ALT-II armor tile design for upgraded TEXTOR operation

International Nuclear Information System (INIS)

Newberry, B.L.; McGrath, R.T.; Watson, R.D.; Kohlhaas, W.; Finken, K.H.

1994-01-01

The upgrade of the TEXTOR tokamak at KFA Juelich was recently completed. This upgrade extended the TEXTOR pulse length from 5 seconds to 10 seconds. The auxiliary heating was increased to a total of 8.0 MW through a combination of neutral beam injection and radio frequency heating. Originally, the inertially cooled armor tiles of the full toroidal belt Advanced Limiter Test -- II (ALT-II) were designed for a 5-second operation with total heating of 6.0 MW. The upgrade of TEXTOR will increase the energy deposited per pulse onto the ALT-II by about 300%. Consequently, the graphite armor tiles for the ALT-II had to be redesigned to avoid excessively high graphite armor surface temperatures that would lead to unacceptable contamination of the plasma. This redesign took the form of two major changes in the ALT-II armor tile geometry. The first design change was an increase of the armor tile thermal mass, primarily by increasing the radial thickness of each tile from 17 mm to 20 mm. This increase in the radial tile dimension reduces the overall pumping efficiency of the ALT-II pump limiter by about 30%. The reduction in exhaust efficiency is unfortunate, but could be avoided only by active cooling of the ALT-II armor tiles. The active cooling option was too complicated and expensive to be considered at this time. The second design change involved redefining the plasma facing surface of each armor tile in order to fully utilize the entire surface area. The incident charged particle heat flux was distributed uniformly over the armor tile surfaces by carefully matching the radial, poloidal and toroidal curvature of each tile to the plasma flow in the TEXTOR boundary layer. This geometry redefinition complicates the manufacturing of the armor tiles, but results in significant thermal performance gains. In addition to these geometry upgrades, several material options were analyzed and evaluated

Joining of Tungsten Armor Using Functional Gradients

International Nuclear Information System (INIS)

John Scott O'Dell

2006-01-01

The joining of low thermal expansion armor materials such as tungsten to high thermal expansion heat sink materials has been a major problem in plasma facing component (PFC) development. Conventional planar bonding techniques have been unable to withstand the high thermal induced stresses resulting from fabrication and high heat flux testing. During this investigation, innovative functional gradient joints produced using vacuum plasma spray forming techniques have been developed for joining tungsten armor to copper alloy heat sinks. A model was developed to select the optimum gradient architecture. Based on the modeling effort, a 2mm copper rich gradient was selected. Vacuum plasma pray parameters and procedures were then developed to produce the functional gradient joint. Using these techniques, dual cooling channel, medium scale mockups (32mm wide x 400mm length) were produced with vacuum plasma spray formed tungsten armor. The thickness of the tungsten armor was up to 5mm thick. No evidence of debonding at the interface between the heat sink and the vacuum plasma sprayed material was observed.

Improved Shaped Charge Armors

National Research Council Canada - National Science Library

Vodenicharov, Stefan

2003-01-01

.... The major activities that are carried out are design, fabrication and testing in proving ground conditions of armor samples of various characteristics, electron microscopic and X-ray structural...

Glass matrix armor

International Nuclear Information System (INIS)

Calkins, N.C.

1991-01-01

This patent describes an armor system which utilizes glass. A plurality of constraint cells are mounted on a surface of a substrate, which is metal armor plate or a similar tough material, such that the cells almost completely cover the surface of the substrate. Each constraint cell has a projectile receiving wall parallel to the substrate surface and has sides which are perpendicular to and surround the perimeter of the receiving wall. The cells are mounted such that, in one embodiment, the substrate surface serves as a sixth side or closure for each cell. Each cell has inside of it a plate, termed the front plate, which is parallel to and in contact with substantially all of the insides surface of the receiving wall. The balance of each cell is completely filled with a projectile-abrading material consisting of glass and a ceramic material and, in certain embodiments, a polymeric material

A Workshop for Planning the Efficient Transfer of Recent Ceramic Armor/Antiarmor Modeling Results to the Armor Design Community: Summary and Draft Plan

National Research Council Canada - National Science Library

Klopp, Richard

1999-01-01

In the mid-1980s DARPA began sponsoring several programs to develop ceramic armor for heavy armor applications, supported by DARPA and ARO funded technology base initiatives in modeling, experiments...

Armor breakup and reformation in a degradational laboratory experiment

OpenAIRE

Orrú, Clara; Blom, Astrid; Uijttewaal, Wim S. J.

2016-01-01

Armor breakup and reformation was studied in a laboratory experiment using a trimodal mixture composed of a 1mm sand fraction and two gravel fractions (6 and 10mm). The initial bed was characterized by a stepwise downstream fining pattern (trimodal reach) and a downstream sand reach, and the experiment was conducted under conditions without sediment supply. In the initial stage of the experiment an armor formed over the trimodal reach. The formation of the armor under partial transport condit...

Analysis of Terminal Metallic Armor Plate Free-Surface Bulging

National Research Council Canada - National Science Library

Rapacki, Jr, E. J

2008-01-01

An analysis of the bulge formed on the free-surface of the terminal metallic plate of an armor array is shown to lead to reasonable estimates of the armor array's remaining penetration/perforation resistance...

Negligible heat strain in armored vehicle officers wearing personal body armor

Directory of Open Access Journals (Sweden)

Hunt Andrew P

2011-07-01

Full Text Available Abstract Objectives This study evaluated the heat strain experienced by armored vehicle officers (AVOs wearing personal body armor (PBA in a sub-tropical climate. Methods Twelve male AVOs, aged 35-58 years, undertook an eight hour shift while wearing PBA. Heart rate and core temperature were monitored continuously. Urine specific gravity (USG was measured before and after, and with any urination during the shift. Results Heart rate indicated an intermittent and low-intensity nature of the work. USG revealed six AVOs were dehydrated from pre through post shift, and two others became dehydrated. Core temperature averaged 37.4 ± 0.3°C, with maximum's of 37.7 ± 0.2°C. Conclusions Despite increased age, body mass, and poor hydration practices, and Wet-Bulb Globe Temperatures in excess of 30°C; the intermittent nature and low intensity of the work prevented excessive heat strain from developing.

Development of the armoring technique for ITER Divertor Dome

Energy Technology Data Exchange (ETDEWEB)

Litunovsky, Nikolay, E-mail: nlitunovsky@sintez.niiefa.spb.su [D.V. Efremov Reseasch Institute, 3, Doroga na Metallostroy, Saint Petersburg (Russian Federation); Alekseenko, Evgeny; Makhankov, Alexey; Mazul, Igor [D.V. Efremov Reseasch Institute, 3, Doroga na Metallostroy, Saint Petersburg (Russian Federation)

2011-10-15

This paper describes the current status of the technique for armoring of Plasma Facing Units (PFUs) of the ITER Divertor Dome with flat tungsten tiles planned for application at the procurement stage. Application of high-temperature vacuum brazing for armoring of High Heat Flux (HHF) plasma facing components was traditionally developed at the Efremov Institute and successfully tried out at the ITER R and D stage by manufacturing and HHF testing of a number of W- and Be-armored mock-ups . Nevertheless, the so-called 'fast brazing' technique successfully applied in the past was abandoned at the stage of manufacturing of the Dome Qualification Prototypes (Dome QPs), as it failed to retain the mechanical properties of CuCrZr heat sink of the substrate. Another problem was a substantially increased number of armoring tiles brazed onto one substrate. Severe ITER requirements for the joints quality have forced us to refuse from production of W/Cu joints by brazing in favor of casting. These modifications have allowed us to produce ITER Divertor Dome QPs with high-quality tungsten armor, which then passed successfully the HHF testing. Further preparation to the procurement stage is in progress.

Humvee Armor Plate Drilling

National Research Council Canada - National Science Library

2004-01-01

When drilling holes in hard steel plate used in up-armor kits for Humvee light trucks, the Anniston Army Depot, Anniston, Alabama, requested the assistance of the National Center for Defense Manufacturing and Machining (NCDMM...

The Armored Infantry in the US Force Structure.

Science.gov (United States)

1985-12-02

armored infantry and tank integration occurred during the capture of the town of Troyes , France, in 1944, by Task Force West of the 4th Armored...Singling and Troyes . The same can not be said of the foot infantryman because normally he was not associated with tanks. Such was the case in the previously

Analysis of behind the armor ballistic trauma.

Science.gov (United States)

Wen, Yaoke; Xu, Cheng; Wang, Shu; Batra, R C

2015-05-01

The impact response of body armor composed of a ceramic plate with an ultrahigh molecular weight polyethylene (UHMWPE) fiber-reinforced composite and layers of UHMWPE fibers shielding a block of ballistic gelatin has been experimentally and numerically analyzed. It is a surrogate model for studying injuries to human torso caused by a bullet striking body protection armor placed on a person. Photographs taken with a high speed camera are used to determine deformations of the armor and the gelatin. The maximum depth of the temporary cavity formed in the ballistic gelatin and the peak pressure 40mm behind the center of the gelatin front face contacting the armor are found to be, respectively, ~34mm and ~15MPa. The Johnson-Holmquist material model has been used to simulate deformations and failure of the ceramic. The UHMWPE fiber-reinforced composite and the UHMWPE fiber layers are modeled as linear elastic orthotropic materials. The gelatin is modeled as a strain-rate dependent hyperelastic material. Values of material parameters are taken from the open literature. The computed evolution of the temporary cavity formed in the gelatin is found to qualitatively agree with that seen in experiments. Furthermore, the computed time histories of the average pressure at four points in the gelatin agree with the corresponding experimentally measured ones. The maximum pressure at a point and the depth of the temporary cavity formed in the gelatin can be taken as measures of the severity of the bodily injury caused by the impact; e.g. see the United States National Institute of Justice standard 0101.06-Ballistic Resistance of Body Armor. Copyright © 2015 Elsevier Ltd. All rights reserved.

Performance of the PDX neutral beam wall armor

International Nuclear Information System (INIS)

Kugel, H.W.; Eubank, H.P.; Kozub, T.A.; Williams, M.D.

1985-02-01

The PDX wall armor was designed to function as an inner wall thermal armor, a neutral beam diagnostic, and a large area inner toroidal plasma limiter. In this paper we discuss its thermal performance as wall armor during two years of PDX neutral beam heating experiments. During this period it provided sufficient inner wall protection to permit perpendicular heating injections into normal and disruptive plasmas as well as injections in the absence of plasma involving special experiments, calibrations, and tests important for the optimization and development of the PDX neutral beam injection system. Many of the design constraints and performance issues encountered in this work are relevant to the design of larger fusion devices

50 Div in Normandy: A Critical Analysis of the British 50th (Northumbrian) Division on D-Day and in the Battle of Normandy

National Research Council Canada - National Science Library

Williams, Ethan R

2007-01-01

In late 1943, the British Army ordered the veteran 7th Armored, 51st (Highland) and 50th (Northumbrian) Divisions to return to Great Britain to provide combat experienced troops for the D-Day invasion of northwest Europe...

ALT-II armor tile design for upgraded TEXTOR operation

International Nuclear Information System (INIS)

Newberry, B.L.; McGrath, R.T.; Watson, R.D.

1994-01-01

The upgrade of the TEXTOR tokamak at KFA Julich will be completed in the spring of 1994. The upgrade will extend the TEXTOR pulse length from 5 seconds to 10 seconds. The auxiliary heating systems are also scheduled to be upgraded so that eventually a total of 8.0 MW auxiliary heating will be available through a combination of neutral beam injection and radio frequency heating. Originally, the inertially cooled armor tiles on the full toroidal belt Advanced Limiter Test - II (ALT-II) were designed for 5-second operation with a total heating power of 6.0 MW. The upgrade of TEXTOR will increase the energy deposited per pulse onto ALT-II by more than 300%. Consequently, the graphite armor tiles for ALT-II had to be redesigned in order to increase their thermal inertia and, thereby, avoid excessively high graphite armor surface temperatures that would lead to unacceptable contamination of the plasma. The armor tile thermal inertia had been increase primarily by expanding the radial thickness of the tiles from 17 mm to 20 mm. This increase in radial tile dimension will reduce the overall pumping efficiency of the ALT-II pump limiter by about 30%. The final armor tile design was a compromise between increasing the power handling capability and reducing the particle exhaust efficiency of ALT-II. The reduction in exhaust efficiency is unfortunate, but could only be avoided by active cooling of the ALT-II armor tiles. The active cooling option was too complicated and expensive to be considered at this time

76 FR 70165 - Ballistic-Resistant Body Armor Standard Workshop

Science.gov (United States)

2011-11-10

... DEPARTMENT OF JUSTICE Office of Justice Programs [OJP (NIJ) Docket No. 1573] Ballistic-Resistant Body Armor Standard Workshop AGENCY: National Institute of Justice, DOJ. ACTION: Notice. SUMMARY: The... jointly hosting a workshop focused on NIJ Standard-0101.06, Ballistic Resistance of Body Armor, and the...

Armored Composite Ammunition Pressure Vessel

National Research Council Canada - National Science Library

Clark, William

1999-01-01

...). This ammunition containment system must not only meet environmental and handling requirements but also provide armor protection against impacting threats and reduce the response of the stowed...

Physical Training for Armor Crewmen

National Research Council Canada - National Science Library

Baker, Shane

2003-01-01

.... The author concluded that if his sample population represented the entire population then armor leaders were neglecting muscular strength, muscular endurance and flexibility in their physical readiness programs...

Design study of an armor tile handling manipulator for the Fusion Experimental Reactor

International Nuclear Information System (INIS)

Shibanuma, K.; Honda, T.; Satoh, K.; Terakado, T.; Kondoh, M.; Sasaki, N.; Munakata, T.; Murakami, S.

1991-01-01

A conceptual design of the Fusion Experimental Reactor (FER), which is a D-T burning reactor following on JT-60 in Japan, has been developed by Japan Atomic Energy Research Institute (JAERI). In FER, a rail-mounted vehicle concept is planned to be adopted for in-vessel maintenance, such as maintenance of divertor plates and armor tiles. Advantages of this concept are the high stiffness of the rail as a base structure for maintenance and the high mobility of the vehicle along the rail. Twin armor tile handling manipulators installed on both sides of the vehicle have been designed. The respective manipulators for armor tile handling have 8 degrees of freedom in order to have access to any place of the first wall and to go through the horizontal port by operating manipulator joints. If the two types of manipulators for divertor plates and armor tiles are installed on the vehicle and the divertor handling manipulator carries a case filled with armor tiles, the replacement time of armor tiles will be reduced. In FER, moreover, maintenance of armor tiles, which is a scheduled maintenance, is planned to be carried out by the autonomous control using position sensors etc. In order to accumulate the data base for the development of the autonomous control of the manipulator in armor tile maintenance, the present paper describes basic mechanical characteristics (stress, deflection and natural frequency) of the armor tile handling manipulator calculated by static stress and dynamic eigenvalue analyses. (orig.)

Physical Training for Armor Crewmen

National Research Council Canada - National Science Library

Baker, Shane

2003-01-01

This thesis examines the physical requirements of armor crewmen and provides a method for training them to meet those requirements based on current Army doctrine and emerging fitness doctrine using...

Armor Plate Surface Roughness Measurements

National Research Council Canada - National Science Library

Stanton, Brian; Coburn, William; Pizzillo, Thomas J

2005-01-01

...., surface texture and coatings) that could become important at high frequency. We measure waviness and roughness of various plates to know the parameter range for smooth aluminum and rolled homogenous armor (RHA...

Transparent Armor Cost Benefit Study

National Research Council Canada - National Science Library

Prokurat Franks, Lisa; Holm, David; Barnak, Rick

2006-01-01

...; the increase in demand for transparent gun shields in Operation Iraqi Freedom (OIF) and early versions of jerry-rigged shields used in OIF, including Pope glass and Transparent Armored Gun Shields (TAGS...

Quantifying the effectiveness of shoreline armoring removal on coastal biota of Puget Sound.

Science.gov (United States)

Lee, Timothy S; Toft, Jason D; Cordell, Jeffery R; Dethier, Megan N; Adams, Jeffrey W; Kelly, Ryan P

2018-01-01

Shoreline armoring is prevalent around the world with unprecedented human population growth and urbanization along coastal habitats. Armoring structures, such as riprap and bulkheads, that are built to prevent beach erosion and protect coastal infrastructure from storms and flooding can cause deterioration of habitats for migratory fish species, disrupt aquatic-terrestrial connectivity, and reduce overall coastal ecosystem health. Relative to armored shorelines, natural shorelines retain valuable habitats for macroinvertebrates and other coastal biota. One question is whether the impacts of armoring are reversible, allowing restoration via armoring removal and related actions of sediment nourishment and replanting of native riparian vegetation. Armoring removal is targeted as a viable option for restoring some habitat functions, but few assessments of coastal biota response exist. Here, we use opportunistic sampling of pre- and post-restoration data for five biotic measures (wrack % cover, saltmarsh % cover, number of logs, and macroinvertebrate abundance and richness) from a set of six restored sites in Puget Sound, WA, USA. This broad suite of ecosystem metrics responded strongly and positively to armor removal, and these results were evident after less than one year. Restoration responses remained positive and statistically significant across different shoreline elevations and temporal trajectories. This analysis shows that removing shoreline armoring is effective for restoration projects aimed at improving the health and productivity of coastal ecosystems, and these results may be widely applicable.

Quantifying the effectiveness of shoreline armoring removal on coastal biota of Puget Sound

Directory of Open Access Journals (Sweden)

Timothy S. Lee

2018-02-01

Full Text Available Shoreline armoring is prevalent around the world with unprecedented human population growth and urbanization along coastal habitats. Armoring structures, such as riprap and bulkheads, that are built to prevent beach erosion and protect coastal infrastructure from storms and flooding can cause deterioration of habitats for migratory fish species, disrupt aquatic–terrestrial connectivity, and reduce overall coastal ecosystem health. Relative to armored shorelines, natural shorelines retain valuable habitats for macroinvertebrates and other coastal biota. One question is whether the impacts of armoring are reversible, allowing restoration via armoring removal and related actions of sediment nourishment and replanting of native riparian vegetation. Armoring removal is targeted as a viable option for restoring some habitat functions, but few assessments of coastal biota response exist. Here, we use opportunistic sampling of pre- and post-restoration data for five biotic measures (wrack % cover, saltmarsh % cover, number of logs, and macroinvertebrate abundance and richness from a set of six restored sites in Puget Sound, WA, USA. This broad suite of ecosystem metrics responded strongly and positively to armor removal, and these results were evident after less than one year. Restoration responses remained positive and statistically significant across different shoreline elevations and temporal trajectories. This analysis shows that removing shoreline armoring is effective for restoration projects aimed at improving the health and productivity of coastal ecosystems, and these results may be widely applicable.

Magnetic non-destructive evaluation of ruptures of tensile armor in oil risers

International Nuclear Information System (INIS)

Pérez-Benitez, J A; Padovese, L R

2012-01-01

Risers are flexible multilayered pipes formed by an inner flexible metal structure surrounded by polymer layers and spiral wound steel ligaments, also known as armor wires. Since these risers are used to link subsea pipelines to floating oil and gas production installations, and their failure could produce catastrophic consequences, some methods have been proposed to monitor the armor integrity. However, until now there is no practical method that allows the automatic non-destructive detection of individual armor wire rupture. In this work we show a method using magnetic Barkhausen noise that has shown high efficiency in the detection of armor wire rupture. The results are examined under the cyclic and static load conditions of the riser. This work also analyzes the theory behind the singular dependence of the magnetic Barkhausen noise on the applied tension in riser armor wires. (paper)

Transparent ceramics for armor and EM window applications

OpenAIRE

Patel, Parimal J.; Gilde, Gary A.; Dehmer, Peter G.; McCauley, James W.

2000-01-01

Recently, the U.S. Army Research Laboratory (ARL) has focused increased attention on the development of transparent armor material systems for a variety of applications. Future combat and non-combat environments will require lightweight, threat adjustable, multifunctional, and affordable armor. Current glass/polycarbonate technologies are not expected to meet the increased requirements. Results over the past few years indicate that the use of transparent crystalline ceramics greatly improve t...

27 CFR 478.148 - Armor piercing ammunition intended for sporting or industrial purposes.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2010-04-01 2010-04-01 false Armor piercing ammunition... AMMUNITION COMMERCE IN FIREARMS AND AMMUNITION Exemptions, Seizures, and Forfeitures § 478.148 Armor piercing ammunition intended for sporting or industrial purposes. The Director may exempt certain armor piercing...

Armored garment for protecting

Science.gov (United States)

Purvis, James W [Albuquerque, NM; Jones, II, Jack F.; Whinery, Larry D [Albuquerque, NM; Brazfield, Richard [Albuquerque, NM; Lawrie, Catherine [Tijeras, NM; Lawrie, David [Tijeras, NM; Preece, Dale S [Watkins, CO

2009-08-11

A lightweight, armored protective garment for protecting an arm or leg from blast superheated gases, blast overpressure shock, shrapnel, and spall from a explosive device, such as a Rocket Propelled Grenade (RPG) or a roadside Improvised Explosive Device (IED). The garment has a ballistic sleeve made of a ballistic fabric, such as an aramid fiber (e.g., KEVLAR.RTM.) cloth, that prevents thermal burns from the blast superheated gases, while providing some protection from fragments. Additionally, the garment has two or more rigid armor inserts that cover the upper and lower arm and protect against high-velocity projectiles, shrapnel and spall. The rigid inserts can be made of multiple plies of a carbon/epoxy composite laminate. The combination of 6 layers of KEVLAR.RTM. fabric and 28 plies of carbon/epoxy laminate inserts (with the inserts being sandwiched in-between the KEVLAR.RTM. layers), can meet the level IIIA fragmentation minimum V.sub.50 requirements for the US Interceptor Outer Tactical Vest.

’Stinger under Armor:’ An Analysis of Alternatives

Science.gov (United States)

1990-01-01

This paper examines a concept for employment of the Stinger Air Defense Artillery weapon system known as ’Stinger under Armor .’ It traces the...areas air defense in the pre-FAADS era. This broader deficiency ultimately drove the need for ’Stinger under Armor ’ as a short-term solution to a current battlefield vulnerability.

Ballistic protection performance of curved armor systems with or without debondings/delaminations

International Nuclear Information System (INIS)

Tan, Ping

2014-01-01

Highlights: • Influence of pre-existing defect in an armor system on its ballistic performance. • Development of finite element models for the ballistic performance of armor systems. • Prediction of the ballistic limit and back face deformation of curved armor systems. - Abstract: In order to discern how pre-existing defects such as single or multiple debondings/delaminations in a curved armor system may affect its ballistic protection performance, two-dimensional axial finite element models were generated using the commercial software ANSYS/Autodyn. The armor systems considered in this investigation are composed of boron carbide front component and Kevlar/epoxy backing component. They are assumed to be perfectly bonded at the interface without defects. The parametric study shows that for the cases considered, the maximum back face deformation of a curved armor system with or without defects is more sensitive to its curvature, material properties of the ceramic front component, and pre-existing defect size and location than the ballistic limit velocity. Additionally, both the ballistic limit velocity and maximum back face deformation are significantly affected by the backing component thickness, front/backing component thickness ratio and the number of delaminations

Blast-Resistant Improvement of Sandwich Armor Structure with Aluminum Foam Composite

OpenAIRE

Yang, Shu; Qi, Chang

2013-01-01

Sandwich armor structures with aluminum foam can be utilized to protect a military vehicle from harmful blast load such as a landmine explosion. In this paper, a system-level dynamic finite element model is developed to simulate the blast event and to evaluate the blast-resistant performance of the sandwich armor structure. It is found that a sandwich armor structure with only aluminum foam is capable of mitigating crew injuries under a moderate blast load. However, a severe blast load causes...

Armoring confined bubbles in concentrated colloidal suspensions

Science.gov (United States)

Yu, Yingxian; Khodaparast, Sepideh; Stone, Howard

2016-11-01

Encapsulation of a bubble with microparticles is known to significantly improve the stability of the bubble. This phenomenon has recently gained increasing attention due to its application in a variety of technologies such as foam stabilization, drug encapsulation and colloidosomes. Nevertheless, the production of such colloidal armored bubble with controlled size and particle coverage ratio is still a great challenge industrially. We study the coating process of a long air bubble by microparticles in a circular tube filled with a concentrated microparticles colloidal suspension. As the bubble proceeds in the suspension of particles, a monolayer of micro-particles forms on the interface of the bubble, which eventually results in a fully armored bubble. We investigate the phenomenon that triggers and controls the evolution of the particle accumulation on the bubble interface. Moreover, we examine the effects of the mean flow velocity, the size of the colloids and concentration of the suspension on the dynamics of the armored bubble. The results of this study can potentially be applied to production of particle-encapsulated bubbles, surface-cleaning techniques, and gas-assisted injection molding.

Ballistic Application of Coir Fiber Reinforced Epoxy Composite in Multilayered Armor

OpenAIRE

Luz, Fernanda Santos da; Monteiro, Sergio Neves; Lima, Eduardo Sousa; Lima Júnior, Édio Pereira

2017-01-01

Multilayered armor systems (MAS) composed of relatively lighter materials with capacity to provide personal ballistic protection are being extensively investigated and used in armor vests. A typical MAS to stand high impact energy 7.62 mm bullet has a front ceramic followed by an aramid fabric laminate, such as Kevlar™. Since both the army and municipal police personnel might need to wear an armor vest, a large number of vests needs to be supplied. In the case of Kevlar™, one of the most expe...

77 FR 39259 - Agency Information Collection Activities; Proposed Collection; Comments Requested: Body Armor in...

Science.gov (United States)

2012-07-02

...: Establishment survey and initial approval of collection. (2) Title of Form/Collection: Body Armor in Correctional Institutions Survey. The collections include the forms Body Armor Administrative Agency-Level Survey and Body Armor Individual-level Correctional Officer Survey. (3) Agency form number, if any, and...

77 FR 22345 - Agency Information Collection Activities: Proposed Collection; Comments Requested; Body Armor in...

Science.gov (United States)

2012-04-13

... Collection: Establishment survey and initial approval of collection. (2) Title of Form/Collection: Body Armor... Agency-Level Survey and Body Armor Individual-level Correctional Officer Survey. (3) Agency form number... approaches to overcome those barriers. (a) For the Body Armor Administrative Agency-Level Survey, the chief...

7 CFR 1755.406 - Shield or armor ground resistance measurements.

Science.gov (United States)

2010-01-01

...) The insulation resistance test set should have an output voltage not to exceed 500 volts dc and may be... 7 Agriculture 11 2010-01-01 2010-01-01 false Shield or armor ground resistance measurements. 1755... MATERIALS, AND STANDARD CONTRACT FORMS § 1755.406 Shield or armor ground resistance measurements. (a) Shield...

Engineering model for body armor

NARCIS (Netherlands)

Roebroeks, G.H.J.J.; Carton, E.P.

2014-01-01

TNO has developed an engineering model for flexible body armor, as one of their energy based engineering models that describe the physics of projectile to target interactions (weaves, metals, ceramics). These models form the basis for exploring the possibilities for protection improvement. This

Imperfection analysis of flexible pipe armor wires in compression and bending

DEFF Research Database (Denmark)

Østergaard, Niels Højen; Lyckegaard, Anders; Andreasen, Jens H.

2012-01-01

The work presented in this paper is motivated by a specific failure mode known as lateral wire buckling occurring in the tensile armor layers of flexible pipes. The tensile armor is usually constituted by two layers of initially helically wound steel wires with opposite lay directions. During pipe...... ability of the wires. This may cause the wires to buckle in the circumferential pipe direction, when these are restrained against radial deformations by adjacent layers. In the present paper, a single armoring wire modeled as a long and slender curved beam embedded in a frictionless cylinder bent...

Expanding the Availability of Lightweight Aluminum Alloy Armor Plate Procured from Detailed Military Specifications

Science.gov (United States)

Doherty, Kevin; Squillacioti, Richard; Cheeseman, Bryan; Placzankis, Brian; Gallardy, Denver

For many years, the range of aluminum alloys for armor plate applications obtainable in accordance with detailed military specifications was very limited. However, the development of improved aluminum alloys for aerospace and other applications has provided an opportunity to modernize the Army portfolio for ground vehicle armor applications. While the benefits of offering additional alloy choices to vehicle designers is obvious, the process of creating detailed military specifications for armor plate applications is not trivial. A significant amount of material and testing is required to develop the details required by an armor plate specification. Due to the vast number of material programs that require standardization and with a limited amount of manpower and funds as a result of Standardization Reform in 1995, one typically requires a need statement from a vehicle program office to justify and sponsor the work. This presentation will focus on recent aluminum alloy armor plate specifications that have added capability to vehicle designers' selection of armor materials that offer possible benefits such as lower cost, higher strength, better ballistic and corrosion resistance, improved weldability, etc.

Mosaic Transparent Armor System Final Report CRADA No. TC02162.0

Energy Technology Data Exchange (ETDEWEB)

Kuntz, J. D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Breslin, M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2017-08-29

This was a collaborative effort between Lawrence Livermore National Security, LLC as manager and operator of Lawrence Livermore National Laboratory (LLNL) and The Protective Group, Inc. (TPG) to improve the performance of the mosaic transparent armor system (MTAS) for transparent armor applications, military and civilian. LLNL was to provide the unique MTAS technology and designs to TPG for innovative construction and ballistic testing of improvements needed for current and near future application of the armor windows on vehicles and aircraft. The goal of the project was to advance the technology of MTAS to the point that these mosaic transparent windows would be introduced and commercially manufactured for military vehicles and aircraft.

Embedded Fiber Optic Sensors for Integral Armor

National Research Council Canada - National Science Library

Fink, Bruce

2000-01-01

This report describes the work performed with Production Products Manufacturing & Sales (PPMS), Inc., under the "Liquid Molded Composite Armor Smart Structures Using Embedded Sensors" Small Business Innovative Research...

Patterned Armor Performance Evaluation for Multiple Impacts

National Research Council Canada - National Science Library

De

2003-01-01

.... Performance characteristics of an ideal patterned armor with respect to multiple hits are discussed, and the types of single-shot ballistic data needed to quantify that performance are presented...

Armor in Vietnam

Science.gov (United States)

1976-05-01

battles a-Riuot the insurgent enemy, especially with armor. French contingents were present in Tndo Chinh P-w early as 1852, but it was not until 1884...committed to Vietnam were straight infantry. These troons er•A tran -norted in hn4±{ copters and usually airlifted to the battle zone; however, once...0STAINf0 FROM VKTNAM NATIONAL MAP SERVICE (NOS) PHU-YEN OCTOBER 19665 OARLAC ......... KKAN1+ HOA QLWA- DUC TUYEN- DUC PHUOC- NINH_ C;ry OF -10 T CAM RANK TAY

Computed tomography of the ''armored brain''

International Nuclear Information System (INIS)

Ludwig, B.; Nix, W.; Lanksch, W.

1983-01-01

A classified chronic subdural hematoma may cover the surface of the cerebral hemispheres to such an extent that one can talk of an ''armored brain''. Pathogenesis, clinical course and treatment are discussed based on the computed tomograms of five cases. (orig.)

Report to the Attorney General on Body Armor Safety Initiative Testing and Activities

National Research Council Canada - National Science Library

2005-01-01

On November 17, 2003, Attorney General John Ashcroft announced the U.S. Department of Justice's Body Armor Safety Initiative in response to concerns from the law enforcement community regarding the effectiveness of body armor in use...

Effect of surface texture and structure on the development of stable fluvial armors

Science.gov (United States)

Bertin, Stephane; Friedrich, Heide

2018-04-01

Stable fluvial armors are found in river systems under conditions of partial sediment transport and limited sediment supply, a common occurrence in nature. Stable armoring is also readily recreated in experimental flumes. Initially, this bed stabilizing phenomenon was examined for different flow discharges and solely related to surface coarsening and bedload transport reduction. The models developed suggest a specific armor composition (i.e., texture) dependent on the parent bed material and formative discharge. Following developments in topographic remote sensing, recent research suggests that armor structure is an important control on bed stability and roughness. In this paper, replicated flume runs during which digital elevation models (DEMs) were collected from both exposed and flooded gravel beds are used to interpret armoring manifestations and to assess their replicability. A range of methodologies was used for the analysis, providing information on (i) surface grain size and orientation, (ii) bed-elevation distributions, (iii) the spatial coherence of the elevations at the grain-scale, (iv) surface slope and aspect, (v) grain imbrication and (vi) the spatial variability in DEM properties. The bed-surface topography was found to be more responsive than bed-material size to changes in flow strength. Our experimental results also provide convincing evidence that gravel-beds' response to water-work during parallel degradation is unique (i.e., replicable) given the formative parameters. Based on this finding, relationships between the armors' properties and formative parameters are proposed, and are supported by adding extensive data from previous research.

Functional trade-off between strength and thermal capacity of dermal armor: Insights from girdled lizards.

Science.gov (United States)

Broeckhoven, Chris; du Plessis, Anton; Hui, Cang

2017-10-01

The presence of dermal armor is often unambiguously considered the result of an evolutionary predator-prey arms-race. Recent studies focusing predominantly on osteoderms - mineralized elements embedded in the dermis layer of various extant and extinct vertebrates - have instead proposed that dermal armor might exhibit additional functionalities besides protection. Multiple divergent functionalities could impose conflicting demands on a phenotype, yet, functional trade-offs in dermal armor have rarely been investigated. Here, we use high-resolution micro-computed tomography and voxel-based simulations to test for a trade-off between the strength and thermal capacity of osteoderms using two armored cordylid lizards as model organisms. We demonstrate that high vascularization, associated with improved thermal capacity might limit the strength of osteoderms. These results call for a holistic, cautionary future approach to studies investigating dermal armor, especially those aiming to inspire artificial protective materials. Copyright © 2017 Elsevier Ltd. All rights reserved.

A numerical study on the disturbance of explosive reactive armors to jet penetration

Directory of Open Access Journals (Sweden)

Xiang-dong Li

2014-03-01

Full Text Available The disturbance of flat and V-shaped sandwich reactive armor configurations to shaped-charge jet is studied by a numerical approach. The disturbing and cutting effects of the two reactive armor configurations to the jet are successfully captured. The predicted disturbance characteristics and patterns are in fairly good agreement with the X-ray photographic observations. The residual depth of penetration into a semi-infinitive homogeneous steel target behind the reactive armor is computed for a series of jet/armor parameters. For the flat configuration, it is demonstrated that the residual penetration depth is not significantly reduced for a normal impact while it is reduced up to 75% for an oblique impact. In comparison, the V-shaped configuration reduces the penetration depth of the jet to 90%, and it is observed that the penetration depth is not sensitive to the V-shaped angle.

Acquisition of the Armored Medical Evacuation Vehicle

National Research Council Canada - National Science Library

2000-01-01

.... The platform for the AMEV is an upgraded M2A0 Bradley Fighting Vehicle variant, which has the turret removed, the roof squared off and raised 13 inches, a 600 horsepower engine, and additional armor...

Fracture mechanical analysis of tungsten armor failure of a water-cooled divertor target

Energy Technology Data Exchange (ETDEWEB)

Li, Muyuan; Werner, Ewald [Lehrstuhl für Werkstoffkunde und Werkstoffmechanik, Technische Universität München, Boltzmannstr. 15, 85748 Garching (Germany); You, Jeong-Ha, E-mail: you@ipp.mpg.de [Max-Planck-Institut für Plasmaphysik, Boltzmannstr. 2, 85748 Garching (Germany)

2014-11-15

Highlights: • The FEM-based VCE method and XFEM were employed for computing K{sub I} (or J-integral) and predicting progressive cracking, respectively. • The most probable pattern of crack formation is radial cracking in the tungsten armor block. • The most probable site of cracking is the upper interfacial region of the tungsten armor block adjacent to the top position of the copper interlayer. • The initiation of a major crack becomes likely, only when the strength of tungsten armor block is significantly reduced from its original strength. - Abstract: The inherent brittleness of tungsten at low temperature and the embrittlement by neutron irradiation are its most critical weaknesses for fusion applications. In the current design of the ITER and DEMO divertor, the high heat flux loads during the operation impose a strong constraint on the structure–mechanical performance of the divertor. Thus, the combination of brittleness and the thermally induced stress fields due to the high heat flux loads raises a serious reliability issue in terms of the structural integrity of tungsten armor. In this study, quantitative estimates of the vulnerability of the tungsten monoblock armor cracking under stationary high heat flux loads are presented. A comparative fracture mechanical investigation has been carried out by means of two different types of computational approaches, namely, the extended finite element method (XFEM) and the finite element method (FEM)-based virtual crack tip extension (VCE) method. The fracture analysis indicates that the most probable pattern of crack formation is radial cracking in the tungsten armor starting from the interface to tube and the most probable site of cracking is the upper interfacial region of the tungsten armor adjacent to the top position of the copper interlayer. The strength threshold for crack initiation and the high heat flux load threshold for crack propagation are evaluated based on XFEM simulations and computations

27 CFR 478.149 - Armor piercing ammunition manufactured or imported for the purpose of testing or experimentation.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2010-04-01 2010-04-01 false Armor piercing ammunition... Armor piercing ammunition manufactured or imported for the purpose of testing or experimentation. The provisions of §§ 478.37 and 478.99(d) with respect to the manufacture or importation of armor piercing...

Repair of manufacturing defects in the armor of plasma facing units of the ITER Divertor Dome

International Nuclear Information System (INIS)

Litunovsky, Nikolay; Alekseenko, Evgeny; Kuznetsov, Vladimir; Lyanzberg, Dmitriy; Makhankov, Aleksey; Rulev, Roman

2013-01-01

Highlights: • Sporadic manufacturing defects in ITER Divertor Dome PFUs may be repaired. • We have developed a repair technique for ITER Divertor Dome PFUs. • Armor repair technique for ITER Divertor Dome PFUs is successfully tested. -- Abstract: The paper describes the repair procedure developed for removal of manufacturing defects occurring sporadically during armoring of plasma facing units (PFUs) of the ITER Divertor Dome. Availability of armor repair technique is prescribed by the procurement arrangement for the ITER Divertor Dome concluded in 2009 between the ITER Organization and the ITER Domestic Agency of Russia. The paper presents the detailed description of the procedure, data on its effect on the joints of the rest part of the armor and on the grain structure of the PFU heat sink. The results of thermocycling of large-scale Dome PFU mock-ups manufactured with demonstration of armor repair are also given

Repair of manufacturing defects in the armor of plasma facing units of the ITER Divertor Dome

Energy Technology Data Exchange (ETDEWEB)

Litunovsky, Nikolay, E-mail: nlitunovsky@sintez.niiefa.spb.su; Alekseenko, Evgeny; Kuznetsov, Vladimir; Lyanzberg, Dmitriy; Makhankov, Aleksey; Rulev, Roman

2013-10-15

Highlights: • Sporadic manufacturing defects in ITER Divertor Dome PFUs may be repaired. • We have developed a repair technique for ITER Divertor Dome PFUs. • Armor repair technique for ITER Divertor Dome PFUs is successfully tested. -- Abstract: The paper describes the repair procedure developed for removal of manufacturing defects occurring sporadically during armoring of plasma facing units (PFUs) of the ITER Divertor Dome. Availability of armor repair technique is prescribed by the procurement arrangement for the ITER Divertor Dome concluded in 2009 between the ITER Organization and the ITER Domestic Agency of Russia. The paper presents the detailed description of the procedure, data on its effect on the joints of the rest part of the armor and on the grain structure of the PFU heat sink. The results of thermocycling of large-scale Dome PFU mock-ups manufactured with demonstration of armor repair are also given.

Numerical simulations of semi-armor-piercing warhead penetrating aircraft carrier target

OpenAIRE

Dong Sangqaing; Cai Xinghui; Wang Guoliang; Gao Yunliang; Lu Jiangren

2015-01-01

FEM models of semi-armor-piercing warhead penetrating aircraft carrier deck are established, which are validated by related experimental data. Base on the models, the process of semi-armor-piercing warhead penetrating aircraft carrier deck with different incidence angles and attack angles are carried out. The results show that incidence angles have no remarkable influence on penetration capability of the projectile under the circumstance of zero attack angle. Ductility reaming damage mode and...

Preparing soft-bodied arthropods for arthropods for microscope examination: Armored Scales (Insects: Hemiptera: Diaspididae)

Science.gov (United States)

Proper identification of armored scales (Hemiptera: Diaspididae) requires preparation of the specimen on a microscope slide. This training video provides visual instruction on how to prepare armored scales specimens on microscope slides for examination and identification. Steps ranging from collect...

Dragon Skin - How It Changed Body Armor Testing in the United States Army

Science.gov (United States)

2015-09-01

members of this committee who have their kids at one time or another wearing body armor in theater, either Iraq or Afghanistan. And that includes... YouTube has pictures of Dragon Skin body armor testing on the Internet and Wikipedia has posted a carefully documented description of the history of

Production and characterization of ceramics for armor application

International Nuclear Information System (INIS)

Alves, J.T.; Lopes, C.M.A.; Assis, J.M.K.; Melo, F.C.L.

2010-01-01

The fabrication of devices for ballistic protection as bullet proof vests and helmets and armored vehicles has been evolving over the past years along with the materials and models used for this specific application. The requirements for high efficient light-weight ballistic protection systems which not interfere in the user comfort and mobility has driven the research in this area. In this work we will present the results of characterization of two ceramics based on alumina and silicon carbide. The ceramics were produced in lab scale and the specific mass, scanning electron microscopy (SEM) microstructure, Vickers hardness, flexural resistance at room temperature and X-ray diffraction were evaluated. Ballistic tests performed in the selected materials showed that the ceramics present armor efficiency. (author)

Effectiveness of eye armor during blast loading.

Science.gov (United States)

Bailoor, Shantanu; Bhardwaj, Rajneesh; Nguyen, Thao D

2015-11-01

Ocular trauma is one of the most common types of combat injuries resulting from the interaction of military personnel with improvised explosive devices. Ocular blast injury mechanisms are complex, and trauma may occur through various injury mechanisms. However, primary blast injuries (PBI) are an important cause of ocular trauma that may go unnoticed and result in significant damage to internal ocular tissues and visual impairment. Further, the effectiveness of commonly employed eye armor, designed for ballistic and laser protection, in lessening the severity of adverse blast overpressures (BOP) is unknown. In this paper, we employed a three-dimensional (3D) fluid-structure interaction computational model for assessing effectiveness of the eye armor during blast loading on human eyes and validated results against free field blast measurements by Bentz and Grimm (2013). Numerical simulations show that the blast waves focused on the ocular region because of reflections from surrounding facial features and resulted in considerable increase in BOP. We evaluated the effectiveness of spectacles and goggles in mitigating the pressure loading using the computational model. Our results corroborate experimental measurements showing that the goggles were more effective than spectacles in mitigating BOP loading on the eye. Numerical results confirmed that the goggles significantly reduced blast wave penetration in the space between the armor and the eyes and provided larger clearance space for blast wave expansion after penetration than the spectacles. The spectacles as well as the goggles were more effective in reducing reflected BOP at higher charge mass because of the larger decrease in dynamic pressures after the impact. The goggles provided greater benefit of reducing the peak pressure than the spectacles for lower charge mass. However, the goggles resulted in moderate, sustained elevated pressure loading on the eye, that became 50-100% larger than the pressure loading

Cost-Effective Manufacturing of Damage-Tolerant Integral Armor

National Research Council Canada - National Science Library

Fink, Bruce

2000-01-01

The U.S. Army Research Laboratory (ARL) and the University of Delaware (UD) have developed an enabling technology to produce a polymer matrix composite-based integral armor with improved multihit ballistic capability...

Thermal-stress analysis and testing of DIII-D armor tiles

International Nuclear Information System (INIS)

Baxi, C.B.; Anderson, P.M.; Reis, E.E.; Smith, J.P.; Smith, P.D.; Croesmann, C.; Watkins, J.; Whitley, J.

1987-10-01

It is planned to install about 1500 new armor tiles in the DIII-D tokamak. The armor tiles currently installed in DIII-D are made by brazing Poco AXF-5Q graphite onto Inconel X-750 stock. A small percentage of these have failed by breakage of graphite. These failures were believed to be related to significant residual stress remaining in graphite after brazing. Hence, an effort was undertaken to improve the design with all-graphite tiles. Three criteria must be satisfied by the armor tiles and the hardware used to attach the tiles to the vessel walls: tiles should not structurally fail, peak tile temperature must be less than 2500 K, and peak vessel stresses must be below acceptable levels. A number of alternate design concepts were first analyzed with the two-dimensional finite element codes TOPAZ2D and NIKE2D. Promising designs were optimized for best parameters such as thicknesses, etc. The two best designs were further analyzed for thermal stresses with the three-dimensional codes P/THERMAL and P/STRESS. Prototype tiles of a number of materials were fabricated by GA and tested at the Plasma Materials Test Facility of the Sandia National Laboratory at Albuquerque. The tests simulated the heat flux and cooling conditions in DIII-D. This paper describes the 2-D and 3-D thermal stress analyses, the test results and logic which led to the selected design of the DIII-D armor tiles. 5 refs., 7 figs., 3 tabs

Statistical description of flume experiments on mixed-size bed-load transport and bed armoring processes

Science.gov (United States)

Chen, D.; Zhang, Y.

2008-12-01

The objective of this paper is to describe the statistical properties of experiments on non-uniform bed-load transport as well as the mechanism of bed armoring processes. Despite substantial effort made over the last two decades, the ability to compute the bed-load flux in a turbulent system remains poor. The major obstacles include the poor understanding of the formation of armor lays on bed surfaces. Such a layer is much flow-resistible than the underlying material and therefore significantly inhibits sediment transport from the reach. To study the problem, we conducted a flume study for mixed sand/gravel sediments. We observed that aggregated sediment blocks were the most common characters in armor layers - the largest sizes resist hydraulic forces, while the smaller sizes add interlocking support and prevent loss of fine material through gaps between the larger particles. Fractional transport rates with the existing of armor layers were measured with time by sediment trapping method at the end of flume. To address the intermittent and time-varying behavior of bed-load transport during bed armoring processes, we investigated the probability distribution of the fractional bed-load transport rates, and the underlying dynamic model derived from the continuous time random walk framework. Results indicate that it is critical to consider the impact of armor layers when a flow is sufficient to move some of the finer particles and yet insufficient to move all the larger particles on a channel bed.

Manufacturing process scale-up of optical grade transparent spinel ceramic at ArmorLine Corporation

Science.gov (United States)

Spilman, Joseph; Voyles, John; Nick, Joseph; Shaffer, Lawrence

2013-06-01

While transparent Spinel ceramic's mechanical and optical characteristics are ideal for many Ultraviolet (UV), visible, Short-Wave Infrared (SWIR), Mid-Wave Infrared (MWIR), and multispectral sensor window applications, commercial adoption of the material has been hampered because the material has historically been available in relatively small sizes (one square foot per window or less), low volumes, unreliable supply, and with unreliable quality. Recent efforts, most notably by Technology Assessment and Transfer (TA and T), have scaled-up manufacturing processes and demonstrated the capability to produce larger windows on the order of two square feet, but with limited output not suitable for production type programs. ArmorLine Corporation licensed the hot-pressed Spinel manufacturing know-how of TA and T in 2009 with the goal of building the world's first dedicated full-scale Spinel production facility, enabling the supply of a reliable and sufficient volume of large Transparent Armor and Optical Grade Spinel plates. With over $20 million of private investment by J.F. Lehman and Company, ArmorLine has installed and commissioned the largest vacuum hot press in the world, the largest high-temperature/high-pressure hot isostatic press in the world, and supporting manufacturing processes within 75,000 square feet of manufacturing space. ArmorLine's equipment is capable of producing window blanks as large as 50" x 30" and the facility is capable of producing substantial volumes of material with its Lean configuration and 24/7 operation. Initial production capability was achieved in 2012. ArmorLine will discuss the challenges that were encountered during scale-up of the manufacturing processes, ArmorLine Optical Grade Spinel optical performance, and provide an overview of the facility and its capabilities.

