Sample records for hap emissions factor
-
2010-07-01
... Halogen HAP Emissions or HAP Metals Emissions From Process Vents 3 Table 3 to Subpart FFFF of Part 63... to Subpart FFFF of Part 63—Emission Limits for Hydrogen Halide and Halogen HAP Emissions or HAP... following table that applies to your process vents that contain hydrogen halide and halogen HAP emissions or...
-
Hazardous air pollutant (HAP) emission characterization of sewage treatment facilities in Korea.
Kang, Kyoung-Hee; Dong, Jong-In
2010-04-01
Until recently, nearly all sewage treatment-related regulations and researches have focused on the removal of the conventional and toxic pollutants from liquid effluents. The discharge of toxic compounds to the atmosphere has been implicitly regarded as a way of removal or destruction. During sewage treatment, the fate mechanism of volatilization/stripping, sorption and biotransformation primarily determines the fate of volatile HAPs. The objectives of this study are to investigate the emission characteristics of HAPs, which are generated from the liquid surface of sewage treatment facilities, by using an emission isolation flux chamber. HAP emissions increased at the inlet of the aerobic chamber during summer due to the relatively high atmospheric temperature. The percent ratio of flux for toluene reached its peak in winter, accounting for 33.6-34.2% of the total, but decreased to 25.1-28.6% in summer. In autumn, trichloroethene (TCE) was the highest, recording 17.6-18.1%, with chloroform and toluene showing similar levels. It seems that the ratio of chlorinated hydrocarbons increases in both summer and autumn because the chamber temperature during that time is higher than winter. This study is the initial study to investigate the emission characteristics of volatile HAPs emitted from domestic sewage treatment facilities to the air in Korea. Therefore, the isolation flux chamber will be used as an emission estimations tool to measure HAPs from sewage treatment facilities and may be applied to develop the emission factor and national source inventory of HAPs.
-
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Leather Finishing HAP Emission Limits for Determining the Allowable HAP Loss 2 Table 2 to Subpart TTTT of Part 63 Protection of Environment... Finishing HAP Emission Limits for Determining the Allowable HAP Loss As required in § 63.5450, you must meet...
-
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Leather Finishing HAP Emission Limits for Determining the Allowable HAP Loss 1 Table 1 to Subpart TTTT of Part 63 Protection of Environment... Finishing HAP Emission Limits for Determining the Allowable HAP Loss As required in §§ 63.5305 and 63.5340(b...
-
40 CFR Table 1 to Subpart Nnnnnn... - HAP Emissions Sources
2010-07-01
... 40 Protection of Environment 14 2010-07-01 2010-07-01 false HAP Emissions Sources 1 Table 1 to Subpart NNNNNN of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR...: Chromium Compounds Pt. 63, Subpt. NNNNNN, Table 1 Table 1 to Subpart NNNNNN of Part 63—HAP Emissions...
-
Assessment of HAPs emissions from advanced power systems
International Nuclear Information System (INIS)
Erickson, T.A.; Brekke, D.W.
1996-01-01
The 1990 Clean Air Act Amendments (CAAA) identified 189 substances as air toxics or hazardous air pollutants (HAPs). Under the CAAA, the U. S. Environmental Protection Agency (EPA) must regulate emissions of these HAPs at their sources, including advanced power systems used for the production of electricity. Eleven trace elements are included in the CAAA list of HAPS, as shown in Table 1. The EPA will define those sources that require regulation and limit their emissions according to regulatory directives. This project focused on evaluating and manipulating the advanced power systems HAPs data currently available for presentation to the U.S. Department of Energy (DOE). Trace components included in the 189 HAPs of the 1990 CAAA are: antimony compounds; arsenic compounds; beryllium compounds; cadmium compounds; chromium compounds; cobalt compounds; lead compounds; manganese compounds; mercury compounds; nickel compounds; and selenium compounds. The review of trace element emissions from advanced power systems and hot-gas cleanup systems included data from Tidd Station, General Electric hot-gas cleanup, Louisiana Gasification Technology Incorporated, and the Cool Water plant. Very few other sources of information were located, and those that were contained significantly flawed information that was not of value to this project. To offset the shortage of information, thermochemical equilibrium predictions were used in evaluating advanced control systems. An outline of the systems reviewed is given in Table 2. In addition to the four demonstration and 1 full-scale systems reviewed, nine conventional systems were also reviewed for comparison with the advanced systems
-
Present and future emissions of HAPs from crematories in China
Xue, Yifeng; Tian, Hezhong; Yan, Jing; Xiong, Chengcheng; Pan, Tao; Nie, Lei; Wu, Xiaoqing; Li, Jing; Wang, Wei; Gao, Jiajia; Zhu, Chuanyong; Wang, Kun
2016-01-01
China is the most populous country in the world. The amount of death population has reached 9.65 million and 49.5% of human corpses are cremated by about 1700 crematories spread throughout the country in 2012, leading to considerable discharge of various hazardous air pollutants (HAPs) into the atmosphere and great concerns on regional air quality and health risks for surrounding residents. By using the practicable or best available emission factors, for the first time, a multiple-year emission inventory of typical hazardous air pollutants discharged from crematories in the Chinese mainland, has been established for the historical period of 1990-2012, and the future trends of HAPs emissions until 2030 are forecasted based on three scenarios analysis. Our results show that the total emissions have gradually increased to 906 t of NOX, 443 t of SO2, 2713 t of CO, 477.7 t of PM, 377 t of HCl, 36 t of H2S, 25 t of NH3, 62 t of NMVOCs, 592 kg of Hg, 48 kg of Pb, 14 kg of Cd, 53 kg of As, 40 kg of Cr, 37 kg of Cu, 51 kg of Ni, and 96 g of PCDD/Fs as TEQ (toxic equivalent quantity) by the year 2012. Under the business-as-usual (BAU) scenario, various HAPs emitted from cremators would continuously increase with an average growth rate of 3% till to 2030; whereas the emissions will peak at around 2015 and then decline gradually with varied speed under the two improved control scenarios. To mitigate the associated air pollution and health risks caused by crematories, it is of great necessary for implementing more strict emission standards, applying combustion optimization and requiring installation of best available flue gas purification system, as well as powerful supervision for sound operation of crematories.
-
40 CFR 63.1565 - What are my requirements for organic HAP emissions from catalytic cracking units?
2010-07-01
... HAP emissions from catalytic cracking units? 63.1565 Section 63.1565 Protection of Environment... are my requirements for organic HAP emissions from catalytic cracking units? (a) What emission... according to the procedures in the plan. (4) The emission limitations and operating limits for organic HAP...
-
2010-07-01
... polyurethane foam production-HAP emissions from equipment cleaning. 63.1298 Section 63.1298 Protection of... foam production—HAP emissions from equipment cleaning. Each owner or operator of a new or existing...(a)(1) shall not use a HAP or a HAP-based material as an equipment cleaner. ...
-
40 CFR 63.1564 - What are my requirements for metal HAP emissions from catalytic cracking units?
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true What are my requirements for metal HAP... requirements for metal HAP emissions from catalytic cracking units? (a) What emission limitations and work... and operating limits for metal HAP emissions from catalytic cracking units required in paragraphs (a...
-
2010-07-01
... polyurethane foam production-HAP ABA emissions from the production line. 63.1297 Section 63.1297 Protection of... foam production—HAP ABA emissions from the production line. (a) Each owner or operator of a new or... § 63.1293(a)(1) shall control HAP ABA emissions from the slabstock polyurethane foam production line in...
-
40 CFR Table 8 to Subpart Wwww of... - Initial Compliance With Organic HAP Emissions Limits
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Initial Compliance With Organic HAP... Organic HAP Emissions Limits As specified in § 63.5860(a), you must demonstrate initial compliance with organic HAP emissions limits as specified in the following table: For . . . That must meet the following...
-
40 CFR 63.1568 - What are my requirements for HAP emissions from sulfur recovery units?
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true What are my requirements for HAP emissions from sulfur recovery units? 63.1568 Section 63.1568 Protection of Environment ENVIRONMENTAL... requirements for HAP emissions from sulfur recovery units? (a) What emission limitations and work practice...
-
40 CFR 63.1569 - What are my requirements for HAP emissions from bypass lines?
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true What are my requirements for HAP emissions from bypass lines? 63.1569 Section 63.1569 Protection of Environment ENVIRONMENTAL PROTECTION... HAP emissions from bypass lines? (a) What work practice standards must I meet? (1) You must meet each...
-
40 CFR 63.1566 - What are my requirements for organic HAP emissions from catalytic reforming units?
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true What are my requirements for organic HAP emissions from catalytic reforming units? 63.1566 Section 63.1566 Protection of Environment... are my requirements for organic HAP emissions from catalytic reforming units? (a) What emission...
-
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true What are my requirements for inorganic HAP emissions from catalytic reforming units? 63.1567 Section 63.1567 Protection of Environment... are my requirements for inorganic HAP emissions from catalytic reforming units? (a) What emission...
-
40 CFR Table 29 to Subpart Uuu of... - HAP Emission Limits for Sulfur Recovery Units
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true HAP Emission Limits for Sulfur Recovery Units 29 Table 29 to Subpart UUU of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... to Subpart UUU of Part 63—HAP Emission Limits for Sulfur Recovery Units As stated in § 63.1568(a)(1...
-
40 CFR Table 22 to Subpart Uuu of... - Inorganic HAP Emission Limits for Catalytic Reforming Units
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Inorganic HAP Emission Limits for Catalytic Reforming Units 22 Table 22 to Subpart UUU of Part 63 Protection of Environment ENVIRONMENTAL..., Table 22 Table 22 to Subpart UUU of Part 63—Inorganic HAP Emission Limits for Catalytic Reforming Units...
-
40 CFR Table 8 to Subpart Uuu of... - Organic HAP Emission Limits for Catalytic Cracking Units
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Organic HAP Emission Limits for Catalytic Cracking Units 8 Table 8 to Subpart UUU of Part 63 Protection of Environment ENVIRONMENTAL..., Table 8 Table 8 to Subpart UUU of Part 63—Organic HAP Emission Limits for Catalytic Cracking Units As...
-
40 CFR Table 15 to Subpart Uuu of... - Organic HAP Emission Limits for Catalytic Reforming Units
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Organic HAP Emission Limits for Catalytic Reforming Units 15 Table 15 to Subpart UUU of Part 63 Protection of Environment ENVIRONMENTAL..., Table 15 Table 15 to Subpart UUU of Part 63—Organic HAP Emission Limits for Catalytic Reforming Units As...
-
40 CFR Table 1 to Subpart Uuu of... - Metal HAP Emission Limits for Catalytic Cracking Units
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Metal HAP Emission Limits for Catalytic Cracking Units 1 Table 1 to Subpart UUU of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION... Table 1 to Subpart UUU of Part 63—Metal HAP Emission Limits for Catalytic Cracking Units As stated in...
-
2010-07-01
... for Hazardous Air Pollutants: Reinforced Plastic Composites Production Testing and Initial Compliance... per year Oc=controlled oven organic HAP emissions, lbs per year R=total usage of neat resin plus, tpy G=total usage of neat gel coat plus, tpy (b) Averaging option. Use Equation 2 of this section to...
-
40 CFR Table 30 to Subpart Uuu of... - Operating Limits for HAP Emissions From Sulfur Recovery Units
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Operating Limits for HAP Emissions From Sulfur Recovery Units 30 Table 30 to Subpart UUU of Part 63 Protection of Environment ENVIRONMENTAL..., Table 30 Table 30 to Subpart UUU of Part 63—Operating Limits for HAP Emissions From Sulfur Recovery...
-
40 CFR Table 36 to Subpart Uuu of... - Work Practice Standards for HAP Emissions From Bypass Lines
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Work Practice Standards for HAP Emissions From Bypass Lines 36 Table 36 to Subpart UUU of Part 63 Protection of Environment ENVIRONMENTAL..., Table 36 Table 36 to Subpart UUU of Part 63—Work Practice Standards for HAP Emissions From Bypass Lines...
-
2010-07-01
... Requirements for Metal HAP Process Vents 4 Table 4 to Subpart VVVVVV of Part 63 Protection of Environment... of Part 63—Emission Limits and Compliance Requirements for Metal HAP Process Vents As required in § 63.11496(f), you must comply with the requirements for metal HAP process vents as shown in the...
-
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Continuous Monitoring Systems for HAP Emissions From Sulfur Recovery Units 31 Table 31 to Subpart UUU of Part 63 Protection of Environment..., Subpt. UUU, Table 31 Table 31 to Subpart UUU of Part 63—Continuous Monitoring Systems for HAP Emissions...
-
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Continuous Compliance With HAP Emission Limits for Sulfur Recovery Units 34 Table 34 to Subpart UUU of Part 63 Protection of Environment..., Subpt. UUU, Table 34 Table 34 to Subpart UUU of Part 63—Continuous Compliance With HAP Emission Limits...
-
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Initial Compliance With HAP Emission Limits for Sulfur Recovery Units 33 Table 33 to Subpart UUU of Part 63 Protection of Environment..., Subpt. UUU, Table 33 Table 33 to Subpart UUU of Part 63—Initial Compliance With HAP Emission Limits for...
-
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Operating Limits for Organic HAP Emissions From Catalytic Cracking Units 9 Table 9 to Subpart UUU of Part 63 Protection of Environment..., Subpt. UUU, Table 9 Table 9 to Subpart UUU of Part 63—Operating Limits for Organic HAP Emissions From...
-
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Operating Limits for Organic HAP Emissions From Catalytic Reforming Units 16 Table 16 to Subpart UUU of Part 63 Protection of Environment..., Subpt. UUU, Table 16 Table 16 to Subpart UUU of Part 63—Operating Limits for Organic HAP Emissions From...
-
2010-07-01
... HAP Emission Limits for Catalytic Reforming Units 27 Table 27 to Subpart UUU of Part 63 Protection of... Pollutants for Petroleum Refineries: Catalytic Cracking Units, Catalytic Reforming Units, and Sulfur Recovery... Inorganic HAP Emission Limits for Catalytic Reforming Units As stated in § 63.1567(c)(1), you shall meet...
-
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Initial Compliance With Organic HAP Emission Limits for Catalytic Reforming Units 19 Table 19 to Subpart UUU of Part 63 Protection of... HAP Emission Limits for Catalytic Reforming Units As stated in § 63.1566(b)(7), you shall meet each...
-
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Initial Compliance With Organic HAP Emission Limits for Catalytic Cracking Units 12 Table 12 to Subpart UUU of Part 63 Protection of... HAP Emission Limits for Catalytic Cracking Units As stated in § 63.1565(b)(4), you shall meet each...
-
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Continuous Monitoring Systems for Organic HAP Emissions From Catalytic Reforming Units 17 Table 17 to Subpart UUU of Part 63 Protection of... Organic HAP Emissions From Catalytic Reforming Units As stated in § 63.1566(b)(1), you shall meet each...
-
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Continuous Compliance With Organic HAP Emission Limits for Catalytic Cracking Units 13 Table 13 to Subpart UUU of Part 63 Protection of... HAP Emission Limits for Catalytic Cracking Units As stated in § 63.1565(c)(1), you shall meet each...
-
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Continuous Compliance With Organic HAP Emission Limits for Catalytic Reforming Units 20 Table 20 to Subpart UUU of Part 63 Protection of... HAP Emission Limits for Catalytic Reforming Units As stated in § 63.1566(c)(1), you shall meet each...
-
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Continuous Monitoring Systems for Organic HAP Emissions From Catalytic Cracking Units 10 Table 10 to Subpart UUU of Part 63 Protection of... Organic HAP Emissions From Catalytic Cracking Units As stated in § 63.1565(b)(1), you shall meet each...
-
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Continuous Compliance With Metal HAP Emission Limits for Catalytic Cracking Units 6 Table 6 to Subpart UUU of Part 63 Protection of Environment..., Subpt. UUU, Table 6 Table 6 to Subpart UUU of Part 63—Continuous Compliance With Metal HAP Emission...
-
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Initial Compliance With Metal HAP Emission Limits for Catalytic Cracking Units 5 Table 5 to Subpart UUU of Part 63 Protection of Environment..., Subpt. UUU, Table 5 Table 5 to Subpart UUU of Part 63—Initial Compliance With Metal HAP Emission Limits...
-
2010-07-01
.../ton.4 Use the appropriate open molding emission limit.5 9. pultrusion 6 N/A reduce total organic HAP... CATEGORIES National Emissions Standards for Hazardous Air Pollutants: Reinforced Plastic Composites...: If your operation type is . . . And you use . . . 1 Your organic HAP emissions limit is . . . 1. open...
-
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Requirements for Performance Tests for Organic HAP Emissions From Catalytic Reforming Units 18 Table 18 to Subpart UUU of Part 63 Protection of... for Organic HAP Emissions From Catalytic Reforming Units As stated in § 63.1566(b)(2) and (3), you...
-
Estimating HAPs and radionuclide emissions from a laboratory complex at a nuclear processing site
International Nuclear Information System (INIS)
Paul, R.A.; Faugl, T.
1993-01-01
A unique methodology was developed for conducting an air emission inventory (AEI) at a DOE nuclear processing facility. This methodology involved the use of computer-assisted design (CAD) drawings to document emission points, computerized process drawings to document industrial processes leading to emissions, and a computerized data base of AEI forms to document emission estimates and related process data. A detailed air emissions inventory for operating years 1985--1991 was recently implemented for the entire site using this methodology. One industrial area at the DOE Site is comprised of laboratory facilities that provide direct support to the nuclear reactor and recovery operations, developmental studies to support reactor and separation operations, and developmental studies to support waste handling and storage. The majority of the functions are conducted in a single large building complex wherein bench scale and pilot scale experiments are carried out involving radionuclides, hazardous air pollutants (HAP), and other chemicals reportable under the Clean Air Act Amendments (CAAA) and Superfund Amendments and Re-authorization Act (SARA) Title 111. The results of the inventory showed that HAP and radionuclide emissions from the laboratory complex were relatively minor
-
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Continuous Compliance With Operating Limits for Organic HAP Emissions From Catalytic Cracking Units 14 Table 14 to Subpart UUU of Part 63... Compliance With Operating Limits for Organic HAP Emissions From Catalytic Cracking Units As stated in § 63...
-
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Continuous Compliance With Operating Limits for Organic HAP Emissions From Catalytic Reforming Units 21 Table 21 to Subpart UUU of Part 63... Compliance With Operating Limits for Organic HAP Emissions From Catalytic Reforming Units As stated in § 63...
-
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Continuous Compliance With Operating Limits for Metal HAP Emissions From Catalytic Cracking Units 7 Table 7 to Subpart UUU of Part 63... With Operating Limits for Metal HAP Emissions From Catalytic Cracking Units As stated in § 63.1564(c)(1...
-
2010-07-01
... process vents that emit hydrogen halide and halogen HAP or HAP metals? 63.2465 Section 63.2465 Protection... and halogen HAP or HAP metals? (a) You must meet each emission limit in Table 3 to this subpart that... section. (b) If any process vents within a process emit hydrogen halide and halogen HAP, you must...
-
2010-07-01
... Limits for Open Molding, Centrifugal Casting, and SMC Manufacturing Operations Where the Standards Are..., Table 5 Alternative Organic HAP Emissions Limits for Open Molding, Centrifugal Casting, and SMC... casting—CR/HS 3,4 A vent system that moves heated air through the mold 27 lb/ton. 8. Centrifugal casting...
-
Energy Technology Data Exchange (ETDEWEB)
England, G.C.; McGrath, T.P. [GE-Energy and Environmental Research Corp., Irvine, CA (United States); Gilmer, L. [Equilon Enterprises, Bellaire, TX (United States); Seebold, J.G. [Chevron Research and Technology Co., Richmond, CA (United States); Lev-On, M. [ARCO, Los Angeles, CA (United States); Hunt, T. [American Petroleum Institute, Washington, DC (United States)
2001-07-01
Air emissions from gas-fired combustion devices such as boilers, process heaters, gas turbines and stationary reciprocating engines contain hazardous air pollutants (HAPs) subjected to consideration under the federal clean air act (CAA). This work presents a recently completed major research project to develop an understanding of HAP emissions from gas-fired boilers and process heaters and new HAP emission factors based on field emission tests of gas-fired external combustion devices used in the petroleum industry. The effect of combustion system design and operating parameters on HAP emissions determined by both field and research tests are discussed. Data from field tests of gas-fired petroleum industry boilers and heaters generally show very low emission levels of organic HAPs. A comparison of the emission data for boilers and process heaters, including units with and without various forms of NO{sub x} emission controls, showed no significant difference in organic HAP emission characteristics due to process or burner design. This conclusion is also supported by the results of research tests with different burner designs. Based on field tests of units fired with natural gas and various petroleum industry process gases and research tests in which gas composition was intentionally varied, organic HAP emissions were not determined to be significantly affected by the gas composition. Research data indicate that elevated organic HAP emission levels are found only under extreme operating conditions (starved air or high excess air combustion) associated with poor combustion. (author)
-
International Nuclear Information System (INIS)
England, G.C.; McGrath, T.P.; Gilmer, L.; Seebold, J.G.; Lev-On, M.; Hunt, T.
2001-01-01
Air emissions from gas-fired combustion devices such as boilers, process heaters, gas turbines and stationary reciprocating engines contain hazardous air pollutants (HAPs) subjected to consideration under the federal clean air act (CAA). This work presents a recently completed major research project to develop an understanding of HAP emissions from gas-fired boilers and process heaters and new HAP emission factors based on field emission tests of gas-fired external combustion devices used in the petroleum industry. The effect of combustion system design and operating parameters on HAP emissions determined by both field and research tests are discussed. Data from field tests of gas-fired petroleum industry boilers and heaters generally show very low emission levels of organic HAPs. A comparison of the emission data for boilers and process heaters, including units with and without various forms of NO x emission controls, showed no significant difference in organic HAP emission characteristics due to process or burner design. This conclusion is also supported by the results of research tests with different burner designs. Based on field tests of units fired with natural gas and various petroleum industry process gases and research tests in which gas composition was intentionally varied, organic HAP emissions were not determined to be significantly affected by the gas composition. Research data indicate that elevated organic HAP emission levels are found only under extreme operating conditions (starved air or high excess air combustion) associated with poor combustion. (author)
-
2010-07-01
... Emission Limits for Catalytic Reforming Units 26 Table 26 to Subpart UUU of Part 63 Protection of... Pollutants for Petroleum Refineries: Catalytic Cracking Units, Catalytic Reforming Units, and Sulfur Recovery... HAP Emission Limits for Catalytic Reforming Units As stated in § 63.1567(b)(4), you shall meet each...
-
A Gas Chromatographic Continuous Emissions Monitoring System for the Determination of VOCs and HAPs.
Coleman, William M; Gordon, Bert M
1996-01-01
This article describes a new gas chromatography-based emissions monitoring system for measuring volatile organic compounds (VOCs) and hazardous air pollutants (HAPs). The system is composed of a dual-column gas chromatograph equipped with thermal conductivity detectors, in which separation is optimized for fast chromatography. The system has the necessary valving for stream selection, which allows automatic calibration of the system at predetermined times and successive measurement of individual VOCs before and after a control device. Nine different VOCs (two of which are HAPs), plus methane (CH4) and carbon dioxide (CO2) are separated and quantified every two minutes. The accuracy and precision of this system has been demonstrated to be greater than 95%. The system employs a mass flow measurement device and also calculates and displays processed emission data, such as control device efficiency and total weight emitted during given time periods. Two such systems have been operational for one year in two separate gravure printing facilities; minimal upkeep is required, about one hour per month. One of these systems, used before and after a carbon adsorber, has been approved by the pertinent local permitting authority.
-
Xue, Yifeng; Nie, Lei; Zhou, Zhen; Tian, Hezhong; Yan, Jing; Wu, Xiaoqing; Cheng, Linglong
2017-07-01
The consumption of natural gas in Beijing has increased in the past decade due to energy structure adjustments and air pollution abatement. In this study, an integrated emission inventory of hazardous air pollutants (HAPs) emitted from gas-fired combustion in Beijing was developed for the period from 2000 to 2014 using a technology-based approach. Future emission trends were projected through 2030 based on current energy-related and emission control policies. We found that emissions of primary HAPs exhibited an increasing trend with the rapid increase in natural gas consumption. Our estimates indicated that the total emissions of NO X , particulate matter (PM) 10 , PM 2.5 , CO, VOCs, SO 2 , black carbon, Pb, Cd, Hg, As, Cr, Cu, Ni, Zn, polychlorinated dibenzo-p-dioxins and dibenzofurans, and benzo[a]pyrene from gas-fired combustion in Beijing were approximately 22,422 t, 1042 t, 781 t, 19,097 t, 653 t, 82 t, 19 t, 0.6 kg, 0.1 kg, 43 kg, 52 kg, 0.3 kg, 0.03 kg, 4.3 kg, 0.6 kg, 216 μg, and 242 g, respectively, in 2014. To mitigate the associated air pollution and health risks caused by gas-fired combustion, stricter emission standards must be established. Additionally, combustion optimization and flue gas purification system could be used for lowering NO X emissions from gas-fired combustion, and gas-fired facilities should be continuously monitored based on emission limits. Graphical abstract Spatial distribution and typical live photos of gas-fired boiler in Beijing.
-
Biochemical Removal of HAP Precursors From Coal
Energy Technology Data Exchange (ETDEWEB)
Olson, G.; Tucker, L.; Richards, J.
1997-07-01
This project addresses DOE`s interest in advanced concepts for controlling emissions of air toxics from coal-fired utility boilers. We are determining the feasibility of developing a biochemical process for the precombustion removal of substantial percentages of 13 inorganic hazardous air pollutant (HAP) precursors from coal. These HAP precursors are Sb, As, Be, Cd, Cr, Cl, Co, F, Pb, Hg, Mn, Ni, and Se. Although rapid physical coal cleaning is done routinely in preparation plants, biochemical processes for removal of HAP precursors from coal potentially offer advantages of deeper cleaning, more specificity, and less coal loss. Compared to chemical processes for coal cleaning, biochemical processes potentially offer lower costs and milder process conditions. Pyrite oxidizing bacteria, most notably Thiobacillusferrooxidans, are being evaluated in this project for their ability to remove HAP precursors from U.S. coals.
-
Biochemical Removal of HAP Precursors From Coal
International Nuclear Information System (INIS)
Olson, G.; Tucker, L.; Richards, J.
1997-07-01
This project addresses DOE's interest in advanced concepts for controlling emissions of air toxics from coal-fired utility boilers. We are determining the feasibility of developing a biochemical process for the precombustion removal of substantial percentages of 13 inorganic hazardous air pollutant (HAP) precursors from coal. These HAP precursors are Sb, As, Be, Cd, Cr, Cl, Co, F, Pb, Hg, Mn, Ni, and Se. Although rapid physical coal cleaning is done routinely in preparation plants, biochemical processes for removal of HAP precursors from coal potentially offer advantages of deeper cleaning, more specificity, and less coal loss. Compared to chemical processes for coal cleaning, biochemical processes potentially offer lower costs and milder process conditions. Pyrite oxidizing bacteria, most notably Thiobacillusferrooxidans, are being evaluated in this project for their ability to remove HAP precursors from U.S. coals
-
Tackling the problem of fine particulate (HAP) collection
Energy Technology Data Exchange (ETDEWEB)
Parker, K.; Sanyal, A.
2000-07-01
With increasing concern over the emission of hazardous air pollutants (HAPs), measures are being considered to limit their discharge from many industrial sources. The main thrust o the proposed legislation is towards the power generators, because of their potentially large mass emissions, but also at specific targets, such as incinerators. Legislation already exists governing the emission of heavy metals, etc., from various types of incineration process and regulations controlling the emission of pM 2.5 material are proposed for the US. Provided the HAPs are in a solid particulate phase then their collection can be accomplished by correctly designed and operated control systems, such as electrostatic precipitators and bag filters. There are, however, other HAP species which are usually in a gaseous phase at normal back end temperatures, such as elemental mercury, dioxins, furans, etc. These need special consideration and equipment in order to satisfy the proposed regulations. one of the difficulties facing the designers and operators of processes giving rise to these species is the accurate measurement of these trace elements and predicting the uncontrolled emission level in order to size the collection system such as to remain in compliance. The options for the effective collection of these normally gaseous phase pollutants will be examined; these methods will include combined wet and dry collection, absorption and carbon injection systems. Finally, whichever system is finally considered and adopted, in order to satisfy and proposed regulations, will add significant capital and operating cost to the overall installation.
-
Evaluation of model-predicted hazardous air pollutants (HAPs) near a mid-sized U.S. airport
Vennam, Lakshmi Pradeepa; Vizuete, William; Arunachalam, Saravanan
2015-10-01
Accurate modeling of aircraft-emitted pollutants in the vicinity of airports is essential to study the impact on local air quality and to answer policy and health-impact related issues. To quantify air quality impacts of airport-related hazardous air pollutants (HAPs), we carried out a fine-scale (4 × 4 km horizontal resolution) Community Multiscale Air Quality model (CMAQ) model simulation at the T.F. Green airport in Providence (PVD), Rhode Island. We considered temporally and spatially resolved aircraft emissions from the new Aviation Environmental Design Tool (AEDT). These model predictions were then evaluated with observations from a field campaign focused on assessing HAPs near the PVD airport. The annual normalized mean error (NME) was in the range of 36-70% normalized mean error for all HAPs except for acrolein (>70%). The addition of highly resolved aircraft emissions showed only marginally incremental improvements in performance (1-2% decrease in NME) of some HAPs (formaldehyde, xylene). When compared to a coarser 36 × 36 km grid resolution, the 4 × 4 km grid resolution did improve performance by up to 5-20% NME for formaldehyde and acetaldehyde. The change in power setting (from traditional International Civil Aviation Organization (ICAO) 7% to observation studies based 4%) doubled the aircraft idling emissions of HAPs, but led to only a 2% decrease in NME. Overall modeled aircraft-attributable contributions are in the range of 0.5-28% near a mid-sized airport grid-cell with maximum impacts seen only within 4-16 km from the airport grid-cell. Comparison of CMAQ predictions with HAP estimates from EPA's National Air Toxics Assessment (NATA) did show similar annual mean concentrations and equally poor performance. Current estimates of HAPs for PVD are a challenge for modeling systems and refinements in our ability to simulate aircraft emissions have made only incremental improvements. Even with unrealistic increases in HAPs aviation emissions the model
-
2010-07-01
... Refineries: Catalytic Cracking Units, Catalytic Reforming Units, and Sulfur Recovery Units Pt. 63, Subpt. UUU... Organic HAP Emissions From Catalytic Cracking Units Not Subject to New Source Performance Standard (NSPS... From Catalytic Cracking Units Not Subject to New Source Performance Standard (NSPS) for Carbon Monoxide...
-
40 CFR Table 4 to Subpart Ppp of... - Known Organic HAP From Polyether Polyol Products
2010-07-01
... 40 Protection of Environment 11 2010-07-01 2010-07-01 true Known Organic HAP From Polyether Polyol... CATEGORIES National Emission Standards for Hazardous Air Pollutant Emissions for Polyether Polyols Production Pt. 63, Subpt. PPP, Table 4 Table 4 to Subpart PPP of Part 63—Known Organic HAP From Polyether Polyol...
-
2010-07-01
... polyurethane foam production-HAP ABA equipment leaks. 63.1296 Section 63.1296 Protection of Environment... production—HAP ABA equipment leaks. Each owner or operator of a new or existing slabstock affected source complying with the emission point specific limitation option provided in § 63.1293(a) shall control HAP ABA...
-
2010-07-01
... polyurethane foam production-HAP ABA storage vessels. 63.1295 Section 63.1295 Protection of Environment... production—HAP ABA storage vessels. Each owner or operator of a new or existing slabstock affected source complying with the emission point specific limitation option provided in § 63.1293(a) shall control HAP ABA...
-
Kajian Teknologi High Altitude Platform (HAP [Study of High Altitude Platform (HAP Technology
Directory of Open Access Journals (Sweden)
Amry Daulat Gultom
2016-07-01
Full Text Available High Altitude Platform (HAP merupakan solusi alternatif untuk mengatasi keterbatasan infrastruktur terestrial maupun satelit. HAP merupakan pesawat ataupun balon udara yang ditempatkan pada ketinggian 20-50 km di atas permukaan bumi. Kelebihan yang utama dari HAP adalah kemudahan dalam penempatan, fleksibilitas, biaya operasionalnya rendah, delay propagasi rendah, sudut elevasi lebar, cakupan yang luas. Penelitian ini dilakukan untuk mengetahui potensi HAP untuk komunikasi pita lebar dan perkembangannya di Indonesia. Analisis dilakukan secara deskriptif dengan mengolah data literatur yang didapat. Hasil penelitian menunjukkan bahwa di Indonesia terdapat potensi teknologi HAP untuk komunikasi pita lebar dengan lebar pita 2x300 MHz di band 27,9-28,2 GHz dan 31-31,3 GHz. Namun, belum ada peraturan yang mengatur alokasi frekuensi untuk HAP secara khusus di Indonesia.*****High Altitude Platform (HAP has been developed as an alternative solution in order to overcome limitation of terrestrial and satellite communication system. HAP is an aircraft or balloon situated on 20-50 km above the earth. Main advantages of HAP are flexibility in deployment, low propagation delay, wide elevation angle and broad coverage. The research is conducted to gather HAP potential for broadband communication and its development in Indonesia. Analysis is conducted by descriptive analysis from literature study gather. The research result shows that in Indonesia, there is potential of HAP technology for broadband communication with 2x300 MHz bandwidth within 27,9-28,2 GHz and 31-31,3 GHz. Yet, there are no specific regulations managing frequency allocation for HAP in Indonesia.
-
Monitoring by Control Technique - Compliant (Low/No VOC/HAP) Inks and Coatings
Stationary source emissions monitoring is required to demonstrate that a source is meeting the requirements in Federal or state rules. This page is about Compliant (Low/No VOC/HAP) Inks and Coatings control techniques used to reduce pollutant emissions.
-
Das, Ipsita; Pedit, Joseph; Handa, Sudhanshu; Jagger, Pamela
2018-04-01
Exposure to household air pollution (HAP) from cooking and heating with solid fuels is a major risk factor for morbidity and mortality in sub-Saharan Africa. Children under five are particularly at risk for acute lower respiratory infection. We use baseline data from a randomized controlled trial evaluating a household energy intervention in Gisenyi, Rwanda to investigate the role of the microenvironment as a determinant of children’s HAP-related health symptoms. Our sample includes 529 households, with 694 children under five. We examine the association between likelihood of HAP-related health symptom prevalence and characteristics of the microenvironment including: dwelling and cooking area structure; distance to nearest road; and tree cover. We find that children residing in groups of enclosed dwellings, in households that cook indoors, and in households proximate to tree cover, are significantly more likely to experience symptoms of respiratory infection, illness with cough and difficulty breathing. On the other hand, children in households with cemented floors and ventilation holes in the cooking area, are significantly less likely to experience the same symptoms. Our findings suggest that in addition to promoting increased access to clean cooking technologies, there are important infrastructure and microenvironment-related interventions that mitigate HAP exposure.
-
24 CFR 891.560 - HAP contract.
2010-04-01
... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false HAP contract. 891.560 Section 891... Assistance § 891.560 HAP contract. (a) HAP contract. The housing assistance payments contract sets forth.... (b) HAP contract execution. (1) Upon satisfactory completion of the project, the Borrower and HUD...
-
2010-07-01
... volume fraction of HAP in the actual solvent loss? 63.2854 Section 63.2854 Protection of Environment... AIR POLLUTANTS FOR SOURCE CATEGORIES National Emission Standards for Hazardous Air Pollutants: Solvent... average volume fraction of HAP in the actual solvent loss? (a) This section describes the information and...
-
Adhesion Regulating Molecule 1 Mediates HAP40 Overexpression-Induced Mitochondrial Defects
Huang, Zih-Ning; Chung, Her Min; Fang, Su-Chiung; Her, Lu-Shiun
2017-01-01
Striatal neuron death in Huntington's disease is associated with abnormal mitochondrial dynamics and functions. However, the mechanisms for this mitochondrial dysregulation remain elusive. Increased accumulation of Huntingtin-associated protein 40 (HAP40) has been shown to be associated with Huntington's disease. However, the link between increased HAP40 and Huntington's disease remains largely unknown. Here we show that HAP40 overexpression causes mitochondrial dysfunction and reduces cell viability in the immortalized mouse striatal neurons. HAP40-associated mitochondrial dysfunction is associated with reduction of adhesion regulating molecule 1 (ADRM1) protein. Consistently, depletion of ADRM1 by shRNAs impaired mitochondrial functions and increased mitochondrial fragmentation in mouse striatal cells. Moreover, reducing ADRM1 levels enhanced activity of fission factor dynamin-related GTPase protein 1 (Drp1) via increased phosphorylation at serine 616 of Drp1 (Drp1Ser616). Restoring ADRM1 protein levels was able to reduce HAP40-induced ROS levels and mitochondrial fragmentation and improved mitochondrial functions and cell viability. Moreover, reducing Drp1 activity by Drp1 inhibitor, Mdivi-1, ameliorates both HAP40 overexpression- and ADRM1 depletion-induced mitochondrial dysfunction. Taken together, our studies suggest that HAP40-mediated reduction of ADRM1 alters the mitochondrial fission activity and results in mitochondrial fragmentation and mitochondrial dysfunction. PMID:29209146
-
Directory of Open Access Journals (Sweden)
Won Hee Jung
2010-11-01
Full Text Available The fungal pathogen Cryptococcus neoformans is a major cause of illness in immunocompromised individuals such as AIDS patients. The ability of the fungus to acquire nutrients during proliferation in host tissue and the ability to elaborate a polysaccharide capsule are critical determinants of disease outcome. We previously showed that the GATA factor, Cir1, is a major regulator both of the iron uptake functions needed for growth in host tissue and the key virulence factors such as capsule, melanin and growth at 37°C. We are interested in further defining the mechanisms of iron acquisition from inorganic and host-derived iron sources with the goal of understanding the nutritional adaptation of C. neoformans to the host environment. In this study, we investigated the roles of the HAP3 and HAPX genes in iron utilization and virulence. As in other fungi, the C. neoformans Hap proteins negatively influence the expression of genes encoding respiratory and TCA cycle functions under low-iron conditions. However, we also found that HapX plays both positive and negative roles in the regulation of gene expression, including a positive regulatory role in siderophore transporter expression. In addition, HapX also positively regulated the expression of the CIR1 transcript. This situation is in contrast to the negative regulation by HapX of genes encoding GATA iron regulatory factors in Aspergillus nidulans and Schizosaccharomyces pombe. Although both hapX and hap3 mutants were defective in heme utilization in culture, only HapX made a contribution to virulence, and loss of HapX in a strain lacking the high-affinity iron uptake system did not cause further attenuation of disease. Therefore, HapX appears to have a minimal role during infection of mammalian hosts and instead may be an important regulator of environmental iron uptake functions. Overall, these results indicated that C. neoformans employs multiple strategies for iron acquisition during infection.
-
Integrated Satellite-HAP Systems
DEFF Research Database (Denmark)
Cianca, Ernestina; De Sanctis, Mauro; De Luise, Aldo
2005-01-01
Thus far, high-altitude platform (HAP)-based systems have been mainly conceived as an alternative to satellites for complementing the terrestrial network. This article aims to show that HAP should no longer be seen as a competitor technology by investors of satellites, but as a key element for an...
-
24 CFR 891.580 - HAP contract administration.
2010-04-01
... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false HAP contract administration. 891... Handicapped-Section 8 Assistance § 891.580 HAP contract administration. HUD is responsible for the administration of the HAP contract. ...
-
2010-07-01
... (HAP) From the Manufacture of Amino/Phenolic Resins 2 Table 2 to Subpart OOO of Part 63 Protection of... Pollutant Emissions: Manufacture of Amino/Phenolic Resins Pt. 63, Subpt. OOO, Table 2 Table 2 to Subpart OOO of Part 63—Known Organic Hazardous Air Pollutants (HAP) From the Manufacture of Amino/Phenolic Resins...
-
HAPS, a Handy Analog Programming System
DEFF Research Database (Denmark)
Højberg, Kristian Søe
1975-01-01
HAPS (Hybrid Analog Programming System) is an analog compiler that can be run on a minicomputer in an interactive mode. Essentially HAPS is written in FORTRAN. The equations to be programmed for an ana log computer are read in by using a FORTRAN-like notation. The input must contain maximum...... and emphasizes the limitations HAPS puts on equation structure, types of computing circuit, scaling, and static testing....
-
24 CFR 983.202 - Purpose of HAP contract.
2010-04-01
... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Purpose of HAP contract. 983.202... DEVELOPMENT PROJECT-BASED VOUCHER (PBV) PROGRAM Housing Assistance Payments Contract § 983.202 Purpose of HAP contract. (a) Requirement. The PHA must enter into a HAP contract with the owner. The HAP contract must be...
-
24 CFR 891.565 - Term of HAP contract.
2010-04-01
... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Term of HAP contract. 891.565... 8 Assistance § 891.565 Term of HAP contract. The term of the HAP contract for assisted units shall be 20 years. If the project is completed in stages, the term of the HAP contract for assisted units...
-
Characterization of a new sealer MTA/HAp; Caracterizacao de um novo cimento endodontico MTA/HAp
Energy Technology Data Exchange (ETDEWEB)
Barros, C.M.B.; Oliveira, S.V.; Costa, A.C.F.M. [Universidade Federal de Campina Grande (UFCG), PB (Brazil); Dantas, D.C.R.E.; Fontes, L.B.C. [Universidade Estadual da Paraiba (UEPB), PB (Brazil); Viana, K.M.S., E-mail: kalineviana@ect.ufrn.br [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil)
2012-07-01
Filling materials (cement-based calcium hydroxide, amalgam, glass ionomer and IRM) are often used as sealers. However, none of them meets the desirable characteristics of a suitable sealing material. This study aims to characterize the new sealer, MTA/HAp from the incorporation of 5% by weight of synthetic hydroxyapatite to the MTA and to investigate the influence of the addition of HAp on the characteristic structural, chemical and consistency of the MTA. For this, we used MTA Angelus ® and HAp synthesized in the laboratory. We used the ratio by mass 95%MTA/5%HAp, where the hydroxyapatite added the characteristic of the MTA osteoconduction. The tests were performed: XRD, XRF and consistency. The results showed that both the new cement had the same crystalline phases as the same chemical composition of its precursors, yet having suitable consistency (plastic mass) of a sealer as well as the pure MTA. (author)
-
24 CFR 983.203 - HAP contract information.
2010-04-01
... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false HAP contract information. 983.203... DEVELOPMENT PROJECT-BASED VOUCHER (PBV) PROGRAM Housing Assistance Payments Contract § 983.203 HAP contract information. The HAP contract must specify: (a) The total number of contract units by number of bedrooms; (b...
-
DksA-HapR-RpoS axis regulates haemagglutinin protease production in Vibrio cholerae.
Basu, Pallabi; Pal, Ritesh Ranjan; Dasgupta, Shreya; Bhadra, Rupak K
2017-06-01
DksA acts as a co-factor for the intracellular small signalling molecule ppGpp during the stringent response. We recently reported that the expression of the haemagglutinin protease (HAP), which is needed for shedding of the cholera pathogen Vibrio cholerae during the late phase of infection, is significantly downregulated in V. cholerae ∆dksA mutant (∆dksAVc) cells. So far, it has been shown that HAP production by V. cholerae cells is critically regulated by HapR and also by RpoS. Here, we provide evidence that V. cholerae DksA (DksAVc) positively regulates HapR at both the transcriptional and post-transcriptional levels. We show that in ∆dksAVc cells the CsrB/C/D sRNAs, required for the maintenance of intracellular levels of hapR transcripts during the stationary growth, are distinctly downregulated. Moreover, the expression of exponential phase regulatory protein Fis, a known negative regulator of HapR, was found to continue even during the stationary phase in ∆dksAVc cells compared to that of wild-type strain, suggesting another layer of complex regulation of HapR by DksAVc. Extensive reporter construct-based and quantitative reverse-transcriptase PCR (qRT-PCR) analyses supported that RpoS is distinctly downregulated at the post-transcriptional/translational levels in stationary phase-grown ∆dksAVc cells. Since HAP expression through HapR and RpoS is stationary phase-specific in V. cholerae, it appears that DksAVc is also a critical stationary phase regulator for fine tuning of the expression of HAP. Moreover, experimental evidence provided in this study clearly supports that DksAVc is sitting at the top of the hierarchy of regulation of expression of HAP in V. cholerae.
-
HAp physical investigation - the effect of sintering temperature
International Nuclear Information System (INIS)
Mohd Reusmaazran Yusof; Idris Besar; Rusnah Mustaffa; Cik Rohaida Che Hak
2004-01-01
The paper presents the effect of sintering temperature on the physical properties of porous hydroxyapatite (HAp). In this study, the HAp was prepared using polymeric sponge techniques with different binder concentration. The sintering process was carried out in air for temperature ranging from 1200 degree C to 1600 degree C. Different physical properties namely density and porosity were observed at different sintering temperatures. The HAp prepared with higher PVP binder showed a slightly decreased in apparent density with increasing sintering temperature, while those HAp prepared with lower PVP showed a slightly increase in apparent density with increasing sintering temperature. The total porosity was found to be approximately constant in the whole sintering temperature range. However, closed porosity decreases with increasing sintering temperature for HAp prepared by lower binder concentration. On the other hand, the HAp prepared by higher binder concentration HAp showed increasing closed porosity with increasing sintering temperature. Other features such as the influence of sintering temperatures on grain and strut also be presented in this paper. (Author)
-
Intersystem Interference Reduction for Overlaid HAPS-Terrestrial CDMA System
Huang, Jeng-Ji; Wang, Wei-Ting; Li, Mingfu; Shiung, David; Ferng, Huei-Wen
In this letter, we propose that directional antennas, combined with power management, be incorporated to reduce intersystem interference in a shared band overlaid high altitude platform station (HAPS)-terrestrial code division multiple access (CDMA) system. To eliminate the HAPS to terrestrial interference, the HAPS is accessed only via directional antennas under the proposed scheme. By doing so, the uplink power to the HAPS can accordingly be increased, so that the terrestrial to HAPS interference is also effectively suppressed.
-
Diversity Performance Analysis on Multiple HAP Networks
Dong, Feihong; Li, Min; Gong, Xiangwu; Li, Hongjun; Gao, Fengyue
2015-01-01
One of the main design challenges in wireless sensor networks (WSNs) is achieving a high-data-rate transmission for individual sensor devices. The high altitude platform (HAP) is an important communication relay platform for WSNs and next-generation wireless networks. Multiple-input multiple-output (MIMO) techniques provide the diversity and multiplexing gain, which can improve the network performance effectively. In this paper, a virtual MIMO (V-MIMO) model is proposed by networking multiple HAPs with the concept of multiple assets in view (MAV). In a shadowed Rician fading channel, the diversity performance is investigated. The probability density function (PDF) and cumulative distribution function (CDF) of the received signal-to-noise ratio (SNR) are derived. In addition, the average symbol error rate (ASER) with BPSK and QPSK is given for the V-MIMO model. The system capacity is studied for both perfect channel state information (CSI) and unknown CSI individually. The ergodic capacity with various SNR and Rician factors for different network configurations is also analyzed. The simulation results validate the effectiveness of the performance analysis. It is shown that the performance of the HAPs network in WSNs can be significantly improved by utilizing the MAV to achieve overlapping coverage, with the help of the V-MIMO techniques. PMID:26134102
-
Diversity Performance Analysis on Multiple HAP Networks
Directory of Open Access Journals (Sweden)
Feihong Dong
2015-06-01
Full Text Available One of the main design challenges in wireless sensor networks (WSNs is achieving a high-data-rate transmission for individual sensor devices. The high altitude platform (HAP is an important communication relay platform for WSNs and next-generation wireless networks. Multiple-input multiple-output (MIMO techniques provide the diversity and multiplexing gain, which can improve the network performance effectively. In this paper, a virtual MIMO (V-MIMO model is proposed by networking multiple HAPs with the concept of multiple assets in view (MAV. In a shadowed Rician fading channel, the diversity performance is investigated. The probability density function (PDF and cumulative distribution function (CDF of the received signal-to-noise ratio (SNR are derived. In addition, the average symbol error rate (ASER with BPSK and QPSK is given for the V-MIMO model. The system capacity is studied for both perfect channel state information (CSI and unknown CSI individually. The ergodic capacity with various SNR and Rician factors for different network configurations is also analyzed. The simulation results validate the effectiveness of the performance analysis. It is shown that the performance of the HAPs network in WSNs can be significantly improved by utilizing the MAV to achieve overlapping coverage, with the help of the V-MIMO techniques.
-
24 CFR 983.204 - When HAP contract is executed.
2010-04-01
... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false When HAP contract is executed. 983... When HAP contract is executed. (a) PHA inspection of housing. (1) Before execution of the HAP contract... into a HAP contract for any contract unit until the PHA has determined that the unit complies with the...
-
24 CFR 891.590 - Notice upon HAP contract expiration.
2010-04-01
... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Notice upon HAP contract expiration... Handicapped-Section 8 Assistance § 891.590 Notice upon HAP contract expiration. (a) Notice required. The HAP contract will provide that the Borrower will, at least one year before the end of the HAP contract term...
-
Energy Technology Data Exchange (ETDEWEB)
Becaro, A.A.; Paris, E.C.; Mattoso, L.H.C., E-mail: elaine.paris@embrapa.br [EMBRAPA Instrumentacao, Sao Carlos, SP (Brazil); Sciena, C.R.; Malafatti, J.D. [Universidade Federal de Sao Carlos (UFSCar), SP (Brazil). Departamento de Quimica
2016-07-01
Hydroxyapatite (HAP) belongs to the family of calcium apatites. In nanometric form (nHAP) can be used as a drug carrier. The objective was to improve PLA nanofibers with nHAP insert for use in drug delivery. nHAP were obtained by coprecipitation method and characterized by XRD and TEM techniques. PLA fibers (10%) and 5% nHAP were obtained at a distance of 6 cm and flow rate of 0.1, 0.3 and 0.5 ml h{sup -1}, and characterized by SEM. The nHAP were single phase with rod shape, rounded tip and from 10 to 20 nm in diameter. The fibers obtained from pure PLA had to be more porous than in the presence of HAP. The diameters ranged from 0.2 to 2.4 micrometers. Among the fibers obtained that showed the best result was to flow 0.3 ml h{sup -1}. (author)
-
Antenna Beam Pattern Characteristics of HAPS User Terminal
Ku, Bon-Jun; Oh, Dae Sub; Kim, Nam; Ahn, Do-Seob
High Altitude Platform Stations (HAPS) are recently considered as a green infrastructure to provide high speed multimedia services. The critical issue of HAPS is frequency sharing with satellite systems. Regulating antenna beam pattern using adaptive antenna schemes is one of means to facilitate the sharing with a space receiver for fixed satellite services on the uplink of a HAPS system operating in U bands. In this letter, we investigate antenna beam pattern characteristics of HAPS user terminals with various values of scan angles of main beam, null position angles, and null width.
-
24 CFR 983.205 - Term of HAP contract.
2010-04-01
... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Term of HAP contract. 983.205... DEVELOPMENT PROJECT-BASED VOUCHER (PBV) PROGRAM Housing Assistance Payments Contract § 983.205 Term of HAP contract. (a) Ten-year initial term. The PHA may enter into a HAP contract with an owner for an initial...
-
Hap1 and GABA: thinking about food intake.
Woods, Stephen C; Seeley, Randy J
2006-06-01
GABA stimulation of hypothalamic GABAA receptors increases food intake and body weight. Huntingtin-associated protein-1 (Hap1), is highly expressed in the hypothalamus and increases activity at GABAA receptors; mice lacking Hap1 are hypophagic. A recent paper (Sheng et al.,2006) further explores the role of Hap1 in the control of food intake.
-
Chitosan Fibers Modified with HAp/β–TCP Nanoparticles
Directory of Open Access Journals (Sweden)
Dariusz Wawro
2011-10-01
Full Text Available This paper describes a method for preparing chitosan fibers modified with hydroxyapatite (HAp, tricalcium phosphate (β-TCP, and HAp/β-TCP nanoparticles. Fiber-grade chitosan derived from the northern shrimp (Pandalus borealis and nanoparticles of tricalcium phosphate (β-TCP and hydroxyapatite (HAp suspended in a diluted chitosan solution were used in the investigation. Diluted chitosan solution containing nanoparticles of Hap/β-TCP was introduced to a 5.16 wt% solution of chitosan in 3.0 wt% acetic acid. The properties of the spinning solutions were examined. Chitosan fibers modified with nanoparticles of HAp/β-TCP were characterized by a level of tenacity and calcium content one hundred times higher than that of regular chitosan fibers.
-
40 CFR Table 7 to Subpart Vvvvvv... - Partially Soluble HAP
2010-07-01
... 40 Protection of Environment 14 2010-07-01 2010-07-01 false Partially Soluble HAP 7 Table 7 to... Pt. 63, Subpt. VVVVVV, Table 7 Table 7 to Subpart VVVVVV of Part 63—Partially Soluble HAP As required... partially soluble HAP listed in the following table. Partially soluble HAP name CAS No. 1. 1,1,1...
-
Optimization in obtaining PLA nanofibers/nHAP for pharmaceuticals release
International Nuclear Information System (INIS)
Becaro, A.A.; Paris, E.C.; Mattoso, L.H.C.; Sciena, C.R.; Malafatti, J.D.
2016-01-01
Hydroxyapatite (HAP) belongs to the family of calcium apatites. In nanometric form (nHAP) can be used as a drug carrier. The objective was to improve PLA nanofibers with nHAP insert for use in drug delivery. nHAP were obtained by coprecipitation method and characterized by XRD and TEM techniques. PLA fibers (10%) and 5% nHAP were obtained at a distance of 6 cm and flow rate of 0.1, 0.3 and 0.5 ml h"-"1, and characterized by SEM. The nHAP were single phase with rod shape, rounded tip and from 10 to 20 nm in diameter. The fibers obtained from pure PLA had to be more porous than in the presence of HAP. The diameters ranged from 0.2 to 2.4 micrometers. Among the fibers obtained that showed the best result was to flow 0.3 ml h"-"1. (author)
-
Tabatabaee Bafroee, Akram Sadat; Siadat, Seyed Davar; Mousavi, Seyed Fazlollah; Aghasadeghi, Mohammad Reza; Khorsand, Hashem; Nejati, Mehdi; Sadat, Seyed Mehdi; Mahdavi, Mehdi
2016-09-01
Hap, an auto-transporter protein, is an antigenically conserved adhesion protein which is present on both typeable and nontypeable Haemophilus influenzae. This protein has central role in bacterial attachment to respiratory tract epithelial cells. A 1000bp C-terminal fragment of Hap passenger domain (HapS) from nontypeable Haemophilus influenzae was cloned into a prokaryotic expression vector, pET-24a. BALB/c mice were immunized subcutaneously with purified rC-HapS. Serum IgG responses to purified rC-HapS, serum IgG subclasses were determined by ELISA and functional activity of antibodies was examined by Serum Bactericidal Assay. The output of rC-HapS was approximately 62% of the total bacterial proteins. Serum IgG responses were significantly increased in immunized group with rC-HapS mixed with Freund's adjuvant in comparison with control groups. Analysis of the serum IgG subclasses showed that the IgG1 subclass was predominant after subcutaneous immunization in BALB/c mice (IgG2a/IgG1 HapS immunized animals were strongly bactericidal against nontypeable Haemophilus influenzae. These results suggest that rC-HapS may be a potential vaccine candidate for nontypeable Haemophilus influenzae. Copyright © 2016 Elsevier Ltd. All rights reserved.
-
24 CFR 982.603 - SRO: Lease and HAP contract.
2010-04-01
... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false SRO: Lease and HAP contract. 982... Types Single Room Occupancy (sro) § 982.603 SRO: Lease and HAP contract. For SRO housing, there is a separate lease and HAP contract for each assisted person. ...
-
32 CFR 239.15 - List of HAP field offices.
2010-07-01
... 32 National Defense 2 2010-07-01 2010-07-01 false List of HAP field offices. 239.15 Section 239.15...) MISCELLANEOUS HOMEOWNERS ASSISTANCE PROGRAM-APPLICATION PROCESSING § 239.15 List of HAP field offices. Homeowners Assistance Program field offices that process HAP applications for installations and applicants...
-
24 CFR 982.455 - Automatic termination of HAP contract.
2010-04-01
... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Automatic termination of HAP contract. 982.455 Section 982.455 Housing and Urban Development Regulations Relating to Housing and Urban... Payments Contract and Owner Responsibility § 982.455 Automatic termination of HAP contract. The HAP...
-
Energy Technology Data Exchange (ETDEWEB)
Santos, T.L.; Leite, A.M.D.; Viana, K.M.S., E-mail: kalineviana@ect.ufrn.br [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil). Escola de Ciencias e Tecnologia
2016-07-01
The search for new materials for biomedical applications has led to investigation of the calcium phosphate bioceramics, and in particular hydroxyapatite (HAp), being a material similar to bone tissue, with excellent biocompatibility and high osteoconduction, enabling bone regeneration which allows the use at implants and prostheses. The synthesis of the nanometric HAp by combustion reaction enables obtaining the nanometric HAp with a more similar structure biological apatite as possible. This work aims to synthesize HAp by combustion reaction using two different routes of synthesis, first, using urea as fuel and the second using glycine, after this, evaluate the influence of fuels used in the microstructure of the hydroxyapatite obtained. The HAp obtained was characterized by: XRD, FTIR and SEM. Through analysis of the results, there is the synthesis conditions used that glycine has performed more favorable to obtaining HAp. (author)
-
Structural Determinants of Autoproteolysis of the Haemophilus influenzae Hap Autotransporter▿
Kenjale, Roma; Meng, Guoyu; Fink, Doran L.; Juehne, Twyla; Ohashi, Tomoo; Erickson, Harold P.; Waksman, Gabriel; St. Geme, Joseph W.
2009-01-01
Haemophilus influenzae is a gram-negative bacterium that initiates infection by colonizing the upper respiratory tract. The H. influenzae Hap autotransporter protein mediates adherence, invasion, and microcolony formation in assays with respiratory epithelial cells and presumably facilitates colonization. The serine protease activity of Hap is associated with autoproteolytic cleavage and extracellular release of the HapS passenger domain, leaving the Hapβ C-terminal domain embedded in the outer membrane. Cleavage occurs most efficiently at the LN1036-37 peptide bond and to a lesser extent at three other sites. In this study, we utilized site-directed mutagenesis, homology modeling, and assays with a peptide library to characterize the structural determinants of Hap proteolytic activity and cleavage specificity. In addition, we used homology modeling to predict the S1, S2, and S4 subsite residues of the Hap substrate groove. Our results indicate that the P1 and P2 positions at the Hap cleavage sites are critical for cleavage, with leucine preferred over larger hydrophobic residues or other amino acids in these positions. The substrate groove is formed by L263 and N274 at the S1 subsite, R264 at the S2 subsite, and E265 at the S4 subsite. This information may facilitate design of approaches to block Hap activity and interfere with H. influenzae colonization. PMID:19687208
-
Energy Technology Data Exchange (ETDEWEB)
R. Meij; B.H. Te Winkel [KEMA Power Generation & Sustainables, Arnhem (Netherlands)
2003-07-01
The emission limit values for coal-fired power stations in the European community and the Netherlands are described and compared in this paper. These limits are discussed in relation to the daily emissions in practice. Most attention is paid to heavy metals and other HAPS. The KEMA TRACE MODEL{reg_sign} can predict these elements fate. It is based on 25 years of research and predicts the distribution of elements over bottom ash, ESP ash, gypsum, emitted flue gases, sludge and effluent of the wastewater treatment plant. Next to this it predicts the composition of ash and flue gases. Wet FGD is the cause of a non-relation between the fuel composition and the emission into air for nearly most elements, except for some volatile elements (boron, bromine, chlorine, fluorine, mercury, iodine, sulphur and selenium). Although the emissions of these volatile elements are low, the concentrations are measured frequently, with emphasis on mercury, chlorine and fluorine. The consequences of co-combustion on emissions into air and the quality of by-products are discussed. The KEMA TRACE MODEL incorporates complicated EU regulations regarding co-combustion (the EU Waste Incineration Directive and the European Waste Catalogue). Modern coal-fired power stations in the Netherlands equipped with high-efficiency ESPs, wet FGD units and some with SCR meet the stringent present Dutch limits. Moreover, the quality of the by-products was such that a 100% of these by-products are sold as building materials. The increasing percentage of co-combustion hardly influences the emissions into air. However, more effort is necessary to maintain the quality of the by-products, but they can still be fully applied.
-
Characterization of a new sealer MTA/HAp
International Nuclear Information System (INIS)
Barros, C.M.B.; Oliveira, S.V.; Costa, A.C.F.M.; Dantas, D.C.R.E.; Fontes, L.B.C.; Viana, K.M.S.
2012-01-01
Filling materials (cement-based calcium hydroxide, amalgam, glass ionomer and IRM) are often used as sealers. However, none of them meets the desirable characteristics of a suitable sealing material. This study aims to characterize the new sealer, MTA/HAp from the incorporation of 5% by weight of synthetic hydroxyapatite to the MTA and to investigate the influence of the addition of HAp on the characteristic structural, chemical and consistency of the MTA. For this, we used MTA Angelus ® and HAp synthesized in the laboratory. We used the ratio by mass 95%MTA/5%HAp, where the hydroxyapatite added the characteristic of the MTA osteoconduction. The tests were performed: XRD, XRF and consistency. The results showed that both the new cement had the same crystalline phases as the same chemical composition of its precursors, yet having suitable consistency (plastic mass) of a sealer as well as the pure MTA. (author)
-
24 CFR 891.595 - HAP contract extension or renewal.
2010-04-01
... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false HAP contract extension or renewal... Handicapped-Section 8 Assistance § 891.595 HAP contract extension or renewal. Upon expiration of the term of the HAP contract, HUD and the Borrower may agree (subject to available funds) to extend the term of...
