Hazards assessment for the Waste Experimental Reduction Facility

International Nuclear Information System (INIS)

Calley, M.B.; Jones, J.L. Jr.

1994-01-01

This report documents the hazards assessment for the Waste Experimental Reduction Facility (WERF) located at the Idaho National Engineering Laboratory, which is operated by EG ampersand G Idaho, Inc., for the US Department of Energy (DOE). The hazards assessment was performed to ensure that this facility complies with DOE and company requirements pertaining to emergency planning and preparedness for operational emergencies. DOE Order 5500.3A requires that a facility-specific hazards assessment be performed to provide the technical basis for facility emergency planning efforts. This hazards assessment was conducted in accordance with DOE Headquarters and DOE Idaho Operations Office (DOE-ID) guidance to comply with DOE Order 5500.3A. The hazards assessment identifies and analyzes hazards that are significant enough to warrant consideration in a facility's operational emergency management program. This hazards assessment describes the WERF, the area surrounding WERF, associated buildings and structures at WERF, and the processes performed at WERF. All radiological and nonradiological hazardous materials stored, used, or produced at WERF were identified and screened. Even though the screening process indicated that the hazardous materials could be screened from further analysis because the inventory of radiological and nonradiological hazardous materials were below the screening thresholds specified by DOE and DOE-ID guidance for DOE Order 5500.3A, the nonradiological hazardous materials were analyzed further because it was felt that the nonradiological hazardous material screening thresholds were too high

Hazards assessment for the Waste Experimental Reduction Facility

Energy Technology Data Exchange (ETDEWEB)

Calley, M.B.; Jones, J.L. Jr.

1994-09-19

This report documents the hazards assessment for the Waste Experimental Reduction Facility (WERF) located at the Idaho National Engineering Laboratory, which is operated by EG&G Idaho, Inc., for the US Department of Energy (DOE). The hazards assessment was performed to ensure that this facility complies with DOE and company requirements pertaining to emergency planning and preparedness for operational emergencies. DOE Order 5500.3A requires that a facility-specific hazards assessment be performed to provide the technical basis for facility emergency planning efforts. This hazards assessment was conducted in accordance with DOE Headquarters and DOE Idaho Operations Office (DOE-ID) guidance to comply with DOE Order 5500.3A. The hazards assessment identifies and analyzes hazards that are significant enough to warrant consideration in a facility`s operational emergency management program. This hazards assessment describes the WERF, the area surrounding WERF, associated buildings and structures at WERF, and the processes performed at WERF. All radiological and nonradiological hazardous materials stored, used, or produced at WERF were identified and screened. Even though the screening process indicated that the hazardous materials could be screened from further analysis because the inventory of radiological and nonradiological hazardous materials were below the screening thresholds specified by DOE and DOE-ID guidance for DOE Order 5500.3A, the nonradiological hazardous materials were analyzed further because it was felt that the nonradiological hazardous material screening thresholds were too high.

The Volcanic Hazards Assessment Support System for the Online Hazard Assessment and Risk Mitigation of Quaternary Volcanoes in the World

Directory of Open Access Journals (Sweden)

Shinji Takarada

2017-12-01

Full Text Available Volcanic hazards assessment tools are essential for risk mitigation of volcanic activities. A number of offline volcanic hazard assessment tools have been provided, but in most cases, they require relatively complex installation procedure and usage. This situation causes limited usage of volcanic hazard assessment tools among volcanologists and volcanic hazards communities. In addition, volcanic eruption chronology and detailed database of each volcano in the world are essential key information for volcanic hazard assessment, but most of them are isolated and not connected to and with each other. The Volcanic Hazard Assessment Support System aims to implement a user-friendly, WebGIS-based, open-access online system for potential hazards assessment and risk-mitigation of Quaternary volcanoes in the world. The users can get up-to-date information such as eruption chronology and geophysical monitoring data of a specific volcano using the direct link system to major volcano databases on the system. Currently, the system provides 3 simple, powerful and notable deterministic modeling simulation codes of volcanic processes, such as Energy Cone, Titan2D and Tephra2. The system provides deterministic tools because probabilistic assessment tools are normally much more computationally demanding. By using the volcano hazard assessment system, the area that would be affected by volcanic eruptions in any location near the volcano can be estimated using numerical simulations. The system is being implemented using the ASTER Global DEM covering 2790 Quaternary volcanoes in the world. The system can be used to evaluate volcanic hazards and move this toward risk-potential by overlaying the estimated distribution of volcanic gravity flows or tephra falls on major roads, houses and evacuation areas using the GIS-enabled systems. The system is developed for all users in the world who need volcanic hazards assessment tools.

Tank farms hazards assessment

International Nuclear Information System (INIS)

Broz, R.E.

1994-01-01

Hanford contractors are writing new facility specific emergency procedures in response to new and revised US Department of Energy (DOE) Orders on emergency preparedness. Emergency procedures are required for each Hanford facility that has the potential to exceed the criteria for the lowest level emergency, an Alert. The set includes: (1) a facility specific procedure on Recognition and Classification of Emergencies, (2) area procedures on Initial Emergency Response and, (3) an area procedure on Protective Action Guidance. The first steps in developing these procedures are to identify the hazards at each facility, identify the conditions that could release the hazardous material, and calculate the consequences of the releases. These steps are called a Hazards Assessment. The final product is a document that is similar in some respects to a Safety Analysis Report (SAR). The document could br produced in a month for a simple facility but could take much longer for a complex facility. Hanford has both types of facilities. A strategy has been adopted to permit completion of the first version of the new emergency procedures before all the facility hazards Assessments are complete. The procedures will initially be based on input from a task group for each facility. This strategy will but improved emergency procedures in place sooner and therefore enhance Hanford emergency preparedness. The purpose of this document is to summarize the applicable information contained within the Waste Tank Facility ''Interim Safety Basis Document, WHC-SD-WM-ISB-001'' as a resource, since the SARs covering Waste Tank Operations are not current in all cases. This hazards assessment serves to collect, organize, document and present the information utilized during the determination process

Risk assessments for energy systems and role of preliminary degree-of-hazard evaluations

International Nuclear Information System (INIS)

Habegger, L.J.; Fingleton, D.J.

1985-11-01

The appropriate approach to risk or hazard assessment can vary considerably, depending on various factors, including the intended application of the results and the time other resources available to conduct the assessment. This paper illustrates three types of interrelated assessments. Although they can be mutually supportive, they have fundamentally different objectives, which require major differences in approach. The example of the overall risk assessment of alternative major energy technologies illustrates the compilation of a wide range of available risk data applicable to these systems. However, major uncertainties exist in the assessments, and public perception of their importance could play an important role in final system evaluations. A more narrowly defined risk assessment, often focusing on an individual component of a larger system, is the most commonly used approach in regulatory applications. The narrow scope allows in-depth analysis of risks and associated uncertainties, but it may also contribute to a loss of perspective on the magnitude of the assessed risk relative to that of the unassessed risks. In some applications, it is useful to conduct semiquantitative degree-of-hazard evaluations as a means of setting priorities for detailed risk assessment. The MAHAS procedure described in this paper provides a means of rapidly ranking relative hazards from various sources using easily accessible data. However, these rankings should not be used as definitive input for selecting technology alternatives or developing regulations. 25 refs., 6 tabs

GEOSPATIAL DATA INTEGRATION FOR ASSESSING LANDSLIDE HAZARD ON ENGINEERED SLOPES

Directory of Open Access Journals (Sweden)

P. E. Miller

2012-07-01

Full Text Available Road and rail networks are essential components of national infrastructures, underpinning the economy, and facilitating the mobility of goods and the human workforce. Earthwork slopes such as cuttings and embankments are primary components, and their reliability is of fundamental importance. However, instability and failure can occur, through processes such as landslides. Monitoring the condition of earthworks is a costly and continuous process for network operators, and currently, geospatial data is largely underutilised. The research presented here addresses this by combining airborne laser scanning and multispectral aerial imagery to develop a methodology for assessing landslide hazard. This is based on the extraction of key slope stability variables from the remotely sensed data. The methodology is implemented through numerical modelling, which is parameterised with the slope stability information, simulated climate conditions, and geotechnical properties. This allows determination of slope stability (expressed through the factor of safety for a range of simulated scenarios. Regression analysis is then performed in order to develop a functional model relating slope stability to the input variables. The remotely sensed raster datasets are robustly re-sampled to two-dimensional cross-sections to facilitate meaningful interpretation of slope behaviour and mapping of landslide hazard. Results are stored in a geodatabase for spatial analysis within a GIS environment. For a test site located in England, UK, results have shown the utility of the approach in deriving practical hazard assessment information. Outcomes were compared to the network operator’s hazard grading data, and show general agreement. The utility of the slope information was also assessed with respect to auto-population of slope geometry, and found to deliver significant improvements over the network operator’s existing field-based approaches.

PUREX facility hazards assessment

International Nuclear Information System (INIS)

Sutton, L.N.

1994-01-01

This report documents the hazards assessment for the Plutonium Uranium Extraction Plant (PUREX) located on the US Department of Energy (DOE) Hanford Site. Operation of PUREX is the responsibility of Westinghouse Hanford Company (WHC). This hazards assessment was conducted to provide the emergency planning technical basis for PUREX. DOE Order 5500.3A requires an emergency planning hazards assessment for each facility that has the potential to reach or exceed the lowest level emergency classification. In October of 1990, WHC was directed to place PUREX in standby. In December of 1992 the DOE Assistant Secretary for Environmental Restoration and Waste Management authorized the termination of PUREX and directed DOE-RL to proceed with shutdown planning and terminal clean out activities. Prior to this action, its mission was to reprocess irradiated fuels for the recovery of uranium and plutonium. The present mission is to establish a passively safe and environmentally secure configuration at the PUREX facility and to preserve that condition for 10 years. The ten year time frame represents the typical duration expended to define, authorize and initiate follow-on decommissioning and decontamination activities

Onsite transportation hazards assessment

International Nuclear Information System (INIS)

Burnside, M.E.

1998-01-01

This report documents the emergency preparedness Hazards Assessment for the onsite transportation of hazardous material at the Hanford Site. The assessment is required by US Department of Energy (DOE) Order 5500.3A and provides the technical basis for the emergency classification and response procedures. A distinction is made between onsite for the purpose of emergency preparedness and onsite for the purpose of applying US Department of Transportation (DOT) regulations. Onsite for the purpose of emergency preparedness is considered to be within the physical boundary of the entire Hanford Site. Onsite for the purpose of applying DOT regulations is north of the Wye Barricade

The Coastal Hazard Wheel system for coastal multi-hazard assessment & management in a changing climate

DEFF Research Database (Denmark)

Appelquist, Lars Rosendahl; Halsnæs, Kirsten

2015-01-01

This paper presents the complete Coastal Hazard Wheel (CHW) system, developed for multi-hazard-assessment and multi-hazard-management of coastal areas worldwide under a changing climate. The system is designed as a low-tech tool that can be used in areas with limited data availability...... screening and management. The system is developed to assess the main coastal hazards in a single process and covers the hazards of ecosystem disruption, gradual inundation, salt water intrusion, erosion and flooding. The system was initially presented in 2012 and based on a range of test......-applications and feedback from coastal experts, the system has been further refined and developed into a complete hazard management tool. This paper therefore covers the coastal classification system used by the CHW, a standardized assessment procedure for implementation of multi-hazard-assessments, technical guidance...

Uncertainty on shallow landslide hazard assessment: from field data to hazard mapping

Science.gov (United States)

Trefolini, Emanuele; Tolo, Silvia; Patelli, Eduardo; Broggi, Matteo; Disperati, Leonardo; Le Tuan, Hai

2015-04-01

Shallow landsliding that involve Hillslope Deposits (HD), the surficial soil that cover the bedrock, is an important process of erosion, transport and deposition of sediment along hillslopes. Despite Shallow landslides generally mobilize relatively small volume of material, they represent the most hazardous factor in mountain regions due to their high velocity and the common absence of warning signs. Moreover, increasing urbanization and likely climate change make shallow landslides a source of widespread risk, therefore the interest of scientific community about this process grown in the last three decades. One of the main aims of research projects involved on this topic, is to perform robust shallow landslides hazard assessment for wide areas (regional assessment), in order to support sustainable spatial planning. Currently, three main methodologies may be implemented to assess regional shallow landslides hazard: expert evaluation, probabilistic (or data mining) methods and physical models based methods. The aim of this work is evaluate the uncertainty of shallow landslides hazard assessment based on physical models taking into account spatial variables such as: geotechnical and hydrogeologic parameters as well as hillslope morphometry. To achieve this goal a wide dataset of geotechnical properties (shear strength, permeability, depth and unit weight) of HD was gathered by integrating field survey, in situ and laboratory tests. This spatial database was collected from a study area of about 350 km2 including different bedrock lithotypes and geomorphological features. The uncertainty associated to each step of the hazard assessment process (e.g. field data collection, regionalization of site specific information and numerical modelling of hillslope stability) was carefully characterized. The most appropriate probability density function (PDF) was chosen for each numerical variable and we assessed the uncertainty propagation on HD strength parameters obtained by

A methodology for physically based rockfall hazard assessment

Directory of Open Access Journals (Sweden)

G. B. Crosta

2003-01-01

Full Text Available Rockfall hazard assessment is not simple to achieve in practice and sound, physically based assessment methodologies are still missing. The mobility of rockfalls implies a more difficult hazard definition with respect to other slope instabilities with minimal runout. Rockfall hazard assessment involves complex definitions for "occurrence probability" and "intensity". This paper is an attempt to evaluate rockfall hazard using the results of 3-D numerical modelling on a topography described by a DEM. Maps portraying the maximum frequency of passages, velocity and height of blocks at each model cell, are easily combined in a GIS in order to produce physically based rockfall hazard maps. Different methods are suggested and discussed for rockfall hazard mapping at a regional and local scale both along linear features or within exposed areas. An objective approach based on three-dimensional matrixes providing both a positional "Rockfall Hazard Index" and a "Rockfall Hazard Vector" is presented. The opportunity of combining different parameters in the 3-D matrixes has been evaluated to better express the relative increase in hazard. Furthermore, the sensitivity of the hazard index with respect to the included variables and their combinations is preliminarily discussed in order to constrain as objective as possible assessment criteria.

Implementing DOE guidance for hazards assessments at Rocky Flats Plant

International Nuclear Information System (INIS)

Zimmerman, G.A.

1993-01-01

Hazards Assessments are performed for a variety of activities and facilities at Rocky Flats Plant. Prior to 1991, there was no guidance for performing Hazards Assessments. Each organization that performed Hazards Assessments used its own methodology with no attempt at standardization. In 1991, DOE published guidelines for the performance of Hazards Assessments for Emergency Planning (DOE-EPG-5500.1, ''Guidance for a Hazards Assessment Methodology''). Subsequently, in 1992, DOE published a standard for the performance of Hazards Assessments (DOE-STD-1027-92, ''Hazard Categorization and Accident Analysis, Techniques for Compliance with DOE Order 5480.23, Nuclear Safety Analysis Reports''). Although these documents are a step in the direction of standardization, there remains a great deal of interpretation and subjective implementation in the performance of Hazards Assessments. Rocky Flats Plant has initiated efforts to develop a uniform and standard process to be used for Hazards Assessments

Waste Encapsulation and Storage Facility (WESF) Hazards Assessment

International Nuclear Information System (INIS)

COVEY, L.I.

2000-01-01

This report documents the hazards assessment for the Waste Encapsulation and Storage Facility (WESF) located on the U.S. Department of Energy (DOE) Hanford Site. This hazards assessment was conducted to provide the emergency planning technical basis for WESF. DOE Orders require an emergency planning hazards assessment for each facility that has the potential to reach or exceed the lowest level emergency classification

Hazard waste risk assessment

International Nuclear Information System (INIS)

Hawley, K.A.; Napier, B.A.

1986-01-01

Pacific Northwest Laboratory continued to provide technical assistance to the Department of Energy (DOE) Office of Operational Safety (OOS) in the area of risk assessment for hazardous and radioactive-mixed waste management. The overall objective is to provide technical assistance to OOS in developing cost-effective risk assessment tools and strategies for bringing DOE facilities into compliance with the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA or Superfund) and the Resource Conservation and Recovery Act (RCRA). Major efforts during FY 1985 included (1) completing the modification of the Environmental Protection Agency (EPA) Hazard Ranking System (HRS) and developing training manuals and courses to assist in field office implementation of the modified Hazard Ranking System (mHRS); (2) initiating the development of a system for reviewing field office HRS/mHRS evaluations for appropriate use of data and appropriate application of the methodology; (3) initiating the development of a data base management system to maintain all field office HRS/mHRS scoring sheets and to support the master OOS environmental data base system; (4) developing implementation guidance for Phase I of the DOE CERCLA Program, Installation Assessment; (5) continuing to develop an objective, scientifically based methodology for DOE management to use in establishing priorities for conducting site assessments under Phase II of the DOE CERCLA Program, Confirmation; and (6) participating in developing the DOE response to EPA on the proposed listing of three sites on the National Priorities List

283-E and 283-W hazards assessment

International Nuclear Information System (INIS)

Sutton, L.N.

1994-01-01

This report documents the hazards assessment for the 200 area water treatment plants 283-E and 283-W located on the US DOE Hanford Site. Operation of the water treatment plants is the responsibility of ICF Kaiser Hanford Company (ICF KH). This hazards assessment was conducted to provide emergency planning technical basis for the water treatment plants. This document represents an acceptable interpretation of the implementing guidance document for DOE ORDER 5500.3A which requires an emergency planning hazards assessment for each facility that has the potential to reach or exceed the lowest level emergency classification

Probabilistic tsunami hazard assessment for Point Lepreau Generating Station

Energy Technology Data Exchange (ETDEWEB)

Mullin, D., E-mail: dmullin@nbpower.com [New Brunswick Power Corporation, Point Lepreau Generating Station, Point Lepreau (Canada); Alcinov, T.; Roussel, P.; Lavine, A.; Arcos, M.E.M.; Hanson, K.; Youngs, R., E-mail: trajce.alcinov@amecfw.com, E-mail: patrick.roussel@amecfw.com [AMEC Foster Wheeler Environment & Infrastructure, Dartmouth, NS (Canada)

2015-07-01

In 2012 the Geological Survey of Canada published a preliminary probabilistic tsunami hazard assessment in Open File 7201 that presents the most up-to-date information on all potential tsunami sources in a probabilistic framework on a national level, thus providing the underlying basis for conducting site-specific tsunami hazard assessments. However, the assessment identified a poorly constrained hazard for the Atlantic Coastline and recommended further evaluation. As a result, NB Power has embarked on performing a Probabilistic Tsunami Hazard Assessment (PTHA) for Point Lepreau Generating Station. This paper provides the methodology and progress or hazard evaluation results for Point Lepreau G.S. (author)

Wind hazard assessment for Point Lepreau Generating Station

International Nuclear Information System (INIS)

Mullin, D.; Moland, M.; Sciaudone, J.C.; Twisdale, L.A.; Vickery, P.J.; Mizzen, D.R.

2015-01-01

In response to the CNSC Fukushima Action Plan, NB Power has embarked on a wind hazard assessment for the Point Lepreau Generating Station site that incorporates the latest up to date wind information and modeling. The objective was to provide characterization of the wind hazard from all potential sources and estimate wind-driven missile fragilities and wind pressure fragilities for various structures, systems and components that would provide input to a possible high wind Probabilistic Safety Assessment. The paper will discuss the overall methodology used to assess hazards related to tornadoes, hurricanes and straight-line winds, and site walk-down and hazard/fragility results. (author)

Advanced Manufacturing Processes Laboratory Building 878 hazards assessment document

Energy Technology Data Exchange (ETDEWEB)

Wood, C.; Thornton, W.; Swihart, A.; Gilman, T.

1994-07-01

The introduction of the hazards assessment process is to document the impact of the release of hazards at the Advanced Manufacturing Processes Laboratory (AMPL) that are significant enough to warrant consideration in Sandia National Laboratories` operational emergency management program. This hazards assessment is prepared in accordance with the Department of Energy Order 5500.3A requirement that facility-specific hazards assessments be prepared, maintained, and used for emergency planning purposes. This hazards assessment provides an analysis of the potential airborne release of chemicals associated with the operations and processes at the AMPL. This research and development laboratory develops advanced manufacturing technologies, practices, and unique equipment and provides the fabrication of prototype hardware to meet the needs of Sandia National Laboratories, Albuquerque, New Mexico (SNL/NM). The focus of the hazards assessment is the airborne release of materials because this requires the most rapid, coordinated emergency response on the part of the AMPL, SNL/NM, collocated facilities, and surrounding jurisdiction to protect workers, the public, and the environment.

Advanced Manufacturing Processes Laboratory Building 878 hazards assessment document

International Nuclear Information System (INIS)

Wood, C.; Thornton, W.; Swihart, A.; Gilman, T.

1994-07-01

The introduction of the hazards assessment process is to document the impact of the release of hazards at the Advanced Manufacturing Processes Laboratory (AMPL) that are significant enough to warrant consideration in Sandia National Laboratories' operational emergency management program. This hazards assessment is prepared in accordance with the Department of Energy Order 5500.3A requirement that facility-specific hazards assessments be prepared, maintained, and used for emergency planning purposes. This hazards assessment provides an analysis of the potential airborne release of chemicals associated with the operations and processes at the AMPL. This research and development laboratory develops advanced manufacturing technologies, practices, and unique equipment and provides the fabrication of prototype hardware to meet the needs of Sandia National Laboratories, Albuquerque, New Mexico (SNL/NM). The focus of the hazards assessment is the airborne release of materials because this requires the most rapid, coordinated emergency response on the part of the AMPL, SNL/NM, collocated facilities, and surrounding jurisdiction to protect workers, the public, and the environment

Building 894 hazards assessment document

International Nuclear Information System (INIS)

Banda, Z.; Williams, M.

1996-07-01

The Department of Energy Order 5500.3A requires facility-specific hazards assessments be prepared, maintained, and used for emergency planning purposes. This hazards assessment document describes the chemical and radiological hazards associated with Building 894. The entire inventory was subjected to the screening criteria for potential airborne impact to onsite and offsite individuals out of which 9 chemicals were kept for further evaluation. The air dispersion model, ALOHA, estimated pollutant concentrations downwind from the source of a release, taking into consideration the toxicological and physical characteristics of the release site, the atmospheric conditions, and the circumstances of the release. The greatest distance at which a postulated facility event will produce consequences exceeding the Early Severe Health Effects threshold is 130 meters. The highest emergency classification is a General Emergency. The Emergency Planning Zone is a nominal 130 meter area that conforms to DOE boundaries and physical/jurisdictional boundaries such as fence lines and streets

Building 6630 hazards assessment document

International Nuclear Information System (INIS)

Williams, M.; Banda, Z.

1996-10-01

The Department of Energy Order 5500.3A requires facility-specific hazards assessments be prepared, maintained, and used for emergency planning purposes. This hazards assessment document describes the chemical and radiological hazards associated with Building 6630. The entire inventory was subjected to the screening criteria for potential airborne impact to onsite and offsite individuals out of which one chemical was kept for further evaluation. The air dispersion model, ALOHA, estimated pollutant concentrations downwind from the source of a release, taking into consideration the toxicological and physical characteristics of the chemical release site, the atmospheric conditions, and the circumstances of the release. The greatest distance at which a postulated facility event will produce consequences exceeding the Early Severe Health Effects threshold is 76 meters. The highest emergency classification is an Alert. The Emergency Planning Zone is a nominal 100 meter area that conforms to DOE boundaries and physical/jurisdictional boundaries such as fence lines and streets

Probabilistic seismic hazard assessment of NW and central ...

Indian Academy of Sciences (India)

The Himalayan region has undergone significant development and to ensure safe and secure progress in such a seismically vulnerable region there is a need for hazard assessment. For seismic hazard assessment, it is important to assess the quality, consistency, and homogeneity of the seismicity data collected from ...

Exploration of resilience assessments for natural hazards

Science.gov (United States)

Lo Jacomo, Anna; Han, Dawei; Champneys, Alan

2017-04-01

The occurrence of extreme events due to natural hazards is difficult to predict. Extreme events are stochastic in nature, there is a lack of long term data on their occurrence, and there are still gaps in our understanding of their physical processes. This difficulty in prediction will be exacerbated by climate change and human activities. Yet traditional risk assessments measure risk as the probability of occurrence of a hazard, multiplied by the consequences of the hazard occurring, which ignores the recovery process. In light of the increasing concerns on disaster risks and the related system recovery, resilience assessments are being used as an approach which complements and builds on traditional risk assessments and management. In mechanical terms, resilience refers to the amount of energy per unit volume that a material can absorb while maintaining its ability to return to its original shape. Resilience was first applied in the fields of psychology and ecology, and more recently has been used in areas such as social sciences, economics, and engineering. A common metaphor for understanding resilience is the stability landscape. The landscape consists of a surface of interconnected basins, where each basin represents different states of a system, which is a point on the stability landscape. The resilience of the system is its capacity and tendency to remain within a particular basin. This depends on the topology of the landscape, on the system's current position, and on its reaction to different shocks and stresses. In practical terms, resilience assessments have been conducted for various purposes in different sectors. These assessments vary in their required inputs, the methodologies applied, and the output they produce. Some measures used for resilience assessments are hazard independent. These focus on the intrinsic capabilities of a system, for example the insurance coverage of a community, or the buffer capacity of a water storage reservoir. Other

Supplemental Hazard Analysis and Risk Assessment - Hydrotreater

Energy Technology Data Exchange (ETDEWEB)

Lowry, Peter P. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wagner, Katie A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2015-04-01

A supplemental hazard analysis was conducted and quantitative risk assessment performed in response to an independent review comment received by the Pacific Northwest National Laboratory (PNNL) from the U.S. Department of Energy Pacific Northwest Field Office (PNSO) against the Hydrotreater/Distillation Column Hazard Analysis Report issued in April 2013. The supplemental analysis used the hazardous conditions documented by the previous April 2013 report as a basis. The conditions were screened and grouped for the purpose of identifying whether additional prudent, practical hazard controls could be identified, using a quantitative risk evaluation to assess the adequacy of the controls and establish a lower level of concern for the likelihood of potential serious accidents. Calculations were performed to support conclusions where necessary.

Hazard assessment for Romania–Bulgaria crossborder region

International Nuclear Information System (INIS)

Solakov, Dimcho; Simeonova, Stela; Alexandrova, Irena; Trifonova, Petya; Ardeleanu, Luminita; Cioflan, Carmen

2014-01-01

Among the many kinds of natural and man-made disasters, earthquakes dominate with regard to their social and economical impact on the urban environment. Global seismic hazard and vulnerability to earthquakes are steadily increasing as urbanisation and development occupy more areas that are prone to effects of strong earthquakes. The assessment of the seismic hazard is particularly important, because it provides valuable information for seismic safety and disaster mitigation, and it supports decision making for the benefit of society. The main objective of this study is to assess the seismic hazard for Romania-Bulgaria cross-border region on the basis of integrated basic geo-datasets

Advanced Materials Laboratory hazards assessment document

Energy Technology Data Exchange (ETDEWEB)

Barnett, B.; Banda, Z.

1995-10-01

The Department of Energy Order 55OO.3A requires facility-specific hazards assessments be prepared, maintained, and used for emergency planning purposes. This hazards assessment document describes the chemical and radiological hazards associated with the AML. The entire inventory was screened according to the potential airborne impact to onsite and offsite individuals. The air dispersion model, ALOHA, estimated pollutant concentrations downwind from the source of a release, taking into consideration the toxicological and physical characteristics of the release site, the atmospheric conditions, and the circumstances of the release. The greatest distance at which a postulated facility event will produce consequences exceeding the Early Severe Health Effects threshold is 23 meters. The highest emergency classification is a General Emergency. The Emergency Planning Zone is a nominal area that conforms to DOE boundaries and physical/jurisdictional boundaries such as fence lines and streets.

Conceptual geoinformation model of natural hazards risk assessment

Science.gov (United States)

Kulygin, Valerii

2016-04-01

Natural hazards are the major threat to safe interactions between nature and society. The assessment of the natural hazards impacts and their consequences is important in spatial planning and resource management. Today there is a challenge to advance our understanding of how socio-economical and climate changes will affect the frequency and magnitude of hydro-meteorological hazards and associated risks. However, the impacts from different types of natural hazards on various marine and coastal economic activities are not of the same type. In this study, the conceptual geomodel of risk assessment is presented to highlight the differentiation by the type of economic activities in extreme events risk assessment. The marine and coastal ecosystems are considered as the objects of management, on the one hand, and as the place of natural hazards' origin, on the other hand. One of the key elements in describing of such systems is the spatial characterization of their components. Assessment of ecosystem state is based on ecosystem indicators (indexes). They are used to identify the changes in time. The scenario approach is utilized to account for the spatio-temporal dynamics and uncertainty factors. Two types of scenarios are considered: scenarios of using ecosystem services by economic activities and scenarios of extreme events and related hazards. The reported study was funded by RFBR, according to the research project No. 16-35-60043 mol_a_dk.

Assessing storm erosion hazards

NARCIS (Netherlands)

Ranasinghe, Ranasinghe W M R J B; Callaghan, D.; Ciavola, Paolo; Coco, Giovanni

2017-01-01

The storm erosion hazard on coasts is usually expressed as an erosion volume and/or associated episodic coastline retreat. The accurate assessment of present-day and future storm erosion volumes is a key task for coastal zone managers, planners and engineers. There are four main approaches that can

Flood hazard assessment in areas prone to flash flooding

Science.gov (United States)

Kvočka, Davor; Falconer, Roger A.; Bray, Michaela

2016-04-01

Contemporary climate projections suggest that there will be an increase in the occurrence of high-intensity rainfall events in the future. These precipitation extremes are usually the main cause for the emergence of extreme flooding, such as flash flooding. Flash floods are among the most unpredictable, violent and fatal natural hazards in the world. Furthermore, it is expected that flash flooding will occur even more frequently in the future due to more frequent development of extreme weather events, which will greatly increase the danger to people caused by flash flooding. This being the case, there will be a need for high resolution flood hazard maps in areas susceptible to flash flooding. This study investigates what type of flood hazard assessment methods should be used for assessing the flood hazard to people caused by flash flooding. Two different types of flood hazard assessment methods were tested: (i) a widely used method based on an empirical analysis, and (ii) a new, physically based and experimentally calibrated method. Two flash flood events were considered herein, namely: the 2004 Boscastle flash flood and the 2007 Železniki flash flood. The results obtained in this study suggest that in the areas susceptible to extreme flooding, the flood hazard assessment should be conducted using methods based on a mechanics-based analysis. In comparison to standard flood hazard assessment methods, these physically based methods: (i) take into account all of the physical forces, which act on a human body in floodwater, (ii) successfully adapt to abrupt changes in the flow regime, which often occur for flash flood events, and (iii) rapidly assess a flood hazard index in a relatively short period of time.

Seismic hazard assessment in the Ibero-Maghreb region

Energy Technology Data Exchange (ETDEWEB)

Jimenez, M.J.; Garcia fernandez, M. [Consejo Superior de Investigaciones Cientifcas, Barcelona (Spain). Inst. of Earth Sciences; GSAHP Ibero-Maghreb Working Group

1999-12-01

The paper illustrates the contribution of the Ibero-Maghreb region to the global GSHAP (Global Seismic Hazard Assessment Program) map: for the first time, a map of regional hazard source zones is presented and agreement on a common procedure for hazard computation in the region has been achieved.

Emergency preparedness hazards assessment for selected 100 Area Bechtel Hanford, Inc. facilities

International Nuclear Information System (INIS)

1997-07-01

The emergency preparedness hazards assessment for Bechtel Hanford Inc. (BHI) facilities in the 100 Areas of the Hanford Site. The purpose of a hazards assessment is to identify the hazardous material at each facility, identify the conditions that could release the hazardous material, and calculate the consequences of the releases. The hazards assessment is the technical basis for the facility emergency plans and procedures. There are many other buildings and past- practice burial grounds, trenches, cribs, etc., in the 100 Areas that may contain hazardous materials. Undisturbed buried waste sites that are not near the Columbia River are outside the scope of emergency preparedness hazards assessments because there is no mechanism for acute release to the air or ground water. The sites near the Columbia River are considered in a separate flood hazards assessment. This hazards assessment includes only the near-term soil remediation projects that involve intrusive activities

Volcanic Hazard Assessments for Nuclear Installations: Methods and Examples in Site Evaluation

International Nuclear Information System (INIS)

2016-07-01

To provide guidance on the protection of nuclear installations against the effects of volcanoes, the IAEA published in 2012 IAEA Safety Standards Series No. SSG-21, Volcanic Hazards in Site Evaluation for Nuclear Installations. SSG-21 addresses hazards relating to volcanic phenomena, and provides recommendations and general guidance for evaluation of these hazards. Unlike seismic hazard assessments, models for volcanic hazard assessment have not undergone decades of review, evaluation and testing for suitability in evaluating hazards at proposed nuclear installations. Currently in volcanology, scientific developments and detailed methodologies to model volcanic phenomena are evolving rapidly.This publication provides information on detailed methodologies and examples in the application of volcanic hazard assessment to site evaluation for nuclear installations, thereby addressing the recommendations in SSG-21. Although SSG-21 develops a logical framework for conducting a volcanic hazard assessment, this publication demonstrates the practicability of evaluating the recommendations in SSG-21 through a systematic volcanic hazard assessment and examples from Member States. The results of this hazard assessment can be used to derive the appropriate design bases and operational considerations for specific nuclear installations

Landslides Hazard Assessment Using Different Approaches

Directory of Open Access Journals (Sweden)

Coman Cristina

2017-06-01

Full Text Available Romania represents one of Europe’s countries with high landslides occurrence frequency. Landslide hazard maps are designed by considering the interaction of several factors which, by their joint action may affect the equilibrium state of the natural slopes. The aim of this paper is landslides hazard assessment using the methodology provided by the Romanian national legislation and a very largely used statistical method. The final results of these two analyses are quantitative or semi-quantitative landslides hazard maps, created in geographic information system environment. The data base used for this purpose includes: geological and hydrogeological data, digital terrain model, hydrological data, land use, seismic action, anthropic action and an inventory of active landslides. The GIS landslides hazard models were built for the geographical area of the Iasi city, located in the north-east side of Romania.

Seismic hazard assessment of the Hanford region, Eastern Washington State

International Nuclear Information System (INIS)

Youngs, R.R.; Coppersmith, K.J.; Power, M.S.; Swan, F.H. III

1985-01-01

A probabilistic seismic hazard assessment was made for a site within the Hanford region of eastern Washington state, which is characterized as an intraplate region having a relatively low rate of seismic activity. Probabilistic procedures, such as logic trees, were utilized to account for the uncertainties in identifying and characterizing the potential seismic sources in the region. Logic trees provide a convenient, flexible means of assessing the values and relative likelihoods of input parameters to the hazard model that may be dependent upon each other. Uncertainties accounted for in this way include the tectonic model, segmentation, capability, fault geometry, maximum earthquake magnitude, and earthquake recurrence rate. The computed hazard results are expressed as a distribution from which confidence levels are assessed. Analysis of the results show the contributions to the total hazard from various seismic sources and due to various earthquake magnitudes. In addition, the contributions of uncertainties in the various source parameters to the uncertainty in the computed hazard are assessed. For this study, the major contribution to uncertainty in the computed hazard are due to uncertainties in the applicable tectonic model and the earthquake recurrence rate. This analysis serves to illustrate some of the probabilistic tools that are available for conducting seismic hazard assessments and for analyzing the results of these studies. 5 references, 7 figures

Kauai Test Facility hazards assessment document

Energy Technology Data Exchange (ETDEWEB)

Swihart, A

1995-05-01

The Department of Energy Order 55003A requires facility-specific hazards assessment be prepared, maintained, and used for emergency planning purposes. This hazards assessment document describes the chemical and radiological hazards associated with the Kauai Test Facility, Barking Sands, Kauai, Hawaii. The Kauai Test Facility`s chemical and radiological inventories were screened according to potential airborne impact to onsite and offsite individuals. The air dispersion model, ALOHA, estimated pollutant concentrations downwind from the source of a release, taking into consideration the toxicological and physical characteristics of the release site, the atmospheric conditions, and the circumstances of the release. The greatest distance to the Early Severe Health Effects threshold is 4.2 kilometers. The highest emergency classification is a General Emergency at the {open_quotes}Main Complex{close_quotes} and a Site Area Emergency at the Kokole Point Launch Site. The Emergency Planning Zone for the {open_quotes}Main Complex{close_quotes} is 5 kilometers. The Emergency Planning Zone for the Kokole Point Launch Site is the Pacific Missile Range Facility`s site boundary.

Kauai Test Facility hazards assessment document

International Nuclear Information System (INIS)

Swihart, A.

1995-05-01

The Department of Energy Order 55003A requires facility-specific hazards assessment be prepared, maintained, and used for emergency planning purposes. This hazards assessment document describes the chemical and radiological hazards associated with the Kauai Test Facility, Barking Sands, Kauai, Hawaii. The Kauai Test Facility's chemical and radiological inventories were screened according to potential airborne impact to onsite and offsite individuals. The air dispersion model, ALOHA, estimated pollutant concentrations downwind from the source of a release, taking into consideration the toxicological and physical characteristics of the release site, the atmospheric conditions, and the circumstances of the release. The greatest distance to the Early Severe Health Effects threshold is 4.2 kilometers. The highest emergency classification is a General Emergency at the open-quotes Main Complexclose quotes and a Site Area Emergency at the Kokole Point Launch Site. The Emergency Planning Zone for the open-quotes Main Complexclose quotes is 5 kilometers. The Emergency Planning Zone for the Kokole Point Launch Site is the Pacific Missile Range Facility's site boundary

Toward uniform probabilistic seismic hazard assessments for Southeast Asia

Science.gov (United States)

Chan, C. H.; Wang, Y.; Shi, X.; Ornthammarath, T.; Warnitchai, P.; Kosuwan, S.; Thant, M.; Nguyen, P. H.; Nguyen, L. M.; Solidum, R., Jr.; Irsyam, M.; Hidayati, S.; Sieh, K.

2017-12-01

Although most Southeast Asian countries have seismic hazard maps, various methodologies and quality result in appreciable mismatches at national boundaries. We aim to conduct a uniform assessment across the region by through standardized earthquake and fault databases, ground-shaking scenarios, and regional hazard maps. Our earthquake database contains earthquake parameters obtained from global and national seismic networks, harmonized by removal of duplicate events and the use of moment magnitude. Our active-fault database includes fault parameters from previous studies and from the databases implemented for national seismic hazard maps. Another crucial input for seismic hazard assessment is proper evaluation of ground-shaking attenuation. Since few ground-motion prediction equations (GMPEs) have used local observations from this region, we evaluated attenuation by comparison of instrumental observations and felt intensities for recent earthquakes with predicted ground shaking from published GMPEs. We then utilize the best-fitting GMPEs and site conditions into our seismic hazard assessments. Based on the database and proper GMPEs, we have constructed regional probabilistic seismic hazard maps. The assessment shows highest seismic hazard levels near those faults with high slip rates, including the Sagaing Fault in central Myanmar, the Sumatran Fault in Sumatra, the Palu-Koro, Matano and Lawanopo Faults in Sulawesi, and the Philippine Fault across several islands of the Philippines. In addition, our assessment demonstrates the important fact that regions with low earthquake probability may well have a higher aggregate probability of future earthquakes, since they encompass much larger areas than the areas of high probability. The significant irony then is that in areas of low to moderate probability, where building codes are usually to provide less seismic resilience, seismic risk is likely to be greater. Infrastructural damage in East Malaysia during the 2015

Risk assessment on hazards for decommissioning safety of a nuclear facility

International Nuclear Information System (INIS)

Jeong, Kwan-Seong; Lee, Kune-Woo; Lim, Hyeon-Kyo

2010-01-01

A decommissioning plan should be followed by a qualitative and quantitative safety assessment of it. The safety assessment of a decommissioning plan is applied to identify the potential (radiological and non-radiological) hazards and risks. Radiological and non-radiological hazards arise during decommissioning activities. The non-radiological or industrial hazards to which workers are subjected during a decommissioning and dismantling process may be greater than those experienced during an operational lifetime of a facility. Workers need to be protected by eliminating or reducing the radiological and non-radiological hazards that may arise during routine decommissioning activities and as well as during accidents. The risk assessment method was developed by using risk matrix and fuzzy inference logic, on the basis of the radiological and non-radiological hazards for a decommissioning safety of a nuclear facility. Fuzzy inference of radiological and non-radiological hazards performs a mapping from radiological and non-radiological hazards to risk matrix. Defuzzification of radiological and non-radiological hazards is the conversion of risk matrix and priorities to the maximum criterion method and the mean criterion method. In the end, a composite risk assessment methodology, to rank the risk level on radiological and non-radiological hazards of the decommissioning tasks and to prioritize on the risk level of the decommissioning tasks, by simultaneously combining radiological and non-radiological hazards, was developed.

OpenQuake, a platform for collaborative seismic hazard and risk assessment

Science.gov (United States)

Henshaw, Paul; Burton, Christopher; Butler, Lars; Crowley, Helen; Danciu, Laurentiu; Nastasi, Matteo; Monelli, Damiano; Pagani, Marco; Panzeri, Luigi; Simionato, Michele; Silva, Vitor; Vallarelli, Giuseppe; Weatherill, Graeme; Wyss, Ben

2013-04-01

Sharing of data and risk information, best practices, and approaches across the globe is key to assessing risk more effectively. Through global projects, open-source IT development and collaborations with more than 10 regions, leading experts are collaboratively developing unique global datasets, best practice, tools and models for global seismic hazard and risk assessment, within the context of the Global Earthquake Model (GEM). Guided by the needs and experiences of governments, companies and international organisations, all contributions are being integrated into OpenQuake: a web-based platform that - together with other resources - will become accessible in 2014. With OpenQuake, stakeholders worldwide will be able to calculate, visualize and investigate earthquake hazard and risk, capture new data and share findings for joint learning. The platform is envisaged as a collaborative hub for earthquake risk assessment, used at global and local scales, around which an active network of users has formed. OpenQuake will comprise both online and offline tools, many of which can also be used independently. One of the first steps in OpenQuake development was the creation of open-source software for advanced seismic hazard and risk calculations at any scale, the OpenQuake Engine. Although in continuous development, a command-line version of the software is already being test-driven and used by hundreds worldwide; from non-profits in Central Asia, seismologists in sub-Saharan Africa and companies in South Asia to the European seismic hazard harmonization programme (SHARE). In addition, several technical trainings were organized with scientists from different regions of the world (sub-Saharan Africa, Central Asia, Asia-Pacific) to introduce the engine and other OpenQuake tools to the community, something that will continue to happen over the coming years. Other tools that are being developed of direct interest to the hazard community are: • OpenQuake Modeller; fundamental

Application of the Coastal Hazard Wheel methodology for coastal multi-hazard assessment and management in the state of Djibouti

Directory of Open Access Journals (Sweden)

Lars Rosendahl Appelquist

2014-01-01

Full Text Available This paper presents the application of a new methodology for coastal multi-hazard assessment and management in a changing global climate on the state of Djibouti. The methodology termed the Coastal Hazard Wheel (CHW is developed for worldwide application and is based on a specially designed coastal classification system that incorporates the main static and dynamic parameters determining the characteristics of a coastal environment. The methodology provides information on the hazards of ecosystem disruption, gradual inundation, salt water intrusion, erosion and flooding and can be used to support management decisions at local, regional and national level, in areas with limited access to geophysical data. The assessment for Djibouti applies a geographic information system (GIS to develop a range of national hazard maps along with relevant hazard statistics and is showcasing the procedure for applying the CHW methodology for national hazard assessments. The assessment shows that the coastline of Djibouti is characterized by extensive stretches with high or very high hazards of ecosystem disruption, mainly related to coral reefs and mangrove forests, while large sections along the coastlines of especially northern and southern Djibouti have high hazard levels for gradual inundation. The hazard of salt water intrusion is moderate along most of Djibouti’s coastline, although groundwater availability is considered to be very sensitive to human ground water extraction. High or very high erosion hazards are associated with Djibouti’s sedimentary plains, estuaries and river mouths, while very high flooding hazards are associated with the dry river mouths.

Satellite-Based Assessment of Rainfall-Triggered Landslide Hazard for Situational Awareness

Science.gov (United States)

Kirschbaum, Dalia; Stanley, Thomas

2018-03-01

Determining the time, location, and severity of natural disaster impacts is fundamental to formulating mitigation strategies, appropriate and timely responses, and robust recovery plans. A Landslide Hazard Assessment for Situational Awareness (LHASA) model was developed to indicate potential landslide activity in near real-time. LHASA combines satellite-based precipitation estimates with a landslide susceptibility map derived from information on slope, geology, road networks, fault zones, and forest loss. Precipitation data from the Global Precipitation Measurement (GPM) mission are used to identify rainfall conditions from the past 7 days. When rainfall is considered to be extreme and susceptibility values are moderate to very high, a "nowcast" is issued to indicate the times and places where landslides are more probable. When LHASA nowcasts were evaluated with a Global Landslide Catalog, the probability of detection (POD) ranged from 8% to 60%, depending on the evaluation period, precipitation product used, and the size of the spatial and temporal window considered around each landslide point. Applications of the LHASA system are also discussed, including how LHASA is used to estimate long-term trends in potential landslide activity at a nearly global scale and how it can be used as a tool to support disaster risk assessment. LHASA is intended to provide situational awareness of landslide hazards in near real-time, providing a flexible, open-source framework that can be adapted to other spatial and temporal scales based on data availability.

Probabilistic seismic hazard assessment for Point Lepreau Generating Station

Energy Technology Data Exchange (ETDEWEB)

Mullin, D. [New Brunswick Power Corp., Point Lepreau Generating Station, Lepreau, New Brunswick (Canada); Lavine, A. [AMEC Foster Wheeler Environment and Infrastructure Americas, Oakland, California (United States); Egan, J. [SAGE Engineers, Oakland, California (United States)

2015-09-15

A Probabilistic Seismic Hazard Assessment (PSHA) has been performed for the Point Lepreau Generating Station (PLGS). The objective is to provide characterization of the earthquake ground shaking that will be used to evaluate seismic safety. The assessment is based on the current state of knowledge of the informed scientific and engineering community regarding earthquake hazards in the site region, and includes two primary components-a seismic source model and a ground motion model. This paper provides the methodology and results of the PLGS PSHA. The implications of the updated hazard information for site safety are discussed in a separate paper. (author)

Probabilistic seismic hazard assessment for Point Lepreau Generating Station

Energy Technology Data Exchange (ETDEWEB)

Mullin, D., E-mail: dmullin@nbpower.com [New Brunswick Power Corporation, Point Lepreau Generating Station, Point Lepreau, NB (Canada); Lavine, A., E-mail: alexis.lavine@amecfw.com [AMEC Foster Wheeler Environment & Infrastructure Americas, Oakland, CA (United States); Egan, J., E-mail: jegan@sageengineers.com [SAGE Engineers, Oakland, CA (United States)

2015-07-01

A Probabilistic Seismic Hazard Assessment (PSHA) has been performed for the Point Lepreau Generating Station (PLGS). The objective is to provide characterization of the earthquake ground shaking that will be used to evaluate seismic safety. The assessment is based on the current state of knowledge of the informed scientific and engineering community regarding earthquake hazards in the site region, and includes two primary components--a seismic source model and a ground motion model. This paper provides the methodology and results of the PLGS PSHA. The implications of the updated hazard information for site safety are discussed in a separate paper. (author)

Innovative assesment of the seismic hazard from Vrancea sources

International Nuclear Information System (INIS)

Panza, Giuliano Francesco

2002-01-01

In the framework of a very fruitful, stimulating and still ongoing collaboration between the National Institute for Earth Physics - Bucharest, the Department of Earth Sciences - University of Trieste and The Abdus Salam International Center for Theoretical Physics - SAND Group, several innovative steps forwards have been made in the assessment of the seismic hazard generated by Vrancea seismicity. The limits of currently applied probabilistic approaches are partly overcome by the introduction of hazard scenarios based on the deterministic, realistic modeling of ground motion. The ongoing co-operation represents a fundamental contribution to the reliable assessment of seismic hazard, and has been recently enriched by the participation of Bulgarian scientists, who are facing, in the urban settlements close to the Romanian border, a seismic hazard similar to the one in Bucharest. (author)

Probabilistic Seismic Hazard Assessment for Northeast India Region

Science.gov (United States)

Das, Ranjit; Sharma, M. L.; Wason, H. R.

2016-08-01

Northeast India bounded by latitudes 20°-30°N and longitudes 87°-98°E is one of the most seismically active areas in the world. This region has experienced several moderate-to-large-sized earthquakes, including the 12 June, 1897 Shillong earthquake ( M w 8.1) and the 15 August, 1950 Assam earthquake ( M w 8.7) which caused loss of human lives and significant damages to buildings highlighting the importance of seismic hazard assessment for the region. Probabilistic seismic hazard assessment of the region has been carried out using a unified moment magnitude catalog prepared by an improved General Orthogonal Regression methodology (Geophys J Int, 190:1091-1096, 2012; Probabilistic seismic hazard assessment of Northeast India region, Ph.D. Thesis, Department of Earthquake Engineering, IIT Roorkee, Roorkee, 2013) with events compiled from various databases (ISC, NEIC,GCMT, IMD) and other available catalogs. The study area has been subdivided into nine seismogenic source zones to account for local variation in tectonics and seismicity characteristics. The seismicity parameters are estimated for each of these source zones, which are input variables into seismic hazard estimation of a region. The seismic hazard analysis of the study region has been performed by dividing the area into grids of size 0.1° × 0.1°. Peak ground acceleration (PGA) and spectral acceleration ( S a) values (for periods of 0.2 and 1 s) have been evaluated at bedrock level corresponding to probability of exceedance (PE) of 50, 20, 10, 2 and 0.5 % in 50 years. These exceedance values correspond to return periods of 100, 225, 475, 2475, and 10,000 years, respectively. The seismic hazard maps have been prepared at the bedrock level, and it is observed that the seismic hazard estimates show a significant local variation in contrast to the uniform hazard value suggested by the Indian standard seismic code [Indian standard, criteria for earthquake-resistant design of structures, fifth edition, Part

Probabilistic Tsunami Hazard Assessment: the Seaside, Oregon Pilot Study

Science.gov (United States)

Gonzalez, F. I.; Geist, E. L.; Synolakis, C.; Titov, V. V.

2004-12-01

A pilot study of Seaside, Oregon is underway, to develop methodologies for probabilistic tsunami hazard assessments that can be incorporated into Flood Insurance Rate Maps (FIRMs) developed by FEMA's National Flood Insurance Program (NFIP). Current NFIP guidelines for tsunami hazard assessment rely on the science, technology and methodologies developed in the 1970s; although generally regarded as groundbreaking and state-of-the-art for its time, this approach is now superseded by modern methods that reflect substantial advances in tsunami research achieved in the last two decades. In particular, post-1990 technical advances include: improvements in tsunami source specification; improved tsunami inundation models; better computational grids by virtue of improved bathymetric and topographic databases; a larger database of long-term paleoseismic and paleotsunami records and short-term, historical earthquake and tsunami records that can be exploited to develop improved probabilistic methodologies; better understanding of earthquake recurrence and probability models. The NOAA-led U.S. National Tsunami Hazard Mitigation Program (NTHMP), in partnership with FEMA, USGS, NSF and Emergency Management and Geotechnical agencies of the five Pacific States, incorporates these advances into site-specific tsunami hazard assessments for coastal communities in Alaska, California, Hawaii, Oregon and Washington. NTHMP hazard assessment efforts currently focus on developing deterministic, "credible worst-case" scenarios that provide valuable guidance for hazard mitigation and emergency management. The NFIP focus, on the other hand, is on actuarial needs that require probabilistic hazard assessments such as those that characterize 100- and 500-year flooding events. There are clearly overlaps in NFIP and NTHMP objectives. NTHMP worst-case scenario assessments that include an estimated probability of occurrence could benefit the NFIP; NFIP probabilistic assessments of 100- and 500-yr

Are seismic hazard assessment errors and earthquake surprises unavoidable?

Science.gov (United States)

Kossobokov, Vladimir

2013-04-01

Why earthquake occurrences bring us so many surprises? The answer seems evident if we review the relationships that are commonly used to assess seismic hazard. The time-span of physically reliable Seismic History is yet a small portion of a rupture recurrence cycle at an earthquake-prone site, which makes premature any kind of reliable probabilistic statements about narrowly localized seismic hazard. Moreover, seismic evidences accumulated to-date demonstrate clearly that most of the empirical relations commonly accepted in the early history of instrumental seismology can be proved erroneous when testing statistical significance is applied. Seismic events, including mega-earthquakes, cluster displaying behaviors that are far from independent or periodic. Their distribution in space is possibly fractal, definitely, far from uniform even in a single segment of a fault zone. Such a situation contradicts generally accepted assumptions used for analytically tractable or computer simulations and complicates design of reliable methodologies for realistic earthquake hazard assessment, as well as search and definition of precursory behaviors to be used for forecast/prediction purposes. As a result, the conclusions drawn from such simulations and analyses can MISLEAD TO SCIENTIFICALLY GROUNDLESS APPLICATION, which is unwise and extremely dangerous in assessing expected societal risks and losses. For example, a systematic comparison of the GSHAP peak ground acceleration estimates with those related to actual strong earthquakes, unfortunately, discloses gross inadequacy of this "probabilistic" product, which appears UNACCEPTABLE FOR ANY KIND OF RESPONSIBLE SEISMIC RISK EVALUATION AND KNOWLEDGEABLE DISASTER PREVENTION. The self-evident shortcomings and failures of GSHAP appeals to all earthquake scientists and engineers for an urgent revision of the global seismic hazard maps from the first principles including background methodologies involved, such that there becomes: (a) a

Urban Heat Wave Hazard Assessment

Science.gov (United States)

Quattrochi, D. A.; Jedlovec, G.; Crane, D. L.; Meyer, P. J.; LaFontaine, F.

2016-12-01

Heat waves are one of the largest causes of environmentally-related deaths globally and are likely to become more numerous as a result of climate change. The intensification of heat waves by the urban heat island effect and elevated humidity, combined with urban demographics, are key elements leading to these disasters. Better warning of the potential hazards may help lower risks associated with heat waves. Moderate resolution thermal data from NASA satellites is used to derive high spatial resolution estimates of apparent temperature (heat index) over urban regions. These data, combined with demographic data, are used to produce a daily heat hazard/risk map for selected cities. MODIS data are used to derive daily composite maximum and minimum land surface temperature (LST) fields to represent the amplitude of the diurnal temperature cycle and identify extreme heat days. Compositing routines are used to generate representative daily maximum and minimum LSTs for the urban environment. The limited effect of relative humidity on the apparent temperature (typically 10-15%) allows for the use of modeled moisture fields to convert LST to apparent temperature without loss of spatial variability. The daily max/min apparent temperature fields are used to identify abnormally extreme heat days relative to climatological values in order to produce a heat wave hazard map. Reference to climatological values normalizes the hazard for a particular region (e.g., the impact of an extreme heat day). A heat wave hazard map has been produced for several case study periods and then computed on a quasi-operational basis during the summer of 2016 for Atlanta, GA, Chicago, IL, St. Louis, MO, and Huntsville, AL. A hazard does not become a risk until someone or something is exposed to that hazard at a level that might do harm. Demographic information is used to assess the urban risk associated with the heat wave hazard. Collectively, the heat wave hazard product can warn people in urban

Oak Ridge Y-12 Plant Emergency Management Hazards Assessment (EMHA) Process

International Nuclear Information System (INIS)

Bailiff, E.G.; Bolling, J.D.

