Development of high-efficiency wastes-burning electric power generating technology. Volume 1. Report for fiscal 1999; Kokoritsu haikibutsu hatsuden gijutsu kaihatsu 1999 nendo hokokusho. 1

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This paper summarizes the achievements of developing a technology to generate electric power at high efficiency by using a combustion furnace that uses general wastes and combustible industrial wastes as fuel to generate high-temperature and high-pressure steam under a stabilized condition. In the developmental research of the combustion furnace, discussions were given on single-pass and double-pass type stalker furnaces, an internal circulation type fluidized bed furnace, and an external circulation type fluidized bed furnace, whereas technological prospects were established on any of them as the combustion furnace. In developing corrosion resistant super heater materials, demonstration tests were performed by using a pilot plant, corrosion mechanisms were elucidated, amount of corrosion in steam generating tubes was discussed, and corrosion life of super heaters was estimated. In developing a technology to reduce environmental load, developmental researches were carried out on a method to treat waste gases by using pulse plasma to have established nearly completely a waste gas treatment system technology. In the demonstration test using the pilot plant, the operation has started from February 1998, generating stably the steam conditions of 500 degrees C and 9.8 MPa, and the smooth operation has continued. (NEDO)

Development of high-efficiency wastes-burning electric power generating technology. Volume 2. Report for fiscal 1999; Kokoritsu haikibutsu hatsuden gijutsu kaihatsu 1999 nendo hokokusho. 2

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

In high-efficiency power generation using general wastes and combustible industrial wastes as fuel, development has been performed on a wastes gasifying and melting power generation technology. This technology is capable of suppressing generation of dioxines, recovering slag that can be utilized effectively, and reducing ash volume, by thermally decomposing the wastes and melting combustion ash at elevated temperatures by using thermally decomposed gases. With regard to the evaluation on high temperature corrosiveness of SH materials and the development of a high temperature dust removing system, a steam heater was designed, fabricated, and installed in a model plant, wherein the operation test has been performed for about 1,620 hours. For the technology of dechlorination during a thermal decomposition process, dechlorination rate of 90% was confirmed at 425 degrees C or higher in a demonstration plant. In addition, developments were made on a low temperature denitration device to avoid re-heating of waste gases, a stable wastes supply system to reduce quantity of self-heated melt limiting heat generation, and a waste plastics blowing technology to reduce external fuel charge quantity. Furthermore, a survey was carried out on the trends in wastes electric power generation technologies. (NEDO)

Economical effect of introducing a photovoltaic system on future electric power system; Shorai no denryoku keito eno taiyoko hatsuden system donyu ni yoru keizaiteki eikyo

Energy Technology Data Exchange (ETDEWEB)

Akata, N.; Kenmoku, Y.; Sakakibara, T. [Toyohashi University of Technology, Aichi (Japan); Kawamoto, T. [Shizuoka University, Shizuoka (Japan); Nakagawa, S. [Maizuru National College of Technology, Kyoto (Japan)

1997-11-25

Economic impact of introduction in the future of photovoltaic power generation (PV) systems into the commercial power system is discussed from the electric utilities` point of view. In the discussion, future demand for power is predicted from the demand for power in the base year, and the optimum power source configuration corresponding to the future demand and power generation curve are worked out by use of linear programming. Then, the fixed cost and variable cost are calculated for each of the power source components, and then the expected reduction in cost per unit of power generated is calculated. As the power sources, the hydroelectric, pumped storage, oil-fired, coal-fired, LNG-fired, combined cycle, and atomic technologies are considered. The conclusion is stated below. Upon introduction of PV power equivalent to 10% of the maximum demand power, the maximum power in the service area of Chubu Electric Power Co., Inc., will be reduced by 1.23GW in 2025, and the yearly demand power by 5472GWh. Since PV lowers the peak, an increased number of power sources low in variable cost will be used although such will be low in tracking capability. An increase in power demand will enhance the cost reducing effect of the PV system. 5 refs., 4 figs., 3 tabs.

Research and development of system to utilize photovoltaic energy. Study on the scenario for the diffusion of photovoltaic power generating systems; Taiyoko hatsuden riyo sytem no kenkyu kaihatsu. Taiyoko hatsuden donyu fukyu scenario sakusei no tame no chosa

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the result obtained during fiscal 1994 on a survey to prepare scenario for the diffusion of photovoltaic power generating systems. Introduction target planned with help of a diffusion simulation was verified by calculations using simulation models. The calculations made the following points clear: facility costs and power generation costs for photovoltaic power generation systems, amount of introduced photovoltaic power generation systems, number of facilities introducing photovoltaic power generation systems, policy cost to achieve the target, annual power generation amount, oil substituting effect, carbon dioxide reducing effect, and market sizes. Power generation cost in fiscal 2000 would drop down to 53 yen per kWh in new installation in independent houses and down to 31 yen per kWh in systems used in schools. These reductions are the result of progress in mass production as a result of positively implementing the aiding policies. The required diffusion aiding policies revealed from the simulation results include expansion of subsidy operations for house construction, introduction of the systems into public facilities performed by public organizations, aid to system introduction into private business entities, subsidy to facility investments, and enforcement of power purchase institutions. 3 figs.

Study of installation of PV systems at campus; Campus ni okeru taiyoko hatsuden donyu ni kansuru kenkyu (taiyo denchi nomi wo secchishita baai no yobi kento)

Energy Technology Data Exchange (ETDEWEB)

Tsuboi, N.; Tanaka, H.; Okumiya, M. [Nagoya University, Nagoya (Japan)

1997-11-25

In terms of energy consumption, environmentality and economical efficiency in the case of installing the photovoltaic power system on the rooftop of the university campus, a comparative study was conducted with other power generation systems. As objects to be comparatively studied, selected were the all-electric type centralized space heating/cooling system, cogeneration system, nighttime heat storage system and centralized system with solar cells installed. The panel area of the PV system is 10,000m{sup 2} on the rooftop and 7,000{sup 2} on the outer wall. About data on solar radiation, average values obtained in Nagoya were used. Assessment was made in terms of energy consumption amount at the time of operation, system COP, emission amounts of CO2, NOx and SOx at the time of manufacturing and operation, initial cost, running cost, etc. As a result of the study, an effect of reducing global warming gas was admitted in the PV system. However, the initial cost of the solar cell panel was high, and the life cycle cost of the PV system was lower than other systems. 1 ref., 7 figs., 3 tabs.

Environment-friendly type energy and coordinated community development project. Feasibility study for industrialization of high efficiency waste-fired power generation system using CSD and other wastes; Kankyo chowagata energy community keisei sokushin. Kokoritsu haikibutsu hatsuden (CSD nado haikibutsu riyo) jigyoka FS chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

This report presents the feasibility of enterprise on power generation by thermal recycle and selling power together with volume reduction, de-harming (de-toxification) and stabilization of the shredder dust. Contents of the study include the investigation of generation amount of car shredder dust (CSD) and its properties, trial design of high efficiency power generation facilities, selection of boiler tube materials, incineration test with a melting kiln test plant, disposal and effective use of melted slag and fly ash, and environmental impact assessment. The capacity of waste disposal in the trial design contains 1,140 ton/day of shredder dust, 60 ton/day of waste plastics, sludge and waste paper, and 130 ton/day of waste oil. Melting kiln with secondary combustion chamber was adopted as the incineration type. The high temperature and high pressure waste heat boiler with an extraction condensing turbine was adopted as the waste heat recovery and power generation type. Stable combustion was confirmed from the results using a test plant. According to the consideration of cost and unit cost results for wholesale power supply, if it is postulated that income for waste disposal is 12,000 yen/ton, power generation costs in excess power selling and wholesales are 6.4 yen/kWh and 9.1 yen/kWh, respectively. 67 figs., 48 tabs.

Fiscal 1998 research report. Feasibility survey on offshore wind power generation in Japan; 1998 nendo chosa hokokusho. Nippon ni okeru yojo furyoku hatsuden no donyu kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This survey studied the feasibility of large-scale offshore wind power generation in Japan. Attempt was also made on preparation of outline maps of offshore wind around Japan. The cost of future offshore wind power generation systems is roughly dependent on technical issues and environmental issues. As technical issues, 'installation site,' 'foundation,' 'system interconnection' and 'maintenance/management' were summarized based on applications in Europe. As a result, it was clarified that technical issues can be solved with existing technologies to a certain extent, however, those relate to economical problems closely. The previous environment impact assessments say that wind power generation has no problems on the environmental issues. As relatively strong wind coastal areas, the outline maps of offshore wind point out Western Hokkaido area, Japan Sea area of Tohoku district, Pacific ocean area of the central part of Honshu, Genkai Nada area, Western Kyushu area and Southwest islands area, and suggest that these areas are promising for offshore wind power generation. (NEDO)

Fiscal 1998 research report. Feasibility survey on offshore wind power generation in Japan; 1998 nendo chosa hokokusho. Nippon ni okeru yojo furyoku hatsuden no donyu kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This survey studied the feasibility of large-scale offshore wind power generation in Japan. Attempt was also made on preparation of outline maps of offshore wind around Japan. The cost of future offshore wind power generation systems is roughly dependent on technical issues and environmental issues. As technical issues, 'installation site,' 'foundation,' 'system interconnection' and 'maintenance/management' were summarized based on applications in Europe. As a result, it was clarified that technical issues can be solved with existing technologies to a certain extent, however, those relate to economical problems closely. The previous environment impact assessments say that wind power generation has no problems on the environmental issues. As relatively strong wind coastal areas, the outline maps of offshore wind point out Western Hokkaido area, Japan Sea area of Tohoku district, Pacific ocean area of the central part of Honshu, Genkai Nada area, Western Kyushu area and Southwest islands area, and suggest that these areas are promising for offshore wind power generation. (NEDO)

Fiscal 2000 achievement report on the followup research on high-efficiency refuse-fueled power generation technology development; 2000 nendo kokoritsu haikibutsu hatsuden gijutsu kaihatsu no follow up kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Followup research was conducted using a high-efficiency refuse-fueled power generation pilot plant for interpolating research and development results, improvement on refuse-fueled power generation efficiency, and for introduction and popularization of refuse-fueled power generation. Operation control and safety control were performed in compliance with the pilot plant operation program, when high-temperature high-pressure steam (500 degrees C, 100 atm) was stably generated for approximately 7,600 hours in this fiscal year recording a total of approximately 22,000 hours when counted from the beginning of the verification test. Plant operation data were examined and every part of the furnace was checked and measured while the furnace was at rest, and it was found that the plant satisfied the intended specifications as refuse-fueled power plant facilities. As for its environmental impact, it was confirmed that it fully satisfied the standard values for substances in exhaust gas, which involved soot and dust, sulfur oxides, nitrogen oxides, hydrogen chloride, and dioxins. Dioxins, in particular, were far below the most rigorous legal level of 0.1ng-TEQ/m{sup 3}N. In the test of superheater materials, long-term data covering three years were acquired. (NEDO)

Fiscal 1997 report of the development of high efficiency waste power generation technology. No.1 volume. Element technology development; Kokoritsu haikibutsu hatsuden gijutsu kaihatsu (yoso gijutsu kaihatsu). 1997 nendo hokokusho (daiichi bunsatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Following the previous fiscal year, the technology development was conducted of a high efficiency waste power generation system using general waste as fuel. In the development of high temperature high efficiency combustion furnace, a combustion test on the external circulating fluidized bed incinerator was made to obtain data on formation/decomposition of dioxins. Moreover, a combustion test was conducted using mock refuse, petroleum-derived waste and waste plastics, to confirm stabilized combustion characteristics and low pollution. In the development of a corrosion resistant superheater, made were the stress load high temperature corrosion test, study of intergranular corrosion by elements of impurities, etc. In the development of the environmental load reduction technology, conducted was the conceptional design of pulse plasma exhaust gas disposal equipment corresponding to the actual one. In the verification test in a pilot plant, the pilot plant passed the pre-use inspection and was completed in February 1998. In the study of an optimal total system, discussed were the data on the pilot plant verification test, measuring points, how to arrange them, etc. 2 refs., 88 figs., 50 tabs.

Project to support promotion of forming an environmentally friendly energy community. Survey report on 'a survey on introduction of an RDF electric power generation system utilizing general wastes in the Noto area'; Kankyo chowagata energy community keisei sokushin hojo jigyo. 'Noto chiiki ni okeru ippan haikibutsu riyo RDF hatsuden no donyu ni kansuru chosa' chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

A business feasibility survey was performed on introduction of an RDF electric power generation system utilizing general wastes in the Noto area. Wastes quantity was estimated by accounting for large-sized wastes to be generated newly as a result of enforcement of the container package recycling law, and transfer of non-combustible wastes to incineration. The quantity was estimated to be 84,000 tons annually. Quantities of RDF and heat were calculated from this estimation to be 103 tons per day and 400 lkcal/kg respectively. According to the result of discussing the RDF transportation systems, time-based freight was found advantageous for short distance, and distance freight system for long distance in terms of cost. Discussions for RDF power systems were carried out on an RDF circulation fluid bed furnace plus ash melting furnace, a fluid bed gasification melting furnace, and shaft furnace type gasification melting furnace. In a comprehensive view, it is difficult to distinguish them in terms of merit and demerit. Molten slag was assumed to be re-utilized, but cost for the re-utilization should be considered. According to the result of discussing the business feasibility, it was found difficult to make it profitable by operating the RDF power generation business alone, and wastes incineration charge should be collected. (NEDO)

FY 2001 report on the results of the follow-up study of development of the highly effective waste power generation; 2001 nendo kokoritsu haikibutsu hatsuden gijutsu kaihatsu no follow up gijutsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

For the purpose of safe operation of the highly effective waste power generation pilot plant, confirmation of the performance of corrosion resistant super heater materials under the high temperature corrosion environment, collection of the data on environmental load characteristics in waste incineration, etc., the follow-up study was made. The results were as follows: The pilot plant was able to generate high temperature/high pressure vapor stably for approximately 13,500 hours in FY 2000 and FY 2001 and for approximately 27,800 hours in 4 years since the start of the demonstrative test. The planned performance of plant facilities was fully satisfied, and the performance of environmental load reduction was fully satisfied in standard values of soot/dust, SOx, NOx, hydrogen chloride and dioxins in exhaust gas. Concerning the super heater use developmental material, its durability of 5 years or more was confirmed. It was forecast that by using this, the heightening of temperature/pressure of boiler to 500 degrees C and 100 atmospheric pressure was achieved. Further, the useful information/knowledge on plant design were obtained such as the corrosion prevention technology for waste plant and the forecast of corrosion life of materials. (NEDO)

Waste management in the world; Sekai no haikibutsu shori

Energy Technology Data Exchange (ETDEWEB)

Tanaka, M. [The Institute of Public Health, Tokyo (Japan)

1998-05-15

This paper describes waste management in the world. Richer countries produce more wastes with their contents diversified. Poorer countries produce less wastes, which will not present problems in terms of quantity and quality if individuals will dispose of them properly. Household and kitchen refuses in developing countries are organic in nature, and contain more water. Refuse collectors using such animals as donkeys and horses are still seen. Cases of performing intermediate treatment such as incineration are few, and land reclamation is the main treatment. Neither soil covering nor mud water prevention measures are taken. Smoke stays in air throughout year due to open dumping and open burning, and foul water seeps out. Scavengers (people who collects valuables from dumps) exist, who recover such resources as metals and plastics to make their living. Some of the countries make kitchen refuses into compost. In industrialized countries, ratio of containers and wrappings is high in refuses, which are collected by mechanical recovery vehicles, and carried to incineration facilities and reclamation areas. Securing reclamation areas is difficult. Resource recovery is in a trend of mechanization. Pollution preventive measures are also taken at high levels by means of waste processing. 2 refs., 2 figs., 2 tabs.

Fiscal 1997 report of the development of high efficiency waste power generation technology. No.2 volume. Pilot plant verification test; Kokoritsu haikibutsu hatsuden gijutsu kaihatsu (pilot plant jissho shiken). 1997 nendo hokokusho (daini bunsatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

As to a high efficiency waste power generation system using general waste as fuel, the details of the following were described: design/construction management and operational study of pilot plant, design/manufacture/construction of pilot plant, and study of an optimal total system. Concerning the construction management and operational study, the paper described the application for governmental/official inspection procedures and taking inspection, process management of pilot plant, site patrol, safety management, management of trial run of pilot plant, drawing-up of a verification test plan and test run, etc. Relating to the design/manufacture/construction of pilot plant, an outline of the pilot plant was described. The paper also stated points to be considered in design of furnace structure and boiler structure, points to be considered of the verification test, etc. As to the study of an optimal total system, the following were described: survey of waste gasification/slagging power generation technology, basic study on RDF production process, survey of trends of waste power generation technology in the U.S., etc. 52 refs., 149 figs., 121 tabs.

Space power station. Uchu hatsuden

Energy Technology Data Exchange (ETDEWEB)

Kudo, I. (Electrotechnical Laboratory, Tsukuba (Japan))

1993-02-20

A calculation tells that the amount of electric power the world will use in the future will require 100 to 500 power plants each with an output of 5-GW class. If this conception is true, it is beyond dispute that utilizing nuclear power will constitute a core of the power generation even though the geographical conditions are severe for nuclear power plants. It is also certain that power generation using clean solar energy will play important roles if power supply stability can be achieved. This paper describes plans to develop space solar power generation and space nuclear power generation that can supply power solving problems concerning geographical conditions and power supply stability. The space solar power generation is a system to arrest solar energy on a static orbit. According to a result of discussions in the U.S.A., the plan calls for solar cell sheets spread over the surface of a structure with a size of 5 km [times] 10 km [times] 0.5 km thick, and electric power obtained therefrom is transmitted to a rectenna with a size of 10 km [times] 13 km, a receiving antenna on the ground. The space nuclear power generation will be constructed similarly on a static orbit. Researches on space nuclear reactors have already begun. 10 refs., 8 figs., 1 tab.

Survey for preparing the database for R and D of new engines. Waste power generation, solar heat system, geothermal power generation, clean energy vehicle, coal liquefaction/gasification, and combined systems; Shin energy gijutsu kaihatsu kankei data shu sakusei chosa. Haikibutsu hatsuden, taiyonetsu riyo, chinetsu hatsuden, clean energy jidosha, sekitan ekika gas ka oyobi odanteki tema

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The present developmental conditions and issues of new energies are systematically arranged for effective promotion of their diffusion. One hundred and forty six general waste power generation facilities of 558,000kW are in operation in 1995, and among them 89 facilities supplies 1,080 GWh to power companies. 50 industrial waste power facilities of 247,000kW are in operation. 20,000 solar systems and 180,000 hot water heaters are in operation in 1995. Commercial geothermal power generation facilities of 490,000kW and private ones of 36,000kW are in operation. Introduction of expensive clean energy vehicles is making very slow progress. The pilot study on bituminous coal liquefaction is in promotion mainly by NEDO. The experiment of entrained bed coal gasification in Nakoso was successfully completed, and development of a commercial plant is to be expected. Power rates of 10 power companies were reduced in 1996, and unit purchase prices of surplus power of photovoltaic and wind power generation were also revised. The new menu and unit purchase price were announced in 1996 for surplus power of waste power generation and fuel cell. 67 figs., 284 tabs.

Tidal energy conversion. Renewable energy; 3-3 choseki / choryu hatsuden. II. saisei kano energy ni yoru hatsuden

Energy Technology Data Exchange (ETDEWEB)

Makino, T. [Tobishima Corp., Tokyo (Japan)

1998-10-15

There are not much examples applying tidal energy conversion, but tide and tidal current phenomena can be forecasted so correctly regardless of weather that the applying tidal energy is to be expected in the future. The largest tidal power plant is at Reims in France and install 24 Kaplan turbines each of which outlet power is 10,000kW (rotational direction is reversible) on the breakwater (750m is length). Tidal range at this place being 8.5m on an average, during the period of flowing seawater into the reservoir and on the contrary during the period of discharging seawater to the sea generation is both performed. Though there is no actual result of tidal power plant in Japan, in tidal current power system experimental generators have been installed at Kurushima channel and Naruto channel. Nihon University carried out various kinds of experiment using a Darius turbine (1.6m in dia.) at Kurushima channel and got outlet power of 3kW at the maximum (1983-`88). There are few coasts which have sufficient tide range in Japan, but there are so good many applicable coasts in China and Southeast Asia that the tidal power generation is to be expectatively. 12 refs., 5 figs., 1 tab.

Environment-friendly type energy and coordinated community development project. Feasibility study for industrialization of high efficiency waste-fired power generation system using general RDF; Kankyo chowagata energy community keisei sokushin. Kokoritsu haikibutsu hatsuden (ippainado RDF riyo) jigyoka FS chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The refuse-derived fuel (RDF) has been holding public attention not only as the energy resource of stable high calorific value for local energy development, but also as the effective method for waste treatment. As one of the effective utilization methods for waste treatment, this investigation was conducted to industrialize and establish the RDF power generation system, in which power generation and ash treatment are integrated in Tochigi Prefecture which is located inland. The base supply type was adopted as a way of operation from the menu of the electricity wholesale project of Tokyo Electric Power Co. and its rate of operation is 80 percent a year. Then, the fluidized bed combustion method, a dry exhaust gas treatment method, and continuous electric melting furnaces were decided as the RDF power generation system. According to this system, it is possible to obtain 26 percent gross thermal efficiency by conventional generation facilities. It was estimated that the expenses reduction for 15 years will be 17.6 billion yen compared with the ordinary combustion system. Also, the following effects can be expected; the reduction of CO2 emission, improvement of energy efficiency, and the extension of life of landfills capacity. 36 figs., 51 tabs.

Waste minimization activities in Toyota Motor Corporation; Haikibutsu teigen eno torikumi jokyo

Energy Technology Data Exchange (ETDEWEB)

Taguchi, S.; Yamamoto, N.; Kurai, H. [Toyota Motor Corp., Aichi (Japan)

1998-07-01

Toyota`s waste reduction efforts based on a drive for dealing with the source of waste generation are introduced. For the propulsion of the policy for dealing directly with the origin of waste, it is necessary to convert the existing manufacturing processes that give high priority to product quality and low production cost into environmental impact reduction oriented processes. In particular, conversion of materials into those that are easier to recycle, technology for reducing defective products, technology for the completion of recycling within the process involved, and the simplification of all the processes are mentioned. For the cleaning job in the machining process, a detergent enhanced in oil/water separating capability is developed, and this prolongs doubly the detergent replacement period and decreases the waste liquid to a 1/4 or less of what the conventional method produces. For the handling of foundry sand that is yielded in great quantities, a flow classification system is developed to replace the conventional gravitational classifier, and the reusable coarse-grain sand in the collected dust which occupies approximately 70% of the whole waste is now recovered for reuse. In the vehicle body coating process, a newly-developed robot arm type coating system is developed, which halves the coating waste. 2 refs., 9 figs., 1 tab.

Solar power satellite system; Uchu hatsuden system

Energy Technology Data Exchange (ETDEWEB)

Sasaki, S [Institute of Space and Astronautical Science, Tokyo (Japan)

1995-09-05

The solar power satellite system is a system that converts solar energy into electric energy in the space, transmits power to earth through wireless resort such as microwave and supplies energy of new concept. In order to realize this system it is necessary to have new technologies such as space power transmission at low cost, construction of large space buildings and wireless high power transmission. In this paper, the principles, characteristics and the necessary technology of this system were explained. Besides Japan`s SPS2000 Plan (cooperative research by universities, government agencies and private corporations on the model of solar power satellite) the group of Europe, Russia and the United States has also proposed some ideas concerning the solar power satellite system. As far as the microwave power transmission, which is the key technology for solar power satellite system, is concerned, ground demonstration tests at the level of several tens of kW are discussed in Canada and France. 3 refs., 3 figs.

Promotion of the formation of environmentally friendly energy community (FY 2000). Demonstration of the gas turbine repowering waste combined power generation technology; 2000 nendo kankyo chowagata energy community keisei sokushin seika hokokusho. Gas turbine repowering haikibutsu fukugo hatsuden gijutsu jissho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Demonstrative operation was conducted of the super waste power generation system in which the low temperature steam generated in waste incinerator is raised in temperature using the combustion exhaust gas emitted after the power generation using another gas turbine for conducting the steam turbine power generation with high efficiency. The FY 2000 results were summed up. In the demonstrative operation, operation and data acquisition/analysis were conducted following the previous fiscal year by 25MW class gas turbine repowering waste combined power generation facilities (Takahama power plant). Further, four years after the start of operation, the secular variation was studied by disassembly/inspection of equipment. As a result of the operation, the thermal efficiency was approximately 35%, much higher than the existing waste power generation. It was verified that the power system was maintained by the same maintenance as that of the ordinary power system. Moreover, the important point of this system is that no special corrosion resistant materials are used and that the high-efficiency waste power generation was demonstrated by combining the existing equipment. It can be said that the super waste power system has high qualities for forming energy community as a regionally dispersed stabilized power source. (NEDO)

New energy introduction vision in Chiba Prefecture; Chibaken shin energy donyu vision

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Surveys and discussions were given on establishing a new energy introduction vision in Chiba Prefecture. The basic conception for new energy introduction regarded important the handling of global environment problems, improvement of the global environment, enhancement in energy security, and assurance of the regional performance of disaster prevention. New energy introduction is thought making it possible to create attractive urban spaces, make living environment more agreeable, and promote and breed new industries including the eco-business. Important measures may include the followings: introduction of new and economic energies in multiple ways for individual buildings and facilities, development of environment symbiotic cities utilizing new energies, improvement of region symbiotic cities in industrial zones, effective utilization of energies from wide-area refuses and wastes, establishment of an urban type cleaning plant that utilizes effectively energies from general wastes, new energy utilization in coordination with agricultural activities, utilization of new energies in fishery industry areas, and expansion in use of clean energy fueled automobiles including natural gas fueled automobiles. (NEDO)

Fiscal 1997 report on the survey for a data book on new energy technology development. Waste power generation, solar energy utilization. geothermal power generation, clean energy vehicles, coal liquefaction/gasification, and traverse themes; 1997 nendo chosa hokokusho. Shin energy gijutsu kaihatsu kankei data shu sakusei chosa (haikibutsu hatsuden, taiyonetsu riyo, chinetsu hatsuden, clean energy jidosha, sekitan ekika gas ka oyobi odanteki theme)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper collected and arranged data on new energy technology. As to the waste power generation, in terms of general waste, 161 places have power generation facilities, 657,000 kW in output, as of the end of FY 1996. Out of them, 100 facilities (scale of output: 555,000 kW) are selling power. In terms of industrial waste, 53 places (209,000 kW) have power generation facilities. The output will be 2 million kW in FY 2000. In relation to the solar energy utilization, the number of solar systems introduced in FY 1996 is 25,000, that of water heating appliances produced in FY 1996 is 170,000. Geothermal power of 494,000 kW and 37,000 kW was introduced for electric power industry use and private use, respectively. Clean energy vehicles have not been so much spread, but the hybrid car was put on sale in 1997. Concerning the coal liquefaction, the R and D were made at a pilot plant of NEDOL process, and operation started in 1997. As to the coal gasification, investigational study and element study on the demonstration plant are being conducted in FY 1997 and 1998, making use of the research results obtained from the existing pilot plant of coal gasification combined power generation

Waste treatment of ships. Change in understanding of wastes and trend of waste treatment systems; Senjo no haikibutsu shori. 1. Haikibutsu ni taisuru ninshiki no henka to shori hoshiki no doko

Energy Technology Data Exchange (ETDEWEB)

Inatomi, M. [Hitachi Zosen Corp., Osaka (Japan)

1996-07-25

This paper explains treatment of wastes produced in ships. Wastes produced in ships should be essentially treated on ships. Since storage and transport of difficult-to-treat wastes to harbor for land treatment is expensive, wastes produced in ships are treated on ships as much as possible. Combustibles such as waste oil, plastics, paper and wood fiber waste are treated by incinerator. Food waste is dumped into the sea after crushing by disposer. Excrement and urine are dumped into the sea through a waste water treatment plant. Oil content in oily bilge is burned after heating and vapor separation. Food waste is temporarily stored in ships because its dumping along the coast and into harbor is impossible. Kitchen refuse decomposer utilizing bacteria was proposed for ships. Press for used cans and crushing/thermal compaction/storage equipment for plastics were also put on the market. The primary regulation on diesel engine exhaust gas may be cleared by improvement of engine bodies. 1 ref., 1 fig., 1 tab.

Generation by heated rock. Technology for hot dry rock geothermal power; Yakeishi ni mizu de hatsuden. Koon gantai hatsuden no gijutsu

Energy Technology Data Exchange (ETDEWEB)

Hori, Y. [Central Research Inst. of Electric Power Industry, Tokyo (Japan)

1995-06-15

Japan is one of the most distinguished volcanic country in the world and about 8% of the active volcanos of the world are distributed in Japan. This kind of a large quantity and natural energy resource near us are used as hot springs in the whole country and as for electricity in 10 geothermal power stations. In future, if this enormous underground geothermal energy could be utilized safely and economically by using new power generation system like hot dry rock geothermal power generation (HDR), it may contribute a little to the 21st century`s energy problem of Japan. Central Research Inst. of Electric Power Industry has installed `Okachi HDR testing ground` in Okachi-machi of Akita Ken, and is carrying out experiments since 1989. Hot dry rock geothermal power generation is a method in which water is injected to the hot dry rock and the thermal energy is recovered that the natural rock bed is used as a boiler. However, development of many new technologies is necessary to bring this system in practical use. 9 refs., 5 figs., 1 tab.

New energy introduction guidebook for Chugoku area; Shin energy donyu guidebook. Chugoku chiiki

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-05

A guidebook was edited for the purpose of assisting introduction of new energies. Sections consist of Section 1, new energies available in the Chugoku area; Section 2, procedure for new energy introduction; Section 3, assistance institutions by energy; and Section 4, the status of new energy introduction in the Chugoku area, the future introduction targets, and referential materials. Section 1, upon defining the new energies, summarized features of photovoltaic power generation, solar heat utilization, wind power generation, wastes power generation, cogeneration, fuel cells, clean energy fueled automobiles, and introduction records up to the year 2000. Section 2 summarizes the general roles of local governments in the introduction, processing procedures for individual programs, related regulations, and summary of the assistance institutions. Section 3 puts into order the assistance institutions by energy. Section 4 summarizes precautions, targets and records in introduction by each new energy. The referential materials include a list of the Japanese assistance institutions, and subsidy institutions related to new energies for local governments in the Chugoku area. (NEDO)

Feasibility study on the introduction of hybrid buses; Hybrid bus donyu kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The purpose of this research is to design pilot projects for introducing hybrid buses into the public transportation sector. This research also covers contents regarding hybrid buses with a trolley-collector motor and a diesel engine, to identify technical and economical problems and to analyze cost beneficiation using hybrid buses. The trolley parallel hybrid system has been employed for the feasibility study. This system has abundant operation results in Europe and the USA. Its battery is small or is not necessary, and the maintenance cost is also low. As a result of the feasibility study, reduction effects of CO2 emission were found out. When the CO2 generation at the power plant is not counted, the reduction effect was estimated to be 32% compared with the CO2 emission from diesel buses. When the CO2 generation at the power plant is considered, it was estimated to be 18%. The cost beneficiation was investigated for the cases of the transportations using trolley system surrounding a medium-scale terminal among large-scale housing development, tourist resort, and stations. The annual income is estimated to be larger than the annual payment in each case. It was found that the hybrid bus is economically established. 17 refs., 48 figs., 41 tabs.

Generation characteristics of photovoltaic power generation equipment at TEPCO R and D center; Gijutsu kaihatsu center taiyoko hatsuden setsubi no hatsuden tokusei

Energy Technology Data Exchange (ETDEWEB)

Amano, K; Natori, K [Tokyo Electric Power Co. Inc., Tokyo (Japan)

1997-11-25

Solar battery arrays are installed at different tilt angles for actual measurement in an experiment conducted by TEPCO (Tokyo Electric Power Company, Inc.) Research and Development Center for the examination of their power generation characteristics. Arrays of polycrystalline silicon solar battery modules are positioned facing a direction +7 degrees swung from the south on the Center rooftop and verandah, and they are installed at tilt angles of 0, 30, 60, and 90 degrees. An analysis of system characteristics is conducted, and findings mentioned below are obtained. In fiscal 1996, the highest utilization factor of a yearly average of 11.3% is attained with the ones tilted at 30 degrees. As for the utilization factors at the other angles, they are 10.2% at 60 degrees, 8.8% at 0 degrees, and 8.0% at 90 degrees. The integrated design coefficient remains approximately constant irrespective of the different tilt angles of 0, 30, and 60 degrees. The overall design coefficient of the 90 degree-tilted array installed on the verandah is found to be 0.75, which is higher than those exhibited by the others. Appropriate routes of wirings for modules should be worked out to avoid the ill effect of the shadows of steel towers. 2 refs., 11 figs.

Report on development of high-efficiency wastes power generation technology in fiscal 1998. 1. Development of component technology, and demonstration test of a pilot plant; 1998 nendo kokoritsu haikibutsu hatsuden gijutsu kaihatsu seika hokokusho. Yoso gijutsu kaihatsu (pilot plant jissho shiken) (dai 1 bunsatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

A technology is developed to perform high-efficiency power generation by generating high-temperature and high-pressure steam stably by burning general wastes and combustible industrial wastes as fuel. This paper describes summary of the achievements in fiscal 1998. Corrosion tests were performed on over-heater materials under steam condition of 500 degrees C and 100 kg/cm{sup 2} by using a hot model. It was verified by the tests that the corrosion environment around an external heat exchanger is milder than that with an external stack. A circulation fluid bed was simulated from operation data, and a prospect was obtained on steam conditions required for the high-efficiency power generation. In order to elucidate the corrosion mechanism, discussions were given on deposited ash properties, corrosion characteristics and stress. Elucidation was made on a discharge chamber structure most suitable for removing dioxins and NOx by using a waste gas treatment process that uses plasma generated by discharge. A concept design was made. The economic effect of the system is equivalent to that of the activated carbon blow-in process, whereas a waste gas treatment system was nearly completed. As a result of the pilot plant test, the power generation efficiency is estimated to be 30% in a scale of 1200 tons per 24 hours. A demonstration test revealed that dioxin emission was far below the regulation value. An optimal system was also discussed. (NEDO)

Space photovoltaic power generation. Uchu taiyo hatsuden ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Kudo, I [Electrotechnical Laboratory, Tsukuba (Japan)

1993-07-20

Introduction is made of space photovoltaic power generation which is the ultimate clean energy source. This is a system to obtain electric energy from the solar cells placed on a geostatic orbit and transmit the power onto the earth by microwave. The US formulates a plan of placing 60[times]5GW power generation satellites to obtain 300GW power on the earth in 2000. As for the scale of space structure, the array of solar cells is dimensionally 10km[times]5km and the power transmitting antenna is 1km in diameter. The electric energy is amplified to microwave and power-transmitted by wireless onto the earth. The ground rectenna which receives it is dimensionally 10km[times]13km. The biggest difficulty consists in transportation of construction materials onto the orbit. In Japan, activity comprises three matters, which are research committee organized three years ago by the Agency of Industrial Science and technology, 10MW class model conceptually designed by the Institute of Space and Astronautical Science, and experiment conducted by Kyoto University on the power transmission by wireless. Pertaining to the research on the space power generation, the following two points are judged still unclarified: Reason for which the electric power companies did not apply the power transmission by wireless regarded as high in transmission efficiency. Influence of the microwave on the ionosphere and biosystem. 7 refs., 4 figs.

Guidebook for introduction of snow/ice cool energy; Seppyo reinetsu energy donyu guide book

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

For the purpose of contributing to the promotion of introduction of snow/ice cool energy in cold snowing areas, investigational study was made such as analysis of samples of introduction of snow/ice cool energy and effects. In the survey, for three kinds of the snow/ice cool energy system, that is, snow air-conditioning/refrigerating system, ice shelter system and artificial frozen soil system (heat pipe), each of the samples of introduction was outlined, and the effect of introduction by system was analyzed. As to the evaluation of economical efficiency, constructed were 12 kinds of the snow/ice cool energy spread type model system by the demand facilities including distribution facilities of perishable foods and shopping centers, hospitals and multiple dwelling houses, commercial/residential facilities such as office buildings, and industrial facilities such as food factories. These was comparatively studied with the electric air-conditioning system. As a result, it was made clear that the total cost was approximately a half times as high as that of the electric air-conditioning system, but the system had great incentive effect, supported by subsidies for the initial investment. (NEDO)

Fiscal 1997 survey report. Basic survey on trends of waste use type production facilities and waste fuel production facilities; 1997 nendo chosa hokokusho. Haikibutsu riyogata seizo shisetsu oyobi haikibutsu nenryo seizo shisetsu doko kiso chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This survey was made to obtain the basic data for future spread and promotion of No.6 type (waste use type production facilities) and No.7 type (waste fuel production facilities) which were added to the objects having been subsidized since fiscal 1997 under `the environmental harmony type energy community project.` In the former, the kiln in the cement industry and the blast furnace in the steel industry can be extremely large places to receive waste plastic since the facilities are distributed in every area and the treatment capacity is large. However, the effective collection, transportation and sorting of large quantity of waste plastic, especially the problem of removal of vinyl chloride, is a big bottleneck. As to the use of waste plastic using gasification technology, there are no actual results on the commercial basis. That is, however, appropriate for treatment of the waste difficult in treatment, and can be expected of the usage in the chemical industry. In the latter, in the facilities using industrial waste raw materials as fuel, solidification and liquefaction are both operated on a commercial basis. In relation to the solidification and use as fuel of general waste, the treatment of combustion ash is preventing the expansion of use of waste in the industrial field because of a large quantity of chlorine included in the products. 92 refs., 54 figs., 35 tabs.

Environment-friendly type energy and coordinated community development project. Feasibility study for industrialization of high efficiency waste-fired power generation system (industrial refuse derived fuel and gas turbine combined type); Kankyo chowagata energy community keisei sokushin. Kokoritsu haikibutsu hatsuden (sangyo RDF GT fukugogata) jigyoka FS chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

High efficiency power generation, which is useful for promoting the environment-friendly type energy and coordinated community, is investigated by combining a steam turbine power generation system using the PS-RDF (paper sludge-refuse derived fuel) and a gas turbine (GT) combined cycle. Industrialization plan for processing PS in low cost has been made to ensure the profitability by participating the wholesale power supply under the law of electric power industry. This combined system is similar to the so-called super power generation using municipal garbage, but the lower temperature of steam from GT waste heat boilers (WHB) is super-heated by the flue gas from RDF boiler, which is called advanced power generation system (A.S.S.). The total power generation capacity is 149,000 kW, which consists of three 35,000 kW units of GT and one 44,000 kW unit of steam turbine. When comparing the combined system (A.S.S.) and usual one with the independent installation of the RDF steam power generation system and a GT combined cycle, the A.S.S. provides the repowering efficiency of 7,600 kW output with exactly the same quantity of fuel input as usual one. 71 figs., 31 tabs.

Industry brief letter; Oman LNG, Indo no hatsuden mukeni kyokyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-02-01

Oman LNG (OLNG), invested by Mitui Bussan, Mitsubishi Trading and Itochu Trading, concluded a supply contract of liquefied natural gas with a private power supply enterprise of India. Contract period is 20 years, and supplies 1.6 million ton LNG per year from the fourth quarter of 2001. This is the third contract case following to Korea Gas of Korea and Osaka Gas of Japan. OLNG will establish annual production 6.6 million system by the end of 1999. With this contract, almost all LNG production will be ensured to be sold by long term contracts. (translated by NEDO)

FY 1998 survey report. Survey to prepare a data book related to new energy technology development (Trends on the waste power generation, solar heat utilization, geothermal power generation, clean energy cars, coal liquefaction/coal gasification and new energy); 1998 nendo chosa hokokusho. Shin energy gijutsu kaihatsu kankei data shu sakusei chosa (haikibutsu hatsuden, taiyonetsu riyo, chinetsu hatsuden, clean energy, jidosha, sekitan ekika gas ka oyobi shin energy kanren doko)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Together with the progress of technology development, policies for the introduction/promotion of new energy technology are being developed such as promotion of the commercialization development, revision of the law system, and expansion of the subsidy system for promotion. To push the introduction/promotion forward more effectively, it is necessary to arrange various kinds of data comprehensively/systematically and to make them the basic data for contribution to the spread/education. As to the six fields of the waste power generation, solar heat utilization, geothermal power generation, clean energy cars, coal liquefaction, and coal gasification of the technology fields of new energy, this report collected/arranged the data made public recently in terms mainly of the following: trends of the introduction in Japan and abroad, policy/law/subsidy system in Japan and abroad, cost, system outline, basic terms, a list of the main affiliated companies and groups, and the nation's outlook for energy introduction and policies of each new energy technology in Japan and abroad, and the trends. Moreover, characteristics by field were described of the state of the commercialization/introduction of new energy technology. (NEDO)

Effect of groupware introduction on office works; Groupware donyu no white color gyomu e ataeru eikyo

Energy Technology Data Exchange (ETDEWEB)

Baba, K. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

1996-05-01

Investments for information systems in Japanese firms have been shifting from those for main frame systems to PC, LAN and groupware systems. Described herein are effects of groupware introduction on office works, and efficient introduction and practical application of these systems. The groupware functions are divided into information sharing, analyzing, integrating and coordinating functions, and changed information transmission as a result of practical application of each function has been followed by literature and questionnaire surveys on experiences at advanced enterprises. The results indicate that the changes are represented by 6 patterns, from replacement of information media to changes in working styles. The major productivity-related effects brought by introduction of these systems are decreased document volumes and improved skills of employees. The notable effects on office works are improved efficiency resulting from allotting one personal computer to each employee and from introduction of E-mail systems which solve problems involved in telephone communication. 15 refs., 11 figs., 10 tabs.

Programs for promoting new energy introduction into Wakkanai City; Wakkanaishi shin energy donyu sokushin keikaku keikakusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The average temperature in the summer season at Wakkanai is 19 degrees C, and below zero degrees C in the winter season. Solar radiation duration is shorter in November through February due partly to the presence of snow. In terms of total solar radiation amount, the city occupies a middling position in the whole Hokkaido island. As for the force of the wind, a daily maximum wind velocity of 10m/s or stronger occur on 8 to 10 days every month in the period October through May. As projects for promoting new energy introduction, the below-named ones are chosen and subjected to examination for feasibility. They are a wind power generation system for a water purification plant; a district heating system utilizing cogeneration at the city middle sector; a hybrid system of methane fermentation and wind power generation for a public stock-rearing farm; a hybrid system of cogeneration and photovoltaic power generation for Fujimi district accommodation facilities; and photovoltaic power generation as a clean energy introduction system for a general gymnastic hall of Wakkanai City. Since the above-named subjects are all excellent in economy and environmentally-friendliness, it is suggested that efforts be exerted to realize them. (NEDO)

Resources, environment and solid waste management; Shigen {center{underscore}dot} kankyo mondai to haikibutsu shori no tenkai

Energy Technology Data Exchange (ETDEWEB)

Takeda, Nobuo [Kyoto University, Kyoto (Japan). Department of Environmental Engineering

1999-09-20

Solid waste management should be considered in close relation to conservation of energy and resources. The history and situation of solid waste management in Japan is outlined and the new concept of waste management is discussed for sustainable development. (author)

Indices for planning wind power generation; Furyoku hatsuden no keikaku shihyo

Energy Technology Data Exchange (ETDEWEB)

Takeuchi, H

1997-11-25

Outlined herein are status of wind power generation development, indices for planning development, and actual development results. At present, wind power generates electric power of 6,781MW worldwide. USA has been rapidly developing wind power generation since enactment of the PURPA law, and accounted for 25% of the world output in the past. However, the county is recently unseated from the world top position by Germany, which has been extensively developing wind power generation since enactment of the EFL law to reach 1,799MW. In Japan, electric power companies, local governments and public institutions have been positively introducing wind mills since 1992, when Tohoku Electric Power Co. built Ryuhi Wind Park, now generating a total power of 15MW by 64 units located at 33 different points. According to the surveys by NEDO on wind conditions, there are a number of districts suited for wind mills in Hokkaido, Tohoku, Okinawa and sea areas in Honshu. The indices described herein for planning wind power generation include rotor diameter, tower height, speed of rotation, weight, power to be generated, utilization and service factors, noise level, and investment and running costs. In the present state of the development of wind power generation in Japan, development points are 33, generated ouptut 15,097kW and units 64. 14 figs.

