WorldWideScience

Sample records for harvest yield high

  1. Harvester development for new high yielding SRC crops and markets

    International Nuclear Information System (INIS)

    2005-12-01

    Details are given of a project to develop a harvesting system that can produce fuel economically in a single pass to a required specification at a cost that is profitable for the grower while minimising the cost of the product. The project objectives listed include the development of a harvester drive chain and feeding systems to allow harvesting of the higher yielding crops now produced in the UK, determination of the most economic harvesting cycle for SRC crops, and production of fuels suitable for co-firing with coal in pulverised fuel systems or for gasification. The work programme and project conclusions are discussed

  2. Harvester development for new high yielding SRC crops and markets

    Energy Technology Data Exchange (ETDEWEB)

    Paulson, Mark

    2005-07-01

    This report describes the development of harvesting equipment for short rotation cultivation (SRC) crops produced in the UK that can produce fuel to a required specification in a single pass at a cost that is profitable for the grower while minimising the cost of the product. Details are given of the manufacture and installation of new components for large crop harvesting, and production of fuel suitable for co-firing in a coal combustion system using pulverised fuel and fuel suitable for gasification. The development of the drive chain to cope with the higher yielding crops, field tests on SRC crops, and determination of the most economic harvesting system are discussed along with the remanufacture of the chipping drum, and production of market chip samples. Harvesting guidance and an economic analysis of harvesting systems are presented.

  3. Harvester development for new high yielding SRC crops and markets

    International Nuclear Information System (INIS)

    Paulson, Mark

    2005-01-01

    This report describes the development of harvesting equipment for short rotation cultivation (SRC) crops produced in the UK that can produce fuel to a required specification in a single pass at a cost that is profitable for the grower while minimising the cost of the product. Details are given of the manufacture and installation of new components for large crop harvesting, and production of fuel suitable for co-firing in a coal combustion system using pulverised fuel and fuel suitable for gasification. The development of the drive chain to cope with the higher yielding crops, field tests on SRC crops, and determination of the most economic harvesting system are discussed along with the remanufacture of the chipping drum, and production of market chip samples. Harvesting guidance and an economic analysis of harvesting systems are presented

  4. Homogeneity analysis of high yield manufacturing process of mems-based pzt thick film vibrational energy harvesters

    DEFF Research Database (Denmark)

    Lei, Anders; Xu, Ruichao; Pedersen, C.M.

    2011-01-01

    This work presents a high yield wafer scale fabrication of MEMS-based unimorph silicon/PZT thick film vibrational energy harvesters aimed towards vibration sources with peak frequencies in the range of a few hundred Hz. By combining KOH etching with mechanical front side protection, SOI wafer...... to accurately define the thickness of the silicon part of the harvester and a silicon compatible PZT thick film screen-printing technique, we are able to fabricate energy harvesters on wafer scale with a yield higher than 90%. The characterization of the fabricated harvesters is focused towards the full wafer....../mass-production aspect; hence the analysis of uniformity in harvested power and resonant frequency....

  5. Influence of planting and harvesting dates on sweet potato yield ...

    African Journals Online (AJOL)

    home

    Two experiments were conducted to study the influence of harvesting date on three sweet potato ... determining whole top yields above ground level. .... plant storage organ (which in this case is the root) prior to harvesting and processing for.

  6. High Harvest Yield, High Expansion, and Phenotype Stability of CD146 Mesenchymal Stromal Cells from Whole Primitive Human Umbilical Cord Tissue

    Directory of Open Access Journals (Sweden)

    Rebecca C. Schugar

    2009-01-01

    Full Text Available Human umbilical cord blood is an excellent primitive source of noncontroversial stem cells for treatment of hematologic disorders; meanwhile, new stem cell candidates in the umbilical cord (UC tissue could provide therapeutic cells for nonhematologic disorders. We show novel in situ characterization to identify and localize a panel of some markers expressed by mesenchymal stromal cells (MSCs; CD44, CD105, CD73, CD90 and CD146 in the UC. We describe enzymatic isolation and purification methods of different UC cell populations that do not require manual separation of the vessels and stroma of the coiled, helical-like UC tissue. Unique quantitation of in situ cell frequency and stromal cell counts upon harvest illustrate the potential to obtain high numerical yields with these methods. UC stromal cells can differentiate to the osteogenic and chondrogenic lineages and, under specific culturing conditions, they exhibit high expandability with unique long-term stability of their phenotype. The remarkable stability of the phenotype represents a novel finding for human MSCs, from any source, and supports the use of these cells as highly accessible stromal cells for both basic studies and potentially therapeutic applications such as allogeneic clinical use for musculoskeletal disorders.

  7. High yielding tropical energy crops for bioenergy production: Effects of plant components, harvest years and locations on biomass composition.

    Science.gov (United States)

    Surendra, K C; Ogoshi, Richard; Zaleski, Halina M; Hashimoto, Andrew G; Khanal, Samir Kumar

    2018-03-01

    The composition of lignocellulosic feedstock, which depends on crop type, crop management, locations and plant parts, significantly affects the conversion efficiency of biomass into biofuels and biobased products. Thus, this study examined the composition of different parts of two high yielding tropical energy crops, Energycane and Napier grass, collected across three locations and years. Significantly higher fiber content was found in the leaves of Energycane than stems, while fiber content was significantly higher in the stems than the leaves of Napier grass. Similarly, fiber content was higher in Napier grass than Energycane. Due to significant differences in biomass composition between the plant parts within a crop type, neither biological conversion, including anaerobic digestion, nor thermochemical pretreatment alone is likely to efficiently convert biomass components into biofuels and biobased products. However, combination of anaerobic digestion with thermochemical conversion technologies could efficiently utilize biomass components in generating biofuels and biobased products. Copyright © 2017 Elsevier Ltd. All rights reserved.

  8. Effect of harvesting techniques on cumulative yields of huckleberry ...

    African Journals Online (AJOL)

    ... of huckleberry (Solanum scabrum) in the humid forest region of Cameroon. ... However, despite their relative importance, information on their management is ... first harvest on the subsequent fresh and dry shoot yields of Solanum scabrum.

  9. Fiber optic yield monitor for a sugarcane chopper harvester

    Science.gov (United States)

    A fiber optic yield monitoring system was developed for a sugarcane chopper harvester that utilizes a duty-cycle type approach with three fiber optic sensors mounted in the elevator floor to estimate cane yield. Field testing of the monitor demonstrated that there was a linear relationship between t...

  10. Identifying yield-optimizing environments for two cowpea breeding lines by manipulating photoperiod and harvest scenario

    Science.gov (United States)

    Ohler, T. A.; Mitchell, C. A.

    1996-01-01

    Photoperiod and harvest scenario of cowpea (Vigna unguiculata L. Walp) canopies were manipulated to optimize productivity for use in future controlled ecological life-support systems. Productivity was measured by edible yield rate (EYR:g m-2 day-1), shoot harvest index (SHI: g edible biomass [g total shoot dry weight]), and yield-efficiency rate (YER:g edible biomass m-2 day-1 per[g nonedible shoot dry weight]). Breeding lines 'IT84S-2246' (S-2246) and "IT82D-889' (D-889) were grown in a greenhouse under 8-, 12-, or 24-h photoperiods. S-2246 was short-day and D-889 was day-neutral for flowering. Under each photoperiod, cowpeas were harvested either for leaves only, seeds only, or leaves plus seeds (mixed harvest). Photoperiod did not affect EYR of either breeding line for any harvest scenario tested. Averaged over both breeding lines, seed harvest gave the highest EYR at 6.7 g m-2 day-1. The highest SHI (65%) and YER (94 mg m-2 day-1 g-1) were achieved for leaf-only harvest of D-889 under an 8-h photoperiod. For leaf-only harvest of S-2246, both SHI and YER increased with increasing photoperiod, but declined for seed-only and mixed harvests. However, photoperiod had no effect on SHI or YER for D-889 for any harvest scenario. A second experiment utilized the short-day cowpea breeding line 'IT89KD-288' (D-288) and the day-neutral breeding line 'IT87D-941-1' (D-941) to compare yield parameters using photoperiod extension under differing lamp types. This experiment confirmed the photoperiod responses of D-889 and S-2246 to a mixed-harvest scenario and indicated that daylength extension with higher irradiance from high pressure sodium lamps further suppressed EYR, SHI, and YER of the short-day breeding line D-288.

  11. The Impact of Harvest Frequency on Herbage Yield and Quality of ...

    African Journals Online (AJOL)

    User

    This can be achieved by maximising forage production through appropriate harvest management .... seasons and T1 was to estimate DM yield if sward remains undisturbed until the ... was the above ground biomass yield (ton ha-1). Harvested ...

  12. Anaerobic digestion of industrial hemp-effect of harvest time on methane energy yield per hectare

    Energy Technology Data Exchange (ETDEWEB)

    Kreuger, E; Escobar, F; Bjoernsson, L [Department of Biotechnology, Lund University, P.O. Box 124, SE-221 00 Lund (Sweden); Prade, T; Svensson, S -E; Englund, J -E [Department of Agriculture-Farming Systems, Technology and Product Quality, Swedish University of Agricultural Sciences, P.O. Box 104, SE-230 53 Alnarp (Sweden)

    2011-02-15

    There is a worldwide emphasis to increase the share of renewable transportation fuels. When using agricultural land for production of renewable transportation fuels, the energy output per hectare for different crops and transportation fuels is a crucial factor. In this study, the gross methane energy yield per hectare from anaerobic digestion of industrial hemp (Cannabis sativa L.), was determined at four different harvest times between July and October in Southern Sweden, a cold climate region. The biomass yield was determined for three years and the methane yield was determined for two years through the biochemical methane potential test. The highest biomass yield, 16 tonnes dry matter per hectare on an average, and the highest methane energy yield per hectare was achieved when the hemp was harvested in September or October, with an average gross methane energy yield of 136 {+-} 24 GJ per hectare. There was no significant difference in the specific methane yield between the harvest times; the average being 234 {+-} 35 m{sup 3} per tonne volatile solids. Biogas from hemp turned out to be a high yielding alternative to the currently dominating renewable transportation fuels produced from crops grown in Sweden: ethanol from wheat and biodiesel from rapeseed. (author)

  13. Chemical composition and methane yield of reed canary grass as influenced by harvesting time and harvest frequency

    DEFF Research Database (Denmark)

    Kandel, Tanka Prasad; Sutaryo, Sutaryo; Møller, Henrik Bjarne

    2013-01-01

    This study examined the influence of harvest time on biomass yield, dry matter partitioning, biochemical composition and biological methane potential of reed canary grass harvested twice a month in one-cut (OC) management. The regrowth of biomass harvested in summer was also harvested in autumn...... as a two-cut management with (TC-F) or without (TC-U) fertilization after summer harvest. The specific methane yields decreased significantly with crop maturity that ranged from 384 to 315 and from 412 to 283 NL (normal litre) (kg VS)-1 for leaf and stem, respectively. Approximately 45% more methane...... was produced by the TC-F management (5430 Nm3 ha-1) as by the OC management (3735 Nm3 ha-1). Specific methane yield was moderately correlated with the concentrations of fibre components in the biomass. Larger quantity of biogas produced at the beginning of the biogas assay from early harvested biomass...

  14. Predicted harvest time effects on switchgrass moisture content, nutrient concentration, yield, and profitability

    Science.gov (United States)

    Production costs change with harvest date of switchgrass (Panicum virgatum L.) as a result of nutrient recycling and changes in yield of this perennial crop. This study examines the range of cost of production from an early, yield-maximizing harvest date to a late winter harvest date at low moisture...

  15. Simultaneous harvesting of straw and chaff for energy purposes : influence on bale density, yield, field drying process and combustion characteristics

    Energy Technology Data Exchange (ETDEWEB)

    Lundin, G. [JTI Swedish Inst. of Agricultural and Environmental Engineering, Uppsala (Sweden); Ronnback, M. [SP Technical Research Inst. of Sweden, Boras (Sweden)

    2010-07-01

    The potential to increase the productivity of fuel straw harvest and transportation was examined. When harvesting straw for energy purposes, only the long fraction is currently collected. However, technological improvements have now rendered it possible to harvest chaff, thus increasing the amount of harvest residues and bale density. The purpose of this study was to determine how harvest yield, bale density, field-drying behaviour and combustion characteristics are affected by the simultaneous harvest of straw and chaff. Field experiments were conducted in 2009 for long- and short-stalked winter wheat crops. Combine harvesting was carried out with 2 different types of combine harvesters. A high-density baler was used to bale the crop residues. Mixing chaff in with the straw swath by combine harvesting gave a lower initial moisture content compared with straw only. The density and the weight of each bale were not affected by the treatments. However, the added chaff increased the total yield of crop residues by 14 per cent, indicating that about half of the biologically available chaff was harvested. Although mixing in chaff increased the ash content by 1 percentage unit, there was no considerable change in net calorific value or ash melting behaviour.

  16. Harvesting Method Affects Water Dynamics and Yield of Sweet Orange with Huanglongbing

    Directory of Open Access Journals (Sweden)

    Said A. Hamido

    2018-03-01

    Full Text Available Changes in grove management practices may change crop water dynamics. The objective of this study was to estimate sap flow, stem water potential (Ψstem, and citrus yield as affected by harvesting methods in sweet orange (Citrus sinensis trees affected by Huanglongbing. The study was initiated in March 2015 for two years on five-year-old commercial sweet orange trees at a commercial grove located at Felda, Florida (26.61° N, 81.48° W on Felda fine sand soil (Loamy, siliceous, superactive, hyperthermic Arenic Endoaqualfs. All measurements were replicated before and after harvest in four experiments (A, B, C and D under hand and mechanical harvesting treatments. Sap flow measurements were taken on four trees per treatment with two sensors per tree. Sap flow measured by the heat balance method at hourly intervals during March and April of 2015 and 2016 significantly declined after harvesting by 25% and 35% after hand and mechanical harvesting, respectively. Ψstem measured after harvest was significantly higher than measurements before harvest. The average value of Ψstem measured increased by 10% and 6% after hand and mechanical harvesting, respectively. Mechanical harvesting exhibited lower fruit yields that averaged between 83%, 63%, 49% and 36% of hand-harvested trees under A, B, C and D experiments, respectively. It is concluded that the hand harvesting method is less stressful and less impactful on tree water uptake and fruit yield compared with mechanical harvesting.

  17. Chemical composition and methane yield of reed canary grass as influenced by harvesting time and harvest frequency.

    Science.gov (United States)

    Kandel, Tanka P; Sutaryo, Sutaryo; Møller, Henrik B; Jørgensen, Uffe; Lærke, Poul E

    2013-02-01

    This study examined the influence of harvest time on biomass yield, dry matter partitioning, biochemical composition and biological methane potential of reed canary grass harvested twice a month in one-cut (OC) management. The regrowth of biomass harvested in summer was also harvested in autumn as a two-cut management with (TC-F) or without (TC-U) fertilization after summer harvest. The specific methane yields decreased significantly with crop maturity that ranged from 384 to 315 and from 412 to 283 NL (normal litre) (kgVS)(-1) for leaf and stem, respectively. Approximately 45% more methane was produced by the TC-F management (5430Nm(3)ha(-1)) as by the OC management (3735Nm(3)ha(-1)). Specific methane yield was moderately correlated with the concentrations of fibre components in the biomass. Larger quantity of biogas produced at the beginning of the biogas assay from early harvested biomass was to some extent off-set by lower concentration of methane. Copyright © 2012 Elsevier Ltd. All rights reserved.

  18. Effect of harvest methods on yield and quality of Marketable flowers ...

    African Journals Online (AJOL)

    This study was carried out to determine the effects of harvest methods (proximal and median harvests) on yield and quality of marketable flowers of greenhouse hybrid tea rose (Rosa hybrida L.) cultivars of different growth habits. The cultivar Grant Galla represented cultivars of vigorous growth habit whereas 'Vivaldi' ...

  19. The Impact of Location and Growing Medium on Harvest Yield and Flavor of Basil and Squash Microgreens

    Science.gov (United States)

    Leal, J.; Ventura, C. J.

    2016-12-01

    The purpose of this experiment is to discover the most efficient, feasible way to produce a high yield of flavorful microgreens within the best growing medium and building location at the Stanford Educational Farm. In recent years, microgreens, young, small edible greens utilized as flavor garnishes for fine dining, have evolved into an immensely profitable market that will continue to expand and prosper. To capitalize on such opportunities, the primary metrics focused upon are harvest yield and flavor of basil and squash microgreens, as they develop in different concentrations of quick root and compost while located in either a greenhouse or lath house. It was hypothesized that if basil and squash microgreens were grown in a mixture of 50% compost and 50% quick root in the greenhouse, then they would produce the greatest harvest yield and maximum amount of flavor. The general experimental protocol includes monitoring the growth of the microgreens, then harvesting directly after the first true leaves begin to emerge. Upon harvest, each set of microgreens are separated into different clear glass jars to place on a small scale for weighing to determine the yield and tasting the leaves to analyze the flavor content. The highest yield of basil (63 grams) developed in a tray of 100% quick root in the lath house, while the greatest yield of squash (51 grams) succeeded in 100% quick root in the greenhouse. Overall however, the basil grew fastest in the greenhouse but tasted stronger in the lath house. Additionally, because the harvest yield and flavor results were so poor in all other locations and growing mediums for squash during the first trial, it cannot be considered a viable microgreen. In the future, more trials should be conducted for greater numbers of trays of microgreens to collect more data. The nutritional value of microgreens should also be explored further to obtain a holistic approach to the value of these plants from seed to harvest to consumption.

  20. Varying plant density and harvest time to optimize cowpea leaf yield and nutrient content

    Science.gov (United States)

    Ohler, T. A.; Nielsen, S. S.; Mitchell, C. A.

    1996-01-01

    Plant density and harvest time were manipulated to optimize vegetative (foliar) productivity of cowpea [Vigna unguiculata (L.) Walp.] canopies for future dietary use in controlled ecological life-support systems as vegetables or salad greens. Productivity was measured as total shoot and edible dry weights (DW), edible yield rate [(EYR) grams DW per square meter per day], shoot harvest index [(SHI) grams DW per edible gram DW total shoot], and yield-efficiency rate [(YER) grams DW edible per square meter per day per grams DW nonedible]. Cowpeas were grown in a greenhouse for leaf-only harvest at 14, 28, 42, 56, 84, or 99 plants/m2 and were harvested 20, 30, 40, or 50 days after planting (DAP). Shoot and edible dry weights increased as plant density and time to harvest increased. A maximum of 1189 g shoot DW/m2 and 594 g edible DW/m2 were achieved at an estimated plant density of 85 plants/m2 and harvest 50 DAP. EYR also increased as plant density and time to harvest increased. An EYR of 11 g m-2 day-1 was predicted to occur at 86 plants/m2 and harvest 50 DAP. SHI and YER were not affected by plant density. However, the highest values of SHI (64%) and YER (1.3 g m-2 day-1 g-1) were attained when cowpeas were harvested 20 DAP. The average fat and ash contents [dry-weight basis (dwb)] of harvested leaves remained constant regardless of harvest time. Average protein content increased from 25% DW at 30 DAP to 45% DW at 50 DAP. Carbohydrate content declined from 50% DW at 30 DAP to 45% DW at 50 DAP. Total dietary fiber content (dwb) of the leaves increased from 19% to 26% as time to harvest increased from 20 to 50 days.

  1. Corn stover harvest strategy effects on grain yield and soil quality indicators

    International Nuclear Information System (INIS)

    Douglas, K.; Stuart, B.; Adam, W.

    2013-01-01

    Developing strategies to collect and use cellulo sic biomass for bio energy production is important because those materials are not used as human food sources. This study compared corn (Zea mays L.) stover harvest strategies on a 50 ha Clarion- Nicol let-Webster soil Association site near Emmetsburg, Iowa, USA. Surface soil samples (0 to 15 cm) were analyzed after each harvest to monitor soil organic carbon (Soc), ph, phosphorus (P) and potassium (K) changes. Grain yields in 2008, before the stover harvest treatments were imposed, averaged 11.4 Mg ha-1. In 2009, 2010, and 2011 grain yields averaged 10.1, 9.7, and 9.5 Mg ha-1, respectively. Although grain yields after stover harvest strategies imposed were lower than in 2008, there were no significant differences among the treatments. Four-year average stover collection rates ranged 1.0 to 5.2 Mg ha-1 which was 12 to 60% of the above-ground biomass. Soc showed a slight decrease during the study, but the change was not related to any specific stover harvest treatment. Instead, we attribute the Soc decline to the tillage intensity and lower than expected crop yields. Overall, these results are consistent with other Midwestern USA studies that indicate corn stover should not be harvested if average grain yields are less than 11 Mg ha-1

  2. Sensitivity of TRIM projections to management, harvest, yield, and stocking adjustment assumptions.

    Science.gov (United States)

    Susan J. Alexander

    1991-01-01

    The Timber Resource Inventory Model (TRIM) was used to make several projections of forest industry timber supply for the Douglas-fir region. The sensitivity of these projections to assumptions about management and yields is discussed. A base run is compared to runs in which yields were altered, stocking adjustment was eliminated, harvest assumptions were changed, and...

  3. Effect of Harvest Time and Nitrogen Doses on Cassava Root Yield and Quality

    Directory of Open Access Journals (Sweden)

    Natália Trajano de Oliveira

    Full Text Available ABSTRACT Nitrogen is considered the most limiting nutrient for cassava, and N availability can influence the crop cycle, including earlier harvest. The aim of this study was to study the effect of harvest time on the production components of cassava, “Aciolina” cultivar, at different rates of N fertiliser. The experiment was carried out in an area newly incorporated into the productive system in a savannah ecosystem in the northern Amazon. A randomised block experimental design was used in a split plot arrangement with four replications. The N rates (0, 30, 60, 150, and 330 kg ha-1 were allocated to the main plots, and the harvest times (90, 120, 150, 180, 240, 300, and 360 days after emergence of the stalks - DAE were allocated to the subplots. Plant height, shoot fresh matter yield, number of roots per plant, average root diameter, and root fresh matter yield display an increasing linear response up to 360 DAE in cassava cv. “Aciolina”. For all harvest times, the N rates promote an increase in root fresh matter yield. At 300 and 360 DAE, the root fresh matter and starch yield and the harvest index show a quadratic response as a function of the N level. The greatest efficiency of N topdressing on the production of root fresh matter occurs at 300 DAE, promoting an earlier harvest. At that time, the dose of maximum technical efficiency, 226 kg ha-1 N, results in a yield of 62 Mg ha-1 of root fresh matter, 13 Mg ha-1 of starch, and a harvest index of 81 %.

  4. Harvest season and head rice yield of upland rice cultivars submitted to parboiling

    Directory of Open Access Journals (Sweden)

    Diva Mendonça Garcia

    2012-11-01

    Full Text Available Normal 0 21 false false false PT-BR X-NONE X-NONE This work aimed to evaluate the effects of parboiling on the yield of upland rice cultivars harvested at different times. The cultivars were BRS Primavera and BRS Sertaneja, harvested at 30 and 47 days after flowering (DAF. For parboiling, samples were soaked in water bath at 65 °C in grain: water ratio of 1:1.6 in order to reach 25% and 30% moisture, and then were autoclaved for 10 minutes at 120 °C and 1.1 kg/cm2 of pressure. After drying up to 13% moisture in a greenhouse with forced air at 40 °C, samples were benefited, followed by separation using the trieur equipment and weighing to obtain the head rice yield. The results showed a higher yield for head rice harvested at 30 DAF than at 47 DAF (BRS Primavera 63.2 and 38.7%; BRS Sertaneja 68.5 and 55.7%, respectively. Parboiling increased the head rice yield, regardless of harvest season, but partly reflected the potential of the cultivar origin: BRS Primavera 70.06%, BRS Sertaneja 74.94%. It is concluded that the harvest season is one of the factors that most influence the quality of industrial rice and the effect of parboiling also depends on the potential of the material source.

  5. Ecological dynamics of age selective harvesting of fish population: Maximum sustainable yield and its control strategy

    International Nuclear Information System (INIS)

    Jana, Debaldev; Agrawal, Rashmi; Upadhyay, Ranjit Kumar; Samanta, G.P.

    2016-01-01

    Highlights: • Age-selective harvesting of prey and predator are considered by multi-delayed prey-predator system. • System experiences stable coexistence to oscillatory mode and vice versa via Hopf-bifurcation depending upon the parametric restrictions. • MSY, bionomic equilibrium and optimal harvesting policy are also depending upon the age-selection of prey and predator. • All the analytic results are delay dependent. • Numerical examples support the analytical findings. - Abstract: Life history of ecological resource management and empirical studies are increasingly documenting the impact of selective harvesting process on the evolutionary stable strategy of both aquatic and terrestrial ecosystems. In the present study, the interaction between population and their independent and combined selective harvesting are framed by a multi-delayed prey-predator system. Depending upon the age selection strategy, system experiences stable coexistence to oscillatory mode and vice versa via Hopf-bifurcation. Economic evolution of the system which is mainly featured by maximum sustainable yield (MSY), bionomic equilibrium and optimal harvesting vary largely with the commensurate age selections of both population because equilibrium population abundance becomes age-selection dependent. Our study indicates that balance between harvesting delays and harvesting intensities should be maintained for better ecosystem management. Numerical examples support the analytical findings.

  6. Impact of harvesting time on ultimate methane yield of switchgrass grown in eastern Canada

    Energy Technology Data Exchange (ETDEWEB)

    Gilbert, Y.; Masse, D. [Agriculture and Agri-Food Canada, Sherbrooke, PQ (Canada). Dairy and Swine Research and Development Centre; Savoie, P.; Belanger, G.; Parent, G. [Agriculture and Agri-Food Canada, Quebec City, PQ (Canada). Soils and Crops Research and Development Centre; Babineau, D.L. [Groupe EBI, Berthierville, PQ (Canada)

    2010-07-01

    European research in green energy production from crops has resulted in the development of full scale bioreactors that use energy crops as feedstock. Switchgrass has been touted as one of the most promising crops for energy production among several perennial grass species grown under moderate to hot climates. However, few studies have been conducted in colder climate conditions. This study examined the mesophilic methane yield of switchgrass grown under the cooler growing conditions that exist in northeastern North America. In 2007, switchgrass was harvested in late July, August and September and conserved as silage. The regrowth of plots harvested in late July was also harvested in late September as a two-cut strategy. A 30 L small-scale laboratory digester was used to anaerobically digest the switchgrass silage samples. Specific methane yield decreased considerably with advancing plant development, but was similar between the first harvest in late July and the regrowth in late September. Nearly 25 per cent more methane could be produced by hectare for the two-cut strategy compared to harvesting once in late August. It was concluded that additional studies are needed to determine the effect of cutting times and strategies on the long term yield of switchgrass and to establish the production cost of this renewable energy.

  7. Switchgrass, Bermudagrass, Flaccidgrass, and Lovegrass biomass yield response to nitrogen for single and double harvest

    International Nuclear Information System (INIS)

    Aravindhakshan, Sijesh C.; Epplin, Francis M.; Taliaferro, Charles M.

    2011-01-01

    Switchgrass (Panicum virgatum) has been identified as a model dedicated energy crop species. After a perennial grass is established, the major variable costs are for nitrogen (N) fertilizer and harvest. Prior to establishing switchgrass on millions of ha in a particular agro-climatic region, it would be useful to determine switchgrass yield response to N and its response to harvest frequency relative to alternative grass species. The objective of this research is to determine biomass yield response to N for four perennial grass species and to determine the species, N level, and harvest frequency that will maximize expected net returns, given the climate and soils of the U.S.A. Southern Plains. Yield data were produced in an experiment that includes four species (switchgrass, bermudagrass (Cynodon dactylon), weeping lovegrass (Eragrostis curvula), and carostan flaccidgrass (Pennisetum flaccidum)), four N levels, and two harvest levels. Linear response plateau (LRP), linear response stochastic plateau (LRSP), and quadratic response (QR) functions are estimated. For all combinations of biomass and N prices considered, the optimal species is switchgrass. For most price situations, it is economically optimal to fertilize established stands of switchgrass with 69 kg N ha -1 yr -1 and to harvest once yr -1 after senescence.

  8. Switchgrass, Bermudagrass, Flaccidgrass, and Lovegrass biomass yield response to nitrogen for single and double harvest

    Energy Technology Data Exchange (ETDEWEB)

    Aravindhakshan, Sijesh C.; Epplin, Francis M. [Department of Agricultural Economics, Oklahoma State University, Stillwater, OK 74078-6026 (United States); Taliaferro, Charles M. [Department of Plant and Soil Sciences, Oklahoma State University, Stillwater, OK 74078 (United States)

    2011-01-15

    Switchgrass (Panicum virgatum) has been identified as a model dedicated energy crop species. After a perennial grass is established, the major variable costs are for nitrogen (N) fertilizer and harvest. Prior to establishing switchgrass on millions of ha in a particular agro-climatic region, it would be useful to determine switchgrass yield response to N and its response to harvest frequency relative to alternative grass species. The objective of this research is to determine biomass yield response to N for four perennial grass species and to determine the species, N level, and harvest frequency that will maximize expected net returns, given the climate and soils of the U.S.A. Southern Plains. Yield data were produced in an experiment that includes four species (switchgrass, bermudagrass (Cynodon dactylon), weeping lovegrass (Eragrostis curvula), and carostan flaccidgrass (Pennisetum flaccidum)), four N levels, and two harvest levels. Linear response plateau (LRP), linear response stochastic plateau (LRSP), and quadratic response (QR) functions are estimated. For all combinations of biomass and N prices considered, the optimal species is switchgrass. For most price situations, it is economically optimal to fertilize established stands of switchgrass with 69 kg N ha{sup -1} yr{sup -1} and to harvest once yr{sup -1} after senescence. (author)

  9. Effects of harvesting time on some yield and quality traits of different ...

    African Journals Online (AJOL)

    The effect of harvesting time was investigated on yield and quality traits for spring season production in different maturing potato (Solanum tuberosum L.) cultivars under agro-climatic conditions of southern of Turkey in 2006 and 2007. The experimental layout was a randomized split plot with three replications, including six ...

  10. Energy harvesting in high voltage measuring techniques

    International Nuclear Information System (INIS)

    Żyłka, Pawel; Doliński, Marcin

    2016-01-01

    The paper discusses selected problems related to application of energy harvesting (that is, generating electricity from surplus energy present in the environment) to supply autonomous ultra-low-power measurement systems applicable in high voltage engineering. As a practical example of such implementation a laboratory model of a remote temperature sensor is presented, which is self-powered by heat generated in a current-carrying busbar in HV- switchgear. Presented system exploits a thermoelectric harvester based on a passively cooled Peltier module supplying micro-power low-voltage dc-dc converter driving energy-efficient temperature sensor, microcontroller and a fibre-optic transmitter. Performance of the model in laboratory simulated conditions are presented and discussed. (paper)

  11. Wild-harvested venison yields and sharing by Michigan deer hunters

    Science.gov (United States)

    Goguen, Amber D.; Riley, Shawn J.; Organ, John F.; Rudolph, Brent A.

    2018-01-01

    An increased societal focus on wildlife as food and recent policy deliberations regarding legal markets for wild-harvested meat are encouraging wildlife managers and researchers to examine the amount, use, and distribution of meat yielded through recreational hunting. We used responses to questions on the Michigan Deer Harvest Study to estimate the maximum yield of edible venison and assess hunters’ sharing behaviors. We estimated 11,402–14,473 metric tons of edible venison were procured during the 2013 hunting season. Of hunters who harvested a deer, 85% shared their venison. Hunters who shared did so with an average of 5.6 people (SD = 4.5). Sharing occurred most frequently within tight social networks: members of hunters’ households (69%), relatives (52%), and friends, neighbors, or coworkers (50%). In the absence of legal markets, venison is distributed widely by hunters and greatly amplifies the number of people benefiting from hunting. Nonetheless, we also identified the potential breadth of exposure to disease or contaminants from wild-harvested meat.

  12. Energy harvesting from high-rise buildings by a piezoelectric harvester device

    International Nuclear Information System (INIS)

    Xie, X.D.; Wang, Q.; Wang, S.J.

    2015-01-01

    A novel piezoelectric technology of harvesting energy from high-rise buildings is developed. While being used to harness vibration energy of a building, the technology is also helpful to dissipate vibration of the building by the designed piezoelectric harvester as a tuned mass damper. The piezoelectric harvester device is made of two groups of series piezoelectric generators connected by a shared shaft. The shaft is driven by a linking rod hinged on a proof mass on the tip of a cantilever fixed on the roof of the building. The influences of some practical considerations, such as the mass ratio of the proof mass to the main structure, the ratios of the length and flexural rigidity of the cantilever to those of the main structure, on the root mean square (RMS) of the generated electric power and the energy harvesting efficiency of the piezoelectric harvester device are discussed. The research provides a new method for an efficient and practical energy harvesting from high-rise buildings by piezoelectric harvesters. - Highlights: • A new piezoelectric technology in energy harvesting from high-rise buildings is introduced. • A new mathematics model to calculate the energy harvested by the piezoelectric device is developed. • A novel efficient design of the piezoelectric harvester device in provided. • An electric power up to 432 MW under a seismic excitation at a frequency of 30 rad/s is achieved.

  13. Time of harvest affects the yield of soluble polysaccharides extracted enzymatically from potato pulp

    DEFF Research Database (Denmark)

    Ravn, Helle Christine; Sørensen, Ole Bandsholm; Meyer, Anne S.

    2015-01-01

    properties as bifidogenic prebiotic fibers. The potato starch processing campaign is based on processing of fresh potatoes (in Denmark the campaign lasts from September to December). This study examines the effect of time of harvest and processing during the campaign on the yield of enzymatically solubilized...... fibers; this outcome may be the result of an inherent effect of the higher maturity of the potatoes late in the campaign....

  14. Willow yield is highly dependent on clone and site

    DEFF Research Database (Denmark)

    Ugilt Larsen, Søren; Jørgensen, Uffe; Lærke, Poul Erik

    2014-01-01

    Use of high-yielding genotypes is one of the means to achieve high yield and profitability in willow (Salix spp.) short rotation coppice. This study investigated the performance of eight willow clones (Inger, Klara, Linnea, Resolution, Stina, Terra Nova, Tora, Tordis) on five Danish sites......, differing considerably in soil type, climatic conditions and management. Compared to the best clone, the yield was up to 36 % lower for other clones across sites and up to 51 % lower within sites. Tordis was superior to other clones with dry matter yields between 5.2 and 10.2 Mg ha−1 year−1 during the first...... 3-year harvest rotation, and it consistently ranked as the highest yielding clone on four of the five sites and not significantly lower than the highest yielding clone on the fifth site. The ranking of the other clones was more dependent on site with significant interaction between clone and site...

  15. The data harvest how sharing research data can yield knowledge, jobs and growth : an RDA Europe report

    CERN Document Server

    Moran, Nuala

    2014-01-01

    In October 2010, the High Level Group on Scientific Data presented the "Riding the Wave,” report to the European Commission outlining a series of policy recommendations on how Europe could gain from the rising tide of scientific data. Over 4 years later, a team of European experts have generated a new report "The Data Harvest: How sharing research data can yield knowledge, jobs and growth" with an update on the landscape described in the previous report aiming to sound a warning on how Europe must act now to secure its standing in future data markets. In this report, we outline the benefits and challenges, and offer recommendations to European policy makers. The seeds have been sown. Now is the time to plan the harvest.

  16. Examining the roles that changing harvested areas, closing yield-gaps, and increasing yield ceilings have had on crop production

    Science.gov (United States)

    Johnston, M.; Ray, D. K.; Mueller, N. D.; Foley, J. A.

    2011-12-01

    With an increasing and increasingly affluent population, there has been tremendous effort to examine strategies for sustainably increasing agricultural production to meet this surging global demand. Before developing new solutions from scratch, though, we believe it is important to consult our recent agricultural history to see where and how agricultural production changes have already taken place. By utilizing the newly created temporal M3 cropland datasets, we can for the first time examine gridded agricultural yields and area, both spatially and temporally. This research explores the historical drivers of agricultural production changes, from 1965-2005. The results will be presented spatially at the global-level (5-min resolution), as well as at the individual country-level. The primary research components of this study are presented below, including the general methodology utilized in each phase and preliminary results for soybean where available. The complete assessment will cover maize, wheat, rice, soybean, and sugarcane, and will include country-specific analysis for over 200 countries, states, territories and protectorates. Phase 1: The first component of our research isolates changes in agricultural production due to variation in planting decisions (harvested area) from changes in production due to intensification efforts (yield). We examine area/yield changes at the pixel-level over 5-year time-steps to determine how much each component has contributed to overall changes in production. Our results include both spatial patterns of changes in production, as well as spatial maps illustrating to what degree the production change is attributed to area and/or yield. Together, these maps illustrate where, why, and by how much agricultural production has changed over time. Phase 2: In the second phase of our research we attempt to determine the impact that area and yield changes have had on agricultural production at the country-level. We calculate a production

  17. Effect of biweekly shoot tip harvests on the growth and yield of Georgia Jet sweet potato grown hydroponically

    Science.gov (United States)

    Ogbuehi, Cyriacus R.; Loretan, Phil A.; Bonsi, C. K.; Hill, Walter A.; Morris, Carlton E.; Biswas, P. K.; Mortley, Desmond G.

    1989-01-01

    Sweet potato shoot tips have been shown to be a nutritious green vegetable. A study was conducted to determine the effect of biweekly shoot tip harvests on the growth and yield of Georgia Jet sweet potato grown in the greenhouse using the nutrient film technique (NFT). The nutrient solution consisted of a modified half Hoagland solution. Biweekly shoot tip harvests, beginning 42 days after planting, provided substantial amounts of vegetable greens and did not affect the fresh and dry foliage weights or the storage root number and fresh and dry storage root weights at final harvest. The rates of anion and cation uptake were not affected by tip harvests.

  18. Yielding of leaf celery Apium graveolens L. var. secalinum Alef. depending on the number of harvests and irrigation

    Directory of Open Access Journals (Sweden)

    Ewa Rożek

    2013-04-01

    Full Text Available Leaf celery (Apium graveolensvar. secalinum is a vegetable with medicinal and spicy properties. Its numerous intensely fragrant leaves can be cut several times during the plant growing period. The aim of this study was to evaluate the effect of irrigation and number of harvests on leaf celery yield of the cultivars ‘Afina’ and‘Gewone Snij’. Plant irrigation significantly increased leaf yield and plant height of leaf celery. Higher total yield was obtained from non-irrigated plants when leaves were harvested three times, whereas for irrigated plants yield was higher in the case of two leaf harvests. Irrespective of the experimental factors, higher yield was obtained from the cultivar ‘Gewone Snij’.

  19. Effect of water stress on total biomass, tuber yield, harvest index and water use efficiency in Jerusalem artichoke

    Science.gov (United States)

    The objectives of this study were to determine the effect of drought on tuber yield, total biomass, harvest index, water use efficiency of tuber yield (WUEt) and water use efficiency of biomass (WUEb), and to evaluate the differential responses of Jerusalem artichoke (JA) varieties under drought str...

  20. Temperature, Sowing and Harvest Dates, and Yield of Maize in the Southwestern US

    Science.gov (United States)

    Kafatos, M.; Stack, D.; Myoung, B.; Kim, S. H.; Kim, J.

    2014-12-01

    Since sowing date of maize is sensitive to climate variability and changes, it is of a practical importance to examine how sowing dates affect maize yields in various temperature regimes in the southwestern US. A 21-year (1991-2011) simulation of maize yield using Agricultural Production Systems sIMulator (APSIM) with observed meteorological forcing, shows that earlier sowing dates are favorable for higher yields primarily by increasing the length of growing season in cold mountaineous regions. In these regions, warmer conditions in the sowing period tend to advance the sowing date and then enhance yield. Over low-elevation warm regions, yields are less correlated with sowing dates and the length of growing season, perhaps because growing season temperatures are high enough for fast growth. Instead, in the warm regions, maize yields are sensitive to temperature variations during the late growing season due to adverse effects of extreme high temperature events on maize development.

  1. High School Harvest: Combining Food Service Training and Institutional Procurement

    Science.gov (United States)

    Conner, David; Estrin, Hans; Becot, Florence

    2014-01-01

    This article discusses High School Harvest (HSH), an Extension educator-led project in five Vermont schools to provide students with job training and food system education and to provide lightly processed produce to school lunch programs. One hundred and twenty-one students participated, logging 8,752 hours growing, harvesting, and processing…

  2. Repeatability, number of harvests, and phenotypic stability of dry matter yield and quality traits of Panicum maximum jacq.

    Directory of Open Access Journals (Sweden)

    Francisco Duarte Fernandes

    2017-04-01

    Full Text Available Selection of superior forage genotypes is based on agronomic traits assayed in repeated measures. The questions are how repeatable the performance of individual genotypes is and how many harvests are needed to select the best genotypes. The objectives were to estimate repeatability coefficients of dry matter yield (DMY and forage quality, their phenotypic stability and the number of harvests needed for an accurate selection. Two randomized complete block design experiments data with 24 genotypes each, undergoing 12 and 16 harvests, over a period of 2 and 3 years, respectively, were used. The DMY repeatability estimates ranged from 0.42 to 0.55, suggesting a low heritability. The mean numbers of repeated measures were 5 and 7 harvests for 0.80 and 0.85 accuracy, respectively. The inclusion of the first two harvests negatively affects the estimates. Repeatability for quality traits ranged from 0.30 to 0.69, indicating low to moderate heritability.

  3. Effect of water stress and harvesting stages on quantitative and qualitative yields of coriander (Coriandrum sativum L.

    Directory of Open Access Journals (Sweden)

    A. Ahmadian

    2016-05-01

    Full Text Available In order to study the effect of drought stress and harvesting stages on quantitative and qualitative yields of Coriander (Coriandrum sativum L. this experiment was conducted on split plot based on a randomized completely block design with 3 replications in Torbat-e Heydariyeh University, Iran, during growing season of 2010-2011. Treatments were drought stress (in three levels no stress: control and irrigation in 60 and 30 percentage of FC as main plots and harvesting times (in 3 levels consist of: before flowering, flowering and after flowering as sub plots. Results showed that drought stress and harvesting stages had significant affected on leaf number, height, number of stem, wet and dry weight of plant, SPAD, proline content, carbohydrate content, essential oil yield and percentage and components of essential oil of coriander. Increasing water stress decreased yield and its components while enhanced proline and carbohydrate contents. Maximum of essential oil and its main components (linalool, alpha pentene, gamma terpinene, geranial acetate and camphor were in low stress that had significant difference with other stress treatments. Delaying in harvest enhanced yield and its components and essential oil percentage. Proline content had no significant difference between flowering and after flowering stages. Therefore, we can suggest low stress of water and harvest at after flowering stage to get maximum of yield.

  4. High relative humidity pre-harvest reduces post-harvest proliferation of Salmonella in tomatoes.

    Science.gov (United States)

    Devleesschauwer, Brecht; Marvasi, Massimiliano; Giurcanu, Mihai C; Hochmuth, George J; Speybroeck, Niko; Havelaar, Arie H; Teplitski, Max

    2017-09-01

    Outbreaks of human illness caused by enteric pathogens such as Salmonella are increasingly linked to the consumption of fruits and vegetables. Knowledge on the factors affecting Salmonella proliferation on fresh produce therefore becomes increasingly important to safeguard public health. Previous experiments showed a limited impact of pre-harvest production practices on Salmonella proliferation on tomatoes, but suggested a significant effect of harvest time. We explored the data from two previously published and one unpublished experiment using regression trees, which allowed overcoming the interpretational difficulties of classical statistical models with higher order interactions. We assessed the effect of harvest time by explicitly modeling the climatic conditions at harvest time and by performing confirmatory laboratory experiments. Across all datasets, regression trees confirmed the dominant effect of harvest time on Salmonella proliferation, with humidity-related factors emerging as the most important underlying climatic factors. High relative humidity the week prior to harvest was consistently associated with lower Salmonella proliferation. A controlled lab experiment confirmed that tomatoes containing their native epimicrobiota supported significantly lower Salmonella proliferation when incubated at higher humidity prior to inoculation. The complex interactions between environmental conditions and the native microbiota of the tomato crop remain to be fully understood. Copyright © 2017 Elsevier Ltd. All rights reserved.

  5. Effect of Harvesting Frequency, Variety and Leaf Maturity on Nutrient Composition, Hydrogen Cyanide Content and Cassava Foliage Yield

    Directory of Open Access Journals (Sweden)

    Khuc Thi Hue

    2012-12-01

    Full Text Available The experiment studied the effect of harvesting frequencies and varieties on yield, chemical composition and hydrogen cyanide content in cassava foliage. Foliage from three cassava varieties, K94 (very bitter, K98-7 (medium bitter and a local (sweet, were harvested in three different cutting cycles, at 3, 6 and 9 months; 6 and 9 months and 9 months after planting, in a 2-yr experiment carried out in Hanoi, Vietnam. Increasing the harvesting frequency increased dry matter (DM and crude protein (CP production in cassava foliage. The K94 variety produced higher foliage yields than the other two varieties. Dry matter, neutral detergent fibre (NDF, acid detergent fibre (ADF and total tannin content increased with months to the first harvest, whereas CP content decreased. Hydrogen cyanide (HCN content was lower at the first harvest than at later harvests for all cutting cycles. At subsequent harvests the content of total tannins tended to decline, while HCN content increased (p<0.05. Chemical composition differed somewhat across varieties except for total tannins and ash. Dry matter, NDF, ADF and total tannins were higher in fully matured leaves, while CP and HCN were lower in developing leaves.

  6. Effect of fertilization and harvest frequency on floristic composition and yields of meadow stand

    Directory of Open Access Journals (Sweden)

    Josef Raus

    2012-01-01

    Full Text Available The effect of fertilization and the harvest frequency on production and floristic characteristics of a meadow stand were assessed in a small plot trial established in 2003 in Vatín, Vysočina Region, the Czech Republic. Four levels of fertilization (none; N0 + P30 + K60 kg∙ha−1; N90 + P30 + K60 kg∙ha−1; N180 + P30 + K60 kg∙ha−1 were combined with four treatments of exploitation intensity (4 cuts per year, first cut on 15th May, every next after 45 days; 3 cuts per year, first cut on 30th May, every next after 60 days; 2 cuts per year, first cut on 15th June, next after 90 days; 2 cuts per year, first cut on 30th June, next after 90 days. Production of dry matter and proportions of guilds (grasses, legumes, and other species were evaluated. Data from 2009–2011 were used in this paper. Yields of the dry matter increased along with increasing amounts of nutrients supplied and ranged from 3.8 t∙ha−1 (non-fertilized to 9.1 t∙ha−1 (N180PK. The nutrition level had a significant effect on spread of grasses, which reached maximal proportion of 52.3 % under N180PK fertilization compared to 42.1% on non-fertilized plots. On the contrary, legumes flourished well in treatments without N-supply, attaining proportion of 6.8 % and 5.1 % on PK-fertilized and non-fertilized plot, respectively. With regard to the exploitation intensity grasses profited from extensive management by contrast to the group of other species which reached its maximum in swards harvested four times a year. Proportions of legumes did not show significant dependence on the cutting frequency.

  7. High-efficiency integrated piezoelectric energy harvesting systems

    Science.gov (United States)

    Hande, Abhiman; Shah, Pradeep

    2010-04-01

    This paper describes hierarchically architectured development of an energy harvesting (EH) system that consists of micro and/or macro-scale harvesters matched to multiple components of remote wireless sensor and communication nodes. The micro-scale harvesters consist of thin-film MEMS piezoelectric cantilever arrays and power generation modules in IC-like form to allow efficient EH from vibrations. The design uses new high conversion efficiency thin-film processes combined with novel cantilever structures tuned to multiple resonant frequencies as broadband arrays. The macro-scale harvesters are used to power the collector nodes that have higher power specifications. These bulk harvesters can be integrated with efficient adaptive power management circuits that match transducer impedance and maximize power harvested from multiple scavenging sources with very low intrinsic power consumption. Texas MicroPower, Inc. is developing process based on a composition that has the highest reported energy density as compared to other commercially available bulk PZT-based sensor/actuator ceramic materials and extending it to thin-film materials and miniature conversion transducer structures. The multiform factor harvesters can be deployed for several military and commercial applications such as underground unattended sensors, sensors in oil rigs, structural health monitoring, supply chain management, and battlefield applications such as sensors on soldier apparel, equipment, and wearable electronics.

  8. The influence of crop density and harvesting time on yield and quality of various sugar beet cultivars

    Directory of Open Access Journals (Sweden)

    Filipović Vladimir

    2009-01-01

    Full Text Available In this paper the influence of crop density and harvesting time on yield and quality of various sugar beet cultivars has been analyzed. During three year research conducted on soil of carbonate chernozem on loess terrace on experimental field of Institute Tamiš in Pančevo. Method of completely random block system in four repetitions we're analyzed the influence of crop density (80.000 plants per ha, 100.000 plants per ha and 120.000 plants per ha and harvesting time (10th Sept, 01st Oct and 20th Oct on yield and quality of various sugar beet cultivars of different technological type (Esprit N - type, Belinda Z - type and Chiara NE - type. Increase in crop density had very little effect on increase on sugar beet yield. The yield was considerably increased in the period between the first harvesting date and the second. The highest yield of consumable sugar was obtained of cultivars of N - type Esprit and lower yield was obtained of cultivars of Z - type (Belinda. .

  9. Evaluation of Sowing Date, Plant Density and Harvest Method on Growth, Yield and Yield Components of Baby Corn (Zea mays L. var. SC403su

    Directory of Open Access Journals (Sweden)

    A. Rahmani

    2014-12-01

    Full Text Available Considering importance of baby corn, the study was consisted of sowing date (14th June, 3th July and 24th July as main Plots and plant densities (6.5, 8.5 and 10.5. plant m-2 as sub Plots and two harvest methods (baby corn, as first harvest sweet corn and next ear as baby corn on Growth parameter and yield of baby corn (Zea mays L. Var SC403su in agricultural Research Center and Natural Resources of Khorasan Razavi Province, Mashhad on 2009. The experiment was carried out in a factorial split plot design based on randomized completely block design with 4 replications. The results showed the highest plant height on sowing date 3thJuly with average 168.6 cm. Also the highest standard ear percentage that one of the important factors for food manufactory had on sowing date 24th July with plant density 10.5 plants plant m-2, by harvesting method baby corn with 63.9 percentages. Also The results showed the highest substandard ear percentage of baby corn was belonged to sowing date 24th July with 8.5 plant m-2, by harvesting method (baby corn sweet corn with 74.6%. The highest harvest ear index was belonged to sowing date14thJune, by harvesting method (baby corn sweet corn with 35.29 percentages. Therefore, sowing date 3thJuly for forage production with average 4 kg m-2 by harvesting method baby corn are recommended for lateral produce production. Considering to Mashhad weather conditions, producing the highest and best standard ear percentage, density, 10.5 plants per square meter and 24th July planting is recommended.

  10. High yield fabrication of fluorescent nanodiamonds

    Energy Technology Data Exchange (ETDEWEB)

    Boudou, Jean-Paul; Curmi, Patrick A [Structure and Activity of Normal and Pathological Biomolecules-INSERM/UEVE U829, Universite d' Evry-Val d' Essonne, Batiment Maupertuis, Rue du pere Andre Jarlan, F-91025 Evry (France); Jelezko, Fedor; Wrachtrup, Joerg; Balasubramanian, Gopalakrischnan; Reuter, Rolf [3.Physikalisches Institut, University of Stuttgart, Pfaffenwaldring 57, D-70550 Stuttgart (Germany); Aubert, Pascal [Nanometric Media Laboratory, Universite d' Evry-Val d' Essonne, Batiment Maupertuis, Rue du pere Andre Jarlan, F-91025 Evry (France); Sennour, Mohamed; Thorel, Alain [Centre des Materiaux, Mines Paris, ParisTech, BP 87, F-91000 Evry (France); Gaffet, Eric [Nanomaterials Research Group-UMR 5060, CNRS, UTBM, Site de Sevenans, F-90010 Belfort (France)], E-mail: jpb.cnrs@free.fr, E-mail: pcurmi@univ-evry.fr, E-mail: f.jelezko@physik.uni-stuttgart.de

    2009-06-10

    A new fabrication method to produce homogeneously fluorescent nanodiamonds with high yields is described. The powder obtained by high energy ball milling of fluorescent high pressure, high temperature diamond microcrystals was converted in a pure concentrated aqueous colloidal dispersion of highly crystalline ultrasmall nanoparticles with a mean size less than or equal to 10 nm. The whole fabrication yield of colloidal quasi-spherical nanodiamonds was several orders of magnitude higher than those previously reported starting from microdiamonds. The results open up avenues for the industrial cost-effective production of fluorescent nanodiamonds with well-controlled properties.

  11. High yield fabrication of fluorescent nanodiamonds

    International Nuclear Information System (INIS)

    Boudou, Jean-Paul; Curmi, Patrick A; Jelezko, Fedor; Wrachtrup, Joerg; Balasubramanian, Gopalakrischnan; Reuter, Rolf; Aubert, Pascal; Sennour, Mohamed; Thorel, Alain; Gaffet, Eric

    2009-01-01

    A new fabrication method to produce homogeneously fluorescent nanodiamonds with high yields is described. The powder obtained by high energy ball milling of fluorescent high pressure, high temperature diamond microcrystals was converted in a pure concentrated aqueous colloidal dispersion of highly crystalline ultrasmall nanoparticles with a mean size less than or equal to 10 nm. The whole fabrication yield of colloidal quasi-spherical nanodiamonds was several orders of magnitude higher than those previously reported starting from microdiamonds. The results open up avenues for the industrial cost-effective production of fluorescent nanodiamonds with well-controlled properties.

  12. Switchgrass harvest time management can impact biomass yield and nutrient content

    Science.gov (United States)

    Switchgrass (Panicum virgatum L.) is a dedicated energy crop native to much of North America. While high-biomass yield is of significant importance for the development of switchgrass as a bioenergy crop, nutrient content in the biomass as it relates to biofuel conversion efficiency is also critical...

  13. GWAS for plant growth stages and yield components in spring wheat (Triticum aestivum L.) harvested in three regions of Kazakhstan.

    Science.gov (United States)

    Turuspekov, Yerlan; Baibulatova, Aida; Yermekbayev, Kanat; Tokhetova, Laura; Chudinov, Vladimir; Sereda, Grigoriy; Ganal, Martin; Griffiths, Simon; Abugalieva, Saule

    2017-11-14

    Spring wheat is the largest agricultural crop grown in Kazakhstan with an annual sowing area of 12 million hectares in 2016. Annually, the country harvests around 15 million tons of high quality grain. Despite environmental stress factors it is predicted that the use of new technologies may lead to increases in productivity from current levels of 1.5 to up to 3 tons per hectare. One way of improving wheat productivity is by the application of new genomic oriented approaches in plant breeding projects. Genome wide association studies (GWAS) are emerging as powerful tools for the understanding of the inheritance of complex traits via utilization of high throughput genotyping technologies and phenotypic assessments of plant collections. In this study, phenotyping and genotyping data on 194 spring wheat accessions from Kazakhstan, Russia, Europe, and CIMMYT were assessed for the identification of marker-trait associations (MTA) of agronomic traits by using GWAS. Field trials in Northern, Central and Southern regions of Kazakhstan using 194 spring wheat accessions revealed strong correlations of yield with booting date, plant height, biomass, number of spikes per plant, and number of kernels per spike. The accessions from Europe and CIMMYT showed high breeding potential for Southern and Central regions of the country in comparison with the performance of the local varieties. The GGE biplot method, using average yield per plant, suggested a clear separation of accessions into their three breeding origins in relationship to the three environments in which they were evaluated. The genetic variation in the three groups of accessions was further studied using 3245 polymorphic SNP (single nucleotide polymorphism) markers. The application of Principal Coordinate analysis clearly grouped the 194 accessions into three clades according to their breeding origins. GWAS on data from nine field trials allowed the identification of 114 MTAs for 12 different agronomic traits. Field

  14. Development of high yielding mutants in lentil

    International Nuclear Information System (INIS)

    Rajput, M.A.; Sarwar, G.; Siddiqui, K.A.

    2001-01-01

    Full text: Lentil (Lens culinaris Medik.) locally known as Masoor, is the second most important rabi pulse crop, after chickpea, in Pakistan. It is cultivated on an area of over 63,400 ha, which constitutes about 4.83% of the total area under pulses. The annual production of the crop is 28,200 tones with an average yield of 445 kg/ha. Yield at the national level is very low, about one-half of the world's yield, which is mainly due to non-availability of high yield potential genotypes. Keeping in view the importance of mutants in developing a large number of new varieties, an induced mutations programme was initiated at AEARC, Tandojam during 1987-88, to develop high yielding varieties in lentil. For this, seeds of two lentil varieties, 'Masoor-85' and 'ICARDA-8' had been irradiated with gamma-rays ranging from 100-600 Gy in NIAB, Faisalabad during 1990. Selections were made in M2 on the basis of earliness, plant height, branches/plant and 100 grain weight. After confirming these mutants in M3 they were promoted in station yield trials and studied continuously for three consecutive years (1993- 1995). Overall results revealed that these mutants have consistent improvement of earliness in flowering and maturity. Plant height also increased in all mutant lines except AEL 23/40/91 where reduction in this attribute was observed as compared to parent variety. Mutant lines AEL 49/20/91 and AEL 13/30/91 showed improvement in 100 grain weight. The improvement of some agronomic characters enhanced the yield of mutant lines in comparison to parent varieties (Masoor-85 and ICARDA-8). The diversity in yield over the respective parents was computed from 6.94 to 60.12%. From these encouraging results it is hoped that mutant lines like AEL 12/30/91 and AEL 49/20/91 may serve as potential lentil genotypes in future. (author)

  15. PREOVULATORY FOLLICLE DEVELOPMENT IN HIGH YIELDING COWS

    Directory of Open Access Journals (Sweden)

    Radovan Tomášek

    2013-06-01

    Full Text Available The aim of the study was to examine the development of preovulatory follicles in pregnant and non-pregnant high yielding cows. The treatment by supergestran and oestrophan was used to synchronize the estrous cycle. Ovaries were monitored by transrectal ultrasonography. The linear increase of preovulatory follicles was observed in pregnant (P < 0,001 and non-pregnant (P < 0,001 cows during 8 days before ovulation. In conclusion, preovulatory follicles in pregnant and non-pregnant high yielding cows developed similarly.

  16. Approaches to achieve high grain yield and high resource use efficiency in rice

    Directory of Open Access Journals (Sweden)

    Jianchang YANG

    2015-06-01

    Full Text Available This article discusses approaches to simultaneously increase grain yield and resource use efficiency in rice. Breeding nitrogen efficient cultivars without sacrificing rice yield potential, improving grain fill in later-flowering inferior spikelets and enhancing harvest index are three important approaches to achieving the dual goal of high grain yield and high resource use efficiency. Deeper root distribution and higher leaf photosynthetic N use efficiency at lower N rates could be used as selection criteria to develop N-efficient cultivars. Enhancing sink activity through increasing sugar-spikelet ratio at the heading time and enhancing the conversion efficiency from sucrose to starch though increasing the ratio of abscisic acid to ethylene in grains during grain fill could effectively improve grain fill in inferior spikelets. Several practices, such as post-anthesis controlled soil drying, an alternate wetting and moderate soil drying regime during the whole growing season, and non-flooded straw mulching cultivation, could substantially increase grain yield and water use efficiency, mainly via enhanced remobilization of stored carbon from vegetative tissues to grains and improved harvest index. Further research is needed to understand synergistic interaction between water and N on crop and soil and the mechanism underlying high resource use efficiency in high-yielding rice.

  17. Pre-Harvest Application of a New Biocontrol Formulation Induces Resistance to Post-Harvest Anthracnose and Enhances Fruit Yield in Mango

    Directory of Open Access Journals (Sweden)

    R. Vivekananthan

    2006-08-01

    Full Text Available Pre-harvest application of biocontrol formulations consisting of 1. the two plant growth promoting rhizobacterial strains FP7 and Pf1 of Pseudomonas fluorescens; 2. a strain of Bacillus subtilis Bs-1; and 3. a strain (Sc-1 of the yeast Saccharomyces cerevisiae, given at fortnightly or monthly intervals and with or without a chitin amendment, were evaluated in two trials for their ability to reduce anthracnose in mango caused by Colletotrichum gloeosporioides. Growth of C. gloeosporioides in vitro was significantly reduced by strain FP7 and in both field trials the bacterial strain in combination with chitin significantly reduced infection. Pre-harvest application of these formulations at fortnightly intervals also significantly improved flower initiation, yield parameters (mean number of fruits and fruit yield and fruit quality (total soluble solids, ascorbic acid, free acidity, total, reducing and non- reducing sugar content. The delay in latent symptom expression increased by 15 days under stored conditions. The highest levels of phenolic content, peroxidase and polyphenol oxidase on mango leaves, flowers and fruits were achieved with FP7 +chitin.

  18. High-yield pulping effluent treatment technologies

    International Nuclear Information System (INIS)

    Su, W.X.; Hsieh, J.S.

    1993-03-01

    The objective of this report is to examine the high-yield (mechanical) pulp processes with respect to environmental issues affected by the discharge of their waste streams. Various statistics are given that support the view that high-yield pulping processes will have major growth in the US regions where pulp mills are located, and sites for projects in the development phase are indicated. Conventional and innovative effluent-treatment technologies applicable to these processes are reviewed. The different types of mechanical pulping or high-yield processes are explained, and the chemical additives are discussed. The important relationship between pulp yield and measure of BOD in the effluent is graphically presented. Effluent contaminants are identified, along with other important characteristics of the streams. Current and proposed environmental limitations specifically related to mechanical pulp production are reviewed. Conventional and innovative effluent-treatment technologies are discussed, along with their principle applications, uses, advantages, and disadvantages. Sludge management and disposal techniques become an intimate part of the treatment of waste streams. The conclusion is made that conventional technologies can successfully treat effluent streams under current waste-water discharge limitations, but these systems may not be adequate when stricter standards are imposed. At present, the most important issue in the treatment of pulp-mill waste is the management and disposal of the resultant sludge

  19. Repeated applications of CPPU on highbush blueberry cv. Duke increase yield and enhance fruit quality at harvest and during postharvest

    Directory of Open Access Journals (Sweden)

    Jorge B Retamales

    2014-04-01

    Full Text Available Applications of N-(2-chloro-4-pyridyl-N'-phenylurea (CPPU can increase blueberry (Vaccinium corymbosum L. yield and fruit size, but their impact on postharvest is unknown. We studied repeated CPPU applications effects on yield and quality (harvest, postharvest, over 2 yr on mature 'Duke' plants in South-Central Chile. The first year, 5 or 10 mL L-1 CPPU was applied at 3, 10, and/or 17 d after full bloom (DAFB plus a non-sprayed control. The second year, 5 or 10 mL L-1 CPPU were sprayed 10 and 17 DAFB plus a control. The first year, only 10 mL L-1 CPPU sprayed 3+17 DAFB increased yield (32.5% > control; 10 mL L-1 CPPU applied 10 or 3+17 DAFB had highest fruit diameter; and 10 mL L-1 CPPU at 17 DAFB or at 3+10+17 DAFB had highest soluble solids. Overall, 10 mL L-1 CPPU applied 3+17 DAFB, was the best treatment for year one, since it increased fruit yield and diameter, while soluble solids and postharvest weight loss were similar to control. The second year, 10 mL L-1 CPPU reduced fruit coloration (blue color coverage index: BCCI and soluble solids, but not firmness at harvest. This rate increased berry weight (24.2% and fruit wax (59% > wax coverage index: WCI at harvest. Harvest and postharvest WCI increased consistently as CPPU rate increased. CPPU reduced fruit rotting (15% at 45+5 evaluation. During storage, CPPU-treated-fruit had a slower decrease in firmness (30.5% < control at 30+1, but no difference at 30+5. CPPU-treated-fruit usually had higher post harvest soluble solids. Ten mL L-1 CPPU retarded color evolution at harvest and at 30+1, but not at 30+5, 40+1 or 40+5.

  20. High yielding rice mutants for West Bengal

    International Nuclear Information System (INIS)

    Debnath, A.R.; Sen, S.

    1980-01-01

    Four high yielding mutants with specific genetic corrections of the simply inherited characters were developed from IR-8 through X-irradiation. Recurrent selections of the promising isolates were made under diverse agro-climatic conditions in Winter and Summer seasons of West Bengal. The isolates CNM 6 and CNM 25 belonging to early maturity group and CNM 20 and CNM 31, to mid-early maturity group were finally selected at X 5 generation on the basis of their resistance qualities, maturity period and grain yield. They were evaluated upto X 10 qeneration at multi-locations as Pre-release and Minikit Varieties at State level. They were also placed at the National Screening Nursery (NSN) for screening against multiple diseases and pests at the National level. CNM 6 is reported to be promising in IRTP nurseries. It is reported that CNM 25 (IET 5646) ranked 2nd on the basis of average grain yield, CNM 20 (IET 5937) and CNM 31 (IET 5936) were resistant to diseases and with yield comparable to Jaya. These four productive mutants of superior types are widely accepted. CNM 6 is recommended for cultivation in Bankura and Birbhum districts and CNM 25 and CNM 31 in the different agro-climatic zones of West Bengal. (author)

  1. High green fodder yielding new grass varieties

    OpenAIRE

    C. Babu, K. Iyanar and A. Kalamani

    2014-01-01

    Two high biomass yielding forage grass varieties one each in Cumbu Napier hybrid and Guinea grass have been evolved at the Department of Forage Crops, Centre for Plant Breeding and Genetics, Tamil Nadu Agricultural University, Coimbatore and identified for release at national (All India) level as Cumbu Napier hybrid grass CO (BN) 5 and Guinea grass CO (GG) 3 during 2012 and 2013 respectively. Cumbu Napier hybrid grass CO (BN) 5 secured first rank at all national level with reference to green ...

  2. Methods for high yield production of terpenes

    Energy Technology Data Exchange (ETDEWEB)

    Kutchan, Toni; Higashi, Yasuhiro; Feng, Xiaohong

    2017-01-03

    Provided are enhanced high yield production systems for producing terpenes in plants via the expression of fusion proteins comprising various combinations of geranyl diphosphate synthase large and small subunits and limonene synthases. Also provided are engineered oilseed plants that accumulate monoterpene and sesquiterpene hydrocarbons in their seeds, as well as methods for producing such plants, providing a system for rapidly engineering oilseed crop production platforms for terpene-based biofuels.

  3. [Characteristics of phosphorus uptake and use efficiency of rice with high yield and high phosphorus use efficiency].

    Science.gov (United States)

    Li, Li; Zhang, Xi-Zhou; Li, Tinx-Xuan; Yu, Hai-Ying; Ji, Lin; Chen, Guang-Deng

    2014-07-01

    A total of twenty seven middle maturing rice varieties as parent materials were divided into four types based on P use efficiency for grain yield in 2011 by field experiment with normal phosphorus (P) application. The rice variety with high yield and high P efficiency was identified by pot experiment with normal and low P applications, and the contribution rates of various P efficiencies to yield were investigated in 2012. There were significant genotype differences in yield and P efficiency of the test materials. GRLu17/AiTTP//Lu17_2 (QR20) was identified as a variety with high yield and high P efficiency, and its yields at the low and normal rates of P application were 1.96 and 1.92 times of that of Yuxiang B, respectively. The contribution rate of P accumulation to yield was greater than that of P grain production efficiency and P harvest index across field and pot experiments. The contribution rates of P accumulation and P grain production efficiency to yield were not significantly different under the normal P condition, whereas obvious differences were observed under the low P condition (66.5% and 26.6%). The minimal contribution to yield was P harvest index (11.8%). Under the normal P condition, the contribution rates of P accumulation to yield and P harvest index were the highest at the jointing-heading stage, which were 93.4% and 85.7%, respectively. In addition, the contribution rate of P accumulation to grain production efficiency was 41.8%. Under the low P condition, the maximal contribution rates of P accumulation to yield and grain production efficiency were observed at the tillering-jointing stage, which were 56.9% and 20.1% respectively. Furthermore, the contribution rate of P accumulation to P harvest index was 16.0%. The yield, P accumulation, and P harvest index of QR20 significantly increased under the normal P condition by 20.6%, 18.1% and 18.2% respectively compared with that in the low P condition. The rank of the contribution rates of P

  4. Effects of temperature sum on vitamin C concentration and yield of sea buckthorn (Hippophae rhamnoides fruit: optimal time of fruit harvest

    Directory of Open Access Journals (Sweden)

    Yingmou Yao

    1993-12-01

    Full Text Available To investigate the effects of temperature sum on vitamin C concentration (Vc, yield and maturity of sea buckthorn fruit (Hippophae rhamnoides L. and to predict the optimal harvest time, berries were collected from eight genotypes at an interval of about one week from August 16 to December 2. Maturity was visually observed, berry weight measured and Vc determined. Berries matured at 1165-1316 degree-days (d.d.. Vc reached maximum at about 1229 d.d., while fruit size and yield reached maximum at 1380 d.d.. Mathematical models of polynomial equations were highly significant for predicting the effects of temperature sum on Vc, maturity and fruit yield. Optimal harvest time for maximizing Vc, yield or economic income could be determined according to differential equations. Great variations in Vc, fruit maturity and fruit size suggested good opportunities for selection and breeding. Low rank correlations in vitamin C concentration during fruit maturity, however, call for special attention in selection and breeding.

  5. Effects of harvesting stages on yield and nutritional quality of African ...

    African Journals Online (AJOL)

    SARAH

    2014-06-30

    Jun 30, 2014 ... The influence of these harvesting practices on fruit productivity and nutritional ... development while still on the plants (Hornal et al., ... East. The University lies at an altitude of 525 m above sea level and has ... The area has fertile red sand-clay soil with ..... development in deciduous tree crops as affected.

  6. Influence of harvest time and frequency on light interception and biomass yield of festulolium and tall fescue cultivated on a peatland

    DEFF Research Database (Denmark)

    Kandel, Tanka; Elsgaard, Lars; Andersen, Mathias Neumann

    2016-01-01

    managements,which contributed to similar IPAR (908–919 MJ m−2), total biomass yield (16.4–18.8 Mg DM ha−1yr−1)and RUE (1.80–2.07 g MJ−1) for all managements. Whereas both crops were highly productive under both3C management and 2C management with first harvest after flowering (i.e., 2C-late), the 2C......tIn this study, we report efficiencies of light capture and biomass yield of festulolium and tall fescue cul-tivated on a riparian fen in Denmark under different harvesting managements. Green biomass targetedfor biogas production was harvested either as two cuts (2C) or three cuts (3C) in a year....... Three differenttimings of the first cut in the 2C systems were included as early (2C-early), middle (2C-mid) and late (2C-late) cuts corresponding to pre-heading, inflorescence emergence and flowering stages, respectively. Thefraction of intercepted photosynthetically active radiation (fPAR) was derived...

  7. Long-term Miscanthus Yields Influenced by Location, Genotype, Row Distance, Fertilization and Harvest Season

    DEFF Research Database (Denmark)

    Ugilt Larsen, Søren; Jørgensen, Uffe; Kjeldsen, Jens Bonderup

    2014-01-01

    Long-term yield studies in perennial crops like miscanthus are important to determine mean annual energy yield and the farmer’s economy. In two Danish field trials, annual yield of two miscanthus genotypes was followed over a 20-year period. The trials were established in 1993 on loamy sand...

  8. Cotton harvest at 40% versus 75% boll-splitting on yield and economic return under standard and proactive boll weevil (Coleoptera: Curculionidae) spray regimes.

    Science.gov (United States)

    Showler, A T; Robinson, J R C

    2008-10-01

    The standard practice of two or three preemptive insecticide applications at the start of pinhead (1-2-mm-diameter) squaring followed by threshold-triggered (when 10% of randomly selected squares have oviposition punctures) insecticide applications for boll weevil, Anthonomus grandis grandis Boheman (Coleoptera: Curculionidae), control does not provide reliable protection of cotton, Gossypium hirsutum L., lint production. This study, conducted during 2004 and 2005, showed that three to six fewer spray applications in a "proactive" approach, in which spraying began at the start of large (5.5-8-mm-diameter) square formation and continued at approximately 7-d intervals while large squares were abundant, resulted in fewer infested squares and 1.4- to 1.7-fold more lint than the standard treatment. Fewer sprays and increased yield made proactive spraying significantly more profitable than the standard approach, which resulted in relatively low or negative economic returns. Harvest at 75% boll-split in the proactive spray regime of 2005 resulted in four-fold greater economic return than cotton harvested at 40% boll-split because of improved protection of large squares and the elimination of late-season sprays inherent to standard spray regime despite the cost of an extra irrigation in the 75% boll-split treatments. The earlier, 40% harvest trigger does not avoid high late-season boll weevil pressure, which exerts less impact on bolls, the predominant form of fruiting body at that time, than on squares. Proactive spraying and harvest timing are based on an important relationship between nutrition, boll weevil reproduction, and economic inputs; therefore, the tactic of combining proaction with harvest at 75% boll-split is applicable where boll weevils are problematic regardless of climate or region, or whether an eradication program is ongoing.

  9. A metamaterial electromagnetic energy rectifying surface with high harvesting efficiency

    Directory of Open Access Journals (Sweden)

    Xin Duan

    2016-12-01

    Full Text Available A novel metamaterial rectifying surface (MRS for electromagnetic energy capture and rectification with high harvesting efficiency is presented. It is fabricated on a three-layer printed circuit board, which comprises an array of periodic metamaterial particles in the shape of mirrored split rings, a metal ground, and integrated rectifiers employing Schottky diodes. Perfect impedance matching is engineered at two interfaces, i.e. one between free space and the surface, and the other between the metamaterial particles and the rectifiers, which are connected through optimally positioned vias. Therefore, the incident electromagnetic power is captured with almost no reflection by the metamaterial particles, then channeled maximally to the rectifiers, and finally converted to direct current efficiently. Moreover, the rectifiers are behind the metal ground, avoiding the disturbance of high power incident electromagnetic waves. Such a MRS working at 2.45 GHz is designed, manufactured and measured, achieving a harvesting efficiency up to 66.9% under an incident power density of 5 mW/cm2, compared with a simulated efficiency of 72.9%. This high harvesting efficiency makes the proposed MRS an effective receiving device in practical microwave power transmission applications.

