Influence of different cooling rates on the microstructure of the HAZ and welding CCT diagram of CLAM steel

International Nuclear Information System (INIS)

Zheng Shuhui; Wu Qingsheng; Huang Qunying; Liu Shaojun; Han Yangyang

2011-01-01

The evolution of microstructure in the weld HAZ (Heat Affected Zone) under welding thermal cycle was simulated by Gleeble-1500. The microstructures and properties of HAZ at different cooling rates were investigated by optical microscopy (OM), scanning electron microscopy (SEM) and microhardness test. The results showed that when the cooling rates ranged from 3600 K/min to 60 K/min, fully martensitic transformations were achieved, and the cooling rates had little influence on the microstructure and microhardness of martensite. The maximum cooling rate to form ferrite was 60 K/min. When the cooling rates ranged from 60 K/min to 1 K/min, the microhardness of the HAZ began to decrease due to the presence of ferrite, and the lath sizes grew up to 0.13-0.15 μm. The critical cooling rate to gain fully ferrite was found to be slower than 1 K/min. The welding CCT diagram of CLAM steel was constructed and it showed that there were ferrite and martensite transformation regions only. The diagram made it possible to predict the microstructures and properties of HAZ and became an important tool to evaluate weldability of CLAM steel.

Corrosion Cyclic Voltammetry of Two Types of Heat-Affected Zones (HAZs) of API-X100 Steel in Bicarbonate Solutions

Science.gov (United States)

Eliyan, Faysal Fayez; Alfantazi, Akram

2014-12-01

This paper examined the electrochemical corrosion behavior and corrosion products of two types of heat-affected HAZs made from API-X100 steel. Cyclic voltammetry, with different scan rates and potential ranges at 10 cycles, was applied to analyze the interdependent corrosion reactions of cathodic reduction, anodic dissolution, passivation, and transpassivation. The HAZ cooled at 60 K/s, from a peak temperature of 1470 K (1197 °C) that was held for 15 seconds, exhibited better passivation and lower cathodic activity than the HAZ cooled at 10 K/s. Increasing bicarbonate concentration, from 0.05 and 0.2 to 0.6 M, increases the anodic activity and cathodic reduction, but accordingly protects the active surfaces and enhances passivation.

Prediction of temperature and HAZ in thermal-based processes with Gaussian heat source by a hybrid GA-ANN model

Science.gov (United States)

Fazli Shahri, Hamid Reza; Mahdavinejad, Ramezanali

2018-02-01

Thermal-based processes with Gaussian heat source often produce excessive temperature which can impose thermally-affected layers in specimens. Therefore, the temperature distribution and Heat Affected Zone (HAZ) of materials are two critical factors which are influenced by different process parameters. Measurement of the HAZ thickness and temperature distribution within the processes are not only difficult but also expensive. This research aims at finding a valuable knowledge on these factors by prediction of the process through a novel combinatory model. In this study, an integrated Artificial Neural Network (ANN) and genetic algorithm (GA) was used to predict the HAZ and temperature distribution of the specimens. To end this, a series of full factorial design of experiments were conducted by applying a Gaussian heat flux on Ti-6Al-4 V at first, then the temperature of the specimen was measured by Infrared thermography. The HAZ width of each sample was investigated through measuring the microhardness. Secondly, the experimental data was used to create a GA-ANN model. The efficiency of GA in design and optimization of the architecture of ANN was investigated. The GA was used to determine the optimal number of neurons in hidden layer, learning rate and momentum coefficient of both output and hidden layers of ANN. Finally, the reliability of models was assessed according to the experimental results and statistical indicators. The results demonstrated that the combinatory model predicted the HAZ and temperature more effective than a trial-and-error ANN model.

Computer simulation of grain growth in HAZ

Science.gov (United States)

Gao, Jinhua

Two different models for Monte Carlo simulation of normal grain growth in metals and alloys were developed. Each simulation model was based on a different approach to couple the Monte Carlo simulation time to real time-temperature. These models demonstrated the applicability of Monte Carlo simulation to grain growth in materials processing. A grain boundary migration (GBM) model coupled the Monte Carlo simulation to a first principle grain boundary migration model. The simulation results, by applying this model to isothermal grain growth in zone-refined tin, showed good agreement with experimental results. An experimental data based (EDB) model coupled the Monte Carlo simulation with grain growth kinetics obtained from the experiment. The results of the application of the EDB model to the grain growth during continuous heating of a beta titanium alloy correlated well with experimental data. In order to acquire the grain growth kinetics from the experiment, a new mathematical method was developed and utilized to analyze the experimental data on isothermal grain growth. Grain growth in the HAZ of 0.2% Cu-Al alloy was successfully simulated using the EDB model combined with grain growth kinetics obtained from the experiment and measured thermal cycles from the welding process. The simulated grain size distribution in the HAZ was in good agreement with experimental results. The pinning effect of second phase particles on grain growth was also simulated in this work. The simulation results confirmed that by introducing the variable R, degree of contact between grain boundaries and second phase particles, the Zener pinning model can be modified as${D/ r} = {K/{Rf}}$where D is the pinned grain size, r the mean size of second phase particles, K a constant, f the area fraction (or the volume fraction in 3-D) of second phase.

Bursa’da Satışa Sunulan Çeşitli Hazır Köftelerin Hijyenik Kalitesinin Saptanması

Directory of Open Access Journals (Sweden)

G. Ece Soyutemiz

2015-02-01

Full Text Available Bu çalışma Bursa’da marketlerde ve kasap dükkanlarında hazır olarak satılan 5 farklı tip hazır köftenin (hamburger, İnegöl, kasap, Adana ve kaşarlı köfte hijyenik kalitesini saptamak, ayrıca farklı köfte gruplarının özelliklerini karşılaştırmak amacıyla yapıldı. Hazır köfteler bakteriyolojik olarak; toplam mezofil aerob bakteri, psikrofilik bakteri, koliform bakteri, E. coli, toplam stafilokok ve mikrokok, S. aureus, fekal streptokok, salmonella, maya ve küf sayısı bakımından incelendi. Sonuç olarak, hazır köftelerde, psikrofilik bakteriler, maya ve küf sayıları 107-108/g arasında yüksek değerler vermiş, köftelerin büyük bir kısmında patojen bakteriler 104-105/g değerleri arasında saptanmış, yüksek sayıda fekal streptokok tespit edilmiştir. Ancak hiçbir köfte grubunda Salmonellaya rastlanmamıştır. Hazır köftelerin yüksek bakteri içeriği ve yüksek pH değerleri göz önünde bulundurulduğunda köftelerin hijyenik açıdan risk oluşturabileceği görülmektedir. Bu durumda hazır köftelerin 4 oC’nin üzerine çıkmayan sıcaklıklarda saklanması ve en çok 2 gün içinde tüketilmesi uygundur.

Hazard and operability study (Haz Op) of the 2 MW IEA-R1 reactor startup procedures

International Nuclear Information System (INIS)

Sauer, Maria E.L.J.; Correa, Francisco; Sara Neto, Antonio J.; Costa, Carlos A.R. da; Santos, Cilas C. dos; Cardenas, Jose P.N.; Berretta, Jose R.; Neves Conti, Thadeu das

1997-01-01

This work presents the Hazard and Operability Study (Haz Op) applied to startup procedures of the 2 MW IEA-R1 research reactor, at IPEN/CNEN-S P. The Haz Op was developed by reviewing the procedures of the installation startup, in order to identify hazards and/or operational problems caused by deviations in the execution of these routines. This paper summarizes this study. describing some potential problems of relevant importance to safety as well as preventives and/or correctives measures to avoid their occurrence. Besides, an benefits evaluation and the technique limitations is made. (author). 5 refs., 1 tab

Microstructural, Micro-hardness and Sensitization Evaluation in HAZ of Type 316L Stainless Steel Joint with Narrow Gap Welds

Energy Technology Data Exchange (ETDEWEB)

Islam, Faisal Shafiqul; Jang, Changheui [KAIST, Daejeon (Korea, Republic of); Kang, Shi Chull [Korea Institute of Nuclear Safety, Daejeon (Korea, Republic of)

2015-10-15

From Micro-hardness measurement HAZ zone was found approximately 1-1.5 mm in NGW and DL-EPR test confirmed that 316L NGW HAZ was not susceptible to sensitization as DOS <1% according to sensitization criteria based on reference. In nuclear power plants 316L stainless steels are commonly used material for their metallurgical stability, high corrosion resistance, and good creep and ductility properties at elevated temperatures. Welding zone considered as the weakest and failure initiation source of the components. For safety and economy of nuclear power plants accurate and dependable structural integrity assessment of main components like pressure vessels and piping are need as it joined by different welding process. In similar and dissimilar metal weld it has been observed that weld microstructure cause the variation of mechanical properties through the thickness direction. In the Heat Affected Zone (HAZ) relative to the fusion line face a unique thermal experience during welding.

Microstructural characterization of the HAZ of the AISI 439 with different heat input

International Nuclear Information System (INIS)

Silva, Lorena de Azevedo; Lima, Luciana Iglesias Lourenco; Campos, Wagner Reis da Costa

2007-01-01

Ferritic stainless steels have certain useful corrosion properties, such as resistance to chloride, corrosion in oxidizing aqueous media, oxidation at high temperatures, etc. It is suitable for the aqueous chloride environments, heat transfer applications, condenser tubing for fresh water power plants, industrial buildings, and recently, the ferritic stainless steels have also received attention owing to its superior performance under irradiation. Sometimes in these applications the use of welding processes is necessary. The object of the present work was to research the relationship between microstructure and microhardness in the heat affect zone (HAZ) of the AISI 439, for two different heat input. The base metal shows a random distribution of the precipitates. The HAZ size, grain size, and the amount of precipitates had increased to the bigger heat input weld. The precipitation occurred in bigger amount in the sample with greater heat input, had increased the microhardness. It was observed that the grain size is related with heat input, and that the microhardness is more strong related with other feature, as carbides and nitrites precipitation. (author)

Experimental modeling of weld thermal cycle of the heat affected zone (HAZ

Directory of Open Access Journals (Sweden)

J. Kulhánek

2016-10-01

Full Text Available Contribution deals with experimental modeling of quick thermal cycles of metal specimens. In the introduction of contribution will be presented measured graphs of thermal cycle of heat affected zone (HAZ of weld. Next will be presented experimental simulation of measured thermal cycle on the standard specimens, useable for material testing. This approach makes possible to create material structures of heat affected zone of weld, big enough for standard material testing.

An investigation of the influence of strength mis-matching and HAZ width on the fracture behaviour of welds with cracks in the WM/HAZ interface

Energy Technology Data Exchange (ETDEWEB)

Rodrigues, D.M.; Menezes, L.F.; Loureiro, A. [Dept of Mechanical Eng., FCTUC, Coimbra (Portugal)

2004-07-01

In this paper a numerical study concerning the influence of the mis-match in mechanical properties and of the heat affected zone width on the crack driving force of welds with cracks in the weld metal / heat affected zone interface is described. This work was performed through the numerical simulation of three-point bending tests, using finite element meshes of weld samples with various HAZ widths and two different crack length sizes. The numerical calculation of the J integral and of the stress fields ahead the notch tip was used to evaluate the fracture strength variation in the welds. (orig.)

Analysis of the IEA-R1 reactor start-up procedures - an application of the HazOp method

International Nuclear Information System (INIS)

Sauer, Maria Eugenia Lago Jacques

2000-01-01

An analysis of technological catastrophic events that took place in this century shows that human failure and vulnerability of risk management programs are the main causes for the occurrence of accidents. As an example, plants and complex systems where the interface man-machine is close, the frequency of failures tends to be higher. Thus, a comprehensive knowledge of how a specific process can be potentially hazardous is a sine qua non condition to the operators training, as well as to define and implement more efficient plans for loss prevention and risk management. A study of the IEA-R1 research reactor start-up procedures was carried out, based upon the methodology Hazard and Operability Study (HazOp). The analytical and qualitative multidisciplinary HazOp approach provided means to a comprehensive review of the reactor start-up procedures, contributing to improve the understanding of the potential hazards associated to deviations on performing this routine. The present work includes a historical summary and a detailed description of the HazOp technique, as well as case studies in the process industries and the use of expert systems in the application of the method. An analysis of 53 activities of the IEA-R1 reactor start-up procedures was made, resulting in 25 recommendations of changes covering aspects of the project, operation and safety of the reactor. Eleven recommendations have been implemented. (author)

Simulated HAZ continuous cooling transformation diagram of a bogie steel of high-speed railway

Science.gov (United States)

Liu, Yue; Chen, Hui; Liu, Yan; Hang, Zongqiu

2017-07-01

Simulated HAZ continuous cooling transformation (SH-CCT) diagram presents the start and end points of phase transformation and the relationships of the microstructures of HAZ, temperature and cooling rates. It is often used to assess the weldability of materials. In this paper, a weathering steel Q345C which is widely used in the bogies manufacturing was studied. The cooling times from 800∘C to 500∘C (t8/5) were from 3 s to 6000 s, aiming to study the microstructures under different cooling rates. Different methods such as color metallography were used to obtain the metallography images. The results show that ferrite nucleates preferentially at the prior austenite grain boundaries and grows along the grain boundaries with a lath-like distribution when t8/5 is 300 s. Austenite transforms into ferrite, pearlite and bainite with decreasing t8/5. Pearlite disappears completely when t8/5 = 150 s. Martensite gradually appears when t8/5 decreases to 30 s. The hardness increases with decreasing t8/5. The SH-CCT diagram indicates that the welding input and t8/5 should be taken into consideration when welding. This work provides the relationships of welding parameters and microstructures.

Simulación del haz de electrones en un TEM como flujo de partículas cargadas

Directory of Open Access Journals (Sweden)

Alberto Hernández-Valle

2015-03-01

Full Text Available Se simuló el comportamiento de un haz de electrones en un Microscopio Electrónico de Transmisión (TEM en función del voltaje de aceleración, la corriente de excitación de las lentes y la permeabilidad relativa de las piezas polares, por medio del software COMSOL Multiphysics versión 4.2a. Los resultados mostraron una baja velocidad vertical en los electrones dispersos, los cuales fueron filtrados por los diafragmas. Además, los gráficos expusieron que la densidad del flujo magnético aumentó con el incremento en la permeabilidad magnética de las piezas polares. Además, un aumento en la densidad del flujo magnético incrementó el ángulo de los electrones divergentes y redujo su velocidad vertical. Finalmente, las observaciones demostraron que el número de electrones que entran en el sistema no afecta el comportamiento general del haz ni la magnitud de la densidad del flujo magnético.

JST Thesaurus Headwords and Synonyms: 溶接HAZ [MeCab user dictionary for science technology term[Archive

Lifescience Database Archive (English)

Full Text Available MeCab user dictionary for science technology term 溶接HAZ 名詞 一般 * * * * 溶接熱影響部 ヨウセツネツ...エイキョウブ ヨーセツネツエイキョーブ Thesaurus2015 200906097687943880 C GA07 MULTI_WORD 溶接 H A Z

Quantitative consideration for the tempering effect during multi-pass thermal cycle in HAZ of low-alloy steel

International Nuclear Information System (INIS)

Yu, Lina; Nakabayashi, Yuma; Saida, Kazuyoshi; Mochizuki, Masahito; Nishimoto, Kazutoshi; Kameyama, Masashi; Hirano, Shinro; Chigusa, Naoki

2011-01-01

A new Thermal Cycle Tempering Parameter (TCTP) to deal with the tempering effect during multi-pass thermal cycles has been proposed by extending Larson-Miller parameter (LMP). Experimental result revealed that the hardness in synthetic HAZ of the low alloy steel subjected to multi tempering thermal cycles has a good linear relationship with TCTP. By using this relationship, the hardness of the low-alloy steel reheated with tempering thermal cycles can be predicted when the original hardness is known. (author)

Enhancing international earth science competence in natural hazards through 'geoNatHaz

Science.gov (United States)

Giardino, Marco; Clague, John J.

2010-05-01

"geoNatHaz" is a Transatlantic Exchange Partnership project (TEP 2009-2012) within the framework of the EU-Canada programme for co-operation in higher education, training, and youth. The project is structured to improve knowledge and skills required to assess and manage natural hazards in mountain regions. It provides student exchanges between European and Canadian universities in order to enhance international competence in natural hazard research. The university consortium is led by Simon Fraser University (Canada) and Università degli studi di Torino (Italy). Partner universities include the University of British Columbia, Queen's University, Università di Bologna, Université de Savoie, and the University of Athens. Université de Lausanne (Switzerland) supports the geoNatHaz advisory board through its bilateral agreements with Canadian partner universities. The geoNatHaz project promotes cross-cultural understanding and internationalization of university natural hazard curricula through common lectures, laboratory exercises, and field activities. Forty graduate students from the seven Canadian and European partner universities will benefit from the project between 2009 and 2012. Some students enrolled in graduate-level earth science and geologic engineering programs spend up to five months at the partner universities, taking courses and participating in research teams under the direction of project scientists. Other students engage in short-term (four-week) exchanges involving training in classic natural hazard case-studies in mountain regions of Canada and Europe. Joint courses are delivered in English, but complementary cultural activities are offered in the languages of the host countries. Supporting organizations offer internships and technical and scientific support. Students benefit from work-study programs with industry partners. Supporting organizations include government departments and agencies (Geological Survey of Canada; CNR-IRPI National

Utilization of accident databases and fuzzy sets to estimate frequency of HazMat transport accidents

International Nuclear Information System (INIS)

Qiao Yuanhua; Keren, Nir; Mannan, M. Sam

2009-01-01

Risk assessment and management of transportation of hazardous materials (HazMat) require the estimation of accident frequency. This paper presents a methodology to estimate hazardous materials transportation accident frequency by utilizing publicly available databases and expert knowledge. The estimation process addresses route-dependent and route-independent variables. Negative binomial regression is applied to an analysis of the Department of Public Safety (DPS) accident database to derive basic accident frequency as a function of route-dependent variables, while the effects of route-independent variables are modeled by fuzzy logic. The integrated methodology provides the basis for an overall transportation risk analysis, which can be used later to develop a decision support system.

Modeling HAZ hardness and weld features with BPN technology

International Nuclear Information System (INIS)

Morinishi, S.; Bibby, M.J.; Chan, B.

2000-01-01

A BPN (back propagation network) system for predicting HAZ (heat-affected zone) hardnesses and GMAW (gas metal arc) weld features (size and shape) is described in this presentation. Among other things, issues of network structure, training and testing data selection, software efficiency and user interface are discussed. The system is evaluated by comparing network output with experimentally measured test data in the first instance, and with regression methods available for this purpose, thereafter. The potential of the web for exchanging weld process data and for accessing models generated with this system is addressed. In this regard the software has been made available on the Cambridge University 'steel' and 'neural' websites. In addition Java coded software has recently been generated to provide web flexibility and accessibility. Over and above this, the possibility of offering an on-line 'server' training service, arranged to capture user data (user identification, measured welding parameters and features) and trained models for the use of the entire welding community is described. While the possibility of such an exchange is attractive, there are several difficulties in designing such a system. Server software design, computing resources, data base and communications considerations are some of the issues that must be addressed with regard to a server centered training and database system before it becomes reality. (author)

Problem Davranışların Azaltılmasında Olumlu Davranışsal Destek Planı Hazırlama

Directory of Open Access Journals (Sweden)

Dilek Erbaş

2002-07-01

Full Text Available Günümüzde problem davranışlara, normal gelişim gösteren ve özürlü çocuklarda oldukça sık rastlanılmaktadır. Problem davranışlar öğrencilerin yaşamlarını farklı şekillerde olumsuz olarak etkilemekledir. Problem davranış gösteren bireyler bit davranışları nedeniyle, eğitim ve öğretim olanaklarından yeterince yararlanamamaktadır. Ayrıca, bu bireyler akranları ve toplumdaki diğer bireyler tarafından dışlanabildikleri için bazı sosyal becerileri geliştirememekle ya da sınırlı düzeyde geliştirebilmekledirler. Dolayısıyla, öğretmenler, öğrencilerin yaşamlarını olumsuz etkileyen bu davranışları azaltmak için, olumlu davranışsal destek planı hazırlamalıdır. Hazırlanan bu planlar, uygulamalı davranış analiz ilkelerine dayalı olmalıdır. Ayrıca, hazırlanan planın Öğrenciye ve uygulayacak bireylerin değer yargılarına uygun olması gereklidir. Olumlu davranışsal destek planının sahip olması gereken diğer önemli bir özelliği ise, hazırlanan planın. Öğrencinin yaşam kalitesini arttıracak şekilde desenlenınesi ve uygulanmasıdır. Kapsamlı bir plan hazırlamak için, planı ayrıntılı şekilde yazmak, tutarlı ve sistemli olarak uygulamak ve planın etkililiğini değerlendirmek ve gerektiğinde düzenlemeleri yapmak için veri toplamak gibi basamakları gerçekleştirmek gereklidir. Problem behaviors are frequently seen among the children with normal development as well as children with disabilities- Problem behaviors affect the students' lives in different negative ways. Individuals exhibiting problem behaviors cannot make the most out of their educational opportunities due to their behaviors. What's more, these individuals may run the risk of being incompetent or restricted İn some social skills because of being excluded by their peers. Thus, teachers should prepare behavior-changing plans based on positive behavior support to mitigate the problem behaviors

Control of the development of residual stresses and heat affected zone (HAZ) microstructure during welding of low alloy steels and influence on stress relieve cracking

Energy Technology Data Exchange (ETDEWEB)

Storesund, J.; Rui Wu; Sandstroem, R.; von Walden, E. [Swedish Inst. for Metals Research, Stockholm (Sweden)

1990-12-31

Creep resistant 1 Cr 0.5 Mo steels are frequently used as steam pipes at operating temperature of 450 degree C to 500 degrees C. Welded joints have been post weld heat treated (PWHT). The results show: - In fully refined microstructures close to the fusion boundary of the weldments a reduction of the grain size by a factor of 3-4 was measured. The impact transition temperature was up to 27 degree C lower for test series notched in the refined HAZ (Heat Affected Zone) than in the coarse grained HAZ of the as welded condition. The overlay heat treatments were not observed to significantly influence the hardness and the room temperature tensile properties of the weldments. - The influence of refinement on impact transition temperature (ITT) and upper shelf energy was beneficial. In the coarse grained HAZ, for which the ITT was significantly higher than for weld metal and base metal, the refinement resulted in a 30 degrees C lower value of the ITT. The influence of PWHT on impact properties was also studied. The PWHT raised the upper shelf energy greatly. The effect on the ITT was smaller than that of refinement. - For cross welds in the as-welded (AW) condition refinement improved the creep properties. After PWHT the creep ductility was significantly increased at the same as a considerable reduction of life was observed. At lower stresses the effects of refinement and especially PWHT were less pronounced. Beneficial influence of refinement in inhibiting the formation of creep cavitation was apparent regardless stress level in both AW and PWHT conditions. (K.A.E).

Fotodisociación de un haz molecular de cetena a 193 nm. : procesos de uno y dos fotones

OpenAIRE

Ruiz del Castillo, Javier

1995-01-01

En el presente trabajo se ha estudiado experimentalmente la fotodisociación de un haz molecular de cetena (ch2co) con un laser de arf (longitud de onda de 193 nm). Como fragmentos resultantes producto de la fotodisociación se han observado el metileno ch2 (b1b1) que se manifiesta en su emisión de fluorescencia ch2 (b1b1 - a1a1) en la región espectral 500-760 nm, y el radical metilideno ch, en sus estados electrónicos a2 , b2 , y c2 +, en sus transiciones electrónicas al estado fundamental x2 ...

Hazır Gıda Ürünleri Satın Alma Davranışını Etkileyen Pazarlama Faktörlerinin İncelenmesi: Iğdır İlinde Bir Araştırma

Directory of Open Access Journals (Sweden)

Faruk BAŞTÜRK

2014-04-01

Full Text Available Araştırmanın amacı, Iğdır’daki süper marketlerden hazır gıda satın alan tüketicilerin hazır gıda satın alımını etkileyen pazarlama karması faktörlerini analiz etmektir. Tüketicilerin hazır gıda satın alma davranışlarının yanı sıra bu satın almadan bekledikleri yararları işlevsel ve hazcı bazda incelemek araştırmanın diğer amacıdır. Araştırmanın yöntemi, tanımlayıcı nitelikte ve ampirik şekilde tasarlanmıştır. Araştırmada veri toplama yöntemi ankettir ve kolayda örnekleme yoluyla 408 gözleme ulaşılmıştır. Bulgulara göre, tüketicilerin satın alma davranışını etkileyen pazarlama karması faktörlerinin önem sırasının Ürün-Dağıtım, Fiyat, Ürün, Tutundurma-Dağıtım olduğu; tüketicilerin hazır gıda ürünlerini satın alırken İşlevselci davranışı Hazcılıktan daha fazla sergilediği ve İşlevselcilerin Hazcılara göre 4 pazarlama karması faktörüne daha fazla önem verdiği ortaya çıkmıştır. Sonuçta hazır gıda perakendecilerine özgü öneriler getirilmiştir.

The Evolution of Cast Microstructures on the HAZ Liquation Cracking of Mar-M004 Weld

Directory of Open Access Journals (Sweden)

Yi-Hsin Cheng

2018-01-01

Full Text Available The causes of liquation cracking in the heat-affected zone (HAZ of a cast Mar-M004 superalloy weld were investigated. X-ray diffraction (XRD, electron probe microanalyzer (EPMA, and electron backscatter diffraction (EBSD were applied to identify the final microconstituents at the solidification boundaries of the cast alloy. Fine borides and lamellar eutectics were present in front of some γ-γ′ colonies, which were expected to be liquefied prematurely during welding. The metal carbide (MC enriched in Nb, Hf; M3B2 and M5B3 borides enriched in Cr and Mo; and lamellar Ni-Hf intermetallics were mainly responsible for the induced liquation cracking of the Mar-M004 weld, especially the MC carbides. Scanning electron microscope (SEM fractographs showed that the fracture features of those liquation cracks were associated with the interdendritic constituents in the cast superalloy.

Determinación de la absorción de haz láser en ensayos de refusión en régimen continuo

Directory of Open Access Journals (Sweden)

Lima, M.

1998-04-01

Full Text Available Not available

[pt] Este trabalho estuda a absorção do feixe laser sobre a superfície de um ferro fundido branco por meio de ensaios calorimétricos. Um láser de CO₂, trabalhando no modo contínuo, foi utilizado para produzir um traço refundido sobre a superfície de um ferro fundido branco em intervalos de velocidade de varredura do feixe entre 0,01 e 1,00 cm/s. O registro da temperatura em função do tempo foi realizada por três termopares fixados à superfície inferior da amostra. Verificou-se que cerva de 13 % da radiação incidente sobre a superfície da amostra é absorvida em forma de calor, para um feixe com 0,65 mm de diâmetro, idependentemente da velocidade de varredura do feixe. No caso do feixe com diâmetro de 1,11 mm, a absorção cai para cerca de 11 %. [es] Se estudia la absorción del rayo láser por la superficie de una fundición blanca utilizando ensayos calorimétricos. Se utilizó un láser tipo CO₂ trabajando en modo continuo. Se realizaron trazos refundidos continuos en la superficie de la fundición blanca con velocidad de desplazamiento del haz láser comprendida entre 0,01 y 1,00 cm/s. Para el registro de la temperatura en función del tiempo se utilizaron tres termopares colocados sobre la superficie de la muestra. Se comprobó que, aproximadamente, el 13 % de la radiación incidente sobre la superficie de la muestra es absorbida en forma de calor, para un haz láser de 0,65 mm de diámetro, independientemente de la velocidad de paso del mismo. En el caso del haz láser de 1,11 mm de diámetro, la absorción disminuye a valores próximos al 11 %.

DomeHaz, a Global Hazards Database: Understanding Cyclic Dome-forming Eruptions, Contributions to Hazard Assessments, and Potential for Future Use and Integration with Existing Cyberinfrastructure

Science.gov (United States)

Ogburn, S. E.; Calder, E.; Loughlin, S.

2013-12-01

Dome-forming eruptions can extend for significant periods of time and can be dangerous; nearly all dome-forming eruptions have been associated with some level of explosive activity. Large Plinian explosions with a VEI ≥ 4 sometimes occur in association with dome-forming eruptions. Many of the most significant volcanic events of recent history are in this category. The 1902-1905 eruption of Mt. Pelée, Martinique; the 1980-1986 eruption of Mount St. Helens, USA; and the 1991 eruption of Mt. Pinatubo, Philippines all demonstrate the destructive power of VEI ≥ 4 dome-forming eruptions. Global historical analysis is a powerful tool for decision-making as well as for scientific discovery. In the absence of monitoring data or a knowledge of a volcano's eruptive history, global analysis can provide a method of understanding what might be expected based on similar eruptions. This study investigates the relationship between large explosive eruptions and lava dome growth and develops DomeHaz, a global database of dome-forming eruptions from 1000 AD to present. It is currently hosted on VHub (https://vhub.org/groups/domedatabase/), a community cyberinfrastructure for sharing data, collaborating, and modeling. DomeHaz contains information about 367 dome-forming episodes, including duration of dome growth, duration of pauses in extrusion, extrusion rates, and the timing and magnitude of associated explosions. Data sources include the The Smithsonian Institution Global Volcanism Program (GVP), Bulletin of the Global Volcanism Network, and all relevant published review papers, research papers, and reports. This database builds upon previous work (e.g Newhall and Melson, 1983) in light of newly available data for lava dome eruptions. There have been 46 new dome-forming eruptions, 13 eruptions that continued past 1982, 151 new dome-growth episodes, and 8 VEI ≥ 4 events since Newhall and Melson's work in 1983. Analysis using DomeHaz provides useful information regarding the

Endüstriyel İşletmelerde Franchising Model Önerisi: Hazır Beton Sektöründe Bir Uygulama

Directory of Open Access Journals (Sweden)

İpek Kazançoğlu

2016-12-01

Full Text Available Endüstriyel pazarda faaliyet gösteren firmaların daha hızlı büyüyerek, yeni pazarlara açılmasında franchising sistemi bir yeni bir satış, dağıtım kanalı olarak değerlendirilmektedir. Bu araştırmada amaç,  hazır beton sektöründe faaliyet gösteren bir firmanın franchising sistemini bir iş modeli olarak benimseme kararında dikkat etmesi gereken unsurları ve karşılaşılan zorlukları incelemektedir. Örnek olay çalışması olarak ele alınan çalışmada,  BATIBETON A.Ş. firmasının yedi yöneticiyle BATIBETON markasının franchising uygulamalarına ilişkin görüşlerini öğrenmek amacıyla derinlemesine görüşmeler yapılmıştır. Bu görüşmeler sonucunda, franchising sisteminin hazır beton sektöründe bir model önerisi olarak uygulanıp/uygulanmayacağı değerlendirilmiştir. Yapılan görüşmelerden elde edilen bulguların diğer endüstriyel işletmeler içinde geliştirilebilecek bir franchising iş modeli kararında etkili olabilecek faktörlerin anlaşılması yönünden uygulamaya katkı sağlayacağı düşünülmektedir.

High toughness in the intercritically reheated coarse-grained (ICRCG) heat-affected zone (HAZ) of low carbon microalloyed steel

Energy Technology Data Exchange (ETDEWEB)

Hu, Jun, E-mail: hujunral@163.com [The State Key Laboratory of Rolling and Automation, Northeastern University, Shenyang 110819 (China); Du, Lin-Xiu [The State Key Laboratory of Rolling and Automation, Northeastern University, Shenyang 110819 (China); Wang, Jian-Jun [Institute of Materials Research, School of Material and Metallurgy, Northeastern University, Shenyang 110819 (China); Xie, Hui; Gao, Cai-Ru [The State Key Laboratory of Rolling and Automation, Northeastern University, Shenyang 110819 (China); Misra, R.D.K. [Laboratory for Excellence in Advanced Steel Research, Center for Structural and Functional Materials, University of Louisiana at Lafayette, Lafayette, LA 70504-4130 (United States)

2014-01-10

Motivated by the small lattice mismatch between ferrite and vanadium nitride (VN), we describe here the welding thermal cycle simulation that provides high toughness in the ICRCG HAZ of low carbon V–N steel. This unique behavior is attributed to the formation of ultra-fine grained ferrite along prior austenite grain boundaries generated by the first pass welding thermal cycle with high misorientation boundaries, where V(C, N) precipitates provide potential nucleation sites for ferrite, leading to extraordinary refinement of martensite/austenite (M/A) constituent. Nitrogen stimulates the precipitation behavior of V(C, N). The nucleation of high density of V(C, N) precipitates consumes carbon-content in the austenite, leading to decrease in the carbon-content in the M/A constituent, with consequent decrease in hardness. The increase in toughness is explained in terms of Griffith's crack propagation theory.

High toughness in the intercritically reheated coarse-grained (ICRCG) heat-affected zone (HAZ) of low carbon microalloyed steel

International Nuclear Information System (INIS)

Hu, Jun; Du, Lin-Xiu; Wang, Jian-Jun; Xie, Hui; Gao, Cai-Ru; Misra, R.D.K.

2014-01-01

Motivated by the small lattice mismatch between ferrite and vanadium nitride (VN), we describe here the welding thermal cycle simulation that provides high toughness in the ICRCG HAZ of low carbon V–N steel. This unique behavior is attributed to the formation of ultra-fine grained ferrite along prior austenite grain boundaries generated by the first pass welding thermal cycle with high misorientation boundaries, where V(C, N) precipitates provide potential nucleation sites for ferrite, leading to extraordinary refinement of martensite/austenite (M/A) constituent. Nitrogen stimulates the precipitation behavior of V(C, N). The nucleation of high density of V(C, N) precipitates consumes carbon-content in the austenite, leading to decrease in the carbon-content in the M/A constituent, with consequent decrease in hardness. The increase in toughness is explained in terms of Griffith's crack propagation theory

Evaluación de Lesiones Periapicales en Pacientes Derivados a Cirugía Periapical Mediante Tomografía Computarizada de Haz Cónico

OpenAIRE

Hernández Vigueras, Scarlette; Donoso Zúñiga, Manuel; Sanhueza Tobar, Claudio; Linco Olave, Jared; Riquelme Carrasco, Sebastián

2017-01-01

El uso de la tomografía computarizada de haz cónico (CBCT) en endodoncia ha ido en aumento, justificando su uso en casos más complejos, como cirugías periapicales. El objetivo fue evaluar las características imagenológicas encontradas en un grupo de pacientes derivados a cirugía periapical, mediante el uso de CBCT. Se realizó un estudio observacional descriptivo, en un grupo de pacientes, derivados a cirugía periapical, a los cuales se realizó un examen de CBCT, evaluación clínica y radiograf...

Improvement technique of sensitized HAZ by GTAW cladding applied to a BWR power plant

International Nuclear Information System (INIS)

Tujimura, Hiroshi; Tamai, Yasumasa; Furukawa, Hideyasu; Kurosawa, Kouichi; Chiba, Isao; Nomura, Keiichi.

1995-01-01

A SCC(Stress Corrosion Cracking)-resistant technique, in which the sleeve installed by expansion is melted by GTAW process without filler metal with outside water cooling, was developed. The technique was applied to ICM (In-Core Monitor) housings of a BWR power plant in 1993. The ICM housings of which materials are type 304 Stainless Steels are sensitized with high tensile residual stresses by welding to the RPV (Reactor Pressure Vessel). As the result, ICM housings have potential of SCC initiation. Therefore, the improvement technique resistant to SCC was needed. The technique can improve chemical composition of the housing inside and residual stresses of the housing outside at the same time. Sensitization of the housing inner surface area is eliminated by replacing low-carbon with proper-ferrite microstructure clad. High tensile residual stresses of housing outside surface area is improved into compressive side. Compressive stresses of outside surface are induced by thermal stresses which are caused by inside cladding with outside water cooling. The clad is required to be low-carbon metal with proper ferrite and not to have the new sensitized HAZ (Heat Affected Zone) on the surface by cladding. The effect of the technique was qualified by SCC test, chemical composition check, ferrite content measurement and residual stresses measurement etc. All equipment for remote application were developed and qualified, too. The technique was successfully applied to a BWR plant after sufficient training

El uso de fotocélulas de haz simple y doble para medir la velocidad en carreras®. The use of single- and dual-beam photocells to measure the sprint time®.

Directory of Open Access Journals (Sweden)

Juan García-López

2012-10-01

Full Text Available ResuemnEl objetivo del estudio fue analizar la influencia de la tecnología de las fotocélulas en el registro de tiempo y su fiabilidad durante de carreras de velocidad de corta distancia. Participaron 25 estudiantes (20.5±0.5 años; 1.78±0.02 m; 77.5±1.8 kg que fueron evaluados en 3 días (2 de familiarización y 1 de test. Se registraron aleatoriamente 3 carreras de aceleración y 3 velocidad lanzada, cronometradas simultáneamente a los 5, 10 y 15 m por dos sistemas de fotocélulas DSD Laser System®: haz simple y doble haz. El tipo de fotocélulas utilizadas influyó en el tiempo de carrera (F=11.92 y p 0.80 a los 10 y 5 m, respectivamente. En la carrera lanzada ambos sistemas midieron prácticamente igual (diferencias de ~0.005 s, obteniendo registros fiables a los 15 y 10 m, respectivamente. En conclusión, en carreras de aceleración la distancia mínima a registrar con haz simple debe ser de 10 m, y de 5 m con haz doble, mientras que en carreras lanzadas deberían utilizarse unas distancias mínimas de 15 y 10 m, respectivamente. Futuros estudios deberían analizar la distancia óptima a la primera fotocélula en las carreras de aceleración, para aumentar la fiabilidad de la medición y facilitar la comparación entre registros de diferentes estudios.AbstractThe purpose was to analyze the influence of the timing gates’ technology on both running time performance and its reliability during short sprint distances. Twenty-five physical students participated (20.5±0.5 yr; 1.78±0.02 m; 77.5±1.8 kg, whose were evaluated during 3 separate days (2 familiarization sessions and 1 testing session. Three standing-start and 3 flying-start runs were randomized and simultaneously registered at 5, 10 and 15 m by two timing gates DSD Laser System®: single- and dual-beam. The type of timing gates affected the performance (F=11.92 y p0.80 at the distances of 10 and 5 m, respectively. During the flying-start runs, both systems obtained a very

Eğitsel Değerlendirme ve Bireyselleştirilmiş Eğitim Programı Hazırlama Süreci

Directory of Open Access Journals (Sweden)

Tevhide Kargın

2007-01-01

Full Text Available Eğitsel değerlendirme süreci, engelli ya da risk durumunda olduğundan şüphe edilen çocukları ilk belirleme aşamasından başlayarak, gönderme öncesi süreç, gönderme, ayrıntılı değerlendirme, özel eğitim hizmetleri için uygunluğuna karar verme, yerleştirme, bireyselleştirilmiş eğitim programı hazırlama, uygulama ve değerlendirme-izleme aşamalarından oluşan bir süreci tanımlamak amacıyla kullanılan bir terimdir. Makalede bu aşamalar tanımlanmış ve her bir aşamada dikkat edilmesi gereken önemli noktalar vurgulanmaya çalışılmıştır. Assessment procedures consist of screening, pre-referral, referral, evaluation, eligibility determination, placement, developing, implementation and monitoring of the individualized education programs (IEP, in this article all these steps were defined and the important issues in each step were emphasized.

HAZ microstructure in joints made of X13CrMoCoVNbNB9-2-1 (PB2 steel welded with and without post-weld heat treatment

Directory of Open Access Journals (Sweden)

M. Łomozik

2016-07-01

Full Text Available The article presents the results of research butt welded joints made of X13CrMoCoVNbNB9-2-1 steel. The joints were welded with post-weld heat treatment PWHT and without PWHT, using the temper bead technique TBT. After welding the joint welded with PWHT underwent stress-relief annealing at 770 °C for 3 hours. The scope of structural tests included the microstructural examination of the coarse-grained heat affected zone (HAZ areas of the joints, the comparison of the morphology of these areas and the determination of carbide precipitate types of the coarse grain heat affected zone (CGHAZ of the joints welded with and without PWHT.

The Use of Haz-Flote to Efficiently Remove Mercury from Contaminated Materials

Energy Technology Data Exchange (ETDEWEB)

Terry Brown

2009-03-03

There are thousands of known contaminated sites in the United Stated, including Superfund sites (1500 to 2100 sites), RCRA corrective action sites (1500 to 3500 sites), underground storage tanks (295,000 sites), U.S. Department of Defense sites (7300 sites), U.S. Department of Energy sites (4,000 sites), mining refuse piles, and numerous other hazardous metals and organic contamination sites. Only a small percentage of these sites has been cleaned up. The development of innovative technologies to handle the various clean-up problems on a national and international scale is commonplace. Many innovative technologies have been developed that can be used to effectively remediate contaminated materials. Unfortunately, many of these technologies are only effective for materials coarser than approximately 200 mesh. In addition, these technologies usually require considerable investment in equipment, and the clean-up costs of soil material are relatively high - in excess of $100 to $500 per yd{sup 3}. These costs result from the elaborate nature of the processes, the costs for power, and the chemical cost. The fine materials are disposed of or treated at considerable costs. As a result, the costs often associated with amelioration of contaminated sites are high. Western Research institute is in the process of developing an innovative soil washing technology that addresses the removal of contaminants from the fine size-fraction materials located at many of the contaminated sites. This technology has numerous advantages over the other ex-situ soil washing techniques. It requires a low capital investment, low operating costs and results in high levels of re-emplacement of the cleaned material on site. The process has the capability to clean the fine fraction (<200 mesh) of the soil resulting in a replacement of 95+% of the material back on-side, reducing the costs of disposal. The Haz-Flote{trademark} technology would expand the application of soil washing technology to heavy

Creep Rupture of the Simulated HAZ of T92 Steel Compared to that of a T91 Steel

Directory of Open Access Journals (Sweden)

Yu-Quan Peng

2017-02-01

Full Text Available The increased thermal efficiency of fossil power plants calls for the development of advanced creep-resistant alloy steels like T92. In this study, microstructures found in the heat-affected zone (HAZ of a T92 steel weld were simulated to evaluate their creep-rupture-life at elevated temperatures. An infrared heating system was used to heat the samples to 860 °C (around AC1, 900 °C (slightly below AC3, and 940 °C (moderately above AC3 for one minute, before cooling to room temperature. The simulated specimens were then subjected to a conventional post-weld heat treatment (PWHT at 750 °C for two hours, where both the 900 °C and 940 °C simulated specimens had fine grain sizes. In the as-treated condition, the 900 °C simulated specimen consisted of fine lath martensite, ferrite subgrains, and undissolved carbides, while residual carbides and fresh martensite were found in the 940 °C simulated specimen. The results of short-term creep tests indicated that the creep resistance of the 900 °C and 940 °C simulated specimens was poorer than that of the 860 °C simulated specimens and the base metal. Moreover, simulated T92 steel samples had higher creep strength than the T91 counterpart specimens.

Creep Rupture of the Simulated HAZ of T92 Steel Compared to that of a T91 Steel.

Science.gov (United States)

Peng, Yu-Quan; Chen, Tai-Cheng; Chung, Tien-Jung; Jeng, Sheng-Long; Huang, Rong-Tan; Tsay, Leu-Wen

2017-02-08

The increased thermal efficiency of fossil power plants calls for the development of advanced creep-resistant alloy steels like T92. In this study, microstructures found in the heat-affected zone (HAZ) of a T92 steel weld were simulated to evaluate their creep-rupture-life at elevated temperatures. An infrared heating system was used to heat the samples to 860 °C (around A C1 ), 900 °C (slightly below A C3 ), and 940 °C (moderately above A C3 ) for one minute, before cooling to room temperature. The simulated specimens were then subjected to a conventional post-weld heat treatment (PWHT) at 750 °C for two hours, where both the 900 °C and 940 °C simulated specimens had fine grain sizes. In the as-treated condition, the 900 °C simulated specimen consisted of fine lath martensite, ferrite subgrains, and undissolved carbides, while residual carbides and fresh martensite were found in the 940 °C simulated specimen. The results of short-term creep tests indicated that the creep resistance of the 900 °C and 940 °C simulated specimens was poorer than that of the 860 °C simulated specimens and the base metal. Moreover, simulated T92 steel samples had higher creep strength than the T91 counterpart specimens.

Zihin Engelliler Sınıf Öğretmenlerinin Bireyselleştirilmiş Eğitim Programı (BEP Hazırlamaya İlişkin Görüşleri

Directory of Open Access Journals (Sweden)

Hasan Avcıoğlu

2011-01-01

Full Text Available Bu çalışmada, Bireyselleştirilmiş Eğitim Programı (BEPnın öğrenilmesi, hazırlanması ve uygulamasına ilişkin zihin engelliler sınıf öğretmenlerinin görüşlerinin belirlenmesi amaçlanmıştır. Araştırmada, nitel araştırma yönteminden yararlanılmıştır. Amaçlı örnekleme yöntemine göre belirlenmiş olan katılımcılar toplam 12 zihin engelliler sınıf öğretmeninden oluşturulmuştur. Verilerin toplanmasında yarı-yapılandırılmış görüşme tekniği ve toplam 17 sorudan oluşan bir görüşme formu kullanılmıştır. Araştırma verilerinin analizinde, betimsel analiz yaklaşımından yararlanılmıştır. Yapılan analizler sonucunda öğretmenlerin BEP hazırlarken öğrencilerin aileleriyle oldukça az görüştükleri ailelerin ve öğrencilerin görüşlerinden yeterince yararlanmadıkları anlaşılmaktadır. BEP’te yer alması gereken kısımlar ve BEP’te belirlenen hedef davranışlara ulaşılıp ulaşılmadığının değerlendirilmesi konusunda yeterince bilgi sahibi olmadıkları da elde edilen bulgular arasındadır. Zihin engelliler sınıf öğretmenlerinin BEP’i öğrenme yaşantıların da farklı olduğu, BEP’i hazırlama ve uygulamada da sorunlar yaşadıkları araştırmanın bulguları arasındadır. In this study determination of mental handicapped class teachers’ thoughts about learning, preparing and applying IEP was aimed. Participants who were determined according to aimed sampling method include mental handicapped class teachers. During collecting data, semi-structured interview technique and an interview form that consists of 17 questions were used. In the analysis of the data descriptive analysis concept was used. During determining questions, themes about teachers’ 1- Learning IEP experience, 2- Applying IEP experience, and 3- Thoughts about IEP were determined and findings were introduced according to them. It is understood from teachers’ expressions that

Early childhood linear growth faltering in low-income and middle-income countries as a whole-population condition: analysis of 179 Demographic and Health Surveys from 64 countries (1993-2015).

Science.gov (United States)

Roth, Daniel E; Krishna, Aditi; Leung, Michael; Shi, Joy; Bassani, Diego G; Barros, Aluisio J D

2017-12-01

The causes of early childhood linear growth faltering (known as stunting) in low-income and middle-income countries remain inadequately understood. We aimed to determine if the progressive postnatal decline in mean height-for-age Z score (HAZ) in low-income and middle-income countries is driven by relatively slow growth of certain high-risk children versus faltering of the entire population. Distributions of HAZ (based on WHO growth standards) were analysed in 3-month age intervals from 0 to 36 months of age in 179 Demographic and Health Surveys from 64 low-income and middle-income countries (1993-2015). Mean, standard deviation (SD), fifth percentiles, and 95th percentiles of the HAZ distribution were estimated for each age interval in each survey. Associations between mean HAZ and SD, fifth percentile, and 95th percentile were estimated using multilevel linear models. Stratified analyses were performed in consideration of potential modifiers (world region, national income, sample size, year, or mean HAZ in the 0-3 month age band). We also used Monte Carlo simulations to model the effects of subgroup versus whole-population faltering on the HAZ distribution. Declines in mean HAZ from birth to 3 years of age were accompanied by declines in both the fifth and 95th percentiles, leading to nearly symmetrical narrowing of the HAZ distributions. Thus, children with relatively low HAZ were not more likely to have faltered than taller same-age peers. Inferences were unchanged in surveys regardless of world region, national income, sample size, year, or mean HAZ in the 0-3 month age band. Simulations showed that the narrowing of the HAZ distribution as mean HAZ declined could not be explained by faltering limited to a growth-restricted subgroup of children. In low-income and middle-income countries, declines in mean HAZ with age are due to a downward shift in the entire HAZ distribution, revealing that children across the HAZ spectrum experience slower growth compared to

Proyecto Haz[Otea

Directory of Open Access Journals (Sweden)

Ricardo Alvira Baeza

2016-07-01

  For some time now, it has become increasingly common hearing about the great potential trans-forming urban rooftop spaces poses for increasing cities’ sustainability, in a speech usually encour-aging their adaptation into green roofs or use for locating renewable energy generators. However, it is currently extremely difficult assessing to what extent these statements are correct: • Available information and assessments of these rooftops’ types describe technical issues and/or focus on specific aspects of their impact on reality [thermal insulation, rain water re-tention ...] being hardly relatable to the impact a general transformation of an urban area’s rooftops would imply for the area’s overall state. • The impact of some technological solution/design may be different in different urban are-as. • Rooftops may host several uses, yet we have found no document providing an extensive comparison of the impact of each of them. To assist in this debate, in this text we estimate the expected impact of the hypothetical transfor-mation of all available rooftops in an existing urban area: Palos de Moguer neighborhood in Madrid. In order to do so, we use Meta[S] model proposed by the author as PhD Thesis project, which as-sesses 64 dimensions of urban reality. The assessment allows us to highlight three key issues: • Not all possible rooftops transformations produce the same benefit for cities/urban areas, and in urban consolidated environments rooftop transformations that allow people’s use may pose higher collective benefit. • Rooftops transformations benefit maximization requires individual analysis of each urban area, relating its particular needs with available rooftop surface characteristics. • The number of different rooftops possible uses and their ease of implementation can be greatly increased if some previsions are incorporated in Urban Planning/Building Codes These last two issues allow us to state the interest of both updating national Building & Design Codes and that municipalities regulate the conditions and use of rooftop spaces. In the Conclusions we list some issues we believe should be incorporated by different rooftops’ regulations.

Haz-Map Glossary

Science.gov (United States)

... than 5000 ppm." [ ERG 2008 ] TLV Threshold limit value. (ACGIH) Tolerance "The amount of pesticide that may safely remain ... than 5000 ppm." [ ERG 2008 ] TLV Threshold limit value. (ACGIH) Tolerance "The amount of pesticide that may safely remain ...

Hardening Embrittlement and Non-Hardening Embrittlement of Welding-Heat-Affected Zones in a Cr-Mo Low Alloy Steel

Directory of Open Access Journals (Sweden)

Yu Zhao

2018-06-01

Full Text Available The embrittlement of heat affected zones (HAZs resulting from the welding of a P-doped 2.25Cr-1Mo steel was studied by the analysis of the fracture appearance transition temperatures (FATTs of the HAZs simulated under a heat input of 45 kJ/cm with different peak temperatures. The FATTs of the HAZs both with and without tempering increased with the rise of the peak temperature. However, the FATTs were apparently lower for the tempered HAZs. For the as-welded (untempered HAZs, the FATTs were mainly affected by residual stress, martensite/austenite (M/A islands, and bainite morphology. The observed embrittlement is a hardening embrittlement. On the other hand, the FATTs of the tempered HAZs were mainly affected by phosphorus grain boundary segregation, thereby causing a non-hardening embrittlement. The results demonstrate that the hardening embrittlement of the as-welded HAZs was more severe than the non-hardening embrittlement of the tempered HAZs. Consequently, a post-weld heat treatment should be carried out if possible so as to eliminate the hardening embrittlement.

Phase transformation and impact properties in the experimentally simulated weld heat-affected zone of a reduced activation ferritic/martensitic steel

Energy Technology Data Exchange (ETDEWEB)

Moon, Joonoh, E-mail: mjo99@kims.re.kr [Ferrous Alloy Department, Advanced Metallic Materials Division, Korea Institute of Materials Science, 797 Changwondaero, Seongsangu, Changwon, Gyeongnam 642-831 (Korea, Republic of); Lee, Chang-Hoon; Lee, Tae-Ho [Ferrous Alloy Department, Advanced Metallic Materials Division, Korea Institute of Materials Science, 797 Changwondaero, Seongsangu, Changwon, Gyeongnam 642-831 (Korea, Republic of); Jang, Min-Ho [Ferrous Alloy Department, Advanced Metallic Materials Division, Korea Institute of Materials Science, 797 Changwondaero, Seongsangu, Changwon, Gyeongnam 642-831 (Korea, Republic of); Division of Materials Science and Engineering, Hanyang University, Seongdong-ku, Seoul 133-791 (Korea, Republic of); Park, Min-Gu [Ferrous Alloy Department, Advanced Metallic Materials Division, Korea Institute of Materials Science, 797 Changwondaero, Seongsangu, Changwon, Gyeongnam 642-831 (Korea, Republic of); Department of Material Science and Engineering, Pusan National University, 30 Jangjeon-Dong, Geumjeong-gu, Pusan 609-735 (Korea, Republic of); Han, Heung Nam [Department of Materials Science and Engineering, Seoul National University, 1 Gwanak-ro, Gwanak-gu, Seoul 151-742 (Korea, Republic of)

2014-12-15

In this work, the phase transformation and impact properties in the weld heat-affected zone (HAZ) of a reduced activation ferritic/martensitic (RAFM) steel are investigated. The HAZs were experimentally simulated using a Gleeble simulator. The base steel consisted of tempered martensite through normalizing at 1000 °C and tempering at 750 °C, while the HAZs consisted of martensite, δ-ferrite and a small volume of autotempered martensite. The impact properties using a Charpy V-notch impact test revealed that the HAZs showed poor impact properties due to the formation of martensite and δ-ferrite as compared with the base steel. In addition, the impact properties of the HAZs further deteriorated with an increase in the δ-ferrite fraction caused by increasing the peak temperature. The impact properties of the HAZs could be improved through the formation of tempered martensite after post weld heat treatment (PWHT), but they remained lower than that of the base steel because the δ-ferrite remained in the tempered HAZs.

Peyniraltı Suyu Tozundan Hazırlanan Sentetik Besi Ortamında Lactobacillus bulgaricus Suşlarının Oluşturduğu Laktik Asit Miktarı Üzerine bir Araştırma

OpenAIRE

Beyatlı, Yavuz; Tulumoğlu, Şener

1991-01-01

Peyniraltı suyu tozundan altı farklı sentetik besi ortamı hazırlanmıştır. Bu besi ortamlarında 12 adet L. bulgaricus suşunun oluşturduğu laktik asit miktarları tespit edilmiştir. Katkılı besi ortamlarında oluşan laktik asit miktarları, katkısız besi ortamları ile kıyaslandığında daha fazla bulunmuştur. 12 adet L. bulgaricus suşu arasında en fazla laktik asit üretenlerin L. bulgaricus B1, L. bulgaricus B4 ve L. bulgaricus B11 suşları olduğu görülmüştür.  

SCC growth behavior of stainless steel weld heat-affected zone in hydrogenated high temperature water

International Nuclear Information System (INIS)

Yamada, Takuyo; Terachi, Takumi; Miyamoto, Tomoki; Arioka, Koji

2010-01-01

It is known that the SCC growth rate of stainless steels in high-temperature water is accelerated by cold-work (CW). The weld heat-affected-zone (HAZ) of stainless steels is also deformed by weld shrinkage. However, only little have been reported on the SCC growth of weld HAZ of SUS316 and SUS304 in hydrogenated high-temperature water. Thus, in this present study, SCC growth experiments were performed using weld HAZ of stainless steels, especially to obtain data on the dependence of SCC growth on (1) temperature and (2) hardness in hydrogenated water at temperatures from 250degC to 340degC. And then, the SCC growth behaviors were compared between weld HAZ and CW stainless steels. The following results have been obtained. Significant SCC growth were observed in weld HAZ (SUS316 and SUS304) in hydrogenated water at 320degC. The SCC growth rates of the HAZ are similar to that of 10% CW non-sensitized SUS316, in accordance with that the hardness of weld HAZ is also similar to that of 10% CW SUS316. Temperature dependency of SCC growth of weld HAZ (SUS316 and SUS304) is also similar to that of 10% CW non-sensitized SUS316. That is, no significant SCC were observed in the weld HAZ (SUS316 and SUS304) in hydrogenated water at 340degC. This suggests that SCC growth behaviors of weld HAZ and CW stainless steels are similar and correlated with the hardness or yield strength of the materials, at least in non-sensitized regions. And the similar temperature dependence between the HAZ and CW stainless steels suggests that the SCC growth behaviors are also attributed to the common mechanism. (author)

Heat-affected zone microstructure and mechanical properties evolution for laser remanufacturing 35CrMoA axle steel

Science.gov (United States)

Feng, Xiangyi; Dong, Shiyun; Yan, Shixing; Liu, Xiaoting; Xu, Binshi; Pan, Fusheng

2018-03-01

In this article, by using orthogonal test the technological test was conducted and the optimum processing of the remanufacturing35CrMoA axle were obtained. The evolution of microstructure and mechanical property of HAZ were investigated. The microstructure of HAZ was characterized by means of OM and SEM. Meanwhile hardness distribution in HAZ and tensile property of cladding-HAZ-substrate samples were measured. The microstructure of cladding and HAZ were observed. The microsturcture evoltion and the mechanism of harden in the HAZ was discussed and revealed. The results indicated that the remanufacturing part has excellent strength due to grain refining and dispersive distribution of nanoscale cementite. The remanufacturing part will have uniform microstructure and hardness matching with that of 35CrMoA axle by using stress-relieving annealing at 580°.

Microstructure, Composition, and Impact Toughness Across the Fusion Line of High-Strength Bainitic Steel Weldments

Science.gov (United States)

Lan, Liangyun; Kong, Xiangwei; Chang, Zhiyuan; Qiu, Chunlin; Zhao, Dewen

2017-09-01

This paper analyzed the evolution of microstructure, composition, and impact toughness across the fusion line of high-strength bainitic steel weldments with different heat inputs. The main purpose was to develop a convenient method to evaluate the HAZ toughness quickly. The compositions of HAZ were insensitive to higher contents of alloy elements ( e.g., Ni, Mo) in the weld metal because their diffusion distance is very short into the HAZ. The weld metal contained predominantly acicular ferrite at any a heat input, whereas the main microstructures in the HAZ changed from lath martensite/bainite to upper bainite with the increasing heat input. The evolution of HAZ toughness in relation to microstructural changes can be revealed clearly combined with the impact load curve and fracture morphology, although the results of impact tests do not show an obvious change with heat input because the position of Charpy V notch contains the weld metal, HAZ as well as a part of base metal. As a result, based on the bead-on-plate welding tests, the welding parameter affecting the HAZ toughness can be evaluated rapidly.

Primer implante de electrodo de estimulación selectiva del haz de His en Colombia: Reporte de dos casos First implantation of selective his bundle pacing in Colombia: Report of two cases

Directory of Open Access Journals (Sweden)

Jorge E Velásquez

2010-06-01

Full Text Available Se conoce que la estimulación en el ápex del ventrículo derecho produce disincronía ventricular y muchas veces los pacientes desarrollan miocardiopatía dilatada, lo que ha llevado a realizar una estimulación más fisiológica. Con el reciente desarrollo tecnológico de los electrodos para la estimulación selectiva del haz de His (fisiológica, se quiere mostrar la experiencia en el implante de este tipo de electrodos en los dos primeros casos del servicio de electrofisiología de la Clínica Medellín.Pacing in the right ventricular apex is known to produce ventricular dysynchrony and patients often develop dilated cardiomiopathy. For this reason, a more physiological stimulation has been performed. With the recent technological development of electrodes for selective stimulation of the His bundle, we want to show the experience of this type of implantation in the first two cases made in the electrophysiology laboratory in Medellin.

Prediction of laser cutting heat affected zone by extreme learning machine

Science.gov (United States)

Anicic, Obrad; Jović, Srđan; Skrijelj, Hivzo; Nedić, Bogdan

2017-01-01

Heat affected zone (HAZ) of the laser cutting process may be developed based on combination of different factors. In this investigation the HAZ forecasting, based on the different laser cutting parameters, was analyzed. The main goal was to predict the HAZ according to three inputs. The purpose of this research was to develop and apply the Extreme Learning Machine (ELM) to predict the HAZ. The ELM results were compared with genetic programming (GP) and artificial neural network (ANN). The reliability of the computational models were accessed based on simulation results and by using several statistical indicators. Based upon simulation results, it was demonstrated that ELM can be utilized effectively in applications of HAZ forecasting.

Body composition at birth and height at 2 years

DEFF Research Database (Denmark)

Admassu, Bitiya; Wells, Jonathan C; Girma, Tsinuel

2017-01-01

-free mass (FFM) were measured using air-displacement plethysmography within 48 h of birth. Linear regression models were applied to study the relationship between BC at birth and HAZ at 24 months (±3 months). RESULTS: A total of 268 children with height assessment at 2 years were included. Mean±s.d. HAZ...... at 2 years of age was -1.2±1.2, with 25.8% classified as stunted (HAZFFM at birth was positively associated with HAZ at 2 years, independent of length at birth. When adjusted for potential confounders, HAZ at 2 years was 0.73 higher for each additional kg FFM at birth (β=0.73, 95%CI (0.08, 1.......38). FM was not associated with HAZ at 2 years in any model. CONCLUSION: The FFM component of birth weight, independent of length, explains variability in HAZ at 2 years. Further studies are required to explore how changes in early infant BC are associated with linear growth.Pediatric Research accepted...

Correlation of microstructure and fracture toughness of advanced 9Cr/CrMoV dissimilarly welded joint

Energy Technology Data Exchange (ETDEWEB)

Guo, Qian [Shanghai Key Laboratory of Materials Laser Processing and Modification, School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China); Lu, Fenggui, E-mail: Lfg119@sjtu.edu.cn [Shanghai Key Laboratory of Materials Laser Processing and Modification, School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China); Liu, Xia [Shanghai Turbine Plant of Shanghai Electric Power Generation Equipment Co. Ltd., Shanghai 200240 (China); Yang, Renjie [Shanghai Turbine Works Company, Shanghai 200240 (China); Cui, Haichao [Shanghai Key Laboratory of Materials Laser Processing and Modification, School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China); Gao, Yulai, E-mail: ylgao@shu.edu.cn [State Key Laboratory of Advanced Special Steels, Shanghai University, Shanghai 200072 (China)

2015-06-25

In this paper, the fracture toughness and the related microstructure characteristics of dissimilarly welded joint manufactured by advanced 9Cr and CrMoV steels were systematically investigated. The dissimilarly welded joint was fabricated by narrow gap submerged arc welding (NG-SAW) applying multi-layer and multi-pass technique. Fracture toughness, as one of the most important property to assess the reliability of welded joint, was studied for different regions including CrMoV base metal (CrMoV-BM), heat affected zone (HAZ) of CrMoV side (CrMoV-HAZ), weld metal (WM), heat affected zone of 9Cr side (9Cr-HAZ) and 9Cr base metal (9Cr-BM). It was found that the fracture toughness of CrMoV-BM, CrMoV-HAZ and WM was better than that of 9Cr-HAZ and 9Cr-BM. In order to illustrate these results, the microstructure of the whole welded joint was observed by optical microscope (OM), scanning electron microscope (SEM) and transmission electron microscope (TEM) detailedly. It was found that the fine high-temperature tempered martensite and bainite in WM, CrMoV-BM and CrMoV-HAZ contribute to the higher fracture toughness, while lower fracture toughness for 9Cr-BM and HAZ was caused by coarse tempered lath-martensite. Furthermore, the fracture morphology showed that ductile fracture occurred in WM and CrMoV side, while brittle fracture appeared in BM and HAZ of 9Cr side.

S-11: Rio 2016 Paralimpik Oyunlarına Hazırlanan Türkiye Paralimpik Milli Takımı Ağız-Diş Sağlığı Profili

Directory of Open Access Journals (Sweden)

Osman Hamamcılar

2017-03-01

Full Text Available AMAÇ: Rio 2016 Paralimpik Oyunlarına hazırlanan Türk sporcularının ağız-diş sağlığı profilini göstermek ve koruyucu diş hekimliği hizmetlerini arttırmaya yönelik önlemler almaktır. MATERYAL-METOD: Çalışmamıza Rio 2016 Paralimpik Oyunlarına hazırlanan judo, atletizm ve erkek golball branşlarından oluşan görme engelli n=17 (% 24 sporcu; okçuluk, basketbol, yüzme, tenis, masa tenisi branşlarından oluşan bedensel engelli n=43 (% 60,5 sporcu ve işitme engelli tekvando branşından n=11 (% 15,5 sporcu katıldı. Sporcuların çürük (D, kayıp (M, restore diş (F indeksi (DMF-T ve toplumda periodontal tedavi gereksinim indeksi (CPITN değerlendirmeleri, Dünya Sağlık Örgütü (DSÖ kriterlerine göre yapıldı. BULGULAR: Sporcuların sahip oldukları çürük, kayıp ve restore diş sayısal değerleri ile yaş Paired-Samples T Testi istatiksel analiz yöntemi ile istatiksel olarak değerlendirildiğinde; D, M ve F sayısal değeri ile yaş arasında, istatiksel olarak anlamlılık görüldü (p<0.05. Cinsiyet ile diş hastalığı karşılaştırıldığında, D, M ve F sayısal değerleri her iki cinsiyette istatiksel olarak anlamlıydı (p<0.05; cinsiyet ve periodontal doku hastalığı arasındaki ilişkide her iki cinsiyette istatiksel olarak anlamlı bulundu (p<0,05. SONUÇ: Engelli sporcuların sahip oldukları diş ve dişeti hastalık oranları DSÖ 2020 hedef değerlerinin üzerindeydi. Buna rağmen sporcu grubunun diş kaybından daha çok dişin tedavisine yönelik eylemlerde bulunduğu görüldü. Koruyucu diş hekimliği hizmetini arttırmak için engelli sporculara yılda iki kez ağız-diş sağlığı kontrolü yapılmalı ve ağız-diş sağlığının sporcu sağlığı üzerine etkileri hakkında eğitimler düzenlenmelidir.

Austenite grain growth and microstructure control in simulated heat affected zones of microalloyed HSLA steel

Energy Technology Data Exchange (ETDEWEB)

Zhang, Lei [Department of Machine Tools and Factory Management, Technical University of Berlin, Pascalstraße 8 – 9, 10587, Berlin (Germany); Federal Institute for Materials Research and Testing, Unter den Eichen 87, 12205, Berlin (Germany); Kannengiesser, Thomas [Federal Institute for Materials Research and Testing, Unter den Eichen 87, 12205, Berlin (Germany); Institute of Materials and Joining Technology, Otto von Guericke University Magdeburg, Universitetsplatz 2, 39106, Magdeburg (Germany)

2014-09-08

The roles of microalloying niobium, titanium and vanadium for controlling austenite grain growth, microstructure evolution and hardness were investigated at different simulated heat affected zones (HAZ) for high strength low alloy (HSLA) S690QL steel. High resolution FEG-SEM has been used to characterize fine bainitic ferrite, martensite and nanosized second phases at simulated coarse and fine grain HAZs. It was found that for Ti bearing steel (Ti/N ratio is 2) austenite grain had the slowest growth rate due to the presence of most stable TiN. The fine cuboidal particles promoted intragranular acicular ferrite (IGF) formation. Nb bearing steel exhibited relatively weaker grain growth retardation compared with titanium bearing steels and a mixed microstructure of bainite and martensite was present for all simulated HAZs. IGF existed at coarse grain HAZ of Ti+V bearing steel but it was totally replaced by bainite at fine grain HAZs. Hardness result was closely related to the morphology of bainitic ferrite, intragranular ferrite and second phases within ferrite. The microstructure and hardness results of different simulated HAZs were in good agreement with welded experimental results.

The effect of particle size on the heat affected zone during laser cladding of Ni-Cr-Si-B alloy on C45 carbon steel

Science.gov (United States)

Tanigawa, Daichi; Abe, Nobuyuki; Tsukamoto, Masahiro; Hayashi, Yoshihiko; Yamazaki, Hiroyuki; Tatsumi, Yoshihiro; Yoneyama, Mikio

2018-02-01

Laser cladding is one of the most useful surface coating methods for improving the wear and corrosion resistance of material surfaces. Although the heat input associated with laser cladding is small, a heat affected zone (HAZ) is still generated within the substrate because this is a thermal process. In order to reduce the area of the HAZ, the heat input must therefore be reduced. In the present study, we examined the effects of the powdered raw material particle size on the heat input and the extent of the HAZ during powder bed laser cladding. Ni-Cr-Si-B alloy layers were produced on C45 carbon steel substrates in conjunction with alloy powders having average particle sizes of 30, 40 and 55 μm, while measuring the HAZ area by optical microscopy. The heat input required for layer formation was found to decrease as smaller particles were used, such that the HAZ area was also reduced.

Effect of preliminary thermal treatment of EhP-56 on resistivity to cold cracks formation in the joint heat affected zone

International Nuclear Information System (INIS)

Fedorov, V.G.; Shubin, V.I.; Belov, Yu.M.

1975-01-01

Data are given on the influence of the conditions of prior heat treatment on the resistance of steel EP56 to cold cracking in the joint heat affected zone /HAZ/. Other things being equal, the resistance of steel EP56 to cold cracking in the HAZ increases with reduction of hardness and increase of austenite content. Conditions for welding steel EP56, preventing cracking in the HAZ, have been determined

On post-weld heat treatment cracking in tig welded superalloy ATI 718Plus

Science.gov (United States)

Asala, G.; Ojo, O. A.

The susceptibility of heat affected zone (HAZ) to cracking in Tungsten Inert Gas (TIG) welded Allvac 718Plus superalloy during post-weld heat treatment (PWHT) was studied. Contrary to the previously reported case of low heat input electron beam welded Allvac 718Plus, where HAZ cracking occurred during PWHT, the TIG welded alloy is crack-free after PWHT, notwithstanding the presence of similar micro-constituents that caused cracking in the low input weld. Accordingly, the formation of brittle HAZ intergranular micro-constituents may not be a sufficient factor to determine cracking propensity, the extent of heat input during welding may be another major factor that influences HAZ cracking during PWHT of the aerospace superalloy Allvac 718Plus.

Effect of heat input on heat affected zone cracking in laser welded ATI Allvac 718Plus superalloy

International Nuclear Information System (INIS)

Idowu, O.A.; Ojo, O.A.; Chaturvedi, M.C.

2007-01-01

The heat affected zones (HAZs) of low and high heat input laser welds of a newly developed superalloy, ATI Allvac 718Plus, were studied. Low heat input welds suffered significant HAZ grain boundary liquation cracking, while no cracking was observed in spite of a more extensive HAZ intergranular liquation in the higher heat input welds. Combination of lower welding stresses generated during cooling, and relaxation of these stresses by thick intergranular liquid were suggested to be the factors that contributed to the absence of cracking in the high heat input welds. Further, healing of some of the HAZ cracks in lower heat input welds by fusion zone interdendritic liquid occurred through liquid backfilling

Corrosion Behavior of Metal Active Gas Welded Joints of a High-Strength Steel for Automotive Application

Science.gov (United States)

Garcia, Mainã Portella; Mantovani, Gerson Luiz; Vasant Kumar, R.; Antunes, Renato Altobelli

2017-10-01

In this work, the corrosion behavior of metal active gas-welded joints of a high-strength steel with tensile yield strength of 900 MPa was investigated. The welded joints were obtained using two different heat inputs. The corrosion behavior has been studied in a 3.5 wt.% NaCl aqueous solution using electrochemical impedance spectroscopy and potentiodynamic polarization tests. Optical microscopy images, scanning electron microscopy and transmission electron microscopy with energy-dispersive x-ray revealed different microstructural features in the heat-affected zone (HAZ) and the weld metal (WM). Before and after the corrosion process, the sample was evaluated by confocal laser scanning microscopy to measure the depth difference between HAZ and WM. The results showed that the heat input did not play an important role on corrosion behavior of HSLA steel. The anodic and cathodic areas of the welded joints could be associated with depth differences. The HAZ was found to be the anodic area, while the WM was cathodic with respect to the HAZ. The corrosion behavior was related to the amount and orientation nature of carbides in the HAZ. The microstructure of the HAZ consisted of martensite and bainite, whereas acicular ferrite was observed in the weld metal.

Softening Behavior of a New Al-Zn-Mg-Cu Alloy Due to TIG Welding

Science.gov (United States)

Zhang, Liang; Li, Xiaoyan; Nie, Zuoren; Huang, Hui; Sun, Jiantong

2016-05-01

A new Al-Zn-Mg-Cu alloy with T6 temper was welded by TIG welding, and the softening behavior of the joint was evaluated. Results show that the ultimate tensile strength of the joint is 436.2 ± 26.4 MPa which is about 64.5% of that of the base metal (BM). Fusion zone (FZ) is the weakest region even though its microhardness increases from 107.6 to 131.3 HV within 90 days after welding. Microhardness of the heat-affected zone (HAZ) adjacent to FZ increases from 125.2 to 162.3 HV within 90 days. However, a valley value of microhardness appears in the rest of the HAZ that increases from 112.1 to 128.1 HV within 90 days. The variation of grain size and precipitates is regarded as the main cause of softening in both FZ and HAZ. The grain size of FZ is about 33.9 μm, whereas 8.7 and 8.4 μm for HAZ and BM, respectively. A large number of η' phases distribute dispersively in BM, whereas precipitates in FZ identified as GPI zones are finer and fewer. Besides, precipitates in HAZ adjacent to FZ are also GPI zones. Precipitates in HAZ far away from FZ are coarser and fewer than those in BM and η phases begin to emerge.

Effect of post-weld heat treatment and neutron irradiation on a dissimilar-metal joint between F82H steel and 316L stainless steel

Energy Technology Data Exchange (ETDEWEB)

Fu, Haiying, E-mail: haigirl1983@gmail.com [SOKENDAI - The Graduated University for Advanced Studies, Toki (Japan); Nagasaka, Takuya [SOKENDAI - The Graduated University for Advanced Studies, Toki (Japan); National Institute for Fusion Science, Toki (Japan); Kometani, Nobuyuki [Nagoya University, Nagoya (Japan); Muroga, Takeo [SOKENDAI - The Graduated University for Advanced Studies, Toki (Japan); National Institute for Fusion Science, Toki (Japan); Guan, Wenhai; Nogami, Shuhei; Yabuuchi, Kiyohiro; Iwata, Takuya; Hasegawa, Akira [Tohoku University, Sendai (Japan); Yamazaki, Masanori [International Research Center for Nuclear Materials Science, Institute for Materials Research, Tohoku University (Japan); Kano, Sho; Satoh, Yuhki; Abe, Hiroaki [Institute for Materials Research, Tohoku University, Sendai (Japan); Tanigawa, Hiroyasu [Japan Atomic Energy Agency, Rokkasho (Japan)

2015-10-15

Highlights: • Significant hardening after neutron irradiation at 300 °C for 0.1 dpa was found in the fine-grain HAZ of F82H for the dissimilar-metal joint between F82H and 316L. • The possible hardening mechanism was explained from the viewpoint of carbon behavior. • However, the significant hardening did not degrade the impact property significantly. - Abstract: A dissimilar-metal joint between F82H steel and 316L stainless steel was fabricated by using electron beam welding (EBW). By microstructural analysis and hardness test, the heat-affected zone (HAZ) of F82H was classified into interlayer area, fine-grain area, and coarse-carbide area. Post-weld heat treatment (PWHT) was applied to control the hardness of HAZ. After PWHT at 680 °C for 1 h, neutron irradiation at 300 °C with a dose of 0.1 dpa was carried out for the joint in Belgian Reactor II (BR-II). Compared to the base metals (BMs) and weld metal (WM), significant irradiation hardening up to 450HV was found in the fine-grain HAZ of F82H. However, the impact property of F82H-HAZ specimens, which was machined with the root of the V-notch at HAZ of F82H, was not deteriorated obviously in spite of the significant irradiation hardening.

Microstructural Characterization of the Heat-Affected Zones in Grade 92 Steel Welds: Double-Pass and Multipass Welds

Science.gov (United States)

Xu, X.; West, G. D.; Siefert, J. A.; Parker, J. D.; Thomson, R. C.

2018-04-01

The microstructure in the heat-affected zone (HAZ) of multipass welds typical of those used in power plants and made from 9 wt pct chromium martensitic Grade 92 steel is complex. Therefore, there is a need for systematic microstructural investigations to define the different regions of the microstructure across the HAZ of Grade 92 steel welds manufactured using the traditional arc welding processes in order to understand possible failure mechanisms after long-term service. In this study, the microstructure in the HAZ of an as-fabricated two-pass bead-on-plate weld on a parent metal of Grade 92 steel has been systematically investigated and compared to a complex, multipass thick section weldment using an extensive range of electron and ion-microscopy-based techniques. A dilatometer has been used to apply controlled thermal cycles to simulate the microstructures in distinctly different regions in a multipass HAZ using sequential thermal cycles. A wide range of microstructural properties in the simulated materials were characterized and compared with the experimental observations from the weld HAZ. It has been found that the microstructure in the HAZ can be categorized by a combination of sequential thermal cycles experienced by the different zones within the complex weld metal, using the terminology developed for these regions based on a simpler, single-pass bead-on-plate weld, categorized as complete transformation, partial transformation, and overtempered.

