: an empirical approach.

Science.gov (United States)

Love, Jennifer C; Derrick, Sharon M; Wiersema, Jason M; Peters, Charles

2015-01-01

Microscopic saw mark analysis is a well published and generally accepted qualitative analytical method. However, little research has focused on identifying and mitigating potential sources of error associated with the method. The presented study proposes the use of classification trees and random forest classifiers as an optimal, statistically sound approach to mitigate the potential for error of variability and outcome error in microscopic saw mark analysis. The statistical model was applied to 58 experimental saw marks created with four types of saws. The saw marks were made in fresh human femurs obtained through anatomical gift and were analyzed using a Keyence digital microscope. The statistical approach weighed the variables based on discriminatory value and produced decision trees with an associated outcome error rate of 8.62-17.82%. © 2014 American Academy of Forensic Sciences.

Perception of scent over-marks by golden hamsters (Mesocricetus auratus): novel mechanisms for determining which individual's mark is on top.

Science.gov (United States)

Johnston, R E; Bhorade, A

1998-09-01

Hamsters preferentially remember or value the top scent of a scent over-mark. What cues do they use to do this? Using habituation-discrimination techniques, we exposed male golden hamsters (Mesocricetus auratus) on 3 to 4 trials to genital over-marks from 2 females and then tested subjects for their familiarity with these 2 scents compared with that of a novel female's secretion. Preferential memory for 1 of the 2 individuals' scents did not occur if the 2 marks did not overlap or did not overlap but differed in age, but it did occur if a region of overlap existed or 1 mark apparently occluded another (but did not overlap it). Thus, hamsters use regions of overlap and the spatial configuration of scents to evaluate over-marks. These phenomena constitute evidence for previously unsuspected perceptual abilities, including olfactory scene analysis, which is analogous to visual and auditory scene analysis.

Bite marks on skin and clay: A comparative analysis

Directory of Open Access Journals (Sweden)

R.K. Gorea

2014-12-01

Full Text Available Bite marks are always unique because teeth are distinctive. Bite marks are often observed at the crime scene in sexual and in physical assault cases on the skin of the victims and sometimes on edible leftovers in burglary cases. This piece of evidence is often ignored, but if properly harvested and investigated, bite marks may prove useful in apprehending and successfully prosecuting the criminals. Due to the importance of bite marks, we conducted a progressive randomised experimental study conducted on volunteers. A total of 188 bite marks on clay were studied. Based on these findings, 93.34% of the volunteers could be identified from the bite marks on the clay. In addition, 201 impressions on skin were studied, and out of these cases, 41.01% of the same volunteers could be identified based on the bite mark impressions on the skin.

Hazardous Chemicals

Centers for Disease Control (CDC) Podcasts

Chemicals are a part of our daily lives, providing many products and modern conveniences. With more than three decades of experience, The Centers for Disease Control and Prevention (CDC) has been in the forefront of efforts to protect and assess people's exposure to environmental and hazardous chemicals. This report provides information about hazardous chemicals and useful tips on how to protect you and your family from harmful exposure.

Technical Guidance for Hazardous Analysis, Emergency Planning for Extremely Hazardous Substances

Science.gov (United States)

This current guide supplements NRT-1 by providing technical assistance to LEPCs to assess the lethal hazards related to potential airborne releases of extremely hazardous substances (EHSs) as designated under Section 302 of Title Ill of SARA.

Hypergol Maintenance Facility Hazardous Waste South Staging Areas, SWMU 070 Corrective Measures Implementation

Science.gov (United States)

Miller, Ralinda R.

2016-01-01

This document presents the Corrective Measures Implementation (CMI) Year 10 Annual Report for implementation of corrective measures at the Hypergol Maintenance Facility (HMF) Hazardous Waste South Staging Areas at Kennedy Space Center, Florida. The work is being performed by Tetra Tech, Inc., for the National Aeronautics and Space Administration (NASA) under Indefinite Delivery Indefinite Quantity (IDIQ) NNK12CA15B, Task Order (TO) 07. Mr. Harry Plaza, P.E., of NASA's Environmental Assurance Branch is the Remediation Project Manager for John F. Kennedy Space Center. The Tetra Tech Program Manager is Mr. Mark Speranza, P.E., and the Tetra Tech Project Manager is Robert Simcik, P.E.

The Coastal Hazard Wheel system for coastal multi-hazard assessment & management in a changing climate

DEFF Research Database (Denmark)

Appelquist, Lars Rosendahl; Halsnæs, Kirsten

2015-01-01

This paper presents the complete Coastal Hazard Wheel (CHW) system, developed for multi-hazard-assessment and multi-hazard-management of coastal areas worldwide under a changing climate. The system is designed as a low-tech tool that can be used in areas with limited data availability...... screening and management. The system is developed to assess the main coastal hazards in a single process and covers the hazards of ecosystem disruption, gradual inundation, salt water intrusion, erosion and flooding. The system was initially presented in 2012 and based on a range of test......-applications and feedback from coastal experts, the system has been further refined and developed into a complete hazard management tool. This paper therefore covers the coastal classification system used by the CHW, a standardized assessment procedure for implementation of multi-hazard-assessments, technical guidance...

Disposal of hazardous wastes

International Nuclear Information System (INIS)

Barnhart, B.J.

1978-01-01

The Fifth Life Sciences Symposium entitled Hazardous Solid Wastes and Their Disposal on October 12 through 14, 1977 was summarized. The topic was the passage of the National Resources Conservation and Recovery Act of 1976 will force some type of action on all hazardous solid wastes. Some major points covered were: the formulation of a definition of a hazardous solid waste, assessment of long-term risk, list of specific materials or general criteria to specify the wastes of concern, Bioethics, sources of hazardous waste, industrial and agricultural wastes, coal wastes, radioactive wastes, and disposal of wastes

Offsite transportation hazards assessment

International Nuclear Information System (INIS)

Burnside, M.E.

1997-01-01

This report documents the emergency preparedness Hazards Assessment for the offsite transportation of hazardous material from the Hanford Site. The assessment is required by the US Department of Energy (DOE) Order 151.1. Offsite transportation accidents are categorized using the DOE system to assist communication within the DOE and assure that appropriate assistance is provided to the people in charge at the scene. The assistance will initially include information about the load and the potential hazards. Local authorities will use the information to protect the public following a transportation accident. This Hazards Assessment will focus on the material being transported from the Hanford Site. Shipments coming to Hanford are the responsibility of the shipper and the carrier and, therefore, are not included in this Hazards Assessment, unless the DOE elects to be the shipper of record

Radiological hazards of alpha-contaminated waste

International Nuclear Information System (INIS)

Rodgers, J.C.

1982-01-01

The radiological hazards of alpha-contaminated wastes are discussed in this overview in terms of two components of hazard: radiobiological hazard, and radioecological hazard. Radiobiological hazard refers to human uptake of alpha-emitters by inhalation and ingestion, and the resultant dose to critical organs of the body. Radioecological hazard refers to the processes of release from buried wastes, transport in the environment, and translocation to man through the food chain. Besides detailing the sources and magnitude of hazards, this brief review identifies the uncertainties in their estimation, and implications for the regulatory process

Hazards from aircraft

International Nuclear Information System (INIS)

Grund, J.E.; Hornyik, K.

1975-01-01

The siting of nuclear power plants has created innumerable environmental concerns. Among the effects of the ''man-made environment'' one of increasing importance in recent nuclear plant siting hazards analysis has been the concern about aircraft hazards to the nuclear plant. These hazards are of concern because of the possibility that an aircraft may have a malfunction and crash either near the plant or directly into it. Such a crash could be postulated to result, because of missile and/or fire effects, in radioactive releases which would endanger the public health and safety. The majority of studies related to hazards from air traffic have been concerned with the determination of the probability associated with an aircraft striking vulnerable portions of a given plant. Other studies have focused on the structural response to such a strike. This work focuses on the problem of strike probability. 13 references

49 CFR 172.317 - KEEP AWAY FROM HEAT handling mark.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false KEEP AWAY FROM HEAT handling mark. 172.317 Section... REQUIREMENTS, AND SECURITY PLANS Marking § 172.317 KEEP AWAY FROM HEAT handling mark. (a) General. For... of Division 5.2 must be marked with the KEEP AWAY FROM HEAT handling mark specified in this section...

Exploring the effects of driving experience on hazard awareness and risk perception via real-time hazard identification, hazard classification, and rating tasks.

Science.gov (United States)

Borowsky, Avinoam; Oron-Gilad, Tal

2013-10-01

This study investigated the effects of driving experience on hazard awareness and risk perception skills. These topics have previously been investigated separately, yet a novel approach is suggested where hazard awareness and risk perception are examined concurrently. Young, newly qualified drivers, experienced drivers, and a group of commercial drivers, namely, taxi drivers performed three consecutive tasks: (1) observed 10 short movies of real-world driving situations and were asked to press a button each time they identified a hazardous situation; (2) observed one of three possible sub-sets of 8 movies (out of the 10 they have seen earlier) for the second time, and were asked to categorize them into an arbitrary number of clusters according to the similarity in their hazardous situation; and (3) observed the same sub-set for a third time and following each movie were asked to rate its level of hazardousness. The first task is considered a real-time identification task while the other two are performed using hindsight. During it participants' eye movements were recorded. Results showed that taxi drivers were more sensitive to hidden hazards than the other driver groups and that young-novices were the least sensitive. Young-novice drivers also relied heavily on materialized hazards in their categorization structure. In addition, it emerged that risk perception was derived from two major components: the likelihood of a crash and the severity of its outcome. Yet, the outcome was rarely considered under time pressure (i.e., in real-time hazard identification tasks). Using hindsight, when drivers were provided with the opportunity to rate the movies' hazardousness more freely (rating task) they considered both components. Otherwise, in the categorization task, they usually chose the severity of the crash outcome as their dominant criterion. Theoretical and practical implications are discussed. Copyright © 2013 Elsevier Ltd. All rights reserved.

Probabilistic Tsunami Hazard Analysis

Science.gov (United States)

Thio, H. K.; Ichinose, G. A.; Somerville, P. G.; Polet, J.

2006-12-01

The recent tsunami disaster caused by the 2004 Sumatra-Andaman earthquake has focused our attention to the hazard posed by large earthquakes that occur under water, in particular subduction zone earthquakes, and the tsunamis that they generate. Even though these kinds of events are rare, the very large loss of life and material destruction caused by this earthquake warrant a significant effort towards the mitigation of the tsunami hazard. For ground motion hazard, Probabilistic Seismic Hazard Analysis (PSHA) has become a standard practice in the evaluation and mitigation of seismic hazard to populations in particular with respect to structures, infrastructure and lifelines. Its ability to condense the complexities and variability of seismic activity into a manageable set of parameters greatly facilitates the design of effective seismic resistant buildings but also the planning of infrastructure projects. Probabilistic Tsunami Hazard Analysis (PTHA) achieves the same goal for hazards posed by tsunami. There are great advantages of implementing such a method to evaluate the total risk (seismic and tsunami) to coastal communities. The method that we have developed is based on the traditional PSHA and therefore completely consistent with standard seismic practice. Because of the strong dependence of tsunami wave heights on bathymetry, we use a full waveform tsunami waveform computation in lieu of attenuation relations that are common in PSHA. By pre-computing and storing the tsunami waveforms at points along the coast generated for sets of subfaults that comprise larger earthquake faults, we can efficiently synthesize tsunami waveforms for any slip distribution on those faults by summing the individual subfault tsunami waveforms (weighted by their slip). This efficiency make it feasible to use Green's function summation in lieu of attenuation relations to provide very accurate estimates of tsunami height for probabilistic calculations, where one typically computes

Flood hazards for nuclear power plants

International Nuclear Information System (INIS)

Yen, B.C.

1988-01-01

Flooding hazards for nuclear power plants may be caused by various external geophysical events. In this paper the hydrologic hazards from flash floods, river floods and heavy rain at the plant site are considered. Depending on the mode of analysis, two types of hazard evaluation are identified: 1) design hazard which is the probability of flooding over an expected service period, and 2) operational hazard which deals with real-time forecasting of the probability of flooding of an incoming event. Hazard evaluation techniques using flood frequency analysis can only be used for type 1) design hazard. Evaluation techniques using rainfall-runoff simulation or multi-station correlation can be used for both types of hazard prediction. (orig.)

Mark Raidpere portreefotod Kielis

Index Scriptorium Estoniae

1999-01-01

Kieli Linnagaleriis avatud 2. Ars Baltica fototriennaalil 'Can You Hear Me?' esindab Eestit Mark Raidpere seeriaga 'Portreed 1998'. Näituse Eesti-poolne kuraator Anu Liivak, kataloogiteksti kirjutas Anders Härm. Tuntumaid osalejaid triennaalil Wolfgang Tillmans

Mark 1 Test Facility

Data.gov (United States)

Federal Laboratory Consortium — The Mark I Test Facility is a state-of-the-art space environment simulation test chamber for full-scale space systems testing. A $1.5M dollar upgrade in fiscal year...

Mark Raidpere näitused Pariisis ja Napolis / Mark Raidpere ; interv. Harry Liivrand

Index Scriptorium Estoniae

Raidpere, Mark

2008-01-01

Mark Raidpere videod "Vekovka", "Dedication / Pühendus", "Majestoso Mystico" näitusel Pariisis Michel Reini galeriis. Osaleb koos saksa fotograafi Sven Johnega näitusel Napolis. Kreekas Thessalonikis valminud filmist "1:1:1"

Mark retention of calcein in Cisco and Bloater

Science.gov (United States)

Chalupnicki, Marc A.; Mackey, Gregg; Nash, Kendra; Chiavelli, Richard; Johnson, James H.; Kehler, Thomas; Ringler, Neil H.

2016-01-01

Since 2012, a multi-agency initiative to restore these native forage species has been under way. Evaluating the restoration success of Cisco Coregonus artedi and Bloater C. hoyi in Lake Ontario waters requires methods to identify stocked fish. However, juvenile Cisco and Bloater are fragile; thus, mass marking techniques that reduce the handling of individual fish are required and have not previously been evaluated. In 2014–2015 we evaluated the usefulness of calcein (SE-MARK) as a marker on bony structures, including the otolith. Juvenile Bloater and Cisco (14, 100, 128 d old) were immersed in a calcein bath at 5,000 mg/L of water for 4 min to apply the chemical marker. Observations of the marking retention were evaluated 8 d following the treatment. All fish immersed in calcein had strong brilliant marks (rating scale 3) on all bony structures including scales, fin rays, jaw bones, and vertebrate. The otolith was the only hard structure that did not show a brilliant marking due to the opaque nature of the structure. Our results suggest that calcein produces a strong discernable mark on hard bony structures of Cisco and Bloater; however, long-term retention needs further study.

Geomorphological hazards in Swat valley, Pakistan

International Nuclear Information System (INIS)

Usman, A.

1999-01-01

This study attempts to describe, interpret and analyze, in depth, the varied geomorphological hazards and their impacts prevailing in the swat valley locate in the northern hilly and mountainous regions of Pakistan. The hills and mountains re zones of high geomorphological activity with rapid rates of weathering, active tectonic activities, abundant precipitation, rapid runoff and heavy sediment transport. Due to the varied topography, lithology, steep slope, erodible soil, heavy winter snowfall and intensive rainfall in the spring and summer seasons, several kinds of geomorphological hazards, such as geomorphic gravitational hazards, Fluvial hazards, Glacial hazards, Geo tectonic hazards, are occurring frequently in swat valley. Amongst them, geomorphic gravitational hazards, such as rock fall rock slide, debris slide mud flow avalanches, are major hazards in mountains and hills while fluvial hazards and sedimentation are mainly confined to the alluvial plain and lowlands of the valley. The Getechtonic hazards, on the other hand, have wide spread distribution in the valley the magnitude and occurrence of each king of hazard is thus, varied according to intensity of process and physical geographic environment. This paper discusses the type distribution and damage due to the various geomorphological hazards and their reduction treatments. The study would to be of particular importance and interest to both natural and social scientists, as well as planner, environmentalists and decision-makers for successful developmental interventions in the region. (author)

Welding hazards

International Nuclear Information System (INIS)

Khan, M.A.

1992-01-01

Welding technology is advancing rapidly in the developed countries and has converted into a science. Welding involving the use of electricity include resistance welding. Welding shops are opened in residential area, which was causing safety hazards, particularly the teenagers and children who eagerly see the welding arc with their naked eyes. There are radiation hazards from ultra violet rays which irritate the skin, eye irritation. Welding arc light of such intensity could damage the eyes. (Orig./A.B.)

Relative consequences of transporting hazardous materials

International Nuclear Information System (INIS)

Fullwood, R.R.; Rhyne, W.R.; Simmons, J.A.; Reese, R.T.

1980-01-01

The objective of this paper is to discuss methods under study at Transportation Technology Center to develop a perspective on how technical measures of hazard and risk relate to perception of hazards, harm, and risks associated with transporting hazardous materials. This paper is concerned with two major aspects of the relative hazards problem. The first aspect is the analyses of the possible effects associated with exposure to hazardous materials as contained in the following two parts: outlines of possible problems and controversies that could be encountered in the evaluation and comparisons of hazards and risks; and description of the various measures of harm (hazards or dangers) and subsequent comparisons thereof. The second aspect of this paper leads into a presentation of the results of a study which had the following purposes: to develop analytical techniques for a consistent treatment of the phenomenology of the consequences of a release of hazardous materials; to reduce the number of variables in the consequence analyses by development of transportation accident scenarios which have the same meteorological conditions, demography, traffic and population densities, geographical features and other appropriate conditions and to develop consistent methods for presenting the results of studies and analyses that describe the phenomenology and compare hazards. The results of the study are intended to provide a bridge between analytical certainty and perception of the hazards involved. Understanding the differences in perception of hazards resulting from transport of various hazardous materials is fraught with difficulties in isolating the qualitative and quantitative features of the problem. By relating the quantitative impacts of material hazards under identical conditions, it is hoped that the perceived differences in material hazards can be delineated and evaluated

Detection and recognition of road markings in panoramic images

Science.gov (United States)

Li, Cheng; Creusen, Ivo; Hazelhoff, Lykele; de With, Peter H. N.

2015-03-01

Detection of road lane markings is attractive for practical applications such as advanced driver assistance systems and road maintenance. This paper proposes a system to detect and recognize road lane markings in panoramic images. The system can be divided into four stages. First, an inverse perspective mapping is applied to the original panoramic image to generate a top-view road view, in which the potential road markings are segmented based on their intensity difference compared to the surrounding pixels. Second, a feature vector of each potential road marking segment is extracted by calculating the Euclidean distance between the center and the boundary at regular angular steps. Third, the shape of each segment is classified using a Support Vector Machine (SVM). Finally, by modeling the lane markings, previous falsely detected segments can be rejected based on their orientation and position relative to the lane markings. Our experiments show that the system is promising and is capable of recognizing 93%, 95% and 91% of striped line segments, blocks and arrows respectively, as well as 94% of the lane markings.

Seismic hazard assessment: Issues and alternatives

Science.gov (United States)

Wang, Z.

2011-01-01

Seismic hazard and risk are two very important concepts in engineering design and other policy considerations. Although seismic hazard and risk have often been used inter-changeably, they are fundamentally different. Furthermore, seismic risk is more important in engineering design and other policy considerations. Seismic hazard assessment is an effort by earth scientists to quantify seismic hazard and its associated uncertainty in time and space and to provide seismic hazard estimates for seismic risk assessment and other applications. Although seismic hazard assessment is more a scientific issue, it deserves special attention because of its significant implication to society. Two approaches, probabilistic seismic hazard analysis (PSHA) and deterministic seismic hazard analysis (DSHA), are commonly used for seismic hazard assessment. Although PSHA has been pro-claimed as the best approach for seismic hazard assessment, it is scientifically flawed (i.e., the physics and mathematics that PSHA is based on are not valid). Use of PSHA could lead to either unsafe or overly conservative engineering design or public policy, each of which has dire consequences to society. On the other hand, DSHA is a viable approach for seismic hazard assessment even though it has been labeled as unreliable. The biggest drawback of DSHA is that the temporal characteristics (i.e., earthquake frequency of occurrence and the associated uncertainty) are often neglected. An alternative, seismic hazard analysis (SHA), utilizes earthquake science and statistics directly and provides a seismic hazard estimate that can be readily used for seismic risk assessment and other applications. ?? 2010 Springer Basel AG.

EcoMark 2.0

DEFF Research Database (Denmark)

Guo, Chenjuan; Yang, Bin; Andersen, Ove

2015-01-01

Eco-routing is a simple yet effective approach to substantially reducing the environmental impact, e.g., fuel consumption and greenhouse gas (GHG) emissions, of vehicular transportation. Eco-routing relies on the ability to reliably quantify the environmental impact of vehicles as they travel...... in a spatial network. The procedure of quantifying such vehicular impact for road segments of a spatial network is called eco-weight assignment. EcoMark 2.0 proposes a general framework for eco-weight assignment to enable eco-routing. It studies the abilities of six instantaneous and five aggregated models......, and experiments for assessing the utility of the impact models in assigning eco-weights. The application of EcoMark 2.0 indicates that the instantaneous model EMIT and the aggregated model SIDRA-Running are suitable for assigning eco-weights under varying circumstances. In contrast, other instantaneous models...

Interview with Mark Watson

Directory of Open Access Journals (Sweden)

Katy Shaw

2016-04-01

Full Text Available Mark Watson is a British comedian and novelist. His five novels to date – 'Bullet Points' (2004, 'A Light-Hearted Look At Murder' (2007, 'Eleven' (2010, 'The Knot' (2012 and 'Hotel Alpha' (2014 – explore human relationships and communities in contemporary society. His latest novel Hotel Alpha tells the story of an extraordinary hotel in London and two mysterious disappearances that raise questions no one seems willing to answer. External to the novel, readers can also discover more about the hotel and its inhabitants in one hundred extra stories that expand the world of the novel and can be found at http://www.hotelalphastories.com. In conversation here with Dr Katy Shaw, Mark offers some reflections on his writing process, the field of contemporary literature, and the vitality of the novel form in the twenty-first century.

Recognition in context: Implications for trade mark law.

Science.gov (United States)

Humphreys, Michael S; McFarlane, Kimberley A; Burt, Jennifer S; Kelly, Sarah J; Weatherall, Kimberlee G; Burrell, Robert G

2017-10-01

Context effects in recognition have played a major role in evaluating theories of recognition. Understanding how context impacts recognition is also important for making sound trade mark law. Consumers attempting to discriminate between the brand they are looking for and a look-alike product often have to differentiate products which share a great deal of common context: positioning on the supermarket shelf, the type of store, aspects of the packaging, or brand claims. Trade mark and related laws aim to protect brands and reduce consumer confusion, but courts assessing allegations of trade mark infringement often lack careful empirical evidence concerning the impact of brand and context similarity, and, in the absence of such evidence, make assumptions about how consumers respond to brands that downplay the importance of context and focus on the similarity of registered marks. The experiments reported in this paper aimed to test certain common assumptions in trade mark law, providing evidence that shared context can cause mistakes even where brand similarity is low.

21 CFR 123.6 - Hazard analysis and Hazard Analysis Critical Control Point (HACCP) plan.

Science.gov (United States)

2010-04-01

... Control Point (HACCP) plan. 123.6 Section 123.6 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF... Provisions § 123.6 Hazard analysis and Hazard Analysis Critical Control Point (HACCP) plan. (a) Hazard... fish or fishery product being processed in the absence of those controls. (b) The HACCP plan. Every...

Trade Mark Cluttering: An Exploratory Report Commissioned by UKIPO

OpenAIRE

von Graevenitz, Georg; Greenhalgh, Christine; Helmers, Christian; Schautschick, Philipp

2012-01-01

This report explores the problem of “cluttering” of trade mark registers. The report consists of two parts: the first presents a conceptual discussion of “cluttering” of trade mark registers. The second part provides an exploratory empirical analysis of trade mark applications at the UK Intellectual Property Office (UKIPO) and the European trade mark office (OHIM). This part contains results of a descriptive and an econometric analysis. According to our definition, cluttering arises where fir...

Resilience to Interacting multi-natural hazards

Science.gov (United States)

Zhuo, Lu; Han, Dawei

2016-04-01

Conventional analyses of hazard assessment tend to focus on individual hazards in isolation. However, many parts of the world are usually affected by multiple natural hazards with the potential for interacting relationships. The understanding of such interactions, their impacts and the related uncertainties, are an important and topical area of research. Interacting multi-hazards may appear in different forms, including 1) CASCADING HAZARDS (a primary hazard triggering one or more secondary hazards such as an earthquake triggering landslides which may block river channels with dammed lakes and ensued floods), 2) CONCURRING HAZARDS (two or more primary hazards coinciding to trigger or exacerbate secondary hazards such as an earthquake and a rainfall event simultaneously creating landslides), and 3) ALTERING HAZARDS (a primary hazard increasing the probability of a secondary hazard occurring such as major earthquakes disturbing soil/rock materials by violent ground shaking which alter the regional patterns of landslides and debris flows in the subsequent years to come). All three types of interacting multi-hazards may occur in natural hazard prone regions, so it is important that research on hazard resilience should cover all of them. In the past decades, great progresses have been made in tackling disaster risk around the world. However, there are still many challenging issues to be solved, and the disasters over recent years have clearly demonstrated the inadequate resilience in our highly interconnected and interdependent systems. We have identified the following weaknesses and knowledge gaps in the current disaster risk management: 1) although our understanding in individual hazards has been greatly improved, there is a lack of sound knowledge about mechanisms and processes of interacting multi-hazards. Therefore, the resultant multi-hazard risk is often significantly underestimated with severe consequences. It is also poorly understood about the spatial and

32 CFR 2400.16 - Derivative classification markings.

Science.gov (United States)

2010-07-01

... SECURITY PROGRAM Derivative Classification § 2400.16 Derivative classification markings. (a) Documents... 32 National Defense 6 2010-07-01 2010-07-01 false Derivative classification markings. 2400.16..., as described in § 2400.12 of this part, the information may not be used as a basis for derivative...

Multiplexing clonality: combining RGB marking and genetic barcoding

Science.gov (United States)

Cornils, Kerstin; Thielecke, Lars; Hüser, Svenja; Forgber, Michael; Thomaschewski, Michael; Kleist, Nadja; Hussein, Kais; Riecken, Kristoffer; Volz, Tassilo; Gerdes, Sebastian; Glauche, Ingmar; Dahl, Andreas; Dandri, Maura; Roeder, Ingo; Fehse, Boris

2014-01-01

RGB marking and DNA barcoding are two cutting-edge technologies in the field of clonal cell marking. To combine the virtues of both approaches, we equipped LeGO vectors encoding red, green or blue fluorescent proteins with complex DNA barcodes carrying color-specific signatures. For these vectors, we generated highly complex plasmid libraries that were used for the production of barcoded lentiviral vector particles. In proof-of-principle experiments, we used barcoded vectors for RGB marking of cell lines and primary murine hepatocytes. We applied single-cell polymerase chain reaction to decipher barcode signatures of individual RGB-marked cells expressing defined color hues. This enabled us to prove clonal identity of cells with one and the same RGB color. Also, we made use of barcoded vectors to investigate clonal development of leukemia induced by ectopic oncogene expression in murine hematopoietic cells. In conclusion, by combining RGB marking and DNA barcoding, we have established a novel technique for the unambiguous genetic marking of individual cells in the context of normal regeneration as well as malignant outgrowth. Moreover, the introduction of color-specific signatures in barcodes will facilitate studies on the impact of different variables (e.g. vector type, transgenes, culture conditions) in the context of competitive repopulation studies. PMID:24476916

Hazardous materials and waste management a guide for the professional hazards manager

CERN Document Server

Cheremisinoff, Nicholas P

1995-01-01

The management of hazardous materials and industrial wastes is complex, requiring a high degree of knowledge over very broad technical and legal subject areas. Hazardous wastes and materials are diverse, with compositions and properties that not only vary significantly between industries, but within industries, and indeed within the complexity of single facilities. Proper management not only requires an understanding of the numerous and complex regulations governing hazardous materials and waste streams, but an understanding and knowledge of the treatment, post-treatment, and waste minimizatio

78 FR 58604 - Safety Advisory: Unauthorized Marking of Compressed Gas Cylinders

Science.gov (United States)

2013-09-24

... DEPARTMENT OF TRANSPORTATION Pipeline and Hazardous Materials Safety Administration [Docket No... AGENCY: Pipeline and Hazardous Materials Safety Administration (PHMSA), DOT. ACTION: Safety Advisory... Investigator, Eastern Region, Office of Hazardous Materials Safety, Pipeline and Hazardous Materials Safety...

Marking for Structure using Boolean Feedback | Louw | Journal for ...

African Journals Online (AJOL)

This paper presents evidence that marking student texts with well considered checklists is more effective than marking by hand. An experiment conducted on first-year students illustrated that the checklists developed to mark introductions, conclusions and paragraphs yielded better revision results than handwritten ...

Tooth-marked small theropod bone: an extremely rare trace

DEFF Research Database (Denmark)

Jacobsen, Aase Roland

2001-01-01

Tooth-marked dinosaur bones provide insight into feeding behaviours and biting strategies of theropod dinosaurs. The majority of theropod tooth marks reported to date have been found on herbivorous dinosaur bones, although some tyrannosaurid bones with tooth marks have also been reported. In 1988...

Hazards in the chemical laboratory

International Nuclear Information System (INIS)

Bretherick, L.

1987-01-01

The contents of this book are: Preface; Introduction; Health and Safety at Work Act 1974; Safety Planning and Management; Fire Protection; Reactive Chemical Hazards; Chemical Hazards and Toxicology; Health Care and First Aid; Hazardous Chemicals; Precautions against Radiations; and An American View

7 CFR 920.303 - Container marking regulations.

Science.gov (United States)

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Container marking regulations. 920.303 Section 920.303... Miscellaneous Provisions § 920.303 Container marking regulations. No handler shall ship any kiwifruit except in accordance with the following terms and conditions: (a) Each package or container of kiwifruit shall bear on...

St. Louis area earthquake hazards mapping project; seismic and liquefaction hazard maps

Science.gov (United States)

Cramer, Chris H.; Bauer, Robert A.; Chung, Jae-won; Rogers, David; Pierce, Larry; Voigt, Vicki; Mitchell, Brad; Gaunt, David; Williams, Robert; Hoffman, David; Hempen, Gregory L.; Steckel, Phyllis; Boyd, Oliver; Watkins, Connor M.; Tucker, Kathleen; McCallister, Natasha

2016-01-01

We present probabilistic and deterministic seismic and liquefaction hazard maps for the densely populated St. Louis metropolitan area that account for the expected effects of surficial geology on earthquake ground shaking. Hazard calculations were based on a map grid of 0.005°, or about every 500 m, and are thus higher in resolution than any earlier studies. To estimate ground motions at the surface of the model (e.g., site amplification), we used a new detailed near‐surface shear‐wave velocity model in a 1D equivalent‐linear response analysis. When compared with the 2014 U.S. Geological Survey (USGS) National Seismic Hazard Model, which uses a uniform firm‐rock‐site condition, the new probabilistic seismic‐hazard estimates document much more variability. Hazard levels for upland sites (consisting of bedrock and weathered bedrock overlain by loess‐covered till and drift deposits), show up to twice the ground‐motion values for peak ground acceleration (PGA), and similar ground‐motion values for 1.0 s spectral acceleration (SA). Probabilistic ground‐motion levels for lowland alluvial floodplain sites (generally the 20–40‐m‐thick modern Mississippi and Missouri River floodplain deposits overlying bedrock) exhibit up to twice the ground‐motion levels for PGA, and up to three times the ground‐motion levels for 1.0 s SA. Liquefaction probability curves were developed from available standard penetration test data assuming typical lowland and upland water table levels. A simplified liquefaction hazard map was created from the 5%‐in‐50‐year probabilistic ground‐shaking model. The liquefaction hazard ranges from low (60% of area expected to liquefy) in the lowlands. Because many transportation routes, power and gas transmission lines, and population centers exist in or on the highly susceptible lowland alluvium, these areas in the St. Louis region are at significant potential risk from seismically induced liquefaction and associated

Hazardous solvent substitution

International Nuclear Information System (INIS)

Twitchell, K.E.

1995-01-01

This article is an overview of efforts at INEL to reduce the generation of hazardous wastes through the elimination of hazardous solvents. To aid in their efforts, a number of databases have been developed and will become a part of an Integrated Solvent Substitution Data System. This latter data system will be accessible through Internet

27 CFR 19.612 - Authorized abbreviations to identify marks.

Science.gov (United States)

2010-04-01

... T Tax Determined TD Wine Spirits Addition WSA (Sec. 201, Pub. L. 85-859, 72 Stat. 1360, as amended... TAX AND TRADE BUREAU, DEPARTMENT OF THE TREASURY LIQUORS DISTILLED SPIRITS PLANTS Containers and Marks... to identify certain marks: Mark Abbreviation Completely Denatured Alcohol CDA Distilled Spirits...

Modified hazard ranking system for sites with mixed radioactive and hazardous wastes. User manual

International Nuclear Information System (INIS)

Hawley, K.A.; Peloquin, R.A.; Stenner, R.D.

1986-04-01

This document describes both the original Hazard Ranking System and the modified Hazard Ranking System as they are to be used in evaluating the relative potential for uncontrolled hazardous substance facilities to cause human health or safety problems or ecological or environmental damage. Detailed instructions for using the mHRS/HRS computer code are provided, along with instructions for performing the calculations by hand. Uniform application of the ranking system will permit the DOE to identify those releases of hazardous substances that pose the greatest hazard to humans or the environment. However, the mHRS/HRS by itself cannot establish priorities for the allocation of funds for remedial action. The mHRS/HRS is a means for applying uniform technical judgment regarding the potential hazards presented by a facility relative to other facilities. It does not address the feasibility, desirability, or degree of cleanup required. Neither does it deal with the readiness or ability of a state to carry out such remedial action, as may be indicated, or to meet other conditions prescribed in CERCLA. 13 refs., 13 figs., 27 tabs

Modified hazard ranking system for sites with mixed radioactive and hazardous wastes. User manual.

Energy Technology Data Exchange (ETDEWEB)

Hawley, K.A.; Peloquin, R.A.; Stenner, R.D.

1986-04-01

This document describes both the original Hazard Ranking System and the modified Hazard Ranking System as they are to be used in evaluating the relative potential for uncontrolled hazardous substance facilities to cause human health or safety problems or ecological or environmental damage. Detailed instructions for using the mHRS/HRS computer code are provided, along with instructions for performing the calculations by hand. Uniform application of the ranking system will permit the DOE to identify those releases of hazardous substances that pose the greatest hazard to humans or the environment. However, the mHRS/HRS by itself cannot establish priorities for the allocation of funds for remedial action. The mHRS/HRS is a means for applying uniform technical judgment regarding the potential hazards presented by a facility relative to other facilities. It does not address the feasibility, desirability, or degree of cleanup required. Neither does it deal with the readiness or ability of a state to carry out such remedial action, as may be indicated, or to meet other conditions prescribed in CERCLA. 13 refs., 13 figs., 27 tabs.

Hazardous solvent substitution

International Nuclear Information System (INIS)

Twitchell, K.E.