  10. A metamaterial electromagnetic energy rectifying surface with high harvesting efficiency

    Science.gov (United States)

    Duan, Xin; Chen, Xing; Zhou, Lin

    2016-12-01

    A novel metamaterial rectifying surface (MRS) for electromagnetic energy capture and rectification with high harvesting efficiency is presented. It is fabricated on a three-layer printed circuit board, which comprises an array of periodic metamaterial particles in the shape of mirrored split rings, a metal ground, and integrated rectifiers employing Schottky diodes. Perfect impedance matching is engineered at two interfaces, i.e. one between free space and the surface, and the other between the metamaterial particles and the rectifiers, which are connected through optimally positioned vias. Therefore, the incident electromagnetic power is captured with almost no reflection by the metamaterial particles, then channeled maximally to the rectifiers, and finally converted to direct current efficiently. Moreover, the rectifiers are behind the metal ground, avoiding the disturbance of high power incident electromagnetic waves. Such a MRS working at 2.45 GHz is designed, manufactured and measured, achieving a harvesting efficiency up to 66.9% under an incident power density of 5 mW/cm2, compared with a simulated efficiency of 72.9%. This high harvesting efficiency makes the proposed MRS an effective receiving device in practical microwave power transmission applications.

  11. High temperature energy harvesters utilizing ALN/3C-SiC composite diaphragms

    Science.gov (United States)

    Lai, Yun-Ju; Li, Wei-Chang; Felmetsger, Valery V.; Senesky, Debbie G.; Pisano, Albert P.

    2014-06-01

    Microelectromechanical systems (MEMS) energy harvesting devices aiming at powering wireless sensor systems for structural health monitoring in harsh environments are presented. For harsh environment wireless sensor systems, sensor modules are required to operate at elevated temperatures (> 250°C) with capabilities to resist harsh chemical conditions, thereby the use of battery-based power sources becomes challenging and not economically efficient if considering the required maintenance efforts. To address this issue, energy harvesting technology is proposed to replace batteries and provide a sustainable power source for the sensor systems towards autonomous harsh environment wireless sensor networks. In particular, this work demonstrates a micromachined aluminum nitride/cubic silicon carbide (AlN/3C-SiC) composite diaphragm energy harvester, which enables high temperature energy harvesting from ambient pulsed pressure sources. The fabricated device yields an output power density of 87 μW/cm2 under 1.48-psi pressure pulses at 1 kHz while connected to a 14.6-kΩ load resistor. The effects of pulse profile on output voltage have been studied, showing that the output voltage can be maximized by optimizing the diaphragm resonance frequency based on specific pulse characteristics. In addition, temperature dependence of the diaphragm resonance frequency over the range of 20°C to 600°C has been investigated and the device operation at temperatures as high as 600°C has been verified.

  12. Microbial Species and Functional Diversity in Rice Rhizosphere of High-yield Special Ecological Areas

    Directory of Open Access Journals (Sweden)

    PAN Li-yuan

    2016-11-01

    Full Text Available Taoyuan, Yunnan Province is a special eco-site which keeps the highest yield records of rice cultivation in small planting areas. Soil microbial species and functional diversity were evaluated using cultivation method and BIOLOG ecoplates. The results showed that the microbial community of the high yield region was more abundant, and the total microbial population was 2 times of the control, furthermore, the areas belonged to the healthy "bacteria" soil, which was showed as bacteria > actinomycetes > fungi. Bacteria were the dominant populations in the rhizosphere of high yielding rice field, and the yield formation of rice was not correlated with the depth of soil layers. In order to obtain more species diversity information, Shannon diversity index H, Shannon evenness index E and Simpson index D were analyzed, and the results showed that microbial community diversity and evenness were not the main differences between the high and general yield areas. Then, the functional diversity of soil microbial community was investigated through the average well color development(AWCD and diversity index analyses. The results of AWCD analysis indicated that the metabolic activity of soil microbial community in high yield paddy soils were stronger than the control. Moreover, the difference range from large to small showed as tillering stage > harvest period > seedling period > rotation period, the stronger the rice growth, the greater the difference between the high yield region and the control. At tillering stage and harvest stage, due to the vigorous plant growth, the root exudates were rich, and the microbial communities of high yield paddy soils showed a strong metabolic activity and strong ability to use carbon sources. The results of Shannon, Simpson and McIntosh indices analysis indicated that common microbial species was not a key factor affecting the yield of rice. Tillering stage was a key period for the growth of high yield rice, and many

  13. Effect of a short and severe intermittent drought on transpiration, seed yield components, and harvest index in four landraces of bambara groundnut

    DEFF Research Database (Denmark)

    Jørgensen, Søren Thorndal; Ntundu, W.H.; Ouédraogo, M.

    2011-01-01

    % of pot holding capacity until seed maturity or drought-stressed (DS) in the period from 76 to 85 days after sowing (flowering and early podding stage). During drought, although the total water use differed among the four landraces, transpiration rate and stomatal conductance (gs) responded similarly...... to soil drying. The high soil water thresholds for the reduction of transpiration rate and gs of bambara groundnuts indicate their great sensitivity in the stomatal control over plant water loss during soil drying. Even though the shoot dry weight at maturity was hardly affected by DS, seed yield, seed...... number, and harvest index were all significantly decreased in the DS plants. Among landraces, LunT and Ramayana were more susceptible to DS than S19-3 and Uniswa Red in terms of reduction of seed number and seed yield. The different responses of the landraces to DS may reflect their adaptation...

  14. Spatial and harvesting influence on growth, yield, quality and economic potential of Kalmegh (Andrographis paniculata Wall Ex. Nees

    Directory of Open Access Journals (Sweden)

    Sanjeev Kumar

    2013-08-01

    Full Text Available Andrographis paniculata, commonly known as Kalmegh, is used both in Ayurvedic and Unani system of medicines because of its immunological, antibacterial and hepatoprotective properties. This study was carried out to investigate the influence of four harvesting times (120,135,150 days after planting and at seed maturity and four planting distances (30×15, 30×10, 20×15 and 20×10 cm on growth, dry herbage biomass, seed yield and quality traits of Andrographis paniculata at CCS Haryana Agricultural University, Hisar, India in the two years 2005 and 2006. The treatments were laid out in a split plot design with three replications. The maximum values for dry herbage biomass yield (5.14 t ha^(-1, net returns (760.00 EUR ha^(-1, B:C ratio (2.59, andrographolide content (2.63% and total yield (135.00 kg ha^(-1 were detected 135 days after planting with an optimum planting distance of 30×15 cm. However, the maximum iron content was estimated 120 days after planting. The highest dry herbage (4.58 t ha^(-1 and maximum seed yield (19.7 kg ha^(-1 were registered at plants that were lined out with a distance of 20×10 cm.

  15. Effect of Harvest Methods on Yield and Quaiityof·Marketable ...

    African Journals Online (AJOL)

    cultivars of (ii1ferent growth habits: '0~'cf/~~' 'q;a~i/Giulq' rffP ... Key words: Greerihollse' rose, h~est methods, growth-habits, 'yield and guality of flowers. ,-. ',' ! ' ! ' . • . . ) Introduction .... dure" and "Duncan's Multiple Range test'''·re- spedivel~' of a ...

  16. Harvesting Robots for High-value Crops: State-of-the-art Review and Challenges Ahead

    NARCIS (Netherlands)

    Bac, C.W.; Henten, van E.; Hemming, J.; Edan, Y.

    2014-01-01

    This review article analyzes state-of-the-art and future perspectives for harvesting robots in high-value crops. The objectives were to characterize the crop environment relevant for robotic harvesting, to perform a literature review on the state-of-the-art of harvesting robots using quantitative

  17. Plant growth analysis used as secondary traits in selection for high yield on groundnut

    International Nuclear Information System (INIS)

    Manshuri, A.G.; Nugrahaeni

    1996-01-01

    Groundnut growth and yield can be expressed as the product to solar radiation interception (Qi), conversion efficiency of radiation to total dry matter (Ek) and partitioning efficiency to economic yield (Ep) or harvest index. Groundnut genotypes differ in characters related to Qi, Ek and Ep, and the characters have the possibility to be used as secondary traits in selection for high yield. Extinction coefficient (k) and leaf area index (LAI) are the influential factors in increasing Qi. Variability in leaf size lead to the description of the existence of variability in k value within the genotypes under study. LAI three is the level necessary to attain 90 percent total radiation absorption in groundnut. An increased of LAI exceeding four would be inefficient for increasing the fraction of radiation absorption. Convertion efficiency of radiation to total dry matter (Ek) related to the rate of plant photosynthesis and respiration, inspite of the need study the field, however, the study was still limited. Harvest index can be used as a secondary trait to identify high yield genotypes. There was a positive correlation between pod yield and harvest index. An increased of harvest index by 1 percent caused an increased of dry pod as high as 0.365 g/plant. ICG 1697, ICGV 86844 and ICGV 87161 gave yield more than 3.5 t/ha, and their total dry matter (TDM) were 49.2, 52.5 and 40.7 g/plant, whereas their harvest indexes (HI) were 0.47, 0.46 and 0.55, respectively. Theoretically, improvement of the groundnut pod yield can be attained by using variety which has TDM 52.5 g/plant and HI 0.55. Using HI as secondary selection criteria, five genotypes were selected, i.e., G/C/LM-88-B-25 (HI 0.59), local Irian and local Lombok (HI 0.57), ICGV 87161 and LM/ICGV 87165-B-2-1 (HI 0.55). Two genotypes were selected for their high TDM, namely ICGV 86844 and LM/ICGV 87165-88-B-82 [in

  18. Effects of levels of potassium and nitrogen on yields and post-harvest conservation of onions in winter

    Directory of Open Access Journals (Sweden)

    Geraldo Milanez de Resende

    2014-08-01

    Full Text Available Potassium and nitrogen are the elements present in the highest percentage in the onion dry matter. The objective of this experiment was to evaluate yield and post-harvest conservation of Vale Ouro IPA-11 onion cultivar regarding to nitrogen and potassium levels. The experiment was carried out in Petrolina-PE, Brazil, from June to September 2009. The experimental design was a completely randomized block in a 4 x 3 factorial design, composed of four nitrogen levels (0, 60, 120 and 180 kg ha-1 and three potassium levels (0, 90 and 180 kg ha-1 with three replications. The highest yield of commercial bulbs was achieved at an estimated N level of 172.6 kg ha-1. The lowest yield of noncommercial bulbs was estimated at N level of 147.0 kg ha-1. Lower percentage of smaller bulbs (class 2 were obtained by increasing levels of N x K, with a quadratic effect at the dose of 90 kg ha-1 K2O and minimum production point with 127.6 kg N ha-1 (20.3%. Regarding larger caliber bulbs (class 4, linear effects were found both in the absence and for the level of 90 kg ha-1 of K2O as levels of N were increased. When the highest level of 180 kg ha-1 K2O was applied, the level of 92.8 kg ha-1 of N was estimated as the one that would promote the highest bulb yield of this class (35.4%, and 5.3% was found in the lack of potassium fertilization.

  19. Efeito do tempo de experiência de operadores de Harvester no rendimento operacional Effect of time experience of Harvester operators in operating yield

    Directory of Open Access Journals (Sweden)

    Elaine Cristina Leonello

    2012-12-01

    Full Text Available A mecanização da colheita de madeira permite maior controle dos custos e pode proporcionar reduções em prazos relativamente curtos. Além disso, tem um lugar de destaque na humanização do trabalho florestal e no aumento do rendimento operacional. O presente trabalho teve por objetivo avaliar o desempenho de operadores de harvester em função do tempo de experiência na atividade. Foram avaliados oito operadores do sexo masculino, com idade entre 23 e 46 anos. O estudo consistiu na análise do volume de madeira colhida pelo harvester. O tempo de experiência afeta significativamente o rendimento operacional dos operadores de harvester. Tal rendimento aumenta expressivamente nos primeiros 18 meses de experiência, mantendo-se em ascensão nos próximos 26 meses. Após os 44 meses de experiência, o rendimento dos operadores tende a reduzir, revelando as possíveis acomodações do cotidiano. Tais resultados permitem concluir que por volta dos 50 meses de experiência na atividade de operação de harvester, se faz necessária a adoção de medidas de reciclagem, motivação, entre outras, a fim de proporcionar aos operadores melhores condições de trabalho que os possibilitem continuar exercendo a atividade de forma eficiente e rentável à empresa.The mechanization of timber harvesting allows greater control of costs and can provide reductions in relatively short intervals. Moreover, it has a place in the humanization of the working forest and the increase in performance. This work provides comparisons of operating performance of different operator harvester according to the time of experience in the activity. The operators evaluated were eight males, aged between 23 and 46 years old. The study consisted of analysis of the volume of timber harvested by the harvester. The experience significantly affects the performance of harvesters operators. The performance increases significantly in the first 18 months of experience, and it remained on

  20. High Power Density, Lightweight Thermoelectric Metamaterials for Energy Harvesting

    Data.gov (United States)

    National Aeronautics and Space Administration — Thermoelectric energy harvesting utilizes materials that generate an electrical current when subjected to a temperature gradient, or simply, a hot and cold source of...

  1. Green ear yield and grain yield of maize after harvest of the first ear as baby corn Rendimentos de espigas verdes e de grãos de milho após a colheita da primeira espiga como minimilho

    Directory of Open Access Journals (Sweden)

    Paulo Sérgio L e Silva

    2006-06-01

    Full Text Available Baby corn (BC consists of the corn ear harvested two or three days after silk emergence. BC is a profitable crop, making possible a diversification of production, aggregation of value and increased income. Removing the first female inflorescence induces corn to produce others, making possible to produce several BC ears or, alternatively, BC (by harvesting the first ear and green ears or grain. The objective of this work was to evaluate green ear yield and grain yield, after harvesting the first ear as BC. Corn cultivar AG 1051 was submitted to the following treatments, in a random block design with ten replicates (52 plants per plot: BC harvesting; green ear harvesting (grain moisture content between 60 and 70%; mature ear harvesting; BC harvesting and harvesting of other ears as green or mature ears. Marketable green ears yield or grain yield produced without removing the first inflorescence were superior to the green ears yield or grain yield produced after removal of the first inflorescence harvested as baby corn. Harvesting only the first ear as baby corn, and then harvesting green ears or the mature ears, provided lower baby corn yields than that obtained by harvesting all ears as baby corn. Economically, the best net revenues would be obtained by exploring the crop for the production of green ears, green ears + baby corn, baby corn, baby corn + grain, and grain, in this order.O minimilho (MM é a espiga do milho colhida dois a três dias após a emergência dos estilo-estigmas. O MM é rentável e propicia diversificação da produção, agregação de valor e ampliação de renda. A remoção da primeira inflorescência feminina induz o milho a produzir outras. Isso possibilita a produção de várias espigas de MM ou, alternativamente, MM (colhendo-se a primeira espiga e espigas verdes ou grãos. O objetivo do trabalho foi avaliar os rendimentos de espigas verdes e de grãos, após a colheita da primeira espiga como MM. A cultivar AG

  2. High Frequency Supercapacitors for Piezo-based Energy Harvesting

    Science.gov (United States)

    Ervin, Matthew; Pereira, Carlos; Miller, John; Outlaw, Ronald; Rastegar, Jay; Murray, Richard

    2013-03-01

    Energy harvesting is being investigated as an alternative to batteries for powering munition guidance and fuzing functions during flight. A piezoelectric system that generates energy from the oscillation of a mass on a spring (set in motion by the launch acceleration) is being developed. Original designs stored this energy in an electrolytic capacitor for use during flight. Here we replace the electrolytic capacitor with a smaller, lighter, and potentially more reliable electrochemical double layer capacitor (aka, supercapacitor). The potential problems with using supercapacitors in this application are that the piezoelectric output greatly exceeds the supercapacitor electrolyte breakdown voltage, and the frequency greatly exceeds the operating frequency of commercial supercapacitors. Here we have investigated the use of ultrafast vertically oriented graphene array-based supercapacitors for storing the energy in this application. We find that the electrolyte breakdown is not a serious limitation as it is either kinetically limited by the relatively high frequency of the piezoelectric output, or it is overcome by the self-healing nature of supercapacitors. We also find that these supercapacitors have sufficient dynamic response to efficiently store the generated energy.

  3. Nuclear propulsion in high yield vessels

    International Nuclear Information System (INIS)

    Vergara Aimone, Julio

    2000-01-01

    Current developments in advanced ship design brings high-speed maritime transportation closer to reality, aiming to create new markets and to recover a fraction of the high value goods now shipped only by air. High-speed transport is growing at a rate of 15% per year, higher than air transport and at a fraction of air tariffs. Although such growth rate is restricted to passengers and automobiles, there is a potential for high-speed cargo in some routes. A recent proposal is Fast Ship, a 260 m long, 40 m wide concept designed to cruise from Philadelphia to Cherbourg in less that 4 days, for a door-to-door timely cargo delivery of 7 days, thanks to an advanced hull design, and a high power propulsion plant to compensate for weather-related delays. However, almost 40% of the total operation cost would be fuel. This appears to be a natural application for nuclear power, in a similar way to the golden age of this technology. A nuclear Fast Ship would save almost 5000 tons of a fuel per trip, and about half of such spare might be available for additional cargo. Furthermore, operation costs would be smaller and very stable to resource price fluctuation, plus a few other advantages. For other ocean markets, such as the Asia-America route, nuclear power would become a much better choice. This paper discusses the reactor type and layout suitable for such application. The ship designer is aware of the current proposal, although the power pack is not readily available today and its political aspects have not been dealt with. The economy of our nation relies on exports and almost 90% of such flow goes by sea. It is also possible that in the future, Mercosur might have a dependency on such high-speed transport mode and propulsion system (au)

  4. Seed Nutrition and Quality, Seed Coat Boron and Lignin Are Influenced by Delayed Harvest in Exotically-Derived Soybean Breeding Lines under High Heat.

    Science.gov (United States)

    Bellaloui, Nacer; Smith, James R; Mengistu, Alemu

    2017-01-01

    The timing of harvest is a major factor affecting seed quality in soybean, particularly in Midsouthern USA, when rain during harvest period is not uncommon. The objective of this research was to evaluate the effects of time of harvest on soybean seed quality (seed composition, germination, seed coat boron, and lignin) in high germinability (HG) breeding lines (50% exotic) developed under high heat. The hypothesis was that seeds of HG lines possess physiological and genetic traits for a better seed quality at harvest maturity and delayed harvest. A 2-year field experiment was conducted under irrigated conditions. Results showed that, at harvest maturity, the exotic HG lines had higher seed protein, oleic acid, sugars, seed coat boron, and seed coat lignin, but lower seed oil compared with the non-exotic checks (Control), confirming our hypothesis. At 28 days after harvest maturity (delayed harvest), the content of seed protein, oleic acid, sugars, seed coat boron, and seed coat lignin were higher in some of the HG lines compared with the checks, indicating a possible involvement of these seed constituents, especially seed coat boron and seed coat lignin, in maintaining seed coat integrity and protecting seed coat against physical damage. Highly significant positive correlations were found between germination and seed protein, oleic acid, sugars, and seed coat boron and seed coat lignin. Highly significant negative correlation was found between germination and oil, linoleic acid, seed coat wrinkling, shattering, and hard seed. Yields of some HG lines were competitive with checks. This research demonstrated that time of harvesting is an important factor influencing seed protein and oil production. Also, since high oleic acid is desirable for oxidative stability, shelf-life and biodiesel properties, using HG lines could positively influence these important traits. This result should suggest to breeders of some of the advantages of selecting for high seed coat boron and

  5. Added-values of high spatiotemporal remote sensing data in crop yield estimation

    Science.gov (United States)

    Gao, F.; Anderson, M. C.

    2017-12-01

    Timely and accurate estimation of crop yield before harvest is critical for food market and administrative planning. Remote sensing derived parameters have been used for estimating crop yield by using either empirical or crop growth models. The uses of remote sensing vegetation index (VI) in crop yield modeling have been typically evaluated at regional and country scales using coarse spatial resolution (a few hundred to kilo-meters) data or assessed over a small region at field level using moderate resolution spatial resolution data (10-100m). Both data sources have shown great potential in capturing spatial and temporal variability in crop yield. However, the added value of data with both high spatial and temporal resolution data has not been evaluated due to the lack of such data source with routine, global coverage. In recent years, more moderate resolution data have become freely available and data fusion approaches that combine data acquired from different spatial and temporal resolutions have been developed. These make the monitoring crop condition and estimating crop yield at field scale become possible. Here we investigate the added value of the high spatial and temporal VI for describing variability of crop yield. The explanatory ability of crop yield based on high spatial and temporal resolution remote sensing data was evaluated in a rain-fed agricultural area in the U.S. Corn Belt. Results show that the fused Landsat-MODIS (high spatial and temporal) VI explains yield variability better than single data source (Landsat or MODIS alone), with EVI2 performing slightly better than NDVI. The maximum VI describes yield variability better than cumulative VI. Even though VI is effective in explaining yield variability within season, the inter-annual variability is more complex and need additional information (e.g. weather, water use and management). Our findings augment the importance of high spatiotemporal remote sensing data and supports new moderate

  6. High-efficiency passive full wave rectification for electromagnetic harvesters

    Science.gov (United States)

    Yilmaz, Mehmet; Tunkar, Bassam A.; Park, Sangtak; Elrayes, Karim; Mahmoud, Mohamed A. E.; Abdel-Rahman, Eihab; Yavuz, Mustafa

    2014-10-01

    We compare the performance of four types of full-wave bridge rectifiers designed for electromagnetic energy harvesters based on silicon diodes, Schottky diodes, passive MOSFETs, and active MOSFETs. Simulation and experimental results show that MOSFET-type rectifiers are more efficient than diode-type rectifiers, reaching voltage and power efficiency of 99% for ideal voltage source with input amplitudes larger than 800 mV. Since active MOSFETs require extra components and an external DC power supply, we conclude that passive MOSFETs are superior for micro-power energy harvesting systems. We demonstrate passive MOSFET rectifiers implemented using discrete, off-shelf components and show that they outperform all electromagnetic harvester rectifiers hitherto reported obtaining a power efficiency of 95%. Furthermore, we show that passive MOSFET rectifiers do not affect the center frequency, harvesting bandwidth, or optimal resistance of electromagnetic harvesters. We demonstrate a complete power management module by adding a capacitor to the rectifier output terminal. We found that this configuration changed the optimal resistive load from 40 Ω to 55 Ω and decreased output power efficiency to 86%.

  7. A high yield process for hydrate formation

    Energy Technology Data Exchange (ETDEWEB)

    Giavarini, C.; Maccioni, F. [Univ. of Roma La Sapienza, Roma (Italy). Dept. of Chemical Engineering

    2008-07-01

    Due to the large quantities of natural gas stored in deep ocean hydrates, hydrate reservoirs are a substantial energy resource. Hydrates concentrate methane by as much as a factor of 164. As such, several natural gas transportation and storage systems using gas hydrates have been studied, and many of them are nearing practical use. In these systems, the hydrate is produced as a slurry by a spray process at approximately 7 megapascal (MPa), and then shaped into pellets. The use of a spray process, instead of a conventional stirred vessel is necessary in order to reach high hydrate concentrations in the hydrate-ice system. This paper presented a new procedure to produce a bulk of concentrated methane hydrate in a static traditional reactor at moderate pressure, controlling pressure and temperature in the interval between ice melting and the hydrate equilibrium curve. This paper discussed the experimental procedure which included formation of methane hydrate at approximately 5 MPa and 2 degrees Celsius in a reaction calorimeter at a volume of two liters. Results were also discussed. It was concluded that the procedure seemed suitable for the development of a gas hydrate storage and transport technology. It was found that the spray procedure took more time, but could be sped up and made continuous by using two vessels, one for hydrate formation and the other for hydrate concentration. The advantage was the production of a concentrated hydrate, using a simpler equipment and working at lower pressures respect to the spray process. 9 refs., 5 figs.

  8. Variation in the sugar yield in response to drying-off of sugarcane before harvest and the occurrence of low air temperatures

    Directory of Open Access Journals (Sweden)

    Renato Araújo

    2016-03-01

    Full Text Available ABSTRACT The need to irrigate sugarcane in the Brazilian Savanna is due to the lack of rain from April to September. For efficient sugar accumulation, the crop needs water stress or heat stress at the maturation stage. However, when the water deficit is intense at this stage, it occurs the reduction in crop production. The objective of this study was: (i to assess the quality of the raw material of sugarcane in different drying-off seasons before harvest; (ii to evaluate the influence of heat stress on the culture. The experiment was conducted in Santo Antônio de Goiás (GO, Brazil, in Oxisol, with CTC4 variety in cane-plant cycle. A randomized block design in a split-plot array in time was used. The treatments of the plots were five drying-off times (90, 60, 30, 15 and 0 days before harvest and, in the subplots, five seasons of the yield evaluation. Irrigation was carried out by surface drip method, which provided 50% of crop water requirement. The best results for sugar yield occurred 30 days before harvest, period in which the crop irrigation could be interrupted. The water deficit of 37.76 mm appears to be the critical limit of water shortage in the soil, from which the sugarcane yield starts to be reduced. The sugar concentration in the stalk was more influenced by low air temperatures than sugarcane yield.

  9. Effect of Planting Patterns' and Plant Population on Some of Morphological Traits, Harvest Index and Conservable Grain Yield of Sweet Corn

    Directory of Open Access Journals (Sweden)

    M. Nasrolah Alhossini

    2012-04-01

    Full Text Available Sweet corn is one of the most important crops in Iran and due to its short period of growth, it has been an important position after wheat and barley in khorasane Razavi Province. In this study two methods of planting (one raised bed and furrow planting and 3 plant densities (65000, 75000 and 85000 plant/ha was evaluated on some of Morphological Traits, harvest index and conservable grain yield of sweet Corn(Chase and KSC403su Varieties in Torbat-e-Heidarie in saline (4.060ds/m condition on 2009. The experimental design was factorial based on RCBC with 4 replications. The result of ANOVA showed significant differences between Anthesis silking interval (ASI, tassel length, plant height, ear height, stem diameter, harvest index, and conservable grain yield of sweet corn varieties that effected by planting methods. the highest harvest index was belonged to Chase in 75000 Plant/ha on one raised bed planting method with 31.75% and the lowest mean was belonged to KSC403su in 85000 Plant/ha on furrow planting method with 14.93%. In addition the highest grain yield was belonged to chase variety at 75000 plant/ha and furrow planting method with 11.912 ton/ha, while the lowest grain yield was belonged to KSC403su variety at 85000 plant/ha and raised bed planting (3.610 ton/ha. The Chase variety was better than KSC403su Due to its canopy and photo period is shorter than KSC403su. The superiority of Chase variety can be related to better distribution of leaves, highest harvest index, conservable grain yield and plant arrangement in the row.

  10. Picker versus stripper harvesters on the High Plains of Texas

    Science.gov (United States)

    A break even analysis based on NPV was conducted to compare picker-based and stripper-based harvest systems with and without field cleaners. Under no conditions analyzed was the NPV of a stripper system without a field cleaner greater than a stripper system with a field cleaner. Break even curves re...

  11. Biomass yield and greenhouse gas emissions from a drained fen peatland cultivated with reed canary grass under different harvest and fertilizer regimes

    DEFF Research Database (Denmark)

    Kandel, Tanka Prasad; Elsgaard, Lars; Karki, Sandhya

    2013-01-01

    Reed canary grass (RCG, Phalaris arundinacea L.) is a suitable energy crop for cultivation in northern peatlands. However, the atmospheric impact of RCG cultivation as influenced by harvest frequency and fertilization is not clear. Here, we compared the biomass yield and greenhouse gas (GHG......) balance for RCG cultivation in peatlands affected by cutting frequency and fertilizer managements. The managements included one-cut (OC) and two-cut (TC) systems that were either fertilized (TC-F) or unfertilized (TC-U) after the first cut in summer. Biomass yield of OC, TC-F and TC-U were 12, 16 and 11...

  12. Foliar application of molybdenum reduces yield loss and pre-harvest sprouting in japonica rice seed subjected to simulated flooding during seed development and maturation

    OpenAIRE

    Tejakhod, Sujittra; Hammond, John P.; Ellis, Richard H.

    2018-01-01

    Flooding damages rice crops and its incidence is increasing. Foliar spray applications of molybdenum (100, 600 or 3000 mg Mo L-1), abscisic acid (ABA, 50 μM), or deionised water (control) were made to pot-grown plants of the Japonica rice cv. Gleva at flag leaf appearance to determine their effects on seed yield and pre-harvest sprouting after flooding. Plants were submerged , to simulate flooding, for four days from 20 or 30 days after anthesis (DAA). Seed yield per plant, seed weight, and p...

  13. Influences of Harvest Date on Yield, Quality and Resistance to Seed Deterioration of Spring Soybean in South%收获期对南方春大豆产量、品质及抗劣变性的影响

    Institute of Scientific and Technical Information of China (English)

    李小红; 谢运河; 郑贵辰; 阳小凤; 王业建

    2013-01-01

    In this study, the influences of harvest date on the yield, quality and resistance to seed deterioration were studied u-sing four cultivated spring soybean varieties of Hunan province. Results showed we could get the highest 100 - grain seed weight and seed weight per plant at full - ripe stage. If the soybean was harvested too early, the protein content and protein — fat total content in the seed were low. If the soybean was harvested too late, the fat content in the seed was low. Higher germination potential and germination rate of seeds could be harvested at ripening to full - ripe stage. It was also showed that the resistance to seed deterioration of spring soybean was high when the soybean was harvested more early in its harvest period.%通过田间试验,研究了收获期对湖南省主栽的4个春大豆品种产量、品质及抗劣变性的影响.结果表明:在完熟期收获的大豆百粒重和单株粒重均最高;过早收获时种子蛋白质含量、蛋脂总含量低,过迟收获时则脂肪含量低;在成熟期至完熟期收获能获得具有较高发芽势和发芽率的种子;收获期适当提前有利于增强大豆种子的抗劣变性.

  14. High yielding mutants of blackgram variety 'PH-25'

    International Nuclear Information System (INIS)

    Misra, R.C.; Mohapatra, B.D.; Panda, B.S.

    2001-01-01

    Seeds of blackgram (Vigna mungo L.) variety 'PH-5' were treated with chemical mutagens ethyl methanesulfonate (EMS), nitrosoguanidine (NG), maleic hydrazide (MH) and sodium azide (NaN 3 ), each at 3 different concentrations. Thirty six mutant lines developed from mutagenic treatments along with parent varieties were tested in M 4 generation. The mutants showed wide variation in most of the traits and multivariante D 2 analysis showed genetic divergence among themselves. Twenty of the thirty mutants showed genetic divergence from parent. Ten selected high yielding mutants were tested in M 5 . Yield and other productive traits of five high yielding mutants in M 4 and M 5 are presented

  15. High ethanol yields using Aspergillus oryzae koji and corn media

    Energy Technology Data Exchange (ETDEWEB)

    Ziffer, J.; Iosif, M.C.

    1982-01-01

    High ethanol and stillage solids were achieved using whole corn mashes. Ethanol yields of 14% (98.5% of theory) and stillage levels of approximately 23% were obtained in 74-90 hours using mild acid pretreatment with A. oryzae wheat bran koji saccharification. High ethanol yields were also obtained with bacterial amylase, instead of the acid treatment, when the sterilization step was omitted. The implications of ethanol fermentation process modifications are explored.

  16. Advances in Non-Destructive Early Assessment of Fruit Ripeness towards Defining Optimal Time of Harvest and Yield Prediction—A Review

    Directory of Open Access Journals (Sweden)

    Bo Li

    2018-01-01

    Full Text Available Global food security for the increasing world population not only requires increased sustainable production of food but a significant reduction in pre- and post-harvest waste. The timing of when a fruit is harvested is critical for reducing waste along the supply chain and increasing fruit quality for consumers. The early in-field assessment of fruit ripeness and prediction of the harvest date and yield by non-destructive technologies have the potential to revolutionize farming practices and enable the consumer to eat the tastiest and freshest fruit possible. A variety of non-destructive techniques have been applied to estimate the ripeness or maturity but not all of them are applicable for in situ (field or glasshouse assessment. This review focuses on the non-destructive methods which are promising for, or have already been applied to, the pre-harvest in-field measurements including colorimetry, visible imaging, spectroscopy and spectroscopic imaging. Machine learning and regression models used in assessing ripeness are also discussed.

  17. Biogas production from high-yielding energy crops in boreal conditions

    Energy Technology Data Exchange (ETDEWEB)

    Seppala, M.

    2013-11-01

    In this thesis, the methane production potential of traditional and novel energy crops was evaluated in boreal conditions. The highest methane yield per hectare was achieved with maize (4 000-9 200 m{sup 3}CH{sub 4} ha{sup -1} a{sup -1}) and the second highest with brown knapweed (2 700-6 100 m{sup 3}CH{sub 4} ha{sup -1} a{sup -1}). Recently, the most feasible energy crop, grass, produced 1 200-3 600 m{sup 3}CH{sub 4} ha{sup -1} a{sup -1}. The specific methane yields of traditional and novel energy crops varied from 170-500 l kg{sup -1} volatile solid (VS). The highest specific methane yields were obtained with maize, while the novel energy crops were at a lower range. The specific methane yields decreased in the later harvest time with maize and brown knapweed, and the specific methane yield of the grasses decreased from the 1st to 2nd harvests. Maize and brown knapweed produced the highest total solid (TS) yields per hectare 13-23 tTS ha{sup -1}, which were high when compared with the TS yields of grasses (6-13 tTS ha{sup -1}). The feasibility of maize and brown knapweed in co-digestion with liquid cow manure, in continuously stirred tank reactors (CSTR), was evaluated. According to the CSTR runs, maize and brown knapweed are suitable feeds and have stable processes, producing the highest methane yields (organic loading rate 2 kgVS m{sup -3}d{sup -1}), with maize at 259 l kgVS{sup -1} and brown knapweed at 254 l kgVS{sup -1}. The energy balance (input/output) of the cultivation of the grasses, maize and brown knapweed was calculated in boreal conditions, and it was better when the digestate was used as a fertilizer (1.8-4.8 %) than using chemical fertilizers (3.7-16.2 %), whose production is the most energy demanding process in cultivation. In conclusion, the methane production of maize, grasses and novel energy crops can produce high methane yields and are suitable feeds for anaerobic digestion. The cultivation managements of maize and novel energy crops for

  18. Nonlinear vibration analysis of the high-efficiency compressive-mode piezoelectric energy harvester

    Science.gov (United States)

    Yang, Zhengbao; Zu, Jean

    2015-04-01

    Power source is critical to achieve independent and autonomous operations of electronic mobile devices. The vibration-based energy harvesting is extensively studied recently, and recognized as a promising technology to realize inexhaustible power supply for small-scale electronics. Among various approaches, the piezoelectric energy harvesting has gained the most attention due to its high conversion efficiency and simple configurations. However, most of piezoelectric energy harvesters (PEHs) to date are based on bending-beam structures and can only generate limited power with a narrow working bandwidth. The insufficient electric output has greatly impeded their practical applications. In this paper, we present an innovative lead zirconate titanate (PZT) energy harvester, named high-efficiency compressive-mode piezoelectric energy harvester (HC-PEH), to enhance the performance of energy harvesters. A theoretical model was developed analytically, and solved numerically to study the nonlinear characteristics of the HC-PEH. The results estimated by the developed model agree well with the experimental data from the fabricated prototype. The HC-PEH shows strong nonlinear responses, favorable working bandwidth and superior power output. Under a weak excitation of 0.3 g (g = 9.8 m/s2), a maximum power output 30 mW is generated at 22 Hz, which is about ten times better than current energy harvesters. The HC-PEH demonstrates the capability of generating enough power for most of wireless sensors.

  19. Harvest season, high polluted season in East China

    International Nuclear Information System (INIS)

    Huang Xin; Song Yu; Li Mengmeng; Li Jianfeng; Zhu Tong

    2012-01-01

    East China, a major agricultural zone with a dense population, suffers from severe air pollution during June, the agricultural harvest season, every year. Crop burning emits tremendous amounts of combustion products into the atmosphere, not only rapidly degrading the local air quality but also affecting the tropospheric chemistry, threatening public health and affecting climate change. Recently, in mid-June 2012, crop fires left a thick pall of haze over East China. We evaluated the PM 10 , PM 2.5 (particulates less than 10 and 2.5 μm in aerodynamic diameter) and BC (black carbon) emissions by analyzing detailed census data and moderate resolution imaging spectroradiometer (MODIS) remote sensing images and then simulated the consequent pollution using meteorological and dispersion models. The results show that the crop fires sweeping from the south to the north are responsible for the intensive air pollution during harvest season. It is necessary for scientists and governments to pay more attention to this issue. (letter)

  20. Round-Bale Silage Harvesting and Processing Effects on Overwintering Ability, Dry Matter Yield, Fermentation Quality, and Palatability of Dwarf Napiergrass (Pennisetum purpureum Schumach

    Directory of Open Access Journals (Sweden)

    Satoru Fukagawa

    2017-02-01

    Full Text Available Round-bale silage harvesting and processing methods were assessed to evaluate overwintering ability and dry matter (DM yield, fermentation quality and palatability of overwintered dwarf Napiergrass (Pennisetum purpureum Schumach in the two years following establishment in Nagasaki, Japan, in May 2013 using rooted tillers with a density of 2 plants/m2. In 2014, harvesting methods under no-wilting treatment were compared for flail-type harvesting with a round-baler (Flail/baler plot and mower conditioning with a round-baler (Mower/baler plot, which is common for beef-calf–producing farmers in the region. In 2015, the effect of ensilage with wilting was investigated only in the Mower/baler plot. Dwarf Napiergrass was cut twice, in early August (summer and late November (late autumn, each year. The winter survival rate was greater than 96% in May both years. The DM yield in the Mower/baler plot did not differ significantly for the first summer cutting or the annual total from the Flail/baler plot, but did show inferior yield for the second cutting. The fermentation quality of the second-cut plants, estimated using the V2-score, was higher in the Flail/baler plot than in the Mower/baler plot, possibly because of higher air-tightness, and the second-cut silage tended to have better fermentation quality than the first-cut silage in both harvesting plots. Wilting improved the fermentation quality of dwarf Napiergrass silage in summer, but not in autumn. The palatability of the silage, as estimated by alternative and voluntary intake trials using Japanese Black beef cattle, did not differ significantly between plots. The results suggest that dwarf Napiergrass can be better harvested using a mower conditioner with processing by a round-baler, an approach common to beef-calf–producing farmers, than with the flail/baler system, without reducing the persistence, yield, or palatability of the silage. Moreover, wilting treatment improved the fermentation

  1. [Study on High-yield Cultivation Measures for Arctii Fructus].

    Science.gov (United States)

    Liu, Shi-yong; Jiang, Xiao-bo; Wang, Tao; Sun, Ji-ye; Hu, Shang-qin; Zhang, Li

    2015-02-01

    To find out the high yield cultivation measures for Arctii Fructus. Completely randomized block experiment design method was used in the field planting, to analyze the effect of different cultivation way on agronomic characters, phenological phase,quality and quantity of Arctii Fructus. Arctium lappa planted on August 28 had the best results of plant height, thousand seeds weight and yield. The highest yield of Arctii Fructus was got at the density of 1,482 plants/667 m2. Arctiin content was in an increase trend with the planting time delay and planting density increasing. The plant height, thousand seeds weight, yield and arctiin content by split application of fertilizer were significantly higher than that by one-time fertilization. Compared with open field Arctium lappa, plant height, yield, arctiin content and relative water content of plastic film mulching Arctium lappa was higher by 7.74%, 10.87%, 6.38% and 24.20%, respectively. In the topping Arctium lappa, the yield was increased by 11.09%, with 39. 89% less branching number. Early planting time and topping shortened the growth cycle of Arctium lappa plant. The high-yield cultivation measures of Arctii Fructus are: around August 28 to sowing, planting density of 1 482 plants/667 m2, split application of fertilizer for four times, covering film on surface of the soil and topping in bolting.

  2. High altitude species, high profits: can the trade in wild harvested Fritillaria cirrhosa (Liliaceae) be sustained?

    Science.gov (United States)

    Cunningham, A B; Brinckmann, J A; Pei, S-J; Luo, P; Schippmann, U; Long, X; Bi, Y-F

    2018-05-08

    in 2013, China exported over 44 tonnes of F. cirrhosa bulbs to Taiwan and 26.7 tonnes to the Republic of Korea. Extensive commercial use and limited wild stocks result in a high price (2,000 - 3,800 CNY per kg (around US$ 303 -560 per kg in 2017)) for F. cirrhosa bulbs. Prices of cultivated Fritillaria bulbs are much lower (600 - 680 CNY per kg in 2017) than wild harvested bulbs. But due to very specific growth requirements of F. cirrhosa, cultivation is not yet able to meet total demand. The consequence is continued exploitation of wild stocks. At the same time, however, an increasing proportion of the demand is met by cultivation of alternative Fritillaria species that are easier to grow than F. cirrhosa. The air-dry mass of F. cirrhosa bulbs varies between 0.0917 - 0.1116g per bulb. This represents 8960 - 10900 bulbs/kg or 8.9 - 10.9 million bulbs per tonne. Current demand therefore represents billions of bulbs per year. Demand for F. cirrhosa bulbs, particularly from China, makes this species one of the most intensively harvested alpine Himalayan medicinal bulbs. Although F. cirrhosa is listed as a Class III protected species in China, billions of these tiny, wild harvested bulbs are sold per year. Due to demand exceeding supply, the price of F. cirrhosa bulbs has increased dramatically. Between 2002 and 2017, for example, the price of wild harvested F. cirrhosa bulbs increased over nine-fold, from the equivalent of US$60 in 2002 to US$560 per kg in 2017. To date, cultivation has been unable to meet the entire market demand for F. cirrhosa bulbs, although other Fritillaria species are successfully cultivated on a larger scale. Copyright © 2018. Published by Elsevier B.V.

  3. Optimization of Dithionite Bleaching of High Yield Bagasse Pulp

    International Nuclear Information System (INIS)

    Mohamed, E.

    2005-01-01

    High yield bagasse pulp was prepared by soaking bagasse in 10 % cold sodium hydroxide for 24 hours and then refluxing for two hours at 95 degree C. Optimization of dithionite bleaching was attained by investigation of different parameters as consistency, temperature, time and ph. Effect of additives as chelating agent (EDTA) or stabilizing of bleaching solution (Zn compound and hexamethylene tetramine) was considered. The effect of air content was also studied. One and two stages bleaching of the pulp were investigated by using sodium dithionite (D) as a sole bleaching agent or after application of one stage bleaching by hydrogen peroxide to attain high brightness for high yield pulp

  4. Early lactation feed intake and milk yield responses of dairy cows offered grass silages harvested at early maturity stages

    DEFF Research Database (Denmark)

    Randby, A T; Weisbjerg, M R; Nørgaard, P

    2012-01-01

    was available in automatic feed stations. Intake of grass silage when fed as the sole feed was 16.9 kg of DM on average for lactation wk 1 to 16. When H1 was supplemented with 4 or 8 kg of concentrates, silage DM intake did not change, but total DM intake increased to 20.6 and 23.7 kg/d, respectively. Energy......The main objective was to evaluate the potential of grass silages of very high quality to support a high milk yield with a low or moderate, or even without concentrate supplementation. Production responses to increased levels of concentrate supplementation with 3 primary growth grass silages...... differing in digestibility were studied using 66 Norwegian Red dairy cows. Roundbale silage was produced from a timothy-dominated sward at very early (H1), early (H2), and normal (H3) stages of crop maturity. Crops were rapidly wilted (h) and a formic acid-based additive was applied. All silages were...

  5. Development of High Yield Feedstocks and Biomass Conversion Technology for Renewable Energy

    Energy Technology Data Exchange (ETDEWEB)

    Hashimoto, Andrew G. [Univ. of Hawaii, Honolulu, HI (United States); Crow, Susan [Univ. of Hawaii, Honolulu, HI (United States); DeBeryshe, Barbara [Univ. of Hawaii, Honolulu, HI (United States); Ha, Richard [Hamakua Springs County Farms, Hilo, HI (United States); Jakeway, Lee [Hawaiian Commercial and Sugar Company, Puunene, HI (United States); Khanal, Samir [Univ. of Hawaii, Honolulu, HI (United States); Nakahata, Mae [Hawaiian Commercial and Sugar Company, Puunene, HI (United States); Ogoshi, Richard [Univ. of Hawaii, Honolulu, HI (United States); Shimizu, Erik [Univ. of Hawaii, Honolulu, HI (United States); Stern, Ivette [Univ. of Hawaii, Honolulu, HI (United States); Turano, Brian [Univ. of Hawaii, Honolulu, HI (United States); Turn, Scott [Univ. of Hawaii, Honolulu, HI (United States); Yanagida, John [Univ. of Hawaii, Honolulu, HI (United States)

    2015-04-09

    This project had two main goals. The first goal was to evaluate several high yielding tropical perennial grasses as feedstock for biofuel production, and to characterize the feedstock for compatible biofuel production systems. The second goal was to assess the integration of renewable energy systems for Hawaii. The project focused on high-yield grasses (napiergrass, energycane, sweet sorghum, and sugarcane). Field plots were established to evaluate the effects of elevation (30, 300 and 900 meters above sea level) and irrigation (50%, 75% and 100% of sugarcane plantation practice) on energy crop yields and input. The test plots were extensive monitored including: hydrologic studies to measure crop water use and losses through seepage and evapotranspiration; changes in soil carbon stock; greenhouse gas flux (CO2, CH4, and N2O) from the soil surface; and root morphology, biomass, and turnover. Results showed significant effects of environment on crop yields. In general, crop yields decrease as the elevation increased, being more pronounced for sweet sorghum and energycane than napiergrass. Also energy crop yields were higher with increased irrigation levels, being most pronounced with energycane and less so with sweet sorghum. Daylight length greatly affected sweet sorghum growth and yields. One of the energy crops (napiergrass) was harvested at different ages (2, 4, 6, and 8 months) to assess the changes in feedstock characteristics with age and potential to generate co-products. Although there was greater potential for co-products from younger feedstock, the increased production was not sufficient to offset the additional cost of harvesting multiple times per year. The feedstocks were also characterized to assess their compatibility with biochemical and thermochemical conversion processes. The project objectives are being continued through additional support from the Office of Naval Research, and the Biomass Research and Development

  6. Improving adaptation to drought stress in white pea bean (Phaseolus vulgaris L): genotypic effects on grain yield, yield components and pod harvest index

    Science.gov (United States)

    Common bean (Phaseolus vulgaris L.) is the most important food legume crop in Africa and Latin America where rainfall pattern is unpredictable. The objectives were to identify better yielding common bean lines with good canning quality under drought, and to identify traits that could be used as sele...

  7. Neutron emission and fragment yield in high-energy fission

    International Nuclear Information System (INIS)

    Grudzevich, O. T.; Klinov, D. A.

    2013-01-01

    The KRIS special library of spectra and emission probabilities in the decays of 1500 nuclei excited up to energies between 150 and 250 MeV was developed for correctly taking into account the decay of highly excited nuclei appearing as fission fragments. The emission of neutrons, protons, and photons was taken into account. Neutron emission fromprimary fragments was found to have a substantial effect on the formation of yields of postneutron nuclei. The library was tested by comparing the calculated and measured yields of products originating from the fission of nuclei that was induced by high-energy protons. The method for calculating these yields was tested on the basis of experimental data on the thermal-neutroninduced fission of 235 U nuclei

  8. High yielding and early maturing mutants in mungbean (Vigna radiata (L) Wilczek)

    International Nuclear Information System (INIS)

    Malik, I.A.

    1988-01-01

    Mungbean in Pakistan is grown on about 79 thousand hectares with an annual production of around 39600 t. The poor yield of cultivars may be largely due to their indeterminate excessive vegetative growth, low harvest index, and susceptibility to various diseases. Lack of synchrony in maturity and pod shattering are also limiting factors. Mutation breeding of mungbean at NIAB has the object of evolving early and uniform maturing high yielding mutants. Seeds of mungbean strains Pak-22 and RC71-27 were irradiated with 60 Co gamma rays (5 kR to 80 kR) in 1977. After selecting mutants in the M 2 , further selections were made in M 3 for earliness, uniform maturity, short plant stature and larger number of pods/plant. In the M 4 , 62 selections were subjected to micro plot yield trials and seed protein analysis. Selection was continued in the advanced generations and performance was studied in multilocational trials arranged through the Department of Agriculture. The important characteristics of two mutants namely NM19-19 (derivative of strain Pak 22 at 40 kR) and NM121-25 (derivative of strain RC71-27 at 20 kR) are listed and their field performance is summarized. Both the mutants are short statured and have erect determinate growth habit. They mature early by a margin of 16 days and yield higher. The high harvest index of the mutants indicates their efficiency in partitioning photosynthates towards grain formation. Because of their synchrony in maturity and top fruit bearing habit the mutants are amenable to mechanized harvesting. The early maturity in mutants also makes them more suitable for intercropping practices. The mutants possess greater degree of tolerance to yellow mosaic disease and have shown wide adaptability and stability when grown under different agroclimatic conditions. Both the mutants have been released in 1986, by the Punjab Seed Council as commercial varieties under the names of 'NIAB Mung 121-25' and 'NIAB Mung 19-19' respectively

  9. Low cost, high yield IFE reactors: Revisiting Velikhov's vaporizing blankets

    International Nuclear Information System (INIS)

    Logan, B.G.

    1992-01-01

    The performance (efficiency and cost) of IFE reactors using MHD conversion is explored for target blanket shells of various materials vaporized and ionized by high fusion yields (5 to 500 GJ). A magnetized, prestressed reactor chamber concept is modeled together with previously developed models for the Compact Fusion Advanced Rankine II (CFARII) MHD Balance-of-Plant (BoP). Using conservative 1-D neutronics models, high fusion yields (20 to 80 GJ) are found necessary to heat Flibe, lithium, and lead-lithium blankets to MHD plasma temperatures, at initial solid thicknesses sufficient to capture most of the fusion yield. Advanced drivers/targets would need to be developed to achieve a ''Bang per Buck'' figure-of-merit approx-gt 20 to 40 joules yield per driver $ for this scheme to be competitive with these blanket materials. Alternatively, more realistic neutronics models and better materials such as lithium hydride may lower the minimum required yields substantially. The very low CFARII BoP costs (contributing only 3 mills/kWehr to CoE) allows this type of reactor, given sufficient advances that non-driver costs dominate, to ultimately produce electricity at a much lower cost than any current nuclear plant

  10. Setting the Record Straight on "High-Yield" Strategies

    Science.gov (United States)

    Marzano, Robert J.

    2009-01-01

    Widely credited with proposing nine "high-yield" instructional strategies, author Robert J. Marzano sets the record straight about the broader number of strategies identified by the research. He provides a list of 41 strategies and suggests more nuanced ways of using, observing, and evaluating them. (Contains 1 figure.)

  11. Executive Summary High-Yield Scenario Workshop Series Report

    Energy Technology Data Exchange (ETDEWEB)

    Leslie Park Ovard; Thomas H. Ulrich; David J. Muth Jr.; J. Richard Hess; Steven Thomas; Bryce Stokes

    2009-12-01

    To get a collective sense of the impact of research and development (R&D) on biomass resource availability, and to determine the feasibility that yields higher than baseline assumptions used for past assessments could be achieved to support U.S. energy independence, an alternate “High-Yield Scenario” (HYS) concept was presented to industry experts at a series of workshops held in December 2009. The workshops explored future production of corn/agricultural crop residues, herbaceous energy crops (HECs), and woody energy crops (WECs). This executive summary reports the findings of that workshop.

  12. Path coefficient and correlation of yield and yield associated traits in candidate bread wheat (triticum aestivum l)lines

    International Nuclear Information System (INIS)

    Muhammad, T.; Haider, S.; Qureshi, M. J.; Shah, G. S.; Zamir, R.

    2005-01-01

    Yield and yield contributing traits were studied in candidate bread wheat lines to find out the genetic contribution of the different characters towards grain yield at NIFA, Peshawar during 2001-02. All the characteristics studied differed significantly from each other. Days to heading showed negative and significant correlation with harvest index and grain yield but was negative and non-significant with the biological yield. Days to maturity were negatively correlated at both genotypic and phenotypic levels with biological yield; harvest index and grain yield and level of correlations were significant with harvest index and grain yield. Plant height showed negative genotypic and phenotypic correlation with harvest index and grain yield. Biological yield had positive and significant genotypic and phenotypic correlations with harvest index and grain yield. Harvest index had positive and highly significant genotypic and phenotypic correlation with grain yield. Genotypic and phenotypic correlation coefficients revealed that important characters influencing grain yield are harvest index and biological yield. Path analysis showed the importance in order of harvest index, biological yield, plant height, days to maturity and days to heading with grain yield. (author)

  13. Breeding for earliness, high yield and disease resistance in rice by means of induced mutations

    Energy Technology Data Exchange (ETDEWEB)

    Haq, M S; Ali, S M; Maniruzzaman, A F.M.; Mansur, A; Islam, R [Atomic Energy Centre, Dacca (Pakistan)

    1970-03-01

    Ten varieties of Boro, Aus and Aman rice were treated with 30 kR of gamma rays from the 500-Ci {sup 60}Co source of the Atomic Energy Centre of Dacca. In addition, two rice varieties were treated with EMS and dES. To suppress tillering, the seeds were sown late and at a high seed rate. 300 normal-looking fertile M{sub 1} plants from each variety were harvested at random. The M{sub 2} progenies were sown on a plant-to-row basis to select for high yield, earliness, blast resistance and response to large doses of nitrogen fertilizer. Characters like plant height, number of tillers, fertile tillers, length of panicle and time from sowing to maturity were checked. As the results showed great variability in the mutagen-treated material the chances for successful selection are promising. (author)

  14. Reducing Severity of Late Blight (Phytophthora infestans and Improving Potato (Solanum tuberosum L. Tuber Yield with Pre-Harvest Application of Calcium Nutrients

    Directory of Open Access Journals (Sweden)

    Yewubnesh Wendimu Seifu

    2017-10-01

    Full Text Available The efficiency of pre-harvest application of calcium chloride alone, calcium nitrate alone, and combined application of calcium chloride and calcium nitrate (1:1 was evaluated in reducing the severity of P. infestans and improving potato tuber yield. Pot experiment was conducted in randomized complete block design with four replications. The treatments consisted of combination of two potato varieties (Shenkola and Gera and three types of calcium nutrients (calcium chloride alone, calcium nitrate alone, and calcium chloride mixed with calcium nitrate, each at three levels (5, 10, and 15 g per liter per plant and the control treatment (0 g of calcium nutrients. In comparison to the control treatment, the application of calcium nutrients significantly decreased the severity of late blight disease and improved potato tuber yield. The effect of calcium nutrients on the severity of late blight disease and potato tuber yield differed among the two potato varieties. The maximum severity reduction (60% was noticed in the Gera potato variety with the application of calcium chloride mixed with calcium nitrate (1:1, supplied at 15 g per plant. However, the highest average tuber yield was obtained with the application of calcium nitrate at 15 g per plant, and average tuber yield was increased by 77% in both potato varieties. Hence, foliar application of either calcium nitrate alone or calcium nitrate mixed with calcium chloride was found to be more efficient than the application of calcium chloride alone. This result suggests that the nitrate ion present in the calcium nitrate may make a difference in terms of reducing the severity of late blight disease and improving potato tuber yield. The lowered severity of late blight disease and the increased tuber yield in potato plants sprayed with calcium nutrients may be because of the higher accumulation of calcium in the plant tissue.

  15. A high yielding, better quality chickpea mutant variety 'NIFA-95'

    International Nuclear Information System (INIS)

    Hassan, S.; Javed, M.A.; Khattak, S.U.K.; Iqbal, M.M.

    2001-01-01

    Chickpea or gram (Cicer arietinum L.) is an important legume crop of Pakistan, grown on over one million hectares annually. The national average yield of the crop is very low (0.5 t/ha) and thus the country had to spent about 2 billion rupees ($ 50 million) on import of pulses. The main causes of low yield are non-availability of genetic sources for resistance to various diseases especially gram blight Ascochyta rabiei (Pass.) Lab., insect pest (Pod borer) and non-adoption of proper production technology by the farmers. This calls for earnest efforts of breeders to evolve high yielding and disease resistant varieties of chickpea for provision of quality seeds to the farming community to increase production of this important crop. Seeds of a highly blight susceptible variety '6153' were irradiated at 200 Gy dose of gamma radiation in 1985 and the promising mutant line CMN-446-4 was selected in M3 generation on the basis of disease resistance, greater number of pods and better plant type. After confirmation of its resistance to blight in M 4 and M 5 , the mutant line was evaluated in various trials at different locations. In the advanced and zonal yield trials during 1993-95, the line CMN-446-4 produced the highest grain yield of 2,600 kg/ha as compared to the rest of the mutants and varieties. The line was also evaluated in the chickpea national uniform yield trial, conducted on over 11 locations in the country during 1993-94. In this trial, the mutant line ranked 3rd by producing an average yield of 1,528 kg/ha as compared to the two check varieties 'Punjab-91' (1,316 kg/ha) and 'Paidar-91' (1,391 kg/ha). The mutant line CMN-446-4 is moderately resistant to gram blight, highly resistant to stored pest (pulse beetle), contains 25.3% more protein as compared to the parental variety 6153 and is also better in nitrogen fixing capacity.The proposal for release of the mutant line CMN-446-4 as a new variety under the name 'NIFA-95' for general cultivation in the rainfed

  16. Impedance Based Characterization of a High-Coupled Screen Printed PZT Thick Film Unimorph Energy Harvester

    DEFF Research Database (Denmark)

    Lei, Anders; Xu, R.; Borregaard, L. M.

    2014-01-01

    The single degree of freedom mass-spring-damper system is the most common approach for deriving a full electromechanical model for the piezoelectric vibration energy harvester. In this paper, we revisit this standard electromechanical model by focusing on the impedance of the piezoelectric device...... parameters which, by means of the piezoelectric impedance expression, all can be determined accurately by electrical measurements. It is shown how four of five lumped parameters can be determined from a single impedance measurement scan, considerably reducing the characterization effort. The remaining...... parameter is determined from shaker measurements, and a highly accurate agreement is found between model and measurements on a unimorph MEMS-based screen printed PZT harvester. With a high coupling term K-2 Q similar or equal to 7, the harvester exhibits two optimum load points. The peak power performance...

  17. High-yield criteria for panoramic radiography. Final report

    International Nuclear Information System (INIS)

    White, S.C.; Forsythe, A.B.

    1982-06-01

    Panoramic radiographs should be obtained when the examination offers the prospect of providing information that will assist in patient care. The purpose of this study was to determine whether high-yield criteria could be developed for the use of panoramic radiographs in the treatment planning of patients seeking dental care. Clinicians were asked what signs or symptoms caused them to order a panoramic radiograph upon patient admission into the UCLA Dental Clinic. At the time the patient was radiographed, a variety of demographic and clinical measures were recorded. The most important high-yield criterion for the panoramic examination is whether the radiograph is ordered for 'general screening examination' (a negative predictor) and whether the radiograph was ordered for any specific examination (a positive predictor). The use of these (or any other) decision rules required clinical judgment of the costs (social and economic) of a missed positive finding relative to that of an unproductive examination

  18. Live growth performance, carcass grading characteristics, and harvest yields of beef steers supplemented zilpaterol hydrochloride and offered ad libitum or maintenance energy intake.

    Science.gov (United States)

    Judy Walter, Lee-Anne; Schmitz, Angela Nicole; Nichols, Wade Taylor; Hutcheson, John Paul; Lawrence, Ty Ellis

    2018-05-04

    A trial was conducted to examine live growth efficiency, harvest yields, and carcass grading performance of steers fed at maintenance (M) or at ad libitum (A) level of intake during zilpaterol hydrochloride (Z) supplementation. Single-sired, beef steers (n = 56; start of trial BW 590 ± 36 kg) blocked (n = 2) by weight and terminal implant were sorted into pairs (n = 14 per block) by weight. Pairs of steers were initially assigned to 0, 28, or 56 d of feeding. Within 28 or 56 d, pairs were assigned to M or A intake. Steers within a pair assigned to 56 d of feeding were randomly assigned to either 20 d of Z supplementation (90 mg/d per steer) with a 4 d withdrawal period prior to slaughter or to no ZH supplementation (C). Steers were housed and fed in individual pens. Weights of all non-carcass and carcass components were recorded at slaughter; carcasses were graded 24-h postmortem. Data were analyzed via a mixed model; the fixed effect was treatment combination with random effects of block and pair. Live growth data used harvest day as the repeated measure and animal as the subject. Single df contrasts were constructed for day 0 vs. day 28, day 0 vs. day 56, day 28 vs. day 56, M vs. A, and C vs. Z. Treatment impacted (P ≤ 0.05) live ADG; contrasts indicated A (1.33) was greater than M (0.14 kg), and Z (1.12) was greater than C (0.82 kg). Similarly, carcass ADG differences (P carcass and internal cavity mass (P carcass yield was greater (P carcass growth, carcass transfer, kill yields, and carcass characteristics across time.

  19. Adipose tissue-derived mesenchymal stem cell yield and growth characteristics are affected by the tissue-harvesting procedure

    NARCIS (Netherlands)

    Oedayrajsingh-Varma, M. J.; van Ham, S. M.; Knippenberg, M.; Helder, M. N.; Klein-Nulend, J.; Schouten, T. E.; Ritt, M. J. P. F.; van Milligen, F. J.

    2006-01-01

    Adipose tissue contains a stromal vascular fraction that can be easily isolated and provides a rich source of adipose tissue-derived mesenchymal stem cells (ASC). These ASC are a potential source of cells for tissue engineering. We studied whether the yield and growth characteristics of ASC were

  20. Evaluation of the body condition of high yielding cows

    OpenAIRE

    Grubić G.; Novaković Ž.; Aleksić S.; Sretenović Lj.; Pantelić V.; Ostojić-Andrić D.

    2009-01-01

    Problems which relate to production, health and reproduction in herds of high yielding cows very often occur due to insufficient knowledge and monitoring of energy reserves in cow organisms. Many researches and practical experiences in this field indicate significant relation between body condition and achieved results in production. Body condition of heads of cattle in certain stages of production cycle is important parameter of applied nutrition, but also entire technological procedure. In ...

  1. Impedance Matching Antenna-Integrated High-Efficiency Energy Harvesting Circuit

    Science.gov (United States)

    Shinki, Yuharu; Shibata, Kyohei; Mansour, Mohamed

    2017-01-01

    This paper describes the design of a high-efficiency energy harvesting circuit with an integrated antenna. The circuit is composed of series resonance and boost rectifier circuits for converting radio frequency power into boosted direct current (DC) voltage. The measured output DC voltage is 5.67 V for an input of 100 mV at 900 MHz. Antenna input impedance matching is optimized for greater efficiency and miniaturization. The measured efficiency of this antenna-integrated energy harvester is 60% for −4.85 dBm input power and a load resistance equal to 20 kΩ at 905 MHz. PMID:28763043

  2. Vibration-based energy harvesting with piezoelectrets having high d{sub 31} activity

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, X. [Institute for Telecommunications Technology, Technische Universität Darmstadt, Merckstr. 25, 64283 Darmstadt (Germany); School of Physics Science and Engineering, Tongji University, Siping Road 1239, Shanghai 200092 (China); Pondrom, P. [Institute for Telecommunications Technology, Technische Universität Darmstadt, Merckstr. 25, 64283 Darmstadt (Germany); System Reliability and Machine Acoustics SzM, Technische Universität Darmstadt, Magdalenenstr. 4, 64289 Darmstadt (Germany); Wu, L. [School of Physics Science and Engineering, Tongji University, Siping Road 1239, Shanghai 200092 (China); Sessler, G. M., E-mail: g.sessler@nt.tu-darmstadt.de [Institute for Telecommunications Technology, Technische Universität Darmstadt, Merckstr. 25, 64283 Darmstadt (Germany)

    2016-05-09

    Sandwiched fluoroethylene propylene films with charged, parallel-tunnel voids between the layers, which exhibit high d{sub 31} piezoelectric activity, were designed. Stripes of such piezoelectrets were exposed to mechanical stress in length direction by a seismic mass excited to vibrations. Due to the piezoelectricity of the films, a current in a terminating resistor is generated. The harvested power across the resistor amounts to about 0.2 mW for a seismic mass of 2 g and an acceleration of 1 g. In comparison with other piezoelectret or with poly(vinylidene fluoride) harvesters, the generated power referred to equal acceleration and force, is significantly larger.

  3. Impedance Matching Antenna-Integrated High-Efficiency Energy Harvesting Circuit

    Directory of Open Access Journals (Sweden)

    Yuharu Shinki

    2017-08-01

    Full Text Available This paper describes the design of a high-efficiency energy harvesting circuit with an integrated antenna. The circuit is composed of series resonance and boost rectifier circuits for converting radio frequency power into boosted direct current (DC voltage. The measured output DC voltage is 5.67 V for an input of 100 mV at 900 MHz. Antenna input impedance matching is optimized for greater efficiency and miniaturization. The measured efficiency of this antenna-integrated energy harvester is 60% for −4.85 dBm input power and a load resistance equal to 20 kΩ at 905 MHz.

  4. Impedance Matching Antenna-Integrated High-Efficiency Energy Harvesting Circuit.

    Science.gov (United States)

    Shinki, Yuharu; Shibata, Kyohei; Mansour, Mohamed; Kanaya, Haruichi

    2017-08-01

    This paper describes the design of a high-efficiency energy harvesting circuit with an integrated antenna. The circuit is composed of series resonance and boost rectifier circuits for converting radio frequency power into boosted direct current (DC) voltage. The measured output DC voltage is 5.67 V for an input of 100 mV at 900 MHz. Antenna input impedance matching is optimized for greater efficiency and miniaturization. The measured efficiency of this antenna-integrated energy harvester is 60% for -4.85 dBm input power and a load resistance equal to 20 kΩ at 905 MHz.

  5. Highly transparent triboelectric nanogenerator for harvesting water-related energy reinforced by antireflection coating

    Science.gov (United States)

    Liang, Qijie; Yan, Xiaoqin; Gu, Yousong; Zhang, Kui; Liang, Mengyuan; Lu, Shengnan; Zheng, Xin; Zhang, Yue

    2015-03-01

    Water-related energy is an inexhaustible and renewable energy resource in our environment, which has huge amount of energy and is not largely dictated by daytime and sunlight. The transparent characteristic plays a key role in practical applications for some devices designed for harvesting water-related energy. In this paper, a highly transparent triboelectric nanogenerator (T-TENG) was designed to harvest the electrostatic energy from flowing water. The instantaneous output power density of the T-TENG is 11.56 mW/m2. Moreover, with the PTFE film acting as an antireflection coating, the maximum transmittance of the fabricated T-TENG is 87.4%, which is larger than that of individual glass substrate. The T-TENG can be integrated with silicon-based solar cell, building glass and car glass, which demonstrates its potential applications for harvesting waste water energy in our living environment and on smart home system and smart car system.

  6. Robust piezoelectric composites for energy harvesting in high-strain environments

    NARCIS (Netherlands)

    Ende, D.A. van der; Groen, W.A.; Zwaag, S. van der

    2013-01-01

    High-strain environments, such as are found in automobile tires, provide deformation energy that can be harvested using piezoelectric materials, for instance, for powering electronics such as wireless sensors. Despite numerous efforts, none of the present devices easily satisfy the stringent

  7. Phytoremediation of high phosphorus soil by annual ryegrass and common bermudagrass harvest

    Science.gov (United States)

    Removal of soil phosphorus (P) in crop harvest is a remediation option for soils high in P. This four-year field-plot study determined P uptake by annual ryegrass (ARG, Lolium multiflorum Lam.) and common bermudagrass (CB, Cynodon dactylon (L.) Pers.) from Ruston soil (fine-loamy, siliceous, thermic...

  8. Novel Semiconducting Polymers for Highly Efficient Solar Energy Harvesting

    Science.gov (United States)

    2014-03-11

    we have developed an effective approach to enhance PCE and achieved an unprecedented high PCE value around 9.4%. S SS S X O O S SO OS S X S S X...Address: 128.135.225.61 Language: English (en-us,en;q=0.7,zh-cn;q=0.3) User Agent: Mozilla/5.0 (Windows NT 5.1; rv:27.0) Gecko/20100101 Firefox /27.0 Http

  9. Effects of Physical Seed Priming and Hydropriming on Physiological and Morphological Characteristics, Yield and Harvest Index in Marigold (Calendula officinalis L.

    Directory of Open Access Journals (Sweden)

    S. Baser Kouchebagh

    2014-03-01

    Full Text Available To study the effect of different seed treatments on germination of calendula, an experiment conducted in field with complete randomized block design and three replications, at Agricultural Research Station of Islamic Azad University, Tabriz Branch in 2013. Treatments were: treating the most seeds by ultrasonic with maximum (3 w.m-2 and gamma and beta by 2 µc for 10 minutes, laser by 6328A° and magnetic field by 40 MT for 5, 10 and 15 minutes hydro-priming for 24 hours and control. Results indicate that maximum flower yield (13.85g was produced by seeds treated with laser irradiation for 15 minutes as compared to that of control (4.34g. Highest biologic yield belonged to seeds treated with magnetic field for 10 minutes (33.20 g.m-2 and lowest to control (7.89 g.m-2. Highest harvest index was obtained from seeds treated by gamma irradiation for 10 minutes (69.07 and lowest for 15 minutes (18.81. It may be suggested that marigold growers may improve crop yield by priming the seeds with magnetic field and laser irradiation before sowing.

  10. Image Harvest: an open-source platform for high-throughput plant image processing and analysis.

    Science.gov (United States)

    Knecht, Avi C; Campbell, Malachy T; Caprez, Adam; Swanson, David R; Walia, Harkamal

    2016-05-01

    High-throughput plant phenotyping is an effective approach to bridge the genotype-to-phenotype gap in crops. Phenomics experiments typically result in large-scale image datasets, which are not amenable for processing on desktop computers, thus creating a bottleneck in the image-analysis pipeline. Here, we present an open-source, flexible image-analysis framework, called Image Harvest (IH), for processing images originating from high-throughput plant phenotyping platforms. Image Harvest is developed to perform parallel processing on computing grids and provides an integrated feature for metadata extraction from large-scale file organization. Moreover, the integration of IH with the Open Science Grid provides academic researchers with the computational resources required for processing large image datasets at no cost. Image Harvest also offers functionalities to extract digital traits from images to interpret plant architecture-related characteristics. To demonstrate the applications of these digital traits, a rice (Oryza sativa) diversity panel was phenotyped and genome-wide association mapping was performed using digital traits that are used to describe different plant ideotypes. Three major quantitative trait loci were identified on rice chromosomes 4 and 6, which co-localize with quantitative trait loci known to regulate agronomically important traits in rice. Image Harvest is an open-source software for high-throughput image processing that requires a minimal learning curve for plant biologists to analyzephenomics datasets. © The Author 2016. Published by Oxford University Press on behalf of the Society for Experimental Biology.

  11. Image Harvest: an open-source platform for high-throughput plant image processing and analysis

    Science.gov (United States)

    Knecht, Avi C.; Campbell, Malachy T.; Caprez, Adam; Swanson, David R.; Walia, Harkamal

    2016-01-01

    High-throughput plant phenotyping is an effective approach to bridge the genotype-to-phenotype gap in crops. Phenomics experiments typically result in large-scale image datasets, which are not amenable for processing on desktop computers, thus creating a bottleneck in the image-analysis pipeline. Here, we present an open-source, flexible image-analysis framework, called Image Harvest (IH), for processing images originating from high-throughput plant phenotyping platforms. Image Harvest is developed to perform parallel processing on computing grids and provides an integrated feature for metadata extraction from large-scale file organization. Moreover, the integration of IH with the Open Science Grid provides academic researchers with the computational resources required for processing large image datasets at no cost. Image Harvest also offers functionalities to extract digital traits from images to interpret plant architecture-related characteristics. To demonstrate the applications of these digital traits, a rice (Oryza sativa) diversity panel was phenotyped and genome-wide association mapping was performed using digital traits that are used to describe different plant ideotypes. Three major quantitative trait loci were identified on rice chromosomes 4 and 6, which co-localize with quantitative trait loci known to regulate agronomically important traits in rice. Image Harvest is an open-source software for high-throughput image processing that requires a minimal learning curve for plant biologists to analyzephenomics datasets. PMID:27141917

  12. Magnetostrictive clad steel plates for high-performance vibration energy harvesting

    Science.gov (United States)

    Yang, Zhenjun; Nakajima, Kenya; Onodera, Ryuichi; Tayama, Tsuyoki; Chiba, Daiki; Narita, Fumio

    2018-02-01

    Energy harvesting technology is becoming increasingly important with the appearance of the Internet of things. In this study, a magnetostrictive clad steel plate for harvesting vibration energy was proposed. It comprises a cold-rolled FeCo alloy and cold-rolled steel joined together by thermal diffusion bonding. The performances of the magnetostrictive FeCo clad steel plate and conventional FeCo plate cantilevers were compared under bending vibration; the results indicated that the clad steel plate construct exhibits high voltage and power output compared to a single-plate construct. Finite element analysis of the cantilevers under bending provided insights into the magnetic features of a clad steel plate, which is crucial for its high performance. For comparison, the experimental results of a commercial piezoelectric bimorph cantilever were also reported. In addition, the cold-rolled FeCo and Ni alloys were joined by thermal diffusion bonding, which exhibited outstanding energy harvesting performance. The larger the plate volume, the more the energy generated. The results of this study indicated not only a promising application for the magnetostrictive FeCo clad steel plate as an efficient energy harvester, related to small vibrations, but also the notable feasibility for the formation of integrated units to support high-power trains, automobiles, and electric vehicles.

