Biomechanical Analysis of Cuboid Osteotomy Lateral Column Lengthening for Stage II B Adult-Acquired Flatfoot Deformity: A Cadaveric Study

Directory of Open Access Journals (Sweden)

Haichao Zhou

2017-01-01

Full Text Available Purpose. To investigate the effect of cuboid osteotomy lateral column lengthening (LCL for the correction of stage II B adult-acquired flatfoot deformity in cadaver. Methods. Six cadaver specimens were loaded to 350 N. Flatfoot models were established and each was evaluated radiographically and pedobarographically in the following conditions: (1 intact foot, (2 flatfoot, and (3 cuboid osteotomy LCL (2, 3, 4, and 5 mm. Results. Compared with the flatfoot model, the LCLs showed significant correction of talonavicular coverage on anteroposterior radiographs and talus-first metatarsal angle on both anteroposterior and lateral radiographs (p<.05. Compared with the intact foot, the above angles of the LCLs showed no significant difference except the 2 mm LCL. In terms of forefoot pressure, medial pressure of the 2 mm LCL (p=.044 and lateral pressure of the 3, 4, and 5 mm LCLs showed statistical differences (p<.05, but lateral pressure of the 3 mm LCL was not more than the intact foot as compared to the 4 and 5 mm LCLs, which was less than medial pressure. Conclusion. Cuboid osteotomy LCL procedure avoids damage to subtalar joint and has a good effect on correction of stage II B adult-acquired flatfoot deformity with a 3 mm lengthening in cadavers.

Acquired cavo-varus deformity caused by an accessory calcaneus: a case report and literature review

International Nuclear Information System (INIS)

Singh Baghla, Davinder Paul; Shariff, Sajid; Bashir, Waseem A.

2010-01-01

We describe an unusual cause of an acquired cavo-varus foot deformity produced by progressive enlargement of an accessory calcaneal ossicle. A 13-year-old boy with constitutional plano-valgus flat feet noted a gradual change in foot shape associated with lateral ankle pain on ambulation following an inversion injury 2 years earlier. CT and MRI scans confirmed a large accessory calcaneal ossicle lying within the sinus tarsi, with associated marrow oedema. Following surgical excision of the ossicle, the foot returned to its original shape and the symptoms were alleviated. This is the fifth reported case of an accessory calcaneal ossicle, but the only case that has occurred in a flatfooted individual. We also present the first reported MRI images of the lesion confirming pathological marrow oedema as a response to mechanical stress. (orig.)

Avoiding unfavorable results in postburn contracture hand

Science.gov (United States)

Bhattacharya, Sameek

2013-01-01

Deformities of the hands are a fairly common sequel of burn especially in the developing world. This is because of high incidence of burns, limited access to standard treatment and rehabilitation. The best outcome of a burnt hand is when deformities are prevented from developing. A good functional result is possible when due consideration is paid to hands during resuscitation, excisional surgery, reconstructive surgery and physiotherapy. The post-burns deformities of hand develop due direct thermal damage or secondary to intrinsic minus position due to oedema or vascular insufficiency. During the acute phase the concerns are, maintenance circulation minimize oedema prevent unphysiological positioning and wound closure with autogenous tissue as soon as possible. The rehabilitation program during the acute phase starts from day one and goes on till the hand has healed and has regained full range of motion. Full blown hand contractures are challenging to correct and become more difficult as time passes. Long-standing cases often land up with attenuation of extensor apparatus leading to swan neck and boutonniere deformity, muscle shortening and bony ankylosis. The major and most common pitfall after contracture release is relapse. The treatment protocol of contracture is solely directed towards countering this tendency. This article aims to guide a surgeon in obtaining optimal hand function and avoid pit falls at different stages of management of hand burns. The reasons of an unfavourable outcome of a burnt hand are possible lack of optimal care in the acute phase, while planning and performing reconstructive procedure and during aftercare and rehabilitation. PMID:24501479

Outcomes of a Stepcut Lengthening Calcaneal Osteotomy for Adult-Acquired Flatfoot Deformity.

Science.gov (United States)

Demetracopoulos, Constantine A; Nair, Pallavi; Malzberg, Andrew; Deland, Jonathan T

2015-07-01

Lateral column lengthening is used to correct abduction deformity at the midfoot and improve talar head coverage in patients with flatfoot deformity. It was our hypothesis that following a stepcut lengthening calcaneal osteotomy (SLCO), patients would have adequate correction of the deformity, a high union rate of the osteotomy, and improvement in clinical outcome scores. We retrospectively reviewed 37 consecutive patients who underwent SLCO for the treatment of stage IIB flatfoot deformity with a minimum 2-year follow-up. Deformity correction was assessed using preoperative and postoperative weight-bearing radiographs. Healing of the osteotomy was assessed by computed tomography. Clinical outcomes included the FAOS and SF-36 questionnaires. The Wilcoxon signed-rank test was used to compare clinical outcome scores. An alpha level of .05 was deemed statistically significant. Healing of the osteotomy occurred at a mean of 7.7 weeks postoperatively. The talonavicular (TN) coverage angle improved from 34.0 to 8.8 (P lengthening. Level IV, retrospective case review. © The Author(s) 2015.

Evaluation of fingerprint deformation using optical coherence tomography

Science.gov (United States)

Gutierrez da Costa, Henrique S.; Maxey, Jessica R.; Silva, Luciano; Ellerbee, Audrey K.

2014-02-01

Biometric identification systems have important applications to privacy and security. The most widely used of these, print identification, is based on imaging patterns present in the fingers, hands and feet that are formed by the ridges, valleys and pores of the skin. Most modern print sensors acquire images of the finger when pressed against a sensor surface. Unfortunately, this pressure may result in deformations, characterized by changes in the sizes and relative distances of the print patterns, and such changes have been shown to negatively affect the performance of fingerprint identification algorithms. Optical coherence tomography (OCT) is a novel imaging technique that is capable of imaging the subsurface of biological tissue. Hence, OCT may be used to obtain images of subdermal skin structures from which one can extract an internal fingerprint. The internal fingerprint is very similar in structure to the commonly used external fingerprint and is of increasing interest in investigations of identify fraud. We proposed and tested metrics based on measurements calculated from external and internal fingerprints to evaluate the amount of deformation of the skin. Such metrics were used to test hypotheses about the differences of deformation between the internal and external images, variations with the type of finger and location inside the fingerprint.

Unusual case of cleft hand

Directory of Open Access Journals (Sweden)

Sahasrabudhe Parag

2007-01-01

Full Text Available We present a case of a six-year-old male child with cleft hand deformity involving the dominant right hand. It was a rare case of atypical cleft hand with no missing tissue but cleft extending to metacarpal level and associated hypoplasia of thumb and index finger. As per Manske′s classification of cleft hand our patient belongs to the Class III variety. There was associated malposition of the index finger with absence of first web space and syndactly of thumb and index finger at the metacarpal level. A modified Snow-Littler procedure was planned. The surgical plan involved closure of cleft, release of thumb and index finger syndactly and reconstruction of the first web space. The functional outcome was good considering hypoplasia of the index finger and thumb. Depending upon the function of the thumb tendon transfers can be planned to augment thumb function at a later date along with correction of rotational deformities of the index and middle finger.

A two-dimensional deformable phantom for quantitatively verifying deformation algorithms

Energy Technology Data Exchange (ETDEWEB)

Kirby, Neil; Chuang, Cynthia; Pouliot, Jean [Department of Radiation Oncology, University of California San Francisco, San Francisco, California 94143-1708 (United States)

2011-08-15

Purpose: The incorporation of deformable image registration into the treatment planning process is rapidly advancing. For this reason, the methods used to verify the underlying deformation algorithms must evolve equally fast. This manuscript proposes a two-dimensional deformable phantom, which can objectively verify the accuracy of deformation algorithms, as the next step for improving these techniques. Methods: The phantom represents a single plane of the anatomy for a head and neck patient. Inflation of a balloon catheter inside the phantom simulates tumor growth. CT and camera images of the phantom are acquired before and after its deformation. Nonradiopaque markers reside on the surface of the deformable anatomy and are visible through an acrylic plate, which enables an optical camera to measure their positions; thus, establishing the ground-truth deformation. This measured deformation is directly compared to the predictions of deformation algorithms, using several similarity metrics. The ratio of the number of points with more than a 3 mm deformation error over the number that are deformed by more than 3 mm is used for an error metric to evaluate algorithm accuracy. Results: An optical method of characterizing deformation has been successfully demonstrated. For the tests of this method, the balloon catheter deforms 32 out of the 54 surface markers by more than 3 mm. Different deformation errors result from the different similarity metrics. The most accurate deformation predictions had an error of 75%. Conclusions: The results presented here demonstrate the utility of the phantom for objectively verifying deformation algorithms and determining which is the most accurate. They also indicate that the phantom would benefit from more electron density heterogeneity. The reduction of the deformable anatomy to a two-dimensional system allows for the use of nonradiopaque markers, which do not influence deformation algorithms. This is the fundamental advantage of this

Systematics of triaxial deformation in Xe, Ba, and Ce nuclei

International Nuclear Information System (INIS)

Yan, J.; Vogel, O.; von Brentano, P.; Gelberg, A.

1993-01-01

The (β,γ) deformation parameters of even-even Xe, Ba, and Ce nuclei have been calculated by using the triaxial rotor model. Deformation parameters calculated, on one hand, from decay properties and, on the other hand, from energies are in good agreement. The smooth dependence of the deformation parameters on Z and N is discussed. The results are compared with those extracted from properties of odd-A nuclei

Nucleus spectroscopy: extreme masses and deformations

International Nuclear Information System (INIS)

Theisen, Ch.

2009-12-01

The author proposes a synthesis of research activities performed since 1995 in the field of experimental nuclear physics, and more particularly in the investigation of two nucleus extreme states: deformation on the one hand, heavy and very heavy nuclei on the other hand. After a presentation of the context of investigations on deformation, rotation, and heavy nuclei, he gives an overview of developments regarding instruments (gamma spectrometers, detection of fission fragments, and detection at the focal plane of spectrometers or separators) and analysis techniques. Experiments and results are then reported and discussed, concerning super-deformed states with a high angular moment, spectroscopy of neutron-rich nuclei, very heavy nuclei close to nucleus map borders. He finally draws perspectives for middle and long term studies on the heaviest nuclei

Hand assessment with the E-Cone in rheumatoid arthritis and hand osteoarthritis

NARCIS (Netherlands)

van Merendonk, N.; van Alebeek, V.; Spreeuwers, Lieuwe Jan; Spreeuwers, D.; Kroon, P.J.; Roorda, L.; Dekker, J.; Hoeksma, A.F.

2013-01-01

Background: Rheumatoid arthritis (RA) is a systemic inflammatory, progressive disease resulting in deformities of the hand. Besides synovitis, tenosynovitis of the extrinsic flexor tendons is one of the initial features of RA, leading to friction and consequently to an imbalanced coordination of the

Hand biometric recognition based on fused hand geometry and vascular patterns.

Science.gov (United States)

Park, GiTae; Kim, Soowon

2013-02-28

A hand biometric authentication method based on measurements of the user's hand geometry and vascular pattern is proposed. To acquire the hand geometry, the thickness of the side view of the hand, the K-curvature with a hand-shaped chain code, the lengths and angles of the finger valleys, and the lengths and profiles of the fingers were used, and for the vascular pattern, the direction-based vascular-pattern extraction method was used, and thus, a new multimodal biometric approach is proposed. The proposed multimodal biometric system uses only one image to extract the feature points. This system can be configured for low-cost devices. Our multimodal biometric-approach hand-geometry (the side view of the hand and the back of hand) and vascular-pattern recognition method performs at the score level. The results of our study showed that the equal error rate of the proposed system was 0.06%.

Reiter's Syndrome associated with the Acquired Immunodeficiency Syndrome: a case report

Directory of Open Access Journals (Sweden)

J.B.N.S. Malta

Full Text Available The association of Reiter's Syndrome (RS with the Acquired Immunodeficiency Syndrome (AIDS is seldom mentioned in the medical literature. This report illustrates this relationship in a 46 years old male patient suffering from AIDS (CD4+ = 240 cells/mm³, CD8+ = 1,301 cells/mm³ and viral load = 330,000 copies/ml, pulmonary tuberculosis (positive catarrhal bacilluscopy, and RS. The diagnosis of RS was based on the combination of dermatological and articular alterations. The patient's cutaneous lesions were characterized by exfoliation and the formation of crusts located on the face, scalp, genitals, hands, and feet; onychodystrophy with opacity; yellowish coloring; and hyperkeratosis of the nails. Articular lesions led to progressive deformity of phalangeal joints of the hands, and intensive arthralgia, mainly of the larger joints (shoulders, elbows, hips and knees. AIDS treatment was administered with anti-retroviral drugs (zidovudine and didanosine; for tuberculosis (isoniazid, rifampicine, and pyrazinamide; and (prednisone and inometacine for the RS. The patient recovered with the improvement of articular symptoms; however, on the eighth day of treatment, the patient showed significant hemoptysis and hypovolemic shock, and died. The association of RS and HIV infection is reviewed.

Amniotic Constriction Bands: Secondary Deformities and Their Treatments.

Science.gov (United States)

Drury, Benjamin T; Rayan, Ghazi M

2018-01-01

The purpose of this study was to report the surgical treatment experience of patients with amniotic constriction bands (ACB) over a 35-year interval and detail consequential limb deformities with emphasis on hands and upper extremities, along with the nature and frequency of their surgical treatment methods. Fifty-one patients were identified; 26 were males and 25 females. The total number of deformities was listed. The total number of operations, individual procedures, and operations plus procedures that were done for each patient and their frequency were recorded. The total number of operations was 117, and total number of procedures was 341. More procedures were performed on the upper extremity (85%) than the lower extremity (15%). Including the primary deformity ACB, 16 different hand deformities secondary to ACB were encountered. Sixteen different surgical methods for the upper extremity were utilized; a primary procedure for ACB and secondary reconstructions for all secondary deformities. Average age at the time of the first procedure was 9.3 months. The most common procedures performed, in order of frequency, were excision of ACB plus Z-plasty, release of partial syndactyly, release of fenestrated syndactyly, full-thickness skin grafts, resection of digital bony overgrowth from amputation stumps, and deepening of first and other digital web spaces. Many hand and upper extremity deformities secondary to ACB are encountered. Children with ACB may require more than one operation including multiple procedures. Numerous surgical methods of reconstruction for these children's secondary deformities are necessary in addition to the customary primary procedure of excision of ACB and Z-plasty.

Unilateral Cleft Hand with Cleft Foot

Science.gov (United States)

Baba, Asif Nazir; Bhat, Yasmeen J.; Ahmed, Sheikh Mushtaq; Nazir, Abid

2009-01-01

Congenital anomalies of the hand form an important class of congenital malformations. They have a huge functional importance because of the part played by the hand in the daily activities of a person. The deformities also have significant cosmetic significance and may also be associated with other anomalies. Amongst the congenital anomalies, central deficiency or cleft hand is relatively rare. The association of cleft foot with cleft hand is an even more rare occurance. We present a case report of a 6 year old child, born of a non-consanginous marriage, having congenital central deficiency of ipsilateral hand and foot. PMID:21475543

Hand Biometric Recognition Based on Fused Hand Geometry and Vascular Patterns

Science.gov (United States)

Park, GiTae; Kim, Soowon

2013-01-01

A hand biometric authentication method based on measurements of the user's hand geometry and vascular pattern is proposed. To acquire the hand geometry, the thickness of the side view of the hand, the K-curvature with a hand-shaped chain code, the lengths and angles of the finger valleys, and the lengths and profiles of the fingers were used, and for the vascular pattern, the direction-based vascular-pattern extraction method was used, and thus, a new multimodal biometric approach is proposed. The proposed multimodal biometric system uses only one image to extract the feature points. This system can be configured for low-cost devices. Our multimodal biometric-approach hand-geometry (the side view of the hand and the back of hand) and vascular-pattern recognition method performs at the score level. The results of our study showed that the equal error rate of the proposed system was 0.06%. PMID:23449119

Meat Grinder Injury to the Hand: Serial Cases

OpenAIRE

Lubis, Nur Rachmat

2012-01-01

Introduction.Although meat grinder injury to the hand is not a common case, it causes a wide spectrum of injuries that result not only in tremendous physical and emotional pain but also substantial economic impact as well.Case presentation.Three cases of hand injury caused by meat grinders are presented. Two injuries involved non dominant hand and one involved dominant hand, result in varying degrees of deformity. All patients arrived in emergency room with injured hand still firmly...

Multi-axial correction system in the treatment of radial club hand.

Science.gov (United States)

Bhat, Suneel B; Kamath, Atul F; Sehgal, Kriti; Horn, B David; Hosalkar, Harish S

2009-12-01

Radial club hand is a well-recognized congenital malformation characterized by hypoplasia of bone and soft tissue on the radial aspect of the forearm and hand. The modalities of treatment have traditionally varied from stretching casts with soft-tissue procedures to the use of multiple corrective osteotomies. These osteotomies can be stabilized by a variety of methods, including external fixators that allow the possibility of gradual distraction with neohistiogenesis. This current study outlines the usage of one such device (multi-axial correction system [MAC]) in the management of deformity associated with severe radial club hand. Three consecutive cases of unilateral or bilateral severe (Bayne type IV) congenital radial club hand were corrected using MAC fixation in the last 5 years. This is a retrospective review of all three cases. Data parameters included: patient demographics, presentation findings, degree of deformity, amount of correction/lengthening, length of procedure, length of treatment, and associated complications. The surgical technique is described in detail for the benefit of the readership. The three patients with severe congenital radial club hand had a total of four limb involvements that underwent correction using osteotomies and usage of the MAC device for external fixation. All three patients underwent successful correction of deformity with the restoration of alignment, lengthening of forearm for improvement of function, and stabilization of the wrist (mean duration, mean lengthening, mean time to consolidation). The MAC system was well tolerated in all patients and associated complications were limited. The MAC fixator seems to be a good alternative modality of stabilization and correction for severe congenital radial club hand deformities. Its usage is fairly simple and it provides the ease of application of a mono-lateral fixator with far superior three-dimensional control, like the circular external fixator. We recommend that

HAND OSTEOARTHROSIS: ON THE QUALITY OF LIFE AND AESTHETIC DISCOMFORT

Directory of Open Access Journals (Sweden)

Anastasia Viktorovna Sarapulova

2013-01-01

Full Text Available Osteoarthrosis (OA is one of the most common causes of hand pains, leading to lower quality of life (QL. In addition to pain and functional impairment, the patients' aesthetic dissatisfaction that cannot be now determined or measuredis of prime importanceObjective: to assess a number of QL aspects and to measure the level of aesthetic discomfort in patients with hand OA.Subjects and methods. Sixty women aged 45–75 years with hand OA were included. The number of painful and deformed joints was determined and functional impairments were evaluated using the AUSCAN questionnaire. The patients filled out the questionnaire to determine the level of dissatisfaction with the appearance of their hands; the Ellis stress test for irrational beliefs was carried out.Results. The patients with hand OA were found to have significant aesthetic discomfort comparable with level of joint pain. Deformity phobia in the future and external discomfort because of hand deformity were most pronounced; a wish for surgical correction was less pronounced. Comparison of the results obtained in different age groups determined the highest levels of anxiety and wish for surgical correction in younger women. The patients' aesthetic dissatisfaction was also influenced by employment and internet usage.Conclusion. Aesthetic discomfort is an important component of lower QL in patients with hand OA. Further investigation of this factor and elaboration of criteria for its estimation are needed.

Digital fringe projection for hand surface coordinate variation analysis caused by osteoarthritis

Science.gov (United States)

Nor Haimi, Wan Mokhdzani Wan; Hau Tan, Cheek; Retnasamy, Vithyacharan; Vairavan, Rajendaran; Sauli, Zaliman; Roshidah Yusof, Nor; Hambali, Nor Azura Malini Ahmad; Aziz, Muhammad Hafiz Ab; Bakhit, Ahmad Syahir Ahmad

2017-11-01

Hand osteoarthritis is one of the most common forms of arthritis which impact millions of people worldwide. The disabling problem occurs when the protective cartilage on the boundaries of bones wear off over time. Currently, in order to identify hand osteoarthritis, special instruments namely X-ray scanning and MRI are used for the detection but it also has its limitations such as radiation exposure and can be quite costly. In this work, an optical metrology system based on digital fringe projection which comprises of an LCD projector, CCD camera and a personal computer has been developed to anticipate abnormal growth or deformation on the joints of the hand which are common symptoms of osteoarthritis. The main concept of this optical metrology system is to apply structured light as imaging source for surface change detection. The imaging source utilizes fringe patterns generated by C++ programming and is shifted by 3 phase shifts based on the 3 steps 2 shifts method. Phase wrapping technique and analysis were applied in order to detect the deformation of live subjects. The result has demonstrated a successful method of hand deformation detection based on the pixel tracking differences of a normal and deformed state.

A multifaceted hospital-wide intervention increases hand hygiene ...

African Journals Online (AJOL)

Hospital-acquired infections remain a global concern, with prevalence .... precautionary measures such as hand washing. A baseline audit in. 2014 on hand hygiene at GSH reflected an average performance of. 34% for the hospital. ..... hand hygiene intervention based on WHO and continuous improvement methodology.

Pixels Intensity Evolution to Describe the Plastic Films Deformation

Directory of Open Access Journals (Sweden)

Juan C. Briñez-De León

2013-11-01

Full Text Available This work proposes an approach for mechanical behavior description in the plastic film deformation using techniques for the images analysis, which are based on the intensities evolution of fixed pixels applied to an images sequence acquired through polarizing optical assembly implemented around the platform of the plastic film deformation. The pixels intensities evolution graphs, and mechanical behavior graphic of the deformation has dynamic behaviors zones which could be associated together.

Formation of social and household skills in children with hand defects.

Science.gov (United States)

Klimon, Nataly; Koryukov, Alexander; Loseva, Nina; Starobina, Elena

2015-08-01

The aim of this study was to consider the peculiarities of forming social and household skills, and the criteria for their evaluation, as well as an assessment of functional capacity, in children with hand defects both before and after surgical treatment and rehabilitation courses using a system of games. We elaborated and implemented a program of social rehabilitation of preschool children with congenital and acquired hand defects for the development of their functional capabilities and the formation of social and household skills after surgical treatment and prosthetics using play therapy methods. As part of this work, 140 preschool children aged 3-7 years underwent social rehabilitation. Most of the children had congenital hand defects-122 children (87 %): 96 children (79 %) with ectrodactylia, adactylia, hypoplasia, aplasia, hand splitting, club hand, or partial gigantism; 26 children (21 %) with congenital syndactylism and constricted bonds and 18 children (13 %) with acquired defects (burn deformity, amputation). 110 children (79 %) had reached the stage of surgical correction; 30 children (21 %) reached the stage of prosthetics. Most of the children participating in the experiment (78 children, 56 %) had defects of fingers on one hand. The program aimed at solving specific rehabilitation tasks: formation and improvement of all possible types of grip under the existing defect including those after surgery and prosthetics; development of tactile sensations in fingers; development of fine motor skills; increase in range of motion in all joints of the damaged hand; development of attention and concentration; formation of social and household skills appropriate to age; and development of the ability to achieve the set task. Analysis of the level of social and household skills of children with hand defects undergoing rehabilitation treatment at the hospital depending on the age prior to medical and social rehabilitation showed that preschool children with

Nd-Fe-B-Cu hot deformation processing: a comparison of deformation modes, microstructural development and magnetic properties

International Nuclear Information System (INIS)

Ferrante, M.; Sinka, V.; Assis, O.B.G.; Oliveira, I. de; Freitas, E. de

1996-01-01

Due to its relative simplicity and low cost the hot deformation of Nd-Fe-B ingots is rapidly reaching the status of a valid alternative to sintering. Among the possible deformation modes, pressing, rolling and forging are perhaps the most successful. This paper describes the research programme undertaken so far, by discussing the relationship between deformation mode, microstructure and magnetic properties of magnets produced by hot deformation mode, microstructure and magnetic properties of magnets produced by hot deformation of a number of Nd-fe-B-Cu alloys. Microstructural observation showed that both pressed and forged samples are characterized by a heterogeneous microstructure and from magnetic measurements it was concluded that magnetic properties differ when taken in the center or in the periphery of the sample. On the other hand roller magnets were homogeneous both in terms of microstructure and magnetic properties, and interpretations of the mechanisms of texture development and of microstructural development of hot deformed magnets is put forward. (author)

Comparative Outcomes Between Step-Cut Lengthening Calcaneal Osteotomy vs Traditional Evans Osteotomy for Stage IIB Adult-Acquired Flatfoot Deformity.

Science.gov (United States)

Saunders, Stuart M; Ellis, Scott J; Demetracopoulos, Constantine A; Marinescu, Anca; Burkett, Jayme; Deland, Jonathan T

2018-01-01

The forefoot abduction component of the flexible adult-acquired flatfoot can be addressed with lengthening of the anterior process of the calcaneus. We hypothesized that the step-cut lengthening calcaneal osteotomy (SLCO) would decrease the incidence of nonunion, lead to improvement in clinical outcome scores, and have a faster time to healing compared with the traditional Evans osteotomy. We retrospectively reviewed 111 patients (143 total feet: 65 Evans, 78 SLCO) undergoing stage IIB reconstruction followed clinically for at least 2 years. Preoperative and postoperative radiographs were analyzed for the amount of deformity correction. Computed tomography (CT) was used to analyze osteotomy healing. The Foot and Ankle Outcome Scores (FAOS) and lateral pain surveys were used to assess clinical outcomes. Mann-Whitney U tests were used to assess nonnormally distributed data while χ 2 and Fisher exact tests were used to analyze categorical variables (α = 0.05 significant). The Evans group used a larger graft size ( P lengthening. Level III, retrospective cohort study.

Iterative co-creation for improved hand hygiene and aseptic techniques in the operating room: experiences from the safe hands study.

Science.gov (United States)

Erichsen Andersson, Annette; Frödin, Maria; Dellenborg, Lisen; Wallin, Lars; Hök, Jesper; Gillespie, Brigid M; Wikström, Ewa

2018-01-04

Hand hygiene and aseptic techniques are essential preventives in combating hospital-acquired infections. However, implementation of these strategies in the operating room remains suboptimal. There is a paucity of intervention studies providing detailed information on effective methods for change. This study aimed to evaluate the process of implementing a theory-driven knowledge translation program for improved use of hand hygiene and aseptic techniques in the operating room. The study was set in an operating department of a university hospital. The intervention was underpinned by theories on organizational learning, culture and person centeredness. Qualitative process data were collected via participant observations and analyzed using a thematic approach. Doubts that hand-hygiene practices are effective in preventing hospital acquired infections, strong boundaries and distrust between professional groups and a lack of psychological safety were identified as barriers towards change. Facilitated interprofessional dialogue and learning in "safe spaces" worked as mechanisms for motivation and engagement. Allowing for the free expression of different opinions, doubts and viewing resistance as a natural part of any change was effective in engaging all professional categories in co-creation of clinical relevant solutions to improve hand hygiene. Enabling nurses and physicians to think and talk differently about hospital acquired infections and hand hygiene requires a shift from the concept of one-way directed compliance towards change and learning as the result of a participatory and meaning-making process. The present study is a part of the Safe Hands project, and is registered with ClinicalTrials.gov (ID: NCT02983136 ). Date of registration 2016/11/28, retrospectively registered.

High-Efficiency Multiscale Modeling of Cell Deformations in Confined Microenvironments in Microcirculation and Microfluidic Devices

Science.gov (United States)

Lu, Huijie; Peng, Zhangli

2017-11-01

Our goal is to develop a high-efficiency multiscale modeling method to predict the stress and deformation of cells during the interactions with their microenvironments in microcirculation and microfluidic devices, including red blood cells (RBCs) and circulating tumor cells (CTCs). There are more than 1 billion people in the world suffering from RBC diseases, e.g. anemia, sickle cell diseases, and malaria. The mechanical properties of RBCs are changed in these diseases due to molecular structure alternations, which is not only important for understanding the disease pathology but also provides an opportunity for diagnostics. On the other hand, the mechanical properties of cancer cells are also altered compared to healthy cells. This can lead to acquired ability to cross the narrow capillary networks and endothelial gaps, which is crucial for metastasis, the leading cause of cancer mortality. Therefore, it is important to predict the deformation and stress of RBCs and CTCs in microcirculations. We are developing a high-efficiency multiscale model of cell-fluid interaction to study these two topics.

Prevalence of self-reported finger deformations and occupational risk factors among professional cooks: a cross-sectional study.

Science.gov (United States)

Nagasu, Miwako; Sakai, Kazuhiro; Kogi, Kazutaka; Ito, Akiyoshi; Feskens, Edith J M; Tomita, Shigeru; Temmyo, Yoshiomi; Ueno, Mitsuo; Miyagi, Shigeji

2011-05-26

Previous studies have pointed out that the school lunch workers in Japan are suffering from work-related disorders including finger deformations. The purpose of this study was to investigate the prevalence of self-reported finger deformations and the association with job-related risk factors. A cross-sectional questionnaire study of 5,719 subjects (response rate: 81%, 982 men and 4,737 women) was undertaken during September 2003 to February 2004. Finger deformations were found among 11.7% of the men and 35.6% of the women studied, with significant differences among sex, age and sex-age groups. For both men and women the pattern of finger deformations across the hand was similar for the right and the left hand. For women, the deformations were found in about 10% of the distal interphalangeal joints of all fingers. Based on multiple logistic regression analyses, the factors female sex, age, the number of cooked lunches per cook and cooking activities were independently associated with the prevalence of finger deformations. High prevalence odds ratios were found for those frequently carrying or using tools by hands such as delivering containers, distributing meals, preparing dishes, washing equipment, cutting and stirring foods. Among the school lunch workers studied, women had a higher prevalence of finger deformations on all joints of both hands. Various cooking tasks were associated with the prevalence of finger deformations. The results suggest that improvements in working conditions are important for preventing work-related disorders such as finger deformations.

Plasticity margin recovery during annealing after cold deformation

International Nuclear Information System (INIS)

Bogatov, A.A.; Smirnov, S.V.; Kolmogorov, V.L.

1978-01-01

Restoration of the plasticity margin in steel 20 after cold deformation and annealing at 550 - 750 C and soaking for 5 - 300 min was investigated. The conditions of cold deformation under which the metal acquires microdefects unhealed by subsequent annealing were determined. It was established that if the degree of utilization of the plasticity margin is psi < 0.5, the plasticity margin in steel 20 can be completely restored by annealing. A mathematical model of restoration of the plasticity margin by annealing after cold deformation was constructed. A statistical analysis showed good agreement between model and experiment

Evaluation of antibacterial efficacy of some alcohol-based Hand ...

African Journals Online (AJOL)

Hospital and community-acquired infections are a serious problem worldwide often leading to increased deaths, costs and other problems. Hand hygiene has been promoted as the most important way to prevent these infections. The use of hand sanitizers is one of the ways to address the barriers to effective hand hygiene.

Hindfoot Arthrodesis for Neuropathic Deformity

Directory of Open Access Journals (Sweden)

Peng-Ju Huang

2007-03-01

Full Text Available Acquired neurologic disorders of the foot lead to arthrosis, deformities, instabilities, and functional disabilities. Hindfoot arthrodesis is the current option available for irreducible or nonbraceable deformities of neuropathic feet. However, the role of ankle arthrodesis in these patients has been questioned because of high nonunion and complication rates. From 1990 to 2001, 17 cases of acquired neuropathic foot deformities were treated by four tibiotalocalcaneal (TTC arthrodeses and 13 ankle arthrodeses. TTC arthrodesis was performed on cases with combined ankle and subtalar arthritis or cases whose deformities or instabilities could not be corrected by ankle fusion alone. There was no nonunion of TTC arthrodesis and seven ununited ankle arthrodeses were salvaged by two TTC-attempted arthrodeses and five revision ankle-attempted arthrodeses. Eventually in these cases, there was one nonunion in TTC arthrodesis and one nonunion in revision ankle arthrodesis. The final fusion rate was 88% (15 of 17 cases with average union time of 6.9 months (range, 2.5–18 months. The American Orthopaedic Foot and Ankle Society ankle hind-foot functional scores were evaluated: one was excellent (5.8%, seven were good (41%, eight were fair (53.3%, and one was poor (5.8% in terms of total functional outcome. We conclude that TTC arthrodesis is indicated for cases with ankle and subtalar involvement and ankle arthrodesis is an alternative for cases with intact subtalar joint. We recommend revision ankle arthrodesis if the ankle fails to fuse and the bone stock of the talus is adequate. TTC arthrodesis is reserved for ankles with poor bone stock of the talus with fragmentation.

Validation of the Foot and Ankle Outcome Score in adult acquired flatfoot deformity.

Science.gov (United States)

Mani, Sriniwasan B; Brown, Haydée C; Nair, Pallavi; Chen, Lan; Do, Huong T; Lyman, Stephen; Deland, Jonathan T; Ellis, Scott J

2013-08-01

The American Orthopaedic Foot and Ankle Society (AOFAS) Ankle-Hindfoot Score has been under recent scrutiny. The Foot and Ankle Outcome Score (FAOS) is an alternative subjective survey, assessing outcomes in 5 subscales. It is validated for lateral ankle instability and hallux valgus patients. The aim of our study was to validate the FAOS for assessing outcomes in flexible adult acquired flatfoot deformity (AAFD). Patients from the authors' institution diagnosed with flexible AAFD from 2006 to 2011 were eligible for the study. In all, 126 patients who completed the FAOS and the Short-Form 12 (SF-12) on the same visit were included in the construct validity component. Correlation was deemed moderate if the Spearman's correlation coefficient was .4 to .7. Content validity was assessed in 63 patients by a questionnaire that asked patients to rate the relevance of each FAOS question, with a score of 2 or greater considered acceptable. Reliability was measured using intraclass correlation coefficients (ICCs) in 41 patients who completed a second FAOS survey. In 49 patients, preoperative and postoperative FAOS scores were compared to determine responsiveness. All of the FAOS subscales demonstrated moderate correlation with 2 physical health related SF-12 domains. Mental health related domains showed poor correlation. Content validity was high for the Quality of Life (QoL; mean 2.26) and Sports/Recreation subscales (mean 2.12). All subscales exhibited very good test-retest reliability, with ICCs of .7 and above. Symptoms, QoL, pain, and daily activities (ADLs) were responsive to change in postoperative patients (P validated the FAOS for AAFD with acceptable construct and content validity, reliability, and responsiveness. Given its previous validation for patients with ankle instability and hallux valgus, the additional findings in this study support its use as an alternative to less reliable outcome surveys. Level II, prospective comparative study.

Hand Washing Practices and Compliance among Health Care ...

African Journals Online (AJOL)

Hand washing is the simplest, most inexpensive and most effective method of reducing the incidence of hospital-acquired infections in the Intensive Care Unit. Several reports have shown a relationship between improved hand washing practices and reduced infection rates. We conducted a prospective, ...

The swimming of a perfect deforming helix

Science.gov (United States)

Koens, Lyndon; Zhang, Hang; Mourran, Ahmed; Lauga, Eric

2017-11-01

Many bacteria rotate helical flagellar filaments in order to swim. When at rest or rotated counter-clockwise these flagella are left handed helices but they undergo polymorphic transformations to right-handed helices when the motor is reversed. These helical deformations themselves can generate motion, with for example Rhodobacter sphaeroides using the polymorphic transformation of the flagellum to generate rotation, or Spiroplasma propagating a change of helix handedness across its body's length to generate forward motion. Recent experiments reported on an artificial helical microswimmer generating motion without a propagating change in handedness. Made of a temperature sensitive gel, these swimmers moved by changing the dimensions of the helix in a non-reciprocal way. Inspired by these results and helix's ubiquitous presence in the bacterial world, we investigate how a deforming helix moves within a viscous fluid. Maintaining a single handedness along its entire length, we discuss how a perfect deforming helix can create a non-reciprocal swimming stroke, identify its principle directions of motion, and calculate the swimming kinematics asymptotically.

Helping hands: A cluster randomised trial to evaluate the effectiveness of two different strategies for promoting hand hygiene in hospital nurses

NARCIS (Netherlands)

Huis, A.M.P.; Schoonhoven, L.; Grol, R.P.T.M.; Borm, G.F.; Adang, E.M.M.; Hulscher, M.E.J.L.; Achterberg, T. van

2011-01-01

ABSTRACT: BACKGROUND: Hand hygiene prescriptions are the most important measure in the prevention of hospital-acquired infections. Yet, compliance rates are generally below 50% of all opportunities for hand hygiene. This study aims at evaluating the short- and long-term effects of two different

The Free-Hand Technique for S2-Alar-Iliac Screw Placement: A Safe and Effective Method for Sacropelvic Fixation in Adult Spinal Deformity.

Science.gov (United States)

Shillingford, Jamal N; Laratta, Joseph L; Tan, Lee A; Sarpong, Nana O; Lin, James D; Fischer, Charla R; Lehman, Ronald A; Kim, Yongjung J; Lenke, Lawrence G

2018-02-21

Spinopelvic fixation is an integral part of achieving solid fusion across the lumbosacral junction, especially in deformity procedures requiring substantial correction or long-segment constructs. Traditional S2-alar-iliac (S2AI) screw-placement techniques utilize fluoroscopy, increasing operative time and radiation exposure to the patient and surgeon. We describe a novel free-hand technique for S2AI screw placement in patients with adult spinal deformity. We reviewed the records of 45 consecutive patients who underwent spinopelvic fixation performed with use of S2AI screws by the senior surgeon and various fellows or residents over a 12-month period (2015 to 2016). In each case, the S2AI screws were placed utilizing a free-hand technique without fluoroscopic or image guidance. Screw position and accuracy were assessed by intraoperative O-arm imaging and analyzed using 3-dimensional interactive manipulation of computed tomography images. A total of 100 screws were placed, 51 by the senior surgeon and 49 by trainees. The mean patient age was 57.4 ± 12.7 years at the time of surgery; 37 (82.2%) of the patients were female. Preoperative diagnoses included adult idiopathic scoliosis (n = 19), adult degenerative scoliosis (n = 15), flatback syndrome (n = 2), fixed sagittal imbalance (n = 6), and distal junctional kyphosis (n = 3). Five (5%) of the screws were placed with moderate to severe cortical breaches, all of which perforated the pelvis posteriorly, with no clinically notable neurovascular or visceral complications. The breach rate did not differ significantly between the senior surgeon and trainees. The free-hand technique for S2AI screw placement, when performed in a standardized manner, was demonstrated to be safe and reliable in constructs requiring spinopelvic fixation. The accuracy of screw placement relies on visible and palpable anatomic landmarks that obviate the need for intraoperative fluoroscopy or image guidance, potentially reducing operative time

Contactless and pose invariant biometric identification using hand surface.

Science.gov (United States)

Kanhangad, Vivek; Kumar, Ajay; Zhang, David

2011-05-01

This paper presents a novel approach for hand matching that achieves significantly improved performance even in the presence of large hand pose variations. The proposed method utilizes a 3-D digitizer to simultaneously acquire intensity and range images of the user's hand presented to the system in an arbitrary pose. The approach involves determination of the orientation of the hand in 3-D space followed by pose normalization of the acquired 3-D and 2-D hand images. Multimodal (2-D as well as 3-D) palmprint and hand geometry features, which are simultaneously extracted from the user's pose normalized textured 3-D hand, are used for matching. Individual matching scores are then combined using a new dynamic fusion strategy. Our experimental results on the database of 114 subjects with significant pose variations yielded encouraging results. Consistent (across various hand features considered) performance improvement achieved with the pose correction demonstrates the usefulness of the proposed approach for hand based biometric systems with unconstrained and contact-free imaging. The experimental results also suggest that the dynamic fusion approach employed in this work helps to achieve performance improvement of 60% (in terms of EER) over the case when matching scores are combined using the weighted sum rule.

Prevalence of self-reported finger deformations and occupational risk factors among professional cooks: a cross-sectional study

Directory of Open Access Journals (Sweden)

Tomita Shigeru

2011-05-01

Full Text Available Abstract Background Previous studies have pointed out that the school lunch workers in Japan are suffering from work-related disorders including finger deformations. The purpose of this study was to investigate the prevalence of self-reported finger deformations and the association with job-related risk factors. Methods A cross-sectional questionnaire study of 5,719 subjects (response rate: 81%, 982 men and 4,737 women was undertaken during September 2003 to February 2004. Results Finger deformations were found among 11.7% of the men and 35.6% of the women studied, with significant differences among sex, age and sex-age groups. For both men and women the pattern of finger deformations across the hand was similar for the right and the left hand. For women, the deformations were found in about 10% of the distal interphalangeal joints of all fingers. Based on multiple logistic regression analyses, the factors female sex, age, the number of cooked lunches per cook and cooking activities were independently associated with the prevalence of finger deformations. High prevalence odds ratios were found for those frequently carrying or using tools by hands such as delivering containers, distributing meals, preparing dishes, washing equipment, cutting and stirring foods. Conclusions Among the school lunch workers studied, women had a higher prevalence of finger deformations on all joints of both hands. Various cooking tasks were associated with the prevalence of finger deformations. The results suggest that improvements in working conditions are important for preventing work-related disorders such as finger deformations.

Integration of breathing in radiotherapy: contribution of the image deformable registration

International Nuclear Information System (INIS)

Boldea, Vlad

2006-01-01

As taking organ movements and deformations into account in radiotherapy for the treatment of lung cancer is a challenge as it allows the delivered dose to be increased while better sparing surrounding sane tissues, this research thesis addresses non-rigid (or deformable) registration iconic methods applied to thorax X ray computed tomography (X-ray CT) 3D acquisitions. The objective is to extract the information regarding lung and tumour movement and deformation. The author thus reports the development of deformable registration framework with several methods of regularisation of vector fields. Three main studies have been performed and are reported. In the first one, deformable registration allowed the breathe blockage reproducibility to be controlled. Experiments performed on ten patients showed that this blockage is efficient (displacement less than 5 mm), except for three of them with functional anomalies. In a second study, 4D X-ray CT acquisitions (3D X-ray CT images acquired at different moments of the normal breathing cycle) have been analysed to extract and follow thorax movements and deformations in order to take them into account in free breathing and to perform 4D dynamic dosimetric studies. A first 4D X-ray CT image model has been developed from 3D X-ray CT images acquired in breathe blockage at the end of expiration and at the end on inhalation [fr

Measurement of Rotorcraft Blade Deformation Using Projection Moiré Interferometry

Directory of Open Access Journals (Sweden)

Gary A. Fleming

2000-01-01

Full Text Available Projection Moiré Interferometry (PMI has been used to obtain near instantaneous, quantitative blade deformation measurements of a generic rotorcraft model at several test conditions. These laser-based measurements provide quantitative, whole field, dynamic blade deformation profiles conditionally sampled as a function of rotor azimuth. The instantaneous nature of the measurements permits computation of the mean and unsteady blade deformation, blade bending, and twist. The PMI method is presented, and the image processing steps required to obtain quantitative deformation profiles from PMI interferograms are described. Experimental results are provided which show blade bending, twist, and unsteady motion. This initial proof-of-concept test has demonstrated the capability of PMI to acquire accurate, full field rotorcraft blade deformation data.

Back to basics: hand hygiene and isolation

Science.gov (United States)

Lin Huang, G. Khai; Stewardson, Andrew J.; Lindsay Grayson, M.

2014-01-01

Purpose of review Hand hygiene and isolation are basic, but very effective, means of preventing the spread of pathogens in healthcare. Although the principle may be straightforward, this review highlights some of the controversies regarding the implementation and efficacy of these interventions. Recent findings Hand hygiene compliance is an accepted measure of quality and safety in many countries. The evidence for the efficacy of hand hygiene in directly reducing rates of hospital-acquired infections has strengthened in recent years, particularly in terms of reduced rates of staphylococcal sepsis. Defining the key components of effective implementation strategies and the ideal method(s) of assessing hand hygiene compliance are dependent on a range of factors associated with the healthcare system. Although patient isolation continues to be an important strategy, particularly in outbreaks, it also has some limitations and can be associated with negative effects. Recent detailed molecular epidemiology studies of key healthcare-acquired pathogens have questioned the true efficacy of isolation, alone as an effective method for the routine prevention of disease transmission. Summary Hand hygiene and isolation are key components of basic infection control. Recent insights into the benefits, limitations and even adverse effects of these interventions are important for their optimal implementation. PMID:24945613

Diagnostic imaging of the hand. 3. rev. and enl. ed.; Bildgebende Diagnostik der Hand

Energy Technology Data Exchange (ETDEWEB)

Schmitt, Rainer [Herz und Gefaessklinik GmbH, Bad Neustadt (Germany). Klinik fuer Diagnostische und Interventionelle Radiologie; Lanz, Ulrich

2015-07-01

The book on diagnostic imaging of the hand covers the following issues: projection radiography, cinematography, MRT and CR arthrography, arthroscopy, arteriography, skeleton scintiscanning, sonography, computerized tomography, magnetic resonance tomography, anatomy of forearm and carpus, anatomy of metacarpus and fingers, carpal function and morphometry, postoperative X-ray diagnostic, growing hand skeleton, normative variants, malformations and deformities, trauma of the distal forearm, lesions of the ulnocarpal complex (TFCC), scaphoid fractures, scaphoid arthrosis, fractures of other carpus bones, carpal luxations and luxation fractures, carpal instabilities, fractures of the metacarpalla, finger fractures, arthrosis deformans, enthesiopathies, sport induced soft tissue lesions, osteonecrosis, impingement syndromes, osteopenic skeletal diseases, metabolis diseases, crystal-induced osteoarthropaties, rheumatoid arthritis, spondyloarthritis, rheumatic fever, collagenoses, infective arthritis, osteomyelitis, soft tissue infections, cystoids bone lesions, skeletal tumors, soft tissue tumors, carpal tunnel syndrome, nerve compression syndrome, arterial perfusion disturbances, differential diagnostic tables on hand lesions.

Using postural synergies to animate a low-dimensional hand avatar in haptic simulation.

Science.gov (United States)

Mulatto, Sara; Formaglio, Alessandro; Malvezzi, Monica; Prattichizzo, Domenico

2013-01-01

A technique to animate a realistic hand avatar with 20 DoFs based on the biomechanics of the human hand is presented. The animation does not use any sensor glove or advanced tracker with markers. The proposed approach is based on the knowledge of a set of kinematic constraints on the model of the hand, referred to as postural synergies, which allows to represent the hand posture using a number of variables lower than the number of joints of the hand model. This low-dimensional set of parameters is estimated from direct measurement of the motion of thumb and index finger tracked using two haptic devices. A kinematic inversion algorithm has been developed, which takes synergies into account and estimates the kinematic configuration of the whole hand, i.e., also of the fingers whose end tips are not directly tracked by the two haptic devices. The hand skin is deformable and its deformation is computed using a linear vertex blending technique. The proposed synergy-based animation of the hand avatar involves only algebraic computations and is suitable for real-time implementation as required in haptics.

Hand hygiene noncompliance and the cost of hospital-acquired methicillin-resistant Staphylococcus aureus infection.

Science.gov (United States)

Cummings, Keith L; Anderson, Deverick J; Kaye, Keith S

2010-04-01

Hand hygiene noncompliance is a major cause of nosocomial infection. Nosocomial infection cost data exist, but the effect of hand hygiene noncompliance is unknown. To estimate methicillin-resistant Staphylococcus aureus (MRSA)-related cost of an incident of hand hygiene noncompliance by a healthcare worker during patient care. Two models were created to simulate sequential patient contacts by a hand hygiene-noncompliant healthcare worker. Model 1 involved encounters with patients of unknown MRSA status. Model 2 involved an encounter with an MRSA-colonized patient followed by an encounter with a patient of unknown MRSA status. The probability of new MRSA infection for the second patient was calculated using published data. A simulation of 1 million noncompliant events was performed. Total costs of resulting infections were aggregated and amortized over all events. Duke University Medical Center, a 750-bed tertiary medical center in Durham, North Carolina. Model 1 was associated with 42 MRSA infections (infection rate, 0.0042%). Mean infection cost was $47,092 (95% confidence interval [CI], $26,040-$68,146); mean cost per noncompliant event was $1.98 (95% CI, $0.91-$3.04). Model 2 was associated with 980 MRSA infections (0.098%). Mean infection cost was $53,598 (95% CI, $50,098-$57,097); mean cost per noncompliant event was $52.53 (95% CI, $47.73-$57.32). A 200-bed hospital incurs $1,779,283 in annual MRSA infection-related expenses attributable to hand hygiene noncompliance. A 1.0% increase in hand hygiene compliance resulted in annual savings of $39,650 to a 200-bed hospital. Hand hygiene noncompliance is associated with significant attributable hospital costs. Minimal improvements in compliance lead to substantial savings.

Variable Operative Experience in Hand Surgery for Plastic Surgery Residents.

Science.gov (United States)

Silvestre, Jason; Lin, Ines C; Levin, Lawrence Scott; Chang, Benjamin

Efforts to standardize hand surgery training during plastic surgery residency remain challenging. We analyze the variability of operative hand experience at U.S. plastic surgery residency programs. Operative case logs of chief residents in accredited U.S. plastic surgery residency programs were analyzed (2011-2015). Trends in fold differences of hand surgery case volume between the 10th and 90th percentiles of residents were assessed graphically. Percentile data were used to calculate the number of residents achieving case minimums in hand surgery for 2015. Case logs from 818 plastic surgery residents were analyzed of which a minority were from integrated (35.7%) versus independent/combined (64.3%) residents. Trend analysis of fold differences in case volume demonstrated decreasing variability among procedure categories over time. By 2015, fold differences for hand reconstruction, tendon cases, nerve cases, arthroplasty/arthrodesis, amputation, arterial repair, Dupuytren release, and neoplasm cases were below 10-fold. Congenital deformity cases among independent/combined residents was the sole category that exceeded 10-fold by 2015. Percentile data suggested that approximately 10% of independent/combined residents did not meet case minimums for arterial repair and congenital deformity in 2015. Variable operative experience during plastic surgery residency may limit adequate exposure to hand surgery for certain residents. Future studies should establish empiric case minimums for plastic surgery residents to ensure hand surgery competency upon graduation. Copyright © 2017 Association of Program Directors in Surgery. Published by Elsevier Inc. All rights reserved.

Correction of severe postburn claw hand.

Science.gov (United States)

Davami, Babak; Pourkhameneh, Golnar

2011-12-01

Burn scar contractures are perhaps the most frequent and most frustrating sequelae of thermal injuries to the hand. Unfortunately, stiffness occurs in the burned hand quickly. A week of neglect in the burned hand can lead to digital malpositioning and distortion that may be difficult to correct. The dorsal contracture is the most common of all the complications of the burned hand. It is the result of damage to the thin dorsal skin and scant subcutaneous tissue, which offers little protection to the deeper structures. Consequently, these injuries are deep resulting in a spectrum of deformities that has remained the bane of reconstructive surgery. Flap coverage will be required in the event of exposure of joints and tendons with absent paratenons. Multiple different flap types are available to treat complex severe postburn hand contractures. In our center, which is the largest regional burn center in northwest Iran, we have considerable experience in the treatment of thermal hand injuries. Between 2005 and 2010, we treated 53 consecutive patients with 65 severe postburn hand deformities. There were 35 men and 18 women with a mean age of 35±3 years. Flame injury was the inciting traumatic event in each patient. The severity of original injury and inadequate early treatment resulted in all of the fingers developing a severe extension contracture with scarred and adherent extensor tendons and subluxed metacarpophalangeal joints. In 36 cases, the injury was in the patients' dominant hand. We first incised the dorsal aspect of the contracted hands where there was maximum tension, then tenolysed the extensor tendons and released the volar capsules, collateral ligaments, and volar plate in all cases. In 30 cases, we also tenolysed the flexor tendons. We reduced the subluxed metacarpophalangeal joints and fixed them with Kirschner wires in 70 to 90 degrees flexion. Then, we planned and performed axial groin flaps to reconstruct the defects in all of them. In all of these

T\\overline{T} -deformations, AdS/CFT and correlation functions

Science.gov (United States)

Giribet, Gaston

2018-02-01

A solvable irrelevant deformation of AdS3/CFT2 correspondence leading to a theory with Hagedorn spectrum at high energy has been recently proposed. It consists of a single trace deformation of the boundary theory, which is inspired by the recent work on solvable T\\overline{T} deformations of two-dimensional CFTs. Thought of as a worldsheet σ-model, the interpretation of the deformed theory from the bulk viewpoint is that of string theory on a background that interpolates between AdS3 in the IR and a linear dilaton vacuum of little string theory in the UV. The insertion of the operator that realizes the deformation in the correlation functions produces a logarithmic divergence, leading to the renormalization of the primary operators, which thus acquire an anomalous dimension. We compute this anomalous dimension explicitly, and this provides us with a direct way of determining the spectrum of the theory. We discuss this and other features of the correlation functions in presence of the deformation.

The use of expanded polytetrafluoroethylene in depressed deformities of the face.

Science.gov (United States)

Liu, Xiaowei; Zhang, Yiming; Wang, Shaoliang; Lei, Zeyuan; Li, Xiang; Fan, Dongli

2016-11-01

Expanded polytetrafluoroethylene (ePTFE) has been extensively used for facial soft tissue augmentation procedures, and is regarded as safe and reliable and suitable as a permanent implant. This implant is generally used in the lower third of the face for lips filling, nasal augmentation, nasolabial folds and chin augmentation, and rarely for congenital or acquired depressed deformities of the face. The aim of the present study was to assess the effects of ePTFE in congenital or acquired depressed deformities of the face. From September, 2008 to January, 2014, 26 patients were implanted with the material ePTFE to correct depressed deformities of the face. The average age at operation was 23.2 years, with a range of 17-45 years. The depressed deformities were lateralized. The follow-up period was 6-18 months (average 9 months). The etiologies of the depressed deformities included stable hemifacial atrophy (3 cases), craniofacial microsomia (13 cases), bony depression after trauma (8 cases), and other unclear reasons (2 cases). The operations were performed under local anesthesia. ePTFE was inserted in different tissue planes that varied among the different subanatomical areas in the face: beneath the superficial temporal fascia in the temporal area, and on the surface of the superficial musculoaponeurotic system in the zygomatic area, cheek and mandibular area. All of the patients were followed up. Most of the patients [25 of 26 patients (96.2%)] were satisfied with the results, while 1 patient (3.8%) was not satisfied for incomplete correction of the depressed deformity. In conclusion, aside from lipofilling and a free flap transfer, the results showed that ePTFE was an alternative treatment for facial depressed deformity.

Congenital hand anomalies in Upper Egypt

Directory of Open Access Journals (Sweden)

Tarek Abulezz

2016-01-01

Full Text Available Background: Congenital hand anomalies are numerous and markedly variant. Their significance is attributed to the frequent occurrence and their serious social, psychological and functional impacts on patient's life. Patients and Methods: This is a follow-up study of 64 patients with hand anomalies of variable severity. All patients were presented to Plastic Surgery Department of Sohag University Hospital in a period of 24 months. Results: This study revealed that failure of differentiation and duplication deformities were the most frequent, with polydactyly was the most common anomaly encountered. The mean age of presentation was 6 years and female to male ratio was 1.46:1. Hand anomalies were either isolated, associated with other anomalies or part of a syndrome. Conclusion: Incidence of congenital hand anomalies in Upper Egypt is difficult to be estimated due to social and cultural concepts, lack of education, poor registration and deficient medical survey. Management of hand anomalies should be individualised, carefully planned and started as early as possible to achieve the best outcome.

[Which foot deformities should be radiologist be familiar with?

Science.gov (United States)

von Stillfried, E

2018-05-01

Most deformities of the foot are visible at birth and can be diagnosed without imaging. They can be divided into congenital flexible, congenital structural and acquired foot deformities. The most common congenital flexible foot deformity in children is the metatarsus adductus, which usually requires no long-term therapy. Regarding congenital structural deformities, such as the clubfoot and talus verticalis, plaster therapy should be started during the first week of life, so that by the end of the first year of life and the beginning of the verticalization, a pain-free resilient foot with normal function is present. Imaging is usually only necessary if a relapse arises. Coalitio of the tarsal bones is often visible only in the course of growth through the development of a rigid flatfoot and always requires imaging to confirm the diagnosis. This article is intended to give the radiologist an overview of the most important deformities and to inform about their course and therapy.

Cytomegalovirus Survival and Transferability and the Effectiveness of Common Hand-Washing Agents against Cytomegalovirus on Live Human Hands

OpenAIRE

Stowell, Jennifer D.; Forlin-Passoni, Daniela; Radford, Kay; Bate, Sheri L.; Dollard, Sheila C.; Bialek, Stephanie R.; Cannon, Michael J.; Schmid, D. Scott

2014-01-01

Congenital cytomegalovirus (CMV) transmission can occur when women acquire CMV while pregnant. Infection control guidelines may reduce risk for transmission. We studied the duration of CMV survival after application of bacteria to the hands and after transfer from the hands to surfaces and the effectiveness of cleansing with water, regular and antibacterial soaps, sanitizer, and diaper wipes. Experiments used CMV AD169 in saliva at initial titers of 1 × 105 infectious particles/ml. Samples fr...

[Acquired disorders of color vision].

Science.gov (United States)

Lascu, Lidia; Balaş, Mihaela

2002-01-01

This article is a general view of acquired disorders of color vision. The revision of the best known methods and of the etiopathogenic classification is not very important in ophthalmology but on the other hand, the detection of the blue defect advertise and associated ocular pathology. There is a major interest in serious diseases as multiple sclerosis, AIDS, diabetes melitus, when the first ocular sign can be a defect in the color vision.

3D palmprint and hand imaging system based on full-field composite color sinusoidal fringe projection technique.

Science.gov (United States)

Zhang, Zonghua; Huang, Shujun; Xu, Yongjia; Chen, Chao; Zhao, Yan; Gao, Nan; Xiao, Yanjun

2013-09-01

Palmprint and hand shape, as two kinds of important biometric characteristics, have been widely studied and applied to human identity recognition. The existing research is based mainly on 2D images, which lose the third-dimensional information. The biological features extracted from 2D images are distorted by pressure and rolling, so the subsequent feature matching and recognition are inaccurate. This paper presents a method to acquire accurate 3D shapes of palmprint and hand by projecting full-field composite color sinusoidal fringe patterns and the corresponding color texture information. A 3D imaging system is designed to capture and process the full-field composite color fringe patterns on hand surface. Composite color fringe patterns having the optimum three fringe numbers are generated by software and projected onto the surface of human hand by a digital light processing projector. From another viewpoint, a color CCD camera captures the deformed fringe patterns and saves them for postprocessing. After compensating for the cross talk and chromatic aberration between color channels, three fringe patterns are extracted from three color channels of a captured composite color image. Wrapped phase information can be calculated from the sinusoidal fringe patterns with high precision. At the same time, the absolute phase of each pixel is determined by the optimum three-fringe selection method. After building up the relationship between absolute phase map and 3D shape data, the 3D palmprint and hand are obtained. Color texture information can be directly captured or demodulated from the captured composite fringe pattern images. Experimental results show that the proposed method and system can yield accurate 3D shape and color texture information of the palmprint and hand shape.

Sports Injury-Related Fingers and Thumb Deformity Due to Tendon or Ligament Rupture.

Science.gov (United States)

Bai, Rong-Jie; Zhang, Hui-Bo; Zhan, Hui-Li; Qian, Zhan-Hua; Wang, Nai-Li; Liu, Yue; Li, Wen-Ting; Yin, Yu-Ming

2018-05-05

Hand injuries are very common in sports, such as skiing and ball sports. One of the major reasons causing hand and finger deformity is due to ligament and tendon injury. The aim of this study was to investigate if the high-resolution 3T magnetic resonance imaging (MRI) can demonstrate the complex anatomy of the fingers and thumb, especially the tendons and ligaments, and provide the accurate diagnosis of clinically important fingers and thumbs deformity due to ligamentous and tendinous injuries during sport activities. Sixteen fresh un-embalmed cadaveric hands were harvested from eight cadavers. A total of 20 healthy volunteers' hands and 44 patients with fingers or thumb deformity due to sports-related injuries were included in this study. All subjects had MR examination with T1-weighted images and proton density-weighted imaging with fat suppression (PD FS) in axial, coronal, and sagittal plane, respectively. Subsequently, all 16 cadaveric hands were sliced into 2-mm thick slab with a band saw (six in coronal plane, six in sagittal plane, and four in axial plane). The correlation of anatomic sections and the MRI characteristics of tendons of fingers and the ulnar collateral ligament (UCL) at the metacarpal phalangeal joint (MCPJ) of thumb between 20 healthy volunteers and 44 patients (confirmed by surgery) were analyzed. The normal ligaments and tendons in 16 cadaveric hands and 20 volunteers' hands showed uniform low-signal intensity on all the sequences of the MRI. Among 44 patients with tendinous and ligamentous injuries in the fingers or thumb, 12 cases with UCL injury at MCPJ of the thumb (Stener lesion = 8 and non-Stener lesion = 4), 6 cases with the central slip injury, 12 cases with terminal tendon injury, and 14 cases with flexor digitorum profundus injury. The ligaments and tendons disruption manifested as increased signal intensity and poor definition, discontinuity, and heterogeneous signal intensity of the involved ligaments and tendons. Sports

High-Resolution Reciprocal Space Mapping for Characterizing Deformation Structures

DEFF Research Database (Denmark)

Pantleon, Wolfgang; Wejdemann, Christian; Jakobsen, Bo

2014-01-01

With high-angular resolution three-dimensional X-ray diffraction (3DXRD), quantitative information is gained about dislocation structures in individual grains in the bulk of a macroscopic specimen by acquiring reciprocal space maps. In high-resolution 3D reciprocal space maps of tensile......-deformed copper, individual, almost dislocation-free subgrains are identified from high-intensity peaks and distinguished by their unique combination of orientation and elastic strain; dislocation walls manifest themselves as a smooth cloud of lower intensity. The elastic strain shows only minor variations within...... dynamics is followed in situ during varying loading conditions by reciprocal space mapping: during uninterrupted tensile deformation, formation of subgrains is observed concurrently with broadening of Bragg reflections shortly after the onset of plastic deformation. When the traction is terminated, stress...