1995-01-01

Eliminating hazardous solvents is good for the environment, worker safety, and the bottom line. However, even though we are motivated to find replacements, the big question is 'What can we use as replacements for hazardous solvents?'You, too, can find replacements for your hazardous solvents. All you have to do is search for them. Search through the vendor literature of hundreds of companies with thousands of products. Ponder the associated material safety data sheets, assuming of course that you can obtain them and, having obtained them, that you can read them. You will want to search the trade magazines and other sources for product reviews. You will want to talk to users about how well the product actually works. You may also want to check US Environmental Protection Agency (EPA) and other government reports for toxicity and other safety information. And, of course, you will want to compare the product's constituent chemicals with the many hazardous constituency lists to ensure the safe and legal use of the product in your workplace

The national hydrologic bench-mark network

Science.gov (United States)

Cobb, Ernest D.; Biesecker, J.E.

1971-01-01

The United States is undergoing a dramatic growth of population and demands on its natural resources. The effects are widespread and often produce significant alterations of the environment. The hydrologic bench-mark network was established to provide data on stream basins which are little affected by these changes. The network is made up of selected stream basins which are not expected to be significantly altered by man. Data obtained from these basins can be used to document natural changes in hydrologic characteristics with time, to provide a better understanding of the hydrologic structure of natural basins, and to provide a comparative base for studying the effects of man on the hydrologic environment. There are 57 bench-mark basins in 37 States. These basins are in areas having a wide variety of climate and topography. The bench-mark basins and the types of data collected in the basins are described.

Radon and its hazards

International Nuclear Information System (INIS)

Chang Guilan

2002-01-01

The author describes basic physical and chemical properties of radon and the emanation, introduces methods of radon measurement, expounds the hazards of non-mine radon accumulation to the health of human being and the protection, as well as the history how the human being recognizes the hazards of radon through the specific data and examples, and finally proposes protecting measures to avoid the hazards of radon to the health of human being, and to do ecologic evaluation of environments

Industrial hazard and safety handbook

CERN Document Server

King, Ralph W

1979-01-01

Industrial Hazard and Safety Handbook (Revised Impression) describes and exposes the main hazards found in industry, with emphasis on how these hazards arise, are ignored, are identified, are eliminated, or are controlled. These hazard conditions can be due to human stresses (for example, insomnia), unsatisfactory working environments, as well as secret industrial processes. The book reviews the cost of accidents, human factors, inspections, insurance, legal aspects, planning for major emergencies, organization, and safety measures. The text discusses regulations, codes of practice, site layou

46 CFR 160.077-31 - PFD Marking.

Science.gov (United States)

2010-10-01

... Marking. (a) General. Each hybrid PFD must be marked with the applicable information required by this... text of special purpose or limitation and vessel(s) or vessel type(s), noted on approval certificate... and be presented in the exact order shown: Type [II, III, or V, as applicable] PFD [See paragraph (k...

Global Landslide Hazard Distribution

Data.gov (United States)

National Aeronautics and Space Administration — Global Landslide Hazard Distribution is a 2.5 minute grid of global landslide and snow avalanche hazards based upon work of the Norwegian Geotechnical Institute...

9 CFR 590.418 - Supervision of marking and packaging.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Supervision of marking and packaging...) Identifying and Marking Product § 590.418 Supervision of marking and packaging. (a) Evidence of label approval... has on file evidence that such official identification or packaging material bearing such official...

Lane marking detection based on waveform analysis and CNN

Science.gov (United States)

Ye, Yang Yang; Chen, Hou Jin; Hao, Xiao Li

2017-06-01

Lane markings detection is a very important part of the ADAS to avoid traffic accidents. In order to obtain accurate lane markings, in this work, a novel and efficient algorithm is proposed, which analyses the waveform generated from the road image after inverse perspective mapping (IPM). The algorithm includes two main stages: the first stage uses an image preprocessing including a CNN to reduce the background and enhance the lane markings. The second stage obtains the waveform of the road image and analyzes the waveform to get lanes. The contribution of this work is that we introduce local and global features of the waveform to detect the lane markings. The results indicate the proposed method is robust in detecting and fitting the lane markings.

Statistical methods for the forensic analysis of striated tool marks

Energy Technology Data Exchange (ETDEWEB)

Hoeksema, Amy Beth [Iowa State Univ., Ames, IA (United States)

2013-01-01

In forensics, fingerprints can be used to uniquely identify suspects in a crime. Similarly, a tool mark left at a crime scene can be used to identify the tool that was used. However, the current practice of identifying matching tool marks involves visual inspection of marks by forensic experts which can be a very subjective process. As a result, declared matches are often successfully challenged in court, so law enforcement agencies are particularly interested in encouraging research in more objective approaches. Our analysis is based on comparisons of profilometry data, essentially depth contours of a tool mark surface taken along a linear path. In current practice, for stronger support of a match or non-match, multiple marks are made in the lab under the same conditions by the suspect tool. We propose the use of a likelihood ratio test to analyze the difference between a sample of comparisons of lab tool marks to a field tool mark, against a sample of comparisons of two lab tool marks. Chumbley et al. (2010) point out that the angle of incidence between the tool and the marked surface can have a substantial impact on the tool mark and on the effectiveness of both manual and algorithmic matching procedures. To better address this problem, we describe how the analysis can be enhanced to model the effect of tool angle and allow for angle estimation for a tool mark left at a crime scene. With sufficient development, such methods may lead to more defensible forensic analyses.

Natural Hazards, Second Edition

Science.gov (United States)

Rouhban, Badaoui

Natural disaster loss is on the rise, and the vulnerability of the human and physical environment to the violent forces of nature is increasing. In many parts of the world, disasters caused by natural hazards such as earthquakes, floods, landslides, drought, wildfires, intense windstorms, tsunami, and volcanic eruptions have caused the loss of human lives, injury, homelessness, and the destruction of economic and social infrastructure. Over the last few years, there has been an increase in the occurrence, severity, and intensity of disasters, culminating with the devastating tsunami of 26 December 2004 in South East Asia.Natural hazards are often unexpected or uncontrollable natural events of varying magnitude. Understanding their mechanisms and assessing their distribution in time and space are necessary for refining risk mitigation measures. This second edition of Natural Hazards, (following a first edition published in 1991 by Cambridge University Press), written by Edward Bryant, associate dean of science at Wollongong University, Australia, grapples with this crucial issue, aspects of hazard prediction, and other issues. The book presents a comprehensive analysis of different categories of hazards of climatic and geological origin.

Carbon Structure Hazard Control

Science.gov (United States)

Yoder, Tommy; Greene, Ben; Porter, Alan

2015-01-01

Carbon composite structures are widely used in virtually all advanced technology industries for a multitude of applications. The high strength-to-weight ratio and resistance to aggressive service environments make them highly desirable. Automotive, aerospace, and petroleum industries extensively use, and will continue to use, this enabling technology. As a result of this broad range of use, field and test personnel are increasingly exposed to hazards associated with these structures. No single published document exists to address the hazards and make recommendations for the hazard controls required for the different exposure possibilities from damaged structures including airborne fibers, fly, and dust. The potential for personnel exposure varies depending on the application or manipulation of the structure. The effect of exposure to carbon hazards is not limited to personnel, protection of electronics and mechanical equipment must be considered as well. The various exposure opportunities defined in this document include pre-manufacturing fly and dust, the cured structure, manufacturing/machining, post-event cleanup, and post-event test and/or evaluation. Hazard control is defined as it is applicable or applied for the specific exposure opportunity. The carbon exposure hazard includes fly, dust, fiber (cured/uncured), and matrix vapor/thermal decomposition products. By using the recommendations in this document, a high level of confidence can be assured for the protection of personnel and equipment.

UID...Leaving Its Mark on the Universe

Science.gov (United States)

Schramm, Harry F., Jr.

2008-01-01

Since 1975 bar codes on products at the retail counter have been accepted as the standard for entering product identity for price determination. Since the beginning of the 21 st century, the Data Matrix symbol has become accepted as the bar code format that is marked directly on a part, assembly or product that is durable enough to identify that item for its lifetime. NASA began the studies for direct part marking Data Matrix symbols on parts during the Return to Flight activities after the Challenger Accident. Over the 20 year period that has elapsed since Challenger, a mountain of studies, analyses and focused problem solutions developed by and for NASA have brought about world changing results. NASA Technical Standard 6002 and NASA Handbook 6003 for Direct Part Marking Data Matrix Symbols on Aerospace Parts have formed the basis for most other standards on part marking internationally. NASA and its commercial partners have developed numerous products and methods that addressed the difficulties of collecting part identification in aerospace operations. These products enabled the marking of Data Matrix symbols in virtually every situation and the reading of symbols at great distances, severe angles, under paint and in the dark without a light. Even unmarkable delicate parts now have a process to apply a chemical mixture, recently trademarked as Nanocodes, that can be converted to Data Matrix information through software. The accompanying intellectual property is protected by ten patents, several of which are licensed. Direct marking Data Matrix on NASA parts dramatically decreases data entry errors and the number of parts that go through their life cycle unmarked, two major threats to sound configuration management and flight safety. NASA is said to only have people and stuff with information connecting them. Data Matrix is one of the most significant improvements since Challenger to the safety and reliability of that connection.

UID....Now That's Gonna Leave A Mark

Science.gov (United States)

Schramm, Harry F., Jr.

2008-01-01

Since 1975 bar codes on products at the retail counter have been accepted as the standard for entering product identity for price determination. Since the beginning of the 21 st century, the Data Matrix symbol has become accepted as the bar code format that is marked directly on a part, assembly or product that is durable enough to identify that item for its lifetime. NASA began the studies for direct part marking Data Matrix symbols on parts during the Return to Flight activities after the Challenger Accident. Over the 20 year period that has elapsed since Challenger, a mountain of studies, analyses and focused problem solutions developed by and for NASA have brought about world changing results. NASA Technical Standard 6002 and NASA Handbook 6003 for Direct Part Marking Data Matrix Symbols on Aerospace Parts have formed the basis for most other standards on part marking internationally. NASA and its commercial partners have developed numerous products and methods that addressed the difficulties of collecting part identification in aerospace operations. These products enabled the marking of Data Matrix symbols in virtually every situation and the reading of symbols at great distances, severe angles, under paint and in the dark without a light. Even unmarkable delicate parts now have a process to apply a chemical mixture, recently trademarked as Nanocodes, that can be converted to Data Matrix information through software. The accompanying intellectual property is protected by ten patents, several of which are licensed. Direct marking Data Matrix on NASA parts dramatically decreases data entry errors and the number of parts that go through their life cycle unmarked, two major threats to sound configuration management and flight safety. NASA is said to only have people and stuff with information connecting them. Data Matrix is one of the most significant improvements since Challenger to the safety and reliability of that connection.

75 FR 73972 - Hazardous Waste Management System; Identification and Listing of Hazardous Waste; Removal of...

Science.gov (United States)

2010-11-30

... Waste Management System; Identification and Listing of Hazardous Waste; Removal of Direct Final.... Lists of Subjects in 40 CFR Part 261 Environmental Protection, Hazardous waste, Recycling, Reporting and... follows: PART 261--IDENTIFICATION AND LISTING OF HAZARDOUS WASTE 0 1. The authority citation for part 261...

Otolith marking of juvenile shortnose gar by immersion in oxytetracycline

Science.gov (United States)

Snow, Richard A.; Long, James M.

2017-01-01

Oxytetracycline (OTC) has been used to mark a variety of fish species at multiple developmental stages; however, there is little information on batch-marking Lepisosteidae. Juvenile Shortnose Gar Lepisosteus platostomus (53 ± 3 mm TL) were seined from an Oklahoma State University research pond and transported to the Oklahoma Fishery Research Lab. Juvenile Shortnose Gar were exposed to a range of OTC concentrations—0, 500, 600, and 700 mg/L—for 4, 5, or 6 h. Lapillus and sagitta otoliths were examined 14 d postexposure for mark presence and evaluation using fluorescent microscopy. Overall, 93.3% of otoliths exposed to OTC exhibited a mark. Concentration of OTC affected the mean mark quality, whereas duration and otolith type examined did not. However, as concentration increased, so did mortality, suggesting a balance is needed to achieve marking goals. Based on our findings, batch marking of Shortnose Gar can be successful at OTC concentrations from 500 to 700 mg/L for 4–6 h, although mark quality may vary and mortality rates increase at the higher concentrations and longer durations.

Hazardous waste: cleanup and prevention

Science.gov (United States)

Vandas, Stephen; Cronin, Nancy L.; Farrar, Frank; Serrano, Guillermo Eliezer Ávila; Yajimovich, Oscar Efraín González; Muñoz, Aurora R.; Rivera, María del C.

1996-01-01

Our lifestyles are supported by complex Industrial activities that produce many different chemicals and chemical wastes. The Industries that produce our clothing, cars, medicines, paper, food, fuels, steel, plastics, and electric components use and discard thousands of chemicals every year. At home we may use lawn chemicals, solvents, disinfectants, cleaners, and auto products to Improve our quality of life. A chemical that presents a threat or unreasonable risk to people or the environment Is a hazardous material. When a hazardous material can no longer be used, It becomes a hazardous waste. Hazardous wastes come from a variety of sources, from both present and past activities. Impacts to human health and the environment can result from Improper handling and disposal of hazardous waste.

SRL process hazards review manual

International Nuclear Information System (INIS)

1980-08-01

The principal objective of the Process Hazards Management Program is to provide a regular, systematic review of each process at the Savannah River Laboratory (SRL) to eliminate injuries and to minimize property damage resulting from process hazards of catastrophic potential. Management effort is directed, through the Du Pont Safety Program, toward those controls and practices that ensure this objective. The Process Hazards Management Program provides an additional dimension to further ensure the health and safety of employees and the public. Du Pont has concluded that an organized approach is essential to obtain an effective and efficient process hazards review. The intent of this manual is to provide guidance in creating such an organized approach to performing process hazards reviews on a continuing basis

Hydrothermal Liquefaction Treatment Hazard Analysis Report

Energy Technology Data Exchange (ETDEWEB)

Lowry, Peter P. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wagner, Katie A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2016-09-12

Hazard analyses were performed to evaluate the modular hydrothermal liquefaction treatment system. The hazard assessment process was performed in 2 stages. An initial assessment utilizing Hazard Identification and Preliminary Hazards Analysis (PHA) techniques identified areas with significant or unique hazards (process safety-related hazards) that fall outside of the normal operating envelope of PNNL and warranted additional analysis. The subsequent assessment was based on a qualitative What-If analysis. The analysis was augmented, as necessary, by additional quantitative analysis for scenarios involving a release of hazardous material or energy with the potential for affecting the public. The following selected hazardous scenarios received increased attention: •Scenarios involving a release of hazardous material or energy, controls were identified in the What-If analysis table that prevent the occurrence or mitigate the effects of the release. •Scenarios with significant consequences that could impact personnel outside the immediate operations area, quantitative analyses were performed to determine the potential magnitude of the scenario. The set of “critical controls” were identified for these scenarios (see Section 4) which prevent the occurrence or mitigate the effects of the release of events with significant consequences.

Hazardous Chemicals

Centers for Disease Control (CDC) Podcasts

2007-04-10

Chemicals are a part of our daily lives, providing many products and modern conveniences. With more than three decades of experience, The Centers for Disease Control and Prevention (CDC) has been in the forefront of efforts to protect and assess people's exposure to environmental and hazardous chemicals. This report provides information about hazardous chemicals and useful tips on how to protect you and your family from harmful exposure.  Created: 4/10/2007 by CDC National Center for Environmental Health.   Date Released: 4/13/2007.

Radio-marking and in vivo imagery of oligonucleotides

International Nuclear Information System (INIS)

Kuehnast, Bertrand

2000-01-01

This research thesis is part of activities aimed at the development of new molecules like oligonucleotides. Its first objective was the development and validation of a marking method with fluorine-18 of oligonucleotides for their in-vivo pharmacological assessment with positron emission tomography (PET). Further investigations addressed the use of iodine-125 for oligonucleotide marking purpose. This radio-marking, and in vivo and ex vivo imagery techniques are described, and their potential is highlighted for the pharmacological assessment of different oligonucleotides

Field manual for identifying and preserving high-water mark data

Science.gov (United States)

Feaster, Toby D.; Koenig, Todd A.

2017-09-26

This field manual provides general guidance for identifying and collecting high-water marks and is meant to be used by field personnel as a quick reference. The field manual describes purposes for collecting and documenting high-water marks along with the most common types of high-water marks. The manual provides a list of suggested field equipment, describes rules of thumb and best practices for finding high-water marks, and describes the importance of evaluating each high-water mark and assigning a numeric uncertainty value as part of the flagging process. The manual also includes an appendix of photographs of a variety of high-water marks obtained from various U.S. Geological Survey field investigations along with general comments about the logic for the assigned uncertainty values.

Transportation of Hazardous Evidentiary Material.

Energy Technology Data Exchange (ETDEWEB)

Osborn, Douglas.

2005-06-01

This document describes the specimen and transportation containers currently available for use with hazardous and infectious materials. A detailed comparison of advantages, disadvantages, and costs of the different technologies is included. Short- and long-term recommendations are also provided.3 DraftDraftDraftExecutive SummaryThe Federal Bureau of Investigation's Hazardous Materials Response Unit currently has hazardous material transport containers for shipping 1-quart paint cans and small amounts of contaminated forensic evidence, but the containers may not be able to maintain their integrity under accident conditions or for some types of hazardous materials. This report provides guidance and recommendations on the availability of packages for the safe and secure transport of evidence consisting of or contaminated with hazardous chemicals or infectious materials. Only non-bulk containers were considered because these are appropriate for transport on small aircraft. This report will addresses packaging and transportation concerns for Hazardous Classes 3, 4, 5, 6, 8, and 9 materials. If the evidence is known or suspected of belonging to one of these Hazardous Classes, it must be packaged in accordance with the provisions of 49 CFR Part 173. The anthrax scare of several years ago, and less well publicized incidents involving unknown and uncharacterized substances, has required that suspicious substances be sent to appropriate analytical laboratories for analysis and characterization. Transportation of potentially hazardous or infectious material to an appropriate analytical laboratory requires transport containers that maintain both the biological and chemical integrity of the substance in question. As a rule, only relatively small quantities will be available for analysis. Appropriate transportation packaging is needed that will maintain the integrity of the substance, will not allow biological alteration, will not react chemically with the substance being

Comparative Distributions of Hazard Modeling Analysis

Directory of Open Access Journals (Sweden)

Rana Abdul Wajid

2006-07-01

Full Text Available In this paper we present the comparison among the distributions used in hazard analysis. Simulation technique has been used to study the behavior of hazard distribution modules. The fundamentals of Hazard issues are discussed using failure criteria. We present the flexibility of the hazard modeling distribution that approaches to different distributions.

30 CFR 47.21 - Identifying hazardous chemicals.

Science.gov (United States)

2010-07-01

..., subpart Z, Toxic and Hazardous Substances. (4) American Conference of Governmental Industrial Hygienists... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Identifying hazardous chemicals. 47.21 Section... TRAINING HAZARD COMMUNICATION (HazCom) Hazard Determination § 47.21 Identifying hazardous chemicals. The...

Survival and reproduction of radio-marked adult spotted owls.

Science.gov (United States)

C.C. Foster; E.D. Forsman; E.C. Meslow; G.S. Miller; J.A. Reid; F.F. Wagner; A.B. Carey; J.B. Lint

1992-01-01

We compared survival, reproduction, and body mass of radio-marked and non radio-marked spotted owls (Strix occidentalis) to determine if backpack radios influenced reproduction or survival. In most study areas and years, there were no differences (P > 0.05) in survival of males and females or in survival of radio-marked versus banded owls. There...

76 FR 74709 - Hazardous Waste Management System; Identification and Listing of Hazardous Waste; Final Exclusion

Science.gov (United States)

2011-12-01

..., including any sludge, spill residue, ash, emission control dust, or leachate, remains a hazardous waste... water for use as a cleaning agent. The slop oil waste is thereby diluted and hazardous constituents are... separation sludges that are listed as hazardous wastes due to benzene, benzo(a)pyrene, chrysene, lead and...

75 FR 78918 - Hazardous Waste Management System; Identification and Listing of Hazardous Waste; Removal of...

Science.gov (United States)

2010-12-17

... and Community Right-to-Know Act FDA Food and Drug Administration HSWA Hazardous and Solid Waste...(f)), and hazardous substances (40 CFR 302.4) based solely upon the evidence that it is a potential... subsequently identified as hazardous wastes in Sec. 261.33(f) based solely on their potential for carcinogenic...

Modified Hazard Ranking System/Hazard Ranking System for sites with mixed radioactive and hazardous wastes: Software documentation

Energy Technology Data Exchange (ETDEWEB)

Stenner, R.D.; Peloquin, R.A.; Hawley, K.A.

1986-11-01

The mHRS/HRS software package was developed by the Pacific Northwest Laboratory (PNL) under contract with the Department of Energy (DOE) to provide a uniform method for DOE facilities to use in performing their Conservation Environmental Response Compensation and Liability Act (CERCLA) Phase I Modified Hazard Ranking System or Hazard Ranking System evaluations. The program is designed to remove the tedium and potential for error associated with the performing of hand calculations and the interpreting of information on tables and in reference books when performing an evaluation. The software package is designed to operate on a microcomputer (IBM PC, PC/XT, or PC/AT, or a compatible system) using either a dual floppy disk drive or a hard disk storage system. It is written in the dBASE III language and operates using the dBASE III system. Although the mHRS/HRS software package was developed for use at DOE facilities, it has direct applicability to the performing of CERCLA Phase I evaluations for any facility contaminated by hazardous waste. The software can perform evaluations using either the modified hazard ranking system methodology developed by DOE/PNL, the hazard ranking system methodology developed by EPA/MITRE Corp., or a combination of the two. This document is a companion manual to the mHRS/HRS user manual. It is intended for the programmer who must maintain the software package and for those interested in the computer implementation. This manual documents the system logic, computer programs, and data files that comprise the package. Hardware and software implementation requirements are discussed. In addition, hand calculations of three sample situations (problems) with associated computer runs used for the verification of program calculations are included.

Modified Hazard Ranking System/Hazard Ranking System for sites with mixed radioactive and hazardous wastes: Software documentation

International Nuclear Information System (INIS)

Stenner, R.D.; Peloquin, R.A.; Hawley, K.A.

1986-11-01

The mHRS/HRS software package was developed by the Pacific Northwest Laboratory (PNL) under contract with the Department of Energy (DOE) to provide a uniform method for DOE facilities to use in performing their Conservation Environmental Response Compensation and Liability Act (CERCLA) Phase I Modified Hazard Ranking System or Hazard Ranking System evaluations. The program is designed to remove the tedium and potential for error associated with the performing of hand calculations and the interpreting of information on tables and in reference books when performing an evaluation. The software package is designed to operate on a microcomputer (IBM PC, PC/XT, or PC/AT, or a compatible system) using either a dual floppy disk drive or a hard disk storage system. It is written in the dBASE III language and operates using the dBASE III system. Although the mHRS/HRS software package was developed for use at DOE facilities, it has direct applicability to the performing of CERCLA Phase I evaluations for any facility contaminated by hazardous waste. The software can perform evaluations using either the modified hazard ranking system methodology developed by DOE/PNL, the hazard ranking system methodology developed by EPA/MITRE Corp., or a combination of the two. This document is a companion manual to the mHRS/HRS user manual. It is intended for the programmer who must maintain the software package and for those interested in the computer implementation. This manual documents the system logic, computer programs, and data files that comprise the package. Hardware and software implementation requirements are discussed. In addition, hand calculations of three sample situations (problems) with associated computer runs used for the verification of program calculations are included

14 CFR 437.29 - Hazard analysis.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Hazard analysis. 437.29 Section 437.29... Documentation § 437.29 Hazard analysis. (a) An applicant must perform a hazard analysis that complies with § 437.55(a). (b) An applicant must provide to the FAA all the results of each step of the hazard analysis...

The California Hazards Institute

Science.gov (United States)

Rundle, J. B.; Kellogg, L. H.; Turcotte, D. L.

2006-12-01

California's abundant resources are linked with its natural hazards. Earthquakes, landslides, wildfires, floods, tsunamis, volcanic eruptions, severe storms, fires, and droughts afflict the state regularly. These events have the potential to become great disasters, like the San Francisco earthquake and fire of 1906, that overwhelm the capacity of society to respond. At such times, the fabric of civic life is frayed, political leadership is tested, economic losses can dwarf available resources, and full recovery can take decades. A patchwork of Federal, state and local programs are in place to address individual hazards, but California lacks effective coordination to forecast, prevent, prepare for, mitigate, respond to, and recover from, the harmful effects of natural disasters. Moreover, we do not know enough about the frequency, size, time, or locations where they may strike, nor about how the natural environment and man-made structures would respond. As California's population grows and becomes more interdependent, even moderate events have the potential to trigger catastrophes. Natural hazards need not become natural disasters if they are addressed proactively and effectively, rather than reactively. The University of California, with 10 campuses distributed across the state, has world-class faculty and students engaged in research and education in all fields of direct relevance to hazards. For that reason, the UC can become a world leader in anticipating and managing natural hazards in order to prevent loss of life and property and degradation of environmental quality. The University of California, Office of the President, has therefore established a new system-wide Multicampus Research Project, the California Hazards Institute (CHI), as a mechanism to research innovative, effective solutions for California. The CHI will build on the rich intellectual capital and expertise of the Golden State to provide the best available science, knowledge and tools for

Bench-marking beam-beam simulations using coherent quadrupole effects

International Nuclear Information System (INIS)

Krishnagopal, S.; Chin, Y.H.

1992-06-01

Computer simulations are used extensively in the study of the beam-beam interaction. The proliferation of such codes raises the important question of their reliability, and motivates the development of a dependable set of bench-marks. We argue that rather than detailed quantitative comparisons, the ability of different codes to predict the same qualitative physics should be used as a criterion for such bench-marks. We use the striking phenomenon of coherent quadrupole oscillations as one such bench-mark, and demonstrate that our codes do indeed observe this behaviour. We also suggest some other tests that could be used as bench-marks

Bench-marking beam-beam simulations using coherent quadrupole effects

International Nuclear Information System (INIS)

Krishnagopal, S.; Chin, Y.H.

1992-01-01

Computer simulations are used extensively in the study of the beam-beam interaction. The proliferation of such codes raises the important question of their reliability, and motivates the development of a dependable set of bench-marks. We argue that rather than detailed quantitative comparisons, the ability of different codes to predict the same qualitative physics should be used as a criterion for such bench-marks. We use the striking phenomenon of coherent quadrupole oscillations as one such bench-mark, and demonstrate that our codes do indeed observe this behavior. We also suggest some other tests that could be used as bench-marks

Risk Governance of Multiple Natural Hazards: Centralized versus Decentralized Approach in Europe

Science.gov (United States)

Komendantova, Nadejda; Scolobig, Anna; Vinchon, Charlotte

2014-05-01

The multi-risk approach is a relatively new field and its definition includes the need to consider multiple hazards and vulnerabilities in their interdependency (Selva, 2013) and the current multi-hazards disasters, such as the 2011 Tohoku earthquake, tsunami and nuclear catastrophe, showed the need for a multi-risk approach in hazard mitigation and management. Our knowledge about multi-risk assessment, including studies from different scientific disciplines and developed assessment tools, is constantly growing (White et al., 2001). However, the link between scientific knowledge, its implementation and the results in terms of improved governance and decision-making have gained significantly less attention (IRGC, 2005; Kappes et al., 2012), even though the interest to risk governance, in general, has increased significantly during the last years (Verweiy and Thompson, 2006). Therefore, the key research question is how risk assessment is implemented and what is the potential for the implementation of a multi-risk approach in different governance systems across Europe. More precisely, how do the characteristics of risk governance, such as the degree of centralization versus decentralization, influence the implementation of a multi-risk approach. The methodology of this research includes comparative case study analysis of top-down and bottom-up interactions in governance in the city of Naples, (Italy), where the institutional landscape is marked by significant autonomy of Italian regions in decision-making processes for assessing the majority of natural risks, excluding volcanic, and in Guadeloupe, French West Indies, an overseas department of France, where the decision-making process is marked by greater centralization in decision making associated with a well established state governance within regions, delegated to the prefect and decentralised services of central ministries. The research design included documentary analysis and extensive empirical work involving

The Information Literacy of Survey Mark Hunting: A Dialogue

Directory of Open Access Journals (Sweden)

Jennifer Galas

2016-11-01

Full Text Available In Brief: This article makes connections between the ACRL Framework for Information Literacy for Higher Education and the activity of survey mark hunting. After a brief review of the literature related to geographic information systems (GIS, information literacy, and gamification of learning, the authors enter into a dialogue in which they discover and describe the various ways information literacy is both required by and developed through the recreational activity of survey mark hunting. Through their dialogue they found that the activity of survey mark hunting relies on the construction of both information and its authority in ways contextualized within the communities that participate; that survey mark hunting is a conversation that builds on the past, where lived experience counts as evidence; and, that survey mark hunting is both a metaphor and embodied enactment of information literacy.

Uncertainty on shallow landslide hazard assessment: from field data to hazard mapping

Science.gov (United States)

Trefolini, Emanuele; Tolo, Silvia; Patelli, Eduardo; Broggi, Matteo; Disperati, Leonardo; Le Tuan, Hai

2015-04-01

Shallow landsliding that involve Hillslope Deposits (HD), the surficial soil that cover the bedrock, is an important process of erosion, transport and deposition of sediment along hillslopes. Despite Shallow landslides generally mobilize relatively small volume of material, they represent the most hazardous factor in mountain regions due to their high velocity and the common absence of warning signs. Moreover, increasing urbanization and likely climate change make shallow landslides a source of widespread risk, therefore the interest of scientific community about this process grown in the last three decades. One of the main aims of research projects involved on this topic, is to perform robust shallow landslides hazard assessment for wide areas (regional assessment), in order to support sustainable spatial planning. Currently, three main methodologies may be implemented to assess regional shallow landslides hazard: expert evaluation, probabilistic (or data mining) methods and physical models based methods. The aim of this work is evaluate the uncertainty of shallow landslides hazard assessment based on physical models taking into account spatial variables such as: geotechnical and hydrogeologic parameters as well as hillslope morphometry. To achieve this goal a wide dataset of geotechnical properties (shear strength, permeability, depth and unit weight) of HD was gathered by integrating field survey, in situ and laboratory tests. This spatial database was collected from a study area of about 350 km2 including different bedrock lithotypes and geomorphological features. The uncertainty associated to each step of the hazard assessment process (e.g. field data collection, regionalization of site specific information and numerical modelling of hillslope stability) was carefully characterized. The most appropriate probability density function (PDF) was chosen for each numerical variable and we assessed the uncertainty propagation on HD strength parameters obtained by

Factors influencing survival and mark retention in postmetamorphic boreal chorus frogs

Science.gov (United States)

Swanson, Jennifer E; Bailey, Larissa L.; Muths, Erin L.; Funk, W. Chris

2013-01-01

The ability to track individual animals is crucial in many field studies and often requires applying marks to captured individuals. Toe clipping has historically been a standard marking method for wild amphibian populations, but more recent marking methods include visual implant elastomer and photo identification. Unfortunately, few studies have investigated the influence and effectiveness of marking methods for recently metamorphosed individuals and as a result little is known about this life-history phase for most amphibians. Our focus was to explore survival probabilities, mark retention, and mark migration in postmetamorphic Boreal Chorus Frogs (Psuedacris maculata) in a laboratory setting. One hundred forty-seven individuals were assigned randomly to two treatment groups or a control group. Frogs in the first treatment group were marked with visual implant elastomer, while frogs in the second treatment group were toe clipped. Growth and mortality were recorded for one year and resulting data were analyzed using known-fate models in Program MARK. Model selection results suggested that survival probabilities of frogs varied with time and showed some variation among marking treatments. We found that frogs with multiple toes clipped on the same foot had lower survival probabilities than individuals in other treatments, but individuals can be marked by clipping a single toe on two different feet without any mark loss or negative survival effects. Individuals treated with visual implant elastomer had a mark migration rate of 4% and mark loss rate of 6%, and also showed very little negative survival impacts relative to control individuals.

Occupational, social, and relationship hazards and psychological distress among low-income workers: implications of the 'inverse hazard law'.

Science.gov (United States)

Krieger, Nancy; Kaddour, Afamia; Koenen, Karestan; Kosheleva, Anna; Chen, Jarvis T; Waterman, Pamela D; Barbeau, Elizabeth M

2011-03-01

Few studies have simultaneously included exposure information on occupational hazards, relationship hazards (eg, intimate partner violence) and social hazards (eg, poverty and racial discrimination), especially among low-income multiracial/ethnic populations. A cross-sectional study (2003-2004) of 1202 workers employed at 14 worksites in the greater Boston area of Massachusetts investigated the independent and joint association of occupational, social and relationship hazards with psychological distress (K6 scale). Among this low-income cohort (45% were below the US poverty line), exposure to occupational, social and relationship hazards, per the 'inverse hazard law,' was high: 82% exposed to at least one occupational hazard, 79% to at least one social hazard, and 32% of men and 34% of women, respectively, stated they had been the perpetrator or target of intimate partner violence (IPV). Fully 15.4% had clinically significant psychological distress scores (K6 score ≥ 13). All three types of hazards, and also poverty, were independently associated with increased risk of psychological distress. In models including all three hazards, however, significant associations with psychological distress occurred among men and women for workplace abuse and high exposure to racial discrimination only; among men, for IPV; and among women, for high exposure to occupational hazards, poverty and smoking. Reckoning with the joint and embodied reality of diverse types of hazards involving how people live and work is necessary for understanding determinants of health status.

Occupational health hazards in veterinary medicine: Zoonoses and other biological hazards

Science.gov (United States)

Epp, Tasha; Waldner, Cheryl

2012-01-01

This study describes biological hazards reported by veterinarians working in western Canada obtained through a self-administered mailed questionnaire. The potential occupational hazards included as biological hazards were zoonotic disease events, exposure to rabies, injuries due to bites and scratches, and allergies. Only 16.7% (136/812) of responding veterinarians reported the occurrence of a zoonosis or exposure to rabies in the past 5 years; the most commonly reported event was ringworm. Most bites and scratches (86%) described by 586 veterinarians involved encounters with cats; 81% of the resulting 163 infections were due to cat bites or scratches. Approximately 38% of participants reported developing an allergy during their career, with 41% of the affected individuals altering the way they practiced in response to their allergy. PMID:22851775

There's Life in Hazard Trees

Science.gov (United States)

Mary Torsello; Toni McLellan

The goals of hazard tree management programs are to maximize public safety and maintain a healthy sustainable tree resource. Although hazard tree management frequently targets removal of trees or parts of trees that attract wildlife, it can take into account a diversity of tree values. With just a little extra planning, hazard tree management can be highly beneficial...

Staff technical position on investigations to identify fault displacement hazards and seismic hazards at a geologic repository

International Nuclear Information System (INIS)

McConnell, K.I.; Blackford, M.E.; Ibrahim, A.K.

1992-07-01

The purpose of this Staff Technical Position (STP) is to provide guidance to the US Department of Energy (DOE) on acceptable geologic repository investigations that can be used to identify fault displacement hazards and seismic hazards. ne staff considers that the approach this STP takes to investigations of fault displacement and seismic phenomena is appropriate for the collection of sufficient data for input to analyses of fault displacement hazards and seismic hazards, both for the preclosure and postclosure performance periods. However, detailed analyses of fault displacement and seismic data, such as those required for comprehensive assessments of repository performance, may identify the need for additional investigations. Section 2.0 of this STP describes the 10 CFR Part 60 requirements that form the basis for investigations to describe fault displacement hazards and seismic hazards at a geologic repository. Technical position statements and corresponding discussions are presented in Sections 3.0 and 4.0, respectively. Technical position topics in this STP are categorized thusly: (1) investigation considerations, (2) investigations for fault-displacement hazards, and (3) investigations for seismic hazards

Mark Antony’s Homoeroticism in Cicero’s second Philippic

Directory of Open Access Journals (Sweden)

Bruna Fernanda Abreu

2017-06-01

Full Text Available Considering the concept of homosexuality in the ancient Rome, we attempt to analise how Cicero expose the Mark Antony’s “homosexuality” in his second Philippic. This speech is characterized by political and, mainly, personal accusations from Cicero to Mark Antony, and the Mark Antony’s passivity in his intercourses can be considered a topos of this invective speech.