2000-01-01

This report establishes requirements and standard methods for the development and maintenance of the Emergency Management Hazards Assessment (EMHA) process used by the lead and all event contractors at the Y-12 Plant for emergency planning and preparedness. The EMHA process provides the technical basis for the Y-12 emergency management program. The instructions provides in this report include methods and requirements for performing the following emergency management activities at Y-12: hazards identification; hazards survey, and hazards assessment

Aiding alternatives assessment with an uncertainty-tolerant hazard scoring method.

Science.gov (United States)

Faludi, Jeremy; Hoang, Tina; Gorman, Patrick; Mulvihill, Martin

2016-11-01

This research developed a single-score system to simplify and clarify decision-making in chemical alternatives assessment, accounting for uncertainty. Today, assessing alternatives to hazardous constituent chemicals is a difficult task-rather than comparing alternatives by a single definitive score, many independent toxicological variables must be considered at once, and data gaps are rampant. Thus, most hazard assessments are only comprehensible to toxicologists, but business leaders and politicians need simple scores to make decisions. In addition, they must balance hazard against other considerations, such as product functionality, and they must be aware of the high degrees of uncertainty in chemical hazard data. This research proposes a transparent, reproducible method to translate eighteen hazard endpoints into a simple numeric score with quantified uncertainty, alongside a similar product functionality score, to aid decisions between alternative products. The scoring method uses Clean Production Action's GreenScreen as a guide, but with a different method of score aggregation. It provides finer differentiation between scores than GreenScreen's four-point scale, and it displays uncertainty quantitatively in the final score. Displaying uncertainty also illustrates which alternatives are early in product development versus well-defined commercial products. This paper tested the proposed assessment method through a case study in the building industry, assessing alternatives to spray polyurethane foam insulation containing methylene diphenyl diisocyanate (MDI). The new hazard scoring method successfully identified trade-offs between different alternatives, showing finer resolution than GreenScreen Benchmarking. Sensitivity analysis showed that different weighting schemes in hazard scores had almost no effect on alternatives ranking, compared to uncertainty from data gaps. Copyright © 2016 Elsevier Ltd. All rights reserved.

Rockfall Hazard Process Assessment : Implementation Report

Science.gov (United States)

2017-10-01

The Montana Department of Transportation (MDT) commissioned a new research program to improve assessment and management of its rock slope assets. The Department implemented a Rockfall Hazard Rating System (RHRS) program in 2005 and wished to add valu...

Wicked Problems in Natural Hazard Assessment and Mitigation

Science.gov (United States)

Stein, S.; Steckler, M. S.; Rundle, J. B.; Dixon, T. H.

2017-12-01

Social scientists have defined "wicked" problems that are "messy, ill-defined, more complex than we fully grasp, and open to multiple interpretations based on one's point of view... No solution to a wicked problem is permanent or wholly satisfying, which leaves every solution open to easy polemical attack." These contrast with "tame" problems in which necessary information is available and solutions - even if difficult and expensive - are straightforward to identify and execute. Updating the U.S.'s aging infrastructure is a tame problem, because what is wrong and how to fix it are clear. In contrast, addressing climate change is a wicked problem because its effects are uncertain and the best strategies to address them are unclear. An analogous approach can be taken to natural hazard problems. In tame problems, we have a good model of the process, good information about past events, and data implying that the model should predict future events. In such cases, we can make a reasonable assessment of the hazard that can be used to develop mitigation strategies. Earthquake hazard mitigation for San Francisco is a relatively tame problem. We understand how the earthquakes result from known plate motions, have information about past earthquakes, and have geodetic data implying that future similar earthquakes will occur. As a result, it is straightforward to develop and implement mitigation strategies. However, in many cases, hazard assessment and mitigation is a wicked problem. How should we prepare for a great earthquake on plate boundaries where tectonics favor such events but we have no evidence that they have occurred and hence how large they may be or how often to expect them? How should we assess the hazard within plates, for example in the New Madrid seismic zone, where large earthquakes have occurred but we do not understand their causes and geodetic data show no strain accumulating? How can we assess the hazard and make sensible policy when the recurrence of

LAV@HAZARD: a web-GIS interface for volcanic hazard assessment

Directory of Open Access Journals (Sweden)

Giovanni Gallo

2011-12-01

Full Text Available Satellite data, radiative power of hot spots as measured with remote sensing, historical records, on site geological surveys, digital elevation model data, and simulation results together provide a massive data source to investigate the behavior of active volcanoes like Mount Etna (Sicily, Italy over recent times. The integration of these heterogeneous data into a coherent visualization framework is important for their practical exploitation. It is crucial to fill in the gap between experimental and numerical data, and the direct human perception of their meaning. Indeed, the people in charge of safety planning of an area need to be able to quickly assess hazards and other relevant issues even during critical situations. With this in mind, we developed LAV@HAZARD, a web-based geographic information system that provides an interface for the collection of all of the products coming from the LAVA project research activities. LAV@HAZARD is based on Google Maps application programming interface, a choice motivated by its ease of use and the user-friendly interactive environment it provides. In particular, the web structure consists of four modules for satellite applications (time-space evolution of hot spots, radiant flux and effusion rate, hazard map visualization, a database of ca. 30,000 lava-flow simulations, and real-time scenario forecasting by MAGFLOW on Compute Unified Device Architecture.

Waste receiving and processing (WRAP) module 1 hazards assessment. Revision 1

International Nuclear Information System (INIS)

Sutton, L.N.

1997-01-01

This report documents the hazards assessment for the Waste Receiving and Processing Module I (WRAP 1) located on the U.S. Department of Energy (DOE) Hanford Site. Operation of the WRAP 1 is the responsibility of Rust Federal Services Hanford (RFSH). This hazards assessment was conducted to provide the emergency planning technical basis for the WRAP 1. DOE Orders require an emergency planning hazards assessment for each facility that has the potential to reach or exceed the lowest level emergency classification

Probabilistic seismic hazard assessment of southern part of Ghana

Science.gov (United States)

Ahulu, Sylvanus T.; Danuor, Sylvester Kojo; Asiedu, Daniel K.

2018-05-01

This paper presents a seismic hazard map for the southern part of Ghana prepared using the probabilistic approach, and seismic hazard assessment results for six cities. The seismic hazard map was prepared for 10% probability of exceedance for peak ground acceleration in 50 years. The input parameters used for the computations of hazard were obtained using data from a catalogue that was compiled and homogenised to moment magnitude (Mw). The catalogue covered a period of over a century (1615-2009). The hazard assessment is based on the Poisson model for earthquake occurrence, and hence, dependent events were identified and removed from the catalogue. The following attenuation relations were adopted and used in this study—Allen (for south and eastern Australia), Silva et al. (for Central and eastern North America), Campbell and Bozorgnia (for worldwide active-shallow-crust regions) and Chiou and Youngs (for worldwide active-shallow-crust regions). Logic-tree formalism was used to account for possible uncertainties associated with the attenuation relationships. OpenQuake software package was used for the hazard calculation. The highest level of seismic hazard is found in the Accra and Tema seismic zones, with estimated peak ground acceleration close to 0.2 g. The level of the seismic hazard in the southern part of Ghana diminishes with distance away from the Accra/Tema region to a value of 0.05 g at a distance of about 140 km.

Probabilistic seismic hazard assessment of southern part of Ghana

Science.gov (United States)

Ahulu, Sylvanus T.; Danuor, Sylvester Kojo; Asiedu, Daniel K.

2017-12-01

This paper presents a seismic hazard map for the southern part of Ghana prepared using the probabilistic approach, and seismic hazard assessment results for six cities. The seismic hazard map was prepared for 10% probability of exceedance for peak ground acceleration in 50 years. The input parameters used for the computations of hazard were obtained using data from a catalogue that was compiled and homogenised to moment magnitude (Mw). The catalogue covered a period of over a century (1615-2009). The hazard assessment is based on the Poisson model for earthquake occurrence, and hence, dependent events were identified and removed from the catalogue. The following attenuation relations were adopted and used in this study—Allen (for south and eastern Australia), Silva et al. (for Central and eastern North America), Campbell and Bozorgnia (for worldwide active-shallow-crust regions) and Chiou and Youngs (for worldwide active-shallow-crust regions). Logic-tree formalism was used to account for possible uncertainties associated with the attenuation relationships. OpenQuake software package was used for the hazard calculation. The highest level of seismic hazard is found in the Accra and Tema seismic zones, with estimated peak ground acceleration close to 0.2 g. The level of the seismic hazard in the southern part of Ghana diminishes with distance away from the Accra/Tema region to a value of 0.05 g at a distance of about 140 km.

Simulation Technology Laboratory Building 970 hazards assessment document

International Nuclear Information System (INIS)

Wood, C.L.; Starr, M.D.

1994-11-01

The Department of Energy Order 5500.3A requires facility-specific hazards assessments be prepared, maintained, and used for emergency planning purposes. This hazards assessment document describes the chemical and radiological hazards associated with the Simulation Technology Laboratory, Building 970. The entire inventory was screened according to the potential airborne impact to onsite and offsite individuals. The air dispersion model, ALOHA, estimated pollutant concentrations downwind from the source of a release, taking into consideration the toxicological and physical characteristics of the release site, the atmospheric conditions, and the circumstances of the release. The greatest distances at which a postulated facility event will produce consequences exceeding the ERPG-2 and Early Severe Health Effects thresholds are 78 and 46 meters, respectively. The highest emergency classification is a Site Area Emergency. The Emergency Planning Zone is 100 meters

The Spatial Assessment of the Current Seismic Hazard State for Hard Rock Underground Mines

Science.gov (United States)

Wesseloo, Johan

2018-06-01

Mining-induced seismic hazard assessment is an important component in the management of safety and financial risk in mines. As the seismic hazard is a response to the mining activity, it is non-stationary and variable both in space and time. This paper presents an approach for implementing a probabilistic seismic hazard assessment to assess the current hazard state of a mine. Each of the components of the probabilistic seismic hazard assessment is considered within the context of hard rock underground mines. The focus of this paper is the assessment of the in-mine hazard distribution and does not consider the hazard to nearby public or structures. A rating system and methodologies to present hazard maps, for the purpose of communicating to different stakeholders in the mine, i.e. mine managers, technical personnel and the work force, are developed. The approach allows one to update the assessment with relative ease and within short time periods as new data become available, enabling the monitoring of the spatial and temporal change in the seismic hazard.

Detailed debris flow hazard assessment in Andorra: A multidisciplinary approach

Science.gov (United States)

Hürlimann, Marcel; Copons, Ramon; Altimir, Joan

2006-08-01

In many mountainous areas, the rapid development of urbanisation and the limited space in the valley floors have created a need to construct buildings in zones potentially exposed to debris flow hazard. In these zones, a detailed and coherent hazard assessment is necessary to provide an adequate urban planning. This article presents a multidisciplinary procedure to evaluate the debris flow hazard at a local scale. Our four-step approach was successfully applied to five torrent catchments in the Principality of Andorra, located in the Pyrenees. The first step consisted of a comprehensive geomorphologic and geologic analysis providing an inventory map of the past debris flows, a magnitude-frequency relationship, and a geomorphologic-geologic map. These data were necessary to determine the potential initiation zones and volumes of future debris flows for each catchment. A susceptibility map and different scenarios were the principal outcome of the first step, as well as essential input data for the second step, the runout analysis. A one-dimensional numerical code was applied to analyse the scenarios previously defined. First, the critical channel sections in the fan area were evaluated, then the maximum runout of the debris flows on the fan was studied, and finally simplified intensity maps for each defined scenario were established. The third step of our hazard assessment was the hazard zonation and the compilation of all the results from the two previous steps in a final hazard map. The base of this hazard map was the hazard matrix, which combined the intensity of the debris flow with its probability of occurrence and determined a certain hazard degree. The fourth step referred to the hazard mitigation and included some recommendations for hazard reduction. In Andorra, this four-step approach is actually being applied to assess the debris flow hazard. The final hazard maps, at 1 : 2000 scale, provide an obligatory tool for local land use planning. Experience

Earthquake hazard assessment and small earthquakes

International Nuclear Information System (INIS)

Reiter, L.

1987-01-01

The significance of small earthquakes and their treatment in nuclear power plant seismic hazard assessment is an issue which has received increased attention over the past few years. In probabilistic studies, sensitivity studies showed that the choice of the lower bound magnitude used in hazard calculations can have a larger than expected effect on the calculated hazard. Of particular interest is the fact that some of the difference in seismic hazard calculations between the Lawrence Livermore National Laboratory (LLNL) and Electric Power Research Institute (EPRI) studies can be attributed to this choice. The LLNL study assumed a lower bound magnitude of 3.75 while the EPRI study assumed a lower bound magnitude of 5.0. The magnitudes used were assumed to be body wave magnitudes or their equivalents. In deterministic studies recent ground motion recordings of small to moderate earthquakes at or near nuclear power plants have shown that the high frequencies of design response spectra may be exceeded. These exceedances became important issues in the licensing of the Summer and Perry nuclear power plants. At various times in the past particular concerns have been raised with respect to the hazard and damage potential of small to moderate earthquakes occurring at very shallow depths. In this paper a closer look is taken at these issues. Emphasis is given to the impact of lower bound magnitude on probabilistic hazard calculations and the historical record of damage from small to moderate earthquakes. Limited recommendations are made as to how these issues should be viewed

Hazard assessment and risk management of offshore production chemicals

International Nuclear Information System (INIS)

Schobben, H.P.M.; Scholten, M.C.T.; Vik, E.A.; Bakke, S.

1994-01-01

There is a clear need for harmonization of the regulations with regard to the use and discharge of drilling and production chemicals in the North Sea. Therefore the CHARM (Chemical Hazard Assessment and Risk Management) model was developed. Both government (of several countries) and industry (E and P and chemical suppliers) participated in the project. The CHARM model is discussed and accepted by OSPARCON. The CHARM model consists of several modules. The model starts with a prescreening on the basis of hazardous properties like persistency, accumulation potential and the appearance on black lists. The core of the model.consists of modules for hazard assessment and risk analysis. Hazard assessment covers a general environmental evaluation of a chemical on the basis of intrinsic properties of that chemical. Risk analysis covers a more specific evaluation of the environmental impact from the use of a production chemical, or a combination of chemicals, under actual conditions. In the risk management module the user is guided to reduce the total risk of all chemicals used on a platform by the definition of measures in the most cost-effective way. The model calculates the environmental impact for the marine environment. Thereto three parts are distinguished: pelagic, benthic and food chain. Both hazard assessment and risk analysis are based on a proportional comparison of an estimated PEC with an estimated NEC. The PEC is estimated from the use, release, dilution and fate of the chemical and the NEC is estimated from the available toxicity data of the chemicals

Review of Natural Phenomena Hazard (NPH) Assessments for the DOE Hanford Site

Energy Technology Data Exchange (ETDEWEB)

Snow, Robert L.; Ross, Steven B.

2011-09-15

The purpose of this review is to assess the need for updating Natural Phenomena Hazard (NPH) assessments for the DOE's Hanford Site, as required by DOE Order 420.1B Chapter IV, Natural Phenomena Hazards Mitigation, based on significant changes in state-of-the-art NPH assessment methodology or site-specific information. This review is an update and expansion to the September 2010 review of PNNL-19751, Review of Natural Phenomena Hazard (NPH) Assessments for the Hanford 200 Areas (Non-Seismic).

Quantitative physical models of volcanic phenomena for hazards assessment of critical infrastructures

Science.gov (United States)

Costa, Antonio

2016-04-01

Volcanic hazards may have destructive effects on economy, transport, and natural environments at both local and regional scale. Hazardous phenomena include pyroclastic density currents, tephra fall, gas emissions, lava flows, debris flows and avalanches, and lahars. Volcanic hazards assessment is based on available information to characterize potential volcanic sources in the region of interest and to determine whether specific volcanic phenomena might reach a given site. Volcanic hazards assessment is focussed on estimating the distances that volcanic phenomena could travel from potential sources and their intensity at the considered site. Epistemic and aleatory uncertainties strongly affect the resulting hazards assessment. Within the context of critical infrastructures, volcanic eruptions are rare natural events that can create severe hazards. In addition to being rare events, evidence of many past volcanic eruptions is poorly preserved in the geologic record. The models used for describing the impact of volcanic phenomena generally represent a range of model complexities, from simplified physics based conceptual models to highly coupled thermo fluid dynamical approaches. Modelling approaches represent a hierarchy of complexity, which reflects increasing requirements for well characterized data in order to produce a broader range of output information. In selecting models for the hazard analysis related to a specific phenomenon, questions that need to be answered by the models must be carefully considered. Independently of the model, the final hazards assessment strongly depends on input derived from detailed volcanological investigations, such as mapping and stratigraphic correlations. For each phenomenon, an overview of currently available approaches for the evaluation of future hazards will be presented with the aim to provide a foundation for future work in developing an international consensus on volcanic hazards assessment methods.

Validation Of TRMM For Hazard Assessment In The Remote Context Of Tropical Africa

Science.gov (United States)

Monsieurs, E.; Kirschbaum, D.; Tan, J.; Jacobs, L.; Kervyn, M.; Demoulin, A.; Dewitte, O.

2017-12-01

Accurate rainfall data is fundamental for understanding and mitigating the disastrous effects of many rainfall-triggered hazards, especially when one considers the challenges arising from climate change and rainfall variability. In tropical Africa in particular, the sparse operational rainfall gauging network hampers the ability to understand these hazards. Satellite rainfall estimates (SRE) can therefore be of great value. Yet, rigorous validation is required to identify the uncertainties when using SRE for hazard applications. We evaluated the Tropical Rainfall Measuring Mission (TRMM) Multi-satellite Precipitation Analysis (TMPA) 3B42 Research Derived Daily Product from 1998 to 2017, at 0.25° x 0.25° spatial and 24 h temporal resolution. The validation was done over the western branch of the East African Rift, with the perspective of regional landslide hazard assessment in mind. Even though we collected an unprecedented dataset of 47 gauges with a minimum temporal resolution of 24 h, the sparse and heterogeneous temporal coverage in a region with high rainfall variability poses challenges for validation. In addition, the discrepancy between local-scale gauge data and spatially averaged ( 775 km²) TMPA data in the context of local convective storms and orographic rainfall is a crucial source of uncertainty. We adopted a flexible framework for SRE validation that fosters explorative research in a remote context. Results show that TMPA performs reasonably well during the rainy seasons for rainfall intensities controls on, and uncertainties of, TMPA revealed in this study. Moreover, it is found relevant in mapping regional-scale rainfall-triggered hazards that are in any case poorly covered by the sparse available gauges. We anticipate validation of TMPA's successor (Integrated Multi-satellitE Retrievals for Global Precipitation Measurement; 10 km × 10 km, half-hourly) using the proposed framework, as soon as this product will be available in early 2018 for the

Multi Hazard Assessment: The Azores Archipelagos (PT) case

Science.gov (United States)

Aifantopoulou, Dorothea; Boni, Giorgio; Cenci, Luca; Kaskara, Maria; Kontoes, Haris; Papoutsis, Ioannis; Paralikidis, Sideris; Psichogyiou, Christina; Solomos, Stavros; Squicciarino, Giuseppe; Tsouni, Alexia; Xerekakis, Themos

2016-04-01

The COPERNICUS EMS Risk & Recovery Mapping (RRM) activity offers services to support efficient design and implementation of mitigation measures and recovery planning based on EO data exploitation. The Azores Archipelagos case was realized in the context of the FWC 259811 Copernicus EMS RRM, and provides potential impact information for a number of natural disasters. The analysis identified population and assets at risk (infrastructures and environment). The risk assessment was based on hazard and vulnerability of structural elements, road network characteristics, etc. Integration of different hazards and risks was accounted in establishing the necessary first response/ first aid infrastructure. EO data (Pleiades and WV-2), were used to establish a detailed background information, common for the assessment of the whole of the risks. A qualitative Flood hazard level was established, through a "Flood Susceptibility Index" that accounts for upstream drainage area and local slope along the drainage network (Manfreda et al. 2014). Indicators, representing different vulnerability typologies, were accounted for. The risk was established through intersecting hazard and vulnerability (risk- specific lookup table). Probabilistic seismic hazards maps (PGA) were obtained by applying the Cornell (1968) methodology as implemented in CRISIS2007 (Ordaz et al. 2007). The approach relied on the identification of potential sources, the assessment of earthquake recurrence and magnitude distribution, the selection of ground motion model, and the mathematical model to calculate seismic hazard. Lava eruption areas and a volcanic activity related coefficient were established through available historical data. Lava flow paths and their convergence were estimated through applying a cellular, automata based, Lava Flow Hazard numerical model (Gestur Leó Gislason, 2013). The Landslide Hazard Index of NGI (Norwegian Geotechnical Institute) for heavy rainfall (100 year extreme monthly rainfall

Probabilistic Approaches for Multi-Hazard Risk Assessment of Structures and Systems

Science.gov (United States)

Kwag, Shinyoung

Performance assessment of structures, systems, and components for multi-hazard scenarios has received significant attention in recent years. However, the concept of multi-hazard analysis is quite broad in nature and the focus of existing literature varies across a wide range of problems. In some cases, such studies focus on hazards that either occur simultaneously or are closely correlated with each other. For example, seismically induced flooding or seismically induced fires. In other cases, multi-hazard studies relate to hazards that are not dependent or correlated but have strong likelihood of occurrence at different times during the lifetime of a structure. The current approaches for risk assessment need enhancement to account for multi-hazard risks. It must be able to account for uncertainty propagation in a systems-level analysis, consider correlation among events or failure modes, and allow integration of newly available information from continually evolving simulation models, experimental observations, and field measurements. This dissertation presents a detailed study that proposes enhancements by incorporating Bayesian networks and Bayesian updating within a performance-based probabilistic framework. The performance-based framework allows propagation of risk as well as uncertainties in the risk estimates within a systems analysis. Unlike conventional risk assessment techniques such as a fault-tree analysis, a Bayesian network can account for statistical dependencies and correlations among events/hazards. The proposed approach is extended to develop a risk-informed framework for quantitative validation and verification of high fidelity system-level simulation tools. Validation of such simulations can be quite formidable within the context of a multi-hazard risk assessment in nuclear power plants. The efficiency of this approach lies in identification of critical events, components, and systems that contribute to the overall risk. Validation of any event or

Multi scenario seismic hazard assessment for Egypt

Science.gov (United States)

Mostafa, Shaimaa Ismail; Abd el-aal, Abd el-aziz Khairy; El-Eraki, Mohamed Ahmed

2018-05-01

Egypt is located in the northeastern corner of Africa within a sensitive seismotectonic location. Earthquakes are concentrated along the active tectonic boundaries of African, Eurasian, and Arabian plates. The study area is characterized by northward increasing sediment thickness leading to more damage to structures in the north due to multiple reflections of seismic waves. Unfortunately, man-made constructions in Egypt were not designed to resist earthquake ground motions. So, it is important to evaluate the seismic hazard to reduce social and economic losses and preserve lives. The probabilistic seismic hazard assessment is used to evaluate the hazard using alternative seismotectonic models within a logic tree framework. Alternate seismotectonic models, magnitude-frequency relations, and various indigenous attenuation relationships were amended within a logic tree formulation to compute and develop the regional exposure on a set of hazard maps. Hazard contour maps are constructed for peak ground acceleration as well as 0.1-, 0.2-, 0.5-, 1-, and 2-s spectral periods for 100 and 475 years return periods for ground motion on rock. The results illustrate that Egypt is characterized by very low to high seismic activity grading from the west to the eastern part of the country. The uniform hazard spectra are estimated at some important cities distributed allover Egypt. The deaggregation of seismic hazard is estimated at some cities to identify the scenario events that contribute to a selected seismic hazard level. The results of this study can be used in seismic microzonation, risk mitigation, and earthquake engineering purposes.

Recent developments in the external hazard risk assessment in Ukraine

International Nuclear Information System (INIS)

2000-01-01

Ukrainian legislation prescribes safety analysis reports for all operating and future NPPs. Apart from main report they must include: safety analysis supplement; design basis accident analysis; beyond design basis accident analysis; probabilistic safety assessment (PSA); technical; substantiation of safety. Regulatory requirements to PSA contents cover the criteria for core damage frequency and large radioactive release frequency. Initiating events taken into account are internal events; internal hazards and external hazards. External hazards to be considered are seismic events, external fires, external floods, extreme ambient temperatures, aircraft crashes, etc. Current status of PSA development is related to operating WWER-440 and WWER-1000 NPPs and NPPs under construction. This presentation describes in detail the external hazard risk assessment for South Ukraine including methodology applied and expected future activities

Afghanistan Multi-Risk Assessment to Natural Hazards

Science.gov (United States)

Diermanse, Ferdinand; Daniell, James; Pollino, Maurizio; Glover, James; Bouwer, Laurens; de Bel, Mark; Schaefer, Andreas; Puglisi, Claudio; Winsemius, Hessel; Burzel, Andreas; Ammann, Walter; Aliparast, Mojtaba; Jongman, Brenden; Ranghieri, Federica; Fallesen, Ditte

2017-04-01

The geographical location of Afghanistan and years of environmental degradation in the country make Afghanistan highly prone to intense and recurring natural hazards such as flooding, earthquakes, snow avalanches, landslides, and droughts. These occur in addition to man-made disasters resulting in the frequent loss of live, livelihoods, and property. Since 1980, disasters caused by natural hazards have affected 9 million people and caused over 20,000 fatalities in Afghanistan. The creation, understanding and accessibility of hazard, exposure, vulnerability and risk information is key for effective management of disaster risk. This is especially true in Afghanistan, where reconstruction after recent natural disasters and military conflicts is on-going and will continue over the coming years. So far, there has been limited disaster risk information produced in Afghanistan, and information that does exist typically lacks standard methodology and does not have uniform geo-spatial coverage. There are currently no available risk assessment studies that cover all major natural hazards in Afghanistan, which can be used to assess the costs and benefits of different resilient reconstruction and disaster risk reduction strategies. As a result, the Government of Afghanistan has limited information regarding current and future disaster risk and the effectiveness of policy options on which to base their reconstruction and risk reduction decisions. To better understand natural hazard and disaster risk, the World Bank and Global Facility for Disaster Reduction and Recovery (GFDRR) are supporting the development of new fluvial flood, flash flood, drought, landslide, avalanche and seismic risk information in Afghanistan, as well as a first-order analysis of the costs and benefits of resilient reconstruction and risk reduction strategies undertaken by the authors. The hazard component is the combination of probability and magnitude of natural hazards. Hazard analyses were carried out

Assessment of mixed hazardous and radioactive waste sites at Hanford

International Nuclear Information System (INIS)

McLaughlin, T.J.; Cramer, K.H.; Lamar, D.A.; Sherwood, D.R.; Stenner, R.D.; Schulze, W.B.

1987-10-01

The US Department of Energy and Pacific Northwest Laboratory recently completed a preliminary assessment of 685 inactive hazardous waste sites located on the Hanford Site. The preliminary assessment involved collecting historical data and individual site information, conducting site inspections, and establishing an environmental impact priority, using the Hazard Ranking System, for each of these 685 sites. This preliminary assessment was the first step in the remediation process required by the Comprehensive Environmental Response, Compensation and Liability Act. This paper presents the results of that preliminary assessment. 10 refs., 4 figs., 1 tab

National-Level Multi-Hazard Risk Assessments in Sub-Saharan Africa

Science.gov (United States)

Murnane, R. J.; Balog, S.; Fraser, S. A.; Jongman, B.; Van Ledden, M.; Phillips, E.; Simpson, A.

2017-12-01

National-level risk assessments can provide important baseline information for decision-making on risk management and risk financing strategies. In this study, multi-hazard risk assessments were undertaken for 9 countries in Sub-Saharan Africa: Cape Verde, Ethiopia, Kenya, Niger, Malawi, Mali, Mozambique, Senegal and Uganda. The assessment was part of the Building Disaster Resilience in Sub-Saharan Africa Program and aimed at supporting the development of multi-risk financing strategies to help African countries make informed decisions to mitigate the socio-economic, fiscal and financial impacts of disasters. The assessments considered hazards and exposures consistent with the years 2010 and 2050. We worked with multiple firms to develop the hazard, exposure and vulnerability data and the risk results. The hazards include: coastal flood, drought, earthquake, landslide, riverine flood, tropical cyclone wind and storm surge, and volcanoes. For hazards expected to vary with climate, the 2050 hazard is based on the IPCC RCP 6.0. Geolocated exposure data for 2010 and 2050 at a 15 arc second ( 0.5 km) resolution includes: structures as a function of seven development patterns; transportation networks including roads, bridges, tunnels and rail; critical facilities such as schools, hospitals, energy facilities and government buildings; crops; population; and, gross domestic product (GDP). The 2050 exposure values for population are based on the IPCC SSP 2. Values for other exposure data are a function of population change. Vulnerability was based on openly available vulnerability functions. Losses were based on replacement values (e.g., cost/m2 or cost/km). Risk results are provided in terms of annual average loss and a variety of return periods at the national and Admin 1 levels. Assessments of recent historical events are used to validate the model results. In the future, it would be useful to use hazard footprints of historical events for validation purposes. The

Application of the Coastal Hazard Wheel methodology for coastal multi-hazard assessment and management in the state of Djibouti

DEFF Research Database (Denmark)

Appelquist, Lars Rosendahl; Balstrøm, Thomas

2014-01-01

coastal classification system that incorporates the main static and dynamic parameters determining the characteristics of a coastal environment. The methodology provides information on the hazards of ecosystem disruption, gradual inundation, salt water intrusion, erosion and flooding and can be used...... to support management decisions at local, regional and national level, in areas with limited access to geophysical data. The assessment for Djibouti applies a geographic information system (GIS) to develop a range of national hazard maps along with relevant hazard statistics and is showcasing the procedure......This paper presents the application of a new methodology for coastal multi-hazard assessment and management in a changing global climate on the state of Djibouti. The methodology termed the Coastal Hazard Wheel (CHW) is developed for worldwide application and is based on a specially designed...

Bayesian network learning for natural hazard assessments

Science.gov (United States)

Vogel, Kristin

2016-04-01

Even though quite different in occurrence and consequences, from a modelling perspective many natural hazards share similar properties and challenges. Their complex nature as well as lacking knowledge about their driving forces and potential effects make their analysis demanding. On top of the uncertainty about the modelling framework, inaccurate or incomplete event observations and the intrinsic randomness of the natural phenomenon add up to different interacting layers of uncertainty, which require a careful handling. Thus, for reliable natural hazard assessments it is crucial not only to capture and quantify involved uncertainties, but also to express and communicate uncertainties in an intuitive way. Decision-makers, who often find it difficult to deal with uncertainties, might otherwise return to familiar (mostly deterministic) proceedings. In the scope of the DFG research training group „NatRiskChange" we apply the probabilistic framework of Bayesian networks for diverse natural hazard and vulnerability studies. The great potential of Bayesian networks was already shown in previous natural hazard assessments. Treating each model component as random variable, Bayesian networks aim at capturing the joint distribution of all considered variables. Hence, each conditional distribution of interest (e.g. the effect of precautionary measures on damage reduction) can be inferred. The (in-)dependencies between the considered variables can be learned purely data driven or be given by experts. Even a combination of both is possible. By translating the (in-)dependences into a graph structure, Bayesian networks provide direct insights into the workings of the system and allow to learn about the underlying processes. Besides numerous studies on the topic, learning Bayesian networks from real-world data remains challenging. In previous studies, e.g. on earthquake induced ground motion and flood damage assessments, we tackled the problems arising with continuous variables

Harmonizing seismic hazard assessments for nuclear power plants

International Nuclear Information System (INIS)

Mallard, D.J.

1993-01-01

Even a cursory comparison between maps of global seismicity and NPP earthquake design levels reveals many inconsistencies. While, in part, this situation reflects the evolution in understanding of seismic hazards, mismatches can also be due to ongoing differences in the way the hazards are assessed and in local regulatory requirements. So far, formal international consensus has only been able to encompass broad principles, such as those recently recommended by the International Atomic Energy Agency, and even these can raise many technical issues, particularly relating to zones of diffuse seismicity. In the future, greater harmonisation in hazard assessments and, to some extent, in earthquake design levels could emerge through the more widespread use of probabilistic methods. International collaborative ventures and joint projects will be important for resolving anomalies in the existing databases and their interpretations, and for acquiring new data, but to achieve their ideal objectives, they will need to proceed in clearly defined stages. (author)

Y-12 National Security Complex Emergency Management Hazards Assessment (EMHA) Process; FINAL

International Nuclear Information System (INIS)

Bailiff, E.F.; Bolling, J.D.

2001-01-01

This document establishes requirements and standard methods for the development and maintenance of the Emergency Management Hazards Assessment (EMHA) process used by the lead and all event contractors at the Y-12 Complex for emergency planning and preparedness. The EMHA process provides the technical basis for the Y-12 emergency management program. The instructions provided in this document include methods and requirements for performing the following emergency management activities at Y-12: (1) hazards identification; (2) hazards survey, and (3) hazards assessment

Geomorphological hazards and environmental impact: Assessment and mapping

Science.gov (United States)

Panizza, Mario

In five sections the author develops the methods for the integration of geomorphological concepts into Environmental Impact and Mapping. The first section introduces the concepts of Impact and Risk through the relationships between Geomorphological Environment and Anthropical Element. The second section proposes a methodology for the determination of Geomorphological Hazard and the identification of Geomorphological Risk. The third section synthesizes the procedure for the compilation of a Geomorphological Hazards Map. The fourth section outlines the concepts of Geomorphological Resource Assessment for the analysis of the Environmental Impact. The fifth section considers the contribution of geomorphological studies and mapping in the procedure for Environmental Impact Assessment.

Assessment and classification of hazardous street trees in University ...

African Journals Online (AJOL)

The study was carried out to assessed and classified hazardous trees within the University of Ibadan (UI) campus, Oyo State, Nigeria. The study population was 25 municipal tree species comprising of 420 individual trees located along the major roads of the study area, which were considered hazardous to the community.

Hanford B Reactor Building Hazard Assessment Report

International Nuclear Information System (INIS)

Griffin, P. W.

1999-01-01

The 105-B Reactor (hereinafter referred to as B Reactor) is located in the 100 Area of the Hanford Site near Richland, Washington. The B Reactor is one of nine plutonium production reactors that were constructed in the 1940s during the Cold War Era. Construction of the B Reactor began June 7, 1943, and operation began on September 26, 1944. The Environmental Restoration Contractor was requested by RL to provide an assessment/characterization of the B Reactor building to determine and document the hazards that are present and could pose a threat to the environment and/or to individuals touring the building. This report documents the potential hazards, determines the feasibility of mitigating the hazards, and makes recommendations regarding areas where public tour access should not be permitted

Analysis and Assessment of Parameters Shaping Methane Hazard in Longwall Areas

Directory of Open Access Journals (Sweden)

Eugeniusz Krause

2013-01-01

Full Text Available Increasing coal production concentration and mining in coal seams of high methane content contribute to its growing emission to longwall areas. In this paper, analysis of survey data concerning the assessment of parameters that influence the level of methane hazard in mining areas is presented. The survey was conducted with experts on ventilation and methane hazard in coal mines. The parameters which influence methane hazard in longwall areas were assigned specific weights (numerical values. The summary will show which of the assessed parameters have a strong, or weak, influence on methane hazard in longwall areas close to coal seams of high methane content.

Assessment of volcanic hazards, vulnerability, risk and uncertainty (Invited)

Science.gov (United States)

Sparks, R. S.

2009-12-01

A volcanic hazard is any phenomenon that threatens communities . These hazards include volcanic events like pyroclastic flows, explosions, ash fall and lavas, and secondary effects such as lahars and landslides. Volcanic hazards are described by the physical characteristics of the phenomena, by the assessment of the areas that they are likely to affect and by the magnitude-dependent return period of events. Volcanic hazard maps are generated by mapping past volcanic events and by modelling the hazardous processes. Both these methods have their strengths and limitations and a robust map should use both approaches in combination. Past records, studied through stratigraphy, the distribution of deposits and age dating, are typically incomplete and may be biased. Very significant volcanic hazards, such as surge clouds and volcanic blasts, are not well-preserved in the geological record for example. Models of volcanic processes are very useful to help identify hazardous areas that do not have any geological evidence. They are, however, limited by simplifications and incomplete understanding of the physics. Many practical volcanic hazards mapping tools are also very empirical. Hazards maps are typically abstracted into hazards zones maps, which are some times called threat or risk maps. Their aim is to identify areas at high levels of threat and the boundaries between zones may take account of other factors such as roads, escape routes during evacuation, infrastructure. These boundaries may change with time due to new knowledge on the hazards or changes in volcanic activity levels. Alternatively they may remain static but implications of the zones may change as volcanic activity changes. Zone maps are used for planning purposes and for management of volcanic crises. Volcanic hazards maps are depictions of the likelihood of future volcanic phenomena affecting places and people. Volcanic phenomena are naturally variable, often complex and not fully understood. There are

Sandia Administrative Micrographics Facility, Building 802: Hazards assessment document

International Nuclear Information System (INIS)

Swihart, A.

1994-12-01

The Department of Energy Order 5500.3A requires facility-specific hazards assessments be prepared, maintained, and used for emergency planning purposes. This hazards assessment document describes the chemical and radiological hazards associated with the Sandia Administrative Micrographics Facility, Building 802. The entire inventory was screened according to the potential airborne impact to onsite and offsite individuals. The air dispersion model, ALOHA, estimated pollutant concentrations downwind from the source of a release, taking into consideration the toxicological and physical characteristics of the release site, the atmospheric conditions, and the circumstances of the release. The greatest distance at which a postulated facility event will produce consequences exceeding the Early Severe Health Effects threshold is 33 meters. The highest emergency classification is a Site Area Emergency. The Emergency Planning Zone is 75 meters

THE METHOD OF ASSESSING ROCK BURSTING HAZARD IN MINING

Directory of Open Access Journals (Sweden)

Anna MANOWSKA

2015-04-01

Full Text Available The article discusses a concept of forecasting accident risk during longwall extraction in crump-risk conditions. In Polish mines rock burst hazard can be described as high compared to other mines around the world. It's related to increase of depth of longwall field operation, preparation works, including drilling of mine face pavements which leads to systematic deterioration of geological and mining conditions. Depletion of coal is also the reason why mines operate in high mining tremor risk conditions. Mines more and more often operate in decks, where there is large number of edges and remains of older decks. Rocks bursts still remain one of the most dangerous natural hazards and therefore are fundamental prob-lem and have the greatest impact on safety in mining industry. The proposed method for forecasting accidents and loss-es in people and goods can contribute to improvement of work organization methods and mine safety management system.

The assessment of tornado missile hazard to nuclear power plants

International Nuclear Information System (INIS)

Goodman, J.; Koch, J.E.

1983-01-01

Numerical methods and computer codes for assessing tornado missile hazards to nuclear power plants are developed. Due to the uncertainty and randomness of tornado and tornado-generated missiles' characteristics, the damage probability of targets has a highly spread distribution. The proposed method is useful for assessing the risk of not providing protection to some nonsafety-related targets whose failure can create a hazard to the safe operation of nuclear power plants

A global probabilistic tsunami hazard assessment from earthquake sources

Science.gov (United States)

Davies, Gareth; Griffin, Jonathan; Lovholt, Finn; Glimsdal, Sylfest; Harbitz, Carl; Thio, Hong Kie; Lorito, Stefano; Basili, Roberto; Selva, Jacopo; Geist, Eric L.; Baptista, Maria Ana

2017-01-01

Large tsunamis occur infrequently but have the capacity to cause enormous numbers of casualties, damage to the built environment and critical infrastructure, and economic losses. A sound understanding of tsunami hazard is required to underpin management of these risks, and while tsunami hazard assessments are typically conducted at regional or local scales, globally consistent assessments are required to support international disaster risk reduction efforts, and can serve as a reference for local and regional studies. This study presents a global-scale probabilistic tsunami hazard assessment (PTHA), extending previous global-scale assessments based largely on scenario analysis. Only earthquake sources are considered, as they represent about 80% of the recorded damaging tsunami events. Globally extensive estimates of tsunami run-up height are derived at various exceedance rates, and the associated uncertainties are quantified. Epistemic uncertainties in the exceedance rates of large earthquakes often lead to large uncertainties in tsunami run-up. Deviations between modelled tsunami run-up and event observations are quantified, and found to be larger than suggested in previous studies. Accounting for these deviations in PTHA is important, as it leads to a pronounced increase in predicted tsunami run-up for a given exceedance rate.

Probabilistic Seismic Hazard Assessment for Iraq

Energy Technology Data Exchange (ETDEWEB)

Onur, Tuna [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Gok, Rengin [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Abdulnaby, Wathiq [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Shakir, Ammar M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Mahdi, Hanan [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Numan, Nazar M.S. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Al-Shukri, Haydar [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Chlaib, Hussein K. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Ameen, Taher H. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Abd, Najah A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2016-05-06

Probabilistic Seismic Hazard Assessments (PSHA) form the basis for most contemporary seismic provisions in building codes around the world. The current building code of Iraq was published in 1997. An update to this edition is in the process of being released. However, there are no national PSHA studies in Iraq for the new building code to refer to for seismic loading in terms of spectral accelerations. As an interim solution, the new draft building code was considering to refer to PSHA results produced in the late 1990s as part of the Global Seismic Hazard Assessment Program (GSHAP; Giardini et al., 1999). However these results are: a) more than 15 years outdated, b) PGA-based only, necessitating rough conversion factors to calculate spectral accelerations at 0.3s and 1.0s for seismic design, and c) at a probability level of 10% chance of exceedance in 50 years, not the 2% that the building code requires. Hence there is a pressing need for a new, updated PSHA for Iraq.

Long-term volcanic hazard assessment on El Hierro (Canary Islands)

Science.gov (United States)

Becerril, L.; Bartolini, S.; Sobradelo, R.; Martí, J.; Morales, J. M.; Galindo, I.

2014-07-01

Long-term hazard assessment, one of the bastions of risk-mitigation programs, is required for land-use planning and for developing emergency plans. To ensure quality and representative results, long-term volcanic hazard assessment requires several sequential steps to be completed, which include the compilation of geological and volcanological information, the characterisation of past eruptions, spatial and temporal probabilistic studies, and the simulation of different eruptive scenarios. Despite being a densely populated active volcanic region that receives millions of visitors per year, no systematic hazard assessment has ever been conducted on the Canary Islands. In this paper we focus our attention on El Hierro, the youngest of the Canary Islands and the most recently affected by an eruption. We analyse the past eruptive activity to determine the spatial and temporal probability, and likely style of a future eruption on the island, i.e. the where, when and how. By studying the past eruptive behaviour of the island and assuming that future eruptive patterns will be similar, we aim to identify the most likely volcanic scenarios and corresponding hazards, which include lava flows, pyroclastic fallout and pyroclastic density currents (PDCs). Finally, we estimate their probability of occurrence. The end result, through the combination of the most probable scenarios (lava flows, pyroclastic density currents and ashfall), is the first qualitative integrated volcanic hazard map of the island.

Assessing qualitative long-term volcanic hazards at Lanzarote Island (Canary Islands)

Science.gov (United States)

Becerril, Laura; Martí, Joan; Bartolini, Stefania; Geyer, Adelina

2017-07-01

Conducting long-term hazard assessment in active volcanic areas is of primary importance for land-use planning and defining emergency plans able to be applied in case of a crisis. A definition of scenario hazard maps helps to mitigate the consequences of future eruptions by anticipating the events that may occur. Lanzarote is an active volcanic island that has hosted the largest (> 1.5 km3 DRE) and longest (6 years) eruption, the Timanfaya eruption (1730-1736), on the Canary Islands in historical times (last 600 years). This eruption brought severe economic losses and forced local people to migrate. In spite of all these facts, no comprehensive hazard assessment or hazard maps have been developed for the island. In this work, we present an integrated long-term volcanic hazard evaluation using a systematic methodology that includes spatial analysis and simulations of the most probable eruptive scenarios.

The potential role of earthworms in toxicity assessment of terrestrial hazardous waste sites

Energy Technology Data Exchange (ETDEWEB)

Goven, A.J.; Fitzpatrick, L.C. [Univ. of North Texas, Denton, TX (United States); Venables, B.J. [TRAC Labs., Inc., Denton, TX (United States)

1994-12-31

Understanding the toxic potential and mechanisms of action of environmental xenobiotics is fundamental for assessing risk to public and environmental health. Current established protocols with earthworms focus primarily on defining the lethal effects of chemicals associated with soil contamination. Development of sublethal assays, until recently, has been largely ignored. Here the authors develop rationale for use of earthworms as a model organism for comprehensive assessment of risks to higher wildlife from contaminated soils and hazardous waste sites. They present a panel of lethal (LC/LD50`s) and sublethal measurement endpoint biomarkers, developed within the framework of the National Toxicology Program`s tiered immunotoxicity protocol for mice and according to published criteria for good measurement endpoints, that represent sensitive phylogenetically-conserved processes. Specifically the authors discuss immunosuppressive effects of terrestrial heavy metal and organic contamination on the innate, nonspecific and specific immune responses of earthworm, Lumbricus terrestris, coelomocytes in terms of total and differential cell counts, lysozyme activity, nitroblue tetrazolium dye reduction, phagocytic activity and secretary rosette formation. Findings indicate that sensitive phylogenetically conserved immune responses present in invertebrates can be used to assess or predict risk to wildlife from contaminated soils.

Modelling human interactions in the assessment of man-made hazards

International Nuclear Information System (INIS)

Nitoi, M.; Farcasiu, M.; Apostol, M.

2016-01-01

The human reliability assessment tools are not currently capable to model adequately the human ability to adapt, to innovate and to manage under extreme situations. The paper presents the results obtained by ICN PSA team in the frame of FP7 Advanced Safety Assessment Methodologies: extended PSA (ASAMPSA_E) project regarding the investigation of conducting HRA in human-made hazards. The paper proposes to use a 4-steps methodology for the assessment of human interactions in the external events (Definition and modelling of human interactions; Quantification of human failure events; Recovery analysis; Review). The most relevant factors with respect to HRA for man-made hazards (response execution complexity; existence of procedures with respect to the scenario in question; time available for action; timing of cues; accessibility of equipment; harsh environmental conditions) are presented and discussed thoroughly. The challenges identified in relation to man-made hazards HRA are highlighted. (authors)

A critical analysis of hazard resilience measures within sustainability assessment frameworks

International Nuclear Information System (INIS)

Matthews, Elizabeth C.; Sattler, Meredith; Friedland, Carol J.

2014-01-01

Today, numerous sustainability assessment frameworks (SAFs) exist to guide designers in achieving sustainable performance in the design of structures and communities. SAFs are beneficial in educating users and are useful tools for incorporating sustainability strategies into planning, design, and construction; however, there is currently a substantial gap in the ability of existing SAFs to incorporate hazard resistance and hazard mitigation in the broader context of sustainable design. This paper analyzes the incorporation of hazard resistant design and hazard mitigation strategies within SAFs via a multi-level analysis of eleven SAFs. The SAFs analyzed range in scale of application (i.e. building, site, community). Three levels of analysis are presented: (1) macro-level analysis comparing the number of measures strictly addressing resilience versus sustainability, (2) meso-level analysis of the coverage of types of hazards within SAFs (e.g. flood, fire), and (3) micro-level analysis of SAF measures connected to flood-related hazard resilience. The results demonstrate that hazard resistance and hazard mitigation do not figure prominently in the intent of SAFs and that weaknesses in resilience coverage exist that have the potential to lead to the design of structures and communities that are still highly vulnerable to the impacts of extreme events. - Highlights: • Sustainability assessment frameworks (SAFs) were analyzed for resilience coverage • Hazard resistance and mitigation do not figure prominently in the intent of SAFs • Approximately 75% of SAFs analyzed address three or fewer hazards • Lack of economic measures within SAFs could impact resilience and sustainability • Resilience measures for flood hazards are not consistently included in SAFs

A critical analysis of hazard resilience measures within sustainability assessment frameworks

Energy Technology Data Exchange (ETDEWEB)

Matthews, Elizabeth C., E-mail: echiso1@lsu.edu [Louisiana State University, Baton Rouge, LA (United States); Sattler, Meredith, E-mail: msattler@lsu.edu [School of Architecture, Louisiana State University, Baton Rouge, LA (United States); Friedland, Carol J., E-mail: friedland@lsu.edu [Bert S. Turner Department of Construction Management, Louisiana State University, Baton Rouge, LA (United States)

2014-11-15

Today, numerous sustainability assessment frameworks (SAFs) exist to guide designers in achieving sustainable performance in the design of structures and communities. SAFs are beneficial in educating users and are useful tools for incorporating sustainability strategies into planning, design, and construction; however, there is currently a substantial gap in the ability of existing SAFs to incorporate hazard resistance and hazard mitigation in the broader context of sustainable design. This paper analyzes the incorporation of hazard resistant design and hazard mitigation strategies within SAFs via a multi-level analysis of eleven SAFs. The SAFs analyzed range in scale of application (i.e. building, site, community). Three levels of analysis are presented: (1) macro-level analysis comparing the number of measures strictly addressing resilience versus sustainability, (2) meso-level analysis of the coverage of types of hazards within SAFs (e.g. flood, fire), and (3) micro-level analysis of SAF measures connected to flood-related hazard resilience. The results demonstrate that hazard resistance and hazard mitigation do not figure prominently in the intent of SAFs and that weaknesses in resilience coverage exist that have the potential to lead to the design of structures and communities that are still highly vulnerable to the impacts of extreme events. - Highlights: • Sustainability assessment frameworks (SAFs) were analyzed for resilience coverage • Hazard resistance and mitigation do not figure prominently in the intent of SAFs • Approximately 75% of SAFs analyzed address three or fewer hazards • Lack of economic measures within SAFs could impact resilience and sustainability • Resilience measures for flood hazards are not consistently included in SAFs.

Seismic hazard assessment of the Province of Murcia (SE Spain): analysis of source contribution to hazard

Science.gov (United States)

García-Mayordomo, J.; Gaspar-Escribano, J. M.; Benito, B.

2007-10-01

A probabilistic seismic hazard assessment of the Province of Murcia in terms of peak ground acceleration (PGA) and spectral accelerations [SA( T)] is presented in this paper. In contrast to most of the previous studies in the region, which were performed for PGA making use of intensity-to-PGA relationships, hazard is here calculated in terms of magnitude and using European spectral ground-motion models. Moreover, we have considered the most important faults in the region as specific seismic sources, and also comprehensively reviewed the earthquake catalogue. Hazard calculations are performed following the Probabilistic Seismic Hazard Assessment (PSHA) methodology using a logic tree, which accounts for three different seismic source zonings and three different ground-motion models. Hazard maps in terms of PGA and SA(0.1, 0.2, 0.5, 1.0 and 2.0 s) and coefficient of variation (COV) for the 475-year return period are shown. Subsequent analysis is focused on three sites of the province, namely, the cities of Murcia, Lorca and Cartagena, which are important industrial and tourism centres. Results at these sites have been analysed to evaluate the influence of the different input options. The most important factor affecting the results is the choice of the attenuation relationship, whereas the influence of the selected seismic source zonings appears strongly site dependant. Finally, we have performed an analysis of source contribution to hazard at each of these cities to provide preliminary guidance in devising specific risk scenarios. We have found that local source zones control the hazard for PGA and SA( T ≤ 1.0 s), although contribution from specific fault sources and long-distance north Algerian sources becomes significant from SA(0.5 s) onwards.

Hazard assessment for small torrent catchments - lessons learned

Science.gov (United States)

Eisl, Julia; Huebl, Johannes

2013-04-01

The documentation of extreme events as a part of the integral risk management cycle is an important basis for the analysis and assessment of natural hazards. In July 2011 a flood event occurred in the Wölzer-valley in the province of Styria, Austria. For this event at the "Wölzerbach" a detailed event documentation was carried out, gathering data about rainfall, runoff and sediment transport as well as information on damaged objects, infrastructure or crops using various sources. The flood was triggered by heavy rainfalls in two tributaries of the Wölzer-river. Though a rain as well as a discharge gaging station exists for the Wölzer-river, the torrents affected by the high intensity rainfalls are ungaged. For these ungaged torrent catchments the common methods for hazard assessment were evaluated. The back-calculation of the rainfall event was done using a new approach for precipitation analysis. In torrent catchments especially small-scale and high-intensity rainfall events are mainly responsible for extreme events. Austria's weather surveillance radar is operated by the air traffic service "AustroControl". The usually available dataset is interpreted and shows divergences especially when it comes to high intensity rainfalls. For this study the raw data of the radar were requested and analysed. Further on the event was back-calculated with different rainfall-runoff models, hydraulic models and sediment transport models to obtain calibration parameters for future use in hazard assessment for this region. Since there are often problems with woody debris different scenarios were simulated. The calibrated and plausible results from the runoff models were used for the comparison with empirical approaches used in the practical sector. For the planning of mitigation measures of the Schöttl-torrent, which is one of the affected tributaries of the Wölzer-river, a physical scale model was used in addition to the insights of the event analysis to design a check dam

Quantitative rock-fall hazard and risk assessment for Yosemite Valley, California

Science.gov (United States)

Stock, G. M.; Luco, N.; Collins, B. D.; Harp, E.; Reichenbach, P.; Frankel, K. L.

2011-12-01

Rock falls are a considerable hazard in Yosemite Valley, California with more than 835 rock falls and other slope movements documented since 1857. Thus, rock falls pose potentially significant risk to the nearly four million annual visitors to Yosemite National Park. Building on earlier hazard assessment work by the U.S. Geological Survey, we performed a quantitative rock-fall hazard and risk assessment for Yosemite Valley. This work was aided by several new data sets, including precise Geographic Information System (GIS) maps of rock-fall deposits, airborne and terrestrial LiDAR-based point cloud data and digital elevation models, and numerical ages of talus deposits. Using Global Position Systems (GPS), we mapped the positions of over 500 boulders on the valley floor and measured their distance relative to the mapped base of talus. Statistical analyses of these data yielded an initial hazard zone that is based on the 90th percentile distance of rock-fall boulders beyond the talus edge. This distance was subsequently scaled (either inward or outward from the 90th percentile line) based on rock-fall frequency information derived from a combination of cosmogenic beryllium-10 exposure dating of boulders beyond the edge of the talus, and computer model simulations of rock-fall runout. The scaled distances provide the basis for a new hazard zone on the floor of Yosemite Valley. Once this zone was delineated, we assembled visitor, employee, and resident use data for each structure within the hazard zone to quantitatively assess risk exposure. Our results identify areas within the new hazard zone that may warrant more detailed study, for example rock-fall susceptibility, which can be assessed through examination of high-resolution photographs, structural measurements on the cliffs, and empirical calculations derived from LiDAR point cloud data. This hazard and risk information is used to inform placement of existing and potential future infrastructure in Yosemite Valley.

Health Risk Assessment on Hazardous Ingredients in Household Deodorizing Products

Directory of Open Access Journals (Sweden)

Minjin Lee

2018-04-01

Full Text Available The inhalation of a water aerosol from a humidifier containing disinfectants has led to serious lung injuries in Korea. To promote the safe use of products, the Korean government enacted regulations on the chemicals in various consumer products that could have adverse health effects. Given the concern over the potential health risks associated with the hazardous ingredients in deodorizing consumer products, 17 ingredients were analyzed and assessed according to their health risk on 3 groups by the application type in 47 deodorizing products. The risk assessment study followed a stepwise procedure (e.g., collecting toxicological information, hazard identification/exposure assessment, and screening and detailed assessment for inhalation and dermal routes. The worst-case scenario and maximum concentration determined by the product purpose and application type were used as the screening assessment. In a detailed assessment, the 75th exposure factor values were used to estimate the assumed reasonable exposure to ingredients. The exposed concentrations of seven ingredients were calculated. Due to limitation of toxicity information, butylated hydroxyl toluene for a consumer’s exposure via the dermal route only was conducted for a detailed assessment. This study showed that the assessed ingredients have no health risks at their maximum concentrations in deodorizing products. This approach can be used to establish guidelines for ingredients that may pose inhalation and dermal hazards.