-
Spahich, Nicole A; Kenjale, Roma; McCann, Jessica; Meng, Guoyu; Ohashi, Tomoo; Erickson, Harold P; St Geme, Joseph W
2014-06-01
Haemophilus influenzae is a Gram-negative cocco-bacillus that initiates infection by colonizing the upper respiratory tract. Hap is an H. influenzae serine protease autotransporter protein that mediates adherence, invasion and microcolony formation in assays with human epithelial cells and is presumed to facilitate the process of colonization. Additionally, Hap mediates adherence to fibronectin, laminin and collagen IV, extracellular matrix (ECM) proteins that are present in the respiratory tract and are probably important targets for H. influenzae colonization. The region of Hap responsible for adherence to ECM proteins has been localized to the C-terminal 511 aa of the Hap passenger domain (HapS). In this study, we characterized the structural determinants of the interaction between HapS and fibronectin. Using defined fibronectin fragments, we established that Hap interacts with the fibronectin repeat fragment called FNIII(1-2). Using site-directed mutagenesis, we found a series of motifs in the C-terminal region of HapS that contribute to the interaction with fibronectin. Most of these motifs are located on the F1 and F3 faces of the HapS structure, suggesting that the F1 and F3 faces may be responsible for the HapS-fibronectin interaction. © 2014 The Authors.
-
Directory of Open Access Journals (Sweden)
Nataliya Petryk
Full Text Available The transcriptional regulator HAP4, induced by respiratory substrates, is involved in the balance between fermentation and respiration in S. cerevisiae. We identified putative orthologues of the Hap4 protein in all ascomycetes, based only on a conserved sixteen amino acid-long motif. In addition to this motif, some of these proteins contain a DNA-binding motif of the bZIP type, while being nonetheless globally highly divergent. The genome of the yeast Hansenula polymorpha contains two HAP4-like genes encoding the protein HpHap4-A which, like ScHap4, is devoid of a bZIP motif, and HpHap4-B which contains it. This species has been chosen for a detailed examination of their respective properties. Based mostly on global gene expression studies performed in the S. cerevisiae HAP4 disruption mutant (ScΔhap4, we show here that HpHap4-A is functionally equivalent to ScHap4, whereas HpHap4-B is not. Moreover HpHAP4-B is able to complement the H2O2 hypersensitivity of the ScYap1 deletant, YAP1 being, in S. cerevisiae, the main regulator of oxidative stress. Finally, a transcriptomic analysis performed in the ScΔyap1 strain overexpressing HpHAP4-B shows that HpHap4-B acts both on oxidative stress response and carbohydrate metabolism in a manner different from both ScYap1 and ScHap4. Deletion of these two genes in their natural host, H. polymorpha, confirms that HpHAP4-A participates in the control of the fermentation/respiration balance, while HpHAP4-B is involved in oxidative stress since its deletion leads to hypersensitivity to H2O2. These data, placed in an evolutionary context, raise new questions concerning the evolution of the HAP4 transcriptional regulation function and suggest that Yap1 and Hap4 have diverged from a unique regulatory protein in the fungal ancestor.
-
24 CFR 982.607 - Congregate housing: Lease and HAP contract.
2010-04-01
... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Congregate housing: Lease and HAP... Types Congregate Housing § 982.607 Congregate housing: Lease and HAP contract. For congregate housing, there is a separate lease and HAP contract for each assisted family. ...
-
Comparison of Broadband Wireless Access Technology for HAPS Communication
Directory of Open Access Journals (Sweden)
Mingxiang GUAN
2014-03-01
Full Text Available An information system formed by HAP (High Altitude Platform will be a new generation-system for the wireless communications and HAPS (HAP Station communication system combines the advantages of both terrestrial and satellite communication systems and avoids, to different extents, their disadvantages. Third generation (3G mobile technology which is specified by the third generation partnership project (3 GPP is definitely one of the candidates. With the success of wireless network, the IEEE 802.16 standard, with its wireless metropolitan area network (MAN air interface appears to be a strong competitor. We provide initial practical comparison of these two technologies for HAPS Communication.
-
24 CFR 982.611 - Group home: Lease and HAP contract.
2010-04-01
... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Group home: Lease and HAP contract... Types Group Home § 982.611 Group home: Lease and HAP contract. For assistance in a group home, there is a separate HAP contract and lease for each assisted person. ...
-
24 CFR 982.454 - Termination of HAP contract: Insufficient funding.
2010-04-01
... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Termination of HAP contract... Assistance Payments Contract and Owner Responsibility § 982.454 Termination of HAP contract: Insufficient funding. The PHA may terminate the HAP contract if the PHA determines, in accordance with HUD requirements...
-
24 CFR 982.616 - Shared housing: Lease and HAP contract.
2010-04-01
... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Shared housing: Lease and HAP... Types Shared Housing § 982.616 Shared housing: Lease and HAP contract. For assistance in a shared housing unit, there is a separate HAP contract and lease for each assisted family. ...
-
Air emissions inventory for the Idaho National Engineering Laboratory -- 1995 emissions report
International Nuclear Information System (INIS)
1996-06-01
This report presents the 1995 update of the Air Emission Inventory for the Idaho National Engineering Laboratory (INEL). The INEL Air Emission Inventory documents sources and emissions of non-radionuclide pollutants from operations at the INEL. The report describes the emission inventory process and all of the sources at the INEL, and provides non-radionuclide emissions estimates for stationary sources. The air contaminants reported include nitrogen oxides, sulfur oxides, carbon monoxide, volatile organic compounds, particulates, and hazardous air pollutants (HAPs)
-
Air emissions inventory for the Idaho National Engineering Laboratory -- 1995 emissions report
Energy Technology Data Exchange (ETDEWEB)
NONE
1996-06-01
This report presents the 1995 update of the Air Emission Inventory for the Idaho National Engineering Laboratory (INEL). The INEL Air Emission Inventory documents sources and emissions of non-radionuclide pollutants from operations at the INEL. The report describes the emission inventory process and all of the sources at the INEL, and provides non-radionuclide emissions estimates for stationary sources. The air contaminants reported include nitrogen oxides, sulfur oxides, carbon monoxide, volatile organic compounds, particulates, and hazardous air pollutants (HAPs).
-
Integrated Sensing of Alcohols by CNT Blended HAp Nano Ceramics
Directory of Open Access Journals (Sweden)
Shaikh R. ANJUM
2016-11-01
Full Text Available The research work reports the application of carbon nanotubes (CNT blended Hydroxyapatite (HAp composites as ideal thick film substrates for the detection of hazardous and flammable methanol vapours. The main objective of this work is to improve the temperature-dependent sensitivity of the sensor for the detection of lower methanol concentration. In this study, the sensing ability of native HAp and CNT blended HAp thick films is studied for the detection of methanol vapours present in ambient air individually and in the form of a mixture of methanol, ethanol, and propanol. The sensing parameters are studied using two probe electrical method. The sensor substrate is made by means of doping of different concentrations of CNT in HAp. The sensing of methanol vapours is studied at a fixed concentration of 100 ppm. Native HAp substrate shows good sensitivity for methanol at room temperature; however, its sensing performance is inferior to the CNT blended materials. The blended composites exhibit impressive sensing ability compared with native HAp in terms of sensitivity, response/ recovery time and maximum uptake limit. The sensing mechanism for methanol detection, the role of HAp as a parent material and CNT as an additive, is explained using a suitable sensing mechanism.
-
Air Emissions Factors and Quantification
Emissions factors are used in developing air emissions inventories for air quality management decisions and in developing emissions control strategies. This area provides technical information on and support for the use of emissions factors.
-
HAP1 gene expression is associated with radiosensitivity in breast cancer cells
International Nuclear Information System (INIS)
Wu, Jing; Zhang, Jun-ying; Yin, Li; Wu, Jian-zhong; Guo, Wen-jie; Wu, Jian-feng; Chen, Meng; Xia, You-you; Tang, Jin-hai; Ma, Yong-chao; He, Xia
2015-01-01
Highlights: • Overexpression of HAP1 gene promotes apoptosis in MCF-7 cells after irradiation. • HAP1 reduces tumor volume in nude mice xenograft models after irradiation. • HAP1 increases radiosensitivity of breast cancer cells in vitro and vivo. - Abstract: Objectives: The purpose of this study was to investigate the relationship between huntingtin-associated protein1 (HAP1) gene and radiation therapy of breast cancer cells. Methods: HAP1 gene was transfected into breast cancer MCF-7 cells, which was confirmed by quantitative reverse transcription-polymerase chain reaction analysis (qRT-PCR) and Western blot in vitro. The changes of cell radiosensitivity were assessed by colony formation assay. Apoptosis were examined by flow cytometry. The expressions of two radiation-induced genes were evaluated by Western blot. Tumor growth was investigated in nude mice xenograft models in vivo. Results: Our data showed that HAP1 gene expression was significantly increased in HAP1-transfected MCF-7 cells in comparison with the parental cells or negative control cells. The survival rate in MCF-7/HAP1 cells was significantly decreased after irradiation (0, 2, 4, 6, 8 Gy), compared to cells in MCF-7 and MCF-7/Pb groups in vitro. HAP1 gene increased apoptosis in MCF-7 cells after irradiation. Additionally, the tumor volume and weight in MCF-7/HAP1 + RT group were observably lower than in MCF-7/HAP1 group and MCF-7/Pb + RT group. Conclusion: The present study indicated that HAP1 gene expression was related to the radiosensitivity of breast cancer cells and may play an important role in the regulation of cellular radiosensitivity
-
Is HAPS Viable for the Next-Generation Telecommunication Platform in Korea?
Jonghwa Kim; Deokjoo Lee; Jaekyoung Ahn; Do-Seob Ahn; Bon-Jun Ku
2008-01-01
Abstract HAPS is a promising technology capable of providing broadband multimedia services as an alternative to the satellite communication system or terrestrial network. In this study, economic aspects of HAPS service are analyzed, HAPS services are defined, and revenues from the defined services are forecasted assuming nine scenarios. Capital expenditure as well as operating expenditure is estimated. To evaluate the profitability of HAPS service, the net present value (NPV), payback period,...
-
Fabrication of CTP/HAp novel gradient composite bioceramics
Institute of Scientific and Technical Information of China (English)
无
2007-01-01
Calcium-titanium-phosphate(CaTi4(PO4)6, CTP)/hydroxyapatite(HAp) is a kind of novel gradient composite bioceramics,which has excellent biocompatibility and bioactivity. CTP ceramic film was synthesized one-step on the surface of titanium using micro-arc oxidation(MAO). The CTP/HAp composite bioceramics were prepared by soaking CTP film in HAp inducing solution for several days. XRD, SEM and EDX were used to characterize the bio-ceramic films phase and composition, morphology and component. The influence of electrolyte molar ratio of Ca to P and the current density to the synthesis of film was studied, and the optimized value of parameters above were 1/6 and 15A/dm2. The parameters of HAp inducing solution, such as component and pH value were also studied and the best pH value which is adjusted by NaOH is 6.4.
-
Analysis of the fuel influence in obtaining HAp by combustion reaction
International Nuclear Information System (INIS)
Santos, T.L.; Leite, A.M.D.; Viana, K.M.S.
2016-01-01
The search for new materials for biomedical applications has led to investigation of the calcium phosphate bioceramics, and in particular hydroxyapatite (HAp), being a material similar to bone tissue, with excellent biocompatibility and high osteoconduction, enabling bone regeneration which allows the use at implants and prostheses. The synthesis of the nanometric HAp by combustion reaction enables obtaining the nanometric HAp with a more similar structure biological apatite as possible. This work aims to synthesize HAp by combustion reaction using two different routes of synthesis, first, using urea as fuel and the second using glycine, after this, evaluate the influence of fuels used in the microstructure of the hydroxyapatite obtained. The HAp obtained was characterized by: XRD, FTIR and SEM. Through analysis of the results, there is the synthesis conditions used that glycine has performed more favorable to obtaining HAp. (author)
-
A dynamic, efficient, and flexible metal HAP standard for petroleum refinery FCCs
Energy Technology Data Exchange (ETDEWEB)
Rao, P. [Pennsylvania State Univ., University Park, PA (United States)
2000-07-01
The Petroleum Refinery Maximum Achievable Control Technology (MACT) II standards were recently announced by the United States Environmental Protection Agency. The standards are designed to control hazardous air pollutants (HAPs) from fluid catalytic cracking (FCC), catalytic reforming and sulfur recovery units. The major role of feed quality in determining emissions of heavy metals, sulfur oxides (SOx) and nitrous oxides from FCC vents were discussed. The impact of FCC feed quality on carbon dioxide emissions was also examined. Some potential loopholes in the SOx new source performance standard for FCCs were also identified. This paper also outlined regulatory issues that occur when pollutant emission rates vary with raw material or fuel quantity. When input qualities vary, the format of emission standards take on special meaning. In particular, proportional control standards perform poorly resulting in environmentally damaged inputs. Precautions should be taken in profit-induced moves to avoid lower quality inputs, particularly at this time for setting new directions for a cleaner environment. 22 refs., 2 tabs., 10 figs.
-
Is HAPS Viable for the Next-Generation Telecommunication Platform in Korea?
Directory of Open Access Journals (Sweden)
Jonghwa Kim
2008-07-01
Full Text Available HAPS is a promising technology capable of providing broadband multimedia services as an alternative to the satellite communication system or terrestrial network. In this study, economic aspects of HAPS service are analyzed, HAPS services are defined, and revenues from the defined services are forecasted assuming nine scenarios. Capital expenditure as well as operating expenditure is estimated. To evaluate the profitability of HAPS service, the net present value (NPV, payback period, and the internal rate of return (IRR are calculated. The results show that HAPS is economically justifiable in all the scenarios. Assuming that ARPU for the service is $35 per month in the average scenario, NPV is calculated as $2964 million, IRR becomes 31.9%, and payback occurs in 2017, which implies that HAPS service is profitable in Korea. In addition, the results of the sensitivity analysis show that the results are fairly robust.
-
Is HAPS Viable for the Next-Generation Telecommunication Platform in Korea?
Directory of Open Access Journals (Sweden)
Lee Deokjoo
2008-01-01
Full Text Available Abstract HAPS is a promising technology capable of providing broadband multimedia services as an alternative to the satellite communication system or terrestrial network. In this study, economic aspects of HAPS service are analyzed, HAPS services are defined, and revenues from the defined services are forecasted assuming nine scenarios. Capital expenditure as well as operating expenditure is estimated. To evaluate the profitability of HAPS service, the net present value (NPV, payback period, and the internal rate of return (IRR are calculated. The results show that HAPS is economically justifiable in all the scenarios. Assuming that ARPU for the service is $35 per month in the average scenario, NPV is calculated as $2964 million, IRR becomes 31.9%, and payback occurs in 2017, which implies that HAPS service is profitable in Korea. In addition, the results of the sensitivity analysis show that the results are fairly robust.
-
[Optimized isolation and purification of non-typeable Haemophilus influenzae Haps protein].
Li, Wan-yi; Kuang, Yu; Li, Ming-yuan; Yang, Yuan; Jiang, Zhong-hua; Yao, Feng; Chen, Chang-chun
2007-12-01
To optimize the isolation and purification conditions for Hap(s) protein of non-typeable Haemophilus influenzae. Hap(s) protein was purified by ammonium sulfate precipitation, dialysis desalting and Hitrap weak cation exchange columns of CM Sepharose Fast Flow. The condition of the elution was optimized for pH and ionic strength, the absorbance at 280 nm of the elution samples were detected, and the targeted protein band in the collected samples was observed by SDS-PAGE electrophoresis. The Hitrap ion exchange column was eluted with buffer 1, which resulted in a baseline distribution of absorbance at 280 nm. Buffer 2 elution of the column resulted in the presence of peak absorbance with trails, which was identified to be constituted by some low molecular weight bands by subsequent SDS-PAGE. In serial column elution with buffer 3 with different ionic strength, a peak absorbance was observed with the ionic strength of 100 mmol/L NaCl, and SDS-PAGE confirmed that the peak was generated by the target protein. No obvious peaks or bands in SDS-PAGE occurred with the other ionic strengths. The pH of the buffer only affect the elution of the irrelevant proteins rather than the Hap(s) protein, and elution with the buffer containing 100 mmol/L NaCl can be optimal for eluting the Hap(s) protein.
-
Age at onset in Huntington's disease: replication study on the association of HAP1.
Karadima, Georgia; Dimovasili, Christina; Koutsis, Georgios; Vassilopoulos, Demetris; Panas, Marios
2012-11-01
In recent years two association studies investigating the HAP1 T441M (rs4523977) polymorphism as a potential modifying factor of the age at onset (AAO) of Huntington's disease (HD), have been reported. Initially evidence for association was found between the M441 risk allele and the AAO. Subsequently, a second study, although failing to replicate these findings, found evidence for association between the same risk allele and AAO of motor symptoms (mAAO). In the present study, the role of the HAP1 T441M polymorphism as a modifier of the AAO in HD was investigated in a cohort of 298 Greek HD patients. In this cohort the CAG repeat number accounted for 55% of the variance in AAO. No association was found between the HAP1 T441M polymorphism and the AAO of HD. © 2012 Elsevier Ltd. All rights reserved.
-
Fate of trace element haps when applying mercury control technologies
Energy Technology Data Exchange (ETDEWEB)
Nyberg, Carolyn M.; Thompson, Jeffrey S.; Zhuang, Ye; Pavlish, John H. [University of North Dakota Energy and Environmental Research Center 15 North 23rd Street, Stop 9018, Grand Forks, North Dakota 58202-9018 (United States); Brickett, Lynn; Pletcher, Sara [U.S. Department of Energy National Energy Technology Laboratory 626 Cochrans Mill Road, PO Box 10940, MS 922-273C, Pittsburgh, PA 15236-0940 (United States)
2009-11-15
During the past several years, and particularly since the Clean Air Mercury Rule (CAMR) was promulgated in June of 2005, the electric utility industry, product vendors, and the research community have been working diligently to develop and test Hg control strategies for a variety of coal types and plant configurations. Some of these strategies include sorbent injection and chemical additives designed to increase mercury capture efficiency in particulate control devices. These strategies have the potential to impact the fate of other inorganic hazardous air pollutants (HAPs), which typically include As, Be, Cd, Cr, Co, Mn, Ni, Pb, Se, and Sb. To evaluate this impact, flue gas samples using EPA Method 29, along with representative coal and ash samples, were collected during recent pilot-scale and field test projects that were evaluating Hg control technologies. These test programs included a range of fuel types with varying trace element concentrations, along with different combustion systems and particulate control devices. The results show that the majority of the trace element HAPs are associated with the particulate matter in the flue gas, except for Se. However, for five of the six projects, Se partitioning was shifted to the particulate phase and total emissions reduced when Hg control technologies were applied. (author)
-
40 CFR 63.494 - Back-end process provisions-residual organic HAP limitations.
2010-07-01
... organic HAP limitations. 63.494 Section 63.494 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... § 63.494 Back-end process provisions—residual organic HAP limitations. (a) The monthly weighted average residual organic HAP content of all grades of elastomer processed, measured after the stripping operation...
-
24 CFR 982.403 - Terminating HAP contract when unit is too small.
2010-04-01
... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Terminating HAP contract when unit... Terminating HAP contract when unit is too small. (a) Violation of HQS space standards. (1) If the PHA... by the family, the PHA must terminate the HAP contract in accordance with its terms. (b) Certificate...
-
Mackenzie, Kimberly D; Lim, Yoon; Duffield, Michael D; Chataway, Timothy; Zhou, Xin-Fu; Keating, Damien J
2017-07-01
Huntingtin-associated protein 1 (HAP1) was initially identified as a binding partner of huntingtin, mutations in which underlie Huntington's disease. Subcellular localization and protein interaction data indicate that HAP1 may be important in vesicle trafficking, cell signalling and receptor internalization. In this study, a proteomics approach was used for the identification of novel HAP1-interacting partners to attempt to shed light on the physiological function of HAP1. Using affinity chromatography with HAP1-GST protein fragments bound to Sepharose columns, this study identified a number of trafficking-related proteins that bind to HAP1. Interestingly, many of the proteins that were identified by mass spectrometry have trafficking-related functions and include the clathrin light chain B and Sec23A, an ER to Golgi trafficking vesicle coat component. Using co-immunoprecipitation and GST-binding assays the association between HAP1 and clathrin light chain B has been validated in vitro. This study also finds that HAP1 co-localizes with clathrin light chain B. In line with a physiological function of the HAP1-clathrin interaction this study detected a dramatic reduction in vesicle retrieval and endocytosis in adrenal chromaffin cells. Furthermore, through examination of transferrin endocytosis in HAP1 -/- cortical neurons, this study has determined that HAP1 regulates neuronal endocytosis. In this study, the interaction between HAP1 and Sec23A was also validated through endogenous co-immunoprecipitation in rat brain homogenate. Through the identification of novel HAP1 binding partners, many of which have putative trafficking roles, this study provides us with new insights into the mechanisms underlying the important physiological function of HAP1 as an intracellular trafficking protein through its protein-protein interactions. Copyright © 2017 Elsevier Inc. All rights reserved.
-
Characterization of biomimetically synthesized Hap-Gel nanocomposites as bone substitute
International Nuclear Information System (INIS)
Bera, Tanmay; Vivek, A N; Saraf, S K; Ramachandrarao, P
2008-01-01
There is an increasing demand for an affordable and easy-to-fabricate material to help patients having a long bone gap. In this paper, we describe the biomimetic synthesis of Hap-Gel in situ nanocomposite powders with varied proportions. Their biocompatibility and bone regeneration abilities were assessed on a rabbit model. The use of Hap crystals and Gel molecule, the soluble form of bone protein, makes the nanocomposites comparable to natural bone in constituents. The application of biomimetic principles improves crystal morphology and the interaction of Hap crystals with the Gel molecules as seen through in vitro characterizations. Out of the various compositions studied, one with 80:20 proportions of Hap to Gel proved to be closest to the characteristics of natural bone. The immunological response to this composite, assessed through intradermal inoculation, did not reveal any reaction. The in vivo implantation studies in the femoral condyle of the animals, as assessed by serial post-operative follow-up radiography and the histological evaluation, revealed a good biocompatibility and bone-regeneration ability of the material. Thus, nanocomposites of Hap-Gel have a great potential for serving as an effective and affordable biomaterial for bone grafting applications
-
Coexistence of Terrestrial and HAP 3G Networks during Disaster Scenarios
Directory of Open Access Journals (Sweden)
P. Pechac
2008-12-01
Full Text Available The aim of this paper is to show the possible coexistence of an HAP and a terrestrial component of 3G networks at a single carrier frequency. The main goal is to compare the basic parameters of terrestrial and HAP com-ponent 3G networks modeled in suburban (macrocell and urban (macro/microcell areas and to demonstrate the way they impact on each other. This study should present what we assume are the better capabilities of HAP 3G networks compared to their terrestrial counterparts. The parameters of the HAP and terrestrial component of 3G networks, were the terrestrial cells to be disabled during disasters, are also presented.
-
POLLUTION PREVENTION CASE STUDIES: LOW-VOC/HAP WOOD FURNITURE COATINGS
This article provides a brief profile of the wood furniture industry, discusses pollution prevention activities typically implemented, describes the four low-VOC/HAP coating technologies studied. and summarizes one case study for each of the low-VOC/HAP coating yechnologies inves...
-
Biochemical Removal of HAP Precursors from Coal
Energy Technology Data Exchange (ETDEWEB)
Olson, Gregory J
1997-05-12
Column biooxidation tests with Kentucky coal confirmed results of earlier shake flask tests showing significant removal from the coal of arsenic, selenium, cobalt, manganese, nickel and cadmium. Rates of pyrite biooxidation in Kentucky coal were only slightly more than half the rates found previously for Indiana and Pittsburgh coals. Removal of pyrite from Pittsburgh coal by ferric ion oxidation slows markedly as ferrous ions accumulate in solution, requiring maintenance of high redox potentials in processes designed for removal of pyrite and hazardous air pollutant (HAP) precursors by circulation of ferric solutions through coal. The pyrite oxidation rates obtained in these tests were used by Unifield Engineering to support the conceptual designs for alternative pyrite and HAP precursor bioleaching processes for the phase 2 pilot plant. Thermophilic microorganisms were tested to determine if mercury could be mobilized from coal under elevated growth temperatures. There was no evidence for mercury removal from coal under these conditions. However, the activity of the organisms may have liberated mercury physically. It is also possible that the organisms dissolved mercury and it readsorbed to the clay preferentially. Both of these possibilities are undergoing further testing. The Idaho National Engineering and Environmental Laboratory's (INEEL) slurry column reactor was operated and several batches of feed coal, product coal, waste solids and leach solutions were submitted to LBL for HAP precursor analysis. Results to date indicate significant removal of mercury, arsenic and other HAP precursors in the combined physical-biological process.
-
Zhou, Zheng; Hu, Taishan; Zhou, Xue; Wildum, Steffen; Garcia-Alcalde, Fernando; Xu, Zhiheng; Wu, Daitze; Mao, Yi; Tian, Xiaojun; Zhou, Yuan; Shen, Fang; Zhang, Zhisen; Tang, Guozhi; Najera, Isabel; Yang, Guang; Shen, Hong C.; Young, John A. T.; Qin, Ning
2017-01-01
Heteroaryldihydropyrimidine (HAP) and sulfamoylbenzamide (SBA) are promising non-nucleos(t)ide HBV replication inhibitors. HAPs are known to promote core protein mis-assembly, but the molecular mechanism of abnormal assembly is still elusive. Likewise, the assembly status of core protein induced by SBA remains unknown. Here we show that SBA, unlike HAP, does not promote core protein mis-assembly. Interestingly, two reference compounds HAP_R01 and SBA_R01 bind to the same pocket at the dimer-dimer interface in the crystal structures of core protein Y132A hexamer. The striking difference lies in a unique hydrophobic subpocket that is occupied by the thiazole group of HAP_R01, but is unperturbed by SBA_R01. Photoaffinity labeling confirms the HAP_R01 binding pose at the dimer-dimer interface on capsid and suggests a new mechanism of HAP-induced mis-assembly. Based on the common features in crystal structures we predict that T33 mutations generate similar susceptibility changes to both compounds. In contrast, mutations at positions in close contact with HAP-specific groups (P25A, P25S, or V124F) only reduce susceptibility to HAP_R01, but not to SBA_R01. Thus, HAP and SBA are likely to have distinctive resistance profiles. Notably, P25S and V124F substitutions exist in low-abundance quasispecies in treatment-naïve patients, suggesting potential clinical relevance. PMID:28205569
-
40 CFR 63.5340 - How do I determine the allowable HAP loss?
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true How do I determine the allowable HAP... Requirements § 63.5340 How do I determine the allowable HAP loss? (a) By the fifteenth of each month, you must determine the allowable HAP loss in pounds from your leather finishing operation for the previous month. (b...
-
40 CFR 63.5335 - How do I determine the actual HAP loss?
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true How do I determine the actual HAP loss... Requirements § 63.5335 How do I determine the actual HAP loss? (a) This section describes the information and procedures you must use to determine the actual HAP loss from your leather finishing operation. By the...
-
CO2 Emission Factors for Coals
Directory of Open Access Journals (Sweden)
P. Orlović-Leko
2015-03-01
Full Text Available Emission factors are used in greenhouse gas inventories to estimate emissions from coal combustion. In the absence of direct measures, emissions factors are frequently used as a quick, low cost way to estimate emissions values. Coal combustion has been a major contributor to the CO2 flux into the atmosphere. Nearly all of the fuel carbon (99 % in coal is converted to CO2 during the combustion process. The carbon content is the most important coal parameter which is the measure of the degree of coalification (coal rank. Coalification is the alteration of vegetation to form peat, succeeded by the transformation of peat through lignite, sub-bituminous, bituminous to anthracite coal. During the geochemical or metamorphic stage, the progressive changes that occur within the coal are an increase in the carbon content and a decrease in the hydrogen and oxygen content resulting in a loss of volatiles. Heterogeneous composition of coal causes variation in CO2 emission from different coals. The IPCC (Intergovernmental Panel on Climate Change has produced guidelines on how to produce emission inventories which includes emission factors. Although 2006 IPCC Guidelines provided the default values specified according to the rank of the coal, the application of country-specific emission factors was recommended when estimating the national greenhouse gas emissions. This paper discusses the differences between country-specific emission factors and default IPCC CO2 emission factors, EF(CO2, for coals. Also, this study estimated EF(CO2 for two different types of coals and peat from B&H, on the basis fuel analyses. Carbon emission factors for coal mainly depend on the carbon content of the fuel and vary with both rank and geographic origin, which supports the idea of provincial variation of carbon emission factors. Also, various other factors, such as content of sulphur, minerals and macerals play an important role and influence EF(CO2 from coal. Carbonate minerals
-
Reducing VOC Press Emission from OSB Manufacturing
Energy Technology Data Exchange (ETDEWEB)
Dr. Gary D. McGinnis; Laura S. WIlliams; Amy E. Monte; Jagdish Rughani: Brett A. Niemi; Thomas M. Flicker
2001-12-31
Current regulations require industry to meet air emission standards with regard to particulates, volatile organic compounds (VOCs), hazardous air pollutants (HAPs) and other gases. One of many industries that will be affected by the new regulations is the wood composites industry. This industry generates VOCs, HAPs, and particulates mainly during the drying and pressing of wood. Current air treatment technologies for the industry are expensive to install and operate. As regulations become more stringent, treatment technologies will need to become more efficient and cost effective. The overall objective of this study is to evaluate the use of process conditions and chemical additives to reduce VOC/HAPs in air emitted from presses and dryers during the production of oriented strand board.
-
Ridenour, John B; Smith, Jonathon E; Bluhm, Burton H
2016-09-01
Contamination of maize ( Zea mays ) with fumonisins produced by the fungus Fusarium verticillioides is a global concern for food safety. Fumonisins are a group of polyketide-derived secondary metabolites linked to esophageal cancer and neural tube birth defects in humans and numerous toxicoses in livestock. Despite the importance of fumonisins in global maize production, the regulation of fumonisin biosynthesis during kernel pathogenesis is poorly understood. The HAP complex is a conserved, heterotrimeric transcriptional regulator that binds the consensus sequence CCAAT to modulate gene expression. Recently, functional characterization of the Hap3 subunit linked the HAP complex to the regulation of secondary metabolism and stalk rot pathogenesis in F. verticillioides . Here, we determine the involvement of HAP3 in fumonisin biosynthesis and kernel pathogenesis. Deletion of HAP3 suppressed fumonisin biosynthesis on both nonviable and live maize kernels and impaired pathogenesis in living kernels. Transcriptional profiling via RNA sequencing indicated that the HAP complex regulates at least 1,223 genes in F. verticillioides , representing nearly 10% of all predicted genes. Disruption of the HAP complex caused the misregulation of biosynthetic gene clusters underlying the production of secondary metabolites, including fusarins. Taken together, these results reveal that the HAP complex is a central regulator of fumonisin biosynthesis and kernel pathogenesis and works as both a positive and negative regulator of secondary metabolism in F. verticillioides .
-
International Nuclear Information System (INIS)
Humphreys, M.P.
1995-01-01
Title 3 of the 1990 Clean Air Act (CAA) Amendments addresses the emissions of 189 hazardous air pollutants (HAPs) and mandates that EPA develop technology-based [Maximum Achievable Control Technology (MACT)] standards for the control of these pollutants from approximately 174 source categories. After implementation of technology-based standards, EPA is required to further evaluate ''residual risk'' from HAP emissions, and, if required, develop more stringent standards to protect human health and the environment with an ''adequate margin of safety''. Recognizing that EPA will be issuing risk-based regulations after MACT standards have been implemented, the US Department of Energy (DOE), Oak Ridge Operations Office (ORO) has conducted an evaluation of ambient air impacts of HAP emissions from its installations located on the Oak Ridge Reservation (ORR) near Oak Ridge, Tennessee. This report provides results of atmospheric dispersion modeling conducted to determine ambient air impacts of HAP emissions from facilities located on the ORR
-
International Nuclear Information System (INIS)
Pilmane, M; Salms, G; Salma, I; Skagers, A; Locs, J; Loca, D; Berzina-Cimdina, L
2011-01-01
Proinflammatory cytokines mediate bone loss around the implants in patients with peri-implant disease. However, there is no complete data about the expression of cytokines into the bone around the implants. The aim of this work was to investigate the distribution and appearance of inflammatory cytokines and anti-inflammatory proteins in the bone of jaw of experimental rabbits in different time periods after HAp implantation. Material was obtained from 8 rabbits in lower jaw 6 and 8 months after HAp implants were placed. Tissues were processed for immunohistochemical detection of tumor necrosis factor alfa (TNFα), Interleukin 1, 6, 8, 10 (IL-1, IL-6, IL-8, IL-10) and defensin 2. Results demonstrated practically unchanged expression of IL-6 and IL-10 between both - experimental and control side 6 months after implantation, while IL-1 and IL-8 notably increased in control side. IL-1 and IL-10 expression did not change in either the experimental side nor the controle side after 8 months HAP implantation, but IL-6 and IL-8 demonstrated a decrease in the control sites. Only IL-8 was elevated with time in experimental sites, while IL-10 showed individual variations in 2 cases.
-
Energy Technology Data Exchange (ETDEWEB)
Pilmane, M [Riga Stradins University, Institute of Anatomy and Anthropology, Dzirciema 16, LV-1007, Riga (Latvia); Salms, G; Salma, I; Skagers, A [Riga Stradins University, Department of Oral and Maxillofacial Surgery, Dzirciema 20. LV-1007, Riga (Latvia); Locs, J; Loca, D; Berzina-Cimdina, L, E-mail: pilmane@latnet.lv [Riga Technical University, Riga Biomaterials innovation and development centre, Pulka 3/3, LV-1007, Riga (Latvia)
2011-06-23
Proinflammatory cytokines mediate bone loss around the implants in patients with peri-implant disease. However, there is no complete data about the expression of cytokines into the bone around the implants. The aim of this work was to investigate the distribution and appearance of inflammatory cytokines and anti-inflammatory proteins in the bone of jaw of experimental rabbits in different time periods after HAp implantation. Material was obtained from 8 rabbits in lower jaw 6 and 8 months after HAp implants were placed. Tissues were processed for immunohistochemical detection of tumor necrosis factor alfa (TNF{alpha}), Interleukin 1, 6, 8, 10 (IL-1, IL-6, IL-8, IL-10) and defensin 2. Results demonstrated practically unchanged expression of IL-6 and IL-10 between both - experimental and control side 6 months after implantation, while IL-1 and IL-8 notably increased in control side. IL-1 and IL-10 expression did not change in either the experimental side nor the controle side after 8 months HAP implantation, but IL-6 and IL-8 demonstrated a decrease in the control sites. Only IL-8 was elevated with time in experimental sites, while IL-10 showed individual variations in 2 cases.
-
40 CFR Table 3 to Subpart Ggg of... - Soluble HAP
2010-07-01
... 40 Protection of Environment 11 2010-07-01 2010-07-01 true Soluble HAP 3 Table 3 to Subpart GGG of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED... HAP Compound 1,1-Dimethylhydrazine. 1,4-Dioxane. Acetonitrile. Acetophenone. Diethyl sulfate. Dimethyl...
-
Particulate Matter Emission Factors for Biomass Combustion
Directory of Open Access Journals (Sweden)
Simone Simões Amaral
2016-10-01
Full Text Available Emission factor is a relative measure and can be used to estimate emissions from multiple sources of air pollution. For this reason, data from literature on particulate matter emission factors from different types of biomass were evaluated in this paper. Initially, the main sources of particles were described, as well as relevant concepts associated with particle measurements. In addition, articles about particle emissions were classified and described in relation to the sampling environment (open or closed and type of burned biomass (agricultural, garden, forest, and dung. Based on this analysis, a set of emission factors was presented and discussed. Important observations were made about the main emission sources of particulate matter. Combustion of compacted biomass resulted in lower particulate emission factors. PM2.5 emissions were predominant in the burning of forest biomass. Emission factors were more elevated in laboratory burning, followed by burns in the field, residences and combustors.
-
Advanced Emissions Control Development Program: Mercury Control
International Nuclear Information System (INIS)
Evans, A.P.; Redinger, K.W.; Holmes, M.J.
1997-07-01
McDermott Technology, Inc. (a subsidiary of Babcock ampersand Wilcox) is conducting the Advanced Emissions Control Development Project (AECDP) which is aimed at the development of practical, cost-effective strategies for reducing the emissions of hazardous air pollutants (HAPS) from coal-fired electric utility plants. The need for such controls may arise as the US Environmental Protection Agency (EPA) proceeds with implementation of requirements set forth in the Clean Air Act Amendments (CAAA's) of 1990. Promulgation of air toxics emissions regulations for electric utility plants could dramatically impact utilities burning coal, their industrial and residential customers, and the coal industry. AECDP project work will supply the information needed by utilities to respond to potential HAPs regulations in a timely, cost-effective, enviromnentally-sound manner which supports the continued use of the Nation's abundant reserves of coal, such as those in the State of Ohio. The development work is being carried out using the 10 MW Clean Environment Development Facility wherein air toxics emissions control strategies can be developed under controlled conditions. The specific objectives of the project are to (1) measure and understand production and partitioning of air toxics species for a variety of coals, (2) optimize the air toxics removal performance of conventional flue gas cleanup systems, (3) develop advanced air toxics emissions control concepts, (4) develop and validate air toxics emissions measurement and monitoring techniques, and (5) establish a comprehensive, self-consistent air toxics data library. This project is supported by the Department of Energy, the Ohio Coal Development Office within the Ohio Department of Development and Babcock ampersand Wilcox. A comprehensive assessment of HAP emissions from coal-fired electric utility boilers sponsored by the Department of Energy and the Electric Power Research Institute concluded that with the exception of
-
Effect of ultrasound irradiation on the production of nHAp/MWCNT nanocomposites
Energy Technology Data Exchange (ETDEWEB)
Lobo, Anderson O., E-mail: aolobo@univap.br [Laboratory of Biomedical Nanotechnology, Development Research Institute (IP and D), Universidade do Vale do Paraiba (Univap), Av. ShishimaHifumi, 2911, São José dos Campos, 12244-000 SP (Brazil); Zanin, Hudson [Associated Laboratory for Sensors and Materials (LAS), National Institute for Space Research (INPE), Av. dos Astronautas 1758, São José dos Campos, 12227-010 SP (Brazil); Siqueira, Idalia A.W.B.; Leite, Nelly C.S.; Marciano, Fernanda R. [Laboratory of Biomedical Nanotechnology, Development Research Institute (IP and D), Universidade do Vale do Paraiba (Univap), Av. ShishimaHifumi, 2911, São José dos Campos, 12244-000 SP (Brazil); Corat, Evaldo J. [Associated Laboratory for Sensors and Materials (LAS), National Institute for Space Research (INPE), Av. dos Astronautas 1758, São José dos Campos, 12227-010 SP (Brazil)
2013-10-15
Large amounts of nanohydroxyapatite (nHAp)-multiwall carbon nanotube (MWCNT) nanocomposites are produced by two different aqueous precipitation methods. The ultrasonic irradiation (UI) and slow-drip addition under continuous magnetic stirring (DMS) methods were used to investigate the precipitation of nHAp acicular crystals. Calcium-nitrate, diammonium hydrogen phosphate, and ammonium hydroxide were used as precursor reagents. Superhydrophilic MWCNT were also employed. XPS analysis evidences that the functionalized MWCNTs are composed of 18 to 20 at.% of oxygen and that this property influences the nHAp formation. The high surface area of the MWCNT decreases the mean free path of ions, favoring the nHAp formation assisted by UI. The crystallinity was evaluated using the Scherrer equation. Semi-qualitative energy dispersive spectroscopy (EDS) analysis showed that the main components of HAp powders were calcium and phosphorus in the ratio Ca/P around of 1.67. Bioactivity properties of the nHAp/MWCNT-UI nanocomposites could be evaluated after 14 days soaking in simulated body fluid medium. Scanning electron microscopy, EDS, Fourier transform infrared attenuated total reflection spectroscopy, and X-ray diffraction techniques proved that the apatites formed on the surface and to points that the nHAp/MWCNT-UI have potential biological applications. - Highlights: • Nanohydroxyapatite/multiwalled carbon nanotube nanocomposites were produced via aqueous precipitation. • Two methodologies were compared, such as: dropwise and ultrasound irradiation (UI). • Analysis found strong connections between UI and the crystallization process.
-
iHAP – integrated haplotype analysis pipeline for characterizing the haplotype structure of genes
Directory of Open Access Journals (Sweden)
Lim Yun Ping
2006-12-01
Full Text Available Abstract Background The advent of genotype data from large-scale efforts that catalog the genetic variants of different populations have given rise to new avenues for multifactorial disease association studies. Recent work shows that genotype data from the International HapMap Project have a high degree of transferability to the wider population. This implies that the design of genotyping studies on local populations may be facilitated through inferences drawn from information contained in HapMap populations. Results To facilitate analysis of HapMap data for characterizing the haplotype structure of genes or any chromosomal regions, we have developed an integrated web-based resource, iHAP. In addition to incorporating genotype and haplotype data from the International HapMap Project and gene information from the UCSC Genome Browser Database, iHAP also provides capabilities for inferring haplotype blocks and selecting tag SNPs that are representative of haplotype patterns. These include block partitioning algorithms, block definitions, tag SNP definitions, as well as SNPs to be "force included" as tags. Based on the parameters defined at the input stage, iHAP performs on-the-fly analysis and displays the result graphically as a webpage. To facilitate analysis, intermediate and final result files can be downloaded. Conclusion The iHAP resource, available at http://ihap.bii.a-star.edu.sg, provides a convenient yet flexible approach for the user community to analyze HapMap data and identify candidate targets for genotyping studies.
-
24 CFR 983.206 - HAP contract amendments (to add or substitute contract units).
2010-04-01
... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false HAP contract amendments (to add or... Contract § 983.206 HAP contract amendments (to add or substitute contract units). (a) Amendment to substitute contract units. At the discretion of the PHA and subject to all PBV requirements, the HAP contract...
-
Deletion of HAPS_2096 Increases Sensitivity to Cecropin B in Haemophilus parasuis.
Chen, Fanjie; Hu, Han; Li, Zhonghua; Huang, Jiacheng; Cai, Xuwang; Wang, Chunmei; He, Qigai; Cao, Jiyue
2015-01-01
Cecropin B (CB) is a very effective natural antimicrobial peptide that has shown great potential for future antimicrobial drug development. HAPS_2096 is a Haemophilus parasuis gene that encodes the periplasmic substrate-binding protein of an ATP-binding cassette-type amino acid transporter. In this research, we constructed and verified an HAPS_2096 deletion mutant and a complementary HAPS_2096 mutant of H. parasuis JS0135. A bactericidal assay revealed that the HAPS_2096 deletion mutant was significantly more sensitive than the wild-type strain to 0.25-0.5 µg/ml CB. However, the gene complementation alleviated the CB sensitivity of the mutant. Immunoelectron microscopy observation following a 30-min treatment with a sublethal concentration of CB (0.25 μg/ml) revealed more extensive morphological damage in the mutant strain than in the wild-type strain. Hence, our results suggest that the HAPS_2096 gene contributes to H. parasuis resistance to CB. © 2015 S. Karger AG, Basel.
-
Control of mercury emissions from coal-fired boilers
Energy Technology Data Exchange (ETDEWEB)
Huang, H.S.; Livengood, C.D.
1992-09-01
This project at Argonne is designed to investigate new concepts leading to advanced control technologies for fossil-energy systems. The objective of this new task on air toxics control is to develop new or improved, cost-effective control technology for the abatement of emissions of hazardous air pollutants (HAPs) from fossil-fuel combustion plants and to evaluate the possible effects of any captured species on waste disposal. The HAPs to be investigated initially in this task include mercury and arsenic compounds.
-
Control of mercury emissions from coal-fired boilers
Energy Technology Data Exchange (ETDEWEB)
Huang, H.S.; Livengood, C.D.
1992-01-01
This project at Argonne is designed to investigate new concepts leading to advanced control technologies for fossil-energy systems. The objective of this new task on air toxics control is to develop new or improved, cost-effective control technology for the abatement of emissions of hazardous air pollutants (HAPs) from fossil-fuel combustion plants and to evaluate the possible effects of any captured species on waste disposal. The HAPs to be investigated initially in this task include mercury and arsenic compounds.
-
Ammonia emission factors for UK agriculture
Misselbrook, T. H.; Van Der Weerden, T. J.; Pain, B. F.; Jarvis, S. C.; Chambers, B. J.; Smith, K. A.; Phillips, V. R.; Demmers, T. G. M.
Ammonia (NH 3) emission inventories are required for modelling atmospheric NH 3 transport and estimating downwind deposition. A recent inventory for UK agriculture, estimating emission as 197 kt NH 3-N yr -1, was constructed using 1993 statistical and census data for the UK. This paper describes the derivation of the UK-based emission factors used in the calculation of that emission for a range of livestock classes, farm practices and fertiliser applications to agricultural land. Some emission factors have been updated where more recent information has become available. Some of the largest emission factors derived for each farming practice include 16.9 g NH 3-N dairy cow -1 d -1 for grazing, 148.8 g NH 3-N liveweight unit -1 yr -1 for housed broilers and 4.8 g NH 3-N m -2 d -1 for storage of solid pig and poultry waste as manure heaps. Emissions for land spreading of all livestock waste were 59% of the total ammoniacal nitrogen (TAN) applied as a high dry matter content slurry and 76% of TAN applied as farm yard manure. An updated estimate of emission from UK agriculture, using updated emission factors together with 1997 statistical and census data, is presented, giving a total of 226 kt NH 3-N per year.
-
Navigation and Positioning System Using High Altitude Platforms Systems (HAPS)
Tsujii, Toshiaki; Harigae, Masatoshi; Harada, Masashi
Recently, some countries have begun conducting feasibility studies and R&D projects on High Altitude Platform Systems (HAPS). Japan has been investigating the use of an airship system that will function as a stratospheric platform for applications such as environmental monitoring, communications and broadcasting. If pseudolites were mounted on the airships, their GPS-like signals would be stable augmentations that would improve the accuracy, availability, and integrity of GPS-based positioning systems. Also, the sufficient number of HAPS can function as a positioning system independent of GPS. In this paper, a system design of the HAPS-based positioning system and its positioning error analyses are described.
-
Reducing VOC Press Emission from OSB Manufacturing; FINAL
International Nuclear Information System (INIS)
Gary D, McGinnis; Laura S, WIlliams; Amy E, Monte; Jagdish Rughani; Brett A, Niemi; Thomas M, Flicker
2001-01-01
Current regulations require industry to meet air emission standards with regard to particulates, volatile organic compounds (VOCs), hazardous air pollutants (HAPs) and other gases. One of many industries that will be affected by the new regulations is the wood composites industry. This industry generates VOCs, HAPs, and particulates mainly during the drying and pressing of wood. Current air treatment technologies for the industry are expensive to install and operate. As regulations become more stringent, treatment technologies will need to become more efficient and cost effective. The overall objective of this study is to evaluate the use of process conditions and chemical additives to reduce VOC/HAPs in air emitted from presses and dryers during the production of oriented strand board
-
Health effects of soy-biodiesel emissions: mutagenicity-emission factors.
Mutlu, Esra; Warren, Sarah H; Matthews, Peggy P; King, Charly; Walsh, Leon; Kligerman, Andrew D; Schmid, Judith E; Janek, Daniel; Kooter, Ingeborg M; Linak, William P; Gilmour, M Ian; DeMarini, David M
2015-01-01
Soy biodiesel is the predominant biodiesel fuel used in the USA, but only a few, frequently conflicting studies have examined the potential health effects of its emissions. We combusted petroleum diesel (B0) and fuels with increasing percentages of soy methyl esters (B20, B50 and B100) and determined the mutagenicity-emission factors expressed as revertants/megajoule of thermal energy consumed (rev/MJ(th)). We combusted each fuel in replicate in a small (4.3-kW) diesel engine without emission controls at a constant load, extracted organics from the particles with dichloromethane, determined the percentage of extractable organic material (EOM), and evaluated these extracts for mutagenicity in 16 strains/S9 combinations of Salmonella. Mutagenic potencies of the EOM did not differ significantly between replicate experiments for B0 and B100 but did for B20 and B50. B0 had the highest rev/MJ(th), and those of B20 and B100 were 50% and ∼85% lower, respectively, in strains that detect mutagenicity due to polycyclic aromatic hydrocarbons (PAHs), nitroarenes, aromatic amines or oxidative mutagens. For all strains, the rev/MJ(th) decreased with increasing biodiesel in the fuel. The emission factor for the 16 EPA Priority PAHs correlated strongly (r(2 )= 0.69) with the mutagenicity-emission factor in strain TA100 + S9, which detects PAHs. Under a constant load, soy-biodiesel emissions were 50-85% less mutagenic than those of petroleum diesel. Without additional emission controls, petroleum and biodiesel fuels had mutagenicity-emission factors between those of large utility-scale combustors (e.g. natural gas, coal, or oil) and inefficient open-burning (e.g. residential wood fireplaces).
-
Enhanced Control of Mercury and other HAPs by Innovative Modifications to Wet FGD Processes
International Nuclear Information System (INIS)
Hargrove, O.W.; Carey, T.R.; Richardson, C.F.; Skarupa, R.C.; Meserole, F.B.; Rhudy, R.G.; Brown, Thomas D.
1997-01-01
The overall objective of this project was to learn more about controlling emissions of hazardous air pollutants (HAPs) from coal-fired power plants that are equipped with wet flue gas desulfurization (FGD) systems. The project was included by FETC as a Phase I project in its Mega-PRDA program. Phase I of this project focused on three research areas. These areas in order of priority were: (1) Catalytic oxidation of vapor-phase elemental mercury; (2) Enhanced particulate-phase HAPs removal by electrostatic charging of liquid droplets; and (3) Enhanced mercury removal by addition of additives to FGD process liquor. Mercury can exist in two forms in utility flue gas--as elemental mercury and as oxidized mercury (predominant form believed to be HgCl 2 ). Previous test results have shown that wet scrubbers effectively remove the oxidized mercury from the gas but are ineffective in removing elemental mercury. Recent improvements in mercury speciation techniques confirm this finding. Catalytic oxidation of vapor-phase elemental mercury is of interest in cases where a wet scrubber exists or is planned for SO 2 control. If a loW--cost process could be developed to oxidize all of the elemental mercury in the flue gas, then the maximum achievable mercury removal across the existing or planned wet scrubber would increase. Other approaches for improving control of HAPs included a method for improving particulate removal across the FGD process and the use of additives to increase mercury solubility. This paper discusses results related only to catalytic oxidation of elemental mercury
-
Geographical affinities of the HapMap samples.
Directory of Open Access Journals (Sweden)
Miao He
Full Text Available The HapMap samples were collected for medical-genetic studies, but are also widely used in population-genetic and evolutionary investigations. Yet the ascertainment of the samples differs from most population-genetic studies which collect individuals who live in the same local region as their ancestors. What effects could this non-standard ascertainment have on the interpretation of HapMap results?We compared the HapMap samples with more conventionally-ascertained samples used in population- and forensic-genetic studies, including the HGDP-CEPH panel, making use of published genome-wide autosomal SNP data and Y-STR haplotypes, as well as producing new Y-STR data. We found that the HapMap samples were representative of their broad geographical regions of ancestry according to all tests applied. The YRI and JPT were indistinguishable from independent samples of Yoruba and Japanese in all ways investigated. However, both the CHB and the CEU were distinguishable from all other HGDP-CEPH populations with autosomal markers, and both showed Y-STR similarities to unusually large numbers of populations, perhaps reflecting their admixed origins.The CHB and JPT are readily distinguished from one another with both autosomal and Y-chromosomal markers, and results obtained after combining them into a single sample should be interpreted with caution. The CEU are better described as being of Western European ancestry than of Northern European ancestry as often reported. Both the CHB and CEU show subtle but detectable signs of admixture. Thus the YRI and JPT samples are well-suited to standard population-genetic studies, but the CHB and CEU less so.
-
40 CFR Table 5 to Subpart Vvvvvv... - Emission Limits and Compliance Requirements for Storage Tanks
2010-07-01
... based on either total organic HAP or TOC;ii. Comply with the management practice inspection requirements... maintenance of the control device, as specified in § 63.11497(b). c. Reduce total HAP emissions by operating... requirements do not apply during periods of planned routine maintenance of the flare, as specified in § 63...
-
Thompson, Kyle J; Nazari, Shayan S; Jacobs, W Carl; Grahame, Nicholas J; McKillop, Iain H
2017-11-01
This study sought to compare mice bred to preferentially consume high amounts of alcohol (crossed-high alcohol preferring, cHAP) to c57BL/6 (C57) mice using a chronic-binge ethanol ingestion model to induce alcoholic liver disease (ALD). Male C57 and cHAP mice were randomized to a Lieber-DeCarli control (LDC) diet, Lieber-DeCarli 5% (v/v) ethanol (LDE) diet or free-choice between 10% (v/v) ethanol in drinking water (EtOH-DW) and DW. After 4 weeks mice were gavaged with either 9 g/kg maltose-dextrin (LDC+MD) or 5 g/kg EtOH (LDE+Binge, EtOH-DW+Binge). Nine hours later tissue and serum were collected and analyzed. cHAP mice on EtOH-DW consumed significantly more ethanol than cHAP or C57 mice maintained on LDE. However, cHAP and C57 mice on the LDE+Binge regiment had greater hepatosteatosis and overall degree of liver injury compared to EtOH-DW+Binge. Changes in pro-inflammatory gene expression was more pronounced in cHAP mice than C57 mice. Analysis of liver enzymes revealed a robust induction of CYP2E1 in C57 and cHAP mice maintained on EtOH-DW+Binge or LDE+Binge. However, while C57 mice exhibited higher basal hepatic glutathione than cHAP mice, these mice appeared more susceptible to oxidative stress following LDE+Binge than cHAP counterparts. Despite cHAP mice consuming more total ethanol prior to gavage when maintained on EtOH-DW, LDE followed by gavage created a more severe model of ALD in both C57 and cHAP mice. These data suggest factors other than total amount of alcohol consumed affect degree of ALD development in the chronic-binge model in cHAP mice. cHAP mice voluntarily consume high amounts of ethanol and exhibited hepatic injury when subject to chronic-binge ethanol feeding with the Lieber-DeCarli diet. However, hepatic injury was reduced in cHAP mice in a chronic-binge model following voluntary high ethanol consumption in drinking water. © The Author 2017. Medical Council on Alcohol and Oxford University Press. All rights reserved.
-
HAPS Gateway Link in the 5850-7075 MHz and Coexistence with Fixed Satellite Service
Directory of Open Access Journals (Sweden)
M. Ahmed
2013-09-01
Full Text Available Gateway link is essential to connect HAPS platform to terrestrial based networks. This crucial link is incorporated in HAPS fixed service spectrum allocation in considerably high frequencies, renders the link for more attenuations by atmospheric gases, and rain effects, especially when the regional climate is not favorable. However, under the agenda item 1.20 of World Radio Conference-2012 (WRC-12 new HAPS allocation in the 5850-7075 MHz band is proposed. Although, spectrum features are incomparably reliable, on the contrary, Fixed Satellite Service (FSS uplink transmissions will have signal levels much higher than those in HAPS systems and have the potential for causing interference at the HAPS gateway receiver. In this article a key aspect of co-channel interference phenomena is investigated to facilitate optimum frequency sharing in the band in question. By proposing mitigation techniques and statistical method this generic prediction model enhances the capability of the HAPS spectrum sharing and provides flexibility in spectrum planning for different fixed services.
-
Emissions of organic hazardous air pollutants during Chinese coal combustion
Energy Technology Data Exchange (ETDEWEB)
Yan, R.; Zhu, H.J.; Zheng, C.G.; Xu, M.H. [Environmental Technology Institute, Singapore (Singapore). Innovative Center
2002-05-01
The emissions of organic hazardous air pollutants (HAPs) during the combustion of several typical Chinese coals were investigated. First, the distribution of four types of HAP, i.e., aliphatics, cyclic hydrocarbons, monoaromatic compounds and PAHs, in the CH{sub 2}C{sub l2} extracts of six Chinese coals were studied and the influences of the extractive times and coal varieties were also evaluated. Second, the partitioning of these HAPs in the flue gas during coal combustion in a small-scale reactor were investigated, depending on oven temperatures (500, 600, 700, 800, 900{sup o}C) and coal varieties. The behaviors of HAP in the combustion flue gas were compared with those in the CH{sub 2}, Cl{sub 2}, extracts. Finally, combustion was conducted at given conditions in two laboratory-scale reactors: a fluidized bed and a fixed bed. Two coals (Shengmu bituminous coal and Xunhuan anthracite coal) and one coke were considered. The HAP partitioning both in flue gases and in ashes were evaluated and compared between the two combustors.
-
Yang, Zhangmei; Fang, Zhanqiang; Tsang, Pokeung Eric; Fang, Jianzhang; Zhao, Dongye
2016-11-01
In this study, a kind of biochar-supported nano-hydroxyapatite (nHAP@BC) material was used in in-situ remediation of lead-contaminated soil. Column experiments were performed to compare the mobility of nHAP@BC and Bare-nHAP. The immobilization, accumulation and toxic effects of Pb in the after-amended soil were assessed by the in vitro toxicity tests and pot experiments. The column experiments showed a significant improvement in the mobility of nHAP@BC. The immobilization rate of Pb in the soil was 74.8% after nHAP@BC remediation. Sequential extraction procedures revealed that the residual fraction of Pb increased by 66.6% after nHAP@BC remediation, which greatly reduced the bioavailability of Pb in the soil. In addition, pot experiments indicated that nHAP@BC could effectively reduce the upward translocation capacity of Pb in a soil-plant system. The concentration of Pb in the aerial part of the cabbage mustard was 0.1 mg/kg, which is lower than the tolerance limit (0.3 mg/kg). nHAP@BC can remediate Pb-contaminated soil effectively, which can restore soil quality for planting. Copyright © 2016 Elsevier Ltd. All rights reserved.
-
40 CFR 63.4890 - What emission limits must I meet?
2010-07-01
... organic HAP-free coating technology can be used on the metal furniture components. The request must be... Standards for Hazardous Air Pollutants: Surface Coating of Metal Furniture Emission Limitations § 63.4890... emission limit for specific metal furniture components or type of components for which you believe the...
-
In vitro and in vivo tests of PLA/d-HAp nanocomposite
Thom Nguyen, Thi; Hoang, Thai; Mao Can, Van; Son Ho, Anh; Hai Nguyen, Song; Thu Trang Nguyen, Thi; Pham, Thi Nam; Phuong Nguyen, Thu; Le Hien Nguyen, Thi; Thanh Dinh Thi, Mai
2017-12-01
The bioactivity of the PLA/d-HAp nanocomposite with 30 wt.% d-HAp was evaluated by in vitro tests and indicated that after 7 immersion days in SBF solution, PLA amorphous part was hydrolyzed and PLA crystal part was remained. The formation of apatite on the surface of the material was observed. The in vivo test results of PLA/d-HAp nanocomposite (70/30 wt/wt) on femur of dogs displayed that 3 months after grafting, the materials did not induce any osteitis, osteomyelitis or structural abnormalities. The histological and x-ray image demonstrated a growth of the bone into the material area, while osteitis and osteomyelitis were not observed.
-
40 CFR 63.5390 - How do I measure the HAP content of a finish?
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true How do I measure the HAP content of a... Initial Compliance Requirements § 63.5390 How do I measure the HAP content of a finish? (a) To determine the HAP content of a finish, the reference method is EPA Method 311 of appendix A of 40 CFR part 63...
-
Estimation of vehicular emissions using dynamic emission factors: A case study of Delhi, India
Mishra, Dhirendra; Goyal, P.
2014-12-01
The estimation of vehicular emissions depends mainly on the values of emission factors, which are used for the development of a comprehensive emission inventory of vehicles. In this study the variations of emission factors as well as the emission rates have been studied in Delhi. The implementation of compressed natural gas (CNG), in the diesel and petrol, public vehicles in the year 2001 has changed the complete air quality scenario of Delhi. The dynamic emission factors of criteria pollutants viz. carbon monoxide (CO), nitrogen oxide (NOx) and particulate matter (PM10) for all types of vehicles have been developed after, which are based on the several factors such as regulated emission limits, number of vehicle deterioration, vehicle increment, vehicle age etc. These emission factors are found to be decreased continuously throughout the study years 2003-2012. The International Vehicle Emissions (IVE) model is used to estimate the emissions of criteria pollutants by utilizing a dataset available from field observations at different traffic intersections in Delhi. Thus the vehicular emissions, based on dynamic emission factors have been estimated for the years 2003-2012, which are found to be comparable with the monitored concentrations at different locations in Delhi. It is noticed that the total emissions of CO, NOx, and PM10 are increased by 45.63%, 68.88% and 17.92%, respectively up to the year 2012 and the emissions of NOx and PM10 are grown continuously with an annual average growth rate of 5.4% and 1.7% respectively.
-
SimHap GUI: an intuitive graphical user interface for genetic association analysis.
Carter, Kim W; McCaskie, Pamela A; Palmer, Lyle J
2008-12-25
Researchers wishing to conduct genetic association analysis involving single nucleotide polymorphisms (SNPs) or haplotypes are often confronted with the lack of user-friendly graphical analysis tools, requiring sophisticated statistical and informatics expertise to perform relatively straightforward tasks. Tools, such as the SimHap package for the R statistics language, provide the necessary statistical operations to conduct sophisticated genetic analysis, but lacks a graphical user interface that allows anyone but a professional statistician to effectively utilise the tool. We have developed SimHap GUI, a cross-platform integrated graphical analysis tool for conducting epidemiological, single SNP and haplotype-based association analysis. SimHap GUI features a novel workflow interface that guides the user through each logical step of the analysis process, making it accessible to both novice and advanced users. This tool provides a seamless interface to the SimHap R package, while providing enhanced functionality such as sophisticated data checking, automated data conversion, and real-time estimations of haplotype simulation progress. SimHap GUI provides a novel, easy-to-use, cross-platform solution for conducting a range of genetic and non-genetic association analyses. This provides a free alternative to commercial statistics packages that is specifically designed for genetic association analysis.