Structural impact of armor monoblock dimensions on the failure behavior of ITER-type divertor target components: Size matters

Energy Technology Data Exchange (ETDEWEB)

Li, Muyuan; You, Jeong-Ha, E-mail: you@ipp.mpg.de

2016-12-15

Highlights: • Quantitative assessment of size effects was conducted numerically for W monoblock. • Decreasing the width of W monoblock leads to a lower risk of failure. • The Cu interlayer was not affected significantly by varying armor thickness. • The predicted trends were in line with the experimental observations. - Abstract: Plenty of high-heat-flux tests conducted on tungsten monoblock type divertor target mock-ups showed that the threshold heat flux density for cracking and fracture of tungsten armor seems to be related to the dimension of the monoblocks. Thus, quantitative assessment of such size effects is of practical importance for divertor target design. In this paper, a computational study about the thermal and structural impact of monoblock size on the plastic fatigue and fracture behavior of an ITER-type tungsten divertor target is reported. As dimensional parameters, the width and thickness of monoblock, the thickness of sacrificial armor, and the inner diameter of cooling tube were varied. Plastic fatigue lifetime was estimated for the loading surface of tungsten armor and the copper interlayer by use of a cyclic-plastic constitutive model. The driving force of brittle crack growth through the tungsten armor was assessed in terms of J-integral at the crack tip. Decrease of the monoblock width effectively reduced accumulation of plastic strain at the armor surface and the driving force of brittle cracking. Decrease of sacrificial armor thickness led to decrease of plastic deformation at the loading surface due to lower surface temperature, but the thermal and mechanical response of the copper interlayer was not affected by the variation of armor thickness. Monoblock with a smaller tube diameter but with the same armor thickness and shoulder thickness experienced lower fatigue load. The predicted trends were in line with the experimental observations.

Analysis of Terminal Metallic Armor Plate Free-Surface Bulging

National Research Council Canada - National Science Library

Rapacki, Jr, E. J

2008-01-01

.... Terminal ballistic performance evaluations of penetrators and armors are often performed via statistical analyses to obtain a velocity or obliquity at which the expected probability of perforation...

Soft Body Armor: An Overview of Materials, Manufacturing, Testing, and Ballistic Impact Dynamics

Science.gov (United States)

2011-08-01

Atlantic Treaty Organization NIJ National Institute of Justice OTV Outer tactical vest PBI Polybenzimidazole PBO Polybenzobisoxazole PET ...grenades and mortar rounds, is performed in accordance with the North Atlantic Treaty Organization (NATO) Standardization Agreement (STANAG) 2920.6...LEVELS IN SOFT BODY ARMOR The design of woven fabrics for armor applications is complex because it requires an understanding of the related

Development and Verification of Body Armor Target Geometry Created Using Computed Tomography Scans

Science.gov (United States)

2017-07-13

Computed Tomography Scans by Autumn R Kulaga, Kathryn L Loftis, and Eric Murray Approved for public release; distribution is...Army Research Laboratory Development and Verification of Body Armor Target Geometry Created Using Computed Tomography Scans by Autumn R Kulaga...Development and Verification of Body Armor Target Geometry Created Using Computed Tomography Scans 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c

Ballistic Resistance of Armored Passenger Vehicles: Test Protocols and Quality Methods

Energy Technology Data Exchange (ETDEWEB)

Jeffrey M. Lacy; Robert E. Polk

2005-07-01

This guide establishes a test methodology for determining the overall ballistic resistance of the passenger compartment of assembled nontactical armored passenger vehicles (APVs). Because ballistic testing of every piece of every component of an armored vehicle is impractical, if not impossible, this guide describes a testing scheme based on statistical sampling of exposed component surface areas. Results from the test of the sampled points are combined to form a test score that reflects the probability of ballistic penetration into the passenger compartment of the vehicle.

106-17 Telemetry Standards. Annex A.4. Asynchronous Recorder Multiplexer Output Re-Constructor (ARMOR)

Science.gov (United States)

2017-07-01

Output Re-Constructor 1. General This standard defines the recommended multiplexer format for single-channel data recording on small-format (1/2 in...which is 1-based, is determined by the position of the channel’s module in the ARMOR system . The first input channel found in the ARMOR system is

Fabrication, testing and modeling of a new flexible armor inspired from natural fish scales and osteoderms

International Nuclear Information System (INIS)

Chintapalli, Ravi Kiran; Mirkhalaf, Mohammad; Dastjerdi, Ahmad Khayer; Barthelat, Francois

2014-01-01

Crocodiles, armadillo, turtles, fish and many other animal species have evolved flexible armored skins in the form of hard scales or osteoderms, which can be described as hard plates of finite size embedded in softer tissues. The individual hard segments provide protection from predators, while the relative motion of these segments provides the flexibility required for efficient locomotion. In this work, we duplicated these broad concepts in a bio-inspired segmented armor. Hexagonal segments of well-defined size and shape were carved within a thin glass plate using laser engraving. The engraved plate was then placed on a soft substrate which simulated soft tissues, and then punctured with a sharp needle mounted on a miniature loading stage. The resistance of our segmented armor was significantly higher when smaller hexagons were used, and our bio-inspired segmented glass displayed an increase in puncture resistance of up to 70% compared to a continuous plate of glass of the same thickness. Detailed structural analyses aided by finite elements revealed that this extraordinary improvement is due to the reduced span of individual segments, which decreases flexural stresses and delays fracture. This effect can however only be achieved if the plates are at least 1000 stiffer than the underlying substrate, which is the case for natural armor systems. Our bio-inspired system also displayed many of the attributes of natural armors: flexible, robust with ‘multi-hit’ capabilities. This new segmented glass therefore suggests interesting bio-inspired strategies and mechanisms which could be systematically exploited in high-performance flexible armors. This study also provides new insights and a better understanding of the mechanics of natural armors such as scales and osteoderms. (paper)

Mechanisms of stability of armored bubbles: FY 1996 Final Report

International Nuclear Information System (INIS)

Rossen, W.R.; Kam, S.I.

1996-11-01

Theoretical and experimental studies examine how a coating, or open-quotes armor,close quotes of partially wetted solid particles can stabilize tiny bubbles against diffusion of gas into the surrounding liquid, in spite of the high capillary pressures normally associated with such bubbles. Experiments with polymethylmethacrylate (PNMA) beads and carbonated water demonstrate that armored bubbles can persist for weeks in liquid unsaturated with respect to the gas in the bubbles. This question is of concern regarding gas discharges from waste tanks at the Hanford reservation. The stresses on the solid-solid contacts between particles in such cases is large and could drive sintering of the particles into a rigid framework. Stability analysis suggests that a slightly shrunken bubble would not expel a solid particle from its armor to relieve stress and allow the bubble to shrink further. Expulsion of particles from more stressed bubbles at zero capillary pressure is energetically favored in some cases. It is not clear, however, whether this expulsion would proceed spontaneously from a small perturbation or require a large initial disturbance of the bubble. In some cases, it appears that a bubble would expel some particles and shrink, but the bubble would approach a final, stable size rather than disappear completely. This simplified analysis leaves out several factors. For instance, only one perturbation toward expelling a solid from the armor is considered; perhaps other perturbations would be more energetically favored than that tested. Other considerations (particle deformation, surface roughness, contact-angle hysteresis, and adhesion or physical bonding between adjacent particles) would make expelling solids more difficult than indicated by this theoretical study

Micro-engineered first wall tungsten armor for high average power laser fusion energy systems

Science.gov (United States)

Sharafat, Shahram; Ghoniem, Nasr M.; Anderson, Michael; Williams, Brian; Blanchard, Jake; Snead, Lance; HAPL Team

2005-12-01

The high average power laser program is developing an inertial fusion energy demonstration power reactor with a solid first wall chamber. The first wall (FW) will be subject to high energy density radiation and high doses of high energy helium implantation. Tungsten has been identified as the candidate material for a FW armor. The fundamental concern is long term thermo-mechanical survivability of the armor against the effects of high temperature pulsed operation and exfoliation due to the retention of implanted helium. Even if a solid tungsten armor coating would survive the high temperature cyclic operation with minimal failure, the high helium implantation and retention would result in unacceptable material loss rates. Micro-engineered materials, such as castellated structures, plasma sprayed nano-porous coatings and refractory foams are suggested as a first wall armor material to address these fundamental concerns. A micro-engineered FW armor would have to be designed with specific geometric features that tolerate high cyclic heating loads and recycle most of the implanted helium without any significant failure. Micro-engineered materials are briefly reviewed. In particular, plasma-sprayed nano-porous tungsten and tungsten foams are assessed for their potential to accommodate inertial fusion specific loads. Tests show that nano-porous plasma spray coatings can be manufactured with high permeability to helium gas, while retaining relatively high thermal conductivities. Tungsten foams where shown to be able to overcome thermo-mechanical loads by cell rotation and deformation. Helium implantation tests have shown, that pulsed implantation and heating releases significant levels of implanted helium. Helium implantation and release from tungsten was modeled using an expanded kinetic rate theory, to include the effects of pulsed implantations and thermal cycles. Although, significant challenges remain micro-engineered materials are shown to constitute potential

Micro-engineered first wall tungsten armor for high average power laser fusion energy systems

International Nuclear Information System (INIS)

Sharafat, Shahram; Ghoniem, Nasr M.; Anderson, Michael; Williams, Brian; Blanchard, Jake; Snead, Lance

2005-01-01

The high average power laser program is developing an inertial fusion energy demonstration power reactor with a solid first wall chamber. The first wall (FW) will be subject to high energy density radiation and high doses of high energy helium implantation. Tungsten has been identified as the candidate material for a FW armor. The fundamental concern is long term thermo-mechanical survivability of the armor against the effects of high temperature pulsed operation and exfoliation due to the retention of implanted helium. Even if a solid tungsten armor coating would survive the high temperature cyclic operation with minimal failure, the high helium implantation and retention would result in unacceptable material loss rates. Micro-engineered materials, such as castellated structures, plasma sprayed nano-porous coatings and refractory foams are suggested as a first wall armor material to address these fundamental concerns. A micro-engineered FW armor would have to be designed with specific geometric features that tolerate high cyclic heating loads and recycle most of the implanted helium without any significant failure. Micro-engineered materials are briefly reviewed. In particular, plasma-sprayed nano-porous tungsten and tungsten foams are assessed for their potential to accommodate inertial fusion specific loads. Tests show that nano-porous plasma spray coatings can be manufactured with high permeability to helium gas, while retaining relatively high thermal conductivities. Tungsten foams where shown to be able to overcome thermo-mechanical loads by cell rotation and deformation. Helium implantation tests have shown, that pulsed implantation and heating releases significant levels of implanted helium. Helium implantation and release from tungsten was modeled using an expanded kinetic rate theory, to include the effects of pulsed implantations and thermal cycles. Although, significant challenges remain micro-engineered materials are shown to constitute potential

Calculation of Equivalent Resistance for Ground Wires Twined with Armor Rods in Contact Terminals

Directory of Open Access Journals (Sweden)

Gang Liu

2018-03-01

Full Text Available Ground wire breakage accidents can destroy the stable operation of overhead lines. The excessive temperature increase arising from the contact resistance between the ground wire and armor rod in the contact terminal is one of the main reasons causing the breakage of ground wires. Therefore, it is necessary to calculate the equivalent resistance for ground wires twined with armor rods in contact terminals. According to the actual distribution characteristics of the contact points in the contact terminal, a three-dimensional electromagnetic field simulation model of the contact terminal was established. Based on the model, the current distribution in the contact terminal was obtained. Subsequently, the equivalent resistance of a ground wire twined with the armor rod in the contact terminal was calculated. The effects of the factors influencing the equivalent resistance were also discussed. The corresponding verification experiments were conducted on a real ground wire on a contact terminal. The measurement results of the equivalent resistance for the armor rod segment showed good agreement with the electromagnetic modeling results.

Damage Assessment in TiB2 Ceramic Armor Targets

National Research Council Canada - National Science Library

Rupert, Nevin

2001-01-01

The interaction between long rods and ceramics is only partially understood; however, this understanding is essential in the design of improved performance of impact-resistant materials and armor system design applications...

Mock-up development of new warship protective armor structure and feasibility analysis of ship installation

Directory of Open Access Journals (Sweden)

ZHENG Pan

2017-05-01

Full Text Available To ensure the installation of the new design of protective armor structure on larger warships,a study into the installation process of the structure of this armor is carried out to improve installation efficiency and ensure the protective effect. This paper proposes a typical composite armor structure design which is composed of ‘silicate aerogel/ballistic ceramic/high-strength polyethylene/silicate aerogel’. The study analyzes the modeling design,down-selection of materials and equipment,and real ship mock-up technical development. The reliability and application of high strength polyethylene in response to high temperatures in the real ship installation process is discussed. The results show that high-temperatures during welding have no negative impact on the high strength polyethylene of the armored structure. The design demonstrates that this installation process is feasible and can be provided as an alternative solution by virtues of its good maneuverability,controllable precision,checkable quality and high reliability.

Experimental studies on tungsten-armor impact on nuclear responses of solid breeding blanket

International Nuclear Information System (INIS)

Sato, S.; Nakao, M.; Verzilov, Y.; Ochiai, K.; Wada, M.; Kubota, N.; Kondo, K.; Yamauchi, M.; Enoeda, M.; Nishitani, T.

2005-01-01

In order to experimentally evaluate the tungsten armor impact on tritium production of the solid breeding blanket being developed by JAERI for tokamak-type DEMO reactors, neutronics integral experiments have been performed by using DT neutrons at Fusion Neutron Source (FNS) facility of JAERI. Solid breeding blanket mockups relevant to the DEMO blanket have been applied in this study. The mockups are constructed by a set of layers consisting of 0 - 25.2 mm thick tungsten, 16 mm thick F82H, 12 mm thick Li 2 TiO 3 and 100 - 200mm thick beryllium with cross-section of 660 x 660 mm in maximum. Pellets of Li 2 CO 3 are embedded inside the Li 2 TiO 3 layers to measure the tritium production rate. By installing the 5, 12.6 and 25.2 mm thick tungsten armors, sum of the integrated tritium productions at the pellets are reduced by about 2, 3 and 6 % relative to the case without the armor, respectively. Numerical calculations have been conducted using the Monte Carlo code. Calculation results for sum of the integrated tritium productions in the case with the tungsten armor agree well with the experiment data within 4% and 19% under condition without and with a neutron reflector, respectively. (author)

The Future Role of Armor in Central-Eastern Europe

National Research Council Canada - National Science Library

Lorincz, Gabor

2003-01-01

... attrition based military cultures. It seems since the end of the Cold War the armor community has had identity problems caused by the events and the triggered military solutions of the last ten years...

Instant decoys for armored vehicles. A literature survey

NARCIS (Netherlands)

Webb, R.; Leenders, J.

2000-01-01

The TNO Prins Maurits Laboratory is involved with projects that deal with vulnerability of armored vehicles. Such activities take place in both national and international programs and are especially performed in the group Weapon Effectiveness. One of the other groups within TNOPML is the group

Composite treatment of ceramic tile armor

Science.gov (United States)

Hansen, James G. R. [Oak Ridge, TN; Frame, Barbara J [Oak Ridge, TN

2010-12-14

An improved ceramic tile armor has a core of boron nitride and a polymer matrix composite (PMC) facing of carbon fibers fused directly to the impact face of the tile. A polyethylene fiber composite backing and spall cover are preferred. The carbon fiber layers are cured directly onto the tile, not adhered using a separate adhesive so that they are integral with the tile, not a separate layer.

Mock-up test results of monoblock-type CFC divertor armor for JT-60SA

Energy Technology Data Exchange (ETDEWEB)

Higashijima, S. [Japan Atomic Energy Agency, 801-1 Mukoyama, Naka, Ibaraki 311-0193 (Japan)], E-mail: higashijima.satoru@jaea.go.jp; Sakurai, S.; Suzuki, S.; Yokoyama, K.; Kashiwa, Y.; Masaki, K.; Shibama, Y.K.; Takechi, M.; Shibanuma, K.; Sakasai, A.; Matsukawa, M.; Kikuchi, M. [Japan Atomic Energy Agency, 801-1 Mukoyama, Naka, Ibaraki 311-0193 (Japan)

2009-06-15

The JT-60 Super Advanced (JT-60SA) tokamak project starts under both the Japanese domestic program and the international program 'Broader Approach'. The maximum heat flux to JT-60SA divertor is estimated to {approx}15 MW/m{sup 2} for 100 s. Japan Atomic Energy Agency (JAEA) has developed a divertor armor facing high heat flux in the engineering R and D for ITER, and it is concluded that monoblock-type CFC divertor armor is promising for JT-60SA. The JT-60SA armor consists of CFC monoblocks, a cooling CuCrZr screw-tube, and a thin oxygen-free high conductivity copper (OFHC-Cu) buffer layer between the CFC monoblock and the screw-tube. CFC/OFHC-Cu and OFHC-Cu/CuCrZr joints are essential for the armor, and these interfaces are brazed. Needed improvements from ITER engineering R and D are good CFC/OFHC-Cu and OFHC-Cu/CuCrZr interfaces and suppression of CFC cracking. For these purposes, metalization inside CFC monoblock is applied, and we confirmed again that the mock-up has heat removal capability in excess of ITER requirement. For optimization of the fabrication method and understanding of the production yield, the mock-ups corresponding to quantity produced in one furnace at the same time is also produced, and the half of the mock-ups could remove 15 MW/m{sup 2} as required. This paper summarizes the recent progress of design and mock-up test results for JT-60SA divertor armor.

Friction Stir Weld Failure Mechanisms in Aluminum-Armor Structures Under Ballistic Impact Loading Conditions

Science.gov (United States)

2013-01-01

REPORT Friction Stir Weld Failure Mechanisms in Aluminum-Armor Structures Under Ballistic Impact Loading Conditions 14. ABSTRACT 16. SECURITY...properties and of the attendant ballistic-impact failure mechanisms in prototypical friction stir welding (FSW) joints found in armor structures made of high...mechanisms, friction stir welding M. Grujicic, B. Pandurangan, A. Arakere, C-F. Yen, B. A. Cheeseman Clemson University Office of Sponsored Programs 300

75 FR 25208 - Announcement of Body Armor Research Needs Meeting

Science.gov (United States)

2010-05-07

... manufacturing community (including fiber producers, fabric producers, and armor manufacturers) and government..., passport issuing country, passport number, city of birth, country of birth, date of birth, gender, title...

Co-Injection Resin Transfer Molding for Optimization of Integral Armor

National Research Council Canada - National Science Library

Fink, B

1998-01-01

... enhancement over existing defense industry practices. CIRTM was invented and developed for single-step manufacturing of integral armor by enabling simultaneous injection of multiple resins into multi-layer preform...

What Were the Causes of the Delay of the 79th Division Capturing Montfaucon during the Meuse-Argonne Offensive in World War I?

Science.gov (United States)

2011-06-10

7Leonard P. Ayres, The War with Germany: A Statistical Summary (Washington, DC: Government Printing Office, 1919), 21. 8Historical board of the...by looking at this statistic alone, the effectiveness of the primary weapon system of the 79th Division was somewhere around 33 percent. Outside of...those gigantic tanks we had heard so much about.‖178 Fortunately for the men of the 79th, their lack of training in combined arms operations with armor

Highly deformable bones: unusual deformation mechanisms of seahorse armor.

Science.gov (United States)

Porter, Michael M; Novitskaya, Ekaterina; Castro-Ceseña, Ana Bertha; Meyers, Marc A; McKittrick, Joanna

2013-06-01

Multifunctional materials and devices found in nature serve as inspiration for advanced synthetic materials, structures and robotics. Here, we elucidate the architecture and unusual deformation mechanisms of seahorse tails that provide prehension as well as protection against predators. The seahorse tail is composed of subdermal bony plates arranged in articulating ring-like segments that overlap for controlled ventral bending and twisting. The bony plates are highly deformable materials designed to slide past one another and buckle when compressed. This complex plate and segment motion, along with the unique hardness distribution and structural hierarchy of each plate, provide seahorses with joint flexibility while shielding them against impact and crushing. Mimicking seahorse armor may lead to novel bio-inspired technologies, such as flexible armor, fracture-resistant structures or prehensile robotics. Copyright © 2013 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Designing an Innovative Composite Armor System for Affordable Ballistic Protection

National Research Council Canada - National Science Library

Ma, Zheng-Dong; Wang, Hui; Cui, Yushun; Rose, Douglas; Socks, Adria; Ostberg, Donald

2006-01-01

.... This paper focuses on the frontal armor plate and back plate design problems with demonstration examples, including both results of the virtual prototyping and ballistic testing for proof-of-concept...

Virtual Experiments to Determine Behind-Armor Debris for Survivability Analysis

National Research Council Canada - National Science Library

Prakash, Anand

2004-01-01

.... This data is currently generated by conducting laboratory experiments in a standard set-up in which each threat projectile is fired on the actual armor and the BAD pattern is captured on witness plates...

Testing method for ceramic armor and bare ceramic tiles

NARCIS (Netherlands)

Carton, E.P.; Roebroeks, G.H.J.J.

2014-01-01

TNO has developed an alternative, more configuration independent ceramic test method than the standard Depth-of-Penetration test method. In this test ceramic tiles and ceramic based armor are evaluated as target without a semi-infinite backing layer. An energy approach is chosen to evaluate and rank

Ceramic/polymer functionally graded material (FGM) lightweight armor system

Energy Technology Data Exchange (ETDEWEB)

Petrovic, J.J.; McClellan, K.J.

1998-12-31

This is the final report of a two-year, Laboratory Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL). Functionally graded material is an enabling technology for lightweight body armor improvements. The objective was to demonstrate the ability to produce functionally graded ceramic-polymer and ceramic-metal lightweight armor materials. This objective involved two aspects. The first and key aspect was the development of graded-porosity boron-carbide ceramic microstructures. The second aspect was the development of techniques for liquid infiltration of lightweight metals and polymers into the graded-porosity ceramic. The authors were successful in synthesizing boron-carbide ceramic microstructures with graded porosity. These graded-porosity boron-carbide hot-pressed pieces were then successfully liquid-infiltrated in vacuum with molten aluminum at 1,300 C, and with liquid polymers at room temperature. Thus, they were able to demonstrate the feasibility of producing boron carbide-aluminum and boron carbide-polymer functionally graded materials.

Dynamic lift on an artificial static armor layer during highly unsteady open channel flow

OpenAIRE

Spiller, Stephan Mark; Ruther, Nils; Friedrich, Heide

2015-01-01

The dynamic lift acting on a 100 mm × 100 mm section of a static armor layer during unsteady flow is directly measured in a series of physical experiments. The static armor layer is represented by an artificial streambed mold, made from an actual gravel bed. Data from a total of 190 experiments are presented, undertaken in identical conditions. Results show that during rapid discharge increases, the dynamic lift on the streambed repeatedly exhibits three clear peaks. The magnitude of the obse...

Application of nondestructive ion beam analysis to measure variations in the elemental composition of armor materials

Energy Technology Data Exchange (ETDEWEB)

Pallone, Arthur. E-mail: art.pallone@murraystate.edu; Demaree, John; Adams, Jane. E-mail: jadams@arl.army.mil

2004-06-01

Lightweight, state-of-the-art armors rely on ceramics for their enhanced performance. One goal of the United States Army is to expand the industrial base of companies that provide the armors. A systematic study of armor performance as a function of ceramic stoichiometry will result in a better understanding of the fundamental relations between composition and mechanical performance. One ceramic of interest is aluminum oxynitride (AlON). The stoichiometries of representative samples of AlON were investigated with the nondestructive techniques of Rutherford backscattering spectrometry and resonant nuclear reaction analysis. Future tests of the performance of the AlON samples are to be correlated with the stoichiometries, and hence will lead to optimum, standardized processes for the manufacture of the AlON.

Front-facing fluoropolymer-coated armor composite

OpenAIRE

Gamache, Raymond M.; Roland, Charles M.; Fragiadakis, Daniel M.

2018-01-01

Patent A front-facing armor system utilizing a composite laminate backed by a high hardness substrate. The composite laminate comprises a series of first and second layers. The first layer of the bi-layer laminate system is a polymer with a density of at least 1.8 g/ᵌ and having both an amorphous and crystalline phase, and having phase transformation pressure of at least 0.5 GPa at a temperature of 20° C. The second layer of each bi-layer provides acoustic impedance ...

Hydroxyapatite-armored poly(ε-caprolactone) microspheres and hydroxyapatite microcapsules fabricated via a Pickering emulsion route.

Science.gov (United States)

Fujii, Syuji; Okada, Masahiro; Nishimura, Taiki; Maeda, Hayata; Sugimoto, Tatsuya; Hamasaki, Hiroyuki; Furuzono, Tsutomu; Nakamura, Yoshinobu

2012-05-15

Hydroxyapatite (HAp) nanoparticle-armored poly(ε-caprolactone) (PCL) microspheres were fabricated via a "Pickering-type" emulsion solvent evaporation method in the absence of any molecular surfactants. It was clarified that the interaction between carbonyl/carboxylic acid groups of PCL and the HAp nanoparticles at an oil-water interface played a crucial role in the preparation of the stable Pickering-type emulsions and the HAp nanoparticle-armored microspheres. The HAp nanoparticle-armored PCL microspheres were characterized in terms of size, size distribution, morphology, and chemical compositions using scanning electron microscopy, laser diffraction, energy dispersive X-ray microanalysis, and thermogravimetric analysis. The presence of HAp nanoparticles at the surface of the microspheres was confirmed by scanning electron microscopy and energy dispersive X-ray microanalysis. Pyrolysis of the PCL cores led to the formation of the corresponding HAp hollow microcapsules. Copyright © 2012 Elsevier Inc. All rights reserved.

Weldability and Impact Energy Properties of High-Hardness Armor Steel

Science.gov (United States)

Cabrilo, Aleksandar; Geric, Katarina; Jovanovic, Milos; Vukic, Lazic

2018-03-01

In this study, the weldability of high-hardness armor steel by the gas metal arc welding method has been investigated. The study was aimed at determining the weakness points of manual welding compared to automated welding through microhardness testing, the cooling rate, tensile characteristics and nondestructive analysis. Detailed studies were performed for automated welding on the impact energy and microhardness in the fusion line, as the most sensitive zone of the armor steel weld joint. It was demonstrated that the selection of the preheating and interpass temperature is important in terms of the cooling rate and quantity of diffusible and retained hydrogen in the weld joint. The tensile strength was higher than 800 MPa. The width of the heat-affected zone did not exceed 15.9 mm, measured from the weld centerline, while the impact energy results were 74 and 39 J at 20 and - 40 °C, respectively.

Armor of cermet with metal therein increasing with depth

Science.gov (United States)

Wilkins, M.L.; Holt, A.C.; Cline, C.F.; Foreschner, K.E.

1973-07-01

The system described consists of a ceramic matrix having a gradient of fine ductile metallic particles dispersed therein in an amount of from 0.0%, commencing at the front or impact surface of the armor, to about 2 to 15% by volume along the interface to the back of the system. (auth)

Function-Oriented Material Design of Joints for Advance Armors Under Ballistic Impact

National Research Council Canada - National Science Library

Ma, Zheng-Dong; Wang, Hui; Raju, Basavaraju

2004-01-01

The objective of this research is to develop a system of software tools based on a new design methodology for the efficient composite armor structural design under ballistic impact loading conditions...

Sensitization of Naturally Aged Aluminum 5083 Armor Plate

Science.gov (United States)

2015-07-29

5 - 1 - SENSITIZATION OF NATURALLY AGED ALUMINUM 5083 ARMOR PLATE INTRODUCTION Aluminum -magnesium alloys are important for both ship...boundaries [3,4]. The magnesium-rich phase (normally β-Al3Mg2) is highly anodic with respect to the surrounding aluminum phase, thus is susceptible... alloys , and with varying amounts of debris scattered about the surface consistent with corrosion product, Figure 2b, that often forms over time within

Effects of Body Armor Fit on Marksmanship Performance

Science.gov (United States)

2016-09-01

SIMULATORS SIZES(DIMENSIONS) IOTV(IMPROVED OUTER TACTICAL VEST ) U.S. Army Natick Soldier Research, Development and Engineering Center...configurations were counterbalanced to control for order effect. Body Armor. The U.S. Army, standard issue Improved Outer Tactical Vest (IOTV) Generation III...targets at that great of an arc (≥50°) was not operationally realistic. Fig. 2 Improved outer tactical vest (IOTV) Gen III Table 1 Distribution of

Miniaturized hand held microwave interference scanning system for NDE of dielectric armor and armor systems

International Nuclear Information System (INIS)

Schmidt, Karl F.; Little, Jack R.; Ellingson, William A.; Meitzler, Thomas J.; Green, William

2011-01-01

Inspection of ceramic-based armor has advanced through development of a microwave-based, portable, non-contact NDE system. Recently, this system was miniaturized and made wireless for maximum utility in field applications. The electronic components and functionality of the laboratory system are retained, with alternative means of position input for creation of scan images. Validation of the detection capability was recently demonstrated using specially fabricated surrogates and ballistic impact-damaged specimens. The microwave data results have been compared to data from laboratory-based microwave interferometry systems and digital x-ray imaging. The microwave interference scanning has been shown to reliably detect cracks, laminar features and material property variations. The authors present details of the system operation, descriptions of the test samples used and recent results obtained.

A parametric design of ceramic faced composite armor subject to air weapon threats

International Nuclear Information System (INIS)

Guo, Y N; Sun, Q

2015-01-01

By taking into consideration the two categories of military projectile threats to aircraft structures, an optimal layer configuration of ceramic faced composite armor was designed in this paper. Using numerical simulations and the same layer arrangement of ceramic, UHMWPE, and carbon fiber laminates, a parametric finite element model using LS-DYNA code was built. Several thickness combinations were analyzed in order to determine the final lightest configuration that is capable of supporting a high-speed impact load and HEI blast wave load, which implements a high anti-penetration design for aircraft armor. This configuration can be used to improve the anti-impact ability of aircraft structures as well as achieve a structure/function integration design that considers a lighter weight. (paper)

PELE侵彻复合装甲数值模拟%Numerical Simulation of PELE Penetrating Composite Armor

Institute of Scientific and Technical Information of China (English)

李干; 王志军; 王妍; 李硕

2016-01-01

为了探究横向增强型侵彻体(PELE)侵彻复合装甲后的毁伤效果,采用显式非线性动力分析软件AUTODYN,对装填特氟龙(聚四氟乙烯)的侵彻膨胀弹以900 m/s着靶速度侵彻复合靶板的过程进行了数值模拟,得到PELE弹对复合靶侵彻破坏效应及相关参数.结果表明:聚碳酸酯(玻璃纤维)、聚氨酯(泡沫塑料)与凯夫拉复合装甲的结构均被PELE的横向效应所破坏;复合装甲的夹心材料不同,靶板的破坏程度也不尽相同;复合装甲能对PELE的横向效应起到一定的抑制作用,而凯夫拉材料抑制作用较好.%In order to analyze the damage effect of the penetrator with enhanced lateral efficiency( PELE) penetrating composite armor, an explicit nonlinear dynamic analysis software AUTODYN was used to simulate the process of PELE filled with Teflon( polytetrafluoroethylene) penetrating composite target plate using the speed of 900 m/s, and the destructive effect and relevant parameters of PELE penetrating composite armor were obtained finally. The result shows that the composite armor constructed by polycarbonate( glass fibre) ,polyurethane and Kevlar is damaged seriously by lateral efficiency of PELE. The different composite-armors have different damage. The composite armor has definite inhibitory effect on lateral efficiency of PELE,and the inhibitory effect of Kevlar is better.

Second International Research Conference on the History of Arms and Armor in Kyiv, Ukraine

Directory of Open Access Journals (Sweden)

Denys Toichkin

2016-12-01

Full Text Available The present report provides a short description of a conference titled “Second International Research Conference on the History of Arms and Armor in Kyiv, Ukraine”. It was the second scientific conference dedicated to the study of historical weapons in Ukraine. A number of international experts in the field of historical arms and armor were invited to the conference. Each researcher had been asked to provide a short and a long article on a specific research subject. The short articles had already been published in a peer-review booklet that was handed out before the start of the conference. The long articles will be published together as a large collection of paper in future.

Flow and Turbulence at Rubble-Mound Breakwater Armor Layers under Solitary Wave

DEFF Research Database (Denmark)

Jensen, Bjarne; Christensen, Erik Damgaard; Sumer, B. Mutlu

2015-01-01

This paper presents the results of an experimental investigation of the flow and turbulence at the armor layer of rubble-mound breakwaters during wave action. The study focused on the details of the flow and turbulence in the armor layer and on the effect of the porous core on flow and stability....... To isolate the processes involved with the flow in the porous core, experiments were conducted with increasing complexity. Specifically, three parallel experiments were performed including (1) an impermeable smooth breakwater slope, (2) an impermeable breakwater slope with large roughness elements added...... to the breakwater, and (3) a porous breakwater where the porous core was added below the breakwater front. One breakwater slope of 1:1.5 was applied. In this paper the focus is on the details of a single sequence of wave approach, run-up, and rundown. To isolate this sequence the experiments were performed applying...

Transformation: Transition From a Heavy to a Lighter Family of Armored Fighting Vehicles

National Research Council Canada - National Science Library

Petty, Thomas

2001-01-01

Since the end of World War II, the single event with greatest impact on the development of armor was the war that did not happen-the expected conflict between the United States and the Soviet Union...

27 CFR 478.37 - Manufacture, importation and sale of armor piercing ammunition.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2010-04-01 2010-04-01 false Manufacture, importation... COMMERCE IN FIREARMS AND AMMUNITION Administrative and Miscellaneous Provisions § 478.37 Manufacture, importation and sale of armor piercing ammunition. No person shall manufacture or import, and no manufacturer...

The genetic architecture of parallel armor plate reduction in threespine sticklebacks.

Directory of Open Access Journals (Sweden)

Pamela F Colosimo

2004-05-01

Full Text Available How many genetic changes control the evolution of new traits in natural populations? Are the same genetic changes seen in cases of parallel evolution? Despite long-standing interest in these questions, they have been difficult to address, particularly in vertebrates. We have analyzed the genetic basis of natural variation in three different aspects of the skeletal armor of threespine sticklebacks (Gasterosteus aculeatus: the pattern, number, and size of the bony lateral plates. A few chromosomal regions can account for variation in all three aspects of the lateral plates, with one major locus contributing to most of the variation in lateral plate pattern and number. Genetic mapping and allelic complementation experiments show that the same major locus is responsible for the parallel evolution of armor plate reduction in two widely separated populations. These results suggest that a small number of genetic changes can produce major skeletal alterations in natural populations and that the same major locus is used repeatedly when similar traits evolve in different locations.

Armor systems including coated core materials

Science.gov (United States)

Chu, Henry S [Idaho Falls, ID; Lillo, Thomas M [Idaho Falls, ID; McHugh, Kevin M [Idaho Falls, ID

2012-07-31

An armor system and method involves providing a core material and a stream of atomized coating material that comprises a liquid fraction and a solid fraction. An initial layer is deposited on the core material by positioning the core material in the stream of atomized coating material wherein the solid fraction of the stream of atomized coating material is less than the liquid fraction of the stream of atomized coating material on a weight basis. An outer layer is then deposited on the initial layer by positioning the core material in the stream of atomized coating material wherein the solid fraction of the stream of atomized coating material is greater than the liquid fraction of the stream of atomized coating material on a weight basis.

Standard Methodology for Assessment of Range of Motion While Wearing Body Armor

Science.gov (United States)

2013-09-30

76 STANDING STATURE (with Footwear ...Thanks also to Natick Soldier Research, Development and Engineering Center and the Soldier Integrated Protection Team and those project officers who...being fit into their best body armor size for that configuration): • Standing Stature (with footwear ) • Seated Stature At the goniometer station

Development of conductively cooled first wall armor and actively cooled divertor structure for ITER/FER

International Nuclear Information System (INIS)

Ioki, K.; Yamada, M.; Sakata, S.; Okada, K.; Toyoda, M.; Shimizu, K.; Tsujimura, S.; Iimura, M.; Akiba, M.; Araki, M.; Seki, M.

1991-01-01

Based on the design requirements for the plasma facing components in ITER/FER, we have performed design studies on the conductively cooled first wall armor and the divertor plate with sliding supports. The full-scale armor tiles were fabricated for heat load tests, and good thermal performances were obtained in heat load tests of 0.2-0.4 MW/m 2 . It is shown by the thermomechanical analysis on the divertor plate that thermal stresses and bending deformation are reduced significantly by using the sliding supports. The divertor test module with the sliding supports has been fabricated to investigate its fabricability and to verify the functions of the sliding supports during a high heat load of about 10 MW/m 2 . (orig.)

Modeling the Biodynamical Response of the Human Thorax with Body Armor from a Bullet Impact

National Research Council Canada - National Science Library

Lobuono, John

2001-01-01

.... The finite element model of the human thorax is validated by comparing the model's results to experimental data obtained from cadavers wearing a protective body armor system undergoing a projectile impact...

Modeling the Biodynamical Response of the Human Thorax With Body Armor From a Bullet Impact

National Research Council Canada - National Science Library

Lobuono, John

2001-01-01

.... The finite element model of the human thorax is validated by comparing the model's results to experimental data obtained from cadavers wearing a protective body armor system undergoing a projectile impact...

Laser-induced micro-jetting from armored droplets

KAUST Repository

Marston, J. O.

2015-06-23

We present findings from an experimental study of laser-induced cavitation within a liquid drop coated with a granular material, commonly referred to as “armored droplets” or “liquid marbles.” The cavitation event follows the formation of plasma after a nanosecond laser pulse. Using ultra-high-speed imaging up to 320,610 fps, we investigate the extremely rapid dynamics following the cavitation, which manifests itself in the form of a plethora of micro-jets emanating simultaneously from the spaces between particles on the surface of the drop. These fine jets break up into droplets with a relatively narrow diameter range, on the order of 10 μm. © 2015, Springer-Verlag Berlin Heidelberg.

Modeling the Biodynamical Response of the Human Thorax with Body Armor from a Bullet Impact

National Research Council Canada - National Science Library

Lobuono, John

2001-01-01

The objective of this study is to develop a finite element model of the human thorax with a protective body armor system so that the model can adequately determine the thorax's biodynamical response...

Modeling the Biodynamical Response of the Human Thorax With Body Armor From a Bullet Impact

National Research Council Canada - National Science Library

Lobuono, John

2001-01-01

The objective of this study is to develop a finite element model of the human thorax with a protective body armor system so that the model can adequately determine the thorax's biodynamical response...

Characteristics of behind armor blunt trauma produced by bullets with different structural materials: an experimental study

Directory of Open Access Journals (Sweden)

Ling-qing WANG

2013-07-01

Full Text Available Objective　To investigate the effect of structural materials of bullets on behind armor blunt trauma (BABT. Methods　Ten healthy male Landraces were randomly divided into two groups (5 each: 56 type 7.62-mm rifle bullet group and SS109 5.56-mm rifle bullet group. The kinetic energy of two types of bullets was adjusted to the same level (about 1880J by the way of grow downwards gunpowder. Then the animals as protected with both grade NIJ Ⅲ ceramic hard armor and grade Ⅱ police soft body armor, were shot at the left midclavicular line of fourth intercostal space (shooting distance was 25m. The damage to the animals was observed. Other 2 healthy male Landraces were selected, and biomechanical sensor was subcutaneously implanted into the soft tissue in precordium and intracalvarium to detect the pressure at the time point of bullet contact under the protection of armor, and the relationship between pressure and damage was analyzed. Results　Respiration, heart rate and systolic arterial pressure of animals in two groups were all elevated after injury, but there was no significant difference between the two groups. No obvious change was found on blood oxygen saturation of both groups. Gross anatomy showed the predominant local injury was cardiac and pulmonary contusions. The area of pulmonary hemorrhage of 7.62mm group was 6.00%±3.18%, significantly higher than that of 5.56mm group (3.59%±2.11%, P<0.05. Histopathological examination revealed acute injuries of lung tissues, myocardial tissue and cerebral cortical neurons. The contents of cardiac troponin T (TnT, creatine kinase (CK and creatine kinase-MB (CK-MB isoenzyme were all increased 3 hours after injury, and the rise was higher in 7.62mm group than in 5.56mm group (P<0.05. Biomechanical testing showed the pressure of precordium and intracalvarium was elevated at the moment of bullet contact, and the rise was higher in 7.62mm group than in 5.56mm group (P<0.05. Conclusions�

Physics and Technology of Transparent Ceramic Armor: Sintered Al2O3 vs Cubic Materials

National Research Council Canada - National Science Library

Krell, Andreas; Hutzler, Thomas; Klimke, Jens

2006-01-01

Sintered sub-micrometer alumina (alpha-Al2O3) is the hardest transparent armor. However, its trigonal structure gives rise to a strong thickness effect that makes thicker components translucent. Cubic ceramics (no birefringence...

Improving the Success of Light Armored Vehicle Drivers: A Qualitative Descriptive Narrative Study

Science.gov (United States)

Byrd, Dathan

2016-01-01

This qualitative descriptive narrative research was the first known study to collect participants' perceptions on the effectiveness of the Marine Corps' Light Armored Vehicle driver training. The general problem was the Marine Corps' vague guidance on curriculum development, instruction, and assessment for driver training of the Light armored…

Production and characterization of ceramics for armor application; Producao e caracterizacao de ceramicas para blindagem balistica

Energy Technology Data Exchange (ETDEWEB)

Alves, J.T.; Lopes, C.M.A. [Instituto Tecnologico de Aeronautica (ITA), Sao Jose dos Campos, SP (Brazil). Div. de Engenharia Mecanica-Aeronautica; Assis, J.M.K.; Melo, F.C.L., E-mail: cmoniz@iae.cta.b [Instituto de Aeronautica e Espaco (IAE), Sao Jose dos Campos, SP (Brazil). Div. de Materiais

2010-07-01

The fabrication of devices for ballistic protection as bullet proof vests and helmets and armored vehicles has been evolving over the past years along with the materials and models used for this specific application. The requirements for high efficient light-weight ballistic protection systems which not interfere in the user comfort and mobility has driven the research in this area. In this work we will present the results of characterization of two ceramics based on alumina and silicon carbide. The ceramics were produced in lab scale and the specific mass, scanning electron microscopy (SEM) microstructure, Vickers hardness, flexural resistance at room temperature and X-ray diffraction were evaluated. Ballistic tests performed in the selected materials showed that the ceramics present armor efficiency. (author)

Extending the Operational Relevance of the Current Heavy Mechanized and Armor Force to 2020 and Beyond

National Research Council Canada - National Science Library

Boston, Gerald

2003-01-01

Can the U.S. Army's current heavy mechanized and armor force adapt emerging Joint Vision 2020 operational concepts, in order to remain relevant to the land power requirements of combatant commanders across...

Enhancement in ballistic performance of composite hard armor through carbon nanotubes

Directory of Open Access Journals (Sweden)

Jason Gibson

2013-12-01

Full Text Available The use of carbon nanotubes in composite hard armor is discussed in this study. The processing techniques to make various armor composite panels consisting of Kevlar®29 woven fabric in an epoxy matrix and the subsequent V50 test results for both 44 caliber soft-point rounds and 30 caliber FSP (fragment simulated projectile threats are presented. A 6.5% improvement in the V50 test results was found for a combination of 1.65 wt% loading of carbon nanotubes and 1.65 wt% loading of milled fibers. The failure mechanism of carbon nanotubes during the ballistic event is discussed through scanning electron microscope images of the panels after the failure. Raman Spectroscopy was also utilized to evaluate the residual strain in the Kevlar®29 fibers post shoot. The Raman Spectroscopy shows a Raman shift of 25 cm−1 for the Kevlar®29 fiber utilized in the composite panel that had an enhancement in the V50 performance by using milled fiber and multi-walled carbon nanotubes. Evaluating both scenarios where an improvement was made and other panels without any improvement allows for understanding of how loading levels and synergistic effects between carbon nanotubes and milled fibers can further enhance ballistic performance.

Vacuum UV spectroscopy of armor erosion from plasma gun disruption simulation experiments

International Nuclear Information System (INIS)

Rockett, P.D.; Gahl, J.M.; Zhitlukhin, A.; Arkhipov, K.; Bakhtin, V.; Toporkov, D.; Ovchinnokov, I.; Kuznetsov, V.E.; Titov, V.A.

1995-01-01

Extensive simulations of tokamak disruptions have provided a picture of material erosion that is limited by the transfer of energy from the incident plasma to the armor solid surface through a dense vapor shield. Two transmission grating vacuum ultraviolet (VUV) spectrographs were designed and utilized to study the plasma-material interface in plasma gun simulation experiments. Target materials included POCO graphite, ATJ graphite, boron nitride and plasma-sprayed tungsten. Detailed spectra were recorded with a spatial resolution of ca. 0.7mm resolution on VIKA at Efremov and on 2MK-200 at Troitsk. Time-resolved data with 40-200ns resolution were then recorded along with the same spatial resolution on 2MK-200. The VIKA plasma gun directly illuminated a target with a high-intensity plasma pulse of 2-100MJm -2 with low-energy ions of ca. 100eV. The 2MK-200 plasma gun illuminated the target via a magnetic cusp that permitted only deuterium to pass with energies of ca. 1keV, but which produced a fairly low intensity of 2MJm -2 . Power densities on target ranged from 10 7 to 10 8 Wcm -2 . Emitted spectra were recorded from 15 to 450A over a distance from 0 to 7cm above the armor target surface. The data from both plasma gun facilities demonstrated that the hottest plasma region was sitting several millimeters above the armor tile surface. This apparently constituted the absorption region, which confirmed past computer simulations. Spectra indicated both the species and ionization level that were being ablated from the target, demonstrating impurity content, and showing plasma ablation velocity. Graphite samples clearly showed CV lines as well as impurity lines from O V and O VI. The BN tiles produced textbook examples of BIV and BV, and extensive NIV, V and VI lines. These are being compared with radiation-hydrodynamic calculations. (orig.)