FY 2000 report on the survey of the project to promote and support the formation of the environmentally friendly energy community. Feasibility study on the waste utilization high efficiency power generation project; Kankyo chowagata energy community keisei sokushin jigyo chosa hokokusho. Haikibutsu riyo kokoritsu hatsuden jigyo ni kakawaru FS chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

An investigational study was conducted on energy recovery (power generation) in disposal of industrial waste. The capacity of power generation facilities in incineration processing of industrial waste reached approximately 200,000kW (50 facilities) in the total nationwide. The incineration-processed waste is mainly chips of wood, waste tire and bagasse. Almost all the electric power is for non-utility use, and there are no examples of selling it outside. In the metropolitan area, there is only one example of the industrial waste incineration power generation in Tochigi prefecture. This is because there are extremely very few enterprises which are sources producing the waste as target. However, if the industrial waste market is targeted, there is a future. The industrial waste has a lot of disadvantages as power generation use fuel because of its diversification, but the use of it as fuel is technically easier than the use of the general waste as RDF. Accordingly, it can be used for power generation with no need of special technology or facilities. When picking up facilities with a potentiality of high efficiency power generation from the existing incinerators in operation of persons in charge of industrial waste processing, approximately 125,000 kW can be obtained only from remodeling of the existing facilities. (NEDO)

Development of large scale wind energy conservation system. Development of large scale wind energy conversion system; Ogata furyoku hatsuden system no kaihatsu. Ogata furyoku hatsuden system no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

Described herein are the results of the FY1994 research program for development of large scale wind energy conversion system. The study on technological development of key components evaluates performance of, and confirms reliability and applicability of, hydraulic systems centered by those equipped with variable pitch mechanisms and electrohydraulic servo valves that control them. The study on blade conducts fatigue and crack-propagation tests, which show that the blades developed have high strength. The study on speed-increasing gear conducts load tests, confirming the effects of reducing vibration and noise by modification of the gear teeth. The study on NACELLE cover conducts vibration tests to confirm its vibration characteristics, and analyzes three-dimensional vibration by the finite element method. Some components for a 500kW commercial wind mill are fabricated, including rotor heads, variable pitch mechanisms, speed-increasing gears, YAW systems, and hydraulic control systems. The others fabricated include a remote supervisory control system for maintenance, system to integrate the wind mill into a power system, and electrical control devices in which site conditions, such as atmospheric temperature and lightening, are taken into consideration.

Plan to promote new energy introduction in Niigata Prefecture area; Niigataken chiiki shin energy donyu suishin keikaku

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The 'Plan to promote new energy introduction in Niigata Prefecture area' was established to leave the conditions that everybody can live with affluence and comfort in the next generation. The plan lasts for ten years until 2010. Upon identifying the district characteristics of Niigata Prefecture, and based on the results of investigations on new energy existence quantity, utilization possibility thereof, and consciousness of residents of the prefecture, considerations were given that the plan shows the basic policy to promote proliferation of the new energies, and serves as the guideline for practical implementation. The plan document is composed of the following four items: 1) the foreword, 2) the current status of energies, 3) new energies expected of introduction, and 4) basic measures. The energy consumption was estimated to increase to 1.345 times that of fiscal 1990 in the year 2010, the increase being mainly in consumer and household use. The targeted quantity for new energy introduction was set to 90,000 kl annually as converted to petroleum. Expected new energy applications would include photovoltaic power generation, snow energy and solar heat utilization, and cogeneration utilizing natural gas. (NEDO)

Experimental study of water permeability in waste disposal facilities; Haikibutsu shori shisetsu no shisuisei ni kansuru jikkenteki kenkyu

Energy Technology Data Exchange (ETDEWEB)

Konishi, M; Shiraishi, H; Terada, M [Okumura Corp., Osaka (Japan)

1995-08-22

A cement-based filler is one of the back filling materials used in radioactive wastes disposal facilities. This paper describes fundamental tests performed on a filling material as to its filling performance, water permeation characteristics, and adsorption property to cerium by using the normal cement mortar (SM) that uses the water-to-cement ratio of 40% and the silica fume mortar (SFM). Furthermore, model wastes were fabricated by using a filling mortar of about 1 m{sup 3} and a 200-liter drum, which were used for tests on the filling and water cut-off performances. The result of the fundamental tests revealed the following matters: all of the materials show good filling performance and adsorbability when an adequate amount of high-performance water reducing agent is mixed; and the diffusion coefficient of the SFM is less than one tenth of that for the SM, showing high water cut-off effect. It was made clear from the tests using simulated test pieces that the Lugeon test value and water permeation coefficient of the SFM is less than half of that for the SM, and high water cut-off effect can be obtained by using the SFM. 11 refs., 8 figs., 4 tabs.

NEDO Forum 2000. New energy and energy conservation introducing and proliferating project session (toward promotion of introducing new energies and energy conservation); Shin'ene shoene donyu fukyu jigyo session. Shin'ene shoene no donyu sokushin ni mukete

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-09-01

The following themes were presented at this session: (1) the history and roles of the NEDO's introduction and promotion projects, (2) expectation and prospects to introduction and promotion of new energy and energy conservation technologies, (3) energy innovation in houses and buildings actively using new energies and energy conservation means, (4) works on introducing new energies by using the private finance initiative (PFI), and (5) the last resort for energy conservation promoting measures in the industrial domain (high-performance industrial furnace technologies). In Item 3, design cases intended for sustainable buildings were introduced. In Item 4, the PFI is explained as a means to use as much fund and management know-how in private sectors as possible in improving the social capitals and providing high-quality public services. In Japan, the PFI promotion law was established in July 1999 (the law concerning promotion of improvements in public facilities by utilizing funds in private sectors). Introductions are given on the wide area wastes disposal project in Kimitsu Area, the PFI model project for power generation of everyday use at Kanamachi Water Purification Plant of the Tokyo Metropolitan Water Supply Bureau, and the Omuta RDF power generation project. In Item 5, descriptions are given on a new high-performance industrial furnace using the combustion mechanism of 'high-temperature air combustion' created from preheated air at temperatures higher than spontaneous combustion temperature. (NEDO)

Development of solar power generator system; Taiyoko netsufukugo hatsuden system no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Kisara, K; Kumagai, T; Niino, M; Chen, L; Eguchi, K [National Aerospace Laboratory, Tokyo (Japan)

1997-11-25

Described herein is a new hybrid solar power generator system, in which solar energy is separated into the light and heat components by a wavelength-selective filter before being directly converted into electric power, the former for the amorphous solar cell (ASC) unit and the latter for the thermoelectric unit. These units complement with each other to enhance overall efficiency. The ASC unit should have a higher efficiency when it works on the light component, because the heat (infrared) component increases cell temperature and decreases its output. For the ASC unit, the effects of the filter have been tested. The thermoelectric unit, generating power by the Seebeck effect, should have a higher efficiency, if heat flux passing through the unit can be increased, because of increased temperature differential, to which voltage produced increases proportionally. For the thermoelectric unit, heat is collected by a parabolic mirror unit from sunbeams received by a heliostat. Characteristics of these units are grasped almost as expected by the tests. 4 refs., 11 figs., 1 tab.

Simulation of stand alone PV systems; Dokuritsugata taiyoko hatsuden system no simulation

Energy Technology Data Exchange (ETDEWEB)

Tsuda, I.; Sakuta, K. [Electrotechnical Laboratory, Tsukuba (Japan); Oshiro, T. [Japan Quality Assurance Organization, Tokyo (Japan); Kurokawa, K. [Tokyo University of Agriculture and Technology, Tokyo (Japan)

1997-11-25

Studies are performed to develop a simulation program for a stand-alone photovoltaic power generation system equipped with a lead acid battery. In this stand-alone photovoltaic power generation system, the load is connected in shunt with the solar cell array output through the intermediary of a lead acid battery and inverter. The program is a model in which the solar cell model is built taking parallel resistance into account, and the temperature-dependence of the constants is described using approximations experimentally obtained by Solar Techno Center of JQA (Japan Quality Assurance Organization), Hamamatsu. Insolation data for the model is described using METPV compiled by Japan Weather Association, and load data is described using data actually measured at Shizuoka. This program is compared with the data of operation at Hamamatsu, and the result is almost satisfactory. Simulations are conducted at five typical locations in Japan using this program, and it is found that the array load matching correction factor is dependent on seasonal changes rather than locality, that the battery contribution rate does not change much throughout the year, and that it is not dependent on locality. 5 refs., 7 figs., 3 tabs.

Simulation of stand alone PV system; Dokuritsugata taiyoko hatsuden system no simulation

Energy Technology Data Exchange (ETDEWEB)

Kondo, H; Ogawa, H; Sekii, Y [Chiba Institute of Technology, Chiba (Japan); Tsuda, I; Nozaki, K [Electrotechnical Laboratory, Tsukuba (Japan); Kurokawa, K [Tokyo University of Agriculture and Technology, Tokyo (Japan)

1996-10-27

In order to evaluate the simulation results of a photovoltaic power generation system, an operation simulation was carried out using the actual measured data of a stand alone PV system in Miyakojima, Okinawa Prefecture, so as to make a comparison with the actual operation data. The electric power was supplied to 250 houses and primary/junior high schools in the surrounding villages, which had an average demand load of approximately 90kw and the maximum of approximately 200kw. The power was supplied through the PV power generation in the duration of the sunshine, with an excess power charged in storage batteries and then supplied from the batteries at night. The array capacity was made 750kWp, the output current and storage batteries being characteristic type with an actual efficiency curve used for the inverter. The weather data used were the actual inclined insolation quantity and the outside air temperature data for a period of one month of November. The power charged in excess of 100% in the batteries was termed as an overflow power. With the charging condition 30% or less, a diesel generator was run for a rated operation for one hour, the power of which was termed as a backup power. As a result, the simulation was found nearly in agreement with the actual measurements. 5 refs., 7 figs., 2 tabs.

Fiscal 1999 edition. Guidebook for introducing new energies in Kinki District; Kinki chiiki shin energy donyu guide book

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-09-01

The captioned guidebook is composed of the following subjects: (1) the current status and problems of new energies (the energy status and the current status of new energies in Japan, and approaches to new energies in Japan); (2) the status of introduction and works in Kinki District (the outline of introduction and works in Kinki District on photovoltaic electric power generation, solar heat utilization, wind power generation, wastes power generation, clean energy fueled automobiles, cogeneration, fuel cells, unused energies, and other reproducible energies); (3) NEDO related supportive institutions (new energy introduction promotion projects by NEDO, and the outline of different supportive institutions); (4) new energy introduction flow (total flow leading to the introduction, and introduction flow by new energies); (5) the grand new energy prize in Kinki District (what is the grand new energy prize? and cases of prizes awarded in Kinki District); (6) new energy related supportive institutions (a list of the related institutions, and the outline of different supportive institutions); and (7) new energy consultation windows and contacts (consultation windows and contacts for general new energy aspects and the government related supportive institutions, and consultation windows by new energies). The grand new energy prize is awarded by New Energy Foundation as the 'institution for public recognition of new energy devices of the 21st century type'. (NEDO)

Fiscal 1999 edition. Guidebook for introducing new energies in Kinki District; Kinki chiiki shin energy donyu guide book

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-09-01

The captioned guidebook is composed of the following subjects: (1) the current status and problems of new energies (the energy status and the current status of new energies in Japan, and approaches to new energies in Japan); (2) the status of introduction and works in Kinki District (the outline of introduction and works in Kinki District on photovoltaic electric power generation, solar heat utilization, wind power generation, wastes power generation, clean energy fueled automobiles, cogeneration, fuel cells, unused energies, and other reproducible energies); (3) NEDO related supportive institutions (new energy introduction promotion projects by NEDO, and the outline of different supportive institutions); (4) new energy introduction flow (total flow leading to the introduction, and introduction flow by new energies); (5) the grand new energy prize in Kinki District (what is the grand new energy prize? and cases of prizes awarded in Kinki District); (6) new energy related supportive institutions (a list of the related institutions, and the outline of different supportive institutions); and (7) new energy consultation windows and contacts (consultation windows and contacts for general new energy aspects and the government related supportive institutions, and consultation windows by new energies). The grand new energy prize is awarded by New Energy Foundation as the 'institution for public recognition of new energy devices of the 21st century type'. (NEDO)

Making of composite type energy introduction models in cities; Toshi ni okeru fukugogata energy donyu model no sakusei

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The paper made and studied simulation models in case of introducing new energy of composite type to cities. In the study, using a standard composition unit of city as a cluster, the compositional element was divided into 25 cells, which were divided into the residence superiority cell and the business superiority cell. The residence superiority cell was divided into highrise and lowrise. The calculation program is to simulate effects of introducing new energy such as the photovoltaic power generation, solar energy utilization, waste power generation, cogeneration, and unused energy like river water and waste water. Using the program, the analysis of sensitivity was conducted concerning how the outputs will change according to differences in energy consuming composition in the urban area. The calculation was conducted concerning local cities of the warm area, local cities of the cold area, local cities of the subtropical area, residence/working-place neighboring core cities in the warm area, central areas of large cities of the warm area, and new towns of the warm area. 28 figs., 27 tabs.

Investigation into introduction and promotion of clean energy cars; Clean energy jidosha no donyu sokushin ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Gazing the introduction target for fiscal 2000 and 2010, the paper arranged comprehensively and systematically the trend in Japan and overseas of clean energy cars and described subjects. Themes of the study to be promoted in terms of electric cars are: Li secondary batteries, heightening of performance of batteries such as Ni-hydrogen, power generation/power storage hybridization to make the long-distance travel possible. For the price reduction, the body is so made as to make it possible to select three kinds of power unit, that is, gasoline, hybrid, and electricity. Low noise and easy operation are also important. As to natural gas vehicles, the price is more than three times as high as that of gasoline vehicles, and relaxation of the related regulations on metal tanks, the Road Traffic Act, etc. is necessary. It is indispensable to establish quantity production and technical standards and reduce cost by the remodeling for bi-fueling with gasoline engines, development of FRP tanks, etc. Methanol vehicles are the closest to gasoline vehicles, but the introduction is delayed having no groups for generalization. Solar and hydrogen cars are promising, but are on a stage of developing the basic technology. 43 figs., 104 tabs.

Basic research report on introduction of new energy into Yamaguchi Prefecture; Yamaguchiken shin energy donyu kiso chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In Estimation Work 1, the potentially available amount (the amount in existence) is determined for each type of new energy by use of various new energy related technologies now available. In Estimation Work 2, the available amount is determined for each type of new energy, with social restraint and installation space taken into consideration. Effects upon energy saving and CO2 emission reduction are 4405.2% and 3439.1% in Estimation Work 1, and 6.5% and 8.0% in Estimation Work 2. A conclusion is reached after examining the outcomes of the said estimation works and the results of simulations (conducted on the assumption of new energy introduction in fiscal 2010), the number of advocates expressing their support of new energy adoption in questionnaires answered by various businesses and offices in the prefecture, high possibilities of introduction detected in a survey of exploitation projects of cities, towns, associations, and unions, and the prospect of acceptance by households. The conclusion is that the types of new energy and technologies to be selectively introduced into the prefecture will be photovoltaic power generation, wind power generation, clean energy vehicles, energy extracted from wastes, cogeneration, fuel cells, passive solar system, utilization of waste heat from factories and mills, and ocean energy. These are abundant in terms of potentially available amount and of available amount. (NEDO)

Report on the FY 1999 survey for making a data book related to new energy technology development. Trends of solar energy utilization, waste power generation, clean energy vehicle, geothermal power generation, clean coal technology, other new energy technology and new energy technology development; 1999 nendo shin energy gijutsu kaihatsu kankei data shu sakusei chosa hokokusho. Taiyonetsu riyo, haikibutsu hatsuden, clean energy jidosha, chinetsu hatsuden, clean coal technology, sonota no shin energy gijutsu, shin energy gijutsu kaihatsu kanren doko

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The paper collected/arranged the most up-to-date data made public in the new energy technology field. As to the solar energy utilization, the utilization is on the decrease with the beginning of the 1980s as a peak, and the solar systems introduced in FY 1998 totaled 15,000 and the water heaters 56,000. The waste power generation is showing a steady growth both in the general use and in the industrial use, and the introduction of 5 million KW is expected for FY 2010. The sale of the hybrid car started at the end of 1997, and the subjects are the price/performance/fuel supply system. Concerning the geothermal power generation, 497,000 KW and 36,000 KW were introduced for business use and non-utility use, respectively. Japan ranks sixth among nations of the world. Relating to the coal liquefaction, the pilot plant (PP) of Japan's original bituminous coal liquefaction NEDOL process finished operation in 1998, and the construction of technology package, international cooperation, etc. are being conducted. About the coal gasification, the construction of demonstrative equipment and operation are planned during FY 2002 - FY 2007, making use of the PP achievements of IGCC. In regard to the biomass-based waste power generation, the lignocellulose system is large in potential quantity. As to the hydrogen energy, the WE-NET project entered Period II. With respect to the ocean thermal energy conversion, the demonstrative study started. In relation to the wave power generation, a small size of approximately several hundred W was commercialized. (NEDO)

Research and development of system to utilize photovoltaic energy. Survey on the evaluation of photovoltaic power generation; Taiyoko hatsuden riyo system no kenkyu kaihatsu. Taiyoko hatsuden hyoka no chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the survey results on evaluation of PV power generation in fiscal 1994. (1) On the evaluation technique of energy pay-back time, foreign trial calculation examples by integration method were surveyed. However, there were not many study examples, and the calculation basis of input energy was also ambiguous. The calculation result by input-output analysis in Japan gave the value more than that by integration method, pointing out that indirect input energy is essential. (2) On the evaluation technique of the degree of environmental contribution, CO2 emission of the PV generation system installed on ordinary housing roofs was calculated to estimate reduction of CO2 emission and cost. As a result, PV power generation as reduction measures against CO2 brought a little cost increase. (3) On the latent scale of PV power generation, it was estimated to be nearly 191GW although under no restriction. It was a considerably large value as compared with the current power generation capacity in Japan. 4 tabs.

Prospects to solar energy power generation in space. Uchu taiyo hatsuden eno tenbo

Energy Technology Data Exchange (ETDEWEB)

Kudo, I. (Electrotechnical Laboratory, Tsukuba (Japan))

1993-05-01

Solar energy power generation in space uses large arrays of solar cells developed on a geosynchronous orbit to obtain electric energy, which is transmitted to the earth using microwaves. The idea had already been advocated in 1968, which was followed a decade later by joint discussions done by NASA and DOE. The concept intended to take care of the U.S. power demand by using 60 power plant satellites, each having an output of 5 GW. This expanse of the scale, regarded reasonable even today, calls for the solar cell arrays in space spreading over an area of 10 km [times] 5 km if silicon solar cells with a conversion efficiency of 15% are used, and rectenna on the ground (a received wave converting facility) forming an ellipse of 10 km [times] 13 km (assuming a location at the north latitude of 36[degree]). Although there are a number of problems in the idea such as transportation means to lift construction materials into the space and effect of microwaves on the ionosphere and the ecosystems, the Agency of Industrial Science and Technology organized a 'committee for investigating and studying the space power generation systems' in the fiscal year 1991, and has been moving discussions forward since then. 7 refs., 5 figs.

Survey on the cost of the photovoltaic power system; Taiyoko hatsuden cost chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Comparisons were made of the power generation cost in Indonesia and Thailand between the photovoltaic power system and other power systems. From the difference in technical standards with Japan, trially calculated were the amount of the potential introduction and the possibly reduced cost. In Indonesia, a plan has started for the introduction of a 50W system to 1 million houses in the unelecrified area, but the introduction has not been so promoted as planned. In Thailand, a plan is being carried out for the introduction of the battery charge station system, but the introduction has remained small-scaled. Comparisons were made among the solar home system in Indonesia, the battery charge station system in Thailand, the diesel engine power generation, and the grid connection with the existing power distribution system. The result concluded that the solar home system is low-priced though it depends on the distance from the existing distribution line and the power consumption amount. Moreover, it was found that the system would be more economical than in the case of Japan if obeying international standards for the photovoltaic power system. 6 refs., 15 figs., 56 tabs.

Research and development of photovoltaic power system; Taiyoko hatsuden system no jissho kenkyu

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the result obtained during fiscal 1994 on a demonstration research on photovoltaic power generating systems. Solar cells with an output of 750 kW, storage battery facilities with an output of 3,058 kWh, three DC-AC converters with a rating of 250 kW, and a diesel generator with an output of 300 kW having been installed up to the previous fiscal year were combined to perform comprehensive adjustments and tests such as battery charge/discharge tests and AC parallel operation tests. The battery charge/discharge tests revealed that the 10 hour rate discharge capacity meets the specifications, and the batteries are free of deterioration after a demonstration operation of about 4.5 months. Difference between the power generation record and the planned value is thought due to the following reasons: the array output data in a power line connected system come about 90% of the simulation result due to correction coefficient for the solar cell conversion efficiency; the inclined face insolation results in less by about 7% than the planned value, and the transmittable power amount less by about 14% in total; the load power amount is less by about 7% than the planned value; and the balance supplementing power factor increases by about 4%. 5 figs., 2 tabs.

Design manual of the wind power system; Furyoku hatsuden system no sekkei manual

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

For the purpose of contributing to the promotion/introduction of the wind power generation in Japan, systematical arrangement was made on items, standards/related laws, etc. to be considered upon designing the wind power system, further describing design examples of the standard system (case study). Out of the items necessary for the design, as to the investigation, arranged were matters and methods to be field-surveyed such as the site situation, surroundings, radio wave hindrance, noise hindrance, measurement, geology, etc. Concerning the determination of sizes of wind turbines to be introduced, procedures for setting sizes of wind turbines suitable for the places proposed for the installation were described. In the design, the knacks were summed up of designing wind power generation facilities, electric equipment, electric works, civil engineering, and measuring instrument. As to the working plan, indicated were the points to be taken notice of in the plan and the standard working process. Also shown were the evaluation method of economic efficiency, etc. In addition, the paper includes the related laws, system design examples, and the data attached. 10 refs., 13 figs., 59 tabs.

Electric power of residential photovoltaic power system; Jutakuyo taiyoko hatsuden system no hatsudenryo

Energy Technology Data Exchange (ETDEWEB)

Asano, K.; Kawamura, H.; Yamanaka, S.; Kawamura, H.; Ono, H.; Hayashi, K.; Naganawa, H. [Meijo University, Nagoya (Japan); Asai, H.

1996-10-27

Measurement was done on the annual power generation of a residential photovoltaic power system that was most suitable for the present situation in utilizing solar energy; and an examination was made on the basis of the data of a module in which an optimal operation load control was separately installed in order to operate the system more effectively. As a result, it was found that the introduction of a 3kW class system was currently most desirable as a residential photovoltaic power system, and that the problem of the optimal operation load control was crucial for the more efficient power generation. The resistance value of the optimal operation load was stable between 6 and 8 ohm in the daytime in fine weather. However, it was observed that, where no sufficient insolation was expected, the optimal operation load was ten times as much as in fine weather, being easily influenced by the environmental elements. In addition, it was revealed that, if the operation load was fixed at a specific value (6 ohm) in a clear day, the power generation was only about 85% compared with the case of controlling the optimal operation load. This figure was obtained under comparatively favorable conditions, however. 8 refs., 7 figs.

Data book of new energy introduction to Hokkaido. FY 2000 version; Hokkaido shin energy donyu data shu. 2000 nendoban

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of effectively introducing/promoting new energy and of supplying the basic data which contribute to the promotion/education, the actual results of new energy introduction to Hokkaido were collected/arranged. New energies to be surveyed were the photovoltaic power generation, solar heat utilization, wind power generation, waste power generation, waste heat utilization, waste fuel production, biomass energy, unused energy, gas generation, petroleum cogeneration, fuel cells, clean energy vehicles, small-/medium-scale hydroelectric power generation, etc. The purpose of the book is mainly to collect the basic information, that is, what kind of new energy has been introduced to what kind of area. The data are so collected that facilities adopting new energy can be seen as unit of city/town/village as a rule. The method to collect information is based on the total collection of the reports made by organizations in/outside Hokkaido. The book additionally covers the details of the data supplied and the data collected. (NEDO)

17th Symposium of NEDO projects. Introducing/spreading project subcommittee; Donyu fukyu jigyo bunkakai. Dai 17kai jigyo hokokukai

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-09-01

The results of the following themes are presented in this subcommittee; (1) outline of the new energy introduction promotion department, (2) the project results, and (3) introduction of the examples. For the theme (1), NEDO is supporting the projects for introducing and promoting new energy systems, feasibility studies for introduction of these systems, and field test (FT) projects to accumulate the experiences, e.g., collecting the data by operating these systems under actual loads, development and technology demonstration projects for introduction of new energy systems, and advisory projects for supporting introduction of new energy systems. For the theme (2), those results reported include the results and examples of the FT projects for power generation by photovoltaic cells and wind power generation, results of the FT project for power generation by fuel cells and creation of the FT projects for pioneer high-efficiency energy systems, current status of the environment-friendly energy community projects (heat supply systems), results and examples of the environment- friendly energy community projects (power generation projects), demonstration tests for establishing the distributed power supply systems of the next generation, tests for establishing techniques for, e.g., load-leveling in power generation by photovoltaic cells for residential purposes, results of the project for technology of utilizing unutilized energy, survey on the techniques for power generation by wastes, and advisory projects for supporting introduction of new energy. (NEDO)

Investigations on installation of the heat exchange system in geothermal wells; Chinetsu koseinai netsukokan system donyu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The heat exchange system in geothermal wells is a system that replaces the air source heat pump and uses underground beds or groundwater as a heat source to heat rooms by collecting underground heat in winter, and cool rooms in summer by operating a heat media circuit in reverse direction through the action of a reverse flow valve to discharge heat underground. This paper describes feasibility investigations on the system including its technical trend for introducing the system technology. Technological and economic discussions were given by classifying the intra-well heat exchange device in its installation direction (horizontal loop type and vertical installation type), underground heat exchange media (antifreeze solution/water cyclic system and direct expansion system), and underground heat transfer (heat conduction system and heat convection system). As a result of discussing each system, it was concluded that the following two systems are promising: A = vertical installation, antifreeze solution/water cyclic and heat conduction system, and B = vertical installation, antifreeze solution/water cyclic and heat convection system. Since the system B was found to have better efficiency and economy among both systems, it is necessary to verify an intra-well heat exchange system and operation methods that suit the system B effectively. 21 refs., 8 tabs.

Feasibility study on introducing new energy systems into Asian villages; Asia sonraku ni okeru shin energy donyu kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

For improvement of living standards in unelectrified areas of Asia, the feasibility of new energy power generation systems was surveyed. The degree of electrification of local areas is different every country, and Thailand is ahead of other countries, while Laos and Cambodia are most unelectrified. Power supply of 100W/house seems to be adequate for local areas because of weather condition, housing situation and life-style. Economic support and education on electricity are necessary for poor areas. Although needs for new energy is increasing, the priority is given to industrial and urbanized areas because of cost and investment effects, and remote areas are dependent on grant- in-aid. Resources of photovoltaic, wind power and micro- hydraulic energies are abundant, however, selection of energy and verification of its usability are important, and the local energy density maps were thus prepared. In introduction of new energy, after selection of energy suitable for an area concerned, such geographical and social conditions should be surveyed as road condition, water rights, land utilization, economic support system, policy and intention of inhabitants. 76 refs., 68 figs., 91 tabs.

Subsidy project in fiscal 1999 to accelerate forming an environment harmonizing energy community. Report on the survey on energy supply investigation project by using a wastes electric power generation system in wide city and village area in the Joso area; Joso chiho koiki shichosonken ni okeru haikibutsu hatsuden ni yoru energy kyokyu chosa jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Discussions were given on the feasibility of a project to be performed jointly by the Business Bureau of the Ibaraki Prefectural Government who takes charge of the wastes electric power generation project, and the Joso Area Wide City and Village Area Affair Association who performs refuse disposal project. The basic plan for the system may be summarized as follows: the gasification melting furnace shall have a capacity of 420 tons per day, discharge concentrations of dioxins shall be 0.01 ng-TEQ/m{sup 3} or less, the power generation system shall be the steam high-temperature high-pressure system, the power generation efficiency shall be 25%, and the electric power generation takes priority, with the steam after power generation use utilized for heat supply. The evaluation on the effect of introducing the project can be summarized as follows: in the social aspect, the execution of the joint project is safe and effective for the residents and society; it contributes to activation of the areas and assistance to the regional activities; correspondence will be possible to the tighter enforcement of the laws and regulations in the future; in the environmental aspect, discharge of carbon dioxide, sulfur oxides, and dioxins can be suppressed; and in the economic aspect, the ultimate disposal quantity in refuse treatment will be reduced greatly, serving for saving the treatment expense, and the refuse treatment cost may be reduced by assuring the earning from selling the electric power. (NEDO)

FY 2001 report on the results of the survey of the environmentally friendly type energy community project. Utilization of combustible waste as solid fuel in Shimizu City, Shizuoka Prefecture, and the wide spread sphere of municipalities (Facilities such as RDF+LNG combined use high efficiency waste power generation); 2001 nendo Shizuoka ken shimizu shi oyobi koiki shichoson ken ni okeru kanensei haikibutsu kokeika nenryo riyo kankyo chowa gata energy komyuniti keisei sokushin hojo jigyo chosa (RDF+LNG heiyo kokoritsu haikibutsu hatsuden tou shisetsu) chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

Survey/study were conducted of viability of an idea of the high efficiency power generation that combinedly use RDF from the refuse generated in Shizuoka/Yamanashi/Nagano prefectures and LNG from the LNG base in Shimizu City, Shizuoka Prefecture. In the survey of raw materials for RDF, the present amount that can be supplied to RDF power generation was estimated at 280 t/d in RDF and 4,300 Kcal/kg or more in heating value. As to the RDF/LNG combination power generation, combinations of RDF200t/d + 25MW (capacity of gas turbine power generation) or RDF200t/d + 70MW seem to be appropriate. And, 30% or more of RDF power generation efficiency is made possible. In the study of economical efficiency, expenses born by local governments were calculated supposing that the difference between the unit price of power selling and that of power generation in power generation is born by RDF suppliers. As a result, the share becomes approximately 8,600-12,000 yen/refuse t in 15-year operation, and was found lower than that in the existing small-/medium-scale refuse incineration treatment. The combustion flue gas associated with the power generation business becomes approximately 300,000 Nm{sup 3}/h. The gas turbine fuel is natural gas, and RDF is good in combustibility. Therefore, the effect on the environment is expected to be small. (NEDO)

Development of large scale and wind energy conservation system. Operational studies on a large-scale wind energy conservation system; Ogata furyoku hatsuden system no kaihatsu. Ogata furyoku hatsuden system no unten kenkyu

Energy Technology Data Exchange (ETDEWEB)

Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

Described herein are the results of the FY1994 research program for operational studies on a large-scale wind energy conversion system. A total of 8 domestic and foreign cases are studied for wind energy conversion cost, to clarify the causes for higher cost of the Japanese system. The wind power systems studied include Japanese (5 units at Tappi Wind Park, the same type supplied by company M), US (California Wind Farm, 300 units) and UK (Wales Wind Farm, 103 units) systems. The investment costs are 639, 285 and 189 thousand yen/kW for the Japanese, US and UK systems, respectively. It is also revealed that the power plant itself and assembling costs account for a majority (70 to 88%) of the total investment cost. The higher cost of the Japanese system results from a smaller number of units installed, and the power plant cost can be drastically reduced by mass production. Increasing size also reduces cost greatly.

Study on closed cycle MHD generation systems; Closed cycle MHD hatsuden system no kento

Energy Technology Data Exchange (ETDEWEB)

NONE

1988-03-01

The closed cycle noble gas MHD generation systems are surveyed and studied. The concept of closed cycle noble gas MHD generation is confirmed to extract high enthalpy, and now going into the engineering demonstration stage from the basic research stage. These systems have various characteristics. The highest working temperature is around 1,700 degrees C, which is close to that associated with the existing techniques. Use of helium or argon gas as the working fluid makes the system relatively free of various problems, e.g., corrosion. It can attain a much higher efficiency than the combined cycle involving gas turbine. It suffers less heat loss in the passages, is suitable for small- to medium-capacity power generation systems, and copes with varying load. The compact power generation passages decrease required size of the superconducting magnet. The technical problems to be solved include optimization of power generation conditions, demonstration of durability of the power generation passages, injection/recovery of the seed material, treatment of the working gas to remove molecular impurities, and development of heat exchangers serviceable at high temperature produced by direct combustion of coal. The conceptual designs of the triple combined system are completed. (NEDO)

Trend of development of dispersion energy machine. Solar power generation system; Taiyoko hatsuden shisutemu

Energy Technology Data Exchange (ETDEWEB)

Oda, T. [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

2000-04-01

Technology development of a solar power generation system is advanced in Japan taking the New Sunshine Subject (NSS) of the Agency of Industrial Science and Technology as the center. According to the initial stage plan (in fiscal 1993 to 2000) of the NSS, a general goal is to establish the technique which supplies electric power at the power generating cost (the production base cost) being equal to the electricity fees (20 to 30 yen/kWh) for normal families in the latest year. At present, introduction of the solar power generation system results in the reduction of about 1 million yen per kW. It is expected that 5 hundred thousand yen per kW is reduced by the present technology with a combination of cost reduction of solar battery modules, cost reduction of relevant equipment such as inverters, and rationalization of installation fees. It is necessary to realize 3 hundred thousand yen per kW for realizing the price having competition in the power supply market. In this paper, popularization prediction and popularization promotion countermeasures of the solar power generation system are concretely explained. (NEDO)

Fiscal 1980 Sunshine Project research report. Development of hydrothermal power plant (Development of binary cycle power plant); 1980 nendo nessui riyo hatsuden plant no kaihatsu seika hokokusho. Binary cycle hatsuden plant no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

This report summarizes the fiscal 1980 research result on evaluation of elementary technology studies, research on plant technologies, and assessment of profitability for development of the next 10MW class large binary cycle power plant. In evaluation of heat media and heat cycles, selection of heat media and preparation of specimens through document survey, measurement of thermal characteristics, and preparation of pressure-enthalpy charts were carried out for selection of promising media. In evaluation of materials, as the field corrosion test and simulation results on 3 kinds of welding materials, it was concluded that SUS316 is best as material. In evaluation of heat medium turbine, through the test on oil film seal and mechanical seal techniques, various information were obtained. In evaluation of mist-cooling condenser, experiment on the basic unit heat exchanger, and study on the optimum design were carried out. In addition, research on plant technologies, and assessment of profitability were conducted. (NEDO)

FY 1998 Report on development of large-scale wind power generation systems. Feasibility study on development of new technologies for wind power generation (Study on the development of wind power generation); 1998 nendo ogata furyoku hatsuden system kaihatsu. Furyoku hatsuden shingijutsu kaihatsu kanosei chosa (furyoku hatsuden gijutsu ni kansuru kaihatsu doko chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This survey is designed to analyze, e.g., current status of large-scale wind power generation devices/system technologies and development trends worldwide, and to make predictions about future developments, in an effort to contribute to advancements in new technology for wind power generation systems in Japan. The international R and D cooperation programs promoted by IEA and EU have helped the participants produce a number of good results at lower costs. The European countries have developed the wind power generation industries in each area, promoted by the governmental subsidy policies, and are leading the world. The system is becoming larger, from around an average unit capacity of 250kW in the beginning of the 90's to 600kW now, reducing the cost by the scale merit. The improved computer capacity has made it possible to more easily analyze the complicated rotor aerodynamics, structural dynamics, wind characteristics and other factors related to wind power generation systems. The future R and D directions will include world standards for large-scale wind turbines, advancements in wind farm technologies, offshore wind power generation systems, advancement in design technologies, and new concepts for wind power turbine designs, e.g., floating wind turbine. (NEDO)

Report for fiscal 1998 on feasibility study for introduction of electric automobiles; 1998 nendo denki jidosha donyu kanosei chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Surveys have been made on the characteristics of environmentally harmonizing automobiles, and the status of development and introduction thereof inside and outside the country. Discussions were given on the possibility of introducing electric automobiles in Japan. In developing environmentally harmonizing automobiles in Japan, works have been executed on low pollution type components such as lean burn engines, electric automobiles, gasoline engine and electric motor hybrid cars, methanol fueled cars, and fuel cell automobiles. Some of them are already in use in spite of their high price. In America, a cooperation project for the next generation cars has been implemented by mobilizing industrial, academic and governmental organizations. Based on the achievements thereof, the car makers have announced their original advanced cars respectively. In the EU, development of low exhaust gas cars and zero emission cars is being carried out jointly by the related industries setting years 2003 to 2005 as the target. An urban type traffic system utilizing electric vehicles, and a traffic system dividing movements of short distance and long distance are proposed as the means to introduce the future electric automobiles. (NEDO)

Effects of peak shaving technologies in the residential and commercial sector; Minsei bumon no fuka heijunka gijutsu no donyu koka

Energy Technology Data Exchange (ETDEWEB)

Nagata, Y. [Kyoto University, Kyoto (Japan); Takahashi, M.; Uchiyama, Y. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

1997-09-01

This paper analyzes how much of the power demand could be reduced in the future by improving efficiencies of electric power utilizing appliances used in the residential and commercial sector. It discusses whether the reduction would lead to load leveling. Annual load rate in the power demand is continuing to decrease because of power demand increase in the residential and commercial sector, and increase in demand for air conditioning in summer. If a technology to improve electric appliance efficiency is proliferated to its maximum scope, the annual load rate in fiscal 2014 may be improved by 1.1 percent point. Since the improvement allows new power generation facility installation cost to be deferred, the power generation unit cost can be reduced by 0.11 yen per kwh. If a heat storage type air conditioning technology is proliferated to its maximum scope, the annual load rate in fiscal 2014 can be improved by 1.8 percent point, and the power generation cost may also be reduced. If the device efficiency improving technology and the heat storage type air conditioning technology are introduced to their maximum simultaneously, the annual load rate in fiscal 2014 can be improved by 2.5 percent point, and the power generation cost may also be reduced by 0.24 yen per kwh. If a promotion policy is taken on proliferation of a specific device efficiency improving technology having excellent economic performance by providing subsidy, the reduction amount of cumulative power generation expense will be much greater than the required subsidy amount. 10 refs., 9 figs., 22 tabs.

FY 1999 data book for the introduction of new energy to Hokkaido; 1999 nendoban Hokkaido shin energy donyu data shu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of effectively promoting the introduction of new energy to Hokkaido, it is necessary to comprehensively/systematically arrange various kinds of new energy and to furnish the basic data which contribute to the spread/education. The paper collected/arranged the actual results of the introduction of new energy to Hokkaido, using the existing data, etc. Attention is paid to the collection of the basic information on what kinds of new energy have been introduced in what kinds of regions, etc. Fundamentally, the data were collected by which facilities for new energy can be seen by city/town/village. The new energy for collection is basically within the range of those included in the New Energy Law. They are renewable energy (photovoltaic power generation, solar heat utilization, and wind power generation); recycle type energy (waste power generation, waste heat utilization, fuel production, waste fuel production, biomass energy, and unused energy); new forms of the existing energy (gas/oil cogeneration, fuel cell, and clean energy vehicle). (NEDO)

Report on a project to support promotion of forming an environmentally friendly energy community. Survey on an environmentally friendly community business by means of high-efficiency wastes power generation system in the Toyota-Kamo wide area; Kankyo chowagata energy community keisei sokushin hojo jigyo chosa hokokusho. Toyota Kamo koikiken kokoritsu haikibutsu hatsuden kankyo chowagata energy community jigyo chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Taking the Toyota-Kamo wide area as the object, wastes power generation is positioned over the society system as worked on by administrations and operators integrally to incinerate mixedly those incineratable materials such as plastics among general and industrial combustible wastes for high-efficiency generation of power, which is supplied to electric utility operators as surplus power. Discussions were given on the business feasibility and the effectiveness as a society system. In this area, the mixed model B plan (dealing with general wastes plus industrial wastes) was evaluated as an effective plan as the society system. This is because the plan has effect to incinerate, melt and generate power from industrial wastes which have been used for land-fill, effect of improving the power generation efficiency, and effectiveness of mixed treatment with general wastes. The plan A in which general wastes are made into RDF, then incinerated mixedly with industrial wastes for power generation was evaluated to have high reliability potential of power supply and to be an effective plan as a society system, if effect can be expected to reduce transportation energy as a result of making the system large enough and turning wastes into RDF. (NEDO)

Development of large scale wind energy conservation system. Development of control techniques for assembly-type wind power generating systems; Ogata furyoku hatsuden system no kaihatsu. Shugogata furyoku hatsuden system no seigyo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

Described herein are the results of the FY1994 research program for development of control techniques for assembly-type wind power generating systems. The study on optimum system configuration produces 50 to 100kW wind power units for screening small-size wind power plant types, and, at the same time, surveys performance of commercial units and experiences of 9 makers capable of producing the above units. As a result, 3 MICON`s units (output: 100kW, active YAW control, monopole tower, maximum wind speed: 60m/s) are selected. The study on optimum operational techniques integrates 2 medium-size power units into a power line, showing a service factor of 30.2% on the annual average, monthly varying in a range from 11.8 to 45.0%. These units, installed in Miyako Island, were attacked by 3 typhoons of wind velocity of 25m/s or higher in 1994, and the only damage recorded is that of the anemoscope/anemometer. It is found that No.1 unit is located at a better geographical point than the No.2 unit, to produce a higher output. 3 figs., 3 tabs.

Effect of fall wind on wind power generation; Furyoku hatsuden ni okeru dashikaze no koka

Energy Technology Data Exchange (ETDEWEB)

Nagai, H [Nihon University, Tokyo (Japan)

1997-11-25

Wind conditions in Arakawa Town, Niigata Prefecture, were surveyed by anemometers and anemoscopes installed at 3 different points, and the data are analyzed to develop the prediction model for investigating possibility of introduction of wind mills there. Outlined herein is power generated by fall wind by comparing predicted power availability with the actual results. In order to investigate possibility of power generation by fall wind, the wind conditions and power availability are simulated using the observed wind condition data. Predicted wind velocity involves a large error at a point where frequency of prevailing wind direction is high, and direction in which average wind velocity is high coincides with direction in which land is slanted at a high slope. Fall wind occurs locally for geographical reasons. Location of the wind mill must be carefully considered, because it is complex, although potentially gives a larger quantity of power. A wind mill of 400kW can produce power of around 600MWh annually, when it is located at the suited site confirmed by the wind condition analysis results. 6 refs., 5 figs., 6 tabs.

Energy saving house utilizing photovoltaic system. 3; Taiyoko hatsuden wo donyushita sho energy jutaku. 3

Energy Technology Data Exchange (ETDEWEB)

Itsumi, J. [Kumamoto Institute of Technology, Kumamoto (Japan)

1997-11-25

Various measurements are conducted in an energy-efficient house equipped with a photovoltaic power generation system and actually lived in by people, and matching between the household load and photovoltaic power generation, and the consumption of power, are examined. As the result investigation of power consumption in the house, it is found that 13.31kWh is consumed in the daytime in winter, and 14.15kWh in summer. Thirty-two 153W modules are used, and they produce 12.74kWh in four hours on a fine summer day, which amount nearly satisfies the demand of the household. As for the records during a year beginning in May, 1996, it is found that an annual amount of 4326kWh was generated, with 68% being surplus and 32% consumed for the household. Details of the household consumption were that 49.2% was consumed for house heating and cooling and 34.1% for cooking, the two in total occupying more than 80% of the whole household consumption. Energy-saving behavior is evaluated by comparing the energy-efficient house with some ordinary residential houses in Kumamoto City, and it is found that there is a yearly difference of 104,310 yen in electricity bill or 47% in energy saving effect. 5 refs., 4 figs., 4 tabs.

Load averaging system for co-generation plant; Jikayo hatsuden setsubi ni okeru fuka heijunka system

Energy Technology Data Exchange (ETDEWEB)

Ueno, Y. [Fuji Electric Co. Ltd., Tokyo (Japan)

1995-07-30

MAZDA Motor Corp. planed the construction of a 20.5MW co-generation plant in 1991 for responding to an increase in power demand due to expansion of the Hofu factory. On introduction of this co-generation plant, it was decided that the basic system would adopt the following. (1) A circulating fluidized bed boiler which can be operated by burning multiple kinds of fuels with minimum environmental pollution. (2) A heat accumulation system which can be operated through reception of a constant power from electric power company despite a sudden and wide range change in power demand. (3) A circulating-water exchange heat recovery system which recovers exhaust heat of the turbine plant as the hot water to be utilized for heating and air-conditioning of the factory mainly in winter. Power demand in MAZDA`s Hofu factory changes 15% per minute within a maximum range from 20MW to 8MW. This change is difficult to be followed even by an oil burning boiler excellent in load follow-up. The circulating Fluidized bed boiler employed this time is lower in the follow-up performance than the oil boiler. For the newly schemed plant, however, load averaging system named a heat accumulation system capable of responding fully to the above change has been developed. This co-generation plant satisfied the official inspection before commercial operation according the Ministerial Ordinance in 1993. Since then, with regard to the rapid load following, which was one of the initial targets, operation is now performed steadily. This paper introduces an outline of the system and operation conditions. 10 refs.