Health Risk Assessment on Hazardous Ingredients in Household Deodorizing Products

Science.gov (United States)

Lee, Minjin; Kim, Joo-Hyon; Lee, Daeyeop; Kim, Jaewoo; Lim, Hyunwoo; Seo, Jungkwan; Park, Young-Kwon

2018-01-01

The inhalation of a water aerosol from a humidifier containing disinfectants has led to serious lung injuries in Korea. To promote the safe use of products, the Korean government enacted regulations on the chemicals in various consumer products that could have adverse health effects. Given the concern over the potential health risks associated with the hazardous ingredients in deodorizing consumer products, 17 ingredients were analyzed and assessed according to their health risk on 3 groups by the application type in 47 deodorizing products. The risk assessment study followed a stepwise procedure (e.g., collecting toxicological information, hazard identification/exposure assessment, and screening and detailed assessment for inhalation and dermal routes). The worst-case scenario and maximum concentration determined by the product purpose and application type were used as the screening assessment. In a detailed assessment, the 75th exposure factor values were used to estimate the assumed reasonable exposure to ingredients. The exposed concentrations of seven ingredients were calculated. Due to limitation of toxicity information, butylated hydroxyl toluene for a consumer’s exposure via the dermal route only was conducted for a detailed assessment. This study showed that the assessed ingredients have no health risks at their maximum concentrations in deodorizing products. This approach can be used to establish guidelines for ingredients that may pose inhalation and dermal hazards. PMID:29652814

Assessing qualitative long-term volcanic hazards at Lanzarote Island (Canary Islands

Directory of Open Access Journals (Sweden)

L. Becerril

2017-07-01

Full Text Available Conducting long-term hazard assessment in active volcanic areas is of primary importance for land-use planning and defining emergency plans able to be applied in case of a crisis. A definition of scenario hazard maps helps to mitigate the consequences of future eruptions by anticipating the events that may occur. Lanzarote is an active volcanic island that has hosted the largest (>  1.5 km3 DRE and longest (6 years eruption, the Timanfaya eruption (1730–1736, on the Canary Islands in historical times (last 600 years. This eruption brought severe economic losses and forced local people to migrate. In spite of all these facts, no comprehensive hazard assessment or hazard maps have been developed for the island. In this work, we present an integrated long-term volcanic hazard evaluation using a systematic methodology that includes spatial analysis and simulations of the most probable eruptive scenarios.

Comparative Distributions of Hazard Modeling Analysis

Directory of Open Access Journals (Sweden)

Rana Abdul Wajid

2006-07-01

Full Text Available In this paper we present the comparison among the distributions used in hazard analysis. Simulation technique has been used to study the behavior of hazard distribution modules. The fundamentals of Hazard issues are discussed using failure criteria. We present the flexibility of the hazard modeling distribution that approaches to different distributions.

Observational assessment of fundamental movement skill proficiency in preschool children

OpenAIRE

佐々木, 玲子; 石沢, 順子

2014-01-01

Fundamental movement skill competency in children has been declining in recent years. Early childhood is a sensitive period for the development of fundamental movement skills ; the mastery of certain of these skills is a prerequisite for daily functioning and participation in later physical or sport-specific activities. Although quantitative methods have been developed for assessing movement development in children, it is also important to qualitatively evaluate such skills in developing chil...

Elevation uncertainty in coastal inundation hazard assessments

Science.gov (United States)

Gesch, Dean B.; Cheval, Sorin

2012-01-01

Coastal inundation has been identified as an important natural hazard that affects densely populated and built-up areas (Subcommittee on Disaster Reduction, 2008). Inundation, or coastal flooding, can result from various physical processes, including storm surges, tsunamis, intense precipitation events, and extreme high tides. Such events cause quickly rising water levels. When rapidly rising water levels overwhelm flood defenses, especially in heavily populated areas, the potential of the hazard is realized and a natural disaster results. Two noteworthy recent examples of such natural disasters resulting from coastal inundation are the Hurricane Katrina storm surge in 2005 along the Gulf of Mexico coast in the United States, and the tsunami in northern Japan in 2011. Longer term, slowly varying processes such as land subsidence (Committee on Floodplain Mapping Technologies, 2007) and sea-level rise also can result in coastal inundation, although such conditions do not have the rapid water level rise associated with other flooding events. Geospatial data are a critical resource for conducting assessments of the potential impacts of coastal inundation, and geospatial representations of the topography in the form of elevation measurements are a primary source of information for identifying the natural and human components of the landscape that are at risk. Recently, the quantity and quality of elevation data available for the coastal zone have increased markedly, and this availability facilitates more detailed and comprehensive hazard impact assessments.

Seismic hazard assessment; Valutazione della pericolosita` sismica

Energy Technology Data Exchange (ETDEWEB)

Paciello, A. [ENEA, Centro Ricerche Casaccia, Rome (Italy). Dip. Ambiente

1998-12-31

This paper presents a brief summary of the most commonly used methodologies for seismic hazard assessment. The interest is focused on the probabilistic approach, which can take into account the uncertainties of input data and provides results better comparable with those obtained from hazard analyses of other natural phenomena. Calculation methods, input data and treatment of variability are examined. Some examples of probabilistic seismic hazard maps are moreover presented. [Italiano] Questo lavoro presenta un breve sommario delle piu` comuni metodologie utilizzate per la valutazione della pericolosita` sismica di un sito. Una particolare attenzione e` rivolta all`approccio probabilistico, che permette di tener conto delle incertezze legate ai dati iniziali e fornisce risultati piu` facilmente confrontabili con quelli ottenuti da analisi di pericolosita` di altri fenomeni naturali. Vengono presi in esame i metodi di calcolo, i dati di base e il trattamento delle incertezze. Vengono inoltre presentati alcuni esempi di carte di pericolosita` sismica di tipo probabilistico.

A spatiotemporal multi-hazard exposure assessment based on property data

Science.gov (United States)

Fuchs, Sven; Keiler, Margreth; Zischg, Andreas

2016-04-01

The paper presents a nation-wide spatially explicit object-based assessment of buildings and citizens exposed to natural hazards in Austria, including river flooding, torrential flooding, and snow avalanches. The assessment was based on two different datasets, (a) hazard information providing input to the exposure of elements at risk, and (b) information on the building stock combined from different spatial data available on the national level. Hazard information was compiled from two different sources. For torrential flooding and snow avalanches available local-scale hazard maps were used, and for river flooding the results of the countrywide flood modelling eHORA were available. Information on the building stock contained information on the location and size of each building, as well as on the building category and the construction period. Additional information related to the individual floors, such as their height and net area, main purpose and configuration, was included for each property. Moreover, this dataset has an interface to the population register and allowed therefore retrieving the number of primary residents for each building. With the exception of sacral buildings, an economic module was used to compute the monetary value of buildings using (a) the information of the building register such as building type, number of storeys and utilisation, and (b) regionally averaged construction costs. It is shown that the repeatedly-stated assumption of increasing exposure due to continued population growth and related increase in assets has to be carefully evaluated by the local development of building stock. While some regions have shown a clearly above-average increase in assets, other regions were characterised by a below-average development. This mirrors the topography of the country, but also the different economic activities. While hotels and hostels are extraordinary prone to torrential flooding, commercial buildings as well as buildings used for

Comparison of landslide hazard and risk assessment practices in Europe

Science.gov (United States)

Corominas, J.; Mavrouli, O.

2012-04-01

An overview is made of the landslide hazard and risk assessment practices that are officially promoted or applied in Europe by administration offices, geological surveys, and decision makers (recommendations, regulations and codes). The reported countries are: Andorra, Austria, France, Italy (selected river basins), Romania, Spain (Catalonia), Switzerland and United Kingdom. The objective here was to compare the different practices for hazard and risk evaluation with respect to the official policies, the methodologies used (qualitative and quantitative), the provided outputs and their contents, and the terminology and map symbols used. The main observations made are illustrated with examples and the possibility of harmonization of the policies and the application of common practices to bridge the existing gaps is discussed. Some of the conclusions reached include the following: zoning maps are legally binding for public administrators and land owners only in some cases and generally when referring to site-specific or local scales rather than regional or national ones; so far, information is mainly provided on landslide susceptibility and hazard and risk assessment is performed only in a few countries; there is a variation in the use of scales between countries; the classification criteria for landslide types and mechanisms present large diversity even within the same country (in some cases no landslide mechanisms are specified while in others there is an exhaustive list); the techniques to obtain input data for the landslide inventory and susceptibility maps vary from basic to sophisticated, resulting in various levels of data quality and quantity; the procedures followed for hazard and risk assessment include analytical procedures supported by computer simulation, weighted-indicators, expert judgment and field survey-based, or a combination of all; there is an important variation between hazard and risk matrices with respect to the used parameters, the thresholds

Combining heuristic and statistical techniques in landslide hazard assessments

Science.gov (United States)

Cepeda, Jose; Schwendtner, Barbara; Quan, Byron; Nadim, Farrokh; Diaz, Manuel; Molina, Giovanni

2014-05-01

As a contribution to the Global Assessment Report 2013 - GAR2013, coordinated by the United Nations International Strategy for Disaster Reduction - UNISDR, a drill-down exercise for landslide hazard assessment was carried out by entering the results of both heuristic and statistical techniques into a new but simple combination rule. The data available for this evaluation included landslide inventories, both historical and event-based. In addition to the application of a heuristic method used in the previous editions of GAR, the availability of inventories motivated the use of statistical methods. The heuristic technique is largely based on the Mora & Vahrson method, which estimates hazard as the product of susceptibility and triggering factors, where classes are weighted based on expert judgment and experience. Two statistical methods were also applied: the landslide index method, which estimates weights of the classes for the susceptibility and triggering factors based on the evidence provided by the density of landslides in each class of the factors; and the weights of evidence method, which extends the previous technique to include both positive and negative evidence of landslide occurrence in the estimation of weights for the classes. One key aspect during the hazard evaluation was the decision on the methodology to be chosen for the final assessment. Instead of opting for a single methodology, it was decided to combine the results of the three implemented techniques using a combination rule based on a normalization of the results of each method. The hazard evaluation was performed for both earthquake- and rainfall-induced landslides. The country chosen for the drill-down exercise was El Salvador. The results indicate that highest hazard levels are concentrated along the central volcanic chain and at the centre of the northern mountains.

Assessment of vulnerability to storm induced flood hazard along diverse coastline settings

Directory of Open Access Journals (Sweden)

Valchev Nikolay

2016-01-01

Full Text Available European coasts suffer notably from hazards caused by low-probability and high-impact hydrometeorological events. The aim of the study is to assess in probabilistic terms the magnitude of storm‐induced flooding hazard along Varna regional coast (Bulgaria, western Black Sea and to identify susceptible coastal sectors (hotspots. The study is performed employing the Coastal Risk Assessment Framework (CRAF developed within EU FP7 RISC-KIT project. It constitutes a screening process that allows estimation of relevant hazard intensities, extents and potential receptors’ exposure vulnerability within predefined sectors. Total water level was the chief property considered for calculation of coastal flooding hazard. It was estimated using Holman model (for sandy beaches and EurOtop formulation (for artificial or rocky slopes. Resulting values were subjected to Extreme Value Analysis to establish that the best fitting distribution corresponds to Generalized Extreme Value distribution. Furthermore, hazard extents were modelled by means of bathtubbing or overwash estimation in order to form the flooding hazard indicator. Land use, social vulnerability, transport systems, utilities and business settings were considered as exposure indicators. Finally, potential risk was assessed by coastal indices following an index-based methodology, which combines hazard and exposure indicators into a single index, thereby providing base for comparison of coastal sectors’ vulnerability. The study found that the concentration of hotspots is highest in Varna Bay.

Hazard Assessment on Chlorine Distribution Use of Chemical Transportation Risk Index

International Nuclear Information System (INIS)

Kim, Jeong Gon; Byun, Hun Soo

2014-01-01

Chlorine is one of the most produced and most used non-flammable chemical substances in the world even though its toxicity and high reactivity cause the ozone layer depletion. However, in modern life, it is impossible to live a good life without using Chlorine and its derivatives since they are being used as an typical ingredient in more than 40 percent of the manufactured goods including medicines, detergents, deodorant, fungicides, herbicides, insecticides, and plastic, etc. Even if Chlorine has been handled and distributed in various business (small and medium-sized businesses, water purification plants, distribution company, etc.), there have been few researches about its possible health hazard and transportation risks. Accordingly, the purpose of this paper is to make a detailed assessment of Chlorinerelated risks and to model an index of chemicals transportation risks that is adequate for domestic circumstances. The assessment of possible health hazard and transportation risks was made on 13 kinds of hazardous chemicals, including liquid chlorine. This research may be contributed to standardizing the risk assessment of Chlorine and other hazardous chemicals by using an index of transportation risks

Hazard Assessment on Chlorine Distribution Use of Chemical Transportation Risk Index

Energy Technology Data Exchange (ETDEWEB)

Kim, Jeong Gon [Hanwha Chemical Ulsan Site, Ulsan (Korea, Republic of); Byun, Hun Soo [Chonnam National University, Yeosu (Korea, Republic of)

2014-12-15

Chlorine is one of the most produced and most used non-flammable chemical substances in the world even though its toxicity and high reactivity cause the ozone layer depletion. However, in modern life, it is impossible to live a good life without using Chlorine and its derivatives since they are being used as an typical ingredient in more than 40 percent of the manufactured goods including medicines, detergents, deodorant, fungicides, herbicides, insecticides, and plastic, etc. Even if Chlorine has been handled and distributed in various business (small and medium-sized businesses, water purification plants, distribution company, etc.), there have been few researches about its possible health hazard and transportation risks. Accordingly, the purpose of this paper is to make a detailed assessment of Chlorinerelated risks and to model an index of chemicals transportation risks that is adequate for domestic circumstances. The assessment of possible health hazard and transportation risks was made on 13 kinds of hazardous chemicals, including liquid chlorine. This research may be contributed to standardizing the risk assessment of Chlorine and other hazardous chemicals by using an index of transportation risks.

Long Aftershock Sequences within Continents and Implications for Earthquake Hazard Assessment

Science.gov (United States)

Stein, S. A.; Liu, M.

2014-12-01

Recent seismicity in the Tangshan region in North China has prompted concern about a repetition of the 1976 M7.8 earthquake that destroyed the city, killing more than 242,000 people. However, the decay of seismicity there implies that the recent earthquakes are probably aftershocks of the 1976 event. This 37-year sequence is an example of the phenomenon that aftershock sequences within continents are often significantly longer than the typical 10 years at plate boundaries. The long sequence of aftershocks in continents is consistent with a simple friction-based model predicting that the length of aftershock sequences varies inversely with the rate at which faults are loaded. Hence the slowly-deforming continents tend to have aftershock sequences significantly longer than at rapidly-loaded plate boundaries. This effect has two consequences for hazard assessment. First, within the heavily populated continents that are typically within plate interiors, assessments of earthquake hazards rely significantly on the assumption that the locations of small earthquakes shown by the short historical record reflect continuing deformation that will cause future large earthquakes. This assumption would lead to overestimation of the hazard in presently active areas and underestimation elsewhere, if some of these small events are aftershocks. Second, successful attempts to remove aftershocks from catalogs used for hazard assessment would underestimate the hazard, because much of the hazard is due to the aftershocks, and the declustering algorithms implicitly assume short aftershock sequences and thus do not remove long-duration ones.

Debris flows: behavior and hazard assessment

Science.gov (United States)

Iverson, Richard M.

2014-01-01

Debris flows are water-laden masses of soil and fragmented rock that rush down mountainsides, funnel into stream channels, entrain objects in their paths, and form lobate deposits when they spill onto valley floors. Because they have volumetric sediment concentrations that exceed 40 percent, maximum speeds that surpass 10 m/s, and sizes that can range up to ~109 m3, debris flows can denude slopes, bury floodplains, and devastate people and property. Computational models can accurately represent the physics of debris-flow initiation, motion and deposition by simulating evolution of flow mass and momentum while accounting for interactions of debris' solid and fluid constituents. The use of physically based models for hazard forecasting can be limited by imprecise knowledge of initial and boundary conditions and material properties, however. Therefore, empirical methods continue to play an important role in debris-flow hazard assessment.

Glass Formulation and Fabrication Laboratory, Building 864, Hazards assessment document

Energy Technology Data Exchange (ETDEWEB)

Banda, Z.; Wood, C.L.

1995-08-01

The Department of Energy Order 5500.3A requires facility-specific hazards assessments be prepared, maintained, and used for emergency planning purposes. This hazards assessment document describes the chemical and radiological hazards associated with the Glass Formulation and Fabrication Laboratory, Building 864. The entire inventory was screened according to the potential airborne impact to onsite and offsite individuals. The air dispersion model, ALOHA, estimated pollutant concentrations downwind from the source of a release, taking into consideration the toxicological and physical characteristics of the release site, the atmospheric conditions, and the circumstances of the release. The greatest distances at which a postulated facility event will produce consequences exceeding the ERPG-2 threshold is 96 meters. The highest emergency classification is a Site Area Emergency. The Emergency Planning Zone is 100 meters.

ASSESSING CHEMICAL HAZARDS AT THE PLUTONIUM FINISHING PLANT FOR PLANNING FUTURE DECONTAMINATION AND DECOMMISSIONING

International Nuclear Information System (INIS)

HOPKINS, A.M.; KLOS, D.B.; MINETT, M.J.

2007-01-01

This paper documents the fiscal year (FY) 2006 assessment to evaluate potential chemical and radiological hazards associated with vessels and piping in the former plutonium process areas at Hanford's Plutonium Finishing Plant (PFP). Evaluations by PFP engineers as design authorities for specific systems and other subject-matter experts were conducted to identify the chemical hazards associated with transitioning the process areas for the long-term layup of PFP before its eventual final decontamination and decommissioning (D and D). D and D activities in the main process facilities were suspended in September 2005 for a period of between 5 and 10 years. A previous assessment conducted in FY 2003 found that certain activities to mitigate chemical hazards could be deferred safely until the D and D of PFP, which had been scheduled to result in a slab-on-grade condition by 2009. As a result of necessary planning changes, however, D and D activities at PFP will be delayed until after the 2009 time frame. Given the extended project and plant life, it was determined that a review of the plant chemical hazards should be conducted. This review to determine the extended life impact of chemicals is called the ''Plutonium Finishing Plant Chemical Hazards Assessment, FY 2006''. This FY 2006 assessment addresses potential chemical and radiological hazard areas identified by facility personnel and subject-matter experts who reevaluated all the chemical systems (items) from the FY 2003 assessment. This paper provides the results of the FY 2006 chemical hazards assessment and describes the methodology used to assign a hazard ranking to the items reviewed

Probabilistic risk assessment framework for structural systems under multiple hazards using Bayesian statistics

Energy Technology Data Exchange (ETDEWEB)

Kwag, Shinyoung [North Carolina State University, Raleigh, NC 27695 (United States); Korea Atomic Energy Research Institute, Daejeon 305-353 (Korea, Republic of); Gupta, Abhinav, E-mail: agupta1@ncsu.edu [North Carolina State University, Raleigh, NC 27695 (United States)

2017-04-15

Highlights: • This study presents the development of Bayesian framework for probabilistic risk assessment (PRA) of structural systems under multiple hazards. • The concepts of Bayesian network and Bayesian inference are combined by mapping the traditionally used fault trees into a Bayesian network. • The proposed mapping allows for consideration of dependencies as well as correlations between events. • Incorporation of Bayesian inference permits a novel way for exploration of a scenario that is likely to result in a system level “vulnerability.” - Abstract: Conventional probabilistic risk assessment (PRA) methodologies (USNRC, 1983; IAEA, 1992; EPRI, 1994; Ellingwood, 2001) conduct risk assessment for different external hazards by considering each hazard separately and independent of each other. The risk metric for a specific hazard is evaluated by a convolution of the fragility and the hazard curves. The fragility curve for basic event is obtained by using empirical, experimental, and/or numerical simulation data for a particular hazard. Treating each hazard as an independently can be inappropriate in some cases as certain hazards are statistically correlated or dependent. Examples of such correlated events include but are not limited to flooding induced fire, seismically induced internal or external flooding, or even seismically induced fire. In the current practice, system level risk and consequence sequences are typically calculated using logic trees to express the causative relationship between events. In this paper, we present the results from a study on multi-hazard risk assessment that is conducted using a Bayesian network (BN) with Bayesian inference. The framework can consider statistical dependencies among risks from multiple hazards, allows updating by considering the newly available data/information at any level, and provide a novel way to explore alternative failure scenarios that may exist due to vulnerabilities.

Probabilistic risk assessment framework for structural systems under multiple hazards using Bayesian statistics

International Nuclear Information System (INIS)

Kwag, Shinyoung; Gupta, Abhinav

2017-01-01

Highlights: • This study presents the development of Bayesian framework for probabilistic risk assessment (PRA) of structural systems under multiple hazards. • The concepts of Bayesian network and Bayesian inference are combined by mapping the traditionally used fault trees into a Bayesian network. • The proposed mapping allows for consideration of dependencies as well as correlations between events. • Incorporation of Bayesian inference permits a novel way for exploration of a scenario that is likely to result in a system level “vulnerability.” - Abstract: Conventional probabilistic risk assessment (PRA) methodologies (USNRC, 1983; IAEA, 1992; EPRI, 1994; Ellingwood, 2001) conduct risk assessment for different external hazards by considering each hazard separately and independent of each other. The risk metric for a specific hazard is evaluated by a convolution of the fragility and the hazard curves. The fragility curve for basic event is obtained by using empirical, experimental, and/or numerical simulation data for a particular hazard. Treating each hazard as an independently can be inappropriate in some cases as certain hazards are statistically correlated or dependent. Examples of such correlated events include but are not limited to flooding induced fire, seismically induced internal or external flooding, or even seismically induced fire. In the current practice, system level risk and consequence sequences are typically calculated using logic trees to express the causative relationship between events. In this paper, we present the results from a study on multi-hazard risk assessment that is conducted using a Bayesian network (BN) with Bayesian inference. The framework can consider statistical dependencies among risks from multiple hazards, allows updating by considering the newly available data/information at any level, and provide a novel way to explore alternative failure scenarios that may exist due to vulnerabilities.

AECB workshop on seismic hazard assessment in southern Ontario

International Nuclear Information System (INIS)

Stepp, J.C.; Price, R.A.; Coppersmith, K.J.; Klimkiewicz, G.C.; McGuire, R.K.

1995-10-01

The purpose of the workshop was to review available geological and seismological data which could affect earthquake occurrence in southern Ontario and to develop a consensus on approaches that should be adopted for characterization of seismic hazard. The workshop was structured in technical sessions to focus presentations and discussions on four technical issues relevant to seismic hazard in southern Ontario, as follows: (1) The importance of geological and geophysical observations for the determination of seismic sources, (2) Methods and approaches which may be adopted for determining seismic sources based on integrated interpretations of geological and seismological information, (3) Methods and data which should be used for characterizing the seismicity parameters of seismic sources, and (4) Methods for assessment of vibratory ground motion hazard. The format of each session involved invited presentations of relevant data followed by open presentations by participants, a general discussion focusing on the relevance of the presented information for seismic hazard assessment in southern Ontario, then development of conclusions and recommendations. In the final session, the conclusions and recommendations were summarized and an open discussion was held to develop consensus. This report presents perspective summaries of the workshop technical sessions together with conclusions and recommendations prepared by the session chairs and the general chairman. 2 refs

Integration of Probabilistic Exposure Assessment and Probabilistic Hazard Characterization

NARCIS (Netherlands)

Voet, van der H.; Slob, W.

2007-01-01

A method is proposed for integrated probabilistic risk assessment where exposure assessment and hazard characterization are both included in a probabilistic way. The aim is to specify the probability that a random individual from a defined (sub)population will have an exposure high enough to cause a

Mine aftershocks and implications for seismic hazard assessment

CSIR Research Space (South Africa)

Kgarume, T

2010-11-01

Full Text Available A methodology of assessing the seismic hazard associated with aftershocks is developed by performing statistical and deterministic analysis of seismic data from two South African deep-level gold mines. A method employing stacking of aftershocks...

Multi-hazard assessment using GIS in the urban areas: Case study - Banja Luka municipality, B&H

Directory of Open Access Journals (Sweden)

Tošić Radislav

2013-01-01

Full Text Available The research presents a techniques for natural hazard assessment using GIS and cartographic approaches with multi-hazard mapping in urban communities, because natural hazards are a multi-dimensional phenomena which have a spatial component. Therefore the use of Remote Sensing and GIS has an important function and become essential in urban multi-hazard assessment. The first aim of this research was to determine the geographical distributions of the major types of natural hazards in the study area. Seismic hazards, landslides, rockfalls, floods, torrential floods, and excessive erosion are the most significant natural hazards within the territory of Banja Luka Municipality. Areas vulnerable to some of these natural hazards were singled out using analytical maps. Based on these analyses, an integral map of the natural hazards of the study area was created using multi-hazard assessment and the total vulnerability was determined by overlapping the results. The detailed analysis, through the focused research within the most vulnerable areas in the study area will highlight the administrative units (urban centres and communes that are vulnerable to various types of natural hazard. The results presented in this article are the first multi-hazard assessment and the first version of the integral map of natural hazards in the Republic of Srpska.

Hazard Identification and Risk Assessment in Water Treatment Plant considering Environmental Health and Safety Practice

Directory of Open Access Journals (Sweden)

Falakh Fajrul

2018-01-01

Full Text Available Water Treatment Plant (WTP is an important infrastructure to ensure human health and the environment. In its development, aspects of environmental safety and health are of concern. This paper case study was conducted at the Water Treatment Plant Company in Semarang, Central Java, Indonesia. Hazard identification and risk assessment is one part of the occupational safety and health program at the risk management stage. The purpose of this study was to identify potential hazards using hazard identification methods and risk assessment methods. Risk assessment is done using criteria of severity and probability of accident. The results obtained from this risk assessment are 22 potential hazards present in the water purification process. Extreme categories that exist in the risk assessment are leakage of chlorine and industrial fires. Chlorine and fire leakage gets the highest value because its impact threatens many things, such as industrial disasters that could endanger human life and the environment. Control measures undertaken to avoid potential hazards are to apply the use of personal protective equipment, but management will also be better managed in accordance with hazard control hazards, occupational safety and health programs such as issuing work permits, emergency response training is required, Very useful in overcoming potential hazards that have been determined.

Hazard Identification and Risk Assessment in Water Treatment Plant considering Environmental Health and Safety Practice

Science.gov (United States)

Falakh, Fajrul; Setiani, Onny

2018-02-01

Water Treatment Plant (WTP) is an important infrastructure to ensure human health and the environment. In its development, aspects of environmental safety and health are of concern. This paper case study was conducted at the Water Treatment Plant Company in Semarang, Central Java, Indonesia. Hazard identification and risk assessment is one part of the occupational safety and health program at the risk management stage. The purpose of this study was to identify potential hazards using hazard identification methods and risk assessment methods. Risk assessment is done using criteria of severity and probability of accident. The results obtained from this risk assessment are 22 potential hazards present in the water purification process. Extreme categories that exist in the risk assessment are leakage of chlorine and industrial fires. Chlorine and fire leakage gets the highest value because its impact threatens many things, such as industrial disasters that could endanger human life and the environment. Control measures undertaken to avoid potential hazards are to apply the use of personal protective equipment, but management will also be better managed in accordance with hazard control hazards, occupational safety and health programs such as issuing work permits, emergency response training is required, Very useful in overcoming potential hazards that have been determined.

Seismic Hazard Assessment at Esfaraen‒Bojnurd Railway, North‒East of Iran

Science.gov (United States)

Haerifard, S.; Jarahi, H.; Pourkermani, M.; Almasian, M.

2018-01-01

The objective of this study is to evaluate the seismic hazard at the Esfarayen-Bojnurd railway using the probabilistic seismic hazard assessment (PSHA) method. This method was carried out based on a recent data set to take into account the historic seismicity and updated instrumental seismicity. A homogenous earthquake catalogue was compiled and a proposed seismic sources model was presented. Attenuation equations that recently recommended by experts and developed based upon earthquake data obtained from tectonic environments similar to those in and around the studied area were weighted and used for assessment of seismic hazard in the frame of logic tree approach. Considering a grid of 1.2 × 1.2 km covering the study area, ground acceleration for every node was calculated. Hazard maps at bedrock conditions were produced for peak ground acceleration, in addition to return periods of 74, 475 and 2475 years.

Identification of potentially hazardous human gene products in GMO risk assessment.

Science.gov (United States)

Bergmans, Hans; Logie, Colin; Van Maanen, Kees; Hermsen, Harm; Meredyth, Michelle; Van Der Vlugt, Cécile

2008-01-01

Genetically modified organisms (GMOs), e.g. viral vectors, could threaten the environment if by their release they spread hazardous gene products. Even in contained use, to prevent adverse consequences, viral vectors carrying genes from mammals or humans should be especially scrutinized as to whether gene products that they synthesize could be hazardous in their new context. Examples of such potentially hazardous gene products (PHGPs) are: protein toxins, products of dominant alleles that have a role in hereditary diseases, gene products and sequences involved in genome rearrangements, gene products involved in immunomodulation or with an endocrine function, gene products involved in apoptosis, activated proto-oncogenes. For contained use of a GMO that carries a construct encoding a PHGP, the precautionary principle dictates that safety measures should be applied on a "worst case" basis, until the risks of the specific case have been assessed. The potential hazard of cloned genes can be estimated before empirical data on the actual GMO become available. Preliminary data may be used to focus hazard identification and risk assessment. Both predictive and empirical data may also help to identify what further information is needed to assess the risk of the GMO. A two-step approach, whereby a PHGP is evaluated for its conceptual dangers, then checked by data bank searches, is delineated here.

Risk assessment of major hazards: Hazardous materials transportation in urban areas

Energy Technology Data Exchange (ETDEWEB)

Hubert, Ph; Pages, P

1988-02-01

There is no doubt that, thanks to the pioneering studies of the late seventies and the early eighties, a methodology has been made available that allows risk management of hazardous transportation in urban areas. This approach can easily be extended to the management of other similar risks (storages and to some extent natural hazards). The methodology is both technically available and affordable. The insertion within the decision making processes deserves still some efforts. It has be seen that the applications are broad and numerous. They range from route selection to emergency preparedness, with some insights into acceptability considerations. One limit to the use of such studies, aiming to an objective assessment of the risk, is the complexity of the decision problems, where many factors are to be considered, the most subtle being the one linked to acceptability. However, as such studies develop, those factors start to be clarified, and decision makers learn how to use risk indices in this context. So at the present time it can be said that risk analyses are a valuable input into the decision making process in most cases. And, as more experience is acquired the uses are broader. As any technical innovation risk assessment modifies the approaches to the questions it is dealing with. It seems impossible now to treat those kinds of risks as was done ten years ago.

Risk assessment of major hazards: Hazardous materials transportation in urban areas

International Nuclear Information System (INIS)

Hubert, Ph.; Pages, P.

1988-02-01

There is no doubt that, thanks to the pioneering studies of the late seventies and the early eighties, a methodology has been made available that allows risk management of hazardous transportation in urban areas. This approach can easily be extended to the management of other similar risks (storages and to some extent natural hazards). The methodology is both technically available and affordable. The insertion within the decision making processes deserves still some efforts. It has be seen that the applications are broad and numerous. They range from route selection to emergency preparedness, with some insights into acceptability considerations. One limit to the use of such studies, aiming to an objective assessment of the risk, is the complexity of the decision problems, where many factors are to be considered, the most subtle being the one linked to acceptability. However, as such studies develop, those factors start to be clarified, and decision makers learn how to use risk indices in this context. So at the present time it can be said that risk analyses are a valuable input into the decision making process in most cases. And, as more experience is acquired the uses are broader. As any technical innovation risk assessment modifies the approaches to the questions it is dealing with. It seems impossible now to treat those kinds of risks as was done ten years ago

Hazard assessments of double-shell flammable gas tanks

International Nuclear Information System (INIS)

Fox, G.L.; Stepnewski, D.D.

1994-01-01

This report is the fourth in a series of hazard assessments performed on the double-shell flammable gas watch list tanks. This report focuses on hazards associated with the double-shell watch list tanks (101-AW, 103-AN, 104-AN, and 105-AN). While a similar assessment has already been performed for tank 103-SY, it is also included here to incorporate a more representative slurry gas mixture and provide a consistent basis for comparing results for all the flammable gas tanks. This report is intended to provide an in-depth assessment by considering the details of the gas release event and slurry gas mixing as the gas is released from the waste. The consequences of postulated gas ignition are evaluated using a plume burn model and updated ignition frequency predictions. Tank pressurization which results from a gas burn, along with the structural response, is also considered. The report is intended to support the safety basis for work activities in flammable gas tanks by showing margins to safety limits that are available in the design and procedures

Collateral benefits and hidden hazards of soil arsenic during abatement assessment of residential lead hazards

International Nuclear Information System (INIS)

Elless, M.P.; Ferguson, B.W.; Bray, C.A.; Patch, S.; Mielke, H.; Blaylock, M.J.

2008-01-01

Abatement of soil-lead hazards may also reduce human exposure to other soil toxins, thereby achieving significant collateral benefits that are not accounted for today. This proposition was tested with the specific case of soil-arsenic, where 1726 residential soil samples were collected and analyzed for lead and arsenic. The study found that these two toxins coexisted in most samples, but their concentrations were weakly correlated, reflecting the differing sources for each toxin. Collateral benefits of 9% would be achieved during abatement of the lead-contaminated soils having elevated arsenic concentrations. However, a hidden hazard of 16% was observed by overlooking elevated arsenic concentrations in soils having lead concentrations not requiring abatement. This study recommends that soil samples collected under HUD programs should be collected from areas of lead and arsenic deposition and tested for arsenic as well as lead, and that soil abatement decisions consider soil-arsenic as well as soil-lead guidelines. - Coexistence of arsenic at elevated concentrations with lead in residential soils undergoing lead hazard assessment is often overlooked, providing either collateral benefits or hidden hazards

Slope Hazard and Risk Assessment in the Tropics: Malaysia' Experience

Science.gov (United States)

Mohamad, Zakaria; Azahari Razak, Khamarrul; Ahmad, Ferdaus; Manap, Mohamad Abdul; Ramli, Zamri; Ahmad, Azhari; Mohamed, Zainab

2015-04-01

The increasing number of geological hazards in Malaysia has often resulted in casualties and extensive devastation with high mitigation cost. Given the destructive capacity and high frequency of disaster, Malaysia has taken a step forward to address the multi-scale landslide risk reduction emphasizing pre-disaster action rather than post-disaster reaction. Slope hazard and risk assessment in a quantitative manner at regional and national scales remains challenging in Malaysia. This paper presents the comprehensive methodology framework and operational needs driven by modern and advanced geospatial technology to address the aforementioned issues in the tropics. The Slope Hazard and Risk Mapping, the first national project in Malaysia utilizing the multi-sensor LIDAR has been critically implemented with the support of multi- and trans-disciplinary partners. The methodological model has been formulated and evaluated given the complexity of risk scenarios in this knowledge driven project. Instability slope problems in the urban, mountainous and tectonic landscape are amongst them, and their spatial information is of crucial for regional landslide assessment. We develop standard procedures with optimal parameterization for susceptibility, hazard and risk assessment in the selected regions. Remarkably, we are aiming at producing an utmost complete landslide inventory in both space and time. With the updated reliable terrain and landscape models, the landslide conditioning factor maps can be accurately derived depending on the landslide types and failure mechanisms which crucial for hazard and risk assessment. We also aim to improve the generation of elements at risk for landslide and promote integrated approaches for a better disaster risk analysis. As a result, a new tool, notably multi-sensor LIDAR technology is a very promising tool for an old geological problem and its derivative data for hazard and risk analysis is an effective preventive measure in Malaysia

[Informatics support for risk assessment and identification of preventive measures in small and micro-enterprises: occupational hazard datasheets].

Science.gov (United States)

de Merich, D; Forte, Giulia

2011-01-01

Risk assessment is the fundamental process of an enterprise's prevention system and is the principal mandatory provision contained in the Health and Safety Law (Legislative Decree 81/2008) amended by Legislative Decree 106/2009. In order to properly comply with this obligation also in small-sized enterprises, the appropriate regulatory bodies should provide the enterprises with standardized tools and methods for identifying, assessing and managing risks. To assist in particular small and micro-enterprises (SMEs) with risk assessment, by providing a flexible tool that can also be standardized in the form of a datasheet, that can be updated with more detailed information on the various work contexts in Italy. Official efforts to provide Italian SMEs with information may initially make use of the findings of research conducted by ISPESL over the past 20 years, thanks in part to cooperation with other institutions (Regions, INAIL-National Insurance Institute for Occupational Accidents and Diseases), which have led to the creation of an information system on prevention consisting of numerous databases, both statistical and documental ("National System of Surveillance on fatal and serious accidents", "National System of Surveillance on work-related diseases", "Sector hazard profiles" database, "Solutions and Best Practices" database, "Technical Guidelines" database, "Training packages for prevention professionals in enterprises" database). With regard to evaluation criteria applicable within the enterprise, the possibility of combining traditional and uniform areas of assessment (by sector or by risk factor) with assessments by job/occupation has become possible thanks to the cooperation agreement made in 2009 by ISPESL, the ILO (International Labour Organisation) of Geneva and IIOSH (Israel Institute for Occupational Health and Hygiene) regarding the creation of an international Database (HDODB) based on risk datasheets per occupation. The project sets out to assist in

Landslide hazard assessment of the Black sea coastline (Caucasus, Russia) via drones

Science.gov (United States)

Kazeev, Andrey; Postoev, German; Fedotova, Ksenia

2017-04-01

Landslide hazard assessment of slopes of Sochi was performed along the railway between the cities Tuapse and Adler (total length 103 km). The railway passes through the territory with active development of hazardous geological processes such as landslides, rock falls and debris-flows. By the beginning of 2016, 36 landslide sites were discovered along the railway (total length 34 km), 48 rock-fall sites (length 31 km), and 5 debris-flow sites (length 0.14 km). In recent years the intensification of deformations was observed. For instance, during previous 10 years (1996¬¬-2005) 28 sudden deformations occurred due to slope processes, which caused interruptions in traffic. And in the present decade (2006-2015), 72 deformations were recorded. High landslide activity and economic loss determined the necessity of complex investigations of engineering geological conditions of landslides development and causes of its intensification. The protection strategy development was needed to minimize negative consequences. Thus, the investigations of landslide situation along the railway "Tuapse - Adler" included the categorization of landslide sites by level of hazard, with risk assessment based on numerical criteria. Preliminary evaluation of landslide hazard for the railway was conducted via the analysis of archived engineering-geological documents. 13 of 36 landslide sites (total length 13 km) were selected, reflecting the variety and peculiarities of landslide displacements on slopes (both active and inactive sites). Visual field observations of landslide slopes using drone "DJI Phantom 4" were completed during the second stage of this investigation. High-resolution photographs of landslide cirques, cracks, scarp walls, vegetation features were obtained via drone, which would have been impossible to obtain from the ground in conditions of dense subtropical vegetation cover. Possible approaches to the landslide activity and hazard assessment were evaluated: slope stability

Tsunami hazard and risk assessment in El Salvador

Science.gov (United States)

González, M.; González-Riancho, P.; Gutiérrez, O. Q.; García-Aguilar, O.; Aniel-Quiroga, I.; Aguirre, I.; Alvarez, J. A.; Gavidia, F.; Jaimes, I.; Larreynaga, J. A.

2012-04-01

Tsunamis are relatively infrequent phenomena representing a greater threat than earthquakes, hurricanes and tornadoes, causing the loss of thousands of human lives and extensive damage to coastal infrastructure around the world. Several works have attempted to study these phenomena in order to understand their origin, causes, evolution, consequences, and magnitude of their damages, to finally propose mechanisms to protect coastal societies. Advances in the understanding and prediction of tsunami impacts allow the development of adaptation and mitigation strategies to reduce risk on coastal areas. This work -Tsunami Hazard and Risk Assessment in El Salvador-, funded by AECID during the period 2009-12, examines the state of the art and presents a comprehensive methodology for assessing the risk of tsunamis at any coastal area worldwide and applying it to the coast of El Salvador. The conceptual framework is based on the definition of Risk as the probability of harmful consequences or expected losses resulting from a given hazard to a given element at danger or peril, over a specified time period (European Commission, Schneiderbauer et al., 2004). The HAZARD assessment (Phase I of the project) is based on propagation models for earthquake-generated tsunamis, developed through the characterization of tsunamigenic sources -sismotectonic faults- and other dynamics under study -tsunami waves, sea level, etc.-. The study area is located in a high seismic activity area and has been hit by 11 tsunamis between 1859 and 1997, nine of them recorded in the twentieth century and all generated by earthquakes. Simulations of historical and potential tsunamis with greater or lesser affection to the country's coast have been performed, including distant sources, intermediate and close. Deterministic analyses of the threats under study -coastal flooding- have been carried out, resulting in different hazard maps (maximum wave height elevation, maximum water depth, minimum tsunami

Assessing natural hazard risk using images and data

Science.gov (United States)

Mccullough, H. L.; Dunbar, P. K.; Varner, J. D.; Mungov, G.

2012-12-01

Photographs and other visual media provide valuable pre- and post-event data for natural hazard assessment. Scientific research, mitigation, and forecasting rely on visual data for risk analysis, inundation mapping and historic records. Instrumental data only reveal a portion of the whole story; photographs explicitly illustrate the physical and societal impacts from the event. Visual data is rapidly increasing as the availability of portable high resolution cameras and video recorders becomes more attainable. Incorporating these data into archives ensures a more complete historical account of events. Integrating natural hazards data, such as tsunami, earthquake and volcanic eruption events, socio-economic information, and tsunami deposits and runups along with images and photographs enhances event comprehension. Global historic databases at NOAA's National Geophysical Data Center (NGDC) consolidate these data, providing the user with easy access to a network of information. NGDC's Natural Hazards Image Database (ngdc.noaa.gov/hazardimages) was recently improved to provide a more efficient and dynamic user interface. It uses the Google Maps API and Keyhole Markup Language (KML) to provide geographic context to the images and events. Descriptive tags, or keywords, have been applied to each image, enabling easier navigation and discovery. In addition, the Natural Hazards Map Viewer (maps.ngdc.noaa.gov/viewers/hazards) provides the ability to search and browse data layers on a Mercator-projection globe with a variety of map backgrounds. This combination of features creates a simple and effective way to enhance our understanding of hazard events and risks using imagery.

Risk assessment of chemicals in food and diet: Hazard identification by methods of animal-based toxicology

DEFF Research Database (Denmark)

Barlow, S. M.; Greig, J. B.; Bridges, J. W.

2002-01-01

the current state of the science of risk assessment of chemicals in food and diet, by consideration of the four stages of risk assessment, that is. hazard identification. hazard characterisation, exposure assessment and risk characterisation. The contribution of animal-based methods in toxicology to hazard......, on hazard identification for food chemicals, such as new measurement techniques, the use of transgenic animals, assessment of hormone balance and the possibilities for conducting studies in which common human diseases have been modelled. is also considered. (C) 2002 ILSI. Published by Elsevier Science Ltd....... All rights reserved....

The Contribution of Palaeoseismology to Seismic Hazard Assessment in Site Evaluation for Nuclear Installations

International Nuclear Information System (INIS)

2015-06-01

IAEA Safety Standards Series No. SSG-9, Seismic Hazards in Site Evaluation for Nuclear Installations, published in 2010, covers all aspects of site evaluation relating to seismic hazards and recommends the use of prehistoric, historical and instrumental earthquake data in seismic hazard assessments. Prehistoric data on earthquakes cover a much longer period than do historical and instrumental data. However, gathering such data is generally difficult in most regions of the world, owing to an absence of human records. Prehistoric data on earthquakes can be obtained through the use of palaeoseismic techniques. This publication describes the current status and practices of palaeoseismology, in order to support Member States in meeting the recommendations of SSG-9 and in establishing the necessary earthquake related database for seismic hazard assessment and reassessment. At a donors’ meeting of the International Seismic Safety Centre Extrabudgetary Project in January 2011, it was suggested to develop detailed guidelines on seismic hazards. Soon after the meeting, the disastrous Great East Japan Earthquake and Tsunami of 11 March 2011 and the consequent accident at the Fukushima Daiichi nuclear power plant occurred. The importance of palaeoseismology for seismic hazard assessment in site evaluation was highlighted by the lessons learned from the Fukushima Daiichi nuclear power plant accident. However, no methodology for performing investigations using palaeoseismic techniques has so far been available in an IAEA publication. The detailed guidelines and practical tools provided here will be of value to nuclear power plant operating organizations, regulatory bodies, vendors, technical support organizations and researchers in the area of seismic hazard assessment in site evaluation for nuclear installations, and the information will be of importance in support of hazard assessments in the future

Bioassay-based risk assessment of hazardous waste

Energy Technology Data Exchange (ETDEWEB)

Donnelly, K.C.; Brown, K.W.; He, L.Y. [Texas A and M Univ., College Station, TX (United States)

1994-12-31

Microbial bioassays have been used to assess the genotoxic hazard at more than 30 different hazardous waste sites. Environmental samples were extracted with dichloromethane and methanol, and the resulting residue tested using GC/MS analysis as well as the Salmonella Microsomal and E. coli Prophage Induction assays. At a munitions wastewater contaminated site, there was no correlation between mutagenicity in bacteria, and the risk as estimated from chemical analysis data of trinitrotoluene. Samples 202 and 204 from a coal gasification site contained 72 mg/kg and 9 mg/kg benzo(a)pyrene, whereas the mutagenic responses of these samples were 231 net revertants/mg and 902 revertants/mg, respectively. The data suggest that microbial bioassays provide a valuable tool for monitoring the interactions of the components of a complex mixture.

Seismic hazard assessment for the Caucasus test area

Czech Academy of Sciences Publication Activity Database

Balassanian, S.; Ashirov, T.; Chelidze, T.; Gassanov, A.; Kondorskaya, N.; Molchan, G.; Pustovitenko, B.; Trifonov, V.; Ulomov, V.; Giardini, D.; Erdik, M.; Ghafory-Ashtiany, M.; Grunthal, G.; Mayer-Rosa, D.; Schenk, Vladimír; Stucchi, M.

1999-01-01

Roč. 42, č. 6 (1999), s. 1139-1151 ISSN 0365-2556 R&D Projects: GA AV ČR Global Seismic Hazard Assessment Program (GSHAP) - project of the UN International Decade of Natural Disaster Reduction and International Litosphere Program. Subject RIV: DC - Siesmology, Volcanology, Earth Structure

Assessment of tsunami hazard to the U.S. Atlantic margin

Science.gov (United States)

ten Brink, Uri S.; Chaytor, Jason; Geist, Eric L.; Brothers, Daniel S.; Andrews, Brian D.

2014-01-01

Tsunami hazard is a very low-probability, but potentially high-risk natural hazard, posing unique challenges to scientists and policy makers trying to mitigate its impacts. These challenges are illustrated in this assessment of tsunami hazard to the U.S. Atlantic margin. Seismic activity along the U.S. Atlantic margin in general is low, and confirmed paleo-tsunami deposits have not yet been found, suggesting a very low rate of hazard. However, the devastating 1929 Grand Banks tsunami along the Atlantic margin of Canada shows that these events continue to occur. Densely populated areas, extensive industrial and port facilities, and the presence of ten nuclear power plants along the coast, make this region highly vulnerable to flooding by tsunamis and therefore even low-probability events need to be evaluated.

Emergency Preparedness Hazards Assessment for solid waste management facilities in E-area not previously evaluated

International Nuclear Information System (INIS)

Hadlock, D.J.

1999-01-01

This report documents the facility Emergency Preparedness Hazards Assessment (EPHA) for the Solid Waste Management Department (SWMD) activities located on the Department of Energy (DOE) Savannah River Site (SRS) within E Area that are not described in the EPHAs for Mixed Hazardous Waste storage, the TRU Waste Storage Pads or the E-Area Vaults. The hazards assessment is intended to identify and analyze those hazards that are significant enough to warrant consideration in the SWMD operational emergency management program

Probabilistic versus deterministic hazard assessment in liquefaction susceptible zones

Science.gov (United States)

Daminelli, Rosastella; Gerosa, Daniele; Marcellini, Alberto; Tento, Alberto

2015-04-01

Probabilistic seismic hazard assessment (PSHA), usually adopted in the framework of seismic codes redaction, is based on Poissonian description of the temporal occurrence, negative exponential distribution of magnitude and attenuation relationship with log-normal distribution of PGA or response spectrum. The main positive aspect of this approach stems into the fact that is presently a standard for the majority of countries, but there are weak points in particular regarding the physical description of the earthquake phenomenon. Factors like site effects, source characteristics like duration of the strong motion and directivity that could significantly influence the expected motion at the site are not taken into account by PSHA. Deterministic models can better evaluate the ground motion at a site from a physical point of view, but its prediction reliability depends on the degree of knowledge of the source, wave propagation and soil parameters. We compare these two approaches in selected sites affected by the May 2012 Emilia-Romagna and Lombardia earthquake, that caused widespread liquefaction phenomena unusually for magnitude less than 6. We focus on sites liquefiable because of their soil mechanical parameters and water table level. Our analysis shows that the choice between deterministic and probabilistic hazard analysis is strongly dependent on site conditions. The looser the soil and the higher the liquefaction potential, the more suitable is the deterministic approach. Source characteristics, in particular the duration of strong ground motion, have long since recognized as relevant to induce liquefaction; unfortunately a quantitative prediction of these parameters appears very unlikely, dramatically reducing the possibility of their adoption in hazard assessment. Last but not least, the economic factors are relevant in the choice of the approach. The case history of 2012 Emilia-Romagna and Lombardia earthquake, with an officially estimated cost of 6 billions

Identification and assessment of hazardous compounds in drinking water.

Science.gov (United States)

Fawell, J K; Fielding, M

1985-12-01

The identification of organic chemicals in drinking water and their assessment in terms of potential hazardous effects are two very different but closely associated tasks. In relation to both continuous low-level background contamination and specific, often high-level, contamination due to pollution incidents, the identification of contaminants is a pre-requisite to evaluation of significant hazards. Even in the case of the rapidly developing short-term bio-assays which are applied to water to indicate a potential genotoxic hazard (for example Ames tests), identification of the active chemicals is becoming a major factor in the further assessment of the response. Techniques for the identification of low concentrations of organic chemicals in drinking water have developed remarkably since the early 1970s and methods based upon gas chromatography-mass spectrometry (GC-MS) have revolutionised qualitative analysis of water. Such techniques are limited to "volatile" chemicals and these usually constitute a small fraction of the total organic material in water. However, in recent years there have been promising developments in techniques for "non-volatile" chemicals in water. Such techniques include combined high-performance liquid chromatography-mass spectrometry (HPLC-MS) and a variety of MS methods, involving, for example, field desorption, fast atom bombardment and thermospray ionisation techniques. In the paper identification techniques in general are reviewed and likely future developments outlined. The assessment of hazards associated with chemicals identified in drinking and related waters usually centres upon toxicology - an applied science which involves numerous disciplines. The paper examines the toxicological information needed, the quality and deployment of such information and discusses future research needs. Application of short-term bio-assays to drinking water is a developing area and one which is closely involved with, and to some extent dependent on

Setting the Stage for Harmonized Risk Assessment by Seismic Hazard Harmonization in Europe (SHARE)

Science.gov (United States)

Woessner, Jochen; Giardini, Domenico; SHARE Consortium

2010-05-01

Probabilistic seismic hazard assessment (PSHA) is arguably one of the most useful products that seismology can offer to society. PSHA characterizes the best available knowledge on the seismic hazard of a study area, ideally taking into account all sources of uncertainty. Results form the baseline for informed decision making, such as building codes or insurance rates and provide essential input to each risk assessment application. Several large scale national and international projects have recently been launched aimed at improving and harmonizing PSHA standards around the globe. SHARE (www.share-eu.org) is the European Commission funded project in the Framework Programme 7 (FP-7) that will create an updated, living seismic hazard model for the Euro-Mediterranean region. SHARE is a regional component of the Global Earthquake Model (GEM, www.globalquakemodel.org), a public/private partnership initiated and approved by the Global Science Forum of the OECD-GSF. GEM aims to be the uniform, independent and open access standard to calculate and communicate earthquake hazard and risk worldwide. SHARE itself will deliver measurable progress in all steps leading to a harmonized assessment of seismic hazard - in the definition of engineering requirements, in the collection of input data, in procedures for hazard assessment, and in engineering applications. SHARE scientists will create a unified framework and computational infrastructure for seismic hazard assessment and produce an integrated European probabilistic seismic hazard assessment (PSHA) model and specific scenario based modeling tools. The results will deliver long-lasting structural impact in areas of societal and economic relevance, they will serve as reference for the Eurocode 8 (EC8) application, and will provide homogeneous input for the correct seismic safety assessment for critical industry, such as the energy infrastructures and the re-insurance sector. SHARE will cover the whole European territory, the

Seismic hazard assessment of Iran

Directory of Open Access Journals (Sweden)

M. Ghafory-Ashtiany

1999-06-01

Full Text Available The development of the new seismic hazard map of Iran is based on probabilistic seismic hazard computation using the historical earthquakes data, geology, tectonics, fault activity and seismic source models in Iran. These maps have been prepared to indicate the earthquake hazard of Iran in the form of iso-acceleration contour lines, and seismic hazard zoning, by using current probabilistic procedures. They display the probabilistic estimates of Peak Ground Acceleration (PGA for the return periods of 75 and 475 years. The maps have been divided into intervals of 0.25 degrees in both latitudinal and longitudinal directions to calculate the peak ground acceleration values at each grid point and draw the seismic hazard curves. The results presented in this study will provide the basis for the preparation of seismic risk maps, the estimation of earthquake insurance premiums, and the preliminary site evaluation of critical facilities.

Multi-hazard risk assessment applied to hydraulic fracturing operations

Science.gov (United States)

Garcia-Aristizabal, Alexander; Gasparini, Paolo; Russo, Raffaella; Capuano, Paolo

2017-04-01

Without exception, the exploitation of any energy resource produces impacts and intrinsically bears risks. Therefore, to make sound decisions about future energy resource exploitation, it is important to clearly understand the potential environmental impacts in the full life-cycle of an energy development project, distinguishing between the specific impacts intrinsically related to exploiting a given energy resource and those shared with the exploitation of other energy resources. Technological advances as directional drilling and hydraulic fracturing have led to a rapid expansion of unconventional resources (UR) exploration and exploitation; as a consequence, both public health and environmental concerns have risen. The main objective of a multi-hazard risk assessment applied to the development of UR is to assess the rate (or the likelihood) of occurrence of incidents and the relative potential impacts on surrounding environment, considering different hazards and their interactions. Such analyses have to be performed considering the different stages of development of a project; however, the discussion in this paper is mainly focused on the analysis applied to the hydraulic fracturing stage of a UR development project. The multi-hazard risk assessment applied to the development of UR poses a number of challenges, making of this one a particularly complex problem. First, a number of external hazards might be considered as potential triggering mechanisms. Such hazards can be either of natural origin or anthropogenic events caused by the same industrial activities. Second, failures might propagate through the industrial elements, leading to complex scenarios according to the layout of the industrial site. Third, there is a number of potential risk receptors, ranging from environmental elements (as the air, soil, surface water, or groundwater) to local communities and ecosystems. The multi-hazard risk approach for this problem is set by considering multiple hazards

Beyond eruptive scenarios: assessing tephra fallout hazard from Neapolitan volcanoes.