A comparison of height and weight velocity as a part of the composite endpoint in pediatric HIV.

Science.gov (United States)

Benjamin, Daniel K; Miller, Wiliam C; Benjamin, Daniel K; Ryder, Robert W; Weber, David J; Walter, Emmanuel; McKinney, Ross E

2003-11-07

HIV adversely affects growth in children. Pediatric AIDS Clinical Trial Group (PACTG) protocols often use weight velocity [changes in weight z-score for age (WAZ)] as a part of the composite endpoint for phase II and III clinical trials. However, WAZ and height velocity (HAZ) have not been critically compared for their utility as part of the composite endpoint. HAZ and WAZ were compared to predict laboratory and clinical progression of HIV in a retrospective cohort study of HIV-infected children with data from PACTG Protocol 300. In both bivariable and multivariable analyses, changes in HAZ were more closely linked to subsequent progression than WAZ. Children with improved HAZ were somewhat less likely to exhibit virological failure [odds ratio (OR), 0.76; 95% confidence interval (CI) 0.51-1.14], than children with improved WAZ (OR, 1.45; 95% CI, 0.99,2.11). Children who had improved HAZ were less likely to exhibit immunological failure (OR, 0.7; 95% CI, 0.49-1.00), than children with improved WAZ (OR, 1.13; 95% CI, 0.82-1.57). Children who had improved HAZ were less likely to have other forms of clinical progression of HIV (OR, 0.55; 95% CI, 0.31-0.99), than children who had improved WAZ (OR, 1.0; 95% CI, 1.58-1.94). Increases in HAZ were associated with reduced risk of subsequent clinical progression and subsequent immune reconstitution and weakly associated with declines in HIV RNA. Changes in WAZ were not associated with laboratory outcomes relevant to pediatric HIV infection. Height velocity should be considered as a component of a composite clinical endpoint in future PACTG trials.

Corrosion behavior in high heat input welded heat-affected zone of Ni-free high-nitrogen Fe–18Cr–10Mn–N austenitic stainless steel

International Nuclear Information System (INIS)

Moon, Joonoh; Ha, Heon-Young; Lee, Tae-Ho

2013-01-01

The pitting corrosion and interphase corrosion behaviors in high heat input welded heat-affected zone (HAZ) of a metastable high-nitrogen Fe–18Cr–10Mn–N austenitic stainless steel were explored through electrochemical tests. The HAZs were simulated using Gleeble simulator with high heat input welding condition of 300 kJ/cm and the peak temperature of the HAZs was changed from 1200 °C to 1350 °C, aiming to examine the effect of δ-ferrite formation on corrosion behavior. The electrochemical test results show that both pitting corrosion resistance and interphase corrosion resistance were seriously deteriorated by δ-ferrite formation in the HAZ and their aspects were different with increasing δ-ferrite fraction. The pitting corrosion resistance was decreased by the formation of Cr-depleted zone along δ-ferrite/austenite (γ) interphase resulting from δ-ferrite formation; however it didn't depend on δ-ferrite fraction. The interphase corrosion resistance depends on the total amount of Cr-depleted zone as well as ferrite area and thus continuously decreased with increasing δ-ferrite fraction. The different effects of δ-ferrite fraction on pitting corrosion and interphase corrosion were carefully discussed in terms of alloying elements partitioning in the HAZ based on thermodynamic consideration. - Highlights: • Corrosion behavior in the weld HAZ of high-nitrogen austenitic alloy was studied. • Cr 2 N particle was not precipitated in high heat input welded HAZ of tested alloy. • Pitting corrosion and interphase corrosion show a different behavior. • Pitting corrosion resistance was affected by whether or not δ-ferrite forms. • Interphase corrosion resistance was affected by the total amount of δ-ferrite

Growth Patterns of HIV Infected Indian Children in Response to ART: A Clinic Based Cohort Study.

Science.gov (United States)

Parchure, Ritu S; Kulkarni, Vinay V; Darak, Trupti S; Mhaskar, Rahul; Miladinovic, Branko; Emmanuel, Patricia J

2015-06-01

To describe catch-up growth after antiretroviral therapy (ART) initiation among children living with human immunodeficiency virus (CLHIV), attending a private clinic in India. This is a retrospective analysis of data of CLHIV attending Prayas clinic, Pune, India. Height and weight z scores (HAZ, WAZ) were calculated using WHO growth charts. Catch-up growth post-ART was assessed using a mixed method model in cases where baseline and at least one subsequent follow-up HAZ/WAZ were available. STATA 12 was used for statistical analysis. During 1998 to 2011, 466 children were enrolled (201 girls and 265 boys; median age = 7 y). A total of 302 children were ever started on ART; of which 73 and 76 children were included for analysis for catch up growth in WAZ and HAZ respectively. Median WAZ and HAZ increased from -2.14 to -1.34 (p = 0.007) and -2.42 to -1.94 (p = 0.34), respectively, 3 y post ART. Multivariable analysis using mixed model (adjusted for gender, guardianship, baseline age, baseline WAZ/HAZ, baseline and time varying WHO clinical stage) showed gains in WAZ (coef = 0.2, 95 % CI: -0.06 to 0.46) and HAZ (coef = 0.49, 95 % CI: 0.21 to 0.77) with time on ART. Lower baseline WAZ/HAZ and older age were associated with impaired catch-up growth. Children staying in institutions and with baseline advanced clinical stage showed higher gain in WAZ. The prevalence of stunting and underweight was high at ART initiation. Sustained catch-up growth was seen with ART. The study highlights the benefit of early ART in achieving normal growth in CLHIV.

Atom-Probe Tomographic Investigation of Austenite Stability and Carbide Precipitation in a TRIP-Assisted 10 Wt Pct Ni Steel and Its Weld Heat-Affected Zones

Science.gov (United States)

Jain, Divya; Seidman, David N.; Barrick, Erin J.; DuPont, John N.

2018-04-01

Newly developed low-carbon 10 wt pct Ni-Mo-Cr-V martensitic steels rely on the Ni-enriched, thermally stable austenite [formed via multistep intercritical Quench-Lamellarization-Tempering ( QLT)-treatment] for their superior mechanical properties, specifically ballistic resistance. Critical to the thermal stability of austenite is its composition, which can be severely affected in the weld heat-affected zones (HAZs) and thus needs investigations. This article represents the first study of the nanoscale redistributions of C, Ni, and Mn in single-pass HAZ microstructures of QLT-treated 10 wt pct Ni steels. Local compositions of Ni-rich regions (representative of austenite compositions) in the HAZs are determined using site-specific 3-D atom-probe tomography (APT). Martensite-start temperatures are then calculated for these compositions, employing the Ghosh-Olson thermodynamic and kinetics approach. These calculations predict that austenite (present at high temperatures) in the HAZs is susceptible to a martensitic transformation upon cooling to room temperature, unlike the austenite in the QLT-treated base-metal. While C in the QLT-treated base-metal is consumed primarily in MC and M2C-type carbide precipitates (M is Mo, Cr, V), its higher concentration in the Ni-rich regions in the HAZs indicates the dissolution of carbide precipitates, particularly M2C carbide precipitates. The role of M2C carbide precipitates and austenite stability is discussed in relation to the increase in microhardness values observed in the HAZs, relative to the QLT-treated base-metal. Insights gained from this research on austenite stability and carbide precipitation in the single-pass HAZ microstructures will assist in designing multiple weld cycles for these novel 10 wt pct Ni steels.

Knowledge acquisition on hazards in chemical and process industry

Energy Technology Data Exchange (ETDEWEB)

Vojnovic, D; Kozuh, M [Inst. Jozef Stefan, Ljubljana (Slovenia)

1992-07-01

The knowledge acquisition for probabilistic risk assessment and operational safety improvements are described. The procedure HazOp (Hazard and Operability Study) are used for hazard identification. The acquainted knowledge is condensed in the form of cause-consequence matrix which is very convenient for plant logic model start point definition. At the end, the possibility for HazOp performance support by use of Artificial Intelligence approach is considered. (author) [Slovenian] V clanku se obravnava zbiranje znanja za potrebe verjetnostne ocene tveganja in izboljsanja obratovalne varnosti. Opisan je postopek za razpoznavanje nevarnosti po metodi HazOp. Zbrano znanje je predstavljeno v obliki vzrocno posledicne matrike, kar je primerna oblika za nadaljno uporabo pri logicnem modeliranju objekta. Ravno tako je obravnavana moznost uporabe diagnosticnih metod (umetna inteligenca) pri HazOp analizi. [author].

Microstructural and hardness investigations on a dissimilar metal weld between low alloy steel and Alloy 82 weld metal

International Nuclear Information System (INIS)

Chen, Z.R.; Lu, Y.H.; Ding, X.F.; Shoji, T.

2016-01-01

The investigation on microstructure and hardness at the fusion boundary (FB) region of a dissimilar metal weld (DMW) between low alloy steel (LAS) A508-III and Alloy 82 weld metal (WM) was carried out. The results indicated that there were two kinds of FBs, martensite FB and sharp FB, with obvious different microstructures, alternately distributed in the same FB. The martensite FB region had a gradual change of elemental concentration across FB, columnar WM grains with high length/width ratios, a thick martensite layer and a wide heat affected zone (HAZ) with large prior austenite grains. By comparison, the sharp FB region had a relatively sharp change of elemental concentration across the FB, WM grains with low length/width ratios and a narrow HAZ with smaller prior austenite grains. The martensite possessed a K-S orientation relationship with WM grains, while no orientation relationship was found between the HAZ grains and WM grains at the sharp FB. Compared with sharp FB there were much more Σ3 boundaries in the HAZ beside martensite FB. The hardness maximum of the martensite FB was much higher than that of the sharp FB, which was attributed to the martensite layer at the martensite FB. - Highlights: •Martensite and sharp FBs with different microstructures were found in the same FB. •There were high length/width-ratio WM grains and a wide HAZ beside martensite FB. •There were low length/width-ratio WM grains and a narrow HAZ beside sharp FB. •Compared with sharp FB, there were much more Σ3 boundaries in HAZ of martensite FB. •Hardness maximium of martensite FB was much higher than that of sharp FB.

Enhancement of the quality of the reactor pressure vessel used in light water power plants by advanced material, fabrication and testing technologies

International Nuclear Information System (INIS)

Kussmaul, K.; Ewald, J.; Maier, G.; Schellhammer, W.

1980-01-01

Fracture safe assessment of nuclear reactor pressure vessels (RPV) is based upon an adequate stress analysis, reliable material characteristics, and acceptable defect sizes. Problems may arise concerning inhomogeneties, low toughness and crack phenomena as observed in the base material and heat affected zone (HAZ). Therefore, efforts have been made to develop a steel which would be both non-susceptible to embrittlement and/or cracking in the HAZ, and have a higher upper-shelf toughness of base and HAZ material. Tests have been made on inhomogeneties and defects and also on improvement of chemical composition, the steel-making process, welding procedures and the optimum temperature cycle and level for stress-relief heat treatment. To solve these problems, common testing methods were supplemented by tangential-cut techniques, small HAZ-tensile test procedures and HAZ-simulation techniques. Results indicate that 50 per cent of 100 investigated component-strength welds are affected by micro stress-relief cracking (SRC) on a micro-and millimetre scale. The 22 NiMoCr 37 steel with optimised chemical composition, and the 20 MnMoNi 55 steel are both resistant to stress-relief embrittlement and SRC. Specific welding techniques are found to limit SRC and proposals for optimum stress-relief temperatures are given. For the generation of new components, the fracture-safe analysis can now be based completely upon homogeneous and high upper-shelf base materials including the HAZ. (author)

Influence of childcare practices on nutritional status of Ghanaian children: a regression analysis of the Ghana Demographic and Health Surveys.

Science.gov (United States)

Amugsi, Dickson A; Mittelmark, Maurice B; Lartey, Anna; Matanda, Dennis J; Urke, Helga B

2014-11-03

Guided by the UNICEF framework for childcare, this study examined the association of childcare practices (CCP) with infant and young children's growth (height-for-age Z-scores, HAZ), and investigated whether care practices are more important to growth in some sociodemographic subgroups of children. Cross-sectional survey. Urban and rural Ghana. The study sample comprised 1187 dyads of mothers aged 15-49 years and their youngest child (aged 6-36 months). The results showed that CCP was a significant predictor of HAZ, after controlling for covariates/confounders at child, maternal and household levels. Children with higher CCP scores had higher HAZ. A 1-unit increase in the CCP score was associated with a 0.17-unit increase in HAZ. Child's and mother's age, number of children under 5 years, place of residence, maternal weight and wealth index were also significantly associated with HAZ. Statistical interaction analyses revealed no subgroup differences in the CCP/HAZ relationship. This study found a significant, positive association between CCP and child growth, after accounting for other important determinants of child growth at maternal and household levels. This calls for research into the effects on growth of various CCP components, with longitudinal cohort study designs that can disentangle causal relationships. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Microstructure and mechanical properties in the weld heat affected zone of 9Cr-2W-VTa reduced activation ferritic/martensitic steel for fusion

Energy Technology Data Exchange (ETDEWEB)

Moon, Joonoh; Lee, Changhoon; Lee, Taeho; Jang, Minho; Park, Mingu [Korea Institute of Materials Science, Changwon (Korea, Republic of); Kim, Hyoung Chan [National Fusion Research Institute, Daejeon (Korea, Republic of)

2014-05-15

Reduced activation ferritic/martensitic (RAFM) steel demonstrated excellent resistance to the neutron irradiation and mechanical properties. The investigation of weldability in company with the development of RAFM steel is essential for construction of the fusion reactor. Generally, the superior mechanical properties of the RAFM steel can be upset during welding process due to microstructural change by rapid heating and cooling in the weld heat affected zone (HAZ). The phase transformation and mechanical properties in the weld HAZ of RAFM steel were investigated. The base steel consisted of tempered martensite and two carbides. During rapid welding thermal cycle, the microstructure of the base steel was transformed into martensite and δ-ferrite. In addition, the volume fraction of δ-ferrite and grain size increased with increase in the peak temperature and heat input. The strength of the HAZs was higher than that of the base steel due to the formation of martensite, whereas the impact properties of the HAZs deteriorated as compared with the base steel due to the formation of δ-ferrite. The PWHT improved the impact properties of the HAZs, resulting from the formation of tempered martensite.

Cracking in fusion zone and heat affected zone of electron beam welded Inconel-713LC gas turbine blades

Energy Technology Data Exchange (ETDEWEB)

Chamanfar, A., E-mail: achamanfar@gmail.com [Département de Génie Mécanique, École de Technologie Supérieure, 1100 rue Notre-Dame Ouest, Montréal, Québec, Canada H3C 1K3 (Canada); Jahazi, M. [Département de Génie Mécanique, École de Technologie Supérieure, 1100 rue Notre-Dame Ouest, Montréal, Québec, Canada H3C 1K3 (Canada); Bonakdar, A.; Morin, E. [Siemens Canada Limited, 9545 Côte-de-Liesse, Dorval, Québec, Canada H9P 1A5 (Canada); Firoozrai, A. [Département de Génie Mécanique, École de Technologie Supérieure, 1100 rue Notre-Dame Ouest, Montréal, Québec, Canada H3C 1K3 (Canada)

2015-08-26

Electron beam welding (EBW) of shrouds in Inconel-713LC low pressure gas turbine blades was associated with cracking in fusion zone (FZ) and heat affected zone (HAZ) leading to a high scrap rate in manufacturing of gas turbine blades. In this study, in order to develop a detailed map of cracks and understand the root cause of cracking, a comprehensive microstructural and numerical analysis was performed. The elemental mapping in scanning electron microscope (SEM)-energy dispersive spectral analysis revealed segregation of alloying elements in the cracked area of FZ and HAZ. In other words, one of the cracking mechanisms in FZ and HAZ was found to be segregation induced liquation and subsequent cracking due to thermal and mechanical tensile stresses generated during EBW. Cracking in FZ also occurred because of low strength of the solidifying weld metal as well as solidification contraction. As well, γ′ dissolution and reprecipitation in HAZ leading to decreased ductility and generation of contraction stresses was another mechanism for cracking in HAZ. The numerical model was capable to predict the cracking location as well as cracking orientation with respect to the weld line.

Influence of microstructure of high-strength low-alloy steels on their weldability

International Nuclear Information System (INIS)

Cwiek, J.; Labanowski, J.

2003-01-01

Microstructure of steel before welding has influence on the steel's susceptibility to cold cracking because it influences hardenability and maximum hardness of heat affected zone (HAZ). Two high-strength low-alloy (HSLA) steel grades 18G2AV and 14HNMBCu, in various heat treatment conditions, were subjected to simulated welding thermal cycles. It was revealed that maximum HAZ hardness is influenced by microstructure presented before thermal cycle was applied. The higher HAZ hardness was observed for quenched and tempered condition, comparing to full annealed and overheated conditions. (author)

Study on the welding continuous cooling transformation and weldability of SA508Gr4 steel for nuclear pressure vessels

International Nuclear Information System (INIS)

Bai, Qingwei; Ma, Yonglin; Xing, Shuqing; Chen, Zhongyi

2017-01-01

SA508Gr4 is a newly developed high-strength steel for nuclear reactor pressure vessels. Its welding characteristics remain largely unexplored. In this work, the simulated heat affected zone continuous cooling transformation (SH-CCT) diagram of SA508Gr4 steel was constructed and the high-temperature cooling phase compositions and the properties of the heat affected zone (HAZ) were characterized using dilatometry and microscopic tests. The results show that the phase transformation in the HAZ was divided into bainite and martensite transformation stages. When 4.6 ≤ t_8_/_5 (the HAZ cooling time from 800 C to 500 C) ≤ 15 s, lath-shaped martensite was fully developed, resulting in extensive hardening and cold cracking in the HAZ, while the cooling time required to form the bainite completely exceeds 1 200 s. Thus, to improve weld quality, preheating to 196 C or higher is recommended.

The feasibility of welding irradiated materials

Science.gov (United States)

Lin, H. T.; Chin, B. A.

1991-03-01

Helium was implanted into solution-annealed (SA) 316 stainless steel, 20% cold-worked (CW) 316 stainless steel and titanium-modified Primary Candidate Alloy (PCA) through tritium decay to levels ranging from 0.18 to 256 appm. Full penetration welds were then made on helium-doped materials using gas tungsten arc welding (GTAW) under fully constrained conditions. Intergranular heat-affected zone (HAZ) cracking was observed in all of the materials containing greater than 1 appm He. Electron microscopy showed that the HAZ cracking originated from the growth and coalescence of grain boundary (GB) helium bubbles. Bubble growth kinetics in the HAZ is explained by stress-enhanced diffusive cavity growth. Results suggest that the propensity for HAZ cracking can be reduced by the pre-existing cold-worked structure and by finely-distributed MC precipitates that refine the distribution of helium bubbles and minimize the flow of vacancies in grain boundaries.

Study on the welding continuous cooling transformation and weldability of SA508Gr4 steel for nuclear pressure vessels

Energy Technology Data Exchange (ETDEWEB)

Bai, Qingwei; Ma, Yonglin; Xing, Shuqing; Chen, Zhongyi [Inner Mongolia Univ. of Science and Technology, Baotou (China). School of Material and Metallurgy; Kang, Xiaolan [Baotou Vocational and Technical College (China)

2017-02-15

SA508Gr4 is a newly developed high-strength steel for nuclear reactor pressure vessels. Its welding characteristics remain largely unexplored. In this work, the simulated heat affected zone continuous cooling transformation (SH-CCT) diagram of SA508Gr4 steel was constructed and the high-temperature cooling phase compositions and the properties of the heat affected zone (HAZ) were characterized using dilatometry and microscopic tests. The results show that the phase transformation in the HAZ was divided into bainite and martensite transformation stages. When 4.6 ≤ t{sub 8/5} (the HAZ cooling time from 800 C to 500 C) ≤ 15 s, lath-shaped martensite was fully developed, resulting in extensive hardening and cold cracking in the HAZ, while the cooling time required to form the bainite completely exceeds 1 200 s. Thus, to improve weld quality, preheating to 196 C or higher is recommended.

The feasibility of welding of irradiated materials

International Nuclear Information System (INIS)

Lin, H.T.; Chin, B.A.; Auburn Univ., AL

1989-01-01

Helium was implanted into solution-annealed (SA) 316 stainless steel, 20% cold-worked (CW) 316 stainless steel and titanium-modified Primary Candidate Alloy (PCA) through tritium decay to levels ranging from 0.18 to 256 appm. Full penetration welds were then made on helium-doped materials using gas tungsten arc welding (GTAW) under fully constrained conditions. Intergranular heat-affected zone (HAZ) cracking was observed in all of the materials containing greater than 1 appm He. Electron microscopy showed that the HAZ cracking originated from the growth and coalescence of grain boundary (GB) helium bubbles. Bubble growth kinetics in the HAZ is explained by stress-enhanced diffusive cavity growth. Results suggest that the propensity for HAZ cracking can be reduced by the preexisting cold-worked structure and by finely-distributed MC precipitates that refine the distribution of helium bubbles and minimize the flow of vacancies in grain boundaries. 16 refs., 3 figs

Reheat cracking in austenitic stainless steels; Fissuration en relaxation des aciers inoxydables austenitiques

Energy Technology Data Exchange (ETDEWEB)

Auzoux, Q.; Allais, L. [CEA Saclay, Dept. des Materiaux pour le Nucleaire, DMN, 91 - Gif sur Yvette (France); Pineau, A.; Gourgues, A.F. [Centre des Materiaux Pierre-Marie Fourt UMR CNRS 7633, 91 - Evry (France)

2002-07-01

Intergranular cracking can occur in heat-affected zones (HAZs) of austenitic stainless steel welded joints when reheated in the temperature range from 500 to 700 deg C. At this temperature, residual stresses due to welding relax by creep flow. HAZ may not sustain this small strain if its microstructure has been sufficiently altered during welding. In order to precise which particular microstructure alteration causes such an intergranular embrittlement, type 316L(N) HAZs were examined by transmission electron microscopy. A marked increase in the dislocation density, due to plastic strain during the welding process, was revealed, which caused an increase in Vickers hardness. Type 316L(N) HAZ were then simulated by the following thermal-mechanical process: annealing treatment and work hardening (pre-strain). Creep rupture tests on smooth specimens were also carried out at 600 deg C on both base metal and simulated HAZ. Pre-straining increased creep strength but reduced ductility. Slow strain rate tests on CT specimens confirmed this trend as well as did relaxation tests on CT specimens, which led to intergranular crack propagation in the pre-strained material only. Metallography and fractography showed no qualitative difference between base metal and HAZs in the creep cavitation around intergranular carbides. Although quantitative study of damage development is not achieved yet, experiments suggest that uniaxial creep strain smaller than one percent could lead to cavity nucleation when the material is pre-strained. Pre-strain as well as stress triaxiality reduce therefore creep ductility and enhance the reheat cracking risk. (authors)

Controlled, all-position, butterbead-temperbead welding technique for nuclear repairs

International Nuclear Information System (INIS)

Clark, J.N.; Lambert, J.A.

1986-01-01

Sections III and XI of the ASME boiler and pressure vessel code describe a half-bead temper repair welding technique specifically designed for in-service BWR and PWR repair applications without postweld heat treatment. The method relies on deposition of two layers of weld beads. Prior to deposition of the second layer, half the first layer is ground away. As a result, the first layer HAZ is tempered or retransformed by the second layer heat input. It is on the basis of this tempering that a concession is granted to omit postweld heat treatment. The grinding stage is difficult to control, time consuming, and can involve long exposure of personnel to a radioactive environment. Consequently, there has been pressure to find a viable alternative to the half-bead technique. Much interest has been shown in the butterbead-temperbead technique, which is essentially the CEGB two-layer HAZ refinement technique. This does not require grinding of the first layer and achieves HAZ retransformation by increasing the heat input of the second layer. The elimination of the grinding stage considerably reduces repair time and, consequently, radiation exposure. The method has now been included as an acceptable alternative to the half-bead technique in section XI of the ASME code. The CEGB method has been used successfully in the U.K. power industry, mainly for prevention of stress relief cracking, but also to improve HAZ toughness for low temperature service. Two-layer HAZ refinement is achieved by retransformation of the first layer HAZ by the thermal field of the second layer

Improved simulation method of automotive spot weld failure with an account of the mechanical properties of spot welds

Science.gov (United States)

Wu, H.; Meng, X. M.; Fang, R.; Huang, Y. F.; Zhan, S.

2017-12-01

In this paper, the microstructure and mechanical properties of spot weld were studied, the hardness of nugget and heat affected zone (HAZ) were also tested by metallographic microscope and microhardness tester. The strength of the spot weld with the different parts' area has been characterized. According to the experiments result, CAE model of spot weld with HAZ structure was established, and simulation results of different lap-shear CAE models were analyzed. The results show that the spot weld model which contained the HAZ has good performance and more suitable for engineering application in spot weld simulation.

Intergranular corrosion susceptibility in supermartensitic stainless steel weldments

Energy Technology Data Exchange (ETDEWEB)

Aquino, J.M. [Sao Carlos Federal University (UFSCar), Materials Engineering Department, Rodovia Washington Luis, km 235, CEP 13565-905, Sao Carlos, SP (Brazil)], E-mail: dsek@power.ufscar.br; Della Rovere, C.A.; Kuri, S.E. [Sao Carlos Federal University (UFSCar), Materials Engineering Department, Rodovia Washington Luis, km 235, CEP 13565-905, Sao Carlos, SP (Brazil)

2009-10-15

The intergranular corrosion susceptibility in supermartensitic stainless steel (SMSS) weldments was investigated by the double loop - electrochemical potentiokinetic reactivation (DL-EPR) technique through the degree of sensitization (DOS). The results showed that the DOS decreased from the base metal (BM) to the weld metal (WM). The heat affected zone (HAZ) presented lower levels of DOS, despite of its complex precipitation mechanism along the HAZ length. Chromium carbide precipitate redissolution is likely to occur due to the attained temperature at certain regions of the HAZ during the electron beam welding (EBW). Scanning electron microscopy (SEM) images showed preferential oxidation sites in the BM microstructure.

Assessment of weld heat-affected zones in a reactor vessel material

International Nuclear Information System (INIS)

Marston, T.U.; Server, W.

1978-01-01

The mechanical properties of weld heat-affected zones (HAZ's) associated with the heavy section, nuclear quality weldments are evaluated and found to be superior to those of the parent base material. The nil ductility transition temperature (NDTT), Charpy impact and static and dynamic fracture toughness properties of a HAZ associated with a submerged arc weld and one associated with a manual metal arc weld are directly compared with those of the parent base material. It is concluded that the stigma normally associated with HAZ is not justified for this grade and quality of material and weld procedure

An Investigation of TIG welding parameters on microhardness and microstructure of heat affected zone of HSLA steel

Science.gov (United States)

Musa, M. H. A.; Maleque, M. A.; Ali, M. Y.

2018-01-01

Nowadays a wide variety of metal joining methods are used in fabrication industries. In this study, the effect of various welding parameters of the TIG welding process on microhardness, depth, and microstructure of the heat-affected zone (HAZ) of L450 HSLA steel and optimizing these process parameters following Taguchi experimental design was investigated. The microhardness tended to increase significantly with the increase of welding speed from 1.0 to 2.5 mm/s whereas the width of HAZ decreased. The current and arc voltage was found to be less significant in relative comparison. Microstructures of the welded samples were also studied to analyze the changes in the microstructure of the material in terms of ferrite, pearlite, bainite, and martensite formations. Welding speed was found to be the most significant factors leading to changes in microhardness and metallurgical properties. The increase of welding heat input caused an increase in width (depth) of HAZ and the growth of prior austenite grains and then enlarged the grain size of coarse grain heat affected zone (CGHAZ). However, the amount of martensite in the HAZ decreased accompanied by an opposite change of paint. It was observed that the hardness properties and the microstructural feature of HAZ area was strongly affected by the welding parameters.

The effect of gas tungsten arc welding and pulsed-gas tungsten arc welding processes’ parameters on the heat affected zone-softening behavior of strain-hardened Al–6.7Mg alloy

International Nuclear Information System (INIS)

Hadadzadeh, Amir; Ghaznavi, Majid Mahmoudi; Kokabi, Amir Hossein

2014-01-01

Highlights: • The strain-hardened Al–6.7Mg alloy was welded using GTAW and PGTAW processes. • The HAZ softening behavior of the welding joint was characterized. • Employing pulsed current in GTAW process eliminated the HAZ softening. • Duration ratio did not affect the weld strength while the frequency influenced it. - Abstract: The heat affected zone (HAZ) softening behavior of strain-hardened Al–6.7Mg alloy welded by gas tungsten arc welding (GTAW) process was investigated. Increasing the heat input during welding led to formation of a wider HAZ. Moreover, the size of the precipitates was increased at higher heat inputs. Consequently, by increasing the heat input, lower strength was obtained for the welding joints. At the second stage of the study, pulsed-GTAW (PGTAW) process was employed to improve the strength of the joints. It was observed that the overall strength of the welding joints was improved and the fracture during tensile test was moved from the HAZ to the fusion zone. Moreover, the effect of duration ratio and pulse frequency was studied. For the current study, the duration ratio did not have a significant effect on the strength and microstructure of the weld, but increasing the frequency led to higher strength of the weld and finer microstructure

Investigation of the Microstructure of Laser-Arc Hybrid Welded Boron Steel

Science.gov (United States)

Son, Seungwoo; Lee, Young Ho; Choi, Dong-Won; Cho, Kuk-Rae; Shin, Seung Man; Lee, Youngseog; Kang, Seong-Hoon; Lee, Zonghoon

2018-05-01

The microstructure of boron steel for automotive driving shaft manufacturing after laser-arc hybrid welding was investigated. Laser-arc hybrid welding technology was applied to 3-mm-thick plates of boron steel, ST35MnB. The temperature distribution of the welding pool was analyzed using the finite element method, and the microstructure of the welded boron steel was characterized using optical microscopy and scanning and transmission electron microscopies. The microstructure of the weld joint was classified into the fusion zone, the heat-affected zone (HAZ), and the base material. At the fusion zone, the bainite grains exist in the martensite matrix and show directionality because of heat input from the welding. The HAZ is composed of smaller grains, and the hardness of the HAZ is greater than that of the fusion zone. We discuss that the measured grain size and the hardness of the HAZ originate from undissolved precipitates that retard the grain growth of austenite.

Microstructure and Mechanical Properties of Laser Welded Joints of DZ125L and IN718 Nickel Base Superalloys

Science.gov (United States)

Liang, Taosha; Wang, Lei; Liu, Yang; Song, Xiu

2018-05-01

The microstructure and mechanical properties of the laser welded joint of DZ125L and IN718 nickel base superalloys were investigated. The results show that the fusion zone (FZ) mainly consists of fine dendrite structure with fine γ', Laves phases and MC carbides inhomogeneously distributed. The high welding temperature induces the partial dissolution of γ' in the heat-affected zone (HAZ) of DZ125L and liquation of grain boundaries in both of the HAZs. After post-weld heat treatment (PWHT), fine γ″ and γ' phases precipitate in the FZ, IN718 HAZ and IN718 base metal (BM), and fine γ' precipitate in the γ channel of the HAZ and BM of DZ125L. With tensile testing, the joints after PWHT show higher strengths than that of the weaker DZ125L alloy. Plastic deformation mainly concentrates in the weaker DZ125L and the joint finally fails in the DZ125L BM.

Concurrent phase separation and clustering in the ferrite phase during low temperature stress aging of duplex stainless steel weldments

International Nuclear Information System (INIS)

Zhou, J.; Odqvist, J.; Thuvander, M.; Hertzman, S.; Hedström, P.

2012-01-01

The concurrent phase separation and clustering of alloying elements in the ferrite phase of duplex stainless steel weldments after stress aging at 325 °C have been investigated by atom probe tomography analysis. Both phase separation, into Fe-rich and Cr-rich ferrite, and solute clustering were observed. Phase separation in the heat-affected zone (HAZ) is most pronounced in the high alloyed SAF 2507, followed by SAF 2205 and SAF 2304. Moreover Cu clustering was observed in the HAZ of SAF 2507. However, decomposition in the weld bead (25.10.4L) was more pronounced than in the HAZs, with both phase separation and clustering of Ni–Mn–Si–Cu. The observed differences in the decomposition behaviors in the HAZ and weld bead can be attributed to the high Ni content and the characteristic microstructure of the weld bead with high internal strains. In addition, an applied tensile stress during aging of weldments has been found to further promote the kinetics of phase separation and clustering.

Characteristics of heat affected zone in SAW and SMAW welding of microalloyed steel 450 EMZ studied by means of a welding simulator

International Nuclear Information System (INIS)

Gonzalez Palma, R.; Carrillo Olivares, F.; Lopez Torres, E.

1997-01-01

In high elastic limit microalloyed steels the heat input remains limited to values around 3 kj/mm, since, from a theoretical point of view the metallurgic transformations produced in the heat affected zone (HAZ) may fragile the metal. The study of the transmission of heat in the HAZ from a theoretical point of view is carried out by solving Rosenthal's equation, which allows us to know the peak temperature reached and the heat cycle in every point of the HAZ. With these data and the CCT curves for 450 EMZ steel corresponding to our steel we will be able to determine the metallurgic transformations produced in those points, with the help of an electron microscope. The welding simulator is valuable help for laboratory study of heat cycles as it allows us to check that for the actual welding processes chosen, i.e. SMAW and SAW, and for the heat input, the transformation products obtained in the HAZ have the right toughness. (Author) 17 refs

Heat affected zone structure in welded joints of 15Kh1M1FL, 25Kh2NMFA and 20KhN2MFA steels

International Nuclear Information System (INIS)

Levenberg, N.E.; German, S.I.; Fomina, O.P.; Netesa, E.M.; Tsaryuk, A.K.; Kornienko, T.A.

1983-01-01

Heat affected zone (HAZ) structure of thick-walled, nature joints of 15Kh1M1FL steel for block structure of power reactors and 25Kh2NMFA and 20KhN2MFA steels for rotors - is investigated. Multi-layer arc welding is performed under conditions being created for standard components of turbines. Thermokinetics diagrams of austenite decomposition are built, phase composition and character of the structure forming at HAZ in the process of welding with preheating are studied. It is shown that at HAZ in joints of the steels under consideration in the process of welding with preheating is formed a structure of a grained bainite which is uniform in its structure and phase composition. Small volumes of round and elongated forms consisting of martensite and residual austenite are distributed in α-solid solution of the bainite. The bainite of the HAZ in welded joints possesses high hardness and great stability in the process of tempering

Cross-Sectional and Longitudinal Associations between Household Food Security and Child Anthropometry at Ages 5 and 8 Years in Ethiopia, India, Peru, and Vietnam.

Science.gov (United States)

Humphries, Debbie L; Dearden, Kirk A; Crookston, Benjamin T; Fernald, Lia C; Stein, Aryeh D; Woldehanna, Tassew; Penny, Mary E; Behrman, Jere R

2015-08-01

Poor childhood nutritional status has lifetime effects and food insecurity is associated with dietary practices that can impair nutritional status. We assessed concurrent and subsequent associations between food insecurity and height-for-age z scores (HAZs) and body mass index-for-age z scores (BMI-Zs); evaluated associations with transitory and chronic food insecurity; and tested whether dietary diversity mediates associations between food insecurity and nutritional status. We used data from the Young Lives younger cohort composed of children in Ethiopia (n = 1757), India (n = 1825), Peru (n = 1844), and Vietnam (n = 1828) recruited in 2002 (round 1) at ∼1 y old, with subsequent data collection at 5 y in 2006 (round 2) and 8 y in 2009 (round 3). Children from food-insecure households had significantly lower HAZs in all countries at 5 y (Ethiopia, -0.33; India, -0.53; Peru, -0.31; and Vietnam, -0.68 HAZ; all P Peru, -0.14; and Vietnam, -0.27 HAZ; P Peru. Age 5 y food insecurity predicted the age 8 y BMI-Z even after controlling for the 5 y BMI-Z, although associations were not significant after the inclusion of additional confounding variables (Ethiopia, P = 0.12; India, P = 0.29; Peru, P = 0.16; and Vietnam, P = 0.51). Chronically food-insecure households had significantly lower HAZs than households that were consistently food-secure, although BMI-Zs did not differ by chronic food-insecurity status. Dietary diversity mediated 18.8-30.5% of the association between food security and anthropometry in Vietnam, but mediated to a lesser degree (8.4-19.3%) in other countries. In 4 countries, food insecurity at 5 y of age was associated with both HAZ and BMI-Z at age 8 y, although the association was attenuated after adjusting for other household factors and anthropometry at age 5 y, and remained significant only for the HAZ in Vietnam. © 2015 American Society for Nutrition.

Characterisation of girth pipe weld for primary heat transport system of pressurised heavy water reactors

International Nuclear Information System (INIS)

Singh, P.K.; Vaze, K.K.; Kushwaha, H.S.

2002-01-01

The weld and heat affected zone (HAZ) associated with the girth weld are most vulnerable regions of the piping system. The different regions of the weld joint such as the weld metal, HAZ and base metal lead to heterogeneous mechanical and metallurgical properties of the joints. Due to their different metallurgical and mechanical properties, the amounts of damage produced in these regions are different when the component is subjected to service condition. Thus, it is imperative to know the characteristics of these regions of a pipe weld in order to identify the weakest zone for safe designing of high energy piping components. In view of this necessity the present study has been planned to carry out complete characterisation of the weld joint of SA 333 Gr.6 steel pipe, in terms of its metallurgical, mechanical and fracture properties. The mechanical and fracture mechanics properties of the base metal, weld deposit and HAZ have been compared and correlated with reference to their microstructures. Weld joints of SA 333 Gr.6 steel pipe have been prepared by using GTAW root pass and SMAW filling of V-grove as per recommended welding procedure specifications (WPS) conforming to ASME Sec IX commonly used to fabricate nuclear piping system components. The emphasis of the study is to characterise base, weld and HAZ of the pipe weld in terms of chemical, metallurgical, mechanical and fracture mechanics properties. The fracture toughness behaviour of the welds and HAZ has been characterised by J-integral parameters. The fatigue crack growth rate has been characterised by Paris Law. Stretched zone width (SZW) has been measured under SEM to evaluate initiation fracture toughness. The estimated initiation fracture toughness based on SZW and blunting line given by EGF recommendation have been compared. The fracture mechanics properties of base, weld and HAZ has been determined and compared. The fracture mechanics properties of the weld and HAZ have been correlated to their

Pretest analysis of the NESC-1 spinning cylinder experiment

Energy Technology Data Exchange (ETDEWEB)

Sattari-Far, Iradj [SAQ Inspection Ltd., Stockholm (Sweden)

1997-09-01

This report presents defect assessment results from a final pre-test analysis of the NESC-1 spinning cylinder based on the NDE defect definitions and the determined loading conditions. The analysis covers fracture assessments of a subclad and a surface breaking crack. Three-dimensional elastic-plastic finite element calculations, considering the crack-tip constraint, are employed in the assessment. Also performed are sensitivity studies to demonstrate how different affecting parameters, especially the cladding residual stresses, impact the crack driving force. It is found for both the surface and the subclad crack that the situations in the cladding and the deepest point of the crack front are far from critical for cleavage future. The results of the analysis indicate that a limited amount of ductile crack growth can occur along the crack front in the HAZ and adjacent base material. Cleavage fracture events can be expected in the HAZ. The results also show substantial loss of crack-tip constraint in the HAZ compared with the SSY solutions. Providing that the constraint and warm prestressing effects do not substantially affect the situations in HAZ, one can expect cleavage fracture to occur in the HAZ at a time around four minutes into the transient. From the sensitivity studies, it is observed that uncertainties due to different assumptions in the analysis, for instance crack depth and cladding residual stresses, influence the assessment results less than uncertainties of the fracture toughness properties of the materials. To perform a precise evaluation, fracture toughness data of the HAZ material corresponding to the actual constraint conditions are needed. 29 refs, 30 figs, 3 tabs.

Effect of micromorphology at the fatigue crack tip on the crack growth in electron beam welded Ti-6Al-4V joint

International Nuclear Information System (INIS)

Tao, Junhui; Hu, Shubing; Ji, Longbo

2016-01-01

In this paper, we describe experiments on welded joints of Ti-6Al-4V alloy specimens exhibiting fatigue characteristics in the base metal (BM), hot affected zone (HAZ) and fuse zone (FZ). The effect of micromorphology on crack propagation at the tip of the fatigue crack in joints formed by electron beam welding was investigated using an optical microscope, transmission electron microscope and other methodologies. The results demonstrated that the fatigue crack originated in and propagated along α/β boundaries in the BM. In the HAZ, the fatigue crack occurred at the boundary between martensite laths, and propagated through most irregular-equiaxed α phases and a few martensite laths. In the FZ, the fatigue crack originated at the boundaries between the fine crushing phases among martensite laths, and propagated along a majority of α/β boundaries and several narrow martensite laths. The electron beam welded joint of Ti-6Al-4V alloy showed instances of zigzag fatigue cracks that increased in degree from lowest in the HAZ, moderate in the FZ to greatest in the BM. Conversely, fatigue crack growth rate (FCGR) was greatest in the HAZ, less in the FZ and slowest in the BM. - Highlights: •Ti-6Al-4V welded joint exhibits different fatigue characteristics. •The fatigue crack propagates along α/β boundaries in the BM. •The fatigue crack propagates through α phases and martensite laths in the HAZ. •The fatigue crack propagates along α/β boundaries and martensite laths in the FZ. •Fatigue crack growth rate is fastest in the HAZ, less in the FZ, slowest in the BM.

Effect of Water Cooling on the Performances of Friction Stir Welding Heat-Affected Zone

Science.gov (United States)

Zhang, H. J.; Liu, H. J.; Yu, L.

2012-07-01

The heat-affected zone (HAZ) is generally the intrinsic weakest location of the normal friction stir welded precipitate hardened aluminum alloys. In order to improve the mechanical properties of the HAZ by controlling the temperature level, underwater friction stir welding (FSW) of an Al-Cu aluminum alloy was conducted in the present study. The results indicate that the hardness of the HAZ can be improved through underwater FSW. Microstructural analysis reveals that the hardness improvement is attributed to the lowering of precipitate coarsening level and the narrowing of precipitate free zone, which are essentially induced by the variations of welding thermal cycles under the cooling effect of water.

Microstructures of a welded joint using an irradiated wrapper tube

International Nuclear Information System (INIS)

Hamada, S.; Watanabe, K.; Hishinuma, A.; Takahashi, I.; Kikuchi, T.

1993-01-01

The behavior of helium in welded joint fabricated using tungsten inert gas (TIG) welding process for a type 316 stainless steel wrapper tube irradiated in a fast reactor was investigated. The wrapper tube was irradiated to (1.5 - 4.2) x 10 26 n/m 2 (helium level of 3 to 9 appm) at 395 - 410 degrees C. All welded joints fractured in the heat-affected zone (HAZ). The microstructures of each portion of the base metal, the HAZ and the fusion zone in a welded joint were examined through a transmission electron microscope. Small helium bubbles were observed in number density of 2 x 10 20 m -3 in the matrix and rarely found on the grain boundaries of the base metal. In the HAZ, small and large helium bubbles mixed and lined up along the grain boundaries. In particular, some of them elongated along the grain boundary. In the matrix of the fusion zone, delta-ferrite phases and unresolved carbides were scattered. Large cavities were attached to these precipitates and also occurred along grain boundaries. These results suggest that the failure in the HAZ of welded joints is attributed to the preferential growth and coalescence of helium bubbles in the grain boundaries of the HAZ caused by weld heat input and stress during welding

Proposal of fatigue crack growth rate curve in air for nickel-base alloys used in BWR

International Nuclear Information System (INIS)

Ogawa, Takuya; Itatani, Masao; Nagase, Hiroshi; Aoike, Satoru; Yoneda, Hideki

2013-01-01

When the defects are detected in the nuclear components in Japan, structural integrity assessment should be performed for the technical judgment on continuous service based on the Rules on Fitness-for-Service for Nuclear Power Plants of the Japan Society of Mechanical Engineers Code (JSME FFS Code). Fatigue crack growth analysis is required when the cyclic loading would be applied for the components. Recently, fatigue crack growth rate curve in air environment for Nickel-base alloys weld metal used in BWR was proposed by the authors and it was adopted as a code case of JSME FFS Code to evaluate the embedded flaw. In this study, fatigue crack growth behavior for heat-affected zone (HAZ) of Nickel-base alloys in air was investigated. And a unified fatigue crack growth rate curve in air for HAZ and weld metal of Nickel-base alloys used in BWR was evaluated. As a result, it was found that the curve for weld metal could be applied as a curve for both HAZ and weld metal since moderately conservative assessment of fatigue crack growth rate of HAZ is possible by the curve for weld metal in the Paris region. And the threshold value of stress intensity far range (ΔK th ) is determined to 3.0 MPa√m based on the fatigue crack growth rate of HAZ. (author)

Effect of welding processes on the impression creep resistance of type 316 LN stainless steel weld joints

International Nuclear Information System (INIS)

Vasudevan, M.; Vasantharaja, P.; Sisira, P.; Divya, K.; Ganesh Sundara Raman, S.

2016-01-01

Type 316 LN stainless steel is the major structural material used in the construction of fast breeder reactors. Activated Tungsten Inert Gas (A-TIG) welding , a variant of the TIG welding process has been found to enhance the depth of penetration significantly during autogenous welding and also found to enhance the creep rupture life in stainless steels. The present study aims at comparing the effect of TIG and A-TIG welding processes on the impression creep resistance of type 316 LN stainless steel base metal, fusion zone and heat affected zone (HAZ) of weld joints. Optical and TEM have been used to correlate the microstructures with the observed creep rates of various zones of the weld joints. Finer microstructure and higher ferrite content was observed in the TIG weld joint fusion zone. Coarser grain structure was observed in the HAZ of the weld joints. Impression creep rate of A-TIG weld joint fusion zone was almost equal to that of the base metal and lower than that of the TIG weld joint fusion zone. A-TIG weld joint HAZ was found to have lower creep rate compared to that of conventional TIG weld joint HAZ due to higher grain size. HAZ of the both the weld joints exhibited lower creep rate than the base metal. (author)

Evaluation of strength property variations across 9Cr-1Mo steel weld joints using automated ball indentation (ABI) technique

International Nuclear Information System (INIS)

Nagaraju, S.; GaneshKumar, J.; Vasantharaja, P.; Vasudevan, M.; Laha, K.

2017-01-01

The variations of strength properties across 9Cr-1Mo steel weld joints fabricated by different arc welding processes such as shielded metal arc welding (SMAW), tungsten inert gas (TIG) and activated tungsten inert gas (A-TIG) have been evaluated employing automatic ball indentation (ABI) technique. ABI tests were conducted at 298 K across various zones of the weld joints comprising of base metal, weld metal, heat affected zone (HAZ) and intercritical HAZ (ICHAZ) regions. The flow curves obtained from ABI tests were correlated with corresponding conventional tensile test results. In general, the tensile strength decreased systematically across the weld joint from weld metal to base metal. Inter critical HAZ exhibited the least strength implying that it is the weakest zone. The incomplete phase transformation in the ICHAZ during weld thermal cycle caused the softening. The A-TIG weld metal exhibited higher UTS and strain hardening values due to higher carbon in the martensite. The strain hardening exponent exhibited only slight variation across the various regions of the weld joints. A-TIG weld joint exhibited higher weld metal and HAZ strength, marginally higher UTS to YS ratio in the weld metal and HAZ compared to that of the other two processes. Hence, among the three welding processes chosen, A-TIG welding process is found to be superior in producing a 9Cr-1Mo steel weld joint with better strength properties.

Evaluation of strength property variations across 9Cr-1Mo steel weld joints using automated ball indentation (ABI) technique

Energy Technology Data Exchange (ETDEWEB)

Nagaraju, S. [Nuclear Recycle Board, BARCF, Kalpakkam (India); GaneshKumar, J.; Vasantharaja, P. [Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research, Kalpakkam (India); Vasudevan, M., E-mail: dev@igcar.gov.in [Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research, Kalpakkam (India); Laha, K. [Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research, Kalpakkam (India)

2017-05-17

The variations of strength properties across 9Cr-1Mo steel weld joints fabricated by different arc welding processes such as shielded metal arc welding (SMAW), tungsten inert gas (TIG) and activated tungsten inert gas (A-TIG) have been evaluated employing automatic ball indentation (ABI) technique. ABI tests were conducted at 298 K across various zones of the weld joints comprising of base metal, weld metal, heat affected zone (HAZ) and intercritical HAZ (ICHAZ) regions. The flow curves obtained from ABI tests were correlated with corresponding conventional tensile test results. In general, the tensile strength decreased systematically across the weld joint from weld metal to base metal. Inter critical HAZ exhibited the least strength implying that it is the weakest zone. The incomplete phase transformation in the ICHAZ during weld thermal cycle caused the softening. The A-TIG weld metal exhibited higher UTS and strain hardening values due to higher carbon in the martensite. The strain hardening exponent exhibited only slight variation across the various regions of the weld joints. A-TIG weld joint exhibited higher weld metal and HAZ strength, marginally higher UTS to YS ratio in the weld metal and HAZ compared to that of the other two processes. Hence, among the three welding processes chosen, A-TIG welding process is found to be superior in producing a 9Cr-1Mo steel weld joint with better strength properties.

The oxidation behavior of three different zones of welded Incoloy 800H alloy

International Nuclear Information System (INIS)

Chen, W.S.; Kai, W.; Tsay, L.W.; Kai, J.J.

2014-01-01

Highlights: • The oxidation kinetics of 800H followed the parabolic-rate law in dry-air. • The scales formed on the alloys were composed of Cr 2 O 3 and MCr 2 O 4 (M = Fe, Cr). • Internal-oxidation of Al 2 O 3 and SiO 2 dissolved T i were observed in 800H-SUB and 800H-HAZ • The weight loss behavior of 800H-SUB and 800H-HAZ were observed in wet air. • The mass-loss behavior of 800H-HAZ is more severe than 800H-SUB in wet air. - Abstract: The oxidation behavior of three different zones of welded Incoloy 800H alloys, containing the substrate (800H-SUB), heat-affected zone (800H-HAZ) and the melt zone (800H-MZ) was studied at 950 °C in dry and wet air. The steady-state oxidation rate constants (k p values) were calculated based on the mass-gain data, and the oxidation resistant ability of the alloys followed by the rank of 800H-MZ > 800H-SUB > 800H-HAZ in dry air. The scales formed on the 800H-SUB and 800H-HAZ consisted of a heterophasic mixture of Cr 2 O 3 and FeCr 2 O 4 , while a mixture of Cr 2 O 3 and MnCr 2 O 4 was observed on the 800H-MZ. On the other hand, the oxidation kinetics of the alloy, initially followed the parabolic-rate law up to 48 h, while a significant mass-lost kinetics was observed for a prolong exposure in wet air. The detail oxidation mechanisms for the alloys in both environments were investigated

An investigation of laser cutting quality of 22MnB5 ultra high strength steel using response surface methodology

Science.gov (United States)

Tahir, Abdul Fattah Mohd; Aqida, Syarifah Nur

2017-07-01

In hot press forming, changes of mechanical properties in boron steel blanks have been a setback in trimming the final shape components. This paper presents investigation of kerf width and heat affected zone (HAZ) of ultra high strength 22MnB5 steel cutting. Sample cutting was conducted using a 4 kW Carbon Dioxide (CO2) laser machine with 10.6 μm wavelength with the laser spot size of 0.2 mm. A response surface methodology (RSM) using three level Box-Behnken design of experiment was developed with three factors of peak power, cutting speed and duty cycle. The parameters were optimised for minimum kerf width and HAZ formation. Optical evaluation using MITUTOYO TM 505 were conducted to measure the kerf width and HAZ region. From the findings, laser duty cycle was crucial to determine cutting quality of ultra-high strength steel; followed by cutting speed and laser power. Meanwhile, low power intensity with continuous wave contributes the narrowest kerf width formation and least HAZ region.

The Influence of Flow and Type of Variation in The Welding Electrode SMAW Against Carbon Steel Mechanical Propertis

Directory of Open Access Journals (Sweden)

I Made Gatot Karohika

2012-11-01

Full Text Available Welding is a joining process of 2 or more metal that is widely used in industry. To obtain good welding result it is needed appropriate filler and weld parameters to avoid weld defect and wide deference of mechanic properties between welded metal and base metal.In this experiment we used different filler and current (E 6010, 7018 ? 2,5mm ? 350mm , 100 dan 130 Aand use material carbon steel AISI 1045 and SMAW welding method. Rockwell C Hardness tested in welded metal, HAZ, and base metal area.The hardness number in welded metal and HAZ is reported higher than base metal area, the hardness number of welded metal and HAZ that use current 130 is higher than that one than use current 100 A,and hardness number in base metal relatifely similar. The hardness number of welded metal that use electrode 7018 is higher than hardness number of welded metal that use electrode 6010, and hardness number of HAZ and base metal is not affected significantly by the types of electrode.

Individual genetic variations related to satiety and appetite control increase risk of obesity in preschool-age children in the STRONG kids program.

Science.gov (United States)

Wang, Yingying; Wang, Anthony; Donovan, Sharon M; Teran-Garcia, Margarita

2013-01-01

The burden of the childhood obesity epidemic is well recognized; nevertheless, the genetic markers and gene-environment interactions associated with the development of common obesity are still unknown. In this study, candidate genes associated to satiety and appetite control pathways with obesity-related traits were tested in Caucasian preschoolers from the STRONG Kids project. Eight genetic variants in genes related to obesity (BDNF, LEPR, FTO, PCSK1, POMC, TUB, LEP, and MC4R) were genotyped in 128 children from the STRONG Kids project (mean age 39.7 months). Data were analyzed for individual associations and to test for genetic predisposition scores (GPSs) with body mass index (BMI) and anthropometric traits (Z-scores, e.g. height-for-age Z-score, HAZ). Covariates included age, sex, and breastfeeding (BF) duration. Obesity and overweight prevalence was 6.3 and 19.5%, respectively, according to age- and sex-specific BMI percentiles. Individual genetic associations of MC4R and LEPR markers with HAZ were strengthened when BF duration was included as a covariate. Our GPSs show that, as the number of risk alleles increased, the risk of higher BMI and HAZ also increased. Overall, the GPSs assembled were able to explain 2-3% of the variability in BMI and HAZ phenotypes. Genetic associations with common obesity-related phenotypes were found in the STRONG Kids project. GPSs assembled for specific candidate genes were associated with BMI and HAZ phenotypes. © 2013 S. Karger AG, Basel.

Helium-induced weld cracking in austenitic and martensitic steels

International Nuclear Information System (INIS)

Lin, H.T.; Chin, B.A.

1991-01-01

Helium was uniformly implanted into type 316 stainless steel and Sandvik HT-9 (12Cr-1MoVW) to levels of 0.18 to 256 and 0.3 to 1 a.p.p.m., respectively, using the ''tritium trick'' technique. Autogenous bead-on-plate, full penetration, welds were then produced under fully constrained conditions using the gas tungsten arc welding (GTAW) process. The control and hydrogen-charged plates of both alloys were sound and free of any weld defects. For the 316 stainless steel, catastrophic intergranular fracture occurred in the heat-affected zone (HAZ) of welds with helium levels ≥ 2.5 a.p.p.m. In addition to the HAZ cracking, brittle fracture along the centreline of the fusion zone was also observed for the welds containing greater than 100 a.p.p.m. He. For HT-9, intergranular cracking occurred in the HAZ along prior-austenite grain boundaries of welds containing 1 a.p.p.m. He. Electron microscopy observations showed that the cracking in the HAZ originated from the growth and coalescence of grain-boundary helium bubbles and that the fusion-zone cracking resulted from the growth of helium bubbles at dendrite boundaries. The bubble growth kinetics in the HAZ is dominated by stress-induced diffusion of vacancies into bubbles. Results of this study indicate that the use of conventional GTAW techniques to repair irradiation-degraded materials containing even small amounts of helium may be difficult. (author)

Evaluation of local deformation behavior accompanying fatigue damage in F82H welded joint specimens by using digital image correlation

International Nuclear Information System (INIS)

Nakata, Toshiya; Tanigawa, Hiroyasu

2012-01-01

Highlights: ► In tensile, the TIG welded joint material was concentrated in the THAZ. ► In tensile, fracture occurred at the point where the axial strain converged. ► In fatigue, fracture occurred at the point where the Max. shear strain converged. ► Many macrocracks and cavities formed in the FGHAZ and THAZ of the cross section. - Abstract: By using digital image correlation, the deformation behaviors of local domains of F82H joint specimens welded using tungsten inert gas (TIG) and electron beam (EB) welding were evaluated during tensile and fatigue testing. In the tensile test specimens, the tensile strength decreased in the TIG-welded joints, and ductility decreased in both the EB- and TIG-welded joints. Because axial strain increased in the tempered heat-affected zone (HAZ) and led to the fracture of the TIG-welded joint, the strength was considered to have decreased because of welding. In fatigue testing, the number of cycles to fracture for the welded joint decreased to less than 40–60% of that for the base metal. For both fracture specimens, the largest value of shear strain was observed in the region approximately between the fine-grained HAZ and tempered HAZ; this shear strain ultimately led to fracture. Cavities and macrocracks were observed in the fine-grained HAZ and tempered HAZ in the cross sections of the fracture specimens, and geometrical damage possibly resulted in the reduction of fatigue lifetime.

Stunting at birth: recognition of early-life linear growth failure in the western highlands of Guatemala.

Science.gov (United States)

Solomons, Noel W; Vossenaar, Marieke; Chomat, Anne-Marie; Doak, Colleen M; Koski, Kristine G; Scott, Marilyn E

2015-07-01

Measurements of length at birth, or in the neonatal period, are challenging to obtain and often discounted for lack of validity. Hence, classical 'under-5' stunting rates have been derived from surveys on children from 6 to 59 months of age. Guatemala has a high prevalence of stunting (49.8%), but the age of onset of growth failure is not clearly defined. The objective of the study was to assess length-for-age within the first 1.5 months of life among Guatemalan infants. As part of a cross-sectional observational study, supine length was measured in young infants. Mothers' height was measured. Length-for-age Z-scores (HAZ) were generated and stunting was defined as HAZ Guatemala. Three hundred and six newborns with a median age of 19 d. The median rural HAZ was -1.56 and prevalence of stunting was 38%; the respective urban values were -1.41 and 25%. Linear regression revealed no relationship between infant age and HAZ (r = 0.101, r(2) = 0.010, P = 0.077). Maternal height explained 3% of the variability in HAZ (r = 0.171, r(2) = 0.029, P = 0.003). Stunting must be carried over from in utero growth retardation in short-stature Guatemalan mothers. As linear growth failure in this setting begins in utero, its prevention must be linked to maternal care strategies during gestation, or even before. A focus on maternal nutrition and health in an intergenerational dimension is needed to reduce its prevalence.

Assessing the effect of drought severity on height-for-age z-score in Kenyan children: a secondary analysis

Directory of Open Access Journals (Sweden)

Kate Lillepold, BScH

2018-05-01

Full Text Available Background: Globally, droughts are occurring more regularly and are having negative effects on population health, particularly in countries such as Kenya, where agriculture is a primary driver of the economy and a source of subsistence for many communities. Children are particularly susceptible to weather-related shocks. Previous research has shown an association between drought and cross-sectional indicators of malnutrition, such as stunting. In this study, we explored various longitudinal and spatial analysis approaches to evaluating the effect of drought on height-for-age z-scores (HAZ over time and space among young children in Kenya. Methods: Using anthropometric data from three georeferenced Kenyan Demographic and Health Surveys (KDHS and the self-calibrated Palmer Drought Severity Index, we developed multivariate linear regression and spatial lag and error models (with Moran's I calculations to investigate the association between drought severity and HAZ in children aged 0–5 years. Initial covariates included age of the child, sex, maternal age, height and education, wealth index, urban or rural location, and size at birth. We then did multilevel and geographically weighted regression modelling using frequentist or Bayesian methods and with inclusion of household-level covariates, such as livelihood zones. To assess the effect of changes in drought severity on child HAZ over time, KDHS data from 2003, 2008–09, and 2014 were analysed with spatiotemporal modelling. Findings: Preliminary results from the multivariate linear model showed a negative, non-significant association between drought severity and HAZ among Kenyan children in 2014 (β=0·033, p=0·101; however, there was a significant interaction between drought severity and age (β=–0·002, p<0·0007. The spatial lag model gave similar results. Other variables associated with HAZ included wealth index, age, sex, maternal education, and maternal height. Global Moran's I

Heat affected zone microfissuring in a laser beam welded directionally solidified Ni3Al-base alloy

International Nuclear Information System (INIS)

Ojo, O.A.; Ding, R.G.; Chaturvedi, M.C.

2006-01-01

The laser beam weld heat affected zone (HAZ) microstructure of a newly developed aerospace alloy, IC 6, was examined. HAZ microfissuring was observed and found to be associated with grain boundary liquation facilitated by subsolidus eutectic-type transformation of the alloy's major phase, γ' precipitates, and interfacial melting of M 6 C-type carbide and (Mo 2 Ni)B 2 -type boride particles

Numerical Simulation of Temperature Field and Residual Stress Distribution for Laser Cladding Remanufacturing

Directory of Open Access Journals (Sweden)

Liang Hua

2014-05-01

Full Text Available A three-dimensional finite element model was employed to simulate the cladding process of Ni-Cr-B-Si coatings on 16MnR steel under different parameters of laser power, scanning speed, and spot diameter. The temperature and residual stress distribution, the depth of the heat affected zone (HAZ, and the optimized parameters for laser cladding remanufacturing technology were obtained. The orthogonal experiment and intuitive analysis on the depth of the HAZ were performed to study the influence of different cladding parameters. A new criterion based on the ratio of the maximum tensile residual stress and fracture strength of the substrate was proposed for optimization of the remanufacturing parameters. The result showed well agreement with that of the HAZ analysis.

Intelligent Modeling Combining Adaptive Neuro Fuzzy Inference System and Genetic Algorithm for Optimizing Welding Process Parameters

Science.gov (United States)

Gowtham, K. N.; Vasudevan, M.; Maduraimuthu, V.; Jayakumar, T.

2011-04-01

Modified 9Cr-1Mo ferritic steel is used as a structural material for steam generator components of power plants. Generally, tungsten inert gas (TIG) welding is preferred for welding of these steels in which the depth of penetration achievable during autogenous welding is limited. Therefore, activated flux TIG (A-TIG) welding, a novel welding technique, has been developed in-house to increase the depth of penetration. In modified 9Cr-1Mo steel joints produced by the A-TIG welding process, weld bead width, depth of penetration, and heat-affected zone (HAZ) width play an important role in determining the mechanical properties as well as the performance of the weld joints during service. To obtain the desired weld bead geometry and HAZ width, it becomes important to set the welding process parameters. In this work, adaptative neuro fuzzy inference system is used to develop independent models correlating the welding process parameters like current, voltage, and torch speed with weld bead shape parameters like depth of penetration, bead width, and HAZ width. Then a genetic algorithm is employed to determine the optimum A-TIG welding process parameters to obtain the desired weld bead shape parameters and HAZ width.

Fracture behaviour of weld joints made of pearlitic and bainitic steel

Directory of Open Access Journals (Sweden)

Libor Válka

2016-06-01

Full Text Available The paper is concerned with microstructure evaluations and the hardness and fracture behaviour of welded joints made from cast bainitic Lo8CrNiMo steel and pearlitic rail steel of the type UIC 900A. The materials mentioned are predetermined for frogs of switches. The study is based mainly on microstructural observations and hardness measurements of the base materials, weld, and heat affected zone (HAZ. Dynamic fracture toughness was evaluated based on data from pre-cracked Charpy type specimens. The pearlitic UIC 900A steel and its HAZ had the lowest dynamic fracture toughness values and therefore the highest risk of brittle fracture. At application temperature range, this steel is on the lower shelf of the ductile-to-brittle transition, and the tempering in the HAZ did not affect the toughness substantially. The cast bainitic steel in the weld joint is characterized by higher toughness values compared to the pearlitic one, and a further increase in toughness may be expected in the HAZ. The weld zone itself is characterized by high scatter of toughness data; nevertheless, all the values are above the scatter band characterizing the pearlitic steel.

Effect of Welding Thermal Cycles on Microstructure and Mechanical Properties of Simulated Heat Affected Zone for a Weldox 1300 Ultra-High Strength Alloy Steel

Directory of Open Access Journals (Sweden)

Węglowski M. St.

2016-03-01

Full Text Available In the present study, the investigation of weldability of ultra-high strength steel has been presented. The thermal simulated samples were used to investigate the effect of welding cooling time t8/5 on microstructure and mechanical properties of heat affected zone (HAZ for a Weldox 1300 ultra-high strength steel. In the frame of these investigation the microstructure was studied by light and transmission electron microscopies. Mechanical properties of parent material were analysed by tensile, impact and hardness tests. In details the influence of cooling time in the range of 2,5 ÷ 300 sec. on hardness, impact toughness and microstructure of simulated HAZ was studied by using welding thermal simulation test. The microstructure of ultra-high strength steel is mainly composed of tempered martensite. The results show that the impact toughness and hardness decrease with increase of t8/5 under condition of a single thermal cycle in simulated HAZ. The increase of cooling time to 300 s causes that the microstructure consists of ferrite and bainite mixture. Lower hardness, for t8/5 ≥ 60 s indicated that low risk of cold cracking in HAZ for longer cooling time, exists.

Maternal nutrition knowledge and child nutritional outcomes in urban Kenya.

Science.gov (United States)

Debela, Bethelhem Legesse; Demmler, Kathrin M; Rischke, Ramona; Qaim, Matin

2017-09-01

We examine the link between maternal nutrition knowledge and nutritional outcomes of children and adolescents (5-18 years) measured in terms of height-for-age Z-scores (HAZ). One particular focus is on the role of different types of nutrition knowledge. The analysis builds on household-level and individual-level data collected in urban Kenya in 2012 and 2015. Various regression models are developed and estimated. Results show that maternal nutrition knowledge - measured through an aggregate knowledge score - is positively associated with child HAZ, even after controlling for other influencing factors such as household living standard and general maternal education. However, disaggregation by type of knowledge reveals important differences. Maternal knowledge about food ingredients only has a weak positive association with child HAZ. For maternal knowledge about specific dietary recommendations, no significant association is detected. The strongest positive association with child HAZ is found for maternal knowledge about the health consequences of not following recommended dietary practices. These findings have direct relevance for nutrition and health policies, especially for designing the contents of educational campaigns and training programs. Copyright © 2017 Elsevier Ltd. All rights reserved.

Metallurgy and mechanical properties variation with heat input,during dissimilar metal welding between stainless and carbon steel

Science.gov (United States)

Ramdan, RD; Koswara, AL; Surasno; Wirawan, R.; Faturohman, F.; Widyanto, B.; Suratman, R.

2018-02-01

The present research focus on the metallurgy and mechanical aspect of dissimilar metal welding.One of the common parameters that significantly contribute to the metallurgical aspect on the metal during welding is heat input. Regarding this point, in the present research, voltage, current and the welding speed has been varied in order to observe the effect of heat input on the metallurgical and mechanical aspect of both welded metals. Welding was conducted by Gas Metal Arc Welding (GMAW) on stainless and carbon steel with filler metal of ER 309. After welding, hardness test (micro-Vickers), tensile test, macro and micro-structure characterization and Energy Dispersive Spectroscopy (EDS) characterization were performed. It was observed no brittle martensite observed at HAZ of carbon steel, whereas sensitization was observed at the HAZ of stainless steel for all heat input variation at the present research. Generally, both HAZ at carbon steel and stainless steel did not affect tensile test result, however the formation of chromium carbide at the grain boundary of HAZ structure (sensitization) of stainless steel, indicate that better process and control of welding is required for dissimilar metal welding, especially to overcome this issue.

High-Power Laser Cutting of Steel Plates: Heat Affected Zone Analysis

Directory of Open Access Journals (Sweden)

Imed Miraoui

2016-01-01

Full Text Available The thermal effect of CO2 high-power laser cutting on cut surface of steel plates is investigated. The effect of the input laser cutting parameters on the melted zone depth (MZ, the heat affected zone depth (HAZ, and the microhardness beneath the cut surface is analyzed. A mathematical model is developed to relate the output process parameters to the input laser cutting parameters. Three input process parameters such as laser beam diameter, cutting speed, and laser power are investigated. Mathematical models for the melted zone and the heat affected zone depth are developed by using design of experiment approach (DOE. The results indicate that the input laser cutting parameters have major effect on melted zone, heat affected zone, and microhardness beneath cut surface. The MZ depth, the HAZ depth, and the microhardness beneath cut surface increase as laser power increases, but they decrease with increasing cutting speed. Laser beam diameter has a negligible effect on HAZ depth but it has a remarkable effect on MZ depth and HAZ microhardness. The melted zone depth and the heat affected zone depth can be reduced by increasing laser cutting speed and decreasing laser power and laser beam diameter.

Evaluation of flow properties in the weldments of vanadium alloys using a novel indentation technique

Energy Technology Data Exchange (ETDEWEB)

Gubbi, A.N.; Rowcliffe, A.F.; Lee, E.H.; King, J.F.; Goodwin, G.M. [Oak Ridge National Lab., TN (United States)

1996-10-01

Automated Ball Indentation (ABI) testing, was successfully employed to determine the flow properties of the fusion zone, heat affected zone (HAZ), and base metal of the gas tungsten arc (GTA) and electron beam (EB) welds of the V-4Cr-4Ti (large heat no. 832665) and the V-5Cr-5Ti (heat 832394) alloys. ABI test results showed a clear distinction among the properties of the fusion zone, HAZ, and base metal in both GTA and EB welds of the two alloys. GTA and EB welds of both V-4Cr-4Ti and V-5Cr-5Ti alloys show strengthening of both the fusion zone and the HAZ (compared to base metal) with the fusion zone having higher strength than the HAZ. These data correlate well with the Brinell hardness. On the other hand, GTA welds of both alloys, after a post-weld heat treatment of 950{degrees}C for 2 h, show a recovery of the properties to base metal values with V-5Cr-5Ti showing a higher degree of recovery compared to V-4Cr-4Ti. These measurements correlate with the reported recovery of the Charpy impact properties.

Analysis of Deformation and Failure Behaviors of TIG Welded Dissimilar Metal Joints Using Miniature Tensile Specimens

Energy Technology Data Exchange (ETDEWEB)

Shin, Ji-Hwan; Jahanzeb, Nabeel; Kim, Min-Seong; Hwang, Ji-Hyun; Choi, Shi-Hoon [Sunchon National University, Suncheon (Korea, Republic of)

2017-02-15

The deformation and failure behaviors of dissimilar metal joints between SS400 steel and STS316L steel were investigated. The dissimilar metal joints were fabricated using the tungsten inert gas (TIG) welding process with STS309 steel as a filler metal. The microstructures of the dissimilar metal joints were investigated using an optical microscope and EBSD technique. The mechanical properties of the base metal (BM), heat affected zone (HAZ) and weld metal (WM) were measured using a micro-hardness and micro-tension tester combined with the digital image correlation (DIC) technique. The HAZ of the STS316L steel exhibited the highest micro-hardness value, and yield/tensile strengths, while the BM of the SS440 steel exhibited the lowest micro-hardness value and yield /tensile strengths. The grain size refinement in the HAZ of SS400 steel induced an enhancement of micro-hardness value and yield/tensile strengths compared to the BM of the SS400 steel. The WM, which consists of primary δ-ferrite and a matrix of austenite phase, exhibited relatively a high micro-hardness value, yield /tensile strengths and elongation compared to the BM and HAZ of the SS400 steel.

Heat input effect on the microstructural transformation and mechanical properties in GTAW welds of a 409L ferritic stainless steel

Energy Technology Data Exchange (ETDEWEB)

Delgado, J. A.; Ambriz, R. R.; Cuenca-Alvarez, R.; Alatorre, N.; Curiel, F. F.

2016-10-01

Welds without filler metal and welds using a conventional austenitic stainless steel filler metal (ER308L) were performed to join a ferritic stainless steel with Gas Tungsten Arc Welding process (GTAW). Welding parameters were adjusted to obtain three different heat input values. Microstructure reveals the presence of coarse ferritic matrix and martensite laths in the Heat Affected Zone (HAZ). Dilution between filler and base metal was correlated with the presence of austenite, martensite and ferrite in the weld metal. Weld thermal cycles were measured to correlate the microstructural transformation in the HAZ. Microhardness measurements (maps and profiles) allow to identify the different zones of the welded joints (weld metal, HAZ, and base metal). Comparing the base metal with the weld metal and the HAZ, a hardness increment (∼172 HV{sub 0}.5 to ∼350 HV{sub 0}.5 and ∼310 HV{sub 0}.5, respectively) was observed, which has been attributed to the martensite formation. Tensile strength of the welded joints without filler metal increased moderately with respect to base metal. In contrast, ductility was approximately 25% higher than base metal, which provided a toughness improvement of the welded joints. (Author)

Metallurgical Effects of Shunting Current on Resistance Spot-Welded Joints of AA2219 Sheets

Science.gov (United States)

Jafari Vardanjani, M.; Araee, A.; Senkara, J.; Jakubowski, J.; Godek, J.

2016-08-01

Shunting effect is the loss of electrical current via the secondary circuit provided due to the existence of previous nugget in a series of welding spots. This phenomenon influences on metallurgical aspects of resistance spot-welded (RSW) joints in terms of quality and performance. In this paper RSW joints of AA2219 sheets with 1 mm thickness are investigated metallurgically for shunted and single spots. An electro-thermal finite element analysis is performed on the RSW process of shunted spot and temperature distribution and variation are obtained. These predictions are then compared with experimental micrographs. Three values of 5 mm, 20 mm, and infinite (i.e., single spot) are assumed for welding distance. Numerical and experimental results are matching each other in terms of nugget and HAZ geometry as increasing distance raised nugget size and symmetry of HAZ. In addition, important effect of shunting current on nugget thickness, microstructure, and Copper segregation on HAZ grain boundaries were discovered. A quantitative analysis is also performed about the influence of welding distance on important properties including ratio of nugget thickness and diameter ( r t), ratio of HAZ area on shunted and free side of nugget ( r HA), and ratio of equivalent segregated and total amount of Copper, measured in sample ( r Cu) on HAZ. Increasing distance from 5 mm to infinite, indicated a gain of 111.04, -45.55, and -75.15% in r t, r HA, and r Cu, respectively, while obtained ratios for 20 mm welding distance was suitable compared to single spot.

Butt Welding of 2205/X65 Bimetallic Sheet and Study on the Inhomogeneity of the Properties of the Welded Joint

Science.gov (United States)

Gou, Ning-Nian; Zhang, Jian-Xun; Wang, Jian-Long; Bi, Zong-Yue

2017-04-01

The explosively welded 2205 duplex stainless steel/X65 pipe steel bimetallic sheets were butt jointed by multilayer and multi-pass welding (gas tungsten arc welding for the flyer and gas metal arc welding for the transition and parent layers of the bimetallic sheets). The microstructure and mechanical properties of the welded joint were investigated. The results showed that in the thickness direction, microstructure and mechanical properties of the welded joint exhibited obvious inhomogeneity. The microstructures of parent filler layers consisted of acicular ferrite, widmanstatten ferrite, and a small amount of blocky ferrite. The microstructure of the transition layer and flyer layer consisted of both austenite and ferrite structures; however, the transition layer of weld had a higher volume fraction of austenite. The results of the microhardness test showed that in both weld metal (WM) and heat-affected zone (HAZ) of the parent filler layers, the average hardness decreased with the increasing (from parent filler layer 1 to parent filler layer 3) welding heat input. The results of hardness test also indicated that the hardness of the WM and the HAZ for the flyer and transition layers was equivalent. The tensile test combined with Digital Specklegram Processing Technology demonstrated that the fracturing of the welded joint started at the HAZ of the flyer, and then the fracture grew toward the base metal of the parent flyer near the parent HAZ. The stratified impact test at -5 °C showed that the WM and HAZ of the flyer exhibited lower impact toughness, and the fracture mode was ductile and brittle mixed fracture.