  13. High-yield synthesis and optical response of gold nanostars

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, Pandian Senthil [Departamento de Quimica Fisica and Unidad Asociada CSIC-Universidade de Vigo, 36310 Vigo (Spain); Pastoriza-Santos, Isabel [Departamento de Quimica Fisica and Unidad Asociada CSIC-Universidade de Vigo, 36310 Vigo (Spain); RodrIguez-Gonzalez, Benito [Departamento de Quimica Fisica and Unidad Asociada CSIC-Universidade de Vigo, 36310 Vigo (Spain); Abajo, F Javier GarcIa de [Instituto de Optica-CSIC, Serrano 121, 28006 Madrid (Spain); Liz-Marzan, Luis M [Departamento de Quimica Fisica and Unidad Asociada CSIC-Universidade de Vigo, 36310 Vigo (Spain)

    2008-01-09

    Multipod Au nanoparticles (nanostars) with single crystalline tips were synthesized in extremely high yield through the reduction of HAuCl{sub 4} in a concentrated solution of poly(vinylpyrrolidone) (PVP) in N,N-dimethylformamide (DMF), in the presence of preformed Au nanoparticle seeds, but with no need for external energy sources. Nanostar dispersions display a well-defined optical response, which was found (through theoretical modeling) to comprise a main mode confined within the tips and a secondary mode confined in the central body. Calculations of the surface enhanced Raman scattering (SERS) response additionally show that this morphology will be relevant for sensing applications.

  14. High-yield synthesis and optical response of gold nanostars

    Science.gov (United States)

    Senthil Kumar, Pandian; Pastoriza-Santos, Isabel; Rodríguez-González, Benito; García de Abajo, F. Javier; Liz-Marzán, Luis M.

    2008-01-01

    Multipod Au nanoparticles (nanostars) with single crystalline tips were synthesized in extremely high yield through the reduction of HAuCl4 in a concentrated solution of poly(vinylpyrrolidone) (PVP) in N,N-dimethylformamide (DMF), in the presence of preformed Au nanoparticle seeds, but with no need for external energy sources. Nanostar dispersions display a well-defined optical response, which was found (through theoretical modeling) to comprise a main mode confined within the tips and a secondary mode confined in the central body. Calculations of the surface enhanced Raman scattering (SERS) response additionally show that this morphology will be relevant for sensing applications.

  15. High-yield synthesis and optical response of gold nanostars

    International Nuclear Information System (INIS)

    Kumar, Pandian Senthil; Pastoriza-Santos, Isabel; RodrIguez-Gonzalez, Benito; Abajo, F Javier GarcIa de; Liz-Marzan, Luis M

    2008-01-01

    Multipod Au nanoparticles (nanostars) with single crystalline tips were synthesized in extremely high yield through the reduction of HAuCl 4 in a concentrated solution of poly(vinylpyrrolidone) (PVP) in N,N-dimethylformamide (DMF), in the presence of preformed Au nanoparticle seeds, but with no need for external energy sources. Nanostar dispersions display a well-defined optical response, which was found (through theoretical modeling) to comprise a main mode confined within the tips and a secondary mode confined in the central body. Calculations of the surface enhanced Raman scattering (SERS) response additionally show that this morphology will be relevant for sensing applications

  16. High yield neutron generators using the DD reaction

    Energy Technology Data Exchange (ETDEWEB)

    Vainionpaa, J. H.; Harris, J. L.; Piestrup, M. A.; Gary, C. K.; Williams, D. L.; Apodaca, M. D.; Cremer, J. T. [Adelphi technology, 2003 E. Bayshore Rd. 94061, Redwood City, CA (United States); Ji, Qing; Ludewigt, B. A. [Lawrence Berkeley National Lab, 1 Cyclotron Road, Berkeley, CA 94720 (United States); Jones, G. [G and J Enterprise, 1258 Quary Ln, Suite F, Pleasanton California 94566 (United States)

    2013-04-19

    A product line of high yield neutron generators has been developed at Adelphi technology inc. The generators use the D-D fusion reaction and are driven by an ion beam supplied by a microwave ion source. Yields of up to 5 Multiplication-Sign 10{sup 9} n/s have been achieved, which are comparable to those obtained using the more efficient D-T reaction. The microwave-driven plasma uses the electron cyclotron resonance (ECR) to produce a high plasma density for high current and high atomic ion species. These generators have an actively pumped vacuum system that allows operation at reduced pressure in the target chamber, increasing the overall system reliability. Since no radioactive tritium is used, the generators can be easily serviced, and components can be easily replaced, providing essentially an unlimited lifetime. Fast neutron source size can be adjusted by selecting the aperture and target geometries according to customer specifications. Pulsed and continuous operation has been demonstrated. Minimum pulse lengths of 50 {mu}s have been achieved. Since the generators are easily serviceable, they offer a long lifetime neutron generator for laboratories and commercial systems requiring continuous operation. Several of the generators have been enclosed in radiation shielding/moderator structures designed for customer specifications. These generators have been proven to be useful for prompt gamma neutron activation analysis (PGNAA), neutron activation analysis (NAA) and fast neutron radiography. Thus these generators make excellent fast, epithermal and thermal neutron sources for laboratories and industrial applications that require neutrons with safe operation, small footprint, low cost and small regulatory burden.

  17. combining high seed number and weight to improve seed yield

    African Journals Online (AJOL)

    ACSS

    ABSTRACT. Increasing seed size and seed weight is an important trait for trade, yield component and adaptation of chickpea ... determining yield or quality, and the development of rapid and ..... C.G. 1981. Control of seed growth in soybeans.

  18. High yield silicon carbide pre-ceramic polymers

    International Nuclear Information System (INIS)

    Baney, R.H.

    1982-01-01

    Polysilanes which are substituted with (CH 3 ) 3 SiO-groups are useful for the preparation in high yields of fine grained silicon carbide ceramic materials. They consist of 0 to 60 mole % (CH 3 ) 2 Si units and 100 to 40 mole % CH 3 Si units, all Si valences not satisfied by CH 3 groups or Si atoms being directed to groups (CH 3 ) 3 SiO-, which siloxane groups amount to 23 to 61 weight % of the polysilane. They are prepared by reaction of the corresponding chloro- or bromo-methyl polysilanes with at least the stoichiometric amounts of (CH 3 ) 3 SiOSi(CH 3 ) 3 and water in the presence of a strong acid. (author)

  19. A high throughput DNA extraction method with high yield and quality

    Directory of Open Access Journals (Sweden)

    Xin Zhanguo

    2012-07-01

    Full Text Available Abstract Background Preparation of large quantity and high quality genomic DNA from a large number of plant samples is a major bottleneck for most genetic and genomic analyses, such as, genetic mapping, TILLING (Targeting Induced Local Lesion IN Genome, and next-generation sequencing directly from sheared genomic DNA. A variety of DNA preparation methods and commercial kits are available. However, they are either low throughput, low yield, or costly. Here, we describe a method for high throughput genomic DNA isolation from sorghum [Sorghum bicolor (L. Moench] leaves and dry seeds with high yield, high quality, and affordable cost. Results We developed a high throughput DNA isolation method by combining a high yield CTAB extraction method with an improved cleanup procedure based on MagAttract kit. The method yielded large quantity and high quality DNA from both lyophilized sorghum leaves and dry seeds. The DNA yield was improved by nearly 30 fold with 4 times less consumption of MagAttract beads. The method can also be used in other plant species, including cotton leaves and pine needles. Conclusion A high throughput system for DNA extraction from sorghum leaves and seeds was developed and validated. The main advantages of the method are low cost, high yield, high quality, and high throughput. One person can process two 96-well plates in a working day at a cost of $0.10 per sample of magnetic beads plus other consumables that other methods will also need.

  20. Effect of Planting Density and Harvest Interval on the Leaf Yield and Quality of Moringa (Moringa oleifera under Diverse Agroecological Conditions of Northern South Africa

    Directory of Open Access Journals (Sweden)

    M. P. Mabapa

    2017-01-01

    Full Text Available Smallholder livestock farmers who depend on natural communal grazing lands are particularly vulnerable to climate change as well as to food insecurity and should be encouraged to grow drought-tolerant fodder crops. Moringa oleifera is a highly valued plant, due to its exceptionally high nutritional content. This study was conducted at two experimental sites in the Limpopo province of northern South Africa to evaluate for the first time the effect of plant density and cutting interval on biomass production and chemical composition of moringa grown under two diverse climatic conditions. Four different planting densities (435,000, 300,000, 200,000, and 100,000 plants/ha were arranged in a randomized complete block design and experimental samples were replicated four times. Data for biomass and gravimetric soil moisture content were collected each time the plants reached a height of 50 cm. Harvested leaves were analysed for chemical composition. An increase in the plant density led to elevated biomass production at both study locations, ranging between 527 and 2867 kg/ha. Moringa is capable of meeting all nutrient requirements of livestock depending on harvest time and location.

  1. Simultaneous harvesting of straw and chaff - for energy purposes. Influence on bale density, yield, field drying process and combustion characteristics; Samtidig skoerd av halm och agnar foer energiaendamaal - inverkan paa avkastning, baldensitet, faelttorkningsfoerlopp och foerbraenningsegenskaper

    Energy Technology Data Exchange (ETDEWEB)

    Lundin, Gunnar; Roennbaeck, Marie

    2010-04-15

    Introductory field experiments were carried out in central Sweden during 2009 for long- and short-stalked winter wheat crops. Two different types of combine harvesters were used with somewhat different methods of kernel separation. Both harvesters were equipped with the Combi System from Rekordverken. This enabled them to mix the chaff in the straw swath as well as distribute this fraction over the working width. The measurement of crop residue moisture immediately after combine harvesting showed that admixture of chaff reduced the initial moisture in the straw swaths. The added chaff increased the total yield of crop residue with 14%, showing that about half the biologically available chaff was harvested. The combustion analyses showed a slight increase in ash content when chaff was mixed in. This did not cause any significant change in net calorific value or ash melting behavior

  2. Isolation of hardy and high-yielding mutants in citronella (Cymbopogon winterianus)

    International Nuclear Information System (INIS)

    Kole, C.R.

    1990-01-01

    Full text: Citronella bears an essential oil of medicinal and aromatic importance. But little has been done for its genetic improvement. It is a clonally propagated crop and the genetic variability is too low for effective selection. Besides, various reproductive anomalies limit the scope for cross-breeding. With this in view, a mutation induction experiment was conducted. This crop is mostly grown in marginal lands and hardy genotypes are required. Exposure of vegetative slips of an improved strain (KS-CW-S-I) to x-rays at 3,6 and 9kR paved the way for selection of 53 elite M 1 V 2 clumps on the basis of the yield component characters. Mass screening under minimal cultural practices in a drought-prone zone in Western Orissa (India) led to identification of 16 potentially hardy clones (OJC-12 from 3kR, OJC-1, 3, 11, 18 and 20 from 6kR and OJC-4, 5, 6, 15, 21, 22, 24, 26, 30 and 31 from 9kR). The clones were planted with 3 replications in mid-monsoon, established during the remaining months of monsoon and grown thereafter under minimal cultural practices, i.e. no manure, fertiliser, irrigation, weeding or plant protection. Data on yield of fresh leaf and oil extracted from fresh leaves were recorded at harvest 6 months after planting at 5 to 6 leaf stage. The results revealed a highly significant variation with regard to yield of both leaf and oil. Six clones out-yielded the mother line for leaf as well as oil, and two clones surpassed the mother line in leaf yield only. The performance of clone OJC-3 was particularly encouraging. With 1.25 kg/plant leaf, 9.63cc/plant oil it superseded the yield of the mother line and other cultivars of this species (all around 0.6 kg/plant leaf, 5cc/plant oil) even when grown with irrigation. (author)

  3. High yield CTMP fibres as a possibility of the more efficient yield of wood raw material

    Directory of Open Access Journals (Sweden)

    Klašnja Bojana A.

    2004-01-01

    Full Text Available The evident shortage of wood as a raw material has become a limiting factor in the pulp and paper industry which is the greatest consumer of wood in Europe. The situation in our country is similar. During the few past years, the production of poplar and willow pulpwood was 220.000 m3 per year, which is insufficient for the planned increase in the production of sulphate pulp (175.000 tons till 2005. This paper deals with the aspects of the more efficient yield of raw material, based on the significantly higher yield of CTMP fibres, as well as with the significance of the lower adverse effect on the environment. It also analyses the conditions of production and the quality of the obtained fibres, as a possible substitute for chemical pulp and secondary fibres in papers of different quality. The main reasons for the production and use of CTMP fibres in our country are reported.

  4. Nutrient Uptake by High-Yielding Cotton Crop in Brazil

    Directory of Open Access Journals (Sweden)

    José Luís Vilela Vieira

    2018-02-01

    Full Text Available ABSTRACT: Determining nutrient uptake and accumulation rates by cotton crops is important to define management strategies, especially for transgenic varieties, which are cultivated using high-technology approaches that require substantial investment to maximize yield. Currently in Brazil, the states of Bahia and Mato Grosso are responsible for 84.4 % of the total cotton growing area. In the present study, two trials were conducted in 2013, one that involved planting FM 940 GLT, FM 980 GLT, and FM 913 GLT varieties in the state of Bahia and the other which involved FM 940 GLT and FM 980 GLT varieties in the state of Mato Grosso. The aim of the two trials was to represent the two regions that currently encompass the largest areas of cotton cultivation. Tissue samples, consisting of leaves, stems, and reproductive components, were collected eleven times during the crop cycle for determination of nutrient content and shoot dry matter. After weighing, plant tissue samples were dried and ground to determine nutrient contents. Because there were no overall differences in nutrient contents and biomass accumulation of the varieties during the crop cycle, we undertook joint analysis of the data from all varieties at each site. Favorable climatic conditions in Bahia promoted plant biomass production that was twice as much as plants grown in Mato Grosso, with cotton yields of 6.2 and 3.8 t ha−1 of lint and seed, respectively. The maximum nutrient accumulation occurred between 137-150 days after emergence (DAE for N; 143-148 for P; 172-185 for K; 100 for Ca; 144-149 for Mg; and 153-158 for S. Maximum uptake ranged from 218-362 kg ha−1 N; 26-53 kg ha−1 P; 233-506 kg ha−1 K; 91-202 kg ha−1 Ca; 28-44 kg ha−1 Mg; and 19-61 kg ha−1 S. On average, the sites revealed nutrient export of 14, 2, 23, 3, 2, and 2 kg t−1 of lint and seed for N, P, K, Ca, Mg, and S, respectively, with little variation among sites. Extraction of nutrients per area by cotton

  5. A High-Efficiency Wind Energy Harvester for Autonomous Embedded Systems.

    Science.gov (United States)

    Brunelli, Davide

    2016-03-04

    Energy harvesting is currently a hot research topic, mainly as a consequence of the increasing attractiveness of computing and sensing solutions based on small, low-power distributed embedded systems. Harvesting may enable systems to operate in a deploy-and-forget mode, particularly when power grid is absent and the use of rechargeable batteries is unattractive due to their limited lifetime and maintenance requirements. This paper focuses on wind flow as an energy source feasible to meet the energy needs of a small autonomous embedded system. In particular the contribution is on the electrical converter and system integration. We characterize the micro-wind turbine, we define a detailed model of its behaviour, and then we focused on a highly efficient circuit to convert wind energy into electrical energy. The optimized design features an overall volume smaller than 64 cm³. The core of the harvester is a high efficiency buck-boost converter which performs an optimal power point tracking. Experimental results show that the wind generator boosts efficiency over a wide range of operating conditions.

  6. A High-Efficiency Wind Energy Harvester for Autonomous Embedded Systems

    Science.gov (United States)

    Brunelli, Davide

    2016-01-01

    Energy harvesting is currently a hot research topic, mainly as a consequence of the increasing attractiveness of computing and sensing solutions based on small, low-power distributed embedded systems. Harvesting may enable systems to operate in a deploy-and-forget mode, particularly when power grid is absent and the use of rechargeable batteries is unattractive due to their limited lifetime and maintenance requirements. This paper focuses on wind flow as an energy source feasible to meet the energy needs of a small autonomous embedded system. In particular the contribution is on the electrical converter and system integration. We characterize the micro-wind turbine, we define a detailed model of its behaviour, and then we focused on a highly efficient circuit to convert wind energy into electrical energy. The optimized design features an overall volume smaller than 64 cm3. The core of the harvester is a high efficiency buck-boost converter which performs an optimal power point tracking. Experimental results show that the wind generator boosts efficiency over a wide range of operating conditions. PMID:26959018

  7. A High-Efficiency Wind Energy Harvester for Autonomous Embedded Systems

    Directory of Open Access Journals (Sweden)

    Davide Brunelli

    2016-03-01

    Full Text Available Energy harvesting is currently a hot research topic, mainly as a consequence of the increasing attractiveness of computing and sensing solutions based on small, low-power distributed embedded systems. Harvesting may enable systems to operate in a deploy-and-forget mode, particularly when power grid is absent and the use of rechargeable batteries is unattractive due to their limited lifetime and maintenance requirements. This paper focuses on wind flow as an energy source feasible to meet the energy needs of a small autonomous embedded system. In particular the contribution is on the electrical converter and system integration. We characterize the micro-wind turbine, we define a detailed model of its behaviour, and then we focused on a highly efficient circuit to convert wind energy into electrical energy. The optimized design features an overall volume smaller than 64 cm3. The core of the harvester is a high efficiency buck-boost converter which performs an optimal power point tracking. Experimental results show that the wind generator boosts efficiency over a wide range of operating conditions.

  8. High Yield F-18 Target for KOTRON-13 Cyclotron

    International Nuclear Information System (INIS)

    Lee, W. K.; Song, J. Y.; Park, J. Y.; Jung, K. I.; Chae, S. K.

    2009-01-01

    Currently the domestic radiation market for medical diagnosis witnesses a high increase of the use of PET/CT for the purpose of cancer diagnosis, and the cases of cancer diagnosis using PET/CT increase by geometric progression every year. In case of domestic practice, full body scan is taken by using FDG medical isotope medicines mainly using F-18, but the necessity of various medical radioactive isotopes according to each medical purpose is increasing. F-18 output yield is directly proportional to energy of protons and beam current, and has correlation with heat production rate in case of target and decides the function of target in accordance with the efficiency of a cooling device. At present, in case of most F-18 target, when one irradiates beam in O-18 water of about 0.2∼5mL, one has to apply heat of over 300W, a high thermal energy per unit area is irradiated in target, which is easily damaged, and it has limitation in beam current. Currently, in case of commercial target, about 2,000W beam current is the maximum value, and in case of double-grid target developed by Korea Institute of Radiological and Medical Sciences in 2004, it was designed to stand up to about 1,000W theoretically, but in reality it can irradiate lower beam current than this because of the shortage of cooling efficiency. In general, the irradiation strength to produce radioactive isotopes given in the heat emission by target substance currently is limited to 50μA against target substance irradiated in 1.6mL. However, current KOTRON-13 cyclotron can accelerate proton beam with a high scope of strength marking 100μA thru 120μA by a continuous development. Therefore, it doesn't fully function compared with that of proton beam of KOTRON-13 cyclotron. The solution about this is to get over the problem of cooling target substance of cavity in the production system of radioactive isotopes. Especially, one has to develop the method to cool target substance, and provide higher F-18 yield than

  9. Diagnostics of Shiva Nova produced high yield thermonuclear events

    International Nuclear Information System (INIS)

    Ahlstrom, H.G.; Banner, D.L.; Boyle, M.J.; Campbell, E.M.; Coleman, L.W.; Koppel, L.N.; Kornblum, H.N. Jr.; Rienecker, F.; Severyn, J.R.; Slivinsky, V.W.

    1978-01-01

    Experiments with the Shiva Nova laser facility which produce yield levels of scientific breakeven and above will result in neutron, x-ray and particle fluxes which will require specific attention to the survivability of diagnostic instrumentation. These yield levels will also allow the utilization of new diagnotics techniques which can provide detailed information on the state of the imploded fuel and pusher shells

  10. Highly efficient integrated rectifier and voltage boosting circuits for energy harvesting applications

    Directory of Open Access Journals (Sweden)

    D. Maurath

    2008-05-01

    Full Text Available This paper presents novel circuit concepts for integrated rectifiers and voltage converting interfaces for energy harvesting micro-generators. In the context of energy harvesting, usually only small voltages are supplied by vibration-driven generators. Therefore, rectification with minimum voltage losses and low reverse currents is an important issue. This is realized by novel integrated rectifiers which were fabricated and are presented in this article. Additionally, there is a crucial need for dynamic load adaptation as well as voltage up-conversion. A circuit concept is presented, which is able to obtain both requirements. This generator interface adapts its input impedance for an optimal energy transfer efficiency. Furthermore, this generator interface provides implicit voltage up-conversion, whereas the generator output energy is stored on a buffer, which is connected to the output of the voltage converting interface. As simulations express, this fully integrated converter is able to boost ac-voltages greater than |0.35 V| to an output dc-voltage of 2.0 V–2.5 V. Thereby, high harvesting efficiencies above 80% are possible within the entire operational range.

  11. Nutritional status of high yielding crossbred cow around parturition

    Directory of Open Access Journals (Sweden)

    Mohammad Yousuf

    2016-03-01

    Materials and methods: Nutritional status of cows around the peri-parturient period was investigated for six months in dairy farm. Seven to eight months' pregnant cows were selected for this study. Blood samples from 24 randomly selected cows were collected at stage-1, -2 and -3. The serum was stored at -20C until analyzing glucose, total protein (TP, albumin (Alb, triglycerides (Tg, cholesterol, high density lipoprotein (HDL, low density lipoprotein (LDL, calcium (Ca, magnesium (Mg and phosphorus (P. Results: An increasing trend of glucose level was evidenced (P=0.07 during stage-1. Instead, higher levels of TP were found during stage-3 as compared to the stage-1 and -2. The Alb levels differed significantly (P<0.01 among different stages. A significantly increased (P<0.01 cholesterol, Tg, and HDL were found after parturition (stage-2 and -3 than before parturition (stage-1. LDL was significantly (P=0.02 increased during stage-2 and -3. A significantly higher level of Ca (P<0.01, Mg (P<0.01 and P (P=0.03 were present during stage-1. Glucose, TP, cholesterol and Tg were significantly higher (P<0.01 in cows two months after parturition, while Alb was found to be the highest (P<0.01 in cows immediately after parturition. An increasing trend of LDL (P=0.07 and HDL (P=0.07 were found in the cows two months after parturition. However, Ca levels were significantly (P=0.04 higher in cows two months after parturition. Conclusion: The results indicate that there is alteration of biochemical levels among the study population at three different stages, and these data may be helpful in using the necessary nutrients to the the high yielding cows around their parturition. [J Adv Vet Anim Res 2016; 3(1.000: 68-74

  12. The Radioactive Waste Management course: 14 High-yield editions

    International Nuclear Information System (INIS)

    Alonso, A.; Gallego, E.; Marco, M. L.; Falcon, S.

    2003-01-01

    The doctorate course on Radioactive Waste Management was initiated in February 1988, by initiative of the Chair of Nuclear Technology, under the sponsoring of the national radioactive waste management company (ENRESA), in a fruitful collaboration between the Institute Artigas of the Technical School of Industrial Engineering and the Institute of Formation on Energy of the research centre CIEMAT. The course is also offered as a post-graduate through both institutes. After completion of fourteen consecutive editions in 2002, the course constituted a landmark in the field of nuclear education in Spain. The last edition offered, along 35 lessons published in two books, the general aspects of generation, treatment and conditioning of radioactive wastes, the basic Safety and Radiological Protection criteria, the detailed technical questions of the management of both low-intermediate.activity and the high-activity level, together with the wastes generated during decommissioning and dismantling of installations, as well as the general and institutional aspects. Experts in each field, belonging either to ENRESA, CIEMAT, the Nuclear Safety Council, the UPM and the industry, present such wide programme. A technical visit to the low and intermediate radioactive waste repository of El Cabril was also offered to the participants as part of the course, as in previous years the visit to the dismantling workers of Vandellos I NPP. More than 500 engineers and graduates in different science branches have participated in the course along 14 years, with both students and professionals belonging to ENRESA, the Nuclear Safety Council, CIEMAT and other research centers, hospitals, civil protection at different levels, service and engineering companies related with the radioactive waste management. Altogether, it is possible to say, as the title is expressed, that the course has given in these 14 years a high-production yield. (Author)

  13. Induction of resistance to blast disease (Pyricularia oryzae) in the high yielding variety, Ratna (IR8xTKM6)

    International Nuclear Information System (INIS)

    Kaur, S.; Padmanabhan, S.Y.; Kaur, P.

    1977-01-01

    The high yielding variety, Ratna (IR8 x TKM6), susceptible to blast disease (Pyricularia oryzae Cav.), was taken up for induction of resistance to the disease through EMS treatment. The seeds of individual M 1 plants were harvested and grown as M 2 generation in a ''uniform blast nursery''. The scoring and classification of blast reaction was done according to the method described by Padmanabhan and Ganguly. The seeds of ''resistant'' selections and ''susceptible'' selections were harvested, grown and tested again in the ''uniform blast nursery'' for M 3 , M 4 and M 5 generations. Ratna (untreated) developed 'B', 'C', and 'D' type of spots whereas the EMS-treated populations in all generations, i.e. M 2 -M 4 , developed 'O', 'A' and 'E' types of spot, in addition to 'B', 'C' and 'D' types, in both resistant and susceptible selections. This indicated that the chemical mutagen EMS induced variability in both negative and positive directions. In M 5 generation, 50 out of 1500 originally selected lines were found to be breeding true for disease resistance. Some mutants retain the grain characters of Ratna, and the high yield. The mutagen treatment also induced variability in grain characters. Ratna has a long slender grain. Some mutants have medium slender, short bold or long bold grain. (author)

  14. High yield Cu-Co CPP GMR multilayer sensors

    International Nuclear Information System (INIS)

    Spallas, J., Mao, M., Law, B., Grabner, F., Cerjan, C., O'Kane, O.

    1997-01-01

    We have fabricated and tested GMR magnetic flux sensors that operate in the CPP mode. This work is a continuation of the ultra-high density magnetic sensor research introduced at INTERMAG 96. We have made two significant modifications to the process sequence. First, contact to the sensor is made through a metal conduit deposited in situ with the multilayers. This deposition replaces electroplating. This configuration ensures a good electrical interface between the top of multilayer stack and the top contact, and a continuous, conductive current path to the sensor. The consequences of this modification are an increase in yield of operational devices to ≥90% per wafer and a significant reduction of the device resistance to ≤560 milliohms and of the uniformity of the device resistance to ≤3%. Second, the as-deposited multilayer structure has been changed from [Cu 30 angstrom/Co 20 angstrom] 18 (third peak) to [Cu 20.5 angstrom/Co 12 angstrom] 30 (second peak) to increase the CPP and CIP responses. The sheet film second peak CIP GMR response is 18% and the sensitivity is 0.08 %/Oe. The sheet film third peak CIP GMR response is 8% and the sensitivity is 0. 05 %/Oe. The second peak CPP GMR response averaged over twenty devices on a four inch silicon substrate is 28% ± 6%. The response decreases radially from the substrate center. The average response at the center of the substrate is 33% ± 4%. The average second peak CPP sensitivity is 0.09 %/Oe ± 0.02 %/Oe. The best second peak CPP response from a single device is 39%. The sensitivity of that device is 0.13 %/Oe. The third peak CPP GMR response is approximately 14 %. The third peak CPP response sensitivity is 0.07 %/Oe. 6 refs., 3 figs

  15. Lichen Symbiosis: Nature's High Yielding Machines for Induced Hydrogen Production

    Science.gov (United States)

    Papazi, Aikaterini; Kastanaki, Elizabeth; Pirintsos, Stergios; Kotzabasis, Kiriakos

    2015-01-01

    Hydrogen is a promising future energy source. Although the ability of green algae to produce hydrogen has long been recognized (since 1939) and several biotechnological applications have been attempted, the greatest obstacle, being the O2-sensitivity of the hydrogenase enzyme, has not yet been overcome. In the present contribution, 75 years after the first report on algal hydrogen production, taking advantage of a natural mechanism of oxygen balance, we demonstrate high hydrogen yields by lichens. Lichens have been selected as the ideal organisms in nature for hydrogen production, since they consist of a mycobiont and a photobiont in symbiosis. It has been hypothesized that the mycobiont’s and photobiont’s consumption of oxygen (increase of COX and AOX proteins of mitochondrial respiratory pathways and PTOX protein of chrolorespiration) establishes the required anoxic conditions for the activation of the phycobiont’s hydrogenase in a closed system. Our results clearly supported the above hypothesis, showing that lichens have the ability to activate appropriate bioenergetic pathways depending on the specific incubation conditions. Under light conditions, they successfully use the PSII-dependent and the PSII-independent pathways (decrease of D1 protein and parallel increase of PSaA protein) to transfer electrons to hydrogenase, while under dark conditions, lichens use the PFOR enzyme and the dark fermentative pathway to supply electrons to hydrogenase. These advantages of lichen symbiosis in combination with their ability to survive in extreme environments (while in a dry state) constitute them as unique and valuable hydrogen producing natural factories and pave the way for future biotechnological applications. PMID:25826211

  16. Lichen symbiosis: nature's high yielding machines for induced hydrogen production.

    Directory of Open Access Journals (Sweden)

    Aikaterini Papazi

    Full Text Available Hydrogen is a promising future energy source. Although the ability of green algae to produce hydrogen has long been recognized (since 1939 and several biotechnological applications have been attempted, the greatest obstacle, being the O2-sensitivity of the hydrogenase enzyme, has not yet been overcome. In the present contribution, 75 years after the first report on algal hydrogen production, taking advantage of a natural mechanism of oxygen balance, we demonstrate high hydrogen yields by lichens. Lichens have been selected as the ideal organisms in nature for hydrogen production, since they consist of a mycobiont and a photobiont in symbiosis. It has been hypothesized that the mycobiont's and photobiont's consumption of oxygen (increase of COX and AOX proteins of mitochondrial respiratory pathways and PTOX protein of chrolorespiration establishes the required anoxic conditions for the activation of the phycobiont's hydrogenase in a closed system. Our results clearly supported the above hypothesis, showing that lichens have the ability to activate appropriate bioenergetic pathways depending on the specific incubation conditions. Under light conditions, they successfully use the PSII-dependent and the PSII-independent pathways (decrease of D1 protein and parallel increase of PSaA protein to transfer electrons to hydrogenase, while under dark conditions, lichens use the PFOR enzyme and the dark fermentative pathway to supply electrons to hydrogenase. These advantages of lichen symbiosis in combination with their ability to survive in extreme environments (while in a dry state constitute them as unique and valuable hydrogen producing natural factories and pave the way for future biotechnological applications.

  17. A shell-neutral modeling approach yields sustainable oyster harvest estimates: a retrospective analysis of the Louisiana state primary seed grounds

    Science.gov (United States)

    Soniat, Thomas M.; Klinck, John M.; Powell, Eric N.; Cooper, Nathan; Abdelguerfi, Mahdi; Hofmann, Eileen E.; Dahal, Janak; Tu, Shengru; Finigan, John; Eberline, Benjamin S.; La Peyre, Jerome F.; LaPeyre, Megan K.; Qaddoura, Fareed

    2012-01-01

    A numerical model is presented that defines a sustainability criterion as no net loss of shell, and calculates a sustainable harvest of seed (<75 mm) and sack or market oysters (≥75 mm). Stock assessments of the Primary State Seed Grounds conducted east of the Mississippi from 2009 to 2011 show a general trend toward decreasing abundance of sack and seed oysters. Retrospective simulations provide estimates of annual sustainable harvests. Comparisons of simulated sustainable harvests with actual harvests show a trend toward unsustainable harvests toward the end of the time series. Stock assessments combined with shell-neutral models can be used to estimate sustainable harvest and manage cultch through shell planting when actual harvest exceeds sustainable harvest. For exclusive restoration efforts (no fishing allowed), the model provides a metric for restoration success-namely, shell accretion. Oyster fisheries that remove shell versus reef restorations that promote shell accretion, although divergent in their goals, are convergent in their management; both require vigilant attention to shell budgets.

  18. Selection of common bean lines with high grain yield and high grain calcium and iron concentrations

    Directory of Open Access Journals (Sweden)

    Nerinéia Dalfollo Ribeiro

    2014-02-01

    Full Text Available Genetic improvement of common bean nutritional quality has advantages in marketing and can contribute to society as a food source. The objective of this study was to evaluate the genetic variability for grain yield, calcium and iron concentrations in grains of inbred common bean lines obtained by different breeding methods. For this, 136 F7 inbred lines were obtained using the Pedigree method and 136 F7 inbred lines were obtained using the Single-Seed Descent (SSD method. The lines showed genetic variability for grain yield, and concentrations of calcium and iron independently of the method of advancing segregating populations. The Pedigree method allows obtaining a greater number of lines with high grain yield. Selection using the SSD method allows the identification of a larger number of lines with high concentrations of calcium and iron in grains. Weak negative correlations were found between grain yield and calcium concentration (r = -0.0994 and grain yield and iron concentration (r = -0.3926. Several lines show genetic superiority for grain yield and concentrations of calcium and iron in grains and their selection can result in new common bean cultivars with high nutritional quality.

  19. Highly Adaptive Solid-Liquid Interfacing Triboelectric Nanogenerator for Harvesting Diverse Water Wave Energy.

    Science.gov (United States)

    Zhao, Xue Jiao; Kuang, Shuang Yang; Wang, Zhong Lin; Zhu, Guang

    2018-05-22

    Harvesting water wave energy presents a significantly practical route to energy supply for self-powered wireless sensing networks. Here we report a networked integrated triboelectric nanogenerator (NI-TENG) as a highly adaptive means of harvesting energy from interfacing interactions with various types of water waves. Having an arrayed networking structure, the NI-TENG can accommodate diverse water wave motions and generate stable electric output regardless of how random the water wave is. Nanoscaled surface morphology consisting of dense nanowire arrays is the key for obtaining high electric output. A NI-TENG having an area of 100 × 70 mm 2 can produce a stable short-circuit current of 13.5 μA and corresponding electric power of 1.03 mW at a water wave height of 12 cm. This merit promises practical applications of the NI-TENG in real circumstances, where water waves are highly variable and unpredictable. After energy storage, the generated electric energy can drive wireless sensing by autonomously transmitting data at a period less than 1 min. This work proposes a viable solution for powering individual standalone nodes in a wireless sensor network. Potential applications include but are not limited to long-term environment monitoring, marine surveillance, and off-shore navigation.

  20. [Dynamic changes of soil microbial populations and enzyme activities in super-high yielding summer maize farmland soil].

    Science.gov (United States)

    Hou, Peng; Wang, Yong-jun; Wang, Kong-jun; Yang, Jin-sheng; Li, Deng-hai; Dong, Shu-ting; Liu, Jing-guo

    2008-08-01

    To reveal the characteristics of the dynamic changes of soil microbial populations and enzyme activities in super-high yielding ( > 15,000 kg x hm(-2)) summer maize farmland soil, a comparative study was conducted in the experimental fields in National Maize Engineering Research Center (Shandong). On the fields with an annual yield of >15,000 kg x hm(-2) in continuous three years, a plot with the yield of 20 322 kg x hm(-2) (HF) was chosen to make comparison with the conventional farmland (CF) whose maize yield was 8920. 1 kg x hm(-2). The numbers of bacteria, fungi, and actinomycetes as well as the activities of urease and invertase in 0-20 cm soil layer were determined. The results showed that in the growth period of maize, the numbers of bacteria, fungi, and actinomycetes in the two farmland soils increased first and declined then. At the later growth stages of maize, the numbers of soil microbes, especially those of bacteria and actinomycetes, were lower in HF than those in CF. At harvest stage, the ratio of the number of soil bacteria to fungi (B/ F) in HF was 2.03 times higher than that at sowing stage, and 3.02 times higher than that in CF. The B/F in CF had less difference at harvest and sowing stages. The soil urease activity in HF was significantly lower than that in CF at jointing stage, and the invertase activity in HF decreased rapidly after blooming stage, being significantly lower than that in CF.

  1. Induction of high yielding and high protein containing chickpea mutant variety through gamma radiation

    International Nuclear Information System (INIS)

    Hassan, S.; Javed, M.A.; Khan, A.J.; Tariq, M.

    1997-01-01

    Pure seeds of a blight susceptible but high yielding chickpea variety 6153 were irradiated at 20 Kr(0.2 kGy) dose of gamma radiation and the mutant line CMN-446-4 was selected in M3 generation on the basis of high yield and disease resistance. After confirmation of its resistance to blight in M4 and M5, the mutant line CMN-446-4 along with other promising chickpea mutants were evaluated in various yield trials at different locations. The mutant line CMN-446-4 was got evaluated in chickpea national uniform yield trial conducted over two locations in the country during 1993-94. The mutant line, on average, ranked 3rd by producing significantly higher yield of 1528 kg/ha as compared to the two checked varieties Punjab-91 and Paidar-91 which yielded 1316 and 1391 kg/ha respectively. The mutant CMN-446-4 has significantly greater percentage of protein content (25.22%) compared to its parental variety having (20.12%). (author)

  2. Evaluation of high yielding soybean germplasm under water limitation.

    Science.gov (United States)

    Prince, Silvas J; Murphy, Mackensie; Mutava, Raymond N; Zhang, Zhengzhi; Nguyen, Na; Kim, Yoon Ha; Pathan, Safiullah M; Shannon, Grover J; Valliyodan, Babu; Nguyen, Henry T

    2016-05-01

    Limited information is available for soybean root traits and their plasticity under drought stress. To date, no studies have focused on examining diverse soybean germplasm for regulation of shoot and root response under water limited conditions across varying soil types. In this study, 17 genetically diverse soybean germplasm lines were selected to study root response to water limited conditions in clay (trial 1) and sandy soil (trial 2) in two target environments. Physiological data on shoot traits was measured at multiple crop stages ranging from early vegetative to pod filling. The phenotypic root traits, and biomass accumulation data are collected at pod filling stage. In trial 1, the number of lateral roots and forks were positively correlated with plot yield under water limitation and in trial 2, lateral root thickness was positively correlated with the hill plot yield. Plant Introduction (PI) 578477A and 088444 were found to have higher later root number and forks in clay soil with higher yield under water limitation. In sandy soil, PI458020 was found to have a thicker lateral root system and higher yield under water limitation. The genotypes identified in this study could be used to enhance drought tolerance of elite soybean cultivars through improved root traits specific to target environments. © 2015 Institute of Botany, Chinese Academy of Sciences.

  3. High positive computed tomography yields in the emergency ...

    African Journals Online (AJOL)

    when the diagnosis is uncertain.[1,2] It is therefore ... Methods. This was a retrospective record review of all patients who received CT ... period. Primary outcomes were to establish CT scan usage and positive yield rates. ... scans performed in the hospital. ... considered for surgical intervention may have a negative scan and.

  4. High-resolution mapping of yield curve shape and evolution for high porosity sandstones

    Science.gov (United States)

    Bedford, J. D.; Faulkner, D.; Wheeler, J.; Leclere, H.

    2017-12-01

    The onset of permanent inelastic deformation for porous rock is typically defined by a yield curve plotted in P-Q space, where P is the effective mean stress and Q is the differential stress. Sandstones usually have broadly elliptical shaped yield curves, with the low pressure side of the ellipse associated with localized brittle faulting (dilation) and the high pressure side with distributed ductile deformation (compaction). However recent works have shown that these curves might not be perfectly elliptical and that significant evolution in shape occurs with continued deformation. We therefore use a novel stress-probing methodology to map in high-resolution the yield curve shape for Boise and Idaho Gray sandstones (36-38% porosity) and also investigate curve evolution with increasing deformation. The data reveal yield curves with a much flatter geometry than previously recorded for porous sandstone and that the compactive side of the curve is partly comprised of a near vertical limb. The yield curve evolution is found to be strongly dependent on the nature of inelastic strain. Samples that were compacted under a deviatoric load, with a component of inelastic shear strain, were found to have yield curves with peaks that are approximately 50% higher than similar porosity samples that were hydrostatically compacted (i.e. purely volumetric strain). The difference in yield curve evolution along the different loading paths is attributed to mechanical anisotropy that develops during deviatoric loading by the closure of preferentially orientated fractures. Increased shear strain also leads to the formation of a plateau at the peak of the yield curve as samples deform along the deviatoric loading path. These results have important implications for understanding how the strength of porous rock evolves along different stress paths, including during fluid extraction from hydrocarbon reservoirs where the stress state is rarely isotropic.

  5. High yielding small grain mutant of rice variety Pankaj

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1987-07-01

    Full text: By treatment with EMS a mutant has been produced from the variety Pankaj which has better tillering, longer panicle and more grains per panicle. In multilocation trials at Burdwan, Suri and Rampurhat in West Bengal it yielded significantly more than Pankaj and Mahsuri at all locations, with a mean 5.2t. The mutant named BU 79 would be a suitable substitute for Pankaj and similar long-duration rices. (author)

  6. Breeding high yielding varieties of pigeon pea, mungbean and black gram using induced mutations

    International Nuclear Information System (INIS)

    Pawar, S.E.; Wanjari, K.B.

    1994-01-01

    The present communication emphasis the developing of high yielding varieties of pigeon pea, mungbean and black gram using induced mutation with disease resistance in these crops. This would help in stabilisation of the higher yield potential

  7. Non-enhanced phytoextraction of cadmium, zinc, and lead by high-yielding crops.

    Science.gov (United States)

    Mayerová, Markéta; Petrová, Šárka; Madaras, Mikuláš; Lipavský, Jan; Šimon, Tomáš; Vaněk, Tomáš

    2017-06-01

    Heavy metal soil contamination from mining and smelting has been reported in several regions around the world, and phytoextraction, using plants to accumulate risk elements in aboveground harvestable organs, is a useful method of substantially reducing this contamination. In our 3-year experiment, we tested the hypothesis that phytoextraction can be successful in local soil conditions without external fertilizer input. The phytoextraction efficiency of 15 high-yielding crop species was assessed in a field experiment performed at the Litavka River alluvium in the Příbram region of Czechia. This area is heavily polluted by Cd, Zn, and Pb from smelter installations which also polluted the river water and flood sediments. Heavy metal concentrations were analyzed in the herbaceous plants' aboveground and belowground biomass and in woody plants' leaves and branches. The highest Cd and Zn mean concentrations in the aboveground biomass were recorded in Salix x fragilis L. (10.14 and 343 mg kg -1 in twigs and 16.74 and 1188 mg kg -1 in leaves, respectively). The heavy metal content in woody plants was significantly higher in leaves than in twigs. In addition, Malva verticillata L. had the highest Cd, Pb, and Zn concentrations in herbaceous species (6.26, 12.44, and 207 mg kg -1 , respectively). The calculated heavy metal removal capacities in this study proved high phytoextraction efficiency in woody species; especially for Salix × fragilis L. In other tested plants, Sorghum bicolor L., Helianthus tuberosus L., Miscanthus sinensis Andersson, and Phalaris arundinacea L. species are also recommended for phytoextraction.

  8. Yield strength of molybdenum, tantalum and tungsten at high strain rates and very high temperatures

    International Nuclear Information System (INIS)

    Škoro, G.P.; Bennett, J.R.J.; Edgecock, T.R.; Booth, C.N.

    2012-01-01

    Highlights: ► New experimental data on the yield strength of molybdenum, tantalum and tungsten. ► High strain rate effects at record high temperatures (up to 2700 K). ► Test of the consistency of the Zerilli–Armstrong model at very high temperatures. - Abstract: Recently reported results of the high strain rate, high temperature measurements of the yield strength of tantalum and tungsten have been analyzed along with new experimental results on the yield strength of molybdenum. Thin wires are subjected to high stress by passing a short, fast, high current pulse through a thin wire; the amplitude of the current governs the stress and the repetition rate of the pulses determines the temperature of the wire. The highest temperatures reached in the experiments were 2100 °C (for molybdenum), 2250 °C (for tantalum) and 2450 °C (for tungsten). The strain-rates in the tests were in the range from 500 to 1500 s −1 . The parameters for the constitutive equation developed by Zerilli and Armstrong have been determined from the experimental data and the results have been compared with the data obtained at lower temperatures. An exceptionally good fit is obtained for the deformation of tungsten.

  9. Breeding high yielding, high protein spring wheats: Problems, progress and approaches to further advances

    International Nuclear Information System (INIS)

    Konzak, C.F.; Rubenthaler, G.L.

    1984-01-01

    Preliminary data offer promise that advances have been made in breeding hard red spring wheat selections with a yielding capacity about equal to current cultivars and with an increased capacity for producing high protein grain. The most promising new selections are derivatives of Magnif 41M1, CI17689, a semi-dwarf mutant of an Argentinian high protein cultivar. Rapid changes in disease and pest problems also required immediate attention and a reorientation of breeding materials and goals. Selection procedures suggested as promising include early generation (F 2 and F 3 ) screening for disease resistance and agronomic type, with screening for protein content delayed until F 4 or F 5 . Cultural conditions conducive for expressing the highest yield capacity are proposed as optimum for identifying those selections also able to produce high protein grain. A goal of routine production of 14.5% (or higher) protein grain is considered necessary and achievable under fertility management conditions required for maximum yield expression of agronomically competitive cultivars. Agronomically improved sources of high protein genes, an increasing number of induced high protein mutants, and numerous high protein crossbred derivatives of T. dicoccoides and Aegilops species have recently become available. These new or improved germplasm sources as well as a considerable reserve of yet untapped germplasm variability in other accessions of wild T. dicoccoides offer increased optimism that further, rapid advances in the breeding of adapted high yielding, high protein wheats are achievable. Improved breeding schemes, using induced male sterility mutants either to aid in crossing or to develop male sterile facilitated recurrent selection (MSFRS) populations, should contribute towards an earlier achievement of the desired goal while providing the basis for buffering against rapid changes in disease and pest problems

  10. High-power density miniscale power generation and energy harvesting systems

    Energy Technology Data Exchange (ETDEWEB)

    Lyshevski, Sergey Edward [Department of Electrical and Microelectronics Engineering, Rochester Institute of Technology, Rochester, NY 14623-5603 (United States)

    2011-01-15

    This paper reports design, analysis, evaluations and characterization of miniscale self-sustained power generation systems. Our ultimate objective is to guarantee highly-efficient mechanical-to-electrical energy conversion, ensure premier wind- or hydro-energy harvesting capabilities, enable electric machinery and power electronics solutions, stabilize output voltage, etc. By performing the advanced scalable power generation system design, we enable miniscale energy sources and energy harvesting technologies. The proposed systems integrate: (1) turbine which rotates a radial- or axial-topology permanent-magnet synchronous generator at variable angular velocity depending on flow rate, speed and load, and, (2) power electronic module with controllable rectifier, soft-switching converter and energy storage stages. These scalable energy systems can be utilized as miniscale auxiliary and self-sustained power units in various applications, such as, aerospace, automotive, biotechnology, biomedical, and marine. The proposed systems uniquely suit various submersible and harsh environment applications. Due to operation in dynamic rapidly-changing envelopes (variable speed, load changes, etc.), sound solutions are researched, proposed and verified. We focus on enabling system organizations utilizing advanced developments for various components, such as generators, converters, and energy storage. Basic, applied and experimental findings are reported. The prototypes of integrated power generation systems were tested, characterized and evaluated. It is documented that high-power density, high efficiency, robustness and other enabling capabilities are achieved. The results and solutions are scalable from micro ({proportional_to}100 {mu}W) to medium ({proportional_to}100 kW) and heavy-duty (sub-megawatt) auxiliary and power systems. (author)

  11. High-power density miniscale power generation and energy harvesting systems

    International Nuclear Information System (INIS)

    Lyshevski, Sergey Edward

    2011-01-01

    This paper reports design, analysis, evaluations and characterization of miniscale self-sustained power generation systems. Our ultimate objective is to guarantee highly-efficient mechanical-to-electrical energy conversion, ensure premier wind- or hydro-energy harvesting capabilities, enable electric machinery and power electronics solutions, stabilize output voltage, etc. By performing the advanced scalable power generation system design, we enable miniscale energy sources and energy harvesting technologies. The proposed systems integrate: (1) turbine which rotates a radial- or axial-topology permanent-magnet synchronous generator at variable angular velocity depending on flow rate, speed and load, and, (2) power electronic module with controllable rectifier, soft-switching converter and energy storage stages. These scalable energy systems can be utilized as miniscale auxiliary and self-sustained power units in various applications, such as, aerospace, automotive, biotechnology, biomedical, and marine. The proposed systems uniquely suit various submersible and harsh environment applications. Due to operation in dynamic rapidly-changing envelopes (variable speed, load changes, etc.), sound solutions are researched, proposed and verified. We focus on enabling system organizations utilizing advanced developments for various components, such as generators, converters, and energy storage. Basic, applied and experimental findings are reported. The prototypes of integrated power generation systems were tested, characterized and evaluated. It is documented that high-power density, high efficiency, robustness and other enabling capabilities are achieved. The results and solutions are scalable from micro (∼100 μW) to medium (∼100 kW) and heavy-duty (sub-megawatt) auxiliary and power systems.

  12. Using the Nova target chamber for high-yield targets

    International Nuclear Information System (INIS)

    Pitts, J.H.

    1987-01-01

    The existing 2.2-m-radius Nova aluminum target chamber, coated and lined with boron-seeded carbon shields, is proposed for use with 1000-MJ-yield targets in the next laser facility. The laser beam and diagnostic holes in the target chamber are left open and the desired 10 -2 Torr vacuum is maintained both inside and outside the target chamber; a larger target chamber room is the vacuum barrier to the atmosphere. The hole area available is three times that necessary to maintain a maximum fluence below 12 J/cm 2 on optics placed at a radius of 10 m. Maximum stress in the target chamber wall is 73 MPa, which complies with the intent of the ASME Pressure Vessel Code. However, shock waves passing through the inner carbon shield could cause it to comminute. We propose tests and analyses to ensure that the inner carbon shield survives the environment. 13 refs

  13. Mutation induction and evaluation of high yield rice mutants

    International Nuclear Information System (INIS)

    Abdul Rahim Harun; Sobri Husein; Rusli Ibrahim

    2006-01-01

    The successful use of plant breeding for improving crops requires the existence of genetic variation of useful traits. Unfortunately, the desired variation is often lacking. However, radiation has been used to induce mutations and thereby generate genetic variation from which desired mutants may be selected. Mutation induction has become a proven way of creating variation within a crop variety. It offers the possibility of inducing desired attributes that either cannot be expressed in nature or have been lost during evolution. Rice is security food crop in Malaysia. Efforts were undertaken to enhance rice yield from 4.0 tones per hectare in 1995 to 5.5 tones per hectare in 2010. Proper management and good varieties are two factors that require for enhancing yield of rice. In this research, purified seeds of MR211 and MR219 were gamma irradiated at 100 to 400 Gray and sown for planting as M1 generation at MARDI experimental plot. The M2 population was sown in bulk with population size around 15,000 to 20,000 plants. Individual plant selection was carried out at maturity and each selected plant became a mutant line of M3 generation. Agronomic trial of M3 mutants lines were conducted in Mardi, Tanjung Karang, Selangor. About 115 of selected mutant lines were evaluated. Each row of those mutant lines were planted in two rows at planting distance of 25cm within and between rows. These mutant lines were visually observed and data were recorded in each of every mutant line. (Author)

  14. Limited Seed and Seed Yield Response of Calendula to Applied Nitrogen Does Not Justify Risk of Environmental Damage from High Urea Application Rates

    Directory of Open Access Journals (Sweden)

    Jane M. F. Johnson

    2018-03-01

    Full Text Available Calendula (Calendula officinalis L. seed, due to its high calendic acid content, is recognized as a potential environmentally safe substitute for volatile organic compounds. Agronomic guidelines for nitrogen (N management to produce calendula seed oil on a commercial scale are limited. Post-harvest soil N has the potential to move off-farm and contribute to water quality degradation (e.g., hypoxia in the Gulf of Mexico. Establishing N management guidelines should consider agronomic response and potential environmental risk. Calendula seed and oil yield, oil content, harvest index, N use, seed N use efficiency, oil N use efficiency, agronomic efficiency, vegetative growth, and the amount of residual soil-N following harvest response to five urea N rates (0, 34, 67, 134, and 202 kg N ha−1 were assessed in a replicated field study repeated for two growing seasons. Seed yield increased with N rate, but because of the low N conversion efficiency, there appeared to be minimal yield gains in applying N beyond 34 kg ha−1. The lowest amount of soil-N left underutilized in the soil was predicted to occur at 39 kg N ha−1 and was adequate for seed and seed oil commercial calendula production on a Mollisol in the Northern Midwest United States.

  15. High-yield growth of vertically aligned carbon nanotubes on a continuously moving substrate

    International Nuclear Information System (INIS)

    Guzman de Villoria, R; Hart, A J; Steiner, S A III; Wardle, B L; Figueredo, S L; Slocum, A H

    2009-01-01

    Vertically aligned carbon nanotube (CNT) arrays are grown on a moving substrate, demonstrating continuous growth of nanoscale materials with long-range order. A cold-wall chamber with an oscillating moving platform is used to locally heat a silicon growth substrate coated with an Fe/Al 2 O 3 catalyst film for CNT growth via chemical vapor deposition. The reactant gases are introduced over the substrate through a directed nozzle to attain high-yield CNT growth. Aligned multi-wall carbon nanotube arrays (or 'forests') with heights of ∼1 mm are achieved at substrate speeds up to 2.4 mm s -1 . Arrays grown on moving substrates at different velocities are studied in order to identify potential physical limitations of repeatable and fast growth on a continuous basis. No significant differences are noted between static and moving growth as characterized by scanning electron microscopy and Raman spectroscopy, although overall growth height is marginally reduced at the highest substrate velocity. CNT arrays produced on moving substrates are also found to be comparable to those produced through well-characterized batch processes consistent with a base-growth mechanism. Growth parameters required for the moving furnace are found to differ only slightly from those used in a comparable batch process; thermal uniformity appears to be the critical parameter for achieving large-area uniform array growth. If the continuous-growth technology is combined with a reaction zone isolation scheme common in other types of processing (e.g., in the manufacture of carbon fibers), large-scale dense and aligned CNT arrays may be efficiently grown and harvested for numerous applications including providing interlayers for advanced composite reinforcement and improved electrical and thermal transport.

  16. High-yield growth of vertically aligned carbon nanotubes on a continuously moving substrate.

    Science.gov (United States)

    Guzmán de Villoria, R; Figueredo, S L; Hart, A J; Steiner, S A; Slocum, A H; Wardle, B L

    2009-10-07

    Vertically aligned carbon nanotube (CNT) arrays are grown on a moving substrate, demonstrating continuous growth of nanoscale materials with long-range order. A cold-wall chamber with an oscillating moving platform is used to locally heat a silicon growth substrate coated with an Fe/Al2O3 catalyst film for CNT growth via chemical vapor deposition. The reactant gases are introduced over the substrate through a directed nozzle to attain high-yield CNT growth. Aligned multi-wall carbon nanotube arrays (or 'forests') with heights of approximately 1 mm are achieved at substrate speeds up to 2.4 mm s(-1). Arrays grown on moving substrates at different velocities are studied in order to identify potential physical limitations of repeatable and fast growth on a continuous basis. No significant differences are noted between static and moving growth as characterized by scanning electron microscopy and Raman spectroscopy, although overall growth height is marginally reduced at the highest substrate velocity. CNT arrays produced on moving substrates are also found to be comparable to those produced through well-characterized batch processes consistent with a base-growth mechanism. Growth parameters required for the moving furnace are found to differ only slightly from those used in a comparable batch process; thermal uniformity appears to be the critical parameter for achieving large-area uniform array growth. If the continuous-growth technology is combined with a reaction zone isolation scheme common in other types of processing (e.g., in the manufacture of carbon fibers), large-scale dense and aligned CNT arrays may be efficiently grown and harvested for numerous applications including providing interlayers for advanced composite reinforcement and improved electrical and thermal transport.

  17. Frequency of cardiac arrhythmias in high and low- yielding dairy cows

    Directory of Open Access Journals (Sweden)

    Afshin Jafari Dehkordi

    2014-06-01

    Full Text Available Electrocardiography (ECG may be used to recognize cardiac disorders. Levels of milk production may change the serum electrolytes which its imbalance has a role in cardiac arrhythmia. Fifty high yielding and fifty low yielding Holstein dairy cows were used in this study. Electrocardiography was recorded by base-apex lead and blood samples were collected from jugular vein for measurement of serum elements such as sodium, potassium, calcium, phosphorous, iron and magnesium. Cardiac dysrhythmias were detected more frequent in low yielding Holstein cows (62.00% compared to high yielding Holstein cows (46.00%. The cardiac dysrhythmias that were observed in low yielding Holstein cows included sinus arrhythmia (34.70%, wandering pacemaker (22.45 %, bradycardia (18.37%, tachycardia (10.20%, atrial premature beat (2.04%, sinoatrial block (2.04%, atrial fibrillation (8.16% and atrial tachycardia (2.04%. The cardiac dysrhythmias were observed in high yielding Holstein cows including, sinus arrhythmia (86.95% and wandering pacemaker (13.05%. Also, notched P wave was observed to be 30% and 14% in high- and low- yielding Holstein cows respectively. The serum calcium concentration of low yielding Holstein cows was significantly lower than that of high yielding Holstein cows. There was not any detectable significant difference in other serum elements between high- and low- yielding Holstein cows. Based on the result of present study, could be concluded that low serum concentration of calcium results to more frequent dysrhythmias in low yielding Holstein cows.

  18. MEMS-based thick film PZT vibrational energy harvester

    DEFF Research Database (Denmark)

    Lei, Anders; Xu, Ruichao; Thyssen, Anders

    2011-01-01

    We present a MEMS-based unimorph silicon/PZT thick film vibrational energy harvester with an integrated proof mass. We have developed a process that allows fabrication of high performance silicon based energy harvesters with a yield higher than 90%. The process comprises a KOH etch using a mechan......We present a MEMS-based unimorph silicon/PZT thick film vibrational energy harvester with an integrated proof mass. We have developed a process that allows fabrication of high performance silicon based energy harvesters with a yield higher than 90%. The process comprises a KOH etch using...... a mechanical front side protection of an SOI wafer with screen printed PZT thick film. The fabricated harvester device produces 14.0 μW with an optimal resistive load of 100 kΩ from 1g (g=9.81 m s-2) input acceleration at its resonant frequency of 235 Hz....

  19. Path and correlation analysis of perennial ryegrass (Lolium perenne L.) seed yield components

    DEFF Research Database (Denmark)

    Abel, Simon; Gislum, René; Boelt, Birte

    2017-01-01

    Maximum perennial ryegrass seed production potential is substantially greater than harvested yields with harvested yields representing only 20% of calculated potential. Similar to wheat, maize and other agriculturally important crops, seed yield is highly dependent on a number of interacting seed...... yield components. This research was performed to apply and describe path analysis of perennial ryegrass seed yield components in relation to harvested seed yields. Utilising extensive yield components which included subdividing reproductive inflorescences into five size categories, path analysis...... was undertaken assuming a unidirectional causal-admissible relationship between seed yield components and harvested seed yield in six commercial seed production fields. Both spikelets per inflorescence and florets per spikelet had a significant (p seed yield; however, total...

  20. Separating heat stress from moisture stress: analyzing yield response to high temperature in irrigated maize

    Science.gov (United States)

    Carter, Elizabeth K.; Melkonian, Jeff; Riha, Susan J.; Shaw, Stephen B.

    2016-09-01

    Several recent studies have indicated that high air temperatures are limiting maize (Zea mays L.) yields in the US Corn Belt and project significant yield losses with expected increases in growing season temperatures. Further work has suggested that high air temperatures are indicative of high evaporative demand, and that decreases in maize yields which correlate to high temperatures and vapor pressure deficits (VPD) likely reflect underlying soil moisture limitations. It remains unclear whether direct high temperature impacts on yields, independent of moisture stress, can be observed under current temperature regimes. Given that projected high temperature and moisture may not co-vary the same way as they have historically, quantitative analyzes of direct temperature impacts are critical for accurate yield projections and targeted mitigation strategies under shifting temperature regimes. To evaluate yield response to above optimum temperatures independent of soil moisture stress, we analyzed climate impacts on irrigated maize yields obtained from the National Corn Growers Association (NCGA) corn yield contests for Nebraska, Kansas and Missouri. In irrigated maize, we found no evidence of a direct negative impact on yield by daytime air temperature, calculated canopy temperature, or VPD when analyzed seasonally. Solar radiation was the primary yield-limiting climate variable. Our analyses suggested that elevated night temperature impacted yield by increasing rates of phenological development. High temperatures during grain-fill significantly interacted with yields, but this effect was often beneficial and included evidence of acquired thermo-tolerance. Furthermore, genetics and management—information uniquely available in the NCGA contest data—explained more yield variability than climate, and significantly modified crop response to climate. Thermo-acclimation, improved genetics and changes to management practices have the potential to partially or completely

  1. Differential expression of CURS gene during various growth stages, climatic condition and soil nutrients in turmeric (Curcuma longa): Towards site specific cultivation for high curcumin yield.

    Science.gov (United States)

    Sandeep, I Sriram; Das, Suryasnata; Nasim, Noohi; Mishra, Antaryami; Acharya, Laxmikanta; Joshi, Raj Kumar; Nayak, Sanghamitra; Mohanty, Sujata

    2017-09-01

    Curcuma longa L., accumulates substantial amount of curcumin and essential oil. Little is known about the differential expression of curcumin synthase (CURS) gene and consequent curcumin content variations at different agroclimatic zones. The present study aimed to evaluate the effect of climate, soil and harvesting phase on expression of CURS gene for curcumin yield in two high yielding turmeric cultivars. Expression of CURS gene at different experimental zones as well as at different harvesting phase was studied through transcriptional analysis by qRT-PCR. Curcumin varied from 1.5 to 5% and 1.4-5% in Surama and Roma respectively. The expression of CURS also varied from 0.402 to 5.584 fold in Surama and 0.856-5.217 fold in Roma. Difference in curcumin content at a particular zone varied among different harvesting period from 3.95 to 4.31% in Surama and 3.57-3.83% in Roma. Expression of CURS gene was also effected by harvesting time of the rhizome which varied from 7.389 to 16.882 fold in Surama and 4.41-8.342 fold in Roma. The CURS gene expression was found regardless of variations in curcumin content at different experimental zones. This may be due to the effects of soil and environmental variables. Expression was positively correlated with curcumin content with different harvesting time at a particular zone. This find indicates effect of soil and environment on molecular and biochemical dynamics of curcumin biosynthesis and could be useful in genetic improvement of turmeric. Copyright © 2017 Elsevier Masson SAS. All rights reserved.

  2. High yield of low-energy pions from a high-energy primary proton beam

    International Nuclear Information System (INIS)

    Bertin, A.; Capponi, S.; De Castro, S.

    1987-01-01

    This paper presents the results of the first measurement on the yield of pions with momentum smaller than 220 MeV/c, produced by a 300 GeV/c proton beam. The measurements, performed at the CERN super proton synchrotron using tungsten production targets of different lengths, are discussed referring to the possibility of extending to high-energy laboratories the access to fundamental research involving low-energy pions and muons

  3. A portable high-efficiency electromagnetic energy harvesting system using supercapacitors for renewable energy applications in railroads

    International Nuclear Information System (INIS)

    Zhang, Xingtian; Zhang, Zutao; Pan, Hongye; Salman, Waleed; Yuan, Yanping; Liu, Yujie

    2016-01-01

    Graphical abstract: In this study, we develop a portable high-efficiency electromagnetic energy harvesting system with supercapacitors that converts the energy of track vibrations into electricity. The generated electricity is stored in the supercapacitors and used in remote areas for safety facilities or in standby power supplies for rail-side equipment. The proposed system consists of a mechanical transmission and a rectifier. Acting as the energy input and transmission, Gears and a rack amplify the small vibrations of the track, and one-way bearings enhance efficiency by transforming bidirectional motion to unidirectional rotation. Supercapacitors are used in the energy harvesting system for the first time. The supercapacitors permit the storage of energy from rapidly changing transient currents and a steady power supply for external loads. The proposed system is demonstrated through dynamic simulations, which show the rapid response of the system. An efficiency of 55.5% is demonstrated in bench tests, verifying that the proposed electromagnetic energy harvesting system is effective and practical in renewable energy applications for railroads. - Highlights: • A frequently ignored source of energy, railroad track vibrations, is harvested. • A novel conversion mechanism is designed to maximize efficiency. • Supercapacitors are included in the electromagnetic energy harvesting system. • A portable design is proposed for wider application. - Abstract: As the demand for alternative sources of energy has increased, harvesting abundant environmental energy such as vibration energy including track vibrations in railway systems has attracted greater attention. In this study, we develop a portable high-efficiency electromagnetic energy harvesting system with supercapacitors that converts the energy of track vibrations into electricity. The generated electricity is stored in the supercapacitors and used in remote areas for safety facilities or in standby power

  4. High School Student Physics Research Experience Yields Positive Results

    Science.gov (United States)

    Podolak, K. R.; Walters, M. J.

    2016-01-01

    All high school students that wish to continue onto college are seeking opportunities to be competitive in the college market. They participate in extra-curricular activities which are seen to foster creativity and the skills necessary to do well in the college environment. In the case of students with an interest in physics, participating in a…

  5. Carbon isotope discrimination as a selection tool for high water use efficiency and high crop yields

    International Nuclear Information System (INIS)

    Kumarasinghe, K.S.; Kirda, C.; Bowen, G.D.; Zapata, F.; Awonaike, K.O.; Holmgren, E.; Arslan, A.; De Bisbal, E.C.; Mohamed, A.R.A.G.; Montenegro, A.

    1996-01-01

    Results of back-up research conducted at the FAO/IAEA Agriculture and Biotechnology Laboratory in support of the FAO/IAEA Co-ordinated Research Programme on the Use of Isotope Studies on Increasing and Stabilizing Plant Productivity in Low Phosphate and Semi-arid and Sub-humid Soils of the Tropics and Sub-tropics, are presented here. Neutron probe measurements confirmed the earlier reports of a strong correlation of Δ with grain yield and water use efficiency of wheat. High soil gypsum content and soil salinity, a wide spread problem in soils of arid and semi-arid climatic zones, do not interfere with the association of Δ with crop yields, provided plants are grown in similar soil water status and soil fertility level. Results of a glasshouse experiment using selected cowpea genotypes showed that Δ values measured at flowering stage positively correlated with total dry matter production and percent N 2 derived from atmosphere (%Ndfa), contributing to an earlier report from the laboratory that it may be possible to use Δ values for screening of leguminous crops for high N 2 fixation potential. 13 C isotope discrimination in the leaves of Gliricidia sepium was measured to examine if the technique could be extended to studies with trees. Results of a glasshouse experiment with 18 provenances of Gliricidia sepium showed highly significant correlations of Δ with total dry matter production, water use efficiency and total N accumulated through biological nitrogen fixation. Although the correlation of Δ with water use efficiency and dry matter yield are relatively clear and better understood, the correlation with nitrogen fixation still needs a closer examination under different environmental conditions and with different species. While 13 C isotope discrimination may be a valuable tool for identifying annual crops with high water use efficiency and high yield potential, it may be more attractive for tree species considering the long growth periods taken for trees

  6. Gamma rays induced bold seeded high yielding mutant in chickpea

    International Nuclear Information System (INIS)

    Wani, A.A.; Anis, M.

    2001-01-01

    variety (12.64±0.14g). This ultimately resulted in an increase in the overall yield of the mutant plant (38.86±1.69g) as compared to Pusa-212 (30.05±0.59g). Gamma ray induced bold seeded mutants have been reported earlier by different workers. The decrease in the number of seeds per pod and pods/plant and increase in seed weight is evidence of the fact that each trait is affected independently by the mutagenic treatment. Although the mutant was morphologically distinct, cytologically it was normal. There were 8 perfect bivalents at metaphase and the anaphase segregation was normal. It is concluded that bold seeded mutant may be utilized in various breeding programs as a donor parent for boldness character of the mutant. On the other hand the mutant may also itself be improved through crosses with other parents to accommodate more seeds in its large sized pod, which remained almost 50% empty

  7. Stabilising high energy orbit oscillations by the utilisation of centrifugal effects for rotating-tyre-induced energy harvesting

    Science.gov (United States)

    Zhang, Yunshun; Zheng, Rencheng; Nakano, Kimihiko; Cartmell, Matthew P.

    2018-04-01

    Nonlinear energy harvesters are frequently considered in preference to linear devices because they can potentially overcome the narrow frequency bandwidth limitations inherent to linear variants; however, the possibility of variable harvesting efficiency is raised for the nonlinear case. This paper proposes a rotational energy harvester which may be fitted into an automobile tyre, with the advantage that it may broaden the rotating frequency bandwidth and simultaneously stabilise high-energy orbit oscillations. By consideration of the centrifugal effects due to rotation, the overall restoring force will potentially be increased for a cantilever implemented within the harvester, and this manifests as an increase in its equivalent elastic stiffness. In addition, this study reveals that the initial potential well barriers become as shallow as those for a bistable system. When the rotational frequency increases beyond an identifiable boundary frequency, the system transforms into one with a potential barrier of a typical monostable system. On this basis, the inter-well motion of the bistable system can provide sufficient kinetic energy so that the cantilever maintains its high-energy orbit oscillation for monostable hardening behaviour. Furthermore, in a vehicle drive experiment, it has been shown that the effective rotating frequency bandwidth can be widened from 15 km/h-25 km/h to 10 km/h-40 km/h. In addition, it is confirmed that the centrifugal effects can improve the harvester performance, producing a mean power of 61 μW at a driving speed of 40 km/h, and this is achieved by stabilising the high-energy orbit oscillations of the rotational harvester.

  8. High transpiration efficiency increases pod yield under intermittent drought in dry and hot atmospheric conditions but less so under wetter and cooler conditions in groundnut (Arachis hypogaea (L.)).

    Science.gov (United States)

    Vadez, Vincent; Ratnakumar, Pasala

    2016-07-01

    Water limitation is a major yield limiting factor in groundnut and transpiration efficiency (TE) is considered the main target for improvement, but TE being difficult to measure it has mostly been screened with surrogates. The paper re-explore the contribution of TE to grain yield in peanut by using a novel experimental approach in which TE is measured gravimetrically throughout the crop life cycle, in addition to measurement of TE surrogates. Experimentation was carried out with the groundnut reference collection (n = 288), across seasons varying for the evaporative demand (vapor pressure deficit, VPD) and across both fully irrigated and intermittent water stress conditions. There was large genotypic variation for TE under water stress in both low and high VPD season but the range was larger (5-fold) in the high- than in the low-VPD season (2-fold). Under water stress in both seasons, yield was closely related to the harvest index (HI) while TE related directly to yield only in the high VPD season. After discounting the direct HI effect on yield, TE explained a large portion of the remaining yield variations in both seasons, although marginally in the low VPD season. By contrast, the total water extracted from the soil profile, which varied between genotypes, did not relate directly to pod yield and neither to the yield residuals unexplained by HI. Surrogates for TE (specific leaf area, SLA, and SPAD chlorophyll meter readings, SCMR) never showed any significant correlation to TE measurements. Therefore, TE is an important factor explaining yield differences in groundnut under high VPD environments, suggesting that stomatal regulation under high VPD, rather than high photosynthetic rate as proposed earlier, may have a key role to play in the large TE differences found, which open new opportunities to breed improved groundnut for high VPD.

  9. Clickstream data yields high-resolution maps of science

    Energy Technology Data Exchange (ETDEWEB)

    Bollen, Johan [Los Alamos National Laboratory; Van De Sompel, Herbert [Los Alamos National Laboratory; Hagberg, Aric [Los Alamos National Laboratory; Bettencourt, Luis [Los Alamos National Laboratory; Chute, Ryan [Los Alamos National Laboratory; Rodriguez, Marko A [Los Alamos National Laboratory; Balakireva, Lyudmila [Los Alamos National Laboratory

    2009-01-01

    Intricate maps of science have been created from citation data to visualize the structure of scientific activity. However, most scientific publications are now accessed online. Scholarly web portals record detailed log data at a scale that exceeds the number of all existing citations combined. Such log data is recorded immediately upon publication and keeps track of the sequences of user requests (clickstreams) that are issued by a variety of users across many different domains. Given these advantagees of log datasets over citation data, we investigate whether they can produce high-resolution, more current maps of science.

  10. Comparison of different options for harvest of a therapeutic protein product from high cell density yeast fermentation broth.

    Science.gov (United States)

    Wang, Alice; Lewus, Rachael; Rathore, Anurag S

    2006-05-05

    Recovery of therapeutic protein from high cell density yeast fermentations at commercial scale is a challenging task. In this study, we investigate and compare three different harvest approaches, namely centrifugation followed by depth filtration, centrifugation followed by filter-aid enhanced depth filtration, and microfiltration. This is achieved by presenting a case study involving recovery of a therapeutic protein from Pichia pastoris fermentation broth. The focus of this study is on performance of the depth filtration and the microfiltration steps. The experimental data has been fitted to the conventional models for cake filtration to evaluate specific cake resistance and cake compressibility. In the case of microfiltration, the experimental data agrees well with flux predicted by shear induced diffusion model. It is shown that, under optimal conditions, all three options can deliver the desired product recovery ( >80%), harvest time ( making a final decision on a harvesting approach.

  11. Investigating Forest Harvest Effects on DOC Concentration and Quality: An In Situ, High Resolution Approach to Quantifying DOC Export Dynamics

    Science.gov (United States)

    Jollymore, A. J.; Johnson, M. S.; Hawthorne, I.