Soft energy/seawater pumped-storage power plant in Okinawa; Sofuto energy/Okinawa kaisui yosui hatsuden

Energy Technology Data Exchange (ETDEWEB)

Tsutsui, S. [Univ. of Ryukyus, Okinawa (Japan). Faculty of Engineering

1995-11-15

A demonstration seawater pumped-storage power plant which is the first one in the world is under construction in the northern area of Okinawa. The pumped-storage power generation is an electricity recycling system in which the surplus electricity during the night is utilized to pump up water to an upper reservoir to discharge water for power generation during the daytime when demand for electricity increases. It is scheduled that main civil engineering structures are constructed during the year of 1995 to be subjected to trial operation in the following year. Countermeasures to be taken for natural environmental protection during the plant construction are introduced. Countermeasures are devised for environment assessment, muddy water treatment, and prevention of seawater at the upper reservoir. Salinity in the atmosphere is to be measured during the construction work and the demonstration test to evaluate the effects of scattering of salt from the upper reservoir into the atmosphere on the vegetation in the peripheral area and the salt-resistance of vegetation. Sufficient consideration is given to the protection of the existing vegetation and coral, and to the protection of small living creatures. Participants in the construction work are requested to report, for the purpose of taking proper steps, sites, peripheral conditions, and others when precious animals are found. 9 figs., 1 tab.

Report on studies on closed cycle MHD power generation; Closed cycle MHD hatsuden kento hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-04-01

Summarized herein are results of the studies on closed cycle MHD (CCMHD) power generation by the study committee. The studied system is based on the MHD gas turbine combined Brayton cycle of about 500,000 kW in output power, firing natural gas as the fuel, and the conceptual design works therefor are completed. The major findings are: the overall plant efficiency: 54.2% at the power transmission side, plot area required per unit power output: 0.04 m{sup 2}/KW, unit construction cost: 251,000 yen/KW, and unit power generation cost: 10.2 yen/KWh. This system will be more operable than the gas turbine combined cycle with steam system, because start-up time, output change rate, optimum load and so on are constrained not on the power generator side but on the gas turbine side. The expected environmental effects include the exhaust gas NOX concentration being equivalent with that associated with the conventional power generator of 2-stage combustion system, quantity of combustion gases to be treated being approximately 40% of that associated with the gas turbine combined cycle, and reduced CO2 gas emissions, resulting from enhanced power generation efficiency. It is expected that the CCMHD system can exhibit higher efficiency than the high-temperature gas turbine combined cycle system. (NEDO)

Energy conservation house by photovoltaic system. 2; Taiyoko hatsuden wo donyushita sho energy jutaku. 2

Energy Technology Data Exchange (ETDEWEB)

Itsumi, J. [Kumamoto Institute of Technology, Kumamoto (Japan)

1996-10-27

Photovoltaic power generation system was once placed in excessive expectation what with a growing tendency toward environmental issues and what with vulnerability in supply and demand of energy. However, its utilization was negative because of the low energy conversion efficiency and the high cost. Then, gradually the wind shifted round to the improvement in solar cell efficiency, reduced cost, implementation of subsidizing policy by MITI, purchase of excess power by electric power companies and the amendment of the Electricity Enterprises Act, encouraging the use of the system again. In addition, with a lesson from the Great Hanshin Earthquake, the merit of the system was appreciated as a life-support power source, motivating house-builders. Earlier, the authors had reported designs of energy-saving homes, system structures of photovoltaic power generation, etc. This paper presents the power generation record of a year old system and an example of the comfortable sealed residential room environment, etc., created with the use of the power thus obtained. The annual power generation was 4,088kWh, 30% of which was used in the house and 70% of which was sold as an excess power, resulting in the purchase of power for 6,642kWh. 5 refs., 4 figs, 2 tabs.

Present status of geothermal power development in Kyushu; Kyushu ni okeru chinetsu hatsuden no genjo

Energy Technology Data Exchange (ETDEWEB)

Akiyoshi, M. [Kyushu Electric Power Co. Inc., Fukuoka (Japan)

1997-10-20

The present situation was introduced of the geothermal power generation in Kyushu. In Kyushu, where there are lots of volcanos and abundant geothermal resources, the geothermal exploration has been made since long ago. Three non-utility use units at three geothermal power generation points and six commercial use units at five points are now in operation in Kyushu. The total output is approximately 210 MW, about 40% of the domestic geothermal power generation. At Otake and Hacchobaru geothermal power plants, the Kyushu Electric Power Company made the geothermal resource exploration through the installation/operation of power generation facilities. At the Otake power plant, a geothermal water type single flashing system was adopted first in the country because of its steam mixed with geothermal water. At the Hacchobaru power plant, adopted were a two-phase flow transportation system and a double flashing system in which the geothermal water separated from primary steam by separator is more reduced in pressure to take out secondary steam. Yamakawa, Ogiri and Takigami power plants are all for the joint exploration. Geothermal developers drill steam wells and generate steam, and the Kyushu Electric Power Company buys the steam and uses it for power generation. 5 figs., 1 tab.

Half century of wind power generation memoir. Part 1; Furyoku hatsuden hanseiki sono omoide. 1

Energy Technology Data Exchange (ETDEWEB)

Nakata, H.

1995-12-01

This article may be deemed an autobiography of an individual on his development of wind power generation devices. The author began to be interested in electricity while he was a pupil of primary school and during his time of middle school student, when he walked against the strong wind on an embankment, he got an idea to utilize the wind power and succeeded to generate electricity with his handmade wind power generator using a bicycle generator. Afterwards he kept interested in devices utilizing the wind power, in 1973, energy saving was widely promoted due to the oil crises, and taking that opportunity, he established single-handedly a laboratory for development of utilization of the breeze power. Since his retirement from teaching profession in the spring of 1980, he has coped with earnestly the development of wind power generators. He acquired and installed various machine tools for metal works for generators and various machines for wood works for making propellers. In this article, wind power generators using bicycle generators (direct connection type and speed increasing type), small D.C. motors (motors for driving tape recorder, motors for automobile radiator and windshield wiper, etc.) and automobile generators (D.C. generators and alternators) are explained. 11 figs.

On-line temperature control of fluidized bed incinerator using fuzzy algorithm; Fuzzu seigyo donyu ni yoru ryudosogata shokyakuro unten no jidoka

Energy Technology Data Exchange (ETDEWEB)

Okayasu, S.; Kuratani, T.; Imai, H. [Ajinomoto Co. Inc., Tokyo (Japan)

1995-03-15

Automatic control of incinerators for their stable operation has been desired for the preservation of the environment in the factory. An on-line fuzzy control system has been successfully introduced for temperature control of the fluidized bed of incinerator for industrial wastes. In this case, manual control can be applied to the plant instead of a PID control system, because of the complexity of the waste materials and the large delay in detection of the temperature change in the fluidized bed sand. On the basis of analyzing the dynamic performance of the process and the know-how of skilled operators, membership functions and fuzzy control rules are selected, then determined carefully for the system. Introduction of the system resulted in almost the same performance as manual control. Subsequently the operators are freed from manual operation in the control room for an hour. 6 refs., 5 figs., 4 tabs.

Development in fiscal 1999 of technology commercializing photovoltaic power generation system. Research and development of power generation application system and peripheral technologies (Survey and research on evaluation of photovoltaic power generation); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (taiyoko hatsuden hyoka no chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective of evaluating the contribution to the global environment of utilization of photovoltaic power generation, discussions were given on evaluation of photovoltaic system life cycle, evaluation of contribution to environment, and total evaluation. This paper summarizes the achievements in fiscal 1999. In evaluating the PV system life cycle, the roof-integrated modules using the thin film CdTe cells were selected as the evaluation object to estimate the energy payback time (EPT) and the CO2 emission unit consumption rate. In case of annual production of 10 MW, the EPT is 1.8 years and the CO2 emission unit consumption rate is 13 (g-C/kWh), which were found largely reducible by expanding the annual production size. For the environmental contribution evaluation which focuses on CO2 emission suppression effect as the discussion object, discussions are being given on the introduction scenario needed for the analysis. In the total evaluation, the direct employment effect assumed in Japan was discussed on production, distribution sales, installation, maintenance control and dismantling of photovoltaic generation system for residential use. The discussion showed the effect of about 7 persons per year per MW in production size of 100 MW. (NEDO)

Report on achievements in fiscal 1998. Development of technologies to put photovoltaic power generation systems into practical use - Demonstrative research on photovoltaic power generation system (Research on multi-hybrid photovoltaic power generation system); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden system no jissho kenkyu (taiyoko hatsuden multi hybrid system no kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

A multi-hybrid system integrating photovoltaic and wind power generation systems with the existing diesel engine power generation system was assumed for installation in power systems in islands. System analyzing simulation and economic performance analyses were performed to consider system configurations suitable for islands from the viewpoints of system stability and economic performance. The work was progressed by dividing the subject into (1) research on the system configurations, and (2) studies on the economic performance. In performing either work, the power demand was classified as large (in Miyako Island), medium (in Kume Island) and small (in Tarama Island), and the introduction years into 1997, 2000, and 2005. In Item (1), the system parameter specifications were put into order, and the system analyzing simulation was performed, wherein it was verified that the system will be stabilized by introducing a system stabilizing equipment (batteries and an inverter) and by limiting the output from the wind power generation. In Item (2), it was made clear that the power generation cost is equivalent to or lower than the present cost, making reduction in fuel consumption possible. It was also disclosed that the introduction is most effective in small islands, and drop in the power generation amount due to limiting the output from the wind power generation is small. (NEDO)

FY1999 technological development of wind power generation systems for islands. Development of wind power generation systems in islands; 1999 nendo ritoyo furyoku hatsuden system nado gijutsu kaihatsu. Rito ni okeru furyoku hatsuden system no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective of developing wind power generation systems that suit small to medium size islands in Japan, conceptual design was made on a 100-kW class wind mill to satisfy such requirements as no need of large heavy machines, and gust resisting performance. Investigations were performed on sites suitable for demonstration tests thereof. This paper reports the achievements in fiscal 1999. In investigating the site location feasibilities, which took small to medium size islands in Okinawa Prefecture as the discussion objects, environmental investigation, wind condition forecast and investigation, and system linkage investigation were carried out, whereas one point each in three islands were extracted as the promising sites. The system discussion and design called for wind velocity resistance of 80 m/s, system linkage percentage of 40% at maximum, power generation cost of 20 yen per kWh, design life of 20 years, constructability of requiring no large heavy machines, and operation mode of diesel hybrid use. Along with these specifications, conceptual design was performed on the system constituting elements, such as wind mill blades, generators, electric power control devices, and towers. In the blade aerodynamic test, wind tunnel tests were executed by using three types of blade wings. Sample blades were fabricated for the preparation of blade material tests. (NEDO)

Wastes disposal on board a ship. Disposal of sewage and waste water; Senjo no haikibutsu shori. Osui oyobi haisui no shori ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Nakamura, K. [Mitsui Engineering and Shipbuilding Co. Ltd., Tokyo (Japan)

1996-07-25

This paper describes technologies and devices suitable for disposing of sewage and waste water produced in a ship. Methods for disposing of sewage in a ship include such physico-chemical disposition methods as disinfection and sterilization, and such biological disposition methods as activated sludge sewage disposition and catalytic oxidation (biological membrane treatment). Sewage treatment devices include a storage tank type sewage treatment device often used in inner sea liners such as ferry boats, and a biological treatment device (aeration device) used as a mainstream in merchant ships, large passenger liners, and governmental ships. With the storage tank type sewage treatment device, sewage is stored in a storage tank provisionally while a ship is cruising in a discharge prohibited sea area, and discharged in a sea area allowing the discharge or when the ship enters a port. The method is simple, but limited in storage volume. An activated sludge sewage treatment device consists of a tank divided into an aeration chamber, a sedimentation chamber and a disinfection chamber, an air compressor, a chlorine dissolving apparatus, and a screen. Sewage is digested and decomposed by activated sludge, and the top clear water is disinfected by chlorine, and then discharged. 1 tab.

Fiscal 1999 survey report on introducing technique for predicting impact on hot spring; 1999 nendo onsen eikyo yosoku shuho donyu chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-10-01

For the application of fruits of the geothermal development promotion project to survey phase C and for the study of technical means for appropriate development to employ after phase C, some cases of impacts imposed on hot springs by geothermal development were taken up and the causes of the impacts were investigated. Activities were conducted in the three fields of (1) the survey of actualities of impacts imposed on hot springs, (2) the survey of the causes of such impacts, and (3) a comprehensive survey. Keyword searches were conducted into the data system and geothermal energy related magazines, and 13 cases were found in which hot springs were affected by geothermal development, which included the Palinpinon district (Philippines), the Koso district (America), and the Wairakei district (New Zealand). Concerning the 13 cases, data on geology, geological structures, and geothermal fluids were collected and studies were conducted about relations of geothermal development with geological structures and geothermal fluids, as in the case of hot springs, and the two were integrated for the clarification of the causes of impacts. In concluding the report, the difference in mechanism is deliberated between cases with impacts on hot springs and cases without impacts on hot springs. (NEDO)

Investigation on the development and introduction of new geothermal exploration technology. Part 2; Chinetsu shintansa gijutsu kaihatsu donyu ni kansuru chosa. 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-02-01

For the purpose of maintaining and increasing the geothermal power generation amount, the development was made of exploration technologies which become necessary in the stage of geothermal reservoir exploration and in the stage of reservoir management and peripheral development. As development technologies, the following were proposed: fracture flow characteristics exploration method (FE), production/circumference areas flow characteristics exploration method (PE), and integrated analyzing method (IA). As to FE, for the survey of geothermal fluid dynamic characteristics in fracture aggregate composing the geothermal reservoir, developments were made of the well hydraulic testing method for examining hydraulic characteristics of fracture system and of the fracture evaluation method composed of the core/logging analysis method, the permeability logging method and electroseismic exploration method. As to PE, for maintaining and managing steam production in the developmental area and developing the area to the circumference area, development was conducted of technology for exploring variations of reservoirs and fluid flow from the data on precision gravity, three-dimensional resistivity, fluid geochemistry, active seismic wave and self potential, precision electromagnetism, passive seismic wave, etc. As to IA, development was made of reservoir simulation technique, etc. 2 refs., 70 figs., 41 tabs.

Design of photovoltaic generation systems for lean-to greenhouses; Katayane onshitsuyo taiyoko hatsuden system no sekkei

Energy Technology Data Exchange (ETDEWEB)

He, D; Kozai, T [Chiba University, Chiba (Japan). Horticulture Faculty

1997-11-25

Outlined herein are characteristics of solar radiation permeation in lean-to greenhouses provided with photovoltaic (PV) arrays on part of their roofs, and estimated quantities of power generated by the PV systems for different districts, seasons and cell areas. Three types of PV systems were followed; system 1: single-crystalline silicon, system 2: amorphous silicon, monolithically combined with the roof, and system 3: film-shape amorphous silicon. Annual quantity of power generated by these systems tends to increase as latitude decreases. They show an annual energy conversion efficiency of 10.3, 5.1 and 2.1%, respectively. Efficiency is unaffected by direction of the building on which the PV system is installed at low latitudes, as long as it is within {+-} 30deg around the east-west direction. At high latitudes, it is preferably in the east-west direction. For the PV system covering 30% of the roof area at a north latitude of 35deg, light received by plants in the greenhouse is fairly unaffected by the system throughout the year. These systems show a yearly solar energy utilization efficiency of 49 to 59, 46 to 55 and 44 to 53%, respectively, when they cover 60% of the roof area. 5 refs., 6 figs, 2 tabs.

Molten carbonate fuel cell power generation system. Yoyu tansan prime en gata nenryo denchi hatsuden sochi

Energy Technology Data Exchange (ETDEWEB)

Uematsu, K; Hatori, S [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan)

1991-11-01

In an indirect internal reforming type molten carbonate fuel cell, the reforming temperature is limited less than the operating temperature of the fuel cell, as the heat source for reforming is depended on the reaction heat at about 650 {degree} C of the fuel cell. To improve the reforming rate at the low temperature range, it is considered to increase S/C (ratio of steam to carbon), but this scheme will cause such problems as to increase the voltage drop of the anode, to drop the heat recovery ratio on the cogenerator, to increase the capacity of the heat exchanger, etc. In this invention, in the power generating plant of a molten carbonate fuel cell the inert gas is added to the reforming raw gas, and in addition to the above the gas is mixed with steam and led into the reforming chamber of the plant. When the inert gas which is not directly concerned in the reforming reaction is added to, total mol number increases and the reforming reaction is acceralated. Consequently, the reforming rate can be raised, though the reforming temperature is low. 2 figs.

Performance analysis in Japanese field test program; Field test data kara no chiiki hatsuden kaiseki hoho

Energy Technology Data Exchange (ETDEWEB)

Sugiyama, H.; Kurokawa, K.; Uchida, D. [Tokyo University of Agriculture and Technology, Tokyo (Japan); Otani, K.; Sakuta, K.; Tsuda, I. [Electrotechnical Laboratory, Tsukuba (Japan); Oshiro, T.; Sakamoto, K. [Japan Quality Assurance Organization, Tokyo (Japan)

1997-11-25

Power generation characteristics are investigated using data collected in photovoltaic power generation field tests being undertaken by NEDO (New Energy and Industrial Technology Development Organization). The photovoltaic power generation system performance is evaluated by examining loss factors leading to degradation in system performance, with weather conditions such as variation in insolation and air temperature, inverter performance, and shadows cast by surrounding buildings taken into consideration. As the result, it is found that the important loss factors are degradation in module performance due to elevated temperature, drift in the maximum output control, degraded inverter performance due to input power variation, effect of shadows, etc. It is learned that system is greatly affected by degradation in module performance due to increased temperature in summer and by shadows in winter, the two being responsible for the output coefficient dropping to approximately 75% throughout the year. The output coefficient frequency distribution charts for the 75 test sites confirm that the rate is as low as 70-80% at many sites. As for the system operating time, it tends to be longer in West Japan where the annual insolation rate is higher. 3 refs., 10 figs.

Studies on the utilization of inedible parts produced at processing the marine products. Part 1; Suisan haikibutsu no kodo riyo ni kansuru kenkyu. 1

Energy Technology Data Exchange (ETDEWEB)

Kitamura, S.; Nomura, A.; Quinones, H. [Industrial Technology Center of Kochi Prefecture, Kochi (Japan)

1995-09-01

For the purpose of effectively using marine products in Kochi pref., analyses were made of the components of the following marine products: the head and inside of frigate mackerel disposed of at the time of producing dried frigate mackerel (an annual catch of the frigate mackerel is about 12000-15000 tons, almost half of which is used for processing for dried bonito), the head and other part of lobster disposed of at lobster restaurants (including the shell of lobster), the skin of lazard fish disposed of in boiled fish paste producing plants. The analysis was conducted in terms of the composition of coarse fatty and fatty acid, free amino acid, ATP related compounds, etc. As a result, the following were found out: in the fat of the head and inside of frigate mackerel, DHA (docosahexaenoic acid) and EPA (eicosapentaenoic acid) were included by 20-30% and 10%, respectively, and the fat is promising as supply source of high-grade unsaturated fatty acid; in the head and other part of lobster, chitin chitosan is included in addition to free amino acid such as glycine and alanine; in the skin of lazard fish, ATP related compounds such as inosinic acid are included, and the skin is useful for a raw material of the seasoning. 15 refs., 4 figs., 6 tabs.

Evaluation report on the R and D of the membrane separation process introduction technology; Makubunri process donyu gijutsu no kenkyu kaihatsu hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper reported the R and D of the membrane separation process introduction technology during a period of 1994 through 1998. The membrane separation technology is not associated with the phase change which requires large energy and expected to be an energy saving process. For the production of membranes required of high functions, the vapor deposition polymerization method was considered, and high order structure control of the membrane, control of adhesion and attachment, and control of orientation, and development of the high polymerization technology were required. For the high grade control of vapor polymerization, the substrate surface structure/quality were important. The molecular level analysis of the vapor deposition surface was also needed. Therefore, the paper took notice of STM (scanning tunneling microscopy), AFM (atomic force microscopy) and HREELS (high resolution electron energy loss spectroscopy) as surface atomic/molecular configuration analysis technology, and designed/fabricated and studied the high resolving power and high sensitivity analysis equipment using the analysis equipment which combined HREELS and STM and the analysis equipment using SFG (sum frequency generation) which can detect signals in the low frequency region. Making full use of the highest technology, technology was able to be developed for substrate surface analysis and surface reaction analysis technologies which become the basis of the high performance separation membrane fabrication technology by the vapor deposition polymerization method indispensable for introduction of the membrane separation process. The technology can be the base applicable to a lot of fields where surfaces and interfaces are concerned

FY 1998 Report on development of large-scale wind power generation systems. Feasibility study on development of new technologies for wind power generation (Study on the development of wind power generation systems for small-scale power grids); 1998 nendo ogata furyoku hatsuden system kaihatsu seika hokokusho. Furyoku hatsuden shingijutsu kaihatsu kanosei chosa (shokibo keito ni okeru furyoku hatsuden system ni kansuru chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This survey includes the characteristics of small-scale power grids, feasibility studies on introduction of wind turbines in these grids, and statuses of application of wind turbines to isolated islands or the like in the advanced countries, in order to promote introduction of wind power generation systems in isolated islands or the like. It is concluded that small-capacity wind power generation systems can be possibly introduced in the intermediate- to large-scale grids in isolated islands, 1,500kW or larger in capacity, in the Tokyo, Kyushu and Okinawa Electric Power Companies' areas. A scheduled steamer ship for isolated islands can carry up to 10 ton track, and introduction of a small-scale wind turbine is more advantageous viewed from the transportation cost. Some foreign countries have the sites which have achieved a high percentage of grid connection of wind power units by stabilizing wind conditions and connecting them to the main high-voltage grids in different manners from those adopted in Japan. For developing wind turbine bodies, most of the foreign countries surveyed are concentrating their efforts on development and manufacture of large-size units, paying little attention on development of small-size wind turbines for isolated islands. For the future prospects, the promising concepts include adoption of wind turbines small in capacity and easy to transport and assemble, and hybrid systems combined with power storage units. (NEDO)

FY 1998 Report on development of large-scale wind power generation systems. Feasibility study on development of new technologies for wind power generation (Study on the development of wind power generation systems for small-scale power grids); 1998 nendo ogata furyoku hatsuden system kaihatsu seika hokokusho. Furyoku hatsuden shingijutsu kaihatsu kanosei chosa (shokibo keito ni okeru furyoku hatsuden system ni kansuru chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This survey includes the characteristics of small-scale power grids, feasibility studies on introduction of wind turbines in these grids, and statuses of application of wind turbines to isolated islands or the like in the advanced countries, in order to promote introduction of wind power generation systems in isolated islands or the like. It is concluded that small-capacity wind power generation systems can be possibly introduced in the intermediate- to large-scale grids in isolated islands, 1,500kW or larger in capacity, in the Tokyo, Kyushu and Okinawa Electric Power Companies' areas. A scheduled steamer ship for isolated islands can carry up to 10 ton track, and introduction of a small-scale wind turbine is more advantageous viewed from the transportation cost. Some foreign countries have the sites which have achieved a high percentage of grid connection of wind power units by stabilizing wind conditions and connecting them to the main high-voltage grids in different manners from those adopted in Japan. For developing wind turbine bodies, most of the foreign countries surveyed are concentrating their efforts on development and manufacture of large-size units, paying little attention on development of small-size wind turbines for isolated islands. For the future prospects, the promising concepts include adoption of wind turbines small in capacity and easy to transport and assemble, and hybrid systems combined with power storage units. (NEDO)

Marketing research on potential demands of photovoltaic systems. Taiyoko hatsuden system no senzai shijo chosa seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

1988-03-01

Applicable uses and the market size for photovoltaic (PV) systems were investigated taking into consideration the features and economics of such systems. As a result of computing representative usage examples together with the extent of potential demand for PV, 238 GW for the power source in private homes, 76 GW for green houses, 126 GW for sewage water treatment plants, 4 GW for schools and universities and others were estimated. For the greater number of PV systems already in actual use, non-cost factors acted as major determining factors when deciding on implementation. Promising uses (applicable ideas) seen from the standpoint of non-cost factors were studied in order to develop the PV system market and gain breakthrough for lowering future costs and increasing proliferation for such systems. When it comes to simultaneously decreasing costs and increasing demand for solar batteries in the coming days, it will be impossible to make an immediate transition from the present state of demand for public use and for special use to the final goal of demand as a power source in the home. There is a need for an intermediate demand that can bridge this gap. (13 figs, 9 tabs)

Arrangement of technical information on photovoltaic power generation systems; Taiyoko hatsuden system kanren gijutsu joho no seibi

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

In order to effectively contribute to the development of the technology required to put them to practical use, technical information on photovoltaic power generation systems, such as the results of overseas and domestic research and development work, which have been obtained by NEDO, were collected, categorized, sorted, and processed to make a data base. This report presents the details of the project for fiscal 1995. Papers from the 10th ECPVSEC held at Lisbon, Portugal in April 1991 and the 6th PVSEC held at New Delhi, India in February 1992, and papers published by NEDO were investigated and arranged. The total number of the papers processed in 1995 is 424 from two international conferences, and 176 from NEDO. The implementation steps consist of the collection of overseas and domestic research reports and other documents, the preparation of summaries of research results reported in those documents, the preparation of brief summaries of data obtained from the results of experiments including numerical data, and the sort and processing of them by research area, material used to fabricate photovoltaic cells, etc. The results of the above work are stored on 3.5 inch floppy disks as MS-DOS text data. The report also provides the general publication through the Internet. 7 tabs.

Fiscal 1981 Sunshine Project research report. Development of hydrothermal power plant. Development of binary cycle power plant. Conceptual plant design; 1981 nendo nessui riyo hatsuden plant no kaihatsu / binary cycle hatsuden plant no kaihatsu seika hokokusho . Plant gainen sekkei

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Conceptual design was made on a 10MW class binary cycle power plant for a demonstration plant superior in reliability and profitability, under most realistic current geothermal field conditions. In the design, study was made on heat balance, main pipe system, equipment allocation, and electric system for a plant system configuration, and study was also made on preheater, evaporator, condenser, turbine and others for plant component equipment. Further study was made on optimization of mist cooling condenser, instrumentation, control, utility, and environmental measures. The following basic data were obtained through the conceptual design: plant inlet hot water temperature: 130 degrees C, plant outlet hot water temperature: 70 degrees C, hot water flow rate: 1,415t/h, working fluid: R-114, R-114 pressure in evaporator: 11.98kg/cm{sup 2} abs, R-114 evaporation temperature: 91.1 degrees C, R-114 condensation temperature: 31.0 degrees C, R- 114 flow rate: 2,265t/h, site area: 106.5m x 102.4m, building area: 48.7m x 16.8m, and building height: 13.0m. (NEDO)

FY 1998 Report on development of large-scale wind power generation systems. Research on the future prospects of wind power generation systems; 1998 nendo ogata furyoku hatsuden system kaihatsu. Furyoku hatsuden system no shorai tenbo ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Current status of wind power generation in Japan and situations in foreign countries ahead of Japan are surveyed, in order to clarify the prospects for the future diffusion and expansion of wind power generation systems in Japan. The surveyed trends of wind power generation in Japan include those related to mandatory laws and regulations, e.g., the Electricity Enterprises Act, introductory and operation situations in local autonomies and electric power companies, and R and D efforts by academic and research organizations. The surveyed wind power generation situations in foreign countries include trends of international standardization for wind power generation, and global situations of introducing these systems. The on-the-spot oversea surveys include location/wind conditions in Greece's islands, cyclone-caused damages in India, World Renewable Energy Congress in Perth and advanced technologies in Europe for wind power generation systems, and the survey results are reported in detail. The surveyed R and D projects in Japan include the basic technological R and D plans (draft) for, e.g., wind power generation systems for isolated islands. (NEDO)

Study on low permeable backfill materials. Backfill materials for waste disposal facilities; Koshisuisei juten zairyo ni kansuru kenkyu. Hoshasei haikibutsu shobun shisetsu eno tekiyosei kenkyu

Energy Technology Data Exchange (ETDEWEB)

Shiraishi, F; Konishi, M; Shiraishi, H [Okumura Corp., Osaka (Japan)

1994-11-15

A discussion was given on the fundamental properties of mortar made from cement mixed with silica fume. Four kinds of silica fumes with different particle size distributions were used. The following results were obtained: distribution of pores in mortar admixed with silica fume shifts to the smaller radius side; while the admixture increases the compression strength in mortar, the increasing trend varies depending on the kinds of silica fumes; this is thought to be caused from the difference in pozzolan activity between silica fumes; and the strength increase is caused by densification of the structure due to the pozzolan reaction that is generated after hydration, or in other words, decrease in the pore volume. The applicability of the mortar was investigated as a filling mortar to fill up clearances between wastes. It was found that the filling performance can be controlled by mixing silica fume at an adequate level and adjusting the viscosity. The diffusion coefficient for the admixed concrete is smaller by 30% to one digit than that for the ordinary concrete. High-performance water stopping concrete of 0.11 {times} 10{sup 4}cm {sup 2}/s at maximum was obtained. The concrete can be regarded as a material having superb filling and water stopping performances. 6 refs., 4 figs., 5 tabs.

FY 1998 Report on development of large-scale wind power generation systems. Part 2. Operational research on large-scale wind power generation systems; 1998 nendo ogata furyoku hatsuden system kaihatsu seika hokokusho. 2. Ogata furyoku hatsuden system no unten kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The on-the-spot surveys are conducted and related information is collected for current status of wind power generators connected to power grid systems and simulation techniques therefor in the USA and European countries. In Denmark, the grid system to which wind power generators are connected is a 10kV radiation type system, by which these generators are connected to general consumers. Power quality is investigated by the programs developed by DEFU (Danske Elvarkers Forening Udredning). The German's Norderland Wind Park has the largest capacity in Europe with 35 units of 1.5MW generators. They are connected to a 110kV grind system via ISOREE to control disturbances to the commercial grid system. The USA, used to have the world largest wind power generation capacity, is now plays second fiddle to Germany whose capacity has now exceeded 2,000MW. The country is now seeing the second rush for construction of wind power generators, planning to have a new capacity of 570MW in 1998. Information is also collected from other countries or organizations, including the Netherlands, WREC, Italy and Spain. (NEDO)

FY 1998 Report on development of large-scale wind power generation systems. Part 2. Operational research on large-scale wind power generation systems; 1998 nendo ogata furyoku hatsuden system kaihatsu seika hokokusho. 2. Ogata furyoku hatsuden system no unten kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The on-the-spot surveys are conducted and related information is collected for current status of wind power generators connected to power grid systems and simulation techniques therefor in the USA and European countries. In Denmark, the grid system to which wind power generators are connected is a 10kV radiation type system, by which these generators are connected to general consumers. Power quality is investigated by the programs developed by DEFU (Danske Elvarkers Forening Udredning). The German's Norderland Wind Park has the largest capacity in Europe with 35 units of 1.5MW generators. They are connected to a 110kV grind system via ISOREE to control disturbances to the commercial grid system. The USA, used to have the world largest wind power generation capacity, is now plays second fiddle to Germany whose capacity has now exceeded 2,000MW. The country is now seeing the second rush for construction of wind power generators, planning to have a new capacity of 570MW in 1998. Information is also collected from other countries or organizations, including the Netherlands, WREC, Italy and Spain. (NEDO)

FY 1998 Report on development of large-scale wind power generation systems. Part 1. Operational research on large-scale wind power generation systems; 1998 nendo ogata furyoku hatsuden system kaihatsu seika hokokusho. 1. Ogata furyoku hatsuden system no unten kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The research and development project is implemented for large-scale wind power generation systems, and the FY 1998 results are reported. In the FY 1998, a slip property variable generator is actually mounted on the wind power generator, to conduct various types of demonstration tests. The reliability validation tests include microstructure examinations, fatigue tests and fatigue strength tests to predict residual strength in the blade. It is confirmed that the blade has a sufficient residual strength. The performance validation tests include continuous measurement of power outputs and wind velocities, and analysis of the output fluctuations. The power output performance during winter when the west wind prevails is higher than designed. In the tests for evaluating the characteristics of the system on which a slip property variable generator is mounted, the output smoothing effect is confirmed in a range beyond the rated output. The wind power generation system is continuously operated, to accumulate the operational data for, e.g., capacity factor, operating time rate, and system failure status. The FY 1998 results are 920,000kWh as the output and 21% as capacity factor. The other items investigate include aerodynamic noise reduction countermeasures, fatigue life of the wind turbine blades, economics of wind power generation, and dismantling and reuse of the wind turbines. (NEDO)

FY 2001 report on the results of the survey of the formation promotion subsidy project on the environmentally friendly type energy community. Survey of the commercialization of high efficiency power generation using fuel of waste such as waste construction materials; 2001 nendo kankyo chowa gata energy komyuniti keisei sokushin hojo jigyo. Kensetsu haizai tou haikibutsu nenryo ni yoru kokoritsu hatsuden no jigyosei chosa chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

The paper studied a system for power generation and heat utilization using wood chips such as waste construction materials, used paper inappropriate for recycling and plastic refuse from neighboring local governments as fuel and assessed a potentiality of the commercialization. As to the system, the following were conducted: selection of the optimum combustor in the waste power generation, survey of the state of corrosion of boiler tube in the steam conditions and waste properties, selection of the optimum quality of boiler materials, etc. In the assessment of a potentiality of the commercialization, the commercialization was studied as in-house power generation/heat utilization business with a power generation scale of 9,950kW and a steam supply scale of 31.5t/h. As a result of the study, the energy conservation effect was found to be expected as follows: reduction of 33,000kL/y crude oil equivalent and reduction of 16,000t-CO2/y emission. As a result of studying the economical efficiency of business, the unit price of wood chip purchase and the unit price of waste plastic treatment which are required to recover the difference of the initial investment within 5 years were greatly different from the level as an aim. For the realization as business, a subsidy of 15% and more cost reduction were requested. (NEDO)

Outline of fiscal 1967 achievements in research on MHD power generation; 1967 nendo MHD hatsuden kenkyu seika gaiyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1968-09-01

Compiled are the results of studies conducted in fiscal 1967 on MHD (magnetohydrodynamic) power generation. In the test operation and modification of a 1,000kW-class MHD power generator at the Electrical Research Laboratory, a test is conducted using Faraday-type electrodes. It is then found that this configuration results in a maximum output of approximately 700kW, which is less than expected. In the experimental construction at the Hitachi, Ltd., of a machine capable of a long-term operation, an MHD power generator is built for a continuous operation of 100 hours with an maximum output of 2kW, and a 110-hour power generation is successfully achieved with a maximum output of 1.9kW. In the research and development of heat exchangers, tests are conducted for a bulkhead type heat exchanger, heat accumulator type heat exchanger, molten slag type heat exchanger, and a gas/liquid 2-phase flow type heat exchanger. In the study of heat-resisting insulators, materials based on zirconate, magnesia, thoria, zirconia, etc., are tested. In addition, studies are conducted on electrode materials, superconductive electromagnets (small superconductive electromagnets for MHD power generators, turbine type helium liquefiers, superconductive wires for 70-kilogauss electromagnets, etc.), and thermal performance rating. (NEDO)

Outline of fiscal 1970 achievements in research on MHD power generation; 1970 nendo MHD hatsuden kenkyu seika gaiyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1970-07-01

Compiled are the results of studies conducted in fiscal 1970 on MHD (magnetohydrodynamic) power generation. In the operation test and modification of the 1000kW-class MHD power generator, modification is carried out involving the combustion system, seed collecting method, and power generation channel, and reviews through experiments are conducted about the analysis and control of the boundary layer structure. In the operation test of the MHD power generator designed for prolonged operation, a test operation for resistance to heat and seeds continues more than 100 hours using a cold wall type power generation channel constituted of water cooled ceramics, and the ceramics are analyzed for failure and loss. Studies are also conducted involving MHD power generator heat exchangers, seed collecting methods, electrode materials for MHD power generators, heat-resistant materials for MHD power generators, thermal performance rating for MHD power plants, etc. In the research and development of superconductive electromagnets, superconductive electromagnets are developed and tested for 1000kW-class MHD power generators, and studies are conducted on turbine type helium liquefiers, superinsulated superconductive electromagnetic field generators, etc. (NEDO)

Report on results of contract research. 'Research on MHD generation system'; MHD hatsuden system no kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

'Research on MHD generation system' was implemented by its expert committee in the electric joint study group, with the results of fiscal 1980 reported. This year, a detailed conceptual design was carried out on a coal fired MHD generation system, with points for the technological development concretely examined. In addition, investigation was conducted on the progress of MHD generation technology, development situation of other generation systems, state of energy resources, etc., in various foreign countries. In the conceptual design of the coal fired MHD generation plant, the system structure of a 2,000 MWt class commercial MHD generation plant was explained, as were the conceptual design of the structural elements and proposals for a 500 MWt class demonstration plant and an 100 MWt class experimental plant, for example. In the overseas trend of R and D on MHD generation, investigations were made concerning the U.S., Soviet Union, and China, with details compiled for such items as generation plants, combustors, generation channels, heat resisting materials, superconducting magnets, heat exchangers, seed slags, inverters, boilers and environments, and commercial plants. (NEDO)

Outline of fiscal 1969 achievements in research on MHD power generation; 1969 nendo MHD hatsuden kenkyu seika gaiyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1969-07-01

Compiled are the results of studies conducted in fiscal 1969 on MHD (magnetohydrodynamic) power generation. In the operation test and modification of the 1,000kW-class MHD power generator, the operation test continues from the preceding fiscal year using high-temperature air as oxidant, and the growth of boundary layer in the channel is determined. In the operation test of the MHD power generator designed for prolonged operation, insulation walls, electrode materials, and structures capable of prolonged operation are developed and tested. In the research of MHD power generator heat exchangers, studies are made about the bulkhead type and heat accumulator types (stationary type, rotary type, and falling-grain type). In addition, studies are conducted about seed collecting methods, MHD power generator electrode materials, heat-resisting insulators, and thermal performance rating. In the research and development of superconductive electromagnets, studies are conducted about superconductive electromagnets for 1kW MHD power generators, ferromagnetic superconductive electromagnets for 1,000kW-class MHD power generators, 45-kilogauss col type superconductive electromagnets, turbine type helium liquefier, high current density col type superconductive electromagnets, superinsulated magnetic field generators, etc. (NEDO)

Report on results of contract research. 'Research on MHD generation system'; MHD hatsuden system no kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

'Research on MHD generation system' was implemented by its expert committee in the electric joint study group, with the results of fiscal 1981 reported. This year, technological reexamination was conducted for a 2,000 MWt commercial MHD generation plant, with evaluation carried out on the cost performance including the construction and operation cost. In addition, for the purpose of intermediate R and D towards the practicability, examination was also conducted on a system structure, concrete specifications of component element, cost of R and D including operation expenses for example, concerning an 100 MWt class experimental plant and a 500 MWt class plant. In the investigation of the overseas trend, information was summarized in detail on the experimental devices, combustors, generation channels, electrode materials, electrode phenomena, theoretical analyses, seeds, slag, component equipment, instrumental technologies, conceptual designs of generation plant, commercial plant, etc., in Soviet Union, China, Holland, India and EPRI, on the basis of the materials from the 19th MHD symposium held in UTSI and from the coal MHD specialist conference held in Sydney. (NEDO)

Report on results of contract research. 'Research on MHD generation system'; MHD hatsuden system no kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-03-01

'Research on MHD generation system' was implemented by its expert committee in the electric joint study group, with the results of fiscal 1982 reported. This year is the final year of this research; therefore, reexamination was made from the practical standpoint on the R and D of coal fired MHD generation, evaluating the present technological level as well as clarifying the development procedures, with proposals made as to the R and D from now on. The present technological level in the practicability is still in the basic stage, where the essential problem is the development of combustors, air heaters and generation channels in particular. An examination was conducted for the problems, procedures and period of the development for each component equipment, with the results provided as materials for studying the path to the experimental plant of 100 MW heat input. In the method of proceeding with the R and D in the future, it was decided as essential, in order to enter the stage of the experimental plant from the element technology development, that R and D is carried out on the unestablished component technology, making sure that no excessive risk is taken in scaling up to the next stage. (NEDO)

Performance analysis of dish solar stirling power system; Stirling engine wo mochiita taiyonetsu hatsuden system no seino yosoku

Energy Technology Data Exchange (ETDEWEB)

Tsuchiya, K; Yamaguchi, I [Meiji University, Tokyo (Japan); Naito, Y; Momose, Y [Aisin Seiki Co. Ltd., Aichi (Japan)

1996-10-27

In order to estimate the performance of the dish solar Stirling power system, matching and control of each component system were studied, and the performance of the 25kWe class power system was estimated on the basis of direct solar radiation measured in Miyako island, Okinawa. Application of a Stirling engine to solar heat power generation is highly effective in spite of its small scale. The total system is composed of a converging system, heat receiver, engine/generator system and control system. As the simulation result, the generator output is nearly proportional to direct solar radiation, and the system efficiency approaches to a certain constant value with an increase in direct solar radiation. As accumulated solar radiation is large, the influence of slope error of the converging mirror is comparatively small. The optimum aperture opening ratio of the heat receiver determined on the basis of mean direct solar radiation (accumulated solar radiation/{Delta}t (simulated operation time of the system)), corresponds to the primary approximation of the opening ratio for a maximum total generated output under variable direct solar radiation. 6 refs., 6 figs., 1 tab.

Soft switching buck-boost converter for photovoltaic power generation; Taiyoko hatsuden no tame no soft switching shokoatsu converter

Energy Technology Data Exchange (ETDEWEB)

Lee, H. [Kyungnam University (Korea, Republic of)

1996-10-27

A soft switching method with small switching loss was proposed for the purpose of increasing the efficiency of a DC-DC boost converter which converted a DC current generated by solar cells to a variable DC current. Existing current converters are supplemented by using a snubber circuit around the switch so as to protect the switch by a hard switching action. However, with an increase of the output current, snubber loss is increased, reducing the efficiency. In order to solve this problem, the partial resonant switch method was applied to the converter; with this method of partially forming a resonant circuit only at the time of turning on/off of the switch, the switching loss was reduced through the soft switching, thereby making the proposed converter operate with high efficiency. Moreover, the resonant element of the partial resonant circuit using a snubber condenser, the energy accumulated in the condenser was regenerated on the power supply side without loss of snubber. With the regenerated energy, the proposed converter was provided with a smaller ratio of switching to use than the conventional converter. 4 refs., 7 figs., 1 tab.