The effect of prior deformation on stress corrosion cracking growth rates of Alloy 600 materials in a simulated pressurized water reactor primary water

International Nuclear Information System (INIS)

Yamazaki, Seiya; Lu Zhanpeng; Ito, Yuzuru; Takeda, Yoichi; Shoji, Tetsuo

2008-01-01

The effect of prior deformation on stress corrosion cracking (SCC) growth rates of Alloy 600 materials in a simulated pressurized water reactor primary water environment is studied. The prior deformation was introduced by welding procedure or by cold working. Values of Vickers hardness in the Alloy 600 weld heat-affected zone (HAZ) and in the cold worked (CW) Alloy 600 materials are higher than that in the base metal. The significantly hardened area in the HAZ is within a distance of about 2-3 mm away from the fusion line. Electron backscatter diffraction (EPSD) results show significant amounts of plastic strain in the Alloy 600 HAZ and in the cold worked Alloy 600 materials. Stress corrosion cracking growth rate tests were performed in a simulated pressurized water reactor primary water environment. Extensive intergranular stress corrosion cracking (IGSCC) was found in the Alloy 600 HAZ, 8% and 20% CW Alloy 600 specimens. The crack growth rate in the Alloy 600 HAZ is close to that in the 8% CW base metal, which is significantly lower than that in the 20% CW base metal, but much higher than that in the as-received base metal. Mixed intergranular and transgranular SCC was found in the 40% CW Alloy 600 specimen. The crack growth rate in the 40% CW Alloy 600 was lower than that in the 20% CW Alloy 600. The effect of hardening on crack growth rate can be related to the crack tip mechanics, the sub-microstructure (or subdivision of grain) after cross-rolling, and their interactions with the oxidation kinetics

Outcome of anti-retroviral treatment in HIV-infected orphans and non-orphans at an ART centre in North India.

Science.gov (United States)

Bhattacharya, Malobika; Saxena, Romit

2012-01-01

Few Indian studies have reported the long-term efficacy of anti-retroviral treatment (ART) in children and in orphaned, HIV-infected children in particular. To study differences in outcome of ART in HIV-infected orphans compared with non-orphans. A retrospective study of 87 HIV-infected children who commenced ART in the period January 2006 to August 2007. The main measures were orphan status, absolute CD4 count and weight-for-height (WHZ) and height-for-age (HAZ) Z-scores. Median follow-up was 33 months. Forty (45·9%) children were orphaned. Orphans and non-orphans had similar baseline median WHZ and HAZ (-2·48 vs -2·63, P = 0·65 and -2·78 vs -2·91, P = 0·77, respectively). The two groups were similar in terms of WHO clinical stage and frequency of severe immunosuppression at presentation (P = 0·88 and 0·25, respectively). After ART initiation, the median absolute CD4 count increased progressively in both groups. Median WHZ and HAZ increased throughout the study period in the orphans and reached -1 at 27 and 39 months of ART, respectively. In the non-orphans, WHZ remained below that of the orphan group, the difference becoming statistically significant from 18 months of ART. The increment in HAZ in the non-orphan group was at par with the orphan group until 12 months of follow-up, after which it fell between 18 and 30 months. Subsequently, HAZ rose but remained below that of the orphan group. Both WHZ and HAZ failed to reach -1 in the non-orphan group. In both groups, 85% reported 100% adherence to ART. The outcome of ART is not affected by orphan status with the extended family adequately supporting orphaned children. Growth of children whose parents are HIV-infected may be constrained despite ART if there is inadequate family support.

Role of butter layer in low-cycle fatigue behavior of modified 9Cr and CrMoV dissimilar rotor welded joint

International Nuclear Information System (INIS)

Wu, Qingjun; Lu, Fenggui; Cui, Haichao; Liu, Xia; Wang, Peng; Tang, Xinhua

2014-01-01

Highlights: • Modified 9Cr–CrMoV dissimilar turbine rotor was successfully welded by NG-SAW. • LCF properties of both welded joints were approximate at smaller strain amplitude. • Tempered martensite with amounts of carbides in HAZ contributed to weakest zones. • Matched BL determined LCF properties of whole joint for dissimilar welded rotor. - Abstract: The present work aims at studying the role of butter layer (BL) in low-cycle fatigue (LCF) behavior of modified 9Cr steel and CrMoV steel dissimilar welded joint. The significant difference of the chemical composition of base metals (BMs) makes it a challenge to achieve sound welded joint. Therefore, buttering was considered to obtain a transition layer between the dissimilar steels. The LCF tests of two kinds of specimens without and with butter layer were performed applying strain-controlled cyclic load with different axial strain amplitudes. The test results indicated that the number of cycles at higher strain amplitudes of welded joint without butter layer was greatly higher than that of the joint with butter layer, while the fatigue lifetime to crack initiation (2N f ) became closer to each other at low and middle strain amplitudes. The failure was in the tempered heat affected zone (HAZ) at the CrMoV side for specimens without BL, while the fracture occurred at the tempered HAZ in the BL for specimens with BL. The microstructure details of BM, BL, HAZ and weld metals (WMs) were revealed by optical microscopy (OM). It was found that the tempered martensite was major microstructure for welded joint and much more carbides were observed in tempered HAZ than other parts due to the repeated tempering. Microhardness test indicated a softest zone existing tempered HAZ of BL and also there was a softer zone in tempered HAZ at the CrMoV side due to repeated tempering during welding and post weld heat treatment (PWHT). And scanning electron microscopy (SEM) was applied to observe the fractography. It was

Hazard and operability study of Heavy Water Plant, Manuguru

Energy Technology Data Exchange (ETDEWEB)

Nayak, S K; Khilnaney, V K [Heavy Water Board, Department of Atomic Energy, Mumbai (India)

1994-06-01

The chemical process industry faces the tough challenge of achieving design productivity while maintaining high standards of safety. This task is particularly difficult than handling hazardous chemicals. Hazard and operability study (HazOp) is a technique which involves systematic and thorough study by a multidisciplinary team. This technique provides a means to analyse the design and modes of operations of a plant systematically so as to identify the potential occurrence of hazardous events and operational problems. HazOp is based on the premise that a hazard is not realised if the process is operated within its design intent. This paper gives an overall view of the HazOp study carried out at Heavy Water Plant, Manuguru. Some selected recommendations from this study are highlighted. (author). 2 refs., 5 figs.

Analysis of laser beam weldability of Inconel 738 superalloy

International Nuclear Information System (INIS)

Egbewande, A.T.; Buckson, R.A.; Ojo, O.A.

2010-01-01

The susceptibility of pre-weld heat treated laser beam welded IN 738 superalloy to heat affected zone (HAZ) cracking was studied. A pre-weld heat treatment that produced the minimal grain boundary liquation resulted in a higher level of cracking compared to those with more intergranular liquation. This deviation from the general expectation of influence of intergranular liquation extent on HAZ microfissuring is attributable to the reduction in the ability of the base alloy to accommodate welding tensile stress that accompanied a pre-weld heat treatment condition designed to minimize intergranular liquation. Furthermore, in contrast to what has been generally reported in other nickel-based superalloys, a decrease in laser welding speed resulted in increased HAZ cracking in the IN 738, which can be attributed to exacerbated process instability at lower welding speeds.

Knowledge acquisition on hazards in chemical and process industry

International Nuclear Information System (INIS)

Vojnovic, D.; Kozuh, M.

1992-01-01

The knowledge acquisition for probabilistic risk assessment and operational safety improvements are described. The procedure HazOp (Hazard and Operability Study) are used for hazard identification. The acquainted knowledge is condensed in the form of cause-consequence matrix which is very convenient for plant logic model start point definition. At the end, the possibility for HazOp performance support by use of Artificial Intelligence approach is considered. (author) [sl

Early Childhood Diarrhea Predicts Cognitive Delays in Later Childhood Independently of Malnutrition.

Science.gov (United States)

Pinkerton, Relana; Oriá, Reinaldo B; Lima, Aldo A M; Rogawski, Elizabeth T; Oriá, Mônica O B; Patrick, Peter D; Moore, Sean R; Wiseman, Benjamin L; Niehaus, Mark D; Guerrant, Richard L

2016-11-02

Understanding the complex relationship between early childhood infectious diseases, nutritional status, poverty, and cognitive development is significantly hindered by the lack of studies that adequately address confounding between these variables. This study assesses the independent contributions of early childhood diarrhea (ECD) and malnutrition on cognitive impairment in later childhood. A cohort of 131 children from a shantytown community in northeast Brazil was monitored from birth to 24 months for diarrhea and anthropometric status. Cognitive assessments including Test of Nonverbal Intelligence (TONI), coding tasks (WISC-III), and verbal fluency (NEPSY) were completed when children were an average of 8.4 years of age (range = 5.6-12.7 years). Multivariate analysis of variance models were used to assess the individual as well as combined effects of ECD and stunting on later childhood cognitive performance. ECD, height for age (HAZ) at 24 months, and weight for age (WAZ) at 24 months were significant univariate predictors of the studies three cognitive outcomes: TONI, coding, and verbal performance (P < 0.05). Multivariate models showed that ECD remained a significant predictor, after adjusting for the effect of 24 months HAZ and WAZ, for both TONI (HAZ, P = 0.029 and WAZ, P = 0.006) and coding (HAZ, P = 0.025 and WAZ, P = 0.036) scores. WAZ and HAZ were also significant predictors after adjusting for ECD. ECD remained a significant predictor of coding (WISC III) after number of household income was considered (P = 0.006). This study provides evidence that ECD and stunting may have independent effects on children's intellectual function well into later childhood. © The American Society of Tropical Medicine and Hygiene.

Stress Corrosion Cracking Behaviour of Dissimilar Welding of AISI 310S Austenitic Stainless Steel to 2304 Duplex Stainless Steel

Directory of Open Access Journals (Sweden)

Thiago AmaroVicente

2018-03-01

Full Text Available The influence of the weld metal chemistry on the stress corrosion cracking (SCC susceptibility of dissimilar weldments between 310S austenitic stainless steel and 2304 duplex steels was investigated by constant load tests and microstructural examination. Two filler metals (E309L and E2209 were used to produce fusion zones of different chemical compositions. The SCC results showed that the heat affected zone (HAZ on the 2304 base metal side of the weldments was the most susceptible region to SCC for both filler metals tested. The SCC results also showed that the weldments with 2209 duplex steel filler metal presented the best SCC resistance when compared to the weldments with E309L filler metal. The lower SCC resistance of the dissimilar joint with 309L austenitic steel filler metal may be attributed to (1 the presence of brittle chi/sigma phase in the HAZ on the 2304 base metal, which produced SC cracks in this region and (2 the presence of a semi-continuous delta-ferrite network in the fusion zone which favored the nucleation and propagation of SC cracks from the fusion zone to HAZ of the 2304 stainless steel. Thus, the SC cracks from the fusion zone associated with the SC cracks of 2304 HAZ decreased considerably the time-of-fracture on this region, where the fracture occurred. Although the dissimilar weldment with E2209 filler metal also presented SC cracks in the HAZ on the 2304 side, it did not present the delta ferrite network in the fusion zone due to its chemical composition. Fractography analyses showed that the mixed fracture mode was predominant for both filler metals used.

Experimental assessments of notch ductility and tensile strength of stainless steel weldments after 1200C neutron irradiation

International Nuclear Information System (INIS)

Hawthorne, J.R.; Menke, B.H.; Awadalla, N.G.; O'Kula, K.R.

1986-01-01

The Charpy-V (C/sub v/) properties of AISI 300 series stainless steel plate, weld, and weld heat-affected zone (HAZ) materials from commercial production weldments in 406-mm-diameter pipe (12.7-mm wall) were investigated in unirradiated and irradiated conditions. Weld and HAZ tensile properties were also assessed in the two conditions. The plates and weld filler wires represent different steel melts; the welds were produced using the multipass MIG process. Weldment properties in two test orientations were evaluated. Specimens were irradiated in the UBR reactor to 1 x 10 20 n/cm 2 , E >0.1 MeV in a controlled temperature assembly. Specimen tests were performed at 25 0 C and 125 0 C. The radiation-induced reductions in C/sub v/ energy absorption at 25 0 C were about 42 percent for the weld and HAZ materials evaluated. A trend of energy increase with temperature was observed. The concomitant elevation in yield strength was about 53%. In contrast, the increase in tensile strength was only 16%. The postirradiation yield strength of the axial test orientation in the pipe was less than that of the circumferential test orientation. Results for the HAZ indicate that this component may be the weakest link in the weldment from a fracture resistant viewpoint

Intergranular Corrosion Behavior of 304LN Stainless Steel Heat Treated at 623 K (350 °C)

Science.gov (United States)

Singh, Raghuvir; Kumar, Mukesh; Ghosh, Mainak; Das, Gautam; Singh, P. K.; Chattoraj, I.

2013-01-01

Low temperature sensitization of 304LN stainless steel from the two pipes, differing slightly in chemical composition, has been investigated; specimens were aged at 623 K (350 °C) for 20,000 hours and evaluated for intergranular corrosion and degree of sensitization. The base and heat-affected zone (HAZ) of the 304LN-1 appear resistant to sensitization, while 304LN-2 revealed a "dual" type microstructure at the transverse section and HAZ. The microstructure at 5.0-mm distance from the fusion line indicates qualitatively less sensitization as compared to that at 2.0 mm. The 304LN-2 base alloy shows overall lower degree of sensitization values as compared to the 304LN-1. A similar trend of degree of sensitization was observed in the HAZ where it was higher in the 304LN-1 as compared to the 304LN-2. The weld zone of both the stainless steels suffered from cracking during ASTM A262 practice E, while the parent metals and HAZs did not show such fissures. A mottled image within the ferrite lamella showed spinodal decomposition. The practice E test and transmission electron microscopy results indicate that the interdendritic regions may suffer from failure due to carbide precipitation and due to the evolution of brittle phase from spinodal decomposition.

Mechanical properties and microstructure of laser welded Ti–6Al–2Sn–4Zr–2Mo (Ti6242) titanium alloy

Energy Technology Data Exchange (ETDEWEB)

Chamanfar, A., E-mail: ahc215@lehigh.edu [Institute for Metal Forming, Department of Materials Science and Engineering, Lehigh University, 5 East Packer Avenue, Bethlehem, PA 18015 (United States); Pasang, T. [Department of Mechanical Engineering, Auckland University of Technology, Auckland (New Zealand); Ventura, A.; Misiolek, W.Z. [Institute for Metal Forming, Department of Materials Science and Engineering, Lehigh University, 5 East Packer Avenue, Bethlehem, PA 18015 (United States)

2016-04-29

Room temperature tensile properties and microhardness of a laser welded Ti–6Al–2Sn–4Zr–2Mo (Ti6242) titanium alloy sheet were examined and correlated to the microstructure evolution across the weld. Tensile testing integrated with the optical image correlation Instron® system indicated that the average yield strength (YS), ultimate tensile strength (UTS), and total elongation of the weldment were respectively 88%, 87%, and 69% of the corresponding base material (BM) values. Electron probe microanalysis (EPMA) demonstrated a uniform distribution of the main alloying elements across the weld. The hardness raised increasingly from the BM toward the heat affected zone (HAZ) and the fusion zone (FZ) due to mainly a higher α volume fraction in HAZ and acicular α′ martensite formation in the FZ. Because of the higher hardness of the HAZ and FZ, a higher YS for the weldment relative to the BM would be expected. However, the lower YS as well as the lower UTS of the weldment can be explained by presence of some porosity and underfill in the FZ. The lower total elongation of the weldment compared to the BM can be related to the higher hardness of the HAZ and FZ.

Failure of Stainless Steel Welds Due to Microstructural Damage Prevented by In Situ Metallography

Directory of Open Access Journals (Sweden)

Juan Manuel Salgado Lopez

Full Text Available Abstract In stainless steels, microstructural damage is caused by precipitation of chromium carbides or sigma phase. These microconstituents are detrimental in stainless steel welds because they lead to weld decay. Nevertheless, they are prone to appear in the heat affected zone (HAZ microstructure of stainless steel welds. This is particularly important for repairs of industrial components made of austenitic stainless steel. Non-destructive metallography can be applied in welding repairs of AISI 304 stainless steel components where it is difficult to ensure that no detrimental phase is present in the HAZ microstructure. The need of microstructural inspection in repairs of AISI 304 is caused because it is not possible to manufacture coupons for destructive metallography, with which the microstructure can be analyzed. In this work, it is proposed to apply in situ metallography as non-destructive testing in order to identify microstructural damage in the microstructure of AISI 304 stainless steel welds. The results of this study showed that the external surface micrographs of the weldment are representative of HAZ microstructure of the stainless steel component; because they show the presence of precipitated metallic carbides in the grain boundaries or sigma phase in the microstructure of the HAZ.

Mechanisms of stress relief cracking in titanium stabilised austenitic stainless steel

International Nuclear Information System (INIS)

Chabaud-Reytier, M.; Allais, L.; Caes, C.; Dubuisson, P.; Pineau, A.

2003-01-01

The heat affected zone (HAZ) of AISI 321 welds may exhibit a serious form of cracking during service at high temperature. This form of damage, called 'stress relief cracking', is known to be due to work hardening but also to aging due to Ti(C,N) precipitation on dislocations which modifies the mechanical behaviour of the HAZ. The present study aims to analyse the latter embrittlement mechanism in one specific heat of 321 stainless steel. To this end, different HAZs are simulated using an annealing heat-treatment, followed by various cold rolling and aging conditions. Then, we study the effects of work hardening and aging on Ti(C,N) precipitation, on the mechanical (hardness, tensile and creep) behaviour of the simulated HAZs and on their sensitivity to intergranular crack propagation through stress relaxation tests performed on pre-cracked CT type specimens tested at 600 deg. C. It is shown that work hardening is the main parameter of the involved mechanism but that aging does not promote crack initiation although it leads to titanium carbide precipitation. Therefore, the role of Ti(C,N) precipitation on stress relief cracking mechanisms is discussed. An attempt is made to show that solute drag effects are mainly responsible for this form of intergranular damage, rather than Ti(C,N) precipitation

Development of High Heat Input Welding Offshore Steel as Normalized Condition

Science.gov (United States)

Deng, Wei; Qin, Xiaomei

The heavy plate used for offshore structure is one of the important strategic products. In recent years, there is an increasing demand for heavy shipbuilding steel plate with excellent weldability in high heat input welding. During the thermal cycle, the microstructure of the heat affected zone (HAZ) of plates was damaged, and this markedly reduced toughness of HAZ. So, how to improve the toughness of HAZ has been a key subject in the fields of steel research. Oxide metallurgy is considered as an effective way to improve toughness of HAZ, because it could be used to retard grain growth by fine particles, which are stable at the high temperature.The high strength steel plate, which satisfies the low temperature specification, has been applied to offshore structure. Excellent properties of the plates and welded joints were obtained by oxide metallurgy technology, latest controlled rolling and accelerated cooling technology using Ultra-Fast Cooling (an on-line accelerated cooling system). The 355MPa-grade high strength steel plates with normalizing condition were obtained, and the steels have excellent weldability with heat input energy of 79 287kJ/cm, and the nil ductility transition (NDT) temperature was -70°C, which can satisfy the construction of offshore structure in cold regions.

Effects of absorbed hydrogen on crack-tip ductility in the welded A516 steel

International Nuclear Information System (INIS)

Khattak, M.A.; Haslan, M.H.; Tamin, M.N.

2007-01-01

Effects of absorbed hydrogen on structure and properties of welded A516 Grade-70 steel are investigated. Emphasis is placed on ductility measure of the crack-tip plastic zone under Mode I loading. Specimens are cathodically charged in a cell with dilute sulphuric acid and corrosion inhibitor with uniform charging current density of 20 mA/ cm 2 and at different exposure time. Results indicate a change from coarse- to fine-grained microstructures in the weld region and heat affected zone (HAZ) of hydrogen-charged specimen. Well-defined ferrite-pearlite bands in the base metal are transformed into coarse-grain structure. Hardness variation along radial distance indicates higher values towards the center of the bar, possibly due to faster diffusion rate but limited solubility of hydrogen. Load-COD responses indicate that slow, stable crack propagation occurred in both base metal and HAZ. The measured provisional fracture toughness, K Q is higher for HAZ than that for the base metal. The toughness values decreases significantly for the initial three hours of hydrogen charging. The tensile fracture region in the immediate fatigue pre-crack tip forms a triangular (rough) zone due to limited constraint to free surface deformation in the thin specimen. Fracture surface of HAZ is dominated by intergranular fracture with localized cleavage facets. (author)

Mechanical properties and microstructure of laser welded Ti–6Al–2Sn–4Zr–2Mo (Ti6242) titanium alloy

International Nuclear Information System (INIS)

Chamanfar, A.; Pasang, T.; Ventura, A.; Misiolek, W.Z.

2016-01-01

Room temperature tensile properties and microhardness of a laser welded Ti–6Al–2Sn–4Zr–2Mo (Ti6242) titanium alloy sheet were examined and correlated to the microstructure evolution across the weld. Tensile testing integrated with the optical image correlation Instron® system indicated that the average yield strength (YS), ultimate tensile strength (UTS), and total elongation of the weldment were respectively 88%, 87%, and 69% of the corresponding base material (BM) values. Electron probe microanalysis (EPMA) demonstrated a uniform distribution of the main alloying elements across the weld. The hardness raised increasingly from the BM toward the heat affected zone (HAZ) and the fusion zone (FZ) due to mainly a higher α volume fraction in HAZ and acicular α′ martensite formation in the FZ. Because of the higher hardness of the HAZ and FZ, a higher YS for the weldment relative to the BM would be expected. However, the lower YS as well as the lower UTS of the weldment can be explained by presence of some porosity and underfill in the FZ. The lower total elongation of the weldment compared to the BM can be related to the higher hardness of the HAZ and FZ.

Combination of a Nd:YAG laser and a liquid cooling device to (Zr53Cu30Ni9Al8)Si0.5 bulk metallic glass welding

International Nuclear Information System (INIS)

Wang, H.S.; Chen, H.G.; Jang, J.S.C.; Chiou, M.S.

2010-01-01

Research highlights: → A liquid cooling device (LCD) helps to produce a lower initial welding temperature. → A lower initial welding temperature leads to a faster welding thermal cycle (WTC). → A faster WTC produces a crystallization free weld for a laser welded Zr-based BMG. - Abstract: Using pre-selected welding parameters, a crystallization-free weld for (Zr 53 Cu 30 Ni 9 Al 8 )Si 0.5 bulk metallic glass (BMG) was successfully produced by adopting a Nd:YAG pulse laser in combination with a liquid cooling device (LCD). When a LCD was employed, a faster cooling rate and shorter retention time for the crystallization temperature interval were produced, thus, no crystallization was observed in the weld fusion zone (WFZ) or heat affected zone (HAZ). The hardness in those areas did not differ significantly in comparison to the parent material (PM). For the room temperature laser weld (LCD was not employed), HAZ crystallization seemed unavoidable, although no crystallization occurred within the WFZ. The major crystalline phase in the HAZ was identified as Zr 2 Cu. When the precipitates were greater in the crystallized area (i.e., HAZ), cracks were more likely to form, thus, hardness in the area was decreased.

TÜRK HAZIR GİYİM SANAYİNDE M. PORTER'IN JENERİK STRATEJİLERİNİN KULLANIMI VE FİRMALAR İÇİN STRATEJİ ÖNERİLERİ

OpenAIRE

AKÇAGÜN, Engin; DAL, Vedat

2014-01-01

Bu çalışmanın amacı başarılı hazır giyim firmalarında M. Porter’ın jenerik stratejilerinin kullanımını analiz etmek ve Türk hazır giyim firmalarının uluslararası pazarlarda üstünlük sağlanmaları için strateji önerileri geliştirmektir. Bu amaç doğrultusunda veri toplamak için literatürdeki kaynaklar yoluyla bir anket geliştirilmiştir ve İstanbul Sanayi Odası tarafından her yıl belirlenen İlk ve İkinci 500 Büyük Sanayi Kuruluşu listesinde bulunan hazır giyim firmalarının rekabet stratejileri an...

Corrosion of carbon and low-alloy steel weldments in brines: A literature review: Salt Repository Project

International Nuclear Information System (INIS)

Reimus, P.W.

1988-07-01

The literature indicates that corrosion of carbon and low-alloy steel weldments in brines should not be a major concern if the weld is properly designed and fabricated. Seven characteristics of a weld can affect the corrosion performance of the weldment including composition of the weld metal (with respect to that of the parent metal); microstructure of the weld metal, heat-affected zone (HAZ), and parent metal; size and number of defects (cracks and pores) in the weld metal and HAZ (both internal and external); size, shape composition, location, and number of nonmetallic inclusions in the weld metal and HAZ; residual stress distribution in the weld; hydrogen content of the weld; and geometry of the weld at the outer surface. The effects of these characteristics on weldment corrosion are discussed in the report. 104 refs., 14 figs

Structure and development of cortical bundles in Couroupita guianensis Aubl. (Lecythidaceae)

OpenAIRE

Rajput, Kishore Shankarsinh; Patil, Vidya Shivram

2016-01-01

Estructura y desarrollo de haces corticales en Couroupita guianensis Aubl. (Lecythidaceae) El desarrollo de haces corticales, en ramas y pedúnculos de Couroupita guianensis (Lecythidaceae), comienza cerca del meristemo apical concomitante con los haces vasculares normales. Cada haz cortical llega a estar rodeado por una vaina de fibras que, a menudo, mostraba la presencia de una capa gelatinosa (fibras G). A medida que avanza el crecimiento, cada haz se puede dividir en d...

Microstructural Evolution and Mechanical Properties of Simulated Heat-Affected Zones in Cast Precipitation-Hardened Stainless Steels 17-4 and 13-8+Mo

Science.gov (United States)

Hamlin, Robert J.; DuPont, John N.

2017-01-01

Cast precipitation-hardened (PH) stainless steels 17-4 and 13-8+Mo are used in applications that require a combination of high strength and moderate corrosion resistance. Many such applications require fabrication and/or casting repair by fusion welding. The purpose of this work is to develop an understanding of microstructural evolution and resultant mechanical properties of these materials when subjected to weld thermal cycles. Samples of each material were subjected to heat-affected zone (HAZ) thermal cycles in the solution-treated and aged condition (S-A-W condition) and solution-treated condition with a postweld thermal cycle age (S-W-A condition). Dilatometry was used to establish the onset of various phase transformation temperatures. Light optical microscopy (LOM), scanning electron microscopy (SEM), and energy dispersive spectrometry (EDS) were used to characterize the microstructures, and comparisons were made to gas metal arc welds that were heat treated in the same conditions. Tensile testing was also performed. MatCalc thermodynamic and kinetic modeling software was used to predict the evolution of copper (Cu)-rich body center cubic precipitates in 17-4 and β-NiAl precipitates in 13-8+Mo. The yield strength was lower in the simulated HAZ samples of both materials prepared in the S-A-W condition when compared to their respective base metals. Samples prepared in the S-W-A condition had higher and more uniform yield strengths for both materials. Significant changes were observed in the matrix microstructure of various HAZ regions depending on the peak temperature, and these microstructural changes were interpreted with the aid of dilatometry results, LOM, SEM, and EDS. Despite these significant changes to the matrix microstructure, the changes in mechanical properties appear to be governed primarily by the precipitation behavior. The decrease in strength in the HAZ samples prepared in the S-A-W condition was attributed to the dissolution of precipitates

Results from Project on Enhancement of Aging Management and Maintenance in Nuclear Power Plants - Irradiation Embrittlement of RPV Steels -

International Nuclear Information System (INIS)

Abe, Hiroaki; Onizawa, Kunio; Katsuyama, Jinya; Murakami, Kenta; Iwai, Takeo; Iwata, Tadao; Katano, Yoshio; Sekimura, Naoto; Nagai, Yasuyoshi; Toyama, Takeshi; Tamura, Satoshi

2012-01-01

As one of the NISA Project on Enhancement of Aging Management and Maintenance in Nuclear Power Plants, we have performed research on the irradiation embrittlement of reactor pressure vessel (RPV) steels, especially focusing on irradiation embrittlement on heat affected zone (HAZ) and on applications of ion beams to deduce fundamental insights irradiation-induced embrittlement. The results obtained from the project are summarized as follows. In order to obtain the technical basis to judge the necessity of surveillance specimens from HAZ, the neutron irradiation program was performed at JRR-3, JAEA. The samples were carefully designed based on the insights from finite element analysis, metallography, 3D atom probe and positron annihilation methods, and were fabricated so as to simulate both heat treatment history and microstructure for typical HAZ from as-fabricated RPV steels which also have variation of impurity levels. The fracture toughness of the unirradiated HAZ specimens was equivalent to or better than that of base metals. Irradiation embrittlement and hardening were roughly identical to those of base metals, while some of the fine-grained HAZ microstructure was susceptible to it. The probabilistic fracture mechanics analysis was applied to the structural integrity assessment taking into account the heterogeneous microstructure as well as susceptibility for irradiation embrittlement of each HAZ microstructure under the variation of welding parameter and PTS condition. It was shown that crack propagation at the fine-grained HAZ, but the discontinuous distribution of the microstructure retards the further propagation. For the precise correlation of irradiation embrittlement of RPV steels for the long term operations, accumulations of high-dose data are required. Ion beam irradiation is one of the solutions for the regime and for mechanism-based descriptions. Another interest of ours was to describe irradiation hardening and embrittlement in terms of

Weldability and Strength Recovery of NUCu-140 Advanced Naval Steel

Science.gov (United States)

Bono, Jason T.

NUCu-140 is a ferritic copper-precipitation strengthened steel that is a candidate material for use in many naval and structural applications. Previous work has shown that the heat-affected zone (HAZ) and fusion zone (FZ) of NUCu-140 exhibit softening that is due to dissolution of the copper-rich precipitates. This study aims to recover the FZ and HAZ strength by re-precipitation of the copper-rich precipitates through either multiple weld passes or an isothermal post-weld heat treatment (PWHT). The potential use of multiple thermal cycles was investigated with HAZ simulations using a Gleeble thermomechanical simulator. The HAZ simulations represented two weld thermal cycles with different combinations of peak temperatures during the initial and secondary weld passes. To investigate the potential for a PWHT for strength recovery, gas tungsten arc weld (GTAW) samples were isothermally heated for various times and temperatures. Microhardness measurements revealed no strength recovery in the multipass HAZ samples. The time dependent precipitate characteristics were modeled under the HAZ thermal cycle conditions, and the results showed that the lack of strength recovery could be attributed to insufficient time for re-precipitation during the secondary weld pass. Conversely, full strength recovery in the HAZ was observed in the isothermally heat treated samples. Atom-probe tomography (APT) analysis correlated this strength recovery to re-precipitation of the copper-rich precipitates during the isothermal PWHT. The experimental naval steel known as NUCu-140 and an established naval steel HSLA-100 were subjected to stress-relief cracking (SRC) and hot-ductility testing to assess their relative cracking susceptibilities during the welding process and post weld heat treatment. NUCu-140 exhibited a longer time-to-failure (TTF) and a lower temperature of minimum TTF during SRC testing when compared to HSLA-100, indicating better resistance to SRC for the NUCu-140 steel. The

Carbon Equivalence and Weldability of Microalloyed Steels

Science.gov (United States)

1989-10-25

being considered for Navy applications. Wilson et al [181 in their review of copper-adde. steels have shown that in the CCT diagram for modified versions...almost linearly with austenite grain size (Fig. 4.2) [211. Therefore, the net effect of the addition of micro-alloying elements is to shift the CCT ... diagram to shorter times and thereby decrease the amount of martensite in the HAZ. Recently, computation of austenite grain growth in the HAZ’s of micro

Hot Ductility Behaviors in the Weld Heat-Affected Zone of Nitrogen-Alloyed Fe-18Cr-10Mn Austenitic Stainless Steels

Science.gov (United States)

Moon, Joonoh; Lee, Tae-Ho; Hong, Hyun-Uk

2015-04-01

Hot ductility behaviors in the weld heat-affected zone (HAZ) of nitrogen-alloyed Fe-18Cr-10Mn austenitic stainless steels with different nitrogen contents were evaluated through hot tension tests using Gleeble simulator. The results of Gleeble simulations indicated that hot ductility in the HAZs deteriorated due to the formation of δ-ferrite and intergranular Cr2N particles. In addition, the amount of hot ductility degradation was strongly affected by the fraction of δ-ferrite.

Effects of heat treatment condition on the mechanical properties and weldability of 10Cr-1Mo-VNbN cast steel

International Nuclear Information System (INIS)

Shon, Dae Young; Bang, Kook Soo; Lee, Kyong Woon; Chi, Byung Ha

2003-01-01

Mechanical properties and weldability such as HAZ hardness, cold cracking susceptibility and hot ductility of two differently heat treated 10Cr-1Mo-VNbN cast steels were measured and compared. Because of high hardenability of the cast steel, as-annealed cast steel showed martensitic microstructure and thus had higher hardness than annealed-normalized-tempered cast steel which had tempered martensite. Because the welding electrode used resulted in a high hardness weld metal, both cast steels showed same weld metal cold cracking susceptibility even though the as-annealed cast steel had higher HAZ hardness than the annealed-normalized-tempered cast steel. Both cast steels had excellent hot ductility in high temperature range, indicating no risk of grain boundary liquation cracking in the HAZ. However, the as-annealed cast steel showed an inferior ductility in the intermediate temperature range of 1000∼1150 .deg. C because of larger unrecrystallized grain size

Study of local-zone microstructure, strength and fracture toughness of hybrid laser-metal-inert-gas-welded A7N01 aluminum alloy joint

Energy Technology Data Exchange (ETDEWEB)

Wang, Xiaomin, E-mail: xmwang991011@163.com [School of Life Science and Engineering, Southwest Jiaotong University, Chengdu 610031, Sichuan (China); Li, Bo [School of Materials Science and Engineering, Southwest Jiaotong University, Chengdu 610031, Sichuan (China); Li, Mingxing; Huang, Cui [School of Life Science and Engineering, Southwest Jiaotong University, Chengdu 610031, Sichuan (China); Chen, Hui [School of Materials Science and Engineering, Southwest Jiaotong University, Chengdu 610031, Sichuan (China)

2017-03-14

Mechanical properties of hybrid laser-metal-inert-gas-welded A7N01-T5 aluminum alloy joints were studied by using local samples that were extracted from the base metal (BM), heat-affected zone (HAZ), and fusion zone (FZ) of the joint to investigate the triangular relationship of microstructure, strength and fracture toughness of the local zones. The BM had the highest yield strength, ultimate tensile strength (UTS) and lowest elongation, which contrasts with the FZ. The yield strength of the HAZ is lower than that of the BM, whereas its UTS is very close to that of the BM, and its elongation is higher than that of the BM. The fracture toughness of the three local zones decreased as HAZ>BM>FZ. To analyze differences in local mechanical behavior, the detailed microstructure of the three local zones was studied by optical microscopy and electron backscattered diffraction, whereas the fracture surface and precipitation were studied by scanning and transmission electron microscopy. The variation of grain size, especially the morphology and distribution of strengthening phase in HAZ in welding process is the key factor that leads to its different mechanical properties from that of BM, which can be elucidated by different dislocation mechanism, sheared mechanism or Orowan mechanism. The as-cast microstructure and second-phase particles that segregate between dendritic branches provide the FZ with the lowest yield strength and UTS. The factors including area fraction of the precipitates, the difference of strength between the matrix and the grain boundaries, the precipitate-free zone along grain boundaries, as well as the grain boundaries angle are taken into account to explain the difference of fracture toughness among BM, HAZ and FZ, and their fracture modes.

Strength Evaluation of Heat Affected Zone in Electron Beam Welded ARAA for HCCR TBM in ITER

Energy Technology Data Exchange (ETDEWEB)

Yoon, J. S.; Kim, S. K.; Jin, H. G.; Lee, E. H.; Lee, D. W. [KAERI, Daejeon (Korea, Republic of); Cho, S. [National Fusion Research Institute, Daejeon (Korea, Republic of)

2015-05-15

The Korean helium cooled ceramic reflector (HCCR) test blanket module (TBM) has been developed for ITER, and Korean reduced activation ferritic martensitic (RAFM) steel, called advanced reduced activation alloy (ARAA), has also been developed for a structural material of the HCCR TBM. One case of limited optimized electron beam (EB) welding conditions was selected based on previous work, and the weldability of an EB weld was evaluated for TBM fabrication. The micro-hardness was measured from the base to the weld region, and the microstructures were also observed. A small punch (SP) test considering the HAZ was carried out at room and high (550 .deg. C) temperatures. The empirical mechanical properties of HAZ in the EB weld were evaluated, and the fracture behavior was investigated after the SP test. The SP results show that the estimated yield and tensile strength of the HAZ were higher than the base metal at both temperatures. Korean RAFM steel, ARAA, was developed as a TBM structural material. Using one of the program alloys in ARAA (F206), one case of a limited optimized EB welding condition was selected based on previous works, and the weldability of an EB weld using the SP test was evaluated for TBM fabrication at room and high (550 .deg. C) temperatures. From a micro-Vickers hardness evaluation, the HAZ gave the highest values compared with the other regions. The irregular grain boundaries in the HAZ were observed, but its width was narrower than the TIG weld from the previous results. The optimized welding methods such as the TIG, EB, and laser weld, and the welding procedure considering the PWHT are being established, and the weldability evaluation is also progressing according to the development of the ARAA for the fusion material application in Korea.

Non-destructive Residual Stress Analysis Around The Weld-Joint of Fuel Cladding Materials of ZrNbMoGe Alloys

Directory of Open Access Journals (Sweden)

Parikin

2003-08-01

Full Text Available The residual stress measurements around weld-joint of ZrNbMoGe alloy have been carried out by using X-ray diffraction technique in PTBIN-BATAN. The research was performed to investigate the structure of a cladding material with high temperature corrosion resistance and good weldability. The equivalent composition of the specimens (in %wt. was 97.5%Zr1%Nb1%Mo½%Ge. Welding was carried out by using TIG (tungsten inert gas technique that completed butt-joint with a current 20 amperes. Three region tests were taken in specimen while diffraction scanning, While diffraction scanning, tests were performed on three regions, i.e., the weldcore, the heat-affected zone (HAZ and the base metal. The reference region was determined at the base metal to be compared with other regions of the specimen, in obtaining refinement structure parameters. Base metal, HAZ and weldcore were diffracted by X-ray, and lattice strain changes were calculated by using Rietveld analysis program. The results show that while the quantity of minor phases tend to increase in the direction from the base metal to the HAZ and to the weldcore, the quantity of the ZrGe phase in the HAZ is less than the quantity of the ZrMo2 phase due to tGe element evaporation. The residual stress behavior in the material shows that minor phases, i.e., Zr3Ge and ZrMo2, are more dominant than the Zr matrix. The Zr3Ge and ZrMo2 experienced sharp straining, while the Zr phase was weak-lined from HAZ to weldcore. The hydrostatic residual stress ( in around weld-joint of ZrNbMoGe alloy is compressive stress which has minimum value at about -2.73 GPa in weldcore region

Characterization of laser welds in Al-10 wt.%Si coated ferritic stainless steel

International Nuclear Information System (INIS)

Kong, Jong Pan; Park, Tae Jun; Kim, Jeong Kil; Uhm, Sang Ho; Woo, In Su; Lee, Jong Sub; Park, Bong Gyu; Kang, Chung Yun

2011-01-01

409L stainless steel hot-dipped with Al-10 wt.%Si was welded using CO 2 laser and the microstructure and hardness of the weld were investigated. When the specimen was welded with laser power of 5 kW and welding speed of 5 m/min, full-penetrated sound weld was obtained. With that specimen, the relationship between the microstructure and hardness of the weld was examined. The hardness of the weld was the highest in the fusion zone (FZ) and decreased to the base metal (BM) via heat affected zone (HAZ). The hardness of the HAZ near bond line was also higher than that near the base metal. The maximum hardness in the fusion zone could be explained by the existence of the precipitates, that is, TiN, Ti(C,N), Al 2 O 3 and Al 2 O 3 + TiN mixed compounds with the size of 500 nm, and solution strengthening due to the elements Al and Si dissolved from the coating layer to the fusion zone. There were subgrains within the HAZ and more in the area near the bond line. In addition, fine TiC particles with the size under 50 nm was precipitated in the sub-grain boundaries. The formation of sub-grain boundaries and the particles precipitated in the boundaries might contributed to the high hardness in the HAZ.

Effect of silicon contents on the microstructures and mechanical properties of heat affected zones for 9Cr2WVTa steels

Energy Technology Data Exchange (ETDEWEB)

Wang, Jian [Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Science, 110016, Shenyang (China); Key Laboratory of Nuclear Materials and Safety Assessment, Institute of Metal Research, Chinese Academy of Science, 110016, Shenyang (China); Lu, Shanping, E-mail: shplu@imr.ac.cn [Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Science, 110016, Shenyang (China); Rong, Lijian [Key Laboratory of Nuclear Materials and Safety Assessment, Institute of Metal Research, Chinese Academy of Science, 110016, Shenyang (China); Li, Dianzhong [Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Science, 110016, Shenyang (China)

2016-03-15

The weldability of 9Cr2WVTa steels with silicon content varying from 0.30 wt.% to 1.36 wt.% was studied to meet the requirement of Generation-Ⅳ nuclear reactor. Samples of enlarged HAZs were fabricated by a thermal-mechanical simulator based on the simulation and measurement of non-equilibrium phase transformation. The content of δ-ferrite in the HAZs increased with the silicon content and the peak temperature of welding thermal cycle. The impact toughness in the HAZs decreased in different degrees when the δ-ferrite exhibits stripe (lower than 4.82%) or blocky types (higher than 4.82%). Post weld heat treatment (PWHT) has a significant role on improving the toughness. Adding silicon content increased the volume of δ-ferrite and therefore, decreased the tensile strength of the HAZs for 9Cr2WVTa steels. Silicon also as solid solution strengthening element increased the tensile strength. The 9Cr2WVTa steel has good weldability when the silicon content is lower than 0.60 wt.%. - Highlights: • The weldability of 9Cr2WVTa steel with different silicon contents was studied. • The impact toughness decreased in different degrees owing to the δ-ferrite. • PWHT has a significant role on improving the impact toughness. • The 9Cr2WVTa steel with silicon content not exceeding 0.60 wt.% has good weldability.

Primary water stress corrosion cracking resistance of alloy 690 heat affected zones of butt welds

International Nuclear Information System (INIS)

Fournier, L.; Calonne, O.; Toloczko, M.B.; Bruemmer, S.M.; Massoud, J.P.; Lemaire, E.; Gerard, R.; Somville, F.; Richnau, A.; Lagerstrom, J.

2015-01-01

A wide V-groove butt weld was fabricated from Alloy 690 plates using Alloy 152 filler material, maximum allowable heat input, and very stiff strong-backs. Alloy 690 heat affected zones (HAZ) was characterized in terms of microstructure and plastic strains induced by weld shrinkage. Crack initiation tests were carried out in pure hydrogenated steam at 400 C. degrees for 4000 h. Crack growth rate tests were performed in simulated PWR primary water at a temperature of 360 C. degrees. A maximum plastic strain around 5% was measured in the vicinity of the fusion line, which decreased almost linearly with the distance from the fusion line. Crack initiation tests on Alloy 690 HAZ specimens as well as on 30% cold-rolled Alloy 690 specimens were performed in pure hydrogenated steam at 400 C. degrees (partial pressure of hydrogen = 0.7 bar) for a total of 4000 h using cylindrical notched tensile specimens, reverse U-bends and flat micro-tensile specimens. No crack initiation was detected. Stress corrosion propagation rates revealed extremely low SCC (Stress Corrosion Cracking) growth rates both in the base metal and in the HAZ region whose magnitudes are of no engineering significance. Overall, the results indicated limited plastic strain induced by weld shrinkage in butt weld HAZ, and to no particular susceptibility of primary water stress corrosion cracking. (authors)

Experimental assessments of notch ductility and tensile strength of stainless steel weldments after 1200C neutron irradiation

International Nuclear Information System (INIS)

Hawthorne, J.R.; Menke, B.H.; Awadalla, N.G.; O'Kula, K.R.

1987-01-01

The Charpy-V (C/sub V/) properties of American Iron and Steel Institute (AISI) 300 series stainless steel plate, weld, and weld heat-affected zone (HAZ) materials from commercial production weldments in 406-mm-diameter pipe (12.7-mm wall) were investigated in unirradiated and irradiated conditions. Weld and HAZ tensile properties were also assessed in the two conditions. The plates and weld filler wires represent different steel melts; the welds were produced using the multipass metal inert gas (MIG) process. Weldment properties in two test orientations were evaluated. Specimens were irradiated in a light water cooled and moderated reactor to 1 x 10/sup 20/ n/cm/sup 2/, E > 0.1 MeV, using a controlled temperature assembly. Specimen tests were performed at 25 and 125 0 C. The radiation-induced reductions in C/sub V/ energy absorption at 25 0 C were about 42% for the weld and the HAZ materials evaluated. A trend of energy increase with temperature was observed. The concomitant elevation in yield strength was about 53%. The increase in tensile strength in contrast was only 16%. The postirradiation yield strength of the axial test orientation in the pipe was less than that of the circumferential test orientation. Results for the HAZ indicate that this component may be the weakest link in the weldment from a fracture resistance viewpoint

Effects of a laser surface processing induced heat-affected zone on the fatigue behavior of AISI 4340 steel

International Nuclear Information System (INIS)

McDaniels, R.L.; White, S.A.; Liaw, K.; Chen, L.; McCay, M.H.; Liaw, P.K.

2008-01-01

The effects of the heat-affected zone (HAZ) in AISI 4340 steel created by laser-surface alloying (LSA) on high-cycle fatigue behavior have been investigated. This research was performed by producing several lots of laser-processed AISI 4340 steel using different laser processing parameters, and then subjecting the samples to high-cycle fatigue and Knoop microindentation hardness studies. Samples of tested material from each lot were examined using scanning-electron microscopy (SEM) in order to establish the effects of laser processing on the microstructure of the fatigue-tested AISI 4340 steel. When these three techniques, microindentation hardness testing, high-cycle fatigue testing, and SEM, are combined, a mechanistic understanding of the effect of the HAZ on the fatigue behavior of this alloy might be gained. It was found that the HAZ did not appear to have an adverse effect on the high-cycle fatigue behavior of LSA-processed AISI 4340 steel

Stripe-PZT Sensor-Based Baseline-Free Crack Diagnosis in a Structure with a Welded Stiffener

Directory of Open Access Journals (Sweden)

Yun-Kyu An

2016-09-01

Full Text Available This paper proposes a stripe-PZT sensor-based baseline-free crack diagnosis technique in the heat affected zone (HAZ of a structure with a welded stiffener. The proposed technique enables one to identify and localize a crack in the HAZ using only current data measured using a stripe-PZT sensor. The use of the stripe-PZT sensor makes it possible to significantly improve the applicability to real structures and minimize man-made errors associated with the installation process by embedding multiple piezoelectric sensors onto a printed circuit board. Moreover, a new frequency-wavenumber analysis-based baseline-free crack diagnosis algorithm minimizes false alarms caused by environmental variations by avoiding simple comparison with the baseline data accumulated from the pristine condition of a target structure. The proposed technique is numerically as well as experimentally validated using a plate-like structure with a welded stiffener, reveling that it successfully identifies and localizes a crack in HAZ.

Normalizing effect on fatigue crack propagation at the heat-affected zone of AISI 4140 steel shielded metal arc weldings

Directory of Open Access Journals (Sweden)

B. Vargas-Arista

2013-01-01

Full Text Available The fractography and mechanical behaviour of fatigue crack propagation in the heat-affected zone (HAZ of AISI 4140 steel welded using the shielded metal arc process was analysed. Different austenitic grain size was obtained by normalizing performed at 1200 °C for 5 and 10 hours after welding. Three point bending fatigue tests on pre-cracked specimens along the HAZ revealed that coarse grains promoted an increase in fatigue crack growth rate, hence causing a reduction in both fracture toughness and critical crack length, and a transgranular brittle final fracture with an area fraction of dimple zones connecting cleavage facets. A fractographic analysis proved that as the normalizing time increased the crack length decreased. The increase in the river patterns on the fatigue crack propagation in zone II was also evidenced and final brittle fracture because of transgranular quasicleavage was observed. Larger grains induced a deterioration of the fatigue resistance of the HAZ.

An Experimental Evaluation of Electron Beam Welded Thixoformed 7075 Aluminum Alloy Plate Material

Directory of Open Access Journals (Sweden)

Ava Azadi Chegeni

2017-12-01

Full Text Available Two plates of thixoformed 7075 aluminum alloy were joined using Electron Beam Welding (EBW. A post-welding-heat treatment (PWHT was performed within the semi-solid temperature range of this alloy at three temperatures, 610, 617 and 628 °C, for 3 min. The microstructural evolution and mechanical properties of EB welded plates, as well as the heat-treated specimens, were investigated in the Base Metal (BM, Heat Affected Zone (HAZ, and Fusion Zone (FZ, using optical microscopy, Scanning Electron Microscopy (SEM, EDX (Energy Dispersive X-ray Analysis, and Vickers hardness test. Results indicated that after EBW, the grain size substantially decreased from 67 µm in both BM and HAZ to 7 µm in the FZ, and a hardness increment was observed in the FZ as compared to the BM and HAZ. Furthermore, the PWHT led to grain coarsening throughout the material, along with a further increase in hardness in the FZ.

Stripe-PZT Sensor-Based Baseline-Free Crack Diagnosis in a Structure with a Welded Stiffener.

Science.gov (United States)

An, Yun-Kyu; Shen, Zhiqi; Wu, Zhishen

2016-09-16

This paper proposes a stripe-PZT sensor-based baseline-free crack diagnosis technique in the heat affected zone (HAZ) of a structure with a welded stiffener. The proposed technique enables one to identify and localize a crack in the HAZ using only current data measured using a stripe-PZT sensor. The use of the stripe-PZT sensor makes it possible to significantly improve the applicability to real structures and minimize man-made errors associated with the installation process by embedding multiple piezoelectric sensors onto a printed circuit board. Moreover, a new frequency-wavenumber analysis-based baseline-free crack diagnosis algorithm minimizes false alarms caused by environmental variations by avoiding simple comparison with the baseline data accumulated from the pristine condition of a target structure. The proposed technique is numerically as well as experimentally validated using a plate-like structure with a welded stiffener, reveling that it successfully identifies and localizes a crack in HAZ.

Thermal effect of laser ablation on the surface of carbon fiber reinforced plastic during laser processing

Science.gov (United States)

Ohkubo, Tomomasa; Sato, Yuji; Matsunaga, Ei-ichi; Tsukamoto, Masahiro

2018-02-01

Although laser processing is widely used for many applications, the cutting quality of carbon fiber reinforced plastic (CFRP) decreases around the heat-affected zone (HAZ) during laser processing. Carbon fibers are exposed around the HAZ, and tensile strength decreases with increasing length of the HAZ. Some theoretical studies of thermal conductions that do not consider fluid dynamics have been performed; however, theoretical considerations that include the dynamics of laser ablation are scarce. Using removed mass and depth observed from experiments, the dynamics of laser ablation of CFRP with high-temperature and high-pressure of compressive gas is simulated herein. In this calculation, the mushroom-like shape of laser ablation is qualitatively simulated compared with experiments using a high-speed camera. Considering the removal temperature of the resin and the temperature distribution at each point on the surface, the simulation results suggest that a wide area of the resin is removed when the processing depth is shallow, and a rounded kerf is generated as the processing depth increases.

Effect of electromagnetic interaction during fusion welding of AISI 2205 duplex stainless steel on the corrosion resistance

Science.gov (United States)

García-Rentería, M. A.; López-Morelos, V. H.; González-Sánchez, J.; García-Hernández, R.; Dzib-Pérez, L.; Curiel-López, F. F.

2017-02-01

The effect of electromagnetic interaction of low intensity (EMILI) applied during fusion welding of AISI 2205 duplex stainless steel on the resistance to localised corrosion in natural seawater was investigated. The heat affected zone (HAZ) of samples welded under EMILI showed a higher temperature for pitting initiation and lower dissolution under anodic polarisation in chloride containing solutions than samples welded without EMILI. The EMILI assisted welding process developed in the present work enhanced the resistance to localised corrosion due to a modification on the microstructural evolution in the HAZ and the fusion zone during the thermal cycle involved in fusion welding. The application of EMILI reduced the size of the HAZ, limited coarsening of the ferrite grains and promoted regeneration of austenite in this zone, inducing a homogeneous passive condition of the surface. EMILI can be applied during fusion welding of structural or functional components of diverse size manufactured with duplex stainless steel designed to withstand aggressive environments such as natural seawater or marine atmospheres.

Hazardous Materials Pharmacies - A Vital Component of a Robust P2 Program

International Nuclear Information System (INIS)

McCarter, S.

2006-01-01

Integrating pollution prevention (P2) into the Department of Energy Integrated Safety Management (ISM) - Environmental Management System (EMS) approach, required by DOE Order 450.1, leads to an enhanced ISM program at large and complex installations and facilities. One of the building blocks to integrating P2 into a comprehensive environmental and safety program is the control and tracking of the amounts, types, and flow of hazardous materials used on a facility. Hazardous materials pharmacies (typically called HazMarts) provide a solid approach to resolving this issue through business practice changes that reduce use, avoid excess, and redistribute surplus. If understood from concept to implementation, the HazMart is a powerful tool for reducing pollution at the source, tracking inventory storage, controlling usage and flow, and summarizing data for reporting requirements. Pharmacy options can range from a strict, single control point for all hazardous materials to a virtual system, where the inventory is user controlled and reported over a common system. Designing and implementing HazMarts on large, diverse installations or facilities present a unique set of issues. This is especially true of research and development (R and D) facilities where the chemical use requirements are extensive and often classified. There are often multiple sources of supply; a wide variety of chemical requirements; a mix of containers ranging from small ampoules to large bulk storage tanks; and a wide range of tools used to track hazardous materials, ranging from simple purchase inventories to sophisticated tracking software. Computer systems are often not uniform in capacity, capability, or operating systems, making it difficult to use a server-based unified tracking system software. Each of these issues has a solution or set of solutions tied to fundamental business practices. Each requires an understanding of the problem at hand, which, in turn, requires good communication among all

The Influence of TIG Welding Thermal Cycles on HSLA-100 Steel Plate

Science.gov (United States)

1993-11-01

8217 1.0’ 1,i 1.0’ 10’ TZ•ME. Secznas Figure 15. CCT diagram for a HSLA-100 steel with composition similar to that of the present work from Wilson...cooling rate through the transformation and ends up with a HAZ hardness of 345 HV which indicates a predominantly martensitic structure, on the CCT ... diagram . This is confirmed by the TEM micrograph of the HAZ taken close to fusion boundary, figure 14. On the other hand, the high heat input weld 1, with

Characteristics of the Beam-Plasma Discharge; Caracteristiques de la 'Decharge Faisceau-Plasma'; ХАРАКТЕРИСТИКИ РАЗРЯДА ПУЧКА В ПЛАЗМЕ; Caracteristicas de la Descarga Haz-Plasma

Energy Technology Data Exchange (ETDEWEB)

Smullin, L. D.; Getty, W. D. [Massachusetts Institute of Technology, Cambridge, MA (United States)

1966-04-15

transversale de 10{sup 2} a 10{sup 3} eV. Les energies des rayons X mesurees permettent de conclure a l'existence d'electrons d'une energie de 50 a 100 keV. La decroissance du plasma apres la coupure du faisceau s'opere en deux etapes: perte relativement rapide en electrons de faible energie, {tau} Less-Than-Or-Equal-To 1000 {mu}s, et decroissance lente des electrons de haute energie, {tau} = 10 a 50 ms. Les auteurs font une deuxieme experience en utilisant les memes valeurs des parametres du faisceau d'electrons et la meme configuration du champ magnetique, dans le meme intervalle de pressions; les dimensions du plasma sont doubles. Ils obtiennent, pour l'energie du plasma, des parametres qui presentent des differences remarquables en introduisant un gaz par une vanne a gaz puise et en creant ainsi un gradient de pressions. Le pompage du gaz par le plasma est sensiblement diminue, la densite et l'energie du plasma etant les memes. Les energies maximum et moyenne des electrons sont decuples par rapport aux valeurs qu'elles atteignent lorsque la densite du gaz est uniforme. On observe parfois une rupture d'instabilite dans le trainage, qui correspond a une perte du plasma a basse energie. (author) [Spanish] En esta memoria se resumen los trabajos reciente- ' mente realizados en el 041C 041B . 0422 . con miras a estudiar la interaccion de un haz electronico con un plasma. Cuando un haz de electrones atraviesa un plasma, excita oscilaciones a la frecuencia del plasma. Estas oscilaciones de micro-ondas mantienen una descarga de micro-ondas; los autores han denominado el proceso completo 'descarga haz-plasma'. La ionizacion del gas ambiental es realizada por los electrones plasmaticos . de alta energia, previamente acelerados por los campos oscilatorios. El resultado es la formacion de un plasma de electrones calientes dentro del espejo magnetico. Puesto que los parametros de la descarga haz-plasma no parecen favorecer el calentamiento directo de los iones por una interaccion haz

Re-austenitisation of chromium-bearing pressure vessel steels during the weld thermal cycle

International Nuclear Information System (INIS)

Dunne, Druce; Li, Huijun; Jones, Christopher

2013-01-01

Steels with chromium contents between 0.5 and 12 wt% are commonly used for fabrication of creep resistant pressure vessels (PV) for the power generation industry. Most of these steels are susceptible to Type IV creep failure in the intercritical and/ or grain refined regions of the heat affected zone (HAZ) of the parent metal. The re-austenitisation process plays a central role in establishing the transformed microstructures and the creep resistance of the various sub-zones of the HAZ. The high alloy content and the presence of alloy-rich carbides in the as-supplied parent plate can significantly retard the kinetics of transformation to austenite, resulting in both incomplete austenitisation and inhomogeneous austenite. Overlapping weld thermal cycles in multi-pass welds add further complexity to the progressive development of microstructure over the course of the welding process. In order to clarify structural evolution, thermal simulation has been used to study the effects of successive thermal cycles on the structures and properties of the HAZ of 2.25Cr-1Mo steel. The results showed that, before post-weld heat treatment (PWHT), the HAZ microstructures and properties, particularly in doubly reheated sub-zones, were highly heterogeneous and differed markedly from those of the base steel. It is concluded that close control of the thermal cycle by pre-heat, weld heat input and post-heat is necessary to obtain a heat affected zone with microstructures and properties compatible with those of the base plate.

Grain topology in Ti-6Al-4V welds-Monte Carlo simulation and experiments

International Nuclear Information System (INIS)

Mishra, S; DebRoy, T

2004-01-01

The importance of topological features of grains in the evolution of grain structure is well recognized in isothermal systems. However, during fusion welding, strong spatial gradients of temperature exist in the heat-affected zone (HAZ), and this region undergoes rapid heating and cooling. The effects of spatial and temporal variations of temperature on the topological class distribution, relationship between size and topology of grains and the interdependence between grain topology and its neighbours are not known. Topological features of grains in the HAZ of Ti-6Al-4V alloy welds were measured for various heat inputs in the range 0.55-4.33 MJ m -1 . The topological class distributions were also calculated using a three-dimensional Monte Carlo model utilizing thermal cycles computed from a well tested numerical heat transfer and fluid flow model. The computed results showed that the topological class distributions were unaffected by the spatial and temporal variations of temperature. Experimental investigations of a few sections confirmed the simulation results. The average grain size for each edge class varied linearly with the edge class number. The local topological environment, i.e. the average number of sides of neighbours, n n , varied linearly with the inverse of the number of sides of grains, 1/n r , at a given location in the HAZ. Locations with the same topological environment showed the same grain size, indicating the significant influence of grain topology on grain growth in the HAZ

Microstructural response to heat affected zone cracking of prewelding heat-treated Inconel 939 superalloy

Energy Technology Data Exchange (ETDEWEB)

Gonzalez, M.A., E-mail: mgonzalez@comimsa.com.mx [Facultad de Ingenieria Mecanica y Electrica (FIME-UANL), Av. Universidad s/n. Ciudad Universitaria, C.P.66451 San Nicolas de los Garza, N.L. (Mexico); Martinez, D.I., E-mail: dorairma@yahoo.com [Facultad de Ingenieria Mecanica y Electrica (FIME-UANL), Av. Universidad s/n. Ciudad Universitaria, C.P.66451 San Nicolas de los Garza, N.L. (Mexico); Perez, A., E-mail: betinperez@hotmail.com [Facultad de Ingenieria Mecanica y Electrica (FIME-UANL), Av. Universidad s/n. Ciudad Universitaria, C.P.66451 San Nicolas de los Garza, N.L. (Mexico); Guajardo, H., E-mail: hguajardo@frisa.com [FRISA Aerospace, S.A. de C.V., Valentin G. Rivero No. 200, Col. Los Trevino, C.P. 66150, Santa Caterina N.L. (Mexico); Garza, A., E-mail: agarza@comimsa.com [Corporacion Mexicana de Investigacion en Materiales S.A. de C.V. (COMIMSA), Ciencia y Tecnologia No.790, Saltillo 400, C.P. 25295 Saltillo Coah. (Mexico)

2011-12-15

The microstructural response to cracking in the heat-affected zone (HAZ) of a nickel-based IN 939 superalloy after prewelding heat treatments (PWHT) was investigated. The PWHT specimens showed two different microstructures: 1) spherical ordered {gamma} Prime precipitates (357-442 nm), with blocky MC and discreet M{sub 23}C{sub 6} carbides dispersed within the coarse dendrites and in the interdendritic regions; and 2) ordered {gamma} Prime precipitates in 'ogdoadically' diced cube shapes and coarse MC carbides within the dendrites and in the interdendritic regions. After being tungsten inert gas welded (TIG) applying low heat input, welding speed and using a more ductile filler alloy, specimens with microstructures consisting of spherical {gamma} Prime precipitate particles and dispersed discreet MC carbides along the grain boundaries, displayed a considerably improved weldability due to a strong reduction of the intergranular HAZ cracking associated with the liquation microfissuring phenomena. - Highlights: Black-Right-Pointing-Pointer Homogeneous microstructures of {gamma} Prime spheroids and discreet MC carbides of Ni base superalloys through preweld heat treatments. Black-Right-Pointing-Pointer {gamma} Prime spheroids and discreet MC carbides reduce the intergranular HAZ liquation and microfissuring of Nickel base superalloys. Black-Right-Pointing-Pointer Microstructure {gamma} Prime spheroids and discreet blocky type MC carbides, capable to relax the stress generated during weld cooling. Black-Right-Pointing-Pointer Low welding heat input welding speeds and ductile filler alloys reduce the HAZ cracking susceptibility.

Effect of post-weld heat treatment on the mechanical properties of CLAM/316L dissimilar joint

Energy Technology Data Exchange (ETDEWEB)

Zhang, Junyu [Key Laboratory of Neutronics and Radiation Safety, Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); University of Science and Technology of China, Hefei, Anhui 230027 (China); Huang, Bo [Key Laboratory of Neutronics and Radiation Safety, Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Wu, Qingsheng, E-mail: qingsheng.wu@fds.org.cn [Key Laboratory of Neutronics and Radiation Safety, Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Li, Chunjing; Huang, Qunying [Key Laboratory of Neutronics and Radiation Safety, Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui 230031 (China)

2015-11-15

Highlights: • Dissimilar joints between CLAM and 316L steels welded by TIG were investigated. • After PWHTs, the hardening in HAZ on the CLAM steel side decreased remarkably. • Tempering at 740 °C for 2 h was considered as the preferable treatment rule. - Abstract: Dissimilar welding between China low activation martensitic (CLAM) steel and 316L austenitic stainless steel was investigated to achieve the reliable connection between test blanket modules (TBMs) and piping system in the international thermonuclear experimental reactor (ITER). The dissimilar joints were welded by tungsten inert gas (TIG) welding process with a filler material type-309. In order to stabilize the microstructure and improve the strength and toughness, post-weld heat treatments (PWHTs) of tempering at 740 °C, 780 °C and 820 °C, respectively, for 2 h were performed. The microstructure observation showed that tempering at 740 °C for 2 h was the preferable PWHT rule in this work. After the treatment, the hardening in heat affected zone (HAZ) on the CLAM steel side decreased remarkably. The tensile strength of the joint was roughly the same as that of the base metal. The impact toughness of HAZ on the CLAM steel side was 77% of that of the base metal. The absorbed energy of HAZ of 316L steel decreased by 93 J, and that of weld metal (WM) was 110 J after the treatment.

Furniture Rack Corrosion Coupon Surveillance - 2012 Update

International Nuclear Information System (INIS)

Mickalonis, J. I.; Murphy, T. R.; Berry, C. J.

2012-01-01

Under the L Basin corrosion surveillance program furniture rack coupons immersed for 14 years (FY2009 coupons) and 16 years (FY2011 coupons) were analyzed and the results trended with coupons exposed for shorter times. In addition, a section harvested from an actual furniture rack that was immersed for 14 years was analyzed for pitting in the weld and heat-affected-zone (HAZ) regions. The L Basin operations maintained very good water quality over the entire immersion period for these samples. These results for FY2009 and FY2011 coupons showed that the average pit depths for the 6061 and 6063 base metal are 1 and 2 mils, respectively, while those for the weld and HAZ are 3 and 4 mils, respectively. The results for the weld and HAZ regions are similar to coupons removed during the period of FY2003 to FY2007. These similarities indicate that the pit development occurred quickly followed by slow kinetics of increase in pit depth. For the actual furniture rack sample average pits of 5 and 2 mils were measured for the HAZ and weld, respectively. These results demonstrate that pitting corrosion of the aluminum furniture racks used to support the spent fuel occurs in waters of good quality. The corrosion kinetics or pit depth growth rate is much less that 1 mil/year, and would not impact long-term use of this material system for fuel storage racks in L Basin if good water quality is maintained

Microstructure of a safe-end dissimilar metal weld joint (SA508-52-316L) prepared by narrow-gap GTAW

Energy Technology Data Exchange (ETDEWEB)

Ming, Hongliang [Key Laboratory of Nuclear Materials and Safety Assessment, Liaoning Key Laboratory for Safety and Assessment Technique of Nuclear Materials, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China); University of Chinese Academy of Sciences, 19 Yuquan Road, Beijing 100049 (China); Zhang, Zhiming [Key Laboratory of Nuclear Materials and Safety Assessment, Liaoning Key Laboratory for Safety and Assessment Technique of Nuclear Materials, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China); Wang, Jianqiu, E-mail: wangjianqiu@imr.ac.cn [Key Laboratory of Nuclear Materials and Safety Assessment, Liaoning Key Laboratory for Safety and Assessment Technique of Nuclear Materials, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China); Han, En-Hou [Key Laboratory of Nuclear Materials and Safety Assessment, Liaoning Key Laboratory for Safety and Assessment Technique of Nuclear Materials, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China); Wang, Peipei; Sun, Zhiyuan [Shanghai Research Center for Weld and Detection Engineering Technique of Nuclear Equipment, Shanghai 201306 (China)

2017-01-15

The microstructure, residual strain and interfacial chemical composition distribution of a safe-end dissimilar metal weld joint (DMWJ, SA508-52-316L) prepared by narrow-gap gas-tungsten arc welding (NG-GTAW) were studied by optical microscope (OM) and scanning electron microscope equipped with an energy dispersive X-ray microanalysis (SEM/EDX) and an electron back scattering diffraction (EBSD) system. Complex microstructure and chemical composition distribution are found, especially at the SA508-52 interface and the 52-316L interface. In brief, a complicated microstructure transition exists within the SA508 heat affected zone (HAZ); the residual strain, the fraction of high angle random grain boundaries and low angle boundaries decrease with increasing the distance from the fusion boundary in 316L HAZ; neither typical type II boundary nor obvious carbon-depleted zone is found near the SA508-52 interface; dramatic and complicated changes of the contents of the main elements, Fe, Cr and Ni, are observed at the distinct interfaces, especially at the SA508-52 interface. No carbon concentration is found at the SA508-52 interface. - Highlights: •Residual strain and GBCD change as a function of the distance from FB in 316L HAZ. •Neither type II boundary nor obvious carbon-depleted zone is found in SA508 HAZ. •No carbon concentration is found at the SA508-52 interface. •The middle part of the DMWJ has the highest residual strain.

Microstructure and Hardness Variation in a TIG Weldment of Irradiated F82H

International Nuclear Information System (INIS)

Tanigawa, H.; Ando, M.; Sawai, T.; Shiba, K.; Hashimoto, N.; Klueh, R.L.

2003-01-01

Previous work reported that a TIG weld joint of F82H exhibited low irradiation hardening in a tensile test, compared to the base metal. Microhardness tests and microstructure observation on the neutron-irradiated TIG weld joint of F82H revealed that the over-tempered zone in the heat-affected zone (HAZ) exhibited this good performance. The region in the HAZ where the prior austenite grain size became very fine during welding also exhibited lower irradiation hardening. Hypotheses for these low-hardening mechanisms were proposed based on the phase diagram and grain size

Microstructure characteristics and mechanical properties of laser-TIG hybrid welded dissimilar joints of Ti-22Al-27Nb and TA15

Science.gov (United States)

Zhang, Kezhao; Lei, Zhenglong; Chen, Yanbin; Liu, Ming; Liu, Yang

2015-10-01

Laser-TIG-hybrid-welding (TIG - tungsten inert gas) process was successfully applied to investigate the microstructure and tensile properties of Ti-22Al-27Nb/TA15 dissimilar joints. The HAZ of the arc zone in Ti-22Al-27Nb was characterized by three different regions: single B2, B2+α2 and B2+α2+O, while the single B2 phase region was absent in the HAZ of the laser zone. As for the HAZ in TA15 alloy, the microstructure mainly contained acicular α‧ martensites near the fusion line and partially remained the lamellar structure near the base metal. The fusion zone consisted of B2 phase due to the relatively high content of β phase stabilizing elements and fast cooling rate during the welding process. The tensile strength of the welds was higher than that of TA15 alloy because of the fully B2 microstructure in the fusion zone, and the fracture preferentially occurred on the base metal of TA15 alloy during the tensile tests at room temperature and 650 °C.

Laser cutting of graphite anodes for automotive lithium-ion secondary batteries: investigations in the edge geometry and heat-affected zone

Science.gov (United States)

Schmieder, Benjamin

2012-03-01

To serve the high need of lithium-ion secondary batteries of the automobile industry in the next ten years it is necessary to establish highly reliable, fast and non abrasive machining processes. In previous works [1] it was shown that high cutting speeds with several meters per second are achievable. For this, mainly high power single mode fibre lasers with up to several kilo watts were used. Since lithium-ion batteries are very fragile electro chemical systems, the cutting speed is not the only thing important. To guarantee a high cycling stability and a long calendrical life time the edge quality and the heat affected zone (HAZ) are equally important. Therefore, this paper tries to establish an analytical model for the geometry of the cutting edge based on the ablation thresholds of the different materials. It also deals with the composition of the HAZ in dependence of the pulse length, generated by laser remote cutting with pulsed fibre laser. The characterisation of the HAZ was done by optical microscopy, SEM, EDX and Raman microscopy.

Double Fillet Welding of Carbon Steel T-Joint by Double Channel Shielding Gas Metal Arc Welding Method Using Metal Cored Wire

Directory of Open Access Journals (Sweden)

Mert T.

2017-06-01

Full Text Available Low carbon steel material and T-joints are frequently used in ship building and steel constructions. Advantages such as high deposition rates, high quality and smooth weld metals and easy automation make cored wires preferable in these industries. In this study, low carbon steel materials with web and flange thicknesses of 6 mm, 8 mm and 10 mm were welded with conventional GMAW and double channel shielding gas metal arc welding (DMAG method to form double fillet T-joints using metal cored wire. The difference between these two methods were characterized by measurements of mean welding parameters, Vickers hardness profiles, weld bead and HAZ geometry of the joints and thermal camera temperature measurements. When weld bead and HAZ geometries are focused, it was seen filler metal molten area increased and base metal molten area decreased in DMAG of low carbon steel. When compared with traditional GMAW, finer and acicular structures in weld metal and more homogenous and smaller grains in HAZ are obtained with double channel shielding gas metal arc welding.

Weldability prequalification of steels for deep water service

Energy Technology Data Exchange (ETDEWEB)

Hayes, Michael D. [Acute Technological Services, Inc., Houston, TX (United States); Ibarra, S. Jim [BP America (United States); Fazackerley, W.J. [EWI Microalloying, Houston, TX (United States)

2004-07-01

The weldability of steels for deep water applications must be determined long before welding procedures are qualified. The weldments of deep water equipment such as steel Catenary risers (SCRs) are subjected to currents which result in high cyclic stresses. It is imperative that steels selected for such service have high CTOD fracture toughness values after welding to ensure good defect tolerance. Through fracture mechanics analyses, these CTOD values are used to determine the defect acceptance criteria that is used for inspection of such weldments. The base metal and weld metal are more easily obtained, but because the weld joint design changes the position of the HAZs, the CTOD value for the HAZ is usually a combination of the base, weld consumable, and HAZ. The value obtained from such a test is suspect, and may give an optimistic value if the weld metal or base metal have high CTOD values. This paper discusses the various strategies for determining the true weldability long before construction commences, using API RP 2Z (1) Type tests for prequalification of base materials. (author)

Ductility dip cracking susceptibility of Inconel Filler Metal 52 and Inconel Alloy 690

International Nuclear Information System (INIS)

Kikel, J.M.; Parker, D.M.

1998-01-01

Alloy 690 and Filler Metal 52 have become the materials of choice for commercial nuclear steam generator applications in recent years. Filler Metal 52 exhibits improved resistance to weld solidification and weld-metal liquation cracking as compared to other nickel-based filler metals. However, recently published work indicates that Filler Metal 52 is susceptible to ductility dip cracking (DDC) in highly restrained applications. Susceptibility to fusion zone DDC was evaluated using the transverse varestraint test method, while heat affected zone (HAZ) DDC susceptibility was evaluated using a newly developed spot-on-spot varestraint test method. Alloy 690 and Filler Metal 52 cracking susceptibility was compared to the DDC susceptibility of Alloy 600, Filler Metal 52, and Filler Metal 625. In addition, the effect of grain size and orientation on cracking susceptibility was also included in this study. Alloy 690, Filler Metal 82, Filler Metal 52, and Filler Metal 625 were found more susceptible to fusion zone DDC than Alloy 600. Filler Metal 52 and Alloy 690 were found more susceptible to HAZ DDC when compared to wrought Alloy 600, Filler Metal 82 and Filler Metal 625. Filler Metal 52 exhibited the greatest susceptibility to HAZ DDC of all the weld metals evaluated. The base materials were found much more resistant to HAZ DDC in the wrought condition than when autogenously welded. A smaller grain size was found to offer greater resistance to DDC. For weld metal where grain size is difficult to control, a change in grain orientation was found to improve resistance to DDC

Significance of reheat cracks to the integrity of pressure vessels for light-water reactors

International Nuclear Information System (INIS)

Canonico, D.A.

1977-01-01

Reheat cracks usually manifest themselves as macroscopic defects, which are centimeters long and deep, and are detectable by the usual nondestructive examination (NDE) procedures or as microscopic grain boundary decohesions (GBD) that are beyond the limit of detection by commercial NDE procedures. This report has concentrated on the significance of the microscopic cracks that may go undetected. The probability that GBD exist in the heat-affected zones (HAZ) of weldments of pressure vessel steels is high; particularly in SA 508 Class 2 weldments. A sample of the HAZ from the prolongation-weldment from the Heavy Section Steel Technology program Intermediate Test Vessel (ITV) No. 4 was examined by the Staatliche Materialprufungsanstalt (MPA). They reported GBD 5 mm (0.2 in.) long. This prompted an examination of the HAZ from the ITV vessel that had been tested to failure at 24 0 C (75 0 F). During testing, the region of the weld which contained the flaw that initiated the failure was strained up to 0.5%. A metallographic examination of this region of the weldment revealed GBD, but none of the size reported by the MPA. Further, there was no evidence that the GBD had extended as a consequence of the tests. Fracture toughness tests were made of the HAZ of welds from ITV-4. The electron-beam welding procedure, which permits more accurate siting of the crack, was used. Fracture toughness values in excess of 220 MPa root m (200 ksi root in.) were obtained at -18 0 C

Relation between sensitization and failures of welded joints at furnaces of Cienfuegos refinery

International Nuclear Information System (INIS)

Dominguez, H.; Menendez, C.M.; Sendoya, F.A.

1992-01-01

This work is concerned about the possible relation between sensitization and failures of welded joints at furnaces of Cienfuegos Refinery. This failures were detected in austenitic pipes by hydraulic testing. For determined the tendency to sensitization of heat affected zones (HAZ) of welded joints and piping, have been used standardized test methods AM and AMU (GOST 6032-89). In addition, the Electrochemical Potentiokinetic Reactivation (EPR) test was employed to quantity the tendency to intergranular corrosion. It was found that degree of sensitization was higher at HAZ and as a possible explanation is proposed the overheating during welding

Heat-affected-zone toughness in heavy wall pipe: Final report

Energy Technology Data Exchange (ETDEWEB)

Dyck, K.; Glover, A.G.; Varo, D.B.