High energy ballistic and fracture comparison between multilayered armor systems using non-woven curaua fabric composites and aramid laminates

Directory of Open Access Journals (Sweden)

Fábio de Oliveira Braga

2017-10-01

Full Text Available For personal protection against high kinetic energy projectiles, multilayered armor systems (MAS are usually the best option. They combine synergistically the properties of different materials such as ceramics, composites and metals. In the present work, ballistic tests were performed to evaluate multilayered armor systems (MAS using curaua non-woven fabric epoxy composites as second layer. A comparison to a MAS using aramid (Kevlar™ fabric laminates was made. The results showed that the curaua non-woven fabric composites are suitable to the high ballistic applications, and are promising substitutes for aramid fabric laminates. Keywords: Composite, Natural fiber, Curaua fiber, Non-woven fabric, Aramid laminate, Ballistic test

The Armys Armored Multi Purpose Vehicle (AMPV): Background and Issues for Congress

Science.gov (United States)

2016-02-24

1 Information in this section is taken from Christopher F. Foss, Jane’s Armour and Artillery, 2011-2012...for the ABCT AMPV is 2,907 vehicles—a 10 vehicle increase over 2013 quantities. Discussions with the AMPV Program Manager revealed the 10 extra...Selected Weapon Programs, GAO-14-340SP, March 2014, p. 129. 14 CRS Meeting with AMPV Program Manager May 20, 2014. 15 Ibid. The Army’s Armored Multi

Development, installation, and initial operation of DIII-D graphite armor tiles

International Nuclear Information System (INIS)

Anderson, P.M.; Baxi, C.B.; Reis, E.E.; Smith, J.P.; Smith, P.D.

1988-04-01

An upgrade of the DIII-D vacuum vessel protection system has been completed. The ceiling, floor, and inner wall have been armored to enable operation of CIT-relevant doublenull diverted plasmas and to enable the use of the inner wall as a limiting surface. The all- graphite tiles replace the earlier partial coverage armor configuration which consisted of a combination of Inconel tiles and graphite brazed to Inconel tiles. A new all-graphite design concept was chosen for cost and reliability reasons. The 10 minute duration between plasma discharges required the tiles to be cooled by conduction to the water-cooled vessel wall. Using two and three- dimensional analyses, the tile design was optimized to minimize thermal stresses with uniform thermal loading on the plasma-facing surface. Minimizing the stresses around the tile hold-down feature and eliminating stress concentrators were emphasized in the design. The design of the tile fastener system resulted in sufficient hold-down forces for good thermal conductance to the vessel and for securing the tile against eddy current forces. The tiles are made of graphite, and a program to select a suitable grade of graphite was undertaken. Initially, graphites were compared based on published technical data. Graphite samples were then tested for thermal shock capacity in an electron beam test facility at the Sandia National Laboratory (SNLA) in Albuquerque, New Mexico, USA. 4 refs., 6 figs

Physiological, Biomechanical, and Maximal Performance Comparisons of Female Soldiers Carrying Loads Using Prototype U.S. Marine Corps Modular Lightweight Load-Carrying Equipment (MOLLE) with Interceptor Body Armor and U.S. Army All-Purpose Lightweight Individual Carrying Equipment (ALICE) with PASGT Body Armor

National Research Council Canada - National Science Library

Harman, Everett

1999-01-01

The experiment evaluated the physiological, biomechanical, and maximal performance responses of 12 female soldiers carrying loads with prototype Modular Lightweight Load-Carrying Equipment with Interceptor body armor (MOLLE...

Fugitive emissions control on dry copper tailing with crushed rock armor

International Nuclear Information System (INIS)

Haase, E.F.

1992-01-01

Four inactive copper tailing impoundments totalling 1,900 acres near Ajo in southwestern Arizona were covered on horizontal surfaces with a 2 in. nominal thickness of crushed rock to control particulate emissions. The tailings are typically dominated by sand-sized particles but may also include significant PM 10 fractions towards the centers of the impoundments. The technology was selected by Phelps Dodge Corporation, after investigation of several alternatives, as a permanent and practical cover that essentially eliminates fugitive emissions. It simulates the natural desert pavement that characterizes this arid area of the Sonoran Desert. Rocky overburden was crushed to minus 3 in. diameter and broadcast on dry surfaces of tailing impoundments with all-terrain, balloon-tired spreaders. Stony residues in the rock armor tend to cement together following rainfall, forming a crust that enhances surface stability and erosion control. Slopes with windblown tailing deposition were covered to a nominal 6 in. thickness by conventional dozer pushing and blading of minus 10 in. rock over the sides. Athel trees, planted extensively since 1970 on two of the four inactive impoundments, provided partial control of fugitives, but were subjected to harsh environmental conditions, including abrasion from saltating particles. The rock armor functions as a mulch which is expected to improve water relations for existing vegetation and areas seeded with native species. New surface microenvironments, and the virtual elimination of surface creep and saltation, are expected to support native plant growth under favorable climatic conditions

Nondestructive ultrasonic characterization of armor grade silicon carbide

Science.gov (United States)

Portune, Andrew Richard

Ceramic materials have traditionally been chosen for armor applications for their superior mechanical properties and low densities. At high strain rates seen during ballistic events, the behavior of these materials relies upon the total volumetric flaw concentration more so than any single anomalous flaw. In this context flaws can be defined as any microstructural feature which detriments the performance of the material, potentially including secondary phases, pores, or unreacted sintering additives. Predicting the performance of armor grade ceramic materials depends on knowledge of the absolute and relative concentration and size distribution of bulk heterogeneities. Ultrasound was chosen as a nondestructive technique for characterizing the microstructure of dense silicon carbide ceramics. Acoustic waves interact elastically with grains and inclusions in large sample volumes, and were well suited to determine concentration and size distribution variations for solid inclusions. Methodology was developed for rapid acquisition and analysis of attenuation coefficient spectra. Measurements were conducted at individual points and over large sample areas using a novel technique entitled scanning acoustic spectroscopy. Loss spectra were split into absorption and scattering dominant frequency regimes to simplify analysis. The primary absorption mechanism in polycrystalline silicon carbide was identified as thermoelastic in nature. Correlations between microstructural conditions and parameters within the absorption equation were established through study of commercial and custom engineered SiC materials. Nonlinear least squares regression analysis was used to estimate the size distributions of boron carbide and carbon inclusions within commercial SiC materials. This technique was shown to additionally be capable of approximating grain size distributions in engineered SiC materials which did not contain solid inclusions. Comparisons to results from electron microscopy

Army Training Study: Training Effectiveness Analysis (TEA) Summary. Volume 1. Armor.

Science.gov (United States)

1978-08-08

c. r tf(e rx =r) rfs it ,, 0’( r’( r , a S’ f "’ u nn Ir Irf I I. * 222 ARM’- NN :TuDY TWANINC EFFCIUENEZ-: ANALISIS TEA : MMARY ’JLUM~ I ARMOR U...selected 5 ’.e o. 11 module clusters , read the objectives fr.r te firs. im’dule, studied whatever available Yesource mnatterial he wished, and reported...ambitious an undertaking, since the percentage of trainees who completed SrTh1 averaged 66% over all task clusters . A completion rate of 52% was reported

Nondestructive characterization of UHMWPE armor materials

Science.gov (United States)

Chiou, Chien-Ping; Margetan, Frank J.; Barnard, Daniel J.; Hsu, David K.; Jensen, Terrence; Eisenmann, David

2012-05-01

Ultra-high molecular weight polyethylene (UHMWPE) is a material increasingly used for fabricating helmet and body armor. In this work, plate specimens consolidated from thin fiber sheets in series 3124 and 3130 were examined with ultrasound, X-ray and terahertz radiation. Ultrasonic through-transmission scans using both air-coupled and immersion modes revealed that the 3130 series material generally had much lower attenuation than the 3124 series, and that certain 3124 plates had extremely high attenuation. Due to the relatively low inspection frequencies used, pulse-echo immersion ultrasonic testing could not detect distinct flaw echoes from the interior. To characterize the nature of the defective condition that was responsible for the high ultrasonic attenuation, terahertz radiation in the time-domain spectroscopy mode were used to image the flaws. Terahertz scan images obtained on the high attenuation samples clearly showed a distribution of a large number of defects, possibly small planar delaminations, throughout the volume of the interior. Their precise nature and morphology are to be verified by optical microscopy of the sectioned surface.

Nondestructive characterization of UHMWPE armor materials

International Nuclear Information System (INIS)

Chiou, Chien-Ping; Margetan, Frank J.; Barnard, Daniel J.; Hsu, David K.; Jensen, Terrence; Eisenmann, David

2012-01-01

Ultra-high molecular weight polyethylene (UHMWPE) is a material increasingly used for fabricating helmet and body armor. In this work, plate specimens consolidated from thin fiber sheets in series 3124 and 3130 were examined with ultrasound, X-ray and terahertz radiation. Ultrasonic through-transmission scans using both air-coupled and immersion modes revealed that the 3130 series material generally had much lower attenuation than the 3124 series, and that certain 3124 plates had extremely high attenuation. Due to the relatively low inspection frequencies used, pulse-echo immersion ultrasonic testing could not detect distinct flaw echoes from the interior. To characterize the nature of the defective condition that was responsible for the high ultrasonic attenuation, terahertz radiation in the time-domain spectroscopy mode were used to image the flaws. Terahertz scan images obtained on the high attenuation samples clearly showed a distribution of a large number of defects, possibly small planar delaminations, throughout the volume of the interior. Their precise nature and morphology are to be verified by optical microscopy of the sectioned surface.

Fragmentation of armor piercing steel projectiles upon oblique perforation of steel plates

Directory of Open Access Journals (Sweden)

Aizik F.

2012-08-01

Full Text Available In this study, a constitutive strength and failure model for a steel core of a14.5 mm API projectile was developed. Dynamic response of a projectile steel core was described by the Johnson-Cook constitutive model combined with principal tensile stress spall model. In order to obtain the parameters required for numerical description of projectile core material behavior, a series of planar impact experiments was done. The parameters of the Johnson-Cook constitutive model were extracted by matching simulated and experimental velocity profiles of planar impact. A series of oblique ballistic experiments with x-ray monitoring was carried out to study the effect of obliquity angle and armor steel plate thickness on shattering behavior of the 14.5 mm API projectile. According to analysis of x-ray images the fragmentation level increases with both steel plate thickness and angle of inclination. The numerical modeling of the ballistic experiments was done using commercial finite element code, LS-DYNA. Dynamic response of high hardness (HH armor steel was described using a modified Johnson-Cook strength and failure model. A series of simulations with various values of maximal principal tensile stress was run in order to capture the overall fracture behavior of the projectile’s core. Reasonable agreement between simulated and x-ray failure pattern of projectile core has been observed.

Bone histology sheds light on the nature of the "dermal armor" of the enigmatic sauropod dinosaur Agustinia ligabuei Bonaparte, 1999

Science.gov (United States)

Bellardini, Flavio; Cerda, Ignacio A.

2017-02-01

Agustinia ligabuei is an Early Cretaceous sauropod dinosaur from the northwest of Patagonia that is currently the topic of debate with respect to its phylogenetic position and atypical dermal armor. The presence of four morphotypes of laminar and transversely elongated putative osteoderms was used to consider Agustinia as an armored sauropod. Regarding the different hypotheses about the identity of the bony structures of Agustinia (e.g., osteoderms, cervical or dorsal ribs, hypertrophied elements), a comparative histological analysis has been carried out. Histological evidence is presented herein and reveals that none of the morphotypes of Agustinia shows a primary bone tissue formed by structural fiber bundles as in other sauropod dinosaur osteoderms. Furthermore, on the basis of their gross morphology and microstructure, the bony structures originally classified as types 1 + 4 and 3 are more comparable respectively with dorsal and cervical ribs than any other kind of dermal or bony element. Due to poor preservation, the nature of the type 2 cannot be assessed but is here tentatively assigned to a pelvic girdle element. Although a phylogenetic reassessment of Agustinia is not the purpose of this paper, our paleohistological analyses have broader implications: by not supporting the dermal armor hypothesis for Agustinia, its inclusion in Lithostrotia is not justified in the absence of other diagnostic features.

Armor: An αβγ assembly for irradiated fuel analysis

International Nuclear Information System (INIS)

Beraud, M.

1967-04-01

The assembly ARMOR which was built with a view to carrying out research on irradiated fuels consists of an αβγ enclosure made up of 11 cells in line. After a general description of the assembly in its present form, the various functions are reviewed: introduction of the samples, chemical de-canning, dissolution of the irradiated uranium pellets, preparation of solutions for mass spectrometric analyses, disposal of the effluents and of the solid waste. The assembly-has been working since 1961. During the 5 to 6 years operation, various improvements have been made and a certain number of observations have been collected concerning the work. (author) [fr

Coated armor system and process for making the same

Science.gov (United States)

Chu, Henry S.; Lillo, Thomas M.; McHugh, Kevin M.

2010-11-23

An armor system and method involves providing a core material and a stream of atomized coating material that comprises a liquid fraction and a solid fraction. An initial layer is deposited on the core material by positioning the core material in the stream of atomized coating material wherein the solid fraction of the stream of atomized coating material is less than the liquid fraction of the stream of atomized coating material on a weight basis. An outer layer is then deposited on the initial layer by positioning the core material in the stream of atomized coating material wherein the solid fraction of the stream of atomized coating material is greater than the liquid fraction of the stream of atomized coating material on a weight basis.

Design of Vibration Absorber using Spring and Rubber for Armored Vehicle 5.56 mm Caliber Rifle

Directory of Open Access Journals (Sweden)

Aditya Sukma Nugraha

2014-12-01

Full Text Available This paper presents a design of vibration absorber using spring and rubber for 5.56 mm caliber rifle armored vehicle. Such a rifle is used in a Remote-Controlled Weapon System (RCWS or a turret where it is fixed using a two degree of freedom pan-tilt mechanism. A half car lumped mass dynamic model of armored vehicles was derived. Numerical simulation was conducted using fourth order Runge Kutta method. Various types of vibration absorbers using spring and rubber with different configurations are installed in the elevation element. Vibration effects on horizontal direction, vertical direction and angular deviation of the elevation element was investigated. Three modes of fire were applied i.e. single fire, semi-automatic fire and automatic fire. From simulation results, it was concluded that the parallel configuration of damping rubber type 3, which has stiffness of 980,356.04 (N/m2 and damping coefficient of 107.37 (N.s/m, and Carbon steel spring whose stiffness coefficient is 5.547 x 106 (N/m2 provides the best vibration absorption. 

The natural armors of fish: A comparison of the lamination pattern and structure of scales.

Science.gov (United States)

Murcia, Sandra; Lavoie, Ellen; Linley, Tim; Devaraj, Arun; Ossa, E Alex; Arola, D

2017-09-01

Fish scales exhibit a unique balance of flexibility, strength and toughness, which is essential to provide protection without encumbering locomotion. Although the mechanical behavior and structure of this natural armor are of recent interest, a comparison of these qualities from scales of different fish species has not been reported. In this investigation the armor of fish with different locomotion, size and protection needs were analyzed. Scales from the Arapaima gigas, the tarpon (Megalops atlanticus) and the carp (Cyprinus carpio) were compared in terms of the stacking sequence of individual plies and their microstructure. The scales were also compared with respect to anatomical position to distinguish site-specific functional differences. Results show that the lamination sequence of plies for the carp and tarpon exhibit a Bouligand structure with relative rotation of 75° between consecutive plies. The arapaima scales exhibit a cross-ply structure, with 90° rotation between adjacent plies. In addition, results indicate that the volume fraction of reinforcement, the number of plies and the variations in thickness with anatomical position are unique amongst the three fish. These characteristics should be considered in evaluations focused on the mechanical behavior. Copyright © 2016 Elsevier Ltd. All rights reserved.

The natural armors of fish: A comparison of the lamination pattern and structure of scales

Energy Technology Data Exchange (ETDEWEB)

Murcia, Sandra; Lavoie, Ellen; Linley, Tim; Devaraj, Arun; Ossa, E. Alex; Arola, D.

2017-09-01

Fish scales exhibit a unique balance of flexibility, strength and toughness, which is essential to provide protection without encumbering locomotion. Although the mechanical behavior and structure of this natural armor are of recent interest, a comparison of these qualities from scales of different fish species has not been reported. In this investigation the armor of fish with different locomotion, size and protection needs were analyzed. Scales from the Arapaima gigas, the tarpon (Megalops atlanticus) and the carp (Cyprinus carpio) were compared in terms of the stacking sequence of individual plies and their microstructure. The scales were also compared with respect to anatomical position to distinguish site-specific functional differences. Results show that the lamination sequence of plies for the carp and tarpon exhibit a Bouligand structure with relative rotation of 75° between consecutive plies. The arapaima scales exhibit a cross-ply structure, with 90° rotation between adjacent plies. In addition, results indicate that the volume fraction of reinforcement, the number of plies and the variations in thickness with anatomical position are unique amongst the three fish. These characteristics should be considered in evaluations focused on the mechanical behavior.

A Preliminary Report on the Strength and Metallography of a Bimetallic Friction Stir Weld Joint Between AA6061 and MIL-DTL-46100E High Hardness Steel Armor

Science.gov (United States)

2012-11-26

bimetallic friction stir weld joint between AA6061 and MIL-DTL-46100E High Hardness steel armor. ABSTRACT One half inch thick plates of 6061-T6 aluminum...alloy and High Hardness steel armor (MIL- STD-46100) were successfully joined by the friction stir welding (FSW) process using a tungsten-rhenium...4. TITLE AND SUBTITLE A preliminary report on the strength and metallography of a bimetallic friction stir weld joint between AA6061 and MIL-DTL

Ballistic Performance of Mallow and Jute Natural Fabrics Reinforced Epoxy Composites in Multilayered Armor

OpenAIRE

Nascimento, Lucio Fabio Cassiano; Louro, Luis Henrique Leme; Monteiro, Sergio Neves; Gomes, Alaelson Vieira; Marçal, Rubens Lincoln Santana Blazutti; Lima Júnior, Édio Pereira; Margem, Jean Igor

2017-01-01

Natural fiber reinforced polymer composites have recently been investigated as a component of multilayered armor system (MAS). These composites were found to present advantages when replacing conventional high strength synthetic aramid fabric laminate composite (KevlarTM, with same thickness, as MAS second layer. Continuous and loose natural fibers were up to now mostly used to reinforce these ballistic composites. Only two natural fabrics reinforced polymer composite were so far used with sa...

Activities of HIP joining of plasma-facing armors in the blanket first-wall in Korea

Energy Technology Data Exchange (ETDEWEB)

Jung, Yang-Il, E-mail: yijung@kaeri.re.kr [Korea Atomic Energy Research Institute, Daedeok-daero, Daejeon 34057 (Korea, Republic of); Park, Jeong-Yong; Choi, Byoung-Kwon; Lee, Jung-Suk; Kim, Hyun-Gil; Park, Dong-Jun; Park, Jung-Hwan; Kim, Suk-Kwon; Lee, Dong-Won [Korea Atomic Energy Research Institute, Daedeok-daero, Daejeon 34057 (Korea, Republic of); Cho, Seungyon [National Fusion Research Institute, Gwahak-ro, Yuseong, Daejeon 34133 (Korea, Republic of)

2016-11-01

Highlights: • HIP joints of Be/CuCrZr, Be/FMS, W/FMS were demonstrated. • The process conditions for HIP joining were developed. • For the joining of Be, coating interlayers as well as thick diffusion barrier was developed. • For the joining of W, double-staged HIP was applied for the joint integrity. • No significant defects nor a brittle failure were observed along the joint interface. - Abstract: Joining technology for dissimilar materials was developed for the fabrication of an ITER blanket first-wall, which consisted of Be, CuCrZr, and stainless steel (SS). The Be/CuCrZr/SS joint was fabricated using a hot isostatic pressing (HIP) method. Beryllium armor was joined to the CuCrZr/SS block at 580 °C under 100 MPa. The optimal interlayer coatings of Cr/Cu and Ti/Cr/Cu were developed using an ion-beam assisted physical vapor deposition. Beryllium is also a candidate armor material for the TBM first-wall. Successful joining of Be to ferritic-martensitic steel (FMS) was accomplished using an HIP method by introducing the thick diffusion barrier. A thick diffusion barrier of a Cu foil(10 μm) limited the excessive diffusion and prevented the formation of brittle phases at the Be/FMS interface. Be and FMS were bonded at 650–850 °C; however, a temperature of lower than 750 °C was recommended to avoid material degradation of FMS. In addition, the joining of W to FMS has been developed. Tungsten is another armor material applicable to more severe plasma conditions. The large difference in the thermal expansion between W and FMS was resolved by introducing the Ti interlayer and Mo separator. Moreover, the double-staged HIP (the first stage at 900 °C and 100 MPa and the second stage at 750 °C and 70 MPa) was applied to suppress the edge delamination of W/FMS joints during thermal history.

Combat Power Analysis is Combat Power Density

Science.gov (United States)

2012-05-17

Lanchester equations, Weapon Effectiveness Index (WEI), Weighted Unit Value (WUV), Armored Division Equivalents (ADE), and Unit Frontages. The research...6 Lanchester Equations... Lanchester Equations ............................................................................................... 53 Appendix C: Relative Combat Power

Assessing a Suitable Contribution of the French Armor Branch to the Doctrinal Development of Violence: Mastering Operations in the Urban Environment

National Research Council Canada - National Science Library

Millet, Jean-Michel

2003-01-01

.... This study analyzes the current state of the French Army doctrinal development of armor employment in the violence-mastering mode in the urban environment and compare it to the lessons learned...

The Army's Light Infantry Divisions: An Analysis of Advocacy and Opposition

National Research Council Canada - National Science Library

Wray, Timothy A

2005-01-01

.... In the ten years since the American withdrawal from Vietnam, the general trend of US Army force structure development had been toward heavy mechanized and armor forces, and so Wickham's decision...

Study of Nano Powder for Improvement the Mechanical Properties of Armor

Directory of Open Access Journals (Sweden)

Raid Salih Jawad

2016-03-01

Full Text Available During this research nano alumina particles are used as reinforce material to improve characterization of armor. The work involves use of polyester resin as matrix. The properties obtained of resulted samples showed clearly improvement. Where values show linear increases in hardness from low value 77.3 gf/mm of pure polyester to high value 81.6 of polystyrene - 30 wt % nano alumina. Values of thermal conductivity greatly influenced by amount of porosity and so on the density of the sample, where pure polyester has low value 0.0661 W/mk of thermal conductivity and polyester – 30 wt % nano aluminapossess conductivity 0.3411 W/mk.

Investigation of Fire-Vulnerability-Reduction Effectiveness of Fire-Resistant Diesel Fuel in Armored Vehicular Fuel Tanks

Science.gov (United States)

1980-09-30

FORT LEE VA 23801 ATTN DRXMD-MS LEXINGTON KY 40511 HQ, US ARHY ARMOR SCHOOL ATTN ATSB- TD HQ, US ARMY T&E COMMANI) FORT KNOX KY 40121 ATTN DRSTE-TO-O 1...CDM P 0 BOX 4005 FORT BELVOIR VA 22060 CHAMPAIGN IL 61820 CDR IHQ US ARMY INFANTRY SCHOOL , US ARMY TRAINING & DOCTRINE CMD ATTN ATSH-CD-MS-M ATTN ATCD

Development of high conductive C/C composite tiles for plasma facing armor

International Nuclear Information System (INIS)

Ioki, K.; Namiki, K.; Tsujimura, S.; Toyoda, M.; Seki, M.; Takatsu, H.

1991-01-01

C/C composites with high thermal conductivity were developed in unidirectional, two-dimensional and felt types, and were fabricated as full-scale armor tile. Their thermal conductivity in the direction perpendicular to the plasma-side surface is 250∝550 W/mdeg C, that is comparable to that of pyrolytic graphite. It was shown by heat load tests that the C/C composites have low surface erosion characteristics and high thermal shock resistance. Various kinds of C/C composites were successfully bonded to metal substrate, and their mechanical strength and thermal shock resistance were tested. (orig.)

Korea - 1950: The Decision to Invade the North...(What Would Carl Have Thought?)

National Research Council Canada - National Science Library

Moseley, T. M

1989-01-01

Sunday, 0400 hours, 25 June 1950...the assault came without warning. Eight North Korean infantry divisions exploded across the 38th Parallel into South Korea through gaps torn by armor and artillery...

Graphene-Armored Aluminum Foil with Enhanced Anticorrosion Performance as Current Collectors for Lithium-Ion Battery.

Science.gov (United States)

Wang, Mingzhan; Tang, Miao; Chen, Shulin; Ci, Haina; Wang, Kexin; Shi, Liurong; Lin, Li; Ren, Huaying; Shan, Jingyuan; Gao, Peng; Liu, Zhongfan; Peng, Hailin

2017-12-01

Aluminum (Al) foil, as the most accepted cathode current collector for lithium-ion batteries (LIBs), is susceptible to local anodic corrosions during long-term operations. Such corrosions could lead to the deterioration or even premature failure of the batteries and are generally believed to be a bottleneck for next-generation 5 V LIBs. Here, it is demonstrated that Al foil armored by conformal graphene coating exhibits significantly reinforced anodic corrosion resistance in both LiPF 6 and lithium bis(trifluoromethanesulphonyl) imide (LiTFSI) based electrolytes. Moreover, LiMn 2 O 4 cells using graphene-armored Al foil as current collectors (LMO/GA) demonstrate enhanced electrochemical performance in comparison with those using pristine Al foil (LMO/PA). The long-term discharge capacity retention of LMO/GA cell after ≈950 h straight operations at low rate (0.5 C) reaches up to 91%, remarkably superior to LMO/PA cell (75%). The self-discharge propensity of LMO/GA is clearly relieved and the rate/power performance is also improved with graphene mediations. This work not only contributes to the long-term stable operations of LIBs but also might catalyze the deployment of 5 V LIBs in the future. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

تاريخ القانون في المجتمعات القديمة (قانون حمورابي أنموذجاً History of Law in ancient societies (Law of Hammurabi as a model

Directory of Open Access Journals (Sweden)

Mustafa Fadhil Karim al-Khafaji مصطفى فاضل كريم الخفاجي

2013-12-01

Full Text Available Is a subject formed obsession from the first side among first researchers in the affairs of the ancient civilization and this is due to the importance of this issue , which stems from the jealousy of previous civilizations , reflecting the pioneering ancient Iraqi civilization Vngdo studied the evolution of human thought . It is the second given by many researchers are of great importance and overlapping text similarity between the Code of Hammurabi and the law of the Torah , which makes the need to study the law in order to study the monotheistic thought and demonstrate its development. Either the third is derived from the significant impact it has had this law in thought contemplative Greek also appeared in the canons of the Elders of Greece such as ( Solon and the other from here , we can define the importance of this issue in our research that it reflects the evolution of Iraqi civilization and Raadatha and impact which commit us to re- always reading for this exploration of thought and its impact .

NATO Advanced Research Workshop on Boron Rich Solids Sensors for Biological and Chemical Detection, Ultra High Temperature Ceramics, Thermoelectrics, Armor

CERN Document Server

Orlovskaya, Nina

2011-01-01

The objective of this book is to discuss the current status of research and development of boron-rich solids as sensors, ultra-high temperature ceramics, thermoelectrics, and armor. Novel biological and chemical sensors made of stiff and light-weight boron-rich solids are very exciting and efficient for applications in medical diagnoses, environmental surveillance and the detection of pathogen and biological/chemical terrorism agents. Ultra-high temperature ceramic composites exhibit excellent oxidation and corrosion resistance for hypersonic vehicle applications. Boron-rich solids are also promising candidates for high-temperature thermoelectric conversion. Armor is another very important application of boron-rich solids, since most of them exhibit very high hardness, which makes them perfect candidates with high resistance to ballistic impact. The following topical areas are presented: •boron-rich solids: science and technology; •synthesis and sintering strategies of boron rich solids; •microcantileve...

Armor stability of hardly (or partly) reshaping berm breakwaters

DEFF Research Database (Denmark)

Moghim, M. N.; Andersen, Thomas Lykke

2015-01-01

This paper deals with stability of hardly (or partly) reshaping berm breakwaters. A simple physical argument is used to derive a new stability formula based on the assumption that the maximum wave force causing damage of armor layer is proportional to the maximum wave momentum flux near...... the structure toe. The main goal of the present paper is to provide an estimation technique based on this physical principle to predict the deformation of the front slope in terms of the eroded area. The proposed method is verified by comparison with model test data. It is found that by using the maximum wave...... momentum flux approach the damage to the front slope (eroded area) can be very well predicted. Moreover, a simple method to estimate the eroded area based on measured or calculated berm recession (Rec) and depth of intersection of reshaped and initial profile (hf) is presented. The performance...

Computational Fair Division

DEFF Research Database (Denmark)

Branzei, Simina

Fair division is a fundamental problem in economic theory and one of the oldest questions faced through the history of human society. The high level scenario is that of several participants having to divide a collection of resources such that everyone is satisfied with their allocation -- e.g. two...... heirs dividing a car, house, and piece of land inherited. The literature on fair division was developed in the 20th century in mathematics and economics, but computational work on fair division is still sparse. This thesis can be seen as an excursion in computational fair division divided in two parts....... The first part tackles the cake cutting problem, where the cake is a metaphor for a heterogeneous divisible resource such as land, time, mineral deposits, and computer memory. We study the equilibria of classical protocols and design an algorithmic framework for reasoning about their game theoretic...

On infinitely divisible semimartingales

DEFF Research Database (Denmark)

Basse-O'Connor, Andreas; Rosiński, Jan

2015-01-01

to non Gaussian infinitely divisible processes. First we show that the class of infinitely divisible semimartingales is so large that the natural analog of Stricker's theorem fails to hold. Then, as the main result, we prove that an infinitely divisible semimartingale relative to the filtration generated...... by a random measure admits a unique decomposition into an independent increment process and an infinitely divisible process of finite variation. Consequently, the natural analog of Stricker's theorem holds for all strictly representable processes (as defined in this paper). Since Gaussian processes...... are strictly representable due to Hida's multiplicity theorem, the classical Stricker's theorem follows from our result. Another consequence is that the question when an infinitely divisible process is a semimartingale can often be reduced to a path property, when a certain associated infinitely divisible...

Integrating Unmanned Aerial Vehicles (UAVs) With Current Combat Search and Rescue (CSAR) Doctrine

National Research Council Canada - National Science Library

Altieri, Jayson

2003-01-01

0300 hours (Zulu) somewhere north of Baghdad Major Chris Foster, call sign BACH-21, was flying a CAP mission supporting two flights of Air Guard F-16s attacking an Iraqi armor division retreating south towards Baghdad...

Division of Finance Homepage

Science.gov (United States)

Top Department of Administration logo Alaska Department of Administration Division of Finance Search Search the Division of Finance site DOF State of Alaska Finance Home Content Area Accounting Charge Cards You are here Administration / Finance Division of Finance Updates IRIS Expenditure Object Codes

Cell Division Synchronization

Science.gov (United States)

The report summarizes the progress in the design and construction of automatic equipment for synchronizing cell division in culture by periodic...Concurrent experiments in hypothermic synchronization of algal cell division are reported.

Argonne Physics Division Colloquium

Science.gov (United States)

[Argonne Logo] [DOE Logo] Physics Division Home News Division Information Contact PHY Org Chart Physics Division Colloquium Auditorium, Building 203, Argonne National Laboratory Fridays at 11:00 AM 2017 : Sereres Johnston 15 Sep 2017 Joint Physics and Materials Science Colloquium J. C. Séamus Davis, Cornell

Divisible ℤ-modules

Directory of Open Access Journals (Sweden)

Futa Yuichi

2016-03-01

Full Text Available In this article, we formalize the definition of divisible ℤ-module and its properties in the Mizar system [3]. We formally prove that any non-trivial divisible ℤ-modules are not finitely-generated.We introduce a divisible ℤ-module, equivalent to a vector space of a torsion-free ℤ-module with a coefficient ring ℚ. ℤ-modules are important for lattice problems, LLL (Lenstra, Lenstra and Lovász base reduction algorithm [15], cryptographic systems with lattices [16] and coding theory [8].

Biological armors under impact—effect of keratin coating, and synthetic bio-inspired analogues

International Nuclear Information System (INIS)

Achrai, B; Wagner, H D; Bar-On, B

2015-01-01

A number of biological armors, such as turtle shells, consist of a strong exoskeleton covered with a thin keratin coating. The mechanical role upon impact of this keratin coating has surprisingly not been investigated thus far. Low-velocity impact tests on the turtle shell reveal a unique toughening phenomenon attributed to the thin covering keratin layer, the presence of which noticeably improves the fracture energy and shell integrity. Synthetic substrate/coating analogues were subsequently prepared and exhibit an impact behavior similar to the biological ones. The results of the present study may improve our understanding, and even future designs, of impact-tolerant structures. (paper)

The Properties of Arc-Sprayed Aluminum Coatings on Armor-Grade Steel

Directory of Open Access Journals (Sweden)

Marcin Adamiak

2018-02-01

Full Text Available This article presents the results of an examination of the properties of arc-sprayed aluminum on alloyed armor-grade steel. Thermal arc spraying was conducted with a EuTronic Arc Spray 4 wire arc sprayer. Aluminum wire 1.6 mm in diameter was used to produce dense, abrasion- and erosion-resistant coatings approx. 1.0 mm thick with and without nickel/5% aluminum-buffered subcoating. Aluminum coatings were characterized in accordance with ASTM G 65-00 abrasion resistance test, ASTM G 76-95 erosion resistance tests, ASTM C 633-01 adhesion strength, HV0.1 hardness tests and metallographic analyses. Results demonstrate properties of arc-sprayed aluminum and aluminum-nickel material coatings that are especially promising in industrial applications where erosion-, abrasion- and corrosion-resistant coating properties are required.

Experimental Facilities Division/User Program Division technical progress report 1999-2000

International Nuclear Information System (INIS)

2001-01-01

In October 1999, the two divisions of the Advanced Photon Source (APS), the Accelerator Systems Division (ASD) and the Experimental Facilities Division (XFD), were reorganized into four divisions (see high-level APS organizational chart, Fig. 1.1). In addition to ASD and XFD, two new divisions were created, the APS Operations Division (AOD), to oversee APS operations, and the User Program Division (UPD), to serve the APS user community by developing and maintaining the highest quality user technical and administration support. Previous XFD Progress Reports (ANL/APS/TB-30 and ANL/APS/TB-34) covered a much broader base, including APS user administrative support and what was previously XFD operations (front ends, interlocks, etc.) This Progress Report summarizes the main scientific and technical activities of XFD, and the technical support, research and development (R and D) activities of UPD from October 1998 through November 2000. The report is divided into four major sections, (1) Introduction, (2) SRI-CAT Beamlines, Technical Developments, and Scientific Applications, (3) User Technical Support, and (4) Major Plans for the Future. Sections 2 and 3 describe the technical activities and research accomplishments of the XFD and UPD personnel in supporting the synchrotron radiation instrumentation (SRI) collaborative access team (CAT) and the general APS user community. Also included in this report is a comprehensive list of publications (Appendix 1) and presentations (Appendix 2) by XFD and UPD staff during the time period covered by this report. The organization of section 2, SRI CAT Beamlines, Technical Developments, and Scientific Applications has been made along scientific techniques/disciplines and not ''geographical'' boundaries of the sectors in which the work was performed. Therefore items under the subsection X-ray Imaging and Microfocusing could have been (and were) performed on several different beamlines by staff in different divisions. The management of

Division of atomic physics

International Nuclear Information System (INIS)

Kroell, S.

1994-01-01

The Division of Atomic Physics, Lund Institute of Technology (LTH), is responsible for the basic physics teaching in all subjects at LTH and for specialized teaching in Optics, Atomic Physics, Atomic and Molecular Spectroscopy and Laser Physics. The Division has research activities in basic and applied optical spectroscopy, to a large extent based on lasers. It is also part of the Physics Department, Lund University, where it forms one of eight divisions. Since the beginning of 1980 the research activities of our division have been centred around the use of lasers. The activities during the period 1991-1992 is described in this progress reports

Technical activities, 1990: Surface Science Division

International Nuclear Information System (INIS)

Powell, C.J.

1991-05-01

The report summarizes technical activities and accomplishments of the NIST Surface Science Division during Fiscal Year 1990. Overviews are presented of the Division and of its three constituent groups: Surface Dynamical Processes, Thin Films and Interfaces, and Surface Spectroscopies and Standards. These overviews are followed by reports of selected technical accomplishments during the year. A summary is given of Division outputs and interactions that includes lists of publications, talks, committee assignments, seminars (including both Division seminars and Interface Science seminars arranged through the Division), conferences organized, and a standard reference material certified. Finally, lists are given of Division staff and of guest scientists who have worked in the Division during the past year

Development of remote replacement system for armor tiles of first wall of FER

International Nuclear Information System (INIS)

Adachi, Junichi; Yoshizawa, Shunji; Nakano, Yasuo; Kuboyama, Takashi; Shibanuma, Kiyoshi; Kakudate, Satoshi; Oka, Kiyoshi.

1993-01-01

A remote system has been developed to replace automatically armor tiles of first walls with a single manipulator arm for the Fusion Experimental Reactor (FER). The system is composed of a manipulator arm and an end-effector (a tile replacement hand), which have a gripper of the tiles, a nutrunner to rotate attatching bolts of them and a vision sensor to measure positions of them. The system can replace the tiles by means of a visual feedback system using vision sensor, even if the positions of the tiles would have changed. As a result of tests, it has been proved that the end-effector is useful and the control system is practicable. (author)

One Dimension Analytical Model of Normal Ballistic Impact on Ceramic/Metal Gradient Armor

International Nuclear Information System (INIS)

Liu Lisheng; Zhang Qingjie; Zhai Pengcheng; Cao Dongfeng

2008-01-01

An analytical model of normal ballistic impact on the ceramic/metal gradient armor, which is based on modified Alekseevskii-Tate equations, has been developed. The process of gradient armour impacted by the long rod can be divided into four stages in this model. First stage is projectile's mass erosion or flowing phase, mushrooming phase and rigid phase; second one is the formation of comminuted ceramic conoid; third one is the penetration of gradient layer and last one is the penetration of metal back-up plate. The equations of third stage have been advanced by assuming the behavior of gradient layer as rigid-plastic and considering the effect of strain rate on the dynamic yield strength

One Dimension Analytical Model of Normal Ballistic Impact on Ceramic/Metal Gradient Armor

Science.gov (United States)

Liu, Lisheng; Zhang, Qingjie; Zhai, Pengcheng; Cao, Dongfeng

2008-02-01

An analytical model of normal ballistic impact on the ceramic/metal gradient armor, which is based on modified Alekseevskii-Tate equations, has been developed. The process of gradient armour impacted by the long rod can be divided into four stages in this model. First stage is projectile's mass erosion or flowing phase, mushrooming phase and rigid phase; second one is the formation of comminuted ceramic conoid; third one is the penetration of gradient layer and last one is the penetration of metal back-up plate. The equations of third stage have been advanced by assuming the behavior of gradient layer as rigid-plastic and considering the effect of strain rate on the dynamic yield strength.

An Analysis Plan for the ARCOMS II (Armor Combat Operations Model Support II) Experiment.

Science.gov (United States)

1983-06-01

In order to facilitate Armor Combat Modeling, the data analysis shculd focus upon the methods which transform the data intc descriptive or predictive ...discussed in Chapter III tc predict the Farameter for probability of detection in time ŕt. This should be compared with the results of the N.4gh -t Vision...J 6A 46.) I-I 0 f U-CL 0~ z o -Z 06 09 03 v 0 0 SJldnYS 10 ON Ipgr Cp o LSTm n at emn itgas 4AA rI z ;A (AZ - 090.0 UlA0 -O ON 404 Fiur CAd &P CC

E-Division activities report

International Nuclear Information System (INIS)

Barschall, H.H.

1984-07-01

E (Experimental Physics) Division carries out basic and applied research in atomic and nuclear physics, in materials science, and in other areas related to the missions of the Laboratory. Some of the activities are cooperative efforts with other divisions of the Laboratory, and, in a few cases, with other laboratories. Many of the experiments are directly applicable to problems in weapons and energy, some have only potential applied uses, and others are in pure physics. This report presents abstracts of papers published by E (Experimental Physics) Division staff members between July 1983 and June 1984. In addition, it lists the members of the scientific staff of the division, including visitors and students, and some of the assignments of staff members on scientific committees. A brief summary of the budget is included

Progress report of Applied Physics Division. 1 October 1980 - 30 June 1981. Acting Division Chief - Dr. J. Parry

International Nuclear Information System (INIS)

2004-01-01

In September 1980, the Commission approved a reorganization of Physics Division, Engineering Research Division and Instrumentation and Control Division to form two new research divisions to be known as Applied Physics Division and Nuclear Technology Division. The Applied Physics Division will be responsible for applied science programs, particularly those concerned with nuclear techniques. The Division is organized as four sections with the following responsibilities: (1) Nuclear Applications and Energy Studies Section. Program includes studies in nuclear physics, nuclear applications, ion implantation and neutron scattering. (2) Semiconductor and Radiation Physics Section. Studies in semiconductor radiation detectors, radiation standards and laser applications. (3) Electronic Systems Section. This includes systems analysis, digital systems, instrument design, project instrumentation and instrument maintenance. (4) Fusion Physics Section. This covers work carried out by staff currently attached to university groups (author)

Use of Body Armor Protection Levels with Squad Automatic Weapon Fighting Load Impacts Soldier Performance, Mobility, and Postural Control

Science.gov (United States)

2015-05-01

Industrial Security Manual , Section ll-19 or DoD 5200.1-R, Information Security Program Regulation, Chapter IX. For Unclassified/Limited...accomplished using PSAW Statistics 18.0 ( SPSS Inc., Chicago, IL, USA). Separate analyses were performed to test each of the three hypotheses stated. However...the Soldier and diminish his/her lethality or survivability , which may be an area of consideration for future research. 4.2 Consequences of Body Armor

Division Quilts: A Measurement Model

Science.gov (United States)

Pratt, Sarah S.; Lupton, Tina M.; Richardson, Kerri

2015-01-01

As teachers seek activities to assist students in understanding division as more than just the algorithm, they find many examples of division as fair sharing. However, teachers have few activities to engage students in a quotative (measurement) model of division. Efraim Fischbein and his colleagues (1985) defined two types of whole-number…

Comparison of Concussion Rates Between NCAA Division I and Division III Men's and Women's Ice Hockey Players.

Science.gov (United States)

Rosene, John M; Raksnis, Bryan; Silva, Brie; Woefel, Tyler; Visich, Paul S; Dompier, Thomas P; Kerr, Zachary Y

2017-09-01

Examinations related to divisional differences in the incidence of sports-related concussions (SRC) in collegiate ice hockey are limited. To compare the epidemiologic patterns of concussion in National Collegiate Athletic Association (NCAA) ice hockey by sex and division. Descriptive epidemiology study. A convenience sample of men's and women's ice hockey teams in Divisions I and III provided SRC data via the NCAA Injury Surveillance Program during the 2009-2010 to 2014-2015 academic years. Concussion counts, rates, and distributions were examined by factors including injury activity and position. Injury rate ratios (IRRs) and injury proportion ratios (IPRs) with 95% confidence intervals (CIs) were used to compare concussion rates and distributions, respectively. Overall, 415 concussions were reported for men's and women's ice hockey combined. The highest concussion rate was found in Division I men (0.83 per 1000 athlete-exposures [AEs]), followed by Division III women (0.78/1000 AEs), Division I women (0.65/1000 AEs), and Division III men (0.64/1000 AEs). However, the only significant IRR was that the concussion rate was higher in Division I men than Division III men (IRR = 1.29; 95% CI, 1.02-1.65). The proportion of concussions from checking was higher in men than women (28.5% vs 9.4%; IPR = 3.02; 95% CI, 1.63-5.59); however, this proportion was higher in Division I women than Division III women (18.4% vs 1.8%; IPR = 10.47; 95% CI, 1.37-79.75). The proportion of concussions sustained by goalkeepers was higher in women than men (14.2% vs 2.9%; IPR = 4.86; 95% CI, 2.19-10.77), with findings consistent within each division. Concussion rates did not vary by sex but differed by division among men. Checking-related concussions were less common in women than men overall but more common in Division I women than Division III women. Findings highlight the need to better understand the reasons underlying divisional differences within men's and women's ice hockey and the

Armored kinorhynch-like scalidophoran animals from the early Cambrian.

Science.gov (United States)

Zhang, Huaqiao; Xiao, Shuhai; Liu, Yunhuan; Yuan, Xunlai; Wan, Bin; Muscente, A D; Shao, Tiequan; Gong, Hao; Cao, Guohua

2015-11-26

Morphology-based phylogenetic analyses support the monophyly of the Scalidophora (Kinorhyncha, Loricifera, Priapulida) and Nematoida (Nematoda, Nematomorpha), together constituting the monophyletic Cycloneuralia that is the sister group of the Panarthropoda. Kinorhynchs are unique among living cycloneuralians in having a segmented body with repeated cuticular plates, longitudinal muscles, dorsoventral muscles, and ganglia. Molecular clock estimates suggest that kinorhynchs may have diverged in the Ediacaran Period. Remarkably, no kinorhynch fossils have been discovered, in sharp contrast to priapulids and loriciferans that are represented by numerous Cambrian fossils. Here we describe several early Cambrian (~535 million years old) kinorhynch-like fossils, including the new species Eokinorhynchus rarus and two unnamed but related forms. E. rarus has characteristic scalidophoran features, including an introvert with pentaradially arranged hollow scalids. Its trunk bears at least 20 annuli each consisting of numerous small rectangular plates, and is armored with five pairs of large and bilaterally placed sclerites. Its trunk annuli are reminiscent of the epidermis segments of kinorhynchs. A phylogenetic analysis resolves E. rarus as a stem-group kinorhynch. Thus, the fossil record confirms that all three scalidophoran phyla diverged no later than the Cambrian Period.

Tactical Reconnaissance and Security for the Armor Battalion Commander: Is the Scout Platoon Combat Capable or Combat Ineffective?

Science.gov (United States)

1990-12-27

reconnaissance force back to a heavy ele ,._.it capable of security missions and limited 10 reconnaissance. Vletnam continued the platoon’s emphasis on...College, Fort Leavenworth, KS, 30 November 1988 (CARL Ref. AOR215860). JouroaI ~ el Bacevich, LTC A. J. "Training Scouts." Armor, September 1987, pp. 37...Swanson, Major Steven G. " Bronco Nine Speaks His Mind." MIlitaryInteigence, April-June 1990, pp. 8- 10, 12. "The Bustle Rack." Armo,; March-April 1990

77 FR 40586 - Coastal Programs Division

Science.gov (United States)

2012-07-10

... DEPARTMENT OF COMMERCE National Oceanic and Atmospheric Administration Coastal Programs Division AGENCY: Coastal Programs Division, Office of Ocean and Coastal Resource Management, National Ocean.... FOR FURTHER INFORMATION CONTACT: Kerry Kehoe, Coastal Programs Division (NORM/3), Office of Ocean and...

Theoretical Division progress report

International Nuclear Information System (INIS)

Cooper, N.G.