The Impact Hazard in the Context of Other Natural Hazards and Predictive Science

Science.gov (United States)

Chapman, C. R.

1998-09-01

The hazard due to impact of asteroids and comets has been recognized as analogous, in some ways, to other infrequent but consequential natural hazards (e.g. floods and earthquakes). Yet, until recently, astronomers and space agencies have felt no need to do what their colleagues and analogous agencies must do in order the assess, quantify, and communicate predictions to those with a practical interest in the predictions (e.g. public officials who must assess the threats, prepare for mitigation, etc.). Recent heightened public interest in the impact hazard, combined with increasing numbers of "near misses" (certain to increase as Spaceguard is implemented) requires that astronomers accept the responsibility to place their predictions and assessments in terms that may be appropriately considered. I will report on preliminary results of a multi-year GSA/NCAR study of "Prediction in the Earth Sciences: Use and Misuse in Policy Making" in which I have represented the impact hazard, while others have treated earthquakes, floods, weather, global climate change, nuclear waste disposal, acid rain, etc. The impact hazard presents an end-member example of a natural hazard, helping those dealing with more prosaic issues to learn from an extreme. On the other hand, I bring to the astronomical community some lessons long adopted in other cases: the need to understand the policy purposes of impact predictions, the need to assess potential societal impacts, the requirements to very carefully assess prediction uncertainties, considerations of potential public uses of the predictions, awareness of ethical considerations (e.g. conflicts of interest) that affect predictions and acceptance of predictions, awareness of appropriate means for publicly communicating predictions, and considerations of the international context (especially for a hazard that knows no national boundaries).

29 CFR 1917.25 - Fumigants, pesticides, insecticides and hazardous preservatives (see also § 1917.2 Hazardous...

Science.gov (United States)

2010-07-01

... 29 Labor 7 2010-07-01 2010-07-01 false Fumigants, pesticides, insecticides and hazardous..., DEPARTMENT OF LABOR (CONTINUED) MARINE TERMINALS Marine Terminal Operations § 1917.25 Fumigants, pesticides... fumigants, pesticides or hazardous preservatives have created a hazardous atmosphere. These signs shall note...

Preoperative Site Marking: Are We Adhering to Good Surgical Practice?

Science.gov (United States)

Bathla, Sonia; Chadwick, Michael; Nevins, Edward J; Seward, Joanna

2017-06-29

Wrong-site surgery is a never event and a serious, preventable patient safety incident. Within the United Kingdom, national guidance has been issued to minimize the risk of such events. The mandate includes preoperative marking of all surgical patients. This study aimed to quantify regional variation in practice within general surgery and opinions of the surgeons, to help guide the formulation and implementation of a regional general surgery preoperative marking protocol. A SurveyMonkey questionnaire was designed and distributed to 120 surgeons within the Mersey region, United Kingdom. This included all surgical trainees in Mersey (47 registrars, 56 core trainees), 15 consultants, and 2 surgical care practitioners. This sought to ascertain their routine practice and how they would choose to mark for 12 index procedures in general surgery, if mandated to do so. A total of 72 responses (60%) were obtained to the SurveyMonkey questionnaire. Only 26 (36.1%) said that they routinely marked all of their patients preoperatively. The operating surgeon marked the patient in 69% of responses, with the remainder delegating this task. Markings were visible after draping in only 55.6% of marked cases. Based on our findings, surgeons may not be adhering to "Good Surgical Practice"; practice is widely variable and surgeons are largely opposed and resistant to marking patients unless laterality is involved. We suggest that all surgeons need to be actively engaged in the design of local marking protocols to gain support, change practice, and reduce errors.

Hazardous Waste Manifest System

Science.gov (United States)

EPA’s hazardous waste manifest system is designed to track hazardous waste from the time it leaves the generator facility where it was produced, until it reaches the off-site waste management facility that will store, treat, or dispose of the waste.

LAV@HAZARD: a web-GIS interface for volcanic hazard assessment

Directory of Open Access Journals (Sweden)

Giovanni Gallo

2011-12-01

Full Text Available Satellite data, radiative power of hot spots as measured with remote sensing, historical records, on site geological surveys, digital elevation model data, and simulation results together provide a massive data source to investigate the behavior of active volcanoes like Mount Etna (Sicily, Italy over recent times. The integration of these heterogeneous data into a coherent visualization framework is important for their practical exploitation. It is crucial to fill in the gap between experimental and numerical data, and the direct human perception of their meaning. Indeed, the people in charge of safety planning of an area need to be able to quickly assess hazards and other relevant issues even during critical situations. With this in mind, we developed LAV@HAZARD, a web-based geographic information system that provides an interface for the collection of all of the products coming from the LAVA project research activities. LAV@HAZARD is based on Google Maps application programming interface, a choice motivated by its ease of use and the user-friendly interactive environment it provides. In particular, the web structure consists of four modules for satellite applications (time-space evolution of hot spots, radiant flux and effusion rate, hazard map visualization, a database of ca. 30,000 lava-flow simulations, and real-time scenario forecasting by MAGFLOW on Compute Unified Device Architecture.

Hazard Detection Software for Lunar Landing

Science.gov (United States)

Huertas, Andres; Johnson, Andrew E.; Werner, Robert A.; Montgomery, James F.

2011-01-01

The Autonomous Landing and Hazard Avoidance Technology (ALHAT) Project is developing a system for safe and precise manned lunar landing that involves novel sensors, but also specific algorithms. ALHAT has selected imaging LIDAR (light detection and ranging) as the sensing modality for onboard hazard detection because imaging LIDARs can rapidly generate direct measurements of the lunar surface elevation from high altitude. Then, starting with the LIDAR-based Hazard Detection and Avoidance (HDA) algorithm developed for Mars Landing, JPL has developed a mature set of HDA software for the manned lunar landing problem. Landing hazards exist everywhere on the Moon, and many of the more desirable landing sites are near the most hazardous terrain, so HDA is needed to autonomously and safely land payloads over much of the lunar surface. The HDA requirements used in the ALHAT project are to detect hazards that are 0.3 m tall or higher and slopes that are 5 or greater. Steep slopes, rocks, cliffs, and gullies are all hazards for landing and, by computing the local slope and roughness in an elevation map, all of these hazards can be detected. The algorithm in this innovation is used to measure slope and roughness hazards. In addition to detecting these hazards, the HDA capability also is able to find a safe landing site free of these hazards for a lunar lander with diameter .15 m over most of the lunar surface. This software includes an implementation of the HDA algorithm, software for generating simulated lunar terrain maps for testing, hazard detection performance analysis tools, and associated documentation. The HDA software has been deployed to Langley Research Center and integrated into the POST II Monte Carlo simulation environment. The high-fidelity Monte Carlo simulations determine the required ground spacing between LIDAR samples (ground sample distances) and the noise on the LIDAR range measurement. This simulation has also been used to determine the effect of

Enriquillo–Plantain Garden fault zone in Jamaica: paleoseismology and seismic hazard

Science.gov (United States)

Koehler, R.D.; Mann, P.; Prentice, Carol S.; Brown, L.; Benford, B.; Grandison-Wiggins, M.

2013-01-01

The countries of Jamaica, Haiti, and the Dominican Republic all straddle the Enriquillo–Plantain Garden fault zone ( EPGFZ), a major left-lateral, strike-slip fault system bounding the Caribbean and North American plates. Past large earthquakes that destroyed the capital cities of Kingston, Jamaica (1692, 1907), and Port-au-Prince, Haiti (1751, 1770), as well as the 2010 Haiti earthquake that killed more than 50,000 people, have heightened awareness of seismic hazards in the northern Caribbean. We present here new geomorphic and paleoseismic information bearing on the location and relative activity of the EPGFZ, which marks the plate boundary in Jamaica. Documentation of a river bank exposure and several trenches indicate that this fault is active and has the potential to cause major destructive earthquakes in Jamaica. The results suggest that the fault has not ruptured the surface in at least 500 yr and possibly as long as 28 ka. The long period of quiescence and subdued geomorphic expression of the EPGFZ indicates that it may only accommodate part of the ∼7–9 mm=yr plate deformation rate measured geodetically and that slip may be partitioned on other undocumented faults. Large uncertainties related to the neotectonic framework of Jamaica remain and more detailed fault characterization studies are necessary to accurately assess seismic hazards.

Hydrothermal Liquefaction Treatment Preliminary Hazard Analysis Report

Energy Technology Data Exchange (ETDEWEB)

Lowry, Peter P.; Wagner, Katie A.

2015-08-31

A preliminary hazard assessment was completed during February 2015 to evaluate the conceptual design of the modular hydrothermal liquefaction treatment system. The hazard assessment was performed in 2 stages. An initial assessment utilizing Hazard Identification and Preliminary Hazards Analysis (PHA) techniques identified areas with significant or unique hazards (process safety-related hazards) that fall outside of the normal operating envelope of PNNL and warranted additional analysis. The subsequent assessment was based on a qualitative What-If analysis. This analysis was augmented, as necessary, by additional quantitative analysis for scenarios involving a release of hazardous material or energy with the potential for affecting the public.

Virtual tool mark generation for efficient striation analysis in forensic science

Energy Technology Data Exchange (ETDEWEB)

Ekstrand, Laura [Iowa State Univ., Ames, IA (United States)

2012-01-01

In 2009, a National Academy of Sciences report called for investigation into the scienti c basis behind tool mark comparisons (National Academy of Sciences, 2009). Answering this call, Chumbley et al. (2010) attempted to prove or disprove the hypothesis that tool marks are unique to a single tool. They developed a statistical algorithm that could, in most cases, discern matching and non-matching tool marks made at di erent angles by sequentially numbered screwdriver tips. Moreover, in the cases where the algorithm misinterpreted a pair of marks, an experienced forensics examiner could discern the correct outcome. While this research served to con rm the basic assumptions behind tool mark analysis, it also suggested that statistical analysis software could help to reduce the examiner's workload. This led to a new tool mark analysis approach, introduced in this thesis, that relies on 3D scans of screwdriver tip and marked plate surfaces at the micrometer scale from an optical microscope. These scans are carefully cleaned to remove noise from the data acquisition process and assigned a coordinate system that mathematically de nes angles and twists in a natural way. The marking process is then simulated by using a 3D graphics software package to impart rotations to the tip and take the projection of the tip's geometry in the direction of tool travel. The edge of this projection, retrieved from the 3D graphics software, becomes a virtual tool mark. Using this method, virtual marks are made at increments of 5 and compared to a scan of the evidence mark. The previously developed statistical package from Chumbley et al. (2010) performs the comparison, comparing the similarity of the geometry of both marks to the similarity that would occur due to random chance. The resulting statistical measure of the likelihood of the match informs the examiner of the angle of the best matching virtual mark, allowing the examiner to focus his/her mark analysis on a smaller range of angles

Preliminary hazards analysis -- vitrification process

International Nuclear Information System (INIS)

Coordes, D.; Ruggieri, M.; Russell, J.; TenBrook, W.; Yimbo, P.

1994-06-01

This paper presents a Preliminary Hazards Analysis (PHA) for mixed waste vitrification by joule heating. The purpose of performing a PHA is to establish an initial hazard categorization for a DOE nuclear facility and to identify those processes and structures which may have an impact on or be important to safety. The PHA is typically performed during and provides input to project conceptual design. The PHA is then followed by a Preliminary Safety Analysis Report (PSAR) performed during Title 1 and 2 design. The PSAR then leads to performance of the Final Safety Analysis Report performed during the facility's construction and testing. It should be completed before routine operation of the facility commences. This PHA addresses the first four chapters of the safety analysis process, in accordance with the requirements of DOE Safety Guidelines in SG 830.110. The hazards associated with vitrification processes are evaluated using standard safety analysis methods which include: identification of credible potential hazardous energy sources; identification of preventative features of the facility or system; identification of mitigative features; and analyses of credible hazards. Maximal facility inventories of radioactive and hazardous materials are postulated to evaluate worst case accident consequences. These inventories were based on DOE-STD-1027-92 guidance and the surrogate waste streams defined by Mayberry, et al. Radiological assessments indicate that a facility, depending on the radioactive material inventory, may be an exempt, Category 3, or Category 2 facility. The calculated impacts would result in no significant impact to offsite personnel or the environment. Hazardous materials assessment indicates that a Mixed Waste Vitrification facility will be a Low Hazard facility having minimal impacts to offsite personnel and the environment

Preliminary hazards analysis -- vitrification process

Energy Technology Data Exchange (ETDEWEB)

Coordes, D.; Ruggieri, M.; Russell, J.; TenBrook, W.; Yimbo, P. [Science Applications International Corp., Pleasanton, CA (United States)

1994-06-01

This paper presents a Preliminary Hazards Analysis (PHA) for mixed waste vitrification by joule heating. The purpose of performing a PHA is to establish an initial hazard categorization for a DOE nuclear facility and to identify those processes and structures which may have an impact on or be important to safety. The PHA is typically performed during and provides input to project conceptual design. The PHA is then followed by a Preliminary Safety Analysis Report (PSAR) performed during Title 1 and 2 design. The PSAR then leads to performance of the Final Safety Analysis Report performed during the facility`s construction and testing. It should be completed before routine operation of the facility commences. This PHA addresses the first four chapters of the safety analysis process, in accordance with the requirements of DOE Safety Guidelines in SG 830.110. The hazards associated with vitrification processes are evaluated using standard safety analysis methods which include: identification of credible potential hazardous energy sources; identification of preventative features of the facility or system; identification of mitigative features; and analyses of credible hazards. Maximal facility inventories of radioactive and hazardous materials are postulated to evaluate worst case accident consequences. These inventories were based on DOE-STD-1027-92 guidance and the surrogate waste streams defined by Mayberry, et al. Radiological assessments indicate that a facility, depending on the radioactive material inventory, may be an exempt, Category 3, or Category 2 facility. The calculated impacts would result in no significant impact to offsite personnel or the environment. Hazardous materials assessment indicates that a Mixed Waste Vitrification facility will be a Low Hazard facility having minimal impacts to offsite personnel and the environment.

French people addressing environmental hazards (Eser 2013)

International Nuclear Information System (INIS)

Pautard, Eric; Moreau, Sylvain; Bottin, Anne; Kraszewski, Marlene; Fretin, David; Carriere, Celine; Bird, Geoffrey

2015-07-01

This publication presents the results of a survey, conducted towards the end of 2013, of 4,700 people resident in metropolitan France and its 'departements d'outre-mer' (DOM - overseas departments). The aim of the survey was to ascertain how French people perceive natural hazards (flooding, earthquakes, climate events, cyclones, etc.) and technological hazards (industrial and nuclear) to which they may be exposed. Questioned as to whether or not they felt exposed to one or several environmental hazards in their place of residence, French people's answers varied somewhat depending on the hazard invoked and place of residence. A strong feeling of exposure was expressed most frequently in the DOM. Respondents in both metropolitan France and DOM think that atmospheric pollution is a significant hazard (56%) but their opinions diverge partially where other hazards are concerned. Natural hazards (earthquakes and flooding) are cited most frequently overseas, whereas technological hazards (industrial and nuclear) are primarily metropolitan concerns. Climate change related hazards are seen as a threat by 56% of overseas respondents and by 42% in the mother country. In general, one-third of French people think that they are exposed to more than two environmental hazards. Unlike the younger members of the population, only one-quarter of respondents of 65 years of age or over felt exposed to three or more hazards. From municipal level databases providing information on exposure to flooding and technological and climate-related hazards, the survey indicates that a large majority of respondents living in these municipalities either do not feel at risk from existing hazards or feel that the risk is low (see figure below). It is in the area of climate-related hazards that awareness of threat seems to be highest in France, and more particularly in the DOM. In the face of the flooding that could affect them, overseas populations are more aware of this natural

Seismic hazard assessment of Iran

Directory of Open Access Journals (Sweden)

M. Ghafory-Ashtiany

1999-06-01

Full Text Available The development of the new seismic hazard map of Iran is based on probabilistic seismic hazard computation using the historical earthquakes data, geology, tectonics, fault activity and seismic source models in Iran. These maps have been prepared to indicate the earthquake hazard of Iran in the form of iso-acceleration contour lines, and seismic hazard zoning, by using current probabilistic procedures. They display the probabilistic estimates of Peak Ground Acceleration (PGA for the return periods of 75 and 475 years. The maps have been divided into intervals of 0.25 degrees in both latitudinal and longitudinal directions to calculate the peak ground acceleration values at each grid point and draw the seismic hazard curves. The results presented in this study will provide the basis for the preparation of seismic risk maps, the estimation of earthquake insurance premiums, and the preliminary site evaluation of critical facilities.

Selection of gender marked morphemes in speech production

NARCIS (Netherlands)

Schriefers, H.J.; Jescheniak, J.D.; Hantsch, A.

2005-01-01

N.O. Schiller and A. Caramazza (2003) and A. Costa, D. Kovacic, E. Fedorenko, and A. Caramazza (2003) have argued that the processing of freestanding gender-marked morphemes (e.g., determiners) and bound gender-marked morphemes (e.g., adjective suffixes) during syntactic encoding in speech

Identification of Aircraft Hazards

International Nuclear Information System (INIS)

K. Ashley

2006-01-01

Aircraft hazards were determined to be potentially applicable to a repository at Yucca Mountain in ''Monitored Geological Repository External Events Hazards Screening Analysis'' (BSC 2005 [DIRS 174235], Section 6.4.1). That determination was conservatively based upon limited knowledge of flight data in the area of concern and upon crash data for aircraft of the type flying near Yucca Mountain. The purpose of this report is to identify specific aircraft hazards that may be applicable to a monitored geologic repository (MGR) at Yucca Mountain, using NUREG-0800, ''Standard Review Plan for the Review of Safety Analysis Reports for Nuclear Power Plants'' (NRC 1987 [DIRS 103124], Section 3.5.1.6), as guidance for the inclusion or exclusion of identified aircraft hazards. The intended use of this report is to provide inputs for further screening and analysis of identified aircraft hazards based upon the criteria that apply to Category 1 and Category 2 event sequence analyses as defined in 10 CFR 63.2 [DIRS 176544] (Section 4). The scope of this report includes the evaluation of military, private, and commercial use of airspace in the 100-mile regional setting of the repository at Yucca Mountain with the potential for reducing the regional setting to a more manageable size after consideration of applicable screening criteria (Section 7)

A method for studying knife tool marks on bone.

Science.gov (United States)

Shaw, Kai-Ping; Chung, Ju-Hui; Chung, Fang-Chun; Tseng, Bo-Yuan; Pan, Chih-Hsin; Yang, Kai-Ting; Yang, Chun-Pang

2011-07-01

The characteristics of knife tool marks retained on hard tissues can be used to outline the shape and angle of a knife. The purpose of this study was to describe such marks on bone tissues that had been chopped with knives. A chopping stage with a gravity accelerator and a fixed bone platform was designed to reconstruct the chopping action. A digital microscope was also used to measure the knife angle (θ) and retained V-shape tool mark angle (ψ) in a pig skull. The κ value (elasticity coefficient; θ/ψ) was derived and recorded after the knife angle (θ) and the accompanied velocity were compared with the proportional impulsive force of the knife and ψ on the bone. The constant impulsive force revealed a correlation between the V-shape tool mark angle (ψ) and the elasticity coefficient (κ). These results describe the tool marks--crucial in the medicolegal investigation--of a knife on hard tissues. © 2011 American Academy of Forensic Sciences.

75 FR 58346 - Hazardous Waste Management System; Identification and Listing of Hazardous Waste

Science.gov (United States)

2010-09-24

... Waste Management System; Identification and Listing of Hazardous Waste AGENCY: Environmental Protection... Chemical Company-Texas Operations (Eastman) to exclude (or delist) certain solid wastes generated by its Longview, Texas, facility from the lists of hazardous wastes. EPA used the Delisting Risk Assessment...

Integrating Volcanic Hazard Data in a Systematic Approach to Develop Volcanic Hazard Maps in the Lesser Antilles

Directory of Open Access Journals (Sweden)

Jan M. Lindsay

2018-04-01

Full Text Available We report on the process of generating the first suite of integrated volcanic hazard zonation maps for the islands of Dominica, Grenada (including Kick ‘em Jenny and Ronde/Caille, Nevis, Saba, St. Eustatius, St. Kitts, Saint Lucia, and St Vincent in the Lesser Antilles. We developed a systematic approach that accommodated the range in prior knowledge of the volcanoes in the region. A first-order hazard assessment for each island was used to develop one or more scenario(s of likely future activity, for which scenario-based hazard maps were generated. For the most-likely scenario on each island we also produced a poster-sized integrated volcanic hazard zonation map, which combined the individual hazardous phenomena depicted in the scenario-based hazard maps into integrated hazard zones. We document the philosophy behind the generation of this suite of maps, and the method by which hazard information was combined to create integrated hazard zonation maps, and illustrate our approach through a case study of St. Vincent. We also outline some of the challenges we faced using this approach, and the lessons we have learned by observing how stakeholders have interacted with the maps over the past ~10 years. Based on our experience, we recommend that future map makers involve stakeholders in the entire map generation process, especially when making design choices such as type of base map, use of colour and gradational boundaries, and indeed what to depict on the map. We also recommend careful consideration of how to evaluate and depict offshore hazard of island volcanoes, and recommend computer-assisted modelling of all phenomena to generate more realistic hazard footprints. Finally, although our systematic approach to integrating individual hazard data into zones generally worked well, we suggest that a better approach might be to treat the integration of hazards on a case-by-case basis to ensure the final product meets map users' needs. We hope that

Ultrafast lasers for precise and corrosion free marking on chirurgical steels

Science.gov (United States)

Neugebauer, Christoph; Aalderink, Dennis; Maurer, Erich; Faisst, Birgit; Budnicki, Aleksander

2017-02-01

The unique properties of ultrashort laser pulses and the decrease of invest pave the way to numerous novel applications. Even in the very price sensitive field of laser marking, ultrashort laser can compete due to a new cost structure and remarkable properties of the marking results. In this study we concentrated on industrial marking of medical equipment by using IR ultrashort lasers and compared the results with common marking laser systems. We demonstrate the benefits of ultrashort lasers marking on chirurgical devices, observing the influence of pulse energy, pulse duration, scanning velocity in respect to the visibility, corrosion resistance and long term durability under clinical conditions. Nowadays many parts and products are marked for the purpose of identification and traceability. One kind of laser marking is the well known annealing of stainless steel by nanosecond marking lasers. When annealing occurs a colored oxide layer grows due to the local heating of the material surface. Compared to the raw material, the annealed marking shows increased corrosion sensitivity. Regarding the traceability, the poor durability of the ns marking resulting in contrast reduction and the corrosion susceptibility are a huge problem. Therefore three different laser sources with ns-psfs pulse duration were observed. The focus rests on the realization of parameter studies (various lasers) and their effect on the corrosion and passivation behavior. Furthermore analysis of the oxide layers by use of EDX and XRD were performed to obtain further information on the composition and structure of the markings.

Marking system for scintillation camera and computer, and its clinical application

Energy Technology Data Exchange (ETDEWEB)

Narabayashi, I [Kinki Univ., Higashi-Osaka, Osaka (Japan); Ito, K; Yoshida, S; Yamaguchi, H; Kahata, S

1976-03-01

In routine clinical studies, we have noted that in some cases anatomical marks have been transferred to scintigrams through the scintillation camera. It was thought that radioactive point sources could be used as anatomical marks. However, this method resulted in an ill-defined area of brightness. The marking equipment for the scintillation camera used in this study consisted of a linear potentiometer and a sine-cosine potentiometer. We designed a marking method for a data processing system using the marking equipment for a scintillation camera. The data processing system of a scintillation camera is composed of EDR-4000 (8K core memories), MT recorder, CRT display, and graphic display unit and it is connected by on-line to the scintillation camera. A marking program was made in order to record marking addresses on a processed image. Using this soft program and graphpen of the graphic display unit, we transferred marks to processed image by points and lines. Subtraction scintigraphy using /sup 198/Au-colloid and /sup 75/Se-selenomethionine was performed on cases of pancreas carcinoma. After marking addresses were recorded on a processed image by this marking method, the signals from the scintillation camera were fed into the input controller. Then these signals with marking points were transferred from the computer to the MT recorder. Subtraction scintigraphy by this system made it possible to examine each picture with /sup 198/Au-colloid of /sup 75/Se-selenomethionine at different times.

Using road markings as a continuous cue for speed choice.

Science.gov (United States)

Charlton, Samuel G; Starkey, Nicola J; Malhotra, Neha

2018-08-01

The potential for using road markings to indicate speed limits was investigated in a driving simulator over the course of two sessions. Two types of experimental road markings, an "Attentional" set designed to provide visually distinct cues to indicate speed limits of 60, 80 and 100 km/h, and a "Perceptual" set designed to also affect drivers' perception of speed, were compared to a standard undifferentiated set of markings. Participants (n = 20 per group) were assigned to one of four experimental groups (Attentional-Explicit, Attentional-Implicit, Perceptual-Explicit, Perceptual-Implicit) or a Control group (n = 22; standard road markings). The Explicit groups were instructed about the meaning of the road markings while those in the Implicit and Control groups did not receive any explanation. Participants drove five 10 km simulated roads containing three speed zones (60, 80 and 100 km/h) during the first session. The participants returned to the laboratory approximately 3 days later to drive five more trials including roads they had not seen before, a trial that included a secondary task, and a trial where speed signs were removed and only markings were present. The findings indicated that both types of road markings improved drivers' compliance with speed limits compared to the control group, but that explicit instruction as to the meaning of the markings was needed to realise their full benefit. Although previous research has indicated the benefit of road markings used as warnings to indicate speed reductions in advance of horizontal or vertical curves, the findings of the present experiment also suggest that systematically associating road markings with specific speed limits may be a useful way to improve speed limit compliance and increase speed homogeneity. Copyright © 2018 The Authors. Published by Elsevier Ltd.. All rights reserved.

Using hazard maps to identify and eliminate workplace hazards: a union-led health and safety training program.

Science.gov (United States)

Anderson, Joe; Collins, Michele; Devlin, John; Renner, Paul

2012-01-01

The Institute for Sustainable Work and Environment and the Utility Workers Union of America worked with a professional evaluator to design, implement, and evaluate the results of a union-led system of safety-based hazard identification program that trained workers to use hazard maps to identify workplace hazards and target them for elimination. The evaluation documented program implementation and impact using data collected from both qualitative interviews and an on-line survey from worker trainers, plant managers, and health and safety staff. Managers and workers reported that not only were many dangerous hazards eliminated as a result of hazard mapping, some of which were long-standing, difficult-to-resolve issues, but the evaluation also documented improved communication between union members and management that both workers and managers agreed resulted in better, more sustainable hazard elimination.

Variable features on Mars. VII - Dark filamentary markings on Mars

Science.gov (United States)

Veverka, J.

1976-01-01

The paper discusses the location, variability, and possible nature of well-developed patterns of dark filamentary markings in the Mariner 9 photographic records. Although not common on Mars, the markings are concentrated in at least two areas: Depressio Hellespontica and Cerberus/Trivium Charontis. In certain localities, strong winds are required to bring these markings into prominence. The dark filamentary markings seem to be true albedo features controlled by local topography, it being unlikely that they are free linear dunes. The distinctive criss-cross pattern seen in many of the pictures suggests that jointing provides the controlling topographic grid. At this stage it cannot be inferred whether the markings are erosional or depositional in character.

The Mark II Vertex Drift Chamber

International Nuclear Information System (INIS)

Alexander, J.P.; Baggs, R.; Fujino, D.

1989-03-01

We have completed constructing and begun operating the Mark II Drift Chamber Vertex Detector. The chamber, based on a modified jet cell design, achieves 30 μm spatial resolution and 2 gas mixtures. Special emphasis has been placed on controlling systematic errors including the use of novel construction techniques which permit accurate wire placement. Chamber performance has been studied with cosmic ray tracks collected with the chamber located both inside and outside the Mark II. Results on spatial resolution, average pulse shape, and some properties of CO 2 mixtures are presented. 10 refs., 12 figs., 1 tab

Acceptance and stress effects of aircraft obstruction markings of wind turbines

International Nuclear Information System (INIS)

Pohl, Johannes; Hübner, Gundula; Mohs, Anja

2012-01-01

A dominant resistance factor against wind power projects seems to be their visual impact on the landscape. In addition stress effects from aircraft obstruction markings are an emerging topic related to acceptance. As the height of wind turbines increases, so does the number of mandatory obstruction markings. Recently, obstruction markings have caused a growing number of complaints from residents. Whether obstruction markings indeed cause stress or even substantial annoyance remains an open question. To analyse the stress impact of obstruction markings, we used environmental and stress psychology methodologies. Residents (N=420) with direct sight of turbines at 13 wind farms participated in a questionnaire survey. Evidence of substantial annoyance caused by obstruction markings was not found. However, residents exposed to xenon lights reported more intense and multifaceted stress responses than exposed to LED or colour markings on blades. Moreover, xenon lights negatively affected the general acceptance of wind energy. Additionally, synchronised navigation lights were found to be less annoying than non-synchronised lights under certain weather conditions. Markings with light intensity adjustment proved to be advantageous. To reduce stress and increase social acceptance of wind power, xenon lights should be abandoned, navigation lights synchronised, and light intensity adjustment applied. - Research highlights: ► Wind turbine obstruction markings influence the social acceptance of wind energy. ► Residents exposed to xenon lights reported more intense stress responses than exposed to LED or colour markings. ► Synchronised lights were found to be less annoying under certain weather conditions. ► Markings with light intensity adjustment proved to be advantageous. ► Evidence of substantial annoyance caused by obstruction markings was not found.

Administering and Detecting Protein Marks on Arthropods for Dispersal Research.

Science.gov (United States)

Hagler, James R; Machtley, Scott A

2016-01-28

Monitoring arthropod movement is often required to better understand associated population dynamics, dispersal patterns, host plant preferences, and other ecological interactions. Arthropods are usually tracked in nature by tagging them with a unique mark and then re-collecting them over time and space to determine their dispersal capabilities. In addition to actual physical tags, such as colored dust or paint, various types of proteins have proven very effective for marking arthropods for ecological research. Proteins can be administered internally and/or externally. The proteins can then be detected on recaptured arthropods with a protein-specific enzyme-linked immunosorbent assay (ELISA). Here we describe protocols for externally and internally tagging arthropods with protein. Two simple experimental examples are demonstrated: (1) an internal protein mark introduced to an insect by providing a protein-enriched diet and (2) an external protein mark topically applied to an insect using a medical nebulizer. We then relate a step-by-step guide of the sandwich and indirect ELISA methods used to detect protein marks on the insects. In this demonstration, various aspects of the acquisition and detection of protein markers on arthropods for mark-release-recapture, mark-capture, and self-mark-capture types of research are discussed, along with the various ways that the immunomarking procedure has been adapted to suit a wide variety of research objectives.

16 CFR 1500.5 - Hazardous mixtures.

Science.gov (United States)

2010-01-01

..., flammable, sensitizing, or pressure-generating properties of a substance from what is known about its... Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION FEDERAL HAZARDOUS SUBSTANCES ACT REGULATIONS HAZARDOUS SUBSTANCES AND ARTICLES; ADMINISTRATION AND ENFORCEMENT REGULATIONS § 1500.5 Hazardous mixtures...

Chemical process hazards analysis

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-02-01

The Office of Worker Health and Safety (EH-5) under the Assistant Secretary for the Environment, Safety and Health of the US Department (DOE) has published two handbooks for use by DOE contractors managing facilities and processes covered by the Occupational Safety and Health Administration (OSHA) Rule for Process Safety Management of Highly Hazardous Chemicals (29 CFR 1910.119), herein referred to as the PSM Rule. The PSM Rule contains an integrated set of chemical process safety management elements designed to prevent chemical releases that can lead to catastrophic fires, explosions, or toxic exposures. The purpose of the two handbooks, ``Process Safety Management for Highly Hazardous Chemicals`` and ``Chemical Process Hazards Analysis,`` is to facilitate implementation of the provisions of the PSM Rule within the DOE. The purpose of this handbook ``Chemical Process Hazards Analysis,`` is to facilitate, within the DOE, the performance of chemical process hazards analyses (PrHAs) as required under the PSM Rule. It provides basic information for the performance of PrHAs, and should not be considered a complete resource on PrHA methods. Likewise, to determine if a facility is covered by the PSM rule, the reader should refer to the handbook, ``Process Safety Management for Highly Hazardous Chemicals`` (DOE- HDBK-1101-96). Promulgation of the PSM Rule has heightened the awareness of chemical safety management issues within the DOE. This handbook is intended for use by DOE facilities and processes covered by the PSM rule to facilitate contractor implementation of the PrHA element of the PSM Rule. However, contractors whose facilities and processes not covered by the PSM Rule may also use this handbook as a basis for conducting process hazards analyses as part of their good management practices. This handbook explains the minimum requirements for PrHAs outlined in the PSM Rule. Nowhere have requirements been added beyond what is specifically required by the rule.

Preoperative stoma site marking in the general surgery population.

Science.gov (United States)

Zimnicki, Katherine M

2013-01-01

Preoperative teaching and stoma site marking are supported by research and professional organizations as interventions that can reduce the incidence of problematic stomas and improve patient outcomes. This study investigated the translation of this research into practice in the acute care surgery population. A retrospective chart review using convenience sampling was conducted at a large urban hospital in the Midwestern United States. Thirty patients underwent a surgical procedure that resulted in the creation of a fecal ostomy over a 5-month period. Descriptive statistical analysis examined the reason for surgery, preoperative length of stay (LOS), the percentage of patients who received preoperative teaching and stoma marking and the relationship between preoperative LOS and the use of preoperative teaching and stoma marking. Twenty-one of 30 patients were admitted to hospital 24 hours or more before surgery. No participants were admitted urgently. Three (14%) of those admitted for more than 24 hours received preoperative marking or teaching. There was no significant relationship between preoperative LOS and preoperative teaching and stoma marking. The opportunity exists to promote successful adaptation in this surgical population through the implementation of the evidence-based interventions of preoperative teaching and stoma marking. Additional study is needed to determine barriers to their use as well as to develop effective implementation strategies.

Banner Marks of Ottoman Perıod at Giresun Museum

Directory of Open Access Journals (Sweden)

Gazanfer İLTAR

2015-12-01

Full Text Available The eleven banner marks among those that were brought together in 1926 to establish a museum at Tokat Gök Medrese (the Celestial Madrasa was sent to Giresun Museum in 1995 in order to be displayed together with other two thousand archaeological and ethnographic pieces. On the banner of one of these marks that was produced with brass hammering technique was written the date “1118/1706-1707”, which is indicated on its inventory record. Such marks that were decorated by using thuluth writing and vegetative motifs were made in the forms of round, drop, palmet and tulip. Generally, there exists a hilly part in the forms of palmet and drop on most of these marks which consist a handle and a body part. Additionally, there appear writings as “Allah, Muhammed, the words of Tawheed, Allah-Muhammed-Ali” on these marks. Today, the marks some of which are exhibited on the display cases and some of which are stored in museums are important in the sense of obtaining information about the art of metalworking in the period these marks were produced.