1988-02-01

The objective of this program has been to determine the significance of low toughness regions on the service performance of heat-affected zones in heavy wall pipe materials. The low temperature HAZ toughness of welds in microalloyed and quenched and tempered materials at two heat inputs was established, a test technique to produce fatigue cracks in the HAZ was developed, and four full scale fracture tests were completed at /minus/49/degree/F. Publication available from the American Gas Association Order Processing Department, 1515 Wilson Boulevard, Arlington, Virginia 22209-2470 (703/841-8558). 17 refs. (JL)

Efecto de los ciclos térmicos sobre la ZAT de una soldadura multipasos de un acero inoxidable superdúplex SAF 2507 Effect of thermal cycles on the HAZ of a stainless steel multipass weld of superduplex SAF 2507

Directory of Open Access Journals (Sweden)

D. Villalobos

2010-09-01

Full Text Available Los ciclos térmicos de una soldadura multipasos que experimenta un acero inoxidable superdúplex SAF 2507, pueden promover la precipitación de fases secundarias reduciendo significativamente las propiedades mecánicas y la resistencia a la corrosión. Debido a su aplicación en la industria petroquímica, el estudio de las aleaciones superdúplex es de suma importancia para predecir su comportamiento en servicio cuando están involucrados procesos de soldadura por arco eléctrico. En este trabajo, se estudia el cambio microestructural de la zona afectada térmicamente correspondiente al primer cordón depositado de una unión multipasos de acero inoxidable superdúplex SAF 2507 mediante el proceso GTAW y bajo tres temperaturas de interpasos. Los resultados muestran que la temperatura de interpasos tiene una influencia sobre la precipitación de fase sigma en la zona afectada térmicamente del primer cordón depositado.Thermal cycles experienced by a superduplex stainless steel SAF 2507 when is welded, can promote the precipitation of secondary phases which decrease the mechanical properties as well as the corrosion resistance. Due to the application of the duplex alloys in the petrochemical industry, the study of these alloys has become very important in order to predict its service behavior. The aim of this work is to study the microstructural changes in the superduplex stainless steel weld joint after applying the GTAW process under three interpass temperatures after the deposition of every single pass. The results showed that slow cooling rates promoted by the deposition of the subsecuent passes and the higher interpass temperature, promote the precipitation of sigma phase in the HAZ while rapid cooling rates promoted by the lower interpass temperature do not promote the sigma phase precipitation.

High temperature strength analysis of welded joint of RAF's by small punch test

Energy Technology Data Exchange (ETDEWEB)

Kato, T. [Muroran Institute of Technology, Dept. of Materials Science and Engineeering, Hokkaido (Japan); Komazaki, S.; Kohno, Y. [Muroran Institute of Technology, Muroran (Japan); Tanigawa, H. [Japan Atomic Energy Agency, Naga-gun, Ibaraki-ken (Japan); Kohyama, A. [Kyoto Univ., Institute of Advanced Energy (Japan)

2007-07-01

Full text of publication follows: Nucleation and growth of microvoids and/or small cracks in fine-grained heat affected zone (HAZ) after long-term service operation, which is recognized as Type IV creep damage, has recently been a worldwide issue for high Cr ferritic steels. In our group, a small punch (SP) creep test has been successfully applied to evaluate this damage of low alloy ferritic steel. However, the HAZ of fusion reactor material welded by electron-beam (EB) welding is so narrow that it is not easy to evaluate its mechanical properties by conventional tests including the SP creep test with a plate-type specimen (10 x 10 x 0.5 mm{sup 3}). In this study, the SP creep test using a further miniaturized specimen was developed and applied to the welded joint of reduced activation ferritic steels (RAFs), F82H-IEA (Fe-8Cr-2W-0.2V-0.02Ta), for measuring creep properties of the HAZ. For the SP creep test, TEM disk-type samples (diam. 3.0 x 0.30 mm) were removed from the base metal (BM), weld metal (WM) and HAZ, respectively. The specimen surfaces were polished up to a 0.05 {mu}m alumina powder finish and the specimen's thickness was finally adjusted to 0.25 mm. The SP creep tests were performed at temperatures of 823{approx}973 K and under loads ranging from 20 to 200 N. A constant load was applied to the center of the specimen through the Si{sub 3}N{sub 4} bail (diam. 1.0 mm) using the electric servo motor. The central deflection of the specimen was monitored by measuring the displacement of the compression rod. The tests were carried out in an argon gas atmosphere and the gas was continuously passed through during the test to prevent severe oxidation of the specimen. The differences in SP creep properties such as rupture time and minimum creep rate between the BM, WM and HAZ were discussed in terms of microstructural changes during welding thermal cycles. In addition, the result obtained from the BM was correlated with those of uniaxial creep test

Materials and welding process development for nuclear application in the Federal Republic of Germany

International Nuclear Information System (INIS)

Kussmaul, K.; Stoppler, W.; Sinz, R.

1982-01-01

The concept of Basis Safety was developed in the Federal Republic of Germany (FRG) in order to achieve exclusion of catastrophic failure of pressure boundary components in Light Water Reactors (LWRs). This concept provides redundant safeties both for long-term service as well as for an accident by improving toughness properties of the base material (BM), heat-affected zone (HAZ) and deposited metal (DM) of components with relevance safety. With the help of the welding simulation technique, the toughness properties in the HAZ was investigated as a function of stress-relief temperature. Submerged-arc welding (SAW) on heavy section components were investigated during and after welding. This helped to delineate boundary conditions for a computer code for the design and optimization of a joint and its HAZ. The advantage of the narrow gap technique is the extremely low amount of sensitive coarse grained zones. Processing tough filler materials with optimum weld parameters will provide excellent material properties at an elevated strength level in shape-welded heavy section components. The martensitic steel X 20 CrMoV 12 has an excellent weldability of the BM (HAZ without problems), but it has not been possible up to now, to achieve equal properties for the deposited material. This is also the case for martensitic welding. As far as austenitic steels are concerned the sulfur content had also to be lowered. Sufficient toughness had to be proved also in the case of impact loading for austenitic welded joints subsequent to thermal aging. Susceptibility to corrosion of individual austenitic materials and material conditions was investigated and remedies elaborated. 33 figures, 7 tables

Effect of heat input on dissimilar welds of ultra high strength steel and duplex stainless steel: Microstructural and compositional analysis

Energy Technology Data Exchange (ETDEWEB)

Tasalloti, H., E-mail: hamed.tasalloti.kashani@student.lut.fi; Kah, P., E-mail: paul.kah@lut.fi; Martikainen, J., E-mail: jukka.martikainen@lut.fi

2017-01-15

The effect of heat input on the microstructure and compositional heterogeneity of welds of direct-quenched ultra high strength steel (Optim 960 QC) and duplex stainless steel (UNS S32205) was studied. The dissimilar welds were made using GMAW with a fully austenitic filler wire. In addition to grain coarsening in the heat affected zone (HAZ) of the ferritic side, it was found that an increase in heat input correlatively increased the proportional volume of bainitic to martensitic phases. Coarse ferritic grains were observed in the duplex HAZ. Higher heat input, however, had a beneficial effect on the nucleation of austenite in the HAZ. Heat input had a regulatory effect on grain growth within the austenitic weld and more favorable equiaxed austenite was obtained with higher heat input. On the ferritic side of the welds, macrosegregation in the form of a martensitic intermediate zone was observed for all the cooling rates studied. However, on the duplex side, macrosegregation in the fusion boundary was only noticed with higher cooling rates. Microstructural observations and compositional analysis suggest that higher heat input could be beneficial for the structural integrity of the weld despite higher heat input increasing the extent of adverse coarse grains in the HAZ, especially on the ferritic side. - Highlights: •The effect of heat input on dissimilar welds of UHSS and DSS was studied. •Transmutation of the microstructure was discussed in detail. •The influence of heat input on compositional heterogeneity of welds was described. •Higher heat input enhanced bainitic transformation on the ferritic side. •Macrosegregation was affected by the amount of heat input on the DSS side.

Quantifying and exploiting the age dependence in the effect of supplementary food for child undernutrition.

Directory of Open Access Journals (Sweden)

Milinda Lakkam

Full Text Available Motivated by the lack of randomized controlled trials with an intervention-free control arm in the area of child undernutrition, we fit a trivariate model of weight-for-age z score (WAZ, height-for-age z score (HAZ and diarrhea status to data from an observational study of supplementary feeding (100 kCal/day for children with WAZ [Formula: see text] in 17 Guatemalan communities. Incorporating time lags, intention to treat (i.e., to give supplementary food, seasonality and age interactions, we estimate how the effect of supplementary food on WAZ, HAZ and diarrhea status varies with a child's age. We find that the effect of supplementary food on all 3 metrics decreases linearly with age from 6 to 20 mo and has little effect after 20 mo. We derive 2 food allocation policies that myopically (i.e., looking ahead 2 mo minimize either the underweight or stunting severity - i.e., the sum of squared WAZ or HAZ scores for all children with WAZ or HAZ [Formula: see text]. A simulation study based on the statistical model predicts that the 2 derived policies reduce the underweight severity (averaged over all ages by 13.6-14.1% and reduce the stunting severity at age 60 mo by 7.1-8.0% relative to the policy currently in use, where all policies have a budget that feeds [Formula: see text]% of children. While these findings need to be confirmed on additional data sets, it appears that in a low-dose (100 kCal/day supplementary feeding setting in Guatemala, allocating food primarily to 6-12 mo infants can reduce the severity of underweight and stunting.

A comparative study of the microstructure and properties of 800 MPa microalloyed C-Mn steel welded joints by laser and gas metal arc welding

Energy Technology Data Exchange (ETDEWEB)

Sun, Qian [The State Key Laboratory of Rolling and Automation of Northeastern University, Shenyang 110819 (China); Di, Hong-Shuang, E-mail: hongshuangdi_ral@126.com [The State Key Laboratory of Rolling and Automation of Northeastern University, Shenyang 110819 (China); Li, Jun-Chen [The State Key Laboratory of Rolling and Automation of Northeastern University, Shenyang 110819 (China); Wu, Bao-Qiang [National Key Laboratory for Precision Hot Processing of Metals, Harbin Institute of Technology, Harbin 150001 (China); Misra, R.D.K. [Laboratory for Excellence in Advanced Steel Research, Department of Metallurgical, Material and Biomedical Engineering, University of Texas at El Paso, TX 79968 (United States)

2016-07-04

The differences in microstructure and mechanical properties of laser beam welded (LBW) and gas metal arc welded (GMAW) joints of 800 MPa grade Nb-Ti-Mo microalloyed C-Mn steel of 5 mm thickness were studied. The study suggested that the microstructure in welded seam (WS) of GMAW was acicular ferrite and fine grained ferrite, whereas lath martensite (LM) was obtained in WS of LBW, where inclusions were finer and did not act as nucleation sites for acicular ferrite. The microstructure of coarse-grained HAZ (CGHAZ) obtained using the two welding methods was LM and granular bainite (GB), respectively. The original austenite grain size in CGHAZ of LBW was 1/3 of GMAW. The microstructure of fine-grained HAZ and mixed-grained HAZ using the two welding methods was ferrite and M-A constituents, while that of LBW was significantly fine. The hardness of LBW welded joints was higher than the base metal (BM), which was the initiation site for tensile fracture. The tensile fracture location of GMAW welded joints was in WS. The impact toughness of LBW welded joints was excellent and the impact absorption energy was similar to BM.

Microestructuras producidas en la soldadura de unión de aceros para tuberías de gran diámetro

Directory of Open Access Journals (Sweden)

Salazar, M.

1998-12-01

Full Text Available This is an evaluation of the microstructure in the heat affected zone (HAZ of steel weldings used in pipe lines. The welding was made by shielding metal are welding. This is a welding process with multiple run and low heat input, however local brittle zones are present in the HAZ. These are originated by a complex mechanism that is influenced by welding parameters and chemical composition of the steel. The welding sequences that help to eliminate the local brittle zones are studied.

En este trabajo se estudian las microestructuras producidas en la zona afectada por el calor (HAZ de la soldadura de unión en aceros utilizados en la construcción de poliductos. Se analizan las juntas obtenidas mediante soldadura manual con electrodo revestido. A pesar de que este es un proceso de soldadura con un bajo aporte térmico, se encuentran zonas frágiles locales que se originan por un mecanismo complejo influido por parámetros de soldadura y composición química del acero. Se analizan secuencias de soldaduras que ayuden a la desaparición de las mismas.

Statistical characteristics of surface integrity by fiber laser cutting of Nitinol vascular stents

International Nuclear Information System (INIS)

Fu, C.H.; Liu, J.F.; Guo, Andrew

2015-01-01

Graphical abstract: - Highlights: • Precision kerf with tight tolerance of Nitinol stents can be cut by fiber laser. • No HAZ in the subsurface was detected due to large grain size. • Recast layer has lower hardness than the bulk. • Laser cutting speed has a higher influence on surface integrity than laser power. - Abstract: Nitinol alloys have been widely used in manufacturing of vascular stents due to the outstanding properties such as superelasticity, shape memory, and superior biocompatibility. Laser cutting is the dominant process for manufacturing Nitinol stents. Conventional laser cutting usually produces unsatisfactory surface integrity which has a significant detrimental impact on stent performance. Emerging as a competitive process, fiber laser with high beam quality is expected to produce much less thermal damage such as striation, dross, heat affected zone (HAZ), and recast layer. To understand the process capability of fiber laser cutting of Nitinol alloy, a design-of-experiment based laser cutting experiment was performed. The kerf geometry, roughness, topography, microstructure, and hardness were studied to better understand the nature of the HAZ and recast layer in fiber laser cutting. Moreover, effect size analysis was conducted to investigate the relationship between surface integrity and process parameters.

Statistical characteristics of surface integrity by fiber laser cutting of Nitinol vascular stents

Energy Technology Data Exchange (ETDEWEB)

Fu, C.H., E-mail: cfu5@crimson.ua.edu [Dept of Mechanical Engineering, The University of Alabama, Tuscaloosa, AL 35487 (United States); Liu, J.F. [Dept of Mechanical Engineering, The University of Alabama, Tuscaloosa, AL 35487 (United States); Guo, Andrew [Dept of Mechanical Engineering, The University of Alabama, Tuscaloosa, AL 35487 (United States); College of Arts and Science, Vanderbilt University, Nashville, TN 37235 (United States)

2015-10-30

Graphical abstract: - Highlights: • Precision kerf with tight tolerance of Nitinol stents can be cut by fiber laser. • No HAZ in the subsurface was detected due to large grain size. • Recast layer has lower hardness than the bulk. • Laser cutting speed has a higher influence on surface integrity than laser power. - Abstract: Nitinol alloys have been widely used in manufacturing of vascular stents due to the outstanding properties such as superelasticity, shape memory, and superior biocompatibility. Laser cutting is the dominant process for manufacturing Nitinol stents. Conventional laser cutting usually produces unsatisfactory surface integrity which has a significant detrimental impact on stent performance. Emerging as a competitive process, fiber laser with high beam quality is expected to produce much less thermal damage such as striation, dross, heat affected zone (HAZ), and recast layer. To understand the process capability of fiber laser cutting of Nitinol alloy, a design-of-experiment based laser cutting experiment was performed. The kerf geometry, roughness, topography, microstructure, and hardness were studied to better understand the nature of the HAZ and recast layer in fiber laser cutting. Moreover, effect size analysis was conducted to investigate the relationship between surface integrity and process parameters.

Undernutrition, subsequent risk of mortality and civil war in Burundi.

Science.gov (United States)

Verwimp, Philip

2012-07-01

The paper investigates the effect of child undernutrition on the risk of mortality in Burundi. Using anthropometric data from a longitudinal survey (1998-2007) we find that undernourished children, measured by the height-for-age z-scores (HAZ) in 1998 had a higher probability to die during subsequent years. In order to address the problem of omitted variables correlated with both nutritional status and the risk of mortality, we use the length of exposure to civil war prior to 1998 as a source of exogenous variation in a child's nutritional status. Children exposed to civil war in their area of residence have worse nutritional status. The results indicate that one year of exposure translates into a 0.15 decrease in the HAZ, resulting in a 10% increase in the probability to die. For boys, we find a 0.34 decrease in HAZ per year of exposure, resulting in 25% increase in the probability to die. For girls, the results are statistically not significant at the usual thresholds. We show the robustness of our results and we derive policy conclusion for a nutrition intervention in times of conflict. Copyright © 2011 Elsevier B.V. All rights reserved.

Corrosion Behavior of Heat Affected Zone of AISI 321 stainless steel

International Nuclear Information System (INIS)

Ahn, Yong Sik; Park, Hwa Soon; Kim, Yeong Hwan; Won, Tae Yeon; Lee, Sang Lae

1994-01-01

Intergranular corrosion behavior of heat affected zone(HAZ) has been investigated for Ti-stabilized austenitic stainless steel AISI 321. It was observed that grain boundaries at HAZ of the steel with Ti/C ratio of 6.2 were corroded significantly after sensitization heat treatment. The increase of the Ti/C ratio up to 9.6 results in the evident decrease of intergranular corrosion. Weld simulation and intergranular corrosion test in 65% HNO 3 was performed. Influence of various thermal cycles on the intergranular corrosion was investigated. These results are discussed in terms of the behavior of TiC and Cr 23 C 6 precipitates

Hot coiled steel strip with elevated niobium content for pipelines and its weldability

International Nuclear Information System (INIS)

Brozda, J.; Zeman, M.

2010-01-01

Examinations and tests have been performed on thermomechanically rolled and hot coiled 14 mm thick steel strips with a low carbon and elevated niobium content, assigned for the production of pipelines. There were examined basic mechanical properties of the steels, brittle fracture resistance of the parent material and simulated HAZ's, susceptibility to cold cracking as well as properties of MMA and GMA welded joints. It was found that the tested steels are characterized by a good weldability, are not prone to cold cracking, have a low brittle fracture transition temperature and the HAZ of welded joints shows a sufficient high brittle fracture resistance. (authors)

Charpy impact test results of ferritic alloys from the HFIR[High Flux Isotope Reactor]-MFE-RB2 test

International Nuclear Information System (INIS)

Hu, W.L.; Gelles, D.S.

1987-03-01

Miniature Charpy specimens of HT-9 in base metal, weld metal and heat affected zone (HAZ) metal conditions, and 9Cr-1Mo in base metal and weld metal conditions have been tested following irradiation in HFIR-MFE-RB2 at 55 0 C to ≅10 dpa. All specimen conditions have degraded properties (both DBTT and USE) in comparison with specimens irradiated to lower dose. 9Cr-Mo degraded more than HT-9 and weld metal performed worse than base metal which performed worse than HAZ material. Property degradation was approximately linear as a function of dose, indicating that degradation response had not saturated by 10 dpa

Effects of strength mis-matching on the fracture behavior of nuclear pressure steel A508-III welded joint

Energy Technology Data Exchange (ETDEWEB)

Zhu Zhengqiang [School of Material Science and Technology, Shanghai Jiaotong University, 1954 Huashan Road, Shanghai 200030 (China)]. E-mail: zhuzhq01@sjtu.edu.cn; Jing Hongyang [School of Material Science and Technology, Tianjin University, Tianjin 300072 (China); Ge Jingguo [School of Material Science and Technology, Shanghai Jiaotong University, 1954 Huashan Road, Shanghai 200030 (China); Chen Ligong [School of Material Science and Technology, Shanghai Jiaotong University, 1954 Huashan Road, Shanghai 200030 (China)

2005-01-15

In this paper, according to the nuclear pressure steel A508-III, the effect of strength mis-matching on the fracture behavior was analyzed by fracture mechanics test and the crack tip stress field of three-point bend specimen was analyzed by using finite element analysis method (FEM). The fracture of heat-affected zone (HAZ) was emphasized especially. The results of FEM show that if the under-matching weld was used, the opening stress and stress triaxiality in the vicinity of crack tip would increase for weld-crack specimen, and would reduce for HAZ-crack specimen. This tendency was confirmed by the test results.

Süt Proteinlerinin RP-HPLC ile Saptanması (İngilizce

Directory of Open Access Journals (Sweden)

Zerrin Yüksel

2015-02-01

Full Text Available Bu çalışmada, κ-, α- and β-kazein ile α-laktalbumin and β-laktoglobulin, bir RP kolonunun kullanıldığı HPLC-UV ile basit ve hızlı bir yöntem geliştirilerek saptanmıştır. Gradient elüsyonu, 1 ml/dk akış hızında ve 25 oC sıcaklıkta iki çözücü karışımı kullanılarak yürütülmüştür. A çözücüsü asetonitril: su:trifloroasetik asit (100:900:1 ve B çözücüsü asetonitril: su: trifloroasetik asit (100:900:1 karışımlarından oluşmaktadır. Akış, bir UV dedektörü kullanılarak 220 nm’de kaydedilmiştir. Farklı yöntemler kullanılarak RP-HPLC analizi için hazırlanan örneklerde, süt proteinlerine ait farklı kromatografik profiller elde edilmiştir. Diğer örnek hazırlama yöntemlerine kıyasla, enjeksiyondan önce belirtilen oranlarda A ve B çözücülerinin kullanıldığı örnek hazırlama yöntemi ile separasyonun daha keskin ve efektif olduğu ortaya konulmuştur. Bu çalışmada ortaya konulan örnek hazırlama tekniği ve elusyon pratiği ile, süt proteinlerinin analizi basit, hızlı ve duyarlı bir şekilde gerçekleştirilmiştir.

Height, weight, and education achievement in rural Peru.

Science.gov (United States)

Cueto, Santiago

2005-06-01

The education system in Peru and many other developing countries faces several challenges, including improving education achievement and increasing education enrollment in high school. It is clear from several indicators that rural students have lower education outcomes than do urban students. In this study we used cross-sectional and longitudinal analysis to determine the relationship between height-for-age z-scores (HAZ), weight-for-age z-scores (WAZ), body-mass index (BMI), and education outcomes. The sample was composed of students from 20 elementary public schools in two rural zones in Peru. The descriptive results show that there was no association between any of the anthropometric variables and achievement (mathematics and reading comprehension) or advancing to high school without repeating a grade. However, BMI was associated with dropping out of school: children with higher BMI in 1998 were more likely to be out of school by 2001. The hierarchical multivariate analysis also showed no relationship between anthropometry and achievement at the individual level, but students with relatively higher HAZ in 1998 were more likely to be drop-outs by 2001. These results contradict prior findings that showed a positive association between anthropometric variables (especially HAZ) and education achievement. The results might be explained by the fact that the study was carried out at very poor sites, at altitudes between 3000 and 3500 meters above sea level. The scarce studies about development in high altitudes suggest that the patterns for height and weight for children and adolescents are different than at sea level. Another possible explanation has to do with the fact that in the contexts studied, children who are perceived as relatively heavier (BMI) or taller (HAZ) might be expected to be out of school and start working (in fact, this was the primary reason given by children for dropping out of school).

Is Exposure to Poultry Harmful to Child Nutrition? An Observational Analysis for Rural Ethiopia.

Science.gov (United States)

Headey, Derek; Hirvonen, Kalle

2016-01-01

Although strategic thinking on water, sanitation and hygiene (WASH) has prioritized reducing exposure to human feces in order to limit diarrheal infections, recent research suggests that elevated exposure to livestock-particularly poultry and poultry feces-may be an important risk factor for diarrhea, environmental enteric disorder (EED) and respiratory infections, all of which may seriously retard linear growth in young children. Yet a very different literature on nutrition-sensitive agriculture suggests that livestock ownership is highly beneficial for child growth outcomes through its importance for increasing consumption of nutrient-rich animal sourced foods, such as eggs. Together, these two literatures suggest that the net nutritional benefit of poultry ownership is particularly ambiguous and potentially mediated by whether or not children are highly exposed to poultry. We test this novel hypothesis using a large agricultural survey of rural Ethiopian households that includes measures of child height-for-age Z-scores (HAZ), ownership of poultry and other types of livestock, and an indicator of whether livestock are kept within the main household dwelling overnight. We used least squares regression analysis to estimate unadjusted and adjusted models that control for a wide range of potentially confounding factors. We find that while poultry ownership is positively associated with child HAZ [β = 0.291, s.e. = 0.094], the practice of corralling poultry in the household dwelling overnight is negatively associated with HAZ [β = -0.250, s.e. = 0.118]. Moreover, we find no negative associations between HAZ and corralling other livestock species indoors. These results suggest that while poultry ownership can be beneficial to child growth, overly close exposure to poultry poses a concurrent risk factor for undernutrition, most likely because of increased risk of infection.

Effect of Alloy 625 Buffer Layer on Hardfacing of Modified 9Cr-1Mo Steel Using Nickel Base Hardfacing Alloy

Science.gov (United States)

Chakraborty, Gopa; Das, C. R.; Albert, S. K.; Bhaduri, A. K.; Murugesan, S.; Dasgupta, Arup

2016-04-01

Dashpot piston, made up of modified 9Cr-1Mo steel, is a part of diverse safety rod used for safe shutdown of a nuclear reactor. This component was hardfaced using nickel base AWS ER NiCr-B alloy and extensive cracking was experienced during direct deposition of this alloy on dashpot piston. Cracking reduced considerably and the component was successfully hardfaced by application of Inconel 625 as buffer layer prior to hardface deposition. Hence, a separate study was undertaken to investigate the role of buffer layer in reducing the cracking and on the microstructure of the hardfaced deposit. Results indicate that in the direct deposition of hardfacing alloy on modified 9Cr-1Mo steel, both heat-affected zone (HAZ) formed and the deposit layer are hard making the thickness of the hard layer formed equal to combined thickness of both HAZ and deposit. This hard layer is unable to absorb thermal stresses resulting in the cracking of the deposit. By providing a buffer layer of Alloy 625 followed by a post-weld heat treatment, HAZ formed in the modified 9Cr-1Mo steel is effectively tempered, and HAZ formed during the subsequent deposition of the hardfacing alloy over the Alloy 625 buffer layer is almost completely confined to Alloy 625, which does not harden. This reduces the cracking susceptibility of the deposit. Further, unlike in the case of direct deposition on modified 9Cr-1Mo steel, dilution of the deposit by Ni-base buffer layer does not alter the hardness of the deposit and desired hardness on the deposit surface could be achieved even with lower thickness of the deposit. This gives an option for reducing the recommended thickness of the deposit, which can also reduce the risk of cracking.

Study of stress relief cracking in titanium stabilized austenitic stainless steel; Etude de la fissuration differee par relaxation d'un acier inoxydable austenitique stabilise au titane

Energy Technology Data Exchange (ETDEWEB)

Chabaud-Reytier, M

1999-07-01

The heat affected zone (HAZ) of titanium stabilised austenitic stainless steel welds (AISI 321) may exhibit a serious form of intercrystalline cracking during service at high temperature. This type of cracking, called 'stress relief cracking', is known to be due to work hardening but also to ageing: a fine and abundant intragranular Ti(C,N) precipitation appears near the fusion line and modifies the mechanical behaviour of the HAZ. This study aims to better know the accused mechanism and to succeed in estimating the risk of such cracking in welded junctions of 321 stainless steel. To analyse this embrittlement mechanism, and to assess the lifetime of real components, different HAZ are simulated by heat treatments applied to the base material which is submitted to various cold rolling and ageing conditions in order to reproduce the HAZ microstructure. Then, we study the effects of work hardening and ageing on the titanium carbide precipitation, on the mechanical (tensile and creep) behaviour of the resulting material and on its stress relief cracking sensitivity. It is shown that work hardening is the main parameter of the mechanism and that ageing do not favour crack initiation although it leads to titanium carbide precipitation. The role of this precipitation is also discussed. Moreover, a creep damage model is identified by a local approach to fracture. Materials sensitive to stress relief cracking are selected. Then, creep tests are carried out on notched bars in order to quantify the intergranular damage of these different materials; afterwards, these measurements are combined with calculated mechanical fields. Finally, it is shown that the model gives good results to assess crack initiation for a compact tension (CT) specimen during relaxation tests, as well as for a notched tubular specimen tested at 600 deg. C under a steady torque. (author)

Evaluation of a residential nutrition rehabilitation center in rural Bolivia: short-term effectiveness and follow-up results.

Science.gov (United States)

Forney, Kristen M; Polansky, Lauren S; Rebolledo, Paulina A; Huamani, Katherine Foy; Mues, Katherine E; Ramakrishnan, Usha; Leon, Juan S

2014-06-01

Nutrition rehabilitation centers (NRCs) have shown mixed results in reducing morbidity and mortality among undernourished children in the developing world. Follow-up on children after leaving these programs remains undocumented. To assess the nutritional improvement of children attending the Centro de Rehabilitación Infantil Nutricional (CRIN), a residential NRC in rural Bolivia, from entrance to exit and to a household follow-up visit 1 month to 6 years later, and to identify factors associated with nutritional improvement. A retrospective analysis was conducted of clinical records collected by CRIN staff from 135 children under 3 years of age attending CRIN in rural Cochabamba, Bolivia, from 2003 to 2009, and of clinical records of household follow-up measurements on a subset of 26 children that were taken between 1 month and 6 years postexit. Nutritional status was evaluated by calculating z-scores for weight-for-height (WHZ), weight-for-age (WAZ), and height-for-age (HAZ). Children with z-scores < -2 were considered to be wasted, underweight, or stunted, respectively. The prevalence of wasting decreased significantly, while the prevalence of stunting did not change significantly between entrance and exit from the program. From entrance to exit, the mean changes in WHZ (0.79) and WAZ (1.08) were statistically significant, while the mean change in HAZ (-0.02) was not significant. Linear regression analysis suggested that nutritional status and diarrhea at entrance had the greatest effect on WHZ and HAZ changes between entrance and exit. Children maintained their nutritional gains from the program between exit and follow-up and showed statistically significant improvement in WAZ (but not HAZ). CRIN is effective at rehabilitating nutritional deficits associated with wasting, but not those associated with stunting.

Simulation investigation of thermal phase transformation and residual stress in single pulse EDM of Ti-6Al-4V

Science.gov (United States)

Tang, Jiajing; Yang, Xiaodong

2018-04-01

The thermal phase transformation and residual stress are ineluctable in the electrical discharge machining (EDM) process, and they will greatly affect the working performances of the machined surface. This paper presents a simulation study on the thermal phase transformation and residual stress in single-pulse EDM of Ti-6Al-4V, which is the most popular titanium alloy in fields such as aircraft engine and some other leading industries. A multi-physics model including thermal, hydraulic, metallography and structural mechanics was developed. Based on the proposed model, the thickness and metallographic structure of the recast layer and heat affected layer (HAZ) were investigated. The distribution and characteristics of residual stress around the discharge crater were obtained. The recast layer and HAZ at the center of crater are found to be the thinnest, and their thicknesses gradually increase approaching the periphery of the crater. The recast layer undergoes a complete α‧ (martensitic) transformation, while the HAZ is mainly composed by the α  +  β  +  α‧ three-phase microstructure. Along the depth direction of crater, the Von Mises stress increases first and then decreases, reaching its maximal value near the interface of recast layer and HAZ. In the recast layer, both compressive stress component and tensile stress component are observed. ANOVA results showed that the influence of discharge current on maximal tensile stress is more significant than that of pulse duration, while the pulse duration has more significant influence on average thickness of the recast layer and the depth location of the maximal tensile stress. The works conducted in this study will help to evaluate the quality and integrity of EDMed surface, especially when the non-destructive testing is difficult to achieve.

Stunted at 10 Years. Linear Growth Trajectories and Stunting from Birth to Pre-Adolescence in a Rural Bangladeshi Cohort.

Directory of Open Access Journals (Sweden)

Pernilla Svefors

Full Text Available Few studies in low-income settings analyse linear growth trajectories from foetal life to pre-adolescence. The aim of this study is to describe linear growth and stunting from birth to 10 years in rural Bangladesh and to analyse whether maternal and environmental determinants at conception are associated with linear growth throughout childhood and stunting at 10 years.Pregnant women participating in the MINIMat trial were identified in early pregnancy and a birth cohort (n = 1054 was followed with 19 growth measurements from birth to 10 years. Analyses of baseline predictors and mean height-for-age Z-scores (HAZ over time were modelled using GLMM. Logistic regression analysis was used to investigate the associations between baseline predictors and stunting (HAZ<-2 at 10 years. HAZ decreased to 2 years, followed by an increase up to 10 years, while the average height-for-age difference in cm (HAD to the WHO reference median continued to increase up to 10 years. Prevalence of stunting was highest at 2 years (50% decreasing to 29% at 10 years. Maternal height, maternal educational level and season of conception were all independent predictors of HAZ from birth to pre-adolescence (p<0.001 and stunting at 10 years. The highest probability to be stunted at 10 years was for children born by short mothers (<147.5 cm (ORadj 2.93, 95% CI: 2.06-4.20, mothers with no education (ORadj 1.74, 95% CI 1.17-2.81 or those conceived in the pre-monsoon season (ORadj 1.94, 95% CI 1.37-2.77.Height growth trajectories and prevalence of stunting in pre-adolescence showed strong intergenerational associations, social differentials, and environmental influence from foetal life. Targeting women before and during pregnancy is needed for the prevention of impaired child growth.

Study of stress relief cracking in titanium stabilized austenitic stainless steel

International Nuclear Information System (INIS)

Chabaud-Reytier, M.

1999-01-01

The heat affected zone (HAZ) of titanium stabilised austenitic stainless steel welds (AISI 321) may exhibit a serious form of intercrystalline cracking during service at high temperature. This type of cracking, called 'stress relief cracking', is known to be due to work hardening but also to ageing: a fine and abundant intragranular Ti(C,N) precipitation appears near the fusion line and modifies the mechanical behaviour of the HAZ. This study aims to better know the accused mechanism and to succeed in estimating the risk of such cracking in welded junctions of 321 stainless steel. To analyse this embrittlement mechanism, and to assess the lifetime of real components, different HAZ are simulated by heat treatments applied to the base material which is submitted to various cold rolling and ageing conditions in order to reproduce the HAZ microstructure. Then, we study the effects of work hardening and ageing on the titanium carbide precipitation, on the mechanical (tensile and creep) behaviour of the resulting material and on its stress relief cracking sensitivity. It is shown that work hardening is the main parameter of the mechanism and that ageing do not favour crack initiation although it leads to titanium carbide precipitation. The role of this precipitation is also discussed. Moreover, a creep damage model is identified by a local approach to fracture. Materials sensitive to stress relief cracking are selected. Then, creep tests are carried out on notched bars in order to quantify the intergranular damage of these different materials; afterwards, these measurements are combined with calculated mechanical fields. Finally, it is shown that the model gives good results to assess crack initiation for a compact tension (CT) specimen during relaxation tests, as well as for a notched tubular specimen tested at 600 deg. C under a steady torque. (author)

Microstructure-property relationship in microalloyed high-strength steel welds

International Nuclear Information System (INIS)

Zhang, Lei

2017-01-01

High-strength steels are favoured materials in the industry for production of safe and sustainable structures. The main technology used for joining the components of such steel is fusion welding. Steel alloy design concepts combined with advanced processing technologies have been extensively investigated during the development of High-Strength Low-Alloy (HSLA) steels. However, very few studies have addressed the issue of how various alloy designs, even with limited microalloy addition, can influence the properties of high-strength steel welds. In high-strength steel welding practices, the challenges regarding microstructure evolution and the resulting mechanical properties variation, are of great interest. The main focus is the debate regarding the role of microalloy elements on phase transformation and weld performance. Limited Heat Affected Zone (HAZ) softening and limited austenite grain coarsening are significant design essentials, but the primary goal is to ensure excellent toughness and tensile properties in the steel weld. To achieve this purpose, microalloy elements such as Ti, Nb, or V were intentionally added to modern high-strength steels. The focus of this work was to understand the mechanical properties of HSLA steels resulting from differences in alloy design after joining by modern welding processes. To begin, three microalloyed S690QL steels (Nb, Ti, and Ti+V addition) were investigated. Optical microscopy confirmed that similar mixtures of tempered bainite and martensite predominated the parent microstructure in the three steels, different types of coarse microalloy precipitates were also visible. These precipitates were analysed by using a thermodynamic-based software and then identified by Transmission Electron Microscopy (TEM). Results of mechanical testing revealed that all three steels performed above the standard toughness and tensile strength values, but with varied yielding phenomena. During the welding operation, each of the three steels

Microstructure-property relationship in microalloyed high-strength steel welds

Energy Technology Data Exchange (ETDEWEB)

Zhang, Lei

2017-04-01

High-strength steels are favoured materials in the industry for production of safe and sustainable structures. The main technology used for joining the components of such steel is fusion welding. Steel alloy design concepts combined with advanced processing technologies have been extensively investigated during the development of High-Strength Low-Alloy (HSLA) steels. However, very few studies have addressed the issue of how various alloy designs, even with limited microalloy addition, can influence the properties of high-strength steel welds. In high-strength steel welding practices, the challenges regarding microstructure evolution and the resulting mechanical properties variation, are of great interest. The main focus is the debate regarding the role of microalloy elements on phase transformation and weld performance. Limited Heat Affected Zone (HAZ) softening and limited austenite grain coarsening are significant design essentials, but the primary goal is to ensure excellent toughness and tensile properties in the steel weld. To achieve this purpose, microalloy elements such as Ti, Nb, or V were intentionally added to modern high-strength steels. The focus of this work was to understand the mechanical properties of HSLA steels resulting from differences in alloy design after joining by modern welding processes. To begin, three microalloyed S690QL steels (Nb, Ti, and Ti+V addition) were investigated. Optical microscopy confirmed that similar mixtures of tempered bainite and martensite predominated the parent microstructure in the three steels, different types of coarse microalloy precipitates were also visible. These precipitates were analysed by using a thermodynamic-based software and then identified by Transmission Electron Microscopy (TEM). Results of mechanical testing revealed that all three steels performed above the standard toughness and tensile strength values, but with varied yielding phenomena. During the welding operation, each of the three steels

Two food-assisted maternal and child health nutrition programs helped mitigate the impact of economic hardship on child stunting in Haiti.

Science.gov (United States)

Donegan, Shannon; Maluccio, John A; Myers, Caitlin K; Menon, Purnima; Ruel, Marie T; Habicht, Jean-Pierre

2010-06-01

Rigorous evaluations of food-assisted maternal and child health and nutrition programs are stymied by the ethics of randomizing recipients to a control treatment. Using nonexperimental matching methods, we evaluated the effect of 2 such programs on child linear growth in Haiti. The 2 well-implemented programs offered the same services (food assistance, behavior change communication, and preventive health services) to pregnant and lactating women and young children. They differed in that one (the preventive program) used blanket targeting of all children 6-23 mo, whereas the other (the recuperative program) targeted underweight (weight-for-age Z score effects on height-for-age Z scores (HAZ) and stunting (HAZ growth in a time of deteriorating economic circumstances.

Microstructure development of welding joints in high Cr ferritic steels

Energy Technology Data Exchange (ETDEWEB)

Kubushiro, Keiji; Takahashi, Satoshi; Morishima, Keiko [IHI Corporation (Japan). Research Lab.

2010-07-01

Creep failure in high Cr ferritic steels welding joints are Type IV failure. Type IV-failure was ruptured in fine grained region of heat affected zone, microstructure and phase transformation process at welding in fine grained region were very important to clarify. Microstructure difference of heat affected zone was investigated in Gr.91, Gr.92, Gr.122 welding joint. The fraction of 60 degree block boundary, packet boundary, random boundary (including prior gamma boundary) length was compared in three ferritic steels by EBSP(Electron Backscatter Diffraction Pattern) analysis. HAZ was almost fully martensite phase in Gr.122 weld joint. On the other hand, HAZ in Gr.91 welding joint were some equiaxial grain and martensite structure. (orig.)

Enhancement of the quality of the reactor pressure vessel used in light water power plants by advanced material fabrication and testing technoligies

International Nuclear Information System (INIS)

Kussmaul, K.; Ewald, J.

1977-01-01

The fracture safe assessment of nuclear pressure vessels (RPV) is based upon: (i) an adequate stress analysis, (ii) reliable material characteristics, (iii) acceptable defects sizes. There may arise problems which are related to the inhomogeneity, low toughness and crack phenomena sometimes observed in the base material and heat affected zone (HAZ). Due to this it is difficult and in some respects even impossible to measure the decisive values of (fracture-) toughness and defects. Apart from the significance of those facts for existing RPVs, all efforts were directed to provide a steel which should be non-susceptible to embrittlement and/or cracking in the HAZ and simultaneously yielding in a higher upper shelf toughness of base and HAZ material. These objections were pursued in cooperation with manufacturers, vendors and inspection authorities by the following activities. (i) Detailed investigations to obtain information on: occurrence and size of inhomogeneities and defects, especially stress relief cracking (SCR), toughness properties adjacent to defects; (ii) improvement of: chemical composition, steel making processes, welding procedures, optimum temperature cycle and level for stress relief heat-treatment. In order to solve these tasks it was necessary to develop additional tools and to correlate all partial results which were newly elaborated. (Auth.)

Linear growth and child development in low- and middle-income countries: a meta-analysis.

Science.gov (United States)

Sudfeld, Christopher R; McCoy, Dana Charles; Danaei, Goodarz; Fink, Günther; Ezzati, Majid; Andrews, Kathryn G; Fawzi, Wafaie W

2015-05-01

The initial years of life are critical for physical growth and broader cognitive, motor, and socioemotional development, but the magnitude of the link between these processes remains unclear. Our objective was to produce quantitative estimates of the cross-sectional and prospective association of height-for-age z score (HAZ) with child development. Observational studies conducted in low- and middle-income countries (LMICs) presenting data on the relationship of linear growth with any measure of child development among children children ≤ 2 years old was +0.24 (95% confidence interval [CI], 0.14-0.33; I(2) = 53%) and +0.09 for children > 2 years old (95% CI, 0.05-0.12; I(2) = 78%). Prospectively, each unit increase in HAZ for children ≤ 2 years old was associated with a +0.22-SD increase in cognition at 5 to 11 years after multivariate adjustment (95% CI, 0.17-0.27; I(2) = 0%). HAZ was also significantly associated with earlier walking age and better motor scores (P development. Effective interventions that reduce linear growth restriction may improve developmental outcomes; however, integration with environmental, educational, and stimulation interventions may produce larger positive effects. Copyright © 2015 by the American Academy of Pediatrics.

Dietary diversity and nutritional status among children in rural Burkina Faso.

Science.gov (United States)

Sié, Ali; Tapsoba, Charlemagne; Dah, Clarisse; Ouermi, Lucienne; Zabre, Pascal; Bärnighausen, Till; Arzika, Ahmed M; Lebas, Elodie; Snyder, Blake M; Moe, Caitlin; Keenan, Jeremy D; Oldenburg, Catherine E

2018-05-01

Burkina Faso has a seasonal malnutrition pattern, with higher malnutrition prevalence during the rainy season when crop yields are low. We investigated the association between dietary diversity and nutritional status among children aged 6-59 mo during the low crop yield season in rural Burkina Faso to assess the role of dietary diversity during the lean season on childhood nutritional status. Caregivers reported the dietary diversity of the past 7 d, consisting of 11 food groups, summed into a scale. Anthropometric measurements were taken from all children. Height-for-age (HAZ), weight-for-height (WHZ) and weight-for-age (WAZ) z-scores were calculated based on 2006 WHO standards. Stunting, wasting and underweight were defined as HAZ, WHZ and WAZ indices and dietary diversity. Of 251 children enrolled in the study, 20.6% were stunted, 10.0% wasted and 13.9% underweight. Greater dietary diversity was associated with greater HAZ (SD 0.14, 95% CI 0.04 to 0.25) among all children. There was no association between dietary diversity and wasting or mid-upper arm circumference in this study. Increasing dietary diversity may be an approach to reduce the burden of stunting and chronic malnutrition among young children in regions with seasonal food insecurity.

Hazardous materials package performance regulations

International Nuclear Information System (INIS)

Russell, N.A.; Glass, R.E.; McClure, J.D.; Finley, N.C.

1993-01-01

Two regulatory philosophies, one based on 'specification' packaging standards and the other based on 'performance' packaging standards, currently define the hazmat packaging certification process. A main concern when setting performance standards is determining the appropriate standards necessary to assure adequate public protection. This paper discusses a Hazmat Packaging Performance Evaluation (HPPE) project being conducted at Sandia National Laboratories for the U.S. Department of Transportation Research and Special Programs Administration. In this project, the current bulk packagings (larger than 2000 gallons) for transporting Materials Extremely Toxic By Inhalation (METBI) are being evaluated and performance standards will be recommended. A computer software system, HazCon, has been developed which can calculate the dispersion of dense, neutral, and buoyant gases. HazCon also has a database of thermodynamic and toxicity data for the METBI materials, a user-friendly menu-driven format for creating input data sets for calculating dispersion of the METBI in the event of an accidental release, and a link between the METBI database and the dense gas dispersion code (which requires thermodynamic properties). The primary output of HazCon is a listing of mass concentrations of the released material at distances downwind from the release point. (J.P.N.)

IASCC susceptibility under BWR conditions of welded 304 and 347 stainless steels

Energy Technology Data Exchange (ETDEWEB)

Castano, M.L. [CIEMAT, Complutense 22, 28040 Madrid (Spain); Schaaf, B. van der [NRG, Petten (Netherlands); Roth, A. [Framatome ANP, Erlangen (Germany); Ohms, C. [JRC-IE, Petten (Netherlands); Gavillet, D. [PSI, Villigen (Switzerland); Dyck, S. van [SCK - CEN, Mol (Belgium)

2004-07-01

In-service cracking of Boiling Water Reactors (BWR) and Pressurized Water Reactors (PWR) internal components has been attributed to Irradiation Assisted Stress Corrosion Cracking (IASCC), a high temperature degradation process that austenitic stainless steels exhibit, when subjected to stress and exposed to relatively high fast neutron flux. Most of the cracking incidents in BWRs were associated to the heat-affected zone (HAZ) of welds. Although the maximum end-of- life dose for this structure is about 3 x 10{sup 20} n/cm{sup 2}, below the threshold fluence of 5 x 10{sup 20} n/cm{sup 2} (equivalent to {approx} 1 dpa) for IASCC in BWR of annealed materials, the influence of neutron irradiation in the weld and HAZ is still an open question. As a consequence of the welding process, residual stresses, microstructural and microchemical modifications are expected. In addition, exposure to neutron irradiation can induce variations in the material's characteristics that can modify the stress corrosion resistance of the welded components. While the IASCC susceptibility of base materials is being widely studied in many international projects, the specific conditions of irradiated weldments are rarely assessed. The INTERWELD project, partially financed by the 5. Framework program of the European Commission, was defined to elucidate neutron radiation induced changes in the HAZ of austenitic stainless steel welds that may promote intergranular cracking. To achieve this goal the evolution of residual stresses, microstructure, micro-chemistry, mechanical properties and the stress corrosion behaviour of irradiated materials are being evaluated. Fabrication of appropriate welds of 304 and 347 stainless steels, representative of core components, was performed. These weld materials were irradiated in the High Flux Reactor (HFR) in Petten to two neutron dose levels, i.e. 0.3 and 1 dpa. Complete characterization of the HAZ of both materials, before and after irradiation is

Pleurotus ostreatus Yetiştiriciliğinde Katkı Maddesi Olarak Mısır Silajının Kullanımı

Directory of Open Access Journals (Sweden)

Beyhan Kibar

2016-05-01

Full Text Available Bu çalışma Pleurotus ostreatus mantarı yetiştiriciliğinde mısır silajının katkı maddesi olarak kullanım durumunu belirlemek amacıyla yapılmıştır. Çalışmada buğday samanına farklı oranlarda (%5, 10, 15 ve 20 mısır silajı ilave edilerek hazırlanan yetiştirme ortamları, verim ve morfolojik özellikler bakımından kontrol ile (%95 buğday samanı+%5 buğday kepeği karşılaştırılmıştır. Yetiştirme ortamlarının hazırlanmasında kullanılan materyallerin her birinin başlangıçtaki ve hazırlanan yetiştirme ortamlarının sterilizasyondan sonraki pH, karbon (C ve azot (N miktarı, C:N oranı ve mineral madde (K, P, Mg, Zn, Fe ve Mn içerikleri tespit edilmiştir. Verim bakımından kontrol ve farklı oranlarda mısır silajı ilave edilerek hazırlanan yetiştirme ortamları arasındaki farklılık istatistiki olarak önemli (P<0.05, morfolojik özellikler (şapka uzunluğu, sap uzunluğu ve sap kalınlığı bakımından ise önemsiz bulunmuştur. En yüksek verim (220.13 g kg-1 ortam buğday samanına %10 oranında mısır silajının ilave edilmesiyle hazırlanan yetiştirme ortamından, en düşük verim (153.75 g kg-1 ortam ise kontrol ortamından elde edilmiştir. Mısır silajının P. ostreatus yetiştiriciliğinde buğday kepeğine alternatif iyi ve ucuz bir katkı maddesi olarak kullanılabileceği sonucuna varılmıştır.

Experimental study and modelling of high temperature creep flow and damage behaviour of 9Cr1Mo-NbV steel weldments

International Nuclear Information System (INIS)

Gaffard, V.

2004-12-01

experimentally confirmed in the present study. The evaluation of creep flow and damage behaviour of the weldment requires two types of investigations, namely, the determination of the effect of welding on creep strength of the material especially in the heat affected zone (HAZ), and the investigation of the effect of the mismatch in creep properties between the weld metal, the base metal and the HAZ. To do so, the microstructure of the weakest HAZ was first reproduced on bulk specimens. These specimens were used to experimentally investigate the creep flow and damage behaviour of the weakest HAZ microstructure. The results of experiments allowed to fit a creep model for the simulated HAZ derived from the one designed for the base metal. The integration of constitutive equations of base metal, weld metal and simulated HAZ in finite element calculations of the heterogeneous weldment allows to study the effect of mismatch on creep properties and finally to predict creep lifetime of 9Cr1Mo-NbV welded components. (author)

Experimental study and modelling of high temperature creep flow and damage behaviour of 9Cr1Mo-NbV steel weldments; Etude experimentale et modelisation, du comportement, de l'endommagement et de la rupture en fluage a haute temperature de joint soudes en acier 9Cr1Mo-NbV

Energy Technology Data Exchange (ETDEWEB)

Gaffard, V

2004-12-15

experimentally confirmed in the present study. The evaluation of creep flow and damage behaviour of the weldment requires two types of investigations, namely, the determination of the effect of welding on creep strength of the material especially in the heat affected zone (HAZ), and the investigation of the effect of the mismatch in creep properties between the weld metal, the base metal and the HAZ. To do so, the microstructure of the weakest HAZ was first reproduced on bulk specimens. These specimens were used to experimentally investigate the creep flow and damage behaviour of the weakest HAZ microstructure. The results of experiments allowed to fit a creep model for the simulated HAZ derived from the one designed for the base metal. The integration of constitutive equations of base metal, weld metal and simulated HAZ in finite element calculations of the heterogeneous weldment allows to study the effect of mismatch on creep properties and finally to predict creep lifetime of 9Cr1Mo-NbV welded components. (author)

Evaluation of weld joints properties of 60mm thick AISI 316L for fusion reactor vacuum vessel by TIG and EB welding processes

International Nuclear Information System (INIS)

Buddu, Ramesh Kutner

2016-01-01

The present paper is focussed on the NDT examination procedures, evaluated mechanical properties; microstructure details investigated on the different welding process of Multipass TIG process (64 passes) and electron beam welding (two pass) of the AISI SS316LN plates. The characterization of mechanical properties (Tensile, Bend, Hardness and Impact) and detailed microstructure analysis have been discussed in this paper. Mechanical properties in both conditions shown higher joint efficiencies. Bend tests shown the good quality of weld and ductility behavior of the joining process. Hardening is observed in both the samples for welded zone and HAZ compared to base metal. Impact fracture results revealed the poor toughness properties for the WZ compared to HAZ and BM samples in both the cases

Weldability and microstructural analysis of nuclear-grade austenitic stainless steels

International Nuclear Information System (INIS)

Lee, C.H.

1988-01-01

This study evaluated the hot-ductility response, and hot-cracking susceptibility (fusion-zone solidification cracking and HAZ liquation cracking) of modified nuclear-grade and standard austenitic stainless steels. Extensive microstructural characterization using state-of-the-art analytical electron microscopy (TEM and STEM) as well as SEM (EDAX) and OLM was performed to correlate the material behavior with metallurgical characteristics. In addition, studies of the effect of Si, N, and rare earth elements on hot-cracking susceptibility, significance of the ductility dip phenomena and backfilled solidification cracks were also performed. Furthermore, based on the metallurgical evaluation, the possible mechanisms involved in solidification cracking and HAZ liquation cracking of the modified alloys are proposed. Finally, the optimized chemical specifications and requirements for nuclear-grade stainless steels are also suggested

Influence of stress relieve heat treatment on fatigue crack propagation in structural steel resistant to atmospheric corrosion welded joints

Energy Technology Data Exchange (ETDEWEB)

Martins, Geraldo de Paula; Villela, Jefferson Jose; Rabello, Emerson Giovani [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)]. E-mails: gpm@cdtn.br; jjv@cdtn.br; egr@cdtn.br; Cimini Junior, Carlos Alberto[Universidade Federal de Minas Gerais (UFMG), Belo Horizonte, MG (Brazil). Dept. de Engenharia Mecanica]. E-mail: cimini@demet.ufmg.br; Godefroid, Leonardo Barbosa [Universidade Federal de Ouro Preto (UFOP), MG (Brazil). Dept. de Metalurgia]. E-mails: leonardo@demet.em.ufop.br

2007-07-01

In this work, the influence of stress relieve heat treatment (SRHT) on the fatigue crack propagation in USI-SAC 50 structural welded joints at the heat affected zone (HAZ) region was studied. Hardness measurements before and after the SRHT were made and crack propagation tests in specimens as welded (AW) and in specimens that were submitted to SRHT, which were accomplished. A reduction in hardness at the regions of HAZ and melted zone (MZ) after the SRHT were observed. It were also verified that the crack propagation rates (da/dN) versus DK on the specimens AW presented regions of retardation on the crack propagation rate, and in the specimens that were submitted to SRHT the crack propagation rate were homogeneous. (author)

Study of localized corrosion in aluminum alloys by the scanning reference electrode technique

Science.gov (United States)

Danford, M. D.

1995-01-01

Localized corrosion in 2219-T87 aluminum (Al) alloy, 2195 aluminum-lithium (Al-Li) alloy, and welded 2195 Al-Li alloy (4043 filler) have been investigated using the relatively new scanning reference electrode technique (SRET). Anodic sites are more frequent and of greater strength in the 2195 Al-Li alloy than in the 2219-T87 Al alloy, indicating a greater tendency toward pitting for the latter. However, the overall corrosion rates are about the same for these two alloys, as determined using the polarization resistance technique. In the welded 2195 Al-Li alloy, the weld bean is entirely cathodic, with rather strongly anodic heat affected zones (HAZ) bordering both sides, indicating a high probability of corrosion in the HAZ parallel to the weld bead.

Fatigue crack propagation behavior and acoustic emission characteristics of the heat affected zone of super duplex stainless steel

International Nuclear Information System (INIS)

Do, Jae Yoon; Kim, Jin Hwan; Ahn, Seok Hwan; Park, In Duck; Kang, Chang Yong; Nam, Ki Woo

2002-01-01

Because duplex stainless steel shows the good strength and corrosion resistance properties, the necessity of duplex stainless steel, which has long life in severe environments, has been increased with industrial development. The fatigue crack propagation behavior of Heat Affected Zone(HAZ) has been investigated in super duplex stainless steel. The fatigue crack propagation rate of HAZ of super duplex stainless steel was faster than that of base metal of super duplex stainless steel. We also analysed acoustic emission signals during the fatigue test with time-frequency analysis method. According to the results of time-frequency analysis, the frequency ranges of 200-400 kHz were obtained by striation and the frequency range of 500 kHz was obtained due to dimple and separate of inclusion

Flood Hazard Areas - High Risk

Data.gov (United States)

Department of Homeland Security — The S_Fld_Haz_Ar table contains information about the flood hazards within the study area. A spatial file with locational information also corresponds with this data...

A comparative study of multiple regression analysis and back ...

Indian Academy of Sciences (India)

Abhijit Sarkar

artificial neural network (ANN) models to predict weld bead geometry and HAZ width in submerged arc welding ... Keywords. Submerged arc welding (SAW); multi-regression analysis (MRA); artificial neural network ..... Degree of freedom.

Segregation behavior of phosphorus in the heat-affected zone of an A533B/A182 dissimilar weld joint before and after simulated thermal aging

International Nuclear Information System (INIS)

Zhai, Ziqing; Miyahara, Yuichi; Abe, Hiroshi; Watanabe, Yutaka

2014-01-01

Highlights: • Impacts of aging on P segregation in actual heat-affected zone were examined by 3D-APT. • Non-equilibrium segregation of P dominated in subsequent cooling after welding. • Equilibrium segregation of P prevailed in step-cooling heat treatment. • High enrichment of P at grain/packet boundaries occurred in CGHAZ and ICCGHAZ. • Level of P enrichment at precipitate/matrix interface seemed species-dependent. - Abstract: The segregation behavior of phosphorus (P) in the heat-affected zone (HAZ) of an A533B/A182 dissimilar weld joint before and after step cooling was investigated with atom probe tomography. At grain/packet boundaries, the final P segregation level consisted of non-equilibrium segregation that occurred during cooling after welding and post-weld heat treatment (PWHT) and equilibrium segregation that occurred during step cooling. In both processes, higher P coverage was observed in the coarse-grained and intercritically reheated coarse-grained HAZ than in the fine-grained HAZ and base material. The cooling after welding and PWHT seemed to have a pronounced impact on P segregation in the subsequent aging process. In addition, P segregation also occurred at the precipitate/matrix interfaces of cementite, Mo 2 C and Al–Si rich precipitates. The evolution of P coverage at these two types of sites suggested increasing risks of embrittlement with an increase in aging time

Impression creep behaviour of Mod. 9Cr-1Mo steel weld joints

International Nuclear Information System (INIS)

Ridhin Raj, V.R.; Kottda, Ravi Sankar; Kamaraj, M.; Maduraimuthu, V.M.; Vasudevan, M.

2016-01-01

P91 steel (9Cr-1Mo) steel is extensively used in power plants for super heater coils, headers and steam piping. The aim of the present work is to study the creep behaviour of different zones of A-TIG weld joint using impression creep technique and compare it with that of the TIG weld joint. P91 steel weld joints were made by A-TIG welding without using any filler material and multi-pass TIG welding is done using ER90S-B9 filler rods. Welds were subjected to post-weld heat treatment (PWHT). Impression creep tests were carried out at 650 °C on the base metal, weld metal and HAZ regions. Optical Microscope and TEM were used to correlate microstructures with observed creep rates. The FGHAZ showed significantly higher impression creep rate compared to that of the base metal and weld metal. Fine grain size and relatively coarser M 23 C 6 carbide particles are responsible for higher creep rate. The impression creep rate of A-TIG weld metal and coarse grain HAZ was found to be lower than that of base metal. This is attributed to the higher grain size in weld metal and coarse HAZ attributed to the higher grain size in weld metal and to the higher peak temperature observed during A-TIG welding. (author)

Microstructural Characteristics and m23c6 Precipitate Behavior of the Course-Grained Heat-Affected Zone of T23 Steel without Post-Weld Heat Treatment

Directory of Open Access Journals (Sweden)

Seong-Hyeong Lee

2018-03-01

Full Text Available The microstructural characteristics of a simulated heat-affected zone (HAZ in SA213-T23 (2.25Cr-1.6W steel used for boiler tubes employed in thermal power plants were investigated using nital, alkaline sodium picrate, and Murakami’s etchants. In order to investigate the microstructure formation process of the HAZ in the welding process, simulated HAZ specimens were fabricated at intervals of 100 °C for peak temperatures between 950 and 1350 °C, and the microstructural features and precipitate behavior at various peak temperatures were observed. The alkaline-sodium-picrate-etched microstructures exhibited a black dot or band, which was not observed in the natal-etched microstructure. As the temperature increased from 950 to 1350 °C, the black dot and band became wider and thicker. Experimental analyses using an electron probe micro-analyzer, electron backscatter diffraction, and transmission electron microscopy revealed the appearance of austenite in the black dot region at a peak temperature of 950 °C; its amount increased up to a peak temperature of 1050 °C and thereafter decreased as the peak temperature further increased. The amount of M23C6 decreased with an increase in peak temperature. Based on these results, we investigated the behaviors of austenite and M23C6 as functions of the peak temperature.

Development of the plant life management technology for RPV steels [ - Current status of surveillance test specimen reconstitution program -

International Nuclear Information System (INIS)

Kazunobu, Sakamoto; Eliichiro, Otsuka; Yoshiaki, Oka; Kosei, Taguchi; Michiyoshi, Yamamoto

2001-01-01

In order to develop the reconstitution technology to standardize surveillance test specimen reconstitution practices to deal with the extended service life of reactor pressure vessels, the Japan Power Engineering and Inspection Corporation (JAPEIC) has been carried out the project entrusted by the Ministry of International Trade and Industry (MITI). We focus on a correlation between the reduction of absorbed energy and the interaction of the heat affected zone (HAZ) and the plastic zone, to establish applicable reconstitution conditions for Charpy specimens. The relationship between the plastic zone width and the absorbed energy has been obtained by estimating the plastic zone width from the hardness distribution of the Charpy specimens. Impact tests of reconstituted specimens with 10 mm-length insert using the surface activated joining method were performed and the test results were compared to those obtained by the standard specimens. By comparing the length of insert material to the sum of HAZ width and plastic zone width, it is clear that the interaction causes the reduction of the absorbed energy. Hence, the applicable conditions of reconstituted Charpy specimens could be assessed by comparing the insert length to the sum of HAZ width and plastic zone width. Moreover the effects of the possible deviations from the standard shape and size specimens for the reconstituted specimens were studied. (authors)

Evaluation of mechanical properties of weldments for reduced activation ferritic/martensitic steel

Energy Technology Data Exchange (ETDEWEB)

Nakata, T. [Muroran Institute of Technology, Dept. of Materials Science and Engineeering, Muroran, Hokkaido (Japan); Tanigawa, H.; Ando, M. [Japan Atomic Energy Agency, Naga-gun, Ibaraki-ken (Japan); Komazaki, S.; Kohno, Y. [Muroran Institute of Technology, Muroran (Japan)

2007-07-01

Full text of publication follows: Reduced activation ferritic/martensitic steels are the first candidate material for fusion reactor, and will be used as the structural materials of ITER test blanket modules (TBM). TBM will be assembled by welding various parts, it is important to be clearly mechanical properties of weldments to qualify TBM structure. In this paper, unirradiated mechanical properties of weldments, which is consisted of weld metal, heat affected zone (HAZ) and base metal region, obtained from TIG and EB welded F82H IEA-heat were evaluated by tensile, Charpy impact and creep test. Charpy impact test revealed that impact properties of weld metal does not deteriorate compared with that of base metal. The creep tests were carried out at temperatures of 773-873 K and at stress levels of 130-280 MPa, with the specimens which include weld metal and HAZ region in the gage section. In these conditions, rupture time of weldments yield to about 100-1000 hours. In the high-stress range, creep lives of welded joint decreased about 40% of base metal. However, in the low-stress range, creep lives of welded joint decrease about 60 to 70% of base metal. The failure at fine grain HAZ region (Type IV failure) does not occur in these conditions. The mechanism of these properties deterioration will be discussed based on the detailed analyses on microstructure changes. (authors)

Nonviolent civil insecurity is negatively associated with subsequent height-for-age in children aged <5 y born between 1998 and 2014 in rural areas of Africa.

Science.gov (United States)

Darrouzet-Nardi, Amelia F

2017-02-01

Civil wars and wars between states have occurred less frequently since the start of the 21st century, but civil insecurity outside the contexts of official wars continues to plague many parts of the world. The nutritional consequences of civil insecurity may disproportionately affect children, especially if experienced during sensitive developmental periods. This study estimated the associations between localized nonviolent and violent civil insecurity during key child nutritional periods and subsequent height-for-age z scores (HAZs) in 145,948 children born between 1998 and 2014 in Africa and examined the type of place of residence as a mediating factor. A collection of 61 geo-referenced Demographic and Health Surveys implemented between 1998 and 2014 were merged with data from the high-resolution Armed Conflict Location and Event Data Project to construct a repeat cross-sectional database, which was analyzed by using a difference-in-differences model with maternal fixed-effects. Exposure to 1 nonviolent localized civil insecurity event (mean ± SD: 0.42 ± 1.87 events) during pregnancy for children living in rural areas was associated with a reduction of 0.01 SD in HAZ (P = 0.024). Exposure to 5 localized civil conflict fatalities (mean ± SD: 1.41 ± 10.21 fatalities) for children living in rural areas during the complementary feeding stage was associated with a 0.002-SD decrease in HAZ (P = 0.030). There were no measurable associations between civil insecurity and child heights in urban areas, even though children in urban areas experience more civil insecurity. Exposure to both violent and nonviolent civil insecurity had negative associations with subsequent HAZ, but only in rural areas. The associations found were small in magnitude but still meaningful from a child-development perspective, because these events do not necessarily occur in the context of official wars, they are often nonviolent, and they are endemic to the region. © 2017 American Society for

Impact of education and provision of complementary feeding on growth and morbidity in children less than 2 years of age in developing countries: a systematic review

Science.gov (United States)

2013-01-01

Background About one third of deaths in children less than 5 years of age are due to underlying undernutrition. According to an estimate, 19.4% of children on the effect of complementary feeding (CF) (fortified or unfortified, but not micronutrients alone) and education on CF on children less than 2 years of age in low and middle income countries (LMIC). Studies that delivered intervention for at least 6 months were included; however, studies in which intervention was given for supplementary and therapeutic purposes were excluded. Recommendations are made for input to the Lives Saved Tool (LiST) model by following standardized guidelines developed by Child Health Epidemiology Reference Group (CHERG). Results We included 16 studies in this review. Amongst these, 9 studies provided education on complementary feeding, 6 provided complementary feeding (with our without education) and 1 provided both as separate arms. Overall, education on CF alone significantly improved HAZ (SMD: 0.23; 95% CI: 0.09, 0.36), WAZ (SMD 0.16, 95% CI: 0.05, 0.27), and significantly reduced the rates of stunting (RR 0.71; 95% CI: 0.56, 0.91). While no significant impact were observed for height and weight gain. Based on the subgroup analysis; ten studies from food secure populations indicated education on CF had a significant impact on height gain, HAZ scores, and weight gain, however, stunting reduced non-significantly. In food insecure population, CF education alone significantly improved HAZ scores, WAZ scores and significantly reduced the rates of stunting, while CF provision with or without education improved HAZ and WAZ scores significantly. Conclusion Complementary feeding interventions have a potential to improve the nutritional status of children in developing countries. However, large scale high quality randomized controlled trials are required to assess the actual impact of this intervention on growth and morbidity in children 6-24 months of age. Education should be combined with

Characterization of complex carbide–silicide precipitates in a Ni–Cr–Mo–Fe–Si alloy modified by welding

Energy Technology Data Exchange (ETDEWEB)

Bhattacharyya, D., E-mail: dhb@ansto.gov.au; Davis, J.; Drew, M.; Harrison, R.P.; Edwards, L.

2015-07-15

Nickel based alloys of the type Hastelloy-N™ are ideal candidate materials for molten salt reactors, as well as for applications such as pressure vessels, due to their excellent resistance to creep, oxidation and corrosion. In this work, the authors have attempted to understand the effects of welding on the morphology, chemistry and crystal structure of the precipitates in the heat affected zone (HAZ) and the weld zone of a Ni–Cr–Mo–Fe–Si alloy similar to Hastelloy-N™ in composition, by using characterization techniques such as scanning and transmission electron microscopy. Two plates of a Ni–Cr–Mo–Fe–Si alloy GH-3535 were welded together using a TiG welding process without filler material to achieve a joint with a curved molten zone with dendritic structure. It is evident that the primary precipitates have melted in the HAZ and re-solidified in a eutectic-like morphology, with a chemistry and crystal structure only slightly different from the pre-existing precipitates, while the surrounding matrix grains remained unmelted, except for the zones immediately adjacent to the precipitates. In the molten zone, the primary precipitates were fully melted and dissolved in the matrix, and there was enrichment of Mo and Si in the dendrite boundaries after solidification, and re-precipitation of the complex carbides/silicides at some grain boundaries and triple points. The nature of the precipitates in the molten zone varied according to the local chemical composition. - Graphical abstract: Display Omitted - Highlights: • Ni-based alloy with Cr, Mo, Si, Fe and C was welded, examined with SEM, EBSD, and TEM. • Original Ni{sub 2}(Mo,Cr){sub 4}(Si,C) carbides changed from equiaxed to lamellar shape in HAZ. • Composition and crystal structure remained almost unchanged in HAZ. • Original carbides changed to lamellar Ni{sub 3}(Mo,Cr){sub 3}(Si,C) in some cases in weld metal. • Precipitates were mostly incoherent, but semi-coherent in some cases in weld

Characterization of complex carbide–silicide precipitates in a Ni–Cr–Mo–Fe–Si alloy modified by welding

International Nuclear Information System (INIS)

Bhattacharyya, D.; Davis, J.; Drew, M.; Harrison, R.P.; Edwards, L.

2015-01-01

Nickel based alloys of the type Hastelloy-N™ are ideal candidate materials for molten salt reactors, as well as for applications such as pressure vessels, due to their excellent resistance to creep, oxidation and corrosion. In this work, the authors have attempted to understand the effects of welding on the morphology, chemistry and crystal structure of the precipitates in the heat affected zone (HAZ) and the weld zone of a Ni–Cr–Mo–Fe–Si alloy similar to Hastelloy-N™ in composition, by using characterization techniques such as scanning and transmission electron microscopy. Two plates of a Ni–Cr–Mo–Fe–Si alloy GH-3535 were welded together using a TiG welding process without filler material to achieve a joint with a curved molten zone with dendritic structure. It is evident that the primary precipitates have melted in the HAZ and re-solidified in a eutectic-like morphology, with a chemistry and crystal structure only slightly different from the pre-existing precipitates, while the surrounding matrix grains remained unmelted, except for the zones immediately adjacent to the precipitates. In the molten zone, the primary precipitates were fully melted and dissolved in the matrix, and there was enrichment of Mo and Si in the dendrite boundaries after solidification, and re-precipitation of the complex carbides/silicides at some grain boundaries and triple points. The nature of the precipitates in the molten zone varied according to the local chemical composition. - Graphical abstract: Display Omitted - Highlights: • Ni-based alloy with Cr, Mo, Si, Fe and C was welded, examined with SEM, EBSD, and TEM. • Original Ni 2 (Mo,Cr) 4 (Si,C) carbides changed from equiaxed to lamellar shape in HAZ. • Composition and crystal structure remained almost unchanged in HAZ. • Original carbides changed to lamellar Ni 3 (Mo,Cr) 3 (Si,C) in some cases in weld metal. • Precipitates were mostly incoherent, but semi-coherent in some cases in weld metal

Crystallographic texture and microstructural changes in fusion welds of recrystallized Zry-4 rolled plates

International Nuclear Information System (INIS)

Moya Riffo, A.; Vicente Alvarez, M.A.; Santisteban, J.R.; Vizcaino, P.; Limandri, S.; Daymond, M.R.; Kerr, D.; Okasinski, J.; Almer, J.; Vogel, S.C.

2017-01-01

This work presents a detailed characterization of the microstructural and crystallographic texture changes observed in the transition region in a weld between two Zircaloy-4 cold rolled and recrystallized plates. The microstructural study was performed by optical microscopy under polarized light and scanning electron microscopy (SEM). Texture changes were characterized at different lengthscales: in the micrometric size, orientation imaging maps (OIM) were constructed by electron backscatter diffraction (EBSD), in the millimetre scale, high energy XRD experiments were done at the Advanced Photon Source (USA) and compared to neutron diffraction texture determinations performed in the HIPPO instrument at Los Alamos National Laboratory. In the heat affected zone (HAZ) we observed the development of Widmanstätten microstructures, typical of the α(hcp) to β(bcc) phase transformation. Associated with these changes a rotation of the c-poles is found in the HAZ and fusion zone. While the base material shows the typical texture of a cold rolled plate, with their c-poles pointing 35° apart from the normal direction of the plate in the normal-transversal line, in the HAZ, c-poles align along the transversal direction of the plate and then re-orient along different directions, all of these changes occurring within a lengthscale in the order of mm. The evolution of texture in this narrow region was captured by both OIM and XRD, and is consistent with previous measurements done by Neutron Diffraction in the HIPPO diffractometer at Los Alamos National Laboratory, USA. The microstructural and texture changes along the HAZ were interpreted as arising due to the effect of differences in the cooling rate and β grain size on the progress of the different α variants during transformation. Fast cooling rates and large β grains are associated to weak variant selection during the β−>α transformation, while slow cooling rates and fine β grains result in strong variant selection.

Crystallographic texture and microstructural changes in fusion welds of recrystallized Zry-4 rolled plates

Energy Technology Data Exchange (ETDEWEB)

Moya Riffo, A., E-mail: alvaromoya@cab.cnea.gov.ar [Neutron Physics Department, Centro Atómico Bariloche, CNEA-CONICET (Argentina); Vicente Alvarez, M.A.; Santisteban, J.R. [Neutron Physics Department, Centro Atómico Bariloche, CNEA-CONICET (Argentina); Vizcaino, P. [Zirconium Technology Department, Centro Atómico Ezeiza, CNEA-CONICET (Argentina); Limandri, S. [Facultad de Matemática, Astronomía y Física, Universidad Nacional de Córdoba (Argentina); Daymond, M.R.; Kerr, D. [Dept. Mechanical and Materials Engineering, Queen' s University, Kingston, Ontario (Canada); Okasinski, J.; Almer, J. [Advanced Photon Source, Argonne National Laboratory, Argonne (United States); Vogel, S.C. [Los Alamos Neutron Science Center, Los Alamos National Laboratory, Los Alamos, NM (United States)

2017-05-15

This work presents a detailed characterization of the microstructural and crystallographic texture changes observed in the transition region in a weld between two Zircaloy-4 cold rolled and recrystallized plates. The microstructural study was performed by optical microscopy under polarized light and scanning electron microscopy (SEM). Texture changes were characterized at different lengthscales: in the micrometric size, orientation imaging maps (OIM) were constructed by electron backscatter diffraction (EBSD), in the millimetre scale, high energy XRD experiments were done at the Advanced Photon Source (USA) and compared to neutron diffraction texture determinations performed in the HIPPO instrument at Los Alamos National Laboratory. In the heat affected zone (HAZ) we observed the development of Widmanstätten microstructures, typical of the α(hcp) to β(bcc) phase transformation. Associated with these changes a rotation of the c-poles is found in the HAZ and fusion zone. While the base material shows the typical texture of a cold rolled plate, with their c-poles pointing 35° apart from the normal direction of the plate in the normal-transversal line, in the HAZ, c-poles align along the transversal direction of the plate and then re-orient along different directions, all of these changes occurring within a lengthscale in the order of mm. The evolution of texture in this narrow region was captured by both OIM and XRD, and is consistent with previous measurements done by Neutron Diffraction in the HIPPO diffractometer at Los Alamos National Laboratory, USA. The microstructural and texture changes along the HAZ were interpreted as arising due to the effect of differences in the cooling rate and β grain size on the progress of the different α variants during transformation. Fast cooling rates and large β grains are associated to weak variant selection during the β−>α transformation, while slow cooling rates and fine β grains result in strong variant selection.

Improvement in the reliability of shells for light water reactors by manufacture from hollow ingots

International Nuclear Information System (INIS)

Bocquet, P.; Blondeau, R.; Poitrault, I.; Badeau, J.P.; Dumont, R.

1991-01-01

The problems associated to the segregation located at the inner surface and subsurface of heavy shell forgings used in nuclear light water reactors are presented. The effect of A segregation on cold or reheat cracking HAZ has conducted fabricators to use severe welding procedures with high preheat temperature and refining HAZ grain size sequences. For shells and rings, the hollow ingot as developed by CLI, with a good control of the location of the center line of segregation, is an excellent answer to these problems. The use of core shell forgings issued from this type of hollow ingots, free of segregation at the inner surface and subsurface area, contributes, by reducing the irradiation embrittlement effect, to increase the safety factor relatively to the risk of failure of the reactor. (orig.)

Microstructure evolution of electron beam welded Ti3Al-Nb joint

International Nuclear Information System (INIS)

Feng Jicai; Wu Huiqiang; He Jingshan; Zhang Bingang

2005-01-01

The microstructure evolution characterization in high containing Nb, low Al titanium aluminide alloy of electron beam welded joints was investigated by means of OM, SEM, XRD, TEM and microhardness analysis. The results indicated that the microstructure of the weld metal made with electron beam under the welding conditions employed in this work was predominantly metastable, retaining ordered β phase (namely B2 phase), and was independent of the welding parameters but independent of the size and the orientation of the weld solidification structures. As the heat input is decreased, the cellular structure zone is significantly reduced, and then the crystallizing morphology of fusion zone presented dendritically columnar structure. There existed grain growth coarsening in heat affected zone (HAZ) for insufficient polygonization. Both fusion zone (FZ) and the HAZ had higher microhardness than the base metal

Dynamic fracture toughness of ASME SA508 Class 2a ASME SA533 grade A Class 2 base and heat affected zone material and applicable weld metals

International Nuclear Information System (INIS)

Logsdon, W.A.; Begley, J.A.; Gottshall, C.L.