-
[Study on the anti-NTHi infection of Hap recombinant protein in vivo].
Li, Wan-yi; Wang, Bao-ning; Zuo, Feng-qiong; Zeng, Wei; Feng, Feng; Kuang, Yu; Jiang, Zhong-hua; Li, Ming-yuan
2010-07-01
To observe the immune effect of Hap recombinant protein on murine model of bronchopneumonia infected with NTHi, and explore the mechanism about the anti-NTHi infection. The C57BL/6 mice intranasally immunized with purified Hap recombinant protein and CT-B were challenged by NTHi encased in agar beads. The immunifaction of anti-infection was observed through encocyte counting of BALF, bacteria detection of lung and the pathologyical change of lung tissue. In the challenge with NTHi experiment, the inflammatory exudation of the infected murine and pathological change of lung tissue was relieved by combined immunization of Hap recombinant protein and CT-B, and quantity of NTHi in lung of the infected murine was reduced obviously. The Hap recombinant protein also had good ability of anti-NTHi infection in the murine model of NTHi bronchopneumonia. This study could offer the oretical and experimental basis for development of new vaccine against NTHi.
-
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Default Organic HAP Mass Fraction for... 63—Default Organic HAP Mass Fraction for Petroleum Solvent Groups a You may use the mass fraction... formulation data: Solvent type Averageorganic HAP mass fraction Typical organic HAP, percent by mass Aliphatic...
-
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Default Organic HAP Mass Fraction for... 63—Default Organic HAP Mass Fraction for Solvents and Solvent Blends You may use the mass fraction... formulation data. Solvent/solvent blend CAS. No. Averageorganic HAP mass fraction Typical organic HAP, percent...
-
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Default Organic HAP Mass Fraction for... Organic HAP Mass Fraction for Solvents and Solvent Blends You may use the mass fraction values in the... Solvent/solvent blend CAS. No. Averageorganic HAP mass fraction Typical organic HAP, percent by mass 1...
-
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Default Organic HAP Mass Fraction for... Part 63—Default Organic HAP Mass Fraction for Petroleum Solvent Groups a You may use the mass fraction... formulation data. Solvent type Average organic HAP mass fraction Typical organic HAP, percent by mass...
-
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Default Organic HAP Mass Fraction for... Organic HAP Mass Fraction for Petroleum Solvent Groups a You may use the mass fraction values in the.... Solvent type Averageorganic HAP mass fraction Typical organic HAP, percent by mass Aliphatic b 0.03 1...
-
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Default Organic HAP Mass Fraction for... Organic HAP Mass Fraction for Petroleum Solvent Groups a You may use the mass fraction values in the... Solvent type Averageorganic HAP mass fraction Typical organic HAP, percent by mass Aliphatic b 0.03 1...
-
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Default Organic HAP Mass Fraction for... HAP Mass Fraction for Solvents and Solvent Blends You may use the mass fraction values in the.... Solvent/solvent blend CAS. No. Average organic HAP mass fraction Typical organic HAP, percent by mass 1...
-
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Default Organic HAP Mass Fraction for... HAP Mass Fraction for Petroleum Solvent Groups a You may use the mass fraction values in the following... type Average organic HAP mass fraction Typical organic HAP, percent by mass Aliphatic b 0.03 1% xylene...
-
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Default Organic HAP Mass Fraction for... Large Appliances Pt. 63, Subpt. NNNN, Table 3 Table 3 to Subpart NNNN of Part 63—Default Organic HAP.../solvent blend CAS. No. Average organic HAP mass fraction Typical organic HAP, percent by mass 1. Toluene...
-
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Default Organic HAP Mass Fraction for... Metal Furniture Pt. 63, Subpt. RRRR, Table 3 Table 3 to Subpart RRRR of Part 63—Default Organic HAP Mass... blend CAS. No. Average organic HAP mass fraction Typical organic HAP, percent by mass 1. Toluene 108-88...
-
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Default Organic HAP Mass Fraction for... Metal Cans Pt. 63, Subpt. KKKK, Table 6 Table 6 to Subpart KKKK of Part 63—Default Organic HAP Mass... blend CAS. No. Averageorganic HAP mass fraction Typical organic HAP, percent by mass 1. Toluene 108-88-3...
-
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Default Organic HAP Mass Fraction for... Metal Furniture Pt. 63, Subpt. RRRR, Table 4 Table 4 to Subpart RRRR of Part 63—Default Organic HAP Mass... Average organic HAP mass fraction Typical organic percent HAP, by mass Aliphatic 2 0.03 1% Xylene, 1...
-
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Default Organic HAP Mass Fraction for... Large Appliances Pt. 63, Subpt. NNNN, Table 4 Table 4 to Subpart NNNN of Part 63—Default Organic HAP... type Average organic HAP mass fraction Typical organic HAP, percent by mass Aliphatic b 0.03 1% Xylene...
-
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Default Organic HAP Mass Fraction for... Metal Cans Pt. 63, Subpt. KKKK, Table 7 Table 7 to Subpart KKKK of Part 63—Default Organic HAP Mass... Averageorganic HAP mass fraction Typicalorganic HAP, percent by mass Aliphatic b 0.03 1% Xylene, 1% toluene, and...
-
International Nuclear Information System (INIS)
Santos, C.; Piedade, C.; Uggowitzer, P.J.; Montemor, M.F.; Carmezim, M.J.
2015-01-01
Graphical abstract: - Highlights: • A GO/HapNP thin coating was applied on XHP-Mg using a parallel nano-assembling route. • The coating surface wettability can be controlled by adding HapNP and/or GO. • Nanostructured GO/HapNP/phosphate coating promotes the apatite mineralization. • Critical properties, including degradation on SBF, of the coating were studied. - Abstract: This work reports the one-step fabrication of a novel coating on ultra high purity magnesium using a parallel nano assembling process. The multifunctional biodegradable surface was obtained by adding hydroxyapatite nanoparticles (HapNP) plus graphene oxide (GO). The coating was characterized by scanning electron microscope (SEM), transmission electron microscope (TEM), X-ray diffractometer (XRD), micro-Raman spectroscopy. The thin phosphate coating (thickness of 1 μm) reveals a uniform coverage with cypress like structures. The incorporation of HapNP and GO promotes the hydrophilic behavior of the coating surface. The results revealed that the proposed coating can be used to tailor the surface properties such as wettability by adjusting the contents of HapNP and GO. The in vitro degradation rate of the coated magnesium suggests that the presence of HapNP and GO/HapNP in the phosphate coating decreased the current density compared to the single phosphate coating and uncoated magnesium. This study also reveals the HapNP/GO/phosphate coating induces apatite formation, showing suitable degradability that makes it a promising coating candidate for enhanced bone regeneration
-
Energy Technology Data Exchange (ETDEWEB)
Santos, C., E-mail: catarina.santos@estsetubal.ips.pt [EST Setúbal, DEM, Instituto Politécnico de Setúbal, Campus IPS, 2914-508 Setúbal (Portugal); CQE, Instituto Superior Técnico, Universidade de Lisboa, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); Piedade, C. [EST Setúbal, DEM, Instituto Politécnico de Setúbal, Campus IPS, 2914-508 Setúbal (Portugal); Uggowitzer, P.J. [Laboratory of Metal Physics and Technology, ETH Zurich, 8093 Zurich (Switzerland); Montemor, M.F. [CQE, Instituto Superior Técnico, Universidade de Lisboa, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); Carmezim, M.J. [EST Setúbal, DEM, Instituto Politécnico de Setúbal, Campus IPS, 2914-508 Setúbal (Portugal); CQE, Instituto Superior Técnico, Universidade de Lisboa, Av. Rovisco Pais, 1049-001 Lisboa (Portugal)
2015-08-01
Graphical abstract: - Highlights: • A GO/HapNP thin coating was applied on XHP-Mg using a parallel nano-assembling route. • The coating surface wettability can be controlled by adding HapNP and/or GO. • Nanostructured GO/HapNP/phosphate coating promotes the apatite mineralization. • Critical properties, including degradation on SBF, of the coating were studied. - Abstract: This work reports the one-step fabrication of a novel coating on ultra high purity magnesium using a parallel nano assembling process. The multifunctional biodegradable surface was obtained by adding hydroxyapatite nanoparticles (HapNP) plus graphene oxide (GO). The coating was characterized by scanning electron microscope (SEM), transmission electron microscope (TEM), X-ray diffractometer (XRD), micro-Raman spectroscopy. The thin phosphate coating (thickness of 1 μm) reveals a uniform coverage with cypress like structures. The incorporation of HapNP and GO promotes the hydrophilic behavior of the coating surface. The results revealed that the proposed coating can be used to tailor the surface properties such as wettability by adjusting the contents of HapNP and GO. The in vitro degradation rate of the coated magnesium suggests that the presence of HapNP and GO/HapNP in the phosphate coating decreased the current density compared to the single phosphate coating and uncoated magnesium. This study also reveals the HapNP/GO/phosphate coating induces apatite formation, showing suitable degradability that makes it a promising coating candidate for enhanced bone regeneration.
-
AP-42 Emissions Factors (WebFIRE)
U.S. Environmental Protection Agency — Emissions factors have long been the fundamental tool in developing national, regional, state, and local emissions inventories for air quality management decisions...
-
40 CFR 63.1367 - Recordkeeping requirements.
2010-07-01
...), records of consumption, production, and the rolling average values of the HAP and VOC factors. (3) For... Standards for Hazardous Air Pollutants for Pesticide Active Ingredient Production § 63.1367 Recordkeeping...)(i) through (vii) of this section to document that HAP emissions or HAP loadings (for wastewater) are...
-
Oda, Saori; Yurimoto, Hiroya; Nitta, Nobuhisa; Sakai, Yasuyoshi
2016-05-01
The Hap complex of the methylotrophic yeast Candida boidinii was found to be required for methanol-regulated gene expression. In this study, we performed functional characterization of CbHap3p, one of the Hap complex components in C. boidinii. Sequence alignment of Hap3 proteins revealed the presence of a unique extended C-terminal region, which is not present in Hap3p from Saccharomyces cerevisiae (ScHap3p), but is found in Hap3p proteins of methylotrophic yeasts. Deletion of the C-terminal region of CbHap3p (Δ256-292 or Δ107-237) diminished activation of methanol-regulated genes and abolished the ability to grow on methanol, but did not affect nuclear localization or DNA-binding ability. However, deletion of the N-terminal region of CbHap3p (Δ1-20) led to not only a growth defect on methanol and a decreased level of methanol-regulated gene expression, but also impaired nuclear localization and binding to methanol-regulated gene promoters. We also revealed that CbHap3p could complement the growth defect of the Schap3Δ strain on glycerol, although ScHap3p could not complement the growth defect of a Cbhap3Δ strain on methanol. We conclude that the unique C-terminal region of CbHap3p contributes to maximum activation of methanol-regulated genes, whilst the N-terminal region is required for nuclear localization and binding to DNA.
-
Improving Dryer and Press Efficiencies Through Combustion of Hydrocarbon Emissions
Energy Technology Data Exchange (ETDEWEB)
Sujit Banerjee
2005-10-31
Emission control devices on dryers and presses have been legislated into the industry, and are now an integral part of the drying system. These devices consume large quantities of natural gas and electricity and down-sizing or eliminating them will provide major energy savings. The principal strategy taken here focuses on developing process changes that should minimize (and in some cases eliminate) the need for controls. A second approach is to develop lower-cost control options. It has been shown in laboratory and full-scale work that Hazardous Air Pollutants (HAPs) emerge mainly at the end of the press cycle for particleboard, and, by extension, to other prod-ucts. Hence, only the air associated with this point of the cycle need be captured and treated. A model for estimating terpene emissions in the various zones of veneer dryers has been developed. This should allow the emissions to be concentrated in some zones and minimized in others, so that some of the air could be directly released without controls. Low-cost catalysts have been developed for controlling HAPs from dryers and presses. Catalysts conventionally used for regenerative catalytic oxidizers can be used at much lower temperatures for treating press emissions. Fluidized wood ash is an especially inexpensive mate-rial for efficiently reducing formaldehyde in dryer emissions. A heat transfer model for estimating pinene emissions from hot-pressing strand for the manufacture of flakeboard has been constructed from first principles and validated. The model shows that most of the emissions originate from the 1-mm layer of wood adjoining the platen surface. Hence, a simple control option is to surface a softwood mat with a layer of hardwood prior to pressing. Fines release a disproportionate large quantity of HAPs, and it has been shown both theo-retically and in full-scale work that particles smaller than 400 ÃÂõm are principally responsible. Georgia-Pacific is considering green
-
40 CFR Table 6 to Subpart Vvvv of... - Default Organic HAP Contents of Petroleum Solvent Groups
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Default Organic HAP Contents of... Manufacturing Pt. 63, Subpt. VVVV, Table 6 Table 6 to Subpart VVVV of Part 63—Default Organic HAP Contents of Petroleum Solvent Groups As specified in § 63.5758(a)(6), when detailed organic HAP content data for solvent...
-
40 CFR Table 2 to Subpart II of... - Volatile Organic HAP (VOHAP) Limits for Marine Coatings
2010-07-01
... 40 Protection of Environment 10 2010-07-01 2010-07-01 false Volatile Organic HAP (VOHAP) Limits... (Surface Coating) Pt. 63, Subpt. II, Table 2 Table 2 to Subpart II of Part 63—Volatile Organic HAP (VOHAP...) through (4). b VOC (including exempt compounds listed as HAP) shall be used as a surrogate for VOHAP for...
-
Kim, Gyeong-Man; Asran, Ashraf Sh; Michler, Georg H; Simon, Paul; Kim, Jeong-Sook
2008-12-01
Based on the biomimetic approaches the present work describes a straightforward technique to mimic not only the architecture (the morphology) but also the chemistry (the composition) of the lowest level of the hierarchical organization of bone. This technique uses an electrospinning (ES) process with polyvinyl alcohol (PVA) and hydroxyapatite (HAp) nanoparticles. To determine morphology, crystalline structures and thermal properties of the resulting electrospun fibers with the pure PVA and PVA/HAp nanocomposite (NC) before electrospinning various techniques were employed, including transmission electron microscopy (TEM), high-resolution TEM (HR-TEM), scanning electron microscopy (SEM), x-ray diffraction (XRD), differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). In addition, FT-IR spectroscopy was carried out to analyze the complex structural changes upon undergoing electrospinning as well as interactions between HAp and PVA. The morphological and crystallographic investigations revealed that the rod-like HAp nanoparticles exhibit a nanoporous morphology and are embedded within the electrospun fibers. A large number of HAp nanorods are preferentially oriented parallel to the longitudinal direction of the electrospun PVA fibers, which closely resemble the naturally mineralized hard tissues of bones. Due to abundant OH groups present in PVA and HAp nanorods, they strongly interact via hydrogen bonding within the electrospun PVA/HAp NC fibers, which results in improved thermal properties. The unique physiochemical features of the electrospun PVA/HAp NC nanofibers prepared by the ES process will open up a wide variety of future applications related to hard tissue replacement and regeneration (bone and dentin), not limited to coating implants.
-
Energy Technology Data Exchange (ETDEWEB)
Kim, Gyeong-Man; Asran, Ashraf Sh; Michler, Georg H [Institute of Physics, Martin-Luther-University Halle-Wittenberg, D-06099 Halle/S (Germany); Simon, Paul [Max-Planck Institute for Chemical Physics of Solids, Noethnitzer Strasse 40, D-01187 Dresden (Germany); Kim, Jeong-Sook [Department of Dental Technology, Daegu Health College, 702-722 Daegu (Korea, Republic of)], E-mail: gyeong.kim@physik.uni-halle.de
2008-12-01
Based on the biomimetic approaches the present work describes a straightforward technique to mimic not only the architecture (the morphology) but also the chemistry (the composition) of the lowest level of the hierarchical organization of bone. This technique uses an electrospinning (ES) process with polyvinyl alcohol (PVA) and hydroxyapatite (HAp) nanoparticles. To determine morphology, crystalline structures and thermal properties of the resulting electrospun fibers with the pure PVA and PVA/HAp nanocomposite (NC) before electrospinning various techniques were employed, including transmission electron microscopy (TEM), high-resolution TEM (HR-TEM), scanning electron microscopy (SEM), x-ray diffraction (XRD), differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). In addition, FT-IR spectroscopy was carried out to analyze the complex structural changes upon undergoing electrospinning as well as interactions between HAp and PVA. The morphological and crystallographic investigations revealed that the rod-like HAp nanoparticles exhibit a nanoporous morphology and are embedded within the electrospun fibers. A large number of HAp nanorods are preferentially oriented parallel to the longitudinal direction of the electrospun PVA fibers, which closely resemble the naturally mineralized hard tissues of bones. Due to abundant OH groups present in PVA and HAp nanorods, they strongly interact via hydrogen bonding within the electrospun PVA/HAp NC fibers, which results in improved thermal properties. The unique physiochemical features of the electrospun PVA/HAp NC nanofibers prepared by the ES process will open up a wide variety of future applications related to hard tissue replacement and regeneration (bone and dentin), not limited to coating implants.
-
Directory of Open Access Journals (Sweden)
Minerva Camacho-Nuez
2017-11-01
Full Text Available Abstract Background Bovine babesiosis is a tick-borne disease caused by the protozoan parasites of the genus Babesia. In their host vector, Babesia spp. undergo sexual reproduction. Therefore, the development of sexual stages and the subsequent formation of the zygote are essential for the parasite to invade the intestinal cells of the vector tick and continue its life-cycle. HAP2/GCS1 is a protein identified in plants, protozoan parasites and other organisms that has an important role during membrane fusion in fertilization processes. The identification and characterization of HAP-2 protein in Babesia would be very significant to understand the biology of the parasite and to develop a transmission-blocking vaccine in the future. Results To isolate and sequence the hap2 gene DNA from an infected bovine with Babesia bigemina was purified. The hap2 gene was amplified, cloned and sequenced. The sequences of hap2 from four geographically different strains showed high conservation at the amino acid level, including the typical structure with a signal peptide and the HAP2/GSC domain. Antisera anti-HAP2 against the conserved extracellular region of the HAP2 amino acid sequence were obtained from rabbits. The expression of hap2 in the host and vector tissues was analyzed by using semi-quantitative RT-PCR, and the protein was examined by western blot and immunofluorescence. Based on the RT-PCR and WB results, HAP2 is expressed in both, sexual stages induced in vitro, and in infected ticks as well. We did not detect any expression in asexual erythrocytic stages of B. bigemina, relevantly anti-HAP2 specific antibodies were able to block zygotes formation in vitro. Conclusion Babesia bigemina HAP2 is expressed only in tick-infecting stages, and specific antibodies block zygote formation. Further studies regarding the function of HAP2 during tick infection may provide new insights into the molecular mechanisms of sexual reproduction of the parasite.
-
Energy Technology Data Exchange (ETDEWEB)
González, Maykel [Dept. of Molecular Engineering of Materials, Center of Applied Physics and Advanced Technology, National Autonomous University of Mexico (CFATA-UNAM), Boulevard Juriquilla 3001, Santiago de Querétaro, Querétaro 76230 (Mexico); Merino, Ulises [Dept. of Molecular Engineering of Materials, Center of Applied Physics and Advanced Technology, National Autonomous University of Mexico (CFATA-UNAM), Boulevard Juriquilla 3001, Santiago de Querétaro, Querétaro 76230 (Mexico); University of the Valley of Mexico (UVM), Boulevard Villas del Mesón 1000, Juriquilla, Santiago de Querétaro, Querétaro 76320 (Mexico); Vargas, Susana [Dept. of Molecular Engineering of Materials, Center of Applied Physics and Advanced Technology, National Autonomous University of Mexico (CFATA-UNAM), Boulevard Juriquilla 3001, Santiago de Querétaro, Querétaro 76230 (Mexico); Quintanilla, Francisco [University of the Valley of Mexico (UVM), Boulevard Villas del Mesón 1000, Juriquilla, Santiago de Querétaro, Querétaro 76320 (Mexico); Rodríguez, Rogelio, E-mail: rogelior@unam.mx [Dept. of Molecular Engineering of Materials, Center of Applied Physics and Advanced Technology, National Autonomous University of Mexico (CFATA-UNAM), Boulevard Juriquilla 3001, Santiago de Querétaro, Querétaro 76230 (Mexico)
2016-04-01
A biocompatible hybrid porous polymer–ceramic material was synthesized to be used as a biomarker in the treatment of breast cancer. This device was equipped with the capacity to release medicaments locally in a controlled manner. The biomaterial was Hydroxyapatite(HAp)-based and had a controlled pore size and pore volume fraction. It was implemented externally using a sharp end and a pair of barbed rings placed opposite each other to prevent relative movement once implanted. The biomarker was impregnated with cis-diamine dichloride platinum (II) [Cl{sub 2}-Pt-(NH{sub 3}){sub 2}]; the rate of release was obtained using inductively coupled plasma atomic emission spectroscopy (ICP-AES), and release occurred over the course of three months. Different release profiles were obtained as a function of the pore volume fraction. The biomaterial was characterized using scanning electron microscopy (SEM) and Raman spectroscopy. - Highlights: • A novel biocompatible hybrid porous polymer–ceramic material was synthesized. • The polymer–ceramic (HAp-based) material was used to prepare a biomarker. • The biomarker was impregnated with cis-diamine dichloride platinum (II). • The rate of cisplatin release was determined using inductively coupled plasma. • The kinetics of the cisplatin release was studied varying the biomarker porosity.
-
International Nuclear Information System (INIS)
González, Maykel; Merino, Ulises; Vargas, Susana; Quintanilla, Francisco; Rodríguez, Rogelio
2016-01-01
A biocompatible hybrid porous polymer–ceramic material was synthesized to be used as a biomarker in the treatment of breast cancer. This device was equipped with the capacity to release medicaments locally in a controlled manner. The biomaterial was Hydroxyapatite(HAp)-based and had a controlled pore size and pore volume fraction. It was implemented externally using a sharp end and a pair of barbed rings placed opposite each other to prevent relative movement once implanted. The biomarker was impregnated with cis-diamine dichloride platinum (II) [Cl_2-Pt-(NH_3)_2]; the rate of release was obtained using inductively coupled plasma atomic emission spectroscopy (ICP-AES), and release occurred over the course of three months. Different release profiles were obtained as a function of the pore volume fraction. The biomaterial was characterized using scanning electron microscopy (SEM) and Raman spectroscopy. - Highlights: • A novel biocompatible hybrid porous polymer–ceramic material was synthesized. • The polymer–ceramic (HAp-based) material was used to prepare a biomarker. • The biomarker was impregnated with cis-diamine dichloride platinum (II). • The rate of cisplatin release was determined using inductively coupled plasma. • The kinetics of the cisplatin release was studied varying the biomarker porosity.
-
International Nuclear Information System (INIS)
Szpunar, C.B.
1993-01-01
The US Environmental Protection Agency (EPA) is required by the 1990 CAAA to promulgate rules for all ''major'' sources of any of these HAPs. According to the HAPs section of the new Title III, any stationary source emitting 10 tons per year (TPY) of one HAP or 25 TPY of a combination of HAPs will be considered and designated a major source. In contrast to the original National Emission Standards for Hazardous Air Pollutants (NESHAP), which were designed to protect public health to ''an ample margin of safety,'' the new Title III, in its first phase, will regulate by industrial category those sources emitting HAPs in excess of the 10/25-TPY threshold levels, regardless of health risks. The trace elements normally associated with coal mineral matter and the various compounds formed during coal combustion have the potential to produce hazardous air toxic emissions from coal-fired electric utilities. Under Title III, the EPA is required to perform certain studies, prior to any regulation of electric utilities; these studies are currently underway. Also, the US Department of Energy (DOE) maintains a vested interest in addressing those energy policy questions affecting electric utility generation, coal mining, and steel producing critical to this country's economic well-being, where balancing the costs to the producers and users of energy with the benefits of environmental protection to the workers and the general populace remains of significant concern
-
Manoj, Murugesan; Subbiah, Ramesh; Mangalaraj, Devanesan; Ponpandian, Nagamony; Viswanathan, Chinnuswamy; Park, Kwideok
2015-01-01
Morphology controlled hydroxyapatite (HAp) nanostruc‐ tures play a vital role in biomedical engineering, tissue regenerative medicine, biosensors, chemotherapeutic applications, environmental remediation, etc. The present work investigates the influence of temperature, pH and time on the growth of HAp nanostructures using a simple, cost effective and surfactant free chemical approach. The obtained HAp nanostructures were systematically investi‐ gated by analytical techniques such as XRD, FESE...
-
40 CFR Table 9 to Subpart Ggg of... - Default Biorates for Soluble HAP
2010-07-01
... 40 Protection of Environment 11 2010-07-01 2010-07-01 true Default Biorates for Soluble HAP 9 Table 9 to Subpart GGG of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... Subpart GGG of Part 63—Default Biorates for Soluble HAP Compound name Biorate (K1),L/g MLVSS-hr...
-
Santos, C.; Piedade, C.; Uggowitzer, P. J.; Montemor, M. F.; Carmezim, M. J.
2015-08-01
This work reports the one-step fabrication of a novel coating on ultra high purity magnesium using a parallel nano assembling process. The multifunctional biodegradable surface was obtained by adding hydroxyapatite nanoparticles (HapNP) plus graphene oxide (GO). The coating was characterized by scanning electron microscope (SEM), transmission electron microscope (TEM), X-ray diffractometer (XRD), micro-Raman spectroscopy. The thin phosphate coating (thickness of 1 μm) reveals a uniform coverage with cypress like structures. The incorporation of HapNP and GO promotes the hydrophilic behavior of the coating surface. The results revealed that the proposed coating can be used to tailor the surface properties such as wettability by adjusting the contents of HapNP and GO. The in vitro degradation rate of the coated magnesium suggests that the presence of HapNP and GO/HapNP in the phosphate coating decreased the current density compared to the single phosphate coating and uncoated magnesium. This study also reveals the HapNP/GO/phosphate coating induces apatite formation, showing suitable degradability that makes it a promising coating candidate for enhanced bone regeneration.
-
40 CFR Table 1 to Subpart Dd of... - List of Hazardous Air Pollutants (HAP) for Subpart DD
2010-07-01
... 40 Protection of Environment 10 2010-07-01 2010-07-01 false List of Hazardous Air Pollutants (HAP... Hazardous Air Pollutants (HAP) for Subpart DD CAS No. a Chemical name fm 305 75-07-0 Acetaldehyde 1.000 75... mixtures of compounds. b. Denotes a HAP that hydrolyzes quickly in water, but the hydrolysis products are...
-
40 CFR Table 5 to Subpart Vvvv of... - Default Organic HAP Contents of Solvents and Solvent Blends
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Default Organic HAP Contents of... Manufacturing Pt. 63, Subpt. VVVV, Table 5 Table 5 to Subpart VVVV of Part 63—Default Organic HAP Contents of Solvents and Solvent Blends As specified in § 63.5758(a)(6), when detailed organic HAP content data for...
-
Directory of Open Access Journals (Sweden)
Juan Carlos Quintana Díaz
2005-12-01
Full Text Available Se realizó un estudio clínico y radiográfico pre y posoperatorio en 4 pacientes con fracturas del suelo orbitario reparadas con hidroxiapatita HAP-200. En ninguno de los pacientes se encontró reacción adversa ante este material implantalógico y sí muy buena tolerancia y adaptabilidad, lo que nos reafirmó su alta biocompatibilidad, por lo que lo recomendamos en el tratamiento de esta afección.A pre- and postoperative clinical and X-ray study was conducted in 4 patients with orbital floor fractures repaired with HAP-200hydroxyapatite. . No adverse reaction to this material was observed in any of the patients, who showed a good tolerance and adaptability that confirmed its high biocompatibility and make it recommendable for treating this affection.
-
On December 20, 2002, the EPA proposed national emission standards for HAP emissions from lime manufacturing plants located at major source facilities (67 FR 78046). Summaries of the comments, and the EPA's responses, are presented in this BID.
-
Revised emission factors for gas engines including start/stop emissions
Energy Technology Data Exchange (ETDEWEB)
Nielsen, Malene; Boll Illerup, J.; Birr-Petersen, K.
2008-06-15
Liberalisation of the electricity market has led to Danish gas engine plants increasingly converting to the spot and regulating power markets. In order to offer regulating power, plants need to be able to start and stop the engines at the plants quickly. The liberalisation causes a considerable change of operation practice of the engines e.g. less full load operation hours /year. The project provides an inventory determining the scale of the emissions during the start and stop sequence as well as proposals for engine modifications aimed at reducing start/stop emissions. This report includes calculation of emission factors as well as an inventory of total emissions and reduction potentials. (au)
-
Wang, Kun; Tian, Hezhong; Hua, Shenbing; Zhu, Chuanyong; Gao, Jiajia; Xue, Yifeng; Hao, Jiming; Wang, Yong; Zhou, Junrui
2016-07-15
China has become the largest producer of iron and steel throughout the world since 1996. However, as an energy-and-pollution intensive manufacturing sector, a detailed comprehensive emission inventory of air pollutants for iron and steel industry of China is still not available. To obtain and better understand the temporal trends and spatial variation characteristics of typical hazardous air pollutants (HAPs) emissions from iron and steel production in China, a comprehensive emission inventory of multiple air pollutants, including size segregated particulate matter (TSP/PM10/PM2.5), gaseous pollutants (SO2, NOx, CO), heavy metals (Pb, Cd, Hg, As, Cr, Ni etc.), as well as the more dangerous PCDD/Fs, is established with the unit-based annual activity, specific dynamic emission factors for the historical period of 1978-2011, and the future potential trends till to 2050 are forecasted by using scenario analysis. Our results show that emissions of gaseous pollutants and particulate matter have experienced a gradual increase tendency since 2000, while emissions of priority-controlled heavy metals (Hg, Pb, As, Cd, Cr, and Ni) have exhibited a short-term fluctuation during the period of 1990 to 2005. With regard to the spatial distribution of HAPs emissions in base year 2011, Bohai economic circle is identified as the top emission intensity region where iron and steel smelting plants are densely built; within iron and steel industry, blast furnaces contribute the majority of PM emissions, sinter plants account for most of gaseous pollutants and the majority of PCDD/Fs, whereas steel making processes are responsible for the majority of heavy metal emissions. Moreover, comparisons of future emission trends under three scenarios indicate that advanced technologies and integrated whole process management strategies are in great need to further diminish various hazardous air pollutants from iron and steel industry in the future. Copyright © 2016 Elsevier B.V. All rights
-
2010-07-01
... Manufacturing Standards for Aluminum Recreational Boat Surface Coating Operations § 63.5752 How do I calculate... fraction of organic HAP in coating i, kilograms of organic HAP per kilogram of coating. p = number of..., activator, or additive k, kilograms per liter. Wk= mass fraction of organic HAP in thinner, activator, or...
-
Directory of Open Access Journals (Sweden)
Paul S de Vries
Full Text Available An increasing number of genome-wide association (GWA studies are now using the higher resolution 1000 Genomes Project reference panel (1000G for imputation, with the expectation that 1000G imputation will lead to the discovery of additional associated loci when compared to HapMap imputation. In order to assess the improvement of 1000G over HapMap imputation in identifying associated loci, we compared the results of GWA studies of circulating fibrinogen based on the two reference panels. Using both HapMap and 1000G imputation we performed a meta-analysis of 22 studies comprising the same 91,953 individuals. We identified six additional signals using 1000G imputation, while 29 loci were associated using both HapMap and 1000G imputation. One locus identified using HapMap imputation was not significant using 1000G imputation. The genome-wide significance threshold of 5×10-8 is based on the number of independent statistical tests using HapMap imputation, and 1000G imputation may lead to further independent tests that should be corrected for. When using a stricter Bonferroni correction for the 1000G GWA study (P-value < 2.5×10-8, the number of loci significant only using HapMap imputation increased to 4 while the number of loci significant only using 1000G decreased to 5. In conclusion, 1000G imputation enabled the identification of 20% more loci than HapMap imputation, although the advantage of 1000G imputation became less clear when a stricter Bonferroni correction was used. More generally, our results provide insights that are applicable to the implementation of other dense reference panels that are under development.
-
Hilson Adolescent Profile (HAP): Hilson Research Abstracts.
Hilson Research Inc., Kew Gardens, NY.
Abstracts and bibliographic citations are given for the following documents concerned with the use and characteristics of the Hilson Adolescent Profile (HAP): (1) "Use of the Hilson Adolescent Profile To Compare Juvenile Offenders with Junior and Senior High School Students" (R. E. Inwald and K. E. Brobst); (2) "The Effectiveness of…
-
A new series of HAPs as anti-HBV agents targeting at capsid assembly.
Yang, Xiu-yan; Xu, Xiao-qian; Guan, Hua; Wang, Li-li; Wu, Qin; Zhao, Guo-ming; Li, Song
2014-09-01
A series of novel Heteroaryldihydropyrimidines (HAPs) derivatives were designed and synthesized as potent inhibitors of HBV capsid assembly. These compounds were prepared from efforts to optimize an earlier series of HAPs, and compounds Mo1, Mo7, Mo8, Mo10, Mo12, and Mo13 demonstrated potent inhibition of HBV DNA replication at submicromolar range. Copyright © 2014. Published by Elsevier Ltd.
-
2010-07-01
... 40 Protection of Environment 11 2010-07-01 2010-07-01 true Known Organic HAP Emitted From the... HAP Emitted From the Production of Thermoplastic Products Thermoplastic product/Subcategory Organic HAP/chemical name(CAS No.) Acet-aldehyde (75-07-0) Acrylo-nitrile (107-13-1) 1,3 Buta-diene (106-99-0...
-
The chemistry and health effects of individual hazardous air pollutants (HAPS) have been studied for many years. Once released into the atmosphere, HAPS interact with hydroxyl radicals and ozone (created by photochemical processes), to produce many different products, whose toxic...
-
International Nuclear Information System (INIS)
Nik Norziehana Che Isa; Norjanah Yury; Yusairie Mohd
2011-01-01
Various concentration of deposition solutions containing CaCl 2 and NH 4 H 2 PO 4 (with Ca/P ratio equal to 1.67) were used to study the effect of deposition solution concentration on the surface morphology and structure of Hydroxyapatite (HAp) coatings. Each HAp coating was deposited onto Ti substrate by applying a constant potential of 1.5 V (vs Ag/ AgCl) at 80 degree Celsius. The formation of HAp coatings was confirmed by FTIR and XRD analyses. Various morphologies consisting of HAp nanoparticles were produced from different deposition solutions as observed by SEM. The concentration of deposition solution has significantly affected the morphology of n-HAp coatings. (author)
-
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Default Organic HAP Mass Fraction for... Organic HAP Mass Fraction for Solvents and Solvent Blends You may use the mass fraction values in the... solvent blend matches both the name and CAS number for an entry, that entry's organic HAP mass fraction...
-
Health Activities Project (HAP): Action/Reaction Module.
Buller, Dave; And Others
Contained within this Health Activities Project (HAP) learning packet are activities for children in grades 5-8. Design of the activities centers around the idea that students can control their own health and safety. Within this module are teacher and student folios describing activities in timing, improving, and practicing to improve reaction…
-
Health Activities Project (HAP), Trial Edition III.
Buller, Dave; And Others
Contained within this Health Activities Project (HAP) trial edition (set III) are a teacher information folio and numerous student activity folios which center around the idea that students in grades 5-8 can control their own health and safety. Each student folio is organized into an Overview, Health Background, Materials, Setting Up, and…
-
Xiong, Chuanhe; Yang, Degang; Xia, Fuqiang; Huo, Jinwei
2016-11-10
Xinjiang's agricultural carbon emissions showed three stages of change, i.e., continued to rise, declined and continued to rise, during 1991-2014. The agriculture belonged to the "low emissions and high efficiency" agriculture category, with a lower agricultural carbon emission intensity. By using the logarithmic mean divisia index decomposition method, agricultural carbon emissions were decomposed into an efficiency factor, a structure factor, an economy factor, and a labour factor. We divided the study period into five stages based on the changes in efficiency factor and economy factor. Xinjiang showed different agricultural carbon emission characteristics at different stages. The degree of impact on agricultural carbon emissions at these stages depended on the combined effect of planting-animal husbandry carbon intensity and agricultural labour productivity. The economy factor was the critical factor to promote the increase in agricultural carbon emissions, while the main inhibiting factor for agricultural carbon emissions was the efficiency factor. The labour factor became more and more obvious in increasing agricultural carbon emissions. Finally, we discuss policy recommendations in terms of the main factors, including the development of agricultural science and technology (S&T), the establishment of three major mechanisms and transfer of rural labour in ethnic areas.
-
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Default Organic HAP Mass Fraction for... Part 63—Default Organic HAP Mass Fraction for Solvents and Solvent Blends You may use the mass fraction.... If a solvent blend matches both the name and CAS number for an entry, that entry's organic HAP mass...
-
Channel modelling for free-space optical inter-HAP links using adaptive ARQ transmission
Parthasarathy, S.; Giggenbach, D.; Kirstädter, A.
2014-10-01
Free-space optical (FSO) communication systems have seen significant developments in recent years due to growing need for very high data rates and tap-proof communication. The operation of an FSO link is suited to diverse variety of applications such as satellites, High Altitude Platforms (HAPs), Unmanned Aerial Vehicles (UAVs), aircrafts, ground stations and other areas involving both civil and military situations. FSO communication systems face challenges due to different effects of the atmospheric channel. FSO channel primarily suffers from scintillation effects due to Index of Refraction Turbulence (IRT). In addition, acquisition and pointing becomes more difficult because of the high directivity of the transmitted beam: Miss-pointing of the transmitted beam and tracking errors at the receiver generate additional fading of the optical signal. High Altitude Platforms (HAPs) are quasi-stationary vehicles operating in the stratosphere. The slowly varying but precisely determined time-of-flight of the Inter-HAP channel adds to its characteristics. To propose a suitable ARQ scheme, proper theoretical understanding of the optical atmospheric propagation and modeling of a specific scenario FSO channel is required. In this paper, a bi-directional symmetrical Inter-HAP link has been selected and modeled. The Inter-HAP channel model is then investigated via simulations in terms of optical scintillation induced by IRT and in presence of pointing error. The performance characteristic of the model is then quantified in terms of fading statistics from which the Packet Error Probability (PEP) is calculated. Based on the PEP characteristics, we propose suitable ARQ schemes.
-
HAPs-Rx: Precombustion Removal of Hazardous Air Pollutant Precursors
Energy Technology Data Exchange (ETDEWEB)
David J. Akers; Clifford E. Raleigh
1998-03-16
CQ Inc. and its project team members--Howard University, PrepTech Inc., Fossil Fuel Sciences, the United States Geological Survey (USGS), and industry advisors--are applying mature coal cleaning and scientific principles to the new purpose of removing potentially hazardous air pollutants from coal. The team uniquely combines mineral processing, chemical engineering, and geochemical expertise. This project meets more than 11 goals of the U.S. Department of Energy (DOE), the National Energy Strategy, and the 1993 Climate Change Action Plan. During this project: (1) Equations were developed to predict the concentration of trace elements in as-mined and cleaned coals. These equations, which address both conventional and advanced cleaning processes, can be used to increase the removal of hazardous air pollutant precursors (HAPs) by existing cleaning plants and to improve the design of new cleaning plants. (2) A promising chemical method of removing mercury and other HAPs was developed. At bench-scale, mercury reductions of over 50 percent were achieved on coal that had already been cleaned by froth flotation. The processing cost of this technology is projected to be less than $3.00 per ton ($3.30 per tonne). (3) Projections were made of the average trace element concentration in cleaning plant solid waste streams from individual states. Average concentrations were found to be highly variable. (4) A significantly improved understanding of how trace elements occur in coal was gained, primarily through work at the USGS during the first systematic development of semiquantitative data for mode of occurrence. In addition, significant improvement was made in the laboratory protocol for mode of occurrence determination. (5) Team members developed a high-quality trace element washability database. For example, the poorest mass balance closure for the uncrushed size and washability data for mercury on all four coals is 8.44 percent and the best is 0.46 percent. This indicates an
-
Microstructure and mechanical properties of Mg–HAP composites
Indian Academy of Sciences (India)
Administrator
tion of load bearing capacity and suitable mechanical and metallurgical properties. ... lity as compared to β-TCP in our body fluid (Kwon et al. 2003). The HAP ... steel crucible under the protection of gas mixture contain- ing SF6 and CO2.
-
NOx and SO2 emission factors for Serbian lignite Kolubara
Directory of Open Access Journals (Sweden)
Jovanović Vladimir V.
2012-01-01
Full Text Available Emission factors are widely accepted tool for estimation of various pollutants emissions in USA and EU. Validity of emission factors is strongly related to experimental data on which they are based. This paper is a result of an effort to establish reliable NOx and SO2 emission factors for Serbian coals. The results of NOx and SO2 emissions estimations based on USA and EU emission factors from thermal power plants Nikola Tesla Obrenovac A and B utilizing the Serbian lignite Kolubara are compared with experimental data obtained during almost one decade (2000-2008 of emissions measurements. Experimental data are provided from regular annual emissions measurement along with operational parameters of the boiler and coal (lignite Kolubara ultimate and proximate analysis. Significant deviations of estimated from experimental data were observed for NOx, while the results for SO2 were satisfactory. Afterwards, the estimated and experimental data were plotted and linear regression between them established. Single parameter optimization was performed targeting the ideal slope of the regression line. Results of this optimization provided original NOx and SO2 emission factors for Kolubara lignite.
-
Health Activities Project (HAP): Breathing Fitness Module.
Buller, Dave; And Others
Contained within this Health Activities Project (HAP) learning packet are activities for children in grades 5-8. Design of the activities centers around the idea that students can control their own health and safety. Within this module are teacher and student folios describing four activities which involve students in learning how to measure their…
-
Health Activities Project (HAP), Trial Edition II.
Buller, Dave; And Others
Contained within this Health Activities Project (HAP) trial edition (set II) are a teacher information folio and numerous student activity folios which center around the idea that students in grades 5-8 can control their own health and safety. Each student folio is organized into a Synopsis, Health Background, Materials, Setting Up, and Activities…
-
Matsushika, Akinori; Hoshino, Tamotsu
2015-12-01
The Saccharomyces cerevisiae HAP4 gene encodes a transcription activator that plays a key role in controlling the expression of genes involved in mitochondrial respiration and reductive pathways. This work examines the effect of knockout of the HAP4 gene on aerobic ethanol production in a xylose-utilizing S. cerevisiae strain. A hap4-deleted recombinant yeast strain (B42-DHAP4) showed increased maximum concentration, production rate, and yield of ethanol compared with the reference strain MA-B42, irrespective of cultivation medium (glucose, xylose, or glucose/xylose mixtures). Notably, B42-DHAP4 was capable of producing ethanol from xylose as the sole carbon source under aerobic conditions, whereas no ethanol was produced by MA-B42. Moreover, the rate of ethanol production and ethanol yield (0.44 g/g) from the detoxified hydrolysate of wood chips was markedly improved in B42-DHAP4 compared to MA-B42. Thus, the results of this study support the view that deleting HAP4 in xylose-utilizing S. cerevisiae strains represents a useful strategy in ethanol production processes.
-
Empirical Study of Decomposition of CO2 Emission Factors in China
Directory of Open Access Journals (Sweden)
Yadong Ning
2013-01-01
Full Text Available China’s CO2 emissions increase has attracted world’s attention. It is of great importance to analyze China’s CO2 emission factors to restrain the CO2 rapid growing. The CO2 emissions of industrial and residential consumption sectors in China during 1980–2010 were calculated in this paper. The expanded decomposition model of CO2 emissions was set up by adopting factor-separating method based on the basic principle of the Kaya identities. The results showed that CO2 emissions of industrial and residential consumption sectors increase year after year, and the scale effect of GDP is the most important factor affecting CO2 emissions of industrial sector. Decreasing the specific gravity of secondary industry and energy intensity is more effective than decreasing the primary industry and tertiary industry. The emissions reduction effect of structure factor is better than the efficiency factor. For residential consumption sector, CO2 emissions increase rapidly year after year, and the economy factor (the increase of wealthy degree or income is the most important factor. In order to slow down the growth of CO2 emissions, it is an important way to change the economic growth mode, and the structure factor will become a crucial factor.
-
Xiong, Chuanhe; Yang, Degang; Xia, Fuqiang; Huo, Jinwei
2016-01-01
Xinjiang’s agricultural carbon emissions showed three stages of change, i.e., continued to rise, declined and continued to rise, during 1991–2014. The agriculture belonged to the “low emissions and high efficiency” agriculture category, with a lower agricultural carbon emission intensity. By using the logarithmic mean divisia index decomposition method, agricultural carbon emissions were decomposed into an efficiency factor, a structure factor, an economy factor, and a labour factor. We divided the study period into five stages based on the changes in efficiency factor and economy factor. Xinjiang showed different agricultural carbon emission characteristics at different stages. The degree of impact on agricultural carbon emissions at these stages depended on the combined effect of planting-animal husbandry carbon intensity and agricultural labour productivity. The economy factor was the critical factor to promote the increase in agricultural carbon emissions, while the main inhibiting factor for agricultural carbon emissions was the efficiency factor. The labour factor became more and more obvious in increasing agricultural carbon emissions. Finally, we discuss policy recommendations in terms of the main factors, including the development of agricultural science and technology (S&T), the establishment of three major mechanisms and transfer of rural labour in ethnic areas. PMID:27830739
-
Development of database of real-world diesel vehicle emission factors for China.
Shen, Xianbao; Yao, Zhiliang; Zhang, Qiang; Wagner, David Vance; Huo, Hong; Zhang, Yingzhi; Zheng, Bo; He, Kebin
2015-05-01
A database of real-world diesel vehicle emission factors, based on type and technology, has been developed following tests on more than 300 diesel vehicles in China using a portable emission measurement system. The database provides better understanding of diesel vehicle emissions under actual driving conditions. We found that although new regulations have reduced real-world emission levels of diesel trucks and buses significantly for most pollutants in China, NOx emissions have been inadequately controlled by the current standards, especially for diesel buses, because of bad driving conditions in the real world. We also compared the emission factors in the database with those calculated by emission factor models and used in inventory studies. The emission factors derived from COPERT (Computer Programmer to calculate Emissions from Road Transport) and MOBILE may both underestimate real emission factors, whereas the updated COPERT and PART5 (Highway Vehicle Particulate Emission Modeling Software) models may overestimate emission factors in China. Real-world measurement results and emission factors used in recent emission inventory studies are inconsistent, which has led to inaccurate estimates of emissions from diesel trucks and buses over recent years. This suggests that emission factors derived from European or US-based models will not truly represent real-world emissions in China. Therefore, it is useful and necessary to conduct systematic real-world measurements of vehicle emissions in China in order to obtain the optimum inputs for emission inventory models. Copyright © 2015. Published by Elsevier B.V.
-
Hussein, Hala E.; Bastos, Reginaldo G.; Schneider, David A.; Johnson, Wendell C.; Adham, Fatma K.; Davis, William C.; Laughery, Jacob M.; Herndon, David R.; Alzan, Heba F.
2017-01-01
Babesia bovis, is a tick borne apicomplexan parasite responsible for important cattle losses globally. Babesia parasites have a complex life cycle including asexual replication in the mammalian host and sexual reproduction in the tick vector. Novel control strategies aimed at limiting transmission of the parasite are needed, but transmission blocking vaccine candidates remain undefined. Expression of HAP2 has been recognized as critical for the fertilization of parasites in the Babesia-related Plasmodium, and is a leading candidate for a transmission blocking vaccine against malaria. Hereby we identified the B. bovis hap2 gene and demonstrated that it is widely conserved and differentially transcribed during development within the tick midgut, but not by blood stage parasites. The hap2 gene was disrupted by transfecting B. bovis with a plasmid containing the flanking regions of the hap2 gene and the GPF-BSD gene under the control of the ef-1α-B promoter. Comparison of in vitro growth between a hap2-KO B. bovis clonal line and its parental wild type strain showed that HAP2 is not required for the development of B. bovis in erythrocytes. However, xanthurenic acid-in vitro induction experiments of sexual stages of parasites recovered after tick transmission resulted in surface expression of HAP2 exclusively in sexual stage induced parasites. In addition, hap2-KO parasites were not able to develop such sexual stages as defined both by morphology and by expression of the B. bovis sexual marker genes 6-Cys A and B. Together, the data strongly suggests that tick midgut stage differential expression of hap2 is associated with the development of B. bovis sexual forms. Overall these studies are consistent with a role of HAP2 in tick stages of the parasite and suggest that HAP2 is a potential candidate for a transmission blocking vaccine against bovine babesiosis. PMID:28985216
-
Liu, Dai-Fang; Mason, Kathryn W.; Mastri, Maria; Pazirandeh, Mehran; Cutter, David; Fink, Doran L.; St. Geme, Joseph W.; Zhu, Duzhang; Green, Bruce A.
2004-01-01
Nontypeable Haemophilus influenzae is a major causative agent of bacterial otitis media in children. H. influenzae Hap autotransporter protein is an adhesin composed of an outer membrane Hapβ region and a moiety of an extracellular internal 110-kDa passenger domain called HapS. The HapS moiety promotes adherence to human epithelial cells and extracellular matrix proteins, and it also mediates bacterial aggregation and microcolony formation. A recent work (D. L. Fink, A. Z. Buscher, B. A. Gree...
-
Air toxics evaluation for a nuclear power plant
International Nuclear Information System (INIS)
Lokey, D.; Orr, W.
1994-01-01
An emission inventory of nonradiological hazardous air pollutants (HAP) was prepared for TVA's Browns Ferry Nuclear Plant (BFN). The purpose of this effort was to determine whether BFN is a major HAP emission source. About 40 specific HAP were identified in products used at FBN. HAP emission totals from BFN were estimated at 6 T/Y, well below the major-source cutoff. Off-site waste disposal reduced gross emission estimates by about 8 percent. HAP emission evaluation by product categories showed the largest portion due to paints and coatings, followed by cleaning compounds. HAP emission breakdown by chemical species showed xylene to be the predominate HAP emitted, followed by methyl ethyl ketone
-
Greenhouse gas emission factors of purchased electricity from interconnected grids
International Nuclear Information System (INIS)
Ji, Ling; Liang, Sai; Qu, Shen; Zhang, Yanxia; Xu, Ming; Jia, Xiaoping; Jia, Yingtao; Niu, Dongxiao; Yuan, Jiahai; Hou, Yong; Wang, Haikun; Chiu, Anthony S.F.; Hu, Xiaojun
2016-01-01
Highlights: • A new accounting framework is proposed for GHG emission factors of power grids. • Three cases are used to demonstrate the proposed framework. • Comparisons with previous system boundaries approve the necessity. - Abstract: Electricity trade among power grids leads to difficulties in measuring greenhouse gas (GHG) emission factors of purchased electricity. Traditional methods assume either electricity purchased from a grid is entirely produced locally (Boundary I) or imported electricity is entirely produced by the exporting grid (Boundary II) (in fact a blend of electricity produced by many grids). Both methods ignore the fact that electricity can be indirectly traded between grids. Failing to capture such indirect electricity trade can underestimate or overestimate GHG emissions of purchased electricity in interconnected grid networks, potentially leading to incorrectly accounting for the effects of emission reduction policies involving purchased electricity. We propose a “Boundary III” framework to account for emissions both directly and indirectly caused by purchased electricity in interconnected gird networks. We use three case studies on a national grid network, an Eurasian Continent grid network, and North Europe grid network to demonstrate the proposed Boundary III emission factors. We found that the difference on GHG emissions of purchased electricity estimated using different emission factors can be considerably large. We suggest to standardize the choice of different emission factors based on how interconnected the local grid is with other grids.
-
Emission factor development for the malt beverage, wine, and distilled spirits industries
Energy Technology Data Exchange (ETDEWEB)
Lapp, T.; Shrager, B. [Midwest Research Institute, Cary, NC (United States); Safriet, D. [Environmental Protection Agency, Research Triangle Park, NC (United States)
1996-12-31
Midwest Research Institute is currently developing emission factors for inclusion in AP-42 Chapter 9, Food and Agricultural Industries. Three of the sections cover the production of malt beverages, wine, and distilled spirits. The malt beverage segment focuses on the development of ethanol emission factors for filling operations, which were recently identified as the large source of brewery ethanol emissions. The discussion includes a description of the production process and emissions factors for breweries, a history of emission factories for breweries, a description of emission testing conducted at two large breweries, and a presentation of some of the emission factors for malt beverage production. The wine industry segment focuses on emissions from the fermentation stage for red and white wines, the pomace screen and pomace press for red wines, and bottling of white wine. Emission factors are presented for ethanol emissions from each of these sources as well as other VOC emissions from the fermentation process. A discussion of the wine production process is presented. A discussion of the emission sources and available emission factors is presented for the distilled spirits industry segment. Factors are presented for the fermentation and aging stages. A process description is presented for the production of Bourbon whisky.
-
Fara, A. N. K. A.; Abdullah, H. Z.
2015-07-01
Hydroxyapatite, (HAp), Ca10(PO4)6(OH)2, is recognised as a biomaterial that is widely used for bone implant due to its chemical and structural similarity to the mineral components in human bone and enamel. The elements of HAp are primarily composed of calcium and phosphorus molar ratio of calcium to phosphorous is 1.67 capable to promote bone in-growth into prosthetic implant. Enormous amounts of by-product waste produced from fish factories generated an undesirable environmental impact. Thus, this study was conducted to obtain natural biological HAp from different types of tilapia fish bones and scales from fishery waste. Therefore, fish bones and scales can be as cheap source to produce biological HAp for medical applications. For this purpose, fish bones and scales of tilapia fish were boiled at 100°C to remove adhering meat and other impurities. Later, fish bones and scales were separated into several groups and subjected to different calcination temperatures of 800° C and 900° C for 3h respectively. Afterward, all calcined samples were crushed to form a fine powder. The XRD result revealed the presence of derived Hapfrom the samples powder and were identical with standard Hap. Thermo Gravimetric Analysis was carried out to show the thermal stability of the HAp powder from different types of fish bones and scales. SEM results show porous structure appeared in calcined samples compared to raw samples. The findings are the promising alternative to produce calcium and phosphorus from fishery wastes that beneficial to medical applications.
-
Directory of Open Access Journals (Sweden)
I. Iskandar
2014-11-01
Full Text Available Deploying WiMAX through High Altitude Platform Station (HAPS system is a new means of wireless delivery method and thus attracting much the attention in a telecommunication society. However delivering WiMAX through the terrestrial network has already been started a few years ago. Therefore, we need to look at the scenario of coexistence system both of HAPS and terrestrial in delivering WiMAX services. This paper evaluates the performance of coexistence system between cellular HAPS and terrestrial for the downlink scenario when they are transmitting WiMAX mobile 802.16e services. Our evaluation is based on the performance simulation of coexistence model using two methods. First method is a footprint exchange between the two systems.The second method is a combination of footprint exchange and HAPS footprint enhancement. The proposed methodsare then evaluated by computer simulation in terms of carrier to interference plus noise ratio (CINR performance. In general, both methods resulting performance enhancement in CINR quality compared with coexistence deployment with normal scenario of the cell configuration used by HAPS and terrestrial. The method of combining footprint exchange and HAPS footprint enhancement is able to improve CINR more than 10 dB compared with the normal footprint configuration for all users location inside the coverage.
-
Heinemann, C; Heinemann, S; Kruppke, B; Worch, H; Thomas, J; Wiesmann, H P; Hanke, T
2016-10-15
A biomimetic strategy was developed in order to prepare organically modified hydroxyapatite (ormoHAP) with spherical shape. The technical approach is based on electric field-assisted migration of calcium ions and phosphate ions into a hydrogel composed of carboxymethylated gelatin. The electric field as well as the carboxymethylation using glucuronic acid (GlcA) significantly accelerates the mineralization process, which makes the process feasible for lab scale production of ormoHAP spheres and probably beyond. A further process was developed for gentle separation of the ormoHAP spheres from the gelatin gel without compromising the morphology of the mineral. The term ormoHAP was chosen since morphological analyses using electron microscopy (SEM, TEM) and element analysis (EDX, FT-IR, XRD) confirmed that carboxymethylated gelatin molecules use to act as organic templates for the formation of nanocrystalline HAP. The hydroxyapatite (HAP) crystals self-organize to form hollow spheres with diameters ranging from 100 to 500nm. The combination of the biocompatible chemical composition and the unique structure of the nanocomposites is considered to be a useful basis for future applications in functionalized degradable biomaterials. A novel bioinspired mineralization process was developed based on electric field-assisted migration of calcium and phosphate ions into biochemically carboxymethylated gelatin acting as organic template. Advantages over conventional hydroxyapatite include particle size distribution and homogeneity as well as achievable mechanical properties of relevant composites. Moreover, specifically developed calcium ion or phosphate ion release during degradation can be useful to adjust the fate of bone cells in order to manipulate remodeling processes. The hollow structure of the spheres can be useful for embedding drugs in the core, encapsulated by the highly mineralized outer shell. In this way, controlled drug release could be achieved, which enables
-
40 CFR Appendix: Table 1 to... - List of Hazardous Air Pollutants (HAP) for Subpart HHH
2010-07-01
... 40 Protection of Environment 11 2010-07-01 2010-07-01 true List of Hazardous Air Pollutants (HAP) for Subpart HHH Table Appendix: Table 1 to Subpart HHH of Part 63 Protection of Environment... HHH of Part 63—List of Hazardous Air Pollutants (HAP) for Subpart HHH CAS Number a Chemical name 75070...
-
Investigation of Catalytic effect sewage sludge combustion ash in the formation of HAPs
Energy Technology Data Exchange (ETDEWEB)
Fullana, A.; Sidhu, S.; Font, R.; Conesa, A.
2002-07-01
Incineration is a very important technique in the treatment of sewage sludge. In 1998 approximately 1,5 million and 2,5 million dry tons of sewage sludge were incinerated in the United States and European Union (EU), respectively. In 1985, only 10% of EU sludge was incinerated, but by 2005 approximately 40% of EU sludge is expected to be incinerated. Use of sewage sludge as agricultural fertilizer was considered the best application for sludge until it was discovered that the presence of heavy metals in sludge could contaminate farmland. The limitations facing landfills and recycling plants and the planned ban on sea disposal has led to the expectation that the role of incineration will increase in the future. The expected increase in sludge incineration has also led to increased scrutiny of the main drawback to the incineration of sewage sludge: the formation of hazard air pollutants (HAP). Sewage sludge incineration has been identified as a very important source of HAPs such as chloro benzenes, chloro phenols, and PCDD/Fs. One of the more important characteristics of sewage sludge incineration is the formation of large amounts of ash, which is rich in known HAP formation catalysts such as Cu and Fe. Thus, the sludge incineration ash is expected to play an important role in the formation of HAPs in the post-combustion zone of a sludge incinerator. in this paper, we present results of our investigation of the catalytic effect of sewage sludge ash on the formation of chloro benzenes and chloro phenols. In this study, pyrolytic gas from sewage sludge was used as reaction gas instead of the synthetic organic mix that has been used in most previous HAPs formation studies. (Author) 4 refs.
-
Directory of Open Access Journals (Sweden)
Hala E Hussein
2017-10-01
Full Text Available Babesia bovis, is a tick borne apicomplexan parasite responsible for important cattle losses globally. Babesia parasites have a complex life cycle including asexual replication in the mammalian host and sexual reproduction in the tick vector. Novel control strategies aimed at limiting transmission of the parasite are needed, but transmission blocking vaccine candidates remain undefined. Expression of HAP2 has been recognized as critical for the fertilization of parasites in the Babesia-related Plasmodium, and is a leading candidate for a transmission blocking vaccine against malaria. Hereby we identified the B. bovis hap2 gene and demonstrated that it is widely conserved and differentially transcribed during development within the tick midgut, but not by blood stage parasites. The hap2 gene was disrupted by transfecting B. bovis with a plasmid containing the flanking regions of the hap2 gene and the GPF-BSD gene under the control of the ef-1α-B promoter. Comparison of in vitro growth between a hap2-KO B. bovis clonal line and its parental wild type strain showed that HAP2 is not required for the development of B. bovis in erythrocytes. However, xanthurenic acid-in vitro induction experiments of sexual stages of parasites recovered after tick transmission resulted in surface expression of HAP2 exclusively in sexual stage induced parasites. In addition, hap2-KO parasites were not able to develop such sexual stages as defined both by morphology and by expression of the B. bovis sexual marker genes 6-Cys A and B. Together, the data strongly suggests that tick midgut stage differential expression of hap2 is associated with the development of B. bovis sexual forms. Overall these studies are consistent with a role of HAP2 in tick stages of the parasite and suggest that HAP2 is a potential candidate for a transmission blocking vaccine against bovine babesiosis.
-
Energy Technology Data Exchange (ETDEWEB)
Nielsen, Malene; Nielsen, Ole-Kenneth; Thomsen, M.
2010-06-15
Updated emission factors for decentralised combined heat and power (CHP) plants with a capacity < 25MWe have been estimated based on project emission measurements as well as emission measurements performed in recent years that were collected. The emission factors valid for 2006/2007 have been estimated for the plant technologies: Municipal solid waste (MSW) incineration plants, plants combusting straw or wood, natural gas fuelled reciprocating engines, biogas fuelled engines, natural gas fuelled gas turbines, gas oil fuelled reciprocating engines, gas oil fuelled gas turbines, steam turbines combusting residual oil and reciprocating engines combusting biomass producer gas based on wood. The emission factors for MSW incineration plants are much lower than the emission factors that were estimated for year 2000. The considerable reduction in the emission factors is a result of lower emission limit values in Danish legislation since 2006 that has lead to installation of new and improved flue gas cleaning systems in most MSW incineration plants. For CHP plants combusting wood or straw no major technical improvements have been implemented. The emission factors for natural gas fuelled reciprocating engines have been reduced since year 2000 as a result of technical improvements that have been carried out due to lower emission limit values in Danish legislation. The NO{sub x} emission factor for natural gas fuelled gas turbines has decreased 62 % since year 2000. This is a result of installation of low-NO{sub x} burners in almost all gas turbines that has been necessary to meet new emission limits in Danish legislation. The emission measurements programme included screening of the emissions of HCB, PCB, PCDD/-F and PBDD/-F. Compared to the Danish national emission decentralized CHP plants are major emission sources for CH{sub 4}, NO{sub x}, SO{sub 2}, heavy metals and HCB. (author)
-
Carbon dioxide emission factors for U.S. coal by origin and destination
Quick, J.C.