A situational analysis of priority disaster hazards in Uganda: findings from a hazard and vulnerability analysis.

Science.gov (United States)

Mayega, R W; Wafula, M R; Musenero, M; Omale, A; Kiguli, J; Orach, G C; Kabagambe, G; Bazeyo, W

2013-06-01

Most countries in sub-Saharan Africa have not conducted a disaster risk analysis. Hazards and vulnerability analyses provide vital information that can be used for development of risk reduction and disaster response plans. The purpose of this study was to rank disaster hazards for Uganda, as a basis for identifying the priority hazards to guide disaster management planning. The study as conducted in Uganda, as part of a multi-country assessment. A hazard, vulnerability and capacity analysis was conducted in a focus group discussion of 7 experts representing key stakeholder agencies in disaster management in Uganda. A simple ranking method was used to rank the probability of occurance of 11 top hazards, their potential impact and the level vulnerability of people and infrastructure. In-terms of likelihood of occurance and potential impact, the top ranked disaster hazards in Uganda are: 1) Epidemics of infectious diseases, 2) Drought/famine, 3) Conflict and environmental degradation in that order. In terms of vulnerability, the top priority hazards to which people and infrastructure were vulnerable were: 1) Conflicts, 2) Epidemics, 3) Drought/famine and, 4) Environmental degradation in that order. Poverty, gender, lack of information, and lack of resilience measures were some of the factors promoting vulnerability to disasters. As Uganda develops a disaster risk reduction and response plan, it ought to prioritize epidemics of infectious diseases, drought/famine, conflics and environmental degradation as the priority disaster hazards.

Identification markings for gemstones

International Nuclear Information System (INIS)

Dreschhoff, G.A.M.; Zeller, E.J.

1980-01-01

A method is described of providing permanent identification markings to gemstones such as diamond crystals by irradiating the cooled gemstone with protons in the desired pattern. The proton bombardment results in a reaction limited to a defined plane and converting the bombarded area of the plane into a different crystal lattice from that of the preirradiated stone. (author)

Factors affecting scent-marking behaviour in Eurasion beaver (Castor fiber)

NARCIS (Netherlands)

Rosell, F.; Nolet, B.A.

1997-01-01

We tested the hypothesis that a main function of territory marking in Eurasian beaver (Castor fiber) is defense of the territory. The results showed that: (1) beaver colonies with close neighbors scent-mark more often than isolated ones; (2) the number of scent markings increased significantly with

46 CFR 169.755 - Draft marks and draft indicating systems.

Science.gov (United States)

2010-10-01

... Section 169.755 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) NAUTICAL SCHOOLS SAILING SCHOOL VESSELS Vessel Control, Miscellaneous Systems, and Equipment Markings § 169.755 Draft marks and... projections of the marks onto a vertical plane are of uniform height equal to the vertical spacing between...

An identification procedure for foodborne microbial hazards.

NARCIS (Netherlands)

Gerwen, van S.J.C.; Wit, de J.C.; Notermans, S.; Zwietering, M.H.

1997-01-01

A stepwise and interactive identification procedure for foodborne microbial hazards has been developed in which use is made of several levels of detail ranging from rough hazard identification to comprehensive hazard identification. This approach allows one to tackle the most obvious hazards first,

Avoiding the Hazards of Hazardous Waste.

Science.gov (United States)

Hiller, Richard

1996-01-01

Under a 1980 law, colleges and universities can be liable for cleanup of hazardous waste on properties, in companies, and related to stocks they invest in or are given. College planners should establish clear policy concerning gifts, investigate gifts, distance university from business purposes, sell real estate gifts quickly, consult a risk…

Toxic hazards of underground excavation

International Nuclear Information System (INIS)

Smith, R.; Chitnis, V.; Damasian, M.

1982-09-01

Inadvertent intrusion into natural or man-made toxic or hazardous material deposits as a consequence of activities such as mining, excavation or tunnelling has resulted in numerous deaths and injuries in this country. This study is a preliminary investigation to identify and document instances of such fatal or injurious intrusion. An objective is to provide useful insights and information related to potential hazards due to future intrusion into underground radioactive-waste-disposal facilities. The methodology used in this study includes literature review and correspondence with appropriate government agencies and organizations. Key categories of intrusion hazards are asphyxiation, methane, hydrogen sulfide, silica and asbestos, naturally occurring radionuclides, and various mine or waste dump related hazards

Toxic hazards of underground excavation

Energy Technology Data Exchange (ETDEWEB)

Smith, R.; Chitnis, V.; Damasian, M.; Lemm, M.; Popplesdorf, N.; Ryan, T.; Saban, C.; Cohen, J.; Smith, C.; Ciminesi, F.

1982-09-01

Inadvertent intrusion into natural or man-made toxic or hazardous material deposits as a consequence of activities such as mining, excavation or tunnelling has resulted in numerous deaths and injuries in this country. This study is a preliminary investigation to identify and document instances of such fatal or injurious intrusion. An objective is to provide useful insights and information related to potential hazards due to future intrusion into underground radioactive-waste-disposal facilities. The methodology used in this study includes literature review and correspondence with appropriate government agencies and organizations. Key categories of intrusion hazards are asphyxiation, methane, hydrogen sulfide, silica and asbestos, naturally occurring radionuclides, and various mine or waste dump related hazards.

Incidents with hazardous radiation sources

International Nuclear Information System (INIS)

Schoenhacker, Stefan

2016-01-01

Incidents with hazardous radiation sources can occur in any country, even those without nuclear facilities. Preparedness for such incidents is supposed to fulfill globally agreed minimum standards. Incidents are categorized in incidents with licensed handling of radiation sources as for material testing, transport accidents of hazardous radiation sources, incidents with radionuclide batteries, incidents with satellites containing radioactive inventory, incidents wit not licensed handling of illegally acquired hazardous radiation sources. The emergency planning in Austria includes a differentiation according to the consequences: incidents with release of radioactive materials resulting in restricted contamination, incidents with release of radioactive materials resulting in local contamination, and incidents with the hazard of e@nhanced exposure due to the radiation source.

9 CFR 592.320 - Products that may bear the inspection mark.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Products that may bear the inspection... Marking Products § 592.320 Products that may bear the inspection mark. Products that are permitted to bear... products eligible to bear the inspection mark and may contain other edible ingredients. The official mark...

27 CFR 20.33 - Time of destruction of marks and brands.

Science.gov (United States)

2010-04-01

... marks and brands. 20.33 Section 20.33 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND... Administrative Provisions Marks and Brands § 20.33 Time of destruction of marks and brands. (a) Any person who... alcohol or specially denatured rum shall immediately destroy or obliterate the marks, brands, and labels...

Ülar Mark: loome uut ja iga loomisega lammutame midagi / Ülar Mark ; intervjueerinud Mikk Salu

Index Scriptorium Estoniae

Mark, Ülar, 1968-

2010-01-01

Eesti Arhitektuurikeskuse juhatuse esimees, arhitekt Ülar Mark Tallinna arhitektuurist ja linna arengust, demokraatlikust linnaruumist. Pikemalt Solarise keskusest, vabadussambast, väikepoodide asemele suurte kaubanduskeskuste tulekust

Success in transmitting hazard science

Science.gov (United States)

Price, J. G.; Garside, T.

2010-12-01

Money motivates mitigation. An example of success in communicating scientific information about hazards, coupled with information about available money, is the follow-up action by local governments to actually mitigate. The Nevada Hazard Mitigation Planning Committee helps local governments prepare competitive proposals for federal funds to reduce risks from natural hazards. Composed of volunteers with expertise in emergency management, building standards, and earthquake, flood, and wildfire hazards, the committee advises the Nevada Division of Emergency Management on (1) the content of the State’s hazard mitigation plan and (2) projects that have been proposed by local governments and state agencies for funding from various post- and pre-disaster hazard mitigation programs of the Federal Emergency Management Agency. Local governments must have FEMA-approved hazard mitigation plans in place before they can receive this funding. The committee has been meeting quarterly with elected and appointed county officials, at their offices, to encourage them to update their mitigation plans and apply for this funding. We have settled on a format that includes the county’s giving the committee an overview of its infrastructure, hazards, and preparedness. The committee explains the process for applying for mitigation grants and presents the latest information that we have about earthquake hazards, including locations of nearby active faults, historical seismicity, geodetic strain, loss-estimation modeling, scenarios, and documents about what to do before, during, and after an earthquake. Much of the county-specific information is available on the web. The presentations have been well received, in part because the committee makes the effort to go to their communities, and in part because the committee is helping them attract federal funds for local mitigation of not only earthquake hazards but also floods (including canal breaches) and wildfires, the other major concerns in

7 CFR 319.37-10 - Marking and identity.

Science.gov (United States)

2010-01-01

... 7 Agriculture 5 2010-01-01 2010-01-01 false Marking and identity. 319.37-10 Section 319.37-10 Agriculture Regulations of the Department of Agriculture (Continued) ANIMAL AND PLANT HEALTH INSPECTION..., and Other Plant Products 1,2 § 319.37-10 Marking and identity. (a) Any restricted article for...

IDENTIFICATION OF AIRCRAFT HAZARDS

International Nuclear Information System (INIS)

K.L. Ashley

2005-01-01

Aircraft hazards were determined to be potentially applicable to a repository at Yucca Mountain in the ''Monitored Geological Repository External Events Hazards Screening Analysis'' (BSC 2004, Section 6.4.1). That determination was conservatively based on limited knowledge of flight data in the area of concern and on crash data for aircraft of the type flying near Yucca Mountain. The purpose of this report is to identify specific aircraft hazards that may be applicable to a Monitored Geologic Repository (MGR) at Yucca Mountain using NUREG-0800, ''Standard Review Plan for the Review of Safety Analysis Reports for Nuclear Power Plants'' (NRC 1987, Section 3.5.1.6), as guidance for the inclusion or exclusion of identified aircraft hazards. NUREG-0800 is being used here as a reference because some of the same considerations apply. The intended use of this report is to provide inputs for further screening and analysis of the identified aircraft hazards based on the criteria that apply to Category 1 and 2 event sequence analyses as defined in 10 CFR 63.2 (see Section 4). The scope of this technical report includes the evaluation of military, private, and commercial use of airspace in the 100-mile regional setting of the MGR at Yucca Mountain with the potential for reducing the regional setting to a more manageable size after consideration of applicable screening criteria (see Section 7)

Identification of Aircraft Hazards

Energy Technology Data Exchange (ETDEWEB)

K. Ashley

2006-12-08

Aircraft hazards were determined to be potentially applicable to a repository at Yucca Mountain in ''Monitored Geological Repository External Events Hazards Screening Analysis'' (BSC 2005 [DIRS 174235], Section 6.4.1). That determination was conservatively based upon limited knowledge of flight data in the area of concern and upon crash data for aircraft of the type flying near Yucca Mountain. The purpose of this report is to identify specific aircraft hazards that may be applicable to a monitored geologic repository (MGR) at Yucca Mountain, using NUREG-0800, ''Standard Review Plan for the Review of Safety Analysis Reports for Nuclear Power Plants'' (NRC 1987 [DIRS 103124], Section 3.5.1.6), as guidance for the inclusion or exclusion of identified aircraft hazards. The intended use of this report is to provide inputs for further screening and analysis of identified aircraft hazards based upon the criteria that apply to Category 1 and Category 2 event sequence analyses as defined in 10 CFR 63.2 [DIRS 176544] (Section 4). The scope of this report includes the evaluation of military, private, and commercial use of airspace in the 100-mile regional setting of the repository at Yucca Mountain with the potential for reducing the regional setting to a more manageable size after consideration of applicable screening criteria (Section 7).

46 CFR 167.55-1 - Draft marks and draft indicating systems.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Draft marks and draft indicating systems. 167.55-1... NAUTICAL SCHOOL SHIPS Special Markings Required § 167.55-1 Draft marks and draft indicating systems. (a... aft to the location of the draft marks, due to a raked stem or cut away skeg, the draft must be...

Tense Marking in the English Narrative Retells of Dual Language Preschoolers.

Science.gov (United States)

Gusewski, Svenja; Rojas, Raúl

2017-07-26

This longitudinal study investigated the emergence of English tense marking in young (Spanish-English) dual language learners (DLLs) over 4 consecutive academic semesters, addressing the need for longitudinal data on typical acquisition trajectories of English in DLL preschoolers. Language sample analysis was conducted on 139 English narrative retells elicited from 39 preschool-age (Spanish-English) DLLs (range = 39-65 months). Growth curve models captured within- and between-individual change in tense-marking accuracy over time. Tense-marking accuracy was indexed by the finite verb morphology composite and by 2 specifically developed adaptations. Individual tense markers were systematically described in terms of overall accuracy and specific error patterns. Tense-marking accuracy exhibited significant growth over time for each composite. Initially, irregular past-tense accuracy was higher than regular past-tense accuracy; over time, however, regular past-tense marking outpaced accuracy on irregular verbs. These findings suggest that young DLLs can achieve high tense-marking accuracy assuming 2 years of immersive exposure to English. Monitoring the growth in tense-marking accuracy over time and considering productive tense-marking errors as partially correct more precisely captured the emergence of English tense marking in this population with highly variable expressive language skills. https://doi.org/10.23641/asha.5176942.

A Model for Generating Multi-hazard Scenarios

Science.gov (United States)

Lo Jacomo, A.; Han, D.; Champneys, A.

2017-12-01

Communities in mountain areas are often subject to risk from multiple hazards, such as earthquakes, landslides, and floods. Each hazard has its own different rate of onset, duration, and return period. Multiple hazards tend to complicate the combined risk due to their interactions. Prioritising interventions for minimising risk in this context is challenging. We developed a probabilistic multi-hazard model to help inform decision making in multi-hazard areas. The model is applied to a case study region in the Sichuan province in China, using information from satellite imagery and in-situ data. The model is not intended as a predictive model, but rather as a tool which takes stakeholder input and can be used to explore plausible hazard scenarios over time. By using a Monte Carlo framework and varrying uncertain parameters for each of the hazards, the model can be used to explore the effect of different mitigation interventions aimed at reducing the disaster risk within an uncertain hazard context.

Reviewing and visualizing the interactions of natural hazards

Science.gov (United States)

Gill, Joel C.; Malamud, Bruce D.

2014-12-01

This paper presents a broad overview, characterization, and visualization of the interaction relationships between 21 natural hazards, drawn from six hazard groups (geophysical, hydrological, shallow Earth, atmospheric, biophysical, and space hazards). A synthesis is presented of the identified interaction relationships between these hazards, using an accessible visual format particularly suited to end users. Interactions considered are primarily those where a primary hazard triggers or increases the probability of secondary hazards occurring. In this paper we do the following: (i) identify, through a wide-ranging review of grey- and peer-review literature, 90 interactions; (ii) subdivide the interactions into three levels, based on how well we can characterize secondary hazards, given information about the primary hazard; (iii) determine the spatial overlap and temporal likelihood of the triggering relationships occurring; and (iv) examine the relationship between primary and secondary hazard intensities for each identified hazard interaction and group these into five possible categories. In this study we have synthesized, using accessible visualization techniques, large amounts of information drawn from many scientific disciplines. We outline the importance of constraining hazard interactions and reinforce the importance of a holistic (or multihazard) approach to natural hazard assessment. This approach allows those undertaking research into single hazards to place their work within the context of other hazards. It also communicates important aspects of hazard interactions, facilitating an effective analysis by those working on reducing and managing disaster risk within both the policy and practitioner communities.

The Nature of Natural Hazards Communication (Invited)

Science.gov (United States)

Kontar, Y. Y.

2013-12-01

Some of the many issues of interest to natural hazards professionals include the analysis of proactive approaches to the governance of risk from natural hazards and approaches to broaden the scope of public policies related to the management of risks from natural hazards, as well as including emergency and environmental management, community development and spatial planning related to natural hazards. During the talk we will present results of scientific review, analysis and synthesis, which emphasize same new trends in communication of the natural hazards theories and practices within an up-to-the-minute context of new environmental and climate change issues, new technologies, and a new focus on resiliency. The presentation is divided into five sections that focus on natural hazards communication in terms of education, risk management, public discourse, engaging the public, theoretical perspectives, and new media. It includes results of case studies and best practices. It delves into natural hazards communication theories, including diffusion, argumentation, and constructivism, to name a few. The presentation will provide information about: (1) A manual of natural hazards communication for scientists, policymakers, and media; (2) An up-to-the-minute context of environmental hazards, new technologies & political landscape; (3) A work by natural hazards scientists for geoscientists working with social scientists and communication principles; (4) A work underpinned by key natural hazards communication theories and interspersed with pragmatic solutions; (5) A work that crosses traditional natural hazards boundaries: international, interdisciplinary, theoretical/applied. We will further explore how spatial planning can contribute to risk governance by influencing the occupation of natural hazard-prone areas, and review the central role of emergency management in risk policy. The goal of this presentation is to contribute to the augmentation of the conceptual framework

Probabilistic seismic hazard assessment. Gentilly 2

International Nuclear Information System (INIS)

1996-03-01

Results of this probabilistic seismic hazard assessment were determined using a suite of conservative assumptions. The intent of this study was to perform a limited hazard assessment that incorporated a range of technically defensible input parameters. To best achieve this goal, input selected for the hazard assessment tended to be conservative with respect to selection of attenuation modes, and seismicity parameters. Seismic hazard estimates at Gentilly 2 were most affected by selection of the attenuation model. Alternative definitions of seismic source zones had a relatively small impact on seismic hazard. A St. Lawrence Rift model including a maximum magnitude of 7.2 m b in the zone containing the site had little effect on the hazard estimate relative to other seismic source zonation models. Mean annual probabilities of exceeding the design peak ground acceleration, and the design response spectrum for the Gentilly 2 site were computed to lie in the range of 0.001 to 0.0001. This hazard result falls well within the range determined to be acceptable for nuclear reactor sites located throughout the eastern United States. (author) 34 refs., 6 tabs., 28 figs

Report 6: Guidance document. Man-made hazards and Accidental Aircraft Crash hazards modelling and implementation in extended PSA

International Nuclear Information System (INIS)

Kahia, S.; Brinkman, H.; Bareith, A.; Siklossy, T.; Vinot, T.; Mateescu, T.; Espargilliere, J.; Burgazzi, L.; Ivanov, I.; Bogdanov, D.; Groudev, P.; Ostapchuk, S.; Zhabin, O.; Stojka, T.; Alzbutas, R.; Kumar, M.; Nitoi, M.; Farcasiu, M.; Borysiewicz, M.; Kowal, K.; Potempski, S.

2016-01-01

The goal of this report is to provide guidance on practices to model man-made hazards (mainly external fires and explosions) and accidental aircraft crash hazards and implement them in extended Level 1 PSA. This report is a joint deliverable of work package 21 (WP21) and work package 22 (WP22). The general objective of WP21 is to provide guidance on all of the individual hazards selected at the first ASAMPSA-E End Users Workshop (May 2014, Uppsala, Sweden). The objective of WP22 is to provide the solutions for purposes of different parts of man-made hazards Level 1 PSA fulfilment. This guidance is focusing on man-made hazards, namely: external fires and explosions, and accidental aircraft crash hazards. Guidance developed refers to existing guidance whenever possible. The initial part of guidance (WP21 part) reflects current practices to assess the frequencies for each type of hazards or combination of hazards (including correlated hazards) as initiating event for PSAs. The sources and quality of hazard data, the elements of hazard assessment methodologies and relevant examples are discussed. Classification and criteria to properly assess hazard combinations as well as examples and methods for assessment of these combinations are included in this guidance. In appendixes additional material is presented with the examples of practical approaches to aircraft crash and man-made hazard. The following issues are addressed: 1) Hazard assessment methodologies, including issues related to hazard combinations. 2) Modelling equipment of safety related SSC, 3) HRA, 4) Emergency response, 5) Multi-unit issues. Recommendations and also limitations, gaps identified in the existing methodologies and a list of open issues are included. At all stages of this guidance and especially from an industrial end-user perspective, one must keep in mind that the development of man-made hazards probabilistic analysis must be conditioned to the ability to ultimately obtain a representative risk

Canister storage building hazard analysis report

International Nuclear Information System (INIS)

POWERS, T.B.

1999-01-01

This report describes the methodology used in conducting the Canister Storage Building (CSB) hazard analysis to support the CSB final safety analysis report (FSAR) and documents the results. The hazard analysis was performed in accordance with the DOE-STD-3009-94, ''Preparation Guide for US. Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports'', and meets the intent of HNF-PRO-704, ''Hazard and Accident Analysis Process''. This hazard analysis implements the requirements of DOE Order 5480.23, ''Nuclear Safety Analysis Reports''

Multi-Disciplinary Peer-Mark Moderation of Group Work

Science.gov (United States)

Willmot, Peter; Pond, Keith

2012-01-01

Self and peer assessment offers benefits for enhancing student learning. Peer moderation provides a convenient solution for awarding individual marks in group assignments. This paper provides a significant review of peer-mark moderation, and describes an award winning, web-based tool that was developed in the UK and is now spreading across the…

Mechanisms for Limiting Trade Mark Rights to Further Competition and Free Speech

DEFF Research Database (Denmark)

Ramsey, Lisa P; Schovsbo, Jens Hemmingsen

2013-01-01

This article evaluates the different mechanisms that nations use to limit trade mark rights to promote competition, free speech, and other public interests. It shows how EU and US trade mark laws seem to be converging towards a similar model which includes both (1) specific statutory defenses...... of these mechanisms for limiting trade mark rights to better protect the public interest in trade mark disputes. Finally, a proposal for reform is suggested. It consists of three parts: (1) domestic legislatures should revise their trade mark statutes to add more mandatory and specific limitations on trade mark...... to trade mark violations and (2) trade mark doctrines which give courts flexibility to permit unauthorized uses of marks that further the legitimate interests of the accused infringer and the public. Such a development should be welcomed and the article urges other nations to consider adopting one or both...

LAV@HAZARD: a Web-GIS Framework for Real-Time Forecasting of Lava Flow Hazards

Science.gov (United States)

Del Negro, C.; Bilotta, G.; Cappello, A.; Ganci, G.; Herault, A.

2014-12-01

Crucial to lava flow hazard assessment is the development of tools for real-time prediction of flow paths, flow advance rates, and final flow lengths. Accurate prediction of flow paths and advance rates requires not only rapid assessment of eruption conditions (especially effusion rate) but also improved models of lava flow emplacement. Here we present the LAV@HAZARD web-GIS framework, which combines spaceborne remote sensing techniques and numerical simulations for real-time forecasting of lava flow hazards. By using satellite-derived discharge rates to drive a lava flow emplacement model, LAV@HAZARD allows timely definition of parameters and maps essential for hazard assessment, including the propagation time of lava flows and the maximum run-out distance. We take advantage of the flexibility of the HOTSAT thermal monitoring system to process satellite images coming from sensors with different spatial, temporal and spectral resolutions. HOTSAT was designed to ingest infrared satellite data acquired by the MODIS and SEVIRI sensors to output hot spot location, lava thermal flux and discharge rate. We use LAV@HAZARD to merge this output with the MAGFLOW physics-based model to simulate lava flow paths and to update, in a timely manner, flow simulations. Thus, any significant changes in lava discharge rate are included in the predictions. A significant benefit in terms of computational speed was obtained thanks to the parallel implementation of MAGFLOW on graphic processing units (GPUs). All this useful information has been gathered into the LAV@HAZARD platform which, due to the high degree of interactivity, allows generation of easily readable maps and a fast way to explore alternative scenarios. We will describe and demonstrate the operation of this framework using a variety of case studies pertaining to Mt Etna, Sicily. Although this study was conducted on Mt Etna, the approach used is designed to be applicable to other volcanic areas around the world.

Portable sensor for hazardous waste

International Nuclear Information System (INIS)

Piper, L.G.

1994-01-01

Objective was to develop a field-portable monitor for sensitive hazardous waste detection using active nitrogen energy transfer (ANET) excitation of atomic and molecular fluorescence (active nitrogen is made in a dielectric-barrier discharge in nitrogen). It should provide rapid field screening of hazardous waste sites to map areas of greatest contamination. Results indicate that ANET is very sensitive for monitoring heavy metals (Hg, Se) and hydrocarbons; furthermore, chlorinated hydrocarbons can be distinguished from nonchlorinated ones. Sensitivity is at ppB levels for sampling in air. ANET appears ideal for on-line monitoring of toxic heavy metal levels at building sites, hazardous waste land fills, in combustor flues, and of chlorinated hydrocarbon levels at building sites and hazardous waste dumps

Portable sensor for hazardous waste

Energy Technology Data Exchange (ETDEWEB)

Piper, L.G.; Fraser, M.E.; Davis, S.J. [Physical Sciences Inc., Andover, MA (United States)

1995-10-01

We are beginning the second phase of a three and a half year program designed to develop a portable monitor for sensitive hazardous waste detection. The ultimate goal of the program is to develop our concept to the prototype instrument level. Our monitor will be a compact, portable instrument that will allow real-time, in situ, monitoring of hazardous wastes. This instrument will be able to provide the means for rapid field screening of hazardous waste sites to map the areas of greatest contamination. Remediation efforts can then focus on these areas. Further, our instrument can show whether cleanup technologies are successful at reducing hazardous materials concentrations below regulated levels, and will provide feedback to allow changes in remediation operations, if necessary, to enhance their efficacy.

46 CFR 151.03-30 - Hazardous material.

Science.gov (United States)

2010-10-01

... hazardous material means a liquid material or substance that is— (a) Flammable or combustible; (b) Designated a hazardous substance under section 311(b) of the Federal Water Pollution Control Act (33 U.S.C... Agency designates hazardous substances in 40 CFR Table 116.4A. The Coast Guard designates hazardous...

Scent marking behavior as an odorant communication in mice

Science.gov (United States)

Arakawa, Hiroyuki; Blanchard, D. Caroline; Arakawa, Keiko; Dunlap, Christopher; Blanchard, Robert J.

2008-01-01

In rodents, where chemical signals play a particularly important role in determining intraspecies interactions including social dominance and intersexual relationships, various studies have shown that behavior is sensitive to conspecific odor cues. Mice use urinary scent marks for communication with individual conspecifics in many social contexts. Urinary scent involves genetic information about individuals such as species, sex, and individual identity as well as metabolic information such as social dominance, and reproductive and health status, which are mediated by chemical proteins in scent marks including the major histocompatibility complex and the major urinary proteins. The odor of the predator which can be considered to be a threatening signal for the prey also modulate mouse behavior in which scent marking is suppressed in response to the cat odor exposure in mice. These odorant chemicals are detected and recognized through two olfactory bulbs, the role of which in detection of chemosignals with biological relevant appears to be differential, but partly overlapped. Mice deposit scent marks toward conspecifics to maintain their social relationships, and inhibit scent marking in a context where natural predator, cat odor is contained. This suppression of scent marking is long-lasting (for at least 7 days) and context-dependent, while the odorant signaling to conspecifics tends to appear frequently (over 24 hrs but less than 7 days intervals) depending on the familiarity of each signal-recipient. It has been discussed that scent marking is a communicative behavior associated with territoriality toward conspecifics, indicating that the social signaling within species are sensitive to predator odor cues in terms of vulnerability to predation risk. PMID:18565582

FEMA DFIRM Flood Hazard Areas

Data.gov (United States)

Minnesota Department of Natural Resources — FEMA flood hazard delineations are used by the Federal Emergency Management Agency (FEMA) to designate the Special Flood Hazard Area (SFHA) and for insurance rating...

Hazardous Waste: Learn the Basics of Hazardous Waste

Science.gov (United States)

... Need More Information on Hazardous Waste? The RCRA Orientation Manual provides introductory information on the solid and ... and Security Notice Connect. Data.gov Inspector General Jobs Newsroom Open Government Regulations.gov Subscribe USA.gov ...

14 CFR 437.55 - Hazard analysis.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Hazard analysis. 437.55 Section 437.55... TRANSPORTATION LICENSING EXPERIMENTAL PERMITS Safety Requirements § 437.55 Hazard analysis. (a) A permittee must... safety of property resulting from each permitted flight. This hazard analysis must— (1) Identify and...

Preliminary Hazard Classification for the 105-B Reactor

International Nuclear Information System (INIS)

Kerr, N.R.

1997-08-01

This document summarizes the inventories of radioactive and hazardous materials present within the 105-B Reactor and uses the inventory information to determine the preliminary hazard classification for the surveillance and maintenance activities of the facility. The result of this effort was the preliminary hazard classification for the 105-B Building surveillance and maintenance activities. The preliminary hazard classification was determined to be Nuclear Category 3. Additional hazard and accident analysis will be documented in a separate report to define the hazard controls and final hazard classification

27 CFR 26.106 - Marking containers of beer.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Marking containers of beer... Liquors and Articles in Puerto Rico Beer § 26.106 Marking containers of beer. Containers of beer of Puerto... brewer; the serial number, capacity, and size of the container; the kind of beer; and the serial number...

27 CFR 26.97 - Marking containers of wine.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Marking containers of wine... Liquors and Articles in Puerto Rico Wine § 26.97 Marking containers of wine. Containers of wine of Puerto... winemaker, the serial number of the container, the kind and taxable grade of the wine, the gallon content...

Hazardous waste management in research laboratories

International Nuclear Information System (INIS)

Sundstrom, G.

1989-01-01

Hazardous waste management in research laboratories benefits from a fundamentally different approach to the hazardous waste determination from industry's. This paper introduces new, statue-based criteria for identifying hazardous wastes (such as radiological mixed wastes and waste oils) and links them to a forward-looking compliance of laboratories, the overall system integrates hazardous waste management activities with other environmental and hazard communication initiatives. It is generalizable to other waste generators, including industry. Although only the waste identification and classification aspects of the system are outlined in detail here, four other components are defined or supported, namely: routine and contingency practices; waste treatment/disposal option definition and selection; waste minimization, recycling, reuse, and substitution opportunities; and key interfaces with other systems, including pollution prevention

BEHAVIORAL HAZARD IN HEALTH INSURANCE*

Science.gov (United States)

Baicker, Katherine; Mullainathan, Sendhil; Schwartzstein, Joshua

2015-01-01

A fundamental implication of standard moral hazard models is overuse of low-value medical care because copays are lower than costs. In these models, the demand curve alone can be used to make welfare statements, a fact relied on by much empirical work. There is ample evidence, though, that people misuse care for a different reason: mistakes, or “behavioral hazard.” Much high-value care is underused even when patient costs are low, and some useless care is bought even when patients face the full cost. In the presence of behavioral hazard, welfare calculations using only the demand curve can be off by orders of magnitude or even be the wrong sign. We derive optimal copay formulas that incorporate both moral and behavioral hazard, providing a theoretical foundation for value-based insurance design and a way to interpret behavioral “nudges.” Once behavioral hazard is taken into account, health insurance can do more than just provide financial protection—it can also improve health care efficiency. PMID:23930294

Hazard avoidance via descent images for safe landing

Science.gov (United States)

Yan, Ruicheng; Cao, Zhiguo; Zhu, Lei; Fang, Zhiwen

2013-10-01

In planetary or lunar landing missions, hazard avoidance is critical for landing safety. Therefore, it is very important to correctly detect hazards and effectively find a safe landing area during the last stage of descent. In this paper, we propose a passive sensing based HDA (hazard detection and avoidance) approach via descent images to lower the landing risk. In hazard detection stage, a statistical probability model on the basis of the hazard similarity is adopted to evaluate the image and detect hazardous areas, so that a binary hazard image can be generated. Afterwards, a safety coefficient, which jointly utilized the proportion of hazards in the local region and the inside hazard distribution, is proposed to find potential regions with less hazards in the binary hazard image. By using the safety coefficient in a coarse-to-fine procedure and combining it with the local ISD (intensity standard deviation) measure, the safe landing area is determined. The algorithm is evaluated and verified with many simulated descent downward looking images rendered from lunar orbital satellite images.

Mirror-mark tests performed on jackdaws reveal potential methodological problems in the use of stickers in avian mark-test studies.

Directory of Open Access Journals (Sweden)

Manuel Soler

Full Text Available Some animals are capable of recognizing themselves in a mirror, which is considered to be demonstrated by passing the mark test. Mirror self-recognition capacity has been found in just a few mammals having very large brains and only in one bird, the magpie (Pica pica. The results obtained in magpies have enormous biological and cognitive implications because the fact that magpies were able to pass the mark test meant that this species is at the same cognitive level with great apes, that mirror self-recognition has evolved independently in the magpie and great apes (which diverged 300 million years ago, and that the neocortex (which is not present in the bird's brains is not a prerequisite for mirror self-recognition as previously believed. Here, we have replicated the experimental design used on magpies to determine whether jackdaws (Corvus monedula are also capable of mirror self-recognition by passing the mark test. We found that our nine jackdaws showed a very high interest towards the mirror and exhibited self-contingent behavior as soon as mirrors were introduced. However, jackdaws were not able to pass the mark test: both sticker-directed actions and sticker removal were performed with a similar frequency in both the cardboard (control and the mirror conditions. We conclude that our jackdaws' behaviour raises non-trivial questions about the methodology used in the avian mark test. Our study suggests that the use of self-adhesive stickers on sensitive throat feathers may open the way to artefactual results because birds might perceive the stickers tactilely.

Aksel Mark: kõik algaski Otsal / Enn Nõu

Index Scriptorium Estoniae

Nõu, Enn, 1933-

2012-01-01

Arvustus: Mark Beijer, Mai. Landkänning : Brevväxling mellan Anu och Aksel Mark under deras första år som flyktingar från Estland 1944-45. Stockholm : Bokverksta´n Förlag, 2008; Allt började på Otsa : minnen från min barndom och skoláren. Stockholm : Beijer Bok & Skog, 2011

Object marking in Swahili: Definiteness, specificity, or both ...

African Journals Online (AJOL)

This article examines the role of object marking in relation to definiteness and specificity in Swahili. Object marking in general has attracted the attention of many scholars in the field of Bantu linguistics due to the complex nature of object markers (OMs) and varying functions they fulfil in Bantu. Opinions differ on the role of ...

Hazardous waste management in the Pacific basin

Energy Technology Data Exchange (ETDEWEB)

Cirillo, R.R.; Chiu, S.; Chun, K.C.; Conzelmann, G. [Argonne National Lab., IL (United States); Carpenter, R.A.; Indriyanto, S.H. [East-West Center, Honolulu, HI (United States)

1994-11-01

Hazardous waste control activities in Asia and the Pacific have been reviewed. The review includes China (mainland, Hong Kong, and Taiwan), Indonesia, Korea, Malaysia, Papua New Guinea, the Philippines, Singapore, and Thailand. It covers the sources of hazardous waste, the government structure for dealing with hazardous waste, and current hazardous waste control activities in each country. In addition, the hazardous waste program activities of US government agencies, US private-sector organizations, and international organizations are reviewed. The objective of these reviews is to provide a comprehensive picture of the current hazardous waste problems and the waste management approaches being used to address them so that new program activities can be designed more efficiently.

Mark Leonard : EL ei peakski olema suurvõim / Mark Leonard ; interv. Erkki Bahovski

Index Scriptorium Estoniae

Leonard, Mark

2008-01-01

Intervjuu Euroopa Välissuhete Nõukogu tegevdirektoriga, kes vastab küsimustele, mis puudutavad USA ja Euroopa suhteid, Euroopa Liidu välispoliitikat, Venemaa ja Euroopa Liidu suhteid pärast Gruusia konflikti. Ta peab murettekitavaks, et Venemaa üritab takistada euroopalike väärtuste levitamist oma naaberriikides. Vt. samas: Mark Leonard. Ilmunud ka Sirp : Diplomaatia 14. nov. nr. 11 lk. 13-14

Travelers' Health: Animal-Associated Hazards

Science.gov (United States)

... Chapter 2 - Safety & Security Chapter 2 - Environmental Hazards Animal-Associated Hazards Heather Bair-Brake, Ryan M. Wallace, G. Gale Galland, Nina Marano HUMAN INTERACTION WITH ANIMALS: A RISK FACTOR FOR INJURY AND ILLNESS Animals, ...

