The effect of chalk on the finger-hold friction coefficient in rock climbing.

Science.gov (United States)

Amca, Arif Mithat; Vigouroux, Laurent; Aritan, Serdar; Berton, Eric

2012-11-01

The main purpose of this study was to examine the effect of chalk on the friction coefficient between climber's fingers and two different rock types (sandstone and limestone). The secondary purpose was to investigate the effects of humidity and temperature on the friction coefficient and on the influence of chalk. Eleven experienced climbers took part in this study and 42 test sessions were performed. Participants hung from holds which were fixed on a specially designed hang board. The inclination of the hang board was progressively increased until the climber's hand slipped from the holds. The angle of the hang board was simultaneously recorded by using a gyroscopic sensor and the friction coefficient was calculated at the moment of slip. The results showed that there was a significant positive effect of chalk on the coefficient of friction (+18.7% on limestone and +21.6% on sandstone). Moreover sandstone had a higher coefficient of friction than limestone (+15.6% without chalk, +18.4% with chalk). These results confirmed climbers' belief that chalk enhances friction. However, no correlation with humidity/temperature and friction coefficient was noted which suggested that additional parameters should be considered in order to understand the effects of climate on finger friction in rock climbing.

The influence of normal fault on initial state of stress in rock mass

Directory of Open Access Journals (Sweden)

Tajduś Antoni

2016-03-01

Full Text Available Determination of original state of stress in rock mass is a very difficult task for rock mechanics. Yet, original state of stress in rock mass has fundamental influence on secondary state of stress, which occurs in the vicinity of mining headings. This, in turn, is the cause of the occurrence of a number of mining hazards, i.e., seismic events, rock bursts, gas and rock outbursts, falls of roof. From experience, it is known that original state of stress depends a lot on tectonic disturbances, i.e., faults and folds. In the area of faults, a great number of seismic events occur, often of high energies. These seismic events, in many cases, are the cause of rock bursts and damage to the constructions located inside the rock mass and on the surface of the ground. To estimate the influence of fault existence on the disturbance of original state of stress in rock mass, numerical calculations were done by means of Finite Element Method. In the calculations, it was tried to determine the influence of different factors on state of stress, which occurs in the vicinity of a normal fault, i.e., the influence of normal fault inclination, deformability of rock mass, values of friction coefficient on the fault contact. Critical value of friction coefficient was also determined, when mutual dislocation of rock mass part separated by a fault is impossible. The obtained results enabled formulation of a number of conclusions, which are important in the context of seismic events and rock bursts in the area of faults.

The influence of normal fault on initial state of stress in rock mass

Science.gov (United States)

Tajduś, Antoni; Cała, Marek; Tajduś, Krzysztof

2016-03-01

Determination of original state of stress in rock mass is a very difficult task for rock mechanics. Yet, original state of stress in rock mass has fundamental influence on secondary state of stress, which occurs in the vicinity of mining headings. This, in turn, is the cause of the occurrence of a number of mining hazards, i.e., seismic events, rock bursts, gas and rock outbursts, falls of roof. From experience, it is known that original state of stress depends a lot on tectonic disturbances, i.e., faults and folds. In the area of faults, a great number of seismic events occur, often of high energies. These seismic events, in many cases, are the cause of rock bursts and damage to the constructions located inside the rock mass and on the surface of the ground. To estimate the influence of fault existence on the disturbance of original state of stress in rock mass, numerical calculations were done by means of Finite Element Method. In the calculations, it was tried to determine the influence of different factors on state of stress, which occurs in the vicinity of a normal fault, i.e., the influence of normal fault inclination, deformability of rock mass, values of friction coefficient on the fault contact. Critical value of friction coefficient was also determined, when mutual dislocation of rock mass part separated by a fault is impossible. The obtained results enabled formulation of a number of conclusions, which are important in the context of seismic events and rock bursts in the area of faults.

United States National Waste Terminal Storage argillaceous rock studies

International Nuclear Information System (INIS)

Brunton, G.D.

1981-01-01

The past and present argillaceous rock studies for the US National Waste Terminal Storage Program consist of: (1) evaluation of the geological characteristics of several widespread argillaceous formations in the United States; (2) laboratory studies of the physical and chemical properties of selected argillaceous rock samples; and (3) two full-scale in situ surface heater experiments that simulate the emplacement of heat-generating radioactive waste in argillaceous rock

United States National Waste Terminal Storage argillaceous rock studies

International Nuclear Information System (INIS)

Brunton, G.D.

1979-01-01

The past and present argillaceous rock studies for the US National Waste Terminal Storage Program consist of: (1) evaluation of the geological characteristics of several widespread argillaceous formations in the United States; (2) laboratory studies of the physical and chemical properties of selected argillaceous rock samples; and (3) two full-scale in-situ surface heater experiments that simulate the emplacement of heat-generating radioactive waste in argillaceous rock

Controls on fault zone structure and brittle fracturing in the foliated hanging wall of the Alpine Fault

Science.gov (United States)

Williams, Jack N.; Toy, Virginia G.; Massiot, Cécile; McNamara, David D.; Smith, Steven A. F.; Mills, Steven

2018-04-01

Three datasets are used to quantify fracture density, orientation, and fill in the foliated hanging wall of the Alpine Fault: (1) X-ray computed tomography (CT) images of drill core collected within 25 m of its principal slip zones (PSZs) during the first phase of the Deep Fault Drilling Project that were reoriented with respect to borehole televiewer images, (2) field measurements from creek sections up to 500 m from the PSZs, and (3) CT images of oriented drill core collected during the Amethyst Hydro Project at distances of ˜ 0.7-2 km from the PSZs. Results show that within 160 m of the PSZs in foliated cataclasites and ultramylonites, gouge-filled fractures exhibit a wide range of orientations. At these distances, fractures are interpreted to have formed at relatively high confining pressures and/or in rocks that had a weak mechanical anisotropy. Conversely, at distances greater than 160 m from the PSZs, fractures are typically open and subparallel to the mylonitic or schistose foliation, implying that fracturing occurred at low confining pressures and/or in rocks that were mechanically anisotropic. Fracture density is similar across the ˜ 500 m width of the field transects. By combining our datasets with measurements of permeability and seismic velocity around the Alpine Fault, we further develop the hierarchical model for hanging-wall damage structure that was proposed by Townend et al. (2017). The wider zone of foliation-parallel fractures represents an outer damage zone that forms at shallow depths. The distinct inner damage zone. This zone is interpreted to extend towards the base of the seismogenic crust given that its width is comparable to (1) the Alpine Fault low-velocity zone detected by fault zone guided waves and (2) damage zones reported from other exhumed large-displacement faults. In summary, a narrow zone of fracturing at the base of the Alpine Fault's hanging-wall seismogenic crust is anticipated to widen at shallow depths, which is

Fabrication and Operation of Microfluidic Hanging-Drop Networks.

Science.gov (United States)

Misun, Patrick M; Birchler, Axel K; Lang, Moritz; Hierlemann, Andreas; Frey, Olivier

2018-01-01

The hanging-drop network (HDN) is a technology platform based on a completely open microfluidic network at the bottom of an inverted, surface-patterned substrate. The platform is predominantly used for the formation, culturing, and interaction of self-assembled spherical microtissues (spheroids) under precisely controlled flow conditions. Here, we describe design, fabrication, and operation of microfluidic hanging-drop networks.

Acute pulmonary emphysema in death by hanging: a morphometric digital study.

Science.gov (United States)

Castiglioni, Claudia; Baumann, Pia; Fracasso, Tony

2016-09-01

Acute pulmonary emphysema (APE) has been described in cases of mechanical asphyxia such as ligature or manual strangulation but not in cases of hanging. In this study, we wanted to verify by morphometric digital analysis of lung tissue whether APE occurs in death by hanging.We investigated 16 cases of hanging (eight complete, eight incomplete), 10 cases of freshwater drowning (positive control group), and 10 cases of acute external bleeding (negative control group). Tissue sections were obtained from each pulmonary lobe. For each slide, five fields were randomly selected. The area of every alveolar space was measured by image analysis software. The mean alveolar area (MAA) was calculated for each group.In incomplete hanging, MAA was significantly higher than that observed in complete hanging and similar to the one observed in freshwater drowning.APE in cases of incomplete hanging can be considered as a sign of vitality. The high number of conditions that can cause alveolar distension (that were excluded in this study) limits the applicability of this vital sign in the routine forensic practice.

The automation of the "making safe" process in South African hard-rock underground mine

CSIR Research Space (South Africa)

Teleka, SR

2011-07-01

Full Text Available In South African hard-rock mines, best practice dictates that the hanging-walls be inspected after blasting. This process is known as ‘making safe’ and although intended to save lives, it is laborious and subjective. Pressure is placed on the barrer...

The discovery and exploration of Hang Son Doong

Energy Technology Data Exchange (ETDEWEB)

Limbert, H.; Limbert, D.; Hieu, N.; Phai, V. V.; Kinh Bac, D.; Phuong, T. H.; Granger, D.

2016-08-01

Hang Son Doong is located in the Phong Nha Ke Bang Limestone Massif in Quang Binh Province, Central Vietnam. Cave exploration by British cavers has been continuous in this area since 1990. Hang Son Doong is part of the Phong Nha Cave system which runs from the southern end of the National Park near the Lao border to the final resurgence at Phong Nha Cave. (Author)

Length of a Hanging Cable

Directory of Open Access Journals (Sweden)

Eric Costello

2011-01-01

Full Text Available The shape of a cable hanging under its own weight and uniform horizontal tension between two power poles is a catenary. The catenary is a curve which has an equation defined by a hyperbolic cosine function and a scaling factor. The scaling factor for power cables hanging under their own weight is equal to the horizontal tension on the cable divided by the weight of the cable. Both of these values are unknown for this problem. Newton's method was used to approximate the scaling factor and the arc length function to determine the length of the cable. A script was written using the Python programming language in order to quickly perform several iterations of Newton's method to get a good approximation for the scaling factor.

Craniocervical injuries in judicial hangings: an anthropologic analysis of six cases.

Science.gov (United States)

Spence, M W; Shkrum, M J; Ariss, A; Regan, J

1999-12-01

Restoration projects and archaeologic excavations in two Canadian prisons resulted in the recovery of the skeletons of six felons executed by judicial hanging. Damage inflicted by hanging on various skeletal elements was observed. Among the injuries seen were fractures of the hyoid cornua, styloid processes, occipital bones, and cervical vertebral bodies (C2) and transverse processes (C1, C2, C3, and C5). Despite the general uniformity of the hanging technique, which involved a subaural knot, the trauma to the skeletal elements and the cause of death varied among individuals. Although some of this variation was probably due to minor differences in hanging practices, individual anatomic peculiarities of the victims likely also contributed.

SUICIDAL HANGING IN URBAN YOUTH : A PROSPECTIVE STUDY

Directory of Open Access Journals (Sweden)

Bhola Kumar Singh

2015-02-01

Full Text Available BACKGROUND : Suicide is among the top three causes of death among youth worldwide. Hanging is among the most common modes of suicide. OBJECTIVES: The purpose of this prospective study is to determine the Suicidal hanging in urban youth and determine the prevalence of suicidal hanging in our community. METHODS : In this descriptive, prospective, cross sectional study, all patients who pres ented to the department of emergency medicine with suicidal hanging during this study period of 12 months from January 2010 - December 2011 in . were included. RESULTS : Total number of males in the study is 32 (64%, females in the study is 18(36%. Mean age of the you th was 22.50± 8.15(SD years, Male 18.50± 12.15(SD years, Females 20.50 ±5.25(SD years; predominantly the patients were in the age group of 22 - 26 years. Number of male smokers in the study was 26 (81.25% female smokers were 4(22.22%, number of m ale alcoholics were 27(84.37% whereas female alcoholics were 6(33.33%, number of patients with pallor in males were 16(50% whereas females with pallor were 12(66.66%, number of males with skin changes were 6(18.75% when compared to females who had 8(4 4.44% skin changes, number of males wit oedema were 4(12.5% and 6(33.33% of females had oedema, the mean weight among males were 48±8.34kgs when compared to females which was 42±6.56kgs. Most of the patients who attempted suicide had varied personality issues from mood disorders to psychosis. CONCLUSION : There is significant percentage of patients who attempt suicide by hanging

Selected elements of rock burst state assessment in case studies from the Silesian hard coal mines

Energy Technology Data Exchange (ETDEWEB)

Jozef Kabiesz; Janusz Makowka [Central Mining Institute, Katowice (Poland)

2009-09-15

Exploitation of coal seams in the Upper Silesian Coal Basin is conducted in complex and difficult conditions. These difficulties are connected with the occurrence of many natural mining hazards and limitations resulting from the existing in this area surface infrastructure. One of the most important problems of Polish mining is the rock burst hazard and reliable evaluation of its condition. During long-years' mining practice in Poland a comprehensive system of evaluation and control of this hazard was developed. In the paper the main aspects of rock burst hazard state evaluation will be presented, comprising: 1) rock mass inclination for rock bursts, i.e., rock strength properties investigation, comprehensive parametric evaluation of rock mass inclination for rock bursts, prognosis of seismic events induced by mining operations, methods of computer-aided modelling of stress and rock mass deformation parameters distribution, strategic rock mass classification under rock burst degrees; 2) immediate seismic and rock burst hazard state evaluation, i.e., low diameter test drilling method, seismologic and seismoacoustic method, comprehensive method of rock burst hazard state evaluation, non-standard methods of evaluation; 3) legal aspects of rock burst hazard state evaluation. Selected elements of the hazard state evaluation system are illustrated with specific practical examples of their application. 11 refs., 14 figs.

Study of natural radioactivity in the rocks of Coorg District, Karnataka State

International Nuclear Information System (INIS)

Prakash, M.M; KaliPrasad, C.S.; Narayana, Y.

2016-01-01

The paper deals with the study of natural radioactivity in the rocks of Coorg district, Karnataka state. The level of terrestrial radiation are related to the geological composition of the region, and to the concentration of 226 Ra, 232 Th and 40 K in rock. Rocks are used in various construction activities, which also have these natural radionuclides. Hence, a study was done to assess the concentration of these radionuclides in rock samples. Coorg lies along the eastern slopes of Western Ghats, which is in the south western side of Karnataka state. The rock samples were collected from different locations of Coorg. The samples were crushed, ovendried and sieved through 240µm sieve. The sieved samples were sealed in a plastic container of 300ml and stored for 30 days

Sistem Informasi Akademik pada SMA Swasta Hang Tuah Belawan

OpenAIRE

Syarifuddin, Ruisya

2015-01-01

Perancangan Sistem Informasi Akademik pada SMA Swasta Hang Tuah Belawan ini bertujuan untuk mempermudah proses pencarian atau searching data dan informasi untuk seluruh Siswa SMA Swasta Hang Tuah Belawan yang mengalami kesulitan dalam memperoleh data mengenai masalah Akademik tersebut. Faasilitas yang terdapat dalam aplikasi ini berupa penyediaan data dan informasi mengenai beritaberita terbaru, profil agenda kegiatan, dan data-data yang berguna untuk kelangsungan belajar si...

DEEP HANGING WALL TRAPS-THE REMAINING PROMISSING TARGETS FOR OIL EXPLORATION IN THE NIGER DELTA

International Nuclear Information System (INIS)

Oton, S.W

2004-01-01

proven ultimate reserves in the Niger delta. KEYWORDS Niger Delta, hanging wall, deep fault, horizons, rollover anticline, contrary faults, footwall, collapsed crest, closure, accumulation, reserves, hydrocarbons, oil, condensate, gas, overpressures, source rock, targets, explore, offshore, exploration

Hanging Out with Which Friends? Friendship-Level Predictors of Unstructured and Unsupervised Socializing in Adolescence

Science.gov (United States)

Siennick, Sonja E.; Osgood, D. Wayne

2012-01-01

Companions are central to explanations of the risky nature of unstructured and unsupervised socializing, yet we know little about whom adolescents are with when hanging out. We examine predictors of how often friendship dyads hang out via multilevel analyses of longitudinal friendship-level data on over 5,000 middle schoolers. Adolescents hang out most with their most available friends and their most generally similar friends, not with their most at-risk or similarly at-risk friends. These findings vary little by gender and wave. Together, the findings suggest that the risks of hanging out stem from the nature of hanging out as an activity, not the nature of adolescents’ companions, and that hanging out is a context for friends’ mutual reinforcement of pre-existing characteristics. PMID:23204811

Hanging Out with Which Friends? Friendship-Level Predictors of Unstructured and Unsupervised Socializing in Adolescence.

Science.gov (United States)

Siennick, Sonja E; Osgood, D Wayne

2012-12-01

Companions are central to explanations of the risky nature of unstructured and unsupervised socializing, yet we know little about whom adolescents are with when hanging out. We examine predictors of how often friendship dyads hang out via multilevel analyses of longitudinal friendship-level data on over 5,000 middle schoolers. Adolescents hang out most with their most available friends and their most generally similar friends, not with their most at-risk or similarly at-risk friends. These findings vary little by gender and wave. Together, the findings suggest that the risks of hanging out stem from the nature of hanging out as an activity, not the nature of adolescents' companions, and that hanging out is a context for friends' mutual reinforcement of pre-existing characteristics.

Water collection behavior and hanging ability of bioinspired fiber.

Science.gov (United States)

Hou, Yongping; Chen, Yuan; Xue, Yan; Zheng, Yongmei; Jiang, Lei

2012-03-13

Since the water-collecting ability of the wetted cribellate spider capture silk is the result of a unique fiber structure, bioinspired fibers have been researched significantly so as to expose a new water-acquiring route in fogging-collection projects. However, the design of the geometry of bioinspired fiber is related to the ability of hanging drops, which has not been investigated in depth so far. Here, we fabricate bioinspired fibers to investigate the water collection behavior and the influence of geometry (i.e., periodicity of spindle knot) on the hanging-drop ability. We especially discuss water collection related to the periodicity of geometry on the bioinspired fiber. We reveal the length of the three phase contact line (TCL) at threshold conditions in conjunction with the maximal volume of a hanging drop at different modes. The study demonstrates that the geometrical structure of bioinspired fiber induces much stronger water hanging ability than that of uniform fiber, attributed to such special geometry that offers effectively an increasing TCL length or limits the contact length to be shorted. In addition, the geometry also improves the fog-collection efficiency by controlling tiny water drops to be collected in the large water drops at a given location.

The epidemiology of injury in hang-gliding and paragliding.

Science.gov (United States)

Rekand, Tiina

2012-01-01

Para- and hang-gliding are modern air sports that developed in the 20th century. Performers should possess technical skills and manage certified equipment for successful flight. Injuries may happen during the take-off, flight and landing. PubMed was searched using the search terms 'paragliding' and/or 'hang-gliding'. The reference lists of articles identified in the search strategy were also searched for relevant articles. The most common injuries are fractures, dislocations or sprains in the extremities, followed by spinal and head traumas. Multiple injuries after accidents are common. Collision with electrical wires may cause burn injuries. Fatal outcomes are caused by brain injuries, spinal cord injuries at the cervical level or aorta rupture. Accidents happen because of risk-taking behavior, lack of education or use of self-modified equipment. Observational studies have suggested the need for protection of the head, trunk and lower extremities. The measures proposed are often based on conclusions of observational studies and not proven through randomized studies. Better education along with focusing on possible risk factors will probably diminish the risks of hang- and paragliding. Large denominator-based case series, case-control and population-based studies are needed for assessment of the risks of hang- and paragliding. Copyright © 2012 S. Karger AG, Basel.

Realization methodology for optimal design of steel structures conveyors with hanging belt

Directory of Open Access Journals (Sweden)

Boslovyak P.V.

2016-03-01

Full Text Available Presents the results of optimum design of metal structures of the fixed conveyor with hanging belt. The analysis results optimum design of steel structures of stationary conveyor with hanging belt.

Calc-sodic zoning in rocks from Lagoa Real uranium Province, state of Bahia, Brazil

International Nuclear Information System (INIS)

Raposo, C.; Matos, E.C. de; Brito, W. de

1984-01-01

Preliminary studies of the lithogeochemistry, carried out on various deposits from the Uranium Province of Lagoa Real, show that in relation to the complex and multiphased processes of metasomatism, the sodic metasomatites are younger and were superposed on the potassic metasomatites. Such metasomatites developed in zones of extended and rejuvenated faults, after the transformation of the gnaisses, granitic rocks, amphibolites and ferruginous quartzites into various tectonites (mylonites, blastomylonites and protomylonites). The calcic metasomatism, subsequent to those phases, took place during the course of tectonothermal reactivations marking the termination of the principal metasomatic processes which aftected the rocks of Lagoa Real. The uranium deposit 'Jazida Laranjeiras', centrally situated in the Uranium Province of Lagoa Real is the only deposit in which the uranium mineralization is not intimately associated with the calcic metasomatism. Here, the ratio Na 2 O/CaO in the albitites is in the vicinity of 7,5 whereas in the other deposits this ratio decreases to values of about 1,5. The authors suggest calcic zoning (in the post-albitite phase) along the sigmoidal structure which localizes the uranium deposits, with an increase of the CaO content in the extreme parts of the structure - deposit 'Jazida Cachoeira' in the north and anomaly No. 02/12 in the south. Also suggested is the vertical zoning of calcium, whereby the intensity of the metasomatic phenomenon is increased towards the hanging wall side of the mieral parcel. (Author) [pt

Effectiveness of mesenchymal stems cells cultured by hanging drop vs. conventional culturing on the repair of hypoxic-ischemic-damaged mouse brains, measured by stemness gene expression

Directory of Open Access Journals (Sweden)

Lou Yongli

2016-01-01

Full Text Available In this study, we investigated the therapeutic effects of Human Mesenchymal Stem Cells (hMSCs cultured by hanging drop and conventional culturing methods on cerebellar repair in hypoxic-ischemic (HI brain injured mice. Real-time quantitative reverse transcription polymerase chain reaction (RT-qPCR was used to analyze the expression levels of three stemness genes, Oct4, Sox2 and Nanog, and the migration related gene CXCR4. MSC prepared by hanging drop or conventional techniques were administered intranasally to nine day old mice, and analyzed by MRI at day 28. Results indicate that the MSCs, especially the hanging drop cultured MSCs, significantly improved the mice’s cerebellar damage repair. MSCs derived from the hanging drop culture were smaller than those from the conventional culture. The gene expression levels were significantly increased for the MSCs derived from the hanging drop culture. The mechanism might relate to the fact that the hanging drop cultured MSCs can be kept in an undifferentiated state, resulting in its higher expression level of migration receptor of CXCR4.

Distribution of hanging garden vegetation associations on the Colorado Plateau, USA

Science.gov (United States)

James F. Fowler; N. L. Stanton; Ronald L. Hartman

2007-01-01

Hanging gardens are island-like habitats dominated by mesophytic-hydrophytic plant communities, growing on seeps on the xeric canyon walls of the Colorado Plateau in the American West. We measured the abundance of species and physical microhabitat characteristics of 73 individual hanging gardens during the growing seasons of 1991-1993. Cluster analysis of a simplified...

Kritik Mitos Tentang “Hang Tuah” Karya Amir Hamzah

OpenAIRE

Santosa, Puji

2014-01-01

This study reveals the myth criticism on rhyme "Hang Tuah", an Amir Hamzah’s work expressing Malay myth. The Malay myth found in the rhyme "Hang Tuah" is placed as a meeting place of myth criticism study which includes (1) the structure of the text, (2) figure with its ideology, (3) setting presenting the myth, (4) type of myth, (5) method the poet displays the myth, and (6) the benefit or function of myth. The six elements of the review are expected to contribute in exposing and describing t...

Hanging out with Which Friends? Friendship-Level Predictors of Unstructured and Unsupervised Socializing in Adolescence

Science.gov (United States)

Siennick, Sonja E.; Osgood, D. Wayne

2012-01-01

Companions are central to explanations of the risky nature of unstructured and unsupervised socializing, yet we know little about whom adolescents are with when hanging out. We examine predictors of how often friendship dyads hang out via multilevel analyses of longitudinal friendship-level data on over 5,000 middle schoolers. Adolescents hang out…

A case of the CT scanning of a suicidal hanging brain

International Nuclear Information System (INIS)

Kawamata, Masaharu; Murooka, Hiroshi; Tanabe, Yasuhiko.

1988-01-01

A CT scanning of a case of hanging brain is reported. A 63-year-old man, who had been maintained with Aspirin (30 mg every morning) for cerebral infarction, attempted suicide by hanging, but failed. Several hours later, he was admitted because of consciousness disturbance and so was examined by means of CT scanning. Plain CT scanning showed symmetrical multiple intracerebral hemorrhages. Hemorrhages were found in the subcortical region of the bilateral temporal lobes and in the subependymal region near the foramen of Monro or in the choroidal plexus. We speculated that these hemorrhages may be caused by the congestion of the intracranial venous system caused by squeezing both internal jugular veins by hanging. Past angiograms (1981) for cerebral infarction revealed neither AVM nor angioma. (author)

Ferguson rock slide buries California State Highway near Yosemite National Park

Science.gov (United States)

Harp, Edwin L.; Reid, Mark E.; Godt, Jonathan W.; DeGraff, Jerome V.; Gallegos, Alan J.

2008-01-01

During spring 2006, talus from the toe area of a rock-block slide of about 800,000 m3 buried California State Highway 140, one of the main routes into heavily-visited Yosemite National Park, USA. Closure of the highway for 92 days caused business losses of about 4.8 million USD. The rock slide, composed of slate and phyllite, moved slowly downslope from April to June 2006, creating a fresh head scarp with 9-12 m of displacement. Movement of the main rock slide, a re-activation of an older slide, was triggered by an exceptionally wet spring 2006, following a very wet spring 2005. As of autumn 2006, most of the main slide appeared to be at rest, although rocks occasionally continued to fall from steep, fractured rock masses at the toe area of the slide. Future behavior of the slide is difficult to predict, but possible scenarios range from continued scattered rock fall to complete rapid failure of the entire mass. Although unlikely except under very destabilizing circumstances, a worst-case, rapid failure of the entire rock slide could extend across the Merced River, damming the river and creating a reservoir. As a temporary measure, traffic has been rerouted to the opposite side of the Merced River at about the same elevation as the buried section of Highway 140. A state-of-the-art monitoring system has been installed to detect movement in the steep talus slope, movement of the main slide mass, local strong ground motion from regional earthquakes, and sudden changes in stream levels, possibly indicating damming of the river by slide material.

Energy stability of droplets and dry spots in a thin film model of hanging drops

Science.gov (United States)

Cheung, Ka-Luen; Chou, Kai-Seng

2017-10-01

The 2-D thin film equation describing the evolution of hang drops is studied. All radially symmetric steady states are classified, and their energy stability is determined. It is shown that the droplet with zero contact angle is the only global energy minimizer and the dry spot with zero contact angle is a strict local energy minimizer.

Universal method for opnimal design main structural assemblies of steel structures stationary conveyor with hanging ribbon

Directory of Open Access Journals (Sweden)

Boslovyak P.V.

2015-10-01

Full Text Available The technique and the detailed algorithm for optimal design of steel structures hospitaltion of the conveyor with hang-ing ribbon. Developed a universal objective function together with the system-limited-subject to limits of main components of steel structures of stationary conveyor with hanging ribbon.

HangOut: generating clean PSI-BLAST profiles for domains with long insertions.

Science.gov (United States)

Kim, Bong-Hyun; Cong, Qian; Grishin, Nick V

2010-06-15

Profile-based similarity search is an essential step in structure-function studies of proteins. However, inclusion of non-homologous sequence segments into a profile causes its corruption and results in false positives. Profile corruption is common in multidomain proteins, and single domains with long insertions are a significant source of errors. We developed a procedure (HangOut) that, for a single domain with specified insertion position, cleans erroneously extended PSI-BLAST alignments to generate better profiles. HangOut is implemented in Python 2.3 and runs on all Unix-compatible platforms. The source code is available under the GNU GPL license at http://prodata.swmed.edu/HangOut/. Supplementary data are available at Bioinformatics online.

SUITABILITY OF CORNEAL TISSUE FOR TRANSPLANTATION PROCURED FROM HANGING CASES

Directory of Open Access Journals (Sweden)

Rekha Gyanchand

2017-06-01

Full Text Available BACKGROUND Requirement of donor cornea is essential to target the corneal blind. The best method to procure such corneas is from any major hospitals, which has a mortuary facility. The eye donation with hanging as the cause of death is very common in a mortuary setup. Some factors that are concerning regarding corneas procured from death due to hanging is the prolonged exposure of the cornea at the time of death, the exact time of death is not known, most of the cadavers are refrigerated for investigations as these arrive at the mortuary usually at night. Due to these reasons, the corneal surgeons are hesitant to use corneas procured from death due to hanging for corneal transplantation. Analysing these corneas would contribute to a great extent to the donor cornea pool in providing sight to the corneal blind, especially as majority are young individuals who commit suicide by hanging. In this study, the donor corneas were analysed with regards to corneal epithelial defect, endothelial cell morphology and utilisation of these corneas for transplantation. The aim of the HCRP study is to analyse the effect of death due to hanging on donor cornea. 1. Corneal epithelial status. 2. Corneal endothelial cell morphology. 3. Utilisation of corneas for transplantation. MATERIALS AND METHODS Donor corneas from 22 donors who died due to hanging were procured from hospital mortuary. All the 44 corneas were transplanted. Various parameters like demography, death to enucleation time, cadaver preservation in cold storage, endothelial cell density and utilisation of cornea for transplantation were noted. Design- Retrospective study. Statistical Analysis- Descriptive statistics, Pearson and Spearman correlation and Chi-square test were used to test the hypotheses. RESULTS Out of the 44 corneas analysed, 75% of the donors were refrigerated as a part of medicolegal investigations protocol. The average DTP time was 12 hours in refrigerated group and 5 hours in non

Petrophysical, Geochemical, and Hydrological Evidence for Extensive Fracture-Mediated Fluid and Heat Transport in the Alpine Fault's Hanging-Wall Damage Zone

Science.gov (United States)

Townend, John; Sutherland, Rupert; Toy, Virginia G.; Doan, Mai-Linh; Célérier, Bernard; Massiot, Cécile; Coussens, Jamie; Jeppson, Tamara; Janku-Capova, Lucie; Remaud, Léa.; Upton, Phaedra; Schmitt, Douglas R.; Pezard, Philippe; Williams, Jack; Allen, Michael John; Baratin, Laura-May; Barth, Nicolas; Becroft, Leeza; Boese, Carolin M.; Boulton, Carolyn; Broderick, Neil; Carpenter, Brett; Chamberlain, Calum J.; Cooper, Alan; Coutts, Ashley; Cox, Simon C.; Craw, Lisa; Eccles, Jennifer D.; Faulkner, Dan; Grieve, Jason; Grochowski, Julia; Gulley, Anton; Hartog, Arthur; Henry, Gilles; Howarth, Jamie; Jacobs, Katrina; Kato, Naoki; Keys, Steven; Kirilova, Martina; Kometani, Yusuke; Langridge, Rob; Lin, Weiren; Little, Tim; Lukacs, Adrienn; Mallyon, Deirdre; Mariani, Elisabetta; Mathewson, Loren; Melosh, Ben; Menzies, Catriona; Moore, Jo; Morales, Luis; Mori, Hiroshi; Niemeijer, André; Nishikawa, Osamu; Nitsch, Olivier; Paris, Jehanne; Prior, David J.; Sauer, Katrina; Savage, Martha K.; Schleicher, Anja; Shigematsu, Norio; Taylor-Offord, Sam; Teagle, Damon; Tobin, Harold; Valdez, Robert; Weaver, Konrad; Wiersberg, Thomas; Zimmer, Martin

2017-12-01

Fault rock assemblages reflect interaction between deformation, stress, temperature, fluid, and chemical regimes on distinct spatial and temporal scales at various positions in the crust. Here we interpret measurements made in the hanging-wall of the Alpine Fault during the second stage of the Deep Fault Drilling Project (DFDP-2). We present observational evidence for extensive fracturing and high hanging-wall hydraulic conductivity (˜10-9 to 10-7 m/s, corresponding to permeability of ˜10-16 to 10-14 m2) extending several hundred meters from the fault's principal slip zone. Mud losses, gas chemistry anomalies, and petrophysical data indicate that a subset of fractures intersected by the borehole are capable of transmitting fluid volumes of several cubic meters on time scales of hours. DFDP-2 observations and other data suggest that this hydrogeologically active portion of the fault zone in the hanging-wall is several kilometers wide in the uppermost crust. This finding is consistent with numerical models of earthquake rupture and off-fault damage. We conclude that the mechanically and hydrogeologically active part of the Alpine Fault is a more dynamic and extensive feature than commonly described in models based on exhumed faults. We propose that the hydrogeologically active damage zone of the Alpine Fault and other large active faults in areas of high topographic relief can be subdivided into an inner zone in which damage is controlled principally by earthquake rupture processes and an outer zone in which damage reflects coseismic shaking, strain accumulation and release on interseismic timescales, and inherited fracturing related to exhumation.

Hanging drop cultures of human testis and testis cancer samples

DEFF Research Database (Denmark)

Jørgensen, Anne; Young, J; Nielsen, J E

2014-01-01

cultured in 'hanging drops' and effects of activin A and follistatin treatment were investigated in seminoma cultures. RESULTS: Testis fragments with normal spermatogenesis or CIS cells were cultured for 14 days with sustained proliferation of germ cells and CIS cells and without increased apoptosis....... Seminoma cultures survived 7 days, with proliferating cells detectable during the first 5 days. Activin A treatment significantly reduced KIT transcript and protein levels in seminoma cultures, thereby demonstrating a specific treatment response. CONCLUSIONS: Hanging drop cultures of human testis...

Rock Rb-Sr ages from Bananal region - Sao Paulo State, Brazil

International Nuclear Information System (INIS)

Dias Neto, C.M.; Tassinari, C.G.C.; Silva, M.E.

1996-01-01

New Rb-Sr whole rock isochron ages have been determined for the main lithological units that occur in Sao Paulo and Rio de Janeiro States. These rocks belong to Serra do Mar domain. The purpose of this work is to characterize the sequence of the geological events as well as the possible relationship between the different rocks. The geochronological data suggest that the paragneisses and the basement rocks, represented by ortho gneisses nuclei, were generated under amphibolite conditions around 700 Ma. At the same time the leucogranites were generated by partial melting processes and injected into both gneiss types. Tarditectonic granitic magmatic activities took place within ductile shear zones. One of the granites, the Getulandia granite, yielded an age of 514 Ma, falling in the range of the late Brasiliano Cycle which extended into the Middle Cambrian. (author). 9 figs., 1 tab

Adding the 'heart' to hanging drop networks for microphysiological multi-tissue experiments.

Science.gov (United States)

Rismani Yazdi, Saeed; Shadmani, Amir; Bürgel, Sebastian C; Misun, Patrick M; Hierlemann, Andreas; Frey, Olivier

2015-11-07

Microfluidic hanging-drop networks enable culturing and analysis of 3D microtissue spheroids derived from different cell types under controlled perfusion and investigating inter-tissue communication in multi-tissue formats. In this paper we introduce a compact on-chip pumping approach for flow control in hanging-drop networks. The pump includes one pneumatic chamber located directly above one of the hanging drops and uses the surface tension at the liquid-air-interface for flow actuation. Control of the pneumatic protocol provides a wide range of unidirectional pulsatile and continuous flow profiles. With the proposed concept several independent hanging-drop networks can be operated in parallel with only one single pneumatic actuation line at high fidelity. Closed-loop medium circulation between different organ models for multi-tissue formats and multiple simultaneous assays in parallel are possible. Finally, we implemented a real-time feedback control-loop of the pump actuation based on the beating of a human iPS-derived cardiac microtissue cultured in the same system. This configuration allows for simulating physiological effects on the heart and their impact on flow circulation between the organ models on chip.

Sistem Informasi Akademik pada SMA Hang Tuah Belawan

OpenAIRE

Tanjung, Dini Syahroni

2015-01-01

Informasi yang disampaikan oleh SMA HANG TUAH BELAWAN selama ini disebarkan melalui brosur dan cara yang seperti itu kurang efektif. Oleh karena itu dibuatlah sistem informasi akademik ini agar penyampaian informasinya lebih efektif dan efisien. 092406181

Reconfigurable microfluidic hanging drop network for multi-tissue interaction and analysis.

Science.gov (United States)

Frey, Olivier; Misun, Patrick M; Fluri, David A; Hengstler, Jan G; Hierlemann, Andreas

2014-06-30

Integration of multiple three-dimensional microtissues into microfluidic networks enables new insights in how different organs or tissues of an organism interact. Here, we present a platform that extends the hanging-drop technology, used for multi-cellular spheroid formation, to multifunctional complex microfluidic networks. Engineered as completely open, 'hanging' microfluidic system at the bottom of a substrate, the platform features high flexibility in microtissue arrangements and interconnections, while fabrication is simple and operation robust. Multiple spheroids of different cell types are formed in parallel on the same platform; the different tissues are then connected in physiological order for multi-tissue experiments through reconfiguration of the fluidic network. Liquid flow is precisely controlled through the hanging drops, which enable nutrient supply, substance dosage and inter-organ metabolic communication. The possibility to perform parallelized microtissue formation on the same chip that is subsequently used for complex multi-tissue experiments renders the developed platform a promising technology for 'body-on-a-chip'-related research.

Application of hanging drop technique to optimize human IgG formulations.

Science.gov (United States)

Li, Guohua; Kasha, Purna C; Late, Sameer; Banga, Ajay K

2010-01-01

The purpose of this work is to assess the hanging drop technique in screening excipients to develop optimal formulations for human immunoglobulin G (IgG). A microdrop of human IgG and test solution hanging from a cover slide and undergoing vapour diffusion was monitored by a stereomicroscope. Aqueous solutions of IgG in the presence of different pH, salt concentrations and excipients were prepared and characterized. Low concentration of either sodium/potassium phosphate or McIlvaine buffer favoured the solubility of IgG. Addition of sucrose favoured the stability of this antibody while addition of NaCl caused more aggregation. Antimicrobial preservatives were also screened and a complex effect at different buffer conditions was observed. Dynamic light scattering, differential scanning calorimetry and size exclusion chromatography studies were performed to further validate the results. In conclusion, hanging drop is a very easy and effective approach to screen protein formulations in the early stage of formulation development.

A PDMS-Based Microfluidic Hanging Drop Chip for Embryoid Body Formation.

Science.gov (United States)

Wu, Huei-Wen; Hsiao, Yi-Hsing; Chen, Chih-Chen; Yet, Shaw-Fang; Hsu, Chia-Hsien

2016-07-06

The conventional hanging drop technique is the most widely used method for embryoid body (EB) formation. However, this method is labor intensive and limited by the difficulty in exchanging the medium. Here, we report a microfluidic chip-based approach for high-throughput formation of EBs. The device consists of microfluidic channels with 6 × 12 opening wells in PDMS supported by a glass substrate. The PDMS channels were fabricated by replicating polydimethyl-siloxane (PDMS) from SU-8 mold. The droplet formation in the chip was tested with different hydrostatic pressures to obtain optimal operation pressures for the wells with 1000 μm diameter openings. The droplets formed at the opening wells were used to culture mouse embryonic stem cells which could subsequently developed into EBs in the hanging droplets. This device also allows for medium exchange of the hanging droplets making it possible to perform immunochemistry staining and characterize EBs on chip.

A PDMS-Based Microfluidic Hanging Drop Chip for Embryoid Body Formation

Directory of Open Access Journals (Sweden)

Huei-Wen Wu

2016-07-01

Full Text Available The conventional hanging drop technique is the most widely used method for embryoid body (EB formation. However, this method is labor intensive and limited by the difficulty in exchanging the medium. Here, we report a microfluidic chip-based approach for high-throughput formation of EBs. The device consists of microfluidic channels with 6 × 12 opening wells in PDMS supported by a glass substrate. The PDMS channels were fabricated by replicating polydimethyl-siloxane (PDMS from SU-8 mold. The droplet formation in the chip was tested with different hydrostatic pressures to obtain optimal operation pressures for the wells with 1000 μm diameter openings. The droplets formed at the opening wells were used to culture mouse embryonic stem cells which could subsequently developed into EBs in the hanging droplets. This device also allows for medium exchange of the hanging droplets making it possible to perform immunochemistry staining and characterize EBs on chip.

Structural analysis of hanging wall and footwall blocks within the Río Guanajibo fold-and-thrust belt in Southwest Puerto Rico

Science.gov (United States)

Laó-Dávila, Daniel A.; Llerandi-Román, Pablo A.

2017-01-01

The Río Guanajibo fold-and-thrust belt (RGFT), composed of Cretaceous serpentinite and volcano-sedimentary rocks, represents the deformation front of a contractional event in SW Puerto Rico during the Paleogene. Previous studies inferred structural and stratigraphic relationships from poorly exposed outcrops. New road cuts exposed the Yauco (YF) and El Rayo Formations (ERF) providing insights on the deformation of the hanging wall and footwall. We described the nature and orientation of faults and folds and analyzed the kinematic indicators to characterize the deformation. The YF occurs in the hanging wall and shows a sequence of folded, medium-bedded mudstone and thinly bedded shale and sandstone. Major folds strike NW-SE and are gentle with steeply inclined axial planes and sub-horizontal fold axes. Minor folds are open with moderately inclined axial planes and gently to moderately inclined SE-plunging fold axes. NW-SE striking reverse and thrust faults cut layers and show movement to the SW. Steep left-lateral faults strike NW-SE and NE-SW, and smaller right-lateral strike-slip faults strike NNE-SSW. At the footwall, the ERF consists of bioclastic limestone and polymictic orthoconglomerates and paraconglomerates. Reverse and strike-slip faults cut along lithological contacts. Results suggest that the hanging wall and footwall accommodated strain along preexisting weaknesses, which are dependent on lithology and sedimentary structures. The kinematic analysis suggests that shortening in the NE-SW direction was partitioned between folding and interlayer shortening, accommodated by flexural slip, and reverse and left-lateral faults that resulted from contraction. The RGFT represents the Paleogene back arc deformation of a bivergent thrust system.

Hydrology of some deep mines in Precambrian rocks

International Nuclear Information System (INIS)

Yardley, D.H.

1975-10-01

A number of underground mines were investigated during the summer of 1975. All of them are in Precambrian rocks of the Lake Superior region. They represent a variety of geologic settings. The purpose of the investigations was to make a preliminary study of the dryness, or lack of dryness of these rocks at depth. In other words, to see if water was entering the deeper workings through the unmined rock by some means such as fracture or fault zones, joints or permeable zones. Water entering through old mine workings extending to, or very near to the surface, or from the drilling equipment, was of interest only insofar as it might mask any water whose source was through the hanging or footwall rocks. No evidence of running, seeping or moving water was seen or reported at depths exceeding 3,000 feet. At depths of 3,000 feet or less, water seepages do occur in some of the mines, usually in minor quantities but increased amounts occur as depth becomes less. Others are dry at 2,000 feet of depth. Rock movements associated with extensive mining should increase the local secondary permeability of the rocks adjoining the mined out zones. Also most ore bodies are located where there has been a more than average amount of faulting, fracturing, and folding during the geologic past. They tend to cluster along crustal flows. In general, Precambrian rocks of similar geology, to those seen, well away from zones that have been disturbed by extensive deep mining, and well away from the zones of more intense geologic activity ought to be even less permeable than their equivalents in a mining district

Hydrology of some deep mines in Precambrian rocks

Energy Technology Data Exchange (ETDEWEB)

Yardley, D.H.

1975-10-01

A number of underground mines were investigated during the summer of 1975. All of them are in Precambrian rocks of the Lake Superior region. They represent a variety of geologic settings. The purpose of the investigations was to make a preliminary study of the dryness, or lack of dryness of these rocks at depth. In other words, to see if water was entering the deeper workings through the unmined rock by some means such as fracture or fault zones, joints or permeable zones. Water entering through old mine workings extending to, or very near to the surface, or from the drilling equipment, was of interest only insofar as it might mask any water whose source was through the hanging or footwall rocks. No evidence of running, seeping or moving water was seen or reported at depths exceeding 3,000 feet. At depths of 3,000 feet or less, water seepages do occur in some of the mines, usually in minor quantities but increased amounts occur as depth becomes less. Others are dry at 2,000 feet of depth. Rock movements associated with extensive mining should increase the local secondary permeability of the rocks adjoining the mined out zones. Also most ore bodies are located where there has been a more than average amount of faulting, fracturing, and folding during the geologic past. They tend to cluster along crustal flows. In general, Precambrian rocks of similar geology, to those seen, well away from zones that have been disturbed by extensive deep mining, and well away from the zones of more intense geologic activity ought to be even less permeable than their equivalents in a mining district.

Mineral and rock chemistry of Mata da Corda Kamafugitic Rocks (Minas Gerais State, Brazil)

International Nuclear Information System (INIS)

Albuquerque Sgarbi, Patricia B. de; Valenca, Joel G.

1995-01-01

The volcanic rocks of the Mata da Corda Formation (Upper Cretaceous) in Minas Gerais, Brazil, are mafic potassic to ultra potassic rocks of kamafugitic affinity containing essentially clinopyroxenes, perovskite, magnetite and occasionally olivine, phlogopite, melilite pseudomorphs and apatite. The felsic phases are kalsilite and/or leucite pseudomorphs. The rocks are classified as mafitites, leucitites and kalsilitites. The analysis of the available data of the rocks studied, based on the relevant aspects of the main proposals for the classification of alkaline mafic to ultramafic potassic rocks leads to the conclusion that Sahama's (1974) proposal to divide potassium rich alkaline rocks in two large families is the one to which the Mata da Corda rocks adapt best. According to this and the data in the literature on the mineralogy and mineral and rock chemistries of the other similar occurrences, these rocks may be interpreted as alkaline potassic to ultra potassic rocks of hamafugitic affinity. 11 figs., 5 tabs

A hanging drop culture method to study terminal erythroid differentiation.

Science.gov (United States)

Gutiérrez, Laura; Lindeboom, Fokke; Ferreira, Rita; Drissen, Roy; Grosveld, Frank; Whyatt, David; Philipsen, Sjaak

2005-10-01

To design a culture method allowing the quantitative and qualitative analysis of terminal erythroid differentiation. Primary erythroid progenitors derived either from mouse tissues or from human umbilical cord blood were differentiated using hanging drop cultures and compared to methylcellulose cultures. Cultured cells were analyzed by FACS to assess differentiation. We describe a practical culture method by adapting the previously described hanging drop culture system to conditions allowing terminal differentiation of primary erythroid progenitors. Using minimal volumes of media and small numbers of cells, we obtained quantitative terminal erythroid differentiation within two days of culture in the case of murine cells and 4 days in the case of human cells. The established methods for ex vivo culture of primary erythroid progenitors, such as methylcellulose-based burst-forming unit-erythroid (BFU-E) and colony-forming unit-erythroid (CFU-E) assays, allow the detection of committed erythroid progenitors but are of limited value to study terminal erythroid differentiation. We show that the application of hanging drop cultures is a practical alternative that, in combination with clonogenic assays, enables a comprehensive assessment of the behavior of primary erythroid cells ex vivo in the context of genetic and drug-induced perturbations.

Prediction of slope stability based on numerical modeling of stress–strain state of rocks

Science.gov (United States)

Kozhogulov Nifadyev, KCh, VI; Usmanov, SF

2018-03-01

The paper presents the developed technique for the estimation of rock mass stability based on the finite element modeling of stress–strain state of rocks. The modeling results on the pit wall landslide as a flow of particles along a sloped surface are described.

Wireless Orbiter Hang-Angle Inclinometer System

Science.gov (United States)

Lucena, Angel; Perotti, Jose; Green, Eric; Byon, Jonathan; Burns, Bradley; Mata, Carlos; Randazzo, John; Blalock, Norman

2011-01-01

A document describes a system to reliably gather the hang-angle inclination of the orbiter. The system comprises a wireless handheld master station (which contains the main station software) and a wireless remote station (which contains the inclinometer sensors, the RF transceivers, and the remote station software). The remote station is designed to provide redundancy to the system. It includes two RF transceivers, two power-management boards, and four inclinometer sensors.

Characterization and reproducibility of HepG2 hanging drop spheroids toxicology in vitro.

Science.gov (United States)

Hurrell, Tracey; Ellero, Andrea Antonio; Masso, Zelie Flavienne; Cromarty, Allan Duncan

2018-02-21

Hepatotoxicity remains a major challenge in drug development despite preclinical toxicity screening using hepatocytes of human origin. To overcome some limitations of reproducing the hepatic phenotype, more structurally and functionally authentic cultures in vitro can be introduced by growing cells in 3D spheroid cultures. Characterisation and reproducibility of HepG2 spheroid cultures using a high-throughput hanging drop technique was performed and features contributing to potential phenotypic variation highlighted. Cultured HepG2 cells were seeded into Perfecta 3D® 96-well hanging drop plates and assessed over time for morphology, viability, cell cycle distribution, protein content and protein-mass profiles. Divergent aspects which were assessed included cell stocks, seeding density, volume of culture medium and use of extracellular matrix additives. Hanging drops are advantageous due to no complex culture matrix being present, enabling background free extractions for downstream experimentation. Varying characteristics were observed across cell stocks and batches, seeding density, culture medium volume and extracellular matrix when using immortalized HepG2 cells. These factors contribute to wide-ranging cellular responses and highlights concerns with respect to generating a reproducible phenotype in HepG2 hanging drop spheroids. Copyright © 2018 Elsevier Ltd. All rights reserved.

Adding the ‘heart’ to hanging drop networks for microphysiological multi-tissue experiments†

Science.gov (United States)

Yazdi, Saeed Rismani; Shadmani, Amir; Bürgel, Sebastian C.; Misun, Patrick M.; Hierlemann, Andreas; Frey, Olivier

2017-01-01

Microfluidic hanging-drop networks enable culturing and analysis of 3D microtissue spheroids derived from different cell types under controlled perfusion and investigating inter-tissue communication in multi-tissue formats. In this paper we introduce a compact on-chip pumping approach for flow control in hanging-drop networks. The pump includes one pneumatic chamber located directly above one of the hanging drops and uses the surface tension at the liquid–air-interface for flow actuation. Control of the pneumatic protocol provides a wide range of unidirectional pulsatile and continuous flow profiles. With the proposed concept several independent hanging-drop networks can be operated in parallel with only one single pneumatic actuation line at high fidelity. Closed-loop medium circulation between different organ models for multi-tissue formats and multiple simultaneous assays in parallel are possible. Finally, we implemented a real-time feedback control-loop of the pump actuation based on the beating of a human iPS-derived cardiac microtissue cultured in the same system. This configuration allows for simulating physiological effects on the heart and their impact on flow circulation between the organ models on chip. PMID:26401602

Simulation of hanging dams downstream of Ossauskoski power plant

Energy Technology Data Exchange (ETDEWEB)

Aaltonen, J.; Huokuna, M. [Finnish Environment Inst., Helsinki (Finland); Severinkangas, K.; Talvensaari, M. [Kemijoki Oy, Rovaniemi (Finland)

2008-07-01

Sixteen power plants have been constructed along Finland's Kemijoki River for hydroelectric power production. The Ossauskoski facility has recently undergone major renovations and upgrade, making it the sixth largest hydroelectric power plant in Finland, with a new capacity of 124 MW and an annual energy output of 501 GWh. The increase in power output and discharge may cause changes in ice conditions downstream of the power plant. The section of the river is already subjected to frazil ice problems and hanging dam formation. Discharges and adverse effects of frazil ice phenomena are likely to increase due to climate change, resulting in harm for hydropower production and the environment, particularly in flow regulated rivers where winter discharges are higher than natural discharges. As such, a study was launched to investigate a dredge plan suggested by by the electric utility Kemijoki Oy. The project involved mapping the river bed topography to identify the location and extent of hanging dams. A sounding device and ground penetrating radar was used to find the thaw regions in the ice cover. The JJT numerical river ice model was effectively used to study the effect of hanging dams on water levels. However, the ice bridging phenomena was not modelled in a reliable way by the JJT model and will be modelled in the future using the CRISSP2D numerical model. 5 refs., 11 figs.

Toxicology findings in cases of hanging in the City and County of San Francisco over the 3-year period from 2011 to 2013.

Science.gov (United States)

San Nicolas, A C; Lemos, N P

2015-10-01

, their possible state of impairment, including the possibility of a staged suicide if the decedent was too impaired to perform a self-hanging. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Experimental research data on stress state of salt rock mass around an underground excavation

Science.gov (United States)

Baryshnikov, VD; Baryshnikov, DV

2018-03-01

The paper presents the experimental stress state data obtained in surrounding salt rock mass around an excavation in Mir Mine, ALROSA. The deformation characteristics and the values of stresses in the adjacent rock mass are determined. Using the method of drilling a pair of parallel holes in a stressed area, the authors construct linear relationship for the radial displacements of the stress measurement hole boundaries under the short-term loading of the perturbing hole. The resultant elasticity moduli of rocks are comparable with the laboratory core test data. Pre-estimates of actual stresses point at the presence of a plasticity zone in the vicinity of the underground excavation. The stress state behavior at a distance from the excavation boundary disagrees with the Dinnik–Geim hypothesis.

Implementasi Kebijakan Kawasan Tanpa Rokok (KTR) pada Mahasiswa di Lingkungan Sekolah Tinggi Ilmu Kesehatan Hang Tuah Pekanbaru

OpenAIRE

Reno Renaldi

2014-01-01

Sekolah Tinggi Ilmu Kesehatan (STIKes) Hang Tuah Pekanbaru sebagai tempat pelaksanaan proses belajar mengajar bagi mahasiswa sekaligus tempat kerja bagi karyawannya,  yang mana seyogyanya tempat tersebut menjadi tempat Kawasan Tanpa Rokok berdasarkan Undang-undang kesehatan.Oleh karena itu sejak tahun2011STIKes Hang Tuah telah mengeluarkan kebijakan dalam bentuk surat edaran dengan nomor surat No/09/STIKes-HTP/IX/2011/289/mengenai Kawasan Tanpa Rokok di lingkungan STIKes Hang Tuah Pekanbaru.P...

Death by hanging: implications for prevention of an important method of youth suicide.

Science.gov (United States)

Kosky, R J; Dundas, P

2000-10-01

The aim of this study was to identify factors associated with deaths by hanging among young people in Queensland, Australia. An examination of coroner's reports for all deaths by hanging of people under 25 years of age that occurred in Queensland in the years 1995 and 1996. All cases were recorded as suicides. Most were males and a quarter were indigenous persons. Half the deaths occurred in regional or rural areas. Unemployment, the experience of personal loss, psychiatric illness and alcohol use were possible precipitating agents. Early warning signs were the onset of uncharacteristic behaviours and threats of suicide. The private nature of hanging means that there are rarely opportunities to prevent it in the period immediately before the fatal event. Earlier interventions will have to be considered. To prevent hanging as a means of suicide, we need to understand more about the difficulties experienced by some young men who are living in rural areas. We need more information about the cultural problems experienced by indigenous youths in their teenage years. Young people in the justice system may need personal support. There is a pressing need to determine if young people, especially in rural areas, have adequate access to the professional expertise needed to diagnose and treat mental disorders.

CASE REPORT OF SUCCESSFUL RESUSCITATION OF A CASE O F SUICIDAL HANGING

OpenAIRE

Yanki D.

2013-01-01

ABSTRACT: In Sikkim, the rate of suicide has been on the rise since the last 10 years. Suicidal hanging as method of ending life is a major concern among school children. It is very rare that the victims are brought on time for successful resuscit ation in Sikkim. Suicide by hanging is probably the most easy way to go about taking one’s own life , as the means to do it are easily available and uncomplicated and, brutally efficient in most case s . This is a case ...

Numerical analysis of the effects induced by normal faults and dip angles on rock bursts

Science.gov (United States)

Jiang, Lishuai; Wang, Pu; Zhang, Peipeng; Zheng, Pengqiang; Xu, Bin

2017-10-01

The study of mining effects under the influences of a normal fault and its dip angle is significant for the prediction and prevention of rock bursts. Based on the geological conditions of panel 2301N in a coalmine, the evolution laws of the strata behaviors of the working face affected by a fault and the instability of the fault induced by mining operations with the working face of the footwall and hanging wall advancing towards a normal fault are studied using UDEC numerical simulation. The mechanism that induces rock burst is revealed, and the influence characteristics of the fault dip angle are analyzed. The results of the numerical simulation are verified by conducting a case study regarding the microseismic events. The results of this study serve as a reference for the prediction of rock bursts and their classification into hazardous areas under similar conditions.

Optimal Population of Embryonic Stem Cells in "Hanging Drop" Culture for in-vitro Differentiation to Cardiac Myocytes

OpenAIRE

MIWA, Keiko; LEE, Jong-Kook; HIDAKA, Kyoko; SHI, Rong-qian; MORISAKI, Takayuki; KODAMA, Itsuo

2002-01-01

Pluripotent embryonic stem (ES) cells differentiate to cardiac myocytes in vitro by many other previous reports demonstrated "hanging-drop" method. In this study, the number of ES cells in each hanging-drop plays an important role in the cultivation of cardiac myocytes. We examined the optimal hanging-drop size to obtain embryonic stem cell-derived cardiac cells (ESCMs) in vitro using specific labeled mouse ES cells (hCGP7) which were stably transfected with the enhanced green fluorescent pro...

Common Cause Case Study: An Estimated Probability of Four Solid Rocket Booster Hold-Down Post Stud Hang-ups

Science.gov (United States)

Cross, Robert

2005-01-01

Until Solid Rocket Motor ignition, the Space Shuttle is mated to the Mobil Launch Platform in part via eight (8) Solid Rocket Booster (SRB) hold-down bolts. The bolts are fractured using redundant pyrotechnics, and are designed to drop through a hold-down post on the Mobile Launch Platform before the Space Shuttle begins movement. The Space Shuttle program has experienced numerous failures where a bolt has hung up. That is, it did not clear the hold-down post before liftoff and was caught by the SRBs. This places an additional structural load on the vehicle that was not included in the original certification requirements. The Space Shuttle is currently being certified to withstand the loads induced by up to three (3) of eight (8) SRB hold-down experiencing a "hang-up". The results of loads analyses performed for (4) stud hang-ups indicate that the internal vehicle loads exceed current structural certification limits at several locations. To determine the risk to the vehicle from four (4) stud hang-ups, the likelihood of the scenario occurring must first be evaluated. Prior to the analysis discussed in this paper, the likelihood of occurrence had been estimated assuming that the stud hang-ups were completely independent events. That is, it was assumed that no common causes or factors existed between the individual stud hang-up events. A review of the data associated with the hang-up events, showed that a common factor (timing skew) was present. This paper summarizes a revised likelihood evaluation performed for the four (4) stud hang-ups case considering that there are common factors associated with the stud hang-ups. The results show that explicitly (i.e. not using standard common cause methodologies such as beta factor or Multiple Greek Letter modeling) taking into account the common factor of timing skew results in an increase in the estimated likelihood of four (4) stud hang-ups of an order of magnitude over the independent failure case.

Anatomical basis of the liver hanging maneuver.

Science.gov (United States)

Trotovsek, Blaz; Belghiti, Jacques; Gadzijev, Eldar M; Ravnik, Dean; Hribernik, Marija

2005-01-01

The anterior approach to right hepatectomy using the liver hanging maneuver without liver mobilization claims to be anatomically evaluated. During this procedure a 4 to 6-cm blind dissection between the inferior vena cava and the liver is performed. Short subhepatic veins, entering the inferior vena cava could be torn and a hemorrhage, difficult to control, could occur. On 100 corrosive casts of livers the anterior surface of the inferior vena cava was studied to evaluate the position, diameter and draining area of short subhepatic veins and inferior right hepatic vein. The width of the narrowest point on the planned route of blind dissection was determined. The average value of the narrowest point on the planned route of blind dissection was 8.7+/-2.3mm (range 2-15mm). The ideal angle of dissection being 0 degrees was found in 93% of cases. In 7% we found the angle of 5 degrees toward the right border of inferior vena cava to be the better choice. Our results show that liver hanging maneuver is a safe procedure. With the dissection in the proposed route the risk of disrupting short subhepatic veins is low (7%).

Candidate sites for future hot-dry-rock development in the United States

Energy Technology Data Exchange (ETDEWEB)

Goff, F.; Decker, E.R.