2010-01-01
This paper describes a method that uses published data to calculate locally robust CO2 emission factors for U.S. coal. The method is demonstrated by calculating CO2 emission factors by coal origin (223 counties, in 1999) and destination (479 power plants, in 2005). Locally robust CO2 emission factors should improve the accuracy and verification of greenhouse gas emission measurements from individual coal-fired power plants. Based largely on the county origin, average emission factors for U.S. lignite, subbituminous, bituminous, and anthracite coal produced during 1999 were 92.97,91.97,88.20, and 98.91 kg CO2/GJgross, respectively. However, greater variation is observed within these rank classes than between them, which limits the reliability of CO2 emission factors specified by coal rank. Emission factors calculated by destination (power plant) showed greater variation than those listed in the Emissions & Generation Resource Integrated Database (eGRID), which exhibit an unlikely uniformity that is inconsistent with the natural variation of CO2 emission factors for U.S. coal. ?? 2010 American Chemical Society.
-
Energy Technology Data Exchange (ETDEWEB)
1994-07-01
This study was one of a group of assessments of toxic emissions from coal-fired power plants, conducted for DOE during 1993. The motivation for those assessments was the mandate in the 1990 Clean Air Act Amendments that a study be made of emissions of hazardous air pollutants (HAPs) from electric utilities. The report is organized in two volumes. Volume 1: Sampling describes the sampling effort conducted as the basis for this study; Results presents the concentration data on HAPs in the several power plant streams, and reports the results of evaluations and calculations conducted with those data; and Special Topics report on issues such as comparison of sampling methods and vapor/solid distributions of HAPs. Volume 2: Appendices include quality assurance/quality control results, uncertainty analysis for emission factors, and data sheets. This study involved measurements of a variety of substances in solid, liquid, and gaseous samples from input, output, and process streams at the Innovative Clean Coal Technology Demonstration (ICCT) of the Wet Sulfuric Acid-Selective Catalytic Reduction (SNOX) process. The SNOX demonstration is being conducted at Ohio Edison`s Niles Boiler No. 2 which uses cyclone burners to burn bituminous coal. A 35 megawatt slipstream of flue gas from the boiler is used to demonstrate SNOX. The substances measured at the SNOX process were the following: 1. Five major and 16 trace elements, including mercury, chromium, cadmium, lead, selenium, arsenic, beryllium, and nickel; 2. Acids and corresponding anions (HCl, HF, chloride, fluoride, phosphate, sulfate); 3. Ammonia and cyanide; 4. Elemental carbon; 5. Radionuclides; 6. Volatile organic compounds (VOC); 7. Semi-volatile compounds (SVOC) including polynuclear aromatic hydrocarbons (PAH); and 8. Aldehydes.
-
Directory of Open Access Journals (Sweden)
Iskandar Iskandar
2016-07-01
Full Text Available This paper proposes variable step closed loop power control algorithm combined with space diversity to improve the performance of High Altitude Platforms (HAPs communication at low elevation angle using Code Division Multiple Access (CDMA. In this contribution, we first develop HAPs channel model which is derived from experimental measurement. From our experiment, we found HAPs channel characteristic can be modeled as a Ricean distribution because the presence of line of sight path. Different elevation angle resulting different K factor value. This value is then used in Signal to Interference Ratio (SIR based closed loop power control evaluation. The variable step algorithm is simulated under various elevation angles with different speed of mobile user. The performance is presented in terms of user elevation angle, user speed, step size and space diversity order. We found that the performance of variable step closed-loop power control less effective at low elevation angle. However our simulation shows that space diversity is able to improve the performance of closed loop power control for HAPs channel at low elevation angle.*****Kajian ini mengusulkan suatu algoritma kontrol daya langkah variabel loop tertutup dikombinasikan dengan keragaman ruang untuk meningkatkan kinerja komunikasi High Altitude Platforms(HAPs pada sudut elevasi rendah menggunakan Code Division Multiple Access (CDMA. Kami berkontribusi untuk mengembangkan model kanal HAPs yang berasal dari pengukuran eksperimental sebelumnya. Dari percobaan tersebut, kami menemukan karakteristik kanal HAPs yang dapat dimodelkan sebagai distribusi Ricean karena kehadiran jalur tanpa penghalang. Eksperimen menunjukkan bahwa perbedaan sudut elevasi menghasilkan perbedaan nilai factor K. Nilai ini kemudian digunakan dalam Signal to Interference Ratio (SIR berbasiskan evaluasi kontrol daya loop tertutup. Algoritma langkah variabel disimulasikan dibawah sudut elevasi yang berbeda dengan kecepatan
-
Cai, Hao; Xie, Shaodong
2013-03-01
The vehicular emission trend in China was tracked for the recent period 2006-2009 based on a database of dynamic emission factors of CO, nonmethane volatile organic compounds (NMVOC), NOx, PM10, CO2, CH4, and N2O for all categories of on-road motor vehicles in China, which was developed at the provincial level using the COPERT 4 model, to account for the effects of rapid advances in engine technologies, implementation of improved emission standards, emission deterioration due to mileage, and fuel quality improvement. Results show that growth rates of CO and NMVOC emissions slowed down, but NOx and PM10 emissions continued rising rapidly for the period 2006-2009. Moreover CO2, CH4, and N2O emissions in 2009 almost doubled compared to those in 2005. Characteristics of recent spatial distribution of emissions and emission contributions by vehicle category revealed that priority of vehicular emission control should be put on the eastern and southeastern coastal provinces and northern regions, and passenger cars and motorcycles require stricter control for the reduction of CO and NMVOC emissions, while effective reduction of NOx and PM10 emissions can be achieved by better control of heavy-duty vehicles, buses and coaches, and passenger cars. Explicit provincial-level Monte Carlo uncertainty analysis, which quantified for the first time the Chinese vehicular emission uncertainties associated with both COPERT-derived and domestically measured emission factors by vehicle technology, showed that CO, NMVOC, and NOx emissions for the period 2006-2009 were calculated with the least uncertainty, followed by PM10 and CO2, despite relatively larger uncertainties in N2O and CH4 emissions. The quantified low uncertainties of emissions revealed a necessity of applying vehicle technology- and vehicle age-specific dynamic emission factors for vehicular emission estimation, and these improved methodologies are applicable for routine update and forecast of China's on-road motor vehicle
-
Experimental Study on 3D Chi - Hap Scaffolds for Thyroid Cartilage Repairing
Sun, Nannan; Shi, Tingchun; Fan, Yuan; Hu, Binbin
2018-01-01
Due to the limitation of self-repairing capability for cartilage injury, the construction of tissue engineering in vitro has been an ideal treatment to repair tissue injury. In this paper, hydroxyapatite (Hap) and chitosan (Chi) were selected to fabricate the scaffold through low temperature deposition manufacturing (LDM) technique. The scaffold was characterized with interconnected structure and high porosity, as well as lower toxicity to cells (TDC-5-EGPE). Animal experiment was performed, Twelve white New Zealand rabbits were randomly divided into two groups, the side of the thyroid cartilage was removed, Chi-HAP composite scaffold was implanted into the cartilage defect as the experimental group A. Group B was treated for thyroid cartilage defects without any treatment. After 10 weeks, hematoxylin-eosin (HE) staining and S-O staining were carried out on the injured tissues. The result showed that newborn chondrocytes were found in repaired areas for group A, and there are no new cells found for group B. Therefore, Chi-HAP composite scaffolds formed by LDM possess biological activity for repairing injury cartilage.
-
Vu, Minh Q.; Nguyen, Nga T. T.; Pham, Hien T. T.; Dang, Ngoc T.
2018-03-01
High-altitude platforms (HAPs) are flexible, non-pollutant and cost-effective infrastructures compared to satellite or old terrestrial systems. They are being researched and developed widely in Europe, USA, Japan, Korea, and so on. However, the current limited data rates and the overload of radio frequency (RF) spectrum are problems which the developers for HAPs are confronting because most of them use RF links to communicate with the ground stations (GSs) or each other. In this paper, we propose an all-optical two-way half-duplex relaying free-space optical (FSO) communication for HAP-based backhaul networks, which connect the base transceiver station (BTS) to the core network (CN) via a single HAP. Our proposed backhaul solution can be deployed quickly and flexibly for disaster relief and for serving users in both urban environments and remote areas. The key subsystem of HAP is an optical regenerate-and-forward (ORF) equipped with an optical hard-limiter (OHL) and an optical XOR gate to perform all-optical processing and help mitigate the background noise. In addition, two-way half-duplex relaying can be provided thanks to the use of network coding scheme. The closed-form expression for the bit error rate (BER) of our proposed system under the effect of path loss, atmospheric turbulence, and noise induced by the background light is formulated. The numerical results are demonstrated to prove the feasibility of our proposed system with the verification by using Monte-Carlo (M-C) simulations.
-
Health Activities Project (HAP): Sight and Sound Module.
Buller, Dave; And Others
Contained within this Health Activities Project (HAP) learning packet are activities for children in grades 5-8. Design of the activities centers around the idea that students can control their own health and safety. Within this module are teacher and student folios describing six activities which involve students in restricting their vision by…
-
Hazardous air pollutants emission from coal and oil-fired power plants
Energy Technology Data Exchange (ETDEWEB)
Deepak Pudasainee; Jeong-Hun Kim; Sang-Hyeob Lee; Ju-Myon Park; Ha-Na Jang; Geum-Ju Song; Yong-Chil Seo [Yonsei University, Wonju (Republic of Korea). Department of Environmental Engineering
2010-03-15
Hazardous air pollutants (HAPs) emission characteristics from coal (anthracite, bituminous) and oil-fired power plants were studied in order to control pollutants by formulating US maximum achievable control technology (MACT)-like regulation in Korea. Sampling and analysis were carried out according to either Korean standard test method or US EPA method. Relatively lower levels of NOx and SOx were emitted from plants burning bituminous than the anthracite coal. Less dust was emitted from oil-fired power plants. Mercury, lead, and chromium were dominant in coal-fired power plants, following which, nickel and chromium were emitted from oil-fired power plants. The major volatile organic compounds (VOCs) emitted from coal-fired plants were 1,2-dichloroethane, benzene, carbon tetrachloride, chloroform, trichloro-ethylene. The emission of mercury and other heavy metals in flue gas was attributed to fuel types, operating conditions, residence time in the control devices and the type of air pollution control devices. After emission tests in the field and on analysis of the continuous emission monitoring data collected from facilities under operation and consideration of other various factors, management guidelines will be suggested with special reference to US MACT-like regulation.
-
40 CFR 63.5698 - What emission limit must I meet for open molding resin and gel coat operations?
2010-07-01
... open molding resin and gel coat operations? 63.5698 Section 63.5698 Protection of Environment... Manufacturing Standards for Open Molding Resin and Gel Coat Operations § 63.5698 What emission limit must I meet for open molding resin and gel coat operations? (a) You must limit organic HAP emissions from the five...
-
Emissions from laboratory combustion of wildland fuels: Emission factors and source profiles
L.-W. Anthony Chen; Hans Moosmuller; W. Patrick Arnott; Judith C. Chow; John G. Watson; Ronald A. Susott; Ronald E. Babbitt; Cyle E. Wold; Emily N. Lincoln; Wei Min Hao
2007-01-01
Combustion of wildland fuels represents a major source of particulate matter (PM) and light-absorbing elemental carbon (EC) on a national and global scale, but the emission factors and source profiles have not been well characterized with respect to different fuels and combustion phases. These uncertainties limit the accuracy of current emission inventories, smoke...
-
Analysis of Passenger Car Emission Factors in RDE Tests
Directory of Open Access Journals (Sweden)
Pielecha Jacek
2016-01-01
Full Text Available The article presents a study on emission measurements in passenger cars in tests conducted under real traffic conditions – Real Driving Emissions using a Portable Emission Measurement System type of equipment. A special feature of the outlined RDE tests is that they were performed in Polish road conditions, and thus their parameters may differ from their counterparts adopted in most European Union countries. Based on the findings vehicle emission conformity factors were developed, characterized as the fractional increase (or decrease of traffic emissions during the homologation test or under normal operation conditions in relation to the emission limit standards (for chosen emission class of the vehicle. Conducted research and the calculated conformity factors allowed for the environmental impact assessment of the vehicles of various emission classes, while also allowing early actions to restrict the emissions of selected components in passenger vehicles. The methods and measures used can also be applied to other types of vehicles (e.g. heavy duty or off-road vehicles or vehicles powered by other fuels.
-
Influence factors and forecast of carbon emission in China: structure adjustment for emission peak
Wang, B.; Cui, C. Q.; Li, Z. P.
2018-02-01
This paper introduced Principal Component Analysis and Multivariate Linear Regression Model to verify long-term balance relationships between Carbon Emissions and the impact factors. The integrated model of improved PCA and multivariate regression analysis model is attainable to figure out the pattern of carbon emission sources. Main empirical results indicate that among all selected variables, the role of energy consumption scale was largest. GDP and Population follow and also have significant impacts on carbon emission. Industrialization rate and fossil fuel proportion, which is the indicator of reflecting the economic structure and energy structure, have a higher importance than the factor of urbanization rate and the dweller consumption level of urban areas. In this way, some suggestions are put forward for government to achieve the peak of carbon emissions.
-
López-Berges, Manuel S.; Capilla, Javier; Turrà, David; Schafferer, Lukas; Matthijs, Sandra; Jöchl, Christoph; Cornelis, Pierre; Guarro, Josep; Haas, Hubertus; Di Pietro, Antonio
2012-01-01
Soilborne fungal pathogens cause devastating yield losses and are highly persistent and difficult to control. During the infection process, these organisms must cope with limited availability of iron. Here we show that the bZIP protein HapX functions as a key regulator of iron homeostasis and virulence in the vascular wilt fungus Fusarium oxysporum. Deletion of hapX does not affect iron uptake but causes derepression of genes involved in iron-consuming pathways, leading to impaired growth under iron-depleted conditions. F. oxysporum strains lacking HapX are reduced in their capacity to invade and kill tomato (Solanum lycopersicum) plants and immunodepressed mice. The virulence defect of ΔhapX on tomato plants is exacerbated by coinoculation of roots with a biocontrol strain of Pseudomonas putida, but not with a siderophore-deficient mutant, indicating that HapX contributes to iron competition of F. oxysporum in the tomato rhizosphere. These results establish a conserved role for HapX-mediated iron homeostasis in fungal infection of plants and mammals. PMID:22968717
-
Tsujii, Toshiaki; Harigae, Masatoshi
Recently, some feasibility studies on a regional positioning system using the quasi-zenith satellites and the geostationary satellites have been conducted in Japan. However, the geometry of this system seems to be unsatisfactory in terms of the positioning accuracy in north-south direction. In this paper, an augmented satellite positioning system by the High Altitude Platform Systems (HAPS) is proposed since the flexibility of the HAPS location is effective to improve the geometry of satellite positioning system. The improved positioning performance of the augmented system is also demonstrated.
-
Emission factors of Austrian industry production and international comparison. Final report
International Nuclear Information System (INIS)
Turi, K.
1997-05-01
During the last few years a number of measures have been implemented in the Austrian industries to reduce air pollution and energy use. Therefore specific emissions in the various sectors were changed considerably during this period. The aim of this research project was to better characterize air pollutant emissions of the Austrian industry. Emission data as measured by the Austrian industry was compared with published emission factors from international literature. The results show that the emission factors of the Austrian industry are generally lower than literature emission factors. This is because on the one hand many older data from the literature do not reflect current state of the knowledge, and on the other hand because emission reduction measures and new technologies were introduced in the Austrian industry. (author)
-
A Comprehensive Examination of Heavy Vehicle Emissions Factors
2010-08-01
This report summarizes the findings from reviewing the literature on several topics that are related to heavy vehicle emissions including engine and fuel types, vehicle technologies that can be used to reduce or mitigate vehicle emissions, the factor...
-
Energy Technology Data Exchange (ETDEWEB)
Hensmann, Michael; Haardt, Sebastian; Ebert, Dominik [Betriebsforschungsinstitut VDEh-Institut fuer Angewandte Forschung GmbH, Duesseldorf (Germany)
2012-10-15
The German Umweltbundesamt (UBA) records emission factors of important groups of emitters of the iron- and steelmaking industry in a central database named ''Zentrales System Emissionen'' (ZSE) since 1990. This data is being used for calculations of emission inventories. The main purposes are the generation of forecasts, calculating emissions of other plants and the appraisal of potential measures for reduction of pollution. This makes it possible to identify and appraise future problems and measures. Because of steadily increasing requirements to data quality and quality assurance, it became necessary to update the ZSE with characteristical emission data in order to give a representative view of relevant stages in the iron- and steelmaking industry with respect to emissions. In 2008, the VDEh-Betriebsforschungsinstitut (BFI) was assigned to determine up-to-date emission factors for the following relevant stages in the iron- and steelmaking industry: - sintering plant - coking plant - blast furnace - steel making (differentiated between oxygen and electric steel making) - production of rolled steel Due to a wide diversity of data quality, a consecutive project to determine the corresponding uncertainty of the emission factors was integrated into the ongoing project. This is necessary to create reliable forecasts of emissions and to meet national and international duties of reporting. The project was supported by 18 companies of the German iron- and steelmaking industry. A total of 40 relevant sources of emissions were identified within the five stages of steelmaking and taken into consideration. The emission data for documenting organic and inorganic components of harmful gas, heavy metals and air borne dusts in the ZSE was taken from the reports of emissions 2008 of the supporting companies and made up for a total of 63 plants. Due to a wide variety of data quality the emissions of point sources and diffuse sources are treated separately. While
-
40 CFR 63.8055 - How do I comply with a weight percent HAP limit in coating products?
2010-07-01
... HAP limit in coating products? 63.8055 Section 63.8055 Protection of Environment ENVIRONMENTAL...: Miscellaneous Coating Manufacturing Alternative Means of Compliance § 63.8055 How do I comply with a weight percent HAP limit in coating products? (a) As an alternative to complying with the requirements in Table 1...
-
DEMONSTRATION OF NO-VOC/NO-HAP WOOD FURNITURE COATING SYSTEM
The United States Environmental Protection Agency has contracted with AeroVironment Environmental Services, Inc. and its subcontractor, Adhesives Coating Co., to develop and demonstrate a no-VOC (volatile organic compound)/no-HAP (hazardous air pollutant) wood furniture coating s...
-
Energy Technology Data Exchange (ETDEWEB)
M Dongre; N Singh; C Dureja; N Peddada; A Solanki; F Ashish; S Raychaudhuri
2011-12-31
HapR has been recognized as a quorum-sensing master regulator in Vibrio cholerae. Because it controls a plethora of disparate cellular events, the absence of a functional HapR affects the physiology of V. cholerae to a great extent. In the current study, we pursued an understanding of an observation of a natural protease-deficient non-O1, non-O139 variant V. cholerae strain V2. Intriguingly, a nonfunctional HapR (henceforth designated as HapRV2) harboring a substitution of glycine to aspartate at position 39 of the N-terminal hinge region has been identified. An in vitro gel shift assay clearly suggested the inability of HapRV2 to interact with various cognate promoters. Reinstatement of glycine at position 39 restores DNA binding ability of HapRV2 (HapRV2G), thereby rescuing the protease-negative phenotype of this strain. The elution profile of HapRV2 and HapRV2G proteins in size-exclusion chromatography and their circular dichroism spectra did not reflect any significant differences to explain the functional discrepancies between the two proteins. To gain insight into the structure-function relationship of these two proteins, we acquired small/wide angle x-ray scattering data from samples of the native and G39D mutant. Although Guinier analysis and indirect Fourier transformation of scattering indicated only a slight difference in the shape parameters, structure reconstruction using dummy amino acids concluded that although HapR adopts a 'Y' shape similar to its crystal structure, the G39D mutation in hinge drastically altered the DNA binding domains by bringing them in close proximity. This altered spatial orientation of the helix-turn-helix domains in this natural variant provides the first structural evidence on the functional role of the hinge region in quorum sensing-related DNA-binding regulatory proteins of Vibrio spp.
-
International Nuclear Information System (INIS)
Charitidis, Costas A.; Skarmoutsou, Amalia; Tsetsekou, Athena; Brasinika, Despina; Tsiourvas, Dimitris
2013-01-01
Highlights: ► The synthesis of hydroxyapatite (HAP) nanoparticles in the presence of a cationic fourth generation diaminobutane poly(propylene imine) dendrimer (DAB). ► The nanomechanical properties of different HAP-DAB coatings onto titanium surfaces. ► Wear resistance and adhesion properties of the synthesized coatings quantified by nanoindentation data analysis. -- Abstract: Coatings of hydroxyapatite (HAP) nanorods onto titanium surfaces were synthesized with the aim to improve coatings’ mechanical properties and adhesion to the substrate. The coatings are consisting of HAP nanorods synthesized in the presence of a cationic fourth generation diaminobutane poly(propylene imine) dendrimer (DAB) bearing 32 amine end groups employing varying calcium: dendrimer ratios and varying hydrothermal treatments. The quality, surface morphology and structure of the coatings were characterized with X-ray diffraction, thermogravimetric analysis, scanning electron microscopy and energy dispersive microanalysis. Wear resistance and adhesion properties of the coatings onto titanium substrates were studied through nanoindentation analysis. The experimental conditions, namely the calcium: dendrimer molar ratio and the hydrothermal treatment temperature were carefully selected; thus, it was possible to produce coatings of high hardness and elastic modulus values (ranging between 1–4.5 GPa and 40–150 GPa, respectively) and/or high wear resistance and plastic deformation values
-
Energy Technology Data Exchange (ETDEWEB)
Charitidis, Costas A., E-mail: charitidis@chemeng.ntua.gr [School of Chemical Engineering, National Technical University of Athens, Iroon Polytechniou, Zografou, 15780 Athens (Greece); Skarmoutsou, Amalia [School of Chemical Engineering, National Technical University of Athens, Iroon Polytechniou, Zografou, 15780 Athens (Greece); Tsetsekou, Athena; Brasinika, Despina [School of Mining Engineering and Metallurgy, National Technical University of Athens, Iroon Polytechniou, Zografou, 15780 Athens (Greece); Tsiourvas, Dimitris [National Centre for Scientific Research “Demokritos”, Institute of Physical Chemistry, Agia Paraskevi, 15310 Athens (Greece)
2013-04-20
Highlights: ► The synthesis of hydroxyapatite (HAP) nanoparticles in the presence of a cationic fourth generation diaminobutane poly(propylene imine) dendrimer (DAB). ► The nanomechanical properties of different HAP-DAB coatings onto titanium surfaces. ► Wear resistance and adhesion properties of the synthesized coatings quantified by nanoindentation data analysis. -- Abstract: Coatings of hydroxyapatite (HAP) nanorods onto titanium surfaces were synthesized with the aim to improve coatings’ mechanical properties and adhesion to the substrate. The coatings are consisting of HAP nanorods synthesized in the presence of a cationic fourth generation diaminobutane poly(propylene imine) dendrimer (DAB) bearing 32 amine end groups employing varying calcium: dendrimer ratios and varying hydrothermal treatments. The quality, surface morphology and structure of the coatings were characterized with X-ray diffraction, thermogravimetric analysis, scanning electron microscopy and energy dispersive microanalysis. Wear resistance and adhesion properties of the coatings onto titanium substrates were studied through nanoindentation analysis. The experimental conditions, namely the calcium: dendrimer molar ratio and the hydrothermal treatment temperature were carefully selected; thus, it was possible to produce coatings of high hardness and elastic modulus values (ranging between 1–4.5 GPa and 40–150 GPa, respectively) and/or high wear resistance and plastic deformation values.
-
Pekala, Ronald J; Kumar, V K; Maurer, Ronald; Elliott-Carter, Nancy; Moon, Edward; Mullen, Karen
2010-04-01
This study sought to determine if self-reported hypnotic depth (srHD) could be predicted from the variables of the Phenomenology of Consciousness Inventory - Hypnotic Assessment Procedure (PCI-HAP) (Pekala, 1995a, 1995b; Pekala & Kumar, 2007; Pekala et al., 2010), assessing several of the processes theorized by researchers to be associated with hypnotism: trance (altered state effects), suggestibility, and expectancy. One hundred and eighty participants completed the PCI-HAP. Using regression analyses, srHD scores were predicted from the PCI-HAP pre-hypnotic and post-hypnotic assessment items, and several other variables. The results suggested that the srHD scores were found to be a function of imagoic suggestibility, expectancy (both estimated hypnotic depth and expected therapeutic efficacy), and trance state and eye catalepsy effects; effects that appear to be additive and not (statistically) interactive. The results support the theorizing of many investigators concerning the involvement of the aforementioned component processes with this particular aspect of hypnotism, the self-reported hypnotic depth score.
-
Pühapäeval toimub kunstihoones esimene JazziMaali võistlus
2008-01-01
Rahvusvahelise dzhässikuu raames toimub Tallinna Kunstihoones JazziMaali pühapäev, kus musitseerib Estonian Guitar Octet ning maalivad Pelgulinna gümnaasiumi, Tallinna kunstikooli ja Sally Stuudio õpilased
-
Influence of HAp on the polymerization processes of a possible radioactive bone cement
Energy Technology Data Exchange (ETDEWEB)
Montaño, Carlos J.; Campos, Tarcísio P.R., E-mail: carlmont@ucm.es, E-mail: tprcampos@yahoo.com.br [Universidade Federal de Minas Gerais (UFMG), Belo Horizonte (Brazil). Dept. de Engenharia Nuclear. Lab. de Radiações Ionizantes; Silva, Adolfo H.M.; Araujo, Maria H., E-mail: adolfohmoraes@ufmg.br, E-mail: mharaujo1993@gmail.com [Universidade Federal de Minas Gerais (RMN/UFMG), Belo Horizonte (Brazil). Dept. de Ressonância Magnética Nuclear
2017-07-01
Polymethylmethacrylate PMMA is an acrylic that has been already proposed as a composite to adhere together the fractured bone structures. Subsequently, augmentation bone cements have incorporated Calcium Biophosphonates as vital part of its components to increase the biocompatibility with osseous tissues. Minimally invasive percutaneous techniques such as Vertebroplasty and Kyphoplasty have been developed to reduce surgical impact on patients, but in turn have been reported undesirable effects as extravasation of the cement outside of the planning target volume due to the compression of the internal bone fluids or other tissues. An in situ variable that helps favoring of the PMMA polymerization process is the temperature; however, it may bring deleterious effects. On the methodology, an assay was addressed varying the Hydroxyapatite HAp concentration. Also the cement processing was modified by setting water as a vehicle for particle dispersion. The ratios of HAp/PMMA concentrations were: 0.00000, 0.02167, 0.09062, 0.16619 and 0.50000 mixed in PMMA and liquid catalyst and monomer. The thermal profiles were measured during polymerization and analyzed. Nuclear magnetic resonance NMR analysis was carried out on the polymerization process in an aqueous state to monitor the H-H{sub 2}O proton signal. As results, an increasing in the cement hardness time was found in the proportion of the HAp concentration. The highest τ polymerization time was found for the x{sub 5} concentration and the signal from the water trapped in the HAp amorphous lattice was determined around ∼5 ppm in the {sup 1}H NMR spectra. (author)
-
Influence of HAp on the polymerization processes of a possible radioactive bone cement
International Nuclear Information System (INIS)
Montaño, Carlos J.; Campos, Tarcísio P.R.; Silva, Adolfo H.M.; Araujo, Maria H.
2017-01-01
Polymethylmethacrylate PMMA is an acrylic that has been already proposed as a composite to adhere together the fractured bone structures. Subsequently, augmentation bone cements have incorporated Calcium Biophosphonates as vital part of its components to increase the biocompatibility with osseous tissues. Minimally invasive percutaneous techniques such as Vertebroplasty and Kyphoplasty have been developed to reduce surgical impact on patients, but in turn have been reported undesirable effects as extravasation of the cement outside of the planning target volume due to the compression of the internal bone fluids or other tissues. An in situ variable that helps favoring of the PMMA polymerization process is the temperature; however, it may bring deleterious effects. On the methodology, an assay was addressed varying the Hydroxyapatite HAp concentration. Also the cement processing was modified by setting water as a vehicle for particle dispersion. The ratios of HAp/PMMA concentrations were: 0.00000, 0.02167, 0.09062, 0.16619 and 0.50000 mixed in PMMA and liquid catalyst and monomer. The thermal profiles were measured during polymerization and analyzed. Nuclear magnetic resonance NMR analysis was carried out on the polymerization process in an aqueous state to monitor the H-H 2 O proton signal. As results, an increasing in the cement hardness time was found in the proportion of the HAp concentration. The highest τ polymerization time was found for the x 5 concentration and the signal from the water trapped in the HAp amorphous lattice was determined around ∼5 ppm in the 1 H NMR spectra. (author)
-
Guérette, Elise-Andrée; Paton-Walsh, Clare; Desservettaz, Maximilien; Smith, Thomas E. L.; Volkova, Liubov; Weston, Christopher J.; Meyer, Carl P.
2018-03-01
We characterised trace gas emissions from Australian temperate forest fires through a mixture of open-path Fourier transform infrared (OP-FTIR) measurements and selective ion flow tube mass spectrometry (SIFT-MS) and White cell FTIR analysis of grab samples. We report emission factors for a total of 25 trace gas species measured in smoke from nine prescribed fires. We find significant dependence on modified combustion efficiency (MCE) for some species, although regional differences indicate that the use of MCE as a proxy may be limited. We also find that the fire-integrated MCE values derived from our in situ on-the-ground open-path measurements are not significantly different from those reported for airborne measurements of smoke from fires in the same ecosystem. We then compare our average emission factors to those measured for temperate forest fires elsewhere (North America) and for fires in another dominant Australian ecosystem (savanna) and find significant differences in both cases. Indeed, we find that although the emission factors of some species agree within 20 %, including those of hydrogen cyanide, ethene, methanol, formaldehyde and 1,3-butadiene, others, such as acetic acid, ethanol, monoterpenes, ammonia, acetonitrile and pyrrole, differ by a factor of 2 or more. This indicates that the use of ecosystem-specific emission factors is warranted for applications involving emissions from Australian forest fires.
-
DEFF Research Database (Denmark)
Kilian, Mogens; Poulsen, Knud; Lomholt, Hans Bredsted
2002-01-01
genetic polymorphism and pronounced mosaic-like patterns in both genes, but no evidence of intrastrain recombination between the two genes. A conserved hap pseudogene was present in all strains of H. aegyptius and H. influenzae biogroup aegyptius, each of which constituted distinct subpopulations...... on conjunctival cells, previously termed microcolony formation. The fact that individual hap pseudogenes differed from the ancestral sequence by zero to two positions within a 1.5 kb stretch suggests that the silencing event happened approximately 2000-11,000 years ago. Divergence of H. aegyptius and H...
-
Meng, Guoyu; Spahich, Nicole; Kenjale, Roma; Waksman, Gabriel; St Geme, Joseph W
2011-01-01
Bacterial biofilms are complex microbial communities that are common in nature and are being recognized increasingly as an important determinant of bacterial virulence. However, the structural determinants of bacterial aggregation and eventual biofilm formation have been poorly defined. In Gram-negative bacteria, a major subgroup of extracellular proteins called self-associating autotransporters (SAATs) can mediate cell–cell adhesion and facilitate biofilm formation. In this study, we used the Haemophilus influenzae Hap autotransporter as a prototype SAAT to understand how bacteria associate with each other. The crystal structure of the H. influenzae HapS passenger domain (harbouring the SAAT domain) was determined to 2.2 Å by X-ray crystallography, revealing an unprecedented intercellular oligomerization mechanism for cell–cell interaction. The C-terminal SAAT domain folds into a triangular-prism-like structure that can mediate Hap–Hap dimerization and higher degrees of multimerization through its F1–F2 edge and F2 face. The intercellular multimerization can give rise to massive buried surfaces that are required for overcoming the repulsive force between cells, leading to bacterial cell–cell interaction and formation of complex microcolonies. PMID:21841773
-
Directory of Open Access Journals (Sweden)
Veljović Đ.
2013-01-01
Full Text Available Composites based on HAP and oxidized multi-walled carbon nanotubes (o-MWCNT and monophase HAP materials were processed by spark plasma sintering. Starting from stoichiometric nano-sized HAP powder, monophase bioceramics were obtained with a density close to the theoretical one and with an average grain size of several hundred nanometers to micron dimensions. It was shown that decreasing the sintering temperature resulted in a decrease of the grain size, which affected an increase in the fracture toughness and hardness. The fracture toughness of an HAP/ o-MWCNT bioceramic processed at 900°C for only 5 min was 30 % higher than that of monophase HAP materials obtained under the same conditions. The addition of MWCNT during SPS processing of HAP materials caused a decrease in the grain size to the nano-dimension, which was one of the reasons for the improved mechanical properties. [Projekat Ministarstva nauke Republike Srbije, br. III45019 i FP7-REGPOT-2009-1 NANOTECH FTM, Grant Agreement Number: 245916
-
Health Activities Project (HAP): Heart Fitness and Action Module.
Buller, Dave; And Others
Contained within this Health Activities Project (HAP) learning packet are activities for children in grades 5-8. Design of the activities centers around the idea that students can control their own health and safety. Within the Heart Fitness and Action Module are teacher and student folios describing five activities which involve students in…
-
Bao, Wei-Guo; Guiard, Bernard; Fang, Zi-An; Donnini, Claudia; Gervais, Michel; Passos, Flavia M. Lopes; Ferrero, Iliana; Fukuhara, Hiroshi; Bolotin-Fukuhara, Monique
2008-01-01
The HAP1 (CYP1) gene product of Saccharomyces cerevisiae is known to regulate the transcription of many genes in response to oxygen availability. This response varies according to yeast species, probably reflecting the specific nature of their oxidative metabolism. It is suspected that a difference in the interaction of Hap1p with its target genes may explain some of the species-related variation in oxygen responses. As opposed to the fermentative S. cerevisiae, Kluyveromyces lactis is an aerobic yeast species which shows different oxygen responses. We examined the role of the HAP1-equivalent gene (KlHAP1) in K. lactis. KlHap1p showed a number of sequence features and some gene targets (such as KlCYC1) in common with its S. cerevisiae counterpart, and KlHAP1 was capable of complementing the hap1 mutation. However, the KlHAP1 disruptant showed temperature-sensitive growth on glucose, especially at low glucose concentrations. At normal temperature, 28°C, the mutant grew well, the colony size being even greater than that of the wild type. The most striking observation was that KlHap1p repressed the expression of the major glucose transporter gene RAG1 and reduced the glucose uptake rate. This suggested an involvement of KlHap1p in the regulation of glycolytic flux through the glucose transport system. The ΔKlhap1 mutant showed an increased ability to produce ethanol during aerobic growth, indicating a possible transformation of its physiological property to Crabtree positivity or partial Crabtree positivity. Dual roles of KlHap1p in activating respiration and repressing fermentation may be seen as a basis of the Crabtree-negative physiology of K. lactis. PMID:18806211
-
HapHop-Physio: a computer game to support cognitive therapies in children.
Rico-Olarte, Carolina; López, Diego M; Narváez, Santiago; Farinango, Charic D; Pharow, Peter S
2017-01-01
Care and support of children with physical or mental disabilities are accompanied with serious concerns for parents, families, healthcare institutions, schools, and their communities. Recent studies and technological innovations have demonstrated the feasibility of providing therapy and rehabilitation services to children supported by computer games. The aim of this paper is to present HapHop-Physio, an innovative computer game that combines exercise with fun and learning, developed to support cognitive therapies in children. Conventional software engineering methods such as the Scrum methodology, a functionality test and a related usability test, were part of the comprehensive methodology adapted to develop HapHop-Physio. The game supports visual and auditory attention therapies, as well as visual and auditory memory activities. The game was developed by a multidisciplinary team, which was based on the Hopscotch ® platform provided by Fraunhofer Institute for Digital Media Technology IDMT Institute in Germany, and designed in collaboration with a rehabilitation clinic in Colombia. HapHop-Physio was tested and evaluated to probe its functionality and user satisfaction. The results show the development of an easy-to-use and funny game by a multidisciplinary team using state-of-the-art videogame technologies and software methodologies. Children testing the game concluded that they would like to play again while undergoing rehabilitation therapies.
-
Lasko, Kristofer; Vadrevu, Krishna
2018-01-01
In Southeast Asia and Vietnam, rice residues are routinely burned after the harvest to prepare fields for the next season. Specific to Vietnam, the two prevalent burning practices include: a). piling the residues after hand harvesting; b). burning the residues without piling, after machine harvesting. In this study, we synthesized field and laboratory studies from the literature on rice residue burning emission factors for Particulate Matter less than 2.5 microns (PM2.5). We found significant differences in the resulting burning-practice specific emission factors, with 16.9 grams per square kilogram (plus or minus 6.9) for pile burning and 8.8 grams per square kilogram (plus or minus 3.5) for non-pile burning. We calculated burning practice specific emissions based on rice area data, region-specific fuel-loading factors, combined emission factors, and estimates of burning from the literature. Our results for year 2015 estimate 180 gigagrams of PM2.5 result from the pile burning method and 130 gigagrams result from non-pile burning method, with the most-likely current emission scenario of 150 gigagrams PM2.5 emissions for Vietnam. For comparison purposes, we calculated emissions using generalized agricultural emission factors employed in global biomass burning studies. These results estimate 80 gigagrams PM2.5, which is only 44 percent of the pile burning-based estimates, suggesting underestimation in previous studies. We compare our emissions to an existing all-combustion sources inventory, results show emissions account for 14-18 percent of Vietnam's total PM2.5 depending on burning practice. Within the highly-urbanized and cloud-covered Hanoi Capital region (HCR), we use rice area from Sentinel-1A to derive spatially-explicit emissions and indirectly estimate residue burning dates. Results from HYSPLIT (Hybrid Single-Particle Lagrangian Integrated Trajectory) back-trajectory analysis stratified by season show autumn has most emission trajectories originating in
-
International Nuclear Information System (INIS)
Wang, Qunwei; Chiu, Yung-Ho; Chiu, Ching-Ren
2015-01-01
Research on the driving factors behind carbon dioxide emission changes in China can inform better carbon emission reduction policies and help develop a low-carbon economy. As one of important methods, production-theoretical decomposition analysis (PDA) has been widely used to understand these driving factors. To avoid the infeasibility issue in solving the linear programming, this study proposed a modified PDA approach to decompose carbon dioxide emission changes into seven drivers. Using 2005–2010 data, the study found that economic development was the largest factor of increasing carbon dioxide emissions. The second factor was energy structure (reflecting potential carbon), and the third factor was low energy efficiency. Technological advances, energy intensity reductions, and carbon dioxide emission efficiency improvements were the negative driving factors reducing carbon dioxide emission growth rates. Carbon dioxide emissions and driving factors varied significantly across east, central and west China. - Highlights: • A modified PDA used to decompose carbon dioxide emission changes into seven drivers. • Two models were proposed to ameliorate the infeasible occasions. • Economic development was the largest factor of increasing CO_2 emissions in China.
-
Particle and VOC emission factor measurements for anthropogenic sources in West Africa
Directory of Open Access Journals (Sweden)
S. Keita
2018-06-01
Full Text Available A number of campaigns have been carried out to establish the emission factors of pollutants from fuel combustion in West Africa, as part of work package 2 (Air Pollution and Health of the DACCIWA (Dynamics-Aerosol-Chemistry-Cloud Interactions in West Africa FP7 program. Emission sources considered here include wood (hevea and iroko and charcoal burning, charcoal making, open trash burning, and vehicle emissions, including trucks, cars, buses and two-wheeled vehicles. Emission factors of total particulate matter (TPM, elemental carbon (EC, primary organic carbon (OC and volatile organic compounds (VOCs have been established. In addition, emission factor measurements were performed in combustion chambers in order to reproduce field burning conditions for a tropical hardwood (hevea, and obtain particulate emission factors by size (PM0.25, PM1, PM2.5 and PM10. Particle samples were collected on quartz fiber filters and analyzed using gravimetric method for TPM and thermal methods for EC and OC. The emission factors of 58 VOC species were determined using offline sampling on a sorbent tube. Emission factor results for two species of tropical hardwood burning of EC, OC and TPM are 0.98 ± 0.46 g kg−1 of fuel burned (g kg−1, 11.05 ± 4.55 and 41.12 ± 24.62 g kg−1, respectively. For traffic sources, the highest emission factors among particulate species are found for the two-wheeled vehicles with two-stroke engines (2.74 g kg−1 fuel for EC, 65.11 g kg−1 fuel for OC and 496 g kg−1 fuel for TPM. The largest VOC emissions are observed for two-stroke two-wheeled vehicles, which are up to 3 times higher than emissions from light-duty and heavy-duty vehicles. Isoprene and monoterpenes, which are usually associated with biogenic emissions, are present in almost all anthropogenic sources investigated during this work and could be as significant as aromatic emissions in wood burning (1 g kg−1 fuel. EC is
-
Dong, Feng; Long, Ruyin; Chen, Hong; Li, Xiaohui; Yang, Qingliang
2013-01-01
China is considered to be the main carbon producer in the world. The per-capita carbon emissions indicator is an important measure of the regional carbon emissions situation. This study used the LMDI factor decomposition model–panel co-integration test two-step method to analyze the factors that affect per-capita carbon emissions. The main results are as follows. (1) During 1997, Eastern China, Central China, and Western China ranked first, second, and third in the per-capita carbon emissions, while in 2009 the pecking order changed to Eastern China, Western China, and Central China. (2) According to the LMDI decomposition results, the key driver boosting the per-capita carbon emissions in the three economic regions of China between 1997 and 2009 was economic development, and the energy efficiency was much greater than the energy structure after considering their effect on restraining increased per-capita carbon emissions. (3) Based on the decomposition, the factors that affected per-capita carbon emissions in the panel co-integration test showed that Central China had the best energy structure elasticity in its regional per-capita carbon emissions. Thus, Central China was ranked first for energy efficiency elasticity, while Western China was ranked first for economic development elasticity. PMID:24353753
-
Low HAP/VOC Compliant Resins for Military Applications
2011-09-01
commumty that was dooradng the perchlorote. Soy Oil 1Walls’ Win Against Perchlorate Texas Military Facility Gets EPA, State OK for Reuse T he...accomplishment is rhe soy - bean, or to be more precise its derivative, soy oil , which cleaned up the chemicals and saved millions of dollars. 5 Army’s Soy ...Fourier Transform Infrared Spectroscopy GM: Glycidyl methacrylate GPC: Gel Permeation Chromatography HAP: Hazardous Air Pollutants HMMWV: High
-
Viadas, Cristina; Ruiz de los Mozos, Igor; Valle, Jaione; Bengoechea, José Antonio; Garmendia, Junkal
2015-01-01
Nontypable Haemophilus influenzae (NTHi) is a major cause of opportunistic respiratory tract disease, and initiates infection by colonizing the nasopharynx. Bacterial surface proteins play determining roles in the NTHi-airways interplay, but their specific and relative contribution to colonization and infection of the respiratory tract has not been addressed comprehensively. In this study, we focused on the ompP5 and hap genes, present in all H. influenzae genome sequenced isolates, and encoding the P5 and Hap surface proteins, respectively. We employed isogenic single and double mutants of the ompP5 and hap genes generated in the pathogenic strain NTHi375 to evaluate P5 and Hap contribution to biofilm growth under continuous flow, to NTHi adhesion, and invasion/phagocytosis on nasal, pharyngeal, bronchial, alveolar cultured epithelial cells and alveolar macrophages, and to NTHi murine pulmonary infection. We show that P5 is not required for bacterial biofilm growth, but it is involved in NTHi interplay with respiratory cells and in mouse lung infection. Mechanistically, P5NTHi375 is not a ligand for CEACAM1 or α5 integrin receptors. Hap involvement in NTHi375-host interaction was shown to be limited, despite promoting bacterial cell adhesion when expressed in H. influenzae RdKW20. We also show that Hap does not contribute to bacterial biofilm growth, and that its absence partially restores the deficiency in lung infection observed for the ΔompP5 mutant. Altogether, this work frames the relative importance of the P5 and Hap surface proteins in NTHi virulence. PMID:25894755
-
Directory of Open Access Journals (Sweden)
Adrien eGirard
2016-04-01
Full Text Available The fingertips are one of the most important and sensitive parts of our body.They are the first stimulated areas of the hand when we interact with our environment.Providing haptic feedback to the fingertips in virtual reality could thus drastically improve perception and interaction with virtual environments.In this paper, we present a modular approach called HapTip to display such haptic sensations at the level of the fingertips.This approach relies on a wearable and compact haptic device able to simulate 2 Degree of Freedom (DoF shear forces on the fingertip with a displacement range of +/- 2 mm. Several modules can be added and used jointly in order to address multi-finger and/or bimanual scenarios in virtual environments.For that purpose, we introduce several haptic rendering techniques to cover different cases of 3D interaction such as touching a rough virtual surface, or feeling the inertia or weight of a virtual object.In order to illustrate the possibilities offered by HapTip, we provide four use cases focused on touching or grasping virtual objects.To validate the efficiency of our approach, we also conducted experiments to assess the tactile perception obtained with HapTip.Our results show that participants can successfully discriminate the directions of the 2 DoF stimulation of our haptic device.We found also that participants could well perceive different weights of virtual objects simulated using two HapTip devices. We believe that HapTip could be used in numerous applications in virtual reality for which 3D manipulation and tactile sensations are often crucial, such as in virtual prototyping or virtual training.
-
Pühapäev kunsti ja muusikaga / Mari Hiiemäe
Hiiemäe, Mari
2008-01-01
Jazzkaare 20. aprillil korraldatavast kunsti ja muusika pühapäevast Niguliste muuseumis (esineb East-West Quartet), Tallinna Kunstihoones (Estonian Guitar Octet), Rotermanni soolalaos (Raivo Tafenau ja Meelis Vindi duo) ja Kumu auditooriumis (laulja Kelli Uustani plaadiesitlus)
-
2010-07-01
... HAP content of aluminum wipedown solvents and aluminum recreational boat surface coatings? 63.5753... Standards for Hazardous Air Pollutants for Boat Manufacturing Standards for Aluminum Recreational Boat Surface Coating Operations § 63.5753 How do I calculate the combined organic HAP content of aluminum...
-
Revisiting factors controlling methane emissions from high-Arctic tundra
DEFF Research Database (Denmark)
Mastepanov, M.; Sigsgaard, C.; Tagesson, T.
2013-01-01
controlling methane emission, i.e. temperature and water table position. Late in the growing season CH4 emissions were found to be very similar between the study years (except the extremely dry 2010) despite large differences in climatic factors (temperature and water table). Late-season bursts of CH4...... short-term control factors (temperature and water table). Our findings suggest the importance of multiyear studies with a continued focus on shoulder seasons in Arctic ecosystems....
-
Factor Decomposition Analysis of Energy-Related CO2 Emissions in Tianjin, China
Directory of Open Access Journals (Sweden)
Zhe Wang
2015-07-01
Full Text Available Tianjin is the largest coastal city in northern China with rapid economic development and urbanization. Energy-related CO2 emissions from Tianjin’s production and household sectors during 1995–2012 were calculated according to the default carbon-emission coefficients provided by the Intergovernmental Panel on Climate Change. We decomposed the changes in CO2 emissions resulting from 12 causal factors based on the method of Logarithmic Mean Divisia Index. The examined factors were divided into four types of effects: energy intensity effect, structure effect, activity intensity effect, scale effect and the various influencing factors imposed differential impacts on CO2 emissions. The decomposition outcomes indicate that per capita GDP and population scale are the dominant positive driving factors behind the growth in CO2 emissions for all sectors, while the energy intensity of the production sector is the main contributor to dampen the CO2 emissions increment, and the contributions from industry structure and energy structure need further enhancement. The analysis results reveal the reasons for CO2 emission changes in Tianjin and provide a solid basis upon which policy makers may propose emission reduction measures and approaches for the implementation of sustainable development strategies.
-
Temperature Dependence of Factors Controlling Isoprene Emissions
Duncan, Bryan N.; Yoshida, Yasuko; Damon, Megan R.; Douglass, Anne R.; Witte, Jacquelyn C.
2009-01-01
We investigated the relationship of variability in the formaldehyde (HCHO) columns measured by the Aura Ozone Monitoring Instrument (OMI) to isoprene emissions in the southeastern United States for 2005-2007. The data show that the inferred, regional-average isoprene emissions varied by about 22% during summer and are well correlated with temperature, which is known to influence emissions. Part of the correlation with temperature is likely associated with other causal factors that are temperature-dependent. We show that the variations in HCHO are convolved with the temperature dependence of surface ozone, which influences isoprene emissions, and the dependence of the HCHO column to mixed layer height as OMI's sensitivity to HCHO increases with altitude. Furthermore, we show that while there is an association of drought with the variation in HCHO, drought in the southeastern U.S. is convolved with temperature.
-
Pre-Harvest Sugarcane Burning: Determination of Emission Factors through Laboratory Measurements
Directory of Open Access Journals (Sweden)
João Andrade Carvalho
2012-02-01
Full Text Available Sugarcane is an important crop for the Brazilian economy and roughly 50% of its production is used to produce ethanol. However, the common practice of pre-harvest burning of sugarcane straw emits particulate material, greenhouse gases, and tropospheric ozone precursors to the atmosphere. Even with policies to eliminate the practice of pre-harvest sugarcane burning in the near future, there is still significant environmental damage. Thus, the generation of reliable inventories of emissions due to this activity is crucial in order to assess their environmental impact. Nevertheless, the official Brazilian emissions inventory does not presently include the contribution from pre-harvest sugarcane burning. In this context, this work aims to determine sugarcane straw burning emission factors for some trace gases and particulate material smaller than 2.5 μm in the laboratory. Excess mixing ratios for CO2, CO, NOX, UHC (unburned hydrocarbons, and PM2.5 were measured, allowing the estimation of their respective emission factors. Average estimated values for emission factors (g kg−1 of burned dry biomass were 1,303 ± 218 for CO2, 65 ± 14 for CO, 1.5 ± 0.4 for NOX, 16 ± 6 for UHC, and 2.6 ± 1.6 for PM2.5. These emission factors can be used to generate more realistic emission inventories and therefore improve the results of air quality models.
-
Abdal-hay, Abdalla; Amna, Touseef; Lim, Jae Kyoo
2013-04-01
The present study was aimed at designing a novel porous hydroxyapatite/poly(ɛ-caprolactone) (nHAp/PCL) hybrid nanocomposite matrix on a magnesium substrate with high and low porosity. The coated samples were prepared using a dip-coating technique in order to enhance the bioactivity and biocompatibility of the implant and to control the degradation rate of magnesium alloys. The mechanical and biocompatible properties of the coated and uncoated samples were investigated and an in vitro test for corrosion was conducted by electrochemical polarization and measurement of weight loss. The corrosion test results demonstrated that both the pristine PCL and nHAp/PCL composites showed good corrosion resistance in SBF. However, during the extended incubation time, the composite coatings exhibited more uniform and superior resistance to corrosion attack than pristine PCL, and were able to survive severe localized corrosion in physiological solution. Furthermore, the bioactivity of the composite film was determined by the rapid formation of uniform CaP nanoparticles on the sample surfaces during immersion in SBF. The mechanical integrity of the composite coatings displayed better performance (˜34% higher) than the uncoated samples. Finally, our results suggest that the nHAp incorporated with novel PCL composite membranes on magnesium substrates may serve as an excellent 3-D platform for cell attachment, proliferation, migration, and growth in bone tissue. This novel as-synthesized nHAp/PCL membrane on magnesium implants could be used as a potential material for orthopedic applications in the future.
-
Emission factors from residential combustion appliances burning Portuguese biomass fuels.
Fernandes, A P; Alves, C A; Gonçalves, C; Tarelho, L; Pio, C; Schimdl, C; Bauer, H
2011-11-01
Smoke from residential wood burning has been identified as a major contributor to air pollution, motivating detailed emission measurements under controlled conditions. A series of experiments were performed to compare the emission levels from two types of wood-stoves to those of fireplaces. Eight types of biomass were burned in the laboratory: wood from seven species of trees grown in the Portuguese forest (Pinus pinaster, Eucalyptus globulus, Quercus suber, Acacia longifolia, Quercus faginea, Olea europaea and Quercus ilex rotundifolia) and briquettes produced from forest biomass waste. Average emission factors were in the ranges 27.5-99.2 g CO kg(-1), 552-1660 g CO(2) kg(-1), 0.66-1.34 g NO kg(-1), and 0.82-4.94 g hydrocarbons kg(-1) of biomass burned (dry basis). Average particle emission factors varied between 1.12 and 20.06 g kg(-1) biomass burned (dry basis), with higher burn rates producing significantly less particle mass per kg wood burned than the low burn rates. Particle mass emission factors from wood-stoves were lower than those from the fireplace. The average emission factors for organic and elemental carbon were in the intervals 0.24-10.1 and 0.18-0.68 g kg(-1) biomass burned (dry basis), respectively. The elemental carbon content of particles emitted from the energy-efficient "chimney type" logwood stove was substantially higher than in the conventional cast iron stove and fireplace, whereas the opposite was observed for the organic carbon fraction. Pinus pinaster, the only softwood species among all, was the biofuel with the lowest emissions of particles, CO, NO and hydrocarbons.
-
Dacunto, Philip J; Cheng, Kai-Chung; Acevedo-Bolton, Viviana; Jiang, Ruo-Ting; Klepeis, Neil E; Repace, James L; Ott, Wayne R; Hildemann, Lynn M
2013-08-01
Indoor sources can greatly contribute to personal exposure to particulate matter less than 2.5 μm in diameter (PM2.5). To accurately assess PM2.5 mass emission factors and concentrations, real-time particle monitors must be calibrated for individual sources. Sixty-six experiments were conducted with a common, real-time laser photometer (TSI SidePak™ Model AM510 Personal Aerosol Monitor) and a filter-based PM2.5 gravimetric sampler to quantify the monitor calibration factors (CFs), and to estimate emission factors for common indoor sources including cigarettes, incense, cooking, candles, and fireplaces. Calibration factors for these indoor sources were all significantly less than the factory-set CF of 1.0, ranging from 0.32 (cigarette smoke) to 0.70 (hamburger). Stick incense had a CF of 0.35, while fireplace emissions ranged from 0.44-0.47. Cooking source CFs ranged from 0.41 (fried bacon) to 0.65-0.70 (fried pork chops, salmon, and hamburger). The CFs of combined sources (e.g., cooking and cigarette emissions mixed) were linear combinations of the CFs of the component sources. The highest PM2.5 emission factors per time period were from burned foods and fireplaces (15-16 mg min(-1)), and the lowest from cooking foods such as pizza and ground beef (0.1-0.2 mg min(-1)).
-
2016-03-01
ARL-TN-0742 ● MAR 2016 US Army Research Laboratory Performance Assessment of Hazardous Air Pollutant (HAP)–Free Chemical Paint...the originator. ARL-TN-0742 ● MAR 2016 US Army Research Laboratory Performance Assessment of Hazardous Air Pollutant (HAP...COVERED (From - To) 1–30 April 2014 4. TITLE AND SUBTITLE Performance Assessment of Hazardous Air Pollutant (HAP)–Free Chemical Paint Strippers
-
Development of cotton gin PM10 emission factors for EPA’s AP-42
The Compilation of Air Pollution Emission Factors (AP-42) emission factors are assigned ratings, from A (Excellent) to E (Poor), based on the quality of data used to develop them. All current PM10 cotton gin emission factors received quality ratings of D or lower. In an effort to improve these ratin...
-
On the High Altitude Platform (HAP W-CDMA System Capacity
Directory of Open Access Journals (Sweden)
L. de Haro-Ariet
2004-06-01
Full Text Available The performance of a downlink power control model, based on a n-thpower distance law, is evaluated for high altitude platform station(HAPS W-CDMA systems. The downlink capacity using this model iscompared with the uplink capacity. It is shown that the uplink capacityis higher than the downlink capacity.
-
Polidori, A.; Tisopulos, L.; Pikelnaya, O.; Mellqvist, J.; Samuelsson, J.; Marianne, E.; Robinson, R. A.; Innocenti, F.; Finlayson, A.; Hashmonay, R.
2016-12-01
Despite great advances in reducing air pollution, the South Coast Air Basin (SCAB) still faces challenges to attain federal health standards for air quality. Refineries are large sources of ozone precursors and, hence contribute to the air quality problems of the region. Additionally, petrochemical facilities are also sources of other hazardous air pollutants (HAP) that adversely affect human health, for example aromatic hydrocarbons. In order to assure safe operation, decrease air pollution and minimize population exposure to HAP the South Coast Air Quality Management District (SCAQMD) has a number of regulations for petrochemical facilities. However, significant uncertainties still exist in emission estimates and traditional monitoring techniques often do not allow for real-time emission monitoring. In the fall of 2015 the SCAQMD, Fluxsense Inc., the National Physical Laboratory (NPL), and Atmosfir Optics Ltd. conducted a measurement study to characterize and quantify gaseous emissions from the tank farm of one of the largest oil refineries in the SCAB. Fluxsense used a vehicle equipped with Solar Occultation Flux (SOF), Differential Optical Absorption Spectroscopy (DOAS), and Extractive Fourier Transform Infrared (FTIR) spectroscopy instruments. Concurrently, NPL operated their Differential Absorption Lidar (DIAL) system. Both research groups quantified emissions from the entire tank farm and identified fugitive emission sources within the farm. At the same time, Atmosfir operated an Open Path FTIR (OP-FTIR) spectrometer along the fenceline of the tank farm. During this presentation we will discuss the results of the emission measurements from the tank farm of the petrochemical facility. Emission rates resulting from measurements by different ORS methods will be compared and discussed in detail.
-
40 CFR 71.5 - Permit applications.
2010-07-01
...) Emission criteria for regulated air pollutants, excluding hazardous air pollutants (HAP). Potential to emit...) Noncommercial food preparation; (F) Consumer use of office equipment and products; (G) Janitorial services and...) Emission criteria for HAP. Potential to emit of any HAP from any single emissions unit shall not exceed 1...
-
Update on the development of cotton gin PM10 emission factors for EPA's AP-42
A cotton ginning industry-supported project was initiated in 2008 to update the U.S. Environmental Protection Agency’s (EPA) Compilation of Air Pollution Emission Factors (AP-42) to include PM10 emission factors. This study develops emission factors from the PM10 emission factor data collected from ...
-
Time trend of polycyclic aromatic hydrocarbon emission factors from motor vehicles
Tao, Shu; Shen, Huizhong; Wang, Rong; Sun, Kang
2010-05-01
Motor vehicle is an important emission source of polycyclic aromatic hydrocarbons (PAHs) and this is particularly true in urban areas. Motor vehicle emission factors (EFs) for individual PAH compound reported in the literature varied for 4 to 5 orders of magnitude, leading to high uncertainty in emission estimation. In this study, the major factors affecting EFs were investigated and characterized by regression models. Based on the model developed, a motor vehicle PAH emission inventory at country level was developed. It was found that country and model year are the most important factors affecting EFs for PAHs. The influence of the two factors can be quantified by a single parameter of per capita gross domestic production (purchasing power parity), which was used as the independent variables of the regression models. The models developed using randomly selected 80% of measurements and tested with the remained data accounted for 28 to 48% of the variations in EFs for PAHs measured in 16 countries over 50 years. The regression coefficients of the EF prediction models were molecular weight dependent. Motor vehicle emission of PAHs from individual countries in the world in 1985, 1995, 2005, 2015, and 2025 were calculated and the global emission of total PAHs were 470, 390, and 430 Gg in 1985, 1995, and 2005 and will be 290 and 130 Gg in 2015 and 2025, respectively. The emission is currently passing its peak and will decrease due to significant decrease in China and other developing countries.
-
Determining size-specific emission factors for environmental tobacco smoke particles
Energy Technology Data Exchange (ETDEWEB)
Klepeis, Neil E.; Apte, Michael G.; Gundel, Lara A.; Sextro, Richard G.; Nazaroff, William W.
2002-07-07
Because size is a major controlling factor for indoor airborne particle behavior, human particle exposure assessments will benefit from improved knowledge of size-specific particle emissions. We report a method of inferring size-specific mass emission factors for indoor sources that makes use of an indoor aerosol dynamics model, measured particle concentration time series data, and an optimization routine. This approach provides--in addition to estimates of the emissions size distribution and integrated emission factors--estimates of deposition rate, an enhanced understanding of particle dynamics, and information about model performance. We applied the method to size-specific environmental tobacco smoke (ETS) particle concentrations measured every minute with an 8-channel optical particle counter (PMS-LASAIR; 0.1-2+ micrometer diameters) and every 10 or 30 min with a 34-channel differential mobility particle sizer (TSI-DMPS; 0.01-1+ micrometer diameters) after a single cigarette or cigar was machine-smoked inside a low air-exchange-rate 20 m{sup 3} chamber. The aerosol dynamics model provided good fits to observed concentrations when using optimized values of mass emission rate and deposition rate for each particle size range as input. Small discrepancies observed in the first 1-2 hours after smoking are likely due to the effect of particle evaporation, a process neglected by the model. Size-specific ETS particle emission factors were fit with log-normal distributions, yielding an average mass median diameter of 0.2 micrometers and an average geometric standard deviation of 2.3 with no systematic differences between cigars and cigarettes. The equivalent total particle emission rate, obtained integrating each size distribution, was 0.2-0.7 mg/min for cigars and 0.7-0.9 mg/min for cigarettes.