Science.gov (United States)

Sandri, Laura; Costa, Antonio; Selva, Jacopo; Tonini, Roberto; Macedonio, Giovanni; Folch, Arnau; Sulpizio, Roberto

2016-04-12

Assessment of volcanic hazards is necessary for risk mitigation. Typically, hazard assessment is based on one or a few, subjectively chosen representative eruptive scenarios, which use a specific combination of eruptive sizes and intensities to represent a particular size class of eruption. While such eruptive scenarios use a range of representative members to capture a range of eruptive sizes and intensities in order to reflect a wider size class, a scenario approach neglects to account for the intrinsic variability of volcanic eruptions, and implicitly assumes that inter-class size variability (i.e. size difference between different eruptive size classes) dominates over intra-class size variability (i.e. size difference within an eruptive size class), the latter of which is treated as negligible. So far, no quantitative study has been undertaken to verify such an assumption. Here, we adopt a novel Probabilistic Volcanic Hazard Analysis (PVHA) strategy, which accounts for intrinsic eruptive variabilities, to quantify the tephra fallout hazard in the Campania area. We compare the results of the new probabilistic approach with the classical scenario approach. The results allow for determining whether a simplified scenario approach can be considered valid, and for quantifying the bias which arises when full variability is not accounted for.

Assessment of liquefaction-induced hazards using Bayesian networks based on standard penetration test data

Science.gov (United States)

Tang, Xiao-Wei; Bai, Xu; Hu, Ji-Lei; Qiu, Jiang-Nan

2018-05-01

Liquefaction-induced hazards such as sand boils, ground cracks, settlement, and lateral spreading are responsible for considerable damage to engineering structures during major earthquakes. Presently, there is no effective empirical approach that can assess different liquefaction-induced hazards in one model. This is because of the uncertainties and complexity of the factors related to seismic liquefaction and liquefaction-induced hazards. In this study, Bayesian networks (BNs) are used to integrate multiple factors related to seismic liquefaction, sand boils, ground cracks, settlement, and lateral spreading into a model based on standard penetration test data. The constructed BN model can assess four different liquefaction-induced hazards together. In a case study, the BN method outperforms an artificial neural network and Ishihara and Yoshimine's simplified method in terms of accuracy, Brier score, recall, precision, and area under the curve (AUC) of the receiver operating characteristic (ROC). This demonstrates that the BN method is a good alternative tool for the risk assessment of liquefaction-induced hazards. Furthermore, the performance of the BN model in estimating liquefaction-induced hazards in Japan's 2011 Tōhoku earthquake confirms its correctness and reliability compared with the liquefaction potential index approach. The proposed BN model can also predict whether the soil becomes liquefied after an earthquake and can deduce the chain reaction process of liquefaction-induced hazards and perform backward reasoning. The assessment results from the proposed model provide informative guidelines for decision-makers to detect the damage state of a field following liquefaction.

Hazard Assessment in a Big Data World

Science.gov (United States)

Kossobokov, Vladimir; Nekrasova, Anastasia

2017-04-01

Open data in a Big Data World provides unprecedented opportunities for enhancing scientific studies and better understanding of the Earth System. At the same time, it opens wide avenues for deceptive associations in inter- and transdisciplinary data misleading to erroneous predictions, which are unacceptable for implementation. Even the advanced tools of data analysis may lead to wrong assessments when inappropriately used to describe the phenomenon under consideration. A (self-) deceptive conclusion could be avoided by verification of candidate models in experiments on empirical data and in no other way. Seismology is not an exception. Moreover, seismic evidences accumulated to-date demonstrate clearly that most of the empirical relations commonly accepted in early history of instrumental seismology can be proved erroneous when subjected to objective hypothesis testing. In many cases of seismic hazard assessment (SHA), either probabilistic or deterministic, term-less or short-term, the claims of a high potential of a model forecasts are based on a flawed application of statistics and, therefore, are hardly suitable for communication to decision makers, which situation creates numerous deception points and resulted controversies. So far, most, if not all, the standard probabilistic methods to assess seismic hazard and associated risks are based on subjective, commonly unrealistic, and even erroneous assumptions about seismic recurrence and none of the proposed short-term precursory signals showed sufficient evidence to be used as a reliable precursor of catastrophic earthquakes. Accurate testing against real observations must be done in advance claiming seismically hazardous areas and/or times. The set of errors of the first and second kind in such a comparison permits evaluating the SHA method effectiveness and determining the optimal choice of parameters in regard to a user-defined cost-benefit function. The information obtained in testing experiments may supply

Probabilistic disaggregation of a spatial portfolio of exposure for natural hazard risk assessment

DEFF Research Database (Denmark)

Custer, Rocco; Nishijima, Kazuyoshi

2018-01-01

In natural hazard risk assessment situations are encountered where information on the portfolio of exposure is only available in a spatially aggregated form, hindering a precise risk assessment. Recourse might be found in the spatial disaggregation of the portfolio of exposure to the resolution...... of a portfolio of buildings in two communes in Switzerland and the results are compared to sample observations. The relevance of probabilistic disaggregation uncertainty in natural hazard risk assessment is illustrated with the example of a simple flood risk assessment....

Hazard Identification, Risk Assessment and Risk Control (HIRARC Accidents at Power Plant

Directory of Open Access Journals (Sweden)

Ahmad Asmalia Che

2016-01-01

Full Text Available Power plant had a reputation of being one of the most hazardous workplace environments. Workers in the power plant face many safety risks due to the nature of the job. Although power plants are safer nowadays since the industry has urged the employer to improve their employees’ safety, the employees still stumble upon many hazards thus accidents at workplace. The aim of the present study is to investigate work related accidents at power plants based on HIRARC (Hazard Identification, Risk Assessment and Risk Control process. The data were collected at two coal-fired power plant located in Malaysia. The finding of the study identified hazards and assess risk relate to accidents occurred at the power plants. The finding of the study suggested the possible control measures and corrective actions to reduce or eliminate the risk that can be used by power plant in preventing accidents from occurred

Multi-Hazard Advanced Seismic Probabilistic Risk Assessment Tools and Applications

International Nuclear Information System (INIS)

Coleman, Justin L.; Bolisetti, Chandu; Veeraraghavan, Swetha; Parisi, Carlo; Prescott, Steven R.; Gupta, Abhinav

2016-01-01

Design of nuclear power plant (NPP) facilities to resist natural hazards has been a part of the regulatory process from the beginning of the NPP industry in the United States (US), but has evolved substantially over time. The original set of approaches and methods was entirely deterministic in nature and focused on a traditional engineering margins-based approach. However, over time probabilistic and risk-informed approaches were also developed and implemented in US Nuclear Regulatory Commission (NRC) guidance and regulation. A defense-in-depth framework has also been incorporated into US regulatory guidance over time. As a result, today, the US regulatory framework incorporates deterministic and probabilistic approaches for a range of different applications and for a range of natural hazard considerations. This framework will continue to evolve as a result of improved knowledge and newly identified regulatory needs and objectives, most notably in response to the NRC activities developed in response to the 2011 Fukushima accident in Japan. Although the US regulatory framework has continued to evolve over time, the tools, methods and data available to the US nuclear industry to meet the changing requirements have not kept pace. Notably, there is significant room for improvement in the tools and methods available for external event probabilistic risk assessment (PRA), which is the principal assessment approach used in risk-informed regulations and risk-informed decision-making applied to natural hazard assessment and design. This is particularly true if PRA is applied to natural hazards other than seismic loading. Development of a new set of tools and methods that incorporate current knowledge, modern best practice, and state-of-the-art computational resources would lead to more reliable assessment of facility risk and risk insights (e.g., the SSCs and accident sequences that are most risk-significant), with less uncertainty and reduced conservatisms.

Multi-Hazard Advanced Seismic Probabilistic Risk Assessment Tools and Applications

Energy Technology Data Exchange (ETDEWEB)

Coleman, Justin L. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Bolisetti, Chandu [Idaho National Lab. (INL), Idaho Falls, ID (United States); Veeraraghavan, Swetha [Idaho National Lab. (INL), Idaho Falls, ID (United States); Parisi, Carlo [Idaho National Lab. (INL), Idaho Falls, ID (United States); Prescott, Steven R. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Gupta, Abhinav [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2016-09-01

Design of nuclear power plant (NPP) facilities to resist natural hazards has been a part of the regulatory process from the beginning of the NPP industry in the United States (US), but has evolved substantially over time. The original set of approaches and methods was entirely deterministic in nature and focused on a traditional engineering margins-based approach. However, over time probabilistic and risk-informed approaches were also developed and implemented in US Nuclear Regulatory Commission (NRC) guidance and regulation. A defense-in-depth framework has also been incorporated into US regulatory guidance over time. As a result, today, the US regulatory framework incorporates deterministic and probabilistic approaches for a range of different applications and for a range of natural hazard considerations. This framework will continue to evolve as a result of improved knowledge and newly identified regulatory needs and objectives, most notably in response to the NRC activities developed in response to the 2011 Fukushima accident in Japan. Although the US regulatory framework has continued to evolve over time, the tools, methods and data available to the US nuclear industry to meet the changing requirements have not kept pace. Notably, there is significant room for improvement in the tools and methods available for external event probabilistic risk assessment (PRA), which is the principal assessment approach used in risk-informed regulations and risk-informed decision-making applied to natural hazard assessment and design. This is particularly true if PRA is applied to natural hazards other than seismic loading. Development of a new set of tools and methods that incorporate current knowledge, modern best practice, and state-of-the-art computational resources would lead to more reliable assessment of facility risk and risk insights (e.g., the SSCs and accident sequences that are most risk-significant), with less uncertainty and reduced conservatisms.

assessment of radiological hazard indices from surface soil to ...

African Journals Online (AJOL)

samples in Eagle, Atlas and rock cement companies in Port Harcourt was carried out by ... and external hazard indices in order to assess the radiological implication to the people .... Sciences & Environmental Management, Vol. 9, No. 3, pp.

78 FR 33894 - Proposed Information Collection (Open Burn Pit Registry Airborne Hazard Self-Assessment...

Science.gov (United States)

2013-06-05

... chemicals and fumes caused by open burn pits. DATES: Written comments and recommendations on the proposed... to ``OMB Control No. 2900-NEW, Open Burn Pit Registry Airborne Hazard Self-Assessment Questionnaire.... Title: Open Burn Pit Registry Airborne Hazard Self-Assessment Questionnaire, VA Form 10-10066. OMB...

The Global Seismic Hazard Assessment Program (GSHAP - 1992/1999

Directory of Open Access Journals (Sweden)

D. Giardini

1999-06-01

Full Text Available The United Nations, recognizing natural disasters as a major threat to human life and development, designed the 1990-1999 period as the International Decade for Natural Disaster Reduction (UN/IDNDR; UN Res. 42/169/ 1987. Among the IDNDR Demonstration Projects is the Global Seismic Hazard Assessment Program (GSHAP, launched in 1992 by the International Lithosphere Program (ILP and implemented in the 1992-1999 period. In order to mitigate the risk associated to the recurrence of earthquakes, the GSHAP promoted a regionally coordinated, homogeneous approach to seismic hazard evaluation. To achieve a global dimension, the GSHAP established initially a mosaic of regions and multinational test areas, then expanded to cover whole continents and finally the globe. The GSHAP Global Map of Seismic Hazard integrates the results obtained in the regional areas and depicts Peak-Ground-Acceleration (PGA with 10% chance of exceedance in 50 years, corresponding to a return period of 475 years. All regional results and the Global Map of Seismic Hazard are published in 1999 and available on the GSHAP homepage on http://seismo.ethz.ch/GSHAP/.

Cost assessment of natural hazards in Europe - state-of-the-art, knowledge gaps and recommendations

Science.gov (United States)

Meyer, V.; Becker, N.; Markantonis, V.; Schwarze, R.; van den Bergh, J. C. J. M.; Bouwer, L. M.; Bubeck, P.; Ciavola, P.; Thieken, A. H.; Genovese, E.; Green, C.; Hallegatte, S.; Kreibich, H.; Lequeux, Q.; Viavattenne, C.; Logar, I.; Papyrakis, E.; Pfurtscheller, C.; Poussin, J.; Przyluski, V.

2012-04-01

Effective and efficient reduction of natural hazard risks requires a thorough understanding of the costs of natural hazards in order to develop sustainable risk management strategies. The current methods that assess the costs of different natural hazards employ a diversity of terminologies and approaches for different hazards and impacted sectors. This makes it difficult to arrive at robust, comprehensive and comparable cost figures. The CONHAZ (Costs of Natural Hazards) project aimed to compile and synthesise current knowledge on cost assessment methods in order to strengthen the role of cost assessments in the development of integrated natural hazard management and adaptation planning. In order to achieve this, CONHAZ has adopted a comprehensive approach, considering natural hazards ranging from droughts, floods and coastal hazards to Alpine hazards, as well as different impacted sectors and cost types. Its specific objectives have been 1) to compile the state-of-the-art methods for cost assessment; 2) to analyse and assess these methods in terms of technical aspects, as well as terminology, data quality and availability, and research gaps; and 3) to synthesise resulting knowledge into recommendations and to identify further research needs. This presentation summarises the main results of CONHAZ. CONHAZ differentiates between direct tangible damages, losses due to business interruption, indirect damages, intangible effects, and costs of risk mitigation. It is shown that the main focus of cost assessment methods and their application in practice is on direct costs, while existing methods for assessing intangible and indirect effects are rather rarely applied and methods for assessing indirect effects often cannot be used on the scale of interest (e.g. the regional scale). Furthermore, methods often focus on single sectors and/or hazards, and only very few are able to reflect several sectors or multiple hazards. Process understanding and its use in cost assessment

Geostatistical analyses and hazard assessment on soil lead in Silvermines area, Ireland

International Nuclear Information System (INIS)

McGrath, David; Zhang Chaosheng; Carton, Owen T.

2004-01-01

Spatial distribution and hazard assessment of soil lead in the mining site of Silvermines, Ireland, were investigated using statistics, geostatistics and geographic information system (GIS) techniques. Positively skewed distribution and possible outlying values of Pb and other heavy metals were observed. Box-Cox transformation was applied in order to achieve normality in the data set and to reduce the effect of outliers. Geostatistical analyses were carried out, including calculation of experimental variograms and model fitting. The ordinary point kriging estimates of Pb concentration were mapped. Kriging standard deviations were regarded as the standard deviations of the interpolated pixel values, and a second map was produced, that quantified the probability of Pb concentration higher than a threshold value of 1000 mg/kg. These maps provide valuable information for hazard assessment and for decision support. - A probability map was produced that was useful for hazard assessment and decision support

Geostatistical analyses and hazard assessment on soil lead in Silvermines area, Ireland

Energy Technology Data Exchange (ETDEWEB)

McGrath, David; Zhang Chaosheng; Carton, Owen T

2004-01-01

Spatial distribution and hazard assessment of soil lead in the mining site of Silvermines, Ireland, were investigated using statistics, geostatistics and geographic information system (GIS) techniques. Positively skewed distribution and possible outlying values of Pb and other heavy metals were observed. Box-Cox transformation was applied in order to achieve normality in the data set and to reduce the effect of outliers. Geostatistical analyses were carried out, including calculation of experimental variograms and model fitting. The ordinary point kriging estimates of Pb concentration were mapped. Kriging standard deviations were regarded as the standard deviations of the interpolated pixel values, and a second map was produced, that quantified the probability of Pb concentration higher than a threshold value of 1000 mg/kg. These maps provide valuable information for hazard assessment and for decision support. - A probability map was produced that was useful for hazard assessment and decision support.

Probabilistic disaggregation model with application to natural hazard risk assessment of portfolios

OpenAIRE

Custer, Rocco; Nishijima, Kazuyoshi

2012-01-01

In natural hazard risk assessment, a resolution mismatch between hazard data and aggregated exposure data is often observed. A possible solution to this issue is the disaggregation of exposure data to match the spatial resolution of hazard data. Disaggregation models available in literature are usually deterministic and make use of auxiliary indicator, such as land cover, to spatially distribute exposures. As the dependence between auxiliary indicator and disaggregated number of exposures is ...

The methodology of environmental impacts assessment of environmentally hazardous facilities

OpenAIRE

Adamenko, Yaroslav

2017-01-01

The article deals with the methodology of environmental impacts assessment of environmentally hazardous facilities and activities. The stages of evaluation of environmental impacts are proved. The algorithm and technology of decision-making in the system of environmental impact assessments based on a multi-criteria utility theory are proposed.

Seismic Hazard characterization study using an earthquake source with Probabilistic Seismic Hazard Analysis (PSHA) method in the Northern of Sumatra

International Nuclear Information System (INIS)

Yahya, A.; Palupi, M. I. R.; Suharsono

2016-01-01

Sumatra region is one of the earthquake-prone areas in Indonesia because it is lie on an active tectonic zone. In 2004 there is earthquake with a moment magnitude of 9.2 located on the coast with the distance 160 km in the west of Nanggroe Aceh Darussalam and triggering a tsunami. These events take a lot of casualties and material losses, especially in the Province of Nanggroe Aceh Darussalam and North Sumatra. To minimize the impact of the earthquake disaster, a fundamental assessment of the earthquake hazard in the region is needed. Stages of research include the study of literature, collection and processing of seismic data, seismic source characterization and analysis of earthquake hazard by probabilistic methods (PSHA) used earthquake catalog from 1907 through 2014. The earthquake hazard represented by the value of Peak Ground Acceleration (PGA) and Spectral Acceleration (SA) in the period of 0.2 and 1 second on bedrock that is presented in the form of a map with a return period of 2475 years and the earthquake hazard curves for the city of Medan and Banda Aceh. (paper)

Risk assessment of hazardous waste transport - perspectives of GIS application

International Nuclear Information System (INIS)

Lazar, R.E.; Dumitrescu, M.; Stefanescu, I.

2001-01-01

Due to the increasing public awareness of the potential risks associated with waste transport, the environmental impact assessment of this activity has become an issue of major importance. This paper presents a project proposal, which can establish a national action plan for waste transport evaluation. Such a programme is sustained by the necessity to obtain an adequate method for the rapid and efficient estimation of individual and social risks due to the transport of hazardous substances in Romania. The main objective is to develop regional strategies for risk assessment in comprising: establishing the areas that must be investigated and their particular characteristics; identifying the transport activities in the areas; determining hazards; establishing the analysis criteria and prioritizing the study areas; evaluating continuous emissions; studying major accidents; studying population health; classifying the risks; establishing regional strategies; implementing political and regulatory measures. The project expectation is to provide a decision tool for risk managers and authorities in order to control or limit transportation and the storage of hazardous substances.(author)

Hazard risk and vulnerability assessment : Regional District of Nanaimo : final report

International Nuclear Information System (INIS)

2006-06-01

A Hazard Risk and Vulnerability Assessment (HRVA) is a mandated regulatory requirement in British Columbia that requires local authorities to prepare emergency plans that reflect the local authority's assessment of the relative risk of occurrence and the potential impact on people and property of the hazards, emergencies or disasters that could affect the jurisdictional area for which the local authority has responsibility. This report constituted an HRVA for the Regional District of Nanaimo, British Columbia. It presented the study scope and methodology and provided an overview of the Regional District of Nanaimo. This included information on the setting, demographics, and economy. Next, it discussed social vulnerability; critical response and recovery facilities; and critical infrastructure such as water, energy, telecommunications and transportation. A summary of the Regional District of Nanaimo's response capabilities that were considered when assessing the Regional District's overall risk to the hazards was also presented. Response capabilities were discussed with reference to fire and rescue; police; ambulance; and search and rescue. Emergency support and preparedness organizations were also identified. These included the Emergency Coordination Centre, environmental services, emergency social services, amateur radio and health authorities. Last, 33 hazards that could affect the Regional District of Nanaimo were identified and discussed. The study identified the following hazards as high risk: flooding; forest fires and wildland urban interface fires; and human diseases and pandemic. It was recommended that the advancement of business continuity planning in the Regional District of Nanaimo would help to reduce the impact of a possible human disease and pandemic risk outbreak affecting the population. 75 refs., 25 figs., 14 tabs., 2 appendices

A procedure for NEPA assessment of selenium hazards associated with mining.

Science.gov (United States)

Lemly, A Dennis

2007-02-01

This paper gives step-by-step instructions for assessing aquatic selenium hazards associated with mining. The procedure was developed to provide the U.S. Forest Service with a proactive capability for determining the risk of selenium pollution when it reviews mine permit applications in accordance with the National Environmental Policy Act (NEPA). The procedural framework is constructed in a decision-tree format in order to guide users through the various steps, provide a logical sequence for completing individual tasks, and identify key decision points. There are five major components designed to gather information on operational parameters of the proposed mine as well as key aspects of the physical, chemical, and biological environment surrounding it--geological assessment, mine operation assessment, hydrological assessment, biological assessment, and hazard assessment. Validation tests conducted at three mines where selenium pollution has occurred confirmed that the procedure will accurately predict ecological risks. In each case, it correctly identified and quantified selenium hazard, and indicated the steps needed to reduce this hazard to an acceptable level. By utilizing the procedure, NEPA workers can be confident in their ability to understand the risk of aquatic selenium pollution and take appropriate action. Although the procedure was developed for the Forest Service it should also be useful to other federal land management agencies that conduct NEPA assessments, as well as regulatory agencies responsible for issuing coal mining permits under the authority of the Surface Mining Control and Reclamation Act (SMCRA) and associated Section 401 water quality certification under the Clean Water Act. Mining companies will also benefit from the application of this procedure because priority selenium sources can be identified in relation to specific mine operating parameters. The procedure will reveal the point(s) at which there is a need to modify operating

Role of beach morphology in wave overtopping hazard assessment

Science.gov (United States)

Phillips, Benjamin; Brown, Jennifer; Bidlot, Jean-Raymond; Plater, Andrew

2017-04-01

Understanding the role of beach morphology in controlling wave overtopping volume will further minimise uncertainties in flood risk assessments at coastal locations defended by engineered structures worldwide. XBeach is used to model wave overtopping volume for a 1:200 yr joint probability distribution of waves and water levels with measured, pre- and post-storm beach profiles. The simulation with measured bathymetry is repeated with and without morphological evolution enabled during the modelled storm event. This research assesses the role of morphology in controlling wave overtopping volumes for hazardous events that meet the typical design level of coastal defence structures. Results show disabling storm-driven morphology under-represents modelled wave overtopping volumes by up to 39% under high Hs conditions, and has a greater impact on the wave overtopping rate than the variability applied within the boundary conditions due to the range of wave-water level combinations that meet the 1:200 yr joint probability criterion. Accounting for morphology in flood modelling is therefore critical for accurately predicting wave overtopping volumes and the resulting flood hazard and to assess economic losses.

New Multi-HAzard and MulTi-RIsk Assessment MethodS for Europe (MATRIX): A research program towards mitigating multiple hazards and risks in Europe

Science.gov (United States)

Fleming, K. M.; Zschau, J.; Gasparini, P.; Modaressi, H.; Matrix Consortium

2011-12-01

Scientists, engineers, civil protection and disaster managers typically treat natural hazards and risks individually. This leads to the situation where the frequent causal relationships between the different hazards and risks, e.g., earthquakes and volcanos, or floods and landslides, are ignored. Such an oversight may potentially lead to inefficient mitigation planning. As part of their efforts to confront this issue, the European Union, under its FP7 program, is supporting the New Multi-HAzard and MulTi-RIsK Assessment MethodS for Europe or MATRIX project. The focus of MATRIX is on natural hazards, in particular earthquakes, landslides, volcanos, wild fires, storms and fluvial and coastal flooding. MATRIX will endeavour to develop methods and tools to tackle multi-type natural hazards and risks within a common framework, focusing on methodologies that are suited to the European context. The work will involve an assessment of current single-type hazard and risk assessment methodologies, including a comparison and quantification of uncertainties and harmonization of single-type methods, examining the consequence of cascade effects within a multi-hazard environment, time-dependent vulnerability, decision making and support for multi-hazard mitigation and adaption, and a series of test cases. Three test sites are being used to assess the methods developed within the project (Naples, Cologne, and the French West Indies), as well as a "virtual city" based on a comprehensive IT platform that will allow scenarios not represented by the test cases to be examined. In addition, a comprehensive dissemination program that will involve national platforms for disaster management, as well as various outreach activities, will be undertaken. The MATRIX consortium consists of ten research institutions (nine European and one Canadian), an end-user (i.e., one of the European national platforms for disaster reduction) and a partner from industry.

AECB workshop on seismic hazard assessment in Southern Ontario. Recorded proceedings

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-12-31

A workshop on seismic hazard assessment in southern Ontario was conducted on June 19-21, 1995. The purpose of the workshop was to review available geological and seismological data which could affect earthquake occurrence in southern Ontario and to develop a consensus on approaches that should be adopted for characterization of seismic hazard. The workshop was structured in technical sessions to focus presentations and discussions on four technical issues relevant to seismic hazard in southern Ontario, as follows: The importance of geological and geophysical observations for the determination of seismic sources; Methods and approaches which may be adopted for determining seismic sources based on integrated interpretations of geological and seismological information. Methods and data which should be used for characterizing the seismicity parameters of seismic sources. Methods for assessment of vibratory ground motion hazard. This document presents transcripts from recordings made of the presentations and discussion from the workshop. It will be noted, in some sections of the document, that the record is incomplete. This is due in part to recording equipment malfunction and in part due to the poor quality of recording obtained for certain periods.

AECB workshop on seismic hazard assessment in Southern Ontario. Recorded proceedings

International Nuclear Information System (INIS)

1995-01-01

A workshop on seismic hazard assessment in southern Ontario was conducted on June 19-21, 1995. The purpose of the workshop was to review available geological and seismological data which could affect earthquake occurrence in southern Ontario and to develop a consensus on approaches that should be adopted for characterization of seismic hazard. The workshop was structured in technical sessions to focus presentations and discussions on four technical issues relevant to seismic hazard in southern Ontario, as follows: The importance of geological and geophysical observations for the determination of seismic sources; Methods and approaches which may be adopted for determining seismic sources based on integrated interpretations of geological and seismological information. Methods and data which should be used for characterizing the seismicity parameters of seismic sources. Methods for assessment of vibratory ground motion hazard. This document presents transcripts from recordings made of the presentations and discussion from the workshop. It will be noted, in some sections of the document, that the record is incomplete. This is due in part to recording equipment malfunction and in part due to the poor quality of recording obtained for certain periods

In situ assessment of genotoxic hazards of environmental pollution.

Science.gov (United States)

Sandhu, S S; Lower, W R

1989-01-01

The potential impact of the environmental pollutants on human health can be evaluated by the laboratory analysis of the environmental samples or by the measurement of the biological effects on indigenous populations and/or specific test organisms placed in the environment to be monitored. A canary in a cage, used by 19th century miners as a biological indicator for rising levels of toxic gases, is a classical example of in situ hazard identification. The induced toxic effects are often the result of synergistic and antagonistic interactions among various physical and chemical factors that are difficult to reproduce in the laboratory. Therefore, conceivably the biological effects measured on or near the impacted site have greater relevancy for hazard assessment to man than from the data derived from the environmental samples analyzed in the lab. The organisms most commonly employed for the assessment of mutagenicity under real-world conditions are: (1) flowering plants, (2) wild and captive mammals, and (3) aquatic vertebrates. Plant species such as Tradescantia paludosa, Zea mays, and Osmunda regalis have been used for monitoring ambient air quality around several major industrial cities in the U.S.A., nuclear power plants, and industrial waste sites, and also for the assessment of potential health effects of municipal sewage sludges. Domestic animals such as dogs can be used as sentinels to provide information on the effects of contaminants in the environment and have been used to a limited extent to evaluate the environmental influences on the occurrence of breast cancer and osteosarcoma. Cytogenetic analysis from feral and wild animals has been employed for assessing the health hazards and prioritizing the clean-up efforts at hazardous waste sites. Aquatic animals have been used more often than terrestrial animals or plants to identify and characterize the genotoxic effects of environmental pollution. Since 1970, a number of studies has been reported on the

Developing International Guidelines on Volcanic Hazard Assessments for Nuclear Facilities

Science.gov (United States)

Connor, Charles

2014-05-01

Worldwide, tremendous progress has been made in recent decades in forecasting volcanic events, such as episodes of volcanic unrest, eruptions, and the potential impacts of eruptions. Generally these forecasts are divided into two categories. Short-term forecasts are prepared in response to unrest at volcanoes, rely on geophysical monitoring and related observations, and have the goal of forecasting events on timescales of hours to weeks to provide time for evacuation of people, shutdown of facilities, and implementation of related safety measures. Long-term forecasts are prepared to better understand the potential impacts of volcanism in the future and to plan for potential volcanic activity. Long-term forecasts are particularly useful to better understand and communicate the potential consequences of volcanic events for populated areas around volcanoes and for siting critical infrastructure, such as nuclear facilities. Recent work by an international team, through the auspices of the International Atomic Energy Agency, has focused on developing guidelines for long-term volcanic hazard assessments. These guidelines have now been implemented for hazard assessment for nuclear facilities in nations including Indonesia, the Philippines, Armenia, Chile, and the United States. One any time scale, all volcanic hazard assessments rely on a geologically reasonable conceptual model of volcanism. Such conceptual models are usually built upon years or decades of geological studies of specific volcanic systems, analogous systems, and development of a process-level understanding of volcanic activity. Conceptual models are used to bound potential rates of volcanic activity, potential magnitudes of eruptions, and to understand temporal and spatial trends in volcanic activity. It is these conceptual models that provide essential justification for assumptions made in statistical model development and the application of numerical models to generate quantitative forecasts. It is a

Earthquake Hazard Assessment: an Independent Review

Science.gov (United States)

Kossobokov, Vladimir

2016-04-01

Seismic hazard assessment (SHA), from term-less (probabilistic PSHA or deterministic DSHA) to time-dependent (t-DASH) including short-term earthquake forecast/prediction (StEF), is not an easy task that implies a delicate application of statistics to data of limited size and different accuracy. Regretfully, in many cases of SHA, t-DASH, and StEF, the claims of a high potential and efficiency of the methodology are based on a flawed application of statistics and hardly suitable for communication to decision makers. The necessity and possibility of applying the modified tools of Earthquake Prediction Strategies, in particular, the Error Diagram, introduced by G.M. Molchan in early 1990ies for evaluation of SHA, and the Seismic Roulette null-hypothesis as a measure of the alerted space, is evident, and such a testing must be done in advance claiming hazardous areas and/or times. The set of errors, i.e. the rates of failure and of the alerted space-time volume, compared to those obtained in the same number of random guess trials permits evaluating the SHA method effectiveness and determining the optimal choice of the parameters in regard to specified cost-benefit functions. These and other information obtained in such a testing may supply us with a realistic estimate of confidence in SHA results and related recommendations on the level of risks for decision making in regard to engineering design, insurance, and emergency management. These basics of SHA evaluation are exemplified with a few cases of misleading "seismic hazard maps", "precursors", and "forecast/prediction methods".

Environmental Hazards Assessment Program. Quarterly report, July--September 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-10-31

This report describes activities and reports on progress for the first quarter (July--September) of the fourth year of the grant to support the Environmental Hazards Assessment Program (EHAP) at the Medical University of South Carolina. It reports progress against the grant objectives and the Program Implementation Plan published at the end of the first year of the grant. The objectives of EHAP stated in the proposal to DOE are to: (1) develop a holistic, national basis for risk assessment, risk management, and risk communication that recognizes the direct impact of environmental hazards on the health and well-being of all; (2) develop a pool of talented scientists and experts in cleanup activities, especially in human health aspects; and (3) identify needs and develop programs addressing the critical shortage of well-educated, highly-skilled technical and scientific personnel to address the health-oriented aspects of environmental restoration and waste management.

External hazards in reliability and risk assessment of nuclear power plants

International Nuclear Information System (INIS)

Stevenson, J.D.

1977-01-01

It is current practice in the design of nuclear power generating stations to protect against the effects of significant natural and man-made external hazards which can occur at the plant site in excess of those hazards normally considered for conventional facilities. This paper is meant to identify those postulated external hazards typically considered in nuclear facility design. The paper also attempts to fulfill the following four objectives: (1) Define the current state of the art in applying reliability and risk analysis to determine external hazard design requirements. (2) Provide a ready source of literature references applicable to probabilistic design for extreme loads. (3) Provide some quantitative probability assessment estimates of external hazards. (4) Develop exclusion criteria by which postulated external hazards can be eliminated as a design basis. Rigorous evaluation of the design requirements for nuclear power plant facilities based on principles of probability and risk analysis is just beginning. It is hoped these techniques will be used more extensively in the future to provide a more rational basis for developing design requirements. (orig.) [de

Distance education course on spatial multi-hazard risk assessment, using Open Source software

Science.gov (United States)

van Westen, C. J.; Frigerio, S.

2009-04-01

As part of the capacity building activities of the United Nations University - ITC School on Disaster Geo-Information Management (UNU-ITC DGIM) the International Institute for Geoinformation Science and Earth Observation (ITC) has developed a distance education course on the application of Geographic Information Systems for multi-hazard risk assessment. This course is designed for academic staff, as well as for professionals working in (non-) governmental organizations where knowledge of disaster risk management is essential. The course guides the participants through the entire process of risk assessment, on the basis of a case study of a city exposed to multiple hazards, in a developing country. The courses consists of eight modules, each with a guide book explaining the theoretical background, and guiding the participants through spatial data requirements for risk assessment, hazard assessment procedures, generation of elements at risk databases, vulnerability assessment, qualitative and quantitative risk assessment methods, risk evaluation and risk reduction. Linked to the theory is a large set of exercises, with exercise descriptions, answer sheets, demos and GIS data. The exercises deal with four different types of hazards: earthquakes, flooding, technological hazards, and landslides. One important consideration in designing the course is that people from developing countries should not be restricted in using it due to financial burdens for software acquisition. Therefore the aim was to use Open Source software as a basis. The GIS exercises are written for the ILWIS software. All exercises have also been integrated into a WebGIS, using the Open source software CartoWeb (based on GNU License). It is modular and customizable thanks to its object-oriented architecture and based on a hierarchical structure (to manage and organize every package of information of every step required in risk assessment). Different switches for every component of the risk assessment

Multi-hazard risk assessment of the Republic of Mauritius

Science.gov (United States)

Mysiak, Jaroslav; Galli, Alberto; Amadio, Mattia; Teatini, Chiara

2013-04-01

The Republic of Mauritius (ROM) is a small island developing state (SIDS), part of the Mascarene Islands in West Indian Ocean, comprised by Mauritius, Rodrigues, Agalega and St. Brandon islands and several islets. ROM is exposed to many natural hazards notably cyclones, tsunamis, torrential precipitation, landslides, and droughts; and highly vulnerable sea level rise (SLR) driven by human induced climate change. The multihazard risk assessment presented in this paper is aimed at identifying the areas prone to flood, inundation and landslide hazard, and inform the development of strategy for disaster risk reduction (DRR) and climate change adaptation (CCA). Climate risk analysis - a central component of the analysis - is one of the first comprehensive climate modelling studies conducted for the country. Climate change may lift the temperature by 1-2 degree Celsius by 2060-2070, and increase sizably the intensity and frequency of extreme precipitation events. According to the IPCC Forth Assessment Report (AR4), the expected Sea Level Rise (SLR) ranges between 16 and 49 cm. Individually or in combination, the inland flood, coastal inundation and landslide hazards affect large proportion of the country. Sea level rise and the changes in precipitation regimes will amplified existing vulnerabilities and create new ones. The paper outlines an Action plan for Disaster Risk Reduction that takes into account the likely effects of climate change. The Action Plan calls on the government to establish a National Platform for Disaster Risk Reduction as recommended by the Hyogo Framework for Action (HFA) 2005-2015. It consists of nine recommendations which, if put in practice, will significantly reduce the annual damage to natural hazard and produce additional (ancillary) benefits in economic, social and environmental terms.

Benefits Assessment of Two California Hazardous Waste Disposal Facilities (1983)

Science.gov (United States)

The purpose of this study was to assess the benefits of RCRA regulations, comparing the results before and after new regulations at two existing hazardous waste sites previously regulated under California state law

Comparative risk assessments for Guadeloupe: earthquakes and storm surge

OpenAIRE

Réveillère , Arnaud; Monfort , Daniel; Lecacheux , Sophie; Grisanti , Ludovic; Muller , Héloise; Bertil , Didier; Rohmer , Jérémy; Sedan , Olivier; Douglas , John; Baills , Audrey; Modaressi , Hormoz

2012-01-01

In France, risk assessments for natural hazards are usually carried out separately and decision makers lack comprehensive information. Moreover, since the cause of the hazard (e.g. meteorological, geological) and the physical phenomenon that causes damage (e.g. inundation, ground shaking) may be fundamentally different, the quantitative comparison of single risk assessments that were not conducted in a compatible framework is not straightforward. Comprehensive comparative risk assessments exi...

An Overview of GIS-Based Modeling and Assessment of Mining-Induced Hazards: Soil, Water, and Forest.

Science.gov (United States)

Suh, Jangwon; Kim, Sung-Min; Yi, Huiuk; Choi, Yosoon

2017-11-27

In this study, current geographic information system (GIS)-based methods and their application for the modeling and assessment of mining-induced hazards were reviewed. Various types of mining-induced hazard, including soil contamination, soil erosion, water pollution, and deforestation were considered in the discussion of the strength and role of GIS as a viable problem-solving tool in relation to mining-induced hazards. The various types of mining-induced hazard were classified into two or three subtopics according to the steps involved in the reclamation procedure, or elements of the hazard of interest. Because GIS is appropriated for the handling of geospatial data in relation to mining-induced hazards, the application and feasibility of exploiting GIS-based modeling and assessment of mining-induced hazards within the mining industry could be expanded further.

An Overview of GIS-Based Modeling and Assessment of Mining-Induced Hazards: Soil, Water, and Forest

Science.gov (United States)

Kim, Sung-Min; Yi, Huiuk; Choi, Yosoon

2017-01-01

In this study, current geographic information system (GIS)-based methods and their application for the modeling and assessment of mining-induced hazards were reviewed. Various types of mining-induced hazard, including soil contamination, soil erosion, water pollution, and deforestation were considered in the discussion of the strength and role of GIS as a viable problem-solving tool in relation to mining-induced hazards. The various types of mining-induced hazard were classified into two or three subtopics according to the steps involved in the reclamation procedure, or elements of the hazard of interest. Because GIS is appropriated for the handling of geospatial data in relation to mining-induced hazards, the application and feasibility of exploiting GIS-based modeling and assessment of mining-induced hazards within the mining industry could be expanded further. PMID:29186922

An Overview of GIS-Based Modeling and Assessment of Mining-Induced Hazards: Soil, Water, and Forest

Directory of Open Access Journals (Sweden)

Jangwon Suh

2017-11-01

Full Text Available In this study, current geographic information system (GIS-based methods and their application for the modeling and assessment of mining-induced hazards were reviewed. Various types of mining-induced hazard, including soil contamination, soil erosion, water pollution, and deforestation were considered in the discussion of the strength and role of GIS as a viable problem-solving tool in relation to mining-induced hazards. The various types of mining-induced hazard were classified into two or three subtopics according to the steps involved in the reclamation procedure, or elements of the hazard of interest. Because GIS is appropriated for the handling of geospatial data in relation to mining-induced hazards, the application and feasibility of exploiting GIS-based modeling and assessment of mining-induced hazards within the mining industry could be expanded further.

Ecotoxicological, ecophysiological, and biogeochemical fundamentals of risk assessment

International Nuclear Information System (INIS)

Bashkin, V.N.; Kozlov, M.Ya.; Evstafjeva, E.V.

1993-01-01

Risk assessment (RA) influenced by different factors in radionuclide polluted regions is carried out by determining the biogeochemical structure of a region. Consequently, ecological-biogeochemical regionalization, ecotoxicological and ecophysiological monitoring of human population health are the important approach to RA. These criteria should conjugate with LCA of various industrial and agricultural products. Given fundamentals and approaches are needed for areas where traditional pollutants (heavy metals, pesticides, fertilizers, POPs etc) are enforced sharply by radioactive pollution. For RA of these complex pollutants, the methods of human adaptability to a polluted environment have been carried out. These techniques include biogeochemical, ecotoxicological, and ecophysiological analyses of risk factors as well as quantitative analysis of uncertainties using expert-modeling systems. Furthermore, the modern statistical methods are used for quantitative assessment of human adaptability to radioactive and nonradioactive pollutants. The results obtained in Chernobyl regions show the acceptability of these methods for risk assessment

A systematic assessment of the state of hazardous waste clean-up technologies

International Nuclear Information System (INIS)

Berg, M.T.; Reed, B.E.; Gabr, M.

1993-07-01

West Virginia University (WVU) and the US DOE Morgantown Energy Technology Center (METC) entered into a Cooperative Agreement on August 29, 1992 entitled ''Decontamination Systems Information and Research Programs.'' Stipulated within the Agreement is the requirement that WVU submit to METC a series of Technical Progress Report for Year 1 of the Agreement. This report reflects the progress and/or efforts performed on the following nine technical projects encompassed by the Year 1 Agreement for the period of April 1 through June 30, 1993: Systematic assessment of the state of hazardous waste clean-up technologies; site remediation technologies -- drain-enhanced soil flushing (DESF) for organic contaminants removal; site remediation technologies -- in situ bioremediation of organic contaminants; excavation systems for hazardous waste sites; chemical destruction of polychlorinated biphenyls; development of organic sensors -- monolayer and multilayer self-assembled films for chemical sensors; Winfield lock and dam remediation; Assessments of Technologies for hazardous waste site remediation -- non-treatment technologies and pilot scale test facility implementation; and remediation of hazardous sites with stream reforming

Scenario-based earthquake hazard and risk assessment for Baku (Azerbaijan

Directory of Open Access Journals (Sweden)

G. Babayev

2010-12-01

Full Text Available A rapid growth of population, intensive civil and industrial building, land and water instabilities (e.g. landslides, significant underground water level fluctuations, and the lack of public awareness regarding seismic hazard contribute to the increase of vulnerability of Baku (the capital city of the Republic of Azerbaijan to earthquakes. In this study, we assess an earthquake risk in the city determined as a convolution of seismic hazard (in terms of the surface peak ground acceleration, PGA, vulnerability (due to building construction fragility, population features, the gross domestic product per capita, and landslide's occurrence, and exposure of infrastructure and critical facilities. The earthquake risk assessment provides useful information to identify the factors influencing the risk. A deterministic seismic hazard for Baku is analysed for four earthquake scenarios: near, far, local, and extreme events. The seismic hazard models demonstrate the level of ground shaking in the city: PGA high values are predicted in the southern coastal and north-eastern parts of the city and in some parts of the downtown. The PGA attains its maximal values for the local and extreme earthquake scenarios. We show that the quality of buildings and the probability of their damage, the distribution of urban population, exposure, and the pattern of peak ground acceleration contribute to the seismic risk, meanwhile the vulnerability factors play a more prominent role for all earthquake scenarios. Our results can allow elaborating strategic countermeasure plans for the earthquake risk mitigation in the Baku city.

Seismic rupture modelling, strong motion prediction and seismic hazard assessment: fundamental and applied approaches; Modelisation de la rupture sismique, prediction du mouvement fort, et evaluation de l'alea sismique: approches fondamentale et appliquee

Energy Technology Data Exchange (ETDEWEB)

Berge-Thierry, C

2007-05-15

The defence to obtain the 'Habilitation a Diriger des Recherches' is a synthesis of the research work performed since the end of my Ph D. thesis in 1997. This synthesis covers the two years as post doctoral researcher at the Bureau d'Evaluation des Risques Sismiques at the Institut de Protection (BERSSIN), and the seven consecutive years as seismologist and head of the BERSSIN team. This work and the research project are presented in the framework of the seismic risk topic, and particularly with respect to the seismic hazard assessment. Seismic risk combines seismic hazard and vulnerability. Vulnerability combines the strength of building structures and the human and economical consequences in case of structural failure. Seismic hazard is usually defined in terms of plausible seismic motion (soil acceleration or velocity) in a site for a given time period. Either for the regulatory context or the structural specificity (conventional structure or high risk construction), seismic hazard assessment needs: to identify and locate the seismic sources (zones or faults), to characterize their activity, to evaluate the seismic motion to which the structure has to resist (including the site effects). I specialized in the field of numerical strong-motion prediction using high frequency seismic sources modelling and forming part of the IRSN allowed me to rapidly working on the different tasks of seismic hazard assessment. Thanks to the expertise practice and the participation to the regulation evolution (nuclear power plants, conventional and chemical structures), I have been able to work on empirical strong-motion prediction, including site effects. Specific questions related to the interface between seismologists and structural engineers are also presented, especially the quantification of uncertainties. This is part of the research work initiated to improve the selection of the input ground motion in designing or verifying the stability of structures. (author)

Integrated Risk Assessment to Natural Hazards in Motozintla, Chiapas, Mexico

Science.gov (United States)

Novelo-Casanova, D. A.

2012-12-01

An integrated risk assessment includes the analysis of all components of individual constituents of risk such as baseline study, hazard identification and categorization, hazard exposure, and vulnerability. Vulnerability refers to the inability of people, organizations, and societies to withstand adverse impacts from multiple stressors to which they are exposed. These impacts are due to characteristics inherent in social interactions, institutions, and systems of cultural values. Thus, social vulnerability is a pre-existing condition that affects a society's ability to prepare for and recover from a disruptive event. Risk is the probability of a loss, and this loss depends on three elements: hazard, exposure, and vulnerability. Thus, risk is the estimated impact that a hazard event would have on people, services, facilities, structures and assets in a community. In this work we assess the risk to natural hazards in the community of Motozintla located in southern Mexico in the state of Chiapas (15.37N, 92.25W) with a population of about 20 000 habitants. Due to its geographical and geological location, this community is continuously exposed to many different natural hazards (earthquakes, landslides, volcanic eruptions, and floods). To determine the level of exposure of the community to natural hazards, we developed integrated studies and analysis of seismic microzonation, landslide and flood susceptibility as well as volcanic impact using standard methodologies. Social vulnerability was quantified from data obtained from local families interviews. Five variables were considered: household structure quality and design, availability of basic public services, family economic conditions, existing family plans for disaster preparedness, and risk perception.The number of families surveyed was determined considering a sample statistically significant. The families that were interviewed were selected using the simple random sampling technique with replacement. With these

Assessment of fire hazards in buildings housing fusion energy experiments

International Nuclear Information System (INIS)

Alvares, N.; Lipska, A.

1978-01-01

A number of materials in and within the proximity of buildings housing fusion energy experiments (FEE) were analyzed for their potential fire hazard. The materials used in this study were mostly: electrical and thermal insulations. The fire hazard of these materials was assessed in terms of their ease of ignition, heat release rate, generation of smoke, and the effect of thermal environment on the combustion behavior. Several fire protection measures for buildings housing the (FEE) projects are analyzed and as a result of this study are found to be adequate for the near term

Hazard classification or risk assessment

DEFF Research Database (Denmark)

Hass, Ulla

2013-01-01

The EU classification of substances for e.g. reproductive toxicants is hazard based and does not to address the risk suchsubstances may pose through normal, or extreme, use. Such hazard classification complies with the consumer's right to know. It is also an incentive to careful use and storage...

Landslide hazard in Bukavu (DR Congo): a geomorphological assessment in a data-poor context

Science.gov (United States)

Dewitte, Olivier; Mugaruka Bibentyo, Toussaint; Kulimushi Matabaro, Sylvain; Balegamire, Clarisse; Basimike, Joseph; Delvaux, Damien; Dille, Antoine; Ganza Bamulezi, Gloire; Jacobs, Liesbet; Michellier, Caroline; Monsieurs, Elise; Mugisho Birhenjira, Espoir; Nshokano, Jean-Robert; Nzolang, Charles; Kervyn, François

2017-04-01

Many cities in the Global South are known for facing an important increase in their population size. Many of them are then struggling with the sprawl of new settlements and very often urban planning and sustainable management policies are limited, if not non-existent. When those cities are set in landslide-prone environments, this situation is even more problematic. Despite these environmental constrains, landslide hazard assessments relevant for landscape planning remain rare. The objective of this research is to assess the landslide hazard in Bukavu, a city in DR Congo that is facing such a situation. We used a geomorphological approach (adapted from Cardinali et al., 2002) taking into account the data-poor context and the impact of anthropogenic activities. First, we built a multi-temporal historical inventory for a period of 60 years. A total of 151 landslides were mapped (largest landslide 1.5 km2). Their cumulative areas cover 29% of the urban territory and several types of processes are identified. Changes in the distribution and pattern of landslides allowed then to infer the possible evolution of the slopes, the most probable type of failures, and their expected frequency of occurrence and intensity. Despite this comprehensive inventory, hazard linked to the occurrence of new large deep-seated slides cannot be assessed due a scarcity of reliable data on the environmental factors controlling their occurrence. In addition, age estimation of the occurrence of some of the largest landslides refers to periods at the beginning of the Holocene where climatic and seismic conditions were probably different. Therefore, based on the inventory, we propose four hazard scenarios that coincide with today's environment. Hazard assessment was done for (1) reactivation of deep-seated slides, (2) occurrence of new small shallow slides, (3) rock falls, and (4) movements within existing landslides. Based on these assessments, we produced four hazard maps that indicate the

Generic framework for meso-scale assessment of climate change hazards in coastal environments

DEFF Research Database (Denmark)

Appelquist, Lars Rosendahl

2013-01-01

coastal environments worldwide through a specially designed coastal classification system containing 113 generic coastal types. The framework provides information on the degree to which key climate change hazards are inherent in a particular coastal environment, and covers the hazards of ecosystem......This paper presents a generic framework for assessing inherent climate change hazards in coastal environments through a combined coastal classification and hazard evaluation system. The framework is developed to be used at scales relevant for regional and national planning and aims to cover all...... and computing requirements, allowing for application in developing country settings. It is presented as a graphical tool—the Coastal Hazard Wheel—to ease its application for planning purposes....

The hostel or the warehouse? Spatiotemporal exposure assessment for natural hazards

Science.gov (United States)

Fuchs, S.; Keiler, M.; Zischg, A.

2015-04-01

A spatially explicit object-based temporal assessment of buildings and citizens exposed to natural hazards in Austria is presented, including elements at risk to river flooding, torrential flooding, and snow avalanches. It is shown that the repeatedly-stated assumption of increasing losses due to continued population growth and related increase in assets has to be opposed to the local development of building stock. While some regions have shown a clearly above-average increase in assets, other regions were characterised by a below-average development. This mirrors the topography of the country, but also the different economic activities. While hotels and hostels are extraordinary prone to mountain hazards, commercial buildings as well as buildings used for recreation purpose are considerably exposed to river flooding. Residential buildings have shown an average exposure, compared to the amount of buildings of this type in the overall building stock. In sum, around 5% of all buildings are exposed to mountain hazards, and around 9% to river flooding, with around 1% of the buildings stock being multi-exposed. It is shown that the dynamics of elements at risk exposed have a time lag once land use regulations are enforced, and it is concluded that an object-based assessment has clear advantages compared to the assessment using aggregated land use data.

Application of a new methodology for coastal multi-hazard-assessment and management on the state of Karnataka, India

DEFF Research Database (Denmark)

Appelquist, Lars Rosendahl; Balstrom, Thomas

2015-01-01

This paper presents the application of a new Methodology for coastal multi-hazard assessment & management under a changing global climate on the state of Karnataka, India. The recently published methodology termed the Coastal Hazard Wheel (CHW) is designed for local, regional and national hazard...... at a scale relevant for regional planning purposes. It uses a GIS approach to develop regional and sub-regional hazard maps as well as to produce relevant hazard risk data, and includes a discussion of uncertainties, limitations and management perspectives. The hazard assessment shows that 61 percent...

Transparent Global Seismic Hazard and Risk Assessment

Science.gov (United States)

Smolka, Anselm; Schneider, John; Pinho, Rui; Crowley, Helen

2013-04-01

Vulnerability to earthquakes is increasing, yet advanced reliable risk assessment tools and data are inaccessible to most, despite being a critical basis for managing risk. Also, there are few, if any, global standards that allow us to compare risk between various locations. The Global Earthquake Model (GEM) is a unique collaborative effort that aims to provide organizations and individuals with tools and resources for transparent assessment of earthquake risk anywhere in the world. By pooling data, knowledge and people, GEM acts as an international forum for collaboration and exchange, and leverages the knowledge of leading experts for the benefit of society. Sharing of data and risk information, best practices, and approaches across the globe is key to assessing risk more effectively. Through global projects, open-source IT development and collaborations with more than 10 regions, leading experts are collaboratively developing unique global datasets, best practice, open tools and models for seismic hazard and risk assessment. Guided by the needs and experiences of governments, companies and citizens at large, they work in continuous interaction with the wider community. A continuously expanding public-private partnership constitutes the GEM Foundation, which drives the collaborative GEM effort. An integrated and holistic approach to risk is key to GEM's risk assessment platform, OpenQuake, that integrates all above-mentioned contributions and will become available towards the end of 2014. Stakeholders worldwide will be able to calculate, visualise and investigate earthquake risk, capture new data and to share their findings for joint learning. Homogenized information on hazard can be combined with data on exposure (buildings, population) and data on their vulnerability, for loss assessment around the globe. Furthermore, for a true integrated view of seismic risk, users can add social vulnerability and resilience indices to maps and estimate the costs and benefits

Environmental Hazards Assessment Program. Quarterly report, July 1994--September 1994

International Nuclear Information System (INIS)

1994-01-01

The objectives of the Environmental Hazards Assessment Program (EHAP) stated in the proposal to DOE are as follows: Development of a holistic, national basis for risk assessment, risk management, and risk communication that recognizes the direct impact of environmental hazards on the health and well-being of all; development of a pool of talented scientist and experts in cleanup activities, especially in human health aspects; identification of needs and development of programs addressing the critical shortage of well-educated, highly-skilled technical and scientific personnel to address the health oriented aspects of environmental restoration and waste management. This is a progress report of the first quarter of the third year of the grant. It reports progress against these grant objectives and the Program Implementation Plan (published at the end of the first year of the grant)

Tsunami hazard assessment on nuclear power plant site evaluation accordance on DS 417

International Nuclear Information System (INIS)

Akhmad Khusyairi

2011-01-01

Nuclear power plant site evaluation should conduct the hazard evaluation on tsunami. Global climate changes and particularly extreme meteorology and hydrology phenomena have an impact on the structure, systems and important components related to safety. Therefore, IAEA makes efforts to revise the IAEA Safety Standard Series NS-G 3.4, Meteorological Events in Site Evaluation for Nuclear Power Plants and IAEA safety standard series NS-G 3.5 Flood Hazard For Nuclear Power Plants On Coastal And River Sites, in order to provide protection against the public and the environment safety due to operation of nuclear power plants. There are two methods used in assessing tsunami hazard, probabilistic and deterministic methods. In the tsunami hazard assessment, some necessary information and data should be obtained to determine the basic design of tsunami hazard during designing nuclear power plants, especially the cooling system design. Flooding caused tsunami must be evaluated to determine the site protection system. Furthermore, There must be an evaluation on either coincident event or meteorological simultaneously tsunami event that caused the worst effect on the site. Therefore, the protection of the site from extreme tsunami can be planned. (author)

Climate Prediction Center(CPC)Global Tropics Hazards and Benefits Assessment

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Global Tropics Hazards and Benefits Assessment (GTH) is an outlook product for the areas in the Tropics. Forecasts for the Week-1 and Week-2 period are given for...