1978-03-01

The ASME Boiler and Pressure Vessel Code, Section III, Article G-2000, requires that dynamic fracture toughness data be developed for materials with specified minimum yield strengths greater than 50 ksi to provide verification and utilization of the ASME specified minimum reference toughness K/sub IR/ curve. In order to qualify ASME SA508 Class 2a and ASME SA533 Grade A Class 2 pressure vessel steels (minimum yield strengths equal 65 kip/in. 2 and 70 kip/in. 2 , respectively) per this requirement, dynamic fracture toughness tests were performed on these materials. All dynamic fracture toughness values of SA508 Class 2a base and HAZ material, SA533 Grade A Class 2 base and HAZ material, and applicable weld metals exceeded the ASME specified minimum reference toughness K/sub IR/ curve

Clinical features and lung function in HIV-infected children with ...

African Journals Online (AJOL)

and determine clinical predictors of poor lung function. Methods. ... 2 Department of Paediatrics and Child Health, Stellenbosch University, South Africa. 3 Menzies ... HAZ were classified as stunted.[15]. The ... Dental caries. 14/40 (35.0).

Desenvolvimento da ferrita delta na solda e ZTA resultante de soldagem plasma pulsada em um aço inoxidável supermartensítico Delta-ferrite development in weld and HAZ produced by pulsed plasma arc welding in a supermartensitic stainless steel

Directory of Open Access Journals (Sweden)

Sérgio L. Henke

2013-03-01

Full Text Available A ferrita delta é considerada uma fase indesejável na microestrutura dos aços inoxidáveis martensíticos haja vista a mesma poder influenciar no desempenho da resistência à fadiga, tenacidade e corrosão sob-tensão. Sendo assim, o objetivo deste trabalho foi investigar o efeito da soldagem plasma pulsada sobre a distribuição e quantidade de ferrita delta em um aço inoxidável supermartensítico. Para tal foram obtidos cordões por meio de fusão superficial sobre uma amostra de aço inoxidável supermartensítico de alta liga utilizando corrente pulsada e convencional. Em seguida foi efetuada a caracterização microestrutural, em especial da ferrita delta, via análises metalográficas por meio de microscopia óptica e eletrônica de varredura . Os experimentos revelaram que, para o mesmo aporte térmico, a pulsação de corrente promoveu a formação de ferrita delta na forma de bandas ao longo do cordão de solda e redução significativa desta fase na ZTA quando comparada à soldagem convencional.The objective of this study was to investigate the effect of pulsed plasma welding on the distribution and amount of delta ferrite which is considered an undesirable phase in a supermartensitic stainless steel. For such weld beads have been obtained by melting the surface of a sample of a high-alloy supermartensitic stainless steel using pulsed and conventional current. Microstructural characterization, especially of delta ferrite, was performed by metallographic analysis by means of optical microscopy and scanning electron microscopy. The experiments showed that for the same heat input, pulsed current promoted the formation of delta ferrite in the form of bands along the weld bead and caused a significant reduction of this phase in HAZ as compared to conventional welding.

30 CFR 47.91 - Exemptions from the HazCom standard.

Science.gov (United States)

2010-07-01

... products (such as flavors and fragrances) When intended for personal consumption or use. Radiation All ionizing or non-ionizing radiation, such as alpha or gamma, microwaves, or x-rays. Wood or wood products...

Influence of epicentral distance on local seismic response in Kolkata ...

Indian Academy of Sciences (India)

Corresponding author. e-mail: wkmohanty@gg.iitkgp.ernet.in. The influence of source and .... specific or site-specific contribution to the ground motion amplitudes ...... Accounting for site effects in probabilistic seismic haz- ard analyses of ...

TEA CO2 laser machining of CFRP composite

Science.gov (United States)

Salama, A.; Li, L.; Mativenga, P.; Whitehead, D.

2016-05-01

Carbon fibre-reinforced polymer (CFRP) composites have found wide applications in the aerospace, marine, sports and automotive industries owing to their lightweight and acceptable mechanical properties compared to the commonly used metallic materials. Machining of CFRP composites using lasers can be challenging due to inhomogeneity in the material properties and structures, which can lead to thermal damages during laser processing. In the previous studies, Nd:YAG, diode-pumped solid-state, CO2 (continuous wave), disc and fibre lasers were used in cutting CFRP composites and the control of damages such as the size of heat-affected zones (HAZs) remains a challenge. In this paper, a short-pulsed (8 μs) transversely excited atmospheric pressure CO2 laser was used, for the first time, to machine CFRP composites. The laser has high peak powers (up to 250 kW) and excellent absorption by both the carbon fibre and the epoxy binder. Design of experiment and statistical modelling, based on response surface methodology, was used to understand the interactions between the process parameters such as laser fluence, repetition rate and cutting speed and their effects on the cut quality characteristics including size of HAZ, machining depth and material removal rate (MRR). Based on this study, process parameter optimization was carried out to minimize the HAZ and maximize the MRR. A discussion is given on the potential applications and comparisons to other lasers in machining CFRP.

Tungsten Inert Gas and Friction Stir Welding Characteristics of 4-mm-Thick 2219-T87 Plates at Room Temperature and -196 °C

Science.gov (United States)

Lei, Xuefeng; Deng, Ying; Yin, Zhimin; Xu, Guofu

2014-06-01

2219-T87 aluminum alloy is widely used for fabricating liquid rocket propellant storage tank, due to its admirable cryogenic property. Welding is the dominant joining method in the manufacturing process of aerospace components. In this study, the tungsten inert gas welding and friction stir welding (FSW) characteristics of 4-mm-thick 2219-T87 alloy plate at room temperature (25 °C) and deep cryogenic temperature (-196 °C) were investigated by property measurements and microscopy methods. The studied 2219 base alloy exhibits a low strength plane anisotropy and excellent room temperature and cryogenic mechanical properties. The ultimate tensile strength values of TIG and FSW welding joints can reach 265 and 353 MPa at room temperature, and 342 and 438 MPa at -196 °C, respectively. The base metal consists of elongated deformed grains and many nano-scaled θ (Al2Cu) aging precipitates. Fusion zone and heat-affected zone (HAZ) of the TIG joint are characterized by coarsening dendritic grains and equiaxed recrystallized grains, respectively. The FSW-welded joint consists of the weld nugget zone, thermo-mechanically affected zone (TMAZ), and HAZ. In the weld nugget zone, a micro-scaled sub-grain structure is the main microstructure characteristic. The TMAZ and HAZ are both characterized by coarsened aging precipitates and elongated deformed grains. The excellent FSW welding properties are attributed to the preservation of the working structures and homogenous chemical compositions.

Alloy Design of Martensitic 9Cr-Boron Steel for A-USC Boiler at 650 °C — Beyond Grades 91, 92 and 122

Science.gov (United States)

Abe, Fujio; Tabuchi, M.; Tsukamoto, S.

Boundary hardening is shown to be the most important strengthening mechanism in creep of tempered martensitic 9% Cr steel base metal and welded joints at 650 °C. The enrichment of soluble boron near prior austenite grain boundaries (PAGBs) by the GB segregation is essential for the reduction of coarsening rate of M23C6 carbides near PAGBs, enhancing the boundary and sub-boundary hardening near PAGBs, and also for the change in α/γ transformation behavior in heat-affected-zone (HAZ) of welded joints during heating of welding, producing the same microstructure in HAZ as in the base metal. Excess addition of nitrogen to the 9Cr-boron steel promotes the formation of boron nitrides during normalizing heat treatment, which consumes most of soluble boron and degrades the creep strength. A NIMS 9Cr steel (MARBN; Martensitic 9Cr steel strengthened by boron and MX nitrides) with 120-150 ppm boron and 60-90 ppm nitrogen, where no boron nitride forms during normalizing heat treatment, exhibits not only much higher creep strength of base metal than Grades 91, 92 and 122 but also substantially no degradation in creep strength due to Type IV fracture in HAZ of welded joints at 650°C. The protective Cr2O3-rich scale forms on the surface of 9Cr steel by pre-oxidation treatment in Ar gas, which significantly improves the oxidation resistance in steam at 650°C.

Thermal and mechanical effect during rapid heating of astroloy for improving structural integrity

International Nuclear Information System (INIS)

Popoolaa, A.P.I.; Oluwasegun, K.M.; Olorunniwo, O.E.; Atanda, P.O.; Aigbodion, V.S.

2016-01-01

The behaviour of γ′ phase to thermal and mechanical effects during rapid heating of Astroloy(Turbine Disc alloy) a Powder metallurgy (PM) nickel base superalloy has been investigated. The thermo-mechanical affected zone (TMAZ) and heat affected zone (HAZ) microstructure of an inertia friction welded Astroloy were simulated using a Gleeble thermo-mechanical simulation system. Detailed microstructural examination of the simulated TMAZ and HAZ and those present in actual inertial friction welded specimens showed that γ′ particles persisted during rapid heating up to a temperature where the formation of liquid is thermodynamically favoured, and subsequently re-solidified eutectically. The result obtained showed that forging during the thermo-mechanical simulation significantly enhanced resistance to weld liquation cracking of the alloy. This is attributable to strain-induced rapid isothermal dissolution of the constitutional liquation products within 150 μm from the centre of the forged sample. This was not observed in purely thermally simulated samples. The microstructure within the TMAZ of the as-welded alloy is similar to the microstructure in the forged Gleeble specimens. - Highlights: • The behaviour of γ′ phase to thermal and mechanical effects during rapid heating of Astrology • The thermo-mechanical affected zone (TMAZ) and heat affected zone (HAZ). • significantly enhanced resistance to weld liquation cracking of the alloy. • This was not observed in purely thermally simulated samples. • The microstructure within the TMAZ of the as-welded alloy is similar to the microstructure in the forged Gleeble specimens.

Thermal and mechanical effect during rapid heating of astroloy for improving structural integrity

Energy Technology Data Exchange (ETDEWEB)

Popoolaa, A.P.I., E-mail: popoolaapi@tut.ac.za [Department of Chemical, Metallurgical and Materials Engineering, Tshwane University of Technology, Pretoria (South Africa); Oluwasegun, K.M. [Department of Materials Science and Engineering, Obafemi Awolowo University (Nigeria); Olorunniwo, O.E., E-mail: segun_nniwo@yahoo.com [Department of Chemical, Metallurgical and Materials Engineering, Tshwane University of Technology, Pretoria (South Africa); Department of Materials Science and Engineering, Obafemi Awolowo University (Nigeria); Atanda, P.O. [Department of Materials Science and Engineering, Obafemi Awolowo University (Nigeria); Aigbodion, V.S. [Department of Chemical, Metallurgical and Materials Engineering, Tshwane University of Technology, Pretoria (South Africa); Department of Metallurgical and Materials Engineering, University of Nigeria, Nsukka (Nigeria)

2016-05-05

The behaviour of γ′ phase to thermal and mechanical effects during rapid heating of Astroloy(Turbine Disc alloy) a Powder metallurgy (PM) nickel base superalloy has been investigated. The thermo-mechanical affected zone (TMAZ) and heat affected zone (HAZ) microstructure of an inertia friction welded Astroloy were simulated using a Gleeble thermo-mechanical simulation system. Detailed microstructural examination of the simulated TMAZ and HAZ and those present in actual inertial friction welded specimens showed that γ′ particles persisted during rapid heating up to a temperature where the formation of liquid is thermodynamically favoured, and subsequently re-solidified eutectically. The result obtained showed that forging during the thermo-mechanical simulation significantly enhanced resistance to weld liquation cracking of the alloy. This is attributable to strain-induced rapid isothermal dissolution of the constitutional liquation products within 150 μm from the centre of the forged sample. This was not observed in purely thermally simulated samples. The microstructure within the TMAZ of the as-welded alloy is similar to the microstructure in the forged Gleeble specimens. - Highlights: • The behaviour of γ′ phase to thermal and mechanical effects during rapid heating of Astrology • The thermo-mechanical affected zone (TMAZ) and heat affected zone (HAZ). • significantly enhanced resistance to weld liquation cracking of the alloy. • This was not observed in purely thermally simulated samples. • The microstructure within the TMAZ of the as-welded alloy is similar to the microstructure in the forged Gleeble specimens.

The Shape of Things to Come? Household Dependency Ratio and Adolescent Nutritional Status in Rural and Urban Ethiopia

Science.gov (United States)

Hadley, Craig; Belachew, Tefera; Lindstrom, David; Tessema, Fasil

2013-01-01

Several related demographic trends are occurring in developing countries: youth comprise a large portion of populations, fertility rates are declining, and urban dwellers are increasing. As fertility rates decline and populations age, the decline in the ratio of young dependents to working age adults is expected to free up household resources, which can be invested in human capital, including youth nutritional wellbeing. We test this hypothesis in a sample of youth (n = 1,934) in Southwestern Ethiopia. Multiple measures of achieved growth and nutritional status are explored (weight, height, mid-upper arm circumference (MUAC), body mass index (BMI) and body mass index for age z-score (BMIZ), weight for age z-score (WAZ), and height for age z-score (HAZ)). In multivariable models controlling for the effects of income, age, gender, and youth is workloads, youth living in rural settings had significantly lower weight (1.24 kg lighter), MUAC (0.67 cm lower), BMI (0.45 BMI lower), BMIZ (0.27 lower), HAZ (0.14 HAZ lower), and WAZ (0.3 WAZ lower) than urban youth (all P dependency ratio households, results show that youth in households with the highest dependency ratios were estimated to be 1.3 kg lighter, have 0.67 cm smaller MUAC, and BMI that was 0.59 lower (all Pdependency. These results may point toward increasing levels of human capital investments in Ethiopian youth as fertility levels decline and populations urbanize. Am J Phys Anthropol 144:643–652, 2011. PMID:21404240

Sadhana | Indian Academy of Sciences

Indian Academy of Sciences (India)

MRA) and artificial neural network (ANN) models to predict weld bead geometry and HAZ width in submerged arcwelding process. Design of experiments is based on Taguchi's L16 orthogonal array by varying wire feed rate,transverse speed ...

Effects of pulse current stimulation on the thermal fatigue crack propagation behavior of CHWD steel

International Nuclear Information System (INIS)

Lin, H.Q.; Zhao, Y.G.; Gao, Z.M.; Han, L.G.

2008-01-01

The fatigue crack propagating behaviors of cast hot working die (CHWD) steel untreated and treated by an electric current in the intermediate stage of thermal fatigue were investigated in the present study. The circle/elliptical heating affected zone (HAZ) was formed ahead of the notch tip on the fatigued specimens after pulse electric current stimulation. Both SEM observation and X-ray diffraction analysis revealed that pulse electric current stimulation refined grains/subgrains in the HAZs. With the prolonging of discharging duration, the grains/subgrains decreased in size and the dislocation density and microhardness increased gradually. The grain refinement and dislocation density increase played an important role in the material strengthening, which inevitably enhanced the propagation resistance and delayed the propagation of thermal fatigue cracks. Therefore, the pulse electric current stimulation was an effective method to improve the service lifetime of die material

Micro Structure and Hardness Analysis of Brass Metal Welded

Science.gov (United States)

Lukman Faris, N.; Muljadi; Djuhana

2018-01-01

Brass metals are widely used for plumbing fittings. High tensile brasses are more highly alloyed and find uses in marine engineering. The welding of brass metal has been done by using electrical weld machine (SMAW). The microstructure of brass metal welded was observed by optical microscope. The result can see that the microstructure has been changed due to heat from welding. The microstructure of original brass metal is seen a fine laminar stucture, but the microstructure at HAZ appears bigger grains and some area at HAZ is seen coarser microstructure. The microstructure at weld zone can be seen that it was found some of agglomeration of materials from reaction between brass metal and electrode coating wire. According the hardness measurement, it is found highest hardness value about 301.92 HV at weld zone, and hardness value at base metal is 177.84 HV

Kaybolmuş bir İçecek Kefir

OpenAIRE

Zekâi Varnacı

2015-01-01

Kafkasya’da bir parça dana veya koyun şirdeni keçi tulumlarında inek sütüyle maserasyona bırakılarak hazırlanır. Süt çabuk ve spontan olarak koagüle olur. Bundan sonra tulum yeniden doldurularak yeni bir işleme geçilir. Birkaç hafta sonra tulumun iç cidarlarında yavaş yavaş süngerimsi bir kabuk tabakası oluşur. İşte bu kabuk tabakası bölünüp veya kasılıp, sonra kurutularak kefir daneleri meydana getirilir. Danelerin görünüşü sarımsı, küçük, tomurcuğumsudur. Bu daneler kefirin hazırlanmasında ...

Kaybolmuş bir İçecek Kefir

OpenAIRE

Varnacı, Zekai

1980-01-01

Kafkasya’da bir parça dana veya koyun şirdeni keçi tulumlarında inek sütüyle maserasyona bırakılarak hazırlanır. Süt çabuk ve spontan olarak koagüle olur. Bundan sonra tulum yeniden doldurularak yeni bir işleme geçilir. Birkaç hafta sonra tulumun iç cidarlarında yavaş yavaş süngerimsi bir kabuk tabakası oluşur. İşte bu kabuk tabakası bölünüp veya kasılıp, sonra kurutularak kefir daneleri meydana getirilir. Danelerin görünüşü sarımsı, küçük, tomurcuğumsudur. Bu daneler kefirin hazırlanmasınd...

Fusion welding of borated stainless steels

International Nuclear Information System (INIS)

Robino, C.V.; Cieslak, M.J.

1993-01-01

Borated austenitic stainless steels have been developed for use in the nuclear industry where storage, transport, and reprocessing of nuclear materials are required. The objective of this work is to develop appropriate joining technology for borated stainless steels based upon understanding the response of these materials to thermal processing involving melting. This understanding is being developed through the application of physical metallurgy techniques to determine the evolution of microstructure and mechanical properties within the various regions of the HAZ. Initial investigations include development of the kinetics of boride coarsening in the solid-state region of HAZ and the effect of boride coarsening on the impact properties of this region of the weld zone. Microstructures of the borated stainless steels, their response to high temperature isothermal heat treatments, and the implications of these heat treatments with respect to welding behavior will be presented

Characterization of friction welding for IN713LC and AISI 4140 steel

International Nuclear Information System (INIS)

Yeom, J.T.; Park, N.K.; Park, J.H.; Lee, J.W.

2004-01-01

Friction welding of dissimilar materials, Ni-base superalloy IN713LC and oil-quench plus tempered AISI 4140 steel, was investigated. Friction welding was carried out with various process variables such as friction pressure and time. The quality of welded joints was tested by applying bending stresses in an appropriate jig. Microstructures of the heat-affected zone (HAZ) were investigated along with micro-hardness tests over the friction weld joints. DEFORM-2D FE code was used to simulate the effect of welding variables in friction welding process on the distributions of the state variables such as strain, strain rate and temperature. The formation of the metal burr during the friction welding process was successfully simulated, and the temperature distribution in the heat-affected zone indicated a good agreement with the variation of the microstructures in the HAZ. (orig.)

Characterization of friction welding for IN713LC and AISI 4140 steel

Energy Technology Data Exchange (ETDEWEB)

Yeom, J.T.; Park, N.K. [Dept. of Materials Processing, Korea Inst. of Machinery and Materials, Kyungnam (Korea); Park, J.H.; Lee, J.W. [ENPACO Co., Changwon (Korea)

2004-07-01

Friction welding of dissimilar materials, Ni-base superalloy IN713LC and oil-quench plus tempered AISI 4140 steel, was investigated. Friction welding was carried out with various process variables such as friction pressure and time. The quality of welded joints was tested by applying bending stresses in an appropriate jig. Microstructures of the heat-affected zone (HAZ) were investigated along with micro-hardness tests over the friction weld joints. DEFORM-2D FE code was used to simulate the effect of welding variables in friction welding process on the distributions of the state variables such as strain, strain rate and temperature. The formation of the metal burr during the friction welding process was successfully simulated, and the temperature distribution in the heat-affected zone indicated a good agreement with the variation of the microstructures in the HAZ. (orig.)

Evaluation of hydrogen-Induced cracking resistance of the In625 laser coating system on a C-Mn steel substrate

Directory of Open Access Journals (Sweden)

Vicente Braz Trindade

Full Text Available Abstract The corrosion of C-Mn steels in the presence of hydrogen sulfide (H2S represents a significant challenge to oil production and natural gas treatment facilities. The failure mechanism induced by hydrogen-induced cracking (HIC in a Inconel 625 coating / C-Mn steel has not been extensively investigated in the past. In the present work, an API 5CT steel was coated with In625 alloy using laser cladding and the HIC resistance of different regions, such as the coating surface, the substrate and HAZ, were evaluated. SEM observations illustrated that all HIC cracks were formed at the hard HAZ after 96h of exposure. No HIC cracks were observed in the substrate and the In625 coating after the same exposure duration. Pitting was recorded in the substrate caused by non-metallic inclusion dissolving.

Corrosion of 2205 Duplex Stainless Steel Weldment in Chloride Medium Containing Sulfate-Reducing Bacteria

Science.gov (United States)

Antony, P. J.; Singh Raman, R. K.; Kumar, Pradeep; Raman, R.

2008-11-01

Influence of changes in microstructure caused due to welding on microbiologically influenced corrosion of a duplex stainless steel was studied by exposing the weldment and parent metal to chloride medium containing sulfate-reducing bacteria (SRB). Identically prepared coupons (same area and surface finish) exposed to sterile medium were used as the control. Etching-type attack was observed in the presence of SRB, which was predominant in the heat-affected zone (HAZ) of the weldment. The anodic polarization studies indicated an increase in current density for coupon exposed to SRB-containing medium as compared to that obtained for coupon exposed to sterile medium. The scanning electron microscopy (SEM) observations after anodic polarization revealed that the attack was preferentially in the ferrite phase of HAZ of the weldment, whereas it was restricted to the austenite phase of the parent metal.

6229 Volume 12 No. 3 May 2012 NUTRITIONAL STATUS OF ...

African Journals Online (AJOL)

comp2

2012-05-03

May 3, 2012 ... showed the lowest prevalence (7% HAZ, 3% WAZ). The other ... has estimated that 32.5% of all pre-school children under 5 years of age are .... International development Agency (SIDA) for COBES field activities is highly.

Nutritional status in relation to the efficacy of the rhesus-human reassortant, tetravalent rotavirus vaccine (RRV-TV in infants from Belém, Pará State, Brazil Relação entre o estado nutricional e a eficácia da vacina tetravalente contra rotavírus de origem símio-humana, geneticamente rearranjada (RRV-TV, em crianças de Belém, Pará, Brasil

Directory of Open Access Journals (Sweden)

Alexandre C. LINHARES

2002-02-01

Full Text Available The rhesus-human reassortant, tetravalent rotavirus vaccine (RRV-TV was licensed for routine use in the United States of America but it was recently withdrawn from the market because of its possible association with intussusception as an adverse event. The protective efficacy of 3 doses of RRV-TV, in its lower-titer (4 x 10(4 pfu/dose formulation, was evaluated according to the nutritional status of infants who participated in a phase III trial in Belém, Northern Brazil. A moderate protection conferred by RRV-TV was related to weight-for-age Z-scores (WAZ greater than -1 only, with rates of 38% (p = 0.04 and 40% (p = 0.04 for all- and- pure rotavirus diarrhoeal cases, respectively. In addition, there was a trend for greater efficacy (43%, p = 0.05 among infants reaching an height-for-age Z-score (HAZ of > -1. Taking WAZ, HAZ and weight-for-height Z-score (WHZ indices 0.05 if both placebo and vaccine groups are compared. There was no significant difference if rates of mixed and pure rotavirus diarrhoeal cases are compared in relation to HAZ, WAZ and weight-for-height Z-score (WHZ indices. Although a low number of malnourished infants could be identified in the present study, our data show some evidence that malnutrition may interfere with the efficacy of rotavirus vaccines in developing countries.A vacina tetravalente contra rotavírus de origem símio-humana, geneticamente rearranjada (RRV-TV, foi licenciada para uso rotineiro nos Estados Unidos da América do Norte; entretanto, tal imunizante foi removido do mercado, uma vez que a intussuscepção emergiu como possível evento adverso vacinal. A eficácia da RRV-TV - em sua formulação menos concentrada (10 x 10(4 pfu/dose - foi avaliada no tocante ao estado nutricional das crianças que integraram estudo caracterizado como de fase III, levado a efeito em Belém, região norte do Brasil. Observou-se proteção (moderada apenas entre os indivíduos com escore "Z" (peso-por-idade, WAZ superior

Development of embrittlement prediction models for U.S. power reactors and the impact of the heat-affected zone to thermal annealing

International Nuclear Information System (INIS)

Wang, J.A.

1998-05-01

The NRC Regulatory Guide 1.99 Revision 2 was based on 177 surveillance data points and the EPRI data base, where 76% of 177 data points and 60% of EPRI data base were from Westinghouse's data. Therefore, other vendors' radiation environment may not be properly characterized by R.G. 1.99's prediction. To minimize scatter from the influences of the irradiation temperature, neutron energy spectrum, displacement rate, and plant operation procedures on embrittlement models, improved embrittlement models based on group data that have similar radiation environments and reactor design and operation criteria are examined. A total of 653 shift data points from the current FR-EDB, including 397 Westinghouse data, 93 B and W data, 37 CE data, and 106 GE data, are used. A nonlinear least squares fitting FORTRAN program, incorporating a Monte Carlo procedure with 35% and 10% uncertainty assigned to the fluence and shift data, respectively, was written for this study. In order to have the same adjusted fluence value for the weld and plate material in the same capsule, the Monte Carlo least squares fitting procedure has the ability to adjust the fluence values while running the weld and plate formula simultaneously. Six chemical components, namely, copper, nickel, phosphorus, sulfur, manganese, and molybdenum, were considered in the development of the new embrittlement models. The overall percentage of reduction of the 2-sigma margins per delta RTNDT predicted by the new embrittlement models, compared to that of R.G. 1.99, for weld and base materials are 42% and 36%, respectively. Currently, the need for thermal annealing is seriously being considered for several A302B type RPVs. From the macroscopic view point, even if base and weld materials were verified from mechanical tests to be fully recovered, the linking heat affected zone (HAZ) material has not been properly characterized. Thus the final overall recovery will still be unknown. The great data scatter of the HAZ metals may

Thermal Aging Effects on Residual Stress and Residual Strain Distribution on Heat Affected Zone of Alloy 600 in Dissimilar Metal Weld

Energy Technology Data Exchange (ETDEWEB)

Ham, Junhyuk; Choi, Kyoung Joon; Kim, Ji Hyun [UNIST, Ulsan (Korea, Republic of)

2016-10-15

Dissimilar metal weld (DMW), consisting of Alloy 600, Alloy 182, and A508 Gr.3, has been widely used as a joining material of the reactor pressure vessel penetration nozzle and the steam generator tubing for pressurized water reactors (PWR) because of its good mechanical strength, thermal conductivity, and corrosion resistance. Residual tensile stress is mainly nominated as a cause of SCC in light water reactors by IAEA report. So, to relax the residual stress, post-weld heat treatment is required after manufacturing process such as welding. However, thermal treatment has a great effect on the microstructure and the chromium depletion profile on Alloy 600, so called sensitization. By this reason, HAZ on Alloy 600 is critical to crack. According to G.A. Young et al., Crack growth rates (CGR) in the Alloy 600 HAZ were about 30 times faster than those in the Alloy 600 base metal tested under the same conditions. And according to Z.P. Lu et al., CGR in the Alloy 600 HAZ can be more than 20 times higher than that in its base metal. There are some methods to measure the exact value of residual stress on the material surface. The most common way is X-ray diffraction method (XRD). The principle of XRD is based on lattice strains and depends on the changes in the spacing of the atomic planes in material. And there is a computer simulation method to estimate residual stress distribution which is called ANSYS. This study was conducted to investigate how thermal aging affects residual stress and residual strain distribution of Alloy 600 HAZ. Following conclusions can be drawn from this study. According to preceding researches and this study, both the relaxation of residual stress and the change of residual strain follow as similar way, spreading out from concentrated region. The result of Vickers micro-hardness tester shows that tensile residual stresses are distributed broadly on the material aged by 15 years. Therefore, HT400{sub Y}15 material is weakest state for PWSCC. The

Hazard Evaluation for Storage of Spent Nuclear Fuel (SNF) Sludge at the Solid Waste Treatment Facility

International Nuclear Information System (INIS)

SCHULTZ, M.V.

2000-01-01

As part of the Spent Nuclear Fuel (SNF) storage basin clean-up project, sludge that has accumulated in the K Basins due to corrosion of damaged irradiated N Reactor will be loaded into containers and placed in interim storage. The Hanford Site Treatment Complex (T Plant) has been identified as the location where the sludge will be stored until final disposition of the material occurs. Long term storage of sludge from the K Basin fuel storage facilities requires identification and analysis of potential accidents involving sludge storage in T Plant. This report is prepared as the initial step in the safety assurance process described in DOE Order 5480.23, Nuclear Safety Analysis Reports and HNF-PRO-704, Hazards and Accident Analysis Process. This report documents the evaluation of potential hazards and off-normal events associated with sludge storage activities. This information will be used in subsequent safety analyses, design, and operations procedure development to ensure safe storage. The hazards evaluation for the storage of SNF sludge in T-Plant used the Hazards and Operability Analysis (HazOp) method. The hazard evaluation identified 42 potential hazardous conditions. No hazardous conditions involving hazardous/toxic chemical concerns were identified. Of the 42 items identified in the HazOp study, eight were determined to have potential for onsite worker consequences. No items with potential offsite consequences were identified in the HazOp study. Hazardous conditions with potential onsite worker or offsite consequences are candidates for quantitative consequence analysis. The hazardous conditions with potential onsite worker consequences were grouped into two event categories, Container failure due to overpressure - internal to T Plant, and Spill of multiple containers. The two event categories will be developed into accident scenarios that will be quantitatively analyzed to determine release consequences. A third category, Container failure due to

Sato Processes in Default Modeling

DEFF Research Database (Denmark)

Kokholm, Thomas; Nicolato, Elisa

2010-01-01

In reduced form default models, the instantaneous default intensity is the classical modeling object. Survival probabilities are then given by the Laplace transform of the cumulative hazard defined as the integrated intensity process. Instead, recent literature tends to specify the cumulative haz...

The relationship between stunting and overweight among children ...

African Journals Online (AJOL)

in the first 2 years of life and who thereafter rapidly gained weight during childhood or ..... BMI and HAZ (p<0.0001), which supports the literature from. SA indicating that ... gov/obesity/childhood/basics.html (accessed 12 June 2015). 4. Lloyd LJ ...

Effect of Heat Input on Microstructure and Hardness Distribution of Laser Welded Si-Al TRIP-Type Steel

Directory of Open Access Journals (Sweden)

Adam Grajcar

2014-01-01

Full Text Available This study is concerned with issues related to laser welding of Si-Al type TRIP steels with Nb and Ti microadditions. The tests of laser welding of thermomechanically rolled sheet sections were carried out using keyhole welding and a solid-state laser. The tests carried out for various values of heat input were followed by macro- and microscopic metallographic investigations as well as by microhardness measurements of welded areas. A detailed microstructural analysis was carried out in the penetration area and in various areas of the heat affected zone (HAZ. Special attention was paid to the influence of cooling conditions on the stabilisation of retained austenite, the most characteristic structural component of TRIP steels. The tests made it possible to determine the maximum value of heat input preventing the excessive grain growth in HAZ and to identify the areas of the greatest hardness reaching 520 HV0.1.

Liquation Cracking in the Heat-Affected Zone of IN738 Superalloy Weld

Directory of Open Access Journals (Sweden)

Kai-Cheng Chen

2018-05-01

Full Text Available The main scope of this study investigated the occurrence of liquation cracking in the heat-affected zone (HAZ of IN738 superalloy weld, IN738 is widely used in gas turbine blades in land-based power plants. Microstructural examinations showed considerable amounts of γ’ uniformly precipitated in the γ matrix. Electron probe microanalysis (EPMA maps showed the γ-γ’ colonies were rich in Al and Ti, but lean in other alloy elements. Moreover, the metal carbides (MC, fine borides (M3B2 and M5B3, η-Ni3Ti, σ (Cr-Co and lamellar Ni7Zr2 intermetallic compounds could be found at the interdendritic boundaries. The fracture morphologies and the corresponding EPMA maps confirmed that the liquation cracking in the HAZ of the IN738 superalloy weld resulted from the presence of complex microconstituents at the interdendritic boundaries.

Effects of aging treatment and heat input on the microstructures and mechanical properties of TIG-welded 6061-T6 alloy joints

Science.gov (United States)

Peng, Dong; Shen, Jun; Tang, Qin; Wu, Cui-ping; Zhou, Yan-bing

2013-03-01

Aging treatment and various heat input conditions were adopted to investigate the microstructural evolution and mechanical properties of TIG welded 6061-T6 alloy joints by microstructural observations, microhardness tests, and tensile tests. With an increase in heat input, the width of the heat-affected zone (HAZ) increases and grains in the fusion zone (FZ) coarsen. Moreover, the hardness of the HAZ decreases, whereas that of the FZ decreases initially and then increases with an increase in heat input. Low heat input results in the low ultimate tensile strength of the welded joints due to the presence of partial penetrations and pores in the welded joints. After a simple artificial aging treatment at 175°C for 8 h, the microstructure of the welded joints changes slightly. The mechanical properties of the welded joints enhance significantly after the aging process as few precipitates distribute in the welded seam.

The influence of low dose irradiation on the creep properties of type 316 welds

International Nuclear Information System (INIS)

Marshall, P.; Steeds, J.W.; Lin, Y.P.; Finlan, G.T.

1987-01-01

Fully instrumented creep and stress rupture tests have been performed at 873K for times up to 20,000h on a series of type 316 steel/17Cr 8Ni 2Mo weld metal specimens in the unirradiated and thermal neutron irradiated conditions. The specimens tested included all weld metal longitudinal and transverse composites in the as-welded condition and following a stress relief heat treatment of 10h at 1075K. Simulated heat affected zone (HAZ) specimens were also tested. Analysis of the creep results combined with metallography, autoradiography and TEM established that the decrease in properties of irradiated samples is caused by an increasing secondary strain rate due to enhanced helium induced grain boundary fracture of the simulated HAZ and enhanced interdendritic fracture in the weld metal. Implications of strength reductions on the design of welded structures subjected to thermal irradiation are briefly assessed. (author)

3D modelling of plug failure in resistance spot welded shear-lab specimens (DP600-steel)

DEFF Research Database (Denmark)

Nielsen, Kim Lau

2008-01-01

are based on uni-axial tensile testing of the basis material, while the modelled tensile response of the shear-lab specimens is compared to experimental results for the case of a ductile failure near the heat affected zone (HAZ). A parametric study for a range of weld diameters is carried out, which makes......Ductile plug failure of resistance spot welded shear-lab specimens is studied by full 3D finite element analysis, using an elastic-viscoplastic constitutive relation that accounts for nucleation and growth of microvoids to coalescence (The Gurson model). Tensile properties and damage parameters...... it possible to numerically relate the weld diameter to the tensile shear force (TSF) and the associated displacement, u (TSF) , respectively. Main focus in the paper is on modelling the localization of plastic flow and the corresponding damage development in the vicinity of the spot weld, near the HAZ...

Kaybolmuş bir İçecek Kefir

Directory of Open Access Journals (Sweden)

Zekâi Varnacı

2015-02-01

Full Text Available Kafkasya’da bir parça dana veya koyun şirdeni keçi tulumlarında inek sütüyle maserasyona bırakılarak hazırlanır. Süt çabuk ve spontan olarak koagüle olur. Bundan sonra tulum yeniden doldurularak yeni bir işleme geçilir. Birkaç hafta sonra tulumun iç cidarlarında yavaş yavaş süngerimsi bir kabuk tabakası oluşur. İşte bu kabuk tabakası bölünüp veya kasılıp, sonra kurutularak kefir daneleri meydana getirilir. Danelerin görünüşü sarımsı, küçük, tomurcuğumsudur. Bu daneler kefirin hazırlanmasında maya olarak kullanılmak üzere ticarete arzedilir.

Matematik dersi 1.-5. sınıf öğretim programının NCTM prensip ve standartlarına göre incelenmesi

OpenAIRE

UMAY, AYSUN; ÇIKLA, OYLUM AKKUŞ; DUATEPE, ASUMAN

2006-01-01

Milli Eğitim Bakanlığı tarafından 2004-2005 öğretim yılında uygulanmak üzere hazırlanan yeni öğretim programları, eğitimdünyasındaki çağdaş gelişimleri yakalamak için önemli bir adım sayılabilir. Bu çalışmada İlköğretim 1.-5. sınıf Matematik DersiÖğretim Programı (İMDÖP), NCTM tarafından 2000 yılında hazırlanan, okul matematiği için dikkate alınması gereken prensip vestandartları açıklayan Principles and Standards for School Mathematics (PSSM) adlı dokümanı ölçüt alınarak incelenmiştir. Budok...

昆明地区危险废物处理处置及防治对策分析%Analysis of Precaution and Treatment and Disposal of Hazardous Wastes in Kunming

Institute of Scientific and Technical Information of China (English)

陈松

2014-01-01

The Management of hazardous wastes at home and aboard was introduced.A deep analysis of how haz-ardous wastes were managed in Kunming was done.The analysis covered the treatment and disposal status of haz-ardous wastes,the categories of wastes,the amount of wastes,and problems of waste management.Countermeas-ures were urged to promote the hazardous waste management in Kunming.%介绍了国内外危险废物管理情况。就昆明地区危险废物的管理，处理处置现状，危险废物种类、产生量，以及管理存在的问题和不足进行了深入分析。在此基础上提出了相应的防治对策。

Welding processes for Inconel 718- A brief review

Science.gov (United States)

Tharappel, Jose Tom; Babu, Jalumedi

2018-03-01

Inconel 718 is being extensively used for high-temperature applications, rocket engines, gas turbines, etc. due to its ability to maintain high strength at temperatures range 450-700°C complimented by excellent oxidation and corrosion resistance and its outstanding weldability in either the age hardened or annealed condition. Though alloy 718 is reputed to possess good weldability in the context of their resistance to post weld heat treatment cracking, heat affected zone (HAZ) and weld metal cracking problems persist. This paper presents a brief review on welding processes for Inconel 718 and the weld defects, such as strain cracking during post weld heat treatment, solidification cracking, and liquation cracking. The effect of alloy chemistry, primary and secondary processing on the HAZ cracking susceptibility, influence of post/pre weld heat treatments on precipitation, segregation reactions, and effect of grain size etc. discussed and concluded with future scope for research.

On the shakedown analysis of welded pipes

International Nuclear Information System (INIS)

Li Tianbai; Chen Haofeng; Chen Weihang; Ure, James

2011-01-01

This paper presents the shakedown analysis of welded pipes subjected to a constant internal pressure and a varying thermal load. The Linear Matching Method (LMM) is applied to investigate the upper and lower bound shakedown limits of the pipes. Individual effects of i) geometry of weld metal, ii) ratio of inner radius to wall thickness and iii) all material properties of Weld Metal (WM), Heat Affected Zone (HAZ) and Parent Material (PM) on shakedown limits are investigated. The ranges of these variables are chosen to cover the majority of common pipe configurations. Corresponding individual influence functions on the shakedown limits are generated. These are then combined to allow the creation of a safety shakedown envelope, which can be used for the design of any welded pipes within the specified ranges. The effect of temperature-dependent yield stress (in PM, HAZ and WM) on these shakedown limits is also investigated.

Three-dimensional numerical simulation during laser processing of CFRP

Science.gov (United States)

Ohkubo, Tomomasa; Sato, Yuji; Matsunaga, Ei-ichi; Tsukamoto, Masahiro

2017-09-01

We performed three-dimensional numerical simulation about laser processing of carbon-fiber-reinforced plastic (CFRP) using OpenFOAM as libraries of finite volume method (FVM). Although a little theoretical or numerical studies about heat affected zone (HAZ) formation were performed, there is no research discussing how HAZ is generated considering time development about removal of each material. It is important to understand difference of removal speed of carbon fiber and resin in order to improve quality of cut surface of CFRP. We demonstrated how the carbon fiber and resin are removed by heat of ablation plume by our simulation. We found that carbon fiber is removed faster than resin at first stage because of the difference of thermal conductivity, and after that, the resin is removed faster because of its low combustion temperature. This result suggests the existence of optimal contacting time of the laser ablation and kerf of the target.

Statistical aspects of fatigue crack growth life of base metal, weld metal and heat affected zone in FSWed 7075-T651aluminum alloy

International Nuclear Information System (INIS)

Sohn, Hye Jeong; Haryadi, Gunawan Dwi; Kim, Seon Jin

2014-01-01

The statistical aspects of fatigue crack growth life of base metal (BM), weld metal (WM) and heat affected zone (HAZ) in friction stir welded (FSWed) 7075-T651 aluminum alloy has been studied by Weibull statistical analysis. The fatigue crack growth tests were performed at room temperature on ASTM standard CT specimens under three different constant stress intensity factor range controls. The main objective of this paper is to investigate the effects of statistical aspects of fatigue crack growth life on stress intensity factor ranges and material properties, namely BM, WM and HAZ specimens. In this work, the Weibull distribution was employed to estimate the statistical aspects of fatigue crack growth life. The shape parameter of Weibull distribution for fatigue crack growth life was significantly affected by material properties and the stress intensity factor range. The scale parameter of WM specimen exhibited the lowest value at all stress intensity factor ranges.

Study of microstructure and mechanical property relationships of A-TIG welded P91–316L dissimilar steel joint

Energy Technology Data Exchange (ETDEWEB)

Vidyarthy, R.S., E-mail: vidyashanker01@gmail.com; Kulkarni, A.; Dwivedi, D.K.

2017-05-17

The current work enunciated the effect of activating flux tungsten inert gas (A-TIG) welding on the microstructural, mechanical and corrosion behaviour of the 316L stainless steel (SS) and P91 steel weldment. The current study also demonstrated the comprehensive structure–property relationships of dissimilar joint weldment using the collective techniques of optical macro and microscopy, electron microscopy, and Energy-dispersive X-ray spectroscopy (EDS) techniques. Microstructure study reveals the presence of delta ferrite, austenite and martensite in different zones of the weldment. The dissimilar steel weldment failed from the 316L side fusion boundary during the tensile testing. Maximum impact energy was absorbed by the 316L SS side heat affected zone (HAZ) while minimum by P91 steel side HAZ during the Charpy toughness test. The potentiodynamic test result suggested that the P91 side fusion boundary had minimum corrosion and pitting potential in all the weldment.

Metallurgical transformations of high strength low alloys steels 450 EMZ type II in the heat affected zone during multipass submerged arc welding

International Nuclear Information System (INIS)

Gonzalez-Palma, R.; Suarez-Bermejo, J. C.; Vicario, F. J.; Munoz, A.

2006-01-01

A considerable number of crack tip opening displacement tests in the heat affected zone (HAZ) of multipass welds. performed in accordance with standards BS 5762 and EEMUA, are rejected since the crack is not inside the coarse grain region at 0.5 mm from the fusion border, as well as the quantity of the crack length in percentage, that the crack goes through the inter critical region instead of in the grain coarse region as it would correspond. This circumstance make advisable to carry out a metallographic study of he inter critical zone in the HAZ as well as the corresponding tests, in order analyze the inter critical region brittleness reasons. The study is performed on a HSLA 75 mm thick panel 450 EMZ type II, welded under a SAW process with heat input and welded parameters controlled, without any post weld heat treatment. (Author)

Influence of repair length on residual stress in the repair weld of a clad plate

International Nuclear Information System (INIS)

Jiang Wenchun; Xu, X.P.; Gong, J.M.; Tu, S.T.

2012-01-01

Highlights: ► Residual stress in the repair weld of a stainless steel clad plate is investigated. ► The effect of repair length on residual stress has been studied. ► Large tensile residual stress is generated in the repair weld and heat affected zone. ► With the increase of repair length, transverse stress is decreased. ► Repair length has little effect on longitudinal stress. - Abstract: A 3-D sequential coupling finite element simulation is performed to investigate the temperature field and residual stress in the repair weld of a stainless steel clad plate. The effect of repair length on residual stress has been studied, aiming to provide a reference for repairing the cracked clad plate. The results show that large tensile residual stresses are generated in the repair weld and heat affected zone (HAZ), and then decrease gradually away from the weld and HAZ. The residual stresses through thickness in the clad layer are relative uniform, while they are non-uniform in the base metal. A discontinuous stress distribution is generated across the interface between weld metal and base metal. The repair length has a great effect on transverse stress. With the increase of repair length, the transverse stress is decreased. When the repair length is increased to 14 cm, the peak of transverse stress has been decreased below yield strength, and the transverse stress in the weld and HAZ has also been greatly decreased. But the repair length has little effect on longitudinal stress.

Characterization of microstructure of A508III/309L/308L weld and oxide films formed in deaerated high-temperature water

Science.gov (United States)

Xiong, Qi; Li, Hongjuan; Lu, Zhanpeng; Chen, Junjie; Xiao, Qian; Ma, Jiarong; Ru, Xiangkun

2018-01-01

The microstructure of A508III/309L/308L weld clad and the properties of the oxide films formed in simulated pressurized water reactor primary water at 290 °C were characterized. The A508III heat-affected zone (HAZ) consisted primarily of a decarburization zone with ferrite near the fusion line and a following pearlite structure with fine grains. A high hardness region in the HAZ could be the result of C-enrichment. M23C6 and M7C3 precipitates were observed in element transition zone. 308L stainless steel (SS) containing ∼ 12% ferrites exhibited both ferritic-austenitic solidification mode (FA mode, δ→γ) and austenitic-ferritic solidification mode (AF mode, γ→δ), whereas 309L SS containing ∼ 9% ferrites exhibited only FA mode. The A508III surface oxide film was mainly Fe3O4 in deaerated high-temperature water. The coarse grain zone covered with few oxide particles was different from other types of film on the other region of HAZ and the bulk zone. More pitting appears on 309L SS after immersion in deaerated high-temperature water due to the dissolution of inclusions. SS surface oxide films consisted primarily of spinels. The oxide film on SS was divided into two layers. Ni was concentrated mainly at the oxide/substrate interface. The oxide film formed on 309L was thicker than that on the 308L. The ferrite in the stainless steel could improve the oxidation resistance.

Integrity assessment of the ferritic / austenitic dissimilar weld joint between intermediate heat exchanger and steam generator in fast reactor

Energy Technology Data Exchange (ETDEWEB)

Jayakumar, T.; Laha, K.; Chandravathi, K. S.; Parameswaran, P.; Goyal, S.; Kumar, J. G.; Mathew, M. D. [Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research, Kalpakkam- 603 102 (India)

2012-07-01

Integrity of the modified 9Cr-1Mo / alloy 800 dissimilar joint welded with Inconel 182 electrodes has been assessed under creep condition based on the detailed analysis of microstructure and stress distribution across the joint by finite element analysis. A hardness peak at the ferritic / austenitic weld interface and a hardness trough at the inter-critical heat affected zone (HAZ) in ferritic base metal developed. Un-tempered martensite was found at the ferritic / austenitic weld interface to impart high hardness in it; whereas annealing of martensitic structure of modified 9Cr-1Mo steel by inter-critical heating during welding thermal cycle resulted in hardness tough in the inter-critical HAZ. Creep tests were carried out on the joint and ferritic steel base metal at 823 K over a stress range of 160-320 MPa. The joint possessed lower creep rupture strength than its ferritic steel base metal. Failure of the joint at relatively lower stresses occurred at the ferritic / austenitic weld interface; whereas it occurred at inter-critical region of HAZ at moderate stresses. Cavity nucleation associated with the weld interface particles led to premature failure of the joint. Finite element analysis of stress distribution across the weld joint considering the micro-mechanical strength inhomogeneity across it revealed higher von-Mises and principal stresses at the weld interface. These stresses induced preferential creep cavitation at the weld interface. Role of precipitate in enhancing creep cavitation at the weld interface has been elucidated based on the FE analysis of stress distribution across it. (authors)

Variation behavior of residual stress distribution by manufacturing processes in welded pipes of austenitic stainless steel

International Nuclear Information System (INIS)

Ihara, Ryohei; Hashimoto, Tadafumi; Mochizuki, Masahito

2012-01-01

Stress corrosion cracking (SCC) has been observed near heat affected zone (HAZ) of primary loop recirculation pipes made of low-carbon austenitic stainless steel type 316L in the nuclear power plants. For the non-sensitization material, residual stress is the important factor of SCC, and it is generated by machining and welding. In the actual plants, welding is conducted after machining as manufacturing processes of welded pipes. It could be considered that residual stress generated by machining is varied by welding as a posterior process. This paper presents residual stress variation due to manufacturing processes of pipes using X-ray diffraction method. Residual stress distribution due to welding after machining had a local maximum stress in HAZ. Moreover, this value was higher than residual stress generated by welding or machining. Vickers hardness also had a local maximum hardness in HAZ. In order to clarify hardness variation, crystal orientation analysis with EBSD method was performed. Recovery and recrystallization were occurred by welding heat near the weld metal. These lead hardness decrease. The local maximum region showed no microstructure evolution. In this region, machined layer was remained. Therefore, the local maximum hardness was generated at machined layer. The local maximum stress was caused by the superposition effect of residual stress distributions due to machining and welding. Moreover, these local maximum residual stress and hardness are exceeded critical value of SCC initiation. In order to clarify the effect of residual stress on SCC initiation, evaluation including manufacturing processes is important. (author)

A review of hot cracking in austenitic stainless steel weldments

International Nuclear Information System (INIS)

Shankar, V.; Gill, T.P.S.; Mannan, S.L.; Rodriguez, P.

1991-01-01

The occurrence of hot cracking in austenitic stainless steel weldments is discussed with respect to its origin and metallurgical contributory factors. Of the three types of hot cracking, namely solidification cracking, liquation and ductility dip cracking, solidification cracking occurs in the interdendritic regions in weld metal while liquation and ductility dip cracking occur intergranularly in the heat-affected zone (HAZ). Segregation of impurity and minor elements such as sulphur, phosphorous, silicon, niobium, boron etc to form low melting eutectic phases has been found to be the major cause of hot cracking. Control of HAZ cracking requires minimisation of impurity elements in the base metal. In stabilized stainless steels containing niobium, higher amounts of delta-ferrite have been found necessary to prevent cracking than in unstabilized compositions. Titanium compounds have been found to cause liquation cracking in maraging steels and titanium containing stainless steels and superalloys. In nitrogen added stainless steels, cracking resistance decreases when the solidification mode changes to primary austenitic due to nitrogen addition. A review of the test methods to evaluate hot cracking behaviour showed that several external restraint and semi-self-restraint tests are available. The finger Test, WRC Fissure Bend Test, the PVR test and the Varestraint Test are described along with typical test results. Hot ductility testing to reveal HAZ cracking tendency during welding is described, which is of particular importance to stabilized stainless steels. Based on the literature, recommendations are made for welding stabilized and nitrogen added steels, indicating areas of further work. (author). 81 refs., 30 figs., 1 tab

Creep rupture behavior of 9Cr–1.8W–0.5Mo–VNb (ASME grade 92) ferritic steel weld joint

Energy Technology Data Exchange (ETDEWEB)

Sakthivel, T., E-mail: tsakthivel@igcar.gov.in; Vasudevan, M.; Laha, K., E-mail: laha@igcar.gov.in; Parameswaran, P.; Chandravathi, K.S.; Panneer Selvi, S.; Maduraimuthu, V.; Mathew, M.D.

2014-01-03

Creep rupture behavior of 9Cr–1.8W–0.5Mo–VNb (ASME grade 92) ferritic steel weld joint fabricated by activated TIG (A-TIG) welding process have been investigated at 923 K over a stress range of 80–150 MPa. The weld joint was comprise of fusion zone, heat affected zone (HAZ) and base metal. The HAZ consisted of coarse prior-austenite grain (CGHAZ), fine prior-austenite grain (FGHAZ) and intercritical (ICHAZ) regions in an order away from the fusion zone to base metal. A hardness trough was observed at the outer edge of HAZ of the weld joint. TEM investigation revealed the presence of coarse M{sub 23}C{sub 6} precipitates and recovery of martensite lath structure into subgrain in the ICHAZ of the weld joint, leading to the hardness trough. The weld joint exhibited lower creep rupture lives than the base metal at relatively lower stresses. Creep rupture failure location of the weld joint was found to shift with applied stress. At high stresses fracture occurred in the base metal, whereas failure location shifted to FGHAZ at lower stresses with significant decrease in rupture ductility. SEM investigation of the creep ruptured specimens revealed precipitation of Laves phase across the joint, more extensively in the FGHAZ. On creep exposure, the hardness trough was found to shift from the ICHAZ to FGHAZ. Extensive creep cavitation was observed in the FGHAZ and was accompanied with the Laves phase, leading to the premature type IV failure of the steel weld joint at the FGHAZ.

Impact Toughness of Subzones in the Intercritical Heat-Affected Zone of Low-Carbon Bainitic Steel.

Science.gov (United States)

Li, Zhenshun; Zhao, Xuemin; Shan, Dongri

2018-06-06

The subzones of the intercritical heat-affected zone (IC HAZ) of low-carbon bainitic steel were simulated by using a Gleeble-3500 simulator to study the impact toughness. The results showed that the IC HAZ is not entirely brittle and can be further divided into three subzones according to the impact toughness or peak welding temperature; the invariant subzone heated between the critical transformation start temperature ( A c1 ) and 770 °C exhibited unchanged high impact toughness. Furthermore, an extremely low impact toughness was found in the embrittlement subzone, heated between 770 and 830 °C, and the reduction subzone heated between 830 °C and the critical transformation finish temperature ( A c3 ) exhibited toughness below that of the original metal. The size of the blocky martensite-austenite (M-A) constituents was found to have a remarkable level of influence on the impact toughness when heated below 830 °C. Additionally, it was found that, once the constituent size exceeds a critical value of 3.0 µm at a peak temperature of 770 °C, the IC HAZ becomes brittle regardless of lath or twinned martensite constitution in the M-A constituent. Essentially, embrittlement was observed to occur when the resolved length of initial cracks (in the direction of the overall fracture) formed as a result of the debonding of M-A constituents exceeding the critical Griffith size. Furthermore, when the heating temperature exceeded 830 °C, the M-A constituents formed a slender shape, and the impact toughness increased as the area fraction of the slender M-A constituents decreased.

What difference can fathers make? Early paternal absence compromises Peruvian children's growth.

Science.gov (United States)

Dearden, Kirk; Crookston, Benjamin; Madanat, Hala; West, Joshua; Penny, Mary; Cueto, Santiago

2013-01-01

Considerable evidence suggests that fathers' absence from home has a negative short- and long-term impact on children's health, psychosocial development, cognition and educational experience. We assessed the impact of father presence during infancy and childhood on children's height-for-age z-score (HAZ) at 5 years old. We conducted secondary data analysis from a 15-year cohort study (Young Lives) focusing on one of four Young Lives countries (Peru, n = 1821). When compared with children who saw their fathers on a daily or weekly basis during infancy and childhood, children who did not see their fathers regularly at either period had significantly lower HAZ scores (-0.23, P = 0.0094) after adjusting for maternal age, wealth and other contextual factors. Results also suggest that children who saw their fathers during childhood (but not infancy) had better HAZ scores than children who saw their fathers in infancy and childhood (0.23 z-score, P = 0.0388). Findings from analyses of resilient children (those who did not see their fathers at either round but whose HAZ > -2) show that a child's chances of not being stunted in spite of paternal absence at 1 and 5 years old were considerably greater if he or she lived in an urban area [odds ratio (OR) = 9.3], was from the wealthiest quintile (OR = 8.7) and lived in a food secure environment (OR = 3.8). Interventions designed to reduce malnutrition must be based on a fuller understanding of how paternal absence puts children at risk of growth failure. © 2011 Blackwell Publishing Ltd.

A Metallurgical Investigation of the Direct Energy Deposition Surface Repair of Ferrous Alloys

Science.gov (United States)

Marya, Manuel; Singh, Virendra; Hascoet, Jean-Yves; Marya, Surendar

2018-02-01

Among additive manufacturing (AM) processes, the direct energy deposition (DED) by laser is explored to establish its applicability for the repair of ferrous alloys such as UNS G41400 low-alloy steel, UNS S41000 martensitic stainless steel, UNS S17400 precipitation-strengthened martensitic stainless steel, and UNS S32750 super-duplex stainless steel. Unlike plating, thermal spray, and conventional cladding weld, DED laser powder deposition offers potential advantages, e.g., thin deposits, limited dilutions, narrow heat-affected zones (HAZ), potentially improved surface properties. In this investigation, all AM deposits were completed with an IREPA CLAD™ system using a powder feed of UNS N06625, an alloy largely selected for its outstanding corrosion resistance. This investigation first addresses topological aspects of AM deposits (including visual imperfections) before focusing on changes in microstructure, microhardness, chemical composition across AM deposits and base materials. It has been established that dense, uniform, hard ( 300 HVN), crack-free UNS N06625-compliant AM deposits of fine dendritic microstructures are reliably produced. However, except for the UNS S32750 steel, a significant martensitic hardening was observed in the HAZs of UNS G41400 ( 650 HVN), UNS S41000 ( 500 HVN), and UNS S17400 ( 370 HVN). In summary, this investigation demonstrates that the DED laser repair of ferrous parts with UNS N06625 may restore damaged surfaces, but it also calls for cautions and complementary investigations for alloys experiencing a high HAZ hardening, for which industry standard recommendations are exceeded and lead to an increased risk of delayed cracking in corrosive environments.

Effect of electromagnetic interaction during fusion welding of AISI 2205 duplex stainless steel on the corrosion resistance

Energy Technology Data Exchange (ETDEWEB)

García-Rentería, M.A., E-mail: marcogarciarenteria@uadec.edu.mx [Faculty of Metallurgy, Autonomous University of Coahuila, Carretera 57 Km. 5, CP 25720, Monclova, Coahuila (Mexico); López-Morelos, V.H., E-mail: vhlopez@umich.mx [Instituto de Investigación en Metalurgia y Materiales, Universidad Michoacana de San Nicolás de Hidalgo, A.P. 888, CP 58000, Morelia, Michoacán (Mexico); González-Sánchez, J., E-mail: jagonzal@uacam.mx [Centre for Corrosion Research, Autonomous University of Campeche, Av. Agustín Melgar s/n, Col. Buenavista, CP 24039, Campeche, Cam (Mexico); García-Hernández, R., E-mail: rgarcia@umich.mx [Instituto de Investigación en Metalurgia y Materiales, Universidad Michoacana de San Nicolás de Hidalgo, A.P. 888, CP 58000, Morelia, Michoacán (Mexico); Dzib-Pérez, L., E-mail: franciscocl7@yahoo.com.mx [Centre for Corrosion Research, Autonomous University of Campeche, Av. Agustín Melgar s/n, Col. Buenavista, CP 24039, Campeche, Cam (Mexico); Curiel-López, F.F., E-mail: franciscocl7@yahoo.com.mx [Faculty of Metallurgy, Autonomous University of Coahuila, Carretera 57 Km. 5, CP 25720, Monclova, Coahuila (Mexico)

2017-02-28

Highlights: • Application of EMILI during welding 2205 Duplex stainless steel hindered the coarsening of δ grains in HTHAZ and promoted regeneration of γ. • Welds made with simultaneous EMILI presented TPI values at the HTHAZ similar to those for BM. • Welds made under 3, 12 and 15 mT presented a mass loss by anodic polarisation similar to that observed for the as-received BM. • This behaviour is due to changes in the dynamics of microstructural evolution during welding with EMILI. - Abstract: The effect of electromagnetic interaction of low intensity (EMILI) applied during fusion welding of AISI 2205 duplex stainless steel on the resistance to localised corrosion in natural seawater was investigated. The heat affected zone (HAZ) of samples welded under EMILI showed a higher temperature for pitting initiation and lower dissolution under anodic polarisation in chloride containing solutions than samples welded without EMILI. The EMILI assisted welding process developed in the present work enhanced the resistance to localised corrosion due to a modification on the microstructural evolution in the HAZ and the fusion zone during the thermal cycle involved in fusion welding. The application of EMILI reduced the size of the HAZ, limited coarsening of the ferrite grains and promoted regeneration of austenite in this zone, inducing a homogeneous passive condition of the surface. EMILI can be applied during fusion welding of structural or functional components of diverse size manufactured with duplex stainless steel designed to withstand aggressive environments such as natural seawater or marine atmospheres.

Laser desensitization of austenitic stainless steel weld AHZ. Desensibilizacion con Laser de la zona afectada por el calor (ZAC) en aceros inoxidables austeniticos

Energy Technology Data Exchange (ETDEWEB)

Lee, C.H.; Kim, K.C.; Chang, R.W. (Welding Research Center Research Institute of Industrial Science and Technology, Pohang (Korea, Republic of))

1994-01-01

This paper addressed the fundamental understanding of sensitization phenomena in the weld HAZ of austenitic stainless steel and a method of desensitization utilizing LASER, without degradation of other corrosion resistance (pitting resistance). Sensitization in the weld HAZ was due to a formation of CR depleted zone along grain boundaries and twin boundaries by precipitation of Cr[sub 2]3C[sub 6] which contains 70-80% Cr and a small amount of Fe having a cubic-cubic relationship with the austenite matrix. Common morphologies of carbides were found to be of bar and globular shapes. As the holding time increased, carbides with coarsened globular (iodomorph) and dendrite shapes were also found. However, there was no significant variation in the composition of carbides and width of the Cr depleted zone with morphology. Laser desensitization could be obtained with a proper choice of the beam power and travel speed under a constant beam size. As long as the beam density reached a critical amount, carbides and Cr depleted zone completed zone completely disappeared. The critical travel speed increased with higher beam power, but was constant regardless of the original degree of sensitization. Pitting resistance of the LASER desensitized base metal and HAZ appeared to be far superior to that found in the sensitized condition. The protection potential in the hysteresis loop test was very sensitive to the degree of sensitization, revealing that the protection potential was dependent upon the propagation of the pits through the Cr depleted grain boundaries. (Author) 10 refs.

Welding repair during maintenance operations on EDF's PWR plants. Some considerations on French code RSEM and feedback from operations

International Nuclear Information System (INIS)

Carnus, M.; Bonan, C.; Ould, P.

2015-01-01

When utilities have to repair components or equipment using weld process it is often not possible to comply with requirements which have been used for original design and manufacturing. French code RSEM (In service inspection rules for mechanical components of PWR nuclear islands) for maintenance operations includes specific requirements for such situations. A quick overview of some of these requirements is given in this paper. Several cases are discussed. First, requirements have been included in RSEM code for partial or full repair of austenitic stainless steel cladding on low alloy steel Pressure Vessel components. These include recommendations for weld repair and operation. Such repairs may be encountered on steam generator channel head cladding, or internals core junction cladding. An example of such a repair is given in this paper. Secondly, the state of the art is to eliminate HAZ (Heat Affected Zone) of previous weld before maintenance operation to avoid multiple affectation of HAZ at same location. This is not always possible. Weld tests have been carried out on Carbon Steel plates in order to evaluate effect of multiple affectations on HAZ at same location. Test results show that carbon steel weld properties remain acceptable under test conditions. Thirdly, before operations, RSEM code requires testing to prove that weldability of materials whose properties have been drastically degraded after a long service period is acceptable. The weldability of austenitic ferritic casting under simulated aging conditions, has been evaluated on different mockups by AREVA NP, results show that the weldability remains acceptable

Fracture toughness properties of candidate canister materials for spent fuel storage by concrete cask

International Nuclear Information System (INIS)

Arai, Taku; Mayuzumi, Masami; Libin, Niu; Takaku, Hiroshi

2005-01-01

It is very significant to clarify the fracture toughness properties of candidate canister materials to ensure the structural integrity against the accidents during handling in the storage facility. Fracture toughness tests on the CT specimens cut from base metal, heat affected zone (HAZ) and weld metal in the 2 types of weld joints made by candidate canister materials (SUS329J4L duplex stainless steel and YUS270 super stainless steel) were conducted under various test temperature between 233K and 473K. Stable ductile crack extensions were observed in all of the specimens. The fracture toughness J Q of the base metal and the HAZ of SUS329L4L showed the smallest value at 233K, and increased with temperature, then reached to the largest value at 298K. At the higher temperature, the value of J Q decreased slightly with temperature. While, the value of J Q in the weld metal increased with temperature. The value of J Q of YUS270 increased with temperature. The values of J Q for weld metal in both of the materials were not greater than those in base metal and HAZ at each test temperature. The values of J Q in weld metal of both materials at 213K and 473K were greater than applied J derived from postulated semi-elliptical surface flaw and maximum allowable stress in JSME design coed. This result suggested that these materials have enough toughness for use as the canister material. (author)

30 CFR 47.21 - Identifying hazardous chemicals.

Science.gov (United States)

2010-07-01

..., subpart Z, Toxic and Hazardous Substances. (4) American Conference of Governmental Industrial Hygienists... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Identifying hazardous chemicals. 47.21 Section... TRAINING HAZARD COMMUNICATION (HazCom) Hazard Determination § 47.21 Identifying hazardous chemicals. The...

Environmental Training Modules. Module 3 - Shipyard Incident Response Training

Science.gov (United States)

1999-05-01

oxidizing or through fermentation ). • Absorption of oxygen (caused by the vessel itself or the contents stored in it). Shipyard HazMat Technician...environmental effects • May be difficult to find in bulk quantities. • * Dilute acetic acid ( vinegar ) Caustic spills have routinely been neutralized with

Variability in heat strain in fully encapsulated impermeable suits in different climates and at different work loads

NARCIS (Netherlands)

Hartog, E.A. den; Rubenstein, C.D.; Deaton, A.S.; Bogerd, C.P.

2017-01-01

A major concern for responders to hazardous materials (HazMat) incidents is the heat strain that is caused by fully encapsulated impermeable (NFPA 1991) suits. In a research project, funded by the US Department of Defense, the thermal strain experienced when wearing these suits was studied. Forty

Fluid replacement advice during work in fully encapsulated impermeable chemical protective suits

NARCIS (Netherlands)

Rubenstein, C.D.; Hartog, E.A. den; Deaton, A.S.; Bogerd, C.P.; Kant, S. de

2017-01-01

A major concern for responders to hazardous materials (HazMat) incidents is the heat strain that is caused by fully encapsulated impermeable chemical protective suits. In a research project, funded by the US Department of Defense, the thermal strain experienced when wearing these suits was studied.

Hardening and stress relaxation during repeated heating of 15Kh2MFA and 15Kh2NMFA steels welded joints

International Nuclear Information System (INIS)

Zubchenko, A.S.; Suslova, E.A.

1986-01-01

Results of investigation of temperature-time conditions of hardening of welded joints of 15Kh2MFA and 15Kh2NMFA steels and their relaxation resistance, effect of metal structure of imitated heat affected zone (HAZ) on intensity of precipitation hardening at repeated heating are presented as well as the results of the process of relaxation of residual stresses at welded joints samples heating carried out by automatic welding under the flux with the use of adding materials and technology of manufacturing of vessels of WWER-440 and WWER-1000 reactors. Peculiarities of the hardening at repeated heating of the HAZ metal imitated at these steels. Precipitation hardening of overheated 15Kh2MFA steel is connected with precipitations at repeated heating of carbides of the M 7 C 3 , M 3 C and VC type. Stress relaxation in welded joints runs more intensively at the initial stage of repeated heating, i.e. during the same period of the process of dispersed carbide precipitations

Microstructural Study of 17-4PH Stainless Steel after Plasma-Transferred Arc Welding.

Science.gov (United States)

Deng, Dewei; Chen, Rui; Sun, Qi; Li, Xiaona

2015-01-29

The improvement of the surface qualities and surface hardening of precipitation hardened martensitic stainless steel 17-4PH was achieved by the plasma-transferred arc welding (PTAW) process deposited with Co-based alloy. The microstructure of the heat affected zone (HAZ) and base metal were characterized by optical microscope (OM), scanning electron microscope (SEM) and transmission electron microscope (TEM). The results show that there are obvious microstructural differences between the base metal and HAZ. For example, base material is transformed from lath martensite to austenite due to the heateffect of the welding process. On the other hand, the precipitate in the matrix (bar-like shape Cr₇C₃ phase with a width of about one hundred nanometres and a length of hundreds of nanometres) grows to a rectangular appearance with a width of about two hundred nanometres and a length of about one micron. Stacking fault could also be observed in the Cr₇C₃ after PTAW. The above means that welding can obviously improve the surface qualities.

Lepidosaphes gloverii (Hemiptera: Diaspididae, Estudios Biológicos y Ecológicos en Cítricos de Cuba

Directory of Open Access Journals (Sweden)

Caridad GONZÁLEZ

2005-01-01

Full Text Available Se estudió la distribución espacial y temporal de Lepidosaphes gloverii (Pack. y sus biorreguladores sobre naranjo Valencia en Cuba. Fueron examinados brotes orientados hacia los cuatro puntos cardinales y en tres estratos de los árboles. Los estados de desarrollo de L. gloverii y la incidencia de los biorreguladores se contabilizaron en el haz y el envés de las hojas. Se estudió la biología del insecto en plantines de lima Persa, limón Eureka y naranjo Valencia. Un complejo de enemigos naturales fue inventariado: parasitoides, depredadores y hongos entomopatógenos, los que difieren por su ubicación en micro hábitats. Se observó la tendencia de la población a la agregación, así como mayores densidades poblacionales hacia el noroeste del campo, el norte del árbol, la zona central del brote y el haz de las hojas.

Microstructures and mechanical properties of friction stir welded dissimilar steel-copper joints

Energy Technology Data Exchange (ETDEWEB)

Jafari, M.; Abbasi, M.; Poursina, D.; Gheysarian, A. [University of Kashan, Kashan (Iran, Islamic Republic of); Bagheri, B. [Amirkabir University of Technology, Tehran (Iran, Islamic Republic of)

2017-03-15

Welding dissimilar metals by fusion welding is challenging. It results in welding defects. Friction stir welding (FSW) as a solid-state joining method can overcome these problems. In this study, 304L stainless steel was joined to copper by FSW. The optimal values of the welding parameters traverse speed, rotational speed, and tilt angle were obtained through Response surface methodology (RSM). Under optimal welding conditions, the effects of welding pass number on the microstructures and mechanical properties of the welded joints were investigated. Results indicated that appropriate values of FSW parameters could be obtained by RSM and grain size refinement during FSW mainly affected the hardness in the weld regions. Furthermore, the heat from the FSW tool increased the grain size in the Heat-affected zones (HAZs), especially on the copper side. Therefore, the strength and ductility decreased as the welding pass number increased because of grain size enhancement in the HAZs as the welding pass number increased.

Sensitization development in austenitic stainless steel piping

International Nuclear Information System (INIS)

Bruemmer, S.M.; Page, R.E.; Atteridge, D.G.

1984-10-01

Pacific Northwest Laboratory and the Division of Engineering Technology of the US Nuclear Regulatory Commission are conducting a program to determine a method for evaluating welded and rapair-welded stainless steel piping for light-water reactor service. Validated models, based on experimental data, are being developed to predict the degree of sensitization (DOS) and the intergranular stress corrosion cracking (IGSCC) susceptibility in the heat-affected zone (HAZ) of the SS weldments. The cumulative effects of material composition, past fabrication procedures, past service exposure, weldment thermomechanical (TM) history, and projected post-repair component life are being considered. This program will measure and model the development of HAZ TM history and resultant sensitized microstructure in welded and repair-welded piping. An empirical correlation between a material's DOS and its susceptibility to SCC will be determined using slow strain rate tensile tests. Mill heat chemistries and processing/fabrication records already required in the nuclear industry will be used as input for initial DOS predictions

Farklı Kaynak Yöntemleri İle Birleştirilen Doğalgaz Borularının İncelenmesi

OpenAIRE

KARA, Rıza; ÇOLAK, Fatih; YILDIRIM, Gökhan; HİÇYILMAZ, Vedat

2017-01-01

Doğalgaz kullanımının yaygınlaşması ile birlikte tesisat işlemlerinde kaynaklı birleştirme kalitesi önem kazanmıştır. Bu çalışmada çelik doğalgaz borularının kaynak kabiliyeti araştırılmıştır. Çalışmada API5L X52 kalite 1/2 inç yarıçapında 2,8 mm et kalınlığına sahip borular 100 mm boyutlarında hazırlanmıştır. Hazırlanan numuneler Oksi-Gaz, elektrik ark kaynağı ve MAG (Gaz altı) kaynak yöntemleriyle birleştirilmiştir. Farklı kaynak yöntemleriyle birleştirilen kaynaklı numuneler mikroyapı, ser...

Analysis of 3D Planar Laminations in a Welded Section of API 5L X52 Applying the Finite Element Method

Directory of Open Access Journals (Sweden)

Martin. J. Fernández-Cueto

Full Text Available Abstract The mechanical behavior of API 5L X52 steel with planar type laminations was studied in the present work. Planar laminations were proposed in the base metal (BM, heat affected zone (HAZ and welding bead (WB. Three-dimensional finite element (FE models, kinematic hardening and mechanical properties for BM, HAZ, and WB were activated in the finite element program. The results showed that crack propagation corresponds to the direction of the main stress. For a crack length (2a of 10.01 mm, crack propagation may occur at the right crack tip towards the outer wall of the BM. For 2a of 15.12 mm, crack propagation was located on the right crack tip and propagates to the inner wall. For 2a of 17.12 mm, crack propagation was observed at the left crack tip and propagates to the outer wall in the BM. The results achieved by FEM agree when compared with real laminations in API 5L pipelines.

A Comparison of Two Approaches to Safety Analysis Based on Use Cases

Science.gov (United States)

Stålhane, Tor; Sindre, Guttorm

Engineering has a long tradition in analyzing the safety of mechanical, electrical and electronic systems. Important methods like HazOp and FMEA have also been adopted by the software engineering community. The misuse case method, on the other hand, has been developed by the software community as an alternative to FMEA and preliminary HazOp for software development. To compare the two methods misuse case and FMEA we have run a small experiment involving 42 third year software engineering students. In the experiment, the students should identify and analyze failure modes from one of the use cases for a commercial electronic patient journals system. The results of the experiment show that on the average, the group that used misuse cases identified and analyzed more user related failure modes than the persons using FMEA. In addition, the persons who used the misuse cases scored better on perceived ease of use and intention to use.

Microstructure and mechanical properties in TIG welding of CLAM steel

International Nuclear Information System (INIS)

Zhu Qiang; Lei Yucheng; Chen Xizhang; Ren Wenjie; Ju Xin; Ye Yimin

2011-01-01

Tungsten insert gas (TIG) welding on China low activation martensitic (CLAM) steel under identical conditions was performed. Microhardness test, tensile test, Charpy impact test and microstructure measurements were carried out on TIG welded joints after post weld heat-treatment. Hardening at WM and softening in HAZ is detected in the TIG weld joint. Microhardness in WM decreased when the temperature of PWHT increased. The ultimate tensile stress of weld metal is higher than that of HAZ and BM. Absorbed energy increased with PWHT temperature rising, until PWHT was done at 760 deg. C/30 min, the specimen ductile fractured in local area. The microstructure of the weld metal for every specimen was found to be tempered martensite with a little of delta ferrite. M 23 C 6 particles are the predominant type of carbides. Oxide precipitate phases appeared in WM, which are the primary crack initiation sites and it is critically important minimize their formation.

Verification of Strength of the Welded Joints by using of the Aramis Video System

Directory of Open Access Journals (Sweden)

Pała Tadeusz

2017-03-01

Full Text Available In the paper are presented the results of strength analysis for the two types of the welded joints made according to conventional and laser technologies of high-strength steel S960QC. The hardness distributions, tensile properties and fracture toughness were determined for the weld material and heat affect zone material for both types of the welded joints. Tests results shown on advantage the laser welded joints in comparison to the convention ones. Tensile properties and fracture toughness in all areas of the laser joints have a higher level than in the conventional one. The heat affect zone of the conventional welded joints is a weakness area, where the tensile properties are lower in comparison to the base material. Verification of the tensile tests, which carried out by using the Aramis video system, confirmed this assumption. The highest level of strains was observed in HAZ material and the destruction process occurred also in HAZ of the conventional welded joint.

Effect of the weld thermal cycles by the modified indirect electric arc (MIEA) on the mechanical properties of the AA6061-T6 alloy

International Nuclear Information System (INIS)

Ambriz, R. A.; Barrera, G.; Garcia, R.; Lopez, V. H.