1979-04-01

This report presents highlights of activities in the Theoretical (T) Division from October 1976-January 1979. The report is divided into three parts. Part I presents an overview of the Division: its unique function at the Los Alamos Scientific Laboratory (LASL) and within the scientific community as a whole; the organization of personnel; the main areas of research; and a survey of recent T-Division initiatives. This overview is followed by a survey of the 13 groups within the Division, their main responsibilities, interests, and expertise, consulting activities, and recent scientific accomplisments. The remainder of the report, Parts II and III, is devoted to articles on selected research activities. Recent efforts on topics of immediate interest to energy and weapons programs at LASL and elsewhere are described in Part II, Major National Programs. Separate articles present T-Divison contributions to weapons research, reactor safety and reactor physics research, fusion research, laser isotope separation, and other energy research. Each article is a compilation of independent projects within T Division, all related to but addressing different aspects of the major program. Part III is organized by subject discipline, and describes recent scientific advances of fundamental interest. An introduction, defining the scope and general nature of T-Division efforts within a given discipline, is followed by articles on the research topics selected. The reporting is done by the scientists involved in the research, and an attempt is made to communicate to a general audience. Some data are given incidentally; more technical presentations of the research accomplished may be found among the 47 pages of references. 110 figures, 5 tables

Prokaryotic cell division: flexible and diverse

NARCIS (Netherlands)

den Blaauwen, T.

2013-01-01

Gram-negative rod-shaped bacteria have different approaches to position the cell division initiating Z-ring at the correct moment in their cell division cycle. The subsequent maturation into a functional division machine occurs in vastly different species in two steps with appreciable time in

Fusion energy division computer systems network

International Nuclear Information System (INIS)

Hammons, C.E.

1980-12-01

The Fusion Energy Division of the Oak Ridge National Laboratory (ORNL) operated by Union Carbide Corporation Nuclear Division (UCC-ND) is primarily involved in the investigation of problems related to the use of controlled thermonuclear fusion as an energy source. The Fusion Energy Division supports investigations of experimental fusion devices and related fusion theory. This memo provides a brief overview of the computing environment in the Fusion Energy Division and the computing support provided to the experimental effort and theory research

49 CFR 1242.03 - Made by accounting divisions.

Science.gov (United States)

2010-10-01

... 49 Transportation 9 2010-10-01 2010-10-01 false Made by accounting divisions. 1242.03 Section 1242... accounting divisions. The separation shall be made by accounting divisions, where such divisions are maintained, and the aggregate of the accounting divisions reported for the quarter and for the year. ...

2017 T Division Lightning Talks

Energy Technology Data Exchange (ETDEWEB)

Ramsey, Marilyn Leann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Abeywardhana, Jayalath AMM [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Adams, Colin Mackenzie [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Adams, Luke Clyde [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Carter, Austin Lewis [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Ducru, Pablo Philippe [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Duignan, Thomas John [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Gifford, Brendan Joel [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Hills, Benjamin Hale [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Hoffman, Kentaro Jack [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Khair, Adnan Ibne [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Kochanski, Kelly Anne Pribble [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Ledwith, Patrick John [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Leveillee, Joshua Anthony [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Lewis, Sina Genevieve [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Ma, Xiaoyu [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Merians, Hugh Drake [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Moore, Bryan Alexander [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Nijjar, Parmeet Kaur [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Oles, Vladyslav [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Olszewski, Maciej W. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Philipbar, Brad Montgomery [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Reisner, Andrew Ray [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Roberts, David Benjamin [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Rufa, Dominic Antonio [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Sifain, Andrew E. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Smith, Justin Steven [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Smith, Lauren Taylor Wisbey [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Svolos, Lampros [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Thibault, Joshua Ryan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Ushijima-Mwesigwa, Hayato Montezuma [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Weaver, Claire Marie [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Witzen, Wyatt Andrew [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Zentgraf, Sabine Silvia [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Alred, John Michael [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-10-06

All members of the T Division Community, students, staff members, group leaders, division management, and other interested individuals are invited to come and support the following student(s) as they present their Lightning Talks.

Division: The Sleeping Dragon

Science.gov (United States)

Watson, Anne

2012-01-01

Of the four mathematical operators, division seems to not sit easily for many learners. Division is often described as "the odd one out". Pupils develop coping strategies that enable them to "get away with it". So, problems, misunderstandings, and misconceptions go unresolved perhaps for a lifetime. Why is this? Is it a case of "out of sight out…

E-Division activities report

International Nuclear Information System (INIS)

Barschall, H.H.

1979-07-01

This report describes some of the activities in E (Experimental Physics) Division during the past year. E-Division carries out research and development in areas related to the missions of the Laboratory. Many of the activities are in pure and applied atomic and nuclear physics. In addition, this report describes work on accelerators, radiation damage, microwaves, and plasma diagnostics

Novel Coiled-Coil Cell Division Factor ZapB Stimulates Z Ring Assembly and Cell Division

DEFF Research Database (Denmark)

Ebersbach, Gitte; Galli, Elizabeth; Møller-Jensen, Jakob

2008-01-01

Formation of the Z ring is the first known event in bacterial cell division. However, it is not yet known how the assembly and contraction of the Z ring is regulated. Here, we identify a novel cell division factor ZapB in Escherichia coli that simultaneously stimulates Z ring assembly and cell...... division. Deletion of zapB resulted in delayed cell division and the formation of ectopic Z rings and spirals whereas overexpression of ZapB resulted in nucleoid condensation and aberrant cell divisions. Localization of ZapB to the divisome depended on FtsZ but not FtsA, ZipA or FtsI and ZapB interacted...... with FtsZ in a bacterial two-hybrid analysis. The simultaneous inactivation of FtsA and ZipA prevented Z ring assembly and ZapB localization. Time lapse microscopy showed that ZapB-GFP is present at mid-cell in a pattern very similar to that of FtsZ. Cells carrying a zapB deletion and the ftsZ84ts allele...

An Analytical Evaluation of Spall Suppression of Impulsively Loaded Aluminum Panels Based on a One Dimensional Stress Wave Propagation Model.

Science.gov (United States)

1984-03-01

continued support in this research work. The author also wishes to thank Mr. Ronald E. Musante , Mr. Anthony P. Lee and the staff of FMC Corporation’s...West Point, New York 10996 8. Mr. R. E. Musante Manager, Armor Design Group Ordnance Division FMC Corporation California 90041 1105 Coleman Ave., Box

XIX Tactical Air Command and Ultra: Patton’s Force Enhancers in the 1944 Campaign in France

Science.gov (United States)

2000-06-01

forces in Montargis, Eddy did “keep going,” and his 4th Armored Division drove forty miles to the outskirts of Troyes , defeating the German forces there...then proceeded to Reims. Further to the south, XII Corps traveled from Troyes to Vitry-le-Francois with little difficulty, and then crossed the Marne

Strategic Landpower and the Arabian Gulf

Science.gov (United States)

2013-01-01

1st Armored Division, based in Fort Bliss , Texas, has been aligned with US Central Command and has played an important role in the Eager Lion...Trainers,” Washington Post, June 27, 2013. 46 Tim Ripley, Middle East Airpower in the 21st Century (South Yorkshire, UK: Pen and Sword, 2010), 173, 188

Podcast: The Electronic Crimes Division

Science.gov (United States)

Sept 26, 2016. Chris Lukas, the Special Agent in Charge of the Electronic Crimes Division within the OIG's Office of Investigations talks about computer forensics, cybercrime in the EPA and his division's role in criminal investigations.

Development of a remote handling system for replacement of armor tiles in the Fusion Experimental Reactor

International Nuclear Information System (INIS)

Adachi, J.; Kakudate, S.; Oka, K.; Seki, M.

1995-01-01

The armor tiles of the Fusion Experimental Reactor (FER) planned by JAERI are categorized as scheduled maintenance components, since they are damaged by severe heat and particle loads from the plasma during operation. A remote handling system is thus required to replace a large number of tiles rapidly in the highly activated reactor. However, the simple teaching-playback method cannot be adapted to this system because of deflection of the tiles caused by thermal deformation and so on. We have developed a control system using visual feedback control to adapt to this deflection and an end-effector for a single arm. We confirm their performance in tests. (orig.)

Division of Integrity and Materials

International Nuclear Information System (INIS)

Zdarek, J.

1995-01-01

The organization structure is described of the Division of Integrity and Materials, Institute of Nuclear Research plc, Rez, and the main fields of their activities given. Listed are the major research projects of the Division in 1994. (Z.S.)

2016 T Division Lightning Talks

Energy Technology Data Exchange (ETDEWEB)

Ramsey, Marilyn Leann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Adams, Luke Clyde [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Ferre, Gregoire Robing [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Grantcharov, Vesselin [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Iaroshenko, Oleksandr [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Krishnapriyan, Aditi [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Kurtakoti, Prajvala Kishore [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Le Thien, Minh Quan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Lim, Jonathan Ng [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Low, Thaddeus Song En [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Lystrom, Levi Aaron [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Ma, Xiaoyu [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Nguyen, Hong T. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Pogue, Sabine Silvia [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Orandle, Zoe Ann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Reisner, Andrew Ray [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Revard, Benjamin Charles [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Roy, Julien [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Sandor, Csanad [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Slavkova, Kalina Polet [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Weichman, Kathleen Joy [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Wu, Fei [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Yang, Yang [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division

2016-11-29

These are the slides for all of the 2016 T Division lightning talks. There are 350 pages worth of slides from different presentations, all of which cover different topics within the theoretical division at Los Alamos National Laboratory (LANL).

Analytical Chemistry Division's sample transaction system

International Nuclear Information System (INIS)

Stanton, J.S.; Tilson, P.A.

1980-10-01

The Analytical Chemistry Division uses the DECsystem-10 computer for a wide range of tasks: sample management, timekeeping, quality assurance, and data calculation. This document describes the features and operating characteristics of many of the computer programs used by the Division. The descriptions are divided into chapters which cover all of the information about one aspect of the Analytical Chemistry Division's computer processing

Mallow Fiber-Reinforced Epoxy Composites in Multilayered Armor for Personal Ballistic Protection

Science.gov (United States)

Nascimento, Lucio Fábio Cassiano; Louro, Luis Henrique Leme; Monteiro, Sergio Neves; Lima, Édio Pereira; da Luz, Fernanda Santos

2017-10-01

Lighter and less expensive polymer composites reinforced with natural fibers have been investigated as possible components of a multilayered armor system (MAS) for personal protection against high-velocity ammunition. Their ballistic performance was consistently found comparable with that of conventional Kevlar® synthetic aramid fiber. Among the numerous existing natural fibers with the potential for reinforcing polymer composites to replace Kevlar® in MAS, mallow fiber has not been fully investigated. Thus, the objective of this work is to evaluate the ballistic performance of epoxy composites reinforced with 30 vol.% of aligned mallow fibers as a second MAS layer backing a front ceramic plate. The results using high-velocity 7.62 ammunition show a similar indentation to a Kevlar® layer with the same thickness. An impedance matching calculation supports the similar ballistic performance of mallow fiber composite and Kevlar®. Reduced MAS costs associated with the mallow fiber composite are practical advantages over Kevlar®.

Optical Code-Division Multiple-Access and Wavelength Division Multiplexing: Hybrid Scheme Review

OpenAIRE

P. Susthitha Menon; Sahbudin Shaari; Isaac A.M. Ashour; Hesham A. Bakarman

2012-01-01

Problem statement: Hybrid Optical Code-Division Multiple-Access (OCDMA) and Wavelength-Division Multiplexing (WDM) have flourished as successful schemes for expanding the transmission capacity as well as enhancing the security for OCDMA. However, a comprehensive review related to this hybrid system are lacking currently. Approach: The purpose of this paper is to review the literature on OCDMA-WDM overlay systems, including our hybrid approach of one-dimensional coding of SAC OCDMA with WDM si...

Dissolution of methane bubbles with hydrate armoring in deep ocean conditions

Science.gov (United States)

Kovalchuk, Margarita; Socolofsky, Scott

2017-11-01

The deep ocean is a storehouse of natural gas. Methane bubble moving upwards from marine sediments may become trapped in gas hydrates. It is uncertain precisely how hydrate armoring affects dissolution, or mass transfer from the bubble to the surrounding water column. The Texas A&M Oilspill Calculator was used to simulate a series of gas bubble dissolution experiments conducted in the United States Department of Energy National Energy Technology Laboratory High Pressure Water Tunnel. Several variations of the mass transfer coefficient were calculated based on gas or hydrate phase solubility and clean or dirty bubble correlations. Results suggest the mass transfer coefficient may be most closely modeled with gas phase solubility and dirty bubble correlation equations. Further investigation of hydrate bubble dissolution behavior will refine current numeric models which aid in understanding gas flux to the atmosphere and plumes such as oil spills. Research funded in part by the Texas A&M University 2017 Undergraduate Summer Research Grant and a Grant from the Methane Gas Hydrates Program of the US DOE National Energy Technology Laboratory.

Chemical Technology Division annual technical report 1997

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-06-01

The Chemical Technology (CMT) Division is a diverse technical organization with principal emphases in environmental management and development of advanced energy sources. The Division conducts research and development in three general areas: (1) development of advanced power sources for stationary and transportation applications and for consumer electronics, (2) management of high-level and low-level nuclear wastes and hazardous wastes, and (3) electrometallurgical treatment of spent nuclear fuel. The Division also performs basic research in catalytic chemistry involving molecular energy resources, mechanisms of ion transport in lithium battery electrolytes, and the chemistry of technology-relevant materials and electrified interfaces. In addition, the Division operates the Analytical Chemistry Laboratory, which conducts research in analytical chemistry and provides analytical services for programs at Argonne National Laboratory (ANL) and other organizations. Technical highlights of the Division`s activities during 1997 are presented.

Lightning Talks 2015: Theoretical Division

Energy Technology Data Exchange (ETDEWEB)

Shlachter, Jack S. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2015-11-25

This document is a compilation of slides from a number of student presentations given to LANL Theoretical Division members. The subjects cover the range of activities of the Division, including plasma physics, environmental issues, materials research, bacterial resistance to antibiotics, and computational methods.

Developmental control of cell division

NARCIS (Netherlands)

Boxem, M. (Mike)

2002-01-01

During development of multicellular organisms, cell divisions need to be coordinated with the developmental program of the entire organism. Although the mechanisms that drive cells through the division cycle are well understood, very little is known about the pathways that link extracellular signals

An Investigation of Three Extremity Armor Systems: Determination of Physiological, Biomechanical, and Physical Performance Effects and Quantification of Body Area Coverage

Science.gov (United States)

2012-03-19

Fragmentation Protective Body Armor, had a filler made of ballistic nylon, which was sealed in a waterproof , vinyl envelope. As the name indicates...toe-off and peak braking and propulsive forces. GRF is a distributed force that acts over the entire surface of the foot or the shoe that is in...Catlin, M. J., & Dressendorfer, R. H. (1979). The effect of shoe weight on the energy cost of running [Abstract]. Medicine and Science in Sports

Division of household tasks and financial management

NARCIS (Netherlands)

Antonides, G.

2011-01-01

Both the standard economic model and bargaining theory make predictions about financial management and the division of household labor between household partners. Using a large Internet survey, we have tested several predictions about task divisions reported by Dutch household partners. The division

medico-legal perspectives in history

African Journals Online (AJOL)

Various legal codes dealing with medical malpractice existed in Egypt, Mesopotamia, China, Islam, Greece, Rome, Persia and India. The first documented Code of Laws ever used by human civilisation in, for example, Mesopotamia is to be found from the Law Code of Hammurabi – a textual source of evidence concerning ...

E-Division activities report

International Nuclear Information System (INIS)

Barschall, H.H.

1981-07-01

This report describes some of the activities in E (Experimental Physics) Division during the past year. E-Division carries out research and development in areas related to the missions of the Laboratory. Many of the activities are in pure and applied atomic and nuclear physics and in material science. In addition this report describes work on accelerators, microwaves, plasma diagnostics, determination of atmospheric oxygen and of nitrogen in tissue

External Quality Assessment for the Detection of Measles Virus by Reverse Transcription-PCR Using Armored RNA.

Directory of Open Access Journals (Sweden)

Dong Zhang

Full Text Available In recent years, nucleic acid tests for detection of measles virus RNA have been widely applied in laboratories belonging to the measles surveillance system of China. An external quality assessment program was established by the National Center for Clinical Laboratories to evaluate the performance of nucleic acid tests for measles virus. The external quality assessment panel, which consisted of 10 specimens, was prepared using armored RNAs, complex of noninfectious MS2 bacteriophage coat proteins encapsulated RNA of measles virus, as measles virus surrogate controls. Conserved sequences amplified from a circulating measles virus strain or from a vaccine strain were encapsulated into these armored RNAs. Forty-one participating laboratories from 15 provinces, municipalities, or autonomous regions that currently conduct molecular detection of measles virus enrolled in the external quality assessment program, including 40 measles surveillance system laboratories and one diagnostic reagent manufacturer. Forty laboratories used commercial reverse transcription-quantitative PCR kits, with only one laboratory applying a conventional PCR method developed in-house. The results indicated that most of the participants (38/41, 92.7% were able to accurately detect the panel with 100% sensitivity and 100% specificity. Although a wide range of commercially available kits for nucleic acid extraction and reverse transcription polymerase chain reaction were used by the participants, only two false-negative results and one false-positive result were generated; these were generated by three separate laboratories. Both false-negative results were obtained with tests performed on specimens with the lowest concentration (1.2 × 104 genomic equivalents/mL. In addition, all 18 participants from Beijing achieved 100% sensitivity and 100% specificity. Overall, we conclude that the majority of the laboratories evaluated have reliable diagnostic capacities for the detection

Chemical Sciences Division: Annual report 1992

International Nuclear Information System (INIS)

1993-10-01

The Chemical Sciences Division (CSD) is one of twelve research Divisions of the Lawrence Berkeley Laboratory, a Department of Energy National Laboratory. The CSD is composed of individual groups and research programs that are organized into five scientific areas: Chemical Physics, Inorganic/Organometallic Chemistry, Actinide Chemistry, Atomic Physics, and Physical Chemistry. This report describes progress by the CSD for 1992. Also included are remarks by the Division Director, a description of work for others (United States Office of Naval Research), and appendices of the Division personnel and an index of investigators. Research reports are grouped as Fundamental Interactions (Photochemical and Radiation Sciences, Chemical Physics, Atomic Physics) or Processes and Techniques (Chemical Energy, Heavy-Element Chemistry, and Chemical Engineering Sciences)

Insights into the Mechanisms of Chloroplast Division

Directory of Open Access Journals (Sweden)

Yamato Yoshida

2018-03-01

Full Text Available The endosymbiosis of a free-living cyanobacterium into an ancestral eukaryote led to the evolution of the chloroplast (plastid more than one billion years ago. Given their independent origins, plastid proliferation is restricted to the binary fission of pre-existing plastids within a cell. In the last 25 years, the structure of the supramolecular machinery regulating plastid division has been discovered, and some of its component proteins identified. More recently, isolated plastid-division machineries have been examined to elucidate their structural and mechanistic details. Furthermore, complex studies have revealed how the plastid-division machinery morphologically transforms during plastid division, and which of its component proteins play a critical role in generating the contractile force. Identifying the three-dimensional structures and putative functional domains of the component proteins has given us hints about the mechanisms driving the machinery. Surprisingly, the mechanisms driving plastid division resemble those of mitochondrial division, indicating that these division machineries likely developed from the same evolutionary origin, providing a key insight into how endosymbiotic organelles were established. These findings have opened new avenues of research into organelle proliferation mechanisms and the evolution of organelles.

Armored brain in patients with hydrocephalus after shunt surgery: review of the literatures.

Science.gov (United States)

Taha, Mahmoud M

2012-01-01

Armored brain or chronic calcified subdural hematoma is a rare complication of cerebrospinal fluid diversion with few cases reported in the literature. Seventeen patients with this pathology have been published. A complete review of the literatures regarding this topic has been collected and discussed. The author also presents a 12- year old boy with triventricular hydrocephalus who had undergone ventriculoperitoneal medium pressure shunt system since birth. The patient presented to our clinic with a 2-year history of seizures. The patient was conscious and without neurological deficits on examination. Computed tomography of the brain showed bilateral high density mass with surface calcification. X ray skull and MRI confirmed the calcified subdural hematoma bilaterally. We preferred conservative treatment and the patient continued his antiepileptic treatment. At one year follow up, the patient had the same neurological state. The case highlights the importance of frequent follow up CT brain after shunt surgery.

Energy Technology Division research summary 2001

International Nuclear Information System (INIS)

2001-01-01

The Energy Technology Division provides materials and engineering technology support to a wide range of programs important to the U.S. Department of Energy. As shown on the preceding page, the Division is organized into eight sections, four with concentrations in the materials area and four in engineering technology. Materials expertise includes fabrication, mechanical properties, corrosion, friction and lubrication, and irradiation effects. Our major engineering strengths are in heat and mass flow, sensors and instrumentation, nondestructive testing, transportation, and electromechanics and superconductivity applications. The Division Safety Coordinator, Environmental Compliance Officer, Quality Assurance Representative, Financial Administrator, and Communication Coordinator report directly to the Division Director. The Division Director is personally responsible for cultural diversity and is a member of the Laboratory-wide Cultural Diversity Advisory Committee. This Overview highlights some major ET research areas. Research related to the operational safety of commercial light water nuclear reactors (LWRs) for the U.S. Nuclear Regulatory Commission (NRC) remains a significant area of interest for the Division. We currently have programs on environmentally assisted cracking, steam generator integrity, and the integrity of high-burnup fuel during loss-of-coolant accidents. The bulk of the NRC research work is carried out by three ET sections: Corrosion and Mechanics of Materials; Irradiation Performance; and Sensors, Instrumentation, and Nondestructive Evaluation

The 1988 Leti Division progress report

International Nuclear Information System (INIS)

Anon.

1988-01-01

The 1988 progress report of the CEA's LETI Division (Division of Electronics, Technology and Instrumentation, France) is presented. The missions of LETI Division involve military and nuclear applications of electronics and fundamental research. The research programs developed in 1988 are the following: materials and components, non-volatile silicon memories, silicon-over-insulator, integrated circuits technologies, common experimental laboratory (opened to the European community), mass memories, photodetectors, micron sensors and flat screens [fr

Preliminary in Vivo Evaluation of a Hybrid Armored Vascular Graft Combining Electrospinning and Additive Manufacturing Techniques

Directory of Open Access Journals (Sweden)

Cristiano Spadaccio

2016-01-01

Full Text Available In this study, we tested in vivo effectiveness of a previously developed poly-L-lactide/poly-8-caprolactone armored vascular graft releasing heparin. This bioprosthesis was designed in order to overcome the main drawbacks of tissue-engineered vascular grafts, mainly concerning poor mechanical properties, thrombogenicity, and endothelialization. The bioprosthesis was successfully implanted in an aortic vascular reconstruction model in rabbits. All grafts implanted were patent at four weeks postoperatively and have been adequately populated by endogenous cells without signs of thrombosis or structural failure and with no need of antiplatelet therapy. The results of this preliminary study might warrant for further larger controlled in vivo studies to further confirm these findings.

Energy Technology Division research summary - 1999.

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-31

The Energy Technology Division provides materials and engineering technology support to a wide range of programs important to the US Department of Energy. As shown on the preceding page, the Division is organized into ten sections, five with concentrations in the materials area and five in engineering technology. Materials expertise includes fabrication, mechanical properties, corrosion, friction and lubrication, and irradiation effects. Our major engineering strengths are in heat and mass flow, sensors and instrumentation, nondestructive testing, transportation, and electromechanics and superconductivity applications. The Division Safety Coordinator, Environmental Compliance Officers, Quality Assurance Representative, Financial Administrator, and Communication Coordinator report directly to the Division Director. The Division Director is personally responsible for cultural diversity and is a member of the Laboratory-wide Cultural Diversity Advisory Committee. The Division's capabilities are generally applied to issues associated with energy production, transportation, utilization, or conservation, or with environmental issues linked to energy. As shown in the organization chart on the next page, the Division reports administratively to the Associate Laboratory Director (ALD) for Energy and Environmental Science and Technology (EEST) through the General Manager for Environmental and Industrial Technologies. While most of our programs are under the purview of the EEST ALD, we also have had programs funded under every one of the ALDs. Some of our research in superconductivity is funded through the Physical Research Program ALD. We also continue to work on a number of nuclear-energy-related programs under the ALD for Engineering Research. Detailed descriptions of our programs on a section-by-section basis are provided in the remainder of this book.

Reverse Evolution of Armor Plates in the Threespine Stickleback

Science.gov (United States)

Kitano, J.; Bolnick, D.I.; Beauchamp, D.A.; Mazur, M.M.; Mori, S.; Nakano, T.; Peichel, C.L.

2008-01-01

Faced with sudden environmental changes, animals must either adapt to novel environments or go extinct. Thus, study of the mechanisms underlying rapid adaptation is crucial not??only for the understanding of natural evolutionary processes but also for the understanding of human-induced evolutionary change, which is an increasingly important problem [1-8]. In the present study, we demonstrate that the frequency of completely plated threespine stickleback fish (Gasterosteus aculeatus) has increased in an urban freshwater lake (Lake Washington, Seattle, Washington) within the last 40 years. This is a dramatic example of "reverse evolution," [9] because the general evolutionary trajectory is toward armor-plate reduction in freshwater sticklebacks [10]. On the basis of our genetic studies and simulations, we propose that the most likely cause of reverse evolution is increased selection for the completely plated morph, which we suggest could result from higher levels of trout predation after a sudden increase in water transparency during the early 1970s. Rapid evolution was facilitated by the existence of standing allelic variation in Ectodysplasin (Eda), the gene that underlies the major plate-morph locus [11]. The Lake Washington stickleback thus provides a novel example of reverse evolution, which is probably caused by a change in allele frequency at the major plate locus in response to a changing predation regime. ?? 2008 Elsevier Ltd. All rights reserved.

75 FR 78268 - Draft NIJ Selection and Application Guide to Ballistic-Resistant Body Armor for Law Enforcement...

Science.gov (United States)

2010-12-15

...In an effort to obtain comments from interested parties, the U.S. Department of Justice, Office of Justice Programs, National Institute of Justice (NIJ) will make available to the general public the draft ``NIJ Selection and Application Guide to Ballistic-Resistant Body Armor for Law Enforcement, Corrections, and Public Safety.'' The opportunity to provide comments on this document is open to industry technical representatives, criminal justice agencies and organizations, research, development and scientific communities, and all other stakeholders and interested parties. Those individuals wishing to obtain and provide comments on the draft document under consideration are directed to the following Web site: http://www.justnet.org.

Physics division annual report 2006.

Energy Technology Data Exchange (ETDEWEB)

Glover, J.; Physics

2008-02-28

This report highlights the activities of the Physics Division of Argonne National Laboratory in 2006. The Division's programs include the operation as a national user facility of ATLAS, the Argonne Tandem Linear Accelerator System, research in nuclear structure and reactions, nuclear astrophysics, nuclear theory, investigations in medium-energy nuclear physics as well as research and development in accelerator technology. The mission of nuclear physics is to understand the origin, evolution and structure of baryonic matter in the universe--the core of matter, the fuel of stars, and the basic constituent of life itself. The Division's research focuses on innovative new ways to address this mission.

Division of Analytical Chemistry, 1998

DEFF Research Database (Denmark)

Hansen, Elo Harald

1999-01-01

The article recounts the 1998 activities of the Division of Analytical Chemistry (DAC- formerly the Working Party on Analytical Chemistry, WPAC), which body is a division of the Federation of European Chemical Societies (FECS). Elo Harald Hansen is the Danish delegate, representing The Danish...... Chemical Society/The Society for Analytical Chemistry....

Current programmes of Metallurgy Division (1991)

International Nuclear Information System (INIS)

1991-01-01

Current research and development programmes of the Metallurgy Division are listed under the headings: 1)Thrust Areas, 2)High Temperature Materials Section, 3)Chemical Metallurgy Section, 4)Metallurgical Thermochemistry Section, 5)Physical Metallurgy Section, 6)Mechanical Metallurgy Section, 7)Corrosion Metallurgy Section, 8)Electrochemical Science and Technology Section, 9)Ceramics Section, and 10)Fabrication and Maintenance Group. A list of equipment in the Division and a list of sciientific personnel of the Division are also given. (M.G.B.)

Natural Mallow Fiber-Reinforced Epoxy Composite for Ballistic Armor Against Class III-A Ammunition

Science.gov (United States)

Nascimento, Lucio Fabio Cassiano; Holanda, Luane Isquerdo Ferreira; Louro, Luis Henrique Leme; Monteiro, Sergio Neves; Gomes, Alaelson Vieira; Lima, Édio Pereira

2017-10-01

Epoxy matrix composites reinforced with up to 30 vol pct of continuous and aligned natural mallow fibers were for the first time ballistic tested as personal armor against class III-A 9 mm FMJ ammunition. The ballistic efficiency of these composites was assessed by measuring the dissipated energy and residual velocity after the bullet perforation. The results were compared to those in similar tests of aramid fabric (Kevlar™) commonly used in vests for personal protections. Visual inspection and scanning electron microscopy analysis of impact-fractured samples revealed failure mechanisms associated with fiber pullout and rupture as well as epoxy cracking. As compared to Kevlar™, the mallow fiber composite displayed practically the same ballistic efficiency. However, there is a reduction in both weight and cost, which makes the mallow fiber composites a promising material for personal ballistic protection.

Thermal shock fracture of graphite armor plate under the heat load of plasma disruption

International Nuclear Information System (INIS)

Horie, Tomoyoshi; Seki, Masahiro; Ohmori, Junji

1989-01-01

Experiments on the thermal shock brittle fracture of graphite plates were performed. Thermal loading which simulated a plasma disruption was produced by an electron beam facility. Pre-cracks produced on the surface propagated to the inside of the specimen even if the thermal stress on the surface was compressive. Two mechanisms are possible to produce tensile stress around the crack tip under thermal shock conditions. Temperature, thermal stress, and the stress intensity factor for the specimen were analyzed based on the finite element method for various heating conditions. The trend of experimental results under the asymmetric heating agrees qualitatively with the analytical results. This phenomenon is important for the design of plasma facing components made of graphite. Establishment of a lifetime prediction procedure including fatigue, fatigue crack growth, and brittle fracture is needed for graphite armors. (orig.)

Chemical and Laser Sciences Division annual report 1989

International Nuclear Information System (INIS)

Haines, N.

1990-06-01

The Chemical and Laser Sciences Division Annual Report includes articles describing representative research and development activities within the Division, as well as major programs to which the Division makes significant contributions

Beryllium armored mockups for fusion high flux application

International Nuclear Information System (INIS)

Gervash, A.; Giniyatulin, R.; Mazul, I.; Watson, R.

1998-01-01

One of the main requirements to use Be as a candidate for plasma facing component in ITER is providing a reliable joint between Be and Cu-alloy heat sink structure. In this work authors present the results of recent activity on this way. To create Be/CuCrZr joints the unique fast e-beam brazing technology was developed in Russia. The numbers of Be/CuCrZr mock-ups were manufactured in Efremov Institute by fast e-beam brazing using Cu-Sn-In-Ni brazing alloy. These mock-ups were tested by Sandia Laboratory at the EBTS electron beam facility. The goals of the tests were to define the allowable dimensions of the armour tiles for the heat loads of more than 10 MW/m 2 , to find the limit of bond strength for the Be/CuCrZr joint and response to heat loads and to estimate the life time of the brazed tiles by thermo-cyclic testing. The screening and thermal fatigue results are presented. With the aim to check the applicability of developed fast brazing process to DS-Cu alloy (GlidCop) the actively cooled mock-up produced by fast brazing Be onto GlidCop structure was manufactured and tested in Efremov Institute, main results are discussed. Summarizing testing data authors show that the CuCrZr or DS-Cu heat sink armored with beryllium can survive high heat fluxes (≥10 MW/m 2 ) during thousand heating/cooling cycles without serious damaging in the armour material and its joint. (author)

Division of Information Technology - Overview

International Nuclear Information System (INIS)

Szlachciak, J.

2007-01-01

I have a great pleasure to introduce the youngest division in our Institute, namely the Division of Information Technology. The division was created in 2005, but this is the first time when it reports its activities. The main purpose of creation was a better management of al IT activities in different departments, lowering IT costs and increase security over all computer systems used be the Institute. Although we have started with small human resources, we have received a big support from other departments. Special thanks go to the Department of Detectors and Nuclear Electronics. Our division handles many service-oriented activities. In daily work we answer many IT-related questions and deliver our help in order to solve hardware and software problems. The style of our work can be described as a result-oriented one. Here is the list of our biggest achievements: · construction of the server room; · implementation of two electronic bank systems; · development of the dynamic hardware and software inventory system; · development of the Scientific Activity Database. (author)

Viscoelastic shock wave in ballistic gelatin behind soft body armor.

Science.gov (United States)

Liu, Li; Fan, Yurun; Li, Wei

2014-06-01

Ballistic gelatins are widely used as a surrogate of biological tissue in blunt trauma tests. Non-penetration impact tests of handgun bullets on the 10wt% ballistic gelatin block behind soft armor were carried out in which a high-speed camera recorded the crater׳s movement and pressure sensors imbedded in the gelatin block recorded the pressure waves at different locations. The observed shock wave attenuation indicates the necessity of considering the gelatin׳s viscoelasticity. A three-element viscoelastic constitutive model was adopted, in which the relevant parameters were obtained via fitting the damping free oscillations at the beginning of the creep-mode of rheological measurement, and by examining the data of published split Hopkinson pressure bar (SHPB) experiments. The viscoelastic model is determined by a retardation time of 5.5×10(-5)s for high oscillation frequencies and a stress relaxation time of 2.0-4.5×10(-7)s for shock wave attenuation. Using the characteristic-line method and the spherical wave assumption, the propagation of impact pressure wave front and the subsequent unloading profile can be simulated using the experimental velocity boundary condition. The established viscoelastic model considerably improves the prediction of shock wave attenuation in the ballistic gelatin. Copyright © 2014 Elsevier Ltd. All rights reserved.

An examination of the stretching practices of Division I and Division III college football programs in the midwestern United States.

Science.gov (United States)

Judge, Lawrence W; Craig, Bruce; Baudendistal, Steve; Bodey, Kimberly J

2009-07-01

Research supports the use of preactivity warm-up and stretching, and the purpose of this study was to determine whether college football programs follow these guidelines. Questionnaires designed to gather demographic, professional, and educational information, as well as specific pre- and postactivity practices, were distributed via e-mail to midwestern collegiate programs from NCAA Division I and III conferences. Twenty-three male coaches (12 from Division IA schools and 11 from Division III schools) participated in the study. Division I schools employed certified strength coaches (CSCS; 100%), whereas Division III schools used mainly strength coordinators (73%), with only 25% CSCS. All programs used preactivity warm-up, with the majority employing 2-5 minutes of sport-specific jogging/running drills. Pre stretching (5-10 minutes) was performed in 19 programs (91%), with 2 (9%) performing no pre stretching. Thirteen respondents used a combination of static/proprioceptive neuromuscular facilitation/ballistic and dynamic flexibility, 5 used only dynamic flexibility, and 1 used only static stretching. All 12 Division I coaches used stretching, whereas only 9 of the 11 Division III coaches did (p = 0.22). The results indicate that younger coaches did not use pre stretching (p = 0.30). The majority of the coaches indicated that they did use post stretching, with 11 of the 12 Division I coaches using stretching, whereas only 5 of the 11 Division III coaches used stretching postactivity (p = 0.027). Divisional results show that the majority of Division I coaches use static-style stretching (p = 0.049). The results of this study indicate that divisional status, age, and certification may influence how well research guidelines are followed. Further research is needed to delineate how these factors affect coaching decisions.

Energy Technology Division research summary 2004

International Nuclear Information System (INIS)

Poeppel, R. B.; Shack, W. J.

2004-01-01

The Energy Technology (ET) Division provides materials and engineering technology support to a wide range of programs important to the US Department of Energy (DOE). The Division's capabilities are generally applied to technical issues associated with energy systems, biomedical engineering, transportation, and homeland security. Research related to the operational safety of commercial light water nuclear reactors (LWRs) for the US Nuclear Regulatory Commission (NRC) remains another significant area of interest for the Division. The pie chart below summarizes the ET sources of funding for FY 2004

1998 Chemical Technology Division Annual Technical Report.

Energy Technology Data Exchange (ETDEWEB)

Ackerman, J.P.; Einziger, R.E.; Gay, E.C.; Green, D.W.; Miller, J.F.

1999-08-06

The Chemical Technology (CMT) Division is a diverse technical organization with principal emphases in environmental management and development of advanced energy sources. The Division conducts research and development in three general areas: (1) development of advanced power sources for stationary and transportation applications and for consumer electronics, (2) management of high-level and low-level nuclear wastes and hazardous wastes, and (3) electrometallurgical treatment of spent nuclear fuel. The Division also performs basic research in catalytic chemistry involving molecular energy resources, mechanisms of ion transport in lithium battery electrolytes, and the chemistry of technology-relevant materials. In addition, the Division operates the Analytical Chemistry Laboratory, which conducts research in analytical chemistry and provides analytical services for programs at Argonne National Laboratory (ANL) and other organizations. Technical highlights of the Division's activities during 1998 are presented.

Chemical Technology Division annual technical report 1997

International Nuclear Information System (INIS)

1998-06-01

The Chemical Technology (CMT) Division is a diverse technical organization with principal emphases in environmental management and development of advanced energy sources. The Division conducts research and development in three general areas: (1) development of advanced power sources for stationary and transportation applications and for consumer electronics, (2) management of high-level and low-level nuclear wastes and hazardous wastes, and (3) electrometallurgical treatment of spent nuclear fuel. The Division also performs basic research in catalytic chemistry involving molecular energy resources, mechanisms of ion transport in lithium battery electrolytes, and the chemistry of technology-relevant materials and electrified interfaces. In addition, the Division operates the Analytical Chemistry Laboratory, which conducts research in analytical chemistry and provides analytical services for programs at Argonne National Laboratory (ANL) and other organizations. Technical highlights of the Division's activities during 1997 are presented

2002 Chemical Engineering Division annual report

International Nuclear Information System (INIS)

Lewis, D.; Graziano, D.; Miller, J. F.

2003-01-01

The Chemical Engineering Division is one of eight engineering research divisions within Argonne National Laboratory, one of the U.S. government's oldest and largest research laboratories. The University of Chicago oversees the laboratory on behalf of the U.S. Department of Energy (DOE). Argonne's mission is to conduct basic scientific research, to operate national scientific facilities, to enhance the nation's energy resources, and to develop better ways to manage environmental problems. Argonne has the further responsibility of strengthening the nation's technology base by developing innovative technology and transferring it to industry. The Division is a diverse early-stage engineering organization, specializing in the treatment of spent nuclear fuel, development of advanced electrochemical power sources, and management of both high- and low-level nuclear wastes. Although this work is often indistinguishable from basic research, our efforts are directed toward the practical devices and processes that are covered by Argonne's mission. Additionally, the Division operates the Analytical Chemistry Laboratory; Environment, Safety, and Health Analytical Chemistry services; and Dosimetry and Radioprotection services, which provide a broad range of analytical services to Argonne and other organizations. The Division is multidisciplinary. Its people have formal training as ceramists; physicists; material scientists; electrical, mechanical, chemical, and nuclear engineers; and chemists. They have experience working in academia; urban planning; and the petroleum, aluminum, and automotive industries. Their skills include catalysis, ceramics, electrochemistry, metallurgy, nuclear magnetic resonance spectroscopy, and petroleum refining, as well as the development of nuclear waste forms, batteries, and high-temperature superconductors. Our wide-ranging expertise finds ready application in solving energy and environmental problems. Division personnel are frequently called on by

Energy Division progress report, fiscal years 1994--1995

Energy Technology Data Exchange (ETDEWEB)

Moser, C.I. [ed.

1996-06-01

At ORNL, the Energy Division`s mission is to provide innovative solutions to energy and related issues of national and global importance through interdisciplinary research and development. Its goals and accomplishments are described in this progress report for FY 1994 and FY 1995. The Division`s expenditures in FY 1995 totaled 44.9 million. Sixty percent of the divisions work was supported by the US DOE. Other significant sponsors include the US DOT, the US DOD, other federal agencies, and some private organizations. The Division`s programmatic activities cover three main areas: (1) analysis and assessment, (2) transportation systems, and (3) energy use and delivery technologies. Analysis and assessment activities involve energy and resource analysis, preparation of environmental assessments and impact statements, and impact statements, research on emergency preparedness, analysis of energy and environmental needs in developing countries, and transportation analysis. Transportation systems research seeks to improve the quality of both civilian and military transportation efforts. Energy use and delivery technologies focus on building equipment, building envelopes, (walls, roofs, attics, and materials), improvement of energy efficiency in buildings, and electric power systems.

Digital Arithmetic: Division Algorithms

DEFF Research Database (Denmark)

Montuschi, Paolo; Nannarelli, Alberto

2017-01-01

Division is one of the basic arithmetic operations supported by every computer system. The operation can be performed and implemented by either hardware or software, or by a combination of the two. Although division is not as frequent as addition and multiplication, nowadays, most processors impl...... significant hardware resources and is more suitable for software implementation on the existing multiply units. The purpose of this entry is to provide an introductory survey using a presentation style suitable for the interested non-specialist readers as well....

Power Dissipation in Division

DEFF Research Database (Denmark)

Liu, Wei; Nannarelli, Alberto

2008-01-01

A few classes of algorithms to implement division in hardware have been used over the years: division by digit-recurrence, by reciprocal approximation by iterative methods and by polynomial approximation. Due to the differences in the algorithms, a comparison among their implementation in terms o...... of performance and precision is sometimes hard to make. In this work, we use power dissipation and energy consumption as metrics to compare among those different classes of algorithms. There are no previous works in the literature presenting such a comparison....

Impact of the surface quality on the thermal shock performance of beryllium armor tiles for first wall applications

Energy Technology Data Exchange (ETDEWEB)

Spilker, B., E-mail: b.spilker@fz-juelich.de; Linke, J.; Pintsuk, G.; Wirtz, M.

2016-11-01

Highlights: • Different surface qualities of S-65 beryllium are tested under high heat flux conditions. • After 1000 thermal shocks, the loaded area exhibits a crucial destruction. • Stress accelerated grain boundary oxidation/dynamic embrittlement effects are linked to the thermal shock performance of beryllium. • Thermally induced cracks form between 1 and 10 pulses and grow wider and deeper between 10 and 100 pulses. • Thermally induced cracks form and propagate independently from surface grooves and the surface quality. - Abstract: Beryllium will be applied as first wall armor material in ITER. The armor has to sustain high steady state and transient power fluxes. For transient events like edge localized modes, these transient power fluxes rise up to 1.0 GW m{sup −2} with a duration of 0.5–0.75 ms in the divertor region and a significant fraction of this power flux is deposited on the first wall as well. In the present work, the reference beryllium grade for the ITER first wall application S-65 was prepared with various surface conditions and subjected to transient power fluxes (thermal shocks) with ITER relevant loading parameters. After 1000 thermal shocks, a crucial destruction of the entire loaded area was observed and linked to the stress accelerated grain boundary oxidation (SAGBO)/dynamic embrittlement (DE) effect. Furthermore, the study revealed that the majority of the thermally induced cracks formed between 1 and 10 pulses and then grew wider and deeper with increasing pulse number. The surface quality did not influence the cracking behavior of beryllium in any detectable way. However, the polished surface demonstrated the highest resistance against the observed crucial destruction mechanism.

Important projects of the Division

International Nuclear Information System (INIS)

2008-01-01

In this chapter important projects of the Division for Radiation Safety, NPP Decommissioning and Radwaste Management of the VUJE, a. s. are presented. Division for Radiation Safety, NPP Decommissioning and Radwaste Management has successfully carried out variety of significant projects. The most significant projects that were realised, are implemented and possible future projects are introduced in the following part of presentation.

Stationary infinitely divisible processes

DEFF Research Database (Denmark)

Barndorff-Nielsen, Ole E.

Several recent strands of work has led to the consideration of various types of continuous time stationary and infinitely divisible processes. A review of these types, with some new results, is presented.......Several recent strands of work has led to the consideration of various types of continuous time stationary and infinitely divisible processes. A review of these types, with some new results, is presented....

FtsZ-less prokaryotic cell division as well as FtsZ- and dynamin-less chloroplast and non-photosynthetic plastid division

Directory of Open Access Journals (Sweden)

Shin-Ya eMiyagishima

2014-09-01

Full Text Available The chloroplast division machinery is a mixture of a stromal FtsZ-based complex descended from a cyanobacterial ancestor of chloroplasts and a cytosolic dynamin-related protein (DRP 5B-based complex derived from the eukaryotic host. Molecular genetic studies have shown that each component of the division machinery is normally essential for normal chloroplast division. However, several exceptions have been found. In the absence of the FtsZ ring, nonphotosynthetic plastids are able to proliferate, likely by elongation and budding. Depletion of DRP5B impairs, but does not stop chloroplast division. Chloroplasts in glaucophytes, which possesses a peptidoglycan (PG layer, divide without DRP5B. Certain parasitic eukaryotes possess nonphotosynthetic plastids of secondary endosymbiotic origin, but neither FtsZ nor DRP5B is encoded in their genomes. Elucidation of the FtsZ- and/or DRP5B-less chloroplast division mechanism will lead to a better understanding of the function and evolution of the chloroplast division machinery and the finding of the as-yet-unknown mechanism that is likely involved in chloroplast division. Recent studies have shown that FtsZ was lost from a variety of prokaryotes, many of which lost PG by regressive evolution. In addition, even some of the FtsZ-bearing bacteria are able to divide when FtsZ and PG are depleted experimentally. In some cases, alternative mechanisms for cell division, such as budding by an increase of the cell surface-to-volume ratio, are proposed. Although PG is believed to have been lost from chloroplasts other than in glaucophytes, there is some indirect evidence for the existence of PG in chloroplasts. Such information is also useful for understanding how nonphotosynthetic plastids are able to divide in FtsZ-depleted cells and the reason for the retention of FtsZ in chloroplast division. Here we summarize information to facilitate analyses of FtsZ- and/or DRP5B-less chloroplast and nonphotosynthetic plastid

The lacrimal system: diagnosis, management, and surgery

National Research Council Canada - National Science Library

Cohen, Adam J; Mercandetti, Michael; Brazzo, Brian G

2006-01-01

... and techniques presented represent the state of the art of lacrimal diagnosis and surgery. There is mention of lacrimal infection dating back to the Code of Hammurabi in 2250 BC, but it was not until the late 1800s that real progress began to be made. Toti, an ENT surgeon in Florence, Italy, described external dacryocystorhinostomy (DCR) with turb...

Earth Sciences Division collected abstracts: 1979

International Nuclear Information System (INIS)

Henry, A.L.; Schwartz, L.L.

1980-01-01

This report is a compilation of abstracts of papers, internal reports, and talks presented during 1979 at national and international meetings by members of the Earth Sciences Division, Lawrence Livermore Laboratory. The arrangement is alphabetical (by author). For a given report, a bibliographic reference appears under the name of each coauthor, but the abstract iself is given only under the name of the first author or the first Earth Sciences Division author. A topical index at the end of the report provides useful cross references, while indicating major areas of research interest in the Earth Sciences Division

Chemical Sciences Division annual report 1994

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-06-01

The division is one of ten LBL research divisions. It is composed of individual research groups organized into 5 scientific areas: chemical physics, inorganic/organometallic chemistry, actinide chemistry, atomic physics, and chemical engineering. Studies include structure and reactivity of critical reaction intermediates, transients and dynamics of elementary chemical reactions, and heterogeneous and homogeneous catalysis. Work for others included studies of superconducting properties of high-{Tc} oxides. In FY 1994, the division neared completion of two end-stations and a beamline for the Advanced Light Source, which will be used for combustion and other studies. This document presents summaries of the studies.