    2013-12-01

    Justification: Forest harvest effects on water quality can signal alterations in hydrologic and ecologic processes incurred as a result of forest harvest activities. Organic matter (OM), specifically dissolved organic carbon (DOC), plays a number of important roles mediating UV-light penetration, redox reactivity and microbial activity within aquatic ecosystems. Quantification of DOC is typically pursued via grab sampling followed by chemical or spectrophotometric analysis, limiting the temporal resolution obtained as well as the accuracy of export calculations. The advent of field-deployable sensors capable of measuring DOC concentration and certain quality characteristics in situ provides the ability to observe dynamics at temporal scales necessary for accurate calculation of DOC flux, as well as the observation of dynamic changes in DOC quality on timescales impossible to observe through grab sampling. Methods: This study utilizes a field deployable UV-Vis spectrophotometer (spectro::lyzer, s::can, Austria) to investigate how forest harvest affects DOC export. The sensor was installed at an existing hydrologic monitoring site at the outlet of a headwater stream draining a small (91 hectare) second growth Douglasfir-dominated catchment near Campbell River on Vancouver Island, British Columbia. Measurement began late in 2009, prior to forest harvest and associated activities such as road building (which commenced in October 2010 and ended in early 2011), and continues to present. During this time - encompassing the pre, during and post-harvest conditions - the absorbance spectrum of stream water from 200 to 750 nm was measured. DOC concentration and spectroscopic indices related to DOC quality (including SUVA, which relates to the concentration of aromatic carbon, and spectral slope) were subsequently calculated for each spectra obtained at 30-minute intervals. Results and conclusions: High frequency measurements of DOC show that overall export of OM increased in

  12. High lysine and high yielding mutants in wheat (Triticum aestivum) L

    International Nuclear Information System (INIS)

    Mohammad, T.; Mahmood, F.; Ahmad, A.; Sattar, A.; Khan, I.

    1988-01-01

    The dry seeds of the variety Lu-26 were irradiated with 20 krad of gamma rays. In M 2 about 300 mutant plants were selected for short stature, rust resistance and other desirable traits. As a result of further selection, in M 6 , eight superior lines were finally identified. The agronomic characteristics of these mutants, the parent variety (Lu-26) and a standard check variety (Pak-81) are shown. The selected mutants and commercially grown cultivars (Lu-26 and Pak-81) were studied for total protein content and amino acid pattern. The mutants WM-89-1, WM-6-17 and WM-81-2 showing high yield also contained comparatively high amounts of methionine and lysine. The lysine contents were 565, 410, and 370 mg/100g in the mutants WM-89-1, WM-6-17 and WM-81-2, respectively against a range value of 210-370 mg/100g in other mutants and 250-320 in the commercial cultivars. The mutant WM-81-2 was comparable to WM-56-1-5 in lysine content. The results of these experiments show a possibility of developing varieties having high yield and high amounts of essential amino acids such as lysine and methionine

  13. Clickstream Data Yields High-Resolution Maps of Science

    Science.gov (United States)

    Bollen, Johan; Van de Sompel, Herbert; Rodriguez, Marko A.; Balakireva, Lyudmila

    2009-01-01

    Background Intricate maps of science have been created from citation data to visualize the structure of scientific activity. However, most scientific publications are now accessed online. Scholarly web portals record detailed log data at a scale that exceeds the number of all existing citations combined. Such log data is recorded immediately upon publication and keeps track of the sequences of user requests (clickstreams) that are issued by a variety of users across many different domains. Given these advantages of log datasets over citation data, we investigate whether they can produce high-resolution, more current maps of science. Methodology Over the course of 2007 and 2008, we collected nearly 1 billion user interactions recorded by the scholarly web portals of some of the most significant publishers, aggregators and institutional consortia. The resulting reference data set covers a significant part of world-wide use of scholarly web portals in 2006, and provides a balanced coverage of the humanities, social sciences, and natural sciences. A journal clickstream model, i.e. a first-order Markov chain, was extracted from the sequences of user interactions in the logs. The clickstream model was validated by comparing it to the Getty Research Institute's Architecture and Art Thesaurus. The resulting model was visualized as a journal network that outlines the relationships between various scientific domains and clarifies the connection of the social sciences and humanities to the natural sciences. Conclusions Maps of science resulting from large-scale clickstream data provide a detailed, contemporary view of scientific activity and correct the underrepresentation of the social sciences and humanities that is commonly found in citation data. PMID:19277205

  14. Clickstream data yields high-resolution maps of science.

    Science.gov (United States)

    Bollen, Johan; Van de Sompel, Herbert; Hagberg, Aric; Bettencourt, Luis; Chute, Ryan; Rodriguez, Marko A; Balakireva, Lyudmila

    2009-01-01

    Intricate maps of science have been created from citation data to visualize the structure of scientific activity. However, most scientific publications are now accessed online. Scholarly web portals record detailed log data at a scale that exceeds the number of all existing citations combined. Such log data is recorded immediately upon publication and keeps track of the sequences of user requests (clickstreams) that are issued by a variety of users across many different domains. Given these advantages of log datasets over citation data, we investigate whether they can produce high-resolution, more current maps of science. Over the course of 2007 and 2008, we collected nearly 1 billion user interactions recorded by the scholarly web portals of some of the most significant publishers, aggregators and institutional consortia. The resulting reference data set covers a significant part of world-wide use of scholarly web portals in 2006, and provides a balanced coverage of the humanities, social sciences, and natural sciences. A journal clickstream model, i.e. a first-order Markov chain, was extracted from the sequences of user interactions in the logs. The clickstream model was validated by comparing it to the Getty Research Institute's Architecture and Art Thesaurus. The resulting model was visualized as a journal network that outlines the relationships between various scientific domains and clarifies the connection of the social sciences and humanities to the natural sciences. Maps of science resulting from large-scale clickstream data provide a detailed, contemporary view of scientific activity and correct the underrepresentation of the social sciences and humanities that is commonly found in citation data.

  15. Clickstream data yields high-resolution maps of science.

    Directory of Open Access Journals (Sweden)

    Johan Bollen

    Full Text Available BACKGROUND: Intricate maps of science have been created from citation data to visualize the structure of scientific activity. However, most scientific publications are now accessed online. Scholarly web portals record detailed log data at a scale that exceeds the number of all existing citations combined. Such log data is recorded immediately upon publication and keeps track of the sequences of user requests (clickstreams that are issued by a variety of users across many different domains. Given these advantages of log datasets over citation data, we investigate whether they can produce high-resolution, more current maps of science. METHODOLOGY: Over the course of 2007 and 2008, we collected nearly 1 billion user interactions recorded by the scholarly web portals of some of the most significant publishers, aggregators and institutional consortia. The resulting reference data set covers a significant part of world-wide use of scholarly web portals in 2006, and provides a balanced coverage of the humanities, social sciences, and natural sciences. A journal clickstream model, i.e. a first-order Markov chain, was extracted from the sequences of user interactions in the logs. The clickstream model was validated by comparing it to the Getty Research Institute's Architecture and Art Thesaurus. The resulting model was visualized as a journal network that outlines the relationships between various scientific domains and clarifies the connection of the social sciences and humanities to the natural sciences. CONCLUSIONS: Maps of science resulting from large-scale clickstream data provide a detailed, contemporary view of scientific activity and correct the underrepresentation of the social sciences and humanities that is commonly found in citation data.

  16. CO₂ enrichment can produce high red leaf lettuce yield while increasing most flavonoid glycoside and some caffeic acid derivative concentrations.

    Science.gov (United States)

    Becker, Christine; Kläring, Hans-Peter

    2016-05-15

    Carbon dioxide (CO2) enrichment is a common practice in greenhouses to increase crop yields up to 30%. Yet, reports on the effect on foliar phenolic compounds vary. We studied the effect on two red leaf lettuce cultivars, grown for 25 days in growth chambers at CO2 concentrations of 200 or 1,000 ppm, with some plants exchanged between treatments after 11 days. As expected, head mass increased with higher CO2 concentration. Regression analysis, corrected for head mass, showed increased concentrations of most flavonoid glycosides at high CO2 concentrations while only some caffeic acid derivatives were increased, and not uniformly in both cultivars. Sugar concentrations increased with CO2 concentration. Generally, conditions in the 10 days before harvest determined concentrations. We suspect that phenolic compounds were mainly accumulated because plenty of precursors were available. The results indicate that CO2 enrichment can result in high yields of red leaf lettuce rich in phenolic compounds. Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.

  17. Growth and Yield Responses of Green Pepper (Capsicum annum L. to Manure Rates under Field and High Tunnel Conditions

    Directory of Open Access Journals (Sweden)

    Ima-obong I. DOMINIC

    2017-03-01

    Full Text Available The present study was conducted to determine growth and yield responses of green pepper to varying manure rates under field and high tunnel conditions. Experiment 1 was a pot experiment to evaluate three rates (0.5 and 10 t/ha of poultry manure (PM on green pepper production under high tunnel and open field conditions. Experiment 2 was to determine the performance of green pepper as influenced by different manure rates (0, 5 and 10 t/ha of PM, 300 kg/ha of NPK, 5 t/ha of PM + 200 kg of NPK and 10 t/ha of PM + 100 kg of NPK on the field. High tunnel produced about 3.1 fruits/plant that weighted 102.8 g, which was significantly higher than open field experiment in which 1.7 fruits/plant, with a medium weight of 32.3 g were noted. High tunnel enhanced successful production of green pepper during rainy season, whereas the open field production during the same season was near failure. Application of 10 t/ha of PM produced significantly larger fruits in the pot experiment. Good fertilizer effects on growth and yield components were recorded for the field study. Plant height, number of leaves and branches, number and weight of harvested fruit followed similar trend in 5 and 10 t/ha of PM which gave statistically similar results, and provided the best performance during the experiment. Application of 5 t/ha of PM produced the highest total fruits yield.

  18. Carbon isotope discrimination as a selection tool for high water use efficiency and high crop yields

    Energy Technology Data Exchange (ETDEWEB)

    Kumarasinghe, K S; Kirda, C; Bowen, G D [Joint FAO/IAEA Div. of Nuclear Techniques in Food and Agriculture, Vienna (Austria). Soil Fertility, Irrigation and Crop Production Section; Zapata, F; Awonaike, K O; Holmgren, E; Arslan, A; De Bisbal, E C; Mohamed, A R.A.G.; Montenegro, A [FAO/IAEA Agriculture and Biotechnology Lab., Seibersdorf (Austria). Soils Science Unit

    1996-07-01

    Results of back-up research conducted at the FAO/IAEA Agriculture and Biotechnology Laboratory in support of the FAO/IAEA Co-ordinated Research Programme on the Use of Isotope Studies on Increasing and Stabilizing Plant Productivity in Low Phosphate and Semi-arid and Sub-humid Soils of the Tropics and Sub-tropics, are presented here. Neutron probe measurements confirmed the earlier reports of a strong correlation of {Delta} with grain yield and water use efficiency of wheat. High soil gypsum content and soil salinity, a wide spread problem in soils of arid and semi-arid climatic zones, do not interfere with the association of {Delta} with crop yields, provided plants are grown in similar soil water status and soil fertility level. Results of a glasshouse experiment using selected cowpea genotypes showed that {Delta} values measured at flowering stage positively correlated with total dry matter production and percent N{sub 2} derived from atmosphere (%Ndfa), contributing to an earlier report from the laboratory that it may be possible to use {Delta} values for screening of leguminous crops for high N{sub 2} fixation potential. {sup 13}C isotope discrimination in the leaves of Gliricidia sepium was measured to examine if the technique could be extended to studies with trees. Results of a glasshouse experiment with 18 provenances of Gliricidia sepium showed highly significant correlations of {Delta} with total dry matter production, water use efficiency and total N accumulated through biological nitrogen fixation. Although the correlation of {Delta} with water use efficiency and dry matter yield are relatively clear and better understood, the correlation with nitrogen fixation still needs a closer examination under different environmental conditions and with different species. (Abstract Truncated)

  19. Evolving of mutant lines resistant to lodging, blast, and high yield in rice by induce mutation using gamma ray (physical mutagen)

    International Nuclear Information System (INIS)

    Majd, F.; Rahimi, M.; Rezazadeh, M.

    2003-01-01

    Induction of mutation for the purpose of producing variations in the gene pool has been used in recent years. In this experiment the locally adapted rice C V Moosa-Tarom was used as a high quality, tall and very lodging susceptible mutation material. The main purpose of this project was to evolve lodging resistant mutants of high yielding. The elite seeds of Moosa-Tarom variety after moisture regulation were exposed to 100, 200 and 300 Gy from Cobalt 60 source at the Nuclear Research Center. The irradiated seeds were sown in the field along with a comparable number of unirradiated seeds taken as control. All the first panicles of M1 plants were individually harvested and classified according to the dose rate as M2 material . Among M2 plant populations 203 plants that appeared from the agronomic point of view, along with a number of on unirradiated seeds, were selected and moved to the next generations. During subsequent screening for three generations (M 3-M 5) and due to lodging resistant, height and efficient factors of yield potential some mutant lines were harvested. From these lines in a preliminary and advanced randomized complete design agronomic traits, 13 promising lines were selected. From the experiment, line 43-3 were confirmed, which is characterized by lodging resistant and high yield. This line showed relative superiority and introduced to Rice Research Institute

  20. The effect of high concentrations of glufosinate ammonium on the yield components of transgenic spring wheat (Triticum aestivum L.) constitutively expressing the bar gene.

    Science.gov (United States)

    Áy, Zoltán; Mihály, Róbert; Cserháti, Mátyás; Kótai, Éva; Pauk, János

    2012-01-01

    We present an experiment done on a bar(+) wheat line treated with 14 different concentrations of glufosinate ammonium-an effective component of nonselective herbicides-during seed germination in a closed experimental system. Yield components as number of spikes per plant, number of grains per spike, thousand kernel weight, and yield per plant were thoroughly analysed and statistically evaluated after harvesting. We found that a concentration of glufosinate ammonium 5000 times the lethal dose was not enough to inhibit the germination of transgenic plants expressing the bar gene. Extremely high concentrations of glufosinate ammonium caused a bushy phenotype, significantly lower numbers of grains per spike, and thousand kernel weights. Concerning the productivity, we observed that concentrations of glufosinate ammonium 64 times the lethal dose did not lead to yield depression. Our results draw attention to the possibilities implied in the transgenic approaches.

  1. The Effect of High Concentrations of Glufosinate Ammonium on the Yield Components of Transgenic Spring Wheat (Triticum aestivum L. Constitutively Expressing the bar Gene

    Directory of Open Access Journals (Sweden)

    Zoltán Áy

    2012-01-01

    Full Text Available We present an experiment done on a bar+ wheat line treated with 14 different concentrations of glufosinate ammonium—an effective component of nonselective herbicides—during seed germination in a closed experimental system. Yield components as number of spikes per plant, number of grains per spike, thousand kernel weight, and yield per plant were thoroughly analysed and statistically evaluated after harvesting. We found that a concentration of glufosinate ammonium 5000 times the lethal dose was not enough to inhibit the germination of transgenic plants expressing the bar gene. Extremely high concentrations of glufosinate ammonium caused a bushy phenotype, significantly lower numbers of grains per spike, and thousand kernel weights. Concerning the productivity, we observed that concentrations of glufosinate ammonium 64 times the lethal dose did not lead to yield depression. Our results draw attention to the possibilities implied in the transgenic approaches.

  2. High yield polyol synthesis of round- and sharp-end silver nanowires with high aspect ratio

    Energy Technology Data Exchange (ETDEWEB)

    Nekahi, A.; Marashi, S.P.H., E-mail: pmarashi@aut.ac.ir; Fatmesari, D. Haghshenas

    2016-12-01

    Long silver nanowires (average length of 28 μm, average aspect ratio of 130) with uniform diameter along their length were produced by polyol synthesis of AgNO{sub 3} in ethylene glycol in the presence of PVP as preferential growth agent. Nanowires were produced with no addition of chloride salts such as NaCl or CuCl{sub 2} (or other additives such as Na{sub 2}S) which are usually used for lowering reduction rate of Ag ions by additional etchant of O{sub 2}/Cl{sup −}. Lower reduction rate was obtained by increasing the injection time of PVP and AgNO{sub 3} solutions, which was the significant factor in the formation of nanowires. Therefore, there was enough time for reduced Ag atoms to be deposited preferentially in the direction of PVP chains, resulting in high yield (the fraction of nanowires in the products) of nanowires (more than 95%) with high aspect ratio. The produced nanowires had both round- and sharp-ends with pentagonal cross section. Higher energy level of Ag atoms in borders of MTPs, which increases the dissolution rate of precipitated atoms, in addition to partial melting of MTPs at high synthesis temperatures, leads to the curving of the surfaces of exposed (111) crystalline planes in some MTPs and the formation of round-end silver nanowires. - Highlights: • Long silver nanowires with high aspect ratio of 130 were produced. • More than 95% nanowires were produced in products. • The produced nanowires had round- and sharp-ends with pentagonal cross section. • Additives were needed neither for high yield synthesis nor for round-end nanowires. • Melting and etching of MTPs in high energy borders resulted to round-end nanowires.

  3. Breeding sesame for diseases and shatter resistant high yielding varieties with induced mutations

    International Nuclear Information System (INIS)

    Kang, C.W.

    2001-01-01

    ''Suwon 144'', derived from the cross between ''Danbaeckkae'' and mutant MY-74-2 and in spite of its higher yield and quality compared to the check variety, did not pass the nomination to the Committee of Main Crops New Varieties under the Ministry of Agriculture and Forestry, due to the decision of the committee to limit the number of new varieties in sesame as a minor crop in Korea. ''Suwon 144'' will be released again for a fifth year to RYT in 1998. 5,282 cross combinations and 4,341 lines including 1,388 crossings of F 1 were crossed and released to the experimental field of NCES in 1997. Mutants and their cross combinations were released and constituted more than half among them. Seeds of ''Suwon 152'' were treated with NaN 3 and tested for germinability. The other seeds were released and harvested in the experimental field and 419 mutant lines were selected among all the mutant lines. Mutants or materials from cross breeding with mutants occupied 71% (675) among a total of 952 promising lines in yield trials of OYT, PYT, AYT and RYT. For variability of NaN 3 induced genetic male sterile (GMS) mutants and development of restorer/s of GMS, GMS lines were planted, and male sterility (MS) expression evaluated on each line. The selected 4 MS lines with 50% MS were crossed in 22 combinations with 7 recommended varieties. For development of genic-cytoplasmic MS (GCMS) using NaN 3 induced GMS mutants, 40 recommended local Korean and introduced cultivars were crossed in 57 combinations with 4 selected GMS lines expressing 50% male sterility. Various and many sources of unique characteristics have been continuously created through induced mutations, such as determinate; dwarf, lodging,- Phytophthora blight- and shatter- resistant; indehiscent, seamless, taller, stronger thick stems, dense capsule bearing type, semi-dwarf, better maturity, male sterility, smaller seeds, pure white seed coat color and high yields. Lines with these induced desirable characteristics were

  4. High-resolution AFM topographs of Rubrivivax gelatinosus light-harvesting complex LH2

    Science.gov (United States)

    Scheuring, Simon; Reiss-Husson, Francoise; Engel, Andreas; Rigaud, Jean-Louis; Ranck, Jean-Luc

    2001-01-01

    Light-harvesting complexes 2 (LH2) are the accessory antenna proteins in the bacterial photosynthetic apparatus and are built up of αβ-heterodimers containing three bacteriochlorophylls and one carotenoid each. We have used atomic force microscopy (AFM) to investigate reconstituted LH2 from Rubrivivax gelatinosus, which has a C-terminal hydrophobic extension of 21 amino acids on the α-subunit. High-resolution topographs revealed a nonameric organization of the regularly packed cylindrical complexes incorporated into the membrane in both orientations. Native LH2 showed one surface which protruded by ∼6 Å and one that protruded by ∼14 Å from the membrane. Topographs of samples reconstituted with thermolysin-digested LH2 revealed a height reduction of the strongly protruding surface to ∼9 Å, and a change of its surface appearance. These results suggested that the α-subunit of R.gelatinosus comprises a single transmembrane helix and an extrinsic C-terminus, and allowed the periplasmic surface to be assigned. Occasionally, large rings (∼120 Å diameter) surrounded by LH2 rings were observed. Their diameter and appearance suggest the large rings to be LH1 complexes. PMID:11406579

  5. A distribution-free multi-factorial profiler for harvesting information from high-density screenings.

    Science.gov (United States)

    Besseris, George J

    2013-01-01

    Data screening is an indispensable phase in initiating the scientific discovery process. Fractional factorial designs offer quick and economical options for engineering highly-dense structured datasets. Maximum information content is harvested when a selected fractional factorial scheme is driven to saturation while data gathering is suppressed to no replication. A novel multi-factorial profiler is presented that allows screening of saturated-unreplicated designs by decomposing the examined response to its constituent contributions. Partial effects are sliced off systematically from the investigated response to form individual contrasts using simple robust measures. By isolating each time the disturbance attributed solely to a single controlling factor, the Wilcoxon-Mann-Whitney rank stochastics are employed to assign significance. We demonstrate that the proposed profiler possesses its own self-checking mechanism for detecting a potential influence due to fluctuations attributed to the remaining unexplainable error. Main benefits of the method are: 1) easy to grasp, 2) well-explained test-power properties, 3) distribution-free, 4) sparsity-free, 5) calibration-free, 6) simulation-free, 7) easy to implement, and 8) expanded usability to any type and size of multi-factorial screening designs. The method is elucidated with a benchmarked profiling effort for a water filtration process.

  6. Anoxic oscillating MBR for photosynthetic bacteria harvesting and high salinity wastewater treatment.

    Science.gov (United States)

    Qin, Lei; Liu, Qiuhua; Meng, Qin; Fan, Zheng; He, Jinzhe; Liu, Tao; Shen, Chong; Zhang, Guoliang

    2017-01-01

    In this study, photosynthetic bacteria (PSB) were first harvested by MBR with pendulum type oscillation (PTO) hollow fiber module in succession and on a large scale. Based on unique properties of PSB, PSB/MBR was successfully applied for high-salinity wastewater treatment. Compared with control PSB-MBR (CMBR), PSB/PTO-MBR exhibited more excellent organics removal, which was mainly attributed to much higher biomass production for utilization. Meanwhile, the influence of light irradiation and aeration on activity of PSB was investigated in detail. Results showed that PTO-MBR with 12h light irradiation proved to be a promising and economical alternative. The cycle of dark/light and anoxic had a positive effect on PSB cultivating. Moreover, PTO-MBR exhibited much higher flux than CMBR even if large amounts of biomass existed, which demonstrated that the strong shear stress on interface of liquid-membrane played important roles on membrane fouling reduction. Copyright © 2016 Elsevier Ltd. All rights reserved.

  7. A distribution-free multi-factorial profiler for harvesting information from high-density screenings.

    Directory of Open Access Journals (Sweden)

    George J Besseris

    Full Text Available Data screening is an indispensable phase in initiating the scientific discovery process. Fractional factorial designs offer quick and economical options for engineering highly-dense structured datasets. Maximum information content is harvested when a selected fractional factorial scheme is driven to saturation while data gathering is suppressed to no replication. A novel multi-factorial profiler is presented that allows screening of saturated-unreplicated designs by decomposing the examined response to its constituent contributions. Partial effects are sliced off systematically from the investigated response to form individual contrasts using simple robust measures. By isolating each time the disturbance attributed solely to a single controlling factor, the Wilcoxon-Mann-Whitney rank stochastics are employed to assign significance. We demonstrate that the proposed profiler possesses its own self-checking mechanism for detecting a potential influence due to fluctuations attributed to the remaining unexplainable error. Main benefits of the method are: 1 easy to grasp, 2 well-explained test-power properties, 3 distribution-free, 4 sparsity-free, 5 calibration-free, 6 simulation-free, 7 easy to implement, and 8 expanded usability to any type and size of multi-factorial screening designs. The method is elucidated with a benchmarked profiling effort for a water filtration process.

  8. Nitrogen rate and plant population effects on yield and yield ...

    African Journals Online (AJOL)

    STORAGESEVER

    2008-12-17

    Dec 17, 2008 ... density and nitrogen rate increased plant height, lowest pod height, harvest index and seed yield. ... since some combine harvester heads are unable to pick ..... as effected by population density and plant distribution.

  9. Wind energy harvesting with a piezoelectric harvester

    International Nuclear Information System (INIS)

    Wu, Nan; Wang, Quan; Xie, Xiangdong

    2013-01-01

    An energy harvester comprising a cantilever attached to piezoelectric patches and a proof mass is developed for wind energy harvesting, from a cross wind-induced vibration of the cantilever, by the electromechanical coupling effect of piezoelectric materials. The vibration of the cantilever under the cross wind is induced by the air pressure owing to a vortex shedding phenomenon that occurs on the leeward side of the cantilever. To describe the energy harvesting process, a theoretical model considering the cross wind-induced vibration on the piezoelectric coupled cantilever energy harvester is developed, to calculate the charge and the voltage from the harvester. The influences of the length and location of the piezoelectric patches as well as the proof mass on the generated electric power are investigated. Results show that the total generated electric power can be as high as 2 W when the resonant frequency of the cantilever harvester is close to the vortex shedding frequency. Moreover, a value of total generated electric power up to 1.02 W can be practically realized for a cross wind with a variable wind velocity of 9–10 m s −1 by a harvester with a length of 1.2 m. This research facilitates an effective and compact wind energy harvesting device. (paper)

  10. Highly efficient green light harvesting from Mg doped ZnO nanoparticles: Structural and optical studies

    Energy Technology Data Exchange (ETDEWEB)

    Sharma, Sarla, E-mail: mail2sarlasharma@gmail.com [Department of Physics, University of Rajasthan, Jaipur 302055 (India); Vyas, Rishi [Department of Physics, Malaviya National Institute of Technology, Jaipur 302017 (India); Sharma, Neha [Department of Physics, University of Rajasthan, Jaipur 302055 (India); Singh, Vidyadhar [Okinawa Institute of Science and Technology, Graduate University, Okinawa 9040495 (Japan); Singh, Arvind [Department of Physics, Institute of Chemical Technology, Mumbai 400 019 (India); Kataria, Vanjula; Gupta, Bipin Kumar [National Physical Laboratory (CSIR), New Delhi 110012 (India); Vijay, Y.K. [Department of Physics, University of Rajasthan, Jaipur 302055 (India)

    2013-03-05

    Graphical abstract: Demonstration of highly efficient green light emission harvesting from Mg doped ZnO nanoparticles were synthesized via facile wet chemical route with an average particle size ∼15 nm. The resulted nanoparticles exhibit intense green emission peaking at 530 nm upon 325 nm excitation. The photoluminescence (PL) intensity of visible emission depends upon the doping concentration of Mg. The PL intensity was found maximum up to 4% doping of Mg and beyond it exhibits a decrees in emission. The obtained highly luminescent green emission of ZnO nanoparticle would be an ultimate choice for next generation optoelectronics device materials. Highlights: ► Zn{sub 1−x}Mg{sub x}O nanoparticles were prepared by mechanochemical processing. ► High blue emission intensity was observed contrary to previous reports. ► Blue emission is suggested to be originating from the high density of defects. ► Defect density in as-milled condition is very high resulting in high emission. ► Mg promoted non-radiative recombination and lowered intensities. -- Abstract: Highly efficient green light emission was observed from Mg doped ZnO nanoparticles synthesized via facile wet chemical route with an average particle size ∼15 nm. The XRD analysis confirmed the growth of wurtzite phase of ZnO nanoparticles. Moreover, the optical properties of these nanoparticles were investigated by different spectroscopic techniques. The resulted nanoparticles exhibit intense green emission peaking at 530 nm (2.34 eV) upon 325 nm (3.81 eV) excitation. The photoluminescence (PL) intensity of visible emission depends upon the doping concentration of Mg. The PL intensity was found maximum up to 4% doping of Mg, and beyond it exhibits a decrees in emission. Furthermore, by varying the band gap from 3.50 to 3.61 eV, the PL spectra showed a near band edge (NBE) emission at wavelength around 370 nm (3.35 eV) and a broad deep level emission in the visible region. The obtained highly

  11. POD NUMBER AND PHOTOSYNTHESIS AS PHYSIOLOGICAL SELECTION CRITERIA IN SOYBEAN (Glycine max L. Merrill BREEDING FOR HIGH YIELD

    Directory of Open Access Journals (Sweden)

    S.M. Sitompul

    2015-02-01

    Full Text Available Field studies were conducted in two years using 638 F2 and 1185 F3 lines of selected 16 F1 and 15 F2 parent lines (³80 pods plant-1 to evaluate pod number and CO2 exchange rate (CER as selection criteria. Pod and seed number, and seed weight of individual lines were observed during harvesting time, and CER of randomly selected 32 F2 and 30 F3 lines was measured at initial seed filling stage. The selection of F2 lines based on pod number to generate F3 lines increased the average of seed yield by 39%, and pod number by 77% in F3 lines compared with F2 lines. A close relationships was found between seed weight and pod or seed number per plant. Net CER responded sensitively to a reduction of light in a short-term and showed 78% of F2 lines and all F3 lines with maximum CER (Pmax³20 mmolCO2.m-2.s-1. The ratio of pod number per plant and Pmax varied between lines and were used to group lines resulting in close relationships between Pmax and pod number. It is concluded that the use of pod number and CER (Pmax as selection criteria offers an alternative approach in soybean breeding for high yield.

  12. 31 CFR 356.21 - How are awards at the high yield or discount rate calculated?

    Science.gov (United States)

    2010-07-01

    ... discount rate calculated? 356.21 Section 356.21 Money and Finance: Treasury Regulations Relating to Money... high yield or discount rate calculated? (a) Awards to submitters. We generally prorate bids at the highest accepted yield or discount rate under § 356.20(a)(2) of this part. For example, if 80.15% is the...

  13. Flexible Semitransparent Energy Harvester with High Pressure Sensitivity and Power Density Based on Laterally Aligned PZT Single-Crystal Nanowires.

    Science.gov (United States)

    Zhao, Quan-Liang; He, Guang-Ping; Di, Jie-Jian; Song, Wei-Li; Hou, Zhi-Ling; Tan, Pei-Pei; Wang, Da-Wei; Cao, Mao-Sheng

    2017-07-26

    A flexible semitransparent energy harvester is assembled based on laterally aligned Pb(Zr 0.52 Ti 0.48 )O 3 (PZT) single-crystal nanowires (NWs). Such a harvester presents the highest open-circuit voltage and a stable area power density of up to 10 V and 0.27 μW/cm 2 , respectively. A high pressure sensitivity of 0.14 V/kPa is obtained in the dynamic pressure sensing, much larger than the values reported in other energy harvesters based on piezoelectric single-crystal NWs. Furthermore, theoretical and finite element analyses also confirm that the piezoelectric voltage constant g 33 of PZT NWs is competitive to the lead-based bulk single crystals and ceramics, and the enhanced pressure sensitivity and power density are substantially linked to the flexible structure with laterally aligned PZT NWs. The energy harvester in this work holds great potential in flexible and transparent sensing and self-powered systems.

  14. Analysis of fruit and oil quantity and quality distribution in high-density olive trees in order to improve the mechanical harvesting process

    Energy Technology Data Exchange (ETDEWEB)

    Castillo-Ruiz, F. J.; Jiménez-Jiménez, F.; Blanco-Roldán, G.L.; Sola-Guirado, R. R.; Agüera-Vega, J.; Castro-Garcia, S.

    2015-07-01

    Olive fruit production and oil quality distribution with respect to canopy distribution are important criteria for selection and improvement of mechanical harvesting methods. Tests were performed in a high-density olive orchard (Olea europea L., cv. Arbequina) in southern Spain. Fruit distribution, fruit properties and oil parameters were measured by taken separate samples for each canopy location and tree. Results showed a high percentage of fruits and oil located in the middle-outer and upper canopy, representing more than 60% of total production. The position of these fruits along with their higher weight per fruit, maturity index and polyphenol content make them the target for all mechanical harvesting systems. The fruits from the lower canopy represented close to 30% of fruit and oil production, however, the mechanical harvesting of these fruits is inefficient for mechanical harvesting systems. Whether these fruits cannot be properly harvested, enhance tree training to raise their position is recommended. Fruits located inside the canopy are not a target location for mechanical harvesting systems as they were a small percentage of the total fruit (<10%). Significant differences were found for polyphenol content with respect to canopy height, although this was not the case with acidity. In addition, the ripening index did not influence polyphenol content and acidity values within the canopy. Fruit production, properties and oil quality varied depending on fruit canopy position. Thus harvesting systems may be targeted at maximize harvesting efficiency including an adequate tree training system adapted to the harvesting system. (Author)

  15. Analysis of fruit and oil quantity and quality distribution in high-density olive trees in order to improve the mechanical harvesting process

    Directory of Open Access Journals (Sweden)

    Francisco J. Castillo-Ruiz

    2015-06-01

    Full Text Available Olive fruit production and oil quality distribution with respect to canopy distribution are important criteria for selection and improvement of mechanical harvesting methods. Tests were performed in a high-density olive orchard (Olea europea L., cv. Arbequina in southern Spain. Fruit distribution, fruit properties and oil parameters were measured by taken separate samples for each canopy location and tree. Results showed a high percentage of fruits and oil located in the middle-outer and upper canopy, representing more than 60% of total production. The position of these fruits along with their higher weight per fruit, maturity index and polyphenol content make them the target for all mechanical harvesting systems. The fruits from the lower canopy represented close to 30% of fruit and oil production, however, the mechanical harvesting of these fruits is inefficient for mechanical harvesting systems. Whether these fruits cannot be properly harvested, enhance tree training to raise their position is recommended. Fruits located inside the canopy are not a target location for mechanical harvesting systems as they were a small percentage of the total fruit (<10%. Significant differences were found for polyphenol content with respect to canopy height, although this was not the case with acidity. In addition, the ripening index did not influence polyphenol content and acidity values within the canopy. Fruit production, properties and oil quality varied depending on fruit canopy position. Thus harvesting systems may be targeted at maximize harvesting efficiency including an adequate tree training system adapted to the harvesting system.

  16. Optimization of components in high-yield synthesis of block copolymer-mediated gold nanoparticles

    International Nuclear Information System (INIS)

    Ray, Debes; Aswal, Vinod Kumar

    2012-01-01

    The optimization to achieve stable and high-yield gold nanoparticles in block copolymer-mediated synthesis has been examined. Gold nanoparticles are synthesized using block copolymer P85 in gold salt HAuCl 4 ·3H 2 O solution. This method usually has a very limited yield which does not simply increase with the increase in the gold salt concentration. We show that the yield can be enhanced by increasing the block copolymer concentration but is limited to the factor by which the concentration is increased. On the other hand, the presence of an additional reductant (trisodium citrate) in 1:1 molar ratio with gold salt enhances the yield by manyfold. In this case (with additional reductant), the stable and high-yield nanoparticles having size about 14 nm can be synthesized at very low block copolymer concentrations. These nanoparticles thus can be efficiently used for their application such as for adsorption of proteins.

  17. Quartz crystal microbalance-based system for high-sensitivity differential sputter yield measurements

    International Nuclear Information System (INIS)

    Rubin, B.; Topper, J. L.; Farnell, C. C.; Yalin, A. P.

    2009-01-01

    We present a quartz crystal microbalance-based system for high sensitivity differential sputter yield measurements of different target materials due to ion bombardment. The differential sputter yields can be integrated to find total yields. Possible ion beam conditions include ion energies in the range of 30-350 eV and incidence angles of 0 deg. - 70 deg. from normal. A four-grid ion optics system is used to achieve a collimated ion beam at low energy (<100 eV) and a two-grid ion optics is used for higher energies (up to 750 eV). A complementary weight loss approach is also used to measure total sputter yields. Validation experiments are presented that confirm high sensitivity and accuracy of sputter yield measurements.

  18. Harvested wood products and carbon sink in a young beech high forest

    Directory of Open Access Journals (Sweden)

    Pilli R

    2008-03-01

    Full Text Available According to art. 3.4 of the Kyoto Protocol (KP, Italy has elected forest management as additional human-induced activity to attain the goal of reduction in greenhouse gas emissions. The whole forest area not subjected to afforestation, reforestation or deforestation processes since 1990 will be considered as managed forest. In order to analyse different management strategies, the Carbon-Pro Project, involving 9 partners of the European CADSES area, considered a young beech high forest (ex-coppice, defined as "transitory silvicultural system" as a common case study for the Pre-alps region. Using data collected with forest plans during the period 1983 - 2005, aboveground and belowground forest carbon stock and sink of a specific forest compartment were estimated by the Carbon Stock Method proposed by the IPCC Guidelines. In order to apply this approach 41 trees were cut and a species-specific allometric equation was developed. Considering the aboveground tree biomass, the carbon sink amounts to 1.99 and 1.84 Mg C ha-1 y-1 for the period 1983 - 1994 and 1994 - 2005 respectively. Adding the belowground tree biomass, the estimated sink amounts to 2.59 and 2.39 Mg C ha-1 y-1 for each period. Taking the harvested wood products (firewood, the total carbon sequestration during the second period is 0.16 Mg C ha-1 y-1. The case study highlights the possible rules for the different management strategies. In effect, the utilisation of the entire increase in aboveground biomass as firewood gives an energy substitution effect but, according to the Marrakesh Accords, it cannot be accounted for the KP. On the other hand, an accumulation strategy gives the maximum possible carbon absorption and retention.

  19. High field MRI in the diagnosis of multiple sclerosis: high field-high yield?

    International Nuclear Information System (INIS)

    Wattjes, Mike P.; Barkhof, Frederik

    2009-01-01

    Following the approval of the U.S. Food and Drug Administration (FDA), high field magnetic resonance imaging (MRI) has been increasingly incorporated into the clinical setting. Especially in the field of neuroimaging, the number of high field MRI applications has been increased dramatically. Taking advantage on increased signal-to-noise ratio (SNR) and chemical shift, higher magnetic field strengths offer new perspectives particularly in brain imaging and also challenges in terms of several technical and physical consequences. Over the past few years, many applications of high field MRI in patients with suspected and definite multiple sclerosis (MS) have been reported including conventional and quantitative MRI methods. Conventional pulse sequences at 3 T offers higher lesion detection rates when compared to 1.5 T, particularly in anatomic regions which are important for the diagnosis of patients with MS. MR spectroscopy at 3 T is characterized by an improved spectral resolution due to increased chemical shift allowing a better quantification of metabolites. It detects significant axonal damage already in patients presenting with clinically isolated syndromes and can quantify metabolites of special interest such as glutamate which is technically difficult to quantify at lower field strengths. Furthermore, the higher susceptibility and SNR offer advantages in the field of functional MRI and diffusion tensor imaging. The recently introduced new generation of ultra-high field systems beyond 3 T allows scanning in submillimeter resolution and gives new insights into in vivo MS pathology on MRI. The objectives of this article are to review the current knowledge and level of evidence concerning the application of high field MRI in MS and to give some ideas of research perspectives in the future. (orig.)

  20. FLEXIBLE, HIGH CHAR YIELD HYBRIDSIL ADHESIVE MATERIALS FOR NEXT GENERATION ABLATIVE THERMAL PROTECTION SYSTEMS, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — NanoSonic will create and empirically validate flexible, high char yield HybridSil adhesive nanocomposites for use within current and next generation polymer based...

  1. Improved Yield, Performance and Reliability of High-Actuator-Count Deformable Mirrors, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — The project team will conduct processing and design research aimed at improving yield, performance, and reliability of high-actuator-count micro-electro-mechanical...

  2. Creating a High-Touch Recruitment Event: Utilizing Faculty to Recruit and Yield Students

    Science.gov (United States)

    Freed, Lindsey R.; Howell, Leanne L.

    2018-01-01

    The following article describes the planning and implementation of a university student recruitment event that produced a high (new) student yield. Detailed descriptions of how staff and faculty worked together to plan and implement this event are described.

  3. Mid-Season High-Resolution Satellite Imagery for Forecasting Site-Specific Corn Yield

    Directory of Open Access Journals (Sweden)

    Nahuel R. Peralta

    2016-10-01

    Full Text Available A timely and accurate crop yield forecast is crucial to make better decisions on crop management, marketing, and storage by assessing ahead and implementing based on expected crop performance. The objective of this study was to investigate the potential of high-resolution satellite imagery data collected at mid-growing season for identification of within-field variability and to forecast corn yield at different sites within a field. A test was conducted on yield monitor data and RapidEye satellite imagery obtained for 22 cornfields located in five different counties (Clay, Dickinson, Rice, Saline, and Washington of Kansas (total of 457 ha. Three basic tests were conducted on the data: (1 spatial dependence on each of the yield and vegetation indices (VIs using Moran’s I test; (2 model selection for the relationship between imagery data and actual yield using ordinary least square regression (OLS and spatial econometric (SPL models; and (3 model validation for yield forecasting purposes. Spatial autocorrelation analysis (Moran’s I test for both yield and VIs (red edge NDVI = NDVIre, normalized difference vegetation index = NDVIr, SRre = red-edge simple ratio, near infrared = NIR and green-NDVI = NDVIG was tested positive and statistically significant for most of the fields (p < 0.05, except for one. Inclusion of spatial adjustment to model improved the model fit on most fields as compared to OLS models, with the spatial adjustment coefficient significant for half of the fields studied. When selected models were used for prediction to validate dataset, a striking similarity (RMSE = 0.02 was obtained between predicted and observed yield within a field. Yield maps could assist implementing more effective site-specific management tools and could be utilized as a proxy of yield monitor data. In summary, high-resolution satellite imagery data can be reasonably used to forecast yield via utilization of models that include spatial adjustment to

  4. Comparison of biomolecule desorption yields for low and high energy primary ions

    International Nuclear Information System (INIS)

    Kamensky, I.; Hakansson, P.; Sundqvist, B.; McNeal, C.J.; MacFarlane, R.

    1982-01-01

    Ion induced desorption yields of molecular ions from samples of cesium iodide, glycylglycine, ergosterol, bleomycin and a trinucleoside diphosphate have been studied using primary beams of 54 MeV 63 Cu 9+ and 3 keV 133 Cs + . Mass analysis was performed with a time-of-flight technique. Each sample was studied with the same spectrometer for both low and high energy primary ions and without opening of the vacuum chamber in between the measurements. The results show that fast heavy ions give larger yields for all samples studied and that the yield ratios for high to low energy desorption increase with the mass of the sample molecule. (orig.)

  5. Highly Luminescent Phase-Stable CsPbI3 Perovskite Quantum Dots Achieving Near 100% Absolute Photoluminescence Quantum Yield.

    Science.gov (United States)

    Liu, Feng; Zhang, Yaohong; Ding, Chao; Kobayashi, Syuusuke; Izuishi, Takuya; Nakazawa, Naoki; Toyoda, Taro; Ohta, Tsuyoshi; Hayase, Shuzi; Minemoto, Takashi; Yoshino, Kenji; Dai, Songyuan; Shen, Qing

    2017-10-24

    Perovskite quantum dots (QDs) as a new type of colloidal nanocrystals have gained significant attention for both fundamental research and commercial applications owing to their appealing optoelectronic properties and excellent chemical processability. For their wide range of potential applications, synthesizing colloidal QDs with high crystal quality is of crucial importance. However, like most common QD systems such as CdSe and PbS, those reported perovskite QDs still suffer from a certain density of trapping defects, giving rise to detrimental nonradiative recombination centers and thus quenching luminescence. In this paper, we show that a high room-temperature photoluminescence quantum yield of up to 100% can be obtained in CsPbI 3 perovskite QDs, signifying the achievement of almost complete elimination of the trapping defects. This is realized with our improved synthetic protocol that involves introducing organolead compound trioctylphosphine-PbI 2 (TOP-PbI 2 ) as the reactive precursor, which also leads to a significantly improved stability for the resulting CsPbI 3 QD solutions. Ultrafast kinetic analysis with time-resolved transient absorption spectroscopy evidence the negligible electron or hole-trapping pathways in our QDs, which explains such a high quantum efficiency. We expect the successful synthesis of the "ideal" perovskite QDs will exert profound influence on their applications to both QD-based light-harvesting and -emitting devices.

  6. Neglecting rice milling yield and quality underestimates economic losses from high-temperature stress.

    Directory of Open Access Journals (Sweden)

    Nathaniel B Lyman

    Full Text Available Future increases in global surface temperature threaten those worldwide who depend on rice production for their livelihoods and food security. Past analyses of high-temperature stress on rice production have focused on paddy yield and have failed to account for the detrimental impact of high temperatures on milling quality outcomes, which ultimately determine edible (marketable rice yield and market value. Using genotype specific rice yield and milling quality data on six common rice varieties from Arkansas, USA, combined with on-site, half-hourly and daily temperature observations, we show a nonlinear effect of high-temperature stress exposure on yield and milling quality. A 1 °C increase in average growing season temperature reduces paddy yield by 6.2%, total milled rice yield by 7.1% to 8.0%, head rice yield by 9.0% to 13.8%, and total milling revenue by 8.1% to 11.0%, across genotypes. Our results indicate that failure to account for changes in milling quality leads to understatement of the impacts of high temperatures on rice production outcomes. These dramatic losses result from reduced paddy yield and increased percentages of chalky and broken kernels, which together decrease the quantity and market value of milled rice. Recently published estimates show paddy yield reductions of up to 10% across the major rice-producing regions of South and Southeast Asia due to rising temperatures. The results of our study suggest that the often-cited 10% figure underestimates the economic implications of climate change for rice producers, thus potentially threatening future food security for global rice producers and consumers.

  7. High-biomass C4 grasses-Filling the yield gap.

    Science.gov (United States)

    Mullet, John E

    2017-08-01

    A significant increase in agricultural productivity will be required by 2050 to meet the needs of an expanding and rapidly developing world population, without allocating more land and water resources to agriculture, and despite slowing rates of grain yield improvement. This review examines the proposition that high-biomass C 4 grasses could help fill the yield gap. High-biomass C 4 grasses exhibit high yield due to C 4 photosynthesis, long growth duration, and efficient capture and utilization of light, water, and nutrients. These C 4 grasses exhibit high levels of drought tolerance during their long vegetative growth phase ideal for crops grown in water-limited regions of agricultural production. The stems of some high-biomass C 4 grasses can accumulate high levels of non-structural carbohydrates that could be engineered to enhance biomass yield and utility as feedstocks for animals and biofuels production. The regulatory pathway that delays flowering of high-biomass C 4 grasses in long days has been elucidated enabling production and deployment of hybrids. Crop and landscape-scale modeling predict that utilization of high-biomass C 4 grass crops on land and in regions where water resources limit grain crop yield could increase agricultural productivity. Copyright © 2017 Elsevier B.V. All rights reserved.

  8. [Effects of plastic film mulching and rain harvesting modes on chlorophyll fluorescence characteristics, yield and water use efficiency of dryland maize].

    Science.gov (United States)

    Li, Shang-Zhong; Fan, Ting-Lu; Wang, Yong; Zhao, Gang; Wang, Lei; Tang, Xiao-Ming; Dang, Yi; Zhao, Hui

    2014-02-01

    The differences on chlorophyll fluorescence parameters, yield and water use efficiency of dryland maize were compared among full plastic film mulching on double ridges and planting in catchment furrows (FFDRF), half plastic film mulching on double ridges and planting in catchment furrows (HFDRF), plastic film mulching on ridge and planting in film-side (FS), and flat planting with no plastic film mulching (NM) under field conditions in dry highland of Loess Plateau in 2007-2012. The results showed that fluorescence yield (Fo), the maximum fluorescence yield (Fm), light-adapted fluorescence yield when PS II reaction centers were totally open (F), light-adapted fluorescence yield when PS II reaction centers closed (Fm'), the maximal photochemical efficiency of PS II (Fv/Fm), the actual photochemical efficiency of PS II in the light (Phi PS II), the relative electron transport rate (ETR), photochemical quenching (qP) and non-photochemical quenching (qN) in maize leaves of FFDRF were higher than that of control (NM), and the value of 1-qP was lower than that of control, at 13:00, chlorophyll fluorescence parameters values of FFDRF was significantly higher than control, which were increased by 5.3%, 56.8%, 10.7%, 36.3%, 23.6%, 56.7%, 64.4%, 45.5%, 23.6% and -55.6%, respectively, compared with the control. Yield and water use efficiency of FFDRF were the highest in every year no matter dry year, normal year, humid year and hail disaster year. Average yield and water use efficiency of FFDRF were 12,650 kg x hm(-2) and 40.4 kg x mm(-1) x hm(-2) during 2007-2012, increased by 57.8% and 61.6% compared with the control, respectively, and also significantly higher compared with HFDRF and PS. Therefore, it was concluded that FFDRF had significantly increased the efficiency of light energy conversion and improved the production capacity of dryland maize.

  9. Effect of high oleic acid soybean on seed oil, protein concentration, and yield

    Science.gov (United States)

    Soybeans with high oleic acid content are desired by oil processors because of their improved oxidative stability for broader use in food, fuel and other products. However, non-GMO high-oleic soybeans have tended to have low seed yield. The objective of this study was to test non-GMO, high-oleic s...

  10. Stress-anneal-induced magnetic anisotropy in highly textured Fe-Ga and Fe-Al magnetostrictive strips for bending-mode vibrational energy harvesters

    Directory of Open Access Journals (Sweden)

    Jung Jin Park

    2016-05-01

    Full Text Available Magnetostrictive Fe-Ga and Fe-Al alloys are promising materials for use in bending-mode vibrational energy harvesters. For this study, 50.8 mm × 5.0 mm × 0.5 mm strips of Fe-Ga and Fe-Al were cut from 0.50-mm thick rolled sheet. An atmospheric anneal was used to develop a Goss texture through an abnormal grain growth process. The anneal lead to large (011 grains that covered over 90% of sample surface area. The resulting highly-textured Fe-Ga and Fe-Al strips exhibited saturation magnetostriction values (λsat =  λ∥ − λ⊥ of ∼280 ppm and ∼130 ppm, respectively. To maximize 90° rotation of magnetic moments during bending of the strips, we employed compressive stress annealing (SA. Samples were heated to 500°C, and a 100-150 MPa compressive stress was applied while at 500°C for 30 minutes and while being cooled. The effectiveness of the SA on magnetic moment rotation was inferred by comparing post-SA magnetostriction with the maximum possible yield of rotated magnetic moments, which is achieved when λ∥ = λsat and λ⊥ = 0. The uniformity of the SA along the sample length and the impact of the SA on sensing/energy harvesting performance were then assessed by comparing pre- and post-SA bending-stress-induced changes in magnetization at five different locations along the samples. The SA process with a 150 MPa compressive load improved Fe-Ga actuation along the sample length from 170 to 225 ppm (from ∼60% to within ∼80% of λsat. The corresponding sensing/energy harvesting performance improved by as much as a factor of eight in the best sample, however the improvement was not at all uniform along the sample length. The SA process with a 100 MPa compressive load improved Fe-Al actuation along the sample length from 60 to 73 ppm (from ∼46% to ∼56% of λsat, indicating only a marginally effective SA and suggesting the need for modification of the SA protocol. In spite of this, the SA was effective at improving the sensing

  11. Stress-anneal-induced magnetic anisotropy in highly textured Fe-Ga and Fe-Al magnetostrictive strips for bending-mode vibrational energy harvesters

    Science.gov (United States)

    Park, Jung Jin; Na, Suok-Min; Raghunath, Ganesh; Flatau, Alison B.

    2016-05-01

    Magnetostrictive Fe-Ga and Fe-Al alloys are promising materials for use in bending-mode vibrational energy harvesters. For this study, 50.8 mm × 5.0 mm × 0.5 mm strips of Fe-Ga and Fe-Al were cut from 0.50-mm thick rolled sheet. An atmospheric anneal was used to develop a Goss texture through an abnormal grain growth process. The anneal lead to large (011) grains that covered over 90% of sample surface area. The resulting highly-textured Fe-Ga and Fe-Al strips exhibited saturation magnetostriction values (λsat = λ∥ - λ⊥) of ˜280 ppm and ˜130 ppm, respectively. To maximize 90° rotation of magnetic moments during bending of the strips, we employed compressive stress annealing (SA). Samples were heated to 500°C, and a 100-150 MPa compressive stress was applied while at 500°C for 30 minutes and while being cooled. The effectiveness of the SA on magnetic moment rotation was inferred by comparing post-SA magnetostriction with the maximum possible yield of rotated magnetic moments, which is achieved when λ∥ = λsat and λ⊥ = 0. The uniformity of the SA along the sample length and the impact of the SA on sensing/energy harvesting performance were then assessed by comparing pre- and post-SA bending-stress-induced changes in magnetization at five different locations along the samples. The SA process with a 150 MPa compressive load improved Fe-Ga actuation along the sample length from 170 to 225 ppm (from ˜60% to within ˜80% of λsat). The corresponding sensing/energy harvesting performance improved by as much as a factor of eight in the best sample, however the improvement was not at all uniform along the sample length. The SA process with a 100 MPa compressive load improved Fe-Al actuation along the sample length from 60 to 73 ppm (from ˜46% to ˜56% of λsat, indicating only a marginally effective SA and suggesting the need for modification of the SA protocol. In spite of this, the SA was effective at improving the sensing/energy harvesting

  12. Extracting DNA from 'jaws': High yield and quality from archived tiger shark (Galeocerdo cuvier) skeletal material

    DEFF Research Database (Denmark)

    Eg Nielsen, Einar; Morgan, J. A T; Maher, S. L.

    2017-01-01

    of tiger sharks (Galeocerdo cuvier). Protocols were compared for DNA yield and quality using a qPCR approach. For jaw swarf, all methods provided relatively high DNA yield and quality, while large differences in yield between protocols were observed for vertebrae. Similar results were obtained from samples...... observed, likely reflecting different preparation and storage methods for the trophies. Trial sequencing of DNA capture genomic libraries using 20 000 baits revealed that a significant proportion of captured sequences were derived from tiger sharks. This study demonstrates that archived shark jaws...

  13. Development of high yielding Soybean variety MACS 450 by using Kalitur mutant-MACS 111

    International Nuclear Information System (INIS)

    Raut, V.M.; Taware, S.P.; Halvankar, G.B.; Varghese, Philips

    2000-01-01

    A mutant variety -MACS 111 developed by treating seeds of indigenous black seeded 'Kalitur' variety with gamma irradiation + Ethyleneimine was used in development of high yielding varieties. MACS 450 a promising high yielding variety was selected from Bragg x MACS 111 cross by pedigree selection method. This variety gave the highest average seed yield in station trials (3422 kg/ha), coordinated breeding trials (2361 kg/ha) and varieties cum plant population trial (2215 kg/ha). On the basis of its performance in these trials it was released for commercial cultivation in Southern India. On all India basis, it also recorded the highest seed yield of 4076 kg/ha and 3582 kg/ha in Front line Demonstrations conducted on the farmers' field during 1998 and 1999 respectively. (author)

  14. High pressure near infrared study of the mutated light-harvesting complex LH2

    Directory of Open Access Journals (Sweden)

    Braun P.

    2005-01-01

    Full Text Available The pressure sensitivities of the near infrared spectra of the light-harvesting (LH2 complex and a mutant complex with a simplified BChl-B850 binding pocket were compared. In the mutant an abrupt change in the spectral properties occurred at 250 MPa, which was not observed with the native sample. Increased disorder due to collapse of the chromophore pocket is suggested.

  15. HIGH YIELD GENETICALLY MODIFIED WHEAT IN GERMANY: SOCIO ECONOMIC ASSESSMENT OF ITS POTENTIAL

    OpenAIRE

    Wree, Philipp; Sauer, Johannes

    2015-01-01

    High Yield Genetically Modified Wheat (HOSUT) HOSUT lines are an innovation in wheat breeding based on biotechnology with an incremental yield potential of ca. 28% compared to conventional wheat varieties. We apply the real option concept of Maximum Incremental Social Tolerable Irreversible Costs (MISTICs) to do an ex-ante assessment of the socioeconomic potential of HOSUT lines for Germany. We analyze the cost and benefits to farmer and society within two scenarios. Our results of our scenar...

  16. Nitrogen detected TROSY at high field yields high resolution and sensitivity for protein NMR

    International Nuclear Information System (INIS)

    Takeuchi, Koh; Arthanari, Haribabu; Shimada, Ichio; Wagner, Gerhard

    2015-01-01

    Detection of 15 N in multidimensional NMR experiments of proteins has sparsely been utilized because of the low gyromagnetic ratio (γ) of nitrogen and the presumed low sensitivity of such experiments. Here we show that selecting the TROSY components of proton-attached 15 N nuclei (TROSY 15 N H ) yields high quality spectra in high field magnets (>600 MHz) by taking advantage of the slow 15 N transverse relaxation and compensating for the inherently low 15 N sensitivity. The 15 N TROSY transverse relaxation rates increase modestly with molecular weight but the TROSY gain in peak heights depends strongly on the magnetic field strength. Theoretical simulations predict that the narrowest line width for the TROSY 15 N H component can be obtained at 900 MHz, but sensitivity reaches its maximum around 1.2 GHz. Based on these considerations, a 15 N-detected 2D 1 H– 15 N TROSY-HSQC ( 15 N-detected TROSY-HSQC) experiment was developed and high-quality 2D spectra were recorded at 800 MHz in 2 h for 1 mM maltose-binding protein at 278 K (τ c  ∼ 40 ns). Unlike for 1 H detected TROSY, deuteration is not mandatory to benefit 15 N detected TROSY due to reduced dipolar broadening, which facilitates studies of proteins that cannot be deuterated, especially in cases where production requires eukaryotic expression systems. The option of recording 15 N TROSY of proteins expressed in H 2 O media also alleviates the problem of incomplete amide proton back exchange, which often hampers the detection of amide groups in the core of large molecular weight proteins that are expressed in D 2 O culture media and cannot be refolded for amide back exchange. These results illustrate the potential of 15 N H -detected TROSY experiments as a means to exploit the high resolution offered by high field magnets near and above 1 GHz

  17. [Construction and high-density fermentation of alkaline pectate lyase high-yield yeast].

    Science.gov (United States)

    Wang, Xiaowen; Xiang, La; Xu, Ting; Lu, Zhenghui; Zhang, Guimin

    2017-12-25

    Pectate lyase is widely applied in ramie degumming and fabric bioscouring in the textile industry. Compared to conventional processes that involve high alkaline and high temperature treatment, enzyme based treatments have significant advantages in fibers protectiveness, improved efficiency of refining, reduced energy consumption and pollution. Hence, it would be highly desirable to construct high-yield alkaline pectate lyase engineered strains and reduce the pectate lyase production cost. In the previous study, pectate lyase gene pel from Bacillus subtilis168 was expressed in Pichia pastoris GS115 after codon usage optimization based on the vector pHBM905A. To improve the expression level, the vector pHBM905BDM with optimized promoter and signal peptide was used to express the optimized gene pels in GS115. The transformant had increased activity from 68 U/mL to 100 U/mL with the improvement in the transcription level by 27% measured by qPCR. The transformants were further screened on pectin plates, where higher halo forming strains were picked for shake-flask fermentation and strain GS115-pHBM905BDM-pels4 showed the highest activity of 536 U/mL. Then plasmid pPIC9K-pels was constructed and electroporated into the GS115-pHBM905BDM-pels4 cells. Subsequently, high-copy transformant was screened by using the medium containing antibiotics G418, strain GS115-pHBM905BDMpPIC9K- pels1 was identified with increased activity of 770 U/mL and the copy number of pels was 7 confirmed by qPCR. Finally, the activity of pectate lyase produced by GS115-pHBM905BDM-pPIC9K-pels1reached to 2 271 U/mL in a 5-L fermentor. The activity of pectate lyase in our study reached the highest level of expression in P. pastoris, showing good application potential in the textile industry.

  18. Nitrogen detected TROSY at high field yields high resolution and sensitivity for protein NMR

    Energy Technology Data Exchange (ETDEWEB)

    Takeuchi, Koh [National Institute for Advanced Industrial Science and Technology, Molecular Profiling Research Center for Drug Discovery (Japan); Arthanari, Haribabu [Harvard Medical School, Department of Biochemistry and Molecular Pharmacology (United States); Shimada, Ichio, E-mail: shimada@iw-nmr.f.u-tokyo.ac.jp [National Institute for Advanced Industrial Science and Technology, Molecular Profiling Research Center for Drug Discovery (Japan); Wagner, Gerhard, E-mail: gerhard-wagner@hms.harvard.edu [Harvard Medical School, Department of Biochemistry and Molecular Pharmacology (United States)

    2015-12-15

    Detection of {sup 15}N in multidimensional NMR experiments of proteins has sparsely been utilized because of the low gyromagnetic ratio (γ) of nitrogen and the presumed low sensitivity of such experiments. Here we show that selecting the TROSY components of proton-attached {sup 15}N nuclei (TROSY {sup 15}N{sub H}) yields high quality spectra in high field magnets (>600 MHz) by taking advantage of the slow {sup 15}N transverse relaxation and compensating for the inherently low {sup 15}N sensitivity. The {sup 15}N TROSY transverse relaxation rates increase modestly with molecular weight but the TROSY gain in peak heights depends strongly on the magnetic field strength. Theoretical simulations predict that the narrowest line width for the TROSY {sup 15}N{sub H} component can be obtained at 900 MHz, but sensitivity reaches its maximum around 1.2 GHz. Based on these considerations, a {sup 15}N-detected 2D {sup 1}H–{sup 15}N TROSY-HSQC ({sup 15}N-detected TROSY-HSQC) experiment was developed and high-quality 2D spectra were recorded at 800 MHz in 2 h for 1 mM maltose-binding protein at 278 K (τ{sub c} ∼ 40 ns). Unlike for {sup 1}H detected TROSY, deuteration is not mandatory to benefit {sup 15}N detected TROSY due to reduced dipolar broadening, which facilitates studies of proteins that cannot be deuterated, especially in cases where production requires eukaryotic expression systems. The option of recording {sup 15}N TROSY of proteins expressed in H{sub 2}O media also alleviates the problem of incomplete amide proton back exchange, which often hampers the detection of amide groups in the core of large molecular weight proteins that are expressed in D{sub 2}O culture media and cannot be refolded for amide back exchange. These results illustrate the potential of {sup 15}N{sub H}-detected TROSY experiments as a means to exploit the high resolution offered by high field magnets near and above 1 GHz.

  19. Optimization Design of an Inductive Energy Harvesting Device for Wireless Power Supply System Overhead High-Voltage Power Lines

    Directory of Open Access Journals (Sweden)

    Wei Wang

    2016-03-01

    Full Text Available Overhead high voltage power line (HVPL online monitoring equipment is playing an increasingly important role in smart grids, but the power supply is an obstacle to such systems’ stable and safe operation, so in this work a hybrid wireless power supply system, integrated with inductive energy harvesting and wireless power transmitting, is proposed. The energy harvesting device extracts energy from the HVPL and transfers that from the power line to monitoring equipment on transmission towers by transmitting and receiving coils, which are in a magnetically coupled resonant configuration. In this paper, the optimization design of online energy harvesting devices is analyzed emphatically by taking both HVPL insulation distance and wireless power supply efficiency into account. It is found that essential parameters contributing to more extracted energy include large core inner radius, core radial thickness, core height and small core gap within the threshold constraints. In addition, there is an optimal secondary coil turn that can maximize extracted energy when other parameters remain fixed. A simple and flexible control strategy is then introduced to limit power fluctuations caused by current variations. The optimization methods are finally verified experimentally.

  20. Vibro-Shock Dynamics Analysis of a Tandem Low Frequency Resonator—High Frequency Piezoelectric Energy Harvester

    Directory of Open Access Journals (Sweden)

    Darius Žižys

    2017-04-01

    Full Text Available Frequency up-conversion is a promising technique for energy harvesting in low frequency environments. In this approach, abundantly available environmental motion energy is absorbed by a Low Frequency Resonator (LFR which transfers it to a high frequency Piezoelectric Vibration Energy Harvester (PVEH via impact or magnetic coupling. As a result, a decaying alternating output signal is produced, that can later be collected using a battery or be transferred directly to the electric load. The paper reports an impact-coupled frequency up-converting tandem setup with different LFR to PVEH natural frequency ratios and varying contact point location along the length of the harvester. RMS power output of different frequency up-converting tandems with optimal resistive values was found from the transient analysis revealing a strong relation between power output and LFR-PVEH natural frequency ratio as well as impact point location. Simulations revealed that higher power output is obtained from a higher natural frequency ratio between LFR and PVEH, an increase of power output by one order of magnitude for a doubled natural frequency ratio and up to 150% difference in power output from different impact point locations. The theoretical results were experimentally verified.

  1. A utility piezoelectric energy harvester with low frequency and high-output voltage: Theoretical model, experimental verification and energy storage

    Directory of Open Access Journals (Sweden)

    Guangyi Zhang

    2016-09-01

    Full Text Available In this paper, a utility piezoelectric energy harvester with low frequency and high-output voltage is presented. Firstly, the harvester’s three theoretical models are presented, namely the static model, the quasi static model and the dynamic vibration model. By analyzing the influence of the mass ratio of the mass block to the beam on output characteristics of the harvester, we compare the quasi static model and the dynamic vibration model and then define their applicable ranges. Secondly, simulation and experiments are done to verify the models, using the harvester with PZT-5H piezoelectric material, which are proved to be consistent with each other. The experimental results show that the output open-circuit voltage and the output power can reach up to 86.36V and 27.5mW respectively. The experiments are conducted when this harvester system is excited by the first modal frequency (58.90Hz with the acceleration 10m/s2. In this low frequency vibration case, it is easy to capture the energy in the daily environment. In addition, LTC 3588-1 chip (Linear Technology Corporation is used as the medium energy circuit to transfer charges from the PZT-5H electrode to the 0.22F 5V super capacitor and ML621 rechargeable button battery. For this super-capacitor, it takes about 100min for the capacitor voltage to rise from 0V to 3.6V. For this button battery, it takes about 200min to increase the battery voltage from 2.5V to 3.48V.

  2. Effect of Different Levels of Organic and Chemical Fertilizers on Yield, Harvest Index and Extract Percentage of Hemp (Cannabis sativa L.

    Directory of Open Access Journals (Sweden)

    S Laleh

    2018-02-01

    Full Text Available Introduction Hemp is a dioecious and annual plant. The most important use to this plant is in the food, drug, and natural fibers. Proper fertilizer management for a medicinal plant species is important for increasing its yield and maintaining the quality of active principles. Sustainable farming is on the basis of natural fertilizer application with the aim of decreasing chemical fertilizers. Various studies show that application of animal manure with chemical fertilizers (as N, P and … have positive effects on soil structure, microbial population, soil fertility, growth and yield of plant with the aim of protecting the environment. Therefore, the present study was under taken to evaluate the effect of organic amendments enriched with chemical fertilizers of nitrogen and phosphorus on yield and extract of hemp. Materials and Methods To study the effect of different levels of animal manure and chemical fertilizers, a split factorial experiment, based on complete randomized blocks design with three replications was conducted at the research Farm of Faculty of agriculture, University of Birjand, during the growing season 2014-2015. Experimental factors were animal manure (0, 10, 20 and 30 t. ha-1well rotted farmyard manure as the main plot, and factorial application of three levels of N (0, 50 and 100 kg N ha-1 as Urea with two levels of P (0 and 80 kg P2O5 ha-1 as triple and P was superphosphate as sub-plot. Animal manure, P and half of the N fertilizer were applied before planting and the other half of N were applied by top dressing. Hemp were planted 5 may on rows 60 cm apart, with 30 cm distance between each hemp on row, at the depth of 3-4 cm. Measured traits included leaf, stem and seed weights, stem height and diameter, 1000 seed weight, and leaves extract percentage per square meter in sub-plot for female plants of hemp. Also percentage of female plants calculated per sub-plot. Finally, all variables were analyzed by SAS software (V. 9

  3. Mutation breeding of Bacillus subtilis YTB4 with high yield of ...

    African Journals Online (AJOL)

    DR TONUKARI NYEROVWO

    2012-07-17

    Jul 17, 2012 ... Helium-neon (He-Ne) laser irradiation is a highly efficient mutation breeding technology and is widely applied to various fields of biological science. Using Bacillus subtilis YTB4 with high yield of multienzyme complex as original strain, mutation breeding was carried out by He-Ne laser irradiation in.

  4. Mutation breeding of Bacillus subtilis YTB4 with high yield of ...

    African Journals Online (AJOL)

    Helium-neon (He-Ne) laser irradiation is a highly efficient mutation breeding technology and is widely applied to various fields of biological science. Using Bacillus subtilis YTB4 with high yield of multienzyme complex as original strain, mutation breeding was carried out by He-Ne laser irradiation in this study. Based on the ...

  5. Sputtering yields of carbon based materials under high particle flux with low energy

    Science.gov (United States)

    Nakamura, K.; Nagase, A.; Dairaku, M.; Akiba, M.; Araki, M.; Okumura, Y.

    1995-04-01

    A new ion source which can produce high particle flux beams at low energies has been developed. This paper presents preliminary results on the sputtering yield of the carbon fiber reinforced composites (CFCs) measured with the new ion source. The sputtering yields of 1D and 2D CFCs, which are candidate materials for the divertor armour tiles, have been measured by the weight loss method under the hydrogen and deuterium particle fluxes of 2 ˜ 7 × 10 20/m 2 s at 50 ˜ 150 eV. Preferential sputtering of the matrix was observed on CFCs which included the matrix of 40 ˜ 60 w%. The energy dependence of the sputtering yields was weak. The sputtering yields of CFCs normally irradiated with deuterium beam were from 0.073 to 0.095, and were around three times larger than those with hydrogen beam.

  6. Sputtering yields of carbon based materials under high particle flux with low energy

    International Nuclear Information System (INIS)

    Nakamura, K.; Nagase, A.; Dairaku, M.; Akiba, M.; Araki, M.; Okumura, Y.

    1995-01-01

    A new ion source which can produce high particle flux beams at low energies has been developed. This paper presents preliminary results on the sputtering yield of the carbon fiber reinforced composites (CFCs) measured with the new ion source. The sputtering yields of 1D and 2D CFCs, which are candidate materials for the divertor armour tiles, have been measured by the weight loss method under the hydrogen and deuterium particle fluxes of 2 similar 7x10 20 /m 2 s at 50 similar 150 eV. Preferential sputtering of the matrix was observed on CFCs which included the matrix of 40 similar 60 w%. The energy dependence of the sputtering yields was weak. The sputtering yields of CFCs normally irradiated with deuterium beam were from 0.073 to 0.095, and were around three times larger than those with hydrogen beam. ((orig.))

  7. Creating high yield water soluble luminescent graphene quantum dots via exfoliating and disintegrating carbon nanotubes and graphite flakes.

    Science.gov (United States)

    Lin, Liangxu; Zhang, Shaowei

    2012-10-21

    We have developed an effective method to exfoliate and disintegrate multi-walled carbon nanotubes and graphite flakes. With this technique, high yield production of luminescent graphene quantum dots with high quantum yield and low oxidization can be achieved.

  8. Reduced use of allogeneic platelets through high-yield perioperative autologous plateletpheresis and reinfusion.

    Science.gov (United States)

    Alberts, Melissa; Bandarenko, Nicholas; Gaca, Jeffrey; Lockhart, Evelyn; Milano, Carmelo; Alexander, Stanlin; Linder, Dean; Lombard, Frederick W; Welsby, Ian J

    2014-05-01

    Intraoperative autologous platelet (PLT) collection as part of a multimodal blood conservation program carries a Class IIa recommendation from the Societies of Thoracic Surgeons and Cardiovascular Anesthesiologists, but achieving a suitable PLT yield limits its application. A novel, autologous, intraoperative, high-yield plateletpheresis collection program was established and retrospectively analyzed to identify potential improvements over previously reported plateletpheresis protocols. Targeting complex cardiothoracic surgery patients without recent anti-PLT agents, thrombocytopenia, or severe anemia, the program aimed to achieve a PLT yield of at least one standard apheresis unit (3.0 × 10(11) ) within 60 to 90 minutes and using an automated plateletpheresis device (Trima, Terumo BCT). Anesthetized and invasively monitored patients underwent plateletpheresis via a large-bore, indwelling central line placed for the surgery. Collection-related data for quality control purposes and subsequent PLT transfusion requirements were analyzed and reported. Forty-two patients donated autologous PLTs between 2011 and 2012. PLT yield was 4.5 (3.9-5.0) × 10(11) , which significantly exceeds previously reported yields, and procedure duration was 53.2 (48.4-57.9) minutes. As anticipated, postcollection PLT count decreased from 268 (242-293) × 10(9) to 182 (163-201) × 10(9) /L; hypocalcemia was minimized by infusion of 1 g of CaCl2 . Autologous PLT yield was inversely correlated with allogeneic PLT use, and avoidance of allogeneic PLT transfusion was increased when the autologous yield was the equivalent of 2 or more apheresis units. High-yield, intraoperative autologous PLT collection is achievable using an automated plateletpheresis device. Initial experience shows a reduction in reliance on allogeneic PLTs for complex cardiothoracic surgery. © 2013 American Association of Blood Banks.

  9. High-performance piezoelectric thick film based energy harvesting micro-generators for MEMS

    DEFF Research Database (Denmark)

    Zawada, Tomasz; Hansen, Karsten; Lou-Moeller, Rasmus

    2010-01-01

    and are transformed by the energy harvesting micro-generator into usable electrical signal. The micro-generator comprises a silicon cantilever with integrated InSensor® TF2100 PZT thick film deposited using screen-printing. The output power versus frequency and electrical load has been investigated. Furthermore......, devices based on modified, pressure treated thick film materials have been tested and compared with the commercial InSensor® TF2100 PZT thick films. It has been found that the structures based on the pressure treated materials exhibit superior properties in terms of energy output....

  10. Evaluation of Over-The-Row Harvester Damage in a Super-High-Density Olive Orchard Using On-Board Sensing Techniques

    Directory of Open Access Journals (Sweden)

    Manuel Pérez-Ruiz

    2018-04-01

    Full Text Available New super-high-density (SHD olive orchards designed for mechanical harvesting using over-the-row harvesters are becoming increasingly common around the world. Some studies regarding olive SHD harvesting have focused on the effective removal of the olive fruits; however, the energy applied to the canopy by the harvesting machine that can result in fruit damage, structural damage or extra stress on the trees has been little studied. Using conventional analyses, this study investigates the effects of different nominal speeds and beating frequencies on the removal efficiency and the potential for fruit damage, and it uses remote sensing to determine changes in the plant structures of two varieties of olive trees (‘Manzanilla Cacereña’ and ‘Manzanilla de Sevilla’ planted in SHD orchards harvested by an over-the-row harvester. ‘Manzanilla de Sevilla’ fruit was the least tolerant to damage, and for this variety, harvesting at the highest nominal speed led to the greatest percentage of fruits with cuts. Different vibration patterns were applied to the olive trees and were evaluated using triaxial accelerometers. The use of two light detection and ranging (LiDAR sensing devices allowed us to evaluate structural changes in the studied olive trees. Before- and after-harvest measurements revealed significant differences in the LiDAR data analysis, particularly at the highest nominal speed. The results of this work show that the operating conditions of the harvester are key to minimising fruit damage and that a rapid estimate of the damage produced by an over-the-row harvester with contactless sensing could provide useful information for automatically adjusting the machine parameters in individual olive groves in the future.