2009-01-01

Results of temperature measurements during welding of 12.7 mm thick AA6061-T6 alloy plates by modified indirect electric arc (MIEA) are presented. This study describes the thermal cycles of the heat affected zone (HAZ) and also in the fusion zone. Depending upon the position of the transducers, the maximum temperatures measured in the HAZ range from 308 to 693 degree centigrade, these measurements were related with the tensile test results, and the failure zone reported previously by the authors. It was observed that, there is a decrease in the mechanical strength of the welded joints, due to the microstructural changes suffered by AA6061-T6 alloy in which formation of the βoccurs according to the TTT transformation diagram. The inherent cooling conditions of the weld pool observed for the MIEA technique (only one pass of welding), have permitted to establish the characteristics of solidification and microstructure for a specific cooling rate. (Author) 24 refs

Evaluation of base material and welded joints designated for membrane wall components made from low-alloy steels in large boilermaker conditions

Energy Technology Data Exchange (ETDEWEB)

Dobrzanski, Janusz; Zielinski, Adam [Institute for Ferrous Metallurgy, Gliwice (Poland); Pasternak, Jerzy [Boiler Engineering Company RAFAKO S.A., Raciborz (Poland)

2010-07-01

Supercritical operating parameters of lower emission power units require novel creep resisting steels. Therefore, this paper constains selected information, results of collectors made from the new low-alloy bainitic creep-resistant steels as 7CrWVNb9-6(P23) and 7CrMoVTiB10-10(P24) performed in large boilermaker conditions. The research and implementation process includes: - evaluation, comparison of requested properties of base material and welded joints as tensile strength, impact strength and technological properties, - destructive examinations with evaluation of welded joints and HAZ structure and hardness distribution, - evaluation of creep resistance properties and structure stability after heat treatments and again process of base material, HAZ and welded joints, - influence of manufacturing process in large boilermaker conditions and after simulated operation. A new creep-resistant steels to be used, in order to comply with the operational requirements, as to assure the appropriate reliability and safety of the boiler equipment in operation process. (orig.)

Residual strains and microstructure development in single and sequential double sided friction stir welds in RQT-701 steel

Energy Technology Data Exchange (ETDEWEB)

Barnes, S.J. [School of Materials, University of Manchester, Grosvenor Street, Manchester M1 7HS (United Kingdom)], E-mail: simon.barnes-2@manchester.ac.uk; Steuwer, A. [FaME38, ILL ESRF, 6 rue J.Horowitz, 38042 Grenoble, Cedex (France); University of Plymouth, Drake Circus, Plymouth PL4 8AA (United Kingdom); Mahawish, S. [School of Materials, University of Manchester, Grosvenor Street, Manchester M1 7HS (United Kingdom); Johnson, R. [TWI Yorkshire, Wallis Way, Catcliffe, Rotherham S60 5TZ (United Kingdom); Withers, P.J. [School of Materials, University of Manchester, Grosvenor Street, Manchester M1 7HS (United Kingdom)

2008-09-25

Single and double sided partial penetration friction stir butt welds, in a rolled, quenched and tempered steel (RQT-701), were produced at The Welding Institute (TWI) under controlled process conditions. The residual strain distributions in the longitudinal and transverse directions have been measured using energy dispersive synchrotron X-ray diffraction. The measured strains were indicative of longitudinal tensile residual stresses at levels greater than the 0.2% yield stress of the parent metal in both the single and double pass welds. In both cases, the maximum tensile strain was found in the parent metal at the boundary of the heat affected zone (HAZ). Microstructural analysis of the welds was carried out using optical microscopy and hardness variations were also mapped across the weld-plate cross-section. The maximum hardness was observed in the mixed bainite/martensite structure of the weld nugget on the advancing side of the stir zone. The minimum hardness was observed in the HAZ.

Heat affected zone liquation cracking in electron beam welded third generation nickel base superalloys

International Nuclear Information System (INIS)

Ojo, O.A.; Wang, Y.L.; Chaturvedi, M.C.

2008-01-01

The weldability of directionally solidified nickel base superalloy TMS-75 and TMS-75+C was investigated by autogenous bead-on-plate electron beam welding. The analysis of microsegregation that occurred during solidification of the as-cast alloys indicated that while W and Re segregated into the γ dendrites of both the alloys, Ta, Hf and C were rejected into the interdendritic liquid in the TMS-75+C. Heat affected zone intergranular liquation cracking was observed in both the materials and was observed to be closely associated with liquated γ-γ' eutectic microconstituent. The TMS-75+C alloy, however, exhibited a reduced extent of HAZ cracking compared to TMS-75. Suppression of terminal solidification reaction involving non-invariant γ-γ' eutectic transformation due to modification of primary solidification path by carbon addition is suggested to be an important factor contributing to reduced susceptibility of TMS-75+C alloy to HAZ liquation cracking relative to the TMS-75 superalloy

Effect of the weld thermal cycles by the modified indirect electric arc (MIEA) on the mechanical properties of the AA6061-T6 alloy; Efecto de los ciclo termicos de soldadura por arco electrico indirecto modificado (AEIM) en las propiedades mecanicas de la aleacion AA6061-T6

Energy Technology Data Exchange (ETDEWEB)

Ambriz, R. A.; Barrera, G.; Garcia, R.; Lopez, V. H.

2009-07-01

Results of temperature measurements during welding of 12.7 mm thick AA6061-T6 alloy plates by modified indirect electric arc (MIEA) are presented. This study describes the thermal cycles of the heat affected zone (HAZ) and also in the fusion zone. Depending upon the position of the transducers, the maximum temperatures measured in the HAZ range from 308 to 693 degree centigrade, these measurements were related with the tensile test results, and the failure zone reported previously by the authors. It was observed that, there is a decrease in the mechanical strength of the welded joints, due to the microstructural changes suffered by AA6061-T6 alloy in which formation of the {beta}occurs according to the TTT transformation diagram. The inherent cooling conditions of the weld pool observed for the MIEA technique (only one pass of welding), have permitted to establish the characteristics of solidification and microstructure for a specific cooling rate. (Author) 24 refs.

Development of liquid-nitrogen-cooling friction stir spot welding for AZ31 magnesium alloy joints

Science.gov (United States)

Wu, Dong; Shen, Jun; Zhou, Meng-bing; Cheng, Liang; Sang, Jia-xing

2017-10-01

A liquid-nitrogen-cooling friction stir spot welding (C-FSSW) technology was developed for welding AZ31 magnesium alloy sheets. The liquid-nitrogen cooling degraded the deformability of the welded materials such that the width of interfacial cracks increased with increasing cooling time. The grain size of the stirred zone (SZ) and the heat-affected zone (HAZ) of the C-FSSW-welded joints decreased, whereas that of the thermomechanically affected zone (TMAZ) increased with increasing cooling time. The maximum tensile shear load of the C-FSSW-welded joints welded with a cooling time of 5 or 7 s was larger than that of the friction stir spot welding (FSSW)-welded joint, and the tensile shear load decreased with increasing cooling time. The microhardness of the C-FSSW-welded joints was greater than that of the FSSW-welded joint. Moreover, the microhardness of the SZ and the HAZ of the C-FSSW-welded joints increased, whereas that of the TMAZ decreased, with increasing cooling time.

Stress corrosion cracking resistance of 22% Cr duplex stainless steel in simulated sour environments

International Nuclear Information System (INIS)

Kudo, T.; Tsuge, H.; Moroishi, T.

1989-01-01

This paper reports the effect of nickel and nitrogen contents on stress corrosion cracking (SCC) of 22%Cr - 3%Mo-base duplex stainless steel investigated in simulated sour environments with respect to both the base metal and the heat-affected zone (HAZ) of welding. The threshold stress and the critical chloride concentration for SCC were evaluated as a function of the ferrite content (α-content) in the alloy. The threshold stress is highest at the α-content of 40 to 45%, and is lowered with decreasing and increasing the α-content from its value. The alloy whose α-content exceeds 80% at the HAZ has also high susceptibilities to pitting corrosion and intergranular corrosion (ICG). The critical chloride concentration for cracking increases with the decrease in the α-content. Moreover, the contents of chromium, nickel and molybdenum in the α-phase are considered to be an important factor for determining the critical chloride concentration

Boundary and sub-boundary hardening in high-Cr ferritic steels during long-term creep at 650 C

Energy Technology Data Exchange (ETDEWEB)

Abe, F. [National Institute for Materials Science (NIMS) (Japan)

2008-07-01

The sub-boundary hardening is shown to be the most important strengthening mechanism in creep of the 9% Cr steel base metal and welded joints. The addition of boron reduces the coarsening rate of M{sub 23}C{sub 6} carbides along boundaries near prior austenite grain boundaries during creep, enhancing the sub-boundary hardening. This improves long-term creep strength. The enhancement of boundary and subboundary hardening by fine distribution of precipitates along boundaries is significantly reduced in fine-grained region of Ac{sub 3} HAZ simulated specimens of conventional steels P92 and P122. In NIMS 9% Cr boron steel welded joints, the grain size and distribution of carbonitrides are substantially the same between the HAZ and base metal, where fine carbonitrides are distributed along the lath and block boundaries as well as along prior austenite grain boundaries. This is essential for the suppression of Type IV fracture in NIMS 9% Cr boron steel welded joints. (orig.)

Laser welding study for further development in essential power plant part repairs

Directory of Open Access Journals (Sweden)

Isarawit Chaopanich

2015-06-01

Full Text Available The objective of this research work was to study the effects of laser welding when compared with shield metal arc welding (SMAW process on the heat input, welded deposit rate, residual stress, distortion, microstructure and micro hardness. The martensitic stainless steel grade 431 specimens were overlay welded with the stainless steel filler metals. From the results, the heat input of 0.26 kJ/mm in laser welding calculated was significantly lower than that of 1.66 kJ/mm in SMAW, and contributed to low level residual stress, minimal distortion, very small penetration depth and heat affected zone (HAZ of less than 100 µm. The micro hardness results indicated that the maximum value from laser welding in the HAZ was 370.2 HV lower than the value from SMAW of 525.5 HV. The welded deposit rate for laser welding was with 26.5 mm3 /min remarkably lower than the rate for SMAW of 1,800 mm3 /min.

Residual strains and microstructure development in single and sequential double sided friction stir welds in RQT-701 steel

International Nuclear Information System (INIS)

Barnes, S.J.; Steuwer, A.; Mahawish, S.; Johnson, R.; Withers, P.J.

2008-01-01

Single and double sided partial penetration friction stir butt welds, in a rolled, quenched and tempered steel (RQT-701), were produced at The Welding Institute (TWI) under controlled process conditions. The residual strain distributions in the longitudinal and transverse directions have been measured using energy dispersive synchrotron X-ray diffraction. The measured strains were indicative of longitudinal tensile residual stresses at levels greater than the 0.2% yield stress of the parent metal in both the single and double pass welds. In both cases, the maximum tensile strain was found in the parent metal at the boundary of the heat affected zone (HAZ). Microstructural analysis of the welds was carried out using optical microscopy and hardness variations were also mapped across the weld-plate cross-section. The maximum hardness was observed in the mixed bainite/martensite structure of the weld nugget on the advancing side of the stir zone. The minimum hardness was observed in the HAZ

Osmanlı Seferlerinde Organizasyon Ve Lojistik The Organization And Logistics Of The Ottoman Flights

Directory of Open Access Journals (Sweden)

Uğur KURTARAN

2012-12-01

sefer öncesinde ne şekilde organize edildiğini ve ihtiyaçlarının nasıl karşılandığını anlamak, devletin kuruluş ve yükselişindeki temel sebeplerin yanı sıra, yıkılışının sebeplerinin de daha iyi anlaşılması bakımından oldukça önemlidir. Çünkü tarih boyunca kurulmuş olan diğer devletler gibi Osmanlı Devleti’nin de siyasi tarihi ve gelişimi askerî operasyonlarına bağlı olarak şekillenmiştir. Askeri operasyonlarının başarılı olması ise sefer öncesi uygulanan lojistik faaliyetleri, yapılan hazırlıklar ve organizasyonlarına bağlıdır. Nitekim Osmanlı Devleti herhangi bir savaşa karar verdiğinde yurt içindeki idarî ve lojistik teşkilâtın daha etkin bir düzeye çıkarılması için önemli hazırlıklar yapmıştır. Günümüzde lojistik olarak isimlendirilen bu sefer öncesi hazırlıklar ve uygulanan stratejiler Osmanlı Devleti’nde yapılan seferlerin başarılı olmasını sağlamıştır. Bu noktada devletin büyümesinde ve sınırlarının genişlemesinde seferler öncesinde uygulanan bu hazırlıkların büyük bir etkisi vardır. Yani Osmanlı Devleti’ne tarih boyunca savaşları kazandıran ya da kaybettiren temel unsur çağdaşı diğer devletlerden çok daha iyi uyguladığı savaş öncesi hazırlıklar ve organizasyonlardır. Bu hazırlıkların Osmanlı Devleti tarafından nasıl ve şekilde uygulandığı bilmek Osmanlı seferlerine olan bakış açımızı genişleterek Osmanlı zaferlerinin altında yatan temel sebepleri daha iyi anlamımızı sağlayacaktır. Bu çalışma bu hedef ve amaçlar doğrultusunda hazırlanmıştır. Çalışmada Osmanlıların savaş öncesi ve savaş sırasındaki hazırlıklarını ne şekilde yaptığını ortaya koymak ve bu konudaki mevcut bilgi ve birikimlere yeni kaynakların ışığında farklı bir bakış açısı kazandırmk amaçlamaktadır.

30 CFR 47.51 - Requirement for an MSDS.

Science.gov (United States)

2010-07-01

... Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR EDUCATION AND TRAINING HAZARD COMMUNICATION (HazCom) Material Safety Data Sheets (MSDS) § 47.51 Requirement for an MSDS. Operators must have... from mining or milling if its hazards are already addressed on the MSDS of the source chemical. ...

Seismic microzonation of Bangalore, India

Indian Academy of Sciences (India)

Evaluation of seismic hazards and microzonation of cities enable us to characterize the potential seismic areas which have similar exposures to haz- ards of earthquakes, and these results can be used for designing new structures or retrofitting the existing ones. Study of seismic hazard and preparation of microzonation ...

Hazards evaluation of plutonium metal opening and stabilization

International Nuclear Information System (INIS)

JOHNSON, L.E.

1999-01-01

Hazards evaluation is the analysis of the significance of hazardous situations associated with an activity OK process. The HE used qualitative techniques of Hazard and Operability (HazOp) analysis and What-If analysis to identify those elements of handling and thermal stabilization processing that could lead to accidents

Urgent medical response in CBR incidents

International Nuclear Information System (INIS)

Castulik, P.; Slabotinsky, J.; Kralik, L.; Bradka, S.

2009-01-01

During CBR incidents with releases of hazardous materials (HazMat), there is extremely urgent aim of first rescuing responders to safe the life for as much as possible victims and reducing health consequences from the exposure of the HazMat. Highest priority of the response is to be applied, if victims are exposed with chemicals through their airways and/or mucous membranes. There is general approach in the emergency medical services (EMS) stated that the victims being in critical status have to receive emergency medical care on-site even prior the transportation to a medical facility. However, in a case of CBR events the EMS prefer to provide the First Aid for victims to be already decontaminated as mass casualties, e.g. by the firemen and transferred to a safe zone. This approach is to be time consuming and thus creating delays in medical care not in the favor of a victim's successful survival. In order to overcome this approach, there are needs for eminent ceasing of the victims exposure, protection of breathing tract/ventilation support and administration of antidotes, if available. All this have to be done in shortest time since HazMat incident/accident occurs. This presentation is focusing on emergency provisions for saving victims directly in contaminated environment through the assistance by responders, concentrating on search and rescue of victims, their emergency decontamination, breathing protection, clothing removal, ventilation support, antidote administration, fixing and bandage of trauma injuries prior transportation and/or mass decontamination. This experience is shared based on a field exercise with the EMS volunteers (Red Cross), fire brigade volunteers and university's students.(author)

Microstructural characterization of laser and electron beam (EB) welds of Nb-1Zr-0.1C alloy

International Nuclear Information System (INIS)

Badgujar, B.P.; Tewari, R.; Dey, G.K.; Samajdar, I.

2015-01-01

Nb-1wt%Zr-0.1wt%C alloy is being considered for the structural applications in proposed Compact High Temperature Reactor (CHTR) on account of its excellent combination of high temperature properties. The applications of this alloy calls for welding, which is a difficult task due to its reactive nature, higher thermal conductivity and melting point. The high energy density techniques like laser and electron beam were employed to produce the welds on sheets of Nb-alloy at various processing parameters in bead-on-plate and square butt joint configurations. The weld joints produced were characterized by studying their optical, Scanning Electron Microscopy (SEM) and Electron Back Scattering Diffraction (EBSD) micro-graphs. The SEM micrograph of EB fusion zone along with the heat affected zone (HAZ) and the base region were studied and abrupt changes in the grain morphology were found in each zone. The fusion zone shows larger grains indicating the rapid grain growth after solidification, whereas the HAZ shows relatively smaller size of the grains but still much larger than the base zone. The SEM micrograph of central part of the same butt weld shows clear grain boundaries with a large variation in the grain size (45-82 micrometer) in the weld region. The heat affected zone (HAZ) and base metal showed fine carbide precipitates along the grain boundaries, whereas carbides were found dissolved in the weld zone. The EBSD micrograph of electron beam fusion zone describing the grain orientation in the weld region are described. The micro-hardness profile across the width of welds was also studied. The detailed results of all these studies are described in this paper. (author)

Impact Toughness of Subzones in the Intercritical Heat-Affected Zone of Low-Carbon Bainitic Steel

Directory of Open Access Journals (Sweden)

Zhenshun Li

2018-06-01

Full Text Available The subzones of the intercritical heat-affected zone (IC HAZ of low-carbon bainitic steel were simulated by using a Gleeble-3500 simulator to study the impact toughness. The results showed that the IC HAZ is not entirely brittle and can be further divided into three subzones according to the impact toughness or peak welding temperature; the invariant subzone heated between the critical transformation start temperature (Ac1 and 770 °C exhibited unchanged high impact toughness. Furthermore, an extremely low impact toughness was found in the embrittlement subzone, heated between 770 and 830 °C, and the reduction subzone heated between 830 °C and the critical transformation finish temperature (Ac3 exhibited toughness below that of the original metal. The size of the blocky martensite-austenite (M-A constituents was found to have a remarkable level of influence on the impact toughness when heated below 830 °C. Additionally, it was found that, once the constituent size exceeds a critical value of 3.0 µm at a peak temperature of 770 °C, the IC HAZ becomes brittle regardless of lath or twinned martensite constitution in the M-A constituent. Essentially, embrittlement was observed to occur when the resolved length of initial cracks (in the direction of the overall fracture formed as a result of the debonding of M-A constituents exceeding the critical Griffith size. Furthermore, when the heating temperature exceeded 830 °C, the M-A constituents formed a slender shape, and the impact toughness increased as the area fraction of the slender M-A constituents decreased.

Modelización del perfil de soldadura y de la cavidad de vapor en la aleación de aluminio 5182 soldada con láser

Directory of Open Access Journals (Sweden)

Pastor, M.

2001-12-01

Full Text Available The purpose of this research is the study of the laser welding process of the aluminum alloy 5182 and the development of models by means of the COSMOS/M package, in order to predict the shape of the keyhole and the temperatures profile of the weld. Modeling has been done considering the degree of defocusing. The heat flow applied on the models was a Gauss flow, considering the condition of the focused face and the conditions of negative and positive defocusing. The validity of the models has been demonstrated comparing their results with those obtained by experimental tests. The extent of defocusing of laser beam affected the stability of the keyhole and welding geometry.

El presente trabajo se introduce en el desarrollo de modelos para predecir la forma de la cavidad de vapor y el perfil de la aleación de aluminio 5182 con soldadura láser. Para el procesamiento del modelo se ha empleado el paquete profesional de Elementos Finitos COSMOS/M. La modelización de la soldadura se realizó considerando como variable el grado de desenfoque del haz de láser y la distribución del flujo de calor según un modelo Gaussiano, para las condiciones de haz enfocado y de desenfoque negativo y positivo. La validez de los resultados obtenidos se comprobó mediante la comparación con los resultados obtenidos en pruebas experimentales, concluyéndose que el grado de desenfoque del haz del láser afecta notablemente la estabilidad de la cavidad de vapor y la geometría de la soldadura.

Lower waist circumference in mildly-stunted adolescents is associated with elevated insulin concentration.

Science.gov (United States)

Clemente, Ana Paula Grotti; Santos, Carla Danusa da Luz; Martins, Vinicius J B; Albuquerque, Maria Paula; Fachim, Mariana B; Sawaya, Ana Lydia

2014-01-01

Augmented waist circumference (WC) is associated with non-communicable diseases and could represent a valuable marker in screening for metabolic dysfunctions in subjects with insufficient linear growth. The objective of the present study was to determine whether biochemical and hemodynamic parameters and waist circumference vary between mildly-stunted and non-stunted adolescents from impoverished communities of São Paulo, Brazil. The cross-sectional study involved 206 subjects, aged between 9 and 19 years and living in impoverished areas of São Paulo, Brazil. The sample population was divided according to height-for-age Z-score (HAZ) into stunted (-1 > HAZ ≥ -2) and non-stunted (HAZ ≥ -1) groups, and was sub-divided according to gender. Logistic regression analysis was employed to compare individuals with elevated (> 75th percentile) insulin concentrations. The receiver operating characteristic curves were constructed to determine WC cut-off points that could be used to identify stunted and non-stunted individuals with elevated insulin concentrations. WC cut-off points of 58.25cm and 67.2cm allowed for correct classification of 90.7% of stunted and 88.7% of non-stunted individuals in the studied population. While the sensitivity of the model was high for stunted and non-stunted subjects (98.8% and 97.2%, respectively), the specificity was modest (57.1% and 41.2%, respectively). The results presented herein suggest that an increase in plasma insulin is one of the primary metabolic modifications in stunted individuals, and that this alteration could be identified at a lower WC cut-off point than in non-stunted counterparts. Copyright © 2014 Sociedade Brasileira de Pediatria. Published by Elsevier Editora Ltda. All rights reserved.

Lower waist circumference in mildly-stunted adolescents is associated with elevated insulin concentration

Directory of Open Access Journals (Sweden)

Ana Paula Grotti Clemente

2014-09-01

Full Text Available Objective: Augmented waist circumference (WC is associated with non-communicable diseases and could represent a valuable marker in screening for metabolic dysfunctions in subjects with insufficient linear growth. The objective of the present study was to determine whether bio-chemical and hemodynamic parameters and waist circumference vary between mildly-stunted and non-stunted adolescents from impoverished communities of São Paulo, Brazil. Methods: The cross-sectional study involved 206 subjects, aged between 9 and 19 years and living in impoverished areas of São Paulo, Brazil. The sample population was divided according to height-for-age Z-score (HAZ into stunted (−1 > HAZ ≥ −2 and non-stunted (HAZ ≥ −1 groups, and was sub-divided according to gender. Logistic regression analysis was employed to compare individuals with elevated (> 75th percentile insulin concentrations. The receiver operating characteristic curves were constructed to determine WC cut-off points that could be used to identify stunted and non-stunted individuals with elevated insulin concentrations. Results: WC cut-off points of 58.25 cm and 67.2 cm allowed for correct classification of 90.7% of stunted and 88.7% of non-stunted individuals in the studied population. While the sensitivity of the model was high for stunted and non-stunted subjects (98.8% and 97.2%, respectively, the specificity was modest (57.1% and 41.2%, respectively. Conclusion: The results presented herein suggest that an increase in plasma insulin is one of the primary metabolic modifications in stunted individuals, and that this alteration could be identified at a lower WC cut-off point than in non-stunted counterparts.

Birth Weight, Nutritional Status and Body Composition among Malaysian Children Aged 7 to 10 Years

International Nuclear Information System (INIS)

Poh, Bee Koon; Ang, Yeow Nyin

2014-01-01

Full text: Studies have indicated that lower birth weight is associated with lower body mass index, but the use of birth weight in predicting later nutritional status and adiposity remains inconsistent. Hence, this paper aimed to examine the relationship between birth weight and nutritional status with body composition among Malaysian children. This study is part of the Nutritional Survey of Malaysian Children, which is part of the four-country South East Asian Nutrition Surveys (SEANUTS). Subjects comprising 398 boys and 389 girls from the main ethnic groups, namely Malays, Chinese, Indians, Sabah and Sarawak natives, were recruited using a stratified random sampling. Anthropometric measurements comprised body weight, height, waist circumference (WC) and body fat (BF). Body mass index (BMI), fat mass index (FMI) and fat-free mass index (FFMI) adjusted with height were included, and birth weight was obtained by parental report. Nutritional status such as weight-for-age (WAZ), height-for-age (HAZ) and BMI-for-age (BAZ) were determined using the WHO growth reference for 5–19 years. Physical activity level was assessed using the Physical Activity Questionnaire for Children. Mean birth weight, height, weight, and BF were 3.1±0.5kg, 128.0±8.1cm, 28.4±8.9kg, and 27.9±9.1% respectively. Boys (20.4±4.2kg) had higher FFM (p 4.0kg) (WAZ: 0.51±1.35; HAZ: -0.07 ± 0.67) at p<0.05. Besides, there were significant differences in weight, height, BAZ, FFM and FFMI between birth weight groups. Birth weight has weak correlation (p<0.01) with FFM (r = 0.22), WAZ (r = 0.21), HAZ (r = 0.20), BAZ (r = 0.18) and WC (r = 0.14). After adjusting for covariates, we found that higher birth weight was associated with significant higher values in all anthropometric measurements (p<0.01), especially WC (β = 2.82, p<0.001). Multiple regression analysis also indicated that birth weight positively predicted later nutritional status; 1kg increase in birth weight predicted 0.70, 0.46, and 0

Rural-urban disparities in child nutrition in Bangladesh and Nepal.

Science.gov (United States)

Srinivasan, Chittur S; Zanello, Giacomo; Shankar, Bhavani

2013-06-14

The persistence of rural-urban disparities in child nutrition outcomes in developing countries alongside rapid urbanisation and increasing incidence of child malnutrition in urban areas raises an important health policy question - whether fundamentally different nutrition policies and interventions are required in rural and urban areas. Addressing this question requires an enhanced understanding of the main drivers of rural-urban disparities in child nutrition outcomes especially for the vulnerable segments of the population. This study applies recently developed statistical methods to quantify the contribution of different socio-economic determinants to rural-urban differences in child nutrition outcomes in two South Asian countries - Bangladesh and Nepal. Using DHS data sets for Bangladesh and Nepal, we apply quantile regression-based counterfactual decomposition methods to quantify the contribution of (1) the differences in levels of socio-economic determinants (covariate effects) and (2) the differences in the strength of association between socio-economic determinants and child nutrition outcomes (co-efficient effects) to the observed rural-urban disparities in child HAZ scores. The methodology employed in the study allows the covariate and coefficient effects to vary across entire distribution of child nutrition outcomes. This is particularly useful in providing specific insights into factors influencing rural-urban disparities at the lower tails of child HAZ score distributions. It also helps assess the importance of individual determinants and how they vary across the distribution of HAZ scores. There are no fundamental differences in the characteristics that determine child nutrition outcomes in urban and rural areas. Differences in the levels of a limited number of socio-economic characteristics - maternal education, spouse's education and the wealth index (incorporating household asset ownership and access to drinking water and sanitation) contribute a

30 CFR 47.44 - Temporary, portable containers.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Temporary, portable containers. 47.44 Section... TRAINING HAZARD COMMUNICATION (HazCom) Container Labels and Other Forms of Warning § 47.44 Temporary, portable containers. (a) The operator does not have to label a temporary, portable container if he or she...

Influence of heat treatments for laser welded semi solid metal cast A356 alloy on the fracture mode of tensile specimens

CSIR Research Space (South Africa)

Kunene, G

2008-09-01

Full Text Available were then butt laser welded. It was found that the pre-weld as cast, T4 and post-weld T4 heat treated specimens fractured in the base metal. However, the pre-weld T6 heat treated specimens were found to have fractured in the heat affected zone (HAZ)...

Poesía del padre Briceño Jáuregui

Directory of Open Access Journals (Sweden)

Antonio J. Pérez H.

1963-03-01

Full Text Available En la Revista Javeriana (abril de 1962 apareció un haz de sonetos cincelados al pie mismo de los mármoles vetustos de Atica. Un poeta autóctono, virtuoso del clasicismo heleno, casi anónimo en meido de esta desazón literaria en que vivimos.

Microstructure and fatigue properties of Mg-to-steel dissimilar resistance spot welds

International Nuclear Information System (INIS)

Liu, L.; Xiao, L.; Chen, D.L.; Feng, J.C.; Kim, S.; Zhou, Y.

2013-01-01

Highlights: ► Mg/steel dissimilar spot weld had the same fatigue strength as Mg/Mg similar weld. ► Crack propagation path of Mg/Mg and Mg/steel welds was the same. ► Penetration of Zn into the Mg base metal led to crack initiation of Mg/steel weld. ► HAZ weakening and stress concentration led to crack initiation of Mg/Mg weld. -- Abstract: The structural application of lightweight magnesium alloys in the automotive industry inevitably involves dissimilar welding with steels and the related durability issues. This study was aimed at evaluating the microstructural change and fatigue resistance of Mg/steel resistance spot welds, in comparison with Mg/Mg welds. The microstructure of Mg/Mg spot welds can be divided into: base metal, heat affected zone and fusion zone (nugget). However, the microstructure of Mg/steel dissimilar spot welds had three different regions along the joined interface: weld brazing, solid-state joining and soldering. The horizontal and vertical Mg hardness profiles of Mg/steel and Mg/Mg welds were similar. Both Mg/steel and Mg/Mg welds were observed to have an equivalent fatigue resistance due to similar crack propagation characteristics and failure mode. Both Mg/steel and Mg/Mg welds failed through thickness in the magnesium sheet under stress-controlled cyclic loading, but fatigue crack initiation of the two types of welds was different. The crack initiation of Mg/Mg welds was occurred due to a combined effect of stress concentration, grain growth in the heat affected zone (HAZ), and the presence of Al-rich phases at HAZ grain boundaries, while the penetration of small amounts of Zn coating into the Mg base metal stemming from the liquid metal induced embrittlement led to crack initiation in the Mg/steel welds.

Association between Maternal and Child Nutritional Status in Hula, Rural Southern Ethiopia: A Cross Sectional Study.

Directory of Open Access Journals (Sweden)

Canaan Negash

Full Text Available Maternal and child under nutrition is highly prevalent in low-income and middle-income countries, resulting in substantial increases in mortality and overall disease burden. The aim of this baseline survey was to determine the association between selected maternal characteristics, maternal nutritional status and children's nutritional status.A survey with a cross sectional design was conducted between September and October 2012 in Hula, Ethiopia. The study subjects were 197 mothers of children between the ages of 6 and 23 months. Weight and height (mothers or recumbent length (children were measured using calibrated, standardized techniques. Seven percent of children were below -2 weight for height Z score (WHZ, 11.5% were below -2 height for age Z score (HAZ and 9.9% were below -2 weight for age Z score (WAZ. Maternal anthropometrics were associated with child nutritional status in the bivariate analysis. Maternal BMI (r = 0.16 P = 0.02 and educational status (r = 0.25 P = 0.001 were correlated with WHZ of children while maternal height (r = 0.2 P = 0.007 was correlated with HAZ of children. After multivariate analysis, children whose mothers had salary from employment had a better WHZ score (P = 0.001 and WAZ score (P<0.001. Both maternal BMI and maternal height were associated with WHZ (P = 0.04 and HAZ (P = 0.01 score of children.Having a mother with better nutritional status and salaried employment is a benefit for the nutritional status of the child. The interrelationship between maternal and child nutritional status stresses the value of improving maternal nutritional status as this should improve both maternal and child health outcomes. Therefore strategies to improve nutritional status of children should also include improving the nutritional status of the mother and empowering her financially.

ÇİMENTO ENJEKSİYONLARINDA KULLANILAN KATKI MALZEMELERİNİN REOLOJİK ÖZELLİKLERE ETKİLERİNİN ARAŞTIRILMASI

Directory of Open Access Journals (Sweden)

Özcan TAN

2004-02-01

Full Text Available Bu çalışmada farklı oranlardaki bentonit (B, uçucu kül (UK ve silis dumanı (SD ile birlikte hazırlanan enjeksiyon karışımlarının reolojik özellikleri araştırılmıştır. Deneyler için Taguchi Yöntemine göre 3 parametreli 4 seviyeli L16 deney tasarım tablosu seçilmiştir. Enjeksiyon karışımlarının hazırlanmasında, kullanılan katı ağırlığının % 0, % 0.5, % 1 ve % 3'ü oranlarında bentonit, % 10, % 20, % 30 ve % 40'ı oranlarında uçucu kül ve % 0, % 5, % 10 ve % 20'i oranlarında silis dumanı kullanılmıştır. Hazırlanan enjeksiyon karışımları için laboratuarda çökelme ve Marsh Hunisi deneyleri yapılmıştır. Deneyler su/katı (S/K 1.25 için yapılmış olup deney sonuçları Taguchi Yöntemine göre ayrı ayrı değerlendirilmiştir. Yapılan değerlendirmeler sonucunda; Akma süresi ve çökelme miktarı üzerinde en etkili parametrenin silis dumanı olduğu belirlenmiştir. Enjeksiyon karışımlarının incelenen özellikleri için optimum karışım oranları Taguchi Yöntemi ile belirlenmiş ve bu oranlar için doğrulama deneyleri yapılmıştır.

The impact of prenatal vitamin A and zinc supplementation on growth of children up to 2 years of age in rural Java, Indonesia.

Science.gov (United States)

Prawirohartono, Endy P; Nyström, Lennarth; Ivarsson, Anneli; Stenlund, Hans; Lind, Torbjörn

2011-12-01

To determine whether prenatal vitamin A and/or Zn supplementation affects postnatal growth. Follow-up of a randomized controlled trial monitoring growth in children from birth up to 24 months of age. Central Java, Indonesia. Children (n 343) of mothers participating in a double-blinded, randomized controlled study of vitamin A and/or Zn supplementation during pregnancy. We report the effects of prenatal supplementation on infant growth, measured as weight-for-age Z-scores (WAZ), height-for-age Z-scores (HAZ) and weight-for-height Z-scores (WHZ ), from 0 to 24 months, as well as differences in growth faltering among the supplementation groups. For HAZ, the absolute differences between the vitamin A-only and vitamin A + Zn groups at 3 and 9 months were 0·34 SD and 0·37 SD, respectively, and the absolute difference between the vitamin A-only and Zn-only groups at 18 months was 0·31 SD. Compared with placebo, none of the supplements affected growth. Defining growth faltering as a downward crossing of two or more major percentile lines, 50-75% of the children were found to be growth faltering within 9 months of age, whereas 17% and 8% scored <-2 SD for WAZ and HAZ, respectively. Prenatal supplementation did not reduce the prevalence of growth faltering. Prenatal vitamin A supplementation had a small but significant effect on postnatal growth of children's length until 18 months of age compared with supplementation with either vitamin A + Zn or Zn alone, but not compared with placebo. It had no effects on other anthropometric measures and did not reduce the prevalence of growth faltering. Future studies should duplicate these findings before recommendations can be made.

Investigation of residual stress in laser welding between carbon steel AISI 1010 and stainless AISI 304

International Nuclear Information System (INIS)

Mirim, Denilson de Camargo

2011-01-01

The dissimilar materials union has the residual stress formation as one of the most critical problems, which occurs mainly because these materials have both different thermal expansion coefficients and thermal conductivities. In this study, it was investigated the laser welding technique between steels, AISI 1010 and AISI 304. The materials were joined by butt autogenous welding with a continuous Nd:YAG laser. The main objective was to identify the welding parameters influence by the residual stresses analysis in the heat affected zone (HAZ). It was executed a factorial design with three-factor at two levels with a replica, which were varied power, welding speed and focal position of the laser beam. Residual stress measurements by the diffraction of X-rays were performed on the sample surface, to study their variation as a function of the parameters investigated. The blind hole method was also used to evaluate the residual stress along the samples depth, up to depth of 1mm. Besides residual stress measurement, weld seams were evaluated by optical and scanned electron microscopy, which were aimed to determine the weld geometry and changes in the microstructure. It was also made Vickers hardness measurements to evaluate the extent of HAZ. To evaluate the mechanical properties of the union were performed tensile and fatigue test. The MINITAB 15 software was used to analyze the residual stresses obtained by the blind hole method at different depths of the HAZ. It was also used statistical regression based on both the influences different and the combination of this input factors, in the residual stress of union. The results indicate that the models can satisfactorily predict the responses and provide users a guide to better define the welding parameters. (author)

Repair welding of fusion reactor components. Final technical report

International Nuclear Information System (INIS)

Chin, B.A.; Wang, C.A.

1997-01-01

The exposure of metallic materials, such as structural components of the first wall and blanket of a fusion reactor, to neutron irradiation will induce changes in both the material composition and microstructure. Along with these changes can come a corresponding deterioration in mechanical properties resulting in premature failure. It is, therefore, essential to expect that the repair and replacement of the degraded components will be necessary. Such repairs may require the joining of irradiated materials through the use of fusion welding processes. The present ITER (International Thermonuclear Experimental Reactor) conceptual design is anticipated to have about 5 km of longitudinal welds and ten thousand pipe butt welds in the blanket structure. A recent study by Buende et al. predict that a failure is most likely to occur in a weld. The study is based on data from other large structures, particularly nuclear reactors. The data used also appear to be consistent with the operating experience of the Fast Flux Test Facility (FFTF). This reactor has a fuel pin area comparable with the area of the ITER first wall and has experienced one unanticipated fuel pin failure after two years of operation. The repair of irradiated structures using fusion welding will be difficult due to the entrapped helium. Due to its extremely low solubility in metals, helium will diffuse and agglomerate to form helium bubbles after being trapped at point defects, dislocations, and grain boundaries. Welding of neutron-irradiated type 304 stainless steels has been reported with varying degree of heat-affected zone cracking (HAZ). The objectives of this study were to determine the threshold helium concentrations required to cause HAZ cracking and to investigate techniques that might be used to eliminate the HAZ cracking in welding of helium-containing materials

Investigation on microstructure and properties of narrow-gap laser welding on reduced activation ferritic/martensitic steel CLF-1 with a thickness of 35 mm

Science.gov (United States)

Wu, Shikai; Zhang, Jianchao; Yang, Jiaoxi; Lu, Junxia; Liao, Hongbin; Wang, Xiaoyu

2018-05-01

Reduced activation ferritic martensitic (RAFM) steel is chosen as a structural material for test blanket modules (TBMs) to be constructed in International Thermonuclear Experimental Reactor (ITER) and China Fusion Engineering Test Reactor (CFETR). Chinese specific RAFM steel named with CLF-1 has been developed for CFETR. In this paper, a narrow-gap groove laser multi-pass welding of CLF-1 steel with thickness of 35 mm is conduced by YLS-15000 fiber laser. Further, the microstructures of different regions in the weld joint were characterized, and tensile impact and micro-hardness tests were carried out for evaluating the mecharical properties. The results show that the butt weld joint of CLF-1 steel with a thickness of 35 mm was well-formed using the optimal narrow-gap laser filler wire welding and no obvious defects was found such as incomplete fusion cracks and pores. The microstructures of backing layer is dominated by lath martensites and the Heat-Affected Zone (HAZ) was mainly filled with two-phase hybrid structures of secondary-tempering sorbites and martensites. The filler layer is similar to the backing layer in microstructures. In tensile tests, the tensile samples from different parts of the joint all fractured at base metal (BM). The micro-hardness of weld metal (WM) was found to be higher than that of BM and the Heat-Affected Zone (HAZ) exhibited no obvious softening. After post weld heat treatment (PWHT), it can be observed that the fusion zone of the autogenous welding bead and the upper filling beads mainly consist of lath martensites which caused the lower impact absorbing energy. The HAZ mainly included two-phase hybrid structures of secondary-tempering sorbites and martensites and exhibited favorable impact toughness.

Dos décadas de seguimiento exitoso de la primera ablación de arritmias por catéter de radiofrecuencia realizado en la historia de la medicina del Paraguay

Directory of Open Access Journals (Sweden)

Osmar Antonio Centurión

2015-08-01

Full Text Available La técnica de mapeo endocárdico durante el estudio electrofisiológico ha sido extensamente empleada en el análisis de las taquicardias paroxísticas supraventriculares (TPS. Mediante este mapeo endocárdico y el análisis meticuloso de los electrogramas endocárdicos y los respectivos intervalos de conducción, es posible localizar el sitio de origen de las arritmias y así facilitar su tratamiento ablativo por medio de catéteres de radiofrecuencia. Se describe el caso de un hombre de 29 años con síndrome de Wolff-Parkinson-White (WPW que manifiestó que presentaba varios episodios documentados de TPS con serio compromiso hemodinámico que motivaba su frecuente internación en terapia intensiva. El mapeo electrofisiológico endocárdico meticuloso demostró la presencia de un haz anómalo de Kent auriculoventricular izquierdo en posición posteroseptal. El período refractario absoluto del haz anómalo de Kent fue de 240 ms. La primera emisión de radiofrecuencia a través de un catéter adecuadamente posicionado previo terminó la taquicardia. La taquicardia permaneció no inducible a partir de entonces. En estas dos décadas de seguimiento clínico, el paciente no ha presentado ni un solo episodio de taquicardia. La curación definitiva generada por la ablación del haz anómalo de Kent ha proporcionado un cambio drástico, total y beneficioso en la calidad de vida al paciente. Los beneficios clínicos y socioeconómicos son mayores cuanto más temprano en la evolución se realice el procedimiento de ablación de arritmias.

Development and evaluation of SUS 304H — IN 617 welds for advanced ultra supercritical boiler applications

International Nuclear Information System (INIS)

Pavan, A.H.V.; Vikrant, K.S.N.; Ravibharath, R.; Singh, Kulvir

2015-01-01

At moderately high temperature sections of Advanced Ultra Super Critical (AUSC) boilers, welding of superalloys to austenitic steels is inevitable owing to economic aspects of boiler. Welding of SUS 304H and Inconel 617 (IN 617) was attempted using IN 617 filler material employing conventional Gas Tungsten Arc Welding (GTAW) process and the procedure was successfully established along with optimized welding parameters. Microstructural characterization was carried out to identify various zones on either side of the fusion boundaries. Unmixed Zone and Heat Affected Zone (HAZ) were observed towards SUS 304H fusion boundary while no distinct HAZ was observed towards IN 617 fusion boundary. Micro-hardness profiling indicated decrease in hardness at the HAZ towards SUS 304H fusion boundary. Mechanical properties evaluation at both ambient and elevated temperatures was carried out and data obtained was compared with those of base metals. The tensile strength of the cross weld specimens at high temperatures were observed to be marginally lower than that of IN 617 but significantly more than that of SUS 304H, hence, tolerable. Stress-rupture properties of the cross-weld specimens as tested in this study were found to be intermediate to the base metals’ data, thus, suitable for AUSC power plants' boiler applications. Hence, this work gives an insight into welding procedure establishment, microstructural development, variation of mechanical properties at elevated temperatures and stress-rupture properties of the dissimilar metal welds at elevated temperatures. - Highlights: • Procedure establishment & parameters optimization for fabricating defect-free welds. • Characterization of various zones formed during welding. • Mechanical properties evaluation and comparison with those of base metals. • Influence of various zones formed during welding on mechanical properties inferred. • Understanding long term behavior of welds at elevated temperatures

Effect of welding thermal cycles on the structure and properties of simulated heat-affected zone areas in X10CrMoVNb9-1 (T91) steel at a state after 100,000 h of operation

Energy Technology Data Exchange (ETDEWEB)

Łomozik, Mirosław, E-mail: miroslaw.lomozik@is.gliwice.pl [Instytut Spawalnictwa, Testing of Materials Weldability and Welded Constructions Department, 44-100 Gliwice, Bł. Czesława 16-18 (Poland); Hernas, Adam, E-mail: adam.hernas@polsl.pl [Silesian University of Technology, Faculty of Materials Engineering and Metallurgy, 40-019 Katowice, Krasińskiego 8 str. (Poland); Zeman, Marian L., E-mail: marian.zeman@is.gliwice.pl [Instytut Spawalnictwa, Testing of Materials Weldability and Welded Constructions Department, 44-100 Gliwice, Bł. Czesława 16-18 (Poland)

2015-06-18

The article presents results of structural tests (light, scanning electron and scanning transmission electron microscopy) of X10CrMoVNb9-1 (T91) creep-resisting steel after approximately 100,000 h of operation. It was ascertained that the parent metal of T91 steel is characterized by the microstructure of tempered martensite with M{sub 23}C{sub 6} carbide precipitates and few dispersive precipitates of MX-type niobium and vanadium carbonitrides. The most inconvenient change in T91 steel precipitate morphology due to long-term operation is the appearance of the Laves Fe{sub 2}Mo phase which along with M{sub 23}C{sub 6} carbide particles forms elongated blocks and conglomerates on grain boundaries. The article also presents results of tests related to the effect of simulated welding thermal cycles on selected properties of X10CrMoVNb9-1 (T91) grade steel at a state after approximately 100,000 h of operation. The tests involved the determination of the chemical composition of the steel tested as well as impact tests, hardness measurements and microscopic metallographic examination (based on light microscopy) of simulated heat-affected zone (HAZ) areas for a cooling time (t{sub 8/5}) restricted within a range between 3 s and 120 s, with and without heat treatment. The tests revealed that, among other results, hardness values of simulated HAZ areas in X10CrMoVNb9-1 (T91) steel do not guarantee cold crack safety of the steel at the state without additional heat treatment. It was also observed that simulated welding thermal cycles of cooling times t{sub 8/5}=3, 12, 60 and 120 s do not significantly affect the toughness and hardness of simulated HAZ areas of the steel tested.

Development and evaluation of SUS 304H — IN 617 welds for advanced ultra supercritical boiler applications

Energy Technology Data Exchange (ETDEWEB)

Pavan, A.H.V., E-mail: pavanahv@bhelrnd.co.in [Metallurgy Department, Corporate R& D Division, Bharat Heavy Electricals Limited, Vikasnagar, Hyderabad 500 093 (India); Vikrant, K.S.N., E-mail: vikrant@bhelrnd.co.in [Metallurgy Department, Corporate R& D Division, Bharat Heavy Electricals Limited, Vikasnagar, Hyderabad 500 093 (India); Ravibharath, R., E-mail: rrbharath@bhelrnd.co.in [Welding Research Institute, Bharat Heavy Electricals Limited, Tiruchirapalli 620 014 (India); Singh, Kulvir, E-mail: kulvir@bhelrnd.co.in [Metallurgy Department, Corporate R& D Division, Bharat Heavy Electricals Limited, Vikasnagar, Hyderabad 500 093 (India)

2015-08-26

At moderately high temperature sections of Advanced Ultra Super Critical (AUSC) boilers, welding of superalloys to austenitic steels is inevitable owing to economic aspects of boiler. Welding of SUS 304H and Inconel 617 (IN 617) was attempted using IN 617 filler material employing conventional Gas Tungsten Arc Welding (GTAW) process and the procedure was successfully established along with optimized welding parameters. Microstructural characterization was carried out to identify various zones on either side of the fusion boundaries. Unmixed Zone and Heat Affected Zone (HAZ) were observed towards SUS 304H fusion boundary while no distinct HAZ was observed towards IN 617 fusion boundary. Micro-hardness profiling indicated decrease in hardness at the HAZ towards SUS 304H fusion boundary. Mechanical properties evaluation at both ambient and elevated temperatures was carried out and data obtained was compared with those of base metals. The tensile strength of the cross weld specimens at high temperatures were observed to be marginally lower than that of IN 617 but significantly more than that of SUS 304H, hence, tolerable. Stress-rupture properties of the cross-weld specimens as tested in this study were found to be intermediate to the base metals’ data, thus, suitable for AUSC power plants' boiler applications. Hence, this work gives an insight into welding procedure establishment, microstructural development, variation of mechanical properties at elevated temperatures and stress-rupture properties of the dissimilar metal welds at elevated temperatures. - Highlights: • Procedure establishment & parameters optimization for fabricating defect-free welds. • Characterization of various zones formed during welding. • Mechanical properties evaluation and comparison with those of base metals. • Influence of various zones formed during welding on mechanical properties inferred. • Understanding long term behavior of welds at elevated temperatures.

Postinfancy growth, schooling, and cognitive achievement: Young Lives.

Science.gov (United States)

Crookston, Benjamin T; Schott, Whitney; Cueto, Santiago; Dearden, Kirk A; Engle, Patrice; Georgiadis, Andreas; Lundeen, Elizabeth A; Penny, Mary E; Stein, Aryeh D; Behrman, Jere R

2013-12-01

Early life growth failure and resulting cognitive deficits are often assumed to be very difficult to reverse after infancy. We used data from Young Lives, which is an observational cohort of 8062 children in Ethiopia, India, Peru, and Vietnam, to determine whether changes in growth after infancy are associated with schooling and cognitive achievement at age 8 y. We represented the growth by height-for-age z score at 1 y [HAZ(1)] and height-for-age z score at 8 y that was not predicted by the HAZ(1). We also characterized growth as recovered (stunted at age 1 y and not at age 8 y), faltered (not stunted at age 1 y and stunted at age 8 y), persistently stunted (stunted at ages 1 and 8 y), or never stunted (not stunted at ages 1 and 8 y). Outcome measures were assessed at age 8 y. The HAZ(1) was inversely associated with overage for grade and positively associated with mathematics achievement, reading comprehension, and receptive vocabulary. Unpredicted growth from 1 to 8 y of age was also inversely associated with overage for grade (OR range across countries: 0.80-0.84) and positively associated with mathematics achievement (effect-size range: 0.05-0.10), reading comprehension (0.02-0.10), and receptive vocabulary (0.04-0.08). Children who recovered in linear growth had better outcomes than did children who were persistently stunted but were not generally different from children who experienced growth faltering. Improvements in child growth after early faltering might have significant benefits on schooling and cognitive achievement. Hence, although early interventions remain critical, interventions to improve the nutrition of preprimary and early primary school-age children also merit consideration.

Effect of low-dose versus higher-dose antenatal iron supplementation on child health outcomes at 36 months of age in Viet Nam: longitudinal follow-up of a cluster randomised controlled trial.

Science.gov (United States)

Hanieh, Sarah; Ha, Tran T; Simpson, Julie A; Braat, Sabine; Thuy, Tran T; Tran, Thach D; King, Janet; Tuan, Tran; Fisher, Jane; Biggs, Beverley-Ann

2017-01-01

Intermittent iron-folic acid supplementation (IFA) is currently recommended for pregnant women in populations where anaemia prevalence among pregnant women is Viet Nam among children of 36 months of age, born to women previously enrolled in a cluster randomised controlled trial of antenatal micronutrient supplementation (daily IFA (60 mg elemental iron) vs twice-weekly IFA (60 mg elemental iron) vs twice-weekly multiple micronutrient (MMN) supplementation (60 mg elemental iron)). Primary outcomes were height-for-age z-scores (HAZ), according to WHO growth standards and cognitive composite scores (Bayley Scales of Infant and Toddler Development, third edition) at 36 months of age. A total of 1017 children born to mothers enrolled in the cluster randomised trial were assessed at 36 months of age. Adjusted mean differences (MDs) in HAZ were -0.14 (95% CI -0.28 to -0.01) and -0.15 (95% CI -0.29 to -0.01) in children born to mothers who received twice-weekly IFA or MMN compared with those who received daily IFA. Children born to mothers who received twice-weekly MMN had lower composite motor scores compared with those who received daily IFA (MD -2.07, 95% CI -4.11 to -0.03). There were no differences in composite cognitive scores in the twice-weekly compared with daily regimens. Low-dose antenatal IFA supplementation (120 mg elemental iron per week) resulted in lower HAZ and motor composite scores in children compared with higher-dose antenatal IFA supplementation (420 mg elemental iron per week). This highlights the importance of adequate iron stores during pregnancy and the need for careful monitoring when lower-dose antenatal iron regimens are used. Australia New Zealand Clinical Trials Registry: 12610000944033.

Heat-affected zone liquation crack on resistance spot welded TWIP steels

Energy Technology Data Exchange (ETDEWEB)

Saha, Dulal Chandra [Department of Advanced Materials Engineering, Dong-Eui University, 995 Eomgwangno, Busanjin-gu, Busan 614-714 (Korea, Republic of); Chang, InSung [Automotive Production Development Division, Hyundai Motor Company (Korea, Republic of); Park, Yeong-Do, E-mail: ypark@deu.ac.kr [Department of Advanced Materials Engineering, Dong-Eui University, 995 Eomgwangno, Busanjin-gu, Busan 614-714 (Korea, Republic of)

2014-07-01

In this study, the heat affected zone (HAZ) liquation crack and segregation behavior of the resistance spot welded twinning induced plasticity (TWIP) steel have been reported. Cracks appeared in the post-welded joints that originated at the partially melted zone (PMZ) and propagated from the PMZ through the heat affected zone (HAZ) to the base metal (BM). The crack length and crack opening widths were observed increasing with heat input; and the welding current was identified to be the most influencing parameter for crack formation. Cracks appeared at the PMZ when nugget diameter reached at 4.50 mm or above; and the liquation cracks were found to occur along two sides of the notch tip in the sheet direction rather than in the electrode direction. Cracks were backfilled with the liquid films which has lamellar structure and supposed to be the eutectic constituent. Co-segregation of alloy elements such as, C and Mn were detected on the liquid films by electron-probe microanalysis (EPMA) line scanning and element map which suggests that the liquid film was enrich of Mn and C. The eutectic constituent was identified by analyzing the calculated phase diagram along with thermal temperature history of finite element simulation. Preliminary experimental results showed that cracks have less/no significant effect on the static cross-tensile strength (CTS) and the tensile-shear strength (TSS). In addition, possible ways to avoid cracking were discussed. - Highlights: • The HAZ liquation crack during resistance spot welding of TWIP steel was examined. • Cracks were completely backfilled and healed with divorced eutectic secondary phase. • Co-segregation of C and Mn was detected in the cracked zone. • Heat input was the most influencing factor to initiate liquation crack. • Cracks have less/no significant effect on static tensile properties.

Heat-affected zone liquation crack on resistance spot welded TWIP steels

International Nuclear Information System (INIS)

Saha, Dulal Chandra; Chang, InSung; Park, Yeong-Do

2014-01-01

In this study, the heat affected zone (HAZ) liquation crack and segregation behavior of the resistance spot welded twinning induced plasticity (TWIP) steel have been reported. Cracks appeared in the post-welded joints that originated at the partially melted zone (PMZ) and propagated from the PMZ through the heat affected zone (HAZ) to the base metal (BM). The crack length and crack opening widths were observed increasing with heat input; and the welding current was identified to be the most influencing parameter for crack formation. Cracks appeared at the PMZ when nugget diameter reached at 4.50 mm or above; and the liquation cracks were found to occur along two sides of the notch tip in the sheet direction rather than in the electrode direction. Cracks were backfilled with the liquid films which has lamellar structure and supposed to be the eutectic constituent. Co-segregation of alloy elements such as, C and Mn were detected on the liquid films by electron-probe microanalysis (EPMA) line scanning and element map which suggests that the liquid film was enrich of Mn and C. The eutectic constituent was identified by analyzing the calculated phase diagram along with thermal temperature history of finite element simulation. Preliminary experimental results showed that cracks have less/no significant effect on the static cross-tensile strength (CTS) and the tensile-shear strength (TSS). In addition, possible ways to avoid cracking were discussed. - Highlights: • The HAZ liquation crack during resistance spot welding of TWIP steel was examined. • Cracks were completely backfilled and healed with divorced eutectic secondary phase. • Co-segregation of C and Mn was detected in the cracked zone. • Heat input was the most influencing factor to initiate liquation crack. • Cracks have less/no significant effect on static tensile properties

Thermal Aging Effects on Heat Affected Zone of Alloy 600 in Dissimilar Metal Weld

Energy Technology Data Exchange (ETDEWEB)

Ham, Jun Hyuk; Choi, Kyoung Joon; Yoo, Seung Chang; Kim, Ji Hyun [UNIST, Ulsan (Korea, Republic of)

2016-05-15

Dissimilar metal weld (DMW), consists of Alloy 600, Alloy 182, and A508 Gr.3, is now being widely used as the reactor pressure vessel penetration nozzle and the steam generator tubing material for pressurized water reactors (PWR) because of its mechanical property, thermal expansion coefficient, and corrosion resistance. The heat affected zone (HAZ) on Alloy 600 which is formed by welding process is critical to crack. According to G.A. Young et al. crack growth rates (CGR) in the Alloy 600 HAZ were about 30 times faster than those in the Alloy 600 base metal tested under the same conditions [3]. And according to Z.P. Lu et al. CGR in the Alloy 600 HAZ can be more than 20 times higher than that in its base metal. To predict the life time of components, there is a model which can calculate the effective degradation years (EDYs) of the material as a function of operating temperature. This study was conducted to investigate how thermal aging affects the hardness of dissimilar metal weld from the fusion boundary to Alloy 600 base metal and the residual strain at Alloy 600 heat affected zone. Following conclusions can be drawn from this study. The hardness, measured by Vickers hardness tester, peaked near the fusion boundary between Alloy 182 and Alloy 600, and it decreases as the picked point goes to Alloy 600 base metal. Even though the formation of precipitate such as Cr carbide, thermal aging doesn't affect the value and the tendency of hardness because of reduced residual stress. According to kernel average misorientation mapping, residual strain decreases when the material thermally aged. And finally, in 30 years simulated specimen, the high residual strain almost disappears. Therefore, the influence of residual strain on primary water stress corrosion cracking can be diminished when the material undergoes thermal aging.

Efeito da energia de soldagem sobre a microestrutura e propriedades mecânicas da zona afetada pelo calor de juntas de aço inoxidável duplex Effect of the welding heat input on the microstructure and mechanical properties of the heat affected zone of multipass welded joints of duplex stainless steel

Directory of Open Access Journals (Sweden)

Everton Barbosa Nunes

2011-09-01

Full Text Available O objetivo deste trabalho é analisar a influência da energia de soldagem na zona afetada pelo calor (ZAC, de juntas soldadas do aço inoxidável duplex UNS S31803. Foram realizadas soldagens com eletrodo revestido AWS E2209-17 em junta tipo V de Aço Inoxidável Duplex UNS S31803, com dois níveis de energia (15 e 20 kJ/cm. A condição soldada com energia mais elevada apresentou uma ZAC mais extensa e microestrutura mais grosseira nos passes de acabamento. No entanto, nos passes de enchimento e de raiz, as ZAC's destas regiões foram mais refinadas e menos extensa. Em relação à microdureza, a condição soldada com energia de 15 kJ/cm apresentou níveis menores. Em relação à tenacidade, não foi verificada diferença significativa nos resultados.The aim this work is to evaluate the influence of multipass welding heat input on the microstructure and mechanical properties of the heat affected zone (HAZ of UNS S31803 duplex stainless steel multipass welded joints. The shielded metal arc welding process using as filler metal the AWS E2209-17 covered electrode were employed had been carried through V joint groove UNS S31803 DSS, so that two levels of energy (15 and 20 kJ/cm had been used in this experiment. The condition welded with higher energy higher a HAZ extensive and coarser microstructure in the finishing passes. On the other hand, in the wadding passes and root pass, the HAZ this region was more refined and less extensive. In respect of microhardness, the condition welded with energy of 15 kJ/cm got lower levels. In relation to toughness, it was not observed significant differences.

Femtosecond versus nanosecond laser machining: comparison of induced stresses and structural changes in silicon wafers

International Nuclear Information System (INIS)

Amer, M.S.; El-Ashry, M.A.; Dosser, L.R.; Hix, K.E.; Maguire, J.F.; Irwin, Bryan

2005-01-01

Laser micromachining has proven to be a very successful tool for precision machining and microfabrication with applications in microelectronics, MEMS, medical device, aerospace, biomedical, and defense applications. Femtosecond (FS) laser micromachining is usually thought to be of minimal heat-affected zone (HAZ) local to the micromachined feature. The assumption of reduced HAZ is attributed to the absence of direct coupling of the laser energy into the thermal modes of the material during irradiation. However, a substantial HAZ is thought to exist when machining with lasers having pulse durations in the nanosecond (NS) regime. In this paper, we compare the results of micromachining a single crystal silicon wafer using a 150-femtosecond and a 30-nanosecond lasers. Induced stress and amorphization of the silicon single crystal were monitored using micro-Raman spectroscopy as a function of the fluence and pulse duration of the incident laser. The onset of average induced stress occurs at lower fluence when machining with the femtosecond pulse laser. Induced stresses were found to maximize at fluence of 44 J cm -2 and 8 J cm -2 for nanosecond and femtosecond pulsed lasers, respectively. In both laser pulse regimes, a maximum induced stress is observed at which point the induced stress begins to decrease as the fluence is increased. The maximum induced stress was comparable at 2.0 GPa and 1.5 GPa for the two lasers. For the nanosecond pulse laser, the induced amorphization reached a plateau of approximately 20% for fluence exceeding 22 J cm -2 . For the femtosecond pulse laser, however, induced amorphization was approximately 17% independent of the laser fluence within the experimental range. These two values can be considered nominally the same within experimental error. For femtosecond laser machining, some effect of the laser polarization on the amount of induced stress and amorphization was also observed

Bulletin of Materials Science | News

Indian Academy of Sciences (India)

On the morphology of SrCO3 crystals grown at the interface between two immiscible liquids ... of weld heat input on toughness and structure of HAZ of a new super-high strength steel .... pp 343-348 Thin Films. Optimization of pH and direct imaging conditions of complexed methylene blue sensitized poly(vinyl chloride) films.

Defense AT&L (Volume 36, Number 2, March-April 2007)

Science.gov (United States)

2007-04-01

early what we are going to do with haz- ardous materials, scrap metal, and items that can’t be re- turned to the United States, such as canvas tentage...Center in Arlington, Va. For ex- ample, the new CAC contains two fingerprints and a dig- ital photograph, she noted. Additionally, “we’re going to

30 CFR 47.41 - Requirement for container labels.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Requirement for container labels. 47.41 Section... TRAINING HAZARD COMMUNICATION (HazCom) Container Labels and Other Forms of Warning § 47.41 Requirement for container labels. (a) The operator must ensure that each container of a hazardous chemical has a label. If a...

Modeling of hydrogen induced cold cracking in a ferritic steel

International Nuclear Information System (INIS)

Chen, Qianqiang

2015-01-01

This thesis is aimed at studying the hydrogen induced cold cracking (HICC) in the heated affected zone (HAZ) of weldments and at proposing a criterion to predict this phenomenon. HICC is attributable to three factors: i) a susceptible microstructure; ii) hydrogen concentration; and iii) a critical stress. To this end, first tensile tests on smooth specimens charged with hydrogen were performed to investigate hydrogen embrittlement of martensite. According to these results, a ductile-brittle damage model is proposed in order to establish a HICC criterion. In order to validate this criterion, we performed the modified Tekken tests. The Tekken test was chosen because one can control the welding parameters in order to induce cold cracking. The modified Tekken tests have then been modeled using a fully coupled thermo-metallo-mechanical-diffusion model using the finite element method. This model allows to compute martensite's portion, residual stress level and hydrogen concentration in the HAZ. By applying the HICC criterion to these tests, cold cracking phenomenon has been correctly predicted. (author)

Effect of inter-critically reheating temperature on microstructure and properties of simulated inter-critically reheated coarse grained heat affected zone in X70 steel

International Nuclear Information System (INIS)

Zhu, Zhixiong; Kuzmikova, Lenka; Li, Huijun; Barbaro, Frank

2014-01-01

This study investigated the influence of the inter-critical reheating temperature on the microstructure and mechanical properties of a coarse grained heat affected zone (CGHAZ) in an API 5L grade X70 pipeline steel seam weld. A Gleeble 3500 thermo-mechanical simulator was employed to duplicate particular weld thermal cycles in order to accurately assess specific regions of the weld HAZ. Detailed microstructural analysis, including investigation of the martensite–austenite (M–A) constituent, was performed using optical microscope (OM), scanning electron microscope (SEM) and selective etching techniques. It is shown that the fracture toughness of the CGHAZ is significantly reduced following exposure to a subsequent inter-critical thermal cycle. Fracture toughness gradually improves as the inter-critical temperature is increased, but does not return to the value of the original CGHAZ due to the presence of isolated large M–A particles and coarse microstructure. Significance of M–A particles to the HAZ fracture toughness is first related to the location of particles along prior austenite grain boundaries, followed by the size of individual M–A particles

Microstructural Study of 17-4PH Stainless Steel after Plasma-Transferred Arc Welding

Directory of Open Access Journals (Sweden)

Dewei Deng

2015-01-01

Full Text Available The improvement of the surface qualities and surface hardening of precipitation hardened martensitic stainless steel 17-4PH was achieved by the plasma-transferred arc welding (PTAW process deposited with Co-based alloy. The microstructure of the heat affected zone (HAZ and base metal were characterized by optical microscope (OM, scanning electron microscope (SEM and transmission electron microscope (TEM. The results show that there are obvious microstructural differences between the base metal and HAZ. For example, base material is transformed from lath martensite to austenite due to the heateffect of the welding process. On the other hand, the precipitate in the matrix (bar-like shape Cr7C3 phase with a width of about one hundred nanometres and a length of hundreds of nanometres grows to a rectangular appearance with a width of about two hundred nanometres and a length of about one micron. Stacking fault could also be observed in the Cr7C3 after PTAW. The above means that welding can obviously improve the surface qualities.

Prevention of weld-decay in austenitic stainless steel by using surface mechanical attrition treatment

Science.gov (United States)

Laleh, Majid; Kargar, Farzad; Rouhaghdam, Alireza Sabour

2012-11-01

Surface mechanical attrition treatment (SMAT) was applied to the samples of a type AISI 304 stainless steel in order to induce grain refinement as well as formation of twins. Transmission electron microscopy and X-ray diffraction analysis results showed that the average grain size at the surface of the SMATed sample was about 10 nm. The untreated and SMATed samples were then welded using a one-pass gas tungsten arc procedure. The heat-affected zone (HAZ) of the samples was examined by optical microscopy and corrosion tests. Results of the double loop electrochemical potentiokinetic reactivation tests showed that the degree of sensitization in the HAZ for the SMATed sample was very low as compared to that of the untreated one. The pre-SMATed sample was resistant to intergranular corrosion. This is mainly due to the formation of high density of twins which are not prone to carbide precipitation because of their regular and coherent atomic structure and extreme low grain boundary energy as compared with those of other grain boundaries.

Phase transformation and mechanical behavior in annealed 2205 duplex stainless steel welds

International Nuclear Information System (INIS)

Badji, Riad; Bouabdallah, Mabrouk; Bacroix, Brigitte; Kahloun, Charlie; Belkessa, Brahim; Maza, Halim

2008-01-01

The phase transformations and mechanical behaviour during welding and subsequent annealing treatment of 2205 duplex stainless steel have been investigated. Detailed microstructural examination showed the presence of higher ferrite amounts in the heat affected zone (HAZ), while higher amounts of austenite were recorded in the centre region of the weld metal. Annealing treatments in the temperature range of 800-1000 deg. C resulted in a precipitation of σ phase and M 23 C 6 chromium carbides at the γ/δ interfaces that were found to be preferential precipitation sites. Above 1050 deg. C, the volume fraction of δ ferrite increases with annealing temperature. The increase of δ ferrite occurs at a faster rate in the HAZ than in the base metal and fusion zone. Optimal mechanical properties and an acceptable ferrite/austenite ratio throughout the weld regions corresponds to annealing at 1050 deg. C. Fractographic examinations showed that the mode of failure changed from quasi-cleavage fracture to dimple rupture with an increase in the annealing temperature from 850 to 1050 deg. C

Microstructural Characterization of Thermomechanical and Heat-Affected Zones of an Inertia Friction Welded Astroloy

Science.gov (United States)

Oluwasegun, K. M.; Olawale, J. O.; Ige, O. O.; Shittu, M. D.; Adeleke, A. A.; Malomo, B. O.

2014-08-01

The behaviour of γ' phase to thermal and mechanical effects during rapid heating of Astroloy, a powder metallurgy nickel-based superalloy has been investigated. The thermo-mechanical-affected zone (TMAZ) and heat-affected zone (HAZ) microstructures of an inertia friction welded (IFW) Astroloy were simulated using a Gleeble thermo-mechanical simulation system. Detailed microstructural examination of the simulated TMAZ and HAZ and those present in actual IFW specimens showed that γ' particles persisted during rapid heating up to a temperature where the formation of liquid is thermodynamically favored and subsequently re-solidified eutectically. The result obtained showed that forging during the thermo-mechanical simulation significantly enhanced resistance to weld liquation cracking of the alloy. This is attributable to strain-induced rapid isothermal dissolution of the constitutional liquation products within 150 μm from the center of the forged sample. This was not observed in purely thermally simulated samples. The microstructure within the TMAZ of the as-welded alloy is similar to the microstructure in the forged Gleeble specimens.

Microstructural and Mechanical Properties of Welded High Strength Steel Plate Using SMAW and SAW Method for LPG Storage Tanks

Science.gov (United States)

Winarto, Winarto; Riastuti, Rini; Kumeidi, Nur

2018-03-01

Indonesian government policy to convert energy consumption for domestic household from kerosene to liquefied petroleum gas (LPG) may lead to the increasing demand for LPG storage tank. LPG storage tank with a large capacity generally used the HSLA steel material of ASTM A516 Grade 70 joined by SMAW or combination between SMAW and SAW method. The heat input can affect the microstructure and mechanical properties of the weld area. The input heat is proportional to the welding current and the arc voltage, but inversely proportional to its welding speed. The result shows that the combination of SMAW-SAW process yield the lower hardness in the HAZ and the fusion zone compared to the singe SMAW process. PWHT mainly applied to reduce residual stress of welded joint. The result shows that PWHT can reduce the hardness in the HAZ and the fusion zone in comparing with the singe SMAW process. The microstructure of weld joint shows a coarser structure in the combined welding process (SMAW-SAW) comparing with the single welding process (SMAW).

Material pre-conditioning effects on the creep behaviour of 316H stainless steel

International Nuclear Information System (INIS)

Mehmanparast, A.; Davies, C.M.; Dean, D.W.; Nikbin, K.

2013-01-01

Material pre-conditioning by, for example, pre-strain through component bending and welding is known to alter the creep deformation and creep crack growth (CCG) behaviour of 316H stainless steel. Experimental test data on the creep deformation and crack growth behaviour of 316H weldment compact tension specimens at 550 °C, where the starter defect was introduced into the heat affected zone (HAZ), have been compared to those of obtained from similar specimens manufactured from parent material, which had been subjected to 8% compressive plastic pre-strain at room temperature. Similar degrees of accelerated cracking behaviour compared to parent material, for given values of C*, were exhibited in both 316H HAZ and pre-compressed parent materials. This acceleration has been attributed to the influence of material hardening effects and the reduction of creep ductility in the pre-conditioned materials. These results are discussed in terms of the potential for using material pre-conditioning to assist in predicting the long term cracking behaviour of high temperature 316H stainless steel plant components from shorter term laboratory CCG tests

Reactor pressure boundary material; the modeling for the prediction of the welding characteristics of SA508-cl.3 pressure vessel steel welds

Energy Technology Data Exchange (ETDEWEB)

Lee, Chang Hee; Uhm, Sang Ho; Seo, Young Dae; Moon, Younk Ju; Kim, Bum Joo; Shim, Min Hyo [Hanyang University, Seoul (Korea)

2002-03-01

A metallurgical model for predicting the welding characteristics such as final microstructure and mechanical properties of HAZ was established and various kinetic parameters which was necessary to the model were measured and formulated through isothermal grain growth and isothermal transformation experiments. This model consisted of two sub-models; Grain growth model and Transformation model. Grain growth model was developed to calculate the thermal cycle from heat input and the change of austenite grain size which occurred during heating cycle. Transformation model described the phase transition behavior and predicted the final mechanical properties determined by structure-property relationships. The isothermal kinetics of grain growth and dissolution of precipitates were respectively described by well-known equation, dD/dt = M( {delta}F{sub e}ff ){sup m} and Whelan's analytical model. Isothermal transformation kinetics was expressed by Avrami equation. The reliabilities of each model were evaluated by HAZ microstructural simulation tests. It was found the both models were in good agreement. The applicability of this model was discussed by illustrating the results of the model. 129 refs., 81 figs., 11 tabs. (Author)

Study of sulphate-reducing bacteria corrosion in the weld joint for API X-70 steel

Energy Technology Data Exchange (ETDEWEB)

Flores, J. E.; Patino-Carachure, C.; Alfonso, I.; Rodriguez, J. A.; Rosas, G.

2012-11-01

The corrosion behavior originated by sulfate-reducing bacteria (SRB) was studied in two regions of welded API X-70 steel pipeline. The studies were focused on base material (BM) and heat affected zone (HAZ), from the internal region of the pipe. SRB were extracted from oil and grown in a Postgate medium. Corrosion was evaluated at 60 degree centigrade for times between 5 and 64 days. Potentiodynamic polarization curves, obtained by electrochemical techniques, indicated surface activation at short times. Structural and morphological characterizations were carried out by scanning electron microscopy (SEM) and optical microscopy (OM). H{sub 2}S concentration and pH were also measured. Results showed an important increase in the corrosion damage up to 20 days, influenced by the SRB activity, which lead to a maximum of H{sub 2}S (pH minimum). It was found a localized corrosion attack in the HAZ in a higher quantity compared to BM; and the formation of a thin film on the steel surface, originated by corrosion products and bacterial activity. (Author) 15 refs.

The Influence of the Heat-Affected Zone Mechanical Properties on the Behaviour of the Welding in Transverse Plate-to-Tube Joints.

Science.gov (United States)

Lozano, Miguel; Serrano, Miguel A; López-Colina, Carlos; Gayarre, Fernando L; Suárez, Jesús

2018-02-09

Eurocode 3 establishes the component method to analytically characterize the structural joints between beam and columns. When one of the members involved in the joint is a hollow section (i.e., a tube) there is a lack of information for the specific components present in the joint. There are two different ways to bridge the gap: experimental testing on the actual beam column joints involving tubular sections; or numerical modelization, typically by means of finite element analysis. For this second option, it is necessary to know the actual mechanical properties of the material. As long as the joint implies a welding process, there is a concern related to how the mechanical properties in the heat-affected zone (HAZ) influence the behavior of the joint. In this work, some coupons were extracted from the HAZ of the beam-column joint. The coupons were tested and the results were implemented in the numerical model of the joint, in an attempt to bring it closer to the experimental results of the tested joints.

Recommendations for J and CTOD testing of strength mismatched. GKSS and EDF view

Energy Technology Data Exchange (ETDEWEB)

Kocak, M.; Kim, Y.J.; Hornet, P

1998-03-01

Recommendations for toughness testing and evaluation procedures for weldments are given in this paper. For testing aspects, two testing methods are outlined, micro-flat tensile tests and the {delta}{sub 5} testing technique. The micro-flat tensile tests are extremely useful to measure tensile properties for the Heat Affected Zone (HAZ) of multipass welds and very thin weld regions such as laser beam or electron beam and it is rather universal. It can be applied to any type of test pieces as well as to structural components with surface breaking cracks. These two test methods can provide efficient tools for tensile and fracture testing of metallic materials joined by fusion welding technology including high power beam welding processes. For toughness evaluation aspects, the J estimation procedures for mismatched specimens are reviewed, including a summary of a new proposal for best estimates of the mismatch on the J integral. The new procedure covers not only weld metal cracks but also HAZ cracks. Finally some recommendations are given for further development. (author) 29 refs.

Evaluation of AISI 4140 Steel Repair Without Post-Weld Heat Treatment

Science.gov (United States)

Silva, Cleiton C.; de Albuquerque, Victor H. C.; Moura, Cícero R. O.; Aguiar, Willys M.; Farias, Jesualdo P.

2009-04-01

The present work evaluates the two-layer technique on the heat affected zone (HAZ) of AISI 4140 steel welded with different heat input levels between the first and second layer. The weld heat input levels selected by the Higuchi test were 5/5, 5/10, and 15/5 kJ/cm. The evaluation of the refining and/or tempering of the coarsened grain HAZ of the first layer was carried out using metallographic tests, microhardness measurements, and the Charpy-V impact test. The tempering of the first layer was only reached when the weld heat input ratio was 5/5 kJ/cm. The results of the Charpy-V impact test showed that the two-layer technique was efficient, from the point of view of toughness, since the toughness values reached were greater than the base metal for all weld heat input ratios applied. The results obtained indicate that the best performance of the two-layer deposition technique was for the weld heat input ratio 5/5 kJ/cm employing low heat input.

Parametric Study On The CW Nd: YAG Laser Cutting Quality Of 1.25 mm Ultra Low Carbon Steel Sheets Using O2 Assist Gas

International Nuclear Information System (INIS)

Salem, Hanadi G.; Abbas, Wafaa A.; Mansour, Mohy S.; Badr, Yehia A.

2007-01-01

There are many non-linear interaction factors responsible for the performance of the laser cutting process. Identification of the dominant factors that significantly affect the cut quality is important. In the current research, the gas pressure, laser power and scanning speed were selected as the cutting parameters. Effect of the cutting parameters on the cut quality was investigated, by monitoring the variation in hardness, oxide layer width and microstructural changes within the heat affected zone (HAZ). Results revealed that good quality cuts can be produced in ultra low carbon steel thin sheets, using CW Nd:YAG laser at a window of scanning speed ranging from 1100-1500 mm/min at a minimum heat input of 337watts under an assisting O2 gas pressure of 5 bar. Higher laser power resulted in either strengthening or softening in the HAZ surrounding the cut kerf. The oxide layer width is not affected by the energy density input but rather affected by the O2 gas pressure due to exothermal reaction

Multiple-objective optimization in precision laser cutting of different thermoplastics

Science.gov (United States)

Tamrin, K. F.; Nukman, Y.; Choudhury, I. A.; Shirley, S.