Theoretical Division annual report, FY 1975

International Nuclear Information System (INIS)

Carruthers, P.A.

1976-02-01

This report presents an overview of the activities in the Theoretical Division and a summary of research highlights during FY 1975. It is intended to inform a wide audience about the theoretical work of the LASL and, therefore, contains introductory material which places recent advances in a broader context. The report is organized into two special interest reports: reactor safety research and the Advanced Research Committee, and 11 reports from the T-Division group leaders on the work of their respective groups. Main interests and responsibilities are outlined including the relationship of the group's work to the work of other T-Division groups and other divisions at the Laboratory. The description of research highlights for FY 1975 explains in a fairly simple, straightforward manner the major recent advances and their significance. Each group report is followed by a publication list for FY 1975 (330 references) and a list of talks given outside the Laboratory (140 references). 29 figures

The History of Metals and Ceramics Division

Energy Technology Data Exchange (ETDEWEB)

Craig, D.F.

1999-01-01

The division was formed in 1946 at the suggestion of Dr. Eugene P. Wigner to attack the problem of the distortion of graphite in the early reactors due to exposure to reactor neutrons, and the consequent radiation damage. It was called the Metallurgy Division and assembled the metallurgical and solid state physics activities of the time which were not directly related to nuclear weapons production. William A. Johnson, a Westinghouse employee, was named Division Director in 1946. In 1949 he was replaced by John H Frye Jr. when the Division consisted of 45 people. He was director during most of what is called the Reactor Project Years until 1973 and his retirement. During this period the Division evolved into three organizational areas: basic research, applied research in nuclear reactor materials, and reactor programs directly related to a specific reactor(s) being designed or built. The Division (Metals and Ceramics) consisted of 204 staff members in 1973 when James R. Weir, Jr., became Director. This was the period of the oil embargo, the formation of the Energy Research and Development Administration (ERDA) by combining the Atomic Energy Commission (AEC) with the Office of Coal Research, and subsequent formation of the Department of Energy (DOE). The diversification process continued when James O. Stiegler became Director in 1984, partially as a result of the pressure of legislation encouraging the national laboratories to work with U.S. industries on their problems. During that time the Division staff grew from 265 to 330. Douglas F. Craig became Director in 1992.

Theoretical physics division

International Nuclear Information System (INIS)

Anon.

1980-01-01

Research activities of the theoretical physics division for 1979 are described. Short summaries are given of specific research work in the following fields: nuclear structure, nuclear reactions, intermediate energy physics, elementary particles [fr

Atmospheric and Geophysical Sciences Division: Program report, FY 1987

International Nuclear Information System (INIS)

1988-05-01

In 1988 the Atmospheric and Geophysical Sciences Division began its 15th year as a division. As the Division has grown over the years, its modeling capabilities have expanded to include a broad range of time and space scales ranging from hours to years, and from kilometers to global, respectively. For this report, we have chosen to show a subset of results from several projects to illustrate the breadth, depth, and diversity of the modeling activities that are a major part of the Division's research, development, and application efforts. In addition, the recent reorganization of the Division, including the merger of another group with the Division, is described, and the budget, personnel, models, and publications are reviewed. 95 refs., 26 figs., 2 tabs

Recent High Heat Flux Tests on W-Rod-Armored Mockups

International Nuclear Information System (INIS)

Nygren, Richard E.; Youchison, Dennis L.; McDonald, Jimmie M.; Lutz, Thomas J.; Miszkiel, Mark E.

2000-01-01

In the authors initial high heat flux tests on small mockups armored with W rods, done in the small electron beam facility (EBTS) at Sandia National Laboratories, the mockups exhibited excellent thermal performance. However, to reach high heat fluxes, they reduced the heated area to only a portion (approximately25%) of the sample. They have now begun tests in their larger electron beam facility, EB 1200, where the available power (1.2 MW) is more than enough to heat the entire surface area of the small mockups. The initial results indicate that, at a given power, the surface temperatures of rods in the EB 1200 tests is somewhat higher than was observed in the EBTS tests. Also, it appears that one mockup (PW-10) has higher surface temperatures than other mockups with similar height (10mm) W rods, and that the previously reported values of absorbed heat flux on this mockup were too high. In the tests in EB 1200 of a second mockup, PW-4, absorbed heat fluxes of approximately22MW/m 2 were reached but the corresponding surface temperatures were somewhat higher than in EBTS. A further conclusion is that the simple 1-D model initially used in evaluating some of the results from the EBTS testing was not adequate, and 3-D thermal modeling will be needed to interpret the results

Couples’ Attitudes, Childbirth, and the Division of Labor

NARCIS (Netherlands)

Jansen, Miranda; Liefbroer, Aart C.

2006-01-01

In this article, the authors examine effects of partners’ attitudes on the timing of the birth of a first child, the division of domestic labor, the division of child care, and the division of paid labor of couples. They use data from the Panel Study of Social Integration in the Netherlands, which

Division of labour in the yeast

DEFF Research Database (Denmark)

Wloch-Salamon, Dominika M.; Fisher, Roberta May; Regenberg, Birgitte

2017-01-01

. Saccharomyces cerevisiae displays several phenotypes that could be considered a division of labour, including quiescence, apoptosis and biofilm formation, but they have not been explicitly treated as such. We discuss each of these examples, using a definition of division of labour that involves phenotypic...... variation between cells within a population, cooperation between cells performing different tasks and maximization of the inclusive fitness of all cells involved. We then propose future research directions and possible experimental tests using S. cerevisiae as a model organism for understanding the genetic...... mechanisms and selective pressures that can lead to the evolution of the very first stages of a division of labour....

Radioactive Waste and Clean-up Division

International Nuclear Information System (INIS)

Collard, G.

2001-01-01

The main objectives of the Radioactive Waste and Clean-up division of SCK-CEN are outlined. The division's programme consists of research, development and demonstration projects and aims to contribute to the objectives of Agenda 21 on sustainable development in the field of radioactive waste and rehabilitation of radioactively contaminated sites

Responses to Three USARIEM Job Analysis Questionnaires (JAQs) Conducted with Cavalry Scouts and Armor Crewmen (MOSs 19D and 19K)

Science.gov (United States)

2016-11-18

gun for one fire command 56 24 Boxes of rounds loaded for the .50 Cal Machine Gun on an Abrams Tank 56 25 Mean estimates of time spent by 19Ds...Number of rounds loaded for one fire command 55 22 Total boxes of rounds loaded for .50 cal machine gun on an Abrams tank 56 23 Number of Soldiers...and 19K MOSs, respectively). A total o f 8,580 Army calvary scouts and 6,613 armor crewmen in the USA Army as of May or June of 2014 were invited

Energy Technology Division research summary -- 1994

Energy Technology Data Exchange (ETDEWEB)

1994-09-01

Research funded primarily by the NRC is directed toward assessing the roles of cyclic fatigue, intergranular stress corrosion cracking, and irradiation-assisted stress corrosion cracking on failures in light water reactor (LWR) piping systems, pressure vessels, and various core components. In support of the fast reactor program, the Division has responsibility for fuel-performance modeling and irradiation testing. The Division has major responsibilities in several design areas of the proposed International Thermonuclear Experimental Reactor (ITER). The Division supports the DOE in ensuring safe shipment of nuclear materials by providing extensive review of the Safety Analysis Reports for Packaging (SARPs). Finally, in the nuclear area they are investigating the safe disposal of spent fuel and waste. In work funded by DOE`s Energy Efficiency and Renewable Energy, the high-temperature superconductivity program continues to be a major focal point for industrial interactions. Coatings and lubricants developed in the division`s Tribology Section are intended for use in transportation systems of the future. Continuous fiber ceramic composites are being developed for high-performance heat engines. Nondestructive testing techniques are being developed to evaluate fiber distribution and to detect flaws. A wide variety of coatings for corrosion protection of metal alloys are being studied. These can increase lifetimes significant in a wide variety of coal combustion and gasification environments.

Atmospheric and Geophysical Sciences Division Program Report, 1988--1989

Energy Technology Data Exchange (ETDEWEB)

1990-06-01

In 1990, the Atmospheric and Geophysical Sciences Division begins its 17th year as a division. As the Division has grown over the years, its modeling capabilities have expanded to include a broad range of time and space scales ranging from hours to decades and from local to global. Our modeling is now reaching out from its atmospheric focus to treat linkages with the oceans and the land. In this report, we describe the Division's goal and organizational structure. We also provide tables and appendices describing the Division's budget, personnel, models, and publications. 2 figs., 1 tab.

Conceptual thermal-mechanical design of the TFTR first wall armor against neutral beam impingement

International Nuclear Information System (INIS)

Chi, J.W.H.; Flaherty, R.

1976-01-01

The Tokamak Fusion Test Reactor (TFTR) is designed to operate in a pulsed mode with relatively low duty cycles. Each pulse consists of a short plasma heat-up period, a reaction period, followed by a relatively long cooldown period. Plasma heating is accomplished by ohmic heating by a current induced change in the magnetically linked ohmic heating coils, followed by neutral beam injection for further preheat and the initiation of fusion reactions. During normal operation, the bulk of the neutral beam energy will be absorbed by the plasma, while the remainder will impinge on the vacuum vessel wall. The amount of thermal energy deposited on an unprotected wall is expected to be excessive, limiting the frequency of pulses and requiring frequent wall replacement. A faulted condition would cause penetration of an unprotected wall. As a consequence, a wall armoring (or liner) concept was developed to protect the vacuum vessel wall and to permit ease of liner replacement

The stem cell division theory of cancer.

Science.gov (United States)

López-Lázaro, Miguel

2018-03-01

All cancer registries constantly show striking differences in cancer incidence by age and among tissues. For example, lung cancer is diagnosed hundreds of times more often at age 70 than at age 20, and lung cancer in nonsmokers occurs thousands of times more frequently than heart cancer in smokers. An analysis of these differences using basic concepts in cell biology indicates that cancer is the end-result of the accumulation of cell divisions in stem cells. In other words, the main determinant of carcinogenesis is the number of cell divisions that the DNA of a stem cell has accumulated in any type of cell from the zygote. Cell division, process by which a cell copies and separates its cellular components to finally split into two cells, is necessary to produce the large number of cells required for living. However, cell division can lead to a variety of cancer-promoting errors, such as mutations and epigenetic mistakes occurring during DNA replication, chromosome aberrations arising during mitosis, errors in the distribution of cell-fate determinants between the daughter cells, and failures to restore physical interactions with other tissue components. Some of these errors are spontaneous, others are promoted by endogenous DNA damage occurring during quiescence, and others are influenced by pathological and environmental factors. The cell divisions required for carcinogenesis are primarily caused by multiple local and systemic physiological signals rather than by errors in the DNA of the cells. As carcinogenesis progresses, the accumulation of DNA errors promotes cell division and eventually triggers cell division under permissive extracellular environments. The accumulation of cell divisions in stem cells drives not only the accumulation of the DNA alterations required for carcinogenesis, but also the formation and growth of the abnormal cell populations that characterize the disease. This model of carcinogenesis provides a new framework for understanding the

Evaluation of dose attenuation factor of armored car against radiation accidents

International Nuclear Information System (INIS)

Sato, Tatsuhiko; Fujii, Katsutoshi; Murayama, Takashi

2002-03-01

The Tokyo Fire Department developed an armored car against radiation accidents. The car is covered by lead shields for attenuating dose from gamma rays. Dose from neutrons also can be attenuated by pouring water into tanks attached to the surface of the car. However, dose attenuation factors of the radiation shields had been determined by an estimation of single-layer shield, and more precise evaluation of multi-layer shield was required. By request from the Tokyo Fire Department, a precise evaluation of the dose attenuation in multi-layer shield was carried out. The evaluation was made by a Monte Carlo radiation transport simulation code MCNP4B for the shields used in the front, side and back of the car. Three types of the radiation sources ( 252 Cf as a neutron source, 60 Co as a gamma ray source, and radiation source corresponding to the JCO criticality accident) were considered in the calculation. Benchmark experiments using neutron and gamma ray sources were also performed for ensuring the evaluation method. As a result, it was found out that doses of neutron and gamma ray were attenuated to approximately 10% and 25% by the thickest shield, respectively. These values were close to the ones which had already obtained by the estimation of single-layer shield. (author)

Biology Division progress report, October 1, 1991--September 30, 1993

Energy Technology Data Exchange (ETDEWEB)

Hartman, F.C.; Cook, J.S.

1993-10-01

This Progress Report summarizes the research endeavors of the Biology Division of the Oak Ridge National Laboratory during the period October 1, 1991, through September 30, 1993. The report is structured to provide descriptions of current activities and accomplishments in each of the Division`s major organizational units. Lists of information to convey the entire scope of the Division`s activities are compiled at the end of the report.

Radix-16 Combined Division and Square Root Unit

DEFF Research Database (Denmark)

Nannarelli, Alberto

2011-01-01

Division and square root, based on the digitrecurrence algorithm, can be implemented in a combined unit. Several implementations of combined division/square root units have been presented mostly for radices 2 and 4. Here, we present a combined radix-16 unit obtained by overlapping two radix-4...... result digit selection functions, as it is normally done for division only units. The latency of the unit is reduced by retiming and low power methods are applied as well. The proposed unit is compared to a radix-4 combined division/square root unit, and to a radix-16 unit, obtained by cascading two...

Chemical Technology Division Annual Report 2000

International Nuclear Information System (INIS)

Lewis, D.; Gay, E. C.; Miller, J. F.; Einziger, R. E.; Green, D. W.

2001-01-01

The Chemical Technology Division (CMT) is one of eight engineering research divisions within Argonne National Laboratory (ANL), one of the U.S. government's oldest and largest research laboratories. The University of Chicago oversees the laboratory on behalf of the U.S. Department of Energy (DOE). Argonne's mission is to conduct basic scientific research, to operate national scientific facilities, to enhance the nation's energy resources, and to develop better ways to manage environmental problems. Argonne has the further responsibility of strengthening the nation's technology base through developing industrial technology and transferring that technology to industry. The Chemical Technology Division is a diverse early-stage engineering organization, specializing in the treatment of spent nuclear fuel, development of advanced power sources, and management of both high- and low-level nuclear wastes. Although this work is often indistinguishable from basic research, our efforts are directed toward the practical devices and processes that are covered by ANL's mission. Additionally, the Division operates the Analytical Chemistry Laboratory, which provides a broad range of analytical services to ANL and other organizations. The Division is multi-disciplinary. Its people have formal training as ceramists; physicists; material scientists; electrical, mechanical, chemical, and nuclear engineers; and chemists. They have experience working in academia, urban planning, and the petroleum, aluminum, and automotive industries. Their skills include catalysis, ceramics, electrochemistry, metallurgy, nuclear magnetic resonance spectroscopy, and petroleum refining, as well as the development of nuclear waste forms, batteries, and high-temperature superconductors. In this annual report we present an overview of the technical programs together with representative highlights. The report is not intended to be comprehensive or encyclopedic, but to serve as an indication of the condition

Materials Sciences Division 1990 annual report

Energy Technology Data Exchange (ETDEWEB)

1990-12-31

This report is the Materials Sciences Division`s annual report. It contains abstracts describing materials research at the National Center for Electron Microscopy, and for research groups in metallurgy, solid-state physics, materials chemistry, electrochemical energy storage, electronic materials, surface science and catalysis, ceramic science, high tc superconductivity, polymers, composites, and high performance metals.

Earth Sciences Division, collected abstracts-1977

International Nuclear Information System (INIS)

Quitiquit, W.A.; Ledbetter, G.P.; Henry, A.L.

1978-01-01

This report is a compilation of abstracts of papers, internal reports, and talks presented during 1977 at national and international meetings by members of the Earth Sciences Division, Lawrence Livermore Laboratory. It is arranged alphabetically by author and includes a cross-reference by subject indicating the areas of research interest of the Earth Sciences Division

Nuclear size and cell division delay

International Nuclear Information System (INIS)

Bird, R.P.

1986-01-01

Radiation-induced division delay has been linked to damage at the nuclear envelope. Further, cells in G 2 phase are drastically arrested by high LET radiation such that single particles traversing cell nuclei may produce measurable division delay. A modest effort was initiated using two related cell lines of different size, near-diploid cells and near-tetraploid cells of Chinese hamster origin, to compare their sensitivity for radiation-induced division delay. If the nuclear surface is the critical target, then a larger nuclear cross-section presented to an alpha-particle beam should exhibit delay induced by a lesser particle fluence. Preliminary estimates of the extent of delay in asynchronous cultures following low doses of gamma-irradiation or of alpha-irradiation were made by in-situ observation of the time of onset of mitosis and by fixation and staining of cultures to determine the mitotic index as a function of time after irradiation. The basic approach to evaluating division delay will be to use Colecemid to accumulate mitotic cells over a period of time

Parallel optoelectronic trinary signed-digit division

Science.gov (United States)

Alam, Mohammad S.

1999-03-01

The trinary signed-digit (TSD) number system has been found to be very useful for parallel addition and subtraction of any arbitrary length operands in constant time. Using the TSD addition and multiplication modules as the basic building blocks, we develop an efficient algorithm for performing parallel TSD division in constant time. The proposed division technique uses one TSD subtraction and two TSD multiplication steps. An optoelectronic correlator based architecture is suggested for implementation of the proposed TSD division algorithm, which fully exploits the parallelism and high processing speed of optics. An efficient spatial encoding scheme is used to ensure better utilization of space bandwidth product of the spatial light modulators used in the optoelectronic implementation.

Radiochemistry Division annual progress report : 1992

International Nuclear Information System (INIS)

Natarajan, V.; Godbole, S.V.; Iyer, R.H.

1994-01-01

The research and development activities of the Radiochemistry Division during 1992 are briefly described in the form of individual summaries grouped under the headings: 1) Nuclear Chemistry, 2) Actinide Chemistry, 3) Spectroscopy, and 4) Instrumentation. A list of publications numbering 95 by the scientific staff of the Division is also included in the report. (author). 35 figs., 56 tabs

The Natural Armor of Fish: An Exploration of a Biological Composite

Science.gov (United States)

Murcia, Sandra C.

In the search for advanced structural materials, scientists are finding inspiration from materials in nature and biological composites. The need for lighter protective materials has directed attention to armored skins, which possess a combination of flexibility, puncture resistance and capacity for energy dissipation. This rare combination of properties is found in the armored skin of modern fish, and achieved by overlapping scales with exceptional specific strength and toughness. The main objectives of this research were to develop new understanding on the constituent layers and lamination patterns of elasmoid scales from teleost fish, and understand their importance to the mechanical properties relevant to armor performance. The investigation consists of five aims that address properties of the scales as a structural material, the spatial variations over the body of fish, the microstructure and properties of the individual layers, and the design and performance of the interface between these layers. An exploration of scales from Cyprinus carpio showed that the fracture resistance of elasmoid fish scales is largely dependent on the anatomical position and the corresponding microstructure. Elasmoid scales were found to consist of three principle layers, including the external highly mineralized limiting layer (LL), as well as the external (EE) and internal (IE) elasmodine, which consist of a number of lamina (or plies) of unidirectional type I collagen fibrils. While the fracture resistance increased with scale thickness, it was highly correlated with the number of plies in the elasmodine and ratio of mineralized plies in the EE. Furthermore, the hierarchical structure of the scales and the molecular level bonds were found to be of importance. Removal of the intra molecular water enabled inter-peptide bonding of the collagen fibrils, which increased the strength and elastic modulus. Furthermore, mineral crystals at the intra-fibrilar spaces impeded the formation of

Division of Labor

KAUST Repository

Oke, Muse; Zaher, Manal S.; Hamdan, Samir

2014-01-01

The first assignment of DNA polymerases at the eukaryotic replication fork was possible after the in vitro reconstitution of the simian virus 40 (SV40) replication system. In this system, DNA polymerase α (Pol α) provides both leading and lagging strands with RNA-DNA primers that are extended by DNA polymerase δ (Pol δ). Extrapolating the architecture of the replication fork from the SV40 model system to an actual eukaryotic cell has been challenged by the discovery of a third DNA polymerase in Saccharomyces cerevisiae, DNA polymerase ε (Pol ε). A division of labor has been proposed for the eukaryotic replication fork whereby Pol ε replicates the leading strand and Pol δ replicates the lagging strand. However, an alternative model of unequal division of labor in which Pol δ can still participate in leading-strand synthesis is plausible.

Division of Labor

KAUST Repository

Oke, Muse

2014-09-12

The first assignment of DNA polymerases at the eukaryotic replication fork was possible after the in vitro reconstitution of the simian virus 40 (SV40) replication system. In this system, DNA polymerase α (Pol α) provides both leading and lagging strands with RNA-DNA primers that are extended by DNA polymerase δ (Pol δ). Extrapolating the architecture of the replication fork from the SV40 model system to an actual eukaryotic cell has been challenged by the discovery of a third DNA polymerase in Saccharomyces cerevisiae, DNA polymerase ε (Pol ε). A division of labor has been proposed for the eukaryotic replication fork whereby Pol ε replicates the leading strand and Pol δ replicates the lagging strand. However, an alternative model of unequal division of labor in which Pol δ can still participate in leading-strand synthesis is plausible.

Physics division. Progress report, January 1, 1995--December 31, 1996

International Nuclear Information System (INIS)

Stewart, M.; Bacon, D.S.; Aine, C.J.; Bartsch, R.R.

1997-10-01

This issue of the Physics Division Progress Report describes progress and achievements in Physics Division research during the period January 1, 1995-December 31, 1996. The report covers the five main areas of experimental research and development in which Physics Division serves the needs of Los Alamos National Laboratory and the nation in applied and basic sciences: (1) biophysics, (2) hydrodynamic physics, (3) neutron science and technology, (4) plasma physics, and (5) subatomic physics. Included in this report are a message from the Division Director, the Physics Division mission statement, an organizational chart, descriptions of the research areas of the five groups in the Division, selected research highlights, project descriptions, the Division staffing and funding levels for FY95-FY97, and a list of publications and presentations

Physics division. Progress report, January 1, 1995--December 31, 1996

Energy Technology Data Exchange (ETDEWEB)

Stewart, M.; Bacon, D.S.; Aine, C.J.; Bartsch, R.R. [eds.] [comps.] [and others

1997-10-01

This issue of the Physics Division Progress Report describes progress and achievements in Physics Division research during the period January 1, 1995-December 31, 1996. The report covers the five main areas of experimental research and development in which Physics Division serves the needs of Los Alamos National Laboratory and the nation in applied and basic sciences: (1) biophysics, (2) hydrodynamic physics, (3) neutron science and technology, (4) plasma physics, and (5) subatomic physics. Included in this report are a message from the Division Director, the Physics Division mission statement, an organizational chart, descriptions of the research areas of the five groups in the Division, selected research highlights, project descriptions, the Division staffing and funding levels for FY95-FY97, and a list of publications and presentations.

Nuclear Chemistry Division annual report FY83

International Nuclear Information System (INIS)

Struble, G.

1983-01-01

The purpose of the annual reports of the Nuclear Chemistry Division is to provide a timely summary of research activities pursued by members of the Division during the preceding year. Throughout, details are kept to a minimum; readers desiring additional information are encouraged to read the referenced documents or contact the authors. The Introduction presents an overview of the Division's scientific and technical programs. Next is a section of short articles describing recent upgrades of the Division's major facilities, followed by sections highlighting scientific and technical advances. These are grouped under the following sections: nuclear explosives diagnostics; geochemistry and environmental sciences; safeguards technology and radiation effect; and supporting fundamental science. A brief overview introduces each section. Reports on research supported by a particular program are generally grouped together in the same section. The last section lists the scientific, administrative, and technical staff in the Division, along with visitors, consultants, and postdoctoral fellows. It also contains a list of recent publications and presentations. Some contributions to the annual report are classified and only their abstracts are included in this unclassified portion of the report (UCAR-10062-83/1); the full article appears in the classified portion (UCAR-10062-83/2)

The ACS-NUCL Division 50th Anniversary: Introduction

Energy Technology Data Exchange (ETDEWEB)

Hobart, David E. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-01-10

The ACS Division of Nuclear Chemistry and Technology was initiated in 1955 as a subdivision of the Division of Industrial and Engineering Chemistry. Probationary divisional status was lifted in 1965. The Division’s first symposium was held in Denver in 1964 and it is fitting that we kicked-off the 50th Anniversary in Denver in the spring of 2015. Listed as a small ACS Division with only about 1,000 members, NUCL’s impact over the past fifty years has been remarkable. National ACS meetings have had many symposia sponsored or cosponsored by NUCL that included Nobel Laureates, U.S. Senators, other high-ranking officials and many students as speakers. The range of subjects has been exceptional as are the various prestigious awards established by the Division. Of major impact has been the past 30 years of the NUCL Nuclear Chemistry Summer Schools to help fill the void of qualified nuclear scientists and technicians. In celebrating the 50th Anniversary we honor the past, celebrate the present and shape the future of the Division and nuclear science and technology. To celebrate this auspicious occasion a commemorative lapel pin has been designed for distribution to NUCL Division members.

24 CFR 4.36 - Action by the Ethics Law Division.

Science.gov (United States)

2010-04-01

... violation is material, the Ethics Law Division shall consider the following factors, as applicable: (1) The... 24 Housing and Urban Development 1 2010-04-01 2010-04-01 false Action by the Ethics Law Division... the Ethics Law Division. (a) After review of the Inspector General's report, the Ethics Law Division...

Lead from the center. How to manage divisions dynamically.

Science.gov (United States)

Raynor, M E; Bower, J L

2001-05-01

Conventional wisdom holds that a company's divisions should be given almost total autonomy--especially under conditions of uncertainty--because they are closer to emerging technologies, customers, and competitors than corporate headquarters could ever be. But research from Michael Raynor and Joseph Bower suggests that the corporate office should be more, not less, directive in turbulent markets. Rapid changes in an industry make it difficult to predict where and when synergies among divisions might emerge. With so many possibilities and such uncertainty, companies can't afford to sacrifice their ability to flexibly execute business strategy. Corporate headquarters must play an active role in defining the scope of division-level strategy, the authors say, so that divisions do not act in ways that undermine opportunities to collaborate in the future. But neither can companies afford to sacrifice the competitiveness of their divisions as stand-alone businesses. In creating corporate-level strategic flexibility, a corporate office must balance the need for divisional autonomy now with the potential need for cooperation in the future. Through an examination of four corporations--Sprint, WPP, Teradyne, and Viacom--the authors challenge traditional approaches to diversification in which a company's divisions are either related (they share resources and collaborate) or unrelated (they compete for resources and operate as stand-alone businesses). They argue that companies should adopt a dynamic approach to cooperation among divisions, enabling varying degrees of relatedness between divisions depending on strategic circumstances. The authors offer four tactics to help executives manage divisions dynamically.

Reactor Engineering Division Material for World Wide Web Pages

International Nuclear Information System (INIS)

1996-01-01

This document presents the home page of the Reactor Engineering Division of Argonne National Laboratory. This WWW site describes the activities of the Division, an introduction to its wide variety of programs and samples of the results of research by people in the division

Medical Sciences Division report for 1993

Energy Technology Data Exchange (ETDEWEB)

1993-12-31

This year`s Medical Sciences Division (MSD) Report is organized to show how programs in our division contribute to the core competencies of Oak Ridge Institute for Science and Education (ORISE). ORISE`s core competencies in education and training, environmental and safety evaluation and analysis, occupational and environmental health, and enabling research support the overall mission of the US Department of Energy (DOE).

Medical Sciences Division report for 1993

International Nuclear Information System (INIS)

1993-01-01

This year's Medical Sciences Division (MSD) Report is organized to show how programs in our division contribute to the core competencies of Oak Ridge Institute for Science and Education (ORISE). ORISE's core competencies in education and training, environmental and safety evaluation and analysis, occupational and environmental health, and enabling research support the overall mission of the US Department of Energy (DOE)

Division of labour in the yeast: Saccharomyces cerevisiae.

Science.gov (United States)

Wloch-Salamon, Dominika M; Fisher, Roberta M; Regenberg, Birgitte

2017-10-01

Division of labour between different specialized cell types is a central part of how we describe complexity in multicellular organisms. However, it is increasingly being recognized that division of labour also plays an important role in the lives of predominantly unicellular organisms. Saccharomyces cerevisiae displays several phenotypes that could be considered a division of labour, including quiescence, apoptosis and biofilm formation, but they have not been explicitly treated as such. We discuss each of these examples, using a definition of division of labour that involves phenotypic variation between cells within a population, cooperation between cells performing different tasks and maximization of the inclusive fitness of all cells involved. We then propose future research directions and possible experimental tests using S. cerevisiae as a model organism for understanding the genetic mechanisms and selective pressures that can lead to the evolution of the very first stages of a division of labour. Copyright © 2017 John Wiley & Sons, Ltd. Copyright © 2017 John Wiley & Sons, Ltd.

15 CFR 950.8 - Satellite Data Services Division (SDSD).

Science.gov (United States)

2010-01-01

... 15 Commerce and Foreign Trade 3 2010-01-01 2010-01-01 false Satellite Data Services Division (SDSD... THE ENVIRONMENTAL DATA SERVICE ENVIRONMENTAL DATA AND INFORMATION § 950.8 Satellite Data Services Division (SDSD). The Satellite Data Services Division of the EDIS National Climatic Center provides...

Division of Agriculture

Science.gov (United States)

Department of Natural Resources logo, color scheme Department of Natural Resources Division of Agriculture Search Search DNR's site DNR State of Alaska Toggle main menu visibility Agriculture Home Programs Asset Disposals Alaska Caps Progam Board of Agriculture & Conservation Farm To School Program Grants

Quantitative regulation of B cell division destiny by signal strength.

Science.gov (United States)

Turner, Marian L; Hawkins, Edwin D; Hodgkin, Philip D

2008-07-01

Differentiation to Ab secreting and isotype-switched effector cells is tightly linked to cell division and therefore the degree of proliferation strongly influences the nature of the immune response. The maximum number of divisions reached, termed the population division destiny, is stochastically distributed in the population and is an important parameter in the quantitative outcome of lymphocyte responses. In this study, we further assessed the variables that regulate B cell division destiny in vitro in response to T cell- and TLR-dependent stimuli. Both the concentration and duration of stimulation were able to regulate the average maximum number of divisions undergone for each stimulus. Notably, a maximum division destiny was reached during provision of repeated saturating stimulation, revealing that an intrinsic limit to proliferation exists even under these conditions. This limit was linked directly to division number rather than time of exposure to stimulation and operated independently of the survival regulation of the cells. These results demonstrate that a B cell population's division destiny is regulable by the stimulatory conditions up to an inherent maximum value. Division destiny is a crucial parameter in regulating the extent of B cell responses and thereby also the nature of the immune response mounted.

Parkin suppresses Drp1-independent mitochondrial division

Energy Technology Data Exchange (ETDEWEB)

Roy, Madhuparna, E-mail: mroy17@jhmi.edu; Itoh, Kie, E-mail: kito5@jhmi.edu; Iijima, Miho, E-mail: miijima@jhmi.edu; Sesaki, Hiromi, E-mail: hsesaki@jhmi.edu

2016-07-01

The cycle of mitochondrial division and fusion disconnect and reconnect individual mitochondria in cells to remodel this energy-producing organelle. Although dynamin-related protein 1 (Drp1) plays a major role in mitochondrial division in cells, a reduced level of mitochondrial division still persists even in the absence of Drp1. It is unknown how much Drp1-mediated mitochondrial division accounts for the connectivity of mitochondria. The role of a Parkinson’s disease-associated protein—parkin, which biochemically and genetically interacts with Drp1—in mitochondrial connectivity also remains poorly understood. Here, we quantified the number and connectivity of mitochondria using mitochondria-targeted photoactivatable GFP in cells. We show that the loss of Drp1 increases the connectivity of mitochondria by 15-fold in mouse embryonic fibroblasts (MEFs). While a single loss of parkin does not affect the connectivity of mitochondria, the connectivity of mitochondria significantly decreased compared with a single loss of Drp1 when parkin was lost in the absence of Drp1. Furthermore, the loss of parkin decreased the frequency of depolarization of the mitochondrial inner membrane that is caused by increased mitochondrial connectivity in Drp1-knockout MEFs. Therefore, our data suggest that parkin negatively regulates Drp1-indendent mitochondrial division. -- Highlights: •A Drp1-mediated mechanism accounts for ∼95% of mitochondrial division. •Parkin controls the connectivity of mitochondria via a mechanism that is independent of Drp1. •In the absence of Drp1, connected mitochondria transiently depolarize. •The transient depolarization is independent of calcium signaling and uncoupling protein 2.

Parkin suppresses Drp1-independent mitochondrial division

International Nuclear Information System (INIS)

Roy, Madhuparna; Itoh, Kie; Iijima, Miho; Sesaki, Hiromi

2016-01-01

The cycle of mitochondrial division and fusion disconnect and reconnect individual mitochondria in cells to remodel this energy-producing organelle. Although dynamin-related protein 1 (Drp1) plays a major role in mitochondrial division in cells, a reduced level of mitochondrial division still persists even in the absence of Drp1. It is unknown how much Drp1-mediated mitochondrial division accounts for the connectivity of mitochondria. The role of a Parkinson’s disease-associated protein—parkin, which biochemically and genetically interacts with Drp1—in mitochondrial connectivity also remains poorly understood. Here, we quantified the number and connectivity of mitochondria using mitochondria-targeted photoactivatable GFP in cells. We show that the loss of Drp1 increases the connectivity of mitochondria by 15-fold in mouse embryonic fibroblasts (MEFs). While a single loss of parkin does not affect the connectivity of mitochondria, the connectivity of mitochondria significantly decreased compared with a single loss of Drp1 when parkin was lost in the absence of Drp1. Furthermore, the loss of parkin decreased the frequency of depolarization of the mitochondrial inner membrane that is caused by increased mitochondrial connectivity in Drp1-knockout MEFs. Therefore, our data suggest that parkin negatively regulates Drp1-indendent mitochondrial division. -- Highlights: •A Drp1-mediated mechanism accounts for ∼95% of mitochondrial division. •Parkin controls the connectivity of mitochondria via a mechanism that is independent of Drp1. •In the absence of Drp1, connected mitochondria transiently depolarize. •The transient depolarization is independent of calcium signaling and uncoupling protein 2.

Publications - Geospatial Data | Alaska Division of Geological &

Science.gov (United States)

from rocks collected in the Richardson mining district, Big Delta Quadrangle, Alaska: Alaska Division Island 2009 topography: Alaska Division of Geological & Geophysical Surveys Miscellaneous Publication , Geologic map of portions of the Livengood B-3, B-4, C-3, and C-4 quadrangles, Tolovana mining district

Biology Division progress report, October 1, 1993--September 30, 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-10-01

This Progress Report summarizes the research endeavors of the Biology Division of the Oak Ridge National Laboratory during the period October 1, 1993, through September 30, 1995. The report is structured to provide descriptions of current activities and accomplishments in each of the Division`s major organizational units. Lists of information to convey the entire scope of the Division`s activities are compiled at the end of the report. Attention is focused on the following research activities: molecular, cellular, and cancer biology; mammalian genetics and development; genome mapping program; and educational activities.

Biology and Medicine Division: Annual report 1986

International Nuclear Information System (INIS)

1987-04-01

The Biology and Medicine Division continues to make important contributions in scientific areas in which it has a long-established leadership role. For 50 years the Division has pioneered in the application of radioisotopes and charged particles to biology and medicine. There is a growing emphasis on cellular and molecular applications in the work of all the Division's research groups. The powerful tools of genetic engineering, the use of recombinant products, the analytical application of DNA probes, and the use of restriction fragment length polymorphic DNA are described and proposed for increasing use in the future

Biology and Medicine Division: Annual report 1986

Energy Technology Data Exchange (ETDEWEB)

1987-04-01

The Biology and Medicine Division continues to make important contributions in scientific areas in which it has a long-established leadership role. For 50 years the Division has pioneered in the application of radioisotopes and charged particles to biology and medicine. There is a growing emphasis on cellular and molecular applications in the work of all the Division's research groups. The powerful tools of genetic engineering, the use of recombinant products, the analytical application of DNA probes, and the use of restriction fragment length polymorphic DNA are described and proposed for increasing use in the future.

Mapping Urban Social Divisions

Directory of Open Access Journals (Sweden)

Susan Ball

2010-05-01

Full Text Available Against the background of increased levels of interest in space and images beyond the field of geography, this article (re- introduces earlier work on the semiotics of maps undertaken by geographers in the 1960s. The data limitations, purpose and cultural context in which a user interprets a map's codes and conventions are highlighted in this work, which remains relevant to the interpretation of maps—new and old—forty years later. By means of drawing on geography's contribution to the semiotics of maps, the article goes on to examine the concept of urban social divisions as represented in map images. Using a small number of map images, including two of the most widely known maps of urban social division in Europe and North America, the roles of context, data and purpose in the production and interpretation of maps are discussed. By presenting the examples chronologically the article shows that although advances in data collection and manipulation have allowed researchers to combine different social variables in maps of social division, and to interact with map images, work by geographers on the semiotics of maps is no less relevant today than when it was first proposed forty years ago. URN: urn:nbn:de:0114-fqs1002372

Nuclear Chemistry Division annual report FY83

Energy Technology Data Exchange (ETDEWEB)

Struble, G. (ed.)

1983-01-01

The purpose of the annual reports of the Nuclear Chemistry Division is to provide a timely summary of research activities pursued by members of the Division during the preceding year. Throughout, details are kept to a minimum; readers desiring additional information are encouraged to read the referenced documents or contact the authors. The Introduction presents an overview of the Division's scientific and technical programs. Next is a section of short articles describing recent upgrades of the Division's major facilities, followed by sections highlighting scientific and technical advances. These are grouped under the following sections: nuclear explosives diagnostics; geochemistry and environmental sciences; safeguards technology and radiation effect; and supporting fundamental science. A brief overview introduces each section. Reports on research supported by a particular program are generally grouped together in the same section. The last section lists the scientific, administrative, and technical staff in the Division, along with visitors, consultants, and postdoctoral fellows. It also contains a list of recent publications and presentations. Some contributions to the annual report are classified and only their abstracts are included in this unclassified portion of the report (UCAR-10062-83/1); the full article appears in the classified portion (UCAR-10062-83/2).

Reactor Engineering Division annual report

International Nuclear Information System (INIS)

1978-10-01

Research activities in the Division of Reactor Engineering in fiscal 1977 are described. Works of the Division are development of multi-purpose Very High Temperature Gas Cooled Reactor, fusion reactor engineering, and development of Liquid Metal Fast Breeder Reactor for Power Reactor and Nuclear Fuel Development Corporation. Contents of the report are nuclear data and group constants, theoretical method and code development, integral experiment and analysis, shielding, heat transfer and fluid dynamics, reactor and nuclear instrumentation, dynamics analysis and control method development, fusion reactor technology, and Committee on Reactor Physics. (Author)

Energy Technology Division research summary 1997

International Nuclear Information System (INIS)

1997-01-01

The Energy Technology Division provides materials and engineering technology support to a wide range of programs important to the US Department of Energy. As shown on the preceding page, the Division is organized into ten sections, five with concentrations in the materials area and five in engineering technology. Materials expertise includes fabrication, mechanical properties, corrosion, friction and lubrication, and irradiation effects. Our major engineering strengths are in heat and mass flow, sensors and instrumentation, nondestructive testing, transportation, and electromechanics and superconductivity applications. The Division Safety Coordinator, Environmental Compliance Officers, Quality Assurance Representative, Financial Administrator, and Communication Coordinator report directly to the Division Director. The Division Director is personally responsible for cultural diversity and is a member of the Laboratory-wide Cultural Diversity Advisory Committee. The Division's capabilities are generally applied to issues associated with energy production, transportation, utilization or conservation, or with environmental issues linked to energy. As shown in the organization chart on the next page, the Division reports administratively to the Associate Laboratory Director (ALD) for Energy and Environmental Science and Technology (EEST) through the General Manager for Environmental and Industrial Technologies. While most of our programs are under the purview of the EEST ALD, we also have had programs funded under every one of the ALDs. Some of our research in superconductivity is funded through the Physical Research Program ALD. We also continue to work on a number of nuclear-energy-related programs under the ALD for Engineering Research. Detailed descriptions of our programs on a section-by-section basis are provided in the remainder of this book. This Overview highlights some major trends. Research related to the operational safety of commercial light water nuclear

Energy Technology Division research summary 1997.

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-10-21

The Energy Technology Division provides materials and engineering technology support to a wide range of programs important to the US Department of Energy. As shown on the preceding page, the Division is organized into ten sections, five with concentrations in the materials area and five in engineering technology. Materials expertise includes fabrication, mechanical properties, corrosion, friction and lubrication, and irradiation effects. Our major engineering strengths are in heat and mass flow, sensors and instrumentation, nondestructive testing, transportation, and electromechanics and superconductivity applications. The Division Safety Coordinator, Environmental Compliance Officers, Quality Assurance Representative, Financial Administrator, and Communication Coordinator report directly to the Division Director. The Division Director is personally responsible for cultural diversity and is a member of the Laboratory-wide Cultural Diversity Advisory Committee. The Division's capabilities are generally applied to issues associated with energy production, transportation, utilization or conservation, or with environmental issues linked to energy. As shown in the organization chart on the next page, the Division reports administratively to the Associate Laboratory Director (ALD) for Energy and Environmental Science and Technology (EEST) through the General Manager for Environmental and Industrial Technologies. While most of our programs are under the purview of the EEST ALD, we also have had programs funded under every one of the ALDs. Some of our research in superconductivity is funded through the Physical Research Program ALD. We also continue to work on a number of nuclear-energy-related programs under the ALD for Engineering Research. Detailed descriptions of our programs on a section-by-section basis are provided in the remainder of this book. This Overview highlights some major trends. Research related to the operational safety of commercial light water

The exp-normal distribution is infinitely divisible

OpenAIRE

Pinelis, Iosif

2018-01-01

Let $Z$ be a standard normal random variable (r.v.). It is shown that the distribution of the r.v. $\\ln|Z|$ is infinitely divisible; equivalently, the standard normal distribution considered as the distribution on the multiplicative group over $\\mathbb{R}\\setminus\\{0\\}$ is infinitely divisible.

Division V: Commission 42: Close Binaries

Science.gov (United States)

Ribas, Ignasi; Richards, Mercedes T.; Rucinski, Slavek; Bradstreet, David H.; Harmanec, Petr; Kaluzny, Janusz; Mikolajewska, Joanna; Munari, Ulisse; Niarchos, Panagiotis; Olah, Katalin; Pribulla, Theodor; Scarfe, Colin D.; Torres, Guillermo

2015-08-01

Commission 42 (C42) co-organized, together with Commission 27 (C27) and Division V (Div V) as a whole, a full day of science and business sessions that were held on 24 August 2012. The program included time slots for discussion of business matters related to Div V, C27 and C42, and two sessions of 2 hours each devoted to science talks of interest to both C42 and C27. In addition, we had a joint session between Div IV and Div V motivated by the proposal to reformulate the division structure of the IAU and the possible merger of the two divisions into a new Div G. The current report gives an account of the matters discussed during the business session of C42.

Theoretical Division annual report, FY 1975. [LASL

Energy Technology Data Exchange (ETDEWEB)

Carruthers, P.A.

1976-02-01

This report presents an overview of the activities in the Theoretical Division and a summary of research highlights during FY 1975. It is intended to inform a wide audience about the theoretical work of the LASL and, therefore, contains introductory material which places recent advances in a broader context. The report is organized into two special interest reports: reactor safety research and the Advanced Research Committee, and 11 reports from the T-Division group leaders on the work of their respective groups. Main interests and responsibilities are outlined including the relationship of the group's work to the work of other T-Division groups and other divisions at the Laboratory. The description of research highlights for FY 1975 explains in a fairly simple, straightforward manner the major recent advances and their significance. Each group report is followed by a publication list for FY 1975 (330 references) and a list of talks given outside the Laboratory (140 references). 29 figures. (auth)

Nuclear Science Division, 1995--1996 annual report

International Nuclear Information System (INIS)

Poskanzer, A.M.

1997-02-01

This report describes the activities of the Nuclear Science Division (NSD) for the two-year period, January 1, 1995 to January 1, 1997. This was a time of major accomplishments for all research programs in the Division-many of which are highlighted in the reports of this document

Nuclear Science Division, 1995--1996 annual report

Energy Technology Data Exchange (ETDEWEB)

Poskanzer, A.M. [ed.

1997-02-01

This report describes the activities of the Nuclear Science Division (NSD) for the two-year period, January 1, 1995 to January 1, 1997. This was a time of major accomplishments for all research programs in the Division-many of which are highlighted in the reports of this document.

Safety and Health Division achievements during 40 years

International Nuclear Information System (INIS)

Noriah Mod Ali

2012-01-01

During her speech, presenter outlined several issues regarding on establishment of Safety and Health Division since 40 years. This division contain of 3 sub unit; Physical Safety Group, Medical Physic Group and Non-ionizing Radiation group (NIR). The objectives of this division to implement R and D activities and services regarding safety and radiological health also non-radiological to ensure public safety, environment and asset suit with obligations established by authorities, IAEA standards and regulations.(author)

Earth Sciences Division, collected abstracts, 1978

International Nuclear Information System (INIS)

Taasevigen, D.K.; Henry, A.L.; Madsen, S.K.

1979-01-01

Abstracts of papers, internal reports, and talks presented during 1978 at national and international meetings by members of the Earth Sciences Division of the Lawrence Livermore Laboratory are compiled. The arrangement is alphabetical (by author). For any given report, a bibliographic reference appears under the name of each coauthor. A topical index at the end provides useful cross references, while indicating major areas of research interest in the Earth Sciences Division

Weapons Experiments Division Explosives Operations Overview

Energy Technology Data Exchange (ETDEWEB)

Laintz, Kenneth E. [Los Alamos National Laboratory

2012-06-19

Presentation covers WX Division programmatic operations with a focus on JOWOG-9 interests. A brief look at DARHT is followed by a high level overview of explosives research activities currently being conducted within in the experimental groups of WX-Division. Presentation covers more emphasis of activities and facilities at TA-9 as these efforts have been more traditionally aligned with ongoing collaborative explosive exchanges covered under JOWOG-9.

Laser and Plasma Technology Division annual report 1993

International Nuclear Information System (INIS)

Venkatramani, N.; Verma, R.L.

1994-01-01

This report describes the activities of the Laser and Plasma Technology Division during the year 1993. This Division is engaged in the research and development of high power beams namely laser, plasma and electron beams, which are characterized by high power density, normally in excess of 1 kW/mm 2 . Laser and Plasma Technology Division has strived to establish indigenous capability to cater to the requirements of the Department of Atomic Energy. The broad programme objectives of the Division are : (1) Development and technology readiness studies of laser, plasma and electron beam devices, (2) Studies on related physical phenomena with a view to gain better understanding of the devices, and (3) Improvements in technology and exploration of new areas. This report covers the activities of the Division during 1993 and describes how successfully the objectives have been met. The activities described in the report are diverse in nature. The report has been compiled from individual reports of various groups/sections with marginal editing. (author). refs., tabs., figs

Laser and Plasma Technology Division annual report 1993

Energy Technology Data Exchange (ETDEWEB)

Venkatramani, N; Verma, R L [eds.; Bhabha Atomic Research Centre, Bombay (India). Laser and Plasma Technology Div.