Assessment and management of cancer risks from radiological and chemical hazards

International Nuclear Information System (INIS)

1998-01-01

A Joint Working Group was established in April 1995 by the President of the Atomic Energy Control Board (AECB) and the Assistant Deputy Minister of the Health Protection Branch of Health Canada to examine the similarities, disparities and inconsistencies between the levels of risk considered acceptable for regulating ionizing radiation and those considered acceptable for regulating chemical and microbiological hazards. During the process of collecting, analysing and interpreting information, the Joint Working Group realized that its terms of reference as written presented a major difficulty because of the lack of consensus on acceptable levels of risk. Consequently it decided that the most reasonable way to proceed was to compare the risk assessment and management processes used to protect the public from radiation, chemicals and microbiological hazards. This report concentrates on the assessment and management of ionizing radiation and genotoxic chemicals (which both cause cancer by damaging the DNA in cells) and pays less attention to non-genotoxic effects and microbiological hazards. The report also examines public more than occupational exposures and exposures from man-made rather than naturally occurring agents. (author)

Seismic hazard assessment in the Catania and Siracusa urban areas (Italy) through different approaches

Science.gov (United States)

Panzera, Francesco; Lombardo, Giuseppe; Rigano, Rosaria

2010-05-01

The seismic hazard assessment (SHA) can be performed using either Deterministic or Probabilistic approaches. In present study a probabilistic analysis was carried out for the Catania and Siracusa towns using two different procedures: the 'site' (Albarello and Mucciarelli, 2002) and the 'seismotectonic' (Cornell 1968; Esteva, 1967) methodologies. The SASHA code (D'Amico and Albarello, 2007) was used to calculate seismic hazard through the 'site' approach, whereas the CRISIS2007 code (Ordaz et al., 2007) was adopted in the Esteva-Cornell procedure. According to current international conventions for PSHA (SSHAC, 1997), a logic tree approach was followed to consider and reduce the epistemic uncertainties, for both seismotectonic and site methods. The code SASHA handles the intensity data taking into account the macroseismic information of past earthquakes. CRISIS2007 code needs, as input elements, a seismic catalogue tested for completeness, a seismogenetic zonation and ground motion predicting equations. Data concerning the characterization of regional seismic sources and ground motion attenuation properties were taken from the literature. Special care was devoted to define source zone models, taking into account the most recent studies on regional seismotectonic features and, in particular, the possibility of considering the Malta escarpment as a potential source. The combined use of the above mentioned approaches allowed us to obtain useful elements to define the site seismic hazard in Catania and Siracusa. The results point out that the choice of the probabilistic model plays a fundamental role. It is indeed observed that when the site intensity data are used, the town of Catania shows hazard values higher than the ones found for Siracusa, for each considered return period. On the contrary, when the Esteva-Cornell method is used, Siracusa urban area shows higher hazard than Catania, for return periods greater than one hundred years. The higher hazard observed

SHC, Seismic Hazard Assessment for Eastern US

International Nuclear Information System (INIS)

Savy, J.; Davis, B.

2001-01-01

1 - Description of program or function: SHC was developed as part of the Eastern United States (EUS) Seismic Hazard Characterization (SHC) Project to design an SHC methodology for the region east of the Rocky Mountains in a form suitable for probabilistic risk assessment and to apply that methodology to 69 site locations, some of them with local soil conditions. The method developed uses expert opinions to obtain the input to the analysis. SHC contains four modules which calculate the seismic hazard at a site located in a region of diffuse seismicity, where the seismicity is modeled by area sources. SHC integrates the opinions of 11 seismicity and five ground-motion experts. The PRDS model generates the discrete probability density function of the distances to the site for the various seismic source zones. These probability distributions are used by the COMAP module to generate the set of all alternative maps and the discrete probability density of the seismic zonation maps for each expert. The third module, ALEAS, uses these maps and their weights to calculate the best estimate and constant percentile hazard distribution resulting from the choice of a given seismicity expert for all ground-motion experts. This module can be used alone to perform a seismic hazard analysis as well as in conjunction with the other modules. The fourth module, COMB, combines the best- estimate and constant-percentile hazard over all seismicity experts, using the set of weights calculated by ALEAS, to produce the final probability distribution of the hazard for the site under consideration so that the hazard analysis can be performed for any location in the EUS. Local geological-site characteristics are incorporated in a generic fashion, and the data are developed in a generic manner. 2 - Method of solution: SHC uses a seismic-source approach utilizing statistical and geological evidence to define geographical regions with homogeneous Poisson activity throughout the zone, described by a

Ecotoxicological hazard assessment of hydrocarbon contaminated soils: A case study

International Nuclear Information System (INIS)

Roy, Y.; Pauwels, S.J.; Chasse, R.

1994-01-01

The Ecotoxicological Hazard Assessment (EHA) developed by the Quebec Ministry of Environment and Wildlife was used as part of the management scheme of contaminated soils from a former refinery. The study consists of assessing five types of soils (reference, heavily contaminated, slightly contaminated, thermally-treated, and biotreated) to determine their relative intrinsic hazard. During the exploratory activities a series of ten assessment endpoints where identified to support this typical EHA. During SOURCE characterization, the physicochemical make-up of the soils is described and the presence and concentrations of priority pollutants is determined. During FATE characterization, the potential for bioconcentration, mobility, and persistence of pollutants is determined. During EFFECTS characterization, the soils and their leachates are tested using standard terrestrial and aquatic bioassays. The data from the toxicological and analytical testing program are evaluated semi-quantitatively on the basis of a scoring system developed by consensus. The discussion will highlight how data are used within an EHA to streamline the decision-making process regarding the follow-up cleanup and disposal of contaminated soils

Scenario for a Short-Term Probabilistic Seismic Hazard Assessment (PSHA in Chiayi, Taiwan

Directory of Open Access Journals (Sweden)

Chung-Han Chan

2013-01-01

Full Text Available Using seismic activity and the Meishan earthquake sequence that occurred from 1904 to 1906, a scenario for short-term probabilistic seismic hazards in the Chiayi region of Taiwan is assessed. The long-term earthquake occurrence rate in Taiwan was evaluated using a smoothing kernel. The highest seismicity rate was calculated around the Chiayi region. To consider earthquake interactions, the rate-and-state friction model was introduced to estimate the seismicity rate evolution due to the Coulomb stress change. As imparted by the 1904 Touliu earthquake, stress changes near the 1906 Meishan and Yangshuigang epicenters was higher than the magnitude of tidal triggering. With regard to the impact of the Meishan earthquake, the region close to the Yangshuigang earthquake epicenter had a +0.75 bar stress increase. The results indicated significant interaction between the three damage events. Considering the path and site effect using ground motion prediction equations, a probabilistic seismic hazard in the form of a hazard evolution and a hazard map was assessed. A significant elevation in hazards following the three earthquakes in the sequence was determined. The results illustrate a possible scenario for seismic hazards in the Chiayi region which may take place repeatly in the future. Such scenario provides essential information on earthquake preparation, devastation estimations, emergency sheltering, utility restoration, and structure reconstruction.

Landslides in Nicaragua - Mapping, Inventory, Hazard Assessment, Vulnerability Reduction, and Forecasting Attempts

Science.gov (United States)

Dévoli, G.; Strauch, W.; Álvarez, A.; Muñoz, A.; Kjekstad, O.

2009-04-01

A successful landslide hazard and risk assessment requires awareness and good understanding of the potential landslide problems within the geographic area involved. However, this requirement is not always met in developing countries where population, scientific community, and the government may not be aware of the landslide threat. The landslide hazard assessment is often neglected or is based on sparse and not well documented technical information. In Nicaragua (Central America), the basic conditions for landslide hazard and risk assessment were first created after the catastrophic landslides triggered by Hurricane Mitch in October 1998. A single landslide took the life of thousands of people at Casita volcano forcing entire communities to be evacuated or relocated and, furthermore, thousands of smaller landslides caused loss of fertile soils and pasture lands, and made serious damages to the infrastructure. Since those events occurred, the public awareness has increased and the country relies now on new local and national governmental laws and policies, on a number of landslide investigations, and on educational and training programs. Dozens of geologists have been capacitated to investigate landslide prone areas, The Instituto Nicaragüense de Estudios Territoriales (INETER), governmental geo-scientific institution, has assumed the responsibility to help land-use planners and public officials to reduce geological hazard losses. They are committed to work cooperatively with national, international, and local agencies, universities and the private sector to provide scientific information and improve public safety through forecasting and warnings. However, in order to provide successful long-term landslide hazard assessment, the institutions must face challenges related to the scarcity and varied quality of available landslide information; collection and access to dispersed data and documents; organization of landslide information in a form that can be easy to

Assessing the risk posed by natural hazards to infrastructures

Science.gov (United States)

Eidsvig, Unni Marie K.; Kristensen, Krister; Vidar Vangelsten, Bjørn

2017-03-01

This paper proposes a model for assessing the risk posed by natural hazards to infrastructures, with a focus on the indirect losses and loss of stability for the population relying on the infrastructure. The model prescribes a three-level analysis with increasing level of detail, moving from qualitative to quantitative analysis. The focus is on a methodology for semi-quantitative analyses to be performed at the second level. The purpose of this type of analysis is to perform a screening of the scenarios of natural hazards threatening the infrastructures, identifying the most critical scenarios and investigating the need for further analyses (third level). The proposed semi-quantitative methodology considers the frequency of the natural hazard, different aspects of vulnerability, including the physical vulnerability of the infrastructure itself, and the societal dependency on the infrastructure. An indicator-based approach is applied, ranking the indicators on a relative scale according to pre-defined ranking criteria. The proposed indicators, which characterise conditions that influence the probability of an infrastructure malfunctioning caused by a natural event, are defined as (1) robustness and buffer capacity, (2) level of protection, (3) quality/level of maintenance and renewal, (4) adaptability and quality of operational procedures and (5) transparency/complexity/degree of coupling. Further indicators describe conditions influencing the socio-economic consequences of the infrastructure malfunctioning, such as (1) redundancy and/or substitution, (2) cascading effects and dependencies, (3) preparedness and (4) early warning, emergency response and measures. The aggregated risk estimate is a combination of the semi-quantitative vulnerability indicators, as well as quantitative estimates of the frequency of the natural hazard, the potential duration of the infrastructure malfunctioning (e.g. depending on the required restoration effort) and the number of users of

Seismic rupture modelling, strong motion prediction and seismic hazard assessment: fundamental and applied approaches; Modelisation de la rupture sismique, prediction du mouvement fort, et evaluation de l'alea sismique: approches fondamentale et appliquee

Energy Technology Data Exchange (ETDEWEB)

Berge-Thierry, C

2007-05-15

The defence to obtain the 'Habilitation a Diriger des Recherches' is a synthesis of the research work performed since the end of my Ph D. thesis in 1997. This synthesis covers the two years as post doctoral researcher at the Bureau d'Evaluation des Risques Sismiques at the Institut de Protection (BERSSIN), and the seven consecutive years as seismologist and head of the BERSSIN team. This work and the research project are presented in the framework of the seismic risk topic, and particularly with respect to the seismic hazard assessment. Seismic risk combines seismic hazard and vulnerability. Vulnerability combines the strength of building structures and the human and economical consequences in case of structural failure. Seismic hazard is usually defined in terms of plausible seismic motion (soil acceleration or velocity) in a site for a given time period. Either for the regulatory context or the structural specificity (conventional structure or high risk construction), seismic hazard assessment needs: to identify and locate the seismic sources (zones or faults), to characterize their activity, to evaluate the seismic motion to which the structure has to resist (including the site effects). I specialized in the field of numerical strong-motion prediction using high frequency seismic sources modelling and forming part of the IRSN allowed me to rapidly working on the different tasks of seismic hazard assessment. Thanks to the expertise practice and the participation to the regulation evolution (nuclear power plants, conventional and chemical structures), I have been able to work on empirical strong-motion prediction, including site effects. Specific questions related to the interface between seismologists and structural engineers are also presented, especially the quantification of uncertainties. This is part of the research work initiated to improve the selection of the input ground motion in designing or verifying the stability of structures. (author)

Introduction: Hazard mapping

Science.gov (United States)

Baum, Rex L.; Miyagi, Toyohiko; Lee, Saro; Trofymchuk, Oleksandr M

2014-01-01

Twenty papers were accepted into the session on landslide hazard mapping for oral presentation. The papers presented susceptibility and hazard analysis based on approaches ranging from field-based assessments to statistically based models to assessments that combined hydromechanical and probabilistic components. Many of the studies have taken advantage of increasing availability of remotely sensed data and nearly all relied on Geographic Information Systems to organize and analyze spatial data. The studies used a range of methods for assessing performance and validating hazard and susceptibility models. A few of the studies presented in this session also included some element of landslide risk assessment. This collection of papers clearly demonstrates that a wide range of approaches can lead to useful assessments of landslide susceptibility and hazard.

Environmental Hazards Assessment Program quarterly report, January--March 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-04-30

The objectives of the Environmental Hazards Assessment Program (EHAP) stated in the proposal to DOE are to: develop a holistic, national basis for risk assessment, risk management, and risk communication that recognizes the direct impact of environmental hazards on the health and well-being of all; develop a pool of talented scientists and experts in cleanup activities, especially in human health aspects; and identify needs and develop programs addressing the critical shortage of well-educated, highly-skilled technical and scientific personnel to address the health oriented aspects of environmental restoration and waste management. This report describes activities and reports on progress for the third quarter (January--March) of the third year of the grant. It reports progress against these grant objectives and the Program Implementation Plan published at the end of the first year of the grant. Questions, comments, or requests for further information concerning the activities under this grant can be forwarded to Jack Davis in the EHAP office of the Medical University of South Carolina at (803) 727-6450.

Damage assessment of bridge infrastructure subjected to flood-related hazards

Science.gov (United States)

Michalis, Panagiotis; Cahill, Paul; Bekić, Damir; Kerin, Igor; Pakrashi, Vikram; Lapthorne, John; Morais, João Gonçalo Martins Paulo; McKeogh, Eamon

2017-04-01

Transportation assets represent a critical component of society's infrastructure systems. Flood-related hazards are considered one of the main climate change impacts on highway and railway infrastructure, threatening the security and functionality of transportation systems. Of such hazards, flood-induced scour is a primarily cause of bridge collapses worldwide and one of the most complex and challenging water flow and erosion phenomena, leading to structural instability and ultimately catastrophic failures. Evaluation of scour risk under severe flood events is a particularly challenging issue considering that depth of foundations is very difficult to evaluate in water environment. The continual inspection, assessment and maintenance of bridges and other hydraulic structures under extreme flood events requires a multidisciplinary approach, including knowledge and expertise of hydraulics, hydrology, structural engineering, geotechnics and infrastructure management. The large number of bridges under a single management unit also highlights the need for efficient management, information sharing and self-informing systems to provide reliable, cost-effective flood and scour risk management. The "Intelligent Bridge Assessment Maintenance and Management System" (BRIDGE SMS) is an EU/FP7 funded project which aims to couple state-of-the art scientific expertise in multidisciplinary engineering sectors with industrial knowledge in infrastructure management. This involves the application of integrated low-cost structural health monitoring systems to provide real-time information towards the development of an intelligent decision support tool and a web-based platform to assess and efficiently manage bridge assets. This study documents the technological experience and presents results obtained from the application of sensing systems focusing on the damage assessment of water-hazards at bridges over watercourses in Ireland. The applied instrumentation is interfaced with an open

Integrated hazard assessment of Cirenmaco glacial lake in Zhangzangbo valley, Central Himalayas

Science.gov (United States)

Wang, Weicai; Gao, Yang; Iribarren Anacona, Pablo; Lei, Yanbin; Xiang, Yang; Zhang, Guoqing; Li, Shenghai; Lu, Anxin

2018-04-01

Glacial lake outburst floods (GLOFs) have recently become one of the primary natural hazards in the Himalayas. There is therefore an urgent need to assess GLOF hazards in the region. Cirenmaco, a moraine-dammed lake located in the upstream portion of Zhangzangbo valley, Central Himalayas, has received public attention after its damaging 1981 outburst flood. Here, by combining remote sensing methods, bathymetric survey and 2D hydraulic modeling, we assessed the hazard posed by Cirenmaco in its current status. Inter-annual variation of Cirenmaco lake area indicates a rapid lake expansion from 0.10 ± 0.08 km2 in 1988 to 0.39 ± 0.04 km2 in 2013. Bathymetric survey shows the maximum water depth of the lake in 2012 was 115 ± 2 m and the lake volume was calculated to be 1.8 × 107 m3. Field geomorphic analysis shows that Cirenmaco glacial lake is prone to GLOFs as mass movements and ice and snow avalanches can impact the lake and the melting of the dead ice in the moraine can lower the dam level. HEC-RAS 2D model was then used to simulate moraine dam failure of the Cirenmaco and assess GLOF impacts downstream. Reconstruction of Cirenmaco 1981 GLOF shows that HEC-RAS can produce reasonable flood extent and water depth, thus demonstrate its ability to effectively model complex GLOFs. GLOF modeling results presented can be used as a basis for the implementation of disaster prevention and mitigation measures. As a case study, this work shows how we can integrate different methods to GLOF hazard assessment.

The Risk Assessment at the Workplace of Assembly Operation

Directory of Open Access Journals (Sweden)

Marek Burda

2014-01-01

Full Text Available Risk Assessment Process by FMEA method involve hazard identification, risk assessment and risk control processes and their input is fundamental to a successful EH&S system. This Risk assessment tool follows the general process and requirements of the Health and Safety Risk Assessment Procedure.

Benefits and hazards of nuclear power

International Nuclear Information System (INIS)

Barnert, H.; Borsch, P.; Feldmann, A.; Merz, E.; Muench, E.; Oesterwind, D.; Voss, A.; Wolters, J.

1979-09-01

Compilation of a seminar at the KFA Juelich on topical problems of nuclear power. Subjects: Energy demand, its expected development and possibilities of coverage; physical fundamentals and technical realisation of power generation by nuclear fission; fuel cycle problems and solutions; effects of radioactive radiation; safety of nuclear power plants and the nuclear hazard as compared with other hazards. (orig./RW) [de

Preliminary environmental impact assessment for the final disposal of vanadium hazardous wastes

International Nuclear Information System (INIS)

Leyva Bombuse, D.; Peralta, J.L.; Gil Castillo, R.

2006-01-01

The aim of the present paper is the environmental impact assessment for the final management of vanadium wastes. The assessed practice is proposed as a final solution for a real problem in Cuba, related with the combustion fossil fuel burn in the electric generation. The study case, embrace the interim storage of hazardous wastes with high vanadium contents (5.08 T) and other heavy metals traces (Cr, Zn). According to the Cuban conditions (tacking into account the environmental regulations and infrastructure lack for the hazardous wastes disposal), it was decided the terrestrial dilution as a final disposal way. The environmental impact assessment methodology used, take into account, in the analyzed management practice, the actions, factors and environmental impacts. The positives and more relevant impacts were obtained for the socioeconomic means. The negative and irrelevant impacts were associated to the biotic and abiotic means. Socioeconomic factors were the most affected and the biotic and abiotic factors were less affected. The waste handling was the most relevant environmental action. According to the evaluated conditions, the obtained results showed that is feasible the terrestrial dilution as a sustainability way for the final disposal of vanadium hazardous wastes

FDA-iRISK--a comparative risk assessment system for evaluating and ranking food-hazard pairs: case studies on microbial hazards.

Science.gov (United States)

Chen, Yuhuan; Dennis, Sherri B; Hartnett, Emma; Paoli, Greg; Pouillot, Régis; Ruthman, Todd; Wilson, Margaret

2013-03-01

Stakeholders in the system of food safety, in particular federal agencies, need evidence-based, transparent, and rigorous approaches to estimate and compare the risk of foodborne illness from microbial and chemical hazards and the public health impact of interventions. FDA-iRISK (referred to here as iRISK), a Web-based quantitative risk assessment system, was developed to meet this need. The modeling tool enables users to assess, compare, and rank the risks posed by multiple food-hazard pairs at all stages of the food supply system, from primary production, through manufacturing and processing, to retail distribution and, ultimately, to the consumer. Using standard data entry templates, built-in mathematical functions, and Monte Carlo simulation techniques, iRISK integrates data and assumptions from seven components: the food, the hazard, the population of consumers, process models describing the introduction and fate of the hazard up to the point of consumption, consumption patterns, dose-response curves, and health effects. Beyond risk ranking, iRISK enables users to estimate and compare the impact of interventions and control measures on public health risk. iRISK provides estimates of the impact of proposed interventions in various ways, including changes in the mean risk of illness and burden of disease metrics, such as losses in disability-adjusted life years. Case studies for Listeria monocytogenes and Salmonella were developed to demonstrate the application of iRISK for the estimation of risks and the impact of interventions for microbial hazards. iRISK was made available to the public at http://irisk.foodrisk.org in October 2012.

Assessing global exposure and vulnerability towards natural hazards: the Disaster Risk Index

Directory of Open Access Journals (Sweden)

P. Peduzzi

2009-07-01

Full Text Available This paper presents a model of factors influencing levels of human losses from natural hazards at the global scale, for the period 1980–2000. This model was designed for the United Nations Development Programme as a building stone of the Disaster Risk Index (DRI, which aims at monitoring the evolution of risk. Assessing what countries are most at risk requires considering various types of hazards, such as droughts, floods, cyclones and earthquakes. Before assessing risk, these four hazards were modelled using GIS and overlaid with a model of population distribution in order to extract human exposure. Human vulnerability was measured by crossing exposure with selected socio-economic parameters. The model evaluates to what extent observed past losses are related to population exposure and vulnerability. Results reveal that human vulnerability is mostly linked with country development level and environmental quality. A classification of countries is provided, as well as recommendations on data improvement for future use of the model.

The application of the geography census data in seismic hazard assessment

Science.gov (United States)

Yuan, Shen; Ying, Zhang

2017-04-01

Limited by basic data timeliness to earthquake emergency database in Sichuan province, after the earthquake disaster assessment results and the actual damage there is a certain gap. In 2015, Sichuan completed the province census for the first time which including topography, traffic, vegetation coverage, water area, desert and bare ground, traffic network, the census residents and facilities, geographical unit, geological hazard as well as the Lushan earthquake-stricken area's town planning construction and ecological environment restoration. On this basis, combining with the existing achievements of basic geographic information data and high resolution image data, supplemented by remote sensing image interpretation and geological survey, Carried out distribution and change situation of statistical analysis and information extraction for earthquake disaster hazard-affected body elements such as surface coverage, roads, structures infrastructure in Lushan county before 2013 after 2015. At the same time, achieved the transformation and updating from geographical conditions census data to earthquake emergency basic data through research their data type, structure and relationship. Finally, based on multi-source disaster information including hazard-affected body changed data and Lushan 7.0 magnitude earthquake CORS network coseismal displacement field, etc. obtaining intensity control points through information fusion. Then completed the seismic influence field correction and assessed earthquake disaster again through Sichuan earthquake relief headquarters technology platform. Compared the new assessment result，original assessment result and actual earthquake disaster loss which shows that the revised evaluation result is more close to the actual earthquake disaster loss. In the future can realize geographical conditions census data to earthquake emergency basic data's normalized updates, ensure the timeliness to earthquake emergency database meanwhile improve the

Seismic Hazard Assessment for a Characteristic Earthquake Scenario: Probabilistic-Deterministic Method

Science.gov (United States)

mouloud, Hamidatou

2016-04-01

The objective of this paper is to analyze the seismic activity and the statistical treatment of seismicity catalog the Constantine region between 1357 and 2014 with 7007 seismic event. Our research is a contribution to improving the seismic risk management by evaluating the seismic hazard in the North-East Algeria. In the present study, Earthquake hazard maps for the Constantine region are calculated. Probabilistic seismic hazard analysis (PSHA) is classically performed through the Cornell approach by using a uniform earthquake distribution over the source area and a given magnitude range. This study aims at extending the PSHA approach to the case of a characteristic earthquake scenario associated with an active fault. The approach integrates PSHA with a high-frequency deterministic technique for the prediction of peak and spectral ground motion parameters in a characteristic earthquake. The method is based on the site-dependent evaluation of the probability of exceedance for the chosen strong-motion parameter. We proposed five sismotectonique zones. Four steps are necessary: (i) identification of potential sources of future earthquakes, (ii) assessment of their geological, geophysical and geometric, (iii) identification of the attenuation pattern of seismic motion, (iv) calculation of the hazard at a site and finally (v) hazard mapping for a region. In this study, the procedure of the earthquake hazard evaluation recently developed by Kijko and Sellevoll (1992) is used to estimate seismic hazard parameters in the northern part of Algeria.

Hazard assessment due to falling stones on a reach of the regional road in the Trenta valley, Slovenia

Directory of Open Access Journals (Sweden)

Urška Petje

2005-12-01

Full Text Available In the framework of the new Slovenian methodology for determining hazard areas and the classification of land parcels into hazard classes due to land slides and rock falls, a pilot project was carried out on the regional road between Bovec and Vr{i~ pass in theTrenta valley. For this around 20 km long road in a typical alpine environment, a hazard assessment of falling rocks was carried out, even tough the road also passes through snow avalanches hazard areas. The performed hazard assessment of falling rocks is based onan expert knowledge taking into account the field mapping, and classifies the road into three hazard classes: 9811 m is classified into the low hazard class, 7233 m is classifiedinto the medium hazard class, and 1301 m is classified into high hazard class of falling rocks.

Emergency preparedness hazards assessment for the Concentrate, Storage and Transfer Facility

International Nuclear Information System (INIS)

Blanchard, A.

2000-01-01

This report documents this facility Emergency Preparedness Hazards Assessment (EPHA) for the Concentrate, Storage and Transfer Facility (CSTF) located on the Department of Energy (DOE) Savannah River Site (SRS). The CSTF encompasses the F-Area and the H-Area Tank Farms including the Replacement High Level Waste Evaporator (RHLWE) (3H evaporator) as a segment of the H-Area Tank Farm. This EPHA is intended to identify and analyze those hazards that are significant enough to warrant consideration in the tank farm operational emergency management programs

Risk assessment of major hazards and its application in urban planning: a case study.

Science.gov (United States)

Zhou, Yafei; Liu, Mao

2012-03-01

With the rapid development of industry in China, the number of establishments that are proposed or under construction is increasing year by year, and many are industries that handle flammable, explosive, toxic, harmful, and dangerous substances. Accidents such as fire, explosion, and toxic diffusion inevitably happen. Accidents resulting from these major hazards in cities cause a large number of casualties and property losses. It is increasingly important to analyze the risk of major hazards in cities realistically and to suitably plan and utilize the surrounding land based on the risk analysis results, thereby reducing the hazards. A theoretical system for risk assessment of major hazards in cities is proposed in this article, and the major hazard risk for the entire city is analyzed quantitatively. Risks of various major accidents are considered together, superposition effect is analyzed, individual risk contours of the entire city are drawn out, and the level of risk in the city is assessed using "as low as reasonably practicable" guidelines. After the entire city's individual risk distribution is obtained, risk zones are divided according to corresponding individual risk value of HSE, and land-use planning suggestions are proposed. Finally, a city in China is used as an example to illustrate the risk assessment process of the city's major hazard and its application in urban land-use planning. The proposed method has a certain theoretical and practical significance in establishing and improving risk analysis of major hazard and urban land-use planning. On the one hand, major urban public risk is avoided; further, the land is utilized in the best possible way in order to obtain the maximum benefit from its use. © 2011 Society for Risk Analysis.

Globe of Natural Hazard - A new assessment tool for risk managers

Science.gov (United States)

Siebert, A. C.

2009-04-01

A large number of tropical cyclones and the earthquake in Sichuan made 2008 one of the most devastating years on record. Throughout the world, more than 220,000 people died as a result of natural catastrophes this year. Overall losses totaled some US 200bn (2007: US 82bn). Insured losses in 2008 rose to US 45bn, about 50% higher than in the previous year. Mainly driven by high losses from weather-related natural catastrophes, 2008 was - on the basis of figures adjusted for inflation - even the third most expensive year on record for the insurance industry, exceeded only by the hurricane year of 2005 and by 1995, the year of the Kobe earthquake. Munich Re, a worldwide operating reinsurance company, is a world leader in terms of investigating risks from natural hazards of all kinds. 2008 has again shown the insurance industry how important it is to analyse risks like natural hazards and climate change in all their facets and to manage the insurance business accordingly. An excellent example of the wealth of knowledge Munich Re has developed in natural hazard assessment is the DVD "Globe of Natural Hazards". It combines the geoscientific data and findings Munich Re has accumulated over a period of 35 years. First devised as a wall-map in 1978, the product has established itself as a standard work for the identification, exposure assessment and risk management of natural hazards. Over 80,000 copies of the CD-ROM version of 2000 have been provided to clients - a mark achieved by no other service product in Munich Re's history. Since the beginning of 2009, the fully updated fourth-generation version has been available. The bilingual DVD (German and English) shows natural hazards and climate effects at a glance: the global maps are presented on a 3D globe, underlaid with satellite images. The hazard complexes of hail, tornado and winter storms have been completely revised and flood incorporated as a new hazard. Users can intuitively home in on and enlarge any location on

Radiological hazard assessment at the Monte Bello Islands

International Nuclear Information System (INIS)

Cooper, M.B.; Martin, L.J.; Wilks, M.J.; Wiliams, G.A.

1990-12-01

Field and laboratory measurements are described and data presented which enabled dose assessments for exposure to artificial radionuclides at the Monte Bello Islands, the sites of U.K. atomic weapons tests in 1952 and 1956. The report focuses on quantifying the inhalation hazard as exposure via the ingestion and wound contamination pathways is considered inconsequential. Surface soil concentrations of radionuclides and particle size analyses are presented for various sampling sites. Analyses of the distribution with depth indicated that, in general, the activity is more or less uniformly mixed through the top 40 mm, although in a few cases the top 10 mm contains the bulk of the activity. The 239 Pu/ 241 Am activity ratios were measured for selected samples. The only potential hazards to health from residual radioactive contamination on the Monte Bello Islands are due to the inhalation of actinides (specifically plutonium and americium) and from the external gamma-radiation field. Only one area, in the fallout plume of HURRICANE to the north-west of Main Beach, is a potential inhalation hazard. For an average inhalable dust loading of 0.1 mg/m 3 , three days occupancy of the most contaminated site will result in a committed effective dose equivalent of 1 mSv. The two ground zeros could not be considered inhalation hazards, considering the small areas concerned and the habits of visitors (full-time occupancy, over a period of one year or more, of the most contaminated sites at either of the G1 or G2 ground zeros would be required to reach 1 mSv). 25 refs., 23 tabs., 3 figs

Landscape susceptibility, hazard and risk assessments along pipeline corridors in Canada

Energy Technology Data Exchange (ETDEWEB)

Blais-Stevens, A.; Couture, R.; Page, A. [Natural Resources Canada, Ottawa, ON (Canada). Geological Survey of Canada; Koch, J.; Clague, J.J. [Simon Fraser Univ., Burnaby, BC (Canada); Lipovsky, P.S. [Yukon Geological Survey, Whitehorse, YT (Canada)

2010-07-01

This article discussed work that was carried out to inventory landslides and assess hazards along two proposed gas-pipeline routes in the North. Landslide inventories and hazard assessments are necessary to quantify and qualify the risk of environmental impacts from landslides on linear infrastructure. The Yukon Alaska Highway Pipeline and the Mackenzie Gas Project Pipeline, which will both be over 800 kilometres in length, will cross harsh landscapes characterized by permafrost terrain and will be at risk from geological hazards, including landslides with debris flows, earthquakes, subsidence, and permafrost degradation. The work involved inventorying and mapping landslides via aerial photography and field visits to identify the frequency-magnitude relationships for debris flow fans along the route and the creation of qualitative parametric landslide maps for both proposed pipeline corridors. A good correlation was found between actual landslide distribution and the landslide susceptibility maps. For the Mackenzie Valley Pipeline Corridor, most landslides have occurred in fine unconsolidated sediments and shallow slopes. Landslides in the Yukon Alaska Highway Corridor mostly happened in unconsolidated sediments, but a few took place in bedrock with high relief. The preliminary investigation revealed that a slope hazard exists in both corridors and must be taken into account during pipeline development. The results are intended to facilitate better decision-making for planning, constructing, and maintaining safe and economically viable pipeline routes in Northern Canada. The mapping methodology was outlined. 13 refs., 1 tab., 6 figs.

Landslide and flood hazard assessment in urban areas of Levoča region (Eastern Slovakia)

Science.gov (United States)

Magulova, Barbora; Caporali, Enrica; Bednarik, Martin

2010-05-01

The case study presents the use of statistical methods and analysis tools, for hazard assessment of "urbanization units", implemented in a Geographic Information Systems (GIS) environment. As a case study, the Levoča region (Slovakia) is selected. The region, with a total area of about 351 km2, is widely affected by landslides and floods. The problem, for small urbanization areas, is nowadays particularly significant from the socio-economic point of view. It is considered, presently, also an increasing problem, mainly because of climate change and more frequent extreme rainfall events. The geo-hazards are evaluated using a multivariate analysis. The landslide hazard assessment is based on the comparison and subsequent statistical elaboration of territorial dependence among different input factors influencing the instability of the slopes. Particularly, five factors influencing slope stability are evaluated, i.e. lithology, slope aspect, slope angle, hypsographic level and present land use. As a result a new landslide susceptibility map is compiled and different zones of stable, dormant and non-stable areas are defined. For flood hazard map a detailed digital elevation model is created. A compose index of flood hazard is derived from topography, land cover and pedology related data. To estimate flood discharge, time series of stream flow and precipitation measurements are used. The assessment results are prognostic maps of landslide hazard and flood hazard, which presents the optimal base for urbanization planning.

Input for seismic hazard assessment using Vrancea seismic source region

International Nuclear Information System (INIS)

Ivan, Iren-Adelina; Enescu, B.D.; Pantea, A.

1998-01-01

We use an extended and combined data base including historical and modern, qualitative and quantitative data, i.e., more than 25 events during the period 1790 - 1990 with epicentral/maximum intensities ranging from X to V degree (MSK scale), the variation interval of isoseismal curves ranging from IX th to III rd degree. The data set was analysed using both the sum phasor techniques of Ridelek and Sacks (1984) for different magnitudes and depth intervals and the Stepp's method. For the assessment of seismic hazard we need a pattern of seismic source regions including an estimation for the maximum expected magnitude and the return period for the studied regions. Another necessary step in seismic hazard assessment is to develop attenuation relationships specific to a seismogenic zone, particularly to sub-crustal earthquakes of Vrancea region. The conceptual frame involves the use of appropriate decay models and consideration of the randomness in the attenuation, taking into account the azimuthal variation of the isoseist shapes. (authors)

Rockfall Hazard Process Assessment : [Project Summary

Science.gov (United States)

2017-10-01

The Montana Department of Transportation (MDT) implemented its Rockfall Hazard Rating System (RHRS) between 2003 and 2005, obtaining information on the state's rock slopes and their associated hazards. The RHRS data facilitated decision-making in an ...

Hazardous waste management in research laboratories

International Nuclear Information System (INIS)

Sundstrom, G.

1989-01-01

Hazardous waste management in research laboratories benefits from a fundamentally different approach to the hazardous waste determination from industry's. This paper introduces new, statue-based criteria for identifying hazardous wastes (such as radiological mixed wastes and waste oils) and links them to a forward-looking compliance of laboratories, the overall system integrates hazardous waste management activities with other environmental and hazard communication initiatives. It is generalizable to other waste generators, including industry. Although only the waste identification and classification aspects of the system are outlined in detail here, four other components are defined or supported, namely: routine and contingency practices; waste treatment/disposal option definition and selection; waste minimization, recycling, reuse, and substitution opportunities; and key interfaces with other systems, including pollution prevention

Quantitative rock-fall hazard and risk assessment for Yosemite Valley, Yosemite National Park, California

Science.gov (United States)

Stock, Greg M.; Luco, Nicolas; Collins, Brian D.; Harp, Edwin L.; Reichenbach, Paola; Frankel, Kurt L.

2014-01-01

Rock falls are common in Yosemite Valley, California, posing substantial hazard and risk to the approximately four million annual visitors to Yosemite National Park. Rock falls in Yosemite Valley over the past few decades have damaged structures and caused injuries within developed regions located on or adjacent to talus slopes highlighting the need for additional investigations into rock-fall hazard and risk. This assessment builds upon previous investigations of rock-fall hazard and risk in Yosemite Valley and focuses on hazard and risk to structures posed by relatively frequent fragmental-type rock falls as large as approximately 100,000 (cubic meters) in volume.

Probabilistic Seismic Hazard Assessment Method for Nonlinear Soil Sites based on the Hazard Spectrum of Bedrock Sites

International Nuclear Information System (INIS)

Hahm, Dae Gi; Seo, Jeong Moon; Choi, In Kil

2011-01-01

For the probabilistic safety assessment of the nuclear power plants (NPP) under seismic events, the rational probabilistic seismic hazard estimation should be performed. Generally, the probabilistic seismic hazard of NPP site is represented by the uniform hazard spectrum (UHS) for the specific annual frequency. In most case, since that the attenuation equations were defined for the bedrock sites, the standard attenuation laws cannot be applied to the general soft soil sites. Hence, for the probabilistic estimation of the seismic hazard of soft soil sites, a methodology of probabilistic seismic hazard analysis (PSHA) coupled with nonlinear dynamic analyses of the soil column are required. Two methods are commonly used for the site response analysis considering the nonlinearity of sites. The one is the deterministic method and another is the probabilistic method. In the analysis of site response, there exist many uncertainty factors such as the variation of the magnitude and frequency contents of input ground motion, and material properties of soil deposits. Hence, nowadays, it is recommended that the adoption of the probabilistic method for the PSHA of soft soil deposits considering such uncertainty factors. In this study, we estimated the amplification factor of the surface of the soft soil deposits with considering the uncertainties of the input ground motions and the soil material properties. Then, we proposed the probabilistic methodology to evaluate the UHS of the soft soil site by multiplying the amplification factor to that of the bedrock site. The proposed method was applied to four typical target sites of KNGR and APR1400 NPP site categories

State Public Health Enabling Authorities: Results of a Fundamental Activities Assessment Examining Core and Essential Services

Science.gov (United States)

Hoss, Aila; Menon, Akshara; Corso, Liza

2016-01-01

Context Public health enabling authorities establish the legal foundation for financing, organizing, and delivering public health services. State laws vary in terms of the content, depth, and breadth of these fundamental public health activities. Given this variance, the Institute of Medicine has identified state public health laws as an area that requires further examination. To respond to this call for further examination, the Centers for Disease Control and Prevention’s Public Health Law Program conducted a fundamental activities legal assessment on state public health laws. Objective The goal of the legal assessment was to examine state laws referencing frameworks representing public health department fundamental activities (ie, core and essential services) in an effort to identify, catalog, and describe enabling authorities of state governmental public health systems. Design In 2013, Public Health Law Program staff compiled a list of state statutes and regulations referencing different commonly-recognized public health frameworks of fundamental activities. The legal assessment included state fundamental activities laws available on WestlawNext as of July 2013. The results related to the 10 essential public health services and the 3 core public health functions were confirmed and updated in June 2016. Results Eighteen states reference commonly-recognized frameworks of fundamental activities in their laws. Thirteen states have listed the 10 essential public health services in their laws. Eight of these states have also referenced the 3 core public health functions in their laws. Five states reference only the core public health functions. Conclusions Several states reference fundamental activities in their state laws, particularly through use of the essential services framework. Further work is needed to capture the public health laws and practices of states that may be performing fundamental activities but without reference to a common framework. PMID

State Public Health Enabling Authorities: Results of a Fundamental Activities Assessment Examining Core and Essential Services.

Science.gov (United States)

Hoss, Aila; Menon, Akshara; Corso, Liza

2016-01-01

Public health enabling authorities establish the legal foundation for financing, organizing, and delivering public health services. State laws vary in terms of the content, depth, and breadth of these fundamental public health activities. Given this variance, the Institute of Medicine has identified state public health laws as an area that requires further examination. To respond to this call for further examination, the Centers for Disease Control and Prevention's Public Health Law Program conducted a fundamental activities legal assessment on state public health laws. The goal of the legal assessment was to examine state laws referencing frameworks representing public health department fundamental activities (ie, core and essential services) in an effort to identify, catalog, and describe enabling authorities of state governmental public health systems. In 2013, Public Health Law Program staff compiled a list of state statutes and regulations referencing different commonly-recognized public health frameworks of fundamental activities. The legal assessment included state fundamental activities laws available on WestlawNext as of July 2013. The results related to the 10 essential public health services and the 3 core public health functions were confirmed and updated in June 2016. Eighteen states reference commonly-recognized frameworks of fundamental activities in their laws. Thirteen states have listed the 10 essential public health services in their laws. Eight of these states have also referenced the 3 core public health functions in their laws. Five states reference only the core public health functions. Several states reference fundamental activities in their state laws, particularly through use of the essential services framework. Further work is needed to capture the public health laws and practices of states that may be performing fundamental activities but without reference to a common framework.

Environmental Hazards Assessment Program: Annual report, July 1, 1995--June 30, 1996

International Nuclear Information System (INIS)

1996-01-01

The objectives of the Environmental Hazards Assessment Program (EHAP) are to: (1) develop a holistic, national basis for risk assessment, risk management, and risk communication that recognizes the direct impact of environmental hazards on the health and well-being of all; (2) develop a pool of talented scientists and experts in cleanup activities, especially in human health aspects; and (3) identify needs and develop programs addressing the critical shortage of well-educated, highly-skilled technical and scientific personnel to address the health-oriented aspects of environmental restoration and waste management. This report describes activities and reports on progress for the fourth year of the grant. It reports progress against these grant objectives and the Program Implementation Plan

Multi-hazard Assessment and Scenario Toolbox (MhAST): A Framework for Analyzing Compounding Effects of Multiple Hazards

Science.gov (United States)

Sadegh, M.; Moftakhari, H.; AghaKouchak, A.

2017-12-01

Many natural hazards are driven by multiple forcing variables, and concurrence/consecutive extreme events significantly increases risk of infrastructure/system failure. It is a common practice to use univariate analysis based upon a perceived ruling driver to estimate design quantiles and/or return periods of extreme events. A multivariate analysis, however, permits modeling simultaneous occurrence of multiple forcing variables. In this presentation, we introduce the Multi-hazard Assessment and Scenario Toolbox (MhAST) that comprehensively analyzes marginal and joint probability distributions of natural hazards. MhAST also offers a wide range of scenarios of return period and design levels and their likelihoods. Contribution of this study is four-fold: 1. comprehensive analysis of marginal and joint probability of multiple drivers through 17 continuous distributions and 26 copulas, 2. multiple scenario analysis of concurrent extremes based upon the most likely joint occurrence, one ruling variable, and weighted random sampling of joint occurrences with similar exceedance probabilities, 3. weighted average scenario analysis based on a expected event, and 4. uncertainty analysis of the most likely joint occurrence scenario using a Bayesian framework.

Environmental and health hazard ranking and assessment of plastic polymers based on chemical composition

Energy Technology Data Exchange (ETDEWEB)

Lithner, Delilah, E-mail: delilah.lithner@gmail.com; Larsson, Ake; Dave, Goeran

2011-08-15

Plastics constitute a large material group with a global annual production that has doubled in 15 years (245 million tonnes in 2008). Plastics are present everywhere in society and the environment, especially the marine environment, where large amounts of plastic waste accumulate. The knowledge of human and environmental hazards and risks from chemicals associated with the diversity of plastic products is very limited. Most chemicals used for producing plastic polymers are derived from non-renewable crude oil, and several are hazardous. These may be released during the production, use and disposal of the plastic product. In this study the environmental and health hazards of chemicals used in 55 thermoplastic and thermosetting polymers were identified and compiled. A hazard ranking model was developed for the hazard classes and categories in the EU classification and labelling (CLP) regulation which is based on the UN Globally Harmonized System. The polymers were ranked based on monomer hazard classifications, and initial assessments were made. The polymers that ranked as most hazardous are made of monomers classified as mutagenic and/or carcinogenic (category 1A or 1B). These belong to the polymer families of polyurethanes, polyacrylonitriles, polyvinyl chloride, epoxy resins, and styrenic copolymers. All have a large global annual production (1-37 million tonnes). A considerable number of polymers (31 out of 55) are made of monomers that belong to the two worst of the ranking model's five hazard levels, i.e. levels IV-V. The polymers that are made of level IV monomers and have a large global annual production (1-5 million tonnes) are phenol formaldehyde resins, unsaturated polyesters, polycarbonate, polymethyl methacrylate, and urea-formaldehyde resins. This study has identified hazardous substances used in polymer production for which the risks should be evaluated for decisions on the need for risk reduction measures, substitution, or even phase out

Decision fundamentals for emergencies in fuel fabrication plants

International Nuclear Information System (INIS)

Thomas, W.; Pfeffer, W.; Wiesemes, J.

1995-01-01

This report is a compilation of fundamental physical and chemical data for emergencies in fuel element fabrication facilities. The release of uranium and plutonium and a criticality accident constitute the main hazards to be considered. In addition information related to the chemical risk of a release of toxic uranium hexafluoride is included in the report. This fundamental information is to be applied in planning emergency measures and could be useful as advisory material for the emergency staff. (orig.) [de

Seismic Hazard and Risk Assessments for Beijing-Tianjin-Tangshan, China, Area

Science.gov (United States)

Xie, Furen; Wang, Zhenming; Liu, Jingwei

2011-03-01

Seismic hazard and risk in the Beijing-Tianjin-Tangshan, China, area were estimated from 500-year intensity observations. First, we digitized the intensity observations (maps) using ArcGIS with a cell size of 0.1 × 0.1°. Second, we performed a statistical analysis on the digitized intensity data, determined an average b value (0.39), and derived the intensity-frequency relationship (hazard curve) for each cell. Finally, based on a Poisson model for earthquake occurrence, we calculated seismic risk in terms of a probability of I ≥ 7, 8, or 9 in 50 years. We also calculated the corresponding 10 percent probability of exceedance of these intensities in 50 years. The advantages of assessing seismic hazard and risk from intensity records are that (1) fewer assumptions (i.e., earthquake source and ground motion attenuation) are made, and (2) site-effect is included. Our study shows that the area has high seismic hazard and risk. Our study also suggests that current design peak ground acceleration or intensity for the area may not be adequate.

Assessment of Nearshore Hazard due to Tsunami-Induced Currents

Science.gov (United States)

Lynett, P. J.; Ayca, A.; Borrero, J. C.; Eskijian, M.; Miller, K.; Wilson, R. I.

2014-12-01

The California Tsunami Program in cooperation with NOAA and FEMA has begun implementing a plan to increase tsunami hazard preparedness and mitigation in maritime communities (both ships and harbor infrastructure) through the development of in-harbor hazard maps, offshore safety zones for boater evacuation, and associated guidance for harbors and marinas before, during and following tsunamis. The hope is that the maritime guidance and associated education program will help save lives and reduce exposure of damage to boats and harbor infrastructure. Findings will be used to develop maps, guidance documents, and consistent policy recommendations for emergency managers and port authorities and provide information critical to real-time decisions required when responding to tsunami alert notifications. The initial goals of the study are to (1) evaluate the effectiveness and sensitivity of existing numerical models for assessing maritime tsunami hazards, (2) find a relationship between current speeds and expected damage levels, (3) evaluate California ports and harbors in terms of tsunami induced hazards by identifying regions that are prone to higher current speeds and damage and to identify regions of relatively lower impact that may be used for evacuation of maritime assets, and (4) determine 'safe depths' for evacuation of vessels from ports and harbors during a tsunami event. We will present details of a new initiative to evaluate the future likelihood of failure for different structural components of a harbor, leading to the identification of high priority areas for mitigation. This presentation will focus on the results from California ports and harbors across the State, and will include feedback we have received from discussions with local harbor masters and port authorities. To help promote accurate and consistent products, the authors are also working through the National Tsunami Hazard Mitigation Program to organize a tsunami current model benchmark workshop.

Deterministic Earthquake Hazard Assessment by Public Agencies in California

Science.gov (United States)

Mualchin, L.

2005-12-01

Even in its short recorded history, California has experienced a number of damaging earthquakes that have resulted in new codes and other legislation for public safety. In particular, the 1971 San Fernando earthquake produced some of the most lasting results such as the Hospital Safety Act, the Strong Motion Instrumentation Program, the Alquist-Priolo Special Studies Zone Act, and the California Department of Transportation (Caltrans') fault-based deterministic seismic hazard (DSH) map. The latter product provides values for earthquake ground motions based on Maximum Credible Earthquakes (MCEs), defined as the largest earthquakes that can reasonably be expected on faults in the current tectonic regime. For surface fault rupture displacement hazards, detailed study of the same faults apply. Originally, hospital, dam, and other critical facilities used seismic design criteria based on deterministic seismic hazard analyses (DSHA). However, probabilistic methods grew and took hold by introducing earthquake design criteria based on time factors and quantifying "uncertainties", by procedures such as logic trees. These probabilistic seismic hazard analyses (PSHA) ignored the DSH approach. Some agencies were influenced to adopt only the PSHA method. However, deficiencies in the PSHA method are becoming recognized, and the use of the method is now becoming a focus of strong debate. Caltrans is in the process of producing the fourth edition of its DSH map. The reason for preferring the DSH method is that Caltrans believes it is more realistic than the probabilistic method for assessing earthquake hazards that may affect critical facilities, and is the best available method for insuring public safety. Its time-invariant values help to produce robust design criteria that are soundly based on physical evidence. And it is the method for which there is the least opportunity for unwelcome surprises.

Rockfall hazard and risk assessment in the Yosemite Valley, California, USA

Science.gov (United States)

Guzzetti, F.; Reichenbach, P.; Wieczorek, G. F.

Rock slides and rock falls are the most frequent types of slope movements in Yosemite National Park, California. In historical time (1857-2002) 392 rock falls and rock slides have been documented in the valley, and some of them have been mapped in detail. We present the results of an attempt to assess rock fall hazards in the Yosemite Valley. Spatial and temporal aspects of rock falls hazard are considered. A detailed inventory of slope movements covering the 145-year period from 1857 to 2002 is used to determine the frequency-volume statistics of rock falls and to estimate the annual frequency of rock falls, providing the temporal component of rock fall hazard. The extent of the areas potentially subject to rock fall hazards in the Yosemite Valley were obtained using STONE, a physically-based rock fall simulation computer program. The software computes 3-dimensional rock fall trajectories starting from a digital elevation model (DEM), the location of rock fall release points, and maps of the dynamic rolling friction coefficient and of the coefficients of normal and tangential energy restitution. For each DEM cell the software calculates the number of rock falls passing through the cell, the maximum rock fall velocity and the maximum flying height. For the Yosemite Valley, a DEM with a ground resolution of 10 × 10 m was prepared using topographic contour lines from the U.S. Geological Survey 1:24 000-scale maps. Rock fall release points were identified as DEM cells having a slope steeper than 60°, an assumption based on the location of historical rock falls. Maps of the normal and tangential energy restitution coefficients and of the rolling friction coefficient were produced from a surficial geologic map. The availability of historical rock falls mapped in detail allowed us to check the computer program performance and to calibrate the model parameters. Visual and statistical comparison of the model results with the mapped rock falls confirmed the accuracy of

Rockfall hazard and risk assessment in the Yosemite Valley, California, USA

Directory of Open Access Journals (Sweden)

F. Guzzetti

2003-01-01

Full Text Available Rock slides and rock falls are the most frequent types of slope movements in Yosemite National Park, California. In historical time (1857–2002 392 rock falls and rock slides have been documented in the valley, and some of them have been mapped in detail. We present the results of an attempt to assess rock fall hazards in the Yosemite Valley. Spatial and temporal aspects of rock falls hazard are considered. A detailed inventory of slope movements covering the 145-year period from 1857 to 2002 is used to determine the frequency-volume statistics of rock falls and to estimate the annual frequency of rock falls, providing the temporal component of rock fall hazard. The extent of the areas potentially subject to rock fall hazards in the Yosemite Valley were obtained using STONE, a physically-based rock fall simulation computer program. The software computes 3-dimensional rock fall trajectories starting from a digital elevation model (DEM, the location of rock fall release points, and maps of the dynamic rolling friction coefficient and of the coefficients of normal and tangential energy restitution. For each DEM cell the software calculates the number of rock falls passing through the cell, the maximum rock fall velocity and the maximum flying height. For the Yosemite Valley, a DEM with a ground resolution of 10 × 10 m was prepared using topographic contour lines from the U.S. Geological Survey 1:24 000-scale maps. Rock fall release points were identified as DEM cells having a slope steeper than 60°, an assumption based on the location of historical rock falls. Maps of the normal and tangential energy restitution coefficients and of the rolling friction coefficient were produced from a surficial geologic map. The availability of historical rock falls mapped in detail allowed us to check the computer program performance and to calibrate the model parameters. Visual and statistical comparison of the model results with the mapped rock falls

Exploring probabilistic tools for the development of a platform for Quantitative Risk Assessment (QRA) of hydro-meteorological hazards in Europe

Science.gov (United States)

Zumpano, V.; Hussin, H. Y.; Breinl, K.

2012-04-01

Mass-movements and floods are hydro-meteorological hazards that can have catastrophic effects on communities living in mountainous areas prone to these disastrous events. Environmental, climate and socio-economic changes are expected to affect the tempo-spatial patterns of hydro-meteorological hazards and associated risks in Europe. These changes and their effects on the occurrence of future hazards need to be analyzed and modeled using probabilistic hazard and risk assessment methods in order to assist stakeholders in disaster management strategies and policy making. Quantitative Risk Assessment (QRA) using probabilistic methods can further calculate damage and losses to multi-hazards and determine the uncertainties related to all the probabilistic components of the hazard and the vulnerability of the elements at risk. Therefore, in order to develop an effective platform that can quantitatively calculate the risk of mass-movements and floods in several European test sites, an extensive inventory and analysis has been carried out of the available tools and software related to the probabilistic risk assessment of single and multi-hazards. The tools have been reviewed based on whether they are open source and freely available, their required input data, the availability and type of hazard and vulnerability modules, transparency of methods used, their validation and calibration techniques, the inclusion of uncertainties and their state of the art. The analysis also specially focused on the applicability of the tools to European study areas. The findings showed that assumptions and simplifications are made when assessing and quantifying the hazards. The interaction between multiple hazards, like cascading effects are not assessed in most tools and some consider the hazard and vulnerability as qualitative components, rather than quantitative ones. This analysis of hazard and risk assessment tools and software will give future developers and experts a better overview of

Hazard Assessment of Debris Flows in the Reservoir Region of Wudongde Hydropower Station in China

Directory of Open Access Journals (Sweden)

Cencen Niu

2015-11-01

Full Text Available The outbreak of debris flows in a reservoir region can affect the stability of hydropower stations and threaten the lives of the people living downstream of dams. Therefore, determining the hazard degree of debris flows in a reservoir region is of great importance. SPOT5 remote sensing images and digital elevation models are introduced to determine the characteristics of debris-flow catchments. The information is acquired through comprehensive manual investigation and satellite image interpretation. Ten factors that influence debris flow are extracted for the hazard assessment. The weight of these factors is determined using the analytic hierarchy process method. As a multi-criterion decision analysis method, fuzzy synthetic evaluation is applied for hazard assessment.

DOE fundamentals handbook: Chemistry

International Nuclear Information System (INIS)

1993-01-01

This handbook was developed to assist nuclear facility operating contractors in providing operators, maintenance personnel, and the technical staff with the necessary fundamentals training to ensure a basic understanding of chemistry. This volume contains the following modules: reactor water chemistry (effects of radiation on water chemistry, chemistry parameters), principles of water treatment (purpose; treatment processes [ion exchange]; dissolved gases, suspended solids, and pH control; water purity), and hazards of chemicals and gases (corrosives [acids, alkalies], toxic compounds, compressed gases, flammable/combustible liquids)

An open framework for automated chemical hazard assessment based on GreenScreen for Safer Chemicals: A proof of concept.