21 CFR 120.7 - Hazard analysis.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Hazard analysis. 120.7 Section 120.7 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN... hazards. The written hazard analysis shall consist of at least the following: (1) Identification of food...

Leaching behaviour of hazardous waste under the impact of different ambient conditions.

Science.gov (United States)

Pecorini, Isabella; Baldi, Francesco; Bacchi, Donata; Carnevale, Ennio Antonio; Corti, Andrea

2017-05-01

The overall objective of this study is to provide an improved basis for the assessment of the leaching behaviour of waste marked as hazardous partly stabilised (European waste catalogue code 19 03 04 ∗ ). Four samples of hazardous partly stabilised waste were subjected to two leaching tests: up-flow column tests and batch equilibrium tests. The research was carried out in two directions: the first aims at comparing the results of the two experimental setups while the second aims at assessing the impact of different ambient conditions on the leaching behaviour of waste. Concerning this latter objective the effect of mesophilic temperature, mechanical constraints and acid environment were tested through column percolation tests. Results showed no significant differences between batch and column leaching test outcomes when comparing average concentrations calculated at a liquid to solid ratio of 10:1 l kg -1  TS. Among the tested ambient conditions, the presence of an acid environment (pH=4.5) accelerated the leaching process resulting in a higher cumulative released quantity measured on the majority of the investigated polluting substances. On the contrary, the effect of temperature and mechanical constraints seemed to not affect the process showing final contents even lower than values found for the standard test. This result was furthermore confirmed by the application of the principal component analysis. Copyright © 2016 Elsevier Ltd. All rights reserved.

Sustainable System for Residual Hazards Management

International Nuclear Information System (INIS)

Kevin M. Kostelnik; James H. Clarke; Jerry L. Harbour

2004-01-01

Hazardous, radioactive and other toxic substances have routinely been generated and subsequently disposed of in the shallow subsurface throughout the world. Many of today's waste management techniques do not eliminate the problem, but rather only concentrate or contain the hazardous contaminants. Residual hazards result from the presence of hazardous and/or contaminated material that remains on-site following active operations or the completion of remedial actions. Residual hazards pose continued risk to humans and the environment and represent a significant and chronic problem that require continuous long-term management (i.e. >1000 years). To protect human health and safeguard the natural environment, a sustainable system is required for the proper management of residual hazards. A sustainable system for the management of residual hazards will require the integration of engineered, institutional and land-use controls to isolate residual contaminants and thus minimize the associated hazards. Engineered controls are physical modifications to the natural setting and ecosystem, including the site, facility, and/or the residual materials themselves, in order to reduce or eliminate the potential for exposure to contaminants of concern (COCs). Institutional controls are processes, instruments, and mechanisms designed to influence human behavior and activity. System failure can involve hazardous material escaping from the confinement because of system degradation (i.e., chronic or acute degradation) or by external intrusion of the biosphere into the contaminated material because of the loss of institutional control. An ongoing analysis of contemporary and historic sites suggests that the significance of the loss of institutional controls is a critical pathway because decisions made during the operations/remedial action phase, as well as decisions made throughout the residual hazards management period, are key to the long-term success of the prescribed system. In fact

Controlling organic chemical hazards in food manufacturing: a hazard analysis critical control points (HACCP) approach.

Science.gov (United States)

Ropkins, K; Beck, A J

2002-08-01

Hazard analysis by critical control points (HACCP) is a systematic approach to the identification, assessment and control of hazards. Effective HACCP requires the consideration of all hazards, i.e., chemical, microbiological and physical. However, to-date most 'in-place' HACCP procedures have tended to focus on the control of microbiological and physical food hazards. In general, the chemical component of HACCP procedures is either ignored or limited to applied chemicals, e.g., food additives and pesticides. In this paper we discuss the application of HACCP to a broader range of chemical hazards, using organic chemical contaminants as examples, and the problems that are likely to arise in the food manufacturing sector. Chemical HACCP procedures are likely to result in many of the advantages previously identified for microbiological HACCP procedures: more effective, efficient and economical than conventional end-point-testing methods. However, the high costs of analytical monitoring of chemical contaminants and a limited understanding of formulation and process optimisation as means of controlling chemical contamination of foods are likely to prevent chemical HACCP becoming as effective as microbiological HACCP.

A new relative hazard index

International Nuclear Information System (INIS)

Smith, C.F.; Burnett, T.W.T; Kastenberg, W.E.

1976-01-01

Several indexes for the evaluation of relative radionuclide hazards have been previously developed. In this paper, a new relative hazard index is derived for use in the assessment of the future burden to mankind from the presence of radionuclides in the environment. Important features of this hazard index are that it takes into account multiple decay schemes, non-equilibrium conditions, and finite time periods. As an application of this hazard index, a comparison is made between thermal reactor radioactive waste and the uranium required as fuel with the following conclusions: (1) For short time intervals (d 234 U breaking the uranium decay chain. (3) For long time intervals of concern (d >= 500 000 years), the reactor waste and consumed uranium indexes are equal after a much shorter decay time (approximately 10 years.) (author)

Application of the Coastal Hazard Wheel methodology for coastal multi-hazard assessment and management in the state of Djibouti

Directory of Open Access Journals (Sweden)

Lars Rosendahl Appelquist

2014-01-01

Full Text Available This paper presents the application of a new methodology for coastal multi-hazard assessment and management in a changing global climate on the state of Djibouti. The methodology termed the Coastal Hazard Wheel (CHW is developed for worldwide application and is based on a specially designed coastal classification system that incorporates the main static and dynamic parameters determining the characteristics of a coastal environment. The methodology provides information on the hazards of ecosystem disruption, gradual inundation, salt water intrusion, erosion and flooding and can be used to support management decisions at local, regional and national level, in areas with limited access to geophysical data. The assessment for Djibouti applies a geographic information system (GIS to develop a range of national hazard maps along with relevant hazard statistics and is showcasing the procedure for applying the CHW methodology for national hazard assessments. The assessment shows that the coastline of Djibouti is characterized by extensive stretches with high or very high hazards of ecosystem disruption, mainly related to coral reefs and mangrove forests, while large sections along the coastlines of especially northern and southern Djibouti have high hazard levels for gradual inundation. The hazard of salt water intrusion is moderate along most of Djibouti’s coastline, although groundwater availability is considered to be very sensitive to human ground water extraction. High or very high erosion hazards are associated with Djibouti’s sedimentary plains, estuaries and river mouths, while very high flooding hazards are associated with the dry river mouths.

Hazard Communication Guidelines for Compliance

National Research Council Canada - National Science Library

2000-01-01

OSHA's Hazard Communication Standard (HCS) is based on a simple concept that employees have both a need and a right to know the hazards and identities of the chemicals they are exposed to when working...

Hazards assessment for the INEL Landfill Complex

International Nuclear Information System (INIS)

Knudsen, J.K.; Calley, M.B.

1994-02-01

This report documents the hazards assessment for the INEL Landfill Complex (LC) located at the Idaho National Engineering Laboratory, which is operated by EG ampersand G Idaho, Inc., for the US Department of Energy (DOE). The hazards assessment was performed to ensure that this facility complies with DOE and company requirements pertaining to emergency planning and preparedness for operational emergencies. DOE Order 5500.3A requires that a facility-specific hazards assessment be performed to provide the technical basis for facility emergency planning efforts. This hazards assessment was conducted in accordance with DOE Headquarters and the DOE Idaho Operations Office (DOE-ID) guidance to comply with DOE Order 5500.3A. The hazards assessment identifies and analyzes the hazards that are significant enough to warrant consideration in a facility's operational emergency management program. The area surrounding the LC, the buildings and structures at the LC, and the processes that are used at the LC are described in this report. All hazardous materials, both radiological and nonradiological, at the LC were identified and screened against threshold quantities according to DOE Order 5500.3A guidance. Asbestos at the Asbestos Pit was the only hazardous material that exceeded its specified threshold quantity. However, the type of asbestos received and the packaging practices used are believed to limit the potential for an airborne release of asbestos fibers. Therefore, in accordance with DOE Order 5500.3A guidance, no further hazardous material characterization or analysis was required for this hazards assessment

Hazards assessment for the INEL Landfill Complex

Energy Technology Data Exchange (ETDEWEB)

Knudsen, J.K.; Calley, M.B.

1994-02-01

This report documents the hazards assessment for the INEL Landfill Complex (LC) located at the Idaho National Engineering Laboratory, which is operated by EG&G Idaho, Inc., for the US Department of Energy (DOE). The hazards assessment was performed to ensure that this facility complies with DOE and company requirements pertaining to emergency planning and preparedness for operational emergencies. DOE Order 5500.3A requires that a facility-specific hazards assessment be performed to provide the technical basis for facility emergency planning efforts. This hazards assessment was conducted in accordance with DOE Headquarters and the DOE Idaho Operations Office (DOE-ID) guidance to comply with DOE Order 5500.3A. The hazards assessment identifies and analyzes the hazards that are significant enough to warrant consideration in a facility`s operational emergency management program. The area surrounding the LC, the buildings and structures at the LC, and the processes that are used at the LC are described in this report. All hazardous materials, both radiological and nonradiological, at the LC were identified and screened against threshold quantities according to DOE Order 5500.3A guidance. Asbestos at the Asbestos Pit was the only hazardous material that exceeded its specified threshold quantity. However, the type of asbestos received and the packaging practices used are believed to limit the potential for an airborne release of asbestos fibers. Therefore, in accordance with DOE Order 5500.3A guidance, no further hazardous material characterization or analysis was required for this hazards assessment.

Reproducibility of Computer-Aided Detection Marks in Digital Mammography

International Nuclear Information System (INIS)

Kim, Seung Ja; Moon, Woo Kyung; Cho, Nariya; Kim, Sun Mi; Im, Jung Gi; Cha, Joo Hee

2007-01-01

To evaluate the performance and reproducibility of a computeraided detection (CAD) system in mediolateral oblique (MLO) digital mammograms taken serially, without release of breast compression. A CAD system was applied preoperatively to the fulfilled digital mammograms of two MLO views taken without release of breast compression in 82 patients (age range: 33 83 years; mean age: 49 years) with previously diagnosed breast cancers. The total number of visible lesion components in 82 patients was 101: 66 masses and 35 microcalcifications. We analyzed the sensitivity and reproducibility of the CAD marks. The sensitivity of the CAD system for first MLO views was 71% (47/66) for masses and 80% (28/35) for microcalcifications. The sensitivity of the CAD system for second MLO views was 68% (45/66) for masses and 17% (6/35) for microcalcifications. In 84 ipsilateral serial MLO image sets (two patients had bilateral cancers), identical images, regardless of the existence of CAD marks, were obtained for 35% (29/84) and identical images with CAD marks were obtained for 29% (23/78). Identical images, regardless of the existence of CAD marks, for contralateral MLO images were 65% (52/80) and identical images with CAD marks were obtained for 28% (11/39). The reproducibility of CAD marks for the true positive masses in serial MLO views was 84% (42/50) and that for the true positive microcalcifications was 0% (0/34). The CAD system in digital mammograms showed a high sensitivity for detecting masses and microcalcifications. However, reproducibility of microcalcification marks was very low in MLO views taken serially without release of breast compression. Minute positional change and patient movement can alter the images and result in a significant effect on the algorithm utilized by the CAD for detecting microcalcifications

Amoralist rationalism? A response to Joel Marks: commentary on "Animal abolitionism meets moral abolitionism: cutting the Gordian knot of applied ethics" by Joel Marks.

Science.gov (United States)

Lederman, Zohar

2014-06-01

In a recent article, Joel Marks presents the amoralist argument against vivisection, or animal laboratory experimentation. He argues that ethical theories that seek to uncover some universal morality are in fact useless and unnecessary for ethical deliberations meant to determine what constitutes an appropriate action in a specific circumstance. I agree with Marks' conclusion. I too believe that vivisection is indefensible, both from a scientific and philosophical perspective. I also believe that we should become vegan (unfortunately, like the two philosophers mentioned by Marks, I too am still struggling to reduce my meat and dairy consumption). However, I am in the dark as to Marks' vision of normative deliberations in the spirit of amoralism and desirism.

Revised Mark 22 coolant temperature coefficients

International Nuclear Information System (INIS)

Graves, W.E.

1987-01-01

Coolant temperature coefficients for the Mark 22 charge published previously are non-conservative because of the neglect of a significant mechanism which has a positive contribution to reactivity. Even after correcting for this effect, dynamic tests made on a Mark VIB charge in the early 60's suggest the results are still non-conservative. This memorandum takes both of these sources of information into account in making a best estimate of the prompt (coolant plus metal) temperature coefficient. Although no safety issues arise from this work (the overall temperature coefficient still strongly contributes to reactor stability), it is obviously desirable to use best estimates for prompt coefficients in limits and other calculations

22 CFR 226.91 - Marking.

Science.gov (United States)

2010-04-01

... Relations AGENCY FOR INTERNATIONAL DEVELOPMENT ADMINISTRATION OF ASSISTANCE AWARDS TO U.S. NON-GOVERNMENTAL ORGANIZATIONS Miscellaneous § 226.91 Marking. (a) USAID policy is that all programs, projects, activities... support of the American people through the United States Agency for International Development (USAID). The...

Problems with ink skin markings for radiation field setups

International Nuclear Information System (INIS)

Endoh, Masaru; Saeki, Mituaki; Ishida, Yusei

1982-01-01

Ink skin markings are used in radiation therapy to aid in reproduction of treatment field setups or to indelibly outline field markings or tumors. We reported two cases of indelible ink skin for radiation field septa with minimal discomfort and dermatitis have been experienced for 6 months and above since end of radiotherapy. These indelible ink skin markings look like tattoo that will be big problems in the case of young female. We improved these problems by using of 10 percent silver nitrate instead of habitual skin ink. (author)

Maaväline lind Mark Raidpere / Fagira D. Morti

Index Scriptorium Estoniae

Fagira D. Morti, pseud., 1974-

2009-01-01

Soome Vabariigi president Tarja Halonen andis 28. veebruaril 2009. aastal Kumu Kunstimuuseumis videokunstnik Mark Raidperele üle Ars Fennica kunstipreemia. Meenutusi kunstniku EHI-s õppimise ajast, esimese näituse "Ilo" avamisest Vaal galeriis. Mark Raidpere loomingu mõistmisest

THE MARK I BUSINESS SYSTEM SIMULATION MODEL

Science.gov (United States)

of a large-scale business simulation model as a vehicle for doing research in management controls. The major results of the program were the...development of the Mark I business simulation model and the Simulation Package (SIMPAC). SIMPAC is a method and set of programs facilitating the construction...of large simulation models. The object of this document is to describe the Mark I Corporation model, state why parts of the business were modeled as they were, and indicate the research applications of the model. (Author)

The Things of Caesar: Mark-ing the Plural (Mk 12:13–17

Directory of Open Access Journals (Sweden)

Warren Carter

2014-09-01

Full Text Available This article observes the rarely-discussed phenomenon that the Marcan paying-the-tax scene refers to tax in the singular, whilst the concluding saying uses the plural ‘the things of Caesar and of God’. The article accounts for this phenomenon by means of developing traditions. The section under the heading ‘Mark’s scene and saying about taxes (12:13–17’ counters the common claim that scene and saying originated as a unit from the historical Jesus. It proposes that whilst the saying may have originated with Jesus, the scene as we have it did not. The section under the heading ‘Social memory, orality, and a multi-referential saying?’ suggests some contexts that the saying about the things of Caesar addressed pre-Mark. And under the section ‘Trauma and Mark’s scene’ it is argued that Mark created a unit comprising scene and saying to negotiate the ‘ trauma’ of the 66–70 war. The unit evaluates freshly-asserted Roman power as idolatrous and blasphemous whilst simultaneously authorising the continued involvement of Jesus-believers in imperial society.

Evaluation of TRIGA Mark II reactor in Turkey

International Nuclear Information System (INIS)

Bilge, Ali Nezihi

1990-01-01

There are two research reactors in Turkey and one of them is the university Triga Mark II reactor which was in service since 1979 both for education and industrial application purposes. The main aim of this paper is to evaluate the spectrum of the services carried by Turkish Triga Mark II reactor. In this work, statistical distribution of the graduate works and applications, by using Triga Mark II reactor is examined and evaluated. In addition to this, technical and scientific uses of this above mentioned reactor are also investigated. It was already showed that the uses and benefits of this reactor can not be limited. If the sufficient work and service is given, NDT and industrial applications can also be carried economically. (orig.)

New Developments in Natural Hazard Management

Science.gov (United States)

Stötter, J.; Meißl, G.; Weck-Hannemann, H.; Veulliet, E.

2003-04-01

Natural hazard processes such as avalanches, debris flows, rockfalls, slides, slow mass movements and floods inherently threaten areas used for settlements, economic activities or transport in mountain regions like the Alps. In the recent past an increasing demand for new settlement, traffic and other land use areas has arisen, resulting in intensified utilization of land known to be threatened by natural hazard processes. In the same time a decrease of individual responsibility can be observed, leading to a growing call for protection by public authorities. As public financial resources become more limited in these days and the outsourcing of areas of traditional government responsibility increases, there is an urgent need for new, more effective and efficient strategies in natural hazard management, involving all relevant actors. To meet these new demands in dealing with natural hazards, the "alpS - Centre of Natural Hazard Management" was founded in October 2002 in Innsbruck/Austria, supported by the Austrian Government. Central goal of the alpS - Centre is to elaborate the basis for future sustainable safety of the alpine lebensraum. The following objectives will be addressed by an interdisciplinary team: - Systematic compilation and evaluation of the present situation. - Developing a more efficient and effective way of natural hazard management. - Implementation of a paradigm change. - Development of strategies for natural hazard management under changed frame conditions in the future (global change). Strong emphasis is laid on research on the socio-economic aspects of Natural Hazard Management, which have been more or less neglected up to now.

The perception of hazards

International Nuclear Information System (INIS)

Fritzsche, A.F.

1986-01-01

The fourth chapter deals with the profusion of factors determining the differing assessment of hazards by our society. Subjective factors influencing risk perception comprise, among others, general knowledge and recognition of a hazard; the degree of voluntariness when taking the risk and its influencibility; the problem of large scale accidents; immediate and delayed results. Next to the objective and the subjective risks, the individual and the social or collective risks are assessed differently. The author dicusses in detail recent investigations into and study methods for the determination of risk perception, while eliminating systematic trends from subjective perception since common assessments are shared by whole groups of individuals time and again which allow a better understanding of today's handling of hazards. (HSCH) [de

Urban Heat Wave Hazard Assessment

Science.gov (United States)

Quattrochi, D. A.; Jedlovec, G.; Crane, D. L.; Meyer, P. J.; LaFontaine, F.

2016-12-01

Heat waves are one of the largest causes of environmentally-related deaths globally and are likely to become more numerous as a result of climate change. The intensification of heat waves by the urban heat island effect and elevated humidity, combined with urban demographics, are key elements leading to these disasters. Better warning of the potential hazards may help lower risks associated with heat waves. Moderate resolution thermal data from NASA satellites is used to derive high spatial resolution estimates of apparent temperature (heat index) over urban regions. These data, combined with demographic data, are used to produce a daily heat hazard/risk map for selected cities. MODIS data are used to derive daily composite maximum and minimum land surface temperature (LST) fields to represent the amplitude of the diurnal temperature cycle and identify extreme heat days. Compositing routines are used to generate representative daily maximum and minimum LSTs for the urban environment. The limited effect of relative humidity on the apparent temperature (typically 10-15%) allows for the use of modeled moisture fields to convert LST to apparent temperature without loss of spatial variability. The daily max/min apparent temperature fields are used to identify abnormally extreme heat days relative to climatological values in order to produce a heat wave hazard map. Reference to climatological values normalizes the hazard for a particular region (e.g., the impact of an extreme heat day). A heat wave hazard map has been produced for several case study periods and then computed on a quasi-operational basis during the summer of 2016 for Atlanta, GA, Chicago, IL, St. Louis, MO, and Huntsville, AL. A hazard does not become a risk until someone or something is exposed to that hazard at a level that might do harm. Demographic information is used to assess the urban risk associated with the heat wave hazard. Collectively, the heat wave hazard product can warn people in urban

An innovative road marking quality assessment mechanism using computer vision

Directory of Open Access Journals (Sweden)

Kuo-Liang Lin

2016-06-01

Full Text Available Aesthetic quality acceptance for road marking works has been relied on subjective visual examination. Due to a lack of quantitative operation procedures, acceptance outcome can be biased and results in great quality variation. To improve aesthetic quality acceptance procedure of road marking, we develop an innovative road marking quality assessment mechanism, utilizing machine vision technologies. Using edge smoothness as a quantitative aesthetic indicator, the proposed prototype system first receives digital images of finished road marking surface and has the images processed and analyzed to capture the geometric characteristics of the marking. The geometric characteristics are then evaluated to determine the quality level of the finished work. System is demonstrated through two real cases to show how it works. In the end, a test comparing the assessment results between the proposed system and expert inspection is conducted to enhance the accountability of the proposed mechanism.

76 FR 16534 - Hazardous Waste Management System Identification and Listing of Hazardous Waste; Final Exclusion

Science.gov (United States)

2011-03-24

... Waste Management System Identification and Listing of Hazardous Waste; Final Exclusion AGENCY...) on a one-time basis from the lists of hazardous waste, a certain solid waste generated at its Mt... waste is [[Page 16535

75 FR 57686 - Hazardous Waste Management System; Identification and Listing of Hazardous Waste Amendment

Science.gov (United States)

2010-09-22

... Waste Management System; Identification and Listing of Hazardous Waste Amendment AGENCY: Environmental...) 260.20 and 260.22 allows facilities to demonstrate that a specific waste from a particular generating facility should not be regulated as a hazardous waste. Based on waste-specific information provided by the...

76 FR 51324 - Hazardous Materials: Incorporating Rail Special Permits Into the Hazardous Materials Regulations

Science.gov (United States)

2011-08-18

... through use of electronic data interchange (EDI). The IVOHMA states ``differences in hazard communication... and on the possible effects EDI may have on distributing hazardous materials shipping paper... consider the use of EDI in other modes of transport in a future rulemaking. Petition No. P-1567 PHMSA...

Occupational hazards to health of port workers.

Science.gov (United States)

Wang, Yukun; Zhan, Shuifen; Liu, Yan; Li, Yan

2017-12-01

The aim of this article is to reduce the risk of occupational hazards and improve safety conditions by enhancing hazard knowledge and identification as well as improving safety behavior for freight port enterprises. In the article, occupational hazards to health and their prevention measures of freight port enterprises have been summarized through a lot of occupational health evaluation work, experience and understanding. Workers of freight port enterprises confront an equally wide variety of chemical, physical and psychological hazards in production technology, production environment and the course of labor. Such health hazards have been identified, the risks evaluated, the dangers to health notified and effective prevention measures which should be put in place to ensure the health of the port workers summarized. There is still a long way to go for the freight port enterprises to prevent and control the occupational hazards. Except for occupational hazards and their prevention measures, other factors that influence the health of port workers should also be paid attention to, such as age, work history, gender, contraindication and even the occurrence and development rules of occupational hazards in current production conditions.

Use of rhodamine B to mark the body and seminal fluid of male Aedes aegypti for mark-release-recapture experiments and estimating efficacy of sterile male releases.

Science.gov (United States)

Johnson, Brian J; Mitchell, Sara N; Paton, Christopher J; Stevenson, Jessica; Staunton, Kyran M; Snoad, Nigel; Beebe, Nigel; White, Bradley J; Ritchie, Scott A

2017-09-01

Recent interest in male-based sterile insect technique (SIT) and incompatible insect technique (IIT) to control Aedes aegypti and Aedes albopictus populations has revealed the need for an economical, rapid diagnostic tool for determining dispersion and mating success of sterilized males in the wild. Previous reports from other insects indicated rhodamine B, a thiol-reactive fluorescent dye, administered via sugar-feeding can be used to stain the body tissue and seminal fluid of insects. Here, we report on the adaptation of this technique for male Ae. aegypti to allow for rapid assessment of competitiveness (mating success) during field releases. Marking was achieved by feeding males on 0.1, 0.2, 0.4 or 0.8% rhodamine B (w/v) in 50% honey solutions during free flight. All concentrations produced >95% transfer to females and successful body marking after 4 days of feeding, with 0.4 and 0.8% solutions producing the longest-lasting body marking. Importantly, rhodamine B marking had no effect on male mating competitiveness and proof-of-principle field releases demonstrated successful transfer of marked seminal fluid to females under field conditions and recapture of marked males. These results reveal rhodamine B to be a potentially useful evaluation method for male-based SIT/IIT control strategies as well as a viable body marking technique for male-based mark-release-recapture experiments without the negative side-effects of traditional marking methods. As a standalone method for use in mating competitiveness assays, rhodamine B marking is less expensive than PCR (e.g. paternity analysis) and stable isotope semen labelling methods and less time-consuming than female fertility assays used to assess competitiveness of sterilised males.

Use of rhodamine B to mark the body and seminal fluid of male Aedes aegypti for mark-release-recapture experiments and estimating efficacy of sterile male releases.

Directory of Open Access Journals (Sweden)

Brian J Johnson

2017-09-01

Full Text Available Recent interest in male-based sterile insect technique (SIT and incompatible insect technique (IIT to control Aedes aegypti and Aedes albopictus populations has revealed the need for an economical, rapid diagnostic tool for determining dispersion and mating success of sterilized males in the wild. Previous reports from other insects indicated rhodamine B, a thiol-reactive fluorescent dye, administered via sugar-feeding can be used to stain the body tissue and seminal fluid of insects. Here, we report on the adaptation of this technique for male Ae. aegypti to allow for rapid assessment of competitiveness (mating success during field releases.Marking was achieved by feeding males on 0.1, 0.2, 0.4 or 0.8% rhodamine B (w/v in 50% honey solutions during free flight. All concentrations produced >95% transfer to females and successful body marking after 4 days of feeding, with 0.4 and 0.8% solutions producing the longest-lasting body marking. Importantly, rhodamine B marking had no effect on male mating competitiveness and proof-of-principle field releases demonstrated successful transfer of marked seminal fluid to females under field conditions and recapture of marked males.These results reveal rhodamine B to be a potentially useful evaluation method for male-based SIT/IIT control strategies as well as a viable body marking technique for male-based mark-release-recapture experiments without the negative side-effects of traditional marking methods. As a standalone method for use in mating competitiveness assays, rhodamine B marking is less expensive than PCR (e.g. paternity analysis and stable isotope semen labelling methods and less time-consuming than female fertility assays used to assess competitiveness of sterilised males.

Prosodic Focus Marking in Bai.

NARCIS (Netherlands)

Liu, Zenghui; Chen, A.; Van de Velde, Hans

2014-01-01

This study investigates prosodic marking of focus in Bai, a Sino-Tibetan language spoken in the Southwest of China, by adopting a semi-spontaneous experimental approach. Our data show that Bai speakers increase the duration of the focused constituent and reduce the duration of the post-focus

Hazardous industrial waste management

International Nuclear Information System (INIS)

Quesada, Hilda; Salas, Juan Carlos; Romero, Luis Guillermo

2007-01-01

The appropriate managing of hazardous wastes is a problem little dealed in the wastes management in the country. A search of available information was made about the generation and handling to internal and external level of the hazardous wastes by national industries. It was worked with eleven companies of different types of industrial activities for, by means of a questionnaire, interviews and visits, to determine the degree of integral and suitable handling of the wastes that they generate. It was concluded that exist only some isolated reports on the generation of hazardous industrial wastes and handling. The total quantity of wastes generated in the country was impossible to establish. The companies consulted were deficient in all stages of the handling of their wastes: generation, accumulation and storage, transport, treatment and final disposition. The lack of knowledge of the legislation and of the appropriate managing of the wastes is showed as the principal cause of the poor management of the residues. The lack of state or private entities entrusted to give services of storage, transport, treatment and final disposition of hazardous wastes in the country was evident. (author) [es

Full-Scale Mark II CRT Program data report, 1

International Nuclear Information System (INIS)

Namatame, Ken; Kukita, Yutaka; Yamamoto, Nobuo; Shiba, Masayoshi

1979-12-01

The Full-Scale Mark II CRT (Containment Response Test) Program was initiated in April 1976 to provide a full-scale data basis for the evaluation of the pressure suppression pool hydrodynamic loads associated with a hypothetical LOCA in a BWR Mark II Containment. The test facility, completed in March 1979, is 1/18 in volume of a typical 1100 MWe Mark II, and has a wetwell which is a full-scale replica of one 20 0 -sector of that of the reference Mark II. The present report documents experimental data from TEST 0002, a medium size (100 mm) water blowdown test, performed by Hitachi Ltd. for JAERI as the second of the four shakedown tests. Test data is provided for the vessel depressurization, the pressure and temperature responses in the test containment, and especially for the chugging phenomena associated with low flux steam condensation in the pool. (author)

49 CFR 180.213 - Requalification markings.

Science.gov (United States)

2010-10-01

... eddy current examination combined with a visual inspection, the marking is as illustrated in paragraph..., securely affixed in a manner prescribed by the cylinder manufacturer, near the original manufacturer's...

Plutonium Finishing Plant (PFP) hazards assessment

International Nuclear Information System (INIS)

Campbell, L.R.

1998-01-01

This report documents the hazards assessment for the Plutonium Finishing Plant (PFP) located on the US Department of Energy (DOE) Hanford Site. This hazards assessment was conducted to provide the emergency planning technical basis for the PFP. DOE Orders require an emergency planning hazards assessment for each facility that has the potential to reach or exceed the lowest level emergency classification

K Basin Hazard Analysis

Energy Technology Data Exchange (ETDEWEB)

PECH, S.H.

2000-08-23

This report describes the methodology used in conducting the K Basins Hazard Analysis, which provides the foundation for the K Basins Final Safety Analysis Report. This hazard analysis was performed in accordance with guidance provided by DOE-STD-3009-94, Preparation Guide for U. S. Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports and implements the requirements of DOE Order 5480.23, Nuclear Safety Analysis Report.

K Basin Hazard Analysis

International Nuclear Information System (INIS)

PECH, S.H.

2000-01-01

This report describes the methodology used in conducting the K Basins Hazard Analysis, which provides the foundation for the K Basins Final Safety Analysis Report. This hazard analysis was performed in accordance with guidance provided by DOE-STD-3009-94, Preparation Guide for U. S. Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports and implements the requirements of DOE Order 5480.23, Nuclear Safety Analysis Report

Laser marking as a result of applying reverse engineering

Science.gov (United States)

Mihalache, Andrei; Nagîţ, Gheorghe; Rîpanu, Marius Ionuţ; Slǎtineanu, Laurenţiu; Dodun, Oana; Coteaţǎ, Margareta

2018-05-01

The elaboration of a modern manufacturing technology needs a certain quantum of information concerning the part to be obtained. When it is necessary to elaborate the technology for an existing object, such an information could be ensured by using the principles specific to the reverse engineering. Essentially, in the case of this method, the analysis of the surfaces and of other characteristics of the part must offer enough information for the elaboration of the part manufacturing technology. On the other hand, it is known that the laser marking is a processing method able to ensure the transfer of various inscriptions or drawings on a part. Sometimes, the laser marking could be based on the analysis of an existing object, whose image could be used to generate the same object or an improved object. There are many groups of factors able to affect the results of applying the laser marking process. A theoretical analysis was proposed to show that the heights of triangles obtained by means of a CNC marking equipment depend on the width of the line generated by the laser spot on the workpiece surface. An experimental research was thought and materialized to highlight the influence exerted by the line with and the angle of lines intersections on the accuracy of the marking process. By mathematical processing of the experimental results, empirical mathematical models were determined. The power type model and the graphical representation elaborated on the base of this model offered an image concerning the influences exerted by the considered input factors on the marking process accuracy.

Hazards assessment for the Waste Experimental Reduction Facility

International Nuclear Information System (INIS)

Calley, M.B.; Jones, J.L. Jr.

1994-01-01

This report documents the hazards assessment for the Waste Experimental Reduction Facility (WERF) located at the Idaho National Engineering Laboratory, which is operated by EG ampersand G Idaho, Inc., for the US Department of Energy (DOE). The hazards assessment was performed to ensure that this facility complies with DOE and company requirements pertaining to emergency planning and preparedness for operational emergencies. DOE Order 5500.3A requires that a facility-specific hazards assessment be performed to provide the technical basis for facility emergency planning efforts. This hazards assessment was conducted in accordance with DOE Headquarters and DOE Idaho Operations Office (DOE-ID) guidance to comply with DOE Order 5500.3A. The hazards assessment identifies and analyzes hazards that are significant enough to warrant consideration in a facility's operational emergency management program. This hazards assessment describes the WERF, the area surrounding WERF, associated buildings and structures at WERF, and the processes performed at WERF. All radiological and nonradiological hazardous materials stored, used, or produced at WERF were identified and screened. Even though the screening process indicated that the hazardous materials could be screened from further analysis because the inventory of radiological and nonradiological hazardous materials were below the screening thresholds specified by DOE and DOE-ID guidance for DOE Order 5500.3A, the nonradiological hazardous materials were analyzed further because it was felt that the nonradiological hazardous material screening thresholds were too high

Hazards assessment for the Waste Experimental Reduction Facility

Energy Technology Data Exchange (ETDEWEB)

Calley, M.B.; Jones, J.L. Jr.

1994-09-19

This report documents the hazards assessment for the Waste Experimental Reduction Facility (WERF) located at the Idaho National Engineering Laboratory, which is operated by EG&G Idaho, Inc., for the US Department of Energy (DOE). The hazards assessment was performed to ensure that this facility complies with DOE and company requirements pertaining to emergency planning and preparedness for operational emergencies. DOE Order 5500.3A requires that a facility-specific hazards assessment be performed to provide the technical basis for facility emergency planning efforts. This hazards assessment was conducted in accordance with DOE Headquarters and DOE Idaho Operations Office (DOE-ID) guidance to comply with DOE Order 5500.3A. The hazards assessment identifies and analyzes hazards that are significant enough to warrant consideration in a facility`s operational emergency management program. This hazards assessment describes the WERF, the area surrounding WERF, associated buildings and structures at WERF, and the processes performed at WERF. All radiological and nonradiological hazardous materials stored, used, or produced at WERF were identified and screened. Even though the screening process indicated that the hazardous materials could be screened from further analysis because the inventory of radiological and nonradiological hazardous materials were below the screening thresholds specified by DOE and DOE-ID guidance for DOE Order 5500.3A, the nonradiological hazardous materials were analyzed further because it was felt that the nonradiological hazardous material screening thresholds were too high.

Parts Quality Management: Direct Part Marking via Data Matrix Symbols for Mission Assurance

Science.gov (United States)

Moss, Chantrice

2013-01-01

A United States Government Accountability Office (GAO) review of twelve NASA programs found widespread parts quality problems contributing to significant cost overruns, schedule delays, and reduced system reliability. Direct part-marking with Data Matrix symbols could significantly improve the quality of inventory control and parts lifecycle management. This paper examines the feasibility of using 15 marking technologies for use in future NASA programs. A structural analysis is based on marked material type, operational environment (e.g., ground, suborbital, orbital), durability of marks, ease of operation, reliability, and affordability. A cost-benefits analysis considers marking technology (data plates, label printing, direct part marking) and marking types (two-dimensional machine-readable, human-readable). Previous NASA parts marking efforts and historical cost data are accounted for, including in-house vs. outsourced marking. Some marking methods are still under development. While this paper focuses on NASA programs, results may be applicable to a variety of industrial environments.