1982-12-01

Generalized geologic and other data are tabulated for 24 potential hot dry rock (HDR) sites in the contiguous United States. The data show that HDR resources occur in many geologic and tectonic settings. Potential reservoir rocks at each prospect are described and each system is cateogrized accoridng to inferred heat sources. The Fenton Hill area in New Mexico is discussed in detail because this region may be considered ideal for HDR development. Three other prospectively valuable localities are described: The Geysers-Clear lake region in California, the Roosevelt Hot Springs area in Utah, and the White Mountains region in New Hampshire. These areas are singled out to illustrate the roles of significantly different geology and geophysics, reservoir rocks, and reservoir heat contents in possible HDR developments.

High Temperature Versus Geomechanical Parameters of Selected Rocks – The Present State of Research

Directory of Open Access Journals (Sweden)

Anna Sygała

2013-01-01

Full Text Available This paper presents the current state of knowledge concerning the examination of the impact of increased temperatures on changes of geomechanical properties of rocks. Based on historical data, the shape of stress–strain characteristics that illustrate the process of the destruction of rock samples as a result of load impact under uniaxial compression in a testing machine, were discussed. The results from the studies on changes in the basic strength and elasticity parameters of rocks, such as the compressive strength and Young’s modulus were compared. On their basis, it was found that temperature has a significant effect on the change of geomechanical properties of rocks. The nature of these changes also depends on other factors (apart from temperature. They are, among others: the mineral composition of rock, the porosity and density. The research analysis showed that changes in the rock by heating it at various temperatures and then uniaxially loading it in a testing machine, are different for different rock types. Most of the important processes that cause changes in the values of the strength parameters of the examined rocks occured in the temperature range of 400 to 600 °C.

Validation of choice and determination of geotechnology parameters with regard to stress–strain state of rocks

Science.gov (United States)

Freidin, AM; Neverov, SA; Neverov, AA; Konurin, AI

2018-03-01

The paper illustrates efficiency and reliability of types of rock mass stress state conditioned by geological and structural features of rocks in design, selection and validation of geotechnology parameters. The authors of the paper present calculation of stresses in rock mass under sublevel stoping depending on the type of the geosphere and on the depth of the ore body occurrence.

A novel fabrication technique for free-hanging homogeneous polymeric cantilever waveguides

International Nuclear Information System (INIS)

Nordström, Maria; Hübner, Jörg; Boisen, Anja; Calleja, Montserrat

2008-01-01

We present a novel bonding technique developed for the fabrication of a cantilever-based biosensing system with integrated optical read-out. The read-out mechanism is based on single-mode waveguides fabricated monolithically in SU-8. For optimal operation of the read-out mode, the cantilever waveguides should be homogenous and this bonding technique ensures free-hanging cantilevers that are surrounded by the same material for bottom and top claddings. The bonding step is necessary because SU-8 is a negative resist where free-hanging structures cannot be fabricated directly. This paper gives details on the processing aspects and the parameters of the fabrication steps

Perilaku Seks Pranikah pada Mahasiswa STIKes Hang Tuah Pekanbaru

Directory of Open Access Journals (Sweden)

Novita Rany

2012-11-01

Full Text Available Hasil penelitian PKBI (Persatuan Keluarga Berencana Indonesia – Riau tahun 2009 bahwa 38,75 % pria sudah melakukan hubungan seks pranikah sedangkan wanita 16,98 %. Penelitian ini menggunakan metode kualitatif. Subjek penelitian adalah mahasiswa STIKes Hang Tuah Pekanbaru, informan kunci merupakan dosen bagian kemahasiswaan, orang tua, ibu kos dan teman dekat. Dari penelitian ini diperoleh bahwa Perilaku seksual dibagi kedalam yang tidak berisiko (mulai dari ngobrol dan pegangan tangan saja, dan yang berisiko (dari ciuman sampai dengan berhubungan intim. Dari hasil penelitian diketahui 7 informan yang berisiko dan 9 lainnya tidak berisiko. Hampir separuh (7 dari 16 informan berperilaku seksual yang berisiko dan beberapa diantaranya pernah melakukan hubungan seksual pra nikah. Ada kecenderungan hubungan antara pengetahuan, sikap, persepsi, teman sebaya dan peran keluarga dalam mengawasi pergaulan anaknya terhadap perilaku seks berisiko. Saran bagi STIKes Hang Tuah dan Dinas Kesehatan agar dapat memasukan pendidikan seks kedalam kurikulum

384 hanging drop arrays give excellent Z-factors and allow versatile formation of co-culture spheroids.

Science.gov (United States)

Hsiao, Amy Y; Tung, Yi-Chung; Qu, Xianggui; Patel, Lalit R; Pienta, Kenneth J; Takayama, Shuichi

2012-05-01

We previously reported the development of a simple, user-friendly, and versatile 384 hanging drop array plate for 3D spheroid culture and the importance of utilizing 3D cellular models in anti-cancer drug sensitivity testing. The 384 hanging drop array plate allows for high-throughput capabilities and offers significant improvements over existing 3D spheroid culture methods. To allow for practical 3D cell-based high-throughput screening and enable broader use of the plate, we characterize the robustness of the 384 hanging drop array plate in terms of assay performance and demonstrate the versatility of the plate. We find that the 384 hanging drop array plate performance is robust in fluorescence- and colorimetric-based assays through Z-factor calculations. Finally, we demonstrate different plate capabilities and applications, including: spheroid transfer and retrieval for Janus spheroid formation, sequential addition of cells for concentric layer patterning of different cell types, and culture of a wide variety of cell types. Copyright © 2011 Wiley Periodicals, Inc.

Death by hanging while watching violent pornographic videos on the Internet - suicide or accidental autoerotic death?

Science.gov (United States)

Vennemann, B; Pollak, S

2006-03-01

In deaths by hanging, it may sometimes be difficult to differentiate between autoerotic accident and suicide. Our report deals with a 30-year-old man who was found hanged in the living room of his flat. The deceased was wearing headphones connected to a PC. Within the deceased's view was a computer screen showing the last picture of a video file downloaded from the Internet with the head of an unclothed, allegedly hanged female. The deceased's left hand was inside his trousers in the genital region. The autopsy did not only show findings typical for hanging, but also advanced sarcoidosis, which was known to the victim. Although this basic illness could have been a possible motive for suicide, the circumstances in the presented case pointed more in the direction of an accidental autoerotic death. As far as we know, this is the first description of a death during autoerotic activity in which sexual stimulation was achieved by watching a video file downloaded from the Internet.

Rocks age and metamorphic occurrence from the southeastern part of Sao Paulo State and their crustal evaluation

International Nuclear Information System (INIS)

Tassinari, C.C.G.

1988-01-01

Pb-Pb and Rb-Sr whole rock isotope systematics and U-Pb on zircons method analyses are reported for rocks from the southeastern part of Sao Paulo state Brazil. The isotopic studies on granitic intrusions, orthogneissic rocks and migmatitic terranes, in this area, provides an important indication of the age and nature of the continental crust. (author) [pt

Applying the information received in the process of drilling for the estimation of the state of rocks

Energy Technology Data Exchange (ETDEWEB)

Denissov, N Ya; Paushkin, G A; Zaytzev, A S

1966-01-01

In estimating rock foundations for construction, data on the condition of the degree of jointing and weathering are of major importance. For estimating the condition, (in particular, data on core recovery and the speed of boring) drill holes are used. In this paper it is shown that the data on core recovery during the boring of drill holes in regions with complex tectonics can give a wrong idea about the state of rock. However, data on the speed of clean boring may prove to be useful. In some cases low core recovery and its large crushing are caused by the influence of the heterogeneity of rock composition as well as by the influence of changes in the stressed state of rock during boring. The data on the speed of clean boring can be used in engineering geological practice to estimate the intensity and character of spreading rock jointing and to determine the depth of weathering penetration.

Culturing muscle fibres in hanging drop: a novel approach to solve an old problem.

Science.gov (United States)

Archacka, Karolina; Pozzobon, Michela; Repele, Andrea; Rossi, Carlo Alberto; Campanella, Michelangelo; De Coppi, Paolo

2014-02-01

The satellite cells (SCs) associated with muscle fibres play a key role in postnatal growth and regeneration of skeletal muscle. Commonly used methods of isolation and in vitro culture of SCs lead to the mixture of their subpopulations that exist within muscle. To solve this problem, we used the well established technique, the hanging drop system, to culture SCs in a three-dimensional environment and thus, to monitor them in their original niche. Using hanging drop technique, we were able to culture SCs associated with the fibre at least for 9 days with one transfer of fibres to the fresh drops. In comparison, in the classical method of myofibres culture, that is, on the dishes coated with Matrigel, SCs leave the fibres within 3 days after the isolation. Cells cultured in both systems differed in expression of Pax7 and MyoD. While almost all cells cultured in adhesion system expressed MyoD before the fifth day of the culture, the majority of SCs cultured in hanging drop still maintained expression of Pax7 and were not characterised by the presence of MyoD. Among the cells cultured with single myofibre for up to 9 days, we identified two different subclones of SCs: low proliferative clone and high proliferative clone, which differed in proliferation rate and membrane potential. The hanging drop enables the myofibres to be kept in suspension for at least 9 days, and thus, allows SCs and their niche to interact each other for prolonged time. In a consequence, SCs cultured in hanging drop maintain expression of Pax7 while those cultured in a traditional adhesion culture, that is, devoid of signals from the original niche, activate and preferentially undergo differentiation as manifested by expression of MyoD. Thus, the innovative method of SCs culturing in the hanging drop system may serve as a useful tool to study the fate of different subpopulations of these cells in their anatomical location and to determine reciprocal interactions between them and their niche. �

Some evidence of uranium in volcanic feldspar rocks in the state of Sonora

Energy Technology Data Exchange (ETDEWEB)

Marquina M, O. E. [Uranio Mexicano, Mexico City

1983-05-15

Description is given of four projects of exploration and survey for uranium associated with tertiary volcanic feldspar rocks importantly dispersed in the State of Sonora and being carried out by Uranium Mexicano.

An optimized protocol for handling and processing fragile acini cultured with the hanging drop technique.

Science.gov (United States)

Snyman, Celia; Elliott, Edith

2011-12-15

The hanging drop three-dimensional culture technique allows cultivation of functional three-dimensional mammary constructs without exogenous extracellular matrix. The fragile acini are, however, difficult to preserve during processing steps for advanced microscopic investigation. We describe adaptations to the protocol for handling of hanging drop cultures to include investigation using confocal, scanning, and electron microscopy, with minimal loss of cell culture components. Copyright © 2011 Elsevier Inc. All rights reserved.

Stress–strain state of adjacent rock mass under slice mining of steeply dipping ore bodies

Science.gov (United States)

Baryshnikov, VD; Gakhova, LN

2018-03-01

Under analysis is the stress state of rock mass surrounding stopes in the initial cutting layer displaced in plan relative to the above-lying extracted layer in the overcut rock mass. The authors determine the boundaries of the post-limiting deformation zones during stoping advance using the Mohr–Coulomb criterion. The sequence of stoping to ensure better support conditions is proposed.

Water resources and effects of potential surface coal mining on dissolved solids in Hanging Woman Creek basin, southeastern Montana

Science.gov (United States)

Cannon, M.R.

1989-01-01

Groundwater resources of the Hanging Woman Creek basin, Montana include Holocene and Pleistocene alluvial aquifers and sandstone , coal, and clinker aquifers in the Paleocene Fort Union Formation. Surface water resources are composed of Hanging Woman Creek, its tributaries, and small stock ponds. Dissolved-solids concentrations in groundwater ranged from 200 to 11,00 mg/L. Generally, concentrations were largest in alluvial aquifers and smallest in clinker aquifers. Near its mouth, Hanging Woman Creek had a median concentration of about 1,800 mg/L. Mining of the 20-foot to 35-foot-thick Anderson coal bed and 3-foot to 16-foot thick Dietz coal bed could increase dissolved-solids concentrations in shallow aquifers and in Hanging Woman Creek because of leaching of soluble minerals from mine spoils. Analysis of saturated-paste extracts from 158 overburden samples indicated that water moving through mine spoils would have a median increase in dissolved-solids concentration of about 3,700 mg/L, resulting in an additional dissolved-solids load to Hanging Woman Creek of about 3.0 tons/day. Hanging Woman Creek near Birney could have an annual post-mining dissolved-solids load of 3,415 tons at median discharge, a 47% increase from pre-mining conditions load. Post-mining concentrations of dissolved solids, at median discharge, could range from 2,380 mg/L in March to 3,940 mg/L in August, compared to mean pre-mining concentrations that ranged from 1,700 mg/L in July, November, and December to 2,060 mg/L in May. Post-mining concentrations and loads in Hanging Woman Creek would be smaller if a smaller area were mined. (USGS)

Stressed-deformed state of mountain rocks in elastic stage and between elasticity

Directory of Open Access Journals (Sweden)

Samedov A.M.

2017-12-01

Full Text Available The problems of the stress-strain state of rocks in the elastic stage and beyond the elastic limits, and the ways of schematizing the tension and compression diagrams were reviewed in the article. To simplify calculations outside the elastic range, the tension (compression diagrams are usually schematized, i.e. are replaced by curved smooth lines having a fairly simple mathematical expression and at the same time well coinciding with the experimentally obtained diagrams. When diagram is to be schematized, it is necessary to take a constant temperature of superheated water steam if a rock test is planned in a relaxed form. Note that when the diagram is schematizing, the difference between the limits of proportionality and fluidity is erased. This allows the limit of proportionality to be considered the limit of fluidity. Schematicization can be carried out in the area where the tensile strength (compression is planned to be destroyed with the established weakening of rocks by exposure to water steam or chemical reagents. Samples of rocks in natural form were tested and weakened by means of superheated water steam (220 °C and more and chemical reagents for tension and compression. The data are obtained, the diagrams of deformation are constructed and schematized in the elastic stage and beyond the elastic limit. Based on the schematic diagrams of deformation, the components of stress and strain were composed in the elastic stage and beyond the elastic limit. It is established in the publication that rocks under compression and stretching deform, both within the elastic stage, and beyond the limits of elasticity. This could be seen when the samples, both in natural and in weakened state, with superheated water steam (more than 220 °C or chemical reagents were tested. In their natural form, they are mainly deformed within the elastic stage and are destroyed as a brittle material, and in a weakened form they can deform beyond the elastic stage and

Unusual planned complex suicide committed with a muzzle-loading pistol in combination with subsequent hanging.

Science.gov (United States)

Ondruschka, Benjamin; Morgenthal, Sylvia; Dreβler, Jan; Bayer, Ronny

2016-11-01

In Germany, suicides by firearms are not very common in contrast to deaths by hanging and intoxications. The use of historical muzzle-loading firearms in the context of suicides is a rarity. Contact shots from muzzle loaders cause an unusual wound morphology with extensive soot soiling. We report the case of a 59-year-old man, who committed a planned complex suicide by shooting into his mouth with a replica percussion gun in combination with hanging. The gunshot injury showed strong explosive effects in the oral cavity with fractures of the facial bones and the skull associated with cerebral evisceration (so-called Krönlein shot). Due to the special constellation of the case with hanging immediately after the shot, external bleeding from the head injuries was only moderate. Therefore, the head injuries could be assessed and partially reconstructed already at the scene.

A tree branch instead of a ligature: an unusual accidental hanging.

Science.gov (United States)

Vadysinghe, Amal Nishantha; Sivasubramanium, Murugupillai; Jayasooriya, Rankothge Pemasiri

2017-12-01

A unique case of accidental hanging due to compression of the neck of an adult by the branches of a coffee tree is reported. The decedent was a 42-year-old male who was found dead in a semi prone position on a slope. His neck was lodged in a wedge formed by two branches of a coffee tree, with his legs angled downwards on the slope. Autopsy revealed two friction abrasions located horizontally on either side of the front of the neck, just above the larynx. The findings were compatible with compression of the neck by the branches of the tree, with the body weight of the decedent contributing to compression. Subsequent complete autopsy examination confirmed the cause of death as hanging. Following an inquest the death was ruled to be accidental.

A new method for determining the uranium and thorium distribution in volcanic rock samples using solid state nuclear track detectors

International Nuclear Information System (INIS)

Misdaq, M.A.; Bakhchi, A.; Ktata, A.; Koutit, A.; Lamine, J.; Ait nouh, F.; Oufni, L.

2000-01-01

A method based on using solid state nuclear track detectors (SSNTD) CR- 39 and LR-115 type II and calculating the probabilities for the alpha particles emitted by the uranium and thorium series to reach and be registered on these films was utilized for uranium and thorium contents determination in various geological samples. The distribution of uranium and thorium in different volcanic rocks has been investigated using the track fission method. In this work, the uranium and thorium contents have been determined in different volcanic rock samples by using CR-39 and LR-115 type II solid state nuclear track detectors (SSNTD). The mean critical angles of etching of the solid state nuclear track detectors utilized have been calculated. A petrographical study of the volcanic rock thin layers studied has been conducted. The uranium and thorium distribution inside different rock thin layers has been studied. The mechanism of inclusion of the uranium and thorium nuclei inside the volcanic rock samples studied has been investigated. (author)

Application of hanging drop technique for stem cell differentiation and cytotoxicity studies.

Science.gov (United States)

Banerjee, Meenal; Bhonde, Ramesh R

2006-05-01

The aim of our study is to explore the possibility of using an ancient method of culture technique- the hanging drop technique for stem cell differentiation and cytotoxicity testing. We demonstrate here a variety of novel applications of this age old technique not only to harness the differentiation potential of stem cells into specific lineages but also for cytotoxicity studies. Here we have prepared hanging drop cultures by placing 20 microl micro-drops of nutrient media and 10% Fetal Calf Serum (FCS) containing cells of interest on the lids of 60 mm dishes. Bottom plates of the dishes were filled with sterile Phosphate Buffer Saline (PBS) to avoid desiccation of samples. Lids were then placed on the bottom plates to achieve hanging drop cultures. We utilized this technique for cultivation of ciliated epithelia to study cytotoxicity and differentiation of bone marrow stromal cells. Most importantly the modified culture technique presented here is simple, economical and cost effective in terms of the time taken and the reagents required and are amenable to goal specific modification such as cytotoxicity testing. It is advantageous over the existing system in terms of retention of viability and functionality for longer duration and for providing three dimensional growth micro-environment making it useful for organotypic cultures and in vivo simulation.

The formation of intestinal organoids in a hanging drop culture.

Science.gov (United States)

Panek, Malgorzata; Grabacka, Maja; Pierzchalska, Malgorzata

2018-01-25

Recently organoids have become widely used in vitro models of many tissue and organs. These type of structures, originated from embryonic or adult mammalian intestines, are called "mini guts". They organize spontaneously when intestinal crypts or stem cells are embedded in the extracellular matrix proteins preparation scaffold (Matrigel). This approach has some disadvantages, as Matrigel is undefined (the concentrations of growth factors and other biologically active components in it may vary from batch to batch), difficult to handle and expensive. Here we show that the organoids derived from chicken embryo intestine are formed in a hanging drop without embedding, providing an attractive alternative for currently used protocols. Using this technique we obtained compact structures composed of contiguous organoids, which were generally similar to chicken organoids cultured in Matrigel in terms of morphology and expression of intestinal epithelial markers. Due to the simplicity, high reproducibility and throughput capacity of hanging drop technique our model may be applied in various studies concerning the gut biology.

The United States Polar Rock Repository: A geological resource for the Earth science community

Science.gov (United States)

Grunow, Annie M.; Elliot, David H.; Codispoti, Julie E.

2007-01-01

The United States Polar Rock Repository (USPRR) is a U. S. national facility designed for the permanent curatorial preservation of rock samples, along with associated materials such as field notes, annotated air photos and maps, raw analytic data, paleomagnetic cores, ground rock and mineral residues, thin sections, and microfossil mounts, microslides and residues from Polar areas. This facility was established by the Office of Polar Programs at the U. S. National Science Foundation (NSF) to minimize redundant sample collecting, and also because the extreme cold and hazardous field conditions make fieldwork costly and difficult. The repository provides, along with an on-line database of sample information, an essential resource for proposal preparation, pilot studies and other sample based research that should make fieldwork more efficient and effective. This latter aspect should reduce the environmental impact of conducting research in sensitive Polar Regions. The USPRR also provides samples for educational outreach. Rock samples may be borrowed for research or educational purposes as well as for museum exhibits.

Flat-ramp vs. convex-concave thrust geometries in a deformable hanging wall: new insights from analogue modeling experiments

Science.gov (United States)

Almeida, Pedro; Tomas, Ricardo; Rosas, Filipe; Duarte, Joao; Terrinha, Pedro

2015-04-01

Different modes of strain accommodation affecting a deformable hanging-wall in a flat-ramp-flat thrust system were previously addressed through several (sandbox) analog modeling studies, focusing on the influence of different variables, such as: a) thrust ramp dip angle and friction (Bonini et al, 2000); b) prescribed thickness of the hanging-wall (Koy and Maillot, 2007); and c) sin-thrust erosion (compensating for topographic thrust edification, e.g. Persson and Sokoutis, 2002). In the present work we reproduce the same experimental procedure to investigate the influence of two different parameters on hanging-wall deformation: 1) the geometry of the thrusting surface; and 2) the absence of a velocity discontinuity (VD) that is always present in previous similar analogue modeling studies. Considering the first variable we use two end member ramp geometries, flat-ramp-flat and convex-concave, to understand the control exerted by the abrupt ramp edges in the hanging-wall stress-strain distribution, comparing the obtain results with the situation in which such edge singularities are absent (convex-concave thrust ramp). Considering the second investigated parameter, our motivation was the recognition that the VD found in the different analogue modeling settings simply does not exist in nature, despite the fact that it has a major influence on strain accommodation in the deformable hanging-wall. We thus eliminate such apparatus artifact from our models and compare the obtained results with the previous ones. Our preliminary results suggest that both investigated variables play a non-negligible role on the structural style characterizing the hanging-wall deformation of convergent tectonic settings were such thrust-ramp systems were recognized. Acknowledgments This work was sponsored by the Fundação para a Ciência e a Tecnologia (FCT) through project MODELINK EXPL/GEO-GEO/0714/2013. Pedro Almeida wants to thank to FCT for the Ph.D. grant (SFRH/BD/52556/2014) under the

Determination of the mechanical parameters of rock mass based on a GSI system and displacement back analysis

Science.gov (United States)

Kang, Kwang-Song; Hu, Nai-Lian; Sin, Chung-Sik; Rim, Song-Ho; Han, Eun-Cheol; Kim, Chol-Nam

2017-08-01

It is very important to obtain the mechanical paramerters of rock mass for excavation design, support design, slope design and stability analysis of the underground structure. In order to estimate the mechanical parameters of rock mass exactly, a new method of combining a geological strength index (GSI) system with intelligent displacment back analysis is proposed in this paper. Firstly, average spacing of joints (d) and rock mass block rating (RBR, a new quantitative factor), surface condition rating (SCR) and joint condition factor (J c) are obtained on in situ rock masses using the scanline method, and the GSI values of rock masses are obtained from a new quantitative GSI chart. A correction method of GSI value is newly introduced by considering the influence of joint orientation and groundwater on rock mass mechanical properties, and then value ranges of rock mass mechanical parameters are chosen by the Hoek-Brown failure criterion. Secondly, on the basis of the measurement result of vault settlements and horizontal convergence displacements of an in situ tunnel, optimal parameters are estimated by combination of genetic algorithm (GA) and numerical simulation analysis using FLAC3D. This method has been applied in a lead-zinc mine. By utilizing the improved GSI quantization, correction method and displacement back analysis, the mechanical parameters of the ore body, hanging wall and footwall rock mass were determined, so that reliable foundations were provided for mining design and stability analysis.

Dynamic Stability of the Rate, State, Temperature, and Pore Pressure Friction Model at a Rock Interface

Science.gov (United States)

Sinha, Nitish; Singh, Arun K.; Singh, Trilok N.

2018-05-01

In this article, we study numerically the dynamic stability of the rate, state, temperature, and pore pressure friction (RSTPF) model at a rock interface using standard spring-mass sliding system. This particular friction model is a basically modified form of the previously studied friction model namely the rate, state, and temperature friction (RSTF). The RSTPF takes into account the role of thermal pressurization including dilatancy and permeability of the pore fluid due to shear heating at the slip interface. The linear stability analysis shows that the critical stiffness, at which the sliding becomes stable to unstable or vice versa, increases with the coefficient of thermal pressurization. Critical stiffness, on the other hand, remains constant for small values of either dilatancy factor or hydraulic diffusivity, but the same decreases as their values are increased further from dilatancy factor (˜ 10^{ - 4} ) and hydraulic diffusivity (˜ 10^{ - 9} {m}2 {s}^{ - 1} ) . Moreover, steady-state friction is independent of the coefficient of thermal pressurization, hydraulic diffusivity, and dilatancy factor. The proposed model is also used for predicting time of failure of a creeping interface of a rock slope under the constant gravitational force. It is observed that time of failure decreases with increase in coefficient of thermal pressurization and hydraulic diffusivity, but the dilatancy factor delays the failure of the rock fault under the condition of heat accumulation at the creeping interface. Moreover, stiffness of the rock-mass also stabilizes the failure process of the interface as the strain energy due to the gravitational force accumulates in the rock-mass before it transfers to the sliding interface. Practical implications of the present study are also discussed.

Enhancement of nucleation during hanging drop protein crystallization using HF treatment of cover glasses

Energy Technology Data Exchange (ETDEWEB)

Guo, Yun-Zhu; Yin, Da-Chuan; Lu, Qin-Qin; Wang, Xi-Kai; Liu, Jun [Key Laboratory for Space Bioscience and Biotechnology, Faculty of Life Sciences, Northwestern Polytechnical University, Xi' an 710072, Shaanxi (China)

2010-02-15

We examined a simple approach, i.e., etching cover glasses using hydrofluoric acid (HF), to determine whether cover glass treatment enhances nucleation in hanging drop protein crystallization. Hen egg white lysozyme and proteinase K were used as the model proteins. We found that the treatment increased the success rate of crystallization. The results indicated that the simple treatment, which is easy to adopt without changing much in the hanging drop method, can be utilized as an alternative method to enhance protein crystallization screens (copyright 2010 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Neurological outcomes following suicidal hanging: A prospective study of 101 patients

Directory of Open Access Journals (Sweden)

Mohammed Turab Jawaid

2017-01-01

Full Text Available Context: Survivors of suicidal hanging can have variable neurological outcomes – from complete recovery to irreversible brain damage. Literature on the neurological outcomes in these patients is confined to retrospective studies and case series. Hence, this prospective study was carried out. Aims: The aim is to study the neurological outcomes in suicidal hanging. Settings and Design: This was a prospective observational study carried out from July 2014 to July 2016. Subjects and Methods: Consecutive patients admitted to the emergency and medicine wards were included in the study. Details of the clinical and radiological findings, course in hospital and at 1 month postdischarge were analyzed. Statistical Analysis Used: Statistical analysis was performed using IBM SPSS advanced statistics 20.0 (SPSS Inc., Chicago, USA. Univariate analysis was performed using Chi-square test for significance and Odd's ratio was calculated. Results: Of the 101 patients, 6 died and 4 had residual neuro deficits. Cervical spine injury was seen in 3 patients. Interestingly, 39 patients could not remember the act of hanging (retrograde amnesia. Hypotension, pulmonary edema, Glasgow coma scale (GCS score <8 at admission, need for mechanical ventilation, and cerebral edema on plain computed tomography were more in those with amnesia as compared to those with normal memory and these findings were statistically significant. Conclusions: Majority of patients recovered without any sequelae. Routine imaging of cervical spine may not be warranted in all patients, even in those with poor GCS. Retrograde amnesia might be more common than previously believed and further studies are needed to analyze this peculiar feature.

Prognosis at 6 and 12months after self-attempted hanging.

Science.gov (United States)

Gantois, Guillaume; Parmentier-Decrucq, Erika; Duburcq, Thibault; Favory, Raphaël; Mathieu, Daniel; Poissy, Julien

2017-11-01

Patients surviving a self-attempted hanging have a total neurological recovery in 57-77% of cases at hospital discharge, but no long-term data are available. In this observational study, all patients hospitalized post-self-attempted hanging in the intensive care unit (ICU) in a 5-year period were included. Neurological evaluations at 6 and 12months were performed according to Cerebral Performance Category (CPC) scores. Factors associated with neurological recovery were determined by comparing CPC2+3+4 (bad recovery) vs. CPC1 (good recovery). Of 231 patients included, 104 (47%) were found to have cardiac arrest (CA). Ninety-five (41%) patients died in the ICU: 93 (89%) in the CA group and 2 (1.6%) in the group without CA. Neurological evaluations at 6 and 12months were obtained in 97 of the 136 surviving patients. At 6months, in the CA group (n=9), the CPC score was 1 for 6 patients, 2 for 2, and 4 for 1 patient. In the group without CA (n=88), 79 patients had normal neurological status at 6months and 78 at 12months. Among these patients, 96% returned home, 77% returned to work, 16 (18%) patients re-attempted suicide within the year. Risk factors of neurological sequelae at 6months were a CA at the hanging site (P=0.045), an elevated diastolic blood pressure (87 vs. 70 mm Hg; P=0.04), a lower initial Glasgow score (4 vs. 5; P=0.04), and an elevated blood glucose level (139 vs. 113 mg/dL; Pgood neurological outcome. The rate of suicidal recidivism is particularly important, which justifies joint work with psychiatrists. Copyright © 2017 Elsevier Inc. All rights reserved.

Three-dimensional culture of buffalo granulosa cells in hanging drop mimics the preovulatory follicle stage.

Science.gov (United States)

Yadav, Monica; Agrawal, Himanshu; Pandey, Mamta; Singh, Dheer; Onteru, Suneel K

2018-03-01

Granulosa cell (GC) culture models mimicking the intrafollicular environment are limited. Such models have a great potential in reproductive toxicity studies. The buffalo, a monovulatory species like humans, could be a better model than polyovulatory rodents. Therefore, we targeted the development and characterization of three-dimensional (3D) culture systems for buffalo GCs. The GCs from small ovarian follicles (SF) maintained the CYP19 gene expression for 144 hr in a 2D culture system. Hence, GCs from SF were cultured directly in 3D using hanging drop and Poly-([2-hydroxyethyl methacrylate]) (polyHEMA) methods in the DMEM media containing 1 ng/ml FSH and 10 ng/ml IGF-1 for 144 hr. The expression profile of nine GC-specific transcripts; CYP19, TNFAIP6, AMH, PTI, NR4A1, FSHR, RUNX, LHR, and COX2/PTGS2; revealed that 3D-spheroids developed in hanging drop method maintained the GC phenotype of preovulatory follicles. Therefore, hanging drop method is a best method for culturing GCs to mimic the intrafollicular environment. © 2017 Wiley Periodicals, Inc.

In vitro differentiation of mouse embryonic stem (mES) cells using the hanging drop method.

Science.gov (United States)

Wang, Xiang; Yang, Phillip

2008-07-23

Stem cells have the remarkable potential to develop into many different cell types. When a stem cell divides, each new cell has the potential to either remain a stem cell or become another type of cell with a more specialized function, This promising of science is leading scientists to investigate the possibility of cell-based therapies to treat disease. When culture in suspension without antidifferentiation factors, embryonic stem cells spontaneously differentiate and form three-dimensional multicellular aggregates. These cell aggregates are called embryoid bodies(EB). Hanging drop culture is a widely used EB formation induction method. The rounded bottom of hanging drop allows the aggregation of ES cells which can provide mES cells a good environment for forming EBs. The number of ES cells aggregatied in a hanging drop can be controlled by varying the number of cells in the initial cell suspension to be hung as a drop from the lid of Petri dish. Using this method we can reproducibly form homogeneous EBs from a predetermined number of ES cells.

Controlling Vapor Pressure In Hanging-Drop Crystallization

Science.gov (United States)

Carter, Daniel C.; Smith, Robbie

1988-01-01

Rate of evaporation adjusted to produce larger crystals. Device helps to control vapor pressure of water and other solvents in vicinity of hanging drop of solution containing dissolved enzyme protein. Well of porous frit (sintered glass) holds solution in proximity to drop of solution containing protein or enzyme. Vapor from solution in frit controls evaporation of solvent from drop to control precipitation of protein or enzyme. With device, rate of nucleation limited to decrease number and increase size (and perhaps quality) of crystals - large crystals of higher quality needed for x-ray diffraction studies of macromolecules.

[Culture of pancreatic progenitor cells in hanging drop and on floating filter].

Science.gov (United States)

Ma, Feng-xia; Chen, Fang; Chi, Ying; Yang, Shao-guang; Lu, Shi-hong; Han, Zhong-chao

2013-06-01

To construct a method to culture pancreatic progenitor cells in hanging drop and on floating filter,and to examine if pancreatic progenitor cells can differentiate into mature endocrine cells with this method. Murine embryos at day 12.5 were isolated and digested into single cells,which were then cultured in hanging drop for 24h and formed spheres.Spheres were cultured on the filter for 6 days,which floated in the dish containing medium.During culture,the expressions of pancreas duodenum homeobox-1(PDX-1)and neurogenin3(Ngn3)were determined.The expressions of endocrine and exocrine markers,insulin,glucagon,and carboxypeptidase(CPA)were determined on day 7 by immunohistochemistry.Insulin secretion of spheres stimulated by glucose was detected by ELISA.The changes of pancreatic marker expressions during culture were monitored by real-time polymerase chain reaction(PCR). One day after the culture,there were still a large amount of PDX-1 positive cells in pancreatic spheres,and these cells proliferated.On day 3,high expression of Ngn3 was detected,and the Ngn3-positive cells did not proliferate.On day 7,The expressions of endocrine and exocrine markers in the differentiated pancreatic progenitor cells were detected,which were consistent with that in vivo.Insulin was secreted by spheres upon the stimulation of glucose. In hanging drop and on floating filter,pancreatic progenitor cells can differentiate into mature endocrine cells.

Hanging-wall deformation above a normal fault: sequential limit analyses

Science.gov (United States)

Yuan, Xiaoping; Leroy, Yves M.; Maillot, Bertrand

2015-04-01

The deformation in the hanging wall above a segmented normal fault is analysed with the sequential limit analysis (SLA). The method combines some predictions on the dip and position of the active fault and axial surface, with geometrical evolution à la Suppe (Groshong, 1989). Two problems are considered. The first followed the prototype proposed by Patton (2005) with a pre-defined convex, segmented fault. The orientation of the upper segment of the normal fault is an unknown in the second problem. The loading in both problems consists of the retreat of the back wall and the sedimentation. This sedimentation starts from the lowest point of the topography and acts at the rate rs relative to the wall retreat rate. For the first problem, the normal fault either has a zero friction or a friction value set to 25o or 30o to fit the experimental results (Patton, 2005). In the zero friction case, a hanging wall anticline develops much like in the experiments. In the 25o friction case, slip on the upper segment is accompanied by rotation of the axial plane producing a broad shear zone rooted at the fault bend. The same observation is made in the 30o case, but without slip on the upper segment. Experimental outcomes show a behaviour in between these two latter cases. For the second problem, mechanics predicts a concave fault bend with an upper segment dip decreasing during extension. The axial surface rooting at the normal fault bend sees its dips increasing during extension resulting in a curved roll-over. Softening on the normal fault leads to a stepwise rotation responsible for strain partitioning into small blocks in the hanging wall. The rotation is due to the subsidence of the topography above the hanging wall. Sedimentation in the lowest region thus reduces the rotations. Note that these rotations predicted by mechanics are not accounted for in most geometrical approaches (Xiao and Suppe, 1992) and are observed in sand box experiments (Egholm et al., 2007, referring

Generation of Homogenous Three-Dimensional Pancreatic Cancer Cell Spheroids Using an Improved Hanging Drop Technique.

Science.gov (United States)

Ware, Matthew J; Colbert, Kevin; Keshishian, Vazrik; Ho, Jason; Corr, Stuart J; Curley, Steven A; Godin, Biana

2016-04-01

In vitro characterization of tumor cell biology or of potential anticancer drugs is usually performed using tumor cell lines cultured as a monolayer. However, it has been previously shown that three-dimensional (3D) organization of the tumor cells is important to provide insights on tumor biology and transport of therapeutics. Several methods to create 3D tumors in vitro have been proposed, with hanging drop technique being the most simple and, thus, most frequently used. However, in many cell lines this method has failed to form the desired 3D tumor structures. The aim of this study was to design and test an easy-to-use and highly reproducible modification of the hanging drop method for tumor sphere formation by adding methylcellulose polymer. Most pancreatic cancer cells do not form cohesive and manageable spheres when the original hanging drop method is used, thus we investigated these cell lines for our modified hanging drop method. The spheroids produced by this improved technique were analyzed by histology, light microscopy, immunohistochemistry, and scanning electron microscopy. Results show that using the proposed simple method; we were able to produce uniform spheroids for all five of the tested human pancreatic cancer cell lines; Panc-1, BxPC-3, Capan-1, MiaPaCa-2, and AsPC-1. We believe that this method can be used as a reliable and reproducible technique to make 3D cancer spheroids for use in tumor biology research and evaluation of therapeutic responses, and for the development of bio-artificial tissues.

Suicidal hanging donors for lung transplantation: Is this chapter still closed? Midterm experience from a single center in United Kingdom.

Science.gov (United States)

Ananiadou, Olga; Schmack, Bastian; Zych, Bartlomiej; Sabashnikov, Anton; Garcia-Saez, Diana; Mohite, Prashant; Weymann, Alexander; Mansur, Ashham; Zeriouh, Mohamed; Marczin, Nandor; De Robertis, Fabio; Simon, Andre Rüdiger; Popov, Aron-Frederik

2018-04-01

In the context of limited donor pool in cardiothoracic transplantation, utilization of organs from high risk donors, such as suicidal hanging donors, while ensuring safety, is under consideration. We sought to evaluate the outcomes of lung transplantations (LTx) that use organs from this group.Between January 2011 and December 2015, 265 LTx were performed at our center. Twenty-two recipients received lungs from donors after suicidal hanging (group 1). The remaining 243 transplantations were used as a control (group 2). Analysis of recipient and donor characteristics as well as outcomes was performed.No statistically significant difference was found in the donor characteristics between analyzed groups, except for higher incidence of cardiac arrest, younger age and smoking history of hanging donors (P donor cause of death is not associated with poor mid-term survival or chronic lung allograft dysfunction following transplantation. These results encourage assessment of lungs from hanging donors, and their consideration for transplantation.

Importance of tissue biopsy in suicidal hanging deaths

Directory of Open Access Journals (Sweden)

Manal S. Bamousa

2015-12-01

The total number of cases was 62; 85.5% of the deceased were males, while 15% were females. The majority of cases (53% were among the age group of 20–30 years. Hemorrhage of the sternocleidomastoid muscle and carotid intimal tear were both found in 90% of cases. Thyroid congestion was detected in 91%, and Hashimoto’s thyroiditis was diagnosed in 2% of studied cases. The study discusses the importance of biopsy examination in hanging deaths and compares its results with other similar previous studies.

Rock-Mechanics Research. A Survey of United States Research to 1965, with a Partial Survey of Canadian Universities.

Science.gov (United States)

National Academy of Sciences - National Research Council, Washington, DC.

The results of a survey, conducted by the Committee on Rock Mechanics, to determine the status of training and research in rock mechanics in presented in this publication. In 1964 and 1965 information was gathered by questionnaires sent to industries, selected federal agencies, and universities in both the United States and Canada. Results are…

VOLTAMMETRY OF AQUEOUS CHLOROAURIC ACID WITH HANGING MERCURY DROP ELECTRODE

Czech Academy of Sciences Publication Activity Database

Korshunov, A.; Josypčuk, Bohdan; Heyrovský, Michael

2011-01-01

Roč. 76, č. 7 (2011), s. 929-936 ISSN 0010-0765 R&D Projects: GA ČR GAP206/11/1638; GA AV ČR IAA400400806; GA MŠk(CZ) LC06063 Institutional research plan: CEZ:AV0Z40400503 Keywords : aqueous chloauric acid * voltammetry * hanging mercury drop electrode Subject RIV: CG - Electrochemistry Impact factor: 1.283, year: 2011

Micro-ring structures stabilize microdroplets to enable long term spheroid culture in 384 hanging drop array plates.

Science.gov (United States)

Hsiao, Amy Y; Tung, Yi-Chung; Kuo, Chuan-Hsien; Mosadegh, Bobak; Bedenis, Rachel; Pienta, Kenneth J; Takayama, Shuichi

2012-04-01

Using stereolithography, 20 different structural variations comprised of millimeter diameter holes surrounded by trenches, plateaus, or micro-ring structures were prepared and tested for their ability to stably hold arrays of microliter sized droplets within the structures over an extended period of time. The micro-ring structures were the most effective in stabilizing droplets against mechanical and chemical perturbations. After confirming the importance of micro-ring structures using rapid prototyping, we developed an injection molding tool for mass production of polystyrene 3D cell culture plates with an array of 384 such micro-ring surrounded through-hole structures. These newly designed and injection molded polystyrene 384 hanging drop array plates with micro-rings were stable and robust against mechanical perturbations as well as surface fouling-facilitated droplet spreading making them capable of long term cell spheroid culture of up to 22 days within the droplet array. This is a significant improvement over previously reported 384 hanging drop array plates which are susceptible to small mechanical shocks and could not reliably maintain hanging drops for longer than a few days. With enhanced droplet stability, the hanging drop array plates with micro-ring structures provide better platforms and open up new opportunities for high-throughput preparation of microscale 3D cell constructs for drug screening and cell analysis.

Preliminary state-of-the-art survey: mining techniques for salt and other rock types

Energy Technology Data Exchange (ETDEWEB)

1976-12-01

This is a systematic review of the state-of-the-art of underground mining and excavation technology in the U.S. as applied to salt, limestone, shale, and granite. Chapter 2 covers the basic characteristics of these rock types, the most frequently used underground mining methods, shaft and slope entry construction, equipment, and safety and productivity data. Chapters 3 and 4 summarize underground salt and limestone mining in the U.S. Chapter 5 shows that large amounts of thick shale exist in the U.S., but little is mined. Chapter 6 discusses underground excavations into granite-type rocks. Suggestions are given in the last chapter for further study. (DLC)

[A homicidal strangulation by ligature, disguised as a suicidal hanging].

Science.gov (United States)

Ueno, Y; Fukunaga, T; Nakagawa, K; Imabayashi, T; Fujiwara, S; Adachi, J; Mizoi, Y

1989-02-01

A naked 38-year-old woman was found dead, lying beside a bed in a guest room of a hotel. A cotton cord was looped around her neck, with one end tied to a bedpost. Thus it seemed that she had hanged herself in a lying position. Yet, certain suspicious factors gave rise to doubts. The hair and a necklace were intertwined with the cord and a man that had been staying in the same room had fled. On the postmortem examination, marked congestion and many petechial haemorrhages were seen in the face and the upper area of the neck, also in conjunctiva. A light-brown and highly dry ligature mark, about one centimeter in width, was found on the neck. The mark, crossing the front of the neck, was clearly evident from the back to the right side of the neck. The lower borders of the congestion and petechial haemorrhages in the face and neck were located 1 or 2 centimeters above the ligature mark. On the left side of the neck, another pale ligature mark with slight subcutaneous haemorrhages was seen between the dry mark and the lower border of the congested part of the neck. A similar ligature mark also was found on the back of the neck. On internal examination, congestion of the cervical lymph nodes and haemorrhages in the cervical muscles were recognized in the areas of the cutaneous congestion. These findings supported suspicions that the dry ligature mark had been caused by hanging after her death, and that the light ligature mark with slight subcutaneous haemorrhages on the left side and back of the neck had been caused by strangulation, which had brought on the victim's death. Therefore, it was decided that her death had been disguised as a suicidal hanging, after she had been strangled by ligature. A week later, her former husband was arrested and confessed his crime.

Liver hanging maneuver for right hemiliver in situ donation--anatomical considerations.

Science.gov (United States)

Trotovsek, B; Gadzijev, E M; Ravnik, D; Hribernik, M

2006-01-01

An anatomical study was carried out to evaluate the safety of the liver hanging maneuver for the right hemiliver in living donor and in situ splitting transplantation. During this procedure a 4-6 cm blind dissection is performed between the inferior vena cava and the liver. Short subhepatic veins entering the inferior vena cava from segments 1 and 9 could be torn with consequent hemorrhage. One hundred corrosive casts of livers were evaluated to establish the position and diameter of short subhepatic veins and the inferior right hepatic vein. The average distance from the right border of the inferior vena cava to the opening of segment 1 veins was 16.7+/-3.4 mm and to the entrance of segment 9 veins was 5.0+/-0.5 mm. The width of the narrowest point on the route of blind dissection was determined, with the average value being 8.7+/-2.3 mm (range 2-15 mm). The results show that the liver hanging maneuver is a safe procedure. A proposed route of dissection minimizes the risk of disrupting short subhepatic veins (7%).

THE BEHAVIOURAL REACTION OF WEANERS TO HANGING TOYS: WOODEN BALL AND AROMATIZED WOODEN BALL – WAY TO REDUCE AGGRESSION AFTER MIXING

Directory of Open Access Journals (Sweden)

Jacek NOWICKI

2008-05-01

Full Text Available The behaviour of weaners after mixing housed in pens equipped with hanging wooden ball, aromatized with vanilla fluid hanging wooden ball and without enrichment was evaluated. It was found that both enrichments reduced aggression, however the most interesting for weaners was the aromatized wooden ball.

Perbandingan Ko-kultur 2D dan 3D dengan Metode Hanging Drop untuk Menghasilkan Micro-environment yang Lebih Relevan Secara Klinis

Directory of Open Access Journals (Sweden)

Radiana Dhewayani Antarianto

2017-09-01

Full Text Available Ko-kultur sel 2 dimensi (2D kurang menyerupai micro-environment seperti in vivo sedangkan ko-kultur 3 dimensi (3D membentuk mikromassa yang lebih mirip micro-environment in vivo sehingga bermanfaat dalam penelitian biologi dasar. Penelitian ini membandingkan ko-kultur 2D dan 3D sel punca serta sel stelata hepatik dengan metode hanging drop untuk menilai morfologi sel dan pembentukan sferoid dari mikromassa yang terbentuk. Studi in vitro ini dilakukan di Pusat Virologi dan Kanker Patobiologi (PRVKP UI dan laboratorium histologi FKUI pada bulan September 2015 sampai Oktober 2016 menggunakan sel punca yang diisolasi dari darah tali pusat manusia dan sel lestari LX2 (stelata hepatik manusia. Darah tali pusat disortir dengan MACS CD34 dan dianalisis flowcytometry. Ko-kultur sel punca sumsum tulang atau darah tali pusat dan LX2 dilakukan dengan metode hanging drop untuk ko-kultur 2D dan ko-kultur 3D. Triplikasi eksperimen dilakukan untuk tiap set ko-kultur. Hasilnya menunjukkan terdapat perbedaan morfologi ko-kultur 2D dan 3D hanging drop dibandingkan monokultur. Di ko-kultur 2D terdapat mikromassa dan di monokultur 2D tidak terbentuk mikromassa. Di ko-kultur 3D hanging drop, terdapat sferoid yang lebih kecil dibandingkan monokultur 3D hanging drop. Morfologi sel ko-kultur 2D dan 3D dengan metode hanging drop dibandingkan monokultur menunjukkan perubahan fenotip sel-sel yang tergabung dalam mikromassa. Normal 0 false false false false IN X-NONE X-NONE Normal 0 false false false false IN X-NONE X-NONE The preparation of Drosophila embryos for live-imaging using the hanging drop protocol.

Science.gov (United States)

Reed, Bruce H; McMillan, Stephanie C; Chaudhary, Roopali

2009-03-13

Green fluorescent protein (GFP)-based timelapse live-imaging is a powerful technique for studying the genetic regulation of dynamic processes such as tissue morphogenesis, cell-cell adhesion, or cell death. Drosophila embryos expressing GFP are readily imaged using either stereoscopic or confocal microscopy. A goal of any live-imaging protocol is to minimize detrimental effects such as dehydration and hypoxia. Previous protocols for preparing Drosophila embryos for live-imaging analysis have involved placing dechorionated embryos in halocarbon oil and sandwiching them between a halocarbon gas-permeable membrane and a coverslip. The introduction of compression through mounting embryos in this manner represents an undesirable complication for any biomechanical-based analysis of morphogenesis. Our method, which we call the hanging drop protocol, results in excellent viability of embryos during live imaging and does not require that embryos be compressed. Briefly, the hanging drop protocol involves the placement of embryos in a drop of halocarbon oil that is suspended from a coverslip, which is, in turn, fixed in position over a humid chamber. In addition to providing gas exchange and preventing dehydration, this arrangement takes advantage of the buoyancy of embryos in halocarbon oil to prevent them from drifting out of position during timelapse acquisition. This video describes in detail how to collect and prepare Drosophila embryos for live imaging using the hanging drop protocol. This protocol is suitable for imaging dechorionated embryos using stereomicroscopy or any upright compound fluorescence microscope.

Digital microfluidics for automated hanging drop cell spheroid culture.

Science.gov (United States)

Aijian, Andrew P; Garrell, Robin L

2015-06-01

Cell spheroids are multicellular aggregates, grown in vitro, that mimic the three-dimensional morphology of physiological tissues. Although there are numerous benefits to using spheroids in cell-based assays, the adoption of spheroids in routine biomedical research has been limited, in part, by the tedious workflow associated with spheroid formation and analysis. Here we describe a digital microfluidic platform that has been developed to automate liquid-handling protocols for the formation, maintenance, and analysis of multicellular spheroids in hanging drop culture. We show that droplets of liquid can be added to and extracted from through-holes, or "wells," and fabricated in the bottom plate of a digital microfluidic device, enabling the formation and assaying of hanging drops. Using this digital microfluidic platform, spheroids of mouse mesenchymal stem cells were formed and maintained in situ for 72 h, exhibiting good viability (>90%) and size uniformity (% coefficient of variation <10% intraexperiment, <20% interexperiment). A proof-of-principle drug screen was performed on human colorectal adenocarcinoma spheroids to demonstrate the ability to recapitulate physiologically relevant phenomena such as insulin-induced drug resistance. With automatable and flexible liquid handling, and a wide range of in situ sample preparation and analysis capabilities, the digital microfluidic platform provides a viable tool for automating cell spheroid culture and analysis. © 2014 Society for Laboratory Automation and Screening.

Application of Hanging Drop Technique for Kidney Tissue Culture.

Science.gov (United States)

Wang, Shaohui; Wang, Ximing; Boone, Jasmine; Wie, Jin; Yip, Kay-Pong; Zhang, Jie; Wang, Lei; Liu, Ruisheng

2017-01-01

The hanging drop technique is a well-established method used in culture of animal tissues. However, this method has not been used in adult kidney tissue culture yet. This study was to explore the feasibility of using this technique for culturing adult kidney cortex to study the time course of RNA viability in the tubules and vasculature, as well as the tissue structural integrity. In each Petri dish with the plate covered with sterile buffer, a section of mouse renal cortex was cultured within a drop of DMEM culture medium on the inner surface of the lip facing downward. The tissue were then harvested at each specific time points for Real-time PCR analysis and histological studies. The results showed that the mRNA level of most Na+ related transporters and cotransporters were stably maintained within 6 hours in culture, and that the mRNA level of most receptors found in the vasculature and glomeruli were stably maintained for up to 9 days in culture. Paraffin sections of the cultured renal cortex indicated that the tubules began to lose tubular integrity after 6 hours, but the glomeruli and vasculatures were still recognizable up to 9 days in culture. We concluded that adult kidney tissue culture by hanging drop method can be used to study gene expressions in vasculature and glomeruli. © 2017 The Author(s). Published by S. Karger AG, Basel.

Application of Hanging Drop Technique for Kidney Tissue Culture

Directory of Open Access Journals (Sweden)

Shaohui Wang

2017-05-01

Full Text Available Background/Aims: The hanging drop technique is a well-established method used in culture of animal tissues. However, this method has not been used in adult kidney tissue culture yet. This study was to explore the feasibility of using this technique for culturing adult kidney cortex to study the time course of RNA viability in the tubules and vasculature, as well as the tissue structural integrity. Methods: In each Petri dish with the plate covered with sterile buffer, a section of mouse renal cortex was cultured within a drop of DMEM culture medium on the inner surface of the lip facing downward. The tissue were then harvested at each specific time points for Real-time PCR analysis and histological studies. Results: The results showed that the mRNA level of most Na+ related transporters and cotransporters were stably maintained within 6 hours in culture, and that the mRNA level of most receptors found in the vasculature and glomeruli were stably maintained for up to 9 days in culture. Paraffin sections of the cultured renal cortex indicated that the tubules began to lose tubular integrity after 6 hours, but the glomeruli and vasculatures were still recognizable up to 9 days in culture. Conclusions: We concluded that adult kidney tissue culture by hanging drop method can be used to study gene expressions in vasculature and glomeruli.

Evaluation of a hanging core support concept for LMR application

International Nuclear Information System (INIS)

Burelbach, J.P.; Cha, B.K.; Huebotter, P.R.; Kann, W.J.; Pan, Y.C.; Saiveau, J.G.; Seidensticker, R.W.; Wu, T.S.

1985-01-01

The paper describes an innovative design concept for a liquid metal reactor (LMR) core support structure (CSS). A hanging core support structure is described and analyzed. The design offers inherent safety features, constructability advantages, and potential cost reductions. Some safety considerations are examined which include the in-service inspection (ISI), the backup support system and the structural behavior in a hypothetical case of a broken beam in the core support structure

A state-of-the-art anisotropic rock deformation model incorporating the development of mobilised shear strength

Science.gov (United States)

Noor, M. J. Md; Jobli, A. F.

2018-04-01

Currently rock deformation is estimated using the relationship between the deformation modulus Em and the stress-strain curve. There have been many studies conducted to estimate the value of Em. This Em is basically derived from conducting unconfined compression test, UCS. However, the actual stress condition of the rock in the ground is anisotropic stress condition where the rock mass is subjected to different confining and vertical pressures. In addition, there is still no empirical or semi-empirical framework that has been developed for the prediction of rock stress-strain response under anisotropic stress condition. Arock triaxial machine GCTS Triaxial RTX-3000 has been deployed to obtain the anisotropic stress-strain relationship for weathered granite grade II from Rawang, Selangor sampled at depth of 20 m and subjected to confining pressure of 2 MPa, 7.5 MPa and 14 MPa. The developed mobilised shear strength envelope within the specimen of 50 mm diameter and 100 mm height during the application of the deviator stress is interpreted from the stress-strain curves. These mobilised shear strength envelopes at various axial strains are the intrinsic property and unique for the rock. Once this property has been established then it is being used to predict the stress-strain relationship at any confining pressure. The predicted stress-strain curves are compared against the curves obtained from the tests. A very close prediction is achieved to substantiate the applicability of this rock deformation model. This is a state-of-the art rock deformation theory which characterise the deformation base on the applied load and the developed mobilised shear strength within the rock body.

Thermostatic tissue platform for intravital microscopy: 'the hanging drop' model.

Science.gov (United States)

Pavlovic, Dragan; Frieling, Helge; Lauer, Kai-Stephan; Bac, Vo Hoai; Richter, Joern; Wendt, Michael; Lehmann, Christian; Usichenko, Taras; Meissner, Konrad; Gruendling, Matthias

2006-11-01

Intravital microscopy imposes the particular problem of the combined control of the body temperature of the animal and the local temperature of the observed organ or tissues. We constructed and tested, in the rat ileum microcirculation preparation, a new organ-support platform. The platform consisted of an organ bath filled with physiological solution, and contained a suction tube, a superfusion tube, an intestine-support hand that was attached to a micromanipulator and a thermometer probe. To cover the intestine we used a cover glass plate with a plastic ring glued on its upper surface. After a routine procedure (anaesthesia, monitoring and surgery), the intestine segment (2-3 cm long) was gently exteriorized and placed on the 'hand' of the organ support. A small part of the intestine formed a small 'island' in the bath that was filled with physiological salt solution. The cover glass was secured in place. The physiological salt solution from the superfusion tube, which was pointed to the lower surface of the cover glass, formed a 'hanging drop'. The objective of the microscope was then immersed into distilled water that was formed by the cover glass plastic ring. The 'hanging drop' technique prevented any tissue quenching, ensured undisturbed microcirculation, provided for stable temperature and humidity, and permitted a clear visual field.

Evaluation of the layering of rock strata and basement rock depth of ...

African Journals Online (AJOL)

The layering of rock strata and depth to the basement rocks of a Federal University Teaching Hospital premises in Northern Nigeria was investigated in this study with the aim of providing 2D geo-electrical resistivity images of the subsurface for geotechnical development using a modern and state-of-the-art field instrument, ...

Numerical simulation of the effects of hanging sound absorbers on TABS cooling performance

DEFF Research Database (Denmark)

Rage, Nils; Kazanci, Ongun Berk; Olesen, Bjarne W.

2016-01-01

simulating a two-person office of 20 m2, with a typical cooling load of 42 W/m2. The results show that covering 60% of the ceiling surface with sound absorbers hanging at 300 mm from the ceiling active deck is expected to reduce the cooling capacity coefficient of TABS by 15.8%. This drops to 25......Recently there has been a considerable increase in the use of Thermally-Active Building Systems (TABS) in Europe as an energy-efficient and economical cooling and heating solution for buildings. However, this widespread solution requires large uncovered hard surfaces indoors, which can lead...... to a degradation of the room acoustic comfort. Therefore, challenges arise when this system has to be combined with acoustic requirements. Soffit-hanging sound absorbers embody a promising solution. This study focuses on quantifying their impact on the cooling performance of TABS, assessed by means of the cooling...

Transfer, imaging, and analysis plate for facile handling of 384 hanging drop 3D tissue spheroids.

Science.gov (United States)

Cavnar, Stephen P; Salomonsson, Emma; Luker, Kathryn E; Luker, Gary D; Takayama, Shuichi

2014-04-01

Three-dimensional culture systems bridge the experimental gap between in vivo and in vitro physiology. However, nonstandardized formation and limited downstream adaptability of 3D cultures have hindered mainstream adoption of these systems for biological applications, especially for low- and moderate-throughput assays commonly used in biomedical research. Here we build on our recent development of a 384-well hanging drop plate for spheroid culture to design a complementary spheroid transfer and imaging (TRIM) plate. The low-aspect ratio wells of the TRIM plate facilitated high-fidelity, user-independent, contact-based collection of hanging drop spheroids. Using the TRIM plate, we demonstrated several downstream analyses, including bulk tissue collection for flow cytometry, high-resolution low working-distance immersion imaging, and timely reagent delivery for enzymatic studies. Low working-distance multiphoton imaging revealed a cell type-dependent, macroscopic spheroid structure. Unlike ovarian cancer spheroids, which formed loose, disk-shaped spheroids, human mammary fibroblasts formed tight, spherical, and nutrient-limited spheroids. Beyond the applications we describe here, we expect the hanging drop spheroid plate and complementary TRIM plate to facilitate analyses of spheroids across the spectrum of throughput, particularly for bulk collection of spheroids and high-content imaging.

Experimental Rock-on-Rock Abrasive Wear Under Aqueous Conditions: its Role in Subglacial Abrasion

Science.gov (United States)

Rutter, E. H.; Lee, A. G.

2003-12-01

We have determined experimentally the rate of abrasive wear of rock on rock for a range of rock types as a function of normal stress and shear displacement. Unlike abrasive wear in fault zones, where wear products accumulate as a thickening gouge zone, in our experiments wear particles were removed by flowing water. The experiments are thus directly pertinent to one of the most important processes in subglacial erosion, and to some extent in river incision. Wear was produced between rotating discs machined from rock samples and measured from the progressive approach of the disc axes towards each other under various levels of normal load. Shear displacements of several km were produced. Optical and scanning electron microscopy were used to study the worn rock surfaces, and particle size distributions in wear products were characterized using a laser particle size analyzer. Rock types studied were sandstones of various porosities and cement characteristics, schists and a granite. In all cases abrasion rate decreased logarithmically with displacement by up to 2 orders of magnitude until a steady state was approached, but only after at least 1 km displacement. The more porous, less-well cemented rocks wore fastest. Amount of abrasion could be characterized quantitatively using an exponentially decaying plus a steady-state term. Wear rate increased non-linearly with normal contact stress, apparently to an asymptote defined by the unconfined compressive strength. Microstructural study showed that the well-cemented and/or lowest porosity rocks wore by progressive abrasion of grains without plucking, whereas whole grains were plucked out of weakly-cemented and/or more porous rocks. This difference in behavior was reflected in wear-product particle size distributions. Where whole-grain plucking was possible, wear products were dominated by particles of the original grain size rather than finer rock flour. Comparison of our results to glacier basal abrasive wear estimated

Effect of loose spring skirt mounting position on vibration damping in a multi segment hanging cantilever

International Nuclear Information System (INIS)

Nazeer, M.M.; Khan, A.F.; Shah, R.H; Afzal, M.; Ahmed, N.