-
Directory of Open Access Journals (Sweden)
Murugesan Manoj
2015-02-01
Full Text Available Morphology controlled hydroxyapatite (HAp nanostructures play a vital role in biomedical engineering, tissue regenerative medicine, biosensors, chemotherapeutic applications, environmental remediation, etc. The present work investigates the influence of temperature, pH and time on the growth of HAp nanostructures using a simple, cost effective and surfactant free chemical approach. The obtained HAp nanostructures were systematically investigated by analytical techniques such as XRD, FESEM, EDX, FTIR and Raman spectroscopy. The XRD analysis showed that the hexagonal structure of the hydroxyapatite and average crystallite size was estimated from this analysis. The electron microscopic analysis confirmed the different morphologies obtained by varying the synthesis parameters such as temperature, pH and time. The elemental composition was determined through EDS analysis. FTIR and Raman spectroscopic analysis confirmed the presence of functional groups and the purity and crystallinity of the samples. The biocompatibility and adhesion nature of samples was examined with mouse preosteoblast cells. The obtained results demonstrated good biocompatibility and excellent focal adhesion.
-
DEFF Research Database (Denmark)
Yin, Jiaoyang; Vogel, Ulla Birgitte; Ma, Yegang
2009-01-01
-nucleotide polymorphisms (htSNPs) (rs238403, rs50871, rs3916840, rs238415, rs3916874 and rs1799787) from HapMap database were analyzed, which provide an almost complete coverage of the genetic variations in the ERCC2 gene. Although none of the six htSNPs was individually associated with lung cancer risk, we found that two...... ratio, OR (95% confidence interval, CI) = 2.62 (1.53–4.50), P = 0.0003 for hap4; OR (95% CI) = 3.01 (1.36–6.63), P = 0.004 for hap7]. Furthermore, diplotype analyses also strengthened the significant associations of risk haplotype 4 [OR (95% CI) = 3.56 (2.12–5.87), P
-
Estimating end-use emissions factors for policy analysis: the case of space cooling and heating.
Jacobsen, Grant D
2014-06-17
This paper provides the first estimates of end-use specific emissions factors, which are estimates of the amount of a pollutant that is emitted when a unit of electricity is generated to meet demand from a specific end-use. In particular, this paper provides estimates of emissions factors for space cooling and heating, which are two of the most significant end-uses. The analysis is based on a novel two-stage regression framework that estimates emissions factors that are specific to cooling or heating by exploiting variation in cooling and heating demand induced by weather variation. Heating is associated with similar or greater CO2 emissions factor than cooling in all regions. The difference is greatest in the Midwest and Northeast, where the estimated CO2 emissions factor for heating is more than 20% larger than the emissions factor for cooling. The minor differences in emissions factors in other regions, combined with the substantial difference in the demand pattern for cooling and heating, suggests that the use of overall regional emissions factors is reasonable for policy evaluations in certain locations. Accurately quantifying the emissions factors associated with different end-uses across regions will aid in designing improved energy and environmental policies.
-
The study on electromagnetic compatibility of DC electric motor in HAPS
Energy Technology Data Exchange (ETDEWEB)
Junping, Geng; Ronghong, Jin; Yu, Fan; Bo, Liu; Jiaqiang, Li; Yuebo, Cheng; Zhongyuan, Wang [Shanghai Jiao Tong Univ., Dpt. Electronic Engineering, Shanghai (China)
2005-10-01
The electromagnetic compatibility (EMC) problem of high altitude platform systems (HAPS) is investigated in this paper. A physical model for electromagnetic interferences (EMI) of electromagnetic radiation of spark discharge in DC electric motor is proposed. Based on this model, EMI frequency points has been estimated by approximative equation for the given structure and size of a motor, and EMI frequency points, peak values that received by the ports of antennas and far-field pattern have been calculated. The estimated results are consistent with the calculated ones. These frequency bands and spatial directions with max EMI should be avoided in the valid information when the HAPS system is being designed. Two methods are taken to shield electromagnetic radiation, either to mount a metal plate near the DC electric motor (EMI source), or to mount a perfect conductor board near the antenna array (sensitive element), are valid to shield electromagnetic radiation, but to mount a metal plate near the EMI source is more effective. (authors)
-
Influence of economic factors on future global emissions
International Nuclear Information System (INIS)
Duffey, R.B.; Poehnell, T.G.; Miller, A.I.; Tamm, J.A.
2001-01-01
The climate change debate is really about economics, and reducing greenhouse gas (GHG) emissions and climate change potential at a reasonable and acceptable cost for everyone. In this paper, we examine the major economic factors behind defining climate change policies that relate to reducing GHG emissions, and the value to be placed on CO 2 . We examine the impacts and the 'cost of carbon' based on the studies of GHG reduction strategies in the US and the European Union (EU). We show that a series of self-defeating assumptions have been used in the latest analyses regarding relative future energy and power costs, and hence future GHG emissions. We estimate: the 'natural value' of GHG emissions based on world economic factors, the value of electricity and energy based on world data, the cost advantage of using a given new technology, and the value of avoided GHG emissions in future global and national climate change projections. The use of electricity is shown to be key in aiding economic growth for the entire world. Using the latest Intergovernmental Panel on Climate Change (IPCC) 2000 climate change projections as a base, we reflect the impacts of differing energy prices on future global climate conditions and GHG reductions. We conduct a similar analysis for Canada using the latest 'Energy in Canada 2000' projections. We show how the use of advanced technology for the traditional production of electricity, and for hydrogen-based transportation fuels, can stabilize global emissions and assist in managing adverse climate change conditions without causing economic penalties. The method we develop is sufficiently general that it can be used for valuing the economic impact of the emission reductions for any technology. We estimate the embedded value and potential economic benefit of nuclear technology and electric contribution for both the world economy to 2100, and for the latest projections for Canada to 2020. (author)
-
Differentiation of nitrous oxide emission factors for agricultural soils
International Nuclear Information System (INIS)
Lesschen, Jan Peter; Velthof, Gerard L.; Vries, Wim de; Kros, Johannes
2011-01-01
Nitrous oxide (N 2 O) direct soil emissions from agriculture are often estimated using the default IPCC emission factor (EF) of 1%. However, a large variation in EFs exists due to differences in environment, crops and management. We developed an approach to determine N 2 O EFs that depend on N-input sources and environmental factors. The starting point of the method was a monitoring study in which an EF of 1% was found. The conditions of this experiment were set as the reference from which the effects of 16 sources of N input, three soil types, two land-use types and annual precipitation on the N 2 O EF were estimated. The derived EF inference scheme performed on average better than the default IPCC EF. The use of differentiated EFs, including different regional conditions, allows accounting for the effects of more mitigation measures and offers European countries a possibility to use a Tier 2 approach. - Highlights: → We developed an N 2 O emission factor inference scheme for agricultural soils. → This scheme accounts for different N-input sources and environmental conditions. → The derived EF inference scheme performed better than the default IPCC EF. → The use of differentiated EFs allows for better accounting of mitigation measures. - Emission factors for nitrous oxide from agricultural soils are derived as a function of N-input sources and environmental conditions on the basis of empirical information.
-
Directory of Open Access Journals (Sweden)
Barouch eGiechaskiel
2015-12-01
Full Text Available Emission inventories are used to quantify sources and identify trends in the emissions of air pollutants. They use vehicle-specific emission factors that are typically determined in the laboratory, through remote-sensing, vehicle chasing experiments and, more recently, on-board Portable Emission Measurement Systems (PEMS. Although PEMS is widely applied to measure gaseous pollutants, their application to Solid Particle Number (SPN emissions is new. In this paper, we discuss the current status of determining SPN emission factors both on the chassis dynamometer and on-road using PEMS-SPN. First, we determine the influence of the measurement equipment, ambient temperature, driving style and cycle characteristics, and the extra mass of the PEMS equipment on the SPN emissions. Afterward, we present the SPN emissions under type-approval conditions as well as on the road of two heavy-duty diesel vehicles equipped with Diesel Particulate Filter (DPF (one Euro VI, two light-duty diesel vehicles equipped with DPF, one light-duty vehicle equipped with a Port Fuel Injection engine (PFI, and seven Gasoline Direct Injection (GDI passenger cars (two Euro 6. We find that cold-start and strong accelerations tend to substantially increase SPN emissions. The two heavy-duty vehicles showed emissions around 2×10^13 p/km (Euro V truck and 6×10^10 p/km (Euro VI truck, respectively. One of the DPF-equipped light-duty vehicles showed emissions of 8×10^11 p/km, while the other one had one order of magnitude lower emissions. The PFI car had SPN emissions slightly higher than 1×10^12 p/km. The emissions of GDI cars spanned approximately from 8×10^11 p/km to 8×10^12 p/km. For the cars without DPF, the SPN emissions remained within a factor of two of the laboratory results. This factor was on average around 0.8 for the Euro 6 and 1.6 for the Euro 5 GDIs. The DPF equipped vehicles showed a difference of almost one order of magnitude between laboratory and on-road tests
-
Small-Chamber Measurements of Chemical-Specific Emission Factors for Drywall
Energy Technology Data Exchange (ETDEWEB)
Maddalena, Randy; Russell, Marion; Apte, Michael G.
2010-06-01
Imported drywall installed in U.S. homes is suspected of being a source of odorous and potentially corrosive indoor pollutants. To support an investigation of those building materials by the Consumer Products Safety Commission (CPSC), Lawrence Berkeley National Laboratory (LBNL) measured chemical-specific emission factors for 30 samples of drywall materials. Emission factors are reported for 75 chemicals and 30 different drywall samples encompassing both domestic and imported stock and incorporating natural, synthetic, or mixed gypsum core material. CPSC supplied all drywall materials. First the drywall samples were isolated and conditioned in dedicated chambers, then they were transferred to small chambers where emission testing was performed. Four sampling and analysis methods were utilized to assess (1) volatile organic compounds, (2) low molecular weight carbonyls, (3) volatile sulfur compounds, and (4) reactive sulfur gases. LBNL developed a new method that combines the use of solid phase microextraction (SPME) with small emission chambers to measure the reactive sulfur gases, then extended that technique to measure the full suite of volatile sulfur compounds. The testing procedure and analysis methods are described in detail herein. Emission factors were measured under a single set of controlled environmental conditions. The results are compared graphically for each method and in detailed tables for use in estimating indoor exposure concentrations.
-
Wolf, Julie; Asrar, Ghassem R; West, Tristram O
2017-09-29
Livestock play an important role in carbon cycling through consumption of biomass and emissions of methane. Recent research suggests that existing bottom-up inventories of livestock methane emissions in the US, such as those made using 2006 IPCC Tier 1 livestock emissions factors, are too low. This may be due to outdated information used to develop these emissions factors. In this study, we update information for cattle and swine by region, based on reported recent changes in animal body mass, feed quality and quantity, milk productivity, and management of animals and manure. We then use this updated information to calculate new livestock methane emissions factors for enteric fermentation in cattle, and for manure management in cattle and swine. Using the new emissions factors, we estimate global livestock emissions of 119.1 ± 18.2 Tg methane in 2011; this quantity is 11% greater than that obtained using the IPCC 2006 emissions factors, encompassing an 8.4% increase in enteric fermentation methane, a 36.7% increase in manure management methane, and notable variability among regions and sources. For example, revised manure management methane emissions for 2011 in the US increased by 71.8%. For years through 2013, we present (a) annual livestock methane emissions, (b) complete annual livestock carbon budgets, including carbon dioxide emissions, and (c) spatial distributions of livestock methane and other carbon fluxes, downscaled to 0.05 × 0.05 degree resolution. Our revised bottom-up estimates of global livestock methane emissions are comparable to recently reported top-down global estimates for recent years, and account for a significant part of the increase in annual methane emissions since 2007. Our results suggest that livestock methane emissions, while not the dominant overall source of global methane emissions, may be a major contributor to the observed annual emissions increases over the 2000s to 2010s. Differences at regional and local scales may help
-
Energy Technology Data Exchange (ETDEWEB)
Wolf, Julie; Asrar, Ghassem R.; West, Tristram O.
2017-09-29
Background: Livestock play an important role in carbon cycling through consumption of biomass and emissions of methane. Recent research suggests that existing bottom-up inventories of livestock methane emissions in the US, such as those made using 2006 IPCC Tier 1 livestock emissions factors, are too low. This may be due to outdated information used to develop these emissions factors. In this study, we update information for cattle and swine by region, based on reported recent changes in animal body mass, feed quality and quantity, milk productivity, and management of animals and manure. We then use this updated information to calculate new livestock methane emissions factors for enteric fermentation in cattle, and for manure management in cattle and swine.
-
An Evaluation of Interference Mitigation Schemes for HAPS Systems
Directory of Open Access Journals (Sweden)
Nam Kim
2008-07-01
Full Text Available The International Telecommunication Union-Radiocommunication sector (ITU-R has conducted frequency sharing studies between fixed services (FSs using a high altitude platform station (HAPS and fixed-satellite services (FSSs. In particular, ITU-R has investigated the power limitations related to HAPS user terminals (HUTs to facilitate frequency sharing with space station receivers. To reduce the level of interference from the HUTs that can harm a geostationary earth orbit (GEO satellite receiver in a space station, previous studies have taken two approaches: frequency sharing using a separated distance (FSSD and frequency sharing using power control (FSPC. In this paper, various performance evaluation results of interference mitigation schemes are presented. The results include performance evaluations using a new interference mitigation approach as well as conventional approaches. An adaptive beamforming scheme (ABS is introduced as a new scheme for efficient frequency sharing, and the interference mitigation effect on the ABS is examined considering pointing mismatch errors. The results confirm that the application of ABS enables frequency sharing between two systems with a smaller power reduction of HUTs in a cocoverage area compared to this reduction when conventional schemes are utilized. In addition, the analysis results provide the proper amount of modification at the transmitting power level of the HUT required for the suitable frequency sharing.
-
Gamma irradiation of melt processed biomedical PDLLA/HAP nanocomposites
International Nuclear Information System (INIS)
Dadbin, Susan; Kheirkhah, Yahya
2014-01-01
Poly(D-L lactide) PDLLA/hydroxyapatite (HAP) nanocomposites at various compositions were prepared by melt-compounding process and then subjected to gamma irradiation at a dose of 30 kGy. The morphology of the nanocomposites, characterized by transmission electron microscopy (TEM), displayed HAP nanoparticles at various sizes ranging from 10 to 100 nm distributed almost evenly within the polymer matrix. Differential scanning calorimetric (DSC) analysis of the irradiated nanocomposites showed an increase in the degree of crystallinity along with a melting peak split. The double melting peak suggested formation of different crystalline structures in the radiation exposed nanocomposites. Also the cold crystallization peak shifted to lower temperatures and became much sharper upon irradiation, indicating higher crystallization rate. The irradiated nanocomposites showed lower tensile strength and elongation at break, suggesting occurrence of some chain scission reactions in the PLA. - Highlights: • Biomedical polylactic acid/hydroxyapatite nanocomposites prepared by melt-compounding were gamma irradiated. • Transmission electron microscopy showed hydroxyapatite nanoparticles evenly distributed within polylactic acid ranging from 10 to 100 nm. • A halo appeared around hydroxyapatite particles showing interfacial interactions between polylactic acid and the particles. • Double melting peak appeared for polylactic acid in DSC thermograms upon gamma irradiation of the nanocomposites
-
Directory of Open Access Journals (Sweden)
Abo Ryan
2010-12-01
Full Text Available Abstract Background In candidate-gene association studies of single nucleotide polymorphisms (SNPs, multilocus analyses are frequently of high dimensionality when considering haplotypes or haplotype pairs (diplotypes and differing modes of expression. Often, while candidate genes are selected based on their biological involvement in a given pathway, little is known about the functionality of SNPs to guide association studies. Investigators face the challenge of exploring multiple SNP models to elucidate which variants, independently or in combination, might be associated with a disease of interest. A data mining module, hapConstructor (freely-available in Genie software performs systematic construction and association testing of multilocus genotype data in a Monte Carlo framework. Our objective was to assess its utility to guide statistical analyses of haplotypes within a candidate region (or combined genotypes across candidate genes beyond that offered by a standard logistic regression approach. Methods We applied the hapConstructor method to a multilocus investigation of candidate genes involved in pro-inflammatory cytokine IL6 production, IKBKB, IL6, and NFKB1 (16 SNPs total hypothesized to operate together to alter colorectal cancer risk. Data come from two U.S. multicenter studies, one of colon cancer (1,556 cases and 1,956 matched controls and one of rectal cancer (754 cases and 959 matched controls. Results HapConstrcutor enabled us to identify important associations that were further analyzed in logistic regression models to simultaneously adjust for confounders. The most significant finding (nominal P = 0.0004; false discovery rate q = 0.037 was a combined genotype association across IKBKB SNP rs5029748 (1 or 2 variant alleles, IL6 rs1800797 (1 or 2 variant alleles, and NFKB1 rs4648110 (2 variant alleles which conferred an ~80% decreased risk of colon cancer. Conclusions Strengths of hapConstructor were: systematic identification of
-
Real-time black carbon emission factor measurements from light duty vehicles.
Forestieri, Sara D; Collier, Sonya; Kuwayama, Toshihiro; Zhang, Qi; Kleeman, Michael J; Cappa, Christopher D
2013-11-19
Eight light-duty gasoline low emission vehicles (LEV I) were tested on a Chassis dynamometer using the California Unified Cycle (UC) at the Haagen-Smit vehicle test facility at the California Air Resources Board in El Monte, CA during September 2011. The UC includes a cold start phase followed by a hot stabilized running phase. In addition, a light-duty gasoline LEV vehicle and ultralow emission vehicle (ULEV), and a light-duty diesel passenger vehicle and gasoline direct injection (GDI) vehicle were tested on a constant velocity driving cycle. A variety of instruments with response times ≥0.1 Hz were used to characterize how the emissions of the major particulate matter components varied for the LEVs during a typical driving cycle. This study focuses primarily on emissions of black carbon (BC). These measurements allowed for the determination of BC emission factors throughout the driving cycle, providing insights into the temporal variability of BC emission factors during different phases of a typical driving cycle.
-
Factors influencing CO2 emissions in China's power industry: Co-integration analysis
International Nuclear Information System (INIS)
Zhao, Xiaoli; Ma, Qian; Yang, Rui
2013-01-01
More than 40% of China's total CO 2 emissions originate from the power industry. The realization of energy saving and emission reduction within China's power industry is therefore crucial in order to achieve CO 2 emissions reduction in this country. This paper applies the autoregressive-distributed lag (ARDL) co-integration model to study the major factors which have influenced CO 2 emissions within China's power industry from 1980 to 2010. Results have shown that CO 2 emissions from China's power industry have been increasing rapidly. From 1980 to 2010, the average annual growth rate was 8.5%, and the average growth rate since 2002 has amounted to 10.5%. Secondly, the equipment utilization hour (as an indicator of the power demand) has the greatest influence on CO 2 emissions within China's power industry. In addition, the impact of the industrial added value of the power sector on CO 2 emissions is also positive from a short-term perspective. Thirdly, the Granger causality results imply that one of the important motivators behind China's technological progress, within the power industry, originates from the pressures created by a desire for CO 2 emissions reduction. Finally, this paper provides policy recommendations for energy saving and emission reduction for China's power industry. - Highlights: ► We study the major factors influencing China's power industry CO 2 emissions. ► The average annual growth rate of CO 2 emission from power industry is calculated. ► Installed capacity has the greatest influence on power industry CO 2 emission. ► The Granger causality between CO 2 emission and its effecting factors is analyzed
-
DEMONSTRATION OF A NO-VOC/NO-HAP WOOD KITCHEN CABINET COATING SYSTEM
The report gives results of the development and demonstration of a no-VOC (volatile organic compound)/no-HAP (hazardous air pollutant) wood furniture coating system at two cabinet manufacturing plants: one in Portland, OR, and the other in Redwood City, CA. Technology transfer ef...
-
Analysis of regional difference on impact factors of China’s energy – Related CO2 emissions
International Nuclear Information System (INIS)
Li, Huanan; Mu, Hailin; Zhang, Ming; Gui, Shusen
2012-01-01
With the intensification of global warming, the issue of carbon emissions causes more and more attention in recent years. In this paper, China’s 30 provincial-level administrative units are divided into five emission regions according to the annual average value of provincial CO 2 emissions per capita during 1990 and 2010. The regional differences in impact factors on CO 2 emissions are discussed using STIRPAT (stochastic impacts by regression on population, affluence, and technology) model. The results indicate that although GDP (Gross domestic product) per capita, industrial structure, population, urbanization and technology level have different impacts on CO 2 emissions in different emission regions, they are almost always the main factors in all emission regions. In most emission regions, urbanization and GDP per capita has a bigger impact on CO 2 emissions than other factors. Improving technology level produces a small reduction in CO 2 emissions in most emission regions, but it is still a primary way for CO 2 reduction in China. It’s noteworthy that industrial structure isn’t the main factor and improving technology level increases CO 2 emissions in high emission region. Different measures should be adopted for CO 2 reductions according to local conditions in different regions. -- Highlights: ► Regional differences of the impact factors on China’s CO 2 emissions are analyzed. ► Five macro factors like GDP per capita are almost always main influence factors in all regions. ► The impacts of different factors are different. ► Improving technology has no significant reduction on CO 2 emission in most regions. ► Policy on CO 2 reduction should be adapted to local conditions.
-
International Nuclear Information System (INIS)
Sugiura, Takeyuki; Yamaguchi, Aya; Miyamoto, Kentaro
2008-01-01
RNF43 is a recently discovered RING finger protein that is implicated in colon cancer pathogenesis. This protein possesses growth-promoting activity but its mechanism remains unknown. In this study, to gain insight into the biological action of RNF43 we characterized it biochemically and intracellularly. A combination of indirect immunofluorescence analysis and biochemical fractionation experiments suggests that RNF43 resides in the endoplasmic reticulum (ER) as well as in the nuclear envelope. Sucrose density gradient fractionation demonstrates that RNF43 co-exists with emerin, a representative inner nuclear membrane protein in the nuclear subcompartment. The cell-free system with pure components reveals that recombinant RNF43 fused with maltose-binding protein has autoubiquitylation activity. By the yeast two-hybrid screening we identified HAP95, a chromatin-associated protein interfacing the nuclear envelope, as an RNF43-interacting protein and substantiated this interaction in intact cells by the co-immunoprecipitation experiments. HAP95 is ubiquitylated and subjected to a proteasome-dependent degradation pathway, however, the experiments in which 293 cells expressing both RNF43 and HAP95 were treated with a proteasome inhibitor, MG132, show that HAP95 is unlikely to serve as a substrate of RNF43 ubiquitin ligase. These results infer that RNF43 is a resident protein of the ER and, at least partially, the nuclear membrane, with ubiquitin ligase activity and may be involved in cell growth control potentially through the interaction with HAP95
-
Zhang, F.; Chen, Y.; Tian, C.; Li, J.; Zhang, G.; Matthias, V.
2015-09-01
Shipping emissions have significant influence on atmospheric environment as well as human health, especially in coastal areas and the harbor districts. However, the contribution of shipping emissions on the environment in China still need to be clarified especially based on measurement data, with the large number ownership of vessels and the rapid developments of ports, international trade and shipbuilding industry. Pollutants in the gaseous phase (carbon monoxide, sulfur dioxide, nitrogen oxides, total volatile organic compounds) and particle phase (particulate matter, organic carbon, elemental carbon, sulfates, nitrate, ammonia, metals) in the exhaust from three different diesel engine power offshore vessels in China were measured in this study. Concentrations, fuel-based and power-based emissions factors for various operating modes as well as the impact of engine speed on emissions were determined. Observed concentrations and emissions factors for carbon monoxide, nitrogen oxides, total volatile organic compounds, and particulate matter were higher for the low engine power vessel than for the two higher engine power vessels. Fuel-based average emissions factors for all pollutants except sulfur dioxide in the low engine power engineering vessel were significantly higher than that of the previous studies, while for the two higher engine power vessels, the fuel-based average emissions factors for all pollutants were comparable to the results of the previous studies. The fuel-based average emissions factor for nitrogen oxides for the small engine power vessel was more than twice the International Maritime Organization standard, while those for the other two vessels were below the standard. Emissions factors for all three vessels were significantly different during different operating modes. Organic carbon and elemental carbon were the main components of particulate matter, while water-soluble ions and elements were present in trace amounts. Best-fit engine speeds
-
International Nuclear Information System (INIS)
Milicevic, D.; Trifunovic, S.; Dojcilovic, J.; Ignjatovic, N.; Suljovrujic, E.
2010-01-01
The influence of gamma radiation on the molecular weight and glass transition behaviour of poly-L-lactide (PLLA) and hydroxyapatite/poly-L-lactide (HAp/PLLA) nanocomposite has been studied. Since PLLA exposed to high-energy radiation in the presence of air is prone to chain scission reactions and large degradation, changes in molecular weight were obtained by gel permeation chromatography (GPC). Alterations in the glass transition behaviour were investigated by differential scanning calorimetry (DSC). The apparent activation energy (ΔH*) for glass transition was determined on the basis of the heating rate dependence of the glass transition temperature (T g ). Our findings support the fact that chain scission is the main reason for the decrease of T g and ΔH* with the absorbed dose. Furthermore, more intensive chain scission degradation of PLLA was observed in HAp/PLLA and can only be ascribed to the presence of HAp nanoparticles. Consequently, initial differences in the glass transition temperature and/or apparent activation energy of PLLA and HAp/PLLA became more pronounced with absorbed dose. This study reveals that radiation-induced changes in molecular weight and glass transition temperature occur in a predictable and fairly accurate manner. Therefore, gamma radiation can be used not only for sterilization but also for tailoring desirable end-use properties of these biomaterials.
-
An Evaluation of Interference Mitigation Schemes for HAPS Systems
Directory of Open Access Journals (Sweden)
Kim Nam
2008-01-01
Full Text Available Abstract The International Telecommunication Union-Radiocommunication sector (ITU-R has conducted frequency sharing studies between fixed services (FSs using a high altitude platform station (HAPS and fixed-satellite services (FSSs. In particular, ITU-R has investigated the power limitations related to HAPS user terminals (HUTs to facilitate frequency sharing with space station receivers. To reduce the level of interference from the HUTs that can harm a geostationary earth orbit (GEO satellite receiver in a space station, previous studies have taken two approaches: frequency sharing using a separated distance (FSSD and frequency sharing using power control (FSPC. In this paper, various performance evaluation results of interference mitigation schemes are presented. The results include performance evaluations using a new interference mitigation approach as well as conventional approaches. An adaptive beamforming scheme (ABS is introduced as a new scheme for efficient frequency sharing, and the interference mitigation effect on the ABS is examined considering pointing mismatch errors. The results confirm that the application of ABS enables frequency sharing between two systems with a smaller power reduction of HUTs in a cocoverage area compared to this reduction when conventional schemes are utilized. In addition, the analysis results provide the proper amount of modification at the transmitting power level of the HUT required for the suitable frequency sharing.
-
Energy Technology Data Exchange (ETDEWEB)
Sasaki, Kenkichi; Kamitakahara, Masanobu; Ioku, Koji [Graduate School of Environmental Studies, Tohoku University, Aoba 6-6-20, Aramaki, Aoba-ku, Sendai 980-8579 (Japan); Oyane, Ayako [Nanosystem Research Institute, National Institute of Advanced Industrial Science and Technology (AIST), Central 4, 1-1-1 Higashi, Tsukuba, Ibaraki 305-8562 (Japan); Hyodo, Koji [Human Technology Research Institute, National Institute of Advanced Industrial Science and Technology (AIST), 1-2-1 Namiki, Tsukuba, Ibaraki 305-8564 (Japan); Ito, Atsuo; Sogo, Yu, E-mail: a-oyane@aist.go.j [Human Technology Research Institute, National Institute of Advanced Industrial Science and Technology (AIST), Central 6, 1-1-1, Higashi, Tsukuba, Ibaraki 305-8566 (Japan)
2010-12-15
A polymeric percutaneous device with good biocompatibility and resistance to bacterial infection is required clinically. In this study, a fibroblast growth factor-2 (FGF-2)-hydroxyapatite (HAp) composite layer (FHAp layer) was formed on the surfaces of ethylene-vinyl alcohol copolymer (EVOH) specimens using a coating process in a supersaturated calcium phosphate solution supplemented with FGF-2. FGF-2 in the FHAp layer retained its biological activity to promote proliferation of fibroblasts. The EVOH specimens coated with HAp and FHAp layers were percutaneously implanted in the scalp of rats. Not only the HAp layer but also the FHAp layer showed good biocompatibility, and FGF-2 showed no harmful effects on the skin tissue responses to the implanted specimen as long as 14 d. No significantly higher infection resistance was verified for the FHAp layer over the HAp layer, although an FHAp layer coated on a metallic percutaneous device for bone fixation demonstrated higher resistance to bacterial infection over an HAp layer in the previous study. The efficacy of FHAp layers coated on percutaneous implants in resistance to bacterial infection depends on physical factors including fixation condition, stiffness and movement of implants.
-
Measurements of air pollution emission factors for marine transportation in SECA
Directory of Open Access Journals (Sweden)
B. Alföldy
2013-07-01
Full Text Available The chemical composition of the plumes of seagoing ships was measured during a two week long measurement campaign in the port of Rotterdam, Hoek van Holland The Netherlands, in September 2009. Altogether, 497 ships were monitored and a statistical evaluation of emission factors (g kg−1 fuel was provided. The concerned main atmospheric components were SO2, NO2, NOx and the aerosol particle number. In addition, the elemental and water-soluble ionic composition of the emitted particulate matter was determined. Emission factors were expressed as a function of ship type, power and crankshaft rotational speed. The average SO2 emission factor was found to be roughly half of what is allowed in sulphur emission control areas (16 vs. 30 g kg−1 fuel, and exceedances of this limit were rarely registered. A significant linear relationship was observed between the SO2 and particle number emission factors. The intercept of the regression line, 4.8 × 1015 (kg fuel−1, gives the average number of particles formed during the burning of 1 kg zero sulphur content fuel, while the slope, 2 × 1018, provides the average number of particles formed with 1 kg sulphur burnt with the fuel. Water-soluble ionic composition analysis of the aerosol samples from the plumes showed that ~144 g of particulate sulphate was emitted from 1 kg sulphur burnt with the fuel. The mass median diameter of sulphate particles estimated from the measurements was ~42 nm.
-
Goldberg, J A; Bradnam, M S; Kerr, D J; McKillop, J H; Bessent, R G; McArdle, C S; Willmott, N; George, W D
1987-12-01
As intra-arterial chemotherapy for liver metastases of colorectal origin becomes accepted, methods of further improving drug delivery to the tumour have been devised. Degradable microspheres have been shown to reduce regional blood flow by transient arteriolar capillary block, thereby improving uptake of a co-administered drug, when injected into the hepatic artery. In our study of five patients, we combined hepatic arterial perfusion scintigraphy (HAPS) and SPECT to assess the localization of approximately 1 X 10(5) labelled microspheres of human serum albumin (99Tcm MSA) in tumour. In addition, in three patients, we assessed the effect of an intra-arterial infusion of the vasoactive agent angiotension II during HAPS. Results were interpreted by comparing transaxial slices with corresponding slices of a tin colloid liver-spleen scan. Two of five patients showed good localization of 99Tcm MSA in tumour without an angiotensin II infusion. Of the three patients receiving angiotensin II, all showed good tumour targetting with the vasoconstrictor compared with only one of these three before its use. Thus, hepatic arterial infusion of angiotensin II greatly improves microsphere localization in tumour in some patients with colorectal liver metastases. This technique may be useful in the assessment of tumour targetting before and during locoregional therapy.
-
Analysis on influence factors of China's CO2 emissions based on Path-STIRPAT model
International Nuclear Information System (INIS)
Li Huanan; Mu Hailin; Zhang Ming; Li Nan
2011-01-01
With the intensification of global warming and continued growth in energy consumption, China is facing increasing pressure to cut its CO 2 (carbon dioxide) emissions down. This paper discusses the driving forces influencing China's CO 2 emissions based on Path-STIRPAT model-a method combining Path analysis with STIRPAT (stochastic impacts by regression on population, affluence and technology) model. The analysis shows that GDP per capita (A), industrial structure (IS), population (P), urbanization level (R) and technology level (T) are the main factors influencing China's CO 2 emissions, which exert an influence interactively and collaboratively. The sequence of the size of factors' direct influence on China's CO 2 emission is A>T>P>R>IS, while that of factors' total influence is A>R>P>T>IS. One percent increase in A, IS, P, R and T leads to 0.44, 1.58, 1.31, 1.12 and -1.09 percentage change in CO 2 emission totally, where their direct contribution is 0.45, 0.07, 0.63, 0.08, 0.92, respectively. Improving T is the most important way for CO 2 reduction in China. - Highlights: → We analyze the driving forces influencing China's CO 2 emissions. → Five macro factors like per capita GDP are the main influencing factors. → These factors exert an influence interactively and collaboratively. → Different factors' direct and total influence on China's CO 2 emission is different. → Improving technology level is the most important way for CO 2 reduction in China.
-
Englander, J.; Brandt, A. R.
2017-12-01
There has been numerous studies in quantifying the scale of fugitive emissions from across the natural gas value chain. These studies have typically focused on either specific types of equipment (such as valves) or on a single part of the life-cycle of natural gas production (such as gathering stations).1,2 However it has been demonstrated that average emissions factors are not sufficient for representing leaks in the natural gas system.3 In this work, we develop a robust estimate of fugitive emissions rates by incorporating all publicly available studies done at the component up to the process level. From these known studies, we create a database of leaks with normalized nomenclature from which leak estimates can be drawn from actual leak observations. From this database, and parameterized by meta-data such as location, scale of study, or placement in the life-cycle, we construct stochastic emissions factors specific for each process unit. This will be an integrated tool as part of the Oil production greenhouse gas estimator (OPGEE) as well as the Fugitive Emissions Abatement Simulation Toolkit (FEAST) models to enhances their treatment of venting and fugitive emissions, and will be flexible to include user provided data and input parameters.4,51. Thoma, ED et al. Assessment of Uinta Basin Oil and Natural Gas Well Pad Pneumatic Controller Emissions. J. Environ. Prot. 2017. 2. Marchese, AJ et al. Methane Emissions from United States Natural Gas Gathering and Processing. ES&T 2015. doi:10.1021/acs.est.5b02275 3. Brandt, AR et al. Methane Leaks from Natural Gas Systems Follow Extreme Distributions. ES&T 2016. doi:10.1021/acs.est.6b04303 4. El-Houjeiri, HM et al. An open-source LCA tool estimating greenhouse gas emissions from crude oil production using field characteristics. ES&T 2013. doi: 10.1021/es304570m 5. Kemp, CE et al. Comparing Natural Gas Leakage Detection Technologies Using an Open-Source `Virtual Gas Field' Simulator. ES&T 2016. doi:10.1021/acs.est.5b
-
Tailpipe, resuspended road dust, and brake-wear emission factors from on-road vehicles
Abu-Allaban, Mahmoud; Gillies, John A.; Gertler, Alan W.; Clayton, Russ; Proffitt, David
Intensive mass and chemical measurements were performed at roadside locations in Reno, Nevada, and Durham/Research Triangle Park), North Carolina to derive tailpipe, resuspended road dust, and brake-wear emission factors from in-use vehicles. Continuous particulate matter (PM) data were utilized to derive total emission factors while integrated PM data were used to attribute the calculated emission factors to different mechanisms using chemical mass balance receptor modeling and scanning electron microscopy techniques. Resuspended road dust and tailpipe emissions were found to be the dominant mechanisms that contribute significantly to the total PM 10 and PM 2.5 emission factors, respectively. Small contributions from brake-wear were observed at locations where strong braking occurs, but no tire-wear was seen at any sampling location. PM 10 emission rates from light-duty spark ignition (LDSI) vehicles ranged from 40 to 780 mg/km, 10 to 70 mg/km, and 0 to 80 mg/km per vehicle for road dust, tailpipe, and brake-wear, respectively. PM 10 emission rates from heavy-duty vehicles ranged from 230 to 7800 mg/km, 60 to 570 mg/km, and 0 to 610 mg/km per vehicle for road dust, tailpipe, and brake-wear, respectively. PM 2.5 emission rates from LDSI vehicles ranged from 2 to 25 mg/km, 10 to 50 mg/km, and 0 to 5 mg/km per vehicle for road dust, tailpipe, and brake-wear, respectively. PM 2.5 emission rates from heavy-duty vehicles ranged from 15 to 300 mg/km, 60 to 480 mg/km, and 0 to 15 mg/km per vehicle for road dust, tailpipe, and brake-wear, respectively.
-
Performance simulation in high altitude platforms (HAPs) communications systems
Ulloa-Vásquez, Fernando; Delgado-Penin, J. A.
2002-07-01
This paper considers the analysis by simulation of a digital narrowband communication system for an scenario which consists of a High-Altitude aeronautical Platform (HAP) and fixed/mobile terrestrial transceivers. The aeronautical channel is modelled considering geometrical (angle of elevation vs. horizontal distance of the terrestrial reflectors) and statistical arguments and under these circumstances a serial concatenated coded digital transmission is analysed for several hypothesis related to radio-electric coverage areas. The results indicate a good feasibility for the communication system proposed and analysed.
-
Wang, Jonathan M.; Jeong, Cheol-Heon; Zimmerman, Naomi; Healy, Robert M.; Evans, Greg J.
2018-07-01
Temporal variations of vehicle emissions are affected by various compounding factors in the real world. The focus of this study is to determine the effects of ambient conditions and post-tailpipe changes on traffic emissions measured in the near-road region. Emission factors allowed for the isolation of the traffic signal and accounted for effects of local meteorology and dilution. Five month-long measurement campaigns were conducted at an urban near-road site that exhibited a broad range of ambient conditions with temperatures ranging between -18 and +30 °C. Particle number emission factors were 2.0× higher in the winter relative to the summer, which was attributed to changes in particles post-tailpipe. Conversely, toluene emissions were 2.5× higher in the summer relative to the winter, attributed to changes in fuel composition. Diurnal trends of emission factors showed substantial increases in emissions during the morning rush hour for black carbon (1.9×), particle number (2.4×), and particle-bound polycyclic aromatic hydrocarbons (3.0×), affected by fleet make-up. In contrast, particle number emission factors were highest midday with mean values 3.7× higher than at night. This midday increase was attributed to particle formation or growth from local traffic emissions and showed different wind direction dependence than regional events.
-
40 CFR Table 2 to Subpart Mmm of... - Standards for New and Existing PAI Sources
2010-07-01
... mass emissions criteria that have gaseous organic HAP emissions controlled to less than 90% on or after November 10, 1997 98% gaseous organic HAP control per vent or ≤20 ppmv TOC outlet limit. New: Processes... a HAP Particulate matter concentration not to exceed 0.01 gr/dscf. Heat exchange systems Each heat...
-
Energy Technology Data Exchange (ETDEWEB)
Shen, Guofeng [Jiangsu Academy of Environmental Science, Nanjing (China). Inst. of Atmospheric Sciences
2014-07-01
Emission inventory is basic for the understanding of environmental behaviors and potential effects of compounds, however, current inventories are often associated with relatively high uncertainties. One important reason is the lack of emission factors, especially for the residential solid fuel combustion in developing countries. In the present study, emission factors of a group of pollutants including particulate matter, organic carbon, elemental carbon (sometimes known as black carbon) and polycyclic aromatic hydrocarbons were measured for a variety of residential solid fuels including coal, crop straw, wood, and biomass pellets in rural China. The study provided a large number of emission factors that can be further used in emission estimation. Composition profiles and isomer ratios were investigated and compared so as to be used in source apportionment. In addition, the present study identified and quantified the influence of factors like fuel moisture, volatile matter on emission performance.
-
Evaluation of life-cycle air emission factors of freight transportation.
Facanha, Cristiano; Horvath, Arpad
2007-10-15
Life-cycle air emission factors associated with road, rail, and air transportation of freight in the United States are analyzed. All life-cycle phases of vehicles, infrastructure, and fuels are accounted for in a hybrid life-cycle assessment (LCA). It includes not only fuel combustion, but also emissions from vehicle manufacturing, maintenance, and end of life, infrastructure construction, operation, maintenance, and end of life, and petroleum exploration, refining, and fuel distribution. Results indicate that total life-cycle emissions of freight transportation modes are underestimated if only tailpipe emissions are accounted for. In the case of CO2 and NOx, tailpipe emissions underestimate total emissions by up to 38%, depending on the mode. Total life-cycle emissions of CO and SO2 are up to seven times higher than tailpipe emissions. Sensitivity analysis considers the effects of vehicle type, geography, and mode efficiency on the final results. Policy implications of this analysis are also discussed. For example, while it is widely assumed that currently proposed regulations will result in substantial reductions in emissions, we find that this is true for NOx, emissions, because fuel combustion is the main cause, and to a lesser extent for SO2, but not for PM10 emissions, which are significantly affected by the other life-cycle phases.
-
Fachinger, Friederike; Drewnick, Frank; Gieré, Reto; Borrmann, Stephan
2017-06-01
For a common household wood stove and a pellet stove we investigated the dependence of emission factors for various gaseous and particulate pollutants on burning phase, burning condition, and fuel. Ideal and non-ideal burning conditions (dried wood, under- and overload, small logs, logs with bark, excess air) were used. We tested 11 hardwood species (apple, ash, bangkirai, birch, beech, cherry, hickory, oak, olive, plum, sugar maple), 4 softwood species (Douglas fir, pine, spruce, spruce/fir), treated softwood, beech and oak wood briquettes, paper briquettes, brown coal, wood chips, and herbaceous species (miscanthus, Chinese silver grass) as fuel. Particle composition (black carbon, non-refractory, and some semi-refractory species) was measured continuously. Repeatability was shown to be better for the pellet stove than for the wood stove. It was shown that the user has a strong influence on wood stove emission behavior both by selection of the fuel and of the burning conditions: Combustion efficiency was found to be low at both very low and very high burn rates, and influenced particle properties such as particle number, mass, and organic content in a complex way. No marked differences were found for the emissions from different wood species. For non-woody fuels, much higher emission factors could be observed (up to five-fold increase). Strongest enhancement of emission factors was found for burning of small or dried logs (up to six-fold), and usage of excess air (two- to three-fold). Real world pellet stove emissions can be expected to be much closer to laboratory-derived emission factors than wood stove emissions, due to lower dependence on user operation.
-
HapHop-Physio: a computer game to support cognitive therapies in children
Directory of Open Access Journals (Sweden)
Rico-Olarte C
2017-07-01
Full Text Available Carolina Rico-Olarte,1 Diego M López,1 Santiago Narváez,1 Charic D Farinango,1 Peter S Pharow2 1Faculty of Electronics and Telecommunications Engineering, Universidad del Cauca, Telematics Engineering Research Group, Popayán, Colombia; 2Fraunhofer Institute of Digital Media and Technology IDMT, Ilmenau, Germany Background: Care and support of children with physical or mental disabilities are accompanied with serious concerns for parents, families, healthcare institutions, schools, and their communities. Recent studies and technological innovations have demonstrated the feasibility of providing therapy and rehabilitation services to children supported by computer games. Objective: The aim of this paper is to present HapHop-Physio, an innovative computer game that combines exercise with fun and learning, developed to support cognitive therapies in children. Methods: Conventional software engineering methods such as the Scrum methodology, a functionality test and a related usability test, were part of the comprehensive methodology adapted to develop HapHop-Physio. Results: The game supports visual and auditory attention therapies, as well as visual and auditory memory activities. The game was developed by a multidisciplinary team, which was based on the Hopscotch® platform provided by Fraunhofer Institute for Digital Media Technology IDMT Institute in Germany, and designed in collaboration with a rehabilitation clinic in Colombia. HapHop-Physio was tested and evaluated to probe its functionality and user satisfaction. Conclusion: The results show the development of an easy-to-use and funny game by a multidisciplinary team using state-of-the-art videogame technologies and software methodologies. Children testing the game concluded that they would like to play again while undergoing rehabilitation therapies. Keywords: computer game, exer-games, cognitive therapies, rehabilitation
-
DeCiccio, Albert C.
2010-01-01
(Purpose) This is a report about the Urban and Rural Healthcare Academy Pilot Program (HAP) that launched at Southern Vermont College (SVC) and Wheelock College (WC) in summer 2010. HAP enabled 18 vulnerable high school students to learn about how to progress to college, how to transition when they arrive on a college campus, and how to prepare…
-
International Nuclear Information System (INIS)
Guan Donghua; Chen Zhiqing; Huang Chunpeng; Lin Yinghe
2008-01-01
In this study, poly(3-hydroxybutyrate) (PHB)-based scaffolds containing nanosized hydroxyapatite (nHAP) were manufactured by gas-jet/electrospinning. The morphologies of the scaffolds were characterized. The effect of the scaffolds on attachment, proliferation and differentiation of the bone marrow stroma cells (BMSCs) were accessed by using scanning electron microscopy (SEM), methylthiazol tetrazolium (MTT) assay and alkaline phosphatase (ALP) activity. The results show that the gas-jet/electrospun scaffolds possess an extracellular matrix-like topography. In vitro studies describe that the scaffolds have positive effects on attachment, proliferation and differentiation of BMSCs in vitro. It can be concluded that the scaffolds combing the unique structural features generated by gas-jet/electrospinning with functional factors, have the potential to be used in bone tissue engineering
-
An evaluation of the performance of tag SNPs derived from HapMap in a Caucasian population.
Directory of Open Access Journals (Sweden)
Alexandre Montpetit
2006-03-01
Full Text Available The Haplotype Map (HapMap project recently generated genotype data for more than 1 million single-nucleotide polymorphisms (SNPs in four population samples. The main application of the data is in the selection of tag single-nucleotide polymorphisms (tSNPs to use in association studies. The usefulness of this selection process needs to be verified in populations outside those used for the HapMap project. In addition, it is not known how well the data represent the general population, as only 90-120 chromosomes were used for each population and since the genotyped SNPs were selected so as to have high frequencies. In this study, we analyzed more than 1,000 individuals from Estonia. The population of this northern European country has been influenced by many different waves of migrations from Europe and Russia. We genotyped 1,536 randomly selected SNPs from two 500-kbp ENCODE regions on Chromosome 2. We observed that the tSNPs selected from the CEPH (Centre d'Etude du Polymorphisme Humain from Utah (CEU HapMap samples (derived from US residents with northern and western European ancestry captured most of the variation in the Estonia sample. (Between 90% and 95% of the SNPs with a minor allele frequency of more than 5% have an r2 of at least 0.8 with one of the CEU tSNPs. Using the reverse approach, tags selected from the Estonia sample could almost equally well describe the CEU sample. Finally, we observed that the sample size, the allelic frequency, and the SNP density in the dataset used to select the tags each have important effects on the tagging performance. Overall, our study supports the use of HapMap data in other Caucasian populations, but the SNP density and the bias towards high-frequency SNPs have to be taken into account when designing association studies.
-
40 CFR 63.5994 - How do I conduct tests and procedures for tire production affected sources?
2010-07-01
... reductions from add-on control devices. If you want to take credit in Equations 2 and 4 of this section for... add-on control device so that the monthly average HAP emissions do not exceed the HAP constituent... monthly period when complying by using a control device to reduce HAP emissions so that the monthly...
-
Emission factor ratios, SOA mass yields, and the impact of vehicular emissions on SOA formation
Ensberg, J. J.; Hayes, P. L.; Jimenez, J. L.; Gilman, J. B.; Kuster, W. C.; de Gouw, J. A.; Holloway, J. S.; Gordon, T. D.; Jathar, S.; Robinson, A. L.; Seinfeld, J. H.
2014-03-01
The underprediction of ambient secondary organic aerosol (SOA) levels by current atmospheric models in urban areas is well established, yet the cause of this underprediction remains elusive. Likewise, the relative contribution of emissions from gasoline- and diesel-fueled vehicles to the formation of SOA is generally unresolved. We investigate the source of these two discrepancies using data from the 2010 CalNex experiment carried out in the Los Angeles Basin (Ryerson et al., 2013). Specifically, we use gas-phase organic mass (GPOM) and CO emission factors in conjunction with measured enhancements in oxygenated organic aerosol (OOA) relative to CO to quantify the significant lack of closure between expected and observed organic aerosol concentrations attributable to fossil-fuel emissions. Two possible conclusions emerge from the analysis to yield consistency with the ambient data: (1) vehicular emissions are not a dominant source of anthropogenic fossil SOA in the Los Angeles Basin, or (2) the ambient SOA mass yields used to determine the SOA formation potential of vehicular emissions are substantially higher than those derived from laboratory chamber studies.
-
Cayuela, Maria L.; Aguilera, Eduardo; Sanz-Cobena, Alberto; Adams, Dean C.; Abalos, Diego; Barton, Louise; Ryals, Rebecca; Silver, Whendee L.; Alfaro, Marta A.; Pappa, Valentini A.; Smith, Pete; Garnier, Josette; Billen, Gilles; Bouwman, Lex; Bondeau, Alberte; Lassaletta, Luis
2017-01-01
Many recent reviews and meta-analyses of N2O emissions do not include data from Mediterranean studies. In this paper we present a meta-analysis of the N2O emissions from Mediterranean cropping systems, and propose a more robust and reliable regional emission factor (EF) for N2O, distinguishing the
-
Duarte, Márcio; Vicente, Estela; Calvo, Ana; Nunes, Teresa; Tarelho, Luis; Alves, Célia
2014-05-01
In the last years, the importance of biomass fuels has increased mainly for two reasons. One of them is the effort to control the emissions of greenhouse gases, and on the other hand, the increasing costs associated with fossil fuels. Besides that, biomass burning is now recognised as one of the major sources contributing to high concentrations of particulate matter, especially during winter time. Southern European countries have a lack of information regarding emission profiles from biomass burning. Because of that, in most source apportionment studies, the information used comes from northern and alpine countries, whose combustion appliances, fuels and habits are different from those in Mediterranean countries. Due to this lack of information, series of tests using different types of equipment, as well as fuels, were carried out in order to obtain emission profiles and emission factors that correspond to the reality in southern European countries. Tests involved three types of biomass appliances used in Portugal, a fireplace, a woodstove and a modern pellet stove. Emission factors (mg.kg-1 fuel, dry basis) for CO, THC and PM10 were obtained. CO emission factors ranged from 38, for pine on the woodstove, to 84 for eucalyptus in the fireplace. THC emissions were between 4 and 24, for pine in the woodstove and eucalyptus in the fireplace, respectively. PM10 emission factors were in the range from 3.99, for pine in the woodstove, to 17.3 for eucalyptus in the fireplace. On average, the emission factors obtained for the fireplace are 1.5 (CO) to 4 (THC) times higher than those of the woodstove. The fireplace has emission factors for CO, THC and PM10 10, 35 and 32 times, respectively, higher than the pellet stove.
-
Dong, Feihong; Li, Hongjun; Gong, Xiangwu; Liu, Quan; Wang, Jingchao
2015-09-03
A typical application scenario of remote wireless sensor networks (WSNs) is identified as an emergency scenario. One of the greatest design challenges for communications in emergency scenarios is energy-efficient transmission, due to scarce electrical energy in large-scale natural and man-made disasters. Integrated high altitude platform (HAP)/satellite networks are expected to optimally meet emergency communication requirements. In this paper, a novel integrated HAP/satellite (IHS) architecture is proposed, and three segments of the architecture are investigated in detail. The concept of link-state advertisement (LSA) is designed in a slow flat Rician fading channel. The LSA is received and processed by the terminal to estimate the link state information, which can significantly reduce the energy consumption at the terminal end. Furthermore, the transmission power requirements of the HAPs and terminals are derived using the gradient descent and differential equation methods. The energy consumption is modeled at both the source and system level. An innovative and adaptive algorithm is given for the energy-efficient path selection. The simulation results validate the effectiveness of the proposed adaptive algorithm. It is shown that the proposed adaptive algorithm can significantly improve energy efficiency when combined with the LSA and the energy consumption estimation.
-
Dong, Feihong; Li, Hongjun; Gong, Xiangwu; Liu, Quan; Wang, Jingchao
2015-01-01
A typical application scenario of remote wireless sensor networks (WSNs) is identified as an emergency scenario. One of the greatest design challenges for communications in emergency scenarios is energy-efficient transmission, due to scarce electrical energy in large-scale natural and man-made disasters. Integrated high altitude platform (HAP)/satellite networks are expected to optimally meet emergency communication requirements. In this paper, a novel integrated HAP/satellite (IHS) architecture is proposed, and three segments of the architecture are investigated in detail. The concept of link-state advertisement (LSA) is designed in a slow flat Rician fading channel. The LSA is received and processed by the terminal to estimate the link state information, which can significantly reduce the energy consumption at the terminal end. Furthermore, the transmission power requirements of the HAPs and terminals are derived using the gradient descent and differential equation methods. The energy consumption is modeled at both the source and system level. An innovative and adaptive algorithm is given for the energy-efficient path selection. The simulation results validate the effectiveness of the proposed adaptive algorithm. It is shown that the proposed adaptive algorithm can significantly improve energy efficiency when combined with the LSA and the energy consumption estimation. PMID:26404292
-
Directory of Open Access Journals (Sweden)
Feihong Dong
2015-09-01
Full Text Available A typical application scenario of remote wireless sensor networks (WSNs is identified as an emergency scenario. One of the greatest design challenges for communications in emergency scenarios is energy-efficient transmission, due to scarce electrical energy in large-scale natural and man-made disasters. Integrated high altitude platform (HAP/satellite networks are expected to optimally meet emergency communication requirements. In this paper, a novel integrated HAP/satellite (IHS architecture is proposed, and three segments of the architecture are investigated in detail. The concept of link-state advertisement (LSA is designed in a slow flat Rician fading channel. The LSA is received and processed by the terminal to estimate the link state information, which can significantly reduce the energy consumption at the terminal end. Furthermore, the transmission power requirements of the HAPs and terminals are derived using the gradient descent and differential equation methods. The energy consumption is modeled at both the source and system level. An innovative and adaptive algorithm is given for the energy-efficient path selection. The simulation results validate the effectiveness of the proposed adaptive algorithm. It is shown that the proposed adaptive algorithm can significantly improve energy efficiency when combined with the LSA and the energy consumption estimation.
-
Real-world vehicle emission factors in Chinese metropolis city--Beijing.
Wang, Qi-dong; He, Ke-bin; Huo, Hong; Lents, James
2005-01-01
The dynamometer tests with different driving cycles and the real-world tests are presented. Results indicated the pollutants emission factors and fuel consumption factor with ECE15 + EUDC driving cycle usually take the lowest value and with real world driving cycle occur the highest value, and different driving cycles will lead to significantly different vehicle emission factors with the same vehicle. Relative to the ECE15 + EUDC driving cycle, the increasing rate of pollutant emission factors of CO, NOx and HC are - 0.42-2.99, -0.32-0.81 and -0.11-11 with FTP75 testing, 0.11-1.29, -0.77-0.64 and 0.47-10.50 with Beijing 1997 testing and 0.25-1.83, 0.09-0.75 and - 0.58-1.50 with real world testing. Compared to the carburetor vehicles, the retrofit and MPI + TWC vehicles' pollution emissionfactors decrease with different degree. The retrofit vehicle (Santana) will reduce 4.44%-58.44% CO, -4.95%-36.79% NOx, -32.32%-33.89% HC, and -9.39%-14.29% fuel consumption, and especially that the MPI + TWC vehicle will decrease CO by 82.48%-91.76%, NOx by 44.87%-92.79%, HC by 90.00%-93.89% and fuel consumption by 5.44%-10.55%. Vehicles can cause pollution at a very high rate when operated in high power modes; however, they may not often operate in these high power modes. In analyzing vehicle emissions, it describes the fraction of time that vehicles operate in various power modes. In Beijing, vehicles spend 90% of their operation in low power modes or decelerating.
-
Directory of Open Access Journals (Sweden)
F. S. Zhang
2011-10-01
Full Text Available Nitrous oxide (N2O is a long-lived greenhouse gas with a large radiation intensity and it is emitted mainly from agricultural land. Accurate estimates of total direct N2O emissions from croplands on a country scale are important for global budgets of anthropogenic sources of N2O emissions and for the development of effective mitigation strategies. The objectives of this study were to re-estimate direct N2O emissions using localized emission factors and a database of measurements from Chinese croplands. We obtained N2O emission factors for paddy fields (0.41 ± 0.04% and uplands (1.05 ± 0.02% from a normalization process through cube root transformation of the original data. After comparing the results of normalization from the original values, Logarithmic and cube root transformations were used because the frequency of the original data was not normally distributed. Direct N2O emissions from Chinese croplands from 1980 to 2007 were estimated using IPCC (2006 guidelines combined with separate localized emission factors for paddy fields and upland areas. Direct N2O emissions from paddy fields showed little change, increasing by 10.5% with an annual rate of increase of 0.4% from 32.3 Gg N2O-N in 1980 to 35.7 Gg N2O-N in 2007. In contrast, emissions from uplands changed dramatically, increasing by 308% with an annual rate of 11% from 68.0 Gg N2O-N in 1980 to 278 Gg N2O-N in 2007. Total direct N2O emissions from Chinese croplands increased by 213% with an annual rate of 7.6% from 100 Gg N2O-N in 1980 to 313 Gg N2O-N in 2007, and were determined mainly by upland emissions (accounting for 67.8–88.6% of total emissions from 1980 to 2007. Synthetic N fertilizers played a major role in N2O emissions from agricultural land, and the magnitude of the contributions to total direct N2O emissions made by different amendments was synthetic N fertilizer > manure > straw, representing about 78, 15, and 6% of total direct N2O emissions, respectively, between
-
A Study on Vehicle Emission Factor Correction Based on Fuel Consumption Measurement
Wang, Xiaoning; Li, Meng; Peng, Bo
2018-01-01
The objective of this study is to address the problem of obvious differences between the calculated and measured emissions of pollutants from motor vehicle by using the existing "Environmental Impact Assessment Specification of Highway Construction Projects". First, a field study collects the vehicle composition ratio, speed, slope, fuel consumption and other essential data. Considering practical applications, the emission factors corresponding to 40km/h and 110km/h and 120km/h velocity are introduced by data fitting. Then, the emission factors of motor vehicle are revised based on the measured fuel consumption, and the pollutant emission modified formula was calculated and compared with the standard recommendation formula. The results show the error between calculated and measured values are within 5%, which can better reflect the actual discharge of the motor vehicle.
-
2010-07-01
..., and Reconstructed Spark Ignition, 4SRB Stationary RICE >500 HP Located at a Major Source of HAP... Limitations for Existing, New, and Reconstructed Spark Ignition, 4SRB Stationary RICE >500 HP Located at a... emission limitations for existing, new and reconstructed 4SRB stationary RICE at 100 percent load plus or...
-
2010-07-01
... 40 Protection of Environment 11 2010-07-01 2010-07-01 true HAP ABA Formulation Limitations Matrix for New Sources [see § 63.1297(d)(2)] 1 Table 1 to Subpart III of Part 63 Protection of Environment... Flexible Polyurethane Foam Production Pt. 63, Subpt. III, Table 1 Table 1 to Subpart III of Part 63—HAP ABA...
-
Greenhouse gas emission factor development for coal-fired power plants in Korea
International Nuclear Information System (INIS)
Jeon, Eui-Chan; Myeong, Soojeong; Sa, Jae-Whan; Kim, Jinsu; Jeong, Jae-Hak
2010-01-01
Accurate estimation of greenhouse gas emissions is essential for developing an appropriate strategy to mitigate global warming. This study examined the characteristics of greenhouse gas emission from power plants, a major greenhouse gas source in Korea. The power plants examined use bituminous coal, anthracite, and sub-bituminous coal as fuel. The CO 2 concentration from power plants was measured using GC-FID with methanizer. The amount of carbon, hydrogen, and calorific values in the input fuel was measured using an elemental analyzer and calorimeter. For fuel analysis, CO 2 emission factors for anthracite, bituminous coal, and sub-bituminous coal were 108.9, 88.4, and 97.9 Mg/kJ, respectively. The emission factors developed in this study were compared with those for IPCC. The results showed that CO 2 emission was 10.8% higher for anthracite, 5.5% lower for bituminous coal, and 1.9% higher for sub-bituminous coal than the IPCC figures.
-
An analysis of candidates for addition to the Clean Air Act list of hazardous air pollutants
Energy Technology Data Exchange (ETDEWEB)
Sonya Lunder; Tracey J. Woodruff; Daniel A. Axelrad [University of California, Berkeley, CA (United States). School of Public Health
2004-02-01
There are 188 air toxics listed as hazardous air pollutants (HAPs) in the Clean Air Act (CAA), based on their potential to adversely impact public health. This paper presents several analyses performed to screen potential candidates for addition to the HAPs list. We analyzed 1086 HAPs and potential HAPs, including chemicals regulated by the state of California or with emissions reported to the Toxics Release Inventory (TRI). HAPs and potential HAPs were ranked by their emissions to air, and by toxicity-weighted (tox-wtd) emissions for cancer and noncancer, using emissions information from the TRI and toxicity information from state and federal agencies. Separate consideration was given for persistent, bioaccumulative toxins (PBTs), reproductive or developmental toxins, and chemicals under evaluation for regulation as toxic air contaminants in California. Forty-four pollutants were identified as candidate HAPs based on three ranking analyses and whether they were a PBT or a reproductive or developmental toxin. Of these, nine qualified in two or three different rankings (ammonia (NH{sub 3}), copper (Cu), Cu compounds, nitric acid (HNO{sub 3}), N-methyl-2-pyrrolidone, sulfuric acid (H{sub 2}SO{sub 4}), vanadium (V) compounds, zinc (Zn), and Zn compounds). This analysis suggests further evaluation of several pollutants for possible addition to the CAA list of HAPs. 28 refs., 2 figs., 11 tabs.
-
Building Entry Loss and Delay Spread Measurements on a Simulated HAP-to-Indoor Link at S-Band
Directory of Open Access Journals (Sweden)
Delgado-Penín JA
2008-01-01
Full Text Available Results from a measurement campaign emulating the high altitude platform (HAP-to-indoor communication channel at S-band are presented in this paper. A link was established between a transmitter carried by a helicopter, representing the HAP, and a receiver placed at several locations in different building types including an airport, an office building, a shopping mall, a residential house, and a skyscraper. A wideband, directive channel sounder was used to measure building entry loss and time delay spread. Results of the building entry loss are presented as a function of building type, elevation, and building entry angle. Results of delay spread for each building are also provided.