Parts Quality Management: Direct Part Marking of Data Matrix Symbol for Mission Assurance

Science.gov (United States)

Moss, Chantrice; Chakrabarti, Suman; Scott, David W.

2013-01-01

A United States Government Accountability Office (GAO) review of twelve NASA programs found widespread parts quality problems contributing to significant cost overruns, schedule delays, and reduced system reliability. Direct part marking with Data Matrix symbols could significantly improve the quality of inventory control and parts lifecycle management. This paper examines the feasibility of using direct part marking technologies for use in future NASA programs. A structural analysis is based on marked material type, operational environment (e.g., ground, suborbital, Low Earth Orbit), durability of marks, ease of operation, reliability, and affordability. A cost-benefits analysis considers marking technology (label printing, data plates, and direct part marking) and marking types (two-dimensional machine-readable, human-readable). Previous NASA parts marking efforts and historical cost data are accounted for, including inhouse vs. outsourced marking. Some marking methods are still under development. While this paper focuses on NASA programs, results may be applicable to a variety of industrial environments.

Hazardous materials and toxic substances - Status report

International Nuclear Information System (INIS)

Sommerlad, R.E.

1991-01-01

The paper first forecasts what the status of hazardous wastes should be in the year 2028. The author believes all the problems will be solved: no new hazardous wastes will be being generated and the current hazardous waste problems will have been cleared up by common sense engineering. He then describes the current status of waste management of hazardous wastes, the regulatory situation, as well as combustion test programs

Regulation of glucose homeostasis by KSR1 and MARK2.

Directory of Open Access Journals (Sweden)

Paula J Klutho

Full Text Available Protein scaffolds control the intensity and duration of signaling and dictate the specificity of signaling through MAP kinase pathways. KSR1 is a molecular scaffold of the Raf/MEK/ERK MAP kinase cascade that regulates the intensity and duration of ERK activation. Relative to wild-type mice, ksr1⁻/⁻ mice are modestly glucose intolerant, but show a normal response to exogenous insulin. However, ksr1⁻/⁻ mice also demonstrate a three-fold increase in serum insulin levels in response to a glucose challenge, suggesting a role for KSR1 in insulin secretion. The kinase MARK2 is closely related to C-TAK1, a known regulator of KSR1. Mice lacking MARK2 have an increased rate of glucose disposal in response to exogenous insulin, increased glucose tolerance, and are resistant to diet-induced obesity. mark2⁻/⁻ksr1⁻/⁻ (DKO mice were compared to wild type, mark2⁻/⁻, and ksr1⁻/⁻ mice for their ability to regulate glucose homeostasis. Here we show that disruption of KSR1 in mark2⁻/⁻ mice reverses the increased sensitivity to exogenous insulin resulting from MARK2 deletion. DKO mice respond to exogenous insulin similarly to wild type and ksr1⁻/⁻ mice. These data suggest a model whereby MARK2 negatively regulates insulin sensitivity in peripheral tissue through inhibition of KSR1. Consistent with this model, we found that MARK2 binds and phosphorylates KSR1 on Ser392. Phosphorylation of Ser392 is a critical regulator of KSR1 stability, subcellular location, and ERK activation. These data reveal an unexpected role for the molecular scaffold KSR1 in insulin-regulated glucose metabolism.

Hazardous materials

Science.gov (United States)

... substances that could harm human health or the environment. Hazardous means dangerous, so these materials must be ... M. is also a founding member of Hi-Ethics and subscribes to the principles of the Health ...

Geological hazard monitoring system in Georgia

Science.gov (United States)

Gaprindashvili, George

2017-04-01

Georgia belongs to one of world's most complex mountainous regions according to the scale and frequency of Geological processes and damage caused to population, farmlands, and Infrastructure facilities. Geological hazards (landslide, debrisflow/mudflow, rockfall, erosion and etc.) are affecting many populated areas, agricultural fields, roads, oil and gas pipes, high-voltage electric power transmission towers, hydraulic structures, and tourist complexes. Landslides occur almost in all geomorphological zones, resulting in wide differentiation in the failure types and mechanisms and in the size-frequency distribution. In Georgia, geological hazards triggered by: 1. Activation of highly intense earthquakes; 2. Meteorological events provoking the disaster processes on the background of global climatic change; 3. Large-scale Human impact on the environment. The prediction and monitoring of Geological Hazards is a very wide theme, which involves different researchers from different spheres. Geological hazard monitoring is essential to prevent and mitigate these hazards. In past years in Georgia several monitoring system, such as Ground-based geodetic techniques, Debrisflow Early Warning System (EWS) were installed on high sensitive landslide and debrisflow areas. This work presents description of Geological hazard monitoring system in Georgia.

Hazardous drugs: new challenges, new opportunities

Directory of Open Access Journals (Sweden)

Silvia Valero García

2016-03-01

Full Text Available Occupational exposure to hazardous drugs can cause harmful effects on health professionals and several protective measures must be taken. Nevertheless, classification of hazardous drugs is not the same in all the published repertoires and the terminology is still confusing: hazardous drugs, biohazardous drugs or risky drugs are terms improperly described and can define very different drugs with a very different hazard profiles. In Spain, there is not an updated official list of hazardous drugs, and healthcare professionals must consider and follow other published lists. In our opinion, it is mandatory to do a consensus among these professionals, administration and labor union organizations in order to clarify some conflictive questions not only in healthcare settings but in investigational and academic scenarios too. These multidisciplinary groups should be involved also in teaching new and non-experienced personnel and in the knowledge reinforcement for the experienced ones

Technologies to remediate hazardous waste sites

International Nuclear Information System (INIS)

Falco, J.W.

1990-03-01

Technologies to remediate hazardous wastes must be matched with the properties of the hazardous materials to be treated, the environment in which the wastes are imbedded, and the desired extent of remediation. Many promising technologies are being developed, including biological treatment, immobilization techniques, and in situ methods. Many of these new technologies are being applied to remediate sites. The management and disposal of hazardous wastes is changing because of federal and state legislation as well as public concern. Future waste management systems will emphasize the substitution of alternatives for the use of hazardous materials and process waste recycling. Onsite treatment will also become more frequently adopted. 5 refs., 7 figs

FIRE HAZARDS ANALYSIS - BUSTED BUTTE

International Nuclear Information System (INIS)

Longwell, R.; Keifer, J.; Goodin, S.

2001-01-01

The purpose of this fire hazards analysis (FHA) is to assess the risk from fire within individual fire areas at the Busted Butte Test Facility and to ascertain whether the DOE fire safety objectives are met. The objective, identified in DOE Order 420.1, Section 4.2, is to establish requirements for a comprehensive fire and related hazards protection program for facilities sufficient to minimize the potential for: (1) The occurrence of a fire related event. (2) A fire that causes an unacceptable on-site or off-site release of hazardous or radiological material that will threaten the health and safety of employees. (3) Vital DOE programs suffering unacceptable interruptions as a result of fire and related hazards. (4) Property losses from a fire and related events exceeding limits established by DOE. Critical process controls and safety class systems being damaged as a result of a fire and related events

Relative Hazard and Risk Measure Calculation Methodology

International Nuclear Information System (INIS)

Stenner, Robert D.; Strenge, Dennis L.; Elder, Matthew S.; Andrews, William B.; Walton, Terry L.

2003-01-01

The RHRM equations, as represented in methodology and code presented in this report, are primarily a collection of key factors normally used in risk assessment that are relevant to understanding the hazards and risks associated with projected mitigation, cleanup, and risk management activities. The RHRM code has broad application potential. For example, it can be used to compare one mitigation, cleanup, or risk management activity with another, instead of just comparing it to just the fixed baseline. If the appropriate source term data are available, it can be used in its non-ratio form to estimate absolute values of the associated controlling hazards and risks. These estimated values of controlling hazards and risks can then be examined to help understand which mitigation, cleanup, or risk management activities are addressing the higher hazard conditions and risk reduction potential at a site. Graphics can be generated from these absolute controlling hazard and risk values to graphically compare these high hazard and risk reduction potential conditions. If the RHRM code is used in this manner, care must be taken to specifically define and qualify (e.g., identify which factors were considered and which ones tended to drive the hazard and risk estimates) the resultant absolute controlling hazard and risk values

Storage of hazardous substances in bonded warehouses

International Nuclear Information System (INIS)

Villalobos Artavia, Beatriz

2008-01-01

A variety of special regulations exist in Costa Rica for registration and transport of hazardous substances; these set the requirements for entry into the country and the security of transport units. However, the regulations mentioned no specific rules for storing hazardous substances. Tax deposits have been the initial place where are stored the substances that enter the country.The creation of basic rules that would be regulating the storage of hazardous substances has taken place through the analysis of regulations and national and international laws governing hazardous substances. The regulatory domain that currently exists will be established with a field research in fiscal deposits in the metropolitan area. The storage and security measures that have been used by the personnel handling the substances will be identified to be putting the reality with that the hazardous substances have been handled in tax deposits. A rule base for the storage of hazardous substances in tax deposits can be made, protecting the safety of the environment in which are manipulated and avoiding a possible accident causing a mess around. The rule will have the characteristics of the storage warehouses hazardous substances, such as safety standards, labeling standards, infrastructure features, common storage and transitional measures that must possess and meet all bonded warehouses to store hazardous substances. (author) [es

Microstructure of gross chill-mark defect in a glass-ceramic preform

International Nuclear Information System (INIS)

Spears, R.K.

1980-01-01

The microstructure of a vacuum tube glass-ceramic preform containing gross chill-marks on the top and bottom surfaces as well as on the sides was analyzed. The preform was ceramed in a graphite mold and examined using SEM. The glass-ceramic had an extremely dense and fine crystalline structure except where the chill-marks were located. In those areas of matrix glass following the chill-mark plane were evident. It is concluded that gross chill-marks will affect the microstructure by disrupting the chemistry or nucleating characteristics in such a way that a chill-mark regon would appear to be depleted of crystallites. Although the crystallites in this region are larger, the quantity is lower than in the base glass-ceramic. The affected area caused by the chill-mark left a band of matrix glass approximately 100 μ wide. It is believed that planar defects of this size will degrade the mechanical and permeation properties of the glass-ceramic

9 CFR 592.340 - Supervision of marking and packaging.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Supervision of marking and packaging... § 592.340 Supervision of marking and packaging. (a) Evidence of label approval. Inspection program... evidence that such official identification or packaging material bearing such official identification has...

76 FR 11432 - Coding of Design Marks in Registrations

Science.gov (United States)

2011-03-02

...] Coding of Design Marks in Registrations AGENCY: United States Patent and Trademark Office, Commerce... practice of coding newly registered trademarks that include a design element with design mark codes based... notice and request for comments at 75 FR 81587, proposing to discontinue a secondary system of coding...

Hazardous waste sites and housing appreciation rates

OpenAIRE

McCluskey, Jill Jennifer; Rausser, Gordon C

2000-01-01

The dynamic effect of a hazardous waste site is analyzed by investigating the causal relationship between housing appreciation rates and house location in relation to a hazardous waste site using resale data from individual sales transactions in Dallas County, Texas. The results indicate that in the period in which the hazardous waste site was identified and cleanup occurred, residential property owners in close proximity to the hazardous waste site experienced lower housing appreciation rate...

Hazard Communication Standard

International Nuclear Information System (INIS)

Sichak, S.

1991-01-01

The current rate of technological advances has brought with it an overwhelming increase in the usage of chemicals in the workplace and in the home. Coupled to this increase has been a heightened awareness in the potential for acute and chronic injuries attributable to chemical insults. The Hazard Communication Standard has been introduced with the desired goal of reducing workplace exposures to hazardous substances and thereby achieving a corresponding reduction in adverse health effects. It was created and proclaimed by the US Department of Labor and regulated by the Occupational Safety and Health Administration. 1 tab

Tsunami hazard map in eastern Bali

International Nuclear Information System (INIS)

Afif, Haunan; Cipta, Athanasius

2015-01-01

Bali is a popular tourist destination both for Indonesian and foreign visitors. However, Bali is located close to the collision zone between the Indo-Australian Plate and Eurasian Plate in the south and back-arc thrust off the northern coast of Bali resulted Bali prone to earthquake and tsunami. Tsunami hazard map is needed for better understanding of hazard level in a particular area and tsunami modeling is one of the most reliable techniques to produce hazard map. Tsunami modeling conducted using TUNAMI N2 and set for two tsunami sources scenarios which are subduction zone in the south of Bali and back thrust in the north of Bali. Tsunami hazard zone is divided into 3 zones, the first is a high hazard zones with inundation height of more than 3m. The second is a moderate hazard zone with inundation height 1 to 3m and the third is a low tsunami hazard zones with tsunami inundation heights less than 1m. Those 2 scenarios showed southern region has a greater potential of tsunami impact than the northern areas. This is obviously shown in the distribution of the inundated area in the south of Bali including the island of Nusa Penida, Nusa Lembongan and Nusa Ceningan is wider than in the northern coast of Bali although the northern region of the Nusa Penida Island more inundated due to the coastal topography

Tsunami hazard map in eastern Bali

Energy Technology Data Exchange (ETDEWEB)

Afif, Haunan, E-mail: afif@vsi.esdm.go.id [Geological Agency, Bandung (Indonesia); Cipta, Athanasius [Geological Agency, Bandung (Indonesia); Australian National University, Canberra (Australia)

2015-04-24

Bali is a popular tourist destination both for Indonesian and foreign visitors. However, Bali is located close to the collision zone between the Indo-Australian Plate and Eurasian Plate in the south and back-arc thrust off the northern coast of Bali resulted Bali prone to earthquake and tsunami. Tsunami hazard map is needed for better understanding of hazard level in a particular area and tsunami modeling is one of the most reliable techniques to produce hazard map. Tsunami modeling conducted using TUNAMI N2 and set for two tsunami sources scenarios which are subduction zone in the south of Bali and back thrust in the north of Bali. Tsunami hazard zone is divided into 3 zones, the first is a high hazard zones with inundation height of more than 3m. The second is a moderate hazard zone with inundation height 1 to 3m and the third is a low tsunami hazard zones with tsunami inundation heights less than 1m. Those 2 scenarios showed southern region has a greater potential of tsunami impact than the northern areas. This is obviously shown in the distribution of the inundated area in the south of Bali including the island of Nusa Penida, Nusa Lembongan and Nusa Ceningan is wider than in the northern coast of Bali although the northern region of the Nusa Penida Island more inundated due to the coastal topography.

Tsunami hazard map in eastern Bali

Science.gov (United States)

Afif, Haunan; Cipta, Athanasius

2015-04-01

Bali is a popular tourist destination both for Indonesian and foreign visitors. However, Bali is located close to the collision zone between the Indo-Australian Plate and Eurasian Plate in the south and back-arc thrust off the northern coast of Bali resulted Bali prone to earthquake and tsunami. Tsunami hazard map is needed for better understanding of hazard level in a particular area and tsunami modeling is one of the most reliable techniques to produce hazard map. Tsunami modeling conducted using TUNAMI N2 and set for two tsunami sources scenarios which are subduction zone in the south of Bali and back thrust in the north of Bali. Tsunami hazard zone is divided into 3 zones, the first is a high hazard zones with inundation height of more than 3m. The second is a moderate hazard zone with inundation height 1 to 3m and the third is a low tsunami hazard zones with tsunami inundation heights less than 1m. Those 2 scenarios showed southern region has a greater potential of tsunami impact than the northern areas. This is obviously shown in the distribution of the inundated area in the south of Bali including the island of Nusa Penida, Nusa Lembongan and Nusa Ceningan is wider than in the northern coast of Bali although the northern region of the Nusa Penida Island more inundated due to the coastal topography.

Hazardous constituent source term. Revision 2

International Nuclear Information System (INIS)

1994-01-01

The Department of Energy (DOE) has several facilities that either generate and/or store transuranic (TRU)-waste from weapons program research and production. Much of this waste also contains hazardous waste constituents as regulated under Subtitle C of the Resource Conservation and Recovery Act (RCRA). Toxicity characteristic metals in the waste principally include lead, occurring in leaded rubber gloves and shielding. Other RCRA metals may occur as contaminants in pyrochemical salt, soil, debris, and sludge and solidified liquids, as well as in equipment resulting from decontamination and decommissioning activities. Volatile organic compounds (VOCS) contaminate many waste forms as a residue adsorbed on surfaces or occur in sludge and solidified liquids. Due to the presence of these hazardous constituents, applicable disposal regulations include land disposal restrictions established by Hazardous and Solid Waste Amendments (HSWA). The DOE plans to dispose of TRU-mixed waste from the weapons program in the Waste Isolation Pilot Plant (WIPP) by demonstrating no-migration of hazardous constituents. This paper documents the current technical basis for methodologies proposed to develop a post-closure RCRA hazardous constituent source term. For the purposes of demonstrating no-migration, the hazardous constituent source term is defined as the quantities of hazardous constituents that are available for transport after repository closure. Development of the source term is only one of several activities that will be involved in the no-migration demonstration. The demonstration will also include uncertainty and sensitivity analyses of contaminant transport

Nitrous Oxide Explosive Hazards

Science.gov (United States)

2008-05-01

concentrations of N2O. A test program is suggested that could answer questions about decomposition propagation control in large N2O systems and hazards...accident. OSHA fined Scaled Composites for not training their workers informing them about N2O hazards, instructing them on safe procedures, and...seemed present that could produce temperatures in excess of the autogeneous ignition temperature (AIT) for the polymers? Autogeneous ignition

The efficacy of mass-marking channel catfish fingerlings by immersion in oxytetracycline

Science.gov (United States)

Stewart, David R.

2011-01-01

Oxytetracycline (OTC) has been extensively used for marking a variety of fish species, but has never been successfully used to mark channel catfish Ictalurus punctatus. Channel catfish fingerlings (~ 25 mm TL) obtained from the Oklahoma Department of Wildlife Conservation at Byron Fish Hatchery were kept in Living Streams (791 to 1,018 L) equipped with recirculation units. Marking trials consisted of immersing channel catfish in one of three concentrations (250, 450, and 700 mg/L) OTC hydrochloride [HCl] for 6 hours. Samples of channel catfish were obtained from each group at 1-week and 4-week postimmersion. Lapilli otoliths and pectoral spines were removed to assess mark presence with an epi-fluorescent compound microscope. After one week, no marks were detected on pectoral spines for all treatments, mark detection on otoliths depended on concentration, but never exceeded 43% (700 mg/L). After four weeks, all otoliths and pectoral spines were determined marked for 700 mg/L OTC, 20% for fish immersed in 450 mg/L OTC, and 0% were marked after four weeks at the 250 mg/L OTC. Results show, channel catfish fingerlings can be successfully marked with immersion in OTC at 700 mg/L for at least 6 hours.

75 FR 71559 - Hazardous Waste Management System; Identification and Listing of Hazardous Waste; Withdrawal of...

Science.gov (United States)

2010-11-24

... ENVIRONMENTAL PROTECTION AGENCY 40 CFR Part 261 [EPA-R06-RCRA-2010-0066; SW FRL-9231-4] Hazardous Waste Management System; Identification and Listing of Hazardous Waste; Withdrawal of Direct Final Exclusion AGENCY: Environmental Protection Agency (EPA). ACTION: Withdrawal of direct final exclusion...

A methodology for physically based rockfall hazard assessment

Directory of Open Access Journals (Sweden)

G. B. Crosta

2003-01-01

Full Text Available Rockfall hazard assessment is not simple to achieve in practice and sound, physically based assessment methodologies are still missing. The mobility of rockfalls implies a more difficult hazard definition with respect to other slope instabilities with minimal runout. Rockfall hazard assessment involves complex definitions for "occurrence probability" and "intensity". This paper is an attempt to evaluate rockfall hazard using the results of 3-D numerical modelling on a topography described by a DEM. Maps portraying the maximum frequency of passages, velocity and height of blocks at each model cell, are easily combined in a GIS in order to produce physically based rockfall hazard maps. Different methods are suggested and discussed for rockfall hazard mapping at a regional and local scale both along linear features or within exposed areas. An objective approach based on three-dimensional matrixes providing both a positional "Rockfall Hazard Index" and a "Rockfall Hazard Vector" is presented. The opportunity of combining different parameters in the 3-D matrixes has been evaluated to better express the relative increase in hazard. Furthermore, the sensitivity of the hazard index with respect to the included variables and their combinations is preliminarily discussed in order to constrain as objective as possible assessment criteria.

Transportation of hazardous and nuclear materials

International Nuclear Information System (INIS)

Boryczka, M.; Shaver, D.

1989-01-01

Transportation of hazardous and radioactive materials is a vital part of the nation's economy. In recent years public concern over the relative safety of transporting hazardous materials has risen sharply. The United States has a long history of transporting hazardous and radioactive material; rocket propellants, commercial spent fuel, low-level and high-level radioactive waste has been shipped for years. While the track record for shipping these materials is excellent, the knowledge that hazardous materials are passing through communities raises the ire of citizens and local governments. Public outcry over shipments containing hazardous cargo has been especially prominent when shippers have attempted to transport rocket propellants or spent nuclear fuel. Studies of recent shipments have provided insight into the difficulties of shipping in a politically charged environment, the major issues of concern to citizens, and some of the more successful methods of dealing with public concerns. This paper focuses on lessons learned from these studies which include interviews with shippers, carriers, and regulators

Seismic hazard in the Intermountain West

Science.gov (United States)

Haller, Kathleen; Moschetti, Morgan P.; Mueller, Charles; Rezaeian, Sanaz; Petersen, Mark D.; Zeng, Yuehua

2015-01-01

The 2014 national seismic-hazard model for the conterminous United States incorporates new scientific results and important model adjustments. The current model includes updates to the historical catalog, which is spatially smoothed using both fixed-length and adaptive-length smoothing kernels. Fault-source characterization improved by adding faults, revising rates of activity, and incorporating new results from combined inversions of geologic and geodetic data. The update also includes a new suite of published ground motion models. Changes in probabilistic ground motion are generally less than 10% in most of the Intermountain West compared to the prior assessment, and ground-motion hazard in four Intermountain West cities illustrates the range and magnitude of change in the region. Seismic hazard at reference sites in Boise and Reno increased as much as 10%, whereas hazard in Salt Lake City decreased 5–6%. The largest change was in Las Vegas, where hazard increased 32–35%.

75 FR 61356 - Hazardous Waste Management System; Identification and Listing of Hazardous Waste; Correction

Science.gov (United States)

2010-10-05

... Waste Management System; Identification and Listing of Hazardous Waste; Correction AGENCY: Environmental... thermal desorber residual solids with Hazardous Waste Numbers: F037, F038, K048, K049, K050, and K051. In... and correcting it in Table 1 of appendix IX to part 261--Waste Excluded Under Sec. Sec. 260.20 and 260...

Waste minimization via destruction of hazardous organics

International Nuclear Information System (INIS)

Austin, L.R.

1991-01-01

Los Alamos National Laboratory is developing technologies that are capable of destroying hazardous organics, that is, converting them basically to water and carbon dioxide. If these technologies were incorporated into the main processing operation where the waste is produced, then the volume and toxicity of the hazardous or mix hazardous waste generated would be significantly reduced. This presentation will briefly discuss some of the waste treatment technologies under development at Los Alamos National Laboratory focused on destroying hazardous organics

Global Polynomial Kernel Hazard Estimation

DEFF Research Database (Denmark)

Hiabu, Munir; Miranda, Maria Dolores Martínez; Nielsen, Jens Perch

2015-01-01

This paper introduces a new bias reducing method for kernel hazard estimation. The method is called global polynomial adjustment (GPA). It is a global correction which is applicable to any kernel hazard estimator. The estimator works well from a theoretical point of view as it asymptotically redu...

NOAA Weather Radio - All Hazards

Science.gov (United States)

Non-Zero All Hazards Logo Emergency Alert Description Event Codes Fact Sheet FAQ Organization Search -event information for all types of hazards: weather (e.g., tornadoes, floods), natural (e.g Management or Preparedness, civil defense, police or mayor/commissioner sets up linkages to send messages on

40 CFR 270.62 - Hazardous waste incinerator permits.

Science.gov (United States)

2010-07-01

... WASTES (CONTINUED) EPA ADMINISTERED PERMIT PROGRAMS: THE HAZARDOUS WASTE PERMIT PROGRAM Special Forms of Permits § 270.62 Hazardous waste incinerator permits. When an owner or operator of a hazardous waste... 40 Protection of Environment 26 2010-07-01 2010-07-01 false Hazardous waste incinerator permits...

Tank farms hazards assessment

International Nuclear Information System (INIS)

Broz, R.E.

1994-01-01

Hanford contractors are writing new facility specific emergency procedures in response to new and revised US Department of Energy (DOE) Orders on emergency preparedness. Emergency procedures are required for each Hanford facility that has the potential to exceed the criteria for the lowest level emergency, an Alert. The set includes: (1) a facility specific procedure on Recognition and Classification of Emergencies, (2) area procedures on Initial Emergency Response and, (3) an area procedure on Protective Action Guidance. The first steps in developing these procedures are to identify the hazards at each facility, identify the conditions that could release the hazardous material, and calculate the consequences of the releases. These steps are called a Hazards Assessment. The final product is a document that is similar in some respects to a Safety Analysis Report (SAR). The document could br produced in a month for a simple facility but could take much longer for a complex facility. Hanford has both types of facilities. A strategy has been adopted to permit completion of the first version of the new emergency procedures before all the facility hazards Assessments are complete. The procedures will initially be based on input from a task group for each facility. This strategy will but improved emergency procedures in place sooner and therefore enhance Hanford emergency preparedness. The purpose of this document is to summarize the applicable information contained within the Waste Tank Facility ''Interim Safety Basis Document, WHC-SD-WM-ISB-001'' as a resource, since the SARs covering Waste Tank Operations are not current in all cases. This hazards assessment serves to collect, organize, document and present the information utilized during the determination process

Hydrotreater/Distillation Column Hazard Analysis Report Rev. 2

Energy Technology Data Exchange (ETDEWEB)

Lowry, Peter P. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wagner, Katie A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2016-04-15

This project Hazard and Risk Analysis Report contains the results of several hazard analyses and risk assessments. An initial assessment was conducted in 2012, which included a multi-step approach ranging from design reviews to a formal What-If hazard analysis. A second What-If hazard analysis was completed during February 2013 to evaluate the operation of the hydrotreater/distillation column processes to be installed in a process enclosure within the Process Development Laboratory West (PDL-West) facility located on the PNNL campus. The qualitative analysis included participation of project and operations personnel and applicable subject matter experts. The analysis identified potential hazardous scenarios, each based on an initiating event coupled with a postulated upset condition. The unmitigated consequences of each hazardous scenario were generally characterized as a process upset; the exposure of personnel to steam, vapors or hazardous material; a spray or spill of hazardous material; the creation of a flammable atmosphere; or an energetic release from a pressure boundary.

Continuous assessment and matriculation examination marks – An empirical examination

Directory of Open Access Journals (Sweden)

Servaas van der Berg

2015-12-01

This study compares CASS data to the externally assessed matric exam marks for a number of subjects. There are two signalling dimensions to inaccurate assessments: (i Inflated CASS marks can give students a false sense of security and lead to diminished exam effort. (ii A weak correlation between CASS and the exam marks could mean poor signalling in another dimension: Relatively good students may get relatively low CASS marks. Such low correlations indicate poor assessment reliability, as the examination and continuous assessment should both be testing mastery of the same national curriculum. The paper analyses the extent of each of these dimensions of weak signalling in South African schools and draws disturbing conclusions for a large part of the school system.

Major hazards onshore and offshore

International Nuclear Information System (INIS)

1992-01-01

This symposium continues the tradition of bringing together papers on a topic of current interest and importance in terms of process safety - in this case, Major Hazards Onshore and Offshore. Lord Cullen in his report on the Piper Alpha disaster has, in effect, suggested that the experience gained in the control of major hazards onshore during the 1980s should be applied to improve safety offshore during the 1990s. This major three-day symposium reviews what has been learned so far with regard to major hazards and considers its present and future applications both onshore and offshore. The topics covered in the programme are wide ranging and deal with all aspects of legislation, the application of regulations, techniques for evaluating hazards and prescribing safety measures in design, construction and operation, the importance of the human factors, and recent technical developments in protective measures, relief venting and predicting the consequences of fires and explosions. (author)

MGR External Events Hazards Analysis

International Nuclear Information System (INIS)

Booth, L.

1999-01-01

The purpose and objective of this analysis is to apply an external events Hazards Analysis (HA) to the License Application Design Selection Enhanced Design Alternative 11 [(LADS EDA II design (Reference 8.32))]. The output of the HA is called a Hazards List (HL). This analysis supersedes the external hazards portion of Rev. 00 of the PHA (Reference 8.1). The PHA for internal events will also be updated to the LADS EDA II design but under a separate analysis. Like the PHA methodology, the HA methodology provides a systematic method to identify potential hazards during the 100-year Monitored Geologic Repository (MGR) operating period updated to reflect the EDA II design. The resulting events on the HL are candidates that may have potential radiological consequences as determined during Design Basis Events (DBEs) analyses. Therefore, the HL that results from this analysis will undergo further screening and analysis based on the criteria that apply during the performance of DBE analyses

Hazardous waste disposal sites: Report 2

International Nuclear Information System (INIS)

1979-12-01

Arkansas, like virtually every other state, is faced with a deluge of hazardous waste. There is a critical need for increased hazardous waste disposal capacity to insure continued industrial development. Additionally, perpetual maintenance of closed hazardous waste disposal sites is essential for the protection of the environment and human health. Brief descriptions of legislative and regulatory action in six other states are provided in this report. A report prepared for the New York State Environmental Facilities Corp. outlines three broad approaches states may take in dealing with their hazardous waste disposal problems. These are described. State assistance in siting and post-closure maintenance, with private ownership of site and facility, appears to be the most advantageous option

9 CFR 316.12 - Marking of equine carcasses and parts thereof.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Marking of equine carcasses and parts... equine carcasses and parts thereof. (a) All inspected and passed equine carcasses and parts thereof... marking products in this part. (b) All equine carcasses and meat and other parts thereof shall be marked...

Mark Twain, Fenimore Cooper, and Batman.

Science.gov (United States)

Crick, Robert Alan

1992-01-01

Describes how Mark Twain's essay "Fenimore Cooper's Literary Offenses" helped students to get interested in writing and inspired them to write a similar essay critiquing the movie "Batman." Provides excerpts from students' essays. (PRA)

Linguistic gender marking and its international business ramifications

OpenAIRE

Estefania Santacreu-Vasut; Oded Shenkar; Amir Shoham

2014-01-01

We analyze the impact of language-based gender distinctions within languages’ grammatical structures on women’s corporate presence. Using four different data sets, we find that countries where the dominant language marks gender more intensely have significantly lower female participation on boards of directors and in senior management, as well as smaller female-led corporate teams. We also find that the gender marking of the language used in the headquarters’ home country impacts female prese...

List of external hazards to be considered in ASAMPSA-E

International Nuclear Information System (INIS)

Decker, Kurt; Brinkman, Hans

2016-01-01

The current report includes an exhaustive list of external hazards posing potential threats to nuclear installations. The list comprises of both, natural and man-made external hazards. Also, a cross correlation matrix of the hazards is presented. The list is the starting point for the hazard analysis process in Level 1 PSA as outlined by IAEA (2010; SSG-3) and the definition of design basis as required by WENRA (2014; Reference Levels for Existing Reactors). The list is regarded comprehensive by including all types of hazards that were previously cited in documents by IAEA and WENRA-RHWG. 73 natural hazards (N1 to N73) and 24 man-made external hazards (M1 to M24) are included. Natural hazards are grouped into seismo-tectonic hazards, flooding and hydrological hazards, extreme values of meteorological phenomena, rare meteorological phenomena, biological hazards / infestation, geological hazards, and forest fire. The list of external man-made hazards includes industry accidents, military accidents, transportation accidents, pipeline accidents and other man-made external events. The dataset further contains information on hazard correlations. 577 correlations between individual hazards are identified and shown in a cross-correlation chart. Correlations discriminate between: (1) Causally connected hazards (cause-effect relation) where one hazard (e.g., liquefaction) may be caused by another hazard (e.g., earthquake); or where one hazard (e.g., high wind) is a prerequisite for a correlated hazard (e.g., storm surge). (authors)

K Basins Hazard Analysis

International Nuclear Information System (INIS)

WEBB, R.H.

1999-01-01

This report describes the methodology used in conducting the K Basins Hazard Analysis, which provides the foundation for the K Basins Safety Analysis Report (HNF-SD-WM-SAR-062/Rev.4). This hazard analysis was performed in accordance with guidance provided by DOE-STD-3009-94, Preparation Guide for U. S. Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports and implements the requirements of DOE Order 5480.23, Nuclear Safety Analysis Report

Hazard Map for Autonomous Navigation

DEFF Research Database (Denmark)

Riis, Troels

This dissertation describes the work performed in the area of using image analysis in the process of landing a spacecraft autonomously and safely on the surface of the Moon. This is suggested to be done using a Hazard Map. The correspondence problem between several Hazard Maps are investigated...

Hazard classification or risk assessment

DEFF Research Database (Denmark)

Hass, Ulla

2013-01-01

The EU classification of substances for e.g. reproductive toxicants is hazard based and does not to address the risk suchsubstances may pose through normal, or extreme, use. Such hazard classification complies with the consumer's right to know. It is also an incentive to careful use and storage...

Hazardous waste. Annual report, 1984

International Nuclear Information System (INIS)

1985-01-01

Activities in the Hazardous Waste Program area in 1984 ranged from preparing management and long-range plans to arranging training seminars. Past and present generation of hazardous wastes were the key concerns. This report provides a summary of the significant events which took place in 1984. 6 tabs

Occupational health hazards in mining: an overview

Energy Technology Data Exchange (ETDEWEB)

Donoghue, A.M. [Alcoa World Alumina Australia, Perth, WA (Australia)

2004-08-01

This review article outlines the physical, chemical, biological, ergonomic and psychosocial occupational health hazards of mining and associated metallurgical processes. Mining remains an important industrial sector in many parts of the world and although substantial progress has been made in the control of occupational health hazards, there remains room for further risk reduction. This applies particularly to traumatic injury hazards, ergonomic hazards and noise. Vigilance is also required to ensure exposures to coal dust and crystalline silica remain effectively controlled.

Washington Tsunami Hazard Mitigation Program

Science.gov (United States)

Walsh, T. J.; Schelling, J.

2012-12-01

Washington State has participated in the National Tsunami Hazard Mitigation Program (NTHMP) since its inception in 1995. We have participated in the tsunami inundation hazard mapping, evacuation planning, education, and outreach efforts that generally characterize the NTHMP efforts. We have also investigated hazards of significant interest to the Pacific Northwest. The hazard from locally generated earthquakes on the Cascadia subduction zone, which threatens tsunami inundation in less than hour following a magnitude 9 earthquake, creates special problems for low-lying accretionary shoreforms in Washington, such as the spits of Long Beach and Ocean Shores, where high ground is not accessible within the limited time available for evacuation. To ameliorate this problem, we convened a panel of the Applied Technology Council to develop guidelines for construction of facilities for vertical evacuation from tsunamis, published as FEMA 646, now incorporated in the International Building Code as Appendix M. We followed this with a program called Project Safe Haven (http://www.facebook.com/ProjectSafeHaven) to site such facilities along the Washington coast in appropriate locations and appropriate designs to blend with the local communities, as chosen by the citizens. This has now been completed for the entire outer coast of Washington. In conjunction with this effort, we have evaluated the potential for earthquake-induced ground failures in and near tsunami hazard zones to help develop cost estimates for these structures and to establish appropriate tsunami evacuation routes and evacuation assembly areas that are likely to to be available after a major subduction zone earthquake. We intend to continue these geotechnical evaluations for all tsunami hazard zones in Washington.