1994-12-31

This report describes the activities of the Laser and Plasma Technology Division during the year 1993. This Division is engaged in the research and development of high power beams namely laser, plasma and electron beams, which are characterized by high power density, normally in excess of 1 kW/mm{sup 2}. Laser and Plasma Technology Division has strived to establish indigenous capability to cater to the requirements of the Department of Atomic Energy. The broad programme objectives of the Division are : (1) Development and technology readiness studies of laser, plasma and electron beam devices, (2) Studies on related physical phenomena with a view to gain better understanding of the devices, and (3) Improvements in technology and exploration of new areas. This report covers the activities of the Division during 1993 and describes how successfully the objectives have been met. The activities described in the report are diverse in nature. The report has been compiled from individual reports of various groups/sections with marginal editing. (author). refs., tabs., figs.

DNR Division of Parks and Trails District Boundaries

Data.gov (United States)

Minnesota Department of Natural Resources — This data shows the DNR Division of Parks and Trails District Boundaries as of May 2010. The boundaries were created by the Division Leadership Team. Boundaries are...

Energy Technology Division research summary -- 1994

International Nuclear Information System (INIS)

1994-09-01

Research funded primarily by the NRC is directed toward assessing the roles of cyclic fatigue, intergranular stress corrosion cracking, and irradiation-assisted stress corrosion cracking on failures in light water reactor (LWR) piping systems, pressure vessels, and various core components. In support of the fast reactor program, the Division has responsibility for fuel-performance modeling and irradiation testing. The Division has major responsibilities in several design areas of the proposed International Thermonuclear Experimental Reactor (ITER). The Division supports the DOE in ensuring safe shipment of nuclear materials by providing extensive review of the Safety Analysis Reports for Packaging (SARPs). Finally, in the nuclear area they are investigating the safe disposal of spent fuel and waste. In work funded by DOE's Energy Efficiency and Renewable Energy, the high-temperature superconductivity program continues to be a major focal point for industrial interactions. Coatings and lubricants developed in the division's Tribology Section are intended for use in transportation systems of the future. Continuous fiber ceramic composites are being developed for high-performance heat engines. Nondestructive testing techniques are being developed to evaluate fiber distribution and to detect flaws. A wide variety of coatings for corrosion protection of metal alloys are being studied. These can increase lifetimes significant in a wide variety of coal combustion and gasification environments

Solid State Division

International Nuclear Information System (INIS)

Green, P.H.; Watson, D.M.

1989-08-01

This report contains brief discussions on work done in the Solid State Division of Oak Ridge National Laboratory. The topics covered are: Theoretical Solid State Physics; Neutron scattering; Physical properties of materials; The synthesis and characterization of materials; Ion beam and laser processing; and Structure of solids and surfaces

Marriage, Specialization, and the Gender Division of Labor

OpenAIRE

Matthew J. Baker; Joyce P. Jacobsen

2005-01-01

A customary gender division of labor is one in which women and men are directed towards certain tasks and/or explicitly prohibited from performing others. We offer an explanation as to why the gender division of labor is so often enforced by custom, and why customary gender divisions of labor generally involve both direction and prohibition. Our model builds on the literature on the marital hold-up problem, and considers both problems in choice of specialty and human capital acquisition in a ...

Fuel Chemistry Division: progress report for 1985

International Nuclear Information System (INIS)

1988-01-01

Fuel Chemistry Division was formed in May 1985 to give a larger emphasis on the research and development in chemistry of the nuclear fuel cycle. The areas of research in Fuel Chemistry Division are fuel development and its chemical quality control, understanding of the fuel behaviour and post irradiation examinations, chemistry of reprocessing and waste management processes as also the basic aspects of actinide and relevant fission product elements. This report summarises the work by the staff of the Division during 1985 and also some work from the previous periods which was not reported in the progress reports of the Radiochemistry Division. The work related to the FBTR fuel was one of the highlights during this period. In the area of process chemistry useful work has been carried out for processing of plutonium bearing solutions. In the area of mass spectrometry, the determination of trace constituents by spark source mass spectrometry has been a major area of research. Significant progress has also been made in the use of alpha spectromet ry techniques for the determination of plutonium in dissolver solution and other samples. The technology of plutonium utilisation is quite complex and the Division would continue to look into the chemical aspects of this technology and provide the necessary base for future developments in this area. (author)

75 FR 45154 - National Security Division; Agency Information Collection Activities:

Science.gov (United States)

2010-08-02

... DEPARTMENT OF JUSTICE [OMB Number 1124-0003] National Security Division; Agency Information...), National Security Division (NSD), will be submitting the following information collection request to the..., 10th & Constitution Avenue, NW., National Security Division, Counterespionage Section/Registration Unit...

The RAppArmor Package: Enforcing Security Policies in R Using Dynamic Sandboxing on Linux

Directory of Open Access Journals (Sweden)

Jeroen Ooms

2013-11-01

Full Text Available The increasing availability of cloud computing and scientific super computers brings great potential for making R accessible through public or shared resources. This allows us to efficiently run code requiring lots of cycles and memory, or embed R functionality into, e.g., systems and web services. However some important security concerns need to be addressed before this can be put in production. The prime use case in the design of R has always been a single statistician running R on the local machine through the interactive console. Therefore the execution environment of R is entirely unrestricted, which could result in malicious behavior or excessive use of hardware resources in a shared environment. Properly securing an R process turns out to be a complex problem. We describe various approaches and illustrate potential issues using some of our personal experiences in hosting public web services. Finally we introduce the RAppArmor package: a Linux based reference implementation for dynamic sandboxing in R on the level of the operating system.

2003 Chemical Engineering Division annual technical report

International Nuclear Information System (INIS)

Lewis, D.; Graziano, D.; Miller, J. F.; Vandegrift, G.

2004-01-01

The Chemical Engineering Division is one of six divisions within the Engineering Research Directorate at Argonne National Laboratory, one of the U.S. government's oldest and largest research laboratories. The University of Chicago oversees the laboratory on behalf of the U.S. Department of Energy (DOE). Argonne's mission is to conduct basic scientific research, to operate national scientific facilities, to enhance the nation's energy resources, to promote national security, and to develop better ways to manage environmental problems. Argonne has the further responsibility of strengthening the nation's technology base by developing innovative technology and transferring it to industry. The Division is a diverse early-stage engineering organization, specializing in the treatment of spent nuclear fuel, development of advanced electrochemical power sources, and management of both high- and low-level nuclear wastes. Additionally, the Division operates the Analytical Chemistry Laboratory, which provides a broad range of analytical services to Argonne and other organizations. The Division is multidisciplinary. Its people have formal training in chemistry; physics; materials science; and electrical, mechanical, chemical, and nuclear engineering. They are specialists in electrochemistry, ceramics, metallurgy, catalysis, materials characterization, nuclear magnetic resonance, repository science, and the nuclear fuel cycle. Our staff have experience working in and collaborating with university, industry and government research and development laboratories throughout the world. Our wide-ranging expertise finds ready application in solving energy, national security, and environmental problems. Division personnel are frequently called on by governmental and industrial organizations for advice and contributions to problem solving in areas that intersect present and past Division programs and activities. Currently, we are engaged in the development of several technologies of

The Effects of Posture, Body Armor and Other Equipment on Rifleman Lethality

National Research Council Canada - National Science Library

Kramlich, Gary R., II

2005-01-01

...? This study quantifies the effects of Soldier equipment on lethality through multi-factor logistic regression using data from range experiments with the 1st Brigade, 1st Infantry Division (Mechanized...

Nuclear Physics Division annual report 1992

International Nuclear Information System (INIS)

Betigeri, M.G.

1993-01-01

The report covers the research and development activities of the Nuclear Physics Division for the period January to December 1992. These research and development activities are reported under the headings: 1) Experiments, 2) Theory, 3) Applications, 4) Instrumentation, and 5) The Pelletron Accelerator. At the end a list of publications by the staff scientists of the Division is given. Colloquia and seminars held during the year are also listed. (author). refs., tabs., figs

The Time Division Multi-Channel Communication Model and the Correlative Protocol Based on Quantum Time Division Multi-Channel Communication

International Nuclear Information System (INIS)

Liu Xiao-Hui; Pei Chang-Xing; Nie Min

2010-01-01

Based on the classical time division multi-channel communication theory, we present a scheme of quantum time-division multi-channel communication (QTDMC). Moreover, the model of quantum time division switch (QTDS) and correlative protocol of QTDMC are proposed. The quantum bit error rate (QBER) is analyzed and the QBER simulation test is performed. The scheme shows that the QTDS can carry out multi-user communication through quantum channel, the QBER can also reach the reliability requirement of communication, and the protocol of QTDMC has high practicability and transplantable. The scheme of QTDS may play an important role in the establishment of quantum communication in a large scale in the future. (general)

Reactor Engineering Division annual report

International Nuclear Information System (INIS)

Hirota, Jitsuya; Asaoka, Takumi; Suzuki, Tomoo; Mitani, Hiroshi; Akino, Fujiyoshi

1977-09-01

Research activities in the Division of Reactor Engineering in fiscal 1976 are described. Works of the division concern mainly the development of multi-purpose Very High Temperature Gas Cooled Reactor, fusion reactor engineering, and the development of Liquid Metal Fast Breeder Reactor in Power Reactor and Nuclear Fuel Development Corporation. Contents of the report are nuclear data and group constants, theoretical method and code development, integral experiment and analysis, shielding, heat transfer and fluid dynamics, reactor and nuclear instrumentation, dynamics analysis and control method development, fusion reactor technology, and activities of the Committee on Reactor Physics. (auth.)

Reactor Engineering Division annual report

International Nuclear Information System (INIS)

1976-09-01

Research activities conducted in Reactor Engineering Division in fiscal 1975 are summarized in this report. Works in the division are closely related to the development of multi-purpose High-temperature Gas Cooled Reactor, the development of Liquid Metal Fast Breeder Reactor by Power Reactor and Nuclear Fuel Development Corporation, and engineering research of thermonuclear fusion reactor. Many achievements are described concerning nuclear data and group constants, theoretical method and code development, integral experiment and analysis, shielding, heat transfer and fluid dynamics, reactor and nuclear instrumentation, dynamics analysis and control method development, fusion reactor technology and activities of the Committee on Reactor Physics. (auth.)

Reactor Engineering Division annual report

International Nuclear Information System (INIS)

1975-11-01

Research activities in fiscal 1974 in Reactor Engineering Division of eight laboratories and computing center are described. Works in the division are closely related with the development of a multi-purpose High-temperature Gas Cooled Reactor, the development of a Liquid Metal Fast Breeder Reactor in Power Reactor and Nuclear Fuel Development Corporation, and engineering of thermonuclear fusion reactors. They cover nuclear data and group constants, theoretical method and code development, integral experiment and analysis, shielding, heat transfer and fluid dynamics, reactor and nuclear instrumentation, dynamics analysis and control method development, fusion reactor technology and aspects of the computing center. (auth.)

Reactor Engineering Division annual report

International Nuclear Information System (INIS)

Matsuura, Shojiro; Nakahara, Yasuaki; Takano, Hideki

1982-09-01

Research and development activities in the Division of Reactor Engineering in fiscal 1981 are described. The work of the Division is closely related to development of multipurpose Very High Temperature Gas Cooled Reactor and fusion reactor, and development of Liquid Metal Fast Breeder Reactor carried out by Power Reactor and Nuclear Fuel Development Corporation. Contents of the report are achievements in fields such as nuclear data and group constants, theoretical method and code development, integral experiment and analysis, shielding, reactor and nuclear instrumentation, reactor control and diagnosis, and fusion reactor technology, and activities of the Committee on Reactor Physics. (author)

Determination of cell division axes in the early embryogenesis of Caenorhabditis elegans

OpenAIRE

1987-01-01

The establishment of cell division axes was examined in the early embryonic divisions of Caenorhabditis elegans. It has been shown previously that there are two different patterns of cleavage during early embryogenesis. In one set of cells, which undergo predominantly determinative divisions, the division axes are established successively in the same orientation, while division axes in the other set, which divide mainly proliferatively, have an orthogonal pattern of division. We have investig...

History of Division 29, 1993-2013: another 20 years of psychotherapy.

Science.gov (United States)

Williams, Elizabeth Nutt; Barnett, Jeffrey E; Canter, Mathilda B

2013-03-01

The history of Division 29 (Psychotherapy) of the American Psychological Association (APA) from 1993 to 2013 is reviewed. The 20 years of history can be traced via the Division's primary publications (the journal Psychotherapy and its newsletter Psychotherapy Bulletin) as well as the history of those who have served leadership roles in the Division and have won Divisional awards. Several recurring themes emerge related to the Division's articulations of its own identity, the Division's advocacy efforts vis-à-vis the profession and the APA, and the work of the Division on behalf of major social issues (such as disaster relief and the nation's health care).

Solid State Division

Energy Technology Data Exchange (ETDEWEB)

Green, P.H.; Watson, D.M. (eds.)

1989-08-01

This report contains brief discussions on work done in the Solid State Division of Oak Ridge National Laboratory. The topics covered are: Theoretical Solid State Physics; Neutron scattering; Physical properties of materials; The synthesis and characterization of materials; Ion beam and laser processing; and Structure of solids and surfaces. (LSP)

A connection between free and classical infinite divisibility

DEFF Research Database (Denmark)

Barndorff-Nielsen, Ole Eiler; Thorbjørnsen, Steen

2004-01-01

In this paper we continue our studies, initiated in Refs. 2–4, of the connections between the classes of infinitely divisible probability measures in classical and in free probability. We show that the free cumulant transform of any freely infinitely divisible probability measure equals...... the classical cumulant transform of a certain classically infinitely divisible probability measure, and we give several characterizations of the latter measure, including an interpretation in terms of stochastic integration. We find, furthermore, an alternative definition of the Bercovici–Pata bijection, which...

Onset of cell division in maize germination: action of auxins

International Nuclear Information System (INIS)

de Jimenez, E.S.; Baiza, A.; Aguilar, R.

1987-01-01

Seed germination implies metabolic reactivation, synthesis of macromolecules and onset of cell division. During maize germination, meristematic tissues of embryos re-initiate cell division asynchronically. Since auxins are known to stimulate cell division, they asked how auxins might regulate cell cycle re-initiation. Embryonic tissues were incubated with and without auxins. A pulse of either 3 H-thymidine or 32 P-ortophosphate was given to the tissues. Mitotic indexes were determined and % of labeled mitotic cells recorded. Results indicated that meristematic cells re-initiate cell division either from G 1 or G 2 phases. Auxin stimulated differentially the cell division process of these cells. 32 P incorporation into cytoplasmic or nucleic histones was measured. Auxins stimulated this incorporation. Active turnover of histone phosphorylation occurred simultaneously to the cell division process. It is suggested that auxins might regulate the cell cycle by phosphorylation-dephosphorylation of histones

Organization structure. Main activities of the Division

International Nuclear Information System (INIS)

2008-01-01

In this chapter the organization structure as well as main activities of the Division for radiation safety, NPP decommissioning and radioactive waste management are presented. This Division of the VUJE, a.s. consists of the following sections and departments: Section for economic and technical services; Section for radiation protection of employees; Department for management of emergency situations and risk assessment; Department for implementation of nuclear power facilities decommissioning and RAW management; Department for personnel and environmental dosimetry; Department for preparation of NPP decommissioning; Department for RAW treatment technologies; Department for chemical regimes and physico-chemical analyses; Department for management of nuclear power facilities decommissioning and RAW management. Main activities of this Division are presented.

ADP Analysis project for the Human Resources Management Division

Science.gov (United States)

Tureman, Robert L., Jr.

1993-01-01

The ADP (Automated Data Processing) Analysis Project was conducted for the Human Resources Management Division (HRMD) of NASA's Langley Research Center. The three major areas of work in the project were computer support, automated inventory analysis, and an ADP study for the Division. The goal of the computer support work was to determine automation needs of Division personnel and help them solve computing problems. The goal of automated inventory analysis was to find a way to analyze installed software and usage on a Macintosh. Finally, the ADP functional systems study for the Division was designed to assess future HRMD needs concerning ADP organization and activities.

High Thermal Dissipation of Al Heat Sink When Inserting Ceramic Powders by Ultrasonic Mechanical Coating and Armoring.

Science.gov (United States)

Tsai, Wei-Yu; Huang, Guan-Rong; Wang, Kuang-Kuo; Chen, Chin-Fu; Huang, J C

2017-04-26

Aluminum alloys, which serve as heat sink in light-emitting diode (LED) lighting, are often inherent with a high thermal conductivity, but poor thermal total emissivity. Thus, high emissive coatings on the Al substrate can enhance the thermal dissipation efficiency of radiation. In this study, the ultrasonic mechanical coating and armoring (UMCA) technique was used to insert various ceramic combinations, such as Al₂O₃, SiO₂, or graphite, to enhance thermal dissipation. Analytic models have been established to couple the thermal radiation and convection on the sample surface through heat flow equations. A promising match has been reached between the theoretical predictions and experimental measurements. With the adequate insertion of ceramic powders, the temperature of the Al heat sinks can be lowered by 5-11 °C, which is highly favorable for applications requiring cooling components.

Engineering Research Division publication report, calendar year 1980

International Nuclear Information System (INIS)

Miller, E.K.; Livingston, P.L.; Rae, D.C.

1980-06-01

Each year the Engineering Research Division of the Electronics Engineering Department at Lawrence Livermore Laboratory has issued an internal report listing all formal publications produced by the Division during the calendar year. Abstracts of 1980 reports are presented

Earth Sciences Division collected abstracts: 1980

Energy Technology Data Exchange (ETDEWEB)

Henry, A.L.; Hornady, B.F. (eds.)

1981-10-15

This report is a compilation of abstracts of papers, reports, and talks presented during 1980 at national and international meetings by members of the Earth Sciences Division, Lawrence Livermore National Laboratory. The arrangement is alphabetical (by author). For a given report, a bibliographic reference appears under the name of each coauthor, but the abstract itself is given only under the name of the first author (indicated in capital letters) or the first Earth Sciences Division author.

Nuclear Science Division: 1993 Annual report

International Nuclear Information System (INIS)

Myers, W.D.

1994-06-01

This report describes the activities of the Nuclear Science Division for the 1993 calendar year. This was another significant year in the history of the Division with many interesting and important accomplishments. Activities for the following programs are covered here: (1) nuclear structure and reactions program; (2) the Institute for Nuclear and Particle Astrophysics; (3) relativistic nuclear collisions program; (4) nuclear theory program; (5) nuclear data evaluation program, isotope project; and (6) 88-inch cyclotron operations

Nuclear Science Division: 1993 Annual report

Energy Technology Data Exchange (ETDEWEB)

Myers, W.D. [ed.

1994-06-01

This report describes the activities of the Nuclear Science Division for the 1993 calendar year. This was another significant year in the history of the Division with many interesting and important accomplishments. Activities for the following programs are covered here: (1) nuclear structure and reactions program; (2) the Institute for Nuclear and Particle Astrophysics; (3) relativistic nuclear collisions program; (4) nuclear theory program; (5) nuclear data evaluation program, isotope project; and (6) 88-inch cyclotron operations.

Earth Sciences Division annual report 1989

Energy Technology Data Exchange (ETDEWEB)

1990-06-01

This Annual Report presents summaries of selected representative research activities from Lawrence Berkeley Laboratory grouped according to the principal disciplines of the Earth Sciences Division: Reservoir Engineering and Hydrology, Geology and Geochemistry, and Geophysics and Geomechanics. We are proud to be able to bring you this report, which we hope will convey not only a description of the Division's scientific activities but also a sense of the enthusiasm and excitement present today in the Earth Sciences.

Earth Sciences Division collected abstracts: 1980

International Nuclear Information System (INIS)

Henry, A.L.; Hornady, B.F.

1981-01-01

This report is a compilation of abstracts of papers, reports, and talks presented during 1980 at national and international meetings by members of the Earth Sciences Division, Lawrence Livermore National Laboratory. The arrangement is alphabetical (by author). For a given report, a bibliographic reference appears under the name of each coauthor, but the abstract itself is given only under the name of the first author (indicated in capital letters) or the first Earth Sciences Division author

Radiochemistry Division annual progress report: 1988

International Nuclear Information System (INIS)

1990-01-01

The report covers the research and development (R and D) work carried out by Radiochemistry Division, Bhabha Atomic Research Centre, Bombay during the period 1987-1988. The R and D work is reported in the form of individual summari es grouped under the headings: (1)Actinide Chemistry, (2)Nuclear Chemistry, and (3)Spectroscopy. Some of the highlights of the work are studies on : (a)solvent extraction and complexation behaviour of actinides, (b)helium ion induced fission of 238 U and 165 Ho and fission yield of 252 Cf(sf), (c)separation of rare earths from fission products, (d)positron annihilation spectroscopy of high Tc superconductors, and (e)EPR spectroscopy of high Tc superconductors. Radioanalytical services and radiation sources given to the other Divisions and Organisations are listed. A list of publications and symposia papers by scientists of the Division is also given. 45 figs., 49 tabs

Cell-Division Behavior in a Heterogeneous Swarm Environment.

Science.gov (United States)

Erskine, Adam; Herrmann, J Michael

2015-01-01

We present a system of virtual particles that interact using simple kinetic rules. It is known that heterogeneous mixtures of particles can produce particularly interesting behaviors. Here we present a two-species three-dimensional swarm in which a behavior emerges that resembles cell division. We show that the dividing behavior exists across a narrow but finite band of parameters and for a wide range of population sizes. When executed in a two-dimensional environment the swarm's characteristics and dynamism manifest differently. In further experiments we show that repeated divisions can occur if the system is extended by a biased equilibrium process to control the split of populations. We propose that this repeated division behavior provides a simple model for cell-division mechanisms and is of interest for the formation of morphological structure and to swarm robotics.

Applied Chemistry Division progress report for the period 1990-1992

International Nuclear Information System (INIS)

Bharadwaj, S.R.; Kishore, K.; Ramshesh, V.

1993-01-01

The report covers the research and development (R and D) activities of the Applied Chemistry Division for the period January 1990 to December, 1992. R and D programmes of the Division are formulated to study the chemical aspects related to nuclear power plants and heavy water plants. The Division also gives consultancy to DAE units and outside agencies on water chemistry problems. The thrust areas of the Division's R and D programmes are : decontamination of nuclear facilities, metal water interaction of the materials used in PHT system, chemistry of soluble poisons, biofouling and its control in cooling water circuits, and treatment of cooling waters. Other major R and D activities are in the areas of: solid state reactions and high temperature thermodynamics, primary coolant water chemistry, speciation studies in metal amine systems, high temperature aqueous radiation chemistry. The Division was engaged in studies in novel areas such as dental implants, remote sealing of pipes in MS pipes, and cold fusion. The Division also designed and fabricated instruments like the Knudsen cell mass spectrometer, calorimeters and developed required software. All these R and D activities are reported in the form of individual summaries. A list of publications from the Division and a list of the staff members of the Division are given at the end of the report. (author). tabs., figs., appendices

Towers of generalized divisible quantum codes

Science.gov (United States)

Haah, Jeongwan

2018-04-01

A divisible binary classical code is one in which every code word has weight divisible by a fixed integer. If the divisor is 2ν for a positive integer ν , then one can construct a Calderbank-Shor-Steane (CSS) code, where X -stabilizer space is the divisible classical code, that admits a transversal gate in the ν th level of Clifford hierarchy. We consider a generalization of the divisibility by allowing a coefficient vector of odd integers with which every code word has zero dot product modulo the divisor. In this generalized sense, we construct a CSS code with divisor 2ν +1 and code distance d from any CSS code of code distance d and divisor 2ν where the transversal X is a nontrivial logical operator. The encoding rate of the new code is approximately d times smaller than that of the old code. In particular, for large d and ν ≥2 , our construction yields a CSS code of parameters [[O (dν -1) ,Ω (d ) ,d ] ] admitting a transversal gate at the ν th level of Clifford hierarchy. For our construction we introduce a conversion from magic state distillation protocols based on Clifford measurements to those based on codes with transversal T gates. Our tower contains, as a subclass, generalized triply even CSS codes that have appeared in so-called gauge fixing or code switching methods.

Earth Sciences Division annual report 1990

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-06-01

This Annual Report presents summaries of selected representative research activities grouped according to the principal disciplines of the Earth Sciences Division: Reservoir Engineering and Hydrogeology, Geology and Geochemistry, and Geophysics and Geomechanics. Much of the Division`s research deals with the physical and chemical properties and processes in the earth`s crust, from the partially saturated, low-temperature near-surface environment to the high-temperature environments characteristic of regions where magmatic-hydrothermal processes are active. Strengths in laboratory and field instrumentation, numerical modeling, and in situ measurement allow study of the transport of mass and heat through geologic media -- studies that now include the appropriate chemical reactions and the hydraulic-mechanical complexities of fractured rock systems. Of particular note are three major Division efforts addressing problems in the discovery and recovery of petroleum, the application of isotope geochemistry to the study of geodynamic processes and earth history, and the development of borehole methods for high-resolution imaging of the subsurface using seismic and electromagnetic waves. In 1989 a major DOE-wide effort was launched in the areas of Environmental Restoration and Waste Management. Many of the methods previously developed for and applied to deeper regions of the earth will in the coming years be turned toward process definition and characterization of the very shallow subsurface, where man-induced contaminants now intrude and where remedial action is required.

Infrastructure Engineering and Deployment Division

Data.gov (United States)

Federal Laboratory Consortium — Volpe's Infrastructure Engineering and Deployment Division advances transportation innovation by being leaders in infrastructure technology, including vehicles and...

Peptidoglycan architecture can specify division planes in Staphylococcus aureus.

Science.gov (United States)

Turner, Robert D; Ratcliffe, Emma C; Wheeler, Richard; Golestanian, Ramin; Hobbs, Jamie K; Foster, Simon J

2010-06-15

Division in Staphylococci occurs equatorially and on specific sequentially orthogonal planes in three dimensions, resulting, after incomplete cell separation, in the 'bunch of grapes' cluster organization that defines the genus. The shape of Staphylococci is principally maintained by peptidoglycan. In this study, we use Atomic Force Microscopy (AFM) and fluorescence microscopy with vancomycin labelling to examine purified peptidoglycan architecture and its dynamics in Staphylococcus aureus and correlate these with the cell cycle. At the presumptive septum, cells were found to form a large belt of peptidoglycan in the division plane before the centripetal formation of the septal disc; this often had a 'piecrust' texture. After division, the structures remain as orthogonal ribs, encoding the location of past division planes in the cell wall. We propose that this epigenetic information is used to enable S. aureus to divide in sequentially orthogonal planes, explaining how a spherical organism can maintain division plane localization with fidelity over many generations.

Reactor Engineering Division annual report

International Nuclear Information System (INIS)

1980-09-01

Research activities in the Division of Reactor Engineering in fiscal 1979 are described. The work of the Division is closely related to development of multi-purpose Very High Temperature Gas Cooled Reactor and fusion reactor, and development of Liquid Metal Fast Breeder Reactor carried out by Power Reactor and Nuclear Fuel Development Corporation. Contents of the report are achievements in fields such as nuclear data and group constants, theoretical method and code development, integral experiment and analysis, shielding, reactor and nuclear instrumentation, reactor control and diagnosis, and fusion reactor technology, and activities of the Committees on Reactor Physics and on Decomissioning of Nuclear Facilities. (author)

Radiochemistry Division annual progress report : 1991

International Nuclear Information System (INIS)

Natarajan, V.; Godbole, S.V.; Iyer, R.H.

1993-01-01

The research and development activities of the Radiochemistry Division during 1991 are briefly described under the headings: (i) Nuclear chemistry, (ii) Actinide chemistry, and (iii) Spectroscopy. In the field of nuclear chemistry, the main emphasis has been on the studies of fission process induced by reactor neutrons and light and heavy ions on actinides and low Z (Z c superconductors. A list of publications by the scientific staff of the Division is given at the end. (author). 31 figs., 49 tabs

Nuclear Power Division

International Nuclear Information System (INIS)

Anon.

1981-01-01

The 1981-85 research program planned by the Nuclear Power Division of EPRI places major emphasis on the assurance of safety and realiability of light water reactors (LWRs). Of high priority is a better knowledge of LWR-system behavior undeer abnormal conditions and the behavior of structural materials used for pressure vessels, piping, and large nuclear-plant components. Strong emphasis is also placed on achieving the most-effective performance and utilization of nuclear fuels and improving the corrosion resistance of pressurized-water-reactor steam generators. Efforts are underway to reduce radiation exposure and outage duration and to investigate the human factors involved in plant operation and maintenance. Substantial emphasis is placed on short-range goals designed to achieve useful results in the next two to seven years. The Division's mid- and long-range goal is to improve the use of fissionable and fertile materials and aid in the realization of other reactor systems. A series of general goals, categorized into three time frames and planned expenditures shows the trend of work to be undertaken. 53 figures

Contacts in the Office of Pesticide Programs, Registration Division

Science.gov (United States)

The Registration Division (RD) is responsible product registrations, amendments, registrations, tolerances, experimental use permits, and emergency exemptions for conventional chemical pesticides. Find contacts in this division.

Adaptive pole placement: the division by zero problem

NARCIS (Netherlands)

Arent, Krzysztof; Arent, K.; Polderman, Jan W.; Mareels, I.M.Y.; Mareels, Iven

1995-01-01

We re-examine the division by zero problem which occurs in certainty equivalence based indirect adaptive control algorithms applied to linear systems. By exploiting a parametrization for linear systems induced by the continued fraction description of its transfer function, the division by zero

"American Gothic" and the Division of Labor.

Science.gov (United States)

Saunders, Robert J.

1987-01-01

Provides historical review of gender-based division of labor. Argues that gender-based division of labor served a purpose in survival of tribal communities but has lost meaning today and may be a handicap to full use of human talent and ability in the arts. There is nothing in various art forms which make them more appropriate for males or…

Security and Emergency Management Division

Data.gov (United States)

Federal Laboratory Consortium — Volpe's Security and Emergency Management Division identifies vulnerabilities, risks, and opportunities to improve the security of transportation systems, critical...

Systems Safety and Engineering Division

Data.gov (United States)

Federal Laboratory Consortium — Volpe's Systems Safety and Engineering Division conducts engineering, research, and analysis to improve transportation safety, capacity, and resiliency. We provide...

Situational Awareness and Logistics Division

Data.gov (United States)

Federal Laboratory Consortium — Volpe's Situational Awareness and Logistics Division researches, develops, implements, and analyzes advanced systems to protect, enhance, and ensure resilienceof the...

Evolutionary dynamics of division of labor games with selfish agents

Science.gov (United States)

Zhang, Jianlei; Li, Qiaoyu; Zhang, Chunyan

2017-11-01

The division of labor is one of the most basic and widely studied aspects of collective behavior in natural systems. Studies of division of labor are concerned with the integration of the individual worker behavior into a colony level task organization and with the question of how the regulation of the division of labor may contribute to the colony efficiency. This paper investigates the evolution of the division of labor with three strategies by employing the evolutionary game theory. Thus, these available strategies are, respectively, strategy A (performing task A), strategy B (performing task B), and strategy D (not performing any task but only free riding others' contributions). And, two typical networks (i.e., BA scale-free network and lattice network) are employed here for describing the interaction structure among agents. The theoretical analysis together with simulation results reveal that the division of labor can evolve and leads to players that differ in their tendency to take on a given task. The conditions under which the division of labor evolves depend on the costs for performing the task, the benefits led by performing the task, and the interaction structures among the players who are involved with division of labor games.

Life Sciences Division annual report, 1988

Energy Technology Data Exchange (ETDEWEB)

Marrone, B.L.; Cram, L.S. (comps.)

1989-04-01

This report summarizes the research and development activities of Los Alamos National Laboratory's Life Sciences Division for the calendar year 1988. Technical reports related to the current status of projects are presented in sufficient detail to permit the informed reader to assess their scope and significance. Summaries useful to the casual reader desiring general information have been prepared by the Group Leaders and appear in each group overview. Investigators on the staff of the Life Sciences Division will be pleased to provide further information.

Nuclear Physics Division: annual report 1991

International Nuclear Information System (INIS)

Betigeri, M.G.

1993-01-01

A brief account of the research and development activities carried out by the Nuclear Physics Division, Bhabha Atomic Research Centre, Bombay during the period January 1991 to December 1991 is presented. These R and D activities are reported under the headings : 1) Accelerator Facilities, 2) Research Activities, and 3) Instrumentation. At the end, a list of publications by the staff scientists of the Division is given. The list includes papers published in journals, papers presented at conferences, symposia etc., and technical reports. (author). figs., tabs

Life Sciences Division annual report, 1988

International Nuclear Information System (INIS)

Marrone, B.L.; Cram, L.S.

1989-04-01

This report summarizes the research and development activities of Los Alamos National Laboratory's Life Sciences Division for the calendar year 1988. Technical reports related to the current status of projects are presented in sufficient detail to permit the informed reader to assess their scope and significance. Summaries useful to the casual reader desiring general information have been prepared by the Group Leaders and appear in each group overview. Investigators on the staff of the Life Sciences Division will be pleased to provide further information

Laser and Plasma Technology Division, Annual Reports 1996 and 1997

International Nuclear Information System (INIS)

Venkatramani, N.

1999-04-01

This report describes the activity of the Laser and Plasma Technology Division of Bhabha Atomic Research Centre during the two year period 1996- 1997. This division is engaged in the research and development of high power beams mainly laser, plasma and electron beams. Laser and Plasma Technology Division has strived to establish indigenous capability to cater to the requirements of Department of Atomic Energy. This involves development and technology readiness study of laser, plasma and electron beam devices. In addition, studies are also carried out on related physical phenomenon with a view to gain better understanding of the devices. This report has been compiled from individual reports of various groups/sections working in the division. A list of publications by the several members of the division is also included. (author)

HISTORY OF THE ENGINEERING PHYSICS AND MATHEMATICS DIVISION 1955-1993

Energy Technology Data Exchange (ETDEWEB)

Maskewitz, B.F.

2001-09-14

A review of division progress reports noting significant events and findings of the Applied Nuclear Physics, Neutron Physics, Engineering Physics, and then Engineering Physics and Mathematics divisions from 1955 to 1993 was prepared for use in developing a history of the Oak Ridge National Laboratory in celebration of its 50th year. The research resulted in an accumulation of historic material and photographs covering 38 years of effort, and the decision was made to publish a brief history of the division. The history begins with a detailed account of the founding of the Applied Nuclear Physics Division in 1955 and continues through the name change to the Neutron Physics Division in the late 1950s. The material thereafter is presented in decades--the sixties, seventies, and eighties--and ends as we enter the nineties.

A division algebra classification of generalized supersymmetries

International Nuclear Information System (INIS)

Toppan, Francesco

2004-10-01

Generalized supersymmetries admitting bosonic tensor central charges are classified in accordance with their division algebra properties. Division algebra consistent constraints lead (in the complex and quaternionic cases) to the classes of hermitian and holomorphic generalized supersymmetries. Applications to the analytic continuation of the M-algebra to the Euclidean and the systematic investigation of certain classes of models in generic space-times are briefly mentioned. (author)

78 FR 49111 - Airworthiness Directives; Pratt & Whitney Division Turbofan Engines

Science.gov (United States)

2013-08-13

... Airworthiness Directives; Pratt & Whitney Division Turbofan Engines AGENCY: Federal Aviation Administration (FAA... & Whitney Division (PW) turbofan engine model PW4074, PW4074D, PW4077, PW4077D, PW4084D, PW4090, and PW4090...) Applicability This AD applies to all Pratt & Whitney Division (PW) turbofan engine models PW4074, PW4074D...

Laser and Plasma Technology Division annual report 1995

International Nuclear Information System (INIS)

Venkatramani, N.

1996-01-01

This report describes the activity of the Laser and Plasma Technology Division of Bhabha Atomic Research Centre, Mumbai during the period 1995. This division is engaged in the research and development of high power beams namely lasers, plasma and electron beams which are characterized by high power density. This division has strived to establish indigenous capability to cater to the requirements of the Department of Atomic Energy. The broad program objectives of the division are (1) development and technology readiness studies of laser, plasma and electron beam devices; (2) studies on related physical phenomena with a view to gain better understanding of the devices and (3) improvements in technology and exploration of new areas. This report has been compiled from individual reports of various groups/sections with marginal editing. At the end of each section; a list of publications by the staff members in the field indicated by the title of the section is given. refs., figs., tabs

Engineering Physics and Mathematics Division progress report for period ending December 31, 1994

International Nuclear Information System (INIS)

Sincovec, R.F.

1995-07-01

This report provides a record of the research activities of the Engineering Physics and Mathematics Division for the period January 1, 1993, through December 31, 1994. This report is the final archival record of the EPM Division. On October 1, 1994, ORELA was transferred to Physics Division and on January 1, 1995, the Engineering Physics and Mathematics Division and the Computer Applications Division reorganized to form the Computer Science and Mathematics Division and the Computational Physics and Engineering Division. Earlier reports in this series are identified on the previous pages, along with the progress reports describing ORNL's research in the mathematical sciences prior to 1984 when those activities moved into the Engineering Physics and Mathematics Division

Engineering Physics and Mathematics Division progress report for period ending December 31, 1994

Energy Technology Data Exchange (ETDEWEB)

Sincovec, R.F.

1995-07-01

This report provides a record of the research activities of the Engineering Physics and Mathematics Division for the period January 1, 1993, through December 31, 1994. This report is the final archival record of the EPM Division. On October 1, 1994, ORELA was transferred to Physics Division and on January 1, 1995, the Engineering Physics and Mathematics Division and the Computer Applications Division reorganized to form the Computer Science and Mathematics Division and the Computational Physics and Engineering Division. Earlier reports in this series are identified on the previous pages, along with the progress reports describing ORNL`s research in the mathematical sciences prior to 1984 when those activities moved into the Engineering Physics and Mathematics Division.

AC/ARNG Integrated Division Concept Study, Appendices, Volume 3

National Research Council Canada - National Science Library

Twohig, John

1997-01-01

...) division headquarters. The US Army Training and Doctrine Command (TRADOC) was tasked to conduct a viability assessment of the AC/ARNG Integrated Division concept and focus on merits and implementation issues...

Cell Division and Evolution of Biological Tissues

Science.gov (United States)

Rivier, Nicolas; Arcenegui-Siemens, Xavier; Schliecker, Gudrun

A tissue is a geometrical, space-filling, random cellular network; it remains in this steady state while individual cells divide. Cell division (fragmentation) is a local, elementary topological transformation which establishes statistical equilibrium of the structure. Statistical equilibrium is characterized by observable relations (Lewis, Aboav) between cell shapes, sizes and those of their neighbours, obtained through maximum entropy and topological correlation extending to nearest neighbours only, i.e. maximal randomness. For a two-dimensional tissue (epithelium), the distribution of cell shapes and that of mother and daughter cells can be obtained from elementary geometrical and physical arguments, except for an exponential factor favouring division of larger cells, and exponential and combinatorial factors encouraging a most symmetric division. The resulting distributions are very narrow, and stationarity severely restricts the range of an adjustable structural parameter

Chemical Technology Division annual technical report, 1996

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-06-01

CMT is a diverse technical organization with principal emphases in environmental management and development of advanced energy sources. It conducts R&D in 3 general areas: development of advanced power sources for stationary and transportation applications and for consumer electronics, management of high-level and low-level nuclear wastes and hazardous wastes, and electrometallurgical treatment of spent nuclear fuel. The Division also performs basic research in catalytic chemistry involving molecular energy resources, mechanisms of ion transport in lithium battery electrolytes, materials chemistry of electrified interfaces and molecular sieves, and the theory of materials properties. It also operates the Analytical Chemistry Laboratory, which conducts research in analytical chemistry and provides analytical services for programs at ANL and other organizations. Technical highlights of the Division`s activities during 1996 are presented.

Division of labour and the evolution of extreme specialization.

Science.gov (United States)

Cooper, Guy A; West, Stuart A

2018-05-28

Division of labour is a common feature of social groups, from biofilms to complex animal societies. However, we lack a theoretical framework that can explain why division of labour has evolved on certain branches of the tree of life but not others. Here, we model the division of labour over a cooperative behaviour, considering both when it should evolve and the extent to which the different types should become specialized. We found that: (1) division of labour is usually-but not always-favoured by high efficiency benefits to specialization and low within-group conflict; and (2) natural selection favours extreme specialization, where some individuals are completely dependent on the helping behaviour of others. We make a number of predictions, several of which are supported by the existing empirical data, from microbes and animals, while others suggest novel directions for empirical work. More generally, we show how division of labour can lead to mutual dependence between different individuals and hence drive major evolutionary transitions, such as those to multicellularity and eusociality.

A novel cell division factor from tobacco 2B-13 cells that induced cell division in auxin-starved tobacco BY-2 cells

Science.gov (United States)

Shimizu, Takashi; Eguchi, Kentaro; Nishida, Ikuo; Laukens, Kris; Witters, Erwin; van Onckelen, Harry; Nagata, Toshiyuki

2006-06-01

Effects of auxin as plant hormones are widespread; in fact in almost all aspects of plant growth and development auxin plays a pivotal role. Although auxin is required for propagating cell division in plant cells, its effect upon cell division is least understood. If auxin is depleted from the culture medium, cultured cells cease to divide. It has been demonstrated in this context that the addition of auxin to auxin-starved nondividing tobacco BY-2 cells induced semisynchronous cell division. On the other hand, there are some cell lines, named habituated cells, that can grow without auxin. The cause and reason for the habituated cells have not been clarified. A habituated cell line named 2B-13 is derived from the tobacco BY-2 cell line, which has been most intensively studied among plant cell lines. When we tried to find the difference between two cell lines of BY-2 and 2B-13 cells, we found that the addition of culture filtrated from the auxin-habituated 2B-13 cells induced semisynchronous cell division in auxin-starved BY-2 cells. The cell division factor (CDF) that is responsible for inducing cell division in auxin-starved BY-2 cells was purified to near-homogeneity by sequential passage through a hydroxyapatite column, a ConA Sepharose column and a Sephadex gel filtration column. The resulting purified fraction appeared as a single band of high molecular weight on sodium dodecyl sulfate-polyacrylamide gel electrophoresis gels by silver staining and was able to induce cell division in auxin-starved BY-2 cells. Identification of the protein by MALD-TOF-MS/MS revealed that it is structurally related to P-glycoprotein from Gossypioides kirkii, which belongs to ATP-binding cassette (ABC)-transporters. The significance of CDF as a possible ABC-transporter is discussed in relationship to auxin-autotrophic growth and auxin-signaling pathway.

Theoretical Division progress report. [October 1976-January 1979

Energy Technology Data Exchange (ETDEWEB)

Cooper, N.G. (comp.)

1979-04-01

This report presents highlights of activities in the Theoretical (T) Division from October 1976-January 1979. The report is divided into three parts. Part I presents an overview of the Division: its unique function at the Los Alamos Scientific Laboratory (LASL) and within the scientific community as a whole; the organization of personnel; the main areas of research; and a survey of recent T-Division initiatives. This overview is followed by a survey of the 13 groups within the Division, their main responsibilities, interests, and expertise, consulting activities, and recent scientific accomplisments. The remainder of the report, Parts II and III, is devoted to articles on selected research activities. Recent efforts on topics of immediate interest to energy and weapons programs at LASL and elsewhere are described in Part II, Major National Programs. Separate articles present T-Divison contributions to weapons research, reactor safety and reactor physics research, fusion research, laser isotope separation, and other energy research. Each article is a compilation of independent projects within T Division, all related to but addressing different aspects of the major program. Part III is organized by subject discipline, and describes recent scientific advances of fundamental interest. An introduction, defining the scope and general nature of T-Division efforts within a given discipline, is followed by articles on the research topics selected. The reporting is done by the scientists involved in the research, and an attempt is made to communicate to a general audience. Some data are given incidentally; more technical presentations of the research accomplished may be found among the 47 pages of references. 110 figures, 5 tables.

Theoretical Physics Division

International Nuclear Information System (INIS)

This report is a survey of the studies done in the Theoretical Physics Division of the Nuclear Physics Institute; the subjects studied in theoretical nuclear physics were the few-nucleon problem, nuclear structure, nuclear reactions, weak interactions, intermediate energy and high energy physics. In this last field, the subjects studied were field theory, group theory, symmetry and strong interactions [fr

Long-term survivability of riprap for armoring uranium-mill tailings and covers: a literature review

International Nuclear Information System (INIS)

Lindsey, C.G.; Long, L.W.; Begej, C.W.

1982-06-01

Pacific Northwest Laboratory (PNL) is investigating the use of a rock armoring blanket (riprap) to mitigate wind and water erosion of an earthen radon suppression cover applied to uranium mill tailings. Because the radon suppression cover and the tailings must remain intact for up to 1000 years or longer, the riprap must withstand natural weathering forces. This report is a review of information on rock weathering and riprap durability. Chemical and physical weathering processes, rock characteristics related to durability, climatic conditions affecting the degree and rate of weathering, and testing procedures used to measure weathering susceptibilities have been reviewed. Sampling and testing techniques, as well as analyses of physical and chemical weathering susceptibilities, are necessary to evaluate rock durability. Many potential riprap materials may not be able to survive 1000 years of weathering. Available techniques for durability testing cannot adequately predict rock durability for the 1000-year period because they do not consider the issue of time (i.e., how long must riprap remain stable). This report includes an Appendix, which discusses rock weathering, written by Dr. Richard Jahns of Stanford University

Materials division facilities and equipment

International Nuclear Information System (INIS)

Biest, O. v.d.

1984-01-01

The research activities of the Division at the Petten Establishment have the aims of characterising the properties of high temperature materials in industrial process environments and of understanding the structures involved in order to gain an insight into behavioural mechanisms. Metallic materials fall within the scope of the programme; the activities are, at present, almost entirely concerned with austenitic steels and nickel based alloys. Starting in 1984, advanced ceramic materials will be studied as well. The equipment available permits the study of mechanical properties in controlled gaseous environments, of the rates and mechanisms of corrosive reactions between materials and those environments, and of the surface and bulk structures by advanced physical techniques. Special preparation and treatment techniques are available. The Division has developed a Data Bank on high temperature alloys. It also operates an information Centre, the activities of which include the organisation of scientific meetings, the commissioning of ''state of the art'' studies on topics in the field of high temperature materials and their applications and the development of a inventory of current research activities in the field in Europe. This booklet is intended to present the facilities and services of the Division to the organizations which are interested in its programmes of work

Activity Report of Reactor Physics Division - 1997

International Nuclear Information System (INIS)

Singh, Om Pal

1998-01-01

The research and development activities of the Reactor Physics Division of the Indira Gandhi Centre for Atomic Research (IGCAR), Kalpakkam during 1997 are reported. The activities are arranged under the headings: nuclear data processing and validation, PFBR and KAMINI core physics, FBTR core physics, radioactivity and shielding and safety analysis. A list of publications of the Division and seminars delivered are included at the end of the report

Power Efficient Division and Square Root Unit

DEFF Research Database (Denmark)

Liu, Wei; Nannarelli, Alberto

2012-01-01

Although division and square root are not frequent operations, most processors implement them in hardware to not compromise the overall performance. Two classes of algorithms implement division or square root: digit-recurrence and multiplicative (e.g., Newton-Raphson) algorithms. Previous work....... The proposed unit is compared to similar solutions based on the digit-recurrence algorithm and it is compared to a unit based on the multiplicative Newton-Raphson algorithm....