2015-04-01

Thermoplastics are increasingly being used in biomedical, automotive and electronics industries due to their excellent physical and chemical properties. Due to the localized and non-contact process, use of lasers for cutting could result in precise cut with small heat-affected zone (HAZ). Precision laser cutting involving various materials is important in high-volume manufacturing processes to minimize operational cost, error reduction and improve product quality. This study uses grey relational analysis to determine a single optimized set of cutting parameters for three different thermoplastics. The set of the optimized processing parameters is determined based on the highest relational grade and was found at low laser power (200 W), high cutting speed (0.4 m/min) and low compressed air pressure (2.5 bar). The result matches with the objective set in the present study. Analysis of variance (ANOVA) is then carried out to ascertain the relative influence of process parameters on the cutting characteristics. It was found that the laser power has dominant effect on HAZ for all thermoplastics.

Microstructural Evolution of AerMet100 Steel Coating on 300M Steel Fabricated by Laser Cladding Technique

Science.gov (United States)

Liu, Jian; Li, Jia; Cheng, Xu; Wang, Huaming

2018-02-01

In this paper, the process of coating AerMet100 steel on forged 300M steel with laser cladding was investigated, with a thorough analysis of the chemical composition, microstructure, and hardness of the substrate and the cladding layer as well as the transition zone. Results show that the composition and microhardness of the cladding layer are macroscopically homogenous with the uniformly distributed bainite and a small amount of retained austenite in martensite matrix. The transition zone, which spans approximately 100 μm, yields a gradual change of composition from the cladding layer to 300M steel matrix. The heat-affected zone (HAZ) can be divided into three zones: the sufficiently quenched zone (SQZ), the insufficiently quenched zone (IQZ), and the high tempered zone (HTZ). The SQZ consists of martensitic matrix and bainite, as for the IQZ and the HTZ the microstructures are martensite + tempered martensite and tempered martensite + ferrite, respectively. These complicated microstructures in the HAZ are caused by different peak heating temperatures and heterogeneous microstructures of the as-received 300M steel.

Experimental and numerical investigation on under-water friction stir welding of armour grade AA2519-T87 aluminium alloy

Directory of Open Access Journals (Sweden)

S. Sree Sabari

2016-08-01

Full Text Available Friction stir welding (FSW is a promising welding process that can join age hardenable aluminium alloys with high joint efficiency. However, the thermal cycles experienced by the material to be joined during FSW resulted in the deterioration of mechanical properties due to the coarsening and dissolution of strengthening precipitates in the thermo-mechanical affected zone (TMAZ and heat affected zone (HAZ. Under water friction stir welding (UWFSW is a variant of FSW process which can maintain low heat input as well as constant heat input along the weld line. The heat conduction and dissipation during UWFSW controls the width of TMAZ and HAZ and also improves the joint properties. In this investigation, an attempt has been made to evaluate the mechanical properties and microstructural characteristics of AA2519-T87 aluminium alloy joints made by FSW and UWFSW processes. Finite element analysis has been used to estimate the temperature distribution and width of TMAZ region in both the joints and the results have been compared with experimental results and subsequently correlated with mechanical properties.

SCC crack propagation behavior in 316L weld metal under high temperature water

International Nuclear Information System (INIS)

Nakade, Katsuyuki; Hirasaki, Toshifumi; Suzuki, Shunichi; Takamori, Kenro; Kumagai, Katsuhiko; Tanaka, Yoshihiko; Umeoka, Kuniyoshi

2008-01-01

Intergranular stress corrosion cracking (SCC) of 316L weld metal is of concern to the BWR plants. PLR pipes in commercial BWR plants have shown SCC in almost HAZ area in high temperature water, whereas, SCC has been arrested around fusion boundary for long time in the actual PLR pipe. The SCC behavior could be characterized in terms of dendrite direction, which was defined as the angle between dendrite growth direction and macro-SCC direction. In this study, the relationship between dendrite growth direction and macro-SCC direction was clearly showed on the fracture surface. The relative large difference of SCC susceptibility of 316L HAZ and weld metal was observed on the fracture surface. In the case of 0 degree, SCC has rapidly propagated into the weld metal parallel to the dendrite structure. In the case of more than 30 degree SCC direction, SCC was arrested around fusion area, and 60 degree SCC was drastically arrested around the fusion area. The large inclined dendrite structure for SCC is highly resistant to SCC. (author)

Stress corrosion crack growth rate in dissimilar metal welds; Evolucion microestructural de la ZAC en la union soldada con MIG sobre una aleacion del aluminio AA7020

Energy Technology Data Exchange (ETDEWEB)

Bloem, C. A.; Salvador, M. D.; Amigo, V.; Busquets, D.

2003-07-01

The aim of the present study is to evaluate the changes through the HAZ, analyzed under two different but complementary techniques. These are Transmission Electronic Microscopy (TEM) and Differential Scanning Calorimetry (DSC). The results shown that there are remarkable changes in size and morphology of the precipitates, being in accordance with the results obtained by DSC. (Author) 10 refs.

Stress corrosion crack growth rate in dissimilar metal welds

International Nuclear Information System (INIS)

Bloem, C. A.; Salvador, M. D.; Amigo, V.; Busquets, D.

2003-01-01

The aim of the present study is to evaluate the changes through the HAZ, analyzed under two different but complementary techniques. These are Transmission Electronic Microscopy (TEM) and Differential Scanning Calorimetry (DSC). The results shown that there are remarkable changes in size and morphology of the precipitates, being in accordance with the results obtained by DSC. (Author) 10 refs

Optimización del recorrido y de la potencia de un haz láser de CO2 en el tratamiento térmico de válvulas de motores diesel

Directory of Open Access Journals (Sweden)

Tobar, M. J.

2005-12-01

álvula. La resolución de la ecuación de conducción del calor se presenta complicada, en el momento en el que se incluyen propiedades termofísicas dependientes de la temperatura y una descripción realista de la geometría de la pieza. En la modelización es necesario utilizar métodos numéricos y se ha escogido, en este caso, el Método de los Elementos Finitos en el marco del programa comercial ANSYS®. La aplicación del estudio paramétrico, tanto numérico como experimental, previamente realizado sobre probetas planas a geometrías más complejas, requiere de un ajuste fino de esos parámetros para conseguir resultados comparables y tratamientos equivalentes. Entre otros aspectos del problema cabe resaltar la necesidad de obtener un mapa de isotermas paralelo a la superficie tratada; además la naturaleza circular de la trayectoria que recorre por completo el asiento de la válvula hace que el haz láser, hacia el final de su trayectoria, vuelva sobre el punto inicial, pasando por puntos que ya han sido calentados en el arranque del proceso, por lo tanto el suministro de potencia sobre la pieza ha de adaptarse a estas nuevas condiciones. Evidentemente, es necesario realizar la simulación de la transición de fase, lo que se consigue con las propiedades termofísicas adecuadas y una correcta estimación del coeficiente de absorción en cada una de las fases. Este trabajo muestra las ventajas del modelado teórico como apoyo para la optimización del tratamiento térmico superficial por láser de piezas de geometría compleja partiendo de validaciones realizadas en piezas más sencillas.

Growth, immune and viral responses in HIV infected African children receiving highly active antiretroviral therapy: a prospective cohort study

Directory of Open Access Journals (Sweden)

Bagenda Danstan

2010-08-01

Full Text Available Abstract Background Scale up of paediatric antiretroviral therapy in resource limited settings continues despite limited access to routine laboratory monitoring. We documented the weight and height responses in HIV infected Ugandan children on highly active antiretroviral therapy and determined clinical factors associated with successful treatment outcomes. Methods A prospective cohort of HIV infected children were initiated on HAART and followed for 48 weeks. Body mass index for age z scores(BAZ, weight and height-for-age z scores (WAZ & HAZ were calculated: CD4 cell % and HIV-1 RNA were measured at baseline and every 12 weeks. Treatment outcomes were classified according to; both virological and immunological success (VS/IS, virological failure and immunological success (VF/IS. virological success and immunological failure (VS/IF and both virological and immunological failure (VF/IF. Results From March 2004 until May 2006, 124 HIV infected children were initiated on HAART. The median age (IQR was 5.0 years (2.1 - 7.0 and 49% (61/124 were female. The median [95% confidence interval (CI] BAZ, WAZ and HAZ at baseline were 0.29 (-2.9, -1.2, -1.2 (-2.1, -0.5 and -2.06 (-2.9, -1.2 respectively. Baseline median CD4 cell % and log10 HIV-1 RNA were; 11.8% (7.5-18.0 and 5.6 (5.2-5.8 copies/ml. By 48 weeks, mean WAZ and HAZ in the VF/IS group, which was younger, increased from - 0.98 (SD 1.7 to + 1.22 (SD 1.2 and from -1.99 (1.7 to + 0.76 (2.4 respectively. Mean increase in WAZ and HAZ in the VS/IF group, an older group was modest, from -1.84 (1.3 to - 0.41 (1.2 and -2.25 (1.2 to -1.16 (1.3 respectively. Baseline CD4 cell % [OR 6.97 95% CI (2.6 -18.6], age [OR 4.6 95% CI (1.14 -19.1] and WHO clinical stage [OR 3.5 95%CI (1.05 -12.7] were associated with successful treatment outcome. Conclusions HIV infected Ugandan children demonstrated a robust increase in height and weight z scores during the first 48 weeks of HAART, including those who failed to

Application of Leak Before Break concept in 316LN austenitic steel pipes welded using 316L; Aplicação do conceito 1vazamento antes da falha' (Leak Before Break) em tubulações de aço 316LN soldado com metal de adição 316L

Energy Technology Data Exchange (ETDEWEB)

Cunto, Gabriel Giannini de

2017-07-01

This work presents a study of application of the Leak Before Break (LBB) concept, usually applied in nuclear power plants, in a pipe made from steel AISI type 316LN welded a coated electrode AISI type 316L. LBB concept is a criterion based on fracture mechanics analysis to show that a crack leak, present in a pipe, can be detected by leak detection systems, before this crack reaches a critical size that results in pipe fail. In the studied pipe, tensile tests and Ramberg-Osgood analyses were performed, as well as fracture toughness tests for obtaining the material resistance curve J-R. The tests were performed considering the base metal, weld and heat affected zone (HAZ), at the same operating temperatures of a nuclear power plant. For the mechanical properties found in these tests, load limit analyses were performed in order to determine the size of a crack which could cause a detectable leakage and the critical crack size, considering failure by plastic collapse. For the critical crack size found in the weld, which is the region that presented the lowest toughness, Integral J and tearing modulus T analyses were performed, considering failure by tearing instability. Results show a well-defined behavior between the base metal, HAZ and weld zones, where the base metal has a high toughness behavior, the weld has a low toughness behavior and the HAZ showed intermediate mechanical properties between the base metal and the weld. Using the PICEP software, the leak rate curves versus crack size and also the critical crack size were determined by considering load limit analysis. It was observed that after a certain crack size, the leak rate in base metal is much higher than for the HAZ and the weld, considering the same crack length. This occurs because in the base metal crack, it is expected that the crack grows in a more rounded form due to its higher toughness. The lowest critical crack size was found for the base metal presenting circumferential cracks. For the

A microstructural study of F82H-MOD. Plate, powder HIP and EB and TIG weldments

International Nuclear Information System (INIS)

Schuring, E.W.

1998-06-01

F82H is the heat identification number of a ferritic/martensitic steel. The steel has a chemical composition resulting in low activation after neutron irradiation. At ECN a microstructural study was conducted on plates of F82H (73, 15 and 25mm thick), a bar of HIPped F82H and EB and TIG welds in F82H plates. The investigation was aimed to characterise the microstructures for reference in irradiation experiments. The F82H mod. plates have a martensitic matrix with carbide precipitation on the prior austenite grain boundaries and the martensite laths. The carbide precipitation is most pronounced on the prior austenite grain boundaries. The PAG is comparable for the three plate thicknesses investigated. In two plates faint segregation bands were found with a denser carbide precipitation and 8-ferrite. Further Ta, Ti and Zr containing oxides are present. Hardness measurements show a higher overall hardness in the 25mm plate investigated compared to the 7.5 and 15mm plates. The F82H HIP bar shows a homogeneous PAG throughout the diameter. The microstructure shows a zone starting at about 1 mm below the surface with a width of 14mm, with a relatively high concentration of low precipitation density ferritic like fields, which corresponds to a zone with a 15HV5 lower hardness with respect to the rest of the bar. This zone is expected to be related to the HIP process. Further in the microstructure a circular pattern of W and Ta enriched inclusions is found, which mark the original HIP-powder grain boundaries. The EB-welds were manufactured by two manufactures and differ mostly in the heat input, resulting in differences in HAZ-width and the width of the weld cap. The F82H EB welds show comparable microstructures in the weld pool, with a martensitic microstructure free of carbides. All EB-welds contain 8-ferrite in concentrations of 0.1-1%. In the heat affected zone (HAZ), the coarse grained HAZ (CGHAZ) is free of carbide precipitation, whereas the fine grained HAZ (FGHAZ

Gender discrimination in undernutrition with mediating factors among Bengalee school children from Eastern India.

Science.gov (United States)

Mondal, Prakash Ranjan; Biswas, Sadaruddin; Bose, Kaushik

2012-04-01

This study was undertaken to determine age and sex variations in the prevalence of underweight and stunting, and to assess the impact of some socio-economic variables on undernutrition among 6-16 year old school children of Bengalee ethnicity in Chapra, West Bengal, India. The subjects were selected randomly from various schools and madrassas of the Chapra Block. A total of 725 children (342 boys and 383 girls) aged 6-16 years were measured and data on their socio-economic status were collected. Age and sex combined rates of underweight and stunting were 44.40% and 37.20%, respectively. Weight-for-age Z-score (WAZ) showed significant association with per-capita income (PCI) among boys (F=5.45) and girls (F=8.14). Height-for-age Z-score (HAZ) has also shown the association with per-capita income among boys (F=4.43) and girls (F=9.69). The WAZ was significantly associated with fathers' educational status (FOS) (t=-2.95) and the number of living rooms (NLR) (t=-2.91) among girls. The HAZ showed significant association with number of siblings (NS) among girls (F=4.25). Linear regression analyses revealed that NLR (t=2.04) and NS (t=1.95) had a significant impact on HAZ among boys. Among girls, PCI (t=3.38), FOS (t=2.87) and NLR (t=2.81) had a significant impact on WAZ and also PCI (t=3.28) and FOS (t=2.90) had a significant impact on HAZ. NLR had significant associations with underweight (χ(2)=3.59) and stunting (χ(2)=4.20) among boys. Among girls, PCI had significant associations with underweight (χ(2)=11.15) and stunting (χ(2)=11.64). FOS also showed significant associations with underweight (χ(2)=8.10) as well as stunting (χ(2)=8.28) among girls. NLR showed a significant association with underweight (χ(2)=7.75). Logistics regression analyses revealed that FOS (Wald=8.00) and NLR (Wald=4.09) were significant predictors of stunting among boys. Among girls, PCI was a significant predictor of underweight (Wald=10.95) as well as stunting (Wald=10.45). FOS, NLR and

Differential effects of young maternal age on child growth

Directory of Open Access Journals (Sweden)

Soo Hyun Yu

2016-11-01

Full Text Available Background: The association of early maternal birthing age with smaller children has been widely observed. However, it is unclear if this is due to confounding by factors such as socioeconomic status, or the age at which child growth restriction first occurs. Objective: To examine the effect of early maternal birthing age on the first-born child's height-for-age in a sample of developing countries in Africa, Asia, and Latin America. Design: Cross-sectional data from Demographic Health Surveys from 18 countries were used, to select the first-born child of mothers aged 15–24 years and a range of potential confounding factors, including maternal height. Child length/height-for-age z-scores (HAZs was estimated in age bands of 0–11, 12–23, 24–35, 36–47, and 48–59 months; HAZ was first compared between maternal age groups of 15–17, 18–19, and 20–24 years. Results: 1 There were significant bivariate associations between low child HAZ and young maternal age (71 of 180 possible cases; at p<0.10, but the majority of these did not persist when controlling for confounders (41 cases, 23% of the 180. 2 For children <12 months, when controlling for confounders, three out of seven Asian countries showed a significant association between lower infant HAZ and low maternal age, as did six out of nine African countries (15–17 or 15–19 years vs. the older group. 3 The association (adjusted continued after 24 months in 12 of the 18 countries, in Africa, Asia, and Latin America. 4 The stunting differences for children between maternal age groups were around 9 percentage points (ppts in Asia, 14 ppts in Africa, and 10 ppts in Latin America. These data do not show whether this is due to, for example, socioeconomic factors that were not included, an emerging effect of intrauterine growth restriction, or the child feeding or caring behaviors of young mothers. The latter is considered to be the most likely. Conclusions: The effect of low maternal age

Application of Leak Before Break concept in 316LN austenitic steel pipes welded using 316L

International Nuclear Information System (INIS)

Cunto, Gabriel Giannini de

2017-01-01

This work presents a study of application of the Leak Before Break (LBB) concept, usually applied in nuclear power plants, in a pipe made from steel AISI type 316LN welded a coated electrode AISI type 316L. LBB concept is a criterion based on fracture mechanics analysis to show that a crack leak, present in a pipe, can be detected by leak detection systems, before this crack reaches a critical size that results in pipe fail. In the studied pipe, tensile tests and Ramberg-Osgood analyses were performed, as well as fracture toughness tests for obtaining the material resistance curve J-R. The tests were performed considering the base metal, weld and heat affected zone (HAZ), at the same operating temperatures of a nuclear power plant. For the mechanical properties found in these tests, load limit analyses were performed in order to determine the size of a crack which could cause a detectable leakage and the critical crack size, considering failure by plastic collapse. For the critical crack size found in the weld, which is the region that presented the lowest toughness, Integral J and tearing modulus T analyses were performed, considering failure by tearing instability. Results show a well-defined behavior between the base metal, HAZ and weld zones, where the base metal has a high toughness behavior, the weld has a low toughness behavior and the HAZ showed intermediate mechanical properties between the base metal and the weld. Using the PICEP software, the leak rate curves versus crack size and also the critical crack size were determined by considering load limit analysis. It was observed that after a certain crack size, the leak rate in base metal is much higher than for the HAZ and the weld, considering the same crack length. This occurs because in the base metal crack, it is expected that the crack grows in a more rounded form due to its higher toughness. The lowest critical crack size was found for the base metal presenting circumferential cracks. For the

Mathematical modeling for prediction and optimization of TIG welding pool geometry

Directory of Open Access Journals (Sweden)

U. Esme

2009-04-01

Full Text Available In this work, nonlinear and multi-objective mathematical models were developed to determine the process parameters corresponding to optimum weld pool geometry. The objectives of the developed mathematical models are to maximize tensile load (TL, penetration (P, area of penetration (AP and/or minimize heat affected zone (HAZ, upper width (UW and upper height (UH depending upon the requirements.

Construction safety in DOE. Part 1, Students guide

Energy Technology Data Exchange (ETDEWEB)

Handwerk, E C

1993-08-01

This report is the first part of a compilation of safety standards for construction activities on DOE facilities. This report covers the following areas: general safety and health provisions; occupational health and environmental control/haz mat; personal protective equipment; fire protection and prevention; signs, signals, and barricades; materials handling, storage, use, and disposal; hand and power tools; welding and cutting; electrical; and scaffolding.

Fundamental Studies on Phase Transformations and Mechanical Properties of Fusion Welds in Advanced Naval Steels

Science.gov (United States)

2017-07-31

naval and structural applications. However, prior to this research project, a fundamental understanding of the phase transformation behavior under the...prior to this research project, a fundamental understanding of the phase transformation behavior under the high heating and cooling rates associated...HAZ mechanical properties. Such a treatment is expensive, time consuming , and cannot be practically applied to large structures. However, the absence

Avaliação da suscetibilidade à corrosão sob tensão da ZAC do aço inoxidável AISI 316L em ambiente de reator nuclear PWR Stress corrosion cracking of stainless steel AISI 316L HAZ in PWR Nuclear reactor environment

Directory of Open Access Journals (Sweden)

Mônica Maria de Abreu Mendonça Schvartzman

2009-09-01

Full Text Available Aços carbono de baixa liga e aços inoxidáveis são amplamente utilizados nos circuitos primários de reatores nucleares do tipo PWR (Pressurized Water Reactor. Ligas de níquel são empregadas na soldagem destes materiais devido a características como elevadas resistências mecânica e à corrosão, coeficiente de expansão térmica adequado, etc. Nos últimos 30 anos, a corrosão sob tensão (CST tem sido observada principalmente nas regiões das soldas entre materiais dissimilares existentes nestes reatores. Este trabalho teve como objetivo avaliar, por comparação, a suscetibilidade à corrosão sob tensão da zona afetada pelo calor (ZAC do aço inoxidável austenítico AISI 316L quando submetida a um ambiente similar ao do circuito primário de um reator nuclear PWR nas temperaturas de 303ºC e 325ºC. Para esta avaliação empregou-se o ensaio de taxa de deformação lenta - SSRT (Slow Strain Rate Test. Os resultados indicaram que a CST é ativada termicamente e que a 325ºC pode-se observar a presença mais significativa de fratura frágil decorrente do processo de corrosão sob tensão.In pressurized water reactors (PWRs, low alloy carbon steels and stainless steel are widely used in the primary water circuits. In most cases, Ni alloys are used to joint these materials and form dissimilar welds. These alloys are known to accommodate the differences in composition and thermal expansion of the two materials. Stress corrosion cracking of metals and alloys is caused by synergistic effects of environment, material condition and stress. Over the last thirty years, CST has been observed in dissimilar metal welds. This study presents a comparative work between the CST in the HAZ (Heat Affected Zone of the AISI 316L in two different temperatures (303ºC and 325ºC. The susceptibility to stress corrosion cracking was assessed using the slow strain rate tensile (SSRT test. The results of the SSRT tests indicated that CST is a thermally

İşbirliği İle Bireyselleştirilmiş Eğitim Programı Geliştirme Süreci: Durum Çalışması

Directory of Open Access Journals (Sweden)

Sezgin Vuran

2017-07-01

Full Text Available Bu çalışmanın amacı Zihin Engelliler Öğretmenliği Programı öğretmen adaylarının Bireyselleştirilmiş Eğitim Programlarının Hazırlanması ve Öğretimin Bireyselleştirilmesi dersinde, işbirliği ile Bireyselleştirilmiş Eğitim Programları (BEP geliştirmeleri ve bir ekiple birlikte çalışma becerilerini kazanmaları sürecinin ve sonuçlarının betimlenmesidir. Çalışma nitel araştırma yöntemi olan durum çalışması olarak yürütülmüştür. Çalışmaya toplam 100 öğretmen adayı ve üç öğretim elemanı katılmıştır. Çalışmada veriler; katılımcı gözlem, saha notları, öğretmen adayı ödevleri, öğretmen adayı günlükleri ve öğretim elemanı görüşleri kullanılarak toplanmıştır. Toplanan veriler içerik analizi yapılarak analiz edilmiştir. Çalışmada uygulama sürecinde işbirliği ile öğretim ve öğrenme yaklaşımları benimsenmiştir. İşbirliği ile öğrenme yolu ile ekip üyelerinin BEP hazırlama becerilerin gelişmesinin yanı sıra BEP’in önemli gerekliliklerinden biri olan ekiple çalışma becerileri de gelişmiştir. Ayrıca dersin işbirliği ile öğretim yolu ile yürütülmesi öğretmen adaylarına işbirliği ile çalışmaya iyi bir model oluşturmuştur. Bu çalışma sonucunda öğretmen adayları hem bireysel hem grup olarak BEP hazırlama aşamalarını izleyerek özel gereksinimi olan bir öğrencinin gereksinimlerine uygun bir BEP hazırlamışlar ve öğretim uyarlamaları yapmışlardır. Ek olarak, işbirliği ile BEP hazırlama sürecinde öğretmen adaylarının birbirleriyle etkili bir iletişim kurdukları ve oldukça hevesli şekilde derse katıldıkları gözlenmiştir. Bu çalışmanın bulguları öğretmen adaylarının ileride yaşayabilecekleri zorluklarla baş etmeleri ve sürece hazırlanmaları için öğretmenlere yardımcı olacaktır. The purpose of this study is to reveal the process and the results of the development of an

The Characteristics of Welding Joint on Stainless Steel as a Candidate of High Level Waste Canister

International Nuclear Information System (INIS)

Aisyah; Herlan-Martono

2000-01-01

High level waste is the waste generated from reprocessing of the spent fuels. This type of waste is vitrified with borosilicate glass to become waste-glass. This waste glass is contained in a canister made of austenitic stainless steel. The canister material is subjected to be welded during fabrication and utilization. The character of the welding joint that is the function of the electrical current used in the welding process have been studied. The strength of the joint is tested mechanically i.e.: the tensile strength and hardness test. The result shows that the higher the current used in welding process, the better the strength of the joint and as well the tensile strength. The optimum current is 110 A. From the hardness test, it was figured that the length of the HAZ area is 14 mm. The material in HAZ area is the hardest compared to the others, it is due to the appearance of the chrome-carbide. The welding of the canister with such a condition, during fabrication as well as during the utilization of the canister for the container of the high level waste with the PWHT process gives better result. (author)

Understanding the complex determinants of height and adiposity in disadvantaged daycare preschoolers in Salvador, NE Brazil through structural equation modelling.

Science.gov (United States)

Lander, Rebecca L; Williams, Sheila M; Costa-Ribeiro, Hugo; Mattos, Angela P; Barreto, Danile L; Houghton, Lisa A; Bailey, Karl B; Lander, Alastair G; Gibson, Rosalind S

2015-10-23

Earlier we reported on growth and adiposity in a cross-sectional study of disadvantaged Brazilian preschoolers. Here we extend the work on these children, using structural equation modelling (SEM) to gather information on the complex relationships between the variables influencing height and adiposity. We hope this information will help improve the design and effectiveness of future interventions for preschoolers. In 376 preschoolers aged 3-6 years attending seven philanthropic daycares in Salvador, we used SEM to examine direct and indirect relationships among biological (sex, ethnicity, birth order, maternal height and weight), socio-economic, micronutrient (haemoglobin, serum selenium and zinc), and environmental (helminths, de-worming) variables on height and adiposity, as reflected by Z-scores for height-for-age (HAZ) and body mass index (BMIZ). Of the children, 11 % had HAZ  1. Of their mothers, 8 % had short stature, and 50 % were overweight or obese. Based on standardized regression coefficients, significant direct effects (p growth, helminth infection was a modifiable risk factor directly and indirectly affecting HAZ and BMIZ, respectively. Hence the WHO de-worming recommendation should include preschoolers living in at-risk environments as well as school-aged children.

Infrastructure mitigates the sensitivity of child growth to local agriculture and rainfall in Nepal and Uganda.

Science.gov (United States)

Shively, Gerald E

2017-01-31

This paper investigates linear growth and weight gain among 11,946 children below the age of 5 y in Nepal and Uganda, testing the hypothesis that child growth is sensitive to precipitation during key periods in a child's early life. The paper also tests the importance of the economic and physical environments in which children reside. Outcomes are not completely explained by agricultural performance or the observed characteristics of children or their households. Associations between height-for-age z-score (HAZ) and weight-for-height z-score (WHZ) and rainfall are generally positive, but patterns are heterogeneous. At the mean, an increase of 1 SD in agricultural season rainfall is associated with a 0.05- to 0.25-point higher z-score, which translates into increases of roughly 4-13% for HAZ and 1-7% for WHZ. Nutrition sensitivity to rainfall is greater in Nepal, where rainfall is lower on average and wider ranging, than in Uganda. Health and transport infrastructure help to buffer children from the deleterious nutritional effects of precipitation shortfalls, underscoring the role of broadly based economic development in promoting child nutrition.

Influences of Laser Spot Welding on Magnetic Property of a Sintered NdFeB Magnet

Directory of Open Access Journals (Sweden)

Baohua Chang

2016-08-01

Full Text Available Laser welding has been considered as a promising method to join sintered NdFeB permanent magnets thanks to its high precision and productivity. However, the influences of laser welding on the magnetic property of NdFeB are still not clear. In the present paper, the effects of laser power on the remanence (Br were experimentally investigated in laser spot welding of a NdFeB magnet (N48H. Results show that the Br decreased with the increase of laser power. For the same welding parameters, the Br of magnets, that were magnetized before welding, were much lower than that of magnets that were magnetized after welding. The decrease in Br of magnets after laser welding resulted from the changes in microstructures and, in turn, the deterioration of magnetic properties in the nugget and the heat affected zone (HAZ in a laser weld. It is recommended that the dimensions of nuggets and HAZ in laser welds of a NdFeB permanent magnet should be as small as possible, and the magnets should be welded before being magnetized in order to achieve a better magnetic performance in practical engineering applications.

Microstructure and mechanical properties of the TIG welded joints of fusion CLAM steel

Energy Technology Data Exchange (ETDEWEB)

Jiang Zhizhong, E-mail: zhizhongjiang2006@yahoo.com.c [School of Materials Science and Engineering, University of Science and Technology Beijing, Xueyuan Road, Beijing 100083 (China); Ren Litian; Huang Jihua; Ju Xin; Wu Huibin [School of Materials Science and Engineering, University of Science and Technology Beijing, Xueyuan Road, Beijing 100083 (China); Huang Qunying; Wu Yican [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui 230031 (China)

2010-12-15

The CLAM steel plates were butt-welded through manual tungsten inert gas welding (TIG) process, and the following post-welding heat treatment (PWHT) at 740 {sup o}C for 1 h. The microstructure and mechanical properties of the welded joints were measured. The results show that both hardening and softening occur in the weld joints before PWHT, but the hardening is not removed completely in the weld metal and the fusion zone after PWHT. In as-welded condition, the microstructure of the weld metal is coarse lath martensite, and softened zone in heat-affected zone (HAZ) consists of a mixture of tempered martensite and ferrite. After PWHT, a lot of carbides precipitate at all zones in weld joints. The microstructure of softened zone transforms to tempered sorbite. Tensile strength of the weld metal is higher than that of HAZ and base metal regardless of PWHT. However, the weld metal has poor toughness without PWHT. The impact energy of the weld metal after PWHT reaches almost the same level as the base metal. So it is concluded that microstructure and mechanical properties of the CLAM steel welded joints can be improved by a reasonable PWHT.

Effect of zirconium addition on welding of aluminum grain refined by titanium plus boron

Science.gov (United States)

Zaid, A. I. O.

2014-06-01

Aluminum oxidizes freely in ordinary atmosphere which makes its welding difficult and weak, particularly it solidifies in columnar structure with large grains. Therefore, it is anticipated that the effect of addition of some grain refiners to its melt before solidification is worth while investigating as it may enhance its weldabilty and improve its mechanical strength. In this paper, the effect of addition of zirconium at a weight of 0.1% (which corresponds to the peretictic limit on the aluminum-zirconium base phase diagram) to commercially pure aluminum, grain refined by Ti+B on its weldability, using gas tungsten arc welding, GTAW, method which was formerly known as TIG. A constant current level of 30 AC Ampere was used because it removes the oxides during the welding process. Metallographic examination of the weldments of the different combinations of Al with Al and Al with its microalloys: in the heat affected zone, HAZ, and away from it was carried out and examined for HAZ width, porosity, cracks and microhardness. It was found that grain refining by Ti+B or Zr resulted in enhancement of the weldment.

Effect of zirconium addition on welding of aluminum grain refined by titanium plus boron

International Nuclear Information System (INIS)

Zaid, A. I. O.

2013-01-01

Aluminum oxidizes freely in ordinary atmosphere which makes its welding difficult and weak, particularly it solidifies in columnar structure with large grains. Therefore, it is anticipated that the effect of addition of some grain refiners to its melt before solidification is worth while investigating as it may enhance its weldabilty and improve its mechanical strength. In this paper, the effect of addition of zirconium at a weight of 0.1 percentage (which corresponds to the peretictic limit on the aluminum-zirconium base phase diagram) to commercially pure aluminum, grain refined by Tau i+Beta on its weldability, using gas tungsten arc welding, GTAW, method which was formerly known as TIG. A constant current level of 30 AC Ampere was used because it removes the oxides during the welding process. Metallographic examination of the weldments of the different combinations of Al with Al and Al with its microalloys: in the heat affected zone, HAZ, and away from it was carried out and examined for HAZ width, porosity, cracks and microhardness. It was found that grain refining by Tau i+Beta or Zr resulted in enhancement of the weldment. (author)

Effect of zirconium addition on welding of aluminum grain refined by titanium plus boron

International Nuclear Information System (INIS)

Zaid, A I O

2014-01-01

Aluminum oxidizes freely in ordinary atmosphere which makes its welding difficult and weak, particularly it solidifies in columnar structure with large grains. Therefore, it is anticipated that the effect of addition of some grain refiners to its melt before solidification is worth while investigating as it may enhance its weldabilty and improve its mechanical strength. In this paper, the effect of addition of zirconium at a weight of 0.1% (which corresponds to the peretictic limit on the aluminum-zirconium base phase diagram) to commercially pure aluminum, grain refined by Ti+B on its weldability, using gas tungsten arc welding, GTAW, method which was formerly known as TIG. A constant current level of 30 AC Ampere was used because it removes the oxides during the welding process. Metallographic examination of the weldments of the different combinations of Al with Al and Al with its microalloys: in the heat affected zone, HAZ, and away from it was carried out and examined for HAZ width, porosity, cracks and microhardness. It was found that grain refining by Ti+B or Zr resulted in enhancement of the weldment

Twin-spot laser welding of advanced high-strength multiphase microstructure steel

Science.gov (United States)

Grajcar, Adam; Morawiec, Mateusz; Różański, Maciej; Stano, Sebastian

2017-07-01

The study addresses the results concerning the laser welding of TRIP (TRansformation Induced Plasticity) steel using a beam focused at two spots (also referred to as twin-spot laser welding). The analysis involved the effect of variable welding thermal cycles on the properties and microstructure of welded joints. The tests were performed using a linear energy of 0.048 and 0.060 kJ/mm and the laser beam power distribution of 50%:50%, 60%:40% and 70%:30%. The tests also involved welding performed using a linear energy of 0.150 kJ/mm and the laser beam power distribution of 70%:30%. In addition, the research included observations of the microstructure of the fusion zone, heat affected zone and the transition zone using light microscopy and scanning electron microscopy. The fusion zone was composed of blocky-lath martensite whereas the HAZ (heat-affected zone) was characterised by the lath microstructure containing martensite, bainite and retained austenite. The distribution of twin-spot laser beam power significantly affected the microstructure and hardness profiles of welded joints. The highest hardness (480-505 HV), regardless of welding variants used, was observed in the HAZ.

Study of MA Effect on Yield Strength and Ductility of X80 Linepipe Steels Weld

Science.gov (United States)

Huda, Nazmul; Lazor, Robert; Gerlich, Adrian P.

2017-09-01

Multipass GMAW (Gas Metal Arc Welding) welding was used to join X80 linepipe materials using two weld metals of slightly different compositions. Welding wires with diameters of 0.984 and 0.909 mm were used while applying the same heat input in each pass. The slight difference in the wire diameters resulted in different HAZ microstructures. The microstructures in the doubly reheated HAZ of both welds were found to contain bainite-ferrite. However, etching also revealed a difference in martensite-austenite (MA) fraction in these reheated zones. The MA exhibited twice the hardness of ferrite when measured by nanoindentation. Tensile testing from the reheated zone of both welds revealed a difference in yield strength, tensile strength and elongation of the transverse weld specimens. In the reheated zone of weld A, (produced with a 0.984 mm wire) a higher fraction of MA was observed, which resulted in higher strength but lower elongation compared to weld B. The ductility of weld A was found severely impaired (to nearly half of weld B) due to formation of closely spaced voids around the MA, along with debonding of MA from the matrix, which occurs just above the yield stress.

How to avoid the generation of logic loops in the construction of fault trees

International Nuclear Information System (INIS)

Demichela, M.; Piccinini, N.; Ciarambino, I.; Contini, S.

2004-01-01

Generation of an infinite series of identical sub-trees may occur during the construction of a Fault Tree (FT) when one item of equipment in a plant is considered several times in the same sub-tree in the course of the tree extraction from a HazOp (Hazard Operability analysis) analysis. Generation of loops in the construction of an FT can be avoided by means of an ad hoc logical analysis in which certain simple rules of syntax are taken into account. A radical solution, however, can be obtained if identification of unwanted events in a process plant is not undertaken with conventional procedures, such as HazOp (Operability Analysis with guide words, failure mode and effect analysis (FMEA) etc.), but with a more modern and structured version, such as Recursive Operability Analysis (ROA), which is both systematic and complete, and allows direct extraction of logic trees, (FT, event trees, etc.) for subsequent quantification. This feature means that, by contrast with conventional operability analysis, the congruence of the ROA itself can be checked. The ROA method is illustrated in this paper with the aid of some simple examples

Optical interrupter based in the internal total reflection of spatial solitons at nonlinear saturable interfaces; Interruptores opticos basados en reflexion interna total de solitones espaciales en interfaces no lineales saturables

Energy Technology Data Exchange (ETDEWEB)

Alvarado-Mendez, E.; Torres-Cisneros, M.; Gutierrez-Hernandez, D. A.; Andrade-Lucio, J. A.; Rojas-Lagunas, R.; Pedraza-Ortega, J. C.; Torres Cisneros, G. E. [Universidad de Guanajuato, Guanajuato (Mexico); Sanchez Mondragon, J. J. [Universidad Autonoma del Estado de Morelos, Morelos (Mexico); Flores-Alvarado, G. [Preparatoria por Cooperacion Domingo Arenas, Tlaxcala (Mexico)

2001-06-01

We study the reflection of one-dimensional spatial soliton at the nonlinear interface between a saturable type medium and linear medium. Our study makes emphasis on determining the physical conditions under which the beam reflected by the interface is still a spatial soliton. Depended the incidence angle we find three critical regions for spatial solitons in the interface. We observed nonlinear Goos- Haechen shift is determined if reflection angle are conserved. Finally, we present preliminary experimental results in SBN61:Ce of the total internal reflection of one dimensional beam. [Spanish] Estudiamos la reflexion de un soliton espacial unidimensional en una interfase formada por un medio no lineal saturable y un medio lineal. Nuestros estudios hacen enfasis en determinar las condiciones fisicas bajo las cuales el haz reflejado por la interfase no lineal sigue siendo soliton. Encontramos tres regiones criticas para un soliton especial en la interfase, dependiendo del valor que tome el angulo de incidencia. Asi mismo observamos corrimiento Goos-Haechen no lineal que es determinante para la conservacion del angulo de reflexion. Finalmente, presentamos resultados preliminares experimentales en SBN61:Ce de la reflexion interna total de un haz unidimensional.

Boundary and sub-boundary hardening in tempered martensitic 9Cr steel during long-term creep at 650 C

Energy Technology Data Exchange (ETDEWEB)

Abe, Fujio [National Institute for Materials Science, Sengen, Tsukuba (Japan)

2010-07-01

The boundary and sub-boundary hardening is shown to be the most important strengthening mechanism in creep of the 9% Cr steel base metal and welded joints. The addition of boron reduces the coarsening rate of M{sub 23}C{sub 6} carbides along boundaries near prior austenite grain boundaries during creep, enhancing the boundary and sub-boundary hardening. This improves long-term creep strength of base metal. The enhancement of boundary and sub-boundary hardening is significantly reduced in fine-grained region of Ac{sub 3} HAZ simulated specimens of conventional steel P92. In NIMS 9Cr boron steel welded joints, the grain size and distribution of carbonitrides are substantially the same between the HAZ and base metal, where fine carbonitrides are distributed along the lath and block boundaries as well as along prior austenite grain boundaries. This is essential for the suppression of Type IV fracture in NIMS 9% Cr boron steel welded joints. Newly alloy-designed 9Cr steel with 160 ppm boron and 85 ppm nitrogen exhibits much higher creep rupture strength of base metal than P92 and also no Tpe-IV fracture in welded joints at 650 C. (orig.)

Effects of heat input on mechanical properties of metal inert gas welded 1.6 mm thick galvanized steel sheet

International Nuclear Information System (INIS)

Rafiqul, M I; Ishak, M; Rahman, M M

2012-01-01

It is usually a lot easier and less expensive to galvanize steel before it is welded into useful products. Galvanizing afterwards is almost impossible. In this research work, Galvanized Steel was welded by using the ER 308L stainless steel filler material. This work was done to find out an alternative way of welding and investigate the effects of heat input on the mechanical properties of butt welded joints of Galvanized Steel. A 13.7 kW maximum capacity MIG welding machine was used to join 1.6 mm thick sheet of galvanized steel with V groove and no gap between mm. Heat inputs was gradually increased from 21.06 to 25.07 joules/mm in this study. The result shows almost macro defects free welding and with increasing heat input the ultimate tensile strength and welding efficiency decrease. The Vickers hardness also decreases at HAZ with increasing heat input and for each individual specimen; hardness was lowest in heat affected zone (HAZ), intermediate in base metal and maximum in welded zone. The fracture for all specimens was in the heat affected zone while testing in the universal testing machine.

Effects of heat input on mechanical properties of metal inert gas welded 1.6 mm thick galvanized steel sheet

Science.gov (United States)

Rafiqul, M. I.; Ishak, M.; Rahman, M. M.

2012-09-01

It is usually a lot easier and less expensive to galvanize steel before it is welded into useful products. Galvanizing afterwards is almost impossible. In this research work, Galvanized Steel was welded by using the ER 308L stainless steel filler material. This work was done to find out an alternative way of welding and investigate the effects of heat input on the mechanical properties of butt welded joints of Galvanized Steel. A 13.7 kW maximum capacity MIG welding machine was used to join 1.6 mm thick sheet of galvanized steel with V groove and no gap between mm. Heat inputs was gradually increased from 21.06 to 25.07 joules/mm in this study. The result shows almost macro defects free welding and with increasing heat input the ultimate tensile strength and welding efficiency decrease. The Vickers hardness also decreases at HAZ with increasing heat input and for each individual specimen; hardness was lowest in heat affected zone (HAZ), intermediate in base metal and maximum in welded zone. The fracture for all specimens was in the heat affected zone while testing in the universal testing machine.

SCC behavior of alloy 690 from a CDRM mock-up

International Nuclear Information System (INIS)

Lapena, J.; Sol Garcia-Redondo, M. del; Perosanz, F.J.; Saez, A.; Gomez-Briceno, D.; Castelao, C.

2015-01-01

Stress corrosion cracking (SCC) response of Alloy 690 when the material has been subjected to nonuniform cold working is of interest to understand the behavior of the weld heat affected zone (HAZ) of Alloy 690 in which localised plastic strain exists due to weld shrinkage. This has a special interest in the case of control-rod-drive mechanisms (CRDM) of vessel head. To simulate these conditions during last years many crack growth rate (CGR) data were obtained in deformed material by cold work (rolling, forging or tensile straining), up to 40% of cold working. However, it is unclear to what extent this simulation procedure reproduces the conditions of the material in a CRDM. A research project is being carried out in order to obtain CGR data in realistic situations existing in operating power plants, by the use of CT specimens extracted from CRDMs. This presentation shows the characterization and some results of crack growth rate data on Alloy 690 TT base metal/HAZ/weld metal using specimens made from a CRDM mock-up. It has been fabricated following the usual procedures used for the RPV head fabrication for the Spanish PWR NPP. (authors)

Association of maternal and child nutritional status in Brazil: a population based cross-sectional study.

Science.gov (United States)

Felisbino-Mendes, Mariana Santos; Villamor, Eduardo; Velasquez-Melendez, Gustavo

2014-01-01

Although child undernutrition and stunting has been decreasing worldwide while obesity rates increase, these extreme conditions might coexist in families from low- and middle-income countries. We examined the association between maternal and child anthropometric indicators using a population representative sample. 4,258 non-pregnant women and their children maternal height, body mass index (BMI), and waist circumference (WC). Adjusted mean differences and 95% confidence intervals (95% CI) were estimated from linear regression, taking into account the complex survey design. We also examined the associations of maternal anthropometry with the prevalence of child stunting (HAZobesity (BAZ>2). HAZ was positively associated with maternal height and WC in a linear fashion. After adjustment, for sociodemographic characteristics, children whose mothers' height wasmaternal height and maternal BMI, children of mothers with a waist circumference ≥88 cm had 0.3 higher HAZ than those of mothers with WCmaternal height (maternal BMI and WC. We observed a strong, positive association of maternal and child nutritional status. Mothers of low stature had children with lower stature, mothers with central obesity had taller children, and mothers with overall or abdominal obesity had children with higher BAZ.

Application of YAG laser cladding to the flange seating surface

International Nuclear Information System (INIS)

Nakanishi, Koki; Ninomiya, Kazuyuki; Nezaki, Koji

1999-01-01

Stainless cladding on carbon steel is usually conducted by shielded metal arc welding (SMAW) or gas tungsten arc welding (GTAW). YAG ( Yttrium-Aluminum-Garnet) laser welding is superior to these methods of welding in the following respects : (1) The heat affected zone (HAZ) is narrower and there is less distortion. (2) YAG laser cladding has the required chemical compositions, even with possibly fewer welding layers under controlled dilution. (3) Greater welding speed. YAG laser cladding application to vessel flange seating surfaces was examined in this study and the results are discussed. The following objectives were carried out : (1) Determination of welding conditions for satisfactory cladding layers and (2) whether cladding would be adequately possible at a cornered section of a stair-like plate, assuming actual flange shape. (3) Measurement of welding distortion and heat affected zone in carbon steel. The welding conditions for producing no-crack deposit with low dilution in carbon steel were clarified and welding by which cladding at cornered section would be possible was achieved. welding distortion by YAG laser was found less than with GTAW and HAZ made by first layer welding could be tempered appropriately by second layer welding. (author)

Microstructure and mechanical properties of resistance spot welded dissimilar thickness DP780/DP600 dual-phase steel joints

International Nuclear Information System (INIS)

Zhang, Hongqiang; Wei, Ajuan; Qiu, Xiaoming; Chen, Jianhe

2014-01-01

Highlights: • We examine changes of microstructure of dissimilar thickness DP600/DP780 joints. • The hardness profile of RSW joints can be predicted by the equation. • Failure modes, peak load and energy describes the mechanical properties of joints. • The nugget diameter is the key factor of transition between the failure modes. - Abstract: In this study, resistance spot welding (RSW) experiments were performed in order to evaluate the microstructure and mechanical properties of single-lap joints between DP780 and DP600. The results show that the weld joints consist of three regions including base metal (BM), heat affected zone (HAZ) and fusion zone (FZ). The grain size and martensite volume fractions increase in the order of BM, HAZ and FZ. The hardness in the FZ is significantly higher than hardness of base metals. Tensile properties of the joints were described in terms of the failure modes and static load-carrying capabilities. Two distinct failure modes were observed during the tensile shear test of the joints: interfacial failure (IF) and pullout failure (PF). The FZ size plays a dominate role in failure modes of the joints

Desensitization of stainless steels by laser surface heat-treatment

Energy Technology Data Exchange (ETDEWEB)

Nakao, Yoshikuni; Nishimoto, Kazutoshi

1987-11-01

Laser heating was applied for the desensitization heat-treatment of the surface layer in the sensitized HAZ of Type 304 stainless steel. The degree of sensitization was examined by EPR technique and the 10 % oxalic acid electrolytic etch test. The CO/sub 2/ laser with maximum power of 1.5 kW was used for heat-treatment. Time-Temperature-Desensitization diagram (TTDS diagram) for sensitized Type 304 stainless steels were developed by calculation assuming the chromium diffusion control for desensitization which might occur when the chromium depleted zone was healed up due to dissolution of chromium carbide and chromium diffusion from the matrix being heated at the solution annealing temperatures. TTDS diagrams calculated agree fairly well with ones determined by corrosion tests. Laser irradiation conditions (e.g., Laser power, beam diameter and traveling velocity) required for desensitization of sensitized Type 304 stainless steels were calculated using additivity rule from the TTDS diagram calculated and theoretical thermal curve of laser heating derived from the heat conduction theory. After laser beam irradiated under an optimum condition predicted by calculation, the sensitized HAZ of Type 304 stainless steel restored complete resistance to intergranular corrosion.

Simulation of Friction Stir Processing in 304L Stainless Steel

Directory of Open Access Journals (Sweden)

Miles M.P.

2016-01-01

Full Text Available A major dilemma facing the nuclear industry is repair or replacement of stainless steel reactor components that have been exposed to neutron irradiation. When conventional fusion welding is used for weld repair, the high temperatures and thermal stresses inherent in the process enhance the growth of helium bubbles, causing intergranular cracking in the heat-affected zone (HAZ. Friction stir processing (FSP has potential as a weld repair technique for irradiated stainless steel, because it operates at much lower temperatures than fusion welding, and is therefore less likely to cause cracking in the HAZ. Numerical simulation of the FSP process in 304L stainless steel was performed using an Eulerian finite element approach. Model input required flow stresses for the large range of strain rates and temperatures inherent in the FSP process. Temperature predictions in three locations adjacent to the stir zone were accurate to within 4% of experimentally measure values. Prediction of recrystallized grain size at a location about 6mm behind the tool center was less accurate, because the empirical model employed for the prediction did not account for grain growth that occurred after deformation in the experiment was halted.

Research on the Effects of Technical Parameters on the Molding of the Weld by A-TIG Welding

OpenAIRE

Shi, Kai; Pan, Wu

2012-01-01

The effects of welding parameters on the molding of weld by A-TIG welding of a 4mm thickness mild steel plate is studied in the present paper. The results obtained show that: as welding current increases A-TIG welding penetration gets deeper than TIG welding; size and shape of HAZ has remarkable change; A-TIG welding has the narrower weld pool width than TIG welding.

Weldability Characteristics of Construction Steels A36, A514, and A516.

Science.gov (United States)

1981-12-01

Headquarters *Except when preceded by a 2; in that case, it is high iron IHQ , DA, March 1968): Operator Manual: Welding Theory oxide. ac or dc, either...155.9 0.92 I ksi = 6.89 MPa 26 ?uie the properties of the weld metal and the HAZ to test results for the E7018 weld ! ? td and the A5 l tliv e required

Steels and welding nuclear

International Nuclear Information System (INIS)

Sessa, M.; Milella, P.P.

1987-01-01

This ENEA Data-Base regards mechanical properties, chemical composition and heat treatments of nuclear pressure vessel materials: type A533-B, A302-B, A508 steel plates and forgings, submerged arc welds and HAZ before and after nuclear irradiation. Irradiation experiments were generally performed in high flux material test reactors. Data were collected from international available literature about water nuclear reactors pressure vessel materials embrittlement

Microstructural Characterization of Clad Interface in Welds of Ni-Cr-Mo High Strength Low Alloy Steel

Energy Technology Data Exchange (ETDEWEB)

Kim, Hong-Eun; Kim, Min-Chul; Lee, Ho-Jin; Kim, Keong-Ho [KAERI, Daejeon (Korea, Republic of); Lee, Ki-Hyoung [KAIST, Daejeon (Korea, Republic of); Lee, Chang-Hee [Hanyang Univ., Seoul (Korea, Republic of)

2011-08-15

SA508 Gr.4N Ni-Cr-Mo low alloy steel, in which Ni and Cr contents are higher than in commercial SA508 Gr.3 Mn-Mo-Ni low alloy steels, may be a candidate reactor pressure vessel (RPV) material with higher strength and toughness from its tempered martensitic microstructure. The inner surface of the RPV is weld-cladded with stainless steels to prevent corrosion. The goal of this study is to evaluate the microstructural properties of the clad interface between Ni-Cr-Mo low alloy steel and stainless weldment, and the effects of post weld heat treatment (PWHT) on the properties. The properties of the clad interface were compared with those of commercial Mn-Mo-Ni low alloy steel. Multi-layer welding of model alloys with ER308L and ER309L stainless steel by the SAW method was performed, and then PWHT was conducted at 610°C for 30 h. The microstructural changes of the clad interface were analyzed using OM, SEM and TEM, and micro-Vickers hardness tests were performed. Before PWHT, the heat affected zone (HAZ) showed higher hardness than base and weld metals due to formation of martensite after welding in both steels. In addition, the hardness of the HAZ in Ni-Cr-Mo low alloy steel was higher than that in Mn-Mo-Ni low alloy steel due to a comparatively high martensite fraction. The hardness of the HAZ decreased after PWHT in both steels, but the dark region was formed near the fusion line in which the hardness was locally high. In the case of Mn-Mo-Ni low alloy steel, formation of fine Cr-carbides in the weld region near the fusion line by diffusion of C from the base metal resulted in locally high hardness in the dark region. However, the precipitates of the region in the Ni-Cr-Mo low alloy steel were similar to that in the base metal, and the hardness in the region was not greatly different from that in the base metal.

Do minimum wages improve early life health? Evidence from developing countries.

Science.gov (United States)

Majid, Muhammad Farhan; Mendoza Rodríguez, José M; Harper, Sam; Frank, John; Nandi, Arijit

2016-06-01

The impact of legislated minimum wages on the early-life health of children living in low and middle-income countries has not been examined. For our analyses, we used data from the Demographic and Household Surveys (DHS) from 57 countries conducted between 1999 and 2013. Our analyses focus on height-for-age z scores (HAZ) for children under 5 years of age who were surveyed as part of the DHS. To identify the causal effect of minimum wages, we utilized plausibly exogenous variation in the legislated minimum wages during each child's year of birth, the identifying assumption being that mothers do not time their births around changes in the minimum wage. As a sensitivity exercise, we also made within family comparisons (mother fixed effect models). Our final analysis on 49 countries reveal that a 1% increase in minimum wages was associated with 0.1% (95% CI = -0.2, 0) decrease in HAZ scores. Adverse effects of an increase in the minimum wage were observed among girls and for children of fathers who were less than 35 years old, mothers aged 20-29, parents who were married, parents who were less educated, and parents involved in manual work. We also explored heterogeneity by region and GDP per capita at baseline (1999). Adverse effects were concentrated in lower-income countries and were most pronounced in South Asia. By contrast, increases in the minimum wage improved children's HAZ in Latin America, and among children of parents working in a skilled sector. Our findings are inconsistent with the hypothesis that increases in the minimum wage unconditionally improve child health in lower-income countries, and highlight heterogeneity in the impact of minimum wages around the globe. Future work should involve country and occupation specific studies which can explore not only different outcomes such as infant mortality rates, but also explore the role of parental investments in shaping these effects. Copyright © 2016 Elsevier Ltd. All rights reserved.

Optimización multiobjetivo del proceso de soldeo GMAW de la aleación AA 6063-T5 basado en la penetración y en la zona afectada térmicamente

Directory of Open Access Journals (Sweden)

Miguel, Valentín

2015-03-01

Full Text Available The selection of technological parameters in a welding process must be led to the optimized results of the operation. Penetration is one of the most decisive factors for the success of the joint. Another important factor is the Heat Affected Zone (HAZ, when the mechanical properties of this one are modified respecting to the base material. The way in which the technological variables of the process affects to both them, penetration and HAZ, are inverse in each case. This work presents an optimization methodology based on the Design of Experiments (DOE and the Response Surface Method (RSM of the GMAW process applied to the aluminum alloy AA 6063-T5. This research is focused to obtain penetration rates that make HAZ values to be suitable in current applications. Welding rate has been found to be the most significant technological parameter for controlling the process.La selección de los parámetros tecnológicos que regulan los procesos de soldadura por arco debe efectuarse de forma que se optimice el resultado de la operación. La penetración es uno de los factores decisivos, ya que es determinante en el modo de ejecutar el proceso así como en el comportamiento de la unión. Otro factor importante es la Zona Afectada Térmicamente (ZAT, cuando ésta presenta propiedades diferentes a las del material base. El modo en que afectan los parámetros tecnológicos en ambos, penetración y ZAT, es inverso a los objetivos que suelen plantearse. En este trabajo se presenta una metodología de optimización del proceso GMAW de la aleación AA 6063-T5 basado en el diseño de experimentos y la superficie de respuesta. Los resultados obtenidos permiten evaluar la conveniencia de fijar como objetivo valores de penetración tendentes a mantener ZAT en ratios asumibles. Se obtiene que la variable que más afecta a la optimización es la velocidad de soldadura.

Microstructure and dynamic tensile behavior of DP600 dual phase steel joint by laser welding

Energy Technology Data Exchange (ETDEWEB)

Dong, Danyang, E-mail: dongdanyang@mail.neu.edu.cn [College of Science, Northeastern University, No. 11, Lane 3, WenHua Road, HePing District, Shenyang 110819 (China); Liu, Yang, E-mail: liuyang@mail.neu.edu.cn [Key Laboratory for Anisotropy and Texture of Materials, Ministry of Education, Northeastern University, Shenyang 110819 (China); Yang, Yuling, E-mail: yulingyang@mail.neu.edu.cn [College of Science, Northeastern University, No. 11, Lane 3, WenHua Road, HePing District, Shenyang 110819 (China); Li, Jinfeng, E-mail: lijinfengboda@163.com [College of Science, Northeastern University, No. 11, Lane 3, WenHua Road, HePing District, Shenyang 110819 (China); Ma, Min, E-mail: sharon6789@163.com [College of Science, Northeastern University, No. 11, Lane 3, WenHua Road, HePing District, Shenyang 110819 (China); Jiang, Tao, E-mail: tao.jiang906@yahoo.com [College of Science, Northeastern University, No. 11, Lane 3, WenHua Road, HePing District, Shenyang 110819 (China)

2014-01-31

Dual phase (DP) steels have been widely used in the automotive industry to reduce vehicle weight and improve car safety. In such applications welding and joining have to be involved, which would lead to a localized change of the microstructure and property, and create potential safety and reliable issues under dynamic loading. The aim of the present study is to examine the rate-dependent mechanical properties, deformation and fracture behavior of DP600 steel and its welded joint (WJ) produced by Nd:YAG laser welding over a wide range of strain rates (0.001–1133 s{sup −1}). Laser welding results in not only significant microhardness increase in the fusion zone (FZ) and inner heat-affected zone (HAZ), but also the formation of a softened zone in the outer HAZ. The yield strength (YS) of the DP600 steel increases and the ultimate tensile strength (UTS) remains almost unchanged, but the ductility decreases after welding. The DP600 base metal (BM) and WJ are of positive strain rate sensitivity and show similar stress–strain response at all studied strain rates. The enhanced ductility at strain rates ranging from 1 to 100 s{sup −1} is attributed to the retardation of the propagation of plastic strain localization due to the positive strain rate sensitivity and the thermal softening caused by deformation induced adiabatic temperature rise during dynamic tensile deformation. The tensile failure occurs in the inner HAZ of the joint and the distance of failure location from the weld centerline decreases with increasing strain rate. The mechanism for the changing failure location can be related to the different strain rate dependence of the plastic deformation behavior of the microstructures in various regions across the joint. The DP600 WJ absorbs more energy over the whole measured strain rates than that of the BM due to the higher strength at the same strain when the deformation only up to 10% is considered.

Evolution of the biochemical profile of children treated or undergoing treatment for moderate or severe stunting: consequences of metabolic programming?

Directory of Open Access Journals (Sweden)

Jullyana F.R. Alves

2014-07-01

Full Text Available OBJECTIVE: to evaluate changes in the biochemical profile of children treated or being treated for moderate or severe stunting in a nutrition recovery and education center. METHODS: this was a retrospective longitudinal study of 263 children treated at this center between August of 2008 to August of 2011, aged 1 to 6 years, diagnosed with moderate (z-score of height-for-age [HAZ] < -2 or severe stunting (HAZ < -3. Data were collected on socioeconomic conditions, dietary habits, and biochemical changes, as well as height according to age. RESULTS: the nutritional intervention showed an increase in HAZ of children with moderate (0.51 ± 0.4, p = 0.001 and severe (0.91 ± 0.7, p = 0.001 stunting during the monitoring. Increased levels of insulin-like growth factor 1 (IGF-1 (initial: 71.7 ng/dL; final: 90.4 ng/dL; p = 0.01 were also observed, as well as a reduction in triglycerides (TG in both severely (initial: 91.8 mg/dL; final: 79.1 mg/dL; p = 0.01 and in moderately malnourished children (initial: 109.2 mg/dL; final 88.7 mg/dL; p = 0.01, and a significant increase in high-density lipoprotein cholesterol HDL-C only in the third year of intervention (initial: 31.4 mg/dL; final: 42.2 mg/dL. The values of total cholesterol (TC and low-density lipoprotein cholesterol (LDL-C levels remained high throughout the treatment (initial: 165.1 mg/dL; final: 163.5 mg/dL and initial: 109.0 mg/dL; final: 107.3 mg/dL, respectively. CONCLUSION: the nutritional treatment for children with short stature was effective in reducing stunting and improving TG and HDL-C after three years of intervention. However, the levels of LDL-C and TC remained high even in treated children. It is therefore speculated that these changes may result from metabolic programming due to malnutrition.

Carotid intima-media thickness at age 30, birth weight, accelerated growth during infancy and breastfeeding: a birth cohort study in Southern Brazil.

Science.gov (United States)

Linhares, Rogério da Silva; Gigante, Denise Petrucci; de Barros, Fernando Celso Lopes Fernandes; Horta, Bernardo Lessa

2015-01-01

To examine the relationship between carotid intima-media thickness (IMT) at age 30 and birth characteristics, growth during infancy, and breastfeeding duration, among subjects who have been prospectively followed since birth. In 1982, all births in the city of Pelotas, southern Brazil, were identified and those children (n = 5,914) whose families lived in the urban area of the city have been followed and evaluated at several time points. The cohort participants were evaluated in 2012-13, and IMT was measured at the posterior wall of the right and left common carotid arteries in longitudinal planes using ultrasound imaging. We obtained valid IMT measurements for 3,188 individuals. Weight-for-age z-score (WAZ) at age 2 years, weight-for-height z-score (WHZ) at age 4, height-for-age z-score (HAZ) at 4 years, WAZ at age 4 and relative conditional weight at 4 years were positively associated with IMT, even after controlling for confounding variables. The beta-coefficient associated with ≥ 1 s.d. WAZ at age 2 (compared to those with a <-1 s.d.) was 3.62 μm (95% CI 0.86 to 6.38). The beta-coefficient associated with ≥ 1 s.d. WHZ at 4 (in relation to <-1 s.d) was 3.83 μm (95% CI 0.24 to 7.42). For HAZ at 4, the beta-coefficient for ≥ 1 s.d. in relation to <-1 s.d. was 4.19 μm (95% CI 1.14 to 7.25). For WAZ at 4, the beta-coefficient associated with ≥ 1 s.d. in relation to <-1 s.d. was 4.28 μm (95% CI 1.59 to 6.97). The beta-coefficient associated with conditional weight gain at age 2-4 was 1.26 μm (95% CI 0.49 to 2.02). IMT at age 30 was positively associated with WAZ at age 2 years, WHZ at age 4, HAZ at age 4, WAZ at age 4 and conditional weight gain at age 4 years.

Microstructural Characterization of Clad Interface in Welds of Ni-Cr-Mo High Strength Low Alloy Steel

International Nuclear Information System (INIS)

Kim, Hong-Eun; Kim, Min-Chul; Lee, Ho-Jin; Kim, Keong-Ho; Lee, Ki-Hyoung; Lee, Chang-Hee

2011-01-01

SA508 Gr.4N Ni-Cr-Mo low alloy steel, in which Ni and Cr contents are higher than in commercial SA508 Gr.3 Mn-Mo-Ni low alloy steels, may be a candidate reactor pressure vessel (RPV) material with higher strength and toughness from its tempered martensitic microstructure. The inner surface of the RPV is weld-cladded with stainless steels to prevent corrosion. The goal of this study is to evaluate the microstructural properties of the clad interface between Ni-Cr-Mo low alloy steel and stainless weldment, and the effects of post weld heat treatment (PWHT) on the properties. The properties of the clad interface were compared with those of commercial Mn-Mo-Ni low alloy steel. Multi-layer welding of model alloys with ER308L and ER309L stainless steel by the SAW method was performed, and then PWHT was conducted at 610°C for 30 h. The microstructural changes of the clad interface were analyzed using OM, SEM and TEM, and micro-Vickers hardness tests were performed. Before PWHT, the heat affected zone (HAZ) showed higher hardness than base and weld metals due to formation of martensite after welding in both steels. In addition, the hardness of the HAZ in Ni-Cr-Mo low alloy steel was higher than that in Mn-Mo-Ni low alloy steel due to a comparatively high martensite fraction. The hardness of the HAZ decreased after PWHT in both steels, but the dark region was formed near the fusion line in which the hardness was locally high. In the case of Mn-Mo-Ni low alloy steel, formation of fine Cr-carbides in the weld region near the fusion line by diffusion of C from the base metal resulted in locally high hardness in the dark region. However, the precipitates of the region in the Ni-Cr-Mo low alloy steel were similar to that in the base metal, and the hardness in the region was not greatly different from that in the base metal.

Household food group expenditure patterns are associated with child anthropometry at ages 5, 8 and 12 years in Ethiopia, India, Peru and Vietnam.

Science.gov (United States)

Humphries, Debbie L; Dearden, Kirk A; Crookston, Benjamin T; Woldehanna, Tassew; Penny, Mary E; Behrman, Jere R

2017-08-01

Population-level analysis of dietary influences on nutritional status is challenging in part due to limitations in dietary intake data. Household expenditure surveys, covering recent household expenditures and including key food groups, are routinely conducted in low- and middle-income countries. These data may help identify patterns of food expenditure that relate to child growth. We investigated the relationship between household food expenditures and child growth using factor analysis. We used data on 6993 children from Ethiopia, India, Peru and Vietnam at ages 5, 8 and 12y from the Young Lives cohort. We compared associations between household food expenditures and child growth (height-for-age z scores, HAZ; body mass index-for-age z scores, BMI-Z) using total household food expenditures and the "household food group expenditure index" (HFGEI) extracted from household expenditures with factor analysis on the seven food groups in the child dietary diversity scale, controlling for total food expenditures, child dietary diversity, data collection round, rural/urban residence and child sex. We used the HFGEI to capture households' allocations of their finances across food groups in the context of local food pricing, availability and pReferences RESULTS: The HFGEI was associated with significant increases in child HAZ in Ethiopia (0.07), India (0.14), and Vietnam (0.07) after adjusting for all control variables. Total food expenditures remained significantly associated with increases in BMI-Z for India (0.15), Peru (0.11) and Vietnam (0.06) after adjusting for study round, HFGEI, dietary diversity, rural residence, and whether the child was female. Dietary diversity was inversely associated with BMI-Z in India and Peru. Mean dietary diversity increased from age 5y to 8y and decreased from age 8y to 12y in all countries. Household food expenditure data provide insights into household food purchasing patterns that significantly predict HAZ and BMI-Z. Including food

Borosonic inspection and remaining useful operational life estimation of steam turbine rotors; Inspeccion borosonica y estimacion de vida remanente de rotores de turbinas de vapor

Energy Technology Data Exchange (ETDEWEB)

Carnero P, Jose A; Dorantes G, Oscar; Munoz Q, Rodolfo; Serrano R, Luis E. [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)

2004-07-01

The turbo-generators used in the electric power generation frequently go through transitory operations (start ups, shut downs or power changes). Such actions cause that certain critical components of the turbines, such as rotors and casings, are put under cycles of repetitive stresses, which consume its useful life. The frequency whereupon these transitory thermal cycles happen result in the presence of high thermo-mechanical stresses that produce fatigue (damage) in the rotor material. With time, at the increase of the material fatigue, fissures form that can inclusively lead to severe, catastrophic faults. The borosonic inspection consists in introducing and positioning an automatic probe in the central drill of the rotor, this allows the non-destructive inspection with longitudinal ultrasonic beam, ultrasonic cross-sectional and ultrasonic superficial. This way, it is possible to detect and locate geometric discontinuities (superficial and volumetric), in at least 100 mm of depth from the drill surface in its entire periphery and throughout the rotor length. [Spanish] Los turbogeneradores empleados en la generacion de energia electrica con frecuencia realizan operaciones transitorias (arranques, paros o cambios de potencia). Acciones tales, provocan que ciertos componentes criticos de las turbinas, como los rotores y carcasas, sean sometidos a ciclos de esfuerzos repetitivos, lo que consume su vida util. La frecuencia con que ocurren estos ciclos termicos transitorios da como resultado la presencia de altos esfuerzos termomecanicos que producen una fatiga (dano) en el material del rotor. Con el tiempo, al incrementarse la fatiga del material, se forman fisuras que pueden conducir a fallas severas, catastroficas inclusive. La inspeccion borosonica consiste en introducir y posicionar una sonda automatica en el barreno central del rotor, ello permite la inspeccion no destructiva con haz ultrasonico longitudinal, haz ultrasonico transversal y haz ultrasonico

Evolution of the biochemical profile of children treated or undergoing treatment for moderate or severe stunting: consequences of metabolic programming?

Science.gov (United States)

Alves, Jullyana F R; Britto, Revilane P A; Ferreira, Haroldo S; Sawaya, Ana L; Florêncio, Telma M M T

2014-01-01

to evaluate changes in the biochemical profile of children treated or being treated for moderate or severe stunting in a nutrition recovery and education center. this was a retrospective longitudinal study of 263 children treated at this center between August of 2008 to August of 2011, aged 1 to 6 years, diagnosed with moderate (z-score of height-for-age [HAZ] < -2) or severe stunting (HAZ < -3). Data were collected on socioeconomic conditions, dietary habits, and biochemical changes, as well as height according to age. the nutritional intervention showed an increase in HAZ of children with moderate (0.51 ± 0.4, p = 0.001) and severe (0.91 ± 0.7, p = 0.001) stunting during the monitoring. Increased levels of insulin-like growth factor 1 (IGF-1) (initial: 71.7 ng/dL; final: 90.4 ng/dL; p = 0.01) were also observed, as well as a reduction in triglycerides (TG) in both severely (initial: 91.8mg/dL; final: 79.1mg/dL; p = 0.01) and in moderately malnourished children (initial: 109.2mg/dL; final 88.7mg/dL; p = 0.01), and a significant increase in high-density lipoprotein cholesterol HDL-C only in the third year of intervention (initial: 31.4mg/dL; final: 42.2mg/dL). The values of total cholesterol (TC) and low-density lipoprotein cholesterol (LDL-C) levels remained high throughout the treatment (initial: 165.1mg/dL; final: 163.5mg/dL and initial: 109.0mg/dL; final: 107.3mg/dL, respectively). the nutritional treatment for children with short stature was effective in reducing stunting and improving TG and HDL-C after three years of intervention. However, the levels of LDL-C and TC remained high even in treated children. It is therefore speculated that these changes may result from metabolic programming due to malnutrition. Copyright © 2014 Sociedade Brasileira de Pediatria. Published by Elsevier Editora Ltda. All rights reserved.

Irradiation effects on weld heat-affected zone and plate materials (series 11)

International Nuclear Information System (INIS)

Nanstad, R.K.; McCabe, D.E.

1995-01-01

The purpose of this task is to examine the effects of neutron irradiation on the fracture toughness (ductile and brittle) of the HAZ of welds and of A 302 grade B (A302B) plate materials typical of those used fabricating older RPVs. The initial plate material of emphasis will be A302B steel, not the A302B modified with nickel additions. This decision was made by the NRC following a survey of the materials of construction for RPBs in operating U.S. nuclear plants. Reference 1 was used for the preliminary survey, and the information from that report was revised by NRC staff based on information contained in the licensee responses to Generic Letter (GL) 92-01, open-quotes Reactor Vessel Structural Integrity, 10CFR50.54(f).close quotes The resulting survey showed a total of eight RPVs with A302B, ten with A302B (modified), and one with A302 grade A plate. Table 5.1 in the previous semiannual report provides a summary of that survey. For the HAZ portion of the program, the intent is to examine HAZ material in the A302B (i.e., with low nickel content) and in A302B (modified) or A533B-1 (i.e., with medium nickel content). During this reporting period, two specific plates were identified as being applicable to this task. One plate is A302B and the other is A302B (modified). The A302B plate (43 x 42 x 7 in.) will be prepared for welding, while the A302B (modified) plate already contains a commercially produced weld (heat 33A277, Linde 0091 flux). These plates were identified from a list of ten materials provided by Mr. E. Biemiller of Yankee Atomic Electric Company (YAEC). The materials have been requested from YAEC for use in this irradiation task, and arrangements are being made with YAEC for procurement of the plates mentioned above

Study of sulphate-reducing bacteria corrosion in the weld joint for API X-70 steel

Directory of Open Access Journals (Sweden)

Flores, J. E.

2012-10-01

Full Text Available The corrosion behavior originated by sulfate-reducing bacteria (SRB was studied in two regions of welded API X-70 steel pipeline. The studies were focused on base material (BM and heat affected zone (HAZ, from the internal region of the pipe. SRB were extracted from oil and grown in a Postgate medium. Corrosion was evaluated at 60 °C for times between 5 and 64 days. Potentiodynamic polarization curves, obtained by electrochemical techniques, indicated surface activation at short times. Structural and morphological characterizations were carried out by scanning electron microscopy (SEM and optical microscopy (OM. H₂S concentration and pH were also measured. Results showed an important increase in the corrosion damage up to 20 days, influenced by the SRB activity, which lead to a maximum of H₂S (pH minimum. It was found a localized corrosion attack in the HAZ in a higher quantity compared to BM; and the formation of a thin film on the steel surface, originated by corrosion products and bacterial activity.

El comportamiento ante la corrosión, originada por bacterias sulfato-reductoras (SRB, fue estudiado en dos regiones de un tubo de acero soldado API X-70. Los estudios se enfocaron en el material base (BM y la zona afectada térmicamente (HAZ, en la parte interna del tubo. Las SRB fueron extraídas del petróleo y cultivadas en un medio Postgate. El comportamiento a la corrosión fue evaluado a una temperatura de 60 °C, por periodos comprendidos entre 5 y 64 días. El análisis de las curvas de polarización potenciodinámicas, obtenidas por técnicas electroquímicas, indicó la activación de la superficie para tiempos cortos. La superficie fue caracterizada estructural y morfológicamente mediante microscopia electrónica de barrido (SEM, así como mediante microscopía óptica (OM. La concentración de H₂S y el pH también fueron medidos. Los resultados mostraron un aumento importante de la corrosi

Failure of Stainless Steel Welds Due to Microstructural Damage Prevented by In Situ Metallography

OpenAIRE

Lopez,Juan Manuel Salgado; Alvarado,María Inés; Hernandez,Hector Vergara; Quiroz,José Trinidad Perez; Olmos,Luis

2016-01-01

Abstract In stainless steels, microstructural damage is caused by precipitation of chromium carbides or sigma phase. These microconstituents are detrimental in stainless steel welds because they lead to weld decay. Nevertheless, they are prone to appear in the heat affected zone (HAZ) microstructure of stainless steel welds. This is particularly important for repairs of industrial components made of austenitic stainless steel. Non-destructive metallography can be applied in welding repairs of...

Some current engineering topics in nuclear power plant components

International Nuclear Information System (INIS)

Amana, M.

1977-01-01

An analysis based on the principle of fracture mechanics, is presented for several engineering problems occuring in nuclear power plant components. The specific problems covered are: underclad cracking; stress corrosion cracking; cracks in HAZ of nozzle weld; feedwater nozzle corner crack; shift of transition temperature due to neutron irradiation; LWR local-ECC thermal shock experiment; and design and material selection of RPV in terms of fracture mechanics. (B.R.H.)

Comparative evaluation of cyclic strength of welded joints of titanium alloys

International Nuclear Information System (INIS)

Grigor'yants, A.G.; Florinskij, Yu.B.; Moryakov, V.F.; Kvasha, Yu.N.

1983-01-01

Results of comparative study of cyclic strength of titanium alloy PT-3V, fused by three ways of welding, are presented. It is established that the use of laser welding promotes the formation of favourable structure of weld metal and HAZ (heat affected zone), characterized by the formation of dislocation barriers. The results obtained permit to recommend laser technique instead of traditional ways of welding during product manufacturing of titanium allo

Transient elastography for predicting liver-related events in cirrhotic HIV-infected patients

OpenAIRE

Montes-Ramírez, M. L.; Berenguer, Juan; Miró, J. M.; Quereda, Carmen; Hernando Jeréz, María Asunción; Sanz, J.; Ortega, E.; Tural, Cristina; Wichmann, M. A.; Zamora, F. X.; González García, J. J.

2017-01-01

We assessed liver stiffness measurement (LSM) for the prediction of mortality and decompensation in HIVinfected patients with compensated liver cirrhosis. A prospective cohort study of HIV-infected patients with confirmed liver cirrhosis from 9 hospitals in Spain. LSM was undertaken for each patient; clinical events were collected prospectively after the baseline visit, and patients were followed until death or the censoring date. We used univariate/multivariate Cox proportional haz...