Effect of Prior Deformation on Welding Microstructure of Steel 304L

Directory of Open Access Journals (Sweden)

WU Luo-fei

2017-01-01

Full Text Available This subject was raised by an automotive company.Based on the welding design on the curved surface,the effect of prior deformation on the weld structure was studied.Metal active-gas welding was used on the T-joint and pre-deformed plates of austenitic stainless steel 304L to find the proper welding parameters and observe the effect of prior deformation on the microstructure.The proper parameters acquired are:the speed of the torch is 4mm/s,the speed of delivery of welding wire is 2.5m/min and the voltage is 17V.In the T-joint and pre-deformed joint,the weld toes are in the zone with strain of 0% and 30%.In the pre-deformed welding specimen,it was observed that the fusion zone and partially melted zone are narrowed,carbide precipitation and ferrites are found less.In all,the microstructure in the pre-deformed weld joints on 304L is more uniform.

The effect of hand hygiene compliance on hospital-acquired infections in an ICU setting in a Kuwaiti teaching hospital.

Science.gov (United States)

Salama, Mona F; Jamal, Wafaa Y; Mousa, Haifa Al; Al-Abdulghani, Khaled A; Rotimi, Vincent O

2013-02-01

Hand washing is widely accepted as the cornerstone of infection control in the intensive care unit (ICU). Nosocomial infections are frequently viewed as indicating poor compliance with hand washing guidelines. To determine the hand hygiene (HH) compliance rate among healthcare workers (HCWs) and its effect on the nosocomial infection rates in the ICU of our hospital, we conducted an interventional study. The study spanned a period of 7 months (February 2011-August 2011) and consisted of education about HH indications and techniques, workplace reminder posters, focused group sessions, and feedback on the HH compliance and infection rates. The WHO HH observation protocol was used both before and after a hospital-wide HH campaign directed at all staff members, particularly those in the ICU. Compliance was measured by direct observation of the HCWs, using observation record forms in a patient-directed manner, with no more than two patients observed simultaneously. The overall HH compliance rate was calculated by dividing the number of HH actions by the total number of HH opportunities. The nosocomial infection rates for the pre- and post-interventional periods were also compared to establish the effect of the intervention on rate of infections acquired within the unit. The overall rate of HH compliance by all the HCWs increased from 42.9% pre-intervention to 61.4% post-intervention, P<0.001. Individually, the compliance was highest among the nurses, 49.9 vs. 82.5%, respectively (P<0.001) and lowest among the doctors, 38.6 vs. 43.2%, respectively (P=0.24). The effect of the increase in the HH compliance rate on the nosocomial infection rate was remarkable. There were significant reductions in the following: the rate of overall health care-associated infections/1000 patient-days, which fell from 37.2 pre-intervention to 15.1 post-intervention (P<0.001); the rate of bloodstream infections, which fell from 18.6 to 3.4/1000 central-line-days (P<0.001); and the rate of lower

Direct aperture deformation: An interfraction image guidance strategy

International Nuclear Information System (INIS)

Feng Yuanming; Castro-Pareja, Carlos; Shekhar, Raj; Yu, Cedric

2006-01-01

A new scheme, called direct aperture deformation (DAD), for online correction of interfraction geometric uncertainties under volumetric imaging guidance is presented. Using deformable image registration, the three-dimensional geometric transformation matrix can be derived that associates the planning image set and the images acquired on the day of treatment. Rather than replanning or moving the patient, we use the deformation matrix to morph the treatment apertures as a potential online correction method. A proof-of-principle study using an intensity-modulated radiation therapy plan for a prostate cancer patient was conducted. The method, procedure, and algorithm of DAD are described. The dose-volume histograms from the original plan, reoptimized plan, and rigid-body translation plan are compared with the ones from the DAD plan. The study showed the feasibility of the DAD as a general method for both target dislocation and deformation. As compared with using couch translation to move the patient, DAD is capable of correcting both target dislocation and deformations. As compared with reoptimization, online correction using the DAD scheme could be completed within a few minutes rather than tens of minutes and the speed gain would be at a very small cost of plan quality

Cognitive Achievement and Motivation in Hands-on and Teacher-Centred Science Classes: Does an additional hands-on consolidation phase (concept mapping) optimise cognitive learning at work stations?

Science.gov (United States)

Gerstner, Sabine; Bogner, Franz X.

2010-05-01

Our study monitored the cognitive and motivational effects within different educational instruction schemes: On the one hand, teacher-centred versus hands-on instruction; on the other hand, hands-on instruction with and without a knowledge consolidation phase (concept mapping). All the instructions dealt with the same content. For all participants, the hands-on approach as well as the concept mapping adaptation were totally new. Our hands-on approach followed instruction based on "learning at work stations". A total of 397 high-achieving fifth graders participated in our study. We used a pre-test, post-test, retention test design both to detect students' short-term learning success and long-term learning success, and to document their decrease rates of newly acquired knowledge. Additionally, we monitored intrinsic motivation. Although the teacher-centred approach provided higher short-term learning success, hands-on instruction resulted in relatively lower decrease rates. However, after six weeks, all students reached similar levels of newly acquired knowledge. Nevertheless, concept mapping as a knowledge consolidation phase positively affected short-term increase in knowledge. Regularly placed in instruction, it might increase long-term retention rates. Scores of interest, perceived competence and perceived choice were very high in all the instructional schemes.

Stent Design Affects Femoropopliteal Artery Deformation.

Science.gov (United States)

MacTaggart, Jason; Poulson, William; Seas, Andreas; Deegan, Paul; Lomneth, Carol; Desyatova, Anastasia; Maleckis, Kaspars; Kamenskiy, Alexey

2018-03-23

Poor durability of femoropopliteal artery (FPA) stenting is multifactorial, and severe FPA deformations occurring with limb flexion are likely involved. Different stent designs result in dissimilar stent-artery interactions, but the degree of these effects in the FPA is insufficiently understood. To determine how different stent designs affect limb flexion-induced FPA deformations. Retrievable markers were deployed into n = 28 FPAs of lightly embalmed human cadavers. Bodies were perfused and CT images were acquired with limbs in the standing, walking, sitting, and gardening postures. Image analysis allowed measurement of baseline FPA foreshortening, bending, and twisting associated with each posture. Markers were retrieved and 7 different stents were deployed across the adductor hiatus in the same limbs. Markers were then redeployed in the stented FPAs, and limbs were reimaged. Baseline and stented FPA deformations were compared to determine the influence of each stent design. Proximal to the stent, Innova, Supera, and SmartFlex exacerbated foreshortening, SmartFlex exacerbated twisting, and SmartControl restricted bending of the FPA. Within the stent, all devices except Viabahn restricted foreshortening; Supera, SmartControl, and AbsolutePro restricted twisting; SmartFlex and Innova exacerbated twisting; and Supera and Viabahn restricted bending. Distal to the stents, all devices except AbsolutePro and Innova exacerbated foreshortening, and Viabahn, Supera, Zilver, and SmartControl exacerbated twisting. All stents except Supera were pinched in flexed limb postures. Peripheral self-expanding stents significantly affect limb flexion-induced FPA deformations, but in different ways. Although certain designs seem to accommodate some deformation modes, no device was able to match all FPA deformations.

Complex surface deformation of Akutan volcano, Alaska revealed from InSAR time series

Science.gov (United States)

Wang, Teng; DeGrandpre, Kimberly; Lu, Zhong; Freymueller, Jeffrey T.

2018-02-01

Akutan volcano is one of the most active volcanoes in the Aleutian arc. An intense swarm of volcano-tectonic earthquakes occurred across the island in 1996. Surface deformation after the 1996 earthquake sequence has been studied using Interferometric Synthetic Aperture Radar (InSAR), yet it is hard to determine the detailed temporal behavior and spatial extent of the deformation due to decorrelation and the sparse temporal sampling of SAR data. Atmospheric delay anomalies over Akutan volcano are also strong, bringing additional technical challenges. Here we present a time series InSAR analysis from 2003 to 2016 to reveal the surface deformation in more detail. Four tracks of Envisat data acquired from 2003 to 2010 and one track of TerraSAR-X data acquired from 2010 to 2016 are processed to produce high-resolution surface deformation, with a focus on studying two transient episodes of inflation in 2008 and 2014. For the TerraSAR-X data, the atmospheric delay is estimated and removed using the common-master stacking method. These derived deformation maps show a consistently uplifting area on the northeastern flank of the volcano. From the TerraSAR-X data, we quantify the velocity of the subsidence inside the caldera to be as high as 10 mm/year, and identify another subsidence area near the ground cracks created during the 1996 swarm.

Multi-scale analysis of deformation behavior at SCC crack tip (2). (Contract research)

International Nuclear Information System (INIS)

Kaji, Yoshiyuki; Miwa, Yukio; Tsukada, Takashi; Hayakawa, Masao; Nagashima, Nobuo

2007-03-01

This report describes a result of the research conducted by the Japan Atomic Energy Agency and the National Institute for Materials Science under contract with Japan Nuclear Energy Safety Organization (JNES) that was concerned with a multi-scale analysis of plastic deformation behavior at the crack tip of stress corrosion cracking (SCC). The research was carried out to evaluate the validity of the SCC growth data acquired in the intergranular SCC (IGSCC) project based on a mechanistic understanding of SCC. For the purpose, in this research, analyses of the plastic deformation behavior and microstructure around the crack tip were performed in a nano-order scale. The hardness measured in nano, meso and macro scales was employed as a common index of the strength, and the essential data necessary to understand the SCC propagation behavior were acquired and analyzed that are mainly a size of plastic deformation region and a microstructural information in the region, e.g. data of crystallografy, microscopic deformation and dislocations at the inside of grains and grain boundaries. In this year, we analyzed the state of plastic deformation region at the crack tip of IGSCC under various conditions and investigated relationship between crack growth behavior and stress intensity factor. Especially, we investigated in detail about two different hardened specimens used in the SCC growth tests in the IGSCC project. (J.P.N.)

Precision grip in congenital and acquired hemiparesis: similarities in impairments and implications for neurorehabilitation - review

Directory of Open Access Journals (Sweden)

Yannick eBleyenheuft

2014-06-01

Full Text Available Background: Patients with congenital and acquired hemiparesis incur long-term functional deficits, among which the loss of prehension that may impact their functional independence. Identifying, understanding and comparing the underlying mechanisms of prehension impairments represent an opportunity to better adapt neurorehabilitationObjective: The present review aims to provide a better understanding of precision grip deficits in congenital and acquired hemiparesis and to determine whether the severity and type of fine motor control impairments depend on whether or not the lesions are congenital or acquired in adulthood. Methods: Using combinations of the following key words: fingertip force, grip force, precision grip, cerebral palsy, stroke, pubmed and Scopus databases were used to search studies from 1984 to 2013. Results: Individuals with both congenital and acquired hemiparesis were able to some extent to use anticipatory motor control in precision grip tasks, even if this control was impaired in the paretic hand. In both congenital or acquired hemiparesis, the ability to plan efficient anticipatory motor control when the less-affected hand is used provides a possibility to remediate impairments in anticipatory motor control of the paretic hand. Conclusion: Surprisingly we observed very few differences between the results of studies in children with congenital hemiplegia and stroke patients. We suggest that the underlying specific strategies of neurorehabilitation developed for each one could benefit the other.

All Madelung deformities are not endocrine.

Science.gov (United States)

Kumar, Ajay; Rai, Gopal K; Akhtar, Javed; Phillip, Rajeev; Gutch, Manish; Arya, T V S

2013-10-01

Madelung deformity is a rare inherited disorder associated with endocrine disorders like Turner's syndrome, pseudohypoparathyroidism, but can be seen with short stature homeobox deficiency conditions such as Leri-Weill dyschondrosteosis (LWD) and Langers mesomelic dysplasia. It has also been reported following trauma to the distal radius epiphysis neoplasia mucopolysaccharidosis (MPS) and achondroplasia. Madelung deformity is an abnormality of distal radial epiphysis where in progressive ulnar and volar tilt of the articular surface occurring in association with distal subluxation of ulna. A 13-year-old girl was referred to us for evaluation of bilateral deformity of wrist and short stature. There was ulnar deviation and dorsal tilt of bilateral hands without history of pain to the joint trauma and family history of similar illness. On X-ray, wrist showed malformed distal radial epiphysis with dorsal and ulnar shift and with increased length of phalanges suggestive of Madelung deformity. X-ray spine was normal. Ultrasound abdomen showed normal uterus and ovary and her follicle stimulating hormone. Luteinizing hormone was normal and so was urine MPS screening. Based on the above points the diagnosis of LWD was made.

All Madelung deformities are not endocrine

Directory of Open Access Journals (Sweden)

Ajay Kumar

2013-01-01

Full Text Available Madelung deformity is a rare inherited disorder associated with endocrine disorders like Turner′s syndrome, pseudohypoparathyroidism, but can be seen with short stature homeobox deficiency conditions such as Leri-Weill dyschondrosteosis (LWD and Langers mesomelic dysplasia. It has also been reported following trauma to the distal radius epiphysis neoplasia mucopolysaccharidosis (MPS and achondroplasia. Madelung deformity is an abnormality of distal radial epiphysis where in progressive ulnar and volar tilt of the articular surface occurring in association with distal subluxation of ulna. A 13-year-old girl was referred to us for evaluation of bilateral deformity of wrist and short stature. There was ulnar deviation and dorsal tilt of bilateral hands without history of pain to the joint trauma and family history of similar illness. On X-ray, wrist showed malformed distal radial epiphysis with dorsal and ulnar shift and with increased length of phalanges suggestive of Madelung deformity. X-ray spine was normal. Ultrasound abdomen showed normal uterus and ovary and her follicle stimulating hormone. Luteinizing hormone was normal and so was urine MPS screening. Based on the above points the diagnosis of LWD was made.

Automatic Generation of 3D Caricatures Based on Artistic Deformation Styles.

Science.gov (United States)

Clarke, Lyndsey; Chen, Min; Mora, Benjamin

2011-06-01

Caricatures are a form of humorous visual art, usually created by skilled artists for the intention of amusement and entertainment. In this paper, we present a novel approach for automatic generation of digital caricatures from facial photographs, which capture artistic deformation styles from hand-drawn caricatures. We introduced a pseudo stress-strain model to encode the parameters of an artistic deformation style using "virtual" physical and material properties. We have also developed a software system for performing the caricaturistic deformation in 3D which eliminates the undesirable artifacts in 2D caricaturization. We employed a Multilevel Free-Form Deformation (MFFD) technique to optimize a 3D head model reconstructed from an input facial photograph, and for controlling the caricaturistic deformation. Our results demonstrated the effectiveness and usability of the proposed approach, which allows ordinary users to apply the captured and stored deformation styles to a variety of facial photographs.

Lateral column lengthening for acquired adult flatfoot deformity caused by posterior tibial tendon dysfunction stage II: a retrospective comparison of calcaneus osteotomy with calcaneocuboid distraction arthrodesis.

Science.gov (United States)

Haeseker, Guus A; Mureau, Marc A; Faber, Frank W M

2010-01-01

In this study, clinical and radiological results after lateral column lengthening by calcaneocuboid distraction arthrodesis and calcaneus osteotomy were compared. Thirty-three patients (35 feet) treated with lateral column lengthening by distraction arthrodesis (14 patients, 16 feet; group I) or by calcaneus osteotomy (19 patients, 19 feet; group II) for adult-acquired flatfoot deformity caused by stage II posterior tibial tendon dysfunction were compared retrospectively. Mean follow-up was 42.4 months (range, 6-78 months) for group I and 15.8 months (range, 6-32 months) for group II (P lengthening by means of calcaneus osteotomy rather than distraction arthrodesis of the calcaneocuboid joint, for correction of stage II posterior tibial tendon dysfunction. Copyright 2010 American College of Foot and Ankle Surgeons. Published by Elsevier Inc. All rights reserved.

SU-E-J-218: Novel Validation Paradigm of MRI to CT Deformation of Prostate

Energy Technology Data Exchange (ETDEWEB)

Padgett, K [University of Miami School of Medicine - Radiation Oncology, Miami, FL (United States); University of Miami School of Medicine - Radiology, Miami, FL (United States); Pirozzi, S; Nelson, A; Piper, J; Horvat, M [MIM Software Inc., Cleveland, OH (United States); Stoyanova, R; Dogan, N; Pollack, A [University of Miami School of Medicine - Radiation Oncology, Miami, FL (United States)

2015-06-15

Purpose: Deformable registration algorithms are inherently difficult to characterize in the multi-modality setting due to a significant differences in the characteristics of the different modalities (CT and MRI) as well as tissue deformations. We present a unique paradigm where this is overcome by utilizing a planning-MRI acquired within an hour of the planning-CT serving as a surrogate for quantifying MRI to CT deformation by eliminating the issues of multi-modality comparisons. Methods: For nine subjects, T2 fast-spin-echo images were acquired at two different time points, the first several weeks prior to planning (diagnostic-MRI) and the second on the same day as the planning-CT (planning-MRI). Significant effort in patient positioning and bowel/bladder preparation was undertaken to minimize distortion of the prostate in all datasets. The diagnostic-MRI was rigidly and deformably aligned to the planning-CT utilizing a commercially available deformable registration algorithm synthesized from local registrations. Additionally, the quality of rigid alignment was ranked by an imaging physicist. The distances between corresponding anatomical landmarks on rigid and deformed registrations (diagnostic-MR to planning-CT) were evaluated. Results: It was discovered that in cases where the rigid registration was of acceptable quality the deformable registration didn’t improve the alignment, this was true of all metrics employed. If the analysis is separated into cases where the rigid alignment was ranked as unacceptable the deformable registration significantly improved the alignment, 4.62mm residual error in landmarks as compared to 5.72mm residual error in rigid alignments with a p-value of 0.0008. Conclusion: This paradigm provides an ideal testing ground for MR to CT deformable registration algorithms by allowing for inter-modality comparisons of multi-modality registrations. Consistent positioning, bowel and bladder preparation may Result in higher quality rigid

SU-F-I-50: Finite Element-Based Deformable Image Registration of Lung and Heart

Energy Technology Data Exchange (ETDEWEB)

Penjweini, R [University of Pennsylvania, Philadelphia, Pennsylvania (United States); Kim, M [University of Pennsylvania, Philadelphia, PA (United States); Zhu, T [University Pennsylvania, Philadelphia, PA (United States)

2016-06-15

Purpose: Photodynamic therapy (PDT) is used after surgical resection to treat the microscopic disease for malignant pleural mesothelioma and to increase survival rates. Although accurate light delivery is imperative to PDT efficacy, the deformation of the pleural volume during the surgery impacts the delivered light dose. To facilitate treatment planning, we use a finite-element-based (FEM) deformable image registration to quantify the anatomical variation of lung and heart volumes between CT pre-(or post-) surgery and surface contours obtained during PDT using an infrared camera-based navigation system (NDI). Methods: NDI is used during PDT to obtain the information of the cumulative light fluence on every cavity surface point that is being treated. A wand, comprised of a modified endotrachial tube filled with Intralipid and an optical fiber inside the tube, is used to deliver the light during PDT. The position of the treatment is tracked using an attachment with nine reflective passive markers that are seen by the NDI system. Then, the position points are plotted as three-dimensional volume of the pleural cavity using Matlab and Meshlab. A series of computed tomography (CT) scans of the lungs and heart, in the same patient, are also acquired before and after the surgery. The NDI and CT contours are imported into COMSOL Multiphysics, where the FEM-based deformable image registration is obtained. The NDI and CT contours acquired during and post-PDT are considered as the reference, and the Pre-PDT CT contours are used as the target, which will be deformed. Results: Anatomical variation of the lung and heart volumes, taken at different times from different imaging devices, was determined by using our model. The resulting three-dimensional deformation map along x, y and z-axes was obtained. Conclusion: Our model fuses images acquired by different modalities and provides insights into the variation in anatomical structures over time.

Accelerating dewetting on deformable substrates by adding a liquid underlayer.

Science.gov (United States)

Xu, Lin; Reiter, Günter; Shi, Tongfei; An, Lijia

2010-05-18

We investigated the dependence of the dewetting velocity of a thin, low-viscosity polystyrene (PS) top film on a poly(methyl methacrylate) (PMMA) double layer consisting of a low-viscosity underlayer of thickness h(L) coated with a high-viscosity middle layer of thickness h(M). The addition of the liquid underlayer generated complex nonmonotonic behavior of the dewetting velocity as a function of increasing h(M). In particular, we observed an acceleration of dewetting for an intermediate range of h(M). This phenomenon has been interpreted by a combination deformation of the middle elastic layer and a concurrent change in the contact angle. On one hand, deformation led to the formation of a trench that dissipated energy during its movement through the liquid underlayer and thus caused a slowing down of dewetting. However, with an increase in the thickness of the elastic middle layer, the size of the trench decreased and its influence on the dewetting velocity also decreased. On the other hand, the deformation of the elastic layer also led to an increase in the contact angle. This increase in the driving capillary forces caused an increase in the dewetting velocity.

Deformation of two-phase aggregates using standard numerical methods

Science.gov (United States)

Duretz, Thibault; Yamato, Philippe; Schmalholz, Stefan M.

2013-04-01

Geodynamic problems often involve the large deformation of material encompassing material boundaries. In geophysical fluids, such boundaries often coincide with a discontinuity in the viscosity (or effective viscosity) field and subsequently in the pressure field. Here, we employ popular implementations of the finite difference and finite element methods for solving viscous flow problems. On one hand, we implemented finite difference method coupled with a Lagrangian marker-in-cell technique to represent the deforming fluid. Thanks to it Eulerian nature, this method has a limited geometric flexibility but is characterized by a light and stable discretization. On the other hand, we employ the Lagrangian finite element method which offers full geometric flexibility at the cost of relatively heavier discretization. In order to test the accuracy of the finite difference scheme, we ran large strain simple shear deformation of aggregates containing either weak of strong circular inclusion (1e6 viscosity ratio). The results, obtained for different grid resolutions, are compared to Lagrangian finite element results which are considered as reference solution. The comparison is then used to establish up to which strain can finite difference simulations be run given the nature of the inclusions (dimensions, viscosity) and the resolution of the Eulerian mesh.

The Use of the Analytic Hierarchy Process to Aid Decision Making in Acquired Equinovarus Deformity

NARCIS (Netherlands)

van Til, Janine Astrid; Renzenbrink, G.J.; Dolan, J.G.; IJzerman, Maarten Joost

2008-01-01

Objective: To increase the transparency of decision making about treatment in patients with equinovarus deformity poststroke. - Design: The analytic hierarchy process (AHP) was used as a structured methodology to study the subjective rationale behind choice of treatment. - Setting: An 8-hour meeting

Formation of defects at high temperature plastic deformation of gallium arsenide

Energy Technology Data Exchange (ETDEWEB)

Mikhnovich, V.V.

2006-03-14

The purpose of the present thesis consists in acquiring more concrete information concerning the mechanism of the movement of dislocations and types of defects that appear during the process of dislocation motion on the basis of systematic experimental studies of the GaAs deformation. Experimental studies concerning the dependence of the stress of the samples from their deformation at different values of the deformation parameters (like temperature and deformation speed) were conducted in this paper. To determine the concentration of defects introduced in samples during the deformation process the positron annihilation spectroscopy (PAS) method was used. The second chapter of this paper deals with models of movement of dislocations and origination of defects during deformation of the samples. In the third chapter channels and models of positron annihilation in the GaAs samples are investigated. In the forth chapter the used experimental methods, preparation procedure of test samples and technical data of conducted experiments are described. The fifth chapter shows the results of deformation experiments. The sixth chapter shows the results of positron lifetime measurements by the PAS method. In the seventh chapter one can find analyses of the values of defects concentration that were introduced in samples during deformation. (orig.)

The use of polyurethane foam as an antimicrobial dressing material in hand surgery

Directory of Open Access Journals (Sweden)

Nebil Yesiloglu

2015-12-01

Full Text Available Polyurethane foam is generally used in negative pressure-assisted wound closure therapy. It provides an antimicrobial environment around the wound, while reducing the rate of skin maceration. The authors used polyurethane foam in routine hand dressings after hand surgery operations that were performed for both congenital and acquired purposes. [Hand Microsurg 2015; 4(3.000: 91-92

Illumination-Invariant and Deformation-Tolerant Inner Knuckle Print Recognition Using Portable Devices

Directory of Open Access Journals (Sweden)

Xuemiao Xu

2015-02-01

Full Text Available We propose a novel biometric recognition method that identifies the inner knuckle print (IKP. It is robust enough to confront uncontrolled lighting conditions, pose variations and low imaging quality. Such robustness is crucial for its application on portable devices equipped with consumer-level cameras. We achieve this robustness by two means. First, we propose a novel feature extraction scheme that highlights the salient structure and suppresses incorrect and/or unwanted features. The extracted IKP features retain simple geometry and morphology and reduce the interference of illumination. Second, to counteract the deformation induced by different hand orientations, we propose a novel structure-context descriptor based on local statistics. To our best knowledge, we are the first to simultaneously consider the illumination invariance and deformation tolerance for appearance-based low-resolution hand biometrics. Settings in previous works are more restrictive. They made strong assumptions either about the illumination condition or the restrictive hand orientation. Extensive experiments demonstrate that our method outperforms the state-of-the-art methods in terms of recognition accuracy, especially under uncontrolled lighting conditions and the flexible hand orientation requirement.

Numerical study of suspensions of deformable particles.

Science.gov (United States)

Brandt, Luca; Rosti, Marco Edoardo

2017-11-01

We consider a model non-Newtonian fluid consisting of a suspension of deformable particles in a Newtonian solvent. Einstein showed in his pioneering work that the relative increase in effective viscosity is a linear function of the particle volume fraction for dilute suspensions of rigid particles. Inertia has been shown to introduce deviations from the behaviour predicted by the different empirical fits, an effect that can be related to an increase of the effective volume fraction. We here focus on the effect of elasticity, i.e. visco-elastic deformable particles. To tackle the problem at hand, we perform three-dimensional Direct Numerical Simulation of a plane Couette flow with a suspension of neutrally buoyant deformable viscous hyper-elastic particles. We show that elasticity produces a shear-thinning effect in elastic suspensions (in comparison to rigid ones) and that it can be understood in terms of a reduction of the effective volume fraction of the suspension. The deformation modifies the particle motion reducing the level of mutual interaction. Normal stress differences will also be considered. European Research Council, Grant No. ERC-2013-CoG- 616186, TRITOS; SNIC (the Swedish National Infrastructure for Computing).

Modelling and Simulation of Structural Deformation of Isothermal Subsurface Flow and Carbon Dioxide Injection

KAUST Repository

El-Amin, Mohamed

2011-05-15

Injection of CO2 in hydrocarbon reservoir has double benefit. On the one hand, it is a profitable method due to issues related to global warming, and on the other hand it is an effective mechanism to enhance hydrocarbon recovery. Such injection associates complex processes involving, e.g., solute transport of dissolved materials, in addition to local changes in density of the phases. Also, increasing carbon dioxide injection may cause a structural deformation of the medium, so it is important to include such effect into the model. The structural deformation modelling in carbon sequestration is important to evaluate the medium stability to avoid CO2 leakage to the atmosphere. On the other hand, geologic formation of the medium is usually heterogeneous and consists of several layers of different permeability. In this work we conduct numerical simulation of two-phase flow in a heterogeneous porous medium domain with dissolved solute transport as well as structural deformation effects. The solute transport of the dissolved component is described by concentration equation. The structural deformation for geomechanics is derived from a general local differential balance equation with neglecting the local mass balance of solid phase and the inertial force term. The flux continuity condition is used at interfaces between different permeability layers of the heterogeneous medium. We analyze the vertical migration of a CO2 plume injected into a 2D layered reservoir. Analysis of distribution of flow field components such as saturation, pressures, velocities, and CO2 concentration are presented.

Alloy-dependent deformation behavior of highly ductile nanocrystalline AuCu thin films

International Nuclear Information System (INIS)

Lohmiller, Jochen; Spolenak, Ralph; Gruber, Patric A.

2014-01-01

Nanocrystalline thin films on compliant substrates become increasingly important for the development of flexible electronic devices. In this study, nanocrystalline AuCu thin films on polyimide substrate were tested in tension while using a synchrotron-based in situ testing technique. Analysis of X-ray diffraction profiles allowed identifying the underlying deformation mechanisms. Initially, elastic and microplastic deformation is observed, followed by dislocation-mediated shear band formation, and eventually macroscopic crack formation. Particularly the influence of alloy composition, heat-treatment, and test temperature were investigated. Generally, a highly ductile behavior is observed. However, high Cu concentrations, annealing, and/or large plastic strains lead to localized deformation and hence reduced ductility. On the other hand, enhanced test temperature allows for a delocalized deformation and extended ductility

Alloy-dependent deformation behavior of highly ductile nanocrystalline AuCu thin films

Energy Technology Data Exchange (ETDEWEB)

Lohmiller, Jochen [Karlsruhe Institute of Technology, Institute for Applied Materials, P.O. Box 3640, 76021 Karlsruhe (Germany); Laboratory for Nanometallurgy, Department of Materials, ETH Zurich, Wolfgang-Pauli-Str. 10, 8093 Zurich (Switzerland); Spolenak, Ralph [Laboratory for Nanometallurgy, Department of Materials, ETH Zurich, Wolfgang-Pauli-Str. 10, 8093 Zurich (Switzerland); Gruber, Patric A., E-mail: patric.gruber@kit.edu [Karlsruhe Institute of Technology, Institute for Applied Materials, P.O. Box 3640, 76021 Karlsruhe (Germany)

2014-02-10

Nanocrystalline thin films on compliant substrates become increasingly important for the development of flexible electronic devices. In this study, nanocrystalline AuCu thin films on polyimide substrate were tested in tension while using a synchrotron-based in situ testing technique. Analysis of X-ray diffraction profiles allowed identifying the underlying deformation mechanisms. Initially, elastic and microplastic deformation is observed, followed by dislocation-mediated shear band formation, and eventually macroscopic crack formation. Particularly the influence of alloy composition, heat-treatment, and test temperature were investigated. Generally, a highly ductile behavior is observed. However, high Cu concentrations, annealing, and/or large plastic strains lead to localized deformation and hence reduced ductility. On the other hand, enhanced test temperature allows for a delocalized deformation and extended ductility.

Deformations of super Riemann surfaces

International Nuclear Information System (INIS)

Ninnemann, H.

1992-01-01

Two different approaches to (Konstant-Leites-) super Riemann surfaces are investigated. In the local approach, i.e. glueing open superdomains by superconformal transition functions, deformations of the superconformal structure are discussed. On the other hand, the representation of compact super Riemann surfaces of genus greater than one as a fundamental domain in the Poincare upper half-plane provides a simple description of super Laplace operators acting on automorphic p-forms. Considering purely odd deformations of super Riemann surfaces, the number of linear independent holomorphic sections of arbitrary holomorphic line bundles will be shown to be independent of the odd moduli, leading to a simple proof of the Riemann-Roch theorem for compact super Riemann surfaces. As a further consequence, the explicit connections between determinants of super Laplacians and Selberg's super zeta functions can be determined, allowing to calculate at least the 2-loop contribution to the fermionic string partition function. (orig.)

Deformations of super Riemann surfaces

Energy Technology Data Exchange (ETDEWEB)

Ninnemann, H [Hamburg Univ. (Germany). 2. Inst. fuer Theoretische Physik

1992-11-01

Two different approaches to (Konstant-Leites-) super Riemann surfaces are investigated. In the local approach, i.e. glueing open superdomains by superconformal transition functions, deformations of the superconformal structure are discussed. On the other hand, the representation of compact super Riemann surfaces of genus greater than one as a fundamental domain in the Poincare upper half-plane provides a simple description of super Laplace operators acting on automorphic p-forms. Considering purely odd deformations of super Riemann surfaces, the number of linear independent holomorphic sections of arbitrary holomorphic line bundles will be shown to be independent of the odd moduli, leading to a simple proof of the Riemann-Roch theorem for compact super Riemann surfaces. As a further consequence, the explicit connections between determinants of super Laplacians and Selberg's super zeta functions can be determined, allowing to calculate at least the 2-loop contribution to the fermionic string partition function. (orig.).

A biometric authentication model using hand gesture images.

Science.gov (United States)

Fong, Simon; Zhuang, Yan; Fister, Iztok; Fister, Iztok

2013-10-30

A novel hand biometric authentication method based on measurements of the user's stationary hand gesture of hand sign language is proposed. The measurement of hand gestures could be sequentially acquired by a low-cost video camera. There could possibly be another level of contextual information, associated with these hand signs to be used in biometric authentication. As an analogue, instead of typing a password 'iloveu' in text which is relatively vulnerable over a communication network, a signer can encode a biometric password using a sequence of hand signs, 'i' , 'l' , 'o' , 'v' , 'e' , and 'u'. Subsequently the features from the hand gesture images are extracted which are integrally fuzzy in nature, to be recognized by a classification model for telling if this signer is who he claimed himself to be, by examining over his hand shape and the postures in doing those signs. It is believed that everybody has certain slight but unique behavioral characteristics in sign language, so are the different hand shape compositions. Simple and efficient image processing algorithms are used in hand sign recognition, including intensity profiling, color histogram and dimensionality analysis, coupled with several popular machine learning algorithms. Computer simulation is conducted for investigating the efficacy of this novel biometric authentication model which shows up to 93.75% recognition accuracy.

Reconstruction of bilateral tibial aplasia and split hand-foot syndrome in a father and daughter.

Science.gov (United States)

Al Kaissi, Ali; Ganger, Rudolf; Klaushofer, Klaus; Grill, Franz

2014-01-01

Tibial aplasia is of heterogeneous aetiology, the majority of reports are sporadic. We describe the reconstruction procedures in two subjects - a daughter and father manifested autosomal dominant (AD) inheritance of the bilateral tibial aplasia and split hand-foot syndrome. Reconstruction of these patients required multiple surgical procedures and orthoprosthesis was mandatory. The main goal of treatment was to achieve walking. Stabilization of the ankle joint by fibular-talar-chondrodesis on both sides, followed by bilateral Brown-procedure at the knee joint level has been applied accordingly. The outcome was with improved function of the deformed limbs and walking was achieved with simultaneous designation of orthotic fitting. This is the first study encompassing the diagnosis and management of a father and daughter with bilateral tibial aplasia associated with variable split hand/foot deformity without foot ablation. Our patients showed the typical AD pattern of inheritance of split-hand/foot and tibial aplasia.

Restoration of the central slip in congenital form of boutonniere deformity: case report.

Science.gov (United States)

Kim, Jong-Pil; Go, Jai-Hyang; Hwang, Chang-Hwan; Shin, Won-Jeong

2014-10-01

We present a case of a congenital form of a boutonniere deformity involving both little fingers with a poorly differentiated extensor mechanism and the absence of the tendinous attachment on the dorsal aspect of the middle phalanx. This complex deformity was evaluated histologically followed by successful reconstruction of the central slip. Copyright © 2014 American Society for Surgery of the Hand. Published by Elsevier Inc. All rights reserved.

Interseismic Deformation along the Red River Fault from InSAR Measurements

Science.gov (United States)

Chen, J.; Li, Z.; Clarke, P. J.

2017-12-01

The Red River Fault (RRF) zone is a profound geological discontinuity separating South China from Indochina. Right lateral movements along this >900 km fault are considered to accommodate the extrusion of SE China. Crustal deformation monitoring at high resolution is the key to understand the present-day mode of deformation in this zone and its interaction with the adjacent regions. This is the first study to measure the interseismic deformation of the entire fault with ALOS-1/2 and Sentinel-1 observations. Nine ascending tracks of ALOS-1 data between 2007 and 2011 are collected from the Alaska Satellite Facility (ASF), four descending tracks of Sentinel-1 data are acquired every 24 days since October 2014, and ALOS-2 data are being systematically acquired since 2014. The long wavelength (L-band) of ALOS-1/2 and short temporal baseline of Sentinel-1 ensure good coherence to overcome the limitations of heavy vegetation and variable climate in the region. Stacks of interferograms are generated by our automatic processing chain based on the InSAR Scientific Computing Environment (ISCE) software, ionospheric errors are estimated and corrected using the split-spectrum method (Fattahi et al., IEEE Trans. Geosci. Remote Sens., 2017) and the tropospheric delays are calibrated using the Generic Atmospheric Correction Online Service for InSAR (GACOS: http://ceg-research.ncl.ac.uk/v2/gacos) with high-resolution ECMWF products (Yu et al., J. Geophys. Res., 2017). Time series analysis is performed to determine the interseismic deformation rate of the RRF using the in-house InSAR time series with atmospheric estimation model (InSAR TS + AEM) package based on the Small Baseline Subset (SBAS) algorithm. Our results reveal the decrease of slip rate from north to south. We map the interseismic strain rate field to characterize the deformation patterns and seismic hazard throughout the RRF zone.

On the feasibility of interoperable schemes in hand biometrics.

Science.gov (United States)

Morales, Aythami; González, Ester; Ferrer, Miguel A

2012-01-01

Personal recognition through hand-based biometrics has attracted the interest of many researchers in the last twenty years. A significant number of proposals based on different procedures and acquisition devices have been published in the literature. However, comparisons between devices and their interoperability have not been thoroughly studied. This paper tries to fill this gap by proposing procedures to improve the interoperability among different hand biometric schemes. The experiments were conducted on a database made up of 8,320 hand images acquired from six different hand biometric schemes, including a flat scanner, webcams at different wavelengths, high quality cameras, and contactless devices. Acquisitions on both sides of the hand were included. Our experiment includes four feature extraction methods which determine the best performance among the different scenarios for two of the most popular hand biometrics: hand shape and palm print. We propose smoothing techniques at the image and feature levels to reduce interdevice variability. Results suggest that comparative hand shape offers better performance in terms of interoperability than palm prints, but palm prints can be more effective when using similar sensors.

On the Feasibility of Interoperable Schemes in Hand Biometrics

Science.gov (United States)

Morales, Aythami; González, Ester; Ferrer, Miguel A.

2012-01-01

Personal recognition through hand-based biometrics has attracted the interest of many researchers in the last twenty years. A significant number of proposals based on different procedures and acquisition devices have been published in the literature. However, comparisons between devices and their interoperability have not been thoroughly studied. This paper tries to fill this gap by proposing procedures to improve the interoperability among different hand biometric schemes. The experiments were conducted on a database made up of 8,320 hand images acquired from six different hand biometric schemes, including a flat scanner, webcams at different wavelengths, high quality cameras, and contactless devices. Acquisitions on both sides of the hand were included. Our experiment includes four feature extraction methods which determine the best performance among the different scenarios for two of the most popular hand biometrics: hand shape and palm print. We propose smoothing techniques at the image and feature levels to reduce interdevice variability. Results suggest that comparative hand shape offers better performance in terms of interoperability than palm prints, but palm prints can be more effective when using similar sensors. PMID:22438714

Search for right-handed currents in muon decay

International Nuclear Information System (INIS)

Carr, J.

The experiment is motivated by the recent interest in left-right symmetric theories based on the gauge group SU(2)sub(R) x SU(2)sub(L) x U(1). Such theories are left-right symmetric at the Lagrangian level but account for the apparently maximal parity violation at present energies by assuming that the right-handed gauge boson Wsub(R) has acquired, through spontaneous symmetry breaking, a mass larger than its left-handed counterpart Wsub(L). A search is made for deviations from maximal parity violation by observing the muon decay rate when the decay positron is emitted with momentum close to the kinematic limit and opposite to the muon spin direction. This decay rate approaches zero at the kinematic limit for purely left-handed W's (V-A) but is large for right-handed W's (V+A). From the data, bounds on the right-handed gauge boson mass and also on non-(V or A) couplings can be set. (author)

An image-guided tool to prevent hospital acquired infections

Science.gov (United States)

Nagy, Melinda; Szilágyi, László; Lehotsky, Ákos; Haidegger, Tamás; Benyó, Balázs

2011-03-01

Hospital Acquired Infections (HAI) represent the fourth leading cause of death in the United States, and claims hundreds of thousands of lives annually in the rest of the world. This paper presents a novel low-cost mobile device|called Stery-Hand|that helps to avoid HAI by improving hand hygiene control through providing an objective evaluation of the quality of hand washing. The use of the system is intuitive: having performed hand washing with a soap mixed with UV re ective powder, the skin appears brighter in UV illumination on the disinfected surfaces. Washed hands are inserted into the Stery-Hand box, where a digital image is taken under UV lighting. Automated image processing algorithms are employed in three steps to evaluate the quality of hand washing. First, the contour of the hand is extracted in order to distinguish the hand from the background. Next, a semi-supervised clustering algorithm classies the pixels of the hand into three groups, corresponding to clean, partially clean and dirty areas. The clustering algorithm is derived from the histogram-based quick fuzzy c-means approach, using a priori information extracted from reference images, evaluated by experts. Finally, the identied areas are adjusted to suppress shading eects, and quantied in order to give a verdict on hand disinfection quality. The proposed methodology was validated through tests using hundreds of images recorded in our laboratory. The proposed system was found robust and accurate, producing correct estimation for over 98% of the test cases. Stery-Hand may be employed in general practice, and it may also serve educational purposes.

Toward the development of intrafraction tumor deformation tracking using a dynamic multi-leaf collimator

Energy Technology Data Exchange (ETDEWEB)

Ge, Yuanyuan; O’Brien, Ricky T.; Shieh, Chun-Chien; Keall, Paul J., E-mail: paul.keall@sydney.edu.au [Radiation Physics Laboratory, University of Sydney, NSW 2006 (Australia); Booth, Jeremy T. [Northern Sydney Cancer Centre, Royal North Shore Hospital, Sydney, NSW 2065 (Australia)

2014-06-15

Purpose: Intrafraction deformation limits targeting accuracy in radiotherapy. Studies show tumor deformation of over 10 mm for both single tumor deformation and system deformation (due to differential motion between primary tumors and involved lymph nodes). Such deformation cannot be adapted to with current radiotherapy methods. The objective of this study was to develop and experimentally investigate the ability of a dynamic multi-leaf collimator (DMLC) tracking system to account for tumor deformation. Methods: To compensate for tumor deformation, the DMLC tracking strategy is to warp the planned beam aperture directly to conform to the new tumor shape based on real time tumor deformation input. Two deformable phantoms that correspond to a single tumor and a tumor system were developed. The planar deformations derived from the phantom images in beam's eye view were used to guide the aperture warping. An in-house deformable image registration software was developed to automatically trigger the registration once new target image was acquired and send the computed deformation to the DMLC tracking software. Because the registration speed is not fast enough to implement the experiment in real-time manner, the phantom deformation only proceeded to the next position until registration of the current deformation position was completed. The deformation tracking accuracy was evaluated by a geometric target coverage metric defined as the sum of the area incorrectly outside and inside the ideal aperture. The individual contributions from the deformable registration algorithm and the finite leaf width to the tracking uncertainty were analyzed. Clinical proof-of-principle experiment of deformation tracking using previously acquired MR images of a lung cancer patient was implemented to represent the MRI-Linac environment. Intensity-modulated radiation therapy (IMRT) treatment delivered with enabled deformation tracking was simulated and demonstrated. Results: The first

Radiographic findings of the hand and foot in patients with systemic lupus erythematosus

International Nuclear Information System (INIS)

Scutellari, P.N.; Stabellini, R.; Orzincolo, C.; Franceschini, F.; Govoni, M.; Trotta, F.

1987-01-01

A detail examination of the hands and feet was performed in a group of 34 patients affected by systemic lupus erythematosus (SLE), using low-dose mammographic film and Rank Xerox selenium plate, according to current diagnostic techniques. All patients presented articular symptoms (pain and arthralgia). The high incidence (38.8%) of patients with no radiographic evidence of bone damage-even though articular symptoms are present-is emphasized. In such cases, it is very difficult to distinguish SLE from rheumatoid arthritis, especially as far as therapeutic management and prognosis are concerned. The lack of any pathognomonic radiological sign of the lupus arthritis, in the hands as well as in the feet, is then stressed. Nevertheless, artropathy in SLE is defined as a deforming unerosive arthritis, with a typical symmetric distribution, affecting most commonly (according to incidence) the proximal interphalangeal and metacarpophalangeal joints. In the hand, arthropathy is referred to as Jaccoud's type arthritis, because it is characterized by joint deformities which can be corrected. In the foot, the main abnormalities include hallux valgus, subluxation of the matatarsophalangeal joints and widening of the forefoot

Radiographic findings of the hand and foot in patients with systemic lupus erythematosus

Energy Technology Data Exchange (ETDEWEB)

Scutellari, P N; Stabellini, R; Orzincolo, C; Franceschini, F; Govoni, M; Trotta, F

1987-01-01

A detail examination of the hands and feet was performed in a group of 34 patients affected by systemic lupus erythematosus (SLE), using low-dose mammographic film and Rank Xerox selenium plate, according to current diagnostic techniques. All patients presented articular symptoms (pain and arthralgia). The high incidence (38.8%) of patients with no radiographic evidence of bone damage-even though articular symptoms are present-is emphasized. In such cases, it is very difficult to distinguish SLE from rheumatoid arthritis, especially as far as therapeutic management and prognosis are concerned. The lack of any pathognomonic radiological sign of the lupus arthritis, in the hands as well as in the feet, is then stressed. Nevertheless, artropathy in SLE is defined as a deforming unerosive arthritis, with a typical symmetric distribution, affecting most commonly (according to incidence) the proximal interphalangeal and metacarpophalangeal joints. In the hand, arthropathy is referred to as Jaccoud's type arthritis, because it is characterized by joint deformities which can be corrected. In the foot, the main abnormalities include hallux valgus, subluxation of the matatarsophalangeal joints and widening of the forefoot.

Infection Control in Child Day Care Centres : Development and evaluation of a hand hygiene intervention

NARCIS (Netherlands)

T.P. Zomer (Tizza)

2015-01-01

markdownabstract__Abstract__ Children attending child day care centres are at increased risk of acquiring gastrointestinal and respiratory infections compared to children cared for at home. Hand hygiene is known to be an effective measure to prevent infections. However, compliance with hand

Nuclear fuel deformation phenomena

International Nuclear Information System (INIS)

Van Brutzel, L.; Dingreville, R.; Bartel, T.J.

2015-01-01

Nuclear fuel encounters severe thermomechanical environments. Its mechanical response is profoundly influenced by an underlying heterogeneous microstructure but also inherently dependent on the temperature and stress level histories. The ability to adequately simulate the response of such microstructures, to elucidate the associated macroscopic response in such extreme environments is crucial for predicting both performance and transient fuel mechanical responses. This chapter discusses key physical phenomena and the status of current modelling techniques to evaluate and predict fuel deformations: creep, swelling, cracking and pellet-clad interaction. This chapter only deals with nuclear fuel; deformations of cladding materials are discussed elsewhere. An obvious need for a multi-physics and multi-scale approach to develop a fundamental understanding of properties of complex nuclear fuel materials is presented. The development of such advanced multi-scale mechanistic frameworks should include either an explicit (domain decomposition, homogenisation, etc.) or implicit (scaling laws, hand-shaking,...) linkage between the different time and length scales involved, in order to accurately predict the fuel thermomechanical response for a wide range of operating conditions and fuel types (including Gen-IV and TRU). (authors)

Dosimetric and geometric evaluation of the use of deformable image registration in adaptive intensity-modulated radiotherapy for head-and-neck cancer

DEFF Research Database (Denmark)

Eiland, R B; Maare, Christian; Sjöström, D

2014-01-01

CT) and a cone beam CT (CBCT). The CBCT was acquired on the same day (± 1 d) as the ReCT (i.e. at Fraction 17, 18, 23, 24 or 29). The ReCT served as ground truth. A deformed CT (dCT) with structures was created by deforming the pCT to the CBCT. The geometrical comparison was based on the volumes of the deformed...

Electric/magnetic deformations of S3 and AdS3, and geometric cosets

International Nuclear Information System (INIS)

Israel, D.; Kounnas, C.; Marios Petropoulos, P.; Orlando, D.

2005-01-01

We analyze asymmetric marginal deformations of SU(2) k and SL(2,R) k WZW models. These appear in heterotic string backgrounds with non-vanishing Neveu-Schwarz three-forms plus electric or magnetic fields, depending on whether the deformation is elliptic, hyperbolic or parabolic. Asymmetric deformations create new families of exact string vacua. The geometries which are generated in this way, deformed S 3 or AdS 3 , include in particular geometric cosets such as S 2 , AdS 2 or H 2 . Hence, the latter are consistent, exact conformal sigma models, with electric or magnetic backgrounds. We discuss various geometric and symmetry properties of the deformations at hand as well as their spectra and partition functions, with special attention to the supersymmetric AdS 2 x S 2 background. We also comment on potential holographic applications. (Abstract Copyright [2005], Wiley Periodicals, Inc.)

Reconstruction of bilateral tibial aplasia and split hand-foot syndrome in a father and daughter

Directory of Open Access Journals (Sweden)

Ali Al Kaissi

2014-01-01

Full Text Available Background: Tibial aplasia is of heterogeneous aetiology, the majority of reports are sporadic. We describe the reconstruction procedures in two subjects - a daughter and father manifested autosomal dominant (AD inheritance of the bilateral tibial aplasia and split hand-foot syndrome. Materials and Methods: Reconstruction of these patients required multiple surgical procedures and orthoprosthesis was mandatory. The main goal of treatment was to achieve walking. Stabilization of the ankle joint by fibular-talar-chondrodesis on both sides, followed by bilateral Brown-procedure at the knee joint level has been applied accordingly. Results: The outcome was with improved function of the deformed limbs and walking was achieved with simultaneous designation of orthotic fitting. Conclusion: This is the first study encompassing the diagnosis and management of a father and daughter with bilateral tibial aplasia associated with variable split hand/foot deformity without foot ablation. Our patients showed the typical AD pattern of inheritance of split-hand/foot and tibial aplasia.

Ultra fine grained Ti prepared by severe plastic deformation

Science.gov (United States)

Lukáč, F.; Čížek, J.; Knapp, J.; Procházka, I.; Zháňal, P.; Islamgaliev, R. K.

2016-01-01

The positron annihilation spectroscopy was employed for characterisation of defects in pure Ti with ultra fine grained (UFG) structure. UFG Ti samples were prepared by two techniques based on severe plastic deformation (SPD): (i) high pressure torsion (HPT) and (ii) equal channel angular pressing (ECAP). Although HPT is the most efficient technique for grain refinement, the size of HPT-deformed specimens is limited. On the other hand, ECAP is less efficient in grain refinement but enables to produce larger samples more suitable for industrial applications. Characterisation of defects by positron annihilation spectroscopy was accompanied by hardness testing in order to monitor the development of mechanical properties of UFG Ti.

Infant Hand Preference and the Development of Cognitive Abilities

Directory of Open Access Journals (Sweden)

George Frederick Michel

2016-03-01

Full Text Available Hand preference develops in the first two postnatal years with nearly half of infants exhibiting a consistent early preference for acquiring objects. Others exhibit a more variable developmental trajectory but by the end of their second postnatal year, most exhibit a consistent hand preference for role-differentiated bimanual manipulation. According to some forms of embodiment theory, these differences in hand use patterns should influence the way children interact with their environments, which, in turn, should affect the structure and function of brain development. Such early differences in brain development should result in different trajectories of psychological development. We present evidence that children with consistent early hand preferences exhibit advanced patterns of cognitive development as compared to children who develop a hand preference later. Differences in the developmental trajectory of hand preference are predictive of developmental differences in language, object management skills, and tool-use skills. As predicted by Cassasanto’s body-specificity hypothesis, infants with different hand preferences proceed along different developmental pathways of cognitive functioning.

A new approach to hand-based authentication

Science.gov (United States)

Amayeh, G.; Bebis, G.; Erol, A.; Nicolescu, M.

2007-04-01

Hand-based authentication is a key biometric technology with a wide range of potential applications both in industry and government. Traditionally, hand-based authentication is performed by extracting information from the whole hand. To account for hand and finger motion, guidance pegs are employed to fix the position and orientation of the hand. In this paper, we consider a component-based approach to hand-based verification. Our objective is to investigate the discrimination power of different parts of the hand in order to develop a simpler, faster, and possibly more accurate and robust verification system. Specifically, we propose a new approach which decomposes the hand in different regions, corresponding to the fingers and the back of the palm, and performs verification using information from certain parts of the hand only. Our approach operates on 2D images acquired by placing the hand on a flat lighting table. Using a part-based representation of the hand allows the system to compensate for hand and finger motion without using any guidance pegs. To decompose the hand in different regions, we use a robust methodology based on morphological operators which does not require detecting any landmark points on the hand. To capture the geometry of the back of the palm and the fingers in suffcient detail, we employ high-order Zernike moments which are computed using an effcient methodology. The proposed approach has been evaluated on a database of 100 subjects with 10 images per subject, illustrating promising performance. Comparisons with related approaches using the whole hand for verification illustrate the superiority of the proposed approach. Moreover, qualitative comparisons with state-of-the-art approaches indicate that the proposed approach has comparable or better performance.

Effects of hand hygiene education and individual feedback on hand hygiene behaviour, MRSA acquisition rate and MRSA colonization pressure among intensive care unit nurses.

Science.gov (United States)

Chun, Hee-Kyung; Kim, Kyung-Mi; Park, Ho-Ran

2015-12-01

This study was conducted to increase the frequency and level of thoroughness of hand hygiene practice by nurses, and to assess the influence of the methicillin-resistant Staphylococcus aureus (MRSA) acquired incidence rate and the MRSA colonization pressure in a medical intensive care unit (MICU). A total of 24 MICU nurses received hand hygiene education and individual feedback of hand hygiene frequency and method after a session of education, and two posteducation evaluations were followed. The frequency of hand hygiene (P = 0.001) and the methodology score of hand hygiene increased significantly (P = 0.001). The MRSA acquisition rate decreased significantly, from 11.1% before the education to 0% after (P = 0.014). The MRSA colonization pressure decreased significantly from 39.5% to 8.6% after the education sessions (P = 0.001). This indicates that providing individual feedback after hand hygiene education was very effective in increasing nurses' hand hygiene frequency and improving hand hygiene method; furthermore, it was expected to decrease health care-associated infections. © 2014 Wiley Publishing Asia Pty Ltd.

Adherence to hand hygiene protocol by clinicians and medical ...

African Journals Online (AJOL)

Background: While communicable diseases are the leading causes of morbidity and mortality in Malawi, the contribution of nosocomial or hospital-acquired infections (HAIs) is unknown but could be substantial. The single most important method of preventing nosocomial infections is hand hygiene. We report a study which ...

Bacterial contamination of white coats and hands of healthcare ...

African Journals Online (AJOL)

Background: Transmission of hospital acquired infections (HAIs) may be associated with contamination of healthcare workers' (HCWs) hands and white coats. Objective: The purpose of this study was to clarify the role of HCWs' white coats in transmitting HAIs and to determine the association between bacterial ...

Cytomegalovirus survival and transferability and the effectiveness of common hand-washing agents against cytomegalovirus on live human hands.

Science.gov (United States)

Stowell, Jennifer D; Forlin-Passoni, Daniela; Radford, Kay; Bate, Sheri L; Dollard, Sheila C; Bialek, Stephanie R; Cannon, Michael J; Schmid, D Scott

2014-01-01

Congenital cytomegalovirus (CMV) transmission can occur when women acquire CMV while pregnant. Infection control guidelines may reduce risk for transmission. We studied the duration of CMV survival after application of bacteria to the hands and after transfer from the hands to surfaces and the effectiveness of cleansing with water, regular and antibacterial soaps, sanitizer, and diaper wipes. Experiments used CMV AD169 in saliva at initial titers of 1 × 10(5) infectious particles/ml. Samples from hands or surfaces (points between 0 and 15 min) were placed in culture and observed for at least 2 weeks. Samples were also tested using CMV real-time PCR. After application of bacteria to the hands, viable CMV was recovered from 17/20 swabs at 0 min, 18/20 swabs at 1 min, 5/20 swabs at 5 min, and 4/20 swabs at 15 min. After transfer, duration of survival was at least 15 min on plastic (1/2 swabs), 5 min on crackers and glass (3/4 swabs), and 1 min or less on metal and cloth (3/4 swabs); no viable virus was collected from wood, rubber, or hands. After cleansing, no viable virus was recovered using water (0/22), plain soap (0/20), antibacterial soap (0/20), or sanitizer (0/22). Viable CMV was recovered from 4/20 hands 10 min after diaper wipe cleansing. CMV remains viable on hands for sufficient times to allow transmission. CMV may be transferred to surfaces with reduced viability. Hand-cleansing methods were effective at eliminating viable CMV from hands.

Effect of deformations on the compactness of odd-Z superheavy nuclei formed in cold and hot fusion reactions

Science.gov (United States)

Kaur, Gurjit; Sandhu, Kirandeep; Sharma, Manoj K.

2018-03-01

Using the extended fragmentation theory, the compactness of hot and cold fusion reactions is analyzed for odd-Z nuclei ranging Z = 105- 117. The calculations for the present work are carried out at T = 0MeV and ℓ = 0 ħ, as the temperature and angular momentum effects remain silent while addressing the orientation degree of freedom (i.e. compact angle configuration). In the hot fusion, 48Ca (spherical) + actinide (prolate) reaction, the non-equatorial compact (nec) shape is obtained for Z = 113 nucleus. On the other hand, Z > 113 nuclei favor equatorial compact (ec) configuration. The distribution of barrier height (VB) illustrate that the ec-shape is obtained when the magnitude of quadrupole deformation of the nucleus is higher than the hexadecupole deformation. In other words, negligible or small -ve β4-deformations support ec configurations. On the other hand, large (+ve) magnitude of the β4-deformation suggests that the configuration appears for compact angle θc < 90 °, leading to nec structure. Similar deformation effects are observed for Bi-induced reactions, in which not belly-to-belly compact (nbbc) configurations are seen at θc = 42 °. In addition to the effect of β2 and β4-deformations, the exclusive role of octupole deformations (β3) is also analyzed. The β3-deformations do not follow the reflection symmetry as that of β2 and β4, leading to the possible occurrence of compact configuration within 0° to 180° angular range.

On the Feasibility of Interoperable Schemes in Hand Biometrics

Directory of Open Access Journals (Sweden)

Miguel A. Ferrer

2012-02-01

Full Text Available Personal recognition through hand-based biometrics has attracted the interest of many researchers in the last twenty years. A significant number of proposals based on different procedures and acquisition devices have been published in the literature. However, comparisons between devices and their interoperability have not been thoroughly studied. This paper tries to fill this gap by proposing procedures to improve the interoperability among different hand biometric schemes. The experiments were conducted on a database made up of 8,320 hand images acquired from six different hand biometric schemes, including a flat scanner, webcams at different wavelengths, high quality cameras, and contactless devices. Acquisitions on both sides of the hand were included. Our experiment includes four feature extraction methods which determine the best performance among the different scenarios for two of the most popular hand biometrics: hand shape and palm print. We propose smoothing techniques at the image and feature levels to reduce interdevice variability. Results suggest that comparative hand shape offers better performance in terms of interoperability than palm prints, but palm prints can be more effective when using similar sensors.

Permanent deformation and deflection relationship from pavement condition assessment

Directory of Open Access Journals (Sweden)

Fabricio Leiva-Villacorta

2017-07-01

Full Text Available The development of permanent deformation in flexible pavements has been a research topic for several decades. Currently there are models included in the structural design of pavements that can predict this type of failure. However, the variables required for the prediction of this distress are complex or difficult to obtain in the field, making its application in pavement evaluation also difficult. Measurement of the deflection of pavement structures by means of non-destructive testing is a technique used to assess the condition of the pavement. This research study seeks to correlate data from deflections of the pavement surface with probable permanent deformation in time. In addition, prediction of the remaining life of the pavement structure using a specified criterion is also analyzed. In order to accomplish these objectives, data acquired from 4 different full scale accelerated pavement test tracks was used to develop a permanent deformation model as a function of deflection, load repetitions and pavement layer thickness. The developed model considered a time series model that incorporates an Auto-regressive parameter of order 1. The proposed model presents an advantage over currently available models because it reduces the required parameters to predict the permanent deformation and/or remaining life in the structure and because these variables can be easily found and updated in a pavement management system. Keywords: HVS, Permanent deformation, Deflections, APT, Time series, Instrumentation

Strength and Deformability of Light-toned Layered Deposits Observed by MER Opportunity: Eagle to Erebus Craters

Science.gov (United States)

Okubo, C. H.; Schultz, R. A.; Nahm, A. L.

2007-07-01

The strength and deformability of light-toned layered deposits are estimated based on measurements of porosity from Microscopic Imager data acquired by MER Opportunity during its traverse from Eagle Crater to Erebus Crater.

THE KNOWLEDGE OF HEALTH CARE WORKERS AND DOCTORS REGARDING HAND SCRUB

Directory of Open Access Journals (Sweden)

Rahul Sanjeev Chaudhary

2016-08-01

Full Text Available BACKGROUND Hand hygiene practices of health care workers has been shown to be an effective measure in preventing hospital acquired infections. This concept has been aptly used to improve understanding, training, monitoring, and reporting hand hygiene among healthcare workers. We conducted this study to assess the knowledge of doctors and health care workers regarding hand scrub. METHODS A study was conducted among doctors and health care workers in a tertiary care hospital. Knowledge was evaluated by using self-structured questionnaire based on the guidelines of hand hygiene prescribed by WHO. RESULTS The awareness and knowledge of preoperative surgical hand scrubbing was moderate in doctors, but unfortunately poor in HCWs. CONCLUSION Our study highlights the need for introducing measures in order to increase the knowledge of preoperative hand scrub in teaching hospital which may translate into good practices.

Superposed ruptile deformational events revealed by field and VOM structural analysis

Science.gov (United States)

Kumaira, Sissa; Guadagnin, Felipe; Keller Lautert, Maiara

2017-04-01

Virtual outcrop models (VOM) is becoming an important application in the analysis of geological structures due to the possibility of obtaining the geometry and in some cases kinematic aspects of analyzed structures in a tridimensional photorealistic space. These data are used to gain quantitative information on the deformational features which coupled with numeric models can assist in understands deformational processes. Old basement units commonly register superposed deformational events either ductile or ruptile along its evolution. The Porongos Belt, located at southern Brazil, have a complex deformational history registering at least five ductile and ruptile deformational events. In this study, we presents a structural analysis of a quarry in the Porongos Belt, coupling field and VOM structural information to understand process involved in the last two deformational events. Field information was acquired using traditional structural methods for analysis of ruptile structures, such as the descriptions, drawings, acquisition of orientation vectors and kinematic analysis. VOM was created from the image-based modeling method through photogrammetric data acquisition and orthorectification. Photogrammetric data acquisition was acquired using Sony a3500 camera and a total of 128 photographs were taken from ca. 10-20 m from the outcrop in different orientations. Thirty two control point coordinates were acquired using a combination of RTK dGPS surveying and total station work, providing a precision of few millimeters for x, y and z. Photographs were imported into the Photo Scan software to create a 3D dense point cloud from structure from-motion algorithm, which were triangulated and textured to generate the VOM. VOM was georreferenced (oriented and scaled) using the ground control points, and later analyzed in OpenPlot software to extract structural information. Data was imported in Wintensor software to obtain tensor orientations, and Move software to process and

Deformed special relativity with an invariant minimum speed and its ...