2001-01-01

The loose spring skirt clearance is the major factor effecting the damping and amplitude control of randomly excited vibrations in a vertically hanging cantilever. However, the spring's mounting position also has an important role to play. In this work, the results of computational model as well as that of experimental set-up for various spring mounting positions having optimum annular clearance between skirted member and the skirt are presented and their vibration damping response is analyzed. It is observed that lower is the mounting position, the better is the damping and its maximum value is attained when the bottom end of spring skirt and the hanging cantilever are mutually flushed. (author)

Design of 3D printed insert for hanging culture of Caco-2 cells

International Nuclear Information System (INIS)

Shen, Chong; Meng, Qin; Zhang, Guoliang

2015-01-01

A Caco-2 cell culture on Transwell, an alternative testing to animal or human testing used in evaluating drug intestinal permeability, incorrectly estimated the absorption of actively transported drugs due to the low expression of membrane transporters. Similarly, three-dimensional (3D) cultures of Caco-2 cells, which have been recommended to be more physiological relevant, were not superior to the Transwell culture in either accuracy or convenience in drug permeability testing. Using rapid 3D printing prototyping techniques, this study proposed a hanging culture of Caco-2 cells that performed with high accuracy in predicting drug permeability in humans. As found, hanging cultured Caco-2 cells formed a confluent monolayer and maintained high cell viability on the 3D printed insert. Compared with the normal culture on Transwell, the Caco-2 cells on the 3D printed insert presented ∼30–100% higher brush border enzyme activity and ∼2–7 folds higher activity of P-glycoprotein/multidrug resistance-associated protein 2 during 21 days of incubation. For the eight membrane transporter substrates, the predictive curve of the 3D printing culture exhibited better linearity (R 2  = 0.92) to the human oral adsorption than that of the Transwell culture (R 2  = 0.84), indicating better prediction by the 3D printing culture. In this regard, the 3D printed insert for hanging culture could be potentially developed as a convenient and low-cost tool for testing drug oral absorption. (paper)

Study of electrochemical behavior of desatinib using hanging mercury drop electrode and gold disc electrode

Czech Academy of Sciences Publication Activity Database

Nováková, Kateřina; Navrátil, Tomáš; Jaklová Dytrtová, Jana; Jakl, M.

2015-01-01

Roč. 11, č. 1 (2015), s. 116-116 ISSN 1336-7242 Institutional support: RVO:61388955 ; RVO:61388963 Keywords : electrochemistry * hanging mercury drop electrode * gold electrode Subject RIV: CG - Electrochemistry

Review of potential host rocks for radioactive wasste disposal in the southeast United States: Triassic basin subregion

International Nuclear Information System (INIS)

1980-10-01

Based on an evaluation of existing information, areas were identified within the Triassic basins of the southeastern United States with geologic properties considered favorable for containment of radioactive waste. The study region included both exposed and buried Triassic basins from Maryland to Georgia. These basins are long, narrow northeast-trending troughs filled with continental deposits derived from Paleozoic and Precambrian metamorphic and igneous rocks bordering the basins. The rocks are predominantly red in color and consist mainly of fanglomerates, conglomerates, arkosic sandstones, siltstones, claystones, shales, and argillites. The investigation identified 14 exposed and 5 buried basins within the study region. Candidate areas for further investigation were identified which meet the broad general criteria for tectonic stability, slow ground water movement, and long flow paths to the biosphere. These include: the Danville Triassic Basin in Virginia; the Dan River, Durham, and Wadesboro Triassic Basins in North Carolina; and the buried Florence and Dunbarton Triassic Basins in South Carolina. Other rock types in the southeast may prove more or less suitable as host rocks for a repository, but the available data suggest that the argillaceous Triassic rocks offer sufficient promise to be considered for additional study

Arbitrary-Level Hanging Nodes and Automatic Adaptivity in the hp-FEM

Czech Academy of Sciences Publication Activity Database

Šolín, Pavel; Červený, Jakub; Doležel, Ivo

2008-01-01

Roč. 77, č. 1 (2008), s. 117-132 ISSN 0378-4754 R&D Projects: GA ČR(CZ) GA102/07/0496; GA ČR GA102/05/0629; GA AV ČR IAA100760702 Institutional research plan: CEZ:AV0Z20570509 Keywords : constrained approximation * hanging nodes * hp-FEM Subject RIV: JA - Electronics ; Optoelectronics, Electrical Engineering Impact factor: 0.930, year: 2008

Late Cenozoic cooling history of the central Menderes Massif and the contribution of erosion to rock exhumation during active continental extension

Science.gov (United States)

Nilius, Nils-Peter; Wölfler, Andreas; Heineke, Caroline; Glotzbach, Christoph; Hetzel, Ralf; Hampel, Andrea; Akal, Cüneyt; Dunkl, István

2017-04-01

The Menderes Massif constitutes the western part of the Anatolide belt in western Turkey and experienced a prolonged history of post-orogenic extension. A large amount of the extension was accommodated by the two oppositely dipping Gediz and Büyük Menderes detachment faults, which led to the exhumation of the central Menderes Massif (Gessner et al., 2013). Previous studies proposed a synchronous, bivergent exhumation of the central Menderes Massif since the Miocene (Gessner et al., 2001), although only the evolution of the north-dipping Gediz detachment is well constrained (Buscher et al., 2013). Detailed structural and thermochronological investigations from the south-dipping Büyük Menderes detachment have still been missing. Here we present results from different thermochronometers, which constrain the cooling and exhumation history of footwall and hanging wall rocks of the Büyük Menderes detachment. Our new zircon and apatite (U-Th)/He and fission track ages of footwall rocks from the Büyük Menderes detachment document two phases of increased cooling and exhumation (Wölfler et al., in revision). The first episode of increased footwall exhumation ( 0.9 km/Myr) occurred during the middle Miocene, followed by a second phase during latest Miocene and Pliocene ( 1.0 km/Myr). Apatite fission track ages yield a slip rate for the Pliocene movement along the Büyük Menderes detachment of 3.0 (+1.1/-0.6) km/Myr. Thermochronological data of hanging wall units reflect a slow phase of exhumation ( 0.2 km/Myr) in the late Oligocene and an increased exhumation rate of 1.0 km/Myr during the early to middle Miocene, when hanging wall units cooled below 80 °C. In comparison with the Gediz detachment, our thermochronological data from the Büyük Menderes detachment confirms the concurrent activity of both detachments during the late Miocene and Pliocene. With respect to the relative importance of normal faulting and erosion to rock exhumation, a comparison with 10Be

Influence of different geological structures on stress–strain state of hard rock mass

Science.gov (United States)

Kuznetzov, NN; Fedotova, YuV

2018-03-01

The results of numerical simulation of stress–strain state in a hard rock mass area with the complex geological structures are presented. The variants of the stress value change are considered depending on the boundary conditions and physical properties of the model blocks. Furthermore, the possibility of in-situ stress formation under the influence of energy coming from the deeper Earth’s layers is demonstrated in terms of the Khibiny Massif.

Voltammetry of Aluminum Nanoparticles in Aqueous Media with Hanging Mercury Drop Electrode

Czech Academy of Sciences Publication Activity Database

Korshunov, A.; Heyrovský, Michael

2010-01-01

Roč. 22, 17-18 (2010), s. 1989-1993 ISSN 1040-0397. [International Conference on Modern Electroanalytical Methods. Prague, 09.12.2009-14.12.2009] R&D Projects: GA AV ČR IAA400400806 Institutional research plan: CEZ:AV0Z40400503 Keywords : linear cyclic voltammetry * Hanging mercury drop electrode * Aluminum nanoparticles dispersion Subject RIV: CG - Electrochemistry Impact factor: 2.721, year: 2010

Measurement of the Mass of an Object Hanging from a Spring--Revisited

Science.gov (United States)

Serafin, Kamil; Oracz, Joanna; Grzybowski, Marcin; Koperski, Maciej; Sznajder, Pawel; Zinkiewicz, Lukasz; Wasylczyk, Piotr

2012-01-01

In an open competition, students were to determine the mass of a metal cylinder hanging on a spring inside a transparent enclosure. With the time for experiments limited to 24 h due to the unexpectedly large number of participants, a few surprisingly accurate results were submitted, the best of them differing by no more than 0.5% from the true…

Ultrapotassic rocks geology from Salgueiro region, Pernambuco state, Brazil

International Nuclear Information System (INIS)

Silva Filho, A.F. da; Guimaraes, I.P.

1990-01-01

The Cachoeirinha-Salgueiro belt has Proterozoic age and is located in the Borborema Province, NE Brazil. The ultrapotassic rocks from Salgueiro region intrudes the Cachoeirinha-Salgueiro belt rocks. The ultrapotassics from Salgueiro region constitutes of three units; Serra do Livramento pluton, and two dyke swarms called respectively beige alkali feldspar granites and green alkali feldspar syenite/quartz-syenite. The Serra do Livramento pluton shows E-W direction, boudin shape, width between 0,15 and 2,10 km, and it is intruded into metamorphic rocks and into the Terra Nova complex. Detailed geological mapping at the Serra das Duas Irmas allowed us to establish the dyke swarm chronology. The mapping reveals seven intrusion episodes, into the Terra Nova pluton, of green alkali feldspar syenite/quartz-syenite and five episodes of bege alkali feldspar granite. They alternate between them in space and time, and there are evidence that they were intruded under the tectonic control of the Pernambuco lineament. A systematic whole-rock Rb-Sr geochronology was done in the green alkali feldspar syenite/quartz-syenite, and an age of 514,8 ± 20,3 Ma was obtained. The initial ratio is 0,710615 + 0,000441. The age obtained shows small error and an initial ratio compatible with a strong crustal contamination. (author)

Self-healing of excavation-disturbed rocks in the near field of underground cavities - exemplary measurements in rock salt and interpretation of preliminary results

International Nuclear Information System (INIS)

Wieczorek, K.; Schwarzianeck, P.; Rothfuchs, T.

2001-01-01

Excavation disturbed zones develop in all kinds of rock as a consequence of the opening of cavities. Such zones are characterized by a change in hydraulic behaviour which can form a problem with regard to the sealing of waste disposal areas. Rocks showing a plastic behaviour, like rock salt, have the potential of healing when the stress state which was disturbed by excavation returns to an advantageous state. If healing can reliably be predicted, the excavation disturbed zone may not form a long-term safety issue in rock salt. Investigations of permeability and stress state around lined and open excavations have been performed in order to relate hydraulic behaviour to stress state. First results which are presented here are promising. (authors)

Radon and rock bursts in deep mines

International Nuclear Information System (INIS)

Bulashevich, Yu.P.; Utkin, V.I.; Yurkov, A.K.; Nikolaev, V.V.

1996-01-01

Variation fields of radon concentration in time to ascertain stress-strain state of the North Ural bauxite mines have been studied. It is shown that dynamic changes in the stress-strain state of the rocks prior to the rock burst bring about variations in radon concentration in the observation wells. Depending on mutual positioning of the observation points and the rock burst epicenter, the above-mentioned variations differ in principle, reduction of radon concentration in the near zone and its increase in the far zone are observed [ru

Media additives to promote spheroid circularity and compactness in hanging drop platform.

Science.gov (United States)

Leung, Brendan M; Lesher-Perez, Sasha Cai; Matsuoka, Toshiki; Moraes, Christopher; Takayama, Shuichi

2015-02-01

Three-dimensional spheroid cultures have become increasingly popular as drug screening platforms, especially with the advent of different high throughput spheroid forming technologies. However, comparing drug efficacy across different cell types in spheroid culture can be difficult due to variations in spheroid morphologies and transport characteristics. Improving the reproducibility of compact, circular spheroids contributes to standardizing and increasing the fidelity of the desired gradient profiles in these drug screening three-dimensional tissue cultures. In this study we discuss the role that circularity and compaction has on spheroids, and demonstrate the impact methylcellulose (MethoCel) and collagen additives in the culture media can contribute to more compact and circular spheroid morphology. We demonstrate that improved spheroid formation is not a simple function of increased viscosity of the different macromolecule additives, suggesting that other macromolecular characteristics contribute to improved spheroid formation. Of the various macromolecular additives tested for hanging drop culture, MethoCel provided the most desirable spheroid formation. Additionally, the higher viscosity of MethoCel-containing media improved the ease of imaging of cellular spheroids within hanging drop cultures by reducing motion-induced image blur.

Comparison of spring-loaded, loss of resistance and hanging drop techniques in lumbar epidural blocks.

Science.gov (United States)

Gülen, Güven; Akkaya, Taylan; Ozkan, Derya; Kaydul, Mehmet; Gözaydin, Orhan; Gümüş, Haluk

2012-01-01

The spring-loaded syringe is a loss of resistance syringe that provide a more objective sign that the epidural space has been entered compared with the traditional techniques. The aim of this study was to compare the time required to locate the epidural space and the backache incidence with the spring-loaded (SL), loss of resistance (LOR) and the hanging drop (HD) techniques for epidural blocks in patients undergoing transurethral resection procedure. Sixty patients undergoing transurethral resections were enrolled in the study. The patients were randomly assigned to one of three groups. Epidural block was performed in the first group with a spring-loaded syringe (n=20), in the second group with loss-of-resistance syringe (n=20), and in the third group with the hanging drop technique (n=20). The required time to locate the epidural space, the number of attempts, the incidence of dural puncture and the backache incidence were assessed during the procedure and for four weeks after the procedure in all patients. The required time to locate the epidural space was 29.1 ± 9.16 seconds in Group 1; 45.25 ± 19.58 seconds in Group 2, and 47.35 ± 11.42 seconds in Group 3 (p0.05). The use of SL syringe was found to have a shorter time period to locate the epidural space when compared with the LOR syringe and hanging drop technique.

Interim rock mass properties and conditions for analyses of a repository in crystalline rock

International Nuclear Information System (INIS)

Tammemagi, H.Y.; Chieslar, J.D.

1985-03-01

A summary of rock properties for generic crystalline rock is compiled from literature sources to provide the input data for analyses of a conceptual repository in crystalline rock. Frequency histograms, mean values and ranges of physical, mechanical, thermal, and thermomechanical properties, and the dependence of these properties on temperature are described. A description of the hydrogeologic properties of a crystalline rock mass and their dependence on depth is provided. In addition, the temperature gradients, mean annual surface temperature, and in situ stress conditions are summarized for the three regions of the United States currently under consideration to host a crystalline repository; i.e., the North Central, Northeastern, and Southeastern. Brief descriptions of the regional geology are also presented. Large-scale underground experiments in crystalline rock at Stripa, Sweden, and in Climax Stock in Nevada, are reviewed to assess whether the rock properties presented in this report are representative of in situ conditions. The suitability of each rock property and the sufficiency of its data base are described. 110 refs., 27 figs., 4 tabs

Relative Permeability of Fractured Rock

Energy Technology Data Exchange (ETDEWEB)

Mark D. Habana

2002-06-30

Contemporary understanding of multiphase flow through fractures is limited. Different studies using synthetic fractures and various fluids have yielded different relative permeability-saturation relations. This study aimed to extend the understanding of multiphase flow by conducting nitrogen-water relative permeability experiments on a naturally-fractured rock from The Geysers geothermal field. The steady-state approach was used. However, steady state was achieved only at the endpoint saturations. Several difficulties were encountered that are attributed to phase interference and changes in fracture aperture and surface roughness, along with fracture propagation/initiation. Absolute permeabilities were determined using nitrogen and water. The permeability values obtained change with the number of load cycles. Determining the absolute permeability of a core is especially important in a fractured rock. The rock may change as asperities are destroyed and fractures propagate or st rain harden as the net stresses vary. Pressure spikes occurred in water a solute permeability experiments. Conceptual models of an elastic fracture network can explain the pressure spike behavior. At the endpoint saturations the water relative permeabilities obtained are much less than the nitrogen gas relative permeabilities. Saturations were determined by weighing and by resistivity calculations. The resistivity-saturation relationship developed for the core gave saturation values that differ by 5% from the value determined by weighing. Further work is required to complete the relative permeability curve. The steady-state experimental approach encountered difficulties due to phase interference and fracture change. Steady state may not be reached until an impractical length of time. Thus, unsteady-state methods should be pursued. In unsteady-state experiments the challenge will be in quantifying rock fracture change in addition to fluid flow changes.

Preliminary assessment of shales and other argillaceous rocks in the United States

International Nuclear Information System (INIS)

Gonzales, S.; Johnson, K.S.

1981-01-01

Shales and related clay-rich rock types throughout the conterminous United States are geologically characterized and evaluated on a regional basis relative to their promise as possible candidate rock sequences for the repository disposal of high-level radioactive wastes. Only stratigraphic intervals or parts of them that are laterally persistent, consist of 75 m or more of shale, mudstone, or argillite, and lie at depths of 305 to 915 m below the land surface are included. The general properties of clay-rich rocks, as well as the several desirable characteristics that make them potentially attractive as disposal host candidates, are reviewed. Also discussed are the geologic factors that dictate the potential acceptability of any shale sequence relative to the regional subsurface distribution of units that meet the basic criteria of extent, thickness, and depth. Included in this context are the tectonic setting, geologic structure, seismicity, groundwater hydrology, mineralogy and content of organic matter, mineral resource potential of both the shales and the enclosing geologic basins, and any construction experience on underground openings, such as hydrocarbon-storage facilities. The clay-rich strata that appear to be promising on the basis of this evaluation are inventoried according to their occurrence and distribution within nine geologic-geomorphic regions throughout the country. Also considered are several, more localized occurrences of Precambrian argillites whose mineralogies make them a related yet separate group in comparison with the sedimentary strata already summarized. Topics for which data are insufficient or on which inadequate study has been conducted to date are also identified

Simulation of rock deformation behavior

Directory of Open Access Journals (Sweden)

Я. И. Рудаев

2016-12-01

Full Text Available A task of simulating the deformation behavior of geomaterials under compression with account of over-extreme branch has been addressed. The physical nature of rock properties variability as initially inhomogeneous material is explained by superposition of deformation and structural transformations of evolutionary type within open nonequilibrium systems. Due to this the description of deformation and failure of rock is related to hierarchy of instabilities within the system being far from thermodynamic equilibrium. It is generally recognized, that the energy function of the current stress-strain state is a superposition of potential component and disturbance, which includes the imperfection parameter accounting for defects not only existing in the initial state, but also appearing under load. The equation of state has been obtained by minimizing the energy function by the order parameter. The imperfection parameter is expressed through the strength deterioration, which is viewed as the internal parameter of state. The evolution of strength deterioration has been studied with the help of Fokker – Planck equation, which steady form corresponds to rock statical stressing. Here the diffusion coefficient is assumed to be constant, while the function reflecting internal sliding and loosening of the geomaterials is assumed as an antigradient of elementary integration catastrophe. Thus the equation of state is supplemented with a correlation establishing relationship between parameters of imperfection and strength deterioration. While deformation process is identified with the change of dissipative media, coupled with irreversible structural fluctuations. Theoretical studies are proven with experimental data obtained by subjecting certain rock specimens to compression.

Colony, hanging drop, and methylcellulose three dimensional hypoxic growth optimization of renal cell carcinoma cell lines.

Science.gov (United States)

Matak, Damian; Brodaczewska, Klaudia K; Lipiec, Monika; Szymanski, Łukasz; Szczylik, Cezary; Czarnecka, Anna M

2017-08-01

Renal cell carcinoma (RCC) is the most lethal of the common urologic malignancies, comprising 3% of all human neoplasms, and the incidence of kidney cancer is rising annually. We need new approaches to target tumor cells that are resistant to current therapies and that give rise to recurrence and treatment failure. In this study, we focused on low oxygen tension and three-dimensional (3D) cell culture incorporation to develop a new RCC growth model. We used the hanging drop and colony formation methods, which are common in 3D culture, as well as a unique methylcellulose (MC) method. For the experiments, we used human primary RCC cell lines, metastatic RCC cell lines, human kidney cancer stem cells, and human healthy epithelial cells. In the hanging drop assay, we verified the potential of various cell lines to create solid aggregates in hypoxic and normoxic conditions. With the semi-soft agar method, we also determined the ability of various cell lines to create colonies under different oxygen conditions. Different cell behavior observed in the MC method versus the hanging drop and colony formation assays suggests that these three assays may be useful to test various cell properties. However, MC seems to be a particularly valuable alternative for 3D cell culture, as its higher efficiency of aggregate formation and serum independency are of interest in different areas of cancer biology.

Hanging drop crystal growth apparatus

Science.gov (United States)

Naumann, Robert J. (Inventor); Witherow, William K. (Inventor); Carter, Daniel C. (Inventor); Bugg, Charles E. (Inventor); Suddath, Fred L. (Inventor)

1990-01-01

This invention relates generally to control systems for controlling crystal growth, and more particularly to such a system which uses a beam of light refracted by the fluid in which crystals are growing to detect concentration of solutes in the liquid. In a hanging drop apparatus, a laser beam is directed onto drop which refracts the laser light into primary and secondary bows, respectively, which in turn fall upon linear diode detector arrays. As concentration of solutes in drop increases due to solvent removal, these bows move farther apart on the arrays, with the relative separation being detected by arrays and used by a computer to adjust solvent vapor transport from the drop. A forward scattering detector is used to detect crystal nucleation in drop, and a humidity detector is used, in one embodiment, to detect relative humidity in the enclosure wherein drop is suspended. The novelty of this invention lies in utilizing angular variance of light refracted from drop to infer, by a computer algorithm, concentration of solutes therein. Additional novelty is believed to lie in using a forward scattering detector to detect nucleating crystallites in drop.

State of the art of numerical modeling of thermohydrologic flow in fractured rock mass

International Nuclear Information System (INIS)

Wang, J.S.Y.; Tsang, C.F.; Sterbentz, R.A.

1983-01-01

The state of the art of numerical modeling of thermohydrologic flow in fractured rock masses is reviewed and a comparative study is made of several models which have been developed in nuclear waste isolation, geothermal energy, ground-water hydrology, petroleum engineering, and other geologic fields. The general review is followed by separate summaries of the main characteristics of the governing equations, numerical solutions, computer codes, validations, and applications for each model

An autopsy study of death due to Suicidal Hanging – 264 cases

Directory of Open Access Journals (Sweden)

Dinesh Rao

2016-09-01

Full Text Available The present study was carried out between 2010 and 2013, a total of 7968 Autopsies were conducted of which 3.31% (n – 264 cases were deaths due to hanging. The most preferred ligature materials were Stole (n – 79 and Bed spread/Sari (n – 68. In 88% of the cases, hanging was complete. Females (n – 136 and males (n – 128 were equally affected. The major age group involved in both the sexes was of 31–40 years, contributing to 50.76% (n – 136 of the self suspension. In 80.58% (n – 213 of the incidents, ligature mark showed discontinuity (incomplete. A Slip type of knot was used in majority of the noose, contributing to 97.73% (n – 258 of the suspensions. In 87.88% (n – 232 of hanging an oblique shaped ligature mark was noticed. The horizontal and near oblique ligature marks were seen only in cases of partial suspension. In 95.45% (n – 252 of the cases, the ligature mark showed blackening of the skin (friction burn. Only 4.54% (n – 12 showed intact skin. The outer layer of the skin over the ligature mark showed displacement in majority of the cases. Married victims contributed to 70.45% of cases. Domestic issues were the commonest reason (n – 82 for self suspension, of which female (n – 68 formed the majority of victims. In 70.83% (n – 187 of cases damage to neck muscle fibers and hemorrhage at the Sternal end of the Sternocleidomastoid muscle were present. In 85.61% (n – 226 of cases the cervical vertebra was intact. In 52.27% (n – 138 of the cases the internal carotid artery showed transverse tear. In 99.42% (n – 248 cases the thyroid cartilage was found intact. The hyoid bone was damaged in 6.06% (n – 16 of the victims. Majority of the victims, 59.09% (n – 156 belonged to low socioeconomic class.

Enhanced differentiation of human embryonic stem cells into cardiomyocytes by combining hanging drop culture and 5-azacytidine treatment.

Science.gov (United States)

Yoon, Byung Sun; Yoo, Seung Jun; Lee, Jeoung Eun; You, Seungkwon; Lee, Hoon Taek; Yoon, Hyun Soo

2006-04-01

Cell replacement therapy is a promising approach for the treatment of cardiac diseases. It is, however, challenged by a limited supply of appropriate cells. Therefore, we have investigated whether functional cardiomyocytes can be efficiently generated from human embryonic stem cells (hESCs). In this study, we developed an efficient protocol for the generation of functional cardiomyocytes from hESCs by combining hanging drop culture and 5-azacytidine, a well-known demethylating agent, and then evaluated the expression of cardiac-specific markers. hESCs were cultured both in the medium without or with 0.1, 1, or 10 microM of 5-azacytidine under a hanging drop culture. The expression of several cardiac-specific markers was determined by real-time PCR, RT-PCR, immunofluorescence, and confocal microscopy. To verify the structural and functional properties of hESC-derived cardiomyocytes, we performed electron microscopy and electrophysiological recording. The efficiency of beating cell generation was significantly improved in the hanging drop culture compared with that in suspension culture. Treatment of hESCs with 0.1 microM of 5-azacytidine for 1-3 days significantly increased the number of beating cells and simultaneously enhanced the expression of cardiac-specific markers. Transmission electron microscopy and electrophysiological recording showed that hESC-derived cardiomyocytes acquired structural and functional properties of cardiomyocytes. In conclusion, these results suggest that differentiation of hESCs into cardiomyocytes can be enhanced by the combination of hanging drop culture and 5-azacytidine treatment. Also the methylation status of genes related to cardiomyocyte development may play an important role in the differentiation of hESCs into cardiomyocytes.

3D Hanging Drop Culture to Establish Prostate Cancer Organoids.

Science.gov (United States)

Eder, Theresa; Eder, Iris E

2017-01-01

Three-dimensional (3D) cell culture enables the growth of cells in a multidimensional and multicellular manner compared to conventional cell culture techniques. Especially in prostate cancer research there is a big need for more tissue-recapitulating models to get a better understanding of the mechanisms driving prostate cancer as well as to screen for more efficient drugs that can be used for treatment. In this chapter we describe a 3D hanging drop system that can be used to culture prostate cancer organoids as tumor epithelial monocultures and as epithelial-stromal cocultures.

Petrological and geochemical studies of alkaline rocks from continental Brazil. The tunas massif, state of Parana

International Nuclear Information System (INIS)

Gomes, C.B.; Barbieri, M.

1987-01-01

The Tunas massif, outcropping 80 km from the city of Curitiba, Parana State, southern Brazil, covers about 22 km 2 . It intruded into Precambrian metaigneous and metasedimentary units about 80 Ma ago (K/Ar and Rb/Sr data); five subcircular volcanic structures are recognized. Syenites and alkali syenites (plus some pulaskites) are the main rock-types, with subordinate alkali gabbros, syenogabbros, essexites and syenodiorites; small late syenitic dikes are also found. Magmatic breccias containing clasts of all rock-types are widespread. Main minerals are feldspars (both alkali feldspars and plagioclases, varying from bytownite to more sodic members), Ca-pyroxenes (Ti-salites grading towards ferrosalites and aegirine-augites), amphiboles (mainly pargasites, although kaersutites and katophorites are also present), Fe-biotites (sometimes enriched in Ti), olivines (hortonolites to ferrohortonolites), quartz and feldspathoids (both fresh and altered nephelines and sodalites); main accessories are Ti-magnetites (with exsolved ilmenite) and apatite. In the AFM diagram, whole rock chemistry depicts a typical alkaline trend. Binary variation diagrams (D.I. vs. several elements) show positive correlation for Si, Na and K, and negative slopes for Mg and Ca. The variation in the amounts of Ni, Cr and V with differentiation can be explained by withdrawal of olivine, Ca-pyroxenes and magnetite, and that of Sr and Ba by the fractionation of feldspars. The rocks are also relatively enriched in REE, a trend which is more pronounced for the light REE. Mass balance calculations show that the overall differentiation trend of the Tunas rocks can be explained by crystal fractionation, although several complexities arise and point to more complex genetic patterns. Isotopic Rb/Sr ratios are consistent with a mantle origin for the parental magma; dike rocks, however, with 87 Sr 86 Sr i = 0.70777 - 0.70806, were probably contaminated by crustal material. (author) [pt

Hanging colloidal drop: A new photonic crystal synthesis route

Science.gov (United States)

Sandu, Ion; Dumitru, Marius; Fleaca, Claudiu Teodor; Dumitrache, Florian

2018-05-01

High-quality photonic crystals (hundreds of micrometres in thickness) were grown by the free evaporation of a colloidal drop consisting of silica and polystyrene nanospheres with dimensions of 300 nm, 500 nm, and 1000 nm. The essence of experimental findings is that the drop has to hang on a pillar. This leads to the inhibition of the droplet spreading, the minimisation of the convective force, and the zeroing of the static frictional force between nanospheres and the liquid/air interface, where the first layer is formed. The theoretical essence is the continuous adjustment of nanospheres positions during the growth of photonic crystal, a key condition of the self-assembling phenomenon.

Measurement of the mass of an object hanging from a spring—revisited

International Nuclear Information System (INIS)

Serafin, Kamil; Oracz, Joanna; Grzybowski, Marcin; Koperski, Maciej; Sznajder, Paweł; Zinkiewicz, Łukasz; Wasylczyk, Piotr

2012-01-01

In an open competition, students were to determine the mass of a metal cylinder hanging on a spring inside a transparent enclosure. With the time for experiments limited to 24 h due to the unexpectedly large number of participants, a few surprisingly accurate results were submitted, the best of them differing by no more than 0.5% from the true value with a relative uncertainty of less than 1%.

Kimberlite Wall Rock Fragmentation: Venetia K08 Pipe Development

Science.gov (United States)

Barnett, W.; Kurszlaukis, S.; Tait, M.; Dirks, P.

2009-05-01

Volcanic systems impose powerful disrupting forces on the country rock into which they intrude. The nature of the induced brittle deformation or fragmentation can be characteristic of the volcanic processes ongoing within the volcanic system, but are most typically partially removed or obscured by repeated, overprinting volcanic activity in mature pipes. Incompletely evolved pipes may therefore provide important evidence for the types and stages of wall rock fragmentation, and mechanical processes responsible for the fragmentation. Evidence for preserved stages of fragmentation is presented from a detailed study of the K08 pipe within the Cambrian Venetia kimberlite cluster, South Africa. This paper investigates the growth history of the K08 pipe and the mechanics of pipe development based on observations in the pit, drill core and thin sections, from geochemical analyses, particle size distribution analyses, and 3D modeling. Present open pit exposures of the K08 pipe comprise greater than 90% mega-breccia of country rock clasts (gneiss and schist) with Drill core shows that below about 225 m the CRB includes increasing quantities of kimberlite. The breccia clasts are angular, clast-supported with void or carbonate cement between the clasts. Average clast sizes define sub-horizontal layers tens of metres thick across the pipe. Structural and textural observations indicate the presence of zones of re-fragmentation or zones of brittle shearing. Breccia textural studies and fractal statistics on particle size distributions (PSD) is used to quantify sheared and non- sheared breccia zones. The calculated energy required to form the non-sheared breccia PSD implies an explosive early stage of fragmentation that pre-conditions the rock mass. The pre-conditioning would have been caused by explosions that are either phreatic or phreatomagmatic in nature. The explosions are likely to have been centered on a dyke, or pulses of preceding volatile-fluid phases, which have

On-line mass spectrometry system for measurements at single-crystal electrodes in hanging meniscus configuration

NARCIS (Netherlands)

Wonders, A.H.; Housmans, T.H.M.; Rosca, V.; Koper, M.T.M.

2006-01-01

We present the construction and some first applications of an On-line electrochemical mass spectrometry system for detecting volatile products formed during electrochemical reactions at a single-crystal electrode in hanging meniscus configuration. The system is based on a small inlet tip made of

SU-F-T-75: Dosimetry Considerations in the Use of Hanging-Eye Block for Lesions of the Conjunctiva

Energy Technology Data Exchange (ETDEWEB)

Grelewicz, Z; Lee, B; Cutright, D; Kang, Z; Gopalakrishnan, M; Sathiaseelan, V; Zhang, H [Northwestern Memorial Hospital, Chicago, IL (United States)

2016-06-15

Purpose: Superficial lesions in the conjunctiva are frequently treated with en face electrons, using a hanging block to spare dose to the lens of the eye. Dose to the tumor and lens depend on the design and setup of the block and supporting apparatus. We performed in phantom measurements in order to characterize the dose sparing effects of the block as well as the under-dosing effect under the supporting apparatus for 6 MeV treatment. Methods: The commercial hanging block studied uses a 1.2 cm diameter tungsten cylinder supported by a 3 mm diameter acrylic rod. Point dose measurements under the hanging block, under an unblocked part of the field, and under the acrylic rod were performed using MOSFET detectors. In addition, EBT3 film was used for both PDD and profile measurements at a depth in phantom of 3 mm for both 105 and 103 cm SSD. Results: MOSFET measurements reported a dose reduction of 95% under the tungsten block when using an SSD of 103 cm, and 86% when using an SSD of 105 cm at a depth in phantom of 3 mm. Film measurements showed that the area under the acrylic rod may be under-dosed by as much as 30% when using 103 SSD. MOSFET measurements confirmed that when using an SSD of 103 cm, the area under the acrylic rod is under-dosed by up to 30% at 3mm depth, compared to the unblocked part of the field. Conclusion: The effectiveness of the commercial hanging block apparatus depends on setup, with 95% lens sparing possible with an SSD of 103 cm. This short SSD is necessary for sharp penumbra. At this SSD, substantial under-dosing under the acrylic support rod is possible. This must be mitigated with either feathering, or using an alternative method of support for the tungsten block.

Redifferentiation of in vitro expanded adult articular chondrocytes by combining the hanging-drop cultivation method with hypoxic environment.

Science.gov (United States)

Martinez, Inigo; Elvenes, Jan; Olsen, Randi; Bertheussen, Kjell; Johansen, Oddmund

2008-01-01

The main purpose of this work has been to establish a new culturing technique to improve the chondrogenic commitment of isolated adult human chondrocytes, with the aim of being used during cell-based therapies or tissue engineering strategies. By using a rather novel technique to generate scaffold-free three-dimensional (3D) structures from in vitro expanded chondrocytes, we have explored the effects of different culture environments on cartilage formation. Three-dimensional chondrospheroids were developed by applying the hanging-drop technique. Cartilage tissue formation was attempted after combining critical factors such as serum-containing or serum-free media and atmospheric (20%) or low (2.5%) oxygen tensions. The quality of the formed microtissues was analyzed by histology, immunohistochemistry, electron microscopy, and real-time PCR, and directly compared with native adult cartilage. Our results revealed highly organized, 3D tissue-like structures developed by the hanging-drop method. All culture conditions allowed formation of 3D spheroids; however, cartilage generated under low oxygen tension had a bigger size, enhanced matrix deposition, and higher quality of cartilage formation. Real-time PCR demonstrated enhanced expression of cartilage-specific genes such us collagen type II and aggrecan in 3D cultures when compared to monolayers. Cartilage-specific matrix proteins and genes expressed in hanging-drop-developed spheroids were comparable to the expression obtained by applying the pellet culture system. In summary, our results indicate that a combination of 3D cultures of chondrocytes in hanging drops and a low oxygen environment represent an easy and convenient way to generate cartilage-like microstructures. We also show that a new specially tailored serum-free medium is suitable for in vitro cartilage tissue formation. This new methodology opens up the possibility of using autogenously produced solid 3D structures with redifferentiated chondrocytes as an

Extending total parenteral nutrition hang time in the neonatal intensive care unit: is it safe and cost effective?

Science.gov (United States)

Balegar V, Kiran Kumar; Azeem, Mohammad Irfan; Spence, Kaye; Badawi, Nadia

2013-01-01

To investigate the effects of prolonging hang time of total parenteral nutrition (TPN) fluid on central line-associated blood stream infection (CLABSI), TPN-related cost and nursing workload. A before-after observational study comparing the practice of hanging TPN bags for 48 h (6 February 2009-5 February 2010) versus 24 h (6 February 2008-5 February 2009) in a tertiary neonatal intensive care unit was conducted. The main outcome measures were CLABSI, TPN-related expenses and nursing workload. One hundred thirty-six infants received 24-h TPN bags and 124 received 48-h TPN bags. Median (inter-quartile range) gestation (37 weeks (33,39) vs. 36 weeks (33,39)), mean (±standard deviation) admission weight of 2442 g (±101) versus 2476 g (±104) and TPN duration (9.7 days (±12.7) vs. 9.9 days (±13.4)) were similar (P > 0.05) between the 24- and 48-h TPN groups. There was no increase in CLABSI with longer hang time (0.8 vs. 0.4 per 1000 line days in the 24-h vs. 48-h group; P < 0.05). Annual cost saving using 48-h TPN was AUD 97,603.00. By using 48-h TPN, 68.3% of nurses indicated that their workload decreased and 80.5% indicated that time spent changing TPN reduced. Extending TPN hang time from 24 to 48 h did not alter CLABSI rate and was associated with a reduced TPN-related cost and perceived nursing workload. Larger randomised controlled trials are needed to more clearly delineate these effects. © 2012 The Authors. Journal of Paediatrics and Child Health © 2012 Paediatrics and Child Health Division (Royal Australasian College of Physicians).

Creep in jointed rock masses. State of knowledge

Energy Technology Data Exchange (ETDEWEB)

Glamheden, Rune (Golder Associates AB (Sweden)); Hoekmark, Harald (Clay Technology AB, Lund (Sweden))

2010-06-15

To describe creep behaviour in hard rock masses in a physically realistic way, elaborate models including various combinations of dash pots, spring elements and sliders would be needed. According to our knowledge, there are at present no numerical tools available that can handle such a creep model. In addition, there are no records over sufficient long time periods of tunnel convergence in crystalline rock that could be used to determine or calibrate values for the model parameters. A possible method to perform bounding estimates of creep movements around openings in a repository may be to use distinct element codes with standard built-in elasto-plastic models. By locally reducing the fracture shear strength near the underground openings a relaxation of fracture shear loads is reached. The accumulated displacements may then represent the maximum possible effects of creep that can take place in a jointed rock mass without reference to the actual time it takes to reach the displacements. Estimates based on results from analyses where all shear stresses are allowed to disappear completely will, however, be over-conservative. To be able to set up and analyse reasonably realistic numerical models with the proposed method, further assumptions regarding the creep movements and the creep region around the opening have to be made. The purpose of this report is to present support for such assumptions as found in the literature.

Creep in jointed rock masses. State of knowledge

International Nuclear Information System (INIS)

Glamheden, Rune; Hoekmark, Harald

2010-06-01

To describe creep behaviour in hard rock masses in a physically realistic way, elaborate models including various combinations of dash pots, spring elements and sliders would be needed. According to our knowledge, there are at present no numerical tools available that can handle such a creep model. In addition, there are no records over sufficient long time periods of tunnel convergence in crystalline rock that could be used to determine or calibrate values for the model parameters. A possible method to perform bounding estimates of creep movements around openings in a repository may be to use distinct element codes with standard built-in elasto-plastic models. By locally reducing the fracture shear strength near the underground openings a relaxation of fracture shear loads is reached. The accumulated displacements may then represent the maximum possible effects of creep that can take place in a jointed rock mass without reference to the actual time it takes to reach the displacements. Estimates based on results from analyses where all shear stresses are allowed to disappear completely will, however, be over-conservative. To be able to set up and analyse reasonably realistic numerical models with the proposed method, further assumptions regarding the creep movements and the creep region around the opening have to be made. The purpose of this report is to present support for such assumptions as found in the literature

Sizing of colloidal particle and protein molecules in a hanging fluid drop

Science.gov (United States)

Ansari, Rafat R.; Suh, Kwang I.

1995-01-01

We report non-invasive particle size measurements of polystyrene latex colloidal particles and bovine serum albumin (BSA) protein molecules suspended in tiny hanging fluid drops of 30 micro-Liter volume using a newly designed fiber optic probe. The probe is based upon the principles of the technique of dynamic light scattering (DLS). The motivation for this work comes from growing protein crystals in outer space. Protein crystals have been grown previously in hanging drops in microgravity experiments on-board the space shuttle orbiter. However, obtaining quantitative information on nucleation and growth of the protein crystals in real time has always been a desired goal, but hitherto not achieved. Several protein researchers have shown interest in using DLS to monitor crystal growth process in a droplet, but elaborate instrumentation and optical alignment problems have made in-situ applications difficult. We demonstrate that such an experiment is now possible. Our system offers fast (5 seconds) determination of particle size, utilize safe levels of very low laser power (less than or equal to 0.2 mW), a small scattering volume (approximately 2 x 10(exp -5) cu mm) and high spatial coherence (Beta) values. This is a major step forward when compared to currently available DLS systems.

Response of rocks to large stresses

International Nuclear Information System (INIS)

Schock, R.N.

1976-01-01

To predict the dimensions and characteristics of impact- and explosion-induced craters, one must know the equation of state of the rocks in which the crater is formed. Recent experimental data shed light upon inelastic processes that influence the stress/strain behavior of rocks. We examine these data with a view to developing models that could be used in predicting cratering phenomena. New data is presented on the volume behavior of two dissimilar rocks subjected to tensile stresses

Thermally induced rock stress increment and rock reinforcement response

International Nuclear Information System (INIS)

Hakala, M.; Stroem, J.; Nujiten, G.; Uotinen, L.; Siren, T.; Suikkanen, J.

2014-07-01

This report describes a detailed study of the effect of thermal heating by the spent nuclear fuel containers on the in situ rock stress, any potential rock failure, and associated rock reinforcement strategies for the Olkiluoto underground repository. The modelling approach and input data are presented together repository layout diagrams. The numerical codes used to establish the effects of heating on the in situ stress field are outlined, together with the rock mass parameters, in situ stress values, radiogenic temperatures and reinforcement structures. This is followed by a study of the temperature and stress evolution during the repository's operational period and the effect of the heating on the reinforcement structures. It is found that, during excavation, the maximum principal stress is concentrated at the transition areas where the profile changes and that, due to the heating from the deposition of spent nuclear fuel, the maximum principal stress rises significantly in the tunnel arch area of NW/SW oriented central tunnels. However, it is predicted that the rock's crack damage (CD, short term strength) value of 99 MPa will not be exceeded anywhere within the model. Loads onto the reinforcement structures will come from damaged and loosened rock which is assumed in the modelling as a free rock wedge - but this is very much a worst case scenario because there is no guarantee that rock cracking would form a free rock block. The structural capacity of the reinforcement structures is described and it is predicted that the current quantity of the rock reinforcement is strong enough to provide a stable tunnel opening during the peak of the long term stress state, with damage predicted on the sprayed concrete liner. However, the long term stability and safety can be improved through the implementation of the principles of the Observational Method. The effect of ventilation is also considered and an additional study of the radiogenic heating effect on the brittle

Thermally induced rock stress increment and rock reinforcement response

Energy Technology Data Exchange (ETDEWEB)

Hakala, M. [KMS Hakala Oy, Nokia (Finland); Stroem, J.; Nujiten, G.; Uotinen, L. [Rockplan, Helsinki (Finland); Siren, T.; Suikkanen, J.

2014-07-15

This report describes a detailed study of the effect of thermal heating by the spent nuclear fuel containers on the in situ rock stress, any potential rock failure, and associated rock reinforcement strategies for the Olkiluoto underground repository. The modelling approach and input data are presented together repository layout diagrams. The numerical codes used to establish the effects of heating on the in situ stress field are outlined, together with the rock mass parameters, in situ stress values, radiogenic temperatures and reinforcement structures. This is followed by a study of the temperature and stress evolution during the repository's operational period and the effect of the heating on the reinforcement structures. It is found that, during excavation, the maximum principal stress is concentrated at the transition areas where the profile changes and that, due to the heating from the deposition of spent nuclear fuel, the maximum principal stress rises significantly in the tunnel arch area of NW/SW oriented central tunnels. However, it is predicted that the rock's crack damage (CD, short term strength) value of 99 MPa will not be exceeded anywhere within the model. Loads onto the reinforcement structures will come from damaged and loosened rock which is assumed in the modelling as a free rock wedge - but this is very much a worst case scenario because there is no guarantee that rock cracking would form a free rock block. The structural capacity of the reinforcement structures is described and it is predicted that the current quantity of the rock reinforcement is strong enough to provide a stable tunnel opening during the peak of the long term stress state, with damage predicted on the sprayed concrete liner. However, the long term stability and safety can be improved through the implementation of the principles of the Observational Method. The effect of ventilation is also considered and an additional study of the radiogenic heating effect on the

Formation and evolution of mesozoic volcanic basins in Gan-Hang tectonic belt

International Nuclear Information System (INIS)

Zhang Xingpu

1999-01-01

The author mainly discusses the principle model for the formation and the evolution of Mesozoic volcanic basins in the Gan-Hang Tectonic Belt, and describes the distinct evolution features between the internal and external sites of volcanic basins, the natural relation between the down-warped, down-faulted, collapse volcanic basins and volcanic domes, the relationship between the formation of inter layered fractured zones of the volcanic cover and the evolution of volcanic basins

Detrended cross-correlation analysis on RMB exchange rate and Hang Seng China Enterprises Index

Science.gov (United States)

Ruan, Qingsong; Yang, Bingchan; Ma, Guofeng

2017-02-01

In this paper, we investigate the cross-correlations between the Hang Seng China Enterprises Index and RMB exchange markets on the basis of a cross-correlation statistic test and multifractal detrended cross-correlation analysis (MF-DCCA). MF-DCCA has, at best, serious limitations for most of the signals describing complex natural processes and often indicates multifractal cross-correlations when there are none. In order to prevent these false multifractal cross-correlations, we apply MFCCA to verify the cross-correlations. Qualitatively, we find that the return series of the Hang Seng China Enterprises Index and RMB exchange markets were, overall, significantly cross-correlated based on the statistical analysis. Quantitatively, we find that the cross-correlations between the stock index and RMB exchange markets were strongly multifractal, and the multifractal degree of the onshore RMB exchange markets was somewhat larger than the offshore RMB exchange markets. Moreover, we use the absolute return series to investigate and confirm the fact of multifractality. The results from the rolling windows show that the short-term cross-correlations between volatility series remain high.

Review of potential host rocks for radioactive waste disposal in the southeast United States-Southern Piedmont subregion

International Nuclear Information System (INIS)

1980-10-01

A literature study was conducted on the geology of the Southern Piedmont province in the states of Maryland, Virginia, North Carolina, South Carolina, and Georgia. The purpose was to identify geologic areas potentially suitable for containment of a repository for the long-term isolation of solidified radioactive waste. The crystalline rocks of the Southern Piedmont province range in age from Precambrian to Paleozoic, and are predominantly slates, phyllites, argillites, schists, metavolcanics, gneisses, gabbros, and granites. These rock units were classified as either favorable, potentially favorable, or unfavorable as potential study areas based on an evaluation of the geologic, hydrologic, and geotechnical characteristics. No socio-economic factors were considered. Rocks subjected to multiple periods of deformation and metamorphism, or described as highly fractured, or of limited areal extent were generally ranked as unfavorable. Potentially favorable rocks are primarily the high-grade metamorphic gneisses and granites. Sixteen areas were classified as being favorable for additional study. These areas are primarily large igneous granite plutons as follows: the Petersburg granite in Virginia; the Rolesville-Castallia, Churchland, and Landis plutons in North Carolina; the Liberty Hill, Winnsboro, and Ogden plutons in South Carolina; and the Siloam, Elberton, and six unnamed granite plutons in Georgia

Flutter instability of freely hanging articulated pipes conveying fluid

Science.gov (United States)

Schouveiler, Lionel; Chermette, Félix

2018-03-01

We experimentally investigate the stability of freely hanging articulated pipes made of rigid segments connected by flexible joints and with their displacements constrained in a vertical plane. When the velocity of the fluid conveyed by the pipe is increased, flutter-type instability occurs above a critical value. The critical velocity and the characteristics of the flutter modes (frequency, amplitude, and shape) are determined as a function of the number n of segments into the pipe which is varied from 2 to 5. Experimental results are compared to predictions from linear stability analysis extending previous studies by taking into account damping due to the dissipation in the joints. Qualitative agreement is found and the limits of the analysis are discussed.

Hanging out at the airport: Unusual upside-down perching behavior by Eurasian Jackdaws (Corvus monedula) in a human-dominated environment

Science.gov (United States)

Katzner, Todd E.

2016-01-01

Animals occupying human-dominated environments show the capacity for behavioral flexibility. Corvids are among the most intelligent synanthropic bird species. During a layover at Schipol Airport in Amsterdam, Netherlands, I photographically documented Eurasian Jackdaws (Corvus monedula) perching upside down from a building cornice. In contrast to other reports of hanging birds, these jackdaws did not forage or play while upside down and appeared to use the perching spot to observe their surroundings. Although Corvids and Psittacines are known to hang upside down, especially in captive situations, such behaviors are rarely documented in the wild, and never before in association with human-built structures.

The state of the art of numerical modeling of thermohydrologic flow in fractured rock masses

International Nuclear Information System (INIS)

Wang, J.S.Y.; Sterbentz, R.A.; Tsang, C.F.

1982-01-01

The state of the art of numerical modeling of thermohydrologic flow in fractured rock masses is reviewed and a comparative study is made of several models which have been developed in nuclear waste isolation, geothermal energy, ground water hydrology, petroleum engineering, and other geologic fields. The general review is followed by individual summaries of each model and the main characteristics of its governing equations, numerical solutions, computer codes, validations, and applications

Assessment of natural radioactivity levels in rocks and their relationships with the geological structure of Johor state, Malaysia.

Science.gov (United States)

Alnour, I A; Wagiran, H; Ibrahim, N; Hamzah, S; Elias, M S; Laili, Z; Omar, M

2014-01-01

The distribution of natural radionuclides ((238)U, (232)Th and (40)K) and their radiological hazard effect in rocks collected from the state of Johor, Malaysia were determined by gamma spectroscopy using a high-purity germanium detector. The highest values of (238)U, (232)Th and (40)K activity concentrations (67±6, 85±7 and 722±18 Bg kg(-1), respectively) were observed in the granite rock. The lowest concentrations of (238)U and (232)Th (2±0.1 Bq kg(-1) for (238)U and 2±0.1 Bq kg(-1) for (232)Th) were observed in gabbro rock. The lowest concentration of (40)K (45±2 Bq kg(-1)) was detected in sandstone. The radium equivalent activity concentrations for all rock samples investigated were lower than the internationally accepted value of 370 Bq kg(-1). The highest value of radium equivalent in the present study (239±17 Bq kg(-1)) was recorded in the area of granite belonging to an acid intrusive rock geological structure. The absorbed dose rate was found to range from 4 to 112 nGy h(-1). The effective dose ranged from 5 to 138 μSv h(-1). The internal and external hazard index values were given in results lower than unity. The purpose of this study is to provide information related to radioactivity background levels and the effects of radiation on residents in the study area under investigation. Moreover, the relationships between the radioactivity levels in the rocks within the geological structure of the studied area are discussed.

Intracellular localization of pregnane X receptor in HepG2 cells cultured by the hanging drop method.

Science.gov (United States)

Yokobori, Kosuke; Kobayashi, Kaoru; Azuma, Ikuko; Akita, Hidetaka; Chiba, Kan

2017-10-01

Pregnane X receptor (PXR) is localized in the cytoplasm of liver cells, whereas it is localized in the nucleus of monolayer-cultured HepG2 cells. Since cultured cells are affected by the microenvironment in which they are grown, we studied the effect of three-dimensional (3D) culture on the localization of PXR in HepG2 cells using the hanging drop method. The results showed that PXR was retained in the cytoplasm of HepG2 cells and other human hepatocarcinoma cell lines (FLC5, FLC7 and Huh7) when they were cultured by the hanging drop method. Treatment with rifampicin, a ligand of PXR, translocated PXR from the cytoplasm to nucleus and increased expression levels of CYP3A4 mRNA in HepG2 cells cultured by the hanging drop method. These findings suggest that 3D culture is a key factor determining the intracellular localization of PXR in human hepatocarcinoma cells and that PXR that becomes retained in the cytoplasm of HepG2 cells with 3D culture has functions of nuclear translocation and regulation of target genes in response to human PXR ligands. Three-dimensionally cultured hepatocarcinoma cells would be a useful tool to evaluate induction potency of drug candidates and also to study mechanisms of nuclear translocation of PXR by human PXR ligands. Copyright © 2017 The Japanese Society for the Study of Xenobiotics. Published by Elsevier Ltd. All rights reserved.

Cervical spine injuries in suicidal hanging without a long-drop--patterns and possible underlying mechanisms of injury: an autopsy study.

Science.gov (United States)

Nikolić, Slobodan; Zivković, Vladimir

2014-06-01

The incidence of cervical spine injuries in suicidal hangings with a short-drop has been reported to be extremely low or non-existent. The aim of this study was to determine the frequency and pattern of cervical spine injuries in suicidal hanging. A retrospective autopsy study was performed and short-drop suicidal hanging cases with documented cervical spine injuries were identified. This group was further analyzed with regard to the gender and age of the deceased, the position of the ligature knot, the presence of hyoid-laryngeal fractures, and the level of cervical spine injury. Cervical spine injuries were present in 25 of the 766 cases, with an average age of 71.9 ± 10.7 years (range 39-88 years). In 16 of these 25 cases, the ligature knot was in the anterior position. The most common pattern of cervical spine injury included partial or complete disruption of the anterior longitudinal ligament and widening of the lower cervical spine disk spaces, associated with absence of hyoid-laryngeal fractures. Cervical spine injuries are not commonly found in short-drop suicidal hanging, occurring in only 3.3 % of all observed cases. Cervical spine injury may be occurring in 80 % of subjects aged 66.5 years and above. The most common pattern of cervical spine injury included anterior longitudinal ligament disruption of the lower cervical spine, disk space widening, and no vertebral body displacement. These injuries were mainly associated with an anterior knot position, and may be a consequence of loop pressure to the posterior neck and cervical spine hyperextension.

Rehabilitation approaches to dysphagia that was developed for a patient who attempted to commit suicide by hanging: a case report.

Science.gov (United States)

Kii, Y; Mizuma, M

2014-04-01

We report our experience with a case of attempted suicidal hanging presenting with dysphagia, in which rehabilitation approaches resulted in improvement. A 36-year-old man was discovered collapsed at home. From the finding of a broken cord nearby, attempted suicide by hanging was suspected. He was transported to hospital after 40 minutes, and regained consciousness after emergency treatment. There were no noteworthy findings on brain magnetic resonance imaging, cervical spine computed tomography, or vocal cord examination. There were no noteworthy psychiatric disorders or cognitive abnormalities. On hospital day 10, he showed signs of dysphagia. Videofluoroscopic examination of swallowing revealed piriform sinuses residue and aspiration after ingestion of jelly in any posture. Rehabilitation approaches were started based on the diagnosis of dysphagia due to impaired transit through the piriform sinuses. The patient achieved independent oral intake by 40 days after the injury. In this case, dysphagia was considered attributable to compression of the vagus nerves running along the lateral aspects of the neck by the cord used in the hanging. If compression is brief, full functional recovery can be expected. Implementation of rehabilitation approaches is also important in this situation.

Creep in the sparsely fractured rock between a disposal vault and a zone of highly fractured rock

International Nuclear Information System (INIS)

Wilkins, B.J.S.; Rigby, G.L.

1993-08-01

AECL Research is responsible for investigating the feasibility and safety of the disposal of Canada's nuclear fuel waste deep in the plutonic rock of the Canadian Shield. The excavation of the disposal vault, the installation of sealing systems and the heat generated by the fuel waste will all perturb the in situ stress state of the rock mass. This computer codes HOTROK, MCROC and MCDIRC are used to analyze the influence of these stress perturbations on the mechanical behaviour of the rock mass. Time-dependent microcracking of the rock mass will lead to creep around openings in the vault. The analysis specifically estimates the resulting creep strain in the sparsely fractured rock between the edge of the disposal vault and a postulated zone of highly fractured rock. The estimates are extremely conservative. The conclusion reached is that the rock mass more than 3 m beyond the edge of the vault will experience < 0.001 creep strain 100 000 years after the fuel waste is emplaced. (author). 10 refs., 4 tabs., 4 figs

Determination of trace arsenic on hanging copper amalgam drop electrode.

Science.gov (United States)

Piech, Robert; Baś, Bogusław; Niewiara, Ewa; Kubiak, Władysław W

2007-04-30

Hanging copper amalgam drop electrode has been applied for trace determination of arsenic by cathodic stripping analysis. Detection limit for As(III) as low as 0.33nM (0.02mug/L) at deposition time (240s) could be obtained. For seven successive determinations of As(III) at concentration of 5nM relative standard deviation was 2.5% (n=7). Interferences from selected metals and surfactant substances were examined. Absence of copper ions in sample solution causes easier optimization and makes method less vulnerable on contamination. The developed method was validated by analysis of certified reference materials (CRMs) and applied to arsenic determinations in natural water samples.

Self-gated 4D multiphase, steady-state imaging with contrast enhancement (MUSIC) using rotating cartesian K-space (ROCK): Validation in children with congenital heart disease.

Science.gov (United States)

Han, Fei; Zhou, Ziwu; Han, Eric; Gao, Yu; Nguyen, Kim-Lien; Finn, J Paul; Hu, Peng

2017-08-01

To develop and validate a cardiac-respiratory self-gating strategy for the recently proposed multiphase steady-state imaging with contrast enhancement (MUSIC) technique. The proposed SG strategy uses the ROtating Cartesian K-space (ROCK) sampling, which allows for retrospective k-space binning based on motion surrogates derived from k-space center line. The k-space bins are reconstructed using a compressed sensing algorithm. Ten pediatric patients underwent cardiac MRI for clinical reasons. The original MUSIC and 2D-CINE images were acquired as a part of the clinical protocol, followed by the ROCK-MUSIC acquisition, all under steady-state intravascular distribution of ferumoxytol. Subjective scores and image sharpness were used to compare the images of ROCK-MUSIC and original MUSIC. All scans were completed successfully without complications. The ROCK-MUSIC acquisition took 5 ± 1 min, compared to 8 ± 2 min for the original MUSIC. Image scores of ROCK-MUSIC were significantly better than original MUSIC at the ventricular outflow tracts (3.9 ± 0.3 vs. 3.3 ± 0.6, P ROCK-MUSIC in the other anatomic locations. ROCK-MUSIC provided images of equal or superior image quality compared to original MUSIC, and this was achievable with 40% savings in scan time and without the need for physiologic signal. Magn Reson Med 78:472-483, 2017. © 2016 International Society for Magnetic Resonance in Medicine. © 2016 International Society for Magnetic Resonance in Medicine.

Liver hanging maneuver for right hemiliver in situ donation – anatomical considerations

OpenAIRE

Trotovšek, B.; Gadžijev, E.M.; Ravnik, D.; Hribernik, M.

2006-01-01

Background. An anatomical study was carried out to evaluate the safety of the liver hanging maneuver for the right hemiliver in living donor and in situ splitting transplantation. During this procedure a 4–6 cm blind dissection is performed between the inferior vena cava and the liver. Short subhepatic veins entering the inferior vena cava from segments 1 and 9 could be torn with consequent hemorrhage. Materials and methods. One hundred corrosive casts of livers were evaluated to establish th...

Toxicologic Laboratory Findings in Cases Reported with Hanging Death: a Two-Year Retrospective Study in Northeast Iran

Directory of Open Access Journals (Sweden)

Mohammad Ranjbar

2013-09-01

How to cite this article: Ranjbar R, Liaghat AR, Ranjbar A, Mohabbati H. Toxicologic Laboratory Findings in Cases Reported with Hanging Death: a Two-Year Retrospective Study in Northeast Iran. Asia Pac J Med Toxicol 2013;2:92-5.

High-throughput 3D spheroid culture and drug testing using a 384 hanging drop array.