Report on achievements in fiscal 1998. Development of technologies to put photovoltaic power generation systems into practical use - Research and development of solar beam power generation and utilization systems and ancillary technologies (Investigations and researches on evaluations of photovoltaic power generation); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (taiyoko hatsuden hyoka no chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Values given to global environment and economy by utilization of photovoltaic power generation are evaluated, and quantified to make clear the significance of the utilization thereof. Specifically, trial calculations were performed on LCA and damaging characteristics of photovoltaic systems, and reducible amount of carbon dioxide emission. Taking up thin film CdTe cells as the object, estimation was made on the energy payback time (EPT) and CO2 emission amount. The production scale ranges over 10 MW/ 30 MW/ 100 MW annually, the useful life is 20 years, and the unit requirement for CO2 emission originated from the charged electric power is 114 g-C/kWh. The EPT was 1.74 in the annual production of 10 MWp, 1.08 in 100 MWp, the unit requirement for CO2 emission was 14.0 in the annual production of 10 MWp, and 8.9 in 100 MWp. This is one of severals of that in the existing power supply source. For heavy metals, particularly Pb, the trial calculation resulted in 0.15 g/Wp in the crystalline type, and 0.1 g/Wp in the amorphous type. The problem therewith is separation and recovery. The reducible amount of carbon dioxide, or in other words, the amount of power that can be generated latently is 37,235 GWh/year, or 3.10 million tons when converted into carbon dioxide. (NEDO)

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Research and development of photovoltaic system evaluation technology (Research and development of system evaluation technology - Photovoltaic system data book, separate volume); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu (system hyoka gijutsu no kenkyu kaihatsu bessatsu (taiyoko hatsuden system data shu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In the research and development of photovoltaic power generation system evaluation technology, great progress has been achieved in performance improvement and cost reduction as far as constituent devices such as power modules and inverters are concerned. In the designing of systems, however, quantitative elucidation of loss and power reduction factors remains insufficient. Under the circumstances, several types of photovoltaic power generation systems expected to be put to practical application in the future are taken up, test facilities are constructed which simulate them, and data are collected. The thus-collected data are utilized for research and development of evaluation techniques necessary for the improvement of photovoltaic system efficiency, such as design parameter quantification, databasing and utilization thereof, and simulation technologies, for the establishment of technologies for optimum designs and optimum operations. The data book accommodates data, arranged in an easy-to-use fashion, collected about verification test facility (interconnected systems, independent systems, and water pump systems) operation, weather conditions, and residential photovoltaic power generation systems. (NEDO)

Experimental study on the effective utilization of combusted scallop cultivation waste. Hotate yoshoku haikibutsu no yuko riyo no tame no shokyaku shori joken no jikkenteki kenkyu

Energy Technology Data Exchange (ETDEWEB)

Hase, Y [The Tohoku Electric Power Co. Inc., Sendai (Japan)

1993-06-15

Discussions are given on treatment methods that can utilize scallop cultivation wastes effectively. Tests to incinerate and convert the main scallop shell content, calcium carbonate, into calcium oxide (CaO) discovered optimal incinerating conditions of a temperature at 750[degree]C and a duration for 30 minutes, and 700[degree]C and one hour. CaO content in burnt shells was so high that they could be used as a raw material for quick lime. In the incineration and conversion tests on wastes from shell processing factories, the result of X-ray diffraction in chemically combined conditions of inorganics before and after the incineration revealed that the main component Ca existed as CaCO3, which may be converted into CaO when incinerated. The result also showed that the second component, Mg, existed as MgO after the incineration. From the above results, incinerating the wastes from shell processing factories at 750[degree]C would be capable of incinerating organic components completely and reducing their weights. Because the inorganic residues have high CaO content, they could be utilized effectively as a quick lime raw material. Although shells to be incinerated have low salt content because of having been boiled, salt content in scallop processing factory wastes will require discussions on possibilities of its corroding an incineration furnace. 3 figs., 7 tabs.

Technical surveys on MHD combustors. Surveys on incorporation of pressurized coal partial combustion furnaces; MHD combustor gijutsu chosa. Kaatsugata sekitan bubun nenshoro no donyu chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-03-01

The pressurized coal partial combustion (PCPC) furnace is surveyed/studied for its incorporation in MHD generation. The technical development of the atmospheric CPC has been basically completed, and the concept is demonstrated using a test system of commercial size. Many techniques developed for the atmospheric CPC are applicable to the PCPC system. These include structures of the CPC furnace walls, and slag handling and simulation techniques. Combination of PFBC with PCPC or IGCC can bring about many merits, e.g., enhanced efficiency and abated NOx emissions for the combined cycle power generation. These topping cycles, therefore, should be developed in the early stage. MHD power generation is one of the concepts that can enhance efficiency. In particular, the techniques for closed cycle MHD generation have notably advanced recently. The PCPC techniques are useful for coal combustors for MHD generation. Full-scale development works for the direct coal combustion gas turbine systems have been just started for the IGCC systems of the next generation, and the PCPC-related techniques are expected to serve as the central techniques for these turbine systems. (NEDO)

New energy vision for Oita Prefecture. Toward the adoption of eco-energy; 2001 nendo Oita ken shin energy vision. Eco energy no donyu ni mukete

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

For contributing to the preservation of the global environment, studies were made to work out a new energy introduction vision fully exploiting the characteristic features of Oita Prefecture. Oita Prefecture's demand for energy in 1998 is estimated to be 408.6 times 10{sup 15} J, with coal-based energy covering 204,016 TJ, oil-based energy 160,192 TJ, electric power 37,721 TJ, and so forth. The consumption will result in the emission of 35.77 million tons of carbon dioxide. According to Oita Prefecture's prospect of its eco-energy adoption in 2010, there will be 319 MW from hydroelectric power, 155 MW from geothermal power, 52 MW from photovoltaic power, 46 MW from clean energy vehicles, 33 MW from refuse-fueled power, and so forth. To prepare plans for facilities to utilize eco-energy and for regional development in the future through the use of such facilities, introduction costs were predicted and effects were simulated for model businesses engaged in biomass power generation using livestock wastes, small-scale hydroelectric power generation, bio-diesel fuel production, wind power generation, and woody biomass power generation. (NEDO)

Development of hot water utilizing power plant in fiscal 1999. Development of binary cycle power plant (Development of 10-MW class plant); 1999 nendo nessui riyo hatsuden plant to kaihatsu. Binary cycle hatsuden plant no kaihatsu (10MW kyu plant no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With an objective to utilize effectively middle to high temperature hot water type geothermal resources, R and D has been performed on a downhole pump-applied binary cycle power plant which exchanges heat energy with a secondary media in a heat exchanger, and generates electric power. This paper summarizes the achievements in fiscal 1999. This fiscal year has installed an operation control device and made partial modification therein for the hot water system testing device installed in the previous fiscal year, which was followed by test operation. Having been performed in addition were the installation of cooling water collection pumps, improvement of water storage tanks, modification of piping for injection of downhole pump cooling water, inspection of high-temperature cooling device and low-temperature cooling device, and discussions on deposits onto the downhole pumps. Furthermore, an environmental impact survey has performed measurements of precipitation, river flow rates, thermal spring, spring water, noise, and groundwater fluctuation. A survey was also carried out on transplantation of precious plants. In the single and overall test operation of the hot water system testing device, normal operation was identified. However, the operation had to be suspended because of a trouble in the downhole pump. (NEDO)

Research on PV system application on residences. Part 1. Report on the systems and PV measurement results of an experimental passive solar house; Taiyoko hatsuden system no jutaku eno oyo ni kansuru kenkyu. 1. Taisho tatemono taiyo to taiyoko hatsuden system keisoku kekka

Energy Technology Data Exchange (ETDEWEB)

Ishihara, O.; Sakai, K.; Hirakawa, M. [Kumamoto University, Kumamoto (Japan). Faculty of Engineering

1997-11-25

System of the house is outlined, and warming performance and photovoltaic power generation system energy performance are taken up. It is a one-storied meeting hall situated in an apartment area, whose heat loss factor is 2.59kcal/m2hdegC. Ninety hybrid solar cells provided with circulating air heat collectors are installed on the east-side of the roof, interconnected to the commercial power system. In the daytime in summer, the house is fully insulated from solar radiation, with the room temperature kept a little lower than the open air temperature. The range of daily change in the room temperature is narrow, providing a comfortable residential space. When the windows are opened in the evening, cool air comes into the room to replace the warm air inside, reducing the difference in temperature between the inside and outside of the room. In winter, insolation time is short on the east side of the roof which finds itself out of the sun. Under the circumstances, the system outputs but a little and the quantity sold is quite small in winter. But, in summer, sale of power can be practicable, thanks to exposure to sufficient sunshine. The inverter rated at 3.5kW attains a 90% or higher operating rate in the presence of an input of power of 0.5kW or more. 4 refs., 10 figs.

Fiscal 1997 development of the geothermal water use power plant, etc. Development of the binary cycle power plant (10MW class plant); 1997 nendo nessui riyo hatsuden plant nado kaihatsu. Binary cycle hatsuden plant no kaihatsu (10MW kyu plant no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

A R and D was conducted with the aim of using medium-/high-temperature hot water type geothermal resources. In fiscal 1997, fabrication of geothermal water system testing equipment and geothermal water production/reduction piping installation work were conducted, and an environmental effect survey and ground water variation observation were carried out. Moreover, pumps to pump up geothermal water were fabricated. In the fabrication of a pump for No. 3 demonstration plant, the following improvements were made. Concerning the inlet undersea bearing, the shapes related to it were so reformed that external water feeding in the initial run can be done. Relating to the protection of the thrust bearing half load side friction face, a spring was added to the face so that it was structured to give preload. As a method to install a casing covering board, adopted was a band installation method which is easy in handling. The number of instrumentation cables was reduced. As to cables for downhole pumps, studied were methods of connection, etc. of connection portions of the motor connector and instrumentation cable. Moreover, purifying/regeneration facilities of the downhole pump bearing oil were fabricated and tested. 85 figs., 57 tabs.

Fiscal 1980 Sunshine Project research report. Development of hydrothermal power plant (Development of binary cycle power plant). Supplement. Research on plant technology; 1980 nendo nessui riyo hatsuden plant no kaihatsu seika hokokusho. Binary cycle hatsuden palnt no kaihatsu bessatsu (plant gijutsu kenkyu chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

Research was made on new geothermal power plant technologies such as downhole pump and dual boiler for development of the 10MW class binary cycle power plant using geothermal energy. In heat cycle calculation of dual boilers, the cycle performance of a subcritical multi-stage evaporation cycle with R-114 heat medium was obtained through cycle calculation, heat conduction calculation and profitability calculation. The calculation result suggested possible considerable reduction of heat loss due to heat exchange at a preheater and evaporator, and considerable reduction of discharge loss of hot water by such multi-stage evaporation cycle. In American, every geothermal binary cycle power plant adopts pressurized heat exchange between hot water and heat medium by using downhole pumps, and pressurized reinjection of hot water into the ground. Since downhole pump itself not yet satisfies its requirements enough, it is said that Department of Energy is now under consideration on the future R and D. (NEDO)

Fiscal 2000 achievement report. International demonstrative development of photovoltaic power generation system (Demonstrative study on grid-connected photovoltaic power generation system in Thailand); 2000 nendo seika hokokusho. Taiyoko hatsuden system kokusai kyodo jissho kaihatsu - Taiyoko hatsuden keitou renkei system jissho kenkyu (Tai)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-09-01

A demonstrative study was conducted in Thailand for grasping the effect on small electricity grids when several photovoltaic power generation systems, including AC modules, are connected to the grid. In fiscal 2000, surveys and studies were conducted about the data of the local power system, where to install the demonstrative system, and how to install the same, which were necessary for working out a basic design for Libong Island newly designated as the site for the demonstrative system. It was then concluded that the demonstrative system be a grid-connected 100 kW-level photovoltaic system comprising one main photovoltaic power station (85 kW), photovoltaic power systems for school buildings (3-6 kW, three schools), and AC modules (110 W, 10 locations). The manufacture of solar cell modules, grid-connected power conditioners, and measuring devices were completed. Civil engineering work and construction were under way on the site, including the construction of a management building, installation of concrete bases for solar cell arrays, construction of fences surrounding the site, and so forth. (NEDO)

Report of results of contract research. 'Research on magneto hydrodynamic (MHD) generation'; MHD hatsuden system no kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-03-01

Examination was conducted in detail on an MHD generation system by coal combustion, with the results reported. Concerning a gas table calculation program in coal combustion, it was prepared assuming 100% slag removal ratio in the combustor as the primary approximation. A combustor for MHD generation needs to efficiently burn fuel using high temperature pre-heated air as the oxidant, to fully dissociate/electrolytically dissociate seed, and to supply to the generation channel a high speed combustion gas plasma having a high electrical conductivity which is required for MHD generation. This year, an examination was conducted on technological problems in burning coal in an MHD combustor. As for the NOx elimination system in an MHD generation plant, an examination was made if the method studied so far in MHD generation using heavy oil as the fuel is applicable to coal. Also investigated and reviewed were various characteristics, change in physical properties, recovery method, etc., in a mixed state of seed and slag in the case of coal combustion MHD. (NEDO)

Experience with a biomass-fuelled power plant in Peru. Peru kokunai no biomass nenryoka no hatsuden plant no keiken

Energy Technology Data Exchange (ETDEWEB)

1992-11-01

This paper describes the result of operating a 25-kW biomass-fuelled power plant for 500 hours installed for people in a small village in jungle along the Amazon basin in Peru. The gasifier plant consists of two invert type gas combustors combined with series cyclone dryer filters. Filtration used activated carbons and cotton cloths. The fuel for the plant is wood chips containing water at 5.5% to 11% with calorific power of 20 mJ/kg, consumed at 2.0 kg of lumber per kWh (25 kWh). A gas analysis showed values of CO2 at 13%, CO at 14%, H2 at 18%, CH4 at 3%, and N2 at 52%. Because the fuel of wood chips may cause problems if the size is too large, a size of about 10[times]20[times]30 mm was selected finally. Pressure drop in the gas purifying system was measured using a manometer, which verified that a textile filtering material can be used. The gasoline engine rotation was fixed at 2700 rpm upon discussions. The gasoline engine had no need of modification except at a pipe to the carburetor. This system can be installed at any small village. 1 ref., 1 fig.

Accident and everyday use for small PV power supply system. 2; Saigaiji ken`yo kogata taiyoko hatsuden system. 2

Energy Technology Data Exchange (ETDEWEB)

Yokoyama, S.; Sano, N.; Itsumi, J. [Kumamoto Institute of Technology, Kumamoto (Japan)

1997-11-25

Study is under way for the development of a small power source system capable of supplying power to public facilities and home appliances at normal times and capable of turning immediately into a self-sustained power source in case of emergency. This study discusses a power source that is a combination of solar cell modules and a storage battery, which is subjected to analysis for its match with a light or a data-processing computer imposed as a load on the power source. In the experiment, the power source consists of solar cell modules and a rectangular wave inverter. The battery is a 12V/28Ah automotive battery, the solar cells are two 75W (17V/4.4A) modules, and the load is a fluorescent lamp, fan, electric bulb, or a computer. It is found that the system can operate near the maximum power point of the solar cell modules when the load is light and that the system still works on even when the load consumes more than what the solar cells module produce, this thanks to the battery serving as a backup. In the future, a test-dedicated small power source now under construction will be put to continuous operation for further study. 4 refs., 4 figs., 1 tab.

Report for fiscal 2000 investigations on effects imposed by introducing emission trading system; 2000 nendo haishutsuryo torihiki system donyu ni yoru eikyo ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With regard to effectiveness of the emission trading targeted to reduce the greenhouse effect gas emission, evaluation has been given from the three viewpoints: economies, environment, and household economy. In the research, simulations were implemented by using the GEC calculation model modified for introduction of domestic emission trading, and utilization of international emission trading. In evaluating the effects on industries and foreign trades, notice was given on the large energy consuming industries to discuss the effects of introducing the emission trading on the quantity of production and export. Regarding the effects on environment, calculations and discussions were given on greenhouse effect gas leakage rates to assess the greenhouse effect gas emission reducing effects from the domestic and international viewpoints. As a result of the discussions, it was found that the economies, environment and household economy are all benefited in regard with the domestic emission trading. Utilization of the international emission trading was also found to have sufficient positive benefit exist for the economies and household economy. (NEDO)

FY 1998 survey report on the project on field tests for high-efficient industrial furnace introduction. Manual; 1998 nendo koseino kogyoro donyu field test jigyo mannual

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The high-efficient industrial furnace is a technology with the use of ultra-high temperature air over 1,000 degrees C, which has been impossible. It has been developed since FY 1993. The technology can reduce the energy consumption amount by 30%, and there is a possibility of reducing not only CO2, but NOx by approximately 50% over the conventional method. The main technique of the technology is to preheat the air blown into the incinerator at much higher temperatures of 1,000 degrees C or more than those in the existing combustion and to blow fuel into that high-speed air flow using the short-time-change/heat-storage type heat exchanger. It was predicted that the target value set first can almost be reached, and there can be seen a possibility of its industrial application. Industrial furnaces are used in many industrial fields such as metal production industry, petrochemical industry and electric machinery industry. The energy conservation in these fields brings extremely marked effects, and therefore it is an urgent task to introduce the industrial furnace into the fields quickly. The concentrated R and D were finished in FY 1998, and the field test project for the introduction was actually started. (NEDO)

Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Research and development of photovoltaic power generation system evaluation technology (Research and development of system evaluation technology - Separate volume: Collection of data of photovoltaic power generation systems); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu (system hyoka gijutsu no kenkyu kaihatsu - Bessatsu: taiyoko hatsuden system data shu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the establishment of technologies for optimum designs and optimum operation for various types of photovoltaic power systems, data are compiled in this volume, collected from the field test facilities and residential photovoltaic power systems. Operating data and meteorological data from the field test facilities (interconnection system, independent system, and water pump system) are arranged as easy-to-use supplementary data to help studies in relation to the 'energy flow in the test field facility systems' which is in the fiscal 1999 achievement report. As for data collected from residential photovoltaic power systems, they are arranged as easy-to-use supplementary data to help studies in relation to the 'Data and evaluation of residential photovoltaic power systems' which again belongs in the fiscal 1999 achievement report. (NEDO)

Fiscal 2000 report on result of international joint demonstrative development of photovoltaic power generation system. Demonstrative research on photovoltaic power generation system interconnection system (Myanmar); 2000 nendo taiyoko hatsuden system kokusai kyodo jissho kaihatsu seika hokokusho. Taiyoko hatsuden keito renkei system jissho kenkyu (Myanmar)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Joint research was conducted with Myanmar on a photovoltaic power generation system interconnection system, for which fiscal 2000 results were described in this paper. Power generating facilities were set up consisting of 80kW photovoltaic, 40kW wind and 60kW diesel systems. With the photovoltaic and wind power generation connected to a small-scale power system as a ballast load, the system interconnection is formed through load adjusting equipment such as storage batteries. The hybrid system feeding is from 6 o'clock early in the morning until 23 late at night. The diesel power generation is free from restrictions. The operating method was set on system control (demand side management) by adjustment from the load side, with ballast load control employed that adjustably operates an ice machine load. The basic design was drafted in terms of a storage battery capacity of 1,000Ah and an ice machine load of 32kW. The daytime load was assumed to be 25% of the night load. On the equipment specifications set in this basic design, arrangement design was conducted for the equipment in the premises, making a land development plan and a basic construction plan including a temporary work site, construction steps, transportation and delivery of the equipment. Quantity of solar radiation and wind data were continuously observed. (NEDO)

Development of hot water utilizing power plant in fiscal 1998. Development of a binary cycle power generation plant (development of a 10-MW class plant); 1998 nendo nessui riyo hatsuden plant nado kaihatsu. Binary cycle hatsuden plant no kaihatsu (10MW kyu plant no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This paper summarizes the achievements in fiscal 1998 on developing a 10-MW geothermal power plant in the Hohi-Sugawara area being a representative area of middle-to-high temperature hot water resources. In designing the plant, domestic and overseas surveys were carried out on media suitable for binary cycle power plants, thermal cycle characteristics, construction cost, environmental effects, safety, operation, maintenance and control. Latest technologies were also surveyed and analyzed. The plant construction performed development construction around the testing devices, new construction of a plant control room building, constructions for installing electrical machines including the hot water system testing devices, river water intake facility construction, and cooling water intake facility installing construction. The environmental effect investigation included investigations on rain falls, river flow rates, hot springs, spring water, monitoring during the construction, and the state of transplantation of precious plants, and observation on groundwater variation. In verifying the geothermal water pumping system, factory tests were carried out on DHP3 demonstration machine which couples the pump section of a down-hole pump with the motor section, whose performance and functions were verified. (NEDO)

FY 1994 report on the results of the development of a large wind power system. Development of control technology of the array type wind power system; 1994 nendo ogata furyoku hatsuden system kaihatsu seika hokokusho. Shugogata furyoku hatsuden system no seigyo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-01

This technology development aims at developing the design technology of the array type wind power system and the control technology to efficiently operate the system. As a result, the wind turbine produced by Micon was selected. The rated power is 100kW, and the number of the wind turbine is three. The three-phase short-circuit capacity at the generating end of the wind power generation facilities is 26,25 MVA, which can fully be broken. A simulation of voltage variation/frequency variation was made to grasp various phenomena of the output of the wind power system influencing the power source system and power distribution system. As a result, it was confirmed that it is possible to operate the system safely without lowering the quality of power. As to the overall monitor/control system which controls wind turbines, five wind turbines as many as possible are grid-interconnected and the number of wind turbine is to be controlled by a ratio of the total demand power to the gross generating output of wind power in the Miyako system, for the purpose of increasing the rate of equipment utilization of the wind power system also at the time of the lowest load of the Miyako system. In the operation of two-system interconnection, the gross power generating amount was 1,321,250 kWh, which increased 9.7% over the results in FY 1993. (NEDO)

Fiscal 2000 report on data of international joint demonstrative development of photovoltaic power generation system. Demonstrative research on photovoltaic power generation system interconnection system (Myanmar); 2000 nendo taiyoko hatsuden system kokusai kyodo jissho kaihatsu hokokusho. Taiyoko hatsuden keito renkei system jissho kenkyu (Myanmar) - shiryohen

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This paper describes the fiscal 2000 report on research data of joint demonstrative development with Myanmar concerning photovoltaic power generation system interconnection system. The purpose is an operation research in the case where a small-scale electric power generation system in an remote island or the like in Japan is linked with a severely output-fluctuating power generation system using energy of nature such as photovoltaic and wind power generation. In particular, among the system control (demand side management) methods by adjustment from a loading side, ballast load control was employed that adjustably operates load of an ice machine for example. As the contents of the data, the quantity of solar radiation and wind velocity at the Chaungthar site were shown as meteorological observation data. In addition, a graph was made on the meteorological observation data at the Chaungthar and Letkhokekone sites. The paper also explains the final explanatory data for selecting the sites in implementing the demonstrative research. As to the operation method of the hybrid power generation system, assumption was made for the daytime load in four cases from 50% (30kW) to 0% (0kW) of the nighttime. Storage batteries and diesel generators were installed and used in combination. Simulation results were also presented. (NEDO)

Study on gas turbines. Leading role of high efficiency power generation; Gas turbine kenkyu. Kokoritsu hatsuden no shuyaku wo nerau

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-01-31

This review summarizes research works of Central Research Institute of Electric Power Industry on gas turbines playing a leading role of high efficiency power generation. This article describes historical changes of gas turbine technology, changes and current status from the viewpoint of electric power industry, and development trend in various makers. Increase in the flow-in gas temperature, low NOx combustion technology, use of various fuels, and durability evaluation and improvement technology for high temperature parts are described as technological problems and development trends. The increase in temperature is indispensable for the improvement of efficiency. Materials having heat resistance, anticorrosion and strength are required. Accordingly, Ni-based single crystal super alloy has been developed. Developments of ceramic gas turbine and catalytic combustor are also described. The coal gasification combined power generation is expected as a new power generation technology having availability of various coals, high efficiency, and excellent environmental protection. Development of 1500 {degree}C class combustor for turbines has been promoted. Evaluation and improvement of durability of high temperature parts are also described. For the new utilization technology of gas turbines, repowering and compressed air storage gas turbine power generation technology are introduced. 92 figs., 14 tabs.

Experiments of cooling photovoltaic panel by desorption process; Dacchaku hanno wo riyoshita taiyoko hatsuden panel no ondo josho yokusei jikken

Energy Technology Data Exchange (ETDEWEB)

Akisawa, A; Inoue, S; Kashiwagi, T [Tokyo University of Agriculture and Technology, Tokyo (Japan)

1997-11-25

It is important to cool a photovoltaic (PV) panel, because increased panel temperature is accompanied by decreased power generation efficiency. The authors have proposed a PV power generation system combined with an adsorption chiller driven by low-temperature heat, and simulated temperature changes during the desorption cycle, where the chiller utilizes endothermic reactions of an adsorbent during the desorption cycle. Described herein are results of the tests carried out to validate possibility of controlling panel temperature increase. The system consists of the PV panel with which a bed packed with an adsorbent is monolithically combined, condenser and evaporator. It generates power during the daytime by sunbeams, and provides low-temperature heat during the nighttime by the evaporator. In particular, ice can be produced when methanol and activated coal are used as the adsorbate and adsorbent. It has an advantage of effective utilization of energy as the heat source, which has been merely dissipated by the conventional system in the air. Such a system is expected to be useful for promoting effective utilization of solar energy and for peak power shaving in summer. The initial targets are achieved by the tests. 4 refs., 10 figs.

Report on results of contract research. 'Research on MHD generation system'; MHD hatsuden system no kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

'Research on MHD generation system' was implemented by its expert committee in the electric joint study group, with the results of fiscal 1981 reported. This year, technological reexamination was conducted for a 2,000 MWt commercial MHD generation plant, with evaluation carried out on the cost performance including the construction and operation cost. In addition, for the purpose of intermediate R and D towards the practicability, examination was also conducted on a system structure, concrete specifications of component element, cost of R and D including operation expenses for example, concerning an 100 MWt class experimental plant and a 500 MWt class plant. In the investigation of the overseas trend, information was summarized in detail on the experimental devices, combustors, generation channels, electrode materials, electrode phenomena, theoretical analyses, seeds, slag, component equipment, instrumental technologies, conceptual designs of generation plant, commercial plant, etc., in Soviet Union, China, Holland, India and EPRI, on the basis of the materials from the 19th MHD symposium held in UTSI and from the coal MHD specialist conference held in Sydney. (NEDO)

Report on results of contract research. 'Research on MHD generation system'; MHD hatsuden system no kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

'Research on MHD generation system' was implemented by its expert committee in the electric joint study group, with the results of fiscal 1980 reported. This year, a detailed conceptual design was carried out on a coal fired MHD generation system, with points for the technological development concretely examined. In addition, investigation was conducted on the progress of MHD generation technology, development situation of other generation systems, state of energy resources, etc., in various foreign countries. In the conceptual design of the coal fired MHD generation plant, the system structure of a 2,000 MWt class commercial MHD generation plant was explained, as were the conceptual design of the structural elements and proposals for a 500 MWt class demonstration plant and an 100 MWt class experimental plant, for example. In the overseas trend of R and D on MHD generation, investigations were made concerning the U.S., Soviet Union, and China, with details compiled for such items as generation plants, combustors, generation channels, heat resisting materials, superconducting magnets, heat exchangers, seed slags, inverters, boilers and environments, and commercial plants. (NEDO)

Demonstrative study for the wind and solar hybrid power system. 2; Furyoku taiyoko hybrid hatsuden system ni kansuru jissho kenkyu

Energy Technology Data Exchange (ETDEWEB)

Kimura, Y; Sakuma, H; Ushiyama, I [Ashikaga Institute of Technology, Tochigi (Japan)

1996-10-27

In order to verify the complementary relationship between wind and solar energy, the long-term field test of the hybrid power system was conducted at the natural energy square of Ashikaga Institute of Technology. The solar cell blade windmill composed of a Savonius windmill and flexible solar cells applied to swept buckets was also prepared. As a result, the wind power generation was promising mainly in the winter period including the late fall and early spring, while solar one was stable all the year through although it was slightly poor in winter. Stable power generation was thus achieved by combining wind energy with solar energy. As the whole data of other wind and solar power generation systems at the square were analyzed for every month, the same conclusion as the solar cell blade windmill was obtained as follows: the wind power generation in Ashikaga area is promising in Nov.-March from the field test result for 16 months, solar power generation is stable all the year through, the hybrid power system is effective in Nov.-April, and the solar cell blade windmill is equivalent to the hybrid power system. 3 refs., 5 figs.

Research report. Environmentally friendly energy community research business for Fujieda district (Refuse energy utilization); Fujieda chiku kankyo chowagata energy community chosa jigyo (haikibutsu energy riyo shisetsu) chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

An environmentally friendly refuse energy utilizing business, for which RDF (refuse derived fuel) produced out of wastes discharged by industries belonging to a Fujieda city environmental protection council will provide the heat source, is proposed by the said council. The proposal is subjected to a study, a basic plan is drafted, and a decision is made on its profitability. In the study, surveys are conducted on the actualities of wastes and of demand for heat, and specifications are worked out relating to transportation and storage of RDF, production of steam by an RDF-fired boiler, routing of pipes for transmitting the steam to the industries in the district, facility costs, operating costs, etc. It is found that the amount of RDF produced out of the wastes discharged by the council member industries is so small that it can meet the demand of only one industry and that, even if more wastes are collected from a wider area, the increased amount will but meet the demand of two industries and a hot water pool. It is found that the system will be economically feasible, however, if the shortage of RDF-generated energy is covered by an oil-fired boiler and thereby impartiality is established in steam distribution and steam production unit price is reduced. In view of the intensification of control over dioxin, etc., the business will be gaining profit in 2002 and after. (NEDO)

Fiscal 1998 research report. Feasibility study on next-generation environment-friendly urban transport systems; 1998 nendo chosa hokokusho. Jisedai kankyo kyosei toshi kotsu system donyu kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This research arranges recent public transport system technologies such as LRT, and clarifies their technical issues to be overcome and developmental courses, and the improvement effect of their energy efficiency and CO{sub 2} reduction effect by such measures to contribute to development of next-generation public transport systems. The outlines and features of LRT, monorail/trolley bus and AGT as existing public transport systems are arranged. In the EU, development of tramways using rubber tires is in promotion. The concept of a next-generation environment- friendly urban transport system is prepared based on features of every public transport system. Since a trolley system causes traffic congestion and environment deterioration, introduction of an independent transport system with fuel cell is necessary in the future. The technical issues and solutions for construction of the next-generation transport systems are analyzed. Fuel cell and ITS are important candidates. Substitution of the next-generation transport system for existing buses showed a CO{sub 2} reduction effect of 3.91 Mton/y in Japan. (NEDO)

FY 1990 achievement report on the survey of possibility of introducing solar energy into buildings; 1990 nendo taiyo energy no kenchikubutsu eno donyu kanosei chosa seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-03-01

This paper describes the achievements in fiscal 1990 on survey on possibility of introducing solar energy into buildings. Capacity of photovoltaic power generation facilities installed on an area of 1600 km{sup 2}, such as roofs of residential houses, schools and building may be calculated on a trial bases as 100 million kW at maximum. The capacity can replace 16% of the total demand and corresponds to 26.30 million kiloliters (9%) as converted to crude oil. If photovoltaic power generation is utilized on buildings of users, diversified technological criteria are required from the viewpoint of legislation covering wide range of architectural, electrical and disaster aspects. However, no direct and clear standards are available now, except for the electric power business law. What are urgently required are solar cell standardization, incentive subsidies, aging safety, institutions for electric power sale and purchase, and establishment of technological criteria. An utilization example survey revealed problems in array installation and size. Increased demand, mass production and cost reduction will create a favorable cycle. Introduction, proliferation, and acceleration under policies at public facilities which are expected of enlightenment and development into other areas will be the effective means for the purpose. (NEDO)

Fiscal 1997 development of fuel cell power generation technology. Part 3. Supplementary explanation to R and D of molten carbonate fuel cell and power generation system; 1997 nendo nenryo denchi hatsuden gijutsu kaihatsu hosoku setsumeisho. 3. Yoyu tansan'engata nenryo denchi (hatsuden system no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1988-05-01

A supplementary explanation was compiled for the results of a commissioned project reported in fiscal 1997 (development of fuel cell power generation technology, and R and D (3) of molten carbonate fuel cell and power generation system). The supplementary explanation was given on the development of parallel flow stack, design/manufacturing of 250 kW stacks, design and manufacturing of 250 kW stacks in connection with installation/adjustment. (NEDO)

FY 2000 report on the development of hydrothermal use power plant, etc. Development of the binary cycle power plant (Development of a 10MW class plant); 2000 nendo Nessui riyo hatsuden plant tou kaihatsu. Bainari cycle hatsuden plant no kaihatsu - 10MW kyu plant no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-01-01

For the purpose of developing a 10MW class demonstrative plant for geothermal binary power generation, the R and D were carried out, and the results obtained from FY 1995 to FY 1999 were summed up. In the interim evaluation made in July 1994, study was to be phasedly proceeded with for the main three systems (hydrothermal system, medium system and power generation system) which compose the 10MW class binary cycle power plant. The test on the hydrothermal system was started in FY 1995. In the R and D, the following were conducted for evaluation: design/manufacture/installation of the test device for the hydrothermal system, manufacture of demonstrative downhole pump (DHP) No.3 and test at plant, test on the hydrothermal system. As to the turbine working medium suitable for binary power plant, the specified freon/substitute freon have been used, but it seems that hydrocarbons such as butane and pentane can be effective in future. In the study of the economical efficiency, it was pointed out that for the commercialization, it is important to improve durability of DHP and further reduce the cost of DHP equipment and cost of repairs. (NEDO)

Sampling and preparation method for mutagenicity test of exhaust gas from municipal waste incinerator; Haikibutsu shokyakuro hai gas no hen`i gensei shiken no tameno shiryo saishu/chosei hoho

Energy Technology Data Exchange (ETDEWEB)

Yoshino, H. [Kanagawa Environmental Research Center, Kanagawa (Japan); Urano, K. [Yokohama National Univ. (Japan)

1994-09-10

It is well known that many kinds of hazardous organic compounds in incinerator exhaust gases. In this study, a simple sampling method to test mutagenicity on exhaust gases in flue and its extracting and its solvent converting methods by organic solvents were examined. In sampling 100 to 300 l at about 2 l/min in aspirating speed of the extract gases, the most of mutagenic substance were collected almost completely by condensed water and qualtz wool column. And, the collected materials into the condensed water could almost perfectly recovered by extracting the condensed water with about its one fourth volume of ethylacetate on vibrating once in 5 min., extracting the quartz wool column on flowing 20 ml of ethylacetate at the speed of about 3 ml/min., and others. After mixing such effluents and dewatering with about 5 g of sodium sulfate, they are evaporated out ethylacetate and resolved with 5 ml of dimethylsulfoxide (DMSO) to execute Ames mutagenicity test. As a result, more than about 3000 net rev./Nm{sup 3} of the mutagenicity was estmated on TA 98 strain. 9 refs., 5 figs., 8 tabs.

Report of results of contract research. 'Research on magneto hydrodynamic (MHD) generation'; MHD hatsuden system no kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-03-01

Examination was conducted in detail on an MHD generation system by coal combustion, with the results reported. Concerning a gas table calculation program in coal combustion, it was prepared assuming 100% slag removal ratio in the combustor as the primary approximation. A combustor for MHD generation needs to efficiently burn fuel using high temperature pre-heated air as the oxidant, to fully dissociate/electrolytically dissociate seed, and to supply to the generation channel a high speed combustion gas plasma having a high electrical conductivity which is required for MHD generation. This year, an examination was conducted on technological problems in burning coal in an MHD combustor. As for the NOx elimination system in an MHD generation plant, an examination was made if the method studied so far in MHD generation using heavy oil as the fuel is applicable to coal. Also investigated and reviewed were various characteristics, change in physical properties, recovery method, etc., in a mixed state of seed and slag in the case of coal combustion MHD. (NEDO)

Preparation of the FY 1998 photovoltaic power system related technology information; 1998 nendo taiyoko hatsuden system kanren gijutsu joho no seibi

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The paper outlined the FY 1998 data preparation project on the photovoltaic power generation. In the field of solar cells and photovoltaic power system, a part of the 13th EUPVSEC data and the 25th IEEEPVSEC data are made database. As to the NEDO related papers, the papers made public in FY 1998 are made database. The number of the object papers totaled 982 including 943 in international conference relation and 39 in NEDO relation. The number of the papers included in 'photovoltaic power generation database (literature)' totaled 4010. Steps of database preparation are collection of the research papers/various reports made public in Japan and overseas, abstract making, preparation of the result data/experimental data, keyword supply, classification/adjustment, and description items. The FY 1998 is the fifth year from the start of this database, and the collected/adjusted technical information on solar cells is classified for analysis according to international conference, research institute, used material, research field, etc. (NEDO)

Prediction of velocity of the wind generation in Kobe City College of Technology; Kobe Kosen ni okeru furyoku hatsuden no yosoku

Energy Technology Data Exchange (ETDEWEB)

Akamatsu, K; Kanemura, M; Amako, K

1997-11-25

Wind conditions, such as average wind velocity for 10 minutes, maximum instantaneous wind velocity and wind directions, are measured by the anemometer and anemoscope installed 3m above the roof of the Kobe City College of Technology`s Information Processing Center building, to collect the data necessary to validate possibility of wind power generation, if the wind system is installed in the college site. Monthly availability of power is estimated from the output power characteristics curve for a generator having a rated capacity of 200W and wind velocity data collected for 9 months. It will generate power of only 144kWh, even when operated to give the rated output, or approximately 8.5kWh at the highest in a month, because of availability of wind power limited to around 30% of the total as estimated from the relative frequency distribution. It is therefore desirable to install a number of units having a rated capacity of 200W or else a smaller number of larger units. Assuming that days that give the highest output for 24 hours last 1 month, a power of 54.3kWh will be generated. It is estimated, based on these results, that a hybrid unit, in which a wind power generator installed at a high place is combined with a solar unit, can provide power required for nighttime lighting, if a wind power unit having a rated capacity of 2kW is field-controlled under an optimum condition. 13 figs., 3 tabs.

Photovoltaic AC fusion converter (PVAC). Design consideration and experimental evaluation; Taiyoko hatsuden denryoku/shoyo denryoku kongo sochi no hoshiki to seino

Energy Technology Data Exchange (ETDEWEB)

Tsuchiya, Y. [Hachinohe National College of Technology, Aomori (Japan); Sakakibara, T. [Toyohashi University, of Technology, Aichi (Japan)

1997-11-25

The photovoltaic AC fusion converter (PVAC), of which cost reduction of the total system is possible, was developed. PVAC controls the supply of commercial power by preferentially supplying photovoltaic power to loads for realization of energy conservation. Further, setting the maximum output of solar cell less than the rated load, the system was made the one with no need of storage batteries. This system was realized in a hybrid of the conventional rectification technology and the stand-alone maximum power point tracking photovoltaic system technology. The solar cell input efficiency had been measured as 84% at maximum. Main losses are consumption power of power source, switching loss of inverter, and continuity loss of diode. Ninety-seven percent of the commercial power input efficiency was obtained. Main losses are consumption power of power source, continuity loss of diode bridge, and resistance loss of smoothing reactor. The effect of energy conservation by the use of PVAC was also admitted. 6 refs., 7 figs.

Preparation of the FY 1998 photovoltaic power system related technology information; 1998 nendo taiyoko hatsuden system kanren gijutsu joho no seibi

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The paper outlined the FY 1998 data preparation project on the photovoltaic power generation. In the field of solar cells and photovoltaic power system, a part of the 13th EUPVSEC data and the 25th IEEEPVSEC data are made database. As to the NEDO related papers, the papers made public in FY 1998 are made database. The number of the object papers totaled 982 including 943 in international conference relation and 39 in NEDO relation. The number of the papers included in 'photovoltaic power generation database (literature)' totaled 4010. Steps of database preparation are collection of the research papers/various reports made public in Japan and overseas, abstract making, preparation of the result data/experimental data, keyword supply, classification/adjustment, and description items. The FY 1998 is the fifth year from the start of this database, and the collected/adjusted technical information on solar cells is classified for analysis according to international conference, research institute, used material, research field, etc. (NEDO)

Output characteristics of floating type wave power generator system using a ball screw; Fuyugata nejishiki haryoku hatsuden sochi no shutsuryoku tokusei

Energy Technology Data Exchange (ETDEWEB)

Abe, T; Omata, K [Meiji University, Tokyo (Japan)

1996-10-27

A floating type wave power generator system using a ball screw is proposed. Output characteristics are simulated on the supposition of its employment aboard a navigational aid buoy. The relative linear movement produced by waves between the main body and float is transmitted via a load column to a ball nut and is converted into a rotary movement of a threaded shaft engaging the ball nut. Attached to the bottom end of the threaded shaft is a one-way clutch which connects to the generator axle when the relative velocity between the float and main body is positive. The simulation was conducted for a wave activated power generation buoy, 2.6m in outer diameter, 4.5m in length, and 6000kg in total mass. The buoy generated a mechanical output of 340kW when exposed to a sinusoidal wave 2.5 seconds in period and 40cm in wave height. A tank test was performed using a reduced scale model consisting of a ball screw, bicycle dynamo, and float, with the main body being 318mm in diameter and 833mm in length, when an average output of 4.51W was obtained at 60% efficiency. The results of the experiment agreed in some degree with the results of calculation, verifying the righteousness of the theoretical formula. 3 refs., 7 figs., 4 tabs.

FY 1998 annual report on the introduction/dissemination working group. 19th R and D activity report; 1998 nendo donyu fukyu jigyo bunkakai. Dai 19 kai jigyo hokokukai

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-09-01

Summarized herein are the FY 1998 R and D activities by the introduction/dissemination working group, extracted from the 19th R and D activity report by NEDO. Mr. Yamaho, a NEDO's director, reports (General situations of the new energy introduction promotion department). The R and D project results include those of renewable energy sources, such as the results of the field test and supporting projects for solar light power generation, wind power generation and solar heat utilization; and those of recycling type energy, such as the results of the field test projects for power generation by wastes and fuel cells, and the results of the projects for district heat supply by co-generation systems. The other results presented include those of the projects for dissemination of clean energy vehicles, supporting new energy entrepreneurs, promotion of introducing district new energy, drawing visions for district new energy, field tests for introducing high-performance industrial furnaces, modeling for introducing facilities for rationalized use of pioneer energy, promotion of disseminating ice-aided, heat-storage type air conditioning systems, and promotion of introducing decentralized gas-aided air conditioning for existing small- to medium-sized buildings. (NEDO)

Analysis and evaluation for practical application of photovoltaic power generation system. Analysis and evaluation of peripheral technology for photovoltaic power system (analysis and evaluation on photovoltaic systems); Taiyoko hatsuden system jitsuyoka no tame no kaiseki hyoka. Shuhen gijutsu kaihatsu no tame no kaiseki hyoka (taiyoko hatsuden system shingata chikudenchi)

Energy Technology Data Exchange (ETDEWEB)

Kurokawa, K; Endo, E; Tsuda, I; Nakamura, K; Sugiyama, Y; Nakazawa, S; Takaku, K; Yanagisawa, T; Kojima, T; Shimizu, K; Koyanagi, T; Onda, N; Nozaki, K; Negishi, A; Kaneko, Y [Electrotechnical Laboratory, Tsukuba (Japan)

1994-12-01

Described herein are the results of the FY1994 research program for analysis and evaluation of new storage batteries for photovoltaic power systems. Quantitative analysis and evaluation are made for introduction of intermittent operational mode in the conventional power supply system in which electrolyte units are connected in parallel and for improved performance by bubbles flowing into the line that supplies the electrolyte to the stack, in order to establish the configurations of and operational procedures for the redox flow batteries. The study on development of redox battery compares the Pb-Sn alloy felt collector with carbon fiber, Pb-Sb alloy felt and the lattice for the conventional lead acid battery, in order to optimize the new lead felt battery. As a result, it is found that the Pb-Sn alloy felt collector is better than any other device tested, because of its higher freedom with respect to electrode shape and battery size. The study on reliability evaluation of amorphous solar cells tests photoelectric conversion efficiency of a-Si solar cells, in order to elucidate the phenomena where degradation and rejuvenation compete with each other under weak light irradiation conditions. 8 figs., 1 tab.