  11. Multiyear high-resolution carbon exchange over European croplands from the integration of observed crop yields into CarbonTracker Europe

    Science.gov (United States)

    Combe, Marie; Vilà-Guerau de Arellano, Jordi; de Wit, Allard; Peters, Wouter

    2016-04-01

    Carbon exchange over croplands plays an important role in the European carbon cycle over daily-to-seasonal time scales. Not only do crops occupy one fourth of the European land area, but their photosynthesis and respiration are large and affect CO2 mole fractions at nearly every atmospheric CO2 monitoring site. A better description of this crop carbon exchange in our CarbonTracker Europe data assimilation system - which currently treats crops as unmanaged grasslands - could strongly improve its ability to constrain terrestrial carbon fluxes. Available long-term observations of crop yield, harvest, and cultivated area allow such improvements, when combined with the new crop-modeling framework we present. This framework can model the carbon fluxes of 10 major European crops at high spatial and temporal resolution, on a 12x12 km grid and 3-hourly time-step. The development of this framework is threefold: firstly, we optimize crop growth using the process-based WOrld FOod STudies (WOFOST) agricultural crop growth model. Simulated yields are downscaled to match regional crop yield observations from the Statistical Office of the European Union (EUROSTAT) by estimating a yearly regional parameter for each crop species: the yield gap factor. This step allows us to better represent crop phenology, to reproduce the observed multiannual European crop yields, and to construct realistic time series of the crop carbon fluxes (gross primary production, GPP, and autotrophic respiration, Raut) on a fine spatial and temporal resolution. Secondly, we combine these GPP and Raut fluxes with a simple soil respiration model to obtain the total ecosystem respiration (TER) and net ecosystem exchange (NEE). And thirdly, we represent the horizontal transport of carbon that follows crop harvest and its back-respiration into the atmosphere during harvest consumption. We distribute this carbon using observations of the density of human and ruminant populations from EUROSTAT. We assess the model

  12. High-Yield Synthesis of Zinc Oxide Nanoparticles from Bicontinuous Microemulsions

    Directory of Open Access Journals (Sweden)

    S. López-Cuenca

    2011-01-01

    Full Text Available The high-yield synthesis of zinc oxide (ZnO primary nanoparticles with high purity and with diameters between 6 and 22 nm using bicontinuous microemulsions is reported in this work. The ZnO nanoparticles were made by hydrolysis of Zn(NO32 with NaOH aqueous solution and precipitation, followed by calcination of the precipitate. Higher yields and productivities of ZnO nanoparticles were obtained compared to values produced with w/o micremulsions reported in the literature. Particles were characterized by transmission electronic microscopy (TEM, X-ray diffraction, and atomic absorption spectroscopy.

  13. Mass production of multi-wall carbon nanotubes by metal dusting process with high yield

    Energy Technology Data Exchange (ETDEWEB)

    Ghorbani, H. [School of Metallurgy and Materials Engineering, Iran University of Science and Technology, Narmak, Tehran (Iran, Islamic Republic of); Rashidi, A.M., E-mail: Rashidiam@ripi.ir [Nanotechnology Research Center, Research Institute of Petroleum Industry (RIPI), West Blvd. Azadi Sport Complex, P.O. Box 14665-1998, Tehran (Iran, Islamic Republic of); Rastegari, S.; Mirdamadi, S. [School of Metallurgy and Materials Engineering, Iran University of Science and Technology, Narmak, Tehran (Iran, Islamic Republic of); Alaei, M. [Nanotechnology Research Center, Research Institute of Petroleum Industry (RIPI), West Blvd. Azadi Sport Complex, P.O. Box 14665-1998, Tehran (Iran, Islamic Republic of)

    2011-05-15

    Research highlights: {yields} Synthesis of carbon nanotubes over Fe-Ni nanoparticles supported alloy 304L. {yields} Production of carbon nanotubes with high yield (700-1000%) and low cost catalyst. {yields} Optimum growth condition is CO/H{sub 2} = 1/1, 100 cm{sup 3}/min, at 620 {sup o}C under long term repetitive thermal cycling. {yields} Possibility of the mass production by metal dusting process with low cost. -- Abstract: Carbon nanotube materials were synthesized over Fe-Ni nanoparticles generated during disintegration of the surface of alloy 304L under metal dusting environment. The metal dusting condition was simulated and optimized through exposing stainless steel samples during long term repetitive thermal cycling in CO/H{sub 2} = 1/1, total gas flow rate 100 cm{sup 3}/min, at 620 {sup o}C for 300 h. After reaction, surface morphology of the samples and also carbonaceous deposition which had grown on sample surfaces were examined by stereoscopy, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Results revealed that multi-wall carbon nanotubes could be formed over nanocatalyst generated on the alloy surface by exploiting metal dusting process. By optimization of reaction parameters the yields of carbon nanotube materials obtained were 700-1000%. Also it has been shown herein that the amount of carbon nanotube materials remarkably increases when the reaction time is extended up to 300 h, indicating a possibility of the mass production by this easy method.

  14. Thermoelectric Energy Harvesting Using Phase Change Materials (PCMs) in High Temperature Environments in Aircraft

    Science.gov (United States)

    Elefsiniotis, A.; Becker, Th.; Schmid, U.

    2014-06-01

    Wireless, energy-autonomous structural health-monitoring systems in aircraft have the potential of reducing total maintenance costs. Thermoelectric energy harvesting, which seems the best choice for creating truly autonomous health monitoring sensors, is the principle behind converting waste heat to useful electrical energy through the use of thermoelectric generators. To enhance the temperature difference across the two sides of a thermoelectric generator, i.e. increasing heat flux and energy production, a phase change material acting as thermal mass is attached on one side of the thermoelectric generators while the other side is placed on the aircraft structure. The application area under investigation for this paper is the pylon aft fairing, located near the engine of an aircraft, with temperatures reaching on the inside up to 350 °C. Given these harsh operational conditions, the performance of a device, containing erythritol as a phase change material, is evaluated. The harvested energy reaching values up to 81.4 J can be regulated by a power management module capable of storing the excess energy and recovering it from the medium powering a sensor node and a wireless transceiver.

  15. Yield Mapping in Salix; Skoerdekartering av salix

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, Christoffer; Gilbertsson, Mikael; Rogstrand, Gustav; Thylen, Lars

    2004-09-01

    The most common species for energy forest production is willow. Willow is able to produce a large amount of biomass in a short period of time. Growing willow has a potential to render a good financial result for the farmer if cultivated on fields with the right conditions and plenty of water. Under the right conditions growing willow can give the farmer a net income of 3,000 SEK (about 430 USD) per hectare and year, which is something that common cereal crops cannot compete with. However, this is not the common case since willow is often grown as a substitute crop on fields where cereal crop yield is low. The aim of this study was to reveal if it is possible to measure yield variability in willow, and if it is possible to describe the reasons for yield variation both within the field but also between different fields. Yield mapping has been used in conventional farming for about a decade. The principles for yield mapping are to continuously measure the yield while registering location by the use of GPS when harvesting the field. The collected data is then used to search for spatial variations within the field, and to try to understand the reasons for this variation. Since there is currently no commercial equipment for yield mapping in willow, a yield mapping system had to be developed within this project. The new system was installed on a Claas Jaguar harvester. The principle for yield mapping on the Claas Jaguar harvester is to measure the distance between the feeding rollers. This distance is correlated to the flow through the harvester. The speed and position of the machine was registered using GPS. Knowing the working width of the harvester this information was used to calculate the yield. All collected data was stored on a PDA computer. Soil samples were also collected from the yield mapped fields. This was to be able to test yield against both physical and chemical soil parameters. The result shows that it is possible to measure spatial variations of yield in

  16. High-resolution, regional-scale crop yield simulations for the Southwestern United States

    Science.gov (United States)

    Stack, D. H.; Kafatos, M.; Medvigy, D.; El-Askary, H. M.; Hatzopoulos, N.; Kim, J.; Kim, S.; Prasad, A. K.; Tremback, C.; Walko, R. L.; Asrar, G. R.

    2012-12-01

    Over the past few decades, there have been many process-based crop models developed with the goal of better understanding the impacts of climate, soils, and management decisions on crop yields. These models simulate the growth and development of crops in response to environmental drivers. Traditionally, process-based crop models have been run at the individual farm level for yield optimization and management scenario testing. Few previous studies have used these models over broader geographic regions, largely due to the lack of gridded high-resolution meteorological and soil datasets required as inputs for these data intensive process-based models. In particular, assessment of regional-scale yield variability due to climate change requires high-resolution, regional-scale, climate projections, and such projections have been unavailable until recently. The goal of this study was to create a framework for extending the Agricultural Production Systems sIMulator (APSIM) crop model for use at regional scales and analyze spatial and temporal yield changes in the Southwestern United States (CA, AZ, and NV). Using the scripting language Python, an automated pipeline was developed to link Regional Climate Model (RCM) output with the APSIM crop model, thus creating a one-way nested modeling framework. This framework was used to combine climate, soil, land use, and agricultural management datasets in order to better understand the relationship between climate variability and crop yield at the regional-scale. Three different RCMs were used to drive APSIM: OLAM, RAMS, and WRF. Preliminary results suggest that, depending on the model inputs, there is some variability between simulated RCM driven maize yields and historical yields obtained from the United States Department of Agriculture (USDA). Furthermore, these simulations showed strong non-linear correlations between yield and meteorological drivers, with critical threshold values for some of the inputs (e.g. minimum and

  17. Climate Change Impacts on Sediment Yield in Headwaters of a High-latitude Region in China

    Science.gov (United States)

    Zhou, Y.; Xu, Y. J.; Wang, J., , Dr; Weihua, X.; Huang, Y.

    2017-12-01

    Climate change is expected to have strongest effects in higher latitude regions. Despite intensive research on possible hydrological responses to global warming in these regions, our knowledge of climate change on surface erosion and sediment yield in high-latitude headwaters is limited. In this study, we used the Soil and Water Assessment Tool (SWAT) to predict future runoff and sediment yield from the headwaters of a high-latitude river basin in China's far northeast. The SWAT model was first calibrated with historical discharge records and the model parameterization achieved satisfactory validation. The calibrated model was then applied to two greenhouse gas concentration trajectories, RCP4.5 and RCP8.5, for the period from 2020 to 2050 to estimate future runoff. Sediment yields for this period were predicted using a discharge-sediment load rating curve developed from field measurements in the past nine years. Our preliminary results show an increasing trend of sediment yield under both climate change scenarios, and that the increase is more pronounced in the summer and autumn months. Changes in precipitation and temperature seem to exert variable impacts on runoff and sediment yield at interannual and seasonal scales in these headwaters. These findings imply that the current river basin management in the region needs to be reviewed and improved in order to be effective under a changing climate.

  18. Development of high yield strength non-magnetic steels for the equipments of nuclear fusion research

    International Nuclear Information System (INIS)

    Matsuoka, Hidenori; Mukai, Tetsuya; Ohtani, Hiroo; Tsuruki, Takanori; Okada, Yasutaka

    1979-01-01

    Recently, activity of nuclear fusion research and so forth increase the demand of non-magnetic materials for various equipments and structures. For these usage, very low magnetic permeability as well as high strength are required under high magnetic field. Based on fundamental research, middle C-17% Cr-7% Ni-N non-magnetic steel has been developed. The developed steel shows more stable austenite phase and possesses higher yield strength and endurance limit of more than 10 kg/mm 2 , compared with 18% Cr-8% Ni austenitic steel. Also the developed steel has good ductility and toughness in spite of the high yield strength and shows better machinability than usual high Mn non- magnetic steels. The large forgings of this newly developed steel are manufactured in the works for the equipments of nuclear fusion research and confirmed good mechanical properties, high fatigue strength and low permeability. (author)

  19. Yield-determining factors in high-solids enzymatic hydrolysis of lignocellulose

    Directory of Open Access Journals (Sweden)

    Felby Claus

    2009-06-01

    Full Text Available Abstract Background Working at high solids (substrate concentrations is advantageous in enzymatic conversion of lignocellulosic biomass as it increases product concentrations and plant productivity while lowering energy and water input. However, for a number of lignocellulosic substrates it has been shown that at increasing substrate concentration, the corresponding yield decreases in a fashion which can not be explained by current models and knowledge of enzyme-substrate interactions. This decrease in yield is undesirable as it offsets the advantages of working at high solids levels. The cause of the 'solids effect' has so far remained unknown. Results The decreasing conversion at increasing solids concentrations was found to be a generic or intrinsic effect, describing a linear correlation from 5 to 30% initial total solids content (w/w. Insufficient mixing has previously been shown not to be involved in the effect. Hydrolysis experiments with filter paper showed that neither lignin content nor hemicellulose-derived inhibitors appear to be responsible for the decrease in yields. Product inhibition by glucose and in particular cellobiose (and ethanol in simultaneous saccharification and fermentation at the increased concentrations at high solids loading plays a role but could not completely account for the decreasing conversion. Adsorption of cellulases was found to decrease at increasing solids concentrations. There was a strong correlation between the decreasing adsorption and conversion, indicating that the inhibition of cellulase adsorption to cellulose is causing the decrease in yield. Conclusion Inhibition of enzyme adsorption by hydrolysis products appear to be the main cause of the decreasing yields at increasing substrate concentrations in the enzymatic decomposition of cellulosic biomass. In order to facilitate high conversions at high solids concentrations, understanding of the mechanisms involved in high-solids product inhibition

  20. Microbial Electrolysis Cells for High Yield Hydrogen Gas Production from Organic Matter

    NARCIS (Netherlands)

    Logan, B.E.; Call, D.; Cheng, S.; Hamelers, H.V.M.; Sleutels, T.H.J.A.; Jeremiasse, A.W.; Rozendal, R.A.

    2008-01-01

    The use of electrochemically active bacteria to break down organic matter, combined with the addition of a small voltage (>0.2 V in practice) in specially designed microbial electrolysis cells (MECs), can result in a high yield of hydrogen gas. While microbial electrolysis was invented only a few

  1. Response of high yielding rice varieties to NaCl salinity in ...

    African Journals Online (AJOL)

    In order to find resistant varieties and study the reaction of some newly released high yielding varieties to different levels of salinity of irrigation water an experiment was conducted at the Rice Research Institute of Iran-Amol station in a greenhouse. Eight varieties, cultivated in pots, were tested with three levels of salinity (2, ...

  2. CULTIVAR RELEASE - FAEM Carlasul: new white oat cultivar with high grain yield

    Directory of Open Access Journals (Sweden)

    Antônio Costa de Oliveira

    2012-01-01

    Full Text Available The white oat cultivar FAEM Carlasul was developed at the Plant Genomics and Breeding Center, Faculty of Agronomy Eliseu Maciel, Federal University of Pelotas, as a result of the cross between UFRGS 10 and 90SAT-28 (Coronado2/Cortez3/Pendek/ME 1563. It is characterized by high yield and grain quality.

  3. Upconverting core-shell nanocrystals with high quantum yield under low irradiance: On the role of isotropic and thick shells

    Energy Technology Data Exchange (ETDEWEB)

    Fischer, Stefan; Goldschmidt, Jan Christoph [Fraunhofer Institute for Solar Energy Systems, Heidenhofstraße 2, 79110 Freiburg (Germany); Johnson, Noah J. J.; Pichaandi, Jothirmayanantham; Veggel, Frank C. J. M. van [Department of Chemistry, University of Victoria, P.O. Box 3065, Victoria, British Columbia V8W 3V6 (Canada)

    2015-11-21

    Colloidal upconverter nanocrystals (UCNCs) that convert near-infrared photons to higher energies are promising for applications ranging from life sciences to solar energy harvesting. However, practical applications of UCNCs are hindered by their low upconversion quantum yield (UCQY) and the high irradiances necessary to produce relevant upconversion luminescence. Achieving high UCQY under practically relevant irradiance remains a major challenge. The UCQY is severely limited due to non-radiative surface quenching processes. We present a rate equation model for migration of the excitation energy to show that surface quenching does not only affect the lanthanide ions directly at the surface but also many other lanthanide ions quite far away from the surface. The average migration path length is on the order of several nanometers and depends on the doping as well as the irradiance of the excitation. Using Er{sup 3+}-doped β-NaYF{sub 4} UCNCs, we show that very isotropic and thick (∼10 nm) β-NaLuF{sub 4} inert shells dramatically reduce the surface-related quenching processes, resulting in much brighter upconversion luminescence at simultaneously considerably lower irradiances. For these UCNCs embedded in poly(methyl methacrylate), we determined an internal UCQY of 2.0% ± 0.2% using an irradiance of only 0.43 ± 0.03 W/cm{sup 2} at 1523 nm. Normalized to the irradiance, this UCQY is 120× higher than the highest values of comparable nanomaterials in the literature. Our findings demonstrate the important role of isotropic and thick shells in achieving high UCQY at low irradiances from UCNCs. Additionally, we measured the additional short-circuit current due to upconversion in silicon solar cell devices as a proof of concept and to support our findings determined using optical measurements.

  4. Derriçadora portátil na colheita total e seletiva de frutos do cafeeiro Portable harvester in the total and selective harvesting of coffee fruits

    Directory of Open Access Journals (Sweden)

    Cristiano Márcio Alves de Souza

    2006-11-01

    Full Text Available O objetivo deste trabalho foi avaliar o desempenho de derriçadoras portáteis durante a colheita seletiva e total dos frutos, em dois sistemas de colheita. Foram determinados a carga pendente da planta, a capacidade de derriça, o índice de desfolha, a eficiência de derriça, o índice de frutos verdes no produto, o nível de ruído e o consumo horário e específico de combustível. O sistema de colheita, utilizando-se duas derriçadoras portáteis, simultaneamente na mesma fileira de cafeeiros, apresentou melhor desempenho. A colheita seletiva foi muito influenciada pela porcentagem de frutos maduros e carga pendente do cafeeiro.The objective of this work was to evaluate the performance of a portable coffee harvester to mountain areas. Two procedures were tested: harvesting all fruits in only one operation, and the selective harvesting. Coffee yield, harvesting capacity, index of leaves taken during harvesting process, harvesting efficiency, noise level and fuel consumption were measured. The harvesting system with two portable harvester presented better performance than with only one machine. Selective harvesting was highly influenced by the percentage of ripen fruits and by coffee yield.

  5. Induced high yielding mutant in green gram (Vigna radiata (L.) Wilczek)

    International Nuclear Information System (INIS)

    Pulivarthi, H.R.; Mary, T.N.

    1987-01-01

    Green gram (mungbean) plays a significant role in meeting the protein requirements in India, with its predominantly vegetarian population. Therefore, an attempt was made to induce desirable mutants. Dry seed of cultivar 'Pusa 105' were irradiated with gamma rays ranging from 10 to 50 krad. A high yielding mutant (Hy I) identified in the M 4 generation from 40 krad dose, has shown significant increases in the number of pods/plants, number of branches/plant, and yield/plant. Further work is in progress. Comparison of the mutant HyI with the parent cultivar Pusa 105 is given

  6. Screening on the high yield validamycin producing strain by implantation with N+ and Ti+ ion source

    International Nuclear Information System (INIS)

    Yu Long; An Xiao

    2007-01-01

    In order to compared the mutagenic effects of the validamycin producing the strain (Streptomyces hygroscopicus var. Jingganggensis Yen.) was implanted with two kinds of ion sources. The results showed that when two kinds of ion sources implanted into the strain by turns, more positive mutants and higher yield would be acquired. Using this method, a high-yielding strain B1-3 was obtained, which produce the titer of validamycin A of 21514, and was 54.4% higher than that of the original strain. (authors)

  7. Study of Bokashi’s Type and Dosages to Growth and Harvest Yield Honey Dews (Cucumis Melo L. In Low Land

    Directory of Open Access Journals (Sweden)

    Ana Amiroh

    2016-12-01

    Full Text Available Recently, most cultivation and planting of Melon (Cucumis melo L. by farmers using inorganic fertilizers with an excessive dosage, and this causes the lowland productivity decrease with consequent. The soil organic matter decreased as low as time increasing. Application and using of mature organic matter are an alternative to solve these problems in order the lowland become more conducive and productive for growth of melon. But increasing pests and diseases attaching to the plants may caused by adding immature organic matters into soil. Sources to make bokashi like as paddy straw and water hyacinth is immense but it’s not yet used. This research was aimed to study, know and usage of paddy straw and water hyacinth bokashi’s on melon growing at lowland. Experiment was conducted at Lowland Experiment Station of Agricultural Faculty, Brawijaya, in Jatikerto Village, Kromengan Distric, Malang, from April-June 2015. Experiment was applied in a Randomized Block Design (RBD with double factors Types and Dosages of Bokashis. There is seven combinations of treatment with three replications, each treatment consisted four individual plants. Result showed there is significant difference between types and dosages of bokashi on plant length at 28, 35, 42 dan 49 days after planting (d,a,p respectively. The significant difference between treatment also shown by leaf area at 28 - 49 (d.a.p.. Application of paddy straw bokashi was better than hyacinth bokashi on melon growth. The best yield shows that by using paddy straw bokashi with 5 ton/ha of dosage gives melon with 2,56 kg /plant fresh weight.

  8. Target design for high fusion yield with the double Z-pinch-driven hohlraum

    International Nuclear Information System (INIS)

    Vesey, R. A.; Herrmann, M. C.; Lemke, R. W.; Desjarlais, M. P.; Cuneo, M. E.; Stygar, W. A.; Bennett, G. R.; Campbell, R. B.; Christenson, P. J.; Mehlhorn, T. A.; Porter, J. L.; Slutz, S. A.

    2007-01-01

    A key demonstration on the path to inertial fusion energy is the achievement of high fusion yield (hundreds of MJ) and high target gain. Toward this goal, an indirect-drive high-yield inertial confinement fusion (ICF) target involving two Z-pinch x-ray sources heating a central secondary hohlraum is described by Hammer et al. [Phys. Plasmas 6, 2129 (1999)]. In subsequent research at Sandia National Laboratories, theoretical/computational models have been developed and an extensive series of validation experiments have been performed to study hohlraum energetics, capsule coupling, and capsule implosion symmetry for this system. These models have been used to design a high-yield Z-pinch-driven ICF target that incorporates the latest experience in capsule design, hohlraum symmetry control, and x-ray production by Z pinches. An x-ray energy output of 9 MJ per pinch, suitably pulse-shaped, is sufficient for this concept to drive 0.3-0.5 GJ capsules. For the first time, integrated two-dimensional (2D) hohlraum/capsule radiation-hydrodynamics simulations have demonstrated adequate hohlraum coupling, time-dependent radiation symmetry control, and the successful implosion, ignition, and burn of a high-yield capsule in the double Z-pinch hohlraum. An important new feature of this target design is mode-selective symmetry control: the use of burn-through shields offset from the capsule that selectively tune certain low-order asymmetry modes (P 2 ,P 4 ) without significantly perturbing higher-order modes and without a significant energy penalty. This paper will describe the capsule and hohlraum design that have produced 0.4-0.5 GJ yields in 2D simulations, provide a preliminary estimate of the Z-pinch load and accelerator requirements necessary to drive the system, and suggest future directions for target design work

  9. Factors affecting the optimal performance of a high-yield pulping operation

    Energy Technology Data Exchange (ETDEWEB)

    Broderick, G [Noranda Technology Centre, Pointe-Claire, PQ (Canada); Paris, J [Ecole Polytechnique, Montreal, PQ (Canada); Valada, J L [Quebec Univ., Trois-Rivieres, PQ (Canada)

    1995-06-01

    Strategies for operating a chemical-mechanical pulp mill were investigated from data based on process models from some one hundred pilot scale pulping runs. Optimal values for 55 process and pulp quality variables have been calculated by applying a genetic algorithm search to a fuzzy model of the overall system. Best pulp quality was achieved and maintained when the chemical pretreatment was conducted at moderately low temperatures using a high SO{sub 2} concentration, which produced high sulphonation and high yield at the same time. By characterizing the quality of the pulp at the fibre level, optimization results were said to be more easily transferable to other high yield pulping systems. 19 refs., 6 tabs.

  10. Differential metabolite profiles during fruit development in high-yielding oil palm mesocarp.

    Directory of Open Access Journals (Sweden)

    Huey Fang Teh

    Full Text Available To better understand lipid biosynthesis in oil palm mesocarp, in particular the differences in gene regulation leading to and including de novo fatty acid biosynthesis, a multi-platform metabolomics technology was used to profile mesocarp metabolites during six critical stages of fruit development in comparatively high- and low-yielding oil palm populations. Significantly higher amino acid levels preceding lipid biosynthesis and nucleosides during lipid biosynthesis were observed in a higher yielding commercial palm population. Levels of metabolites involved in glycolysis revealed interesting divergence of flux towards glycerol-3-phosphate, while carbon utilization differences in the TCA cycle were proven by an increase in malic acid/citric acid ratio. Apart from insights into the regulation of enhanced lipid production in oil palm, these results provide potentially useful metabolite yield markers and genes of interest for use in breeding programmes.

  11. Microbial Electrolysis Cells for High Yield Hydrogen Gas Production from Organic Matter

    KAUST Repository

    Logan, Bruce E.

    2008-12-01

    The use of electrochemically active bacteria to break down organic matter, combined with the addition of a small voltage (>0.2 V in practice) in specially designed microbial electrolysis cells (MECs), can result in a high yield of hydrogen gas. While microbial electrolysis was invented only a few years ago, rapid developments have led to hydrogen yields approaching 100%, energy yields based on electrical energy input many times greater than that possible by water electrolysis, and increased gas production rates. MECs used to make hydrogen gas are similar in design to microbial fuel cells (MFCs) that produce electricity, but there are important differences in architecture and analytical methods used to evaluate performance. We review here the materials, architectures, performance, and energy efficiencies of these MEC systems that show promise as a method for renewable and sustainable energy production, and wastewater treatment. © 2008 American Chemical Society.

  12. Maximization of DRAM yield by control of surface charge and particle addition during high dose implantation

    Science.gov (United States)

    Horvath, J.; Moffatt, S.

    1991-04-01

    Ion implantation processing exposes semiconductor devices to an energetic ion beam in order to deposit dopant ions in shallow layers. In addition to this primary process, foreign materials are deposited as particles and surface films. The deposition of particles is a major cause of IC yield loss and becomes even more significant as device dimensions are decreased. Control of particle addition in a high-volume production environment requires procedures to limit beamline and endstation sources, control of particle transport, cleaning procedures and a well grounded preventative maintenance philosophy. Control of surface charge by optimization of the ion beam and electron shower conditions and measurement with a real-time charge sensor has been effective in improving the yield of NMOS and CMOS DRAMs. Control of surface voltages to a range between 0 and -20 V was correlated with good implant yield with PI9200 implanters for p + and n + source-drain implants.

  13. High-Yield Production of Levulinic Acid from Pretreated Cow Dung in Dilute Acid Aqueous Solution

    Directory of Open Access Journals (Sweden)

    Jialei Su

    2017-02-01

    Full Text Available Agricultural waste cow dung was used as feedstock for the production of a high value–added chemical levulinic acid (LA in dilute acid aqueous solutions. A high LA yield of 338.9 g/kg was obtained from the pretreated cow dung, which was much higher than that obtained from the crude cow dung (135 g/kg, mainly attributed to the breakage of the lignin fraction in the lignocellulose structure of the cow dung by potassium hydroxide (KOH pretreatment, and thus enhanced the accessibility of cow dung to the acid sites in the catalytic reaction. Meanwhile, another value-added chemical formic acid could be obtained with a yield of ca. 160 g/kg in the process, implying a total production of ca. 500 g/kg yield for LA and formic acid from the pretreated cow dung with the proposed process. The developed process was shown to be tolerant to high initial substrate loading with a satisfied LA yield. This work provides a promising strategy for the value-increment utilization of liglocellulosic agricultural residues.

  14. The studies on radiation mutation breeding of Bacillus subtilis with high-yield of amylase

    International Nuclear Information System (INIS)

    Chen Xiaoming; Zhang Liang; Zhang Jianguo; Zhou Liwei

    2008-01-01

    The mutagenesis effects on the yield of amylase have been investigated with Bacillus subtilis irradiated by γ-rays and fast neutrons in once or twice irradiation at various dose rates and total irradiation doses. Several parameters such as flat transparent circle, colony diameter, transparent circle diameter and the ratio of flat transparent circle to colony diameter (HC) are used to estimate the radiation mutation of Bacillus subtilis. A series of results has been obtained as (1) Irradiation both with neutrons and γ-rays could make Bacillus subtilis mutationed to produce high-yield amylase effectively. (2) The average colony diameter of Bacillus subtilis irradiated by γ-rays or fast neutrons is smaller than that of control group at various total doses and dose rates. And their colony diameter becomes smaller slightly with the increment of γ-rays irradiation dose. (3) After the second neutrons irradiation, the values of average colony diameter, the biggest colony diameter, average transparent circle diameter and the biggest transparent circle diameter of all mutationed Bacillus subtilis exceed that of original strains greatly. (4) Three kinds of mutationed Bacillus subtilis strains with high-yield amylase have been screened out, in which two strains can produce high-yield amylase steadily after 15 times breeding. Their biggest colony diameter, the biggest transparent circle diameter and the biggest HC value are up to 8.32 mm, 22.38 mm and 5.39 respectively. (authors)

  15. Origin of the reversed yield asymmetry in Mg-rare earth alloys at high temperature

    International Nuclear Information System (INIS)

    Hidalgo-Manrique, P.; Herrera-Solaz, V.; Segurado, J.; Llorca, J.; Gálvez, F.; Ruano, O.A.; Yi, S.B.; Pérez-Prado, M.T.

    2015-01-01

    The mechanical behaviour in tension and compression of an extruded Mg–1 wt.% Mn–1 wt.% Nd (MN11) alloy was studied along the extrusion direction in the temperature range −175 °C to 300 °C at both quasi-static and dynamic strain rates. Microstructural analysis revealed that the as-extruded bar presents a recrystallized microstructure and a weak texture that remain stable in the whole temperature range. A remarkable reversed yield stress asymmetry was observed above 150 °C, with the compressive yield stress being significantly higher than the tensile yield stress. The origin of this anomalous reversed yield stress asymmetry, which to date remains unknown, was investigated through the analysis of the macro and microtexture development during deformation, as well as by means of crystal plasticity finite element simulations of a representative volume element of the polycrystal. The critical resolved shear stresses of slip and twining for simulated single crystals were obtained as a function of the temperature by means of an inverse optimisation strategy. Experimental and simulation results suggest that the reversed yield asymmetry may be primarily attributed to the non-Schmid behaviour of pyramidal 〈c + a〉 slip, which is the dominant deformation mechanism at high temperatures. It is proposed, furthermore, that the asymmetry is enhanced at quasi-static strain rates by the stronger interaction of 〈c + a〉 dislocations with the diffusing solute atoms and particles in compression than in tension

  16. Selected wild strains of Agaricus bisporus produce high yields of mushrooms at 25°C.

    Science.gov (United States)

    Navarro, Pilar; Savoie, Jean-Michel

    2015-01-01

    To cultivate the button mushroom Agaricus bisporus in warm countries or during summer in temperate countries, while saving energy, is a challenge that could be addressed by using the biological diversity of the species. The objective was to evaluate the yield potential of eight wild strains previously selected in small scale experiments for their ability to produce mature fruiting bodies at 25°C and above. Culture units of 8 kg of compost were used. The yield expressed as weight or number per surface unit and earliness of fruiting were recorded during cultivation in climatic rooms at 17, 25 or 30°C. Only strains of A. bisporus var. burnettii were able to fruit at 30°C. At 25°C they produced the highest yields (27 kg m(-2)) and had best earliness. The yields at 25°C for the strains of A. bisporus var. bisporus ranged from 12 to 16 kg m(-2). The yield ratios 25°C/17°C ranged from 0.8 to 1.2. The variety burnettii originated in the Sonoran Desert in California showed adaptation for quickly producing fruiting bodies at high temperature when humidity conditions were favorable. Strains of the variety bisporus showed interesting potentials for their ability to produce mature fruiting bodies at higher temperature than present cultivars and might be used in breeding programs. Copyright © 2012 Revista Iberoamericana de Micología. Published by Elsevier Espana. All rights reserved.

  17. High Photoluminescence Quantum Yield in Band Gap Tunable Bromide Containing Mixed Halide Perovskites.

    Science.gov (United States)

    Sutter-Fella, Carolin M; Li, Yanbo; Amani, Matin; Ager, Joel W; Toma, Francesca M; Yablonovitch, Eli; Sharp, Ian D; Javey, Ali

    2016-01-13

    Hybrid organic-inorganic halide perovskite based semiconductor materials are attractive for use in a wide range of optoelectronic devices because they combine the advantages of suitable optoelectronic attributes and simultaneously low-cost solution processability. Here, we present a two-step low-pressure vapor-assisted solution process to grow high quality homogeneous CH3NH3PbI3-xBrx perovskite films over the full band gap range of 1.6-2.3 eV. Photoluminescence light-in versus light-out characterization techniques are used to provide new insights into the optoelectronic properties of Br-containing hybrid organic-inorganic perovskites as a function of optical carrier injection by employing pump-powers over a 6 orders of magnitude dynamic range. The internal luminescence quantum yield of wide band gap perovskites reaches impressive values up to 30%. This high quantum yield translates into substantial quasi-Fermi level splitting and high "luminescence or optically implied" open-circuit voltage. Most importantly, both attributes, high internal quantum yield and high optically implied open-circuit voltage, are demonstrated over the entire band gap range (1.6 eV ≤ Eg ≤ 2.3 eV). These results establish the versatility of Br-containing perovskite semiconductors for a variety of applications and especially for the use as high-quality top cell in tandem photovoltaic devices in combination with industry dominant Si bottom cells.

  18. NUTRIENT BALANCE IN WATER HARVESTING SOILS

    Directory of Open Access Journals (Sweden)

    Díaz, F

    2005-05-01

    Full Text Available Dryland farming on Fuerteventura and Lanzarote (Canary Islands, Spain, which has an annual rainfall of less than 150 mm/year, has been based traditionally on water harvesting techniques (known locally as “gavias”. Periods of high productivity alternate with those of very low yield. The systems are sustainable in that they reduce erosive processes, contribute to soil and soil-water conservation and are largely responsible for maintaining the soil’s farming potential. In this paper we present the chemical fertility status and nutrient balance of soils in five “gavia” systems. The results are compared with those obtained in adjacent soils where this water harvesting technique is not used. The main crops are wheat, barley, maize, lentils and chick-peas. Since neither organic nor inorganic fertilisers are used, nutrients are derived mainly from sediments carried by runoff water. Nutrients are lost mainly through crop harvesting and harvest residues. The soils where water harvesting is used have lower salt and sodium in the exchange complex, are higher in carbon, nitrogen, copper and zinc and have similar phosphorous and potassium content. It is concluded that the systems improve the soil’s natural fertility and also that natural renovation of nutrients occurs thanks to the surface deposits of sediments, which mix with the arable layer. The system helps ensure adequate fertility levels, habitual in arid regions, thus allowing dryland farming to be carried out.

  19. Nanofluidic crystal: a facile, high-efficiency and high-power-density scaling up scheme for energy harvesting based on nanofluidic reverse electrodialysis

    International Nuclear Information System (INIS)

    Ouyang Wei; Wang Wei; Zhang Haixia; Wu Wengang; Li Zhihong

    2013-01-01

    The great advances in nanotechnology call for advances in miniaturized power sources for micro/nano-scale systems. Nanofluidic channels have received great attention as promising high-power-density substitutes for ion exchange membranes for use in energy harvesting from ambient ionic concentration gradient, namely reverse electrodialysis. This paper proposes the nanofluidic crystal (NFC), of packed nanoparticles in micro-meter-sized confined space, as a facile, high-efficiency and high-power-density scaling-up scheme for energy harvesting by nanofluidic reverse electrodialysis (NRED). Obtained from the self-assembly of nanoparticles in a micropore, the NFC forms an ion-selective network with enormous nanochannels due to electrical double-layer overlap in the nanoparticle interstices. As a proof-of-concept demonstration, a maximum efficiency of 42.3 ± 1.84%, a maximum power density of 2.82 ± 0.22 W m −2 , and a maximum output power of 1.17 ± 0.09 nW/unit (nearly three orders of magnitude of amplification compared to other NREDs) were achieved in our prototype cell, which was prepared within 30 min. The current NFC-based prototype cell can be parallelized and cascaded to achieve the desired output power and open circuit voltage. This NFC-based scaling-up scheme for energy harvesting based on NRED is promising for the building of self-powered micro/nano-scale systems. (paper)

  20. Synthesis and characterization of poly (dihydroxybiphenyl borate) with high char yield for high-performance thermosetting resins

    Science.gov (United States)

    Wang, Shujuan; Xing, Xiaolong; Li, Jian; Jing, Xinli

    2018-01-01

    The objective of the current work is to synthesize novel boron-containing polymers with excellent thermal resistance, and reveal the structure and the reason for the high char yield. Thus, poly (dihydroxybiphenyl borate) (PDDB) with a more rigid molecular chain, was successfully synthesized using 4,4‧-dihydroxybiphenyl and boric acid. Structural characterizations of the prepared PDDB were performed via NMR, FTIR, XPS, and XRD analyses. The results reveal that PDDB consists of aromatic, Phsbnd Osbnd B and Bsbnd Osbnd B structures as well as a small number of boron hydroxyl and phenolic hydroxyl groups. PDDB shows good solubility in strong polar solvents, which is of great importance for the modification of thermosetting resins. TGA combined with DSC were employed to evaluate the thermal properties of PDDB, and increases in the glass transition temperature (Tg) and char yield were observed with increased boron content. Tg and char yield of PDDB (800 °C, nitrogen atmosphere) reached up to 219 °C and 66.5%, respectively. PDDB was extensively characterized during pyrolysis to reveal the high char yield of PDDB. As briefly discussed, the boron oxide and boron carbide that formed during pyrolysis play a crucial role in the high char yield of PDDB, which reduces the release of volatile carbon dioxide and carbon. This research suggests that PDDB has great potential as a novel modified agent for the improvement of the comprehensive performance of thermosetting resins to broaden their applicability in the field of advanced composites.

  1. Fast and inexpensive synthesis of pentacene with high yield using 6,13-pentacenequinone as precursor

    Science.gov (United States)

    Mota, María L.; Rodriguez, Bibiana; Carrillo, Amanda; Ambrosio, Roberto C.; Luque, Priscy A.; Mireles, Marcela; Vivaldo, Israel; Quevedo, Manuel A.

    2018-02-01

    Pentacene is an important semiconductor in the field of organic electronics. In this work is presented an alternative synthesis procedure to obtain pentacene from 6,13-pentacenequinone as a precursor. Synthesis of pentacene was performed in two reactions, Diels-Adler cycloaddition of 6,13-pentacenequinone followed by 6,13-pentacenequinone reduction to pentacene, employing LiAlH4 as reducing agent. The products were characterized by Fourier Transform Infrared Spectroscopy (FTIR), 1H-Nuclear Magnetic Resonance Spectroscopy (1H-NMR), X-Ray Diffraction (XRD), Thermogravimetric Analysis (TGA) and Ultraviolet-Visible Spectroscopy (UV-VIS). In this work, 6,13-pentacenequinone was synthetized with a high yield (55%) using an alternative method. The optimization process resulted in an overall reduction of reaction time while exhibiting high yield. The method presented here provides an affordable pentacene synthesis route with high purity, which can be further applied for research and development of organic electronic applications.

  2. Ultra-broadband nonlinear saturable absorption of high-yield MoS2 nanosheets

    Science.gov (United States)

    Wei, Rongfei; Zhang, Hang; Hu, Zhongliang; Qiao, Tian; He, Xin; Guo, Qiangbing; Tian, Xiangling; Chen, Zhi; Qiu, Jianrong

    2016-07-01

    High-yield MoS2 nanosheets with strong nonlinear optical (NLO) responses in a broad near-infrared range were synthesized by a facile hydrothermal method. The observation of saturable absorption, which was excited by the light with photon energy smaller than the gap energy of MoS2, can be attributed to the enhancement of the hybridization between the Mo d-orbital and S p-orbital by the oxygen incorporation into MoS2. High-yield MoS2 nanosheets with high modulation depth and large saturable intensity generated a stable, passively Q-switched fiber laser pulse at 1.56 μm. The high output power of 1.08 mW can be attained under a very low pump power of 30.87 mW. Compared to recently reported passively Q-switched fiber lasers utilizing exfoliated MoS2 nanosheets, the efficiency of the laser for our passive Q-switching operation is larger and reaches 3.50%. This research may extend the understanding on the NLO properties of MoS2 and indicate the feasibility of the high-yield MoS2 nanosheets to passively Q-switched fiber laser effectively at low pump strengths.

  3. Development of bioprocess for high density cultivation yield of the probiotic Bacillus coagulans and its spores

    Directory of Open Access Journals (Sweden)

    Kavita R. Pandey

    2016-09-01

    Full Text Available Bacillus coagulans is a spore forming lactic acid bacterium. Spore forming bacteria, have been extensively studied and commercialized as probiotics. Probiotics are produced by fermentation technology. There is a limitation to biomass produced by conventional modes of fermentation. With the great demand generated by range of probiotic products, biomass is becoming very valuable for several pharmaceutical, dairy and probiotic companies. Thus, there is a need to develop high cell density cultivation processes for enhanced biomass accumulation. The bioprocess development was carried out in 6.6 L bench top lab scale fermentor. Four different cultivation strategies were employed to develop a bioprocess for higher growth and sporulation efficiencies of probiotic B. coagulans. Batch fermentation of B. coagulans yielded 18 g L-1 biomass (as against 8.0 g L-1 productivity in shake flask with 60% spore efficiency. Fed-batch cultivation was carried out for glucose, which yielded 25 g L-1 of biomass. C/N ratio was very crucial in achieving higher spore titres. Maximum biomass yield recorded was 30 g L-1, corresponding to 3.8 × 1011 cells mL-1 with 81% of cells in sporulated stage. The yield represents increment of 85 times the productivity and 158 times the spore titres relative to the highest reported values for high density cultivation of B. coagulans.

  4. Yield Evaluation of Nutrient-rich Potato Clones in High Hill of Nepal

    Directory of Open Access Journals (Sweden)

    Binod Prasad Luitel

    2017-05-01

    Full Text Available A study was conducted to evaluate the yield of nutrient-rich potato clones in high-hill districts: Dolakha and Jumla of Nepal during the years 2013 and 2014, respectively. Fourteen potato clones were tested as on-station and on-farm experiments at both districts, and those fourteen clones were compared to ‘Lady Rosita’ and ‘Jumli Local’ respectively as the check varieties in the first year experiment, 2013. Eight promising clones were selected from the first year experiment, and were evaluated and compared with same local varieties in the consecutive year, 2014. Two clones namely; CIP 395112.32 (19.3 tha-1 and CIP 393073.179 (17.8 tha-1 exhibited superior marketable tuber yield than that of ‘Lady Rosita’(14.2 tha-1 in Dolakha and five CIP clones namely; 395112.32 (25.5 tha-1, 393073.179 (22.5 tha-1, 394611.112 (20.9 tha-1, 390478.9 (19.9 tha-1 and 395017.229 (17.0 tha-1 showed higher marketable tuber yield than ‘Jumli Local’(14.5 tha-1. Based on two years’ phenotypic and tuber yield result, clones CIP 395112.32 and CIP 393073.179 are recommended to potato growers at high hills of Nepal for commercial cultivation.

  5. Facile high-yield synthesis of polyaniline nanosticks with intrinsic stability and electrical conductivity.

    Science.gov (United States)

    Li, Xin-Gui; Li, Ang; Huang, Mei-Rong

    2008-01-01

    Chemical oxidative polymerization at 15 degrees C was used for the simple and productive synthesis of polyaniline (PAN) nanosticks. The effect of polymerization media on the yield, size, stability, and electrical conductivity of the PAN nanosticks was studied by changing the concentration and nature of the acid medium and oxidant and by introducing organic solvent. Molecular and supramolecular structure, size, and size distribution of the PAN nanosticks were characterized by UV/Vis and IR spectroscopy, X-ray diffraction, laser particle-size analysis, and transmission electron microscopy. Introduction of organic solvent is advantageous for enhancing the yield of PAN nanosticks but disadvantageous for formation of PAN nanosticks with small size and high conductivity. The concentration and nature of the acid medium have a major influence on the polymerization yield and conductivity of the nanosized PAN. The average diameter and length of PAN nanosticks produced with 2 M HNO(3) and 0.5 M H(2)SO(4) as acid media are about 40 and 300 nm, respectively. The PAN nanosticks obtained in an optimal medium (i.e., 2 M HNO(3)) exhibit the highest conductivity of 2.23 S cm(-1) and the highest yield of 80.7 %. A mechanism of formation of nanosticks instead of nanoparticles is proposed. Nanocomposite films of the PAN nanosticks with poly(vinyl alcohol) show a low percolation threshold of 0.2 wt %, at which the film retains almost the same transparency and strength as pure poly(vinyl alcohol) but 262 000 times the conductivity of pure poly(vinyl alcohol) film. The present synthesis of PAN nanosticks requires no external stabilizer and provides a facile and direct route for fabrication of PAN nanosticks with high yield, controllable size, intrinsic self-stability, strong redispersibility, high purity, and optimizable conductivity.

  6. High-yield production of herbicidal thaxtomins and analogs in a nonpathogenic Streptomyces strain.

    Science.gov (United States)

    Jiang, Guangde; Zhang, Yucheng; Powell, Magan M; Zhang, Peilan; Zuo, Ran; Zhang, Yi; Kallifidas, Dimitrios; Tieu, Albert M; Luesch, Hendrik; Loria, Rosemary; Ding, Yousong

    2018-03-30

    Thaxtomins are virulence factors of most plant pathogenic Streptomyces strains. Due to their potent herbicidal activity, attractive environmental compatibility and inherent biodegradability, thaxtomins are key active ingredients of bioherbicides approved by the United States Environmental Protection Agency. However, the low yield of thaxtomins in native Streptomyces producers limits their wide agricultural applications. Here, we describe the high-yield production of thaxtomins in a heterologous host. The thaxtomin gene cluster from S. scabiei 87.22 was cloned and expressed in S. albus J1074 after chromosomal integration. The production of thaxtomins and nitro-tryptophan analogs were observed using LC-MS analysis. When culturing the engineered S. albus J1074 in the minimal medium TMDc, the yield of the most abundant and herbicidal analog, thaxtomin A, was 10 times higher than S. scabiei 87.22, and optimization of the medium resulted in the highest yield of thaxtomin analogs at about 222 mg/L. Further engineering of the thaxtomin biosynthetic gene cluster through gene deletion led to the production of multiple biosynthetic intermediates important to the chemical synthesis of new analogs. Additionally, the versatility of the thaxtomin biosynthetic system in S. albus J1074 was capitalized to produce one unnatural fluorinated analog 5-F-thaxtomin A, whose structure was elucidated by a combination of MS and 1D and 2D NMR analyses. Natural and unnatural thaxtomins demonstrated potent herbicidal activity in radish seedling assays. These results indicated that S. albus J1074 has the potential to produce thaxtomins and thereof with high yield, fostering their agricultural applications. IMPORTANCE Thaxtomins are agriculturally valuable herbicidal natural products but the productivity of native producers is limiting. Heterologous expression of thaxtomin gene cluster in S. albus J1074 resulted in the highest yield of thaxtomins ever reported, representing a significant leap

  7. RB962962, a sugarcane cultivar for late harvest

    Directory of Open Access Journals (Sweden)

    Luiz José Oliveira Tavares de Melo

    2014-07-01

    Full Text Available In the Northeast of Brazil, sugarcane cultivar RB962962 is harvested at the end of the cycle, between December and February, with a high sugar yield per area. Recommended for sandy soils of medium texture and fertility, it is resistant to the major diseases and fast-growing in plant and ratoon crops.

  8. Determination of Optimal Harvest Time of Chuchung Variety Green Rice(®) (Oryza sativa L.) with High Contents of GABA, γ-Oryzanol, and α-Tocopherol.

    Science.gov (United States)

    Kim, Hoon; Kim, Oui-Woung; Ha, Ae Wha; Park, Soojin

    2016-06-01

    In our previous study, an early-maturing variety of rice (Oryza sativa L.), Jinbu can have feature with unique green color, various phytochemicals as well as nutritive components by the optimal early harvesting, called Green Rice(®) (GR). The aims of the present field experiments were to evaluate the changes in the weight of 1,000 kernels, yield, and contents of proximate and bioactive compounds in Chuchung, a mid-late maturing variety, during the pre-harvest maturation of rough rice and to research the appropriate harvest time and potent bioactivity of Chuchung GR. The weights of 1,000 kernels of Chuchung GR dramatically increased until 27 days after heading (DAH). The yields of Chuchung GR declined after 27 DAH and significantly declined to 0.0% after 45 DAH. The caloric value and total mineral contents were higher in the GR than in the full ripe stage, the brown rice (BR). In the GR, the contents of bioactive compounds, such as γ-aminobutyric acid, γ-oryzanol, and α-tocopherol, were much higher (P<0.05) than those in the BR, specifically during 24~27 DAH. Therefore, bioactive Chuchung GR can be produced with a reasonable yield at 24~27 DAH and it could be useful for applications in various nutritive and functional food products.

  9. Determination of Optimal Harvest Time of Chuchung Variety Green Rice® (Oryza sativa L.) with High Contents of GABA, γ-Oryzanol, and α-Tocopherol

    Science.gov (United States)

    Kim, Hoon; Kim, Oui-Woung; Ha, Ae Wha; Park, Soojin

    2016-01-01

    In our previous study, an early-maturing variety of rice (Oryza sativa L.), Jinbu can have feature with unique green color, various phytochemicals as well as nutritive components by the optimal early harvesting, called Green Rice® (GR). The aims of the present field experiments were to evaluate the changes in the weight of 1,000 kernels, yield, and contents of proximate and bioactive compounds in Chuchung, a mid-late maturing variety, during the pre-harvest maturation of rough rice and to research the appropriate harvest time and potent bioactivity of Chuchung GR. The weights of 1,000 kernels of Chuchung GR dramatically increased until 27 days after heading (DAH). The yields of Chuchung GR declined after 27 DAH and significantly declined to 0.0% after 45 DAH. The caloric value and total mineral contents were higher in the GR than in the full ripe stage, the brown rice (BR). In the GR, the contents of bioactive compounds, such as γ-aminobutyric acid, γ-oryzanol, and α-tocopherol, were much higher (P<0.05) than those in the BR, specifically during 24~27 DAH. Therefore, bioactive Chuchung GR can be produced with a reasonable yield at 24~27 DAH and it could be useful for applications in various nutritive and functional food products. PMID:27390725

  10. Harvest Regulations and Implementation Uncertainty in Small Game Harvest Management

    Directory of Open Access Journals (Sweden)

    Pål F. Moa

    2017-09-01

    Full Text Available A main challenge in harvest management is to set policies that maximize the probability that management goals are met. While the management cycle includes multiple sources of uncertainty, only some of these has received considerable attention. Currently, there is a large gap in our knowledge about implemention of harvest regulations, and to which extent indirect control methods such as harvest regulations are actually able to regulate harvest in accordance with intended management objectives. In this perspective article, we first summarize and discuss hunting regulations currently used in management of grouse species (Tetraonidae in Europe and North America. Management models suggested for grouse are most often based on proportional harvest or threshold harvest principles. These models are all built on theoretical principles for sustainable harvesting, and provide in the end an estimate on a total allowable catch. However, implementation uncertainty is rarely examined in empirical or theoretical harvest studies, and few general findings have been reported. Nevertheless, circumstantial evidence suggest that many of the most popular regulations are acting depensatory so that harvest bag sizes is more limited in years (or areas where game density is high, contrary to general recommendations. A better understanding of the implementation uncertainty related to harvest regulations is crucial in order to establish sustainable management systems. We suggest that scenario tools like Management System Evaluation (MSE should be more frequently used to examine robustness of currently applied harvest regulations to such implementation uncertainty until more empirical evidence is available.

  11. Allometric analysis of the effects of density on reproductive allocation and Harvest Index in 6 varieties of wheat (Triticum)

    DEFF Research Database (Denmark)

    Qin, Xiao-liang; Weiner, Jacob; Qi, Lin

    2013-01-01

    allocation should be analyzed and interpreted allometrically because ratios or fractions such as Reproductive Effort or Harvest Index are size dependent. We investigated reproductive allocation of individuals in 6 varieties of Triticum (wheat) grown at a wide range of densities. We harvested leaves, stems...... size. There were significant differences among the varieties in the allometric exponent (slope of log–log relationship) of grain versus vegetative mass, such that some varieties produced higher yield (and therefore had a higher Harvest Index) than others when plants were small, while others had higher...... yield at larger sizes. Thus, the Harvest Index and its rank among varieties changed with plant size, which puts into question the practice of selecting for Harvest Index when crop performance varies greatly among individuals, years or environments. Selection for a high Harvest Index when individuals...

  12. Low LET radiolysis escape yields for reducing radicals and H2 in pressurized high temperature water

    Science.gov (United States)

    Sterniczuk, Marcin; Yakabuskie, Pamela A.; Wren, J. Clara; Jacob, Jasmine A.; Bartels, David M.

    2016-04-01

    Low Linear Energy Transfer (LET) radiolysis escape yields (G values) are reported for the sum (G(radH)+G(e-)aq) and for G(H2) in subcritical water up to 350 °C. The scavenger system 1-10 mM acetate/0.001 M hydroxide/0.00048 M N2O was used with simultaneous mass spectroscopic detection of H2 and N2 product. Temperature-dependent measurements were carried out with 2.5 MeV electrons from a van de Graaff accelerator, while room temperature calibration measurements were done with a 60Co gamma source. The concentrations and dose range were carefully chosen so that initial spur chemistry is not perturbed and the N2 product yield corresponds to those reducing radicals that escape recombination in pure water. In comparison with a recent review recommendation of Elliot and Bartels (AECL report 153-127160-450-001, 2009), the measured reducing radical yield is seven percent smaller at room temperature but in fairly good agreement above 150 °C. The H2 escape yield is in good agreement throughout the temperature range with several previous studies that used much larger radical scavenging rates. Previous analysis of earlier high temperature measurements of Gesc(radOH) is shown to be flawed, although the actual G values may be nearly correct. The methodology used in the present report greatly reduces the range of possible error and puts the high temperature escape yields for low-LET radiation on a much firmer quantitative foundation than was previously available.

  13. Will energy crop yields meet expectations?

    International Nuclear Information System (INIS)

    Searle, Stephanie Y.; Malins, Christopher J.

    2014-01-01

    Expectations are high for energy crops. Government policies in the United States and Europe are increasingly supporting biofuel and heat and power from cellulose, and biomass is touted as a partial solution to energy security and greenhouse gas mitigation. Here, we review the literature for yields of 5 major potential energy crops: Miscanthus spp., Panicum virgatum (switchgrass), Populus spp. (poplar), Salix spp. (willow), and Eucalyptus spp. Very high yields have been achieved for each of these types of energy crops, up to 40 t ha −1  y −1 in small, intensively managed trials. But yields are significantly lower in semi-commercial scale trials, due to biomass losses with drying, harvesting inefficiency under real world conditions, and edge effects in small plots. To avoid competition with food, energy crops should be grown on non-agricultural land, which also lowers yields. While there is potential for yield improvement for each of these crops through further research and breeding programs, for several reasons the rate of yield increase is likely to be slower than historically has been achieved for cereals; these include relatively low investment, long breeding periods, low yield response of perennial grasses to fertilizer, and inapplicability of manipulating the harvest index. Miscanthus × giganteus faces particular challenges as it is a sterile hybrid. Moderate and realistic expectations for the current and future performance of energy crops are vital to understanding the likely cost and the potential of large-scale production. - Highlights: • This review covers Miscanthus, switchgrass, poplar, willow, and Eucalyptus. • High yields of energy crops are typically from small experimental plots. • Field scale yields are lower due to real world harvesting losses and edge effects. • The potential for yield improvement of energy crops is relatively limited. • Expectations must be realistic for successful policies and commercial production

  14. A simple, high-yield, apparatus for NEG coating of vacuum beamline elements

    International Nuclear Information System (INIS)

    Ron, G; Oort, R; Lee, D

    2010-01-01

    Non-Evaporable Getter (NEG) materials are extremely useful in vacuum systems for achieving Ultra High Vacuum. Recently, these materials have been used to coat the inner surfaces of vacuum components, acting as an internal, passive, vacuum pump. We have constructed a low cost apparatus, which allows coating of very small diameter vacuum tubes, used as differential pumping stages. Despite the relative ease of construction, we are routinely able to achieve high coating yields. We further describe an improvement to our system, which is able to achieve the same yield, at an even lower complexity by using an easily manufactured permanent magnet arrangement. The designs described are extendible to virtually any combination of length and diameter of the components to be coated.

  15. High yield fabrication of chemically reduced graphene oxide field effect transistors by dielectrophoresis

    International Nuclear Information System (INIS)

    Joung, Daeha; Chunder, A; Zhai, Lei; Khondaker, Saiful I

    2010-01-01

    We demonstrate high yield fabrication of field effect transistors (FET) using chemically reduced graphene oxide (RGO) sheets. The RGO sheets suspended in water were assembled between prefabricated gold source and drain electrodes using ac dielectrophoresis. With the application of a backgate voltage, 60% of the devices showed p-type FET behavior, while the remaining 40% showed ambipolar behavior. After mild thermal annealing at 200 deg. C, all ambipolar RGO FET remained ambipolar with increased hole and electron mobility, while 60% of the p-type RGO devices were transformed to ambipolar. The maximum hole and electron mobilities of the devices were 4.0 and 1.5 cm 2 V -1 s -1 respectively. High yield assembly of chemically derived RGO FET will have significant impact in scaled up fabrication of graphene based nanoelectronic devices.

  16. Epidemiology and impact of Fasciola hepatica exposure in high-yielding dairy herds.

    Science.gov (United States)

    Howell, Alison; Baylis, Matthew; Smith, Rob; Pinchbeck, Gina; Williams, Diana

    2015-09-01

    The liver fluke Fasciola hepatica is a trematode parasite with a worldwide distribution and is the cause of important production losses in the dairy industry. The aim of this observational study was to assess the prevalence of exposure to F. hepatica in a group of high yielding dairy herds, to determine the risk factors and investigate their associations with production and fertility parameters. Bulk milk tank samples from 606 herds that supply a single retailer with liquid milk were tested with an antibody ELISA for F. hepatica. Multivariable linear regression was used to investigate the effect of farm management and environmental risk factors on F. hepatica exposure. Higher rainfall, grazing boggy pasture, presence of beef cattle on farm, access to a stream or pond and smaller herd size were associated with an increased risk of exposure. Univariable regression was used to look for associations between fluke exposure and production-related variables including milk yield, composition, somatic cell count and calving index. Although causation cannot be assumed, a significant (phepatica exposure and estimated milk yield at the herd level, representing a 15% decrease in yield for an increase in F. hepatica exposure from the 25th to the 75th percentile. This remained significant when fertility, farm management and environmental factors were controlled for. No associations were found between F. hepatica exposure and any of the other production, disease or fertility variables. Copyright © 2015 The Authors. Published by Elsevier B.V. All rights reserved.

  17. Neutron yield from thick lead target by the action of high-energy electrons

    International Nuclear Information System (INIS)

    Noga, V.I.; Ranyuk, Yu.N.; Telegin, Yu.N.; Sorokin, P.V.

    1978-01-01

    The results are presented of studying the complete neutron yield from a lead target bombarded by high-energy electrons. Neutrons were recorded by the method of radio-active indicators. The dependence of the neutron yield on the target thickness varying from 0.2 to 8 cm was obtained at the energies of electrons of 230 and 1200 MeV. The neutron yield for the given energies with the target of 6 cm in thickness is in the range of saturation and is 0.1 +-0.03 and 0.65+-0.22 (neutr./MeV.el.), respectively. The neutron angular distributions were measured for different thicknesses of targets at the 201, 230 and 1200 MeV electrons. Within the error limits the angular distributions are isotropic. The dependence of neutron yield on the electron energy was examined for a 3 cm thick target. In the energy range of 100-1200 MeV these values are related by a linear dependence with the proportionality coefficient C=3x10 -4 (neutr./MeV.el.)

  18. The characteristics of high-yield genotype of early-mature mutant lines in barley

    International Nuclear Information System (INIS)

    Chen Xiulan; Han Yuepeng; He Zhentian; Yang Hefeng

    2000-01-01

    The correlation and genetic parameters of eight agronomic traits of 36 early mature mutant lines induced from barley Sunong 9052 were studied by stepwise regression and path analysis. The results showed that: (1) the growing period of early mutants was shortened 2-13 days from that of their parent and the trait of yield had a great mutation range; (2) the number of grain per panicle significantly correlated with the days from sowing to heading; (3) according to direct path coefficients, the main characters related with individual plant-yield were in order of productive panicle per plant > 1000-grain-weight > number of grain per panicle > fertility, the high-yield genotype had more productive panicle and higher 10000-grain-weight, and to increase the yield in the breeding of early mature mutation was to select the lines with more tillers and productive panicles, higher 1000-grain-weight and lower number of grain per panicle; (4) the higher broad-sense heritability and genetic variation coefficient were found in 1000-grain-weight and the days from sowing to heading

  19. High yield cell-free production of integral membrane proteins without refolding or detergents.

    Science.gov (United States)

    Wuu, Jessica J; Swartz, James R

    2008-05-01

    Integral membrane proteins act as critical cellular components and are important drug targets. However, difficulties in producing membrane proteins have hampered investigations of structure and function. In vivo production systems are often limited by cell toxicity, and previous in vitro approaches have required unnatural folding pathways using detergents or lipid solutions. To overcome these limitations, we present an improved cell-free expression system which produces high yields of integral membrane proteins without the use of detergents or refolding steps. Our cell-free reaction activates an Escherichia coli-derived cell extract for transcription and translation. Purified E. coli inner membrane vesicles supply membrane-bound components and the lipid environment required for insertion and folding. Using this system, we demonstrated successful synthesis of two complex integral membrane transporters, the tetracycline pump (TetA) and mannitol permease (MtlA), in yields of 570+/-50 microg/mL and 130+/-30 microg/mL of vesicle-associated protein, respectively. These yields are up to 400 times typical in vivo concentrations. Insertion and folding of these proteins are verified by sucrose flotation, protease digestion, and activity assays. Whereas TetA incorporates efficiently into vesicle membranes with over two-thirds of the synthesized protein being inserted, MtlA yields appear to be limited by insufficient concentrations of a membrane-associated chaperone.

  20. Remote systems requirements of the high-yield lithium injection fusion energy converter concept

    International Nuclear Information System (INIS)

    Walker, P.E.

    1978-01-01

    Remote systems will be required in the high-yield lithium injection fusion energy converter power plant proposed by Lawrence Livermore Laboratory. During inspection operations, viewing of the chamber interior and certain pumps, valve fittings, and welds must be done remotely. Ideas for remote maintenance of laser-beam blast baffles, optics, and target material traps are described. Radioisotope sources, their distributions, and exposure rates at various points in the reactor vicinity are presented

  1. High yield growth of patterned vertically aligned carbon nanotubes using inkjet-printed catalyst.

    Science.gov (United States)

    Beard, James D; Stringer, Jonathan; Ghita, Oana R; Smith, Patrick J

    2013-10-09

    This study reports on the fabrication of vertically aligned carbon nanotubes localized at specific sites on a growth substrate by deposition of a nanoparticle suspension using inkjet printing. Carbon nanotubes were grown with high yield as vertically aligned forests to a length of approximately 400 μm. The use of inkjet printing for catalyst fabrication considerably improves the production rate of vertically aligned patterned nanotube forests compared with conventional patterning techniques, for example, electron beam lithography or photolithography.

  2. Remote systems requirements of the High Yield Lithium Injection Fusion Energy (HYLIFE) converter concept

    International Nuclear Information System (INIS)

    Walker, P.E.

    1978-10-01

    Remote systems will be required in the High Yield Lithium Injection Fusion Energy Converter power plant proposed by Lawrence Livermore Laboratory. During inspection operations, viewing of the chamber interior and certain pumps, valve fittings and welds must be done remotely. Ideas for remote maintenance of laser beam blast baffles, optics, and target material traps are described. Radioisotope sources and their distributions, and exposure rates at various points in the reactor vicinity are presented

  3. Prediction of failure strain and burst pressure in high yield-to-tensile strength ratio linepipe

    International Nuclear Information System (INIS)

    Law, M.; Bowie, G.

    2007-01-01

    Failure pressures and strains were predicted for a number of burst tests as part of a project to explore failure strain in high yield-to-tensile strength ratio linepipe. Twenty-three methods for predicting the burst pressure and six methods of predicting the failure strain are compared with test results. Several methods were identified which gave accurate and reliable estimates of burst pressure. No method of accurately predicting the failure strain was found, though the best was noted

  4. Prediction of failure strain and burst pressure in high yield-to-tensile strength ratio linepipe

    Energy Technology Data Exchange (ETDEWEB)

    Law, M. [Institute of Materials and Engineering Science, Australian Nuclear Science and Technology Organisation (ANSTO), Lucas Heights, NSW (Australia)]. E-mail: mlx@ansto.gov.au; Bowie, G. [BlueScope Steel Ltd., Level 11, 120 Collins St, Melbourne, Victoria 3000 (Australia)

    2007-08-15

    Failure pressures and strains were predicted for a number of burst tests as part of a project to explore failure strain in high yield-to-tensile strength ratio linepipe. Twenty-three methods for predicting the burst pressure and six methods of predicting the failure strain are compared with test results. Several methods were identified which gave accurate and reliable estimates of burst pressure. No method of accurately predicting the failure strain was found, though the best was noted.

  5. Qualidade e produtividade de sementes de canola (Brassica napus após aplicação de dessecantes em pré-colheita Quality and yield of canola (Brassica napus seeds after pre-harvest desiccant application

    Directory of Open Access Journals (Sweden)

    O. Marchiori Jr.

    2002-08-01

    Full Text Available A cultura de canola é indicada nos esquemas de rotação de culturas, bem como para diversificação agrícola e cobertura vegetal do solo no período de inverno na Região Sul do Brasil. Contudo, a colheita mecanizada é uma das operações mais críticas do sistema de produção, uma vez que os frutos do tipo síliqua apresentam maturação desuniforme, gerando grandes perdas de produtividade devido à deiscência natural. O uso de dessecantes químicos permite uma colheita com as síliquas em maturação mais uniforme, porém é importante a manutenção da qualidade do produto obtido. O presente trabalho teve por objetivo avaliar o efeito da aplicação de herbicidas dessecantes na produtividade e na qualidade fisiológica e sanitária das sementes de canola cultivar Hyola 401. Os herbicidas utilizados foram o glufosinato de amônio (0,5 kg ha-1, carfentrazone-ethyl (0,03 kg ha-1, paraquat (0,4 kg ha-1 e diquat (0,3 kg ha-1, mais a testemunha sem aplicação. A qualidade das sementes foi avaliada por meio dos testes de germinação, de envelhecimento acelerado, de condutividade elétrica, de emergência em areia, de velocidade de emergência e de sanidade. A aplicação dos produtos dessecantes permitiu uma antecipação de sete dias na colheita das sementes de canola. A produtividade de sementes não foi afetada pela dessecação. A aplicação do glufosinato de amônio e carfentrazone-ethyl reduziu (PCanola crop is indicated to integrate crop rotation systems, as well as for agricultural diversification and vegetal ground cover during winter in southern Brazil. However, mechanical harvest is critical to crop production, since pods present a non-uniform ripening, leading to great yield losses, due to natural dehiscence. Desiccants are usually applied to provide a more uniform harvest, maintaining the quality of the product. This work aimed to evaluate the effect of desiccant application on productivity and physiological/sanitary quality of

  6. Production costs and fruit yield profitability in the initial harvest of custard apple trees Custo de produção e lucratividade da produção de frutos de inheiras nas primeiras safras

    Directory of Open Access Journals (Sweden)

    Frederico Silva Thé Pontes

    2008-12-01

    Full Text Available The aim of this study was to estimate the production cost and economic indicators associated with the production and sales of fruits from 20 custard apple progenies during the initial five harvests, in order to identify the harvest season from which custard apple exploitation becomes profitable, as well as the most promising progenies from an economic point of view. The fruit yield data upon which the present work was based were obtained during the period from 2001 to 2005, in an experiment that evaluated 20 custard apple half-sibling progenies, under sprinkler irrigation. The progenies were evaluated in a random block design with five replicates and plots consisting of four plants each. The exploitation of custard apple progenies only showed to be a profitable agribusiness after the fourth year. Before that, only A3 and A4 progenies in the second year, and P3 and P11 in the third year provided profitable incomes. Considering the methodological assumptions imposed concerning the time period analysis and the prices as of July 2007, the most important profitability indicators (operating profit, return index and equilibrium price evidenced that the A4 progeny is the most recommended, although other progenies are also highlighted, such as FJ1 and FJ2. As already discussed, the progenies showing the highest average yields of five harvests are not always the most economically recommendable ones.O presente trabalho tem como objetivo estimar o custo de produção e indicadores econômicos, relativos à produção e comercialização de frutos de 20 progênies de pinheiras, nas cinco primeiras safras, visando a identificar a safra a partir da qual a exploração da pinheira é lucrativa e as progênies mais promissoras, do ponto de vista econômico. Os dados de rendimentos de frutos em que se baseou o presente trabalho, foram obtidos no período de 2001 a 2005, em um experimento de avaliação de 20 progênies de meias-irmãs de pinheira, com irriga

  7. Harvesting Atlantic Cod under Climate Variability

    Science.gov (United States)

    Oremus, K. L.

    2016-12-01

    Previous literature links the growth of a fishery to climate variability. This study uses an age-structured bioeconomic model to compare optimal harvest in the Gulf of Maine Atlantic cod fishery under a variable climate versus a static climate. The optimal harvest path depends on the relationship between fishery growth and the interest rate, with higher interest rates dictating greater harvests now at the cost of long-term stock sustainability. Given the time horizon of a single generation of fishermen under assumptions of a static climate, the model finds that the economically optimal management strategy is to harvest the entire stock in the short term and allow the fishery to collapse. However, if the biological growth of the fishery is assumed to vary with climate conditions, such as the North Atlantic Oscillation, there will always be pulses of high growth in the stock. During some of these high-growth years, the growth of the stock and its economic yield can exceed the growth rate of the economy even under high interest rates. This implies that it is not economically optimal to exhaust the New England cod fishery if NAO is included in the biological growth function. This finding may have theoretical implications for the management of other renewable yet exhaustible resources whose growth rates are subject to climate variability.

  8. Photo-oxidation of histidine peptides yields high concentrations of unstable peroxides

    International Nuclear Information System (INIS)

    Policarpio, V.V.; Hawkins, C.L.; Davies, M.J.

    2003-01-01

    Oxidation of proteins by UV, and visible light in the presence of sensitizers, results in side chain modification as well as aggregation and fragmentation. In particular, singlet oxygen has been reported to oxidize Met, Trp, Tyr, Cys and His side chains in a selective manner. In this study the oxidation of histidine and its derivatives, and His-containing peptides is examined using a range of sensitizers, to determine whether peroxides are major intermediates, and the mechanism of formation of these species. Visible light-sensitised oxidation of Gly-His-Gly in the presence of oxygen and rose bengal gives unstable substrate-derived peroxides with the peroxide yield increasing with increasing photolysis time. Similar behaviour was detected with other photosensitizers, though the peroxide yields varied with the sensitizer at identical concentrations with rose bengal > aluminium phthalocyanine > hematoporphyrin IX > zinc phthalocyanine > tetrakisporphine. The peroxide yield was decreased in the presence of azide and enhanced when deuterium oxide was employed as the solvent, consistent with peroxide formation being singlet oxygen mediated. Experiments using anoxic conditions gave low yields of peroxides confirming the oxygen-dependence of these reactions. HPLC analysis showed rapid loss of the parent peptide, with subsequent formation of both stable and unstable products; these are currently being characterized by MS and NMR. Similar behavior has been observed with other His derivatives. The yield of singlet oxygen formed in these reactions has been estimated using a bleaching assay (N, N-dimethyl-4-nitrosoaniline). Quantification of singlet oxygen formation and Gly-His-Gly derived peroxide during rose bengal-mediated photooxidation indicated a conversion efficiency of the initial singlet oxygen into substrate-derived peroxides of ca. 75% indicating that peroxide formation is a highly efficient and major reaction pathway

  9. Catalytic subcritical water liquefaction of flax straw for high yield of furfural

    International Nuclear Information System (INIS)

    Harry, Inibehe; Ibrahim, Hussameldin; Thring, Ron; Idem, Raphael

    2014-01-01

    There is substantial interest in the application of biomass as a renewable fuel or for production of chemicals. Flax straw can be converted into valuable chemicals and biofuels via liquefaction in sub-critical water. In this study, the yield of furfural and the kinetics of flax straw liquefaction under sub-critical water conditions were investigated using a high-pressure autoclave reactor. The liquefaction was conducted in the temperature range of 175–325 °C, pressure of 0.1 MPa–8 MPa, retention time in the range of 0 min–120 min, and flax straw mass fraction (w F ) of 5–20 %. Also, the effect of acid catalysts on furfural yield was studied. The kinetic parameters of flax straw liquefaction were determined using nonlinear regression of the experimental data, assuming second-order kinetics. The apparent activation energy was found to be 27.97 kJ mol −1 while the reaction order was 2.0. The optimum condition for furfural yield was at 250 °C, 6.0 MPa, w F of 5% and 0 retention time after reaching set conditions. An acid catalyst was found to selectively favour furfural yield with 40% flax straw conversion. - Highlights: • Flax straw liquefaction in subcritical water. • Creation of a reaction pathway that can be used to optimized furfural production. • Acid catalyst selectively favoured furfural yield with respect to other liquid products. • At the highest process temperature of 325 °C, a carbon conversion of 40% was achieved. • Activation energy and reaction order was 28 kJ/mol and 2.0 respectively

  10. High Titer and Yields Achieved with Novel, Low-Severity Pretreatment Strategy

    Energy Technology Data Exchange (ETDEWEB)

    2016-03-01

    NREL researchers obtained high concentration sugar syrups in enzymatic hydrolysis that are fermentable to ethanol and other advanced biofuels and intermediate products at high yields. The novel DMR process is simpler and bypasses all severe pretreatment methods, thus reducing the environmental impact. The results are unprecedented. Researchers achieved a high concentration of sugars (230g/L of monomeric sugar and 270 g/L total sugar) and this low toxicity, highly fermentable syrup yielded 86 g/L ethanol (> 90 percent conversion). In addition, the lignin streams from this process can readily be converted to jet or renewable diesel blendstocks through a hydrodeoxygenation step. The NREL-developed, low severity DMR process may potentially replace higher severity chemical pretreatments and associated expensive reactors constructed of exotic alloys with a simpler process, using commercial-scale equipment commonly associated with the pulp and paper industry, to produce high concentration, low toxicity sugar streams and highly reactive lignin streams from non-food renewable biomass for biological and catalytic upgrading to advanced biofuels and chemicals. The simpler DMR process with black liquor recycling could reduce environmental and life-cycle impacts, and repurpose shuttered pulp and paper mills to help revitalize rural economies.