Science.gov (United States)

Wehage, Kristopher; Chenhansa, Panan; Schoenung, Julie M

2017-01-01

GreenScreen® for Safer Chemicals is a framework for comparative chemical hazard assessment. It is the first transparent, open and publicly accessible framework of its kind, allowing manufacturers and governmental agencies to make informed decisions about the chemicals and substances used in consumer products and buildings. In the GreenScreen® benchmarking process, chemical hazards are assessed and classified based on 18 hazard endpoints from up to 30 different sources. The result is a simple numerical benchmark score and accompanying assessment report that allows users to flag chemicals of concern and identify safer alternatives. Although the screening process is straightforward, aggregating and sorting hazard data is tedious, time-consuming, and prone to human error. In light of these challenges, the present work demonstrates the usage of automation to cull chemical hazard data from publicly available internet resources, assign metadata, and perform a GreenScreen® hazard assessment using the GreenScreen® "List Translator." The automated technique, written as a module in the Python programming language, generates GreenScreen® List Translation data for over 3000 chemicals in approximately 30 s. Discussion of the potential benefits and limitations of automated techniques is provided. By embedding the library into a web-based graphical user interface, the extensibility of the library is demonstrated. The accompanying source code is made available to the hazard assessment community. Integr Environ Assess Manag 2017;13:167-176. © 2016 SETAC. © 2016 SETAC.

Microneedle Manufacture: Assessing Hazards and Control Measures

Directory of Open Access Journals (Sweden)

Alexander Martin

2017-10-01

Full Text Available Transdermal microneedles have captured the attention of researchers in relation to a variety of applications, and silicone-based moulds required to produce these systems are now widely available and can be readily manufactured on the lab bench. There is however some concern over the potential for accidental needlestick injuries and, as with any sharp hazard, the potential for blood-borne pathogen transmission must be considered. This follows from recent governmental concerns over the use of microneedle systems in dermabrasion. Despite the piercing nature of the microneedle patch sharing many similarities with conventional hypodermic needles, there are notable factors that mitigate the risk of contamination. A range of microneedle systems has been prepared using micromoulding techniques, and their puncture capability assessed. A critical assessment of the potential for accidental puncture and the control measures needed to ensure safe utilisation of the patch systems is presented.

Probabilistic disaggregation model with application to natural hazard risk assessment of portfolios

DEFF Research Database (Denmark)

Custer, Rocco; Nishijima, Kazuyoshi

In natural hazard risk assessment, a resolution mismatch between hazard data and aggregated exposure data is often observed. A possible solution to this issue is the disaggregation of exposure data to match the spatial resolution of hazard data. Disaggregation models available in literature...... disaggregation model that considers the uncertainty in the disaggregation, taking basis in the scaled Dirichlet distribution. The proposed probabilistic disaggregation model is applied to a portfolio of residential buildings in the Canton Bern, Switzerland, subject to flood risk. Thereby, the model is verified...... are usually deterministic and make use of auxiliary indicator, such as land cover, to spatially distribute exposures. As the dependence between auxiliary indicator and disaggregated number of exposures is generally imperfect, uncertainty arises in disaggregation. This paper therefore proposes a probabilistic...

An Overview of GIS-Based Modeling and Assessment of Mining-Induced Hazards: Soil, Water, and Forest

OpenAIRE

Suh, Jangwon; Kim, Sung-Min; Yi, Huiuk; Choi, Yosoon

2017-01-01

In this study, current geographic information system (GIS)-based methods and their application for the modeling and assessment of mining-induced hazards were reviewed. Various types of mining-induced hazard, including soil contamination, soil erosion, water pollution, and deforestation were considered in the discussion of the strength and role of GIS as a viable problem-solving tool in relation to mining-induced hazards. The various types of mining-induced hazard were classified into two or t...

Initial emission assessment of hazardous-waste-incineration facilities

International Nuclear Information System (INIS)

Harrington, E.S.; Holton, G.A.; O'Donnell, F.R.

1982-01-01

Health and Safety Research Division, sponsored by EPA, conducted a study to quantify emission factors from stacks, spills, fugitives, storage, and treatment for a typical hazardous waste incinerator facility. Engineering participated in preparing flowsheets and providing calculations for fugitive emissions. Typical block-flow diagrams were developed two types of hazardous waste incinerators (rotary kiln and liquid-injector) and for three capacities (small: 1 MM Btu/hr, median: 10 MM Btu/hr, and large: 150 MM Btu/hr). Storage reqirements and support services were determined in more detail. Using the properties of a typical waste, fugitive emissions were determined, including emissions from pump leaks, valve leaks, flange leaks, and tank vents. An atmospheric dispersion model was then employed to calculate atmospheric concentration and population exposure estimates. With these estimates, an assessment was performed to determine the percentage of concentrations and exposure associated with selected emissions from each source at the incineration facility. Results indicated the relative importance of each source at the incineration facility. Results indicated the relative importance of each source both in terms of public health and pollution control requirements

Hazard interactions and interaction networks (cascades) within multi-hazard methodologies

Science.gov (United States)

Gill, Joel C.; Malamud, Bruce D.

2016-08-01

This paper combines research and commentary to reinforce the importance of integrating hazard interactions and interaction networks (cascades) into multi-hazard methodologies. We present a synthesis of the differences between multi-layer single-hazard approaches and multi-hazard approaches that integrate such interactions. This synthesis suggests that ignoring interactions between important environmental and anthropogenic processes could distort management priorities, increase vulnerability to other spatially relevant hazards or underestimate disaster risk. In this paper we proceed to present an enhanced multi-hazard framework through the following steps: (i) description and definition of three groups (natural hazards, anthropogenic processes and technological hazards/disasters) as relevant components of a multi-hazard environment, (ii) outlining of three types of interaction relationship (triggering, increased probability, and catalysis/impedance), and (iii) assessment of the importance of networks of interactions (cascades) through case study examples (based on the literature, field observations and semi-structured interviews). We further propose two visualisation frameworks to represent these networks of interactions: hazard interaction matrices and hazard/process flow diagrams. Our approach reinforces the importance of integrating interactions between different aspects of the Earth system, together with human activity, into enhanced multi-hazard methodologies. Multi-hazard approaches support the holistic assessment of hazard potential and consequently disaster risk. We conclude by describing three ways by which understanding networks of interactions contributes to the theoretical and practical understanding of hazards, disaster risk reduction and Earth system management. Understanding interactions and interaction networks helps us to better (i) model the observed reality of disaster events, (ii) constrain potential changes in physical and social vulnerability

ST-HASSET for volcanic hazard assessment: A Python tool for evaluating the evolution of unrest indicators

Science.gov (United States)

Bartolini, Stefania; Sobradelo, Rosa; Martí, Joan

2016-08-01

Short-term hazard assessment is an important part of the volcanic management cycle, above all at the onset of an episode of volcanic agitation (unrest). For this reason, one of the main tasks of modern volcanology is to use monitoring data to identify and analyse precursory signals and so determine where and when an eruption might occur. This work follows from Sobradelo and Martí [Short-term volcanic hazard assessment through Bayesian inference: retrospective application to the Pinatubo 1991 volcanic crisis. Journal of Volcanology and Geothermal Research 290, 111, 2015] who defined the principle for a new methodology for conducting short-term hazard assessment in unrest volcanoes. Using the same case study, the eruption on Pinatubo (15 June 1991), this work introduces a new free Python tool, ST-HASSET, for implementing Sobradelo and Martí (2015) methodology in the time evolution of unrest indicators in the volcanic short-term hazard assessment. Moreover, this tool is designed for complementing long-term hazard assessment with continuous monitoring data when the volcano goes into unrest. It is based on Bayesian inference and transforms different pre-eruptive monitoring parameters into a common probabilistic scale for comparison among unrest episodes from the same volcano or from similar ones. This allows identifying common pre-eruptive behaviours and patterns. ST-HASSET is especially designed to assist experts and decision makers as a crisis unfolds, and allows detecting sudden changes in the activity of a volcano. Therefore, it makes an important contribution to the analysis and interpretation of relevant data for understanding the evolution of volcanic unrest.

A life cycle hazard assessment (LCHA) framework to address fire hazards at the wildland-urban interface

Science.gov (United States)

Lindquist, Eric; Pierce, Jen; Wuerzer, Thomas; Glenn, Nancy; Dialani, Jijay; Gibble, Katie; Frazier, Tim; Strand, Eva

2015-04-01

up with an assessment of the impact of the product on the environment over time and is being considered beyond the business and logistics communities in such areas as biodiversity and ecosystem impacts. From our perspective, we consider wildfire as the "product" and want to understand how it impacts the environment (spatially, temporally, across the bio-physical and social domains). Through development of this LCHA we adapt the LCA approach with a focus on the inputs (from fire and pre-fire efforts) outputs (from post fire conditions) and how they evolve and are responded to by the responsible agencies and stakeholders responsible. A Life Cycle Hazard Assessment (LCHA) approach extends and integrates the understanding of hazards over much longer periods of time than previously considered. The LCHA also provides an integrated platform for the necessary interdisciplinary approach to understanding decision and environmental change across the life cycle of the fire event. This presentation will discuss our theoretical and empirical framework for developing a longitudinal LCHA and contribute to the overall goals of the NH7.1 session.

Talking about the elephant in the room: Improving fundamental assessment practices

Directory of Open Access Journals (Sweden)

Betty Gill

2015-08-01

Full Text Available This paper reports on an institution-wide strategy to improve first year assessment practices. Assessment is central to the student experience and to informing their developing conceptions of themselves as students. Despite this central importance, much national and international literature raises questions about the fitness-for-purpose of assessment practices in higher education. The reported strategy was developed in response to analysis of student feedback, which suggested, like the literature, substantial opportunity for improvement. Student feedback on their assessment experience was validated by an audit of first session assessment and used to inform the strategy. A significant improvement in quantitative and qualitative measures of student satisfaction across routine data sources is provided to demonstrate impact. This supports a conclusion that the first year student experience can be impacted by the systemic application of a small number of fundamental good practice assessment strategies which are outlined.

Natural radioactivity level and radiological hazard assessment of commonly used building material in Xining, China

International Nuclear Information System (INIS)

Shigang Chao; Xinwei Lu; Mengmeng Zhang; Long Pang

2014-01-01

Natural radioactivity of the commonly used building materials in Xining of China was measured using gamma-ray spectrometer system comprising a NaI(Tl) detector. Radioactivity concentrations of 226 Ra, 232 Th and 40 K in the studied samples range from 11.6 to 120.6, 10.2 to 107.1 and 228.0 to 1,036.2 Bq kg -1 , respectively. The concentrations for these natural radionuclides were compared with the reported data of other countries and the mean value for soil. Radium equivalent activity, indoor air absorbed dose rate, annual effective dose rate as well as external and internal hazard indices were calculated to assess radiological hazards for people living in dwelling made of the building materials. The radiological hazard assessment results show that the studied building materials, except for some aerated concrete block samples, are safe for use in construction of dwellings in the study area and do not pose any significant source of radiation hazard. (author)

From leaves to landscape: A multiscale approach to assess fire hazard in wildland-urban interface areas.

Science.gov (United States)

Ghermandi, Luciana; Beletzky, Natacha A; de Torres Curth, Mónica I; Oddi, Facundo J

2016-12-01

The overlapping zone between urbanization and wildland vegetation, known as the wildland urban interface (WUI), is often at high risk of wildfire. Human activities increase the likelihood of wildfires, which can have disastrous consequences for property and land use, and can pose a serious threat to lives. Fire hazard assessments depend strongly on the spatial scale of analysis. We assessed the fire hazard in a WUI area of a Patagonian city by working at three scales: landscape, community and species. Fire is a complex phenomenon, so we used a large number of variables that correlate a priori with the fire hazard. Consequently, we analyzed environmental variables together with fuel load and leaf flammability variables and integrated all the information in a fire hazard map with four fire hazard categories. The Nothofagus dombeyi forest had the highest fire hazard while grasslands had the lowest. Our work highlights the vulnerability of the wildland-urban interface to fire in this region and our suggested methodology could be applied in other wildland-urban interface areas. Particularly in high hazard areas, our work could help in spatial delimitation policies, urban planning and development of plans for the protection of human lives and assets. Copyright © 2016 Elsevier Ltd. All rights reserved.

Comparative alternative materials assessment to screen toxicity hazards in the life cycle of CIGS thin film photovoltaics

International Nuclear Information System (INIS)

Eisenberg, Daniel A.; Yu, Mengjing; Lam, Carl W.; Ogunseitan, Oladele A.; Schoenung, Julie M.

2013-01-01

Highlights: • Comparative alternatives assessment of thin film manufacturing technologies. • Development of chemical alternatives assessment in a life cycle context. • Screening of manufacturing and solar cell hazardous substances simultaneously. -- Abstract: Copper–indium–gallium–selenium–sulfide (CIGS) thin film photovoltaics are increasingly penetrating the market supply for consumer solar panels. Although CIGS is attractive for producing less greenhouse gas emissions than fossil-fuel based energy sources, CIGS manufacturing processes and solar cell devices use hazardous materials that should be carefully considered in evaluating and comparing net environmental benefits of energy products. Through this research, we present a case study on the toxicity hazards associated with alternative materials selection for CIGS manufacturing. We applied two numeric models, The Green Screen for Safer Chemicals™ and the Toxic Potential Indicator. To improve the sensitivity of the model outputs, we developed a novel, life cycle thinking based hazard assessment method that facilitates the projection of hazards throughout material life cycles. Our results show that the least hazardous CIGS solar cell device and manufacturing protocol consist of a titanium substrate, molybdenum metal back electrode, CuInS 2 p-type absorber deposited by spray pyrolysis, ZnS buffer deposited by spray ion layer gas reduction, ZnO:Ga transparent conducting oxide (TCO) deposited by sputtering, and the encapsulant polydimethylsiloxane

Probabilistic tsunami hazard assessment at Seaside, Oregon, for near-and far-field seismic sources

Science.gov (United States)

Gonzalez, F.I.; Geist, E.L.; Jaffe, B.; Kanoglu, U.; Mofjeld, H.; Synolakis, C.E.; Titov, V.V.; Areas, D.; Bellomo, D.; Carlton, D.; Horning, T.; Johnson, J.; Newman, J.; Parsons, T.; Peters, R.; Peterson, C.; Priest, G.; Venturato, A.; Weber, J.; Wong, F.; Yalciner, A.

2009-01-01

The first probabilistic tsunami flooding maps have been developed. The methodology, called probabilistic tsunami hazard assessment (PTHA), integrates tsunami inundation modeling with methods of probabilistic seismic hazard assessment (PSHA). Application of the methodology to Seaside, Oregon, has yielded estimates of the spatial distribution of 100- and 500-year maximum tsunami amplitudes, i.e., amplitudes with 1% and 0.2% annual probability of exceedance. The 100-year tsunami is generated most frequently by far-field sources in the Alaska-Aleutian Subduction Zone and is characterized by maximum amplitudes that do not exceed 4 m, with an inland extent of less than 500 m. In contrast, the 500-year tsunami is dominated by local sources in the Cascadia Subduction Zone and is characterized by maximum amplitudes in excess of 10 m and an inland extent of more than 1 km. The primary sources of uncertainty in these results include those associated with interevent time estimates, modeling of background sea level, and accounting for temporal changes in bathymetry and topography. Nonetheless, PTHA represents an important contribution to tsunami hazard assessment techniques; viewed in the broader context of risk analysis, PTHA provides a method for quantifying estimates of the likelihood and severity of the tsunami hazard, which can then be combined with vulnerability and exposure to yield estimates of tsunami risk. Copyright 2009 by the American Geophysical Union.

Pre-Participation Screening: The Use of Fundamental Movements as an Assessment of Function – Part 1

OpenAIRE

Cook, Gray; Burton, Lee; Hoogenboom, Barb

2006-01-01

To prepare an athlete for the wide variety of activities needed to participate in their sport, the analysis of fundamental movements should be incorporated into pre-participation screening in order to determine who possesses, or lacks, the ability to perform certain essential movements. In a series of two articles, the background and rationale for the analysis of fundamental movement will be provided. In addition, one such evaluation tool that attempts to assess the fundamental movement patte...

Deterministic approach for multiple-source tsunami hazard assessment for Sines, Portugal

OpenAIRE

Wronna, M.; Omira, R.; Baptista, M. A.

2015-01-01

In this paper, we present a deterministic approach to tsunami hazard assessment for the city and harbour of Sines, Portugal, one of the test sites of project ASTARTE (Assessment, STrategy And Risk Reduction for Tsunamis in Europe). Sines has one of the most important deep-water ports, which has oil-bearing, petrochemical, liquid-bulk, coal, and container terminals. The port and its industrial infrastructures face the ocean southwest towards the main seismogenic sources. This...

Final Report: Seismic Hazard Assessment at the PGDP

Energy Technology Data Exchange (ETDEWEB)

Wang, Zhinmeng [KY Geological Survey, Univ of KY

2007-06-01

Selecting a level of seismic hazard at the Paducah Gaseous Diffusion Plant for policy considerations and engineering design is not an easy task because it not only depends on seismic hazard, but also on seismic risk and other related environmental, social, and economic issues. Seismic hazard is the main focus. There is no question that there are seismic hazards at the Paducah Gaseous Diffusion Plant because of its proximity to several known seismic zones, particularly the New Madrid Seismic Zone. The issues in estimating seismic hazard are (1) the methods being used and (2) difficulty in characterizing the uncertainties of seismic sources, earthquake occurrence frequencies, and ground-motion attenuation relationships. This report summarizes how input data were derived, which methodologies were used, and what the hazard estimates at the Paducah Gaseous Diffusion Plant are.

Undersampling power-law size distributions: effect on the assessment of extreme natural hazards

Science.gov (United States)

Geist, Eric L.; Parsons, Thomas E.

2014-01-01

The effect of undersampling on estimating the size of extreme natural hazards from historical data is examined. Tests using synthetic catalogs indicate that the tail of an empirical size distribution sampled from a pure Pareto probability distribution can range from having one-to-several unusually large events to appearing depleted, relative to the parent distribution. Both of these effects are artifacts caused by limited catalog length. It is more difficult to diagnose the artificially depleted empirical distributions, since one expects that a pure Pareto distribution is physically limited in some way. Using maximum likelihood methods and the method of moments, we estimate the power-law exponent and the corner size parameter of tapered Pareto distributions for several natural hazard examples: tsunamis, floods, and earthquakes. Each of these examples has varying catalog lengths and measurement thresholds, relative to the largest event sizes. In many cases where there are only several orders of magnitude between the measurement threshold and the largest events, joint two-parameter estimation techniques are necessary to account for estimation dependence between the power-law scaling exponent and the corner size parameter. Results indicate that whereas the corner size parameter of a tapered Pareto distribution can be estimated, its upper confidence bound cannot be determined and the estimate itself is often unstable with time. Correspondingly, one cannot statistically reject a pure Pareto null hypothesis using natural hazard catalog data. Although physical limits to the hazard source size and by attenuation mechanisms from source to site constrain the maximum hazard size, historical data alone often cannot reliably determine the corner size parameter. Probabilistic assessments incorporating theoretical constraints on source size and propagation effects are preferred over deterministic assessments of extreme natural hazards based on historic data.

Seismic Hazard Assessment and Uncertainties Treatment: Discussion on the current French regulation, practices and open issues

International Nuclear Information System (INIS)

Berge-Thierry, Catherine

2014-01-01

Taking into account the seismic risk in the context of nuclear safety in France is guided by the Fundamental Safety Rule (RFS2001-01) for the assessment of seismic hazard, and by the Guide ASN/2/01 for the design rules of civil engineering structures. These two references have been updated respectively in 2001 and 2006 and validated by the Nuclear Safety Authority. The French approach is anchored on a deterministic approach. We propose to recall the principles of the methodology recommended by the RFS 2001-01, and to illustrate the advantages and limitations highlighted in recent years. Indeed, this regulatory framework is used both in the design stage and for safety reassessment of all nuclear facilities, power reactors and experimental laboratories and factories. We focus on: (i) key parameters of the approach, and their level of knowledge, (ii) key steps and principles that lead to a non-homogeneous approach between various geographic sites, depending on the seismic activity and / or knowledge, (iii) on physical phenomena (such as the geometric extension of the seismic source, the complexity of earthquake rupture on the fault plane) that are not taken into account, or for which (2D and 3D site effects, and non-linear soil behavior under strong motions), the RFS 2001-01 approach does not provide any guidance, (iv) consideration of epistemic and random uncertainties. We discuss also the probabilistic approaches widely implemented both in France as recently to establish the seismic zoning (reference for the regulation of conventional building and classified installations for the environment), used worldwide and strongly supported by the international Atomic Energy Agency references (safety guides and guidelines). The Tohoku earthquake that occurred in Japan on March 11, 2011, triggering the tsunami that itself caused the nuclear accident at Fukushima Daiichi site has resulted in the realization in France of the Complementary Safety Studies as a request of the

Climatic Changes and Consequences on the French West Indies (C3AF), Hurricane and Tsunami Hazards Assessment

Science.gov (United States)

Arnaud, G.; Krien, Y.; Zahibo, N.; Dudon, B.

2017-12-01

Coastal hazards are among the most worrying threats of our time. In a context of climate change coupled to a large population increase, tropical areas could be the most exposed zones of the globe. In such circumstances, understanding the underlying processes can help to better predict storm surges and the associated global risks.Here we present the partial preliminary results integrated in a multidisciplinary project focused on climatic change effects over the coastal threat in the French West Indies and funded by the European Regional Development Fund. The study aims to provide a coastal hazard assessment based on hurricane surge and tsunami modeling including several aspects of climate changes that can affect hazards such as sea level rise, crustal subsidence/uplift, coastline changes etc. Several tsunamis scenarios have been simulated including tele-tsunamis to ensure a large range of tsunami hazards. Surge level of hurricane have been calculated using a large number of synthetic hurricanes to cover the actual and forecasted climate over the tropical area of Atlantic ocean. This hazard assessment will be later coupled with stakes assessed over the territory to provide risk maps.

KSC VAB Aeroacoustic Hazard Assessment

Science.gov (United States)

Oliveira, Justin M.; Yedo, Sabrina; Campbell, Michael D.; Atkinson, Joseph P.

2010-01-01

NASA Kennedy Space Center (KSC) carried out an analysis of the effects of aeroacoustics produced by stationary solid rocket motors in processing areas at KSC. In the current paper, attention is directed toward the acoustic effects of a motor burning within the Vehicle Assembly Building (VAB). The analysis was carried out with support from ASRC Aerospace who modeled transmission effects into surrounding facilities. Calculations were done using semi-analytical models for both aeroacoustics and transmission. From the results it was concluded that acoustic hazards in proximity to the source of ignition and plume can be severe; acoustic hazards in the far-field are significantly lower.

Seismic risk assessment and application in the central United States

Science.gov (United States)

Wang, Z.

2011-01-01

Seismic risk is a somewhat subjective, but important, concept in earthquake engineering and other related decision-making. Another important concept that is closely related to seismic risk is seismic hazard. Although seismic hazard and seismic risk have often been used interchangeably, they are fundamentally different: seismic hazard describes the natural phenomenon or physical property of an earthquake, whereas seismic risk describes the probability of loss or damage that could be caused by a seismic hazard. The distinction between seismic hazard and seismic risk is of practical significance because measures for seismic hazard mitigation may differ from those for seismic risk reduction. Seismic risk assessment is a complicated process and starts with seismic hazard assessment. Although probabilistic seismic hazard analysis (PSHA) is the most widely used method for seismic hazard assessment, recent studies have found that PSHA is not scientifically valid. Use of PSHA will lead to (1) artifact estimates of seismic risk, (2) misleading use of the annual probability of exccedance (i.e., the probability of exceedance in one year) as a frequency (per year), and (3) numerical creation of extremely high ground motion. An alternative approach, which is similar to those used for flood and wind hazard assessments, has been proposed. ?? 2011 ASCE.

Teachers' Perceptions of a Fundamental Movement Skill (FMS) Assessment Battery in a School Setting

Science.gov (United States)

Lander, Natalie; Morgan, Philip J.; Salmon, Jo; Barnett, Lisa M.

2016-01-01

Fundamental movement skills (FMS) competence is low in adolescent girls. An assessment tool for teachers is needed to monitor FMS in this demographic. The present study explored whether the Canadian Agility and Movement Skill Assessment (CAMSA) is feasible for use by physical education (PE) teachers of Australian Year 7 girls in a school setting.…

Pre-Participation Screening: The Use of Fundamental Movements as an Assessment of Function – Part 1

Science.gov (United States)

Burton, Lee; Hoogenboom, Barb

2006-01-01

To prepare an athlete for the wide variety of activities needed to participate in their sport, the analysis of fundamental movements should be incorporated into pre-participation screening in order to determine who possesses, or lacks, the ability to perform certain essential movements. In a series of two articles, the background and rationale for the analysis of fundamental movement will be provided. In addition, one such evaluation tool that attempts to assess the fundamental movement patterns performed by an individual, the Functional Movement Screen (FMS™), will be described. Three of the seven fundamental movement patterns that comprise the FMS™ are described in detail in Part I: deep squat, hurdle step, and in-line lunge. Part II of this series, which will be published in the August issue of NAJSPT, will provide a brief review of the analysis of fundamental movements, as well a detailed description of the four additional patterns that complement those presented in Part I (to complete the total of seven fundamental movement patterns which comprise the FMS™): shoulder mobility, active straight leg raise, trunk stability push-up, and rotary stability. The intent of this two part series is to introduce the concept of the evaluation of fundamental movements, whether it is the FMS™ system or a different system devised by another clinician. Such a functional assessment should be incorporated into pre-participation screening in order to determine whether the athlete has the essential movements needed to participate in sports activities with a decreased risk of injury. PMID:21522216

A review of multi-risk methodologies for natural hazards: Consequences and challenges for a climate change impact assessment.

Science.gov (United States)

Gallina, Valentina; Torresan, Silvia; Critto, Andrea; Sperotto, Anna; Glade, Thomas; Marcomini, Antonio

2016-03-01

This paper presents a review of existing multi-risk assessment concepts and tools applied by organisations and projects providing the basis for the development of a multi-risk methodology in a climate change perspective. Relevant initiatives were developed for the assessment of multiple natural hazards (e.g. floods, storm surges, droughts) affecting the same area in a defined timeframe (e.g. year, season, decade). Major research efforts were focused on the identification and aggregation of multiple hazard types (e.g. independent, correlated, cascading hazards) by means of quantitative and semi-quantitative approaches. Moreover, several methodologies aim to assess the vulnerability of multiple targets to specific natural hazards by means of vulnerability functions and indicators at the regional and local scale. The overall results of the review show that multi-risk approaches do not consider the effects of climate change and mostly rely on the analysis of static vulnerability (i.e. no time-dependent vulnerabilities, no changes among exposed elements). A relevant challenge is therefore to develop comprehensive formal approaches for the assessment of different climate-induced hazards and risks, including dynamic exposure and vulnerability. This requires the selection and aggregation of suitable hazard and vulnerability metrics to make a synthesis of information about multiple climate impacts, the spatial analysis and ranking of risks, including their visualization and communication to end-users. To face these issues, climate impact assessors should develop cross-sectorial collaborations among different expertise (e.g. modellers, natural scientists, economists) integrating information on climate change scenarios with sectorial climate impact assessment, towards the development of a comprehensive multi-risk assessment process. Copyright © 2015 Elsevier Ltd. All rights reserved.

Ecotoxicological hazard and risk assessment of endocrine active substances.

Science.gov (United States)

Leopold, Annegaaike; Roberts, Mike; Matthiessen, Peter

2017-03-01

This collection of papers provides state-of-the-art science on a complex topic that has been challenging for scientists and regulators for a long time. The papers emanated from the Society of Environmental Toxicology and Chemistry (SETAC) Pellston Workshop ® Environmental Hazard and Risk Assessment Approaches for Endocrine-Active Substances (EHRA). Forty-eight international experts met in early February 2016 to discuss whether the environmental risks posed by endocrine-disrupting substances (EDS) can be reliably assessed. The primary conclusion of the workshop was that if data on environmental exposure, effects on sensitive species and life-stages, delayed effects, and effects at low concentrations are robust, initiating environmental risk assessment of EDS is scientifically sound and reliable. Integr Environ Assess Manag 2017;13:264-266. © 2016 The Authors. Integrated Environmental Assessment and Management published by Wiley Periodicals, Inc. on behalf of Society of Environmental Toxicology & Chemistry (SETAC). © 2016 The Authors. Integrated Environmental Assessment and Management published by Wiley Periodicals, Inc. on behalf of Society of Environmental Toxicology & Chemistry (SETAC).

Comparative alternative materials assessment to screen toxicity hazards in the life cycle of CIGS thin film photovoltaics

Energy Technology Data Exchange (ETDEWEB)

Eisenberg, Daniel A.; Yu, Mengjing; Lam, Carl W. [University of California, Davis, 1 Shields Avenue, Davis, CA 95616 (United States); Ogunseitan, Oladele A. [University of California, Irvine, Irvine, CA 92697 (United States); Schoenung, Julie M., E-mail: jmschoenung@ucdavis.edu [University of California, Davis, 1 Shields Avenue, Davis, CA 95616 (United States)

2013-09-15

Highlights: • Comparative alternatives assessment of thin film manufacturing technologies. • Development of chemical alternatives assessment in a life cycle context. • Screening of manufacturing and solar cell hazardous substances simultaneously. -- Abstract: Copper–indium–gallium–selenium–sulfide (CIGS) thin film photovoltaics are increasingly penetrating the market supply for consumer solar panels. Although CIGS is attractive for producing less greenhouse gas emissions than fossil-fuel based energy sources, CIGS manufacturing processes and solar cell devices use hazardous materials that should be carefully considered in evaluating and comparing net environmental benefits of energy products. Through this research, we present a case study on the toxicity hazards associated with alternative materials selection for CIGS manufacturing. We applied two numeric models, The Green Screen for Safer Chemicals™ and the Toxic Potential Indicator. To improve the sensitivity of the model outputs, we developed a novel, life cycle thinking based hazard assessment method that facilitates the projection of hazards throughout material life cycles. Our results show that the least hazardous CIGS solar cell device and manufacturing protocol consist of a titanium substrate, molybdenum metal back electrode, CuInS{sub 2} p-type absorber deposited by spray pyrolysis, ZnS buffer deposited by spray ion layer gas reduction, ZnO:Ga transparent conducting oxide (TCO) deposited by sputtering, and the encapsulant polydimethylsiloxane.

Neo-Deterministic and Probabilistic Seismic Hazard Assessments: a Comparative Analysis

Science.gov (United States)

Peresan, Antonella; Magrin, Andrea; Nekrasova, Anastasia; Kossobokov, Vladimir; Panza, Giuliano F.

2016-04-01

Objective testing is the key issue towards any reliable seismic hazard assessment (SHA). Different earthquake hazard maps must demonstrate their capability in anticipating ground shaking from future strong earthquakes before an appropriate use for different purposes - such as engineering design, insurance, and emergency management. Quantitative assessment of maps performances is an essential step also in scientific process of their revision and possible improvement. Cross-checking of probabilistic models with available observations and independent physics based models is recognized as major validation procedure. The existing maps from the classical probabilistic seismic hazard analysis (PSHA), as well as those from the neo-deterministic analysis (NDSHA), which have been already developed for several regions worldwide (including Italy, India and North Africa), are considered to exemplify the possibilities of the cross-comparative analysis in spotting out limits and advantages of different methods. Where the data permit, a comparative analysis versus the documented seismic activity observed in reality is carried out, showing how available observations about past earthquakes can contribute to assess performances of the different methods. Neo-deterministic refers to a scenario-based approach, which allows for consideration of a wide range of possible earthquake sources as the starting point for scenarios constructed via full waveforms modeling. The method does not make use of empirical attenuation models (i.e. Ground Motion Prediction Equations, GMPE) and naturally supplies realistic time series of ground shaking (i.e. complete synthetic seismograms), readily applicable to complete engineering analysis and other mitigation actions. The standard NDSHA maps provide reliable envelope estimates of maximum seismic ground motion from a wide set of possible scenario earthquakes, including the largest deterministically or historically defined credible earthquake. In addition

Tsunami Hazard, Vulnerability and Risk assessment for the coast of Oman

Science.gov (United States)

Gonzalez, Mauricio; Aniel-Quiroga, Íñigo; Aguirre-Ayerbe, Ignacio; Álvarez-Gómez, José Antonio; MArtínez, Jara; Gonzalez-Riancho, Pino; Fernandez, Felipe; Medina, Raúl; Al-Yahyai, Sultan

2016-04-01

Tsunamis are relatively infrequent phenomena representing a greater threat than earthquakes, hurricanes and tornadoes, and causing the loss of thousands of human lives and extensive damage to coastal infrastructures around the world. Advances in the understanding and prediction of tsunami impacts allow the development of new methodologies in this field. This work presents the methodology that has been followed for developing the tsunami hazard, vulnerability and risk assessment for the coast of Oman, including maps containing the results of the process. Oman is located in the south eastern corner of the Arabian Peninsula and of the Arabian plate, in front of the Makran Subduction Zone (MSZ), which is the major source of earthquakes in the eastern border of the Arabian plate and Oman (Al-Shaqsi, 2012). There are at least three historical tsunamis assigned to seismic origin in the MSZ (Heidarzadeh et al., 2008; Jordan, 2008). These events show the high potential for tsunami generation of the MSZ, being one of the most tsunamigenic zones in the Indian Ocean. For the tsunami hazard assessment, worst potential cases have been selected, as well as the historical case of 1945, when an 8.1 earthquake generated a tsunami affecting the coast of Oman, and prompting 4000 casualties in the countries of the area. These scenarios have been computationally simulated in order to get tsunami hazard maps, including flooding maps. These calculations have been carried out at national and local scale, in 9 municipalities all along the coast of Oman, including the cities of Sohar, Wudam, Sawadi, Muscat, Quriyat, Sur, Masirah, Al Duqm, and Salalah. Using the hazard assessment as input, this work presents as well an integrated framework for the tsunami vulnerability and risk assessment carried out in the Sultanate of Oman. This framework considers different dimensions (human, structural) and it is developed at two different spatial resolutions, national and local scale. The national

Use of cloud computing technology in natural hazard assessment and emergency management

Science.gov (United States)

Webley, P. W.; Dehn, J.

2015-12-01

During a natural hazard event, the most up-to-date data needs to be in the hands of those on the front line. Decision support system tools can be developed to provide access to pre-made outputs to quickly assess the hazard and potential risk. However, with the ever growing availability of new satellite data as well as ground and airborne data generated in real-time there is a need to analyze the large volumes of data in an easy-to-access and effective environment. With the growth in the use of cloud computing, where the analysis and visualization system can grow with the needs of the user, then these facilities can used to provide this real-time analysis. Think of a central command center uploading the data to the cloud compute system and then those researchers in-the-field connecting to a web-based tool to view the newly acquired data. New data can be added by any user and then viewed instantly by anyone else in the organization through the cloud computing interface. This provides the ideal tool for collaborative data analysis, hazard assessment and decision making. We present the rationale for developing a cloud computing systems and illustrate how this tool can be developed for use in real-time environments. Users would have access to an interactive online image analysis tool without the need for specific remote sensing software on their local system therefore increasing their understanding of the ongoing hazard and mitigate its impact on the surrounding region.

Assessing Surface Fuel Hazard in Coastal Conifer Forests through the Use of LiDAR Remote Sensing

Science.gov (United States)

Koulas, Christos

The research problem that this thesis seeks to examine is a method of predicting conventional fire hazards using data drawn from specific regions, namely the Sooke and Goldstream watershed regions in coastal British Columbia. This thesis investigates whether LiDAR data can be used to describe conventional forest stand fire hazard classes. Three objectives guided this thesis: to discuss the variables associated with fire hazard, specifically the distribution and makeup of fuel; to examine the relationship between derived LiDAR biometrics and forest attributes related to hazard assessment factors defined by the Capitol Regional District (CRD); and to assess the viability of the LiDAR biometric decision tree in the CRD based on current frameworks for use. The research method uses quantitative datasets to assess the optimal generalization of these types of fire hazard data through discriminant analysis. Findings illustrate significant LiDAR-derived data limitations, and reflect the literature in that flawed field application of data modelling techniques has led to a disconnect between the ways in which fire hazard models have been intended to be used by scholars and the ways in which they are used by those tasked with prevention of forest fires. It can be concluded that a significant trade-off exists between computational requirements for wildfire simulation models and the algorithms commonly used by field teams to apply these models with remote sensing data, and that CRD forest management practices would need to change to incorporate a decision tree model in order to decrease risk.

Hydrothermal Liquefaction Treatment Preliminary Hazard Analysis Report

Energy Technology Data Exchange (ETDEWEB)

Lowry, Peter P.; Wagner, Katie A.

2015-08-31

A preliminary hazard assessment was completed during February 2015 to evaluate the conceptual design of the modular hydrothermal liquefaction treatment system. The hazard assessment was performed in 2 stages. An initial assessment utilizing Hazard Identification and Preliminary Hazards Analysis (PHA) techniques identified areas with significant or unique hazards (process safety-related hazards) that fall outside of the normal operating envelope of PNNL and warranted additional analysis. The subsequent assessment was based on a qualitative What-If analysis. This analysis was augmented, as necessary, by additional quantitative analysis for scenarios involving a release of hazardous material or energy with the potential for affecting the public.

Integrating Hazardous Materials Characterization and Assessment Tools to Guide Pollution Prevention in Electronic Products and Manufacturing

Science.gov (United States)

Lam, Carl

Due to technology proliferation, the environmental burden attributed to the production, use, and disposal of hazardous materials in electronics have become a worldwide concern. The major theme of this dissertation is to develop and apply hazardous materials assessment tools to systematically guide pollution prevention opportunities in the context of electronic product design, manufacturing and end-of-life waste management. To this extent, a comprehensive review is first provided on describing hazard traits and current assessment methods to evaluate hazardous materials. As a case study at the manufacturing level, life cycle impact assessment (LCIA)-based and risk-based screening methods are used to quantify chemical and geographic environmental impacts in the U.S. printed wiring board (PWB) industry. Results from this industrial assessment clarify priority waste streams and States to most effectively mitigate impact. With further knowledge of PWB manufacturing processes, select alternative chemical processes (e.g., spent copper etchant recovery) and material options (e.g., lead-free etch resist) are discussed. In addition, an investigation on technology transition effects for computers and televisions in the U.S. market is performed by linking dynamic materials flow and environmental assessment models. The analysis forecasts quantities of waste units generated and maps shifts in environmental impact potentials associated with metal composition changes due to product substitutions. This insight is important to understand the timing and waste quantities expected and the emerging toxic elements needed to be addressed as a consequence of technology transition. At the product level, electronic utility meter devices are evaluated to eliminate hazardous materials within product components. Development and application of a component Toxic Potential Indicator (TPI) assessment methodology highlights priority components requiring material alternatives. Alternative

Probabilistic tsunami hazard assessment considering time-lag of seismic event on Nankai trough

International Nuclear Information System (INIS)

Sugino, Hideharu; Sakagami, Masaharu; Ebisawa, Katsumi; Korenaga, Mariko

2011-01-01

In the area in front of Nankai trough, tsunami wave height may increase if tsunamis attacking from some wave sources overlap because of time-lag of seismic event on Nankai trough. To evaluation tsunami risk of the important facilities located in front of Nankai trough, we proposed the probabilistic tsunami hazard assessment considering uncertainty on time-lag of seismic event on Nankai trough and we evaluated the influence that the time-lag gave to tsunami hazard at the some representative points. (author)

Probabilistic and deterministic risk assessment for extreme objects and ecologically hazardous systems

Directory of Open Access Journals (Sweden)

Yu. V. Veryuzhsky

2003-06-01

Full Text Available The paper include mostly the results of works of the Research Institute for Mechanics of Quickproceeding Processes united in a general research direction - creation of the methodology for risk assessment and risk management for ecologically hazardous systems, consisting of the set of different technological analyzed objects. The elements of system can be characterized by high level of radiation, toxic, explosion, fire and other hazards. The probalistic and deterministic approach for risk assessment, based on mathematical methods of system analysis, non-liner dynamics and computer simulation, has been developed. Branching in problem definition, as well as diversity of factor and criteria for determination of system status, is also taken into account. The risks caused by both objective and subjective factors (including human factor are examined. In many performed studies, the leading structural element, dominating in determination of the system safety, is the structural part of an object. The methodology is implemented for the safety analysis (risk assessment for Chernobyl NPP Shelton Object and other industrial buildings

Assessment of LANL hazardous waste management documentation

International Nuclear Information System (INIS)

Davis, K.D.; Hoevemeyer, S.S.; Stirrup, T.S.; Jennrich, E.A.; Lund, D.M.

1991-04-01

The objective of this report is to present findings from evaluating the Los Alamos National Laboratory (LANL) ''Hazardous Waste Acceptance Criteria Receipt at TA-54, Area L'' to determine if it meets applicable DOE requirements. The guidelines and requirements for the establishment of a Hazardous Waste Acceptance Criteria (HW-WAC) are found in 40 CFR 260 to 270 and DOE Order 5820.2A. Neither set of requirements specifically require a WAC for the management of hazardous waste; however, the use of such documentation is logical and is consistent with the approach required for the management of radioactive waste. The primary purpose of a HW-WAC is to provide generators and waste management with established criteria that must be met before hazardous waste can be acceptable for treatment, storage and/or disposal. An annotated outline for a generic waste acceptance criteria was developed based on the requirements of 40 CFR 260 to 270 and DOE Order 5820.2A. The outline contains only requirements for hazardous waste, it does not address the radiological components of low-level mixed waste. The outline generated from the regulations was used for comparison to the LANL WAC For Chemical and Low-level Mixed Waste Receipt at TA-54, Area L. The major elements that should be addressed by a hazardous waste WAC were determined to be as follows: Waste Package/Container Requirements, Waste Forms, Land Disposal Restrictions, and Data Package-Certification ampersand Documentation

Rockfall Hazard Process Assessment : Final Project Report

Science.gov (United States)

2017-10-01

After a decade of using the Rockfall Hazard Rating System (RHRS), the Montana Department of Transportation (MDT) sought a reassessment of their rockfall hazard evaluation process. Their prior system was a slightly modified version of the RHRS and was...

Multi-hazard national-level risk assessment in Africa using global approaches

Science.gov (United States)

Fraser, Stuart; Jongman, Brenden; Simpson, Alanna; Murnane, Richard

2016-04-01

In recent years Sub-Saharan Africa has been characterized by unprecedented opportunity for transformation and sustained growth. However, natural disasters such as droughts, floods, cyclones, earthquakes, landslides, volcanic eruptions and extreme temperatures cause significant economic and human losses, and major development challenges. Quantitative disaster risk assessments are an important basis for governments to understand disaster risk in their country, and to develop effective risk management and risk financing solutions. However, the data-scarce nature of many Sub-Saharan African countries as well as a lack of financing for risk assessments has long prevented detailed analytics. Recent advances in globally applicable disaster risk modelling practices and data availability offer new opportunities. In December 2013 the European Union approved a € 60 million contribution to support the development of an analytical basis for risk financing and to accelerate the effective implementation of a comprehensive disaster risk reduction. The World Bank's Global Facility for Disaster Reduction and Recovery (GFDRR) was selected as the implementing partner of the Program for Result Area 5: the "Africa Disaster Risk Assessment and Financing Program." As part of this effort, the GFDRR is overseeing the production of national-level multi-hazard risk profiles for a range of countries in Sub-Saharan Africa, using a combination of national and global datasets and state-of-the-art hazard and risk assessment methodologies. In this presentation, we will highlight the analytical approach behind these assessments, and show results for the first five countries for which the assessment has been completed (Kenya, Uganda, Senegal, Niger and Ethiopia). The presentation will also demonstrate the visualization of the risk assessments into understandable and visually attractive risk profile documents.

BEHAVIORAL HAZARD IN HEALTH INSURANCE*

Science.gov (United States)

Baicker, Katherine; Mullainathan, Sendhil; Schwartzstein, Joshua

2015-01-01

A fundamental implication of standard moral hazard models is overuse of low-value medical care because copays are lower than costs. In these models, the demand curve alone can be used to make welfare statements, a fact relied on by much empirical work. There is ample evidence, though, that people misuse care for a different reason: mistakes, or “behavioral hazard.” Much high-value care is underused even when patient costs are low, and some useless care is bought even when patients face the full cost. In the presence of behavioral hazard, welfare calculations using only the demand curve can be off by orders of magnitude or even be the wrong sign. We derive optimal copay formulas that incorporate both moral and behavioral hazard, providing a theoretical foundation for value-based insurance design and a way to interpret behavioral “nudges.” Once behavioral hazard is taken into account, health insurance can do more than just provide financial protection—it can also improve health care efficiency. PMID:23930294

National Environmental Policy Act Hazards Assessment for the TREAT Alternative

Energy Technology Data Exchange (ETDEWEB)

Christensen, Boyd D. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Schafer, Annette L. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2014-02-01

This document provides an assessment of hazards as required by the National Environmental Policy Act for the alternative of restarting the reactor at the Transient Reactor Test (TREAT) facility by the Resumption of Transient Testing Program. Potential hazards have been identified and screening level calculations have been conducted to provide estimates of unmitigated dose consequences that could be incurred through this alternative. Consequences considered include those related to use of the TREAT Reactor, experiment assembly handling, and combined events involving both the reactor and experiments. In addition, potential safety structures, systems, and components for processes associated with operating TREAT and onsite handling of nuclear fuels and experiments are listed. If this alternative is selected, a safety basis will be prepared in accordance with 10 CFR 830, “Nuclear Safety Management,” Subpart B, “Safety Basis Requirements.”

National Environmental Policy Act Hazards Assessment for the TREAT Alternative

Energy Technology Data Exchange (ETDEWEB)

Boyd D. Christensen; Annette L. Schafer

2013-11-01

This document provides an assessment of hazards as required by the National Environmental Policy Act for the alternative of restarting the reactor at the Transient Reactor Test (TREAT) facility by the Resumption of Transient Testing Program. Potential hazards have been identified and screening level calculations have been conducted to provide estimates of unmitigated dose consequences that could be incurred through this alternative. Consequences considered include those related to use of the TREAT Reactor, experiment assembly handling, and combined events involving both the reactor and experiments. In addition, potential safety structures, systems, and components for processes associated with operating TREAT and onsite handling of nuclear fuels and experiments are listed. If this alternative is selected, a safety basis will be prepared in accordance with 10 CFR 830, “Nuclear Safety Management,” Subpart B, “Safety Basis Requirements.”

Seismic Hazard Assessment in Site Evaluation for Nuclear Installations: Ground Motion Prediction Equations and Site Response

International Nuclear Information System (INIS)

2016-07-01

The objective of this publication is to provide the state-of-the-art practice and detailed technical elements related to ground motion evaluation by ground motion prediction equations (GMPEs) and site response in the context of seismic hazard assessments as recommended in IAEA Safety Standards Series No. SSG-9, Seismic Hazards in Site Evaluation for Nuclear Installations. The publication includes the basics of GMPEs, ground motion simulation, selection and adjustment of GMPEs, site characterization, and modelling of site response in order to improve seismic hazard assessment. The text aims at delineating the most important aspects of these topics (including current practices, criticalities and open problems) within a coherent framework. In particular, attention has been devoted to filling conceptual gaps. It is written as a reference text for trained users who are responsible for planning preparatory seismic hazard analyses for siting of all nuclear installations and/or providing constraints for anti-seismic design and retrofitting of existing structures

Environmental Hazards Assessment Program annual report, July 1, 1993--June 30, 1994

Energy Technology Data Exchange (ETDEWEB)

1994-08-17

On June 23, 1992, the US Department of Energy (DOE) signed Assistance Instrument Number DE-FG01-92EW50625 with the Medical University of South Carolina (MUSC) to support the Environmental Hazards Assessment Program (EHAP). The objectives of the EHAP program stated in the proposal to DOE are to: (1) Develop a holistic, national basis for risk assessment, risk management, and risk communication which recognizes the direct impact of environmental hazards on the health and well-being of all. (2) Develop a pool of talented scientists and experts in cleanup activities, especially in human health aspects; and (3) Identify needs and develop programs addressing the critical shortage of well-educated, highly-skilled technical and scientific personnel to address the health oriented aspects of environmental restoration and waste management. This report describes activities and reports on progress for the second year of the grant.

Environmental Hazards Assessment Program annual report, July 1, 1993--June 30, 1994

International Nuclear Information System (INIS)

1994-01-01

On June 23, 1992, the US Department of Energy (DOE) signed Assistance Instrument Number DE-FG01-92EW50625 with the Medical University of South Carolina (MUSC) to support the Environmental Hazards Assessment Program (EHAP). The objectives of the EHAP program stated in the proposal to DOE are to: (1) Develop a holistic, national basis for risk assessment, risk management, and risk communication which recognizes the direct impact of environmental hazards on the health and well-being of all. (2) Develop a pool of talented scientists and experts in cleanup activities, especially in human health aspects; and (3) Identify needs and develop programs addressing the critical shortage of well-educated, highly-skilled technical and scientific personnel to address the health oriented aspects of environmental restoration and waste management. This report describes activities and reports on progress for the second year of the grant

Hazard identification and risk assessment for biologics targeting the immune system.

Science.gov (United States)

Weir, Andrea B

2008-01-01

Biologic pharmaceuticals include a variety of products, such as monoclonal antibodies, fusion proteins and cytokines. Products in those classes include immunomodulatory biologics, which are intended to enhance or diminish the activity of the immune system. Immunomodulatory biologics have been approved by the U.S. FDA for a variety of indications, including cancer and inflammatory conditions. Prior to gaining approval for marketing, sponsoring companies for all types of products must demonstrate a product's safety in toxicology studies conducted in animals and show safety and efficacy in clinical trials conducted in patients. The overall goal of toxicology studies, which applies to immunomodulatory and other product types, is to identify the hazards that products pose to humans. Because biologics are generally highly selective for specific targets (receptors/epitopes), conducting toxicology studies in animal models with the target is essential. Such animals are referred to as pharmacologically relevant. Endpoints routinely included in toxicology studies, such as hematology, organ weight and histopathology, can be used to assess the effect of a product on the structure of the immune system. Additionally, specialized endpoints, such as immunophenotyping and immune function tests, can be used to define effects of immunomodulatory products on the immune system. Following hazard identification, risks posed to patients are assessed and managed. Risks can be managed through clinical trial design and risk communication, a practice that applies to immunomodulatory and other product types. Examples of risk management in clinical trial design include establishing a safe starting dose, defining the appropriate patient population and establishing appropriate patient monitoring. Risk communication starts during clinical trials and continues after product approval. A combination of hazard identification, risk assessment and risk management allows for drug development to proceed

Risk assessment of hazardous impacts on urbanization and industrialization activities based upon toxic substances

Directory of Open Access Journals (Sweden)

T. Salem

2016-03-01

Full Text Available A risk assessment study was conducted to predict the expected hazardous influence on the ecosystem resulted from urbanization and industrialization activities at Helwan area, Egypt. To achieve these goals, soils, plants and water samples were collected from Helwan area, and their total concentrations of inorganic contaminants (Cd, Cr, Co, Cu, Fe, Mn, Ni, Pb, and Zn and organic pollutants; such as Phenol and hydrocarbons were measured. The obtained results showed that, the concentrations of organic contaminants in water streams and surrounding soils recorded high concentration values than the permissible limits, while inorganic elements were within the safe limits for irrigation. In addition, soils irrigated with the effluents of industrial units recorded high values of inorganic and organic contaminants. Consequently, the levels of these contaminants were high in plant tissues grown thereon; especially the edible parts. Risk assessment based on available Predicted No Effect Concentration values for the aquatic and terrestrial environment was performed. Inorganic elements were expected to cause serious hazard problems for both aquatic organisms and soil microorganisms. The impact of these pollutants on human health was calculated using daily metals intake of inorganic metals via consumption of edible plants. Hazard index values proved that concentrations of Cr may cause serious hazard problems for humans in this area; especially, children.

Application of Gumbel I and Monte Carlo methods to assess seismic hazard in and around Pakistan

Science.gov (United States)

Rehman, Khaista; Burton, Paul W.; Weatherill, Graeme A.

2018-05-01

A proper assessment of seismic hazard is of considerable importance in order to achieve suitable building construction criteria. This paper presents probabilistic seismic hazard assessment in and around Pakistan (23° N-39° N; 59° E-80° E) in terms of peak ground acceleration (PGA). Ground motion is calculated in terms of PGA for a return period of 475 years using a seismogenic-free zone method of Gumbel's first asymptotic distribution of extreme values and Monte Carlo simulation. Appropriate attenuation relations of universal and local types have been used in this study. The results show that for many parts of Pakistan, the expected seismic hazard is relatively comparable with the level specified in the existing PGA maps.

Establishing indices for groundwater contamination risk assessment in the vicinity of hazardous waste landfills in China

International Nuclear Information System (INIS)

Li Ying; Li Jinhui; Chen Shusheng; Diao Weihua

2012-01-01

Groundwater contamination by leachate is the most damaging environmental impact over the entire life of a hazardous waste landfill (HWL). With the number of HWL facilities in China rapidly increasing, and considering the poor status of environmental risk management, it is imperative that effective environmental risk management methods be implemented. A risk assessment indices system for HWL groundwater contamination is here proposed, which can simplify the risk assessment procedure and make it more user-friendly. The assessment framework and indices were drawn from five aspects: source term, underground media, leachate properties, risk receptors and landfill management quality, and a risk assessment indices system consisting of 38 cardinal indicators was established. Comparison with multimedia models revealed that the proposed indices system was integrated and quantitative, that input data for it could be easily collected, and that it could be widely used for environmental risk assessment (ERA) in China. - Highlights: ► No comprehensive environmental risk assessment method for hazardous waste management is proposed in China. ► An assessment indices system is established for groundwater contamination in the vicinity of hazardous waste landfill. ► All indicators are quantitative and applicable in China. - Capsule: This research identified critical indices and established a system for environmental risk assessment for groundwater contamination in the vicinity of HWLs in China.

Review Article: Lake and breach hazard assessment for moraine-dammed lakes: an example from the Cordillera Blanca (Peru

Directory of Open Access Journals (Sweden)

A. Emmer

2013-06-01

Full Text Available Glacial lake outburst floods (GLOFs and related debris flows represent a significant threat in high mountainous areas across the globe. It is necessary to quantify this threat so as to mitigate their catastrophic effects. Complete GLOF hazard assessment incorporates two phases: the probability of water release from a given glacial lake is estimated through lake and breach hazard assessment while the endangered areas are identified during downstream hazard assessment. This paper outlines a number of methods of lake and breach hazard assessment, which can be grouped into three categories: qualitative, of which we outline eight; semi-quantitative, of which we outline two; and quantitative, of which we outline three. It is considered that five groups of critical parameters are essential for an accurate regionally focused hazard assessment method for moraine-dammed lakes in the Cordillera Blanca. These comprise the possibility of dynamic slope movements into the lake, the possibility of a flood wave from a lake situated upstream, the possibility of dam rupture following a large earthquake, the size of the dam freeboard (or ratio of dam freeboard, and a distinction between natural dams and those with remedial work. It is shown that none of the summarised methods uses all these criteria with, at most, three of the five considered by the outlined methods. A number of these methods were used on six selected moraine-dammed lakes in the Cordillera Blanca: lakes Quitacocha, Checquiacocha, Palcacocha, Llaca, Rajucolta, and Tararhua. The results have been compared and show that each method has certain advantages and disadvantages when used in this region. These methods demonstrate that the most hazardous lake is Lake Palcacocha.

Methodology for environmental assessments of oil and hazardous substance spills

Science.gov (United States)

Davis, W. P.; Scott, G. I.; Getter, C. D.; Hayes, M. O.; Gundlach, E. R.