Hazardous waste minimization tracking system

International Nuclear Information System (INIS)

Railan, R.

1994-01-01

Under RCRA section 3002 9(b) and 3005f(h), hazardous waste generators and owners/operators of treatment, storage, and disposal facilities (TSDFs) are required to certify that they have a program in place to reduce the volume or quantity and toxicity of hazardous waste to the degree determined to be economically practicable. In many cases, there are environmental, as well as, economic benefits, for agencies that pursue pollution prevention options. Several state governments have already enacted waste minimization legislation (e.g., Massachusetts Toxic Use Reduction Act of 1989, and Oregon Toxic Use Reduction Act and Hazardous Waste Reduction Act, July 2, 1989). About twenty six other states have established legislation that will mandate some type of waste minimization program and/or facility planning. The need to address the HAZMIN (Hazardous Waste Minimization) Program at government agencies and private industries has prompted us to identify the importance of managing The HAZMIN Program, and tracking various aspects of the program, as well as the progress made in this area. The open-quotes WASTEclose quotes is a tracking system, which can be used and modified in maintaining the information related to Hazardous Waste Minimization Program, in a manageable fashion. This program maintains, modifies, and retrieves information related to hazardous waste minimization and recycling, and provides automated report generating capabilities. It has a built-in menu, which can be printed either in part or in full. There are instructions on preparing The Annual Waste Report, and The Annual Recycling Report. The program is very user friendly. This program is available in 3.5 inch or 5 1/4 inch floppy disks. A computer with 640K memory is required

Automatic Extraction of Road Markings from Mobile Laser Scanning Data

Science.gov (United States)

Ma, H.; Pei, Z.; Wei, Z.; Zhong, R.

2017-09-01

Road markings as critical feature in high-defination maps, which are Advanced Driver Assistance System (ADAS) and self-driving technology required, have important functions in providing guidance and information to moving cars. Mobile laser scanning (MLS) system is an effective way to obtain the 3D information of the road surface, including road markings, at highway speeds and at less than traditional survey costs. This paper presents a novel method to automatically extract road markings from MLS point clouds. Ground points are first filtered from raw input point clouds using neighborhood elevation consistency method. The basic assumption of the method is that the road surface is smooth. Points with small elevation-difference between neighborhood are considered to be ground points. Then ground points are partitioned into a set of profiles according to trajectory data. The intensity histogram of points in each profile is generated to find intensity jumps in certain threshold which inversely to laser distance. The separated points are used as seed points to region grow based on intensity so as to obtain road mark of integrity. We use the point cloud template-matching method to refine the road marking candidates via removing the noise clusters with low correlation coefficient. During experiment with a MLS point set of about 2 kilometres in a city center, our method provides a promising solution to the road markings extraction from MLS data.

Microbial analysis of bite marks by sequence comparison of streptococcal DNA.

Directory of Open Access Journals (Sweden)

Darnell M Kennedy

Full Text Available Bite mark injuries often feature in violent crimes. Conventional morphometric methods for the forensic analysis of bite marks involve elements of subjective interpretation that threaten the credibility of this field. Human DNA recovered from bite marks has the highest evidentiary value, however recovery can be compromised by salivary components. This study assessed the feasibility of matching bacterial DNA sequences amplified from experimental bite marks to those obtained from the teeth responsible, with the aim of evaluating the capability of three genomic regions of streptococcal DNA to discriminate between participant samples. Bite mark and teeth swabs were collected from 16 participants. Bacterial DNA was extracted to provide the template for PCR primers specific for streptococcal 16S ribosomal RNA (16S rRNA gene, 16S-23S intergenic spacer (ITS and RNA polymerase beta subunit (rpoB. High throughput sequencing (GS FLX 454, followed by stringent quality filtering, generated reads from bite marks for comparison to those generated from teeth samples. For all three regions, the greatest overlaps of identical reads were between bite mark samples and the corresponding teeth samples. The average proportions of reads identical between bite mark and corresponding teeth samples were 0.31, 0.41 and 0.31, and for non-corresponding samples were 0.11, 0.20 and 0.016, for 16S rRNA, ITS and rpoB, respectively. The probabilities of correctly distinguishing matching and non-matching teeth samples were 0.92 for ITS, 0.99 for 16S rRNA and 1.0 for rpoB. These findings strongly support the tenet that bacterial DNA amplified from bite marks and teeth can provide corroborating information in the identification of assailants.

Nõmme maja "Kergus" : Kerese tn., Tallinn / Ülar Mark, Kalle Komissarov

Index Scriptorium Estoniae

Mark, Ülar

1999-01-01

Kahekorruselise, tänavapoolse pika umbse seinaga eramu projekteeris Arhitektuuribüroo Mark & Tamm, arhitekt Ülar Mark, kaasautor Kalle Komissarov. Konstruktiivne osa: Randväli & Karema Inseneribüroo. Projekt 1997, hoone valmis 1999. Eramu tähenduse ümbermõtestamisest. 13 illustratsiooni: korruste plaanid, välisvaated, sisevaade.Mark & Tamm (arhitektibüroo)

75 FR 60689 - Hazardous Waste Management System; Identification and Listing of Hazardous Waste; Proposed Rule

Science.gov (United States)

2010-10-01

... Waste Management System; Identification and Listing of Hazardous Waste; Proposed Rule AGENCY... exclude (or delist) a certain solid waste generated by its Beaumont, Texas, facility from the lists of hazardous wastes. EPA used the Delisting Risk Assessment Software (DRAS) Version 3.0 in the evaluation of...

Transcription factors, coregulators, and epigenetic marks are linearly correlated and highly redundant.

Directory of Open Access Journals (Sweden)

Tobias Ahsendorf

Full Text Available The DNA microstates that regulate transcription include sequence-specific transcription factors (TFs, coregulatory complexes, nucleosomes, histone modifications, DNA methylation, and parts of the three-dimensional architecture of genomes, which could create an enormous combinatorial complexity across the genome. However, many proteins and epigenetic marks are known to colocalize, suggesting that the information content encoded in these marks can be compressed. It has so far proved difficult to understand this compression in a systematic and quantitative manner. Here, we show that simple linear models can reliably predict the data generated by the ENCODE and Roadmap Epigenomics consortia. Further, we demonstrate that a small number of marks can predict all other marks with high average correlation across the genome, systematically revealing the substantial information compression that is present in different cell lines. We find that the linear models for activating marks are typically cell line-independent, while those for silencing marks are predominantly cell line-specific. Of particular note, a nuclear receptor corepressor, transducin beta-like 1 X-linked receptor 1 (TBLR1, was highly predictive of other marks in two hematopoietic cell lines. The methodology presented here shows how the potentially vast complexity of TFs, coregulators, and epigenetic marks at eukaryotic genes is highly redundant and that the information present can be compressed onto a much smaller subset of marks. These findings could be used to efficiently characterize cell lines and tissues based on a small number of diagnostic marks and suggest how the DNA microstates, which regulate the expression of individual genes, can be specified.

27 CFR 26.207 - Destruction of marks and brands.

Science.gov (United States)

2010-04-01

... brands. 26.207 Section 26.207 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE... Products Coming Into the United States From the Virgin Islands § 26.207 Destruction of marks and brands. The marks, brands, and serial numbers required by this part to be placed on barrels, casks, or similar...

27 CFR 26.41 - Destruction of marks and brands.

Science.gov (United States)

2010-04-01

... brands. 26.41 Section 26.41 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE... Products Coming Into the United States From Puerto Rico § 26.41 Destruction of marks and brands. The marks, brands, and serial numbers required by this part to be placed on barrels, casks, or similar containers...

15 CFR 16.10 - The Department of Commerce Mark.

Science.gov (United States)

2010-01-01

... 15 Commerce and Foreign Trade 1 2010-01-01 2010-01-01 false The Department of Commerce Mark. 16.10 Section 16.10 Commerce and Foreign Trade Office of the Secretary of Commerce PROCEDURES FOR A VOLUNTARY CONSUMER PRODUCT INFORMATION LABELING PROGRAM § 16.10 The Department of Commerce Mark. The Department of...

A Novel Marking Reader for Progressive Addition Lenses Based on Gabor Holography.

Science.gov (United States)

Perucho, Beatriz; Picazo-Bueno, José Angel; Micó, Vicente

2016-05-01

Progressive addition lenses (PALs) are marked with permanent engraved marks (PEMs) at standardized locations. Permanent engraved marks are very useful through the manufacturing and mounting processes, act as locator marks to re-ink the removable marks, and contain useful information about the PAL. However, PEMs are often faint and weak, obscured by scratches, partially occluded, and difficult to recognize on tinted lenses or with antireflection or scratch-resistant coatings. The aim of this article is to present a new generation of portable marking reader based on an extremely simplified concept for visualization and identification of PEMs in PALs. Permanent engraved marks on different PALs are visualized using classical Gabor holography as underlying principle. Gabor holography allows phase sample visualization with adjustable magnification and can be implemented in either classical or digital versions. Here, visual Gabor holography is used to provide a magnified defocused image of the PEMs onto a translucent visualization screen where the PEM is clearly identified. Different types of PALs (conventional, personalized, old and scratched, sunglasses, etc.) have been tested to visualize PEMs with the proposed marking reader. The PEMs are visible in every case, and variable magnification factor can be achieved simply moving up and down the PAL in the instrument. In addition, a second illumination wavelength is also tested, showing the applicability of this novel marking reader for different illuminations. A new concept of marking reader ophthalmic instrument has been presented and validated in the laboratory. The configuration involves only a commercial-grade laser diode and a visualization screen for PEM identification. The instrument is portable, economic, and easy to use, and it can be used for identifying patient's current PAL model and for marking removable PALs again or finding test points regardless of the age of the PAL, its scratches, tints, or coatings.

FEMA Hazard Mitigation Grants Program Summary

Data.gov (United States)

Department of Homeland Security — The Hazard Mitigation Grant Program (HMGP, CFDA Number: 97.039) provides grants to States and local governments to implement long-term hazard mitigation measures...

Energy and solid/hazardous waste

Energy Technology Data Exchange (ETDEWEB)

None

1981-12-01

This report addresses the past and potential future solid and hazardous waste impacts from energy development, and summarizes the major environmental, legislation applicable to solid and hazardous waste generation and disposal. A glossary of terms and acronyms used to describe and measure solid waste impacts of energy development is included. (PSB)

Energy and solid/hazardous waste

International Nuclear Information System (INIS)

1981-12-01

This report addresses the past and potential future solid and hazardous waste impacts from energy development, and summarizes the major environmental, legislation applicable to solid and hazardous waste generation and disposal. A glossary of terms and acronyms used to describe and measure solid waste impacts of energy development is included

27 CFR 22.33 - Time of destruction of marks and brands.

Science.gov (United States)

2010-04-01

... marks and brands. 22.33 Section 22.33 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND... Provisions Destruction of Marks and Brands § 22.33 Time of destruction of marks and brands. (a) Any person..., brand, and labels required by this chapter to be placed on packages of tax-free alcohol. (b) A person...

Quantum Query Complexity for Searching Multiple Marked States from an Unsorted Database

International Nuclear Information System (INIS)

Shang Bin

2007-01-01

An important and usual sort of search problems is to find all marked states from an unsorted database with a large number of states. Grover's original quantum search algorithm is for finding single marked state with uncertainty, and it has been generalized to the case of multiple marked states, as well as been modified to find single marked state with certainty. However, the query complexity for finding all multiple marked states has not been addressed. We use a generalized Long's algorithm with high precision to solve such a problem. We calculate the approximate query complexity, which increases with the number of marked states and with the precision that we demand. In the end we introduce an algorithm for the problem on a 'duality computer' and show its advantage over other algorithms.

Marking behavior of the giant anteater Myrmecophaga tridactyla (Mammalia: Myrmecophagidae in Southern Brazil

Directory of Open Access Journals (Sweden)

Fernanda G. Braga

2010-02-01

Full Text Available This research presents novel data on tree marking by the giant anteater, a large Neotropical mammal threatened in the state of Paraná and other areas of Brazil, and nearly threatened worldwide. Field work was carried out in the municipality of Jaguariaíva, Paraná (Southern Brazil with the goal of evaluating the pine marking behavior of the giant anteater and ascertaining whether wildfires interfere with it. Anteater marks were searched for on the trunks of pine trees in stands as well as pine trees dispersed throughout the landscape. For each pine tree, the following features were recorded: height, diameter breast height (DBH, height of first branch, presence/absence of scratch marks, geographical location, substrate, and matrix. The total number of scratches, scratch directions, scratch length, and height of top mark were also recorded. The scratches were defined as horizontal or vertical. Tree scratching was directly observed in three instances. Ninety-one trees were measured in the study area. The differences between marked and non-marked pines were significant for DBH and height of first branch. All scratches were found on pines dispersed throughout the landscape. Trees with horizontal and vertical marks were significantly different in terms of DBH, first branch height, and top mark height. After a wildfire that affected part of the study area, 54% of the previously marked trees were marked anew. We suggest that the marking behavior is used for communication between conspecifics with overlapping home ranges, possibly during the mating season. Additionally, we advance the hypothesis that pine marking behavior becomes more frequent with increased population stress due to anthropic interference.

14 CFR 139.337 - Wildlife hazard management.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Wildlife hazard management. 139.337 Section... AIRPORTS Operations § 139.337 Wildlife hazard management. (a) In accordance with its Airport Certification... alleviate wildlife hazards whenever they are detected. (b) In a manner authorized by the Administrator, each...

Transport of hazardous goods. Befoerderung gefaehrlicher Gueter

Energy Technology Data Exchange (ETDEWEB)

1989-01-01

The course 'Transport of hazardous goods' was held in Berlin in November 1988 in cooperation with the Bundesanstalt fuer Materialforschung und -pruefung. From all lecturs, two are recorded separately: 'Safety of tank trucks - requirements on the tank, development possibiities of active and passive safety' and 'Requirements on the transport of radioactive materials - possible derivations for other hazardous goods'. The other lectures deal with hazardous goods law, requirements on packinging, risk assessment, railroad transport, hazardous goods road network, insurance matters, EC regulations, and waste tourism. (HSCH).

Identifikasi bite marks dengan ekstraksi DNA metode Chelex (Bite marks identification with Chelex methods in DNA extraction

Directory of Open Access Journals (Sweden)

Imelda Kristina Sutrisno

2013-06-01

Full Text Available Background: In the case of crime often encountered evidence in bite marks form that was found on the victim’s body. Generally, bitemarks identification use standard techniques that compare the interpretation picture with the tooth model of suspected person. However, sometimes the techniques do not obtain accurate results. Therefore another technique is needed to support the identification process,such as DNA analysis that use the remaining epithelium attached in saliva to identify the DNA of the suspected person. In this processes a limited DNA material could be met, not only less in quantity but also less in quality. Chelex known as one of an effective DNA extraction method in DNA forensic case is needed to overcome this problem. Purpose: The study was aimed to examine the use of Chelex as DNA extraction method on a bitemarks sample models. Methods: The blood and bitemarks of 5 persons with were taken. The DNA of each subject was exctracted with Chelex and quantified the quantity with UV Spechtrophotometer. The DNA results was amplified by PCR at locus vWA and TH01 then vizualised by electrophoresis. Results: The electrophoresis’s results showed band at locus vWA and TH01 for blood sample and bite marks with no significant differences. Conclusion: The study showed that Chelex method could be use to extract DNA from bitemarks.Latar belakang: Dalam kasus kejahatan sering dijumpai bukti dalam bentuk bekas gigitan (bitemarks yang ditemukan pada tubuh korban. Umumnya, untuk mengidentifikasi bite marks menggunakan teknik standar yaitu membandingkan foto interpretasi dengan model gigi dari orang yang dicurigai. Namun demikian teknik ini terkadang tidak mendapatkan hasil yang akurat, sehingga diperlukan teknik lain untuk menunjang keberhasilan proses identifikasi pelaku, yakni melalui analisis DNA bitemarks, yang diperoleh dari saliva yang mengandung sisa epitel tersangka pelaku. Sampel DNA yang berasal dari bitemarks umumnya terbatas, tidak hanya

Hazard index for underground toxic material

International Nuclear Information System (INIS)

Smith, C.F.; Cohen, J.J.; McKone, T.E.

1980-06-01

To adequately define the problem of waste management, quantitative measures of hazard must be used. This study reviews past work in the area of hazard indices and proposes a geotoxicity hazard index for use in characterizing the hazard of toxic material buried underground. Factors included in this index are: an intrinsic toxicity factor, formulated as the volume of water required for dilution to public drinking-water levels; a persistence factor to characterize the longevity of the material, ranging from unity for stable materials to smaller values for shorter-lived materials; an availability factor that relates the transport potential for the particular material to a reference value for its naturally occurring analog; and a correction factor to accommodate the buildup of decay progeny, resulting in increased toxicity

Hazard index for underground toxic material

Energy Technology Data Exchange (ETDEWEB)

Smith, C.F.; Cohen, J.J.; McKone, T.E.

1980-06-01

To adequately define the problem of waste management, quantitative measures of hazard must be used. This study reviews past work in the area of hazard indices and proposes a geotoxicity hazard index for use in characterizing the hazard of toxic material buried underground. Factors included in this index are: an intrinsic toxicity factor, formulated as the volume of water required for dilution to public drinking-water levels; a persistence factor to characterize the longevity of the material, ranging from unity for stable materials to smaller values for shorter-lived materials; an availability factor that relates the transport potential for the particular material to a reference value for its naturally occurring analog; and a correction factor to accommodate the buildup of decay progeny, resulting in increased toxicity.

Modeling and Hazard Analysis Using STPA

Science.gov (United States)

Ishimatsu, Takuto; Leveson, Nancy; Thomas, John; Katahira, Masa; Miyamoto, Yuko; Nakao, Haruka

2010-09-01

A joint research project between MIT and JAXA/JAMSS is investigating the application of a new hazard analysis to the system and software in the HTV. Traditional hazard analysis focuses on component failures but software does not fail in this way. Software most often contributes to accidents by commanding the spacecraft into an unsafe state(e.g., turning off the descent engines prematurely) or by not issuing required commands. That makes the standard hazard analysis techniques of limited usefulness on software-intensive systems, which describes most spacecraft built today. STPA is a new hazard analysis technique based on systems theory rather than reliability theory. It treats safety as a control problem rather than a failure problem. The goal of STPA, which is to create a set of scenarios that can lead to a hazard, is the same as FTA but STPA includes a broader set of potential scenarios including those in which no failures occur but the problems arise due to unsafe and unintended interactions among the system components. STPA also provides more guidance to the analysts that traditional fault tree analysis. Functional control diagrams are used to guide the analysis. In addition, JAXA uses a model-based system engineering development environment(created originally by Leveson and called SpecTRM) which also assists in the hazard analysis. One of the advantages of STPA is that it can be applied early in the system engineering and development process in a safety-driven design process where hazard analysis drives the design decisions rather than waiting until reviews identify problems that are then costly or difficult to fix. It can also be applied in an after-the-fact analysis and hazard assessment, which is what we did in this case study. This paper describes the experimental application of STPA to the JAXA HTV in order to determine the feasibility and usefulness of the new hazard analysis technique. Because the HTV was originally developed using fault tree analysis

Seismic hazard assessment of the Province of Murcia (SE Spain): analysis of source contribution to hazard

Science.gov (United States)

García-Mayordomo, J.; Gaspar-Escribano, J. M.; Benito, B.

2007-10-01

A probabilistic seismic hazard assessment of the Province of Murcia in terms of peak ground acceleration (PGA) and spectral accelerations [SA( T)] is presented in this paper. In contrast to most of the previous studies in the region, which were performed for PGA making use of intensity-to-PGA relationships, hazard is here calculated in terms of magnitude and using European spectral ground-motion models. Moreover, we have considered the most important faults in the region as specific seismic sources, and also comprehensively reviewed the earthquake catalogue. Hazard calculations are performed following the Probabilistic Seismic Hazard Assessment (PSHA) methodology using a logic tree, which accounts for three different seismic source zonings and three different ground-motion models. Hazard maps in terms of PGA and SA(0.1, 0.2, 0.5, 1.0 and 2.0 s) and coefficient of variation (COV) for the 475-year return period are shown. Subsequent analysis is focused on three sites of the province, namely, the cities of Murcia, Lorca and Cartagena, which are important industrial and tourism centres. Results at these sites have been analysed to evaluate the influence of the different input options. The most important factor affecting the results is the choice of the attenuation relationship, whereas the influence of the selected seismic source zonings appears strongly site dependant. Finally, we have performed an analysis of source contribution to hazard at each of these cities to provide preliminary guidance in devising specific risk scenarios. We have found that local source zones control the hazard for PGA and SA( T ≤ 1.0 s), although contribution from specific fault sources and long-distance north Algerian sources becomes significant from SA(0.5 s) onwards.

Robots, systems, and methods for hazard evaluation and visualization

Science.gov (United States)

Nielsen, Curtis W.; Bruemmer, David J.; Walton, Miles C.; Hartley, Robert S.; Gertman, David I.; Kinoshita, Robert A.; Whetten, Jonathan

2013-01-15

A robot includes a hazard sensor, a locomotor, and a system controller. The robot senses a hazard intensity at a location of the robot, moves to a new location in response to the hazard intensity, and autonomously repeats the sensing and moving to determine multiple hazard levels at multiple locations. The robot may also include a communicator to communicate the multiple hazard levels to a remote controller. The remote controller includes a communicator for sending user commands to the robot and receiving the hazard levels from the robot. A graphical user interface displays an environment map of the environment proximate the robot and a scale for indicating a hazard intensity. A hazard indicator corresponds to a robot position in the environment map and graphically indicates the hazard intensity at the robot position relative to the scale.

Volcanic Hazards in Site Evaluation for Nuclear Installations

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-10-15

This publication provides comprehensive and updated guidance for site evaluation in relation to volcanic hazards. It includes recommendations on assessing the volcanic hazards at a nuclear installation site, in order to identify and characterize, in a comprehensive manner, all potentially hazardous phenomena that may be associated with future volcanic events. It describes how some of these volcanic phenomena may affect the acceptability of the selected site, resulting in exclusion of a site or determining the corresponding design basis parameters for the installation. This Safety Guide is applicable to both existing and new sites, and a graded approach is recommended to cater for all types of nuclear installations. Contents: 1. Introduction; 2. Overview of volcanic hazard assessment; 3. General recommendations; 4. Necessary information and investigations (database); 5. Screening of volcanic hazards; 6. Site specific volcanic hazard assessment; 7. Nuclear installations other than nuclear power plants; 8. Monitoring and preparation for response; 9. Management system for volcanic hazard assessment; Annex I: Volcanic hazard scenarios; Annex II: Worldwide sources of information.

Overview of hazardous-waste regulation at federal facilities

International Nuclear Information System (INIS)

Tanzman, E.; LaBrie, B.; Lerner, K.

1982-05-01

This report is organized in a fashion that is intended to explain the legal duties imposed on officials responsible for hazardous waste at each stage of its existence. Section 2 describes federal hazardous waste laws, explaining the legal meaning of hazardous waste and the protective measures that are required to be taken by its generators, transporters, and storers. In addition, penalties for violation of the standards are summarized, and a special discussion is presented of so-called imminent hazard provisions for handling hazardous waste that immediately threatens public health and safety. Although the focus of Sec. 2 is on RCRA, which is the principal federal law regulating hazardous waste, other federal statutes are discussed as appropriate. Section 3 covers state regulation of hazardous waste. First, Sec. 3 explains the system of state enforcement of the federal RCRA requirements on hazardous waste within their borders. Second, Sec. 3 discusses two peculiar provisions of RCRA that appear to permit states to regulate federal facilities more strictly than RCRA otherwise would require

Overview of hazardous-waste regulation at federal facilities

Energy Technology Data Exchange (ETDEWEB)

Tanzman, E.; LaBrie, B.; Lerner, K.

1982-05-01

This report is organized in a fashion that is intended to explain the legal duties imposed on officials responsible for hazardous waste at each stage of its existence. Section 2 describes federal hazardous waste laws, explaining the legal meaning of hazardous waste and the protective measures that are required to be taken by its generators, transporters, and storers. In addition, penalties for violation of the standards are summarized, and a special discussion is presented of so-called imminent hazard provisions for handling hazardous waste that immediately threatens public health and safety. Although the focus of Sec. 2 is on RCRA, which is the principal federal law regulating hazardous waste, other federal statutes are discussed as appropriate. Section 3 covers state regulation of hazardous waste. First, Sec. 3 explains the system of state enforcement of the federal RCRA requirements on hazardous waste within their borders. Second, Sec. 3 discusses two peculiar provisions of RCRA that appear to permit states to regulate federal facilities more strictly than RCRA otherwise would require.

Radioactive marking of proteins in cultured mouse embryos

International Nuclear Information System (INIS)

Nowak, J.

1984-01-01

The purpose of this work was to build an in vitro test system, with which on the one hand postimplantation embryos of the mouse could be cultured without morphological of physiological damage and on the other hand their protein could be as highly marked as possible. With this radioactively marked proteins were to be won, which are optimally suited for a high separation by two-dimensional electrophoresis. In addition incubation and preparation methods were found for the ages of day 10, 11 and 12 of the embryonic development. With the use of 3 H-marked amino acids in the culture medium it was determined that embryos without embryonic membranes, so-called N-embryos, built in more radioactivity into their proteins than the embryos with embryonic membranes, the so-called DAO-embryos or the DO-embryos. On the contrary, the embryos with intact blood circulation (DO-embryos) showed an even distribution of radioactive marker in their bodies. Since an even distribution of the marker in the embryo is a necessary prerequisite for a representative presentation of the proteins by 2DE, the DO-preparation was considered the best suited method. In order to increase the amount of radioactivity incorporated into the proteins of the DO-embryos, the concentration of the used isotope or the incubation length could be increased. A combination of both proved to be the best method. A 14 C-marked amino acid mixture of 20 μCi/corresponds to 20 μl instead of the usual 150 μCi 3 H-marked amino acids in a culture medium proved to be equally suitable. Notable changes which would have indicated a damaging affect of the used radioactivity or the in vitro culturing were not observed. The achieved methodical conditions were used for the presentation of the embryo proteins by two-dimensional electrophoresis and fluorography. (orig./MG) [de

222 S Laboratory complex hazards assessment

International Nuclear Information System (INIS)

Sutton, L.N.

1998-01-01

This report documents the hazards assessment for the 222-S Analytical Laboratory located on the US Department of Energy (DOE) Hanford Site. Operation of the laboratory is the responsibility of Waste Management Federal Services, Inc. (WMFS). This hazards assessment was conducted to provide the emergency planning technical basis for the 222-S Facility. DOE Orders require an emergency planning hazards assessment for each facility that has the potential to reach or exceed the lowest level emergency classification

Hazardous fluid leak detector

Science.gov (United States)

Gray, Harold E.; McLaurin, Felder M.; Ortiz, Monico; Huth, William A.

1996-01-01

A device or system for monitoring for the presence of leaks from a hazardous fluid is disclosed which uses two electrodes immersed in deionized water. A gas is passed through an enclosed space in which a hazardous fluid is contained. Any fumes, vapors, etc. escaping from the containment of the hazardous fluid in the enclosed space are entrained in the gas passing through the enclosed space and transported to a closed vessel containing deionized water and two electrodes partially immersed in the deionized water. The electrodes are connected in series with a power source and a signal, whereby when a sufficient number of ions enter the water from the gas being bubbled through it (indicative of a leak), the water will begin to conduct, thereby allowing current to flow through the water from one electrode to the other electrode to complete the circuit and activate the signal.

Moral Hazard in Pediatrics.

Science.gov (United States)

Brunnquell, Donald; Michaelson, Christopher M

2016-07-01

"Moral hazard" is a term familiar in economics and business ethics that illuminates why rational parties sometimes choose decisions with bad moral outcomes without necessarily intending to behave selfishly or immorally. The term is not generally used in medical ethics. Decision makers such as parents and physicians generally do not use the concept or the word in evaluating ethical dilemmas. They may not even be aware of the precise nature of the moral hazard problem they are experiencing, beyond a general concern for the patient's seemingly excessive burden. This article brings the language and logic of moral hazard to pediatrics. The concept reminds us that decision makers in this context are often not the primary party affected by their decisions. It appraises the full scope of risk at issue when decision makers decide on behalf of others and leads us to separate, respect, and prioritize the interests of affected parties.

Hazardous material reduction initiative

International Nuclear Information System (INIS)

Nichols, D.H.

1995-02-01

The Hazardous Material Reduction Initiative (HMRI) explores using the review of purchase requisitions to reduce both the use of hazardous materials and the generation of regulated and nonregulated wastes. Based on an 11-month program implemented at the Hanford Site, hazardous material use and waste generation was effectively reduced by using a centralized procurement control program known as HMRI. As expected, several changes to the original proposal were needed during the development/testing phase of the program to accommodate changing and actual conditions found at the Hanford Site. The current method requires a central receiving point within the Procurement Organization to review all purchase requisitions for potentially Occupational Safety and Health Administration (OSHA) hazardous products. Those requisitions (approximately 4% to 6% of the total) are then forwarded to Pollution Prevention personnel for evaluation under HMRI. The first step is to determine if the requested item can be filled by existing or surplus material. The requisitions that cannot filled by existing or surplus material are then sorted into two groups based on applicability to the HMRI project. For example, laboratory requests for analytical reagents or standards are excluded and the purchase requisitions are returned to Procurement for normal processing because, although regulated, there is little opportunity for source reduction due to the strict protocols followed. Each item is then checked to determine if it is regulated or not. Regulated items are prioritized based on hazardous contents, quantity requested, and end use. Copies of these requisitions are made and the originals are returned to Procurement within 1-hr. Since changes to the requisition can be made at later stages during procurement, the HMRI fulfills one of its original premises in that it does not slow the procurement process

49 CFR 659.31 - Hazard management process.

Science.gov (United States)

2010-10-01

... 49 Transportation 7 2010-10-01 2010-10-01 false Hazard management process. 659.31 Section 659.31... Agency § 659.31 Hazard management process. (a) The oversight agency must require the rail transit agency..., operational changes, or other changes within the rail transit environment. (b) The hazard management process...

An industry-scale mass marking technique for tracing farmed fish escapees.

Directory of Open Access Journals (Sweden)

Fletcher Warren-Myers

Full Text Available Farmed fish escape and enter the environment with subsequent effects on wild populations. Reducing escapes requires the ability to trace individuals back to the point of escape, so that escape causes can be identified and technical standards improved. Here, we tested if stable isotope otolith fingerprint marks delivered during routine vaccination could be an accurate, feasible and cost effective marking method, suitable for industrial-scale application. We tested seven stable isotopes, (134Ba, (135Ba, (136Ba, (137Ba, (86Sr, (87Sr and (26Mg, on farmed Atlantic salmon reared in freshwater, in experimental conditions designed to reflect commercial practice. Marking was 100% successful with individual Ba isotopes at concentrations as low as 0.001 µg. g-1 fish and for Sr isotopes at 1 µg. g-1 fish. Our results suggest that 63 unique fingerprint marks can be made at low cost using Ba (0.0002 - 0.02 $US per mark and Sr (0.46 - 0.82 $US per mark isotopes. Stable isotope fingerprinting during vaccination is feasible for commercial application if applied at a company level within the world's largest salmon producing nations. Introducing a mass marking scheme would enable tracing of escapees back to point of origin, which could drive greater compliance, better farm design and improved management practices to reduce escapes.

75 FR 67919 - Hazardous Waste Management System; Proposed Exclusion for Identifying and Listing Hazardous Waste

Science.gov (United States)

2010-11-04

... treatment sludge from the lists of hazardous waste set forth in Title 40 of the Code of Federal Regulations... treatment sludges generated at its facility located in Owosso, Michigan from the list of hazardous wastes... disposed in a Subtitle D landfill and we considered transport of waste constituents through ground water...

Evaluation of soil bioassays for use at Washington state hazardous waste sites: A pilot study

International Nuclear Information System (INIS)

Blakley, N.; Norton, D.; Stinson, M.; Boyer, R.

1994-01-01

The Washington State Department of Ecology (Ecology) is developing guidelines to assess soil toxicity at hazardous waste sites being investigated under the Washington Model Toxics Control Act Cleanup Regulation. To evaluate soil toxicity, Ecology selected five bioassay protocols -- Daphnia, Earthworm, Seedling, Fathead Minnow, and Frog Embryo Teratogenesis Assay Xenopus (FETAX) -- for use as screening level assessment tools at six State hazardous waste sites. Sites contained a variety of contaminants including metals, creosote, pesticides, and petroleum products (leaking underground storage tanks). Three locations, representing high, medium, and low levels of contamination, were samples at each site. In general, the high contaminant samples resulted in the highest toxic response in all bioassays. The order of site toxicity, as assessed by overall toxic response, is creosote, petroleum products, metals, and pesticides. Results indicate that human health standards, especially for metals, may not adequately protect some of the species tested. The FETAX bioassay had the greatest overall number of toxic responses and lowest variance. The seedling and Daphnia bioassays had lower and similar overall toxic response results, followed by the earthworm and fathead minnow. Variability was markedly highest for the seedling. The Daphnia and fathead minnow variability were similar to the FETAX level, while the earthworm variability was slightly higher

46 CFR 160.054-6 - Marking.

Science.gov (United States)

2010-10-01

... “To Close, Press Together Full Length”. The marking may be applied to the container by the silk screen process, using a suitable ink or paint, or may be applied by other means shown to be acceptable. (b...

Mark's story as oral traditional literature: Rethinking the transmission ...

African Journals Online (AJOL)

The interpretation of Mark's gospel is inextricably linked to a conception of the gospel's genesis. By basing his argument on an aspect of the 'oral formulaic theory' the author of this paper argues that Mark's gospel can be seen as an example of oral traditional composition. The primary asset of this perspective is that it ...

A Trust-Based Adaptive Probability Marking and Storage Traceback Scheme for WSNs

Science.gov (United States)

Liu, Anfeng; Liu, Xiao; Long, Jun

2016-01-01

Security is a pivotal issue for wireless sensor networks (WSNs), which are emerging as a promising platform that enables a wide range of military, scientific, industrial and commercial applications. Traceback, a key cyber-forensics technology, can play an important role in tracing and locating a malicious source to guarantee cybersecurity. In this work a trust-based adaptive probability marking and storage (TAPMS) traceback scheme is proposed to enhance security for WSNs. In a TAPMS scheme, the marking probability is adaptively adjusted according to the security requirements of the network and can substantially reduce the number of marking tuples and improve network lifetime. More importantly, a high trust node is selected to store marking tuples, which can avoid the problem of marking information being lost. Experimental results show that the total number of marking tuples can be reduced in a TAPMS scheme, thus improving network lifetime. At the same time, since the marking tuples are stored in high trust nodes, storage reliability can be guaranteed, and the traceback time can be reduced by more than 80%. PMID:27043566

Hazard sign comprehension among illiterate adults

African Journals Online (AJOL)

KATEVG

Hazard signs have been considered an effective mode of transferring safety .... United Kingdom and the United States of America, indicating that hazard ..... primary providers of these programmes (Occupational Health and Safety Act 1993).