Initial Testing for the Recommendation of Improved Gas Metal Arc Welding Procedures for HY-80 Steel Plate Butt Joints at Norfolk Naval Shipyard

Science.gov (United States)

2015-12-01

17  Figure 11.  IRMS versus VRMS Comparison with Different Ar/CO2 Gas Mixtures Using GMAW-P...21  Figure 13.  IRMS versus VRMS Comparison with Miller and Lincoln Welding Machines in the Horizontal and Vertical Positions Using GMAW-P...Gas Metal Arc Welding Pulsed Spray Transfer GMAW-S Gas Metal Arc Welding Spray Transfer HAZ Heat Affected Zone HC#1 Hull Cut #1 IRMS Current Root

Experimental and Modeling Study of Liquid-Assisted—Laser Beam Micromachining of Smart Ceramic Materials

Directory of Open Access Journals (Sweden)

Mayur Parmar

2018-05-01

Full Text Available Smart ceramic materials are next generation materials with the inherent intelligence to adapt to change in the external environment. These materials are destined to play an essential role in several critical engineering applications. Machining these materials using traditional machining processes is a challenge. The laser beam micromachining (LBMM process has the potential to machine such smart materials. However, laser machining when performed in air induces high thermal stress on the surface, often leading to crack formation, recast and re-deposition of ablated material, and large heat-affected zones (HAZ. Performing laser beam machining in the presence of a liquid medium could potentially resolve these issues. This research investigates the possibility of using a Liquid Assisted—Laser Beam Micromachining (LA-LBMM process for micromachining smart ceramic materials. Experimental studies are performed to compare the machining quality of laser beam machining process in air and in a liquid medium. The study reveals that the presence of liquid medium helps in controlling the heat-affected zone and the taper angle of the cavity drilled, thereby enhancing the machining quality. Analytical modeling is developed for the prediction of HAZ and cavity diameter both in air and underwater conditions, and the model is capable of predicting the experimental results to within 10% error.

Microstructure and mechanical properties of resistance-spot-welded joints for A5052 aluminum alloy and DP 600 steel

Energy Technology Data Exchange (ETDEWEB)

Chen, Jianbin [College of Automotive Collaborative Innovation Center, Chongqing University, No. 174, Shazheng Street, Shapingba District, Chongqing 400044 (China); Yuan, Xinjian, E-mail: xinjianyuan@yahoo.com [College of Materials Science and Engineering, Chongqing University, No. 174, Shazheng Street, Shapingba District, Chongqing 400044 (China); Hu, Zhan; Sun, Changzheng; Zhang, Yanxin; Zhang, Yuxuan [College of Materials Science and Engineering, Chongqing University, No. 174, Shazheng Street, Shapingba District, Chongqing 400044 (China)

2016-10-15

The microstructure and mechanical properties of resistance-spot-welded A5052 aluminum alloy and DP 600 dual-phase steel joint were studied. The fusion zone (FZ) and heat-affected zone (HAZ) of DP 600 exhibited lath martensite and ferrite-martensite structures, respectively. The microstructure of FZ and HAZ in the A5052 side was composed of cellular crystals and the boundary region of FZ exhibited a columnar crystal morphology. A Fe{sub 2}Al{sub 5} intermetallic compound (IMC) layer with 3.3 μm thickness was found adjacent to the DP 600 side, whereas a needle-shaped Fe{sub 4}Al{sub 13} IMC layer with length of 0.67 μm to 15.8 μm was found adjacent to the aluminum alloy side. The maximum tensile shear load of the A5052/DP 600 joint was 5.5 KN, with a corresponding molten nugget diameter of 6.3 mm. The fracture morphology of the optimized A5052/DP 600 joint was mainly an elongated dimple fracture accompanied by cleavage fracture. - Highlights: •A5052 and DP 600 with large gaps in properties were investigated by RSW. •The microstructures of RSW joints in DP 600/A5052 were examined detailedly. •The micro/macro-characteristics and strength relations of joints were analyzed.

Microstructural characterization of welded zone for Fe{sub 3}Al/Q235 fusion-bonded joint

Energy Technology Data Exchange (ETDEWEB)

Ma Haijun [Key Lab of Liquid Structure and Heredity of Materials, Ministry of Education, Shandong University, Jinan 250061, Shandong Province, Jing Shi Road 73, Shandong (China)], E-mail: hjma123@mail.sdu.edu.cn; Li Yajiang [Key Lab of Liquid Structure and Heredity of Materials, Ministry of Education, Shandong University, Jinan 250061, Shandong Province, Jing Shi Road 73, Shandong (China); Material Science Department, Bauman Moscow State Technical University, Moscow 105005 (Russian Federation); Puchkov, U.A. [Material Science Department, Bauman Moscow State Technical University, Moscow 105005 (Russian Federation); Wang Juan [Key Lab of Liquid Structure and Heredity of Materials, Ministry of Education, Shandong University, Jinan 250061, Shandong Province, Jing Shi Road 73, Shandong (China)

2008-12-20

The microstructural characterization of Fe{sub 3}Al/Q235 welded zone were analysed to investigate the welding behavior of Fe{sub 3}Al intermetallic. The results indicated that a crack-free Fe{sub 3}Al/Q235 joint was obtained when Cr25-Ni13 alloy was adopted as the filler metal. The microstructure of the welded zone presented different morphology due to the severe fluctuation of Al, Ni, Mn and Cr elements near the fusion zone. The fish-bone like structures in Q235 side fusion zone were composed of {alpha}-Fe(Cr, Al, Ni) solid solutions. Fe{sub 3}Al/Q235 joint fractured in the Fe{sub 3}Al HAZ, and shear strength of 533.33 MPa was achieved. The fracture mode of Fe{sub 3}Al side fracture surface was mainly transgranular cleavage, occured along [1 1 1] orientation on {l_brace}1 1 0{r_brace} planes. And the Q235 side fracture surface was in intergranular and quasi-cleavage mode. The phase relations of {gamma} and {alpha} in Fe{sub 3}Al side fusion zone, constituent of lower bainite in the weld and the Fe{sub 3}Al ordered transformation in HAZ were also determined.

Stress Analysis of Single Spacer Grid Support considering Fuel Rod

Energy Technology Data Exchange (ETDEWEB)

Yoo, Y. G.; Jung, D. H.; Kim, J. H. [Chungnam National University, Daejeon (Korea, Republic of); Park, J. K.; Jeon, K. L. [Korea Nuclear Fuel, Daejeon (Korea, Republic of)

2010-10-15

Pressurized water reactor (PWR) nuclear fuel assembly is mainly composed of a top-end piece, a bottom-end piece, lots of fuel rods, and several spacer grids. Among them, the main function of spacer grid is protecting fuel rods from Fluid Induced Vibration (FIV). The cross section of spacer grid assembled by laser welding in upper and lower point. When the fuel rod inserted in spacer gird, spring and dimple and around of welded area got a stresses. The main hypothesis of this analysis is the boundary area of HAZ and base metal can get a lot of damage than other area by FIV. So, design factors of spacer grid mainly considered to preventing the fatigue failure in HAZ and spring and dimple of spacer grid. From previous researching, the environment in reactor verified. Pressure and temperature of light water observed 15MPa and 320 .deg. C, and vibration of the fuel rod observed within 0 {approx} 50Hz. In this study, mechanical properties of zirconium alloy that extracted from the test and the spacer grid model which used in the PWR were applied in stress analyzing. General-purpose finite element analysis program was used ANSYS Workbench 12.0.1 version. 3-D CAD program CATIA was used to create spacer grid model

Characterization of Flame Cut Heavy Steel: Modeling of Temperature History and Residual Stress Formation

Science.gov (United States)

Jokiaho, T.; Laitinen, A.; Santa-aho, S.; Isakov, M.; Peura, P.; Saarinen, T.; Lehtovaara, A.; Vippola, M.

2017-12-01

Heavy steel plates are used in demanding applications that require both high strength and hardness. An important step in the production of such components is cutting the plates with a cost-effective thermal cutting method such as flame cutting. Flame cutting is performed with a controlled flame and oxygen jet, which burns the steel and forms a cutting edge. However, the thermal cutting of heavy steel plates causes several problems. A heat-affected zone (HAZ) is generated at the cut edge due to the steep temperature gradient. Consequently, volume changes, hardness variations, and microstructural changes occur in the HAZ. In addition, residual stresses are formed at the cut edge during the process. In the worst case, unsuitable flame cutting practices generate cracks at the cut edge. The flame cutting of thick steel plate was modeled using the commercial finite element software ABAQUS. The results of modeling were verified by X-ray diffraction-based residual stress measurements and microstructural analysis. The model provides several outcomes, such as obtaining more information related to the formation of residual stresses and the temperature history during the flame cutting process. In addition, an extensive series of flame cut samples was designed with the assistance of the model.

Evaluation of efficacy of entomopathogenic nematodes against larvae of Lucilia sericata (Meigen, 1826) (Diptera: Calliphoridae).

Science.gov (United States)

Tóth, Erika M; Márialigeti, K; Fodor, A; Lucskai, A; Farkas, R

2005-01-01

The blowfly Lucilia sericata (Meigen, 1826) (Diptera: Calliphoridae) is the primary agent of cutaneous myiasis of sheep in northern Europe, southern Africa, Australia and New Zealand. As the application of chemicals has several disadvantages, alternative control measures of traumatic myiasis of livestock must be developed. In this study, the use of entomopathogenic nematodes (EPNs) as potential biocontrol agents against second instar larvae of Lucilia sericata was considered. The following nematode species were tested: Heterorhabditis bacteriophora (IS 5, HHU 1, Hmol, HNC 1, HAZ 36, Hbrecon, HHU 2, HAZ 29, HHP 88, HHU 3, HHU 4 and HGua), Steinernema intermedia, NC513 strain of S. glaserii, S. anomali, S. riobrave, Steinernema sp. and 5 strains of S. feltiae (22, Vija Norway, HU 1, scp, and IS 6). None of the examined EPN species or strains showed larvicidal efficacy at 37 degrees C (no killing effect was observed in the case of the two heat-tolerant strains--H. bacteriophora and S.feltiae) against L. sericata larvae. At lower temperatures (20 degrees C and 25 degrees C) only strains of S. feltiae were found to be active. The overall odds ratios calculated for L. sericata maggots to contract S. feltiae nematode infection show significant (p nematode occurred in the cadavers.

Experimental and numerical simulation of thermomechanical phenomena during a TIG welding process

International Nuclear Information System (INIS)

Depradeux, L.; Julien, J.F.

2004-01-01

In this study, a parallel experimental and numerical simulation of phenomena that take place in the Heat Affected Zone (HAZ) during TIG welding on 316L stainless steel is presented. The aim of this study is to predict by numerical simulation residual stresses and distortions generated by the welding process. For the experiment, a very simple geometry with reduced dimensions is considered: the specimens are disks, made of 316L. The discs are heated in the central zone in order to reproduce thermo-mechanical cycles that take place in the HAZ during a TIG welding process. During and after thermal cycle, a large quantity of measurement is provided, and allows to compare the results of different numerical models used in the simulations. The comparative thermal and mechanical analysis allows to assess the general ability of the numerical models to describe the structural behavior. The importance of the heat input rate and material characteristics is also investigated. When a melted zone is created, the thermal simulation reproduce well the temperature field in the upper face of the disk, but the size of the weld pool is not correctly rated, as fluid flows are not taken into account. Despite this fact, the general structural behavior is well represented by simulation

The Optimization of Process Parameters and Microstructural Characterization of Fiber Laser Welded Dissimilar HSLA and MART Steel Joints

Directory of Open Access Journals (Sweden)

Celalettin Yuce

2016-10-01

Full Text Available Nowadays, environmental impact, safety and fuel efficiency are fundamental issues for the automotive industry. These objectives are met by using a combination of different types of steels in the auto bodies. Therefore, it is important to have an understanding of how dissimilar materials behave when they are welded. This paper presents the process parameters’ optimization procedure of fiber laser welded dissimilar high strength low alloy (HSLA and martensitic steel (MART steel using a Taguchi approach. The influence of laser power, welding speed and focal position on the mechanical and microstructural properties of the joints was determined. The optimum parameters for the maximum tensile load-minimum heat input were predicted, and the individual significance of parameters on the response was evaluated by ANOVA results. The optimum levels of the process parameters were defined. Furthermore, microstructural examination and microhardness measurements of the selected welds were conducted. The samples of the dissimilar joints showed a remarkable microstructural change from nearly fully martensitic in the weld bead to the unchanged microstructure in the base metals. The heat affected zone (HAZ region of joints was divided into five subzones. The fusion zone resulted in an important hardness increase, but the formation of a soft zone in the HAZ region.

MOLEKÜLER CIMBIZLAMAYA DAYALI YENİ BİR BISFENOL-BIPHENANTHROLINE SENTEZİ

Directory of Open Access Journals (Sweden)

Said nadeem

2015-11-01

Full Text Available 1,10-fenantrolin’den elde edilen "dugdugi" 8 molekülü sentezlendi ve NMR, EIMS ve UV kullanılarak yapısı aydınlatıldı. Bisfenol 8’I elde etmek için 1,3dibrompropan kullanılarak alkillendi ve 4-(1H-imidazo[4,5-f][1,10]phenanthrolin-2-ylphenol ile reaksiyona sokuldu. Molekül 8’in 30 molL-1 çözeltisi %10 DMF içeren etanolde hazırlandı, ve etanol ile hazırlanmış 30 m L-1 Co2+, Cr3+, Cu2+, Fe3+, Mn2+, Ni2+, Ag+, and Zn2+ çözeltisi ile 30 dakika karıştırıldı.Kemosensör 8, Fe3+ varlığında pembe renk vererek çalışırken, diğer metallerin varlığında ayırt edici bir renk gözlenmedi. "Dugdugi" nin moleküler UV spektrumunda 279 nm’de bulunan pik Fe3+ ile etkileştirilince 290 nm’ye kaydı. Ayrıca, 524 nm’de yeni bir pik oluştuğu görüldü

Microhardness and Stress Analysis of Laser-Cladded AISI 420 Martensitic Stainless Steel

Science.gov (United States)

Alam, Mohammad K.; Edrisy, Afsaneh; Urbanic, Jill; Pineault, James

2017-03-01

Laser cladding is a surface treatment process which is starting to be employed as a novel additive manufacturing. Rapid cooling during the non-equilibrium solidification process generates non-equilibrium microstructures and significant amounts of internal residual stresses. This paper investigates the laser cladding of 420 martensitic stainless steel of two single beads produced by different process parameters (e.g., laser power, laser speed, and powder feed rate). Metallographic sample preparation from the cross section revealed three distinct zones: the bead zone, the dilution zone, and the heat-affected zone (HAZ). The tensile residual stresses were in the range of 310-486 MPa on the surface and the upper part of the bead zone. The compressive stresses were in the range of 420-1000 MPa for the rest of the bead zone and the dilution zone. The HAZ also showed tensile residual stresses in the range of 140-320 MPa for both samples. The post-cladding heat treatment performed at 565 °C for an hour had significantly reduced the tensile stresses at the surface and in the subsurface and homogenized the compressive stress throughout the bead and dilution zones. The microstructures, residual stresses, and microhardness profiles were correlated for better understanding of the laser-cladding process.

Weldability aspects of a newly developed duplex stainless steel LDX 2101

Energy Technology Data Exchange (ETDEWEB)

Westin, E.M. [Avesta Research Centre, Avesta (Sweden). Outokumpu Stainless; Brolund, B. [SSAB Tunnplat, Borlaenge (Sweden); Hertzman, S. [Outokumpu Stainless Research Foundation, Stockholm (Sweden)

2008-06-15

Duplex grades have, due to balanced chemical compositions of both filler and base metals, a weldability that allows for successful welding using a majority of the technically relevant techniques of today. In order to fulfil the performance requirements several aspects must be considered. In the heat affected zone (HAZ) the austenite reformation must be reasonably high and in the weld metal the microstructure must be stable so that e.g. high productivity welding and multi-pass welding are possible, without precipitation of detrimental phases in previous passes. This paper addresses the effect of alloying elements and thermal cycles on phase balance in the high temperature HAZ (HTHAZ) of the newly developed lean duplex grade LDX 2101 (EN 1.4162, UNS S32101). Bead-on-plate welds and simulated weld structures have been produced and investigated using metallography, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The results are analysed using the thermodynamic database Thermo-Calc and a model for phase transformation based on a paraequilibrium assumption for ferrite-austenite transformation. In the temperature region outside the paraequilibrium domain, growth controlled by diffusion of substitutional elements was considered. The analysis follows a model by Cahn regarding grain boundary nucleated growth and the Hillert-Engberg model on kinetics of spherical and planar growth. (orig.)

Evaluation of Trace Elements and Their Relationship with Growth and Development of Young Children.

Science.gov (United States)

Cao, Jia; Gao, Zhenyan; Yan, Jin; Li, Minming; Su, Jia; Xu, Jian; Yan, Chong-Huai

2016-06-01

This study was conducted to assess the levels of trace elements and their relationship with growth and development of children in Shanghai, China, to offer scientific evidence for supplementing trace elements in children. A stratified, clustered, random sampling method was used in the study. Blood samples were taken from 2141 Shanghai children from 0 to 6.0 years old, and the concentrations of zinc (Zn), calcium (Ca), iron (Fe), copper (Cu), and magnesium (Mg) were measured using inductively coupled plasma mass spectrometry (ICP-MS). Nutritional status was determined and Z-scores of anthropometric parameters, such as height for age (HFA), weight for age (WFA), and body mass index (BMI) were calculated, indicated by HAZ, WAZ, and BMIZ, respectively. The overall median blood levels of Zn, Ca, Fe, Cu, and Mg were 8.83, 79.02, 9.49, 1.04, and 15.45 mg/L, respectively. Fe, Cu, and Mg increased with age and Zn, Fe, and Cu differed by sex. HAZ and WAZ were positively correlated with Zn (r (2) = 0.072 and 0.053, respectively; P children's growth and development. Dietary supplementation and screening of nutritional states are potential solutions to improve children's growth and development.

Process-Structure-Property Relationships for 316L Stainless Steel Fabricated by Additive Manufacturing and Its Implication for Component Engineering

Science.gov (United States)

Yang, Nancy; Yee, J.; Zheng, B.; Gaiser, K.; Reynolds, T.; Clemon, L.; Lu, W. Y.; Schoenung, J. M.; Lavernia, E. J.

2017-04-01

We investigate the process-structure-property relationships for 316L stainless steel prototyping utilizing 3-D laser engineered net shaping (LENS), a commercial direct energy deposition additive manufacturing process. The study concluded that the resultant physical metallurgy of 3-D LENS 316L prototypes is dictated by the interactive metallurgical reactions, during instantaneous powder feeding/melting, molten metal flow and liquid metal solidification. The study also showed 3-D LENS manufacturing is capable of building high strength and ductile 316L prototypes due to its fine cellular spacing from fast solidification cooling, and the well-fused epitaxial interfaces at metal flow trails and interpass boundaries. However, without further LENS process control and optimization, the deposits are vulnerable to localized hardness variation attributed to heterogeneous microstructure, i.e., the interpass heat-affected zone (HAZ) from repetitive thermal heating during successive layer depositions. Most significantly, the current deposits exhibit anisotropic tensile behavior, i.e., lower strain and/or premature interpass delamination parallel to build direction (axial). This anisotropic behavior is attributed to the presence of interpass HAZ, which coexists with flying feedstock inclusions and porosity from incomplete molten metal fusion. The current observations and findings contribute to the scientific basis for future process control and optimization necessary for material property control and defect mitigation.

Parametric studies of cutting zircaloy-2 sheets with a laser beam

International Nuclear Information System (INIS)

Ghosh, S.; Badgujar, B.P.; Goswami, G.L.

1996-01-01

The highly reactive and pyrophoric nature of zirconium alloys limits the use of conventional thermal sources (e.g., plasma arc cutting, oxygen flame cutting, etc.) for the cutting and drilling of these alloys. In this context, a highly coherent laser beam provides a good alternative for the cutting and drilling. In the present paper, laser beam cutting of zircaloy-2 sheets of 1.1 mm and 0.74 mm thickness is performed using a 300 W average power pulsed Nd:YAG laser. Pulse energy, pulse repetition rate, nozzle gap, gas pressure and cutting speed were varied to give different laser cutting conditions. Metallographic study of the cut surfaces showed the presence of transformed beta phase in the heat affected zone (HAZ) near the cut surface. The microhardness value across the cut surface was also measured. It showed a gradual increase in microhardness from the base metal (160 VHN) towards the HAZ having a maximum value of 365 VHN. The results of parametric studies of the cutting indicated that, with proper selection of process parameters, very narrow cuts can be easily made in zircaloy-2 using a pulsed Nd:YAG laser with a saving in material and at a much faster rate than alternative processes such as plasma arc cutting and oxygen flame cutting

Assessment of the integrity of ferritic-austenitic dissimilar weld joints of different grades of Cr-Mo ferritic steels

Energy Technology Data Exchange (ETDEWEB)

Laha, K.; Chandravathi, K.S.; Parameswaran, P.; Goyal, Sunil; Mathew, M.D. [Indira Gandhi Centre for Atomic Research, Kalpakkam (India). Metallurgy and Materials Group

2010-07-01

Integrity of the 2.25 Cr-1Mo / Alloy 800, 9Cr-1Mo / Alloy 800 and 9Cr-1Mo-VNb / Alloy 800 ferritic-austenitic dissimilar joints, fusion welded employing Inconel 182 electrode, has been assessed under creep conditions at 823 K. The dissimilar weld joints displayed lower creep rupture strength than their respective ferritic steel base metals. The strength reduction was more for 2.25Cr-1Mo steel joint and least for 9Cr-1Mo steel joint. The failure location in the joints was found to shift from the ferritic steel base metal to the intercritical region of heat-affected zone (HAZ) in ferritic steel (type IV cracking) with decrease in stress. At still lower stresses the failure occurred at the ferritic / austenitic weld interface. Localized creep deformation and cavitation in the soft intercritical HAZ induced type IV failure whereas creep cavitation at the weld interface particles induced ferritic / austenitic interface cracking due to high creep strength mismatch across it. Micromechanisms of type IV failure and interface cracking in the ferritic / austenitic joints and different susceptibility to failure for different grades of ferritic steels are discussed based on microstructural investigation, mechanical testing and finite element analysis. (Note from indexer: paper contains many typographical errors.)

Freqüência à creche e outros condicionantes do estado nutricional infantil Attendance at day-care centers and other conditioning factors in child nutritional status

Directory of Open Access Journals (Sweden)

Marina Vieira da Silva

1998-06-01

Full Text Available O estudo descreve o estado nutricional de 2 096 pré-escolares atendidos nos 27 Centros Educacionais e Creches do município de Piracicaba, estado de São Paulo. Observa-se que 5,1% das crianças apresentam déficit de altura/idade (escore ZAI The study describes the nutritional status of 2 096 preschool children attending 27 Educational Centers and Day-Care Centers in Piracicaba, state of São Paulo. Five point one percent of the children are observed to present a height/age deficit (score HAZ<-2.0 and a proportion of 1.2 with weight/height deficit (score WHZ<-2.0. The results reveal that per capita income, mother schooling, type of sewage, type of housing and attendance time at are the variables that cause impact on the HAZ score of the children.The positive association detected between attendance time at and -Z score of height for age stresses the importance of these investments as means to protect children, mainly against chronic malnutrition, as basic care with health, feeding and hygiene is associated with education. The day-care center also provides the participation of mothers in the work market, which is very important in poor families in order to increase family income.

Medical Surveillance Monthly Report (MSMR). Volume 23, Number 6, June 2016

Science.gov (United States)

2016-06-01

controls , ice and snow fall haz- ards should be emphasized in all locations. Stationary vehicles (suggested ICD-10: V87.8XXA). A lack of familiarity or...consider engineering controls or procedures associated with vehicle struc- ture, night vision, load carriage, fatigue, and/or individuals’ balance ...matrix. Inj Prev. 2002; 8(2):91–96. 15. Department of Health and Human Services, Centers for Disease Control and Prevention. Slip, Trip, and Fall

Mathematics Teachers’ Opinions on Worksheets Prepared with GeoGebra [Matematik Öğretmenlerinin GeoGebra ile Hazırlanan Çalışma Yaprakları Üzerine Görüşleri

Directory of Open Access Journals (Sweden)

Semirhan Gökçe

2016-04-01

ve öğretim sürecine katma noktasında eksiklerinin olduğu, kendilerini yeterli görmedikleri anlaşılmaktadır. Buradan hareketle bu çalışmada GeoGebra kullanılarak öğretmenlerin öğretim sürecinde ve öncesinde uzman yardımı almaksızın doğrudan uygulayabilecekleri çalışma yapraklarının geliştirilmesi ve hazırlanan çalışma yapraklarının uygulanabilirliği ve etkililiği üzerine görüşlerinin incelenmesi amaçlanmıştır. Özel durum çalışması yönteminin kullanıldığı araştırmanın katılımcılarını bir Anadolu lisesinde görev yapan beş matematik öğretmeni oluşturmaktadır. Verilerin toplanmasında yarı-yapılandırılmış mülakatlar kullanılmıştır. Bulgular çalışma yapraklarının matematik öğretimine etkileri, öğretim sürecinde kullanımının öğrenciler üzerindeki etkileri, uygulanması için gerekli eğitim altyapısı ve öğretim sürecinde uygulanabilirliği kapsamında ele alınmıştır. Kullanılan çalışma yapraklarının öğrenci merkezli olmasının, bilgisayar destekli eğitime yönelik bir yazılımı öğreten yapıda olmasının, özellikle de uzman yardımı almaksızın temel bilgisayar bilgisiyle uygulanabilmesinin bilgisayarı öğretim ortamlarında etkin biçimde kullanmak isteyen öğretmenlere katkı sağlayacağı düşünülmektedir.

Effect of weld heat input on toughness and structure of HAZ of a new ...

Indian Academy of Sciences (India)

Unknown

Key Laboratory of Liquid Structure and Heredity of Materials, Ministry of Education, School of Materials Science .... should be controlled (t8/5 = 10 ~ 20 s) to improve tough- ness in the .... nology, Harbin Institute of Technology, People's Repub-.

Süt Tozundan Yararlanılarak Hazırlanan İçme Sütleri

Directory of Open Access Journals (Sweden)

İlbilge Saldamlı

2015-02-01

Full Text Available Bilindiği gibi süt memeli hayvanların doğumdan sonra meme bezlerinden salgılanan kendisine özgü tad, koku ve kıvamda beyazımsı bir sıvıdır. Doğanın yeni doğan yavruya verdiği bu sıvı, o canlının yaşamasında ve yaşamını sürdürmesinde ilk tüketim maddesi olup beslenme süreci içinde vazgeçilmeyen bir gıdadır. Bileşiminde organizmanın bütün isteklerini karşılayabilecek besin elementleri tam ve yeter oranda bulunmaktadır. Bu nedenle süt günümüzde beslenmede ki yerini haklı olarak muhafaza etmektedir.

Microhardness Testing of Aluminum Alloy Welds

Science.gov (United States)

Bohanon, Catherine

2009-01-01

A weld is made when two pieces of metal are united or fused together using heat or pressure, and sometimes both. There are several different types of welds, each having their own unique properties and microstructure. Strength is a property normally used in deciding which kind of weld is suitable for a certain metal or joint. Depending on the weld process used and the heat required for that process, the weld and the heat-affected zone undergo microstructural changes resulting in stronger or weaker areas. The heat-affected zone (HAZ) is the region that has experienced enough heat to cause solid-state microstructural changes, but not enough to melt the material. This area is located between the parent material and the weld, with the grain structure growing as it progresses respectively. The optimal weld would have a short HAZ and a small fluctuation in strength from parent metal to weld. To determine the strength of the weld and decide whether it is suitable for the specific joint certain properties are looked at, among these are ultimate tensile strength, 0.2% offset yield strength and hardness. Ultimate tensile strength gives the maximum load the metal can stand while the offset yield strength gives the amount of stress the metal can take before it is 0.2% longer than it was originally. Both of these are good tests, but they both require breaking or deforming the sample in some way. Hardness testing, however, provides an objective evaluation of weld strengths, and also the difference or variation in strength across the weld and HAZ which is difficult to do with tensile testing. Hardness is the resistance to permanent or plastic deformation and can be taken at any desired point on the specimen. With hardness testing, it is possible to test from parent metal to weld and see the difference in strength as you progress from parent material to weld. Hardness around grain boundaries and flaws in the material will show how these affect the strength of the metal while still

Resiliencia, tamaño de grano y microestructura generada en la ZAC de los aceros HSLA 450 EMZ soldados bajo un proceso SMAW

Directory of Open Access Journals (Sweden)

González, R.

2001-12-01

Full Text Available In this paper several features of the HAZ between the weld metal and the parent metal, after the heat cycle produced by a SMAW process in 450 N/mm² HSLA steels are analysed, taking into consideration the temperatures reached in the HAZ as from Rosenthal's equation. The aspects under examination are: grain morphology by means of micrographs obtained with the Scannig Electron Microscopy to check the bands that control the grain size due to the microalloyings of the designed steel, taking into account the temperatures reached and the cooling rate in each of the HAZ regions; fracture toughness, checked by means of CTOD testing; hardness grain size determined by the Ashby and Esterling procedure^[1] and based on the values obtained with the Heyn method^[2] , ratio between stable growth and heat input; CTOD values which are found to be satisfactory under the welding conditions with a heat input of 1.6 Kj/mm.

Tras el ciclo térmico producido por un proceso de soldadura manual con electrodo revestido (SMAW, en los aceros HSLA de 450 N/ mm² y, considerando las temperaturas alcanzadas en la ZAC según la ecuación de Rosenthal, se analizan los siguientes aspectos en esta zona (ZAC, entre el metal de soldadura y el metal base: la morfología del grano mediante micrografías obtenidas en el microscopio electrónico de barrido, comprobando las barreras que pinzan el grano debido a los microaleantes de este acero de diseño, teniendo en cuenta las temperaturas alcanzadas y la velocidad de enfriamiento en cada una de las regiones de la ZAC; la tenacidad a la fractura mediante los ensayos de CTOD; la dureza; el tamaño de grano, mediante el procedimiento de Ashby y Esterling^[1] y basado en los valores obtenidos por el método de Heyn^[2]; la proporcionalidad entre el crecimiento estable y la energía calorífica aportada; los valores de CTOD, satisfactorios en las condiciones de soldeo con

Cyclic deformation of dissimilar welded joints between Ti–6Al–4V and Ti17 alloys: Effect of strain ratio

Energy Technology Data Exchange (ETDEWEB)

Wang, S.Q. [State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, 127 Youyi Road, Xi' an 710072 (China); Department of Mechanical and Industrial Engineering, Ryerson University, 350 Victoria Street, Toronto, Ontario M5B 2K3 (Canada); Liu, J.H., E-mail: jinhliu@nwpu.edu.cn [State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, 127 Youyi Road, Xi' an 710072 (China); Lu, Z.X. [Department of Materials Science and Engineering, Xi' an University of Technology, 5 Jinhuanan Road, Xi' an 710048 (China); Chen, D.L., E-mail: dchen@ryerson.ca [Department of Mechanical and Industrial Engineering, Ryerson University, 350 Victoria Street, Toronto, Ontario M5B 2K3 (Canada)

2014-03-01

Cyclic deformation characteristics of electron beam welded (EBWed) joints between Ti–6Al–4V and Ti17 (Ti–5Al–4Mo–4Cr–2Sn–2Zr) titanium alloys were evaluated via strain-controlled low-cycle fatigue tests at varying strain ratios at a constant strain amplitude. The welding led to a significant microstructural change across the dissimilar joint, with hexagonal close-packed (HCP) martensite α' and orthorhombic martensite α″ in the fusion zone (FZ), α' in the heat-affected zone (HAZ) of Ti–6Al–4V side, and coarse β in the HAZ of Ti17 side. A distinctive asymmetrical hardness profile across the joint was observed with the highest hardness in the FZ and a lower hardness in the HAZ of Ti17 side than in the Ti17 base metal (BM), indicating the presence of soft zone. The strength and ductility of the dissimilar joint lay in-between those of two base metals (BMs). Unlike wrought magnesium alloys, the Ti–6Al–4V BM, Ti17 BM, and joint basically exhibited symmetrical hysteresis loops in tension and compression in the fully reversed strain-controlled tests at a strain ratio of R{sub ε}=−1. At a strain ratio of R{sub ε}=0 and 0.5, a large amount of plastic deformation occurred in the ascending phase of the first cycle of hysteresis loops of Ti–6Al–4V BM, Ti17 BM, and joint due to the high positive mean strain values. Fatigue life of the joint was observed to be the longest at R{sub ε}=−1, and it decreased as the strain ratio deviated from R{sub ε}=−1. A certain degree of mean stress relaxation was observed in the non-fully reversed strain controlled tests (i.e., R{sub ε}≠−1). Fatigue failure of the dissimilar joints occurred in the Ti–6Al–4V BM, with crack initiation from the specimen surface or near-surface defect and crack propagation characterized by fatigue striations.

Experimental and numerical investigation on under-water friction stir welding of armour grade AA2519-T87 aluminium alloy

OpenAIRE

Sree Sabari, S.; Malarvizhi, S.; Balasubramanian, V.; Madusudhan Reddy, G.

2016-01-01

Friction stir welding (FSW) is a promising welding process that can join age hardenable aluminium alloys with high joint efficiency. However, the thermal cycles experienced by the material to be joined during FSW resulted in the deterioration of mechanical properties due to the coarsening and dissolution of strengthening precipitates in the thermo-mechanical affected zone (TMAZ) and heat affected zone (HAZ). Under water friction stir welding (UWFSW) is a variant of FSW process which can maint...

Gas Metal Arc Welding Process Modeling and Prediction of Weld Microstructure in MIL A46100 Armor-Grade Martensitic Steel

Science.gov (United States)

2013-06-01

earlier in Fig. 4(a) to construct the corresponding CCT diagram , Fig. 5. The diagram displayed in Fig. 5 is obtained under particular continuous-cooling...TTT and CCT diagrams are necessary, but not sufficient, input for a phase volume-fraction determination procedure. That is, in addition to knowing the...fraction of bainite to the instantaneous temperature for the MIL A46100 HAZ section which was described using TTT and CCT diagrams displayed in Fig. 4(a

Isostatic lines’ study to optimize steel space grid envelope structures for tall buildings according to their solicitations

OpenAIRE

Señís López, Roger

2013-01-01

Based on the first study completed with wind tunnel tests, the aim of this paper is to define a second methodology for the optimization of steel space grid envelope structures for tall buildings according to their isostatic lines according to their solicitations. It is by means of the comparison NatHaz online database and numerical simulation research of wind flow repercussion in buildings, through Computational Fluid Dynamics (CDF), that we can understand and analyse the grid ...

Evaluation of Fire Hazard and Safety Management of Heritage Buildings in Georgetown, Penang

OpenAIRE

Othuman Mydin M.A.; Sani N. Md; Abas N.F.; Khaw Y.Y.

2014-01-01

Fire is a subject that is always neglected and ignored as far as heritage buildings are concerned. Unlike newly-built buildings, which are required under UBBL to undergo certain fire protection system tests, people are less likely to carry out such tests and detailed assessments for heritage buildings. Thus, this research is significant as it is aimed at accomplishing several objectives including studying the current fire emergency plan, besides identifying and assessing the possible fire haz...

AMİNOPROPİL SİLİKAJEL İMMOBİLİZE KALİKS[4]AREN POLİMERİ (K[4]APS KULLANILARAK p-NİTROFENOLÜN SULU ÇÖZELTİLERDEN GİDERİMİ

Directory of Open Access Journals (Sweden)

Vahti Aladağlı

2015-11-01

Full Text Available Bu çalışma yeni polimerik kaliksaren türevinin hazırlanması ve p-nitrofenolün (PNF adsorpsiyonunda sorbent malzemesi olarak uygulanmasını içermektedir. Kaliksaren türevleri 1-5'in hazırlanmasından sonra, 5 no'lu moleküle aminopropil silika jel destek maddesi tutturularak polimerik kaliksaren 6 türevi elde edildi. Bütün bileşikler, FTIR, 1H NMR, elemental analizi, TGA ve SEM gibi metotlar kullanılarak karakterize edildi. Aminopropil silika jel immobilize kaliks[4]aren (K[4]APS 6, PNF adsorpsiyonu çalışmalarında sorbent olarak kullanılmış ve pH, etkileşim süresi, konsantrasyon, proses sıcaklığı ve sorbent dozajı gibi parametreler çalışıldı. Sonuçlara göre, 6 no'lu molekülün PNF adsorpsiyonu için optimum koşullar pH 6, etkileşim süresi 1 saat, PNF konsantrasyonu 5.0x10-5 M, sorbent dozajı 0.025g ve proses sıcaklığı 25oC olarak bulundu. PNF adsorpsiyon mekanizması, Langmuir ve Freundlich izotermleri ile değerlendirildi

PR-EDB: Power Reactor Embrittlement Data Base, Version 2. Revision 2, Program description

Energy Technology Data Exchange (ETDEWEB)

Stallmann, F.W.; Wang, J.A.; Kam, F.B.K.; Taylor, B.J. [Oak Ridge National Lab., TN (United States)

1994-01-01

Investigations of regulatory issues such as vessel integrity over plant life, vessel failure, and sufficiency of current codes Standard Review Plans (SRP`s) and Guides for license renewal can be greatly expedited by the use of a well-designed computerized data base. Also, such a data base is essential for the validation of embrittlement prediction models by researchers. The Power Reactor Embrittlement Data Base (PR-EDB) is such a comprehensive collection of data for US commercial nuclear reactors. The current version of the PR-EDB contains the Charpy test data that were irradiated in 252 capsules of 96 reactors and consists of 207 data points for heat-affected-zone (HAZ) materials (98 different HAZ), 227 data points for weld materials (105 different welds), 524 data points for base materials (136 different base materials), including 297 plate data points (85 different plates), 119 forging data points (31) different forging), and 108 correlation monitor materials data points (3 different plates). The data files are given in dBASE format and can be accessed with any computer using the DOS operating system. ``User-friendly`` utility programs are used to retrieve and select specific data, manipulate data, display data to the screen or printer, and to fit and plot Charpy impact data. The results of several studies investigated are presented in Appendix D.

Corrosion fatigue crack growth behaviour of low-alloy RPV steels at different temperatures and loading frequencies under BWR/NWC environment

International Nuclear Information System (INIS)

Ritter, S.; Seifert, H.P.

2004-01-01

The strain-induced corrosion cracking or low-frequency corrosion fatigue (LFCF) crack growth behaviour of different reactor pressure vessel (RPV) steels and of a RPV weld filler/weld heat-affected zone (HAZ) material were characterized under simulated transient boiling water reactor/normal water chemistry conditions by cyclic fatigue tests with pre-cracked fracture mechanics specimens. The experiments were performed in oxygenated high-temperature water at temperatures of either 288, 250, 200, or 150 deg. C. Modern high-temperature water loops, on-line crack growth monitoring (DCPD) and fractographic analysis by SEM were used to quantify the cracking response. Under low-flow and highly oxidising conditions (ECP > 0 mV SHE , O 2 = 0.4 ppm) the cycle-based LFCF crack growth rates (CGR) Δa/ΔN increased with decreasing loading frequency and increasing temperature with a maximum/plateau at/above 250 deg. C. Sustained environmentally-assisted crack growth could be maintained down to low frequencies of 10 -5 Hz. The LFCF CGR of low- and high-sulphur steels and of the weld filler/HAZ material were comparable over a wide range of loading conditions and conservatively covered by the 'high-sulphur line' of the General Electric-model. The 'ASME XI wet fatigue CGR curves' could be significantly exceeded in all materials by cyclic fatigue loading at low frequencies ( -2 Hz) at high and low load ratios R. (authors)

Association of whole blood n-6 fatty acids with stunting in 2-to-6-year-old Northern Ghanaian children: A cross-sectional study.

Directory of Open Access Journals (Sweden)

Mary Adjepong

Full Text Available In Northern Ghana, 33% of children are stunted due to economic disparities. Dietary fatty acids (FA are critical for growth, but whether blood FA levels are adequate in Ghanaian children is unknown. The objective of this study was to determine the association between whole blood FAs and growth parameters in Northern Ghanaian children 2-6 years of age. A drop of blood was collected on an antioxidant treated card and analyzed for FA composition. Weight and height were measured and z-scores were calculated. Relationships between FAs and growth parameters were analyzed by Spearman correlations, linear regressions, and factor analysis. Of the 307 children who participated, 29.7% were stunted and 8% were essential FA deficient (triene/tetraene ratio>0.02. Essential FA did not differ between stunted and non-stunted children and was not associated with height-for-age z-score (HAZ or weight-for-age z-score (WAZ. In hemoglobin adjusted regression models, both HAZ and WAZ were positively associated with arachidonic acid (p≤0.01, dihomo-gamma-linolenic acid (DGLA, p≤0.05, docosatetraenoic acid (p≤0.01 and the ratio of DGLA/linoleic acid (p≤0.01. These data add to the growing body of evidence indicating n-6 FAs are critical in childhood linear growth. Our findings provide new insights into the health status of an understudied Northern Ghanaian population.

Effect of Al content on critical CTOD properties in heat affected zone of C-Mn microalloyed steel. Teitanso teigokin koyosetsu netsu eikyobu no genkai CTOD tokusei ni oyobosu Al ganyuryo no eikyo

Energy Technology Data Exchange (ETDEWEB)

Fukada, Y.; Komizo, Y. (Sumitomo Metal Industries Ltd., Osaka (Japan))

1992-08-05

Two types of molten alloys specimen with a base of 0.10%C-0.20%Si-1.40%Mn-0.01%Ti system and varied Al content, were studied. The critical crack tip opening displacement(CTOD) properties in heat effected zone(HAZ) of extreme low Al content steel was stable at. extremely low temperature and there was no formation of M-A. Fine ferrite has a texture of [alpha] main body and it has been thought that the the change in the CTOD properties with the variation in Al content has been due to the difference in the texture. In case of Al content steel plate, the interfacial energy has been decreased due to excessive carbon concentration at [gamma] /[alpha] interface, M-A formation has been easier by the suppression of [alpha] transformation. In case of extremely low Al content steel plate, [alpha] transformation has been promoted and cementite deposition has been estimated from a small amount. of left [gamma] of extremely high carbon concentration. As for SH-CCT diagram of extremely low Al content steel plate, compare to Al content steel plate, [alpha] noze has shifted toward shorter time and formation of [alpha] has been easier within the normal welding cooling rate, and microstructures of [alpha] texture have formed in HAZ. 21 refs., 12 figs., 1 tab.

Underclad cracks growth under fatigue loading in stainless steel cladding

International Nuclear Information System (INIS)

Bernard, J.L.; Bodson, F.; Doule, A.; Slama, G.; Bramat, M.; Doucet, J.P.; Maltrud, F.

1981-01-01

Hydrogen induced cracks have been found in HAZ of PWR vessel nozzles under stainless steel cladding. Fatigue tests were performed to collect a large amount of data on the possible propagation of this type of flaws. Tests were conducted in two steps. The aim of the first step was to set up the experimental equipment and to device an adequate method for following cracks during fatigue loading. Clad plates with electroerosion machined slots were used for this purpose. The second step was then undertaken with material taken out of an actual nozzle containing hydrogen induced cracks in the HAZ under stainless steel cladding or flaws simulated by electroerosion machined slots. The test loadings were comparable to in service loadings of the nozzles. Special attention was taken to get representative R ratios. Again for the sake of representativity, the tests were performed at 300 0 C (In service temperature) and the hydrotest was simulated. The main results are: It was possible to follow the whole failure process by combining non-destructive examinations during fatigue testing and fractographic observations of broken specimens. Different striation patterns, before and after air has penetrated the actual embedded cracks were observed. Numerical simulation of fatigue crack growth of actual or simulated defects were consistent with experimental data, provided mainly that defect shape, effect of R ratio and of environment were taken into account. (orig.)

Microstructure characteristics and temperature-dependent high cycle fatigue behavior of advanced 9% Cr/CrMoV dissimilarly welded joint

International Nuclear Information System (INIS)

Wu, Qingjun; Lu, Fenggui; Cui, Haichao; Ding, Yuming; Liu, Xia; Gao, Yulai

2014-01-01

Advanced 9% Cr and CrMoV steels chosen as candidate materials are first welded by narrow-gap submerged arc welding (NG-SAW) to fabricate the heavy section rotor. The present work focuses on studying the high-cycle fatigue (HCF) behavior of advanced 9% Cr/CrMoV dissimilarly welded joint at different temperatures. Conditional fatigue strength of this dissimilarly welded joint was obtained by HCF tests at room temperature (RT), 400 °C and 470 °C. It was observed that the failure occurred at the side of CrMoV base metal (BM), weld metal (WM) and heat affected zone (HAZ) of CrMoV side over 5×10 7 cycles for the specimens tested at RT, 400 °C and 470 °C. The detailed microstructures of BMs, WMs and HAZs as well as fracture appearance were observed by optical microscopy (OM) and scanning electron microscopy (SEM). Precipitation and aggregation of carbides along the grain boundaries were clearly detected with the increase of temperature, which brought a negative effect on the fatigue properties. It is interesting to note that the inclusion size leading to crack initiation became smaller for the HCF test at higher temperature. Therefore, reduction in the inclusion size in a welded joint helps to improve the HCF performance at high temperature

Effect of Welding Processes on the Microstructure, Mechanical Properties and Residual Stresses of Plain 9Cr-1Mo Steel Weld Joints

Science.gov (United States)

Nagaraju, S.; Vasantharaja, P.; Brahadees, G.; Vasudevan, M.; Mahadevan, S.

2017-12-01

9Cr-1Mo steel designated as P9 is widely used in the construction of power plants and high-temperature applications. It is chosen for fabricating hexcan fuel subassembly wrapper components of fast breeder reactors. Arc welding processes are generally used for fabricating 9Cr-1Mo steel weld joints. A-TIG welding process is increasingly being adopted by the industries. In the present study, shielded metal arc (SMA), tungsten inert gas (TIG) and A-TIG welding processes are used for fabricating the 9Cr-1Mo steel weld joints of 10 mm thickness. Effect of the above welding processes on the microstructure evolution, mechanical properties and residual stresses of the weld joints has been studied in detail. All the three weld joints exhibited comparable strength and ductility values. 9Cr-1Mo steel weld joint fabricated by SMAW process exhibited lower impact toughness values caused by coarser grain size and inclusions. 9Cr-1Mo steel weld joint fabricated by TIG welding exhibited higher toughness due to finer grain size, while the weld joint fabricated by A-TIG welding process exhibited adequate toughness values. SMA steel weld joint exhibited compressive residual stresses in the weld metal and HAZ, while TIG and A-TIG weld joint exhibited tensile residual stresses in the weld metal and HAZ.

Evaluation of Electron Beam Welding Performance of AA6061-T6 Plate-type Fuel Assembly

International Nuclear Information System (INIS)

Kim, Soo-Sung; Seo, Kyoung-Seok; Lee, Don-Bae; Park, Jong-Man; Lee, Yoon-Sang; Lee, Chong-Tak

2014-01-01

As one of the most commonly used heat-treatable aluminum alloys, AA6061-T6 aluminum alloy is available in a wide range of structural materials. Typically, it is used in structural members, auto-body sheet and many other applications. Generally, this alloy is easily welded by conventional GTAW (Gas Tungsten Arc Welding), LBW (Laser Beam Welding) and EBW(Electron Beam Welding). However, certain characteristics, such as solidification cracking, porosity, HAZ (Heat-affected Zone) degradation must be considered during welding. Because of high energy density and low heat input, especially LBW and EBW processes possess the advantage of minimizing the fusing zone and HAZ and producing deeper penetration than arc welding processes. In present study, to apply for the plate-type nuclear fuel fabrication and assembly, a fundamental electron beam welding experiment using AA6061-T6 aluminum alloy specimens was conducted. Furthermore, to establish the suitable welding process, and satisfy the requirements of the weld quality, EBW apparatus using an electron welding gun and vacuum chamber was developed, and preliminary investigations for optimizing the welding parameters of the specimens using AA6061-T6 aluminum plates were also performed. The EB weld quality of AA6061-T6 aluminum alloy for the plate-type fuel assembly has been also studied by the weld penetrations of side plate to end fitting and fixing bar and weld inspections using computed tomography

Construcción de un escáner tridimensional usando C++ y hardware libre

Directory of Open Access Journals (Sweden)

Cristian Enrique Gamboa

2017-01-01

Full Text Available En este trabajo, se desarrolló un sistema económico de escaneo tridimensional (3D que permite obtener información de la estructura física de un determinado objeto a partir de la cual, se genera un modelo digital. Este sistema opera proyectando un haz de luz láser en forma de línea sobre el objeto, mientras rota sobre su propio eje (eje z, el haz de luz crea un perfil del objeto, el cual es capturado mediante vídeo de alta definición (HD por una cámara. A través del procesamiento digital de las imágenes capturadas se obtienen los vértices del objeto y se construye el modelo tridimensional. Para llevar a cabo esta tarea, el escáner 3D está formado por un conjunto de elementos de hardware y software libre como lo son: la plataforma Arduino, que permite realizar el control del hardware de escaneo, y un software desarrollado en C++ que implementando las librerías OpenCv y OpenGl, permite la realización de las tareas de procesamiento y análisis de imágenes. Estos elementos hacen que este desarrollo, se  constituya como incursión económica en la tecnología de escaneo laser tridimensional.

Microstructure characteristics and temperature-dependent high cycle fatigue behavior of advanced 9% Cr/CrMoV dissimilarly welded joint

Energy Technology Data Exchange (ETDEWEB)

Wu, Qingjun [Shanghai Key Laboratory of Materials Laser Processing and Modification, Shanghai Jiao Tong University, Shanghai 200240 (China); Lu, Fenggui, E-mail: Lfg119@sjtu.edu.cn [Shanghai Key Laboratory of Materials Laser Processing and Modification, Shanghai Jiao Tong University, Shanghai 200240 (China); Shanghai Key Laboratory of Modern Metallurgy and Materials Processing, Shanghai University, Shanghai 200072 (China); Cui, Haichao [Shanghai Key Laboratory of Materials Laser Processing and Modification, Shanghai Jiao Tong University, Shanghai 200240 (China); Ding, Yuming; Liu, Xia [Shanghai Turbine Plant of Shanghai Electric Power Generation Equipment Co. Ltd., Shanghai 200240 (China); Gao, Yulai, E-mail: ylgao@shu.edu.cn [Shanghai Key Laboratory of Modern Metallurgy and Materials Processing, Shanghai University, Shanghai 200072 (China)

2014-10-06

Advanced 9% Cr and CrMoV steels chosen as candidate materials are first welded by narrow-gap submerged arc welding (NG-SAW) to fabricate the heavy section rotor. The present work focuses on studying the high-cycle fatigue (HCF) behavior of advanced 9% Cr/CrMoV dissimilarly welded joint at different temperatures. Conditional fatigue strength of this dissimilarly welded joint was obtained by HCF tests at room temperature (RT), 400 °C and 470 °C. It was observed that the failure occurred at the side of CrMoV base metal (BM), weld metal (WM) and heat affected zone (HAZ) of CrMoV side over 5×10{sup 7} cycles for the specimens tested at RT, 400 °C and 470 °C. The detailed microstructures of BMs, WMs and HAZs as well as fracture appearance were observed by optical microscopy (OM) and scanning electron microscopy (SEM). Precipitation and aggregation of carbides along the grain boundaries were clearly detected with the increase of temperature, which brought a negative effect on the fatigue properties. It is interesting to note that the inclusion size leading to crack initiation became smaller for the HCF test at higher temperature. Therefore, reduction in the inclusion size in a welded joint helps to improve the HCF performance at high temperature.

Fractographic and microstructural aspects of fracture toughness testing in irradiated 304 stainless steel

International Nuclear Information System (INIS)

Cullen, W.H.; Hiser, A.L.; Hawthorne, J.R.; Abramczyk, G.A.; Caskey, G.R.

1987-01-01

Fracture toughness and Charpy impact test results on 304 stainless steel baseplate, weld and heat-affected zone (HAZ) tested at 25 0 C and 125 0 C are correlated with the microstructural and fractographic features observed in these materials. Specimens were collected from several sections of 12.7 mm (0.5 in.) wall thickness piping removed from a process system, and were characterized by different material chemistries and thermomechanical histories. As a result, mechanical properties vary over a considerable range from one pipe section to another. The presence of delta ferrite in some of the samples caused significant degradations in the toughness properties for certain crack orientations. Decreases in Charpy impact energies occur in the same material for different crack orientations. Materials irradiated showed 40% decreases in Charpy impact energy, but little change in fracture morphology. An increase in the test temperature resulted in an expected increase in Charpy energies for all materials. Fractographic features did not change appreciably with respect to the 100 0 C increase in test temperature. In unirradiated specimens, a test temperature increase caused lower J/sub Ic/ and J-R curve values with tearing modules values increased. The latter is due to the large decreases in tensile strength with increasing test temperature. The weld metals tend to have the highest tearing resistance, while the HAZ's tend to have the lowest. 30 figs., 3 tabs

MULTI-OBJECTIVE OPTIMISATION OF LASER CUTTING USING CUCKOO SEARCH ALGORITHM

Directory of Open Access Journals (Sweden)

M. MADIĆ

2015-03-01

Full Text Available Determining of optimal laser cutting conditions for improving cut quality characteristics is of great importance in process planning. This paper presents multi-objective optimisation of the CO2 laser cutting process considering three cut quality characteristics such as surface roughness, heat affected zone (HAZ and kerf width. It combines an experimental design by using Taguchi’s method, modelling the relationships between the laser cutting factors (laser power, cutting speed, assist gas pressure and focus position and cut quality characteristics by artificial neural networks (ANNs, formulation of the multiobjective optimisation problem using weighting sum method, and solving it by the novel meta-heuristic cuckoo search algorithm (CSA. The objective is to obtain optimal cutting conditions dependent on the importance order of the cut quality characteristics for each of four different case studies presented in this paper. The case studies considered in this study are: minimisation of cut quality characteristics with equal priority, minimisation of cut quality characteristics with priority given to surface roughness, minimisation of cut quality characteristics with priority given to HAZ, and minimisation of cut quality characteristics with priority given to kerf width. The results indicate that the applied CSA for solving the multi-objective optimisation problem is effective, and that the proposed approach can be used for selecting the optimal laser cutting factors for specific production requirements.

Long-term impact of the ketogenic diet on growth and resting energy expenditure in children with intractable epilepsy.

Science.gov (United States)

Groleau, Veronique; Schall, Joan I; Stallings, Virginia A; Bergqvist, Christina A

2014-09-01

The long-term effects of the ketogenic diet, a high fat diet for treating intractable epilepsy, on resting energy expenditure (REE) are unknown. The aim of this study was to evaluate the impact of 15 months of ketogenic diet treatment on growth and REE in children with intractable epilepsy. Growth, body composition, and REE were assessed at baseline, 3 months and 15 months in 24 children (14 males, 10 females; mean age 5 y 6 mo [SD 26 mo], range 7 mo-6 y 5 mo), 10 with cerebral palsy [CP]). Fifteen were identified as ketogenic diet responders at 3 months and continued on the ketogenic diet until 15 months. These were compared to 75 healthy children (43 males, 32 females; mean age 6 y 3 mo [SD 21 mo] age range 2-9 y). REE was expressed as percentage predicted, growth as height (HAz) and weight (WAz) z-scores, and body composition as fat and fat free mass (FFM). HAz declined -0.2 and -0.6 from baseline to 3 months and 15 months respectively (p = 0.001), while WAz was unchanged. In ketogenic diet responders, FFM, age and CP diagnosis predicted REE (overall R(2) = 0.76, pketogenic diet, linear growth status declined while weight status and REE were unchanged. REE remained reduced in children with CP. © 2014 Mac Keith Press.

Long-term impact of the ketogenic diet on growth and resting energy expenditure in children with intractable epilepsy

Science.gov (United States)

GROLEAU, VERONIQUE; SCHALL, JOAN I; STALLINGS, VIRGINIA A; BERGQVIST, CHRISTINA A

2014-01-01

AIM The long-term effects of the ketogenic diet, a high fat diet for treating intractable epilepsy, on resting energy expenditure (REE) are unknown. The aim of this study was to evaluate the impact of 15 months of ketogenic diet treatment on growth and REE in children with intractable epilepsy. METHOD Growth, body composition and REE were assessed at baseline, 3 and 15 months in 24 children (14 males, 10 females; mean age 5y 6mo (SD 26mo), range 7mo–6y 5mo), 10 with cerebral palsy [CP]). Fifteen were identified as ketogenic diet responders at 3 months and continued on the ketogenic diet until 15 months. These were compared to 75 healthy children (43 males, 32 females; mean age 6y 3mo [SD 21mo] age range 2–9y). REE was expressed as percentage predicted, growth as height (HAz) and weight (WAz) z-scores, and body composition as fat and fat free mass (FFM). RESULTS HAz declined −0.2 and −0.6 from baseline to 3 and 15 months, respectively (p=0.001), while WAz was unchanged. In ketogenic diet responders, FFM, age and CP diagnosis predicted REE (overall R2=0.76, pketogenic diet, linear growth status declined while weight status and REE were unchanged. REE remained reduced in children with CP. PMID:24749520

Increasing Weldability of Service-Aged Reformer Tubes by Partial Solution Annealing

Science.gov (United States)

Mostafaei, M.; Shamanian, M.; Purmohamad, H.; Amini, M.

2016-04-01

A dissimilar joint of 25Cr-35Ni/30Cr-48Ni (HP/HV) heat-resistant steels was evaluated. The investigations indicated that the as-cast HP alloy contained M7C3, M23C6, and NbC carbides and HV alloy with 5 wt.% tungsten, contained M23C6 and M6C carbides embedded in an austenitic matrix. After 8 years of ex-service aging at 1050 °C, the ductility of HP/HV reformer tubes was decreased dramatically, and thus, the repair welding of the aged HP/HV dissimilar joint was at a risk. In order to repair the aged reformer tubes and increase weldability properties, a new partial solution annealing treatment was designed. Mechanical testing results showed that partial solution annealing at 1200 °C for 6 h increased the elongation and toughness of the aged HP and HV alloys drastically. Also, a mechanism for constitutional liquation cracking in the heat-affected zones (HAZ) of the HP/HV dissimilar joint was proposed. In the HAZ of the aged HP/HV welded joint, the cracks around the locally melted carbides were initiated and propagated during carbides solidification at the cooling cycle of welding associated with the decrease in the ductility of the aged HP and HV alloys. In addition, Varestraint weldability test showed that the susceptibility to hot cracking was decreased with partial solution annealing.

Creep properties of welded joints in OFHC copper for nuclear waste containment

International Nuclear Information System (INIS)

Ivarsson, B.; Oesterberg, J.O.

1988-08-01

In Sweden it has been suggested that copper canisters are used for containment of spent nuclear fuel. These canisters will be subjected to temperatures up to 100 degrees C and external pressures up to 15 MPa. Since the material is pure (OFHC) copper, creep properties must be considered when the canisters are dimensioned. The canisters are sealed by electron beam welding which will affect the creep properties. Literature data for copper - especially welded joints - at the temperatures of interest is very scare. Therefore uniaxial creep tests of parent metal, weld metal, and simulated HAZ structures have been performed at 110 degrees C. These tests revealed considerable differences in creep deformation and rupture strength. The weld metal showed creep rates and rupture times ten times higher and ten times shorter, respectively, than those of the parent metal. The simulated HAZ was equally strongen than the parent metal. These differences were to some extent verified by results from creep tests of cross-welded specimens which, however, showed even shorter rupture times. Constitutive equations were derived from the uniaxial test results. To check the applicability of these equations to multiaxial conditions, a few internal pressure creep tests of butt-welded tubes were performed. Attemps were made to simulate their creep behaviour by constitutive equations were used. These calculations failed due to too great differences in creep deformation behaviour across the welded joint. (authors)

Relationship between Malnutrition and the Number of Permanent Teeth in Filipino 10- to 13-Year-Olds

Science.gov (United States)

Heinrich-Weltzien, Roswitha; Monse, Bella

2013-01-01

In the present study, we determined whether there is a delay in the eruption of permanent teeth (PT) among Filipino adolescents with stunting or thinness. Height, weight, and number of PT were recorded in 1554 Filipino 10- to 13-year-olds (711 boys; 843 girls). z-scores for height (HAZ) and body mass index (BMI) were calculated according to the WHO growth reference, and their correlations to the number of PT were assessed. 54.9% of the children have at least one form of malnutrition. Significantly, more boys (22.9%) than girls (16.5%) were thin, while no sex difference in stunting was noted (boys 48.5%; girls 44.0%). The number of PT was significantly correlated to HAZ and BMI-z-score. Stunted and thin students had significantly fewer PT than their nonaffected peers. These differences tended to be the result of delay in tooth eruption in thin and stunted adolescents. In 13-year-old girls, all PT were erupted regardless of their nutritional status indicating a catch-up. Thin and stunted boys had one tooth less than normal boys at this age. Impaired physical growth and dental development seem to have common risk factors. Therefore, regular monitoring of growth and dental development might be helpful for targeting support programmes in developing countries. PMID:24069590

Relationship between Malnutrition and the Number of Permanent Teeth in Filipino 10- to 13-Year-Olds

Directory of Open Access Journals (Sweden)

Roswitha Heinrich-Weltzien

2013-01-01

Full Text Available In the present study, we determined whether there is a delay in the eruption of permanent teeth (PT among Filipino adolescents with stunting or thinness. Height, weight, and number of PT were recorded in 1554 Filipino 10- to 13-year-olds (711 boys; 843 girls. z-scores for height (HAZ and body mass index (BMI were calculated according to the WHO growth reference, and their correlations to the number of PT were assessed. 54.9% of the children have at least one form of malnutrition. Significantly, more boys (22.9% than girls (16.5% were thin, while no sex difference in stunting was noted (boys 48.5%; girls 44.0%. The number of PT was significantly correlated to HAZ and BMI-z-score. Stunted and thin students had significantly fewer PT than their nonaffected peers. These differences tended to be the result of delay in tooth eruption in thin and stunted adolescents. In 13-year-old girls, all PT were erupted regardless of their nutritional status indicating a catch-up. Thin and stunted boys had one tooth less than normal boys at this age. Impaired physical growth and dental development seem to have common risk factors. Therefore, regular monitoring of growth and dental development might be helpful for targeting support programmes in developing countries.

Análisis de la metalurgia y mecánica de la fractura en la ZAC en un proceso por arco sumergido

Directory of Open Access Journals (Sweden)

González, R.

1999-06-01

Full Text Available High tensile, microalloyed steels, such as 450 EMZ design steels which are studied in this article, are used in offshore platforms and other structures subject to extreme working conditions, requiring high resilience and fracture toughness at low temperatures. These steels have been subject to a control in their welding parameters to obtain a low heat input which allows for the maintenance of correct toughness values in their heat affected zone (HAZ. The present article analyses the values of hardness, resilience and toughness, as well as the points of greatest brittleness of the HAZ (1.

Los aceros microaleados de alto límite elástico, grupo al que pertenecen los aceros de diseño 450 EMZ del presente trabajo, son aceros utilizados en plataformas offshore y estructuras sometidas a extremas condiciones de trabajo, a las que se les requiere alta resiliencia y tenacidad a la fractura a bajas temperaturas. Estos aceros son sometidos a un control en sus parámetros de soldadura a fin de recibir una baja energía calorífica, que permitan mantener unos valores de tenacidad adecuados en su zona afectada por el calor (ZAC. En este trabajo se pretenden analizar los valores obtenidos de dureza, resiliencia y tenacidad, así como los puntos de mayor fragilidad de la ZAC (1.

Malnutrition, Subsequent Risk of Mortality and Civil War in Burundi

OpenAIRE

Philip Verwimp

2011-01-01

The paper investigates the effect of child malnutrition on the risk of mortality in Burundi, a very poor country heavily affected by civil war. We use anthropometric data from a longitudinal survey (1998-2007). We find that undernourished children, as measured by the height-for-age z-scores (HAZ) in 1998 had a higher probability to die during subsequent years. In order to address the problem of omitted variables correlated with both nutritional status and the risk of mortality, we use the len...

Body composition at birth and height at 2 years: A prospective cohort study among children in Jimma, Ethiopia

OpenAIRE

Admassu, B.; Wells, J. C. K.; Girma, T.; Andersen, G. S.; Owino, V.; Belachew, T.; Michaelsen, K. F.; Abera, M.; Wibaek, R.; Friis, H.; Kaestel, P.

2017-01-01

BACKGROUND: Low birth weight is associated with childhood stunting, but equivalent associations for birth body composition (BC) remain unknown. The aim of this study was to assess associations between birth BC and height-for-age z-score (HAZ) at 2 years of age. / METHODS: In a prospective cohort study, fat mass (FM) and fat-free mass (FFM) were measured using air-displacement plethysmography within 48 h of birth. Linear regression models were applied to study the relationship between BC at bi...

Tropikal Metilsalisilat-Mentol Uygulamasının Rat Deri Flebi Yaşayabilirliği Üzerine Etkisi

OpenAIRE

Yenidünya, Mehmet Oğuz; Sevin, Kutlu; Ketene, Mehmet T.; Yormuk, Erdem

1993-01-01

Ratlarda hazırlanan random paternli pannikulus karnozusu içeren deri fleplerinde topikal uygulanan metilsalisilat-mentol'ün flep yaşayabilen alanı üzerindeki etkisi araştırıldı. Flep yaşayabilen alan ölçümleri milimetrik kağıt ile yapıldı. Sonuç olarak topikal metilsalisilat-mentol'ün random paternlirat deri fleplerinde yaşayabilen alanı artırdığı saptandı.

Hot wire TIG temper bead welding for nuclear repairs

International Nuclear Information System (INIS)

Lambert, J.A.; Gilston, P.F.

1989-08-01

A preliminary assessment has been carried out to determine the suitability of the hot wire tungsten inert gas (TIG) welding process for the repair of thick section, ferritic steel nuclear pressure vessels. The objective has been to identify a hot wire TIG temper bead procedure, suitable for repairs without post weld heat treatment. This procedure involves depositing two weld layers with carefully selected welding parameters such that overlapping thermal cycles produce a refined and tempered heat affected zone, HAZ, microstructure. (author)

Simulation of deep penetration welding of stainless steel using geometric constraints based on experimental information

International Nuclear Information System (INIS)

Milewski, J.O.; Lambrakos, S.G.

1995-01-01

This report presents a general overview of a method of numerically modelling deep penetration welding processes using geometric constraints based on boundary information obtained from experiment. General issues are considered concerning accurate numerical calculation of temperature and velocity fields in regions of the meltpool where the flow of fluid is characterized by quasi-stationary Stokes flow. It is this region of the meltpool which is closest to the heat-affected-zone (HAZ) and which represents a significant fraction of the fusion zone (FZ)

Influence des traitements thermiques à haute température sur l'évolution de la texture et de la microstructure des soudures d'acier inoxydable duplex 2205

OpenAIRE

Badji , Riad

2008-01-01

This work deals with the study of the texture and microstructure evolution during welding and subsequent annealing treatment of 2205 duplex stainless steel. Microstructural examination showed the presence of higher ferrite amount in the heat affected zone (HAZ), while higher amount of austenite was recorded in the centre region of the weld metal. Annealing treatment at temperature range of 800-1000°C resulted in a precipitation of σ phase and M23C6 chromium carbides at the γ/δ interfaces that...

Effect of heating produced by welding on the microstructure and on the stress corrosion cracking susceptibility of AA7028 alloy

International Nuclear Information System (INIS)

Calatayud, A.; Rodenas, M.; Ferrer, C.; Amigo, V.; Salvador, M.D.

1997-01-01

The microstructural and stress corrosion cracking changes due to welding are studied for the AA7028 aluminium alloy. Special attention is paid to the characterization of what is known as the white zone. The influence of the delay step between quenching and aging in a T73 treatment on the microstructure and on the characteristics of the heat-affected zone (HAZ) is also studied. Finally the effect of thermal treatments applied on this zone after the welding is analysed. (Author) 7 refs

The biogas potential from municipal waste and agricultural residues in Hazaribagh, Dhaka city, Bangladesh : - a possible strategy to improve the energy system

OpenAIRE

Hasan, A S M Monjurul

2016-01-01

Energy is considered as the foremost significant factor towards socio-economic growth. Due to the rapid growth of industrialization in Bangladesh, the need of energy is increasing day by day. Considering the environmental issues, sustainable solutions are needed to address the energy crisis. Energy generation from waste through biogas can be a good solution that can address both the energy demand as well as the waste management issue.    The overall aim of this master thesis is to analyze Haz...

Body Composition and Catch-up in Height after Treatment of Malnourished Children

International Nuclear Information System (INIS)

Badaloo, Asha; Morris, Richard; Forrester, Terrence; Reid, Marvin; Wootton, Steve; Jackson, Alan

2014-01-01

Full text: Background and Objectives: The use of enriched diets to promote rapid catch-up-growth and the delay in catch-up in length/height relative to catch-up in weight may be associated with excess adiposity and poor lean tissue deposition. We aimed to assess lean mass (LM) during treatment of Jamaican malnourished children and to investigate if stunted malnourished children remained stunted as adults. Methods: All participants were managed in hospital and in accordance with WHO guidelines. Diagnosis (marasmus, kwashiorkor, marasmic-kwashiorkor) was based on the Welcome Classification. LM was estimated from total body water(TBW)in 44 children (group 1), aged 3 to 32 months, during the stabilization period, mid catch-up growth and on achieving at least 90% of reference weight-for-length using deuterium dilution technique. Length-for-age (LAZ) and height-for-age (HAZ) Z-scores were determined in another group of 168 malnourished children (group 2) on admission, aged 3 to 33 months, and when they attained adulthood. LAZ was calculated using recent WHO child growth standards. Results: Data are mean ± SD. The participants included moderately and severely malnourished children based on weight-for-length Z-score (WLZ). In group 1, after initial stabilization intake increased to 685 ± 101 kJ/kg/d and 3.7 ± 0.6 g protein/kg/d resulting in rapid weight gain (16.5 ± 5.1 g/kg/d) and catch-up in weight over 20 ± 10 d. Consequently, WLZ at admission (non-oedematous: -3.0 ± 0.2; oedematous: -2.1 ± 0.2) improved to -0.48 ± 0.2. At recovery in weight, LM was consistent with reported values in normal children (71% to 92 % of body weight and 11 to 15 kg/m2) but the children remained stunted (LAZ: -3.3 ± 3.2). Insecurity of TBW measurement and estimating LM in the acute malnourished state and during rapid growth limits the ability to capture changes in lean and fat during rehabilitation. Similar to group 1, WLZ in group 2 was -3.2 ± 1.3 on admission; -0.6 ± 1 at recovery

Microstructural evolution in the HAZ of Inconel 718 and correlation with the hot ductility test

Science.gov (United States)

Thompson, R. G.; Genculu, S.

1983-01-01

The nickel-base alloy 718 was evaluated to study the role of preweld heat treatment in reducing or eliminating heat-affected zone hot cracking. Three heat treatments were studied using the Gleeble hot ductility test. A modified hot ductility test was also used to follow the evolution of microstructure during simulated welding thermal cycles. The microstructural evolution was correlated with the hot ductility data in order to evaluate the mechanism of hot cracking in alloy 718. The correlation of hot ductility with microstructure showed that recrystallization, grain growth, and dissolution of precipitates did not in themselves cause any loss of ductility during cooling. Ductility loss during cooling was not initiated until the constitutional liquation of NbC particles was observed in the microstructure. Laves-type phases were found precipitated in the solidified grain boundaries but were not found to correlate with any ductility loss parameter. Mechanisms are reviewed which help to explain how heat treatment controls the hot crack susceptibility of alloy 718 as measured in the hot ductility test.

T.I.G. Welding of stainless steel. Numerical modelling for temperatures calculation in the Haz

International Nuclear Information System (INIS)

Martinez-Conesa, E. J.; Estrems-Amestoy, M.; Miguel-Eguia, V.; Garrido-Hernandez, A.; Guillen-Martinez, J. A.

2010-01-01

In this work, a numerical method for calculating the temperature field into the heat affected zone for butt welded joints is presented. The method has been developed for sheet welding and takes into account a bidimensional heat flow. It has built a computer program by MS-Excel books and Visual Basic for Applications (VBA). The model has been applied to the TIG process of AISI 304 stainless steel 2mm thickness sheet. The welding process has been considered without input materials. The numerical method may be used to help the designers to predict the temperature distribution in welded joints. (Author) 12 refs.

Proton external beam in the TANDAR Accelerator; Haz externo de protones en el acelerador TANDAR

Energy Technology Data Exchange (ETDEWEB)

Rey, R; Schuff, J A; Perez de la Hoz, A.; Debray, M E; Hojman, D; Kreiner, A J; Kesque, J M; Saint-Martin, G; Oppezzo, O; Bernaola, O A; Molinari, B L; Duran, H A; Policastro, L; Palmieri, M; Ibanez, J; Stoliar, P; Mazal, A; Caraballo, M E; Burlon, A; Cardona, M A; Vazquez, M E; Salfity, M F; Ozafran, M J; Naab, F; Levinton, G; Davidson, M; Buhler, M [Departamento de Fisica, Comision Nacional de Energia Atomica, Av. Gral. Paz 1499, C.P. 1650 San Martin, Buenos Aires (Argentina)

1999-12-31

An external proton beam has been obtained in the TANDAR accelerator with radiological and biomedical purposes. The protons have excellent physical properties for their use in radiotherapy allowing a very good accuracy in the dose spatial distribution inside the tissue so in the side direction as in depth owing to the presence of Bragg curve. The advantage of the accuracy in the dose localization with proton therapy is good documented (M. Wagner, Med. Phys. 9, 749 (1982); M. Goitein and F. Chen, Med. Phys. 10, 831 (1983); M.R. Raju, Rad. Res. 145, 391 (1996)). It was obtained external proton beams with energies between 15-25 MeV, currents between 2-10 p A and a uniform transversal sections of 40 mm{sup 2} approximately. It was realized dosimetric evaluations with CR39 and Makrofol foliation. The irradiations over biological material contained experiences In vivo with laboratory animals, cellular and bacterial crops. It was fixed the optimal conditions of position and immobilization of the Wistar rats breeding for the In vivo studies. It was chosen dilutions and sowing techniques adequate for the exposition at the cellular and bacterial crops beam. (Author)

Proton external beam in the TANDAR Accelerator; Haz externo de protones en el acelerador TANDAR

Energy Technology Data Exchange (ETDEWEB)

Rey, R.; Schuff, J.A.; Perez de la Hoz, A.; Debray, M.E.; Hojman, D.; Kreiner, A.J.; Kesque, J.M.; Saint-Martin, G.; Oppezzo, O.; Bernaola, O.A.; Molinari, B.L.; Duran, H.A.; Policastro, L.; Palmieri, M.; Ibanez, J.; Stoliar, P.; Mazal, A.; Caraballo, M.E.; Burlon, A.; Cardona, M.A.; Vazquez, M.E.; Salfity, M.F.; Ozafran, M.J.; Naab, F.; Levinton, G.; Davidson, M.; Buhler, M. [Departamento de Fisica, Comision Nacional de Energia Atomica, Av. Gral. Paz 1499, C.P. 1650 San Martin, Buenos Aires (Argentina)

1998-12-31

An external proton beam has been obtained in the TANDAR accelerator with radiological and biomedical purposes. The protons have excellent physical properties for their use in radiotherapy allowing a very good accuracy in the dose spatial distribution inside the tissue so in the side direction as in depth owing to the presence of Bragg curve. The advantage of the accuracy in the dose localization with proton therapy is good documented (M. Wagner, Med. Phys. 9, 749 (1982); M. Goitein and F. Chen, Med. Phys. 10, 831 (1983); M.R. Raju, Rad. Res. 145, 391 (1996)). It was obtained external proton beams with energies between 15-25 MeV, currents between 2-10 p A and a uniform transversal sections of 40 mm{sup 2} approximately. It was realized dosimetric evaluations with CR39 and Makrofol foliation. The irradiations over biological material contained experiences In vivo with laboratory animals, cellular and bacterial crops. It was fixed the optimal conditions of position and immobilization of the Wistar rats breeding for the In vivo studies. It was chosen dilutions and sowing techniques adequate for the exposition at the cellular and bacterial crops beam. (Author)

TEM Study of SAFARI-2000 Aerosols

Science.gov (United States)

Buseck, Peter R.

2004-01-01

The aim of our research was to obtain data on the chemical and physical properties of individual aerosol particles from biomass smoke plume s in southern Africa and from air masses in the region that are affec ted by the smoke. We used analytical transmission electron microscopy (ATEM), including energy-dispersive X-ray spectrometry (EDS) and ele ctron energy-loss spectroscopy (EELS), and field-emission electron microscopy (FESEM) to study aerosol particles from several smoke and haz e samples and from a set of cloud samples.