Indian Academy of Sciences (India)

On the other hand, according to special relativity (SR), the momentum cannot ... Deformed special relativity with an invariant minimum speed ..... However, we need to show that there is an anti-gravitational interaction between the ordinary proof mass m and the big sphere with a 'dark mass' of vacuum (MΛ), but let us first ...

Surgical treatment results of hand deformities in patients with Apert syndrome

Directory of Open Access Journals (Sweden)

Ufuk Nalbantoglu

2015-12-01

Results: The mean age at the first operation was 2.7 years and the mean number of operations was 3 per patient. No patient developed graft-flap necrosis and no patients required amputations. All patients were able to perform grasping and pinching functions and families were satisfied with the cosmetic results. Conclusion: Using a two-stage surgical protocol, achieving satisfactory results with a minimal number of operations is possible in patients with Apert Syndrome. [Hand Microsurg 2015; 4(3.000: 53-57

THE EFFECT OF ACQUISITION ON THE STOCK RETURNS OF ACQUIRING COMPANIES: EXAMINING THE EFFECT OF ACQUISITIONS OCCURED THROUGH THE PERMISSION OF CAPITAL MARKET BOARD ON THE STOCK RETURNS OF ACQUIRING COMPANIES

Directory of Open Access Journals (Sweden)

LEVENT ÇITAK

2013-06-01

Full Text Available A merger can be defined as the economical and legal integration of two or more firms. On the other hand, an acquisiton is the transfer of all asssets and liabilities of the target firm to the acquiring firm. In the literature, merger and acquisition concepts can be used interchangeably. Firms tend to merge for the sake of creating snergy, competitive advantage, diversification, increasing firm value etc. Mergers and acquisitions are sometimes in favour of acquiring firms’ stock holders and sometimes target firms’ stock holders. Merger gains change, depending on the type of the merger and form of payment. In this study, mergers that occured through the permission of Capital Market Board have been used for the analyses. Of the mergers which have the permission, acquiring firms that are listed on Istanbul Stock Exchange have been considered and postacquisition buy and hold abnormal returns and cumulative abnormal returns have been calculated. It is concluded that postacquisition abnormal returns aren’t statistically significant. On the other hand, 1 month, 3 month, 6 month, 1 year and 2 year buy and hold abnormal returns and cumulative abnormal returns of the acquiring firms that use different payment methods are not statistically different from each other, on the basis of same return horizon. Two different methods of abnormal return calculation don’t make any difference in postacquisition abnormal returns, either.

An educational intervention to improve hand hygiene compliance in Vietnam.

Science.gov (United States)

Phan, Hang Thi; Tran, Hang Thi Thuy; Tran, Hanh Thi My; Dinh, Anh Pham Phuong; Ngo, Ha Thanh; Theorell-Haglow, Jenny; Gordon, Christopher J

2018-03-07

Hand hygiene compliance is the basis of infection control programs. In developing countries models to improve hand hygiene compliance to reduce healthcare acquired infections are required. The aim of this study was to determine hand hygiene compliance following an educational program in an obstetric and gynecological hospital in Vietnam. Health care workers from neonatal intensive care, delivery suite and a surgical ward from Hung Vuong Hospital, Ho Chi Minh City, Vietnam undertook a 4-h educational program targeting hand hygiene. Compliance was monitored monthly for six months following the intervention. Hand hygiene knowledge was assessed at baseline and after six months of the study. There were 7124 opportunities over 370 hand hygiene recording sessions with 1531 opportunities at baseline and 1620 at 6 months following the intervention. Hand hygiene compliance increased significantly from baseline across all sites (43.6% [95% Confidence interval CI: 41.1-46.1] to 63% [95% CI: 60.6-65.3]; p hygiene compliance increased significantly after intervention (p hygiene compliance for an extended period of time. Hand hygiene knowledge increased during the intervention. This hand hygiene model could be used in developing countries were resources are limited.

Low-cost design and fabrication of an anthropomorphic robotic hand.

Science.gov (United States)

Junaid, Ali Bin; Tahir, Sanan; Rasheed, Tahir; Ahmed, Sharjeel; Sohail, Mehreen; Afzal, Muhammad Raheel; Ali, Muzaffar; Kim, Yoonsoo

2014-10-01

Human hand signifies a magnificent and challenging example for scientists and engineers trying to replicate its complex structure and functionality. This paper proposes a bio-mechatronic approach for the design of an anthropomorphic artificial hand capable of performing basic human hand motions with fundamental gripping functionality. The dexterity of the artificial hand is exhibited by imitating the natural motion of the human fingers. Imitation is produced according to the data acquired from the flex sensors attached to the human fingers. In order to have proper gripping, closed-loop control is implemented using the tactile sensors. Feedback for the closed-loop control is provided by force sensing resistors (FSRs), attached on the fingertips of the robotic hand. These sensors also enable handling of fragile objects. The mathematical model is derived using forward kinematics and also simulated on MATLAB to ascertain the position of robotic fingers in 3D space.

Electromyography data for non-invasive naturally-controlled robotic hand prostheses.

Science.gov (United States)

Atzori, Manfredo; Gijsberts, Arjan; Castellini, Claudio; Caputo, Barbara; Hager, Anne-Gabrielle Mittaz; Elsig, Simone; Giatsidis, Giorgio; Bassetto, Franco; Müller, Henning

2014-01-01

Recent advances in rehabilitation robotics suggest that it may be possible for hand-amputated subjects to recover at least a significant part of the lost hand functionality. The control of robotic prosthetic hands using non-invasive techniques is still a challenge in real life: myoelectric prostheses give limited control capabilities, the control is often unnatural and must be learned through long training times. Meanwhile, scientific literature results are promising but they are still far from fulfilling real-life needs. This work aims to close this gap by allowing worldwide research groups to develop and test movement recognition and force control algorithms on a benchmark scientific database. The database is targeted at studying the relationship between surface electromyography, hand kinematics and hand forces, with the final goal of developing non-invasive, naturally controlled, robotic hand prostheses. The validation section verifies that the data are similar to data acquired in real-life conditions, and that recognition of different hand tasks by applying state-of-the-art signal features and machine-learning algorithms is possible.

Hand hygiene in emergency medical services.

Science.gov (United States)

Teter, Jonathan; Millin, Michael G; Bissell, Rick

2015-01-01

Hospital-acquired infections (HAIs) affect millions of patients annually (World Health Organization. Guidelines on Hand Hygiene in Healthcare. Geneva: WHO Press; 2009). Hand hygiene compliance of clinical staff has been identified by numerous studies as a major contributing factor to HAIs around the world. Infection control and hand hygiene in the prehospital environment can also contribute to patient harm and spread of infections. Emergency medical services (EMS) practitioners are not monitored as closely as hospital personnel in terms of hand hygiene training and compliance. Their ever-changing work environment is less favorable to traditional hospital-based aseptic techniques and education. This study aimed to determine the current state of hand hygiene practices among EMS providers and to provide recommendations for improving practices in the emergency health services environment. This study was a prospective, observational prevalence study and survey, conducted over a 2-month period. We selected participants from visits to three selected hospital emergency departments in the mid-Atlantic region. There were two data components to the study: a participant survey and hand swabs for pathogenic cultures. This study recruited a total sample of 62 participants. Overall, the study revealed that a significant number of EMS providers (77%) have a heavy bacterial load on their hands after patient care. All levels of providers had a similar distribution of bacterial load. Survey results revealed that few providers perform hand hygiene before (34%) or in between patients (24%), as recommended by the Centers for Disease Control and Prevention guidelines. This study demonstrates that EMS providers are potential vectors of microorganisms if proper hand hygiene is not performed properly. Since EMS providers treat a variety of patients and operate in a variety of environments, providers may be exposed to potentially pathogenic organisms, serving as vectors for the exposure of

Orientation sensitive deformation in Zr alloys: experimental and modeling studies

International Nuclear Information System (INIS)

Srivastava, D.; Keskar, N.; Manikrishna, K.V.; Dey, G.K.; Jha, S.K.; Saibaba, N.

2016-01-01

Zirconium alloys are used for fuel cladding and other structural components in pressurised heavy water nuclear reactors (PHWR's). Currently there is a lot of interest in developing alloys for structural components for higher temperature reactor operation. There is also need for development of cladding material with better corrosion and mechanical property of cladding material for higher and extended burn up applications. The performance of the cladding material is primarily influenced by the microstructural features of the material such as constituent phases their morphology, precipitates characteristics, nature of defects etc. Therefore, the microstructure is tailored as per the performance requirement by through controlled additions of alloying elements, thermo-mechanical- treatments. In order to obtain the desired microstructure, it is important to know the deformation behaviour of the material. Orientation dependent deformation behavior was studied in Zr using a combination of experimental and modeling (both discrete and atomistic dislocation dynamics) methods. Under the conditions of plane strain deformation, it was observed that single phase Zr, had significant extent of deformation heterogeneity based on local orientations. Discrete dislocation dynamics simulations incorporating multi slip systems had captured the orientation sensitive deformation. MD dislocations on the other hand brought the fundamental difference in various crystallographic orientations in determining the nucleating stress for the dislocations. The deformed structure has been characterized using X-ray, electron and neutron diffraction techniques. The various operating deformation mechanism will be discussed in this presentation. (author)

Assessment of knowledge of hand washing among health care ...

African Journals Online (AJOL)

Introduction. Nosocomial infection is a global public health problem with an estimated 1.5 million suffering consequences at any given time [1, 2] noted that at least 25% of all hospital infections in the developing world are nosocomially acquired. The hands of health care providers are major agents of infection transmission ...

Vertebral Column Resection for Rigid Spinal Deformity.

Science.gov (United States)

Saifi, Comron; Laratta, Joseph L; Petridis, Petros; Shillingford, Jamal N; Lehman, Ronald A; Lenke, Lawrence G

2017-05-01

Broad narrative review. To review the evolution, operative technique, outcomes, and complications associated with posterior vertebral column resection. A literature review of posterior vertebral column resection was performed. The authors' surgical technique is outlined in detail. The authors' experience and the literature regarding vertebral column resection are discussed at length. Treatment of severe, rigid coronal and/or sagittal malalignment with posterior vertebral column resection results in approximately 50-70% correction depending on the type of deformity. Surgical site infection rates range from 2.9% to 9.7%. Transient and permanent neurologic injury rates range from 0% to 13.8% and 0% to 6.3%, respectively. Although there are significant variations in EBL throughout the literature, it can be minimized by utilizing tranexamic acid intraoperatively. The ability to correct a rigid deformity in the spine relies on osteotomies. Each osteotomy is associated with a particular magnitude of correction at a single level. Posterior vertebral column resection is the most powerful posterior osteotomy method providing a successful correction of fixed complex deformities. Despite meticulous surgical technique and precision, this robust osteotomy technique can be associated with significant morbidity even in the most experienced hands.

Optical dynamic deformation measurements at translucent materials.

Science.gov (United States)

Philipp, Katrin; Koukourakis, Nektarios; Kuschmierz, Robert; Leithold, Christoph; Fischer, Andreas; Czarske, Jürgen

2015-02-15

Due to their high stiffness-to-weight ratio, glass fiber-reinforced polymers are an attractive material for rotors, e.g., in the aerospace industry. A fundamental understanding of the material behavior requires non-contact, in-situ dynamic deformation measurements. The high surface speeds and particularly the translucence of the material limit the usability of conventional optical measurement techniques. We demonstrate that the laser Doppler distance sensor provides a powerful and reliable tool for monitoring radial expansion at fast rotating translucent materials. We find that backscattering in material volume does not lead to secondary signals as surface scattering results in degradation of the measurement volume inside the translucent medium. This ensures that the acquired signal contains information of the rotor surface only, as long as the sample surface is rough enough. Dynamic deformation measurements of fast-rotating fiber-reinforced polymer composite rotors with surface speeds of more than 300 m/s underline the potential of the laser Doppler sensor.

Three-Dimensional Dynamic Deformation Measurements Using Stereoscopic Imaging and Digital Speckle Photography

International Nuclear Information System (INIS)

Prentice, H. J.; Proud, W. G.

2006-01-01

A technique has been developed to determine experimentally the three-dimensional displacement field on the rear surface of a dynamically deforming plate. The technique combines speckle analysis with stereoscopy, using a modified angular-lens method: this incorporates split-frame photography and a simple method by which the effective lens separation can be adjusted and calibrated in situ. Whilst several analytical models exist to predict deformation in extended or semi-infinite targets, the non-trivial nature of the wave interactions complicates the generation and development of analytical models for targets of finite depth. By interrogating specimens experimentally to acquire three-dimensional strain data points, both analytical and numerical model predictions can be verified more rigorously. The technique is applied to the quasi-static deformation of a rubber sheet and dynamically to Mild Steel sheets of various thicknesses

Exploring quantum physics through hands-on projects

CERN Document Server

Prutchi, David

2012-01-01

Build an intuitive understanding of the principles behind quantum mechanics through practical construction and replication of original experiments With easy-to-acquire, low-cost materials and basic knowledge of algebra and trigonometry, Exploring Quantum Physics through Hands-on Projects takes readers step by step through the process of re-creating scientific experiments that played an essential role in the creation and development of quantum mechanics. From simple measurements of Planck's constant to testing violations of Bell's inequalities using entangled photons, Exploring Quantum Physics through Hands-on Projects not only immerses readers in the process of quantum mechanics, it provides insight into the history of the field--how the theories and discoveries apply to our world not only today, but also tomorrow. By immersing readers in groundbreaking experiments that can be performed at home, school, or in the lab, this first-ever, hands-on book successfully demystifies the world of quantum physics for...

Are the N and Δ deformed MIT bags

International Nuclear Information System (INIS)

Clement, G.; Maamache, M.

1985-01-01

The influence of the one-gluon exchange interaction, zero-point energy, and centre-of-mass correction, on the deformation of the nucleon and Δ bags, is studied in the MIT bag model. If the sharp MIT boundary conditions are taken seriously, the strong dependence of the zero-point energy on the deformation leads to the collapse of the N and Δ bags for realistic values of the strong fine structure constant α/sub S/. If on the other hand the zero-point energy is ignored altogether, then the nucleon, spherical for α/sub S/ 3.25, while the Δ is always prolate. The various predictions of the model are, for α/sub S/> or approx. =3.25, consistent with experiment, except for the proton magnetic moment which is only about 40% of the experimental value

Diagnostic imaging of the hand. 3. rev. and enl. ed.

International Nuclear Information System (INIS)

Schmitt, Rainer; Lanz, Ulrich

2015-01-01

The book on diagnostic imaging of the hand covers the following issues: projection radiography, cinematography, MRT and CR arthrography, arthroscopy, arteriography, skeleton scintiscanning, sonography, computerized tomography, magnetic resonance tomography, anatomy of forearm and carpus, anatomy of metacarpus and fingers, carpal function and morphometry, postoperative X-ray diagnostic, growing hand skeleton, normative variants, malformations and deformities, trauma of the distal forearm, lesions of the ulnocarpal complex (TFCC), scaphoid fractures, scaphoid arthrosis, fractures of other carpus bones, carpal luxations and luxation fractures, carpal instabilities, fractures of the metacarpalla, finger fractures, arthrosis deformans, enthesiopathies, sport induced soft tissue lesions, osteonecrosis, impingement syndromes, osteopenic skeletal diseases, metabolis diseases, crystal-induced osteoarthropaties, rheumatoid arthritis, spondyloarthritis, rheumatic fever, collagenoses, infective arthritis, osteomyelitis, soft tissue infections, cystoids bone lesions, skeletal tumors, soft tissue tumors, carpal tunnel syndrome, nerve compression syndrome, arterial perfusion disturbances, differential diagnostic tables on hand lesions.

Real-time model for simulating a tracked vehicle on deformable soils

Directory of Open Access Journals (Sweden)

Martin Meywerk

2016-05-01

Full Text Available Simulation is one possibility to gain insight into the behaviour of tracked vehicles on deformable soils. A lot of publications are known on this topic, but most of the simulations described there cannot be run in real-time. The ability to run a simulation in real-time is necessary for driving simulators. This article describes an approach for real-time simulation of a tracked vehicle on deformable soils. The components of the real-time model are as follows: a conventional wheeled vehicle simulated in the Multi Body System software TRUCKSim, a geometric description of landscape, a track model and an interaction model between track and deformable soils based on Bekker theory and Janosi–Hanamoto, on one hand, and between track and vehicle wheels, on the other hand. Landscape, track model, soil model and the interaction are implemented in MATLAB/Simulink. The details of the real-time model are described in this article, and a detailed description of the Multi Body System part is omitted. Simulations with the real-time model are compared to measurements and to a detailed Multi Body System–finite element method model of a tracked vehicle. An application of the real-time model in a driving simulator is presented, in which 13 drivers assess the comfort of a passive and an active suspension of a tracked vehicle.

Breath alcohol of anesthesiologists using alcohol hand gel and the "five moments for hand hygiene" in routine practice.

Science.gov (United States)

Lindsay, Helen A; Hannam, Jacqueline A; Bradfield, Charles N; Mitchell, Simon J

2016-08-01

Appropriate hand hygiene reduces hospital-acquired infections. Anesthesiologists work in environments with numerous hand hygiene opportunities (HHOs). In a prospective observational study, we investigated the potential for an anesthesiologist to return a positive alcohol breath test during routine practice when using alcohol hand gel. We observed ten volunteer anesthesiologists over four hours while they implemented the World Health Organization (WHO) "five moments for hand hygiene" using our hospital's adopted standard 70% ethanol hand gel. We measured the expired alcohol concentration at shift start and every fifteen minutes thereafter with a fuel cell breathalyzer calibrated to measure the percentage of blood alcohol concentration (BAC). Blood alcohol specimens (analyzed with gas chromatography) were collected at shift start and, when possible, immediately after a participant's first positive breathalyzer test. Of the 130 breathalyzer tests obtained, there were eight (6.2%) positive breath alcohol results from six of the ten participants, all within two minutes of a HHO. The highest value breathalyzer BAC recorded was 0.064%, with an overall mean (SD) of 0.023 (0.017)%. Five (62.5%) of the positive breathalyzer tests returned to zero in less than seven minutes. All of three blood specimens obtained immediately after a positive breathalyzer reading tested negative for alcohol. Anesthesia practitioners using alcohol hand gel in a manner that conforms with recommended hand hygiene can test positive for alcohol on a breathalyzer assay. Positive tests probably arose from inhalation of alcohol vapour into the respiratory dead space following gel application. If workplace breath testing for alcohol is implemented, it should be completed more than 15 min after applying alcohol hand gel. Positive results should be verified with a BAC test.

Diagnostic significance of the radiologic appearances of the hands in systemic lupus erythematosus (SLE)

Energy Technology Data Exchange (ETDEWEB)

Winkler, P; Baenkler, H W; Pfuhl, E; Gutmann, W

1980-09-01

40 patients with SLE were assessed, the diagnoses being made according to modified ARA-criteria; the hand films of 25 of these patients were analysed. The most important roentgenologic findings consisted of reducible deformities with mild or absent articular changes in the deformed MCP and PIP joints. As these changes often occur late in the course of SLE, a primary radiological diagnosis was possible in only three cases (8%), whereas hand films provided confirmatory evidence of disease in a further seven patients. These roentgenological characteristics of SLE were found significantly less often in patients with definite RA; this group tended to have positive ANF (antinuclear factors). Antibodies against DNA may be absent, especially in a less active phase of disease. ANF is non-specific, and SLE simulates RA in 10-20% of cases. It is, therefore, very important in individual cases to consider the diagnosis of SLE in the presence of deformity without corresponding articular changes. Direct comparison of both the p.a. and oblique views is essential in the evaluation of reducible deformities, although this point has not been stressed in the literature. Reducible deformities may be overlooked in physical examination, when the patient gives no history of functional disability. The main differential diagnosis is Jaccoud's arthropathy, which is rarely seen in a general hospital. Most of these patients give a history of recurrent rheumatic fever, a minority complain about joint pain or disability, approximately 90% show signs indicating a valvular lesion of the heart, over 75% have a normal ESR and a positive rheumatoid or antinuclear factor is very rarely found. The distinction from SLE or rheumatoid arthritis is therefore easily established on additional non-radiological criteria.

A novel deformation mechanism for superplastic deformation

Energy Technology Data Exchange (ETDEWEB)

Muto, H.; Sakai, M. (Toyohashi Univ. of Technology (Japan). Dept. of Materials Science)

1999-01-01

Uniaxial compressive creep tests with strain value up to -0.1 for a [beta]-spodumene glass ceramic are conducted at 1060 C. From the observation of microstructural changes between before and after the creep deformations, it is shown that the grain-boundary sliding takes place via cooperative movement of groups of grains rather than individual grains under the large-scale-deformation. The deformation process and the surface technique used in this work are not only applicable to explain the deformation and flow of two-phase ceramics but also the superplastic deformation. (orig.) 12 refs.

Congenital and acquired foot disorders and their roentgenographic examination

International Nuclear Information System (INIS)

Weber, M.

1986-01-01

In addition to general radiologic aspects there are special orthopedic considerations have in interpretation of X-rays of the foot. This is especially important for the diagnosis of orthopedic foot diseases. In clubfoot X-rays are useful for therapeutic planning and control. Even in the first months of life radiographs can show important disturbances of growth of the foot and displacement of the bones of the tarsus. In other congenital foot deformities X-rays are important for diagnostic reasons: they prove luxations or skeletal deformities. The most important acquired foot disease is the pronating foot. X-rays do not only show the amount of joint damage and structural changes of bones but also allow to draw conclusions to be drawn about the causes of static and dynamic changes of the foot skeleton. Functional diagnostic radiological investigation is of decisive importance for evaluation of infantile pronating foot. X-rays allow the differentiation to be made between physiological and pathologic changes. Subtle radiographic investigation is essential while planning operative treatment in childhood, as in adults. (orig.) [de

Analogue experiment of the crustal deformation by X-ray CT; X sen CT wo mochiita chikaku no henkei no analogue jikken

Energy Technology Data Exchange (ETDEWEB)

Nakajima, Y.; Shi, B; Murakami, Y. [Geological Survey of Japan, Tsukuba (Japan)

1997-05-27

This paper reports a predictive result on a deformation experiment on sand beds using an X-ray computerized tomography (CT) equipment. The X-ray CT is a method to perform the following processes: X-rays are irradiated on a sample; decayed intensity data are measured along ray paths of the permeated X-rays; the data are inverted by using the Fourier transform; and spatial distribution of the coefficient of X-ray absorption inside the sample is acquired as a gray scale image. The deformation experiment was carried by putting sand into an acrylic container to a depth of 2 cm and manually pressing a plate in the horizontal direction. Sand blocks make a relative motion along a specific plane when they are deformed, but it was not possible to recognize faults clearly by naked eyes. Upon completion of the deformation, the experimental device was placed on the CT equipment to acquire images of the two-dimensional cross section. The higher the X-ray absorption coefficient, the brighter the picture elements. It can be seen that three inversed faults have been imaged clearly. Therefore, this equipment was verified usable as an effective observation equipment for an analogue deformation experiment. 4 refs., 2 figs.

SU-E-J-241: Creation of Ventilation CT From Daily 4D CTs Or 4D Conebeam CTs Acquired During IGRT for Thoracic Cancers

International Nuclear Information System (INIS)

Tai, A; Ahunbay, E; Li, X

2014-01-01

Purpose: To develop a method to create ventilation CTs from daily 4D CTs or 4D KV conebeam CTs (4DCBCT) acquired during image-guided radiation therapy (IGRT) for thoracic tumors, and to explore the potential for using the ventilation CTs as a means for early detection of lung injury during radiation treatment. Methods: 4DCT acquired using an in-room CT (CTVision, Siemens) and 4DCBCT acquired using the X-ray Volume Imaging (XVI) system (Infinity, Elekta) for representative lung cancer patients were analyzed. These 4D data sets were sorted into 10 phase images. A newly-available deformable image registration tool (ADMIRE, Elekta) is used to deform the phase images at the end of exhale (EE) to the phase images at the end of inhale (EI). The lung volumes at EI and EE were carefully contoured using an intensity-based auto-contour tool and then manually edited. The ventilation images were calculated from the variations of CT numbers of those voxels masked by the lung contour at EI between the registered phase images. The deformable image registration is also performed between the daily 4D images and planning 4DCT, and the resulting deformable field vector (DFV) is used to deform the planning doses to the daily images by an in-house Matlab program. Results: The ventilation images were successfully created. The tide volumes calculated using the ventilation images agree with those measured through volume difference of contours at EE and EI, indicating the accuracy of ventilation images. The association between the delivered doses and the change of lung ventilation from the daily ventilation CTs is identified. Conclusions: A method to create the ventilation CT using daily 4DCTs or 4D KV conebeam CTs was developed and demonstrated

Simulation of Texture Evolution during Uniaxial Deformation of Commercially Pure Titanium

Science.gov (United States)

Bishoyi, B.; Debta, M. K.; Yadav, S. K.; Sabat, R. K.; Sahoo, S. K.

2018-03-01

The evolution of texture in commercially pure (CP) titanium during uniaxial tension and compression through VPSC (Visco-plastic self-consistent) simulation is reported in the present study. CP-titanium was subjected to both uniaxial tension and compression upto 35% deformation. During uniaxial tension, tensile twin of \\{10\\bar{1}2\\}\\unicode{x003C;}\\bar{1}011\\unicode{x003E;} type and compressive twin of \\{11\\bar{2}2\\}\\unicode{x003C;}11\\bar{2}\\bar{3}\\unicode{x003E;} type were observed in the samples. However, only tensile twin of \\{10\\bar{1}2\\}\\unicode{x003C;}\\bar{1}011\\unicode{x003E;} type and compressive twin of type was observed in the samples during uniaxial compression. Volume fractions of the twins were increased linearly as a function of percentage deformation during uniaxial tension. Whereas, during uniaxial compression the twinning volume fraction was increased up to 20% deformation and then decreased rapidly on further increasing the percentage deformation. During uniaxial tension, the general t-type textures were observed in the samples irrespective of the percentage deformation. The initial non-basal texture was oriented to split basal texture during uniaxial compression of the sample. VPSC formulation was used for simulating the texture development in the material. Different hardening parameters were estimated through correlating the simulated stress-strain curve with the experimental stress-strain data. It was observed that, prismatic slip \\{10\\bar{1}0\\}\\unicode{x003C;}11\\bar{2}0\\unicode{x003E;} operated as the primary deformation mode during uniaxial tension whereas basal slip \\{0001\\}\\unicode{x003C;}11\\bar{2}0\\unicode{x003E;} acquired the leading role during deformation through uniaxial compression. It was also revealed that active deformation modes were fully depending on percentage deformation, loading direction, and orientation of grains.

Combining variational and model-based techniques to register PET and MR images in hand osteoarthritis

International Nuclear Information System (INIS)

Magee, Derek; Tanner, Steven F; Jeavons, Alan P; Waller, Michael; Tan, Ai Lyn; McGonagle, Dennis

2010-01-01

Co-registration of clinical images acquired using different imaging modalities and equipment is finding increasing use in patient studies. Here we present a method for registering high-resolution positron emission tomography (PET) data of the hand acquired using high-density avalanche chambers with magnetic resonance (MR) images of the finger obtained using a 'microscopy coil'. This allows the identification of the anatomical location of the PET radiotracer and thereby locates areas of active bone metabolism/'turnover'. Image fusion involving data acquired from the hand is demanding because rigid-body transformations cannot be employed to accurately register the images. The non-rigid registration technique that has been implemented in this study uses a variational approach to maximize the mutual information between images acquired using these different imaging modalities. A piecewise model of the fingers is employed to ensure that the methodology is robust and that it generates an accurate registration. Evaluation of the accuracy of the technique is tested using both synthetic data and PET and MR images acquired from patients with osteoarthritis. The method outperforms some established non-rigid registration techniques and results in a mean registration error that is less than approximately 1.5 mm in the vicinity of the finger joints.

Microstructural change during creep deformation in a 10%Cr martensitic steel

International Nuclear Information System (INIS)

Kim, Sung Ho; Song, B. J.; Ryu, Woo Seog

2001-01-01

The relationship between creep deformation and microstructural changes in martensitic 10Cr-MoW steel has been studied. Transmission electron microscopy and image analyser were used to determine the variation of precipitates and martensite lath width size during creep deformation and aging. As precipitates are coarsened during creep deformation, dislocations become easy to move and the recovery proceeds rapidly. This leads to the growth of lath width. The average size of precipitates was linearly increased with creep time. On the other hand the growth rate of lath width is constant until tertiary creep, but the growth of lath width is accelerated during tertiary creep. It has been concluded that the growth behavior of lath width are consistent with creep deformation. Because the growth of lath width is controlled by the coarsening of precipitates it is important to form more stable precipitates in creep condition for improvement of creep properties of martensitic steel. Microstructure of martensitic steel is thermally very stable, so the size of precipitates and martensite lath width are hardly changed during aging

Measuring co-seismic deformation of the Sichuan earthquake by satellite differential INSAR

Science.gov (United States)

Zhang, Yonghong; Gong, Wenyu; Zhang, Jixian

2008-12-01

The Sichuan Earthquake, occurred on May 12, 2008, is the strongest earthquake to hit China since the 1976 Tangshan earthquake. The earthquake had a magnitude of M 8.0, and caused surface deformation greater than 3 meters. This paper presents the research work of measuring the co-seismic deformations of the earthquake with satellite differential interferometric SAR technique. Four L-band SAR images were used to form the interferogram with 2 pre- scenes imaged on Feb 17, 2008 and 2 post- scenes on May 19, 2008. The Digital Elevation Models extracted from 1:50,000-scale national geo-spatial database were used to remove the topographic contribution and form a differential interferogram. The interferogram presents very high coherence in most areas, although the pre- and post- images were acquired with time interval of 92 days. This indicates that the L-band PALSAR sensor is very powerful for interferometry applications. The baseline error is regarded as the main phase error source in the differential interferogram. Due to the difficulties of doing field works immediately after the earthquake, only one deformation measurement recorded by a permanent GPS station is obtained for this research. An approximation method is proposed to eliminate the orbital phase error with one control point. The derived deformation map shows similar spatial pattern and deformation magnitude compared with deformation field generated by seismic inversion method.

Estimation of Surface Deformation due to Pasni Earthquake Using SAR Interferometry

Science.gov (United States)

Ali, M.; Shahzad, M. I.; Nazeer, M.; Kazmi, J. H.

2018-04-01

Earthquake cause ground deformation in sedimented surface areas like Pasni and that is a hazard. Such earthquake induced ground displacements can seriously damage building structures. On 7 February 2017, an earthquake with 6.3 magnitudes strike near to Pasni. We have successfully distinguished widely spread ground displacements for the Pasni earthquake by using InSAR-based analysis with Sentinel-1 satellite C-band data. The maps of surface displacement field resulting from the earthquake are generated. Sentinel-1 Wide Swath data acquired from 9 December 2016 to 28 February 2017 was used to generate displacement map. The interferogram revealed the area of deformation. The comparison map of interferometric vertical displacement in different time period was treated as an evidence of deformation caused by earthquake. Profile graphs of interferogram were created to estimate the vertical displacement range and trend. Pasni lies in strong earthquake magnitude effected area. The major surface deformation areas are divided into different zones based on significance of deformation. The average displacement in Pasni is estimated about 250 mm. Maximum pasni area is uplifted by earthquake and maximum uplifting occurs was about 1200 mm. Some of areas was subsidized like the areas near to shoreline and maximum subsidence was estimated about 1500 mm. Pasni is facing many problems due to increasing sea water intrusion under prevailing climatic change where land deformation due to a strong earthquake can augment its vulnerability.

Spinal deformities rehabilitation - state of the art review

Directory of Open Access Journals (Sweden)

Weiss Hans-Rudolf

2010-12-01

Full Text Available Abstract Background Medical rehabilitation aims at an improvement in function, capacity and participation. For the rehabilitation of spinal deformities, the goal is to maintain function and prevent secondary symptoms in the short- and long-term. In patients with scoliosis, predictable signs and symptoms include pain and reduced pulmonary function. Materials and methods A Pub Med review was completed in order to reveal substantial evidence for inpatient rehabilitation as performed in Germany. No evidence has been found in general to support claims for actual inpatient rehabilitation programmes as used today. Nevertheless, as there is some evidence that inpatient rehabilitation may be beneficial to patients with spinal deformities complicated by certain additional conditions, the body of evidence there is for conservative treatment of spinal deformities has been reviewed in order to allow suggestions for outpatient conservative treatment and inpatient rehabilitation. Discussion Today, for both children and adolescents, we are able to offer intensive rehabilitation programmes lasting three to five days, which enable the patients to acquire the skills necessary to prevent postures fostering scoliosis in everyday life without missing too much of school teaching subjects at home. The secondary functional impairments adult scoliosis patients might have, as in the opinion of the author, still today require the time of 3-4 weeks in the clinical in-patient setting. Time to address psychosocial as well as somatic limitations, namely chronic pains and cardiorespiratory malfunction is needed to preserve the patients working capability in the long-term. Conclusion Outpatient treatment/rehabilitation is sufficient for adolescents with spinal deformities. Inpatient rehabilitation is recommended for patients with spinal deformities and pain or severe restrictive ventilation disorder.

Three saints with deformed extremities in an Italian Renaissance altarpiece.

Science.gov (United States)

Albury, W R; Weisz, G M

2017-03-01

A fifteenth-century Florentine altarpiece painted by the Pollaiuolo brothers, Antonio (1433-1498) and Piero (1443-1496), shows three saints with evident deformities of the hands and feet. The pathologies concerned are tentatively identified, and various rationales for their presence in the painting are discussed. Of particular importance is the location of the altarpiece in a chapel which houses the tomb of the Cardinal of Portugal, Prince James of Lusitania (1433-1459). It is argued that both the artistic style of the day and the religious symbolism of the Cardinal's funeral chapel contributed to the artists' decision to portray the saints with deformities. An unnatural curvature of the fifth finger was apparently considered elegant in fifteenth-century paintings, and the depiction of bare feet with hallux valgus gave them a shape which approximated and could have been caused by fashionable pointed shoes. But in addition, deformities in religious art could be symbolic of suffering and martyrdom, a theme which the Cardinal's chapel emphasised in a number of ways. It is suggested therefore that the Pollaiuolo altarpiece reconciles these two disparate factors, portraying genuine deformities in a way that was artistically stylish and symbolically meaningful.

Sports Injury-Related Fingers and Thumb Deformity Due to Tendon or Ligament Rupture

Directory of Open Access Journals (Sweden)

Rong-Jie Bai

2018-01-01

Conclusions: Sports injury-related fingers and thumb deformity are relatively common. MRI is an accurate method for evaluation of the anatomy and pathologic conditions of the fingers and thumb. It is a useful tool for accurate diagnosis of the sports-related ligaments and tendons injuries in hand.

An Efficient Solution for Hand Gesture Recognition from Video Sequence

Directory of Open Access Journals (Sweden)

PRODAN, R.-C.

2012-08-01

Full Text Available The paper describes a system of hand gesture recognition by image processing for human robot interaction. The recognition and interpretation of the hand postures acquired through a video camera allow the control of the robotic arm activity: motion - translation and rotation in 3D - and tightening/releasing the clamp. A gesture dictionary was defined and heuristic algorithms for recognition were developed and tested. The system can be used for academic and industrial purposes, especially for those activities where the movements of the robotic arm were not previously scheduled, for training the robot easier than using a remote control. Besides the gesture dictionary, the novelty of the paper consists in a new technique for detecting the relative positions of the fingers in order to recognize the various hand postures, and in the achievement of a robust system for controlling robots by postures of the hands.

Semiautomated four-dimensional computed tomography segmentation using deformable models

International Nuclear Information System (INIS)

Ragan, Dustin; Starkschall, George; McNutt, Todd; Kaus, Michael; Guerrero, Thomas; Stevens, Craig W.

2005-01-01

The purpose of this work is to demonstrate a proof of feasibility of the application of a commercial prototype deformable model algorithm to the problem of delineation of anatomic structures on four-dimensional (4D) computed tomography (CT) image data sets. We acquired a 4D CT image data set of a patient's thorax that consisted of three-dimensional (3D) image data sets from eight phases in the respiratory cycle. The contours of the right and left lungs, cord, heart, and esophagus were manually delineated on the end inspiration data set. An interactive deformable model algorithm, originally intended for deforming an atlas-based model surface to a 3D CT image data set, was applied in an automated fashion. Triangulations based on the contours generated on each phase were deformed to the CT data set on the succeeding phase to generate the contours on that phase. Deformation was propagated through the eight phases, and the contours obtained on the end inspiration data set were compared with the original manually delineated contours. Structures defined by high-density gradients, such as lungs, cord, and heart, were accurately reproduced, except in regions where other gradient boundaries may have confused the algorithm, such as near bronchi. The algorithm failed to accurately contour the esophagus, a soft-tissue structure completely surrounded by tissue of similar density, without manual interaction. This technique has the potential to facilitate contour delineation in 4D CT image data sets; and future evolution of the software is expected to improve the process

[Advances in the research of prevention and treatment of postburn contractures of hand].

Science.gov (United States)

Wang, K A; Wu, G S; Sun, Y; Xia, Z F

2017-01-20

Scar contracture deformity, which can lead to dysfunction of hand and low quality of life, is one of the common complication after hand burns. The prevention measures of scar contracture after hand burns include large skin grafting, prevention of infection, insistence on wearing pressure gloves, use of silicone sheets, wearing orthosis, accepting proper physical therapy, and early functional exercise. The primary treatments of postburn contractures of the hand are surgery, drugs, laser treatment, and rehabilitation therapy. Excision of scars, release of muscle, joints or bones, and soft tissue transplantation are the core of surgery. Laser treatment has a bright future but still needs to be further studied. Additionally, some novel treatments such as molecular targeted therapy, cell therapy, fat injection, and botulinum toxin injection will play important roles in prevention and treatment of postburn contractures in the future. The purpose of this article is to review the literature concerning postburn contractures of the hand, and summarize the present situation of prevention and treatment of such disease comprehensively.

THE OCCURRENCE OF THE RADIAL CLUB HAND IN CHILDREN WITH DIFFERENT SYNDROMES

Directory of Open Access Journals (Sweden)

Sergey Ivanovich Golyana

2013-03-01

Full Text Available Radial club hand is a developmental anomaly of the upper extremity, being characterized as a longitudinal underdevelopment of a forearm and a hand on the radial surface, consisting in a hypo-/ aplazy radial bone and the thumb of various degree of expressiveness. Characteristic symptoms of this developmental anomaly are: shortening and bow-shaped curvature of a forearm, palmar and radial deviation of a hand, underdevelopment of the thumb from its proximal departments and structures, anomaly of development of three-phalanx fingers of a hand (is more often than the 2-4th, violation of a cosmetic condition and functionality of the affected segment. From 2000 for 2012 in FSI SRICO n.a. H.Turner examination and treatment of 23 children with various syndromes at which the radial club hand was revealed are conducted. The main syndromes at which it is revealed radial club hand - Holt-Orama syndrome, TAR- syndrome and VACTERL syndrome. Tactics and techniques of surgical treatment of a radial club hand it various syndromes most often don’t differ from treatment of other types of a radial club hand though demand an individual approach depending on severity and a type of deformation of the upper extremity.

Interventions to improve patient hand hygiene: a systematic review.

Science.gov (United States)

Srigley, J A; Furness, C D; Gardam, M

2016-09-01

Nosocomial pathogens may be acquired by patients via their own unclean hands, but there has been relatively little emphasis on patient hand hygiene as a tool for preventing healthcare-associated infections (HCAIs). The aim of this systematic review was to determine the efficacy of patient hand hygiene interventions in reducing HCAIs and improving patient hand hygiene rates compared to usual care. Electronic databases and grey literature were searched to August 2014. Experimental and quasi-experimental studies were included if they evaluated a patient hand hygiene intervention conducted in an acute or chronic healthcare facility and included HCAI incidence and/or patient hand hygiene rates as an outcome. All steps were performed independently by two investigators. Ten studies were included, most of which were uncontrolled before-after studies (N=8). The majority of interventions (N=7) were multi-modal, with components similar to healthcare worker hand hygiene programmes, including education, reminders, audit and feedback, and provision of hand hygiene products. Six studies reported HCAI outcomes and four studies assessed patient hand hygiene rates; all demonstrated improvements but were at moderate to high risk of bias. In conclusion, interventions to improve patient hand hygiene may reduce the incidence of HCAIs and improve hand hygiene rates, but the quality of evidence is low. Future studies should use stronger designs and be more selective in their choice of outcomes. Copyright © 2016 The Healthcare Infection Society. Published by Elsevier Ltd. All rights reserved.

Exact reconstruction in 2D dynamic CT: compensation of time-dependent affine deformations

International Nuclear Information System (INIS)

Roux, Sebastien; Desbat, Laurent; Koenig, Anne; Grangeat, Pierre

2004-01-01

This work is dedicated to the reduction of reconstruction artefacts due to motion occurring during the acquisition of computerized tomographic projections. This problem has to be solved when imaging moving organs such as the lungs or the heart. The proposed method belongs to the class of motion compensation algorithms, where the model of motion is included in the reconstruction formula. We address two fundamental questions. First what conditions on the deformation are required for the reconstruction of the object from projections acquired sequentially during the deformation, and second how do we reconstruct the object from those projections. Here we answer these questions in the particular case of 2D general time-dependent affine deformations, assuming the motion parameters are known. We treat the problem of admissibility conditions on the deformation in the parallel-beam and fan-beam cases. Then we propose exact reconstruction methods based on rebinning or sequential FBP formulae for each of these geometries and present reconstructed images obtained with the fan-beam algorithm on simulated data

Deformation localization at the tips of shear fractures: An analytical approach

Science.gov (United States)

Misra, Santanu

2011-04-01

Mechanical heterogeneities are important features in rocks which trigger deformation localization in brittle, ductile or brittle-ductile modes during deformation. In a recent study Misra et al. (2009) have investigated these different processes of deformation localization at the tips of pre-existing planar shear fractures. The authors identified four mechanisms of deformation, ranging from brittle to ductile, operating at the crack tips. Mechanism A: brittle deformation is the dominant process that forms a pair of long tensile fractures at the two crack tips. Mechanism B: nature of deformation is mixed where the tensile fractures grow to a finite length with incipient plastic deformation at the tips. Mechanism C: mixed mode deformation characterized by dominating macro-scale shear bands, and short, opened-out tensile fissures. Mechanism D: localization of plastic bands in the form of a pair of shear bands at each tip without any discernible brittle fracturing. The transition of the mechanisms is a function of orientation ( α) of the crack with respect to the bulk compression direction and the finite length ( l) of the crack. The aim of this study is to present a theoretical analysis to account for the variability of deformation localization in the vicinity of pre-existing shear cracks considering an elastic-plastic rheological model. The analysis calculates the principal tensile stress ( σ1) and the second stress invariant ( I2) of the stress field at the fracture tip to explain the transition from Mechanism A (tensile fracturing) to Mechanism D (ductile strain). The results show that σ1 at the fracture tip increases non-linearly with increasing α and Ar (aspect ratio of the shear crack), and assumes a large value when α > 50 o, promoting tensile fractures. On the other hand, I2 is a maximum at α < 45°, resulting in nucleation of ductile shear bands.

Semmelweis revisited: hand hygiene and nosocomial disease transmission in the anesthesia workstation.

Science.gov (United States)

Biddle, Chuck

2009-06-01

Hospital-acquired infections occur at an alarmingly high frequency, possibly affecting as many as 1 in 10 patients, resulting in a staggering morbidity and an annual mortality of many tens of thousands of patients. Appropriate hand hygiene is highly effective and represents the simplest approach that we have to preventing nosocomial infections. The Agency for Healthcare Research and Quality has targeted hand-washing compliance as a top research agenda item for patient safety. Recent research has identified inadequate hand washing and contaminated anesthesia workstation issues as likely contributors to nosocomial infections, finding aseptic practices highly variable among providers. It is vital that all healthcare providers, including anesthesia providers, appreciate the role of inadequate hand hygiene in nosocomial infection and meticulously follow the mandates of the American Association of Nurse Anesthetists and other professional healthcare organizations.

Effects of Dexterity Level and Hand Anthropometric Dimensions on Smartphone Users’ Satisfaction

Directory of Open Access Journals (Sweden)

N. Firat Ozkan

2015-01-01

Full Text Available The usage of smartphones instead of simple mobile phones increases sharply in our era, especially among young people, because they do multiple tasks with single equipment. This study mainly focuses on smartphone satisfaction by combining hand measurements, smartphone users’ survey results, and hand dexterity levels of corresponding users acquired from Minnesota Manual Dexterity Test (MMDT. Structural Equation Modelling (SEM is used as a statistical tool to discover the potential direct and indirect relations among user satisfaction, hand dimensions, and dexterity scores. Results indicates that thumb length, hand length, and dexterity level of the users have notable effects on users’ satisfaction with smartphones. Based on the results, a new approach that includes both gross motor skills and physical measurements is suggested to see hidden indirect relations with satisfaction.

Treatment of wrist deformities in children with arthrogryposis multiplex congenita

Directory of Open Access Journals (Sweden)

Evgeniya A Kochenova

2016-03-01

Conclusions: Patients with segmental lesions of the spinal cord at the С6-С7 and С5-С8 level were associated with restoration of active wrist extension up to the neutral position or more and were expected to achieve significant improvement of hand function. Patients with spinal cord lesions at the C5-Th1 level exhibited significant lesions of the muscles, along with bone deformities. Consequently, surgical treatment could only achieve functional wrist position with minimal improvement of hand function. Using differential approaches in the treatment of wrist contracture that are selected by determining the level of spinal cord lesion will enable physicians to predict the outcome and improve the function and appearance of the wrist.

Grasping and manipulation of deformable objects based on internal force requirements

Directory of Open Access Journals (Sweden)

Sohil Garg

2008-11-01

Full Text Available In this paper an analysis of grasping and manipulation of deformable objects by a three finger robot hand has been carried out. It is proved that the required fingertip grasping forces and velocities vary with change in object size due to deformation. The variation of the internal force with the change in fingertip and object contact angle has been investigated in detail. From the results it is concluded that it is very difficult to manipulate an object if the finger contact angle is not between 30 o and 70 o, as the internal forces or velocities become very large outside this range. Hence even if the object is inside the work volume of the three fingers it would still not be possible to manipulate it. A simple control model is proposed which can control the grasping and manipulation of a deformable object. Experimental results are also presented to prove the proposed method.

Congenital malformations of hands and feet in Smith-Lemli-Opitz syndrome

Directory of Open Access Journals (Sweden)

N. A. Kovalenko-Klychkova

2013-01-01

Full Text Available Smith-Lemli-Opitz syndrome is rare genetic disorder with multiple limb malformations and neurological manifestation, caused by inborn defect of cholesterol metabolism. Congenital deformities of feet and hands are most common orthopedic symptoms in this syndrome. Description of a girl with Smith-Lemli-Opitz syndrome demonstrates specific features of this disorder and emphasize the importance of proper interpretation of orthopedic malformations for early diagnosis of genetic conditions.

[Beliefs - Misbeliefs, answering essential questions about hand hygiene from the view of the evidences].

Science.gov (United States)

Szél, Borbála; Nagy, Kamilla; Milassin, Márta; Tálosi, Gyula

2017-02-01

Contaminated hands can play pivotal role in the development and spread of healthcare-associated infections. Consequently hand hygiene practice performed with adequate technique and with adequate timing is an essential implement for patient safety. Inhibition of the practice of high level hand hygiene by the misconceptions or deficient knowledge of healthcare workers may lead to negative influence on the quality of patient care. Erroneous beliefs or "rumourous knowledge" acquired from colleagues can not only influence the attitude of healthcare workers, but can also give rise to insufficient hand hygiene compliance. Finding, interpreting and imparting the related evidence by delivering continuing education and lectures, highlighting the theoretical and practical know-how on hand hygiene could help to understand and imprint the evidence-based practice and adequate technique in the essential issue of hand hygiene. Orv. Hetil., 2017., 158(6), 212-219.

The diagnostic significance of the radiologic appearances of the hands in systemic lupus erythematosus (SLE)

International Nuclear Information System (INIS)

Winkler, P.; Baenkler, H.W.; Pfuhl, E.; Gutmann, W.

1980-01-01

40 patients with SLE were assessed, the diagnoses being made according to modified ARA-criteria; the hand films of 25 of these patients were analysed. The most important roentgenologic findings consisted of reducible deformities with mild or absent articular changes in the deformed MCP and PIP joints. As these changes often occur late in the course of SLE, a primary radiological diagnosis was possible in only three cases (8%), whereas hand films provided confirmatory evidence of disease in a further seven patients. These roentgenological characteristics of SLE were found significantly less often in patients with definite RA; this group tended to have positive ANF (antinuclear factors). Antibodies against DNA may be absent, especially in a less active phase of disease. ANF is non-specific, and SLE simulates RA in 10-20% of cases. It is, therefore, very important in individual cases to consider the diagnosis of SLE in the presence of deformity without corresponding articular changes. Direct comparison of both the p.a. and oblique views is essential in the evaluation of reducible deformities, although this point has not been stressed in the literature. Reducible deformities may be overlooked in physical examination, when the patient gives no history of functional disability. The main differential diagnosis is Jaccoud's arthropathy, which is rarely seen in a general hospital. Most of these patients give a history of recurrent rheumatic fever, a minority complain about joint pain or disability, approximately 90% show signs indicating a valvular lesion of the heart, over 75% have a normal ESR and a positive rheumatoid or antinuclear factor is very rarely found. The distinction from SLE or rheumatoid arthritis is therefore easily established on additional non-radiological criteria. (orig./MG) [de

Competing Grain Boundary and Interior Deformation Mechanisms with Varying Sizes

Energy Technology Data Exchange (ETDEWEB)

Zhang, Wei [University of Tennessee (UT); Gao, Yanfei [ORNL; Nieh, T. G. [University of Tennessee, Knoxville (UTK)

2018-01-01

In typical coarse-grained alloys, the dominant plastic deformations are dislocation gliding or climbing, and material strengths can be tuned by dislocation interactions with grain boundaries, precipitates, solid solutions, and other defects. With the reduction of grain size, the increase of material strengths follows the classic Hall-Petch relationship up to nano-grained materials. Even at room temperatures, nano-grained materials exhibit strength softening, or called the inverse Hall-Petch effect, as grain boundary processes take over as the dominant deformation mechanisms. On the other hand, at elevated temperatures, grain boundary processes compete with grain interior deformation mechanisms over a wide range of the applied stress and grain sizes. This book chapter reviews and compares the rate equation model and the microstructure-based finite element simulations. The latter explicitly accounts for the grain boundary sliding, grain boundary diffusion and migration, as well as the grain interior dislocation creep. Therefore the explicit finite element method has clear advantages in problems where microstructural heterogeneities play a critical role, such as in the gradient microstructure in shot peening or weldment. Furthermore, combined with the Hall-Petch effect and its breakdown, the above competing processes help construct deformation mechanism maps by extending from the classic Frost-Ashby type to the ones with the dependence of grain size.

Improving hand hygiene in a paediatric hospital: a multimodal quality improvement approach.

Science.gov (United States)

Jamal, Ahmed; O'Grady, G; Harnett, E; Dalton, D; Andresen, D

2012-02-01

Effective hand hygiene has long been recognised as an important way to reduce the transmission of bacterial and viral pathogens in healthcare settings. However, many studies have shown that adherence to hand hygiene remains low, and improvement efforts have often not delivered sustainable results. The Children's Hospital at Westmead is the largest tertiary paediatric hospital in Sydney, Australia. The hospital participated in a state-wide 'Clean hands save lives' campaign which was initiated in 2006. Strong leadership, good stakeholder engagement, readily accessible alcohol-based hand rub at the point of patient care, a multifaceted education programme, monitoring of staff, adherence to recommended hand hygiene practices and contemporaneous feedback of performance data have significantly improved and maintained compliance with hand hygiene. Hand hygiene compliance has increased from 23% in 2006 to 87% in 2011 (phand hygiene has been evident in the last 4 years. A decline in a set of hospital-acquired infections (including rotavirus, multiresistant organism transmission, and nosocomial bacteraemia) has also been noted as hand hygiene rates have improved. Monthly usage of alcohol-based hand rub has increased from 16 litres/1000 bed days to 51 litres/1000 bed days during this same period. This project has delivered sustained improvement in hand hygiene compliance by establishing a framework of multimodal evidence-based strategies.

Custom-made silicone hand prosthesis: A case study.

Science.gov (United States)

Nayak, S; Lenka, P K; Equebal, A; Biswas, A

2016-09-01

Up to now, a cosmetic glove was the most common method for managing transmetacarpal (TMC) and carpometacarpal (CMC) amputations, but it is devoid of markings and body color. At this amputation level, it is very difficult to fit a functional prosthesis because of the short available length, unsightly shape, grafted skin, contracture and lack of functional prosthetic options. A 30-year-old male came to our clinic with amputation at the 1st to 4th carpometacarpal level and a 5th metacarpal that was projected laterally and fused with the carpal bone. The stump had grafted skin, redness, and an unhealed suture line. He complained of pain projected over the metacarpal and suture area. The clinical team members decided to fabricate a custom-made silicone hand prosthesis to accommodate the stump, protect the grafted skin, improve the hand's appearance and provide some passive function. The custom silicone hand prosthesis was fabricated with modified flexible wires to provide passive interphalangeal movement. Basic training, care and maintenance instructions for the prosthesis were given to the patient. The silicone hand prosthesis was able to restore the appearance of the lost digits and provide some passive function. His pain (VAS score) was reduced. Improvement in activities of daily living was found in the DASH questionnaire and Jebsen-Taylor Hand Function test. A silicone glove is a good option for more distal amputations, as it can accommodate any deformity, protect the skin, enhance the appearance and provide functional assistance. This case study provides a simple method to get passively movable fingers after proximal hand amputation. Copyright © 2016. Published by Elsevier Masson SAS.

Differences in the cyclic deformation behaviour of quenched and tempered steel 42 CrMo 4 (AISI 4140) due to stress- and strain-control

International Nuclear Information System (INIS)

Schulze, V.; Lang, K.-H.; Voehringer, O.; Macherauch, E.

1998-01-01

Cyclic stress-strain-curves and Manson-Coffin-plots of quenched and tempered steel 42 CrMo 4 (AISI 4140) strongly depend on whether they are determined under stress- or total-strain-control. At total-strain-controlled experiments, this is caused on the one hand by comparatively high initial stress-amplitudes which lead to distinctive cyclic work softening. On the other hand, the occuring differences in the evolution of inhomogeneous deformation patterns at both types of loading, which can be recorded by means of photoelasticity and microscopy, lead to differently distributed plastic deformations and to different integral values of plastic strain. (orig.)

Multiple intramedullary nailing of proximal phalangeal fractures of hand

Directory of Open Access Journals (Sweden)

Patankar Hemant

2008-01-01

Full Text Available Background: Proximal phalangeal fractures are commonly encountered fractures in the hand. Majority of them are stable and can be treated by non-operative means. However, unstable fractures i.e. those with shortening, displacement, angulation, rotational deformity or segmental fractures need surgical intervention. This prospective study was undertaken to evaluate the functional outcome after surgical stabilization of these fractures with joint-sparing multiple intramedullary nailing technique. Materials and Methods: Thirty-five patients with 35 isolated unstable proximal phalangeal shaft fractures of hand were managed by surgical stabilization with multiple intramedullary nailing technique. Fractures of the thumb were excluded. All the patients were followed up for a minimum of six months. They were assessed radiologically and clinically. The clinical evaluation was based on two criteria. 1. total active range of motion for digital functional assessment as suggested by the American Society for Surgery of Hand and 2. grip strength. Results: All the patients showed radiological union at six weeks. The overall results were excellent in all the patients. Adventitious bursitis was observed at the point of insertion of nails in one patient. Conclusion: Joint-sparing multiple intramedullary nailing of unstable proximal phalangeal fractures of hand provides satisfactory results with good functional outcome and fewer complications.

Postural & striatal deformities in Parkinson`s disease: Are these rare?

Directory of Open Access Journals (Sweden)

Sanjay Pandey

2016-01-01

Full Text Available Parkinson`s disease (PD is the most common neurodegenerative disease and is characterized by tremor, rigidity and akinesia. Diagnosis is clinical in the majority of the patients. Patients with PD may have stooped posture but some of them develop different types of postural and striatal deformities. Usually these deformities are more common in atypical parkinsonian disorders such as progressive supranuclear palsy and multisystem atrophy. But in many studies it has been highlighted that these may also be present in approximately one third of PD patients leading to severe disability. These include antecollis or dropped head, camptocormia, p0 isa syndrome, scoliosis, striatal hands and striatal toes. The pathogenesis of these deformities is a complex combination of central and peripheral influences such as rigidity, dystonia and degenerative skeletal changes. Duration of parkinsonism symptoms is an important risk factor and in majority of the patients these deformities are seen in advanced statge of the disease. The patients with such symptoms may initially respond to dopaminergic medications but if not intervened they may become fixed and difficult to treat. Pain and restriction of movement are most common clinical manifestations and these may mimick symptoms of musculoskeletal disorders like rheumatoid arthritis. Early diagnosis is important as the patients may respond to adjustment in dopaminergic medications. Recent advances such as deep brain stimulation (DBS and ultrasound guided botulinum toxin injection are helpful in management of these deformities in patients with PD.

Political Left and Right: Our Hands-On Logic

OpenAIRE

Frits Bienfait; Walter E. A. van Beek

2014-01-01

The origins and immediate vitality of the left/right divide which emerged in French revolutionary politics from 1789 can only be understood against the background of a much older classification dynamic based on the primacy of the right hand, first described by Robert Hertz in 1909. This dynamic infused political thinking first in Versailles and since 1815 in democracies throughout the world. In the process, the classical left/right polarity acquired a new dimension: the complementary notions ...

Habit tic nail deformity - a rare presentation in an 8 year old boy.

Science.gov (United States)

El-Heis, S; Abadie, Al

2016-11-15

Habit tic nail deformity is a nail dystrophy resulting from habitual, repetitive trauma to the nail. It is usually acquired in adulthood, however, we report a case of habit tic nail deformity in an 8 year old boy. The diagnosis was made clinically with further history revealing that the boy repeatedly rubbed his thumbnails and pushed the cuticles. Emollient cream (Balneum®) was recommended twice daily and both the patient and his mother were educated on the behavioral nature of this condition. There was marked improvement at 6 months of treatment and further improvement at 12 months.We note that habit tic nail deformity is not exclusive to adults. Diagnosis can be made clinically. History and physical examination provide valuable clues and psychosocial links must be explored and addressed. Management is challenging and compliance with treatment is variable. Patient education, barrier methods, and behavioral therapy can be helpful in preventing further trauma to the nails.

The art and science of photography in hand surgery.

Science.gov (United States)

Wang, Keming; Kowalski, Evan J; Chung, Kevin C

2014-03-01

High-quality medical photography plays an important role in teaching and demonstrating the functional capacity of the hands as well as in medicolegal documentation. Obtaining standardized, high-quality photographs is now an essential component of many surgery practices. The importance of standardized photography in facial and cosmetic surgery has been well documented in previous studies, but no studies have thoroughly addressed the details of photography for hand surgery. In this paper, we provide a set of guidelines and basic camera concepts for different scenarios to help hand surgeons obtain appropriate and informative high-quality photographs. A camera used for medical photography should come equipped with a large sensor size and an optical zoom lens with a focal length ranging anywhere from 14 to 75 mm. In a clinic or office setting, we recommend 6 standardized views of the hand and 4 views for the wrist; additional views should be taken for tendon ruptures, nerve injuries, or other deformities of the hand. For intraoperative pictures, the camera operator should understand the procedure and pertinent anatomy in order to properly obtain high-quality photographs. When digital radiographs are not available and radiographic film must be photographed, it is recommended to reduce the exposure and change the color mode to black and white to obtain the best possible pictures. The goal of medical photography is to present the subject in an accurate and precise fashion. Copyright © 2014 American Society for Surgery of the Hand. Published by Elsevier Inc. All rights reserved.

[Symptoms. Localizations: knee, hip, hands, spine, other localizations].

Science.gov (United States)

Pérez Martín, Álvaro

2014-01-01

The symptoms of osteoarthritis vary widely from patient to patient, depending especially on the localization on the disease. There is a poor correlation between radiological involvement and pain. In general, symptom onset is gradual and symptoms increase slowly but progressively. The most commonly affected joints are the knees, hips, hands, and spine. The main signs and symptoms are pain, stiffness, joint deformity, and crepitus. Pain is mechanical and its causes are multifactorial; in the initial phases, pain usually manifests in self-limiting episodes but may subsequently be almost constant. The criteria of the American college of Rheumatology for the classification of osteoarthritis of the knee, hip and hands are an aid to classification and standardization but are not useful for diagnosis. Hip osteoarthritis usually produces inguinal pain in the internal and anterior sections of the muscle extending to the knee and, with progression, tends to limit mobility. Knee osteoarthritis is more frequent in women and is usually associated with hand osteoarthritis and obesity. In hand osteoarthritis, the most commonly affected joints are the distal interphalangeal joints, followed by the proximal interphalangeal joints and the trapeziometacarpal joints; the development of Heberden and Bouchard nodes is common; involvement of the trapeziometacarpal joint is called rhizarthrosis and is one of the forms of osteoarthritis that produces the greatest limitation on hand function. Osteoarthritis of the spine affects the facet joints and the vertebral bodies. Other, less frequent, localizations are the foot, elbow and shoulder, which are generally secondary forms of osteoarthritis. Copyright © 2014 Elsevier España, S.L. All rights reserved.

An Enhanced Intelligent Handheld Instrument with Visual Servo Control for 2-DOF Hand Motion Error Compensation

Directory of Open Access Journals (Sweden)

Yan Naing Aye

2013-10-01

Full Text Available The intelligent handheld instrument, ITrem2, enhances manual positioning accuracy by cancelling erroneous hand movements and, at the same time, provides automatic micromanipulation functions. Visual data is acquired from a high speed monovision camera attached to the optical surgical microscope and acceleration measurements are acquired from the inertial measurement unit (IMU on board ITrem2. Tremor estimation and canceling is implemented via Band-limited Multiple Fourier Linear Combiner (BMFLC filter. The piezoelectric actuated micromanipulator in ITrem2 generates the 3D motion to compensate erroneous hand motion. Preliminary bench-top 2-DOF experiments have been conducted. The error motions simulated by a motion stage is reduced by 67% for multiple frequency oscillatory motions and 56.16% for pre-conditioned recorded physiological tremor.