-
Building Entry Loss and Delay Spread Measurements on a Simulated HAP-to-Indoor Link at S-Band
Directory of Open Access Journals (Sweden)
P. Valtr
2008-07-01
Full Text Available Results from a measurement campaign emulating the high altitude platform (HAP-to-indoor communication channel at S-band are presented in this paper. A link was established between a transmitter carried by a helicopter, representing the HAP, and a receiver placed at several locations in different building types including an airport, an office building, a shopping mall, a residential house, and a skyscraper. A wideband, directive channel sounder was used to measure building entry loss and time delay spread. Results of the building entry loss are presented as a function of building type, elevation, and building entry angle. Results of delay spread for each building are also provided.
-
Transport sector CO2 emissions growth in Asia: Underlying factors and policy options
International Nuclear Information System (INIS)
Timilsina, Govinda R.; Shrestha, Ashish
2009-01-01
This study analyze the potential factors influencing the growth of transport sector carbon dioxide (CO 2 ) emissions in selected Asian countries during the 1980-2005 period by decomposing annual emissions growth into components representing changes in fuel mix, modal shift, per capita gross domestic product (GDP) and population, as well as changes in emission coefficients and transportation energy intensity. We find that changes in per capita GDP, population growth and transportation energy intensity are the main factors driving transport sector CO 2 emission growth in the countries considered. While growth in per capita income and population are responsible for the increasing trend of transport sector CO 2 emissions in China, India, Indonesia, Republic of Korea, Malaysia, Pakistan, Sri Lanka and Thailand; the decline of transportation energy intensity is driving CO 2 emissions down in Mongolia. Per capita GDP, population and transportation energy intensity effects are all found responsible for transport sector CO 2 emissions growth in Bangladesh, the Philippines and Vietnam. The study also reviews existing government policies to limit CO 2 emissions growth, such as fiscal instruments, fuel economy standards and policies to encourage switching to less emission intensive fuels and transportation modes.
-
Trace emissions from gaseous combustion
Energy Technology Data Exchange (ETDEWEB)
Seebold, J.G. [Chevron Research and Technology Co., Richmond, CA (United States)
2000-07-01
The U.S. Clean Air Act (CAA) was amended in 1990 to include the development of maximum achievable control technology (MACT) emission standards for hazardous air pollutants (HAPs) for certain stationary sources by November 2000. MACT emissions standards would affect process heaters and industrial boilers since combustion processes are a potential source for many air toxins. The author noted that one of the problems with MACT is the lack of a clear solid scientific footing which is needed to develop environmentally responsible regulations. In order to amend some of these deficiencies, a 4-year, $7 million research project on the origin and fate of trace emissions in the external combustion of gaseous hydrocarbons was undertaken in a collaborative effort between government, universities and industry. This collaborative project entitled the Petroleum Environmental Research Forum (PERF) Project 92-19 produced basic information and phenomenological understanding in two important areas, one basic and one applied. The specific objectives of the project were to measure emissions while operating different full-scale burners under various operating conditions and then to analyze the emission data to identify which operating conditions lead to low air toxic emissions. Another objective was to develop new chemical kinetic mechanisms and predictive models for the formation of air toxic species which would explain the origin and fate of these species in process heaters and industrial boilers. It was determined that a flame is a very effective reactor and that trace emissions from a typical gas-fired industry burner are very small. An unexpected finding was that trace emissions are not affected by hydrocarbon gaseous fuel composition, nor by the use of ultra low nitrous oxide burners. 2 refs., 8 figs.
-
Gibe, Hezron P.; Cayetano, Mylene G.
2017-09-01
Exposure to particulate matter (PM) is a serious environmental problem in many urban areas on Earth. In the Philippines, most existing studies and emission inventories have mainly focused on point and mobile sources, while research involving human exposures to particulate pollutants is rare. This paper presents a method for estimating the amount of fine particulate (PM2.5) emissions in a test study site in the city of Cabanatuan, Nueva Ecija, in the Philippines, by utilizing local emission factors, regionally procured data, and land cover/land use (activity data) interpreted from satellite imagery. Geographic information system (GIS) software was used to map the estimated emissions in the study area. The present results suggest that vehicular emissions from motorcycles and tricycles, as well as fuels used by households (charcoal) and burning of agricultural waste, largely contribute to PM2.5 emissions in Cabanatuan. Overall, the method used in this study can be applied in other small urbanizing cities, as long as on-site specific activity, emission factor, and satellite-imaged land cover data are available.
-
Energy Technology Data Exchange (ETDEWEB)
Nielsen, Joergen Bremnes; Stenersen, Dag
2010-11-15
In this report new and updated emission factors for diesel, HFO and gas fuelled ships are presented and discussed as follows; NO{sub x} reduction factors from ships with NO{sub x} reduction measures; NO{sub x} emission factor from gas operated vessels; Methane emission factors for gas operated vessels; Updated emission factors for particulate emissions (PM) with a specific factor for the black carbon (BC) fraction of particulate emissions; A discussion on how low sulfur fuel will affect emissions of PM emissions and the BC fraction of PM is also included. (Author)
-
Research on impacts of population-related factors on carbon emissions in Beijing from 1984 to 2012
International Nuclear Information System (INIS)
Yang, Yayun; Zhao, Tao; Wang, Yanan; Shi, Zhaohui
2015-01-01
Carbon emissions related to population factors have aroused great attention around the world. A multitude of literature mainly focused on single demographic impacts on environmental issues at the national level, and comprehensive studies concerning population-related factors at a city level are rare. This paper employed STIRPAT (Stochastic Impacts by Regression on Population, Affluence and Technology) model incorporating PLS (Partial least squares) regression method to examine the influence of population-related factors on carbon emissions in Beijing from 1984 to 2012. Empirically results manifest that urbanization is the paramount driver. Changes in population age structure have significantly positive impacts on carbon emissions, and shrinking young population, continuous expansion of working age population and aging population will keep on increasing environmental pressures. Meanwhile, shrinking household size and expanding floating population boost the discharge of carbon emissions. Besides, per capita consumption is an important contributor of carbon emissions, while industry energy intensity is the main inhibitory factor. Based upon these findings and the specific circumstances of Beijing, policies such as promoting clean and renewable energy, improving population quality and advocating low carbon lifestyles should be enhanced to achieve targeted emissions reductions. - Highlights: • We employed the STIRPAT model to identify population-related factors of carbon emissions in Beijing. • Urbanization is the paramount driver of carbon emissions. • Changes in population age structure exert significantly positive impacts on carbon emissions. • Shrinking household size, expanding floating population and improving consumption level increase carbon emissions. • Industry energy intensity decreases carbon emissions
-
Research on impacts of population-related factors on carbon emissions in Beijing from 1984 to 2012
Energy Technology Data Exchange (ETDEWEB)
Yang, Yayun; Zhao, Tao; Wang, Yanan, E-mail: wyn3615@126.com; Shi, Zhaohui
2015-11-15
Carbon emissions related to population factors have aroused great attention around the world. A multitude of literature mainly focused on single demographic impacts on environmental issues at the national level, and comprehensive studies concerning population-related factors at a city level are rare. This paper employed STIRPAT (Stochastic Impacts by Regression on Population, Affluence and Technology) model incorporating PLS (Partial least squares) regression method to examine the influence of population-related factors on carbon emissions in Beijing from 1984 to 2012. Empirically results manifest that urbanization is the paramount driver. Changes in population age structure have significantly positive impacts on carbon emissions, and shrinking young population, continuous expansion of working age population and aging population will keep on increasing environmental pressures. Meanwhile, shrinking household size and expanding floating population boost the discharge of carbon emissions. Besides, per capita consumption is an important contributor of carbon emissions, while industry energy intensity is the main inhibitory factor. Based upon these findings and the specific circumstances of Beijing, policies such as promoting clean and renewable energy, improving population quality and advocating low carbon lifestyles should be enhanced to achieve targeted emissions reductions. - Highlights: • We employed the STIRPAT model to identify population-related factors of carbon emissions in Beijing. • Urbanization is the paramount driver of carbon emissions. • Changes in population age structure exert significantly positive impacts on carbon emissions. • Shrinking household size, expanding floating population and improving consumption level increase carbon emissions. • Industry energy intensity decreases carbon emissions.
-
DEFF Research Database (Denmark)
Larsen, Anna Warberg; Astrup, Thomas
2011-01-01
variations between emission factors for different incinerators, but the background for these variations has not been thoroughly examined. One important reason may be variations in collection of recyclable materials as source separation alters the composition of the residual waste incinerated. The objective...... routed to incineration. Emission factors ranged from 27 to 40kg CO2/GJ. The results appeared most sensitive towards variations in waste composition and water content. Recycling rates and lower heating values could not be used as simple indicators of the resulting emission factors for residual household...... different studies and when using the values for environmental assessment purposes....
-
78 FR 64496 - Acid Rain Program: Notice of Annual Adjustment Factors for Excess Emissions Penalty
2013-10-29
... Factors for Excess Emissions Penalty AGENCY: Environmental Protection Agency (EPA). ACTION: Notice of annual adjustment factors for excess emissions penalty. SUMMARY: The Acid Rain Program under title IV of... excess tons emitted times $2,000 as adjusted by an annual adjustment factor, which must be published in...
-
Livestock play an important role in carbon cycling through consumption of biomass and emissions of methane. Recent research suggests that existing bottom-up inventories of livestock methane emissions in the U.S., such as those made using 2006 IPCC Tier 1 livestock emissions factors, are too low. Thi...
-
Emission factor of ammonia (NH3) from on-road vehicles in China: tunnel tests in urban Guangzhou
Liu, Tengyu; Wang, Xinming; Wang, Boguang; Ding, Xiang; Deng, Wei; Lü, Sujun; Zhang, Yanli
2014-05-01
Ammonia (NH3) is the primary alkaline gas in the atmosphere that contributes to formation of secondary particles. Emission of NH3 from vehicles, particularly gasoline powered light duty vehicles equipped with three-way catalysts, is regarded as an important source apart from emissions from animal wastes and soils, yet measured emission factors for motor vehicles are still not available in China, where traffic-related emission has become an increasingly important source of air pollutants in urban areas. Here we present our tunnel tests for NH3 from motor vehicles under ‘real world conditions’ in an urban roadway tunnel in Guangzhou, a central city in the Pearl River Delta (PRD) region in south China. By attributing all NH3 emissions in the tunnel to light-duty gasoline vehicles, we obtained a fuel-based emission rate of 2.92 ± 0.18 g L-1 and a mileage-based emission factor of 229.5 ± 14.1 mg km-1. These emission factors were much higher than those measured in the United States while measured NO x emission factors (7.17 ± 0.60 g L-1 or 0.56 ± 0.05 g km-1) were contrastingly near or lower than those previously estimated by MOBILE/PART5 or COPERT IV models. Based on the NH3 emission factors from this study, on-road vehicles accounted for 8.1% of NH3 emissions in the PRD region in 2006 instead of 2.5% as estimated in a previous study using emission factors taken from the Emission Inventory Improvement Program (EIIP) in the United States.
-
Emission factor of ammonia (NH3) from on-road vehicles in China: tunnel tests in urban Guangzhou
International Nuclear Information System (INIS)
Liu, Tengyu; Wang, Xinming; Ding, Xiang; Deng, Wei; Lü, Sujun; Zhang, Yanli; Wang, Boguang
2014-01-01
Ammonia (NH 3 ) is the primary alkaline gas in the atmosphere that contributes to formation of secondary particles. Emission of NH 3 from vehicles, particularly gasoline powered light duty vehicles equipped with three-way catalysts, is regarded as an important source apart from emissions from animal wastes and soils, yet measured emission factors for motor vehicles are still not available in China, where traffic-related emission has become an increasingly important source of air pollutants in urban areas. Here we present our tunnel tests for NH 3 from motor vehicles under ‘real world conditions’ in an urban roadway tunnel in Guangzhou, a central city in the Pearl River Delta (PRD) region in south China. By attributing all NH 3 emissions in the tunnel to light-duty gasoline vehicles, we obtained a fuel-based emission rate of 2.92 ± 0.18 g L −1 and a mileage-based emission factor of 229.5 ± 14.1 mg km −1 . These emission factors were much higher than those measured in the United States while measured NO x emission factors (7.17 ± 0.60 g L −1 or 0.56 ± 0.05 g km −1 ) were contrastingly near or lower than those previously estimated by MOBILE/PART5 or COPERT IV models. Based on the NH 3 emission factors from this study, on-road vehicles accounted for 8.1% of NH 3 emissions in the PRD region in 2006 instead of 2.5% as estimated in a previous study using emission factors taken from the Emission Inventory Improvement Program (EIIP) in the United States. (letter)
-
Nitrous oxide emission factors from N-fertilizer in sugarcane production in Brazil
Galdos, M. V.; Siqueira Neto, M.; Feigl, B. J.; Carvalho, J. L.; Cerri, C. E.; Cerri, C. C.
2013-12-01
The Brazilian sugarcane production is rapidly expanding due to the increase of global demand for ethanol. Concurrently the necessary inputs to culture, especially N-fertilizer, are growing, since N is one of the key element to maintain sugarcane productivity. However, it is known that N-fertilizer is responsible for the largest share of N2O emissions from agricultural soils. The Intergovernmental Panel on Climate Changes (IPCC) estimated that under favorable climatic conditions approximately 1% of the N-fertilizer applied can be emitted as N2O. Our goal was to estimate N2O emission factors from N-fertilizer used in the sugarcane ratoon for ethanol production. A field study was conducted at the Capuava Mill, located in southeastern Brazil. The experimental design was completely randomized, with four replications in a factorial scheme (2 x 2): two N sources (urea and ammonium nitrate), two application rates (80 and 120 kg ha-1), and a control treatment. N2O concentrations were determined by gas chromatography using a Shimadzu© GC-mini. N2O fluxes were calculated from linear regressions of concentration versus incubation time in the soil static chambers. The N2O emission factor of N-fertilizer was calculated according to the methodology described in the Guidelines for National Greenhouse Gas Inventories (IPCC). Comparatively, ammonium nitrate emitted 45 to 75% less N2O than urea application. There was no significant difference in N2O emission between the two applied rates of urea. Also the N2O emission factor of ammonium nitrate (0.3×0.2%) was lower than that of urea (1.1×0.4%). Our results indicated that on average the N fertilization of sugarcane plantation has an emission factor of 0.7×0.5% suggesting that N-fertilizer management can be used to reduce greenhouse gas emissions in order to improve the sustainability of bioethanol from sugarcane.
-
Real-time emission factor measurements of isocyanic acid from light duty gasoline vehicles.
Brady, James M; Crisp, Timia A; Collier, Sonya; Kuwayama, Toshihiro; Forestieri, Sara D; Perraud, Véronique; Zhang, Qi; Kleeman, Michael J; Cappa, Christopher D; Bertram, Timothy H
2014-10-07
Exposure to gas-phase isocyanic acid (HNCO) has been previously shown to be associated with the development of atherosclerosis, cataracts and rheumatoid arthritis. As such, accurate emission inventories for HNCO are critical for modeling the spatial and temporal distribution of HNCO on a regional and global scale. To date, HNCO emission rates from light duty gasoline vehicles, operated under driving conditions, have not been determined. Here, we present the first measurements of real-time emission factors of isocyanic acid from a fleet of eight light duty gasoline-powered vehicles (LDGVs) tested on a chassis dynamometer using the Unified Driving Cycle (UC) at the California Air Resources Board (CARB) Haagen-Smit test facility, all of which were equipped with three-way catalytic converters. HNCO emissions were observed from all vehicles, in contrast to the idealized laboratory measurements. We report the tested fleet averaged HNCO emission factors, which depend strongly on the phase of the drive cycle; ranging from 0.46 ± 0.13 mg kg fuel(-1) during engine start to 1.70 ± 1.77 mg kg fuel(-1) during hard acceleration after the engine and catalytic converter were warm. The tested eight-car fleet average fuel based HNCO emission factor was 0.91 ± 0.58 mg kg fuel(-1), within the range previously estimated for light duty diesel-powered vehicles (0.21-3.96 mg kg fuel(-1)). Our results suggest that HNCO emissions from LDGVs represent a significant emission source in urban areas that should be accounted for in global and regional models.
-
VOC and HAP recovery using ionic liquids
Energy Technology Data Exchange (ETDEWEB)
Michael R. Milota : Kaichang Li
2007-05-29
During the manufacture of wood composites, paper, and to a lesser extent, lumber, large amounts of volatile organic compounds (VOCs) such as terpenes, formaldehyde, and methanol are emitted to air. Some of these compounds are hazardous air pollutants (HAPs). The air pollutants produced in the forest products industry are difficult to manage because the concentrations are very low. Presently, regenerative thermal oxidizers (RTOs and RCOs) are commonly used for the destruction of VOCs and HAPs. RTOs consume large amounts of natural gas to heat air and moisture. The combustion of natural gas generates increased CO2 and NOx, which have negative implications for global warming and air quality. The aforementioned problems are addressed by an absorption system containing a room-temperature ionic liquid (RTIL) as an absorbent. RTILs are salts, but are in liquid states at room temperature. RTILs, an emerging technology, are receiving much attention as replacements for organic solvents in industrial processes with significant cost and environmental benefits. Some of these processes include organic synthesis, extraction, and metal deposition. RTILs would be excellent absorbents for exhausts from wood products facilities because of their unique properties: no measurable vapor pressure, high solubility of wide range of organic compounds, thermal stability to 200°C (almost 400°F), and immisciblity with water. Room temperature ionic liquids were tested as possible absorbents. Four were imidizolium-based and were eight phosphonium-based. The imidizolium-based ionic liquids proved to be unstable at the conditions tested and in the presence of water. The phosphonium-based ionic liquids were stable. Most were good absorbents; however, cleaning the contaminates from the ionic liquids was problematic. This was overcome with a higher temperature (120°C) than originally proposed and a very low pressure (1 kPa. Absorption trials were conducted with tetradecy
-
40 CFR 63.5749 - How do I calculate the organic HAP content of aluminum wipedown solvents?
2010-07-01
... Manufacturing Standards for Aluminum Recreational Boat Surface Coating Operations § 63.5749 How do I calculate... fraction of organic HAP in aluminum wipedown solvent j. m = number of different aluminum surface coatings...
-
Directory of Open Access Journals (Sweden)
Fiona Angrisano
2017-12-01
Full Text Available Summary: Inhibiting transmission of Plasmodium is a central strategy in malarial eradication, and the biological process of gamete fusion during fertilization is a proven target for this approach. The lack of a structure or known molecular function of current anti-malarial vaccine targets has previously been a hindrance in the development of transmission-blocking vaccines. Structure/function studies have indicated that the conserved gamete membrane fusion protein HAP2 is a class II viral fusion protein. Here, we demonstrate that targeting a function-critical site of the fusion/cd loop with species-specific antibodies reduces Plasmodium berghei transmission in vivo by 58.9% and in vitro fertilization by up to 89.9%. A corresponding reduction in P. falciparum transmission (75.5%/36.4% reductions in intensity/prevalence is observed in complimentary field studies. These results emphasize conserved mechanisms of fusion in Apicomplexa, while highlighting an approach to design future anti-malarial transmission-blocking vaccines. : Angrisano et al. find that the HAP2 cd-loop can be targeted as an anti-malarial intervention, is immunogenic across multiple plasmodial species, can induce antibodies that specifically recognize the sexual stages of the parasitic life cycle, and can mediate transmission-blocking immunity in the lab and the field. Keywords: HAP2, malaria, transmission, fusion, vaccine
-
Bonding techniques for hybrid active pixel sensors (HAPS)
Energy Technology Data Exchange (ETDEWEB)
Bigas, M. [Centre Nacional de Microelectronica, CNM-IMB (CSIC), Campus Universitat Autonoma de Barcelona, 08193 Bellaterra, Barcelona (Spain)]. E-mail: Marc.Bigas@cnm.es; Cabruja, E. [Centre Nacional de Microelectronica, CNM-IMB (CSIC), Campus Universitat Autonoma de Barcelona, 08193 Bellaterra, Barcelona (Spain)]. E-mail: Enric.Cabruja@cnm.es; Lozano, M. [Centre Nacional de Microelectronica, CNM-IMB (CSIC), Campus Universitat Autonoma de Barcelona, 08193 Bellaterra, Barcelona (Spain)
2007-05-01
A hybrid active pixel sensor (HAPS) consists of an array of sensing elements which is connected to an electronic read-out unit. The most used way to connect these two different devices is bump bonding. This interconnection technique is very suitable for these systems because it allows a very fine pitch and a high number of I/Os. However, there are other interconnection techniques available such as direct bonding. This paper, as a continuation of a review [M. Lozano, E. Cabruja, A. Collado, J. Santander, M. Ullan, Nucl. Instr. and Meth. A 473 (1-2) (2001) 95-101] published in 2001, presents an update of the different advanced bonding techniques available for manufacturing a hybrid active pixel detector.
-
Directory of Open Access Journals (Sweden)
Decai Tang
2016-10-01
Full Text Available According to the economic and energy consumption statistics in Jiangsu Province, we combined the GM (1, 1 grey model and polynomial regression to forecast carbon emissions. Historical and projected emissions were decomposed using the Logarithmic Mean Divisia Index (LMDI approach to assess the relative contribution of different factors to emission variability. The results showed that carbon emissions will continue to increase in Jiangsu province during 2015–2020 period and cumulative carbon emissions will increase by 39.5487 million tons within the forecast period. The growth of gross domestic product (GDP per capita plays the greatest positive role in driving carbon emission growth. Furthermore, the improvement of energy usage efficiency is the primary factor responsible for reducing carbon emissions. Factors of population, industry structure adjustment and the optimization of fuel mix also help to reduce carbon emissions. Based on the LMDI analysis, we provide some advice for policy-makers in Jiangsu and other provinces in China.
-
Air toxics provisions of the Clean Air Act: Potential impacts on energy
International Nuclear Information System (INIS)
Hootman, H.A.; Vernet, J.E.
1991-11-01
This report provides an overview of the provisions of the Clean Air Act and its Amendments of 1990 that identify hazardous air pollutant (HAP) emissions and addresses their regulation by the US Environmental Protection Agency (EPA). It defines the major energy sector sources of these HAPs that would be affected by the regulations. Attention is focused on regulations that would cover coke oven emissions; chromium emission from industrial cooling towers and the electroplating process; HAP emissions from tank vessels, asbestos-related activities, organic solvent use, and ethylene oxide sterilization; and emissions of air toxics from municipal waste combustors. The possible implications of Title III regulations for the coal, natural gas, petroleum, uranium, and electric utility industries are examined. The report discusses five major databases of HAP emissions: (1) TRI (EPA's Toxic Release Inventory); (2) PISCES (Power Plant Integrated Systems: Chemical Emissions Studies developed by the Electric Power Research Institute); (3) 1985 Emissions Inventory on volatile organic compounds (used for the National Acid Precipitation Assessment Program); (4) Particulate Matter Species Manual (EPA); and (5) Toxics Emission Inventory (National Aeronautics and Space Administration). It also offers information on emission control technologies for municipal waste combustors
-
Development of cotton gin PM10 emission factors for EPA’s AP-42-DUPLICATE DO NOT USE
The Compilation of Air Pollution Emission Factors (AP-42) emission factors are assigned ratings, from A (Excellent) to E (Poor), based on the quality of data used to develop them. All current PM10 cotton gin emission factors received quality ratings of D or lower. In an effort to improve these ratin...
-
Jang, Jae-Myung; Kim, Seung-Dai; Park, Tae-Eon; Choe, Han-Cheol
2018-02-01
The biocompatibility structure of an implant surface is of great importance to the formation of new bone tissue around the dental implant and also has a significant chemical reaction in the osseointegration process. Thus, ultra-fine Pd-Ag-HAp nanoparticles have been electrodeposited on protruded TiO2 barrier layer in mixed electrolyte solutions. Unusual protrusions patterns, which are assigned to Pd-Ag-HAp nanoparticles, can be clearly differentiated from a TiO2 nanotube oxide layer formed by an anodizing process. In the chemical bonding state, the surface characteristics of Pd/Ag/HAp compounds have been investigated by FE-SEM, EDS mapping analysis, and XPS analysis. The mapping dots of the elements including Ti, Ca, Pd, Ag, and P showed a homogeneous distribution throughout the entire surface when deposited onto the protruded TiO2 barrier layer. The XPS spectra of Ti-2p, O-1S, Pd-3d, and Ag-3d have been investigated, with the major XPS peak indicating Pd-3d. The Ag-3d level was clearly observed with further scanning of the Ca-2p region. Based on the results of the chemical states, the structural properties of the protrusion patterns were also examined after being deposited onto the barrier oxide film, resulting in the representative protrusion patterns being mainly composed of Pd-Ag-HAp compounds. The results of the soaking evaluation showed that the protrusion patterns and the protruded TiO2 barrier layer were all effective in regards to biocompatibility.
-
The emission factor of volatile isoprenoids: stress, acclimation, and developmental responses
Directory of Open Access Journals (Sweden)
Ü. Niinemets
2010-07-01
Full Text Available The rate of constitutive isoprenoid emissions from plants is driven by plant emission capacity under specified environmental conditions (ES, the emission factor and by responsiveness of the emissions to instantaneous variations in environment. In models of isoprenoid emission, ES has been often considered as intrinsic species-specific constant invariable in time and space. Here we analyze the variations in species-specific values of ES under field conditions focusing on abiotic stresses, past environmental conditions and developmental processes. The reviewed studies highlight strong stress-driven, adaptive (previous temperature and light environment and growth CO2 concentration and developmental (leaf age variations in ES values operating at medium to long time scales. These biological factors can alter species-specific ES values by more than an order of magnitude. While the majority of models based on early concepts still ignore these important sources of variation, recent models are including some of the medium- to long-term controls. However, conceptually different strategies are being used for incorporation of these longer-term controls with important practical implications for parameterization and application of these models. This analysis emphasizes the need to include more biological realism in the isoprenoid emission models and also highlights the gaps in knowledge that require further experimental work to reduce the model uncertainties associated with biological sources of variation.
-
Accuracy of exhaust emission factor measurements on chassis dynamometer
Joumard, R.; Laurikko, J.; Han, T.L.; Geivanidis, S.; Samaras, Z.; Merétei, T.; Devaux, P.; André, J.-M.; Cornelis, E.; Lacour, S.; Prati, M.V.; Vermeulen, R.; Zallinger, M.
2009-01-01
The influence of 20 parameters on the measurement of light-vehicle emission factors on chassis dynamometer based on driving patterns, vehicle-related parameters, vehicle sampling, and laboratory-related parameters, was studied. The results were based on literature synthesis, ≈ 2700 specific tests
-
Emission factors for gaseous and particulate pollutants from offshore diesel engine vessels in China
Zhang, Fan; Chen, Yingjun; Tian, Chongguo; Lou, Diming; Li, Jun; Zhang, Gan; Matthias, Volker
2016-05-01
Shipping emissions have significant influence on atmospheric environment as well as human health, especially in coastal areas and the harbour districts. However, the contribution of shipping emissions on the environment in China still need to be clarified especially based on measurement data, with the large number ownership of vessels and the rapid developments of ports, international trade and shipbuilding industry. Pollutants in the gaseous phase (carbon monoxide, sulfur dioxide, nitrogen oxides, total volatile organic compounds) and particle phase (particulate matter, organic carbon, elemental carbon, sulfates, nitrate, ammonia, metals) in the exhaust from three different diesel-engine-powered offshore vessels in China (350, 600 and 1600 kW) were measured in this study. Concentrations, fuel-based and power-based emission factors for various operating modes as well as the impact of engine speed on emissions were determined. Observed concentrations and emission factors for carbon monoxide, nitrogen oxides, total volatile organic compounds, and particulate matter were higher for the low-engine-power vessel (HH) than for the two higher-engine-power vessels (XYH and DFH); for instance, HH had NOx EF (emission factor) of 25.8 g kWh-1 compared to 7.14 and 6.97 g kWh-1 of DFH, and XYH, and PM EF of 2.09 g kWh-1 compared to 0.14 and 0.04 g kWh-1 of DFH, and XYH. Average emission factors for all pollutants except sulfur dioxide in the low-engine-power engineering vessel (HH) were significantly higher than that of the previous studies (such as 30.2 g kg-1 fuel of CO EF compared to 2.17 to 19.5 g kg-1 fuel in previous studies, 115 g kg-1 fuel of NOx EF compared to 22.3 to 87 g kg-1 fuel in previous studies and 9.40 g kg-1 fuel of PM EF compared to 1.2 to 7.6 g kg-1 fuel in previous studies), while for the two higher-engine-power vessels (DFH and XYH), most of the average emission factors for pollutants were comparable to the results of the previous studies, engine type was
-
Itahashi, S.; Yan, X.; Song, G.; Yan, J.; Xue, Y.
2017-12-01
Gas-fired boilers will become the main stationary sources of NOx in Beijing. However, the knowledge of gas-fired boilers in Beijing is limited. In the present study, the emission characteristics of NOx, SO2, and CO from gas-fired boilers in Beijing were established using category-specific emission factors (EFs) from field measurements. In order to obtain category-specific EFs, boilers were classified through influence analysis. Factors such as combustion mode, boiler type, and installed capacity were considered critical for establishing EFs because they play significant roles in pollutant formation. The EFs for NOx, CO, and SO2 ranged from 1.42-6.86 g m-3, 0.05-0.67 g m-3 and 0.03-0.48 g m-3. The emissions of NOx, SO2, and CO for gas-fired boilers in Beijing were 11121 t, 468 t, and 222 t in 2014, respectively. The emissions were spatially allocated into grid cells with a resolution of 1 km × 1 km, and the results indicated that top emitters were in central Beijing. The uncertainties were quantified using a Monte Carlo simulation. The results indicated high uncertainties in CO (-157% to 154%) and SO2 (-127% to 182%) emissions, and relatively low uncertainties (-34% to 34%) in NOx emission. Furthermore, approximately 61.2% and 96.8% of the monitored chamber combustion boilers (CCBs) met the standard limits for NOx and SO2, respectively. Concerning NOx, low-NOx burners and NOx emission control measures are urgently needed for implementing of stricter standards. Adopting terminal control measures is unnecessary for SO2, although its concentration occasionally exceeds standard limits, because reduction of its concentration can be achieved thorough control of the sulfur content of natural gas at a stable low level. Furthermore, the atmospheric combustion boilers (ACBs) should be substituted with CCBs, because ACBs have a higher emission despite lower gross installed capacity. The results of this study will enable in understanding and controlling emissions from gas
-
Improving and disaggregating N_2O emission factors for ruminant excreta on temperate pasture soils
International Nuclear Information System (INIS)
Krol, D.J.; Carolan, R.; Minet, E.; McGeough, K.L.; Watson, C.J.; Forrestal, P.J.; Lanigan, G.J.; Richards, K.G.
2016-01-01
Cattle excreta deposited on grazed grasslands are a major source of the greenhouse gas (GHG) nitrous oxide (N_2O). Currently, many countries use the IPCC default emission factor (EF) of 2% to estimate excreta-derived N_2O emissions. However, emissions can vary greatly depending on the type of excreta (dung or urine), soil type and timing of application. Therefore three experiments were conducted to quantify excreta-derived N_2O emissions and their associated EFs, and to assess the effect of soil type, season of application and type of excreta on the magnitude of losses. Cattle dung, urine and artificial urine treatments were applied in spring, summer and autumn to three temperate grassland sites with varying soil and weather conditions. Nitrous oxide emissions were measured from the three experiments over 12 months to generate annual N_2O emission factors. The EFs from urine treated soil was greater (0.30–4.81% for real urine and 0.13–3.82% for synthetic urine) when compared with dung (− 0.02–1.48%) treatments. Nitrous oxide emissions were driven by environmental conditions and could be predicted by rainfall and temperature before, and soil moisture deficit after application; highlighting the potential for a decision support tool to reduce N_2O emissions by modifying grazing management based on these parameters. Emission factors varied seasonally with the highest EFs in autumn and were also dependent on soil type, with the lowest EFs observed from well-drained and the highest from imperfectly drained soil. The EFs averaged 0.31 and 1.18% for cattle dung and urine, respectively, both of which were considerably lower than the IPCC default value of 2%. These results support both lowering and disaggregating EFs by excreta type. - Highlights: • N_2O emissions were measured from cattle excreta applied to pasture. • N_2O was universally higher from urine compared with dung. • N_2O was driven by rainfall, temperature and soil moisture deficit. • Emission
-
Emission factors of greenhouse gases from layer and broiler barns in Cameroon
Ngwabie, N. Martin; Acobta, Ada N.; Manga, Veronica E.; VanderZaag, Andrew C.
2018-03-01
Limited information is available in the literature on greenhouse gas (GHG) quantification from livestock production systems in Africa. Therefore, this project was carried out to generate baseline emission factors of methane (CH4), nitrous oxide (N2O) and carbon dioxide (CO2) from broiler and layer barns with building design typical of Cameroon. Emissions were measured from two broiler barns during the entire production cycles and a layer barn for a limited period using flux chambers. Methane emission factors from the broiler barns with mud and cement floors were 0.96 ± 1.04 and 0.36 ± 0.17 mg bird-1 hr-1 respectively, and 0.76 ± 0.56 mg bird-1 hr-1 from the layer barn with cement floor. Nitrous oxide emission from the broiler barns with mud and cement floors were 12.94 ± 10.11 and 1.68 ± 1.02 mg bird-1 hr-1 respectively, and 0.21 ± 0.28 mg bird-1 hr-1 from the layer barn. Carbon dioxide emission factors from the broiler barns with mud and cement floors were 9327 ± 3508 and 25526 ± 6904 mg bird-1 hr-1 respectively, and 8942 ± 36756 mg bird-1 hr-1 from the layer barn. When scaled per livestock unit (LU), where 1 LU is 500 kg bird weight, CH4 emissions were 0.16 ± 0.17 and 0.06 ± 0.03 g LU-1 hr-1 from the broiler barns, and 0.19 ± 0.14 g LU-1 hr-1 from the layer barn. Nitrous oxide emissions were 2.16 ± 1.69 and 0.28 ± 0.17 g LU-1 hr-1 from the broiler barns, and 0.05 ± 0.07 g LU-1 hr-1 from the layer barn. Broilers reared in management systems with wood shavings on mud floor had relatively high CH4 and N2O emissions compared to broilers on wood shavings and cement floor, with the contrary observed for CO2. The emissions N2O were significantly higher from broiler barns compared to layer barns. Emissions were higher in the mornings compared to later periods of the day. Given the observed results, GHG emission mitigation strategies need to be customised for each building design and management system.
-
Energy Technology Data Exchange (ETDEWEB)
Friedrich, Elena, E-mail: Friedriche@ukzn.ac.za; Trois, Cristina
2013-11-15
Highlights: • GHG emission factors for local recycling of municipal waste are presented. • GHG emission factors for two composting technologies for garden waste are included. • Local GHG emission factors were compared to international ones and discussed. • Uncertainties and limitations are presented and areas for new research highlighted. - Abstract: GHG (greenhouse gas) emission factors for waste management are increasingly used, but such factors are very scarce for developing countries. This paper shows how such factors have been developed for the recycling of glass, metals (Al and Fe), plastics and paper from municipal solid waste, as well as for the composting of garden refuse in South Africa. The emission factors developed for the different recyclables in the country show savings varying from −290 kg CO{sub 2} e (glass) to −19 111 kg CO{sub 2} e (metals – Al) per tonne of recyclable. They also show that there is variability, with energy intensive materials like metals having higher GHG savings in South Africa as compared to other countries. This underlines the interrelation of the waste management system of a country/region with other systems, in particular with energy generation, which in South Africa, is heavily reliant on coal. This study also shows that composting of garden waste is a net GHG emitter, releasing 172 and 186 kg CO{sub 2} e per tonne of wet garden waste for aerated dome composting and turned windrow composting, respectively. The paper concludes that these emission factors are facilitating GHG emissions modelling for waste management in South Africa and enabling local municipalities to identify best practice in this regard.
-
International Nuclear Information System (INIS)
Friedrich, Elena; Trois, Cristina
2013-01-01
Highlights: • GHG emission factors for local recycling of municipal waste are presented. • GHG emission factors for two composting technologies for garden waste are included. • Local GHG emission factors were compared to international ones and discussed. • Uncertainties and limitations are presented and areas for new research highlighted. - Abstract: GHG (greenhouse gas) emission factors for waste management are increasingly used, but such factors are very scarce for developing countries. This paper shows how such factors have been developed for the recycling of glass, metals (Al and Fe), plastics and paper from municipal solid waste, as well as for the composting of garden refuse in South Africa. The emission factors developed for the different recyclables in the country show savings varying from −290 kg CO 2 e (glass) to −19 111 kg CO 2 e (metals – Al) per tonne of recyclable. They also show that there is variability, with energy intensive materials like metals having higher GHG savings in South Africa as compared to other countries. This underlines the interrelation of the waste management system of a country/region with other systems, in particular with energy generation, which in South Africa, is heavily reliant on coal. This study also shows that composting of garden waste is a net GHG emitter, releasing 172 and 186 kg CO 2 e per tonne of wet garden waste for aerated dome composting and turned windrow composting, respectively. The paper concludes that these emission factors are facilitating GHG emissions modelling for waste management in South Africa and enabling local municipalities to identify best practice in this regard
-
Christen, Andreas; Johnson, Mark; Molodovskaya, Marina; Ketler, Rick; Nesic, Zoran; Crawford, Ben; Giometto, Marco; van der Laan, Mike
2013-04-01
The most important long-lived greenhouse gas (LLGHG) emitted during combustion of fuels is carbon dioxide (CO2), however also traces of the LLGHGs methane (CH4) and nitrous oxide (N2O) are released, the quantities of which depend largely on the conditions of the combustion process. Emission factors determine the mass of LLGHGs emitted per energy used (or kilometre driven for cars) and are key inputs for bottom-up emission modelling. Emission factors for CH4 are typically determined in the laboratory or on a test stand for a given combustion system using a small number of samples (vehicles, furnaces), yet associated with larger uncertainties when scaled to entire fleets. We propose an alternative, different approach - Can integrated emission factors be independently determined using direct micrometeorological flux measurements over an urban surface? If so, do emission factors determined from flux measurements (top-down) agree with up-scaled emission factors of relevant combustion systems (heating, vehicles) in the source area of the flux measurement? Direct flux measurements of CH4 were carried out between February and May, 2012 over a relatively densely populated, urban surface in Vancouver, Canada by means of eddy covariance (EC). The EC-system consisted of an ultrasonic anemometer (CSAT-3, Campbell Scientific Inc.) and two open-path infrared gas analyzers (Li7500 and Li7700, Licor Inc.) on a tower at 30m above the surface. The source area of the EC system is characterised by a relative homogeneous morphometry (5.3m average building height), but spatially and temporally varying emission sources, including two major intersecting arterial roads (70.000 cars drive through the 50% source area per day) and seasonal heating in predominantly single-family houses (natural gas). An inverse dispersion model (turbulent source area model), validated against large eddy simulations (LES) of the urban roughness sublayer, allows the determination of the spatial area that
-
Novel method for on-road emission factor measurements using a plume capture trailer.
Morawska, L; Ristovski, Z D; Johnson, G R; Jayaratne, E R; Mengersen, K
2007-01-15
The method outlined provides for emission factor measurements to be made for unmodified vehicles driving under real world conditions at minimal cost. The method consists of a plume capture trailer towed behind a test vehicle. The trailer collects a sample of the naturally diluted plume in a 200 L conductive bag and this is delivered immediately to a mobile laboratory for subsequent analysis of particulate and gaseous emissions. The method offers low test turnaround times with the potential to complete much larger numbers of emission factor measurements than have been possible using dynamometer testing. Samples can be collected at distances up to 3 m from the exhaust pipe allowing investigation of early dilution processes. Particle size distribution measurements, as well as particle number and mass emission factor measurements, based on naturally diluted plumes are presented. A dilution profile relating the plume dilution ratio to distance from the vehicle tail pipe for a diesel passenger vehicle is also presented. Such profiles are an essential input for new mechanistic roadway air quality models.
-
40 CFR 63.5758 - How do I determine the organic HAP content of materials?
2010-07-01
... operations and use that value as a substitute for mass fraction of organic HAP. (4) Alternative method. You... for each material used in your open molding resin and gel coat operations, carpet and fabric adhesive operations, or aluminum recreational boat surface coating operations, you must use one of the options in...
-
Directory of Open Access Journals (Sweden)
Alfonso Quijano Parra
Full Text Available En los últimos tiempos ha tomado un gran auge en los países del tercer mundo, incluidos los de América Latina, el estudio de la exposición humana a las emisiones de combustión, incluyendo las partículas ultrafinas (PM2,5 y componentes mutagénicos y carcinógenos como los hidrocarburos aromáticos policíclicos (HAPs. En este trabajo se identificó en la ciudad de Cúcuta un grupo de HAPs reconocidos por su afectación a la salud de la población; los HAPs encontrados fueron: metilcriseno, benzo[a]antraceno, benzo[j]fluoranteno, benzo[b]fluoranteno, benzo[a]pireno, dibenzo[a,l]pireno, dibenzo[a,e]pireno, benzo[c]fluoreno, benzo[k]fluoranteno, Indeno[1,2,3-cd]pireno, dibenzo[a,h]antraceno y benzo[g,h.i]perileno. Adicionalmente también se evaluó in vitro usando el ensayo cometa, el efecto genotóxico del material particulado PM2,5 extraído con acetona y diclorometano.
-
Frey, H Christopher; Bammi, Sachin
2002-04-01
Variability refers to real differences in emissions among multiple emission sources at any given time or over time for any individual emission source. Variability in emissions can be attributed to variation in fuel or feedstock composition, ambient temperature, design, maintenance, or operation. Uncertainty refers to lack of knowledge regarding the true value of emissions. Sources of uncertainty include small sample sizes, bias or imprecision in measurements, nonrepresentativeness, or lack of data. Quantitative methods for characterizing both variability and uncertainty are demonstrated and applied to case studies of emission factors for lawn and garden (L&G) equipment engines. Variability was quantified using empirical and parametric distributions. Bootstrap simulation was used to characterize confidence intervals for the fitted distributions. The 95% confidence intervals for the mean grams per brake horsepower/hour (g/hp-hr) emission factors for two-stroke engine total hydrocarbon (THC) and NOx emissions were from -30 to +41% and from -45 to +75%, respectively. The confidence intervals for four-stroke engines were from -33 to +46% for THCs and from -27 to +35% for NOx. These quantitative measures of uncertainty convey information regarding the quality of the emission factors and serve as a basis for calculation of uncertainty in emission inventories (EIs).
-
2010-07-01
... Reconstructed 2SLB and Compression Ignition Stationary RICE >500 HP and New and Reconstructed 4SLB Stationary RICE â¥250 HP Located at a Major Source of HAP Emissions 2a Table 2a to Subpart ZZZZ of Part 63... 2SLB and Compression Ignition Stationary RICE >500 HP and New and Reconstructed 4SLB Stationary RICE...
-
Lee, Taewoo; Park, Junhong; Kwon, Sangil; Lee, Jongtae; Kim, Jeongsoo
2013-09-01
The objective of this study is to quantify the differences in NO(x) emissions between standard and non-standard driving and vehicle operating conditions, and to estimate by how much NO(x) emissions exceed the legislative emission limits under typical Korean road traffic conditions. Twelve Euro 3-5 light-duty diesel vehicles (LDDVs) manufactured in Korea were driven on a chassis dynamometer over the standard New European Driving Cycle (NEDC) and a representative Korean on-road driving cycle (KDC). NO(x) emissions, average speeds and accelerations were calculated for each 1-km trip segment, so called averaging windows. The results suggest that the NO(x) emissions of the tested vehicles are more susceptible to variations in the driving cycles than to those in the operating conditions. Even under comparable operating conditions, the NO(x) control capabilities of vehicles differ from each other, i.e., NO(x) control is weaker for the KDC than for the NEDC. The NO(x) emissions over the KDC for given vehicle operating conditions exceed those over the NEDC by more than a factor of 8. Consequently, on-road NO(x) emission factors are estimated here to exceed the Euro 5 emission limit by up to a factor of 8, 4 and 3 for typical Korean urban, rural, and motorway road traffic conditions, respectively. Our findings support the development of technical regulations for supplementary real-world emission tests for emission certification and the corresponding research actions taken by automotive industries. Copyright © 2013 Elsevier B.V. All rights reserved.
-
Directory of Open Access Journals (Sweden)
Franke Andre
2010-12-01
Full Text Available Abstract Background Expression levels for 47294 transcripts in lymphoblastoid cell lines from all 270 HapMap phase II individuals, and genotypes (both HapMap phase II and III of 3.96 million single nucleotide polymorphisms (SNPs in the same individuals are publicly available. We aimed to generate a user-friendly web based tool for visualization of the correlation between SNP genotypes within a specified genomic region and a gene of interest, which is also well-known as an expression quantitative trait locus (eQTL analysis. Results SNPexp is implemented as a server-side script, and publicly available on this website: http://tinyurl.com/snpexp. Correlation between genotype and transcript expression levels are calculated by performing linear regression and the Wald test as implemented in PLINK and visualized using the UCSC Genome Browser. Validation of SNPexp using previously published eQTLs yielded comparable results. Conclusions SNPexp provides a convenient and platform-independent way to calculate and visualize the correlation between HapMap genotypes within a specified genetic region anywhere in the genome and gene expression levels. This allows for investigation of both cis and trans effects. The web interface and utilization of publicly available and widely used software resources makes it an attractive supplement to more advanced bioinformatic tools. For the advanced user the program can be used on a local computer on custom datasets.
-
Cheng, Chih-Wen; Hua, Jian; Hwang, Daw-Shang
2017-10-01
An important marine pollution issue identified by the International Maritime Organization (IMO) is NO x emissions; however, the stipulated method for determining the NO x certification value does not reflect the actual high emission factors of slow-speed two-stroke diesel engines over long-term slow steaming. In this study, an accurate method is presented for calculating the NO x emission factors and total amount of NO x emissions by using the actual power probabilities of the diesel engines in four types of bulk carriers. The proposed method is suitable for all types and purposes of diesel engines, is not restricted to any operating modes, and is highly accurate. Moreover, it is recommended that the IMO-stipulated certification value calculation method be modified accordingly to genuinely reduce the amount of NO x emissions. The successful achievement of this level of reduction will help improve the air quality, especially in coastal and port areas, and the health of local residents. As per the IMO, the NO x emission certification value of marine diesel engines having a rated power over 130 kW must be obtained using specified weighting factor (WF)-based calculation. However, this calculation fails to represent the current actual situation. Effective emission reductions of 6.91% (at sea) and 31.9% (in ports) were achieved using a mathematical model of power probability functions. Thus, we strongly recommend amending the certification value of NO x Technical Code 2008 (NTC 2008) by removing the WF constraints, such that the NO x emissions of diesel engines is lower than the Tier-limits at any load level to obtain genuine NO x emission reductions.
-
Transport sector CO{sub 2} emissions growth in Asia: Underlying factors and policy options
Energy Technology Data Exchange (ETDEWEB)
Timilsina, Govinda R., E-mail: gtimilsina@worldbank.or [Development Research Group, World Bank, 1818H Street, NW, Washington, DC 20433 (United States); Shrestha, Ashish [Development Research Group, World Bank, 1818H Street, NW, Washington, DC 20433 (United States)
2009-11-15
This study analyze the potential factors influencing the growth of transport sector carbon dioxide (CO{sub 2}) emissions in selected Asian countries during the 1980-2005 period by decomposing annual emissions growth into components representing changes in fuel mix, modal shift, per capita gross domestic product (GDP) and population, as well as changes in emission coefficients and transportation energy intensity. We find that changes in per capita GDP, population growth and transportation energy intensity are the main factors driving transport sector CO{sub 2} emission growth in the countries considered. While growth in per capita income and population are responsible for the increasing trend of transport sector CO{sub 2} emissions in China, India, Indonesia, Republic of Korea, Malaysia, Pakistan, Sri Lanka and Thailand; the decline of transportation energy intensity is driving CO{sub 2} emissions down in Mongolia. Per capita GDP, population and transportation energy intensity effects are all found responsible for transport sector CO{sub 2} emissions growth in Bangladesh, the Philippines and Vietnam. The study also reviews existing government policies to limit CO{sub 2} emissions growth, such as fiscal instruments, fuel economy standards and policies to encourage switching to less emission intensive fuels and transportation modes.
-
Transport sector CO{sub 2} emissions growth in Asia. Underlying factors and policy options
Energy Technology Data Exchange (ETDEWEB)
Timilsina, Govinda R.; Shrestha, Ashish [Development Research Group, The World Bank, 1818H Street, NW, Washington, DC 20433 (United States)
2009-11-15
This study analyze the potential factors influencing the growth of transport sector carbon dioxide (CO{sub 2}) emissions in selected Asian countries during the 1980-2005 period by decomposing annual emissions growth into components representing changes in fuel mix, modal shift, per capita gross domestic product (GDP) and population, as well as changes in emission coefficients and transportation energy intensity. We find that changes in per capita GDP, population growth and transportation energy intensity are the main factors driving transport sector CO{sub 2} emission growth in the countries considered. While growth in per capita income and population are responsible for the increasing trend of transport sector CO{sub 2} emissions in China, India, Indonesia, Republic of Korea, Malaysia, Pakistan, Sri Lanka and Thailand; the decline of transportation energy intensity is driving CO{sub 2} emissions down in Mongolia. Per capita GDP, population and transportation energy intensity effects are all found responsible for transport sector CO{sub 2} emissions growth in Bangladesh, the Philippines and Vietnam. The study also reviews existing government policies to limit CO{sub 2} emissions growth, such as fiscal instruments, fuel economy standards and policies to encourage switching to less emission intensive fuels and transportation modes. (author)
-
Winkler, H; Adam, G; Mattes, E; Schanz, M; Hartig, A; Ruis, H
1988-01-01
Control of expression of the Saccharomyces cerevisiae CTT1 (catalase T) gene by the HAP1 (CYP1) gene, a mediator of heme control of mitochondrial cytochromes, was studied. Expression of a CTT1-lacZ fusion in a hap1 mutant showed that the CTT1 promoter is under HAP1 control. As demonstrated by a gel retardation assay, the HAP1 protein binds to a heme control region of the CTT1 gene. This binding in vitro is stimulated by hemin. The HAP1-binding sequence was localized by using DNA fragments spanning different regions, by DNase I footprinting and by methylation interference of DNA-protein binding. The binding site was compared to the HAP1-binding sequences previously characterized in detail (UAS1CYC1, UASCYC7). There is strikingly little similarity between the three sequences, which have only four of those 23 bp in common which are protected from DNase I digestion. However, the pattern of major and minor groove contacts in the complex is quite similar in all three cases. The results obtained show that there is true co-ordinate control of expression of mitochondrial cytochromes and at least some extra-mitochondrial hemoproteins. Heme acts as a metabolic signal in this coordination, which is mediated by the HAP1 protein. Images PMID:2844525
-
Pühapäeva hommik : [luuletused] / Wallace Stevens ; tõlk. Hasso Krull, Märt Väljataga
Stevens, Wallace
2008-01-01
Sisu: Pühapäeva hommik ; Peter Quince klahvide ees ; Mozart, 1935 ; Postkaart vulkaanist ; Moodsast luulest ; Paks punane mees loeb ette ; Seesmise armukese viimane üksikõne ; Ühe üksikasja kulg. Elu- ja loomeloolisi andmeid autori kohta lk. 531-532
-
The influencing factors of CO2 emission intensity of Chinese agriculture from 1997 to 2014.
Long, Xingle; Luo, Yusen; Wu, Chao; Zhang, Jijian
2018-05-01
In China, agriculture produces the greatest chemical oxygen demand (COD) emissions in wastewater and the most methane (CH 4 ) emissions. It is imperative that agricultural pollution in China be reduced. This study investigated the influencing factors of the CO 2 emission intensity of Chinese agriculture from 1997 to 2014. We analyzed the influencing factors of the CO 2 emission intensity through the first-stage least-square regression. We also analyzed determinants of innovation through the second-stage least-square regression. We found that innovation negatively affected the CO 2 emission intensity in the model of the nation. FDI positively affected innovation in China. It is important to enhance indigenous innovation for green agriculture through labor training and collaboration between agriculture and academia.
-
GLIDERS - A web-based search engine for genome-wide linkage disequilibrium between HapMap SNPs
Directory of Open Access Journals (Sweden)
Broxholme John
2009-10-01
Full Text Available Abstract Background A number of tools for the examination of linkage disequilibrium (LD patterns between nearby alleles exist, but none are available for quickly and easily investigating LD at longer ranges (>500 kb. We have developed a web-based query tool (GLIDERS: Genome-wide LInkage DisEquilibrium Repository and Search engine that enables the retrieval of pairwise associations with r2 ≥ 0.3 across the human genome for any SNP genotyped within HapMap phase 2 and 3, regardless of distance between the markers. Description GLIDERS is an easy to use web tool that only requires the user to enter rs numbers of SNPs they want to retrieve genome-wide LD for (both nearby and long-range. The intuitive web interface handles both manual entry of SNP IDs as well as allowing users to upload files of SNP IDs. The user can limit the resulting inter SNP associations with easy to use menu options. These include MAF limit (5-45%, distance limits between SNPs (minimum and maximum, r2 (0.3 to 1, HapMap population sample (CEU, YRI and JPT+CHB combined and HapMap build/release. All resulting genome-wide inter-SNP associations are displayed on a single output page, which has a link to a downloadable tab delimited text file. Conclusion GLIDERS is a quick and easy way to retrieve genome-wide inter-SNP associations and to explore LD patterns for any number of SNPs of interest. GLIDERS can be useful in identifying SNPs with long-range LD. This can highlight mis-mapping or other potential association signal localisation problems.
-
Energy Technology Data Exchange (ETDEWEB)
Roh, Hee-Sang [Department of Dental Materials, School of Dentistry, Chosun University, 309 Pilmun-daero, Dong-gu, Gwangju 61452 (Korea, Republic of); Jung, Sang-Chul [Department of Environmental Engineering, Sunchon National University, 255 Jungang-ro, Sunchon 57922 (Korea, Republic of); Kook, Min-Suk [Department of Oral and Maxillofacial Surgery, School of Dentistry, Chonnam National University, 77 Yongbong-ro, Buk-gu, Gwangju 61186 (Korea, Republic of); Kim, Byung-Hoon, E-mail: kim5055@chosun.ac.kr [Department of Dental Materials, School of Dentistry, Chosun University, 309 Pilmun-daero, Dong-gu, Gwangju 61452 (Korea, Republic of)
2016-12-01
Highlights: • PLGA and PLGA/n-HAp/β-TCP scaffolds were successfully fabricated by 3D printing. • Oxygen plasma etching increases the wettability and surface roughness. • Bioceramics and oxygen plasma etching and could be used to improve the cell affinity. - Abstract: Three-dimensional (3D) scaffolds have many advantageous properties for bone tissue engineering application, due to its controllable properties such as pore size, structural shape and interconnectivity. In this study, effects on oxygen plasma surface modification and adding of nano-hydroxyapatite (n-HAp) and β-tricalcium phosphate (β-TCP) on the 3D PLGA/n-HAp/β-TCP scaffolds for improving preosteoblast cell (MC3T3-E1) adhesion, proliferation and differentiation were investigated. The 3D PLGA/n-HAp/β-TCP scaffolds were fabricated by 3D Bio-Extruder equipment. The 3D scaffolds were prepared with 0°/90° architecture and pore size of approximately 300 μm. In addition 3D scaffolds surface were etched by oxygen plasma to enhance the hydrophilic property and surface roughness. After oxygen plasma treatment, the surface chemistry and morphology were investigated by Fourier transform infrared spectroscopy, scanning electron microscopy, and atomic force microscopy. And also hydrophilic property was measured by contact angle. The MC3T3-E1 cell proliferation and differentiation were investigated by MTT assay and ALP activity. In present work, the 3D PLGA/HAp/beta-TCP composite scaffold with suitable structure for the growth of osteoblast cells was successfully fabricated by 3D rapid prototyping technique. The surface hydrophilicity and roughness of 3D scaffold increased by oxygen plasma treatment had a positive effect on cell adhesion, proliferation, and differentiation. Furthermore, the differentiation of MC3T3-E1 cell was significantly enhanced by adding of n-HAp and β-TCP on 3D PLGA scaffold. As a result, combination of bioceramics and oxygen plasma treatment showed a synergistic effect on
-
Tabatabaee, Akram; Siadat, Seyed Davar; Moosavi, Seyed Fazllolah; Aghasadeghi, Mohammad Reza; Memarnejadian, Arash; Pouriayevali, Mohammad Hassan; Yavari, Neda
2013-01-01
Background Nontypeable Haemophilus influenzae (NTHi) is a common cause of respiratory tract disease and initiates infection by colonization in nasopharynx. The Haemophilus influenzae (H. influenzae) Hap adhesin is an auto transporter protein that promotes initial interaction with human epithelial cells. Hap protein contains a 110 kDa internal passenger domain called “HapS” and a 45 kDa C-terminal translocator domain called “Hapβ”. Hap adhesive activity has been recently reported to be connected to its Cell Binding Domain (CBD) which resides within the 311 C-terminal residues of the internal passenger domain of the protein. Furthermore, immunization with this CBD protein has been shown to prevent bacterial nasopharynx colonization in animal models. Methods To provide enough amounts of pure HapS protein for vaccine studies, we sought to develop a highly optimized system to overexpress and purify the protein in large quantities. To this end, pET24a-cbd plasmid harboring cbd sequence from NTHi ATCC49766 was constructed and its expression was optimized by testing various expression parameters such as growth media, induction temperature, IPTG inducer concentration, induction stage and duration. SDS-PAGE and Western-blotting were used for protein analysis and confirmation and eventually the expressed protein was easily purified via immobilized metal affinity chromatography (IMAC) using Ni-NTA columns. Results The highest expression level of target protein was achieved when CBD expressing E. coli BL21 (DE3) cells were grown at 37°C in 2xTY medium with 1.0 mM IPTG at mid-log phase (OD600 nm equal to 0.6) for 5 hrs. Amino acid sequence alignment of expressed CBD protein with 3 previously published CBD amino acid sequences were more than %97 identical and antigenicity plot analysis further revealed 9 antigenic domains which appeared to be well conserved among different analyzed CBD sequences. Conclusion Due to the presence of high similarity among CBD from NTHi ATCC
-
Energy Technology Data Exchange (ETDEWEB)
Krol, D.J., E-mail: kroldj@tcd.ie [Teagasc, Crops, Land Use and Environment Programme, Johnstown Castle, Co., Wexford (Ireland); Carolan, R. [Agri-Food and Biosciences Institute (AFBI), Belfast BT9 5PX (Ireland); Minet, E. [Teagasc, Crops, Land Use and Environment Programme, Johnstown Castle, Co., Wexford (Ireland); McGeough, K.L.; Watson, C.J. [Agri-Food and Biosciences Institute (AFBI), Belfast BT9 5PX (Ireland); Forrestal, P.J. [Teagasc, Crops, Land Use and Environment Programme, Johnstown Castle, Co., Wexford (Ireland); Lanigan, G.J., E-mail: gary.lanigan@teagasc.ie [Teagasc, Crops, Land Use and Environment Programme, Johnstown Castle, Co., Wexford (Ireland); Richards, K.G. [Teagasc, Crops, Land Use and Environment Programme, Johnstown Castle, Co., Wexford (Ireland)
2016-10-15
Cattle excreta deposited on grazed grasslands are a major source of the greenhouse gas (GHG) nitrous oxide (N{sub 2}O). Currently, many countries use the IPCC default emission factor (EF) of 2% to estimate excreta-derived N{sub 2}O emissions. However, emissions can vary greatly depending on the type of excreta (dung or urine), soil type and timing of application. Therefore three experiments were conducted to quantify excreta-derived N{sub 2}O emissions and their associated EFs, and to assess the effect of soil type, season of application and type of excreta on the magnitude of losses. Cattle dung, urine and artificial urine treatments were applied in spring, summer and autumn to three temperate grassland sites with varying soil and weather conditions. Nitrous oxide emissions were measured from the three experiments over 12 months to generate annual N{sub 2}O emission factors. The EFs from urine treated soil was greater (0.30–4.81% for real urine and 0.13–3.82% for synthetic urine) when compared with dung (− 0.02–1.48%) treatments. Nitrous oxide emissions were driven by environmental conditions and could be predicted by rainfall and temperature before, and soil moisture deficit after application; highlighting the potential for a decision support tool to reduce N{sub 2}O emissions by modifying grazing management based on these parameters. Emission factors varied seasonally with the highest EFs in autumn and were also dependent on soil type, with the lowest EFs observed from well-drained and the highest from imperfectly drained soil. The EFs averaged 0.31 and 1.18% for cattle dung and urine, respectively, both of which were considerably lower than the IPCC default value of 2%. These results support both lowering and disaggregating EFs by excreta type. - Highlights: • N{sub 2}O emissions were measured from cattle excreta applied to pasture. • N{sub 2}O was universally higher from urine compared with dung. • N{sub 2}O was driven by rainfall, temperature
-
Energy Technology Data Exchange (ETDEWEB)
Sakai, Shin-ichi; Hirai, Yasuhiro [National Institute for Environmental Studies, Tsukuba (Japan); Ota, Shizuko; Sudo, Kinichi [Ministry of Environment (Japan)
2004-09-15
With regard to polybrominated diphenyl ether (PBDE), there is few scientific knowledge on the emission patterns into the environment and exposure pathways to humans, and basic information is insufficient to consider what measures effective are. For the purpose of promoting risk reduction of target substances more effectively and efficiently, it is desirable to comprehend accurately the causal chain from the target substances utilization to the risk intake, and to evaluate the measures covering the whole applications of target substances. As the existing researches on the PBDE emission inventory, there are EU risk assessment report (European Chemical Bureau 2000, 2002, 2003), Danish EPA (1999), Palm et al.(2002) and Alcock et al. (2003). In addition, emissions of DecaBDE are published in TRI (Toxic Release Inventory) of US EPA. However, the primary information of the previous inventories is often the same and estimations based on the measured values are few. In light of the situation, PBDE emission concentrations from processing facilities of flame retardant plastics and recycling facilities of home electric appliances are measured in practice to presume material flow of PBDE and to estimate emission factors and inventories from each phase of life cycles. The validities of emission factors are examined in comparison to measured values of atmospheric depositions surroundings, which are close to sources.