Achievement report for fiscal 1981 Sunshine Program on development of practical application technologies for photovoltaic power systems. Development of photovoltaic demonstration systems (Research and development of systems for factories); 1981 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden demonstration system kaihatsu (kojoyo system no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

In the effort at constituting an optimum system, a 2kwp mini-system is completed after designing and introducing an array output measuring unit, DC control unit, dummy loads, etc. The system is actually operated for collecting various data, and commercial noise, transmission line safety, surplus power utilization, solar cell utilization rate, efficiency of various kinds, etc., are subjected to analysis. The basic designs of measuring instruments for a 100kwp full-scale system are also examined. In relation with the manufacture, testing, and arrangement of solar cell arrays, a large solar simulator is designed and introduced for the measurement of module photoelectric characteristics. Using this simulator, continuous irradiation is performed by a 1kW/m{sup 2} light beam of a spectral distribution of AM (air mass) 1.5. A CZ (Czochralski) single crystal, EFG (edge defined film bed growth method) ribbon, and a small CdS/CdTe solar cell module are installed, through the use of which operating characteristics are determined for comparative study. A DC control unit is designed and built, composed of a rectifying device for the dissolution of noise that greatly affects measurement for the mini-system, DC-AC-DC converter, and a remote control console. (NEDO)

Development in fiscal 1999 of technology to put photovoltaic power generation system into practical use. Demonstrative study on photovoltaic power generation system (Research on high-density linking technology); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden system no jissho kenkyu (komitsudo renkei gijutsu no kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Taking a photovoltaic power generation system linked to distribution lines at high density as the object of discussion, investigative studies were performed on electric power quality, clarification of various problems including effects on operation and protection of distribution lines, the corrective measures thereof, and enhancement of power quality by utilizing inverters. This paper summarizes the achievements in fiscal 1999. In clarifying the problems associated with high-density linkage, discussions were given on possible amount of PV introduction into the distribution lines as seen from the electric performance aspect including power quality and safety. Placing the importance on identifying the current status of single operation preventing technologies, demonstrative discussions were given on the single operation preventing performance of commercially available inverters in testing 84 inverters operated in parallel by using the Rokko testing installation. In discussing the corrective measure technologies, development has been performed on a decentralized voltage stabilizing device based on injection of reactive power into high-voltage distribution lines as a measure to suppress voltage rise in the distribution lines. The reasonability of the fundamental characteristics thereof was verified by using the Akagi testing facilities. In addition, improved design was progressed on the two-step active prevention system. Commencement has taken place on verification of the reasonability of the fundamental characteristics and tests on parallel operation of multiple number of units. (NEDO)

FY 1998 Report on development of technologies for commercialization of photovoltaic power systems. International co-operative project (IEA implementing agreement for a co-operative programme on photovoltaic power systems); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu kokusai kyoryoku jigyo. IEA taiyoko hatsuden system kenkyu kyoryoku program jisshi kyotei

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Described herein are outline of the International Energy Agency/Co-operative programme on Photovoltaic Power Systems (IEA/PVPS). Japan signed the IEA Implementing Agreement for a co-operative programme on Photovoltaic Power Systems in April 1993, and has been participating in the programme for research and development, demonstration, analysis, information exchange and introduction promotion, among others. This programme is managed by Executive Committee composed of the representatives, one nominated by each participating country, and each task is managed by each Operating Agency. There are 9 tasks (Tasks 1 to 9), and Executive Committee deliberates and approves the plans, and manages the progresses, budgetary plans and budgets for each task. IEA implementing agreement for a co-operative programme on PVPS, originally set effective for 5 years, has been extended for another 5 years to 2002, and the second phase activities have been started. The 9th to 11th Executive Committee meetings were held during the 1997-1998 period in Denmark, ROK, Spain, Austria and Australia, respectively. (NEDO)

FY 1989 report on the results of the development of the entrained bed coal gasification power plant. Support study for the development of the entrained bed coal gasification power plant; 1989 nendo seika hokokusho. Funryusho sekitan gaska hatsuden plant kaihatsu (Funryusho sekitan gaska hatsuden plant kaihatsu no shien kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1990-05-01

For the purpose of supplying the data necessary for construction/operation/maintenance of system, gas turbine, etc. of the desulfurization/dust removal process to be adopted to a pilot plant of 200t/d entrained bed coal gasification power generation, support study was made using the Yubari 40t/d test equipment, and the FY 1989 results were summarized. As to the operation of the 40t/d gasification system, operation was stably continued, and also the system was able to feed gas to the wake device. In the high temperature dry desulfurization test, test was made on the following: structure of the sampling system of the continuous analyzer installed in the coal gas system and circulation gas system, load response corresponding control system, sequence control of the system for supplying reducing agent to SO{sub 2} reduction tower and the system for ash discharge, back washing of D-42 lift gas filter, etc. In the high temperature dry dust removal test, improvement in filtration material/dust separation performance, sequence control of the filtration material supply/discharge system, continuous dust densitometer, operational automation, etc. Through the tests, obtained were the results that are useful for the 200t/d plant. (NEDO)

Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. International cooperation projects (Collection of information on IEA photovoltaic power generation program); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Kokusai kyoryoku jigyo (IEA taiyoko hatsuden program ni kansuru joho shushu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Items of information were collected on development of technologies to put photovoltaic power generation systems into practical use, the international cooperation projects, and the IEA photovoltaic power generation program. This paper summarizes the achievements in fiscal 1999. In the activities of IEA/REWP/PVPS in the current fiscal year, the 13th and 14th Executive Committee meetings, and the 3rd Executive Conference were held. The Task 1 has performed such activities as ISR, NSR, Newsletters, and opening the Internet homepage. The Task 2 activities included structuring about 260 databases for the operation characteristics of photovoltaic power generation systems, and completing the internal material handbooks on measurement and monitoring. A new work plan was prepared for the Task 3 regarding an independent photovoltaic power generation plant for use in an island. For the building integrated photovoltaic power generation system in the Task 7, survey activities were executed by utilizing expertise conferences on building designs, system technologies, and non-technical impediments. In the feasibility survey and research on large-scale photovoltaic power generation utilizing unused land such as desert for the Task 8, the programs were established. (NEDO)

FY 1999 Report on the technical results. Part 1. Development of fuel cell power generation technologies (Research and development of molten carbonate fuel cell power generation system); 1999 nendo nenryo denchi hatsuden gijutsu kaihatsu seika hokokusho. 1. Yoyu tansan'engata nenryo denchi (hatsuden system no kenknyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

This research and development project is aimed at development of the stacking, cooling and operating technologies for the molten carbonate fuel cell power generation systems, to improve service life and performance of these systems and reduce their cost, based on the results obtained so far by the FY 1993. The R and D efforts are directed to (1) technologies for improving stack performance, (2) development of the plant system by operating a 1,000kW class power generation system, and (3) support technologies, e.g., those for stack materials. The item (1) studies 3 stack types, cross-flow, parallel-flow and internal reforming types, including the electrodes, electrolyte-supporting bases and improvement of performance and service life by separator reforming for the cross-flow and parallel-flow types, and installation and operation of a 200kW class stack system for the internal reforming type, where cells are assembled into the system and tested for their operability, after the auxiliary units are PAC-tested. The item (2) installs a 1,000kW class plant, which is operated, after clearing the requirements set by the related laws, e.g., Electric Utility Industry Law, for starting the operation, to achieve the intended targets. The item (3) includes development of the technologies for stack materials, technologies for handling gases produced by coal gasification, and studies on the total systems. (NEDO)

Wastes disposal on board a ship. Crushing and volume reducing apparatus for combustible and non-combustible refuses; Senjo no haikibutsu shori. Kanen funen gomi no hasai gen`yo shori sochi

Energy Technology Data Exchange (ETDEWEB)

Kishida, Y. [Hitachi Zosen Corp., Osaka (Japan)

1996-07-25

This paper introduces a refuse crushing apparatus to reduce for storage the volume of refuses produced on board a ship by crushing. Refuses to be crushed are solid wastes including solid combustible refuses such as paper, wood pieces, and cloths, non-combustible refuses such as empty cans, metals and glass, and refuses unsuitable for combustion, such as plastics and stylofoam. Crushing methods include impact system, compression system and shearing system. The shearing system shears and crushes refuses by using blades rotating at a low speed. The system has a wide range of crush ability and excellent versatility, generates low levels of dust, noise and vibration, and is suitable as a marine use refuse disposing apparatus. However, empty cans and PET bottles are more difficult of getting into cutting blades requiring a large amount of time for crushing. Therefore, it is more suitable to reduce volume of refuses by using a compressor or the like apparatuses, and then crush them by using a double-axial shearing crusher. Stylofoam causes its crushed pieces to be electrically charged and deposited onto the apparatus, hence it is more suitable to reduce the volume of refuses and make them brittle by heating, and then crush them by using the double-axial crusher. 2 figs.

Survey of the measures to be concretely taken for CEV introduction/spread in the region; Chiiki ni okeru CEV donyu fukyu no tame no gutaiteki hosaku ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

For the Hanshin/Harima region where CEV introduction/spread are expected and there is a great pervasive effect, survey/study were conducted to plan the construction of facilities for natural gas vehicle fuel supply in future. In the survey, the paper summed up the state of CEV spread in the Hyogo prefecture, the state of construction of fuel supply facilities, etc. Further, by the questionnaire survey, the needs for construction of fuel supply facilities were grasped, and the intention of introducing natural gas vehicle was sounded out. In the study of a wide-area construction plan for natural gas fuel supply facilities, the Hanshin/Harima region was divided into zones based on geographical conditions, traffic system, etc., and the number of the needed fuel supply facilities was calculated which corresponds to the targeted number of natural gas vehicle introduction set up by the nation. Moreover, by the questionnaire survey, the needs for fuel supply facilities were grasped, and a method for setting up the order of priority in the construction was determined/proposed. Through the study of these, a manual was made out which is usable for the CEV introduction and the construction plan for natural gas fuel supply facilities in other regions. (NEDO)

Fiscal 1994 report on the survey of making models for introducing petroleum substituting energy systems; 1994 nendo chosa hokokusho (sekiyu daitai energy system donyu model sakusei ni kansuru chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

In the promotion of measures taken for energy conservation, it is necessary to give local governments, entrepreneurs, etc. appropriate and concrete guidance for introducing energy systems which meet with features of the areas and buildings and courses for how to construct infrastructures of towns or cities in case of development and redevelopment. Recently, also in local governments, etc., there are seen attitudes toward positive study of introduction of energy conservation systems and petroleum substituting energy systems in case of redevelopment, and the situation is that the spread and expansion are expected by giving appropriate guidance for the introduction. Accordingly, the study makes analyses of the trend and characteristics of developmental projects and makes/arranges models of promising petroleum substituting energy systems, aiming at contributing to promotion of guidance for the introduction to local governments, entrepreneurs, etc. Approximately 20 models of petroleum substituting energy systems were made which are thought to be promising. For each, the following were arranged: outline of system, introduction target, introduction effects, the point of promotion of the introduction, related subsidy systems, actual results, etc. 22 figs., 34 tabs.

Survey on the feasibility of high-efficiency gas turbine power generation system; Kokoritsu gas turbine hatsuden system ni kansuru jitsuyo kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

For higher-efficiency power generation cycle plants with less restrained conditions for a location, the conceptual design of an inter-cooled regenerative two-fluid cycle plant (ISTIG) was attempted using a modified aircraft gas turbine. A high-performance turbo fan engine is used for middle-class power generation. The first stage combustion gas drives the first stage turbine, and its exhaust gas is used for the second stage combustion. Because of two-axial type of high and low pressure, improvement of thermal efficiency is expected by easy-to-install inter-cooler. ISTIG superior in operability is suitable for medium load or distributed power generation facilities, and aims at higher efficiency of a 60% level. ISTIG includes a large amount of water vapor in combustion air by adopting a diffusion type combustor eliminating back fire, and can reduce exergy loss by preheating fuel gas. Since load of the high-pressure turbine shifts toward low-pressure one by the inter-cooler, some considerations are necessary for low-pressure side cooling together with reheating cycle. Because of unnecessary steam turbine, the construction cost per kW can be reduced by 20%. 41 refs., 64 figs., 27 tabs.

Summary of results of research on magneto hydrodynamic (MHD) generation in fiscal 1977; 1977 nendo denji ryutai (MHD) hatsuden kenkyu seika gaiyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1978-08-01

This is the summary of results of the research on MHD generation in fiscal 1977. In the experimental studies on MHD generators using a copper/iron magnet, the combustor of the Mark 7 generator was manufactured and installed, as were the supply systems of fuel, oxygen, air, seed, sulfur dioxide, cooling water, etc., respectively of the Mark 7 generator based on the design implemented in the previous year. In the studies on element technologies, various tests were performed, namely, immersion tests by K{sub 2}SO{sub 4} solution for electrode materials; tests of corrosion resistance, thermal shock resistance, and compatibility with electrode materials, for insulation wall materials; and material selection tests, based on a dynamic state, for consumption quantity and distribution, surface temperature and heat flow, measurement of arc spot generating critical current and electrode lowering voltage, etc.. In the research on the MHD generation system, examinations were carried out on the position of MHD generation as a total system, as well as on a system of a practical plant, MHD generation for peak load, superconducting magnet, etc. In addition, examinations were also conducted on the Mark 7 calculation, Mark 8 plan, surveys on overseas trend, etc. (NEDO)

Interim report on research and development of magnetohydrodynamic (MHD) power generation. General remarks; Denji ryutai (MHD) hatsuden kenkyu kaihatsu chukan hokokusho. Soron

Energy Technology Data Exchange (ETDEWEB)

NONE

1973-08-01

This report covers the MHD power generation research and development project which has been under way for 7 years since fiscal 1966, and contains guidelines to follow in the next 3 years during which studies will continue toward the consummation of the project. Subjected to research and development under this project are the development of superconductive magnets and helium refrigeration/liquefaction equipment, clarification of the power generation characteristics of the 1,000kW-class MHD (magnetohydrodynamic) power generator and of a test machine designed for a long-term operation, etc. Since they contain many basic studies, the efforts are being exerted primarily by the Electrotechnical Laboratory. In the research and development of MHD power generation characteristics, a power generation experiment is conducted through oxygen combustion in a hot wall channel, with the combustor and insulation against the Hall voltage improved. In this test, a maximum output of 1,182kW is achieved under the conditions of a flow rate of 2.9kg/s, a thermal input of 24.6MW, and a flux density of 3.2T. Since there are some problems to solve in connection with the stability of MHD power generation characteristics, durability of the MHD power generation channel, characteristics of heat exchanger system, measures for NOx reduction, etc., some more deliberation is necessary before taking the next research and development step. (NEDO)

Solar power generation test project at Sakata Nursery School (Oizumi town, Gunma prefecture); Sakata hoikuen taiyoko hatsuden field test jigyo (Gunmaken Oizumimachi)

Energy Technology Data Exchange (ETDEWEB)

Nakamoto, M.

1997-05-30

The solar power generation system was installed in fiscal 1996 on a south-facing roof of the Sakata Nursery School`s building. It has a capacity of 10kW, is used as the power source for illumination and air-conditioning, and for driving computers for children and office devices. It will demonstrate applicability and reliability of the solar system, and is expected to promote expanded application of solar systems in the local district. It is a single-crystalline modular system, operated at -20 to 40degC and connected to the low-voltage power transmission line with reverse power flow. It consists of 70 modules, with an array configuration of 5 series, 5 parallel and 2 lines, and 5 series, 4 parallel and 1 line, directed to the due south at the angle of incidence of 20deg. The cell is 103 by 103mm in size, and 96 cells are connected in series. It has a conversion efficiency of 12.7%. The optimum working voltage and current are 45.6V and 3.29A, and the maximum output is 150W. 5 figs., 3 tabs.

New energy technology development related database construction survey (wind power generation); Shin energy gijutsu kaihatsu kankei data shu sakusei chosa (furyoku hatsuden)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

To arrange systematic data relating to new energy, the latest published data relating to the wind energy conversion systems have been collected and arranged. For the overview of wind energy conversion system, wind turbines with horizontal axis and vertical axis, specification of wind turbine, and conceptual figure of wind energy conversion systems are illustrated. For the installation examples, introduction development of wind energy conversion systems in the world is described for Japan, the USA, Germany, Denmark, Spain, Sweden, India, and Belgium. For the relevant legislation and support plan, relevant legislation for the introduction of wind energy conversion in Japan, support plan in Japan, and support plans in foreign countries are described. Prices of wind turbines by wind turbine makers in the world, construction cost by Japanese makers, basic term, and subsidiary company and organization are shown

Application of adaptive control to windmill power system by computer simulation. Simulation ni yoru tekio seigyo no furyoku hatsuden system eno oyo

Energy Technology Data Exchange (ETDEWEB)

Tomiya, T.; Matsuo, T. (Anan College of Technology, Tokushima (Japan)); Suzuki, T.; Kamano, T. (Tokushima University, Tokushima (Japan). Faculty of Engineering)

1991-07-20

A windmill power system using load DC generators having resistive load was subjected to discussions by simulation on development of a control method and its output characteristics to draw out the wind energy effectively even when the system characteristics are unknown. The control method used is a mountaineering method available among adaptive control methods. As a result of discussions, the effectiveness of the mountaineering method was confirmed in controlling the output either when the wind velocity is constant or variable. With respect to the control interval, which is a problem in carrying out a control, it was found that the control output stabilizes as the control interval is increased when the wind velocity is constant, but takes longer time before reaching a steady state output. When the wind velocity is variable, the increased control interval reduces the output slightly because of the load resistance change becoming coarser. It was also revealed that, on simulated natural winds, this control method can draw out more energy than by a fixed load resistance. 7 refs., 11 figs., 1 tab.

Achievement report on the development of solar thermal electric power plant technologies. Annex; Taiyonetsu hatsuden plant gijutsu kaihatsu seika hokokusho. Fuzoku shiryo

Energy Technology Data Exchange (ETDEWEB)

NONE

1985-07-01

The two solar thermal electric power pilot plants are of the tower concentration type and the flat/curved surface concentration type. For the first time in the world, they succeeded in operating at a rated output of 1,000kW in August and September, 1981, respectively. Sunshine was inputted at an unstable rate, and the plants were operated under various load patterns. Studies were conducted and an optimum operating technique is established. Since designing, construction, and operation were carried for two types of pilot plants, quantities of useful data were collected through a variety of experiences. Valuable hints and design data were provided for use in the construction of full-scale power plants in the future. Element units developed for the plants were high-reflectance mirrors, high-precision tracking mechanisms, solar heat collectors of the cavity type and paraboloidal type, and molten salt heat accumulators. The tower concentration type plant exhibits a power generation efficiency of 16-17% and an overall plant efficiency of 3.1-4.4%. The maximum overall efficiency a month is 3.9% with the flat/curved surface concentration type plant. (NEDO)

Application of photovoltaic generating system to electric power in large ship; Taiyoko hatsuden system no ogata senpaku eno oyo ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Katagi, T; Ogawa, S; Nishikawa, E; Hashimoto, T [Kobe University of Mercantile Marine, Kobe (Japan); Ishida, K

1996-10-27

This paper describes the design of electric power system in a ship with photovoltaic power generating system, to examine applicability of the photovoltaic power generating system to the inboard power source. It also discusses effectiveness of the system for sea environment. At first, the actual route of a car carrier, meteorological data, and quantity of power consumption were picked up from the deck logbook and engine logbook. Then, the installation area of photovoltaic arrays, the quantity of photovoltaic power generation derived from the quantity of solar radiation, and the capacities of batteries and inverters were calculated, to design the electric power system in the ship with photovoltaic power generation system. Moreover, the NOx and SOx emissions were compared between the present power system and the usual power system using diesel power generator, to discuss the effectiveness of the present system for sea environment. Consequently, it was found that the emission of NOx was reduced by about 33% and the emission of SOx was reduced by about 28% compared to the usual power system. The effectiveness for sea environment was confirmed. 9 refs., 5 figs., 4 tabs.

Examination of optimal data acquisition for evaluation of PV systems; Taiyoko hatsuden system hyoka no tame no saiteki keisoku shuho no kento

Energy Technology Data Exchange (ETDEWEB)

Sugiyama, H; Kurokawa, K [Tokyo University of Agriculture and Technology, Tokyo (Japan); Otani, K; Tsuda, I [Electrotechnical Laboratory, Tsukuba (Japan)

1996-10-27

A 70 kW-class photovoltaic (PV) power generation system of the Tsukuba Research Cooperation Center, Agency of Industrial Science and Technology was evaluated using hourly measurement data. Hourly solar irradiation, mean PV module temperature, hourly array generated power, hourly PV system generated power were selected as the measurement items, to examine the validity of measurement method. Furthermore, based on these measurement data, the loss factors were estimated, which reduce the system efficiency. They included the losses due to the shadow effect, the deterioration of module efficiency with the raise of temperature, the mismatch of tracking control of the maximum power point, and the reduction of inverter efficiency with the input power phenomena. To estimate these loss factors from hourly measurement data, the system was evaluated by defining characteristic parameters. As a result, it was found that the main factors were the shadow effect and the mismatch loss, which reduce the mean annual output factor of the system to 65%. 3 refs., 6 figs., 1 tab.

FY 2000 report on the results of the development of technology for commercialization of the photovoltaic power system - R and D of evaluation technology of the photovoltaic power system. Separate volume. R and D of the system evaluation technology (Data book on the photovoltaic power system); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu - System hyoka gijutsu no kenkyu kaihatsu (Bessatsu : Taiyoko hatsuden system data shu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of establishing the optimum design and optimum operation technology of various kinds of photovoltaic power system, data were collected to make a data book on various kinds of photovoltaic power system of which the future commercialization is expected. Included in this data book were the monthly report on operation data on demonstrative test facilities at the Hamamatsu site of JQA (Japan Quality Assurance Organization), daily graph of insolation/temperature, monthly graph of wind direction/wind velocity. Further, as the data on the residential use photovoltaic power system, data on the following were summed up: information on the site of installation of the residential use photovoltaic power system (photo information, the state of installation such as sites installed more in FY 2000, drawings of module arrangement and measuring point layout, etc.), daily report on operation (graph of daily trends, daily report by site, hourly report by site, daily report on all sites, hourly report on all sites), operation data and performance indices, list of troubles arising in the residential use photovoltaic power system, other system information about residential use measuring data, power generation characteristics and {alpha}{sub pmax} of residential use solar cell modules, etc. (NEDO)

Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Research and development of photovoltaic power utilizing system and peripheral technologies (Research and development for enhancing reliability of photovoltaic power generation - Research on long-term reliability of inverter); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (taiyoko hatsuden no shinraisei kojo ni kansuru kenkyu kaihatsu - inverter no choki shinraisei no chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

In fiscal 1999, the power conditioner which is the primary component of a photovoltaic power system was subjected to an accelerated test, etc., for the evaluation of its durability. For the accelerated test, operating conditions were so set that acceleration be implemented according to Arrhenius' law at ambient temperature 40 degrees C and relative humidity 36%. For the operation of the power conditioner, it was so set that the operation duration be 3.5 hours with a rest time of 4.5 hours for the night or the like. In the accelerated test conducted as in the previous year, 1100 cycles were completed recording the maximum, equivalent to approximately 8-1/2 years according to Arrhenius' law. After the test, no life affecting changes were detected in specimen device A, B, or D. Specimen C, however, failed during the test. As for the evaluation of durability of components, the electrolytic capacitor in the power conditioner was named. Reliability related literature was investigated and a durability evaluation test was started, with consideration given to the voltage to apply and service temperature. (NEDO)

FY 2001 report on the survey of the formation promotion subsidy project on the environmentally friendly type energy community. Potential survey of the introduction of a processing/power generation system using ASR in the South region of Tochigi Prefecture; 2001 nendo kankyo chowa gata energy komyuniti keisei sokushin hojo jigyo. Tochigi ken nanbu chiiki ni okeru ASR (Shuredda dust) wo nenryo to shita shori hatsuden system no donyu kanosei chosa chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

For the consistent processing of waste automobile in Tochigi Prefecture and the neighboring area, survey/study were made of the thermal recycle using shredder dust, ASR (automobile shredder residue), as fuel as well as the material recycle. As to the amount of material recycle of waste automobile, the amount of potential recycle of iron, copper, plastic, etc. was estimated, and it was found out that the potential recycle of parts such as engine was 40-45%, that of iron scrap 35-40%, and that of ASR 20-25%. The amount of fuel (ASR amount) to be thrown into the gasification power generation system was set up at 150t. As the gasification power generation system, the pyrolysis gasifier and shaft kiln gasification melting furnace were selected. In the study of economical efficiency of the gasification power generation system, the following were considered: ASR processing price, plant cost, subsidy, running cost, char receiving price, power selling price, etc., but even in the case of the pyrolysis gasifier with highest valuation, both payback years and IRR did not reach the target. (NEDO)

Report on the project for spread/promotion of technology for the industrial waste optimized treatment in the Asian region; Asia chiiki sangyo haikibutsu tekiseika shori gijutsu nado fukyu sokushin jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The International Symposium `98 on the industrial waste problem in the Asian region was held in Tokyo on February 18, 1998. MITI commented on the present situation of the industrial waste problem in Japan and Japan`s environmental tackling toward the Asian region, and also Asian countries (China, the Philippines, Thailand and Korea) made reports. Japan reported on environmental preservation measures taken in the industrial circle, the industrial waste problem at companies which advanced into Asian countries, effects of the Basel Convention (which restricts border-crossing movement of harmful wastes) on recycle activities, Japan`s role in Asia, etc. In the panel discussion, discussions were made on human interchange in the informatization, recycling technology, shortage of personnel concerned with environmental protection, construction of a network in the Asian region and Japan` s role, etc. As to the treatment system for waste, the necessity was recognized of studying systems which meet with actual states of each country. It is also necessary to go on with discussing how the system should be for cooperation between governments and private companies. Importance of the recycle and information exchange was emphasized. 10 refs., 14 figs., 27 tabs.

Report on achievements in fiscal 1998. Development of technologies to put photovoltaic power generation systems into practical use (International cooperation project - collection of information on IEA photovoltaic power generation program); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Kokusai kyoryoku jigyo (IEA taiyoko hatsuden program ni kansuru joho shushu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Research and development, verification, analysis and information exchange have been performed based on the 'Treaty to Execute the Research and Cooperation Program on Photovoltaic Power Generation System'. The IEA/REWP/PVPS activities in fiscal 1999 include the participation to the two executive committee meetings (Valencia and Sydney), and the subcommittee activities. The subcommittee activities are as follows: Task I: information exchange on and proliferation of the photovoltaic power generation systems, Task II: operation performance and design of the photovoltaic power generation systems, Task III: design and operation of the independent type and the island use power plants, Task VII: Building integrated photovoltaic power generation systems, Task VI, Sub-task 5: investigations and researches on possibility for photovoltaic power generation systems utilizing unutilized lands including deserts, and Task IX: technical cooperation to expand photovoltaic power generation system markets. (NEDO)

Report on achievements in fiscal 1998. Development of technologies to put photovoltaic power generation systems into practical use (International cooperation project - collection of information on IEA photovoltaic power generation program); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Kokusai kyoryoku jigyo (IEA taiyoko hatsuden program ni kansuru joho shushu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Research and development, verification, analysis and information exchange have been performed based on the 'Treaty to Execute the Research and Cooperation Program on Photovoltaic Power Generation System'. The IEA/REWP/PVPS activities in fiscal 1999 include the participation to the two executive committee meetings (Valencia and Sydney), and the subcommittee activities. The subcommittee activities are as follows: Task I: information exchange on and proliferation of the photovoltaic power generation systems, Task II: operation performance and design of the photovoltaic power generation systems, Task III: design and operation of the independent type and the island use power plants, Task VII: Building integrated photovoltaic power generation systems, Task VI, Sub-task 5: investigations and researches on possibility for photovoltaic power generation systems utilizing unutilized lands including deserts, and Task IX: technical cooperation to expand photovoltaic power generation system markets. (NEDO)

FY 1999 Report on the technical results. Part 2-1. Development of fuel cell power generation technologies (Research and development of molten carbonate fuel cell power generation system); 1999 nendo nenryo denchi hatsuden gijutsu kaihatsu seika hokokusho. 2-1. Yoyu tansan'engata nenryo denchi (hatsuden system no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

This research and development project is aimed at modification and improvement of the stacking technologies, to improve service life and performance of the molten carbonate fuel cell power generation system and reduce its cost. For the cross-flow type stack, optimization of the anode firing conditions leads to controlled reduction of the fine pores, and incorporation of the cathode with MgO successfully leads to controlled elution of NiO and Ni short-cut. For the separator, the service life is extended by treatment of the material with Al and controlling its rigidity. The cell life prediction method is improved to enhance its accuracy. The cell life of -4.3mV/1,000h is achieved by these technologies. For the parallel-flow type stack, the electrodes are improved to achieve the cell life of -1.4mV/1,000h, the technologies for producing the separator for a 1m{sup 2} class unit are developed, and the basic structures of a large-capacity stack are designed. For the internal reforming type, a 200kW class reforming stack is constructed, and operated for 5,259 hours. The causes for electrolyte loss are analyzed by developing the relationships between operating temperature and electrolyte loss, electrolyte mass and sustainability of the cell characteristics, and steam partial pressure over the cathode and electrolyte loss, and also by testing the Ni short-cut. (NEDO)

Research and development of photovoltaic power system. Interface studies of amorphous silicon; Taiyoko hatsuden system no kenkyu kaihatsu. Amorphous silicon kaimen no kenkyu

Energy Technology Data Exchange (ETDEWEB)

Konagai, M [Tokyo Institute of Technology, Tokyo (Japan). Faculty of Engineering

1994-12-01

This paper reports the result obtained during fiscal 1994 on research on interface of amorphous silicon for solar cells. In research on amorphous solar cells using ZnO for transparent electrically conductive films, considerations were given on a growth mechanism of a ZnO film using the MOCVD process. It was made clear that the ZnO film grows with Zn(OH)2 working as a film forming species. It was also shown that the larger the ZnO particle size is, the more the solar cell efficiency is improved. Furthermore, theoretical elucidation was made on effects of rear face of an interface on cell characteristics, and experimental discussions were given subsequently. In research on solar cells using hydrogen diluted `i` layers, delta-doped solar cells were fabricated based on basic data obtained in the previous fiscal year, and the hydrogen dilution effect was evaluated from the cell characteristics. When the hydrogen dilution ratio is increased from zero to one, the conversion efficiency has improved from 12.2% to 12.6%. In addition, experiments and discussions were given on solar cells fabricated by using SiH2Cl2. 9 figs.

Data book on new energy technology in FY 1997. Wind power generation; Shin energy gijutsu kaihatsu kankei data shu sakusei chosa. Furyoku hatsuden

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

It is an urgent necessity for Japan to promote the technological development and accelerate the introduction and diffusion of new energy. In order to diffuse and enlighten the introduction of new energy technology efficiently, it is necessary to compile various information regarding new energy in a comprehensive and systematic way, and formulate a database. Aiming at the systematic formulation of data on new energy, this survey focuses on the field of wind power generation system (WPS) and provides a collection of the latest published data on WPS, particularly regarding the worldwide installed wind power capacity, support plan and government policies, current situations of WPS market, and major technical characteristics of typical wind turbines. This report consists of the significance of wind energy, world market of wind turbines, government policies, international wind energy development, subsidies for wind energy, procedures of wind turbine system installation, governmental measures for wind energy development, subsidiary companies and organizations, basis of wind energy, and Japan`s wind energy development in 1997

Photovoltaic power generation field test at Nisshin Techno-Center (Nisshin City, Aichi Prefecture); Nisshin tekuno center taiyoko hatsuden field test jigyo (Aichiken Nisshinshi)

Energy Technology Data Exchange (ETDEWEB)

Otsuki, M. [Meitec Corp., Nagoya (Japan)

1997-05-30

A 20kW system is installed on the rooftop of a newly constructed building accommodating a study and training center and citizens` welfare facilities. The system in continuous operation under real loads (lighting, airconditioning) will provide various data useful in introducing further systems in the future and in verifying the effect of system installation cost reduction efforts. Single-crystal solar cells are used, which are located at latitude 35deg8prime north, longitude 137deg4prime east. The arrays are formed into two systems, 18 in series and 7 in parallel, and there are 252 modules. The arrays are inclined at 20deg and, in azimuth, swung 25deg westward from due south. The installation of this system forms a precedent, following which more may be introduced. Located in front of a station on Meitetsu Toyota Line, it advertises itself fully to the passengers getting on and off the train. Now that power consumption fluctuates very much in this district, heavy on Saturdays and Sundays and light in the daytime on weekdays, rare data not often available will be collected from this photovoltaic system. Since consideration space-wise has been fully made, visitors can study the photovoltaic system until they are satisfied, the system thus finding itself under conditions where advertisement can be effectively carried out. 14 figs., 1 tab.

Photovoltaic power generation field test at Kyodo Newspaper Co. Ltd. (Kakegawa city, Shizuoka prefecture); Kyodo shinbunsha taiyoko hatsuden field test jigyo (Shizuokaken Kakegawashi)

Energy Technology Data Exchange (ETDEWEB)

Totsuka, T.

1997-05-30

Contents are reported of the fiscal 1996 field test of a photovoltaic power generation system installed on the roof surfaces of the parking lot of the above-named newspaper company. The system is used to supply power to the lights in the company office and to a light sign tower for local activities promotion (erected jointly by cities and towns in the neighborhood). It is a 10kW plant operating on system interconnection, provided with an array of 9-series/11-parallel configuration facing due south and inclined at an elevation angle of 15deg. It is so designed that solar cell mounts are installed on two roof surfaces so that space will be secured for the parking lot. The above-mentioned LED-aided light sign tower serves the purpose of informing people of photovoltaic power generation technology and the culture, history, and industry of the local communities involved. Basic data have been collected usable for standardizing the design for example of the mount for the establishment of guidelines for reduction in the system construction cost. Data have been also obtained that will help make propositions about the effective utilization of dead space outdoors. Since the system is installed making use of roof surfaces without affecting parking lot capacity, people`s understanding of the technology has been deepened and data of long-term operation following the experimental introduction and troubles have been collected, all these helping encourage the introduction of photovoltaic power generation

Improvement of adaptive fuzzy control for a photovoltaic/wind/diesel generating system; Taiyoko/furyoku/diesel hatsuden system no saitekigata fuzzy seigyo no kairyo

Energy Technology Data Exchange (ETDEWEB)

Nagaike, H; Kenmoku, Y; Sakakibara, T [Toyohashi University of Technology, Aichi (Japan); Nakagawa, S [Maizuru National College of Technology, Kyoto (Japan); Kawamoto, T [Shizuoka University, Shizuoka (Japan).Faculty of Engineering

1996-10-27

The photovoltaic/wind/diesel generating system that uses a storage battery as auxiliary power has been proposed to supply power from the system to the independent area. In this system, it is important to generate no insufficient power from the viewpoint of effective energy utilization and minimize the fuel consumption of a diesel generator. Authors have proposed the adaptive fuzzy control that changes the shape of the membership function of input variables according to the parameter indicating the system state. However, a parameter was rapidly changed in the conventional method. This badly influences the control. Therefore, the way to determine the parameter that indicates the state of this system was improved. Assume that an input value is set to the average value between a certain point of time and the {Delta}t time as the method for determining a parameter. If the {Delta}t value is lower, the change in a membership function is more effective. As a result, a greater fuel reduction effect was obtained. 4 refs., 8 figs., 1 tab.

Fiscal 1998 research report. Popularization project of the proper treatment technology of industrial wastes in Asian regions; 1998 nendo chosa hokokusho. Asia chiiki sangyo haikibutsu tekiseika shori gijutsu nado fukyu sokushin jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Study was made on popularization of the proper treatment technology of industrial wastes in Asian regions. In principle, industrial wastes should be recycled in a country concerned, however, because of a difference in technology and industrial location, treatment of all industrial wastes in a country concerned is impossible. International cooperation is thus indispensable to promote proper efficient practical measures for environment. For studying the possibility of the international cooperation between Japan and Asian countries concerned for further recognition and solution of industrial waste problems, 'International Symposium on the Asian Industrial Waste Issue' have been held in Tokyo since 1997 for governmental staffs. In fiscal 1998, Malaysia was invited in addition to China, Philippines and Thailand for popularization of the proper treatment and recycling of industrial wastes in Asian regions. In every Asian countries, poor collection of discharge, treatment and disposal data is an obstacle to effective treatment. Technical cooperation and financial support by developed countries are demanded. (NEDO)

Mixture of industrial waste oxidized titanium and reduced slag from electric furnace used as hydraulic material. Denkiro kangen slug to sanka titan kogyo haikibutsu no kongobutsu no suinan zairyo to shiteno riyo

Energy Technology Data Exchange (ETDEWEB)

Honda, A [Osaka City University, Osaka (Japan). Faculty of Engineering; Kuwayama, T [Daido Institute of Technology, Nagoya (Japan); Yamada, M; Ikezaki, H [Osaka City University, Osaka (Japan). Faculty of Engineering

1990-10-29

Slag released from an electric furnace consists mainly of waste steel. There are two types of slag, namely, oxidized slag and reduced slag. Reduced slag, which is generally in the form of powder, is difficult to recycle as compared with oxidized slag. However, with a hydraulicity, some reduced slag is expected to be useful as hydraulic material. Test results obtained here show that the hydraulic properties of reduced slag powder can be improved by mixing it with gypsum and that the resultant mixture can serve to improve the prooperties of soft clay. Another study is made to determine the potential, as hydraulic material, of mixtures of reduced slag powder and waste gypsum material with a high gypsum content released from an oxidized titanium production process. The hydraulicity is found to develop as a result of the formation of a hydrate of calcium aluminate which is contained in the slag. Addition of water to the hydrate and gypsum cause the formation of ettringite, leading to an increased uniaxial compressive strength. These findings indicate that the above-mentioned mixture can be useful to improve the hydraulic properties of coal ash to be disposed of at landfill sites. 5 refs., 5 figs., 1 tab.

Fiscal 1998 research report. Popularization project of the proper treatment technology of industrial wastes in Asian regions; 1998 nendo chosa hokokusho. Asia chiiki sangyo haikibutsu tekiseika shori gijutsu nado fukyu sokushin jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Study was made on popularization of the proper treatment technology of industrial wastes in Asian regions. In principle, industrial wastes should be recycled in a country concerned, however, because of a difference in technology and industrial location, treatment of all industrial wastes in a country concerned is impossible. International cooperation is thus indispensable to promote proper efficient practical measures for environment. For studying the possibility of the international cooperation between Japan and Asian countries concerned for further recognition and solution of industrial waste problems, 'International Symposium on the Asian Industrial Waste Issue' have been held in Tokyo since 1997 for governmental staffs. In fiscal 1998, Malaysia was invited in addition to China, Philippines and Thailand for popularization of the proper treatment and recycling of industrial wastes in Asian regions. In every Asian countries, poor collection of discharge, treatment and disposal data is an obstacle to effective treatment. Technical cooperation and financial support by developed countries are demanded. (NEDO)

Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Research and development of photovoltaic power utilizing system and peripheral technologies (Research and development for enhancing reliability of photovoltaic power generation - Research on environmental measures for compound solar cell modules); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (taiyoko hatsuden no shinraisei kojo ni kansuru kenkyu kaihatsu - kagobutsu taiyo denchi module no kankyo taisaku no chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Research is conducted to properly deal with environmental problems, such as compromised solar cell safety, which may follow the mass introduction and diffusion of photovoltaic power systems. In the research of fiscal 1999 on technical literature on environmental measures against lead and animal tests, a need was found to reduce lead in power systems and to grasp lead elution characteristics for the establishment of environmental measures. In a safety test conducted for thin-film CIS (copper indium diselenide) based solar cells, basic data were collected about the vaporization rate of Se, the effect of moisture on the Se vaporization rate, etc. Basic data were also collected about the relationship between the combustion temperature and the amount of scattered lead in particular from the solder used as the conducting material in silicon based solar cells. In the evaluation of the environmental impact of thin-film CIS solar cells in case of fire, it was found that Se concentration below 10-20m in the plume was near the permissible concentration of 0.1mg/m{sup 3} as recommended by Japan Society for Occupational Health and that the concentration levels predicted for the periphery were two orders of magnitude smaller than the mandatory level. (NEDO)

FY 1998 report on the results of the New Sunshine Project - Development of the commercialization technology of the photovoltaic power system. Verification study of the photovoltaic power system - Research on engineering methods for cost effective PV installation (Data book. Survey of examples of PV systems in the world); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden system no jissho kenkyu (tashu secchi koho no kenkyu kaihatsu (bessatsu data shu sekai no taiyoko hatsuden system jirei chosa))

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For the purpose of promoting installations of PV system and making use of the unused space for which a rise in the PV demand equal to that in houses, building roofs, etc. is expected, examination/research for much newer forms of land installation are proceeded with, and evaluation/verification of reliability/durability are conducted of new installation processes using thin film solar cells, adhesives, etc. In this fiscal year, for the purpose of contributing to the study to be widely made on various installation processes, the actual survey was conducted of various applications of the system which are being planned and introduced in Japan and abroad. Emphasis was placed on making new forms of installation applicable to Japan clear. Concretely, in addition to the study of new examples, the following were conducted: renewal of existing details of the survey, and electronic filing of system block charts/pictures as a key to the information supply by electronic media such as CD-ROM. Also conducted was a study for translating the contents into English or writing them both in Japanese and English. Further, the database was made newer using these results of the most up-to-date survey, and at the same time, the results were indicated of the statistical analysis of the usage, system form, power generation scale and element equipment of various systems. (NEDO)

FY 1998 Report on development of large-scale wind power generation systems. Feasibility study on development of new technologies for wind power generation, and study on local wind resource prediction model; 1998 nendo ogata furyoku hatsuden system kaihatsu seika hokokusho. Furyoku hatsuden shingijutsu kaihatsu kanosei chosa (kyokusho fukyo yosoku shuho ni kansuru chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Described herein are the FY 1998 results of the study on local wind resource prediction model. The local wind resource prediction models developed so far apply the solutions based on the existing linear models (WASP and AVENU) for relatively flat terrain. These models are studied for their applicability limits. The study covers wind direction and speed patterns of the surface wind and upper winds at 3 sites in Hokkaido, Fukushima Pref. and Shizuoka Pref. The surface winds are found to be correlated with the upper winds both for wind direction and wind speed in almost all cases. Next, wind resources simulations are carried out for each of the classified weather patterns using the existing models, and the prediction errors are studied. The results show that the prediction accuracy of the existing linear models is highly dependent on inputs of observed data, and that the accuracy tends to decrease for the situations where the upper and surface wind conditions greatly differ from each other, as in the case of a land and sea breeze of thermal origin. It is also confirmed that prediction accuracy is lower on complex terrain than on flat terrain. (NEDO)

Sunshine Program-assisted project achievement report for fiscal 1981 on the development of technologies for photovoltaic power system practical application. Development of photovoltaic power generation demonstration system (Research and development for schoolhouses); 1981 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden demonstration system kaihatsu (gakkoyo system no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Power generated by solar cells complying with NEDO (New Energy and Industrial Technology Development Organization) specifications is stored in a storage battery or is converted into AC power in a DC-AC converter for interconnection with a commercial power system, and then supplied to loads in schoolhouses. The system operates independently when the commercial power system is out. Basic plans and primary specifications had been determined, basic modules experimentally built, tested, and part of their details designed, all these up to fiscal 1980. In fiscal 1981, system design details are drawn, housetops are examined for installation, and problems that may entail installation are checked. A system data accumulation unit comes into operation for data collection. A system simulator is developed and constructed and the solar cell is checked for performance. Model arrays are built and subjected to a combination tests, when the effect of shade is also investigated. A charge control unit, high-efficiency GTO (gate turned-off) thyristor DC-AC converter, and a protection circuit in preparation for interconnection are developed, and experimentally constructed. In fiscal 1982, 20kW solar cells will be installed and schoolhouse systems will come into service operation. (NEDO)

Achievement report for fiscal 2000 on New Sunshine Project aiding program. Development of hot water utilizing power generation plant (Technological development of hot rock power generation system - development of elementary technologies); 2000 nendo nessui riyo hatsuden plant to kaihatsu seika hokokusho. Koon gantai hatsuden system no gijutsu kaihatsu (yoso gijutsu no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In order to identify the possibility of a hot rock power generation system, technological R and D has been performed on structuring of a man-made hydrothermal system, fracture mapping, downhole measurement and a circulating extraction system. This paper summarizes the achievements in fiscal 2000. With regard to the long-term circulating extraction test, a circulating heat extraction and test device was installed at the hot rock experimental field in the Hijiori area in Yamagata Prefecture, where geochemical data collection and tests including analyses thereon have begun. In reservoir bed analysis, a well module was incorporated into a reservoir bed simulator to improve the module so that comparison with the data of actual production on the ground can be performed. For the fracture mapping, AE having been observed during the long-term circulation test was analyzed, whereas it was estimated that the seismic source would not move or expanded during this period. A PTS logging has been performed during the long-term circulation test to investigate characteristics of the flow-out zone of the injection well and the production zone of the production well. In making the fracture model, an initial model was fabricated to estimate heat extraction behavior in the long-term circulation test. (NEDO)

Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. International cooperation projects (Collection of information on Task 9 in IEA photovoltaic power generation program); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Kokusai kyoryoku jigyo (IEA taiyoko hatsuden program task IX ni kansuru joho shushu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This paper reports activities performed by the Task 9 in the execution treaty of the IEA photovoltaic power generation system program. The Task 9 calls for the 'proliferation of photovoltaic power generation technologies under coordination with developing countries{sup .} It is intended to compile the recommendation guides, hold workshops in the model developing countries, and coordinate with assisting organizations on technological and economical issues that may occur when introducing photovoltaic power generation systems into developing countries. The current fiscal year is the first year of the five-year plan, whereas, with structuring the basic plan placed in the center, such activities were carried out as verification of the 12 member countries and two organizations, establishment of the basic programs for the work plan, selection of work divisions, the sharing thereof, and the subjected developing countries, and the way the coordination should be with the related tasks and the assisting organizations. Two expertise conferences were held in Holland and America, and three working group meetings in Japan to have discussed the activity targets in the first fiscal year. (NEDO)

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Research and development of photovoltaic system evaluation technology (Research and development of system evaluation technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu (system hyoka gijutsu no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In relation with several types of standard photovoltaic power generation systems expected to be put to practical use, design parameters are quantified, databases are utilized, and simulation technologies are developed, while collecting data from test facilities constructed to simulate them, for the development of evaluation techniques indispensable for the efficient improvement of photovoltaic power generation systems. In fiscal 1998, data were collected from verification test facilities and residential photovoltaic systems sited across Japan. The collected data were subjected to analysis and simulation, by which correction factors were calculated for smudge, spectral response, incident radiation, and temperature. Furthermore, load matching factors and storage battery contribution rates were calculated by simulation for the stand-alone photovoltaic systems sited in five Japanese cities, each comprising an array, storage battery, charge/discharge controller, DC-DC converter, and a load. Reference is also made to a survey of trends of technology development. (NEDO)