An instrumented object for hand exercise and assessment using a pneumatic pressure sensor

Science.gov (United States)

Mohan, A.; Tharion, G.; Kumar, R. K.; Devasahayam, S. R.

2018-05-01

Measurement of grip force is important for both exercise training and assessment of the hand during physical rehabilitation. The standard method uses a grip dynamometer which measures the force between the fingers and opposing thumb. The primary limitation of the grip dynamometer is the restriction of measurement to cylindrical grasps. Any deformation of the hand due to muscular or skeletal disease makes the grip dynamometer difficult or impossible to use. An alternative to the grip dynamometer is a sealed pneumatic object that can be gripped by the hand. Measurement of the internal pressure in the object can be related to the grip force. In this paper, we analyze such a pneumatic pressure sensing object for hand grip assessment and also describe an easy fabrication of the grip sensor. The instrumented object presented in this paper is designed to assess both the maximal voluntary grip forces and continuous grip force to monitor control of hand function during exercise under instruction from a therapist. Potential uses of such a pneumatic pressure sensing object for hand grip are in physical rehabilitation of patients following paralysing illnesses like stroke and spinal cord injury.

Effect of Sn addition on the microstructure and deformation behavior of Mg-3Al alloy

International Nuclear Information System (INIS)

Suh, Byeong-Chan; Kim, Jae H.; Bae, Jun Ho; Hwang, Ji Hyun; Shim, Myeong-Shik; Kim, Nack J.

2017-01-01

Mg alloys generally suffer from their poor formability at low temperatures due to their strong basal texture and a lack of adequate deformation systems. In the present study, a small amount of Sn was added instead of Zn to Mg-3Al alloy to modify its deformation behavior and improve the stretch formability. Microstructural examinations of the deformed Mg-3Al-1Sn (AT31) alloy by electron backscatter diffraction and transmission electron microscopy show that prismatic slip is quite active during deformation, resulting in much lower r-values and planar anisotropy than the counterpart Mg-3Al-1Zn (AZ31) alloy. Polycrystal plasticity simulation based on visco-plasticity self-consistent (VPSC) model also shows that prismatic slip is the dominant deformation mode in AT31 alloy besides basal slip. As a consequence, AT31 alloy shows a much higher stretch formability than AZ31 alloy. On the other hand, AZ31 alloy shows the development of intense shear bands during stretch forming, and these shear bands act as crack propagating paths, limiting the stretch formability of AZ31 alloy.

Dupuytren’s contracture of hand and its medical and social review

Directory of Open Access Journals (Sweden)

V. O. Vishnevskiy

2014-02-01

Full Text Available Introduction Dupuytren's contracture is a disease of connective tissue with the affection of palmar aponeurosis, frequently with chronic recurrent course, the flexion deformities of fingers and dysfunction of the hand. It composed 11,8 % among of all types of the hand pathology. The mostly it develops in men of middle-aged and elderly. At young age it occurs more rarely, but with fast progressing current, which in 67 % of cases leads to impaired ability to perform professional hand-work and in 3 % patients to physical inability. Predisposing factors for this fibromatosis are numerous, but one of the popular opinion among of authors is a hereditary character of disease. In clinical practice, the most frequently used fourth degree’s classification of Dupuytren's contracture includes severity of deformation and function disorders of the hand. It is correspond to the normative standards of medical and social expertise The aim of research: to specify the most optimal methods of surgical treatment, the criteria of medical and social examination and rehabilitation, clinical and labor prognosis, indications to establishment of disability after operations concerning of Dupuytren’s contracture. In our clinic was performed three methods of operation: aponeurotomia “open hand”, partial aponeuroectomia, total aponeuroectomia. Errors in the treatment of palmar fibromatosis we shared on: preoperated, intraoperated and associated with violations of the mode of rehabilitation. The next clinical observation of 68 patients (up to 3 years after surgery with Dupuytren’s contracture of hand showed the recurrence rate amounted to 31,7%, and physical inability level is 5,9% of cases. In our opinion the most optimal operative methodic is total aponeuroectomia with rational surgical approaches. Clinical and labour prognosis depends on the manifestations of disease which can develop regardless of the stage, methods of treatment and patient's age. Disadvantageous

Foot deformities in Renaissance paintings. A mystery of symbolism, artistic licence, illusion and true representation in five renowned Renaissance painters.

Science.gov (United States)

Lazzeri, D; Castello, M F; Grassetti, L; Dashti, T; Zhang, Y X; Persichetti, P

2015-01-01

Although Renaissance artists were skilled in representing normal anatomy, a close look at some paintings reveals anatomical variations in the depiction of the feet of human figures. A systematic review has identified 25 paintings by five artists in which the presumptive medico-artistic diagnosis of congenital or acquired foot deformity seems to be varyingly present. The connection between these five painters and what factors have influenced artists' style in the depiction of such deformities is discussed. The possible iconography and medical-historical meaning of such variations, as well as the possibility of artistic licence and real representation that drove the painters to depict these deformities, is explored and debated.

Geological ductile deformation mapping at the Olkiluoto site, Eurajoki, Finland

Energy Technology Data Exchange (ETDEWEB)

Engstroem, J. [Geological Survey of Finland, Espoo (Finland)

2013-12-15

, which examined in detail also indicates dextral sense of shearing and commonly SE side up -movement. Subsequently, all earlier structural elements were again re-deformed in fourth deformation phase (D{sub 4}), which caused local small-scale shear bands together with symmetric tight folding and occasionally also large-scale open folds. This latest deformation phase also shows a distinct metasomatic or migmatitic type of rock with pronounced feldspar or quartz porphyroblasts in a fine-grained matrix. These shear bands and the S{sub 4} foliation acquired from OC 3 - OC 7, confirms the overprinting nature of the D{sub 4} deformation phase having a NNE-SSW orientation with steep dip (∼ 60 deg C) towards ESE. The thin section studies indicate that the youngest ductile deformation (D{sub 4}) seem to have a retrograde deformation of cordierite to muscovite, whereas D{sub 2} and D{sub 3} contain cordierite which is less altered. The three latest deformation phases have a significant impact on the ductile deformational history in Olkiluoto. The different phases occasionally show similar structural signatures, but it is possible to find distinguishing elements for each individual deformation phase and different parts of the Island show considerable diversity in the nature of the ductile deformation. (orig.)

Strengthening and stretching for rheumatoid arthritis of the hand (SARAH: design of a randomised controlled trial of a hand and upper limb exercise intervention - ISRCTN89936343

Directory of Open Access Journals (Sweden)

Adams Jo

2012-11-01

Full Text Available Abstract Background Rheumatoid Arthritis (RA commonly affects the hands and wrists with inflammation, deformity, pain, weakness and restricted mobility leading to reduced function. The effectiveness of exercise for RA hands is uncertain, although evidence from small scale studies is promising. The Strengthening And Stretching for Rheumatoid Arthritis of the Hand (SARAH trial is a pragmatic, multi-centre randomised controlled trial evaluating the clinical and cost effectiveness of adding an optimised exercise programme for hands and upper limbs to best practice usual care for patients with RA. Methods/design 480 participants with problematic RA hands will be recruited through 17 NHS trusts. Treatments will be provided by physiotherapists and occupational therapists. Participants will be individually randomised to receive either best practice usual care (joint protection advice, general exercise advice, functional splinting and assistive devices or best practice usual care supplemented with an individualised exercise programme of strengthening and stretching exercises. The study assessors will be blinded to treatment allocation and will follow participants up at four and 12 months. The primary outcome measure is the Hand function subscale of the Michigan Hand Outcome Questionnaire, and secondary outcomes include hand and wrist impairment measures, quality of life, and resource use. Economic and qualitative studies will also be carried out in parallel. Discussion This paper describes the design and development of a trial protocol of a complex intervention study based in therapy out-patient departments. The findings will provide evidence to support or refute the use of an optimised exercise programme for RA of the hand in addition to best practice usual care. Trial registration Current Controlled Trials ISRCTN89936343

A mechatronics platform to study prosthetic hand control using EMG signals.

Science.gov (United States)

Geethanjali, P

2016-09-01

In this paper, a low-cost mechatronics platform for the design and development of robotic hands as well as a surface electromyogram (EMG) pattern recognition system is proposed. This paper also explores various EMG classification techniques using a low-cost electronics system in prosthetic hand applications. The proposed platform involves the development of a four channel EMG signal acquisition system; pattern recognition of acquired EMG signals; and development of a digital controller for a robotic hand. Four-channel surface EMG signals, acquired from ten healthy subjects for six different movements of the hand, were used to analyse pattern recognition in prosthetic hand control. Various time domain features were extracted and grouped into five ensembles to compare the influence of features in feature-selective classifiers (SLR) with widely considered non-feature-selective classifiers, such as neural networks (NN), linear discriminant analysis (LDA) and support vector machines (SVM) applied with different kernels. The results divulged that the average classification accuracy of the SVM, with a linear kernel function, outperforms other classifiers with feature ensembles, Hudgin's feature set and auto regression (AR) coefficients. However, the slight improvement in classification accuracy of SVM incurs more processing time and memory space in the low-level controller. The Kruskal-Wallis (KW) test also shows that there is no significant difference in the classification performance of SLR with Hudgin's feature set to that of SVM with Hudgin's features along with AR coefficients. In addition, the KW test shows that SLR was found to be better in respect to computation time and memory space, which is vital in a low-level controller. Similar to SVM, with a linear kernel function, other non-feature selective LDA and NN classifiers also show a slight improvement in performance using twice the features but with the drawback of increased memory space requirement and time

Deformation-specific and deformation-invariant visual object recognition: pose vs identity recognition of people and deforming objects

Directory of Open Access Journals (Sweden)

Tristan J Webb

2014-04-01

Full Text Available When we see a human sitting down, standing up, or walking, we can recognise one of these poses independently of the individual, or we can recognise the individual person, independently of the pose. The same issues arise for deforming objects. For example, if we see a flag deformed by the wind, either blowing out or hanging languidly, we can usually recognise the flag, independently of its deformation; or we can recognise the deformation independently of the identity of the flag. We hypothesize that these types of recognition can be implemented by the primate visual system using temporo-spatial continuity as objects transform as a learning principle. In particular, we hypothesize that pose or deformation can be learned under conditions in which large numbers of different people are successively seen in the same pose, or objects in the same deformation. We also hypothesize that person-specific representations that are independent of pose, and object-specific representations that are independent of deformation and view, could be built, when individual people or objects are observed successively transforming from one pose or deformation and view to another. These hypotheses were tested in a simulation of the ventral visual system, VisNet, that uses temporal continuity, implemented in a synaptic learning rule with a short-term memory trace of previous neuronal activity, to learn invariant representations. It was found that depending on the statistics of the visual input, either pose-specific or deformation-specific representations could be built that were invariant with respect to individual and view; or that identity-specific representations could be built that were invariant with respect to pose or deformation and view. We propose that this is how pose-specific and pose-invariant, and deformation-specific and deformation-invariant, perceptual representations are built in the brain.

MetaSensing's FastGBSAR: ground based radar for deformation monitoring

Science.gov (United States)

Rödelsperger, Sabine; Meta, Adriano

2014-10-01

The continuous monitoring of ground deformation and structural movement has become an important task in engineering. MetaSensing introduces a novel sensor system, the Fast Ground Based Synthetic Aperture Radar (FastGBSAR), based on innovative technologies that have already been successfully applied to airborne SAR applications. The FastGBSAR allows the remote sensing of deformations of a slope or infrastructure from up to a distance of 4 km. The FastGBSAR can be setup in two different configurations: in Real Aperture Radar (RAR) mode it is capable of accurately measuring displacements along a linear range profile, ideal for monitoring vibrations of structures like bridges and towers (displacement accuracy up to 0.01 mm). Modal parameters can be determined within half an hour. Alternatively, in Synthetic Aperture Radar (SAR) configuration it produces two-dimensional displacement images with an acquisition time of less than 5 seconds, ideal for monitoring areal structures like dams, landslides and open pit mines (displacement accuracy up to 0.1 mm). The MetaSensing FastGBSAR is the first ground based SAR instrument on the market able to produce two-dimensional deformation maps with this high acquisition rate. By that, deformation time series with a high temporal and spatial resolution can be generated, giving detailed information useful to determine the deformation mechanisms involved and eventually to predict an incoming failure. The system is fully portable and can be quickly installed on bedrock or a basement. The data acquisition and processing can be fully automated leading to a low effort in instrument operation and maintenance. Due to the short acquisition time of FastGBSAR, the coherence between two acquisitions is very high and the phase unwrapping is simplified enormously. This yields a high density of resolution cells with good quality and high reliability of the acquired deformations. The deformation maps can directly be used as input into an Early

Stringy correlations on deformed AdS{sub 3}×S{sup 3}

Energy Technology Data Exchange (ETDEWEB)

Roychowdhury, Dibakar [Department of Physics, Ben-Gurion University of The Negev,P.O. Box 653, Beer-Sheva 84105 (Israel)

2017-03-08

In this paper, following the basic prescriptions of Gauge/String duality, we perform a strong coupling computation on classical two point correlation between local (single trace) operators in a gauge theory dual to κ-deformed AdS{sub 3}×S{sup 3} background. Our construction is based on the prescription that relates every local operator in a gauge theory to that with the (semi)classical string states propagating within the physical region surrounded by the holographic screen in deformed AdS{sub 3}. In our analysis, we treat strings as being that of a point like object located near the physical boundary of the κ-deformed Euclidean Poincare AdS{sub 3} and as an extended object with non trivial dynamics associated to S{sup 3}. It turns out that in the presence of small background deformations, the usual power law behavior associated with two point functions is suppressed exponentially by a non trivial factor which indicates a faster decay of two point correlations with larger separations. On the other hand, in the limit of large background deformations (κ≫1), the corresponding two point function reaches a point of saturation. In our analysis, we also compute finite size corrections associated with these two point functions at strong coupling. As a consistency check of our analysis, we find perfect agreement between our results to that with the earlier observations made in the context of vanishing deformation.

Optical Force Sensor for the DEXMART Hand Twisted String Actuation System

Directory of Open Access Journals (Sweden)

Gianluca PALLI

2013-01-01

Full Text Available In this paper, the force sensor developed for the twisted string actuation system of the DEXMART Hand is described. The proposed solution makes use of optoelectronic components for measuring the deformation of the properly designed motor module structure caused by the force applied to the tendon transmission system. The paper reports the working principle, the calibration and the characterization of the sensor in terms of sensitivity, repeatability, full-scale and Signal-to-Noise ratio.

Study of elastoplastic deformations self-fretting of flat cylinders by mandrelling

International Nuclear Information System (INIS)

Caron, Roger

1974-04-01

An application of the theory of thick tubes to the special case of flat cylinders which have been self-fretted by mandrelling, is presented. The following materials were used: 1 - a soft steel, XC 18 F, considered to be perfectly elastoplastic; 2 - an alloyed steel, 35 NCD 16, designated consolidable. In the first case, the slip trajectories observed on the polished cylinder surface enabled the plastic deformation region to be defined. It was found, in particular, that the average value of the mean boundary radius at the maximum pressure differs very little from that determined using basic formulas. In the second case, the plastic deformations uniformly affect the internal layers, and privileged trajectories do not exist in this region. On the other hand, the ε θ and ε r expansion curves (from deformation measurements), are continuous from the inner radius to the outer radius; the boundary radius was thus localized from considerations of its correspondence with the ε θ -ε r (shearing deformation) at the elastic limit of the material. This characteristic was determined from measurements made using a test piece provided for this purpose. The radii obtained with this method agree with the theoretical radii over only 4/5 of the total deformation, the uncertainty region being taken into consideration. The maximum value of this parameter was determined in such a way as to obtain a return to a completely elastic rest position. (author) [fr

Structural control of elastic moduli in ferrogels and the importance of non-affine deformations

Science.gov (United States)

Pessot, Giorgio; Cremer, Peet; Borin, Dmitry Y.; Odenbach, Stefan; Löwen, Hartmut; Menzel, Andreas M.

2014-09-01

One of the central appealing properties of magnetic gels and elastomers is that their elastic moduli can reversibly be adjusted from outside by applying magnetic fields. The impact of the internal magnetic particle distribution on this effect has been outlined and analyzed theoretically. In most cases, however, affine sample deformations are studied and often regular particle arrangements are considered. Here we challenge these two major simplifications by a systematic approach using a minimal dipole-spring model. Starting from different regular lattices, we take into account increasingly randomized structures, until we finally investigate an irregular texture taken from a real experimental sample. On the one hand, we find that the elastic tunability qualitatively depends on the structural properties, here in two spatial dimensions. On the other hand, we demonstrate that the assumption of affine deformations leads to increasingly erroneous results the more realistic the particle distribution becomes. Understanding the consequences of the assumptions made in the modeling process is important on our way to support an improved design of these fascinating materials.

An On-Chip RBC Deformability Checker Significantly Improves Velocity-Deformation Correlation

Directory of Open Access Journals (Sweden)

Chia-Hung Dylan Tsai

2016-10-01

Full Text Available An on-chip deformability checker is proposed to improve the velocity–deformation correlation for red blood cell (RBC evaluation. RBC deformability has been found related to human diseases, and can be evaluated based on RBC velocity through a microfluidic constriction as in conventional approaches. The correlation between transit velocity and amount of deformation provides statistical information of RBC deformability. However, such correlations are usually only moderate, or even weak, in practical evaluations due to limited range of RBC deformation. To solve this issue, we implemented three constrictions of different width in the proposed checker, so that three different deformation regions can be applied to RBCs. By considering cell responses from the three regions as a whole, we practically extend the range of cell deformation in the evaluation, and could resolve the issue about the limited range of RBC deformation. RBCs from five volunteer subjects were tested using the proposed checker. The results show that the correlation between cell deformation and transit velocity is significantly improved by the proposed deformability checker. The absolute values of the correlation coefficients are increased from an average of 0.54 to 0.92. The effects of cell size, shape and orientation to the evaluation are discussed according to the experimental results. The proposed checker is expected to be useful for RBC evaluation in medical practices.

Influence of fragment deformation and orientation on compact configuration of odd-Z superheavy nuclei

International Nuclear Information System (INIS)

Gurjit Kaur; Sandhu, Kirandeep; Sharma, Manoj K.

2016-01-01

The synthesis of heavy and superheavy nuclei is generally carried out by using hot and cold fusion reaction mechanisms. It has been noticed that, the cold fusion reactions occur at relatively low excitation energies (E*_C_N ∼ 10-20 MeV) whereas, the hot fusion reactions occur at excitation energies of E*_C_N ∼ 30- 50 MeV. The fusion mechanism is quite different in both the processes. In the cold fusion process, the interaction of spherical targets (Pb and Bi) with deformed light mass projectiles occurs. On the other hand, the fusion of deformed actinide targets with spherical "4"8Ca projectile characterize the hot interaction processes. Hence the deformations and orientations of targets and projectiles play extremely important role in the superheavy fusion process. The present analysis is carried out to aggrandize the work of which illustrate the role of deformations and orientations on even superheavy nuclei. Here, we extend this analysis for odd superheavy nuclei. It is relevant to note that the temperature and angular momentum effects are not included in the present analysis

Deformation Partitioning: The Missing Link Between Outcrop-Scale Observations And Orogen-Scale Processes

Science.gov (United States)

Attia, S.; Paterson, S. R.; Jiang, D.; Miller, R. B.

2017-12-01

Structural studies of orogenic deformation fields are mostly based on small-scale structures ubiquitous in field exposures, hand samples, and under microscopes. Relating deformation histories derived from such structures to changing lithospheric-scale deformation and boundary conditions is not trivial due to vast scale separation (10-6 107 m) between characteristic lengths of small-scale structures and lithospheric plates. Rheological heterogeneity over the range of orogenic scales will lead to deformation partitioning throughout intervening scales of structural development. Spectacular examples of structures documenting deformation partitioning are widespread within hot (i.e., magma-rich) orogens such as the well-studied central Sierra Nevada and Cascades core of western North America: (1) deformation partitioned into localized, narrow, triclinic shear zones separated by broad domains of distributed pure shear at micro- to 10 km scales; (2) deformation partitioned between plutons and surrounding metamorphic host rocks as shown by pluton-wide magmatic fabrics consistently oriented differently than coeval host rock fabrics; (3) partitioning recorded by different fabric intensities, styles, and orientations established from meter-scale grid mapping to 100 km scale domainal analyses; and (4) variations in the causes of strain and kinematics within fold-dominated domains. These complex, partitioned histories require synthesized mapping, geochronology, and structural data at all scales to evaluate partitioning and in the absence of correct scaling can lead to incorrect interpretations of histories. Forward modeling capable of addressing deformation partitioning in materials containing multiple scales of rheologically heterogeneous elements of varying characteristic lengths provides the ability to upscale the large synthesized datasets described above to plate-scale tectonic processes and boundary conditions. By comparing modeling predictions from the recently developed

A novel surgical correction and innovative splint for swan neck deformity in hypermobility syndrome

Directory of Open Access Journals (Sweden)

Karthik Vishwanathan

2018-01-01

Full Text Available Splinting is a great domain of occupational therapy profession. Making a splint for the patient would depend on the need or requirement of the problems and deformities. Swan neck deformity is an uncommon condition, and it can be seen in rheumatoid arthritis, cerebral palsy, and after trauma. Conservative treatment of the swan neck deformity is available by different static splints only. There are very few reports of surgical correction of swan-neck deformity in benign hypermobility syndrome. This case report describes the result of novel surgical intervention and an innovative hand splint in a 20-year-old female with a history of cardiovascular stroke with no residual neurological deficit. She presented with correctable swan neck deformity and failed to improve with static ring splints to correct the deformity. She underwent volar plate plication of the proximal interphalangeal joint of the left ring finger along with hemitenodesis of ulnar slip of flexor digitorum superficialis (FDS tendon whereby, the ulnar slip of FDS was passed through a small surgically created rent in A2 pulley and sutured back to itself. Postoperatively, the patient was referred to occupational therapy for splinting with the instruction that the splint would work sometimes for as static and some time as dynamic for positional and correction of the finger. After occupational therapy intervention and splinting, the patient had a full correction of the swan-neck deformity with near full flexion of the operated finger and can work independently.

Study of deformability in salt deposits near underground cavities

International Nuclear Information System (INIS)

Ouvry, J.F.; Massal, P.; Laviguerie, R.; Matifat, J.M.

1992-01-01

The present report relates the in-situ tests carried out in the Varangeville mine (France). This work is part of a larger research programme, on the mechanical behaviour of a salt massif, carried out by BRGM and Ecoles des Mines de Paris. The aim of the in-situ tests was to collect data for the validation of the behaviour law, based on the laboratory tests. Those tests consisted of, on the one hand the short term mechanical characteristics measurement, and on the other hand the long term creep measurement of borehole walls. The deformability tests at short term show a large dispersion of the modulus values, which range from 3000 to 6100 MPa; these are smaller than those obtained in laboratory, that range from 6200 to 7500 MPa. The second part has first required the construction of a prototype designed to measure the creep of borehole walls while applying a constant internal pressure set to a chosen value. The tests were carried out in a pilar of the mine. The first step, with an internal pressure of 2.5 MPa, shows after 300 days a borehole walls divergence ranged from 0.2 per cent in the vertical direction, up to 0.7 per cent in the horizontal direction. The second step, with a pressure of 1.2 MPa, shows a stabilization of the diametral deformation after 200 days except for the horizontal direction. 12 figs., 1 tab., 2 appendices

Real-Time Control of an Exoskeleton Hand Robot with Myoelectric Pattern Recognition.

Science.gov (United States)

Lu, Zhiyuan; Chen, Xiang; Zhang, Xu; Tong, Kay-Yu; Zhou, Ping

2017-08-01

Robot-assisted training provides an effective approach to neurological injury rehabilitation. To meet the challenge of hand rehabilitation after neurological injuries, this study presents an advanced myoelectric pattern recognition scheme for real-time intention-driven control of a hand exoskeleton. The developed scheme detects and recognizes user's intention of six different hand motions using four channels of surface electromyography (EMG) signals acquired from the forearm and hand muscles, and then drives the exoskeleton to assist the user accomplish the intended motion. The system was tested with eight neurologically intact subjects and two individuals with spinal cord injury (SCI). The overall control accuracy was [Formula: see text] for the neurologically intact subjects and [Formula: see text] for the SCI subjects. The total lag of the system was approximately 250[Formula: see text]ms including data acquisition, transmission and processing. One SCI subject also participated in training sessions in his second and third visits. Both the control accuracy and efficiency tended to improve. These results show great potential for applying the advanced myoelectric pattern recognition control of the wearable robotic hand system toward improving hand function after neurological injuries.

Left handedness and spine deformities in early adolescence

International Nuclear Information System (INIS)

Milenkovic, Sanja; Kocijancic, Radojka; Belojevic, Goran

2004-01-01

The aim of this study was to investigate the relation between laterality and spine deformities in early adolescence, with special reference to sex differences. Interviews, anthropometric measurements and clinical examinations of body posture were carried out on a sample of 2546 schoolchildren, aged from 11 to 14 years, in seven elementary schools in the centre of Belgrade. Possible confounding factors (age, sex, body weight and body height) were controlled for. The overall prevalence of spine deformities (scoliosis and/or thoracic hyperkyphosis) in the investigated population was 11.8%, out of which there were 7.8% adolescents with scoliosis, 4.0% with thoracic hyperkyphosis, and 0.3% with both spine deformities. The prevalence of scoliosis was 2.7 times higher in girls compared to boys (11.7% vs. 4.3%) while the prevalence of thoracic hyperkyphosis was 1,6 higher among boys (5.0% vs. 3.2%). We found 7.6% of the schoolchildren examined to be left-handed. Left handedness was significantly related to scoliosis in girls (crude OR=1.60 and 95% confidence interval=1.01-2.54). Multivariate analysis showed that significant independent factors for scoliosis were female sex (p < 0.001), age (p=0.01) and left handedness (p=0.02). We did not find any appreciable relation between left handedness and thoracic hyperkyphosis in both sexes

Assessment of fatigue crack length via plastic deformation in compact tension specimens using magnetic Barkhausen noise

International Nuclear Information System (INIS)

Reyes-Rodriguez, F. de los; Diego-Velasco, G. de; Capo-Sanchez, J.; Franco-Fidalgo, E.

2013-01-01

In this paper the influence of different parameters on crack length is determined via plastic deformation using magnetic Barkhausen noise; the compact specimens steel used in this study were 12Cr1MoV and 11Cr1Mo, which are used for steam transportation on power plants. The main objective of this paper is to determine the crack length and its incubation time using magnetic Barkhausen noise, which lets to improve the pre-cracking process prior creep crack growth rate test simulating the real conditions of high pressure and temperature of main steam lines. Results showed that mean root square and maximum pick of voltage decrease with plastic deformation for each steel analyzed in this work, on the other hand, with the increasing of plastic deformation, a logic relationship between plastic deformation and spectrum density is observed for mid frequencies values, as well as, a variation of the amplitude, width and shape of the Barkhausen signal envelope. (Author)

Helping hands: A cluster randomised trial to evaluate the effectiveness of two different strategies for promoting hand hygiene in hospital nurses

Directory of Open Access Journals (Sweden)

Hulscher Marlies

2011-09-01

Full Text Available Abstract Background Hand hygiene prescriptions are the most important measure in the prevention of hospital-acquired infections. Yet, compliance rates are generally below 50% of all opportunities for hand hygiene. This study aims at evaluating the short- and long-term effects of two different strategies for promoting hand hygiene in hospital nurses. Methods/design This study is a cluster randomised controlled trial with inpatient wards as the unit of randomisation. Guidelines for hand hygiene will be implemented in this study. Two strategies will be used to improve the adherence to guidelines for hand hygiene. The state-of-the-art strategy is derived from the literature and includes education, reminders, feedback, and targeting adequate products and facilities. The extended strategy also contains activities aimed at influencing social influence in groups and enhancing leadership. The unique contribution of the extended strategy is built upon relevant behavioural science theories. The extended strategy includes all elements of the state-of-the-art strategy supplemented with gaining active commitment and initiative of ward management, modelling by informal leaders at the ward, and setting norms and targets within the team. Data will be collected at four points in time, with six-month intervals. An average of 3,000 opportunities for hand hygiene in approximately 900 nurses will be observed at each time point. Discussion Performing and evaluating an implementation strategy that also targets the social context of teams may considerably add to the general body of knowledge in this field. Results from our study will allow us to draw conclusions on the effects of different strategies for the implementation of hand hygiene guidelines, and based on these results we will be able to define a preferred implementation strategy for hospital based nursing. Trial registration The study is registered as a Clinical Trial in ClinicalTrials.gov, dossier number: NCT

Analysis of Information Remaining on Hand Held Devices Offered for Sale on the Second Hand Market

Directory of Open Access Journals (Sweden)

Andy Jones

2008-06-01

resellers.The study was carried out by the security research team at the BT IT Futures Centre in conjunction with Edith Cowan University in Australia and the University of Glamorgan in the UK. The basis of the research was to acquire a number of second hand held devices from a diverse range of sources and then determine whether they still contained information relating to a previous owner or whether the information had been effectively removed. The devices that were obtained for the research were supplied blind to the researchers through a third party. The ‘blind’ supply of the devices meant that the people undertaking the research were provided with no information about the device and that the source of the devices and any external markings were hidden from them. This process was put in place to ensure that any findings of the research were based solely on the information that could be recovered from the digital storage media that was contained within the device.The underlying methodology that was used in the research was based on the forensic imaging of the devices. A forensic image of a device is a copy of the digital media that has been created in a scientifically sound manner to a standard that is acceptable to the courts. This procedure was implemented to ensure that the evidential integrity of the devices was maintained, with the devices also then being stored in a secure manner.  All subsequent research was then conducted on the image of the device. This was considered to be a sensible precaution against the possibility that information discovered on a device might indicate criminal activity and require the involvement of law enforcement.  Following the forensic imaging of the devices, the images that were created were then analyzed to determine whether any information remained and whether it could be easily recovered using commonly available tools and techniques that anyone who had purchased the device could acquire.

q-deformed Weinberg-Salam model and q-deformed Maxwell equations

International Nuclear Information System (INIS)

Alavi, S.A.; Sarbishaei, M.; Mokhtari, A.

2000-01-01

We study the q-deformation of the gauge part of the Weinberg-Salam model and show that the q-deformed theory involves new interactions. We then obtain q-deformed Maxwell equations from which magnetic monopoles appear naturally. (author)

Automated monitoring: a potential solution for achieving sustainable improvement in hand hygiene practices.

Science.gov (United States)

Levchenko, Alexander I; Boscart, Veronique M; Fernie, Geoff R

2014-08-01

Adequate hand hygiene is often considered as the most effective method of reducing the rates of hospital-acquired infections, which are one of the major causes of increased cost, morbidity, and mortality in healthcare. Electronic monitoring technologies provide a promising direction for achieving sustainable hand hygiene improvement by introducing the elements of automated feedback and creating the possibility to automatically collect individual hand hygiene performance data. The results of the multiphase testing of an automated hand hygiene reminding and monitoring system installed in a complex continuing care setting are presented. The study included a baseline Phase 1, with the system performing automated data collection only, a preintervention Phase 2 with hand hygiene status indicator enabled, two intervention Phases 3 and 4 with the system generating hand hygiene reminding signals and periodic performance feedback sessions provided, and a postintervention Phase 5 with only hand hygiene status indicator enabled and no feedback sessions provided. A significant increase in hand hygiene performance observed during the first intervention Phase 3 was sustained over the second intervention Phase 4, with the postintervention phase also indicating higher hand hygiene activity rates compared with the preintervention and baseline phases. The overall trends observed during the multiphase testing, the factors affecting acceptability of the automated hand hygiene monitoring system, and various strategies of technology deployment are discussed.

Functionality predictors in acquired brain damage.

Science.gov (United States)

Huertas Hoyas, E; Pedrero Pérez, E J; Águila Maturana, A M; García López-Alberca, S; González Alted, C

2015-01-01

Most individuals who have survived an acquired brain injury present consequences affecting the sensorimotor, cognitive, affective or behavioural components. These deficits affect the proper performance of daily living activities. The aim of this study is to identify functional differences between individuals with unilateral acquired brain injury using functional independence, capacity, and performance of daily activities. Descriptive cross-sectional design with a sample of 58 people, with right-sided injury (n=14 TBI; n=15 stroke) or left-sided injury (n = 14 TBI, n = 15 stroke), right handed, and with a mean age of 47 years and time since onset of 4 ± 3.65 years. The functional assessment/functional independence measure (FIM/FAM) and the International Classification of Functioning (ICF) were used for the study. The data showed significant differences (P<.000), and a large size effect (dr=0.78) in the cross-sectional estimates, and point to fewer restrictions for patients with a lesion on their right side. The major differences were in the variables 'speaking' and 'receiving spoken messages' (ICF variables), and 'Expression', 'Writing' and 'intelligible speech' (FIM/FAM variables). In the linear regression analysis, the results showed that only 4 FIM/FAM variables, taken together, predict 44% of the ICF variance, which measures the ability of the individual, and up to 52% of the ICF, which measures the individual's performance. Gait alone predicts a 28% of the variance. It seems that individuals with acquired brain injury in the left hemisphere display important differences regarding functional and communication variables. The motor aspects are an important prognostic factor in functional rehabilitation. Copyright © 2013 Sociedad Española de Neurología. Published by Elsevier España, S.L.U. All rights reserved.

WE-G-BRF-01: Adaptation to Intrafraction Tumor Deformation During Intensity-Modulated Radiotherapy: First Proof-Of-Principle Demonstration

International Nuclear Information System (INIS)

Ge, Y; OBrien, R; Shieh, C; Booth, J; Keall, P

2014-01-01

Purpose: Intrafraction tumor deformation limits targeting accuracy in radiotherapy and cannot be adapted to by current motion management techniques. This study simulated intrafractional treatment adaptation to tumor deformations using a dynamic Multi-Leaf Collimator (DMLC) tracking system during Intensity-modulated radiation therapy (IMRT) treatment for the first time. Methods: The DMLC tracking system was developed to adapt to the intrafraction tumor deformation by warping the planned beam aperture guided by the calculated deformation vector field (DVF) obtained from deformable image registration (DIR) at the time of treatment delivery. Seven single phantom deformation images up to 10.4 mm deformation and eight tumor system phantom deformation images up to 21.5 mm deformation were acquired and used in tracking simulation. The intrafraction adaptation was simulated at the DMLC tracking software platform, which was able to communicate with the image registration software, reshape the instantaneous IMRT field aperture and log the delivered MLC fields.The deformation adaptation accuracy was evaluated by a geometric target coverage metric defined as the sum of the area incorrectly outside and inside the reference aperture. The incremental deformations were arbitrarily determined to take place equally over the delivery interval. The geometric target coverage of delivery with deformation adaptation was compared against the delivery without adaptation. Results: Intrafraction deformation adaptation during dynamic IMRT plan delivery was simulated for single and system deformable phantoms. For the two particular delivery situations, over the treatment course, deformation adaptation improved the target coverage by 89% for single target deformation and 79% for tumor system deformation compared with no-tracking delivery. Conclusion: This work demonstrated the principle of real-time tumor deformation tracking using a DMLC. This is the first step towards the development of an

Commutative deformations of general relativity: nonlocality, causality, and dark matter

Energy Technology Data Exchange (ETDEWEB)

De Vegvar, P.G.N. [SWK Research, Bellingham, WA (United States)

2017-01-15

Hopf algebra methods are applied to study Drinfeld twists of (3+1)-diffeomorphisms and deformed general relativity on commutative manifolds. A classical nonlocality length scale is produced above which microcausality emerges. Matter fields are utilized to generate self-consistent Abelian Drinfeld twists in a background independent manner and their continuous and discrete symmetries are examined. There is negligible experimental effect on the standard model of particles. While baryonic twist producing matter would begin to behave acausally for rest masses above ∝1-10 TeV, other possibilities are viable dark matter candidates or a right-handed neutrino. First order deformed Maxwell equations are derived and yield immeasurably small cosmological dispersion and produce a propagation horizon only for photons at or above Planck energies. This model incorporates dark matter without any appeal to extra dimensions, supersymmetry, strings, grand unified theories, mirror worlds, or modifications of Newtonian dynamics. (orig.)

Assessment of 3D hydrologic deformation using GRACE and GPS

Science.gov (United States)

Watson, C. S.; Tregoning, P.; Fleming, K.; Burgette, R. J.; Featherstone, W. E.; Awange, J.; Kuhn, M.; Ramillien, G.

2009-12-01

Hydrological processes cause variations in gravitational potential and surface deformations, both of which are detectable with ever increasing precision using space geodetic techniques. By comparing the elastic deformation computed from continental water load estimates derived from the Gravity Recovery and Climate Experiment (GRACE), with three-dimensional surface deformation derived from GPS observations, there is clear potential to better understand global to regional hydrological processes, in addition to acquiring further insight into the systematic error contributions affecting each space geodetic technique. In this study, we compare elastic deformation derived from water load estimates taken from the CNES, CSR, GFZ and JPL time variable GRACE fields. We compare these surface displacements with those derived at a global network of GPS sites that have been homogeneously reprocessed in the GAMIT/GLOBK suite. We extend our comparison to include a series of different GPS solutions, with each solution only subtly different based on the methodology used to down weight the height component in realizing site coordinates on the terrestrial reference frame. Each of the GPS solutions incorporate modeling of atmospheric loading and utilization of the VMF1 and a priori zenith hydrostatic delays derived via ray tracing through ECMWF meteorological fields. The agreement between GRACE and GPS derived deformations is not limited to the vertical component, with excellent agreement in the horizontal component across areas where large hydrologic signals occur over broad spatial scales (with correlation in horizontal components as high as 0.9). Agreement is also observed at smaller scales, including across Europe. These comparisons assist in understanding the magnitude of current error contributions within both space geodetic techniques. With the emergence of homogeneously reprocessed GPS time series spanning the GRACE mission, this technique offers one possible means of

New Methods for Imaging Evaluation of Chest Wall Deformities

Directory of Open Access Journals (Sweden)

Ana Lain

2017-12-01

Full Text Available AimThe purpose of this study is to describe the development of an external 3-dimensional (3D scanner as a noninvasive method for imaging chest wall deformities. It allows objective assessment, reconstruction of the area of interest, and evaluation of the severity of the deformity by using external indexes.External 3D scanning systemThe OrtenBodyOne scanner (Orten, Lyon, France uses depth sensors to scan the entire 3D external body surface of a patient. The depth sensors combine structured light with two classic computer vision techniques: depth from focus and depth from stereo. The data acquired are processed and analyzed using the Orten-Clinic software.Materials and methodsTo investigate the performance of the device, a preliminary prospective study (January 2015–March 2016 was carried out in patients attending our hospital chest wall deformities unit. In total, 100 patients (children and young adults with pectus excavatum or pectus carinatum, treated by surgery or non-operative methods were included. In patients undergoing non-operative treatment, external 3D scanning was performed monthly until complete correction was achieved. In surgically treated patients, scanning was done before and after surgical correction. In 42 patients, computed tomography (CT was additionally performed and correlations between the Haller index calculated by CT and the external Haller index using external scanning were investigated using a Student’s test (r = 0.83.ConclusionExternal scanning is an effective, objective, radiation-free means to diagnose and follow-up patients with chest wall deformities. Externally measured indexes can be used to evaluate the severity of these conditions and the treatment outcomes.

Algorithm for Primary Full-thickness Skin Grafting in Pediatric Hand Burns

Directory of Open Access Journals (Sweden)

Yang Seo Park

2012-09-01

Full Text Available BackgroundPediatric hand burns are a difficult problem because they lead to serious hand deformities with functional impairment due to rapid growth during childhood. Therefore, adequate management is required beginning in the acute stage. Our study aims to establish surgical guidelines for a primary full-thickness skin graft (FTSG in pediatric hand burns, based on long-term observation periods and existing studies.MethodsFrom January 2000 to May 2011, 210 patients underwent primary FTSG. We retrospectively studied the clinical course and treatment outcomes based on the patients' medical records. The patients' demographics, age, sex, injury site of the fingers, presence of web space involvement, the incidence of postoperative late deformities, and the duration of revision were critically analyzed.ResultsThe mean age of the patients was 24.4 months (range, 8 to 94 months, consisting of 141 males and 69 females. The overall observation period was 6.9 years (range, 1 to 11 years on average. At the time of the burn, 56 cases were to a single finger, 73 to two fingers, 45 to three fingers, and 22 to more than three. Among these cases, 70 were burns that included a web space (33.3%. During the observation, 25 cases underwent corrective operations with an average period of 40.6 months.ConclusionsIn the volar area, primary full-thickness skin grafting can be a good indication for an isolated injured finger, excluding the web spaces, and injuries of less than three fingers including the web spaces. Also, in the dorsal area, full-thickness skin grafting can be a good indication. However, if the donor site is insufficient and the wound is large, split-thickness skin grafting can be considered.

Investigating Corrosion, Wear Resistance and Friction of AA5454-O Series after its Severe Deformation by Rolling

Directory of Open Access Journals (Sweden)

Sinan SEZEK

2017-02-01

Full Text Available AA5454-O is an easily wrought, or in other words, a ductile aluminium alloy, however, its mechanical properties are inferior as compared to those of other alloys. The change taking place in corrosion resistance of AA5454-O alloy as a result of its severe plastic deformation (SPD by rolling has been investigated in this study. It has been observed that significant changes occurred in abrasion wear and corrosion resistances of AA5454-O alloy, which was severely deformed up to 80 % by rolling process. Corrosion resistance of the alloy that was severely deformed by rolling has increased. The effect of deformation rate on corrosion has been investigated by applying potentiodynamic test whereas on the other hand such change has been evidenced also through corrosion test. It has been observed that friction coefficient of severely deformed AA5454-O alloy varied by around 10 %, and that, associated with such change, its wear resistance also increased considerably. It has been determined that, as a result of severe deformation by rolling, hardness values rose in areas where the alloy was in contact with rolling surface. In this study, wear resistance of severely deformed alloy has been investigated as well. It has been observed that deformation value contributed positively to the increase in wear resistance.DOI: http://dx.doi.org/10.5755/j01.ms.23.1.14650

Predicting welding distortion in a panel structure with longitudinal stiffeners using inherent deformations obtained by inverse analysis method.

Science.gov (United States)

Liang, Wei; Murakawa, Hidekazu

2014-01-01

Welding-induced deformation not only negatively affects dimension accuracy but also degrades the performance of product. If welding deformation can be accurately predicted beforehand, the predictions will be helpful for finding effective methods to improve manufacturing accuracy. Till now, there are two kinds of finite element method (FEM) which can be used to simulate welding deformation. One is the thermal elastic plastic FEM and the other is elastic FEM based on inherent strain theory. The former only can be used to calculate welding deformation for small or medium scale welded structures due to the limitation of computing speed. On the other hand, the latter is an effective method to estimate the total welding distortion for large and complex welded structures even though it neglects the detailed welding process. When the elastic FEM is used to calculate the welding-induced deformation for a large structure, the inherent deformations in each typical joint should be obtained beforehand. In this paper, a new method based on inverse analysis was proposed to obtain the inherent deformations for weld joints. Through introducing the inherent deformations obtained by the proposed method into the elastic FEM based on inherent strain theory, we predicted the welding deformation of a panel structure with two longitudinal stiffeners. In addition, experiments were carried out to verify the simulation results.

Crustal structure and tectonic deformation of the southern Ecuadorian margin

Science.gov (United States)

Calahorrano, Alcinoe; Collot, Jean-Yves; Sage, Françoise; Ranero, César R.

2010-05-01

Multichannel seismic lines acquired during the SISTEUR cruise (2000) provide new constraints on the structure and deformation of the subduction zone at the southern Ecuadorian margin, from the deformation front to the continental shelf of the Gulf of Guayaquil. The pre-stack depth migrated images allows to characterise the main structures of the downgoing and overriding plates and to map the margin stratigraphy in order to propose a chronology of the deformation, by means of integrating commercial well data and industry seismic lines located in the gulf area. The 100-km-long seismic lines show the oceanic Nazca plate underthrusting the South American plate, as well as the subduction channel and inter-plate contact from the deformation front to about 90 km landward and ~20 km depth. Based on seismic structure we identify four upper-plate units, consisting of basement and overlaying sedimentary sequences A, B and C. The sedimentary cover varies along the margin, being few hundreds of meters thick in the lower and middle slope, and ~2-3 km thick in the upper slope. Exceptionally, a ~10-km -thick basin, here named Banco Peru basin, is located on the upper slope at the southernmost part of the gulf. This basin seems to be the first evidence of the Gulf of Guayaquil opening resulting from the NE escaping of the North Andean Block. Below the continental shelf, thick sedimentary basins of ~6 to 8 km occupy most of the gulf area. Tectonic deformation across most of the upper-plate is dominated by extensional regime, locally disturbed by diapirism. Compression evidences are restricted to the deformation front and surrounding areas. Well data calibrating the seismic profiles indicate that an important portion of the total thickness of the sedimentary coverage of the overriding plate are Miocene or older. The data indicate the extensional deformation resulting from the NE motion of the North Andean Block and the opening of the Gulf of Guayaquil, evolves progressively in age

Hand hygiene technique quality evaluation in nursing and medicine students of two academic courses

Directory of Open Access Journals (Sweden)

Manuela Škodová

2015-08-01

Full Text Available AbstractObjective: because they are health professionals, nursing and medical students' hands during internships can function as a transmission vehicle for hospital-acquired infections.Method: a descriptive study with nursing and medical degree students on the quality of the hand hygiene technique, which was assessed via a visual test using a hydroalcoholic solution marked with fluorescence and an ultraviolet lamp.Results: 546 students were assessed, 73.8% from medicine and 26.2% from nursing. The area of the hand with a proper antiseptic distribution was the palm (92.9%; areas not properly scrubbed were the thumbs (55.1%. 24.7% was very good in both hands, 29.8% was good, 25.1% was fair, and 20.3% was poor. The worst assessed were the male, nursing and first year students. There were no significant differences in the age groups.Conclusions: hand hygiene technique is not applied efficiently. Education plays a key role in setting a good practice base in hand hygiene, theoretical knowledge, and in skill development, as well as good practice reinforcement.

SU-F-J-81: Evaluation of Automated Deformable Registration Between Planning Computed Tomography (CT) and Daily Cone Beam CT Images Over the Course of Prostate Cancer Radiotherapy

Energy Technology Data Exchange (ETDEWEB)

Matney, J; Hammers, J; Kaidar-Person, O; Wang, A; Chen, R; Das, S; Marks, L; Mavroidis, P [University North Carolina, Chapel Hill, NC (United States)

2016-06-15

Purpose: To compute daily dose delivered during radiotherapy, deformable registration needs to be relatively fast, automated, and accurate. The aim of this study was to evaluate the performance of commercial deformable registration software for deforming between two modalities: planning computed tomography (pCT) images acquired for treatment planning and cone beam (CB) CT images acquired prior to each fraction of prostate cancer radiotherapy. Methods: A workflow was designed using MIM Software™ that aligned and deformed pCT into daily CBCT images in two steps: (1) rigid shifts applied after daily CBCT imaging to align patient anatomy to the pCT and (2) normalized intensity-based deformable registration to account for interfractional anatomical variations. The physician-approved CTV and organ and risk (OAR) contours were deformed from the pCT to daily CBCT over the course of treatment. The same structures were delineated on each daily CBCT by a radiation oncologist. Dice similarity coefficient (DSC) mean and standard deviations were calculated to quantify the deformable registration quality for prostate, bladder, rectum and femoral heads. Results: To date, contour comparisons have been analyzed for 31 daily fractions of 2 of 10 of the cohort. Interim analysis shows that right and left femoral head contours demonstrate the highest agreement (DSC: 0.96±0.02) with physician contours. Additionally, deformed bladder (DSC: 0.81±0.09) and prostate (DSC: 0.80±0.07) have good agreement with physician-defined daily contours. Rectum contours have the highest variations (DSC: 0.66±0.10) between the deformed and physician-defined contours on daily CBCT imaging. Conclusion: For structures with relatively high contrast boundaries on CBCT, the MIM automated deformable registration provided accurate representations of the daily contours during treatment delivery. These findings will permit subsequent investigations to automate daily dose computation from CBCT. However

Differences in microbiological profile between community-acquired, healthcare-associated and hospital-acquired infections.

Science.gov (United States)

Cardoso, Teresa; Ribeiro, Orquídea; Aragão, Irene; Costa-Pereira, Altamiro; Sarmento, António

2013-01-01

Microbiological profiles were analysed and compared for intra-abdominal, urinary, respiratory and bloodstream infections according to place of acquisition: community-acquired, with a separate analysis of healthcare-associated, and hospital-acquired. Prospective cohort study performed at a university tertiary care hospital over 1 year. Inclusion criteria were meeting the Centers for Disease Control definition of intra-abdominal, urinary, respiratory and bloodstream infections. A total of 1035 patients were included in the study. More than 25% of intra-abdominal infections were polymicrobial; multi-drug resistant gram-negatives were 38% in community-acquired, 50% in healthcare-associated and 57% in hospital-acquired. E. coli was the most prevalent among urinary infections: 69% in community-acquired, 56% in healthcare-associated and 26% in hospital-acquired; ESBL producers' pathogens were 10% in healthcare-associated and 3% in community-acquired and hospital-acquired. In respiratory infections Streptococcus pneumoniae was the most prevalent in community-acquired (54%) and MRSA in healthcare-associated (24%) and hospital-acquired (24%). A significant association was found between MRSA respiratory infection and hospitalization in the previous year (adjusted OR = 6.3), previous instrumentation (adjusted OR = 4.3) and previous antibiotic therapy (adjusted OR = 5.7); no cases were documented among patients without risk factors. Hospital mortality rate was 10% in community-acquired, 14% in healthcare-associated and 19% in hospital-acquired infection. This study shows that healthcare-associated has a different microbiologic profile than those from community or hospital acquired for the four main focus of infection. Knowledge of this fact is important because the existing guidelines for community-acquired are not entirely applicable for this group of patients.

Outcome and safety analysis of 3D printed patient specific pedicle screw jigs for complex spinal deformities: A comparative study.

Science.gov (United States)

Garg, Bhavuk; Gupta, Manish; Singh, Menaka; Kalyanasundaram, Dinesh

2018-05-03

Spinal deformities are very challenging to treat and have a great risk of neurological complications due to hardware placement during corrective surgery. Various techniques have been introduced to ensure safe and accurate placement of pedicle screws. Patient-specific screw guides with pre-drawn and pre-validated trajectory seems to be an attractive option. We have focused on developing 3D printing technique for complex spinal deformities in India. This study also aimed to compare the placement of pedicle screw with 3D printing and free hand technique. This is a retrospective comparative clinical study at an academic institutional setting. A total of 20 patients were enrolled during the study, 10 were operated with the help of 3D printing (group 1) and 10 were operated with freehand technique (group 2). Group 1 included 6 congenital, 3 adolescent idiopathic scoliosis (AIS), one post tubercular kyphosis and Group 2 included 5 congenital, 4 AIS and one post tubercular kyphosis patient. Primary outcomes were measured in terms of screw violation and secondary outcome were measured in terms of Surgical time, Blood loss, Radiation exposure (no. of shoots required) and complications. MIMICS v18.0 Software was used for 3D reconstruction from CT scan images of all the patients. 3-Matic software was used to create drill guide. 3-D printer from Stratasys Mojo ABS P 430 model material cartilage (a thermoplastic material) was used for printing of vertebrae model and jigs. Two sample test of proportion was used to compare correctly and wrongly pedicle screw placement with 3D printing and freehand technique. T-test with equal variance was used for operating surgical time and blood loss. This work was carried out by collaboration of Orthopaedics Department, All India Institute of Medical Sciences (AIIMS), New Delhi and Biomedical Engineering Department, Indian Institute of Technology (IIT) Delhi. This project received the grant of USD 60000 from Department of Biotechnology (DBT

The ANACONDA algorithm for deformable image registration in radiotherapy

International Nuclear Information System (INIS)

Weistrand, Ola; Svensson, Stina

2015-01-01

Purpose: The purpose of this work was to describe a versatile algorithm for deformable image registration with applications in radiotherapy and to validate it on thoracic 4DCT data as well as CT/cone beam CT (CBCT) data. Methods: ANAtomically CONstrained Deformation Algorithm (ANACONDA) combines image information (i.e., intensities) with anatomical information as provided by contoured image sets. The registration problem is formulated as a nonlinear optimization problem and solved with an in-house developed solver, tailored to this problem. The objective function, which is minimized during optimization, is a linear combination of four nonlinear terms: 1. image similarity term; 2. grid regularization term, which aims at keeping the deformed image grid smooth and invertible; 3. a shape based regularization term which works to keep the deformation anatomically reasonable when regions of interest are present in the reference image; and 4. a penalty term which is added to the optimization problem when controlling structures are used, aimed at deforming the selected structure in the reference image to the corresponding structure in the target image. Results: To validate ANACONDA, the authors have used 16 publically available thoracic 4DCT data sets for which target registration errors from several algorithms have been reported in the literature. On average for the 16 data sets, the target registration error is 1.17 ± 0.87 mm, Dice similarity coefficient is 0.98 for the two lungs, and image similarity, measured by the correlation coefficient, is 0.95. The authors have also validated ANACONDA using two pelvic cases and one head and neck case with planning CT and daily acquired CBCT. Each image has been contoured by a physician (radiation oncologist) or experienced radiation therapist. The results are an improvement with respect to rigid registration. However, for the head and neck case, the sample set is too small to show statistical significance. Conclusions: ANACONDA

Stability of surface plastic flow in large strain deformation of metals

Science.gov (United States)

Viswanathan, Koushik; Udapa, Anirduh; Sagapuram, Dinakar; Mann, James; Chandrasekar, Srinivasan

We examine large-strain unconstrained simple shear deformation in metals using a model two-dimensional cutting system and high-speed in situ imaging. The nature of the deformation mode is shown to be a function of the initial microstructure state of the metal and the deformation geometry. For annealed metals, which exhibit large ductility and strain hardening capacity, the commonly assumed laminar flow mode is inherently unstable. Instead, the imposed shear is accommodated by a highly rotational flow-sinuous flow-with vortex-like components and large-amplitude folding on the mesoscale. Sinuous flow is triggered by a plastic instability on the material surface ahead of the primary region of shear. On the other hand, when the material is extensively strain-hardened prior to shear, laminar flow again becomes unstable giving way to shear banding. The existence of these flow modes is established by stability analysis of laminar flow. The role of the initial microstructure state in determining the change in stability from laminar to sinuous / shear-banded flows in metals is elucidated. The implications for cutting, forming and wear processes for metals, and to surface plasticity phenomena such as mechanochemical Rehbinder effects are discussed.

Deformation and kinematics of the central Kirthar Fold Belt, Pakistan

Science.gov (United States)

Hinsch, Ralph; Hagedorn, Peter; Asmar, Chloé; Nasim, Muhammad; Aamir Rasheed, Muhammad; Kiely, James M.

2017-04-01

The Kirthar Fold Belt is part of the lateral mountain belts in Pakistan linking the Himalaya orogeny with the Makran accretionary wedge. This region is deforming very oblique/nearly parallel to the regional plate motion vector. The study area is situated between the prominent Chaman strike-slip fault in the West and the un-deformed foreland (Kirthar Foredeep/Middle Indus Basin) in the East. The Kirthar Fold Belt is subdivided into several crustal blocks/units based on structural orientation and deformation style (e.g. Kallat, Khuzdar, frontal Kirthar). This study uses newly acquired and depth-migrated 2D seismic lines, surface geology observations and Google Earth assessments to construct three balanced cross sections for the frontal part of the fold belt. Further work was done in order to insure the coherency of the built cross-sections by taking a closer look at the regional context inferred from published data, simple analogue modelling, and constructed regional sketch sections. The Khuzdar area and the frontal Kirthar Fold Belt are dominated by folding. Large thrusts with major stratigraphic repetitions are not observed. Furthermore, strike-slip faults in the Khuzdar area are scarce and not observed in the frontal Kirthar Fold Belt. The regional structural elevation rises from the foreland across the Kirthar Fold Belt towards the hinterland (Khuzdar area). These observations indicate that basement-involved deformation is present at depth. The domination of folding indicates a weak decollement below the folds (soft-linked deformation). The fold pattern in the Khuzdar area is complex, whereas the large folds of the central Kirthar Fold Belt trend SSW-NNE to N-S and are best described as large detachment folds that have been slightly uplifted by basement involved transpressive deformation underneath. Towards the foreland, the deformation is apparently more hard-linked and involves fault-propagation folding and a small triangle zone in Cretaceous sediments

Deformation twinning in a creep-deformed nanolaminate structure

International Nuclear Information System (INIS)

Hsiung, Luke L

2010-01-01

The underlying mechanism of deformation twinning occurring in a TiAl-(γ)/Ti 3 Al-(α 2 ) nanolaminate creep deformed at elevated temperatures has been studied. Since the multiplication and propagation of lattice dislocations in both γ and α 2 thin lamellae are very limited, the total flow of lattice dislocations becomes insufficient to accommodate the accumulated creep strains. Consequently, the movement of interfacial dislocations along the laminate interfaces, i.e., interface sliding, becomes an alternative deformation mode of the nanolaminate structure. Pile-ups of interfacial dislocations occur when interfacial ledges and impinged lattice dislocations act as obstacles to impede the movement of interfacial dislocations. Deformation twinning can accordingly take place to relieve a stress concentration resulting from the pile-up of interfacial dislocations. An interface-controlled twinning mechanism driven by the pile-up and dissociation of interfacial dislocations is accordingly proposed.

Deformation twinning in a creep-deformed nanolaminate structure

Science.gov (United States)

Hsiung, Luke L.

2010-10-01

The underlying mechanism of deformation twinning occurring in a TiAl-(γ)/Ti3Al-(α2) nanolaminate creep deformed at elevated temperatures has been studied. Since the multiplication and propagation of lattice dislocations in both γ and α2 thin lamellae are very limited, the total flow of lattice dislocations becomes insufficient to accommodate the accumulated creep strains. Consequently, the movement of interfacial dislocations along the laminate interfaces, i.e., interface sliding, becomes an alternative deformation mode of the nanolaminate structure. Pile-ups of interfacial dislocations occur when interfacial ledges and impinged lattice dislocations act as obstacles to impede the movement of interfacial dislocations. Deformation twinning can accordingly take place to relieve a stress concentration resulting from the pile-up of interfacial dislocations. An interface-controlled twinning mechanism driven by the pile-up and dissociation of interfacial dislocations is accordingly proposed.

Complex Hand Dexterity: A Review of Biomechanical Methods for Measuring Musical Performance

Directory of Open Access Journals (Sweden)

Cheryl Diane Metcalf

2014-05-01

Full Text Available Complex hand dexterity is fundamental to our interactions with the physical, social and cultural environment. Dexterity can be an expression of creativity and precision in a range of activities, including musical performance. Little is understood about complex hand dexterity or how virtuoso expertise is acquired, due to the versatility of movement combinations available to complete any given task. This has historically limited progress of the field because of difficulties in measuring movements of the hand. Recent developments in methods of motion capture and analysis mean it is now possible to explore the intricate movements of the hand and fingers. These methods allow us insights into the neurophysiological mechanisms underpinning complex hand dexterity and motor learning. They also allow investigation into the key factors that contribute to injury, recovery and functional compensation.The application of such analytical techniques within musical performance provides a multidisciplinary framework for purposeful investigation into the process of learning and skill acquisition in instrumental performance. These highly skilled manual and cognitive tasks present the ultimate achievement in complex hand dexterity. This paper will review methods of assessing instrumental performance in music, focusing specifically on biomechanical measurement and the associated technical challenges faced when measuring highly dexterous activities.

Comparison of defects in ProTaper hand-operated and engine-driven instruments after clinical use.

Science.gov (United States)

Cheung, G S P; Bian, Z; Shen, Y; Peng, B; Darvell, B W

2007-03-01

To compare the type of defects and mode of material failure of engine-driven and hand-operated ProTaper instruments after clinical use. A total of 401 hand-operated and 325 engine-driven ProTaper instruments were discarded from an endodontic clinic over 17 months. Those that had fractured were examined for plastic deformation in lateral view and remounted for fractographical examination in scanning electron microscope. The mode of fracture was classified as 'fatigue' or 'shear' failure. The lengths of fractured segments in both instruments were recorded. Any distortion in hand instrument was noted. Data were analysed using chi-square, Fisher's exact or Student's t-test, where appropriate. Approximately 14% of all discarded hand-operated instruments and 14% of engine-driven instruments were fractured. About 62% of hand instruments failed because of shear fracture, compared with approximately 66% of engine-driven instruments as a result of fatigue (P hand instruments were affected by shear, and either remained intact or was fractured, compared with 5% of engine-driven instruments (P hand versus engine-driven group (P hand instruments were discarded intact but distorted (rarely for engine-driven instruments); all were in the form of unscrewing of the flutes. The location of defects in hand Finishing instruments was significantly closer to the tip than that for Shaping instruments (P ProTaper engine-driven and hand-operated instruments appeared to be different, with shear failure being more prevalent in the latter.

Cooperating the BDS, GPS, GLONASS and strong-motion observations for real-time deformation monitoring

Science.gov (United States)

Tu, Rui; Liu, Jinhai; Lu, Cuixian; Zhang, Rui; Zhang, Pengfei; Lu, Xiaochun

2017-06-01

An approach of cooperating the BDS, GPS, GLONASS and strong-motion (SM) records for real-time deformation monitoring was presented, which was validated by the experimental data. In this approach, the Global Navigation Satellite System (GNSS) data were processed with the real-time kinematic positioning technology to retrieve the GNSS displacement, and the SM data were calibrated to acquire the raw acceleration; a Kalman filter was then applied to combine the GNSS displacement and the SM acceleration to obtain the integrated displacement, velocity and acceleration. The validation results show that the advantages of each sensor are completely complementary. For the SM, the baseline shifts are estimated and corrected, and the high-precision velocity and displacement are recovered. While the noise of GNSS can be reduced by using the SM-derived high-resolution acceleration, thus the high-precision and broad-band deformation information can be obtained in real time. The proposed method indicates a promising potential and capability in deformation monitoring of the high-building, dam, bridge and landslide.

The role of simultaneous gap arthroplasty and distraction osteogenesis in the management of temporo-mandibular joint ankylosis with mandibular deformity in children.