The design of the poloidal divertor experiment tokamak wall armor and inner limiter system

International Nuclear Information System (INIS)

Kugel, H.W.; Ulrickson, M.

1982-01-01

The inner wall protective plates for the Poloidal Divertor Experiment Tokamak are designed to absorb 8 MW of neutral deuterium beam power at maximum power densities of 3 kW/cm 2 for pulse lengths of 0.5 s. Preliminary studies indicate that the design could survive several pulses of l-s duration. The design consists of a tile and mounting plate structure. The mounting plates are water cooled to allow short duty cycles and beam calorimetry. The temperature and flow of the coolant are measured to obtain the injected power. A thermocouple array on the tiles provides beam position and power density profiles. Several material combinations for the tiles were subjected to thermal tests using both electron and neutral beams, and titanium-carbidecoated graphite was selected as the tile material. The heat transfer coefficient of the tile backing plate structure was measured to determine the maximum pulse rate allowable. The design of the armor system allows the structure to be used as a neutral beam power diagnostic and as an inner plasma limiter. The electrical and cooling systems external to the vacuum vessel are discussed

Characterization of dermal plates from armored catfish Pterygoplichthys pardalis reveals sandwich-like nanocomposite structure.

Science.gov (United States)

Ebenstein, Donna; Calderon, Carlos; Troncoso, Omar P; Torres, Fernando G

2015-05-01

Dermal plates from armored catfish are bony structures that cover their body. In this paper we characterized structural, chemical, and nanomechanical properties of the dermal plates from the Amazonian fish Pterygoplichthys pardalis. Analysis of the morphology of the plates using scanning electron microscopy (SEM) revealed that the dermal plates have a sandwich-like structure composed of an inner porous matrix surrounded by two external dense layers. This is different from the plywood-like laminated structure of elasmoid fish scales but similar to the structure of osteoderms found in the dermal armour of some reptiles and mammals. Chemical analysis performed using Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC) and X-ray diffraction (XRD) results revealed similarities between the composition of P. pardalis plates and the elasmoid fish scales of Arapaima gigas. Reduced moduli of P. pardalis plates measured using nanoindentation were also consistent with reported values for A. gigas scales, but further revealed that the dermal plate is an anisotropic and heterogeneous material, similar to many other fish scales and osteoderms. It is postulated that the sandwich-like structure of the dermal plates provides a lightweight and tough protective layer. Copyright © 2015 Elsevier Ltd. All rights reserved.

Interactions between non-native armored suckermouth catfish (Loricariidae: Pterygoplichthys) and native Florida manatee (Trichechus manatus latirostris) in artesian springs

Science.gov (United States)

Nico, Leo G.; Loftus, William F.; Reid, James P.

2009-01-01

Non-native suckermouth armored catfishes (Loricariidae) of the genus Pterygoplichthys are now common throughout much of peninsular Florida. In this paper, we present preliminary observations on interactions between a Pterygoplichthys species, tentatively identified as P. disjunctivus (Weber, 1991), and endangered native Florida manatees, Trichechus manatus latirostris (Harlan, 1824), in artesian spring systems in Florida's St. Johns River drainage. The introduced catfish have become abundant in spring habitats, sites used by manatees as winter thermal refuges. In the spring runs, Pterygoplichthys regularly attaches to manatees and grazes the epibiota on their skin. On occasion, dozens of Pterygoplichthys congregate on individual manatees. Manatee responses varied widely; some did not react visibly to attached catfish whereas others appeared agitated and attempted to dislodge the fish. The costs and/or benefits of this interaction to manatees remain unclear.

Genes involved in cell division in mycoplasmas

Directory of Open Access Journals (Sweden)

Frank Alarcón

2007-01-01

Full Text Available Bacterial cell division has been studied mainly in model systems such as Escherichia coli and Bacillus subtilis, where it is described as a complex process with the participation of a group of proteins which assemble into a multiprotein complex called the septal ring. Mycoplasmas are cell wall-less bacteria presenting a reduced genome. Thus, it was important to compare their genomes to analyze putative genes involved in cell division processes. The division and cell wall (dcw cluster, which in E. coli and B. subtilis is composed of 16 and 17 genes, respectively, is represented by only three to four genes in mycoplasmas. Even the most conserved protein, FtsZ, is not present in all mycoplasma genomes analyzed so far. A model for the FtsZ protein from Mycoplasma hyopneumoniae and Mycoplasma synoviae has been constructed. The conserved residues, essential for GTP/GDP binding, are present in FtsZ from both species. A strong conservation of hydrophobic amino acid patterns is observed, and is probably necessary for the structural stability of the protein when active. M. synoviae FtsZ presents an extended amino acid sequence at the C-terminal portion of the protein, which may participate in interactions with other still unknown proteins crucial for the cell division process.

Progress report [of] Technical Physics Division

International Nuclear Information System (INIS)

Vijendran, P.; Deshpande, R.Y.

1975-01-01

Activities of the Technical Physics Division of the Bhabha Atomic Research Centre, Bombay, over the last few years are reported. This division is engaged in developing various technologies supporting the development of nuclear technology. The various fields in which development is actively being carried out are : (i) vacuum technology, (ii) mass spectrometry, (iii) crystal technology, (iv) cryogenics, and (v) magnet technology. For surface studies, the field emission microscope and the Auger electron spectrometer and other types of spectrometers have been devised and perfected. Electromagnets of requisite strength to be used in MHD programme and NMR instruments are being fabricated. Various crystals such as NaI(Tl), Ge, Fluorides, etc. required as windows and prisms in X and gamma-ray spectroscopy, have been grown. In the cryogenics field, expansion engines required for air liquefaction plants, vacuum insulated dewars, helium gas thermometers etc. have been constructed. In addition to the above, the Division provides consultancy and training to personnel from various institutions and laboratories. Equipment and systems perfected are transferred to commercial organizations for regular production. (A.K.)

The Astrophysics Science Division Annual Report 2008

Science.gov (United States)

Oegerle, William; Reddy, Francis; Tyler, Pat

2009-01-01

The Astrophysics Science Division (ASD) at Goddard Space Flight Center (GSFC) is one of the largest and most diverse astrophysical organizations in the world, with activities spanning a broad range of topics in theory, observation, and mission and technology development. Scientific research is carried out over the entire electromagnetic spectrum from gamma rays to radio wavelengths as well as particle physics and gravitational radiation. Members of ASD also provide the scientific operations for three orbiting astrophysics missions WMAP, RXTE, and Swift, as well as the Science Support Center for the Fermi Gamma-ray Space Telescope. A number of key technologies for future missions are also under development in the Division, including X-ray mirrors, and new detectors operating at gamma-ray, X-ray, ultraviolet, infrared, and radio wavelengths. This report includes the Division's activities during 2008.

Reactor Engineering Division annual report

International Nuclear Information System (INIS)

1975-02-01

This report summarizes main research achievements in the 48th fiscal year which were made by Reactor Engineering Division consisted of eight laboratories and Computing Center. The major research and development projects, with which the research programmes in the Division are associated, are development of High Temperature Gas Cooled Reactor for multi-purpose use, development of Liquid Metal Fast Breeder Reactor conducted by Power Reactor and Nuclear Fuel Development Corporation, and Engineering Research Programme for Thermonuclear Fusion Reactor. Many achievements are reported in various research items such as nuclear data and group constants, theoretical method and code development, integral experiment and analysis, shielding, heat transfer and fluid dynamics, reactor and nuclear instrumentation, dynamics analysis and control method development, fusion reactor technology and activities of Computing Center. (auth.)

Earth Sciences Division, collected abstracts-1977. [Research programs

Energy Technology Data Exchange (ETDEWEB)

Quitiquit, W.A.; Ledbetter, G.P.; Henry, A.L.

1978-05-24

This report is a compilation of abstracts of papers, internal reports, and talks presented during 1977 at national and international meetings by members of the Earth Sciences Division, Lawrence Livermore Laboratory. It is arranged alphabetically by author and includes a cross-reference by subject indicating the areas of research interest of the Earth Sciences Division.

Motivation Cards to Support Students’ Understanding on Fraction Division

Directory of Open Access Journals (Sweden)

Kamirsyah Wahyu

2017-02-01

Full Text Available This design research aims to develop a learning activity which supports the fifth-grade students to understand measurement fraction division problems (A whole number divided by a fraction that result in a whole number answer conceptually. Furthermore, how students solve the fraction division problem using models is also analyzed.  Data for the retrospective analysis is collected through two teaching experiments in the form of students’ work, field notes, and some part of classroom discussions. The important findings in this research are: 1 the developed learning activity namely Motivation Cards support students understand that  3 divided by one-half means how many one-half are in 3 through models. However, when the divisor is not a unit fraction they could not directly relate the unshaded part in area model for example. 2 area model is proper model to be firstly introduced when the students work on fraction division. 3 understanding this kind of fraction division help students understand other measurement fraction division where both divisor and dividend are fractions. 4 the learning activity supports the development of character values for students.    

The Ghosts of Omdurman

Science.gov (United States)

1991-01-01

up, and the Allies played babysitter .’" The limited land warfare that occurred offered nothing really new . Despite talk of operational innovations in...certainly had an edge in firepower. Though outnumbered, the allies made the most of contemporary technology , thanks to training with bolt action rifles...nor will a US armored division much concern the New People’s Army. To meet future challenges, America’s Army must tum from the warm and well-deserved

Fragile Victory

Science.gov (United States)

1994-02-08

units, in addition to the armored and mechanized divisions north of Kuwait City, comprised the VIII Tank Corps. The goalies , located on the northern... pull the Saudi fat out of an August fire. Utilizing the opposed mechanized movement rates established by the Army’s CACDA Jiffy III War Game, Volume...against an enemy who frequently was unwilling "to pull the trigger". Our national will, untested due to the quick, bloodless nature of the war, probably

U.S. Army Space Operational Narrative

Science.gov (United States)

2012-03-20

fire, and effects ( MFE ), the operational support (OS), and the functional support division (FSD); it is further divided into many more specialties...cyberspace expertise at the highest levels is a must for the Army. Both ARCYBERCOM and USASMDC/ARSTRAT commands are key positions filled by MFE officers... MFE officers with the majority from infantry and armor (31). The FA, AD, and EN branches will round out the top five.47 Half of the Army branches are

Wavefront division digital holography

Science.gov (United States)

Zhang, Wenhui; Cao, Liangcai; Li, Rujia; Zhang, Hua; Zhang, Hao; Jiang, Qiang; Jin, Guofan

2018-05-01

Digital holography (DH), mostly Mach-Zehnder configuration based, belongs to non-common path amplitude splitting interference imaging whose stability and fringe contrast are environmental sensitive. This paper presents a wavefront division DH configuration with both high stability and high-contrast fringes benefitting from quasi common path wavefront-splitting interference. In our proposal, two spherical waves with similar curvature coming from the same wavefront are used, which makes full use of the physical sampling capacity of the detectors. The interference fringe spacing can be adjusted flexibly for both in-line and off-axis mode due to the independent modulation to these two waves. Only a few optical elements, including the mirror-beam splitter interference component, are used without strict alignments, which makes it robust and easy-to-implement. The proposed wavefront division DH promotes interference imaging physics into the practical and miniaturized a step forward. The feasibility of this method is proved by the imaging of a resolution target and a water flea.

Chemical and Laser Sciences Division: Annual report, 1987

International Nuclear Information System (INIS)

1988-01-01

As the Chemical and Laser Sciences Division concludes its first year, the Division personnel can be proud of their many scientific and technical accomplishments. Among the important milestones which the Division achieved were significant demonstrations of the process performance in the Special Isotope Separation program, of beam sensing techniques for the NPB program, and of optical angular multiplexing and energy extraction from the ICF KrF laser. In addition, the Los Alamos FTS was brought to operational status and the Bright Source attained intensities on the order of 10 17 W/cm 2 . A few highlights of these and other research and development activities are presented in the following sections of this report

Radiochemistry Division annual progress report 1989

International Nuclear Information System (INIS)

1990-01-01

The research and development activities of the Division during 1989 are briefly described in the form of individual summaries arranged under the headings: (1)Nuclear chemistry, (2)Actinide chemistry, and (3)Spectroscopy. In the field of nuclear chemistry, main emphasis is on studies in fission chemistry. R and D work in actinide chemistry area is oriented towards study of solvent extraction behaviour of actinide ions from aqueous solutions. The spectroscpoic studies are mainly concerned with EPR investigations. A list of publications by the scientist of the division is given at the end. (author). 22 figs., 39 tabs

Standard NIJ 0115.00 za testiranje otpornosti zaštitnih prsluka na ubode nožem i predmetima sa oštrim vrhom / NIJ 0115.00 standard for testing stab resistance of body armor

Directory of Open Access Journals (Sweden)

Đuro Jovanić

2008-04-01

Full Text Available Standard NIJ 0115.00 (prema Nacionalnom institutu pravde SAD, namenjen je za utvrđivanje minimuma tehničkih zahteva i metoda ispitivanja otpornosti zaštitnih prsluka, koji treba da zaštite gornji deo tela od uboda nožem i predmetima sa oštrim vrhom. Područje primene ovog standarda ograničeno je samo na pretnje ubodima, a ne na balističke pretnje, poput onih koje su obuhvaćene standardom NIJ 0101.04 za testiranje balističke otpornosti zaštitnih prsluka. / In this work made presentation of NIJ 0115.04. (National Institute of Justice standard, witch purpose is to establish minimum performance requirements and methods of testing for the stab resistance of body armor intended to protect the torso against slash and stab threats. The scope of the standard is limited to stab resistance only; the standard does not address ballistic threats, as those are covered by NIJ Standard 0101.04. Ballistic Resistance of Personal Body Armor.

THE INFLUENCE OF CAFFEINE ON MITOTIC DIVISION AT CAPSICUM ANNUUM L.

Directory of Open Access Journals (Sweden)

Elena Rosu

2006-08-01

Full Text Available The paper presents, the caffeine effects in mitotic division at Capsicum annuum L.. The treatment has determined the lessening of the mitotic index (comparative with the control variant, until mitotic division total inhibition, as well as an growth frequency of division aberation in anaphase and telophase.

Seroprevalence of hepatitis C in pregnant females of Hazara division

International Nuclear Information System (INIS)

Gul, N.; Idris, M.; Sarwar, J.; Suleman, M.

2009-01-01

Hepatitis C Virus (HCV), the causative agent of Hepatitis C is prevalent in different countries including Pakistan. Studies have been conducted on various aspects of HCV in Pakistan. The present study was planed to see the prevalence of hepatitis C in pregnant females of Hazara Division. Five hundred pregnant females of reproductive age group from Hazara Division selected by non probability convenient sampling technique were studied from 1, March 2006 to 28, February 2007 at Ayub Teaching Hospital, and District Head quarter Hospitals Abbottabad, Haripur and Mansehra. After initial serving by immunology technique positive cases were confirmed by Enzyme Linked Immunosorbent Essay (ELISA). Seroprevalence of HCV in pregnant females of Hazara division was 8.9%. Females aged from 25-35 constituted the largest group among positive cases. HCV was more prevalent in District Abbottabad as compared to the other districts of Hazara division. Seroprevalence of HCV in pregnant females of Hazara Division is different from the figures already reported form the other parts of Pakistan. (author)

Mentorship programs for faculty development in academic general pediatric divisions.

Science.gov (United States)

Takagishi, Jennifer; Dabrow, Sharon

2011-01-01

Introduction. Mentoring relationships have been shown to support academicians in areas of research, work/life balance, and promotion. Methods. General pediatric division chiefs accessed an electronic survey asking about mentorship relationships, their ability to create a mentorship program, and resources needed. Results. Dyadic mentorship programs were available at 53% of divisions. Peer mentorship programs were available at 27% of divisions. Overall, 84% of chiefs believed that dyadic mentorship would benefit their faculty. 91% of chiefs believed that peer mentorship would benefit their faculty. Chiefs were interested in starting peer (57%) or dyadic (55%) mentorship programs. Few divisions had a peer mentorship program available, whereas 24% already had a dyadic program. 43% of chiefs felt that they had the tools to start a program. Many tools are needed to create a program. Discussion. General pediatric division chiefs acknowledge the benefits of mentoring relationships, and some have programs in place. Many need tools to create them. Pediatric societies could facilitate this critical area of professional development.

Chemical Technology Division annual technical report, 2001

International Nuclear Information System (INIS)

Lewis, D.; Gay, E. C.; Miller, J. C.; Boparai, A. S.

2002-01-01

The Chemical Technology Division (CMT) is one of eight engineering research divisions within Argonne National Laboratory, one of the U.S. government's oldest and largest research laboratories. The University of Chicago oversees the laboratory on behalf of the U.S. Department of Energy (DOE). Argonne's mission is to conduct basic scientific research, to operate national scientific facilities, to enhance the nation's energy resources, and to develop better ways to manage environmental problems. Argonne has the further responsibility of strengthening the nation's technology base by developing innovative technology and transferring it to industry. CMT is a diverse early-stage engineering organization, specializing in the treatment of spent nuclear fuel, development of advanced electrochemical power sources, and management of both high- and low-level nuclear wastes. Although this work is often indistinguishable from basic research, our efforts are directed toward the practical devices and processes that are covered by Argonne's mission. Additionally, the Division operates the Analytical Chemistry Laboratory and Environment, Safety, and Health Analytical Chemistry services, which provide a broad range of analytical services to Argonne and other organizations. The Division is multidisciplinary. Its people have formal training as ceramists; physicists; material scientists; electrical, mechanical, chemical, and nuclear engineers; and chemists. They have experience working in academia; urban planning; and the petroleum, aluminum, and automotive industries. Their skills include catalysis, ceramics, electrochemistry, metallurgy, nuclear magnetic resonance spectroscopy, and petroleum refining, as well as the development of nuclear waste forms, batteries, and high-temperature super-conductors. The Division's wide-ranging expertise finds ready application in solving energy and environmental problems. Division personnel are frequently called on by governmental and industrial

Stationary Size Distributions of Growing Cells with Binary and Multiple Cell Division

Science.gov (United States)

Rading, M. M.; Engel, T. A.; Lipowsky, R.; Valleriani, A.

2011-10-01

Populations of unicellular organisms that grow under constant environmental conditions are considered theoretically. The size distribution of these cells is calculated analytically, both for the usual process of binary division, in which one mother cell produces always two daughter cells, and for the more complex process of multiple division, in which one mother cell can produce 2 n daughter cells with n=1,2,3,… . The latter mode of division is inspired by the unicellular algae Chlamydomonas reinhardtii. The uniform response of the whole population to different environmental conditions is encoded in the individual rates of growth and division of the cells. The analytical treatment of the problem is based on size-dependent rules for cell growth and stochastic transition processes for cell division. The comparison between binary and multiple division shows that these different division processes lead to qualitatively different results for the size distribution and the population growth rates.

Computers in Nuclear Physics Division

International Nuclear Information System (INIS)

Kowalczyk, M.; Tarasiuk, J.; Srebrny, J.

1997-01-01

Improving of the computer equipment in Nuclear Physics Division is described. It include: new computer equipment and hardware upgrading, software developing, new programs for computer booting and modernization of data acquisition systems

Investigation into constant envelope orthogonal frequency division multiplexing for polarization-division multiplexing coherent optical communication

Science.gov (United States)

Li, Yupeng; Ding, Ding

2017-09-01

Benefiting from the high spectral efficiency and low peak-to-average power ratio, constant envelope orthogonal frequency division multiplexing (OFDM) is a promising technique in coherent optical communication. Polarization-division multiplexing (PDM) has been employed as an effective way to double the transmission capacity in the commercial 100 Gb/s PDM-QPSK system. We investigated constant envelope OFDM together with PDM. Simulation results show that the acceptable maximum launch power into the fiber improves 10 and 6 dB for 80- and 320-km transmission, respectively (compared with the conventional PDM OFDM system). The maximum reachable distance of the constant envelope OFDM system is able to reach 800 km, and even 1200 km is reachable if an ideal erbium doped fiber amplifier is employed.

Morphological and hematological studies of Trypanosoma spp. infecting ornamental armored catfish from Guamá River-PA, Brazil

Directory of Open Access Journals (Sweden)

Rodrigo Y. Fujimoto

2013-09-01

Full Text Available A total of 281 specimens of freshwater armored ornamental fish species (Leporacanthicus galaxias, Lasiancistrus saetiger, Cochliodon sp., Hypostomus sp., Pseudacanthicus spinosus, Ancistrus sp. and Rineloricaria cf. lanceolata were captured at the hydrological basin of Guamá River, Pará, Brazil. The infection by Trypanosoma spp. was inspected. The morphological and morphometric characterization of the parasites and the hematological parameters were determined. Leporacanthicus galaxias and Pseudacanthicus spinosus presented 100% infection prevalence, and the other species showed a variable prevalence of infection. The parasites showed clearly different morphotypes and dimensions, and probably belong to different species. The hematological response to the infection varied with the host. Cochliodon sp. showed no differences between infected and not infected fish. In other species several modifications on some hematological parameters were found, but apparently without causing disease. It is emphasized the possibility of introduction of the parasites in new environments due to the artificial movements of these ornamental fish.

Progress report - physical sciences TASCC division 1991 January 01 - June 30

International Nuclear Information System (INIS)

Hardy, J.C.

1991-09-01

This is the second in a new series of reports of the work of the TASCC Division since the creation of the Physical Sciences Unit in 1990. Physical Sciences comprises four main sectors, namely the TASCC, Physics and Chemistry Divisions, and the National Fusion Program Management Office. Physics Division is responsible for research and development in the areas of condensed matter physics, neutron and neutrino physics, and accelerator physics, while TASCC Division deals with research performed with the Tandem and Superconducting Cyclotron accelerators, primarily in the field of Heavy Ion Nuclear Physics

Ploidy-Dependent Unreductional Meiotic Cell Division in Polyploid Wheat

Science.gov (United States)

Meiosis includes one round of DNA replication and two successive nuclear divisions, i.e. meiosis I (reductional) and meiosis II (equational). This specialized cell division reduces chromosomes in half and generates haploid gametes in sexual reproduction of eukaryotes. It ensures faithful transmiss...

Isotope and Nuclear Chemistry Division annual report, FY 1988

International Nuclear Information System (INIS)

1989-06-01

This report describes some of the major research and development programs of the Isotope and Nuclear Chemistry Division during FY 1988. The report includes articles on weapons chemistry, biochemistry and nuclear medicine, nuclear structure and reactions, and the INC Division facilities and laboratories

Physics, Computer Science and Mathematics Division annual report, 1 January-31 December 1983

Energy Technology Data Exchange (ETDEWEB)

Jackson, J.D.

1984-08-01

This report summarizes the research performed in the Physics, Computer Science and Mathematics Division of the Lawrence Berkeley Laboratory during calendar year 1983. The major activity of the Division is research in high-energy physics, both experimental and theoretical, and research and development in associated technologies. A smaller, but still significant, program is in computer science and applied mathematics. During 1983 there were approximately 160 people in the Division active in or supporting high-energy physics research, including about 40 graduate students. In computer science and mathematics, the total staff, including students and faculty, was roughly 50. Because of the creation in late 1983 of a Computing Division at LBL and the transfer of the Computer Science activities to the new Division, this annual report is the last from the Physics, Computer Science and Mathematics Division. In December 1983 the Division reverted to its historic name, the Physics Division. Its future annual reports will document high energy physics activities and also those of its Mathematics Department.

Physics, Computer Science and Mathematics Division annual report, 1 January-31 December 1983

International Nuclear Information System (INIS)

Jackson, J.D.

1984-08-01

This report summarizes the research performed in the Physics, Computer Science and Mathematics Division of the Lawrence Berkeley Laboratory during calendar year 1983. The major activity of the Division is research in high-energy physics, both experimental and theoretical, and research and development in associated technologies. A smaller, but still significant, program is in computer science and applied mathematics. During 1983 there were approximately 160 people in the Division active in or supporting high-energy physics research, including about 40 graduate students. In computer science and mathematics, the total staff, including students and faculty, was roughly 50. Because of the creation in late 1983 of a Computing Division at LBL and the transfer of the Computer Science activities to the new Division, this annual report is the last from the Physics, Computer Science and Mathematics Division. In December 1983 the Division reverted to its historic name, the Physics Division. Its future annual reports will document high energy physics activities and also those of its Mathematics Department

Time-division optical interconnects for local-area and micro-area networks

Science.gov (United States)

Krol, Mark F.; Boncek, Raymond K.; Johns, Steven T.; Stacy, John L.

1991-12-01

This report describes the development of an optical Time-Division Multiple-Access (TDMA) interconnect suitable for applications in local-area and micro-area networks. The advantages of using time-division techniques instead of frequency-division, wavelength-division, or code-division techniques in a shared-medium environment are discussed in detail. Furthermore, a detailed description of the TDMA architecture is presented along with various experiments pertaining to the actual components needed to implement the system. Finally, experimental data is presented for an actual optical TDMA test bed. The experimental data demonstrates the feasibility of the architecture, and shows that currently the system has the capability to accommodate up to 50 channels. The bit-error-rate per channel was measured to be less than 10(exp -9) for pseudo-random bit-sequences.

Bidding in common value fair division games

OpenAIRE

Brünner, Tobias; Becker, Alice

2013-01-01

In a fair division game an indivisible object with an unknown common value is owned by a group of individuals and should be allocated to one of them while the others are compensated monetarily. Implementing fair division games in the lab, we fi nd many occurrences of the winner's curse under the first-price rule but only few occurrences under the second-price rule. Moreover, bidding behavior is very heterogeneous across subjects. A considerable share of our subjects anticipates that other bid...

Fuel Chemistry Division: progress report for 1987

International Nuclear Information System (INIS)

1990-01-01

The progress of research and development activities of the Fuel Chemistry Division of the Bhabha Atomic Research Centre, Bombay, during 1987 is reported in the form of summaries which are arranged under the headings: Fuel Development Chemistry, Chemistry of Actinides, Chemical Quality Control of Fuel, and Studies related to Nuclear Material Accounting. A list of publications by the members of the Division during the report period is given at the end of the report. (M.G.B.). refs., 15 figs., 85 tabs

Bribe-proof Rules in the Division Problem

OpenAIRE

Jordi MassóAuthor-Email:; Alejandro Neme

2003-01-01

The division problem consists of allocating an amount of a perfectly divisible good among a group of n agents with single-peaked preferences. A rule maps preference profiles into n shares of the amount to be allocated. A rule is bribe-proof if no group of agents can compensate another agent to misrepresent his preference and, after an appropriate redistribution of their shares, each obtain a strictly preferred share. We characterize all bribe-proof rules as the class of efficient, strategy-pr...

Division 1137 property control system

Energy Technology Data Exchange (ETDEWEB)

Pastor, D.J.

1982-01-01

An automated data processing property control system was developed by Mobile and Remote Range Division 1137. This report describes the operation of the system and examines ways of using it in operational planning and control.

Applied Physics Division 1998 Progress Report

International Nuclear Information System (INIS)

Cecchini, M.; Crescentini, L; Ghezzi, L.; Kent, C.; Bottomei, M.

2001-01-01

This report outlines the 1998 research activities carried out by the Applied Physics Division of the Innovation Department of ENEA (Italian Agency for New Technologies, Energy and Environment). The fields addressed and discussed include: optical and electro-optical technologies (chaps. 1 and 2); accelerator technologies (chap. 3); diagnostic systems for science and engineering (chaps. 4 and 5); theory, modelling and computational methods (chaps. 6 and 7). The aim of the Applied Physics Division is to develop technologies and systems that can be directly applied by internal (ENEA) and external users in research (high-resolution spectroscopy, laser-generated soft-x-ray sources), production processes (laser material photoproduction, structural analysis), social, cultural and environmental sciences (laser remote sensing, modelling of ecosystems and population dynamics) and medicine (particle accelerator for radiotherapy). Most of the work in 1998 was performed by the division's laboratories at the Frascati, Casaccia and Bologna Research Centres of ENEA; some was done elsewhere in collaboration with other ENEA units, external laboratories and industries. A good share of the activities was carried out for international projects; in particular, the IV European Union Framework Program

Applied Physics Division 1998 Progress Report

Energy Technology Data Exchange (ETDEWEB)

Cecchini, M.; Crescentini, L; Ghezzi, L.; Kent, C.; Bottomei, M. [ENEA, Centro Ricerche Frascati, Frascati, RM (Italy). Applied physics Division

1999-07-01

This report outlines the 1998 research activities carried out by the Applied Physics Division of the Innovation Department of ENEA (Italian Agency for New Technologies, Energy and Environment). The fields addressed and discussed include: optical and electro-optical technologies (chaps. 1 and 2); accelerator technologies (chap. 3); diagnostic systems for science and engineering (chaps. 4 and 5); theory, modelling and computational methods (chaps. 6 and 7). The aim of the Applied Physics Division is to develop technologies and systems that can be directly applied by internal (ENEA) and external users in research (high-resolution spectroscopy, laser-generated soft-x-ray sources), production processes (laser material photoproduction, structural analysis), social, cultural and environmental sciences (laser remote sensing, modelling of ecosystems and population dynamics) and medicine (particle accelerator for radiotherapy). Most of the work in 1998 was performed by the division's laboratories at the Frascati, Casaccia and Bologna Research Centres of ENEA; some was done elsewhere in collaboration with other ENEA units, external laboratories and industries. A good share of the activities was carried out for international projects; in particular, the IV European Union Framework Program.

Spectroscopy Division progress report for Jan 1983 - Dec 1984

International Nuclear Information System (INIS)

Dixit, R.M.

1985-01-01

The Research and Development (R and D) activities of the Spectroscopy Division of the Bhabha Atomic Research Centre, Bombay, during the period from January 1983 to December 1984 are reported. The main thrust of the activities of the Division is directed towards meeting the spectrochemical analytical requirements of the nuclear energy programmes and the related R and D projects of the Department of Atomic Energy. These activities are described in the form of summaries grouped under the headings:(1) analyses by optical emission, X-ray fluorescence, X-ray excited optical luminescence and other techniques, (2) atomic, molecular and solid state spectroscopy, (3) optics and thin films, and (4) electronic instrumentation. Two feature articles which are included in the report bring out the salient features of X-ray absorption fine structure spectroscopy (EXFAS) and laser spectroscopic techniques for trace analysis and describe the Division's efforts in setting up facilities to carry out work in these emerging fields. Other activities of the Division are teaching trainees and guiding research leading to M.Sc. and Ph.D. degrees. A list of papers published in journals and papers presented at conferences, symposia etc. by the staff-members of the Division is given. A divisional staff chart is also given. (M.G.B.)

75 FR 45151 - National Security Division; Agency Information Collection Activities: Proposed Collection...

Science.gov (United States)

2010-08-02

... DEPARTMENT OF JUSTICE [OMB Number 1124-0006] National Security Division; Agency Information...), National Security Division (NSD), will be submitting the following information collection request to the..., 10th & Constitution Avenue, NW., National Security Division, Counterespionage Section/Registration Unit...

Biology Division. Progress report, August 1, 1982-September 30, 1983

International Nuclear Information System (INIS)

1984-01-01

The Biology Division is the component of the Oak Ridge National Laboratory that investigates the potential adverse health effects of energy-related substances. The body of this report provides summaries of the aims, scope and progress of the research of groups of investigators in the Division during the period of August 1, 1982, through September 30, 1983. At the end of each summary is a list of publications covering the same period (published or accepted for publication). For convenience, the summaries are assembled under Sections in accordance with the current organizational structure of the Biology Division; each Section begins with an overview. It will be apparent, however, that currents run throughout the Division and that the various programs support and interact with each other

Biology Division. Progress report, August 1, 1982-September 30, 1983

Energy Technology Data Exchange (ETDEWEB)

1984-01-01

The Biology Division is the component of the Oak Ridge National Laboratory that investigates the potential adverse health effects of energy-related substances. The body of this report provides summaries of the aims, scope and progress of the research of groups of investigators in the Division during the period of August 1, 1982, through September 30, 1983. At the end of each summary is a list of publications covering the same period (published or accepted for publication). For convenience, the summaries are assembled under Sections in accordance with the current organizational structure of the Biology Division; each Section begins with an overview. It will be apparent, however, that currents run throughout the Division and that the various programs support and interact with each other.

UKAEA Government Division Annual Review 1994-95

International Nuclear Information System (INIS)

1995-01-01

This is the first annual review of the United Kingdom Atomic Energy Authority (UKAEA) Government Division. The Division was set up in April 1994 with the primary responsibility of completing the UKAEA's nuclear mission by caring for and decommissioning the radioactive facilities used in pursuit of the national nuclear programme over the past 50 years; this includes the safe disposal of the resulting radioactive waste. The progress made in the first year towards carrying out this responsibility at the lowest cost while continuing to ensure safety and protection of the environment is reported. Other responsibilities of Government Division which are reviewed include: management of the UKAEA's sites, buildings and operating facilities; oversight of the United Kingdom fusion research programme and provision for the Joint European Torus which is situated next to the Culham fusion site; and the UKAEA Constabulary. Appended to the review are a financial statement and a list of the main decommissioning tasks. (UK)

Analytical Chemistry Division : annual report (for) 1985

International Nuclear Information System (INIS)

Mahadevan, N.

1986-01-01

An account of the various activities of the Analytical Chemistry Division of the Bhabha Atomic Research Centre, Bombay, during 1985 is presented. The main function of the Division is to provide chemical analysis support to India's atomic energy programme. In addition, the Division also offers its analytical services, mostly for measurement of concentrations at trace levels to Indian industries and other research organization in the country. A list of these determinations is given. The report also describes the research and development (R and D) activities - both completed and in progress, in the form of individual summaries. During the year an ultra trace analytical laboratory for analysis of critical samples without contamination was set up using indigenous material and technology. Publications and training activities of the staff, training of the staff from other institution, guidance by the staff for post-graduate degree and invited talks by the staff are listed in the appendices at the end of the report. (M.G.B.)

Energy Division annual progress report for period ending September 30, 1992

Energy Technology Data Exchange (ETDEWEB)

Counce, D.M.; Wolff, P.P. [eds.

1993-04-01

Energy Division`s mission is to provide innovative solutions to energy and related Issues of national and global importance through interdisciplinary research and development. Its goals and accomplishments are described in this annual progress report for FY 1992. Energy Division`s total expenditures in FY 1992 were $42.8 million. The work is supported by the US Department of Energy, the US Department of Defense, many other federal agencies, and some private organizations. Disciplines of the 116.5 technical staff members include engineering, social sciences, physical and life sciences, and mathematics and statistics. The division`s programmatic activities cover three main areas: (1) analysis and assessment, (2) energy conservation technologies, and (3) military transportation systems. Analysis and assessment activities involve energy and resource analysis, preparation of environmental assessments and impact statements, research on waste management, technology transfer, analysis of energy and environmental needs in developing countries, and civilian transportation analysis. Energy conservation technologies focus on electric power systems, building envelopes (walls, foundations, roofs, attics, and materials), and methods to improve energy efficiency in existing buildings. Military transportation systems conduct research for sponsors within the US military to improve the efficiency of military deployment, scheduling, and transportation coordination. Much of Energy Division`s research is valuable to other organizations as well as to sponsors. This information is disseminated by the staff`s involvement in professional and trade organizations and workshops; joint research with universities and private-sector firms; collaboration with state and local governments; presentation of work at conferences; and publication of research results in journals, reports, and conference proceedings.

On the interrelation of multiplication and division in secondary school children

Directory of Open Access Journals (Sweden)

Stefan eHuber

2013-10-01

Full Text Available Multiplication and division are conceptually inversely related: Each division problem can be transformed into as a multiplication problem and vice versa. Recent research has indicated strong developmental parallels between multiplication and division in primary school children. In this study, we were interested in (i whether these developmental parallels persist into secondary school, (ii whether similar developmental parallels can be observed for simple and complex problems, (iii whether skill level modulates this relationship, and (iv whether the correlations are specific and not driven by general cognitive or arithmetic abilities.Therefore, we assessed performance of 5th and 6th graders attending two secondary school types of the German educational system in simple and complex multiplication as well as division while controlling for nonverbal intelligence, short-term memory, and other arithmetic abilities. Accordingly, we collected data from students differing in skills levels due to either age (5th and 6th grade or school type (general and intermediate secondary school.We observed moderate to strong bivariate and partial correlations between multiplication and division with correlations being higher for simple tasks but nevertheless reliable for complex tasks. Moreover, the association between simple multiplication and division depended on students’ skill levels as reflected by school types, but not by age. Partial correlations were higher for intermediate than for general secondary school children.In sum, these findings emphasize the importance of the inverse relationship between multiplication and division which persists into later developmental stages. However, evidence for skill-related differences in the relationship between multiplication and division was restricted to the differences for school types.

Radiochemistry Division: triennial progress report (for) 1983-1985

International Nuclear Information System (INIS)

Datta, T.

1987-01-01

The present report includes contributions pertaining to the studies of nuclear and chemical properties of actinides. These studies have been mostly concerned with the basic investigation, besides the research and development work connected with chemical quality control of plutonium-based fuels for trace metallic constituents. The nuclear properties are being studied in the Nuclear Chemistry and Instrumentation Section while the chemical properties are being studied in the Actinide Chemistry Section and the Spectroscopy Section. The work in the Actinide Chemistry Section deals essentially with properties of ions in solutions and preparation of solid compounds, to understand the complexing behaviour of actinides. The work in the Spectroscopy Section is concerned essentially with the study of actinide solids using EPR, TSL and optical spectroscopic techniques. The considerable advances made in the basic study of actinides are reflected in the number of publications in well-known international journals. The research and development work of the Division is fully supported by Instrumentation Group of the Division which looks after the maintenance of instruments of not only the Radiochemistry Division but also the Fuel Chemistry Division and design and fabrication of special electronic instruments needed for the research and development work. (author)

AC/ARNG Integrated Division Concept Study, Main Report, Volume 1

National Research Council Canada - National Science Library

Twohig, John

1997-01-01

...) division headquarters. The US Army Training and Doctrine Command (TRADOC) was tasked to conduct a viability assessment of the AC/ARNG Integrated Division concept and focus on merits and implementation issues...

75 FR 45153 - National Security Division; Agency Information Collection Activities: Proposed Collection...

Science.gov (United States)

2010-08-02

... DEPARTMENT OF JUSTICE [OMB Number 1124-0001] National Security Division; Agency Information..., 10th & Constitution Avenue, NW., National Security Division, Counterespionage Section/Registration Unit... Justice sponsoring the collection: Form Number: NSD- 1. National Security Division, U.S. Department of...

28 CFR 3.2 - Assistant Attorney General, Criminal Division.

Science.gov (United States)

2010-07-01

... 28 Judicial Administration 1 2010-07-01 2010-07-01 false Assistant Attorney General, Criminal... Attorney General, Criminal Division. The Assistant Attorney General, Criminal Division, is authorized to exercise the power and authority of and to perform the functions vested in the Attorney General by the Act...

Plant cortical microtubule dynamics and cell division plane orientation

NARCIS (Netherlands)

Chakrabortty, Bandan

2017-01-01

This thesis work aimed at a better understanding of the molecular basis of oriented cell division in plant cell. As, the efficiency of plant morphogenesis depends on oriented cell division, this work should contribute towards a fundamental understanding of the molecular basis of efficient plant

De la motte au château d’artillerie, la fouille du château de Guingamp (Côtes-d’Armor

Directory of Open Access Journals (Sweden)

Laurent Beuchet

2010-02-01

Full Text Available L’opération d’archéologie préventive du château de Guingamp (Côtes-d’Armor a été réalisée dans le cadre d'un projet de création d'une salle culturelle sur le site du château. La fouille a été menée sur une superficie de 2000 m², sur une durée effective de cinq mois entre octobre 2004 et mars 2005, avec un effectif moyen de sept personnes.À l’issue de la fouille, trois phases principales d’occupation peuvent être identifiées :la motte des Comtes de Guingamp (XIe-XIIe s. ;une enceinte polygon...

75 FR 45152 - National Security Division: Agency Information Collection Activities: Proposed Collection...

Science.gov (United States)

2010-08-02

... DEPARTMENT OF JUSTICE [OMB Number 1124-0004] National Security Division: Agency Information...), National Security Division (NSD), will be submitting the following information collection request to the... write to U.S. Department of Justice, 10th & Constitution Avenue, NW., National Security Division...

Fielding a Division Staff in the Modern Day

Science.gov (United States)

2016-06-10

Team CGSC Command and General Staff College CSA Chief of Staff of the Army DART Domestic All-Hazards Response Team EOD Explosive Ordnance Disposal...located at Fort Leavenworth. Conclusion This paper reviewed the current purpose, size, training, and structure of division staffs in the active duty...Response Team ( DART ), both supported by the National Guard division headquarters. Coordinated with the Department of Defense and Department of State

The Modular need for the Division Signal Battalion

Science.gov (United States)

2017-06-09

Division Signal Battalion, Leader Development, Organizational Design, Modularity, Force Structure , Army Warfighting Challenge (AWFC) #20 16. SECURITY...Signal Corps men, equipment , and communications installations tailored to fit the situation.”47 In its initial conception, the cellular structure ...force structure than the Division-centric force of the day.”93 30 days after the issuance of this guidance, designs based on the pilot program began

Bendix Kansas City Division technological spinoff through 1978

International Nuclear Information System (INIS)

Barnes, H.T.

1979-02-01

The results of work of Bendix Kansas City Division are made available in the form of technical reports that are processed through the DOE Technical Information Center in Oak Ridge. The present report lists the documents released by the Division, along with author and subject indexes. Drawing sets released are also listed. Locations of report collections in the U.S., other countries, and international agencies are provided

Silicon Chip-to-Chip Mode-Division Multiplexing

DEFF Research Database (Denmark)

Baumann, Jan Markus; Porto da Silva, Edson; Ding, Yunhong

2018-01-01

A chip-to-chip mode-division multiplexing connection is demonstrated using a pair of multiplexers/demultiplexers fabricated on the silicon-on-insulator platform. Successful mode multiplexing and demultiplexing is experimentally demonstrated, using the LP01, LP11a and LP11b modes.......A chip-to-chip mode-division multiplexing connection is demonstrated using a pair of multiplexers/demultiplexers fabricated on the silicon-on-insulator platform. Successful mode multiplexing and demultiplexing is experimentally demonstrated, using the LP01, LP11a and LP11b modes....

5 CFR 831.641 - Division of a survivor annuity.

Science.gov (United States)

2010-01-01

... 5 Administrative Personnel 2 2010-01-01 2010-01-01 false Division of a survivor annuity. 831.641... REGULATIONS (CONTINUED) RETIREMENT Survivor Annuities Eligibility § 831.641 Division of a survivor annuity. (a... annuities (not including any benefits based on an election of an insurable interest annuity) payable based...

5 CFR 842.613 - Division of a survivor annuity.

Science.gov (United States)

2010-01-01

... 5 Administrative Personnel 2 2010-01-01 2010-01-01 false Division of a survivor annuity. 842.613... REGULATIONS (CONTINUED) FEDERAL EMPLOYEES RETIREMENT SYSTEM-BASIC ANNUITY Survivor Elections § 842.613 Division of a survivor annuity. (a) The maximum combined total of all current and former spouse annuities...

Order Division Automated System.

Science.gov (United States)

Kniemeyer, Justin M.; And Others

This publication was prepared by the Order Division Automation Project staff to fulfill the Library of Congress' requirement to document all automation efforts. The report was originally intended for internal use only and not for distribution outside the Library. It is now felt that the library community at-large may have an interest in the…

Comprehensive Review on Divisible Load Theory: Concepts, Strategies, and Approaches

Directory of Open Access Journals (Sweden)

Shamsollah Ghanbari

2014-01-01

Full Text Available There is extensive literature concerning the divisible load theory. The divisible load theory is mainly applied for scheduling in the area of distributed computing. It is based on the fact that the load can be divided into some arbitrarily independent parts, in which each part can be processed independently by a processor. This paper reviews the literature concerning the divisible load theory, while focusing on the details of the basic concepts, approaches, strategies, typologies, and open problems.

Health, Safety, and Environment Division

Energy Technology Data Exchange (ETDEWEB)

Wade, C [comp.

1992-01-01

The primary responsibility of the Health, Safety, and Environmental (HSE) Division at the Los Alamos National Laboratory is to provide comprehensive occupational health and safety programs, waste processing, and environmental protection. These activities are designed to protect the worker, the public, and the environment. Meeting these responsibilities requires expertise in many disciplines, including radiation protection, industrial hygiene, safety, occupational medicine, environmental science and engineering, analytical chemistry, epidemiology, and waste management. New and challenging health, safety, and environmental problems occasionally arise from the diverse research and development work of the Laboratory, and research programs in HSE Division often stem from these applied needs. These programs continue but are also extended, as needed, to study specific problems for the Department of Energy. The results of these programs help develop better practices in occupational health and safety, radiation protection, and environmental science.

Biology Division progress report, October 1, 1984-September 30, 1985

Energy Technology Data Exchange (ETDEWEB)

1986-01-01

The body of this report provides summaries of the aims, scope and progress of the research by groups of investigators in the Division during the period of October 1, 1984, through September 30, 1985. At the end of each summary is a list of publications covering the same period. For convenience, the summaries are assembled under Sections in accordance with the current organizational structure of the Biology Division; each Section begins with an overview. It will be apparent, however, tha crosscurrents run throughout the Division and that the various programs support and interact with each other. In addition, this report includes information on the Division's educational activities, Advisory Committee, seminar program, and international interactions, as well as extramural activities of staff members, abstracts for technical meetings, and funding and personnel levels.

Biology Division progress report, October 1, 1984-September 30, 1985

International Nuclear Information System (INIS)

1986-01-01

The body of this report provides summaries of the aims, scope and progress of the research by groups of investigators in the Division during the period of October 1, 1984, through September 30, 1985. At the end of each summary is a list of publications covering the same period. For convenience, the summaries are assembled under Sections in accordance with the current organizational structure of the Biology Division; each Section begins with an overview. It will be apparent, however, tha crosscurrents run throughout the Division and that the various programs support and interact with each other. In addition, this report includes information on the Division's educational activities, Advisory Committee, seminar program, and international interactions, as well as extramural activities of staff members, abstracts for technical meetings, and funding and personnel levels

Physics Division progress report, January 1, 1991--December 31, 1991

International Nuclear Information System (INIS)

Shera, E.B.; Hollen, G.Y.