Report on achievements in technological development in fiscal 1999. Development of technology to put photovoltaic power generation system into practical use (Research and development of high reliability storage batteries for photovoltaic power generation use); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Kenkyu kaihatsu kanri (taiyoko hatsuden'yo chikudenchi kaihatsu bukai)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

Storage batteries used in household photovoltaic systems must be free of electrolyte leakage and maintenance, and be readily installable in residential houses. Lead-acid batteries that can meet these requirements and have been put into practical use may include the sealed storage batteries. However, these batteries currently in use have drawbacks in life performance and price. Therefore, development is under way on lead-acid batteries for household photovoltaic systems by improving said sealed lead-acid batteries. The targeted batteries should have as long life as passing 3,000 cycles under a condition of 0.1 to 1 CA discharge (at depth of discharge of 50%), energy density of more than 70 Wh per liter, and cost of 12 yen or lower per watt-hour. A prototype battery as the final candidate was fabricated, that uses silica powder as the electrolyte retainer (silica powder filled between plates, and into clearance between plate groups), pasted plates made of expanded metal grids for positive plates, and micro conductive network plates with increased addition amount of carbon to micro active material (PbO{sub 2}) as negative plates. Life performance testes thereon are being performed. This lead-acid battery is estimated to be capable of satisfying the intended performance based on the result of discussions having been made so far. (NEDO)

Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. International cooperation projects (Collection of information on Task 9 in IEA photovoltaic power generation program); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Kokusai kyoryoku jigyo (IEA taiyoko hatsuden program task IX ni kansuru joho shushu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This paper reports activities performed by the Task 9 in the execution treaty of the IEA photovoltaic power generation system program. The Task 9 calls for the 'proliferation of photovoltaic power generation technologies under coordination with developing countries{sup .} It is intended to compile the recommendation guides, hold workshops in the model developing countries, and coordinate with assisting organizations on technological and economical issues that may occur when introducing photovoltaic power generation systems into developing countries. The current fiscal year is the first year of the five-year plan, whereas, with structuring the basic plan placed in the center, such activities were carried out as verification of the 12 member countries and two organizations, establishment of the basic programs for the work plan, selection of work divisions, the sharing thereof, and the subjected developing countries, and the way the coordination should be with the related tasks and the assisting organizations. Two expertise conferences were held in Holland and America, and three working group meetings in Japan to have discussed the activity targets in the first fiscal year. (NEDO)

Achievement report for fiscal 1998 on development of power generation using fuel cells. Research and development of molten carbonate fuel cell (II-2, text of the achievement); 1998 nendo nenryo denchi hatsuden gijutsu kaihatsu seika hokokusho. Yoyu tansan'engata nenryo denchi hatsuden system no kenkyu kaihatsu (II-2, kenkyu seika no honbun)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

The effort aims at developing a 1000kW-class power plant and also at using gasified coal as fuel in the future. The fuel system facilities include a high-temperature blower. The exhaust heat recovery facilities comprise a heat recovery steam generator (HRSG) and a turbine compressor. As for the electrical system facilities, an inverter is installed, tested, and adjusted. Control system facilities are also tested and adjusted. In relation with the operation of the plant, coordination is conducted about technological and process-related matters with the Kawagoe thermal power station of Chubu Electric Power Co., Inc., where the fuel cell power plant is to be constructed, which is for the smooth execution of a test run. Ceramic-based cathode materials are being developed, which is for the fabrication of stacks improved in performance, higher in current density, longer in life, and lower in cost. Also exerted are efforts at developing multiple-function electrolyte plates and metallic materials (for example for separator plating). The extent of the acceptability of impurities concentration and gas refining systems are also under study, which is to prepare for future coal gasification. Reference is also made to the study of a total system. (NEDO)

Achievement report for fiscal 1998 on development of power generation using fuel cells. Research and development of molten carbonate fuel cell (II-2, text of the achievement); 1998 nendo nenryo denchi hatsuden gijutsu kaihatsu seika hokokusho. Yoyu tansan'engata nenryo denchi hatsuden system no kenkyu kaihatsu (II-2, kenkyu seika no honbun)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

The effort aims at developing a 1000kW-class power plant and also at using gasified coal as fuel in the future. The fuel system facilities include a high-temperature blower. The exhaust heat recovery facilities comprise a heat recovery steam generator (HRSG) and a turbine compressor. As for the electrical system facilities, an inverter is installed, tested, and adjusted. Control system facilities are also tested and adjusted. In relation with the operation of the plant, coordination is conducted about technological and process-related matters with the Kawagoe thermal power station of Chubu Electric Power Co., Inc., where the fuel cell power plant is to be constructed, which is for the smooth execution of a test run. Ceramic-based cathode materials are being developed, which is for the fabrication of stacks improved in performance, higher in current density, longer in life, and lower in cost. Also exerted are efforts at developing multiple-function electrolyte plates and metallic materials (for example for separator plating). The extent of the acceptability of impurities concentration and gas refining systems are also under study, which is to prepare for future coal gasification. Reference is also made to the study of a total system. (NEDO)

Report on achievement in developing fuel cell power generation technology in fiscal 1998. Research and development of molten carbonate fuel cell power generation system (Summary of the research result); 1998 nendo nenryo denchi hatsuden gijutsu kaihatsu seika hokokusho. Yoyu tansan'engata nenryo denchi hatsuden system no kenkyu kaihatsu (kenkyu seika no yoyaku)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

Based on the achievement made in the second term plan of researching and developing a molten carbonate fuel cell power generation system, attempts are made on extending the service life, improving the performance, and reducing the cost. At the same time, lamination, cooling and operation technologies will be established, and a 1000-kW class power generation plant will be developed. Realization of use of coal gasified fuel in the future is aimed. Stack materials and their processing technologies will be developed, the cell durability will be improved, and the total system research will be carried out. This paper describes the achievements made during fiscal 1998. A process and control (PAC) test was performed on the fuel system facilities in the 1000-kW class generation plant, and its result was analyzed. The fuel system facilities had the test program using simulated fuel cells set from the system side digested nearly completely, verifying that actions can be taken for operation using actual fuel cells to be executed in fiscal 1999. Analysis of the test result presented raw material conversion rate of 96.6% or higher, generation of hydrogen plus CO of 740 m{sup 3} N/h, and NOx generation of 10 ppm or less. Stable combustion of a low calorie gas (500 kcal/m{sup 3} N) was achieved, completing all of the research objectives planned for fiscal 1998. (NEDO)

Fiscal 1995 report on the survey of making models for introducing petroleum substituting energy systems. 2; 1995 nendo chosa hokokusho (sekiyu daitai energy system donyu model sakusei ni kansuru chosa). 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

In the promotion of measures taken for energy conservation, it is necessary to give local governments, entrepreneurs, etc. guidance for introducing energy systems which meet with features of the buildings and courses for how to construct infrastructures of towns or cities in case of development, redevelopment, etc. In fiscal 1995, each of the petroleum substituting energy systems was studied more detailedly, and the trend of building facilities for the introduction was studied and arranged. Energy systems by the following were set up paying attention to energy sources, energy conversion and energy transportation as factors composing a petroleum substituting energy system: photovoltaic power generation, use of solar energy, use of wind energy, use of geothermal energy, use of biomass energy, use of waste, use of temperature difference energy, cogeneration, load levelling, wide-area energy supply, etc. Also studied and arranged were energy demand, location, the recent trend, the point of introduction of energy systems, examples of introduction, etc. in relation to indoor sport facilities, hospitals, hotels, multiple dwelling apartments, commercial facilities, offices, plants, etc. 52 figs., 55 tabs.

Report on survey in fiscal 2000. Survey on introduction of external accreditation system in engineer education (information); 2000 nendo chosa hokokusho. Gijutsusha kyoiku no gaibu ninteiseido donyu ni kansuru chosa (Joho)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In order to ensure international applicability of engineer education such as in universities and other organizations, and to improve the environment to supply human resources demanded by economic societies, surveys and discussions were performed on the external accreditation system for engineer education such as in universities and other organizations. In the survey on the information field, a trial was attempted on the information related course at Kyoto University and Osaka University based on the accreditation criteria discussed with an objective of establishing the external accreditation system. The trial was performed on computer science for Kyoto University and software engineering for Osaka University. The activity has provided the examiner side with an opportunity to actually experience the accreditation work, and the examiners had a feeling that the work can help improve the education. The side receiving the accreditation indicated problems in the present system including the concern about the system becoming a mere shell. In addition, participation in the accreditation examiner training work for the information field in the U.S.A. has provided useful information such as thoroughgoing observation of the duty of confidentiality. (NEDO)

Report on survey in fiscal 2000. Survey on introduction of external accreditation system in engineer education (general); 2000 nendo chosa hokokusho. Gijutsusha kyoiku no gaibu ninteiseido donyu ni kansuru chosa (Zentai)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In order to ensure international applicability of engineer education such as in universities and other organizations, and to improve the environment to supply human resources demanded by economic societies, trials and discussions were performed on the external accreditation system for engineer education such as in universities and other organizations. The current fiscal year has performed the trials of examination and accreditation at 19 universities and for 20 programs covering eight fields including chemistry, machinery, civil engineering, electrical, electronic, information communications, information processing, materials, resources and agricultural engineering. In performing the trials, the purpose and the basic policies were identified, the guidebook for actual examinations was prepared, and the program check book and the trial examination report were also compiled. Two assembly training meetings were held to train about 130 examiners, of which 65 examiner chiefs and examiners have participated in the trials for 20 schools to work for the examination. As a result of the trials, the training was found capable of having served for improvement of the engineer education program in high-level education institutions, and improvement of the accreditation criteria and examination methods to establish the external accreditation system. (NEDO)

Surveys on awareness and needs of industries to external accreditation system in engineer education; Gijutsusha kyoiku no gaibu ninteiseido donyu ni taisuru sangyo kai no ioshiki to needs ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In certifying the engineer educational programs at advanced educational organizations, questionnaire and visiting surveys were performed to identify the awareness and needs of industries, and reflect the results to the external accreditation system. The questionnaire survey was conducted on 1,100 engineers acting in the wide technical areas. Effective replies were obtained from 528 engineers. The visiting survey was executed on different business areas and operations. The result of the survey revealed that, in the awareness related to international universality of the engineer education and engineer qualification, 87% answered that they feel they need them, but the cognition rate on the accreditation system has not reached even 50%. In hearing the opinions from representatives in the industries, they indicated that it is not correct to link the certification course of JABEE directly to the engineer qualification; international applicability of JABEE with America is fine, but defining the engineers who desire to come from Asian countries and work in Japan is necessary; the engineer education has its importance shifting from quantity to quality and specialization, but on the other hand diversity is also demanded; and criteria would be necessary to guarantee the minimum required knowledge and capability. (NEDO)

Fiscal 1997 survey report. Preparatory survey for a manual on the introduction of high efficiency thermal utilization systems; 1997 nendo chosa hokokusho. Kokoritsu netsu riyo system donyu manual no sakusei choa

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

To cope with the energy issue and global environmental issue, it is necessary to forcibly promote energy conservation. In the light of the present situation that in Japan only 1/3 of the primary energy consumed is effectively used, policies are being prepared for promotion of the introduction of high efficiency thermal utilization systems including `a project for formation of the environmentally friendly type energy community` promoted by NEDO. However, it is hard to say that the introduction is being actively promoted. The cause is that they do not fully understood the present status of high efficiency thermal utilization systems, procedures for introduction, subsidy system, etc. Therefore, a manual was made to present to self governments and enterprisers who are planning to introduce the system. To be concrete, there are the six systems: cogeneration use thermal supply system, unused energy use thermal supply system, heat storage use thermal supply system, waste use thermal supply system, plant surplus energy use thermal supply system, and cascade type thermal supply system. 28 refs., 38 figs., 42 tabs.

Research and development of photovoltaic power system. Optimization of bandgap of chalcopyrite semiconductors; Taiyoko hatsuden system no kenkyu kaihatsu. Kinseitaihaba no saitekika no kenkyu

Energy Technology Data Exchange (ETDEWEB)

Konagai, M [Tokyo Institute of Technology, Tokyo (Japan). Faculty of Engineering

1994-12-01

This paper reports the result obtained during fiscal 1994 on research on research on optimization of bandgap in thin film compound solar cells. In research on Cu(InGa)Se2 thin film solar cells by using a gas phase selenide making process, discussions were given on optimizing the following three processes: a process to raise temperature of a precursor film formed at a substrate temperature of about 150{degree}C, a selenide making process to perform annealing at about 500{degree}C, and a temperature reducing process. Good characteristics were obtained when selenium amount in the precursor is about 50%. In a bandgap control viewpoint, it was found that the conversion efficiency decreases rapidly when Ga composition is higher than 50%. A conversion efficiency of 14.9% was obtained to date at the Ga/(In+Ga) ratio of 0.4. In research on Cu(InGa)Se2 thin film solar cells by using a simultaneous deposition method, a conversion efficiency of 13.5% was obtained at a bandgap width of about 1.3 eV during research on manufacturing ZnO/CdS/Cu(InGa)Se2 thin film solar cells by using the simultaneous deposition method. Research has been carried out on manufacturing Cu(InGa)Se2 thin film solar cells using ZnSe interface layers. 8 figs.

Wind energy technology : from the past to the future; 20 seiki ni okeru furyoku riyo gijutsu no henkan. Furyoku hatsuden : kako kara mirai e

Energy Technology Data Exchange (ETDEWEB)

Ushiyama, I. [Ashikaga Institute of Technology, Tochigi (Japan)

2000-01-20

Windmills are one of the oldest prime movers and have been used for more than 700 years in Europe. The transition from low speed windmills for grain grinding and water pumping to high speed wind turbines for electric power generation had occurred at first, reviews the windmill technologies and the researchers before 20{sup th} century. Then describes the back ground of how the wind power generator has existed and how the four pioneers developed their wind power generator. The historical developments of windmills to wind turbines in this century are studied focusing mainly on Danish activities. Then, the effort of the development of large wind turbine such as Smith-Putnum's first MW machine in U.S.A. and other mammoth machine concept are introduced. The new concept machines such as Savonius and Darrieus wind turbines in 1920s to 1930s are also explained. Finally, the novel technologies of wind turbine covering larger machines, variable speed generators, special wing sections for wind turbines, theoretical analysis method of wind turbine performance, offshore wind turbines, and wind turbine control technologies are stated. (author)

Reduction mechanism of dynamic loads on down wind rotor; Furyoku hatsuden system down wind rotor no doteki kaju no keigen kiko ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Seki, K; Shimizu, Y; Yasui, T [Tokai University, Tokyo (Japan)

1997-11-25

Dynamic force on blades in a large wind mill changes with rotational speed for various reasons, such as wind shear that causes vertical distribution of wind velocity or titling angle. Therefore, a 2-blade system on a teetered hub is a practical selection for the coned, down-wind type. Use of teetered axis greatly reduces bending moment in the flap direction and that at the axis of rotation. An attempt was made to understand dynamic loads by inertial force resulting from oscillation of the blade rotating on the teetered axis, and thereby to avoid them. The in-plane load can be diminished to zero when the teetered axis is coincided with the center of gravity, but generally cannot be avoided when the blade is strained significantly, except it is operated at the rated condition. The in-plane load and bending moment can be avoided, when rotational freedom is given around the y axis. Dynamic load on a down-wind rotor can be avoided by use of universal joint. 3 refs., 6 figs.

Starting and stopping control on power conditioner in photovoltaic power system; Taiyoko hatsuden system ni okeru power conditioner no kido teishi seigyo ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Hirose, M.; Ishihara, Y.; Todaka, T.; Harada, K. [Doshisha University, Kyoto (Japan); Oshiro, H.; Nakamura, H. [Japan Quality Assurance Organization, Tokyo (Japan)

1997-11-25

Studies are made about the control of the power conditioner over the maximum power point tracking (MPPT) function in a photovoltaic power generation system. The analysis is conducted by means of computer simulation into the effect of a start/stop function added to the control of MPPT and the effect on the generation of power of the setting of parameters in the start/stop function. The reduction in output power due to difference between the actual operation point and the optimum operation point is evaluated by use of a load matching correction factor. In this simulation, it is assumed that the solar cell array consists of 13 rows in 5 parallel columns, is capable of a normal output of 3.149kW, has a panel tilted at 30 degrees, and faces due south. The power conditioner is assumed to be a system rated at 3kVA, equipped with system interconnection and back flow features. As a result, it is learned that the stop voltage should be set at 180V or lower and the steady voltage near 185.5V for a good result and that there is not much need after all for the start/stop technique. 2 refs., 8 figs., 2 tabs.

Thermochemical recuperative combined cycle with methane-steam reforming combustion; Tennengasu kaishitsu nensho ni yoru konbaindo saikuru hatsuden no kokoritsuka oyobi denryoku fuka heijunka taio

Energy Technology Data Exchange (ETDEWEB)

Kikuchi, R.; Essaki, K.; Tsutsumi, A. [The University of Tokyo, Tokyo (Japan). Dept. of Chemical System Engineering; Kaganoi, S.; Kurimura, H. [Teikoku Sekiyu Co., Tokyo (Japan); Sasaki, T.; Ogawa, T. [Toshiba Co., Tokyo (Japan)

2000-03-10

Thermochemical recuperative combined cycles with methane-steam reforming are proposed for improving their thermal efficiency and for peak-load leveling. For targeting higher thermal efficiency, a cycle with methane-steam reforming reaction heated by gas turbine exhaust was analyzed. The inlet temperature of gas turbine was set at 1,350 degree C. Low-pressure steam extracted from a steam turbine is mixed with methane, and then this mixture is heated by part of the gas turbine exhaust to promote a reforming reaction. The rest of the exhaust heat is used to produce steam, which drives steam turbines to generate electricity. The effect of steam-to-methane ratio (S/C) on thermal efficiency of the cycle, as well as on methane conversion, is investigated by using the ASPEN Plus process simulator. The methane feed rate was fixed at constant and S/C ratio was varied from 2.25 to 4.75. Methane conversion shows an increasing trend toward the ratio and has a maximum value of 17.9 % at S/C=4.0. Thermal efficiency for the system is about 51 % higher than that calculated for a conventional 1,300 degree C class combined cycle under similar conditions. A thermochemical recuperative combined cycle is designed for peak-load leveling. In night-time operation from 20 : 00 to 8 : 00 it stores hydrogen produced by methane steam reforming at S/C=3.9 to save power generation. The gas turbine inlet temperature is 1,330 degree C. In daytime operation from 8 : 00 to 20 : 00 the chemically recuperated combined cycle operated at S/C=2.0 is driven by the mixture of a combined cycle operated at constant load with the same methane feed rate, whereas daytime operation generated power 1.26 times larger than that of the combined cycle. (author)

Results of photovoltaic power generation system operation in Tokyo Electric Power Company; Tokyo Denryoku ni okeru taiyoko hatsuden setsubi no unten jisseki ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Fukuda, H; Itokawa, K [Tokyo Electric Power Co. Inc., Tokyo (Japan)

1996-10-27

A report was made on the measurement of data and the results of the analysis at 14 sites of photovoltaic power generation facilities operated under system interconnection by Tokyo Electric Power Company. This type of system is provided in 40 sites as of the end of fiscal 1995, generating 479kw. The items measured were the generated electric energy at all 14 sites, and the quantity of solar radiation, outside air temperature, panel temperature, etc., at limited sites; and the capacity of each equipment, azimuth and inclination of the panel were also recorded simultaneously. Hourly values were used for the analysis. Five minute values were utilized, however, in the examination of the cause of lowered output and in the situation recognition of the influence of the shade or the change of weather. The utilization factor of the facilities was in the average 10.8% in fiscal 1994 and 10.7% in fiscal 1995. The factor decreased slightly unless the panel azimuth faced due south. The utilization factor at the panel inclination of 35 degrees and 45 degrees showed both 10.4% through the year making no difference. The system seemed to show no overwhelming possibilities in coping with electric power demand. The reason was that deviation existed for 2 hours or so in the peak and that reliability was low as basic power facilities. However, it was determined that the system be continuously examined in future. 9 figs., 1 tab.

Preparation of meteorological data (METPV) which is useful to simulate output from PV systems; Taiyoko hatsuden system no simulation yo data METPV no seibi

Energy Technology Data Exchange (ETDEWEB)

Itagaki, A; Iida, H [Japan Weather Association, Tokyo (Japan)

1996-10-27

Studies are under way for the nation-wide buildup of a network of METPV data, new standard meteorological data resembling the HASP data, for the time-based simulation of the output of photovoltaic power generation systems. There is a method of preparing hourly data covering a long period of time for computer processing for the determination of the average hourly power generation level, which, however, will be unrealistic because of the enormity of calculation work involved. Hence: the concept of standardized meteorological data, which involves the specification of typical years after examining the data covering a long period and the preparation of the data of the years for computer processing. In the METPV setup, three types of data are prepared: data for the year of the average insolation, data for the year of insufficient insolation, and data for the year of excess insolation. Next, for each of the twelve months, the year of the average insolation is found. When the twelve pieces of data for the twelve months (of different years) are combined, an artificially constructed year results, with each of the twelve months having the average insolation. A technique has been developed for smoothing the discontinuity between the months. Forty observation spots were built in fiscal 1995, and 150 spots will have been prepared across the country by the end of fiscal 1996. 6 refs., 4 figs.

Fiscal 1993 investigational study of a model of international cooperation for an environmentally harmony type green technosystem; 1993 nendo Oshu ni okeru haikibutsu shori oyobi recycle no doko ni kansuru chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

For the natural environment preservation, effective utilization of resources, and maintenance of the ecosystem, an international cooperation model was proposed for the environmental harmony type green technosystem. A comprehensive evaluating analysis of a green forest resource, etc. as the global resource, and an intensive extraction of subjects and needs was made. The analysis was conducted of technical possibility and abstract business development effects toward the industrialization with high values added which is in harmony with the environment. As a case study, the Papua New Guinea area, Malaysia was selected and re-evaluated. For this typical tropical forest area, a new technical system was studied based on the natural environment, industry/economy, social/cultural assessment, etc., and a model for industrializing new international cooperation was proposed. For the model making for industrialization, various steps to be taken and conditions to be prepared were studied and arranged for the realization. Upon going ahead with the international technical cooperation, Japan, a large lumber consuming country, needs to always consider the fostering and effective use of lumber resource in particular. 27 refs., 28 figs., 30 tabs.

Report on results 1998. Research and development on high-temperature superconducting flywheel power storage (investigation on system introduction); 1998 nendo seika hokokusho. Koon chodendo flywheel denryoku chozo kenkyu kaihatsu (system donyu chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

In introducing high-temperature superconducting flywheel power storage equipment to an electrical power system, adaptability is examined and evaluated concerning secondary effect that can be expected while a load leveling function is maintained. The 1998 plan is such that the functions and usages other than the load leveling are put in order for such equipment, and that the effect/adaptability in the case of the introduction into the power system is evaluated by means of simulation and literature studies. The high-temperature superconducting flywheel power storage equipment may be used for such purposes as energy adjustment for a short time, system voltage adjustment and emergency power source, other than the load leveling, on the basis of the characteristics that enable high speed control of active/reactive power and storage/release of energy. Enumerated, as the effects obtainable in introducing these uses into the power system, are enhancement in system stability, improvement in voltage stability, improvement in instantaneous voltage drop, maintenance of system frequency, compensation of fluctuating load, countermeasures against power outrage, and output leveling of intermittent power sources, and these effects were examined. (NEDO)

Report on survey in fiscal 2000. Survey on introduction of external accreditation system in engineer education (civil engineering); 2000 nendo chosa hokokusho. Gijutsusha kyoiku no gaibu ninteiseido donyu ni kansuru chosa (Doboku)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In order to ensure international applicability of engineer education such as in universities and other organizations, and to improve the environment to supply human resources demanded by economic societies, surveys and discussions were given on the external accreditation system for engineer education such as in universities and other organizations. In the field of civil engineering, a special sub-committee was organized, and in advance to a trial examination, surveys and discussions were executed by participating in the actual examination of the engineer educational program at the engineering department of Auckland University, and by participating in the ABET trial examination by the civil engineering department of Kansas State University and the engineering department of Stanford University in the U.S.A. The trial examination was performed upon selecting the engineer educational programs of the civil engineering department of Kinki University and Tottori University. This paper describes the fundamental policies on the educational program examination work for the field of civil engineering, the self-assessment under the educational program, the direction of engineering qualification and educational accreditation, the fundamental concept of examination and accreditation and evaluation process, the works done by the civil engineering section of the science and engineering department of Kinki University, and the works done by the civil engineering section of the engineering department of Tottori University. (NEDO)

FY 2001 report on the results of the trend survey of introduction of clean energy vehicle for the transport industry; 2001 nendo unso yo clean energy jidosha no donyu doko chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

Survey/analysis were made on the details of the plan on the leading introduction of clean energy vehicle by 632 transporters who applied for the project on promotion of clean energy vehicle in FY 2001. As a result of the survey, the following were made clear. The clean energy vehicles to be planned to be introduced by transporters are all natural gas vehicles. The transporters planning the leading introduction are mostly in large cities and are spreading also in the periphery. Fifty three percent of the transporters predicts that the predicted average running distance of the clean energy vehicle to be introduced is the same as those of the vehicles they owns, and 39% predicts that it is shorter. About the form of utilization, they use it overwhelmingly for the regional collection/delivery. It is considered that the improvement in running distance per 1 fuel filling of clean energy vehicle will contribute to the spread. Fuel supply stations that the clean energy cars to be introduced use concentrate in the good location. It is necessary to strongly promote preparation of the infrastructure. (NEDO)

Development of hot water utilizing power plants in fiscal 1999. Development of binary cycle power plant (Development of system to detect well bottom information when geothermal hot water is excavated); 1999 nendo nessui riyo hatsuden plant nado kaihatsu seika hokokusho. Binary cycle hatsuden plant no kaihatsu (chinetsusei kussakuji kotei joho kenchi system no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Developmental research has been performed on the MWD system to identify on the real time basis the information about well bottom when geothermal hot water is excavated (azimuth, inclination, pressure and temperature). This paper summarizes the achievements in fiscal 1999. In the developmental research on the detection device, attempts were made in improving the zonde, and enhancing its heat resisting performance. In addition, data were acquired on electronics parts as a result of the heat resistance identifying test. For the on-the-ground devices, improvement was made to add the experiment analyzing program with a program to remove the downhole motor pressure noise. The pressure noise during excavation in the actual wells was collected. In the analyzing system, use of PC, improvement, and operation check were performed on the well trace projecting and indicating system. Operation of the well trace estimating system was checked by using the actual data in order to prepare the operation manual. With regard to the well evaluation supporting system, improvement, operation check and that by using the actual data were executed on the PC version temperature analyzing system. Performance of the zonde was verified by the actual geothermal well test. (NEDO)

FY 2000 report on the results of the development of commercialization technology of the photovoltaic power system. Demonstrative study of the photovoltaic power system (Study of the high density connection technology); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Taiyoko hatsuden system no jissho kenkyu (Komitsudo renkei gijutsu no kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the photovoltaic power system connected to the distribution line in high density, study was made in terms of the power quality, elucidation of the effect on operation/protection of the distribution line and the measures to be taken, improvement of power quality using inverter, etc., and the FY 2000 results were summed up. In this fiscal year, the results of the research made in four years were arranged, and at the same time, the theoretical analysis, verification test, etc. that were necessary for summarization of the research results were carried out. As to various kinds of technology for the measures to be taken, the following were conducted: study of the effect on the rise in voltage of the distribution line, development of the dispersed control type voltage stabilization method, test on characteristics of individual operation of the inverter on the market, simulation analysis of characteristics of the continuous individual operation, development of the high reliability individual operation prevention method, verification study of the environmental adaptability, etc. As a technology for improving utility value of the photovoltaic power generation, a high function inverter was developed which conducts not only the dc-ac conversion, but the smoothing of generating output/load variations and load higher harmonics/reactive power compensation. At the Rokko testing facilities, test was made of the parallel operation (5 units) of the pole transformer. (NEDO)

Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Research and development of photovoltaic power generation system evaluation technology (Research and development of system evaluation technology); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu (system hyoka gijutsu no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Research and development is conducted for the acquisition of a system evaluation technique for predicting the performance of standard photovoltaic power systems and evaluation technologies applicable to residential photovoltaic power systems different from each other in terms of tilt and direction, district, solar cell type, etc. In fiscal 1999, using data collected from the Hamamatsu field test facilities and residential photovoltaic power systems installed across Japan, various design parameters, such as the irregularity compensation coefficient, temperature compensation coefficient, and the incidence compensation coefficient were determined, and, using the parameters as the secondary estimation values, design parameters were updated. In the development of simulation technologies, basic studies were made about the shadow compensation coefficient, spectral response fluctuation compensation coefficient, and the composition of polyhedral arrays. Moreover, studies were made about the estimation of large area insolation, based on the horizontal surface insolation data collected at 21 sites of residential photovoltaic power systems in the Kanto district. (NEDO)

Report on achievement in developing fuel cell power generation technology in fiscal 1998. Research and development of molten carbonate fuel cell power generation system (Test of the research result report); 1998 nendo nenryo denchi hatsuden gijutsu kaihatsu seika hokokusho. Yoyu tansan'engata nenryo denchi hatsuden system no kenkyu kaihatsu (kenkyu seika no honbun)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

This paper summarizes the text of the research result report in the separate volume II-1 from among the fiscal 1998 report on the achievement made on researching and developing a molten carbonate fuel cell (MCFC) power generation system. For the AC-DC type system whose high performance and large capacity stacks are being developed, detail designs were made on 250-kW class stack module assembly and installation procedure. At the same time, processing and forming were continued on such main components as electrodes, electrolyte plates and separators. The cells were assembled as modules, sintered, installed and adjusted. Aids were given by the process and control (PAC) test on devices and piping of the fuel cell system block. Cell life extension is also under study. For the parallel flow type stack, two 250-kW stacks were fabricated, and an overall adjustment test was begun thereon in March. For the reformer, an internal reforming system was developed for the 200-kW class system, whose adjustment test is scheduled for April 1999. Capacity increase is also under discussion. For practical use of MCFC, stack life of 40,000 hours is said required. The current status is at the level of exceeding 10,000 hours, but the necessity is seen in suppressing voltage drop associated with lapse of time. (NEDO)

FY 2000 report on the results of the development of commercialization technology of the photovoltaic power system. International cooperation project (Collection of the information on the IEA photovoltaic power generation program); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu kokusai jigyo kyoryoku (IEA taiyoko hatsuden program ni kansuru joho shushu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Based on 'the Implementing agreement for a research cooperation project on the photovoltaic power system' being promoted by IEA, collection of the information on the photovoltaic power system was made, and the FY 2000 results were summarized. In Task I: Exchange of the information on the photovoltaic power system and the spread, the final report on 'the study on added values of PV system' was made. In Task II: Operational performance and design of the photovoltaic power system and subsystem, specifications for new database were determined, and the existing data were checked/revised/added. In Task III: Design and operation of the stand-alone type and remote island use photovoltaic power plant, survey was conducted of the present situation of technical standards and quality guarantee. In Task 7: Photovoltaic power system integrated with construction materials, work was done for making a book of installation samples of the PV system integrated with construction materials in each country. In Task 8: Investigative study of possibilities of the large-scale photovoltaic power generation using the unused land such as desert, a report making of the secondary survey was started. (NEDO)

FY 2000 report on the results of the development of commercialization technology of the photovoltaic power system. International cooperation project (Collection of the information on the IEA photovoltaic power generation program); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu kokusai jigyo kyoryoku (IEA taiyoko hatsuden program ni kansuru joho shushu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Based on 'the Implementing agreement for a research cooperation project on the photovoltaic power system' being promoted by IEA, collection of the information on the photovoltaic power system was made, and the FY 2000 results were summarized. In Task I: Exchange of the information on the photovoltaic power system and the spread, the final report on 'the study on added values of PV system' was made. In Task II: Operational performance and design of the photovoltaic power system and subsystem, specifications for new database were determined, and the existing data were checked/revised/added. In Task III: Design and operation of the stand-alone type and remote island use photovoltaic power plant, survey was conducted of the present situation of technical standards and quality guarantee. In Task 7: Photovoltaic power system integrated with construction materials, work was done for making a book of installation samples of the PV system integrated with construction materials in each country. In Task 8: Investigative study of possibilities of the large-scale photovoltaic power generation using the unused land such as desert, a report making of the secondary survey was started. (NEDO)

Report on achievements in fiscal 1999 of energy and environment technology verification project formation assisting project and international joint verification and research project. Verification of discrete power generation system utilizing mini-power generation that utilizes micro gas turbine; 1999 nendo micro gas turbine riyo mini hatsuden wo riyoshita bunsangata hatsuden system no kensho seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This paper describes the verification test on power generation by using natural gas driven micro gas turbines (rated at 28 kW) in Thailand. The turbine presented excellent result of providing a maximum power generation output of 25 kW, having no efficiency deterioration even at the 50% output point (about 22%). Its exhaust gas emitted under the normal operation is clean. The waste heat is as low as 290 degrees C, which can be used for hot water supply, but may be difficult for steam generation. Under the severe condition for building large power plants in remote areas due to environmental issues and power transmission loss, proliferation of the discrete power generation system in the suburbs of the city of Bangkok draws expectation. This system can be more advantageous than the existing facilities if the end user gas price is 6.7 Bht/m{sup 3} or less. Discussions were given on a hybrid electric vehicle (HEV) bus driven by electric power generated from the gas turbine mounted on the bus. The bus is overwhelmingly superior in the environmental aspect to diesel fueled buses. The HEV bus emits no black smoke at all, and NOx emission is as low as about 1/70. Fuel consumption is less than half (when regenerative braking is used). However, the vehicle body cost is higher by 40%. Smooth operation of the buses requires indispensably deployment of compressed natural gas service stations (to be located at 40-km interval ideally). Assistance is required also on the fund for gas line installations, and civil engineering construction technologies. (NEDO)

Report on evaluation concerning R and D of magneto hydrodynamic (MHD) generation. Introduction; Denji ryutai (MHD) hatsuden no kenkyu kaihatsu ni kansuru hyoka hokokusho. Soron

Energy Technology Data Exchange (ETDEWEB)

NONE

1984-03-01

Evaluation was conducted concerning R and D on magneto hydrodynamic (MHD) generation, with proposals made for the future R and D. As a result of the experimental operation and studies of the Mark 7 machine for MHD generation, a cold wall type generation channel was found promising in the long-term durability under MHD generation conditions. In addition, R and D was conducted on the exhaust gas control system that fulfilled an environmental standard, seed recovery method, grasp of seed coagulation state, etc. The R and D on element technologies were carried out along with the R and D of the Mark 7 and played a role in the backup of its experiment. MHD generation presents a large number of attractive characteristics, with its development expected in the future. However, it seems too early to immediately move on to the next step. Examinations should be made on such matters as comparisons with various kinds of new power generation systems using coal, trends in foreign countries particularly the U-500 project of the Soviet Union, the ideal system for more efficient development, and possibility of international cooperation. (NEDO)

Fiscal 1974 Sunshine Project result report. Research on solar energy utilization systems (photovoltaic power generation); Taiyo energy riyo system chosa kenkyu seika hokokusho. Taiyoko hatsuden

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-03-01

This report summarizes the research result on the guide for developing solar cells. The report includes (1) standard measurement method for solar cells, (2) system configuration and installation site, (3) optimum design and profitability of solar cells and (4) raw materials and pollution prevention. In the 1st research, study was made on the standard for solar radiation intensity, the definition and measurement methods for spectral profiles, and the measurement conditions for solar cells. In the 2nd research, study was made on various basic data for the scale of photovoltaic power systems. In the 3rd research, since it is necessary to obtain characteristics of solar cells with any profiles of physical constants such as impurity, minority carrier life and mobility by simulation of solar cell actions, research was made on the measurement method of minority carrier lives by using a prepared computer program. Technical and economical comparisons were also made between Si solar cells with various structures. In the 4th research, survey was made on various data for compound semiconductors, and study was made on industrial waste pollution. (NEDO)

Output characteristics of 40 kW photovoltaic power generation system in ICT; Ibaraki kosen ni okeru 40 kW taiyoko hatsuden shisutemu no shutsuryoku tokusei

Energy Technology Data Exchange (ETDEWEB)

Sekiguchi, N. [Ibaraki National College of Tech., Ibaraki (Japan); Tani, T. [Science University of Tokyo, Tokyo (Japan)

1999-11-25

The photovoltaic power generation system consists of photovoltaic array and power conditioner of the utility connected system. The photovoltaic array parallelly constitutes 18 serial 30 of the modules of 540 sheets, and there is the generating capacity of largest 40 kW. The power conditioner uses 10 kW four units, and it is tracking with function of the maximum output point. This report examined the unconformable rate of photovoltaic array maximum output operating voltage, current and power in simulation and power conditioner input. (author)

FY 1998 annual report on power generation by waste heat from cement production in China; Chugoku ni okeru cement hainetsu hatsuden 1998 nendo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This project is to implement a feasibility study for applying waste heat power generation, which have been already commercialized in Japan and producing remarkable results, to China's cement plants producing 3,500 t/d or more of clinker, and thereby to try to establish a link with the Japan's clean development mechanism. It is expected that introduction of these systems improves energy use efficiency and environments in China. The study results indicate that the project for a Tongling Conch plant could generate power of 15,000 kW, reducing CO2 emissions by 89,178 t/y and cumulatively 1,783,560 tons in the 20-year period. The results also indicate that the project will be highly profitable, with an estimated internal return rate of as high as 33.78%. The project for a Huaxin plant could generate power of 8,400 kW, reducing CO2 emissions by 48,412 t/y and cumulatively 968,240 tons in the 20-year period, annually saving power charges by 325 million yen and bringing an internal return rate of 10.72%. (NEDO)

PW-6ES gas turbine generator for Maglev linear motor car. Yamanashi rinia jikkensen daiichi hensei sharyo tosaiyo PW-6ES gas tabin hatsuden sochi

Energy Technology Data Exchange (ETDEWEB)

Yamamoto, T [JR Railway Technical Research Inst., Tokyo (Japan); Nakamura, S [Ebara Corp., Tokyo (Japan)

1994-06-10

A power generator is developed to be used as the auxiliary power source for the first carriage at the levitation type railway Yamanashi linear experimental line. The gas turbine generator is installed to supply power to the electric equipment on the carriage, and the power generating conditions are transmitted to the ground commanding room via on-board central control system for centralized controlling. An aircraft diversion type ST6 gas turbine and a high frequency light weight generator are combined for the gas turbine generator developed this time. Single reduction planetary gear is employed for the reduction gear which connects the two units directly, the gas turbine being connected to one side and the generator to the other side with no coupling. The output of the generator is 350kW, AC 455V, and 400Hz, and power is supplied to the electric devices on the carriage after having been converted to DC 600V. Aluminium is used to reduce the weights of the soundproof enclosure and exhaust dust shell plate. 1 fig., 1 tab.

Data book on new energy technology development in FY 1997. Photovoltaic (PV) power generation; Shin energy gijutsu kaihatsu kankei data shu sakusei chosa. Taiyoko hatsuden

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

For the purpose of understanding the present status of photovoltaic power system (PVPS) and supporting its promotion, various data were collected. The significance of adopting PV power technology was specified for customers of various levels, such as nation, local communities, industries and individual households, to clarify the CO2 reduction effect and energy pay-back time. Data illustrate the solar cell production according to region, cell types, industries, applications, production value, and market price. Policies for PVPS in industrial countries were compared with those in Japan. Distribution of PVPS in various countries was compared with that in Japan in respect to installations and purposes of the introduction of PVPS. Financial aid programs such as subsidies, tax benefits and loans for the installation of PVPS in Japan were listed. The trend of PV-related budget of MITI was shown with every project`s description. Steps of introducing PVPS from plan to installation were depicted in the form of flow chart. Were shown measures sponsored by the government or local organizations to promote PVPS. Domestic and foreign firms related to PVPS including PV module suppliers, and PV installation contractors were listed

Survey on the technological development issues for large-scale methanol engine power generation plant; Ogata methanol engine hatsuden plant ni kansuru gijutsu kaihatsu kadai chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

Based on the result of `Survey on the feasibility of large-scale methanol engine power generation plant` in fiscal 1992, concrete technological development issues were studied for its practical use, and the technological R & D scheme was prepared for large-scale methanol engine power plant featured by low NOx and high efficiency. Technological development issues of this plant were as follows: improvement of thermal efficiency, reduction of NOx emission, improvement of the reliability and durability of ignition and fuel injection systems, and reduction of vibration. As the economical effect of the technological development, the profitability of NOx control measures was compared between this methanol engine and conventional heavy oil diesel engines or gas engines. As a result, this engine was more economical than conventional engines. It was suggested that development of the equipment will be completed in nearly 4 years through every component study, single-cylinder model experiment and real engine test. 21 refs., 43 figs., 19 tabs.

FY 2000 report on the survey of the stabilization of wind power generation power system, etc.; 2000 nendo furyoku hatsuden denryoku keito anteika nado chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of elucidating effects of output fluctuations at the time of quantity introduction of wind power generation, conducted were observation of wind characteristics in Hokkaido and analysis of the characteristics, estimation of fluctuations in wind power output, analysis of fluctuations in system frequency, etc. In the observation of wind characteristics, wind velocity/wind direction were measured at observation posts of 30 wind turbines installed at 16 sites in Hokkaido. Concerning the conversion into wind power output, 10 cases were selected such as the case of passage of low atmospheric pressure, etc., and the generator unit and wind firm were simulated in detail. In the estimation of wind power output, good agreement with the results estimated was confirmed at points very near to posts of observation of wind characteristics. As to the evaluation of effects of wind power generation to the system, power system frequencies were simulated using the models constructed and using capacity and kinds of frequency adjusted power source as parameter. As a result, it was indicated that there was a possibility of frequency's sharply fluctuating in case the surplus energy in frequency adjustment is reduced by fluctuations in demand and further in case wind power output is fluctuated. (NEDO)

Study of highly efficient power generation system based on chemical-looping combustion; Chemical loop nenshoho ni yoru kokoritsu hatsuden system no kaihatsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Ishida, S; Suzuki, T; Yamamoto, M [Tokyo Institute of Technology, Tokyo (Japan). Research Laboratory of Resources Utilization

1997-02-01

This paper describes the research and development of power generation system by means of chemical-looping combustion. For this system, fuel flows in a reduction reactor and air flows in an oxidation reactor. These two flows are separated. As a result, recovery of CO2 without energy consumption, drastic improvement of power generation efficiency, and suppression of NOx emission are expected. To realize the above, two promising candidates, NiCoO2/YSZ and NiO2/NiAl2O4, have been found as recycle solid particles between the both reactors. These have excellent oxidation/reduction cycle characteristics. By these particles as well as the existing particle, NiO/YSZ, practical application of the chemical-looping combustion is realized. Besides LNG, coal and hydrogen were considered as fuels. When using coal or hydrogen, it was found that temperature of the reduction reactor should be increased the same as that of the oxidation reactor. This is a different point from a case using LNG as a fuel. 5 refs., 2 figs.

Development of hydroponic system using agricultural waste. 2. Utilization of ozone for sterilization of nutrient solution; Suiko saibai ni okeru haikibutsu riyo gijutsu no kaihatsu. 2. Ozone ni yoru baiyoeki sakkin ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Terazoe, H; Yoshihara, T; Nakaya, K [Central Research Institute of Electric Power Industry, Tokyo (Japan)

1995-08-01

Discussions were given on a sterilizing effect of ozone on Fusarium bacteria in hydroponic culture, and its effect on components in the culture solution. In an experiment, dry air with O3 concentration of 3.5 ppm was sent into aqueous solution inoculated with Fusarium bacteria at a flow rate of 5 liters per minute. The Fusarium bacteria was sterilized nearly completely in about five minutes. No change was observed in pH, EC and dissolved oxygen concentration of the O3-treated culture solution. However, iron and manganese among the soluble components have been oxidized by O3 and precipitated, hence these components must be added after the O3 treatment. In spinach culture performed on a culture medium inoculated with Fusarium bacteria, ozone water containing dissolved O3 at 0.8 ppm was flown into a urethane foam medium and vegetable roots. This treatment has resulted in reduction of the number of strains occurred with a wilt symptom below that in the section flown with distilled water. The spinach has grown normally without showing an effect of the ozone water. 15 refs., 10 figs., 3 tabs.