Science.gov (United States)

Rao, Krishna; Kumar, Sudhir; Kumar, Vijay; Singh, Arun Kumar; Bhatnagar, Sudhir Kumar

2004-02-01

Temporo-mandibular joint ankylosis is a common cause of acquired deformity in children. Surgical correction of the ankylosis only leaves the patient with an uncorrected mandibular deformity. This study was to evaluate the use of distraction osteogenesis for simultaneous correction of the mandibular deformity. This study was done on six children with temporo-mandibular joint ankylosis and mandibular deformity. Uniaxial double pin distractors with Schanz pins were used in this study. The patients underwent simultaneous gap arthroplasty and mandibular osteotomy (retromolar) with distractor insertion. Distraction was started on the fifth post-operative day. The patients were put on dynamic temporo-mandibular joint exercises on the first post-operative day. All patients had a satisfactory mouth opening on follow-up. Satisfactory cosmetic correction of the mandibular deformity was also achieved in all these patients. Some degree of malocclusion resulted from treatment due to which the patients were placed on orthodontic treatment. Distraction osteogenesis can be used simultaneously with gap arthroplasty in patients with temporo-mandibular ankylosis, for the correction of the mandibular deformity.

Political Left and Right: Our Hands-On Logic

Directory of Open Access Journals (Sweden)

Frits Bienfait

2014-12-01

Full Text Available The origins and immediate vitality of the left/right divide which emerged in French revolutionary politics from 1789 can only be understood against the background of a much older classification dynamic based on the primacy of the right hand, first described by Robert Hertz in 1909. This dynamic infused political thinking first in Versailles and since 1815 in democracies throughout the world. In the process, the classical left/right polarity acquired a new dimension: the complementary notions of ‘accepting’ and ‘questioning’ the existing social order. An essential feature of both the age-old classical polarity and the ensuing political polarity is that they are intimately bound up with local and evolving social contexts: there is no single content-based definition of left and right. As long as the majority of us are predisposed to use our right hand when acting in the world, ‘left versus right’ will remain the most important political antithesis in western-type democracies.

Multi-scale analysis of deformation behavior at SCC crack tip (3) (Contract research)

International Nuclear Information System (INIS)

Kaji, Yoshiyuki; Miwa, Yukio; Tsukada, Takashi; Hayakawa, Masao; Nagashima, Nobuo

2008-08-01

In recent years, incidents of the stress corrosion cracking (SCC) were frequently reported that occurred to the various components of domestic boiling water reactors (BWR), and the cause investigation and measure become the present important issue. By the Japan nuclear energy safety organization (JNES), a research project on the intergranular SCC (IGSCC) in nuclear grade stainless steels (henceforth, IGSCC project) is under enforcement from a point of view to secure safety and reliability of BWR, and SCC growth data of low carbon stainless steels are being accumulated for the weld part or the work-hardened region adjacent to the weld metal. In the project, it has been an important subject to guarantee the validity of accumulated SCC data. At a crack tip of SCC in compact tension (CT) type specimen used for the SCC propagation test, a macroscopic plastic region is formed where heterogeneity of microstructure developed by microscopic sliding and dislocations is observed. However, there is little quantitative information on the plastic region, and therefore, to assess the data of macroscopic SCC growth rate and the validity of propagation test method, it is essentially required to investigate the plastic region at the crack tip in detail from a microscopic viewpoint. This report describes a result of the research conducted by the Japan Atomic Energy Agency and the National Institute for Materials Science under contract with JNES that was concerned with a multi-scale analysis of plastic deformation behavior at the crack tip of SCC. The research was carried out to evaluate the validity of the SCC growth data acquired in the IGSCC project based on a mechanistic understanding of SCC. For the purpose, in this research, analyses of the plastic deformation behavior and microstructure around the crack tip were performed in a nano-order scale. The hardness measured in nano, meso and macro scales was employed as a common index of the strength, and the essential data necessary

Concomitant Appearance of Pisa Syndrome and Striatal Hand in Parkinson’s Disease

Directory of Open Access Journals (Sweden)

Sanjay Pandey

2011-10-01

Full Text Available Pisa syndrome is (PS usually seen in patients receiving antipsychotic drugs and characterised by lateral flexion of trunk and axial dystonia. It is believed that antipsychotic drugs lead to dopamine blockage causing PS. We describe a Parkinson’s disease patient who was doing well with levodopa/carbidopa for 3 years and developed lateral flexion of trunk. His abnormal posture used to completely improve upon lying down position. He also had striatal hand deformity suggestive of focal dystonia.

Characterization of local plastic instability during deformation of D9 clad tubes for fast breeder nuclear fuel by infrared thermography

International Nuclear Information System (INIS)

Kapoor, K.; Somasekhar Reddy, K.; Ramana Rao, A.V.

2009-01-01

Plastic instability is a condition occurring ahead of ductile fracture in materials subjected to deformation. This condition is a warning before the final failure occurring by ductile fracture. This condition manifests during necking in tensile deformation and crack propagation during plastic deformation. Early detection of such a condition can prevent permanent damage. In the present case, a novel approach by use of infrared thermography is proposed for characterization of local plastic instability during deformation of D9 clad tube material. Infrared thermal imaging was used for acquiring data during deformation by plug drawing, pilgering and uniaxial tension tests. The local plastic instability due to propagation of defects was monitored by use of Taylor-Quinney coefficient (β). Where, the Taylor-Quinney coefficient is defined as the ratio of plastic work converted into heat, which was evaluated by using thermal imaging data. In our study, an analysis of the heat generated during the process of plastic deformation was measured thereby correlating the abnormal temperature variations with the defects appearing in the material. In our study, an analysis of the heat generated during the process of plastic deformation was measured thereby correlating the abnormal temperature variations with the defects appearing in the material

Contribution of deformation to sea-ice mass balance: a case study from an N-ICE2015 storm

DEFF Research Database (Denmark)

Itkin, Polona; Spreen, Gunnar; Hvidegaard, Sine Munk

2018-01-01

The fastest and most efficient process of gaining sea ice volume is through the mechanical redistribution of mass as a consequence of deformation events. During the ice growth season divergent motion produces leads where new ice grows thermodynamically, while convergent motion fractures the ice...... and either piles the resultant ice blocks into ridges or rafts one floe under the other. Here we present an exceptionally detailed airborne dataset from a 9km2 area of first and second year ice in the Transpolar Drift north of Svalbard that allowed us to estimate the redistribution of mass from an observed...... deformation event. To achieve this level of detail we analyzed changes in sea ice freeboard acquired from two airborne laser scanner surveys just before and right after a deformation event brought on by a passing low pressure system. A linear regression model based on divergence during this storm can explain...

Using environmental engineering to increase hand hygiene compliance: a cross-over study protocol.

Science.gov (United States)

Schmidtke, Kelly Ann; Aujla, Navneet; Marshall, Tom; Hussain, Abid; Hodgkinson, Gerard P; Arheart, Kristopher; Marti, Joachim; Birnbach, David J; Vlaev, Ivo

2017-09-11

Compliance with hand hygiene recommendations in hospital is typically less than 50%. Such low compliance inevitably contributes to hospital-acquired infections that negatively affect patients' well-being and hospitals' finances. The design of the present study is predicated on the assumption that most people who fail to clean their hands are not doing so intentionally, they just forget. The present study will test whether psychological priming can be used to increase the number of people who clean their hands on entering a ward. Here, we present the protocol for this study. The study will use a randomised cross-over design. During the study, each of four wards will be observed during four conditions: olfactory prime, visual prime, both primes and neither prime. Each condition will be experienced for 42 days followed by a 7-day washout period (total duration of trial=189 days). We will record the number of people who enter each ward and whether they clean their hands during observation sessions, the amount of cleaning material used from the dispensers each week and the number of hospital-acquired infections that occur in each period. The outcomes will be compared using a regression analysis. Following the initial trail, the most effective priming condition will be rolled out for 3 months in all the wards. Research ethics approval was obtained from the South Central-Oxford C Research Ethics Committee (16/SC/0554), the Health Regulatory Authority and the sponsor. ISRCTN (15397624); Edge ID 86357. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Method of Monitoring Urban Area Deformation Based on Differential TomoSAR

Directory of Open Access Journals (Sweden)

WANG Aichun

2016-12-01

Full Text Available While the use of differential TomoSAR based on compressive sensing (CS makes it possible to solve the layover problem and reconstruct the deformation information of an observed urban area scene acquired by moderate-high resolution SAR satellite, the performance of the reconstruction decreases for a sparse and structural observed scene due to ignoring the structural characteristics of the observed scene. To deal with this issue, the method for differential SAR tomography based on Khatri-Rao subspace and block compressive sensing (KRS-BCS is proposed. The proposed method changes the reconstruction of the sparse and structural observed scene into a BCS problem under Khatri-Rao subspace, using the structure information of the observed scene and Khatri-Rao product property of the reconstructed observation matrix for differential TomoSAR, such that the KRS-BCS problem is efficiently solved with a block sparse l1/l2 norm optimization signal model, and the performance of resolution capability and reconstruction estimation is compared and analyzed qualitatively and quantitatively by the theoretical analysis and the simulation experiments, all of the results show the propose KRS-BCS method practicably overcomes the problems of CS method, as well as, quite maintains the high resolution characteristics, effectively reduces the probability of false scattering target and greatly improves the reconstruction accurate of scattering point. Finally, the application is taking the urban area of the Mobara(in Chiba, Japan as the test area and using 34 ENVISAT-ASAR images, the accuracy is verifying with the reference deformations derived from first level point data and GPS tracking data, the results show the trend is consistent and the overall deviation is small between reconstruction deformations of the propose KRS-BCS method and the reference deformations, and the accuracy is high in the estimation of the urban area deformation.

Effect of initial grain size on inhomogeneous plastic deformation and twinning behavior in high manganese austenitic steel with a polycrystalline microstructure

Science.gov (United States)

Ueji, R.; Tsuchida, N.; Harada, K.; Takaki, K.; Fujii, H.

2015-08-01

The grain size effect on the deformation twinning in a high manganese austenitic steel which is so-called TWIP (twining induced plastic deformation) steel was studied in order to understand how to control deformation twinning. The 31wt%Mn-3%Al-3% Si steel was cold rolled and annealed at various temperatures to obtain fully recrystallized structures with different mean grain sizes. These annealed sheets were examined by room temperature tensile tests at a strain rate of 10-4/s. The coarse grained sample (grain size: 49.6μm) showed many deformation twins and the deformation twinning was preferentially found in the grains in which the tensile axis is parallel near to [111]. On the other hand, the sample with finer grains (1.8 μm) had few grains with twinning even after the tensile deformation. The electron back scattering diffraction (EB SD) measurements clarified the relationship between the anisotropy of deformation twinning and that of inhomogeneous plastic deformation. Based on the EBSD analysis, the mechanism of the suppression of deformation twinning by grain refinement was discussed with the concept of the slip pattern competition between the slip system governed by a grain boundary and that activated by the macroscopic load.

Performance Comparison Between FEDERICA Hand and LARM Hand

OpenAIRE

Carbone, Giuseppe; Rossi, Cesare; Savino, Sergio

2015-01-01

This paper describes two robotic hands that have been\\ud developed at University Federico II of Naples and at the\\ud University of Cassino. FEDERICA Hand and LARM Hand\\ud are described in terms of design and operational features.\\ud In particular, careful attention is paid to the differences\\ud between the above-mentioned hands in terms of transmission\\ud systems. FEDERICA Hand uses tendons and pulleys\\ud to drive phalanxes, while LARM Hand uses cross four-bar\\ud linkages. Results of experime...

Back to basics: hand hygiene and surgical hand antisepsis.

Science.gov (United States)

Spruce, Lisa

2013-11-01

Health care-associated infections (HAIs) are a significant issue in the United States and throughout the world, but following proper hand hygiene practices is the most effective and least expensive way to prevent HAIs. Hand hygiene is inexpensive and protects patients and health care personnel alike. The four general types of hand hygiene that should be performed in the perioperative environment are washing hands that are visibly soiled, hand hygiene using alcohol-based products, surgical hand scrubs, and surgical hand scrubs using an alcohol-based surgical hand rub product. Barriers to proper hand hygiene may include not thinking about it, forgetting, skin irritation, a lack of role models, or a lack of a safety culture. One strategy for improving hand hygiene practices is monitoring hand hygiene as part of a quality improvement project, but the most important aspect for perioperative team members is to set an example for other team members by following proper hand hygiene practices and reminding each other to perform hand hygiene. Copyright © 2013 AORN, Inc. Published by Elsevier Inc. All rights reserved.

The 2006-2012 deformation at Sakurajima stratovolcano (Japan) detected via spaceborne multisensor SAR Interferometry

Science.gov (United States)

Pepe, Susi; Trippanera, Daniele; Casu, Francesco; Tizzani, Pietro; Nobile, Adriano; Aoki, Yosuke; Zoffoli, Simona; Acocella, Valerio; Sansosti, Eugenio

2013-04-01

We analyze the evolution of the ground deformation at Sakurajima active stratovolcano located in the Aira caldera (Kagoshima prefecture Japan). This caldera, extending over more than 20 km, has been formed as a consequence of a huge eruption, occurred 22,000 years ago, that caused a magma chamber collapse. The Sakurajima volcano is an andesitic cone formed by more recent activity within the caldera, beginning about 13,000 years ago. Its first historical recorded eruption occurred in 963 AD. Most eruptions are Strombolian and Vulcanian and affect only the summit area. The larger explosive (plinian) eruptions occurred in 1471-1476, 1779-1782 and 1914, each producing 1 - 2 km3 of lava and pyroclastic materials. Explosive eruptions of Vulcanian type, with ash emissions, have occurred intermittently from 1955 to 2002. From 2009 to December 2012, a strong and continuous period of volcanic activity has been recorded mainly at the Showa Crater producing plumes that reached altitudes of 1.8-3.5 km. In order to analyze the active deformation processes of the volcano complex and its surrounding areas, we performed SAR Interferometry (InSAR) techniques by using COSMOSkyMed (X-band) and ALOS (L-band) data. The joint data analysis allowed us to increase the spatial coverage of InSAR measurements., we processed 19 descending and 25 ascending orbit SAR images acquired by ALOS satellite from 2008 to 2011 and 2006 to 2011, respectively; we computed 57 descending and 71 ascending interferograms which were subsequently inverted via SBAS-InSAR algorithm to obtain mean velocity maps and deformation time series. The X-band dataset consists of 20 images acquired only on descending orbits between 2011 and 2012; from this dataset we computed 44 interferograms. The preliminary analysis of the mean deformation velocity reveals the presence of a consistent uplift signal in the North region of the Sakurajima Island that extends also to the North sector of Kagoshima bay. The corresponding

Development of Multiorgan Finite Element-Based Prostate Deformation Model Enabling Registration of Endorectal Coil Magnetic Resonance Imaging for Radiotherapy Planning

International Nuclear Information System (INIS)

Hensel, Jennifer M.; Menard, Cynthia; Chung, Peter W.M.; Milosevic, Michael F.; Kirilova, Anna; Moseley, Joanne L.; Haider, Masoom A.; Brock, Kristy K.

2007-01-01

Purpose: Endorectal coil (ERC) magnetic resonance imaging (MRI) provides superior visualization of the prostate compared with computed tomography at the expense of deformation. This study aimed to develop a multiorgan finite element deformable method, Morfeus, to accurately co-register these images for radiotherapy planning. Methods: Patients with prostate cancer underwent fiducial marker implantation and computed tomography simulation for radiotherapy planning. A series of axial MRI scans were acquired with and without an ERC. The prostate, bladder, rectum, and pubic bones were manually segmented and assigned linear elastic material properties. Morfeus mapped the surface of the bladder and rectum between two imaged states, calculating the deformation of the prostate through biomechanical properties. The accuracy of deformation was measured as fiducial marker error and residual surface deformation between the inferred and actual prostate. The deformation map was inverted to deform from 100 cm 3 to no coil. Results: The data from 19 patients were analyzed. Significant prostate deformation occurred with the ERC (mean intrapatient range, 0.88 ± 0.25 cm). The mean vector error in fiducial marker position (n = 57) was 0.22 ± 0.09 cm, and the mean vector residual surface deformation (n = 19) was 0.15 ± 0.06 cm for deformation from no coil to 100-cm 3 ERC, with an image vector resolution of 0.22 cm. Accurately deformed MRI scans improved soft-tissue resolution of the anatomy for radiotherapy planning. Conclusions: This method of multiorgan deformable registration enabled accurate co-registration of ERC-MRI scans with computed tomography treatment planning images. Superior structural detail was visible on ERC-MRI, which has potential for improving target delineation

Is nucleon deformed?

International Nuclear Information System (INIS)

Abbas, Afsar

1992-01-01

The surprising answer to this question Is nucleon deformed? is : Yes. The evidence comes from a study of the quark model of the single nucleon and when it is found in a nucleus. It turns out that many of the long standing problems of the Naive Quark Model are taken care of if the nucleon is assumed to be deformed. Only one value of the parameter P D ∼1/4 (which specifies deformation) fits g A (the axial vector coupling constant) for all the semileptonic decay of baryons, the F/D ratio, the pion-nucleon-delta coupling constant fsub(πNΔ), the double delta coupling constant 1 fsub(πΔΔ), the Ml transition moment μΔN and g 1 p the spin structure function of proton 2 . All this gives strong hint that both neutron and proton are deformed. It is important to look for further signatures of this deformation. When this deformed nucleon finds itself in a nuclear medium its deformation decreases. So much that in a heavy nucleus the nucleons are actually spherical. We look into the Gamow-Teller strengths, magnetic moments and magnetic transition strengths in nuclei to study this property. (author). 15 refs

Whole-field macro- and micro-deformation characteristic of unbound water-loss in dentin hard tissue.

Science.gov (United States)

Chen, Zhenning; Nadeau, Bobby; Yu, Kevin; Shao, Xinxing; He, Xiaoyuan; Goh, M Cynthia; Kishen, Anil

2018-04-06

High-resolution deformation measurements in a functionally graded hard tissue such as human dentin are essential to understand the unbound water-loss mediated changes and their role in its mechanical integrity. Yet a whole-field, 3-dimensional (3D) measurement and characterization of fully hydrated dentin in both macro- and micro-scales remain to be a challenge. This study was conducted in 2 stages. In stage-1, a stereo-digital image correlation approach was utilized to determine the water-loss and load-induced 3D deformations of teeth in a sagittal section over consecutively acquired frames, from a fully hydrated state to nonhydrated conditions for a period up to 2 hours. The macroscale analysis revealed concentrated residual deformations at the dentin-enamel-junction and the apical regions of root in the direction perpendicular to the dentinal tubules. Significant difference in the localized deformation characteristics was observed between the inner and outer aspects of the root dentin. During quasi-static loadings, further increase in the residual deformation was observed in the dentin. In stage-2, dentin microstructural variations induced by dynamic water-loss were assessed with environmental scanning electron microscopy and atomic force microscopy (AFM), showing that the dynamic water-loss induced distention of dentinal tubules with concave tubular edges, and concurrent contraction of intertubular dentin with convex profile. The findings from the current macro- and micro-scale analysis provided insight on the free-water-loss induced regional deformations and ultrastructural changes in human dentin. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Stiff Hands

Science.gov (United States)

... All Topics A-Z Videos Infographics Symptom Picker Anatomy Bones Joints Muscles Nerves Vessels Tendons About Hand Surgery What is a Hand Surgeon? What is a Hand Therapist? Media Find a Hand Surgeon Home Anatomy Stiff Hands Email to a friend * required fields ...

Hand Infections

Science.gov (United States)

... All Topics A-Z Videos Infographics Symptom Picker Anatomy Bones Joints Muscles Nerves Vessels Tendons About Hand Surgery What is a Hand Surgeon? What is a Hand Therapist? Media Find a Hand Surgeon Home Anatomy Hand Infections Email to a friend * required fields ...

[Bertha Röntgen or the transparency of the hand].

Science.gov (United States)

Picard, J D

1996-01-01

It is to Wilhelm Conrad Röntgen, the first elected "radiologist" of our Academy and the first Nobel Prize winner in physics, that we owe the transparency of the hand. We celebrate today the centenary of the great scientific discovery which was to revolutionize the diagnosis, and thereby the treatment, of a large number of illnesses the discovery of X-rays. It would be unjust not to link the name of this scientist with that of his wife, Bertha, who, ignorant of the dangers of all "novel medical inventions" volunteered her own hand for his research experiments: the hand which was to bring to the world tangible proof of this remarkable discovery. To a lesser degree, but nonetheless essential, we acknowledge, albeit not in exhaustive detail, all the progress made by the work of pioneers using this new investigative technique. So let us now return to the hand:--a body part which it was easy to immobilize, remembering that in those days a single radiographic exposure took up to an hour to obtain,--we will consider the immortalised hand of Bertha Röntgen,---to whom this address is dedicated,---and its radiographic exposures which allow us to appreciate the advances and to perceive the limitations of this technique. They also enable us better to envisage future investigative approaches whereby a deeper knowledge of the human body may be acquired. We note that compared with the histopathological sciences, imaging is not specific. Numerous microscopic structures, in particular neurological and vascular ones, are still insufficiently well visualised and the transmission pathways between the hand and the central nervous system deserve better characterisation. Current, research programmes are attempting to overcome these limitation of modern imaging. All the experience gained in studying the transparency of the hand, as we have discussed, is applicable to every part of the human anatomy. To credit: Röntgen's discovery with all its originality, we could say that the hand was

Bacteriological aspects of hand washing: A key for health promotion and infections control

Directory of Open Access Journals (Sweden)

Ramezan Ali Ataee

2017-01-01

Full Text Available The aim of this review is to show the historical aspects of hands washing for healthy life and explains how can reduce the transmission of community-acquired infectious agents by healthcare workers and patients. This review article is prepared based on available database. The key words used were hands washing, risk assessment, hands hygiene, bacterial flora, contamination, infection, nosocomial, tap water, sanitizer, bacterial resistance, hands bacterial flora, washing methods, antiseptics, healthcare workers, healthcare personnel, from PubMed, ScienceDirect, Embase, Scopus, Web of Sciences, and Google Scholar. Data were descriptively analyzed. The insistence on hand washing has a history of 1400 years. The research results indicate that the bacteria released from the female washed hands in wet and dry condition was lower than from the male′s hands with a significance level (3 CFU vs. 8 CFU; confidence interval 95%, P ≤ 0.001. The valuable results of the study indicated that released amount of bacterial flora from wet hands is more than 10 times in compared to dry hands. In addition, established monitoring systems for washing hands before and after patient′s manipulation as well as after toilet were dominant indices to prevent the transfer of infectious agents to the patients. Increasing awareness and belief of the healthcare workers have shown an important role by about 30% reduction in the transfection. Hand washing could reduce the episodes of transmission of infectious agents in both community and healthcare settings. However, hand washing is an important key factor to prevent transmission of infectious agents to patients. There is no standard method for measuring compliance. Thus, permanent monitoring of hand washing to reduce the transmission of infections is crucial. Finally, the personnel must believe that hand washing is an inevitable approach to infection control.

Comparison of KVCBCT based on deformable image registration of adaptive planning and static 3DCRT planning for patients with lung cancer

International Nuclear Information System (INIS)

Hou Yong; Yin Yong; Wang Pengcheng; Ma Chengsheng

2012-01-01

Objective: To comparison of kilo-voltage cone-beam CT (KVCBCT) deformable image registration of adaptive planning and static planning for patients with lung cancer,and evaluate their characters. Methods: Five patients with lung cancer were in the study. Two sets image were acquired every three days and were concatenated to one set. Ten sets CBCT image and planning CT image were transferred a commercial deformable image registration software. The planning CT was deformed to each set CBCT and the contours delineated, the new contour were labeled CBCT f1 -CBCT f10 . Transfer of each deformed planning CT and CBCT f1 -CBCT f10 back into the treatment planning system enable re-calculation of actual dose distribution, then we obtain CT planning and fractional CBCT contour planning, the CBCT planning were labeled CBCT p1 -CBCT p10 . Ten times CBCT planning of every patient were added to acquire a total dose accumulation planning (DA plan), comparison of dose distribution and dose-volume histogram in CT plan and DA plan for fractionation dose and accumulation dose of left, right, total lung, PTV and spinal-cord. The difference of two plan was analyzed by Wilcoxson's sign rank test. Results: The max and min dose of PTV, the left, right, total lung V 5 , V 10 , V 20 , V 30 , V 50 , spinal-cord max dose, and the left,right and total lung mean dose in DA plan were smaller than in CT plan (z=-2.02 - -2.03, P 95 in DA plan was as well as in CT plan (z=-1.48, -1.21, P=0.138, 0.225). Conclusions: KVCBCT based deformable image registration of adaptive planning reduce the dose of lung and spinal-cord, and enhance the dose of PTV. This provides a tool for exploring adaptive radiotherapy strategies. (authors)

Sea Ice Deformation State From Synthetic Aperture Radar Imagery - Part II: Effects of Spatial Resolution and Noise Level

DEFF Research Database (Denmark)

Dierking, Wolfgang; Dall, Jørgen

2008-01-01

C- and L-band airborne synthetic aperture radar (SAR) imagery acquired at like- and cross-polarization over sea ice under winter conditions is examined with the objective to study the discrimination between level ice and ice deformation features. High-resolution low-noise data were analysed...... in the first paper. In this second paper, the main topics are the effects of spatial resolution and signal-to-noise ratio. Airborne, high-resolution SAR scenes are used to generate a sequence of images with increasingly coarser spatial resolution from 5 m to 25 m, keeping the number of looks constant....... The signal-to-noise ratio is varied between typical noise levels for airborne imagery and satellite data. Areal fraction of deformed ice and average deformation distance are determined for each image product. At L-band, the retrieved values of the areal fraction get larger as the image resolution is degraded...

Ongoing Deformation of Sinkholes in Wink, Texas, Observed by Time-Series Sentinel-1A SAR Interferometry (Preliminary Results

Directory of Open Access Journals (Sweden)

Jin-Woo Kim

2016-04-01

Full Text Available Spatiotemporal deformation of existing sinkholes and the surrounding region in Wink, TX are probed using time-series interferometric synthetic aperture radar (InSAR methods with radar images acquired from the Sentinel-1A satellite launched in April 2014. The two-dimensional deformation maps, calculated using InSAR observations from ascending and descending tracks, reveal that much of the observed deformation is vertical. Our results indicate that the sinkholes are still influenced by ground depression, implying that the sinkholes continue to expand. Particularly, a region 1 km northeast of sinkhole #2 is sinking at a rate of up to 13 cm/year, and its aerial extent has been enlarged in the past eight years when compared with a previous survey. Furthermore, there is a high correlation between groundwater level and surficial subsidence during the summer months, representing the complicated characteristics of sinkhole deformation under the influence of successive roof failures in underlying cavities. We also modeled the sinkhole deformation in a homogenous elastic half-space with two dislocation sources, and the ground depression above cavities could be numerically analyzed. Measurements of ongoing deformation in sinkholes and assessments of the stability of the land surface at sinkhole-prone locations in near real-time, are essential for mitigating the threat posed to people and property by the materialization of sinkholes.

Effects of combining 2 weeks of passive sensory stimulation with active hand motor training in healthy adults.

Directory of Open Access Journals (Sweden)

Aija Marie Ladda

Full Text Available The gold standard to acquire motor skills is through intensive training and practicing. Recent studies have demonstrated that behavioral gains can also be acquired by mere exposure to repetitive sensory stimulation to drive the plasticity processes. Single application of repetitive electric stimulation (rES of the fingers has been shown to improve tactile perception in young adults as well as sensorimotor performance in healthy elderly individuals. The combination of repetitive motor training with a preceding rES has not been reported yet. In addition, the impact of such a training on somatosensory tactile and spatial sensitivity as well as on somatosensory cortical activation remains elusive. Therefore, we tested 15 right-handed participants who underwent repetitive electric stimulation of all finger tips of the left hand for 20 minutes prior to one hour of motor training of the left hand over the period of two weeks. Overall, participants substantially improved the motor performance of the left trained hand by 34%, but also showed a relevant transfer to the untrained right hand by 24%. Baseline ipsilateral activation fMRI-magnitude in BA 1 to sensory index finger stimulation predicted training outcome for somatosensory guided movements: those who showed higher ipsilateral activation were those who did profit less from training. Improvement of spatial tactile discrimination was positively associated with gains in pinch grip velocity. Overall, a combination of priming rES and repetitive motor training is capable to induce motor and somatosensory performance increase and representation changes in BA1 in healthy young subjects.

SU-E-J-195: Quantification of Rotations and Deformations in Head and Heck Radiotherapy

International Nuclear Information System (INIS)

Kim, J; Liu, C; Kumarasiri, A; Gordon, J; Siddiqui, F; Chetty, I J; Chetvertkov, M

2014-01-01

Purpose: To quantify the magnitude of patient rotations and deformations over the course of head and neck radiotherapy. Methods: 45 CBCT images acquired weekly were selected retrospectively from 5 head and neck cancer patients. CBCT images were registered to the corresponding planning CT images using translation, rigid-body, and cubic B-spline deformable transformations. Elastix ( elastix.isi.uu.nl ), an open-source public domain registration algorithm, was used for all registrations with mutual information as similarity metric and gradient descent as optimization. Four-level multiresolution approach was employed with 2 cm B-spline grid spacing at the finest resolution. Registration qualities were visually verified. Rotational occurrences were quantified from the rigid-body registrations. The magnitude of deformations in planning target volumes (PTV) and organs were quantified from the deformation vector fields with rigid registrations as baseline. Results: The measured rotations (mean±std) were 1.0±1.0 deg, - 0.3±1.0 deg, and 0.1±0.8 deg in the sagittal, coronal, and axial plains respectively. The estimated magnitudes of deformations (mean±std) were 3.4±2.1 mm for PTVs, 2.9±1.2 mm for parotid glands, 2.8±1.2 mm for mandible, and 2.2±1.1 mm for spinal cord. The overall deformation in the body contour was 4.3±4.3 mm. The organ spatial deviation due to rotation was small and approximately 8.4% of that from deformations. Results varied among patients. Conclusion: Rotations occurred about 1.0 deg (1SD) in the H'N area. Daily geometric deviation of target volumes was considerable and mainly from tissue deformation than rotations. Proper safety margin is necessary for adequate target coverage. Online plan adaptation may mitigate the daily differences between the plan and actual patient poses. Partially supported by a grant from Varian Medical Systems, Palo Alto, CA

Development of a deformable dosimetric phantom to verify dose accumulation algorithms for adaptive radiotherapy.

Science.gov (United States)

Zhong, Hualiang; Adams, Jeffrey; Glide-Hurst, Carri; Zhang, Hualin; Li, Haisen; Chetty, Indrin J

2016-01-01

Adaptive radiotherapy may improve treatment outcomes for lung cancer patients. Because of the lack of an effective tool for quality assurance, this therapeutic modality is not yet accepted in clinic. The purpose of this study is to develop a deformable physical phantom for validation of dose accumulation algorithms in regions with heterogeneous mass. A three-dimensional (3D) deformable phantom was developed containing a tissue-equivalent tumor and heterogeneous sponge inserts. Thermoluminescent dosimeters (TLDs) were placed at multiple locations in the phantom each time before dose measurement. Doses were measured with the phantom in both the static and deformed cases. The deformation of the phantom was actuated by a motor driven piston. 4D computed tomography images were acquired to calculate 3D doses at each phase using Pinnacle and EGSnrc/DOSXYZnrc. These images were registered using two registration software packages: VelocityAI and Elastix. With the resultant displacement vector fields (DVFs), the calculated 3D doses were accumulated using a mass-and energy congruent mapping method and compared to those measured by the TLDs at four typical locations. In the static case, TLD measurements agreed with all the algorithms by 1.8% at the center of the tumor volume and by 4.0% in the penumbra. In the deformable case, the phantom's deformation was reproduced within 1.1 mm. For the 3D dose calculated by Pinnacle, the total dose accumulated with the Elastix DVF agreed well to the TLD measurements with their differences <2.5% at four measured locations. When the VelocityAI DVF was used, their difference increased up to 11.8%. For the 3D dose calculated by EGSnrc/DOSXYZnrc, the total doses accumulated with the two DVFs were within 5.7% of the TLD measurements which are slightly over the rate of 5% for clinical acceptance. The detector-embedded deformable phantom allows radiation dose to be measured in a dynamic environment, similar to deforming lung tissues, supporting

SU-E-J-195: Quantification of Rotations and Deformations in Head and Heck Radiotherapy

Energy Technology Data Exchange (ETDEWEB)

Kim, J; Liu, C; Kumarasiri, A; Gordon, J; Siddiqui, F; Chetty, I J [Henry Ford Health System, Detroit, MI (United States); Chetvertkov, M [Wayne State University, Detroit, MI (United States)

2014-06-01

Purpose: To quantify the magnitude of patient rotations and deformations over the course of head and neck radiotherapy. Methods: 45 CBCT images acquired weekly were selected retrospectively from 5 head and neck cancer patients. CBCT images were registered to the corresponding planning CT images using translation, rigid-body, and cubic B-spline deformable transformations. Elastix ( elastix.isi.uu.nl ), an open-source public domain registration algorithm, was used for all registrations with mutual information as similarity metric and gradient descent as optimization. Four-level multiresolution approach was employed with 2 cm B-spline grid spacing at the finest resolution. Registration qualities were visually verified. Rotational occurrences were quantified from the rigid-body registrations. The magnitude of deformations in planning target volumes (PTV) and organs were quantified from the deformation vector fields with rigid registrations as baseline. Results: The measured rotations (mean±std) were 1.0±1.0 deg, - 0.3±1.0 deg, and 0.1±0.8 deg in the sagittal, coronal, and axial plains respectively. The estimated magnitudes of deformations (mean±std) were 3.4±2.1 mm for PTVs, 2.9±1.2 mm for parotid glands, 2.8±1.2 mm for mandible, and 2.2±1.1 mm for spinal cord. The overall deformation in the body contour was 4.3±4.3 mm. The organ spatial deviation due to rotation was small and approximately 8.4% of that from deformations. Results varied among patients. Conclusion: Rotations occurred about 1.0 deg (1SD) in the H'N area. Daily geometric deviation of target volumes was considerable and mainly from tissue deformation than rotations. Proper safety margin is necessary for adequate target coverage. Online plan adaptation may mitigate the daily differences between the plan and actual patient poses. Partially supported by a grant from Varian Medical Systems, Palo Alto, CA.

Development of a deformable dosimetric phantom to verify dose accumulation algorithms for adaptive radiotherapy

Directory of Open Access Journals (Sweden)

Hualiang Zhong

2016-01-01

Full Text Available Adaptive radiotherapy may improve treatment outcomes for lung cancer patients. Because of the lack of an effective tool for quality assurance, this therapeutic modality is not yet accepted in clinic. The purpose of this study is to develop a deformable physical phantom for validation of dose accumulation algorithms in regions with heterogeneous mass. A three-dimensional (3D deformable phantom was developed containing a tissue-equivalent tumor and heterogeneous sponge inserts. Thermoluminescent dosimeters (TLDs were placed at multiple locations in the phantom each time before dose measurement. Doses were measured with the phantom in both the static and deformed cases. The deformation of the phantom was actuated by a motor driven piston. 4D computed tomography images were acquired to calculate 3D doses at each phase using Pinnacle and EGSnrc/DOSXYZnrc. These images were registered using two registration software packages: VelocityAI and Elastix. With the resultant displacement vector fields (DVFs, the calculated 3D doses were accumulated using a mass-and energy congruent mapping method and compared to those measured by the TLDs at four typical locations. In the static case, TLD measurements agreed with all the algorithms by 1.8% at the center of the tumor volume and by 4.0% in the penumbra. In the deformable case, the phantom's deformation was reproduced within 1.1 mm. For the 3D dose calculated by Pinnacle, the total dose accumulated with the Elastix DVF agreed well to the TLD measurements with their differences <2.5% at four measured locations. When the VelocityAI DVF was used, their difference increased up to 11.8%. For the 3D dose calculated by EGSnrc/DOSXYZnrc, the total doses accumulated with the two DVFs were within 5.7% of the TLD measurements which are slightly over the rate of 5% for clinical acceptance. The detector-embedded deformable phantom allows radiation dose to be measured in a dynamic environment, similar to deforming lung

Influence of Action-Effect Associations Acquired by Ideomotor Learning on Imitation

Science.gov (United States)

Bunlon, Frédérique; Marshall, Peter J.; Quandt, Lorna C.; Bouquet, Cedric A.

2015-01-01

According to the ideomotor theory, actions are represented in terms of their perceptual effects, offering a solution for the correspondence problem of imitation (how to translate the observed action into a corresponding motor output). This effect-based coding of action is assumed to be acquired through action-effect learning. Accordingly, performing an action leads to the integration of the perceptual codes of the action effects with the motor commands that brought them about. While ideomotor theory is invoked to account for imitation, the influence of action-effect learning on imitative behavior remains unexplored. In two experiments, imitative performance was measured in a reaction time task following a phase of action-effect acquisition. During action-effect acquisition, participants freely executed a finger movement (index or little finger lifting), and then observed a similar (compatible learning) or a different (incompatible learning) movement. In Experiment 1, finger movements of left and right hands were presented as action-effects during acquisition. In Experiment 2, only right-hand finger movements were presented during action-effect acquisition and in the imitation task the observed hands were oriented orthogonally to participants’ hands in order to avoid spatial congruency effects. Experiments 1 and 2 showed that imitative performance was improved after compatible learning, compared to incompatible learning. In Experiment 2, although action-effect learning involved perception of finger movements of right hand only, imitative capabilities of right- and left-hand finger movements were equally affected. These results indicate that an observed movement stimulus processed as the effect of an action can later prime execution of that action, confirming the ideomotor approach to imitation. We further discuss these findings in relation to previous studies of action-effect learning and in the framework of current ideomotor approaches to imitation. PMID:25793755

Variation of martensite lath width and precipitate size during creep deformation in a 10Cr-Mo steel

International Nuclear Information System (INIS)

Kim, S. H.; Song, B. Z.; Lu, W. S.

2001-01-01

The relationship between creep deformation and microstructural changes in martensitic 10Cr-MoW steel has been studied. Transmission electron microscopy and image analyser were used to determine the variation of precipitates and martensite lath width size during creep deformation and aging. As precipitates are coarsened during creep deformation, dislocations become easy to move and the recovery proceeds rapidly. This leads to the growth of lath width. The average size of precipitates was linearly increased with creep time. On the other hand the growth rate of lath width is constant until tertiary creep, but the growth of lath width is accelerated during tertiary creep. It has been concluded that the growth behavior of lath width are consistent with creep deformation. Because the growth of lath width is controlled by the coarsening of precipitates it is important to form more stable precipitates in creep condition for improvement of creep properties of martensitie steel. Microstructure of martensitic steel is thermally very stable, so the size of precipitates and martensite lath width are hardly changed during aging

Image-based Modeling of PSF Deformation with Application to Limited Angle PET Data

Science.gov (United States)

Matej, Samuel; Li, Yusheng; Panetta, Joseph; Karp, Joel S.; Surti, Suleman

2016-01-01

The point-spread-functions (PSFs) of reconstructed images can be deformed due to detector effects such as resolution blurring and parallax error, data acquisition geometry such as insufficient sampling or limited angular coverage in dual-panel PET systems, or reconstruction imperfections/simplifications. PSF deformation decreases quantitative accuracy and its spatial variation lowers consistency of lesion uptake measurement across the imaging field-of-view (FOV). This can be a significant problem with dual panel PET systems even when using TOF data and image reconstruction models of the detector and data acquisition process. To correct for the spatially variant reconstructed PSF distortions we propose to use an image-based resolution model (IRM) that includes such image PSF deformation effects. Originally the IRM was mostly used for approximating data resolution effects of standard PET systems with full angular coverage in a computationally efficient way, but recently it was also used to mitigate effects of simplified geometric projectors. Our work goes beyond this by including into the IRM reconstruction imperfections caused by combination of the limited angle, parallax errors, and any other (residual) deformation effects and testing it for challenging dual panel data with strongly asymmetric and variable PSF deformations. We applied and tested these concepts using simulated data based on our design for a dedicated breast imaging geometry (B-PET) consisting of dual-panel, time-of-flight (TOF) detectors. We compared two image-based resolution models; i) a simple spatially invariant approximation to PSF deformation, which captures only the general PSF shape through an elongated 3D Gaussian function, and ii) a spatially variant model using a Gaussian mixture model (GMM) to more accurately capture the asymmetric PSF shape in images reconstructed from data acquired with the B-PET scanner geometry. Results demonstrate that while both IRMs decrease the overall uptake

Hands-on-Universe, Europe Bringing frontline interactive astronomy to the classroom

Science.gov (United States)

Ferlet, R.

Hands-on-Universe, Europe (EU-HOU) aims at re-awakening the interest for science in the young generations through astronomy and new technologies. It relies on real observations acquired through a worldwide internet-based network of automatic telescopes or with didactical tools (webcam, radiotelescope). Pupils manipulate images in the classroom environment, using specific software within pedagogical resources constructed in close collaboration between researchers and teachers. EU-HOU is freely available on the web, and trains european teachers.

Non-invasive imaging of zebrafish with spinal deformities using optical coherence tomography: a preliminary study

Science.gov (United States)

Bernstein, Liane; Beaudette, Kathy; Patten, Kessen; Beaulieu-Ouellet, Émilie; Strupler, Mathias; Moldovan, Florina; Boudoux, Caroline

2013-03-01

A zebrafish model has recently been introduced to study various genetic mutations that could lead to spinal deformities such as scoliosis. However, current imaging techniques make it difficult to perform longitudinal studies of this condition in zebrafish, especially in the early stages of development. The goal of this project is to determine whether optical coherence tomography (OCT) is a viable non-invasive method to image zebrafish exhibiting spinal deformities. Images of both live and fixed malformed zebrafish (5 to 21 days postfertilization) as well as wild-type fish (5 to 29 days postfertilization) were acquired non-invasively using a commercial SD-OCT system, with a laser source centered at 930nm (λ=100nm), permitting axial and lateral resolutions of 7 and 8μm respectively. Using two-dimensional images and three-dimensional reconstructions, it was possible to identify the malformed notochord as well as deformities in other major organs at different stages of formation. Visualization of the notochord was facilitated with the development of a segmentation algorithm. OCT images were compared to HE histological sections and images obtained by calcein staining. Because of the possibility of performing longitudinal studies on a same fish and reducing image processing time as compared with staining techniques and histology, the use of OCT could facilitate phenotypic characterization in studying genetic factors leading to spinal deformities in zebrafish and could eventually contribute to the identification of the genetic causes of spinal deformities such as scoliosis.

Diagnosis of fetal congenital limb deformities by MRI

International Nuclear Information System (INIS)

Dong Suzhen; Zhu Ming; Zhong Yumin; Zhang Hong; Mao Jianping

2008-01-01

Objective: To explore the diagnostic value of MRI on fetal congenital limb deformities. Methods: Sixteen pregnant women, aged from 22 to 40 years (average 29 years) and with gestation from 22 to 39 weeks (average 29 weeks) were studied with a 1.5 T superconductive MR unit within 24 to 48 hours after ultrasound studies. Acquisitions consisted of coronal, sagittal, and axial slices relative to the fetal brain, spine, thorax, abdomen, especially limbs using 2D FIESTA sequences. Prenatal US and MR imaging findings were compared with postnatal diagnoses (4 fetuses) or autopsy (12 pregnant women, 13 fetuses). Postnatal evaluation included US, MR imaging, computed tomography, and physical examination. Results: Of the sixteen pregnant women (15 with a single fetus and 1 with twin fetuses), 17 fetuses were found. Those limb deformities of sixteen pregnant women included congenital both upper extremities amelia (1 case), sirenomelia sequence (1 case), micromelia (5 cases, 1 of which were twins), bilateral clenched hands (2 cases), right polydactyly (1 case), simple right ectrodactyly (1 case), right dactylolysis(1 case), simple club foot (2 cases), hydrocele spinalis with club foot (2 cases), 1 of the 2 cases with bilateral clinodactyly. In 14 of 16 cases, the diagnoses established by MR imaging were correct when compared with postnatal diagnosis, and prenatal MR diagnosis was inaccurate in 2 cases. Conclusion: Prenatal MRI is effective in the assessment of congenital limb deformities of fetuses, it can yield information additional to that obtained with US, and further correct US diagnosis. (authors)

Evaluating the effectiveness of real-time feedback on the bedside hand hygiene behaviors of nursing students.

Science.gov (United States)

Ott, Lora K; Irani, Vida R

2015-05-01

Traditional hand hygiene teaching methods lack long-term effectiveness. A longitudinal, within-subject design explored the influence of real-time hand microbe feedback and a critical-thinking decision exercise on nursing student hand hygiene behaviors. In three community hospitals, the students' (n = 68) hand swabs were tested for normal flora, methicillin-resistant Staphylococcus aureus (MRSA), and vancomycin-resistant Enterococcus at three time points. Students completed the Partnering to Heal (PTH) online exercise on hospital-acquired infection prevention decisions. Normal flora colony counts decreased across the semester and MRSA-positive cultures increased in frequency and colony counts. MRSA-positive cultures were not associated with caring for patients in isolation precautions. Significantly higher colony counts were noted in the students who completed the PTH than those who did not complete the PTH. This study explores innovative pedagogy bringing the nonvisible microbial risk to the consciousness of nursing students in an attempt to change hand hygiene behaviors. Copyright 2015, SLACK Incorporated.

Infection Control Link Nurse Program: An interdisciplinary approach n targeting health care-acquired infection

Science.gov (United States)

Sopirala, Madhuri M.; Yahle-Dunbar, Lisa; Smyer, Justin; Wellington, Linda; Dickman, Jeanne; Zikri, Nancy; Martin, Jennifer; Kulich, Pat; Taylor, David; Mekhjian, Hagop; Nash, Mary; Mansfield, Jerry; Pancholi, Preeti; Howard, Mary; Chase, Linda; Brown, Susan; Kipp, Kristopher; Lefeld, Kristen; Myers, Amber; Pan, Xueliang; Mangino, Julie E.

2014-01-01

Background We describe a successful interdisciplinary liaison program that effectively reduced health care-acquired (HCA), methicillin-resistant Staphylococcus aureus (MRSA) in a university hospital setting. Methods Baseline was from January 2006 to March 2008, and intervention period was April 2008 to September 2009. Staff nurses were trained to be liaisons (link nurses) to infection prevention (IP) personnel with clearly defined goals assigned and with ongoing monthly education. HCA-MRSA incidence per 1,000 patient-days (PD) was compared between baseline and intervention period along with total and non-HCA-MRSA, HCA and non-HCA-MRSA bacteremia, and hand soap/sanitizer usage. Hand hygiene compliance was assessed. Results A reduction in MRSA rates was as follows in intervention period compared with baseline: HCA-MRSA decreased by 28% from 0.92 to 0.67 cases per 1,000 PD (incidence rate ratio, 0.72; 95% confidence interval: 0.62–0.83, P Hand soap/sanitizer usage and compliance with hand hygiene also increased significantly during IP. Conclusion Link nurse program effectively reduced HCA-MRSA. Goal-defined metrics with ongoing reeducation for the nurses by IP personnel helped drive these results. PMID:24548456

Monitoring of Land-Surface Deformation in the Karamay Oilfield, Xinjiang, China, Using SAR Interferometry

Directory of Open Access Journals (Sweden)

Yusupujiang Aimaiti

2017-07-01

Full Text Available Synthetic Aperture Radar (SAR interferometry is a technique that provides high-resolution measurements of the ground displacement associated with various geophysical processes. To investigate the land-surface deformation in Karamay, a typical oil-producing city in the Xinjiang Uyghur Autonomous Region, China, Advanced Land Observing Satellite (ALOS Phased Array L-band Synthetic Aperture Radar (PALSAR data were acquired for the period from 2007 to 2009, and a two-pass differential SAR interferometry (D-InSAR process was applied. The experimental results showed that two sites in the north-eastern part of the city exhibit a clear indication of land deformation. For a further evaluation of the D-InSAR result, the Persistent Scatterer (PS and Small Baseline Subset (SBAS-InSAR techniques were applied for 21 time series Environmental Satellite (ENVISAT C-band Advanced Synthetic Aperture Radar (ASAR data from 2003 to 2010. The comparison between the D-InSAR and SBAS-InSAR measurements had better agreement than that from the PS-InSAR measurement. The maximum deformation rate attributed to subsurface water injection for the period from 2003 to 2010 was up to approximately 33 mm/year in the line of sight (LOS direction. The interferometric phase change from November 2007 to June 2010 showed a clear deformation pattern, and the rebound center has been expanding in scale and increasing in quantity.

Plastic deformation

NARCIS (Netherlands)

Sitter, de L.U.

1937-01-01

§ 1. Plastic deformation of solid matter under high confining pressures has been insufficiently studied. Jeffreys 1) devotes a few paragraphs to deformation of solid matter as a preface to his chapter on the isostasy problem. He distinguishes two properties of solid matter with regard to its

Curiosity's Mars Hand Lens Imager (MAHLI): Inital Observations and Activities

Science.gov (United States)

Edgett, K. S.; Yingst, R. A.; Minitti, M. E.; Robinson, M. L.; Kennedy, M. R.; Lipkaman, L. J.; Jensen, E. H.; Anderson, R. C.; Bean, K. M.; Beegle, L. W.;

Contribution of Deformation to Sea Ice Mass Balance: A Case Study From an N-ICE2015 Storm

Science.gov (United States)

Itkin, Polona; Spreen, Gunnar; Hvidegaard, Sine Munk; Skourup, Henriette; Wilkinson, Jeremy; Gerland, Sebastian; Granskog, Mats A.

2018-01-01

The fastest and most efficient process of gaining sea ice volume is through the mechanical redistribution of mass as a consequence of deformation events. During the ice growth season divergent motion produces leads where new ice grows thermodynamically, while convergent motion fractures the ice and either piles the resultant ice blocks into ridges or rafts one floe under the other. Here we present an exceptionally detailed airborne data set from a 9 km2 area of first year and second year ice in the Transpolar Drift north of Svalbard that allowed us to estimate the redistribution of mass from an observed deformation event. To achieve this level of detail we analyzed changes in sea ice freeboard acquired from two airborne laser scanner surveys just before and right after a deformation event brought on by a passing low-pressure system. A linear regression model based on divergence during this storm can explain 64% of freeboard variability. Over the survey region we estimated that about 1.3% of level sea ice volume was pressed together into deformed ice and the new ice formed in leads in a week after the deformation event would increase the sea ice volume by 0.5%. As the region is impacted by about 15 storms each winter, a simple linear extrapolation would result in about 7% volume increase and 20% deformed ice fraction at the end of the season.

Systemic mistakes in hand hygiene practice in Ukraine: detection, consequences and ways of elimination

Science.gov (United States)

Klymenko, Iryna; Kampf, Günter

2015-01-01

Aim: Every year, millions of people around the world suffer from different infectious diseases, considerable part of which are hospital-acquired infections. WHO considers hand hygiene as a priority measure aimed to reduce the level of infection. We evaluated various aspects related to the situational behavior and prioritization regarding hand hygiene measures among the healthcare workers of Ukraine. Method: Identification of system mistakes in hand hygiene was carried out first of all by direct and indirect observation of the activities of medical and pharmaceutical personnel in their everyday practice as well as during their participation in trainings on routine hand hygiene. Questionnaires also were used to estimate the level of hand hygiene compliance of participants of the study. During this period 112 training courses, 315 master-classes and presentations on proper hand hygiene were realized. The target audience included health care workers of medical centers, clinics, maternity hospitals, health care organizations and staff of pharmacies and pharmaceutical manufacturing enterprises in all regions of Ukraine. 638 respondents took part in anonymous survey on hand hygiene practice. Results: The most common mistakes were to regard hand washing and hand disinfection equally, to wash hands before doing a hand disinfection, to neglect the five moments for hand hygiene and to ignore hand hygiene before and after wearing protective gloves. Practitioners, medical attendants, pharmacy and pharmaceutical industry workers highlighted the need for practical and understandable instructions of various hand hygiene procedures, including the clarification of the possible technical mistakes. This became a ground for us to create individual master classes on hand hygiene for each cluster of healthcare workers. Conclusions: Changing hand hygiene behavior and attitude is possible by beginning to observe clinical practice and by involving healthcare workers in teaching and training

Deformation compensation in dynamic tomography; Compensation de deformations en tomographie dynamique

Energy Technology Data Exchange (ETDEWEB)

Desbat, L. [Universite Joseph Fourier, UMR CNRS 5525, 38 - Grenoble (France); Roux, S. [Universite Joseph Fourier, TIMC-IMAG, In3S, Faculte de Medecine, 38 - Grenoble (France)]|[CEA Grenoble, Lab. d' Electronique et de Technologie de l' Informatique (LETI), 38 (France); Grangeat, P. [CEA Grenoble, Lab. d' Electronique et de Technologie de l' Informatique (LETI), 38 (France)

2005-07-01

This work is a contribution to the compensation of motion in tomography. New classes of deformation are proposed, that compensates analytically by an algorithm of a F.B.P. type reconstruction. This work makes a generalisation of the known results for affine deformations, in parallel geometry and fan-beam, to deformation classes of infinite dimension able to include strong non linearities. (N.C.)

Deformation mechanisms of silicon during nanoscratching

Energy Technology Data Exchange (ETDEWEB)

Gassilloud, R.; Gasser, P.; Buerki, G.; Michler, J. [EMPA, Materials Science and Technology, Feuerwerkerstrasse 39, 3602 Thun (Switzerland); Ballif, C. [University of Neuchatel, A.-L. Breguet 2, 2000 Neuchatel (Switzerland)

2005-12-01

The deformation mechanisms of silicon {l_brace}001{r_brace} surfaces during nanoscratching were found to depend strongly on the loading conditions. Nanoscratches with increasing load were performed at 2 {mu}m/s (low velocity) and 100 {mu}m/s (high velocity). The load-penetration-distance curves acquired during the scratching process at low velocity suggests that two deformation regimes can be defined, an elasto-plastic regime at low loads and a fully plastic regime at high loads. High resolution scanning electron microscopy of the damaged location shows that the residual scratch morphologies are strongly influenced by the scratch velocity and the applied load. Micro-Raman spectroscopy shows that after pressure release, the deformed volume inside the nanoscratch is mainly composed of amorphous silicon and Si-XII at low scratch speeds and of amorphous silicon at high speeds. Transmission electron microscopy shows that Si nanocrystals are embedded in an amorphous matrix at low speeds, whereas at high speeds the transformed zone is completely amorphous. Furthermore, the extend of the transformed zone is almost independent of the scratching speed and is delimited by a dislocation rich area that extends about as deep as the contact radius into the surface. To explain the observed phase and defect distribution a contact mechanics based decompression model that takes into account the load, the velocity, the materials properties and the contact radius in scratching is proposed. It shows that the decompression rate is higher at low penetration depth, which is consistent with the observation of amorphous silicon in this case. The stress field under the tip is computed using an elastic contact mechanics model based on Hertz's theory. The model explains the observed shape of the transformed zone and suggests that during load increase, phase transformation takes place prior to dislocation nucleation. (copyright 2005 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Anti-bacterial efficacy of alcoholic hand rubs in the Kenyan market, 2015

Directory of Open Access Journals (Sweden)

Missiani Ochwoto

2017-01-01

Full Text Available Abstract Background Hand hygiene is known to be effective in preventing hospital and community-acquired infections. The increasing number of hand sanitizer brands in Kenyan hospitals and consumer outlets is of concern. Thus the main aim of this study was to evaluate the anti-bacterial efficacy and organoleptic properties of these hand sanitizers in Kenya. Methods This was an experimental, laboratory-based study of 14 different brands of hand sanitizers (coded HS1-14 available in various retail outlets and hospitals in Kenya. Efficacy was evaluated using standard non-pathogenic Escherichia coli (ATCC 25922, Staphylococcus aureus (ATCC 25923 and Pseudomonas aeruginosa (ATCC 27853 as per the European Standard (EN. The logarithmic reduction factors (RF were assessed at baseline and after treatment, and log reduction then calculated. Ten and 25 healthy volunteers participated in the efficacy and organoleptic studies respectively. Results Four (28.6% hand sanitizers (HS12, HS9, HS13 and HS14 showed a 5.9 reduction factor on all the three bacteria strains. Seven (50% hand sanitizers had efficacies of <3 against all the three bacteria strains used. Efficacy on E. Coli was higher compared to the other pathogens. Three hand sanitizers were efficacious on one of the pathogens and not the other. In terms of organoleptic properties, gel-based formulations were rated far higher than the liquid based formulations brands. Conclusion Fifty percent (50% of the selected hand sanitizers in the Kenyan market have efficacy that falls below the World Health Organization (WHO and DIN EN 1500:2013. Of the 14 hand sanitizers found in the Kenyan market, only four showed efficacies that were comparable to the WHO-formulation. There is a need to evaluate how many of these products with <3 efficacy that have been incorporated into the health system for hand hygiene and the country’s policy on regulations on their usage.

ESTIMATION OF PHASE DELAY DUE TO PRECIPITABLE WATER FOR DINSARBASED LAND DEFORMATION MONITORING

Directory of Open Access Journals (Sweden)

J. Susaki

2017-09-01

Full Text Available In this paper, we present a method for using the estimated precipitable water (PW to mitigate atmospheric phase delay in order to improve the accuracy of land-deformation assessment with differential interferometric synthetic aperture radar (DInSAR. The phase difference obtained from multi-temporal synthetic aperture radar images contains errors of several types, and the atmospheric phase delay can be an obstacle to estimating surface subsidence. In this study, we calculate PW from external meteorological data. Firstly, we interpolate the data with regard to their spatial and temporal resolutions. Then, assuming a range direction between a target pixel and the sensor, we derive the cumulative amount of differential PW at the height of the slant range vector at pixels along that direction. The atmospheric phase delay of each interferogram is acquired by taking a residual after a preliminary determination of the linear deformation velocity and digital elevation model (DEM error, and by applying high-pass temporal and low-pass spatial filters. Next, we estimate a regression model that connects the cumulative amount of PW and the atmospheric phase delay. Finally, we subtract the contribution of the atmospheric phase delay from the phase difference of the interferogram, and determine the linear deformation velocity and DEM error. The experimental results show a consistent relationship between the cumulative amount of differential PW and the atmospheric phase delay. An improvement in land-deformation accuracy is observed at a point at which the deformation is relatively large. Although further investigation is necessary, we conclude at this stage that the proposed approach has the potential to improve the accuracy of the DInSAR technique.

Monitoring Deformation in Graphene Through Hyperspectral Synchrotron Spectroscopy to Inform Fabrication

Energy Technology Data Exchange (ETDEWEB)

Winter, Allen Douglas [School; Rojas, Wudmir Y. [School; Williams, Adrienne D. [Materials; Kim, Steve S. [Materials; Ouchen, Fahima [Materials; Fischer, Daniel A. [National Institute of Standards and Technology, Gaithersburg, Maryland 20899, United States; Weiland, Conan [Synchrotron Research Inc., Melbourne, Florida 32901, United States; Principe, Edward [Synchrotron Research Inc., Melbourne, Florida 32901, United States; Banerjee, Sarbajit [Department; amp,M University, College Station, Texas 77840, United States; Huynh, Chuong [Carl Zeiss Microscopy, LLC, One Corporation Way, Peabody, Massachusetts 01960, United States; Naik, Rajesh R. [Materials; Liu, Yijin [Stanford; Mehta, Apurva [Stanford; Grote, James [Materials; Prendergast, David [Molecular; Campo, Eva M. [School; Department

2017-07-13

The promise from graphene to produce devices with high mobilities and detectors with fast response times is truncated in practice by strain and deformation originating during growth and subsequent processing. This work describes effects from graphene growth, multiple layer transfer, and substrate termination on out of plane deformation, critical to device performance. Synchrotron spectroscopy data was acquired with a state-of-the-art hyperspectral large-area detector to describe growth and processing with molecular sensitivity at wafer length scales. A study of methodologies used in data analysis discouraged dichroic ratio approaches in favor of orbital vector approximations and data mining algorithms. Orbital vector methods provide a physical insight into mobility-detrimental rippling by identifying ripple frequency as main actor, rather than intensity; which was confirmed by data mining algorithms, and in good agreement with electron scattering theories of corrugation in graphene. This work paves the way to efficient information from mechanical properties in graphene in a high throughput mode throughout growth and processing in a materials by design approach.

Automated local line rolling forming and simplified deformation simulation method for complex curvature plate of ships

Directory of Open Access Journals (Sweden)

Y. Zhao

2017-06-01

Full Text Available Local line rolling forming is a common forming approach for the complex curvature plate of ships. However, the processing mode based on artificial experience is still applied at present, because it is difficult to integrally determine relational data for the forming shape, processing path, and process parameters used to drive automation equipment. Numerical simulation is currently the major approach for generating such complex relational data. Therefore, a highly precise and effective numerical computation method becomes crucial in the development of the automated local line rolling forming system for producing complex curvature plates used in ships. In this study, a three-dimensional elastoplastic finite element method was first employed to perform numerical computations for local line rolling forming, and the corresponding deformation and strain distribution features were acquired. In addition, according to the characteristics of strain distributions, a simplified deformation simulation method, based on the deformation obtained by applying strain was presented. Compared to the results of the three-dimensional elastoplastic finite element method, this simplified deformation simulation method was verified to provide high computational accuracy, and this could result in a substantial reduction in calculation time. Thus, the application of the simplified deformation simulation method was further explored in the case of multiple rolling loading paths. Moreover, it was also utilized to calculate the local line rolling forming for the typical complex curvature plate of ships. Research findings indicated that the simplified deformation simulation method was an effective tool for rapidly obtaining relationships between the forming shape, processing path, and process parameters.

EthoHand: A dexterous robotic hand with ball-joint thumb enables complex in-hand object manipulation

OpenAIRE

Konnaris, C; Gavriel, C; Thomik, AAC; Aldo Faisal, A

2016-01-01

Our dexterous hand is a fundmanetal human feature that distinguishes us from other animals by enabling us to go beyond grasping to support sophisticated in-hand object manipulation. Our aim was the design of a dexterous anthropomorphic robotic hand that matches the human hand's 24 degrees of freedom, under-actuated by seven motors. With the ability to replicate human hand movements in a naturalistic manner including in-hand object manipulation. Therefore, we focused on the development of a no...