-
Wadden, R A; Hawkins, J L; Scheff, P A; Franke, J E
1991-09-01
A study at an automotive parts fabrication plant evaluated four metal surface treatment processes during production conditions. The evaluation provides examples of how to estimate process emission factors from activity and air concentration data. The processes were open tank and enclosed tank degreasing with trichloroethylene (TCE), chromium conversion coating, and chromium electroplating. Area concentrations of TCE and chromium (Cr) were monitored for 1-hr periods at three distances from each process. Source activities at each process were recorded during each sampling interval. Emission rates were determined by applying appropriate mass balance models to the concentration patterns around each source. The emission factors obtained from regression analysis of the emission rate and activity data were 16.9 g TCE/basket of parts for the open-top degreaser; 1.0 g TCE/1000 parts for the enclosed degreaser; 1.48-1.64 mg Cr/1000 parts processed in the hot CrO3/HNO3 tank for the chrome conversion coating; and 5.35-9.17 mg Cr/rack of parts for chrome electroplating. The factors were also used to determine the efficiency of collection for the local exhaust systems serving each process. Although the number of observations were limited, these factors may be useful for providing initial estimates of emissions from similar processes in other settings.
-
N2O emission hotspots at different spatial scales and governing factors for small scale hotspots
International Nuclear Information System (INIS)
Heuvel, R.N. van den; Hefting, M.M.; Tan, N.C.G.; Jetten, M.S.M.; Verhoeven, J.T.A.
2009-01-01
Chronically nitrate-loaded riparian buffer zones show high N 2 O emissions. Often, a large part of the N 2 O is emitted from small surface areas, resulting in high spatial variability in these buffer zones. These small surface areas with high N 2 O emissions (hotspots) need to be investigated to generate knowledge on the factors governing N 2 O emissions. In this study the N 2 O emission variability was investigated at different spatial scales. Therefore N 2 O emissions from three 32 m 2 grids were determined in summer and winter. Spatial variation and total emission were determined on three different scales (0.3 m 2 , 0.018 m 2 and 0.0013 m 2 ) at plots with different levels of N 2 O emissions. Spatial variation was high at all scales determined and highest at the smallest scale. To test possible factors inducing small scale hotspots, soil samples were collected for slurry incubation to determine responses to increased electron donor/acceptor availability. Acetate addition did increase N 2 O production, but nitrate addition failed to increase total denitrification or net N 2 O production. N 2 O production was similar in all soil slurries, independent of their origin from high or low emission soils, indicating that environmental conditions (including physical factors like gas diffusion) rather than microbial community composition governed N 2 O emission rates
-
HOT SPOT RELIEF WITH EMBEDDED BEAM FOR CDMA SYSTEMS IN HAPS
Institute of Scientific and Technical Information of China (English)
无
2006-01-01
This paper proposes a novel micro/macro beam coverage scheme used in High Altitude Platform System (HAPS) Code Division Multiple Access (CDMA) systems. A relief of traffic burden in hot spot areas is achieved by embedding micro-beams into the macro-beams at the hot spot locations, together with appropriate power ratio control and user ratio control. The simulation results show that the hot spot problem can be relieved efficiently with the presented configuration, and a higher and more stable system capacity is expectable despite the variation of user distribution.
-
International Nuclear Information System (INIS)
Mikols, E.H.; Gill, A.S.; Dougherty, A.
1996-01-01
Title III of the 1990 Clean Air Act Amendments (CAAA) addresses the control of hazardous air pollutants (HAPs) from major sources of air pollution in the US. In the CAAA, Congress defined 189 compounds as hazardous air pollutants in need of additional control by the Environmental Protection Agency (EPA). Congress directed EPA to identify the major source categories which emit HAPs and to prepare regulations that would reduce and control future HAP emissions. This paper outlines the activities undertaken by EPA to regulate HAP emissions from Portland cement plants and the program developed by the Portland cement manufacturing industry to cope with Title III
-
Unexpected Relationships and Inbreeding in HapMap Phase III Populations
Stevens, Eric L.; Baugher, Joseph D.; Shirley, Matthew D.; Frelin, Laurence P.; Pevsner, Jonathan
2012-01-01
Correct annotation of the genetic relationships between samples is essential for population genomic studies, which could be biased by errors or omissions. To this end, we used identity-by-state (IBS) and identity-by-descent (IBD) methods to assess genetic relatedness of individuals within HapMap phase III data. We analyzed data from 1,397 individuals across 11 ethnic populations. Our results support previous studies (Pemberton et al., 2010; Kyriazopoulou-Panagiotopoulou et al., 2011) assessing unknown relatedness present within this population. Additionally, we present evidence for 1,657 novel pairwise relationships across 9 populations. Surprisingly, significant Cotterman's coefficients of relatedness K1 (IBD1) values were detected between pairs of known parents. Furthermore, significant K2 (IBD2) values were detected in 32 previously annotated parent-child relationships. Consistent with a hypothesis of inbreeding, regions of homozygosity (ROH) were identified in the offspring of related parents, of which a subset overlapped those reported in previous studies (Gibson et al. 2010; Johnson et al. 2011). In total, we inferred 28 inbred individuals with ROH that overlapped areas of relatedness between the parents and/or IBD2 sharing at a different genomic locus between a child and a parent. Finally, 8 previously annotated parent-child relationships had unexpected K0 (IBD0) values (resulting from a chromosomal abnormality or genotype error), and 10 previously annotated second-degree relationships along with 38 other novel pairwise relationships had unexpected IBD2 (indicating two separate paths of recent ancestry). These newly described types of relatedness may impact the outcome of previous studies and should inform the design of future studies relying on the HapMap Phase III resource. PMID:23185369
-
van Maris, A.J.A.; Bakker, B.M.; Brandt, M.; Boorsma, A.; Teixeira de Mattos, M.J.; Grivell, L.A.; Pronk, J.T.
2001-01-01
The tendency of Saccharomyces cerevisiae to favor alcoholic fermentation over respiration is a complication in aerobic, biomass-directed applications of this yeast. Overproduction of Hap4p, a positive transcriptional regulator of genes involved in respiratory metabolism, has been reported to
-
Quiros, David C; Smith, Jeremy D; Ham, Walter A; Robertson, William H; Huai, Tao; Ayala, Alberto; Hu, Shaohua
2018-04-13
Remote sensing devices have been used for decades to measure gaseous emissions from individual vehicles at the roadside. Systems have also been developed that entrain diluted exhaust and can also measure particulate matter (PM) emissions. In 2015, the California Air Resources Board (CARB) reported that 8% of in-field diesel particulate filters (DPF) on heavy-duty (HD) vehicles were malfunctioning and emitted about 70% of total diesel PM emissions from the DPF-equipped fleet. A new high-emitter problem in the heavy-duty vehicle fleet had emerged. Roadside exhaust plume measurements reflect a snapshot of real-world operation, typically lasting several seconds. In order to relate roadside plume measurements to laboratory emission tests, we analyzed carbon dioxide (CO 2 ), oxides of nitrogen (NO X ), and PM emissions collected from four HD vehicles during several driving cycles on a chassis dynamometer. We examined the fuel-based emission factors corresponding to possible exceedances of emission standards as a function of vehicle power. Our analysis suggests that a typical HD vehicle will exceed the model year (MY) 2010 emission standards (of 0.2 g NO X /bhp-hr and 0.01 g PM/bhp-hr) by three times when fuel-based emission factors are 9.3 g NO X /kg fuel and 0.11 g PM/kg using the roadside plume measurement approach. Reported limits correspond to 99% confidence levels, which were calculated using the detection uncertainty of emissions analyzers, accuracy of vehicle power calculations, and actual emissions variability of fixed operational parameters. The PM threshold was determined for acceleration events between 0.47 and 1.4 mph/sec only, and the NO X threshold was derived from measurements where aftertreatment temperature was above 200°C. Anticipating a growing interest in real-world driving emissions, widespread implementation of roadside exhaust plume measurements as a compliment to in-use vehicle programs may benefit from expanding this analysis to a larger
-
International Nuclear Information System (INIS)
Atimtay, Aysel T.
2003-01-01
World primary energy demand increases with increases in population and economic development. Within the last 25 yr, the total energy consumption has almost doubled. For the purpose of meeting this demand, fossil energy sources are used and various pollutants are generated. CO 2 is also one of these gases, which cannot be removed like other pollutants, and it causes greenhouse effect and climate change. Reducing the CO 2 emission is very important because of the environmental concerns and regulations, especially the Kyoto Protocol. This paper reviews the estimated world carbon emissions, Turkey's situation in electrical energy production, emission amounts estimated until the year 2020 and emission factors for dust, SO 2 , NO x and CO 2 . The estimated results show that CO 2 emissions from thermal power plants in Turkey will make about 0.66 % of the global CO 2 emissions in 2020
-
2010-07-01
... Continuous Lamination Lines and Continuous Casting Lines Complying With a Lbs/Ton Organic HAP Emissions Limit... Requirements for New and Existing Continuous Lamination Lines and Continuous Casting Lines Complying With a Lbs... with a lbs/ton organic HAP emissions limit for continuous lamination lines and continuous casting lines...
-
HDPE-Al2O3-HAp composites for biomedical applications: processing and characterizations.
Nath, Shekhar; Bodhak, Subhadip; Basu, Bikramjit
2009-01-01
The objective of this work is to demonstrate how the stiffness, hardness, as well as the biocompatibility property, of bioinert high-density polyethylene (HDPE) can be significantly improved by the combined addition of both bioinert and bioactive ceramic fillers. For this purpose, different volume fractions of hydroxyapatite and alumina, limited to a total of 40 vol %, have been incorporated in HDPE matrix. All the hybrid composites and monolithic HDPE were developed under optimized hot pressing condition (130 degrees C, 0.5 h, 92 MPa pressure). The results of the mechanical property characterization reveal that higher elastic modulus (6.2 GPa) and improved hardness (226.5 MPa) could be obtained in the developed HDPE-20 vol %-HAp-20 vol % Al(2)O(3) composite. Under the selected fretting conditions against various counterbody materials (steel, Al(2)O(3), and ZrO(2)), an extremely low COF of (0.07-0.11) and higher wear resistance (order of 10(-6) mm(3)/Nm) are obtained with the HDPE/20 vol % HAp/20 vol % Al(2)O(3) composite in both air and simulated body fluid environment. Importantly, in-vitro cell culture study using L929 fibroblast cells confirms favorable cell adhesion properties in the developed hybrid composite. (c) 2008 Wiley Periodicals, Inc.
-
Abtahi, Mehrnoosh; Koolivand, Ali; Dobaradaran, Sina; Yaghmaeian, Kamyar; Mohseni-Bandpei, Anoushiravan; Khaloo, Shokooh Sadat; Jorfi, Sahand; Saeedi, Reza
2017-07-01
National and sub-national mortality, years of life lost due to premature mortality (YLLs), years lived with disability (YLDs) and disability-adjusted life years (DALYs) for household air pollution from solid cookfuel use (HAP) in Iran, 1990-2013 were estimated based on the Global Burden of Disease Study 2013 (GBD 2013). The burden of disease attributable to HAP was quantified by the comparative risk assessment method using four inputs: (1) exposure to HAP, (2) the theoretical minimum risk exposure level (TMREL), (3) exposure-response relationships of related causes (4) disease burden of related causes. All across the country, solid fuel use decreased from 5.26% in 1990 to 0.15% in 2013. The drastic reduction of solid fuel use leaded to DALYs attributable to HAP fell by 97.8% (95% uncertainty interval 97.7-98.0%) from 87,433 (51072-144303) in 1990 to 1889 (1016-3247) in 2013. Proportion of YLLs in DALYs from HAP decreased from 95.7% in 1990 to 86.6% in 2013. Contribution of causes in the attributable DALYs was variable during the study period and in 2013 was in the following order: ischemic heart disease for 43.4%, chronic obstructive pulmonary disease for 24.7%, hemorrhagic stroke for 9.7%, lower respiratory infections for 9.3%, ischemic stroke for 7.8%, lung cancer for 3.4% and cataract for 1.8%. Based on the Gini coefficient, the spatial inequality of the disease burden from HAP increased during the study period. The remained burden of disease was relatively scarce and it mainly occurred in seven southern provinces. Further reduction of the disease burden from HAP as well as compensation of the increasing spatial inequality in Iran could be attained through an especial plan for providing cleaner fuels in the southern provinces. Copyright © 2017 Elsevier Inc. All rights reserved.
-
Pikelnaya, O.; Polidori, A.; Wimmer, R.; Mellqvist, J.; Samuelsson, J.; Marianne, E.; Andersson, P.; Brohede, S.; Izos, O.
2017-12-01
Industrial facilities such as refineries and oil processing facilities can be sources of chemicals adversely affecting human health, for example aromatic hydrocarbons and formaldehyde. In an urban setting, such as the South Coast Air Basin (SCAB), exposure to harmful air pollutants (HAP's) for residents of communities neighboring such facilities is of serious concern. Traditionally, exposure assessments are performed by modeling a community exposure using emission inventories and data collected at fixed air monitoring sites. However, recent field measurements found that emission inventories may underestimate HAP emissions from refineries; and HAP measurements data from fixed sites is lacking spatial resolution; as a result, the impact of HAP emissions on communities is highly uncertain. The next generation air monitoring technologies can help address these challenges. For example, dense "low-cost" sensors allow continuous monitoring of concentrations of pollutants within communities with high temporal- and spatial- resolution, and optical remote sensing (ORS) technologies offer measurements of emission fluxes and real-time ground-concentration mapping of HAPs. South Coast Air Quality Management District (SCAQMD) is currently conducting a multi-year study using ORS methods and "low-cost" Volatile Organic Compounds (VOCs) sensors to monitor HAP emissions from selected industrial facilities in the SCAB and their ambient concentrations in neighboring communities. For this purpose, quarterly mobile ORS surveys are conducted to quantify facility-wide emissions for VOCs, aromatic hydrocarbons and HCHO, and to collect ground-concentration profiles of these pollutants inside neighboring communities. Additionally, "low-cost" sensor nodes for deployment in neighborhood(s) downwind of the facilities have been developed in order to obtain long-term, granular data on neighborhood VOC concentrations, During this presentation we will discuss initial results of quarterly ORS
-
Korontzi, S.; Ward, D. E.; Susott, R. A.; Yokelson, R. J.; Justice, C. O.; Hobbs, P. V.; Smithwick, E. A. H.; Hao, W. M.
2003-01-01
In this paper we present the first early dry season (early June-early August) emission factor measurements for carbon dioxide (CO2), carbon monoxide (CO), methane (Ca), nonmethane hydrocarbons (NMHC), and particulates with a diameter less than 2.5 microns (pM2.5) for southern African grassland and woodland fires. Seasonal emission factors for grassland fires correlate linearly with the proportion of green grass, used as a surrogate for the fuel moisture content, and are higher for products of incomplete combustion in the early part of the dry season compared with later in the dry season. Models of emission factors for NMHC and PM(sub 2.5) versus modified combustion efficiency (MCE) are statistically different in grassland compared with woodland ecosystems. We compare predictions based on the integration of emissions factors from this study, from the southern African Fire-Atmosphere Research Initiative 1992 (SAFARI-92), and from SAFARI-2000 with those based on the smaller set of ecosystem-specific emission factors to estimate the effects of using regional-average rather than ecosystem-specific emission factors. We also test the validity of using the SAFARI-92 models for emission factors versus MCE to predict the early dry season emission factors measured in this study. The comparison indicates that the largest discrepancies occur at the low end (0.907) and high end (0.972) of MCE values measured in this study. Finally, we combine our models of MCE versus proportion of green grass for grassland fires with emission factors versus MCE for selected oxygenated volatile organic compounds measured in the SAFARI-2000 campaign to derive the first seasonal emission factors for these compounds. The results of this study demonstrate that seasonal variations in savanna fire emissions are important and should be considered in modeling emissions at regional to continental scales.
-
Directory of Open Access Journals (Sweden)
Huiru Zhao
2018-03-01
Full Text Available Carbon dioxide (CO2 emissions forecasting is becoming more important due to increasing climatic problems, which contributes to developing scientific climate policies and making reasonable energy plans. Considering that the influential factors of CO2 emissions are multiplex and the relationships between factors and CO2 emissions are complex and non-linear, a novel CO2 forecasting model called SSA-LSSVM, which utilizes the Salp Swarm Algorithm (SSA to optimize the two parameters of the least squares support sector machine (LSSVM model, is proposed in this paper. The influential factors of CO2 emissions, including the gross domestic product (GDP, population, energy consumption, economic structure, energy structure, urbanization rate, and energy intensity, are regarded as the input variables of the SSA-LSSVM model. The proposed model is verified to show a better forecasting performance compared with the selected models, including the single LSSVM model, the LSSVM model optimized by the particle swarm optimization algorithm (PSO-LSSVM, and the back propagation (BP neural network model, on CO2 emissions in China from 2014 to 2016. The comparative analysis indicates the SSA-LSSVM model is greatly superior and has the potential to improve the accuracy and reliability of CO2 emissions forecasting. CO2 emissions in China from 2017 to 2020 are forecast combined with the 13th Five-Year Plan for social, economic and energy development. The comparison of CO2 emissions of China in 2020 shows that structural factors significantly affect CO2 emission forecasting results. The average annual growth of CO2 emissions slows down significantly due to a series of policies and actions taken by the Chinese government, which means China can keep the promise that greenhouse gas emissions will start to drop after 2030.
-
Corrosion, wettability and thrombogenicity investigation of ion beam modified HAP/Al{sub 2}O{sub 3}
Energy Technology Data Exchange (ETDEWEB)
Shikha, Deep; Shahid, Md.; Jha, Ush [Department of Chemistry, BIT Mesra, Ranchi 835215 (India); Sinha, Sanjay Kumar, E-mail: sksinha@bitmesra.ac.in [Department of Physics, BIT Mesra, Ranchi 835215 (India); Reddy, V. Raghavendra [UGC-DAE Consortium for Scientific Research Indore (India); Ojha, Sunil; Kumar, P.; Kanjilal, Dinakar [IUAC, Aruna Asaf Ali road, New Delhi (India)
2015-08-01
Hydroxyapatite Ca{sub 10}(PO4){sub 6}(OH){sub 2}, is a biosensitive ceramic which promotes bone growth in human fluid. However due to its weak mechanical strength it is often coated on chemically inert material such as alumina. In the present work hydroxyapatite (HAP) of thickness 1 μm is deposited on alumina using sol–gel process and the stoichiometric ratio of Ca:P = 1.67 is maintained. Surface property of HAP is further improved by Ar{sup +} ion implantation. The samples were irradiated with 1.4 MeV Ar{sup +} ions with fluence ranging from 5 × 10{sup 14} to 1 × 10{sup 16} ions/cm{sup 2}. After irradiation, the surface is characterized using Atomic Force Microscope (AFM), Scanning Electron Microscope (SEM), electron dispersive X-ray spectroscopy (EDX), Glancing incidence X-ray diffraction (GXRD) and Rutherford backscattering Spectroscopy (RBS) techniques. Corrosion resistances and impedance analysis were carried out in Ringer solution. RBS and EDX were used to confirm the stoichiometric ratio of the film. Compound formation before and after ion implantation was studied using GXRD. Nanohardness, wettability and thrombogenicity of all the samples were studied. Correlation among surface morphology, improvement in corrosion resistance, hardness, wetability and thrombogenicity before and after ion implantation are discussed in this paper. - Highlights: • .People have worked on HAP coated on metallic alloy and even alumina but the characterization done here are all different. • Throbmobogenicity, corrosion resistance and wetability have all been carried out first time. • Improvement of Surface and interface using energetic inert ions like argon is carried out first time. • The best ion fluence for orthopaedic implants is proposed.
-
On-road assessment of light duty vehicles in Delhi city: Emission factors of CO, CO2 and NOX
Jaiprakash; Habib, Gazala
2018-02-01
This study presents the technology based emission factors of gaseous pollutants (CO, CO2, and NOX) measured during on-road operation of nine passenger cars of diesel, gasoline, and compressed natural gas (CNG). The emissions from two 3-wheelers, and three 2-wheelers were measured by putting the vehicles on jacks and operating them according to Modified Indian Driving Cycle (MIDC) at no load condition. The emission factors observed in the present work were significantly higher than values reported from dynamometer study by Automotive Research Association of India (ARAI). Low CO (0.34 ± 0.08 g km-1) and high NOX (1.0 ± 0.4 g km-1) emission factors were observed for diesel passenger cars, oppositely high CO (2.2 ± 2.6 g km-1) and low NOX (1.0 ± 1.6 g km-1) emission factors were seen for gasoline powered cars. The after-treatment technology in diesel vehicles was effective in CO reduction. While the use of turbocharger in diesel vehicles to generate high combustion temperature and pressure produces more NOx, probably which may not be effectively controlled by after-treatment device. The after-treatment devices in gasoline powered Post-2010, Post-2005 vehicles can be acclaimed for reduced CO emissions compared to Post-2000 vehicles. This work presents a limited data set of emission factors from on-road operations of light duty vehicles, this limitation can be improved by further measurements of emissions from similar vehicles.
-
Urban Household Carbon Emission and Contributing Factors in the Yangtze River Delta, China
Xu, Xibao; Tan, Yan; Chen, Shuang; Yang, Guishan; Su, Weizhong
2015-01-01
Carbon reduction at the household level is an integral part of carbon mitigation. This study analyses the characteristics, effects, contributing factors and policies for urban household carbon emissions in the Yangtze River Delta of China. Primary data was collected through structured questionnaire surveys in three cities in the region – Nanjing, Ningbo, and Changzhou in 2011. The survey data was first used to estimate the magnitude of household carbon emissions in different urban contexts. It then examined how, and to what extent, each set of demographic, economic, behavioral/cognitive and spatial factors influence carbon emissions at the household level. The average of urban household carbon emissions in the region was estimated to be 5.96 tonnes CO2 in 2010. Energy consumption, daily commuting, garbage disposal and long-distance travel accounted for 51.2%, 21.3%, 16.0% and 11.5% of the total emission, respectively. Regulating rapidly growing car-holdings of urban households, stabilizing population growth, and transiting residents’ low-carbon awareness to household behavior in energy saving and other spheres of consumption in the context of rapid population aging and the growing middle income class are suggested as critical measures for carbon mitigation among urban households in the Yangtze River Delta. PMID:25884853
-
Emission factors of black carbon and co-pollutants from diesel vehicles in Mexico City
Zavala, Miguel; Molina, Luisa T.; Yacovitch, Tara I.; Fortner, Edward C.; Roscioli, Joseph R.; Floerchinger, Cody; Herndon, Scott C.; Kolb, Charles E.; Knighton, Walter B.; Paramo, Victor Hugo; Zirath, Sergio; Mejía, José Antonio; Jazcilevich, Aron
2017-12-01
Diesel-powered vehicles are intensively used in urban areas for transporting goods and people but can substantially contribute to high emissions of black carbon (BC), organic carbon (OC), and other gaseous pollutants. Strategies aimed at controlling mobile emissions sources thus have the potential to improve air quality and help mitigate the impacts of air pollutants on climate, ecosystems, and human health. However, in developing countries there are limited data on the BC and OC emission characteristics of diesel-powered vehicles, and thus there are large uncertainties in the estimation of the emission contributions from these sources. We measured BC, OC, and other inorganic components of fine particulate matter (PM), as well as carbon monoxide (CO), nitrogen oxides (NOx), sulfur dioxide (SO2), ethane, acetylene, benzene, toluene, and C2-benzenes under real-world driving conditions for 20 diesel-powered vehicles encompassing multiple emission level technologies in Mexico City with the chasing technique using the Aerodyne mobile laboratory. Average BC emission factors ranged from 0.41-2.48 g kg-1 of fuel depending on vehicle type. The vehicles were also simultaneously measured using the cross-road remote sensing technique to obtain the emission factors of nitrogen oxide (NO), CO, total hydrocarbons, and fine PM, thus allowing for the intercomparison of the results from the two techniques. There is overall good agreement between the two techniques and both can identify high and low emitters, but substantial differences were found in some of the vehicles, probably due to the ability of the chasing technique to capture a larger diversity of driving conditions in comparison to the remote sensing technique. A comparison of the results with the US EPA MOVES2014b model showed that the model underestimates CO, OC, and selected VOC species, whereas there is better agreement for NOx and BC. Larger OC / BC ratios were found in comparison to ratios measured in California using
-
Emission factors of black carbon and co-pollutants from diesel vehicles in Mexico City
Directory of Open Access Journals (Sweden)
M. Zavala
2017-12-01
Full Text Available Diesel-powered vehicles are intensively used in urban areas for transporting goods and people but can substantially contribute to high emissions of black carbon (BC, organic carbon (OC, and other gaseous pollutants. Strategies aimed at controlling mobile emissions sources thus have the potential to improve air quality and help mitigate the impacts of air pollutants on climate, ecosystems, and human health. However, in developing countries there are limited data on the BC and OC emission characteristics of diesel-powered vehicles, and thus there are large uncertainties in the estimation of the emission contributions from these sources. We measured BC, OC, and other inorganic components of fine particulate matter (PM, as well as carbon monoxide (CO, nitrogen oxides (NOx, sulfur dioxide (SO2, ethane, acetylene, benzene, toluene, and C2-benzenes under real-world driving conditions for 20 diesel-powered vehicles encompassing multiple emission level technologies in Mexico City with the chasing technique using the Aerodyne mobile laboratory. Average BC emission factors ranged from 0.41–2.48 g kg−1 of fuel depending on vehicle type. The vehicles were also simultaneously measured using the cross-road remote sensing technique to obtain the emission factors of nitrogen oxide (NO, CO, total hydrocarbons, and fine PM, thus allowing for the intercomparison of the results from the two techniques. There is overall good agreement between the two techniques and both can identify high and low emitters, but substantial differences were found in some of the vehicles, probably due to the ability of the chasing technique to capture a larger diversity of driving conditions in comparison to the remote sensing technique. A comparison of the results with the US EPA MOVES2014b model showed that the model underestimates CO, OC, and selected VOC species, whereas there is better agreement for NOx and BC. Larger OC / BC ratios were found in comparison to ratios
-
Abinaya Sindu, P; Kolanthai, Elayaraja; Suganthi, R V; Thanigai Arul, K; Manikandan, E; Catalani, Luiz H; Narayana Kalkura, S
2017-10-01
The aim of the current study is to synthesize nanosized silicon incorporated HAp (Si-HAP) using sodium metasilicate as the silicon source. The sol-gel derived samples were further subjected to microwave irradiation. Incorporation of Si into HAp did not alter the HAp phase, as confirmed by the X-ray diffraction analysis (XRD). Moreover, variation in the lattice parameters of the Si-incorporated HAp indicates that Si is substituted into the HAp lattice. The decrease in the intensity of the peaks attributed to hydroxyl groups, which appeared in the FTIR and Raman spectra of Si-HAp, further confirms the Si substitution in HAp lattices. The silicon incorporation enhanced the nanorods length by 70%, when compared to that of pure HAp. Microwave irradiation improved the crystallinity of Si-HAp when compared to as-synthesized Si-HAp samples. As-synthesized Si-incorporated HAp sample showed an intense blue emission under UV excitation. Microwave irradiation reduced the intensity of blue emission and exhibited red shift due to the reduction of defects in the Si-HAp crystal. The morphological change from rod to spherical and ribbon-like forms was observed with an increase in silicon content. Further, Si-HAp exhibited better bioactivity and low dissolution rate. Initially there was a burst release of amoxicillin from all the samples, subsequently it followed a sustained release. The microwave-irradiated HAp showed extended period of sustained release than that of as-synthesized HAp and Si-HAp. Similarly, the microwave-irradiated Si-incorporated samples exhibited prolonged drug release, as compared to that of the as-synthesized samples. Hence, Si-HAp is rapidly synthesized by a simple and cost effective method without inducing any additional phases, as compared to the conventional sintering process. This study provides a new insight into the rapid green synthesis of Si-HAp. Si-HAp could emerge as a promising material for the bone tissue replacement and as a drug delivery system
-
Directory of Open Access Journals (Sweden)
Seong-Beom Ahn
2014-06-01
Full Text Available Cytokines, chemokines and growth factors (CCGFs in human plasma are analyzed for identification of biomarkers. However concentrations of CCGFs are very low; it is difficult to identify and quantify low abundance proteins in the presence of the high abundance proteins (HAPs unless HAPs are removed prior to analysis. However, there is a concern that the low abundance proteins such as CCGFs may also be removed during the HAP depletion process. In this study, we have examined whether or not depletion of the HAPs enhances detection of the CCGFs by immuno-assays. Top 14 HAPs were depleted from 10 healthy volunteers’ plasma using MARS-14 immuno-depletion column and a total of 27 CCGFs were analyzed by bead-based multiplexed immuno-assay. All 27 CCGFs were detected in neat plasma (NP, 25 were detected in flow through fraction (FT and 21 were detected in bound protein (BP fraction. Concentrations of 22 CCGFs were significantly higher in NP compared to FT and BP. Only one CCGF had higher concentration in FT compared to NP. The remaining 2 CCGFs were not different between NP and FT. It was counter-productive for the detection of 24 CCGFs after HAP removal, primarily due to post-depletion protein precipitation and/or re-suspension of pellets.
-
Energy Technology Data Exchange (ETDEWEB)
Bellerby, John M.; Blackman, Christopher S. [Department of Environmental and Ordnance Systems, Cranfield University, Defence College of Management and Technology, Shrivenham, Swindon SN6 8LA (United Kingdom)
2007-06-15
Gas chromatography (GC) with a Flame Ionisation Detector (FID) has been used to determine changes in the concentrations of the components of Otto Fuel II (OF) in contact with an 82% aqueous solution of hydroxylammonium perchlorate (HAP) in sealed vials at 31.7 C during the period leading up to auto-ignition of the two liquids. The concentration of hydroxylamine in HAP was monitored over the same period using a titration method. It was found that 2-nitrodiphenylamine (2NDPA), the stabiliser in the OF, is completely consumed after about 65-70 h and that the concentration of hydroxylamine begins to fall at this point. 1,2-Propanediol dinitrate (propylene glycol dinitrate, PGDN), the energetic component in the OF, is not depleted significantly until after about 90 h. The evolution of nitrous oxide (N{sub 2}O) between 65 and 90 h is attributed to the reaction of the hydroxylammonium ion with nitrous acids produced by PGDN decomposition at the liquid-liquid interface. Carbon dioxide (CO{sub 2}) is evolved after 90 h and is attributed to PGDN decomposition. HAP and PGDN are each thought to contribute to N{sub 2}O evolution after 90 h. (Abstract Copyright [2007], Wiley Periodicals, Inc.)
-
40 CFR 264.1034 - Test methods and procedures.
2010-07-01
... calibration gas must be the single organic HAP representing the largest percent by volume of the emissions... factor for molar volume, kg-mol/m3 (@ 293 K and 760 mm Hg); 10− 6 = Conversion from ppm (B) For sources...; 0.0416 = Conversion factor for molar volume, kg-mol/m3 (@ 293 K and 760 mm Hg); 10− 6 = Conversion...
-
Regulation of the yeast metabolic cycle by transcription factors with periodic activities
Directory of Open Access Journals (Sweden)
Pellegrini Matteo
2011-10-01
Full Text Available Abstract Background When growing budding yeast under continuous, nutrient-limited conditions, over half of yeast genes exhibit periodic expression patterns. Periodicity can also be observed in respiration, in the timing of cell division, as well as in various metabolite levels. Knowing the transcription factors involved in the yeast metabolic cycle is helpful for determining the cascade of regulatory events that cause these patterns. Results Transcription factor activities were estimated by linear regression using time series and genome-wide transcription factor binding data. Time-translation matrices were estimated using least squares and were used to model the interactions between the most significant transcription factors. The top transcription factors have functions involving respiration, cell cycle events, amino acid metabolism and glycolysis. Key regulators of transitions between phases of the yeast metabolic cycle appear to be Hap1, Hap4, Gcn4, Msn4, Swi6 and Adr1. Conclusions Analysis of the phases at which transcription factor activities peak supports previous findings suggesting that the various cellular functions occur during specific phases of the yeast metabolic cycle.
-
International Nuclear Information System (INIS)
Cai, H.; Wang, M.; Elgowainy, A.; Han, J.
2012-01-01
Greenhouse gas (CO 2 , CH 4 and N 2 O, hereinafter GHG) and criteria air pollutant (CO, NO x , VOC, PM 10 , PM 2.5 and SO x , hereinafter CAP) emission factors for various types of power plants burning various fuels with different technologies are important upstream parameters for estimating life-cycle emissions associated with alternative vehicle/fuel systems in the transportation sector, especially electric vehicles. The emission factors are typically expressed in grams of GHG or CAP per kWh of electricity generated by a specific power generation technology. This document describes our approach for updating and expanding GHG and CAP emission factors in the GREET (Greenhouse Gases, Regulated Emissions, and Energy Use in Transportation) model developed at Argonne National Laboratory (see Wang 1999 and the GREET website at http://greet.es.anl.gov/main) for various power generation technologies. These GHG and CAP emissions are used to estimate the impact of electricity use by stationary and transportation applications on their fuel-cycle emissions. The electricity generation mixes and the fuel shares attributable to various combustion technologies at the national, regional and state levels are also updated in this document. The energy conversion efficiencies of electric generating units (EGUs) by fuel type and combustion technology are calculated on the basis of the lower heating values of each fuel, to be consistent with the basis used in GREET for transportation fuels. On the basis of the updated GHG and CAP emission factors and energy efficiencies of EGUs, the probability distribution functions (PDFs), which are functions that describe the relative likelihood for the emission factors and energy efficiencies as random variables to take on a given value by the integral of their own probability distributions, are updated using best-fit statistical curves to characterize the uncertainties associated with GHG and CAP emissions in life-cycle modeling with GREET.
-
International Nuclear Information System (INIS)
Davarpanah, M. R.; Khoshhosn, H. A.; Attar Nosrati, S.; Harati, S. M.; Aghamiri, S. M.; Ghannadi Maragheh, M.
2012-01-01
Radio synovectomy is a local intra-articular injection of radionuclides in colloidal form for treatment of articular inflammatory in rheumatoid arthritis, hemophilia or orthopedic troubles. β-emitting radionuclides can be used for various joints based on radiation energy. 90 Y is a pure β-emitter with a half-life of 64.1 hours that is used for treatment of the knee joint. β-radiation of this radionuclide possesses maximum energy of 2.281 MeV (99.98%), mean pathway of 3.6 mm in the soft tissue and maximum 11 mm. In this project, hydroxyapatite (HAp) is applied as a colloid maker agent that interacts with 90 Y 3+ ions via ion-dipole bonds and produces 90 Y-HAp. The colloidal pharmaceutical is produced by adding an acidic solution of 90 YCl 3 to an HAp suspension in saline. Effective parameters within which the colloid is applied, such as the volume of diluent, HAp particle size and sonication effect were evaluated and tested. First, these determinative parameters were optimized in the simulated conditions and then examined in the active phase. Finally, the best procedure was determined for the production of the radiopharmaceutical. Radionuclide purity of the radiopharmaceutical according to the primary 90 YCl 3 solution was over 99.9%. Labeling yield and radiochemical purity were obtained over 99% using TLC method in saline solvent up to three days after production of radiopharmaceutical. Radiochemical purity of 90 Y-HAp colloid was also evaluated in human serum albumin solution for three days at room temperature. The amount of released activity was between 0.3 to 2%.
-
Determination of OB/OD/SF Emission Factors Using Unmanned Aerial Systems
A presentation to the Demilitarization Symposium. This proposal will present the methods of tethered aerostat and unmanned aerial system for collection of plume samples and determination of emission factors form open burning, open detonation, and static firing for weapon demilita...
-
National Research Council Canada - National Science Library
Kelley, John; Considine, Thomas
2006-01-01
...). The purpose of this effort is to investigate HAP-free alternative chemical paint strippers as potential replacements for the methylene-chloride- based chemical strippers currently used in both processes...
-
DEFF Research Database (Denmark)
de Vries, Paul S; Sabater-Lleal, Maria; Chasman, Daniel I
2017-01-01
An increasing number of genome-wide association (GWA) studies are now using the higher resolution 1000 Genomes Project reference panel (1000G) for imputation, with the expectation that 1000G imputation will lead to the discovery of additional associated loci when compared to HapMap imputation. In...
-
2010-07-01
... a HAP, excluding bag dumps where the feedstock contains HAP only as impurities. (3) Gaseous HAP... process vent emissions in paragraph (b) of this section. (f) Heat exchange systems. Unless one or more of... operator shall monitor each heat exchange system that is used to cool process equipment in PAI process...
-
Directory of Open Access Journals (Sweden)
Mei-Hung Chi
2011-07-01
Full Text Available The genetic influence of single nucleotide polymorphisms (SNPs on antidepressant efficacy has been previously demonstrated. To evaluate whether there are ethnic differences, we compared the allele frequencies of antidepressant efficacy-related SNPs between the Taiwanese population and four other populations in the HapMap database. We recruited 198 Taiwanese major depression patients and 106 Taiwanese controls. A panel of possible relevant SNPs (in brain-derived neurotrophic factor, 5-hydroxytryptamine receptor 2A, interleukin 1 beta, and G-protein beta 3 subunit genes was selected for comparisons of allele frequencies using the χ2 test. Our results suggested no difference between Taiwanese patients and controls, but there were significant differences among Taiwanese controls and the other four ethnic groups in brain-derived neurotrophic factor, 5-hydroxytryptamine receptor 2A, interleukin 1 beta and G-protein beta 3 subunit genes. We conclude that there are ethnic differences in the allele frequencies of antidepressant efficacy-related SNPs, and that the degree of variations is consistent with geographic distances. Further investigation is required to verify the attribution of genetic differences to ethnic-specific antidepressant responses.
-
Research on carbon emission driving factors of China’s provincial construction industry
Shang, Mei; Dong, Rui; Fu, Yujie; Hao, Wentao
2018-03-01
As a pillar industry of the national economy, the damage to the environment by construction industry can not be ignored. In the context of low carbon development, identifying the main driving factors for the carbon emission of the provincial construction industry are the key for the local government to formulate the development strategy for construction. In the paper, based on the Kaya factor decomposition method, the carbon intensity of the energy structure, energy intensity and the impact of the construction output on the carbon emission of provincial construction industry are studied, and relevant suggestions for low carbon development of provincial construction industry are proposed. The conclusion of this paper provides a theoretical basis for the early realization of low-carbon development in China’s provincial construction industry.
-
Xue, Yifeng; Zhou, Zhen; Nie, Teng; Wang, Kun; Nie, Lei; Pan, Tao; Wu, Xiaoqing; Tian, Hezhong; Zhong, Lianhong; Li, Jing; Liu, Huanjia; Liu, Shuhan; Shao, Panyang
2016-10-01
Residential coal combustion is considered to be an important source of air pollution in Beijing. However, knowledge regarding the emission characteristics of residential coal combustion and the related impacts on the air quality is very limited. In this study, we have developed an emission inventory for multiple hazardous air pollutants (HAPs) associated with residential coal combustion in Beijing for the period of 2000-2012. Furthermore, a widely used regional air quality model, the Community Multi-Scale Air Quality model (CMAQ), is applied to analyze the impact of residential coal combustion on the air quality in Beijing in 2012. The results show that the emissions of primary air pollutants from residential coal combustion have basically remained the same levels during the past decade, however, along with the strict emission control imposed on major industrial sources, the contribution of residential coal combustion emissions to the overall emissions from anthropogenic sources have increased obviously. In particular, the contributions of residential coal combustion to the total air pollutants concentrations of PM10, SO2, NOX, and CO represent approximately 11.6%, 27.5%, 2.8% and 7.3%, respectively, during the winter heating season. In terms of impact on the spatial variation patterns, the distributions of the pollutants concentrations are similar to the distribution of the associated primary HAPs emissions, which are highly concentrated in the rural-urban fringe zones and rural suburb areas. In addition, emissions of primary pollutants from residential coal combustion are forecasted by using a scenario analysis. Generally, comprehensive measures must be taken to control residential coal combustion in Beijing. The best way to reduce the associated emissions from residential coal combustion is to use economic incentive means to promote the conversion to clean energy sources for residential heating and cooking. In areas with reliable energy supplies, the coal used
-
International inequalities in per capita CO2 emissions: a decomposition methodology by Kaya factors
International Nuclear Information System (INIS)
Duro, J.A.; Universitat de Barcelona; Padilla, E.
2006-01-01
In this paper, we provide a methodology for decomposing international inequalities in per capita CO 2 emissions into Kaya (multiplicative) factors and two interaction terms. We use the Theil index of inequality and show that this decomposition methodology can be extended for analyzing between- and within-group inequality components. We can thus analyze the factors behind inequalities in per capita CO 2 emissions across countries, between groups of countries and within groups of countries. The empirical illustration for international data suggests some points. Firstly, international inequality in per capita CO 2 emissions is mainly attributable to inequalities in per capita income levels, which helps to explain its recent reduction, while differences in carbon intensity of energy and energy intensity have made a less significant contribution. This result is strongly influenced by the performance of China and India. Secondly, the between-group inequality component, which is the biggest component, is also largely explained by the income factor. Thirdly, the within-group inequality component increased slightly during the period, something mainly due to the change in the income factor and the interaction terms in a few regions. (author)
-
Consideration of Real World Factors Influencing Greenhouse Gas Emissions in ALPHA
Discuss a variety of factors that influence the simulated fuel economy and GHG emissions that are often overlooked and updates made to ALPHA based on actual benchmarking data observed across a range of vehicles and transmissions. ALPHA model calibration is also examined, focusin...
-
Analyzing impact factors of CO2 emissions using the STIRPAT model
International Nuclear Information System (INIS)
Fan Ying; Liu Lancui; Wu Gang; Wei Yiming
2006-01-01
Using the STIRPAT model, this paper analyzes the impact of population, affluence and technology on the total CO 2 emissions of countries at different income levels over the period 1975-2000. Our main results show at the global level that economic growth has the greatest impact on CO 2 emissions, and the proportion of the population between ages 15 and 64 has the least impact. The proportion of the population between 15 and 64 has a negative impact on the total CO 2 emissions of countries at the high income level, but the impact is positive at other income levels. This may illustrate the importance of the 'B' in the 'I = PABT'; that is to say that different behavior fashions can greatly influence environmental change. For low-income countries, the impact of GDP per capita on total CO 2 emissions is very great, and the impact of energy intensity in upper-middle income countries is very great. The impact of these factors on the total CO 2 emissions of countries at the high income level is relatively great. Therefore, these empirical results indicate that the impact of population, affluence and technology on CO 2 emissions varies at different levels of development. Thus, policy-makers should consider these matters fully when they construct their long-term strategies for CO 2 abatement
-
International Nuclear Information System (INIS)
Wang, Zhaohua; Yin, Fangchao; Zhang, Yixiang; Zhang, Xian
2012-01-01
Highlights: ► We adapt STIRPAT model to regional context and conduct PLS regress analysis. ► Energy technology related patent is innovatively used to measure technical factors. ► Urbanization level has the greatest interpretative ability for CO 2 emissions. ► We do not find evidence of Environmental Kuznets Curve in Beijing. ► Beijing should focus more on tertiary industry and residential energy consumption. -- Abstract: In order to further study the realization of carbon intensity target, find the key influencing factors of CO 2 emissions, and explore the path of developing low-carbon economy, this paper empirically studied the influences of urbanization level, economic level, industry proportion, tertiary industry proportion, energy intensity and R and D output on CO 2 emissions in Beijing using improved STIRPAT (stochastic impacts by regression on population, affluence and technology) model. The model is examined using partial least square regression. Results show that urbanization level, economic level and industry proportion positively influence the CO 2 emissions, while tertiary industry proportion, energy intensity and R and D output negatively do. Urbanization level is the main driving factor of CO 2 emissions, and tertiary industry proportion is the main inhibiting factor. In addition, along with the growth of per capita GDP, the increase of CO 2 emissions does not follow the Environmental Kuznets Curve model. Based on these empirical findings and the specific circumstances of Beijing, we provide some policy recommendations on how to reduce carbon intensity. Beijing should pay more attention to tertiary industry and residential energy consumption for carbon emission reduction. It is necessary to establish a comprehensive evaluation index of social development. Investing more capital on carbon emission reduction science and technology, and promoting R and D output is also an efficient way to reduce CO 2 emissions.
-
Lesschen, J.P.; Velthof, G.L.
2009-01-01
Nitrous oxide (N2O) contributes 8% to anthropogenic global warming, of which about one third are direct emissions of agricultural soils. These N2O emissions are often estimated using the default IPCC 2006 emission factor of 1% of the amount of N applied for mineral fertilizer, manure and crop
-
Energy Technology Data Exchange (ETDEWEB)
Schwarz, Winfried [Oeko-Recherche, Buero fuer Umweltforschung und -beratung GmbH, Frankfurt am Main (Germany)
2005-06-15
Before the 1997 Kyoto Protocol on Climate Protection, the fluorinated greenhouse gases HFCs, PFCs, and SF6 (F-gases) aroused little public attention. Since then, the standards on surveying and reporting on national emissions have been rising constantly. Amongst others, the annual reporting to the UNFCCC secretariat makes detailed declarations on use and emissions of F-gases necessary, which have to be filled in specified formats for submission (Common Reporting Format = CRF). The scientific basis has been set out by the UNFCCC guidelines on reporting, in accordance with the instructions laid down in IPCC good practice guidance. Additionally, in Germany the Centralised System of Emissions (ZSE) shall provide a suitable tool to satisfy any quality needs of both activity data and emission factors. From 1995 onwards, activity data and emissions of each individual application sector shall be presented in a comprehensible and transparent way. Therefore, the way of data collection as well as the estimation methods applied must be well documented. Moreover, data has to be prepared for appropriate importation into ZSE. It is the objective of this study to provide the transparency demanded within 40 national application sectors of F-gases, for the period between 1995 and 2002. - Firstly, all the activity data as well as the emissions related to them are presented and commented. This applies to manufacturing of products, F-gases banked in operating systems, and decommissioning. - Secondly, the methodologies applied to calculate the emissions are described and all sources of information are revealed, e.g. literature, names of experts from the manufacturing industry, users, trade, and academia. - Thirdly, reliability and safety of data are discussed. - Fourthly, possible deviations from the IPCC default values are stated and given reasons for. Wherever this intensive reviewing of 40 sectors through eight years of reporting uncovers gaps or inconsistencies in previous reports
-
2012-01-30
... During Periods of Startup, Shutdown and Malfunctions (SSM) VI. Requirements for Metal HAP Process Vents A. Definition of Metal HAP Process Vent B. Metal HAP Process Vent Standards VII. Technical Corrections and...: Chromium Compounds, Polyvinyl Chloride and Copolymers Production, Paint and Allied Coatings and Mercury...
-
Directory of Open Access Journals (Sweden)
Yidan Chen
2018-02-01
Full Text Available China built pilot carbon emission trading schemes in seven regions and established a national carbon trading market in electricity sector in December 2017. This study conducted a questionnaire survey of 570 companies in 29 regions nationwide and found that companies still need to improve mitigation measures regarding fossil fuel combustion, production technology, output adjustment and environmental management. By establishing regression models, influencing factors of carbon emission reduction are identified. Pilot emission trading policy has a significant impact on company emission reduction behaviors. Companies inside or outside the pilot region respond differently to the influencing factors. Companies inside emphasize more on energy price and mitigation potential, while enterprises outside pay more attention to investment and familiarity with technology and policy.
-
Comprehensive assessment of toxic emissions from coal-fired power plants
International Nuclear Information System (INIS)
Brown, T.D.; Schmidt, C.E.; Radziwon, A.S.
1991-01-01
The Pittsburgh Energy Technology Center (PETC) of the US Department of Energy (DOE) has two current investigations, initiated before passage of the Clean Air Act Amendment (CAAA), that will determine the air toxic emissions from coal-fired electric utilities. DOE has contracted with Battelle Memorial Institute and Radian corporation to conduct studies focusing on the potential air toxics, both organic and inorganic, associated with different size fractions of fine particulate matter emitted from power plant stacks. Table 2 indicates the selected analytes to be investigated during these studies. PETC is also developing guidance on the monitoring of Hazardous Air Pollutants (HAPS) to be incorporated in the Environmental Monitoring plans for the demonstration projects in its Clean Coal Technology Program
-
A Factor Decomposition on China’s Carbon Emission from 1997 to 2012 Based on IPAT-LMDI Model
Directory of Open Access Journals (Sweden)
Wei Li
2015-01-01
Full Text Available We probe into the key factors that possess significant effects on China’s CO2 emissions during 1997–2012 on the basis of IPAT-LMDI model. Carbon dioxide emissions are specifically decomposed into CO2 emission intensity, energy structure, energy intensity, industrial structure, economic output, and population scale effects. Results indicate that the paramount driving factors that resulted in the growth of CO2 emissions are economic output, population scale, and energy structure. In contrast, energy intensity and industrial structure generally play an outstanding role in reducing emissions. This paper constructs a new weight assessment system by introducing “contribution value-significant factor-effect coefficient” to replace “contribution value-contribution rate” in the previous literature. According to the most significant positive effect and the most negative effect from the conclusion, we point out the effective policies that can not only accelerate the target of “China’s carbon emissions per unit of GDP could be cut down by 40–45% by 2020, from 2005 levels,” but also have crucial significance on the low-carbon economic development strategy of China.
-
Huang, Cheng; Tao, Shikang; Lou, Shengrong; Hu, Qingyao; Wang, Hongli; Wang, Qian; Li, Li; Wang, Hongyu; Liu, Jian'gang; Quan, Yifeng; Zhou, Lanlan
2017-11-01
CO, THC, NOx, and PM emission factors of 51 light-duty gasoline vehicles (LDGVs) spanning the emission standards from Euro 2 to Euro 5 were measured by a chassis dynamometer. High frequencies of high-emitting vehicles were observed in Euro 2 and Euro 3 LDGV fleet. 56% and 33% of high-emitting vehicles contributed 81%-92% and 82%-85% of the emissions in Euro 2 and Euro 3 test fleet, respectively. Malfunctions of catalytic convertors after high strength use are the main cause of the high emissions. Continuous monitoring of a gasoline vehicle dominated tunnel in Shanghai, China was conducted to evaluate the average emission factors of vehicles in real-world. The results indicated that the emission factors of LDGVs were considerably underestimated in EI guidebook in China. The overlook of high-emitting vehicles in older vehicle fleet is the main reason for this underestimation. Enhancing the supervision of high emission vehicles and strengthening the compliance tests of in-use vehicles are essential measures to control the emissions of in-use gasoline vehicles at the present stage in China.
-
Emission Factors of Selected Organic Compounds from Domestic Hardwood Combustion
Czech Academy of Sciences Publication Activity Database
Hopan, F.; Šyc, Michal; Horák, J.; Dej, M.; Krpec, K.; Ocelka, T.; Tomšej, T.; Pekárek, Vladimír
LVI, č. 3 (2009), s. 81-85 ISSN 1210-0471 R&D Projects: GA MŽP(CZ) SP/1A2/116/07; GA MŠk 2B08048 Institutional research plan: CEZ:AV0Z40720504 Keywords : wood * small sources * emission factors Subject RIV: DI - Air Pollution ; Quality http://transactions.fs.vsb.cz/2009-3/12hop.pdf
-
Energy Technology Data Exchange (ETDEWEB)
Friedrich, Elena, E-mail: Friedriche@ukzn.ac.za [CRECHE Centre for Research in Environmental, Coastal and Hydrological Engineering, School of Engineering, Civil Engineering Programme, University of KwaZulu-Natal, Howard College Campus, Durban (South Africa); Trois, Cristina [CRECHE Centre for Research in Environmental, Coastal and Hydrological Engineering, School of Engineering, Civil Engineering Programme, University of KwaZulu-Natal, Howard College Campus, Durban (South Africa)
2013-04-15
Highlights: ► An average GHG emission factor for the collection and transport of municipal solid waste in South Africa is calculated. ► A range of GHG emission factors for different types of landfills (including dumps) in South Africa are calculated. ► These factors are compared internationally and their implications for South Africa and developing countries are discussed . ► Areas for new research are highlighted. - Abstract: Greenhouse gas (GHG) emission factors are used with increased frequency for the accounting and reporting of GHG from waste management. However, these factors have been calculated for developed countries of the Northern Hemisphere and are lacking for developing countries. This paper shows how such factors have been developed for the collection, transport and landfilling of municipal waste in South Africa. As such it presents a model on how international results and methodology can be adapted and used to calculate country-specific GHG emission factors from waste. For the collection and transport of municipal waste in South Africa, the average diesel consumption is around 5 dm{sup 3} (litres) per tonne of wet waste and the associated GHG emissions are about 15 kg CO{sub 2} equivalents (CO{sub 2} e). Depending on the type of landfill, the GHG emissions from the landfilling of waste have been calculated to range from −145 to 1016 kg CO{sub 2} e per tonne of wet waste, when taking into account carbon storage, and from 441 to 2532 kg CO{sub 2} e per tonne of wet waste, when carbon storage is left out. The highest emission factor per unit of wet waste is for landfill sites without landfill gas collection and these are the dominant waste disposal facilities in South Africa. However, cash strapped municipalities in Africa and the developing world will not be able to significantly upgrade these sites and reduce their GHG burdens if there is no equivalent replacement of the Clean Development Mechanism (CDM) resulting from the Kyoto agreement
-
2010-07-01
... Reconstructed 2SLB and Compression Ignition Stationary RICE >500 HP Located at a Major Source of HAP Emissions, Existing Non-Emergency Compression Ignition Stationary RICE >500 HP, and New and Reconstructed 4SLB Burn Stationary RICE â¥250 HP Located at a Major Source of HAP Emissions 2b Table 2b to Subpart ZZZZ of Part 63...
-
Detección de metabolitos de biodegradación de HAPS en suelos contaminados.
Calero Cáceres, William Ricardo
2012-01-01
Los Hidrocarburos Aromáticos Policíclicos (HAPs) son un grupo de contaminantes orgánicos persistentes comúnmente encontrados en emplazamientos industriales. En muchos casos, estos compuestos provienen de la creosota utilizada como presevante de la madera. Debido a su toxicidad y persistencia ambiental, en 1979 la Agencia de Protección Ambiental de Estados Unidos US EPA incluyó 16 de estos compuestos en la lista de contaminantes prioritarios (Keith & Telliard, 1976)...
-
Energy Technology Data Exchange (ETDEWEB)
Cai, H.; Wang, M.; Elgowainy, A.; Han, J. (Energy Systems)
2012-07-06
Greenhouse gas (CO{sub 2}, CH{sub 4} and N{sub 2}O, hereinafter GHG) and criteria air pollutant (CO, NO{sub x}, VOC, PM{sub 10}, PM{sub 2.5} and SO{sub x}, hereinafter CAP) emission factors for various types of power plants burning various fuels with different technologies are important upstream parameters for estimating life-cycle emissions associated with alternative vehicle/fuel systems in the transportation sector, especially electric vehicles. The emission factors are typically expressed in grams of GHG or CAP per kWh of electricity generated by a specific power generation technology. This document describes our approach for updating and expanding GHG and CAP emission factors in the GREET (Greenhouse Gases, Regulated Emissions, and Energy Use in Transportation) model developed at Argonne National Laboratory (see Wang 1999 and the GREET website at http://greet.es.anl.gov/main) for various power generation technologies. These GHG and CAP emissions are used to estimate the impact of electricity use by stationary and transportation applications on their fuel-cycle emissions. The electricity generation mixes and the fuel shares attributable to various combustion technologies at the national, regional and state levels are also updated in this document. The energy conversion efficiencies of electric generating units (EGUs) by fuel type and combustion technology are calculated on the basis of the lower heating values of each fuel, to be consistent with the basis used in GREET for transportation fuels. On the basis of the updated GHG and CAP emission factors and energy efficiencies of EGUs, the probability distribution functions (PDFs), which are functions that describe the relative likelihood for the emission factors and energy efficiencies as random variables to take on a given value by the integral of their own probability distributions, are updated using best-fit statistical curves to characterize the uncertainties associated with GHG and CAP emissions in life
-
Analysis of Grid Emission Factors for the Electricity Sector in Caribbean Countries
DEFF Research Database (Denmark)
Hinostroza, Miriam L.; Desgain, Denis DR; Perez Martín, David
by undertaking a study to calculate standardized grid emissionfactors (GEF) for sixteen independent nations or groups of countries in the Caribbean region as a basis to the further identification of mitigation activities such as CDM PoAs or any other market-related instrument to be approved by the UNFCCC......As part of their capacity development efforts to promote mitigation actions, the UNEP DTU Partnership, together with the UNFCCC Regional Collaborating Centre in the Caribbean, UNDP and OLADE, agreed to collaborate with Caribbean countries willing to update or establish their grid emission factors...... emission factor for countries with generation units with similar characteristics. Data on the power systems of the different countries have been collected from several centres and institutions, including the UNEP DTU Partnership, the Latin American Energy Organization (OLADE), the Caribbean Community...
-
International Nuclear Information System (INIS)
Lawrence, Samantha; Sokhi, Ranjeet; Ravindra, Khaiwal
2016-01-01
Road tunnels act like large laboratories; they provide an excellent environment to quantify atmospheric particles emission factors from exhaust and non-exhaust sources due to their known boundary conditions. Current work compares the High Volume, Dichotomous Stacked Filter Unit and Partisol Air Sampler for coarse, PM_1_0 and PM_2_._5 particle concentration measurement and found that they do not differ significantly (p = 95%). PM_2_._5 fraction contributes 66% of PM_1_0 proportions and significantly influenced by traffic (turbulence) and meteorological conditions. Mass emission factors for PM_1_0 varies from 21.3 ± 1.9 to 28.8 ± 3.4 mg/vkm and composed of Motorcycle (0.0003–0.001 mg/vkm), Cars (26.1–33.4 mg/vkm), LDVs (2.4–3.0 mg/vkm), HDVs (2.2–2.8 mg/vkm) and Buses (0.1 mg/vkm). Based on Lawrence et al. (2013), source apportionment modelling, the PM_1_0 emission of brake wear (3.8–4.4 mg/vkm), petrol exhaust (3.9–4.5 mg/vkm), diesel exhaust (7.2–8.3 mg/vkm), re-suspension (9–10.4 mg/vkm), road surface wear (3.9–4.5 mg/vkm), and unexplained (7.2 mg/vkm) were also calculated. The current study determined that the combined non-exhaust fleet PM_1_0 emission factor (16.7–19.3 mg/vkm) are higher than the combined exhaust emission factor (11.1–12.8 mg/vkm). Thus, highlight the significance of non-exhaust emissions and the need for legislation and abatement strategies to reduce their contributions to ambient PM concentrations. - Highlights: • Calculations of exhaust/non-exhaust particulate emission factors using tunnel sampling and source apportionment techniques. • Non-exhaust emission dominates in the fine particle fraction, considered responsible for adverse human health impacts. • Emission factors for non-exhaust sources (e.g. tyre and brake) were calculated. • Fleet source PM_1_0 emission factor were also calculated, which can be used in dispersion modelling and health risk assessment. • Tukey mean
-
Kus, Melike; Akan, Perihan; Aydinalp Koksal, Merih; Gullu, Gulen
2017-11-01
Energy demand of Turkey has been showing a remarkable increase in the last two decades due to rapid increase in population and changes in consumption trends. In parallel to the increase in energy demand, the CO2 emissions in Turkey are also increasing dramatically due to high usage of fossil fuels. CO2 emissions from the residential sector covers almost one fourth of the total sectoral emissions. In this study, CO2 emissions from the residential sector are estimated, and the factors affecting the emission levels are determined for the residential sector in Ankara, Turkey. In this study, detailed surveys are conducted to more than 400 households in Ankara. Using the information gathered from the surveys, the CO2 emissions associated with energy consumption of the households are calculated using the methodology outlined at IPCC. The statistical analyses are carried out using household income, dwelling characteristics, and household economic and demographic data to determine the factors causing the variation in emission levels among the households. The results of the study present that the main factors impacting the amount of total energy consumption and associated CO2 emissions are household income, dwelling construction year, age, education level of the household, and net footage of the dwelling.
-
2010-07-01
... Rubber. EPI = Epichlorohydrin Rubber. EPR = Ethylene Propylene Rubber. HBR = Halobutyl Rubber. HYP = Hypalon TM. NEO = Neoprene. NBL = Nitrile Butadiene Latex. NBR = Nitrile Butadiene Rubber. PBR/SBRS... products] Organic HAP/chemical name (CAS No.) Elastomer product/subcategory BR EPI EPR HBR HYP NEO NBL NBR...
-
DeCarlo, P. F.; Goetz, J. D.; Giordano, M.; Stockwell, C.; Maharjan, R.; Adhikari, S.; Bhave, P.; Praveen, P. S.; Panday, A. K.; Jayarathne, T. S.; Stone, E. A.; Yokelson, R. J.
2017-12-01
Characterization of aerosol emissions from prevalent but under sampled combustion sources in South Asia was performed as part of the Nepal Ambient Monitoring and Source Testing Experiment (NAMaSTE) in April 2015. Targeted emission sources included cooking stoves with a variety of solid fuels, brick kilns, garbage burning, crop-residue burning, diesel irrigation pumps, and motorcycles. Real-time measurements of submicron non-refractory particulate mass concentration and composition were obtained using an Aerodyne mini Aerosol Mass Spectrometer (mAMS). Speciated PM1 mass emission factors were calculated for all particulate species (e.g. organics, sulfates, nitrates, chlorides, ammonium) and for each source type using the carbon mass balance approach. Size resolved emission factors were also acquired using a novel high duty cycle particle time-of-flight technique (ePTOF). Black carbon and brown carbon absorption emission factors and absorption Angström exponents were measured using filter loading and scattering corrected attenuation at 370 nm and 880 nm with a dual spot aethalometer (Magee Scientific AE-33). The results indicate that open garbage burning is a strong emitter of organic aerosol, black carbon, and internally mixed particle phase hydrogen chloride (HCl). Emissions of HCl were attributed to the presence chlorinated plastics. The primarily coal fired brick kilns were found to be large emitters of sulfate but large differences in the organic and light absorbing component of emissions were observed between the two kiln types investigated (technologically advanced vs. traditional). These results, among others, bring on-line and field-tested aerosol emission measurements to an area of atmoshperic research dominated by off-line or laboratory based measurements.