Science.gov (United States)

Tung, Yi-Chung; Hsiao, Amy Y; Allen, Steven G; Torisawa, Yu-suke; Ho, Mitchell; Takayama, Shuichi

2011-02-07

Culture of cells as three-dimensional (3D) aggregates can enhance in vitro tests for basic biological research as well as for therapeutics development. Such 3D culture models, however, are often more complicated, cumbersome, and expensive than two-dimensional (2D) cultures. This paper describes a 384-well format hanging drop culture plate that makes spheroid formation, culture, and subsequent drug testing on the obtained 3D cellular constructs as straightforward to perform and adapt to existing high-throughput screening (HTS) instruments as conventional 2D cultures. Using this platform, we show that drugs with different modes of action produce distinct responses in the physiological 3D cell spheroids compared to conventional 2D cell monolayers. Specifically, the anticancer drug 5-fluorouracil (5-FU) has higher anti-proliferative effects on 2D cultures whereas the hypoxia activated drug commonly referred to as tirapazamine (TPZ) are more effective against 3D cultures. The multiplexed 3D hanging drop culture and testing plate provides an efficient way to obtain biological insights that are often lost in 2D platforms.

Water - rock interaction in different rock environments

International Nuclear Information System (INIS)

Lamminen, S.

1995-01-01

The study assesses the groundwater geochemistry and geological environment of 44 study sites for radioactive waste disposal. Initially, the study sites were divided by rock type into 5 groups: (1) acid - intermediate rocks, (2) mafic - ultramafic rocks, (3) gabbros, amphibolites and gneisses that contain calc-silicate (skarn) rocks, (4) carbonates and (5) sandstones. Separate assessments are made of acid - intermediate plutonic rocks and of a subgroup that comprises migmatites, granite and mica gneiss. These all belong to the group of acid - intermediate rocks. Within the mafic -ultramafic rock group, a subgroup that comprises mafic - ultramafic plutonic rocks, serpentinites, mafic - ultramafic volcanic rocks and volcanic - sedimentary schists is also evaluated separately. Bedrock groundwaters are classified by their concentration of total dissolved solids as fresh, brackish, saline, strongly saline and brine-class groundwaters. (75 refs., 24 figs., 3 tabs.)

Geo-Engineering Evaluation of Rock Masses for Crushed Rock and Cut Stones in Khartoum State, Sudan

Science.gov (United States)

Kheirelseed, E. E.; Ming, T. H.; Abdalla, S. B.

The purpose of this study is to find artificial coarse aggregates and cut stones around Khartoum. To meat the objectives of the study, data from both field and laboratory are collected. The field data includes geological investigations based on different methods and samples collection, whereas the laboratory tests consists of specific gravity, water absorption, impact value, crushing value, Los Angeles abrasion, soundness tests. The field and laboratory results were weighed and compiled together to reveal the engineering performance of the different rock masses in term of cut stone and crushed aggregates. The results show that most of the examined rock masses are suitable for crushing, building and dressed stones. For decorative slabs only foliated granite and syenite masses can be used.

Oxidation of water to hydrogen peroxide at the rock-water interface due to stress-activated electric currents in rocks

NARCIS (Netherlands)

Balk, M.; Bose, M.; Ertem, G.; Rogoff, D.A.; Rothschild, L.J.; Freund, F.T.

2009-01-01

Common igneous and high-grade metamorphic rocks contain dormant defects, which release electronic charge carriers when stressed. Rocks thereby behave like a battery. The charge carriers of interest are defect electrons h¿, e.g. electronic states associated with O¿ in a matrix of O2¿. Known as

Rock cavern storage of spent fuel

Energy Technology Data Exchange (ETDEWEB)

Cho, Won Jin; Kim, Kyung Soo [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Kwon, Sang Ki [Inha University, Incheon (Korea, Republic of)

2015-12-15

The rock cavern storage for spent fuel has been assessed to apply in Korea with reviewing the state of the art of the technologies for surface storage and rock cavern storage of spent fuel. The technical feasibility and economic aspects of the rock cavern storage of spent fuel were also analyzed. A considerable area of flat land isolated from the exterior are needed to meet the requirement for the site of the surface storage facilities. It may, however, not be easy to secure such areas in the mountainous region of Korea. Instead, the spent fuel storage facilities constructed in the rock cavern moderate their demands for the suitable site. As a result, the rock cavern storage is a promising alternative for the storage of spent fuel in the aspect of natural and social environments. The rock cavern storage of spent fuel has several advantages compared with the surface storage, and there is no significant difference on the viewpoint of economy between the two alternatives. In addition, no great technical difficulties are present to apply the rock cavern storage technologies to the storage of domestic spent fuel.

Animations, games, and virtual reality for the Jing-Hang Grand Canal.

Science.gov (United States)

Chen, Wenzhi; Zhang, Mingmin; Pan, Zhigeng; Liu, Gengdai; Shen, Huaqing; Chen, Shengnan; Liu, Yong

2010-01-01

Digital heritage, an effective method to preserve and present natural and cultural heritage, is engaging many heritage preservation specialists and computer scientists. In particular, computer graphics researchers have become involved, and digital heritage has employed many CG techniques. For example, Daniel Pletinckx and his colleagues employed VR in a real museum at Ename, Belgium, and Zhigeng Pan and his colleagues applied it to construct a virtual Olympics museum. Soo-Chang Pei and his colleagues focused on restoring ancient Chinese paintings. Here, we describe how we've applied animations, computer games, and VR to China's famous Jing-Hang Grand Canal.

Ingestion of safety razor blade and delayed hanging in a complex suicide.

Science.gov (United States)

Chauhan, Mohit Singh; Behera, C; Naagar, Sunil; Sreenivas, M

2016-12-01

Ingestion of a foreign body is mostly accidental in children and intentional in prisoners to achieve hospitalization; however, use of this method of suicide is rare. We report a case where the victim first ingested a safety razor blade, but failed to die and then hanged himself, but failed again and finally succumbed to the complications on the sixth day. He had also attempted suicide by inflicting multiple incised wounds on his neck four days before the safety blade ingestion, but none were fatal. © The Author(s) 2016.

Human HepaRG Cells can be Cultured in Hanging-drop Plates for Cytochrome P450 Induction and Function Assays.

Science.gov (United States)

Murayama, Norie; Usui, Takashi; Slawny, Nicky; Chesné, Christophe; Yamazaki, Hiroshi

2015-01-01

Recent guidance/guidelines for industry recommend that cytochrome P450 induction can be assessed using human hepatocyte enzyme activity and/or mRNA levels to evaluate potential drug- drug interactions. To evaluate time-dependent cytochrome P450 induction precisely, induction of CYP1A2, CYP2B6, and CYP3A4 mRNA was confirmed (>2-fold) by the treatment with omeprazole, phenobarbital, and rifampicin, respectively, for 24 or 48 h on day 3 from the start of culture. After 24 h, the fold induction of CYP1A2 with 3.6 and 1.8x10(4) HepaRG cells per well was lower than that for 7.2x10(4) cells. CYP1A2 induction levels at 24 h were higher than those after 48 h. In contrast, higher CYP2B6 inductions were confirmed after 48 h exposure than after 24 h, independent of the number of cells per well. To help reduce the use of human cryopreserved hepatocytes, typical P450-dependent enzyme activities were investigated in human HepaRG cells cultured in commercial hanging-drop plates. Newly designed 96-well hanging-drop plates were capable of maintaining human CYP3A-dependent midazolam hydroxylation activities for up to 4 days using only 10% of the recommended initial 7.2x10(4) cells per well. Favorable HepaRG function using hanging-drop plates was confirmed by detecting 1'- hydroxymidazolam O-glucuronide on day 3, suggesting an improvement over traditional control plates in which this metabolite can be detected for 24-well plates. These results suggest that the catalytic function and/or induction of CYP1A2, CYP2B6, and CYP3A4 can be readily assessed with reduced numbers of starting HepaRG cells cultured in three-dimensional cultures in drops prepared with hanging-drop plates.

Gas migration in argillaceous rock

International Nuclear Information System (INIS)

Alonso, E. E.; Olivella, S.

2007-01-01

The intrinsic gas permeability of fractured argillaceous rocks depends on the current structure of micro-cracks and fissures of the rock. They are a consequence of the initial state and the subsequent deformations induced by stress and gas pressure changes. Stresses are also coupled with fluid pressures and, therefore, gas flow and mechanical behaviour are intensely coupled. Laboratory experiments, aimed at determining intrinsic permeability, show the relevant effect of volumetric deformations induced by isotropic, as well as deviatoric stress changes. The relevance, in practice, of the flow-mechanical coupling is illustrated by means of some results obtained during the performance of the drift scale test (DST) in fractured tuff in the Yucca Mountain facility. The technique of embedding discontinuities in continuum thermo-hydro-mechanical elements is capable of reproducing observed features of gas flow migration in clayey rocks. An example is described. It is believed that the developed approach provides a powerful computational procedure to handle complex gas phenomena in clayey rocks. (author)

How to do things with petroglyphs: the rock art of Nevada

OpenAIRE

Woody, A.J.

2000-01-01

The focus of this thesis is the rock art of Nevada, a state in the western United States. While the previously dominant models of rock art interpretation (hunting-magic and shamanism) have produced significant bodies of research, I argue that both are based on faulty Anthropological theory and produce theorisations which are one dimensional because of the focus on rock art imagery at the expense of site contexts. Because meaning is not derived from the images themselves, but is...

Thermal Inertia of Rocks and Rock Populations

Science.gov (United States)

Golombek, M. P.; Jakosky, B. M.; Mellon, M. T.

2001-01-01

The effective thermal inertia of rock populations on Mars and Earth is derived from a model of effective inertia versus rock diameter. Results allow a parameterization of the effective rock inertia versus rock abundance and bulk and fine component inertia. Additional information is contained in the original extended abstract.

Geotechnical aspects of rock borrow for large breakwaters

International Nuclear Information System (INIS)

Watson, I.; Fischer, J.A.; Urlich, C.M.

1975-01-01

The state of the art is described of investigations to secure rock borrow for the breakwaters proposed to protect offshore nuclear power plants. Considerations relating to the geological, geotechnical, and design suitability of rock are discussed within the framework of economics, and the environmental impact of quarrying and transporting rock to potential sites on the East and Gulf coasts of the U.S. is examined. The methodology outlined has application to the construction of all large rockfill breakwaters

Segmentation and rejuvenation of the Greater Himalayan sequence in western Nepal revealed by in situ U-Th/Pb monazite petrochronology

Science.gov (United States)

Braden, Zoe; Godin, Laurent; Cottle, John M.

2017-07-01

In the western Nepal Himalaya, a major mountain building shear zone, the Main Central thrust, is exposed in multiple locations along its southward transport direction. The hanging wall of the Main Central thrust was sampled in both hinterland and foreland exposures, in the upper Karnali valley and around Jumla, respectively. In situ U-Th/Pb monazite petrochronology coupled with microstructural and petrographic observations reveals distinctly different timing of deformation, despite the geographic proximity and apparent structural continuity between the two regions. The Y content, the Gd to Yb ratio and the Eu anomaly in monazite constrain the timing of metamorphic reactions. Rocks in the upper Karnali valley record deformation associated with metamorphism at 18 Ma, melt crystallization starting at ca. 14 Ma and lasting until at least 11-10 Ma. In contrast, the Jumla region records a more protracted series of events with metamorphism initiating as early as 47 Ma and lasting until 18 Ma, punctuated by at least two periods of melt crystallization. In both areas, the age of melt crystallization decreases down section through the hanging wall towards the Main Central thrust. Ductile deformation in the Jumla region ceased around ca. 18 Ma, while rocks at similar structural positions in the hinterland in upper Karnali valley were still being actively deformed and melting at ca. 11 Ma. The southern, foreland-most, hanging-wall rocks (Jumla region) were consequently exhumed above the ductile-brittle transition while the northern hinterland-most hanging-wall rocks (upper Karnali valley) were still undergoing ductile deformation and partial melting.

Generation of multicellular tumor spheroids by the hanging-drop method.

Science.gov (United States)

Timmins, Nicholas E; Nielsen, Lars K

2007-01-01

Owing to their in vivo-like characteristics, three-dimensional (3D) multicellular tumor spheroid (MCTS) cultures are gaining increasing popularity as an in vitro model of tumors. A straightforward and simple approach to the cultivation of these MCTS is the hanging-drop method. Cells are suspended in droplets of medium, where they develop into coherent 3D aggregates and are readily accessed for analysis. In addition to being simple, the method eliminates surface interactions with an underlying substratum (e.g., polystyrene plastic or agarose), requires only a low number of starting cells, and is highly reproducible. This method has also been applied to the co-cultivation of mixed cell populations, including the co-cultivation of endothelial cells and tumor cells as a model of early tumor angiogenesis.

Thermal conductivity of the rocks in the Bureau of Mines Standard Rock Suite

International Nuclear Information System (INIS)

Morgan, M.T.; West, G.A.

1980-01-01

Thermal conductivities of eight rocks from the Bureau of Mines Standard Rock Suite were measured in air over the temperature range 373 to 533 0 K (100 to 260 0 C). The thermal conductivities of these rocks were measured to furnish standards for future comparisons with host rock from prospective nuclear waste repository sites. The thermal conductivity at a given temperature decreased by as much as 9% after a specimen had been heated to the maximum temperature (533 0 K), but additional heating cycles had no further effect. This decrease was smallest in the igneous rocks and largest in the sedimentary types. Variations due to orientation were within the precision of measurements (+- 5%). In most cases the thermal conductivities were linear with the reciprocal of the temperature and were within 14% of published data obtained by other methods. Measurements were made by a cut-bar comparison method in which the sample was sandwiched between two reference or metering bars made of Pyroceram 9606 glass-ceramic. The apparatus consisted of a Dynatech Model TCFCM-N20 comparative thermal conductivity analyzer controlled by a Hewlett Packard Model 3052A data acquisition system. A program was written to increment and cycle the temperature in steps between predetermined initial and maximum values. At each step the thermal conductivity was measured after steady-state conditions were established. The rocks furnished by the Bureau of Mines were quarried in large and fairly homogeneous lots for use by researchers at various laboratories. To investigate any anisotropy, cores were taken from each rock cube perpendicular to each of the cube faces. Samples 2 in. in diameter and approx. 0.75 in. thick were prepared from the cores and were dried in a vacuum oven for at least one month prior to taking measurements

Uranium, thorium and potassium contents and radioactive equilibrium states of the uranium and thorium series nuclides in phosphate rocks and phosphate fertilizers

Energy Technology Data Exchange (ETDEWEB)

Komura, K; Yanagisawa, M; Sakurai, J; Sakanoue, M

1985-10-01

Uranium, thorium and potassium contents and radioactive equilibrium states of the uranium and thorium series nuclides have been studied for 2 phosphate rocks and 7 phosphate fertilizers. Uranium contents were found to be rather high (39-117 ppm) except for phosphate rock from Kola. The uranium series nuclides were found to be in various equilibration states, which can be grouped into following three categories. Almost in the equilibrium state, 238U approximately 230Th greater than 210Pb greater than 226Ra and 238U greater than 230Th greater than 210Pb greater than 226Ra. Thorium contents were found to be, in general, low and appreciable disequilibrium of the thorium series nuclides was not observed except one sample. Potassium contents were also very low (less than 0.3% K2O) except for complex fertilizers. Based on the present data, discussions were made for the radiation exposure due to phosphate fertilizers.

Rock pushing and sampling under rocks on Mars

Science.gov (United States)

Moore, H.J.; Liebes, S.; Crouch, D.S.; Clark, L.V.

1978-01-01

Viking Lander 2 acquired samples on Mars from beneath two rocks, where living organisms and organic molecules would be protected from ultraviolet radiation. Selection of rocks to be moved was based on scientific and engineering considerations, including rock size, rock shape, burial depth, and location in a sample field. Rock locations and topography were established using the computerized interactive video-stereophotogrammetric system and plotted on vertical profiles and in plan view. Sampler commands were developed and tested on Earth using a full-size lander and surface mock-up. The use of power by the sampler motor correlates with rock movements, which were by plowing, skidding, and rolling. Provenance of the samples was determined by measurements and interpretation of pictures and positions of the sampler arm. Analytical results demonstrate that the samples were, in fact, from beneath the rocks. Results from the Gas Chromatograph-Mass Spectrometer of the Molecular Analysis experiment and the Gas Exchange instrument of the Biology experiment indicate that more adsorbed(?) water occurs in samples under rocks than in samples exposed to the sun. This is consistent with terrestrial arid environments, where more moisture occurs in near-surface soil un- der rocks than in surrounding soil because the net heat flow is toward the soil beneath the rock and the rock cap inhibits evaporation. Inorganic analyses show that samples of soil from under the rocks have significantly less iron than soil exposed to the sun. The scientific significance of analyses of samples under the rocks is only partly evaluated, but some facts are clear. Detectable quantities of martian organic molecules were not found in the sample from under a rock by the Molecular Analysis experiment. The Biology experiments did not find definitive evidence for Earth-like living organisms in their sample. Significant amounts of adsorbed water may be present in the martian regolith. The response of the soil

Effectiveness of mesenchymal stems cells cultured by hanging drop vs. conventional culturing on the repair of hypoxic-ischemic-damaged mouse brains, measured by stemness gene expression

OpenAIRE

Lou Yongli; Guo Dewei; Zhang Hui; Song Laijun

2016-01-01

In this study, we investigated the therapeutic effects of Human Mesenchymal Stem Cells (hMSCs) cultured by hanging drop and conventional culturing methods on cerebellar repair in hypoxic-ischemic (HI) brain injured mice. Real-time quantitative reverse transcription polymerase chain reaction (RT-qPCR) was used to analyze the expression levels of three stemness genes, Oct4, Sox2 and Nanog, and the migration related gene CXCR4. MSC prepared by hanging drop or conventional techniques were adminis...

Review of potential host rocks for radioactive waste disposal in the southeast United States: Southeastern Coastal Plain Subregion

International Nuclear Information System (INIS)

1980-10-01

A literature review was made of the geological characteristics of the Southeastern Coastal Plain physiograhic province in the states of Maryland, Virginia, North Carolina, South Carolina, and Georgia. The purpose of this study was to identify candidate exploration areas for the possible location of a mined repository for the storage of radioactive waste in the argillaceous sedimentary rocks of the Coastal Plain. Candidate areas were selected on the basis of geological characteristics, available subsurface data, and generally accepted requirements for waste isolation developed by previous studies. Factors considered in the evaluation include the stratigraphy and lithology, geologic history, structure, seismicity, hydrogeology, and natural resources of the candidate area. Unlike other potential regions, the Southeastern Coastal Plain is not composed of competent rock, but consists primarily of unconsolidated and water-saturated sediments overlying a basement of crystalline and metavolcanic rocks. Thus, construction of both shafts and tunnels to depths of approx. 1000 meters may encounter difficulties. Socio-economic and construction considerations have not been addressed in the evaluation. Based on the applied criteria, four areas were selected as being most favorable for future field investigation. These include one in Maryland, one in North Carolina, and two in Georgia

Analysis of rock stress and rock stress measurements with application to Aespoe HRL

International Nuclear Information System (INIS)

Lundholm, Beatrice

2000-11-01

The process of choosing a site for a nuclear waste repository means that many aspects have to be taken into consideration. One of these is that the repository has to be mechanically stable for a long time. The mechanical stability of the rock is very difficult to determine. One of several factors, which determine the mechanical stability, is the virgin state of stress. The thesis project consists of two parts. In the first part the state of stress at Aespoe Hard Rock Laboratory had to be defined. This was done based on earlier rock stress measurements conducted during the years 1988 to 1997. Two different measurement techniques have been used, hydraulic fracturing and overcoring. During the overcoring two types of cells have been used, CSIRO HI-cell and a cell developed by the Swedish State Power Board (SSPB). In the second part of the project, investigation of the correlation between the stress and geological structures are made using numerical modelling tools such as FLAC, UDEC and 3DEC. The rock stress measurements using the hydraulic fracturing gave orientations of the horizontal stress that coincide with earlier hydraulic fracturing measurements conducted in Scandinavia. The magnitudes of rock stresses are slightly lower than the earlier reported stress magnitudes for the Scandinavian part of the earth crust. The rock stresses obtained from the overcoring resulted in higher stresses than what was predicted by the hydraulic fracturing measurements. However, the orientation of the maximum horizontal stresses coincides well between the two techniques. The orientation is also more or less constant with respect to increasing depth. The state of stress at Aespoe is defined by using the results from the hydraulic fracturing and the measurements conducted by SSPB-cell. The measurements from the SSPB-cell are used since these have a Poisson's ratio that corresponds well with the uniaxial tests of rock samples and since the measurements have been done at a distance from

Load-Unload Response Ratio (LURR), Accelerating Moment/Energy Release (AM/ER) and State Vector Saltation as Precursors to Failure of Rock Specimens

Science.gov (United States)

Yin, Xiang-Chu; Yu, Huai-Zhong; Kukshenko, Victor; Xu, Zhao-Yong; Wu, Zhishen; Li, Min; Peng, Keyin; Elizarov, Surgey; Li, Qi

2004-12-01

In order to verify some precursors such as LURR (Load/Unload Response Ratio) and AER (Accelerating Energy Release) before large earthquakes or macro-fracture in heterogeneous brittle media, four acoustic emission experiments involving large rock specimens under tri-axial stress, have been conducted. The specimens were loaded in two ways: monotonous or cycling. The experimental results confirm that LURR and AER are precursors of macro-fracture in brittle media. A new measure called the state vector has been proposed to describe the damage evolution of loaded rock specimens.

A Downflow Hanging Sponge (DHS) reactor for faecal coliform removal from an Upflow Anaerobic Sludge Bed (UASB) effluent

NARCIS (Netherlands)

Yaya Beas, R.E.; Kujawa-Roeleveld, K.; Lier, van J.B.; Zeeman, G.

2015-01-01

This research was conducted to study the faecal coliforms removal capacity of Downflow Hanging Sponge (DHS) reactors as a post-treatment for an Upflow Anaerobic Sludge Blanket (UASB) reactor. Three long-term continuous lab-scale DHS reactors i.e. a reactor with cube type sponges without

Evaporation kinetics in the hanging drop method of protein crystal growth

Science.gov (United States)

Baird, James K.; Frieden, Richard W.; Meehan, E. J., Jr.; Twigg, Pamela J.; Howard, Sandra B.; Fowlis, William A.

1987-01-01

An engineering analysis of the rate of evaporation of solvent in the hanging drop method of protein crystal growth is presented; these results are applied to 18 different drop and well arrangements commonly encountered in the laboratory, taking into account the chemical nature of the salt, the drop size and shape, the drop concentration, the well size, the well concentration, and the temperature. It is found that the rate of evaporation increases with temperature, drop size, and with the salt concentration difference between the drop and the well. The evaporation possesses no unique half-life. Once the salt in the drop achieves about 80 percent of its final concentration, further evaporation suffers from the law of diminishing returns.

75 FR 30750 - Drawbridge Operation Regulation; Arkansas Waterway, Little Rock, AR

Science.gov (United States)

2010-06-02

...-AA09 Drawbridge Operation Regulation; Arkansas Waterway, Little Rock, AR AGENCY: Coast Guard, DHS... procedures on the Baring Cross Railroad Drawbridge across the Arkansas Waterway at mile 119.6 at Little Rock....123(b) state that the draw of the Baring Cross Railroad Drawbridge, mile 119.6, at Little Rock, AR is...

The age of the rocks and the metamorphic episodes from the Southeastern of Sao Paulo state

International Nuclear Information System (INIS)

Tassinari, C.C.G.; Kawashita, K.; Schmuss, R. van; Taylor, P.N.

1988-01-01

Rb-Sr, Pb-Pb and U-Pb geochronologic studies carried out on precambrian rocks from the southeastern Sao Paulo state suggest a Complex geologic evolution during the Archean and Proterozoic times. This region is divided in five differents allochthonous terranes named Itapira-Amparo, Piracaiba-Jundiai, Sao Roque, Embu and Costeiro, separated by thrust and strike-slip faults. The Itapira-Amparo domain has a original history dating back to 3.4 Ga. and since 2.6 to 2.5 Ga. and 2.2 to 1.9 Ga. metamorphic rockformation episode occurred involving both mantle-derived magmas and recycled material. Supracrustal sequences developed around 1.4 Ga. The domain was locally reworked in 0.8 - 0.65 Ga. In the Piracaia-Jundiai the main rock-formation event occurred at 1.4 Ga., but this domian was affected by strong granization and migmatization episodes during the period 1.1 - 0.6 Ga. The third terrain is characterized by the Sao Roque metavolcanossedimentary sequence developed during the time period 1.8 - 0.7 Ga., and comprising two metamorphic superimposed events (1.4 and 0.8 - 0.7 Ga.). the post-tectonics granites ranging in ages from 0.7 to 0.55 Ga. Within the Embu terrain ages of 2.5, 1.4 and 0,75 Ga. were obtained for the metamorphic terrain, with post-tectonic activities around 650 Ma. In the Costeiro domain all the metamorphic rocks developed in late-Proterozoic time, with syntectonic phase around 650 Ma [pt

Nuclear power in rock. Principal report

International Nuclear Information System (INIS)

1977-06-01

In September 1975 the Swedish Government directed the Swedish State Power Board to study the question of rock-siting nuclear power plants. The study accounted for in this report aims at clarifying the advantages and disadvantages of siting a nuclear power plant in rock, compared to siting on ground level, considering reactor safety, war protection and sabotage. The need for nuclear power production during war situations and the closing down of nuclear power plants after terminated operation are also dealt with. (author)

Rock Directed Breaking Under the Impulse Load

Science.gov (United States)

Khomeriki, Sergo; Mataradze, Edgar; Chikhradze, Nikoloz; Losaberidze, Marine; Khomeriki, Davit; Shatberashvili, Grigol

2016-10-01

In the work the problem of directed chipping of facing stone material by means of managing of explosion process is considered. The technology of the mining of decorative stone by the use of explosion energy means the very rapid transfer of potential energy of elastic deformations to kinetic energy. As a result, the explosion impulse, in the expanse of the inertia of rock massive, does not cause the increase of existing cracks. In the course of explosion, the shock wave is propagated by ultrasonic velocity and in this case the medium parameters (pressure, density, temperature, velocity) increase in spurts. In spite of this fact the all three conservation laws of mechanics remain valid on basis of three laws the equations are derived by which the parameters of shock wave may be defined by means of the rock physical-mechanical properties. The load on the body volume at breaking under explosion acts over very small period of the time. Therefore, stressed-deformed state of the rock was studied when the impulse load acts on the boundary. It was considered that the mining of the blocks of facing stone is performed from the hard rocks. This means that the breaking proceeds in the zone of elastic deformation. In the conditions of mentioned assumptions, the expression of the stress tensor and displacement of vector components initiated by stressed-deformed state in the rock are written.

Temperature loading and rocks mechanics at final storage of radioactive waste

International Nuclear Information System (INIS)

Leijon, B.; Stephansson, O.

1979-01-01

This report describes the rock mechanical effects - in the far field - from the thermal loading at a final storage of radioactive waste in crystalline rocks. The stress distribution of a two-storey storage is described in more details. The temperature rise in a final storage of radiactive waste will create thermal stresses which may cause a failure of the rock mass, and thereby an increase of its permeability. However, the state of stress in the Earth's crust is able to neutralize the thermal stresses. By this analysis we have been able to demonstrate that the thermal stresses due to heat conduction from the final storage are compensated by the state of stress in the upper part of the crust. The absolute stress, which is the superposition of thermal stress and virgin rock stress, is in all cases found to be below the limit of failure due to frictional resistance between surfaces of constituent blocks in the rock mass. Failure by sliding friction is the most conservative failure criterion for a rock mass. (author)

Summary of rock mechanics work completed for Posiva before 2005

International Nuclear Information System (INIS)

Hudson, J.A.; Johansson, E.

2006-06-01

To plan Posiva's rock mechanics work for 2005-2006 and beyond, it was necessary to have a clear understanding of the individual components of work that had been completed for Posiva before 2005 and to assess the cumulative rock mechanics knowledge base. This review summarizes the 80 individual completed documents, which include rock mechanics reports and other reports containing rock mechanics material. They are summarised within a structured framework of rock properties, analyses and the effects of excavation. Following the introductory section, the method of structuring the rock mechanics information is presented. Then the tabulation highlighting the features of all the previous rock mechanics work is explained. This tabulation forms the Appendix; the content of each rock mechanics report that has been produced is summarized via the table headings of document number, subject area, document reference, subject matter, objectives, methodology, highlighted figures, conclusions and comments. In addition to the direct usefulness of the tabulation in summarizing each report, it has been possible to draw overall conclusions: Information has also been obtained worldwide, especially Sweden and Canada; The rock stress state has been measured but further work is required related both to in situ measurements and numerical modelling to study, e.g., the influence of deformation zones on the local stress state; The intact rock has been extensively studied: there is a good knowledge of the parameters and their values, including the anisotropic nature of the site rocks; The geometry of the fractures is included in the geological characterisation but more rock mechanics work is required on the mechanical properties; The mechanical properties of the deformation zones have not been studied in detail; The thermal properties of the site rock are relatively well understood; A new classification has been developed for constructability and long-term safety assessment. This classification

The emerald deposits of ultramafic rocks of Capoeirana and Belmont, State of Minas Gerais, Brazil

International Nuclear Information System (INIS)

Abreu Machado, G.; Schorscher, H.

1998-01-01

The emerald deposits of Capoeirana and Belmont, State of Minas Gerais (MG), Brazil, occur vithin an area comprising a deeply weathered Archean Metavulcano-Sedimentary Sequence (SVS) in tectonic contact with the Borrachudos Metagranitoids (GB) and Fluorite bearing Foliated Metagranitoids (MGF). The SVS is formed by intercalation s of ultramafic schists and amphibolites, basic to intermediate amphibolites, vulcanoclastic, metapelitic and calcsilicate schists and gneisses, banded iron formation and metacherts. The metaultramafic rocks include minor chromitite cumulates and occur at the base of the SVS. When metasomatized in the shear zones adjoining GB and MGF they host emerald mineralizations. (author)

Rocks and geology in the San Francisco Bay region

Science.gov (United States)

Stoffer, Philip W.

2002-01-01

The landscape of the San Francisco Bay region is host to a greater variety of rocks than most other regions in the United States. This introductory guide provides illustrated descriptions of 46 common and important varieties of igneous, sedimentary, and metamorphic rock found in the region. Rock types are described in context of their identification qualities, how they form, and where they occur in the region. The guide also provides discussion about of regional geology, plate tectonics, the rock cycle, the significance of the selected rock types in relation to both earth history and the impact of mineral resources on the development in the region. Maps and text also provide information where rocks, fossils, and geologic features can be visited on public lands or in association with public displays in regional museums, park visitor centers, and other public facilities.

Estimating the Wet-Rock P-Wave Velocity from the Dry-Rock P-Wave Velocity for Pyroclastic Rocks

Science.gov (United States)

Kahraman, Sair; Fener, Mustafa; Kilic, Cumhur Ozcan

2017-07-01

Seismic methods are widely used for the geotechnical investigations in volcanic areas or for the determination of the engineering properties of pyroclastic rocks in laboratory. Therefore, developing a relation between the wet- and dry-rock P-wave velocities will be helpful for engineers when evaluating the formation characteristics of pyroclastic rocks. To investigate the predictability of the wet-rock P-wave velocity from the dry-rock P-wave velocity for pyroclastic rocks P-wave velocity measurements were conducted on 27 different pyroclastic rocks. In addition, dry-rock S-wave velocity measurements were conducted. The test results were modeled using Gassmann's and Wood's theories and it was seen that estimates for saturated P-wave velocity from the theories fit well measured data. For samples having values of less and greater than 20%, practical equations were derived for reliably estimating wet-rock P-wave velocity as function of dry-rock P-wave velocity.

Stope face support systems

CSIR Research Space (South Africa)

Daehnke, A

1998-12-01

Full Text Available The primary output of this report was the determination of geotechnical areas across the gold and platinum mines to form the basis for future understanding of the rock mass behaviour around reefs where the hanging wall and footwall rock types differ...

'Escher' Rock

Science.gov (United States)

2004-01-01

[figure removed for brevity, see original site] Chemical Changes in 'Endurance' Rocks [figure removed for brevity, see original site] Figure 1 This false-color image taken by NASA's Mars Exploration Rover Opportunity shows a rock dubbed 'Escher' on the southwestern slopes of 'Endurance Crater.' Scientists believe the rock's fractures, which divide the surface into polygons, may have been formed by one of several processes. They may have been caused by the impact that created Endurance Crater, or they might have arisen when water leftover from the rock's formation dried up. A third possibility is that much later, after the rock was formed, and after the crater was created, the rock became wet once again, then dried up and developed cracks. Opportunity has spent the last 14 sols investigating Escher, specifically the target dubbed 'Kirchner,' and other similar rocks with its scientific instruments. This image was taken on sol 208 (Aug. 24, 2004) by the rover's panoramic camera, using the 750-, 530- and 430-nanometer filters. The graph above shows that rocks located deeper into 'Endurance Crater' are chemically altered to a greater degree than rocks located higher up. This chemical alteration is believed to result from exposure to water. Specifically, the graph compares ratios of chemicals between the deep rock dubbed 'Escher,' and the more shallow rock called 'Virginia,' before (red and blue lines) and after (green line) the Mars Exploration Rover Opportunity drilled into the rocks. As the red and blue lines indicate, Escher's levels of chlorine relative to Virginia's went up, and sulfur down, before the rover dug a hole into the rocks. This implies that the surface of Escher has been chemically altered to a greater extent than the surface of Virginia. Scientists are still investigating the role water played in influencing this trend. These data were taken by the rover's alpha particle X-ray spectrometer.

The state of stress in British rocks

International Nuclear Information System (INIS)

Klein, R.J.; Brown, E.T.

1983-03-01

When designing underground works, it is necessary to take account of not only the vertical stresses arising predictably from the weight of the rock overhead, but also horizontal stresses which may vary from one direction to another as a result of past tectonic action. This report discussed the techniques that have been used to measure such stresses. Few determinations have been made in Great Britain, so it has been necessary to augment what little is known by reference to fault systems, relying on correlations between the measured magnitude and direction of maximum horizontal stress with local tectonic history. This has enabled general conclusions to be reached for Great Britain. (author)

Implications of meso- to micro-scale deformation for fault sealing capacity: Insights from the Lenghu5 fold-and-thrust belt, Qaidam Basin, NE Tibetan Plateau

Science.gov (United States)

Xie, Liujuan; Pei, Yangwen; Li, Anren; Wu, Kongyou

2018-06-01

As faults can be barriers to or conduits for fluid flow, it is critical to understand fault seal processes and their effects on the sealing capacity of a fault zone. Apart from the stratigraphic juxtaposition between the hanging wall and footwall, the development of fault rocks is of great importance in changing the sealing capacity of a fault zone. Therefore, field-based structural analysis has been employed to identify the meso-scale and micro-scale deformation features and to understand their effects on modifying the porosity of fault rocks. In this study, the Lenghu5 fold-and-thrust belt (northern Qaidam Basin, NE Tibetan Plateau), with well-exposed outcrops, was selected as an example for meso-scale outcrop mapping and SEM (Scanning Electron Microscope) micro-scale structural analysis. The detailed outcrop maps enabled us to link the samples with meso-scale fault architecture. The representative rock samples, collected in both the fault zones and the undeformed hanging walls/footwalls, were studied by SEM micro-structural analysis to identify the deformation features at the micro-scale and evaluate their influences on the fluid flow properties of the fault rocks. Based on the multi-scale structural analyses, the deformation mechanisms accounting for porosity reduction in the fault rocks have been identified, which are clay smearing, phyllosilicate-framework networking and cataclasis. The sealing capacity is highly dependent on the clay content: high concentrations of clay minerals in fault rocks are likely to form continuous clay smears or micro- clay smears between framework silicates, which can significantly decrease the porosity of the fault rocks. However, there is no direct link between the fault rocks and host rocks. Similar stratigraphic juxtapositions can generate fault rocks with very different magnitudes of porosity reduction. The resultant fault rocks can only be predicted only when the fault throw is smaller than the thickness of a faulted bed, in

Langevin modelling of high-frequency Hang-Seng index data

Science.gov (United States)

Tang, Lei-Han

2003-06-01

Accurate statistical characterization of financial time series, such as compound stock indices, foreign currency exchange rates, etc., is fundamental to investment risk management, pricing of derivative products and financial decision making. Traditionally, such data were analyzed and modeled from a purely statistics point of view, with little concern on the specifics of financial markets. Increasingly, however, attention has been paid to the underlying economic forces and the collective behavior of investors. Here we summarize a novel approach to the statistical modeling of a major stock index (the Hang Seng index). Based on mathematical results previously derived in the fluid turbulence literature, we show that a Langevin equation with a variable noise amplitude correctly reproduces the ubiquitous fat tails in the probability distribution of intra-day price moves. The form of the Langevin equation suggests that, despite the extremely complex nature of financial concerns and investment strategies at the individual's level, there exist simple universal rules governing the high-frequency price move in a stock market.

Surgical results of the slipped medial rectus muscle after hang back recession surgery

Directory of Open Access Journals (Sweden)

Yasar Duranoglu

2014-12-01

Full Text Available AIM:To analyze the surgical results of a slipped medial rectus muscle (MRM after hang back recession surgery for esotropia.METHODS:Twenty-one patients who underwent re-exploration for diagnosed slipped muscle after hang back recession surgery were included in this retrospective study. Dynamic magnetic resonance imaging was performed to identify the location of the slipped muscle. Ocular motility was evaluated with assessment with prism and cover test in gaze at cardinal positions. The operations were performed by the same consultant. Intraoperative forced duction test was performed under general anesthesia. The empty sheath of the slipped MRM was resected and the muscle was advanced to the original insertion site in all patients.RESULTS:The average age of 21 patients who hadconsecutive exotropia with a slipped MRM at the time of presentation was 17.4±5.4y (5-50y. The average duration between the first operation and the diagnosis of the slipped muscle was 25mo (12 to 36mo. The mean follow up after the corrective surgery was 28mo. The mean preoperative adduction limitation in the field of action of the slipped muscle was -2.26 (ranging from -1 to -4. All patients had full adduction postoperatively.CONCLUSION:The diagnosis of the slipped muscle should be confirmed during the strabismus surgery. The slipped muscle may be caused due to insufficient suture and excessive rubbing of the eye. When divergent strabismus is observed after the recession of the MRM, a slipped muscle should be considered in the differential diagnosis.

MCCREEP - a model to estimate creep produced by microcracking around a cavity in an intact rock mass

International Nuclear Information System (INIS)

Wilkins, B.J.S.; Rigby, G.L.

1991-11-01

AECL Research is examining the disposal of nuclear fuel waste in a vault in plutonic rock. Models (MCDIRC and MCROC) have been developed to predict the mechanical behaviour of the rock in response to excavation and heat from the waste. The dominant mechanism of deformation at temperatures below 150 degrees C is microcracking, which results in rock creep and a decrease in rock strength. MCDIRC has been constructed to consider the perturbation of the stress state of intact rock by long cylindrical cavities. Slow crack-growth data are used to estimate time-dependent changes in rock strength, from which possible movements (creep strain) in the rock mass are estimated. MCDIRC depends on analytical solutions for stress-state perturbations. MCCREEP has been developed from MCDIRC and relies on the use of finite-element methods to solve for stress states. It is more flexible than MCDIRC and can deal with non-homogeneous rock properties and non-symmetrical cavities

Automatic pattern identification of rock moisture based on the Staff-RF model

Science.gov (United States)

Zheng, Wei; Tao, Kai; Jiang, Wei

2018-04-01

Studies on the moisture and damage state of rocks generally focus on the qualitative description and mechanical information of rocks. This method is not applicable to the real-time safety monitoring of rock mass. In this study, a musical staff computing model is used to quantify the acoustic emission signals of rocks with different moisture patterns. Then, the random forest (RF) method is adopted to form the staff-RF model for the real-time pattern identification of rock moisture. The entire process requires only the computing information of the AE signal and does not require the mechanical conditions of rocks.

Formulations and algorithms for problems on rock mass and support deformation during mining

Science.gov (United States)

Seryakov, VM

2018-03-01

The analysis of problem formulations to calculate stress-strain state of mine support and surrounding rocks mass in rock mechanics shows that such formulations incompletely describe the mechanical features of joint deformation in the rock mass–support system. The present paper proposes an algorithm to take into account the actual conditions of rock mass and support interaction and the algorithm implementation method to ensure efficient calculation of stresses in rocks and support.

Mechanism of rock shattering by explosions, depending on the nature of jointing and the elastic state

Energy Technology Data Exchange (ETDEWEB)

Mosinets, V N

1966-01-01

For proper use of explosives in shattering rock it is necessary to understand the mechanism of shattering. To a great extent this mechanism of shattering is controlled by fracturing in the rock and by the elastic properties of the rock. The processes of shattering as a result of explosion are analyzed, and the conclusion is made that, in its general interpretation, the mechanism of shattering is merely of theoretical interest. The applicability to actual media changes according to structure of the medium. Relatively massive rocks are characterized by an asymmetrical distribution function of the joints and micro-fractures and other inhomogeneities, the mode being shifted to the left of the asymmetry center. Rocks cut by an extensive network of microfractures and joints are characterized by an approximately normal distribution function; rocks cut by large joints have an asymmetrical distribution function, with the mode shifted to the right of the asymmetry center.

Rock fragmentation

Energy Technology Data Exchange (ETDEWEB)

Brown, W.S.; Green, S.J.; Hakala, W.W.; Hustrulid, W.A.; Maurer, W.C. (eds.)

1976-01-01

Experts in rock mechanics, mining, excavation, drilling, tunneling and use of underground space met to discuss the relative merits of a wide variety of rock fragmentation schemes. Information is presented on novel rock fracturing techniques; tunneling using electron beams, thermocorer, electric spark drills, water jets, and diamond drills; and rock fracturing research needs for mining and underground construction. (LCL)

Long term thermo-hydro-mechanical interaction behavior study of the saturated, discontinuous granitic rock mass around the radwaste repository using a steady state flow algorithm

Energy Technology Data Exchange (ETDEWEB)

Kim, Jhin Wung; Bae, Dae Suk; Kang, Chul Hyung; Choi, Jong Won [Korea Atomic Energy Research Institute, Taejeon (Korea)

2002-02-01

The objective of the present study is to understand the long term (500 years) thermo-hydro-mechanical interaction behavior of the 500 m depth underground radwaste repository in the saturated, discontinuous granitic rock mass using a steady state flow algorithm. The numerical model includes a saturated granitic rock mass with joints around the repository and a 45 .deg. C fault passing through the tunnel roof-wall intersection, and a canister with PWR spent fuels surrounded by the compacted bentonite and mixed-bentonite. Barton-Bandis joint constitutive model from the UDEC code is used for the joints. For the hydraulic analysis, a steady state flow algorithm is used for the groundwater flow through the rock joints. For the thermal analysis, heat transfer is modeled as isotropic conduction and heat decays exponentially with time. The results show that the variations of the hydraulic aperture, hydraulic conductivity, normal stress, normal displacements, and shear displacements of the joints are high in the vicinity of the repository and stay fairly constant on the region away from the repository. 14 refs., 15 figs., 11 tabs. (Author)

Rock mechanics for hard rock nuclear waste repositories

International Nuclear Information System (INIS)

Heuze, F.E.

1981-09-01

The mined geologic burial of high level nuclear waste is now the favored option for disposal. The US National Waste Terminal Storage Program designed to achieve this disposal includes an extensive rock mechanics component related to the design of the wastes repositories. The plan currently considers five candidate rock types. This paper deals with the three hard rocks among them: basalt, granite, and tuff. Their behavior is governed by geological discontinuities. Salt and shale, which exhibit behavior closer to that of a continuum, are not considered here. This paper discusses both the generic rock mechanics R and D, which are required for repository design, as well as examples of projects related to hard rock waste storage. The examples include programs in basalt (Hanford/Washington), in granitic rocks (Climax/Nevada Test Site, Idaho Springs/Colorado, Pinawa/Canada, Oracle/Arizona, and Stripa/Sweden), and in tuff

Elastic Rock Heterogeneity Controls Brittle Rock Failure during Hydraulic Fracturing

Science.gov (United States)

Langenbruch, C.; Shapiro, S. A.

2014-12-01

For interpretation and inversion of microseismic data it is important to understand, which properties of the reservoir rock control the occurrence probability of brittle rock failure and associated seismicity during hydraulic stimulation. This is especially important, when inverting for key properties like permeability and fracture conductivity. Although it became accepted that seismic events are triggered by fluid flow and the resulting perturbation of the stress field in the reservoir rock, the magnitude of stress perturbations, capable of triggering failure in rocks, can be highly variable. The controlling physical mechanism of this variability is still under discussion. We compare the occurrence of microseismic events at the Cotton Valley gas field to elastic rock heterogeneity, obtained from measurements along the treatment wells. The heterogeneity is characterized by scale invariant fluctuations of elastic properties. We observe that the elastic heterogeneity of the rock formation controls the occurrence of brittle failure. In particular, we find that the density of events is increasing with the Brittleness Index (BI) of the rock, which is defined as a combination of Young's modulus and Poisson's ratio. We evaluate the physical meaning of the BI. By applying geomechanical investigations we characterize the influence of fluctuating elastic properties in rocks on the probability of brittle rock failure. Our analysis is based on the computation of stress fluctuations caused by elastic heterogeneity of rocks. We find that elastic rock heterogeneity causes stress fluctuations of significant magnitude. Moreover, the stress changes necessary to open and reactivate fractures in rocks are strongly related to fluctuations of elastic moduli. Our analysis gives a physical explanation to the observed relation between elastic heterogeneity of the rock formation and the occurrence of brittle failure during hydraulic reservoir stimulations. A crucial factor for understanding

Rock.XML - Towards a library of rock physics models

Science.gov (United States)

Jensen, Erling Hugo; Hauge, Ragnar; Ulvmoen, Marit; Johansen, Tor Arne; Drottning, Åsmund

2016-08-01

Rock physics modelling provides tools for correlating physical properties of rocks and their constituents to the geophysical observations we measure on a larger scale. Many different theoretical and empirical models exist, to cover the range of different types of rocks. However, upon reviewing these, we see that they are all built around a few main concepts. Based on this observation, we propose a format for digitally storing the specifications for rock physics models which we have named Rock.XML. It does not only contain data about the various constituents, but also the theories and how they are used to combine these building blocks to make a representative model for a particular rock. The format is based on the Extensible Markup Language XML, making it flexible enough to handle complex models as well as scalable towards extending it with new theories and models. This technology has great advantages as far as documenting and exchanging models in an unambiguous way between people and between software. Rock.XML can become a platform for creating a library of rock physics models; making them more accessible to everyone.

Aespoe hard rock laboratory Sweden

International Nuclear Information System (INIS)

1992-01-01

The aim of the new Aespoe hard rock laboratory is to demonstrate state of the art of technology and evaluation methods before the start of actual construction work on the planned deep repository for spent nuclear fuel. The nine country OECD/NEA project in the Stripa mine in Sweden has been an excellent example of high quality international research co-operation. In Sweden the new Aespoe hard rock laboratory will gradually take over and finalize this work. SKB very much appreciates the continued international participation in Aespoe which is of great value for the quality efficiency, and confidence in this kind of work. We have invited a number of leading experts to this first international seminar to summarize the current state of a number of key questions. The contributions show the great progress that has taken place during the years. The results show that there is a solid scientific basis for using this knowledge on site specific preparation and work on actual repositories. (au)

“just hanging out with you in my back yard”: Mark Zuckerberg and Mediated Paternalism

OpenAIRE

Little Ben; Winch Alison

2018-01-01

In a video that showcases a new Facebook feature, Mark Zuckerberg chats to his users, telling them that he’s “just hanging out with you in my backyard.” In this video-which is on his Facebook page-Zuckerberg discloses the domestic space of his backyard, revealing his interaction with family and friends. Depicted hosting a barbeque while watching the electoral debate, Zuckerberg performs an affective white postfeminist paternity (Hamad, 2014) by talking about hunting, eating meat, and being a ...

REE enrichment in granite-derived regolith deposits of the southeast United States: Prospective source rocks and accumulation processes

Science.gov (United States)

Foley, Nora K.; Ayuso, Robert A.; Simandl, G.J.; Neetz, M.

2015-01-01

The Southeastern United States contains numerous anorogenic, or A-type, granites, which constitute promising source rocks for REE-enriched ion adsorption clay deposits due to their inherently high concentrations of REE. These granites have undergone a long history of chemical weathering, resulting in thick granite-derived regoliths, akin to those of South China, which supply virtually all heavy REE and Y, and a significant portion of light REE to global markets. Detailed comparisons of granite regolith profiles formed on the Stewartsville and Striped Rock plutons, and the Robertson River batholith (Virginia) indicate that REE are mobile and can attain grades comparable to those of deposits currently mined in China. A REE-enriched parent, either A-type or I-type (highly fractionated igneous type) granite, is thought to be critical for generating the high concentrations of REE in regolith profiles. One prominent feature we recognize in many granites and mineralized regoliths is the tetrad behaviour displayed in REE chondrite-normalized patterns. Tetrad patterns in granite and regolith result from processes that promote the redistribution, enrichment, and fractionation of REE, such as late- to post- magmatic alteration of granite and silicate hydrolysis in the regolith. Thus, REE patterns showing tetrad effects may be a key for discriminating highly prospective source rocks and regoliths with potential for REE ion adsorption clay deposits.

Rock burst governance of working face under igneous rock

Science.gov (United States)

Chang, Zhenxing; Yu, Yue

2017-01-01

As a typical failure phenomenon, rock burst occurs in many mines. It can not only cause the working face to cease production, but also cause serious damage to production equipment, and even result in casualties. To explore how to govern rock burst of working face under igneous rock, the 10416 working face in some mine is taken as engineering background. The supports damaged extensively and rock burst took place when the working face advanced. This paper establishes the mechanical model and conducts theoretical analysis and calculation to predict the fracture and migration mechanism and energy release of the thick hard igneous rock above the working face, and to obtain the advancing distance of the working face when the igneous rock fractures and critical value of the energy when rock burst occurs. Based on the specific conditions of the mine, this paper put forward three kinds of governance measures, which are borehole pressure relief, coal seam water injection and blasting pressure relief.

Are turtleback fault surfaces common structural elements of highly extended terranes?

Science.gov (United States)

Çemen, Ibrahim; Tekeli, Okan; Seyitoğlu, Gűrol; Isik, Veysel

2005-12-01

The Death Valley region of the U.S.A. contains three topographic surfaces resembling the carapace of a turtle. These three surfaces are well exposed along the Black Mountain front and are named the Badwater, Copper Canyon, and Mormon Point Turtlebacks. It is widely accepted that the turtlebacks are also detachment surfaces that separate brittlely deformed Cenozoic volcanic and sedimentary rocks of the hanging wall from the strongly mylonitic, ductilely deformed pre-Cenozoic rocks of the footwall. We have found a turtleback-like detachment surface along the southern margin of the Alasehir (Gediz) Graben in western Anatolia, Turkey. This surface qualifies as a turtleback fault surface because it (a) is overall convex-upward and (b) separates brittlely deformed hanging wall Cenozoic sedimentary rocks from the ductilely to brittlely deformed, strongly mylonitic pre-Cenozoic footwall rocks. The surface, named here Horzum Turtleback, contains striations that overprint mylonitic stretching lineations indicating top to the NE sense of shear. This suggests that the northeasterly directed Cenozoic extension in the region resulted in a ductile deformation at depth and as the crust isostatically adjusted to the removal of the rocks in the hanging wall of the detachment fault, the ductilely deformed mylonitic rocks of the footwall were brought to shallower depths where they were brittlely deformed. The turtleback surfaces have been considered unique to the Death Valley region, although detachment surfaces, rollover folds, and other extensional structures have been well observed in other extended terranes of the world. The presence of a turtleback fault surface in western Anatolia, Turkey, suggests that the turtleback faults may be common structural features of highly extended terranes.

Cretaceous rocks of the Western Interior basin

International Nuclear Information System (INIS)

Molenaar, C.M.; Rice, D.D.

1988-01-01

The Cretaceous rocks of the conterminous United States are discussed in this chapter. Depositional facies and lithology are reviewed along with economic resources. The economic resources include coal, hydrocarbons, and uranium

Muscle activity and spine load during anterior chain whole body linkage exercises: the body saw, hanging leg raise and walkout from a push-up.

Science.gov (United States)

McGill, Stuart; Andersen, Jordan; Cannon, Jordan

2015-01-01

This study examined anterior chain whole body linkage exercises, namely the body saw, hanging leg raise and walkout from a push-up. Investigation of these exercises focused on which particular muscles were challenged and the magnitude of the resulting spine load. Fourteen males performed the exercises while muscle activity, external force and 3D body segment motion were recorded. A sophisticated and anatomically detailed 3D model used muscle activity and body segment kinematics to estimate muscle force, and thus sensitivity to each individual's choice of motor control for each task. Gradations of muscle activity and spine load characteristics were observed across tasks. On average, the hanging straight leg raise created approximately 3000 N of spine compression while the body saw created less than 2500 N. The hanging straight leg raise created the highest challenge to the abdominal wall (>130% MVC in rectus abdominis, 88% MVC in external oblique). The body saw resulted in almost 140% MVC activation of the serratus anterior. All other exercises produced substantial abdominal challenge, although the body saw did so in the most spine conserving way. These findings, along with consideration of an individual's injury history, training goals and current fitness level, should assist in exercise choice and programme design.

For Those About to Rock : Naislaulajat rock-genressä

OpenAIRE

Herranen, Linda

2015-01-01

For those about to rock – naislaulajat rock-genressä antaa lukijalleen kokonaisvaltaisen käsityksen naisista rock-genressä: rockin historiasta, sukupuolittuneisuudesta, seksismistä, suomalaisten naislaulajien menestyksestä. Työn aineisto on koottu aihepiirin kirjallisuudesta ja alalla toimiville naislaulajille teetettyjen kyselyiden tuloksista. Lisäksi avaan omia kokemuksiani ja ajatuksiani, jotta näkökulma naisista rock-genressä tulisi esille mahdollisimman monipuolisesti. Ajatus aihees...

Proceedings of the 3. Canada-US rock mechanics symposium and 20. Canadian rock mechanics symposium : rock engineering 2009 : rock engineering in difficult conditions

Energy Technology Data Exchange (ETDEWEB)

NONE

2009-07-01

This conference provided a forum for geologists, mining operators and engineers to discuss the application of rock mechanics in engineering designs. Members of the scientific and engineering communities discussed challenges and interdisciplinary elements involved in rock engineering. New geological models and methods of characterizing rock masses and ground conditions in underground engineering projects were discussed along with excavation and mining methods. Papers presented at the conference discussed the role of rock mechanics in forensic engineering. Geophysics, geomechanics, and risk-based approaches to rock engineering designs were reviewed. Issues related to high pressure and high flow water conditions were discussed, and new rock physics models designed to enhance hydrocarbon recovery were presented. The conference featured 84 presentations, of which 9 have been catalogued separately for inclusion in this database. tabs., figs.

Rock solidification method

International Nuclear Information System (INIS)

Nakaya, Iwao; Murakami, Tadashi; Miyake, Takafumi; Funakoshi, Toshio; Inagaki, Yuzo; Hashimoto, Yasuhide.

1985-01-01

Purpose: To convert radioactive wastes into the final state for storage (artificial rocks) in a short period of time. Method: Radioactive burnable wastes such as spent papers, cloths and oils and activated carbons are burnt into ashes in a burning furnace, while radioactive liquid wastes such as liquid wastes of boric acid, exhausted cleaning water and decontaminating liquid wastes are powderized in a drying furnace or calcining furnace. These powders are joined with silicates as such as white clay, silica and glass powder and a liquid alkali such as NaOH or Ca(OH) 2 and transferred to a solidifying vessel. Then, the vessel is set to a hydrothermal reactor, heated and pressurized, then taken out about 20 min after and tightly sealed. In this way, radioactive wastes are converted through the hydrothermal reactions into aqueous rock stable for a long period of time to obtain solidification products insoluble to water and with an extremely low leaching rate. (Ikeda, J.)

Archive of information about geological samples available for research from the Ohio State University Byrd Polar and Climate Research Center (BPCRC) Polar Rock Repository

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Polar Rock Repository (PRR) operated by the Byrd Polar and Climate Research Center (BPCRC) at the Ohio State University is a partner in the Index to Marine and...

Art Rocks with Rock Art!

Science.gov (United States)

Bickett, Marianne

2011-01-01

This article discusses rock art which was the very first "art." Rock art, such as the images created on the stone surfaces of the caves of Lascaux and Altimira, is the true origin of the canvas, paintbrush, and painting media. For there, within caverns deep in the earth, the first artists mixed animal fat, urine, and saliva with powdered minerals…

A dissolution-diffusion sliding model for soft rock grains with hydro-mechanical effect

Directory of Open Access Journals (Sweden)

Z. Liu

2018-06-01

Full Text Available The deformation and failure of soft rock affected by hydro-mechanical (HM effect are one of the most concerns in geotechnical engineering, which are basically attributed to the grain sliding of soft rock. This study tried to develop a dissolution-diffusion sliding model for the typical red bed soft rock in South China. Based on hydration film, mineral dissolution and diffusion theory, and geochemical thermodynamics, a dissolution-diffusion sliding model with the HM effect was established to account for the sliding rate. Combined with the digital image processing technology, the relationship between the grain size of soft rock and the amplitude of sliding surface was presented. An equation for the strain rate of soft rocks under steady state was also derived. The reliability of the dissolution-diffusion sliding model was verified by triaxial creep tests on the soft rock with the HM coupling effect and by the relationship between the inversion average disjoining pressure and the average thickness of the hydration film. The results showed that the sliding rate of the soft rock grains was affected significantly by the waviness of sliding surface, the shear stress, and the average thickness of hydration film. The average grain size is essential for controlling the steady-state creep rate of soft rock. This study provides a new idea for investigating the deformation and failure of soft rock with the HM effect. Keywords: Soft rock, Hydro-mechanical (HM effect, Mineral dissolution-diffusion, Grain sliding model

Hydraulic Behavior in The Downflow Hanging Sponge Bioreactor

Directory of Open Access Journals (Sweden)

Izarul Machdar

2016-12-01

Full Text Available Performance efficiency in a Downflow Hanging Sponge (DHS bioreactor is associated with the amount of time that a wastewater remains in the bioreactor. The bioreactor is considered as a plug flow reactor and its hydraulic residence time (HRT depends on the void volume of packing material and the flow rate. In this study, hydraulic behavior of DHS bioreactor was investigated by using tracer method. Two types of sponge module covers, cylindrical plastic frame (module-1 and plastic hair roller (module-2, were investigated and compared. A concentrated NaCl solution used as an inert tracer and input as a pulse at the inlet of DHS bioreactor. Analysis of the residence time distribution (RTD curves provided interpretation of the index distribution or holdup water (active volume, the degree of short-circuiting, number of tanks in series (the plug flow characteristic, and the dispersion number. It was found that the actual HRT was primarily shorter than theoretical HRT of each test. Holdup water of the DHS bioreactor ranged from 60% to 97% and 36% to 60% of module-1 and module-2, respectively. Eventhough module-1 has higher effective volume than module-2, result showed that the dispersion numbers of the two modules were not significant difference. Furthermore, N-values were found larger at a higher flow rate. It was concluded that a DHS bioreactor design should incorporated a combination of water distributor system, higher loading rate at startup process to generate a hydraulic behavior closer to an ideal plug flow.ABSTRAKEfisiensi unjuk kerja bioreactor Downflow Hanging Sponge (DHS berkaitan dengan lamanya waktu tinggal limbah berada di dalam bioreaktor tersebut. Bioreaktor DHS dianggap sebagai seuatu reaktor aliran sumbat (plug flow dimana waktu tinggal hidraulik (HRT tergantung pada volume pori material isian dan laju alir. Dua jenis modul digunakan dalam penelitian ini, yang diberi nama dengan module-1 dan module-2 untuk melihat pengaruh jenis modul

Hot-dry-rock geothermal resource 1980

Energy Technology Data Exchange (ETDEWEB)

Heiken, G.; Goff, F.; Cremer, G. (ed.)

1982-04-01

The work performed on hot dry rock (HDR) geothermal resource evaluation, site characterization, and geophysical exploration techniques is summarized. The work was done by region (Far West, Pacific Northwest, Southwest, Rocky Mountain States, Midcontinent, and Eastern) and limited to the conterminous US.