Hand-related physical function in rheumatic hand conditions

DEFF Research Database (Denmark)

Klokker, Louise; Terwee, Caroline B; Wæhrens, Eva Ejlersen

2016-01-01

as well as those items from the Patient Reported Outcomes Measurement Information System (PROMIS) Physical Function (PF) item bank that are relevant to patients with rheumatic hand conditions. Selection will be based on consensus among reviewers. Content validity of selected items will be established......INTRODUCTION: There is no consensus about what constitutes the most appropriate patient-reported outcome measurement (PROM) instrument for measuring physical function in patients with rheumatic hand conditions. Existing instruments lack psychometric testing and vary in feasibility...... and their psychometric qualities. We aim to develop a PROM instrument to assess hand-related physical function in rheumatic hand conditions. METHODS AND ANALYSIS: We will perform a systematic search to identify existing PROMs to rheumatic hand conditions, and select items relevant for hand-related physical function...

Hand-related physical function in rheumatic hand conditions

DEFF Research Database (Denmark)

Klokker, Louise; Terwee, Caroline; Wæhrens, Eva Elisabet Ejlersen

2016-01-01

INTRODUCTION: There is no consensus about what constitutes the most appropriate patient-reported outcome measurement (PROM) instrument for measuring physical function in patients with rheumatic hand conditions. Existing instruments lack psychometric testing and vary in feasibility...... and their psychometric qualities. We aim to develop a PROM instrument to assess hand-related physical function in rheumatic hand conditions. METHODS AND ANALYSIS: We will perform a systematic search to identify existing PROMs to rheumatic hand conditions, and select items relevant for hand-related physical function...... as well as those items from the Patient Reported Outcomes Measurement Information System (PROMIS) Physical Function (PF) item bank that are relevant to patients with rheumatic hand conditions. Selection will be based on consensus among reviewers. Content validity of selected items will be established...

Fluid flow simulation and permeability computation in deformed porous carbonate grainstones

Science.gov (United States)

Zambrano, Miller; Tondi, Emanuele; Mancini, Lucia; Lanzafame, Gabriele; Trias, F. Xavier; Arzilli, Fabio; Materazzi, Marco; Torrieri, Stefano

2018-05-01

In deformed porous carbonates, the architecture of the pore network may be modified by deformation or diagenetic processes altering the permeability with respect to the pristine rock. The effects of the pore texture and morphology on permeability in porous rocks have been widely investigated due to the importance during the evaluation of geofluid reservoirs. In this study, these effects are assessed by combining synchrotron X-ray computed microtomography (SR micro-CT) and computational fluid dynamics. The studied samples pertain to deformed porous carbonate grainstones highly affected by deformation bands (DBs) exposed in Northwestern Sicily and Abruzzo regions, Italy. The high-resolution SR micro-CT images of the samples, acquired at the SYRMEP beamline of the Elettra - Sincrotrone Trieste laboratory (Italy), were used for simulating a pressure-driven flow by using the lattice-Boltzmann method (LBM). For the experiments, a multiple relaxation time (MRT) model with the D3Q19 scheme was used to avoid viscosity-dependent results of permeability. The permeability was calculated using Darcy's law once steady conditions were reached. After the simulations, the pore-network properties (effective porosity, specific surface area, and geometrical tortuosity) were calculated using 3D images of the velocity fields. These images were segmented considering a velocity threshold value higher than zero. The study showed that DBs may generate significant heterogeneity and anisotropy of the permeability of the evaluated rock samples. Cataclasis and cementation process taking place within the DBs reduce the effective porosity and therefore the permeability. Contrary to this, pressure dissolution and faulting may generate connected channels which contribute to the permeability only parallel to the DB.

Channeling potential in single-walled carbon nanotubes: The effect of radial deformation

International Nuclear Information System (INIS)

Abu-Assy, M.K.; Soliman, M.S.

2016-01-01

We study the effect of radial deformation in single-walled carbon nanotubes (SWCNTs), due to one external factor, on the channeling potential. The calculations covered the channeling potential for positrons of 100 MeV move along the z-axis, which is the axis of the radially deformed SWCNTs (6, 0), (8, 0) under external mechanical stress at different values for the induced strain and also for radially deformed SWCNT (5, 5) under external transverse electric field of 1.8 and 2.6 V/Å. The calculations executed according to the continuum model approximation given by Lindhard for the case of an axial channeling in single crystals. The results of the calculations in this work agreed well with previous calculations depending on the equilibrium electron density in perfect carbon nanotubes. It has been found that, for perfect nanotubes, the channeling potential, i.e., the potential at any point (x, y) in a plane normal to the nanotube axis (xy-plane), is a function of the distance from the nanotube center whatever the (x, y) coordinate and hence, it could be expressed in terms of one independent variable. On the other hand, in radially deformed SWCNTs, the channeling potential was found to be a function of two independent variables (x, y) and could be given here by a general formula in terms of fitting parameters for each nanotube with chiral index (n, m). The obtained formula has been used in plotting the contour plot for the channeling potential.

Channeling potential in single-walled carbon nanotubes: The effect of radial deformation

Energy Technology Data Exchange (ETDEWEB)

Abu-Assy, M.K. [Physics Department, Faculty of Science, Suez-Canal University, Ismailia 41522 (Egypt); Soliman, M.S., E-mail: Mahmoud_einstien2@yahoo.com [Physics Department, Faculty of Science, Suez-Canal University, El-Arish (Egypt)

2016-10-01

We study the effect of radial deformation in single-walled carbon nanotubes (SWCNTs), due to one external factor, on the channeling potential. The calculations covered the channeling potential for positrons of 100 MeV move along the z-axis, which is the axis of the radially deformed SWCNTs (6, 0), (8, 0) under external mechanical stress at different values for the induced strain and also for radially deformed SWCNT (5, 5) under external transverse electric field of 1.8 and 2.6 V/Å. The calculations executed according to the continuum model approximation given by Lindhard for the case of an axial channeling in single crystals. The results of the calculations in this work agreed well with previous calculations depending on the equilibrium electron density in perfect carbon nanotubes. It has been found that, for perfect nanotubes, the channeling potential, i.e., the potential at any point (x, y) in a plane normal to the nanotube axis (xy-plane), is a function of the distance from the nanotube center whatever the (x, y) coordinate and hence, it could be expressed in terms of one independent variable. On the other hand, in radially deformed SWCNTs, the channeling potential was found to be a function of two independent variables (x, y) and could be given here by a general formula in terms of fitting parameters for each nanotube with chiral index (n, m). The obtained formula has been used in plotting the contour plot for the channeling potential.

q-Deformed KP Hierarchy and q-Deformed Constrained KP Hierarchy

OpenAIRE

He, Jingsong; Li, Yinghua; Cheng, Yi

2006-01-01

Using the determinant representation of gauge transformation operator, we have shown that the general form of $au$ function of the $q$-KP hierarchy is a $q$-deformed generalized Wronskian, which includes the $q$-deformed Wronskian as a special case. On the basis of these, we study the $q$-deformed constrained KP ($q$-cKP) hierarchy, i.e. $l$-constraints of $q$-KP hierarchy. Similar to the ordinary constrained KP (cKP) hierarchy, a large class of solutions of $q$-cKP hierarchy can be represent...

Hand-eye calibration using a target registration error model.

Science.gov (United States)

Chen, Elvis C S; Morgan, Isabella; Jayarathne, Uditha; Ma, Burton; Peters, Terry M

2017-10-01

Surgical cameras are prevalent in modern operating theatres and are often used as a surrogate for direct vision. Visualisation techniques (e.g. image fusion) made possible by tracking the camera require accurate hand-eye calibration between the camera and the tracking system. The authors introduce the concept of 'guided hand-eye calibration', where calibration measurements are facilitated by a target registration error (TRE) model. They formulate hand-eye calibration as a registration problem between homologous point-line pairs. For each measurement, the position of a monochromatic ball-tip stylus (a point) and its projection onto the image (a line) is recorded, and the TRE of the resulting calibration is predicted using a TRE model. The TRE model is then used to guide the placement of the calibration tool, so that the subsequent measurement minimises the predicted TRE. Assessing TRE after each measurement produces accurate calibration using a minimal number of measurements. As a proof of principle, they evaluated guided calibration using a webcam and an endoscopic camera. Their endoscopic camera results suggest that millimetre TRE is achievable when at least 15 measurements are acquired with the tracker sensor ∼80 cm away on the laparoscope handle for a target ∼20 cm away from the camera.

Learning-by-Being-Acquired

DEFF Research Database (Denmark)

Colombo, Massimo Gaetano; Moreira, Solon; Rabbiosi, Larissa

2016-01-01

In horizontal acquisitions, the post-acquisition integration of the R&D function often damages the inventive labor force and results in lower innovative productivity of acquired inventors. In this paper we study post-acquisition integration in terms of R&D team reorganization-i.e., the creation...... of new teams with both inventors of the acquiring and acquired firms-and assess the impact of this integration action in the period that immediately follows the acquisition. Drawing on social identity and self-categorization theories, we argue that R&D team reorganization increases the acquired inventors...

A Least Square Approach for Joining Persistent Scatterer InSAR Time Series Acquired by Different Satellites

Science.gov (United States)

Caro Cuenca, Miguel; Esfahany, Sami Samiei; Hanssen, Ramon F.

2010-12-01

Persistent scatterer Radar Interferometry (PSI) can provide with a wealth of information on surface motion. These methods overcome the major limitations of the antecessor technique, interferometric SAR (InSAR), such as atmospheric disturbances, by detecting the scatterers which are slightly affected by noise. The time span that surface deformation processes are observed is limited by the satellite lifetime, which is usually less than 10 years. However most of deformation phenomena last longer. In order to fully monitor and comprehend the observed signal, acquisitions from different sensors can be merged. This is a complex task for one main reason. PSI methods provide with estimations that are relative in time to one of the acquisitions which is referred to as master or reference image. Therefore, time series acquired by different sensors will have different reference images and cannot be directly compared or joint unless they are set to the same time reference system. In global terms, the operation of translating from one to another reference systems consist of calculating a vertical offset, which is the total deformation that occurs between the two master times. To estimate this offset, different strategies can be applied, for example, using additional data such as leveling or GPS measurements. In this contribution we propose to use a least squares to merge PSI time series without any ancillary information. This method treats the time series individually, i.e. per PS, and requires some knowledge of the deformation signal, for example, if a polynomial would fairly describe the expected behavior. To test the proposed approach, we applied it to the southern Netherlands, where the surface is affected by ground water processes in abandoned mines. The time series were obtained after processing images provided by ERS1/2 and Envisat. The results were validated using in-situ water measurements, which show very high correlation with deformation time series.

Deformation analysis of a film-overlapped micro-pump membrane structure

International Nuclear Information System (INIS)

Lee, Fu-Shin; Wang, Pi-Wen; Chen, Chih-Hsiung

2008-01-01

A novel approach is developed to study a film-overlapped membrane structure. Meanwhile, the established model is employed to design the micro-pump membrane structure and to evaluate its pumping efficiency. Two-dimensional coupling effects between the overlapping actuator films and the deformable membrane are thoroughly investigated, including the influences on the membrane from the overlapping films' elongation effects, Poisson's ratio effects and shear strain effects. Overall deformations and interactions for the three-layer membrane structures are accurately calculated through exercising the developed model, in contrast to what difficulties are usually encountered in carrying out FEM methods with very thin elements meshed for the actuator films. Furthermore, this study demonstrates that the high stiffness of the actuating metal films needs to be reflected in the equivalent stiffness of the membrane structures, especially when the sizes of the actuator films become compatible with the sizes of the membranes. Hence, the optimal micro-pumping efficiency of a membrane structure is acquired upon exercising the developed model, and larger sizes of the actuating films do not definitely obtain larger pumping efficiencies for the electromagnetically actuated micro-pumps

Monitoring Volcano Deformation in the Northernmost Andes with ALOS InSAR Time-Series

Science.gov (United States)

Morales Rivera, A. M.; Amelung, F.

2014-12-01

Satellite-based Interferometric Synthetic Aperture Radar (InSAR) is well known to be used as a volcano monitoring tool, providing the opportunity to conduct local and regional surveys to detect and measure volcanic deformation. The signals detected by InSAR on volcanoes can be related to various phenomena, such as volume changes in magmatic reservoirs, compaction of recent deposits, changes in hydrothermal activity, and flank instability. The InSAR time-series method has well documented examples of these phenomena, including precursory inflation of magma reservoirs months prior to volcanic eruptions, proving its potential for early warning systems. We use the ALOS-1 satellite from the Japanese Aerospace Exploration Agency (JAXA), which acquired a global L-band data set of nearly 20 acquisitions during 2007-2011, to make an InSAR time-series analysis using the Small Baseline method (SBAS). Our analysis covers all of the volcanoes in Colombia, Ecuador, and Peru that are cataloged by the Global Volcanism Program. We present results showing time-dependent ground deformation on an near the volcanoes, and present kinematic models to constrain the characteristics of the magmatic sources for the cases in which the deformation is likely related to changes in magma reservoir pressurization.

Time-Dependent Crustal Deformation Associated With the 2004 Chuetsu and the 2007 Chuetsu-Oki Earthquakes

Science.gov (United States)

Meneses Gutierrez, A.; Sagiya, T.

2013-12-01

There is an ongoing concentrated deformation along the Japan Sea coast, which has been identified as Niigata Kobe Tectonic Zone (Sagiya et al., 2000). Large historical earthquakes have occurred in this area, and in recent years, Niigata has suffered the impact of two important events, known as the 2004 Mid-Niigata Prefecture earthquake (M 6.8) and The 2007 Niigata-ken Chuetsu-Oki earthquake (M 6.6), which considerately affected the crustal deformation pattern. For this reason, we review temporal variation of crustal deformation pattern in the mid Niigata region based on daily coordinates of 28 GPS sites from the GEONET network for three time windows: before 2004, 2004-2007 and after 2007 until March 2011, to avoid effects of crustal deformation associated with the 2011 Tohoku-Oki earthquake. We observed a migration of the deformation pattern in the East-West direction through the contraction belts for the above time windows. Before 2004, we recognize a clear shortening of 0.3ppm/yr in the area between the source regions of 2004 and 2007 quakes. After the 2004 Chuetsu earthquake, this shortening rate decreased. On the other hand, an accelerated contraction occurred to the east of this region, around the source region of the 2004 earthquake. After the 2007 earthquake, another contraction zone appeared to the northwest, near the 2007 source region. These time-dependent behaviors suggest there exists strong interaction between parallel fault segments in this area. It is crucially important to reveal such interaction to understand crustal deformation and seismogenesis in this region. We construct kinematic deformation models to interpret the time-dependent deformation pattern for each time period and to investigate mechanical interaction of coseismic as well as probably aseismic fault slips. Optimal faults parameters were established using a grid search, and computing the 95% confidence interval for each model parameter using the normalized Chi-squared distribution to

A Study to Assess Knowledge and Attitude Regarding Hand Hygiene amongst Residents and Nursing Staff in a Tertiary Health Care Setting of Bhopal City

OpenAIRE

Maheshwari, Veena; kaore, Navin Chandra M; Ramnani, Vijay Kumar; Gupta, Sanjay Kumar; Borle, Amod; Kaushal, Rituja

2014-01-01

Background: Infection due to hospital-acquired microbes is an evolving problem worldwide, and horizontal transmission of bacterial organism continues to cause a high nosocomial infection rate in health care settings. Most nosocomial infections are thought to be transmitted by the hands of health care workers.The application of hand hygiene is effective in reducing infection rates.

High-carbon chromium steel resistance to small plastic deformation

International Nuclear Information System (INIS)

Gajduchenya, V.F.; Madyanov, S.A.; Apaev, B.A.; Kirillov, Yu.V.; Sokolov, L.D.

1978-01-01

The phase composition of a steel with 1.08% C and 2.1% Cr, and the variation in the level of microstresses in the matrix as related to the annealing temperature in the range of 400-600 deg C and in the applied compression stress were investigated. To study the phase composition, and chromium content in the α-solution and the carbide phases, magnetic, chemical, and X-ray spectrum analyses were carried out. The change in the level of microstresses was determined roentgenographically. During the stress relaxation test at temperatures of 20-180 deg C, the mechanism of plastic deformation near the yield point was investigated. It is shown that three dislocation mechanisms operate in high-carbon chromium steel under the conditions at hand: overcoming the Pierls-Nabarro barriers by the dislocations, overcoming the stress fields of coherent carbide particles by dislocations, and circumvention of second-phase particles by dislocations. The dependence of the realization of the different plastic deformation mechanisms on the number of carbide particles and the chromium concentration in the matrix was established. The thermally activated nature of the motion of the dislocations under conditions of stress relaxation at an elevated temperature is noted

Hand Fractures

Science.gov (United States)

... All Topics A-Z Videos Infographics Symptom Picker Anatomy Bones Joints Muscles Nerves Vessels Tendons About Hand Surgery What is ... Hand Therapist? Media Find a Hand Surgeon Home Anatomy ... DESCRIPTION The bones of the hand serve as a framework. This framework supports the muscles that make the wrist and fingers move. When ...

Holocene Flexural Deformation over the Nile Delta: Evidence from Radar Interferometry

Science.gov (United States)

Gebremichael, E.; Sultan, M.; Becker, R.

2017-12-01

Isostatic adjustment and subsequent subsidence and uplift due to sediment and water loading and unloading mechanisms is one of the major factors that produce regional deformational patterns across river deltas. Using 84 Envisat ASAR scenes that were acquired (2004 - 2010) along three tracks and applying Persistent scatterer (PS) radar interferometric techniques, we documented flexural deformational patterns over the entire Nile Delta (length: 186 km; width: 240 km) of Egypt. The passive continental margin of Africa subsided from Jurassic time onwards due to isostatic loading creating an accommodation space and consequently, the deposition of relatively younger sediments on the oceanic crust. In river deltas, the flexural isostasy model dictates that a subsidence in the oceanic crust side should be balanced by a bulge (uplift) in the flanking regions. Using radar interferometry, we were able to identify the flexural deformation pattern and map its spatial extent over the northern and central Nile Delta region. Findings include: (1) the northern Nile Delta region (block) is separated from the southern delta region by an east-west trending, extensively faulted, hinge line that signifies the boundary between two deformational patterns (subsidence and uplift). It separates the highly subsiding (up to 9.8 mm/yr) northern delta block (up to 85 km long) from the nearly stable (0.4 mm/yr; averaged) southern delta block (up to 91 km long). The hinge line marks the end of the passive continental margin of Africa and the beginning of the oceanic crust of the Mediterranean. (2) We mapped the extent of a 20-40 km wide flexural uplift zone to the south of the hinge line. Within the flexural uplift zone (2.5 mm/yr; averaged), there is a gradual increase in uplift rate reaching peak value (up to 7 mm/yr) near the midpoint of the zone. (3) The uplift rate gradually decreases south of the flexure boundary reaching 0.3 mm/yr at the southern periphery of the delta. (4) The flexural

Fission gas induced deformation model for FRAP-T6 and NSRR irradiated fuel test simulations

Energy Technology Data Exchange (ETDEWEB)

Nakamura, Takehiko; Sasajima, Hideo; Fuketa, Toyoshi [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Hosoyamada, Ryuji; Mori, Yukihide

1996-11-01

Pulse irradiation tests of irradiated fuels under simulated reactivity initiated accidents (RIAs) have been carried out at the Nuclear Safety Research Reactor (NSRR). Larger cladding diameter increase was observed in the irradiated fuel tests than in the previous fresh fuel tests. A fission gas induced cladding deformation model was developed and installed in a fuel behavior analysis code, FRAP-T6. The irradiated fuel tests were analyzed with the model in combination with modified material properties and fuel cracking models. In Test JM-4, where the cladding temperature rose to higher temperatures and grain boundary separation by the pulse irradiation was significant, the fission gas model described the cladding deformation reasonably well. The fuel had relatively flat radial power distribution and the grain boundary gas from the whole radius was calculated to contribute to the deformation. On the other hand, the power density in the irradiated LWR fuel rods in the pulse irradiation tests was remarkably higher at the fuel periphery than the center. A fuel thermal expansion model, GAPCON, which took account of the effect of fuel cracking by the temperature profile, was found to reproduce well the LWR fuel behavior with the fission gas deformation model. This report present details of the models and their NSRR test simulations. (author)

Deformations of superconformal theories

Energy Technology Data Exchange (ETDEWEB)

Córdova, Clay [School of Natural Sciences, Institute for Advanced Study,1 Einstein Drive, Princeton, NJ 08540 (United States); Dumitrescu, Thomas T. [Department of Physics, Harvard University,17 Oxford Street, Cambridge, MA 02138 (United States); Intriligator, Kenneth [Department of Physics, University of California,9500 Gilman Drive, San Diego, La Jolla, CA 92093 (United States)

2016-11-22

We classify possible supersymmetry-preserving relevant, marginal, and irrelevant deformations of unitary superconformal theories in d≥3 dimensions. Our method only relies on symmetries and unitarity. Hence, the results are model independent and do not require a Lagrangian description. Two unifying themes emerge: first, many theories admit deformations that reside in multiplets together with conserved currents. Such deformations can lead to modifications of the supersymmetry algebra by central and non-central charges. Second, many theories with a sufficient amount of supersymmetry do not admit relevant or marginal deformations, and some admit neither. The classification is complicated by the fact that short superconformal multiplets display a rich variety of sporadic phenomena, including supersymmetric deformations that reside in the middle of a multiplet. We illustrate our results with examples in diverse dimensions. In particular, we explain how the classification of irrelevant supersymmetric deformations can be used to derive known and new constraints on moduli-space effective actions.

Acquired neuropathies.

Science.gov (United States)

Lozeron, Pierre; Trocello, Jean-Marc; Kubis, Nathalie

2013-09-01

Acquired neuropathies represent most of the neuropathies encountered in clinical practice. Hundreds of causes have been identified even though up to 41% of patients are still classified as idiopathic (Rajabally and Shah in J Neurol 258:1431-1436, 1). Routine evaluation relies on comprehensive medical history taking, clinical examination, nerve conduction studies and laboratory tests. Other investigations such as nerve biopsy or nerve or muscle imaging are performed in specific settings. This review focuses on recent advances in acquired neuropathies.

Ocean deformation processes at the Caribbean-North America-South America triple junction: Initial results of the 2007 ANTIPLAC marine survey

Science.gov (United States)

Benard, F.; Deville, E.; Le Drezen, E.; Loubrieu, B.; Maltese, L.; Patriat, M.; Roest, W.; Thereau, E.; Umber, M.; Vially, R.

2007-12-01

Marine geophysical data (multibeam and seismic lines) acquired in 2007 (ANTIPLAC survey) in the North-South Americas-Caribbean triple point (Central Atlantic, Barracuda and Tiburon ridges area), provide information about the structure, the tectonic processes and the timing of the deformation in this large diffuse zone of polyphase deformation. The deformation of the plate boundary between the north and south Americas is distributed on several structures located in the Atlantic plain, at the front of the Barbados accretionary prism. In this area of deformation of the Atlantic oceanic lithosphere, the main depressions and transform troughs are filled by Late Pliocene-Pleistocene turbidite sediments, especially in the Barracuda trough, north of Barracuda ridge. These sediments are not issued from the Lesser Antilles volcanic arc but they are sourced from the East, probably by the Orinoco turbidite distal system, through channels transiting in the Atlantic abyssal plain. These Late Pliocene- Quaternary sediments show locally spectacular evidences of syntectonic deformation. It can be shown notably that Barracuda ridge includes a pre-existing transform fault system which has been folded and uplifted very recently during Pleistocene times. This recent deformation has generate relieves up to 2 km high with associated erosion processes notably along the northern flank the Barracuda ridge. The subduction of these recently deformed ridges induces deformation of earlier structures within the Barbados accretionary prism. These asperities within the Atlantic oceanic lithosphere which is subducted in the Lesser Antilles active margin are correlated with the zone of intense seismic activity below the volcanic arc.

q-Deformed Kink solutions

International Nuclear Information System (INIS)

Lima, A.F. de

2003-01-01

The q-deformed kink of the λφ 4 -model is obtained via the normalisable ground state eigenfunction of a fluctuation operator associated with the q-deformed hyperbolic functions. The kink mass, the bosonic zero-mode and the q-deformed potential in 1+1 dimensions are found. (author)

Investigation of Stability of Precise Geodetic Instruments Used in Deformation Monitoring

Science.gov (United States)

Woźniak, Marek; Odziemczyk, Waldemar

2017-12-01

Monitoring systems using automated electronic total stations are an important element of safety control of many engineering objects. In order to ensure the appropriate credibility of acquired data, it is necessary that instruments (total stations in most of the cases) used for measurements meet requirements of measurement accuracy, as well as the stability of instrument axis system geometry. With regards to the above, it is expedient to conduct quality control of data acquired using electronic total stations in the context of performed measurement procedures. This paper presents results of research conducted at the Faculty of Geodesy and Cartography at Warsaw University of Technology investigating the stability of "basic" error values (collimation, zero location for V circle, inclination), for two types of automatic total stations: TDA 5005 and TCRP 1201+. Research provided also information concerning the influence of temperature changes upon the stability of investigated instrument's optical parameters. Results are presented in graphical analytic technique. Final conclusions propose methods, which allow avoiding negative results of measuring tool-set geometry changes during conducting precise deformation monitoring measurements.

Analysis of radiographic bone parameters throughout the surgical lengthening and deformity correction of extremities.

Science.gov (United States)

Atanasov, Nenad; Poposka, Anastasika; Samardziski, Milan; Kamnar, Viktor

2014-01-01

Radiographic examination of extremities in surgical lengthening and/or correction of deformities is of crucial importance for the assessment of new bone formation. The purpose of this study is to confirm the diagnostic value of radiography in precise detection of bone parameters in various lengthening or correction stages in patients treated by limb-lengthening and deformity correction. 50 patients were treated by the Ilizarov method of limb lengthening or deformity correction at the University Orthopaedic Surgery Clinic in Skopje, and analysed over the period from 2006 to 2012. The patients were divided into two groups. The first group consisted of 27 patients with limb-lengthening because of congenital shortening. The second group consisted of 23 patients treated for acquired limb deformities. The results in both groups were received in three stages of new bone formation and were based on the appearance of 3 radiographic parameters at the distraction/compression site. The differences between the presence of all radiographic bone parameters in different stages of new bone formation were statistically signficant in both groups, especially the presence of the cortical margin in the first group (Cochran Q=34.43, df=2, p=0.00000). The comparative analysis between the two groups showed a statistically significant difference in the presence of initial bone elements and cystic formations only in the first stage. Almost no statistical significance in the differences between both groups of patients with regard to 3 radiographic parameters in 3 stages of new bone formation, indicates a minor influence of the etiopathogenetic background on the new bone formation in patients treated by gradual lengthening or correction of limb deformities.

Time-series analysis of surface deformation at Brady Hot Springs geothermal field (Nevada) using interferometric synthetic aperture radar

Energy Technology Data Exchange (ETDEWEB)

Ali, S. T. [Univ. of Wisconsin, Madison, WI (United States); Akerley, J. [Ormat Technologies Inc., Reno, NV (United States); Baluyut, E. C. [Univ. of Wisconsin, Madison, WI (United States); Cardiff, M. [Univ. of Wisconsin, Madison, WI (United States); Davatzes, N. C. [Temple Univ., Philadelphia, PA (United States). Dept. of Earth and Environmental Science; Feigl, K. L. [Univ. of Wisconsin, Madison, WI (United States); Foxall, W. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Fratta, D. [Univ. of Wisconsin, Madison, WI (United States); Mellors, R. J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Spielman, P. [Ormat Technologies Inc., Reno, NV (United States); Wang, H. F. [Univ. of Wisconsin, Madison, WI (United States); Zemach, E. [Ormat Technologies Inc., Reno, NV (United States)

2016-05-01

We analyze interferometric synthetic aperture radar (InSAR) data acquired between 2004 and 2014, by the ERS-2, Envisat, ALOS and TerraSAR-X/TanDEM-X satellite missions to measure and characterize time-dependent deformation at the Brady Hot Springs geothermal field in western Nevada due to extraction of fluids. The long axis of the ~4 km by ~1.5 km elliptical subsiding area coincides with the strike of the dominant normal fault system at Brady. Within this bowl of subsidence, the interference pattern shows several smaller features with length scales of the order of ~1 km. This signature occurs consistently in all of the well-correlated interferometric pairs spanning several months. Results from inverse modeling suggest that the deformation is a result of volumetric contraction in shallow units, no deeper than 600 m, likely associated with damaged regions where fault segments mechanically interact. Such damaged zones are expected to extend downward along steeply dipping fault planes, providing a high permeability conduit to the production wells. Using time series analysis, we test the hypothesis that geothermal production drives the observed deformation. We find a good correlation between the observed deformation rate and the rate of production in the shallow wells. We also explore mechanisms that could potentially cause the observed deformation, including thermal contraction of rock, decline in pore pressure and dissolution of minerals over time.

Hand Matters: Left-Hand Gestures Enhance Metaphor Explanation

Science.gov (United States)

Argyriou, Paraskevi; Mohr, Christine; Kita, Sotaro

2017-01-01

Research suggests that speech-accompanying gestures influence cognitive processes, but it is not clear whether the gestural benefit is specific to the gesturing hand. Two experiments tested the "(right/left) hand-specificity" hypothesis for self-oriented functions of gestures: gestures with a particular hand enhance cognitive processes…

A hand hygiene intervention to decrease infections among children attending day care centers: Design of a cluster randomized controlled trial

NARCIS (Netherlands)

T.P. Zomer (Tizza); V. Erasmus (Vicky); N. Vlaar (Nico); E.F. van Beeck (Ed); A. Tjon-A-Tsien (Aimée); J.H. Richardus (Jan Hendrik); H.A.C.M. Voeten (Hélène)

2013-01-01

textabstractBackground: Day care center attendance has been recognized as a risk factor for acquiring gastrointestinal and respiratory infections, which can be prevented with adequate hand hygiene (HH). Based on previous studies on environmental and sociocognitive determinants of caregivers'

[Hand osteoarthritis].

Science.gov (United States)

Šenolt, Ladislav

Hand osteoarthritis (OA) is a common chronic disorder causing pain and limitation of mobility of affected joints. The prevalence of hand OA increases with age and more often affects females. Clinical signs obviously do not correlate with radiographic findings - symptomatic hand OA affects approximately 26 % of adult subjects, but radiographic changes can be found in up to two thirds of females and half of males older than 55 years.Disease course differ among individual patients. Hand OA is a heterogeneous disease. Nodal hand OA is the most common subtype affecting interphalangeal joints, thumb base OA affects first carpometacarpal joint. Erosive OA represents a specific subtype of hand OA, which is associated with joint inflammation, more pain, functional limitation and erosive findings on radiographs.Treatment of OA is limited. Analgesics and nonsteroidal anti-inflammatory drugs are the only agents reducing symptoms. New insights into the pathogenesis of disease should contribute to the development of novel effective treatment of hand OA.

Experimental deformation of a mafic rock - interplay between fracturing, reaction and viscous deformation

Science.gov (United States)

Marti, Sina; Stünitz, Holger; Heilbronner, Renée; Plümper, Oliver; Drury, Martyn

2016-04-01

Deformation experiments were performed on natural Maryland Diabase (˜ 55% Plg, 42% Px, 3% accessories, 0.18 wt.-% H2O added) in a Griggs-type deformation apparatus in order to explore the brittle-viscous transition and the interplay between deformation and mineral reactions. Shear experiments at strain rates of ˜ 2e-5 /s are performed, at T=600, 700 and 800°C and confining pressures Pc=1.0 and 1.5 GPa. Deformation localizes in all experiments. Below 700°C, the microstructure is dominated by brittle deformation with a foliation formed by cataclastic flow and high strain accommodated along 3-5 major ultracataclasite shear bands. At 700°C, the bulk of the material still exhibits abundant microfractures, however, deformation localizes into an anastomosing network of shear bands (SB) formed from a fine-grained (<< 1 μm) mixture of newly formed Plg and Amph. These reaction products occur almost exclusively along syn-kinematic structures such as fractures and SB. Experiments at 800°C show extensive mineral reactions, with the main reaction products Amph+Plg (+Zo). Deformation is localized in broad C' and C SB formed by a fine-grained (0.1 - 0.8 μm) mixture of Plg+Amph (+Zo). The onset of mineral reactions in the 700°C experiments shows that reaction kinetics and diffusional mass transport are fast enough to keep up with the short experimental timescales. While in the 700°C experiments brittle processes kinematically contribute to deformation, fracturing is largely absent at 800°C. Diffusive mass transfer dominates. The very small grain size within SB favours a grain size sensitive deformation mechanism. Due to the presence of water (and relatively high supported stresses), dissolution-precipitation creep is interpreted to be the dominant strain accommodating mechanism. From the change of Amph coronas around Px clasts with strain, we can determine that Amph is re-dissolved at high stress sites while growing in low stress sites, showing the ability of Amph to

Study of the active deformation of Mitidja (Tell Atlas, Algeria) by GPS

Science.gov (United States)

Bacha, Wahab; Masson, Frederic; Yelles-Chaouche, Abdelkrim; Lammali, Kamel; Bellik, Amar; Hamai, Lamine

2013-04-01

A network was created in the Mitidja region around the capital Algiers (Algeria). It has been established to study the deformation of the region and the slow operation of flaws in it. The network was installed by a distribution of GPS stations according to structural domains existing in the region. Twelve bases spread across the study area, have been installed. The measurements were acquired by performing four measurement campaigns in 2006, 2007, 2009 and 2010, with sessions over a month of action. This work allowed the installation of a geodetic network of regional monitoring by methodology GPS in the zone of Mitidja (Tellian Atlas, Algeria). Four observation campaigns were carried out on this area with session's superiors in one month of measurements. The treatment was carried out with software GAMIT-GLOBK, the network is attached to several world stations IGS treated between 2000-2010, indexed in a precise frame of reference ITRF05. The results presented in this memory show a deformation in shortening ≤ 0.5 mm/an in the plain of Mitidja and the surrounding Solid masses.

Deformation of second and third quantization

Science.gov (United States)

Faizal, Mir

2015-03-01

In this paper, we will deform the second and third quantized theories by deforming the canonical commutation relations in such a way that they become consistent with the generalized uncertainty principle. Thus, we will first deform the second quantized commutator and obtain a deformed version of the Wheeler-DeWitt equation. Then we will further deform the third quantized theory by deforming the third quantized canonical commutation relation. This way we will obtain a deformed version of the third quantized theory for the multiverse.

a New Approach for Subway Tunnel Deformation Monitoring: High-Resolution Terrestrial Laser Scanning

Science.gov (United States)

Li, J.; Wan, Y.; Gao, X.

2012-07-01

With the improvement of the accuracy and efficiency of laser scanning technology, high-resolution terrestrial laser scanning (TLS) technology can obtain high precise points-cloud and density distribution and can be applied to high-precision deformation monitoring of subway tunnels and high-speed railway bridges and other fields. In this paper, a new approach using a points-cloud segmentation method based on vectors of neighbor points and surface fitting method based on moving least squares was proposed and applied to subway tunnel deformation monitoring in Tianjin combined with a new high-resolution terrestrial laser scanner (Riegl VZ-400). There were three main procedures. Firstly, a points-cloud consisted of several scanning was registered by linearized iterative least squares approach to improve the accuracy of registration, and several control points were acquired by total stations (TS) and then adjusted. Secondly, the registered points-cloud was resampled and segmented based on vectors of neighbor points to select suitable points. Thirdly, the selected points were used to fit the subway tunnel surface with moving least squares algorithm. Then a series of parallel sections obtained from temporal series of fitting tunnel surfaces were compared to analysis the deformation. Finally, the results of the approach in z direction were compared with the fiber optical displacement sensor approach and the results in x, y directions were compared with TS respectively, and comparison results showed the accuracy errors of x, y, z directions were respectively about 1.5 mm, 2 mm, 1 mm. Therefore the new approach using high-resolution TLS can meet the demand of subway tunnel deformation monitoring.

Computed tomography in children with community-acquired pneumonia.

Science.gov (United States)

Andronikou, Savvas; Goussard, Pierre; Sorantin, Erich

2017-10-01

Diagnostic imaging plays a significant role in both the diagnosis and treatment of complications of pneumonia in children and chest radiography is the imaging modality of choice. Computed tomography (CT) on the other hand, is not currently a first-line imaging tool for children with suspected uncomplicated community-acquired pneumonia and is largely reserved for when complications of pneumonia are suspected or there is difficulty in differentiating pneumonia from other pathology. This review outlines the situations where CT needs to be considered in children with pneumonia, describes the imaging features of the parenchymal and pleural complications of pneumonia, discusses how CT may have a wider role in developing countries where human immunodeficiency virus (HIV) and tuberculosis are prevalent, makes note of the role of CT scanning for identifying missed foreign body aspiration and, lastly, addresses radiation concerns.

Computed tomography in children with community-acquired pneumonia

Energy Technology Data Exchange (ETDEWEB)

Andronikou, Savvas [Bristol Royal Hospital for Children and the University of Bristol, Department of Paediatric Radiology, Bristol (United Kingdom); University of Cape Town, Department of Radiology, Cape Town (South Africa); Goussard, Pierre [Tygerberg Hospital, Stellenbosch University, Department of Paediatrics and Child Health, Cape Town (South Africa); Sorantin, Erich [Medical University Graz, Department of Radiology, Graz (Austria)

2017-10-15

Diagnostic imaging plays a significant role in both the diagnosis and treatment of complications of pneumonia in children and chest radiography is the imaging modality of choice. Computed tomography (CT) on the other hand, is not currently a first-line imaging tool for children with suspected uncomplicated community-acquired pneumonia and is largely reserved for when complications of pneumonia are suspected or there is difficulty in differentiating pneumonia from other pathology. This review outlines the situations where CT needs to be considered in children with pneumonia, describes the imaging features of the parenchymal and pleural complications of pneumonia, discusses how CT may have a wider role in developing countries where human immunodeficiency virus (HIV) and tuberculosis are prevalent, makes note of the role of CT scanning for identifying missed foreign body aspiration and, lastly, addresses radiation concerns. (orig.)

Deformations of the Almheiri-Polchinski model

Energy Technology Data Exchange (ETDEWEB)

Kyono, Hideki; Okumura, Suguru; Yoshida, Kentaroh [Department of Physics, Kyoto University, Kitashirakawa Oiwake-cho, Kyoto 606-8502 (Japan)

2017-03-31

We study deformations of the Almheiri-Polchinski (AP) model by employing the Yang-Baxter deformation technique. The general deformed AdS{sub 2} metric becomes a solution of a deformed AP model. In particular, the dilaton potential is deformed from a simple quadratic form to a hyperbolic function-type potential similarly to integrable deformations. A specific solution is a deformed black hole solution. Because the deformation makes the spacetime structure around the boundary change drastically and a new naked singularity appears, the holographic interpretation is far from trivial. The Hawking temperature is the same as the undeformed case but the Bekenstein-Hawking entropy is modified due to the deformation. This entropy can also be reproduced by evaluating the renormalized stress tensor with an appropriate counter-term on the regularized screen close to the singularity.

Internal deformation in layered Zechstein-III K-Mg salts. Structures formed by complex deformation and high contrasts in viscosity observed in drill cores.

Science.gov (United States)

Raith, Alexander; Urai, Janos L.

2016-04-01

During the evaporation of a massive salt body, alternations of interrupted and full evaporation sequences can form a complex layering of different lithologies. Viscosity contrasts of up to five orders of magnitude between these different lithologies are possible in this environment. During the late stage of an evaporation cycle potassium and magnesium (K-Mg) salts are precipitated. These K-Mg salts are of economic interest but also a known drilling hazard due to their very low viscosity. How up to 200m thick layers of these evaporites affect salt deformation at different scales is not well known. A better understanding of salt tectonics with extreme mechanical stratification is needed for better exploration and production of potassium-magnesium salts and to predict the internal structure of potential nuclear waste repositories in salt. To gain a better understanding of the internal deformation of these layers we analyzed K-Mg salt rich drill cores out of the Zechstein III-1b subunit from the Veendam Pillow 10 km southeast of Groningen, near the city Veendam in the NE Netherlands. The study area has a complex geological history with multiple tectonic phases of extension and compression forming internal deformation in the pillow but also conserving most of the original layering. Beside halite the most common minerals in the ZIII-1b are carnallite, kieserite, anhydrite and bischofite alternating in thin layers of simple composition. Seismic interpretation revealed that the internal structure of the Veendam Pillow shows areas, in which the K-Mg salt rich ZIII 1b layer is much thicker than elsewhere, as a result of salt deformation. The internal structure of the ZIII-1b on the other hand, remains unknown. The core analysis shows a strong strain concentration in the weaker Bischofite (MgCl2*6H20) and Carnallite (KMgCl3*6H20) rich layers producing tectonic breccias and highly strained layers completely overprinting the original layering. Layers formed by alternating beds

ULNAR NEURITIS ASSOCIATED WITH GUN STOCK DEFORMITY FOLLOWING SUPRACONDYLAR FRACTURE OF HUMERUS

Directory of Open Access Journals (Sweden)

Sunita Morhan

2014-04-01

Full Text Available Background: This case report describes a patient who was referred to physiotherapist from a hand surgeon. Among the fractures around the elbow joint, radial head fracture and fracture of distal end of radius are common among adults. The occurrence of Supracondylar fractures are more commonly seen in children when compared to adults. One of the complications of this fracture is malunion resulting in Gun stock deformity. The main Purpose of this case report is to explore, 1. The complication associated with gunstock deformity 2. Chances of iatrogenic nerve injury after manipulation under anesthesia. 3.Long term supervised rehabilitation approach. Case Description: A 40 years old male patient referred to our Physiotherapy department by a hand surgeon. After the initial evaluation, findings revealed limitation in right elbow movement and tingling and numbness sensation in little and half of ring fingers in his right side. This patient underwent ulnar nerve transposition surgery followed by rehabilitation. His physiotherapy session includes electrotherapeutic agents for pain relief, passive mobilization of elbow and strengthening program for his flexors and extensors of elbow for a period of one year. Outcome: The outcome of the long term rehabilitation approach for a patient with ulnar neuropathy secondary to gunstock deformity after ulnar nerve transposition surgery is good. The patients tingling and numbness decreased and the range of elbow movement improved significantly. Discussion: Most common complications of fracture of distal end of humerus include malunion,ischemic contracture and nerve injuries. The relative incidence of iatrogenic nerve injuries associatedwith this fracture has been reported as being 2%-6%. Nerve injuries after Supracondylar humeral fractures occur primarily due to tenting or entrapment of the nerve on the sharp proximal humeral fragment, while iatrogenic injuries occur either during closed manipulation or percutaneous

Generalized Ehrenfest Relations, Deformation Quantization, and the Geometry of Inter-model Reduction

Science.gov (United States)

Rosaler, Joshua

2018-03-01

This study attempts to spell out more explicitly than has been done previously the connection between two types of formal correspondence that arise in the study of quantum-classical relations: one the one hand, deformation quantization and the associated continuity between quantum and classical algebras of observables in the limit \\hbar → 0, and, on the other, a certain generalization of Ehrenfest's Theorem and the result that expectation values of position and momentum evolve approximately classically for narrow wave packet states. While deformation quantization establishes a direct continuity between the abstract algebras of quantum and classical observables, the latter result makes in-eliminable reference to the quantum and classical state spaces on which these structures act—specifically, via restriction to narrow wave packet states. Here, we describe a certain geometrical re-formulation and extension of the result that expectation values evolve approximately classically for narrow wave packet states, which relies essentially on the postulates of deformation quantization, but describes a relationship between the actions of quantum and classical algebras and groups over their respective state spaces that is non-trivially distinct from deformation quantization. The goals of the discussion are partly pedagogical in that it aims to provide a clear, explicit synthesis of known results; however, the particular synthesis offered aspires to some novelty in its emphasis on a certain general type of mathematical and physical relationship between the state spaces of different models that represent the same physical system, and in the explicitness with which it details the above-mentioned connection between quantum and classical models.

Assessing physical function in adult acquired major upper-limb amputees by combining the Disabilities of the Arm, Shoulder and Hand (DASH) Outcome Questionnaire and clinical examination.

Science.gov (United States)

Ostlie, Kristin; Franklin, Rosemary J; Skjeldal, Ola H; Skrondal, Anders; Magnus, Per

2011-10-01

To describe physical function in adult acquired major upper-limb amputees (ULAs) by combining self-assessed arm function and physical measures obtained by clinical examinations; to estimate associations between background factors and self-assessed arm function in ULAs; and to assess whether clinical examination findings may be used to detect reduced arm function in unilateral ULAs. postal questionnaires and clinical examinations. Norwegian ULA population. Clinical examinations performed at 3 clinics. Questionnaires: population-based sample (n=224; 57.4% response rate). Clinical examinations: combined referred sample and convenience sample of questionnaire responders (n=70; 83.3% of those invited). SURVEY inclusion criteria: adult acquired major upper-limb amputation, resident in Norway, mastering of spoken and written Norwegian. Not applicable. The Disabilities of the Arm, Shoulder and Hand (DASH) Outcome Questionnaire, and clinical examination of joint motion and muscle strength with and without prostheses. Mean DASH score was 22.7 (95% confidence interval [CI], 20.3-25.0); in bilateral amputees, 35.7 (95% CI, 23.0-48.4); and in unilateral amputees, 22.1 (95% CI, 19.8-24.5). A lower unilateral DASH score (better function) was associated with paid employment (vs not in paid employment: adjusted regression coefficient [aB]=-5.40, P=.033; vs students: aB=-13.88, P=.022), increasing postamputation time (aB=-.27, P=.001), and Norwegian ethnicity (aB=-14.45, P<.001). At clinical examination, we found a high frequency of impaired neck mobility and varying frequencies of impaired joint motion and strength at the shoulder, elbow, and forearm level. Prosthesis wear was associated with impaired joint motion in all upper-limb joints (P<.006) and with reduced shoulder abduction strength (P=.002). Impaired without-prosthesis joint motion in shoulder flexion (ipsilateral: aB=12.19, P=.001) and shoulder abduction (ipsilateral: aB=12.01, P=.005; contralateral: aB=28.82, P=.004

Denmark: HAND in HAND Policy Questionnaire

DEFF Research Database (Denmark)

Laursen, Hilmar Dyrborg; Nielsen, Birgitte Lund

2018-01-01

Som del af det internationale EU finansierede projekt Hand in Hand, der fokuserer på de såkaldte SEI-kompetencer (Social, Emotional, Intercultural), er dansk policy i relation til elevernes sociale, emotionelle og interkulturelle læring kortlagt i denne rapport. Der refereres bl.a. til "elevernes...

SU-E-J-42: Customized Deformable Image Registration Using Open-Source Software SlicerRT

Energy Technology Data Exchange (ETDEWEB)

Gaitan, J Cifuentes; Chin, L; Pignol, J [Sunnybrook Health Sciences Centre, Toronto, Ontario (Canada); Kirby, N; Pouliot, J [UC San Francisco, San Francisco, CA (United States); Lasso, A; Pinter, C; Fichtinger, G [Queen' s University, Kingston, Ontario (Canada)

2014-06-01

Purpose: SlicerRT is a flexible platform that allows the user to incorporate the necessary images registration and processing tools to improve clinical workflow. This work validates the accuracy and the versatility of the deformable image registration algorithm of the free open-source software SlicerRT using a deformable physical pelvic phantom versus available commercial image fusion algorithms. Methods: Optical camera images of nonradiopaque markers implanted in an anatomical pelvic phantom were used to measure the ground-truth deformation and evaluate the theoretical deformations for several DIR algorithms. To perform the registration, full and empty bladder computed tomography (CT) images of the phantom were obtained and used as fixed and moving images, respectively. The DIR module, found in SlicerRT, used a B-spline deformable image registration with multiple optimization parameters that allowed customization of the registration including a regularization term that controlled the amount of local voxel displacement. The virtual deformation field at the center of the phantom was obtained and compared to the experimental ground-truth values. The parameters of SlicerRT were then varied to improve spatial accuracy. To quantify image similarity, the mean absolute difference (MAD) parameter using Hounsfield units was calculated. In addition, the Dice coefficient of the contoured rectum was evaluated to validate the strength of the algorithm to transfer anatomical contours. Results: Overall, SlicerRT achieved one of the lowest MAD values across the algorithm spectrum, but slightly smaller mean spatial errors in comparison to MIM software (MIM). On the other hand, SlicerRT created higher mean spatial errors than Velocity Medical Solutions (VEL), although obtaining an improvement on the DICE to 0.91. The large spatial errors were attributed to the poor contrast in the prostate bladder interface of the phantom. Conclusion: Based phantom validation, SlicerRT is capable of

Deformation-induced structural changes of amorphous Ni0.5Zr0.5 in molecular-dynamic simulations

International Nuclear Information System (INIS)

Brinkmann, K.

2006-01-01

The present work investigates the plastic deformation of metallic glasses by the aid of molecular-dynamic simulations. The parameters for the model system are adapted to those for a NiZr-alloy. In particular, the composition Ni 0.5 Zr 0.5 is used. The analyzed deformation simulations are conducted for small systems with 5184 atoms and large systems with 17500 atoms in a periodic simulation cell. The deformation simulations of pre-deformed samples are carried out either at constant shear-rate or at constant load, the latter mode modeling a creep experiment. Stress-strain curves for pre-deformed samples show a less pronounced stress-overshoot phenomenon. Creep-simulations of samples deformed beyond the yield region indicate a drastically reduced viscosity in these systems when compared to samples pre-deformed only up to the linear regime of the stress-strain curve. From analyzing the local atomic topology it is found that the transition from the highly viscous, hard-to-deform state of the undeformed or only weakly strained system into the easy-to-deform flow-state, present if the system is strained far beyond the yielding regime of the stress-strain curve, is connected with the formation of a region containing atoms with massive changes in their topology which is oriented along a diagonal plane of the simulation cell. The degree of localization of these deformation bands is influenced by temperature and shear-rate. In subsequent deformations of pre-deformed samples the regions with massive changes in the atomic topology are again susceptible to changes in the local atomic topology. By using methods from statistics, a significant difference in the distribution of atomic properties for the group of atoms with massive topology changes on the one hand and the group of atoms without changes in their topology on the other gets quantitatively ascertainable. From the differences in structural properties, e.g. potential energy, cage volumes, angular order parameters or atomic

Optimization of dose in computerized radiology exams of the hands

International Nuclear Information System (INIS)

Pavan, Ana Luiza Menegatti; Alvarez, Matheus; Alves, Allan Felipe Fattori; Dela Rosa, Maria Eugenia; Miranda, Jose Ricardo de Arruda

2014-01-01

Fractures and dislocations of the hand are some of the most frequently encountered injuries of the musculoskeletal system traumas. To evaluate these lesions radiography is the investigation of choice, and is rarely needed the help of other images to establish the diagnosis and treatment. The image quality of the X-ray examination is therefore essential. In this study a homogeneous phantom hand was developed for use in the hand image optimization process. In this procedure were quantified for different tissue thicknesses which are an anthropomorphic hand phantom. To perform the classification and quantification of tissue was applied membership functions in histograms of CT scans. The same procedure was adopted for 30 retrospective examinations of patients in the Hospital of the Faculty of Medicine of Botucatu UNESP (HCFMB-UNESP). The homogeneous phantom built was used to calibrate the techniques used in clinical routine (RC). Such calibrated techniques were used to acquire images of anthropomorphic phantom. These images were analyzed by Visual Grading Method (VFA) by experienced radiologists in the area. The image with better grade in AGV and lower dose was chosen as the Gold Standard. The results showed concordance between the tissue thicknesses which constitute the anthropomorphic phantom and the sample evaluated patients, with variations between 12.63% and 6.48% for soft tissue and bone, respectively. The Gold Technical Standard compared with the technique normally used in the CR reduces dose charge 41.28% and 33.18% in the tube

q-deformed Minkowski space

International Nuclear Information System (INIS)

Ogievetsky, O.; Pillin, M.; Schmidke, W.B.; Wess, J.; Zumino, B.

1993-01-01

In this lecture I discuss the algebraic structure of a q-deformed four-vector space. It serves as a good example of quantizing Minkowski space. To give a physical interpretation of such a quantized Minkowski space we construct the Hilbert space representation and find that the relevant time and space operators have a discrete spectrum. Thus the q-deformed Minkowski space has a lattice structure. Nevertheless this lattice structure is compatible with the operation of q-deformed Lorentz transformations. The generators of the q-deformed Lorentz group can be represented as linear operators in the same Hilbert space. (orig.)

The beneficial effects of rehabilitation on hand function in patients with rheumatoid arthritis

Directory of Open Access Journals (Sweden)

Krystyna Księżopolska-Orłowska

2016-12-01

Full Text Available Objectives: The hand is one of the main elements of the rehabilitation of patients with rheumatoid arthritis (RA due to deformities, which occur in approximately 90% of patients. It is a serious problem, both in the psychological and functional aspect, connected with muscle strength reduction, a limited range of motion and non-acceptance of the changes in the shape of the limb. The study aimed to assess the effect of rehabilitation on the function of the hand in rheumatoid arthritis. Material and methods: The study group consisted of 40 women with RA. The patients had been previously treated at the Rehabilitation Department of the National Institute of Geriatrics, Rheumatology and Rehabilitation in Warsaw. The study group underwent 3 weeks of rehabilitation involving individual therapy, exercises with equipment, patient education and physical therapy. The control group included women without a diagnosis of RA, hands pain-free and fully mobile. In both groups the hand was assessed for grip value, grip quality and manipulative ability. In the study group the basis of pain intensity was noted. The measurements were performed twice – prior to the rehabilitation and after 3 weeks of rehabilitation in women with RA and once in women without hand problems. Results : The results obtained revealed marked limitation of hand function in patients with rheumatoid arthritis. The treatment resulted in an improvement of all assessed parameters except cylindrical grip, in which only a part of the findings was statistically significant. Conclusions : The analysis of the study material showed that appropriately adjusted and conducted hand physiotherapy in women with rheumatoid arthritis contributed to the improvement of its function by pain reduction, improved value and quality of grip, and also increased manipulative ability.

Hand Surgery: Anesthesia

Science.gov (United States)

... All Topics A-Z Videos Infographics Symptom Picker Anatomy Bones Joints Muscles Nerves Vessels Tendons About Hand Surgery What is a Hand Surgeon? What is a Hand Therapist? Media Find a Hand Surgeon Home Anatomy Hand Surgery Anesthesia Email to a friend * required ...

Rotary deformity in degenerative spondylolisthesis

International Nuclear Information System (INIS)

Kang, Sung Gwon; Kim, Jeong; Kho, Hyen Sim; Yun, Sung Su; Oh, Jae Hee; Byen, Ju Nam; Kim, Young Chul

1994-01-01

We studied to determine whether the degenerative spondylolisthesis has rotary deformity in addition to forward displacement. We have made analysis of difference of rotary deformity between the 31 study groups of symptomatic degenerative spondylolisthesis and 31 control groups without any symptom, statistically. We also reviewed CT findings in 15 study groups. The mean rotary deformity in study groups was 6.1 degree(the standard deviation is 5.20), and the mean rotary deformity in control groups was 2.52 degree(the standard deviation is 2.16)(p < 0.01). The rotary deformity can be accompanied with degenerative spondylolisthesis. We may consider the rotary deformity as a cause of symptomatic degenerative spondylolisthesis in case that any other cause is not detected

Hand Anatomy

Science.gov (United States)

... All Topics A-Z Videos Infographics Symptom Picker Anatomy Bones Joints Muscles Nerves Vessels Tendons About Hand Surgery What is ... Hand Therapist? Media Find a Hand Surgeon Home Anatomy Bones Joints Muscles Nerves Vessels Tendons Anatomy The upper extremity is ...

Extremely deformable structures

CERN Document Server

2015-01-01

Recently, a new research stimulus has derived from the observation that soft structures, such as biological systems, but also rubber and gel, may work in a post critical regime, where elastic elements are subject to extreme deformations, though still exhibiting excellent mechanical performances. This is the realm of ‘extreme mechanics’, to which this book is addressed. The possibility of exploiting highly deformable structures opens new and unexpected technological possibilities. In particular, the challenge is the design of deformable and bi-stable mechanisms which can reach superior mechanical performances and can have a strong impact on several high-tech applications, including stretchable electronics, nanotube serpentines, deployable structures for aerospace engineering, cable deployment in the ocean, but also sensors and flexible actuators and vibration absorbers. Readers are introduced to a variety of interrelated topics involving the mechanics of extremely deformable structures, with emphasis on ...

Deforming tachyon kinks and tachyon potentials

International Nuclear Information System (INIS)

Afonso, Victor I.; Bazeia, Dionisio; Brito, Francisco A.

2006-01-01

In this paper we investigate deformation of tachyon potentials and tachyon kink solutions. We consider the deformation of a DBI type action with gauge and tachyon fields living on D1-brane and D3-brane world-volume. We deform tachyon potentials to get other consistent tachyon potentials by using properly a deformation function depending on the gauge field components. Resolutions of singular tachyon kinks via deformation and applications of deformed tachyon potentials to scalar cosmology scenario are discussed

An evaluation of hospital hand hygiene practice and glove use in Hong Kong.

Science.gov (United States)

Chau, Janita P-C; Thompson, David R; Twinn, Sheila; Lee, Diana T F; Pang, Sharon W M

2011-05-01

To identify omissions in hand hygiene practice and glove use among hospital workers in Hong Kong. Hospital-acquired infection is the commonest complication affecting hospitalised patients. Even though research evidence suggests that hand hygiene and proper glove use are the most important ways to prevent the spread of disease and infection, compliance with both are reported to be unacceptably low. An observational study of hospital workers in one acute and two convalescence and rehabilitation hospitals in Hong Kong was conducted. The participating clinical areas included the medical and surgical wards, accident and emergency department and intensive care unit. Hand hygiene practice and glove use amongst 206 hospital health and support workers, stratified according to years of working experience, were observed. The number of observed episodes for hand hygiene was 1037 and for glove use 304. Compliance with hand hygiene was 74.7% and with glove use 72.4%. In approximately two-third of episodes, participants washed their hands after each patient contact; though, 78.5% failed to rub their hands together vigorously for at least 15 seconds. The major break in compliance with glove use was failure to change gloves between procedures on the same patient. In 28.6% of observed glove use episodes, participants did not wear gloves during procedures that exposed them to blood, body fluids, excretion, non-intact skin or mucous membranes. Significant differences in performance scores on antiseptic hand rub were found between the two types of hospital and on glove use between the three groups of work experience: ≤ 5, 6-10, >10 years. Education and reinforcement of proper hand hygiene practice and glove use among hospital health and support workers is needed. © 2011 Blackwell Publishing Ltd.

Arthroplasty of the rheumatoid hand. Pre- and postoperative imaging with special consideration of biomechanical and pathobiomechanical aspects and its radiological evaluation; Arthroplastik der rheumatischen Hand. Prae- und postoperative Bildgebung mit besonderer Beruecksichtigung der Biomechanik und Pathobiomechanik und ihrer Evaluation am Roentgenbild

Energy Technology Data Exchange (ETDEWEB)

Sommer, O.J. [Krankenhaus Hietzing mit Neurologischem Zentrum Rosenhuegel, Zentralroentgeninstitut mit Schnittbildzentrum, Wien (Austria); Sekyra, K. [Medizinische Universitaet Innsbruck/Oesterreich, Klinik fuer Orthopaedie (Austria)

2006-09-15

Radiology plays a key role when the indications for arthroplasties of the hand and finger joints are determined and for the postoperative follow-up. On the one hand, the degree of inflammatory changes in all affected compartments is to be evaluated and graded; on the other hand, conventional radiograms allow for a first assessment of possible joint instability and impaired biomechanics. Both aspects influence the choice of the proper surgical therapeutic strategy. Osteolysis, deformity, fracture, prosthesis loosening or failure, heterotopic ossification, and foreign body-associated formation of granulation tissue are complications which can be detected on follow-up radiographs early on. (orig.) [German] Bei der Indikationsstellung und Verlaufskontrolle von Arthroplastien der Hand kommt der Radiologie eine wesentliche Rolle zu. Einerseits ist das Ausmass der entzuendlichen Veraenderungen in allen Kompartimenten umfassend zu beurteilen und graduieren, andererseits lassen sich bereits im konventionellen Roentgenbild Rueckschluesse auf etwaige Instabilitaet oder gestoerte Biomechanik ziehen. Beide Aussagen wirken sich auf die operative Therapieentscheidung massgeblich aus. Osteolyse, Deformitaet, Fraktur, Implantatlockerung oder -versagen, heterotope Knochenneubildung und fremdkoerperassoziierte Granulationsgewebebildung sind Komplikationen, die in den postoperativen Verlaufskontrollen fruehzeitig erfasst werden koennen. (orig.)

a Research on Monitoring Surface Deformation and Relationships with Surface Parameters in Qinghai Tibetan Plateau Permafrost

Science.gov (United States)

Mi, S. J.; Li, Y. T.; Wang, F.; Li, L.; Ge, Y.; Luo, L.; Zhang, C. L.; Chen, J. B.

2017-09-01

The Qinghai Tibetan Plateau permafrost has been the largest permafrost region in middle-low latitude in the world for its high altitude. For the large area permafrost, especially surface deformation brought by it, have serious influence on the road engineering, road maintaining and regional economic development. Consequently, it is essential to monitor the surface deformation and study factors that influent it. We monitored an area named Wudaoliang from July 25, 2015 to June 1, 2016 and 15 Sentinel images were obtained during this time. The area we chose is about 35 kilometers long and 2 kilometers wide, and the national road 109 of China passes through the area. The traditional PS-INSAR (Persistent Scatterer Interferometric Synthetic Aperture Radar) method is not suitable because less historical images in the research area and leading to the number of PS (Persistent Scatterer) points is not enough to obtain accurate deformation results. Therefore, in this paper, we used another method which named QUASI-PSInSAR (QUASI Persistent Scatterer Interferometric Synthetic Aperture Radar) to acquire deformation for it has the advantage to weaken or eliminate the effects of spatial and temporal correlation, which has proved by other scholar. After processing 15 images in the SARproz software, we got the conclusions that, 1) the biggest deformation velocity in the whole area was about 127.9mm/year and about 109.3 mm/year in the road; 2) apparent deformation which have surface deformation more than 30mm/year was about 1.7Km in the road. Meanwhile, soil moisture(SM), Land surface temperature (LST) and surface water(SW), which are primary parameters of the land surface over the same time were reversed by using Sentinel data, Landsat data and ZY-3 data, respectively. After analyzing SM, LST , SW and deformation, we obtained that wet areas which had bigger SM, lower LST and more SW, had greater percentage of severe deformation than arid areas; besides, deformation pattern were

q-deformed Brownian motion

CERN Document Server

Man'ko, V I

1993-01-01

Brownian motion may be embedded in the Fock space of bosonic free field in one dimension.Extending this correspondence to a family of creation and annihilation operators satisfying a q-deformed algebra, the notion of q-deformation is carried from the algebra to the domain of stochastic processes.The properties of q-deformed Brownian motion, in particular its non-Gaussian nature and cumulant structure,are established.