Technological development report for fiscal 1993 on the woodwaste thermolysis/gasification technology and generated gas utilization technology; 1993 nendo mokushitsukei haikibutsu no netsubunkai gas ka gijutsu to seisei gas no riyo gijutsu kaihatsu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

The project is a joint effort of Japan and the Philippines to develop a thermolysis/gasification system, in which woodwaste now remaining unexploited in the Philippines is subjected to thermolysis/gasification and the resulting gas is used in a gas engine for the generation of electric power, in a 5-year period beginning in fiscal 1990. In this fiscal year, element technology verification tests are conducted, components of a demonstration plant are manufactured, and procurement is made as required, which completes all the tasks allotted to this fiscal year. All the constituents of the said demonstration plant fabricated or procured since fiscal 1991 are packed up and forwarded to Industrial Technology Development Institute (ITDI) of the Philippines, and engineering guidance is extended and test operations are carried out at the site of plant installation. In line with the said endeavors, on-site investigations are performed and researches are conducted together with ITDI scientists concerning the construction work and element technology confirmation. On the other hand, the Philippine side performs the second phase of civil engineering and construction carried over from the first phase. The demonstration plant is completed, adjustment and test operations are carried out, which means that the project is in progress as initially scheduled. (NEDO)

FY 2000 report on the survey of the project to promote and support the formation of the environmentally friendly energy community. Study of the industrialization of the gasification power generation business by the pressurized two-stage gasification process using organic waste such as waste plastic as raw materials; 2000 nendo kankyo chowagata energy community keisei sokushin hojo jigyo chosa hokokusho. Kaatsu nidan gas ka process ni yoru hai plastic nado yuki haikibutsu wo genryo to suru gas ka hatsuden jigyo no jigyoka kento

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Viability was studied of the power generation business using plastic waste as fuel and the methanol production business. In the project, the container packing waste plastic which was sorted/collected is supplied by tender, and the organic waste such as shredder dust is mixed. And the electric power is supplied to the gasification power generation facilities by the pressurized two-stage gasification process, neighboring plants, etc. As an alternative, the methanol production was also studied. As a result of the study, if the total amount of the waste plastic needed at the supply price assumed at present can be supplied, the business can be viable economically even without subsidy, but if the supply risk in supposing tender is considered, a subsidy of approximately 10% of the equipment/plant investment is needed. As to the methanol production as an alternative, it was indicated that the economical efficiency is almost the same, but the profitability gets fast worse due to the waste plastic supply cost since there is not much income and expenses are high despite of the smaller investment size than that in the case of the power generation. (NEDO)

Effect of heat-insulating wall on input energy of a photovoltaic/solar/air-heat system for a residence; Jutaku no kodannetsuka ni yoru taiyoko netsu/taiki netsu system no donyu energy sakugen koka

Energy Technology Data Exchange (ETDEWEB)

Kenmoku, Y; Sakakibara, T [Toyohashi University of Technology, Aichi (Japan); Nakagawa, S [Maizuru College of Technology, Kyoto (Japan)

1996-10-27

A proposal was made to introduce a photovoltaic/solar/air-heat system which positively utilizes natural energy in order to curtail consumption of fossil energy, corroborating that the system has greatly reduced energy input in the primary energy level in a house. This paper examines the effect of curtailment of energy input in the case of reducing the load of air conditioning through the high heat insulation of a house. The energy input was evaluated by calculating additional equipment energy needed newly for the high heat insulation. The system performance and the energy load varied greatly depending on weather conditions. The subject system consisted of solar cells, inverter, heat concentrator, heat storage tank, heat pump and gas hot-water supply device. The thickening of the insulation sharply reduced heating load in the house, thereby decreasing fuel energy substantially. An insulation material of 100mm thick was capable of reducing energy input by 16-23% compared with that of 50mm thick. 5 refs., 5 figs, 3 tabs.

Fiscal 1999 geothermal energy development promotion survey. Report on survey of introduction of techniques for predicting impact on hot springs; 1999 nendo chinetsu kaihatsu sokushin chosa hokokusho. Onsen eikyo yosoku shuho donyu chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-08-01

In an effort to find guidelines on how to proceed with geothermal energy development so that it may coexist with hot springs, investigations are conducted into cases of impacts on hot springs imposed by geothermal energy development activities. An impact is judged to exist when geothermal development results in a decrease or depletion of pumped or spontaneously welling hot spring water, change in the concentration of dissolved chemical ingredients, fall in water temperature, or in an increase in the amount of discharged steam. Keyword-aided retrieval of data from databases is performed, and geothermal magazines are referred to for information. There are articles reporting impacts imposed by geothermal development on hot springs in the Palinpinon area (Philippines) and 12 others and in the Corwin Springs area (U.S.) and 13 others. These articles carrying outlines and impacts of geothermal development are collected, put in order, and analyzed. Cases in which such impacts are found to exist are categorized into four groups and, in each group, episodes are differentiated from each other by the type of mechanism linking the aquifer and the reservoir which is the object of development. (NEDO)

Fiscal 1980 Sunshine Project research report. Development of hydrothermal power plant. Development of binary cycle power plant (Research on heat cycle, heat medium, material and heat medium turbine); 1980 nendo nessui riyo hatsuden plant no kaihatsu seika hokokusho. Binary cycle hatsuden plant no kaihatsu (netsu cycle oyobi netsubaitai no kenkyu, zairyo no kenkyu narabini netsubaitai turbine no kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

This report summarizes the fiscal 1980 research result on each element of the next 10MW class geothermal binary cycle power plant, following last year. In the research on heat cycle and heat medium, measurement was made on the liquid density, vapor density, liquid specific heat, vapor specific heat and thermal conductivity of 8 heat media to prepare the precise pressure enthalpy chart. The thermal stability of each medium was also measured under a flow condition. The heat cycle of each medium was calculated in a hydrothermal temperature range of 120-160 degrees C for evaluation of its output. In the research on material, field corrosion test and laboratory simulation were made on 3 kinds of heat exchanger martials for acidic hot water to study the corrosion behavior of welding members. In the research on heat medium turbine, study was made on sealing characteristics such as differential pressure, flow rate and friction of sealing oil for oil film seal and mechanical seal as shaft seal devices of heat medium turbines for the 10MW class geothermal plant. (NEDO)

FY 1991 report on the results of the development of an entrained bed coal gasification power plant. Part 1. Support study for the development of an entrained bed coal gasification power plant (Dismantling study); 1991 nendo seika hokokusho. Funryusho sekitan gaska hatsuden plant kaihatsu (Funryusho sekitan gaska hatsuden plant kaihatsu no shien kenkyu) - Sono 1. Kaitai kenkyu hen

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-04-01

As a support study for the development of an entrained bed coal gasification power plant by a 200 t/d pilot plant, the dismantling study was made for gasifier facilities, desulfurization facilities, dedusting facilities at the existing 40 t/d testing facilities. In the results of the analysis of the specimens sampled from gasifier and peripheral facilities, the corrosion loss of thickness was great in carbon steel/low-alloy steel equipment, and the generation of intergranular corrosion/intergranular crack was recognized in stainless steel equipment. The loss of thickness caused by erosion was also recognized in carrier tubes, etc. As to the high-temperature dry desulfurization system, the damage was totally great, but the effect of taking measures for it was unclear because the loss of thickness by corrosion/abrasion had not been measured regularly. Relating to the high-temperature dry dedusting system, there used to be a lot of troubles from stress corrosion cracking and pitting corrosion, and the best measures for corrosion prevention were taken for each trouble. As to the Al thermal spraying, stabilized thermal treatment, shot-peening, etc., the excellent corrosion prevention effect was recognized on the austenite stainless steel. (NEDO)

FY 2000 report on the results of the development of commercialization technology of the photovoltaic power system. International cooperation project (IEA photovoltaic power generation program - Collection of the information on Task IX); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu kokusai jigyo kyoryoku (IEA taiyoko hatsuden program task IX ni kansuru joho shushu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Based on 'the Implementing agreement for a research cooperation project on the photovoltaic power system' being promoted by IEA, collection of the information was made on Task IX: Promotion of the effective spread of the PV technology in developing countries, and the FY 2000 results were summarized. In Task IX, for technical/economic subjects in introducing the PV system to developing countries, a commendable/practical guide using the experiences having been gained was to be arranged. Also, workshop was to be opened in developing countries as model, and cooperation was to be promoted with international organizations such as the Bank of the World. In this fiscal year, two meetings of specialists (abroad) and four sectional meetings of operation (in Japan) were held. This fiscal year was the second year of the 5-year plan. The standard for selecting developing countries as model was studied, and a draft of the commendable/practical guide was made and discussed in the meeting of specialists. (NEDO)

Fiscal 1981 Sunshine Project research report. Development of hydrothermal power plant. Development of binary cycle power plant (Research on heat cycle and heat medium, materials, and heat medium turbine); 1981 nendo nessui riyo hatsuden plant no kaihatsu seika hokokusho. Binary cycle hatsuden plant no kaihatsu (netsu cycle oyobi netsubaitai no kenkyu, zairyo no kenkyu narasbini netsubaitai turbine no kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

This report summarizes the final fiscal 1981 research result on components of the next 10MW class geothermal binary cycle power plant. In the research on heat cycle and heat medium, R-C318 and R-124 were excellent in output characteristics in a low-temperature zone and high-temperature zone in a hot water temperature range of 120-160 degreesC, respectively, however, at present R-114 was most reasonable from the viewpoint of heat medium price and supply system. In the research on martials, study was made on inlet-attack and stress corrosion of heat exchanger pipes of 18Cr-13Ni-2Mo steel, and combination use of inexpensive materials (carbon steel). As used giving attention to stress corrosion, at present 18Cr-13Ni-2Mo steel was most suitable material, while clad carbon steel was also usable. In the research on heat medium turbine, the 1000-hour durability test result of mechanical seal showed that mechanical seal is best for heat medium turbines. (NEDO)

New Sunshine Program for Fiscal 2000. International cooperative project for developing photovoltaic power system practicalization technology (International Energy Agency (IEA)/Cooperative Program on Photovoltaic Power Systems (PVPS) implementing agreement - Executive committee meeting); 2000 nendo New sunshine keikaku. Taiyoko hatsuden system jitsuyoka gijustu kaihatsu kokusai kyoryoku jigyo (IEA taiyoko hatsuden system kenkyu kyoryoku program jisshi kyotei shikko iinkai)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Cooperative endeavors of research and development, verification, analysis, information exchange, introduction acceleration, etc., were exerted through participation in the above-said PVPS program. At the 15th PVPS executive committee meeting held in this fiscal year, reconsideration was made about the commencement of new tasks, change of OAs (operating agents), change of participating countries, etc., whose current state was not correctly reflected in the existing implementation agreement. At the 16th PVPS executive committee meeting, discussions were made and conclusions were reached that the next executive committee meeting decide whether to change the chairman, that deliberation be made in 2003 to decide whether to hold the 4th IEA/PVPS executive conference in Japan, that the assessment of each of the tasks be carried out in fiscal 2001, and that Task I conduct studies about market implementation for the fruits of the research-centered activities in the past to hit the market, etc. Workshop meetings were held, where Australia, France, Italy, and Japan reported their PVPS research, development, and popularization efforts. (NEDO)

FY 2000 report on the results of the development of commercialization technology of the photovoltaic power system. International cooperation project (IEA photovoltaic power generation program - Collection of the information on Task IX); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu kokusai jigyo kyoryoku (IEA taiyoko hatsuden program task IX ni kansuru joho shushu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Based on 'the Implementing agreement for a research cooperation project on the photovoltaic power system' being promoted by IEA, collection of the information was made on Task IX: Promotion of the effective spread of the PV technology in developing countries, and the FY 2000 results were summarized. In Task IX, for technical/economic subjects in introducing the PV system to developing countries, a commendable/practical guide using the experiences having been gained was to be arranged. Also, workshop was to be opened in developing countries as model, and cooperation was to be promoted with international organizations such as the Bank of the World. In this fiscal year, two meetings of specialists (abroad) and four sectional meetings of operation (in Japan) were held. This fiscal year was the second year of the 5-year plan. The standard for selecting developing countries as model was studied, and a draft of the commendable/practical guide was made and discussed in the meeting of specialists. (NEDO)

New Sunshine Program for Fiscal 2000. International cooperative project for developing photovoltaic power system practicalization technology (International Energy Agency (IEA)/Cooperative Program on Photovoltaic Power Systems (PVPS) implementing agreement - Task 1); 2000 nendo New sunshine keikaku. Taiyoko hatsuden system jitsuyoka gijustu kaihatsu kokusai kyoryoku jigyo (IEA taiyoko hatsuden system kenkyu kyoryoku program jisshi kyotei task 1)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Fiscal 2000 participation in the above-named program is reported. At the Task 1 meeting of experts, electric power application in the participating countries was taken up and information was exchanged concerning the technical, economical, and environmental facets of photovoltaic power generation, efforts were made to disseminate the technology to non-participating countries, and coordination was established between the Tasks. For the preparation and publication of the ISR (International Survey Report), Japan would prepare and submit its NSR (National Survey Report) on Japan's photovoltaics-related policies, amounts of introduction and production, etc. The ISR was to be compiled by technical writers based on the NSRs submitted by the countries involved, to be bound into a book by September after supervision by the Task 1 staff and the executive committee. As for Market Implementation, it would be compiled under the leadership of Germany, Sweden, Denmark, Norway, and Japan. An added-value workshop was held at Glasgow, the United Kingdom, in May 2000 with the participation of 53 representing 14 countries. (NEDO)

FY 1998 report on the results of the New Sunshine Project - Development of the commercialization technology of the photovoltaic power system. Verification study of the photovoltaic power system - Research on engineering methods for cost effective PV installation; 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden system no jissho kenkyu (tashu secchi koho no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For the purpose of promoting installations of PV system and making use of the unused space for which a rise in the PV demand equal to that in houses, building roofs, etc. is expected, examination/research for much newer forms of land installation are proceeded with, and evaluation/verification of reliability/durability are conducted of new installation processes using thin film solar cells, adhesives, etc. In this fiscal year, study of the development/verification of low cost floating pedestal was promoted, and at the same time, examinational study of forms of land installation was made. As to the development of low cost floating pedestal, the module type flexible floating pedestal was developed as a small prototype pedestal and tested for installation in a pool. Survey was also carried out of geometry, mooring systems, materials, design conditions, and existing instances of different floats, and measures were studied for the effective use of the floating system. In relation to reliability and durability evaluation of the new installation process, the verification operation of evaluation facilities for various installation processes was continued, and the power generation capacity was made clear in special forms of installation such as installations on vertical/horizontal surfaces. And the study was made of the large area frameless structure, building use double glass structure, and durability of the adhesive/adhesive tape process of thin film solar cells. (NEDO)

Fiscal 1994 research report. Demonstration test for establishing technology for peakload shaving with dispersed small residential PV systems (Evaluation of weatherability of house-use solar light electric power generating system equipment); 1994 nendo jutakuyo taiyoko hatsuden fuka heijunka gijutsu nado kakuritsu jissho shiken ni kansuru kaiseki hyoka no uchi jutakuyo taiyoko hatsuden system kiki no taikosei hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

Weatherability tests such as exposure to the atmosphere are conducted to collect and accumulate information on the degradation of house-use photovoltaic equipment expected to come into use in areas where weather conditions are hostile. Based on the thus collected data, analysis and evaluation are conducted about the mechanisms of corrosion and degradation for the establishment of designing and evaluating methods for maintaining weatherability. Since fiscal 1994 is the first year of the project, preparations are made for tests to be conducted. In carrying out research activities, a Weatherability Evaluation Committee for House-Use Solar Light Electric Power Generating System Equipment is organized, who discuss implementation of the project. Discussion is made on the shape and structural materials of the exposure rack. An aluminum alloy coated with a clear coating of alumite sulfate is selected, and a rack is built. Specifications of a sea salt particle collector are discussed, and preparations are made for arresting and quantifying sea salt particles under the Japanese Industrial Standard (JIS) dry gauze method and the International Organization for Standardization (ISO) wet candle method. Solar cell module initial characteristics are measured. (NEDO)

Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Research and development of photovoltaic power utilizing system and peripheral technologies (Study of peripheral device for AC module); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (AC module yo shuhen sochi no kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For widening the application of photovoltaic power generation, the AC (alternating current) module technology was examined for validity, and effective ways to utilize the technology and tasks to solve for its further development were studied. In fiscal 1999, concerning the validity of the AC module technology, it was shown quantitatively that attention should be paid to the inhibition of radio interference although the AC module was the more advantageous when under the influence of shadow. In the study of various measures for utilizing the technology, it was shown that, although the technology contained many tasks to discharge, such as need for downsizing and cost reduction, improvement on environmental resistance, and the prevention of radio interference, yet it had many advantages expected to turn up in the future, such as reduced influence of shadow, high flexibility in system design, and decreased installation cost. In the study of technical tasks to discharge in the course of development, it was stated that AC module integrated inverters (MICs) were already on the market, that an autonomous distributed type system control method suited the purpose of AC module systems, and that it was important to develop a thin MIC technology for application in the next generation. (NEDO)

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Research and development of photovoltaic system evaluation technology (Research, development, and survey of crystalline solar cell evaluation system); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu (kesshokei taiyo denchi hyoka system no kenkyu kaihatsu chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In the basic study of ultrahigh-efficiency cells, the technology of ribbon crystal growing is again attracting attention for shortage of Si material supply. The new technology and problems to solve for cost reduction for it are discussed. Concerning the bulk type crystalline Si which is a core material, recent trends are mentioned involving studies of basic substrate properties such as the photoabsorption coefficient and crystal defects for achieving higher efficiency, development of gettering and surface passivation technologies, enhancement of processing speeds, radiation concentration behavior, etc. Newly obtained findings about photodegradation are mentioned, and some remedial measures are described. Recent reports on the application of porous Si to solar cells are compiled. In connection with the development of low-cost quantity-production process technologies, a remarkable progress recently marked by polycrystalline Si solar cells is described. Furthermore, it is stated that new process technologies will be required in the fields of material refining, substrate manufacturing, and cell fabrication. A proposition is presented aiming at developing cell modules compatible with application systems and practicalizing modules that may be integrated with roofing materials. Reference is also made to surveys overseas. (NEDO)

Report on achievements in fiscal 1998. Development of technologies to put photovoltaic power generation systems into practical use - Demonstrative research on photovoltaic power generation system (Study on grid interconnection technique for dispersed photovoltaic systems under high-density connection); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden system no jissho kenkyu (komitsudo renkei gijutsu no kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Interconnecting photovoltaic systems with power transmission systems under high density affects power quality, protection, maintenance and stability of the transmission lines. As measures to deal with this issue, investigations are being made on (1) elucidation of effects imposed on transmission lines, (2) establishment of countermeasure technologies, and (3) technological options leading to higher value addition. In Item (1), with an objective to identify the current status, evaluations were given on prevention of independent operation of commercially available inverters, and on their stabilizing performance against system fluctuation. The evaluations were performed by conducting a test for multiple unit operation in parallel and a single unit performance test. The test result indicated that, while the prevention performance can be satisfied, maloperation has occurred frequently due to the system fluctuation, and that voltage rise due to the inverter was suppressed effectively by using the simultaneous control of active and reactive powers. In Item (2), a demonstration test was launched on an inverter incorporating a new prevention device. The effective means to suppress voltage rise in the high-voltage power transmission lines is the discrete voltage suppression by controlling reactive power. In addition, a proposal was made on a new voltage and phase detection method that can be used at short circuit of the high-voltage transmission lines. In Item (3), having a photovoltaic system contain a small size batteries was found effective in suppressing the power generation output variation, and in smoothing the loads. (NEDO)

New Sunshine Program for Fiscal 2000. International cooperative project for developing photovoltaic power system practicalization technology (International Energy Agency (IEA)/Cooperative Program on Photovoltaic Power Systems (PVPS) implementing agreement - Task 1); 2000 nendo New sunshine keikaku. Taiyoko hatsuden system jitsuyoka gijustu kaihatsu kokusai kyoryoku jigyo (IEA taiyoko hatsuden system kenkyu kyoryoku program jisshi kyotei task 1)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Fiscal 2000 participation in the above-named program is reported. At the Task 1 meeting of experts, electric power application in the participating countries was taken up and information was exchanged concerning the technical, economical, and environmental facets of photovoltaic power generation, efforts were made to disseminate the technology to non-participating countries, and coordination was established between the Tasks. For the preparation and publication of the ISR (International Survey Report), Japan would prepare and submit its NSR (National Survey Report) on Japan's photovoltaics-related policies, amounts of introduction and production, etc. The ISR was to be compiled by technical writers based on the NSRs submitted by the countries involved, to be bound into a book by September after supervision by the Task 1 staff and the executive committee. As for Market Implementation, it would be compiled under the leadership of Germany, Sweden, Denmark, Norway, and Japan. An added-value workshop was held at Glasgow, the United Kingdom, in May 2000 with the participation of 53 representing 14 countries. (NEDO)

Survey for making a data book on the new energy technological development (photovoltaic power generation); Shin energy gijutsu kaihatsu kankei data shu sakusei chosa (taiyoko hatsuden)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Data on the photovoltaic power generation are synthetically collected, systematized, and summarized as a data book on the photovoltaic power system. Main details are as follows: photovoltaic power systems were listed by usage, by size of power generation, and by authority concerned. Significance of adopting the photovoltaic system is stated at each level of each user of the country, local governments and individuals. As to the present situation of the solar cell market, solar cells were arranged in terms of production volume by region, production volume by type, production volume by company, shipment by usage, production amount, and price. With regard to policies of each country on the photovoltaic power system, those of advanced countries including Japan were summed up. Concerning the introduction of the system in each country, examples of the introduction were made clear, and at the same time the estimated volume of and the target for introduction of the photovoltaic power system were summarized. In respect to the subsidy system for the introduction of the photovoltaic power system, arranged were the subsidy system, the preferential tax system and the loan system.

NEDO Forum 2000. Solar technology development session (photovoltaic power generation system and our living); Taiyoko gijutsu kaihatsu session. Taiyoko hatsuden system to watashi tachi no kurashi

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-09-01

The following themes were presented at the present session: (1) energy and environmental problems, and expectation to the photovoltaic power generation system, (2) our living and photovoltaic power generation, and (3) energy policies of Kobe Municipality based on lessons from the earthquake disaster. Item (1) describes: if the total electric power obtained in 20 years from the photovoltaic power generation system of 3 kW output for residential houses is converted into amount of petroleum consumed by thermal power plants, it corresponds to about 850 twenty-liter polyethylene tanks; to build a photovoltaic power generation system, energy corresponding to about 100 polyethylene tanks is used; therefore, subtraction results in saving of about 750 tanks; ordinary houses discharge about 3,500 kg of CO2 annually; and the photovoltaic power generation system serves to reduce about 1,000 kg of CO2 emission annually. Item (2) describes: in markets in 2010, more than 80% of the power generation system is served for housing; profitable price of power generation value is about 55/kW; more than 50% of the value is occupied by the value for other than power generation; and more than 80% of the system for housing will be of roof-material type in 2005. Item (3) introduces the energy diversification taken by Kobe Municipality after the earthquake disaster, and the energy policies, including the 'life spot' policy. (NEDO)

Field tests of photovoltaic power generation at the Fukuroi Mitsukawa Hospital in Fukuroi City, Shizuoka Prefecture; Fukuroishi Mitsukawa byoin taiyoko hatsuden field test jigyo (Shizuokaken Fukuroishi)

Energy Technology Data Exchange (ETDEWEB)

Namikawa, K

1996-05-30

A 30 kW-scale photovoltaic power generation system has been installed on the roof of an existing hospital. Various data have been collected to prove the applicability and stability of the system. The system was designed so as to be suitable for installing on the roof with high-wind. Structures of the frame and base were decided by considering the load and high-wind. The selection of design and materials for this system on the roof with high-wind due to the topography is expected to be technically proven. This field test is the first for private hospitals. The power can be supplied to medical equipment during outage at disasters. The introduction of a system having the self-function is also the first case. Brochure illustrating the outline of this system and the mechanism of photovoltaic power generation system was made and distributed to the public offices, hospitals, and visitors inside and outside the prefecture. Effectiveness of the photovoltaic power generation system has been positively diffused. A display board showing various conditions is placed in the entrance lounge, to diffuse and promote the system. 12 figs., 1 tab.

Report `A field test project for the disaster prevention type photovoltaic power generation (Kobe city, Hyogo prefecture)`; `Bosaigata taiyoko hatsuden field test jigyo (Hyogoken Kobeshi)` hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-09-12

An experiment was conducted on the introduction of the disaster prevention type photovoltaic power system provided with storage batteries to public facilities, etc., considering not only the use of new energy from the environmental aspect, but the emergency use. In fiscal 1995, 5kW-output photovoltaic power systems were installed on the rooftop of Hiyodori and Takamaru regional welfare centers and a 30kW photovoltaic power system on the rooftop of the Hyogo Ward Office. Demonstrative tests of these systems started for collection of various data. Now that the systems were installed at the regional welfare center managed mostly by regional citizens and the ward office which is an administrative office familiar with regional residents, the understanding of and familiarity with the photovoltaic power system were obtained from regional residents, and also people were enlightened on the use of solar energy in such a point as economization of power rates using the interconnected power system. Further, for life supports, it was made possible to secure minimum electric power in emergency and to secure functions of disaster prevention spots. 3 figs.

Fundamental study on PV system for floating water power device `Mighty Whale`; Okiai futaishiki haryoku sochi `Mighty Whale` eno taiyoko hatsuden sochi tosai no kihon kento

Energy Technology Data Exchange (ETDEWEB)

Washio, Y [Japan Marine Science and Technology Center, Kanagawa (Japan)

1996-10-27

Studied in this paper is the use of a photovoltaic power generation system in combination with a wave energy conversion system to cover the latter`s weak point that it is available but intermittently. An offshore floating wave power device Mighty Whale (MW) is described, which will have a wave energy absorbing air chamber in the front and an anti-rocking float that looks like a whale in the rear. The movement, up and down and back and forth, of the water surface in the air chamber due to incident waves turns the power generator turbine. Out of the space available on the MW, a 200m{sup 2} area has been specified as the place suitable for the installation of solar cells capable of a maximum output of 20kW, for which specification the elevation of the sun has been taken into account. Batteries will routinely be supplied with power in parallel from the wave activated and photovoltaic devices, the supply will be limited when the batteries are fully charged, and an auxiliary power generator will be run in case of shortage. Power that can be provided by a 20kW solar array was calculated using actual data of sunshine on the slope for each array orientation, and required battery capacity was calculated for each solar array orientation. Important items for consideration for the insurance of reliability on the ocean include measures against salt damage, detailed designing of wiring, and coordinated operation of photovoltaic and wave activated power generation systems. 3 refs., 6 figs., 5 tabs.

FY 1994 report on the survey and research of introduction, promotion of proliferation and guidance on new energy introduction. Pt. 2; 1994 nendo shin energy donyu fukyu sokushin shido ni kansuru chosa kenkyu. 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

Survey, collection and analysis were performed on different items of information required for new energy technologies. Studies were carried out to structure a system to support smooth execution of technical guidance and consultation. Among the project areas for field tests on photovoltaic power generation systems for public facilities, measurements were executed on hourly power demand in facilities in snowy and cold districts with little data available. In putting different items of information into a database, data were collected and put into order for the following items: statistics on average value for ten years of insolation time in 842 locations nationwide, calculation of insolation on slanted surface at the insolation measuring points (slanting angles and insolation on the slanted surface at which energy amount available for power generation is maximized in a year, as obtained by estimating the insolation on horizontal surface from the insolation duration), and expansion and addition of the introduction examples. Specifications for solar cell modules and inverters were classified and put into order, and so were on types, specifications, and product descriptions for photovoltaic power generation systems for individuals' houses. The aid system structured in the previous year was discussed for improvement, and new information was put into a database to improve the aid system. (NEDO)

Survey report for fiscal 1999. Reference book for standard heat calculations in high-performance industrial furnace introduction field test project; 1999 nendo koseino kogyoro donyu field test jigyo chosa hokokusho. Hyojun netsu keisanshiki kijunsho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective to verify in a short time the heat recovery capability being the evaluation parameter for the technologies to develop the high-performance industrial furnace, a standard calculation book will be prepared, which standardizes the data collection methods and heat calculation methods, and is used as the standard data sheets and bases. Evaluations and analyses will be given on business types, furnace constructions, thermal technologies, and functions in the research items adopted in the field test project. The results will be used to recognize the business entities engaged in the project in the next fiscal year, furnace types and sizes, establish the industrial furnace subjected to researches in the next fiscal year, and proliferate and expand the related business entities. Standard data sheets will be prepared on seven kinds of furnaces, heating furnaces (continuous and batch types), ladles, heat treatment furnaces (continuous and batch types), gas treatment furnaces, and melting furnaces. The standard data sheets will cover the following items: evaluation parameters (energy saving rate, thermal efficiency, and waste heat recovery rate), calculating conditions to be the base for the evaluation parameters, a heat production book to be the base for calculating the heat unit requirement, and a standard calculation book to be the base for the heat production table. The standard data sheets (including the standard calculation book) and floppy disks are submitted. (NEDO)

FY 1998 annual report on the survey on development, introduction and promotion of urban type multipurpose geothermal utilization techniques; 1998 nendo toshigata tamokuteki chinetsu riyo gijutsu no kaihatsu, donyu, sokushin ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Introduction of geothermal heat pump systems, which depend on temperature differential, is investigated for urban areas, which have large energy demands. Results of the surveys on the current situations of geothermal heat pump (GHP) systems indicate that they have already numbered 300,000 units in USA and totaled more than 50,000 units in Switzerland and Northern European countries, and that they are increasing at an annual rate of higher than 10%. The results also indicate that introduction of these systems are well feasible in Japan, which generally has better topographical conditions than American and European countries, and the GHP system with vertical ground heat exchanger is investigated for its topographical and environmental considerations. These systems could annually abate approximately 52 million tons of CO2 (4.3% decrease), if disseminated to all households. They are also expected to help control the heat island phenomenon, and reduce peak power consumption. The technological problems to be solved before these systems are massively disseminated including development of small scale drilling rigs and preparation of drilling manuals. System standardization and introduction of subsidy systems are also needed to massively disseminate these systems. (NEDO)

FY 1994 report on the survey and research of introduction, promotion of proliferation and guidance on new energy introduction. Pt. 2; 1994 nendo shin energy donyu fukyu sokushin shido ni kansuru chosa kenkyu. 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

Survey, collection and analysis were performed on different items of information required for new energy technologies. Studies were carried out to structure a system to support smooth execution of technical guidance and consultation. Among the project areas for field tests on photovoltaic power generation systems for public facilities, measurements were executed on hourly power demand in facilities in snowy and cold districts with little data available. In putting different items of information into a database, data were collected and put into order for the following items: statistics on average value for ten years of insolation time in 842 locations nationwide, calculation of insolation on slanted surface at the insolation measuring points (slanting angles and insolation on the slanted surface at which energy amount available for power generation is maximized in a year, as obtained by estimating the insolation on horizontal surface from the insolation duration), and expansion and addition of the introduction examples. Specifications for solar cell modules and inverters were classified and put into order, and so were on types, specifications, and product descriptions for photovoltaic power generation systems for individuals' houses. The aid system structured in the previous year was discussed for improvement, and new information was put into a database to improve the aid system. (NEDO)

Fiscal 2000 report of investigation. Research on effective use of technology for biomass waste and diffusion scenario of the technology; 2000 nendo biomass kei haikibutsu no yuko riyo gijutsu to sono fukyu scenario no chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Examination and proposal were made on the effective uses of technologies for biomass wastes and on the diffusion scenarios, with trial calculations done to find the maximum reducible amounts in terms of carbon dioxide. In the examination of the systems, it was focused on five technologies, namely, direct combustion of straw and rice straw/CHP/heat utilization, synthesis of gasified methanol from demolition wood, biogas/CHP from livestock feces and urine, conversion to ethanol through saccharification of used paper, and conversion to biodiesel from vegetable waste oil; the examination also covered each feature, core function, use situation inside and outside Japan, technological system for each energy conversion, etc. Further, solutions were examined and proposed concerning diffusion barriers in each scenario. Consequently, the maximum amount of CO2 reduction effect was found respectively 217 thousand t-C in the straw and rice straw, 500 thousand t-C in the demolition wood, 9.53 million t-C in the livestock feces/urine, 820 thousand t-C in the used paper, and 30 thousand t-C in the vegetable waste oil. (NEDO)

FY 2000 Report on survey results. Curtailment of the carbon dioxide emission by effective use of woody biomass system waste; 2000 nendo mokushitsu biomass kei haikibutsu no yuko riyo ni yoru nisanka tanso haishutsu no sakugen

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

It is estimated that the woody biomass resources in Japan total 42.70 million t/y on a dry basis (indigenous production: 20.00 million t/y), which corresponds to 18.00 million t/y as oil. This project studies effective utilization of low-quality biomass resources now discarded, e.g., thinning materials and demolition woods, by reference to biomass utilization pursued in European and North American countries. The study activities cover the 3 areas of woody biomass wastes, current status of biomass utilization technologies in the overseas countries, and feasibility of introduction of the utilization technologies, after investigating necessity of abatement of the green-effect gases, current status of energy demands and policies, and woody biomass. Utilization of biomass resources for low-temperature heat purposes, which is the central issue in Japan, is not well established both technologically and politically. Moreover, the biomass resources are not exposed to price competition. Based on these premises, a total of 6 scenarios are proposed to promote utilization of biomass resources, including power/heat co-generation at a wood processing center, and dual firing at existing coal-fired boilers. (NEDO)

Report on the project for spread/promotion of technology for the industrial waste optimized treatment in the Asian region (International Symposium `98); Asia chiiki sangyo haikibutsu tekiseika shori gijutsu nado fukyu sokushin jigyo (symposium kaisai) hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

In Japan and Asian countries, the optimized treatment of industrial waste is the problem with the economic growth. Border-crossing movement of the waste for promotion of the renewable use is also a problem. Therefore, the International Symposium `98 on the industrial waste problem in the Asian region was held. China, Thailand, the Philippines and Korea were invited to Japan to give lectures. MITI of Japan reported on the present situation of Japan and the cooperation with Asian countries. The industrial circle reported on efforts for environmental protection measures to be taken, the industrial waste problem at companies which advanced into Asian countries, effects of the Basel Convention on recycling activities, Japan`s role in Asia, etc. In the panel discussion, promotion of cooperation for recycling technology and Japan`s support for formulating strategy on the industrial waste were requested to Japan, and the construction of an Asian area network was proposed. Concerning the cooperative system between governments and private companies, it was concluded that it was necessary to discuss it considering the actual state of each country. Importance of recycle and information exchange was realized again. 10 refs., 15 figs., 27 tabs.

Fiscal 1976 Sunshine Project result report. Research on solar energy utilization systems (photovoltaic power generation); 1976 nendo taiyo energy riyo system chosa kenkyu seika hokokusho. Taiyoko hatsuden

Energy Technology Data Exchange (ETDEWEB)

NONE

1977-03-01

This report describes the fiscal 1976 research result on the technical and economical perspectives of various solar cells, high-efficiency solar cell and its evaluation technique, and a photovoltaic power generation system and its applications. On Si single-crystal slice solar cell, it was pointed out that cost reduction by automatic production process using no vacuum process is essential. On Si thin film solar cell, some problems to be solved for development of particle accelerating growth technique were pointed out. Study was also made on 2-6 group compound semiconductor solar cell, 3-5 group bulk crystal solar cell, 3-5 group thin film solar cell, solar collection solar cell, and raw polycrystal Si materials. On photovoltaic power generation systems, it was reconfirmed through reconsideration of power generation systems for every application that the photovoltaic power generation system for residences is promising. On medium- scale power generation systems, study was made on power load and system configuration in consideration of applications to electric railway, highway, and power source of isolated islands. (NEDO)

Research and development of photovoltaic power system. Research on surface passivation for high-efficiency silicon solar cells; Taiyoko hatsuden system no kenkyu kaihatsu. Hyomen passivation no kenkyu

Energy Technology Data Exchange (ETDEWEB)

Saito, T [Tokyo Univ. of Agriculture and Technology, Tokyo (Japan). Faculty of Technology

1994-12-01

This paper reports the result obtained during fiscal 1994 on research on surface passivation of high-efficiency silicon solar cells. In research on carrier recombination on SiO2/doped silicon interface, measurements were carried out on minority carrier life with respect to p-type silicon substrates with which phosphorus with high and low concentrations are diffused uniformly on the surface and non-uniformly on the back and then oxidized. The measurements were performed for the purpose of evaluating the carrier recombination at p-n junctions. Effective life time of oxidized test samples increased longer than that of prior to the oxidization as a result of effect of surface passivation contributing remarkably. In research on reduction in carrier recombination on SiO2/Si interface by using H radical annealing, experiments were conducted by using a method that uses more active H-atoms. As a result, it was revealed that the reduction effect is recognized at as low temperature as 200{degree}C, and photo-bias effect is also noticeable. Other research activities included analytic research on minority carrier recombination on micro crystalline silicon/crystalline silicon interface, and experimental research on evaluation of minority carrier life of poly-crystalline silicon wafers. 6 figs.

Photovoltaic power generation field test at Saigo Police Station (police station in a heavy-snow district); Saigo keisatsusho taiyoko hatsuden field test jigyo (sekisetsu chiku no keisatsusho)

Energy Technology Data Exchange (ETDEWEB)

Matsuo, S. [Shimane Prefectural Police Department, Shimane (Japan)

1997-05-30

Contents of a fiscal 1996 photovoltaic power generation field test at a police station in a heavy-snow district are reported. The system is on the rooftop of the garage of Saigo Police Station, Saigo-cho, Shimane Prefecture, and is used for lighting, airconditioning, etc., in the police station. It is 15kW in capacity and operates on high-voltage interconnection (with back flow). The array is a 9-series/17-parallel (polycrystalline modules) system, facing 15deg eastward from due south and inclined at an angle of elevation of 17deg. Dead space on the roof is used for solar cell installation, and the applicability and stability of the photovoltaic power generation system, as installed at a police station in a heavy-snow district, were verified and, at the same, operation data were collected. The data will serve as guidelines for construction in the future, and will enable understanding about how a distributed type power generation plant should be on an isolated island. The compilation of various data about its system interconnection (with back flow) with the commercial power source is meaningful because it will work effectively in popularizing the photovoltaic power generation system. Efforts to appeal to the local population are under way, which includes letting visitors into a terrace, distributing advertising pamphlets, etc., which are quite effective in enlightening people of the new energy producing technology

Report on construction of thermal power plants for industrial use in China in FY 1997; 1997 nendo chosa hokokusho (Chugoku ni okeru kogyoyo karyoku hatsuden setsubi secchi)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Steam supply and power generating plants in China can be classified into systems for district heating and power generation and systems for steam supply and power generation for industrial use. Steam supply and power generating plants for district heating in winter season are diffused due to the introduction of Russian technology. There are steam supply and power generating plants for supplying steam to manufacturing equipment in works and generating power for industrial use. Both of these are called heat and power stations. This survey was conducted for the latter thermal power generation plants for industrial use. China has heat and power stations with a total capacity of 22,000 MW, and a half of them are used for district heating. Although the thermal efficiency of usual thermal power generation plants is between 30 and 40%, that of heat and power stations is between 60 and 70%. Latent demand of such power generation plants for industrial use is large. Problems for the diffusion were extracted. It was considered that steam supply and combined power generating plants using natural gas are effective when constructed in large cities, in the vicinity of large cities, or in technological universities. 22 figs., 15 tabs.

Introduction of anti-rolling active vertical fin and its application to maneuverability for displacement-type super high speed ship. 2nd Report.; Haisuiryogata chokosokusen no yokoyure seishiyo active suichoku fin no donyu to sojuseieno oyo

Energy Technology Data Exchange (ETDEWEB)

Hirayama, T; Saito, Y [Yokohama National University, Yokohama (Japan). Faculty of Engineering; Niihara, Y [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan)

1997-12-31

Discussed herein are the effects of vertical fin projecting downwards from the bottom of a displacement-type superhigh-speed ship, installed to improve its transverse stability and turning ability. The system for simultaneously controlling rudder and vertical fin by the optimum regulator was studied for maneuverability in directional following waves and smooth water, and maneuverability was simulated numerically. A ship is greatly rolled and sloped when running in waves. It is found that the vertical fin shows a high anti-rolling effect when the ship runs straight. The optimum regulator greatly improves maneuverability in waves, reducing rolling by 92%. Increased rolling with the vertical fin, observed in the previous study in directional following waves, is found to be due to the rudder. The optimum position of the fin is determined to control transverse sloping of a turning ship in a superhigh-speed region. 21 refs., 12 figs., 4 tabs.

Report on survey in fiscal 2000. Survey on introduction of external accreditation system in engineer education (electronic information communications); 2000 nendo chosa hokokusho. Gijutsusha kyoiku no gaibu ninteiseido donyu ni kansuru chosa (Denshi joho tsushin)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In order to ensure international applicability of engineer education such as in universities and other organizations, and to improve the environment to supply human resources demanded by economic societies, surveys were performed on the external accreditation system for engineer education such as in universities and other organizations. In the field of electronic information communications, a committee to correspond to JABEE was established to perform system build-up, where the discussions were advanced. This field was classified into the following four specified areas: general aspect of electric/electronic/information communication engineering, electronics, information communications, and information systems. A supplementary explanation was given on the educational contents except for the information systems, based on which the self-assessment criteria and the evaluation table (for trial use) were prepared. For the examiner training, instructors were invited from ABET in the U.S.A., and training meetings were held. In addition, two committee members were sent as observers to the examinations being carried out at ABET. The trial experiments were conducted for the information communications program at the engineering department of Niigata University, and the electronic system engineering class at Sendai Radio Wave Industrial College. This paper summarizes the results of the examinations. (NEDO)

Introduction of anti-rolling active vertical fin and its application to maneuverability for displacement-type super high speed ship. 2nd Report.; Haisuiryogata chokosokusen no yokoyure seishiyo active suichoku fin no donyu to sojuseieno oyo

Energy Technology Data Exchange (ETDEWEB)

Hirayama, T.; Saito, Y. [Yokohama National University, Yokohama (Japan). Faculty of Engineering; Niihara, Y. [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan)

1996-12-31

Discussed herein are the effects of vertical fin projecting downwards from the bottom of a displacement-type superhigh-speed ship, installed to improve its transverse stability and turning ability. The system for simultaneously controlling rudder and vertical fin by the optimum regulator was studied for maneuverability in directional following waves and smooth water, and maneuverability was simulated numerically. A ship is greatly rolled and sloped when running in waves. It is found that the vertical fin shows a high anti-rolling effect when the ship runs straight. The optimum regulator greatly improves maneuverability in waves, reducing rolling by 92%. Increased rolling with the vertical fin, observed in the previous study in directional following waves, is found to be due to the rudder. The optimum position of the fin is determined to control transverse sloping of a turning ship in a superhigh-speed region. 21 refs., 12 figs., 4 tabs.