Penerapan Technical Barrier to Trade melalui Pelabelan (Hang Tag Identitas Budaya pada Produk Batik

Directory of Open Access Journals (Sweden)

Siti Zulaekah

2014-12-01

Full Text Available Artikel ini bertujuan menawarkan ide/gagasan baru tentang formulasi perlindungan melalui penerapan hambatan teknis perdagangan (technical barrier to trade/TBT berupa pelabelan identitas budaya (hang tag dalam mekanisme perdagangan internasional pada produk batik.Sebagaimana diketahui, perlindungan dalam bentuk hambatan non tariff (non tariff barrier khususnya TBT yang menyangkut pelabelan produk yangberlaku selama ini sepanjang pengetahuan peneliti baru sebatas alasan keamanan pangan, kesehatan, dan lingkungan. Negara-negara yang menerap- kan hambatan dalam pelabelan di luar kategori tersebut pun masih sangat terbatas.Untuk menjawab permasalahan tersebut, penelitian ini dirancang dengan menggunakan pendekatan Hukum Normatif dengan desain penelitian kualita- tif. Penelitian menggunakan teknik participatory observation dan focus group discussion sebagai metode pengumpulan data primer. Pengumpulan data sekunder dilakukan melalui telaah kepustakaan dan inventarisasi peraturan perundang-undangan untuk data yang berupa bahan hukum. Agar data (teru- tama data primer yang diperoleh teruji keabsahannya, penelitian ini meman- faatkan metode trianggulasi yang menyatu dan tidak terpisahkan dari kegia- tan pengumpulan data primer tersebut. Analisis data menggunakan model Miles dan Huberman yang pada prinsipnya meliputi 3 (tiga tahapan yakni reduksi data, display data, dan verifikasi atau penarikan kesimpulan.Hasil penelitian menunjukkan bahwa Pemerintah Indonesia sebenarnya telah menerapkan hambatan non tarif dalam bentuk TBT pada produk batik melalui Peraturan Menteri Perindustrian tentang batikmark “batik INDONE- SIA”. Meski demikian, pelabelan tersebut masih membutuhkan rincian lagi dalam bentuk pelabelan identitas budaya sehingga maksud pelestarian batik sebagaimana diamanatkan Unesco pada Pemerintah Indonesia diharapkan menjadi terwujud.Keywords : Non Tariff Barrier, Technical Barrier to Trade,   Hang Tag, Pelabelan Identitas  Budaya

Experimental and theoretical analysis of the rate of solvent equilibration in the hanging drop method of protein crystal growth

Science.gov (United States)

Fowlis, William W.; Delucas, Lawrence J.; Twigg, Pamela J.; Howard, Sandra B.; Meehan, Edward J.

1988-01-01

The principles of the hanging-drop method of crystal growth are discussed, and the rate of water evaporation in a water droplet (containing protein, buffer, and a precipitating agent) suspended above a well containing a double concentration of precipitating agent is investigated theoretically. It is shown that, on earth, the rate of evaporation may be determined from diffusion theory and the colligative properties of solutions. The parameters affecting the rate of evaporation include the temperature, the vapor pressure of water, the ionization constant of the salt, the volume of the drop, the contact angle between the droplet and the coverslip, the number of moles of salt in the droplet, the number of moles of water and salt in the well, the molar volumes of water and salt, the distance from the droplet to the well, and the coefficient of diffusion of water vapor through air. To test the theoretical equations, hanging-drop experiments were conducted using various reagent concentrations in 25-microliter droplets and measuring the evaporation times at 4 C and 25 C. The results showed good agreement with the theory.

Headspace Hanging Drop Liquid Phase Microextraction and Gas Chromatography-Mass Spectrometry for the Analysis of Flavors from Clove Buds

Energy Technology Data Exchange (ETDEWEB)

Jung, Mi Jin; Shin, Yeon Jae; Oh, Se Yeon; Kim, Nam Sun; Kim, Kun; Lee, Dong Sun [Seoul Women' s University, Seoul (Korea, Republic of)

2006-02-15

A novel sample pretreatment technique, headspace hanging drop liquid phase microextraction (HS-LPME) was studied and applied to the determination of flavors from solid clove buds by gas chromatography-mass spectrometry (GC-MS). Several parameters affecting on HS-LPME such as organic solvent drop volume, extraction time, extraction temperature and phase ratio were investigated. 1-Octanol was selected as the extracting solvent, drop size was fixed to 0.6 μL. 60 min extraction time at 25 .deg. C was chosen. HS-LPME has the good efficiency demonstrated by the higher partition equilibrium constant (K{sub lh}) values and concentration factor (CF) values. The limits of detection (LOD) were 1.5-3.2 ng. The amounts of eugenol, β-caryophyllene and eugenol acetate from the clove bud sample were 1.90 mg/g, 1.47 mg/g and 7.0 mg/g, respectively. This hanging drop based method is a simple, fast and easy sample enrichment technique using minimal solvent. HSLPME is an alternative sample preparation method for the analysis of volatile aroma compounds by GC-MS.

Comparison of the Hang High-Pull and Loaded Jump Squat for the Development of Vertical Jump and Isometric Force-Time Characteristics.

Science.gov (United States)

Oranchuk, Dustin J; Robinson, Tracey L; Switaj, Zachary J; Drinkwater, Eric J

2017-04-15

Weightlifting movements have high skill demands and require expert coaching. Loaded jumps have a comparably lower skill demand, but may be similarly effective for improving explosive performance. The purpose of this study was to compare vertical jump performance, isometric force, and rate of force development (RFD) following a ten-week intervention employing the hang high-pull (hang-pull) or trap-bar jump squat (jump-squat). Eighteen NCAA Division II swimmers (8 males, 10 females) with at least one year of resistance training experience volunteered to participate. Testing included the squat jump (SJ), countermovement jump (CMJ) and the isometric mid-thigh pull (IMTP). Vertical ground reaction forces were analyzed to obtain jump height and relative peak power. Relative peak force, peak RFD and relative force at five time bands were obtained from the IMTP. Subjects were randomly assigned to either a hang-pull (n = 9) or jump-squat (n = 9) training group and completed a ten-week, volume-equated, periodized training program. While there was a significant main effect of training for both groups, no statistically significant between-group differences were found (p ≥ 0.17) for any of the dependent variables. However, medium effect sizes in favor of the jump-squat training group were seen in SJ height (d = 0.56) and SJ peak power (d = 0.69). Loaded jumps seem equally effective as weightlifting derivatives for improving lower-body power in experienced athletes. Since loaded jumps require less skill and less coaching expertise than weightlifting, loaded jumps should be considered where coaching complex movements is difficult.

Increased use of lethal methods and annual increase of suicide rates in Korean adolescents: comparison with adolescents in the United States.

Science.gov (United States)

Park, Subin; Cho, Soo-Churl; Kim, Bung-Nyun; Kim, Jae-Won; Yoo, Hee Jeong; Hong, Jin Pyo

2014-03-01

The lethality of the suicide method is a strong risk factor for completed suicide. We examined whether the annual change in the pattern of suicide methods was related to the annual change in suicide rates among adolescents in South Korea and the United States. We analyzed annual data for the 2000-2009 period for South Korea and the 2000-2008 period for the United States to examine time trends in the suicide rates and suicide methods of adolescents aged 10-19 years in two countries. Data on suicide methods were obtained from the World Health Organization (WHO) mortality database. Suicide rates among adolescents in the United States have remained relatively steady since 2000, whereas the suicide among Korean adolescents has increased. Between 2000 and 2009, the most common suicide method among Korean adolescents was jumping for boys and girls, whereas it was hanging for girls and firearms for boys in the United States. Along with the annual increase in suicide rates in South Korea, the incidences of jumping among males and hanging (and recently jumping) among females have increased steadily, whereas suicide by self-poisoning steadily decreased. In the United States, between 2000 and 2008, the proportion of suicides committed by hanging increased, whereas those committed using firearms steadily decreased, particularly among adolescent females. These findings suggest that the increased use of lethal suicide methods is reflected in the increase in suicide rates in Korean adolescents. The most fruitful approach to addressing the rises in jumping suicides among Korean adolescents and hanging suicides among adolescents in the United States may be through population-based initiatives to reduce the physical availability (e.g., limiting access to or fencing off tall structures) and the social acceptability (e.g., effective and responsible regulations for reporting suicide) of these methods. © 2013 The Authors. Journal of Child Psychology and Psychiatry © 2013 Association

The Usability of Rock-Like Materials for Numerical Studies on Rocks

Science.gov (United States)

Zengin, Enes; Abiddin Erguler, Zeynal

2017-04-01

The approaches of synthetic rock material and mass are widely used by many researchers for understanding the failure behavior of different rocks. In order to model the failure behavior of rock material, researchers take advantageous of different techniques and software. But, the majority of all these instruments are based on distinct element method (DEM). For modeling the failure behavior of rocks, and so to create a fundamental synthetic rock material model, it is required to perform related laboratory experiments for providing strength parameters. In modelling studies, model calibration processes are performed by using parameters of intact rocks such as porosity, grain size, modulus of elasticity and Poisson ratio. In some cases, it can be difficult or even impossible to acquire representative rock samples for laboratory experiments from heavily jointed rock masses and vuggy rocks. Considering this limitation, in this study, it was aimed to investigate the applicability of rock-like material (e.g. concrete) to understand and model the failure behavior of rock materials having complex inherent structures. For this purpose, concrete samples having a mixture of %65 cement dust and %35 water were utilized. Accordingly, intact concrete samples representing rocks were prepared in laboratory conditions and their physical properties such as porosity, pore size and density etc. were determined. In addition, to acquire the mechanical parameters of concrete samples, uniaxial compressive strength (UCS) tests were also performed by simultaneously measuring strain during testing. The measured physical and mechanical properties of these extracted concrete samples were used to create synthetic material and then uniaxial compressive tests were modeled and performed by using two dimensional discontinuum program known as Particle Flow Code (PFC2D). After modeling studies in PFC2D, approximately similar failure mechanism and testing results were achieved from both experimental and

Shear-flow coupling in non-planar rock joints

International Nuclear Information System (INIS)

Makurat, A.; Barton, N.

1985-01-01

Crystalline rock masses are regarded as a possible host rock for permanent nuclear waste disposal. During the excavation of the required shafts and tunnels, the initial state of stress will be changed and cause a deformation of the rock mass and discontinuities. During the lifetime of the nuclear repository joint apertures may change due to thermally induced stress variations during the heating and cooling phase. As the conductivity of a joint is very sensitive to its aperture, fluid flow from and towards a repository, as well as the potential transport times of radionuclides are highly dependent on the deformability of the joints. Theoretical calculations of coupled flow in rock joints (Barton et al. 1984) predict an increase of conductivity of several orders of magnitude for the first few millimeters for shear displacement. The shear-dilation-conductivity coupling for two block sizes at two effective stress levels is shown

Hanging Drop, A Best Three-Dimensional (3D) Culture Method for Primary Buffalo and Sheep Hepatocytes.

Science.gov (United States)

Shri, Meena; Agrawal, Himanshu; Rani, Payal; Singh, Dheer; Onteru, Suneel Kumar

2017-04-26

Livestock, having close resemblance to humans, could be a better source of primary hepatocytes than rodents. Herein, we successfully developed three-dimensional (3D) culturing system for primary sheep and buffalo hepatocytes. The 3D-structures of sheep hepatocytes were formed on the fifth-day and maintained until the tenth-day on polyHEMA-coated plates and in hanging drops with William's E media (HDW). Between the cultured and fresh cells, we observed a similar expression of GAPDH, HNF4α, ALB, CYP1A1, CK8 and CK18. Interestingly, a statistically significant increase was noted in the TAT, CPS, AFP, AAT, GSP and PCNA expression. In buffalo hepatocytes culture, 3D-like structures were formed on the third-day and maintained until the sixth-day on polyHEMA and HDW. The expression of HNF4α, GSP, CPS, AFP, AAT, PCNA and CK18 was similar between cultured and fresh cells. Further, a statistically significant increase in the TAT and CK8 expression, and a decrease in the GAPDH, CYP1A1 and ALB expression were noted. Among the culture systems, HDW maintained the liver transcript markers more or less similar to the fresh hepatocytes of the sheep and buffalo for ten and six days, respectively. Taken together, hanging drop is an efficient method for 3D culturing of primary sheep and buffalo hepatocytes.

Mouse ES cells have a potential to differentiate into odontoblast-like cells using hanging drop method.

Science.gov (United States)

Kawai, R; Ozeki, N; Yamaguchi, H; Tanaka, T; Nakata, K; Mogi, M; Nakamura, H

2014-05-01

We examined whether mouse embryonic stem (ES) cells can differentiate into odontoblast-like cells without epithelial-mesenchymal interaction. Cells were cultured by the 'hanging drop' method using a collagen type-I scaffold (CS) combined with bone morphogenetic protein (BMP)-4 (CS/BMP-4). Expression of odontoblast-related mRNA and protein, and cell proliferation were performed by reverse transcription-polymerase chain reaction (RT-PCR), immunofluorescence staining and WST-1 assay, respectively. Cells potently expressed odontoblast-related cell marker mRNAs following induction of odontoblastic differentiation. Dentin sialophosphoprotein, a marker of mature odontoblasts, was strongly expressed in differentiated ES cells. The cells also acquired an odontoblast-like functional phenotype, as evidenced by the appearance of alkaline phosphatase activity and calcification. The cell-surface expression of α2, α6, αV and αVβ3 integrin proteins was rapidly upregulated in differentiated cells. Finally, anti-α2 integrin antibody suppressed the expression of odontoblastic markers in cells grown using this culture system, suggesting that α2 integrin expression in ES cells triggers their differentiation into odontoblast-like cells. Mouse ES cells cultured by the 'hanging drop' method are able to differentiate into cells with odontoblast-specific physiological functions and cell-surface integrin protein expression. © 2013 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Growth factors mediated differentiation of mesenchymal stem cells to cardiac polymicrotissue using hanging drop and bioreactor.

Science.gov (United States)

Konstantinou, Dimitrios; Lei, Ming; Xia, Zhidao; Kanamarlapudi, Venkateswarlu

2015-04-01

Heart disease is the major leading cause of death worldwide and the use of stem cells promises new ways for its treatment. The relatively easy and quick acquisition of human umbilical cord matrix mesenchymal stem cells (HUMSCs) and their properties make them useful for the treatment of cardiac diseases. Therefore, the main aim of this investigation was to create cardiac polymicrotissue from HUMSCs using a combination of growth factors [sphingosine-1-phosphate (S1P) and suramin] and techniques (hanging drop and bioreactor). Using designated culture conditions of the growth factors (100 nM S1P and 500 µM suramin), cardiomyocyte differentiation medium (CDM), hanging drop, bioreactor and differentiation for 7 days, a potential specific cardiac polymicrotissue was derived from HUMSCs. The effectiveness of growth factors alone or in combination in differentiation of HUMSCs to cardiac polymicrotissue was analysed by assessing the presence of cardiac markers by immunocytochemistry. This analysis demonstrated the importance of those growth factors for the differentiation. This study for the first time demonstrated the formation of a cardiac polymicrotissue under specific culture conditions. The polymicrotissue thus obtained may be used in future as a 'patch' to cover the injured cardiac region and would thereby be useful for the treatment of heart diseases. © 2014 International Federation for Cell Biology.

Results of monitoring at Olkiluoto in 2004. Rock mechanics

International Nuclear Information System (INIS)

Riikonen, S.

2005-09-01

This report presents Posiva Oy's results of the rock mechanical monitoring programme from the year 2004. Monitoring programme was established for long time monitoring of modifications in the bedrock during the excavation of the ONKALO underground research facility stated in Olkiluoto island. This is the first annual report where rock mechanical research work has being reported also from the monitoring point of view. Rock mechanical research work consists of both GPS measurements and microseismic measurements carried out in Olkiluoto island. Both measurements have been performed during several years even before monitoring programme was established. GPS measurements have been carried out since 1995 and microseismic network has operated since 2002. There have been no significant changes in observations when studying rock mechanical results from the year 2004 and comparing them to results from the previous years. Therefore it can be said, that so far ONKALO has barely had any effect on rock mechanics in Olkiluoto. Report has been composed from the annual reports of GPS measurements.(orig.)

Voltammetric Determination of Carcinogenic Nitrobiphenyls at a Hanging Mercury Drop Electrode

Directory of Open Access Journals (Sweden)

Jiří Zima

2003-02-01

Full Text Available Differential pulse voltammetry (DPV and adsorptive stripping voltammetry (AdSV at a hanging mercury drop electrode (HMDE was used for the determination of trace amounts of carcinogenic nitrobiphenyls, namely 2-nitrobiphenyl (2-NBP, 3-nitrobiphenyl (3-NBP and 4-nitrobiphenyl (4-NBP within the concentration range from 2.10-8 to 1.10-5 mol⋅L-1 for DPV and from 2.10-9 to 1.10-7 mol⋅L-1 for AdSV using a Britton-Robinson buffer – methanol (1:1 mixture with resulting pH 12 as a base electrolyte. The practical applicability of newly developed methods was verified using model samples of drinking and river water and liquid-liquid extraction for a preliminary separation and preconcentration.

Transformation of Serpentinite to Listvenite as Recorded in the Vein History of Rocks From Oman Drilling Project Hole BT1B

Science.gov (United States)

Manning, C. E.; Kelemen, P. B.; Michibayashi, K.; Harris, M.; Urai, J. L.; de Obeso, J. C.; Jesus, A. P. M.; Zeko, D.

2017-12-01

Oman Drilling Project Hole BT1B intersected 191 m of listvenite (magnesite + quartz rock) and serpentinite in the hanging wall of the basal thrust of the Oman ophiolite. Recovery was 100%. Listvenite is the dominant lithology in the upper plate rocks (166 m). Its shows wide color and textural variation, including pseudomorphic replacement of serpentinized peridotite. Serpentinite was encountered in two main contiguous intervals totaling 25 m. In light of the strongly metasomatic nature for the origin of listvenite, a substantial portion of the core description effort was dedicated to characterization of the complex veining history recorded in the hole. Dense veining is recorded in both lithologies. The density of 200/m. The density of veins >1 mm was 50-100/m, with somewhat higher densities recorded in serpentinite than in listvenite. In order of oldest to youngest, the main vein types in serpentinite are microscopic mesh-textured serpentine veins, macroscopic serpentine veins, carbonate-oxide veins, and carbonate veins. The vein paragenesis in listvenite is: early carbonate-oxide veins, followed by carbonate and carbonate-quartz veins, then late carbonate veins. The carbonate-oxide and carbonate veins are shared by the lithologies and hold clues to the transformation of ultramafic rocks to listvenite. Carbonate-oxide veins form a distinctive set that is interpreted to be the earliest record of carbonate formation in serpentinite. They contain Fe-oxide, usually hematite, on a medial line, with antitaxial magnesite crystals growing outward and showing terminations against wall rock minerals. Antitaxial textures may be evidence of positive reaction volumes. In serpentinite, secondary serpentine after earlier serpentine is common at vein margins. Carbonate-oxide veins are the earliest observed in listvenite, where they may form isolated veins to dense, aligned networks that impart a foliated texture. In some cases, they appear to predate replacement of serpentine by

Thermo-hydro-mechanical behavior of fractured rock mass

International Nuclear Information System (INIS)

Coste, F.

1997-12-01

The purpose of this research is to model Thermo-Hydro-Mechanical behavior of fractured rock mass regarding a nuclear waste re-depository. For this, a methodology of modeling was proposed and was applied to a real underground site (EDF site at Nouvelle Romanche). This methodology consists, in a first step, to determine hydraulic and mechanical REV. Beyond the greatest of these REV, development of a finite element code allows to model all the fractures in an explicit manner. The homogenized mechanical properties are determined in drained and undrained boundary conditions by simulating triaxial tests that represent rock mass subject to loading. These simulations allow to study the evolution of hydraulic and mechanical properties as a function of stress state. Drained and undrained boundary conditions enable to discuss the validity of assimilation of a fractured rock mass to a porous medium. The simulations lead to a better understanding of the behavior of the fractured rock masses and allow to show the dominant role of the shear behavior of the fractures on the hydraulic and mechanical homogenized properties. From a thermal point of view, as long as conduction is dominant, thermal properties of the rock mass are almost the same as those the intact rock. (author)

Rock Art

Science.gov (United States)

Henn, Cynthia A.

2004-01-01

There are many interpretations for the symbols that are seen in rock art, but no decoding key has ever been discovered. This article describes one classroom's experiences with a lesson on rock art--making their rock art and developing their own personal symbols. This lesson allowed for creativity, while giving an opportunity for integration…

Imaging transport phenomena during lysozyme protein crystal growth by the hanging drop technique

Science.gov (United States)

Sethia Gupta, Anamika; Gupta, Rajive; Panigrahi, P. K.; Muralidhar, K.

2013-06-01

The present study reports the transport process that occurs during the growth of lysozyme protein crystals by the hanging drop technique. A rainbow schlieren technique has been employed for imaging changes in salt concentration. A one dimensional color filter is used to record the deflection of the light beam. An optical microscope and an X-ray crystallography unit are used to characterize the size, tetragonal shape and Bravais lattice constants of the grown crystals. A parametric study on the effect of drop composition, drop size, reservoir height and number of drops on the crystal size and quality is reported. Changes in refractive index are not large enough to create a meaningful schlieren image in the air gap between the drop and the reservoir. However, condensation of fresh water over the reservoir solution creates large changes in the concentration of NaCl, giving rise to clear color patterns in the schlieren images. These have been analyzed to obtain salt concentration profiles near the free surface of the reservoir solution as a function of time. The diffusion of fresh water into the reservoir solution at the early stages of crystal growth followed by the mass flux of salt from the bulk solution towards the free surface has been recorded. The overall crystal growth process can be classified into two regimes, as demarcated by the changes in slope of salt concentration within the reservoir. The salt concentration in the reservoir equilibrates at long times when the crystallization process is complete. Thus, transport processes in the reservoir emerge as the route to monitor protein crystal growth in the hanging drop configuration. Results show that crystal growth rate is faster for a higher lysozyme concentration, smaller drops, and larger reservoir heights.

Information base for waste repository design. Volume 3. Waste/rock interactions

International Nuclear Information System (INIS)

Koplick, C.M.; Pentz, D.L.; Oston, S.G.; Talbot, R.

1979-01-01

This report describes the important effects resulting from interaction between radioactive waste and the rock in a nuclear waste repository. The state of the art in predicting waste/rock interactions is summarized. Where possible, independent numerical calculations have been performed. Recommendations are made pointing out areas which require additional research

Cuttability Assessment of Selected Rocks Through Different Brittleness Values

Science.gov (United States)

Dursun, Arif Emre; Gokay, M. Kemal

2016-04-01

Prediction of cuttability is a critical issue for successful execution of tunnel or mining excavation projects. Rock cuttability is also used to determine specific energy, which is defined as the work done by the cutting force to excavate a unit volume of yield. Specific energy is a meaningful inverse measure of cutting efficiency, since it simply states how much energy must be expended to excavate a unit volume of rock. Brittleness is a fundamental rock property and applied in drilling and rock excavation. Brittleness is one of the most crucial rock features for rock excavation. For this reason, determination of relations between cuttability and brittleness will help rock engineers. This study aims to estimate the specific energy from different brittleness values of rocks by means of simple and multiple regression analyses. In this study, rock cutting, rock property, and brittleness index tests were carried out on 24 different rock samples with different strength values, including marble, travertine, and tuff, collected from sites around Konya Province, Turkey. Four previously used brittleness concepts were evaluated in this study, denoted as B 1 (ratio of compressive to tensile strength), B 2 (ratio of the difference between compressive and tensile strength to the sum of compressive and tensile strength), B 3 (area under the stress-strain line in relation to compressive and tensile strength), and B 9 = S 20, the percentage of fines (point load strengths of rocks using multiple regression analysis). The results suggest that the proposed simple regression-based prediction models including B 3, B 9, and B 9p outperform the other models including B 1 and B 2 and can be used for more accurate and reliable estimation of specific energy.

A deep hydrothermal fault zone in the lower oceanic crust, Samail ophiolite Oman

Science.gov (United States)

Zihlmann, B.; Mueller, S.; Koepke, J.; Teagle, D. A. H.

2017-12-01

Hydrothermal circulation is a key process for the exchange of chemical elements between the oceans and the solid Earth and for the extraction of heat from newly accreted crust at mid-ocean ridges. However, due to a dearth of samples from intact oceanic crust, or continuous samples from ophiolites, there remain major short comings in our understanding of hydrothermal circulation in the oceanic crust, especially in the deeper parts. In particular, it is unknown whether fluid recharge and discharge occurs pervasively or if it is mainly channeled within discrete zones such as faults. Here, we present a description of a hydrothermal fault zone that crops out in Wadi Gideah in the layered gabbro section of the Samail ophiolite of Oman. Field observations reveal a one meter thick chlorite-epidote normal fault with disseminated pyrite and chalcopyrite and heavily altered gabbro clasts at its core. In both, the hanging and the footwall the gabbro is altered and abundantly veined with amphibole, epidote, prehnite and zeolite. Whole rock mass balance calculations show enrichments in Fe, Mn, Sc, V, Co, Cu, Rb, Zr, Nb, Th and U and depletions of Si, Ca, Na, Cr, Zn, Sr, Ba and Pb concentrations in the fault rock compared to fresh layered gabbros. Gabbro clasts within the fault zone as well as altered rock from the hanging wall show enrichments in Na, Sc, V, Co, Rb, Zr, Nb and depletion of Cr, Ni, Cu, Zn, Sr and Pb. Strontium isotope whole rock data of the fault rock yield 87Sr/86Sr ratios of 0.7046, which is considerably more radiogenic than fresh layered gabbro from this locality (87Sr/86Sr = 0.7030 - 0.7034), and similar to black smoker hydrothermal signatures based on epidote, measured elsewhere in the ophiolite. Altered gabbro clasts within the fault zone show similar values with 87Sr/86Sr ratios of 0.7045 - 0.7050, whereas hanging wall and foot wall display values only slightly more radiogenic than fresh layered gabbro.The secondary mineral assemblages and strontium isotope

Heterogeneous arsenic enrichment in meta-sedimentary rocks in central Maine, United States

Energy Technology Data Exchange (ETDEWEB)

O' Shea, Beth, E-mail: bethoshea@sandiego.edu [Department of Marine Science and Environmental Studies, University of San Diego, 5998 Alcala Park, San Diego, CA 92110 (United States); Lamont-Doherty Earth Observatory of Columbia University, 61 Route 9W, Palisades, NY 10964 (United States); Stransky, Megan; Leitheiser, Sara [Department of Marine Science and Environmental Studies, University of San Diego, 5998 Alcala Park, San Diego, CA 92110 (United States); Brock, Patrick [School of Earth and Environmental Sciences, Queens College, City University of New York, 65-30 Kissena Blvd., Flushing, NY 11367 (United States); Marvinney, Robert G. [Maine Geological Survey, 93 State House Station, Augusta, ME 04333 (United States); Zheng, Yan [School of Earth and Environmental Sciences, Queens College, City University of New York, 65-30 Kissena Blvd., Flushing, NY 11367 (United States); Lamont-Doherty Earth Observatory of Columbia University, 61 Route 9W, Palisades, NY 10964 (United States)

2015-02-01

Arsenic is enriched up to 28 times the average crustal abundance of 4.8 mg kg{sup −1} for meta-sedimentary rocks of two adjacent formations in central Maine, USA where groundwater in the bedrock aquifer frequently contains elevated As levels. The Waterville Formation contains higher arsenic concentrations (mean As 32.9 mg kg{sup −1}, median 12.1 mg kg{sup −1}, n = 38) than the neighboring Vassalboro Group (mean As 19.1 mg kg{sup −1}, median 6.0 mg kg{sup −1}, n = 38). The Waterville Formation is a pelitic meta-sedimentary unit with abundant pyrite either visible or observed by scanning electron microprobe. Concentrations of As and S are strongly correlated (r = 0.88, p < 0.05) in the low grade phyllite rocks, and arsenic is detected up to 1944 mg kg{sup −1} in pyrite measured by electron microprobe. In contrast, statistically significant (p < 0.05) correlations between concentrations of As and S are absent in the calcareous meta-sediments of the Vassalboro Group, consistent with the absence of arsenic-rich pyrite in the protolith. Metamorphism converts the arsenic-rich pyrite to arsenic-poor pyrrhotite (mean As 1 mg kg{sup −1}, n = 15) during de-sulfidation reactions: the resulting metamorphic rocks contain arsenic but little or no sulfur indicating that the arsenic is now in new mineral hosts. Secondary weathering products such as iron oxides may host As, yet the geochemical methods employed (oxidative and reductive leaching) do not conclusively indicate that arsenic is associated only with these. Instead, silicate minerals such as biotite and garnet are present in metamorphic zones where arsenic is enriched (up to 130.8 mg kg{sup −1} As) where S is 0%. Redistribution of already variable As in the protolith during metamorphism and contemporary water–rock interaction in the aquifers, all combine to contribute to a spatially heterogeneous groundwater arsenic distribution in bedrock aquifers. - Highlights: • Arsenic is enriched up to 138 mg kg

Comparison of disposal concepts for rock salt and hard rock

International Nuclear Information System (INIS)

Papp, R.

1998-01-01

The study was carried out in the period 1994-1996. The goals were to prepare a draft on spent fuel disposal in hard rock and additionally a comparison with existing disposal concepts for rock salt. A cask for direct disposal of spent fuel and a repository for hard rock including a safeguards concept were conceptually designed. The results of the study confirm, that the early German decision to employ rock salt was reasonable. (orig.)

Relationships of stable isotopes, water-rock interaction and salinization in fractured aquifers, Petrolina region, Pernambuco State, Brazil

Energy Technology Data Exchange (ETDEWEB)

Silva, Priscila Sousa, E-mail: priscila.silva@cprm.gov.br [Serviço Geológico do Brasil (CPRM), Manaus, AM (Brazil); Campos, José Eloi Guimarães; Cunha, Luciano Soares; Mancini, Luís Henrique, E-mail: eloi@unb.br, E-mail: lucianosc@unb.br, E-mail: lmancini@unb.br [Universidade de Brasília (UnB), Brasília, DF (Brazil)

2018-01-15

The Petrolina County, Pernambuco State, Brazil, presents specificities that make it unique from a hydrogeological point of view. Water resource scarcity is both a quantitative and qualitative issue. The climate is classified as semiarid, having low precipitation, along with high temperatures and evapotranspiration rates. Aquifer zones are related to low connected fractures resulting in a restricted water flow in the aquifer. The recharge is limited and the groundwater salinity is high. Stable isotope analyses of H and O were developed in groundwater samples (with different electrical conductivity) and surface water collected in a bypass channel flowing from the São Francisco River. The results were plotted in a δD ‰ versus δ{sup 18}O ‰ graph along with the curves of the global and local meteoric water line. Groundwater samples showed unexpected results showing a lighter sign pattern when compared to the meteoric waters. More negative δD and δ{sup 18}O values indicate an enrichment in light isotopes, which show that this process is not influenced by surface processes, where the enrichment occurs in heavy isotopes due to evaporation. The isotopic signature observed is interpreted either as resulting from the water-rock interaction, or as resulting from recharge from paleo rains. The waters are old and show restricted flow. So the water-rock contact time is extended. In the rock weathering processes, through the hydration of feldspars, there is preferential assimilation of heavy isotopes at the expense of the lighter ones that remain in the water. Analyses of the {sup 87}Sr/{sup 86}Sr ratio and isotopic groundwater dating assist in the interpretations. (author)

Participation of civil engineers in designing facilities in rock salt

International Nuclear Information System (INIS)

Duddeck, H.; Westhaus, T.

1990-01-01

For the design of underground facilities in rock salt layers or domes, as caverns for repositories, the civil engineering approach may be useful. The underground openings are analysed by determining the displacements and the stresses for actual states and hypothetical situations. The paper reports on the state of art in the development of suited time dependent material laws for rock salt, on time integration methods for the analysis, and on a possible procedure for a consistent safety analysis. The examples given include caverns filled by oil, analysis of a mine with vertical excavation chambers, and dams closing mine galleries. (orig.) [de

Geohydromechanical Processes in the Excavation Damaged Zone in Crystalline Rock, Rock Salt, and Indurated and Plastic Clays

International Nuclear Information System (INIS)

Tsang, Chin-Fu; Bernier, Frederic; Davies, Christophe

2004-01-01

The creation of an excavation disturbed zone or excavation damaged zone is expected around all man-made openings in geologic formations. Macro- and micro-fracturing, and in general a redistribution of in situ stresses and rearrangement of rock structures, will occur in this zone, resulting in drastic changes of permeability to flow, mainly through the fractures and cracks induced by excavation. Such an EDZ may have significant implications for the operation and long-term performance of an underground nuclear waste repository. Various issues of concern need to be evaluated, such as processes creating fractures in the excavation damaged zone, the degree of permeability increase, and the potential for sealing or healing (with permeability reduction) in the zone. In recent years, efforts along these lines have been made for a potential repository in four rock types-crystalline rock, salt, indurated clay, and plastic clay-and these efforts have involved field, laboratory, and theoretical studies. The present work involves a synthesis of the ideas and issues that emerged from presentations and discussions on EDZ in these four rock types at a CLUSTER Conference and Workshop held in Luxembourg in November, 2003. First, definitions of excavation disturbed and excavation damaged zones are proposed. Then, an approach is suggested for the synthesis and intercomparison of geohydromechanical processes in the EDZ for the four rock types (crystalline rock, salt, indurated clay, and plastic clay). Comparison tables of relevant processes, associated factors, and modeling and testing techniques are developed. A discussion of the general state-of-the-art and outstanding issues are also presented. A substantial bibliography of relevant papers on the subject is supplied at the end of the paper

Mechanism of Rock Burst Occurrence in Specially Thick Coal Seam with Rock Parting

Science.gov (United States)

Wang, Jian-chao; Jiang, Fu-xing; Meng, Xiang-jun; Wang, Xu-you; Zhu, Si-tao; Feng, Yu

2016-05-01

Specially thick coal seam with complex construction, such as rock parting and alternative soft and hard coal, is called specially thick coal seam with rock parting (STCSRP), which easily leads to rock burst during mining. Based on the stress distribution of rock parting zone, this study investigated the mechanism, engineering discriminant conditions, prevention methods, and risk evaluation method of rock burst occurrence in STCSRP through setting up a mechanical model. The main conclusions of this study are as follows. (1) When the mining face moves closer to the rock parting zone, the original non-uniform stress of the rock parting zone and the advancing stress of the mining face are combined to intensify gradually the shearing action of coal near the mining face. When the shearing action reaches a certain degree, rock burst easily occurs near the mining face. (2) Rock burst occurrence in STCSRP is positively associated with mining depth, advancing stress concentration factor of the mining face, thickness of rock parting, bursting liability of coal, thickness ratio of rock parting to coal seam, and difference of elastic modulus between rock parting and coal, whereas negatively associated with shear strength. (3) Technologies of large-diameter drilling, coal seam water injection, and deep hole blasting can reduce advancing stress concentration factor, thickness of rock parting, and difference of elastic modulus between rock parting and coal to lower the risk of rock burst in STCSRP. (4) The research result was applied to evaluate and control the risk of rock burst occurrence in STCSRP.

Rollerjaw Rock Crusher

Science.gov (United States)

Peters, Gregory; Brown, Kyle; Fuerstenau, Stephen

2009-01-01

The rollerjaw rock crusher melds the concepts of jaw crushing and roll crushing long employed in the mining and rock-crushing industries. Rollerjaw rock crushers have been proposed for inclusion in geological exploration missions on Mars, where they would be used to pulverize rock samples into powders in the tens of micrometer particle size range required for analysis by scientific instruments.

A compilation of radioelement concentrations in granitic rocks of the contiguous United States

International Nuclear Information System (INIS)

Stuckless, J.S.; VanTrump, G. Jr.

1982-01-01

Concentration data for uranium, thorium, and potassium have been compiled for approximately 2,500 granitic samples from the contiguous United States. Uranium and thorium concentrations and ratios involving these elements exhibit a log-normal distribution with statistical parameters. In order to check for a bias in the results due to high concentrations of data in anomalous or heavily sampled areas, the data were reevaluated by averaging all analyses within a 0.5 0 latitude by 0.5 0 longitude grid. The resulting data set contains 330 entries for which radioelements are log-normally distributed. Mean values are not significantly different from those of the ungridded data, but standard deviations are lower by as much as nearly 50 percent. The areal distribution of anomalously high values (more than one standard deviation greater than the geometric mean) does not delineate large uranium districts by either treatment of the data. There is sufficient information for approximately 1,500 samples to permit subdivision of the granites by degree of alumina saturation. Relative to the six variables listed above, peraluminous samples have slightly lower mean values, but the differences are not statistically significant. Standard deviations are also largest for the peraluminous granites with α for Th/U nearly 3 times larger for peraluminous granite than for metaluminous granite. Examination of the variations in Th/U ratios for a few specific granites for which isotopic data are available suggests that variability is caused by late-stage magmatic or secondary processes that may be associated with ore-forming processes. Therefore, although anomalous radioelement concentrations in granitic rocks do not seem to be useful in delineating large uranium provinces with sediment-hosted deposits, highly variable uranium concentrations or Th/U ratios in granitic rocks may be helpful in the search for uranium deposits

Range sections as rock models for intensity rock scene segmentation

CSIR Research Space (South Africa)

Mkwelo, S

2007-11-01

Full Text Available This paper presents another approach to segmenting a scene of rocks on a conveyor belt for the purposes of measuring rock size. Rock size estimation instruments are used to monitor, optimize and control milling and crushing in the mining industry...

Determination of nitrobenzene in wastewater using a hanging mercury drop electrode.

Science.gov (United States)

Liang, Shu-Xuan; Zhang, Huan-Kun; Lu, Da

2007-06-01

The determination of trace amount nitrobenzene in wastewater on a hanging mercury drop electrode was studied. The determination conditions of pH, supporting electrolyte, accumulation potential, accumulation time, and voltammetric response were optimized. The sharp peak of the nitrobenzene was appeared at 0.05 V. The peak electric current was proportional to the concentration of nitrobenzene in the range of 1.47 x 10(-5) approximately 1.0 x 10(-3) mol/l with relative standard deviations of 3.99 approximately 8.94%. The detection limit of the nitrobenzene in water was 5 x 10(-6) mol/l. The proposed method offered low limit of determination, easy operation, the use of simple instrumentation, high sensitivity and good reproducibility. It was applied to the determination of nitrobenzene in wastewater with an average recovery of 94.0% approximately 105%. The proposed method provided fast, sensitive and sometimes real time detection of nitrobenzene.

Creep in crystalline rock with application to high level nuclear waste repository

International Nuclear Information System (INIS)

Eloranta, P.; Simonen, A.

1992-06-01

The time-dependent strength and deformation properties of hard crystalline rock are studied. Theoretical models defining the phenomena which can effect these properties are reviewed. The time- dependent deformation of the openings in the proposed nuclear waste repository is analysed. The most important factors affecting the subcritical crack growth in crystalline rock are the stress state, the chemical environment, temperature and microstructure of the rock. There are several theoretical models for the analysis of creep and cyclic fatigue: deformation diagrams, rheological models thermodynamic models, reaction rate models, stochastic models, damage models and time-dependent safety factor model. They are defective in describing the three-axial stress condition and strength criteria. In addition, the required parameters are often too difficult to determine with adequate accuracy. Therefore these models are seldom applied in practice. The effect of microcrack- driven creep on the stability of the work shaft, the emplacement tunnel and the capsulation hole of a proposed nuclear waste repository was studied using a numerical model developed by Atomic Energy of Canada Ltd. According to the model, the microcrack driven creep progresses very slowly in good quality rock. Poor rock quality may accelerate the creep rate. The model is very sensitive to the properties of the rock and secondary stress state. The results show that creep causes no stability problems on excavations in good rock. The results overestimate the effect of the creep, because the analysis omitted the effect of support structures and backfilling

Rb/Sr and K/Ar dating of Slovakia's rocks, its possibilities and interpretation

International Nuclear Information System (INIS)

Cambel, B.; Bagdasaryan, G.P.; Gukasyan, P.Kh.; Veselskij, I.

1979-01-01

Nuclear geochronological data are evaluated and summarized into histograms. On the basis of an evaluation, the results are compared obtained using various methods (K/Ar, Rb/Sr and U-Th-Pb) and the age of rocks in West Carpathians determined. It is pointed out that the age determination is dependent on the geochemical state of the studied minerals and rocks. The obtained results confirm the palaeozoic age of the majority of rocks of West Carpathians. Direct nuclear geochronological evidence of precambrium rocks has not yet been obtained. (author)

Hanging drop culture enhances differentiation of human adipose-derived stem cells into anterior neuroectodermal cells using small molecules.

Science.gov (United States)

Amirpour, Noushin; Razavi, Shahnaz; Esfandiari, Ebrahim; Hashemibeni, Batoul; Kazemi, Mohammad; Salehi, Hossein

2017-06-01

Inspired by in vivo developmental process, several studies were conducted to design a protocol for differentiating of mesenchymal stem cells into neural cells in vitro. Human adipose-derived stem cells (hADSCs) as mesenchymal stem cells are a promising source for this purpose. At current study, we applied a defined neural induction medium by using small molecules for direct differentiation of hADSCs into anterior neuroectodermal cells. Anterior neuroectodermal differentiation of hADSCs was performed by hanging drop and monolayer protocols. At these methods, three small molecules were used to suppress the BMP, Nodal, and Wnt signaling pathways in order to obtain anterior neuroectodermal (eye field) cells from hADSCs. After two and three weeks of induction, the differentiated cells with neural morphology expressed anterior neuroectodermal markers such as OTX2, SIX3, β-TUB III and PAX6. The protein expression of such markers was confirmed by real time, RT-PCR and immunocytochemistry methods According to our data, it seems that the hanging drop method is a proper approach for neuroectodermal induction of hADSCs. Considering wide availability and immunosuppressive properties of hADSCs, these cells may open a way for autologous cell therapy of neurodegenerative disorders. Copyright © 2017 ISDN. Published by Elsevier Ltd. All rights reserved.

Educational and Community Outreach Efforts by the United States Polar Rock Repository during the International Polar Year

Science.gov (United States)

Grunow, A.; Codispoti, J. E.

2010-12-01

The US Polar Rock Repository (USPRR) houses more than 19,000 rock samples from polar regions and these samples are made available to the scientific, educational and museum community. The USPRR has been active in promoting polar earth science to educational and community groups. During the past year, outreach efforts reached over 12,000 people. The USPRR outreach involve tours of the facility, school presentations, online laboratory exercises, working with the Columbus Metro Parks, teaching at summer camps, teaching special geology field assignments at the middle school level, as well as offering an ‘Antarctic Rock Box’ that contains representative samples of the three types of rocks, minerals, fossils, and books and activities about geology and Antarctica. The rock box activities have been designed and reviewed by educators and scientists to use as an educational supplement to the Earth Science course of study. The activities have been designed around the Academic Content Standards: k-12 Science manual published by the Ohio Department of Education to ensure that the activities and topics are focused on those mandated by the state of Ohio. The USPRR website has a Virtual Web Antarctic Expedition with many activities for Middle to High School age students. The students learn about how to plan a field season, safety techniques, how to make a remote field camp, identify what equipment is needed, learn about the different transportation choices, weather issues, understanding GPS, etc. Educational and community networks have been built in part, by directly contacting individuals at an institution and partnering with them on educational outreach. The institutions have been very interested in doing this because it brings scientists to the classroom and to the public. This type of outreach has also served as an opening for children to consider possible career choices in science that they may not have considered before. In many of the presentations, a female geologist

Seamless Combination of Fluorescence-Activated Cell Sorting and Hanging-Drop Networks for Individual Handling and Culturing of Stem Cells and Microtissue Spheroids.

Science.gov (United States)

Birchler, Axel; Berger, Mischa; Jäggin, Verena; Lopes, Telma; Etzrodt, Martin; Misun, Patrick Mark; Pena-Francesch, Maria; Schroeder, Timm; Hierlemann, Andreas; Frey, Olivier

2016-01-19

Open microfluidic cell culturing devices offer new possibilities to simplify loading, culturing, and harvesting of individual cells or microtissues due to the fact that liquids and cells/microtissues are directly accessible. We present a complete workflow for microfluidic handling and culturing of individual cells and microtissue spheroids, which is based on the hanging-drop network concept: The open microfluidic devices are seamlessly combined with fluorescence-activated cell sorting (FACS), so that individual cells, including stem cells, can be directly sorted into specified culturing compartments in a fully automated way and at high accuracy. Moreover, already assembled microtissue spheroids can be loaded into the microfluidic structures by using a conventional pipet. Cell and microtissue culturing is then performed in hanging drops under controlled perfusion. On-chip drop size control measures were applied to stabilize the system. Cells and microtissue spheroids can be retrieved from the chip by using a parallelized transfer method. The presented methodology holds great promise for combinatorial screening of stem-cell and multicellular-spheroid cultures.

A Hanged From the Past: Medical Consideration on the Judas Iscariot Fresco-Chapelle Notre-Dame-des-Fontaines, La Brigue (15th Century).

Science.gov (United States)

Gaeta, Raffaele; Fornaciari, Antonio

2016-09-01

The medieval chapel of Notre Dame-des-Fontaines (Our Lady of the Fountains), in the French Maritime Alps, is entirely covered by the fresco cycle of the Passion (15th century) that depicts the last days of Jesus from the Last Supper to the Resurrection. Under a small window, there is the brutal representation of the suicide of Judas Iscariot, hanging from a tree, with the abdomen quartered from which his soul, represented by a small man, is kidnapped by a devil. The author, Giovanni Canavesio, represented the traitor's death with very detailed anatomical structures, differently thus from other paintings of the same subject; it is therefore possible to assume that the artist had become familiar with the human anatomy. In particular, the realism of the hanged man's posture, neck bent in an unnatural way, allows us to hypothesize that it probably comes from direct observation of the executions of capital punishment, not infrequently imposed by the public authorities in low medieval Italy.

Rock Fracture Toughness Study Under Mixed Mode I/III Loading

Science.gov (United States)

Aliha, M. R. M.; Bahmani, A.

2017-07-01

Fracture growth in underground rock structures occurs under complex stress states, which typically include the in- and out-of-plane sliding deformation of jointed rock masses before catastrophic failure. However, the lack of a comprehensive theoretical and experimental fracture toughness study for rocks under contributions of out-of plane deformations (i.e. mode III) is one of the shortcomings of this field. Therefore, in this research the mixed mode I/III fracture toughness of a typical rock material is investigated experimentally by means of a novel cracked disc specimen subjected to bend loading. It was shown that the specimen can provide full combinations of modes I and III and consequently a complete set of mixed mode I/III fracture toughness data were determined for the tested marble rock. By moving from pure mode I towards pure mode III, fracture load was increased; however, the corresponding fracture toughness value became smaller. The obtained experimental fracture toughness results were finally predicted using theoretical and empirical fracture models.

Calculation of stresses in a rock mass and lining in stagewise face drivage

Science.gov (United States)

Seryakov, VM; Zhamalova, BR

2018-03-01

Using the method of calculating mechanical state of a rock mass for the conditions of stagewise drivage of a production face in large cross-section excavations, the specific features of stress redistribution in lining of excavations are found. The zones of tensile stresses in the lining are detected. The authors discuss the influence of the initial stress state of rocks on the tension stress zones induced in the lining in course of the heading advance

Fluid and rock interaction in permeable volcanic rock

International Nuclear Information System (INIS)

Lindley, J.I.

1985-01-01

Four types of interrelated changes -geochemical, mineralogic, isotopic, and physical - occur in Oligocene volcanic units of the Mogollon-Datil volcanic field, New Mexico. These changes resulted from the operation of a geothermal system that, through fluid-rock interaction, affected 5 rhyolite ash-flow tuffs and an intercalated basaltic andesite lava flow causing a potassium metasomatism type of alteration. (1) Previous studies have shown enrichment of rocks in K 2 O as much as 130% of their original values at the expense of Na 2 O and CaO with an accompanying increase in Rb and decreases in MgO and Sr. (2) X-ray diffraction results of this study show that phenocrystic plagioclase and groundmass feldspar have been replaced with pure potassium feldspar and quartz in altered rock. Phenocrystic potassium feldspar, biotite, and quartz are unaffected. Pyroxene in basaltic andesite is replaced by iron oxide. (3) delta 18 O increases for rhyolitic units from values of 8-10 permil, typical of unaltered rock, to 13-15 permil, typical of altered rock. Basaltic andesite, however, shows opposite behavior with a delta 18 of 9 permil in unaltered rock and 6 permit in altered. (4) Alteration results in a density decrease. SEM revealed that replacement of plagioclase by fine-grained quartz and potassium feldspar is not a volume for volume replacement. Secondary porosity is created in the volcanics by the chaotic arrangement of secondary crystals

Usage of Cable Bolts for Gateroad Maintenance in Soft Rocks

Directory of Open Access Journals (Sweden)

Iurii Khalymendyk

2014-01-01

Originality/value: 1. There are no regulations and state standards in regard to cable bolt installation parameters in the mines of Ukraine, consequently the usage of cable bolts for gateroad maintenance required preliminary testing under geological conditions at the Western Donbass mines with soft enclosing rocks. 2. Combining levelling with observations using extensometers allowed for the detection of the rock layers' uniform sagging zone in the roof of the gateroad.

Disc cutter wear and rock texture in hard rock TBM tunneling

International Nuclear Information System (INIS)

Koizumi, Yu; Tsusaka, Kimikazu; Tanimoto, Chikaosa; Nakagawa, Shigeo; Fujita, Naoya

2008-01-01

Disc cutter wear in TBM tunneling is caused by initial fragmentation of a solid rock face (the primary fragmentation) and fragmentation of residual rock pieces between a cutterhead and the face (the secondary fragmentation). In two projects through sedimentary and granitic rocks, the authors investigated the relationships between the rate of cutter wear caused by the primary fragmentation, point load index and the grain size and contents of abrasive minerals. As a result, it was found that the tensile strength and the mineral contents of rocks significantly influenced the cutter wear in both projects and thus it is necessary to take into account of rock type. (author)

Rocks Can Wow? Yes, Rocks Can Wow!

Science.gov (United States)

Hardman, Sally; Luke, Sue

2016-01-01

Rocks and fossils appear in the National Curriculum of England science programmes of study for children in year 3 (ages 7-8). A frequently asked question is "How do you make the classification of rocks engaging?" In response to this request from a school, a set of interactive activities was designed and organised by tutors and students…

Surface Hydrological Processes of Rock Glaciated Basins in the San Juan Mountains, Colorado

Science.gov (United States)

Mateo, E. I.

2017-12-01

Glaciers in the western United States have been examined in terms of their summer meltwater contributions to regional hydrological systems. In the San Juan Mountains of Colorado where glaciers do not and cannot exist due to a rising zero-degree isotherm, rock glaciers take the place of valley glaciers during the summer runoff period. Most of the rock glaciers in Colorado are located on a northerly slope aspect, however, there are multiple in the southwest region of the state that occur on different aspects. This study asked how slope aspect and rising air temperatures influenced the hydrological processes of streams below rock glaciers in the San Juan Mountains during the 2016 summer season. This project focused on three basins, Yankee Boy basin, Blue Lakes basin, and Mill Creek basin, which are adjacent to each other and share a common peak, Gilpin Peak. Findings of this one-season study showed that air temperature significantly influenced stream discharge below each rock glacier. Discharge and air temperature patterns indicate a possible air temperature threshold during late summer when rock glacier melt increased at a greater rate. The results also suggest that slope aspect of rock glacier basins influences stream discharge, but temperature and precipitation are likely larger components of the melt regimes. The continuation of data collection during the 2017 summer season has allowed for more detailed analysis of the relationship between air temperature and rock glacier melt. This continual expansion of the original dataset is crucial for understanding the hydrological processes of surface runoff below rock glaciers.

Storm Water General Permit 3 for Rock and Asphalt

Data.gov (United States)

Iowa State University GIS Support and Research Facility — General permit #3 for storm water discharges associated with industrial activity for Asphalt Plants, Concrete Batch Plants, Rock Crushing Plants and Construction...

A Novel Technique for Laparoscopic Salvage of CAPD Catheter Malfunction and Migration: The Santosh-PGI Hanging Loop Technique

Directory of Open Access Journals (Sweden)

Santosh Kumar

2015-01-01

Full Text Available CAPD catheter malfunction is a common problem. Obstruction due to wrapping by appendices epiploicae of sigmoid colon has been rarely reported in literature. We report a case of CAPD catheter malfunction caused by catheter tip migration and obstruction by appendices epiploicae that was successfully managed by laparoscopic hanging loop technique. This case report highlights the ease with which epiplopexy can be performed and catheter tip migration can be prevented by this innovative laparoscopic procedure.

Towards a comprehensive classification of igneous rocks and magmas

Science.gov (United States)

Middlemost, Eric A. K.

1991-08-01

The IUGS Subcommission on the Systematics of Igneous Rocks has recently published an excellent book on the classification of these rocks. This event has shifted the vexed question of classification towards the top of the agenda in igneous petrology. Over the years the Subcommission has used many different criteria to establish the positions of the boundaries between the various common igneous rocks. It now has to adopt a holistic approach and develop a comprehensive, coherent classification that is purged of all the minor anomalies that arise between the various classifications that it has approved. It is appreciated that the Subcommission's classification was never intended to have any genetic implications; however, it is suggested that an ideal classification should he presented in such a way that it is able to group rocks into an order that directs attention to petrogenetic relationships between individual rocks and larger groups of rocks. Unfortunately, many of the Subcommission's definitions are Earth chauvinistic; for example, igneous rocks are defined as being those rocks that solidified from a molten state either within or on the surface of the Earth. Nowhere in the book is it acknowledged that during the past 20 years, while the Subcommission has been framing its many recommendations, a whole new science of planetary petrology has subsumed classical petrology. In any new edition of the book, the Subcommission should acknowledge that rocks are essentially the solid materials of which planets, natural satellites and other broadly similar cosmic bodies are made. The Subcommission should also explicitly recognise that igneous rocks can be divided into either a main sequence of essentially common rocks or a number of supplementary clans of special rocks that evolved outside the main sequence. It is hoped that in the near future the Subcommission will rescind its recommendation that the TAS classification should be regarded as an adjunct to its more traditional

Rock Physics

DEFF Research Database (Denmark)

Fabricius, Ida Lykke

2017-01-01

Rock physics is the discipline linking petrophysical properties as derived from borehole data to surface based geophysical exploration data. It can involve interpretation of both elastic wave propagation and electrical conductivity, but in this chapter focus is on elasticity. Rock physics is based...... on continuum mechanics, and the theory of elasticity developed for statics becomes the key to petrophysical interpretation of velocity of elastic waves. In practice, rock physics involves interpretation of well logs including vertical seismic profiling (VSP) and analysis of core samples. The results...

MCDIRC: A model to estimate creep produced by microcracking around a shaft in intact rock

International Nuclear Information System (INIS)

Wilkins, B.J.S.; Rigby, G.L.

1989-12-01

Atomic Energy of Canada Limited (AECL) is studying the concept of disposing of nuclear fuel waste in a vault in plutonic rock. Models are being developed to predict the mechanical behaviour of the rock in response to excavation and heat from the waste. The dominant mechanism of deformation at temperatures below 150 degrees C is microcracking, which results in rock creep and a decrease in rock strength. A model has been constructed to consider the perturbation of the stress state of intact rock by a vertical cylindrical opening. Slow crack-growth data are used to estimate time-dependent changes in rock strength, from which the movement (creep) of the opening wall and radial strain in the rock mass can be estimated

Increased sensitivity of anodic stripping voltammetry at the hanging mercury drop electrode by ultracathodic deposition.

Science.gov (United States)

Rodrigues, José A; Rodrigues, Carlos M; Almeida, Paulo J; Valente, Inês M; Gonçalves, Luís M; Compton, Richard G; Barros, Aquiles A

2011-09-09

An improved approach to the anodic stripping voltammetric (ASV) determination of heavy metals, using the hanging mercury drop electrode (HMDE), is reported. It was discovered that using very cathodic accumulation potentials, at which the solvent reduction occurs (overpotential deposition), the voltammetric signals of zinc(II), cadmium(II), lead(II) and copper(II) increase. When compared with the classical methodology a 5 to 10-fold signal increase is obtained. This effect is likely due to both mercury drop oscillation at such cathodic potentials and added local convection at the mercury drop surface caused by the evolution of hydrogen bubbles. Copyright © 2011 Elsevier B.V. All rights reserved.

Model for determining vapor equilibrium rates in the hanging drop method for protein crystal growth

Science.gov (United States)

Baird, James K.; Frieden, Richard W.; Meehan, E. J., Jr.; Twigg, Pamela J.; Howard, Sandra B.; Fowlis, William A.

1987-01-01

An engineering analysis of the rate of evaporation of solvent in the hanging drop method of protein crystal growth is presented. Results are applied to 18 drop and well arrangements commonly encountered in the laboratory. The chemical nature of the salt, drop size and shape, drop concentration, well size, well concentration, and temperature are taken into account. The rate of evaporation increases with temperature, drop size, and the salt concentration difference between the drop and the well. The evaporation in this model possesses no unique half-life. Once the salt in the drop achieves 80 percent of its final concentration, further evaporation suffers from the law of diminishing returns.

Enrichment of cardiac differentiation of mouse embryonic stem cells by optimizing the hanging drop method.

Science.gov (United States)

Chen, Ming; Lin, Yong-Qing; Xie, Shuang-Lun; Wu, Hong-Fu; Wang, Jing-Feng

2011-04-01

Hanging drop (HD) culture is used to induce differentiation of embryonic stem cells (ESCs) into other cell types including cardiomyocytes. However, the factors affecting cardiac differentiation of ESCs with this method remain incompletely understood. We have investigated the effects of the starting number of ESCs in embryoid bodies (EBs) and the time of EB adherence to gelatin-coated plates on cardiac differentiation: cardiac differentiation was increased in the EBs by a larger number of ESCs and was decreased by plating EBs at day 4 or earlier. These two factors can thus be optimized to enrich the cardiac differentiation in ESCs using the HD method.

Relationship between the rock mass deformation and places of occurrence of seismological events

Energy Technology Data Exchange (ETDEWEB)

Janusz Makowka; Jozef Kabiesz; Lin-ming Ddou [Central Mining Institute, Katowice (Poland)

2009-09-15

Static effort of rock mass very rarely causes of rock burst in Polish coal mines. Rock bursts with source in the seismic tremor within the roof rock layers are prevailing. A seismic tremor is an effect of rupture or sliding in roof layers above the exploited panel in coal seam, sometime in a distance from actual exploitation. Sliding, as a rule occurs in fault zone and tremors in it are expected, but monolithic layer rupture is very hard to predict. In a past few years a practice of analyzing state of deformation in high energy seismic tremors zones has been employed. It let gathering experience thanks to witch determination of dangerous shape of reformatted roof is possible. In the paper some typical forms of roof rocks deformations leading to seismic tremor occurrence will be presented. In general these are various types of multidirectional rock layers bending. Real examples of seismic events and rock bursts in the Czech Republic will be shown. 5 refs., 6 figs.

Evaluation of Water Distribution and Oxygen Mass Transfer in Sponge Support Media for a Down-flow Hanging Sponge Reactor

International Nuclear Information System (INIS)

Uemura, S.; Okubo, T.; Maeno, K.; Takahashi, M.; Kubota, K.; Harada, H.

2016-01-01

A down-flow hanging sponge reactor has been developed for sewage treatment, mainly in developing countries. This novel reactor employs polyurethane sponge material as a support medium, which promises a proliferation of a large amount of biomass, offering excellent pollutant removal capability. Three types of sponge medium were evaluated with respect to water distribution and oxygen mass transfer. Water was supplied to the device, which consisted of 40 pieces of sponge media connected in series, and a tracer experiment was carried out. The ratios of actual hydraulic retention time to theoretical hydraulic retention time were in the range of 25-67% depending on the type of support medium. By supplying deoxygenated water from the top of the device, the overall volumetric oxygen transfer coefficient, K L a, was evaluated. Despite the non-aerated conditions, the K L a values of the support media were very high, in the range of 0.56-4.88 (1/min), surpassing those of other mechanically aerated processes. Furthermore, it was found that the suspended solids concentration in the influent played a role in increasing the actual hydraulic retention time/theoretical hydraulic retention time ratio, suggesting that managing the influent suspended solids concentration is prerequisite for preventing clogging problems in the down-flow hanging.