  11. HIGH YIELD AND RAPID SYNTHESES METHODS FOR PRODUCING METALLO-ORGANIC SALTS

    DEFF Research Database (Denmark)

    2005-01-01

    A new method for preparing salts of metal cations and organic acids, especially divalent salts of alkaline earth metal ions from group II of the periodic system and carboxylic acids. The method comprising the use of a high temperature (about 90° or more) and, optionally. high pressure, in order...... to obtain a higher yield, purity and faster reaction speed than obtained with known synthesis methods. In particular, the present invention relates to the production of strontium salts of carboxylic acids. Novel strontium salts are also provided by the present method....

  12. Simple syntheses of 3-substituted indoles and their application for high yield 14C-labelling

    International Nuclear Information System (INIS)

    Schallenberg, J.; Meyer, E.

    1983-01-01

    Methods are described which allow the synthesis of several plant indole alkaloids and their metabolites at different scales. Compounds synthesized include gramine (1) (3-dimethylaminomethylindole) which is directly derived from indole, while its biosynthetic precursors 3-aminomethylindole (3) and 3-methylaminomethylindole (2) as well as indole3-carboxylic acid (7) are synthesized via indole-3-aldehyde (6). Slight changes of the experimental conditions allow syntheses with high yields not only at the molar but also at the μmolar level. This is extremely useful when isotope labelled compounds of high specific radioactivity are required for studies of plant metabolism. (orig.)

  13. Research Advances in High-Yielding Cultivation and Physiology of Super Rice

    Directory of Open Access Journals (Sweden)

    Jing FU

    2012-09-01

    Full Text Available In 1996, China launched a program to breed super rice or super hybrid rice by combining intersubspecific heterosis with ideal plant types. Today, approximately 80 super rice varieties have been released and some of them show high grain yields of 12–21 t/hm2 in field experiments. The main reasons for the high yields of super rice varieties, compared with those of conventional varieties, can be summarized as follows: more spikelets per panicle and larger sink size (number of spikelets per square meter; larger leaf area index, longer duration of green leaf, greater photosynthetic rate, higher lodging resistance, greater dry matter accumulation before the heading stage, greater remobilization of pre-stored carbohydrates from stems and leaves to grains during the grain-filling period; and larger root system and greater root activity. However, there are two main problems in super rice production: poor grain-filling of the later-flowering inferior spikelets (in contrast to earlier-flowering superior spikelets, and low and unstable seed-setting rate. Here, we review recent research advances in the crop physiology of super rice, focusing on biological features, formation of yield components, and population quality. Finally, we suggest further research on crop physiology of super rice.

  14. Broadband Light-Harvesting Molecular Triads with High FRET Efficiency Based on the Coumarin-Rhodamine-BODIPY Platform.

    Science.gov (United States)

    He, Longwei; Zhu, Sasa; Liu, Yong; Xie, Yinan; Xu, Qiuyan; Wei, Haipeng; Lin, Weiying

    2015-08-17

    Broadband capturing and FRET-based light-harvesting molecular triads, CRBs, based on the coumarin-rhodamine-BODIPY platform were rationally designed and synthesized. The absorption band of CRBs starts from blue-green to yellow-orange regions (330-610 nm), covering the strong radiation scope of sunlight. The peripheral coumarin and BODIPY chromophore energy could transfer to the central acceptor rhodamine by a one-step direct way. The energy of the coumarin moiety could also transfer to the BODIPY unit, subsequently transferring to the rhodamine core by two-step sequential ways. Both the efficiencies of the coumarin moiety and the BODIPY unit to the rhodamine core in CRBs, determined by two different ways, are very high. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  15. High yield antibiotic producing mutants of Streptomyces erythreus induced by low energy ion implantation

    Science.gov (United States)

    Yu, Chen; Zhixin, Lin; Zuyao, Zou; Feng, Zhang; Duo, Liu; Xianghuai, Liu; Jianzhong, Tang; Weimin, Zhu; Bo, Huang

    1998-05-01

    Conidia of Streptomyces erythreus, an industrial microbe, were implanted by nitrogen ions with energy of 40-60 keV and fluence from 1 × 10 11 to 5 × 10 14 ions/cm 2. The logarithm value of survival fraction had good linear relationship with the logarithm value of fluence. Some mutants with a high yield of erythromycin were induced by ion implantation. The yield increment was correlated with the implantation fluence. Compared with the mutation results induced by ultraviolet rays, mutation effects of ion implantation were obvious having higher increasing erythromycin potency and wider mutation spectrum. The spores of Bacillus subtilis were implanted by arsenic ions with energy of 100 keV. The distribution of implanted ions was measured by Rutherford Backscattering Spectrometry (RBS) and calculated in theory. The mechanism of mutation induced by ion implantation was discussed.

  16. Glycerol etherification with TBA: high yield to poly-ethers using a membrane assisted batch reactor.

    Science.gov (United States)

    Cannilla, Catia; Bonura, Giuseppe; Frusteri, Leone; Frusteri, Francesco

    2014-05-20

    In this work, a novel approach to obtain high yield to poly-tert-butylglycerolethers by glycerol etherification reaction with tert-butyl alcohol (TBA) is proposed. The limit of this reaction is the production of poly-ethers, which inhibits the formation of poly-ethers potentially usable in the blend with conventional diesel for transportation. The results herein reported demonstrate that the use of a water permselective membrane offers the possibility to shift the equilibrium toward the formation of poly-ethers since the water formed during reaction is continuously and selectively removed from the reaction medium by the recirculation of the gas phase. Using a proper catalyst and optimizing the reaction conditions, in a single experiment, a total glycerol conversion can be reached with a yield to poly-ethers close to 70%, which represents data never before reached using TBA as reactant. The approach here proposed could open up new opportunities for all catalytic reactions affected by water formation.

  17. Responses of Yield Characteristics to High Temperature During Flowering Stage in Hybrid Rice Guodao 6

    Directory of Open Access Journals (Sweden)

    Guan-fu FU

    2008-09-01

    Full Text Available By sowing at different dates during 2005 and 2006 both in paddy fields and greenhouse, a super hybrid rice combination Guodao 6 and a conventional hybrid rice combination Xieyou 46 (as control were used to analyze the differences in heat injury index, seed setting rate, grain yield and its components. Guodao 6 showed more stable yield and spikelet fertility, and lower heat injury index than Xieyou 46. Further studies indicated that the spikelet sterility is positively correlated with the average daily temperature and the maximum daily temperature, with the coefficients of 0.8604 and 0.9850 (P<0.05 respectively in Guodao 6. The effect of high temperature injury on seed setting caused by maximum daily temperature was lower than that by average daily temperature during the grain filling stage.

  18. Nuclear Engineering of Microalgae for High Yield Secretion of Recombinant Proteins

    DEFF Research Database (Denmark)

    Ramos Martinez, Erick Miguel

    biotechnology hosts including safety, metabolic diversity, scalability, sustainability and low production cost. Over the past decades, considerable improvement has been made to express and secrete recombinant proteins in high levels: however current yields are still low. The first research project presented...... to the glycomodules, accumulation of a fusion protein was dramatically increased by up to 12 folds, with the maximum yield of 15 mg L-1. Characterization of the secreted Venus showed the presence of glycosylations and increased resistance to proteolytic degradation. The results from this thesis demonstrate...... the potential of microalgae as a cell factory for secretion of recombinant proteins. The second research project presented in this thesis aimed to establish a new robust method to allow in vivo measurements of metabolic enzyme activities in cyanobacteria, with a hope that the method would facilitate further...

  19. The 'Golden' cLFV channels {mu} {yields} e{gamma} and {mu} {yields} eee - the high-intensity frontier

    Energy Technology Data Exchange (ETDEWEB)

    Kettle, Peter-Raymond, E-mail: peter-raymond.kettle@psi.ch [Paul Scherrer Institut PSI, Laboratory for Particle Physics (Switzerland)

    2013-03-15

    The muon as a laboratory for studying charged lepton-flavour violation (cLFV) has proven to be one of the most sensitive areas to probe for 'New Physics', due to the muon's copious production rate and relatively long lifetime. The search at the intensity frontier with precision-type experiments is complementary to the search for new particles at the high-energy frontier of TeV colliders. Of the three 'golden' muon channels: {mu} {yields} e{gamma}, {mu} {yields} 3e and {mu} {yields} econversion, an overview of the status of the coincidence experiments MEG, together with the latest results, which constitute the most stringent limit to date on this decay and the recently initiated Mu3e experiment, will be given.

  20. Influence of the harvesting time, temperature and drying period on basil (Ocimum basilicum L. essential oil

    Directory of Open Access Journals (Sweden)

    José Luiz S. Carvalho Filho

    Full Text Available Ocimum basilicum L. essential oil with high concentration of linalool is valuable in international business. O. basilicum essential oil is widely used as seasoning and in cosmetic industry. To assure proper essential oil yield and quality, it is crucial to determine which environmental and processing factors are affecting its composition. The goal of our work is to evaluate the effects of harvesting time, temperature, and drying period on the yield and chemical composition of O. basilicum essential oil. Harvestings were performed 40 and 93 days after seedling transplantation. Harvesting performed at 8:00 h and 12:00 h provided higher essential oil yield. After five days drying, the concentration of linalool raised from 45.18% to 86.80%. O. basilicum should be harvested during morning and the biomass dried at 40ºC for five days to obtain linalool rich essential oil.

  1. Homogeneity Analysis of a MEMS-based PZT Thick Film Vibration Energy Harvester Manufacturing Process

    DEFF Research Database (Denmark)

    Lei, Anders; Xu, Ruichao; Borregaard, Louise M.

    2012-01-01

    This paper presents a homogeneity analysis of a high yield wafer scale fabrication of MEMS-based unimorph silicon/PZT thick film vibration energy harvesters aimed towards vibration sources with peak vibrations in the range of around 300Hz. A wafer with a yield of 91% (41/45 devices) has been...

  2. Effect of harvest time on storage loss and sprouting in onion

    Directory of Open Access Journals (Sweden)

    T. SUOJALA

    2008-12-01

    Full Text Available Storability of onion is affected by timing of harvest. However, the optimal time for maximum yield and maximum storability do not necessarily coincide. This study aimed to determine the most suitable harvest time for obtaining a high bulb yield with high quality and storability. Storage experiments were conducted on onions produced in field experiments at a research field and on farms in four years. Results indicate that harvesting could be delayed to 100% maturity, or even longer, without a marked increase in storage loss. In rainy years, late harvest is likely to impair the quality. The incidence of sprouting in shelf life tests varied considerably between years. An early harvest before 50% maturity and a delayed harvest increased the risk of sprouting. It may be concluded that the harvesting of onions for long-term storage can be timed to take place between 50% maturity and even some weeks after complete maturity without a loss in storage quality. Therefore, it is possible to combine high yield and good storage quality.

  3. Metabolic stress and inflammatory response in high-yielding, periparturient dairy cows.

    Science.gov (United States)

    Trevisi, E; Amadori, M; Cogrossi, S; Razzuoli, E; Bertoni, G

    2012-10-01

    Increased disease rates are commonly reported among high-yielding dairy cows in the transition period, extending from 3 weeks before to 3 weeks after calving, and characterized by the occurrence of an inflammatory response in terms of both positive and negative acute phase proteins (APP+ and APP-). To determine the above inflammatory response, the authors had developed the Liver Functionality Index (LFI), which defines the above condition on the basis of some APP- responses (albumin, cholesterol sensu stricto+bilirubin) during the first month of lactation. In this respect, low LFI values are associated to a high inflammatory response and vice versa. The relationship between LFI and inflammatory cytokine response was investigated from day -28 to day +28 with respect to calving in 12 periparturient dairy cows showing the six highest and six lowest LFI values within a cohort of 54 high-yielding dairy cows. The hypothesis being tested was that LFI and APP- on the whole could be used as readout of successful vs. non-successful adaptation to the transition period, with a strong association to disease occurrence. In fact, low LFI cows experienced many more disease cases (13 vs. 3 in high LFI Group) and related drug treatments till day +28. Interleukin-6 (IL-6) serum concentrations were always higher in low LFI cows (Pcows at risk in the transition period toward an improved farm management. Also, our study indicates that disease cases in periparturient, high-yielding dairy cows are correlated with signs of accentuated IL-6 response and other markers of inflammatory phenomena. These likely start in the late lactation period or around dry-off, as suggested by our prepartal data, and proceed at much greater levels after calving. Copyright © 2011 Elsevier Ltd. All rights reserved.

  4. Boron application improves yield of rice cultivars under high temperature stress during vegetative and reproductive stages.

    Science.gov (United States)

    Shahid, Mohammad; Nayak, Amaresh Kumar; Tripathi, Rahul; Katara, Jawahar Lal; Bihari, Priyanka; Lal, Banwari; Gautam, Priyanka

    2018-04-12

    It is reported that high temperatures (HT) would cause a marked decrease in world rice production. In tropical regions, high temperatures are a constraint to rice production and the most damaging effect is on spikelet sterility. Boron (B) plays a very important role in the cell wall formation, sugar translocation, and reproduction of the rice crop and could play an important role in alleviating high temperature stress. A pot culture experiment was conducted to study the effect of B application on high temperature tolerance of rice cultivars in B-deficient soil. The treatments comprised of four boron application treatments viz. control (B0), soil application of 1 kg B ha -1 (B1), soil application of 2 kg B ha -1 (B2), and foliar spray of 0.2% B (Bfs); three rice cultivars viz. Annapurna (HT stress tolerant), Naveen, and Shatabdi (both HT stress susceptible); and three temperature regimes viz. ambient (AT), HT at vegetative stage (HTV), and HT at reproductive stage (HTR). The results revealed that high temperature stress during vegetative or flowering stage reduced grain yield of rice cultivars mainly because of low pollen viability and spikelet fertility. The effects of high temperature on the spikelet fertility and grain filling varied among cultivars and the growth stages of plant when exposed to the high temperature stress. Under high temperature stress, the tolerant cultivar displays higher cell membrane stability, less accumulation of osmolytes, more antioxidant enzyme activities, and higher pollen viability and spikelet fertility than the susceptible cultivars. In the present work, soil application of boron was effective in reducing the negative effects of high temperature both at vegetative and reproductive stages. Application of B results into higher grain yield under both ambient and high temperature condition over control for all the three cultivars; however, more increase was observed for the susceptible cultivar over the tolerant one. The results

  5. Boron application improves yield of rice cultivars under high temperature stress during vegetative and reproductive stages

    Science.gov (United States)

    Shahid, Mohammad; Nayak, Amaresh Kumar; Tripathi, Rahul; Katara, Jawahar Lal; Bihari, Priyanka; Lal, Banwari; Gautam, Priyanka

    2018-04-01

    It is reported that high temperatures (HT) would cause a marked decrease in world rice production. In tropical regions, high temperatures are a constraint to rice production and the most damaging effect is on spikelet sterility. Boron (B) plays a very important role in the cell wall formation, sugar translocation, and reproduction of the rice crop and could play an important role in alleviating high temperature stress. A pot culture experiment was conducted to study the effect of B application on high temperature tolerance of rice cultivars in B-deficient soil. The treatments comprised of four boron application treatments viz. control (B0), soil application of 1 kg B ha-1 (B1), soil application of 2 kg B ha-1 (B2), and foliar spray of 0.2% B (Bfs); three rice cultivars viz. Annapurna (HT stress tolerant), Naveen, and Shatabdi (both HT stress susceptible); and three temperature regimes viz. ambient (AT), HT at vegetative stage (HTV), and HT at reproductive stage (HTR). The results revealed that high temperature stress during vegetative or flowering stage reduced grain yield of rice cultivars mainly because of low pollen viability and spikelet fertility. The effects of high temperature on the spikelet fertility and grain filling varied among cultivars and the growth stages of plant when exposed to the high temperature stress. Under high temperature stress, the tolerant cultivar displays higher cell membrane stability, less accumulation of osmolytes, more antioxidant enzyme activities, and higher pollen viability and spikelet fertility than the susceptible cultivars. In the present work, soil application of boron was effective in reducing the negative effects of high temperature both at vegetative and reproductive stages. Application of B results into higher grain yield under both ambient and high temperature condition over control for all the three cultivars; however, more increase was observed for the susceptible cultivar over the tolerant one. The results suggest

  6. Modulating fluorescence quantum yield of highly concentrated fluorescein using differently shaped green synthesized gold nanoparticles

    International Nuclear Information System (INIS)

    John, Jisha; Thomas, Lincy; Kurian, Achamma; George, Sajan D.

    2016-01-01

    The interaction of dye molecules with differently shaped nanoparticles is of great interest owing to the potential applications in areas of bioimaging, sensing and photodynamic therapy (biology) as well as solar cells (photonics) applications. For such applications, noble metallic nanoparticles are commonly employed to either enhance or quench the luminescence of a nearby fluorophore. However, in most of the studies, the dye concentration is limited to avoid self-quenching. This paper reports the influence of differently shaped gold nanoparticles (spherical, bean and star), prepared via green synthesis, on the emission behavior as well as on the fluorescence quantum yield of fluorescein dye at concentrations for which self-quenching occurs. The emission behavior is probed via laser based steady state fluorescence whereas quantum yield is measured using a dual beam laser based thermal lens technique. The experimentally observed fluorescence quenching with a concomitant increase in thermal lens signal in the vicinity of nanoparticles are explained in terms of nonradiative energy transfer between the donor and the acceptor. Further, the influence of pH of the prepared gold nanofluid on the absorption, emission as well as quantum yield are also accounted. These studies elucidate that even at high concentrations of dye, the gold nanoparticle and its shape clearly influences the optical properties of nearby dye molecules and thus can be exploited for future applications. - Highlights: • Green synthesis of differently shaped gold nanoparticles. • Tailoring emission properties of fluorescein with respect to nanoparticle concentration and shape. • Tailoring the quantum yield of highly concentrated fluorescein with nanoparticles.

  7. High velocity pulse biopsy device enables controllable and precise needle insertion and high yield tissue acquisition.

    Science.gov (United States)

    Schässburger, Kai-Uwe; Paepke, Stefan; Saracco, Ariel; Azavedo, Edward; Ekström, Christina; Wiksell, Hans

    2018-02-01

    Minimally invasive biopsies are a cornerstone of breast cancer management with ultrasound being the preferred guidance modality. New developments in breast cancer management and advances in imaging technologies bring new challenges to current biopsy methodologies. A new biopsy device (NeoNavia® biopsy system, 14 G) was developed. It incorporates a pneumatic needle insertion mechanism that is intended to provide better control of needle progression and enable stepwise insertion without noticeable deformation or displacement of surrounding tissue as visualized under ultrasound. A new method of tissue acquisition was designed to achieve a sampling yield higher than standard methodologies. Needle dynamics was assessed on a specifically designed test bed and sampling performance was compared to a Magnum® biopsy instrument (Bard, Covington, GA, USA) in representative tissue models. The histological quality of samples obtained ex-vivo was evaluated. A pneumatic pulse was measured to accelerate the needle to a maximum velocity of 21.2 ± 2.5 m/s on a stroke length of 2.5 mm, achieving significantly higher acceleration, maximum velocity and power than current biopsy devices. Mean weight of samples obtained by the NeoNavia device were 3.5, 4.6, and 4.3 times higher when sampling was performed in turkey breast, calf thymus and swine pancreas, respectively, as compared to samples obtained with the Magnum instrument. Ex-vivo analysis indicates that the method of tissue acquisition has no apparent negative impact on the histopathologic quality of obtained samples. Copyright © 2018 Associazione Italiana di Fisica Medica. Published by Elsevier Ltd. All rights reserved.

  8. High Yield Chemical Vapor Deposition Growth of High Quality Large-Area AB Stacked Bilayer Graphene

    Science.gov (United States)

    Liu, Lixin; Zhou, Hailong; Cheng, Rui; Yu, Woo Jong; Liu, Yuan; Chen, Yu; Shaw, Jonathan; Zhong, Xing; Huang, Yu; Duan, Xiangfeng

    2012-01-01

    Bernal stacked (AB stacked) bilayer graphene is of significant interest for functional electronic and photonic devices due to the feasibility to continuously tune its band gap with a vertical electrical field. Mechanical exfoliation can be used to produce AB stacked bilayer graphene flakes but typically with the sizes limited to a few micrometers. Chemical vapor deposition (CVD) has been recently explored for the synthesis of bilayer graphene but usually with limited coverage and a mixture of AB and randomly stacked structures. Herein we report a rational approach to produce large-area high quality AB stacked bilayer graphene. We show that the self-limiting effect of graphene growth on Cu foil can be broken by using a high H2/CH4 ratio in a low pressure CVD process to enable the continued growth of bilayer graphene. A high temperature and low pressure nucleation step is found to be critical for the formation of bilayer graphene nuclei with high AB stacking ratio. A rational design of a two-step CVD process is developed for the growth of bilayer graphene with high AB stacking ratio (up to 90 %) and high coverage (up to 99 %). The electrical transport studies demonstrated that devices made of the as-grown bilayer graphene exhibit typical characteristics of AB stacked bilayer graphene with the highest carrier mobility exceeding 4,000 cm2/V·s at room temperature, comparable to that of the exfoliated bilayer graphene. PMID:22906199

  9. Altered Tuber Yield in Genetically Modified High-Amylose and Oil Potato Lines Is Associated With Changed Whole-Plant Nitrogen Economy

    Directory of Open Access Journals (Sweden)

    Fereshteh Pourazari

    2018-03-01

    Full Text Available Breeding for improved crop quality traits can affect non-target traits related to growth and resource use, and these effects may vary in different cultivation conditions (e. g., greenhouse vs. field. The objectives of this study are to investigate the growth and whole-plant nitrogen (N economy of two genetically modified (GM potato lines compared to their non-GM parental varieties and when grown in different cultivation conditions. A high-amylose GM potato line and its parent were grown under field and greenhouse conditions for one growing season in Sweden; and a GM oil potato line and its parent were grown in greenhouse conditions only. Tuber yield, above ground biomass, N uptake efficiency and other plant N economy traits were assessed. In both cultivation conditions, the GM lines produced between 1.5 and two times more tubers as compared with their parents. In the greenhouse, fresh tuber yield and N uptake efficiency were unaffected by the genetic modifications, but the GM-lines produced less tuber biomass per plant-internal N compared to their parents. In the field, the fresh tuber yield was 40% greater in the high-amylose line as compared with its parent; the greater fresh tuber yield in the high-amylose GM line was accomplished by higher water allocation to the harvested tubers, and associated with increased N recovery from soil (+20%, N uptake efficiency (+53%, tuber N content (+20%, and N accumulation (+120% compared with the non-GM parent. The cultivation conditions influenced the yield and N economy. For example, the final fresh above-ground plant biomass and N pool were considerably higher in the greenhouse conditions, whilst the tuber yield was higher in the field conditions. In conclusion, the genetic modification inducing high accumulation of amylose in potato tubers affected several non-target traits related to plant N economy, and increased the plant N uptake and accumulation efficiency of the field-grown plants. Due to strongly

  10. Altered Tuber Yield in Genetically Modified High-Amylose and Oil Potato Lines Is Associated With Changed Whole-Plant Nitrogen Economy.

    Science.gov (United States)

    Pourazari, Fereshteh; Andersson, Mariette; Weih, Martin

    2018-01-01

    Breeding for improved crop quality traits can affect non-target traits related to growth and resource use, and these effects may vary in different cultivation conditions (e. g., greenhouse vs. field). The objectives of this study are to investigate the growth and whole-plant nitrogen (N) economy of two genetically modified (GM) potato lines compared to their non-GM parental varieties and when grown in different cultivation conditions. A high-amylose GM potato line and its parent were grown under field and greenhouse conditions for one growing season in Sweden; and a GM oil potato line and its parent were grown in greenhouse conditions only. Tuber yield, above ground biomass, N uptake efficiency and other plant N economy traits were assessed. In both cultivation conditions, the GM lines produced between 1.5 and two times more tubers as compared with their parents. In the greenhouse, fresh tuber yield and N uptake efficiency were unaffected by the genetic modifications, but the GM-lines produced less tuber biomass per plant-internal N compared to their parents. In the field, the fresh tuber yield was 40% greater in the high-amylose line as compared with its parent; the greater fresh tuber yield in the high-amylose GM line was accomplished by higher water allocation to the harvested tubers, and associated with increased N recovery from soil (+20%), N uptake efficiency (+53%), tuber N content (+20%), and N accumulation (+120%) compared with the non-GM parent. The cultivation conditions influenced the yield and N economy. For example, the final fresh above-ground plant biomass and N pool were considerably higher in the greenhouse conditions, whilst the tuber yield was higher in the field conditions. In conclusion, the genetic modification inducing high accumulation of amylose in potato tubers affected several non-target traits related to plant N economy, and increased the plant N uptake and accumulation efficiency of the field-grown plants. Due to strongly increased

  11. The investigation for attaining the optimal yield of oil shale by integrating high temperature reactors

    International Nuclear Information System (INIS)

    Bhattacharyya, A.T.

    1984-03-01

    This work presents a systemanalytical investigation and shows how far a high temperature reactor can be integrated for achieving the optimal yield of kerogen from oil shale. About 1/3 of the produced components must be burnt out in order to have the required high temperature process heat. The works of IGT show that the hydrogen gasification of oil shale enables not only to reach oil shale of higher quality but also allows to achieve a higher extraction quantity. For this reason a hydro-gasification process has been calculated in this work in which not only hydrogen is used as the gasification medium but also two high temperature reactors are integrated as the source of high temperature heat. (orig.) [de

  12. High-yield oil palm expansion spares land at the expense of forests in the Peruvian Amazon

    International Nuclear Information System (INIS)

    Gutiérrez-Vélez, Víctor H; DeFries, Ruth; Uriarte, María; Lim, Yili; Pinedo-Vásquez, Miguel; Padoch, Christine; Baethgen, Walter; Fernandes, Katia

    2011-01-01

    High-yield agriculture potentially reduces pressure on forests by requiring less land to increase production. Using satellite and field data, we assessed the area deforested by industrial-scale high-yield oil palm expansion in the Peruvian Amazon from 2000 to 2010, finding that 72% of new plantations expanded into forested areas. In a focus area in the Ucayali region, we assessed deforestation for high- and smallholder low-yield oil palm plantations. Low-yield plantations accounted for most expansion overall (80%), but only 30% of their expansion involved forest conversion, contrasting with 75% for high-yield expansion. High-yield expansion minimized the total area required to achieve production but counter-intuitively at higher expense to forests than low-yield plantations. The results show that high-yield agriculture is an important but insufficient strategy to reduce pressure on forests. We suggest that high-yield agriculture can be effective in sparing forests only if coupled with incentives for agricultural expansion into already cleared lands.

  13. Efficiency of radical yield in alkylthymine and alkyluracil by high-LET irradiation

    International Nuclear Information System (INIS)

    Nakagawa, Seiko; Ohta, Nobuaki; Murakami, Takeshi

    2010-01-01

    Penthylthymines and hexyl-, nonyl-, and decyl- uracils were irradiated by C-ion (3.5 GeV) and γ-ray at 77 K. ESR spectra were measured to study radiation induced radicals in the temperature range from 108 to 273 K. A dihydro-5-yl (5-yl) radical formed by H addition to C6 carbon and a secondary alkyl radical by C-H bond fission at the second carbon from the end of the alkyl group were produced at 108 K. A dihydrouracil-6-yl (6-yl) radical formed by H addition to C5 carbon increased with increasing temperature for alkyluracils. The spectral feature obtained by C-ion irradiation was coincident with that by γ-irradiation. Total radical yields increased by alkylation and with increasing the length of alkyl chain. Yields of both 5-yl and secondary alkyl radicals irradiated by C-ion were less than those by γ-ray for penthylthymines and hexyluracil. On the contrary, radical yields were almost the same between ion and γ-ray irradiation for nonyl- and decyl-uracil. Mechanism of radical formation and effect of high-LET irradiation were discussed.

  14. Studies of fission fragment yields via high-resolution γ-ray spectroscopy

    Science.gov (United States)

    Wilson, J. N.; Lebois, M.; Qi, L.; Amador-Celdran, P.; Bleuel, D.; Briz, J. A.; Carroll, R.; Catford, W.; Witte, H. De; Doherty, D. T.; Eloirdi, R.; Georgiev, G.; Gottardo, A.; Goasduff, A.; Hadyñska-Klek, K.; Hauschild, K.; Hess, H.; Ingeberg, V.; Konstantinopoulos, T.; Ljungvall, J.; Lopez-Martens, A.; Lorusso, G.; Lozeva, R.; Lutter, R.; Marini, P.; Matea, I.; Materna, T.; Mathieu, L.; Oberstedt, A.; Oberstedt, S.; Panebianco, S.; Podolyak, Zs.; Porta, A.; Regan, P. H.; Reiter, P.; Rezynkina, K.; Rose, S. J.; Sahin, E.; Seidlitz, M.; Serot, O.; Shearman, R.; Siebeck, B.; Siem, S.; Smith, A. G.; Tveten, G. M.; Verney, D.; Warr, N.; Zeiser, F.; Zielinska, M.

    2018-03-01

    Precise spectroscopic information on the fast neutron induced fission of the 238U(n,f) reaction was recently gained using a new technique which involved coupling of the Miniball high resolution y-ray spectrometer and the LICORNE directional neutron source. The experiment allowed measurement of the isotopic fission yields for around 40 even-even nuclei at an incident neutron energy of around 2 MeV where yield data are very sparse. In addition spectroscopic information on very neutron-rich fission products was obtained. Results were compared to models, both the JEFF-3.1.1 data base and the GEF code, and large discrepancies for the S1 fission mode in the Sn/Mo isotope pair were discovered. This suggests that current models are overestimating the role played by spherical shell effects in fast neutron induced fission. In late 2017 and 2018 the nu-ball hybrid spectrometer will be constructed at the IPN Orsay to perform further experimental investigations with directional neutrons coupled to a powerful hybrid Ge/LaBr3 detector array. This will open up new possibilities for measurements of fission yields for fast-neutron-induced fission using the spectroscopic technique and will be complimentary to other methods being developed.

  15. Studies of fission fragment yields via high-resolution γ-ray spectroscopy

    Directory of Open Access Journals (Sweden)

    Wilson J.N.

    2018-01-01

    Full Text Available Precise spectroscopic information on the fast neutron induced fission of the 238U(n,f reaction was recently gained using a new technique which involved coupling of the Miniball high resolution y-ray spectrometer and the LICORNE directional neutron source. The experiment allowed measurement of the isotopic fission yields for around 40 even-even nuclei at an incident neutron energy of around 2 MeV where yield data are very sparse. In addition spectroscopic information on very neutron-rich fission products was obtained. Results were compared to models, both the JEFF-3.1.1 data base and the GEF code, and large discrepancies for the S1 fission mode in the Sn/Mo isotope pair were discovered. This suggests that current models are overestimating the role played by spherical shell effects in fast neutron induced fission. In late 2017 and 2018 the nu-ball hybrid spectrometer will be constructed at the IPN Orsay to perform further experimental investigations with directional neutrons coupled to a powerful hybrid Ge/LaBr3 detector array. This will open up new possibilities for measurements of fission yields for fast-neutron-induced fission using the spectroscopic technique and will be complimentary to other methods being developed.

  16. The Effect of High Concentrations of Glufosinate Ammonium on the Yield Components of Transgenic Spring Wheat (Triticum aestivum L.) Constitutively Expressing the bar Gene

    OpenAIRE

    Áy, Zoltán; Mihály, Róbert; Cserháti, Mátyás; Kótai, Éva; Pauk, János

    2012-01-01

    We present an experiment done on a bar + wheat line treated with 14 different concentrations of glufosinate ammonium—an effective component of nonselective herbicides—during seed germination in a closed experimental system. Yield components as number of spikes per plant, number of grains per spike, thousand kernel weight, and yield per plant were thoroughly analysed and statistically evaluated after harvesting. We found that a concentration of glufosinate ammonium 5000 times the lethal dose w...

  17. Cacao Cultivation under Diverse Shade Tree Cover Allows High Carbon Storage and Sequestration without Yield Losses.

    Science.gov (United States)

    Abou Rajab, Yasmin; Leuschner, Christoph; Barus, Henry; Tjoa, Aiyen; Hertel, Dietrich

    2016-01-01

    One of the main drivers of tropical forest loss is their conversion to oil palm, soy or cacao plantations with low biodiversity and greatly reduced carbon storage. Southeast Asian cacao plantations are often established under shade tree cover, but are later converted to non-shaded monocultures to avoid resource competition. We compared three co-occurring cacao cultivation systems (3 replicate stands each) with different shade intensity (non-shaded monoculture, cacao with the legume Gliricidia sepium shade trees, and cacao with several shade tree species) in Sulawesi (Indonesia) with respect to above- and belowground biomass and productivity, and cacao bean yield. Total biomass C stocks (above- and belowground) increased fivefold from the monoculture to the multi-shade tree system (from 11 to 57 Mg ha-1), total net primary production rose twofold (from 9 to 18 Mg C ha-1 yr-1). This increase was associated with a 6fold increase in aboveground biomass, but only a 3.5fold increase in root biomass, indicating a clear shift in C allocation to aboveground tree organs with increasing shade for both cacao and shade trees. Despite a canopy cover increase from 50 to 93%, cacao bean yield remained invariant across the systems (variation: 1.1-1.2 Mg C ha-1 yr-1). The monocultures had a twice as rapid leaf turnover suggesting that shading reduces the exposure of cacao to atmospheric drought, probably resulting in greater leaf longevity. Thus, contrary to general belief, cacao bean yield does not necessarily decrease under shading which seems to reduce physical stress. If planned properly, cacao plantations under a shade tree cover allow combining high yield with benefits for carbon sequestration and storage, production system stability under stress, and higher levels of animal and plant diversity.

  18. Grain yield of soybean cultivars using different densities and sowing dates in a high-altitude region of south Brazil

    Directory of Open Access Journals (Sweden)

    Vitor Spader

    2015-07-01

    Full Text Available The study aimed to evaluate the performance of soybean cultivars at different sowing dates and plant densities. Two experiments were carried out at FAPA (Fundação Agrária de Pesquisa Agropecuária [Agrarian Foundation for Agricultural and Cattle Research], located at 25?33’ S latitude, 51?29’ W longitude and with 1.100 meters of altitude in Guarapuava, PR [Paraná], Brazil, in two agricultural harvests (2010/2011 and 2011/2012. The experimental design was in randomized blocks and split plots, in which the sowing dates (10/20, 11/18 and 12/10 were allocated by plot, the densities (250, 350 and 450 thousand plants ha-1 by subplot and the cultivars (BMX Energia, BMX Apolo, BMX Ativa, FPS Júpiter, V_Top, NS 6631, TMG 7161 and BRS Tordilha by sub-subplot. The agronomic characteristics, grain yield and yield components were evaluated. Sowing dates and plant densities affected the agronomic characteristics, grain yield and yield components of soybean. The best sowing dates for lodging-tolerant cultivars are 10/20 and 11/18, and the best densities are 350 and 450 thousand plants ha-1, while lodging-susceptible cultivars respond best for sowing dates of 11/18 and 12/10 and densities from 250 to 350 thousand plants ha-1.

  19. Potential design modifications for the High Yield Lithium Injection Fusion Energy (HYLIFE) reaction chamber

    International Nuclear Information System (INIS)

    Pitts, J.H.; Hovingh, J.; Meier, W.R.; Monsler, M.J.; Powell, E.G.; Walker, P.E.

    1979-01-01

    Generation of electric power from inertial confinement fusion requires a reaction chamber. One promising type, the High Yield Lithium Injection Fusion Energy (HYLIFE) chamber, includes a falling array of liquid lithium jets. These jets act as: (1) a renewable first wall and blanket to shield metal components from x-ray and neutron exposure, (2) a tritium breeder to replace tritium burned during the fusion process, and (3) an absorber and transfer medium for fusion energy. Over 90% of the energy produced in the reaction chamber is absorbed in the lithium jet fall. Design aspects are included

  20. MOCVD Process Technology for Affordable, High-Yield, High-Performance MESFET Structures. MIMIC Phase 3

    Science.gov (United States)

    1993-01-26

    development of large-area deposition for producing high efficiency solar cells."I This earlier work suggested that, with the appropriate modifications, the...using a numerical technique described previously.(2ŗ ) The model simultaneously solves the equations of continuity, motion, differential thermal energy ...Undoped IkeA 1.0 mnn BUBSTRATE Beni rNSIif *A FIGURE 2-4. EPrrAXIAL STRUCTURE FOR BUFFER LEAKAGE TESTS. 350 um 350 um Contact Contact G-20 um , CAP

  1. A Permanent-Magnet Microwave Ion Source for a Compact High-Yield Neutron Generator

    International Nuclear Information System (INIS)

    Waldmann, Ole; Ludewigt, Bernhard

    2010-01-01

    We present recent work on the development of a microwave ion source that will be used in a high-yield compact neutron generator for active interrogation applications. The sealed tube generator will be capable of producing high neutron yields, 5 · 10 11 n/s for D-T and ∼ 1 · 10 10 n/s for D-D reactions, while remaining transportable. We constructed a microwave ion source (2.45 GHz) with permanent magnets to provide the magnetic field strength of 87.5 mT necessary for satisfying the electron cyclotron resonance (ECR) condition. Microwave ion sources can produce high extracted beam currents at the low gas pressures required for sealed tube operation and at lower power levels than previously used RF-driven ion sources. A 100 mA deuterium/tritium beam will be extracted through a large slit (60 · 6 mm 2 ) to spread the beam power over a larger target area. This paper describes the design of the permanent-magnet microwave ion source and discusses the impact of the magnetic field design on the source performance. The required equivalent proton beam current density of 40 mA/cm 2 was extracted at a moderate microwave power of 400 W with an optimized magnetic field.

  2. THE ADAPTATION TEST ON YARDLONG BEAN LINES TOLERANT TO APHIDS AND HIGH YIELD

    Directory of Open Access Journals (Sweden)

    Kuswanto

    2011-06-01

    Full Text Available The adaptation trial was applied to determine the benefits of genotype-environmental inter-action, adaptability and stability of lines. The previous research successfully obtained 8 UB lines which had high yield and tolerant to aphids. These lines belong to plant breeding laboratory of Brawijaya University, which had stability and a high potential can be immediately released to the public. Research was conducted in 2010, dry and rainy season, on 3 locations of yardlong bean, namely Malang, Kediri and Jombang. Randomized Block Design was applied in these locations.Genotype-environment interaction was analyzed with combined analysis of nested design.The adaptability and stability were known from regression analysis based on the stability of Eberhart and Russel. There were 6 stabile lines, namely UB7070P1, UB24089X1, UB606572, UB61318, UB7023J44, and UB715, respectively. They were recommended to be released as new varieties which had pest tolerance and high yield. The UBPU was suitable to be developed in marginal land. The 6 new varieties had registered to Agriculture Department Republic of Indonesia, namely, Brawijaya 1, Brawijaya 3, Brawijaya 4, Bagong 2, Bagong 3 dan Bagong Ungu, respectively.

  3. Neutron temporal diagnostic for high-yield deuterium–tritium cryogenic implosions on OMEGA

    Energy Technology Data Exchange (ETDEWEB)

    Stoeckl, C.; Boni, R.; Ehrne, F.; Forrest, C. J.; Glebov, V. Yu.; Katz, J.; Lonobile, D. J.; Magoon, J.; Regan, S. P.; Shoup, M. J.; Sorce, A.; Sorce, C.; Sangster, T. C.; Weiner, D. [Laboratory for Laser Energetics, University of Rochester, 250 East River Road, Rochester, New York 14623-1299 (United States)

    2016-05-15

    A next-generation neutron temporal diagnostic (NTD) capable of recording high-quality data for the highest anticipated yield cryogenic deuterium–tritium (DT) implosion experiments was recently installed at the Omega Laser Facility. A high-quality measurement of the neutron production width is required to determine the hot-spot pressure achieved in inertial confinement fusion experiments—a key metric in assessing the quality of these implosions. The design of this NTD is based on a fast-rise-time plastic scintillator, which converts the neutron kinetic energy to 350- to 450-nm-wavelength light. The light from the scintillator inside the nose-cone assembly is relayed ∼16 m to a streak camera in a well-shielded location. An ∼200× reduction in neutron background was observed during the first high-yield DT cryogenic implosions compared to the current NTD installation on OMEGA. An impulse response of ∼40 ± 10 ps was measured in a dedicated experiment using hard x-rays from a planar target irradiated with a 10-ps short pulse from the OMEGA EP laser. The measured instrument response includes contributions from the scintillator rise time, optical relay, and streak camera.

  4. High-aspect ratio micro- and nanostructures enabled by photo-electrochemical etching for sensing and energy harvesting applications

    Science.gov (United States)

    Alhalaili, Badriyah; Dryden, Daniel M.; Vidu, Ruxandra; Ghandiparsi, Soroush; Cansizoglu, Hilal; Gao, Yang; Saif Islam, M.

    2018-03-01

    Photo-electrochemical (PEC) etching can produce high-aspect ratio features, such as pillars and holes, with high anisotropy and selectivity, while avoiding the surface and sidewall damage caused by traditional deep reactive ion etching (DRIE) or inductively coupled plasma (ICP) RIE. Plasma-based techniques lead to the formation of dangling bonds, surface traps, carrier leakage paths, and recombination centers. In pursuit of effective PEC etching, we demonstrate an optical system using long wavelength (λ = 975 nm) infra-red (IR) illumination from a high-power laser (1-10 W) to control the PEC etching process in n-type silicon. The silicon wafer surface was patterned with notches through a lithography process and KOH etching. Then, PEC etching was introduced by illuminating the backside of the silicon wafer to enhance depth, resulting in high-aspect ratio structures. The effect of the PEC etching process was optimized by varying light intensities and electrolyte concentrations. This work was focused on determining and optimizing this PEC etching technique on silicon, with the goal of expanding the method to a variety of materials including GaN and SiC that are used in designing optoelectronic and electronic devices, sensors and energy harvesting devices.

  5. Quantitative Genetic Analysis for Yield and Yield Components in Boro Rice (Oryza sativa L.

    Directory of Open Access Journals (Sweden)

    Supriyo CHAKRABORTY

    2010-03-01

    Full Text Available Twenty-nine genotypes of boro rice (Oryza sativa L. were grown in a randomized block design with three replications in plots of 4m x 1m with a crop geometry of 20 cm x 20 cm between November-April, in Regional Agricultural Research Station, Nagaon, India. Quantitative data were collected on five randomly selected plants of each genotype per replication for yield/plant, and six other yield components, namely plant height, panicles/plant, panicle length, effective grains/panicle, 100 grain weight and harvest index. Mean values of the characters for each genotype were used for analysis of variance and covariance to obtain information on genotypic and phenotypic correlation along with coheritability between two characters. Path analyses were carried out to estimate the direct and indirect effects of boro rice�s yield components. The objective of the study was to identify the characters that mostly influence the yield for increasing boro rice productivity through breeding program. Correlation analysis revealed significant positive genotypic correlation of yield/plant with plant height (0.21, panicles/plant (0.53, panicle length (0.53, effective grains/panicle (0.57 and harvest index (0.86. Path analysis based on genotypic correlation coefficients elucidated high positive direct effect of harvest index (0.8631, panicle length (0.2560 and 100 grain weight (0.1632 on yield/plant with a residual effect of 0.33. Plant height and panicles/plant recorded high positive indirect effect on yield/plant via harvest index whereas effective grains/panicle on yield/plant via harvest index and panicle length. Results of the present study suggested that five component characters, namely harvest index, effective grains/plant, panicle length, panicles/plant and plant height influenced the yield of boro rice. A genotype with higher magnitude of these component characters could be either selected from the existing genotypes or evolved by breeding program for genetic

  6. Algorithm for evaluating the effectiveness of a high-rise development project based on current yield

    Science.gov (United States)

    Soboleva, Elena

    2018-03-01

    The article is aimed at the issues of operational evaluation of development project efficiency in high-rise construction under the current economic conditions in Russia. The author touches the following issues: problems of implementing development projects, the influence of the operational evaluation quality of high-rise construction projects on general efficiency, assessing the influence of the project's external environment on the effectiveness of project activities under crisis conditions and the quality of project management. The article proposes the algorithm and the methodological approach to the quality management of the developer project efficiency based on operational evaluation of the current yield efficiency. The methodology for calculating the current efficiency of a development project for high-rise construction has been updated.

  7. Harvest timing and techniques to optimize fiber quality in the Texas High Plains

    Science.gov (United States)

    Production conditions typical to the Texas High Plains region can produce cotton crops with high short fiber and nep content, both of which have a detrimental impact on ring spinning performance. Since Texas now produces nearly 50% of the US cotton crop annually, it is critical that research focuses...

  8. High yielding biomass genotypes of willow (Salix spp.) show differences in below ground biomass allocation

    International Nuclear Information System (INIS)

    Cunniff, Jennifer; Purdy, Sarah J.; Barraclough, Tim J.P.; Castle, March; Maddison, Anne L.; Jones, Laurence E.; Shield, Ian F.; Gregory, Andrew S.; Karp, Angela

    2015-01-01

    Willows (Salix spp.) grown as short rotation coppice (SRC) are viewed as a sustainable source of biomass with a positive greenhouse gas (GHG) balance due to their potential to fix and accumulate carbon (C) below ground. However, exploiting this potential has been limited by the paucity of data available on below ground biomass allocation and the extent to which it varies between genotypes. Furthermore, it is likely that allocation can be altered considerably by environment. To investigate the role of genotype and environment on allocation, four willow genotypes were grown at two replicated field sites in southeast England and west Wales, UK. Above and below ground biomass was intensively measured over two two-year rotations. Significant genotypic differences in biomass allocation were identified, with below ground allocation differing by up to 10% between genotypes. Importantly, the genotype with the highest below ground biomass also had the highest above ground yield. Furthermore, leaf area was found to be a good predictor of below ground biomass. Growth environment significantly impacted allocation; the willow genotypes grown in west Wales had up to 94% more biomass below ground by the end of the second rotation. A single investigation into fine roots showed the same pattern with double the volume of fine roots present. This greater below ground allocation may be attributed primarily to higher wind speeds, plus differences in humidity and soil characteristics. These results demonstrate that the capacity exists to breed plants with both high yields and high potential for C accumulation. - Highlights: • SRC willows are a source of biomass and act as carbon (C) sinks. • Biomass allocation was measured in 4 willow genotypes grown in two UK field sites. • The greatest yielding genotype had the greatest below ground biomass at both sites. • Below ground biomass allocation differed by up to 10% between genotypes and 94% between sites. • Environment e.g. wind

  9. Global modeling of secondary organic aerosol formation from aromatic hydrocarbons: high- vs. low-yield pathways

    Directory of Open Access Journals (Sweden)

    D. K. Henze

    2008-05-01

    Full Text Available Formation of SOA from the aromatic species toluene, xylene, and, for the first time, benzene, is added to a global chemical transport model. A simple mechanism is presented that accounts for competition between low and high-yield pathways of SOA formation, wherein secondary gas-phase products react further with either nitric oxide (NO or hydroperoxy radical (HO2 to yield semi- or non-volatile products, respectively. Aromatic species yield more SOA when they react with OH in regions where the [NO]/[HO2] ratios are lower. The SOA yield thus depends upon the distribution of aromatic emissions, with biomass burning emissions being in areas with lower [NO]/[HO2] ratios, and the reactivity of the aromatic with respect to OH, as a lower initial reactivity allows transport away from industrial source regions, where [NO]/[HO2] ratios are higher, to more remote regions, where this ratio is lower and, hence, the ultimate yield of SOA is higher. As a result, benzene is estimated to be the most important aromatic species with regards to global formation of SOA, with a total production nearly equal that of toluene and xylene combined. Global production of SOA from aromatic sources via the mechanisms identified here is estimated at 3.5 Tg/yr, resulting in a global burden of 0.08 Tg, twice as large as previous estimates. The contribution of these largely anthropogenic sources to global SOA is still small relative to biogenic sources, which are estimated to comprise 90% of the global SOA burden, about half of which comes from isoprene. Uncertainty in these estimates owing to factors ranging from the atmospheric relevance of chamber conditions to model deficiencies result in an estimated range of SOA production from aromatics of 2–12 Tg/yr. Though this uncertainty range affords a significant anthropogenic contribution to global SOA, it is evident from comparisons to recent observations that additional pathways for

  10. MOCVD process technology for affordable, high-yield, high-performance MESFET structures. Phase 3: MIMIC

    Science.gov (United States)

    1993-01-01

    Under the MIMIC Program, Spire has pursued improvements in the manufacturing of low cost, high quality gallium arsenide MOCVD wafers for advanced MIMIC FET applications. As a demonstration of such improvements, Spire was tasked to supply MOCVD wafers for comparison to MBE wafers in the fabrication of millimeter and microwave integrated circuits. In this, the final technical report for Spire's two-year MIMIC contract, we report the results of our work. The main objectives of Spire's MIMIC Phase 3 Program, as outlined in the Statement of Work, were as follows: Optimize the MOCVD growth conditions for the best possible electrical and morphological gallium arsenide. Optimization should include substrate and source qualification as well as determination of the optimum reactor growth conditions; Perform all work on 75 millimeter diameter wafers, using a reactor capable of at least three wafers per run; and Evaluate epitaxial layers using electrical, optical, and morphological tests to obtain thickness, carrier concentration, and mobility data across wafers.

  11. Yield gains of coffee plants from phosphorus fertilization may not be generalized for high density planting

    Directory of Open Access Journals (Sweden)

    Samuel Vasconcelos Valadares

    2014-06-01

    Full Text Available Inconclusive responses of the adult coffee plant to phosphorus fertilization have been reported in the literature, especially when dealing with application of this nutrient in high density planting systems. Thus, this study was carried out for the purpose of assessing the response of adult coffee plants at high planting density in full production (in regard to yield and their biennial cycle/stability to the addition of different sources and application rates of P in the Zona da Mata region of Minas Gerais, Brazil. The experiment with coffee plants of the Catucaí Amarelo 6/30 variety was carried out over four growing seasons. Treatments were arranged in a full factorial design [(4 × 3 + 1] consisting of four P sources (monoammonium phosphate, simple superphosphate, natural reactive rock phosphate from Algeria (Djebel-Onk, and FH 550®, three P rates (100, 200, and 400 kg ha-1 year-1 of P2O5, and an additional treatment without application of the nutrient (0 kg ha-¹ year-¹. A randomized block experimental design was used with three replicates. The four seasons were evaluated as subplots in a split plot experiment. The P contents in soil and leaves increased with increased rates of P application. However, there was no effect from P application on the yield and its biennial cycle/stability regardless of the source used over the four seasons assessed.

  12. Microstructure, mechanical properties and microtexture of friction stir welded S690QL high yield steel

    Energy Technology Data Exchange (ETDEWEB)

    Paillard, Pascal [Institut des Matériaux Jean Rouxel, UMR 6205, Polytech Nantes, Site de la Chantrerie, BP 50609, 44306 Nantes cedex 3 (France); Bertrand, Emmanuel, E-mail: emmanuel.bertrand@univ-nantes.fr [Institut des Matériaux Jean Rouxel, UMR 6205, Polytech Nantes, Site de la Chantrerie, BP 50609, 44306 Nantes cedex 3 (France); Allart, Marion; Benoit, Alexandre [Institut de Recherche Technologique Jules Verne, Chemin du Chaffault, 44340 Bouguenais (France); Ruckert, Guillaume [DCNS Research, Technocampus Ocean, 5 rue de l' Halbrane, 44340 Bouguenais (France)

    2016-12-15

    Two try-out campaigns of friction stir welding (FSW) were performed with different friction parameters to join S690QL high yield strength steel. The welds were investigated at macroscopic and microscopic scales using optical and electronic microscopy and microhardness mapping. Welds of the second campaign exhibit microstructures and mechanical properties in accordance with requirements for service use. Microtexture measurements were carried out in different zones of welds by electron backscattered diffraction (EBSD). It is shown that that texture of the bottom of the weld is similar to that of the base metal, suggesting a diffusion bonding mechanism. Finally, the mechanical properties (tensile strength, resilience, bending) were established on the most promising welds. It is shown that it is possible to weld this high yield strength steel using FSW process with satisfactory geometric, microstructural and mechanical properties. - Highlights: •1000 mm ∗ 400 mm ∗ 8 mm S690QL steel plates are joined by friction stir welding (FSW). •Maximum hardness is reduced by optimization of process parameters. •Various microstructures are formed but no martensite after process optimization. •Texture is modified in mechanically affected zones of the weld. •Texture in the bottom of the weld is preserved, suggesting diffusion bonding.

  13. High-performance Sonitopia (Sonic Utopia): Hyper intelligent Material-based Architectural Systems for Acoustic Energy Harvesting

    Science.gov (United States)

    Heidari, F.; Mahdavinejad, M.

    2017-08-01

    The rate of energy consumption in all over the world, based on reliable statistics of international institutions such as the International Energy Agency (IEA) shows significant increase in energy demand in recent years. Periodical recorded data shows a continuous increasing trend in energy consumption especially in developed countries as well as recently emerged developing economies such as China and India. While air pollution and water contamination as results of high consumption of fossil energy resources might be consider as menace to civic ideals such as livability, conviviality and people-oriented cities. In other hand, automobile dependency, cars oriented design and other noisy activities in urban spaces consider as threats to urban life. Thus contemporary urban design and planning concentrates on rethinking about ecology of sound, reorganizing the soundscape of neighborhoods, redesigning the sonic order of urban space. It seems that contemporary architecture and planning trends through soundscape mapping look for sonitopia (Sonic + Utopia) This paper is to propose some interactive hyper intelligent material-based architectural systems for acoustic energy harvesting. The proposed architectural design system may be result in high-performance architecture and planning strategies for future cities. The ultimate aim of research is to develop a comprehensive system for acoustic energy harvesting which cover the aim of noise reduction as well as being in harmony with architectural design. The research methodology is based on a literature review as well as experimental and quasi-experimental strategies according the paradigm of designedly ways of doing and knowing. While architectural design has solution-focused essence in problem-solving process, the proposed systems had better be hyper intelligent rather than predefined procedures. Therefore, the steps of the inference mechanism of the research include: 1- understanding sonic energy and noise potentials as energy

  14. Evidence of a high density population of harvested leopards in a montane environment.

    Science.gov (United States)

    Chase Grey, Julia N; Kent, Vivien T; Hill, Russell A

    2013-01-01

    Populations of large carnivores can persist in mountainous environments following extensive land use change and the conversion of suitable habitat for agriculture and human habitation in lower lying areas of their range. The significance of these populations is poorly understood, however, and little attention has focussed on why certain mountainous areas can hold high densities of large carnivores and what the conservation implications of such populations might be. Here we use the leopard (Panthera pardus) population in the western Soutpansberg Mountains, South Africa, as a model system and show that montane habitats can support high numbers of leopards. Spatially explicit capture-recapture (SECR) analysis recorded the highest density of leopards reported outside of state-protected areas in sub-Saharan Africa. This density represents a temporally high local abundance of leopards and we explore the explanations for this alongside some of the potential conservation implications.

  15. Evidence of a high density population of harvested leopards in a montane environment.

    Directory of Open Access Journals (Sweden)

    Julia N Chase Grey

    Full Text Available Populations of large carnivores can persist in mountainous environments following extensive land use change and the conversion of suitable habitat for agriculture and human habitation in lower lying areas of their range. The significance of these populations is poorly understood, however, and little attention has focussed on why certain mountainous areas can hold high densities of large carnivores and what the conservation implications of such populations might be. Here we use the leopard (Panthera pardus population in the western Soutpansberg Mountains, South Africa, as a model system and show that montane habitats can support high numbers of leopards. Spatially explicit capture-recapture (SECR analysis recorded the highest density of leopards reported outside of state-protected areas in sub-Saharan Africa. This density represents a temporally high local abundance of leopards and we explore the explanations for this alongside some of the potential conservation implications.

  16. Design of broadband multilayer dichroic coating for a high-efficiency solar energy harvesting system.

    Science.gov (United States)

    Jiachen, Wang; Lee, Sang Bae; Lee, Kwanil

    2015-05-20

    We report on the design and performance of a broadband dichroic coating for a solar energy conversion system. As a spectral beam splitter, the coating facilitates a hybrid system that combines a photovoltaic cell with a thermal collector. When positioned at a 45° angle with respect to incident light, the coating provides high reflectance in the 40-1100 nm and high transmission in the 1200-2000 nm ranges for a photovoltaic cell and a thermal collector, respectively. Numerical simulations show that our design leads to a sharp transition between the reflection and transmission bands, low ripples in both bands, and slight polarization dependence.

  17. Catalytic oxidative conversion of cellulosic biomass to formic acid and acetic acid with exceptionally high yields

    KAUST Repository

    Zhang, Jizhe

    2014-09-01

    Direct conversion of raw biomass materials to fine chemicals is of great significance from both economic and ecological perspectives. In this paper, we report that a Keggin-type vanadium-substituted phosphomolybdic acid catalyst, namely H4PVMo11O40, is capable of converting various biomass-derived substrates to formic acid and acetic acid with high selectivity in a water medium and oxygen atmosphere. Under optimized reaction conditions, H4PVMo11O40 gave an exceptionally high yield of formic acid (67.8%) from cellulose, far exceeding the values achieved in previous catalytic systems. Our study demonstrates that heteropoly acids are generally effective catalysts for biomass conversion due to their strong acidities, whereas the composition of metal addenda atoms in the catalysts has crucial influence on the reaction pathway and the product selectivity. © 2013 Elsevier B.V.

  18. Radiation Hard and High Light Yield Scintillator Search for CMS Phase II Upgrade

    CERN Document Server

    Tiras, Emrah

    2015-01-01

    The CMS detector at the LHC requires a major upgrade to cope with the higher instantaneous luminosity and the elevated radiation levels. The active media of the forward backing hadron calorimeters is projected to be radiation-hard, high light yield scintillation materials or similar alternatives. In this context, we have studied various radiation-hard scintillating materials such as Polyethylene Terephthalate (PET), Polyethylene Naphthalate (PEN), High Efficiency Mirror (HEM) and quartz plates with various coatings. The quartz plates are pure Cerenkov radiators and their radiation hardness has been confirmed. In order to increase the light output, we considered organic and inorganic coating materials such as p-Terphenyl (pTp), Anthracene and Gallium-doped Zinc Oxide (ZnO Ga) that are applied as thin layers on the surface of the quartz plates. Here, we present the results of the related test beam activities, laboratory measurements and recent developments.

  19. High-Yield Lithium-Injection Fusion-Energy (HYLIFE) reactor

    International Nuclear Information System (INIS)

    Blink, J.A.; Hogam, W.J.; Hovingh, J.; Meier, E.R.; Pitts, J.H.

    1985-01-01

    The High-Yield Lithium-Injection Fusion Energy (HYLIFE) concept to convent inertial confinement fusion energy into electric power has undergone intensive research and refinement at LLNL since 1978. This paper reports on the final HYLIFE design, focusing on five major areas: the HYLIFE reaction chamber (which includes neutronics, liquid-metal jet-array hydrocynamics, and structural design), supporting systems, primary steam system and balance of plant, safety and environmental protection, and costs. An annotated bibliography of reports applicable to HYLIFE is also provided. We conclude that HYLIFE is a particularly viable concept for the safe, clean production of electrical energy. The liquid-metal jet array, HYLIFE's key design feature, protects the surrounding structural components from x-rays, fusion fuel-pellet debris, neutron damage and activation, and high temperatures and stresses, allowing the structure to last for the plant's entire 30-year lifetime without being replaced. 127 refs., 18 figs

  20. Illustrating harvest effects on site microclimate in a high-elevation forest stand.

    Science.gov (United States)

    W.B. Fowler; T.D. Anderson

    1987-01-01

    Three-dimensional contour surfaces were drawn for physiologically active radiation (PAR) and air and soil temperatures from measurements taken at a high-elevation site (1450 m) near the crest of the Cascade Range in central Washington. Measurements in a clearcut were compared with measurements from an adjacent uncut stand. Data for 31 days in July and August 1985...

  1. Scalable high-performance algorithm for the simulation of exciton-dynamics. Application to the light harvesting complex II in the presence of resonant vibrational modes

    DEFF Research Database (Denmark)

    Kreisbeck, Christoph; Kramer, Tobias; Aspuru-Guzik, Alán

    2014-01-01

    high-performance many-core platforms using the Open Compute Language (OpenCL). For the light-harvesting complex II (LHC II) found in spinach, the HEOM results deviate from predictions of approximate theories and clarify the time-scale of the transfer-process. We investigate the impact of resonantly...

  2. Establishing a high yielding streptomyces-based cell-free protein synthesis system.

    Science.gov (United States)

    Li, Jian; Wang, He; Kwon, Yong-Chan; Jewett, Michael C

    2017-06-01

    Cell-free protein synthesis (CFPS) has emerged as a powerful platform for applied biotechnology and synthetic biology, with a range of applications in synthesizing proteins, evolving proteins, and prototyping genetic circuits. To expand the current CFPS repertoire, we report here the development and optimization of a Streptomyces-based CFPS system for the expression of GC-rich genes. By developing a streamlined crude extract preparation protocol and optimizing reaction conditions, we were able to achieve active enhanced green fluorescent protein (EGFP) yields of greater than 50 μg/mL with batch reactions lasting up to 3 h. By adopting a semi-continuous reaction format, the EGFP yield could be increased to 282 ± 8 μg/mL and the reaction time was extended to 48 h. Notably, our extract preparation procedures were robust to multiple Streptomyces lividans and Streptomyces coelicolor strains, although expression yields varied. We show that our optimized Streptomyces lividans system provides benefits when compared to an Escherichia coli-based CFPS system for increasing percent soluble protein expression for four Streptomyces-originated high GC-content genes that are involved in biosynthesis of the nonribosomal peptides tambromycin and valinomycin. Looking forward, we believe that our Streptomyces-based CFPS system will contribute significantly towards efforts to express complex natural product gene clusters (e.g., nonribosomal peptides and polyketides), providing a new avenue for obtaining and studying natural product biosynthesis pathways. Biotechnol. Bioeng. 2017;114: 1343-1353. © 2017 Wiley Periodicals, Inc. © 2017 Wiley Periodicals, Inc.

  3. Determinação da escala de coloração da casca e do rendimento em suco do maracujá-amarelo em diferentes épocas de colheita Determination of the peel color scale and juice yield of yellow passion fruits in different harvest seasons

    Directory of Open Access Journals (Sweden)

    Thais Vianna Silva

    2008-12-01

    Full Text Available Este trabalho teve como objetivo determinar uma escala de coloração da casca para identificar o estádio de maturação do maracujá-amarelo e avaliar o rendimento em suco, em diferentes épocas de colheita. Os experimentos foram constituídos de 2 épocas de colheita, contemplando a estação de menor temperatura e menor precipitação de chuvas (EP1-Maio/Setembro, a estação de maior temperatura e precipitação de chuvas (EP2-Outubro/Dezembro e 7 estádios de maturação, com 10 repetições. Os resultados foram avaliados pelo teste de Tukey, a 5% de significância. O parâmetro b de Hunter foi utilizado como o indexador da mudança da coloração amarela. Verificou-se que a mudança de coloração ocorreu no sentido da base para o pedúnculo do fruto. Os frutos da época EP2 apresentaram a maior espessura de casca e o menor rendimento em suco, nos estádios iniciais de amadurecimento. Nos frutos com mais de 65,9% da casca amarelada, a época de colheita não influenciou na espessura da casca e no rendimento em suco, apresentando níveis máximos de suco. Frutos da época EP1 apresentaram o máximo rendimento a partir do estádio com 21,3% de cor amarela.This work had the aim to determinate the peel color scale intended to identify the ripening stage of the yellow passion fruit and evaluate its juice yield in different harvest seasons. The experiments were constituted of 2 harvest seasons and they were accomplished during the period of low temperatures and less precipitation (EP1 - May/September and high temperatures and more precipitation (EP2 - October/December, and seven ripening stages using ten replications. The results were compared by applying the Tukey test at the level of 5% of probability. Hunter b parameter was used as the yellowing index. It was verified that the yellow color progressed from the base to the fruit peduncle. Fruits from the EP2 season presented the lowest juice yield and the highest peel thickness in the early

  4. Rotating-Sleeve Triboelectric-Electromagnetic Hybrid Nanogenerator for High Efficiency of Harvesting Mechanical Energy.

    Science.gov (United States)

    Cao, Ran; Zhou, Tao; Wang, Bin; Yin, Yingying; Yuan, Zuqing; Li, Congju; Wang, Zhong Lin

    2017-08-22

    Currently, a triboelectric nanogenerator (TENG) and an electromagnetic generator (EMG) have been hybridized to effectively scavenge mechanical energy. However, one critical issue of the hybrid device is the limited output power due to the mismatched output impedance between the two generators. In this work, impedance matching between the TENG and EMG is achieved facilely through commercial transformers, and we put forward a highly integrated hybrid device. The rotating-sleeve triboelectric-electromagnetic hybrid nanogenerator (RSHG) is designed by simulating the structure of a common EMG, which ensures a high efficiency in transferring ambient mechanical energy into electric power. The RSHG presents an excellent performance with a short-circuit current of 1 mA and open-circuit voltage of 48 V at a rotation speed of 250 rpm. Systematic measurements demonstrate that the hybrid nanogenerator can deliver the largest output power of 13 mW at a loading resistance of 8 kΩ. Moreover, it is demonstrated that a wind-driven RSHG can light dozens of light-emitting diodes and power an electric watch. The distinctive structure and high output performance promise the practical application of this rotating-sleeve structured hybrid nanogenerator for large-scale energy conversion.

  5. Use of 15N dilution method for screening soybean lines with high yield and high nitrogen fixation ability

    International Nuclear Information System (INIS)

    Li Haixian; Li Xinmin; Danso, S.K.A.

    1998-01-01

    15 N dilution method was used for screening soybean lines with high nitrogen fixation ability. Screened lines 1005, 8502, 2096, 943, 1454 and Dongnong-42 have high nitrogen fixation ability with their % Ndfa of about 70%. 1454 and 1555 are both high yield and high nitrogen fixation lines. The ability of nitrogen fixation was not related to the yield, but related to maturing time. The cultivars with different maturing time have different levels of nitrogen fixation ability. The longer the maturing period is, the greater the ability of nitrogen fixation it has. There were ten cultivars or lines used in the test of 1992 and 1994. Although the weather condition were greatly different between the two years the results of seven cultivars or lines were the same, indicating that nitrogen fixation ability of the soybean is stable with years. Using 15 N dilution method to estimate nitrogen fixation ability of soybean is reliable, however, the % Ndfa of lines 8502 and 2096 increased by 19% in 1994, a rainy year, indicating that a change in % Ndfa with a few varieties maybe caused by weather

  6. Future consequences of decreasing marginal production efficiency in the high-yielding dairy cow.

    Science.gov (United States)

    Moallem, U

    2016-04-01

    The objectives were to examine the gross and marginal production efficiencies in high-yielding dairy cows and the future consequences on dairy industry profitability. Data from 2 experiments were used in across-treatments analysis (n=82 mid-lactation multiparous Israeli-Holstein dairy cows). Milk yields, body weights (BW), and dry matter intakes (DMI) were recorded daily. In both experiments, cows were fed a diet containing 16.5 to 16.6% crude protein and net energy for lactation (NEL) at 1.61 Mcal/kg of dry matter (DM). The means of milk yield, BW, DMI, NEL intake, and energy required for maintenance were calculated individually over the whole study, and used to calculate gross and marginal efficiencies. Data were analyzed in 2 ways: (1) simple correlation between variables; and (2) cows were divided into 3 subgroups, designated low, moderate, and high DMI (LDMI, MDMI, and HDMI), according to actual DMI per day: ≤ 26 kg (n=27); >26 through 28.2 kg (n=28); and >28.2 kg (n=27). The phenotypic Pearson correlations among variables were analyzed, and the GLM procedure was used to test differences between subgroups. The relationships between milk and fat-corrected milk yields and the corresponding gross efficiencies were positive, whereas BW and gross production efficiency were negatively correlated. The marginal production efficiency from DM and energy consumed decreased with increasing DMI. The difference between BW gain as predicted by the National Research Council model (2001) and the present measurements increased with increasing DMI (r=0.68). The average calculated energy balances were 1.38, 2.28, and 4.20 Mcal/d (standard error of the mean=0.64) in the LDMI, MDMI, and HDMI groups, respectively. The marginal efficiency for milk yields from DMI or energy consumed was highest in LDMI, intermediate in MDMI, and lowest in HDMI. The predicted BW gains for the whole study period were 22.9, 37.9, and 75.8 kg for the LDMI, MDMI, and HDMI groups, respectively. The

  7. Harnessing the respiration machinery for high-yield production of chemicals in metabolically engineered Lactococcus lactis

    DEFF Research Database (Denmark)

    Liu, Jianming; Wang, Zhihao; Kandasamy, Vijayalakshmi

    2017-01-01

    on metabolically engineered Lactococcus lactis strains to optimize the production of acetoin and (R,R)−2,3-butanediol (R-BDO). In the absence of an external electron acceptor, a surplus of two NADH per acetoin molecule is produced. We found that a fully activated respiration was able to efficiently regenerate NAD......+, and a high titer of 371 mM (32 g/L) of acetoin was obtained with a yield of 82% of the theoretical maximum. Subsequently, we extended the metabolic pathway from acetoin to R-BDO by introducing the butanediol dehydrogenase gene from Bacillus subtilis. Since one mole of NADH is consumed when acetoin...... is converted into R-BDO per mole, only the excess of NADH needs to be oxidized via respiration. Either by fine-tuning the respiration capacity or by using a dual-phase fermentation approach involving a switch from fully respiratory to non-respiratory conditions, we obtained 361 mM (32 g/L) R-BDO with a yield...

  8. Monte carlo calculation of energy deposition and ionization yield for high energy protons

    International Nuclear Information System (INIS)

    Wilson, W.E.; McDonald, J.C.; Coyne, J.J.; Paretzke, H.G.

    1985-01-01

    Recent calculations of event size spectra for neutrons use a continuous slowing down approximation model for the energy losses experienced by secondary charged particles (protons and alphas) and thus do not allow for straggling effects. Discrepancies between the calculations and experimental measurements are thought to be, in part, due to the neglect of straggling. A tractable way of including stochastics in radiation transport calculations is via the Monte Carlo method and a number of efforts directed toward simulating positive ion track structure have been initiated employing this technique. Recent results obtained with our updated and extended MOCA code for charged particle track structure are presented here. Major emphasis has been on calculating energy deposition and ionization yield spectra for recoil proton crossers since they are the most prevalent event type at high energies (>99% at 14 MeV) for small volumes. Neutron event-size spectra can be obtained from them by numerical summing and folding techniques. Data for ionization yield spectra are presented for simulated recoil protons up to 20 MeV in sites of diameters 2-1000 nm

  9. Mass production of multi-wall carbon nanotubes by metal dusting process with high yield

    International Nuclear Information System (INIS)

    Ghorbani, H.; Rashidi, A.M.; Rastegari, S.; Mirdamadi, S.; Alaei, M.

    2011-01-01

    Research highlights: → Synthesis of carbon nanotubes over Fe-Ni nanoparticles supported alloy 304L. → Production of carbon nanotubes with high yield (700-1000%) and low cost catalyst. → Optimum growth condition is CO/H 2 = 1/1, 100 cm 3 /min, at 620 o C under long term repetitive thermal cycling. → Possibility of the mass production by metal dusting process with low cost. -- Abstract: Carbon nanotube materials were synthesized over Fe-Ni nanoparticles generated during disintegration of the surface of alloy 304L under metal dusting environment. The metal dusting condition was simulated and optimized through exposing stainless steel samples during long term repetitive thermal cycling in CO/H 2 = 1/1, total gas flow rate 100 cm 3 /min, at 620 o C for 300 h. After reaction, surface morphology of the samples and also carbonaceous deposition which had grown on sample surfaces were examined by stereoscopy, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Results revealed that multi-wall carbon nanotubes could be formed over nanocatalyst generated on the alloy surface by exploiting metal dusting process. By optimization of reaction parameters the yields of carbon nanotube materials obtained were 700-1000%. Also it has been shown herein that the amount of carbon nanotube materials remarkably increases when the reaction time is extended up to 300 h, indicating a possibility of the mass production by this easy method.