Strategy and your stronger hand.

Science.gov (United States)

Moore, Geoffrey A

2005-12-01

There are two kinds of businesses in the world, says the author. Knowing what they are--and which one your company is--will guide you to the right strategic moves. One kind includes businesses that compete on a complex-systems model. These companies have large enterprises as their primary customers. They seek to grow a customer base in the thousands, with no more than a handful of transactions per customer per year (indeed, in some years there may be none), and the average price per transaction ranges from six to seven figures. In this model, 1,000 enterprises each paying dollar 1 million per year would generate dollar 1 billion in annual revenue. The other kind of business competes on a volume-operations model. Here, vendors seek to acquire millions of customers, with tens or even hundreds of transactions per customer per year, at an average price of relatively few dollars per transaction. Under this model, it would take 10 million customers each spending dollar 8 per month to generate nearly dollar 1 billion in revenue. An examination of both models shows that they could not be further apart in their approach to every step along the classic value chain. The problem, though, is that companies in one camp often attempt to create new value by venturing into the other. In doing so, they fail to realize how their managerial habits have been shaped by the model they've grown up with. By analogy, they have a "handedness"--the equivalent of a person's right- or left-hand dominance--that makes them as adroit in one mode as they are awkward in the other. Unless you are in an industry whose structure forces you to attempt ambidexterity (in which case, special efforts are required to manage the inevitable dropped balls), you'll be far more successful making moves that favor your stronger hand.

In-situ studies of bulk deformation structures: Static properties under load and dynamics during deformation

DEFF Research Database (Denmark)

Jakobsen, Bo

2006-01-01

The main goal of the study presented in this thesis was to perform in-situ investigations on deformation structures in plastically deformed polycrystalline copper at low degrees of tensile deformation (model system for cell forming pure fcc metals. Anovel synchrotron...... grains in polycrystalline samples during tensile deformation. We have shown that the resulting 3D reciprocal space maps from tensile deformed copper comprise a pronounced structure, consisting of bright sharp peaks superimposed on a cloud of enhanced intensity. Based on the integrated intensity......, the width of the peaks, and spatial scanning experiments it is concluded that the individual peaks arise from individual dislocation-free regions (the subgrains) in the dislocation structure. The cloud is attributed to the dislocation rich walls. Samples deformed to 2% tensile strain were investigated under...

Effect of alloy deformation on the average spacing parameters of non-deforming particles

International Nuclear Information System (INIS)

Fisher, J.; Gurland, J.

1980-02-01

It is shown on the basis of stereological definitions and a few simple experiments that the commonly used average dispersion parameters, area fraction (A/sub A/)/sub β/, areal particle density N/sub Aβ/ and mean free path lambda/sub α/, remain invariant during plastic deformation in the case of non-deforming equiaxed particles. Directional effects on the spacing parameters N/sub Aβ/ and lambda/sub α/ arise during uniaxial deformation by rotation and preferred orientation of nonequiaxed particles. Particle arrangement in stringered or layered structures and the effect of deformation on nearest neighbor distances of particles and voids are briefly discussed in relation to strength and fracture theories

Disseminated cryptococcosis and fluconazole resistant oral candidiasis in a patient with acquired immunodeficiency syndrome (AIDS).

Science.gov (United States)

Kothavade, Rajendra J; Oberai, Chetan M; Valand, Arvind G; Panthaki, Mehroo H

2010-10-28

Disseminated cryptococcosis and recurrent oral candidiasis was presented in a-heterosexual AIDS patient. Candida tropicalis (C.tropicalis) was isolated from the oral pseudomembranous plaques and Cryptococcus neoformans (C. neoformans) was isolated from maculopapular lesions on body parts (face, hands and chest) and body fluids (urine, expectorated sputum, and cerebrospinal fluid). In vitro drug susceptibility testing on the yeast isolates demonstrated resistance to fluconazole acquired by C. tropicalis which was a suggestive possible root cause of recurrent oral candidiasis in this patient.

InSAR observation of seasonal ground surface deformation in permafrost area near Batagay, Siberia

Science.gov (United States)

Yanagiya, K.; Furuya, M.

2017-12-01

Thawing of permafrost can lead to ground deformation. Ground deformation has been studied as a serious problem in the Arctic Ocean coastal area such as Russia for a long time, because the deformation causes damage to architectures at these areas. However, there have been no quantitative observation data, and the spatial and temporal distributions have hardly been investigated. On the other hand, by the recently global warming influence, the importance of organic carbon stored in permafrost is pointed out. Although the release of methane gas is confirmed in some thermokarst lakes, it is very difficult to observe the permafrost in a wide area by field study. Instead, it is technically possible to monitor the subsidence and uplift of the ground over the permafrost area, which could potentially make a significant contribution to the monitoring thawing process of permafrost. In this study, we attempted to detect ground deformation signal in permafrost area by remote sensing using interferometric synthetic aperture radar (InSAR). Using the data of two SAR satellites ALOS and ALOS2 launched by JAXA, we observed recent ground deformation from 2007 to 2016. Particularly recent observations of ALOS2 from 2014 to 2016 discovered distant displacements towards the LOS direction in the northeast region from the town of Batagay,Siberia. The diameter of the displacements area covers about 7.7 km. In this study, we considered that this signal is likely to be due to permafrost thawing, we also investigated the seasonal characteristics and looked back ALOS data of this area. In addition, since the high latitude area, observation results include noise due to the ionosphere, so we tried to remove the noise.

Seeing mathematics: perceptual experience and brain activity in acquired synesthesia.

Science.gov (United States)

Brogaard, Berit; Vanni, Simo; Silvanto, Juha

2013-01-01

We studied the patient JP who has exceptional abilities to draw complex geometrical images by hand and a form of acquired synesthesia for mathematical formulas and objects, which he perceives as geometrical figures. JP sees all smooth curvatures as discrete lines, similarly regardless of scale. We carried out two preliminary investigations to establish the perceptual nature of synesthetic experience and to investigate the neural basis of this phenomenon. In a functional magnetic resonance imaging (fMRI) study, image-inducing formulas produced larger fMRI responses than non-image inducing formulas in the left temporal, parietal and frontal lobes. Thus our main finding is that the activation associated with his experience of complex geometrical images emerging from mathematical formulas is restricted to the left hemisphere.

Cosmetic and Functional Nasal Deformities

Science.gov (United States)

... nasal complaints. Nasal deformity can be categorized as “cosmetic” or “functional.” Cosmetic deformity of the nose results in a less ... taste , nose bleeds and/or recurrent sinusitis . A cosmetic or functional nasal deformity may occur secondary to ...

Robotic hand project

OpenAIRE

Karaçizmeli, Cengiz; Çakır, Gökçe; Tükel, Dilek

2014-01-01

In this work, the mechatronic based robotic hand is controlled by the position data taken from the glove which has flex sensors mounted to capture finger bending of the human hand. The angular movement of human hand’s fingers are perceived and processed by a microcontroller, and the robotic hand is controlled by actuating servo motors. It has seen that robotic hand can simulate the movement of the human hand that put on the glove, during tests have done. This robotic hand can be used not only...

Clean Hands Count

Medline Plus

Full Text Available ... has been rented. This feature is not available right now. Please try again later. Published on May ... 34 How The Clean Hands - Safe Hands System Works - Duration: 3:38. Clean Hands-Safe Hands 5, ...

Normal values for myocardial deformation within the right heart measured by feature-tracking cardiovascular magnetic resonance imaging.

Science.gov (United States)

Liu, Boyang; Dardeer, Ahmed M; Moody, William E; Edwards, Nicola C; Hudsmith, Lucy E; Steeds, Richard P

2018-02-01

Reproducible and repeatable assessment of right heart function is vital for monitoring congenital and acquired heart disease. There is increasing evidence for the additional value of myocardial deformation (strain and strain rate) in determining prognosis. This study aims to determine the reproducibility of deformation analyses in the right heart using cardiovascular magnetic resonance feature tracking (FT-CMR); and to establish normal ranges within an adult population. A cohort of 100 healthy subjects containing 10 males and 10 females from each decade of life between the ages of 20 and 70 without known congenital or acquired cardiovascular disease, hypertension, diabetes, dyslipidaemia or renal, hepatic, haematologic and systemic inflammatory disorders underwent FT-CMR assessment of right ventricular (RV) and right atrial (RA) myocardial strain and strain rate. RV longitudinal strain (Ell) was -21.9±3.24% (FW+S Ell) and -24.2±3.59% (FW-Ell). Peak systolic strain rate (S') was -1.45±0.39s -1 (FW+S) and -1.54±0.41s -1 (FW). Early diastolic strain rate (E') was 1.04±0.26s -1 (FW+S) and 1.04±0.33s -1 (FW). Late diastolic strain rate (A') was 0.94±0.33s -1 (FW+S) and 1.08±0.33s -1 (FW). RA peak strain was -21.1±3.76%. The intra- and inter-observer ICC for RV Ell (FW+S) was 0.92 and 0.80 respectively, while for RA peak strain was 0.92 and 0.89 respectively. Normal values of RV & RA deformation for healthy individuals using FT-CMR are provided with good RV Ell and RA peak strain reproducibility. Strain rate suffered from sub-optimal reproducibility and may not be satisfactory for clinical use. Copyright © 2017 The Authors. Published by Elsevier B.V. All rights reserved.

Differences in the cyclic deformation behaviour of quenched and tempered steel 42 CrMo 4 (AISI 4140) due to stress- and strain-control; Versuchsfuehrungsbedingte Unterschiede im zyklischen Verformungsverhalten von verguetetem 42 CrMo 4 bei Spannungs- und Totaldehnungskontrolle

Energy Technology Data Exchange (ETDEWEB)

Schulze, V.; Lang, K.-H.; Voehringer, O.; Macherauch, E. [Karlsruhe Univ. (T.H.) (Germany). Inst. fuer Werkstoffkunde 1

1998-04-01

Cyclic stress-strain-curves and Manson-Coffin-plots of quenched and tempered steel 42 CrMo 4 (AISI 4140) strongly depend on whether they are determined under stress- or total-strain-control. At total-strain-controlled experiments, this is caused on the one hand by comparatively high initial stress-amplitudes which lead to distinctive cyclic work softening. On the other hand, the occuring differences in the evolution of inhomogeneous deformation patterns at both types of loading, which can be recorded by means of photoelasticity and microscopy, lead to differently distributed plastic deformations and to different integral values of plastic strain. (orig.) 11 refs.

Deformation-induced crystallographic-preferred orientation of hcp-iron: An experimental study using a deformation-DIA apparatus

Science.gov (United States)

Nishihara, Yu; Ohuchi, Tomohiro; Kawazoe, Takaaki; Seto, Yusuke; Maruyama, Genta; Higo, Yuji; Funakoshi, Ken-ichi; Tange, Yoshinori; Irifune, Tetsuo

2018-05-01

Shear and uniaxial deformation experiments on hexagonal close-packed iron (hcp-Fe) was conducted using a deformation-DIA apparatus at a pressure of 13-17 GPa and a temperature of 723 K to determine its deformation-induced crystallographic-preferred orientation (CPO). Development of the CPO in the deforming sample is determined in-situ based on two-dimensional X-ray diffraction using monochromatic synchrotron X-rays. In the shear deformation geometry, the and axes gradually align to be sub-parallel to the shear plane normal and shear direction, respectively, from the initial random texture. In the uniaxial compression and tensile geometry, the and axes, respectively, gradually align along the direction of the uniaxial deformation axis. These results suggest that basal slip (0001) is the dominant slip system in hcp-Fe under the studied deformation conditions. The P-wave anisotropy for a shear deformed sample was calculated using elastic constants at the inner core condition by recent ab-initio calculations. Strength of the calculated anisotropy was comparable to or higher than axisymmetric anisotropy in Earth's inner core.

Clamped end conditions and cross section deformation in the finite element absolute nodal coordinate formulation

International Nuclear Information System (INIS)

Hussein, Bassam A.; Weed, David; Shabana, Ahmed A.

2009-01-01

In the finite element absolute nodal coordinate formulation (ANCF), the elimination of the relative translations and rotations at a point does not necessarily define a fully clamped joint, particularly in the case of fully parameterized ANCF finite elements that allow for the deformation of the cross section. In this investigation, the formulations and results of two different sets of clamped end conditions that define two different joints are compared. The first joint, called the partially clamped joint, eliminates only the translations and rotations at a point on the cross section. The second joint, called the fully clamped joint, eliminates all the translation, rotation and deformation degrees of freedom at a point on the cross section. The kinematic equations that define the partially and fully clamped joints are developed, and the dynamic equations used in the comparative numerical study presented in this paper are shown. As discussed in this investigation, the fully clamped joint does not allow for the deformation of the cross section at the joint node since the gradient vectors remain orthogonal unit vectors. The partially clamped joint, on the other hand, allows for the deformation of the cross section. Nanson's formula is used as a measure of the deformation of the cross section in the case of the partially clamped joint. A very flexible pendulum that has a rigid body attached to its free end is used to compare the results of the partially and fully clamped joints. The numerical results obtained using this very flexible pendulum example show that, while the type of joint (partially or fully clamped) does not significantly affect the gross reference motion of the system, there are fundamental differences between the two joints since the partially clamped joint allows for the cross section deformations at the joint node

Neutron halo in deformed nuclei

International Nuclear Information System (INIS)

Zhou Shangui; Meng Jie; Ring, P.; Zhao Enguang

2010-01-01

Halo phenomena in deformed nuclei are investigated within a deformed relativistic Hartree Bogoliubov (DRHB) theory. These weakly bound quantum systems present interesting examples for the study of the interdependence between the deformation of the core and the particles in the halo. Contributions of the halo, deformation effects, and large spatial extensions of these systems are described in a fully self-consistent way by the DRHB equations in a spherical Woods-Saxon basis with the proper asymptotic behavior at a large distance from the nuclear center. Magnesium and neon isotopes are studied and detailed results are presented for the deformed neutron-rich and weakly bound nucleus 44 Mg. The core of this nucleus is prolate, but the halo has a slightly oblate shape. This indicates a decoupling of the halo orbitals from the deformation of the core. The generic conditions for the occurrence of this decoupling effects are discussed.

Radiographic and surgical considerations in arthritis surgery of the hand

International Nuclear Information System (INIS)

Nikac, Violeta; Weissman, Barbara N.; Blazar, Philip; Earp, Brandon

2017-01-01

Indications for hand surgeries include unremitting joint pain, deformity and stiffness, often secondary to arthritis. Several surgical options are available, including arthrodesis (fusion) and joint arthroplasty. Classically arthrodesis is performed in situations with poor bone stock and supporting soft tissues. Arthroplasty is reserved for patients and joints in which preservation of function is important and bone stock and soft tissue support are adequate. In this article we will review various techniques for arthrodesis and arthroplasty, their post-surgical imaging appearance, including key findings important to surgeons, and the findings that indicate post-surgical complications. Radiographs are the mainstay for postoperative evaluation and will be the focus of the imaging portions of this review. Advanced imaging modalities will be reviewed when applicable. (orig.)

Radiographic and surgical considerations in arthritis surgery of the hand

Energy Technology Data Exchange (ETDEWEB)

Nikac, Violeta; Weissman, Barbara N. [Harvard Medical School, Brigham and Women' s Hospital, Department of Radiology, Boston, MA (United States); Blazar, Philip; Earp, Brandon [Harvard Medical School, Brigham and Women' s Hospital, Department of Orthopedics, Boston, MA (United States)

2017-05-15

Indications for hand surgeries include unremitting joint pain, deformity and stiffness, often secondary to arthritis. Several surgical options are available, including arthrodesis (fusion) and joint arthroplasty. Classically arthrodesis is performed in situations with poor bone stock and supporting soft tissues. Arthroplasty is reserved for patients and joints in which preservation of function is important and bone stock and soft tissue support are adequate. In this article we will review various techniques for arthrodesis and arthroplasty, their post-surgical imaging appearance, including key findings important to surgeons, and the findings that indicate post-surgical complications. Radiographs are the mainstay for postoperative evaluation and will be the focus of the imaging portions of this review. Advanced imaging modalities will be reviewed when applicable. (orig.)

Interactions of reactor helium and simulating gas mixtures with high-temperature metals with particular regard to simultaneous deformation

International Nuclear Information System (INIS)

Berchtold, L.

1983-01-01

For the observation of multicomponent alloys (Inconel 617 and 713LC, chroman (Ni20Cr), vacromium (Ni20Cr+Si), TZM) in multicomponent HTR atmospheres (HHT search gas), interaction between gases and metals was studied, both in theoretical descriptions and experimentally. From the experimental viewpoint, gradual simplification employs, on the one hand, tests effected in undiluted atmospheres with exclusively oxidizing or carburizing properties; on the other hand, more simple alloys and pure metals are applied specifically in the helium atmosphere. For an evaluation of the materials, it is maintained that in a strongly oxidizing (H 2 O-rich) atmosphere, e.g. in HHT search gas, materials with sufficient chrome content (e.g. 20% Cr in Ni alloys such as IN 617) offer favourable conditions for an almost complete interruption of carburizing reactions. In that case, the maintenance of the shielding effect of coating during rapid deformation and a tendency to planar delamination during deformation, which becomes stronger as the layer thickness increases, appear to be critical. Concentrations of oxide-forming agents stronger than chromium offer disadvantages rather than advantages. Owing to its tendency to flake off as the covering oxide SiO 2 or as part of a cover layer, silicon may more than destroy the light advantage of a slowed down process of carbon diffusion. The cast alloy IN 713LC shows a deep-reaching carburation in HHT search gas, both with and without deformation. No deep-reaching corrosive damage is noticeable on the molybdenum alloy TZM. (orig./MM) [de

A NEW APPROACH FOR SUBWAY TUNNEL DEFORMATION MONITORING: HIGH-RESOLUTION TERRESTRIAL LASER SCANNING

Directory of Open Access Journals (Sweden)

J. Li

2012-07-01

Full Text Available With the improvement of the accuracy and efficiency of laser scanning technology, high-resolution terrestrial laser scanning (TLS technology can obtain high precise points-cloud and density distribution and can be applied to high-precision deformation monitoring of subway tunnels and high-speed railway bridges and other fields. In this paper, a new approach using a points-cloud segmentation method based on vectors of neighbor points and surface fitting method based on moving least squares was proposed and applied to subway tunnel deformation monitoring in Tianjin combined with a new high-resolution terrestrial laser scanner (Riegl VZ-400. There were three main procedures. Firstly, a points-cloud consisted of several scanning was registered by linearized iterative least squares approach to improve the accuracy of registration, and several control points were acquired by total stations (TS and then adjusted. Secondly, the registered points-cloud was resampled and segmented based on vectors of neighbor points to select suitable points. Thirdly, the selected points were used to fit the subway tunnel surface with moving least squares algorithm. Then a series of parallel sections obtained from temporal series of fitting tunnel surfaces were compared to analysis the deformation. Finally, the results of the approach in z direction were compared with the fiber optical displacement sensor approach and the results in x, y directions were compared with TS respectively, and comparison results showed the accuracy errors of x, y, z directions were respectively about 1.5 mm, 2 mm, 1 mm. Therefore the new approach using high-resolution TLS can meet the demand of subway tunnel deformation monitoring.

Mechanics of deformable bodies

CERN Document Server

Sommerfeld, Arnold Johannes Wilhelm

1950-01-01

Mechanics of Deformable Bodies: Lectures on Theoretical Physics, Volume II covers topics on the mechanics of deformable bodies. The book discusses the kinematics, statics, and dynamics of deformable bodies; the vortex theory; as well as the theory of waves. The text also describes the flow with given boundaries. Supplementary notes on selected hydrodynamic problems and supplements to the theory of elasticity are provided. Physicists, mathematicians, and students taking related courses will find the book useful.

Quantum deformed magnon kinematics

OpenAIRE

Gómez, César; Hernández Redondo, Rafael

2007-01-01

The dispersion relation for planar N=4 supersymmetric Yang-Mills is identified with the Casimir of a quantum deformed two-dimensional kinematical symmetry, E_q(1,1). The quantum deformed symmetry algebra is generated by the momentum, energy and boost, with deformation parameter q=e^{2\\pi i/\\lambda}. Representing the boost as the infinitesimal generator for translations on the rapidity space leads to an elliptic uniformization with crossing transformations implemented through translations by t...

Thorax deformity, joint hypermobility and anxiety disorder

International Nuclear Information System (INIS)

Gulsun, M.; Dumlu, K.; Erbas, M.; Yilmaz, Mehmet B.; Pinar, M.; Tonbul, M.; Celik, C.; Ozdemir, B.

2007-01-01

Objective was to evaluate the association between thorax deformities, panic disorder and joint hypermobility. The study includes 52 males diagnosed with thorax deformity, and 40 healthy male controls without thorax deformity, in Tatvan Bitlis and Isparta, Turkey. The study was carried out from 2004 to 2006. The teleradiographic and thoracic lateral images of the subjects were evaluated to obtain the Beighton scores; subjects psychiatric conditions were evaluated using the Structured Clinical Interview for DSM-IV Axis I Disorders (SCID-1), and the Hamilton Anxiety Scale (HAM-A) was applied in order to determine the anxiety levels. Both the subjects and controls were compared in sociodemographic, anxiety levels and joint mobility levels. In addition, males with joint hypermobility and thorax deformity were compared to the group with thorax deformity without joint hypermobility. A significant difference in HAM-A scores was found between the groups with thorax deformity and without. In addition, 21 subjects with thorax deformity met the joint hypermobility criteria in the group with thorax deformity and 7 subjects without thorax deformity met the joint hypermobility criteria in the group without thorax deformity, according to Beighton scoring. The Beighton score of subjects with thorax deformity were significantly different from those of the group without deformity. Additionally, anxiety scores of the males with thorax deformity and joint hypermobility were found higher than males with thorax deformity without joint hypermobility. Anxiety disorders, particularly panic disorder, have a significantly higher distribution in males subjects with thorax deformity compared to the healthy control group. In addition, the anxiety level of males with thorax deformity and joint hypermobility is higher than males with thorax deformity without joint hypermobility. (author)

Deformed configurations, band structures and spectroscopic ...

Indian Academy of Sciences (India)

2014-03-20

Mar 20, 2014 ... The deformed configurations and rotational band structures in =50 Ge and Se nuclei are studied by deformed Hartree–Fock with quadrupole constraint and angular momentum projection. Apart from the `almost' spherical HF solution, a well-deformed configuration occurs at low excitation. A deformed ...

SU-E-J-222: Evaluation of Deformable Registration of PET/CT Images for Cervical Cancer Brachytherapy

International Nuclear Information System (INIS)

Liao, Y; Turian, J; Templeton, A; Kiel, K; Chu, J; Kadir, T

2014-01-01

Purpose: PET/CT provides important functional information for radiotherapy targeting of cervical cancer. However, repeated PET/CT procedures for external beam and subsequent brachytherapy expose patients to additional radiation and are not cost effective. Our goal is to investigate the possibility of propagating PET-active volumes for brachytherapy procedures through deformable image registration (DIR) of earlier PET/CT and ultimately to minimize the number of PET/CT image sessions required. Methods: Nine cervical cancer patients each received their brachytherapy preplanning PET/CT at the end of EBRT with a Syed template in place. The planning PET/CT was acquired on the day of brachytherapy treatment with the actual applicator (Syed or Tandem and Ring) and rigidly registered. The PET/CT images were then deformably registered creating a third (deformed) image set for target prediction. Regions of interest with standardized uptake values (SUV) greater than 65% of maximum SUV were contoured as target volumes in all three sets of PET images. The predictive value of the registered images was evaluated by comparing the preplanning and deformed PET volumes with the planning PET volume using Dice's coefficient (DC) and center-of-mass (COM) displacement. Results: The average DCs were 0.12±0.14 and 0.19±0.16 for rigid and deformable predicted target volumes, respectively. The average COM displacements were 1.9±0.9 cm and 1.7±0.7 cm for rigid and deformable registration, respectively. The DCs were improved by deformable registration, however, both were lower than published data for DIR in other modalities and clinical sites. Anatomical changes caused by different brachytherapy applicators could have posed a challenge to the DIR algorithm. The physiological change from interstitial needle placement may also contribute to lower DC. Conclusion: The clinical use of DIR in PET/CT for cervical cancer brachytherapy appears to be limited by applicator choice and requires further

Diffeomorphic Statistical Deformation Models

DEFF Research Database (Denmark)

Hansen, Michael Sass; Hansen, Mads/Fogtman; Larsen, Rasmus

2007-01-01

In this paper we present a new method for constructing diffeomorphic statistical deformation models in arbitrary dimensional images with a nonlinear generative model and a linear parameter space. Our deformation model is a modified version of the diffeomorphic model introduced by Cootes et al....... The modifications ensure that no boundary restriction has to be enforced on the parameter space to prevent folds or tears in the deformation field. For straightforward statistical analysis, principal component analysis and sparse methods, we assume that the parameters for a class of deformations lie on a linear...... with ground truth in form of manual expert annotations, and compared to Cootes's model. We anticipate applications in unconstrained diffeomorphic synthesis of images, e.g. for tracking, segmentation, registration or classification purposes....

Modular Hamiltonians for deformed half-spaces and the averaged null energy condition

Science.gov (United States)

Faulkner, Thomas; Leigh, Robert G.; Parrikar, Onkar; Wang, Huajia

2016-09-01

We study modular Hamiltonians corresponding to the vacuum state for deformed half-spaces in relativistic quantum field theories on {{R}}^{1,d-1} . We show that in addition to the usual boost generator, there is a contribution to the modular Hamiltonian at first order in the shape deformation, proportional to the integral of the null components of the stress tensor along the Rindler horizon. We use this fact along with monotonicity of relative entropy to prove the averaged null energy condition in Minkowski space-time. This subsequently gives a new proof of the Hofman-Maldacena bounds on the parameters appearing in CFT three-point functions. Our main technical advance involves adapting newly developed perturbative methods for calculating entanglement entropy to the problem at hand. These methods were recently used to prove certain results on the shape dependence of entanglement in CFTs and here we generalize these results to excited states and real time dynamics. We also discuss the AdS/CFT counterpart of this result, making connection with the recently proposed gravitational dual for modular Hamiltonians in holographic theories.

Deformation mechanisms in the San Andreas Fault zone - a comparison between natural and experimentally deformed microstructures

Science.gov (United States)

van Diggelen, Esther; Holdsworth, Robert; de Bresser, Hans; Spiers, Chris

2010-05-01

The San Andreas Fault (SAF) in California marks the boundary between the Pacific plate and the North American plate. The San Andreas Fault Observatory at Depth (SAFOD) is located 9 km northwest of the town of Parkfield, CA and provide an extensive set of samples through the SAF. The SAFOD drill hole encountered different lithologies, including arkosic sediments from the Salinian block (Pacific plate) and claystones and siltstones from the Great Valley block (North American plate). Fault deformation in the area is mainly by a combination of micro-earthquakes and fault creep. Deformation of the borehole casing indicated that the SAFOD drill hole cross cuts two actively deforming strands of the SAF. In order to determine the deformation mechanisms in the actively creeping fault segments, we have studied thin sections obtained from SAFOD phase 3 core material using optical and electron microscopy, and we have compared these natural SAFOD microstructures with microstructures developed in simulated fault gouges deformed in laboratory shear experiments. The phase 3 core material is divided in three different core intervals consisting of different lithologies. Core interval 1 consists of mildly deformed Salinian rocks that show evidence of cataclasis, pressure solution and reaction of feldspar to form phyllosilicates, all common processes in upper crustal rocks. Most of Core interval 3 (Great Valley) is also only mildly deformed and very similar to Core interval 1. Bedding and some sedimentary features are still visible, together with limited evidence for cataclasis and pressure solution, and reaction of feldspar to form phyllosilicates. However, in between the relatively undeformed rocks, Core interval 3 encountered a zone of foliated fault gouge, consisting mostly of phyllosilicates. This zone is correlated with one of the zones of localized deformation of the borehole casing, i.e. with an actively deforming strand of the SAF. The fault gouge zone shows a strong, chaotic

In situ room temperature tensile deformation of a 1% CrMoV bainitic steel using synchrotron and neutron diffraction

Energy Technology Data Exchange (ETDEWEB)

Weisser, M.A. [Paul Scherrer Institut, CH-5232 Villigen (Switzerland); Ecole Polytechnique Federale de Lausanne (EPFL), Institute of Materials (IMX), CH-1012 Lausanne (Switzerland); Evans, A.D.; Van Petegem, S. [Paul Scherrer Institut, CH-5232 Villigen (Switzerland); Holdsworth, S.R. [EMPA Materials Science and Technology, CH-8600 Duebendorf (Switzerland); Van Swygenhoven, H., E-mail: helena.vs@psi.ch [Paul Scherrer Institut, CH-5232 Villigen (Switzerland); Ecole Polytechnique Federale de Lausanne (EPFL), Institute of Materials (IMX), CH-1012 Lausanne (Switzerland)

2011-06-15

Neutron and synchrotron X-ray diffraction spectra have been acquired during room temperature tensile deformation of a creep-resistant bainitic 1% CrMoV steel, in order to study the evolution of internal microstresses and load-sharing mechanisms between the ferrite matrix and the various carbides. Cementite takes load from the plastifying matrix at the onset of macroscopic plasticity resulting in residual interphase stresses. Single peak fitting indicates an elastic anisotropic behaviour of cementite.

Performance of 12 DIR algorithms in low-contrast regions for mass and density conserving deformation

International Nuclear Information System (INIS)

Yeo, U. J.; Supple, J. R.; Franich, R. D.; Taylor, M. L.; Smith, R.; Kron, T.

2013-01-01

Purpose: Deformable image registration (DIR) has become a key tool for adaptive radiotherapy to account for inter- and intrafraction organ deformation. Of contemporary interest, the application to deformable dose accumulation requires accurate deformation even in low contrast regions where dose gradients may exist within near-uniform tissues. One expects high-contrast features to generally be deformed more accurately by DIR algorithms. The authors systematically assess the accuracy of 12 DIR algorithms and quantitatively examine, in particular, low-contrast regions, where accuracy has not previously been established.Methods: This work investigates DIR algorithms in three dimensions using deformable gel (DEFGEL) [U. J. Yeo, M. L. Taylor, L. Dunn, R. L. Smith, T. Kron, and R. D. Franich, “A novel methodology for 3D deformable dosimetry,” Med. Phys. 39, 2203–2213 (2012)], for application to mass- and density-conserving deformations. CT images of DEFGEL phantoms with 16 fiducial markers (FMs) implanted were acquired in deformed and undeformed states for three different representative deformation geometries. Nonrigid image registration was performed using 12 common algorithms in the public domain. The optimum parameter setup was identified for each algorithm and each was tested for deformation accuracy in three scenarios: (I) original images of the DEFGEL with 16 FMs; (II) images with eight of the FMs mathematically erased; and (III) images with all FMs mathematically erased. The deformation vector fields obtained for scenarios II and III were then applied to the original images containing all 16 FMs. The locations of the FMs estimated by the algorithms were compared to actual locations determined by CT imaging. The accuracy of the algorithms was assessed by evaluation of three-dimensional vectors between true marker locations and predicted marker locations.Results: The mean magnitude of 16 error vectors per sample ranged from 0.3 to 3.7, 1.0 to 6.3, and 1.3 to 7

Interfacial Bubble Deformations

Science.gov (United States)

Seymour, Brian; Shabane, Parvis; Cypull, Olivia; Cheng, Shengfeng; Feitosa, Klebert

Soap bubbles floating at an air-water experience deformations as a result of surface tension and hydrostatic forces. In this experiment, we investigate the nature of such deformations by taking cross-sectional images of bubbles of different volumes. The results show that as their volume increases, bubbles transition from spherical to hemispherical shape. The deformation of the interface also changes with bubble volume with the capillary rise converging to the capillary length as volume increases. The profile of the top and bottom of the bubble and the capillary rise are completely determined by the volume and pressure differences. James Madison University Department of Physics and Astronomy, 4VA Consortium, Research Corporation for Advancement of Science.

Deformation behaviour of turbine foundations

International Nuclear Information System (INIS)

Koch, W.; Klitzing, R.; Pietzonka, R.; Wehr, J.

1979-01-01

The effects of foundation deformation on alignment in turbine generator sets have gained significance with the transition to modern units at the limit of design possibilities. It is therefore necessary to obtain clarification about the remaining operational variations of turbine foundations. Static measurement programmes, which cover both deformation processes as well as individual conditions of deformation are described in the paper. In order to explain the deformations measured structural engineering model calculations are being undertaken which indicate the effect of limiting factors. (orig.) [de

Late-Paleozoic-Mesozoic deformational and deformation related metamorphic structures of Kuznetsk-Altai region

Science.gov (United States)

Zinoviev, Sergei

2014-05-01

Kuznetsk-Altai region is a part of the Central Asian Orogenic Belt. The nature and formation mechanisms of the observed structure of Kuznetsk-Altai region are interpreted by the author as the consequence of convergence of Tuva-Mongolian and Junggar lithospheric block structures and energy of collision interaction between the blocks of crust in Late-Paleozoic-Mesozoic period. Tectonic zoning of Kuznetsk-Altai region is based on the principle of adequate description of geological medium (without methods of 'primary' state recovery). The initial indication of this convergence is the crust thickening in the zone of collision. On the surface the mechanisms of lateral compression form a regional elevation; with this elevation growth the 'mountain roots' start growing. With an approach of blocks an interblock elevation is divided into various fragments, and these fragments interact in the manner of collision. The physical expression of collision mechanisms are periodic pulses of seismic activity. The main tectonic consequence of the block convergence and collision of interblock units is formation of an ensemble of regional structures of the deformation type on the basis of previous 'pre-collision' geological substratum [Chikov et al., 2012]. This ensemble includes: 1) allochthonous and autochthonous blocks of weakly deformed substratum; 2) folded (folded-thrust) systems; 3) dynamic metamorphism zones of regional shears and main faults. Characteristic of the main structures includes: the position of sedimentary, magmatic and PT-metamorphic rocks, the degree of rock dynamometamorphism and variety rock body deformation, as well as the styles and concentrations of mechanic deformations. 1) block terranes have weakly elongated or isometric shape in plane, and they are the systems of block structures of pre-collision substratum separated by the younger zones of interblock deformations. They stand out among the main deformation systems, and the smallest are included into the

A GPU based high-resolution multilevel biomechanical head and neck model for validating deformable image registration

Energy Technology Data Exchange (ETDEWEB)

Neylon, J., E-mail: jneylon@mednet.ucla.edu; Qi, X.; Sheng, K.; Low, D. A.; Kupelian, P.; Santhanam, A. [Department of Radiation Oncology, University of California Los Angeles, 200 Medical Plaza, #B265, Los Angeles, California 90095 (United States); Staton, R.; Pukala, J.; Manon, R. [Department of Radiation Oncology, M.D. Anderson Cancer Center, Orlando, 1440 South Orange Avenue, Orlando, Florida 32808 (United States)

2015-01-15

be caused by the biomechanical deformation process. Accuracy and stability of the model response were validated using ground-truth simulations representing soft tissue behavior under local and global deformations. Numerical accuracy of the HN deformations was analyzed by applying nonrigid skeletal transformations acquired from interfraction kVCT images to the model’s skeletal structures and comparing the subsequent soft tissue deformations of the model with the clinical anatomy. Results: The GPU based framework enabled the model deformation to be performed at 60 frames/s, facilitating simulations of posture changes and physiological regressions at interactive speeds. The soft tissue response was accurate with a R{sup 2} value of >0.98 when compared to ground-truth global and local force deformation analysis. The deformation of the HN anatomy by the model agreed with the clinically observed deformations with an average correlation coefficient of 0.956. For a clinically relevant range of posture and physiological changes, the model deformations stabilized with an uncertainty of less than 0.01 mm. Conclusions: Documenting dose delivery for HN radiotherapy is essential accounting for posture and physiological changes. The biomechanical model discussed in this paper was able to deform in real-time, allowing interactive simulations and visualization of such changes. The model would allow patient specific validations of the DIR method and has the potential to be a significant aid in adaptive radiotherapy techniques.

A GPU based high-resolution multilevel biomechanical head and neck model for validating deformable image registration

International Nuclear Information System (INIS)

Neylon, J.; Qi, X.; Sheng, K.; Low, D. A.; Kupelian, P.; Santhanam, A.; Staton, R.; Pukala, J.; Manon, R.

2015-01-01

be caused by the biomechanical deformation process. Accuracy and stability of the model response were validated using ground-truth simulations representing soft tissue behavior under local and global deformations. Numerical accuracy of the HN deformations was analyzed by applying nonrigid skeletal transformations acquired from interfraction kVCT images to the model’s skeletal structures and comparing the subsequent soft tissue deformations of the model with the clinical anatomy. Results: The GPU based framework enabled the model deformation to be performed at 60 frames/s, facilitating simulations of posture changes and physiological regressions at interactive speeds. The soft tissue response was accurate with a R 2 value of >0.98 when compared to ground-truth global and local force deformation analysis. The deformation of the HN anatomy by the model agreed with the clinically observed deformations with an average correlation coefficient of 0.956. For a clinically relevant range of posture and physiological changes, the model deformations stabilized with an uncertainty of less than 0.01 mm. Conclusions: Documenting dose delivery for HN radiotherapy is essential accounting for posture and physiological changes. The biomechanical model discussed in this paper was able to deform in real-time, allowing interactive simulations and visualization of such changes. The model would allow patient specific validations of the DIR method and has the potential to be a significant aid in adaptive radiotherapy techniques

Deformation microstructures

DEFF Research Database (Denmark)

Hansen, N.; Huang, X.; Hughes, D.A.

2004-01-01

Microstructural characterization and modeling has shown that a variety of metals deformed by different thermomechanical processes follows a general path of grain subdivision, by dislocation boundaries and high angle boundaries. This subdivision has been observed to very small structural scales...... of the order of 10 nm, produced by deformation under large sliding loads. Limits to the evolution of microstructural parameters during monotonic loading have been investigated based on a characterization by transmission electron microscopy. Such limits have been observed at an equivalent strain of about 10...

Deformation Behavior of Sub-micron and Micron Sized Alumina Particles in Compression.

Energy Technology Data Exchange (ETDEWEB)

Sarobol, Pylin; Chandross, Michael E.; Carroll, Jay; Mook, William; Boyce, Brad; Kotula, Paul Gabriel; McKenzie, Bonnie Beth; Bufford, Daniel Charles; Hall, Aaron Christopher.

2014-09-01

significant plastic deformation during compressi on . On the other hand, the micron sized Al 2 O 3 particles exhibited brittle f racture in compression. In situ compression experiments showed 3um Al 2 O 3 particles fractured into pieces without observable plastic deformation in compression. Particle deformation behaviors will be used to inform Al 2 O 3 coating deposition parameters and particle - particle bonding in the consolidated Al 2 O 3 coatings.

Hand washing promotion for preventing diarrhoea.

Science.gov (United States)

Ejemot-Nwadiaro, Regina I; Ehiri, John E; Arikpo, Dachi; Meremikwu, Martin M; Critchley, Julia A

2015-09-03

Diarrhoea accounts for 1.8 million deaths in children in low- and middle-income countries (LMICs). One of the identified strategies to prevent diarrhoea is hand washing. To assess the effects of hand washing promotion interventions on diarrhoeal episodes in children and adults. We searched the Cochrane Infectious Diseases Group Specialized Register (27 May 2015); CENTRAL (published in the Cochrane Library 2015, Issue 5); MEDLINE (1966 to 27 May 2015); EMBASE (1974 to 27 May 2015); LILACS (1982 to 27 May 2015); PsycINFO (1967 to 27 May 2015); Science Citation Index and Social Science Citation Index (1981 to 27 May 2015); ERIC (1966 to 27 May 2015); SPECTR (2000 to 27 May 2015); Bibliomap (1990 to 27 May 2015); RoRe, The Grey Literature (2002 to 27 May 2015); World Health Organization (WHO) International Clinical Trial Registry Platform (ICTRP), metaRegister of Controlled Trials (mRCT), and reference lists of articles up to 27 May 2015. We also contacted researchers and organizations in the field. Individually randomized controlled trials (RCTs) and cluster-RCTs that compared the effects of hand washing interventions on diarrhoea episodes in children and adults with no intervention. Three review authors independently assessed trial eligibility, extracted data, and assessed risk of bias. We stratified the analyses for child day-care centres or schools, community, and hospital-based settings. Where appropriate, incidence rate ratios (IRR) were pooled using the generic inverse variance method and random-effects model with 95% confidence intervals (CIs). We used the GRADE approach to assess the quality of evidence. We included 22 RCTs: 12 trials from child day-care centres or schools in mainly high-income countries (54,006 participants), nine community-based trials in LMICs (15,303 participants), and one hospital-based trial among people with acquired immune deficiency syndrome (AIDS) (148 participants).Hand washing promotion (education activities, sometimes with

SU-F-BRF-10: Deformable MRI to CT Validation Employing Same Day Planning MRI for Surrogate Analysis

Energy Technology Data Exchange (ETDEWEB)

Padgett, K; Stoyanova, R; Johnson, P; Dogan, N; Pollack, A [University of Miami School of Medicine, Miami, FL (United States); Piper, J; Javorek, A [MIM Software, Inc., Beachwood, OH (United States)

2014-06-15

Purpose: To compare rigid and deformable registrations of the prostate in the multi-modality setting (diagnostic-MRI to planning-CT) by utilizing a planning-MRI as a surrogate. The surrogate allows for the direct quantitative analysis which can be difficult in the multi-modality domain where intensity mapping differs. Methods: For ten subjects, T2 fast-spin-echo images were acquired at two different time points, the first several weeks prior to planning (diagnostic-MRI) and the second on the same day in which the planning CT was collected (planning-MRI). Significant effort in patient positioning and bowel/bladder preparation was undertaken to minimize distortion of the prostate in all datasets. The diagnostic-MRI was deformed to the planning-CT utilizing a commercially available deformable registration algorithm synthesized from local registrations. The deformed MRI was then rigidly aligned to the planning MRI which was used as the surrogate for the planning-CT. Agreement between the two MRI datasets was scored using intensity based metrics including Pearson correlation and normalized mutual information, NMI. A local analysis was performed by looking only within the prostate, proximal seminal vesicles, penile bulb and combined areas. A similar method was used to assess a rigid registration between the diagnostic-MRI and planning-CT. Results: Utilizing the NMI, the deformable registrations were superior to the rigid registrations in 9 of 10 cases demonstrating a 15.94% improvement (p-value < 0.001) within the combined area. The Pearson correlation showed similar results with the deformable registration superior in the same number of cases and demonstrating a 6.97% improvement (p-value <0.011). Conclusion: Validating deformable multi-modality registrations using spatial intensity based metrics is difficult due to the inherent differences in intensity mapping. This population provides an ideal testing ground for MRI to CT deformable registrations by obviating the need

Community-acquired bacterial meningitis

NARCIS (Netherlands)

van de Beek, Diederik; Brouwer, Matthijs; Hasbun, Rodrigo; Koedel, Uwe; Whitney, Cynthia G.; Wijdicks, Eelco

2016-01-01

Meningitis is an inflammation of the meninges and subarachnoid space that can also involve the brain cortex and parenchyma. It can be acquired spontaneously in the community - community-acquired bacterial meningitis - or in the hospital as a complication of invasive procedures or head trauma

Hand Hygiene With Alcohol-Based Hand Rub: How Long Is Long Enough?

Science.gov (United States)

Pires, Daniela; Soule, Hervé; Bellissimo-Rodrigues, Fernando; Gayet-Ageron, Angèle; Pittet, Didier

2017-05-01

BACKGROUND Hand hygiene is the core element of infection prevention and control. The optimal hand-hygiene gesture, however, remains poorly defined. OBJECTIVE We aimed to evaluate the influence of hand-rubbing duration on the reduction of bacterial counts on the hands of healthcare personnel (HCP). METHODS We performed an experimental study based on the European Norm 1500. Hand rubbing was performed for 10, 15, 20, 30, 45, or 60 seconds, according to the WHO technique using 3 mL alcohol-based hand rub. Hand contamination with E. coli ATCC 10536 was followed by hand rubbing and sampling. A generalized linear mixed model with a random effect on the subject adjusted for hand size and gender was used to analyze the reduction in bacterial counts after each hand-rubbing action. In addition, hand-rubbing durations of 15 and 30 seconds were compared to assert non-inferiority (0.6 log10). RESULTS In total, 32 HCP performed 123 trials. All durations of hand rubbing led to significant reductions in bacterial counts (Phand rubbing were not significantly different from those obtained after 30 seconds. The mean bacterial reduction after 15 seconds of hand rubbing was 0.11 log10 lower (95% CI, -0.46 to 0.24) than after 30 seconds, demonstrating non-inferiority. CONCLUSIONS Hand rubbing for 15 seconds was not inferior to 30 seconds in reducing bacterial counts on hands under the described experimental conditions. There was no gain in reducing bacterial counts from hand rubbing longer than 30 seconds. Further studies are needed to assess the clinical significance of our findings. Infect Control Hosp Epidemiol 2017;38:547-552.

Post-Eruption Deformation Processes Measured Using ALOS-1 and UAVSAR InSAR at Pacaya Volcano, Guatemala

Directory of Open Access Journals (Sweden)

Lauren N. Schaefer

2016-01-01

Full Text Available Pacaya volcano is a persistently active basaltic cone complex located in the Central American Volcanic Arc in Guatemala. In May of 2010, violent Volcanic Explosivity Index-3 (VEI-3 eruptions caused significant topographic changes to the edifice, including a linear collapse feature 600 m long originating from the summit, the dispersion of ~20 cm of tephra and ash on the cone, the emplacement of a 5.4 km long lava flow, and ~3 m of co-eruptive movement of the southwest flank. For this study, Interferometric Synthetic Aperture Radar (InSAR images (interferograms processed from both spaceborne Advanced Land Observing Satellite-1 (ALOS-1 and aerial Uninhabited Aerial Vehicle Synthetic Aperture Radar (UAVSAR data acquired between 31 May 2010 and 10 April 2014 were used to measure post-eruptive deformation events. Interferograms suggest three distinct deformation processes after the May 2010 eruptions, including: (1 subsidence of the area involved in the co-eruptive slope movement; (2 localized deformation near the summit; and (3 emplacement and subsequent subsidence of about a 5.4 km lava flow. The detection of several different geophysical signals emphasizes the utility of measuring volcanic deformation using remote sensing techniques with broad spatial coverage. Additionally, the high spatial resolution of UAVSAR has proven to be an excellent compliment to satellite data, particularly for constraining motion components. Measuring the rapid initiation and cessation of flank instability, followed by stabilization and subsequent influence on eruptive features, provides a rare glimpse into volcanic slope stability processes. Observing these and other deformation events contributes both to hazard assessment at Pacaya and to the study of the stability of stratovolcanoes.

Acquired Methemoglobinaemia

Directory of Open Access Journals (Sweden)

Adil Al-Lawati

2012-05-01

Full Text Available Acquired methemoglobinaemia is a relatively rare condition and, therefore infrequently encountered in acute medical practice. Suspicion of the condition may be triggered when the measured PaO2 is ‘out of keeping’ with the oxygen saturations that are discovered with pulse oximetry. We describe two separate cases of acquired methemoglobinaemia secondary to the recreational use of alkyl nitrites (’poppers’. The patients presented at separate times to two different teaching hospitals in London, UK. The similarity of these cases has led the authors to conclude that a raised awareness of this potentially fatal condition, and its association with a widely-available recreational drug, is necessary to ensure a correct and timely diagnosis.

Long-term deformation analysis of historical buildings through the advanced SBAS-DInSAR technique: the case study of the city of Rome, Italy

International Nuclear Information System (INIS)

Zeni, G; Bonano, M; Casu, F; Manunta, M; Manzo, M; Pepe, A; Lanari, R; Marsella, M

2011-01-01

Monitoring of deformation phenomena affecting urban areas and man-made structures is of key relevance for the preservation of the artistic, archaeological and architectural heritage. The differential SAR interferometry (DInSAR) technique has already been demonstrated to be an effective tool for non-invasive deformation analyses over large areas by producing spatially dense deformation maps with centimetre to millimetre accuracy. Moreover, by exploiting long sequences of SAR data acquired by different sensors, the advanced DInSAR technique referred to as the small baseline subset (SBAS) approach allows providing long-term deformation time series, which are strategic for guaranteeing the monitoring of urban area displacements. In this work, we investigate the effectiveness of the two-scale multi-sensor SBAS-DInSAR approach to detect and monitor displacements affecting historical and artistic monuments. The presented results, achieved by applying the full resolution SBAS technique to a huge set of ERS-1/2 and ENVISAT data, spanning the 1992–2010 time interval and relevant to the city of Rome (Italy), show the capability of this approach to detect and analyse the temporal evolution of possible deformation phenomena affecting historical buildings and archaeological sites. Accordingly, our analysis demonstrates the effectiveness of the full resolution multi-sensor SBAS approach to operate as a surface deformation tool for supporting the study and conservation strategies of the historical, cultural and artistic heritage

q-Deformed nonlinear maps

Indian Academy of Sciences (India)

Home; Journals; Pramana – Journal of Physics; Volume 64; Issue 3 ... Keywords. Nonlinear dynamics; logistic map; -deformation; Tsallis statistics. ... As a specific example, a -deformation procedure is applied to the logistic map. Compared ...

Dynamic magnetic resonance angiography of the arteries of the hand. A comparison between an extracellular and an intravascular contrast agent

International Nuclear Information System (INIS)

Reisinger, Clemens; Gluecker, Thomas; Jacob, Augustinus Ludwig; Bongartz, Georg; Bilecen, Deniz

2009-01-01

The purpose of this study was to compare the image quality of the intravascular contrast agent gadofosveset with the extracellular contrast agent gadoterate meglumine in time-resolved three-dimensional magnetic resonance (MR) angiography of the human arteries of the hand. The value of cuff compression technique for suppression of venous enhancement for both contrast agents was also investigated. Three-dimensional MR angiograms of both hands of 11 healthy volunteers were acquired for each contrast agent at 1.5-T, while subsystolic cuff compression was applied at one side. Quantitative and qualitative evaluation were performed and analyzed with Student's t-test. Visualization of vessels was superior in the images acquired with gadofosveset, especially in the late phases. Quantitative and qualitative evaluation showed significantly higher values for gadofosveset. The cuff compression at the lower arm proved to be an effective method to enhance arterial vessels. In conclusion the blood pool agent gadofosveset is superior for the dynamic imaging of the vessels of the hand when compared with the extracellular contrast agent gadoterate meglumine. To fully utilize the advantages of intravascular contrast agents, venous overlay has to be delayed or reduced, which can be achieved effectively by subsystolic lower arm cuff compression. (orig.)

Hand in Hand - SEI Programmes for School Staff

DEFF Research Database (Denmark)

Nielsen, Birgitte Lund; Réol, Lise Andersen; Laursen, Hilmar Dyrborg

2017-01-01

This catalogue of research in the field of SEI programmes for the school staff’s and teachers’ SEI competencies is based on a review performed by the main researchers Birgitte Lund Nielsen, Lise Andersen Réol and Hilmar Dyrborg Laursen, VIA University College, Denmark, but discussed by the entire...... team of Hand in Hand partner countries and researchers. The aim was to identify the central aspects and elements concerning successful implementation, and school staff’s development of professional competencies in the specific field of supporting students’ social, emotional and intercultural (SEI......) competencies. Abstract: Framed by the EU-project Hand in Hand focusing on Social, Emotional and Intercultural (SEI) competencies among students and school staff, the paper discusses implementation and professional competencies based on a research review. The following five topics were identified: 1...

Measurement of Seafloor Deformation in the Marine Sector of the Campi Flegrei Caldera (Italy)

Science.gov (United States)

Iannaccone, Giovanni; Guardato, Sergio; Donnarumma, Gian Paolo; De Martino, Prospero; Dolce, Mario; Macedonio, Giovanni; Chierici, Francesco; Beranzoli, Laura

2018-01-01

We present an assessment of vertical seafloor deformation in the shallow marine sector of the Campi Flegrei caldera (southern Italy) obtained from GPS and bottom pressure recorder (BPR) data, acquired over the period April 2016 to July 2017 in the Gulf of Pozzuoli by a new marine infrastructure, MEDUSA. This infrastructure consists of four fixed buoys with GPS receivers; each buoy is connected by cable to a seafloor multisensor module hosting a BPR. The measured maximum vertical uplift of the seafloor is about 4.2 ± 0.4 cm. The MEDUSA data were then compared to the expected vertical displacement in the marine sector according to a Mogi model point source computed using only GPS land measurements. The results show that a single point source model of deformation is able to explain both the GPS land and seafloor data. Moreover, we demonstrate that a network of permanent GPS buoys represents a powerful tool to measure the seafloor vertical deformation field in shallow water. The performance of this system is comparable to on-land high-precision GPS networks, marking a significant achievement and advance in seafloor geodesy and extending volcano monitoring capabilities to shallow offshore areas (up to 100 m depth). The GPS measurements of MEDUSA have also been used to confirm that the BPR data provide an independent measure of the seafloor vertical uplift in shallow water.

Unsteady hydrodynamic forces acting on a hand and its flow field during sculling motion.

Science.gov (United States)

Takagi, Hideki; Shimada, Shohei; Miwa, Takahiro; Kudo, Shigetada; Sanders, Ross; Matsuuchi, Kazuo

2014-12-01

The goal of this research is to clarify the mechanism by which unsteady forces are generated during sculling by a skilled swimmer and thereby to contribute to improving propulsive techniques. We used particle image velocimetry (PIV) to acquire data on the kinematics of the hand during sculling, such as fluid forces and flow field. By investigating the correlations between these data, we expected to find a new propulsion mechanism. The experiment was performed in a flow-controlled water channel. The participant executed sculling motions to remain at a fixed position despite constant water flow. PIV was used to visualize the flow-field cross-section in the plane of hand motion. Moreover, the fluid forces acting on the hand were estimated from pressure distribution measurements performed on the hand and simultaneous three-dimensional motion analysis. By executing the sculling motion, a skilled swimmer produces large unsteady fluid forces when the leading-edge vortex occurs on the dorsal side of the hand and wake capture occurs on the palm side. By using a new approach, we observed interesting unsteady fluid phenomena similar to those of flying insects. The study indicates that it is essential for swimmers to fully exploit vortices. A better understanding of these phenomena might lead to an improvement in sculling techniques. Copyright © 2014 Elsevier B.V. All rights reserved.

MEASUREMENT OF LARGE-SCALE SOLAR POWER PLANT BY USING IMAGES ACQUIRED BY NON-METRIC DIGITAL CAMERA ON BOARD UAV

Directory of Open Access Journals (Sweden)

R. Matsuoka

2012-07-01

Full Text Available This paper reports an experiment conducted in order to investigate the feasibility of the deformation measurement of a large-scale solar power plant on reclaimed land by using images acquired by a non-metric digital camera on board a micro unmanned aerial vehicle (UAV. It is required that a root mean squares of errors (RMSE in height measurement should be less than 26 mm that is 1/3 of the critical limit of deformation of 78 mm off the plane of a solar panel. Images utilized in the experiment have been obtained by an Olympus PEN E-P2 digital camera on board a Microdrones md4-1000 quadrocopter. The planned forward and side overlap ratios of vertical image acquisition have been 60 % and 60 % respectively. The planned flying height of the UAV has been 20 m above the ground level and the ground resolution of an image is approximately 5.0 mm by 5.0 mm. 8 control points around the experiment area are utilized for orientation. Measurement results are evaluated by the space coordinates of 220 check points which are corner points of 55 solar panels selected from 1768 solar panels in the experiment area. Two teams engage in the experiment. One carries out orientation and measurement by using 171 images following the procedure of conventional aerial photogrammetry, and the other executes those by using 126 images in the manner of close range photogrammetry. The former fails to satisfy the required accuracy, while the RMSE in height measurement by the latter is 8.7 mm that satisfies the required accuracy. From the experiment results, we conclude that the deformation measurement of a large-scale solar power plant on reclaimed land by using images acquired by a nonmetric digital camera on board a micro UAV would be feasible if points utilized in orientation and measurement have a sufficient number of bundles in good geometry and self-calibration in orientation is carried out.

Laboratory-acquired brucellosis

DEFF Research Database (Denmark)

Fabiansen, C.; Knudsen, J.D.; Lebech, A.M.

2008-01-01

Brucellosis is a rare disease in Denmark. We describe one case of laboratory-acquired brucellosis from an index patient to a laboratory technician following exposure to an infected blood culture in a clinical microbiology laboratory Udgivelsesdato: 2008/6/9......Brucellosis is a rare disease in Denmark. We describe one case of laboratory-acquired brucellosis from an index patient to a laboratory technician following exposure to an infected blood culture in a clinical microbiology laboratory Udgivelsesdato: 2008/6/9...

Fully embedded myoelectric control for a wearable robotic hand orthosis.

Science.gov (United States)

Ryser, Franziska; Butzer, Tobias; Held, Jeremia P; Lambercy, Olivier; Gassert, Roger

2017-07-01

To prevent learned non-use of the affected hand in chronic stroke survivors, rehabilitative training should be continued after discharge from the hospital. Robotic hand orthoses are a promising approach for home rehabilitation. When combined with intuitive control based on electromyography, the therapy outcome can be improved. However, such systems often require extensive cabling, experience in electrode placement and connection to external computers. This paper presents the framework for a stand-alone, fully wearable and real-time myoelectric intention detection system based on the Myo armband. The hard and software for real-time gesture classification were developed and combined with a routine to train and customize the classifier, leading to a unique ease of use. The system including training of the classifier can be set up within less than one minute. Results demonstrated that: (1) the proposed algorithm can classify five gestures with an accuracy of 98%, (2) the final system can online classify three gestures with an accuracy of 94.3% and, in a preliminary test, (3) classify three gestures from data acquired from mildly to severely impaired stroke survivors with an accuracy of over 78.8%. These results highlight the potential of the presented system for electromyography-based intention detection for stroke survivors and, with the integration of the system into a robotic hand orthosis, the potential for a wearable platform for all day robot-assisted home rehabilitation.

Linear and nonlinear subspace analysis of hand movements during grasping.

Science.gov (United States)

Cui, Phil Hengjun; Visell, Yon

2014-01-01

This study investigated nonlinear patterns of coordination, or synergies, underlying whole-hand grasping kinematics. Prior research has shed considerable light on roles played by such coordinated degrees-of-freedom (DOF), illuminating how motor control is facilitated by structural and functional specializations in the brain, peripheral nervous system, and musculoskeletal system. However, existing analyses suppose that the patterns of coordination can be captured by means of linear analyses, as linear combinations of nominally independent DOF. In contrast, hand kinematics is itself highly nonlinear in nature. To address this discrepancy, we sought to to determine whether nonlinear synergies might serve to more accurately and efficiently explain human grasping kinematics than is possible with linear analyses. We analyzed motion capture data acquired from the hands of individuals as they grasped an array of common objects, using four of the most widely used linear and nonlinear dimensionality reduction algorithms. We compared the results using a recently developed algorithm-agnostic quality measure, which enabled us to assess the quality of the dimensional reductions that resulted by assessing the extent to which local neighborhood information in the data was preserved. Although qualitative inspection of this data suggested that nonlinear correlations between kinematic variables were present, we found that linear modeling, in the form of Principle Components Analysis, could perform better than any of the nonlinear techniques we applied.

Hand washing promotion for preventing diarrhoea

Science.gov (United States)

Ejemot-Nwadiaro, Regina I; Ehiri, John E; Arikpo, Dachi; Meremikwu, Martin M; Critchley, Julia A

2015-01-01

Background Diarrhoea accounts for 1.8 million deaths in children in low- and middle-income countries (LMICs). One of the identified strategies to prevent diarrhoea is hand washing. Objectives To assess the effects of hand washing promotion interventions on diarrhoeal episodes in children and adults. Search methods We searched the Cochrane Infectious Diseases Group Specialized Register (27 May 2015); CENTRAL (published in the Cochrane Library 2015, Issue 5); MEDLINE (1966 to 27 May 2015); EMBASE (1974 to 27 May 2015); LILACS (1982 to 27 May 2015); PsycINFO (1967 to 27 May 2015); Science Citation Index and Social Science Citation Index (1981 to 27 May 2015); ERIC (1966 to 27 May 2015); SPECTR (2000 to 27 May 2015); Bibliomap (1990 to 27 May 2015); RoRe, The Grey Literature (2002 to 27 May 2015); World Health Organization (WHO) International Clinical Trial Registry Platform (ICTRP), metaRegister of Controlled Trials (mRCT), and reference lists of articles up to 27 May 2015. We also contacted researchers and organizations in the field. Selection criteria Individually randomized controlled trials (RCTs) and cluster-RCTs that compared the effects of hand washing interventions on diarrhoea episodes in children and adults with no intervention. Data collection and analysis Three review authors independently assessed trial eligibility, extracted data, and assessed risk of bias. We stratified the analyses for child day-care centres or schools, community, and hospital-based settings. Where appropriate, incidence rate ratios (IRR) were pooled using the generic inverse variance method and random-effects model with 95% confidence intervals (CIs). We used the GRADE approach to assess the quality of evidence. Main results We included 22 RCTs: 12 trials from child day-care centres or schools in mainly high-income countries (54,006 participants), nine community-based trials in LMICs (15,303 participants), and one hospital-based trial among people with acquired immune deficiency

Deformation twinning: Influence of strain rate

Energy Technology Data Exchange (ETDEWEB)

Gray, G.T. III

1993-11-01

Twins in most crystal structures, including advanced materials such as intermetallics, form more readily as the temperature of deformation is decreased or the rate of deformation is increased. Both parameters lead to the suppression of thermally-activated dislocation processes which can result in stresses high enough to nucleate and grow deformation twins. Under high-strain rate or shock-loading/impact conditions deformation twinning is observed to be promoted even in high stacking fault energy FCC metals and alloys, composites, and ordered intermetallics which normally do not readily deform via twinning. Under such conditions and in particular under the extreme loading rates typical of shock wave deformation the competition between slip and deformation twinning can be examined in detail. In this paper, examples of deformation twinning in the intermetallics TiAl, Ti-48Al-lV and Ni{sub 3}A as well in the cermet Al-B{sub 4}C as a function of strain rate will be presented. Discussion includes: (1) the microstructural and experimental variables influencing twin formation in these systems and twinning topics related to high-strain-rate loading, (2) the high velocity of twin formation, and (3) the influence of deformation twinning on the constitutive response of advanced materials.