Rock History and Culture

OpenAIRE

Gonzalez, Éric

2013-01-01

Two ambitious works written by French-speaking scholars tackle rock music as a research object, from different but complementary perspectives. Both are a definite must-read for anyone interested in the contextualisation of rock music in western popular culture. In Une histoire musicale du rock (i.e. A Musical History of Rock), rock music is approached from the point of view of the people – musicians and industry – behind the music. Christophe Pirenne endeavours to examine that field from a m...

Petrophysics at the rock matrix scale: hydraulic properties and petrographic interpretation

International Nuclear Information System (INIS)

Montoto, M.

2003-01-01

The main objective of this publication is to review, summarize and make comprehensive the hydraulic properties of rocks, at the rock matrix or in tact rock scale. Also to describe how to petrographically interpret those properties. For this purpose, the procedures for the characterization and visualisation of the rock-forming components and in special the water path-ways at that scale are explained. Further more, to establish a methodological approach for an appropriate petrographic interpretation of all the mentioned properties is intended. This Technical Report is applied to the geological solution for the final disposal of high level radioactive wastes. In any case, most of the aspects covered here are of scientific and technical interest for any researcher interested in the behaviour of water in rocks and vice versa, also in the potential fluid- rock interactions. The document is divided into six Chapters, mainly theoretical and methodological, and six Appen - dixes, more focussed to practical tests and procedures for rock characterization. Two significant rock types in high level radioactive waste, HLW, granites and clays, have been used for illustrating most of the examples here included. Under a wide geological perspective, it must be stated that in any geological scenario two different systems or scales coexist; the rock massif (with fractures of about m to km) and the rock matrix (with internal discontinuities such as fissures and cracks to the order of Fm to dm). Their different behaviour is considered in Chapter 1 as well as the specific role played by the rock matrix in the long- and short-term period. General considerations about physical properties of rocks and comparative advantages and disadvantages of the main candidate rocks for radioactive repositories are also included. (Author)

Fracture Characterization in Reactive Fluid-Fractured Rock Systems Using Tracer Transport Data

Science.gov (United States)

Mukhopadhyay, S.

2014-12-01

Fractures, whether natural or engineered, exert significant controls over resource exploitation from contemporary energy sources including enhanced geothermal systems and unconventional oil and gas reserves. Consequently, fracture characterization, i.e., estimating the permeability, connectivity, and spacing of the fractures is of critical importance for determining the viability of any energy recovery program. While some progress has recently been made towards estimating these critical fracture parameters, significant uncertainties still remain. A review of tracer technology, which has a long history in fracture characterization, reveals that uncertainties exist in the estimated parameters not only because of paucity of scale-specific data but also because of knowledge gaps in the interpretation methods, particularly in interpretation of tracer data in reactive fluid-rock systems. We have recently demonstrated that the transient tracer evolution signatures in reactive fluid-rock systems are significantly different from those in non-reactive systems (Mukhopadhyay et al., 2013, 2014). For example, the tracer breakthrough curves in reactive fluid-fractured rock systems are expected to exhibit a long pseudo-state condition, during which tracer concentration does not change by any appreciable amount with passage of time. Such a pseudo-steady state condition is not observed in a non-reactive system. In this paper, we show that the presence of this pseudo-steady state condition in tracer breakthrough patterns in reactive fluid-rock systems can have important connotations for fracture characterization. We show that the time of onset of the pseudo-steady state condition and the value of tracer concentration in the pseudo-state condition can be used to reliably estimate fracture spacing and fracture-matrix interface areas.

Case histories of roller cone core bit application in crystalline rock

International Nuclear Information System (INIS)

Dahlem, J.S.

1988-01-01

The increased interest in deep crystalline rock drilling projects has resulted in a requirement for premium coring bits which are effective in such a harsh and abrasive environment. Hard formation roller cone insert bits have traditionally and constantly performed well in crystalline rock. As a result, the application of state of the art roller cone rock bit technology to the design and development of core bits has made crystalline coring projects more viable than ever before. This paper follows the development of roller cone core bits by examining their use on project such as HDR (Hot Dry Rock, Los Alamos); NAGRA (Nuclear Waste Disposal Wells in Switzerland); Camborne School of Mines Geothermal Project in Cornwall, UK; Deep Gas Project in Sweden; and the KTB Deep Drilling Project in West Germany

Geological history and its impact on the rock mechanics properties of the Olkiluoto site

International Nuclear Information System (INIS)

Hudson, J.A.; Cosgrove, J.W.

2006-03-01

This report is one of three documents with background information for supporting the development of Posiva's future rock mechanics programme. The other two reports are a summary of all the rock mechanics work completed for Posiva before 2005 (Posiva Working Report) and a technical audit of the numerical modeling work that has been conducted previously for Posiva (REC Memo). The purpose of this report is to establish the extent to which the mechanical properties of the rocks at the Olkiluoto site can be estimated from a knowledge of the geological environment. The main information required for rock mechanics studies of the site is a knowledge of the prevailing stress state, the properties of the intact rock, and the properties of the fractures at all scales - from sizes that could form blocks in the tunnel roof up to the major brittle deformation zones that could be influence the location of the ONKALO and the subsequent repository. Thus, the summary of the geological history in Chapter 2 concentrates on these features and we summarise the ductile and brittle deformational tectonic history of the site, with emphasis on the inferred stress states causing the deformations. Then, in Chapter 3, the rock stress, the hierarchy of brittle fracturing, the fracture properties and the mechanical properties of the rock mass are considered in the light of the geological environment. These features provide the baseline knowledge of the host rock from which the logic of the future rock mechanics programme can be developed, based on: the bedrock model; the site investigation results; the requirements for generating the site descriptive model; the prediction-outcome ONKALO studies; and numerically modeling the effects of excavation for design and safety analysis. The implications of this study for the future rock mechanics work are outlined in Chapter 4 with emphasis on the key features for modeling. (orig.)

Semantic modeling of plastic deformation of polycrystalline rock

Science.gov (United States)

Babaie, Hassan A.; Davarpanah, Armita

2018-02-01

We have developed the first iteration of the Plastic Rock Deformation (PRD) ontology by modeling the semantics of a selected set of deformational processes and mechanisms that produce, reconfigure, displace, and/or consume the material components of inhomogeneous polycrystalline rocks. The PRD knowledge model also classifies and formalizes the properties (relations) that hold between instances of the dynamic physical and chemical processes and the rock components, the complex physio-chemical, mathematical, and informational concepts of the plastic rock deformation system, the measured or calculated laboratory testing conditions, experimental procedures and protocols, the state and system variables, and the empirical flow laws that define the inter-relationships among the variables. The ontology reuses classes and properties from several existing ontologies that are built for physics, chemistry, biology, and mathematics. With its flexible design, the PRD ontology is well positioned to incrementally develop into a model that more fully represents the knowledge of plastic deformation of polycrystalline rocks in the future. The domain ontology will be used to consistently annotate varied data and information related to the microstructures and the physical and chemical processes that produce them at different spatial and temporal scales in the laboratory and in the solid Earth. The PRDKB knowledge base, when built based on the ontology, will help the community of experimental structural geologists and metamorphic petrologists to coherently and uniformly distribute, discover, access, share, and use their data through automated reasoning and integration and query of heterogeneous experimental deformation data that originate from autonomous rock testing laboratories.

Appraisal of hard rock for potential underground repositories of radioactive wastes

International Nuclear Information System (INIS)

Cook, N.G.W.

1977-10-01

The mechanical safety and stability of such an underground repository depends largely on the virgin state of stress in the rock, groundwater pressures, the strengths of the rocks, heating by the decay of the radioactive wastes, and the layout of the excavations and the disposition of waste cannisters within them. A large body of pertinent data exists in the literature, and each of these factors has been analyzed in the light of this information. The results indicate that there are no fundamental geological nor mechanical reasons why repositories capable of storing radioactive wastes should not be excavated at suitable sites in hard rock. However, specific tests to determine the mechanical and thermal properties of the rocks at a site would be needed to provide the data for the engineering design of a repository. Also, little experience exists of the effects on underground excavations of thermal loads, so that this aspect requires theoretical study and experimental validation. The depths of these potential repositories would lie in the range from 0.5 to 2.0 km below surface, depending upon the strength of the rock. Virgin states of stress have been measured at such depths which would retard the ingress of groundwater and obviate the incidence of faulting. A typical repository comprising three horizons each with a total area of 5 km 2 would have the capacity to store wastes with thermal output of 240 MW

The determination of nitrogen dioxide in ambient air with free hanging filters as passive samplers, and a new calibration method using fritted bubblers

NARCIS (Netherlands)

Heeres, P.; Setiawan, R.; Krol, M.C.; Adema, E.H.

2009-01-01

This paper describes two new methods for the determination of NO2 in the ambient air. The first method consists of free hanging filters with a diameter of 2.5 cm as passive samplers. The filters are impregnated with triethanolamine to bind NO2. With standard colorimetrical analysis, the amount of

Waste-rock interactions in the immediate repository

International Nuclear Information System (INIS)

McCarthy, G.J.

1977-01-01

The high level wastes (HLW's) to be placed underground in rock formations will contain significant amounts of radioactive decay heat for the first hundred-or-so years of isolation. Several physical-chemical changes analogous to natural geochemical processes can occur during this ''thermal period.'' The waste canister can act as a heat source and cause changes in the mineralogy and properties of the surrounding rocks. Geochemically, this is ''contact metamorphism.'' In the event that the canister is corroded and breached, chemical reactions can occur between the HLW, the surrounding rock and possibly the remains of the canister. In a dry repository which has not been backfilled (and thus pressurized) these interactions could be slow at best and with rates decreasing rapidly as the HLW cools. However, significant interactions can occur in years, months or even days under hydrothermal conditions. These conditions could be created by the combination of HLW heat, overburden pressure and water mobilized from the rocks or derived from groundwater intrusion. At the end of the thermal period these interaction products would constitute the actual HLW form (or ''source term'') subject to the low temperature leaching and migration processes under investigation in other laboratories. It is quite possible that these interaction product waste forms will have superior properties compared to the original HLW. Experimental programs initiated at Penn State during the last year aim at determining the nature of any chemical or mineralogical changes in, or interactions between, HLW solids and host rocks under various repository ambients. The accompanying figures describe the simulated HLW forms and the experimental approach and techniques. Studies with basalts as the repository rock are supported by Rockwell Hanford Operations and with shales by the Office of Waste Isolation

Rapid formation of rock armour for soil - rock fragment mixture during simulated rainfall

Science.gov (United States)

Poultney, E.; McGrath, G. S.; Hinz, C.

2009-04-01

Preventing erosion is an important issue in disturbed semi-arid and arid landscapes. This is in particular of highest importance for mining companies while undertaking land rehabilitation. An onsite investigation of the impact of surface rock fragments on erosion was conducted at Telfer goldmine in the Great Sandy Desert, Western Australia. The study site is a waste rock dump designed to mimic the concave slope of a natural mesa to both discourage erosion and blend in with its natural surroundings. Four treatments were used to construct the slope: two are topsoil mixed with rock fragments, and two are unmixed topsoil. A field study investigating erosion rills, particle size distribution, rock fragment coverage surface roughness and vegetation was carried out to determine changes down and across slope. The treatments constructed by mixing topsoil and rock fragments are more stable and show rock fragment distributions that more closely resemble patterns found on natural mesas surrounding Telfer. A controlled study using trays of topsoil mixed with rock fragment volumes of 50%, 60%, 70% and 80% were used to investigate how varying mixtures of rock fragments and topsoil erode using rainfall intensities between 20 and 100 mm h-1. Two runs of 25 minutes each were used to assess the temporal evolution of rock armouring. Surface coverage results converged for the 50%, 60% and 70% mixtures after the first run to coverage of about 90%, suggesting that fine sediment proportion does not affect rate and degree of rock armouring.

Closed laryngeal trauma by hanging. CT appearance, one case; Traumatisme ferme du larynx par pendaison. Aspect scanographique a propos d`un cas

Energy Technology Data Exchange (ETDEWEB)

Poquet, E.; Dibiane, A.; Jourdain, C.; El-Amine, M.; Jacob, A.; Escure, M.N. [Centre Hospitalier, 91 - Corbeil-Essonnes (France)

1995-02-01

The closed laryngeal traumas by attempt of hanging are rarely studied by medical imaging. The lesions are evaluated by fiberoptic endoscopy and CT scan. We report a case of complicated lesions of the larynx with rupture of the cricothyroid membrane, diagnosed by CT scan and we discuss the usefulness to this technique. (authors). 7 refs., 3 figs.

Development of artificial soft rock

International Nuclear Information System (INIS)

Kishi, Kiyoshi

1995-01-01

When foundation base rocks are deeper than the level of installing structures or there exist weathered rocks and crushed rocks in a part of base rocks, often sound artificial base rocks are made by substituting the part with concrete. But in the construction of Kashiwazaki Kariwa Nuclear Power Station of Tokyo Electric Power Co., Inc., the foundation base rocks consist of mudstone, and the stiffness of concrete is large as compared with the surrounding base rocks. As the quality of the substituting material, the nearly same stiffness as that of the surrounding soft rocks and long term stability are suitable, and the excellent workability and economical efficiency are required, therefore, artificial soft rocks were developed. As the substituting material, the soil mortar that can obtain the physical property values in stable form, which are similar to those of Nishiyama mudstone, was selected. The mechanism of its hardening and the long term stability, and the manufacturing plant are reported. As for its application to the base rocks of Kashiwazaki Kariwa Nuclear Power Station, the verification test at the site and the application to the base rocks for No. 7 plant reactor building and other places are described. (K.I.)

Development of a New Hanging-Type Esophageal Stent for Preventing Migration: A Preliminary Study in an Animal Model of Esophagotracheal Fistula

Energy Technology Data Exchange (ETDEWEB)

Endo, Masayuki, E-mail: masay010@yahoo.co.jp; Kaminou, Toshio, E-mail: kaminout@med.tottori-u.ac.jp; Ohuchi, Yasufumi, E-mail: oyasu@med.tottori-u.ac.jp [Tottori University, Department of Radiology, Faculty of Medicine (Japan); Sugiura, Kimihiko, E-mail: kimihikosugiura@gmail.com [Yonago Medical Center, Department of Radiology (Japan); Yata, Shinsaku, E-mail: yata-s@med.tottori-u.ac.jp; Adachi, Akira, E-mail: july1st@med.tottori-u.ac.jp; Kawai, Tsuyoshi, E-mail: prgr-xxio@kuc.biglobe.ne.jp; Takasugi, Syohei, E-mail: stakasugi@med.tottori-u.ac.jp; Yamamoto, Shuichi, E-mail: yamamotoshu@med.tottori-u.ac.jp; Matsumoto, Kensuke, E-mail: matsumoto-k@v103.vaio.ne.jp [Tottori University, Department of Radiology, Faculty of Medicine (Japan); Hashimoto, Masayuki, E-mail: hashimotom@pref.tottori.jp [Tottori Prefectural Kosei Hospital, Department of Radiology (Japan); Ihaya, Takashi, E-mail: iahaya@orange.ocn.ne.jp [Sanin Rosai Hospital, Department of Radiology (Japan); Ogawa, Toshihide, E-mail: ogawa@med.tottori-u.ac.jp [Tottori University, Department of Radiology, Faculty of Medicine (Japan)

2012-10-15

Purpose: Covered, self-expandable metallic stents (SEMS) have been enthusiastically adopted for the treatment of esophagotracheal fistula, but problems with stent migration have yet to be resolved. To overcome this problem, we have developed a new hanging-type esophageal stent designed to prevent migration, and we conducted an animal study to assess the efficacy of our method. Methods: A total of six female pigs were used in this study. The main characteristic of our stent was the presence of a string tied to the proximal edge of the stent for fixation under the skin of the neck. The first experiment was performed to confirm technical feasibility in three pigs with esophagotracheal fistula. The second experiment was performed to evaluate stent migration and esophagotracheal fistula in three pigs. Results: Creation of the esophagotracheal fistula and stent placement were technically successful in all pigs. In the first experiment, esophagotracheal fistula was sealed by stent placement. In the second experiment, no stent migration was seen 11 or 12 days after stent placement. Gross findings showed no fistulas on the esophageal or tracheal wall. Conclusions: Our new hanging-type esophageal stent seems to offer a feasible method for preventing stent migration.

Development of a New Hanging-Type Esophageal Stent for Preventing Migration: A Preliminary Study in an Animal Model of Esophagotracheal Fistula

International Nuclear Information System (INIS)

Endo, Masayuki; Kaminou, Toshio; Ohuchi, Yasufumi; Sugiura, Kimihiko; Yata, Shinsaku; Adachi, Akira; Kawai, Tsuyoshi; Takasugi, Syohei; Yamamoto, Shuichi; Matsumoto, Kensuke; Hashimoto, Masayuki; Ihaya, Takashi; Ogawa, Toshihide

2012-01-01

Purpose: Covered, self-expandable metallic stents (SEMS) have been enthusiastically adopted for the treatment of esophagotracheal fistula, but problems with stent migration have yet to be resolved. To overcome this problem, we have developed a new hanging-type esophageal stent designed to prevent migration, and we conducted an animal study to assess the efficacy of our method. Methods: A total of six female pigs were used in this study. The main characteristic of our stent was the presence of a string tied to the proximal edge of the stent for fixation under the skin of the neck. The first experiment was performed to confirm technical feasibility in three pigs with esophagotracheal fistula. The second experiment was performed to evaluate stent migration and esophagotracheal fistula in three pigs. Results: Creation of the esophagotracheal fistula and stent placement were technically successful in all pigs. In the first experiment, esophagotracheal fistula was sealed by stent placement. In the second experiment, no stent migration was seen 11 or 12 days after stent placement. Gross findings showed no fistulas on the esophageal or tracheal wall. Conclusions: Our new hanging-type esophageal stent seems to offer a feasible method for preventing stent migration.

Optimal formation of genetically modified and functional pancreatic islet spheroids by using hanging-drop strategy.

Science.gov (United States)

Kim, H J; Alam, Z; Hwang, J W; Hwang, Y H; Kim, M J; Yoon, S; Byun, Y; Lee, D Y

2013-03-01

Rejection and hypoxia are important factors causing islet loss at an early stage after pancreatic islet transplantation. Recently, islets have been dissociated into single cells for reaggregation into so-called islet spheroids. Herein, we used a hanging-drop strategy to form islet spheroids to achieve functional equivalence to intact islets. To obtain single islet cells, we dissociated islets with trypsin-EDTA digestion for 10 minutes. To obtain spheroids, we dropped various numbers of single cells (125, 250, or 500 cells/30 μL drop) onto a Petri dish, that was inverted for incubation in humidified air containing 5% CO(2) at 37 °C for 7 days. The aggregated spheroids in the droplets were harvested for further culture. The size of the aggregated islet spheroids depended on the number of single cells (125-500 cells/30 μL droplet). Their morphology was similar to that of intact islets without any cellular damage. When treated with various concentrations of glucose to evaluate responsiveness, their glucose-mediated stimulation index value was similar to that of intact islets, an observation that was attributed to strong cell-to-cell interactions in islet spheroids. However, islet spheroids aggregated in general culture dishes showed abnormal glucose responsiveness owing to weak cell-to-cell interactions. Cell-to-cell interactions in islet spheroids were confirmed with an anti-connexin-36 monoclonal antibody. Finally, nonviral poly(ethylene imine)-mediated interleukin-10 cytokine gene delivered beforehand into dissociated single cells before formation of islet spheroids increased the gene transfection efficacy and interleukin-10 secretion from islet spheroids >4-fold compared with intact islets. These results demonstrated the potential application of genetically modified, functional islet spheroids with of controlled size and morphology using an hanging-drop technique. Copyright © 2013 Elsevier Inc. All rights reserved.

Industrial tests of rock consolidation for fighting floor swelling

Energy Technology Data Exchange (ETDEWEB)

Pirskii, A A; Stovpnik, S N [KPI (USSR)

1990-04-01

Reports on investigations into the mechanism of floor swelling in main roadways and into rock mass stabilization by consolidating fluid injection combined with blasting. The principal cause of deterioration in the stability of workings is considered to be the state of stress in the rock mass, rock destruction in side walls where rock blocks are being pressed into the floor while the floor rock is squeezed out into the working space. A case study of fluid injection combined with blasting applied in several mines in the Donbass is presented where holes were drilled 1.5-3 m deep and explosive charges of 0.07-0.1 kg/hole and injection of hardening solutions (0.56-0.83 m{sup 3}/m of workings) were applied. As a result floor swelling rates were reduced by up to about 5 times (e.g. from 2.5 mm/d to 0.5 mm/d.). The period of maintenence free upkeep of workings was extended to 6-8 years. The economic effect in maintenance of 1 m of workings was 11.7 rubles for floor consolidation without sidewall bolting and 51.4 rubles for floor consolidation combined with sidewall bolting. Recommendations that concern the technology of floor consolidation by fluid injection and blasting are made. 4 refs.

Steady-state flow in a rock mass intersected by permeable fracture zones

International Nuclear Information System (INIS)

Lindbom, B.

1986-12-01

Level 1 of HYDROCOIN consists of seven well-defined test problems. This paper is concerned with Case 2, which is formulated as a generic groundwater flow situation often found in crystalline rock with highly permeable fracture zones in a less permeable rock mass. The case is two-dimensional and modelled with 8-noded, isoparametric, rectangular elements. According to the case definition, calculations of hydraulic head and particle tracking are performed. The computations are carried out with varying degree of discretisation in order to analyse possible impact on the result with respect to nodal density. Further calculations have been performed mainly devoted to mass balance deviations and how these are affected by permeability contrasts, varying degree of spatial discretisation and distortion of finite elements. The distribution of hydraulic head in the domain is less sensitive to differences in nodal density than the trajectories. The hydraulic heads show similar behaviour for three meshes with varying degrees of discretisation. The particle tracking seems to be more sensitive to the level of discretisation. The results obtained with a coarse and medium mesh indicate completely different solutions for one of the pathlines. The coarse mesh is too sparsely discretised for the specified problem. The local mass balance is evaluated for seven runs. The mass balance deviation seems to be considerably more sensitive to the level of discretisation than to both permeability contrasts and deformation of elements. The permeability contrasts between the rock mass and fracture zones vary from a factor of 1000 to 1 (homogeneous properties) with increments of a factor of 10. These calculations in fact give better mass balance with increasing permeability contrasts, contrary to what could be expected. (orig./HP)

Voltammetric analysis of N-containing drugs using the hanging galinstan drop electrode (HGDE).

Science.gov (United States)

Channaa, H; Surmann, P

2009-03-01

The electrochemical behaviour of several N-containing voltammetric active drugs such as 1,4-benzodiazepines (chlordiazepoxide, nitrazepam and diazepam) as well as one nitro-compound (nitrofurantoin) and one azo-compound (phenazopyridine) is described using a new kind of liquid electrode, the hanging galinstan drop electrode. Concentrations of 10(-5) - 10(-8) mol L(-1) are generally measurable. Differential pulse and adsorptive stripping voltammograms are recorded in different supporting electrolytes, like 0.1 M KNO3, acetate buffer solution pH = 4.6 and phosphate buffer solution pH = 7.0. The effects of varying the starting potentials, U(start) for DPV and accumulation times, t(acc) for AdSV are considered. Briefly, it is shown that the novel galinstan electrode is suitable for reducing several functional groups in organic substances, here presented for N-oxide-, azomethine-, nitro- and azo-groups.

Teaching the Rock Cycle with Ease.

Science.gov (United States)

Bereki, Debra

2000-01-01

Describes a hands-on lesson for teaching high school students the concept of the rock cycle using sedimentary, metamorphic, and igneous rocks. Students use a rock cycle diagram to identify pairs of rocks. From the rock cycle, students explain on paper how their first rock became the second rock and vice versa. (PVD)

Recreating Rocks

DEFF Research Database (Denmark)

Posth, Nicole R

2008-01-01

Nicole Posth and colleagues spent a month touring South African rock formations in their quest to understand the origin of ancient iron and silicate layers.......Nicole Posth and colleagues spent a month touring South African rock formations in their quest to understand the origin of ancient iron and silicate layers....

Hydrological characteristics of Japanese rock

International Nuclear Information System (INIS)

Ijiri, Yuji; Sawada, Atsushi; Akahori, Kuniaki

1999-11-01

It is crucial to evaluate the hydrogeological characteristics of rock in Japan in order to assess the performance of geosphere. This report summarizes the hydrogeological characteristics of various rock types obtained from broad literature surveys and the fields experiments at the Kamaishi mine in northern Japan and at the Tono mine in central Japan. It is found that the hydraulic conductivity of rock mass ranges from 10 -9 m/s to 10 -8 m/s, whereas the hydraulic conductivity of fault zone ranges from 10 -9 m/s to 10 -3 m/s. It is also found that the hydraulic conductivity tends to decrease with depth. Therefore, the hydraulic conductivity of rock mass at the depth of a repository will be smaller than above values. From the investigations at outcrops and galleries throughout the country, fractures are observed as potential pathways in all rock types. All kinds of crystalline rocks and pre-Neogene sedimentary rocks are classified as fractured media where fracture flow is dominant. Among these rocks, granitic rock is considered the archetype fractured media. On the other hand, andesite, tuff and Neogene sedimentary rocks are considered as intermediate between fractured media and porous media where flow in fractures as well as in rock matrix are significant. (author)

Some new developments in the design rules for coastal structures in relation with the new Rock Manual

NARCIS (Netherlands)

Verhagen, H.J.

2005-01-01

In 1991 CUR in the Netherlands and CIRIA in the UK have published the "manual on the use of rock in coastal engineering", usually referred to as the "Rock Manual". This book of 600 pages gave an overview of the state of the art regarding the design of rock structures along coasts. In 1995 CUR

Clay shale as host rock. A geomechanical contribution about Opalinus clay

International Nuclear Information System (INIS)

Lempp, Christof; Menezes, Flora; Sachwitz, Simon

2016-01-01

The Opalinuston is a prominent rock representing the type of organic clay shales or clay stones within the sequence of Triassic and Jurassic marine sediments in Southern Germany. The rock forms a homogenous unit some ten meters thick. The degree of consolidation of this type of pelitic rock depends mainly on the former load conditions, but is also dependent on the long-term weathering and even on the present exposition. The geomechanical parameters such as shear strength, tensional strength and permeability vary with the state of consolidation and become important when the use is discussed of such rocks for radioactive waste disposal. A tunneling project at the northern escarpment of the Swabian Alb (Southwest Germany) within the Opalinus clay offered the rare opportunity to obtain fresh unweathered rock samples in greater amounts compared to fresh drilling cores from which geomechanical investigations are usually undertaken. Consequently, the results of geomechanical laboratory testings are presented in order to compare here the results of multistep triaxial compression tests, of hydraulic fracturing laboratory tests and of some other tests for rock characterization with the corresponding results of Opalinus clay sites in Switzerland that were investigated by the Swiss Nagra Company for host rock characterization. After a discussion of the relevant state of fresh Opalinus clay, especially of suction pressure conditions and saturation state, the results of triaxial shear tests are presented. Increasing shear deformation at increasing pressure and unchanged water saturation do not result in a significant strength reduction of the Opalinus clay. The rock shows increasing cohesion and stiffness, if multiple loading has repeatedly reached the failure point. Thus there is no increased permeability with continued shearing. Only at the beginning of the shearing process is a temporarily increased permeability to be expected due to dilatation processes. An increased

Rock Goes to School on Screen: A Model for Teaching Non-"Learned" Musics Derived from the Films "School of Rock" (2003) and "Rock School" (2005)

Science.gov (United States)

Webb, Michael

2007-01-01

What can be learned from two films with "rock" and "school" in their titles, about rock in school and about music and schooling more broadly? "School of Rock" (2003), a "family comedy," and "Rock School" (2005), a documentary, provoke a range of questions, ideological and otherwise, surrounding the inclusion of rock in formal instructional…

Grinding into Soft, Powdery Rock

Science.gov (United States)

2004-01-01

This hole in a rock dubbed 'Clovis' is the deepest hole drilled so far in any rock on Mars. NASA's Mars Exploration Rover Spirit captured this view with its microscopic imager on martian sol 217 (Aug. 12, 2004) after drilling 8.9 millimeters (0.35 inch) into the rock with its rock abrasion tool. The view is a mosaic of four frames taken by the microscopic imager. The hole is 4.5 centimeters (1.8 inches) in diameter. Clovis is key to a developing story about environmental change on Mars, not only because it is among the softest rocks encountered so far in Gusev Crater, but also because it contains mineral alterations that extend relatively deep beneath its surface. In fact, as evidenced by its fairly crumbly texture, it is possibly the most highly altered volcanic rock ever studied on Mars. Scientific analysis shows that the rock contains higher levels of the elements sulfur, chlorine, and bromine than are normally encountered in basaltic rocks, such as a rock dubbed 'Humphrey' that Spirit encountered two months after arriving on Mars. Humphrey showed elevated levels of sulfur, chlorine, and bromine only in the outermost 2 millimeters (less than 0.1 inch) of its surface. Clovis shows elevated levels of the same elements along with the associated softness of the rock within a borehole that is 4 times as deep. Scientists hope to compare Clovis to other, less-altered rocks in the vicinity to assess what sort of water-based processes altered the rock. Hypotheses include transport of sulfur, chlorine, and bromine in water vapor in volcanic gases; hydrothermal circulation (flow of volcanically heated water through rock); or saturation in a briny soup containing the same elements. In this image, very fine-grained material from the rock has clumped together by electrostatic attraction and fallen into the borehole. NASA/JPL/Cornell/USGS

Searching for new features of intravitality of hanging based on macro- and microscopic evaluation of the proximal attachment of the sternocleidomastoid muscle and the mastoid process of the temporal bone.

Science.gov (United States)

Szleszkowski, Ł; Hałoń, A; Thannhäuser, A; Jurek, T

2015-01-01

Assessment of the usefulness of intravital lesions in the proximal attachment of the sternocleidomastoid muscle and the mastoid process of the temporal bone in medico-legal evaluation of death by hanging. The study material was obtained from the bodies of 35 people who died by hanging. The control group comprised specimens collected from 30 people who died of non-traumatic causes. The structures under study were examined macro- and microscopically. The basic change which could be recognized as a marker of intravitality of hanging was the presence of a macroscopically extensive blotchy area of abundant ecchymosis in the proximal muscle attachment, similar to that found in the distal attachment, and the presence of abundant diffuse intraosseous ecchymoses in the mastoid process. None of the cases revealed any ecchymoses in the proximal attachment of the muscle that would be similar to those present in the distal attachment. Discolourations within the mastoid processes, macroscopically suggestive of extensive intraosseous effusions arising from the mechanism of stretching, were not confirmed by microscopic evaluation and occurred at the same frequency as in the control group. Limitations of the study were related to the method which involved sample collection by means of bone chisels, decalcification and preparation of specimens, which had an effect, for example, on the measurable evaluation of the degree of congestion. The study has failed to provide convincing and unambiguous data on the usefulness of examining mastoid processes and proximal attachments of the sternocleidomastoid muscles during autopsy to determine the presence of intravitality features of hanging. A description of research methodology and its associated difficulties, e.g. with the interpretation of results, can also be useful for the planning of similar studies by other researchers.

Searching for new features of intravitality of hanging based on macro- and microscopic evaluation of the proximal attachment of the sternocleidomastoid muscle and the mastoid process of the temporal bone

Directory of Open Access Journals (Sweden)

Łukasz Szleszkowski

2016-03-01

Full Text Available Aim of the study : Assessment of the usefulness of intravital lesions in the proximal attachment of the sternocleidomastoid muscle and the mastoid process of the temporal bone in medico-legal evaluation of death by hanging. Material and methods: The study material was obtained from the bodies of 35 people who died by hanging. The control group comprised specimens collected from 30 people who died of non-traumatic causes. The structures under study were examined macro- and microscopically. The basic change which could be recognized as a marker of intravitality of hanging was the presence of a macroscopically extensive blotchy area of abundant ecchymosis in the proximal muscle attachment, similar to that found in the distal attachment, and the presence of abundant diffuse intraosseous ecchymoses in the mastoid process. Results: None of the cases revealed any ecchymoses in the proximal attachment of the muscle that would be similar to those present in the distal attachment. Discolourations within the mastoid processes, macroscopically suggestive of extensive intraosseous effusions arising from the mechanism of stretching, were not confirmed by microscopic evaluation and occurred at the same frequency as in the control group. Limitations of the study were related to the method which involved sample collection by means of bone chisels, decalcification and preparation of specimens, which had an effect, for example, on the measurable evaluation of the degree of congestion. Conclusions : The study has failed to provide convincing and unambiguous data on the usefulness of examining mastoid processes and proximal attachments of the sternocleidomastoid muscles during autopsy to determine the presence of intravitality features of hanging. A description of research methodology and its associated difficulties, e.g. with the interpretation of results, can also be useful for the planning of similar studies by other researchers.

Kinetic approach for interactive reactions of radionuclide, bacteria and granitic crushed rock

International Nuclear Information System (INIS)

Kim, Jung Woo; Baik, Min Hoon; Lee, Seung Yeop; Lee, Jae Kwang; Kim, Seung Soo; Oh, Jong Min; Lee, Tae Yup

2011-01-01

For many radionuclides, sorption is an important phenomenon as their migration rates in groundwater are reduced in both engineered barrier and fractured rock matrix. Sorption of radionuclides is strongly dependent on the chemistry of the surrounding groundwater, such as pH, Eh, ionic strength, etc., by changing their valence states (e.g.,). In addition, it is also known that some bacteria can change the mobility and speciation of a radionuclide in groundwater. Biological immobilization mechanisms of radionuclides include precipitation, transformation to less soluble forms and so on. On the other hand, bacteria can also play a role of sorbent for radionuclides. Since bacteria can not only be mobile as a colloid but also be immobile as biofilm in the rock fracture, the bacteria as the sorbents of radionuclides in the groundwater can have both positive and negative effects on the radionuclide migration. In this study, therefore, sorption of radionuclide onto rock surface in the presence of bacteria was investigated via batch experiments. Although sorption equilibrium state can be expected in the transport of weakly sorbing (distribution coefficient, K d -3 m 3 kg -1 ) or strongly adsorbing (K d > ∼4.6 m 3 kg -1 ) nuclides in fractured rock, sorption kinetics needs to be considered in the intermediate range. Therefore, the sorption of radionuclide whose valence state is expected to be changed by biological reduction was evaluated in a kinetic approach

THM-coupled modeling of selected processes in argillaceous rock relevant to rock mechanics

International Nuclear Information System (INIS)

Czaikowski, Oliver

2012-01-01

Scientific investigations in European countries other than Germany concentrate not only on granite formations (Switzerland, Sweden) but also on argillaceous rock formations (France, Switzerland, Belgium) to assess their suitability as host and barrier rock for the final storage of radioactive waste. In Germany, rock salt has been under thorough study as a host rock over the past few decades. According to a study by the German Federal Institute for Geosciences and Natural Resources, however, not only salt deposits but also argillaceous rock deposits are available at relevant depths and of extensions in space which make final storage of high-level radioactive waste basically possible in Germany. Equally qualified findings about the suitability/unsuitability of non-saline rock formations require fundamental studies to be conducted nationally because of the comparatively low level of knowledge. The article presents basic analyses of coupled mechanical and hydraulic properties of argillaceous rock formations as host rock for a repository. The interaction of various processes is explained on the basis of knowledge derived from laboratory studies, and open problems are deduced. For modeling coupled processes, a simplified analytical computation method is proposed and compared with the results of numerical simulations, and the limits to its application are outlined. (orig.)

The appilcation of variogram to the evaluation of vocanic uranium mineralization in Gan-Hang structural belt

International Nuclear Information System (INIS)

Li Hanbo; Pan Wei; Mao Yuxian

2010-01-01

Based on a brief introduction of principle, algorithm of variogram and the geological condition of study area, variogram was introduced into the correlation study of volcanic type uranium mineralization and terrain. The process of calculating variogram of terrain elevation where uranium deposits (orefield) with different scales occur in Gan-Hang Tectonic Belt was described in detail. The geological significance of variogram statistics was preliminarily analyzed. The results show that the long axis direction of variogram of terrain elevation could reflect the main structure direction of study area, while the radius of long axis and short axis of variogram are consistent with uranium mineralization scales in a certain extent. (authors)

Experimental validation of tip over stability of a tracked mobile manipulator

CSIR Research Space (South Africa)

Dube, C

2013-09-01

Full Text Available hanging wall (roof has to be inspected for loose rock that could potentially fall and cause injuries. This inspection is typically performed by a miner who is in constant danger while performing the task. The aim of the MSP project is to remove the miner... form danger by sending in a robot to perform the post-blast inspection. The platform will explore and create a map of the mine stope and it’s manipulator will then perform inspections of the hanging wall. An iRobot PackBot510 robot is currently being...

Nonlinear Analysis of Cavities in Rock Salt

DEFF Research Database (Denmark)

Ottosen, N. S.; Krenk, Steen

1979-01-01

The paper covers some material and computational aspects of the rock mechanics of leached cavities in salt. A material model is presented in which the instantaneous stiffness of the salt is obtained by interpolation between the unloaded state and a relevant failure state. The model enables predic...... prediction of short term triaxial behaviour from uniaxial stress-strain curves. Key results from a nonlinear finite element calculation of a gas-filled cavity are given, and the general features are related to a simple nonlinear method of stress evaluation....

The effect of body position on the 'hanging drop' method for identifying the extradural space in anaesthetized dogs.

Science.gov (United States)

Naganobu, Kiyokazu; Hagio, Mitsuyoshi

2007-01-01

To assess the accuracy of the 'hanging drop method' for identifying the extradural space in anaesthetized dogs positioned in sternal or lateral recumbency. Prospective randomized-experimental study. Seventeen clinically healthy adult dogs, 10 females and seven males weighing 8.4-26.2 kg. Dogs were positioned in either sternal (n = 8) or lateral (n = 9) recumbency under general anaesthesia. A 20 SWG spinal needle pre-filled with 0.9% saline was advanced through the skin into the lumbosacral extradural space and the response of the saline drop recorded, i.e. whether it: 1) was aspirated from the hub into the needle; 2) remained within the hub, or 3) moved synchronously with i) spontaneous respiration, ii) heart beat or iii) manual lung inflation. The position of the needle tip was ultimately determined by positive contrast radiography. One dog positioned in lateral recumbency was excluded from the study because bleeding occurred from the needle hub. Saline was aspirated into the needle in seven of eight dogs held in sternal recumbency but in none of the dogs positioned in lateral recumbency. Accurate needle tip placement in the extradural space was confirmed by positive contrast radiography in all dogs. The 'hanging drop' method, when performed with a spinal needle, appears to be a useful technique for identifying the location of the extradural space in anaesthetized medium-sized dogs positioned in sternal, but not in lateral recumbency. The technique may yield 'false negative' results when performed in dogs positioned in sternal recumbency.

Influence of Knee-to-Feet Jump Training on Vertical Jump and Hang Clean Performance.

Science.gov (United States)

Stark, Laura; Pickett, Karla; Bird, Michael; King, Adam C

2016-11-01

Stark, L, Pickett, K, Bird, M, and King, AC. Influence of knee-to-feet jump training on vertical jump and hang clean performance. J Strength Cond Res 30(11): 3084-3089, 2016-From a motor learning perspective, the practice/training environment can result in positive, negative, or neutral transfer to the testing conditions. The purpose of this study was to examine the training effect of a novel movement (knee-to-feet [K2F] jumps) and whether a 6-week training program induced a positive transfer effect to other power-related movements (vertical jump and hang clean [HC]). Twenty-six intercollegiate athletes from power-emphasized sports were paired and counter-balanced into a control (i.e., maintained their respective sport-specific lifting regimen) or an experimental group (i.e., completed a 6-week progressive training program of K2F jumps in addition to respective lifting regimen). A pre- and posttest design was used to investigate the effect of training on K2F jump height and transfer effect to vertical jump height (VJH) and 2-repetition maximum (RM) HC performance. A significant increase in K2F jump height was found for the experimental group. Vertical jump height significantly increased from pre- to posttest but no group or interaction (group × time) effect was found, and there were nonsignificant differences for HC. Posttest data showed significant correlations between all pairs of the selected exercises with the highest correlation between K2F jump height and VJ H (R = 0.40) followed by VJH and 2RM HC (R = 0.38) and 2RM HC and K2F jump height (R = 0.23). The results suggest that K2F jump training induced the desired learning effect but was specific to the movement in that no effect of transfer occurred to the other power-related movements. This finding is value for strength and condition professionals who design training programs to enhance athletic performance.

Seismic response of rock joints and jointed rock mass

International Nuclear Information System (INIS)

Ghosh, A.; Hsiung, S.M.; Chowdhury, A.H.

1996-06-01

Long-term stability of emplacement drifts and potential near-field fluid flow resulting from coupled effects are among the concerns for safe disposal of high-level nuclear waste (HLW). A number of factors can induce drift instability or change the near-field flow patterns. Repetitive seismic loads from earthquakes and thermal loads generated by the decay of emplaced waste are two significant factors. One of two key technical uncertainties (KTU) that can potentially pose a high risk of noncompliance with the performance objectives of 10 CFR Part 60 is the prediction of thermal-mechanical (including repetitive seismic load) effects on stability of emplacement drifts and the engineered barrier system. The second KTU of concern is the prediction of thermal-mechanical-hydrological (including repetitive seismic load) effects on the host rock surrounding the engineered barrier system. The Rock Mechanics research project being conducted at the Center for Nuclear Waste Regulatory Analyses (CNWRA) is intended to address certain specific technical issues associated with these two KTUs. This research project has two major components: (i) seismic response of rock joints and a jointed rock mass and (ii) coupled thermal-mechanical-hydrological (TMH) response of a jointed rock mass surrounding the engineered barrier system (EBS). This final report summarizes the research activities concerned with the repetitive seismic load aspect of both these KTUs

Geotechnical issues and guidelines for storage of compressed air in excavated hard rock caverns

Energy Technology Data Exchange (ETDEWEB)

Allen, R.D.; Doherty, T.J.; Fossum, A.F.

1982-04-01

The results of a literature survey on the stability of excavated hard rock caverns are presented. The objective of the study was to develop geotechnical criteria for the design of compressed air energy storage (CAES) caverns in hard rock formations. These criteria involve geologic, hydrological, geochemical, geothermal, and in situ stress state characteristics of generic rock masses. Their relevance to CAES caverns, and the identification of required research areas, are identified throughout the text. This literature survey and analysis strongly suggests that the chief geotechnical issues for the development and operation of CAES caverns in hard rock are impermeability for containment, stability for sound openings, and hydrostatic balance.

Microelements containing in rock of the Aral region. Agrochemical problems

International Nuclear Information System (INIS)

Zhumamuratov, A.

2004-01-01

Lately chemization of agriculture has been done not only by mineral nitrification and pesticides but also by melioration with rocks and industrial waste. However, increase in soil fertility and the related efficiency of production requires systematic control and analysis of the chemization so as not to disturb the existing balance in ecosystem. The experiment on bringing mountain rocks up 30 ton/hectare in soil shows that the socks have variable element contents (up a few orders of value) and under this condition the soil may be poisoned with undesirable toxic elements. Thus, it becomes actual to analyse the total element contents of soil and the inserted meliorants (rocks and other resources available in the region) used in agriculture production. Besides, the obtained information about element contents of mountain rocks allows to solve not only geochemical problems but also to evaluate soil formation process. Choose of a mountain rock having soil. Lack of microelements in soil can be made up by fitting optimal doses of meliorants consisting of mineral (NPK) and local fertilizers, mountain rocks or industrial waste. We proved earlier, that the soils of cotton planting area of Uzbekistan are exhausted with the nutrient elements (Co, Fe, Zn, Cu, Mn, Mo, Rb, Cs, K and rarer P). Besides, the soil are polluted with As, Sb, Br, U, Th, REE and the Republics. Owing to pollution of the region soil with toxic elements, deficit of the nutritious in the environment, one can expect progressing of several diseases (sick ratr) in the population. Relating to the update agro-state of the soil of cotton planting region of Karakalpakstan, one can observe similar agrogeochemical processes complicated by a sharp accumulation on Na and Cl in subsurface layers of the soil. On the territory of the South Aral at different depths of many chinks and paleogenic terrigenic thick being opened in hills of Krantau, Khoja-Kul, Beshtube, Khojeily and also in the South-East Sultanuezdag, there are

Microelements containing in rock of the Aral region. Agrogeochemical problems

International Nuclear Information System (INIS)

Zhumamuratov, A.

2004-01-01

Full text: Lately chemization of agriculture has been done not only by mineral nutrification and pesticides but also by melioration with rocks and industrial waste. However, increase in soil fertility and the related efficiency of production requires systematic control and analysis of the chemization so as not to disturb the existing balance in ecosystem. The experiment on bringing mountain rocks up 30ton/hectare in soil shows that the socks have variable element contents (up a few orders of value) and under this condition the soil may be poisoned with undesirable toxic elements. Thus, it becomes actual to analyse the total element contents of soil and the inserted meliorants (rocks and other resources available in the region) used in agriculture production. Besides, the obtained information about element contents of mountain rocks allows to solve not only geochemical problems but also to evaluate soil formation process. Choose of a mountain rock having soil. Lack of microelements in soil can be made up by fitting optimal doses of meliorants consisting of mineral (NPK) and local fertilizers, mountain rocks or industrial waste. We proved earlier, that the soils of cotton planting area of Uzbekistan are exhausted with the nutrient elements (Co, Fe, Zn, Cu, Mn, Mo, Rb, Cs, K and rarer P). Besides, the soil are polluted with As, Sb, Br, U, Th, REE and the Republics. Owing to pollution of the region soil with toxic elements, deficit of the nutritious in the environment, one can expect progressing of several diseases (sick ratr) in the population. Relating to the update agro-state of the soil of cotton planting region of Karakalpakstan, one can observe similar agrogeochemical processes complicated by a sharp accumulation on Na and Cl in subsurface layers of the soil. On the territory of the South Aral at different depths of many chinks and paleogenic terrigenic thick being opened in hills of Krantau, Khoja-Kul, Beshtube, Khojeily and also in the South-East Sultanuezdag

Building a sustainable land public transportation at Ayer Keroh, Malacca: Perspective view from hang tuah jaya municipal council (HTJMC)

Science.gov (United States)

Sukri, Fatin Hafizah; Chew, Boon Cheong; Hamid, Syaiful Rizal; Loo, Heoy Shin

2017-03-01

Sustainable land public transportation (SLPT) aims to promote a better and healthier ways of meeting individual and community needs. Even though sufficient land public transportation have been provided at Ayer Keroh, Malacca but the level of usage among the community is still low as there is the growth in traffic. Hang Tuah Jaya Municipal Council (HTJMC) is responsible to identify the most appropriate strategies to manage the issues regarding SLPT in order to support of the Malacca state vision becoming Green Technology State in the year 2020. Therefore, this paper attempts to examine the strategies involve in building a SLPT, which may enhance the community's welfare. Thus, the proposed theoretical framework is to demonstrate the strategies towards building a SLPT, which can cater issues within the municipal council area. In this qualitative research, an in-depth focus group have been conducted to obtain the primary data. Thirteen (13) executives from HTJMC involved. This study brings a new paradigm in transforming land public transportation at Ayer Keroh to enhance the community welfare. The result found that land use development as the most significant strategy in SLPT, meanwhile the implementation program is the least strategy involved in building a SLPT at Ayer Keroh. Future research requires more information on the factors of implementing of SLPT so that HTJMC can plan an effective SLPT thorough the demand as the data may indicate numbers of passengers who really support to the implementation of SLPT.

Effects of confinement on rock mass modulus: A synthetic rock mass modelling (SRM study

Directory of Open Access Journals (Sweden)

I. Vazaios

2018-06-01

Full Text Available The main objective of this paper is to examine the influence of the applied confining stress on the rock mass modulus of moderately jointed rocks (well interlocked undisturbed rock mass with blocks formed by three or less intersecting joints. A synthetic rock mass modelling (SRM approach is employed to determine the mechanical properties of the rock mass. In this approach, the intact body of rock is represented by the discrete element method (DEM-Voronoi grains with the ability of simulating the initiation and propagation of microcracks within the intact part of the model. The geometry of the pre-existing joints is generated by employing discrete fracture network (DFN modelling based on field joint data collected from the Brockville Tunnel using LiDAR scanning. The geometrical characteristics of the simulated joints at a representative sample size are first validated against the field data, and then used to measure the rock quality designation (RQD, joint spacing, areal fracture intensity (P21, and block volumes. These geometrical quantities are used to quantitatively determine a representative range of the geological strength index (GSI. The results show that estimating the GSI using the RQD tends to make a closer estimate of the degree of blockiness that leads to GSI values corresponding to those obtained from direct visual observations of the rock mass conditions in the field. The use of joint spacing and block volume in order to quantify the GSI value range for the studied rock mass suggests a lower range compared to that evaluated in situ. Based on numerical modelling results and laboratory data of rock testing reported in the literature, a semi-empirical equation is proposed that relates the rock mass modulus to confinement as a function of the areal fracture intensity and joint stiffness. Keywords: Synthetic rock mass modelling (SRM, Discrete fracture network (DFN, Rock mass modulus, Geological strength index (GSI, Confinement

The Spatial Assessment of the Current Seismic Hazard State for Hard Rock Underground Mines

Science.gov (United States)

Wesseloo, Johan

2018-06-01

Mining-induced seismic hazard assessment is an important component in the management of safety and financial risk in mines. As the seismic hazard is a response to the mining activity, it is non-stationary and variable both in space and time. This paper presents an approach for implementing a probabilistic seismic hazard assessment to assess the current hazard state of a mine. Each of the components of the probabilistic seismic hazard assessment is considered within the context of hard rock underground mines. The focus of this paper is the assessment of the in-mine hazard distribution and does not consider the hazard to nearby public or structures. A rating system and methodologies to present hazard maps, for the purpose of communicating to different stakeholders in the mine, i.e. mine managers, technical personnel and the work force, are developed. The approach allows one to update the assessment with relative ease and within short time periods as new data become available, enabling the monitoring of the spatial and temporal change in the seismic hazard.

Laser scattering in a hanging drop vapor diffusion apparatus for protein crystal growth in a microgravity environment

Science.gov (United States)

Casay, G. A.; Wilson, W. W.

1992-01-01

One type of hardware used to grow protein crystals in the microgravity environment aboard the U.S. Space Shuttle is a hanging drop vapor diffusion apparatus (HDVDA). In order to optimize crystal growth conditions, dynamic control of the HDVDA is desirable. A critical component in the dynamically controlled system is a detector for protein nucleation. We have constructed a laser scattering detector for the HDVDA capable of detecting the nucleation stage. The detector was successfully tested for several scatterers differing in size using dynamic light scattering techniques. In addition, the ability to detect protein nucleation using the HDVDA was demonstrated for lysozyme.

Rock Physical Interpretation of the Relationship between Dynamic and Static Young's Moduli of Sedimentary Rocks

Science.gov (United States)

Takahashi, T.

2017-12-01

The static Young's modulus (deformability) of a rock is indispensable for designing and constructing tunnels, dams and underground caverns in civil engineering. Static Young's modulus which is an elastic modulus at large strain level is usually obtained with the laboratory tests of rock cores sampled in boreholes drilled in a rock mass. A deformability model of the entire rock mass is then built by extrapolating the measurements based on a rock mass classification obtained in geological site characterization. However, model-building using data obtained from a limited number of boreholes in the rock mass, especially a complex rock mass, may cause problems in the accuracy and reliability of the model. On the other hand, dynamic Young's modulus which is the modulus at small strain level can be obtained from seismic velocity. If dynamic Young's modulus can be rationally converted to static one, a seismic velocity model by the seismic method can be effectively used to build a deformability model of the rock mass. In this study, we have, therefore, developed a rock physics model (Mavko et al., 2009) to estimate static Young's modulus from dynamic one for sedimentary rocks. The rock physics model has been generally applied to seismic properties at small strain level. In the proposed model, however, the sandy shale model, one of rock physics models, is extended for modeling the static Young's modulus at large strain level by incorporating the mixture of frictional and frictionless grain contacts into the Hertz-Mindlin model. The proposed model is verified through its application to the dynamic Young's moduli derived from well log velocities and static Young's moduli measured in the tri-axial compression tests of rock cores sampled in the same borehole as the logs were acquired. This application proves that the proposed rock physics model can be possibly used to estimate static Young's modulus (deformability) which is required in many types of civil engineering applications

Finite Element Analysis of the Effect on Edge Distance of the Tensile Bearing Capacity of Embedded Hanging Parts

Directory of Open Access Journals (Sweden)

Meng Xian Hong

2016-01-01

Full Text Available In order to explore the trend of tensile bearing capacity of embedded hanging parts when change the edge distance. Based on the finite element analysis software ABAQUS, the four simulation model was established. The buried depth and strength of concrete remain unchanged, but the edge distance was gradient change. By the load - displacement curve of every model known, the greater the edge distance, the greater the bearing capacity. When the edge distance reaches 1.5 times buried depth, the effect of increasing edge distance for improving the bearing capacity will be impaired.

Voltammetric behavior of amfepramone (diethylpropion) at the hanging mercury drop electrode and its analytical determination in pharmaceutical formulations

OpenAIRE

Carvalho, Leandro M. de; Nascimento, Paulo C. do; Bohrer, Denise; Correia, Daniele; Bairros, André V. de; Pomblum, Valdeci J.; Pomblum, Solange G.

2007-01-01

This paper describes a systematic study of the voltammetric behavior of amfepramone at the hanging mercury drop electrode (HMDE) by cyclic (CV) and alternating current (AC) voltammetric methods. The studies showed the adsorptive behavior of amfepramone at the HMDE and were performed in H2SO4 0.1 mol L-1 (pH 1.0) and Ringer buffer (pH 11.0) as supporting electrolytes. The linear range for the amfepramone determination by differential pulse voltammetry (DPV) was 0.05 to 2.0 mg L-1 (r = 0.998) i...

No Reprieve for Tasmanian Rock Art

Directory of Open Access Journals (Sweden)

Peter C. Sims

2013-10-01

Full Text Available The Australian State of Tasmania, at latitude 42 degrees south, became an island about 8,000 years ago when the sea rose to its present level, following the melting of polar and glacial ice that covered much of the land mass. After that time, the Tasmanian Aboriginal rock art developed independently of mainland Australia, with its form being basically linear with some naturalistic figures and a predominance of cupules. The petroglyphs with one lithophone site occur on various rock substrates varying in hardness from granite to sandstone. Many sites exist along the western coastline that borders the Southern Ocean where the landscape in some places has changed little since the arrival of Europeans in 1803. The significance of this Tasmanian Aboriginal cultural heritage along what is now known as the Tarkine Coast, named after an Aboriginal band that once inhabited this area, was recognised by the Australian Government in February 2013 when a 21,000 ha strip, 2 km wide, was inscribed on its National Heritage Register, being one of 98 special places listed in the country. However, politics and racism hamper its management. This paper is based on the results of 40 years of field recording of the Tasmanian Aboriginal rock art sites, many of which remain unpublished.

The Rock Cycle

Science.gov (United States)

Singh, Raman J.; Bushee, Jonathan

1977-01-01

Presents a rock cycle diagram suitable for use at the secondary or introductory college levels which separates rocks formed on and below the surface, includes organic materials, and separates products from processes. (SL)

Water-rock interaction in a high-FeO olivine rock in nature

International Nuclear Information System (INIS)

Hellmuth, K.H.; Lindberg, A.; Tullborg, E.L.

1992-12-01

The long-term behaviour in nature of high-FeO olivine rock in contact with surface water has been studied at the Lovasjaervi instrusion, SE-Finland. The rock has been proposed as a high-capasity, higly reactive redox-buffer backfill in a repository for spent fuel. Favourable groundwater chemistry is a major parameter relevant to safety of such a repository. Reducing conditions favour the retardation of long-lived, redox-sensitive radionuclides. Weathering influences have been studied at the natural outcrop of the rock mass. The interaction of oxidizing surface waters with rock at greater depths has been studied by using fissure filling minerals. Investigation of weathered rock from the outcrop indicates that the olivine rock is highly reactive on a geological time scale and its redox capasity is available although the instrusion as a whole is surprisingly well preserved. The fissure fillings studied allow the conclusion that oxygen seems to be efficiently removed from intruding surface water. Oxidation seem to have caused visible effects only along very conducting fractures and near the contact zones of the surrounding granitic rock. Stable isotope data of fissure filling calcites indicate that the influence of surface waters can be traced clearly down to a depth of about 50 m, but also at greater depths re-equilibration has occurred. Groundwater data from the site were not available. (orig.)

Cecal bacterial communities in wild Japanese rock ptarmigans and captive Svalbard rock ptarmigans.

Science.gov (United States)

Ushida, Kazunari; Segawa, Takahiro; Tsuchida, Sayaka; Murata, Koichi

2016-02-01

Preservation of indigenous gastrointestinal microbiota is deemed to be critical for successful captive breeding of endangered wild animals, yet its biology is poorly understood. Here, we investigated cecal bacterial communities in wild Japanese rock ptarmigans (Lagopus muta japonica) and compared them with those in Svalbard rock ptarmigans (L. m. hyperborea) in captivity. Ultra-deep sequencing of 16S rRNA gene indicated that the community structure of cecal microbiota in wild rock ptarmigans was remarkably different from that in captive Svalbard rock ptarmigans. Fundamental differences between bacterial communities in the two groups of birds were detected at the phylum level. Firmicutes, Actinobacteria, Bacteroidetes and Synergistetes were the major phyla detected in wild Japanese rock ptarmigans, whereas Firmicutes alone occupied more than 80% of abundance in captive Svalbard rock ptarmigans. Furthermore, unclassified genera of Coriobacteriaceae, Synergistaceae, Bacteroidaceae, Actinomycetaceae, Veillonellaceae and Clostridiales were the major taxa detected in wild individuals, whereas in zoo-reared birds, major genera were Ruminococcus, Blautia, Faecalibacterium and Akkermansia. Zoo-reared birds seemed to lack almost all rock ptarmigan-specific bacteria in their intestine, which may explain the relatively high rate of pathogenic infections affecting them. We show evidence that preservation and reconstitution of indigenous cecal microflora are critical for successful ex situ conservation and future re-introduction plan for the Japanese rock ptarmigan.

Rock engineering in Finland

Energy Technology Data Exchange (ETDEWEB)

1986-01-01

Contains a large collection of short articles concerned with tunnels and underground caverns and their construction and use. The articles are grouped under the following headings: use of the subsurface space; water supply; waste water services; energy management (includes articles on power stations, district heating and oil storage and an article on coal storage); multipurpose tunnels; waste disposal; transport; shelters; sporting and recreational amenities located in rock caverns; storage facilities; industrial, laboratory, and service facilities; rock foundations; tourism and culture; utilization of rock masses; research on the disposal of nuclear waste; training and research in the field of rock engineering; site investigation techniques; design of structures in rock; construction; the environment and occupational safety; modern equipment technology; underground space in Helsinki.

Triaxial slide-hold-slide shear experiment of sedimentary rock under drain condition

International Nuclear Information System (INIS)

Kishida, Kiyoshi; Yano, Takao; Elsworth, Derek; Yasuhara, Hideaki; Nakashima, Shinichiro

2011-01-01

When discussing the mechanical and hydro-mechanical properties of rock masses under the long-term holding, the variation of rock structure and the change of shear band condition should be discussed in considering the effect of thermal and chemical influences. In this research, the triaxial shear experiment under drain condition was conducted through sedimentary rock, and in the residual stress state, the slide-hold-slide processes were applied to these triaxial experiments. The experiments were carried out in 3 kinds of confining conditions and 2 kinds of thermal conditions. Consequently, the healing phenomena can be observed and the shear strength recovery is also confirmed in process of the holding time. (author)

Characterization of deep-seated rock masses by means of borehole investigation

International Nuclear Information System (INIS)

1982-04-01

Swedish State Power Board. The main objective of the programme was to test a method of measuring in-situ rock stresses in the deep, water-filled boreholes and to correlate measured rock stresses with the hydraulic and geological properties of the rock mass. The investigations consist of the following activities: - Coredrillin of two main boreholes with a depth of 500 m and 250 m respectively. - Rock stress measurements at 11 and 9 main levels in the boreholes respectively. At each level at least 3 complete measurements were made. - Logging of the cores with respect to rock type, fractures and fracture characteristics. - Water injection tests in the boreholes. The rock mass investigated is composed of a gneiss granite of Svecocarelian age (1500 Ma), with inclusions of younger pegmatites and greenstones of variable ages. The fracture density is as a mean 2 fractures per meter with a marked decrease in frequency with increased depth. The fractures are generally coated with calcite and chlorite as the dominating coating minerals. For the rock stress measurements, the method of Leeman and Hayes was chosen. The result show that there is a very high stress level in the rock mass, recordings of about 70 MPa were taken below a horizontal fracture zone at 320 m depth. In this lower rock masses the high stresses were also illustrated by intense disking of the hollow core which made measurements impossible in large sections of the boreholes. Water injection tests were performed, mainly as double-packer tests alon the entire boreholes. For the evaluation, both stationary and transient calculation theories were used and the results show a good agreement. The hyddraulic conductivities of the rock mass vary from below 10 -10 m/s up to 10 -7 m/s. The conductivity decreases with depth, though there are zones even at great depth with high conductivity. (Author)

Sliding rocks on Racetrack Playa, Death Valley National Park: first observation of rocks in motion.