1992-06-01

This report provides selected accounts of significant progress in research and development achieved by Physics Division personnel during the period January 1, 1991, through December 31, 1991. It also provides a general description of the goals and interests of the Division, very brief descriptions of projects in the Division, and a list of publications produced during this period. The report represents the three main areas of experimental research and development in which the Physics Division serves the needs of Los Alamos National Laboratory and the nation in defense and basic sciences: (1) fundamental research in nuclear and particle physics, condensed-matter physics, and biophysics; (2) laser physics and applications, especially to high-density plasmas; (3) defense physics, including the development of diagnostic methods for weapons tests, weapons-related high energy-density physics, and other programs

Chemical Technology Division annual technical report, 2001

International Nuclear Information System (INIS)

Lewis, D.; Gay, E. C.; Miller, J. C.; Boparai, A. S.

2002-01-01

The Chemical Technology Division (CMT) is one of eight engineering research divisions within Argonne National Laboratory, one of the U.S. government's oldest and largest research laboratories. The University of Chicago oversees the laboratory on behalf of the U.S. Department of Energy (DOE). Argonne's mission is to conduct basic scientific research, to operate national scientific facilities, to enhance the nation's energy resources, and to develop better ways to manage environmental problems. Argonne has the further responsibility of strengthening the nation's technology base by developing innovative technology and transferring it to industry. CMT is a diverse early-stage engineering organization, specializing in the treatment of spent nuclear fuel, development of advanced electrochemical power sources, and management of both high- and low-level nuclear wastes. Although this work is often indistinguishable from basic research, our efforts are directed toward the practical devices and processes that are covered by Argonne's mission. Additionally, the Division operates the Analytical Chemistry Laboratory and Environment, Safety, and Health Analytical Chemistry services, which provide a broad range of analytical services to Argonne and other organizations. The Division is multidisciplinary. Its people have formal training as ceramists; physicists; material scientists; electrical, mechanical, chemical, and nuclear engineers; and chemists. They have experience working in academia; urban planning; and the petroleum, aluminum, and automotive industries. Their skills include catalysis, ceramics, electrochemistry, metallurgy, nuclear magnetic resonance spectroscopy, and petroleum refining, as well as the development of nuclear waste forms, batteries, and high-temperature superconductors

CSIR Division of Mining Technology annual review 1993/94

Energy Technology Data Exchange (ETDEWEB)

1994-01-01

The Division of Mining Technology of the CSIR (Council for Scientific and Industrial Research) works in partnership with the mining industry to solve problems threatening the health, safety and well-being of the workforce, and the productivity of mining operations through the development and implementation of knowledge and technology. The annual review describes the Division's research projects in the following field: rock engineering (for gold, platinum and coal mining); mining environment; occupational hygiene; surface environment; and mining equipment and systems (systems and equipment, orebody information, coal mining and causes of accidents). Details are also given of the Division's publications, research and consultancy services and information centre.

Physics Division Argonne National Laboratory description of the programs and facilities.

Energy Technology Data Exchange (ETDEWEB)

Thayer, K.J. [ed.

1999-05-24

The ANL Physics Division traces its roots to nuclear physics research at the University of Chicago around the time of the second world war. Following the move from the University of Chicago out to the present Argonne site and the formation of Argonne National Laboratory: the Physics Division has had a tradition of research into fundamental aspects of nuclear and atomic physics. Initially, the emphasis was on areas such as neutron physics, mass spectrometry, and theoretical studies of the nuclear shell model. Maria Goeppert Maier was an employee in the Physics Division during the time she did her Nobel-Prize-winning work on the nuclear shell model. These interests diversified and at the present time the research addresses a wide range of current problems in nuclear and atomic physics. The major emphasis of the current experimental nuclear physics research is in heavy-ion physics, centered around the ATLAS facility (Argonne Tandem-Linac Accelerator System) with its new injector providing intense, energetic ion beams over the fill mass range up to uranium. ATLAS is a designated National User Facility and is based on superconducting radio-frequency technology developed in the Physics Division. A small program continues in accelerator development. In addition, the Division has a strong program in medium-energy nuclear physics carried out at a variety of major national and international facilities. The nuclear theory research in the Division spans a wide range of interests including nuclear dynamics with subnucleonic degrees of freedom, dynamics of many-nucleon systems, nuclear structure, and heavy-ion interactions. This research makes contact with experimental research programs in intermediate-energy and heavy-ion physics, both within the Division and on the national and international scale. The Physics Division traditionally has strong connections with the nation's universities. We have many visiting faculty members and we encourage students to participate in our

Energy Division annual progress report for period ending September 30, 1993

Energy Technology Data Exchange (ETDEWEB)

Wolff, P.P. [ed.

1994-07-01

One of 17 research divisions at Oak Ridge National Laboratory, Energy Division`s mission is to provide innovative solutions to energy and related issues of national and global importance through interdisciplinary research and development. Its goals and accomplishments are described in this annual progress report for FY1993. Energy Division is committed to (1) understanding the mechanisms by which societies make choices in energy use; (2) improving society`s understanding of the environmental, social, and economic implications of technological change; (3) developing and transferring energy-efficient technologies; (4) improving transportation policy and planning; (5) enhancing basic knowledge in the social sciences as related to energy and associated issues. Energy Division`s expenditures in FY1993 totaled $42 million. The work was supported by the US DOE, DOD, many other federal agencies, and some private organizations. Disciplines of the 126.5 technical staff members include engineering, social sciences, physical and life sciences, and computer sciences and data systems. The division`s programmatic activities cover three main areas: (1) analysis and assessment, (2) energy use and delivery technologies, and (3) transportation systems. Analysis and assessment activities involve energy and resource analysis, preparation of environmental assessments and impact statements, research on emergency preparedness, transportation analysis, and analysis of energy and environmental needs in developing countries. Energy use and delivery technologies focus on electric power systems, building equipment, building envelopes (walls, foundations, roofs, attics, and materials), and methods to improve energy efficiency in existing buildings. Transportation systems research is conducted both to improve the quality of civilian transportation and for sponsors within the US military to improve the efficiency of deployment, scheduling, and transportation coordination.

Women of the Solar Physics Division

Science.gov (United States)

Dupree, Andrea K.

2007-05-01

In 1970, when the Solar Physics Division was established, the invitation to become a founding member of the Division was extended by the Organizing Committee to a group of 61 solar scientists of which 4 were women (6.6%). At the first SPD meeting in Huntsville AL (1970), 11% of the papers were given by women. Near that time (1973), women accounted for 8% of all AAS members. The representation of women in the SPD has more than doubled in percentage since the first years. Currently, women comprise about 15.5% of SPD members which, however, is less than the percentage in the AAS general membership (18%) in March 2007. In the 37 years that the SPD has existed, women have frequently held the office of Treasurer and Secretary of the Division and made notable contributions. Elske V.P. Smith was elected the first Treasurer of the SPD and that began a long tradition. Women appear to be considered exceptionally trustworthy since they have been reelected and occupied the position of Treasurer for 75% of the available terms. The Office of SPD Secretary has seen a woman for 13% of the terms. Yet women are practically absent among those in the top leadership positions and in the lists of prize winners of the SPD. Among the 21 SPD Chairs, only 1 woman, Judith T. Karpen, has held that office. The Hale Prize has been awarded 19 times in almost 3 decades, and all of the awardees have been men. Several aspects of the participation of women and their contributions to the Solar Physics Division of the AAS will be reviewed, and compared to that of the AAS and astronomy in general.

Evolution of division of labor: emergence of different activities among group members.

Science.gov (United States)

Nakahashi, Wataru; Feldman, Marcus W

2014-05-07

The division of labor is an important component of the organization of human society. However, why this division evolved in hominids requires further investigation. Archeological evidence suggests that it appeared after the emergence of Homo sapiens and contributed to the great success of our species. We develop a mathematical model to investigate under what conditions division of labor should evolve. We assume two types of resources the acquisition of which demands different skills, and study the evolution of the strategy that an individual should use to divide its lifetime into learning and using each skill. We show that division of labor likely evolves when group size is large, skill learning is important for acquiring resources, and there is food sharing within a group. We also investigate division of labor by gender under the assumption that the genders have different efficiencies in acquiring each resource. We show that division of labor by gender likely evolves when skill learning is important and the difference in efficiencies between genders in acquiring resources is large. We discuss how the results of our analysis might apply to the evolution of division of labor in hominids. Copyright © 2014 Elsevier Ltd. All rights reserved.

Activity report of Reactor Physics Division - 1988

International Nuclear Information System (INIS)

Keshavamurthy, R.S.

1989-01-01

This report highlights the progress of activities carried out during the year 1988 in Reactor Physics Division in the form of brief summaries. The topics are organised under the following subject categories:(1) nuclear data evaluation , processing and validation, (2) core physics and analysis, (3) reactor kinetics and safety analysis, (4) noise analysis and (5) radiation transport and shielding. List of publications by the members of the Division and the Reactor Physics Seminars held during the year 1988, is included at the end of report. (author). refs., figs., tabs

Chemistry Division: progress report (1983-84)

International Nuclear Information System (INIS)

Shastri, L.V.; George, A.M.

1985-01-01

This is the seventh progress report of the Chemistry Division covering the two years 1983 and 1984. The main emphasis of the Division continues to be on basic research though spin offs in high technology areas are closely pursued. Laboratory facilities have been considerably augmented during this period. Besides the design and fabrication of a crossed molecular beam chemiluminescence apparatus, a 80 MHz FTNMR and a 5nsec. excimer laser kinetic spectrometer were acquired; a 5nsec. pulsed electron accelerator would be installed in 1985. The research and development projects taken up during the VI Five Year Plan have achieved considerable progress. Only brief accounts of investigations are presented in the report. (author)

High energy physics division semiannual report of research activities

International Nuclear Information System (INIS)

Schoessow, P.; Moonier, P.; Talaga, R.; Wagner, R.

1991-08-01

This report describes the research conducted in the High Energy Physics Division of Argonne National Laboratory during the period of January 1, 1991--June 30, 1991. Topics covered here include experimental and theoretical particle physics, advanced accelerator physics, detector development, and experimental facilities research. Lists of division publications and colloquia are included

Characterization of dependencies between growth and division in budding yeast.

Science.gov (United States)

Mayhew, Michael B; Iversen, Edwin S; Hartemink, Alexander J

2017-02-01

Cell growth and division are processes vital to the proliferation and development of life. Coordination between these two processes has been recognized for decades in a variety of organisms. In the budding yeast Saccharomyces cerevisiae , this coordination or 'size control' appears as an inverse correlation between cell size and the rate of cell-cycle progression, routinely observed in G 1 prior to cell division commitment. Beyond this point, cells are presumed to complete S/G 2 /M at similar rates and in a size-independent manner. As such, studies of dependence between growth and division have focused on G 1 Moreover, in unicellular organisms, coordination between growth and division has commonly been analysed within the cycle of a single cell without accounting for correlations in growth and division characteristics between cycles of related cells. In a comprehensive analysis of three published time-lapse microscopy datasets, we analyse both intra- and inter-cycle dependencies between growth and division, revisiting assumptions about the coordination between these two processes. Interestingly, we find evidence (i) that S/G 2 /M durations are systematically longer in daughters than in mothers, (ii) of dependencies between S/G 2 /M and size at budding that echo the classical G 1 dependencies, and (iii) in contrast with recent bacterial studies, of negative dependencies between size at birth and size accumulated during the cell cycle. In addition, we develop a novel hierarchical model to uncover inter-cycle dependencies, and we find evidence for such dependencies in cells growing in sugar-poor environments. Our analysis highlights the need for experimentalists and modellers to account for new sources of cell-to-cell variation in growth and division, and our model provides a formal statistical framework for the continued study of dependencies between biological processes. © 2017 The Author(s).

Cell division cycle 20 overexpression predicts poor prognosis for patients with lung adenocarcinoma.

Science.gov (United States)

Shi, Run; Sun, Qi; Sun, Jing; Wang, Xin; Xia, Wenjie; Dong, Gaochao; Wang, Anpeng; Jiang, Feng; Xu, Lin

2017-03-01

The cell division cycle 20, a key component of spindle assembly checkpoint, is an essential activator of the anaphase-promoting complex. Aberrant expression of cell division cycle 20 has been detected in various human cancers. However, its clinical significance has never been deeply investigated in non-small-cell lung cancer. By analyzing The Cancer Genome Atlas database and using some certain online databases, we validated overexpression of cell division cycle 20 in both messenger RNA and protein levels, explored its clinical significance, and evaluated the prognostic role of cell division cycle 20 in non-small-cell lung cancer. Cell division cycle 20 expression was significantly correlated with sex (p = 0.003), histological classification (p overexpression of cell division cycle 20 was significantly associated with bigger primary tumor size (p = 0.0023), higher MKI67 level (r = 0.7618, p Overexpression of cell division cycle 20 is associated with poor prognosis in lung adenocarcinoma patients, and its overexpression can also be used to identify high-risk groups. In conclusion, cell division cycle 20 might serve as a potential biomarker for lung adenocarcinoma patients.

Uncovering the link between malfunctions in Drosophila neuroblast asymmetric cell division and tumorigenesis

Directory of Open Access Journals (Sweden)

Kelsom Corey

2012-11-01

Full Text Available Abstract Asymmetric cell division is a developmental process utilized by several organisms. On the most basic level, an asymmetric division produces two daughter cells, each possessing a different identity or fate. Drosophila melanogaster progenitor cells, referred to as neuroblasts, undergo asymmetric division to produce a daughter neuroblast and another cell known as a ganglion mother cell (GMC. There are several features of asymmetric division in Drosophila that make it a very complex process, and these aspects will be discussed at length. The cell fate determinants that play a role in specifying daughter cell fate, as well as the mechanisms behind setting up cortical polarity within neuroblasts, have proved to be essential to ensuring that neurogenesis occurs properly. The role that mitotic spindle orientation plays in coordinating asymmetric division, as well as how cell cycle regulators influence asymmetric division machinery, will also be addressed. Most significantly, malfunctions during asymmetric cell division have shown to be causally linked with neoplastic growth and tumor formation. Therefore, it is imperative that the developmental repercussions as a result of asymmetric cell division gone awry be understood.

Kinetics of human lymphocyte division and chromosomal radiosensitivity

Energy Technology Data Exchange (ETDEWEB)

Bianchi, N O; Bianchi, M S; Larramendy, M [Instituto Multidisciplinario de Biologia Celular, La Plata (Argentinia)

1979-12-01

Human blood from normal donors was irradiated with 200 R during the G/sub 0/ phase, and the X-ray sensitivity of early and late dividing lymphocytes in culture was expressed as percentage of induced dicentrics. Cells in first or subsequent divisions were individualized by BrdU-Giemsa techniques. Lymphocytes in the first division at 40, 44 and 72 h after the start of culture had a lower sensitivity to radiation than lymphocytes making their first division at 48, 52 and 56 h. It was observed that: (a) the combination of radiation followed by BrdU did not increase the clastoyenic action of X-rays, (b)X-rays in the dose and duration used in our cultures did not increase the frequency of SCEs, and (c) minor changes in culture conditions probably influenced the frequency of SCEs.

Division of Agro technology and Biosciences: Past, Present and Future

International Nuclear Information System (INIS)

Khairuddin Abdul Rahim

2012-01-01

In presenter speech, he outlined several topics regarding development of Agro technology and Biosciences Division from 31 years ago. This division started with Unit Sains Hidupan Liar under PUSPATI in 1981 and change their names to Program Isotop dan Sinaran dalam Biologi dan Pertanian under Nuclear Technology Unit (UTN) (1983). In 1990 their premise change to MINT-Tech Park. This program responsible for conducting research in agro technology using nuclear technology. Several achievements achieved by this division since established. They also succeed in mutating banana namely Novaria banana (1994), Tongkat Ali rice (1990), ground nut (2003), orchids, organic fertilizer and foliage in 2000. The vision of this division are to promote and enhance innovation and applications in nuclear technology to achieve security in food productivity, safety and quality and ecological awareness for economics competitiveness and vibrancy in agrobioindustry and community development. (author)

Physics Division progress report, January 1, 1990--December 31, 1990

International Nuclear Information System (INIS)

Shera, E.B.; Hollen, G.Y.

1991-07-01

This report provides selected accounts of significant progress in research and development achieved by Physics Division personnel during the period January 1, 1990, through December 31, 1990. It also provides a general description of the goals and interests of the Division, very brief descriptions of projects in the Division, and a list of publications produced during this period. The report represents the three main areas of experimental research and development in which the Physics Division serves the needs of Los Alamos National Laboratory and the nation in defense and basic sciences: (1) fundamental research in nuclear and particle physics, condensed-matter physics, and biophysics; (2) laser physics and applications, especially to high-density plasmas; and (3) defense physics, including the development of diagnostic methods for weapons tests, weapons-related high energy-density physics, and programs supporting the Strategic Defense Initiative

PDV2 has a dosage effect on chloroplast division in Arabidopsis.

Science.gov (United States)

Chang, Ning; Sun, Qingqing; Li, Yiqiong; Mu, Yajuan; Hu, Jinglei; Feng, Yue; Liu, Xiaomin; Gao, Hongbo

2017-03-01

PDV2 has a dosage effect on chloroplast division in Arabidopsis thaliana , but this effect may vary in different plants. Chloroplasts have to be divided as plants grow to maintain an optimized number in the cell. Chloroplasts are divided by protein complexes across the double membranes from the stroma side to the cytosolic side. PDV2 is a chloroplast division protein on the chloroplast outer membrane. It recruits the dynamin-related GTPase ARC5 to the division site. The C-terminus of PDV2 and the C-terminus of ARC6 interact in the intermembrane space, which is important for the localization of PDV2. Previously, it was shown that overexpression of PDV2 can increase the division of chloroplasts in Arabidopsis and moss, so the authors concluded that PDV2 determines the rate of chloroplast division in land plants. PDV2 was also shown to inhibit the GTPase activity of ARC5 by in vitro experiment. These results look to be contradictory. Here, we identified a null allele of PDV2 in Arabidopsis and studied plants with different levels of PDV2. Our results suggested that the chloroplast division phenotype in Arabidopsis is sensitive to the level of PDV2, while this is not the case for ARC6. The level of PDV2 protein is reduced sharply in fast-growing leaves, while the level of ARC6 is not. The levels of PDV2 and ARC6 in several other plant species at different developmental stages were also investigated. The results indicated that their expression pattern varies in different species. Thus, PDV2 is an important positive factor of chloroplast division with an apparent dosage effect in Arabidopsis, but this effect for different chloroplast division proteins in different plants may vary.

Growth-arrest-specific protein 2 inhibits cell division in Xenopus embryos.

Directory of Open Access Journals (Sweden)

Tong Zhang

Full Text Available Growth-arrest-specific 2 gene was originally identified in murine fibroblasts under growth arrest conditions. Furthermore, serum stimulation of quiescent, non-dividing cells leads to the down-regulation of gas2 and results in re-entry into the cell cycle. Cytoskeleton rearrangements are critical for cell cycle progression and cell division and the Gas2 protein has been shown to co-localize with actin and microtubules in interphase mammalian cells. Despite these findings, direct evidence supporting a role for Gas2 in the mechanism of cell division has not been reported.To determine whether the Gas2 protein plays a role in cell division, we over-expressed the full-length Gas2 protein and Gas2 truncations containing either the actin-binding CH domain or the tubulin-binding Gas2 domain in Xenopus laevis embryos. We found that both the full-length Gas2 protein and the Gas2 domain, but not the CH domain, inhibited cell division and resulted in multinucleated cells. The observation that Gas2 domain alone can arrest cell division suggests that Gas2 function is mediated by microtubule binding. Gas2 co-localized with microtubules at the cell cortex of Gas2-injected Xenopus embryos using cryo-confocal microscopy and co-sedimented with microtubules in cytoskeleton co-sedimentation assays. To investigate the mechanism of Gas2-induced cell division arrest, we showed, using a wound-induced contractile array assay, that Gas2 stabilized microtubules. Finally, electron microscopy studies demonstrated that Gas2 bundled microtubules into higher-order structures.Our experiments show that Gas2 inhibits cell division in Xenopus embryos. We propose that Gas2 function is mediated by binding and bundling microtubules, leading to cell division arrest.

Z ring as executor of bacterial cell division.

Science.gov (United States)

Dajkovic, Alex; Lutkenhaus, Joe

2006-01-01

It has become apparent that bacteria possess ancestors of the major eukaryotic cytoskeletal proteins. FtsZ, the ancestral homologue of tubulin, assembles into a cytoskeletal structure associated with cell division, designated the Z ring. Formation of the Z ring represents a major point of both spatial and temporal regulation of cell division. Here we discuss findings concerning the structure and the formation of the ring as well as its spatial and temporal regulation.

Biennial report [for] 1978 and 1979, Electronics Division

International Nuclear Information System (INIS)

1980-01-01

The activities of the Electronics Division of the Bhabha Atomic Research Centre, Bombay, during the calendar years 1978-1979 are reported. The Division designed and fabricated electronic equipment and instruments for use in the fields of nuclear science, nuclear reactors, microcomputer hardware and software, health and safety, medicine, chemical analysis and industry. Many of these are described in brief mentioning their special features and in many cases block diagrams are given. (M.G.B.)

77 FR 57007 - Airworthiness Directives; Pratt & Whitney Division Turbofan Engines

Science.gov (United States)

2012-09-17

... Airworthiness Directives; Pratt & Whitney Division Turbofan Engines AGENCY: Federal Aviation Administration (FAA... turbofan engines. That AD currently requires initial and repetitive fluorescent penetrant inspections (FPI... applies to the following Pratt & Whitney Division (Pratt & Whitney) turbofan engines: (1) PW4000-94...

Energy Division annual progress report for period ending September 30, 1991

Energy Technology Data Exchange (ETDEWEB)

Stone, J.N. [ed.

1992-04-01

The Energy Division is one of 17 research divisions at Oak Ridge Laboratory. Its goals and accomplishments are described in this annual progress report for FY 1991. The division`s total expenditures in FY 1991 were $39.1 million. The work is supported by the US Department of Energy, US Department of Defense, many other federal agencies, and some private organizations. Disciplines of the 124 technical staff members include engineering, social sciences, physical and life sciences, and mathematics and statistics. The Energy Division`s programmatic activities focus on three major areas: (1) analysis and assessment, (2) energy conservation technologies, and (3) military transportation systems. Analysis and assessment activities cover energy and resource analysis, the preparation of environmental assessments and impact statements, research on waste management, analysis of emergency preparedness for natural and technological disasters, analysis of the energy and environmental needs of developing countries, technology transfer, and analysis of civilian transportation. Energy conservation technologies include electric power systems, building equipment (thermally activated heat pumps, advanced refrigeration systems, novel cycles), building envelopes (walls, foundations, roofs, attics, and materials), and technical issues for improving energy efficiency in existing buildings. Military transportation systems concentrate on research for sponsors within the US military on improving the efficiency of military deployment, scheduling, and transportation coordination.

Metals and Ceramics Division progress report for period ending December 31, 1993

Energy Technology Data Exchange (ETDEWEB)

Craig, D.F.; Bradley, R.A.; Weir, J.R. Jr.

1994-07-01

This report provides an overview of activities and accomplishsments of the division from October 1992 through December 1993; the division is organized to provide technical support, mainly in the area of high-temperature materials, for technologies being developed by DOE. Activities span the range from basic research to industrial interactions (cooperative research and technology transfer). Sections 1-5 describe the different functional groups (engineering materials, high-temperature materials, materials science, ceramics, nuclear fuel materials). Sect. 6 provides an alternative view of the division in terms of the major programs, most of which cross group lines. Sect. 7 summarizes external interactions including cooperative R and D programs and technology transfer functions. Finally, Sect. 8 briefly describes the division`s involvement in educational activities. Several organizational changes were effected during this period.

Asymmetric cell division of stem cells in the lung and other systems

Directory of Open Access Journals (Sweden)

Mohamed eBerika

2014-07-01

Full Text Available New insights have been added to identification, behavior and cellular properties of embryonic and tissue-specific stem cells over the last few years. The modes of stem cell division, asymmetric versus symmetric, are tightly regulated during development and regeneration. The proper choice of a stem cell to divide asymmetrically or symmetrically has great consequences for development and disease because inappropriate asymmetric division disrupts organ morphogenesis, whereas uncontrolled symmetric division induces tumorigenesis. Therefore, understanding the behavior of lung stem cells could identify innovative solutions for restoring normal morphogenesis and/or regeneration of different organs. In this concise review, we describe recent studies in our laboratory about the mode of division of lung epithelial stem cells. We also compare asymmetric cell division in the lung stem cells with other tissues in different organisms.

Quantum internet using code division multiple access

Science.gov (United States)

Zhang, Jing; Liu, Yu-xi; Özdemir, Şahin Kaya; Wu, Re-Bing; Gao, Feifei; Wang, Xiang-Bin; Yang, Lan; Nori, Franco

2013-01-01

A crucial open problem inS large-scale quantum networks is how to efficiently transmit quantum data among many pairs of users via a common data-transmission medium. We propose a solution by developing a quantum code division multiple access (q-CDMA) approach in which quantum information is chaotically encoded to spread its spectral content, and then decoded via chaos synchronization to separate different sender-receiver pairs. In comparison to other existing approaches, such as frequency division multiple access (FDMA), the proposed q-CDMA can greatly increase the information rates per channel used, especially for very noisy quantum channels. PMID:23860488

Current research in Radiation Biology and Biochemistry Division

International Nuclear Information System (INIS)

Tarachand, U.; Singh, B.B.

1995-01-01

The Radiation Biology and Biochemistry Division, Bhabha Atomic Research Centre, Bombay has been engaged in research in the frontier areas of (i) radiation biology related to tumour therapy and injury caused by free radicals; (ii) molecular basis of diseases of physiological origin; (iii) molecular aspects of chemical carcinogenesis and (iv) structure of genome and genome related functions. The gist of research and development activities carried out in the Division during the last two years are documented

Current research in Radiation Biology and Biochemistry Division

Energy Technology Data Exchange (ETDEWEB)

Tarachand, U; Singh, B B [eds.; Bhabha Atomic Research Centre, Bombay (India). Radiation Biology and Biochemistry Div.

1996-12-31

The Radiation Biology and Biochemistry Division, Bhabha Atomic Research Centre, Bombay has been engaged in research in the frontier areas of (i) radiation biology related to tumour therapy and injury caused by free radicals; (ii) molecular basis of diseases of physiological origin; (iii) molecular aspects of chemical carcinogenesis and (iv) structure of genome and genome related functions. The gist of research and development activities carried out in the Division during the last two years are documented.

Robustness of the division symmetry in Escherichia coli and functional consequences of symmetry breaking

International Nuclear Information System (INIS)

Gupta, Abhishekh; Lloyd-Price, Jason; Oliveira, Samuel M D; Yli-Harja, Olli; Muthukrishnan, Anantha-Barathi; Ribeiro, Andre S

2014-01-01

The morphological symmetry of the division process of Escherichia coli is well-known. Recent studies verified that, in optimal growth conditions, most divisions are symmetric, although there are exceptions. We investigate whether such morphological asymmetries in division introduce functional asymmetries between sister cells, and assess the robustness of the symmetry in division to mild chemical stresses and sub-optimal temperatures. First, we show that the difference in size between daughter cells at birth is positively correlated to the difference between the numbers of fluorescent protein complexes inherited from the parent cell. Next, we show that the degree of symmetry in division observed in optimal conditions is robust to mild acidic shift and to mild oxidative stress, but not to sub-optimal temperatures, in that the variance of the difference between the sizes of sister cells at birth is minimized at 37 °C. This increased variance affects the functionality of the cells in that, at sub-optimal temperatures, larger/smaller cells arising from asymmetric divisions exhibit faster/slower division times than the mean population division time, respectively. On the other hand, cells dividing faster do not do so at the cost of morphological symmetry in division. Finally we show that at suboptimal temperatures the mean distance between the nucleoids increases, explaining the increased variance in division. We conclude that the functionality of E. coli cells is not immune to morphological asymmetries at birth, and that the effectiveness of the mechanism responsible for ensuring the symmetry in division weakens at sub-optimal temperatures. (paper)

Asymmetric cell division and its role in cell fate determination in the ...

Indian Academy of Sciences (India)

Supplementary figure 1. Light micrograph of an asymmetrically dividing T. indica cell at various time intervals. Progress over a 12 hr period, showing that the larger component does not undergo further division. (A) 0 h, cell division at an early stage. (B) 5 h, lower half of cell undergoing further division. (C) 12 h, differentiated ...

The mechanisms of labor division from the perspective of individual optimization

Science.gov (United States)

Zhu, Lirong; Chen, Jiawei; Di, Zengru; Chen, Liujun; Liu, Yan; Stanley, H. Eugene

2017-12-01

Although the tools of complexity research have been applied to the phenomenon of labor division, its underlying mechanisms are still unclear. Researchers have used evolutionary models to study labor division in terms of global optimization, but focusing on individual optimization is a more realistic, real-world approach. We do this by first developing a multi-agent model that takes into account information-sharing and learning-by-doing and by using simulations to demonstrate the emergence of labor division. We then use a master equation method and find that the computational results are consistent with the results of the simulation. Finally we find that the core underlying mechanisms that cause labor division are learning-by-doing, information cost, and random fluctuation.

Long-term survivability of riprap for armoring uranium-mill tailings and covers: a literature review. [203 references

Energy Technology Data Exchange (ETDEWEB)

Lindsey, C.G.; Long, L.W.; Begej, C.W.

1982-06-01

Pacific Northwest Laboratory (PNL) is investigating the use of a rock armoring blanket (riprap) to mitigate wind and water erosion of an earthen radon suppression cover applied to uranium mill tailings. Because the radon suppression cover and the tailings must remain intact for up to 1000 years or longer, the riprap must withstand natural weathering forces. This report is a review of information on rock weathering and riprap durability. Chemical and physical weathering processes, rock characteristics related to durability, climatic conditions affecting the degree and rate of weathering, and testing procedures used to measure weathering susceptibilities have been reviewed. Sampling and testing techniques, as well as analyses of physical and chemical weathering susceptibilities, are necessary to evaluate rock durability. Many potential riprap materials may not be able to survive 1000 years of weathering. Available techniques for durability testing cannot adequately predict rock durability for the 1000-year period because they do not consider the issue of time (i.e., how long must riprap remain stable). This report includes an Appendix, which discusses rock weathering, written by Dr. Richard Jahns of Stanford University.

Biennial activity report of Metallurgy Division for 1989 and 1990

International Nuclear Information System (INIS)

Kamachi Mudali, U.; Muraleedharan, P.; Parameswaran, P.; Swaminathan, K.; Sreedharan, O.M.

1993-01-01

This is the first divisional biennial report of the Metallurgy Division of Indira Gandhi Centre for Atomic Research, for the year 1989-1990, after formation of the Metallurgy Division in September 1988. Major areas of work in the Division relate to aqueous corrosion and localised corrosion, stress corrosion cracking and liquid metal corrosion, high temperature oxidation, thermodynamic studies, physical metallurgy studies for structure-property correlations and failure analyses. The principal materials of studies have been the austenitic stainless steels, the current materials of construction in the Fast Breeder Test Reactor and the candidate materials for the Prototype Fast Breeder Reactor

US Army Armor Reference Data in Three Volumes. Volume I. The Army Division.

Science.gov (United States)

1981-01-01

14 FADIO SET AN/GRC-106 . . . . .. . ........ . .. 1 ACHI EGUN 7.92--M VEH FIXS D. .............. 3 RADIO SET AN/GRC-160 ......... .................. 6...8 RADIAC SET AN/POR-27 ...................................... 1 MAC EGUN CAL .50 19 FLEX FOR CIOUJD aE ................... 8

Environmental Transport Division: 1979 report

Energy Technology Data Exchange (ETDEWEB)

Murphy, C.E. Jr.; Schubert, J.F.; Bowman, W.W.; Adams, S.E.

1980-03-01

During 1979, the Environmental Transport Division (ETD) of the Savannah River Laboratory conducted atmospheric, terrestrial, aquatic, and marine studies, which are described in a series of articles. Separate abstracts were prepared for each. Publications written about the 1979 research are listed at the end of the report.

Environmental Transport Division: 1979 report

International Nuclear Information System (INIS)

Murphy, C.E. Jr.; Schubert, J.F.; Bowman, W.W.; Adams, S.E.

1980-03-01

During 1979, the Environmental Transport Division (ETD) of the Savannah River Laboratory conducted atmospheric, terrestrial, aquatic, and marine studies, which are described in a series of articles. Separate abstracts were prepared for each. Publications written about the 1979 research are listed at the end of the report

78 FR 48466 - Hewlett Packard Company, Printing & Personal System Americas Division, Marketing Services...

Science.gov (United States)

2013-08-08

..., Printing & Personal System Americas Division, Marketing Services, Houston, Texas; Notice of Investigation... Division, Marketing Services, Houston, Texas. On January 25, 2013, the Department issued a Notice of... & Personal System Americas Division, Marketing Services, Houston, Texas) to be filed. Because the later-filed...

Earth Sciences Division annual report 1990

International Nuclear Information System (INIS)

1991-06-01

This Annual Report presents summaries of selected representative research activities grouped according to the principal disciplines of the Earth Sciences Division: Reservoir Engineering and Hydrogeology, Geology and Geochemistry, and Geophysics and Geomechanics. Much of the Division's research deals with the physical and chemical properties and processes in the earth's crust, from the partially saturated, low-temperature near-surface environment to the high-temperature environments characteristic of regions where magmatic-hydrothermal processes are active. Strengths in laboratory and field instrumentation, numerical modeling, and in situ measurement allow study of the transport of mass and heat through geologic media -- studies that now include the appropriate chemical reactions and the hydraulic-mechanical complexities of fractured rock systems. Of particular note are three major Division efforts addressing problems in the discovery and recovery of petroleum, the application of isotope geochemistry to the study of geodynamic processes and earth history, and the development of borehole methods for high-resolution imaging of the subsurface using seismic and electromagnetic waves. In 1989 a major DOE-wide effort was launched in the areas of Environmental Restoration and Waste Management. Many of the methods previously developed for and applied to deeper regions of the earth will in the coming years be turned toward process definition and characterization of the very shallow subsurface, where man-induced contaminants now intrude and where remedial action is required

Interface control document between PUREX/UO3 Plant Transition and Solid Waste Disposal Division

International Nuclear Information System (INIS)

Duncan, D.R.

1994-01-01

This interface control document (ICD) between PUREX/UO 3 Plant Transition (PPT) and Solid Waste Disposal Division (SWD) establishes at a top level the functional responsibilities of each division where interfaces exist between the two divisions. Since the PUREX Transition and Solid Waste Disposal divisions operate autonomously, it is important that each division has a clear understanding of the other division's expectations regarding these interfaces. This ICD primarily deals with solid wastes generated by the PPT. In addition to delineating functional responsibilities, the ICD includes a baseline description of those wastes that will require management as part of the interface between the divisions. The baseline description of wastes includes waste volumes and timing for use in planning the proper waste management capabilities: the primary purpose of this ICD is to ensure defensibility of expected waste stream volumes and Characteristics for future waste management facilities. Waste descriptions must be as complete as-possible to ensure adequate treatment, storage, and disposal capability will exist. The ICD also facilitates integration of existing or planned waste management capabilities of the PUREX. Transition and Solid Waste Disposal divisions. The ICD does not impact or affect the existing processes or procedures for shipping, packaging, or approval for shipping wastes by generators to the Solid Waste Division

Environmental Sciences Division annual progress report for period ending September 30, 1991

Energy Technology Data Exchange (ETDEWEB)

1992-04-01

This progress report summarizes the research and development activities conducted in the Environmental Sciences Division of Oak Ridge National Laboratory during the period October 1, 1990, through September 30, 1991. The report is structured to provide descriptions of current activities and accomplishments in each of the division`s major organizational units. Following the sections describing the organizational units is a section devoted to lists of information necessary to convey the scope of the work in the division. The Environmental Sciences Division (ESD) at Oak Ridge National Laboratory (ORNL) conducts environmental research and analyses associated with both energy technology development and the interactions between people and the environment. The division engages in basic and applied research for a diverse list of sponsors. While the US Department of Energy (DOE) is the primary sponsor ESD staff also perform research for other federal agencies, state agencies, and private industry. The division works collaboratively with federal agencies, universities, and private organizations in achieving its research objectives and hosts a large number of visiting investigators from these organizations. Given the diverse interdisciplinary specialization of its staff, ESD provides technical expertise on complex environmental problems and renders technical leadership for major environmental issues of national and local concern. This progress report highlights many of ESD`s accomplishment in these and other areas in FY 1991.

17 CFR 200.18 - Director of Division of Corporation Finance.

Science.gov (United States)

2010-04-01

... Corporation Finance. 200.18 Section 200.18 Commodity and Securities Exchanges SECURITIES AND EXCHANGE... General Organization § 200.18 Director of Division of Corporation Finance. The Director of the Division of Corporation Finance is responsible to the Commission for the administration of all matters (except those...

77 FR 23637 - Airworthiness Directives; Pratt & Whitney Division Turbofan Engines

Science.gov (United States)

2012-04-20

... Airworthiness Directives; Pratt & Whitney Division Turbofan Engines AGENCY: Federal Aviation Administration (FAA... directive (AD) for certain Pratt & Whitney Division PW4000-94'' and PW4000-100'' turbofan engines having a...-flight engine shutdowns, in certain PW4000-94'' and PW4000-100'' turbofan engines. Pratt & Whitney's...

The marital dynamics of conflict over the division of labor

NARCIS (Netherlands)

Kluwer, E.S.; Heesink, J.A.M.; Van de Vliert, E.

The division of labor as a source of conflict is a concern for many couples. This study goes beyond the mere prediction of the amount of marital conflict by scrutinizing the relationship between spouses' discontent with the division of labor, their conflict interaction patterns, and subsequent

Parenthood and Domestic Division of Labour in Spain, 2002-2010

Directory of Open Access Journals (Sweden)

Xavier Coller

2015-01-01

Full Text Available The literature on the division of domestic work has revealed the influence of the life cycle on family organization. Concretely, the arrival of children seems to have a signifi cant impact on the division of domestic tasks. This article looks at the effect of parenthood in the Spanish case, examining whether couples with children have a more traditional division of work than couples without children, and if so, in what way, and whether there have been changes in this trend over time. For this purpose, we follow the the empirical strategy of Dribe and Stanfors (2009 for the Swedish case, analyzing the time devoted to different activities using data from time use surveys from 2002-2003 and 2009-2010. The results show that couples with children have a more traditional division of labor than couples without children, and that it is also affected by the age of the children. In addition, our fi ndings show this trend was less pronounced in 2009-10.

Asymmetric cell division requires specific mechanisms for adjusting global transcription.

Science.gov (United States)

Mena, Adriana; Medina, Daniel A; García-Martínez, José; Begley, Victoria; Singh, Abhyudai; Chávez, Sebastián; Muñoz-Centeno, Mari C; Pérez-Ortín, José E

2017-12-01

Most cells divide symmetrically into two approximately identical cells. There are many examples, however, of asymmetric cell division that can generate sibling cell size differences. Whereas physical asymmetric division mechanisms and cell fate consequences have been investigated, the specific problem caused by asymmetric division at the transcription level has not yet been addressed. In symmetrically dividing cells the nascent transcription rate increases in parallel to cell volume to compensate it by keeping the actual mRNA synthesis rate constant. This cannot apply to the yeast Saccharomyces cerevisiae, where this mechanism would provoke a never-ending increasing mRNA synthesis rate in smaller daughter cells. We show here that, contrarily to other eukaryotes with symmetric division, budding yeast keeps the nascent transcription rates of its RNA polymerases constant and increases mRNA stability. This control on RNA pol II-dependent transcription rate is obtained by controlling the cellular concentration of this enzyme. © The Author(s) 2017. Published by Oxford University Press on behalf of Nucleic Acids Research.

E-Division semiannual report. Progress report, June 1--December 31, 1977. [Electronics and Instrumentation Division, LASL

Energy Technology Data Exchange (ETDEWEB)

Kelley, P.A. (comp.)

1978-03-01

The status of the programs and projects of the Electronics Division is reported for the period of June through December 1977. The presentation is divided into three sections: Research, Engineering Support, and Technical Services. Each of these sections presents the activities and accomplishments of the corresponding branch within the Division. The primary goal of the Research and Development branch is to advance technology for future applications. The primary goal of the Engineering Support branch is to apply advanced technology to laboratory and material problems. The primary goal of the Technical Services branch is to provide a technical base and support for Laboratory programs. These goals are reflected in this report. Among the subject areas included are the following: radiation detectors, temperature monitoring, electromagnetic probing, Josephson junction switching devices, fiber optics, high-temperature electronics, HVAC systems, microprocessors, fuel cell-powered vehicles, laser fusion.

Segregated integration : recent trends in the Austrian gender division of labor

OpenAIRE

Kreimer, Margareta; Mora, Ricardo

2013-01-01

Using micro data from the Austrian Labor Force Survey, this paper explores how decreases in the gender differential in participation rates together with increasing differentials in the incidence of part-time jobs and stable or rising levels of occupational segregation by gender affect the gender division of labor. To so so, we propose an index for the gender division of labor based on the Mutual Information index. Our main results show that the gender division of labor is very sta...

Solid State Division progress report for period ending March 31, 1997

Energy Technology Data Exchange (ETDEWEB)

Green, P.H.; Hinton, L.W. [eds.

1997-12-01

This report covers research progress in the Solid State Division from April 1, 1995, through March 31, 1997. During this period, the division conducted a broad, interdisciplinary materials research program in support of Department of Energy science and technology missions. The report includes brief summaries of research activities in condensed matter theory, neutron scattering, synthesis and characterization of materials, ion beam and laser processing, and the structure of solids and surfaces. An addendum includes listings of division publications and professional activities.

Intuitions and Undefined Operations: The Cases of Division by Zero.

Science.gov (United States)

Tsamir, Pessia; Sheffer, Ruth; Tirosh, Dina

2000-01-01

Describes a study that explores secondary school students' conceptions of division by zero. Examines whether students identify expressions involving division by zero as undefined or tend to assign them numerical values. Studies students' justifications and analyzes the effects of age and level of achievement in mathematics on students' responses…

Monthly Total Precipitation Observation for Climate Prediction Center (CPC)Forecast Divisions

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — This ASCII dataset contains monthly total precipitation for 102 Forecast Divisions within the conterminous U.S. It is derived from the monthly NCDC climate division...

Monthly Mean Temperature Observation for Climate Prediction Center (CPC) Forecast Divisions

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — This ASCII dataset contains monthly mean temperatures for 102 Forecast Divisions within the conterminous U.S. and is derived from the monthly NCDC climate division...

The Areva Group back-end division - challenges and prospects

International Nuclear Information System (INIS)

2004-06-01

This document presents the Areva Group back-end division challenges and prospects. Areva, a world nuclear industry leader, analyzes in this document, the high-profile mix of complementary activities of the nuclear energy industry, concerning the back-end division the full range of services for the end of the fuel cycle, the fuel cycle back-end markets, the economic and financial associated considerations. (A.L.B.)

ESCRT-III mediated cell division in Sulfolobus acidocaldarius –A reconstitution perspective

Directory of Open Access Journals (Sweden)

Tobias eHärtel

2014-06-01

Full Text Available In the framework of Synthetic Biology, it has become an intriguing question what would be the minimal representation of cell division machinery. Thus, it seems appropriate to compare how cell division is realized in different microorganisms. In particular, the cell division system of Crenarchaeota lacks certain proteins found in most bacteria and Euryarchaeota, such as FtsZ, MreB or the Min system. The Sulfolobaceae family encodes functional homologs of the eukaryotic proteins Vps4 and ESCRT-III. ESCRT-III is essential for several eukaryotic pathways, e.g. budding of intralumenal vesicles (ILVs, or cytokinesis, whereas Vps4 dissociates the ESCRT-III complex from the membrane. CdvA (Cell Division A is required for the recruitment of crenarchaeal ESCRT-III proteins to the membrane at mid-cell. The proteins polymerize and form a smaller structure during constriction. Thus, ESCRT-III mediated cell division in S. acidocaldarius shows functional analogies to the Z ring observed in prokaryotes like E. coli, which has recently begun to be reconstituted in vitro. In this short perspective, we discuss the possibility of building such an in vitro cell division system on basis of archaeal ESCRT-III.

Energy Division annual progress report for period ending September 30, 1981

Energy Technology Data Exchange (ETDEWEB)

1982-05-01

This eighth annual report of the Division covers work done during FY 1981 (October 1, 1980, through September 30, 1981). As with these documents in the past, the format follows approximately the organizational structure of the Energy Division. Chapters 2 through 6 summarize the activities of the sections of the Division: Environmental Impact Section, headed by H.E. Zittel; Regional and Urban Studies Section, R.M. Davis; Economic Analysis Section, R.B. Shelton; Data and Analysis Section, A.S. Loebl; and Efficiency and Renewables Research Section, J.W. Michel. In addition, work on a variety of projects which cut across section lines is reported in Chapter 7, Integrated Programs. These activities are under the supervision of T.J. Wilbanks, Associate Director for the Division. Separate abstracts are included for individual projects.

Energy Division annual progress report for period ending September 30, 1981

International Nuclear Information System (INIS)

1982-05-01

This eighth annual report of the Division covers work done during FY 1981 (October 1, 1980, through September 30, 1981). As with these documents in the past, the format follows approximately the organizational structure of the Energy Division. Chapters 2 through 6 summarize the activities of the sections of the Division: Environmental Impact Section, headed by H.E. Zittel; Regional and Urban Studies Section, R.M. Davis; Economic Analysis Section, R.B. Shelton; Data and Analysis Section, A.S. Loebl; and Efficiency and Renewables Research Section, J.W. Michel. In addition, work on a variety of projects which cut across section lines is reported in Chapter 7, Integrated Programs. These activities are under the supervision of T.J. Wilbanks, Associate Director for the Division. Separate abstracts are included for individual projects

1:N Space Division Switches for Optical Routing, Reconfigurable Interconnections, and Time and Wavelength-Division Switching Applications

National Research Council Canada - National Science Library

Shire, D

1998-01-01

... of time-division multiplexing and demultiplexing operations. Hysteresis in the input-output transfer characteristics of the coupled in-plane lasers and VCSELs also leads to bistable operation over a range of bias conditions...

GREK KOLONİZASYON DÖNEMİ’NDE KARADENİZ’DE ÖNEMLİ BİR GEÇİM KAYNAĞI: KÖLE TİCARETİ

OpenAIRE

EMİR, Osman

2015-01-01

The concept of slavery which first appeared in Hammurabi Laws became an important factor in the world of Greece and Rome. The Greek people began to found colonies around The Black Sea for some economic and political reasons from the 7th century B.C. on. These colonies which were considered as agoras (markets) instead of residential areas developed economic, cultural, political and commercial relations with the people of this region. There wasn’t any slave trade or slave market i...

59th Medical Wing Clinical Research Division Clinical Investigations Program Pathology Poster

Science.gov (United States)

2017-04-28

59 MDW/SGVU SUBJECT: Professional Presentation Approval 1. Your paper, entitled 59th Medical Wing Clinical Research Division Clinical Investigations...Program Pathology Poster presented at/published to For hanging in a hallway of the 591h Medical Wing Clinical Research Division, Bldg 4430 in...Graduate Health Sciences Education student and your department has told you they cannot fund your publication, the 59th Clinical Research Division may