  10. Improvement on the light yield of a high-Z inorganic scintillator GSO(Ce)

    CERN Document Server

    Kamae, T; Isobe, N; Kokubun, M; Kubota, A; Osone, S; Takahashi, T; Tsuchida, N; Ishibashi, H

    2002-01-01

    Cerium-doped gadolinium silicic dioxide crystal, GSO(Ce), is a high-Z non-hydroscopic scintillator that gives higher light yield than BGO, and can potentially replace NaI(Tl), CsI(Tl) and BGO in many applications. Its production cost, however, has been substantially higher than any of them, while its energy resolution has been worse than that of NaI(Tl) or CsI(Tl). The merit did not overcome these deficiencies except in limited applications. We developed a low background phoswich counter (the well-type phoswich counter) for the Hard X-ray Detector of the Astro-E project based on GSO scintillator. In the developmental work, we have succeeded in improving the light yield of GSO(Ce) by 40-50%. For energies above 500 keV, a large GSO(Ce) crystal (4.5 cmx4.5phi cm) now gives energy resolution comparable to or better than the best NaI(Tl) when read out with a phototube. With a small GSO(Ce) crystal (5x5x5 mm sup 3) and a photodiode, an energy resolution comparable to or better than the best CsI(Tl) has been obtaine...

  11. Scintillation and ionization yields produced by α-particles in high-density gaseous xenon

    International Nuclear Information System (INIS)

    Kusano, H.; Ishikawa, T.; Lopes, J.A.M.; Miyajima, M.; Shibamura, E.; Hasebe, N.

    2012-01-01

    The average numbers of scintillation photons and liberated electrons produced by 5.49-MeV α-particles were measured in high-density gaseous xenon. The density range is 0.12–1.32 g/cm 3 for scintillation measurements at zero electric field, and 0.12–1.03 g/cm 3 for the scintillation and ionization measurements under various electric fields. The density dependence of scintillation yield at zero electric field was observed. The W s -value, which is defined as the average energy expended per photon, increases with density and becomes almost constant in the density range above 1.0 g/cm 3 . Anti-correlations between average numbers of scintillation photons and liberated electrons were found to vary with density. It was also found that the total number of scintillation photons and liberated electrons decreases with increasing density. Several possible reasons for the variation in scintillation and ionization yields with density are discussed.

  12. High salinity relay as a post-harvest processing method for reducing Vibrio vulnificus levels in oysters (Crassostrea virginica).

    Science.gov (United States)

    Audemard, Corinne; Kator, Howard I; Reece, Kimberly S

    2018-08-20

    High salinity relay of Eastern oysters (Crassostrea virginica) was evaluated as a post-harvest processing (PHP) method for reducing Vibrio vulnificus. This approach relies on the exposure of oysters to natural high salinity waters and preserves a live product compared to previously approved PHPs. Although results of prior studies evaluating high salinity relay as a means to decrease V. vulnificus levels were promising, validation of this method as a PHP following approved guidelines is required. This study was designed to provide data for validation of this method following Food and Drug Administration (FDA) PHP validation guidelines. During each of 3 relay experiments, oysters cultured from 3 different Chesapeake Bay sites of contrasting salinities (10-21 psu) were relayed without acclimation to high salinity waters (31-33 psu) for up to 28 days. Densities of V. vulnificus and densities of total and pathogenic Vibrio parahaemolyticus (as tdh positive strains) were measured using an MPN-quantitative PCR approach. Overall, 9 lots of oysters were relayed with 6 exhibiting initial V. vulnificus >10,000/g. As recommended by the FDA PHP validation guidelines, these lots reached both the 3.52 log reduction and the levels ranged from 2 to 61% after 28 days of relay. Although the identification of the factors implicated in oyster mortality will require further examination, this study strongly supports the validation of high salinity relay as an effective PHP method to reduce levels of V. vulnificus in oysters to endpoint levels approved for human consumption. Copyright © 2018 Elsevier B.V. All rights reserved.

  13. High quantum yield graphene quantum dots decorated TiO_2 nanotubes for enhancing photocatalytic activity

    International Nuclear Information System (INIS)

    Qu, Ailan; Xie, Haolong; Xu, Xinmei; Zhang, Yangyu; Wen, Shengwu; Cui, Yifan

    2016-01-01

    Highlights: • High concentration yellow GQDs and TiO_2 nanotubes were achieved by a simple and green method. • High quantum yield GQDs enhanced the photodegradation capacity of TiO_2 nanotube. • The catalytic performance of GQDs/TiO_2 depends on the GQDs loading. • The improved photocatalytic activity of GQDs/TiO_2 was attributed to three aspects. - Abstract: Graphene quantum dots (GQDs) with high quantum yield (about 23.6% at an excitation wavelength of 320 nm) and GQDs/TiO_2 nanotubes (GQDs/TiO_2 NTs) composites were achieved by a simple hydrothermal method at low temperature. Photoluminescence characterization showed that the GQDs exhibited the down-conversion PL features at excitation from 300 to 420 nm and up-conversion photoluminescence in the range of 600–800 nm. The photocatalytic activity of prepared GQDs/TiO_2 NTs composites on the degradation of methyl orange (MO) was significantly enhanced compared with that of pure TiO_2 nanotubes (TiO_2 NTs). For the composites coupling with 1.5%, 2.5% and 3.5% GQDs, the degradation of MO after 20 min irradiation under UV–vis light irradiation (λ = 380–780 nm) were 80.52%, 94.64% and 51.91%, respectively, which are much higher than that of pure TiO_2 NTs (35.41%). It was inferred from the results of characterization that the improved photocatalytic activity of the GQDs/TiO_2 NTs composites was attributed to the synergetic effect of up-conversion properties of the GQDs, enhanced visible light absorption and efficient separation of photogenerated electron-holes of the GQDs/TiO_2 composite.

  14. Manthar-03: a high-yielding cultivar of wheat released for general cultivation in Southern Punjab

    International Nuclear Information System (INIS)

    Hussain, M.; Akhtar, L.H.; Nasim, M.

    2010-01-01

    We report the release of a new wheat variety Manthar-03. 'Manthar-03' is a high yielding and rust resistant variety of bread wheat with erect growth habit. It was released in the year 2003 as a general purpose variety. Manthar-03 is a selection from CIMMYT material (Entry No. 42 of 29 International Bread Wheat Screening Nursery) made at Regional Agricultural Research Institute (RARI), Bahawalpur during 1996-97. This strain has the famous CIMMYT line 'Kauz' in its parentage (KAUZ//ALTAR 84/AOS). Its pedigree is CM11163-6M-20Y-10M- 0M-0B. It is a more adapted and a high yielder. Genetically, this strain differs from existing commercial cultivars of Punjab. Resistance against leaf rust (5MRMS to 10MR), RRI value of 6.7 and 7.6 for leaf rust and ACI values of 3.4 and 0.7 for leaf rust) and high yield potential (6300 kg ha-1 ) are the major attributes of Manthar-03 that make it a superior variety for its target regions. Manthar-03 is tolerant to wheat aphid and Helicoverpa armigera. The thousand seed weight of this variety is 40-44 g. Seed is amber in color and contains 12.97% protein, 8.2% dry gluten and 1.55% ash. It has good chapati making quality. Plant type of Manthar-03 is erect with plant height 94 cm and droopy flag leaves. It is lodging resistant. It completes heading in 98 days and matures in 142 days. Manthar-03 performs better when planted from 15, November to 1, December, keeping 125 kg ha/sup -1/ seed rate and 125-85-50 kg NPK ha/sup -1/ are applied. (author)

  15. The yield of high-detail radiographic skeletal surveys in suspected infant abuse

    International Nuclear Information System (INIS)

    Barber, Ignasi; Perez-Rossello, Jeannette M.; Kleinman, Paul K.; Wilson, Celeste R.

    2015-01-01

    Skeletal surveys are routinely performed in cases of suspected child abuse, but there are limited data regarding the yield of high-detail skeletal surveys in infants. To determine the diagnostic yield of high-detail radiographic skeletal surveys in suspected infant abuse. We reviewed the high-detail American College of Radiology standardized skeletal surveys performed for suspected abuse in 567 infants (median: 4.4 months, SD 3.47; range: 4 days-12 months) at a large urban children's hospital between 2005 and 2013. Skeletal survey images, radiology reports and medical records were reviewed. A skeletal survey was considered positive when it showed at least one unsuspected fracture. In 313 of 567 infants (55%), 1,029 definite fractures were found. Twenty-one percent (119/567) of the patients had a positive skeletal survey with a total of 789 (77%) unsuspected fractures. Long-bone fractures were the most common injuries, present in 145 children (26%). The skull was the site of fracture in 138 infants (24%); rib cage in 77 (14%), clavicle in 24 (4.2%) and uncommon fractures (including spine, scapula, hands and feet and pelvis) were noted in 26 infants (4.6%). Of the 425 infants with neuroimaging, 154 (36%) had intracranial injury. No significant correlation between positive skeletal survey and associated intracranial injury was found. Scapular fractures and complex skull fractures showed a statistically significant correlation with intracranial injury (P = 0.029, P = 0.007, respectively). Previously unsuspected fractures are noted on skeletal surveys in 20% of cases of suspected infant abuse. These data may be helpful in the design and optimization of global skeletal imaging in this vulnerable population. (orig.)

  16. The yield of high-detail radiographic skeletal surveys in suspected infant abuse

    Energy Technology Data Exchange (ETDEWEB)

    Barber, Ignasi [Hospital Vall d' Hebron, Universitat Autonoma de Barcelona, Pediatric Radiology Department, Barcelona (Spain); Perez-Rossello, Jeannette M.; Kleinman, Paul K. [Boston Children' s Hospital, Radiology Department, Boston, MA (United States); Wilson, Celeste R. [Boston Children' s Hospital, Division of General Pediatrics, Boston, MA (United States)

    2014-07-06

    Skeletal surveys are routinely performed in cases of suspected child abuse, but there are limited data regarding the yield of high-detail skeletal surveys in infants. To determine the diagnostic yield of high-detail radiographic skeletal surveys in suspected infant abuse. We reviewed the high-detail American College of Radiology standardized skeletal surveys performed for suspected abuse in 567 infants (median: 4.4 months, SD 3.47; range: 4 days-12 months) at a large urban children's hospital between 2005 and 2013. Skeletal survey images, radiology reports and medical records were reviewed. A skeletal survey was considered positive when it showed at least one unsuspected fracture. In 313 of 567 infants (55%), 1,029 definite fractures were found. Twenty-one percent (119/567) of the patients had a positive skeletal survey with a total of 789 (77%) unsuspected fractures. Long-bone fractures were the most common injuries, present in 145 children (26%). The skull was the site of fracture in 138 infants (24%); rib cage in 77 (14%), clavicle in 24 (4.2%) and uncommon fractures (including spine, scapula, hands and feet and pelvis) were noted in 26 infants (4.6%). Of the 425 infants with neuroimaging, 154 (36%) had intracranial injury. No significant correlation between positive skeletal survey and associated intracranial injury was found. Scapular fractures and complex skull fractures showed a statistically significant correlation with intracranial injury (P = 0.029, P = 0.007, respectively). Previously unsuspected fractures are noted on skeletal surveys in 20% of cases of suspected infant abuse. These data may be helpful in the design and optimization of global skeletal imaging in this vulnerable population. (orig.)

  17. The cost of silage harvest and transport systems for herbaceous crops

    Energy Technology Data Exchange (ETDEWEB)

    Turhollow, A.; Downing, M. [Oak Ridge National Lab., TN (United States); Butler, J. [Butler (James), Tifton, GA (United States)

    1996-12-31

    Some of the highest yielding herbaceous biomass crops are thick- stemmed species. Their relatively high moisture content necessitates they be handled and stored as silage rather than hay bales or modules. This paper presents estimated costs of harvesting and transporting herbaceous crops as silage. Costs are based on an engineering- economic approach. Equipment costs are estimated by combining per hour costs with the hours required to complete the operation. Harvest includes severing, chopping, and blowing stalks into a wagon or truck.

  18. High yield growth of uniform ZnS nanospheres with strong photoluminescence properties

    International Nuclear Information System (INIS)

    Li, Yuan; Li, Qing; Wu, Huijie; Zhang, Jin; Lin, Hua; Nie, Ming; Zhang, Yu

    2013-01-01

    Graphical abstract: High-yield ZnS nanospheres with an average diameter of 80 nm were fabricated successfully in aqueous solution at 100 °C by the assistance of surfactant PVP. It was found that PVP plays a crucial role in the formation of uniform ZnS nanospheres. A possible self-assembling growth mechanism was proposed. The UV–vis spectrum indicates that the as-prepared ZnS nanospheres exhibit a dramatic blue-shift. PL spectrum reveals that the ZnS nanospheres have a strong visible emission peak centered at 516 nm with excitation light of 400 nm. Highlights: ► High-yield ZnS nanospheres were generated conveniently in aqueous solution. ► The amount of surfactant PVP plays a crucial role on the morphology and size of the products. ► A tentative explanation for the growth mechanism of ZnS nanospheres was proposed. ► The UV–vis spectrum indicated that the sample exhibits a dramatic blue-shift. ► PL spectrum reveals that ZnS nanospheres have a strong visible emission peak centered at 516 nm with excitation light of 400 nm. - Abstract: High yield ZnS nanospheres were generated conveniently in aqueous solution with the assistance of surfactant polyvinyl pyrrolidone (PVP). The products were characterized by XRD, EDX, XPS, FESEM, TEM and HRTEM. The as-prepared ZnS nanospheres were uniform with an average diameter of 80 nm. The role of PVP in the forming of ZnS nanospheres was investigated. The results indicated that surfactant PVP plays a crucial role on the morphology and size of the products. Moreover, a tentative explanation for the growth mechanism of ZnS nanospheres was proposed. UV–vis and PL absorption spectrum were used to investigate the optical properties of ZnS nanospheres. The UV–vis spectrum indicated that the sample exhibits a dramatic blue-shift. PL spectrum reveals that ZnS nanospheres have a strong visible emission peak centered at 516 nm with excitation light of 400 nm.

  19. Monte Carlo simulation for neutron yield produced by bombarding thick targets with high energy heavy ions

    Energy Technology Data Exchange (ETDEWEB)

    Oranj, Leila Mokhtari; Oh, Joo Hee; Yoon, Moo Hyun; Lee, Hee Seock [POSTECH, Pohang (Korea, Republic of)

    2013-04-15

    One of radiation shielding issues at heavy-ion accelerator facilities is to estimate neutron production by primary heavy ions. A few Monte Carlo transport codes such as FLUKA and PHITS can work with primary heavy ions. Recently IBS/RISP((Rare Isotope Science Project) started to design a high-energy, high-power rare isotope accelerator complex for nuclear physics, medical and material science and applications. There is a lack of experimental and simulated data about the interaction of major beam, {sup 238}U with materials. For the shielding design of the end of first accelerating section section, we calculate a differential neutron yield using the FLUKA code for the interaction of 18.5 MeV/u uranium ion beam with thin carbon stripper of 1.3 μm). The benchmarking studies were also done to prove the yield calculation for 400 MeV/n {sup 131}Xe and other heavy ions. In this study, the benchmarking for Xe-C, Xe-Cu, Xe-Al, Xe-Pb and U-C, other interactions were performed using the FLUKA code. All of results show that the FLUKA can evaluate the heavy ion induced reaction with good uncertainty. For the evaluation of neutron source term, the calculated neutron yields are shown in Fig. 2. The energy of Uranium ion beam is only 18.5 MeV/u, but the energy of produced secondary neutrons was extended over 100 MeV. So the neutron shielding and the damage by those neutrons is expected to be serious. Because of thin stripper, the neutron intensity at forward direction was high. But the the intensity of produced secondary photons was relatively low and mostly the angular property was isotropic. For the detail shielding design of stripper section of RISP rare istope accelerator, the benchmarking study and preliminary evaluation of neutron source term from uranium beam have been carried out using the FLUKA code. This study is also compared with the evaluation results using the PHITS code performed coincidently. Both studies shows that two monte carlo codes can give a good results for

  20. Combine Harvester Simulator

    DEFF Research Database (Denmark)

    Vilmann, Ole; Sørlie, James Arnold

    1999-01-01

    A simulator for training pilots in the operation of a modern high-tech combine harvester is presented. The new simulator application is based on DMI´s well-known DMS maritime simulator architecture. Two major challenges have been encountered in the development of the simulator: 1) interfacing the...

  1. Interrelations between Herbage Yield, α-Tocopherol, β-Carotene, Lutein, Protein, and Fiber in Non-Leguminous Forbs, Forage Legumes, and a Grass−Clover Mixture as Affected by Harvest Date

    DEFF Research Database (Denmark)

    Elgersma, Anjo; Søegaard, Karen; Jensen, Søren Krogh

    2015-01-01

    , protein and fiber contents and analyze the effect of harvest date. We hypothesized that interrelations would be similar across investigated forage species. Four nonleguminous forbs: salad burnet (Sanguisorba minor), caraway (Carum carvi), chicory (Cichorium intybus), and ribwort plantain (Plantago...

  2. BRS FC402: high-yielding common bean cultivar with carioca grain, resistance to anthracnose and fusarium wilt

    Directory of Open Access Journals (Sweden)

    Leonardo Cunha Melo

    2016-12-01

    Full Text Available BRS FC402 is a common bean cultivar of the carioca-grain group with commercial grain quality, suitable for cultivation in 21 Brazilian states. Cultivar has a normal cycle (85-94 days, high yield potential (4479 kg ha-1, 10.1% higher mean yield than the controls (2462 kg ha-1 and resistance to fusarium wilt and anthracnose.

  3. BRS 369RF and BRS 370RF: Glyphosate tolerant, high-yielding upland cotton cultivars for central Brazilian savanna

    Directory of Open Access Journals (Sweden)

    Camilo de Lelis Morello

    2015-12-01

    Full Text Available BRS 369RF and BRS 370RF were developed by the EMBRAPA as a part of efforts to create high-yielding germplasm with combinations of transgenic traits. BRS 369RF and BRS 370RF are midseason cultivars and have yield stability, adaptation to the central Brazilian savanna, good fiber quality and tolerance to glyphosate herbicide.

  4. Molecular signature of high yield (growth influenza a virus reassortants prepared as candidate vaccine seeds.

    Directory of Open Access Journals (Sweden)

    Manojkumar Ramanunninair

    Full Text Available Human influenza virus isolates generally grow poorly in embryonated chicken eggs. Hence, gene reassortment of influenza A wild type (wt viruses is performed with a highly egg adapted donor virus, A/Puerto Rico/8/1934 (PR8, to provide the high yield reassortant (HYR viral 'seeds' for vaccine production. HYR must contain the hemagglutinin (HA and neuraminidase (NA genes of wt virus and one to six 'internal' genes from PR8. Most studies of influenza wt and HYRs have focused on the HA gene. The main objective of this study is the identification of the molecular signature in all eight gene segments of influenza A HYR candidate vaccine seeds associated with high growth in ovo.The genomes of 14 wt parental viruses, 23 HYRs (5 H1N1; 2, 1976 H1N1-SOIV; 2, 2009 H1N1pdm; 2 H2N2 and 12 H3N2 and PR8 were sequenced using the high-throughput sequencing pipeline with big dye terminator chemistry.Silent and coding mutations were found in all internal genes derived from PR8 with the exception of the M gene. The M gene derived from PR8 was invariant in all 23 HYRs underlining the critical role of PR8 M in high yield phenotype. None of the wt virus derived internal genes had any silent change(s except the PB1 gene in X-157. The highest number of recurrent silent and coding mutations was found in NS. With respect to the surface antigens, the majority of HYRs had coding mutations in HA; only 2 HYRs had coding mutations in NA.In the era of application of reverse genetics to alter influenza A virus genomes, the mutations identified in the HYR gene segments associated with high growth in ovo may be of great practical benefit to modify PR8 and/or wt virus gene sequences for improved growth of vaccine 'seed' viruses.

  5. Differential gene expression at different stages of mesocarp development in high- and low-yielding oil palm.

    Science.gov (United States)

    Wong, Yick Ching; Teh, Huey Fang; Mebus, Katharina; Ooi, Tony Eng Keong; Kwong, Qi Bin; Koo, Ka Loo; Ong, Chuang Kee; Mayes, Sean; Chew, Fook Tim; Appleton, David R; Kulaveerasingam, Harikrishna

    2017-06-21

    The oil yield trait of oil palm is expected to involve multiple genes, environmental influences and interactions. Many of the underlying mechanisms that contribute to oil yield are still poorly understood. In this study, we used a microarray approach to study the gene expression profiles of mesocarp tissue at different developmental stages, comparing genetically related high- and low- oil yielding palms to identify genes that contributed to the higher oil-yielding palm and might contribute to the wider genetic improvement of oil palm breeding populations. A total of 3412 (2001 annotated) gene candidates were found to be significantly differentially expressed between high- and low-yielding palms at at least one of the different stages of mesocarp development evaluated. Gene Ontologies (GO) enrichment analysis identified 28 significantly enriched GO terms, including regulation of transcription, fatty acid biosynthesis and metabolic processes. These differentially expressed genes comprise several transcription factors, such as, bHLH, Dof zinc finger proteins and MADS box proteins. Several genes involved in glycolysis, TCA, and fatty acid biosynthesis pathways were also found up-regulated in high-yielding oil palm, among them; pyruvate dehydrogenase E1 component Subunit Beta (PDH), ATP-citrate lyase, β- ketoacyl-ACP synthases I (KAS I), β- ketoacyl-ACP synthases III (KAS III) and ketoacyl-ACP reductase (KAR). Sucrose metabolism-related genes such as Invertase, Sucrose Synthase 2 and Sucrose Phosphatase 2 were found to be down-regulated in high-yielding oil palms, compared to the lower yield palms. Our findings indicate that a higher carbon flux (channeled through down-regulation of the Sucrose Synthase 2 pathway) was being utilized by up-regulated genes involved in glycolysis, TCA and fatty acid biosynthesis leading to enhanced oil production in the high-yielding oil palm. These findings are an important stepping stone to understand the processes that lead to

  6. Facile and High-Yielding Synthesis of TAM Biradicals and Monofunctional TAM Radicals.

    Science.gov (United States)

    Trukhin, Dmitry V; Rogozhnikova, Olga Yu; Troitskaya, Tatiana I; Vasiliev, Vladimir G; Bowman, Michael K; Tormyshev, Victor M

    2016-04-01

    Facile and high-yielding procedures for synthesis of monocarboxylic acid derivatives of triarylmethyl radicals (TAMs) were developed. Reaction of methyl thioglycolate with tris(2,3,5,6-tetrathiaaryl)methyl cation smoothly afforded the monosubstituted TAM derivative, which was hydrolyzed to a monocarboxylic acid, with the TAM moiety attached to thioglycolic acid via the sulfur atom. Alternatively, the diamagnetic tricarboxylic acid precursor of Finland trityl was transformed to a trimethyl ester and partially hydrolyzed under controlled conditions. The diester product was isolated and the remaining fractions were converted back to the trimethyl ester for production of more diester. The first representatives of TAM biradicals with different TAM cores and interspin distances were obtained by reaction of these new TAM monocaboxylic acids with N,N'-dimethylethylenediamine.

  7. High yield silicon carbide from alkylated or arylated pre-ceramic polymer

    International Nuclear Information System (INIS)

    Baney, R.H.; Gaul, J.H.

    1982-01-01

    Alkylated or arylated methylpolysilanes which exhibit ease of handling and are used to obtain silicon carbide ceramic materials in high yields contain 0 to 60 mole percent (CH 3 ) 2 Si double bond units and 40 to 100 mole percent CH 3 Si triple bond units, wherein there is also bonded to the silicon atoms other silicon atoms and additional alkyl radicals of 1 to 4 carbon atoms or phenyl. They may be prepared by reaction of a Grignard reagent RMgX, where X is halogen and R is Csub(1-4)-alkyl or phenyl, with a starting material which is a solid at 25 0 C, and is identical to the product except that the remaining bonds on the silicon atoms are attached to another silicon atom, or a chlorine or a bromine atom. Ceramics result from heating the polysilane products to 1200 0 C, optionally with fillers. (author)

  8. Garnet Yield Strength at High Pressures and Implications for Upper Mantle and Transition Zone Rheology

    International Nuclear Information System (INIS)

    Kavner, A.

    2008-01-01

    Garnet helps control the mechanical behavior of the Earth's crust, mantle, and transition zone. Here, measurements are presented suggesting that garnet, long considered to be a high-viscosity phase, is actually weaker than the other dominant components in the transition zone. The mechanical behavior of garnet at high pressures was examined using radial diffraction techniques in the diamond anvil cell. The yield strength of grossular garnet was inferred from synchrotron X-ray measurements of differential lattice strains. The differential stress was found to increase from 1.3 (±0.6) GPa at a hydrostatic pressure 5.8 (±1.1) GPa to 4.1 (±0.4) GPa at 15.7 (±1.0) GPa, where it was level to 19 GPa. The strength results are consistent with inferred strength values for majorite garnet from measurements in the diamond cell normal geometry, bolstering the idea that garnet-structured materials may all have similar strengths. In this low-temperature, high differential stress regime, garnet is shown to be significantly weaker than anhydrous ringwoodite and to have a strength similar to hydrous ringwoodite. This result suggests that the presence of water in the transition zone may not be required to explain a weak rheology, and therefore models of transition zone behavior built assuming that garnet is the high-strength phase may need to be revised.

  9. Diagnostic Yield of Transbronchial Biopsy in Comparison to High Resolution Computerized Tomography in Sarcoidosis Cases

    Science.gov (United States)

    Akten, H Serpil; Kilic, Hatice; Celik, Bulent; Erbas, Gonca; Isikdogan, Zeynep; Turktas, Haluk; Kokturk, Nurdan

    2018-04-25

    This study aimed to evaluate the diagnostic yield of fiberoptic bronchoscopic (FOB) transbronchial biopsy and its relation with quantitative findings of high resolution computerized tomography (HRCT). A total of 83 patients, 19 males and 64 females with a mean age of 45.1 years diagnosed with sarcoidosis with complete records of high resolution computerized tomography were retrospectively recruited during the time period from Feb 2005 to Jan 2015. High resolution computerized tomography scans were retrospectively assessed in random order by an experienced observer without knowledge of the bronchoscopic results or lung function tests. According to the radiological staging with HRCT, 2.4% of the patients (n=2) were stage 0, 19.3% (n=16) were stage 1, 72.3% (n=60) were stage 2 and 6.0% (n=5) were stage 3. This study showed that transbronchial lung biopsy showed positive results in 39.7% of the stage I or II sarcoidosis patients who were diagnosed by bronchoscopy. Different high resolution computerized tomography patterns and different scores of involvement did make a difference in the diagnostic accuracy of transbronchial biopsy (p=0.007). Creative Commons Attribution License

  10. Synthesis of uniform CdS nanowires in high yield and its single nanowire electrical property

    International Nuclear Information System (INIS)

    Yan Shancheng; Sun Litao; Qu Peng; Huang Ninping; Song Yinchen; Xiao Zhongdang

    2009-01-01

    Large-scale high quality CdS nanowires with uniform diameter were synthesized by using a rapid and simple solvothermal route. Field emission scan electron microscopy (FESEM) and transmission electron microscopy (TEM) images show that the CdS nanowires have diameter of about 26 nm and length up to several micrometres. High resolution TEM (HRTEM) study indicates the single-crystalline nature of CdS nanowires with an oriented growth along the c-axis direction. The optical properties of the products were characterized by UV-vis absorption spectra, photoluminescence spectra and Raman spectra. The resistivity, electron concentration and electron mobility of single NW are calculated by fitting the symmetric I-V curves measured on single NW by the metal-semiconductor-metal model based on thermionic field emission theory. - Graphical abstract: Large-scale high quality CdS nanowires (NWs) with uniform diameter were synthesized by using a rapid and simple solvothermal route. The reaction time is reduced to 2 h, comparing to other synthesis which needed long reaction time up to 12 h. In addition, the as-prepared CdS nanowires have more uniform diameter and high yield. More importantly, the I-V curve of present single CdS nanowire has a good symmetric characteristic as expected by the theory.

  11. A high-efficiency low-voltage CMOS rectifier for harvesting energy in implantable devices.

    Science.gov (United States)

    Hashemi, S Saeid; Sawan, Mohamad; Savaria, Yvon

    2012-08-01

    We present, in this paper, a new full-wave CMOS rectifier dedicated for wirelessly-powered low-voltage biomedical implants. It uses bootstrapped capacitors to reduce the effective threshold voltage of selected MOS switches. It achieves a significant increase in its overall power efficiency and low voltage-drop. Therefore, the rectifier is good for applications with low-voltage power supplies and large load current. The rectifier topology does not require complex circuit design. The highest voltages available in the circuit are used to drive the gates of selected transistors in order to reduce leakage current and to lower their channel on-resistance, while having high transconductance. The proposed rectifier was fabricated using the standard TSMC 0.18 μm CMOS process. When connected to a sinusoidal source of 3.3 V peak amplitude, it allows improving the overall power efficiency by 11% compared to the best recently published results given by a gate cross-coupled-based structure.

  12. From Digital Commons to OCLC: A Tailored Approach for Harvesting and Transforming ETD Metadata into High-Quality Records

    Directory of Open Access Journals (Sweden)

    Marielle Veve

    2016-07-01

    Full Text Available The library literature contains many examples of automated and semi-automated approaches to harvest electronic theses and dissertations (ETD metadata from institutional repositories (IR to the Online Computer Library Center (OCLC. However, most of these approaches could not be implemented with the institutional repository software Digital Commons because of various reasons including proprietary schema incompatibilities and high level programming expertise requirements our institution did not want to pursue. Only one semi-automated approach was found in the library literature which met our requirements for implementation, and even though it catered to the particular needs of the DSpace IR, it could be implemented to other IR software if further customizations were applied. The following paper presents an extension of this semi-automated approach originally created by Deng and Reese, but customized and adapted to address the particular needs of the Digital Commons community and updated to integrate the latest Resource Description & Access (RDA content standards for ETDs. Advantages and disadvantages of this workflow are discussed and presented as well.

  13. Nerium oleander indirect leaf photosynthesis and light harvesting reductions after clipping injury or Spodoptera eridania herbivory: high sensitivity to injury.

    Science.gov (United States)

    Delaney, Kevin J

    2012-04-01

    Variable indirect photosynthetic rate (P(n)) responses occur on injured leaves after insect herbivory. It is important to understand factors that influence indirect P(n) reductions after injury. The current study examines the relationship between gas exchange and chlorophyll a fluorescence parameters with injury intensity (% single leaf tissue removal) from clipping or Spodoptera eridania Stoll (Noctuidae) herbivory on Nerium oleander L. (Apocynaceae). Two experiments showed intercellular [CO(2)] increases but P(n) and stomatal conductance reductions with increasing injury intensity, suggesting non-stomatal P(n) limitation. Also, P(n) recovery was incomplete at 3d post-injury. This is the first report of a negative exponential P(n) impairment function with leaf injury intensity to suggest high N. oleander leaf sensitivity to indirect P(n) impairment. Negative linear functions occurred between most other gas exchange and chlorophyll a fluorescence parameters with injury intensity. The degree of light harvesting impairment increased with injury intensity via lower (1) photochemical efficiency indicated lower energy transfer efficiency from reaction centers to PSII, (2) photochemical quenching indicated reaction center closure, and (3) electron transport rates indicated less energy traveling through PSII. Future studies can examine additional mechanisms (mesophyll conductance, carbon fixation, and cardenolide induction) to cause N. oleander indirect leaf P(n) reductions after injury. Published by Elsevier Ireland Ltd.

  14. Pathomorphological characteristics of abomasal ulcers in high-yielding dairy cows

    Directory of Open Access Journals (Sweden)

    Kureljušić Branislav

    2013-01-01

    Full Text Available The aim of this paper was to investigate the morphology, localization and typization of abomasal ulcers in high-yielding dairy cows, as a contribution to the existing knowledge on the subject. A total of ten high-yielding dairy cows which died during the period of early puerperium and two Holstein heifers which died in late pregnancy after transport to a new location were investigated in this study. Samples of altered abomasal tissue were taken at necropsy for further histopathology and mycology investigations. The disclosed ulcerations of the abomasums in twelve investigated animals differed among them not only as far as localization and morphology are concerned, but also in the degree of intramural penetration. Such differences distinguished them into four types. Ulcerations of type one and type two, recorded in two heifers and six cows, as well as in one cow with lymphoma of the abomasum. Perforating ulcer of type three, with circumscripted peritonitis was diagnosed in one cow in the corpus of the abomasum close to the curvatura major. An interesting finding was the simultaneous occurrence of type four perforating ulcer and ulcer-type one, which were located next to each other. Histopathological examination of the structure of the ulcerated abomasum dyed with the hematoxylin-eosin method showed that coagulation necrosis in the area of the ulceration revealed a moderate inflammatory infiltrate in the lamina propria. In the cow affected with lymphoma, a copious tumorous lymphoid infiltrate was concurrent. Mycotic ulcerative abomasitis was described in a cow seven days after calving. In these lesions Aspergillus fumigatus and Mucor spp. were isolated. Histopathological analysis of tissue samples dyed with the Grocott method, described septed and nonsepted hyphae in the blood vessels and surrounding tissue of the tunica mucosa and submucosa.

  15. Inheritance of seed yield and related traits in some lentil (lens culinaris medik) genotypes

    International Nuclear Information System (INIS)

    Rasheed, S.; Hanif, M.; Sadiq, S.; Abbas, G.; Asghar, M.J.; Haq, M.A.

    2008-01-01

    The study was conducted at Nuclear Institute for Agriculture and Biology (NIAB), Faisalabad during the year 2006-2007. Fifteen lentil lines/varieties were evaluated to exploit yield components to the maximum extent and to formulate section criteria for the improvement of seed yield. Significant genetic variation was observed for all the traits. All the traits under study had high heritability values except number of primary branches. Higher values of heritability coupled with genetic advance were observed for seed yield (98.30%, 128.20%), harvest index (97.10%, 79.40%), biological yield (94.30%, 56.10%) and hundred seed weight (88.30%, 50.80%) which indicates The role of additive genes to control these traits. Hundred seed weight (0.67, 0.65), harvest index (0.94, 0.93) and Biological yield (0.81, 0.80) had positive and highly significant correlation with seed yield at both genotypic and phenotypic levels. Number of primary branches, hundred seed weight, harvest index and biological yield showed positive direct effect along with positive genotypic correlation with seed yield. Finally, it was concluded that the traits like hundred seed weight, harvest index and biological yield can be exploited for the improvement of seed yield in lentil. (author)

  16. Microalgae harvesting techniques: A review.

    Science.gov (United States)

    Singh, Gulab; Patidar, S K

    2018-07-01

    Microalgae with wide range of commercial applications have attracted a lot of attention of the researchers in the last few decades. However, microalgae utilization is not economically sustainable due to high cost of harvesting. A wide range of solid - liquid separation techniques are available for microalgae harvesting. The techniques include coagulation and flocculation, flotation, centrifugation and filtration or a combination of various techniques. Despite the importance of harvesting to the economics and energy balance, there is no universal harvesting technique for microalgae. Therefore, this review focuses on assessing technical, economical and application potential of various harvesting techniques so as to allow selection of an appropriate technology for cost effectively harvesting of microalgae from their culture medium. Various harvesting and concentrating techniques of microalgae were reviewed to suggest order of suitability of the techniques for four main microalgae applications i.e biofuel, human and animal food, high valued products, and water quality restoration. For deciding the order of suitability, a comparative analysis of various harvesting techniques based on the six common criterions (i.e biomass quality, cost, biomass quantity, processing time, species specific and toxicity) has been done. Based on the order of various techniques vis-a-vis various criteria and preferred order of criteria for various applications, order of suitability of harvesting techniques for various applications has been decided. Among various harvesting techniques, coagulation and flocculation, centrifugation and filtration were found to be most suitable for considered applications. These techniques may be used alone or in combination for increasing the harvesting efficiency. Copyright © 2018 Elsevier Ltd. All rights reserved.

  17. West Virginia harvest and utilization study, 2008

    Science.gov (United States)

    Jan Wiedenbeck; Shawn. Grushecky

    2014-01-01

    Thirty active harvesting operations were part of a harvest and utilization study conducted in West Virginia in 2008. Data were collected on roundwood product and residue yields obtained from trees of different sizes, species, and qualities. This study was modeled after studies conducted on a regular and frequent basis by the Forest Inventory and Analysis unit in the...

  18. High-yield Synthesis of Multiwalled Carbon Nanotube by Mechanothermal Method

    Directory of Open Access Journals (Sweden)

    Manafi SA

    2009-01-01

    Full Text Available Abstract This study reports on the mechanothermal synthesis of multiwalled carbon nanotube (MWCNTs from elemental graphite powder. Initially, high ultra-active graphite powder can be obtained by mechanical milling under argon atmosphere. Finally, the mechanical activation product is heat-treated at 1350°C for 2–4 h under argon gas flow. After heat-treatment, active graphite powders were successfully changed into MWCNTs with high purity. The XRD analyses showed that in the duration 150 h of milling, all the raw materials were changed to the desired materials. From the broadening of the diffraction lines in the XRD patterns, it was concluded that the graphite crystallites were nanosized, and raising the milling duration resulted in the fineness of the particles and the increase of the strain. The structure and morphology of MWCNTs were investigated using scanning electron microscopy (SEM and high-resolution transmission electron microscopy (HRTEM. The yield of MWCNTs was estimated through SEM and TEM observations of the as-prepared samples was to be about 90%. Indeed, mechanothermal method is of interest for fundamental understanding and improvement of commercial synthesis of carbon nanotubes (CNTs. As a matter of fact, the method of mechanothermal guarantees the production of MWCNTs suitable for different applications.

  19. Improved yield of high resolution mercuric iodide gamma-ray spectrometers

    International Nuclear Information System (INIS)

    Gerrish, V.; van den Berg, L.

    1990-01-01

    Mercuric iodide (HgI 2 ) exhibits properties which make it attractive for use as a solid state nuclear radiation detector. The wide bandgap (E g = 2.1 eV) and low dark current allow room temperature operation, while the high atomic number provides a large gamma-ray cross section. However, poor hole transport has been a major limitation in the routine fabrication of high-resolution spectrometers using this material. This paper presents the results of gamma-ray response and charge transport parameter measurements conducted during the past year at EG ampersand G/EM on 96 HgI 2 spectrometers. The gamma-ray response measurements reveal that detector quality is correlated with the starting material used in the crystal growth. In particular, an increased yield of high-resolution spectrometers was obtained from HgI 2 which was synthesized by precipitation from an aqueous solution, as opposed to using material from commercial vendors. Data are also presented which suggest that better spectrometer performance is tied to improved hole transport. Finally, some initial results on a study of detector uniformity reveal spatial variations which may explain why the correlation between hole transport parameters and spectrometer performance is sometimes violated. 6 refs., 3 figs

  20. Teor e composição do óleo essencial de inflorescências e folhas de Lavandula dentata L. em diferentes estádios de desenvolvimento floral e épocas de colheita Yield and composition of essential oil from inflorescences and leaves of lavender (Lavandula dentata L. in different flower development stages and harvest times

    Directory of Open Access Journals (Sweden)

    M.A.M. Masetto

    2011-01-01

    , cosmetic and personal care industries. The aim of this study was to evaluate the yield and composition of essential oil from lavender inflorescences and leaves in different development stages. The experimental design was completely randomized in 2 x 3 factorial arrangement, with three flower development stages (bud, pre-anthesis/anthesis and senescence and two harvest periods (January and April, and 5 replicates. The essential oil samples were obtained by hydrodistillation, and the compounds were analyzed by gas chromatography coupled to mass spectrometry (GC/MS. There was an interaction between the factors harvest time and flower development on essential oil yield of inflorescences, and a superior average was observed for flower buds harvested in January. The development stages did not alter the essential oil yield of leaves. The development stages influenced the levels of compounds of the essential oil from inflorescences and leaves. For essential oil in senescent flower stage harvested in April, there was a high level of 1,8-cineol, whereas in the remaining development stages, the levels were lower in both harvest times. The levels of camphor increased in the pre-anthesis/anthesis and senescence in January harvest. The essential oil from leaves presented higher levels of 1,8-cineol in branches with flowers in pre-anthesis/anthesis. Camphor and fenchone levels were higher in branches with buds. The essential oil from leaves of branches with buds and senescent flowers showed higher levels of linalool than that from inflorescences.

  1. Does high yield spread dampen economic growth? : the case of US-Japan

    Directory of Open Access Journals (Sweden)

    Yutaka Kurihara

    2014-04-01

    Full Text Available This article focuses on the relationship between the United States' and Japan's yield spread of interest rates and economic growth in Japan. The yield spread is defined in this article as the difference between the Japanese government bond yield minus the US government bond yield. Some studies have tackled this issue and found a negative relationship between the yield spread and economic growth; however, recent studies have shown no or a weak relationship. This problem has not yet consensus in spite of its importance. As the Japanese interest rate has been quite low since the adoption of the zero interest rate policy at the end of 1990s, the situation may change the results. The empirical results show that reliability of yield spread as a leading indicator of output growth exists in Japan; however, term structure of interest rate is not related to economic growth.

  2. [Construction of high-yield strain by optimizing lycopene cyclase for β-carotene production].

    Science.gov (United States)

    Jin, Yingfu; Han, Li; Zhang, Shasha; Li, Shizhong; Liu, Weifeng; Tao, Yong

    2017-11-25

    To optimize key enzymes, such as to explore the gene resources and to modify the expression level, can maximize metabolic pathways of target products. β-carotene is a terpenoid compound with important application value. Lycopene cyclase (CrtY) is the key enzyme in β-carotene biosynthesis pathway, catalyzing flavin adenine dinucleotide (FAD)-dependent cyclization reaction and β-carotene synthesis from lycopene precursor. We optimized lycopene cyclase (CrtY) to improve the synthesis of β-carotene and determined the effect of CrtY expression on metabolic pathways. Frist, we developed a β-carotene synthesis module by coexpressing the lycopene β-cyclase gene crtY with crtEBI module in Escherichia coli. Then we simultaneously optimized the ribosome-binding site (RBS) intensity and the species of crtY using oligo-linker mediated DNA assembly method (OLMA). Five strains with high β-carotene production capacity were screened out from the OLMA library. The β-carotene yields of these strains were up to 15.79-18.90 mg/g DCW (Dry cell weight), 65% higher than that of the original strain at shake flask level. The optimal strain CP12 was further identified and evaluated for β-carotene production at 5 L fermentation level. After process optimization, the final β-carotene yield could reach to 1.9 g/L. The results of RBS strength and metabolic intermediate analysis indicated that an appropriate expression level of CrtY could be beneficial for the function of the β-carotene synthesis module. The results of this study provide important insight into the optimization of β-carotene synthesis pathway in metabolic engineering.

  3. Aplicação de dessecantes na cultura de soja: antecipação da colheita e produção de sementes Application of desiccants on soybean crop glycine max: harvest anticipation and seed yield

    Directory of Open Access Journals (Sweden)

    A.L.S. Lacerda

    2001-12-01

    Full Text Available Este trabalho foi conduzido no município de Selvíria-MS, semeando soja do cultivar IAC-15. O delineamento experimental utilizado foi o de blocos casualizados, estando os tratamentos dispostos em um esquema fatorial 3x3 e 4x4, sendo os fatores os produtos (dessecantes e as épocas de aplicação, nos anos agrícolas 1996/97 e 1997/98, respectivamente. Os dessecantes utilizados foram: paraquat, diquat e mistura paraquat + diquat, nas dosagens de 0,4; 0,3 e 0,2+0,15 em 1996/97, respectivamente, e os mesmos tratamentos em 1997/98, além do glufosinato de amônio na dosagem de 0,4 kg i.a. ha-1 em 1997/98. Como épocas, foram realizadas três aplicações em 1996/97 e quatro em 1997/98, todas espaçadas de cinco dias a partir do estádio fenológico médio da cultura R6. Concluiu-se que os dessecantes utilizados mostraram-se eficientes na dessecação da soja; foi possível obter antecipação da colheita de sementes de soja, sem alterar a produção, por um período máximo de sete dias.This research was carried out in Selvíria-MS, Brazil, during the growing seasons of 1996/97 and 1997/98, using the soybean cultivar IAC-15. The experimental design was arranged in randomized complete blocks in a 3x3 and 4x4 factorial scheme during 1996/97 and 1997/98, respectively, with the factors being the products (desiccants and timing of application. The desiccants sprayed were: paraquat, diquat and a mixture of paraquat + diquat at rates of 0.4; 0.3 and 0.2+0.15 in 1996/97 and the same treatments in 1997/98 added to ammonium glufosinate at 0.4 kg a.i. ha-1 in 1997/98. The timing of application was spaced every five days, starting from the soybean vegetative stage R6. The tested desiccants were efficient on the soybean desiccation ; it was possible to obtain grain harvest anticipation, without yield reduction, in a maximum period of seven days.

  4. Development of high yielding mutants of Brassica campestris L. cv. Toria selection through gamma rays irradiation

    International Nuclear Information System (INIS)

    Javed, M.A.; Siddiqui, M.A.; Khan, M.K.R.; Khatri, A.; Khan, I.A.; Dahar, N.A.; Khanzada, M.H.; Khan, R.

    2003-01-01

    Homogeneous seeds of Brassica campestris L. cv. Toria selection were treated with different doses of gamma rays (750, 1000 and 1250 Gy) to induce genetic variability for the selection of new genotypes with improved agronomic traits. After passing through different stages of selection, two promising mutants were selected for further studies. Two selected mutants along with 5 other entries including parent variety were evaluated for yield and yield components in yield trials for two consecutive years. The mutant TS96-752 was significantly (P less than or equal to 0.05) superior to all other entries in grain yield but at par with FSD 86028-3

  5. Energy harvesting for microsystems

    Energy Technology Data Exchange (ETDEWEB)

    Ruichao Xu

    2012-05-15

    The purpose of this project is to design and fabricate piezoelectric energy harvesters based on integration of Pb(ZrxTi1-x)O3 (PZT) thick film technology and silicon microtechnology. The fabrication processes are carried out in close collaboration with Meggitt Sensing Systems (MSS) who has the unique expertise to screen print piezoelectric thick film layers, thus all screen printing steps are done by MSS while the silicon micromachining is carried out at Danchip facility at DTU. The presented energy harvesters are all based on using piezoelectric thick film operating in the 31-mode to generate power when strained. Three archetypes of the numerous fabricated energy harvesters will be presented in detail, they represent three major milestones in this project. The first energy harvester archetype has an unimorph cantilever beam, which consists of a 20 {mu}m silicon layer and 10-30 {mu}m screen printed PZT layer, anchored on a silicon frame at one end and attached to a silicon proof mass at the other. Electrodes will cover both side of the PZT layer, so the harvested energy can be collected electrically. The second archetype has a bimorph cantilever beam, which consists of two 15-35 {mu}m PZT layers, anchored on a silicon frame at the one end and attached to a silicon proof mass at the other. Electrodes are deposited below, between and above the two PZT layers. The root mean square (RMS) power output measured on this type of harvesters is as high as 37.1{mu}W at 1 g. The third archetype is similar to the first one, the screen printed PZT layer is replaced by a lead free piezoelectric material, (KxNa1-x)NbO3 (KNN). Some of the major challenges encountered during the development processes are bad adhesion, fragile structures and short circuiting through the PZT layer. All of which have being fully or partially solved in this project. The final energy harvesters are designed to be used in an energy harvester powered wireless sensing system. (Author)

  6. Experimental verificatio of load resistance switching for global stabilization of high-energy response of a nonlinear wideband electromagnetic vibration energy harvester

    International Nuclear Information System (INIS)

    Sato, T; Masuda, A; Sanada, T

    2015-01-01

    This paper presents an experimental verification of a self-excitation control of a resonance- type vibration energy harvester with a Duffing-type nonlinearity which is designed to perform effectively in a wide frequency range. For the conventional linear vibration energy harvester, the performance of the power generation at the resonance frequency and the bandwidth of the resonance peak are trade-off. The resonance frequency band can be expanded by introducing a Duffing-type nonlinear oscillator in order to enable the harvester to generate larger electric power in a wider frequency range. However, since such nonlinear oscillator can have multiple stable steady-state solutions in the resonance band, it is difficult for the nonlinear harvester to maintain the high performance of the power generation constantly. The principle of self-excitation and entrainment has been utilized to provide the global stability to the highest-energy solution by destabilizing other unexpected lower-energy solutions by introducing a switching circuit of the load resistance between positive and the negative values depending on the response amplitude of the oscillator. It has been experimentally validated that this control law imparts the self-excitation capability to the oscillator to show an entrainment into the highest-energy solution. (paper)

  7. Engineering, nutrient removal, and feedstock conversion evaluations of four corn stover harvest scenarios

    Energy Technology Data Exchange (ETDEWEB)

    Hoskinson, Reed L.; Radtke, Corey W. [Idaho National Laboratory, P.O Box 1625, Idaho Falls, ID 83415-2210 (United States); Karlen, Douglas L. [USDA-ARS, National Soil Tilth Laboratory, Ames, IA 50011-3120 (United States); Birrell, Stuart J. [Iowa State University, Agricultural and Biosystems Engineering Department, Ames, IA 50011 (United States); Wilhelm, W.W. [USDA-ARS, Soil and Water Conservation Research Unit, Lincoln, NE 68583-0934 (United States)

    2007-02-15

    Crop residue has been identified as a near-term source of biomass for renewable fuel, heat, power, chemicals and other bio-materials. A prototype one-pass harvest system was used to collect residue samples from a corn (Zea mays L.) field near Ames, IA. Four harvest scenarios (low cut, high-cut top, high-cut bottom, and normal cut) were evaluated and are expressed as collected stover harvest indices (CSHI). High-cut top and high-cut bottom samples were obtained from the same plot in separate operations. Chemical composition, dilute acid pretreatment response, ethanol conversion yield and efficiency, and thermochemical conversion for each scenario were determined. Mean grain yield in this study (10.1 Mg ha{sup -1} dry weight) was representative of the average yield (10.0 Mg ha{sup -1}) for the area (Story County, IA) and year (2005). The four harvest scenarios removed 6.7, 4.9, 1.7, and 5.1 Mg ha{sup -1} of dry matter, respectively, or 0.60 for low cut, 0.66 for normal cut, and 0.61 for the total high-cut (top+bottom) scenarios when expressed as CSHI values. The macro-nutrient replacement value for the normal harvest scenario was $57.36 ha{sup -1} or $11.27 Mg{sup -1}. Harvesting stalk bottoms increased stover water content, risk of combine damage, estimated transportation costs, and left insufficient soil cover, while also producing a problematic feedstock. These preliminary results indicate harvesting stover (including the cobs) at a height of approximately 40 cm would be best for farmers and ethanol producers because of faster harvest speed and higher quality ethanol feedstock. (author)

  8. THE INFLUENCE OF FERTILIZATION ON YIELD AND YIELD COMPONENT FORMATION OF SOYBEAN VARIETIES

    Directory of Open Access Journals (Sweden)

    Eva CANDRÁKOVÁ

    2009-03-01

    Full Text Available In 2005 and 2006, the influence of fertilization was investigated on forming of yield components and yield of three soybean varieties in sugar beet growing area. Varieties Korada, Supra and OAC Vision were grown. Number of plants per m2, number of pods per plant, number of seeds in pod, thousand seeds weight, yield of seeds, yield of stems and harvest index were examined. Variants of fertilization: I. non-fertilized control, II. LAV 27 % (40 kg ha-1 net nutrient of N in growing stage of first pair of true leaves unfolded, III. Humix komplet (rate 8 l.ha-1 applied in growing stage of first pair of true leaves unfolded (4 l.ha-1 and in growing stage of first flower buds visible (4 l.ha-1, IV. Humix komplet in rate 8 l.ha-1 applied in growing stage of first pair of true leaves unfolded. The yields of seeds and stems were high significantly influenced by variety, fertilization and year. The significantly highest yield of seeds was achieved by Korada variety (4,04 t.ha-1. Varieties OAC Vision and Supra reached yields in interval 3,74-3,84 t.ha-1. Split rate of Humix komplet (III var significantly influenced yield of seeds and stems. The fertilization have increased weight of seeds in proportion to aboveground phyto-mass weight, what was expressed by harvest index.

  9. Screening of high-yield GTF yeast by N+-implantation

    International Nuclear Information System (INIS)

    Gao Yanhong; Lv Jiaping; Liu Lu; Li Shurong

    2009-01-01

    In this study, one of the highest chromium-resistant strain was screened from 12 tested brewer's yeast. N + ion implantation was used to mutate this yeast and screened high-yield GTF yeast strains with Chromium tolerance method. The mutagenesis was conducted by 50 KeV N + ion implantation with the doses of 1 x 2.6 x 10 13 , 2 x 2.6 x 10 13 , 3 x 2.6 x 10 13 , 4 x 2.6 x 10 13 , 5 x 2.6 x 10 13 and 6 x 2.6 x 10 13 ion/cm 2 . Results showed that the optimum dose was 4 x 2.6 x 10 13 ion/cm 2 , and a strain M11-1A11 of high-producing GTF was obtained. Its organic Cr content was increased by 22.4% than the original strain. Its fermentation property was stable after 5 generation transfer inoculation. (authors)

  10. Theoretical investigations on the high light yield of the LuI3:Ce scintillator

    International Nuclear Information System (INIS)

    Vasil'ev, A.N.; Iskandarova, I.M.; Scherbinin, A.V.; Markov, I.A.; Bagatur'yants, A.A.; Potapkin, B.V.; Srivastava, A.M.; Vartuli, J.S.; Duclos, S.J.

    2009-01-01

    The extremely high scintillation efficiency of lutetium iodide doped by cerium is explained as a result of at least three factors controlling the energy transfer from the host matrix to activator. We propose and theoretically validate the possibility of a new channel of energy transfer to excitons and directly to cerium, namely the Auger process when Lu 4f hole relaxes to the valence band hole with simultaneous creation of additional exciton or excitation of cerium. This process should be efficient in LuI 3 , and inefficient in LuCl 3 . To justify this channel, we perform calculations of density of states using a periodic plane-wave density functional approach. The second factor is the increase of the efficiency of valence hole capture by cerium in the row LuCl 3 -LuBr 3 -LuI 3 . The third one is the increase of the efficiency of energy transfer from self-trapped excitons to cerium ions in the same row. The latter two factors are verified by cluster ab initio calculations. We estimate either the relaxation of these excitations and barriers for the diffusion of self-trapped holes (STH) and self-trapped exciton (STE). The performed estimations theoretically justify the high LuI 3 :Ce 3+ scintillator yield.

  11. Crop Yield Predictions - High Resolution Statistical Model for Intra-season Forecasts Applied to Corn in the US

    Science.gov (United States)

    Cai, Y.

    2017-12-01

    Accurately forecasting crop yields has broad implications for economic trading, food production monitoring, and global food security. However, the variation of environmental variables presents challenges to model yields accurately, especially when the lack of highly accurate measurements creates difficulties in creating models that can succeed across space and time. In 2016, we developed a sequence of machine-learning based models forecasting end-of-season corn yields for the US at both the county and national levels. We combined machine learning algorithms in a hierarchical way, and used an understanding of physiological processes in temporal feature selection, to achieve high precision in our intra-season forecasts, including in very anomalous seasons. During the live run, we predicted the national corn yield within 1.40% of the final USDA number as early as August. In the backtesting of the 2000-2015 period, our model predicts national yield within 2.69% of the actual yield on average already by mid-August. At the county level, our model predicts 77% of the variation in final yield using data through the beginning of August and improves to 80% by the beginning of October, with the percentage of counties predicted within 10% of the average yield increasing from 68% to 73%. Further, the lowest errors are in the most significant producing regions, resulting in very high precision national-level forecasts. In addition, we identify the changes of important variables throughout the season, specifically early-season land surface temperature, and mid-season land surface temperature and vegetation index. For the 2017 season, we feed 2016 data to the training set, together with additional geospatial data sources, aiming to make the current model even more precise. We will show how our 2017 US corn yield forecasts converges in time, which factors affect the yield the most, as well as present our plans for 2018 model adjustments.

  12. Fast co-pyrolysis of waste newspaper with high-density polyethylene for high yields of alcohols and hydrocarbons.

    Science.gov (United States)

    Chen, Weimin; Shi, Shukai; Chen, Minzhi; Zhou, Xiaoyan

    2017-09-01

    Waste newspaper (WP) was first co-pyrolyzed with high-density polyethylene (HDPE) using pyrolysis-gas chromatography/mass spectrometry (Py-GC/MS) to enhance the yields of alcohols and hydrocarbons. The effects of WP: HDPE feed ratio (100:0, 75:25, 50:50, 25:75, 0:100) and temperature (500-800°C) on products distribution were investigated and the interaction mechanism during co-pyrolysis was also proposed. Maximum yields of alcohols and hydrocarbons reached 85.88% (feed ratio 50:50wt.%, 600°C). Hydrogen supplements and deoxidation by HDPE and subsequently fragments recombination result in the conversion of aldehydes and ketones into branched hydrocarbons. Radicals from WP degradation favor the secondary crack for HDPE products resulting in the formation of linear hydrocarbons with low carbon number. Hydrocarbons with activated radical site from HDPE degradation were interacted with hydroxyl from WP degradation promoting the formation of linear long chain alcohols. Moreover, co-pyrolysis significantly enhanced condensable oil qualities, which were close to commercial diesel No. 0. Copyright © 2017 Elsevier Ltd. All rights reserved.

  13. Semi-dwarf tef lines for high seed yield and lodging tolerance in ...

    African Journals Online (AJOL)

    The grain of tef is not only nutritious but also gluten-free, the cause for celiac disease, which affects humans world wide. The objective of this study was to evaluate the morpho-agronomic performance of newly developed semi-dwarf tef genotypes for grain yield and yield related agronomic traits under diverse environmental ...

  14. Induction of embryogenic callus and plantlet regeneration from young leaves of high yielding mature oil palm

    Directory of Open Access Journals (Sweden)

    Yeedum, I.

    2004-09-01

    Full Text Available Callus induction and plantlet regeneration from young leaves of high-yielding mature oil palm were carried out using 10-year and 20-year-old trees from Thepa Research Station, Faculty of Natural Resources,Prince of Songkla University, Hat Yai, and Trang Agricultural College, respectively. Culture media used in this experiment were Murashige and Skoog (1962 and Oil Palm supplemented with various concentrations of α-naphthaleneacetic acid (NAA or 2,4- dichlorophenoxy acetic acid (2,4-D or dicamba (Di and antioxidants.Young leaves from 6th to 11st frond were excised, sterilized, cut into 5x5 mm pieces and cultured in the dark at 26±4ºC or 28±0.5ºC for 3 months. The results revealed that MS medium with 200 mg/l ascorbic acid (As and 1 mg/l Di (MS-AsDi gave the highest callus induction percentage (7.93 after culture for 3 months at 28±0.5ºC. Leaf segments from 6th - 8th frond yielded callus forming percentage at 10% (averaged from 1, 2.5 and 5 mg/l Di containing MS medium. Ascorbic acid as an antioxidant at concentration of 200 mg/l supplemented in MS medium in the presence of 2.5 mg/l Di produced the highest callus induction percentage (11.2 and number of nodules (7.06. A high percentage of embryogenic callus formation (66.67 was obtained when the calli were transferred to the same medium component supplemented with 0.5 mg/l Di and 1,000 mg/l casein hydrolysate (CH (MS-AsDiCH. Haustorial-staged embryos were observed to be isolated as an individual embryo and germinated on MS medium without plant growth regulator (MS-free. Development of root could be classified into two distinct types, fibrous and tap root.

  15. Milk yield and composition, nutrition, body conformation traits, body condition scores, fertility and diseases in high-yielding dairy cows--Part 1.

    Science.gov (United States)

    Aeberhard, K; Bruckmaier, R M; Kuepfer, U; Blum, J W

    2001-03-01

    Twenty-nine pairs of high-yielding dairy cows (HC; > or = 45 kg/day reached at least once during lactation) and corresponding control cows (CC; with milk yields representing the average yield of the herds) were examined on 29 Swiss farms from March 1995 to September 1996. The hypotheses were tested that there are differences in feed intake, body-conformation traits, body weight (BW), body condition score (BCS), fertility status and disease incidence between HC and CC cows. Cows were studied 2 weeks before and at 5, 9, 13, 17 and 40 weeks post-partum. HC cows produced more energy-corrected milk (ECM) than CC cows (10,670 +/- 321 kg in 293 +/- 5 days and 8385 +/- 283 kg in 294 +/- 4 days, respectively; P cows (46.2 +/- 1.1 and 36.2 +/- 1.0 kg ECM/day, respectively; P cows (7.6 +/- 0.5 and 5.7 +/- 0.5 kg/day, respectively) and dry matter intakes (measured in week 5 of lactation over 3 days on six farms) were greater in HC than in CC cows (24.0 +/- 1.1 and 20.3 +/- 1.1 kg/day, respectively; P cows were taller than CC cows (wither heights 143.3 +/- 0.8 and 140.1 +/- 0.8 cm, respectively; P cows was greater than in CC cows throughout the study, differences and decreases of BW during lactation were not significant. BCS at the end of pregnancy and decrements during lactation were similar in HC and CC cows. Fertility parameters were similar in HC and CC cows. Incidences of mastitis, claw and feet problems, hypocalcemia/downer cow syndrome, ovarian cysts and abortions were similar in HC and CC cows, but there were more indigestion problems in HC than in CC cows.

  16. Highly efficient energy transfer from a carbonyl carotenoid to chlorophyll a in the main light harvesting complex of Chromera velia.

    Science.gov (United States)

    Durchan, Milan; Keşan, Gürkan; Slouf, Václav; Fuciman, Marcel; Staleva, Hristina; Tichý, Josef; Litvín, Radek; Bína, David; Vácha, František; Polívka, Tomáš

    2014-10-01

    We report on energy transfer pathways in the main light-harvesting complex of photosynthetic relative of apicomplexan parasites, Chromera velia. This complex, denoted CLH, belongs to the family of FCP proteins and contains chlorophyll (Chl) a, violaxanthin, and the so far unidentified carbonyl carotenoid related to isofucoxanthin. The overall carotenoid-to-Chl-a energy transfer exhibits efficiency over 90% which is the largest among the FCP-like proteins studied so far. Three spectroscopically different isofucoxanthin-like molecules were identified in CLH, each having slightly different energy transfer efficiency that increases from isofucoxanthin-like molecules absorbing in the blue part of the spectrum to those absorbing in the reddest part of spectrum. Part of the energy transfer from carotenoids proceeds via the ultrafast S2 channel of both the violaxanthin and isofucoxanthin-like carotenoid, but major energy transfer pathway proceeds via the S1/ICT state of the isofucoxanthin-like carotenoid. Two S1/ICT-mediated channels characterized by time constants of ~0.5 and ~4ps were found. For the isofucoxanthin-like carotenoid excited at 480nm the slower channel dominates, while those excited at 540nm employs predominantly the fast 0.5ps channel. Comparing these data with the excited-state properties of the isofucoxanthin-like carotenoid in solution we conclude that, contrary to other members of the FCP family employing carbonyl carotenoids, CLH complex suppresses the charge transfer character of the S1/ICT state of the isofucoxanthin-like carotenoid to achieve the high carotenoid-to-Chl-a energy transfer efficiency. Copyright © 2014 Elsevier B.V. All rights reserved.

  17. High-yield well modes and production practices in the Longwangmiao Fm gas reservoirs, Anyue Gas Field, central Sichuan Basin

    Directory of Open Access Journals (Sweden)

    Zhongren Yu

    2016-12-01

    Full Text Available The lithologic Longwangmiao Fm gas reservoirs are situated in the Moxi Block of the Anyue Gas Field, central Sichuan Basin. Due to their great heterogeneity affected by the differential roles of lithologic facies and karstification, huge differences exist in the single-well gas yield tests. To improve the development efficiency of gas reservoirs and achieve the goal of “high yield but with few wells to be drilled”, it is especially important to establish a high-yield gas well mode by use of cores, logging, seismic data, etc., and through analysis of reservoir properties, high-yield controlling factors, and seismic response features of quality reservoirs and so on. The following findings were achieved. (1 The positive relationship between yield and the thickness of dissolved vug reservoirs is obvious. (2 The dissolved vug reservoirs are reflected as the type of honeycomb dark patches from the image logging and the conventional logging is featured generally by “Three Lows and Two Highs (i.e., low GR, low RT and low DEN but high AC and high CNL”. (3 From the seismic profile, the highlighted spots (strong peaks correspond to the bottom boundary of the Longwangmiao Fm reservoirs. The trough waves in larger amplitude represents that there are more well-developed karsts in the reservoirs. On this basis, high-quality 3D seismic data was used for tracking and fine interpretation of those highlighted spots and trough waves on the strong peaks to describe the plane distribution of high-yield dissolved vug reservoirs in this study area. This study is of great significance to the good planning of development wells and well trajectory planning and adjustment. As a result, high-thickness dissolved vug reservoirs have been targeted in this study area with the tested gas yield of 28 wells reaching up to 100 × 104 m3/d among the completed and tested 30 wells in total.

  18. Centralised urban stormwater harvesting for potable reuse.

    Science.gov (United States)

    McArdle, P; Gleeson, J; Hammond, T; Heslop, E; Holden, R; Kuczera, G

    2011-01-01

    Urban impervious areas provide a guaranteed source of runoff, especially in cities with high rainfall - this represents a source of water with low sensitivity to unfavourable climate change. Whilst the potential to reuse stormwater has long been recognised, its quality has largely limited usage to non-potable applications requiring the use of a third-pipe network, a prohibitively expensive option in established urban areas. Given recent advances in membrane filtration, this study investigates the potential of harvesting and treating stormwater to a potable standard to enable use of the potable distribution network. A case study based on the Throsby Creek catchment in Newcastle explores the issue. The high seasonally uniform rainfall provides insight into the maximum potential of such an option. Multicriterion optimisation was used to identify Pareto optimal solutions for harvesting, storing and treating stormwater. It is shown that harvesting and treating stormwater from a 13 km² catchment can produce yields ranging from 8.5 to 14.2 ML/day at costs ranging from AU$2.60/kL to AU$2.89/kL, which may become viable as the cost of traditional supply continues to grow. However, there are significant social impacts to deal with including alienation of public land for storage and community acceptance of treated stormwater.

  19. Genetic variability, trait association and path analysis of yield and yield components in mungbean (vigna radiata (L.) wilczek)

    International Nuclear Information System (INIS)

    Tabasum, A.; Saleem, M.; Aziz, I.

    2010-01-01

    Genetic variability, heritability along with genetic advance of traits, their association and direct and indirect effects on yield are essential for crop improvement. Ten mungbean genotypes were studied to assess variability and degree to which various plant traits associate with seed yield. Primary and secondary branches, pods per cluster and pod length showed lesser variability while clusters per plant, 100 seed weight and harvest index exhibited intermediate range of variability. Sufficient genetic variability was observed for plant height, pods per plant, total plant weight and seed yield. Moderate to high heritability estimates were found for all traits. Primary and secondary branches per plant, pod length and 100-seed weight exhibited negative and non significant genotypic and phenotypic correlations with seed yield. Plant height showed positive non-significant and significant genotypic and phenotypic correlation. Pods per cluster correlated significantly negative with seed yield. Clusters per plant, pods per plant, total plant weight and harvest index showed positive significant genotypic and phenotypic correlations with seed yield. Positive direct effects were exerted through secondary branches, pods per plant, pod length, 100 seed weight, total plant weight and harvest index while primary branches, plant height, clusters per plant and pods per cluster had negative direct effects. The present findings could be useful for establishing selection criteria for high seed yield in the mungbean breeding. (author)

  20. High Quantum Yield Blue Emission from Lead-Free Inorganic Antimony Halide Perovskite Colloidal Quantum Dots.

    Science.gov (United States)

    Zhang, Jian; Yang, Ying; Deng, Hui; Farooq, Umar; Yang, Xiaokun; Khan, Jahangeer; Tang, Jiang; Song, Haisheng

    2017-09-26

    Colloidal quantum dots (QDs) of lead halide perovskite have recently received great attention owing to their remarkable performances in optoelectronic applications. However, their wide applications are hindered from toxic lead element, which is not environment- and consumer-friendly. Herein, we utilized heterovalent substitution of divalent lead (Pb 2+ ) with trivalent antimony (Sb 3+ ) to synthesize stable and brightly luminescent Cs 3 Sb 2 Br 9 QDs. The lead-free, full-inorganic QDs were fabricated by a modified ligand-assisted reprecipitation strategy. A photoluminescence quantum yield (PLQY) was determined to be 46% at 410 nm, which was superior to that of other reported halide perovskite QDs. The PL enhancement mechanism was unraveled by surface composition derived quantum-well band structure and their large exciton binding energy. The Br-rich surface and the observed 530 meV exciton binding energy were proposed to guarantee the efficient radiative recombination. In addition, we can also tune the inorganic perovskite QD (Cs 3 Sb 2 X 9 ) emission wavelength from 370 to 560 nm via anion exchange reactions. The developed full-inorganic lead-free Sb-perovskite QDs with high PLQY and stable emission promise great potential for efficient emission candidates.

  1. Identified particle yield associated with a high-$p_T$ trigger particle at the LHC

    CERN Document Server

    Veldhoen, Misha; van Leeuwen, Marco

    Identified particle production ratios are important observables, used to constrain models of particle production in heavy-ion collisions. Measurements of the inclusive particle ratio in central heavy-ion collisions showed an increase of the baryon-to-meson ratio compared to proton-proton collisions at intermediate pT, the so-called baryon anomaly. One possible explanation of the baryon anomaly is that partons from the thermalized deconfined QCD matter hadronize in a different way compared to hadrons produced in a vacuum jet. In this work we extend on previous measurements by measuring particle ratios in the yield associated with a high-pT trigger particle. These measurements can potentially further constrain the models of particle production since they are sensitive to the difference between particles from a jet and particles that are produced in the bulk. We start by developing a particle identification method that uses both the specific energy loss of a particle and the time of flight. From there, we presen...

  2. High-yield water-based synthesis of truncated silver nanocubes

    International Nuclear Information System (INIS)

    Chang, Yun-Min; Lu, I-Te; Chen, Chih-Yuan; Hsieh, Yu-Chi; Wu, Pu-Wei

    2014-01-01

    Highlights: • Development of a water-based formula to fabricate truncated Ag nanocubes. • The sample exhibits (1 0 0), (1 1 0), and (1 1 1) on the facets, edges, and corners. • The sample shows three characteristic absorption peaks due to plasma resonance. -- Abstract: A high-yield water-based hydrothermal synthesis was developed using silver nitrate, ammonia, glucose, and cetyltrimethylammonium bromide (CTAB) as precursors to synthesize truncated silver nanocubes with uniform sizes and in large quantities. With a fixed CTAB concentration, truncated silver nanocubes with sizes of 49.3 ± 4.1 nm were produced when the molar ratio of glucose/silver cation was maintained at 0.1. The sample exhibited (1 0 0), (1 1 0), and (1 1 1) planes on the facets, edges, and corners, respectively. In contrast, with a slightly larger glucose/silver cation ratio of 0.35, well-defined nanocubes with sizes of 70.9 ± 3.8 nm sizes were observed with the (1 0 0) plane on six facets. When the ratio was further increased to 1.5, excess reduction of silver cations facilitated the simultaneous formation of nanoparticles with cubic, spherical, and irregular shapes. Consistent results were obtained from transmission electron microscopy, scanning electron microscopy, X-ray diffraction, and UV–visible absorption measurements

  3. High-yield water-based synthesis of truncated silver nanocubes

    Energy Technology Data Exchange (ETDEWEB)

    Chang, Yun-Min; Lu, I-Te; Chen, Chih-Yuan; Hsieh, Yu-Chi; Wu, Pu-Wei, E-mail: ppwu@mail.nctu.edu.tw

    2014-02-15

    Highlights: • Development of a water-based formula to fabricate truncated Ag nanocubes. • The sample exhibits (1 0 0), (1 1 0), and (1 1 1) on the facets, edges, and corners. • The sample shows three characteristic absorption peaks due to plasma resonance. -- Abstract: A high-yield water-based hydrothermal synthesis was developed using silver nitrate, ammonia, glucose, and cetyltrimethylammonium bromide (CTAB) as precursors to synthesize truncated silver nanocubes with uniform sizes and in large quantities. With a fixed CTAB concentration, truncated silver nanocubes with sizes of 49.3 ± 4.1 nm were produced when the molar ratio of glucose/silver cation was maintained at 0.1. The sample exhibited (1 0 0), (1 1 0), and (1 1 1) planes on the facets, edges, and corners, respectively. In contrast, with a slightly larger glucose/silver cation ratio of 0.35, well-defined nanocubes with sizes of 70.9 ± 3.8 nm sizes were observed with the (1 0 0) plane on six facets. When the ratio was further increased to 1.5, excess reduction of silver cations facilitated the simultaneous formation of nanoparticles with cubic, spherical, and irregular shapes. Consistent results were obtained from transmission electron microscopy, scanning electron microscopy, X-ray diffraction, and UV–visible absorption measurements.

  4. Generation of high-yield insulin producing cells from human bone marrow mesenchymal stem cells.

    Science.gov (United States)

    Jafarian, Arefeh; Taghikhani, Mohammad; Abroun, Saeid; Pourpak, Zahra; Allahverdi, Amir; Soleimani, Masoud

    2014-07-01

    Allogenic islet transplantation is a most efficient approach for treatment of diabetes mellitus. However, the scarcity of islets and long term need for an immunosuppressant limits its application. Recently, cell replacement therapies that generate of unlimited sources of β cells have been developed to overcome these limitations. In this study we have described a stage specific differentiation protocol for the generation of insulin producing islet-like clusters from human bone marrow mesenchymal stem cells (hBM-MSCs). This specific stepwise protocol induced differentiation of hMSCs into definitive endoderm, pancreatic endoderm and pancreatic endocrine cells that expressed of sox17, foxa2, pdx1, ngn3, nkx2.2, insulin, glucagon, somatostatin, pancreatic polypeptide, and glut2 transcripts respectively. In addition, immunocytochemical analysis confirmed protein expression of the above mentioned genes. Western blot analysis discriminated insulin from proinsulin in the final differentiated cells. In derived insulin producing cells (IPCs), secreted insulin and C-peptide was in a glucose dependent manner. We have developed a protocol that generates effective high-yield human IPCs from hBM-MSCs in vitro. These finding suggest that functional IPCs generated by this procedure can be used as a cell-based approach for insulin dependent diabetes mellitus.