1980-03-01

Scientific assessment of the complex environmental consequences of large spills of oil or other hazardous substances has stimulated development of improved strategies for rapid and valid collection and processing of ecological data. The combination of coastal processes and geological measurements developed by Hayes & Gundlach (1978), together with selected field biological and chemical observations/measurements, provide an ecosystem impact assessment approach which is termed “integrated zonal method of ecological impact assessment.” Ecological assessment of oil and hazardous material spills has been divided into three distinct phases: (1) first-order response studies — conducted at the time of the initial spill event, which gather data to document acute impacts and assist decision-makers in prioritization of cleanup efforts and protection of ecologically sensitive habitats, (2) second-order response studies — conducted two months to one year post-spill, which document any delayed mortality and attempt to identify potential sublethal impacts in sensitive species, and (3) third-order response studies — conducted one to three years post-spill, to document chronic impacts (both lethal and sublethal) to specific indicator species. Data collected during first-order response studies are gathered in a quantitative manner so that the initial assessment may become a baseline for later, more detailed, post-spill scientific efforts. First- and second-order response studies of the “Peck Slip” oil spill in Puerto Rico illustrate the usefulness of this method. The need for contingency planning before a spill has been discussed along with the use of the Vulnerability Index, a method in which coastal environments are classified on a scale of 1 10, based upon their potential susceptibility to oiling. A study of the lower Cook Inlet section of the Alaskan coast illustrates the practical application of this method.

A transparent and data-driven global tectonic regionalization model for seismic hazard assessment

Science.gov (United States)

Chen, Yen-Shin; Weatherill, Graeme; Pagani, Marco; Cotton, Fabrice

2018-05-01

A key concept that is common to many assumptions inherent within seismic hazard assessment is that of tectonic similarity. This recognizes that certain regions of the globe may display similar geophysical characteristics, such as in the attenuation of seismic waves, the magnitude scaling properties of seismogenic sources or the seismic coupling of the lithosphere. Previous attempts at tectonic regionalization, particularly within a seismic hazard assessment context, have often been based on expert judgements; in most of these cases, the process for delineating tectonic regions is neither reproducible nor consistent from location to location. In this work, the regionalization process is implemented in a scheme that is reproducible, comprehensible from a geophysical rationale, and revisable when new relevant data are published. A spatial classification-scheme is developed based on fuzzy logic, enabling the quantification of concepts that are approximate rather than precise. Using the proposed methodology, we obtain a transparent and data-driven global tectonic regionalization model for seismic hazard applications as well as the subjective probabilities (e.g. degree of being active/degree of being cratonic) that indicate the degree to which a site belongs in a tectonic category.

Assessment for the management of NORM wastes in conventional hazardous and nonhazardous waste landfills

Energy Technology Data Exchange (ETDEWEB)

Mora, Juan C., E-mail: jc.mora@ciemat.es [Unit for Radiation Protection of the Public and the Environment (PRPYMA), CIEMAT, Avda. Complutense, 40, 28040 Madrid (Spain); Energy Engineering Department, Power Engineering, Nuclear Area, ETSII, UNED (Spain); Baeza, Antonio [LARUEX, Dpt. Applied Physics, Faculty of Veterinary Science, University of Extremadura, Avda. Universidad, s/n, 10071 Cáceres (Spain); Robles, Beatriz [Unit for Radiation Protection of the Public and the Environment (PRPYMA), CIEMAT, Avda. Complutense, 40, 28040 Madrid (Spain); Sanz, Javier [Energy Engineering Department, Power Engineering, Nuclear Area, ETSII, UNED (Spain)

2016-06-05

Highlights: • Before 2010 NORM waste is managed as non-radioactive, disposed in landfills. • After 2010 radiological impact of the management of NORM wastes must be assessed. • Quantities that can be disposed in hazardous or non-hazardous landfills are given. • Uncertainty analysis is included to provide consistency to the calculations. - Abstract: Naturally Occurring Radioactive Materials (NORM) wastes are generated in huge quantities in several industries and their management has been carried out under considerations of industrial non-radioactive wastes, before the concern on the radioactivity content was included in the legislation. Therefore these wastes were conditioned using conventional methods and the waste disposals were designed to isolate toxic elements from the environment for long periods of time. Spanish regulation for these conventional toxic waste disposals includes conditions that assure adequate isolation to minimize the impact of the wastes to the environment in present and future conditions. After 1996 the radiological impact of the management of NORM wastes is considered and all the aspects related with natural radiations and the radiological control regarding the management of residues from NORM industries were developed in the new regulation. One option to be assessed is the disposal of NORM wastes in hazardous and non-hazardous waste disposals, as was done before this new regulation. This work analyses the management of NORM wastes in these landfills to derive the masses that can be disposed without considerable radiological impact. Generic dose assessments were carried out under highly conservative hypothesis and a discussion on the uncertainty and variability sources was included to provide consistency to the calculations.

Assessment for the management of NORM wastes in conventional hazardous and nonhazardous waste landfills

International Nuclear Information System (INIS)

Mora, Juan C.; Baeza, Antonio; Robles, Beatriz; Sanz, Javier

2016-01-01

Highlights: • Before 2010 NORM waste is managed as non-radioactive, disposed in landfills. • After 2010 radiological impact of the management of NORM wastes must be assessed. • Quantities that can be disposed in hazardous or non-hazardous landfills are given. • Uncertainty analysis is included to provide consistency to the calculations. - Abstract: Naturally Occurring Radioactive Materials (NORM) wastes are generated in huge quantities in several industries and their management has been carried out under considerations of industrial non-radioactive wastes, before the concern on the radioactivity content was included in the legislation. Therefore these wastes were conditioned using conventional methods and the waste disposals were designed to isolate toxic elements from the environment for long periods of time. Spanish regulation for these conventional toxic waste disposals includes conditions that assure adequate isolation to minimize the impact of the wastes to the environment in present and future conditions. After 1996 the radiological impact of the management of NORM wastes is considered and all the aspects related with natural radiations and the radiological control regarding the management of residues from NORM industries were developed in the new regulation. One option to be assessed is the disposal of NORM wastes in hazardous and non-hazardous waste disposals, as was done before this new regulation. This work analyses the management of NORM wastes in these landfills to derive the masses that can be disposed without considerable radiological impact. Generic dose assessments were carried out under highly conservative hypothesis and a discussion on the uncertainty and variability sources was included to provide consistency to the calculations.

Toward risk assessment 2.0: Safety supervisory control and model-based hazard monitoring for risk-informed safety interventions

International Nuclear Information System (INIS)

Favarò, Francesca M.; Saleh, Joseph H.

2016-01-01

Probabilistic Risk Assessment (PRA) is a staple in the engineering risk community, and it has become to some extent synonymous with the entire quantitative risk assessment undertaking. Limitations of PRA continue to occupy researchers, and workarounds are often proposed. After a brief review of this literature, we propose to address some of PRA's limitations by developing a novel framework and analytical tools for model-based system safety, or safety supervisory control, to guide safety interventions and support a dynamic approach to risk assessment and accident prevention. Our work shifts the emphasis from the pervading probabilistic mindset in risk assessment toward the notions of danger indices and hazard temporal contingency. The framework and tools here developed are grounded in Control Theory and make use of the state-space formalism in modeling dynamical systems. We show that the use of state variables enables the definition of metrics for accident escalation, termed hazard levels or danger indices, which measure the “proximity” of the system state to adverse events, and we illustrate the development of such indices. Monitoring of the hazard levels provides diagnostic information to support both on-line and off-line safety interventions. For example, we show how the application of the proposed tools to a rejected takeoff scenario provides new insight to support pilots’ go/no-go decisions. Furthermore, we augment the traditional state-space equations with a hazard equation and use the latter to estimate the times at which critical thresholds for the hazard level are (b)reached. This estimation process provides important prognostic information and produces a proxy for a time-to-accident metric or advance notice for an impending adverse event. The ability to estimate these two hazard coordinates, danger index and time-to-accident, offers many possibilities for informing system control strategies and improving accident prevention and risk mitigation

Assessment of human health hazard due to metal uptake via fish ...

African Journals Online (AJOL)

Assessment of human health hazard due to metal uptake via fish consumption from coastal area of Tanzania. ... The result shows that the concentration and THQ of As in all fish samples ranges from 1.173 – 2.325 which is > 1, hence signified that a daily exposure at this level are in risk of cancer during a person lifetime.

Autonomous Soil Assessment System: A Data-Driven Approach to Planetary Mobility Hazard Detection

Science.gov (United States)

Raimalwala, K.; Faragalli, M.; Reid, E.

2018-04-01

The Autonomous Soil Assessment System predicts mobility hazards for rovers. Its development and performance are presented, with focus on its data-driven models, machine learning algorithms, and real-time sensor data fusion for predictive analytics.

Sanitary Assessment of Hazardous Materials Exposed To Highly Toxic Chemical Compounds

International Nuclear Information System (INIS)

Rembovskiy, V.; Ermolaeva, E.

2007-01-01

Industrial or terroristic accidents in which toxic chemicals (TC) are the main or attendant damaging factors should be regarded as a new challenge for experts, because of little knowledge on the methodology to estimating the long-term risk for humans due to contamination of the building materials and environment. In the Russian Federation, there appeared to be a kind of model systems for developing an algorithm for solving these or similar problems. Under dismantling and liquidation of the former facilities for chemical weapon production (FCWP) the building materials are regarded as potential waste products the fate of which (processing, warehousing, utilization, and destruction) is dependent on their possible hazard for human population and environment. The standard approaches for hazard assessment of waste products of the FCWP turned out to be insufficient. When conducting the present work, the following problems have been solved: 1. Selection of representative samples taking into consideration a diversity of construction materials, great quantities of potentially toxic waste materials, information on the production conditions, breakdowns in the process of production, accidents, composition of the decontaminators used, decontamination frequency, etc. 2. Analysis of TC in composite matrixes complicated by the following problems: extraction, masking effects of concomitant components during indirect analysis, lack of certified methods of direct analysis of TC, discrepancy of results of GC and direct GCMS analysis, low sensitivity of GCMS analysis, big volume of samples (more than 0.5 kg), heterogeneity of physical-chemical properties of different matrixes influencing the process of degradation of TC. 3. Hazard assessment of the wastes in toxic-and-sanitary experiment relying on non-specific signs of intoxication due to relatively low percentage of TC and masking effects of various matrix components. Application of the integral toxicity tests with soil

Physical Education Teacher Training in Fundamental Movement Skills Makes a Difference to Instruction and Assessment Practices

Science.gov (United States)

Lander, Natalie Jayne; Barnett, Lisa M.; Brown, Helen; Telford, Amanda

2015-01-01

The purpose of this study was to investigate instruction and assessment of fundamental movement skills (FMSs) by Physical Education (PE) teachers of Year 7 girls. Of 168 secondary school PE teachers, many had received little FMSs professional development, and although most assessed student FMSs proficiency, the quality of assessment was variable.…

Seismic hazard assessment based on the Unified Scaling Law for Earthquakes: the Greater Caucasus

Science.gov (United States)

Nekrasova, A.; Kossobokov, V. G.

2015-12-01

Losses from natural disasters continue to increase mainly due to poor understanding by majority of scientific community, decision makers and public, the three components of Risk, i.e., Hazard, Exposure, and Vulnerability. Contemporary Science is responsible for not coping with challenging changes of Exposures and their Vulnerability inflicted by growing population, its concentration, etc., which result in a steady increase of Losses from Natural Hazards. Scientists owe to Society for lack of knowledge, education, and communication. In fact, Contemporary Science can do a better job in disclosing Natural Hazards, assessing Risks, and delivering such knowledge in advance catastrophic events. We continue applying the general concept of seismic risk analysis in a number of seismic regions worldwide by constructing regional seismic hazard maps based on the Unified Scaling Law for Earthquakes (USLE), i.e. log N(M,L) = A - B•(M-6) + C•log L, where N(M,L) is the expected annual number of earthquakes of a certain magnitude M within an seismically prone area of linear dimension L. The parameters A, B, and C of USLE are used to estimate, first, the expected maximum magnitude in a time interval at a seismically prone cell of a uniform grid that cover the region of interest, and then the corresponding expected ground shaking parameters including macro-seismic intensity. After a rigorous testing against the available seismic evidences in the past (e.g., the historically reported macro-seismic intensity), such a seismic hazard map is used to generate maps of specific earthquake risks (e.g., those based on the density of exposed population). The methodology of seismic hazard and risks assessment based on USLE is illustrated by application to the seismic region of Greater Caucasus.

Seismic hazard assessment for Central, North and Northwest Europe: GSHAP Region 3

Czech Academy of Sciences Publication Activity Database

Grunthal, G.; Bosse, Ch.; Camelbeeck, T.; de Crook, T.; Gariel, J. C.; Gregersen, S.; Guterch, B.; Halldorsson, P.; Labák, P.; Lindholm, C.; Lenhardt, W.; Mantyniemi, P.; Mayer-Rosa, D.; Musson, R. M. W.; Schenk, Vladimír; Schenková, Zdeňka; Slejko, D.; Verbeiren, R.; Wahlstrom, R.; Zabukovec, B.; Ziros, T.

1999-01-01

Roč. 42, č. 6 (1999), s. 999-1011 ISSN 0365-2556 R&D Projects: GA AV ČR Global Seismic Hazard Assessment Program (GSHAP) - project of the UN International Decade of Natural Disaster Reduction and International Litosphere Program. Subject RIV: DC - Siesmology, Volcanology, Earth Structure

Use of Citizen Science and Social Media to Improve Wind Hazard and Damage Characterization

Science.gov (United States)

Lombardo, F.; Meidani, H.

2017-12-01

Windstorm losses are significant in the U.S. annually and cause damage worldwide. A large percentage of losses are caused by localized events (e.g., tornadoes). In order to better mitigate these losses improvement is needed in understanding the hazard characteristics and physical damage. However, due to the small-scale nature of these events the resolution of the dedicated measuring network does not capture most occurrences. As a result damage-based assessments are sometimes used to gauge intensity. These damage assessments often suffer from a lack of available manpower, inability to arrive at the scene rapidly and difficulty accessing a damaged site. The use and rapid dissemination of social media, the power of crowds engaged in scientific endeavors, and the public's awareness of their vulnerabilities point to a paradigm shift in how hazards can be sensed in a rapid manner. In this way, `human-sensor' data has the potential to radically improve fundamental understanding of hazard and disasters and resolve some of the existing challenges in wind hazard and damage characterization. Data from social media outlets such as Twitter have been used to aid in damage assessments from hazards such as flood and earthquake, however, the reliability and uncertainty of participatory sensing has been questioned and has been called the `biggest challenge' for its sustained use. This research proposes to investigate the efficacy of both citizen science applications and social media data to represent wind hazards and associated damage. Research has focused on a two-phase approach: 1) to have citizen scientists perform their own `damage survey' (i.e., questionnaire) with known damage to assess uncertainty in estimation and 2) downloading and analysis of social media text and imagery streams to ascertain the possibility of performing `unstructured damage surveys'. Early results have shown that the untrained public can estimate tornado damage levels in residential structures with some

Use of the t-distribution to construct seismic hazard curves for seismic probabilistic safety assessments

Energy Technology Data Exchange (ETDEWEB)

Yee, Eric [KEPCO International Nuclear Graduate School, Dept. of Nuclear Power Plant Engineering, Ulsan (Korea, Republic of)

2017-03-15

Seismic probabilistic safety assessments are used to help understand the impact potential seismic events can have on the operation of a nuclear power plant. An important component to seismic probabilistic safety assessment is the seismic hazard curve which shows the frequency of seismic events. However, these hazard curves are estimated assuming a normal distribution of the seismic events. This may not be a strong assumption given the number of recorded events at each source-to-site distance. The use of a normal distribution makes the calculations significantly easier but may underestimate or overestimate the more rare events, which is of concern to nuclear power plants. This paper shows a preliminary exploration into the effect of using a distribution that perhaps more represents the distribution of events, such as the t-distribution to describe data. The integration of a probability distribution with potentially larger tails basically pushes the hazard curves outward, suggesting a different range of frequencies for use in seismic probabilistic safety assessments. Therefore the use of a more realistic distribution results in an increase in the frequency calculations suggesting rare events are less rare than thought in terms of seismic probabilistic safety assessment. However, the opposite was observed with the ground motion prediction equation considered.

Use of the t-distribution to construct seismic hazard curves for seismic probabilistic safety assessments

International Nuclear Information System (INIS)

Yee, Eric

2017-01-01

Seismic probabilistic safety assessments are used to help understand the impact potential seismic events can have on the operation of a nuclear power plant. An important component to seismic probabilistic safety assessment is the seismic hazard curve which shows the frequency of seismic events. However, these hazard curves are estimated assuming a normal distribution of the seismic events. This may not be a strong assumption given the number of recorded events at each source-to-site distance. The use of a normal distribution makes the calculations significantly easier but may underestimate or overestimate the more rare events, which is of concern to nuclear power plants. This paper shows a preliminary exploration into the effect of using a distribution that perhaps more represents the distribution of events, such as the t-distribution to describe data. The integration of a probability distribution with potentially larger tails basically pushes the hazard curves outward, suggesting a different range of frequencies for use in seismic probabilistic safety assessments. Therefore the use of a more realistic distribution results in an increase in the frequency calculations suggesting rare events are less rare than thought in terms of seismic probabilistic safety assessment. However, the opposite was observed with the ground motion prediction equation considered

A European perspective on alternatives to animal testing for environmental hazard identification and risk assessment.

Science.gov (United States)

Scholz, Stefan; Sela, Erika; Blaha, Ludek; Braunbeck, Thomas; Galay-Burgos, Malyka; García-Franco, Mauricio; Guinea, Joaquin; Klüver, Nils; Schirmer, Kristin; Tanneberger, Katrin; Tobor-Kapłon, Marysia; Witters, Hilda; Belanger, Scott; Benfenati, Emilio; Creton, Stuart; Cronin, Mark T D; Eggen, Rik I L; Embry, Michelle; Ekman, Drew; Gourmelon, Anne; Halder, Marlies; Hardy, Barry; Hartung, Thomas; Hubesch, Bruno; Jungmann, Dirk; Lampi, Mark A; Lee, Lucy; Léonard, Marc; Küster, Eberhard; Lillicrap, Adam; Luckenbach, Till; Murk, Albertinka J; Navas, José M; Peijnenburg, Willie; Repetto, Guillermo; Salinas, Edward; Schüürmann, Gerrit; Spielmann, Horst; Tollefsen, Knut Erik; Walter-Rohde, Susanne; Whale, Graham; Wheeler, James R; Winter, Matthew J

2013-12-01

Tests with vertebrates are an integral part of environmental hazard identification and risk assessment of chemicals, plant protection products, pharmaceuticals, biocides, feed additives and effluents. These tests raise ethical and economic concerns and are considered as inappropriate for assessing all of the substances and effluents that require regulatory testing. Hence, there is a strong demand for replacement, reduction and refinement strategies and methods. However, until now alternative approaches have only rarely been used in regulatory settings. This review provides an overview on current regulations of chemicals and the requirements for animal tests in environmental hazard and risk assessment. It aims to highlight the potential areas for alternative approaches in environmental hazard identification and risk assessment. Perspectives and limitations of alternative approaches to animal tests using vertebrates in environmental toxicology, i.e. mainly fish and amphibians, are discussed. Free access to existing (proprietary) animal test data, availability of validated alternative methods and a practical implementation of conceptual approaches such as the Adverse Outcome Pathways and Integrated Testing Strategies were identified as major requirements towards the successful development and implementation of alternative approaches. Although this article focusses on European regulations, its considerations and conclusions are of global relevance. Copyright © 2013 Elsevier Inc. All rights reserved.

DOE fundamentals handbook: Chemistry

International Nuclear Information System (INIS)

1993-01-01

The Chemistry Handbook was developed to assist nuclear facility operating contractors in providing operators, maintenance personnel, and the technical staff with the necessary fundamentals training to ensure a basic understanding of chemistry. The handbook includes information on the atomic structure of matter; chemical bonding; chemical equations; chemical interactions involved with corrosion processes; water chemistry control, including the principles of water treatment; the hazards of chemicals and gases, and basic gaseous diffusion processes. This information will provide personnel with a foundation for understanding the chemical properties of materials and the way these properties can impose limitations on the operation of equipment and systems

Flood Hazard Assessment for the Savannah River Site

International Nuclear Information System (INIS)

Chen, K.F.

2000-01-01

A method was developed to determine the probabilistic flood elevation curves for certain Savannah River Site (SRS) facilities. This paper presents the method used to determine the probabilistic flood elevation curve for F-Area due to runoff from the Upper Three Runs basin. Department of Energy (DOE) Order 420.1, Facility Safety, outlines the requirements for Natural Phenomena Hazard (NPH) mitigation for new and existing DOE facilities. The NPH considered in this paper is flooding. The facility-specific probabilistic flood hazard curve defines as a function of water elevation the annual probability of occurrence or the return period in years. Based on facility-specific probabilistic flood hazard curves and the nature of facility operations (e.g., involving hazardous or radioactive materials), facility managers can design permanent or temporary devices to prevent the propagation of flood on site, and develop emergency preparedness plans to mitigate the consequences of floods. A method was developed to determine the probabilistic flood hazard curves for SRS facilities. The flood hazard curves for the SRS F-Area due to flooding in the Upper Three Runs basin are presented in this paper

Discriminating Talent Identified Junior Australian Footballers Using a Fundamental Gross Athletic Movement Assessment

Science.gov (United States)

Woods, Carl T.; Banyard, Harry G.; McKeown, Ian; Fransen, Job; Robertson, Sam

2016-01-01

Talent identification (TID) is a pertinent component of the sports sciences, affording practitioners the opportunity to target developmental interventions to a select few; optimising financial investments. However, TID is multi-componential, requiring the recognition of immediate and prospective performance. The measurement of athletic movement skill may afford practitioners insight into the latter component given its augmented relationship with functional sport specific qualities. It is currently unknown whether athletic movement skill is a discriminant quality in junior Australian football (AF). This study aimed to discriminate talent identified junior AF players from their non-talent identified counterparts using a fundamental gross athletic movement assessment. From a total of 50 under 18 (U18) AF players; two groups were classified a priori based on selection level; talent identified (n = 25; state academy representatives) and non-talent identified (n = 25; state-based competition representatives). Players performed a fundamental gross athletic movement assessment based on the Athletic Ability Assessment (AAA), consisting of an overhead squat, double lunge (left and right legs), single leg Romanian deadlift (left and right legs), and a push up (six movement criterions). Movements were scored across three assessment points using a three-point scale (resulting in a possible score of nine for each movement). A multivariate analysis of variance revealed significant between group effects on four of the six movement criterions (d = 0.56 – 0.87; p = 0.01 – 0.02). Binary logistic regression models and a receiver operating characteristic curve inspection revealed that the overhead squat score provided the greatest group discrimination (β(SE) = -0.89(0.44); p talent identified and non-talent identified groups, respectively. Results support the integration of this assessment into contemporary talent identification approaches in junior AF, as it may provide coaches

Some relevant parameters for assessing fire hazards of combustible mine materials using laboratory scale experiments.

Science.gov (United States)

Litton, Charles D; Perera, Inoka E; Harteis, Samuel P; Teacoach, Kara A; DeRosa, Maria I; Thomas, Richard A; Smith, Alex C

2018-04-15

When combustible materials ignite and burn, the potential for fire growth and flame spread represents an obvious hazard, but during these processes of ignition and flaming, other life hazards present themselves and should be included to ensure an effective overall analysis of the relevant fire hazards. In particular, the gases and smoke produced both during the smoldering stages of fires leading to ignition and during the advanced flaming stages of a developing fire serve to contaminate the surrounding atmosphere, potentially producing elevated levels of toxicity and high levels of smoke obscuration that render the environment untenable. In underground mines, these hazards may be exacerbated by the existing forced ventilation that can carry the gases and smoke to locations far-removed from the fire location. Clearly, materials that require high temperatures (above 1400 K) and that exhibit low mass loss during thermal decomposition, or that require high heat fluxes or heat transfer rates to ignite represent less of a hazard than materials that decompose at low temperatures or ignite at low levels of heat flux. In order to define and quantify some possible parameters that can be used to assess these hazards, small-scale laboratory experiments were conducted in a number of configurations to measure: 1) the toxic gases and smoke produced both during non-flaming and flaming combustion; 2) mass loss rates as a function of temperature to determine ease of thermal decomposition; and 3) mass loss rates and times to ignition as a function of incident heat flux. This paper describes the experiments that were conducted, their results, and the development of a set of parameters that could possibly be used to assess the overall fire hazard of combustible materials using small scale laboratory experiments.

Internal dosimetry hazard and risk assessments: methods and applications

International Nuclear Information System (INIS)

Roberts, G.A.

2006-01-01

Routine internal dose exposures are typically (in the UK nuclear industry) less than external dose exposures: however, the costs of internal dosimetry monitoring programmes can be significantly greater than those for external dosimetry. For this reason decisions on when to apply routine monitoring programmes, and the nature of these programmes, can be more critical than for external dosimetry programmes. This paper describes various methods for performing hazard and risk assessments which are being developed by RWE NUKEM Limited Approved Dosimetry Services to provide an indication when routine internal dosimetry monitoring should be considered. (author)

Changing tides: Adaptive monitoring, assessment, and management of pharmaceutical hazards in the environment through time.

Science.gov (United States)

Gaw, Sally; Brooks, Bryan W

2016-04-01

Pharmaceuticals are ubiquitous contaminants in aquatic ecosystems. Adaptive monitoring, assessment, and management programs will be required to reduce the environmental hazards of pharmaceuticals of concern. Potentially underappreciated factors that drive the environmental dose of pharmaceuticals include regulatory approvals, marketing campaigns, pharmaceutical subsidies and reimbursement schemes, and societal acceptance. Sales data for 5 common antidepressants (duloxetine [Cymbalta], escitalopram [Lexapro], venlafaxine [Effexor], bupropion [Wellbutrin], and sertraline [Zoloft]) in the United States from 2004 to 2008 were modeled to explore how environmental hazards in aquatic ecosystems changed after patents were obtained or expired. Therapeutic hazard ratios for Effexor and Lexapro did not exceed 1; however, the therapeutic hazard ratio for Zoloft declined whereas the therapeutic hazard ratio for Cymbalta increased as a function of patent protection and sale patterns. These changes in therapeutic hazard ratios highlight the importance of considering current and future drivers of pharmaceutical use when prioritizing pharmaceuticals for water quality monitoring programs. When urban systems receiving discharges of environmental contaminants are examined, water quality efforts should identify, prioritize, and select target analytes presently in commerce for effluent monitoring and surveillance. © 2015 SETAC.

Use of risk to resolve conflicts in assessing hazards at mixed-waste sites

International Nuclear Information System (INIS)

Rechard, R.P.; Chu, M.S.Y.

1991-01-01

Two main issues contribute to the assessment of health hazard from mixed waste: the scientific methods to assess these materials and the legislative and regulatory control of these materials. This paper is primarily concerned with the scientific method of assessing hazards from mixed waste (i.e., carcinogenic chemicals, noncarcinogenic chemicals, and radioactive material). This paper discusses SRS, a Site Ranking System, and its use of risk concepts to avoid introducing new inconsistencies when ranking mixed-waste sites. SRS ranks each site by scoring factors that influence the human health risk. The factors are (1) the potentially exposed population, (2) the average amount of exposure to the waste, and (3) the toxicity of the waste. The relative risk of a release is measured as the product of these three factors. The third factor, toxicity, is indexed with a single score, but because methods of measuring toxicity differ for carcinogenic chemicals, noncarcinogenic chemicals, and radionuclides, comparison can be difficult; hence, this paper also summarizes the logic and assumptions used to make toxicity comparisons in SRS. As may be expected, results from a ranking scheme based on risk are different from results generated by the original Hazard Ranking System (HRS), used by the Environmental Protection Agency. This paper briefly discusses these differences for five Superfund sites (no mixed waste). The legislative and regulatory control of these materials to protect human health is also discussed. 37 refs., 1 tab

Recent achievements of the neo-deterministic seismic hazard assessment in the CEI region

International Nuclear Information System (INIS)

Panza, G.F.; Vaccari, F.; Kouteva, M.

2008-03-01

A review of the recent achievements of the innovative neo-deterministic approach for seismic hazard assessment through realistic earthquake scenarios has been performed. The procedure provides strong ground motion parameters for the purpose of earthquake engineering, based on the deterministic seismic wave propagation modelling at different scales - regional, national and metropolitan. The main advantage of this neo-deterministic procedure is the simultaneous treatment of the contribution of the earthquake source and seismic wave propagation media to the strong motion at the target site/region, as required by basic physical principles. The neo-deterministic seismic microzonation procedure has been successfully applied to numerous metropolitan areas all over the world in the framework of several international projects. In this study some examples focused on CEI region concerning both regional seismic hazard assessment and seismic microzonation of the selected metropolitan areas are shown. (author)

Impact of earthquake source complexity and land elevation data resolution on tsunami hazard assessment and fatality estimation

Science.gov (United States)

Muhammad, Ario; Goda, Katsuichiro

2018-03-01

This study investigates the impact of model complexity in source characterization and digital elevation model (DEM) resolution on the accuracy of tsunami hazard assessment and fatality estimation through a case study in Padang, Indonesia. Two types of earthquake source models, i.e. complex and uniform slip models, are adopted by considering three resolutions of DEMs, i.e. 150 m, 50 m, and 10 m. For each of the three grid resolutions, 300 complex source models are generated using new statistical prediction models of earthquake source parameters developed from extensive finite-fault models of past subduction earthquakes, whilst 100 uniform slip models are constructed with variable fault geometry without slip heterogeneity. The results highlight that significant changes to tsunami hazard and fatality estimates are observed with regard to earthquake source complexity and grid resolution. Coarse resolution (i.e. 150 m) leads to inaccurate tsunami hazard prediction and fatality estimation, whilst 50-m and 10-m resolutions produce similar results. However, velocity and momentum flux are sensitive to the grid resolution and hence, at least 10-m grid resolution needs to be implemented when considering flow-based parameters for tsunami hazard and risk assessments. In addition, the results indicate that the tsunami hazard parameters and fatality number are more sensitive to the complexity of earthquake source characterization than the grid resolution. Thus, the uniform models are not recommended for probabilistic tsunami hazard and risk assessments. Finally, the findings confirm that uncertainties of tsunami hazard level and fatality in terms of depth, velocity and momentum flux can be captured and visualized through the complex source modeling approach. From tsunami risk management perspectives, this indeed creates big data, which are useful for making effective and robust decisions.

On the fundamentals of nuclear reactor safety assessment. Inherent threats and their implications

Energy Technology Data Exchange (ETDEWEB)

Hyvaerinen, J. [Finnish Centre for Radiation and Nuclear Safety, Helsinki (Finland). Nuclear Safety Dept.

1996-12-01

The thesis addresses some fundamental questions related to implementation and assessment of nuclear safety. The safety principles and assessment methods are described, followed by descriptions of selected novel technical challenges to nuclear safety. The novel challenges encompass a wide variety of technical issues, thus providing insights on the limitations of conventional safety assessment methods. Study of the limitations suggests means to improve nuclear reactor design criteria and safety assessment practices. The novel safety challenges discussed are (1) inherent boron dilution in PWRs, (2) metallic insulation performance with respect to total loss of emergency cooling systems in a loss-of-coolant accident, and (3) horizontal steam generator heat transfer performance at natural circulation conditions. (50 refs.).

On the fundamentals of nuclear reactor safety assessment. Inherent threats and their implications

International Nuclear Information System (INIS)

Hyvaerinen, J.

1996-12-01

The thesis addresses some fundamental questions related to implementation and assessment of nuclear safety. The safety principles and assessment methods are described, followed by descriptions of selected novel technical challenges to nuclear safety. The novel challenges encompass a wide variety of technical issues, thus providing insights on the limitations of conventional safety assessment methods. Study of the limitations suggests means to improve nuclear reactor design criteria and safety assessment practices. The novel safety challenges discussed are (1) inherent boron dilution in PWRs, (2) metallic insulation performance with respect to total loss of emergency cooling systems in a loss-of-coolant accident, and (3) horizontal steam generator heat transfer performance at natural circulation conditions. (50 refs.)

Mapping basin-wide subaquatic slope failure susceptibility as a tool to assess regional seismic and tsunami hazards

Science.gov (United States)

Strasser, Michael; Hilbe, Michael; Anselmetti, Flavio S.

2010-05-01

With increasing awareness of oceanic geohazards, submarine landslides are gaining wide attention because of their catastrophic impacts on both offshore infrastructures (e.g. pipelines, cables and platforms) and coastal areas (e.g. landslide-induced tsunamis). They also are of great interest because they can be directly related to primary trigger mechanisms including earthquakes, rapid sedimentation, gas release, glacial and tidal loading, wave action, or clathrate dissociation, many of which represent potential geohazards themselves. In active tectonic environments, for instance, subaquatic landslide deposits can be used to make inferences regarding the hazard derived from seismic activity. Enormous scientific and economic efforts are thus being undertaken to better determine and quantify causes and effects of natural hazards related to subaquatic landslides. In order to achieve this fundamental goal, the detailed study of past events, the assessment of their recurrence intervals and the quantitative reconstruction of magnitudes and intensities of both causal and subsequent processes and impacts are key requirements. Here we present data and results from a study using fjord-type Lake Lucerne in central Switzerland as a "model ocean" to test a new concept for the assessment of regional seismic and tsunami hazard by basin-wide mapping of critical slope stability conditions for subaquatic landslide initiation. Previously acquired high-resolution bathymetry and reflection seismic data as well as sedimentological and in situ geotechnical data, provide a comprehensive data base to investigate subaquatic landslides and related geohazards. Available data are implemented into a basin-wide slope model. In a Geographic Information System (GIS)-framework, a pseudo-static limit equilibrium infinite slope stability equation is solved for each model point representing reconstructed slope conditions at different times in the past, during which earthquake-triggered landslides

Assessment of Occupational Hazards, Health Problems and Safety ...

African Journals Online (AJOL)

UNIBEN

Background: Petrol station attendants encounter several hazards and health problems while working. This study was conducted to determine the occupational hazards, health ..... engineering conference on sustainable ... Industrial Health.

Assessment of Three Flood Hazard Mapping Methods: A Case Study of Perlis

Science.gov (United States)

Azizat, Nazirah; Omar, Wan Mohd Sabki Wan

2018-03-01

Flood is a common natural disaster and also affect the all state in Malaysia. Regarding to Drainage and Irrigation Department (DID) in 2007, about 29, 270 km2 or 9 percent of region of the country is prone to flooding. Flood can be such devastating catastrophic which can effected to people, economy and environment. Flood hazard mapping can be used is an important part in flood assessment to define those high risk area prone to flooding. The purposes of this study are to prepare a flood hazard mapping in Perlis and to evaluate flood hazard using frequency ratio, statistical index and Poisson method. The six factors affecting the occurrence of flood including elevation, distance from the drainage network, rainfall, soil texture, geology and erosion were created using ArcGIS 10.1 software. Flood location map in this study has been generated based on flooded area in year 2010 from DID. These parameters and flood location map were analysed to prepare flood hazard mapping in representing the probability of flood area. The results of the analysis were verified using flood location data in year 2013, 2014, 2015. The comparison result showed statistical index method is better in prediction of flood area rather than frequency ratio and Poisson method.

Protocols for the Investigation of Information Processing in Human Assessment of Fundamental Movement Skills.

Science.gov (United States)

Ward, Brodie J; Thornton, Ashleigh; Lay, Brendan; Rosenberg, Michael

2017-01-01

Fundamental movement skill (FMS) assessment remains an important tool in classifying individuals' level of FMS proficiency. The collection of FMS performances for assessment and monitoring has remained unchanged over the last few decades, but new motion capture technologies offer opportunities to automate this process. To achieve this, a greater understanding of the human process of movement skill assessment is required. The authors present the rationale and protocols of a project in which they aim to investigate the visual search patterns and information extraction employed by human assessors during FMS assessment, as well as the implementation of the Kinect system for FMS capture.

Chemical health risk assessment for hazardous and mixed waste management units at Lawrence Livermore National Laboratory

International Nuclear Information System (INIS)

1992-09-01

The Lawrence Livermore National Laboratory (LLNL) operates three Hazardous Waste Management Facilities with 24 associated waste management units for the treatment and storage of hazardous and mixed wastes. These wastes are generated by research programs and support operations. The storage and treatment units are presently operated under interim status in accordance with the requirements of the US Envirorunental Protection Agency (US EPA) and the Department of Toxic Substances Control (DTSC), a division of the California Envirorunental Protection Agency (Cal/EPA). As required by the California Hazardous Waste Control Act and the Resource Conservation and Recovery Act (RCRA), LLNL ha s applied for a Part B permit to continue operating the storage and waste treatment facilities. As part of this permitting process, LLNL is required to conduct a health risk assessment (HRA) to examine the potential health impacts to the surrounding community from continued storage and treatment of hazardous and mixed wastes. analysis document presents the results of this risk assessment. An analysis of maximum credible chemical accidents is also included in Section 7.0. This HRA was prepared in accordance with procedures set forth by the California Air Pollution Control Officers Association (CAPCOA) ''Air Toxics Assessment Manual,'' CAPCOA guidelines for preparing risk assessments under the Air Toxic ''Hot Spots'' Act (AB 2588) and requirements of the US EPA. By following these procedures, this risk assessment presents a conservative analysis of a hypothetical Maximally Exposed Individual (MEI) using many worst-case assumptions that will not apply to an actual individual. As such, the risk estimates presented should be regarded as a worst-case estimate of any actual risk that may be present

Hazardous waste research and development in the Pacific Basin

International Nuclear Information System (INIS)

Cirillo, R.R.; Carpenter, R.A.

1989-01-01

The effective management of hazardous waste is an issue that all countries of the Pacific Basin must address. By very rough estimates, almost 272 million metric tons of hazardous wastes are being generated every year in the region. While the data are not consistently defined and reported, they do indicate the extent of the problem. Increasing development brings along an increase in the rate of hazardous waste generation. On this basis, the developing countries of the region can be expected to experience some of the same problems of the developed countries as their economies become more industrialized. Fundamental problems are involved in the compilation of consistent hazardous-waste generation statistics in the Pacific Basin. One involves the definition of what constitutes hazardous waste

Rockfall hazard assessment integrating probabilistic physically based rockfall source detection (Norddal municipality, Norway).

Science.gov (United States)

Yugsi Molina, F. X.; Oppikofer, T.; Fischer, L.; Hermanns, R. L.; Taurisano, A.

2012-04-01

Traditional techniques to assess rockfall hazard are partially based on probabilistic analysis. Stochastic methods has been used for run-out analysis of rock blocks to estimate the trajectories that a detached block will follow during its fall until it stops due to kinetic energy loss. However, the selection of rockfall source areas is usually defined either by multivariate analysis or by field observations. For either case, a physically based approach is not used for the source area detection. We present an example of rockfall hazard assessment that integrates a probabilistic rockfall run-out analysis with a stochastic assessment of the rockfall source areas using kinematic stability analysis in a GIS environment. The method has been tested for a steep more than 200 m high rock wall, located in the municipality of Norddal (Møre og Romsdal county, Norway), where a large number of people are either exposed to snow avalanches, rockfalls, or debris flows. The area was selected following the recently published hazard mapping plan of Norway. The cliff is formed by medium to coarse-grained quartz-dioritic to granitic gneisses of Proterozoic age. Scree deposits product of recent rockfall activity are found at the bottom of the rock wall. Large blocks can be found several tens of meters away from the cliff in Sylte, the main locality in the Norddal municipality. Structural characterization of the rock wall was done using terrestrial laser scanning (TLS) point clouds in the software Coltop3D (www.terranum.ch), and results were validated with field data. Orientation data sets from the structural characterization were analyzed separately to assess best-fit probability density functions (PDF) for both dip angle and dip direction angle of each discontinuity set. A GIS-based stochastic kinematic analysis was then carried out using the discontinuity set orientations and the friction angle as random variables. An airborne laser scanning digital elevation model (ALS-DEM) with 1 m

Technical Guidance for Hazardous Analysis, Emergency Planning for Extremely Hazardous Substances

Science.gov (United States)

This current guide supplements NRT-1 by providing technical assistance to LEPCs to assess the lethal hazards related to potential airborne releases of extremely hazardous substances (EHSs) as designated under Section 302 of Title Ill of SARA.

Flood hazard assessment for the Savannah River Site

International Nuclear Information System (INIS)

Chen, K.F.

2000-01-01

A method was developed to determine the probabilistic flood elevation curves for certain Savannah River Site (SRS) facilities. This paper presents the method used to determine the probabilistic flood elevation curve for F-Area due to runoff from the Upper Three Runs basin. Department of Energy (DOE) Order 420.1, Facility Safety, outlines the requirements for Natural Phenomena Hazard (NPH) mitigation for new and existing DOE facilities. The NPH considered in this paper is flooding. The facility-specific probabilistic flood hazard curve defines as a function of water elevation the annual probability of occurrence or the return period in years. Based on facility-specific probabilistic flood hazard curves and the nature of facility operations (e.g., involving hazardous or radioactive materials), facility managers can design permanent or temporary devices to prevent the propagation of flood on site, and develop emergency preparedness plans to mitigate the consequences of floods. The flood hazard curves for the SRS F-Area due to flooding in the Upper Three Runs basin are presented in this paper

The Impact Hazard in the Context of Other Natural Hazards and Predictive Science

Science.gov (United States)

Chapman, C. R.

1998-09-01

The hazard due to impact of asteroids and comets has been recognized as analogous, in some ways, to other infrequent but consequential natural hazards (e.g. floods and earthquakes). Yet, until recently, astronomers and space agencies have felt no need to do what their colleagues and analogous agencies must do in order the assess, quantify, and communicate predictions to those with a practical interest in the predictions (e.g. public officials who must assess the threats, prepare for mitigation, etc.). Recent heightened public interest in the impact hazard, combined with increasing numbers of "near misses" (certain to increase as Spaceguard is implemented) requires that astronomers accept the responsibility to place their predictions and assessments in terms that may be appropriately considered. I will report on preliminary results of a multi-year GSA/NCAR study of "Prediction in the Earth Sciences: Use and Misuse in Policy Making" in which I have represented the impact hazard, while others have treated earthquakes, floods, weather, global climate change, nuclear waste disposal, acid rain, etc. The impact hazard presents an end-member example of a natural hazard, helping those dealing with more prosaic issues to learn from an extreme. On the other hand, I bring to the astronomical community some lessons long adopted in other cases: the need to understand the policy purposes of impact predictions, the need to assess potential societal impacts, the requirements to very carefully assess prediction uncertainties, considerations of potential public uses of the predictions, awareness of ethical considerations (e.g. conflicts of interest) that affect predictions and acceptance of predictions, awareness of appropriate means for publicly communicating predictions, and considerations of the international context (especially for a hazard that knows no national boundaries).

A Guide to the Application of Probability Risk Assessment Methodology and Hazard Risk Frequency Criteria as a Hazard Control for the Use of the Mobile Servicing System on the International Space Station

Science.gov (United States)

D'silva, Oneil; Kerrison, Roger

2013-09-01

A key feature for the increased utilization of space robotics is to automate Extra-Vehicular manned space activities and thus significantly reduce the potential for catastrophic hazards while simultaneously minimizing the overall costs associated with manned space. The principal scope of the paper is to evaluate the use of industry standard accepted Probability risk/safety assessment (PRA/PSA) methodologies and Hazard Risk frequency Criteria as a hazard control. This paper illustrates the applicability of combining the selected Probability risk assessment methodology and hazard risk frequency criteria, in order to apply the necessary safety controls that allow for the increased use of the Mobile Servicing system (MSS) robotic system on the International Space Station. This document will consider factors such as component failure rate reliability, software reliability, and periods of operation and dormancy, fault tree analyses and their effects on the probability risk assessments. The paper concludes with suggestions for the incorporation of existing industry Risk/Safety plans to create an applicable safety process for future activities/programs

Performance Assessment of Hazardous Air Pollutant (HAP)Free Chemical Paint Strippers on Military Coatings for Validation to Federal Specification TT-R-2918A

Science.gov (United States)

2016-03-01

ARL-TN-0742 ● MAR 2016 US Army Research Laboratory Performance Assessment of Hazardous Air Pollutant (HAP)–Free Chemical Paint...the originator. ARL-TN-0742 ● MAR 2016 US Army Research Laboratory Performance Assessment of Hazardous Air Pollutant (HAP...COVERED (From - To) 1–30 April 2014 4. TITLE AND SUBTITLE Performance Assessment of Hazardous Air Pollutant (HAP)–Free Chemical Paint Strippers

Assessment of occupational health and safety hazard exposures among working college students.

Science.gov (United States)

Balanay, Jo Anne G; Adesina, Adepeju; Kearney, Gregory D; Richards, Stephanie L

2014-01-01

Adolescents and young adults have higher injury rates than their adult counterparts in similar jobs. This study used the working college student population to assess health and safety hazards in the workplace, characterize related occupational diseases and injuries, and describe worker health/safety activities provided by employers. College students (≥17 years old) were assessed via online surveys about work history, workplace exposure to hazards, occupational diseases/injuries, and workplace health/safety activities. Approximately half (51%) of participants (n = 1,147) were currently employed at the time of the survey or had been employed while enrolled in college. Restaurants (other than fast food) were the most frequently reported work setting. The most reported workplace hazards included noise exposure and contact with hot liquids/surfaces. Twenty percent of working students experienced injury at work; some injuries were severe enough to limit students' normal activities for >3 days (30%) or require medical attention (44%). Men had significantly higher prevalence of injuries (P = 0.05) and near-misses (P safety training and half were given personal protective equipment (PPE) by their employers. Risk reduction from workplace injuries and illnesses among working college students may be achieved by implementing occupational health and safety (OHS) strategies including incorporation of OHS in the college curriculum, promotion of OHS by university/college student health services, and improving awareness of OHS online resources among college students, employers, and educators. © 2013 Wiley Periodicals, Inc.

Seismic Hazard and risk assessment for Romania -Bulgaria cross-border region

Science.gov (United States)

Simeonova, Stela; Solakov, Dimcho; Alexandrova, Irena; Vaseva, Elena; Trifonova, Petya; Raykova, Plamena

2016-04-01

Among the many kinds of natural and man-made disasters, earthquakes dominate with regard to their social and economical impact on the urban environment. Global seismic hazard and vulnerability to earthquakes are steadily increasing as urbanization and development occupy more areas that are prone to effects of strong earthquakes. The assessment of the seismic hazard and risk is particularly important, because it provides valuable information for seismic safety and disaster mitigation, and it supports decision making for the benefit of society. Romania and Bulgaria, situated in the Balkan Region as a part of the Alpine-Himalayan seismic belt, are characterized by high seismicity, and are exposed to a high seismic risk. Over the centuries, both countries have experienced strong earthquakes. The cross-border region encompassing the northern Bulgaria and southern Romania is a territory prone to effects of strong earthquakes. The area is significantly affected by earthquakes occurred in both countries, on the one hand the events generated by the Vrancea intermediate-depth seismic source in Romania, and on the other hand by the crustal seismicity originated in the seismic sources: Shabla (SHB), Dulovo, Gorna Orjahovitza (GO) in Bulgaria. The Vrancea seismogenic zone of Romania is a very peculiar seismic source, often described as unique in the world, and it represents a major concern for most of the northern part of Bulgaria as well. In the present study the seismic hazard for Romania-Bulgaria cross-border region on the basis of integrated basic geo-datasets is assessed. The hazard results are obtained by applying two alternative approaches - probabilistic and deterministic. The MSK64 intensity (MSK64 scale is practically equal to the new EMS98) is used as output parameter for the hazard maps. We prefer to use here the macroseismic intensity instead of PGA, because it is directly related to the degree of damages and, moreover, the epicentral intensity is the original

Barrow hazards survey

International Nuclear Information System (INIS)

1980-06-01

Following a series of public meetings at which PERG presented the results of a literature review and site specific accident study of the hazards of the maritime transport of spent nuclear reactor fuel to Barrow (en route to the Windscale reprocessing works), PERG was requested by the Planning Committee of Barrow Town Council to prepare an assessment of the interaction of the hazards arising from the concentration of nuclear activities in the area with those of a proposed gas-terminal. This report presents a preliminary review of the Environmental Impact Assessments prepared by the Borough Surveyor and a critical appraisal of the hazard analyses undertaken by the Health and Safety Executive, and the consultants to Cumbria County Council on this matter, the Safety and Reliability Directorate of the United Kingdom Atomic Energy Authority. After a general and historical introduction, the document continues under the following headings: a description of the hazards (BNFL spent fuel shipments; the gas terminal; gas condensate storage; the Vickers shipyard (involving nuclear powered submarines)); the interaction of hazards; planning implications and democratic decisions; recommendations. (U.K.)

Tsunami hazard assessment along Diba-Oman and Diba-Al-Emirates coasts

Directory of Open Access Journals (Sweden)

El-Hussain Issa

2017-01-01

Full Text Available Tsunami is among the most devastating natural hazards phenomenon responsible for significant loss of life and property throughout history. The Sultanate of Oman and United Arab Emirates are among the Indian Ocean countries that were subjected to one confirmed tsunami in November 27, 1945 due to an Mw 8.1 earthquake in Makran Subduction Zone. In this study, we present preliminary deterministic tsunami hazard assessment for the coasts of Diba Oman and Diba Al-Emirates, which are located on the western coast of the Oman Sea. The tsunami vulnerability of these cities increases due to the construction of many critical infrastructures and urban concentration along their coasts. Therefore, tsunami hazard assessment is necessary to mitigate the risk on the socio-economic system and sustainable developments. The major known source of tsunamis able to impact both coasts of Oman and United Arab Emirates is the Makran Subduction Zone (MSZ which extends for approximately 900 km. The deterministic approach uses specific scenarios considering the maximum credible earthquakes occurring in the MSZ and computes the ensuing tsunami impact in the coasts of the study area. The maximum wave height graphs and inundation maps are obtained for tsunami scenarios caused by 8.8 earthquake magnitude in eastern MSZ and 8.2 magnitude from western MSZ. The Mw8.8 eastern MSZ causes a maximum inundation distance of 447 meters and a maximum flow depth of 1.37 meter. Maximum inundation distance larger than 420 meters occurs due to the Mw8.2 western MSZ scenario. For this scenario, numerical simulations show a maximum flow depth of about 2.34 meters.

Current Knowledge on the Use of Computational Toxicology in Hazard Assessment of Metallic Engineered Nanomaterials.

Science.gov (United States)

Chen, Guangchao; Peijnenburg, Willie; Xiao, Yinlong; Vijver, Martina G

2017-07-12

As listed by the European Chemicals Agency, the three elements in evaluating the hazards of engineered nanomaterials (ENMs) include the integration and evaluation of toxicity data, categorization and labeling of ENMs, and derivation of hazard threshold levels for human health and the environment. Assessing the hazards of ENMs solely based on laboratory tests is time-consuming, resource intensive, and constrained by ethical considerations. The adoption of computational toxicology into this task has recently become a priority. Alternative approaches such as (quantitative) structure-activity relationships ((Q)SAR) and read-across are of significant help in predicting nanotoxicity and filling data gaps, and in classifying the hazards of ENMs to individual species. Thereupon, the species sensitivity distribution (SSD) approach is able to serve the establishment of ENM hazard thresholds sufficiently protecting the ecosystem. This article critically reviews the current knowledge on the development of in silico models in predicting and classifying the hazard of metallic ENMs, and the development of SSDs for metallic ENMs. Further discussion includes the significance of well-curated experimental datasets and the interpretation of toxicity mechanisms of metallic ENMs based on reported models. An outlook is also given on future directions of research in this frontier.

Assessing Landslide Hazard Using Artificial Neural Network

DEFF Research Database (Denmark)

Farrokhzad, Farzad; Choobbasti, Asskar Janalizadeh; Barari, Amin

2011-01-01

failure" which is main concentration of the current research and "liquefaction failure". Shear failures along shear planes occur when the shear stress along the sliding surfaces exceed the effective shear strength. These slides have been referred to as landslide. An expert system based on artificial...... and factor of safety. It can be stated that the trained neural networks are capable of predicting the stability of slopes and safety factor of landslide hazard in study area with an acceptable level of confidence. Landslide hazard analysis and mapping can provide useful information for catastrophic loss...... reduction, and assist in the development of guidelines for sustainable land use planning. The analysis is used to identify the factors that are related to landslides and to predict the landslide hazard in the future based on such a relationship....

Thermal hazard assessment of TMCH mixed with inorganic acids

Directory of Open Access Journals (Sweden)

Yeh Chi-Tang

2018-01-01

Full Text Available 1,1-Bis(tert-butylperoxy-3,3,5-trimethylcyclohexane (TMCH is a typical peroxide with two peroxy groups that may runaway and/or explode due to mixing with inorganic acids, such as HCl, HNO3, H2SO4, or H3PO4. In this study, reactivities of TMCH mixed with the above inorganic acids were assessed by differential scanning calorimetry (DSC. Furthermore, data obtained by DSC, such as exothermic onset temperature (T0, maximum temperature (Tmax, and heat of decomposition (ΔHd could be employed to acquire thermal safety parameters. Moreover, thermal activity monitor III (TAM III was employed to investigate the thermal hazards while storing or transporting TMCH and TMCH mixed with four types of commonly used inorganic acids, here as HCl, HNO3, H2SO4, or H3PO4 under isothermal conditions. Mixing TMCH with those inorganic acids resulted in higherΔHd except H3PO4, and mixing TMCH with HCl clearly decreased T0. Therefore, the phenomena of mixing those incompatible materials with TMCH can be concluded as the worst cases in terms of contamination hazards during storage and transportation of TMCH.

Application of a complex assessment of landslide hazards in mountain regions

Directory of Open Access Journals (Sweden)

Kateryna E. Boyko

2017-09-01

Full Text Available The main regional factors of occurrence and activation of landslides within the mountain region were examined. As a result of study of recommendations made by experts, geologists, and gap analysis of existing methods of forecasting the landslide process, an algorithm of comprehensive assessment of landslide hazard areas based on the construction of models in a GIS environment was proposed. These models describe the spatial patterns of landslides. All factors determining the tendency of the studies area to the landslide process development were divided into actual factors, reflecting the regional peculiarities of the territory and forming the landslide-prone slopes (static model, as well as triggering factors, initiating the landslide process and determining its activity (dynamic model. The first cartographic model was built, showing the distribution of the deterministic indirect indicator of landslide hazard, i.e. stability index.

Overview of internal fire hazards aspects of ABWR design for United Kingdom

Energy Technology Data Exchange (ETDEWEB)

Yoshikawa, Kazuhiro; Kawai, Hiroki [Hitachi-GE Nuclear Energy, Ltd., Ibaraki (Japan)

2015-12-15

The ABWR (Advanced Boiling Water Reactor) is a generation III+ reactor, the most modern operational generation of nuclear power plants. The UK ABWR design is proposed for development and construction in the United Kingdom (UK), and under review by the Office for Nuclear Regulation (ONR) through Generic Design Assessment (GDA). The UK ABWR design has mainly two types of the safety system: ''preventing'' and ''mitigating'' a fault and their consequences. The prevention of internal hazards starts with design processes and procedures. These processes lead to limiting the sources of potential hazards. The mitigative safety systems are required to ensure the fundamental safety functions (FSFs): control of reactivity, Fuel cooling, long term heat removal, confinement/containment of radioactive materials, and others. Implementation of the safety philosophy is based upon redundant and diverse safety systems that deliver the FSFs. Three mechanical divisions are provided, each of which contains redundant systems, structures, and components (SSCs) capable of carrying out all the FSFs. The safety divisions are separated by robust barriers which act to contain a hazard in an affected division and prevent the spread of the hazard to a different division. The deterministic assessments and the hazard schedule argue that the rooms containing SSCs providing the FSFs are located in different fire safety divisions. The approach to maintaining the FSFs during and after internal fires is to ensure fires do not spread beyond that division to affect redundant equipment in other divisions. During the GDA process, it is demonstrated that generally barrier compartmentation (the divisional barrier walls, ceilings and floors) is sufficient to contain the postulated fires. The UK ABWR design has sufficient capability of withstanding the postulated internal fire hazard to achieve the FSFs. Further development is being undertaken with feedback in the GDA

Assessing the impact of hazardous waste on children's health: The exposome paradigm.