Directory of Open Access Journals (Sweden)

Richard D Norris

Full Text Available The engraved trails of rocks on the nearly flat, dry mud surface of Racetrack Playa, Death Valley National Park, have excited speculation about the movement mechanism since the 1940s. Rock movement has been variously attributed to high winds, liquid water, ice, or ice flotation, but has not been previously observed in action. We recorded the first direct scientific observation of rock movements using GPS-instrumented rocks and photography, in conjunction with a weather station and time-lapse cameras. The largest observed rock movement involved > 60 rocks on December 20, 2013 and some instrumented rocks moved up to 224 m between December 2013 and January 2014 in multiple move events. In contrast with previous hypotheses of powerful winds or thick ice floating rocks off the playa surface, the process of rock movement that we have observed occurs when the thin, 3 to 6 mm, "windowpane" ice sheet covering the playa pool begins to melt in late morning sun and breaks up under light winds of -4-5 m/s. Floating ice panels 10 s of meters in size push multiple rocks at low speeds of 2-5 m/min. along trajectories determined by the direction and velocity of the wind as well as that of the water flowing under the ice.

A Discrete Element Method Approach to Progressive Localization of Damage in Granular Rocks and Associated Seismicity

Science.gov (United States)

Vora, H.; Morgan, J.

2017-12-01

Brittle failure in rock under confined biaxial conditions is accompanied by release of seismic energy, known as acoustic emissions (AE). The objective our study is to understand the influence of elastic properties of rock and its stress state on deformation patterns, and associated seismicity in granular rocks. Discrete Element Modeling is used to simulate biaxial tests on granular rocks of defined grain size distribution. Acoustic Energy and seismic moments are calculated from microfracture events as rock is taken to conditions of failure under different confining pressure states. Dimensionless parameters such as seismic b-value and fractal parameter for deformation, D-value, are used to quantify seismic character and distribution of damage in rock. Initial results suggest that confining pressure has the largest control on distribution of induced microfracturing, while fracture energy and seismic magnitudes are highly sensitive to elastic properties of rock. At low confining pressures, localized deformation (low D-values) and high seismic b-values are observed. Deformation at high confining pressures is distributed in nature (high D-values) and exhibit low seismic b-values as shearing becomes the dominant mode of microfracturing. Seismic b-values and fractal D-values obtained from microfracturing exhibit a linear inverse relationship, similar to trends observed in earthquakes. Mode of microfracturing in our simulations of biaxial compression tests show mechanistic similarities to propagation of fractures and faults in nature.

Hanging drop cultures of human testis and testis cancer samples: a model used to investigate activin treatment effects in a preserved niche.

Science.gov (United States)

Jørgensen, A; Young, J; Nielsen, J E; Joensen, U N; Toft, B G; Rajpert-De Meyts, E; Loveland, K L

2014-05-13

Testicular germ cell tumours of young adults, seminoma or non-seminomas, are preceded by a pre-invasive precursor, carcinoma in situ (CIS), understood to arise through differentiation arrest of embryonic germ cells. Knowledge about the malignant transformation of germ cells is currently limited by the lack of experimental models. The aim of this study was to establish an experimental tissue culture model to maintain normal and malignant germ cells within their niche and allow investigation of treatment effects. Human testis and testis cancer specimens from orchidectomies were cultured in 'hanging drops' and effects of activin A and follistatin treatment were investigated in seminoma cultures. Testis fragments with normal spermatogenesis or CIS cells were cultured for 14 days with sustained proliferation of germ cells and CIS cells and without increased apoptosis. Seminoma cultures survived 7 days, with proliferating cells detectable during the first 5 days. Activin A treatment significantly reduced KIT transcript and protein levels in seminoma cultures, thereby demonstrating a specific treatment response. Hanging drop cultures of human testis and testis cancer samples can be employed to delineate mechanisms governing growth of normal, CIS and tumorigenic germ cells retained within their niche.

Rock Mechanics Forsmark. Site descriptive modelling Forsmark stage 2.2

Energy Technology Data Exchange (ETDEWEB)

Glamheden, Rune; Fredriksson, Anders (Golder Associates AB (SE)); Roeshoff, Kennert; Karlsson, Johan (Berg Bygg Konsult AB (SE)); Hakami, Hossein (Itasca Geomekanik AB (SE)); Christiansson, Rolf (Swedish Nuclear Fuel and Waste Management Co., Stockholm (SE))

2007-12-15

The Swedish Nuclear Fuel and Waste Management Company (SKB) is undertaking site characterisation at two different locations, Forsmark and Laxemar/Simpevarp, with the objective of siting a geological repository for spent nuclear fuel. The characterisation of a site is an integrated work carried out by several disciplines including geology, rock mechanics, thermal properties, hydrogeology, hydrogeochemistry and surface systems. This report presents the rock mechanics model of the Forsmark site up to stage 2.2. The scope of work has included compilation and analysis of primary data of intact rock and fractures, estimation of the rock mass mechanical properties and estimation of the in situ state of stress at the Forsmark site. The laboratory results on intact rock and fractures in the target volume demonstrate a good quality rock mass that is strong, stiff and relatively homogeneous. The homogeneity is also supported by the lithological and the hydrogeological models. The properties of the rock mass have been initially estimated by two separate modelling approaches, one empirical and one theoretical. An overall final estimate of the rock mass properties were achieved by integrating the results from the two models via a process termed 'Harmonization'. Both the tensile tests, carried out perpendicular and parallel to the foliation, and the theoretical analyses of the rock mass properties in directions parallel and perpendicular to the major principal stress, result in parameter values almost independent of direction. This indicates that the rock mass in the target volume is isotropic. The rock mass quality in the target volume appears to be of high and uniform quality. Those portions with reduced rock mass quality that do exist are mainly related to sections with increased fracture frequency. Such sections are associated with deformation zones according to the geological description. The results of adjacent rock domains and fracture domains of the target

Microscopic study of rock for estimating long-term behavior

International Nuclear Information System (INIS)

Ichikawa, Yasuaki

1997-03-01

One must consider micro-structures of rock and rock mass in order to predict the long-term behavior for more than ten thousand years. First we observe the micro-crack distribution of granite which is commonly distributed in Japan, and is widely used for several structures. The creep under constant load and the relaxation under constant displacement are typical time dependent phenomena, and we performed a series of relaxation tests under microscope observation in laboratory. The specimen that is preserved in water is granite as mentioned above. The aim of this experiment is to observe the sequential propagation of micro-cracks and its affect to the macroscopic response of the rock material under relaxation state. Next, a viscoelastic homogenization method is applied for analyzing the behavior of granite that is composed of several kinds of minerals (i.e., a polycrystalline material). The homogenization method developed for analyzing mechanics of composite materials is a mathematical theory that can describe the macroscopic behavior accounting for the microscopic characteristics with periodic microstructures. In this study, it is applied to a polycrystalline rock which involves a few minerals and micro-cracks. Furthermore, it is required to apply the homogenization analysis for rock materials which show a nonlinear time dependent behavior, so we develop a new elasto-visco-plastic homogenization theory, and its validity is checked for some ground structures made by clay. (author)

Hydraulic fracturing of rock-fill dam

Directory of Open Access Journals (Sweden)

Jun-Jie WANG

2016-02-01

Full Text Available The condition in which hydraulic fracturing in core of earth-rock fill dam maybe induced, the mechanism by which the reason of hydraulic fracturing canbe explained, and the failure criterion by which the occurrence of hydraulicfracturing can be determined, were investigated. The condition dependson material properties such as, cracks in the core and low permeability ofcore soil, and “water wedging” action in cracks. An unsaturated core soiland fast impounding are the prerequisites for the formation of “waterwedging” action. The mechanism of hydraulic fracturing can be explainedby fracture mechanics. The crack propagation induced by water pressuremay follow any of mode I, mode II and mixed mode I-II. Based on testingresults of a core soil, a new criterion for hydraulic fracturing was suggested,from which mechanisms of hydraulic fracturing in the core of rock-fill damwere discussed. The results indicated that factors such as angle betweencrack surface and direction of principal stress, local stress state at thecrack, and fracture toughness KIC of core soil may largely affect theinduction of hydraulic fracturing and the mode of the propagation of thecrack.The condition in which hydraulic fracturing in core of earth-rock fill dam maybe induced, the mechanism by which the reason of hydraulic fracturing canbe explained, and the failure criterion by which the occurrence of hydraulicfracturing can be determined, were investigated. The condition dependson material properties such as, cracks in the core and low permeability ofcore soil, and “water wedging” action in cracks. An unsaturated core soiland fast impounding are the prerequisites for the formation of “waterwedging” action. The mechanism of hydraulic fracturing can be explainedby fracture mechanics. The crack propagation induced by water pressuremay follow any of mode I, mode II and mixed mode I-II. Based on testingresults of a core soil, a new criterion for hydraulic fracturing

Rock stresses (Grimsel rock laboratory)

International Nuclear Information System (INIS)

Pahl, A.; Heusermann, S.; Braeuer, V.; Gloeggler, W.

1989-01-01

On the research and development project 'Rock Stress Measurements' the BGR has developed and tested several test devices and methods at GTS for use in boreholes at a depth of 200 m and has carried out rock mechanical and engineering geological investigations for the evaluation and interpretation of the stress measurements. The first time a computer for data processing was installed in the borehole together with the BGR-probe. Laboratory tests on hollow cylinders were made to study the stress-deformation behavior. To validate and to interprete the measurement results some test methods were modelled using the finite-element method. The dilatometer-tests yielded high values of Young's modulus, whereas laboratory tests showed lower values with a distinct deformation anisotropy. Stress measurements with the BGR-probe yielded horizontal stresses being higher than the theoretical overburden pressure and vertical stresses which agree well with the theoretical overburden pressure. These results are comparable to the results of the hydraulic fracturing tests, whereas stresses obtained with CSIR-triaxial cells are generally lower. The detailed geological mapping of the borehole indicated relationships between stress and geology. With regard to borehole depth different zones of rock structure joint frequency, joint orientation, and orientation of microfissures as well as stress magnitude, stress direction, and degree of deformation anisotropy could be distinguished. (orig./HP) [de

Appraisal of hard rock for potential underground repositories of radioactive wastes. LBL-7004

International Nuclear Information System (INIS)

Cook, N.G.W.

1978-01-01

Underground burial of radioactive wastes in hard rock may be an effective and safe means of isolating them from the environment and from man. The mechanical safety and stability of such an underground repository depends largely on the virgin state of stress in the rock, groundwater pressures, the strengths of the rocks, heating by the decay of the radioactive wastes, and the layout of the excavations and the disposition of waste cannisters within them. A large body of pertinent data exists in the literature, and each of these factors has been analyzed in the light of this information. The results indicate that there are no fundamental geological nor mechanical reasons why repositories capable of storing radioactive wastes should not be excavated at suitable sites in hard rock. However, specific tests to determine the mechanical and thermal properties of the rocks at a site would be needed to provide the data for the engineering design of a repository. Also, little experience exists of the effects on underground excavations of thermal loads, so that this aspect requires theoretical study and experimental validation. The depths of these potential repositories would lie in the range from 0.5 km to 2.0 km below surface, depending upon the strength of the rock. Virgin states of stress have been measured at such depths which would retard the ingress of groundwater and obviate the incidence of faulting. A typical repository comprising three horizons each with a total area of 5 km 2 would have the capacity to store wastes with thermal output of 240 MW

Review on the prevailing methods for the prediction of potential rock burst / rock spalling in tunnels

OpenAIRE

Panthi, Krishna Kanta

2017-01-01

Rock burst / rock spalling is among the prevailing stability challenges, which can be met while tunneling through hard rock mass. Especially, this is very relevant for the mountainous country like Norway where hard rock is dominating and many road, railway and hydropower tunnels have to be aligned deep into the mountain with steep valley slope topography. Tunnels passing beneath deep rock cover (overburden), in general, are subjected to high in-situ stresses. If the rock mass is relatively un...

Synthetic Rock Analogue for Permeability Studies of Rock Salt with Mudstone

Directory of Open Access Journals (Sweden)

Hongwu Yin

2017-09-01

Full Text Available Knowledge about the permeability of surrounding rock (salt rock and mudstone interlayer is an important topic, which acts as a key parameter to characterize the tightness of gas storage. The goal of experiments that test the permeability of gas storage facilities in rock salt is to develop a synthetic analogue to use as a permeability model. To address the permeability of a mudstone/salt layered and mixed rock mass in Jintan, Jiangsu Province, synthetic mixed and layered specimens using the mudstone and the salt were fabricated for permeability testing. Because of the gas “slippage effect”, test results are corrected by the Klinkenberg method, and the permeability of specimens is obtained by regression fitting. The results show that the permeability of synthetic pure rock salt is 6.9 × 10−20 m2, and its porosity is 3.8%. The permeability of synthetic mudstone rock is 2.97 × 10−18 m2, with a porosity 17.8%. These results are close to those obtained from intact natural specimens. We also find that with the same mudstone content, the permeability of mixed specimens is about 40% higher than for the layered specimens, and with an increase in the mudstone content, the Klinkenberg permeability increases for both types of specimens. The permeability and mudstone content have a strong exponential relationship. When the mudstone content is below 40%, the permeability increases only slightly with mudstone content, whereas above this threshold, the permeability increases rapidly with mudstone content. The results of the study are of use in the assessment of the tightness of natural gas storage facilities in mudstone-rich rock salt formations in China.

Dissolved methane oxidation and competition for oxygen in down-flow hanging sponge reactor for post-treatment of anaerobic wastewater treatment

OpenAIRE

Hatamoto, Masashi; Miyauchi, Tomo; Kindaichi, Tomonori; Ozaki, Noriatsu; Ohashi, Akiyoshi

2011-01-01

Post-treatment of anaerobic wastewater was undertaken to biologically oxidize dissolved methane, with the aim of preventing methane emission. The performance of dissolved methane oxidation and competition for oxygen among methane, ammonium, organic matter, and sulfide oxidizing bacteria were investigated using a lab-scale closed-type down-flow hanging sponge (OHS) reactor. Under the oxygen abundant condition of a hydraulic retention time of 2 h and volumetric air supply rate of 12.95 m(3)-air...

Etiology and use of the "hanging drop" technique: a review.

Science.gov (United States)

Todorov, Ludmil; VadeBoncouer, Timothy

2014-01-01

Background. The hanging drop (HD) technique presumably relies on the presence of subatmospheric epidural pressure. It is not clear whether this negative pressure is intrinsic or an artifact and how it is affected by body position. There are few data to indicate how often HD is currently being used. Methods. We identified studies that measured subatmospheric pressures and looked at the effect of the sitting position. We also looked at the technique used for cervical and thoracic epidural anesthesia in the last 10 years. Results. Intrinsic subatmospheric pressures were measured in the thoracic and cervical spine. Three trials studied the effect of body position, indicating a higher incidence of subatmospheric pressures when sitting. The results show lower epidural pressure (-10.7 mmHg) with the sitting position. 28.8% of trials of cervical and thoracic epidural anesthesia that documented the technique used, utilized the HD technique. When adjusting for possible bias, the rate of HD use can be as low as 11.7%. Conclusions. Intrinsic negative pressure might be present in the cervical and thoracic epidural space. This effect is more pronounced when sitting. This position might be preferable when using HD. Future studies are needed to compare it with the loss of resistance technique.

Digital Rock Simulation of Flow in Carbonate Samples

Science.gov (United States)

Klemin, D.; Andersen, M.

2014-12-01

Reservoir engineering has becomes more complex to deal with current challenges, so core analysts must understand and model pore geometries and fluid behaviors at pores scales more rapidly and realistically. We introduce an industry-unique direct hydrodynamic pore flow simulator that operates on pore geometries from digital rock models obtained using microCT or 3D scanning electron microscope (SEM) images. The PVT and rheological models used in the simulator represent real reservoir fluids. Fluid-solid interactions are introduced using distributed micro-scale wetting properties. The simulator uses density functional approach applied for hydrodynamics of complex systems. This talk covers selected applications of the simulator. We performed microCT scanning of six different carbonate rock samples from homogeneous limestones to vuggy carbonates. From these, we constructed digital rock models representing pore geometries for the simulator. We simulated nonreactive tracer flow in all six digital models using a digital fluid description that included a passive tracer solution. During the simulation, we evaluated the composition of the effluent. Results of tracer flow simulations corresponded well with experimental data of nonreactive tracer floods for the same carbonate rock types. This simulation data of the non-reactive tracer flow can be used to calculate the volume of the rock accessible by the fluid, which can be further used to predict response of a porous medium to a reactive fluid. The described digital core analysis workflow provides a basis for a wide variety of activities, including input to design acidizing jobs and evaluating treatment efficiency and EOR economics. Digital rock multiphase flow simulations of a scanned carbonate rock evaluated the effect of wettability on flow properties. Various wetting properties were tested: slightly oil wet, slightly water wet, and water wet. Steady-state relative permeability simulations yielded curves for all three

Evolution Procedure of Multiple Rock Cracks under Seepage Pressure

Directory of Open Access Journals (Sweden)

Taoying Liu

2013-01-01

Full Text Available In practical geotechnical engineering, most of rock masses with multiple cracks exist in water environment. Under such circumstance, these adjacent cracks could interact with each other. Moreover, the seepage pressure, produced by the high water pressure, can change cracks’ status and have an impact on the stress state of fragile rocks. According to the theory of fracture mechanics, this paper discusses the law of crack initiation and the evolution law of stress intensity factor at the tip of a wing crack caused by compression-shear stress and seepage pressure. Subsequently, considering the interaction of the wing cracks and the additional stress caused by rock bridge damage, this paper proposes the intensity factor evolution equation under the combined action of compression-shear stress and seepage pressure. In addition, this paper analyzes the propagation of cracks under different seepage pressure which reveals that the existence of seepage pressure facilitates the wing crack’s growth. The result indicates that the high seepage pressure converts wing crack growth from stable form to unstable form. Meanwhile, based on the criterion and mechanism for crack initiation and propagation, this paper puts forward the mechanical model for different fracture transfixion failure modes of the crag bridge under the combined action of seepage pressure and compression-shear stress. At the last part, this paper, through investigating the flexibility tensor of the rock mass’s initial damage and its damage evolution in terms of jointed rock mass's damage mechanics, deduces the damage evolution equation for the rock mass with multiple cracks under the combined action of compression-shear stress and seepage pressure. The achievement of this investigation provides a reliable theoretical principle for quantitative research of the fractured rock mass failure under seepage pressure.

Ground water movements around a repository. Rock mechanics analyses

International Nuclear Information System (INIS)

Ratigan, J.L.

1977-09-01

The determination and rational assessment of groundwater flow around a repository depends upon the accurate analysis of several interdependent and coupled phenomenological events occuring within the rock mass. In particular, the groundwater flow pathways (joints) are affected by the excavation and thermomechanical stresses developed within the rock mass, and the properties, of the groundwater are altered by the temperature perturbations in the rock mass. The objective of this report is to present the results of the rock mechanics analysis for the repository excavation and the thermally-induced loadings. Qualitative analysis of the significance of the rock mechanics results upon the groundwater flow is provided in this report whenever such an analysis can be performed. Non-linear rock mechanics calculations have been completed for the repository storage tunnels and the global repository domain. The rock mass has been assumed to possess orthoganol joint sets or planes of weakness with finite strength characteristics. In the local analyses of the repository storage tunnels the effects of jointorientation and repository ventilation have been examined. The local analyses indicated that storage room support requirements and regions of strength failure are highly dependent upon joint orientation. The addition of storage tunnel ventilation was noted to reduce regions of strength failure, particularly during the 30 year operational phase of the repository. Examination of the local stresses around the storage tunnels indicated the potential for perturbed hydraulic permeabilities. The permeabilities can be expected to be altered to a greater degree by the stresses resulting from excavation than from stresses which are thermally induced. The thermal loading provided by the instantaneous waste emplacement resulted in stress states and displacements quite similar to those provided by the linear waste emplacement sequence

'Mister Badger' Pushing Mars Rock

Science.gov (United States)

1976-01-01

Viking's soil sampler collector arm successfully pushed a rock on the surface of Mars during the afternoon of Friday, October 8. The irregular-shaped rock was pushed several inches by the Lander's collector arm, which displaced the rock to the left of its original position, leaving it cocked slightly upward. Photographs and other information verified the successful rock push. Photo at left shows the soil sampler's collector head pushing against the rock, named 'Mister Badger' by flight controllers. Photo at right shows the displaced rock and the depression whence it came. Part of the soil displacement was caused by the collector s backhoe. A soil sample will be taken from the site Monday night, October 11. It will then be delivered to Viking s organic chemistry instrument for a series of analyses during the next few weeks. The sample is being sought from beneath a rock because scientists believe that, if there are life forms on Mars, they may seek rocks as shelter from the Sun s intense ultraviolet radiation.

On the effective stress law for rock-on-rock frictional sliding, and fault slip triggered by means of fluid injection

Science.gov (United States)

Rutter, Ernest; Hackston, Abigail

2017-08-01

Fluid injection into rocks is increasingly used for energy extraction and for fluid wastes disposal, and can trigger/induce small- to medium-scale seismicity. Fluctuations in pore fluid pressure may also be associated with natural seismicity. The energy release in anthropogenically induced seismicity is sensitive to amount and pressure of fluid injected, through the way that seismic moment release is related to slipped area, and is strongly affected by the hydraulic conductance of the faulted rock mass. Bearing in mind the scaling issues that apply, fluid injection-driven fault motion can be studied on laboratory-sized samples. Here, we investigate both stable and unstable induced fault slip on pre-cut planar surfaces in Darley Dale and Pennant sandstones, with or without granular gouge. They display contrasting permeabilities, differing by a factor of 105, but mineralogies are broadly comparable. In permeable Darley Dale sandstone, fluid can access the fault plane through the rock matrix and the effective stress law is followed closely. Pore pressure change shifts the whole Mohr circle laterally. In tight Pennant sandstone, fluid only injects into the fault plane itself; stress state in the rock matrix is unaffected. Sudden access by overpressured fluid to the fault plane via hydrofracture causes seismogenic fault slips. This article is part of the themed issue 'Faulting, friction and weakening: from slow to fast motion'.

On the effective stress law for rock-on-rock frictional sliding, and fault slip triggered by means of fluid injection.

Science.gov (United States)

Rutter, Ernest; Hackston, Abigail

2017-09-28

Fluid injection into rocks is increasingly used for energy extraction and for fluid wastes disposal, and can trigger/induce small- to medium-scale seismicity. Fluctuations in pore fluid pressure may also be associated with natural seismicity. The energy release in anthropogenically induced seismicity is sensitive to amount and pressure of fluid injected, through the way that seismic moment release is related to slipped area, and is strongly affected by the hydraulic conductance of the faulted rock mass. Bearing in mind the scaling issues that apply, fluid injection-driven fault motion can be studied on laboratory-sized samples. Here, we investigate both stable and unstable induced fault slip on pre-cut planar surfaces in Darley Dale and Pennant sandstones, with or without granular gouge. They display contrasting permeabilities, differing by a factor of 10 5 , but mineralogies are broadly comparable. In permeable Darley Dale sandstone, fluid can access the fault plane through the rock matrix and the effective stress law is followed closely. Pore pressure change shifts the whole Mohr circle laterally. In tight Pennant sandstone, fluid only injects into the fault plane itself; stress state in the rock matrix is unaffected. Sudden access by overpressured fluid to the fault plane via hydrofracture causes seismogenic fault slips.This article is part of the themed issue 'Faulting, friction and weakening: from slow to fast motion'. © 2017 The Authors.

SU-E-T-556: Monte Carlo Generated Dose Distributions for Orbital Irradiation Using a Single Anterior-Posterior Electron Beam and a Hanging Lens Shield

International Nuclear Information System (INIS)

Duwel, D; Lamba, M; Elson, H; Kumar, N

2015-01-01

Purpose: Various cancers of the eye are successfully treated with radiotherapy utilizing one anterior-posterior (A/P) beam that encompasses the entire content of the orbit. In such cases, a hanging lens shield can be used to spare dose to the radiosensitive lens of the eye to prevent cataracts. Methods: This research focused on Monte Carlo characterization of dose distributions resulting from a single A-P field to the orbit with a hanging shield in place. Monte Carlo codes were developed which calculated dose distributions for various electron radiation energies, hanging lens shield radii, shield heights above the eye, and beam spoiler configurations. Film dosimetry was used to benchmark the coding to ensure it was calculating relative dose accurately. Results: The Monte Carlo dose calculations indicated that lateral and depth dose profiles are insensitive to changes in shield height and electron beam energy. Dose deposition was sensitive to shield radius and beam spoiler composition and height above the eye. Conclusion: The use of a single A/P electron beam to treat cancers of the eye while maintaining adequate lens sparing is feasible. Shield radius should be customized to have the same radius as the patient’s lens. A beam spoiler should be used if it is desired to substantially dose the eye tissues lying posterior to the lens in the shadow of the lens shield. The compromise between lens sparing and dose to diseased tissues surrounding the lens can be modulated by varying the beam spoiler thickness, spoiler material composition, and spoiler height above the eye. The sparing ratio is a metric that can be used to evaluate the compromise between lens sparing and dose to surrounding tissues. The higher the ratio, the more dose received by the tissues immediately posterior to the lens relative to the dose received by the lens

Source rock

Directory of Open Access Journals (Sweden)

Abubakr F. Makky

2014-03-01

Full Text Available West Beni Suef Concession is located at the western part of Beni Suef Basin which is a relatively under-explored basin and lies about 150 km south of Cairo. The major goal of this study is to evaluate the source rock by using different techniques as Rock-Eval pyrolysis, Vitrinite reflectance (%Ro, and well log data of some Cretaceous sequences including Abu Roash (E, F and G members, Kharita and Betty formations. The BasinMod 1D program is used in this study to construct the burial history and calculate the levels of thermal maturity of the Fayoum-1X well based on calibration of measured %Ro and Tmax against calculated %Ro model. The calculated Total Organic Carbon (TOC content from well log data compared with the measured TOC from the Rock-Eval pyrolysis in Fayoum-1X well is shown to match against the shale source rock but gives high values against the limestone source rock. For that, a new model is derived from well log data to calculate accurately the TOC content against the limestone source rock in the study area. The organic matter existing in Abu Roash (F member is fair to excellent and capable of generating a significant amount of hydrocarbons (oil prone produced from (mixed type I/II kerogen. The generation potential of kerogen in Abu Roash (E and G members and Betty formations is ranging from poor to fair, and generating hydrocarbons of oil and gas prone (mixed type II/III kerogen. Eventually, kerogen (type III of Kharita Formation has poor to very good generation potential and mainly produces gas. Thermal maturation of the measured %Ro, calculated %Ro model, Tmax and Production index (PI indicates that Abu Roash (F member exciting in the onset of oil generation, whereas Abu Roash (E and G members, Kharita and Betty formations entered the peak of oil generation.

Phosphoryl transfer is not rate-limiting for the ROCK I-catalyzed kinase reaction.

Science.gov (United States)

Futer, Olga; Saadat, Ahmad R; Doran, John D; Raybuck, Scott A; Pazhanisamy, S

2006-06-27

Rho-associated coiled-coil kinase, ROCK, is implicated in Rho-mediated cell adhesion and smooth muscle contraction. Animal models suggest that the inhibition of ROCK can ameliorate conditions, such as vasospasm, hypertension, and inflammation. As part of our effort to design novel inhibitors of ROCK, we investigated the kinetic mechanism of ROCK I. Steady-state bisubstrate kinetics, inhibition kinetics, isotope partition analysis, viscosity effects, and presteady-state kinetics were used to explore the kinetic mechanism. Plots of reciprocals of initial rates obtained in the presence of nonhydrolyzable ATP analogues and the small molecule inhibitor of ROCK, Y-27632, against the reciprocals of the peptide concentrations yielded parallel lines (uncompetitive pattern). This pattern is indicative of an ordered binding mechanism, with the peptide adding first. The staurosporine analogue K252a, however, gave a noncompetitive pattern. When a pulse of (33)P-gamma-ATP mixed with ROCK was chased with excess unlabeled ATP and peptide, 0.66 enzyme equivalent of (33)P-phosphate was incorporated into the product in the first turnover. The presence of ATPase activity coupled with the isotope partition data is a clear evidence for the existence of a viable [E-ATP] complex in the kinase reaction and implicates a random binding mechanism. The k(cat)/K(m) parameters were fully sensitive to viscosity (viscosity effects of 1.4 +/- 0.2 and 0.9 +/- 0.3 for ATP and peptide 5, respectively), and therefore, the barriers to dissociation of either substrate are higher than the barrier for the phosphoryl transfer step. As a consequence, not all the binding steps are at fast equilibrium. The observation of a burst in presteady-state kinetics (k(b) = 10.2 +/- 2.1 s(-)(1)) and the viscosity effect on k(cat) of 1.3 +/- 0.2 characterize the phosphoryl transfer step to be fast and the release of product and/or the enzyme isomerization step accompanying it as rate-limiting at V(max) conditions. From

Some new developments in the design rules for coastal structures in relation with the new Rock Manual

OpenAIRE

Verhagen, H.J.

2005-01-01

In 1991 CUR in the Netherlands and CIRIA in the UK have published the "manual on the use of rock in coastal engineering", usually referred to as the "Rock Manual". This book of 600 pages gave an overview of the state of the art regarding the design of rock structures along coasts. In 1995 CUR published a adapted version of this book, also containing information on closure works and rock structures along rivers. Although the information in these books is not outdated, there was a general feeli...

Lithology, microstructures, fluid inclusions, and geochemistry of rock salt and of the cap-rock contact in Oakwood Dome, East Texas: significance for nuclear waste storage. Report of investigations No. 120

International Nuclear Information System (INIS)

Dix, O.R.; Jackson, M.P.A.

1982-01-01

Oakwood salt dome in Leon and Freestone Counties, Texas, has a core composed of a diapiric salt stock at a depth of 355 m. A vertical borehole in the center of the salt stock yielded 57.3 m of continuous rock-salt core overlain by 137 m of anhydrite-calcite cap rock. The lower 55.3 m of rock salt exhibits a strong, penetrative schistosity and parallel cleavage dipping at 30 to 40 0 and more than 60 variably dipping layers of disseminated anhydrite. Anhydrite constitutes 1.3 +- 0.7 percent of the rock-salt core. The upper 2 m of rock salt is unfoliated, comprising a lower 1.4-m interval of medium-grained granoblastic rock salt and an upper 0.6-m interval of coarse-grained granoblastic rock salt. An abrupt, cavity-free contact separates rock salt from laminated cap rock consisting of granoblastic-polygonal anhydrite virtually devoid of halite or pore space. Microstructures and concentration gradients of fluid inclusions suggest that the unfoliated rock salt at the crest of the salt stock was once strongly foliated, but that this fabric was destroyed by solid-state recrystallization. Downward movement of brine from the rock-salt - cap-rock contact was apparently accompanied by two recrystallization fronts. Dissolution of halite at the contact released disseminated anhydrite that presumably accumulated as sand on the floor of the dissolution cavity. Renewed rise of the salt stock closed the cavity, and the anhydrite sand was accreted against the base of the cap rock. Much, if not all, of the lamination in the 80 m of anhydrite cap rock may result from cycles of dissolution, recrystallization, and upward movement in the salt stock, followed by accretion of anhydrite residuum as laminae against the base of the cap rock. These processes, which are strongly influenced by fluids, act both to breach waste repositories and to geologically isolate them

Basic rocks in Finland

International Nuclear Information System (INIS)

Piirainen, T.; Gehoer, S.; Iljina, M.; Kaerki, A.; Paakkola, J.; Vuollo, J.

1992-10-01

Basic igneous rocks, containing less than 52% SiO 2 , constitute an important part of the Finnish Archaean and Proterozoic crust. In the Archaean crust exist two units which contain the majority of the basic rocks. The Arcaean basic rocks are metavolcanics and situated in the Greenstone Belts of Eastern Finland. They are divided into two units. The greenstones of the lower one are tholeiites, komatiites and basaltic komatiites. The upper consists of bimodal series of volcanics and the basic rocks of which are Fe-tholeiites, basaltic komatiites and komatiites. Proterozoic basic rocks are divided into seven groups according to their ages. The Proterozoic igneous activity started by the volominous basic magmatism 2.44 Ga ago. During this stage formed the layered intrusions and related dykes in the Northern Finland. 2.2 Ga old basic rocks are situated at the margins of Karelian formations. 2.1 Ga aged Fe-tholeiitic magmatic activity is widespread in Eastern and Northern Finland. The basic rocks of 1.97 Ga age group are met within the Karelian Schist Belts as obducted ophiolite complexes but they occur also as tholeiitic diabase dykes cutting the Karelian schists and Archean basement. The intrusions and the volcanics of the 1.9 Ga old basic igneous activity are mostly encountered around the Granitoid Complex of Central Finland. Subjotnian, 1.6 Ga aged tholeiitic diabases are situated around the Rapakivi massifs of Southern Finland, and postjotnian, 1.2 Ga diabases in Western Finland where they form dykes cutting Svecofennian rocks

Pore-scale analysis of electrical properties in thinly bedded rock using digital rock physics

International Nuclear Information System (INIS)

Sun, Jianmeng; Zhao, Jianpeng; Liu, Xuefeng; Chen, Hui; Jiang, LiMing; Zhang, JinYan

2014-01-01

We investigated the electrical properties of laminated rock consist of macro-porous layers and micro-porous layers based on digital rock technology. Due to the bedding effect and anisotropy, traditional Archie equations cannot well describe the electrical behavior of laminated rock. The RI-Sw curve of laminated rock shows a nonlinear relationship. The RI-Sw curve can be divided into two linear segments with different saturation exponent. Laminated sand-shale sequences and laminated sands of different porosity or grain size will yield macroscopic electrical anisotropy. Numerical simulation and theoretical analysis lead to the conclusion that electrical anisotropy coefficient of laminated rock is a strong function of water saturation. The function curve can be divided into three segments by the turning point. Therefore, the electrical behavior of laminated rock should be considered in oil exploration and development. (paper)

Growth potential of Eucalyptus cypellocarpa as an alternative species for the mid-altitude summer rainfall region of South Africa

CSIR Research Space (South Africa)

Komakech, C

2013-09-01

Full Text Available . There were distinct family and provenance differences for growth at the different sites, with the Hanging Rock provenance generally performing well across all sites. A genotype × environment interaction was present between two sites, as indicated by low Type...

Mechanics of debris flows and rock avalanches: Chapter 43

Science.gov (United States)

Iverson, Richard M.; Fernando, Harindra Joseph

2012-01-01

Debris flows are geophysical phenomena intermediate in character between rock avalanches and flash floods. They commonly originate as water-laden landslides on steep slopes and transform into liquefied masses of fragmented rock, muddy water, and entrained organic matter that disgorge from canyons onto valley floors. Typically including 50%–70% solid grains by volume, attaining speeds >10 m/s, and ranging in size up to ∼109 m3, debris flows can denude mountainsides, inundate floodplains, and devastate people and property (Figure 43.1). Notable recent debris-flow disasters resulted in more than 20,000 fatalities in Armero, Colombia, in 1985 and in Vargas state, Venezuela, in 1999.

Geotechnical site assessment for underground radioactive waste disposal in rock

International Nuclear Information System (INIS)

Hudson, J.A.

1986-05-01

This report contains a state-of-the-art review of the geotechnical assessment of Land 3 and Land 4 repository sites (at 100 - 300 m depth in rock) for intermediate level radioactive waste disposal. The principles established are also valid for the disposal of low and high level waste in rock. The text summarizes the results of 21 DoE research contract reports, firstly 'in series' by providing a technical review of each report and then 'in parallel' by considering the current state of knowledge in the context of the subjects in an interaction matrix framework. 1214 references are cited. It is concluded that four further research projects are required for site assessment procedures to be developed or confirmed. These are coupled modelling, mechanical properties, water flow and establishment of 2 phase site assessment procedures. (author)

Exploration of cystalline rocks for nuclear waste repositories: Some strategies for area characterization

International Nuclear Information System (INIS)

Trask, N.J.; Roseboom, E.H.; Watts, R.D.; Bedinger, M.S.

1991-01-01

A general strategy for the exploration of crystalline rock massed in the eastern United States for the identification of potential sites for high-level radioactive waste repositories has been generated by consideration of the Department of Energy (DOE) Siting Guidelines, available information on these crystalline rocks, and the capabilities and limitations of various exploration methods. The DOE has recently screened over 200 crystalline rock massed in 17 states by means of literature surveys and has recommended 12 rock masses for more intensive investigation including field investigations. The suggested strategy applies to the next stage of screen where the objective is to identify those potential sites that merit detailed site characterization including an exploratory shaft and underground study. This document discusses strategies for reconnaissance and field investigations, including the early phases of drilling, to provide geoscience information on the areas under construction. A complete Area Characterization Plan, to be developed by DOE with involvement of the states within which the areas to be studied are located, will outline all of the investigations to be carried out in the area phase including their cost and scheduling. Here, we provide input for the Area Characterization Plan by discussing what we believe to be the most important issues that need to be addressed in this phase and suggesting methods for their resolution. This report is not intended as a complete outline of area phase geoscience investigations, however. 79 refs., 4 figs

Strains and stresses in the rock around and unlined hot water cavern

Science.gov (United States)

Rehbinder, Göran

1984-07-01

Hot water stored in an unlined rock cavern is an efficient energy storage. A research program has been carried out with a test plant at the city of Avesta, Sweden. The plant consists of a rock cavern, the volume of which is 15000 m3, which serves as an energy buffer in the district heating system of the city. The water is heated from a garbage incinerator located close to the cavern. During the first test period the temperature of the stored water has varied between 40°C and 95°C. The heating of the rock causes strains and stresses in the rock. The measurements show that the state in the rock does mainly respond to the average temperature and not to the fluctuations. The maximum thermal stress is 9 MPa occurring at the wall of the cavern. The heave of the ground is less than 5 mm. The development of stress and strain will continue after the first test period since thermal equilibrium was not reached during this period.

Formation and hematopoietic differentiation of human embryoid bodies by suspension and hanging drop cultures.

Science.gov (United States)

Cerdan, Chantal; Hong, Seok Ho; Bhatia, Mickie

2007-10-01

The in vitro aggregation of human embryonic stem cells (hESCs) into clusters termed embryoid bodies (EBs) allows for the spontaneous differentiation of cells representing endoderm, mesoderm, and ectoderm lineages. This stochastic process results however, in the generation of low numbers of differentiated cells, and can be enhanced to some extent by the addition of exogenous growth factors or overexpression of regulatory genes. In the authors' laboratory, the use of hematopoietic cytokines in combination with the mesoderm inducer bone morphogenetic protein-4 (BMP-4) was able to generate up to 90% of CD45(+) hematopoietic cells with colony-forming unit (CFU) activity. This unit describes two protocols that have been successfully applied in the authors' laboratory for the generation of EBs in (1) suspension and (2) hanging drop (HD) cultures from enzymatically digested clumps of undifferentiated hESC colonies.

Internally Pressurized Spherical and Cylindrical Cavities in Rock Salt

DEFF Research Database (Denmark)

Krenk, Steen

1978-01-01

-linear zone and the volume reduction. Results are given for cavities in rock salt, and a comparison with measured stress concentrations is used to support the assumption of a hydrostatic stress state in undisturbed salt formations. Finally a method to estimate convergence due to creep is outlined....

Branchipodopsis species — specialists of ephemeral rock pools ...

African Journals Online (AJOL)

Such rock pools were studied in the Drakensberg region, in the eastern Free State and in south-eastern Botswana. Common features ... While short-range dispersal of floating eggs by overflows is common, long-range dispersal (e.g. by wind) seems to be rare and to be restricted to shallow pools with little vegetation. Limited ...

Research into basic rocks types

International Nuclear Information System (INIS)

1993-06-01

Teollisuuden Voima Oy (TVO) has carried out research into basic rock types in Finland. The research programme has been implemented in parallel with the preliminary site investigations for radioactive waste disposal in 1991-1993. The program contained two main objectives: firstly, to study the properties of the basic rock types and compare those with the other rock types under the investigation; secondly, to carry out an inventory of rock formations consisting of basic rock types and suitable in question for final disposal. A study of environmental factors important to know regarding the final disposal was made of formations identified. In total 159 formations exceeding the size of 4 km 2 were identified in the inventory. Of these formations 97 were intrusive igneous rock types and 62 originally extrusive volcanic rock types. Deposits consisting of ore minerals, industrial minerals or building stones related to these formations were studied. Environmental factors like natural resources, protected areas or potential for restrictions in land use were also studied

Evaluation of Rock Bolt Support for Polish Hard Rock Mines

Science.gov (United States)

Skrzypkowski, Krzysztof

2018-03-01

The article presents different types of rock bolt support used in Polish ore mining. Individual point resin and expansion rock bolt support were characterized. The roof classes for zinc and lead and copper ore mines were presented. Furthermore, in the article laboratory tests of point resin rock bolt support in a geometric scale of 1:1 with minimal fixing length of 0.6 m were made. Static testing of point resin rock bolt support were carried out on a laboratory test facility of Department of Underground Mining which simulate mine conditions for Polish ore and hard coal mining. Laboratory tests of point resin bolts were carried out, especially for the ZGH Bolesław, zinc and lead "Olkusz - Pomorzany" mine. The primary aim of the research was to check whether at the anchoring point length of 0.6 m by means of one and a half resin cartridge, the type bolt "Olkusz - 20A" is able to overcome the load.The second purpose of the study was to obtain load - displacement characteristic with determination of the elastic and plastic range of the bolt. For the best simulation of mine conditions the station steel cylinders with an external diameter of 0.1 m and a length of 0.6 m with a core of rock from the roof of the underground excavations were used.

Implanted of Pb-Pb methodology in whole rock: examples of use in Carajas Mineral Province, Para State

International Nuclear Information System (INIS)

Rodrigues, Elizabeth Maria Soares.

1992-01-01

This work presents the first data obtained by Pb-Pb systematics in whole rock and separated minerals. The Pb isotopic compositions of samples were determined by mass spectrometry. The average analytical errors of the ratios 206 Pb/ 204 Pb, 207 Pb/ 204 Pb and 208 Pb/ 209 Pb were 0.10%, 0.12% and 0.15%, respectively. The age calculation in the 207 Pb/ 204 Pb x 206 Pb/ 204 Pb diagram was obtained by York (1969) and Ludwig (1900). In order to verify the efficiency of the implanted methodology, 5 rocks from of the Carajas Mineral Province and Sao Felix do Xingu Region were dated. The Velho Guilherme granite, intrusive into the granite-greenstone terrains of Tucuma Region (PA), provided a Pb-Pb crystallization age (11 WR,2 FELD) of 1874 ± 15 Ma with MSWD = 1.53 and μ 1 = 8.9 ± 0.07 (single stage). The Granulitic rocks of Pium complex (Catete area), located at the SW of Serra dos Carajas, provided a Pb-Pb age of 3044 ± 64 Ma with MSWD = 28.72 and μ 1 = 9.2 ± .58. In the Rio Maria Region, Mata Surrao monzogranite which cross cut the gneiss basement and associated to the greenstone belts, defined a crystallization Pb-Pb (8 WR) age of 2876 ± 10 Ma with MSWD = 3.71 and μ 1 = 8.2 ± 0.11. In the same region, the Metabasalts of the Identidade greenstone belt, (Andorinhas supergroup), showed a Pb-Pb age in whole rock (7 samples) of 3400 ± 109 Ma with MSWD = 7.97 and μ 1 = 9.6 ± 1.44. Five whole rock samples from metadacites, located in the central part of the Identidade greenstone, provided a crystallization age of 2944 ± 88 Ma with MSWD 31.52 and μ 1 = 8.2 ± .70. The results obtained in this work emphasize the high potentiality of the Pb-Pb method of dating to obtain crystallization ages of Precambrian rocks. (author). 69 refs., 23 figs., 12 tabs

Rationale for geological isolation of high-level radioactive waste, and assessment of the suitability of crystalline rocks

International Nuclear Information System (INIS)

Smedes, H.W.

1980-01-01

This report summarizes the disposal objective to be met and the requisite geotechnical criteria to meet that objective; evaluates our present ability to determine whether certain criteria can be met and to predict whether they will continue to be met; discusses the consequences of failure to meet certain criteria; assesses what is known about how crystalline rocks meet those criteria; lists important gaps in our knowledge that presently preclude final assessment of suitability; and suggests priority research to fill those gaps. The report presents an elaboration of the above-stated behavior and suitability of crystalline rocks, and a rationale of site-selection in support of the recommended prompt and intensive study of granite and other crystalline rocks as potentially highly suitable candidate media for radioactive waste disposal. An overview is presented on what the rocks are, where they are, and what the critical attributes are of various crystalline-rock terranes in the conterminous United States. This is intended to provide a basis to aid in selecting, first regions, and then sites within those regions, as candidate repository sites

Geochronological studies by Rb/Sr method in rocks of the Jundiai block and surroundings. [Ampario group

Energy Technology Data Exchange (ETDEWEB)

Wernick, E [Faculdade de Filosofia Ciencias e Letras de Rio Claro; Oliveira, M A.F. de; Kawashita, K; Cordani, U G [Sao Paulo Univ. (Brazil). Inst. de Geociencias; Delhal, J [Musee Royal de l' Afrique Centrale, Belgica

1976-01-01

Field and petrological data, as well as radiometric results performed in granulitic, gneissic, migmatitic, and granitic rocks from the 'Jundiai tectonic block' (States of Sao Paulo and Minas Gerais), show for that region the existence of two superposed orogeneses. To the older, of transamazonian age whole rock Rb-Sr isochron 2,010 m.y. Rb/sup 87//Sr/sup 86/ initial = 0.702), belongs the Amparo Group, composed of gneisses, migmatites, and granulites, with intercalation of quartzites, schists and calc-silicate rocks. To the younger, of brazilian age whole rock Rb-Sr isochron 690 m.y. (Sr/sup 87//Sr/sup 86/ initial = 0.702), are related the feldspathization and migmatization of the Amparo Group, as well as the intrusion of granitic bodies. Possibly, also the metasediments around Jacarei belong to the brazilian cycle. This pattern of geologic evolution is similar to that observed for the Serra dos Orgaos region (States of Rio de Janeiro and Minas Gerais).

Studying electron transfer through alkanethiol self-assembled monolayers on a hanging mercury drop electrode using potentiometric measurements.

Science.gov (United States)

Cohen-Atiya, Meirav; Mandler, Daniel

2006-10-14

A new approach based on measuring the change of the open-circuit potential (OCP) of a hanging mercury drop electrode (HMDE), modified with alkanethiols of different chain length conducted in a solution containing a mixture of Ru(NH3)6(2+) and Ru(NH3)6(3+) is used for studying electron transfer across the monolayer. Following the time dependence of the OCP allowed the extraction of the kinetic parameters, such as the charge transfer resistance (R(ct)) and the electron transfer rate constant (k(et)), for different alkanethiol monolayers. An electron tunneling coefficient, beta, of 0.9 A(-1) was calculated for the monolayers on Hg.

Klassiõpetaja peab särama / Ly Melesk, Kairis Kontus, Leida Talts, Viia Hang...[jt.] ; küsitles Anu Mõttus

Index Scriptorium Estoniae

2007-01-01

Vestlusringis on Tallinna Kuristiku Gümnaasiumi klassiõpetajad Viia Hang ja Ly Melesk, Tallinna Ülikooli 5. kursuse üliõpilane ja Tallinna Lepistiku Lasteaed-Algkooli õpetaja Kairis Kontus, Tallinna Ülikooli algõpetuse õppetooli juhataja Leida Talts ning algõpetuse õppetooli pedagoogika ja algõpetuse metoodika õppejõud Mare Müürsepp. Kui hästi on Tallinna Ülikool ja tema eelkäijad suutnud algklassiõpetajaid ette valmistada ja mis neil igapäevatöös toime tulla aitab

Soil erosion and effluent particle size distribution under different initial conditions and rock fragment coverage

Science.gov (United States)

Jomaa, S.; Barry, D. A.; Brovelli, A.; Heng, B. C. P.; Sander, G. C.; Parlange, J.-Y.

2012-04-01

It is well known that the presence of rock fragments on the soil surface and the soil's initial characteristics (moisture content, surface roughness, bulk density, etc.) are key factors influencing soil erosion dynamics and sediment delivery. In addition, the interaction of these factors increases the complexity of soil erosion patterns and makes predictions more difficult. The aim of this study was (i) to investigate the effect of soil initial conditions and rock fragment coverage on soil erosion yields and effluent particle size distribution and (ii) to evaluate to what extent the rock fragment coverage controls this relationship. Three laboratory flume experiments with constant precipitation rate of 74 mm/h on a loamy soil parcel with a 2% slope were performed. Experiments with duration of 2 h were conducted using the 6-m × 2-m EPFL erosion flume. During each experiment two conditions were considered, a bare soil and a rock fragment-protected (with 40% coverage) soil. The initial soil surface state was varied between the three experiments, from a freshly re-ploughed and almost dry condition to a compacted soil with a well-developed shield layer and high moisture content. Experiments were designed so that rain splash was the primary driver of soil erosion. Results showed that the amount of eroded mass was highly controlled by the initial soil conditions and whether the steady-state equilibrium was un-, partially- or fully- developed during the previous event. Additionally, results revealed that sediment yields and particle size composition in the initial part of an erosion event are more sensitive to the erosion history than the long-time behaviour. This latter appears to be mainly controlled by rainfall intensity. If steady-state was achieved for a previous event, then the next event consistently produced concentrations for each size class that peaked rapidly, and then declined gradually to steady-state equilibrium. If steady state was not obtained, then

Geotechnical assessment and instrumentation needs for nuclear waste isolation in crystalline and argillaceous rocks

International Nuclear Information System (INIS)

1979-01-01

To evaluate the state-of-the-art, research needs, and research priorities related to waste disposal in largely impermeable rocks, scientists and engineers working on geologic aspects of nuclear waste disposal were brought together. This report and recommendations are the proceedings from that symposium. Three panels were organized on rock properties, fracture hydrology, and geochemistry. Panel discussions and recommendations are presented

Igneous Rocks

Science.gov (United States)

Doe, Bruce R.

“Igneous Rocks was written for undergraduate geology majors who have had a year of college-level chemistry and a course in mineralogy … and for beginning graduate students. Geologists working in industry, government, or academia should find this text useful as a guide to the technical literature up to 1981 and as an overview of topics with which they have not worked but which may have unanticipated pertinence to their own projects.” So starts the preface to this textbook.As one who works part time in research on igneous rocks, especially as they relate to mineral deposits, I have been looking for such a book with this avowed purpose in a field that has a choking richness of evolving terminology and a bewildering volume of interdisciplinary literature. In addition to the standard topics of igneous petrology, the book contains a chapter on the role of igneous activity in the genesis of mineral deposits, its value to geothermal energy, and the potential of igneous rocks as an environment for nuclear waste disposal. These topics are presented rather apologetically in the preface, but the author is to be applauded for including this chapter. The apology shows just how new these interests are to petrology. Recognition is finally coming that, for example, mineral deposits are not “sports of nature,” a view held even by many economic geologists as recently as the early 1960's; instead they are perfectly ordinary geochemical features formed by perfectly ordinary geologic processes. In fact, the mineral deposits and their attendant alteration zones probably have as much to tell us about igneous rocks as the igneous rocks have to tell us about mineral deposits.

Radioactivities (dose rates) of rocks in Japan

International Nuclear Information System (INIS)

Matsuda, Hideharu; Minato, Susumu

1995-01-01

The radioactive distribution (radiation doses) of major rocks in Japan was monitored to clarify the factors influencing terrestrial gamma-ray absorbed dose rates. The rock samples were reduced to powder and analyzed by well-type NaI(Tl) scintillation detector and pulse height analyzer. Terrestrial gamma-ray dose rates were estimated in terms of gamma radiation dose rate 1 m above the ground. The radioactivity concentration was highest in acidic rock which contains much SiO 2 among igneous rock, followed by neutral rock, basic rock, and ultrabasic rock. The radioactive concentration was 30-40% lower in acidic and clastic rocks than those of the world average concentration. Higher radioactive concentration was observed in soils than the parent rocks of sedimentary rock and metamorphic rock. The gamma radiation dose rate was in proportion to the radioactive concentration of the rocks. To clarify the radioactive effect in the change course of rocks into soils, comparative measurement of outcrop and soil radioactive concentrations is important. (S.Y.)

Influence of Toe-Hang vs. Face-Balanced Putter Design on Golfer Applied Kinetics

Directory of Open Access Journals (Sweden)

Sasho MacKenzie

2018-02-01

Full Text Available The influence of the location of the center of mass (cm of the putter head, relative to the shaft, on golfer applied kinetics at the grip was investigated. Participants made 12 attempts at a straight up-hill (2.2° slope 8 ft putt with half of the attempts executed using a PING Anser 4 toe-hang putter (TH and half with an Anser 5 face-balanced putter (FB. The net torque applied by the golfer, acting about the long axis of the shaft, was significantly greater in magnitude with the TH putter in comparison to the FB putter. The TH putter was also associated with a higher angular velocity about the shaft and a more open face at impact. These findings may have important implications for fitting the style of putter to a particular stroke or individual golfer as golfer applied kinetics would be strongly associated with the ‘feel’ of a putter.

Rock critics as 'Mouldy Modernists'

Directory of Open Access Journals (Sweden)

Becky Shepherd

2011-08-01

Full Text Available Contemporary rock criticism appears to be firmly tied to the past. The specialist music press valorise rock music of the 1960s and 1970s, and new emerging artists are championed for their ‘retro’ sounding music by journalists who compare the sound of these new artists with those included in the established ‘canon’ of rock music. This article examines the narrative tropes of authenticity and nostalgia that frame the retrospective focus of this contemporary rock writing, and most significantly, the maintenance of the rock canon within contemporary popular culture. The article concludes by suggesting that while contemporary rock criticism is predominately characterised by nostalgia, this nostalgia is not simply a passive romanticism of the past. Rather, this nostalgia fuels a process of active recontextualisation within contemporary popular culture.

Bioremediation in fractured rock: 2. Mobilization of chloroethene compounds from the rock matrix

Science.gov (United States)

Shapiro, Allen M.; Tiedeman, Claire; Imbrigiotta, Thomas; Goode, Daniel J.; Hsieh, Paul A.; Lacombe, Pierre; DeFlaun, Mary F.; Drew, Scott R.; Curtis, Gary P.

2018-01-01

A mass balance is formulated to evaluate the mobilization of chlorinated ethene compounds (CE) from the rock matrix of a fractured mudstone aquifer under pre- and postbioremediation conditions. The analysis relies on a sparse number of monitoring locations and is constrained by a detailed description of the groundwater flow regime. Groundwater flow modeling developed under the site characterization identified groundwater fluxes to formulate the CE mass balance in the rock volume exposed to the injected remediation amendments. Differences in the CE fluxes into and out of the rock volume identify the total CE mobilized from diffusion, desorption, and nonaqueous phase liquid dissolution under pre- and postinjection conditions. The initial CE mass in the rock matrix prior to remediation is estimated using analyses of CE in rock core. The CE mass mobilized per year under preinjection conditions is small relative to the total CE mass in the rock, indicating that current pump-and-treat and natural attenuation conditions are likely to require hundreds of years to achieve groundwater concentrations that meet regulatory guidelines. The postinjection CE mobilization rate increased by approximately an order of magnitude over the 5 years of monitoring after the amendment injection. This rate is likely to decrease and additional remediation applications over several decades would still be needed to reduce CE mass in the rock matrix to levels where groundwater concentrations in fractures achieve regulatory standards.

Regulation of ROCK Activity in Cancer

DEFF Research Database (Denmark)

Morgan-Fisher, Marie; Wewer, Ulla M; Yoneda, Atsuko

2013-01-01

, these findings demonstrate additional modes to regulate ROCK activity. This review describes the molecular mechanisms of ROCK activity regulation in cancer, with emphasis on ROCK isoform-specific regulation and interaction partners, and discusses the potential of ROCKs as therapeutic targets in cancer.......Cancer-associated changes in cellular behavior, such as modified cell-cell contact, increased migratory potential, and generation of cellular force, all require alteration of the cytoskeleton. Two homologous mammalian serine/threonine kinases, Rho-associated protein kinases (ROCK I and II), are key...... regulators of the actin cytoskeleton acting downstream of the small GTPase Rho. ROCK is associated with cancer progression, and ROCK protein expression is elevated in several types of cancer. ROCKs exist in a closed, inactive conformation under quiescent conditions, which is changed to an open, active...

Commercial potential of natural gas storage in lined rock caverns (LRC)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-11-01

The geologic conditions in many regions of the United States will not permit the development of economical high-deliverability gas storage in salt caverns. These regions include the entire Eastern Seaboard; several northern states, notably Minnesota and Wisconsin; many of the Rocky Mountain States; and most of the Pacific Northwest. In late 1997, the United States Department of Energy (USDOE) Federal Energy Technology Center engaged Sofregaz US to investigate the commercialization potential of natural gas storage in Lined Rock Caverns (LRC). Sofregaz US teamed with Gaz de France and Sydkraft, who had formed a consortium, called LRC, to perform the study for the USDOE. Underground storage of natural gas is generally achieved in depleted oil and gas fields, aquifers, and solution-mined salt caverns. These storage technologies require specific geologic conditions. Unlined rock caverns have been used for decades to store hydrocarbons - mostly liquids such as crude oil, butane, and propane. The maximum operating pressure in unlined rock caverns is limited, since the host rock is never entirely impervious. The LRC technology allows a significant increase in the maximum operating pressure over the unlined storage cavern concept, since the gas in storage is completely contained with an impervious liner. The LRC technology has been under development in Sweden by Sydkraft since 1987. The development process has included extensive technical studies, laboratory testing, field tests, and most recently includes a storage facility being constructed in southern Sweden (Skallen). The LRC development effort has shown that the concept is technically and economically viable. The Skallen storage facility will have a rock cover of 115 meters (375 feet), a storage volume of 40,000 cubic meters (250,000 petroleum barrels), and a maximum operating pressure of 20 MPa (2,900 psi). There is a potential for commercialization of the LRC technology in the United States. Two regions were studied

Strategy for future laboratory rock mechanics programs

International Nuclear Information System (INIS)

Butcher, B.M.; Jones, A.K.

1985-01-01

A strategy for future experimental rock mechanics laboratory programs at Sandia National Laboratories is described. This strategy is motivated by the need for long range planning of rock mechanics programs addressing the stability of complex underground structures, changes in in situ stress states during resource recovery and underground explosion technology. It is based on: (1) recent advances in underground structure stability analysis which make three-dimensional calculations feasible, and (2) new developments in load path control of laboratory stress-strain tests which permit duplication of stress and strain histories in critical parts of a structure, as determined by numerical analysis. The major constraint in the strategy is the assumption that there are no in situ joint features or sample size effects which might prevent simulation of in situ response in the laboratory. 3 refs., 5 figs

Forms of iron in soils on basement complex rocks of Kaduna state in ...

African Journals Online (AJOL)

The forms of iron extracted by different methods were studied in soils developed on four basement complex rocks within Northern Guinea Savanna of Nigeria namely: migmatite gneisses, older granite, quartzites and mica schists. The study shows that forms of iron generally decreased in the order of total elemental iron ...

Comparative study of destructive and non-destructive methods in the activation analysis of rocks

International Nuclear Information System (INIS)

Vasconcellos, M.B.A.