Deformation of Man Made Objects

KAUST Repository

Ibrahim, Mohamed

2012-07-01

We introduce a framework for 3D object deformation with primary focus on man-made objects. Our framework enables a user to deform a model while preserving its defining characteristics. Moreover, our framework enables a user to set constraints on a model to keep its most significant features intact after the deformation process. Our framework supports a semi-automatic constraint setting environment, where some constraints could be automatically set by the framework while others are left for the user to specify. Our framework has several advantages over some state of the art deformation techniques in that it enables a user to add new features to the deformed model while keeping its general look similar to the input model. In addition, our framework enables the rotation and extrusion of different parts of a model.

Guideline Implementation: Hand Hygiene.

Science.gov (United States)

Goldberg, Judith L

2017-02-01

Performing proper hand hygiene and surgical hand antisepsis is essential to reducing the rates of health care-associated infections, including surgical site infections. The updated AORN "Guideline for hand hygiene" provides guidance on hand hygiene and surgical hand antisepsis, the wearing of fingernail polish and artificial nails, proper skin care to prevent dermatitis, the wearing of jewelry, hand hygiene product selection, and quality assurance and performance improvement considerations. This article focuses on key points of the guideline to help perioperative personnel make informed decisions about hand hygiene and surgical hand antisepsis. The key points address the necessity of keeping fingernails and skin healthy, not wearing jewelry on the hands or wrists in the perioperative area, properly performing hand hygiene and surgical hand antisepsis, and involving patients and visitors in hand hygiene initiatives. Perioperative RNs should review the complete guideline for additional information and for guidance when writing and updating policies and procedures. Copyright © 2017 AORN, Inc. Published by Elsevier Inc. All rights reserved.

q-deformations of noncompact Lie (super-) algebras: The examples of q-deformed Lorentz, Weyl, Poincare' and (super-) conformal algebras

International Nuclear Information System (INIS)

Dobrev, V.K.

1992-01-01

We review and explain a canonical procedure for the q-deformation of the real forms G of complex Lie (super-) algebras associated with (generalized) Cartan matrices. Our procedure gives different q-deformations for the non-conjugate Cartan subalgebras of G. We give several in detail the q-deformed Lorentz and conformal (super-) algebras. The q-deformed conformal algebra contains as a subalgebra a q-deformed Poincare algebra and as Hopf subalgebras two conjugate 11-generator q-deformed Weyl algebras. The q-deformed Lorentz algebra in Hopf subalgebra of both Weyl algebras. (author). 24 refs

Formalization of informally acquired competences as part of academic certificate programs in healthcare – “prototype” of a model / Formalisierung informell erworbener Kompetenzen im Rahmen akademischer Zertifikatsprogramme im Gesundheitsbereich – „Prototyp“ eines Modells

Directory of Open Access Journals (Sweden)

Wolf Alexander Karsten

2016-05-01

Full Text Available The health care sector is facing many aspects of transformation. One aspect amongst others herein is an alteration of qualification profiles. Universities have to focus on both aspects determining future qualification profiles and increasing permeability between educational systems in a sense of optimally intermeshing competences that have been acquired at universities and those that have been acquired outside of them. This leads to the question how to create university certificate programs that offers two aspects: academic qualification on the one hand and on the other hand a possibility to identify, evaluate and certify non-formally and informally acquired competences of participating students. The ultimate goal is to identify and evaluate a person´s overall competence in a clearly defined thematic context, whereat competences that have been acquired outside universities will play an important role. Competences that have been certified by these academic programs may be used later for crediting purposes. In this report an initial prototype is being presented. It defines itself mainly as additional novel way of discussing crediting concepts.

Inspections of Hand Washing Supplies and Hand Sanitizer in Public Schools

Science.gov (United States)

Ramos, Mary M.; Blea, Mary; Trujillo, Rebecca; Greenberg, Cynthia

2010-01-01

Hand washing and hand antisepsis are proven infection control measures in the school setting, yet barriers such as lack of soap, paper towels, and hand sanitizer can hinder compliance. This pilot study measured the prevalence of hand cleaning supplies in public schools. Ten school districts (93 schools) participated in school nurse inspections. In…

A virtual phantom library for the quantification of deformable image registration uncertainties in patients with cancers of the head and neck.

Science.gov (United States)

Pukala, Jason; Meeks, Sanford L; Staton, Robert J; Bova, Frank J; Mañon, Rafael R; Langen, Katja M

2013-11-01

Deformable image registration (DIR) is being used increasingly in various clinical applications. However, the underlying uncertainties of DIR are not well-understood and a comprehensive methodology has not been developed for assessing a range of interfraction anatomic changes during head and neck cancer radiotherapy. This study describes the development of a library of clinically relevant virtual phantoms for the purpose of aiding clinicians in the QA of DIR software. These phantoms will also be available to the community for the independent study and comparison of other DIR algorithms and processes. Each phantom was derived from a pair of kVCT volumetric image sets. The first images were acquired of head and neck cancer patients prior to the start-of-treatment and the second were acquired near the end-of-treatment. A research algorithm was used to autosegment and deform the start-of-treatment (SOT) images according to a biomechanical model. This algorithm allowed the user to adjust the head position, mandible position, and weight loss in the neck region of the SOT images to resemble the end-of-treatment (EOT) images. A human-guided thin-plate splines algorithm was then used to iteratively apply further deformations to the images with the objective of matching the EOT anatomy as closely as possible. The deformations from each algorithm were combined into a single deformation vector field (DVF) and a simulated end-of-treatment (SEOT) image dataset was generated from that DVF. Artificial noise was added to the SEOT images and these images, along with the original SOT images, created a virtual phantom where the underlying "ground-truth" DVF is known. Images from ten patients were deformed in this fashion to create ten clinically relevant virtual phantoms. The virtual phantoms were evaluated to identify unrealistic DVFs using the normalized cross correlation (NCC) and the determinant of the Jacobian matrix. A commercial deformation algorithm was applied to the virtual

Effect of hand sanitizer location on hand hygiene compliance.

Science.gov (United States)

Cure, Laila; Van Enk, Richard

2015-09-01

Hand hygiene is the most important intervention to prevent infection in hospitals. Health care workers should clean their hands at least before and after contact with patients. Hand sanitizer dispensers are important to support hand hygiene because they can be made available throughout hospital units. The aim of this study was to determine whether the usability of sanitizer dispensers correlates with compliance of staff in using the sanitizer in a hospital. This study took place in a Midwest, 404-bed, private, nonprofit community hospital with 15 inpatient care units in addition to several ambulatory units. The usability and standardization of sanitizers in 12 participating inpatient units were evaluated. The hospital measured compliance of staff with hand hygiene as part of their quality improvement program. Data from 2010-2012 were analyzed to measure the relationship between compliance and usability using mixed-effects logistic regression models. The total usability score (P = .0046), visibility (P = .003), and accessibility of the sanitizer on entrance to the patient room (P = .00055) were statistically associated with higher observed compliance rates. Standardization alone showed no significant impact on observed compliance (P = .37). Hand hygiene compliance can be influenced by visibility and accessibility of dispensers. The sanitizer location should be part of multifaceted interventions to improve hand hygiene. Copyright © 2015 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Elsevier Inc. All rights reserved.

InSAR Deformation Time Series Processed On-Demand in the Cloud

Science.gov (United States)

Horn, W. B.; Weeden, R.; Dimarchi, H.; Arko, S. A.; Hogenson, K.

2017-12-01

During this past year, ASF has developed a cloud-based on-demand processing system known as HyP3 (http://hyp3.asf.alaska.edu/), the Hybrid Pluggable Processing Pipeline, for Synthetic Aperture Radar (SAR) data. The system makes it easy for a user who doesn't have the time or inclination to install and use complex SAR processing software to leverage SAR data in their research or operations. One such processing algorithm is generation of a deformation time series product, which is a series of images representing ground displacements over time, which can be computed using a time series of interferometric SAR (InSAR) products. The set of software tools necessary to generate this useful product are difficult to install, configure, and use. Moreover, for a long time series with many images, the processing of just the interferograms can take days. Principally built by three undergraduate students at the ASF DAAC, the deformation time series processing relies the new Amazon Batch service, which enables processing of jobs with complex interconnected dependencies in a straightforward and efficient manner. In the case of generating a deformation time series product from a stack of single-look complex SAR images, the system uses Batch to serialize the up-front processing, interferogram generation, optional tropospheric correction, and deformation time series generation. The most time consuming portion is the interferogram generation, because even for a fairly small stack of images many interferograms need to be processed. By using AWS Batch, the interferograms are all generated in parallel; the entire process completes in hours rather than days. Additionally, the individual interferograms are saved in Amazon's cloud storage, so that when new data is acquired in the stack, an updated time series product can be generated with minimal addiitonal processing. This presentation will focus on the development techniques and enabling technologies that were used in developing the time

Multi-stage 3D-2D registration for correction of anatomical deformation in image-guided spine surgery

Science.gov (United States)

Ketcha, M. D.; De Silva, T.; Uneri, A.; Jacobson, M. W.; Goerres, J.; Kleinszig, G.; Vogt, S.; Wolinsky, J.-P.; Siewerdsen, J. H.

2017-06-01

A multi-stage image-based 3D-2D registration method is presented that maps annotations in a 3D image (e.g. point labels annotating individual vertebrae in preoperative CT) to an intraoperative radiograph in which the patient has undergone non-rigid anatomical deformation due to changes in patient positioning or due to the intervention itself. The proposed method (termed msLevelCheck) extends a previous rigid registration solution (LevelCheck) to provide an accurate mapping of vertebral labels in the presence of spinal deformation. The method employs a multi-stage series of rigid 3D-2D registrations performed on sets of automatically determined and increasingly localized sub-images, with the final stage achieving a rigid mapping for each label to yield a locally rigid yet globally deformable solution. The method was evaluated first in a phantom study in which a CT image of the spine was acquired followed by a series of 7 mobile radiographs with increasing degree of deformation applied. Second, the method was validated using a clinical data set of patients exhibiting strong spinal deformation during thoracolumbar spine surgery. Registration accuracy was assessed using projection distance error (PDE) and failure rate (PDE  >  20 mm—i.e. label registered outside vertebra). The msLevelCheck method was able to register all vertebrae accurately for all cases of deformation in the phantom study, improving the maximum PDE of the rigid method from 22.4 mm to 3.9 mm. The clinical study demonstrated the feasibility of the approach in real patient data by accurately registering all vertebral labels in each case, eliminating all instances of failure encountered in the conventional rigid method. The multi-stage approach demonstrated accurate mapping of vertebral labels in the presence of strong spinal deformation. The msLevelCheck method maintains other advantageous aspects of the original LevelCheck method (e.g. compatibility with standard clinical workflow, large

Die Sprache der Hande zu den Handen sprechen (Talking the Language of the Hands to the Hands). DB-LINK.

Science.gov (United States)

Miles, Barbara

This paper examines the importance of hands for the person who is deafblind, reviews hand development, and identifies specific teaching skills that facilitate hand development and expressiveness in persons who are deafblind. It notes that the hands of a deafblind individual serve not only as tools but also as sense organs (to compensate for their…

The use of the analytic hierarchy process to aid decision making in acquired equinovarus deformity.

Science.gov (United States)

van Til, Janine A; Renzenbrink, Gerbert J; Dolan, James G; Ijzerman, Maarten J

2008-03-01

To increase the transparency of decision making about treatment in patients with equinovarus deformity poststroke. The analytic hierarchy process (AHP) was used as a structured methodology to study the subjective rationale behind choice of treatment. An 8-hour meeting at a centrally located rehabilitation center in The Netherlands, during which a patient video was shown to all participants (using a personal computer and a large screen) and the patient details were provided on paper. A panel of 10 health professionals from different backgrounds. Not applicable. The performance of the applicable treatments on outcome, impact, comfort, cosmetics, daily effort, and risks and side effects of treatment, as well as the relative importance of criteria in the choice of treatment. According to the model, soft-tissue surgery (.413) ranked first as the preferred treatment, followed by orthopedic footwear (.181), ankle-foot orthosis (.147), surface electrostimulation (.137), and finally implanted electrostimulation (.123). Outcome was the most influential consideration affecting treatment choice (.509), followed by risk and side effects (.194), comfort (.104), daily effort (.098), cosmetics (.065), and impact of treatment (.030). Soft-tissue surgery was judged best on outcome, daily effort, comfortable shoe wear, and cosmetically acceptable result and was thereby preferred as a treatment alternative by the panel in this study. In contrast, orthosis and orthopedic footwear are usually preferred in daily practice. The AHP method was found to be suitable methodology for eliciting subjective opinions and quantitatively comparing treatments in the absence of scientific evidence.

Hand hygiene strategies

OpenAIRE

Yazaji, Eskandar Alex

2011-01-01

Hand hygiene is one of the major players in preventing healthcare associated infections. However, healthcare workers compliance with hand hygiene continues to be a challenge. This article will address strategies to help improving hand hygiene compliance. Keywords: hand hygiene; healthcare associated infections; multidisciplinary program; system change; accountability; education; feedback(Published: 18 July 2011)Citation: Journal of Community Hospital Internal Medicine Perspectives 2011, 1: 72...

Adherence to hand hygiene protocol by clinicians and medical students at Queen Elizabeth Central Hospital, Blantyre-Malawi.

Science.gov (United States)

Kalata, N L; Kamange, L; Muula, A S

2013-06-01

While communicable diseases are the leading causes of morbidity and mortality in Malawi, the contribution of nosocomial or hospital-acquired infections (HAIs) is unknown but could be substantial. The single most important method of preventing nosocomial infections is hand hygiene. We report a study which was conducted in 2011 to investigate adherence to hand hygiene protocols by clinicians and medical students working at Queen Elizabeth Central Hospital in Blantyre, Malawi. There were two parts to the study: a single blinded arm in which participants were observed without their knowledge by trained nurses; and a second arm which included self-completion of questionnaire after participant consent was obtained. The 2009 World Health Organization hand hygiene technique and recommendations which were adopted by Queen Elizabeth Central Hospital were used to define an opportunity for hand washing and effectiveness of hand washing. Hand hygiene effectiveness was defined as adherence to at least 6 out of 7 steps (80%) of the hand hygiene technique when using alcohol-based formulation or at least 8 out of 10 steps (80%) of the hand hygiene technique when using water and soap formulation before and after having direct contact with patients or their immediate surroundings. Clinicians were found to have disinfected their hands more than medical students (phand sanitizer and hand hygiene practice (p=0.3). Adherence to hand hygiene was found to be 23%. Most of the participants mentioned infection transmission prevention as a reason for disinfecting their hands. Other reasons mentioned included: a routine personal hand hygiene behaviour and discomfort if not washing hands. The top three reasons why they did not disinfect hands were forgetfulness, unavailability of sanitizers and negligence. Adherence to hand hygiene practice was found to be low, with forgetfulness and negligence being the major contributing factors. A hospital-wide multifaceted program aiming at clinicians and

The human hand as an inspiration for robot hand development

CERN Document Server

Santos, Veronica

2014-01-01

“The Human Hand as an Inspiration for Robot Hand Development” presents an edited collection of authoritative contributions in the area of robot hands. The results described in the volume are expected to lead to more robust, dependable, and inexpensive distributed systems such as those endowed with complex and advanced sensing, actuation, computation, and communication capabilities. The twenty-four chapters discuss the field of robotic grasping and manipulation viewed in light of the human hand’s capabilities and push the state-of-the-art in robot hand design and control. Topics discussed include human hand biomechanics, neural control, sensory feedback and perception, and robotic grasp and manipulation. This book will be useful for researchers from diverse areas such as robotics, biomechanics, neuroscience, and anthropologists.

Solutions of deformed d'Alembert equation with quantum conformal symmetry

International Nuclear Information System (INIS)

Dobrev, V.K.; Kostadinov, B.S.

1997-10-01

We construct explicit solutions of a conditionally quantum conformal invariant q-d'Alembert equation proposed earlier by one of us. We give two types of solutions - polynomial solutions and a q-deformation of the plane wave. The latter is a formal power series in the noncommutative coordinates of q-Minkowski space-time and four-momenta. This q-plane wave has analogous properties to the classical one, in particular, it has the properties of q-Lorentz covariance, and it satisfies the q-d'Alembert equation on the q-Lorentz covariant momentum cone. On the other hand, our q-plane wave is not an exponent or q-exponent. Thus, it differs conceptually from the classical plane wave and may serve as a regularization. (author)

On infinitesimal conformai deformations of surfaces

Directory of Open Access Journals (Sweden)

Юлия Степановна Федченко

2014-11-01

Full Text Available A new form of basic equations for conformai deformations is found. The equations involve tensor fields of displacement vector only. Conditions for trivial deformations as well as infinitesimal conformai deformations are studied.

Mapping of the prostate in endorectal coil-based MRI/MRSI and CT: A deformable registration and validation study

International Nuclear Information System (INIS)

Lian, J.; Xing, L.; Hunjan, S.; Dumoulin, C.; Levin, J.; Lo, A.; Watkins, R.; Rohling, K.; Giaquinto, R.; Kim, D.; Spielman, D.; Daniel, B.

2004-01-01

The endorectal coil is being increasingly used in magnetic resonance imaging (MRI) and MR spectroscopic imaging (MRSI) to obtain anatomic and metabolic images of the prostate with high signal-to-noise ratio (SNR). In practice, however, the use of endorectal probe inevitably distorts the prostate and other soft tissue organs, making the analysis and the use of the acquired image data in treatment planning difficult. The purpose of this work is to develop a deformable image registration algorithm to map the MRI/MRSI information obtained using an endorectal probe onto CT images and to verify the accuracy of the registration by phantom and patient studies. A mapping procedure involved using a thin plate spline (TPS) transformation was implemented to establish voxel-to-voxel correspondence between a reference image and a floating image with deformation. An elastic phantom with a number of implanted fiducial markers was designed for the validation of the quality of the registration. Radiographic images of the phantom were obtained before and after a series of intentionally introduced distortions. After mapping the distorted phantom to the original one, the displacements of the implanted markers were measured with respect to their ideal positions and the mean error was calculated. In patient studies, CT images of three prostate patients were acquired, followed by 3 Tesla (3 T) MR images with a rigid endorectal coil. Registration quality was estimated by the centroid position displacement and image coincidence index (CI). Phantom and patient studies show that TPS-based registration has achieved significantly higher accuracy than the previously reported method based on a rigid-body transformation and scaling. The technique should be useful to map the MR spectroscopic dataset acquired with ER probe onto the treatment planning CT dataset to guide radiotherapy planning

Intracrystalline deformation of calcite

NARCIS (Netherlands)

Bresser, J.H.P. de

1991-01-01

It is well established from observations on natural calcite tectonites that intracrystalline plastic mechanisms are important during the deformation of calcite rocks in nature. In this thesis, new data are presented on fundamental aspects of deformation behaviour of calcite under conditions where

Constraint Study for a Hand Exoskeleton: Human Hand Kinematics and Dynamics

Directory of Open Access Journals (Sweden)

Fai Chen Chen

2013-01-01

Full Text Available In the last few years, the number of projects studying the human hand from the robotic point of view has increased rapidly, due to the growing interest in academic and industrial applications. Nevertheless, the complexity of the human hand given its large number of degrees of freedom (DoF within a significantly reduced space requires an exhaustive analysis, before proposing any applications. The aim of this paper is to provide a complete summary of the kinematic and dynamic characteristics of the human hand as a preliminary step towards the development of hand devices such as prosthetic/robotic hands and exoskeletons imitating the human hand shape and functionality. A collection of data and constraints relevant to hand movements is presented, and the direct and inverse kinematics are solved for all the fingers as well as the dynamics; anthropometric data and dynamics equations allow performing simulations to understand the behavior of the finger.

Deformable paper origami optoelectronic devices

KAUST Repository

He, Jr-Hau

2017-01-19

Deformable optoelectronic devices are provided, including photodetectors, photodiodes, and photovoltaic cells. The devices can be made on a variety of paper substrates, and can include a plurality of fold segments in the paper substrate creating a deformable pattern. Thin electrode layers and semiconductor nanowire layers can be attached to the substrate, creating the optoelectronic device. The devices can be highly deformable, e.g. capable of undergoing strains of 500% or more, bending angles of 25° or more, and/or twist angles of 270° or more. Methods of making the deformable optoelectronic devices and methods of using, e.g. as a photodetector, are also provided.

HandTutor™ enhanced hand rehabilitation after stroke--a pilot study.

Science.gov (United States)

Carmeli, Eli; Peleg, Sara; Bartur, Gadi; Elbo, Enbal; Vatine, Jean-Jacques

2011-12-01

This study assessed the potential therapeutic benefi t of using HandTutor™ in combination with traditional rehabilitation in a post-stroke sub-acute population. The study compares an experimental group receiving traditional therapy combined with HandTutorTM treatment, against a control group receiving only traditional therapy. An assessor-blinded, randomized controlled pilot trial, was conducted in the Reuth rehabilitation unit in Israel. Thirty-one stroke patients in the sub-acute phase, were randomly assigned to one of the two groups (experimental or control) in sets of three. The experimental group (n = 16) underwent a hand rehabilitation programme using the HandTutorTM combined with traditional therapy. The control group (n = 15) received only traditional therapy. The treatment schedules for both groups were of similar duration and frequency. Improvements were evaluated using three indicators: 1) The Brunnström-Fugl-Meyer (FM) test, 2) the Box and Blocks (B&B) test and 3) improvement parameters as determined by the HandTutorTM software. Following 15 consecutive treatment sessions, a signifi cant improvement was observed within the experimental group (95% confi dence intervals) compared with the control group: B&B p = 0.015; FM p = 0.041, HandTutor™ performance accuracy on x axis and performance accuracy on y axis p stroke hand function rehabilitation.

Neural representation of hand kinematics during prehension in posterior parietal cortex of the macaque monkey.

Science.gov (United States)

Chen, Jessie; Reitzen, Shari D; Kohlenstein, Jane B; Gardner, Esther P

2009-12-01

Studies of hand manipulation neurons in posterior parietal cortex of monkeys suggest that their spike trains represent objects by the hand postures needed for grasping or by the underlying patterns of muscle activation. To analyze the role of hand kinematics and object properties in a trained prehension task, we correlated the firing rates of neurons in anterior area 5 with hand behaviors as monkeys grasped and lifted knobs of different shapes and locations in the workspace. Trials were divided into four classes depending on the approach trajectory: forward, lateral, and local approaches, and regrasps. The task factors controlled by the animal-how and when he used the hand-appeared to play the principal roles in modulating firing rates of area 5 neurons. In all, 77% of neurons studied (58/75) showed significant effects of approach style on firing rates; 80% of the population responded at higher rates and for longer durations on forward or lateral approaches that included reaching, wrist rotation, and hand preshaping prior to contact, but only 13% distinguished the direction of reach. The higher firing rates in reach trials reflected not only the arm movements needed to direct the hand to the target before contact, but persisted through the contact, grasp, and lift stages. Moreover, the approach style exerted a stronger effect on firing rates than object features, such as shape and location, which were distinguished by half of the population. Forty-three percent of the neurons signaled both the object properties and the hand actions used to acquire them. However, the spread in firing rates evoked by each knob on reach and no-reach trials was greater than distinctions between different objects grasped with the same approach style. Our data provide clear evidence for synergies between reaching and grasping that may facilitate smooth, coordinated actions of the arm and hand.

Stochastic deformation of a thermodynamic symplectic structure

OpenAIRE

Kazinski, P. O.

2008-01-01

A stochastic deformation of a thermodynamic symplectic structure is studied. The stochastic deformation procedure is analogous to the deformation of an algebra of observables like deformation quantization, but for an imaginary deformation parameter (the Planck constant). Gauge symmetries of thermodynamics and corresponding stochastic mechanics, which describes fluctuations of a thermodynamic system, are revealed and gauge fields are introduced. A physical interpretation to the gauge transform...

Numerical simulation of mechanisms of deformation,failure and energy dissipation in porous rock media subjected to wave stresses

Institute of Scientific and Technical Information of China (English)

无

2010-01-01

The pore characteristics,mineral compositions,physical and mechanical properties of the subarkose sandstones were acquired by means of CT scan,X-ray diffraction and physical tests.A few physical models possessing the same pore characteristics and matrix properties but different porosities compared to the natural sandstones were developed.The 3D finite element models of the rock media with varied porosities were established based on the CT image processing of the physical models and the MIMICS software platform.The failure processes of the porous rock media loaded by the split Hopkinson pressure bar(SHPB) were simulated by satisfying the elastic wave propagation theory.The dynamic responses,stress transition,deformation and failure mechanisms of the porous rock media subjected to the wave stresses were analyzed.It is shown that an explicit and quantitative analysis of the stress,strain and deformation and failure mechanisms of porous rocks under the wave stresses can be achieved by using the developed 3D finite element models.With applied wave stresses of certain amplitude and velocity,no evident pore deformation was observed for the rock media with a porosity less than 15%.The deformation is dominantly the combination of microplasticity(shear strain),cracking(tensile strain) of matrix and coalescence of the cracked regions around pores.Shear stresses lead to microplasticity,while tensile stresses result in cracking of the matrix.Cracking and coalescence of the matrix elements in the neighborhood of pores resulted from the high transverse tensile stress or tensile strain which exceeded the threshold values.The simulation results of stress wave propagation,deformation and failure mechanisms and energy dissipation in porous rock media were in good agreement with the physical tests.The present study provides a reference for analyzing the intrinsic mechanisms of the complex dynamic response,stress transit mode,deformation and failure mechanisms and the disaster

The Avocado Hand

LENUS (Irish Health Repository)

Rahmani, G

2017-11-01

Accidental self-inflicted knife injuries to digits are a common cause of tendon and nerve injury requiring hand surgery. There has been an apparent increase in avocado related hand injuries. Classically, the patients hold the avocado in their non-dominant hand while using a knife to cut\\/peel the fruit with their dominant hand. The mechanism of injury is usually a stabbing injury to the non-dominant hand as the knife slips past the stone, through the soft avocado fruit. Despite their apparent increased incidence, we could not find any cases in the literature which describe the “avocado hand”. We present a case of a 32-year-old woman who sustained a significant hand injury while preparing an avocado. She required exploration and repair of a digital nerve under regional anaesthesia and has since made a full recovery.

Deformation aspects of time dependent fracture

International Nuclear Information System (INIS)

Li, C.Y.; Turner, A.P.L.; Diercks, D.R.; Laird, C.; Langdon, T.G.; Nix, W.D.; Swindeman, R.; Wolfer, W.G.; Woodford, D.A.

1979-01-01

For all metallic materials, particularly at elevated temperatures, deformation plays an important role in fracture. On the macro-continuum level, the inelastic deformation behavior of the material determines how stress is distributed in the body and thus determines the driving force for fracture. At the micro-continuum level, inelastic deformation alters the elastic stress singularity at the crack tip and so determines the local environment in which crack advance takes place. At the microscopic and mechanistic level, there are many possibilities for the mechanisms of deformation to be related to those for crack initiation and growth. At elevated temperatures, inelastic deformation in metallic systems is time dependent so that the distribution of stress in a body will vary with time, affecting conditions for crack initiation and propagation. Creep deformation can reduce the tendency for fracture by relaxing the stresses at geometric stress concentrations. It can also, under suitable constraints, cause a concentration of stresses at specific loading points as a result of relaxation elsewhere in the body. A combination of deformation and unequal heating, as in welding, can generate large residual stress which cannot be predicted from the external loads on the body. Acceleration of deformation by raising the temperature can be an effective way to relieve such residual stresses

Comparison of Single Visit Post Endodontic Pain Using Mtwo Rotary and Hand K-File Instruments: A Randomized Clinical Trial.

Science.gov (United States)

Kashefinejad, Mohamad; Harandi, Azade; Eram, Saeed; Bijani, Ali

2016-01-01

Pain is an unpleasant outcome of endodontic treatment that can be unbearable to patients. Instrumentation techniques may affect the frequency and intensity of post-endodontic pain. This study aimed to compare single visit post endodontic pain using Mtwo (NiTi) rotary and hand K-file instruments. In this randomized controlled trial, 60 teeth with symptomatic irreversible pulpitis in 53 patients were selected and randomly assigned into two groups of 30 teeth. In group A, the root canals were prepared with Mtwo (NiTi) rotary instruments. In group B, the root canals were prepared with hand K-file instruments. Pain assessment was implemented using visual analog scale (VAS) at four, eight, 12 and 24 hours after treatment. The acquired data were analyzed using chi-square, Mann-Whitney U and Student's t-test (Protary instruments experienced significantly less post-endodontic pain than those treated with hand instruments (Protary instruments in root canal preparation contributed to lower incidence of postoperative pain than hand K-files.

On the absence of InSAR-detected volcano deformation spanning the 1995-1996 and 1999 eruptions of Shishaldin Volcano, Alaska

Science.gov (United States)

Moran, S.C.; Kwoun, O.; Masterlark, Timothy; Lu, Z.

2006-01-01

Shishaldin Volcano, a large, frequently active basaltic-andesite volcano located on Unimak Island in the Aleutian Arc of Alaska, had a minor eruption in 1995–1996 and a VEI 3 sub-Plinian basaltic eruption in 1999. We used 21 synthetic aperture radar images acquired by ERS-1, ERS-2, JERS-1, and RADARSAT-1 satellites to construct 12 coherent interferograms that span most of the 1993–2003 time interval. All interferograms lack coherence within ∼5 km of the summit, primarily due to persistent snow and ice cover on the edifice. Remarkably, in the 5–15 km distance range where interferograms are coherent, the InSAR images show no intrusion- or withdrawal-related deformation at Shishaldin during this entire time period. However, several InSAR images do show deformation associated with a shallow ML 5.2 earthquake located ∼14 km west of Shishaldin that occurred 6 weeks before the 1999 eruption. We use a theoretical model to predict deformation magnitudes due to a volumetric expansion source having a volume equivalent to the 1999 erupted volume, and find that deformation magnitudes for sources shallower than 10 km are within the expected detection capabilities for interferograms generated from C-band ERS 1/2 and RADARSAT-1 synthetic aperture radar images. We also find that InSAR images cannot resolve relatively shallow deformation sources (1–2 km below sea level) due to spatial gaps in the InSAR images caused by lost coherence. The lack of any deformation, particularly for the 1999 eruption, leads us to speculate that magma feeding eruptions at the summit moves rapidly (at least 80m/day) from > 10 km depth, and that the intrusion–eruption cycle at Shishaldin does not produce significant permanent deformation at the surface.

Quantifying the Erlenmeyer flask deformity

Science.gov (United States)

Carter, A; Rajan, P S; Deegan, P; Cox, T M; Bearcroft, P

2012-01-01

Objective Erlenmeyer flask deformity is a common radiological finding in patients with Gaucher′s disease; however, no definition of this deformity exists and the reported prevalence of the deformity varies widely. To devise an easily applied definition of this deformity, we investigated a cohort of knee radiographs in which there was consensus between three experienced radiologists as to the presence or absence of Erlenmeyer flask morphology. Methods Using the presence or absence of Erlenmeyer flask morphology as a benchmark, we measured the diameter of the femur at the level of the physeal scar and serially at defined intervals along the metadiaphysis. Results A measured ratio in excess of 0.57 between the diameter of the femoral shaft 4 cm from the physis to the diameter of the physeal baseline itself on a frontal radiograph of the knee predicted the Erlenmeyer flask deformity with 95.6% sensitivity and 100% specificity in our series of 43 independently diagnosed adults with Gaucher′s disease. Application of this method to the distal femur detected the Erlenmeyer flask deformity reproducibly and was simple to carry out. Conclusion Unlike diagnostic assignments based on subjective review, our simple procedure for identifying the modelling deformity is based on robust quantitative measurement: it should facilitate comparative studies between different groups of patients, and may allow more rigorous exploration of the pathogenesis of the complex osseous manifestations of Gaucher′s disease to be undertaken. PMID:22010032

Microstructure evolution and deformation mechanism change in 0.98C-8.3Mn-0.04N steel during compressive deformation

International Nuclear Information System (INIS)

Wang, T.S.; Hou, R.J.; Lv, B.; Zhang, M.; Zhang, F.C.

2007-01-01

The microstructure evolution and the deformation mechanism change in 0.98C-8.3Mn-0.04N steel during compressive deformation at room temperature have been studied as a function of the reduction in the range of 20-60%. Experimental results show that with the reduction increasing the microstructure of the deformed sample changes from dislocation substructures into the dominant twins plus dislocations. This suggests that the plastic deformation mechanism changes from the dislocation slip to the dominant deformation twinning. The minimum reduction for deformation twins starting is estimated to be at between 30 and 40%. With the reduction further increases to more than 40%, the deformation twinning is operative and the thickness of deformation twins gradually decreases to nanoscale and shear bands occur. These high-density twins can be curved by the formation of shear bands. In addition, both transmission electron microscopy and X-ray diffraction examinations confirm the inexistence of deformation-induced martensites in these deformed samples

Quantitative stress measurement of elastic deformation using mechanoluminescent sensor: An intensity ratio model

Science.gov (United States)

Cai, Tao; Guo, Songtao; Li, Yongzeng; Peng, Di; Zhao, Xiaofeng; Liu, Yingzheng

2018-04-01

The mechanoluminescent (ML) sensor is a newly developed non-invasive technique for stress/strain measurement. However, its application has been mostly restricted to qualitative measurement due to the lack of a well-defined relationship between ML intensity and stress. To achieve accurate stress measurement, an intensity ratio model was proposed in this study to establish a quantitative relationship between the stress condition and its ML intensity in elastic deformation. To verify the proposed model, experiments were carried out on a ML measurement system using resin samples mixed with the sensor material SrAl2O4:Eu2+, Dy3+. The ML intensity ratio was found to be dependent on the applied stress and strain rate, and the relationship acquired from the experimental results agreed well with the proposed model. The current study provided a physical explanation for the relationship between ML intensity and its stress condition. The proposed model was applicable in various SrAl2O4:Eu2+, Dy3+-based ML measurement in elastic deformation, and could provide a useful reference for quantitative stress measurement using the ML sensor in general.

Ability of Hand Hygiene Interventions Using Alcohol-Based Hand Sanitizers and Soap To Reduce Microbial Load on Farmworker Hands Soiled during Harvest.

Science.gov (United States)

de Aceituno, Anna Fabiszewski; Bartz, Faith E; Hodge, Domonique Watson; Shumaker, David J; Grubb, James E; Arbogast, James W; Dávila-Aviña, Jorgé; Venegas, Fabiola; Heredia, Norma; García, Santos; Leon, Juan S

2015-11-01

Effective hand hygiene is essential to prevent the spread of pathogens on produce farms and reduce foodborne illness. The U.S. Food and Drug Administration Food Safety Modernization Act Proposed Rule for Produce Safety recommends the use of soap and running water for hand hygiene of produce handlers. The use of alcohol-based hand sanitizer (ABHS) may be an effective alternative hygiene intervention where access to water is limited. There are no published data on the efficacy of either soap or ABHS-based interventions to reduce microbial contamination in agricultural settings. The goal of this study was to assess the ability of two soap-based (traditional or pumice) and two ABHS-based (label-use or two-step) hygiene interventions to reduce microbes (coliforms, Escherichia coli, and Enterococcus spp.) and soil (absorbance of hand rinsate at 600 nm [A600]) on farmworker hands after harvesting produce, compared with the results for a no-hand-hygiene control. With no hand hygiene, farmworker hands were soiled (median A600, 0.48) and had high concentrations of coliforms (geometric mean, 3.4 log CFU per hand) and Enterococcus spp. (geometric mean, 5.3 log CFU per hand) after 1 to 2 h of harvesting tomatoes. Differences in microbial loads in comparison to the loads in the control group varied by indicator organism and hygiene intervention (0 to 2.3 log CFU per hand). All interventions yielded lower concentrations of Enterococcus spp. and E. coli (P hands (P hand washing with soap at reducing indicator organisms on farmworker hands. Based on these results, ABHS is an efficacious hand hygiene solution for produce handlers, even on soiled hands.

Hand Therapy

Science.gov (United States)

... from conditions such as carpal tunnel syndrome and tennis elbow , as well as from chronic problems such as ... Tools Advice from a Certified Hand Therapist on Tennis Elbow Advice from a Certified Hand Therapist: Living with( ...

Plastic deformation of indium nanostructures

International Nuclear Information System (INIS)

Lee, Gyuhyon; Kim, Ju-Young; Burek, Michael J.; Greer, Julia R.; Tsui, Ting Y.

2011-01-01

Highlights: → Indium nanopillars display two different deformation mechanisms. → ∼80% exhibited low flow stresses near that of bulk indium. → Low strength nanopillars have strain rate sensitivity similar to bulk indium. → ∼20% of compressed indium nanopillars deformed at nearly theoretical strengths. → Low-strength samples do not exhibit strength size effects. - Abstract: Mechanical properties and morphology of cylindrical indium nanopillars, fabricated by electron beam lithography and electroplating, are characterized in uniaxial compression. Time-dependent deformation and influence of size on nanoscale indium mechanical properties were investigated. The results show two fundamentally different deformation mechanisms which govern plasticity in these indium nanostructures. We observed that the majority of indium nanopillars deform at engineering stresses near the bulk values (Type I), with a small fraction sustaining flow stresses approaching the theoretical limit for indium (Type II). The results also show the strain rate sensitivity and flow stresses in Type I indium nanopillars are similar to bulk indium with no apparent size effects.

Interactive Character Deformation Using Simplified Elastic Models

NARCIS (Netherlands)

Luo, Z.

2016-01-01

This thesis describes the results of our research into realistic skin and model deformation methods aimed at the field of character deformation and animation. The main contributions lie in the properties of our deformation scheme. Our approach preserves the volume of the deformed object while

Nonlinear Deformable-body Dynamics

CERN Document Server

Luo, Albert C J

2010-01-01

"Nonlinear Deformable-body Dynamics" mainly consists in a mathematical treatise of approximate theories for thin deformable bodies, including cables, beams, rods, webs, membranes, plates, and shells. The intent of the book is to stimulate more research in the area of nonlinear deformable-body dynamics not only because of the unsolved theoretical puzzles it presents but also because of its wide spectrum of applications. For instance, the theories for soft webs and rod-reinforced soft structures can be applied to biomechanics for DNA and living tissues, and the nonlinear theory of deformable bodies, based on the Kirchhoff assumptions, is a special case discussed. This book can serve as a reference work for researchers and a textbook for senior and postgraduate students in physics, mathematics, engineering and biophysics. Dr. Albert C.J. Luo is a Professor of Mechanical Engineering at Southern Illinois University, Edwardsville, IL, USA. Professor Luo is an internationally recognized scientist in the field of non...

Developing a Virtual Rock Deformation Laboratory

Science.gov (United States)

Zhu, W.; Ougier-simonin, A.; Lisabeth, H. P.; Banker, J. S.

2012-12-01

Experimental rock physics plays an important role in advancing earthquake research. Despite its importance in geophysics, reservoir engineering, waste deposits and energy resources, most geology departments in U.S. universities don't have rock deformation facilities. A virtual deformation laboratory can serve as an efficient tool to help geology students naturally and internationally learn about rock deformation. Working with computer science engineers, we built a virtual deformation laboratory that aims at fostering user interaction to facilitate classroom and outreach teaching and learning. The virtual lab is built to center around a triaxial deformation apparatus in which laboratory measurements of mechanical and transport properties such as stress, axial and radial strains, acoustic emission activities, wave velocities, and permeability are demonstrated. A student user can create her avatar to enter the virtual lab. In the virtual lab, the avatar can browse and choose among various rock samples, determine the testing conditions (pressure, temperature, strain rate, loading paths), then operate the virtual deformation machine to observe how deformation changes physical properties of rocks. Actual experimental results on the mechanical, frictional, sonic, acoustic and transport properties of different rocks at different conditions are compiled. The data acquisition system in the virtual lab is linked to the complied experimental data. Structural and microstructural images of deformed rocks are up-loaded and linked to different deformation tests. The integration of the microstructural image and the deformation data allows the student to visualize how forces reshape the structure of the rock and change the physical properties. The virtual lab is built using the Game Engine. The geological background, outstanding questions related to the geological environment, and physical and mechanical concepts associated with the problem will be illustrated on the web portal. In

Mapping three-dimensional surface deformation by combining multiple-aperture interferometry and conventional interferometry: Application to the June 2007 eruption of Kilauea Volcano, Hawaii

Science.gov (United States)

Jung, H.-S.; Lu, Z.; Won, J.-S.; Poland, Michael P.; Miklius, Asta

2011-01-01

Surface deformation caused by an intrusion and small eruption during June 17-19, 2007, along the East Rift Zone of Kilauea Volcano, Hawaii, was three-dimensionally reconstructed from radar interferograms acquired by the Advanced Land Observing Satellite (ALOS) phased-array type L-band synthetic aperture radar (SAR) (PALSAR) instrument. To retrieve the 3-D surface deformation, a method that combines multiple-aperture interferometry (MAI) and conventional interferometric SAR (InSAR) techniques was applied to one ascending and one descending ALOS PALSAR interferometric pair. The maximum displacements as a result of the intrusion and eruption are about 0.8, 2, and 0.7 m in the east, north, and up components, respectively. The radar-measured 3-D surface deformation agrees with GPS data from 24 sites on the volcano, and the root-mean-square errors in the east, north, and up components of the displacement are 1.6, 3.6, and 2.1 cm, respectively. Since a horizontal deformation of more than 1 m was dominantly in the north-northwest-south-southeast direction, a significant improvement of the north-south component measurement was achieved by the inclusion of MAI measurements that can reach a standard deviation of 3.6 cm. A 3-D deformation reconstruction through the combination of conventional InSAR and MAI will allow for better modeling, and hence, a more comprehensive understanding, of the source geometry associated with volcanic, seismic, and other processes that are manifested by surface deformation.

Creeping eruption of the hand in an Iranian patient: Cutaneous larva migrans

Directory of Open Access Journals (Sweden)

Zabihollah Shahmoradi

2014-01-01

Full Text Available Cutaneous larva migrans (CLM, a serpiginous cutaneous eruption is the most commonly acquired tropical dermatosis. It is caused by infection with hookworm larvae in tropical and sub-tropical areas, and people who have a history of travel in these countries. The most frequent location of CLM is the distal lower extremities or buttocks. We describe a case of 57-year-old Iranian female patient with CLM of hand (unusual site without traveling to endemic countries that was successfully treated with oral albendazole. To the best of our knowledge, this is the first report of CLM in Iran.

Laparoscopic cholecystectomy poses physical injury risk to surgeons: analysis of hand technique and standing position.

Science.gov (United States)

Youssef, Yassar; Lee, Gyusung; Godinez, Carlos; Sutton, Erica; Klein, Rosemary V; George, Ivan M; Seagull, F Jacob; Park, Adrian

2011-07-01

This study compares surgical techniques and surgeon's standing position during laparoscopic cholecystectomy (LC), investigating each with respect to surgeons' learning, performance, and ergonomics. Little homogeneity exists in LC performance and training. Variations in standing position (side-standing technique vs. between-standing technique) and hand technique (one-handed vs. two-handed) exist. Thirty-two LC procedures performed on a virtual reality simulator were video-recorded and analyzed. Each subject performed four different procedures: one-handed/side-standing, one-handed/between-standing, two-handed/side-standing, and two-handed/between-standing. Physical ergonomics were evaluated using Rapid Upper Limb Assessment (RULA). Mental workload assessment was acquired with the National Aeronautics and Space Administration-Task Load Index (NASA-TLX). Virtual reality (VR) simulator-generated performance evaluation and a subjective survey were analyzed. RULA scores were consistently lower (indicating better ergonomics) for the between-standing technique and higher (indicating worse ergonomics) for the side-standing technique, regardless of whether one- or two-handed. Anatomical scores overall showed side-standing to have a detrimental effect on the upper arms and trunk. The NASA-TLX showed significant association between the side-standing position and high physical demand, effort, and frustration (p<0.05). The two-handed technique in the side-standing position required more effort than the one-handed (p<0.05). No difference in operative time or complication rate was demonstrated among the four procedures. The two-handed/between-standing method was chosen as the best procedure to teach and standardize. Laparoscopic cholecystectomy poses a risk of physical injury to the surgeon. As LC is currently commonly performed in the United States, the left side-standing position may lead to increased physical demand and effort, resulting in ergonomically unsound conditions for

SU-E-J-89: Comparative Analysis of MIM and Velocity’s Image Deformation Algorithm Using Simulated KV-CBCT Images for Quality Assurance

Energy Technology Data Exchange (ETDEWEB)

Cline, K; Narayanasamy, G; Obediat, M; Stanley, D; Stathakis, S; Kirby, N [University of Texas Health Science Center at San Antonio, Cancer Therapy and Research Center, San Antonio, TX (United States); Kim, H [University of California San Francisco, San Francisco, CA (United States)

2015-06-15

Purpose: Deformable image registration (DIR) is used routinely in the clinic without a formalized quality assurance (QA) process. Using simulated deformations to digitally deform images in a known way and comparing to DIR algorithm predictions is a powerful technique for DIR QA. This technique must also simulate realistic image noise and artifacts, especially between modalities. This study developed an algorithm to create simulated daily kV cone-beam computed-tomography (CBCT) images from CT images for DIR QA between these modalities. Methods: A Catphan and physical head-and-neck phantom, with known deformations, were used. CT and kV-CBCT images of the Catphan were utilized to characterize the changes in Hounsfield units, noise, and image cupping that occur between these imaging modalities. The algorithm then imprinted these changes onto a CT image of the deformed head-and-neck phantom, thereby creating a simulated-CBCT image. CT and kV-CBCT images of the undeformed and deformed head-and-neck phantom were also acquired. The Velocity and MIM DIR algorithms were applied between the undeformed CT image and each of the deformed CT, CBCT, and simulated-CBCT images to obtain predicted deformations. The error between the known and predicted deformations was used as a metric to evaluate the quality of the simulated-CBCT image. Ideally, the simulated-CBCT image registration would produce the same accuracy as the deformed CBCT image registration. Results: For Velocity, the mean error was 1.4 mm for the CT-CT registration, 1.7 mm for the CT-CBCT registration, and 1.4 mm for the CT-simulated-CBCT registration. These same numbers were 1.5, 4.5, and 5.9 mm, respectively, for MIM. Conclusion: All cases produced similar accuracy for Velocity. MIM produced similar values of accuracy for CT-CT registration, but was not as accurate for CT-CBCT registrations. The MIM simulated-CBCT registration followed this same trend, but overestimated MIM DIR errors relative to the CT

SU-E-J-89: Comparative Analysis of MIM and Velocity’s Image Deformation Algorithm Using Simulated KV-CBCT Images for Quality Assurance

International Nuclear Information System (INIS)

Cline, K; Narayanasamy, G; Obediat, M; Stanley, D; Stathakis, S; Kirby, N; Kim, H

2015-01-01

Purpose: Deformable image registration (DIR) is used routinely in the clinic without a formalized quality assurance (QA) process. Using simulated deformations to digitally deform images in a known way and comparing to DIR algorithm predictions is a powerful technique for DIR QA. This technique must also simulate realistic image noise and artifacts, especially between modalities. This study developed an algorithm to create simulated daily kV cone-beam computed-tomography (CBCT) images from CT images for DIR QA between these modalities. Methods: A Catphan and physical head-and-neck phantom, with known deformations, were used. CT and kV-CBCT images of the Catphan were utilized to characterize the changes in Hounsfield units, noise, and image cupping that occur between these imaging modalities. The algorithm then imprinted these changes onto a CT image of the deformed head-and-neck phantom, thereby creating a simulated-CBCT image. CT and kV-CBCT images of the undeformed and deformed head-and-neck phantom were also acquired. The Velocity and MIM DIR algorithms were applied between the undeformed CT image and each of the deformed CT, CBCT, and simulated-CBCT images to obtain predicted deformations. The error between the known and predicted deformations was used as a metric to evaluate the quality of the simulated-CBCT image. Ideally, the simulated-CBCT image registration would produce the same accuracy as the deformed CBCT image registration. Results: For Velocity, the mean error was 1.4 mm for the CT-CT registration, 1.7 mm for the CT-CBCT registration, and 1.4 mm for the CT-simulated-CBCT registration. These same numbers were 1.5, 4.5, and 5.9 mm, respectively, for MIM. Conclusion: All cases produced similar accuracy for Velocity. MIM produced similar values of accuracy for CT-CT registration, but was not as accurate for CT-CBCT registrations. The MIM simulated-CBCT registration followed this same trend, but overestimated MIM DIR errors relative to the CT

Daily exposure to hand arm vibration by different electric olive beaters

Directory of Open Access Journals (Sweden)

Angela Calvo

2014-11-01

Full Text Available The electric hand held olive harvesters have a low weight (about 2 kg and cause the fruit pick up by means of impacts produced by their vibrational tools: for this reason they transmit elevated vibration doses to the operator’s hand arm system during the work. In this paper electric beaters of different manufacturers and different models were considered, to analyse their vibrational behaviour in field, during the olive harvesting campaign in a site located in Northern Italy. One operator did the tests, to avoid the operator’s uncertainty on the obtained results. All the five examined beaters gave high acceleration values (in a range from 10 to 26 ms–2, but the most restricting data were the daily vibration exposures, calculated considering the real working duration time acquired in field, almost ranged between 10 and 18 ms–2. Also the operator posture during the work (with the arms over the shoulders may set health problems, related to upper limb disorders, other than the already known musculoskeletal, nervous and vascular pathologies.

The Spherical Deformation Model

DEFF Research Database (Denmark)

Hobolth, Asgar

2003-01-01

Miller et al. (1994) describe a model for representing spatial objects with no obvious landmarks. Each object is represented by a global translation and a normal deformation of a sphere. The normal deformation is defined via the orthonormal spherical-harmonic basis. In this paper we analyse the s...

Surface deformation monitoring of Sinabung volcano using multi temporal InSAR method and GIS analysis for affected area assessment

Science.gov (United States)

Aditiya, A.; Aoki, Y.; Anugrah, R. D.

2018-04-01

Sinabung Volcano which located in northern part of Sumatera island is part of a hundred active volcano in Indonesia. Surface deformation is detected over Sinabung Volcano and surrounded area since the first eruption in 2010 after 400 years long rest. We present multi temporal Interferometric Synthetic Aperture Radar (InSAR) time-series method of ALOS-2 L-band SAR data acquired from December 2014 to July 2017 to reveal surface deformation with high spatial resolution. The method includes focusing the SAR data, generating interferogram and phase unwrapping using SNAPHU tools. The result reveal significant deformation over Sinabung Volcano areas at rates up to 10 cm during observation period and the highest deformation occurs in western part which is trajectory of lava. We concluded the observed deformation primarily caused by volcanic activity respectively after long period of rest. In addition, Geographic Information System (GIS) analysis produces disaster affected areas of Sinabung eruption. GIS is reliable technique to estimate the impact of the hazard scenario to the exposure data and develop scenarios of disaster impacts to inform their contingency and emergency plan. The GIS results include the estimated affected area divided into 3 zones based on pyroclastic lava flow and pyroclastic fall (incandescent rock and ash). The highest impact is occurred in zone II due to many settlements are scattered in this zone. This information will be support stakeholders to take emergency preparation for disaster reduction. The continuation of this high rate of decline tends to endanger the population in next periods.

Hand Hygiene Practices and Microbial Investigation of Hand Contact Swab among Physiotherapists in an Ebola Endemic Region: Implications for Public Health

Science.gov (United States)

Maduako, V.; Ibeneme, G. C.; Ezuma, A.; Ettu, T. U.; Onyemelukwe, N. F.; Fortwengel, G.

2017-01-01

Background Hand hygiene practices (HHP), as a critical component of infection prevention/control, were investigated among physiotherapists in an Ebola endemic region. Method A standardized instrument was administered to 44 randomly selected physiotherapists (23 males and 21 females), from three tertiary hospitals in Enugu, Nigeria. Fifteen participants (aged 22–59 years) participated in focus group discussions (FGDs) and comprised 19 participants in a subsequent laboratory study. After treatment, the palms/fingers of physiotherapists were swabbed and cultured, then incubated aerobically overnight at 37°C, and examined for microbial growths. An antibiogram of the bacterial isolates was obtained. Results The majority (34/77.3%) of physiotherapists were aware of the HHP protocol, yet only 15/44.1% rated self-compliance at 71–100%. FGDs identified forgetfulness/inadequate HHP materials/infrastructure as the major barriers to HHP. Staphylococcus aureus were the most prevalent organisms, prior to (8/53.33%) and after (4/26.67%) HPP, while Pseudomonas spp. were acquired thereafter. E. coli were the most antibiotic resistant microbes but were completely removed after HHP. Ciprofloxacin and streptomycin were the most effective antibiotics. Conclusion Poor implementation of HPP was observed due to inadequate materials/infrastructure/poor behavioral orientation. Possibly, some HPP materials were contaminated; hence, new microbes were acquired. Since HPP removed the most antibiotic resistant microbes, it might be more effective in infection control than antibiotic medication. PMID:28691027

Hand Hygiene Practices and Microbial Investigation of Hand Contact Swab among Physiotherapists in an Ebola Endemic Region: Implications for Public Health.

Science.gov (United States)

Ibeneme, S; Maduako, V; Ibeneme, G C; Ezuma, A; Ettu, T U; Onyemelukwe, N F; Limaye, D; Fortwengel, G

2017-01-01

Hand hygiene practices (HHP), as a critical component of infection prevention/control, were investigated among physiotherapists in an Ebola endemic region. A standardized instrument was administered to 44 randomly selected physiotherapists (23 males and 21 females), from three tertiary hospitals in Enugu, Nigeria. Fifteen participants (aged 22-59 years) participated in focus group discussions (FGDs) and comprised 19 participants in a subsequent laboratory study. After treatment, the palms/fingers of physiotherapists were swabbed and cultured, then incubated aerobically overnight at 37°C, and examined for microbial growths. An antibiogram of the bacterial isolates was obtained. The majority (34/77.3%) of physiotherapists were aware of the HHP protocol, yet only 15/44.1% rated self-compliance at 71-100%. FGDs identified forgetfulness/inadequate HHP materials/infrastructure as the major barriers to HHP. Staphylococcus aureus were the most prevalent organisms, prior to (8/53.33%) and after (4/26.67%) HPP, while Pseudomonas spp. were acquired thereafter. E. coli were the most antibiotic resistant microbes but were completely removed after HHP. Ciprofloxacin and streptomycin were the most effective antibiotics. Poor implementation of HPP was observed due to inadequate materials/infrastructure/poor behavioral orientation. Possibly, some HPP materials were contaminated; hence, new microbes were acquired. Since HPP removed the most antibiotic resistant microbes, it might be more effective in infection control than antibiotic medication.

Corrosion behavior of HPT-deformed TiNi alloys in cell culture medium

Science.gov (United States)

Shri, D. N. Awang; Tsuchiya, K.; Yamamoto, A.

2017-09-01

indicates the passive nature of native oxides formed on the surface of the samples. The polarization curve, on the other hand, indicates that the HPT deformation was found to shift the passive current to nobler region. The passive region current density is found to be lower than that of the BHPT, suggesting the passive film formed on the surface of HPT-deformed samples is more protective than that of the BHPT sample. This study has shown that nanocrystallization and amorphization induced by severe plastic deformation change the corrosion behavior of TiNi alloys.

Passive sorting of capsules by deformability

Science.gov (United States)

Haener, Edgar; Juel, Anne

We study passive sorting according to deformability of liquid-filled ovalbumin-alginate capsules. We present results for two sorting geometries: a straight channel with a half-cylindrical obstruction and a pinched flow fractioning device (PFF) adapted for use with capsules. In the half-cylinder device, the capsules deform as they encounter the obstruction, and travel around the half-cylinder. The distance from the capsule's centre of mass to the surface of the half-cylinder depends on deformability, and separation between capsules of different deformability is amplified by diverging streamlines in the channel expansion downstream of the obstruction. We show experimentally that capsules can be sorted according to deformability with their downstream position depending on capillary number only, and we establish the sensitivity of the device to experimental variability. In the PFF device, particles are compressed against a wall using a strong pinching flow. We show that capsule deformation increases with the intensity of the pinching flow, but that the downstream capsule position is not set by deformation in the device. However, when using the PFF device like a T-Junction, we achieve improved sorting resolution compared to the half-cylinder device.

Perceptual transparency from image deformation.

Science.gov (United States)

Kawabe, Takahiro; Maruya, Kazushi; Nishida, Shin'ya

2015-08-18

Human vision has a remarkable ability to perceive two layers at the same retinal locations, a transparent layer in front of a background surface. Critical image cues to perceptual transparency, studied extensively in the past, are changes in luminance or color that could be caused by light absorptions and reflections by the front layer, but such image changes may not be clearly visible when the front layer consists of a pure transparent material such as water. Our daily experiences with transparent materials of this kind suggest that an alternative potential cue of visual transparency is image deformations of a background pattern caused by light refraction. Although previous studies have indicated that these image deformations, at least static ones, play little role in perceptual transparency, here we show that dynamic image deformations of the background pattern, which could be produced by light refraction on a moving liquid's surface, can produce a vivid impression of a transparent liquid layer without the aid of any other visual cues as to the presence of a transparent layer. Furthermore, a transparent liquid layer perceptually emerges even from a randomly generated dynamic image deformation as long as it is similar to real liquid deformations in its spatiotemporal frequency profile. Our findings indicate that the brain can perceptually infer the presence of "invisible" transparent liquids by analyzing the spatiotemporal structure of dynamic image deformation, for which it uses a relatively simple computation that does not require high-level knowledge about the detailed physics of liquid deformation.

Hand hygiene--evaluation of three disinfectant hand sanitizers in a community setting.

Directory of Open Access Journals (Sweden)

Rita Babeluk

Full Text Available Hand hygiene is acknowledged as the single most important measure to prevent nosocomial infections in the healthcare setting. Similarly, in non-clinical settings, hand hygiene is recognised as a key element in helping prevent the spread of infectious diseases. The aim of this study was to evaluate the efficacy of three different disinfectant hand sanitizers in reducing the burden of bacterial hand contamination in 60 healthy volunteers in a community setting, both before and after education about the correct use of hand sanitizers. The study is the first to evaluate the efficacy and ease of use of different formulations of hand rubs used by the general population. The products tested were: Sterillium (perfumed, liquid, desderman pure gel (odorless, gel and Lavit (perfumed, spray. Sterillium and desderman are EN1500 (hygienic hand rub certified products (available in pharmacy and Lavit is non EN1500 certified and available in supermarkets. The two EN1500 certified products were found to be significantly superior in terms of reducing bacterial load. desderman pure gel, Sterillium and Lavit reduced the bacterial count to 6.4%, 8.2% and 28.0% respectively. After education in the correct use of each hand rub, the bacterial load was reduced even further, demonstrating the value of education in improving hand hygiene. Information about the testers' perceptions of the three sanitizers, together with their expectations of a hand sanitizer was obtained through a questionnaire. Efficacy, followed by skin compatibility were found to be the two most important attributes of a hand disinfectant in our target group.

Associative and Lie deformations of Poisson algebras

OpenAIRE

Remm, Elisabeth

2011-01-01

Considering a Poisson algebra as a non associative algebra satisfying the Markl-Remm identity, we study deformations of Poisson algebras as deformations of this non associative algebra. This gives a natural interpretation of deformations which preserves the underlying associative structure and we study deformations which preserve the underlying Lie algebra.

In a demanding task, three-handed manipulation is preferred to two-handed manipulation.

Science.gov (United States)

Abdi, Elahe; Burdet, Etienne; Bouri, Mohamed; Himidan, Sharifa; Bleuler, Hannes

2016-02-25

Equipped with a third hand under their direct control, surgeons may be able to perform certain surgical interventions alone; this would reduce the need for a human assistant and related coordination difficulties. However, does human performance improve with three hands compared to two hands? To evaluate this possibility, we carried out a behavioural study on the performance of naive adults catching objects with three virtual hands controlled by their two hands and right foot. The subjects could successfully control the virtual hands in a few trials. With this control strategy, the workspace of the hands was inversely correlated with the task velocity. The comparison of performance between the three and two hands control revealed no significant difference of success in catching falling objects and in average effort during the tasks. Subjects preferred the three handed control strategy, found it easier, with less physical and mental burden. Although the coordination of the foot with the natural hands increased trial after trial, about two minutes of practice was not sufficient to develop a sense of ownership towards the third arm.

Deformation Models Tracking, Animation and Applications

CERN Document Server

Torres, Arnau; Gómez, Javier

2013-01-01

The computational modelling of deformations has been actively studied for the last thirty years. This is mainly due to its large range of applications that include computer animation, medical imaging, shape estimation, face deformation as well as other parts of the human body, and object tracking. In addition, these advances have been supported by the evolution of computer processing capabilities, enabling realism in a more sophisticated way. This book encompasses relevant works of expert researchers in the field of deformation models and their applications.  The book is divided into two main parts. The first part presents recent object deformation techniques from the point of view of computer graphics and computer animation. The second part of this book presents six works that study deformations from a computer vision point of view with a common characteristic: deformations are applied in real world applications. The primary audience for this work are researchers from different multidisciplinary fields, s...

Mapping ground surface deformation using temporarily coherent point SAR interferometry: Application to Los Angeles Basin

Science.gov (United States)

Zhang, L.; Lu, Zhong; Ding, X.; Jung, H.-S.; Feng, G.; Lee, C.-W.

2012-01-01

Multi-temporal interferometric synthetic aperture radar (InSAR) is an effective tool to detect long-term seismotectonic motions by reducing the atmospheric artifacts, thereby providing more precise deformation signal. The commonly used approaches such as persistent scatterer InSAR (PSInSAR) and small baseline subset (SBAS) algorithms need to resolve the phase ambiguities in interferogram stacks either by searching a predefined solution space or by sparse phase unwrapping methods; however the efficiency and the success of phase unwrapping cannot be guaranteed. We present here an alternative approach – temporarily coherent point (TCP) InSAR (TCPInSAR) – to estimate the long term deformation rate without the need of phase unwrapping. The proposed approach has a series of innovations including TCP identification, TCP network and TCP least squares estimator. We apply the proposed method to the Los Angeles Basin in southern California where structurally active faults are believed capable of generating damaging earthquakes. The analysis is based on 55 interferograms from 32 ERS-1/2 images acquired during Oct. 1995 and Dec. 2000. To evaluate the performance of TCPInSAR on a small set of observations, a test with half of interferometric pairs is also performed. The retrieved TCPInSAR measurements have been validated by a comparison with GPS observations from Southern California Integrated GPS Network. Our result presents a similar deformation pattern as shown in past InSAR studies but with a smaller average standard deviation (4.6 mm) compared with GPS observations, indicating that TCPInSAR is a promising alternative for efficiently mapping ground deformation even from a relatively smaller set of interferograms.