AUTOMATIC EXTRACTION OF ROAD MARKINGS FROM MOBILE LASER SCANNING DATA

Directory of Open Access Journals (Sweden)

H. Ma

2017-09-01

Full Text Available Road markings as critical feature in high-defination maps, which are Advanced Driver Assistance System (ADAS and self-driving technology required, have important functions in providing guidance and information to moving cars. Mobile laser scanning (MLS system is an effective way to obtain the 3D information of the road surface, including road markings, at highway speeds and at less than traditional survey costs. This paper presents a novel method to automatically extract road markings from MLS point clouds. Ground points are first filtered from raw input point clouds using neighborhood elevation consistency method. The basic assumption of the method is that the road surface is smooth. Points with small elevation-difference between neighborhood are considered to be ground points. Then ground points are partitioned into a set of profiles according to trajectory data. The intensity histogram of points in each profile is generated to find intensity jumps in certain threshold which inversely to laser distance. The separated points are used as seed points to region grow based on intensity so as to obtain road mark of integrity. We use the point cloud template-matching method to refine the road marking candidates via removing the noise clusters with low correlation coefficient. During experiment with a MLS point set of about 2 kilometres in a city center, our method provides a promising solution to the road markings extraction from MLS data.

Hazards associated with stage one-mining

International Nuclear Information System (INIS)

Anon.

1975-01-01

Radiation hazards in uranium mining arise from the presence of radon-222, a gas which can escape from exposed rock surfaces into the air. Radon daughter products have been associated with an increased incidence of respiratory lung cancer. Other hazards include the tailings which arise from the extraction of uranium ores. The tailings still contain most of the original radium and emit gamma rays and radon gas. The hazards associated with uranium enrichment and fuel manufacture are also discussed. (R.L.)

Hazard evaluation and risk management

International Nuclear Information System (INIS)

Fritzsche, A.F.

1986-01-01

The eigth chapter deals with the actual handling of hazards. The principal issue concerns man's behaviour towards hazards as an individual formerly and today; the evaluation of expected results of both a positive and a negative kind as determined by the individual's values which may differ and vary greatly from one individual to the next. The evaluation of benefit and hazard as well as the risk management resulting from decision-taking are political processes in the democratic state. Formal decision-taking tools play a major role in this process which concerns such central issues like who will participate; how the decision is arrived at; the participation of citizens; specialist knowledge and participation of the general public. (HSCH) [de

3D road marking reconstruction from street-level calibrated stereo pairs

Science.gov (United States)

Soheilian, Bahman; Paparoditis, Nicolas; Boldo, Didier

This paper presents an automatic approach to road marking reconstruction using stereo pairs acquired by a mobile mapping system in a dense urban area. Two types of road markings were studied: zebra crossings (crosswalks) and dashed lines. These two types of road markings consist of strips having known shape and size. These geometric specifications are used to constrain the recognition of strips. In both cases (i.e. zebra crossings and dashed lines), the reconstruction method consists of three main steps. The first step extracts edge points from the left and right images of a stereo pair and computes 3D linked edges using a matching process. The second step comprises a filtering process that uses the known geometric specifications of road marking objects. The goal is to preserve linked edges that can plausibly belong to road markings and to filter others out. The final step uses the remaining linked edges to fit a theoretical model to the data. The method developed has been used for processing a large number of images. Road markings are successfully and precisely reconstructed in dense urban areas under real traffic conditions.

Study of gunshot residues from Sintox® ammunition containing marking substances

Directory of Open Access Journals (Sweden)

Júlia Polovková

2015-12-01

Full Text Available Two types of factory marked Sintox® ammunition were investigated from the composition of gunshot residue particles (GSR and occurrence of marking substance points of view. The experiments were carried out with two cartridges of caliber 9 mm Luger (9 × 19 Parabellum of two producers (Ruag Ammotec, Switzerland and Men, Germany. The first cartridge (type Action 4, Ruag Ammotec contains gadolinium as a marking element, while the other cartridge (type PEP II, Men is marked with gallium in gunpowder. Scanning electron microscopy equipped with EDAX analyzer (SEM/EDX was used to detect and analyze the GSR particles in samples collected from the cartridges, barrels and shooter’s hands. Besides those, particles from the hit clothes placed at different shooting distances were collected and analyzed. The spreading of GSR cloud from the gun was observed using the high-speed camera. Results obtained clearly revealed that the way of ammunition production/construction and type of marking of ammunition can significantly influence the presence and detection reliability of marking elements in GSR. The detectability is affected also by the shooting distance.

Protecting the turf: The effect of territorial marking on others' creativity.

Science.gov (United States)

Brown, Graham; Baer, Markus

2015-11-01

Territorial marking allows people to communicate that a territory has been claimed. Across 2 studies, we examine the impact of territorial marking of one's ideas on others' invited creativity when asked to provide feedback. Integrating research on territoriality and self-construal, we examine the effect of control-oriented marking on invited creativity (Study 1), and the extent to which an independent versus interdependent self-construal moderates this effect (Study 2). Results of Study 1 demonstrate that the use of control-oriented marking to communicate a territorial claim over one's ideas inhibits invited creativity, and this effect is mediated by intrinsic motivation. Also consistent with our hypotheses, the results of Study 2 show that self-construal moderates the effect of control-oriented marking on others' intrinsic motivation and creativity. Marking diminishes invited creativity among people with an independent self-construal but serves to enhance the creativity of those with an interdependent self-construal. Consistent with Study 1, intrinsic motivation mediates this moderated effect. Our results highlight the important but heretofore understudied role of territoriality in affecting others' creativity as well as the role of independent versus interdependent self-construal in shaping this effect. (c) 2015 APA, all rights reserved).

A probabilistic tsunami hazard assessment for Indonesia

Science.gov (United States)

Horspool, N.; Pranantyo, I.; Griffin, J.; Latief, H.; Natawidjaja, D. H.; Kongko, W.; Cipta, A.; Bustaman, B.; Anugrah, S. D.; Thio, H. K.

2014-11-01

Probabilistic hazard assessments are a fundamental tool for assessing the threats posed by hazards to communities and are important for underpinning evidence-based decision-making regarding risk mitigation activities. Indonesia has been the focus of intense tsunami risk mitigation efforts following the 2004 Indian Ocean tsunami, but this has been largely concentrated on the Sunda Arc with little attention to other tsunami prone areas of the country such as eastern Indonesia. We present the first nationally consistent probabilistic tsunami hazard assessment (PTHA) for Indonesia. This assessment produces time-independent forecasts of tsunami hazards at the coast using data from tsunami generated by local, regional and distant earthquake sources. The methodology is based on the established monte carlo approach to probabilistic seismic hazard assessment (PSHA) and has been adapted to tsunami. We account for sources of epistemic and aleatory uncertainty in the analysis through the use of logic trees and sampling probability density functions. For short return periods (100 years) the highest tsunami hazard is the west coast of Sumatra, south coast of Java and the north coast of Papua. For longer return periods (500-2500 years), the tsunami hazard is highest along the Sunda Arc, reflecting the larger maximum magnitudes. The annual probability of experiencing a tsunami with a height of > 0.5 m at the coast is greater than 10% for Sumatra, Java, the Sunda islands (Bali, Lombok, Flores, Sumba) and north Papua. The annual probability of experiencing a tsunami with a height of > 3.0 m, which would cause significant inundation and fatalities, is 1-10% in Sumatra, Java, Bali, Lombok and north Papua, and 0.1-1% for north Sulawesi, Seram and Flores. The results of this national-scale hazard assessment provide evidence for disaster managers to prioritise regions for risk mitigation activities and/or more detailed hazard or risk assessment.

A~probabilistic tsunami hazard assessment for Indonesia

Science.gov (United States)

Horspool, N.; Pranantyo, I.; Griffin, J.; Latief, H.; Natawidjaja, D. H.; Kongko, W.; Cipta, A.; Bustaman, B.; Anugrah, S. D.; Thio, H. K.

2014-05-01

Probabilistic hazard assessments are a fundamental tool for assessing the threats posed by hazards to communities and are important for underpinning evidence based decision making on risk mitigation activities. Indonesia has been the focus of intense tsunami risk mitigation efforts following the 2004 Indian Ocean Tsunami, but this has been largely concentrated on the Sunda Arc, with little attention to other tsunami prone areas of the country such as eastern Indonesia. We present the first nationally consistent Probabilistic Tsunami Hazard Assessment (PTHA) for Indonesia. This assessment produces time independent forecasts of tsunami hazard at the coast from tsunami generated by local, regional and distant earthquake sources. The methodology is based on the established monte-carlo approach to probabilistic seismic hazard assessment (PSHA) and has been adapted to tsunami. We account for sources of epistemic and aleatory uncertainty in the analysis through the use of logic trees and through sampling probability density functions. For short return periods (100 years) the highest tsunami hazard is the west coast of Sumatra, south coast of Java and the north coast of Papua. For longer return periods (500-2500 years), the tsunami hazard is highest along the Sunda Arc, reflecting larger maximum magnitudes along the Sunda Arc. The annual probability of experiencing a tsunami with a height at the coast of > 0.5 m is greater than 10% for Sumatra, Java, the Sunda Islands (Bali, Lombok, Flores, Sumba) and north Papua. The annual probability of experiencing a tsunami with a height of >3.0 m, which would cause significant inundation and fatalities, is 1-10% in Sumatra, Java, Bali, Lombok and north Papua, and 0.1-1% for north Sulawesi, Seram and Flores. The results of this national scale hazard assessment provide evidence for disaster managers to prioritise regions for risk mitigation activities and/or more detailed hazard or risk assessment.

14 CFR 221.200 - Content and explanation of abbreviations, reference marks and symbols.

Science.gov (United States)

2010-01-01

..., reference marks and symbols. 221.200 Section 221.200 Aeronautics and Space OFFICE OF THE SECRETARY... § 221.200 Content and explanation of abbreviations, reference marks and symbols. (a) Content. The format..., reference marks and symbols. Abbreviations, reference marks and symbols which are used in the tariff shall...

A proposal for performing software safety hazard analysis

International Nuclear Information System (INIS)

Lawrence, J.D.; Gallagher, J.M.

1997-01-01

Techniques for analyzing the safety and reliability of analog-based electronic protection systems that serve to mitigate hazards in process control systems have been developed over many years, and are reasonably understood. An example is the protection system in a nuclear power plant. The extension of these techniques to systems which include digital computers is not well developed, and there is little consensus among software engineering experts and safety experts on how to analyze such systems. One possible technique is to extend hazard analysis to include digital computer-based systems. Software is frequently overlooked during system hazard analyses, but this is unacceptable when the software is in control of a potentially hazardous operation. In such cases, hazard analysis should be extended to fully cover the software. A method for performing software hazard analysis is proposed in this paper. The method concentrates on finding hazards during the early stages of the software life cycle, using an extension of HAZOP

The theological significance of the Isaiah citation in Mark 4:12 ...

African Journals Online (AJOL)

The well-known passage Mark 4:1–34 is no stranger to New Testament scientific scrutiny, not to even mention the hotly debated phrases in Mark 4:10–12. To avoid repetition, the aim with this article is to determine the extent of the impact the Isaiah 6:9–10 citation in Mark 4:12 might have had on the interpretation and ...

Agent-based simulation for human-induced hazard analysis.

Science.gov (United States)

Bulleit, William M; Drewek, Matthew W

2011-02-01

Terrorism could be treated as a hazard for design purposes. For instance, the terrorist hazard could be analyzed in a manner similar to the way that seismic hazard is handled. No matter how terrorism is dealt with in the design of systems, the need for predictions of the frequency and magnitude of the hazard will be required. And, if the human-induced hazard is to be designed for in a manner analogous to natural hazards, then the predictions should be probabilistic in nature. The model described in this article is a prototype model that used agent-based modeling (ABM) to analyze terrorist attacks. The basic approach in this article of using ABM to model human-induced hazards has been preliminarily validated in the sense that the attack magnitudes seem to be power-law distributed and attacks occur mostly in regions where high levels of wealth pass through, such as transit routes and markets. The model developed in this study indicates that ABM is a viable approach to modeling socioeconomic-based infrastructure systems for engineering design to deal with human-induced hazards. © 2010 Society for Risk Analysis.

Environmentally sound management of hazardous waste and hazardous recyclable materials

International Nuclear Information System (INIS)

Smyth, T.

2002-01-01

Environmentally sound management or ESM has been defined under the Basel Convention as 'taking all practicable steps to ensure that hazardous wastes and other wastes are managed in a manner which will protect human health and the environment against the adverse effects which may result from such wastes'. An initiative is underway to develop and implement a Canadian Environmentally Sound Management (ESM) regime for both hazardous wastes and hazardous recyclable materials. This ESM regime aims to assure equivalent minimum environmental protection across Canada while respecting regional differences. Cooperation and coordination between the federal government, provinces and territories is essential to the development and implementation of ESM systems since waste management is a shared jurisdiction in Canada. Federally, CEPA 1999 provides an opportunity to improve Environment Canada's ability to ensure that all exports and imports are managed in an environmentally sound manner. CEPA 1999 enabled Environment Canada to establish criteria for environmentally sound management (ESM) that can be applied by importers and exporters in seeking to ensure that wastes and recyclable materials they import or export will be treated in an environmentally sound manner. The ESM regime would include the development of ESM principles, criteria and guidelines relevant to Canada and a procedure for evaluating ESM. It would be developed in full consultation with stakeholders. The timeline for the development and implementation of the ESM regime is anticipated by about 2006. (author)

Hazardous factories: Nigerian evidence.

Science.gov (United States)

Oloyede, Olajide

2005-06-01

The past 15 years have seen an increasing governmental and corporate concern for the environment worldwide. For governments, information about the environmental performance of the industrial sector is required to inform macro-level decisions about environmental targets such as those required to meet UN directives. However, in many African, Asian, and Latin American countries, researching and reporting company environmental performance is limited. This article serves as a contribution to filling the gap by presenting evidence of physical and chemical risk in Nigerian factories. One hundred and three factories with a total of 5,021 workers were studied. One hundred and twenty physical and chemical hazards were identified and the result shows a high number of workers exposed to such hazards. The study also reveals that workers' awareness level of chemical hazards was high. Yet the danger was perceived in behavioral terms, especially by manufacturing firms, which tend to see environmental investment in an increasingly global economy as detrimental to profitability.

Multi scenario seismic hazard assessment for Egypt

Science.gov (United States)

Mostafa, Shaimaa Ismail; Abd el-aal, Abd el-aziz Khairy; El-Eraki, Mohamed Ahmed

2018-05-01

Egypt is located in the northeastern corner of Africa within a sensitive seismotectonic location. Earthquakes are concentrated along the active tectonic boundaries of African, Eurasian, and Arabian plates. The study area is characterized by northward increasing sediment thickness leading to more damage to structures in the north due to multiple reflections of seismic waves. Unfortunately, man-made constructions in Egypt were not designed to resist earthquake ground motions. So, it is important to evaluate the seismic hazard to reduce social and economic losses and preserve lives. The probabilistic seismic hazard assessment is used to evaluate the hazard using alternative seismotectonic models within a logic tree framework. Alternate seismotectonic models, magnitude-frequency relations, and various indigenous attenuation relationships were amended within a logic tree formulation to compute and develop the regional exposure on a set of hazard maps. Hazard contour maps are constructed for peak ground acceleration as well as 0.1-, 0.2-, 0.5-, 1-, and 2-s spectral periods for 100 and 475 years return periods for ground motion on rock. The results illustrate that Egypt is characterized by very low to high seismic activity grading from the west to the eastern part of the country. The uniform hazard spectra are estimated at some important cities distributed allover Egypt. The deaggregation of seismic hazard is estimated at some cities to identify the scenario events that contribute to a selected seismic hazard level. The results of this study can be used in seismic microzonation, risk mitigation, and earthquake engineering purposes.

Application of the Coastal Hazard Wheel methodology for coastal multi-hazard assessment and management in the state of Djibouti

DEFF Research Database (Denmark)

Appelquist, Lars Rosendahl; Balstrøm, Thomas

2014-01-01

coastal classification system that incorporates the main static and dynamic parameters determining the characteristics of a coastal environment. The methodology provides information on the hazards of ecosystem disruption, gradual inundation, salt water intrusion, erosion and flooding and can be used...... to support management decisions at local, regional and national level, in areas with limited access to geophysical data. The assessment for Djibouti applies a geographic information system (GIS) to develop a range of national hazard maps along with relevant hazard statistics and is showcasing the procedure......This paper presents the application of a new methodology for coastal multi-hazard assessment and management in a changing global climate on the state of Djibouti. The methodology termed the Coastal Hazard Wheel (CHW) is developed for worldwide application and is based on a specially designed...

Rockfall Hazard Process Assessment : [Project Summary

Science.gov (United States)

2017-10-01

The Montana Department of Transportation (MDT) implemented its Rockfall Hazard Rating System (RHRS) between 2003 and 2005, obtaining information on the state's rock slopes and their associated hazards. The RHRS data facilitated decision-making in an ...

Better marking means cheaper pruning.

Science.gov (United States)

Kenneth R. Eversole

1953-01-01

Careful selection of trees to be pruned can make the difference between profit and loss on the pruning investment, especially in stands where no thinning is contemplated. Expert marking is required to make sure that the pruned trees will grow rapidly. The most important variable influencing the cost of clear wood produced by pruning is growth rate. For example, at 3...

Full-scale mark II CRT program data report, (5)

International Nuclear Information System (INIS)

Kukita, Yutaka; Namatame, Ken; Yamamoto, Nobuo; Takeshita, Isao; Shiba, Masayoshi

1980-03-01

The Full-Scale Mark II CRT (Containment Response Test) Program was initiated in 1977 to provide a data base for evaluation of the LOCA hydrodynamic loads for the Mark II pressure suppression system. The test facility is 1/18 in volume and has a wetwell which is a fullscale replica of one 20 0 -sector of that of a reference Mark II. This report documents test data obtained from TEST 2101, which is a medium size (74 mm) water break test performed on April 27, 1979. TEST 2101 was designed to roughly approximate an intermediate break accident in which so-called chugging phenomenon associated with low-flux steam condensation is anticipated to continue for a longer duration than in a large break accident. (author)

Mark I containment, short term program. Safety evaluation report

International Nuclear Information System (INIS)

1977-12-01

Presented is a Safety Evaluation Report (SER) prepared by the Office of Nuclear Reactor Regulation addressing the Short Term Program (STP) reassessment of the containment systems of operating Boiler Water Reactor (BWR) facilities with the Mark I containment system design. The information presented in this SER establishes the basis for the NRC staff's conclusion that licensed Mark I BWR facilities can continue to operate safely, without undue risk to the health and safety of the public, during an interim period of approximately two years while a methodical, comprehensive Long Term Program (LTP) is conducted. This SER also provides one of the basic foundations for the NRC staff review of the Mark I containment systems for facilities not yet licensed for operation

Hazardous metals in yellow items used in RCAs

International Nuclear Information System (INIS)

Brown, K.F.; Rankin, W.N.

1992-01-01

Yellow items used in Radiologically Controlled Areas (RCAs) that could contain hazardous metals were identified. X-ray fluorescence analyses indicated that thirty of the fifty-two items do contain hazardous metals. It is important to minimize the hazardous metals put into the wastes. The authors recommend that the specifications for all yellow items stocked in Stores be changed to specify that they contain no hazardous metals

Collateral benefits and hidden hazards of soil arsenic during abatement assessment of residential lead hazards

International Nuclear Information System (INIS)

Elless, M.P.; Ferguson, B.W.; Bray, C.A.; Patch, S.; Mielke, H.; Blaylock, M.J.

2008-01-01

Abatement of soil-lead hazards may also reduce human exposure to other soil toxins, thereby achieving significant collateral benefits that are not accounted for today. This proposition was tested with the specific case of soil-arsenic, where 1726 residential soil samples were collected and analyzed for lead and arsenic. The study found that these two toxins coexisted in most samples, but their concentrations were weakly correlated, reflecting the differing sources for each toxin. Collateral benefits of 9% would be achieved during abatement of the lead-contaminated soils having elevated arsenic concentrations. However, a hidden hazard of 16% was observed by overlooking elevated arsenic concentrations in soils having lead concentrations not requiring abatement. This study recommends that soil samples collected under HUD programs should be collected from areas of lead and arsenic deposition and tested for arsenic as well as lead, and that soil abatement decisions consider soil-arsenic as well as soil-lead guidelines. - Coexistence of arsenic at elevated concentrations with lead in residential soils undergoing lead hazard assessment is often overlooked, providing either collateral benefits or hidden hazards

Ceremony marking Einstein Year

CERN Multimedia

2005-01-01

Sunday 13th November at 10:00amat Geneva's St. Peter's Cathedral To mark Einstein Year and the importance of the intercultural dialogue of which it forms a part, a religious service will take place on Sunday 13 November at 10 a.m. in St. Peter's Cathedral, to which CERN members and colleagues are warmly welcomed. Pastor Henry Babel, senior minister at the Cathedral, will speak on the theme: 'God in Einstein's Universe'. Diether Blechschmidt will convey a message on behalf of the scientific community.

Flood Hazard Mapping by Applying Fuzzy TOPSIS Method

Science.gov (United States)

Han, K. Y.; Lee, J. Y.; Keum, H.; Kim, B. J.; Kim, T. H.

2017-12-01

There are lots of technical methods to integrate various factors for flood hazard mapping. The purpose of this study is to suggest the methodology of integrated flood hazard mapping using MCDM(Multi Criteria Decision Making). MCDM problems involve a set of alternatives that are evaluated on the basis of conflicting and incommensurate criteria. In this study, to apply MCDM to assessing flood risk, maximum flood depth, maximum velocity, and maximum travel time are considered as criterion, and each applied elements are considered as alternatives. The scheme to find the efficient alternative closest to a ideal value is appropriate way to assess flood risk of a lot of element units(alternatives) based on various flood indices. Therefore, TOPSIS which is most commonly used MCDM scheme is adopted to create flood hazard map. The indices for flood hazard mapping(maximum flood depth, maximum velocity, and maximum travel time) have uncertainty concerning simulation results due to various values according to flood scenario and topographical condition. These kind of ambiguity of indices can cause uncertainty of flood hazard map. To consider ambiguity and uncertainty of criterion, fuzzy logic is introduced which is able to handle ambiguous expression. In this paper, we made Flood Hazard Map according to levee breach overflow using the Fuzzy TOPSIS Technique. We confirmed the areas where the highest grade of hazard was recorded through the drawn-up integrated flood hazard map, and then produced flood hazard map can be compared them with those indicated in the existing flood risk maps. Also, we expect that if we can apply the flood hazard map methodology suggested in this paper even to manufacturing the current flood risk maps, we will be able to make a new flood hazard map to even consider the priorities for hazard areas, including more varied and important information than ever before. Keywords : Flood hazard map; levee break analysis; 2D analysis; MCDM; Fuzzy TOPSIS

The Volcanic Hazards Assessment Support System for the Online Hazard Assessment and Risk Mitigation of Quaternary Volcanoes in the World

Directory of Open Access Journals (Sweden)

Shinji Takarada

2017-12-01

Full Text Available Volcanic hazards assessment tools are essential for risk mitigation of volcanic activities. A number of offline volcanic hazard assessment tools have been provided, but in most cases, they require relatively complex installation procedure and usage. This situation causes limited usage of volcanic hazard assessment tools among volcanologists and volcanic hazards communities. In addition, volcanic eruption chronology and detailed database of each volcano in the world are essential key information for volcanic hazard assessment, but most of them are isolated and not connected to and with each other. The Volcanic Hazard Assessment Support System aims to implement a user-friendly, WebGIS-based, open-access online system for potential hazards assessment and risk-mitigation of Quaternary volcanoes in the world. The users can get up-to-date information such as eruption chronology and geophysical monitoring data of a specific volcano using the direct link system to major volcano databases on the system. Currently, the system provides 3 simple, powerful and notable deterministic modeling simulation codes of volcanic processes, such as Energy Cone, Titan2D and Tephra2. The system provides deterministic tools because probabilistic assessment tools are normally much more computationally demanding. By using the volcano hazard assessment system, the area that would be affected by volcanic eruptions in any location near the volcano can be estimated using numerical simulations. The system is being implemented using the ASTER Global DEM covering 2790 Quaternary volcanoes in the world. The system can be used to evaluate volcanic hazards and move this toward risk-potential by overlaying the estimated distribution of volcanic gravity flows or tephra falls on major roads, houses and evacuation areas using the GIS-enabled systems. The system is developed for all users in the world who need volcanic hazards assessment tools.

The interplay of attention economics and computer-aided detection marks in screening mammography

Science.gov (United States)

Schwartz, Tayler M.; Sridharan, Radhika; Wei, Wei; Lukyanchenko, Olga; Geiser, William; Whitman, Gary J.; Haygood, Tamara Miner

2016-03-01

Introduction: According to attention economists, overabundant information leads to decreased attention for individual pieces of information. Computer-aided detection (CAD) alerts radiologists to findings potentially associated with breast cancer but is notorious for creating an abundance of false-positive marks. We suspected that increased CAD marks do not lengthen mammogram interpretation time, as radiologists will selectively disregard these marks when present in larger numbers. We explore the relevance of attention economics in mammography by examining how the number of CAD marks affects interpretation time. Methods: We performed a retrospective review of bilateral digital screening mammograms obtained between January 1, 2011 and February 28, 2014, using only weekend interpretations to decrease distractions and the likelihood of trainee participation. We stratified data according to reader and used ANOVA to assess the relationship between number of CAD marks and interpretation time. Results: Ten radiologists, with median experience after residency of 12.5 years (range 6 to 24,) interpreted 1849 mammograms. When accounting for number of images, Breast Imaging Reporting and Data System category, and breast density, increasing numbers of CAD marks was correlated with longer interpretation time only for the three radiologists with the fewest years of experience (median 7 years.) Conclusion: For the 7 most experienced readers, increasing CAD marks did not lengthen interpretation time. We surmise that as CAD marks increase, the attention given to individual marks decreases. Experienced radiologists may rapidly dismiss larger numbers of CAD marks as false-positive, having learned that devoting extra attention to such marks does not improve clinical detection.

Bench mark spectra for high-energy neutron dosimetry

International Nuclear Information System (INIS)

Dierckx, R.

1986-01-01

To monitor radiation damage experiments, activation detectors are commonly used. The precision of the results obtained by the multiple foil analysis is largely increased by the intercalibration in bench-mark spectra. This technique is already used in dosimetry measurements for fission reactors. To produce neutron spectra similar to fusion reactor and high-energy high-intensity neutron sources (d-Li or spallation), accelerators can be used. Some possible solutions as p-Be and d-D 2 O neutron sources, useful as bench-mark spectra are described. (author)

Final Report: Seismic Hazard Assessment at the PGDP

Energy Technology Data Exchange (ETDEWEB)

Wang, Zhinmeng [KY Geological Survey, Univ of KY

2007-06-01

Selecting a level of seismic hazard at the Paducah Gaseous Diffusion Plant for policy considerations and engineering design is not an easy task because it not only depends on seismic hazard, but also on seismic risk and other related environmental, social, and economic issues. Seismic hazard is the main focus. There is no question that there are seismic hazards at the Paducah Gaseous Diffusion Plant because of its proximity to several known seismic zones, particularly the New Madrid Seismic Zone. The issues in estimating seismic hazard are (1) the methods being used and (2) difficulty in characterizing the uncertainties of seismic sources, earthquake occurrence frequencies, and ground-motion attenuation relationships. This report summarizes how input data were derived, which methodologies were used, and what the hazard estimates at the Paducah Gaseous Diffusion Plant are.

Increasing resiliency to natural hazards - A strategic plan for the Multi-Hazards Demonstration Project in Southern California

Science.gov (United States)

Jones, Lucy; Bernknopf, Richard; Cannon, Susan; Cox, Dale A.; Gaydos, Len; Keeley, Jon; Kohler, Monica; Lee, Homa; Ponti, Daniel; Ross, Stephanie L.; Schwarzbach, Steven; Shulters, Michael; Ward, A. Wesley; Wein, Anne

2007-01-01

The U.S. Geological Survey (USGS) is initiating a new project designed to improve resiliency to natural hazards in southern California through the application of science to community decision making and emergency response. The Multi-Hazards Demonstration Project will assist the region’s communities to reduce their risk from natural hazards by directing new and existing research towards the community’s needs, improving monitoring technology, producing innovative products, and improving dissemination of the results. The natural hazards to be investigated in this project include coastal erosion, earthquakes, floods, landslides, tsunamis, and wildfires.Americans are more at risk from natural hazards now than at any other time in our Nation’s history. Southern California, in particular, has one of the Nation’s highest potentials for extreme catastrophic losses due to natural hazards, with estimates of expected losses exceeding $3 billion per year. These losses can only be reduced through the decisions of the southern California community itself. To be effective, these decisions must be guided by the best information about hazards, risk, and the cost-effectiveness of mitigation technologies. The USGS will work with collaborators to set the direction of the research and to create multi-hazard risk frameworks where communities can apply the results of scientific research to their decision-making processes. Partners include state, county, city, and public-lands government agencies, public and private utilities, companies with a significant impact and presence in southern California, academic researchers, the Federal Emergency Management Agency (FEMA), National Oceanic and Atmospheric Administration (NOAA), and local emergency response agencies.Prior to the writing of this strategic plan document, three strategic planning workshops were held in February and March 2006 at the USGS office in Pasadena to explore potential relationships. The goal of these planning

Hazardous materials management and compliance training

International Nuclear Information System (INIS)

Dalton, T.F.

1991-01-01

OSHA training for hazardous waste site workers is required by the Superfund Amendments and Reauthorization Act of 1986 (SARA). In December 1986, a series of regulations was promulgated by OSHA on an interim basis calling for the training of workers engaged in hazardous waste operations. Subsequent to these interim regulations, final rules were promulgated and these final rules on hazardous waste operations and emergency response became effective on March 6, 1990. OSHA has conducted hearings on the accreditation of training programs. OSHA would like to follow the accreditation process under the AHERA regulations for asbestos, in which the model plan for accreditation of asbestos abatement training was included in Section 206 of Title 11 of the Toxic Substance Control Act (TSCA). OSHA proposed on January 26, 1990, to perform the accreditation of training programs for hazardous waste operations and that proposal suggested that they follow the model plan similar to the one used for AHERA. They did not propose to accredited training programs for workers engaged in emergency response. These new regulations pose a significant problem to the various contractors and emergency responders who deal with hazardous materials spill response, cleanup and site remediation since these programs have expanded so quickly that many people are not familiar with what particular segment of the training they are required to have and whether or not programs that have yet to be accredited are satisfactory for this type of training. Title III of SARA stipulates a training program for first responders which includes local emergency response organizations such as firemen and policemen. The purpose of this paper is to discuss the needs of workers at hazardous waste site remediation projects and workers who are dealing with hazardous substances, spill response and cleanup

Experimental investigations on fiber laser color marking of steels

Energy Technology Data Exchange (ETDEWEB)

Amara, E.H., E-mail: amara@cdta.dz; Haïd, F.; Noukaz, A.

2015-10-01

Highlights: • We develop an experimental approach with the aim to bring a contribution to the comprehension of the occurring phenomena during laser color marking of steels. • We have used a home-made marking device composed of a pulsed fiber laser and galvanometric mirrors. • Both commercial and elaborated in laboratory steels have been used as samples. • The experiments have been performed for different laser beam operating parameters, under normal atmospheric conditions. • The treated samples were analyzed either by optical and scanning electronic microscopy, as well as by energy dispersion spectroscopy. - Abstract: We develop an experimental approach with the aim to bring a contribution to the comprehension of the occurring phenomena during laser color marking of steels. A home-made marking device using a pulsed fiber laser has been used to treat steel samples under different laser beam operating parameters, for different compositions of the processed steel, and at normal atmospheric conditions. The treated samples were analyzed either by optical and scanning electronic microscopy, as well as by energy dispersion spectroscopy. The results show the influence of the operating parameters on the obtained colors.

Experimental investigations on fiber laser color marking of steels

International Nuclear Information System (INIS)

Amara, E.H.; Haïd, F.; Noukaz, A.

2015-01-01

Highlights: • We develop an experimental approach with the aim to bring a contribution to the comprehension of the occurring phenomena during laser color marking of steels. • We have used a home-made marking device composed of a pulsed fiber laser and galvanometric mirrors. • Both commercial and elaborated in laboratory steels have been used as samples. • The experiments have been performed for different laser beam operating parameters, under normal atmospheric conditions. • The treated samples were analyzed either by optical and scanning electronic microscopy, as well as by energy dispersion spectroscopy. - Abstract: We develop an experimental approach with the aim to bring a contribution to the comprehension of the occurring phenomena during laser color marking of steels. A home-made marking device using a pulsed fiber laser has been used to treat steel samples under different laser beam operating parameters, for different compositions of the processed steel, and at normal atmospheric conditions. The treated samples were analyzed either by optical and scanning electronic microscopy, as well as by energy dispersion spectroscopy. The results show the influence of the operating parameters on the obtained colors

Tsunami hazard

Energy Technology Data Exchange (ETDEWEB)

NONE

2013-08-15

Tohoku Earthquake Tsunami on 11 March, 2011 has led the Fukushima Daiichi nuclear power plant to a serious accident, which highlighted a variety of technical issues such as a very low design tsunami height and insufficient preparations in case a tsunami exceeding the design tsunami height. Lessons such as to take measures to be able to maintain the important safety features of the facility for tsunamis exceeding design height and to implement risk management utilizing Probabilistic Safety Assessment are shown. In order to implement the safety assessment on nuclear power plants across Japan accordingly to the back-fit rule, Nuclear Regulatory Commission will promulgate/execute the New Safety Design Criteria in July 2013. JNES has positioned the 'enhancement of probabilistic tsunami hazard assessment' as highest priority issue and implemented in order to support technically the Nuclear Regulatory Authority in formulating the new Safety Design Criteria. Findings of the research had reflected in the 'Technical Review Guidelines for Assessing Design Tsunami Height based on tsunami hazards'. (author)

Geologic bench marks by terrestrial photography

Science.gov (United States)

Malde, Harold E.

1973-01-01

A photograph made with a level camera, if taken at a known height above a permanent mark on the ground, can be later repeated with exactness for measurement of changes in terrain. Such a photograph is one of several means for establishing a geologic bench mark and is especially useful for monitoring the subtle qualities of a landscape that are otherwise hard to map and describe, including the effects of man's use. Moreover, the geometry of such a photograph provides the same angular measurements between objects as can be made with a transit. A measurement of distance on a single photograph, however, requires control points. These can be surveyed at any convenient time, not necessarily when the initial photograph is made. Distances can also be determined by simple stereophotography from a base line of suitable length.

Landslides Hazard Assessment Using Different Approaches

Directory of Open Access Journals (Sweden)

Coman Cristina

2017-06-01

Full Text Available Romania represents one of Europe’s countries with high landslides occurrence frequency. Landslide hazard maps are designed by considering the interaction of several factors which, by their joint action may affect the equilibrium state of the natural slopes. The aim of this paper is landslides hazard assessment using the methodology provided by the Romanian national legislation and a very largely used statistical method. The final results of these two analyses are quantitative or semi-quantitative landslides hazard maps, created in geographic information system environment. The data base used for this purpose includes: geological and hydrogeological data, digital terrain model, hydrological data, land use, seismic action, anthropic action and an inventory of active landslides. The GIS landslides hazard models were built for the geographical area of the Iasi city, located in the north-east side of Romania.