1978-01-01

A comparative study between non-destructive thermal neutron activation analysis and activation analysis with radiochemical group separation is made Both methods are applied to the determination of trace elements minor and major elements in rocks. The treatment of the rocks, with special reference to the problems related to grinding and contamination by foreign elements is described. The choice of standards for multielement trace activation analysis is discussed. Two types of computer programs for the evalution of data obtained through Ge-li detector counting are used. All the phases of the destructive and non destructive analysis are described. In the destructive analysis, an adaptation of the group separation scheme developed by Morrison et al for the activation analysis of geological samples is made. The changes introduced make the radiochemical separation simpler and more rapid. Both destructive and non destructive methods are tested by means of the analysis of the United States Geological Survey standard rock AGV-1, which has been analysed by many authors. The same procedure is then applied to some alcaline rocks taken from the apatite mine of Jacupiranga, in the State of Sao Paulo, Brazil. The knowledge of the trace element concentration in these rocks is important for geochemical studies. A detailed study of the possible interferences encountered in the neutron activation analysis of these rocks is made, considering the interferences due to major activities, and to the proximity of the several gamma ray energies of the radioisotopes produced. Finally, the comparative study between the two methods is presented, using statistical tests for the quantitative evalution of results. (Author) [pt

Investigation of Non-Linear Dynamics of the Rock Massive,Using Seismological Catalogue data and Induction Electromagnetic Monitoring Data in a Rock Burst Mine.

Science.gov (United States)

Hachay, O. A.; Khachay, O. Y.; Klimko, V. K.; Shipeev, O. V.

2012-04-01

Geological medium is an open dynamical system, which is influenced on different scales by natural and man-made impacts, which change the medium state and lead as a result to a complicated many ranked hierarchic evolution. That is the subject of geo synergetics. Paradigm of physical mesomechanics, which was advanced by academician Panin V.E. and his scientific school, which includes the synergetic approach is a constructive method for research and changing the state of heterogenic materials [1]. That result had been obtained on specimens of different materials. In our results of research of no stationary geological medium in a frame of natural experiments in real rock massifs, which are under high man-made influence it was shown, that the state dynamics can be revealed with use synergetics in hierarchic medium. Active and passive geophysical monitoring plays a very important role for research of the state of dynamical geological systems. It can be achieved by use electromagnetic and seismic fields. Our experience of that research showed the changing of the system state reveals on the space scales and times in the parameters, which are linked with the peculiarities of the medium of the second or higher ranks [2-5]. Results of seismological and electromagnetic information showed the mutual additional information on different space-time levels of rock massive state, which are energetic influenced by explosions, used in mining technology. It is revealed a change of nonlinearity degree in time of the massive state by active influence on it. The description of massive movement in a frame of linear dynamical system does not satisfy the practical situation. The received results are of great significance because for the first time we could find the coincidences with the mathematical theory of open systems and experimental natural results with very complicated structure. On that base we developed a new processing method for the seismological information which can be used in

Rock stress measurements in the Grimsel Underground Rock Laboratory and their geological interpretation

International Nuclear Information System (INIS)

Braeuer, V.; Heusermann, S.; Pahl, A.

1989-01-01

Rock stress is being studied as part of the Swiss-German cooperation between the National Cooperative for the Storage of Radioactive Waste (NAGRA), the Research Centre for Environmental Sciences (GSF), and the Federal Institute for Geosciences and Natural Resources (BGR) in the Grimsel Rock Laboratory in Switzerland. Several methods and various equipment for measuring rock stress have been developed and tested in an approximately 200-m borehole drilled from a gallery at a depth of 450 m. The measurements were made continually during overcoring; the data were recorded and processed in a computer located downhole or outside the borehole. The results of the overcoring tests and of frac tests indicate a principle horizontal stress of 25-40 MPa, directed mainly NW-SE. Detailed geological mapping shows relationships between stress and rock structure. A zone of nearly unfractured rock exhibits an increase in stress and a change in stress direction. (orig.)

Rock in Rio: forever young

Directory of Open Access Journals (Sweden)

Ricardo Ferreira Freitas

2014-12-01

Full Text Available The purpose of this article is to discuss the role of Rock in Rio: The Musical, as herald of megafestival Rock in Rio. Driven by the success that musicals have reached in Brazil, we believe that the design of this spectacle of music, dance and staging renews the brand of the rock festival, once it adds the force of young and healthy bodies to its concept. Moreover, the musical provides Rock in Rio with some distance from the controversal trilogy of sex, drugs and rock and roll, a strong mark of past festivals around the world. Thus, the musical expands the possibilities of growth for the brand.

Challenging the Southern Boundary of Active Rock Glaciers in West Greenland

Science.gov (United States)

Langley, K.; Abermann, J.

2017-12-01

Rock glaciers are permafrost features abundant in mountainous environments and are characterized as `steadily creeping perennially frozen and ice-rich debris on non-glacierised mountain slopes'. Previous studies investigated both the climatic significance and the dynamics of rock glaciers in Greenland, however, there do not exist studies as far south as the Godthåbsfjord area. We recently found evidence of a active rock glacier near Nuuk, around 250 km further south than the previously suggested southern active limit. It shows no signs of pioneer vegetation, which supports its likely dynamic activity. The rock glacier covers an area of ca. 1 km2and its lowest point is at an elevation of about 250 m a.s.l. Here we present the results of a two year field campaign designed to (I) confirm or reject active rock glacier occurrence in the Godthåbsfjord area with innovative methods, (II) study their dynamic regime and (III) investigate the climatic boundary conditions necessary for active rock glacier occurrence in the Sub-Arctic. We use a number of methods to determine the state of the rock glacier. Movement of the landform is assessed using repeat GPS surveying of marked stones and feature tracking based on ortho-photos and DEMs from repeat UAV deployments. Bottom temperature of snow cover (BTS) measurements give an independent first-order estimate of permafrost occurrence. An air temperature sensor deployed near the snout and recording hourly gives a first order estimate of the temperature gradients between Nuuk and the rock glacier, allowing us to assess the climatic boundary conditions required for rock glacier occurrence. BTS measurements show a clear drop in temperatures over the rock glacier compared to the surrounding areas suggesting an active landform with a well demarcated thermal regime. We will assess this independently with the repeat GPS and UAV surveys and will thus be able to confirm or reject the hypothesis of activity by the end of summer 2017.

Hydrogeomechanics for rock engineering: coupling subsurface hydrogeomechanical assessement and hydrogeotechnical mapping on fracturated rock masses

OpenAIRE

Meirinhos, João Miguel de Freitas

2015-01-01

The present work aims to achieve and further develop a hydrogeomechanical approach in Caldas da Cavaca hydromineral system rock mass (Aguiar da Beira, NW Portugal), and contribute to a better understanding of the hydrogeological conceptual site model. A collection of several data, namely geology, hydrogeology, rock and soil geotechnics, borehole hydraulics and hydrogeomechanics, was retrieved from three rock slopes (Lagoa, Amores and Cancela). To accomplish a comprehensive analysis and rock e...

Study on natural radioactive elements in soil and rock samples around Mandya district, India

International Nuclear Information System (INIS)

Shivakumara, B.C.; Paramesh, L.; Shashikumar, T.S.; Chandrashekara, M.S.

2012-01-01

The soil is a complex mixture of different compounds and rocks. In the natural environment, it is an important source of exposure to radiation due to naturally occurring, gamma emitting radionuclides which include 226 Ra, 232 Th and 40 K present in the soil. The study of distribution of these radionuclides in soil and rock is of great importance for radiation protection and measurements. The activity concentrations of 226 Ra, 232 Th, and 40 K in soil and rock samples collected in Mandya District, Karnataka state, India have been measured by gamma ray spectrometry. The average activity concentrations of 226 Ra, 232 Th, and 40 K (Bq/kg) are found to be 40.2, 62.3, and 317.5 Bq/kg, respectively, in soil samples and 30.5, 34.4, and 700.2 Bq/kg, respectively, in rock samples. The concentrations of radionuclides in soil samples are found to higher than in rock samples. The concentrations of radionuclides in soil and rock samples in the study area are slightly higher than Indian average and world average values. (author)

Asymmetric step-like characteristics in a tilted rocking ratchet potential

International Nuclear Information System (INIS)

Lee, A. Khangjune; Lee, Jong-Rim; Lee, K.H.

2012-01-01

The overdamped Langevin dynamics has been employed to study the directional transport of particles driven in a tilted rocking ratchet potential. The system subjected to a constant direct force undergoes an asymmetrical dynamic transition from a static state to a sliding state at two different critical forces that are consistent with the predicted values. When an additional alternating force is applied to the system, the time-averaged velocity shows several steps of equal height as the direct force increases. These steps are similar to the Shapiro steps in an rf-driven Josephson junction, and appear whenever the system's natural frequency given by the direct force matches an integer multiple of the applied frequency. When the alternating force exceeds a certain critical value which can be also estimated for a slow rocking, a directional motion known as the rectification effect occurs even at zero direct force.

Underground Research Laboratories for Crystalline Rock and Sedimentary Rock in Japan

Energy Technology Data Exchange (ETDEWEB)

Shigeta, N.; Takeda, S.; Matsui, H.; Yamasaki, S.

2003-02-27

The Japan Nuclear Cycle Development Institute (JNC) has started two off-site (generic) underground research laboratory (URL) projects, one for crystalline rock as a fractured media and the other for sedimentary rock as a porous media. This paper introduces an overview and current status of these projects.

Regulation of ROCK Activity in Cancer

Science.gov (United States)

Morgan-Fisher, Marie; Wewer, Ulla M.

2013-01-01

Cancer-associated changes in cellular behavior, such as modified cell-cell contact, increased migratory potential, and generation of cellular force, all require alteration of the cytoskeleton. Two homologous mammalian serine/threonine kinases, Rho-associated protein kinases (ROCK I and II), are key regulators of the actin cytoskeleton acting downstream of the small GTPase Rho. ROCK is associated with cancer progression, and ROCK protein expression is elevated in several types of cancer. ROCKs exist in a closed, inactive conformation under quiescent conditions, which is changed to an open, active conformation by the direct binding of guanosine triphosphate (GTP)–loaded Rho. In recent years, a number of ROCK isoform-specific binding partners have been found to modulate the kinase activity through direct interactions with the catalytic domain or via altered cellular localization of the kinases. Thus, these findings demonstrate additional modes to regulate ROCK activity. This review describes the molecular mechanisms of ROCK activity regulation in cancer, with emphasis on ROCK isoform-specific regulation and interaction partners, and discusses the potential of ROCKs as therapeutic targets in cancer. PMID:23204112

Bioremediation in Fractured Rock: 2. Mobilization of Chloroethene Compounds from the Rock Matrix.

Science.gov (United States)

Shapiro, Allen M; Tiedeman, Claire R; Imbrigiotta, Thomas E; Goode, Daniel J; Hsieh, Paul A; Lacombe, Pierre J; DeFlaun, Mary F; Drew, Scott R; Curtis, Gary P

2018-03-01

A mass balance is formulated to evaluate the mobilization of chlorinated ethene compounds (CE) from the rock matrix of a fractured mudstone aquifer under pre- and postbioremediation conditions. The analysis relies on a sparse number of monitoring locations and is constrained by a detailed description of the groundwater flow regime. Groundwater flow modeling developed under the site characterization identified groundwater fluxes to formulate the CE mass balance in the rock volume exposed to the injected remediation amendments. Differences in the CE fluxes into and out of the rock volume identify the total CE mobilized from diffusion, desorption, and nonaqueous phase liquid dissolution under pre- and postinjection conditions. The initial CE mass in the rock matrix prior to remediation is estimated using analyses of CE in rock core. The CE mass mobilized per year under preinjection conditions is small relative to the total CE mass in the rock, indicating that current pump-and-treat and natural attenuation conditions are likely to require hundreds of years to achieve groundwater concentrations that meet regulatory guidelines. The postinjection CE mobilization rate increased by approximately an order of magnitude over the 5 years of monitoring after the amendment injection. This rate is likely to decrease and additional remediation applications over several decades would still be needed to reduce CE mass in the rock matrix to levels where groundwater concentrations in fractures achieve regulatory standards. © 2017, National Ground Water Association.

Eos Chaos Rocks

Science.gov (United States)

2006-01-01

11 January 2006 This Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC) image shows light-toned, layered rock outcrops in Eos Chaos, located near the east end of the Valles Marineris trough system. The outcrops occur in the form of a distinct, circular butte (upper half of image) and a high slope (lower half of image). The rocks might be sedimentary rocks, similar to those found elsewhere exposed in the Valles Marineris system and the chaotic terrain to the east of the region. Location near: 12.9oS, 49.5oW Image width: 3 km (1.9 mi) Illumination from: lower left Season: Southern Summer

Modeling the Rock Glacier Cycle

Science.gov (United States)

Anderson, R. S.; Anderson, L. S.

2016-12-01

Rock glaciers are common in many mountain ranges in which the ELA lies above the peaks. They represent some of the most identifiable components of today's cryosphere in these settings. Their oversteepened snouts pose often-overlooked hazards to travel in alpine terrain. Rock glaciers are supported by avalanches and by rockfall from steep headwalls. The winter's avalanche cone must be sufficiently thick not to melt entirely in the summer. The spatial distribution of rock glaciers reflects this dependence on avalanche sources; they are most common on lee sides of ridges where wind-blown snow augments the avalanche source. In the absence of rockfall, this would support a short, cirque glacier. Depending on the relationship between rockfall and avalanche patterns, "talus-derived" and "glacier-derived" rock glaciers are possible. Talus-derived: If the spatial distribution of rock delivery is similar to the avalanche pattern, the rock-ice mixture will travel an englacial path that is downward through the short accumulation zone before turning upward in the ablation zone. Advected debris is then delivered to the base of a growing surface debris layer that reduces the ice melt rate. The physics is identical to the debris-covered glacier case. Glacier-derived: If on the other hand rockfall from the headwall rolls beyond the avalanche cone, it is added directly to the ablation zone of the glacier. The avalanche accumulation zone then supports a pure ice core to the rock glacier. We have developed numerical models designed to capture the full range of glacier to debris-covered glacier to rock glacier behavior. The hundreds of meter lengths, tens of meters thicknesses, and meter per year speeds of rock glaciers are well described by the models. The model can capture both "talus-derived" and "glacier-derived" rock glaciers. We explore the dependence of glacier behavior on climate histories. As climate warms, a pure ice debris-covered glacier can transform to a much shorter rock

Critical issues in soft rocks

OpenAIRE

Milton Assis Kanji

2014-01-01

This paper discusses several efforts made to study and investigate soft rocks, as well as their physico-mechanical characteristics recognized up to now, the problems in their sampling and testing, and the possibility of its reproduction through artificially made soft rocks. The problems in utilizing current and widespread classification systems to some types of weak rocks are also discussed, as well as other problems related to them. Some examples of engineering works in soft rock or in soft ...

Attempt of groundwater dating using the drilled rock core. 1. Development of the rock sampling method for measurement of noble gases dissolved in interstitial water in rock

International Nuclear Information System (INIS)

Mahara, Yasunori

2002-01-01

Groundwater dating in low permeable rock is very difficult and impracticable, because we take a very long time to collect groundwater sample in a borehole and have to invest much fund in production of the in-situ groundwater sampler and in operation of it. If we can directly measure noble gases dissolved in interstitial groundwater in rock core, we have a big merit to estimate groundwater resident time easy. In this study, we designed and produced a high vacuum container to let dissolved noble gases diffuse until reaching in equilibrium, and we made a handling manual of the rock core into the container and a procedure to vacuum out air from the sealed container. We compared data sets of noble gas concentration obtained from rock cores and groundwater sample collected from boreholes in-situ. The measured rocks are pumice-tuff rock, mud rock and hornfels, which have their permeabilities of 10 -6 cm/s, 10 -9 cm/s and 10 -11 cm/s, respectively. Consequently, we evaluated the rock core method is better than the in-situ groundwater sampling method for low permeable rock. (author)

Current status of crushed rock and whole rock column studies

International Nuclear Information System (INIS)

Vine, E.N.; Daniels, W.R.; Rundberg, R.S.; Thompson, J.L.

1980-01-01

Measurements on a large number of crushed rock columns of tuff, granite, and argillite are discussed. The isotopes 85 Sr, 137 Cs, 133 Ba, 141 Ce, 152 Eu, /sup 95m/Tc, and 233 U were used. Flow rates were varied from approx. 30 to approx. 30000 m/y. Other parameters studied include isotope concentration and atmosphere. The sorption ratios calculated were compared with batch sorption ratios on the same samples. Methods of studying the movement of radionuclides through whole rock cores are described. The problems associated with sealing the cores to prevent leaking along the exterior surface and one possible solution are discussed. The strontium sorption ratio obtained by elution of one solid tuff core is compared with the batch and crushed rock column sorption ratios

Assessment of rock mass quality based on rock quality designation and rock block index. Taking the Borehole BS01 in Beishan HLW disposal repository as example

International Nuclear Information System (INIS)

Xu Jian; Wang Ju

2006-01-01

Rock mass quality assessment plays an important role in the security for all kinds of large-scale buildings, especially for the underground buildings. In this paper, based on two parameters of RQD and RBI, taking the Borehole BS01 as example, lots of measured data prove that the rock block index can reflect the integrity and corresponding variation of mechanical properties of core from Borehole BS01 to some extent. Meanwhile, the rock mass classification around the Borehole BS01 is given in this paper. Finally, comparison of the results for rock mass assessment between RBI and RQD is made. The research result shows that the rock block index has remarkable significance in engineering and advantages in rock mass quality assessment. (authors)

Rock suitability classification RSC 2012

Energy Technology Data Exchange (ETDEWEB)

McEwen, T. (ed.) [McEwen Consulting, Leicester (United Kingdom); Kapyaho, A. [Geological Survey of Finland, Espoo (Finland); Hella, P. [Saanio and Riekkola, Helsinki (Finland); Aro, S.; Kosunen, P.; Mattila, J.; Pere, T.

2012-12-15

This report presents Posiva's Rock Suitability Classification (RSC) system, developed for locating suitable rock volumes for repository design and construction. The RSC system comprises both the revised rock suitability criteria and the procedure for the suitability classification during the construction of the repository. The aim of the classification is to avoid such features of the host rock that may be detrimental to the favourable conditions within the repository, either initially or in the long term. This report also discusses the implications of applying the RSC system for the fulfilment of the regulatory requirements concerning the host rock as a natural barrier and the site's overall suitability for hosting a final repository of spent nuclear fuel.

Rock suitability classification RSC 2012

International Nuclear Information System (INIS)

McEwen, T.; Kapyaho, A.; Hella, P.; Aro, S.; Kosunen, P.; Mattila, J.; Pere, T.

2012-12-01

This report presents Posiva's Rock Suitability Classification (RSC) system, developed for locating suitable rock volumes for repository design and construction. The RSC system comprises both the revised rock suitability criteria and the procedure for the suitability classification during the construction of the repository. The aim of the classification is to avoid such features of the host rock that may be detrimental to the favourable conditions within the repository, either initially or in the long term. This report also discusses the implications of applying the RSC system for the fulfilment of the regulatory requirements concerning the host rock as a natural barrier and the site's overall suitability for hosting a final repository of spent nuclear fuel

Stantardization problems in radioisotopic techniques for measuring rock density and humidity

International Nuclear Information System (INIS)

Golubin, O.V.; Pavlov, L.S.

1977-01-01

A description of the main technical characteristics is given of radioisotope densimeters and hydrometers taken as a base for the State Standard design for field radioisotope instruments for measuring density and moisture of the soil and rocks

A novel design for storage of inner stress by colloidal processing on rock-like materials

Science.gov (United States)

Chen, Weichang; Wang, Sijing; Lekan Olatayo, Afolagboye; Fu, Huanran

2018-06-01

Inner stress exists in rocks, affecting rock engineering, yet has received very little attention and quantitative investigation because of uncertainty about its characteristics. Previous studies have suggested that the inner stresses of rock materials are closely related to their physical state variation. In this work, a novel mold was designed to simulate the storage process of inner stress in specimens composed of quartz sands and epoxy. Then, thermal tests were carried out to change the physical state of the specimens, and expansion of the specimens was monitored. The results indicated that inner stress could be partly locked by the mold and it could also be released by heating. It can be inferred from the analysis that one necessary condition of storage and release of inner stress is physical state variation. Additionally, by using an XRD method, the variations in the interplanar spacing of the quartz sands were detected, and the results reflect that inner stress could be locked-in aggregates (quartz sands) by a cement constraint (solid epoxy). The inner stress stored in quartz sands was calculated using height and interplanar spacing variations.

Investigations into the sorption of neptunium by loose rock from the cap rock of the Gorleben salt dome under aerobic and anaerobic conditions

International Nuclear Information System (INIS)

Muehlenweg, U.

1988-01-01

In the experiments with the natural loose rock the sorption behaviour of neptunium was essentially determined by the chemical form in which the neptunium occurred in the ground waters. Under aerobic conditions with Eh values of 300 mV, neptunium in its oxidation state +5 occurred. At a pH of 2 + , and at pH > 8 as carbonato complex. The found neptunium species were relatively mobile, with sorption values from 1 ml/g to 20 ml/g. The sorption of neptunium is comparable to that of alkali and alkaline earth ions, such as Cs + or Sr 2+ . Cations attached to the rock surface are exchanged for NpO 2 + . Sorption in this case is reversible. (orig.) [de

Rocking pneumonia

OpenAIRE

Rijkers, Ger T.; Rodriguez Gomez, Maria

2017-01-01

Ever since Chuck Berry coined the term “rocking pneumonia” in his 1956 song “Roll over Beethoven”, pneumonia has been mentioned frequently in modern blues and rock songs. We analyzed the lyrics of these songs to examine how various elements of pneumonia have been represented in popular music, specifically the cause of pneumonia, the risk groups, comorbidity (such as the boogie woogie flu), the clinical symptoms, and treatment and outcome. Up to this day, songwriters suggest that pneumonia is ...

Interpretation of stress measurements around mining cavities in rock salt - a finite-element study

International Nuclear Information System (INIS)

Heusermann, S.

1986-01-01

Finite-element studies of stress measurements using the overcoring method and of large drift fields in rock salt show that the measurements are affected by local stress relaxation occurring near the test borehole and by general time-dependent stress redistribution in the marginal zones of adjacent drifts. Analysis of the overcoring method indicates that the following local effects have to be considered in the interpretation of the test results as opposed to measurements in elastic rock: The inelastic deformation behaviour of rock salt causes stress relaxation at the pilot borehole which can lead to an underestimation of the actual stress state in rock. During overcoring considerable inelastic deformations occur in rock salt which demand a modified interpretation of the measurements and as a result of stress relaxation at the borehole various tests conditions, such as overcoring diameter, pilot borehole diameter and time between drilling and overcoring, have an effect on the test results. (orig./PW)

Friction of hard surfaces and its application in earthquakes and rock slope stability

Science.gov (United States)

Sinha, Nitish; Singh, Arun K.; Singh, Trilok N.

2018-05-01

In this article, we discuss the friction models for hard surfaces and their applications in earth sciences. The rate and state friction (RSF) model, which is basically modified form of the classical Amontons-Coulomb friction laws, is widely used for explaining the crustal earthquakes and the rock slope failures. Yet the RSF model has further been modified by considering the role of temperature at the sliding interface known as the rate, state and temperature friction (RSTF) model. Further, if the pore pressure is also taken into account then it is stated as the rate, state, temperature and pore pressure friction (RSTPF) model. All the RSF models predict a critical stiffness as well as a critical velocity at which sliding behavior becomes stable/unstable. The friction models are also used for predicting time of failure of the rock mass on an inclined plane. Finally, the limitation and possibilities of the proposed friction models are also highlighted.

Examining the relation between rock mass cuttability index and rock drilling properties

Science.gov (United States)

Yetkin, Mustafa E.; Özfırat, M. Kemal; Yenice, Hayati; Şimşir, Ferhan; Kahraman, Bayram

2016-12-01

Drilling rate is a substantial index value in drilling and excavation operations at mining. It is not only a help in determining physical and mechanical features of rocks, but also delivers strong estimations about instantaneous cutting rates. By this way, work durations to be finished on time, proper machine/equipment selection and efficient excavation works can be achieved. In this study, physical and mechanical properties of surrounding rocks and ore zones are determined by investigations carried out on specimens taken from an underground ore mine. Later, relationships among rock mass classifications, drillability rates, cuttability, and abrasivity have been investigated using multi regression analysis. As a result, equations having high regression rates have been found out among instantaneous cutting rates and geomechanical properties of rocks. Moreover, excavation machine selection for the study area has been made at the best possible interval.

Rock properties data base

Energy Technology Data Exchange (ETDEWEB)

Jackson, R.; Gorski, B.; Gyenge, M.

1991-03-01

As mining companies proceed deeper and into areas whose stability is threatened by high and complex stress fields, the science of rock mechanics becomes invaluable in designing underground mine strata control programs. CANMET's Mining Research Laboratories division has compiled a summary of pre- and post-failure mechanical properties of rock types which were tested to provide design data. The 'Rock Properties Data Base' presents the results of these tests, and includes many rock types typical of Canadian mine environments. The data base also contains 'm' and 's' values determined using Hoek and Brown's failure criteria for both pre- and post-failure conditions. 7 refs., 3 tabs., 9 figs., 1 append.

Numerical modelling of fluid-rock interactions: Lessons learnt from carbonate rocks diagenesis studies

Science.gov (United States)

Nader, Fadi; Bachaud, Pierre; Michel, Anthony

2015-04-01

Quantitative assessment of fluid-rock interactions and their impact on carbonate host-rocks has recently become a very attractive research topic within academic and industrial realms. Today, a common operational workflow that aims at predicting the relevant diagenetic processes on the host rocks (i.e. fluid-rock interactions) consists of three main stages: i) constructing a conceptual diagenesis model including inferred preferential fluids pathways; ii) quantifying the resulted diagenetic phases (e.g. depositing cements, dissolved and recrystallized minerals); and iii) numerical modelling of diagenetic processes. Most of the concepts of diagenetic processes operate at the larger, basin-scale, however, the description of the diagenetic phases (products of such processes) and their association with the overall petrophysical evolution of sedimentary rocks remain at reservoir (and even outcrop/ well core) scale. Conceptual models of diagenetic processes are thereafter constructed based on studying surface-exposed rocks and well cores (e.g. petrography, geochemistry, fluid inclusions). We are able to quantify the diagenetic products with various evolving techniques and on varying scales (e.g. point-counting, 2D and 3D image analysis, XRD, micro-CT and pore network models). Geochemical modelling makes use of thermodynamic and kinetic rules as well as data-bases to simulate chemical reactions and fluid-rock interactions. This can be through a 0D model, whereby a certain process is tested (e.g. the likelihood of a certain chemical reaction to operate under specific conditions). Results relate to the fluids and mineral phases involved in the chemical reactions. They could be used as arguments to support or refute proposed outcomes of fluid-rock interactions. Coupling geochemical modelling with transport (reactive transport model; 1D, 2D and 3D) is another possibility, attractive as it provides forward simulations of diagenetic processes and resulting phases. This

Evaluation of dynamic characteristics of hard rock based on numerical simulations of in situ rock tests

International Nuclear Information System (INIS)

Yamagami, Yuya; Ikusada, Koji; Jiang, Yujing

2009-01-01

In situ rock tests of hard rock of conglomerate in which discontinuities in high angle are dominant were conducted. In this study, in order to confirm the validity of the test results and the test condition, and in order to elucidate the deformation behaviour and the mechanism of shear strength of the rock mass, the numerical simulations of the in situ rock tests by using distinct element method were performed. As a result, it was clarified that the behaviour of the rock mass strongly depends on both geometrical distribution of discontinuities and those mechanical properties. It is thought that a series of evaluation processes showed in this study contribute to improve the reliability of the dynamic characteristic evaluation of the rock mass. (author)

Soil/Rock Properties Laboratory

Data.gov (United States)

Federal Laboratory Consortium — Soil/Rock Properties LaboratoryLocation: Spokane SiteThe Soil/Rock Properties Laboratory is contained in the soils bay, a 4,700 sq. ft. facility that provides space...

Rock Cycle Roulette.

Science.gov (United States)

Schmidt, Stan M.; Palmer, Courtney

2000-01-01

Introduces an activity on the rock cycle. Sets 11 stages representing the transitions of an earth material in the rock cycle. Builds six-sided die for each station, and students move to the stations depending on the rolling side of the die. Evaluates students by discussing several questions in the classroom. Provides instructional information for…

Igneous rocks formed by hypervelocity impact

Science.gov (United States)

Osinski, Gordon R.; Grieve, Richard A. F.; Bleacher, Jacob E.; Neish, Catherine D.; Pilles, Eric A.; Tornabene, Livio L.

2018-03-01

Igneous rocks are the primary building blocks of planetary crusts. Most igneous rocks originate via decompression melting and/or wet melting of protolith lithologies within planetary interiors and their classification and compositional, petrographic, and textural characteristics, are well-studied. As our exploration of the Solar System continues, so too does the inventory of intrusive and extrusive igneous rocks, settings, and processes. The results of planetary exploration have also clearly demonstrated that impact cratering is a ubiquitous geological process that has affected, and will continue to affect, all planetary objects with a solid surface, whether that be rock or ice. It is now recognized that the production of igneous rocks is a fundamental outcome of hypervelocity impact. The goal of this review is to provide an up-to-date synthesis of our knowledge and understanding of igneous rocks formed by hypervelocity impact. Following a brief overview of the basics of the impact process, we describe how and why melts are generated during impact events and how impact melting differs from endogenic igneous processes. While the process may differ, we show that the products of hypervelocity impact can share close similarities with volcanic and shallow intrusive igneous rocks of endogenic origin. Such impact melt rocks, as they are termed, can display lobate margins and cooling cracks, columnar joints and at the hand specimen and microscopic scale, such rocks can display mineral textures that are typical of volcanic rocks, such as quench crystallites, ophitic, porphyritic, as well as features such as vesicles, flow textures, and so on. Historically, these similarities led to the misidentification of some igneous rocks now known to be impact melt rocks as being of endogenic origin. This raises the question as to how to distinguish between an impact versus an endogenic origin for igneous-like rocks on other planetary bodies where fieldwork and sample analysis may not

Surface motion of active rock glaciers in the Sierra Nevada, California, USA: inventory and a case study using InSAR

Science.gov (United States)

L. Liu; C.I. Millar; R.D. Westfall; H.A. Zebker

2013-01-01

Despite the abundance of rock glaciers in the Sierra Nevada of California, USA, few efforts have been made to measure their surface flow. Here we use the interferometric synthetic aperture radar (InSAR) technique to compile a~benchmark inventory describing the kinematic state of 59 active rock glaciers in this region. Statistically, these rock glaciers moved at...

Litho stratigraphy of precambrian rocks in middle Xingu river basin -Altamira, Para state, Brazil

International Nuclear Information System (INIS)

Santos, M.V. dos; Sousa Filho, E.E. dos; Tassinari, C.C.G.

1988-01-01

The basement rocks from the Xingu river is divided into five litho stratigraphic units. They are broadly characterized by domains of ortho and para gneisses, volcano-sedimentary sequences, migmatites and by syntectonic and latetectonic granitoids. In addition acid to intermediate volcanics (Iriri formation) and several sub-volcanic granitic plutons (Maloquinha suite) also occur within the investigated area, as well as basic intrusions and minor arenous sediments covers, slightly metamorphosed. Geochronological studies carried out on the basement rocks and on the volcanics demonstrates an geologic evolution restricted to the trans Amazonian cycle (2.1 - 1.9 Ga). Sr isotopic evolution (high initial 87 Sr/ 86 Sr ratios) suggest that strong reworking of crustal material occurred at this time, in association with the tectonic evolution of the Maroni-Itacaiunas mobile belt related to the lower proterozoic, which borders the northern and northerneast part of the Archean central Amazonian province. (author)

Transporting radioactive rock

International Nuclear Information System (INIS)

Pearce, G.

1990-01-01

The case is made for exempting geological specimens from the IAEA Regulations for Safer Transport of Radioactive Materials. It is pointed out that many mineral collectors in Devon and Cornwall may be unwittingly infringing these regulations by taking naturally radioactive rocks and specimens containing uranium ores. Even if these collectors are aware that these rocks are radioactive, and many are not, few have the necessary equipment to monitor the activity levels. If the transport regulations were to be enforced alarm could be generated and the regulations devalued in case of an accident. The danger from a spill of rock specimens is negligible compared with an accident involving industrial or medical radioactive substances yet would require similar special treatment. (UK)

The Usability of Noise Level from Rock Cutting for the Prediction of Physico-Mechanical Properties of Rocks

Science.gov (United States)

Delibalta, M. S.; Kahraman, S.; Comakli, R.

2015-11-01

Because the indirect tests are easier and cheaper than the direct tests, the prediction of rock properties from the indirect testing methods is important especially for the preliminary investigations. In this study, the predictability of the physico-mechanical rock properties from the noise level measured during cutting rock with diamond saw was investigated. Noise measurement test, uniaxial compressive strength (UCS) test, Brazilian tensile strength (BTS) test, point load strength (Is) test, density test, and porosity test were carried out on 54 different rock types in the laboratory. The results were statistically analyzed to derive estimation equations. Strong correlations between the noise level and the mechanical rock properties were found. The relations follow power functions. Increasing rock strength increases the noise level. Density and porosity also correlated strongly with the noise level. The relations follow linear functions. Increasing density increases the noise level while increasing porosity decreases the noise level. The developed equations are valid for the rocks with a compressive strength below 150 MPa. Concluding remark is that the physico-mechanical rock properties can reliably be estimated from the noise level measured during cutting the rock with diamond saw.

Location-Related Differences in Weathering Behaviors and Populations of Culturable Rock-Weathering Bacteria Along a Hillside of a Rock Mountain.

Science.gov (United States)

Wang, Qi; Wang, Rongrong; He, Linyan; Sheng, Xiafang

2017-05-01

Bacteria play important roles in rock weathering, elemental cycling, and soil formation. However, little is known about the weathering potential and population of bacteria inhabiting surfaces of rocks. In this study, we isolated bacteria from the top, middle, and bottom rock samples along a hillside of a rock (trachyte) mountain as well as adjacent soils and characterized rock-weathering behaviors and populations of the bacteria. Per gram of rock or surface soil, 10 6 -10 7 colony forming units were obtained and total 192 bacteria were isolated. Laboratory rock dissolution experiments indicated that the proportions of the highly effective Fe (ranging from 67 to 92 %), Al (ranging from 40 to 48 %), and Cu (ranging from 54 to 81 %) solubilizers were significantly higher in the top rock and soil samples, while the proportion of the highly effective Si (56 %) solubilizers was significantly higher in the middle rock samples. Furthermore, 78, 96, and 6 % of bacteria from the top rocks, soils, and middle rocks, respectively, significantly acidified the culture medium (pH bacteria (79 %) from the rocks were different to those from the soils and most of them (species level) have not been previously reported. Furthermore, location-specific rock-weathering bacterial populations were found and Bacillus species were the most (66 %) frequently isolated rock-weathering bacteria in the rocks based on cultivation methods. Notably, the top rocks and soils had the highest and lowest diversity of rock-weathering bacterial populations, respectively. The results suggested location-related differences in element (Si, Al, Fe, and Cu) releasing effectiveness and communities of rock-weathering bacteria along the hillside of the rock mountain.

Etiology and Use of the “Hanging Drop” Technique: A Review

Science.gov (United States)

Todorov, Ludmil; VadeBoncouer, Timothy

2014-01-01

Background. The hanging drop (HD) technique presumably relies on the presence of subatmospheric epidural pressure. It is not clear whether this negative pressure is intrinsic or an artifact and how it is affected by body position. There are few data to indicate how often HD is currently being used. Methods. We identified studies that measured subatmospheric pressures and looked at the effect of the sitting position. We also looked at the technique used for cervical and thoracic epidural anesthesia in the last 10 years. Results. Intrinsic subatmospheric pressures were measured in the thoracic and cervical spine. Three trials studied the effect of body position, indicating a higher incidence of subatmospheric pressures when sitting. The results show lower epidural pressure (−10.7 mmHg) with the sitting position. 28.8% of trials of cervical and thoracic epidural anesthesia that documented the technique used, utilized the HD technique. When adjusting for possible bias, the rate of HD use can be as low as 11.7%. Conclusions. Intrinsic negative pressure might be present in the cervical and thoracic epidural space. This effect is more pronounced when sitting. This position might be preferable when using HD. Future studies are needed to compare it with the loss of resistance technique. PMID:24839558

Etiology and Use of the “Hanging Drop” Technique: A Review

Directory of Open Access Journals (Sweden)

Ludmil Todorov

2014-01-01

Full Text Available Background. The hanging drop (HD technique presumably relies on the presence of subatmospheric epidural pressure. It is not clear whether this negative pressure is intrinsic or an artifact and how it is affected by body position. There are few data to indicate how often HD is currently being used. Methods. We identified studies that measured subatmospheric pressures and looked at the effect of the sitting position. We also looked at the technique used for cervical and thoracic epidural anesthesia in the last 10 years. Results. Intrinsic subatmospheric pressures were measured in the thoracic and cervical spine. Three trials studied the effect of body position, indicating a higher incidence of subatmospheric pressures when sitting. The results show lower epidural pressure (−10.7 mmHg with the sitting position. 28.8% of trials of cervical and thoracic epidural anesthesia that documented the technique used, utilized the HD technique. When adjusting for possible bias, the rate of HD use can be as low as 11.7%. Conclusions. Intrinsic negative pressure might be present in the cervical and thoracic epidural space. This effect is more pronounced when sitting. This position might be preferable when using HD. Future studies are needed to compare it with the loss of resistance technique.

The analysis of creep characteristics of the surrounding rock of the carbonaceous rock tunnel based on Singh-Mitchell model

Science.gov (United States)

Luo, Junhui; Mi, Decai; Ye, Qiongyao; Deng, Shengqiang; Zeng, Fuquan; Zeng, Yongjun

2018-01-01

Carbonaceous rock has the characteristics of easy disintegration, softening, swelling and environmental sensitivity, which belongs to soft surrounding rock, and the deformation during excavation and long-term stability of the surrounding rock of carbonaceous rock tunnel are common problems in the construction of carbonaceous rock tunnel. According to the above, the Monitor and measure the displacement, temperature and osmotic pressure of the surrounding carbonaceous rock of the tunnel of Guangxi Hebai highway. Then it based on the obtaining data to study the creep mechanism of surrounding rock using Singh-Mitchell model and predict the deformation of surrounding rock before the tunnel is operation. The results show that the Singh-Mitchell creep model can effectively analyse and predict the deformation development law of surrounding rock of tunnel without considering temperature and osmotic pressure, it can provide reference for the construction of carbonaceous rock tunnel and the measures to prevent and reinforce it..

Solid as a rock

International Nuclear Information System (INIS)

Pincus, H.J.

1984-01-01

Recent technologic developments have required a more comprehensive approach to the behavior of rock mass or rock substance plus discontinuities than was adequate previously. This work considers the inherent problems in such operations as the storage of hot or cold fluids in caverns and aquifers, underground storage of nuclear waste, underground recovery of heat from hydrocarbon fuels, tertiary recovery of oil by thermal methods, rapid excavation of large openings at shallow to great depths and in hostile environments, and retrofitting of large structures built on or in rock. The standardization of methods for determining rock properties is essential to all of the activities described, for use not only in design and construction but also in site selection and post-construction monitoring. Development of such standards is seen as a multidisciplinary effort

The physical principles of rock magnetism

CERN Document Server

Stacey, Frank

1974-01-01

Developments in Solid Earth Geophysics 5: The Physical Principles of Rock Magnetism explores the physical principles of rock magnetism, with emphasis on the properties of finely divided magnetic materials. It discusses the origin and stability of rock magnetizations, the role of remanent magnetism in interpreting magnetic surveys, magnetic anisotropy as an indicator of rock fabric, and the relationship between piezomagnetic changes and seismic activity. Organized into 13 chapters, this volume discusses the properties of solids, magnetite and hematite grains, and rocks with magnetite grains

TREATMENT OF METHANOLIC WASTEWATER BY ANAEROBIC DOWN-FLOW HANGING SPONGE (ANDHS) REACTOR AND UASB REACTOR

Science.gov (United States)

Sumino, Haruhiko; Wada, Keiji; Syutsubo, Kazuaki; Yamaguchi, Takashi; Harada, Hideki; Ohashi, Akiyoshi

Anaerobic down-flow hanging sponge (AnDHS) reactor and UASB reactor were operated at 30℃ for over 400 days in order to investigate the process performance and the sludge characteristics of treating methanolic wastewater (2 gCOD/L). The settings OLR of AnDHS reactor and of UASB reactor were 5.0 -10.0 kgCOD/m3/d and 5.0 kgCOD/m3/d. The average of the COD removal demonstrated by both reactors were over 90% throughout the experiment. From the results of methane producing activities and the PCR-DGGE method, most methanol was directly converted to methane in both reactors. The conversion was carried out by different methanogens: one closely related to Methanomethylovorans hollandica in the AnDHS retainted sludge and the other closely related to Methanosarcinaceae and Metanosarciales in the UASB retainted sludge.

30 CFR 57.3461 - Rock bursts.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Rock bursts. 57.3461 Section 57.3461 Mineral...-Underground Only § 57.3461 Rock bursts. (a) Operators of mines which have experienced a rock burst shall— (1) Within twenty four hours report to the nearest MSHA office each rock burst which: (i) Causes persons to...

Sorption of cesium in intact rock

International Nuclear Information System (INIS)

Puukko, E.

2014-04-01

The mass distribution coefficient K d is used in performance assessment (PA) to describe sorption of a radionuclide on rock. The R d is determined using crushed rock which causes uncertainty in converting the R d values to K d values for intact rock. This work describes a method to determine the equilibrium of sorption on intact rock. The rock types of the planned Olkiluoto waste disposal site were T-series mica gneiss (T-MGN), T-series tonalite granodiorite granite gneiss (T-TGG), P-series tonalite granodiorite granite gneiss (P-TGG) and pegmatitic granite (PGR). These rocks contain different amount of biotite which is the main sorbing mineral. The sorption of cesium on intact rock slices was studied by applying an electrical field to speed up migration of cesium into the rock. Cesium is in the solution as a noncomplex cation Cs + and it is sorbed by ion exchange. The tracer used in the experiments was 134 Cs. The experimental sorption on the intact rock is compared with values calculated using the in house cation exchange sorption model (HYRL model) in PHREEQC program. The observed sorption on T-MGN and T-TGG rocks was close to the calculated values. Two PGR samples were from a depth of 70 m and three samples were from a depth of 150 m. Cesium sorbed more than predicted on the two 70 m PGR samples. The sorption of Cs on the three 150 m PGR samples was small which was consistent with the calculations. The pegmatitic granite PGR has the smallest content of biotite of the four rock types. In the case of P-TGG rock the observed values of sorption were only half of the calculated values. Two kind of slices were cut from P-TGG drill core. The slices were against and to the direction of the foliation of the biotite rims. The sorption of cesium on P-TGG rock was same in both cases. The results indicated that there was no effect of the directions of the electric field and the foliation of biotite in the P-TGG rock. (orig.)

A new method to test rock abrasiveness based on physico-mechanical and structural properties of rocks

Directory of Open Access Journals (Sweden)

V.N. Oparin

2015-06-01

Full Text Available A new method to test rock abrasiveness is proposed based upon the dependence of rock abrasiveness on their structural and physico-mechanical properties. The article describes the procedure of presentation of properties that govern rock abrasiveness on a canonical scale by dimensionless components, and the integrated estimation of the properties by a generalized index. The obtained results are compared with the known classifications of rock abrasiveness.

Commercial potential of natural gas storage in lined rock caverns (LRC); FINAL

International Nuclear Information System (INIS)

NONE

1999-01-01

The geologic conditions in many regions of the United States will not permit the development of economical high-deliverability gas storage in salt caverns. These regions include the entire Eastern Seaboard; several northern states, notably Minnesota and Wisconsin; many of the Rocky Mountain States; and most of the Pacific Northwest. In late 1997, the United States Department of Energy (USDOE) Federal Energy Technology Center engaged Sofregaz US to investigate the commercialization potential of natural gas storage in Lined Rock Caverns (LRC). Sofregaz US teamed with Gaz de France and Sydkraft, who had formed a consortium, called LRC, to perform the study for the USDOE. Underground storage of natural gas is generally achieved in depleted oil and gas fields, aquifers, and solution-mined salt caverns. These storage technologies require specific geologic conditions. Unlined rock caverns have been used for decades to store hydrocarbons - mostly liquids such as crude oil, butane, and propane. The maximum operating pressure in unlined rock caverns is limited, since the host rock is never entirely impervious. The LRC technology allows a significant increase in the maximum operating pressure over the unlined storage cavern concept, since the gas in storage is completely contained with an impervious liner. The LRC technology has been under development in Sweden by Sydkraft since 1987. The development process has included extensive technical studies, laboratory testing, field tests, and most recently includes a storage facility being constructed in southern Sweden (Skallen). The LRC development effort has shown that the concept is technically and economically viable. The Skallen storage facility will have a rock cover of 115 meters (375 feet), a storage volume of 40,000 cubic meters (250,000 petroleum barrels), and a maximum operating pressure of 20 MPa (2,900 psi). There is a potential for commercialization of the LRC technology in the United States. Two regions were studied

Measurements of thermal properties of rocks

International Nuclear Information System (INIS)

Kumada, Toshiaki

2001-02-01

The report concerns the measurement of thermal conductivity and specific heat of supplied sedimental rock B and Funyu rock. The method of measurement of these properties was done with the method which was developed at 1997 and improved much in its accuracy by the present author et al. The porosity of sedimental rock B is 0.55, which is deduced from the density of rock (the porosity deduced from the difference between dry and water filled conditions is 0.42) and the shape and size of pores in rock are much different. Its thermal conductivity is 0.238 W/mK in dry and 1.152 W/mK in water filled conditions respectively, while the thermal conductivity of bentonite is 0.238 W/mK in dry and 1.152 W/mK in water saturated conditions. The difference of thermal conductivity between dry and water saturated conditions is little difference in sedimental rock B and bentonite at same porosity. The porosity of Funyu rock is 0.26 and the shape and size of pores in the rock are uniform. Its thermal conductivity is 0.914 W/mK in dry and 1.405 W/mK in water saturated conditions, while the thermal conductivity of bentonite is 0.606 W/mK in dry and 1.591 W/mK in water saturated conditions respectively. The correlation estimating thermal conductivity of rocks was derived based on Fricke correlation by presuming rocks as a suspension. (author)

Multiverso: Rock'n'Astronomy

Science.gov (United States)

Caballero, J. A.

2012-05-01

In the last few years, there have been several projects involving astronomy and classical music. But have a rock band ever appeared at a science conference or an astronomer at a rock concert? We present a project, Multiverso, in which we mix rock and astronomy, together with poetry and video art (Caballero, 2010). The project started in late 2009 and has already reached tens of thousands people in Spain through the release of an album, several concert-talks, television, radio, newspapers and the internet.

Rock Pore Structure as Main Reason of Rock Deterioration

Directory of Open Access Journals (Sweden)

Ondrášik Martin

2014-03-01

Full Text Available Crashed or dimensional rocks have been used as natural construction material, decoration stone or as material for artistic sculptures. Especially old historical towns not only in Slovakia have had experiences with use of stones for construction purposes for centuries. The whole buildings were made from dimensional stone, like sandstone, limestone or rhyolite. Pavements were made especially from basalt, andesite, rhyolite or granite. Also the most common modern construction material - concrete includes large amounts of crashed rock, especially limestone, dolostone and andesite.

Strength Assessment of Broken Rock Postgrouting Reinforcement Based on Initial Broken Rock Quality and Grouting Quality

Directory of Open Access Journals (Sweden)

Hongfa Xu

2017-01-01

Full Text Available To estimate postgrouting rock mass strength growth is important for engineering design. In this paper, using self-developed indoor pressure-grouting devices, 19 groups of test cubic blocks were made of the different water cement ratio grouting into the broken rock of three kinds of particle sizes. The shear strength parameters of each group under different conditions were tested. Then this paper presents a quantitative calculation method for predicting the strength growth of grouted broken rock. Relational equations were developed to investigate the relationship between the growth rates of uniaxial compressive strength (UCS, absolute value of uniaxial tensile strength (AUTS, internal friction angle, and cohesion for post- to pregrouting broken rock based on Mohr-Coulomb strength criterion. From previous test data, the empirical equation between the growth rate of UCS and the ratio of the initial rock mass UCS to the grout concretion UCS has been determined. The equations of the growth rates of the internal friction coefficient and UCS for grouting broken rock with rock mass rating (RMR and its increment have been established. The calculated results are consistent with the experimental results. These observations are important for engineered design of grouting reinforcement for broken rock mass.

Thermal inertia in thermal infrared: porosity and chemical components of rocks; Inercia termica no infravermelho termal: porosidade e componentes quimicos de rochas

Energy Technology Data Exchange (ETDEWEB)

Pacheco, Admilson P.; Ehlers, Ricardo Sandes [Universidade Federal Fluminense, Niteroi, RJ (Brazil); Vitorello, Icaro [Instituto de Pesquisas Espaciais (INPE), Sao Jose dos Campos, SP (Brazil)

1995-12-31

The effect of porosity, and the relation between thermal inertia values and chemical components were determined. The thermal inertia values and chemical components were determined. The thermal inertia determinations were performed using radiometric observations, in the range 8 to 14 {mu}, of the surface temperature variations of the sample, induced by an incident heat flux. The results show that the increase in porosity tends to reduce the thermal inertia values, when the rock is in a dry state. In the water saturation state, the inertia also tends to show small values, only for porous rocks with thermal inertia values larger than the water values. The acid rocks show thermal inertia values smaller than those of the basic rocks. The intermediate and basic rocks show strong positive correlation between thermal inertia and Si O{sub 2}. 7 refs., 3 figs

Hematopoietic Stem and Progenitor Cell Expansion in Contact with Mesenchymal Stromal Cells in a Hanging Drop Model Uncovers Disadvantages of 3D Culture.

Science.gov (United States)

Schmal, Olga; Seifert, Jan; Schäffer, Tilman E; Walter, Christina B; Aicher, Wilhelm K; Klein, Gerd

2016-01-01

Efficient ex vivo expansion of hematopoietic stem cells with a concomitant preservation of stemness and self-renewal potential is still an unresolved ambition. Increased numbers of methods approaching this issue using three-dimensional (3D) cultures were reported. Here, we describe a simplified 3D hanging drop model for the coculture of cord blood-derived CD34(+) hematopoietic stem and progenitor cells (HSPCs) with bone marrow-derived mesenchymal stromal cells (MSCs). When seeded as a mixed cell suspension, MSCs segregated into tight spheroids. Despite the high expression of niche-specific extracellular matrix components by spheroid-forming MSCs, HSPCs did not migrate into the spheroids in the initial phase of coculture, indicating strong homotypic interactions of MSCs. After one week, however, HSPC attachment increased considerably, leading to spheroid collapse as demonstrated by electron microscopy and immunofluorescence staining. In terms of HSPC proliferation, the conventional 2D coculture system was superior to the hanging drop model. Furthermore, expansion of primitive hematopoietic progenitors was more favored in 2D than in 3D, as analyzed in colony-forming assays. Conclusively, our data demonstrate that MSCs, when arranged with a spread (monolayer) shape, exhibit better HSPC supportive qualities than spheroid-forming MSCs. Therefore, 3D systems are not necessarily superior to traditional 2D culture in this regard.

Rock slope design guide.

Science.gov (United States)

2011-04-01

This Manual is intended to provide guidance for the design of rock cut slopes, rockfall catchment, and : rockfall controls. Recommendations presented in this manual are based on research presented in Shakoor : and Admassu (2010) entitled Rock Slop...

Rock Slope Design Criteria

Science.gov (United States)

2010-06-01

Based on the stratigraphy and the type of slope stability problems, the flat lying, Paleozoic age, sedimentary : rocks of Ohio were divided into three design units: 1) competent rock design unit consisting of sandstones, limestones, : and siltstones ...

Source rock potential of middle cretaceous rocks in Southwestern Montana

Science.gov (United States)

Dyman, T.S.; Palacas, J.G.; Tysdal, R.G.; Perry, W.J.; Pawlewicz, M.J.

1996-01-01

The middle Cretaceous in southwestern Montana is composed of a marine and nonmarine succession of predominantly clastic rocks that were deposited along the western margin of the Western Interior Seaway. In places, middle Cretaceous rocks contain appreciable total organic carbon (TOC), such as 5.59% for the Mowry Shale and 8.11% for the Frontier Formation in the Madison Range. Most samples, however, exhibit less than 1.0% TOC. The genetic or hydrocarbon potential (S1+S2) of all the samples analyzed, except one, yield less than 1 mg HC/g rock, strongly indicating poor potential for generating commercial amounts of hydrocarbons. Out of 51 samples analyzed, only one (a Thermopolis Shale sample from the Snowcrest Range) showed a moderate petroleum potential of 3.1 mg HC/g rock. Most of the middle Cretaceous samples are thermally immature to marginally mature, with vitrinite reflectance ranging from about 0.4 to 0.6% Ro. Maturity is high in the Pioneer Mountains, where vitrinite reflectance averages 3.4% Ro, and at Big Sky Montana, where vitrinite reflectance averages 2.5% Ro. At both localities, high Ro values are due to local heat sources, such as the Pioneer batholith in the Pioneer Mountains.

Impact of grain size and rock composition on simulated rock weathering

Science.gov (United States)

Israeli, Yoni; Emmanuel, Simon

2018-05-01

Both chemical and mechanical processes act together to control the weathering rate of rocks. In rocks with micrometer size grains, enhanced dissolution at grain boundaries has been observed to cause the mechanical detachment of particles. However, it remains unclear how important this effect is in rocks with larger grains, and how the overall weathering rate is influenced by the proportion of high- and low-reactivity mineral phases. Here, we use a numerical model to assess the effect of grain size on chemical weathering and chemo-mechanical grain detachment. Our model shows that as grain size increases, the weathering rate initially decreases; however, beyond a critical size no significant decrease in the rate is observed. This transition occurs when the density of reactive boundaries is less than ˜ 20 % of the entire domain. In addition, we examined the weathering rates of rocks containing different proportions of high- and low-reactivity minerals. We found that as the proportion of low-reactivity minerals increases, the weathering rate decreases nonlinearly. These simulations indicate that for all compositions, grain detachment contributes more than 36 % to the overall weathering rate, with a maximum of ˜ 50 % when high- and low-reactivity minerals are equally abundant in the rock. This occurs because selective dissolution of the high-reactivity minerals creates large clusters of low-reactivity minerals, which then become detached. Our results demonstrate that the balance between chemical and mechanical processes can create complex and nonlinear relationships between the weathering rate and lithology.

Epigenetic alterations of sedimentary rocks at deposits

International Nuclear Information System (INIS)

Komarova, G.V.; Kondrat'eva, I.A.; Zelenova, O.I.

1980-01-01

Notions are explained, and technique for studying epigenetic alterations of sedimentary rocks at uranium deposits is described. Main types of epigenetic transformations and their mineralogic-geochemical characteristics are considered. Rock alterations, accompanying uranium mineralization, can be related to 2 types: oxidation and reduction. The main mineralogic-geochemical property of oxidation transformations is epigenetic limonitization. Stratal limonitization in primary grey-coloured terrigenic rocks and in epigenetically reduced (pyritized) rocks, as well as in rock, subjected to epigenetic gleying, are characterized. Reduction type of epigenetic transformations is subdivided into sulphidic and non-sulphidic (gley) subtypes. Sulphidic transformations in grey-coloured terrigenic rocks with organic substance of carbonic row, in rocks, containing organic substance of oil row, sulphide transformations of sedimentary rocks, as well as gley transformations, are considered

A hollow sphere soft lithography approach for long-term hanging drop methods.

Science.gov (United States)

Lee, Won Gu; Ortmann, Daniel; Hancock, Matthew J; Bae, Hojae; Khademhosseini, Ali

2010-04-01

In conventional hanging drop (HD) methods, embryonic stem cell aggregates or embryoid bodies (EBs) are often maintained in small inverted droplets. Gravity limits the volumes of these droplets to less than 50 microL, and hence such cell cultures can only be sustained for a few days without frequent media changes. Here we present a new approach to performing long-term HD methods (10-15 days) that can provide larger media reservoirs in a HD format to maintain more consistent culture media conditions. To implement this approach, we fabricated hollow sphere (HS) structures by injecting liquid drops into noncured poly(dimethylsiloxane) mixtures. These structures served as cell culture chambers with large media volumes (500 microL in each sphere) where EBs could grow without media depletion. The results showed that the sizes of the EBs cultured in the HS structures in a long-term HD format were approximately twice those of conventional HD methods after 10 days in culture. Further, HS cultures showed multilineage differentiation, similar to EBs cultured in the HD method. Due to its ease of fabrication and enhanced features, this approach may be of potential benefit as a stem cell culture method for regenerative medicine.

Survival Times of Meter-Sized Rock Boulders on the Surface of Airless Bodies

Science.gov (United States)

Basilevsky, A. T.; Head, J. W.; Horz, F.; Ramsley, K.

2015-01-01

This study considers the survival times of meter-sized rock boulders on the surfaces of several airless bodies. As the starting point, we employ estimates of the survival times of such boulders on the surface of the Moon by[1], then discuss the role of destruction due to day-night temperature cycling, consider the meteorite bombardment environment on the considered bodies in terms of projectile flux and velocities and finally estimate the survival times. Survival times of meter-sized rocks on lunar surface: The survival times of hand specimen-sized rocks exposed to the lunar surface environment were estimated based on experiments modeling the destruction of rocks by meteorite impacts, combined with measurements of the lunar surface meteorite flux, (e.g.,[2]). For estimations of the survival times of meter-sized lunar boulders, [1] suggested a different approach based on analysis of the spatial density of boulders on the rims of small lunar craters of known absolute age. It was found that for a few million years, only a small fraction of the boulders ejected by cratering process are destroyed, for several tens of million years approx.50% are destroyed, and for 200-300 Ma, 90 to 99% are destroyed. Following [2] and other works, [1] considered that the rocks are mostly destroyed by meteorite impacts. Destruction of rocks by thermal-stress. However, high diurnal temperature variations on the surface of the Moon and other airless bodies imply that thermal stresses may also be a cause of surface rock destruction. Delbo et al. [3] interpreted the observed presence of fine debris on the surface of small asteroids as due to thermal surface cycling. They stated that because of the very low gravity on the surface of these bodies, ejecta from meteorite impacts should leave the body, so formation there of fine debris has to be due to thermal cycling. Based on experiments on heating-cooling of cm-scale pieces of ordinary and carbonaceous chondrites and theoretical modeling of

Weathering of rock 'Ginger'

Science.gov (United States)

1997-01-01

One of the more unusual rocks at the site is Ginger, located southeast of the lander. Parts of it have the reddest color of any material in view, whereas its rounded lobes are gray and relatively unweathered. These color differences are brought out in the inset, enhanced at the upper right. In the false color image at the lower right, the shape of the visible-wavelength spectrum (related to the abundance of weathered ferric iron minerals) is indicated by the hue of the rocks. Blue indicates relatively unweathered rocks. Typical soils and drift, which are heavily weathered, are shown in green and flesh tones. The very red color in the creases in the rock surface correspond to a crust of ferric minerals. The origin of the rock is uncertain; the ferric crust may have grown underneath the rock, or it may cement pebbles together into a conglomerate. Ginger will be a target of future super-resolution studies to better constrain its origin.Mars Pathfinder is the second in NASA's Discovery program of low-cost spacecraft with highly focused science goals. The Jet Propulsion Laboratory, Pasadena, CA, developed and manages the Mars Pathfinder mission for NASA's Office of Space Science, Washington, D.C. The Imager for Mars Pathfinder (IMP) was developed by the University of Arizona Lunar and Planetary Laboratory under contract to JPL. Peter Smith is the Principal Investigator. JPL is an operating division of the California Institute of Technology (Caltech).

An investigation of rock fall and pore water pressure using LIDAR in Highway 63 rock cuts.

Science.gov (United States)

2014-07-01

The purpose of this research work is compare LIDAR scanning measurements of rock fall with the natural changes in groundwater level to determining the effect of water pressures (levels) on rock fall. To collect the information of rock cut volume chan...

Experimental Studies on Permeability of Intact and Singly Jointed Meta-Sedimentary Rocks Under Confining Pressure

Science.gov (United States)

Wong, Louis Ngai Yuen; Li, Diyuan; Liu, Gang

2013-01-01