  5. High Yield of Adult Oligodendrocyte Lineage Cells Obtained from Meningeal Biopsy

    Directory of Open Access Journals (Sweden)

    Sissi Dolci

    2017-10-01

    Full Text Available Oligodendrocyte loss can lead to cognitive and motor deficits. Current remyelinating therapeutic strategies imply either modulation of endogenous oligodendrocyte precursors or transplantation of in vitro expanded oligodendrocytes. Cell therapy, however, still lacks identification of an adequate source of oligodendrocyte present in adulthood and able to efficiently produce transplantable cells. Recently, a neural stem cell-like population has been identified in meninges. We developed a protocol to obtain high yield of oligodendrocyte lineage cells from one single biopsy of adult rat meningeal tissue. From 1 cm2 of adult rat spinal cord meninges, we efficiently expanded a homogenous culture of 10 millions of meningeal-derived oligodendrocyte lineage cells in a short period of time (approximately 4 weeks. Meningeal-derived oligodendrocyte lineage cells show typical mature oligodendrocyte morphology and express specific oligodendrocyte markers, such as galactosylceramidase and myelin basic protein. Moreover, when transplanted in a chemically demyelinated spinal cord model, meningeal-derived oligodendrocyte lineage cells display in vivo-remyelinating potential. This oligodendrocyte lineage cell population derives from an accessible and adult source, being therefore a promising candidate for autologous cell therapy of demyelinating diseases. In addition, the described method to differentiate meningeal-derived neural stem cells into oligodendrocyte lineage cells may represent a valid in vitro model to dissect oligodendrocyte differentiation and to screen for drugs capable to promote oligodendrocyte regeneration.

  6. 东北春大豆优质高产栽培技术%Soybean High Yield Cultivation Techniques in Northeast in Spring

    Institute of Scientific and Technical Information of China (English)

    马晓莉

    2014-01-01

    Soybean is an important crop widely planted in China, and Northeast China is one of the main planting areas of soybeans. In view of the natural conditions and cropping system of Northeast soybean producing areas, this article reviewed the high quality and high yield cultivation techniques of spring soybeans in the northeast China in terms of species selection, seed treatment, soil preparation, sow-ing, field management, pest control and harvesting.%大豆是我国广泛种植的重要农作物,东北地区是我国大豆主要栽培区之一。针对东北大豆产区的自然条件与耕作栽培制度,从品种选择、种子处理、播前整地、播种、田间管理、病虫害防治及收获几方面进行总结,探讨东北春大豆优质高产栽培技术。

  7. Modeling the complex impacts of timber harvests to find optimal management regimes for Amazon tidal floodplain forests

    Science.gov (United States)

    Fortini, Lucas B.; Cropper, Wendell P.; Zarin, Daniel J.

    2015-01-01

    At the Amazon estuary, the oldest logging frontier in the Amazon, no studies have comprehensively explored the potential long-term population and yield consequences of multiple timber harvests over time. Matrix population modeling is one way to simulate long-term impacts of tree harvests, but this approach has often ignored common impacts of tree harvests including incidental damage, changes in post-harvest demography, shifts in the distribution of merchantable trees, and shifts in stand composition. We designed a matrix-based forest management model that incorporates these harvest-related impacts so resulting simulations reflect forest stand dynamics under repeated timber harvests as well as the realities of local smallholder timber management systems. Using a wide range of values for management criteria (e.g., length of cutting cycle, minimum cut diameter), we projected the long-term population dynamics and yields of hundreds of timber management regimes in the Amazon estuary, where small-scale, unmechanized logging is an important economic activity. These results were then compared to find optimal stand-level and species-specific sustainable timber management (STM) regimes using a set of timber yield and population growth indicators. Prospects for STM in Amazonian tidal floodplain forests are better than for many other tropical forests. However, generally high stock recovery rates between harvests are due to the comparatively high projected mean annualized yields from fast-growing species that effectively counterbalance the projected yield declines from other species. For Amazonian tidal floodplain forests, national management guidelines provide neither the highest yields nor the highest sustained population growth for species under management. Our research shows that management guidelines specific to a region’s ecological settings can be further refined to consider differences in species demographic responses to repeated harvests. In principle, such fine

  8. MULTI-KEV X-Ray Yields From High-Z Gas Targets Fielded At Omega

    International Nuclear Information System (INIS)

    Kane, J.O.; Fournier, K.B.; May, M.J.; Colvin, J.D.; Thomas, C.A.; Marrs, R.E.; Compton, S.M.; Moody, J.D.; Bond, E.J.; Davis, J.F.

    2010-01-01

    The authors report on modeling of x-ray yield from gas-filled targets shot at the OMEGA laser facility. The OMEGA targets were 1.8 mm long, 1.95 mm in diameter Be cans filled with either a 50:50 Ar:Xe mixture, pure Ar, pure Kr or pure Xe at ∼ 1 atm. The OMEGA experiments heated the gas with 20 kJ of 3ω (∼ 350 nm) laser energy delivered in a 1 ns square pulse. the emitted x-ray flux was monitored with the x-ray diode based DANTE instruments in the sub-keV range. Two-dimensional x-ray images (for energies 3-5 keV) of the targets were recorded with gated x-ray detectors. The x-ray spectra were recorded with the HENWAY crystal spectrometer at OMEGA. Predictions are 2D r-z cylindrical with DCA NLTE atomic physics. Models generally: (1) underpredict the Xe L-shell yields; (2) overpredict the Ar K-shell yields; (3) correctly predict the Xe thermal yields; and (4) greatly underpredict the Ar thermal yields. However, there are spreads within the data, e.g. the DMX Ar K-shell yields are correctly predicted. The predicted thermal yields show strong angular dependence.

  9. Highly efficient energy transfer from a carbonyl carotenoid to chlorophyll a in the main light harvesting complex of Chromera velia

    Czech Academy of Sciences Publication Activity Database

    Durchan, Milan; Kesan, G.; Šlouf, M.; Fuciman, M.; Staleva, H.; Tichý, Josef; Litvín, Radek; Bína, David; Vácha, František; Polívka, Tomáš

    2014-01-01

    Roč. 1837, č. 10 (2014), s. 1748-1755 ISSN 0005-2728 R&D Projects: GA ČR(CZ) GAP205/11/1164; GA ČR GBP501/12/G055 Institutional support: RVO:60077344 Keywords : Energy transfer * Light-harvesting * Carbonyl carotenoids Subject RIV: BO - Biophysics Impact factor: 5.353, year: 2014

  10. Produtividade e rendimento do cafeeiro nas cinco primeiras safras irrigado por pivô central em Lavras, MG Coffee yield and production during the initial five harvests under irrigation with center pivot in Lavras, MG

    Directory of Open Access Journals (Sweden)

    Luiz Antônio Lima

    2008-12-01

    foi de 225,6 sc e a média anual de 45,12 sc ha-1, com acréscimo de 119% na produtividade do cafeeiro quando comparada ao tratamento não irrigado, que produziu, em média, 24 sc ha-1 ano-1. O grau de maturação, no momento da colheita, influenciou o rendimento dos tratamentos, sendo os frutos nos estádios cereja e seco, os que mais interferiram no rendimento.Search for sustainability on agricultural exploration and incorporation of new technologies impose the necessity for knowledge and management of main factors related to production, such as irrigation. This experiment evaluated the irrigation effect on yield and production efficiency (amount of beans to produce a bag of 60Kg of coffee irrigated by center pivot in Lavras-MG, Brazil. The experiment was planted with the cultivar Rubi MG-1192, planted on March, 1999. spaced 3.5 meters between rows and 0.8 meters between plants. The experimental design was the one of randomized blocks, with six treatment levels and three replicates. The irrigation was applied at intervals of 2 or 3 days, on Mondays, Wednesdays and Fridays, based on the amount estimated by the water blance considering the class A pan evaporation (ECA and rain depths. The irrigation was calculated as 0% of the difference between ECA and rain depth - 0% ECA (T1, non irrigated, 60% ECA (T2, 80% ECA (T3, 100% ECA (T4, 120% ECA (T5 and 140% ECA (T6. After harvesting the coffee grains from the experimental plots, coffee samples were packed in ventilated plastic bags and dried on wood benches exposed to air long enough to decrease its moisture content between 11 and 12%, gravimetric water content. After drying, the beans were unpeeled and weighed to calculate the yield and production efficiency. Irrigation increased the yield of irrigated plots compared to non irrigated. Although non significant difference was statistically observed when comparing annual yields, the differences were statistically significant when the total production was compared among

  11. EXTREME METEOROLOGICAL CONDITIONS AND METABOLIC PROFILE IN HIGH YIELDING HOLSTEINFRIESIAN DAIRY COWS

    Directory of Open Access Journals (Sweden)

    Z. GERGÁCZ

    2008-10-01

    Full Text Available The impact of two years (2002 and 2003 with different summer temperature extremes on variation in metabolic profile was analyzed in blood and urine samples taken from healthy, primiparous (n = 371 and multiparous (n = 795 high yielding Holstein-Friesian dairy cows. In this study main focus was lead on three most critical physiological phases, thus cows were assigned into three groups as follows: (1 dry cows for 10 days prior to calving; (2 cows 1-30 days after delivery, and (3 cows with more than 31 days post partum. Findings reveal clear response of the cows to heat in selected blood (hemoglobin, plasma aceto-acetic-acid, FFA, AST, glucose, urea and urine (pH, NABE and urea parameters. In the majority of cows, glucose and hemoglobin level, one of the most significant blood parameters, indicated symptoms of insufficient energy supply. Further metabolic indicators differed more or less from reference values depending on actual condition. Due to heat load dry matter intake has been decreased even by 10-15 per cent in primiparous cows. They were expected to increase body weight and size and simultaneously produce attain at large milk yields. In doing so that cows would have require large amount of nutrients. Out of parameters such as hemoglobin, glucose, FFA, AST and blood-urea differed from the reference values in most cases; however, this phenomenon seemed to be present in almost every case for hemoglobin and glucose. The lack of energy caused by heat stress can be contributed to the decrease of dry matter intake which has been indicated by the urea levels and pH both in blood and urine prevailing unfavorable and insufficient feeding practice. The results reconfirm the need to reconsider both the actual feeding practice (e.g. to increase of nutrient content in rations, reduce the intake of soluble proteins in rumen, pay attention of crude fiber in Total Mixed Rations (TMR, NDF and ADF, avoid overfeeding of inorganic buffers, to control moisture

  12. High Photoluminescence Quantum Yields in Organic Semiconductor-Perovskite Composite Thin Films.

    Science.gov (United States)

    Longo, Giulia; La-Placa, Maria-Grazia; Sessolo, Michele; Bolink, Henk J

    2017-10-09

    One of the obstacles towards efficient radiative recombination in hybrid perovskites is a low exciton binding energy, typically in the orders of tens of meV. It has been shown that the use of electron-donor additives can lead to a substantial reduction of the non-radiative recombination in perovskite films. Herein, the approach using small molecules with semiconducting properties, which are candidates to be implemented in future optoelectronic devices, is presented. In particular, highly luminescent perovskite-organic semiconductor composite thin films have been developed, which can be processed from solution in a simple coating step. By tuning the relative concentration of methylammonium lead bromide (MAPbBr 3 ) and 9,9spirobifluoren-2-yl-diphenyl-phosphine oxide (SPPO1), it is possible to achieve photoluminescent quantum yields (PLQYs) as high as 85 %. This is attributed to the dual functions of SPPO1 that limit the grain growth while passivating the perovskite surface. The electroluminescence of these materials was investigated by fabricating multilayer LEDs, where charge injection and transport was found to be severely hindered for the perovskite/SPPO1 material. This was alleviated by partially substituting SPPO1 with a hole-transporting material, 1,3-bis(N-carbazolyl)benzene (mCP), leading to bright electroluminescence. The potential of combining perovskite and organic semiconductors to prepare materials with improved properties opens new avenues for the preparation of simple lightemitting devices using perovskites as the emitter. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  13. Mutation and screening of high-alcoholic-yield yeast by HEPE and optimization of the fermentation condition

    International Nuclear Information System (INIS)

    Han Jingjing; Lu Jiangtao; Zhang Qin; Wang Yan; Fu Yujie; Wang Shilong; Fu Haiying

    2011-01-01

    The Saccharomyces Cerevisiae YE0 was mutated using high-energy-pulse-electron (HEPE) beam. After ethanol stress and determination of the alcohol yield by gas chromatograph, the mutant YF1 with high alcoholic yield was obtained. The results showed that under the optimized fermentation conditions (34 degree C as the fermentation temperature, 72 h as the fermentation time and 30% as the glucose concentration), the alcoholic yield of YF1 was 15.57% which was 58.23% higher than that of the original strain YE0 (9.84%) under the same conditions. The growth rate and lethal temperature of the mutant YF1 were obviously enhanced to the original strain YE0. The mutant YF1 has a great potential application in industrial production of alcohol. And it can also be used as the original strain for further mutagenesis to get the strain of higher alcoholic yield. (authors)

  14. [Effects of nitrogen application level on soil nitrate accumulation and ammonia volatilization in high-yielding wheat field].

    Science.gov (United States)

    Wang, Dong; Yu, Zhenwen; Yu, Wenming; Shi, Yu; Zhou, Zhongxin

    2006-09-01

    The study showed that during the period from sowing to pre-wintering, the soil nitrate in high-yielding wheat field moved down to deeper layers, and accumulated in the layers below 140 cm. An application rate of 96-168 kg N x hm(-2) increased the nitrate content in 0-60 cm soil layer and the wheat grain yield and its protein content, and decreased the proportion of apparent N loss to applied N and the ammonia volatilization loss from basal nitrogen. Applying 240 kg N x hm(-2) promoted the downward movement of soil nitrate and its accumulation in deeper layers, increased the proportion of apparent N loss to applied N and the ammonia volatilization loss from basal nitrogen, had no significant effect on the protein content of wheat grain, but decreased the grain yield. The appropriate application rate of nitrogen on high-yielding wheat field was 132-204 kg N x hm(-2).

  15. A Low-cost, High-yield Process for the Direct Productin of High Energy Density Liquid Fuel from Biomass

    Energy Technology Data Exchange (ETDEWEB)

    Agrawal, Rakesh [Purdue Univ., West Lafayette, IN (United States); Delgass, W. N. [Purdue Univ., West Lafayette, IN (United States); Ribeiro, F. [Purdue Univ., West Lafayette, IN (United States)

    2013-08-31

    The primary objective and outcome of this project was the development and validation of a novel, low-cost, high-pressure fast-hydropyrolysis/hydrodeoxygenation (HDO) process (H2Bioil) using supplementary hydrogen (H2) to produce liquid hydrocarbons from biomass. The research efforts under the various tasks of the project have culminated in the first experimental demonstration of the H2Bioil process, producing 100% deoxygenated >C4+ hydrocarbons containing 36-40% of the carbon in the feed of pyrolysis products from biomass. The demonstrated H{sub 2}Bioil process technology (i.e. reactor, catalyst, and downstream product recovery) is scalable to a commercial level and is estimated to be economically competitive for the cases when supplementary H2 is sourced from coal, natural gas, or nuclear. Additionally, energy systems modeling has revealed several process integration options based on the H2Bioilprocess for energy and carbon efficient liquid fuel production. All project tasks and milestones were completed or exceeded. Novel, commercially-scalable, high-pressure reactors for both fast-hydropyrolysis and hydrodeoxygenation were constructed, completing Task A. These reactors were capable of operation under a wide-range of conditions; enabling process studies that lead to identification of optimum process conditions. Model compounds representing biomass pyrolysis products were studied, completing Task B. These studies were critical in identifying and developing HDO catalysts to target specific oxygen functional groups. These process and model compound catalyst studies enabled identification of catalysts that achieved 100% deoxygenation of the real biomass feedstock, sorghum, to form hydrocarbons in high yields as part of Task C. The work completed during this grant has identified and validated the novel and commercially scalable H2Bioil process for production of hydrocarbon fuels from biomass. Studies on

  16. Harvesting and replenishment policies for renewable natural resources

    Science.gov (United States)

    Douglas, Aaron J.; Johnson, Richard L.

    1993-01-01

    The current paper links the optimal intertemporal use of renewable natural resources to the harvesting activities of various economic agents. Previous contributions cite market forces as a causative factor inducing the extirpation of renewable natural resources. The analysis given here discusses investment in the stock of renewable resources and cites important examples of this activity. By introducing joint harvesting and replenishment strategies into a model of renewable resource use, the analysis adds descriptive reality and relevance to positive and normative discussions of renewable natural resource use. A high price for the yield or a high discount rate tend to diminish the size of the optimum stationary stock of the resource with a non-replenishment harvesting strategy. Optimal non-replenishment harvesting strategies for renewable natural resources will exhaustion or extirpation of the resource if the price of the yield or the discount rate are sufficiently large. However, the availability of a replenishment technology and the use of replenishment activities tends to buffer the resource against exhaustion or extirpation.

  17. Effects of location and year on grain yield and its components in wheat genotypes developed from seed irradiation treatment

    International Nuclear Information System (INIS)

    Amer, I.M.; El-Rassas, H.N.; Abdel-Aleem, M.M.

    1994-01-01

    Eight mutant lines derived from gamma ray treatments and their parental cultivar sokha 69 of bread wheat were evaluated for grain yield per feddan, straw yield per feddan, harvest index, spike length, spike yield and weight of 1000-kernels at two locations (El-Fayoum and Inshas) in two seasons, 1991/92 and 1992/93. Significant effects of location on yield and yield components were found and the year significantly affects all the studied traits except grain yield per feddan. A significant location genotype interaction was detected for spike length, 1000-kernel weight and straw yield per feddan. In addition, year genotype interaction was significant in weight of 1000-kernels, straw yield per feddan and harvest index. The statistical analysis showed a significant difference among genotypes over all environments for spike length, 1000-kernel weight, straw yield per feddan and harvest index. However, these did not reflect significant effect on grain yield per feddan over all environments because it has a highly compensation ability. Meanwhile, mutant L 1 2 -1 exhibited significantly higher straw yield than sokha 69, when averaged over two seasons at El-Fayoum. Mutant L 1 9 -1 gave higher weight of 1000-kernels, spike length and harvest index than the other genotypes at low-yielding location (Inshas). It seems to be stable over a wide range of environments. 3 tabs

  18. Enhancement of Biogas Yield of Poplar Leaf by High-Solid Codigestion with Swine Manure.

    Science.gov (United States)

    Wangliang, Li; Zhikai, Zhang; Guangwen, Xu

    2016-05-01

    The aim of this work was to examine the improvement of anaerobic biodegradability of organic fractions of poplar leaf from codigestion with swine manure (SM), thus biogas yield and energy recovery. When poplar leaf was used as a sole substrate, the cumulative biogas yield was low, about 163 mL (g volatile solid (VS))(-1) after 45 days of digestion with a substrate/inoculum ratio of 2.5 and a total solid (TS) of 22 %. Under the same condition, the cumulative biogas yield of poplar leaf reached 321 mL (g VS)(-1) when SM/poplar leaf ratio was 2:5 (based on VS). The SM/poplar leaf ratio can determine C/N ratio of the cosubstrate and thus has significant influence on biogas yield. When the SM/poplar leaf ratio was 2:5, C/N ratio was calculated to be 27.02, and the biogas yield in 45 days of digestion was the highest. The semi-continuous digestion of poplar leaf was carried out with the organic loading rate of 1.25 and 1.88 g VS day(-1). The average daily biogas yield was 230.2 mL (g VS)(-1) and 208.4 mL (g VS)(-1). The composition analysis revealed that cellulose and hemicellulose contributed to the biogas production.

  19. Air-insufflated high-definition dacryoendoscopy yields significantly better image quality than conventional dacryoendoscopy

    Directory of Open Access Journals (Sweden)

    Sasaki T

    2017-08-01

    -insufflated HDD is safe, and yields significantly better image quality than CD and saline-irrigated HDD. Keywords: pressure-controlled air-insufflated, high-definition dacryoendoscopy, saline-irrigated dacryoendoscopy, emphysema

  20. High diagnostic yield of syndromic intellectual disability by targeted next-generation sequencing.

    Science.gov (United States)

    Martínez, Francisco; Caro-Llopis, Alfonso; Roselló, Mónica; Oltra, Silvestre; Mayo, Sonia; Monfort, Sandra; Orellana, Carmen

    2017-02-01

    Intellectual disability is a very complex condition where more than 600 genes have been reported. Due to this extraordinary heterogeneity, a large proportion of patients remain without a specific diagnosis and genetic counselling. The need for new methodological strategies in order to detect a greater number of mutations in multiple genes is therefore crucial. In this work, we screened a large panel of 1256 genes (646 pathogenic, 610 candidate) by next-generation sequencing to determine the molecular aetiology of syndromic intellectual disability. A total of 92 patients, negative for previous genetic analyses, were studied together with their parents. Clinically relevant variants were validated by conventional sequencing. A definitive diagnosis was achieved in 29 families by testing the 646 known pathogenic genes. Mutations were found in 25 different genes, where only the genes KMT2D, KMT2A and MED13L were found mutated in more than one patient. A preponderance of de novo mutations was noted even among the X linked conditions. Additionally, seven de novo probably pathogenic mutations were found in the candidate genes AGO1, JARID2, SIN3B, FBXO11, MAP3K7, HDAC2 and SMARCC2. Altogether, this means a diagnostic yield of 39% of the cases (95% CI 30% to 49%). The developed panel proved to be efficient and suitable for the genetic diagnosis of syndromic intellectual disability in a clinical setting. Next-generation sequencing has the potential for high-throughput identification of genetic variations, although the challenges of an adequate clinical interpretation of these variants and the knowledge on further unknown genes causing intellectual disability remain to be solved. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

  1. A multi-region assessment of population rates of cardiac catheterization and yield of high-risk coronary artery disease

    Directory of Open Access Journals (Sweden)

    Clement Fiona M

    2011-11-01

    Full Text Available Abstract Background There is variation in cardiac catheterization utilization across jurisdictions. Previous work from Alberta, Canada, showed no evidence of a plateau in the yield of high-risk disease at cardiac catheterization rates as high as 600 per 100,000 population suggesting that the optimal rate is higher. This work aims 1 To determine if a previously demonstrated linear relationship between the yield of high-risk coronary disease and cardiac catheterization rates persists with contemporary data and 2 to explore whether the linear relationship exists in other jurisdictions. Methods Detailed clinical information on all patients undergoing cardiac catheterization in 3 Canadian provinces was available through the Alberta Provincial Project for Outcomes Assessment in Coronary Heart (APPROACH disease and partner initiatives in British Columbia and Nova Scotia. Population rates of catheterization and high-risk coronary disease detection for each health region in these three provinces, and age-adjusted rates produced using direct standardization. A mixed effects regression analysis was performed to assess the relationship between catheterization rate and high-risk coronary disease detection. Results In the contemporary Alberta data, we found a linear relationship between the population catheterization rate and the high-risk yield. Although the yield was slightly less in time period 2 (2002-2006 than in time period 1(1995-2001, there was no statistical evidence of a plateau. The linear relationship between catheterization rate and high-risk yield was similarly demonstrated in British Columbia and Nova Scotia and appears to extend, without a plateau in yield, to rates over 800 procedures per 100,000 population. Conclusions Our study demonstrates a consistent finding, over time and across jurisdictions, of linearly increasing detection of high-risk CAD as population rates of cardiac catheterization increase. This internationally-relevant finding

  2. New approach to increasing rice lodging resistance and biomass yield through the use of high gibberellin producing varieties.

    Directory of Open Access Journals (Sweden)

    Ayako Okuno

    Full Text Available Traditional breeding for high-yielding rice has been dependent on the widespread use of fertilizers and the cultivation of gibberellin (GA-deficient semi-dwarf varieties. The use of semi-dwarf plants facilitates high grain yield since these varieties possess high levels of lodging resistance, and thus could support the high grain weight. Although this approach has been successful in increasing grain yield, it is desirable to further improve grain production and also to breed for high biomass. In this study, we re-examined the effect of GA on rice lodging resistance and biomass yield using several GA-deficient mutants (e.g. having defects in the biosynthesis or perception of GA, and high-GA producing line or mutant. GA-deficient mutants displayed improved bending-type lodging resistance due to their short stature; however they showed reduced breaking-type lodging resistance and reduced total biomass. In plants producing high amounts of GA, the bending-type lodging resistance was inferior to the original cultivars. The breaking-type lodging resistance was improved due to increased lignin accumulation and/or larger culm diameters. Further, these lines had an increase in total biomass weight. These results show that the use of rice cultivars producing high levels of GA would be a novel approach to create higher lodging resistance and biomass.

  3. New approach to increasing rice lodging resistance and biomass yield through the use of high gibberellin producing varieties.

    Science.gov (United States)

    Okuno, Ayako; Hirano, Ko; Asano, Kenji; Takase, Wakana; Masuda, Reiko; Morinaka, Yoichi; Ueguchi-Tanaka, Miyako; Kitano, Hidemi; Matsuoka, Makoto

    2014-01-01

    Traditional breeding for high-yielding rice has been dependent on the widespread use of fertilizers and the cultivation of gibberellin (GA)-deficient semi-dwarf varieties. The use of semi-dwarf plants facilitates high grain yield since these varieties possess high levels of lodging resistance, and thus could support the high grain weight. Although this approach has been successful in increasing grain yield, it is desirable to further improve grain production and also to breed for high biomass. In this study, we re-examined the effect of GA on rice lodging resistance and biomass yield using several GA-deficient mutants (e.g. having defects in the biosynthesis or perception of GA), and high-GA producing line or mutant. GA-deficient mutants displayed improved bending-type lodging resistance due to their short stature; however they showed reduced breaking-type lodging resistance and reduced total biomass. In plants producing high amounts of GA, the bending-type lodging resistance was inferior to the original cultivars. The breaking-type lodging resistance was improved due to increased lignin accumulation and/or larger culm diameters. Further, these lines had an increase in total biomass weight. These results show that the use of rice cultivars producing high levels of GA would be a novel approach to create higher lodging resistance and biomass.

  4. High yield purification of full-length functional hERG K+ channels produced in Saccharomyces cerevisiae

    DEFF Research Database (Denmark)

    Molbaek, Karen; Scharff-Poulsen, Peter; Hélix-Nielsen, Claus

    2015-01-01

    knowledge this is the first reported high-yield production and purification of full length, tetrameric and functional hERG. This significant breakthrough will be paramount in obtaining hERG crystal structures, and in establishment of new high-throughput hERG drug safety screening assays....

  5. Subtle spectral effects accompanying the assembly of bacteriochlorophylls into cyclic light harvesting complexes revealed by high-resolution fluorescence spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Rätsep, Margus, E-mail: margus.ratsep@ut.ee; Pajusalu, Mihkel, E-mail: mihkel.pajusalu@ut.ee; Linnanto, Juha Matti, E-mail: juha.matti.linnanto@ut.ee [Institute of Physics, University of Tartu, Riia 142, 51014 Tartu (Estonia); Freiberg, Arvi, E-mail: arvi.freiberg@ut.ee [Institute of Physics, University of Tartu, Riia 142, 51014 Tartu, Estonia and Institute of Molecular and Cell Biology, University of Tartu, Riia 23, 51010 Tartu (Estonia)

    2014-10-21

    We have observed that an assembly of the bacteriochloropyll a molecules into B850 and B875 groups of cyclic bacterial light-harvesting complexes LH2 and LH1, respectively, results an almost total loss of the intra-molecular vibronic structure in the fluorescence spectrum, and simultaneously, an essential enhancement of its phonon sideband due to electron-phonon coupling. While the suppression of the vibronic coupling in delocalized (excitonic) molecular systems is predictable, as also confirmed by our model calculations, a boost of the electron-phonon coupling is rather unexpected. The latter phenomenon is explained by exciton self-trapping, promoted by mixing the molecular exciton states with charge transfer states between the adjacent chromophores in the tightly packed B850 and B875 arrangements. Similar, although less dramatic trends were noted for the light-harvesting complexes containing chlorophyll pigments.

  6. A combined flamer-cultivator for weed control during the harvesting season of asparagus green spears

    International Nuclear Information System (INIS)

    Martelloni, L.; Fontanelli, M.; Frasconi, C.; Raffaelli, M.; Pirchio, M.; Peruzzi, A.

    2017-01-01

    Weed competition during spears harvesting reduces asparagus yields. The application of herbicides during this period is illegal, and alternative non-chemical practices are needed. This research tested the effectiveness and efficiency of a custom-built combined flamer-cultivator to control weeds (both in the inter- and intra- spears production bands) during the spears harvest season. It also analysed the effects of various liquefied petroleum gas (LPG) doses on total asparagus yield, mean spear weight, and total number of marketable spears. In both years, the asparagus spears were generally not damaged by flame weeding using LPG doses of between 43 to 87 kg/ha. The same LPG doses were effective in controlling weeds, showing the same total marketable yields as the weed-free control. At high LPG doses (e.g. 130 and 260 kg/ha), yields decreased as a consequence of the damage caused to the spears, resulting in a lower number of marketable spears. Flaming did not affect the mean spear weight, and can be applied repeatedly during harvesting to maintain the weeds at a level that does not lead to a yield reduction. The repeated use of the combined flamer-cultivator (every seven days) led to higher yields than plots where weed control was not conducted. The new machine can be used in a period when herbicides are not possible. Flaming could be introduced by asparagus producers as an alternative, or in addition to herbicides applied in the pre-emergence and post-harvest of spears.

  7. A combined flamer-cultivator for weed control during the harvesting season of asparagus green spears

    Energy Technology Data Exchange (ETDEWEB)

    Martelloni, L.; Fontanelli, M.; Frasconi, C.; Raffaelli, M.; Pirchio, M.; Peruzzi, A.

    2017-07-01

    Weed competition during spears harvesting reduces asparagus yields. The application of herbicides during this period is illegal, and alternative non-chemical practices are needed. This research tested the effectiveness and efficiency of a custom-built combined flamer-cultivator to control weeds (both in the inter- and intra- spears production bands) during the spears harvest season. It also analysed the effects of various liquefied petroleum gas (LPG) doses on total asparagus yield, mean spear weight, and total number of marketable spears. In both years, the asparagus spears were generally not damaged by flame weeding using LPG doses of between 43 to 87 kg/ha. The same LPG doses were effective in controlling weeds, showing the same total marketable yields as the weed-free control. At high LPG doses (e.g. 130 and 260 kg/ha), yields decreased as a consequence of the damage caused to the spears, resulting in a lower number of marketable spears. Flaming did not affect the mean spear weight, and can be applied repeatedly during harvesting to maintain the weeds at a level that does not lead to a yield reduction. The repeated use of the combined flamer-cultivator (every seven days) led to higher yields than plots where weed control was not conducted. The new machine can be used in a period when herbicides are not possible. Flaming could be introduced by asparagus producers as an alternative, or in addition to herbicides applied in the pre-emergence and post-harvest of spears.

  8. High-yield production of mannitol by Leuconostoc pseudomesenteroides CTCC G123 from chicory-derived inulin hydrolysate.

    Science.gov (United States)

    Zhang, Min; Gu, Lei; Cheng, Chao; Zhu, Junru; Wu, Hao; Ma, Jiangfeng; Dong, Weiliang; Kong, Xiangping; Jiang, Min; Ouyang, Pingkai

    2017-08-01

    Chicory is an agricultural plant with considerable potential as a carbohydrate substrate for low-cost production of biochemicals. In this work, the production of mannitol by Leuconostoc pseudomesenteroides CTCC G123 from chicory-derived inulin hydrolysate was investigated. The bioconversion process initially suffered from the leakage of fructose to the phosphoketolase pathway, resulting in a low mannitol yield. When inulin hydrolysate was supplemented with glucose as a substrate for mannitol production in combination with aeration induction and nicotinic acid induced redox modulation strategies, the mannitol yield greatly improved. Under these conditions, significant improvement in the glucose consumption rate, intracellular NADH levels and mannitol dehydrogenase specific activity were observed, with mannitol production increasing from 64.6 to 88.1 g/L and overall yield increase from 0.69 to 0.94 g/g. This work demonstrated an efficient method for the production of mannitol from inulin hydrolysate with a high overall yield.

  9. REVISITED GRAIN HARVESTERS PARAMETERS SUBSTATIATION AND EFFECTIVENESS OF THEM

    Directory of Open Access Journals (Sweden)

    G. G. Maslov

    2016-01-01

    Full Text Available Impact of cereal crops yield on the actual strow content in heap mass was studied. Its distribution interval is from 0.6 to 1.2 in the range of yields from 3 to 12 t/ha. Regularity of strow content decline and productivity increase at the same time is confirmed by the Cochran criterion (its estimated value of 0.56 is less than the table one of 0.62. A strow content low facilitates the harvesters’ operation. The required for the operation process harvesters engine power is different depending on schemes of threshing-separating machine with the rotary and beater threshing drums. The authors proved adequacy of the obtained mathematical models of dependence of the engine power from harvester delivery capacity. For the combines with classical technological scheme the calculated value of Fisher criterion is 0.75. For combines with an axial rotary threshing-separating device the table value of 0.8 criterion is also higher than the estimated one of 0.66.The obtained results of the required power calculations at various methodological approaches were close to results convergence exceeding 10 percent, which confirms objectivity of them. The technological and economic efficiency of the rotary harvesters compared with classical scheme is better. It is obtained due to the higher specific bandwidth, low grain crushing and micro damage. If a harvester has the threshing-separating device with axial rotor scheme, so grain crushing is much less(no more than 0.5-0.6 percent, which also improves economic parameters. But at operation of combines with the classical scheme the share of broken grain makes 4-6 percent that sharply raises indirect losses of a harvest. We recommend when the combine fleet renovation шт agricultural enterprises to introduce 1.5-2 times high-performance harvesters with axial rotor scheme.

  10. Selection of common bean inbred lines with tolerance to high moisture at harvest Seleção de linhagens de feijão com tolerância a alta umidade no momento da colheita

    Directory of Open Access Journals (Sweden)

    Lidiane Kely de Lima

    2013-04-01

    Full Text Available The occurrence of precipitation / rain in harvest bean causes damage to the product and reduces the yield. The main alternative to mitigate this problem is to obtain cultivars presenting low germination of beans in the pods under conditions of high moisture. The purpose of this study was to verify if there is genetic variability among the common bean inbred lines that are in the phase of recommendation for the South of Minas Gerais, Brazil in regard to tolerance to moisture after harvest, and identify traits that may be routinely used in selection of tolerant lines to these conditions. Ninety-five lines in the phase of recommendation by the Genetic Breeding Program from UFLA were used. After harvest, a sample of plants from each plot was removed for assessments of seed germination in the pods in a moist chamber and water absorption by pod and seed. Eight days after harvest, another sample was removed to assess seed appearance using a scoring scale. The data were submitted to analysis of variance and estimates of the Pearson phenotypic correlations were obtained among traits. Lines differ in relation to tolerance to moisture at the time of harvest, with those of higher tolerance having lighter colored seeds. The main difficulty in selection of common bean lines for tolerance to high moisture at harvest is the repeatability of the environmental conditions among crop seasons. The alternative is assessing the amount of water absorbed by pods.A ocorrência de precipitação / chuva na colheita do feijão comum provoca danos ao produto e reduz o rendimento. A principal alternativa para mitigar este problema é a obtenção de cultivares com baixa germinação de grãos nas vagens em condições de alta umidade. Neste trabalho, objetivou-se vrificar se há variabilidade genética entre as linhagens do feijoeiro que estão em fase de recomendação para o Sul de Minas Gerais quanto à tolerância à umidade após a colheita e identificar caracteres que

  11. Effects of Lignocellulosic Compounds on the Yield, Nanostructure and Reactivity of Soot from Fast Pyrolysis at High Temperatures

    DEFF Research Database (Denmark)

    Trubetskaya, Anna; Broström, Markus; Kling, Jens

    reactor. The specific objectives of this study were to: (1) obtain knowledge about lignocellulosic compounds and monolignols influence on the yield, nanostructure, composition, and reactivity of soot during high-temperature gasification, (2) understand the influence of Soxhlet extraction on the soot......Gasification offers the utilization of biomass to a wide variety of applications such as heat, electricity, chemicals and transport fuels in an efficient and sustainable manner. High soot yields in the high-temperature entrained flow gasification lead to intensive gas cleaning and can cause...... primary, secondary and teriary pyrolysis products such as organic acids, aldehydes and phenolics [1]. In this study, therefore, the impacts of lignocellulosic compounds and monolignols (syringol, guaiacol, p-hydroxyphenol) on the yield and characteristics of soot were investigated at 1250°C in a drop tube...

  12. Induction of resistance to bacterial leaf blight (Xanthomonas oryzae) disease in the high yielding variety Vijaya (IR 8 x T 90)

    International Nuclear Information System (INIS)

    Padmanabhan, S.Y.; Kaur, S.; Rao, M.

    1976-01-01

    The high-yield variety Vijaya ( IR 8 x T 90), susceptible to bacterial leaf blight (Xanthomonas oryzae, Uyeda and Ishiyama Dawson), was treated with EMS to induce resistance. Dehusked seeds were pre-soaked in distilled water for 4 hrs, and subjected to 0.1% and 0.2% EMS for 6 hrs. Seed germination and survival was low in 0.2% EMS. Seedlings of M 1 were raised in pots, and panicles of individual plants harvested separately. The seeds of M 2 (8800 plants) generation were grown in nursery beds, and transplanted in field after 30 days. The plants were inoculated at the boot leaf stage with X.oryzae by the clipping method, and lesion length measured 15 days later. The frequency distribution of controls was bimodal, the EMS-treated population polymodal with new peaks. A wider range of variability was induced on the resistant and susceptible side. In M 2 0.36% resistant and 0.62% moderately resistant plants occurred. The seeds of (11) resistant and (20) moderately resistant plants of M 2 were sown for M 3 generation. These plants also segregated in the range of 0-31 and 0-32 cm lesion length. The frequency distribution curve was polymodal. M 2 from ''R'' showed 1.07% of resistant plants and 0.42% from ''MR'', against, 4.28% of moderately resistant plants from ''R'' and 3.22% from ''MR''. Susceptible plants of M 2 also segregated towards resistance (1.15%) and moderately resistant (6.96%) plants in M 3 generation. Resistant (25) and moderately resistant (147) plants of M 3 were carried forward to M 4 generation, and segregated in the range of 2.1-25 cm lesion length. The frequency curve was polymodal. No resistant plant (up to 2.0 cm lesion length) could be isolated in M 4 . The percentage of moderately resistant plants was 4.44% from ''R'' of M 3 and 4.82% from ''MR'' of M 3 and 4.77% from ''S'' of M 3 generation. The yield of resistant plants was low whereas the yield of moderately resistant plants equalled the parent; the yield of susceptible segregants equalled or

  13. Mems-based pzt/pzt bimorph thick film vibration energy harvester

    DEFF Research Database (Denmark)

    Xu, Ruichao; Lei, Anders; Dahl-Petersen, Christian

    2011-01-01

    We describe fabrication and characterization of a significantly improved version of a MEMS-based PZT/PZT thick film bimorph vibration energy harvester with an integrated silicon proof mass. The main advantage of bimorph vibration energy harvesters is that strain energy is not lost in mechanical...... support materials since only PZT is strained, and thus it has a potential for significantly higher output power. An improved process scheme for the energy harvester resulted in a robust fabrication process with a record high fabrication yield of 98.6%. Moreover, the robust fabrication process allowed...... a high pressure treatment of the screen printed PZT thick films prior to sintering, improving the PZT thick film performance and harvester power output reaches 37.1 μW at 1 g....

  14. Fabrication and characterization of MEMS-based PZT/PZT bimorph thick film vibration energy harvesters

    DEFF Research Database (Denmark)

    Xu, Ruichao; Lei, Anders; Dahl-Petersen, Christian

    2012-01-01

    We describe the fabrication and characterization of a significantly improved version of a microelectromechanical system-based PZT/PZT thick film bimorph vibration energy harvester with an integrated silicon proof mass; the harvester is fabricated in a fully monolithic process. The main advantage...... yield of 98%. The robust fabrication process allowed a high pressure treatment of the screen printed PZT thick films prior to sintering. The high pressure treatment improved the PZT thick film performance and increased the harvester power output to 37.1 μW at 1 g root mean square acceleration. We also...... characterize the harvester performance when only one of the PZT layers is used while the other is left open or short circuit....

  15. New high yielding mutant varieties of mustard (Brassica campestris L. var. yellow sarson)

    International Nuclear Information System (INIS)

    Rahman, A.; Das, M.L.; Pathan, A.J.

    1992-01-01

    Mutation breeding work at the Bangladesh Institute of Nuclear Agriculture has been successful with the development of a number of promising mutants and with the release of two mutant varieties of mustard (Brassica campestris L. var. Yellow Sarson), Agrani and Safal, for commercial cultivation in Bangladesh. The mutant varieties have higher seed and oil yield with higher biomass production, tolerance to Alternaria blight and aphid under field conditions. The average seed yield of the varieties is 1726 and 1754 kg/ha as compared to 1447 kg/ha of the best check Sonali. These varieties have 42-43 per cent oil in the seed. (author). 7 refs., 3 tabs

  16. Ultrastable green fluorescence carbon dots with a high quantum yield for bioimaging and use as theranostic carriers

    DEFF Research Database (Denmark)

    Yang, Chuanxu; Thomsen, Rasmus Peter; Ogaki, Ryosuke

    2015-01-01

    to widely used semiconductor quantum dots. However, it remains a great challenge to prepare highly stable, water-soluble green luminescent Cdots with a high quantum yield. Herein we report a new synthesis route for green luminescent Cdots imbuing these desirable properties and demonstrate their potential...... in biomedical applications. Oligoethylenimine (OEI)–β-cyclodextrin (βCD) Cdots were synthesised using a simple and fast heating method in phosphoric acid. The synthesised Cdots showed strong green fluorescence under UV excitation with a 30% quantum yield and exhibited superior stability over a wide pH range. We...

  17. Selection of High Oil Yielding Trees of Millettia pinnata (L.) Panigrahi, Vegetative Propagation and Growth in the Field

    OpenAIRE

    Ni Luh Arpiwi; I Made Sutha Negara; I Nengah Simpen

    2017-01-01

    Millettia pinnata (L.) Panigrahi is a potential legume tree that produces seed oil for biodiesel feedstock. The initial step for raising a large-scale plantation of the species is selection of high oil yielding trees from the natural habitat. This is followed by vegetative propagation of the selected trees and then testing the growth of the clone in the field. The aim of the present study was to select high-oil yielding trees of M. pinnata, to propagate the selected trees by budding and to e...

  18. High yield of culture-based diagnosis in a TB-endemic setting

    NARCIS (Netherlands)

    Demers, Anne-Marie; Verver, Suzanne; Boulle, Andrew; Warren, Robin; van Helden, Paul; Behr, Marcel A.; Coetzee, David

    2012-01-01

    Background: In most of the world, microbiologic diagnosis of tuberculosis (TB) is limited to microscopy. Recent guidelines recommend culture-based diagnosis where feasible. Methods: In order to evaluate the relative and absolute incremental diagnostic yield of culture-based diagnosis in a

  19. The Eel River, northwestern California; high sediment yields from a dynamic landscape

    Science.gov (United States)

    Thomas E. Lisle

    1990-01-01

    The Eel River draining the Coast Range of northwestern California has the highest recorded average suspended sediment yield per drainage area of any river of its size or larger unaffected by volcanic eruptions or active glaciers in the conterminous United States (1,720 t/km 2 yr from 9,390 km 2 ; Brown and Ritter, 1971).

  20. Predicting yields of high priced trimmed beef cuts by means of ...

    African Journals Online (AJOL)

    The linear models included carcass weight and visual assessment of fatness and conformation by means of seven fat and five conformation classes. Amount of variation accounted for (R2) was the most favourable for total yield (87.3%) and the least favourable for the rib-eye cut (43.5%). Carcass weight contributed to most ...

  1. High-yielding cascade enzymatic synthesis of 5-methyluridine using a novel combination of nucleoside phosphorylases

    CSIR Research Space (South Africa)

    Visser, Daniel F

    2010-07-01

    Full Text Available and thymine. A 5-methyluridine yield of 79% on guanosine was achieved in a reaction slurry at a 53 mM (1.5% w/w) guanosine concentration. 5-Methyluridine is an intermediate in synthetic routes to thymidine and the antiretroviral drugs zidovudine...

  2. semi-dwarf tef lines for high seed yield and lodging tolerance

    African Journals Online (AJOL)

    ACSS

    Three genotypes, namely RIL- 91, RIL-244 and RIL-11, gave the highest seed yield, ranging between 4.4 to 4.7 t ha-1, compared to .... lodging tolerant tef varieties, adapting to the changing ..... moisture stress areas (Tsedey) was grouped.

  3. Response of high yielding rice varieties to NaCl salinity in ...

    African Journals Online (AJOL)

    STORAGESEVER

    2008-11-05

    Nov 5, 2008 ... the percentage of fertility, stem weight and white grain weight (Kavousi, 1995). ... yield falling in accordance with rising salinity or electrical conduction of ... Due to the effect of salinity on height reduction and its significant effect ..... leaf elongation in maize Is not Mediated by changes in cell wall. Acidification ...

  4. N-(m-[125I]iodophenyl)maleimide: an agent for high yield radiolabeling of antibodies

    International Nuclear Information System (INIS)

    Khawli, L.A.; Van den Abbeele, A.D.; Kassis, A.I.

    1992-01-01

    In an effort to radiolabel antibodies, N-(m-[ 125 I]iodophenyl)maleimide (m-[ 125 I]IPM) was prepared by the demetallation of an N-[m-tri-(n-butyl)stannylphenyl]maleimide intermediate. The unlabeled intermediate was synthesized in ≥ 75% yield using a palladium catalyzed reaction of hexabutylditin with m-bromoaniline, followed by reaction with maleic anhydride and ring annulation. All products were confirmed by NMR and elemental analysis. Labeling with 125 I was carried out in a biphasic mixture containing chloramine-T (radiochemical yield ≥ 70%). Rabbit IgG modified with the heterobifunctional crosslinking agent N-succinimidyl-3-(2-pyridyldithio)propionate (SPDP) and bovine serum albumin were conjugated with m-[ 125 I]IPM (yield: 40 and 80%, respectively). In addition, m-[ 125 I]IPM was conjugated to rabbit IgG subunits (HL) in 70% yield. The in vitro stability of the radiolabeled proteins in serum showed < 1% deiodination over 24h. (author)

  5. Factors affecting the size of ovulatory follicles and conception rate in high-yielding dairy cows.

    Science.gov (United States)

    Mokhtari, A; Kafi, M; Zamiri, M J; Akbari, R

    2016-03-01

    Two studies were designed to determine (1) the effects of Heatsynch and Ovsynch protocols versus spontaneous ovulation and (2) the effects of calving problems, clinical uterine infections, and clinical mastitis on the size of the ovulatory follicle, conception rate, and embryonic/fetal (E/F) death in high-yielding dairy cows. In study 1, cows without the history of calving problems, clinical uterine infections, and clinical mastitis were randomly allocated to either an Ovsynch (n = 45) or Heatsynch (n = 39) ovulation synchronization protocol or spontaneous ovulation (n = 43) groups. Blood samples were collected on the day of artificial insemination (AI) to measure progesterone (P4), estradiol-17β, and insulin-like growth factor 1 (IGF-1) and 7 days later to measure P4. Study 2 consisted of cows (n = 351) with or without the history of calving problems, clinical uterine infections, and clinical mastitis which were artificially inseminated after a 55-day voluntary waiting period. Transrectal ultrasonography was performed at the time of AI to measure the ovulatory follicle size and on Days 30 and 68 after AI to diagnose pregnancy in both studies. In study 1, the mean (±standard error of the mean) diameter of the ovulatory follicle was greater (P = 0.0005) and E/F mortality was lower (P = 0.007) for the spontaneous ovulation group compared with Ovsynch and Heatsynch groups. Serum concentration of P4 on Day 7 after AI was correlated with the size of the ovulatory follicle (P = 0.007). Conception rate at Days 30 and 68 was not significantly different between the three experimental groups in study 1. Cows with serum IGF-1 concentrations greater than 55 ng/mL at AI had significantly higher Day 68 conception rate (50% vs. 24%) and lower E/F death (16.6% vs. 40%) compared to cows with serum IGF-1 concentrations lower than 56 ng/mL at AI. The conception rate on Days 30 and 68 for follicles of 10 to 14 mm in diameter (34% and 21.8%) was significantly lower than follicles of

  6. Innovations in papermaking: An LCA of printing and writing paper from conventional and high yield pulp

    International Nuclear Information System (INIS)

    Manda, B.M. Krishna; Blok, Kornelis; Patel, Martin K.

    2012-01-01

    Pulp and paper industry is facing challenges such as resource scarcity and greenhouse gas (GHG) emissions. The objective of this research is to investigate whether the use of new coatings (micro or nano TiO 2 ) and different pulp types could bring savings in wood, energy, GHG emissions and other environmental impacts in comparison with conventional printing and writing paper. We studied three types of pulp, namely i) unbleached virgin kraft pulp, ii) recovered fiber, and iii) high yield virgin chemithermo-mechanical pulp (CTMP). A life cycle assessment (LCA) was conducted from cradle to grave. Applying attributional modeling, we found that wood savings amount to 60% for the nanoparticle coated recovered fiber paper and 35% for the micro TiO 2 coated CTMP paper. According to the ReCiPe single score impact assessment method, the new product configurations allow the reduction of the environmental impacts by 10–35% compared to conventional kraft paper. Applying consequential modeling, we found larger energy and GHG emission savings compared to attributional modeling because the saved wood is used for producing energy, thereby replacing fossil fuels. The nanoparticle coated recovered fiber paper offered savings of non-renewable energy use (NREU) by 100% (13 GJ/ton paper) and GHG emission reduction by 75% (0.6 ton CO 2 eq./ton paper). Micro TiO 2 coated CTMP paper offered NREU savings by 25% (3 GJ/ton paper) and savings of GHG emissions by 10% (0.1 ton CO 2 eq./ton paper). The taking into account of all environmental impacts with the ReCiPe single score method leads to comparable results as that of attributional modeling. We conclude that the nanoparticle coated recovered fiber paper offered the highest savings and lowest environmental impacts. However, human toxicity and ecotoxicity impacts of the nanoparticles were not included in this analysis and need further research. If this leads to the conclusion that the toxicity impacts of the nanoparticles are serious, then

  7. High-pressure homogenization of raw and pasteurized milk modifies the yield, composition, and texture of queso fresco cheese.

    Science.gov (United States)

    Escobar, D; Clark, S; Ganesan, V; Repiso, L; Waller, J; Harte, F

    2011-03-01

    High-pressure homogenization (HPH) of milk was studied as an alternative processing operation in the manufacturing of queso fresco cheese. Raw and pasteurized (65°C for 30 min) milks were subjected to HPH at 0, 100, 200, and 300 MPa and then used to manufacture queso fresco. The cheeses were evaluated for yield, moisture content, titratable acidity, nitrogen content, whey protein content, yield force, yield strain, and tactile texture by instrumental or trained panel analyses. The combination of HPH and thermal processing of milk resulted in cheeses with increased yield and moisture content. The net amount of protein transferred to the cheese per kilogram of milk remained constant for all treatments except raw milk processed at 300 MPa. The highest cheese yield, moisture content, and crumbliness were obtained for thermally processed milk subjected to HPH at 300 MPa. The principal component analysis of all measured variables showed that the variables yield, moisture content, and crumbliness were strongly correlated to each other and negatively correlated to the variables yield strain, protein content (wet basis), and sensory cohesiveness. It is suggested that the combination of thermal processing and HPH promotes thermally induced denaturation of whey protein, together with homogenization-induced dissociation of casein micelles. The combined effect results in queso fresco containing a thin casein-whey matrix that is able to better retain sweet whey. These results indicate that HPH has a strong potential for the manufacture of queso fresco with excellent yield and textural properties. Copyright © 2011 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

  8. Effects of Plant Density on Sweet and Baby Corn (Hybrid KSC 403 Yield and Yield Components

    Directory of Open Access Journals (Sweden)

    H Bavi

    2016-07-01

    Full Text Available Introduction Sweet corn is the one of the most important types of corn. There is a high amount of sugar in the endosperm of sweet corn than dent corn. Baby corn is the ear of corn that is being harvested in the silking stage before the end of pollination. This crop has an interesting using methods as salad, conserve production and vegetative consumption. Both two sweet and baby corn is obtained from one plant in different growth stages and could be harvested from one corn hybrid. Best yield and quality of baby corn is obtained from sweet corn hybrids, because of high amounts of sugar in the grains and ears. Sweet corn and baby corn could be harvested at early dough stage (with about 30 % of humidity and early silking stage before the pollination is completed, respectively. Plant density is the most important factor in growing corn, especially in sweet and baby corn. Khuzestan province is one of the main regions of corn production in Iran. In Khuzestan, forage and silage corn have the most production among the summer crops. Corn is planted in two planting date in Khuzestan: early spring and early summer. Spring corn planting produces little grain yield due to Simultaneity of silking stage with hot early summer days. Because of little production and little research about sweet and baby corn, this study was performed and designed. Materials and Methods In order to investigate the effects of plant density and harvesting method on sweet corn and baby corn yield, an experiment was performed during 2012-13, in research farm of Ramin Agriculture and Natural Resources University of Khuzestan, located in southwest of Iran. In this experiment, four plant densities (7, 9, 11 and 13 plants.m-2 and two harvesting methods (baby corn and sweet corn were investigated in an RCB statistical design with four replications. The KSC 403 hybrid was used and investigated in the experiment, as a sweet corn hybrid. Statistical analysis was performed using SAS 9.1 through

  9. Development of a New Class of Scintillating Fibres with Very Short Decay Time and High Light Yield

    International Nuclear Information System (INIS)

    Borshchev, O.; Ponomarenko, S.; Surin, N.; Cavalcante, A.B.R.; Gavardi, L.; Gruber, L.; Joram, C.; Shinji, O.

    2017-01-01

    We present first studies of a new class of scintillating fibres which are characterised by very short decay times and high light yield. The fibres are based on a novel type of luminophores admixed to a polystyrene core matrix. These so-called Nanostructured Organosilicon Luminophores (NOL) have high photoluminescense quantum yield and decay times just above 1 ns. A blue and a green emitting prototype fibre with 250 μm diameter were produced and characterised in terms of attenuation length, ionisation light yield, decay time and tolerance to x-ray irradiation. The well-established Kuraray SCSF-78 and SCSF-3HF fibres were taken as references. Even though the two prototype fibres mark just an intermediate step in an ongoing development, their performance is already on a competitive level. In particular, their decay time constants are about a factor of two shorter than the fastest known fibres, which makes them promising candidates for time critical applications.

  10. High-yield production of pure tagatose from fructose by a three-step enzymatic cascade reaction.

    Science.gov (United States)

    Lee, Seon-Hwa; Hong, Seung-Hye; Kim, Kyoung-Rok; Oh, Deok-Kun

    2017-08-01

    To produce tagatose from fructose with a high conversion rate and to establish a high-yield purification method of tagatose from the reaction mixture. Fructose at 1 M (180 g l -1 ) was converted to 0.8 M (144 g l -1 ) tagatose by a three-step enzymatic cascade reaction, involving hexokinase, plus ATP, fructose-1,6-biphosphate aldolase, phytase, over 16 h with a productivity of 9 g l -1 h -1 . No byproducts were detected. Tagatose was recrystallized from ethanol to a purity of 99.9% and a yield of 96.3%. Overall, tagatose at 99.9% purity was obtained from fructose with a yield of 77%. This is the first biotechnological production of tagatose from fructose and the first application of solvent recrystallization for the purification of rare sugars.

  11. High-yield exfoliation of tungsten disulphide nanosheets by rational mixing of low-boiling-point solvents

    Science.gov (United States)

    Sajedi-Moghaddam, Ali; Saievar-Iranizad, Esmaiel

    2018-01-01

    Developing high-throughput, reliable, and facile approaches for producing atomically thin sheets of transition metal dichalcogenides is of great importance to pave the way for their use in real applications. Here, we report a highly promising route for exfoliating two-dimensional tungsten disulphide sheets by using binary combination of low-boiling-point solvents. Experimental results show significant dependence of exfoliation yield on the type of solvents as well as relative volume fraction of each solvent. The highest yield was found for appropriate combination of isopropanol/water (20 vol% isopropanol and 80 vol% water) which is approximately 7 times higher than that in pure isopropanol and 4 times higher than that in pure water. The dramatic increase in exfoliation yield can be attributed to perfect match between the surface tension of tungsten disulphide and binary solvent system. Furthermore, solvent molecular size also has a profound impact on the exfoliation efficiency, due to the steric repulsion.

  12. Effect of coloured polyethylene mulch and harvesting stage on ...

    African Journals Online (AJOL)

    Coloured polyethylene significantly (P < 0.05) increased the stalk length, stalk girth, number of tillers, chewable stalk and yield of NCS 008 for the main, as well as, the ratoon crops. Harvesting stage significantly influenced the stalk length, stalk girth and yield. Plots harvested 12 months after planting performed better than ...

  13. High-yield secretion of recombinant proteins from the microalga Chlamydomonas reinhardtii.

    Science.gov (United States)

    Ramos-Martinez, Erick Miguel; Fimognari, Lorenzo; Sakuragi, Yumiko

    2017-09-01

    Microalga-based biomanufacturing of recombinant proteins is attracting growing attention due to its advantages in safety, metabolic diversity, scalability and sustainability. Secretion of recombinant proteins can accelerate the use of microalgal platforms by allowing post-translational modifications and easy recovery of products from the culture media. However, currently, the yields of secreted recombinant proteins are low, which hampers the commercial application of this strategy. This study aimed at expanding the genetic tools for enhancing secretion of recombinant proteins in Chlamydomonas reinhardtii, a widely used green microalga as a model organism and a potential industrial biotechnology platform. We demonstrated that the putative signal sequence from C. reinhardtii gametolysin can assist the secretion of the yellow fluorescent protein Venus into the culture media. To increase the secretion yields, Venus was C-terminally fused with synthetic glycomodules comprised of tandem serine (Ser) and proline (Pro) repeats of 10 and 20 units [hereafter (SP) n , wherein n = 10 or 20]. The yields of the (SP) n -fused Venus were higher than Venus without the glycomodule by up to 12-fold, with the maximum yield of 15 mg/L. Moreover, the presence of the glycomodules conferred an enhanced proteolytic protein stability. The Venus-(SP) n proteins were shown to be glycosylated, and a treatment of the cells with brefeldin A led to a suggestion that glycosylation of the (SP) n glycomodules starts in the endoplasmic reticulum (ER). Taken together, the results demonstrate the utility of the gametolysin signal sequence and (SP) n glycomodule to promote a more efficient biomanufacturing of microalgae-based recombinant proteins. © 2017 The Authors. Plant Biotechnology Journal published by Society for Experimental Biology and The Association of Applied Biologists and John Wiley & Sons Ltd.

  14. High-yielding Wheat Varieties Harbour Superior Plant Growth Promoting-Bacterial Endophytes

    Directory of Open Access Journals (Sweden)

    Mehwish Yousaf

    2017-06-01

    Full Text Available Background and Objective: The purpose of this study was to compare the endophytic microbial flora of different wheat varieties to check whether a better yielding variety also harbours superior plant growth promoting bacteria. Such bacteria are helpful in food biotechnology as their application can enhance the yield of the crop.Material and Methods: Three wheat varieties (Seher, Faisalabad and Lasani were selected, Seher being the most superior variety. endophytic bacteria were isolated from the histosphere of the leaves and roots at different growth phases of the plants. The isolates were analyzed for plant growth promoting activities. Isolates giving best results were identified through 16S rRNA gene sequencing. Statistical analysis was done using Microsoft Excel 2013. All the experiments were conducted in triplicates.Results and Conclusion: The endophytes of Seher variety showed maximum plant growth promoting abilities. Among the shoot endophytes, the highest auxin production was shown by Seher isolate SHHP1-3 up to 51.9μg ml-1, whereas in the case of root endophytes, the highest auxin was produced by SHHR1-5 up to 36 μg ml-1. The bacteria showing significant plant growth promoting abilities were identified by 16S rRNA sequencing. Bacillus, Proteobacteria and Actinobacteria species were the dominant bacteria showing all the traits of plant growth promotion. It can be concluded that Seher variety harbours superior plant growth promoting endophytes that must be one of the reasons for its better growth and yield as compared to the other two varieties. The investigated results support possible utilization of the selected isolates in wheat growth promotion with respect to increase in agro-productivity. The application of such bacteria could be useful to enhance wheat yield and can help in food biotechnology.Conflict of interest: The authors declare no conflict of interest.

  15. High quantum yield ZnO quantum dots synthesizing via an ultrasonication microreactor method.

    Science.gov (United States)

    Yang, Weimin; Yang, Huafang; Ding, Wenhao; Zhang, Bing; Zhang, Le; Wang, Lixi; Yu, Mingxun; Zhang, Qitu

    2016-11-01

    Green emission ZnO quantum dots were synthesized by an ultrasonic microreactor. Ultrasonic radiation brought bubbles through ultrasonic cavitation. These bubbles built microreactor inside the microreactor. The photoluminescence properties of ZnO quantum dots synthesized with different flow rate, ultrasonic power and temperature were discussed. Flow rate, ultrasonic power and temperature would influence the type and quantity of defects in ZnO quantum dots. The sizes of ZnO quantum dots would be controlled by those conditions as well. Flow rate affected the reaction time. With the increasing of flow rate, the sizes of ZnO quantum dots decreased and the quantum yields first increased then decreased. Ultrasonic power changed the ultrasonic cavitation intensity, which affected the reaction energy and the separation of the solution. With the increasing of ultrasonic power, sizes of ZnO quantum dots first decreased then increased, while the quantum yields kept increasing. The effect of ultrasonic temperature on the photoluminescence properties of ZnO quantum dots was influenced by the flow rate. Different flow rate related to opposite changing trend. Moreover, the quantum yields of ZnO QDs synthesized by ultrasonic microreactor could reach 64.7%, which is higher than those synthesized only under ultrasonic radiation or only by microreactor. Copyright © 2016 Elsevier B.V. All rights reserved.

  16. Development of a High-performance Fluorpolymer Electret Mixed with Nano-particles and Its Application to Vibration Energy Harvesting

    International Nuclear Information System (INIS)

    Suzuki, M; Takahashi, T; Aoyagi, S

    2014-01-01

    We have been developing small power generation device of capacitance-type to be converted to electrical energy vibration energy using an electret. In this Study, dielectric nanoparticles were mixed with an electret made of fluorocarbon polymer. As a result, implanted charge density of the electret was successfully enhanced thanks to the mixing of particles. A small sized vibration energy harvester (VEH) was fabricated using the fluorocarbon mixed with dielectric nano-particles. As a result of applying vibration (20 Hz, 0.65 G) to the fabricated VEH, The maximum generated power of approximately 50 μW was obtained

  17. Effects of Biomass Feedstock on the Yield and Reactivity of Soot from Fast Pyrolysis at High Temperatures

    DEFF Research Database (Denmark)

    Trubetskaya, Anna; Jensen, Peter A.; Glarborg, Peter

    This study investigated the effect of feedstock on the yield, nanostructure and reactivity of soot. Woody and herbaceous biomass were pyrolyzed at high heating rates and temperatures of 1250 and 1400°C in a drop tube furnace. The collected solid residues were structurally characterized by electro...

  18. REGIONAL ANALYSIS OF INORGANIC NITROGEN YIELD AND RETENTION IN HIGH-ELEVATION ECOSYSTEMS OF THE SIERRA NEVADA AND ROCKY MOUNTAINS

    Science.gov (United States)

    Yields and retention of inorganic nitrogen (DIN) and nitrate concentrations in surface runoff are summarized for 28 high elevation watersheds in the Sierra Nevada, California and Rocky Mountains of Wyoming and Colorado. Catchments ranged in elevation from 2475 to 3603 m and from...

  19. Hydroxyl radical yields in the tracks of high energy 13C6+ and 36Ar18+ ions in liquid water

    International Nuclear Information System (INIS)

    Baldacchino, G.; Vigneron, G.; Renault, J.P.; Le Caer, S.; Pin, S.; Mialocq, J.-C.; Balanzat, E.; Bouffard, S.

    2006-01-01

    This article reports the determination of the OH · radiolytic yields in water irradiated by high energy C 6+ and Ar 18+ ions with LET values of 32 ± 2 and 280 ± 10 eV nm -1 . The time evolution of the yields between 9 x 10 -11 and 9 x 10 -8 s was deduced using the scavenging method with SCN - and Br - and pulse radiolysis with pulses of 5 and 10 μs. The thiocyanate chemical system is less affected with the local high dose rates specific to the high LET particles than the bromide system. At 32 eV nm -1 with C 6+ ions, G(OH · ) reaches a maximum of 1.5 x 10 -7 mol J -1 at 1 ns and decreases at earlier times. With Ar 18+ ions of 280 eV nm -1 G(OH · ) is always increasing at early times up to 1.6 x 10 -7 mol J -1 at 9 x 10 -11 s. In this case the evolution of the hydroxyl radical yields agrees with the high local concentrations obtained with Ar 18+ and C 6+ ions and depicted in recent literature with the yields of the hydrated electron in the ns range

  20. Exogenously applied plant growth regulators enhance the morpho-physiological growth and yield of rice under high temperature

    Directory of Open Access Journals (Sweden)

    Shah Fahad

    2016-08-01

    Full Text Available A two-year experiment was conducted to ascertain the effects of exogenously applied plant growth regulators (PGR on rice growth and yield attributes under high day (HDT and high night temperature (HNT. Two rice cultivars (IR-64 and Huanghuazhan were subjected to temperature treatments in controlled growth chambers and four different combinations of ascorbic acid (Vc, alpha-tocopherol (Ve, brassinosteroids (Br, methyl jasmonates (MeJA and triazoles (Tr were applied. High temperature severely affected rice morphology, and also reduced leaf area, above- and below-ground biomass, photosynthesis, and water use efficiency, while increased the leaf water potential of both rice cultivars. Grain yield and its related attributes except number of panicles, were reduced under high temperature. The HDT posed more negative effects on rice physiological attributes, while HNT was more detrimental for grain formation and yield. The Huanghuazhan performed better than IR-64 under high temperature stress with better growth and higher grain yield. Exogenous application of PGRs was helpful in alleviating the adverse effects of high temperature. Among PGR combinations, the Vc+Ve+MejA+Br was the most effective treatment for both cultivars under high temperature stress. The highest grain production by Vc+Ve+MejA+Br treated plants was due to enhanced photosynthesis, spikelet fertility and grain filling, which compensated the adversities of high temperature stress. Taken together, these results will be of worth for further understanding the adaptation and survival mechanisms of rice to high temperature and will assist in developing heat-resistant rice germplasm in future.

  1. Demonstration of radiation pulse shaping with nested-tungsten-wire-array pinches for high-yield inertial confinement fusion.

    Science.gov (United States)

    Cuneo, M E; Vesey, R A; Sinars, D B; Chittenden, J P; Waisman, E M; Lemke, R W; Lebedev, S V; Bliss, D E; Stygar, W A; Porter, J L; Schroen, D G; Mazarakis, M G; Chandler, G A; Mehlhorn, T A

    2005-10-28

    Nested wire-array pinches are shown to generate soft x-ray radiation pulse shapes required for three-shock isentropic compression and hot-spot ignition of high-yield inertial confinement fusion capsules. We demonstrate a reproducible and tunable foot pulse (first shock) produced by interaction of the outer and inner arrays. A first-step pulse (second shock) is produced by inner array collision with a central CH2 foam target. Stagnation of the inner array at the axis produces the third shock. Capsules optimized for several of these shapes produce 290-900 MJ fusion yields in 1D simulations.

  2. Productivity, Profitability and Resource Use Efficiency: A Comparative Analysis between Conventional and High Yielding Rice in Rajbari District, Bangladesh

    Directory of Open Access Journals (Sweden)

    Md. Yahia Bapari

    2016-10-01

    Full Text Available The study was analyzed the determinants, costs and benefits and resources allocation of both conventional and high yielding rice cultivation over the Rajbari district of Bangladesh. Data were accumulated from 300 regular rice growers of conventional and high yielding varieties and random sampling technique was applied for selecting the respondents from the study area from which information was collected through pre-tested questionnaire. Cobb – Douglas production function and gross margin were mainly used to determine the productivities and profits of both rice and the marginal value of the product was highly recommended to derive the optimal use of the resources. Results obtained by applying ordinary least square method showed that the most important factors of production in the study area were irrigation, labor, fertilizer and insecticide costs whose elasticities were 0.904, 0.048, 0.045 and 0.044 respectively and insignificant factors were seed and ploughing costs whose elasticities were – 0.009 and 0.030 respectively for high yielding rice. On the other hand, irrigation, insecticide, seed and ploughing costs of elasticities 0.880, 0.589, 0.116 and – 0.127 respectively were the important factors and minor role playing factors were labor and fertilizer costs whose elasticities were 0.098 and 0.077 respectively for conventional yielding rice. The core message from productivity analysis was that the irrigation was key variable which played a positive and vital role in producing rice of both varieties. All variables (resources were economically misallocated in the production activities of both varieties along the study area but high yielding rice was more profitable than conventional one. Results also showed that the farmers of the study area produced rice of both varieties in the inefficient range of production. Continuous supply of electricity, flexible credit and improving the existing resources were the prime policy recommendations of

  3. Effects of Water Management, Arsenic and Phosphorus Levels on Rice Yield in High-Arsenic Soil-Water System

    Institute of Scientific and Technical Information of China (English)

    A. S. M. H. M. TALUKDER; C. A. MEISNER; M. A. R. SARKAR; M. S. ISLAM; K. D. SAYRE

    2014-01-01

    Aerobic rice (Oryza sativa L.) cultivation is considered an alternative production system to combat increased water scarcity and arsenic (As) contamination in the food chain. Pot experiments were conducted at the Wheat Research Centre, Dinajpur, Bangladesh to examine the role of water management (WM), As and phosphorus (P) on yield and yield attributes of boro (variety BRRI dhan 29) and aman (variety BRRI dhan 32) rice. A total of 18 treatment combinations of the three levels of As (0, 20 and 40 mg/kg) and P (0, 12.5 and 25.0 mg/kg) and two WM strategies (aerobic and anaerobic) were investigated. Yield attributes were significantly affected by increasing As levels. Grain yields of BRRI dhan 29 and BRRI dhan 32 were reduced from 63.0 to 7.7 and 35.0 to 16.5 g/pot with increasing As application, respectively, indicating a greater sensitivity of BRRI dhan 29 than BRRI dhan 32. Moreover, As toxicity was reduced with aerobic compared to anaerobic WM for all P levels. During early growth stages, phytotoxic symptoms appeared on BRRI dhan 29 and BRRI dhan 32 rice stems with increasing As levels without applying P under anaerobic WM. Under anaerobic and As-contaminated conditions, BRRI dhan 29 was highly susceptible to straighthead, which dramatically reduced grain yields. There were significant relationships between the number of effective tillers per pot and root dry weight, grain yield, and number of fertile and unfertile grains per pot for both BRRI dhan 29 and BRRI dhan 32 (P<0.001). Our findings indicate that rice could be grown aerobically in As-contaminated areas with a reduced risk of As toxicity and yield loss.

  4. Studies on the apple trees grafted on high-position for cold-resistance and high yield by using radioactive isotope

    International Nuclear Information System (INIS)

    Yuan Zengyu

    1985-01-01

    The effect of high-position grafting of apple trees on cold-resistance and high yield was significant. The yields of varieties 'Huantaiping' etc. grafted on high posotion after 7 years were increased by up to 100 kg per plant in comparing with that grafted on low position. The photosynthetic products synthesized by high grafting trees and 32 P absorbed by roots were studied by measuring the radioactivity of 32 P and 14 C, and by autoradiograph. The distribution of nutrient in various organs was affected by graft union, and the accumulation of photosynthetic produts in fruit bearing portions was in favour of the differentiation of flowers and the formation of fruits

  5. Multitrait, Random Regression, or Simple Repeatability Model in High-Throughput Phenotyping Data Improve Genomic Prediction for Wheat Grain Yield.

    Science.gov (United States)

    Sun, Jin; Rutkoski, Jessica E; Poland, Jesse A; Crossa, José; Jannink, Jean-Luc; Sorrells, Mark E

    2017-07-01

    High-throughput phenotyping (HTP) platforms can be used to measure traits that are genetically correlated with wheat ( L.) grain yield across time. Incorporating such secondary traits in the multivariate pedigree and genomic prediction models would be desirable to improve indirect selection for grain yield. In this study, we evaluated three statistical models, simple repeatability (SR), multitrait (MT), and random regression (RR), for the longitudinal data of secondary traits and compared the impact of the proposed models for secondary traits on their predictive abilities for grain yield. Grain yield and secondary traits, canopy temperature (CT) and normalized difference vegetation index (NDVI), were collected in five diverse environments for 557 wheat lines with available pedigree and genomic information. A two-stage analysis was applied for pedigree and genomic selection (GS). First, secondary traits were fitted by SR, MT, or RR models, separately, within each environment. Then, best linear unbiased predictions (BLUPs) of secondary traits from the above models were used in the multivariate prediction models to compare predictive abilities for grain yield. Predictive ability was substantially improved by 70%, on average, from multivariate pedigree and genomic models when including secondary traits in both training and test populations. Additionally, (i) predictive abilities slightly varied for MT, RR, or SR models in this data set, (ii) results indicated that including BLUPs of secondary traits from the MT model was the best in severe drought, and (iii) the RR model was slightly better than SR and MT models under drought environment. Copyright © 2017 Crop Science Society of America.

  6. Vineyard Yield Estimation Based on the Analysis of High Resolution Images Obtained with Artificial Illumination at Night

    Directory of Open Access Journals (Sweden)

    Davinia F