-
Directory of Open Access Journals (Sweden)
Rina Wu
2016-02-01
Full Text Available Studying the influencing factors of carbon dioxide emissions is not only practically but also theoretically crucial for establishing regional carbon-reduction policies, developing low-carbon economy and solving the climate problems. Therefore, we used a geographical detector model which is consists of four parts, i.e., risk detector, factor detector, ecological detector and interaction detector to analyze the effect of these social economic factors, i.e., GDP, industrial structure, urbanization rate, economic growth rate, population and road density on the increase of energy consumption carbon dioxide emissions in industrial sector in Inner Mongolia northeast of China. Thus, combining with the result of four detectors, we found that GDP and population more influence than economic growth rate, industrial structure, urbanization rate and road density. The interactive effect of any two influencing factors enhances the increase of the carbon dioxide emissions. The findings of this research have significant policy implications for regions like Inner Mongolia.
-
Explanatory factors of CO2 per capita emission inequality in the European Union
International Nuclear Information System (INIS)
Padilla, Emilio; Duro, Juan Antonio
2013-01-01
The design of European mitigation policies requires a detailed examination of the factors explaining the unequal emissions in the different countries. This research analyzes the evolution of inequality in CO 2 emissions per capita in the European Union (EU-27) in the period 1990–2009 and its explanatory factors. For this purpose, we decompose the Theil index of inequality into the contributions of the different Kaya factors. The decomposition is also applied to the inequality between and within groups of countries (North Europe, South Europe, and East Europe). The analysis shows an important reduction in inequality, to a large extent due to the smaller differences between groups and because of the lower contribution of the energy intensity factor. The importance of the GDP per capita factor increases and becomes the main explanatory factor. However, within the different groups of countries the carbonization index appears to be the most relevant factor in explaining inequalities. The policy implications of the results are discussed. - Highlights: • CO 2 inequality in EU-27 (Theil index) is decomposed into explanatory (Kaya) factors. • It decreases more between than within regions (North, South, East). • Energy intensity contribution falls and turns negative. GDP pc becomes main factor. • Carbonization makes most relevant contribution to inequality within groups. • Policy implications on feasibility of agreements and mitigation policy are discussed
-
International Nuclear Information System (INIS)
1992-11-01
A draft rule for the regulation of emissions of organic hazardous air pollutants (HAP's) from chemical processes of the synthetic organic chemical manufacturing industry (SOCMI) is being proposed under the authority of Sections 112, 114, 116, and 301 of the Clean Air Act, as amended in 1990. The volume of the Background Information Document presents the results of the national impacts assessment for the proposed rule
-
Measurements of air pollution emission factors for marine transportation in SECA
Alföldy, B.; Lööv, J.; Lagler, F.; Mellqvist, J.; Berg, N.; Beecken, J.; Weststrate, J.H.; Duyzer, J.H.; Bencs, L.; Horemans, B.; Cavalli, F.; Putaud, J.P.; Janssens-Maenhout, G.; Csordas, A.P.; Grieken, R. van; Borowiak, A.; Hjorth, J.
2013-01-01
The chemical composition of the plumes of seagoing ships was measured during a two week long measure- ment campaign in the port of Rotterdam, Hoek van Holland The Netherlands, in September 2009. Altogether, 497 ships were monitored and a statistical evaluation of emission factors (g kg−1 fuel) was
-
Fontaras, Georgios; Franco, Vicente; Dilara, Panagiota; Martini, Giorgio; Manfredi, Urbano
2014-01-01
The mass emissions of CO2 and regulated pollutants (NOX, HC, CO, PM) of thirteen Euro 5 compliant passenger cars (seven gasoline, six Diesel) were measured on a chassis dynamometer. The vehicles were driven repeatedly over the European type-approval driving cycle (NEDC) and the more dynamic WMTC and CADC driving cycles. Distance-specific emission factors were derived for each pollutant and sub-cycle which were subsequently compared to the corresponding emission factors provided by the referen...
-
DEFF Research Database (Denmark)
Doltra, J; Olesen, Jørgen E; Báez, D
2015-01-01
Mitigation of greenhouse gas emissions from agriculture should be assessed across cropping systems and agroclimatic regions. In this study, we investigate the ability of the FASSET model to analyze differences in the magnitude of N2O emissions due to soil, climate and management factors in cereal...... on the seasonal soil N2O fluxes than the environmental factors. Overall, in its current version FASSET reproduced the effects of the different factors investigated on the cumulative seasonal soil N2O emissions but temporally it overestimated emissions from nitrification and denitrification on particular days when...... soil operations, ploughing or fertilization, took place. The errors associated with simulated daily soil N2O fluxes increased with the magnitude of the emissions. For resolving causes of differences in simulated and measured fluxes more intensive and temporally detailed measurements of N2O fluxes...
-
Directory of Open Access Journals (Sweden)
Shichun Xu
2017-09-01
Full Text Available We decompose factors affecting China’s energy-related air pollutant (NOx, PM2.5, and SO2 emission changes into different effects using structural decomposition analysis (SDA. We find that, from 2005 to 2012, investment increased NOx, PM2.5, and SO2 emissions by 14.04, 7.82 and 15.59 Mt respectively, and consumption increased these emissions by 11.09, 7.98, and 12.09 Mt respectively. Export and import slightly increased the emissions on the whole, but the rate of the increase has slowed down, possibly reflecting the shift in China’s foreign trade structure. Energy intensity largely reduced NOx, PM2.5, and SO2 emissions by 12.49, 14.33 and 23.06 Mt respectively, followed by emission efficiency that reduces these emissions by 4.57, 9.08, and 17.25 Mt respectively. Input-output efficiency slightly reduces the emissions. At sectoral and sub-sectoral levels, consumption is a great driving factor in agriculture and commerce, whereas investment is a great driving factor in transport, construction, and some industrial subsectors such as iron and steel, nonferrous metals, building materials, coking, and power and heating supply. Energy intensity increases emissions in transport, chemical products and manufacturing, but decreases emissions in all other sectors and subsectors. Some policies arising from our study results are discussed.
-
Study of Radiation Induced Radicals in HAP and β-TCP Based Bone Graft Materials by ERP Spectroscopy
International Nuclear Information System (INIS)
Maltar-Strmecki, N.; Matkovic, I.
2013-01-01
Calcium phosphates such as beta-tricalcium phosphate (β-TCP) and hydroxyapatite (HAP) are frequently used as dental implants due to proven excellent biocompatibility. Because of their resorption in the body and direct contact with tissues, in order to inactivate bacteria, fungal spores and viruses, they are usually sterilized by γ-irradiation. However, literature provides little information about effects of γ-irradiation on the formation and stability of the free radicals in the bone graft materials during and after sterilization procedure. In this study EPR (electron paramagnetic resonance) spectroscopy was used to investigate HAP and β-TCP based dental implants present on the market. Eight dental graft materials present on the market were investigated: Bioresorb R Macropore, Poresorb R -TCP, Easy-Graft T M and Cerasorb R synthetic β-tricalcium phosphates, Easy-Graft T M crystal and Ossceram R two phase synthetic CaP consisting of 60 % HAP and 40 % β-TCP, and Dexabone R and Bio-Oss R bone graft material of bovine origin. EPR study shows that this is the only technique for characterization of free radicals that can simultaneously determine not only the presence and content, but also the position and the structure of free radicals formed by γ-sterilization in the investigated materials, as well as the paramagnetic substitutions incorporated in the materials during the synthesis (such as Mn 2+ , Fe 3+ or Cr 2+ ). Additionally, EPR provides information on stability of irradiation-induced radicals (CO 2 - , trapped H-atoms, NO 3 2 etc.) and processes for reducing them. Results show that EPR should be considered as a valuable technique in improving the quality of bone graft materials, which must be sterile, and to offer the high quality, efficacy and reliable materials to the patients.(author)
-
Factors affecting CO2 emission from the power sector of selected countries in Asia and the Pacific
International Nuclear Information System (INIS)
Shrestha, Ram M.; Anandarajah, Gabrial; Liyanage, Migara H.
2009-01-01
This study analyzes the key factors behind the CO 2 emissions from the power sector in fifteen selected countries in Asia and the Pacific using the Log-Mean Divisia Index method of decomposition. The roles of changes in economic output, electricity intensity of the economy, fuel intensity of power generation and generation structure are examined in the evolution of CO 2 emission from the power sector of the selected countries during 1980-2004. The study shows that the economic growth was the dominant factor behind the increase in CO 2 emission in ten of the selected countries (i.e., Australia, China, India, Japan, Malaysia, Pakistan, South Korea, Singapore, Thailand and Vietnam, while the increasing electricity intensity of the economy was the main factor in three countries (Bangladesh, Indonesia and Philippines). Structural changes in power generation were found to be the main contributor to changes in the CO 2 emission in the case of Sri Lanka and New Zealand.
-
Isoprene Emission Factors for Subtropical Street Trees for Regional Air Quality Modeling.
Dunn-Johnston, Kristina A; Kreuzwieser, Jürgen; Hirabayashi, Satoshi; Plant, Lyndal; Rennenberg, Heinz; Schmidt, Susanne
2016-01-01
Evaluating the environmental benefits and consequences of urban trees supports their sustainable management in cities. Models such as i-Tree Eco enable decision-making by quantifying effects associated with particular tree species. Of specific concern are emissions of biogenic volatile organic compounds, particularly isoprene, that contribute to the formation of photochemical smog and ground level ozone. Few studies have quantified these potential disservices of urban trees, and current models predominantly use emissions data from trees that differ from those in our target region of subtropical Australia. The present study aimed (i) to quantify isoprene emission rates of three tree species that together represent 16% of the inventoried street trees in the target region; (ii) to evaluate outputs of the i-Tree Eco model using species-specific versus currently used, generic isoprene emission rates; and (iii) to evaluate the findings in the context of regional air quality. Isoprene emission rates of (Myrtaceae) and (Proteaceae) were 2.61 and 2.06 µg g dry leaf weight h, respectively, whereas (Sapindaceae) was a nonisoprene emitter. We substituted the generic isoprene emission rates with these three empirical values in i-Tree Eco, resulting in a 182 kg yr (97%) reduction in isoprene emissions, totaling 6284 kg yr when extrapolated to the target region. From these results we conclude that care has to be taken when using generic isoprene emission factors for urban tree models. We recommend that emissions be quantified for commonly planted trees, allowing decision-makers to select tree species with the greatest overall benefit for the urban environment. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.
-
Variability in Light-Duty Gasoline Vehicle Emission Factors from Trip-Based Real-World Measurements.
Liu, Bin; Frey, H Christopher
2015-10-20
Using data obtained with portable emissions measurements systems (PEMS) on multiple routes for 100 gasoline vehicles, including passenger cars (PCs), passenger trucks (PTs), and hybrid electric vehicles (HEVs), variability in tailpipe emission rates was evaluated. Tier 2 emission standards are shown to be effective in lowering NOx, CO, and HC emission rates. Although PTs are larger, heavier vehicles that consume more fuel and produce more CO2 emissions, they do not necessarily produce more emissions of regulated pollutants compared to PCs. HEVs have very low emission rates compared to tier 2 vehicles under real-world driving. Emission factors vary with cycle average speed and road type, reflecting the combined impact of traffic control and traffic congestion. Compared to the slowest average speed and most congested cycles, optimal emission rates could be 50% lower for CO2, as much as 70% lower for NOx, 40% lower for CO, and 50% lower for HC. There is very high correlation among vehicles when comparing driving cycles. This has implications for how many cycles are needed to conduct comparisons between vehicles, such as when comparing fuels or technologies. Concordance between empirical and predicted emission rates using the U.S. Environmental Protection Agency's MOVES model was also assessed.
-
2012-04-19
... consistent with other rule text. 28. The definitions of ``Non-mercury (Hg) HAP metals'' and ``Oil'' in...-mercury (Hg) HAP metals'' and add the definition ``Oil'' to read as follows: Sec. 63.10042 What definitions apply to this subpart? * * * * * Non-mercury (Hg) HAP metals means Antimony (Sb), Arsenic (As...
-
Energy Technology Data Exchange (ETDEWEB)
Gayathri, K. [Department of Physics and Astronomy, University of Texas at San Antonio, San Antonio, TX 78249 (United States); Kumar, G.A., E-mail: ajith@gakumar.net [Department of Physics and Astronomy, University of Texas at San Antonio, San Antonio, TX 78249 (United States); Department of Atomic and Molecular Spectroscopy, Manipal University, Manipal 576104 (India); Northwest Vista College, 3535 N Ellison Dr, San Antonio, TX 78251 (United States); Manrique, Solange Ivette Rivera [Instituto Politécnico Nacional (IPN), Av. Luis Enrique Erro S/N, Unidad Profesional Adolfo López Mateos, Zacatenco, Delegación Gustavo A. Madero, C.P. 07738, Ciudad de México 2009-2010 (Mexico); Santhosh, C. [Department of Atomic and Molecular Spectroscopy, Manipal University, Manipal 576104 (India); Sardar, Dhiraj K. [Department of Physics and Astronomy, University of Texas at San Antonio, San Antonio, TX 78249 (United States)
2017-05-15
Trivalent Nd doped hydroxyapatite (HAp) nanoparticles were prepared by a hydrothermal method using calcium nitrate and diammonium phosphate as precursors. Well crystallized nanoparticles of size less than 200 nm with hexagonal plate and rod morphologies were obtained at a reaction temperature of 180 °C. Under 808 nm excitation the nanoparticles exhibit strong near infrared emission at 1064 nm. All the emission spectral properties such as emission intensity and fluorescence decay time are found to decrease with Nd{sup 3+} concentration. In Hap 0.5% Nd shows the highest decay time of 159 μs and highest emission at 1064 nm emission.
-
International Nuclear Information System (INIS)
Gayathri, K.; Kumar, G.A.; Manrique, Solange Ivette Rivera; Santhosh, C.; Sardar, Dhiraj K.
2017-01-01
Trivalent Nd doped hydroxyapatite (HAp) nanoparticles were prepared by a hydrothermal method using calcium nitrate and diammonium phosphate as precursors. Well crystallized nanoparticles of size less than 200 nm with hexagonal plate and rod morphologies were obtained at a reaction temperature of 180 °C. Under 808 nm excitation the nanoparticles exhibit strong near infrared emission at 1064 nm. All the emission spectral properties such as emission intensity and fluorescence decay time are found to decrease with Nd 3+ concentration. In Hap 0.5% Nd shows the highest decay time of 159 μs and highest emission at 1064 nm emission.
-
Energy Technology Data Exchange (ETDEWEB)
Duro, J.A. [Universitat Rovira i Virgili, Reus (Spain). Dept. d' Economia; Universitat de Barcelona (Spain). Inst. de Analisis Economico; Padilla, E. [Universitat de Barcelona (Spain). Dept. d' Economia Aplicada
2006-03-15
In this paper, we provide a methodology for decomposing international inequalities in per capita CO{sub 2} emissions into Kaya (multiplicative) factors and two interaction terms. We use the Theil index of inequality and show that this decomposition methodology can be extended for analyzing between- and within-group inequality components. We can thus analyze the factors behind inequalities in per capita CO{sub 2} emissions across countries, between groups of countries and within groups of countries. The empirical illustration for international data suggests some points. Firstly, international inequality in per capita CO{sub 2} emissions is mainly attributable to inequalities in per capita income levels, which helps to explain its recent reduction, while differences in carbon intensity of energy and energy intensity have made a less significant contribution. This result is strongly influenced by the performance of China and India. Secondly, the between-group inequality component, which is the biggest component, is also largely explained by the income factor. Thirdly, the within-group inequality component increased slightly during the period, something mainly due to the change in the income factor and the interaction terms in a few regions. (author)
-
International Nuclear Information System (INIS)
Zhang, Zhaoguo; Jin, Xiaocui; Yang, Qingxiang; Zhang, Yi
2013-01-01
Corporate excessive energy consumption and emissions are negative externality problems, with the basic countermeasure of establishing a series of institutional programs to promote corporate energy conservation and emissions reduction. This paper analyzes the influence of institutional factors such as laws, tax policies, credit policies, government subsidies, media supervision and marketization degree on corporate energy conservation and emissions reduction from the institutional perspective. The data, from 84 listed Chinese chemical and steel companies from 2006 to 2010, was analyzed using both a fixed effect model and the generalized method of moments (GMM) model. The empirical results demonstrate that these institutional factors positively affect corporate energy conservation and emissions reduction. Specifically, four factors – tax policies, government subsidies, credit policies and media supervision – have a significant positive relationship with corporate energy conservation and emissions reduction; whereas laws and marketization degree exhibit no significant effects. The research findings are theoretically and practically significant to the Chinese government with regard to improving the institutional environment and promoting corporate energy conservation and emissions reduction. - Highlights: ► Theoretical analysis of the influence of institutional factors based on NIE. ► Empirical analysis of the influence of institutional factors on ECER by regression. ► Economic measures and public opinions have positive influence on ECER in China. ► Laws and the degree of marketization have weak influence on ECER in China
-
Energy Technology Data Exchange (ETDEWEB)
Kwon, Tae-Hyeong [The Korea Transport Institute (KOTI), 2311 Daehwa-dong, Ilsan-gu, Goyang-Shi, Gyeonggi-do, 411-701 (Korea, Republic of)
2005-04-15
Carbon dioxide (CO{sub 2}) is the most important of the greenhouse gases that are causing global warming. The transport sector currently accounts for more than one-quarter of CO{sub 2} emissions and more importantly its share in total emissions is increasing in most countries. This paper investigates the key factors in the change in CO{sub 2} emissions from car travel in Great Britain over the last 30 years. It attempts to disentangle determinants of growth in CO{sub 2} emissions from car travel, which has the largest share of emissions in road transport. The study is based on various decomposition analyses, starting from the IPAT identity. As summarised in the IPAT identity, the degree of the Impact of human activity on the environment is determined by changes in Population, Affluence (per-capita consumption) and Technology (environmental impact per quantity of consumption). In the case of CO{sub 2} emissions from car travel in Great Britain, the affluence (A) factor (car driving distance per person) was a dominant force for the growth of emissions over the last 30 years. Not only do people travel longer distances by cars than 30 years ago, but car occupancy rates have also decreased, contributing to the growth of car driving distance per person. Although technology (T) factors such as fuel efficiency and fuel substitution to diesel fuel partly cancelled out these growth effects of affluence factors, this contribution was relatively small. However, in the 1990s there emerged a different pattern in the trend. Of the affluence (A) factors, the growth rate of car trip distance per person weakened considerably. As for the technology (T) effect, the carbon intensity of car driving kept decreasing over this period. Therefore, although CO{sub 2} emissions from car travel (I) continued to increase, the growth rate became substantially lower than in the earlier periods. More detailed investigation into the determinants of both affluence (A) factors and technology (T
-
International Nuclear Information System (INIS)
1992-11-01
A draft rule for the regulation of emissions of organic hazardous air pollutants (HAP's) from chemical processes of the synthetic organic chemical manufacturing industry (SOCMI) is being proposed under the authority of Sections 112, 114, 116, and 301 of the Clean Air Act, as amended in 1990. The volume of the Background Information Document presents discussions of control technologies used in the industry and the costs of those technologies
-
Generating samples for association studies based on HapMap data
Directory of Open Access Journals (Sweden)
Chen Yixuan
2008-01-01
Full Text Available Abstract Background With the completion of the HapMap project, a variety of computational algorithms and tools have been proposed for haplotype inference, tag SNP selection and genome-wide association studies. Simulated data are commonly used in evaluating these new developed approaches. In addition to simulations based on population models, empirical data generated by perturbing real data, has also been used because it may inherit specific properties from real data. However, there is no tool that is publicly available to generate large scale simulated variation data by taking into account knowledge from the HapMap project. Results A computer program (gs was developed to quickly generate a large number of samples based on real data that are useful for a variety of purposes, including evaluating methods for haplotype inference, tag SNP selection and association studies. Two approaches have been implemented to generate dense SNP haplotype/genotype data that share similar local linkage disequilibrium (LD patterns as those in human populations. The first approach takes haplotype pairs from samples as inputs, and the second approach takes patterns of haplotype block structures as inputs. Both quantitative and qualitative traits have been incorporated in the program. Phenotypes are generated based on a disease model, or based on the effect of a quantitative trait nucleotide, both of which can be specified by users. In addition to single-locus disease models, two-locus disease models have also been implemented that can incorporate any degree of epistasis. Users are allowed to specify all nine parameters in a 3 × 3 penetrance table. For several commonly used two-locus disease models, the program can automatically calculate penetrances based on the population prevalence and marginal effects of a disease that users can conveniently specify. Conclusion The program gs can effectively generate large scale genetic and phenotypic variation data that can be
-
Amon, Barbara; Zechmeister-Boltenstern, Sophie; Kasper, Martina; Foldal, Cecilie; Schiefer, Jasmin; Kitzler, Barbara; Schwarzl, Bettina; Zethner, Gerhard; Anderl, Michael; Sedy, Katrin; Gaugitsch, Helmut; Dersch, Georg; Baumgarten, Andreas; Haas, Edwin; Kiese, Ralf
2016-04-01
Results from a previous project "FarmClim" highlight that the IPCC default emission factor is not able to reflect region specific N2O emissions from Austrian arable soils. The methodology is limited in identifying hot spots and hot moments of N2O emissions. When estimations are based on default emission factors no recommendations can be given on optimisation measures that would lead to a reduction of soil N2O emissions. The better the knowledge is about Nitrogen and Carbon budgets in Austrian agricultural managed soils the better the situation can be reflected in the Austrian GHG emission inventory calculations. Therefore national and regionally modelled emission factors should improve the evidence for national deviation from the IPCC default emission factors and reduce the uncertainties. The overall aim of NitroAustria is to identify the drivers for N2O emissions on a regional basis taking different soil types, climate, and agricultural management into account. We use the LandscapeDNDC model to update the N2O emission factors for N fertilizer and animal manure applied to soils. Key regions in Austria were selected and region specific N2O emissions calculated. The model runs at sub-daily time steps and uses data such as maximum and minimum air temperature, precipitation, radiation, and wind speed as meteorological drivers. Further input data are used to reflect agricultural management practices, e.g., planting/harvesting, tillage, fertilizer application, irrigation and information on soil and vegetation properties for site characterization and model initialization. While at site scale, arable management data (crop cultivation, rotations, timings etc.) is obtained by experimental data from field trials or observations, at regional scale such data need to be generated using region specific proxy data such as land use and management statistics, crop cultivations and yields, crop rotations, fertilizer sales, manure resulting from livestock units etc. The farming
-
Gu, Ying; Wang, Luojia; Ren, Pan; Zhang, Junxiang; Zhang, Tiancai; Martin, Olivier J F; Gong, Qihuang
2012-05-09
The mechanism of using the anisotropic Purcell factor to control the spontaneous emission linewidths in a four-level atom is theoretically demonstrated; if the polarization angle bisector of the two dipole moments lies along the axis of large/small Purcell factor, destructive/constructive interference narrows/widens the fluorescence center spectral lines. Large anisotropy of the Purcell factor, confined in the subwavelength optical mode volume, leads to rapid spectral line narrowing of atom approaching a metallic nanowire, nanoscale line width pulsing following periodically varying decay rates near a periodic metallic nanostructure, and dramatic modification on the spontaneous emission spectrum near a custom-designed resonant plasmon nanostructure. The combined system opens a good perspective for applications in ultracompact active quantum devices.
-
Giechaskiel, Barouch
2018-01-01
Particulate matter (PM), and in particular ultrafine particles, have a negative impact on human health. The contribution of vehicle PM emissions to air pollution is typically quantified with emission inventories, which need vehicle emission factors as input. Heavy-duty vehicles, although they represent a small percentage of the vehicle population in nearly every major country, contribute the majority of the on-road PM emissions. However, the published data of modern heavy-duty vehicle emissions are scarce, and for the newest Euro VI technologies, almost non-existent. The main objective of this paper is to present Solid Particle Number (SPN) emission factors from Euro VI heavy-duty vehicles using diesel, Compressed Natural Gas (CNG), or Liquefied Natural Gas (LNG). Urban, rural and motorway (highway) emissions were determined on the road at various European cities using SPN Portable Emission Measurement Systems (PEMS). Additional tests on a heavy-duty chassis dynamometer showed that the solid sub-23 nm fraction, which is not covered at the moment in the European regulation, is high, especially for CNG engines. The significant contribution of regeneration events and the effect of ambient temperature and engine cold-start on particle emissions were also discussed. PMID:29425174
-
Directory of Open Access Journals (Sweden)
Barouch Giechaskiel
2018-02-01
Full Text Available Particulate matter (PM, and in particular ultrafine particles, have a negative impact on human health. The contribution of vehicle PM emissions to air pollution is typically quantified with emission inventories, which need vehicle emission factors as input. Heavy-duty vehicles, although they represent a small percentage of the vehicle population in nearly every major country, contribute the majority of the on-road PM emissions. However, the published data of modern heavy-duty vehicle emissions are scarce, and for the newest Euro VI technologies, almost non-existent. The main objective of this paper is to present Solid Particle Number (SPN emission factors from Euro VI heavy-duty vehicles using diesel, Compressed Natural Gas (CNG, or Liquefied Natural Gas (LNG. Urban, rural and motorway (highway emissions were determined on the road at various European cities using SPN Portable Emission Measurement Systems (PEMS. Additional tests on a heavy-duty chassis dynamometer showed that the solid sub-23 nm fraction, which is not covered at the moment in the European regulation, is high, especially for CNG engines. The significant contribution of regeneration events and the effect of ambient temperature and engine cold-start on particle emissions were also discussed.
-
Giechaskiel, Barouch
2018-02-09
Particulate matter (PM), and in particular ultrafine particles, have a negative impact on human health. The contribution of vehicle PM emissions to air pollution is typically quantified with emission inventories, which need vehicle emission factors as input. Heavy-duty vehicles, although they represent a small percentage of the vehicle population in nearly every major country, contribute the majority of the on-road PM emissions. However, the published data of modern heavy-duty vehicle emissions are scarce, and for the newest Euro VI technologies, almost non-existent. The main objective of this paper is to present Solid Particle Number (SPN) emission factors from Euro VI heavy-duty vehicles using diesel, Compressed Natural Gas (CNG), or Liquefied Natural Gas (LNG). Urban, rural and motorway (highway) emissions were determined on the road at various European cities using SPN Portable Emission Measurement Systems (PEMS). Additional tests on a heavy-duty chassis dynamometer showed that the solid sub-23 nm fraction, which is not covered at the moment in the European regulation, is high, especially for CNG engines. The significant contribution of regeneration events and the effect of ambient temperature and engine cold-start on particle emissions were also discussed.
-
Jimenez, Jorge; Farias, Oscar; Quiroz, Roberto; Yañez, Jorge
2017-07-01
In south-central Chile, wood stoves have been identified as an important source of air pollution in populated areas. Eucalyptus (Eucalyptus globulus), Chilean oak (Nothofagus oblique), and mimosa (Acacia dealbata) were burned in a single-chamber slow-combustion wood stove at a controlled testing facility located at the University of Concepción, Chile. In each experiment, 2.7-3.1 kg of firewood were combusted while continuously monitoring temperature, exhaust gases, burn rate, and collecting particulate matter samples in Teflon filters under isokinetic conditions for polycyclic aromatic hydrocarbon and levoglucosan analyses. Mean particulate matter emission factors were 2.03, 4.06, and 3.84 g/kg dry wood for eucalyptus, oak, and mimosa, respectively. The emission factors were inversely correlated with combustion efficiency. The mean emission factors of the sums of 12 polycyclic aromatic hydrocarbons in particle phases were 1472.5, 2134.0, and 747.5 μg/kg for eucalyptus, oak, and mimosa, respectively. Fluoranthene, pyrene, benzo[a]anthracene, and chrysene were present in the particle phase in higher proportions compared with other polycyclic aromatic hydrocarbons that were analyzed. Mean levoglucosan emission factors were 854.9, 202.3, and 328.0 mg/kg for eucalyptus, oak, and mimosa, respectively. Since the emissions of particulate matter and other pollutants were inversely correlated with combustion efficiency, implementing more efficient technologies would help to reduce air pollutant emissions from wood combustion. Residential wood burning has been identified as a significant source of air pollution in populated areas. Local wood species are combusted for home cooking and heating, which releases several toxic air pollutants, including particulate matter, carbon monoxide, and polycyclic aromatic hydrocarbons. Air pollutant emissions depend on the type of wood and the technology and operational conditions of the wood stove. A better understanding of emissions from
-
DEFF Research Database (Denmark)
Batra, Tushar; Schaltz, Erik
2014-01-01
to the surroundings also increase with increase in the quality factor. In this paper, first analytical expressions are developed for comparing magnetic emissions at different quality factors. Theoretical and simulation (Comsol) results show comparatively lower increase for the magnetic field emissions to the linear...
-
DEFF Research Database (Denmark)
Batra, Tushar; Schaltz, Erik
2014-01-01
Inductive power transfer is non-contact transfer of energy by means of magnetic fields. A higher secondary side quality factor at fixed input current ensures a linear increase in power transfer across the air gap. But also at the same time magnetic emissions to the surroundings increase. First...... of all in this paper an analytic expression for comparing the magnetic emissions at different quality factors is introduced. It is shown with help of simulations on Comsol that emissions have a lower increase as compared to linear increase in the power transferred with the quality factor as suggested...
-
Study of greenhouse gases emission factor for nuclear power chain of China
International Nuclear Information System (INIS)
Ma Zhonghai; Pan Ziqiang; Xie Jianlun; Xiu Binglin
2001-01-01
The Greenhouse Gases Emission Factor (GGEF) for nuclear power chain of China is calculated based on Life Cycle Analysis method and the definition of full energy chain. There is no greenhouse gases released directly from nuclear power plant. The greenhouse gases emission from nuclear power plant is mainly from coal-fired electricity supply to nuclear power plant for its normal operation and the production of construction materials those are used in the nuclear power plant. The total GGEF of nuclear power chain in China is 13.71 g-co 2 /kWh. It is necessary to regulate un-rational power source mix and to use the energy sources in rational way for reducing the greenhouse gas effect. Nuclear power for electricity generation is one of effective ways to reduce greenhouse gases emission and retard the greenhouse effect
-
International Nuclear Information System (INIS)
Zhang Lei; Wang Shuxiao; Wu Qingru; Meng Yang; Yang Hai; Wang Fengyang; Hao Jiming
2012-01-01
Non-ferrous metal smelting takes up a large proportion of the anthropogenic mercury emission inventory in China. Zinc, lead and copper smelting are three leading sources. Onsite measurements of mercury emissions were conducted for six smelters. The mercury emission factors were 0.09–2.98 g Hg/t metal produced. Acid plants with the double-conversion double-absorption process had mercury removal efficiency of over 99%. In the flue gas after acid plants, 45–88% was oxidized mercury which can be easily scavenged in the flue gas scrubber. 70–97% of the mercury was removed from the flue gas to the waste water and 1–17% to the sulfuric acid product. Totally 0.3–13.5% of the mercury in the metal concentrate was emitted to the atmosphere. Therefore, acid plants in non-ferrous metal smelters have significant co-benefit on mercury removal, and the mercury emission factors from Chinese non-ferrous metal smelters were probably overestimated in previous studies. - Highlights: ► Acid plants in smelters provide significant co-benefits for mercury removal (over 99%). ► Most of the mercury in metal concentrates for smelting ended up in waste water. ► Previously published emission factors for Chinese metal smelters were probably overestimated. - Acid plants in smelters have high mercury removal efficiency, and thus mercury emission factors for Chinese non-ferrous metal smelters were probably overestimated.
-
Development of Hot Exhaust Emission Factors for Iranian-Made Euro-2 Certified Light-Duty Vehicles.
Banitalebi, Ehsan; Hosseini, Vahid
2016-01-05
Emission factors (EFs) are fundamental, necessary data for air pollution research and scenario implementation. With the vision of generating national EFs of the Iranian transportation system, a portable emission measurement system (PEMS) was used to develop the basic EFs for a statistically significant sample of Iranian gasoline-fueled privately owned light duty vehicles (LDVs) operated in Tehran. A smaller sample size of the same fleet was examined by chassis dynamometer (CD) bag emission measurement tests to quantify the systematic differences between the PEMS and CD methods. The selected fleet was tested over four different routes of uphill highways, flat highways, uphill urban streets, and flat urban streets. Real driving emissions (RDEs) and fuel consumption (FC) rates were calculated by weighted averaging of the results from each route. The activity of the fleet over each route type was assumed as a weighting factor. The activity data were obtained from a Tehran traffic model. The RDEs of the selected fleet were considerably higher than the certified emission levels of all vehicles. Differences between Tehran real driving cycles and the New European Driving Cycle (NEDC) was attributed to the lower loading of NEDC. A table of EFs based on RDEs was developed for the sample fleet.
-
Fontaras, Georgios; Franco, Vicente; Dilara, Panagiota; Martini, Giorgio; Manfredi, Urbano
2014-01-15
The emissions of CO2 and regulated pollutants (NOx, HC, CO, PM) of thirteen Euro 5 compliant passenger cars (seven gasoline, six Diesel) were measured on a chassis dynamometer. The vehicles were driven repeatedly over the European type-approval driving cycle (NEDC) and the more dynamic WMTC and CADC driving cycles. Distance-specific emission factors were derived for each pollutant and sub-cycle, and these were subsequently compared to the corresponding emission factors provided by the reference European models used for vehicle emission inventory compilation (COPERT and HBEFA) and put in context with the applicable European emission limits. The measured emissions stayed below the legal emission limits when the type-approval cycle (NEDC) was used. Over the more dynamic cycles (considered more representative of real-world driving) the emissions were consistently higher but in most cases remained below the type-approval limit. The high NOx emissions of Diesel vehicles under real-world driving conditions remain the main cause for environmental concern regarding the emission profile of Euro 5 passenger cars. Measured emissions of NOx exceeded the type-approval limits (up to 5 times in extreme cases) and presented significantly increased average values (0.35 g/km for urban driving and 0.56 g/km for motorway driving). The comparison with the reference models showed good correlation in all cases, a positive finding considering the importance of these tools in emission monitoring and policy-making processes. © 2013. Published by Elsevier B.V. All rights reserved.
-
Size-resolved particle emission factors for individual ships
Jonsson, Åsa M.; Westerlund, Jonathan; Hallquist, Mattias
2011-07-01
In these experiments size-resolved emission factors for particle number (EFPN) and mass (EFPM) have been determined for 734 individual ship passages for real-world dilution. The method used is an extractive sampling method of the passing ship plumes where particle number/mass and CO2 were measured with high time resolution (1 Hz). The measurements were conducted on a small island located in the entrance to the port of Gothenburg (N57.6849, E11.838), the largest harbor in Scandinavia. This is an emission control area (ECA) and in close vicinity to populated areas. The average EFPN and EFPM were 2.55 ± 0.11 × 1016 (kg fuel)-1 and 2050 ± 110 mg (kg fuel)-1, respectively. The determined EF for ships with multiple passages showed a great reproducibility. Size-resolved EFPN were peaking at small particle sizes ˜35 nm. Smaller particle sizes and hence less mass were observed by a gas turbine equipped ship compared to diesel engine equipped ships. On average 36 to 46% of the emitted particles by number were non-volatile and 24% by mass (EFPN 1.16 ± 0.19 × 1016 [kg fuel]-1 and EFPM 488 ± 73 mg [kg fuel]-1, respectively). This study shows a great potential to gain large data-sets regarding ship emission determining parameters that can improve current dispersion modeling for health assessments on local and regional scales. The global contributions of total and non-volatile particle mass from shipping using this extensive data-set from an ECA were estimated to be at least 0.80 Tgy-1 and 0.19 Tgy-1.
-
Averaged emission factors for the Hungarian car fleet
Energy Technology Data Exchange (ETDEWEB)
Haszpra, L. [Inst. for Atmospheric Physics, Budapest (Hungary); Szilagyi, I. [Central Research Inst. for Chemistry, Budapest (Hungary)
1995-12-31
The vehicular emission of non-methane hydrocarbon (NMHC) is one of the largest anthropogenic sources of NMHC in Hungary and in most of the industrialized countries. Non-methane hydrocarbon plays key role in the formation of photo-chemical air pollution, usually characterized by the ozone concentration, which seriously endangers the environment and human health. The ozone forming potential of the different NMHCs differs from each other significantly, while the NMHC composition of the car exhaust is influenced by the fuel and engine type, technical condition of the vehicle, vehicle speed and several other factors. In Hungary the majority of the cars are still of Eastern European origin. They represent the technological standard of the 70`s, although there are changes recently. Due to the long-term economical decline in Hungary the average age of the cars was about 9 years in 1990 and reached 10 years by 1993. The condition of the majority of the cars is poor. In addition, almost one third (31.2 %) of the cars are equipped with two-stroke engines which emit less NO{sub x} but much more hydrocarbon. The number of cars equipped with catalytic converter was negligible in 1990 and is slowly increasing only recently. As a consequence of these facts the traffic emission in Hungary may differ from that measured in or estimated for the Western European countries and the differences should be taken into account in the air pollution models. For the estimation of the average emission of the Hungarian car fleet a one-day roadway tunnel experiment was performed in the downtown of Budapest in summer, 1991. (orig.)
-
2010-07-01
... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Example Logs for Recording Leather Finish Use and HAP Content 1 Figure 1 to Subpart TTTT of Part 63 Protection of Environment ENVIRONMENTAL... Finishing Operations Part 63, Subpt. TTTT, Fig. 1 Figure 1 to Subpart TTTT of Part 63—Example Logs for...
-
40 CFR 63.5797 - How do I determine the organic HAP content of my resins and gel coats?
2010-07-01
... single value, you may use that value to determine compliance. If a separate measurement of the total... provided by the material supplier or manufacturer as a range, you must use the upper limit of the range for determining compliance. If a separate measurement of the total organic HAP content, such as an analysis of the...
-
Particulate emission factor: A case study of a palm oil mill boiler
International Nuclear Information System (INIS)
Chong, W.C.; Rashid, M.; Ramli, M.; Zainura, Z.N.; NorRuwaida, J.
2010-01-01
A study to investigate the particulate emission from a boiler of a palm oil mill plant equipped with a multi-cyclones particulate arrest or was performed and reported in this paper. The particulate emission concentration was measured at the outlet of a 8 mt/ hr capacity water-tube typed boiler of a palm oil mill plant processing 27mt/ hr of fresh fruit bunch (FFB). The particulate sample was collected iso-kinetically using the USEPA method 5 sampling train through a sampling port made at the duct of the exiting flue gas between the boiler and a multi-cyclones unit. Results showed that the particulate emission rates exiting the boiler varied from 0.09 to 0.60 g/s with an average of 0.29 + 0.18 g/ s. While the average particulate emission concentration exiting the boiler was 12.1 + 7.36 g/ Nm 3 (corrected to 7 % oxygen concentration), ranging from 3.62 to 25.3 g/ Nm 3 (at 7 % O 2 ) of the flue gas during the measurement. Based on the 27 mt/ hr FFB processed and the capacity of the boiler of 8mt steam/ hr, the calculated particulate emission factor was 39 g particulate/ mt FFB processed or 131 g particulate/ mt boiler capacity, respectively. In addition, based on the finding and in order to comply with the emission limits of 0.4 g/ Nm 3 , the collection efficiency of any given particulate emission pollution control system to consider for the mill will be from 87 to 98 %, which is not easily achievable with the existing multi-cyclones unit. A considerable amount of efforts are still needed pertaining to the particulate emission control problem in the industry. (author)
-
Future Emissions from Railway Traffic
DEFF Research Database (Denmark)
Sorenson, Spencer C.
1998-01-01
In investigation of the expected development in factors which influence railway energy consumption and emissions. Traffic factors such as train speed, load, an occupancy were considered. Tehcnical factors such an emissions factors, fleet composition and train weight were also considered. An estim......In investigation of the expected development in factors which influence railway energy consumption and emissions. Traffic factors such as train speed, load, an occupancy were considered. Tehcnical factors such an emissions factors, fleet composition and train weight were also considered...
-
Driving factors of carbon dioxide emissions and the impact from Kyoto Protocol
Energy Technology Data Exchange (ETDEWEB)
Grunewald, Nicole [Goettingen Univ. (Germany). Dept. of Economics; Martinez-Zarzoso, Inmaculada [Jaume I Univ. (Spain). International Economics Institute
2009-08-15
In the last two decades increasing attention has been paid to the relationship between environmental degradation and economic development. According to the Environmental Kuznets Curve (EKC) hypothesis this relationship may be described by an inverted-U curve. However, recent evidence rejects the EKC hypothesis for GHG emissions in a broad sense. In this paper we aim to investigate whether the EKC behavior for CO2 emissions could be proved on the behalf of institutional regulations. We analyze the driving factors of CO2 for developed and developing countries to test the theory of the EKC in the context of environmental regulations using a static and dynamic panel data model. We consider the Kyoto Protocol and the Clean Development Mechanism (CDM). The results from this study indicate that the Kyoto obligations have a reducing effect on CO2 emissions in developed and developing countries. (orig.)
-
Kuikman, P.J.; Hoek, van der K.W.; Smit, A.; Zwart, K.B.
2006-01-01
Emissions of nitrous oxide (N2O) in the Netherlands are reported to the UNFCCC on the basis of a country specific methodology. In this study we have identified and analysed the values for emission factors in measurement from in the Netherlands in the period 1993 – 2003. The overall averaged emission
-
Decomposition of CO2 Emission Factors in Baoding
Li, Wei; Wang, xuyang; Zhang, Hongzhi
2018-01-01
Baoding, as one of the first “five provinces and eight cities” low carbon pilot cities, undertakes an important task and mission. The urgent task is to explore a peak route and emission reduction path suitable for Baoding’s own development, so as to provide reference for the construction of low-carbon pilot cities. At present, the carbon emissions of Baoding city and its subordinate districts and counties are not clear, and the carbon emissions, change trends and emission characteristics of various industries have not been systematically studied. This lead researcherscan not carry out further attribution analysis, the prediction of future emissions trends and put forward specific measures to reduce emissions are impossible.If the government can not accurately and comprehensively understand the problems faced in the construction and development of low-carbon cities, it is difficult to fundamentally put forward effective emission reduction policies and measures.
-
Imhof, David; Weingartner, Ernest; Ordónez, Carlos; Gehrig, Robert; Hill, Matz; Buchmann, Brigitte; Baltensperger, Urs
2005-11-01
Extended field measurements of particle number (size distribution of particle diameters, D, in the range between 18 nm and 10 microm), surface area concentrations, and PM1 and PM10 mass concentrations were performed in Switzerland to determine traffic emissions using a comprehensive set of instruments. Measurements took place at roads with representative traffic regimes: at the kerbside of a motorway (120 km h(-1)), a highway (80-100 km h(-1)), and in an urban area with stop-and-go traffic (0-50 km h(-1)) regulated by light signals. Mean diurnal variations showed that the highest pollutant concentrations were during the morning rush hours, especially of the number density in the nanoparticle size range (D real-life" emission factors were derived using NOx concentrations to calculate dilution factors. Particle number and volume emission factors of different size ranges (18-50 nm, 18-100 nm, and 18-300 nm) were derived for the total vehicle fleet and separated into a light-duty (LDV) and a heavy-duty vehicle (HDV) contribution. The total particle number emissions per vehicle were found to be about 11.7-13.5 x 10(14) particles km(-1) for constant speed (80-120 km h(-1) and 3.9 x 10(14) particles km(-1) for urban driving conditions. LDVs showed higher emission factors at constant high speed than under urban disturbed traffic flow. In contrast, HDVs emitted more air pollutants during deceleration and acceleration processes in stop-and-go traffic than with constant speed of about 80 km h(-1). On average, one HDV emits a 10-30 times higher amount of particulate air pollutants (in terms of both number and volume) than one LDV.
-
Wang, Hai-Kun; Fu, Li-Xin; Zhou, Yu; Lin, Xin; Chen, Ai-Zhong; Ge, Wei-hu; Du, Xuan
2008-10-01
Emission from 7 typical light-duty vehicles under actual driving conditions was monitored using a portable emission measurement system to gather data for characterization of the real world vehicle emission in Shenzhen, including the effects of driving modes on vehicle emission, comparison of fuel consumption based emission factors (g x L(-1) with mileage based emission factors (g x km(-1)), and the average emission factors of the monitored vehicles. The acceleration and deceleration modes accounted for 66.7% of total travel time, 80.3% of traveling distance and 74.6%-79.2% of vehicle emission; the acceleration mode contributed more than other driving modes. The fuel based emission factors were less dependent on the driving speed; they may be utilized in building macro-scale vehicle emission inventory with smaller sensitivity to the vehicle driving conditions. The effect of vehicle technology on vehicle emission was significant; the emission factors of CO, HC and NO(x) of carbureted vehicles were 19.9-20.5, 5.6-26.1 and 1.8-2.0 times the more advanced vehicles of Euro II, respectively. Using the ECE + EUDC driving cycle would not produce the desired real-world emission rates of light duty vehicles in a typical Chinese city.
-
Guodoong Liu; Yuncong Li; Kati W. Migliaccio; Ying Ouyang; Ashok K. Alva
2011-01-01
Ammonia (NH3) emissions from fertilized soils are a costly problem that is undermining agricultural and ecological sustainability worldwide. Ammonia emissions from crop production have been reliably documented in recent years. However, insufficient efforts have been made to determine the factors most influential in facilitating NH3 emissions. The goal of this study was...
-
Regulation of hazardous air pollutants emitted from fossil-fired boilers
International Nuclear Information System (INIS)
Hendrickson, P.L.; Daellenbach, K.K.
1993-01-01
The changes made in section 112 of the Clean Air Act by the 1990 Amendments to the Act will affect the regulation of hazardous air pollutants (HAPs) emitted by fossil-fired boilers. The 1990 Amendments designated 189 chemicals/compounds as HAPS. Major and area sources of these pollutants in categories designated by the Environmental Protection Agency (EPA) will be subject to emission standards set by EPA. Industrial and institutional/commercial boilers are two such categories of HAPs designated by EPA for which emission standards will be issued. Fossil-fired boilers can emit a variety of HAPS. All or a portion of such emissions that exceed designated thresholds are likely to be regulated. This paper discusses how the 1990 amendments impact fossil-fired boilers. The steps are outlined which can be taken by owners of industrial and institutional/commercial boilers before the final emission standards are issued. These steps include participation in EPA's standard setting process, participation in EPA's early reduction program to delay the time when compliance with the maximum achievable control technology (MACT) standard is required, and consideration of any planned modifications to a facility which might subject that facility to a MACT standard set in advance of the EPA-set standard
-
Directory of Open Access Journals (Sweden)
Ü. Niinemets
2010-06-01
Full Text Available In models of plant volatile isoprenoid emissions, the instantaneous compound emission rate typically scales with the plant's emission potential under specified environmental conditions, also called as the emission factor, ES. In the most widely employed plant isoprenoid emission models, the algorithms developed by Guenther and colleagues (1991, 1993, instantaneous variation of the steady-state emission rate is described as the product of ES and light and temperature response functions. When these models are employed in the atmospheric chemistry modeling community, species-specific ES values and parameter values defining the instantaneous response curves are often taken as initially defined. In the current review, we argue that ES as a characteristic used in the models importantly depends on our understanding of which environmental factors affect isoprenoid emissions, and consequently need standardization during experimental ES determinations. In particular, there is now increasing consensus that in addition to variations in light and temperature, alterations in atmospheric and/or within-leaf CO2 concentrations may need to be included in the emission models. Furthermore, we demonstrate that for less volatile isoprenoids, mono- and sesquiterpenes, the emissions are often jointly controlled by the compound synthesis and volatility. Because of these combined biochemical and physico-chemical drivers, specification of ES as a constant value is incapable of describing instantaneous emissions within the sole assumptions of fluctuating light and temperature as used in the standard algorithms. The definition of ES also varies depending on the degree of aggregation of ES values in different parameterization schemes (leaf- vs. canopy- or region-scale, species vs. plant functional type levels and various
-
Wang, Yang; Xing, Zhenyu; Zhao, Shuhui; Zheng, Mei; Mu, Chao; Du, Ke
2016-03-15
Accurately quantifying black carbon (BC) emission factors (EFs) is a prerequisite for estimation of BC emission inventory. BC EFs determined by measuring BC at the roadside or chasing a vehicle on-road may introduce large uncertainty for low emission vehicles. In this study, BC concentrations were measured inside the tailpipe of gasoline vehicles with different engine sizes under different driving modes to determine the respective EFs. BC EFs ranged from 0.005-7.14 mg/kg-fuel under the speeds of 20-70 km/h, 0.05-28.95 mg/kg-fuel under the accelerations of 0.5-1.5m/s(2). Although the water vapor in the sampling stream could result in an average of 12% negative bias, the BC EFs are significantly lower than the published results obtained with roadside or chasing vehicle measurement. It is suggested to conduct measurement at the tailpipe of gasoline vehicles instead of in the atmosphere behind the vehicles to reduce the uncertainty from fluctuation in ambient BC concentration. Copyright © 2015 Elsevier B.V. All rights reserved.
-
Factors affecting ultraviolet-A photon emission from β-irradiated human keratinocyte cells.
Le, M; Mothersill, C E; Seymour, C B; Ahmad, S B; Armstrong, A; Rainbow, A J; McNeill, F E
2015-08-21
The luminescence intensity of 340±5 nm photons emitted from HaCaT (human keratinocyte) cells was investigated using a single-photon-counting system during cellular exposure to (90)Y β-particles. Multiple factors were assessed to determine their influence upon the quantity and pattern of photon emission from β-irradiated cells. Exposure of 1 x 10(4) cells/5 mL to 703 μCi resulted in maximum UVA photoemission at 44.8 x 10(3)±2.5 x 10(3) counts per second (cps) from live HaCaT cells (background: 1-5 cps); a 16-fold increase above cell-free controls. Significant biophoton emission was achieved only upon stimulation and was also dependent upon presence of cells. UVA luminescence was measured for (90)Y activities 14 to 703 μCi where a positive relationship between photoemission and (90)Y activity was observed. Irradiation of live HaCaT cells plated at various densities produced a distinct pattern of emission whereby luminescence increased up to a maximum at 1 x 10(4) cells/5 mL and thereafter decreased. However, this result was not observed in the dead cell population. Both live and dead HaCaT cells were irradiated and were found to demonstrate different rates of photon emission at low β activities (⩽400 μCi). Dead cells exhibited greater photon emission rates than live cells which may be attributable to metabolic processes taking place to modulate the photoemissive effect. The results indicate that photon emission from HaCaT cells is perturbed by external stimulation, is dependent upon the activity of radiation delivered, the density of irradiated cells, and cell viability. It is postulated that biophoton emission may be modulated by a biological or metabolic process.
-
Wood, Andrew R; Perry, John R B; Tanaka, Toshiko; Hernandez, Dena G; Zheng, Hou-Feng; Melzer, David; Gibbs, J Raphael; Nalls, Michael A; Weedon, Michael N; Spector, Tim D; Richards, J Brent; Bandinelli, Stefania; Ferrucci, Luigi; Singleton, Andrew B; Frayling, Timothy M
2013-01-01
Genome-wide association (GWA) studies have been limited by the reliance on common variants present on microarrays or imputable from the HapMap Project data. More recently, the completion of the 1000 Genomes Project has provided variant and haplotype information for several million variants derived from sequencing over 1,000 individuals. To help understand the extent to which more variants (including low frequency (1% ≤ MAF 1000 Genomes imputation, respectively, and 9 and 11 that reached a stricter, likely conservative, threshold of P1000 Genomes genotype data modestly improved the strength of known associations. Of 20 associations detected at P1000 Genomes imputed data and one was nominally more strongly associated in HapMap imputed data. We also detected an association between a low frequency variant and phenotype that was previously missed by HapMap based imputation approaches. An association between rs112635299 and alpha-1 globulin near the SERPINA gene represented the known association between rs28929474 (MAF = 0.007) and alpha1-antitrypsin that predisposes to emphysema (P = 2.5×10(-12)). Our data provide important proof of principle that 1000 Genomes imputation will detect novel, low frequency-large effect associations.
-
S. P. Urbanski
2013-01-01
In the US, wildfires and prescribed burning present significant challenges to air regulatory agencies attempting to achieve and maintain compliance with air quality regulations. Fire emission factors (EF) are essential input for the emission models used to develop wildland fire emission inventories. Most previous studies quantifying wildland fire EF of temperate...
-
International Nuclear Information System (INIS)
Ogle, Stephen M; Hartman, Melannie; Spencer, Shannon; Buendia, Leandro; Butterbach-Bahl, Klaus; Breidt, F Jay; Yagi, Kazuyuki; Nayamuth, Rasack; Wirth, Tom; Smith, Pete
2013-01-01
Developing countries face many challenges when constructing national inventories of greenhouse gas (GHG) emissions, such as lack of activity data, insufficient measurements for deriving country-specific emission factors, and a limited basis for assessing GHG mitigation options. Emissions from agricultural production are often significant sources in developing countries, particularly soil nitrous oxide, and livestock enteric and manure methane, in addition to wetland rice methane. Consequently, estimating GHG emissions from agriculture is an important part of constructing developing country inventories. While the challenges may seem insurmountable, there are ways forward such as: (a) efficiently using resources to compile activity data by combining censuses and surveys; (b) using a tiered approach to measure emissions at appropriately selected sites, coupled with modeling to derive country-specific emission factors; and (c) using advanced software systems to guide compilers through the inventory process. With a concerted effort by compilers and assistance through capacity-building efforts, developing country compilers could produce transparent, accurate, complete, consistent and comparable inventories, as recommended by the IPCC (Intergovernmental Panel on Climate Change). In turn, the resulting inventories would provide the foundation for robust GHG mitigation analyses and allow for the development of nationally appropriate mitigation actions and low emission development strategies. (letter)
-
The 1990 Clean Air Act Amendments require EPA to develop standards for major emission sources of 189 hazardous air pollutants (HAPs). EPA has identified the flexible polyurethane foam industry as a large emitter of HAPs and has slated the industry for regulation under Title III, ...
-
Factors affecting temporal H2S emission at construction and demolition (C&D) debris landfills.
Xu, Qiyong; Townsend, Timothy
2014-02-01
Odor problems associated with H2S emissions often result in odor complaints from nearby residents of C&D debris landfills, especially in the early morning. As part of a field study conducted on H2S removal ability using different cover materials, daily and seasonal H2S emissions through a soil cover layer were monitored at a C&D debris landfill to investigate factors affecting H2S emissions. H2S emission rates were not a constant, but varied seasonally, with an average emission rate of 4.67×10(-6)mgm(-2)s(-1). During a the 10-month field study, as the H2S concentration increased from 140ppm to about 3500ppm underneath the cover soil in the testing cell, H2S emissions ranged from zero to a maximum emission rate of 1.24×10(-5)mgm(-2)s(-1). Continuous emission monitoring indicated that H2S emissions even changed over time throughout the day, generally increasing from morning to afternoon, and were affected by soil moisture and temperature. Laboratory experiments were also conducted to investigate the effects of H2S concentration and cover soil moisture content on H2S emissions. The results showed that increased soil moisture reduced H2S emissions by retarding H2S migration through cover soil and dissolving H2S into soil water. The field study also indicated that due to atmospheric dispersion, high H2S emissions may not cause odor problems. Copyright © 2013 Elsevier Ltd. All rights reserved.
-
Genotype Imputation for Latinos Using the HapMap and 1000 Genomes Project Reference Panels
Directory of Open Access Journals (Sweden)
Xiaoyi eGao
2012-06-01
Full Text Available Genotype imputation is a vital tool in genome-wide association studies (GWAS and meta-analyses of multiple GWAS results. Imputation enables researchers to increase genomic coverage and to pool data generated using different genotyping platforms. HapMap samples are often employed as the reference panel. More recently, the 1000 Genomes Project resource is becoming the primary source for reference panels. Multiple GWAS and meta-analyses are targeting Latinos, the most populous and fastest growing minority group in the US. However, genotype imputation resources for Latinos are rather limited compared to individuals of European ancestry at present, largely because of the lack of good reference data. One choice of reference panel for Latinos is one derived from the population of Mexican individuals in Los Angeles contained in the HapMap Phase 3 project and the 1000 Genomes Project. However, a detailed evaluation of the quality of the imputed genotypes derived from the public reference panels has not yet been reported. Using simulation studies, the Illumina OmniExpress GWAS data from the Los Angles Latino Eye Study and the MACH software package, we evaluated the accuracy of genotype imputation in Latinos. Our results show that the 1000 Genomes Project AMR+CEU+YRI reference panel provides the highest imputation accuracy for Latinos, and that also including Asian samples in the panel can reduce imputation accuracy. We also provide the imputation accuracy for each autosomal chromosome using the 1000 Genomes Project panel for Latinos. Our results serve as a guide to future imputation-based analysis in Latinos.
-
Energy Technology Data Exchange (ETDEWEB)
Chiang, Hung-Lung, E-mail: hlchiang@mail.cmu.edu.tw [Department of Health Risk Management, China Medical University, Taichung, Taiwan (China); Lin, Kuo-Hsiung [Department of Environmental Engineering and Science, Fooyin University, Kaohsiung, Taiwan (China)
2014-01-15
Highlights: • Recycling of waste printed circuit boards is an important issue. • Pyrolysis is an emerging technology for PCB treatment. • Emission factors of VOCs are determined for PCB pyrolysis exhaust. • Iron-Al{sub 2}O{sub 3} catalyst was employed for the exhaust control. -- Abstract: The printed circuit board (PCB) is an important part of electrical and electronic equipment, and its disposal and the recovery of useful materials from waste PCBs (WPCBs) are key issues for waste electrical and electronic equipment. Waste PCB compositions and their pyrolysis characteristics were analyzed in this study. In addition, the volatile organic compound (VOC) exhaust was controlled by an iron-impregnated alumina oxide catalyst. Results indicated that carbon and oxygen were the dominant components (hundreds mg/g) of the raw materials, and other elements such as nitrogen, bromine, and copper were several decades mg/g. Exhaust constituents of CO, H{sub 2}, CH{sub 4}, CO{sub 2}, and NOx, were 60–115, 0.4–4.0, 1.1–10, 30–95, and 0–0.7 mg/g, corresponding to temperatures ranging from 200 to 500 °C. When the pyrolysis temperature was lower than 300 °C, aromatics and paraffins were the major species, contributing 90% of ozone precursor VOCs, and an increase in the pyrolysis temperature corresponded to a decrease in the fraction of aromatic emission factors. Methanol, ethylacetate, acetone, dichloromethane, tetrachloromethane and acrylonitrile were the main species of oxygenated and chlorinated VOCs. The emission factors of some brominated compounds, i.e., bromoform, bromophenol, and dibromophenol, were higher at temperatures over 400 °C. When VOC exhaust was flowed through the bed of Fe-impregnated Al{sub 2}O{sub 3}, the emission of ozone precursor VOCs could be reduced by 70–80%.
-
Directory of Open Access Journals (Sweden)
Yong Wang
2018-05-01
Full Text Available Household carbon emissions are important components of total carbon emissions. The consumer side of energy-saving emissions reduction is an essential factor in reducing carbon emissions. In this paper, the carbon emissions coefficient method and Consumer Lifestyle Approach (CLA were used to calculate the total carbon emissions of households in 30 provinces of China from 2006 to 2015, and based on the extended Stochastic Impacts by Regression on Population, Affluence, and Technology (STIRPAT model, the factors influencing the total carbon emissions of households were analyzed. The results indicated that, first, over the past ten years, the energy and products carbon emissions from China’s households have demonstrated a rapid growth trend and that regional distributions present obvious differences. Second, China’s energy carbon emissions due to household consumption primarily derived from the residents’ consumption of electricity and coal; China’s products household carbon emissions primarily derived from residents’ consumption of the high carbon emission categories: residences, food, transportation and communications. Third, in terms of influencing factors, the number of households in China plays a significant role in the total carbon emissions of China’s households. The ratio of children 0–14 years old and gender ratio (female = 100 are two factors that reflect the demographic structure, have significant effects on the total carbon emissions of China’s households, and are all positive. Gross Domestic Product (GDP per capita plays a role in boosting the total carbon emissions of China’s households. The effect of the carbon emission intensity on total household carbon emissions is positive. The industrial structure (the proportion of secondary industries’ added value to the regional GDP has curbed the growth of total carbon emissions from China’s household consumption. The results of this study provide data to support the
-
Stochastic Industrial Source Detection Using Lower Cost Methods
Thoma, E.; George, I. J.; Brantley, H.; Deshmukh, P.; Cansler, J.; Tang, W.
2017-12-01
Hazardous air pollutants (HAPs) can be emitted from a variety of sources in industrial facilities, energy production, and commercial operations. Stochastic industrial sources (SISs) represent a subcategory of emissions from fugitive leaks, variable area sources, malfunctioning processes, and improperly controlled operations. From the shared perspective of industries and communities, cost-effective detection of mitigable SIS emissions can yield benefits such as safer working environments, cost saving through reduced product loss, lower air shed pollutant impacts, and improved transparency and community relations. Methods for SIS detection can be categorized by their spatial regime of operation, ranging from component-level inspection to high-sensitivity kilometer scale surveys. Methods can be temporally intensive (providing snap-shot measures) or sustained in both time-integrated and continuous forms. Each method category has demonstrated utility, however, broad adoption (or routine use) has thus far been limited by cost and implementation viability. Described here are a subset of SIS methods explored by the U.S EPA's next generation emission measurement (NGEM) program that focus on lower cost methods and models. An emerging systems approach that combines multiple forms to help compensate for reduced performance factors of lower cost systems is discussed. A case study of a multi-day HAP emission event observed by a combination of low cost sensors, open-path spectroscopy, and passive samplers is detailed. Early field results of a novel field gas chromatograph coupled with a fast HAP concentration sensor is described. Progress toward near real-time inverse source triangulation assisted by pre-modeled facility profiles using the Los Alamos Quick Urban & Industrial Complex (QUIC) model is discussed.