Science.gov (United States)

Sarigiannis, D A

2017-10-01

Assessment of the health impacts related to hazardous waste is a major scientific challenge with multiple societal implications. Most studies related to associations between hazardous waste and public health do not provide established of mechanistic links between environmental exposure and disease burden, resulting in ineffective waste management options. The exposome concept comes to overhaul the nature vs. nurture paradigm and embraces a world of dynamic interactions between environmental exposures, endogenous exposures and genetic expression in humans. In this context, the exposome paradigm provides a novel tool for holistic hazardous waste management. Waste streams and the related contamination of environmental media are not viewed in isolation, but rather as components of the expotype, the vector of exposures an individual is exposed to over time. Thus, a multi-route and multi-pathway exposure estimation can be performed setting a realistic basis for integrated health risk assessment. Waste management practices are thus assessed not only regarding their technological edge and efficacy but also their effects on human health at the individual and community level, considering intra-subject variability in the affected population. The effectiveness of the exposome approach is demonstrated in the case of Athens, the capital of Greece, where the health effects associated to long term and short term exposure to two major waste management facilities (landfill and plastic recycling) are presented. Using the exposome analysis tools, we confirmed that proximity to a landfill is critical for children neurodevelopment. However, this effect is significantly modified by parameters such as parental education level, socioeconomic status and nutrition. Proximity to a plastics recycling plant does not pose significant threats under normal operating conditions; yet, in the case of an accidental fire, release of persistent carcinogenic compounds (dioxins and furans) even for a

Hydrothermal Liquefaction Treatment Hazard Analysis Report

Energy Technology Data Exchange (ETDEWEB)

Lowry, Peter P. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wagner, Katie A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2016-09-12

Hazard analyses were performed to evaluate the modular hydrothermal liquefaction treatment system. The hazard assessment process was performed in 2 stages. An initial assessment utilizing Hazard Identification and Preliminary Hazards Analysis (PHA) techniques identified areas with significant or unique hazards (process safety-related hazards) that fall outside of the normal operating envelope of PNNL and warranted additional analysis. The subsequent assessment was based on a qualitative What-If analysis. The analysis was augmented, as necessary, by additional quantitative analysis for scenarios involving a release of hazardous material or energy with the potential for affecting the public. The following selected hazardous scenarios received increased attention: •Scenarios involving a release of hazardous material or energy, controls were identified in the What-If analysis table that prevent the occurrence or mitigate the effects of the release. •Scenarios with significant consequences that could impact personnel outside the immediate operations area, quantitative analyses were performed to determine the potential magnitude of the scenario. The set of “critical controls” were identified for these scenarios (see Section 4) which prevent the occurrence or mitigate the effects of the release of events with significant consequences.

Scientific Ocean Drilling Behind the Assessment of Geo-Hazards from Submarine Slides

Directory of Open Access Journals (Sweden)

Gemma Ercilla

2007-03-01

Full Text Available The workshop ‘Scientific Ocean Drilling Behind the Assessment of Geo-hazards from Submarine Slides’ was held on 25–27 October 2006 in Barcelona (Spain. Fifty mainly European scientists and industry representatives attended from a wide spectrum of disciplines such as geophysics, stratigraphy, sedimentology, paleoceanography, marinegeotechnology, geotechnical engineering, and tsunami modeling.

UK Hazard Assessment for a Laki-type Volcanic Eruption

Science.gov (United States)

Witham, Claire; Felton, Chris; Daud, Sophie; Aspinall, Willy; Braban, Christine; Loughlin, Sue; Hort, Matthew; Schmidt, Anja; Vieno, Massimo

2014-05-01

Following the impacts of the Eyjafjallajokull eruption in 2010, two types of volcanic eruption have been added to the UK Government's National Risk Register for Civil Emergencies. One of these, a large gas-rich volcanic eruption, was identified as a high impact natural hazard, one of the three highest priority natural hazards faced by the UK. This eruption scenario is typified by the Laki eruption in Iceland in 1783-1784. The Civil Contingency Secretariat (CCS) of the UK's Cabinet Office, responsible for Civil Protection in the UK, has since been working on quantifying the risk and better understanding its potential impacts. This involves cross-cutting work across UK Government departments and the wider scientific community in order to identify the capabilities needed to respond to an effusive eruption, to exercise the response and develop increased resilience where possible. As part of its current work, CCS has been working closely with the UK Met Office and other UK agencies and academics (represented by the co-authors and others) to generate and assess the impacts of a 'reasonable worst case scenario', which can be used for decision making and preparation in advance of an eruption. Information from the literature and the findings of an expert elicitation have been synthesised to determine appropriate eruption source term parameters and associated uncertainties. This scenario is then being used to create a limited ensemble of model simulations of the dispersion and chemical conversion of the emissions of volcanic gases during such an eruption. The UK Met Office's NAME Lagrangian dispersion model and the Centre for Ecology and Hydrology's EMEP4UK Eulerian model are both being used. Modelling outputs will address the likelihood of near-surface concentrations of sulphur and halogen species being above specified health thresholds. Concentrations at aviation relevant altitudes will also be evaluated, as well as the effects of acid deposition of volcanic species on

Hazards and hazard combinations relevant for the safety of nuclear power plants

Science.gov (United States)

Decker, Kurt; Brinkman, Hans; Raimond, Emmanuel

2017-04-01

The potential of the contemporaneous impact of different, yet causally related, hazardous events and event cascades on nuclear power plants is a major contributor to the overall risk of nuclear installations. In the aftermath of the Fukushima accident, which was caused by a combination of severe ground shaking by an earthquake, an earthquake-triggered tsunami and the disruption of the plants from the electrical grid by a seismically induced landslide, hazard combinations and hazard cascades moved into the focus of nuclear safety research. We therefore developed an exhaustive list of external hazards and hazard combinations which pose potential threats to nuclear installations in the framework of the European project ASAMPSAE (Advanced Safety Assessment: Extended PSA). The project gathers 31 partners from Europe, North Amerika and Japan. The list comprises of exhaustive lists of natural hazards, external man-made hazards, and a cross-correlation matrix of these hazards. The hazard list is regarded comprehensive by including all types of hazards that were previously cited in documents by IAEA, the Western European Nuclear Regulators Association (WENRA), and others. 73 natural hazards and 24 man-made external hazards are included. Natural hazards are grouped into seismotectonic hazards, flooding and hydrological hazards, extreme values of meteorological phenomena, rare meteorological phenomena, biological hazards / infestation, geological hazards, and forest fire / wild fire. The list of external man-made hazards includes industry accidents, military accidents, transportation accidents, pipeline accidents and other man-made external events. The large number of different hazards results in the extremely large number of 5.151 theoretically possible hazard combinations (not considering hazard cascades). In principle all of these combinations are possible to occur by random coincidence except for 82 hazard combinations that - depending on the time scale - are mutually

Geoethical and socio-political aspects of seismic and tsunami hazard assessment, quantification and mapping

Science.gov (United States)

Tinti, Stefano; Armigliato, Alberto

2016-04-01

Seismic hazard and, more recently, tsunami hazard assessments have been undertaken in several countries of the world and globally for the whole Earth planet with the aim of providing a scientifically sound basis to the engineers, technicians, urban and industrial planners, politicians, civil protection operators and in general to the authorities for devising rational risk mitigation strategies and corresponding adequate policies. The main point of this presentation is that the chief-value of all seismic and tsunami hazard studies (including theory, concept, quantification and mapping) resides in the social and political values of the provided products, which is a standpoint entailing a number of relevant geoethical implications. The most relevant implication regards geoscientists who are the subjects mainly involved in carrying out hazard evaluations. Viewed from the classical perspective, the main ethical obligations of geoscientists are restricted to performing hazard estimations in the best possible way from a scientific point of view, which means selecting the "best" available data, adopting sound theoretical models, making use of rigorous methods… What is outlined here, is that this is an insufficient minimalistic position, since it overlooks the basic socio-political and therefore practical value of the hazard-analysis final products. In other words, if one views hazard assessment as a production process leading from data and theories (raw data and production means) to hazard maps (products), the criterion to judge whether it is good or bad needs also to include the usability factor. Seismic and tsunami hazard reports and maps are products that should be usable, which means that they should meet user needs and requirements, and therefore they should be evaluated according to how much they are clearly understandable to, and appropriate for, making-decision users. In the traditional view of a science serving the society, one could represent the interaction

The evolution of global disaster risk assessments: from hazard to global change

Science.gov (United States)

Peduzzi, Pascal

2013-04-01

The perception of disaster risk as a dynamic process interlinked with global change is a fairly recent concept. It gradually emerged as an evolution from new scientific theories, currents of thinking and lessons learned from large disasters since the 1970s. The interest was further heighten, in the mid-1980s, by the Chernobyl nuclear accident and the discovery of the ozone layer hole, both bringing awareness that dangerous hazards can generate global impacts. The creation of the UN International Decade for Natural Disaster Reduction (IDNDR) and the publication of the first IPCC report in 1990 reinforced the interest for global risk assessment. First global risk models including hazard, exposure and vulnerability components were available since mid-2000s. Since then increased computation power and more refined datasets resolution, led to more numerous and sophisticated global risk models. This article presents a recent history of global disaster risk models, the current status of researches for the Global Assessment Report on Disaster Risk Reduction (GAR 2013) and future challenges and limitations for the development of next generation global disaster risk models.

Development of new geomagnetic storm ground response scaling factors for utilization in hazard assessments

Science.gov (United States)

Pulkkinen, A. A.; Bernabeu, E.; Weigel, R. S.; Kelbert, A.; Rigler, E. J.; Bedrosian, P.; Love, J. J.

2017-12-01

Development of realistic storm scenarios that can be played through the exposed systems is one of the key requirements for carrying out quantitative space weather hazards assessments. In the geomagnetically induced currents (GIC) and power grids context, these scenarios have to quantify the spatiotemporal evolution of the geoelectric field that drives the potentially hazardous currents in the system. In response to the Federal Energy Regulatory Commission (FERC) order 779, a team of scientists and engineers that worked under the auspices of North American Electric Reliability Corporation (NERC), has developed extreme geomagnetic storm and geoelectric field benchmark(s) that use various scaling factors that account for geomagnetic latitude and ground structure of the locations of interest. These benchmarks, together with the information generated in the National Space Weather Action Plan, are the foundation for the hazards assessments that the industry will be carrying out in response to the FERC order and under the auspices of the National Science and Technology Council. While the scaling factors developed in the past work were based on the best available information, there is now significant new information available for parts of the U.S. pertaining to the ground response to external geomagnetic field excitation. The significant new information includes the results magnetotelluric surveys that have been conducted over the past few years across the contiguous US and results from previous surveys that have been made available in a combined online database. In this paper, we distill this new information in the framework of the NERC benchmark and in terms of updated ground response scaling factors thereby allowing straightforward utilization in the hazard assessments. We also outline the path forward for improving the overall extreme event benchmark scenario(s) including generalization of the storm waveforms and geoelectric field spatial patterns.

Participatory health impact assessment for the development of local government regulation on hazard control

International Nuclear Information System (INIS)

Inmuong, Uraiwan; Rithmak, Panee; Srisookwatana, Soomol; Traithin, Nathathai; Maisuporn, Pornpun

2011-01-01

The Thai Public Health Act 1992 required the Thai local governments to issue respective regulations to take control of any possible health-hazard related activities, both from commercial and noncommercial sources. Since 1999, there has been centrally decentralized of power to a new form of local government establishment, namely Sub-district Administrative Organization (SAO). The SAO is asmall-scale local governing structure while its legitimate function is for community services, including control of health impact related activities. Most elected SAO administrators and officers are new and less experience with any of public health code of practice, particularly on health-hazard control. This action research attempted to introduce and apply a participatory health impact assessment (HIA) tool for the development of SAO health-hazard control regulation. The study sites were at Ban Meang and Kok See SAOs, Khon Kaen Province, Thailand, while all intervention activities conducted during May 2005-April 2006. A set of cooperative activities between researchers and community representatives were planned and organized by; surveying and identifying place and service base locally causing local environmental health problems, organizing community participatory workshops for drafting and proposing the health-hazard control regulation, and appropriate practices for health-hazard controlling measures. This action research eventually could successfully enable the SAO administrators and officers understanding of local environmental-related health problem, as well as development of imposed health-hazard control regulation for local community.

Assessing Natural Hazard Vulnerability Through Marmara Region Using GIS

Science.gov (United States)

Sabuncu, A.; Garagon Dogru, A.; Ozener, H.

2013-12-01

Natural hazards are natural phenomenon occured in the Earth's system that include geological and meteorological events such as earthquakes, floods, landslides, droughts, fires and tsunamis. The metropolitan cities are vulnerable to natural hazards due to their population densities, industrial facilities and proporties. The urban layout of the megacities are complex since industrial facilities are interference with residential area. The Marmara region is placed in North-western Turkey suffered from natural hazards (earthquakes, floods etc.) for years. After 1999 Kocaeli and Duzce earthquakes and 2009 Istanbul flash floods, dramatic number of casualities and economic losses were reported by the authorities. Geographic information systems (GIS) have substantial capacity in order to develop natural disaster management. As these systems provide more efficient and reliable analysis and evaluation of the data in the management, and also convenient and better solutions for the decision making before during and after the natural hazards. The Earth science data and socio-economic data can be integrated into a GIS as different layers. Additionally, satellite data are used to understand the changes pre and post the natural hazards. GIS is a powerful software for the combination of different type of digital data. A natural hazard database for the Marmara region provides all different types of digital data to the users. All proper data collection processing and analysing are critical to evaluate and identify hazards. The natural hazard database allows users to monitor, analyze and query past and recent disasters in the Marmara Region. The long term aim of this study is to develop geodatabase and identify the natural hazard vulnerabilities of the metropolitan cities.

A proposal for a test method for assessment of hazard property HP 12 (“Release of an acute toxic gas”) in hazardous waste classification - Experience from 49 waste

OpenAIRE

Hennebert , Pierre; Samaali , Ismahen; Molina , Pauline

2016-01-01

International audience; A stepwise method for assessment of the HP 12 is proposed and tested with 49 waste samples. The hazard property HP 12 is defined as “Release of an acute toxic gas”: waste which releases acute toxic gases (Acute Tox. 1, 2 or 3) in contact with water or an acid. When a waste contains a substance assigned to one of the following supplemental hazards EUH029, EUH031 and EUH032, it shall be classified as hazardous by HP 12 according to test methods or guidelines (EC, 2014a, ...

A Framework for Probabilistic Multi-Hazard Assessment of Rain-Triggered Lahars Using Bayesian Belief Networks

Directory of Open Access Journals (Sweden)

Pablo Tierz

2017-09-01

Full Text Available Volcanic water-sediment flows, commonly known as lahars, can often pose a higher threat to population and infrastructure than primary volcanic hazardous processes such as tephra fallout and Pyroclastic Density Currents (PDCs. Lahars are volcaniclastic flows of water, volcanic debris and entrained sediments that can travel long distances from their source, causing severe damage by impact and burial. Lahars are frequently triggered by intense or prolonged rainfall occurring after explosive eruptions, and their occurrence depends on numerous factors including the spatio-temporal rainfall characteristics, the spatial distribution and hydraulic properties of the tephra deposit, and the pre- and post-eruption topography. Modeling (and forecasting such a complex system requires the quantification of aleatory variability in the lahar triggering and propagation. To fulfill this goal, we develop a novel framework for probabilistic hazard assessment of lahars within a multi-hazard environment, based on coupling a versatile probabilistic model for lahar triggering (a Bayesian Belief Network: Multihaz with a dynamic physical model for lahar propagation (LaharFlow. Multihaz allows us to estimate the probability of lahars of different volumes occurring by merging varied information about regional rainfall, scientific knowledge on lahar triggering mechanisms and, crucially, probabilistic assessment of available pyroclastic material from tephra fallout and PDCs. LaharFlow propagates the aleatory variability modeled by Multihaz into hazard footprints of lahars. We apply our framework to Somma-Vesuvius (Italy because: (1 the volcano is strongly lahar-prone based on its previous activity, (2 there are many possible source areas for lahars, and (3 there is high density of population nearby. Our results indicate that the size of the eruption preceding the lahar occurrence and the spatial distribution of tephra accumulation have a paramount role in the lahar

History of Modern Earthquake Hazard Mapping and Assessment in California Using a Deterministic or Scenario Approach

Science.gov (United States)

Mualchin, Lalliana

2011-03-01

Modern earthquake ground motion hazard mapping in California began following the 1971 San Fernando earthquake in the Los Angeles metropolitan area of southern California. Earthquake hazard assessment followed a traditional approach, later called Deterministic Seismic Hazard Analysis (DSHA) in order to distinguish it from the newer Probabilistic Seismic Hazard Analysis (PSHA). In DSHA, seismic hazard in the event of the Maximum Credible Earthquake (MCE) magnitude from each of the known seismogenic faults within and near the state are assessed. The likely occurrence of the MCE has been assumed qualitatively by using late Quaternary and younger faults that are presumed to be seismogenic, but not when or within what time intervals MCE may occur. MCE is the largest or upper-bound potential earthquake in moment magnitude, and it supersedes and automatically considers all other possible earthquakes on that fault. That moment magnitude is used for estimating ground motions by applying it to empirical attenuation relationships, and for calculating ground motions as in neo-DSHA (Z uccolo et al., 2008). The first deterministic California earthquake hazard map was published in 1974 by the California Division of Mines and Geology (CDMG) which has been called the California Geological Survey (CGS) since 2002, using the best available fault information and ground motion attenuation relationships at that time. The California Department of Transportation (Caltrans) later assumed responsibility for printing the refined and updated peak acceleration contour maps which were heavily utilized by geologists, seismologists, and engineers for many years. Some engineers involved in the siting process of large important projects, for example, dams and nuclear power plants, continued to challenge the map(s). The second edition map was completed in 1985 incorporating more faults, improving MCE's estimation method, and using new ground motion attenuation relationships from the latest published

Developing a methodology for the national-scale assessment of rainfall-induced landslide hazard in a changing climate

Science.gov (United States)

Jurchescu, Marta; Micu, Dana; Sima, Mihaela; Bălteanu, Dan; Bojariu, Roxana; Dumitrescu, Alexandru; Dragotă, Carmen; Micu, Mihai; Senzaconi, Francisc

2017-04-01

Landslides together with earthquakes and floods represent the main natural hazards in Romania, causing major impacts to human activities. The RO-RISK (Disaster Risk Evaluation at a National Level) project is a flagship project aimed to strengthen risk prevention and management in Romania, by evaluating - among the specific risks in the country - landslide hazard and risk at a national level. Landslide hazard is defined as "the probability of occurrence within a specified period of time and within a given area of a landslide of a given magnitude" (Varnes 1984; Guzzetti et al. 1999). Nevertheless, most landslide ʿhazardʾ maps only consist in susceptibility (i.e. spatial probability) zonations without considering temporal or magnitude information on the hazard. This study proposes a methodology for the assessment of landslide hazard at the national scale on a scenario basis, while also considering changes in hazard patterns and levels under climate change conditions. A national landslide database consisting of more than 3,000 records has been analyzed against a meteorological observation dataset in order to assess the relationship between precipitation and landslides. Various extreme climate indices were computed in order to account for the different rainfall patterns able to prepare/trigger landslides (e.g. extreme levels of seasonal rainfall, 3-days rainfall or number of consecutive rainy days with different return periods). In order to derive national rainfall thresholds, i.e. valid for diverse climatic environments across the country, values in the parameter maps were rendered comparable by means of normalization with the mean annual precipitation and the rainy-day-normal. A hazard assessment builds on a frequency-magnitude relationship. In the current hazard scenario approach, frequency was kept constant for each single map, while the magnitude of the expected geomorphic event was modeled in relation to the distributed magnitude of the triggering factor. Given

Flood Hazard Assessment for the Savannah River Site

International Nuclear Information System (INIS)

Chen, K.F.

1999-01-01

'A method was developed to determine the probabilistic flood elevation curves for certain Savannah River Site (SRS) facilities. This paper presents the method used to determine the probabilistic flood elevation curve for F-Area due to runoff from the Upper Three Runs basin. Department of Energy (DOE) Order 420.1, Facility Safety, outlines the requirements for Natural Phenomena Hazard (NPH) mitigation for new and existing DOE facilities. The NPH considered in this paper is flooding. The facility-specific probabilistic flood hazard curve defines as a function of water elevation the annual probability of occurrence or the return period in years. Based on facility-specific probabilistic flood hazard curves and the nature of facility operations (e.g., involving hazardous or radioactive materials), facility managers can design permanent or temporary devices to prevent the propagation of flood on site, and develop emergency preparedness plans to mitigate the consequences of floods.'

Assessment of tsunami hazard for coastal areas of Shandong Province, China

Science.gov (United States)

Feng, Xingru; Yin, Baoshu

2017-04-01

Shandong province is located on the east coast of China and has a coastline of about 3100 km. There are only a few tsunami events recorded in the history of Shandong Province, but the tsunami hazard assessment is still necessary as the rapid economic development and increasing population of this area. The objective of this study was to evaluate the potential danger posed by tsunamis for Shandong Province. The numerical simulation method was adopted to assess the tsunami hazard for coastal areas of Shandong Province. The Cornell multi-grid coupled tsunami numerical model (COMCOT) was used and its efficacy was verified by comparison with three historical tsunami events. The simulated maximum tsunami wave height agreed well with the observational data. Based on previous studies and statistical analyses, multiple earthquake scenarios in eight seismic zones were designed, the magnitudes of which were set as the potential maximum values. Then, the tsunamis they induced were simulated using the COMCOT model to investigate their impact on the coastal areas of Shandong Province. The numerical results showed that the maximum tsunami wave height, which was caused by the earthquake scenario located in the sea area of the Mariana Islands, could reach up to 1.39 m off the eastern coast of Weihai city. The tsunamis from the seismic zones of the Bohai Sea, Okinawa Trough, and Manila Trench could also reach heights of >1 m in some areas, meaning that earthquakes in these zones should not be ignored. The inundation hazard was distributed primarily in some northern coastal areas near Yantai and southeastern coastal areas of Shandong Peninsula. When considering both the magnitude and arrival time of tsunamis, it is suggested that greater attention be paid to earthquakes that occur in the Bohai Sea. In conclusion, the tsunami hazard facing the coastal area of Shandong Province is not very serious; however, disasters could occur if such events coincided with spring tides or other

Endocrine effects of chemicals: aspects of hazard identification and human health risk assessment.

Science.gov (United States)

Dekant, Wolfgang; Colnot, Thomas

2013-12-16

Hazard and risk assessment of chemicals with endocrine activity is hotly debated due to claimed non-monotonous dose-response curves in the low-dose region. In hazard identification a clear definition of "endocrine disruptors" (EDs) is required; this should be based on the WHO/IPCS definition of EDs and on adverse effects demonstrated in intact animals or humans. Therefore, endocrine effects are a mode of action potentially resulting in adverse effects; any classification should not be based on a mode of action, but on adverse effects. In addition, when relying on adverse effects, most effects reported in the low-dose region will not qualify for hazard identification since most have little relation to an adverse effect. Non-monotonous dose-response curves that had been postulated from limited, exploratory studies could also not be reproduced in targeted studies with elaborate quality assurance. Therefore, regulatory agencies or advisory bodies continue to apply the safety-factor method or the concept of "margin-of-exposure" based on no observed adverse effect levels (NOAELs) in the risk assessment of chemicals with weak hormonal activity. Consistent with this approach, tolerable levels regarding human exposure have been defined for such chemicals. To conclusively support non-monotonous dose-response curves, targeted experiments with a sufficient number of animals, determination of adverse endpoints, adequate statistics and quality control would be required. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

Risk Assessment of Healthcare Waste by Preliminary Hazard Analysis Method

Directory of Open Access Journals (Sweden)

Pouran Morovati

2017-09-01

Full Text Available Introduction and purpose: Improper management of healthcare waste (HCW can pose considerable risks to human health and the environment and cause serious problems in developing countries such as Iran. In this study, we sought to determine the hazards of HCW in the public hospitals affiliated to Abadan School of Medicine using the preliminary hazard analysis (PHA method. Methods: In this descriptive and analytic study, health risk assessment of HCW in government hospitals affiliated to Abadan School of Medicine (4 public hospitals was carried out by using PHA in the summer of  2016. Results: We noted the high risk of sharps and infectious wastes. Considering the dual risk of injury and disease transmission, sharps were classified in the very high-risk group, and pharmaceutical and chemical and radioactive wastes were classified in the medium-risk group. Sharps posed the highest risk, while pharmaceutical and chemical wastes had the lowest risk. Among the various stages of waste management, the waste treatment stage was the most hazardous in all the studied hospitals. Conclusion: To diminish the risks associated with healthcare waste management in the studied hospitals, adequate training of healthcare workers and care providers, provision of suitable personal protective and transportation equipment, and supervision of the environmental health manager of hospitals should be considered by the authorities.  

Site-specific Seismic Hazard Assessment to Establish Elastic Design Properties for Oman Museum-Across Ages, Manah, Sultante of Oman

Science.gov (United States)

El Hussain, I. W.

2017-12-01

The current study provides a site specific deterministic seismic hazard assessment (DSHA) at the selected site for establishing the Oman Museum-Across Ages at Manah area, as a part of a comprehensive geotechnical and seismological plan to design the facilities accordingly. The DSHA first defines the seismic sources that might influence the site and assesses the maximum possible earthquake magnitude for each of them. By assuming each of these maximum earthquakes to occur at a location placing them at the closest distances to the site, the ground motion is predicted utilizing empirical ground motion prediction equations. The local site effects are performed by determining the fundamental frequency of the soft soil using HVSR technique and by estimating amplification spectra using the soil characteristics (mainly shear-wave velocity). Shear-wave velocity has been evaluated using the MASW technique. The maximum amplification value of 2.1 at spectral period 0.06 sec is observed at the ground surface, while the largest amplification value at the top of the conglomerate layer (at 5m depth) is 1.6 for a spectral period of 0.04 Sec. The maximum median 5% damped peak ground acceleration is found to be 0.263g at a spectral period of 0.1 sec. Keywords: DSHA; Site Effects; HVSR; MASW; PGA; Spectral Period

Assessment of groundwater contamination risk using hazard quantification, a modified DRASTIC model and groundwater value, Beijing Plain, China.

Science.gov (United States)

Wang, Junjie; He, Jiangtao; Chen, Honghan

2012-08-15

Groundwater contamination risk assessment is an effective tool for groundwater management. Most existing risk assessment methods only consider the basic contamination process based upon evaluations of hazards and aquifer vulnerability. In view of groundwater exploitation potentiality, including the value of contamination-threatened groundwater could provide relatively objective and targeted results to aid in decision making. This study describes a groundwater contamination risk assessment method that integrates hazards, intrinsic vulnerability and groundwater value. The hazard harmfulness was evaluated by quantifying contaminant properties and infiltrating contaminant load, the intrinsic aquifer vulnerability was evaluated using a modified DRASTIC model and the groundwater value was evaluated based on groundwater quality and aquifer storage. Two groundwater contamination risk maps were produced by combining the above factors: a basic risk map and a value-weighted risk map. The basic risk map was produced by overlaying the hazard map and the intrinsic vulnerability map. The value-weighted risk map was produced by overlaying the basic risk map and the groundwater value map. Relevant validation was completed by contaminant distributions and site investigation. Using Beijing Plain, China, as an example, thematic maps of the three factors and the two risks were generated. The thematic maps suggested that landfills, gas stations and oil depots, and industrial areas were the most harmful potential contamination sources. The western and northern parts of the plain were the most vulnerable areas and had the highest groundwater value. Additionally, both the basic and value-weighted risk classes in the western and northern parts of the plain were the highest, indicating that these regions should deserve the priority of concern. Thematic maps should be updated regularly because of the dynamic characteristics of hazards. Subjectivity and validation means in assessing the

The perception of hazards

International Nuclear Information System (INIS)

Fritzsche, A.F.

1986-01-01

The fourth chapter deals with the profusion of factors determining the differing assessment of hazards by our society. Subjective factors influencing risk perception comprise, among others, general knowledge and recognition of a hazard; the degree of voluntariness when taking the risk and its influencibility; the problem of large scale accidents; immediate and delayed results. Next to the objective and the subjective risks, the individual and the social or collective risks are assessed differently. The author dicusses in detail recent investigations into and study methods for the determination of risk perception, while eliminating systematic trends from subjective perception since common assessments are shared by whole groups of individuals time and again which allow a better understanding of today's handling of hazards. (HSCH) [de

Radiation protection. Scientific fundamentals, legal regulations, practical applications. Compendium

International Nuclear Information System (INIS)

Buchert, Guido; Gay, Juergen; Kirchner, Gerald; Michel, Rolf; Niggemann, Guenter; Schumann, Joerg; Wust, Peter; Jaehnert, Susanne; Strilek, Ralf; Martini, Ekkehard

2011-06-01

The compendium on radiation protection, scientific fundamentals, legal regulations and practical applications includes contributions to the following issues: (1) Effects and risk of ionizing radiation: fundamentals on effects and risk of ionizing radiation, news in radiation biology, advantages and disadvantages of screening investigations; (2) trends and legal regulations concerning radiation protection: development of European and national radiation protection laws, new regulations concerning X-rays, culture and ethics of radiation protection; (3) dosimetry and radiation measuring techniques: personal scanning using GHz radiation, new ''dose characteristics'' in practice, measuring techniques for the nuclear danger prevention and emergency hazard control; (4) radiation exposure in medicine: radiation exposure of modern medical techniques, heavy ion radiotherapy, deterministic and stochastic risks of the high-conformal photon radiotherapy, STEMO project - mobile CT for apoplectic stroke patients; (5) radiation exposure in technology: legal control of high-level radioactive sources, technical and public safety using enclosed radioactive sources for materials testing, radiation exposure in aviation, radon in Bavaria, NPP Fukushima-Daiichi - a status report; (6) radiation exposure in nuclear engineering: The Chernobyl accident - historical experiences or sustaining problem? European standards for radioactive waste disposal, radioactive material disposal in Germany risk assessment of ionizing and non-ionizing radiation (7) Case studies.

Assessment of occupational hazards, health problems and safety ...

African Journals Online (AJOL)

Background: Petrol station attendants encounter several hazards and health problems while working. This study was conducted to determine the ... Hazards reported included inhalation of petrol fumes 145 (67.4%), confrontation from customers 112 (52.1%) and noise 98 (45.6%). Health problems reported included ...

Combining computational models for landslide hazard assessment of Guantánamo province, Cuba

NARCIS (Netherlands)

Castellanos Abella, E.A.

2008-01-01

As part of the Cuban system for landslide disaster management, a methodology was developed for regional scale landslide hazard assessment, which is a combination of different models. The method was applied in Guantánamo province at 1:100 000 scale. The analysis started with an extensive aerial

Seismic hazard and risk assessment for large Romanian dams situated in the Moldavian Platform

Science.gov (United States)

Moldovan, Iren-Adelina; Popescu, Emilia; Otilia Placinta, Anica; Petruta Constantin, Angela; Toma Danila, Dragos; Borleanu, Felix; Emilian Toader, Victorin; Moldoveanu, Traian

2016-04-01

Besides periodical technical inspections, the monitoring and the surveillance of dams' related structures and infrastructures, there are some more seismic specific requirements towards dams' safety. The most important one is the seismic risk assessment that can be accomplished by rating the dams into seismic risk classes using the theory of Bureau and Ballentine (2002), and Bureau (2003), taking into account the maximum expected peak ground motions at the dams site - values obtained using probabilistic hazard assessment approaches (Moldovan et al., 2008), the structures vulnerability and the downstream risk characteristics (human, economical, historic and cultural heritage, etc) in the areas that might be flooded in the case of a dam failure. Probabilistic seismic hazard (PSH), vulnerability and risk studies for dams situated in the Moldavian Platform, starting from Izvorul Muntelui Dam, down on Bistrita and following on Siret River and theirs affluent will be realized. The most vulnerable dams will be studied in detail and flooding maps will be drawn to find the most exposed downstream localities both for risk assessment studies and warnings. GIS maps that clearly indicate areas that are potentially flooded are enough for these studies, thus giving information on the number of inhabitants and goods that may be destroyed. Geospatial servers included topography is sufficient to achieve them, all other further studies are not necessary for downstream risk assessment. The results will consist of local and regional seismic information, dams specific characteristics and locations, seismic hazard maps and risk classes, for all dams sites (for more than 30 dams), inundation maps (for the most vulnerable dams from the region) and possible affected localities. The studies realized in this paper have as final goal to provide the local emergency services with warnings of a potential dam failure and ensuing flood as a result of an large earthquake occurrence, allowing further

Current Knowledge on the Use of Computational Toxicology in Hazard Assessment of Metallic Engineered Nanomaterials

Directory of Open Access Journals (Sweden)

Guangchao Chen

2017-07-01

Full Text Available As listed by the European Chemicals Agency, the three elements in evaluating the hazards of engineered nanomaterials (ENMs include the integration and evaluation of toxicity data, categorization and labeling of ENMs, and derivation of hazard threshold levels for human health and the environment. Assessing the hazards of ENMs solely based on laboratory tests is time-consuming, resource intensive, and constrained by ethical considerations. The adoption of computational toxicology into this task has recently become a priority. Alternative approaches such as (quantitative structure–activity relationships ((QSAR and read-across are of significant help in predicting nanotoxicity and filling data gaps, and in classifying the hazards of ENMs to individual species. Thereupon, the species sensitivity distribution (SSD approach is able to serve the establishment of ENM hazard thresholds sufficiently protecting the ecosystem. This article critically reviews the current knowledge on the development of in silico models in predicting and classifying the hazard of metallic ENMs, and the development of SSDs for metallic ENMs. Further discussion includes the significance of well-curated experimental datasets and the interpretation of toxicity mechanisms of metallic ENMs based on reported models. An outlook is also given on future directions of research in this frontier.

Hazard Ranking Methodology for Assessing Health Impacts of Unconventional Natural Gas Development and Production: The Maryland Case Study.

Directory of Open Access Journals (Sweden)

Meleah D Boyle

Full Text Available The recent growth of unconventional natural gas development and production (UNGDP has outpaced research on the potential health impacts associated with the process. The Maryland Marcellus Shale Public Health Study was conducted to inform the Maryland Marcellus Shale Safe Drilling Initiative Advisory Commission, State legislators and the Governor about potential public health impacts associated with UNGDP so they could make an informed decision that considers the health and well-being of Marylanders. In this paper, we describe an impact assessment and hazard ranking methodology we used to assess the potential public health impacts for eight hazards associated with the UNGDP process. The hazard ranking included seven metrics: 1 presence of vulnerable populations (e.g. children under the age of 5, individuals over the age of 65, surface owners, 2 duration of exposure, 3 frequency of exposure, 4 likelihood of health effects, 5 magnitude/severity of health effects, 6 geographic extent, and 7 effectiveness of setbacks. Overall public health concern was determined by a color-coded ranking system (low, moderately high, and high that was generated based on the overall sum of the scores for each hazard. We provide three illustrative examples of applying our methodology for air quality and health care infrastructure which were ranked as high concern and for water quality which was ranked moderately high concern. The hazard ranking was a valuable tool that allowed us to systematically evaluate each of the hazards and provide recommendations to minimize the hazards.

[Application of occupational hazard risk index model in occupational health risk assessment in a decorative coating manufacturing enterprises].

Science.gov (United States)

He, P L; Zhao, C X; Dong, Q Y; Hao, S B; Xu, P; Zhang, J; Li, J G

2018-01-20

Objective: To evaluate the occupational health risk of decorative coating manufacturing enterprises and to explore the applicability of occupational hazard risk index model in the health risk assessment, so as to provide basis for the health management of enterprises. Methods: A decorative coating manufacturing enterprise in Hebei Province was chosen as research object, following the types of occupational hazards and contact patterns, the occupational hazard risk index model was used to evaluate occupational health risk factors of occupational hazards in the key positions of the decorative coating manufacturing enterprise, and measured with workplace test results and occupational health examination. Results: The positions of oily painters, water-borne painters, filling workers and packers who contacted noise were moderate harm. And positions of color workers who contacted chromic acid salts, oily painters who contacted butyl acetate were mild harm. Other positions were harmless. The abnormal rate of contacting noise in physical examination results was 6.25%, and the abnormality was not checked by other risk factors. Conclusion: The occupational hazard risk index model can be used in the occupational health risk assessment of decorative coating manufacturing enterprises, and noise was the key harzard among occupational harzards in this enterprise.

Determination of lead and radioactivity in cosmetics products: Hazard assessment

Directory of Open Access Journals (Sweden)

Medhat Moustafa E.

2015-01-01

Full Text Available In the proposed work, an investigation on hazard assessment by lead element and natural radioactivity in cosmetic samples collected from various countries is presented. These samples were face powder, eyebrow paint and henna. The lead element in cosmetic samples was determined using particle-induced X-ray emission. Maximum natural radioactivity concentrations of 226Ra and 40K were found in khol and make-up cosmetic samples, respectively. The qualitative analysis of cosmetic samples showed that lead is the most toxic element found in eyebrow paint samples.

Discriminating Talent Identified Junior Australian Footballers Using a Fundamental Gross Athletic Movement Assessment.

Science.gov (United States)

Woods, Carl T; Banyard, Harry G; McKeown, Ian; Fransen, Job; Robertson, Sam

2016-09-01

Talent identification (TID) is a pertinent component of the sports sciences, affording practitioners the opportunity to target developmental interventions to a select few; optimising financial investments. However, TID is multi-componential, requiring the recognition of immediate and prospective performance. The measurement of athletic movement skill may afford practitioners insight into the latter component given its augmented relationship with functional sport specific qualities. It is currently unknown whether athletic movement skill is a discriminant quality in junior Australian football (AF). This study aimed to discriminate talent identified junior AF players from their non-talent identified counterparts using a fundamental gross athletic movement assessment. From a total of 50 under 18 (U18) AF players; two groups were classified a priori based on selection level; talent identified (n = 25; state academy representatives) and non-talent identified (n = 25; state-based competition representatives). Players performed a fundamental gross athletic movement assessment based on the Athletic Ability Assessment (AAA), consisting of an overhead squat, double lunge (left and right legs), single leg Romanian deadlift (left and right legs), and a push up (six movement criterions). Movements were scored across three assessment points using a three-point scale (resulting in a possible score of nine for each movement). A multivariate analysis of variance revealed significant between group effects on four of the six movement criterions (d = 0.56 - 0.87; p = 0.01 - 0.02). Binary logistic regression models and a receiver operating characteristic curve inspection revealed that the overhead squat score provided the greatest group discrimination (β(SE) = -0.89(0.44); p talent identified and non-talent identified groups, respectively. Results support the integration of this assessment into contemporary talent identification approaches in junior AF, as it may provide coaches with

The effect of the sea on hazard assessment for tephra fallout at Campi Flegrei: a preliminary approach through the use of pyPHaz, an open tool to analyze and visualize probabilistic hazards

Science.gov (United States)

Tonini, Roberto; Sandri, Laura; Costa, Antonio; Selva, Jacopo

2014-05-01

Campi Flegrei (CF) is a large volcanic field located west of the Gulf of Naples, characterized by a wide and almost circular caldera which is partially submerged beneath the Gulf of Pozzuoli. It is known that the magma-water interaction is a key element to determine the character of submarine eruptions and their impact on the surrounding areas, but this phenomenon is still not well understood and it is rarely considered in hazard assessment. The aim of the present work is to present a preliminary study of the effect of the sea on the tephra fall hazard from CF on the municipality of Naples, by introducing a variability in the probability of tephra production according to the eruptive scale (defined on the basis of the erupted volume) and the depth of the opening submerged vents. Four different Probabilistic Volcanic Hazard Assessment (PVHA) models have been defined through the application of the model BET_VH at CF, by accounting for different modeling procedures and assumptions for the submerged part of the caldera. In particular, we take into account: 1) the effect of the sea as null, i.e. as if the water were not present; 2) the effect of the sea as a cap that totally blocks the explosivity of eruptions and consequently the tephra production; 3) an ensemble model between the two models described at the previous points 1) and 2); 4) a variable probability of tephra production depending on the depth of the submerged vent. The PVHA models are then input to pyPHaz, a tool developed and designed at INGV to visualize, analyze and merge into ensemble models PVHA's results and, potentially, any other kind of probabilistic hazard assessment, both natural and anthropic, in order to evaluate the importance of considering a variability among subaerial and submerged vents on tephra fallout hazard from CF in Naples. The analysis is preliminary and does not pretend to be exhaustive, but on one hand it represents a starting point for future works; on the other hand, it is a good

GIS-BASED ANALYSIS FOR ASSESSING LANDSLIDE AND DROUGHT HAZARD IN THE CORRIDOR OF MT. MERAPI AND MT. MERBABU NATIONAL PARK, INDONESIA

Directory of Open Access Journals (Sweden)

Hero Marhaento

2016-04-01

Full Text Available A corridor is an area located between two or more protected areas that are important to support the sustainability of the protected areas. This study is aimed at assessing landslide and drought hazard in the corridor area between Mt. Merapi National Park (MMNP and Mt. Merbabu National Park (MMbNP as a part of the corridor management strategy. The corridor area of MMNP and MMbNP comprises four sub-districts in Central Java Province, namely, Sawangan, Selo, Ampel, and Cepogo. A spatial analysis of ArcGIS 10.1 software was used to assess landslide hazard map and the Thorntwaite-Matter Water Balance approach was used to assess drought hazard map. The results have shown that three villages in Cepogo Sub-district and all villages in Selo Sub-district are highly prone to landslide hazard. Furthermore, two villages in Cepogo Sub-district and four villages in Selo Sub-district are prone to drought hazard. This study suggests that these villages should initiate a program called conservation village model based on disaster mitigation for mitigating future landslide and drought disasters.

Hazardous Chemicals

Centers for Disease Control (CDC) Podcasts

Chemicals are a part of our daily lives, providing many products and modern conveniences. With more than three decades of experience, The Centers for Disease Control and Prevention (CDC) has been in the forefront of efforts to protect and assess people's exposure to environmental and hazardous chemicals. This report provides information about hazardous chemicals and useful tips on how to protect you and your family from harmful exposure.

Medical University of South Carolina Environmental Hazards Assessment Program. Volume 5: Annual report, July 1, 1993--June 30, 1994 deliverables

Energy Technology Data Exchange (ETDEWEB)

1994-09-01

The Medical University of South Carolina`s vision is to become the premier national resource for medical information and for environmental/health risk assessment. A key component to the success of the many missions of the Environmental Hazards Assessment Program (EHAP) is timely access to large volumes of data. This study documents the results of the needs assessment effort conducted to determine the information access and processing requirement of EHAP. The following topics are addressed in this report: environmental medicine and risk communication: curriculum and a professional support network-Department of Family Medicine; environmental hazards assessment and education program in pharmacy graduate education in risk assessment; and graduate education risk assessment.

The KULTURisk Regional Risk Assessment methodology for water-related natural hazards - Part 1: Physical-environmental assessment

Science.gov (United States)

Ronco, P.; Gallina, V.; Torresan, S.; Zabeo, A.; Semenzin, E.; Critto, A.; Marcomini, A.

2014-07-01

In recent years, the frequency of catastrophes induced by natural hazard has increased and flood events in particular have been recognized as one of the most threatening water-related disasters. Severe floods have occurred in Europe over the last decade causing loss of life, displacement of people and heavy economic losses. Flood disasters are growing as a consequence of many factors, both climatic and non-climatic. Indeed, the current increase of water-related disasters can be mainly attributed to the increase of exposure (increase elements potentially at risk in floodplains area) and vulnerability (i.e. economic, social, geographic, cultural, and physical/environmental characteristics of the exposure). Besides these factors, the strong effect of climate change is projected to radically modify the usual pattern of the hydrological cycle by intensifying the frequency and severity of flood events both at local, regional and global scale. Within this context, it becomes urgent and dramatically relevant the need of promoting and developing effective and pro-active strategies, tools and actions which allow to assess and (possibly) to reduce the flood risks that threats different relevant receptors. Several methodologies to assess the risk posed by water-related natural hazards have been proposed so far, but very few of them can be adopted to implement the last European Flood Directive (FD). The present study is intended to introduce and present a state-of-the-art Regional Risk Assessment (RRA) methodology to evaluate the benefits of risk prevention in terms of reduced environmental risks due to floods. The methodology, developed within the recently phased out FP7-KULTURisk Project (Knowledge-based approach to develop a cULTUre of Risk prevention - KR) is flexible and can be adapted to different case studies (i.e. large rivers, alpine/mountain catchments, urban areas and coastal areas) and spatial scales (i.e. from the large river to the urban scale). The FD compliant

78 FR 44625 - Proposed Information Collection (Open Burn Pit Registry Airborne Hazard Self-Assessment...

Science.gov (United States)

2013-07-24

... DEPARTMENT OF VETERANS AFFAIRS Proposed Information Collection (Open Burn Pit Registry Airborne... to ``OMB Control No. 2900--NEW, Open Burn Pit Registry Airborne Hazard Self-Assessment Questionnaire... health effects of service members' exposure to toxic airborne chemicals and fumes caused by open burn...

TSUNAMI HAZARD ASSESSMENT IN THE NORTHERN AEGEAN SEA

Directory of Open Access Journals (Sweden)

Barbara Theilen-Willige

2008-01-01

Full Text Available Emergency planning for the assessment of tsunami hazard inundation and of secondary effects of erosion and landslides, requires mapping that can help identify coastal areas that are potentially vulnerable. The present study reviews tsunami susceptibility mapping for coastal areas of Turkey and Greece in the Aegean Sea. Potential tsunami vulnerable locations were identified from LANDSAT ETM imageries, Shuttle Radar Topography Mission (SRTM, 2000 data and QuickBird imageries and from a GIS integrated spatial database. LANDSAT ETM and Digital Elevation Model (DEM data derived by the SRTM-Mission were investigated to help detect traces of past flooding events. LANDSAT ETM imageries, merged with digitally processed and enhanced SRTM data, clearly indicate the areas that may be prone to flooding if catastrophic tsunami events or storm surges occur.

Assessing inundation hazards to nuclear powerplant sites using geologically extended histories of riverine floods, tsunamis, and storm surges

Science.gov (United States)

O'Connor, Jim; Atwater, Brian F.; Cohn, Timothy A.; Cronin, Thomas M.; Keith, Mackenzie K.; Smith, Christopher G.; Mason, Jr., Robert R.

2014-01-01

Most nuclear powerplants in the United States are near rivers, large lakes, or oceans. As evident from the Fukushima Daiichi, Japan, disaster of 2011, these water bodies pose inundation threats. Geologic records can extend knowledge of rare hazards from flooding, storm surges, and tsunamis. This knowledge can aid in assessing the safety of critical structures such as dams and energy plants, for which even remotely possible hazards are pertinent. Quantitative analysis of inundation from geologic records perhaps is most developed for and applied to riverine flood hazards, but because of recent natural disasters, geologic investigations also are now used widely for understanding tsunami hazards and coastal storm surges.

Mercury Hazard Assessment for Piscivorous Wildlife in Glacier National Park

KAUST Repository

Stafford, Craig P.

2016-12-14

We examined the mercury hazard posed to selected piscivorous wildlife in Glacier National Park (GNP), Montana. Logging Lake was our focal site where we estimated the dietary mercury concentrations of wildlife (common loon [Gavia immer], American mink [Neovison vison], river otter [Lontra canadensis], and belted kingfisher [Megaceryle alcyon]) by assuming that fishes were consumed in proportion to their relative abundances. To evaluate if Logging Lake provided a suitable baseline for our study, we made geographic comparisons of fish mercury levels and investigated the distribution and abundance of high mercury fishes within GNP. We complimented our assessment by examining selenium:mercury molar ratios in fishes from Logging Lake and Saint Mary Lake. Our results suggest fish consumption does not imperil wildlife from Logging Lake based on published thresholds for adverse mercury effects, but some hazard may exist particularly if there is strong feeding selectivity for the most contaminated species, northern pikeminnow (Ptychocheilus oregonensis). The geographic comparisons of fish mercury levels, together with the distribution and abundance of high mercury fishes within GNP, suggest that Logging Lake provided a relatively protective baseline among our study lakes. Risk may be further reduced by the molar excess of selenium relative to mercury, particularly in the smaller fishes typically consumed by GNP wildlife. Our findings contrast with studies from northeastern US and southeastern Canada where greater mercury hazard to wildlife exists. An emergent finding from our research is that waterborne concentrations of methylmercury may provide limited insight into regional differences in fish mercury levels.

Mercury Hazard Assessment for Piscivorous Wildlife in Glacier National Park

KAUST Repository

Stafford, Craig P.; Downs, Christopher C.; Langner, Heiko W.

2016-01-01

We examined the mercury hazard posed to selected piscivorous wildlife in Glacier National Park (GNP), Montana. Logging Lake was our focal site where we estimated the dietary mercury concentrations of wildlife (common loon [Gavia immer], American mink [Neovison vison], river otter [Lontra canadensis], and belted kingfisher [Megaceryle alcyon]) by assuming that fishes were consumed in proportion to their relative abundances. To evaluate if Logging Lake provided a suitable baseline for our study, we made geographic comparisons of fish mercury levels and investigated the distribution and abundance of high mercury fishes within GNP. We complimented our assessment by examining selenium:mercury molar ratios in fishes from Logging Lake and Saint Mary Lake. Our results suggest fish consumption does not imperil wildlife from Logging Lake based on published thresholds for adverse mercury effects, but some hazard may exist particularly if there is strong feeding selectivity for the most contaminated species, northern pikeminnow (Ptychocheilus oregonensis). The geographic comparisons of fish mercury levels, together with the distribution and abundance of high mercury fishes within GNP, suggest that Logging Lake provided a relatively protective baseline among our study lakes. Risk may be further reduced by the molar excess of selenium relative to mercury, particularly in the smaller fishes typically consumed by GNP wildlife. Our findings contrast with studies from northeastern US and southeastern Canada where greater mercury hazard to wildlife exists. An emergent finding from our research is that waterborne concentrations of methylmercury may provide limited insight into regional differences in fish mercury levels.

Volcanic Hazards in Site Evaluation for Nuclear Installations

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-10-15

This publication provides comprehensive and updated guidance for site evaluation in relation to volcanic hazards. It includes recommendations on assessing the volcanic hazards at a nuclear installation site, in order to identify and characterize, in a comprehensive manner, all potentially hazardous phenomena that may be associated with future volcanic events. It describes how some of these volcanic phenomena may affect the acceptability of the selected site, resulting in exclusion of a site or determining the corresponding design basis parameters for the installation. This Safety Guide is applicable to both existing and new sites, and a graded approach is recommended to cater for all types of nuclear installations. Contents: 1. Introduction; 2. Overview of volcanic hazard assessment; 3. General recommendations; 4. Necessary information and investigations (database); 5. Screening of volcanic hazards; 6. Site specific volcanic hazard assessment; 7. Nuclear installations other than nuclear power plants; 8. Monitoring and preparation for response; 9. Management system for volcanic hazard assessment; Annex I: Volcanic hazard scenarios; Annex II: Worldwide sources of information.

ASSESSMENT OF EARTHQUAKE HAZARDS ON WASTE LANDFILLS

DEFF Research Database (Denmark)

Zania, Varvara; Tsompanakis, Yiannis; Psarropoulos, Prodromos

Earthquake hazards may arise as a result of: (a) transient ground deformation, which is induced due to seismic wave propagation, and (b) permanent ground deformation, which is caused by abrupt fault dislocation. Since the adequate performance of waste landfills after an earthquake is of outmost...... importance, the current study examines the impact of both types of earthquake hazards by performing efficient finite-element analyses. These took also into account the potential slip displacement development along the geosynthetic interfaces of the composite base liner. At first, the development of permanent...

Transport of hazardous goods

International Nuclear Information System (INIS)

1989-01-01

The course 'Transport of hazardous goods' was held in Berlin in November 1988 in cooperation with the Bundesanstalt fuer Materialforschung und -pruefung. From all lecturs, two are recorded separately: 'Safety of tank trucks - requirements on the tank, development possibiities of active and passive safety' and 'Requirements on the transport of radioactive materials - possible derivations for other hazardous goods'. The other lectures deal with hazardous goods law, requirements on packinging, risk assessment, railroad transport, hazardous goods road network, insurance matters, EC regulations, and waste tourism. (HSCH) [de

RAPID-N: Assessing and mapping the risk of natural-hazard impact at industrial installations

Science.gov (United States)

Girgin, Serkan; Krausmann, Elisabeth

2015-04-01

Natural hazard-triggered technological accidents (so-called Natech accidents) at hazardous installations can have major consequences due to the potential for release of hazardous materials, fires and explosions. Effective Natech risk reduction requires the identification of areas where this risk is high. However, recent studies have shown that there are hardly any methodologies and tools that would allow authorities to identify these areas. To work towards closing this gap, the European Commission's Joint Research Centre has developed the rapid Natech risk assessment and mapping framework RAPID-N. The tool, which is implemented in an online web-based environment, is unique in that it contains all functionalities required for running a full Natech risk analysis simulation (natural hazards severity estimation, equipment damage probability and severity calculation, modeling of the consequences of loss of containment scenarios) and for visualizing its results. The output of RAPID-N are risk summary reports and interactive risk maps which can be used for decision making. Currently, the tool focuses on Natech risk due to earthquakes at industrial installations. However, it will be extended to also analyse and map Natech risk due to floods in the near future. RAPID-N is available at http://rapidn.jrc.ec.europa.eu. This presentation will discuss the results of case-study calculations performed for selected flammable and toxic substances to test the capabilities of RAPID-N both for single- and multi-site earthquake Natech risk assessment. For this purpose, an Istanbul earthquake scenario provided by the Turkish government was used. The results of the exercise show that RAPID-N is a valuable decision-support tool that assesses the Natech risk and maps the consequence end-point distances. These end-point distances are currently defined by 7 kPa overpressure for Vapour Cloud Explosions, 2nd degree burns for pool fire (which is equivalent to a heat radiation of 5 kW/m2 for 40s

The 3D Elevation Program—Landslide recognition, hazard assessment, and mitigation support

Science.gov (United States)

Lukas, Vicki; Carswell, Jr., William J.

2017-01-27

The U.S. Geological Survey (USGS) Landslide Hazards Program conducts landslide hazard assessments, pursues landslide investigations and forecasts, provides technical assistance to respond to landslide emergencies, and engages in outreach. All of these activities benefit from the availability of high-resolution, three-dimensional (3D) elevation information in the form of light detection and ranging (lidar) data and interferometric synthetic aperture radar (IfSAR) data. Research on landslide processes addresses critical questions of where and when landslides are likely to occur as well as their size, speed, and effects. This understanding informs the development of methods and tools for hazard assessment and situational awareness used to guide efforts to avoid or mitigate landslide impacts. Such research is essential for the USGS to provide improved information on landslide potential associated with severe storms, earthquakes, volcanic activity, coastal wave erosion, and wildfire burn areas.Decisionmakers in government and the private sector increasingly depend on information the USGS provides before, during, and following disasters so that communities can live, work, travel, and build safely. The USGS 3D Elevation Program (3DEP) provides the programmatic infrastructure to generate and supply lidar-derived superior terrain data to address landslide applications and a wide range of other urgent needs nationwide. By providing data to users, 3DEP reduces users’ costs and risks and allows them to concentrate on their mission objectives. 3DEP includes (1) data acquisition partnerships that leverage funding, (2) contracts with experienced private mapping firms, (3) technical expertise, lidar data standards, and specifications, and (4) most important, public access to high-quality 3D elevation data.

The crysophere as a resource and hazard - Integrated framework for the assessment of future water resource vulnerability and glacial hazard risk assessment in the Kullu district, Himachal Pradesh, India.