Report for fiscal 1998 on industrial waste optimized treatment technologies dissemination and promotion business for asian region. Holding a symposium; 1998 nendo chosa hokokusho. Asia chiiki sangyo haikibutsu tekiseika shori gijutsu nado fukyu sokushin jigyo (symposium kaisai)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

An International Symposium on the Asian Industrial Waste Issue was held in Tokyo on 4 February 1999, where lectures were delivered by participants representing China, the Philippines, Thailand, Malaysia, and Japan. More 150 people attended the event, with questions and answered animatedly exchanged between the lecturers and the audience. The progress of urbanization is quite rapid in China, with the quantity of waste increasing every years to justify the anticipation that there will be a very sharp increase in refuse incineration in the near future. Raising a serious problem in China these days is the plastic waste. In the Philippines, there are no private-sector waste treatment/disposal facilities and corporations are not obliged to take care of their waste. Consequently, very little treatment or recycling is being undertaken. In Thailand, although waste treatment/disposal centers are in operation financed by the Government and private sectors, the cost is very high, and the Government policy is that private investment will be encouraged and supported in future. In Malaysia, privatization is in progress of the business of managing waste in the solidified form. A comprehensive waste treatment/disposal plant was completed in 1998 by the endeavors of a Denmark-Malaysia consortium, and is in operation since then. (NEDO)

FY 1998 report on the waste processing/recycling related technology, 'The R and D of lead-free solder standardization'; 1998 nendo haikibutsu shori recycle kanren gijutsu seika hokokusho. Namari free handa kikakuka nado kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

To reduce the environmental pollution caused by lead eluted from the electronic equipment waste, the R and D on lead-free solder were conducted and the results were summarized. As to the basic characteristics, the evaluation test method was studied in terms of the range of melting temperature, mechanical strength, wettability and joint strength, to select a uniform test method. As the lead-free solder, Sn-Ag alloys were mainly used and mixed in a combination of Cu, Bi and In. Changes in characteristics were made clear by adding trace elements such as Ge, Mn and P. Relating to the applied characteristics, in selection of solder materials, materials were selected for which evaluation of the commercialization is proceeded with from a viewpoint of promotion of commercialization. Concerning the experimental evaluation of characteristics of lead-free solder in mounted substrates, it was indicated that basically lead-free solder can be practically used. Further, it was indicated that the Sn-Ag-Cu-Bi system depends not on solder composition but on active force, printing accuracy and flux characteristic of solder paste, that improvement of solder paste has an effect on mounting characteristics. (NEDO)

FY 1992 report on the development of wood-waste/agri-waste pyrolytic gasification technology and utilization technology of gas product; 1992 nendo mokushitsukei haikibutsu no netsubunkai gas ka gijutsu to seisei gas no riyo gijutsu kaihatsu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

It is urgently necessary for the Philippines, which has no promising energy source to replace imported oil and lacks hard currencies, to reduce dependence on oil. The country, consisting of a number of islands, has faced many difficulties in construction of large-scale power transmission grids covering wide areas, which greatly retard development of local industries and dissemination of electricity. Therefore, great expectations have been placed on the techniques this project plans to develop for utilization of wastes as the energy source. This 5-year project (FY 1990 to 1994) is aimed at joint research and development of (thermal decomposition/gasification and power generation system) for transforming large quantities of wood-wastes/agri-wastes left unutilized into electric power, in which thermal decomposition/gasification of the wastes is combined with gas engine/power generator systems, and thereby to establish the systems suitable for the developing country. The major R and D results obtained in FY 1992 as the third year include on-the-spot surveys, tests for validating elementary techniques, designs and fabrication of part of the demonstration plant, and invitation of Philippine researchers to Japan. (NEDO)

FY 1991 report on the development of wood-waste/agri-waste pyrolytic gasification technology and utilization technology of gas product; 1991 nendo mokushitsukei haikibutsu no netsubunkai gas ka gijutsu to seisei gas no riyo gijutsu kaihatsu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-03-01

It is urgently necessary for the Philippines, which has no promising energy source to replace imported oil and lacks hard currencies, to reduce dependence on oil. The country, consisting of a number of islands, has faced many difficulties in construction of large-scale power transmission grids covering wide areas, which greatly retard development of local industries and dissemination of electricity. Therefore, great expectations have been placed on the techniques this project plans to develop for utilization of wastes as the energy source. This 5-year project (FY 1990 to 1994) is aimed at joint research and development of (thermal decomposition/gasification and power generation system) for transforming large quantities of wood-wastes/agri-wastes left unutilized into electric power, in which thermal decomposition/gasification of the wastes is combined with gas engine/power generator systems, and thereby to establish the systems suitable for the developing country. The major R and D results obtained in FY 1991 as the second year include on-the-spot surveys, tests for validating elementary techniques, designs and fabrication of part of the demonstration plant, and invitation of Philippine researchers to Japan. (NEDO)

FY 1994 report on the development of wood-waste/agri-waste pyrolytic gasification technology and utilization technology of gas product; 1994 nendo mokushitsukei haikibutsu no netsubunkai gas ka gijutsu to seisei gas no riyo gijutsu kaihatsu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

This 5-year joint project (FY 1990 to 1994) by Japan and the Philippines is aimed at joint research and development of (thermal decomposition/gasification and power generation system) for transforming large quantities of wood-wastes/agri-wastes left unutilized in the Philippines into electric power, in which thermal decomposition/gasification of the wastes is combined with a gas engine system. The field tests of the demonstration plant successfully produce power of 100 kW by burning only the low-calorie gas with a heating value near critical level for self-sustained combustion, obtained by gasification of sawdust by the fluidized gasifier and refined, attaining the object of the project. It is confirmed that a 200 to 300 kW class commercial plant can be designed and constructed basically by scaling up the 100 kW demonstration plant. The other data obtained by the field tests include those for improved operability and maintainability, gas purification, and reducing sizes of the facilities, including utility facilities. (NEDO)

FY 1990 report on the development of wood-waste/agri-waste pyrolytic gasification technology and utilization technology of gas product; 1990 nendo mokushitsukei haikibutsu no netsubunkai gas ka gijutsu to seisei gas no riyo gijutsu kaihatsu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-03-01

It is urgently necessary for the Philippines, which has no promising energy source to replace imported oil and lacks hard currencies, to reduce dependence on oil. The country, consisting of a number of islands, has faced many difficulties in construction of large-scale power transmission grids covering wide areas, which greatly retard development of local industries and dissemination of electricity. Therefore, great expectations have been placed on the techniques this project plans to develop for utilization of wastes as the energy source. This 5-year project (FY 1990 to 1994) is aimed at joint research and development of (thermal decomposition/gasification and power generation system) for transforming large quantities of wood-wastes/agri-wastes left unutilized into electric power, in which thermal decomposition/gasification of the wastes is combined with gas engine/power generator systems, and thereby to establish the systems suitable for the developing country. The major R and D results obtained in FY 1990 as the initial year include negotiations with the Philippines, on-the-spot surveys for the demonstration plant sites and conditions, and conceptual designs of the demonstration plant. (NEDO)

Achievement report for fiscal 2000 on investigations and researches on promotion of utilization of waste energies that can deal with environmental load suppression; 2000 nendo kankyo fuka yokusei taio haikibutsu energy riyo sokushin chosa kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This paper describes the achievements in fiscal 2000 in investigating generation mechanisms and suppression of dioxins from refuse incinerators, and in investigating non-bromine flame retardant materials (having a possibility of generating hazardous material such as bromine-based dioxin during combustion). To produce poly-chlorinated dibenzo-para-dioxins (PCDDs)/PC dibenzo furans (PCDFs) (dioxins, but not containing Co-PCB) in a small fluidized bed combustor for simulated refuse derived fuel (RDF), both of chlorine source and hydrocarbon are required. If the primary combustion furnace temperature is high and the air excess rate is low, the concentration of the dioxins increase. In addition, since oxygen shortage in temporal and spatial locals or excessive concentration zone of unburned hydrocarbons imposes great effect, promotion of turbulence mixing is important. In producing dioxins, vaporization from dust due to interference with the combustion gas, and copper and iron catalysts have great effect, whereas SOx in the combustion gas has suppression effect. Flame retardant materials can provide specific flame retardation effect to particular plastics in a temperature zone slightly lower than the combustion temperature. The paper also describes development of new flame retardant materials. (NEDO)

Report on results of feasibility study in fiscal 1986 on use of coal in next generation high efficiency power generation system - research commissioned by Moonlight project propulsion room of Agency of Industrial Science and Technology. MHD generation subcommittee; 1986 nendo jisedai kokoritsu hatsuden system no sekitan gas riyo feasibility chosa kenkyu seika hokokusho (Kogyo Gijutsuin Moonlight keikaku suishinshitsu itaku chosa). MHD hatsuden bunkakai

Energy Technology Data Exchange (ETDEWEB)

NONE

1987-03-01

A research study was done on MHD generation by coal gasificating combustion. MHD generation is a very attractive power generation system such that efficiency is as high as 55%, that preservation of the environment is superior, and that coal can be used as fuel. The open cycle seems suitable for a one million kW class as a base load following up load fluctuation of approximately 20%, while the closed cycle for 200-300 thousand kW class doing daily start-stop. With a mind to a scale of 30 MWt, in the open cycle, R and D is required in such items as a coal gas combustor, generation channel, high temperature air heater, and seed/slag recovery device. In the closed cycle, R and D is required in the generation channel, high temperature helium heater/high temperature valve, seed injection/recovery device, operation technique of helium closed loop, etc.. Moreover, as a total system, development is necessary in the areas of conceptual design and optimization method, partial load operation and DSS operation method, for example. (NEDO)

FY 1991 report on the results of the development of the entrained bed coal gasification power plant. Part 1. Element study/investigational study of technology/study of the integrated coal gasification combined cycle power system; 1991 nendo seika hokokusho. Funryusho sekitan gaska hatsuden plant kaihatsu - Sono 1. Youso kenkyu hen, gijutsu chosa hen, sekitan gaska fukugo hatsuden system kento hen

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-01-01

For the purpose of establishing the technology of integrated coal gasification combined cycle power generation, the following were conducted: element study of a 200t/d entrained bed coal gasification pilot plant, survey of technology of the coal gasification power generation, study of the practical scale IGCC, etc. The FY 1991 results were summarized. In the gasification test using 2t/d furnace equipment, evaluation test on the test coal for pilot plant was made. In the study of gas turbine combustor for demonstration machine use, measuring duct was fabricated for measurement of combustion gas temperature/pressure, etc. In the simulational study of the total system of combined cycle power generation, review/modification of part of the simulation model and detailing of the model were conducted by comparison with the data on pilot plant operation. In the technology study, joint technology conferences were held for discussions between Japan and Australia, Japan and the U.S., and Japan and Canada. As to the practical scale IGCC, the initially planned output capacity and thermal efficiency were studied based on the knowledge/information obtained through the R and D on the 200t/d pilot plant. (NEDO)

Achievement report for fiscal 2000 on New Sunshine Project aiding program. Development of hot water utilizing power generation plant (Development of binary cycle power plant - development of system to detect well bottom information during geothermal well drilling); 2000 nendo nessui riyo hatsuden plant to kaihatsu seika hokokusho. Binary cycle hatsuden plant no kaihatsu (Chinetsusei kussakuji koutei joho kenchi system no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

R and D has been performed on a system to detect well bottom information during geothermal well drilling (MWD) to identify items of well bottom information during drilling on a real time basis. This paper summarizes the achievements in fiscal 2000. This device measures and transmits to the ground surface the following items during geothermal well drilling at good accuracy under the mud water temperature of 200 degrees C: azimuth, inclination, tool face, bit load, bit torque, temperatures in the device, downhole temperature, and downhole pressure. The current fiscal year has performed improvement of the sonde, including decrease of the sonde length, electric power conservation, enhancement of anti-noise performance, and enhancement of operability. For the sonde performance evaluation, high-temperature test, long distance loop test, and vibration test were carried out. In addition, the experiment analyzing program (for noise processing) was improved. With regard to the well trajectory control aiding system and the well evaluation aiding system, an operation manual was prepared, entitled the 'MWD analyzing system'. Unification was attempted on the hardware of the ground surface detection device system and the analyzing system. (NEDO)

Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Research and development of photovoltaic power utilizing system and peripheral technologies (Research on meteorological data for design optimization); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (saiteki sekkei no tame no kisho data no chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For collecting solar radiation data necessary for the prediction of power to be outputted by photovoltaic power systems in Japan, detailed experiments and observations were conducted with an emphasis placed on the amount of solar radiation on a slope facing north and on the amount of solar radiation broken down by wavelength. Models were analyzed, and the fiscal 1999 results were compiled. In the validation of a model of solar radiation on an inclined surface, a review was conducted using the 1-year data observed at the Takasaki station for all directions, including solar radiation on the slope facing north, and the validity of the model was confirmed. As for the validation of a model for estimating solar radiation by duration of sunshine, it was examined for accuracy using the same data, and was found to be fairly high in accuracy. For the maintenance of solar radiation data for each wavelength, continuous observation was conducted for each wavelength of solar radiation at the Takasaki station using a multi-filter spectroradiometer, and a technique was established to determine spectral distribution using the observed data. Moreover, continuous observation of global diffused solar radiance was conducted using a sky scanner at the said station and solar cell power generation characteristics was continuously monitored. (NEDO)

Report on achievements in fiscal 1998. Development of technologies to put photovoltaic power generation systems into practical use - international joint demonstration and development of photovoltaic power generation systems (Demonstrative research on photovoltaic power and micro hydraulic power hybrid system); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden system kokusai kyodo jissho kaihatsu (taiyoko micro suiryoku hybrid system jissho kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

A photovoltaic (PV) power plant is compounded with a micro hydroelectric (MH) power plant in Vietnam, who has a dry season and a rainy season, to structure a stabilized power supply system to compensate drawbacks of the respective systems. Full load operation is being performed to advance the development of technologies to optimize and improve the performance and reliability of the system. The works include (1) site surveys, and decision on a location to execute the demonstration research, (2) design of the system, and design and fabrication of devices, and (3) the building construction thereof. In Item (1), the location was decided at Trang Village, Vietnam from such installing conditions as annual average insolation, water channels for wheel turbines, energy complementing relations, load demand amount, and difficulty of installation. In Item (2), the system consists of PV:100 kW/MH:25 kW/control system, wherein the MH is an inductive generator. The Main devices include generators, batteries, inverters, system control panels, and a meteorological data recording device. In Item (3) land survey and development were completed. (NEDO)

Fiscal 1997 report on the results of the New Sunshine Project subsidiary operation. Development of a geothermal water use power plant, etc. / technical development of the hot dry rock power generation system (development of electric technology); 1997 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu (koon gantai hatsuden system no gijutsu kaihatsu (yoso gijutsu no kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

For the purpose of using hot dry rock energy to power generation, the R and D was continued of element technology of the hot dry rock power generation. In fiscal 1997, the construction of ground facilities, etc. for long-term circulation experiment was proceeded with to make data analysis for study of the experimental results. As for preparation for the long-term circulation experiment, design/fabrication/construction of experimental facilities were commenced, and review/fabrication of the monitoring system were conducted to strengthen the monitoring network of microearthquakes. In relation to the analytical research, using models connecting reservoirs and wells, relationships were studied among the distance between injection well and production well, production flow rate, and long-term thermal extraction characteristics of reservoirs. Further, to study structures of shallow/deep reservoirs at the Hijiori hot dry rock experimental field, re-determined were mechanism solutions of AE in deep hydraulic fracturing experiments, three well circulation tests, and preliminary circulation tests, and at the same time stress fields were studied. Fracture models were made and the simulation program was revised. 18 refs., 82 figs.

Report on achievements in fiscal 1999. Development of technology to put photovoltaic power generation system into practical use by international cooperation project (Executive Committee meetings for treaty of executing IEA photovoltaic power generation system research cooperation program - IEA/PVPS); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Kokusai kyoryoku jigyo (IEA taiyoko hatsuden system kenkyu kyoryoku program jisshi kyotei (shikko iinkai))

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The 13th and 14th Executive Committee meetings were held. The resolutions adopted at the 13th Executive Committee meeting (Lausanne, Switzerland, May 3 through 5, 1999) were the approval of the Task VIII as a new IEA/PVPS task, the feasibility study on large scale photovoltaic power generation utilizing unused land such as desert (the operating agent country being Japan headed by Mr. Kando, chief researcher at NEDO and Professor Kurokawa) and the Task IX, proliferation of photovoltaic power generation under coordination with developing countries (the operating agent country being England headed by Mr. Bernard McNelis (IT Power) and that the task I operating agent country is substituted jointly by the three countries of Australia, Holland and Switzerland for six months. The resolutions adopted at the 14th Executive Committee meeting (Oslo, Norway, October 18 through 20, 1999) were appointing Australia as the Task I operating agent country headed by Mr. G. Watt, setting a web site of IEA/PVPS, issuing the annual report for fiscal 1998 in early 2000, and holding the Executive Committee meetings for fiscal 2000 in Canada (Quebec, April 17 through 19, 2000), and Italy (October 16 through 18, 2000). (NEDO)

FY 1991 report on the results of the development of an entrained bed coal gasification power plant. Part 2. Support study for the development of an entrained bed coal gasification power plant (Summarization of the operation study); 1991 nendo seika hokokusho. Funryusho sekitan gaska hatsuden plant kaihatsu (Funryusho sekitan gaska hatsuden plant kaihatsu no shien kenkyu) - Sono 2. Unten kenkyu sokatsu hen

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-04-01

The paper summarized the results of the following tests on a 40 t/d pilot plant which were conducted as the support study for the development of an entrained bed coal gasification power plant: dry desulfurization test, dry dedusting test, high-temperature NOx gas combustion test (gas turbine element test). In the dry desulfurization test, tested were the operational automation and monitoring technology, performance of desulfurization, characteristics of load response, sulfur recovery, etc. In the dry dedusting test, tested were the filter medium/dust separation, powder level meter, continuous dust densitometer, operational automation, characteristics of partial load/load response, improvement of filtration materials, test on characteristics of air conveyance, etc. In the high-temperature low-NOx gas combustion test (gas turbine element test), the following were conducted: examination of the test method of gas turbine materials, inspection/examination of the corrosion of gas turbine combustion test device, inspection/examination of the internal corrosion of the stationary blade for gas turbine deposit test, inspection/examination of gasification system. The results of these support studies were reflected one after another in the project on the development of an entrained bed coal gasification power plant. (NEDO)

Fiscal 2000 project of inviting proposals for international joint research - invitation for international proposal (Power generation No.10). Achievement report on independent distributed type power generation technology of using now-unused gas pressure difference energy; 2000 nendo kokusai kyodo kenkyu teian kobo jigyo - kokusai teian kobo (hatsuden No.10). Miriyo gas atsuryokusa energy ni yoru dokuritsu bunsangata hatsuden gijutsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Development is under way of a power generation system utilizing pressure difference during fuel gas transportation, independent from the outside and installable in the vicinity of the load. It is assumed that power is supplied to a decompression device in a fuel gas supply pipeline. Fuel gas placed under high pressure in the mainline is decompressed upon arriving at a consumer area. The intended technology of utilizing the now-unused pressure difference will be employed for power generation, and energy will be collected accordingly. Activities are conducted in the three fields of (1) the acquisition of heat sources for heating, (2) the development of technologies for compensating for seasonal and daily load variations on gas or power, and (3) the development of control technologies to cope with emergency. In field (1), a system is developed, independent from external heat sources, to operate on an indirect heating system based on a heating furnace. In domain (2), it is proved that high efficiency system operation will be available if the influence of gas pipeline transportation parameters on load variations is analyzed for the effective utilization of the pipeline operating system. (NEDO)

FY 2000 report on the investigational study of the introduction/spread of clean energy vehicles for transportation business use; 2000 nendo chosa hokokusho. Unso jigyo yo clean energy jidosha no donyu fukyu ni kakawaru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

A comparative study of the cost effectiveness in improvement of emission gas was made between the diesel particulate filter (DPF) which is studied as measures against toxic emission gas from the vehicles already sold and the compressed natural gas (CNG) vehicle which has a large number of spread among clean energy vehicles. In the trial calculation, 18 cases were set up using measures by year against diesel car emission gas, use period and annual running distance as valuables. As a result of the study, the following conclusions were obtained. At the present time, when the vehicle price dropped approximately 40% from that at the beginning of the introduction, the cost effectiveness of CNG vehicle is larger than that of diesel car with DPF. Since the unit price of natural gas is comparatively higher than that of light oil, the longer the annual running distance is, the smaller the cost effectiveness of CNG vehicle is than that of diesel car with DPF. The durability period of DPF is considered not so long, and therefore, the longer the use period is, the larger the cost effectiveness of CNG vehicle is than that of diesel car with DPF. (NEDO)

Research and development of photovoltaic power system. Research on low temperature deposition of polycrystalline thin films; Taiyoko hatsuden system no kenkyu kaihatsu. Teion seimaku gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Sato, K [Tokyo Univ. of Agriculture and Technology, Tokyo (Japan). Faculty of Technology

1994-12-01

This paper reports the result obtained during fiscal 1994 on research on a technology of low temperature deposition of polycrystalline thin films for solar cells. This research used ITO coated glass substrates, on which CdS was accumulated to a thickness of about 100 nm by using the CBD process, and over this deposition a CuInSe2 film was formed at 300{degree}C by using the ion cluster beam (ICB) process. The manufactured solar cells with a glass/ITO/CdS/CuInSe2/Au structure had an efficiency of 2%. In manufacturing a CuGaSe2 thin film by using the ICB process, effects of acceleration voltage relative to cluster beams and ionization current were investigated. It was found that the film morphology, the result of analysis by using X-ray diffraction, and the electric conductivity are sensitive to the ionization current. From these findings, an optimum film forming condition was derived. A CuGaSe2 thin film was manufactured by using the ICB process over a Cds thin film deposited by using the CDB process. Both of the surface morphology and X-ray diffraction patterns of the film did not show a large change, indicating a possibility of manufacturing cells with a reverse structure. Effects of heat treatment on CuInSe2 monocrystals were evaluated by using ESR and FTIR. 6 figs., 1 tab.

Report on achievements in fiscal 1998. Survey on environmental effects from photovoltaic power generation systems; 1998 nendo daikibo taiyoko hatsuden system no kankyo eikyo ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Different environmental effects may be assumed when large-size photovoltaic power generation systems are installed in vast unutilized lands including deserts. Knowledge having been acquired to date has been put into order on the following subjects as the pre-survey thereon: (1) environmental characteristics of desert areas, (2) discussions on environmental effects from (a) environmental assessment viewpoints, (b) contents of the environmental assessment, and (c) environmental assessment institutions, and (3) the survey policy. In discussing the environmental characteristics, it is revealed that desert areas are neither sterile nor unused, but pasturage and agriculture have been carried out in historical and traditional ways. In discussing the environmental effects, it was recognized that surveys on primary and secondary effects on the environmental are indispensable. With regard to the institutions, there are countries who have and have not the institutions even among the OECD member states. In addition, it was known that environments in the desert areas vary greatly according to the particular areas, whereas there are possibilities of installing the facilities because the effects of the facility locations on the environment are various. Therefore, it was decided to start from the case studies in locations of different types. (NEDO)

Fiscal 1974 Sunshine Project result report. Research on solar energy utilization systems (solar heat power generation); 1974 nendo taiyo energy riyo system chosa kenkyu seika hokokusho. Taiyonetsu hatsuden

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-03-01

This report summarizes the fiscal 1974 research result on solar heat power generation. The following are promising as solar heat power plant sites in Japan: Large-scale sites such as the foot of volcanos, riverbed, railway site and road, medium-scale sites such as isolated island, saltpan site and industrial park, and small-scale sites such as factory site, factory roof floor, housing complex, warehouse and school. Based on the primary concept design of both curved reflector type and tower type 1,000kW class solar heat power plants, various requirements were clarified roughly. It was clarified that food, fiber and non-ferrous metal factories can cover 80-90% of their thermal energy requirements with high- temperature solar heat, while factories related to food and fiber can cover even nearly 100% of their electric power requirements with solar heat. Study was also made on specifications of a solar simulator as common use facility necessary for characteristic evaluation of equipment and materials for solar heat power generation systems. (NEDO)

Study of a wave power generator system using an air turbine having improved J-shaped blades; Kairyo J gatayoku kuki turbine wo mochiita haryoku hatsuden sochi no kenkyu

Energy Technology Data Exchange (ETDEWEB)

Honma, T; Omata, K; Kojima, N [Meiji University, Tokyo (Japan)

1997-11-25

An improved J-shaped blade, in which a J-shaped blade is combined with a small-size Savonius blade, has been developed, to further improve efficiency of an air turbine for wave power generator systems. A prototype model of stationary wave power generator has been developed using the improved blade, to confirm its power generation characteristics by tests in a water tank and small-scale ocean tests. The results are compared with the characteristics of the units with conventional blades. The air turbine unit with the improved blade shows an efficiency of 13 to 35%, which is higher by 10 to 20% than that of the turbine with a J-shaped blade and by 20 to 70% than that of the one with a Savonius blade, more noted at low speed of rotation. It is therefore considered that the turbine with the improved blade is suited for sea areas having a relatively low wave height. It is also considered that efficiency can be further enhanced, when one or more guide vanes are provided around the blade. 2 refs., 12 figs.

Load leveling by a battery system in an electric power system with a photovoltaic system; Taiyoko hatsuden system ga donyusareta denryoku keito no chikudenchi ni yoru fuka heijunka

Energy Technology Data Exchange (ETDEWEB)

Kenmoku, Y.; Sakakibara, T. [Toyohashi University of Technology, Aichi (Japan); Nakagawa, S. [Maizuru College of Technology, Kyoto (Japan); Kawamoto, T. [Shizuoka University, Shizuoka (Japan)

1997-11-25

Storage battery-aided load leveling system is introduced into a power system having a photovoltaic power generation (PV) system, and the effect of the introduction is examined. For this purpose, the resultant improvement on the load factor and reduction in the annual cost are evaluated. Used as the load factor in the studies are the hourly records of power transmitted and received by Chubu Electric Power Co., Inc., in 1995. The output of the PV system is calculated using weather data collected in Nagoya City in the same year. Findings as the result of the studies are stated below. The maximum power is suppressed but a little if it is only the PV system that is introduced into the system. That is, a 2GW PV system introduced into the system suppresses the maximum power only by 0.5GW or less. The maximum power is suppressed more effectively when a storage battery is added, and it decreases linearly with an increase in the storage battery capacity. As for reduction in the cost, the reducing effect is higher when the rate of storage battery capacity/introduced PV capacity is higher in the presence of an introduced PV capacity of 0.8GW or more. 2 refs., 7 figs., 3 tabs.

Dynamic programming for reduction of fuel consumption in a photovoltaic/wind/diesel generating system; Doteki keikakuho ni yoru taiyoko/furyoku/diesel hatsuden system no nenryo shohiryo no sakugen

Energy Technology Data Exchange (ETDEWEB)

Ishikawa, K.; Kenmoku, Y.; Sakakibara, T. [Toyohashi University of Technology, Aichi (Japan); Nakagawa, S. [Maizuru National College of Technology, Kyoto (Japan); Kawamoto, T. [Shizuoka University, Shizuoka (Japan)

1997-11-25

Dynamic programming is employed in the study of the operation of the diesel engine in a photovoltaic/wind-force/diesel-engine power generating system, which aims at reduction in the system fuel consumption and at determining an optimum system constitution. The parameters set in this system are the photovoltaic/wind-force supply rate, photovoltaic/wind-force power generation ratio, and battery capacity. An island in Ise Bay, with an annual load power of approximately 1.59-million kWh and mean daily load power of approximately 4336kWh is assumed as the location for the system. Observation data of Ommaezaki Weather Station are utilized for the calculation of the amount of photovoltaic/wind-force power generation. It is found as the result that the fuel consumption of the diesel engine in this system decreases to 82-84% when the natural energy supply rate is 20%. It is also found that the fuel consumption of the system records the minimum at a photovoltaic/wind-force ratio of 60/40, irrespective of the battery capacity or natural energy supply rate, and this ratio is the optimum ratio. 3 refs., 9 figs., 1 tab.

Data book on new energy technology development in FY 1997. Installations of photovoltaic (PV) power generation; Shin energy gijutsu kaihatsu kankei data shu sakusei chosa. Taiyoko hatsuden jireishu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The present survey places particular emphasis on the field of PV power generation systems, and intends to collect data on solar cell application products and PV power generation system installation cases, to classify them according to their usage and to compile a collection of case records including photographs. For the data collection, two formats have been adopted. A format for the solar cell-based products includes a picture of the product, and information on solar cell output and commercialization status. Another format for the installation of PV power systems includes a picture of the installation, and information on location, output level, system type, PV module type, owner, and date of installation. The application of solar cells was classified into 14 fields, i.e., consumer appliances, road and traffic, railroad, general industries, housing related, automobiles, agriculture, ocean development, disaster prevention and safety, amenity, developing countries, buildings, public facilities, and environment. A total of 241 valid cases have been collected. Overseas products and installation cases are often characterized by new applications and innovative design, and contain a lot of useful suggestions for promoting the spread of PV technology in Japan

Feasibility study on the demonstrative test on the hybrid mini hydroelectric power generation technology. 2; Hybrid gata mini suiryoku hatsuden gijutsu ni kakawaru jissho shiken kanosei chosa. 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

A study was made for the purpose of electrification of unelectrified zones of the mountainous areas in developing countries using extremely small hydroelectric power facilities. The target for this project is a development of a micro hydroelectric power system with a size of about 5kW, which is estimated regarding that 1 village has 80 houses and each house needs electricity of 60W. In the study, the low-head system using a weir of irrigation channels in Subang pref. of West Java state was selected by the evaluation of access, stability of flow rate, natural conditions, etc. The hydroelectric power plant is of a flow-in method in which water is taken from the left bank and is injected/discharged to the downstream of the left bank. As the hybrid complementary power source, hybrid battery with a two-hour charging time at peak and a capacity of 3.5kWh was considered. When estimating the construction cost of the hybrid micro hydroelectric power system and equalizing by durable years, the operational cost per kW is 15 times higher than the benefits which local people receive. It was judged to be difficult to say that the micro hydroelectric power system is economically feasible. It was predicted that the financial profit during the demonstrative test is good, according to a trial calculation of income from power rates and the operational cost. 18 refs., 90 figs., 53 tabs.

Fiscal 1976 Sunshine Project result report. Research on solar energy utilization systems (solar heat power generation); 1976 nendo taiyo energy riyo system chosa kenkyu seika hokokusho. Taiyonetsu hatsuden

Energy Technology Data Exchange (ETDEWEB)

NONE

1977-03-01

Research was made on solar heat power generation following last fiscal year, as a part of solar energy utilization technologies. In this fiscal year, in particular, research was made on the following: selection of suitable sites for solar heat power plants in Japan, estimation of expected power supply, positioning of a solar heat power system among future power systems, operation policy of solar heat power systems, survey on suitable sites for the 1,000kW pilot power plant, operation characteristics of the small test plant, design of the 1,000kW pilot power plant, test methods and facilities for every element equipment of solar heat power systems, an environmental test method for mostly solar collectors, and the profitability of solar heat power systems. Optimum operation temperature levels were nearly 350 degrees C for distributed systems and nearly 400 degrees C for centralized ones. The distributed system is profitable in a unit capacity range less than 5-10MWe, while the centralized system is profitable in a range over 10MWe. Under some assumptions, the power cost of solar heat power systems was estimated to be 20-30yen/kWH. (NEDO)

Research and development of system to utilize photovoltaic energy. Survey on the specific purpose modules; Taiyoko hatsuden riyo system no kenkyu kaihatsu. Taiyoto module ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the survey results on the specific purpose modules for photovoltaic power generation in fiscal 1994. (1) On the feasibility survey on new application fields, it was clarified that photovoltaic power generation is applicable to extensive areas such as farmland, road, railway and public facility as latent demand sites. (2) On the optimum modules for various specific purposes, the structure, production method, cost estimation and issues of various modules were studied for desert, wasteland, coast, ocean, river, embankment, railway, road, mobile facility and arcade. (3) On the survey on new materials and material development, various conventional materials and materials promising for required performance were surveyed for every application. (4) On the survey on technology trends, the survey members participated in the first international photovoltaic energy conversion conference and the photovoltaic power generation workshop, while the members held the 1st-5th specific purpose module subcommittees. 1 tab.

Fiscal 2000 achievement report. Development of technologies for waste treatment and recycling (Development of technologies for appropriate treatment of air bags); 2000 nendo haikibutsu recycle kanren gijutsu kaihatsu seika hokokusho. Air bag tekisei shori gijutsu no kaihatsu nado

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

A centralized treatment process respecting environmental protection and safety for unused air bags aboard disused automobiles is developed. In concrete terms, a heating facility owned by Daicel Chemical Industries, Ltd., is used, which includes an apparatus for examining exhaust gas dioxins and an exhaust gas treatment apparatus and, with this facility, studies are made for appropriately treating waste gas and waste water to be generated when air bag modules undergo centralized heating. Endeavors in fiscal 2000 center about (1) the development of waste gas treatment technologies, (2) development of waste water treatment technologies, (3) chemical analysis of waste water sludge, dusts and air bag residues, and (4) the study of appropriate treatment of non-azide air bag modules. As to the development of exhaust gas treatment technology, it was proved that the exhaust gas treatment system consisting of secondary incineration furnace, exhaust gas cooling tower and bag filter worked effectively. (NEDO)

Joint Research. Report on the results of developing commercialization of a technology of process wastes and re-utilize them by using petroleum substituting energy; Kyodo kenkyu. Sekiyu daitai energy riyo haikibutsu shori saishigenka gijutsu jitsuyoka kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

A study was conducted on a technology to melt shredder dust and non-combustible wastes directly by using coal, reduce their volume and re-utilize them. The elementary study on a high-temperature melting and treating technology set such targets as optimizing the melting and treating technology in correspondence with properties of materials to be treated, by using a small melting test plant, achieving a volume reduction rate of 1/200, and reducing treatment cost. In order to make innoxious the different kinds of environmental loading materials contained in exhaust gas from a high-temperature gasification and direct melting system, discussions were given on an optimum control condition for the exhaust gas system facilities. Furthermore, physical properties of discharges (slags nd metals) were investigated to discuss material re-utilization. In discussing optimal systems, three kinds of systems including two types utilizing fuels were proposed as high-temperature gasification and melting treatment process from a viewpoint of technology and cost. Respective systems were compared with each other on treatment cost, and their priorities were identified. 56 refs., 50 figs., 55 tabs.

Research program for environmentally-friendly coal utilization system. Follow-up project for simplified desulfurizers (Weifang Chemical Industry Works); Kankyo chowagata sekitan riyo system donyu shien jigyo. Kan`i datsuryu setsubi ni kakawaru follow up jigyo (Weifang kakosho)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

To suppress the emission of environmental pollutants from coal utilization in China and to contribute to stable security of Japan`s energy, demonstration of clean coal technology and consolidation of diffusion base to be introduced into China have been promoted. Demonstration program for diffusing simplified desulfurizers has been promoted. For accelerating the achievement, experts of desulfurizers were delegated to Weifang Chemical Industry Works, to support the program. Exhaust gas is introduced from boiler via water spray dust remover, suction fan and centralized stack into absorption tower of the simplified wet-type desulfurizer. In the ascending process, the exhaust gas contacts with absorbent, to remove SO2 and dust. The absorbent is blasted up through the spray nozzle. The absorbent is oxidized by the air into sulfate ion in the liquid chamber at the lower part of tower, and neutralized by hydrated lime to form gypsum. Through the continuous operation for two years, understandings were remarkably increased. However, good treatment of the tax system is required for further diffusion. Though there are no problems for ordinary start and stop, emergency operation is insufficient. There are some problems in the maintenance due to the delay of finding failures. 16 figs., 1 tab.

Fiscal 1998 research report. Current state survey for promoting the field test project for introduction of advanced industrial furnaces; 1998 nendo koseino kogyoro donyu field test jigyo ni okeru jigyo sokushin no tame no jittai chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Survey was made on the current state of installation and operation of industrial furnaces mainly in manufacturers to predict the applicability of advanced industrial furnaces, and study was made on energy consumption trends, the energy saving effect of advanced industrial furnaces, and factor extraction for their applicability. In the survey, questionnaires were delivered to 4,597 offices extracted from domestic 50,780 offices with employees more than 30, and nearly 30% of them were recovered, covering nearly 2.6% of all the offices concerned with this survey. As the survey result, the total annual energy consumption of domestic manufacturers was estimated to be 740,949 x 10{sup 6}Mcal, and among it, 709,709 x 10{sup 6}Mcal for large industrial furnaces. Under the assumption that nearly 30% of large industrial furnaces in operation are replaced with advanced industrial furnaces, energy saving expectation is estimated to be 210,000 x 10{sup 6}Mcal. Opinions and demands for this project showed the difficulty in their application to industrial furnaces in operation and study on their effects. Further enlightenment activities are necessary. (NEDO)

Survey for making a data book related to the development of new energy technology (the photovoltaic power generation); Shin energy gijutsu kaihatsu kankei data shu sakusei chosa (taiyoko hatsuden)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

A data book related to the photovoltaic power generation was made as a part of the systematical preparation of new energy related data. The paper arranged the importance of introducing the photovoltaic power system and the CO2 reduction effect at levels such as the government, local government, industries and individuals which are users. Described were the production quantity by region/type/company, shipment by usage, production amount and prices of solar cells. Arranged was the situation of policies on the photovoltaic power generation in Japan and developed countries. Examples of the introduction in countries including Japan were examined to know the introduction quantity and target. The paper introduced the subsidy system, preferential tax system and loan system for the introduction of the photovoltaic power system in Japan. The flow was summed up from the planning of the system introduction to the installation. The status of handling with the system introduction of government related organs and local governments was stated. The paper showed a list of the companies related to the photovoltaic power system and the references of solar cell makers and solar system installation makers. The development is so quickly made that the renewal every year of the system and the quality enhancement are required. 32 figs., 112 tabs.

Report on achievements in fiscal 1975 in Sunshine Project. Feasibility study on a volcanic electric power generation system; 1975 nendo kazan hatsuden hoshiki ni kansuru feasibility study seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1976-03-01

The survey and study activities in the second year for the feasibility study (FS) on a volcanic electric power generation system consist of the following three parts: Part I, the case study on Satsuma Iojima Island, Part II, case study on Toyohane Mine, and Part III, FS on remote measurement of volcanic fume. The Part I, which has been performed subsequently from the previous fiscal year, has carried out the following surveys at different sites: meteorological, hydrological and underground water surveys, natural earthquake survey, fume and hot spring surveys (on-shore and off-shore), heat dissipation survey, tide level survey, underground structure survey (electric exploration), natural environment (vegetation) survey, thermal image survey, and social environment survey. The part II has begun surveys starting this fiscal year, because a considerable number of high temperature portions are already known to exist in the gallery, where there is a possibility of dry and hot rocks to exist without relationship with the present volcanic activities. This fiscal year has carried out mainly putting into order and analyzing the materials having been obtained in association with mine developments. The part III has been performed succeeding the 'FS on technologies to measure volcanic fume energy' done by the Japan Mining Industry Association. Some experiments were also executed at the Aso volcano. (NEDO)

Achievement report for fiscal 1981 on Sunshine Program research and development. Development of photovoltaic power plants (Meteorological observation); 1981 nendo taiyonetsu hatsuden plant no kaihatsu seika hokokusho. Kisho kansoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-31

The effort aims to measure environmental factors for the evaluation of plant performance and equipment durability in a test operation of a Nio Solar Heat Test Plant (built on a site formed by reclaiming a salt field at Nio Town, Kagawa Prefecture). Meteorologically observed are the amount of direct solar radiation, amount of solar radiation from unobstructed sky, time of solar radiation, wind direction, wind speed, air temperature, wet-bulb temperature, amount of precipitation, and time of precipitation. Dust fall, sea salt grain, and sulfur oxides are also measured monthly. As for the direct solar radiation (DH) on the horizontal plane, it is determined by conversion of its hourly accumulation on a normal plane. The conversion method is so adjusted as to reduce errors for time belts in the morning and evening when change is great in sun elevation. The amount of sky solar radiation is calculated by subtracting DH from the amount of solar radiation from unobstructed sky. As for the time of solar radiation, it is determined by accumulating by the use of a computer the time at which pyrheliometer output is beyond a threshold of 21mW/cm{sup 2} on the pyrheliometer. A minicomputer is used to analyze and process the observed data. The annual and monthly reports and daily records are also mentioned in this achievement report. (NEDO)

Fiscal 1999 research report. Data collection for development of new energy technology (Photovoltaic power generation); 1999 nendo shin energy gijutsu kaihatsu kankei data shu sakusei chosa (taiyoko hatsuden) hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

As a part of systematic data preparations on new energy technology, this research aims at collection and analysis of data on domestic and overseas applications, diffusion targets, concrete examples, policies, laws, subsidy systems, and the latest technology development trends of photovoltaic power generation, and at preparation of its basic data through integration and systematization of the collected data. The research items are as follows: domestic and overseas applications, diffusion targets, concrete examples, policies, laws, subsidy systems, productions of solar cells, typical photovoltaic power generation costs, trial calculations of CO{sub 2} reduction in photovoltaic power generation, technology development trends, technology development issues, issues for faster diffusion, configurations and conceptual charts of photovoltaic power systems, and major domestic and overseas trends. As a supplement, domestic and overseas manufacturers of solar cells, and manufacturers of photovoltaic power systems are listed with their addresses. The solar cell production capacities of major countries are also arranged. (NEDO)

Study on an optimum ratio of PV output energy to WG output energy in PV/WG hybrid system; Taiyoko/furyoku hybrid hatsuden system no saiteki yoryohi ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Nishikawa, S [Kandenko Co. Ltd., Tokyo (Japan)

1996-10-27

A photovoltaic power (PV) and wind generated power (WG) are an unlimited clean energy source, yet their output is unstable depending on the fluctuation of weather conditions such as solar radiation and wind velocity. Consequently, a large-scale power storage equipment is necessitated leading to a high cost especially in an independent system. As a solution, a method is available in which PV and WG are combined so that the effect may be utilized for stabilizing the output of a system as a whole, at a site where a fluctuation pattern is different between photovoltaic energy and wind energy. In building a hybrid system by PV and WG, sites with such supplementary effect existing were selected from the viewpoint of stabilizing the fluctuation of the power generation in the long run; and then, an examination was made on the optimum PV capacity ratio (%Ppo) in each site. As a result, it revealed that the %Ppo had great bearing on a ratio of PV energy fluctuation to WG, which was converted to a numerical formula. A comparatively simple examination by means of meteorological data also indicated that the share ratio was possibly optimized between the quantities of PV and WG energy. 4 refs., 2 figs., 2 tabs.

On a research of the jet stream power generation. Part 2. Maximum height of a flying kite; Jet kiryu hatsuden no kenkyu. 2. Tako no totatsu kodo ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Miyashita, J. [Nihon University, Tokyo (Japan). College of Science and Technology

1998-04-05

Tethering cable was investigated as a part of a research of jet stream power generation using balloon and kite. Recently, there appeared new materials with light and high strength properties, such as carbon and polyamide resin. When these are used as tethering cables, flying ability of tethered bodies is remarkably improved. Tethered balloon at the altitude of 6500 feet and large-scale kite at the altitude of 5000 m are proposed for the idea of jet stream power generation. A computer program was developed for determining the flying ability of a kite, to calculate it. Similarity rule was also determined by the dimensional analysis. For a kite with a tethering cable having uniform diameter and specific gravity, the similarity can be obtained when two kinds of similarity rules are satisfied. One is (length of tethering cable/width of kite wing)times(dynamic pressure of air/tensile strength of cable){sup 1/2}=(constant). Another is (length of tethering cable)times(density of cable/tensile strength of cable)=(constant). Since the maximum height is in proportion to (strength/specific gravity) of the cable, it increases drastically using high performance materials. It is affected by the aerodynamic performance of the kite and the safety factor of strength of the cable. 4 refs., 45 figs., 2 tabs.

Study on wave power generation of electricity using torsion arc blade type horizontal axis wind turbine; Nejire enko yokugata suihei jiku fusha wo mochiita haryoku hatsuden ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Kojima, N; Kishimura, K [Meiji University, Tokyo (Japan)

1996-10-27

Windmilling characteristics of a combination of a torsion arc blade type (TABT) horizontal axis wind turbine and a reverse torsion arc blade type (RTABT) horizontal axis wind turbine were evaluated in a wave activated power generation experiment. The TABT wind turbine had six blades, and the front and rear parts of the blade were twisted in the same direction, which caused the direction of rotor rotation to change as the direction of wind along the shaft changed. The RTABT wind turbine had twelve blades, and the front and rear parts of the blade were twisted reverse to each other, which allowed the direction of rotor rotation to stay constant even in the presence of wind direction reversal. To keep the direction of rotor rotation unchanged in the presence of flow direction reversal along the power generating turbine shaft, a single-stage type RTABT wind turbine and a double-stage type were used, the double-stage type being a series connection of a first-stage RTABT (for blowout and suction) and second-stage TABT (for blowout only). Both single-type and double-type rotated in the same direction irrespective of the direction of air flow. The output of the double type was obtained by adding up the values obtained from the individual turbines. The double type was two to three times higher in efficiency than the single type in turbine revolution and power output. 2 refs., 13 figs.

Report on achievements in fiscal 1975 in Sunshine Project. Feasibility study on a volcanic electric power generation system; 1975 nendo kazan hatsuden hoshiki ni kansuru feasibility study seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1976-03-01

The survey and study activities in the second year for the feasibility study (FS) on a volcanic electric power generation system consist of the following three parts: Part I, the case study on Satsuma Iojima Island, Part II, case study on Toyohane Mine, and Part III, FS on remote measurement of volcanic fume. The Part I, which has been performed subsequently from the previous fiscal year, has carried out the following surveys at different sites: meteorological, hydrological and underground water surveys, natural earthquake survey, fume and hot spring surveys (on-shore and off-shore), heat dissipation survey, tide level survey, underground structure survey (electric exploration), natural environment (vegetation) survey, thermal image survey, and social environment survey. The part II has begun surveys starting this fiscal year, because a considerable number of high temperature portions are already known to exist in the gallery, where there is a possibility of dry and hot rocks to exist without relationship with the present volcanic activities. This fiscal year has carried out mainly putting into order and analyzing the materials having been obtained in association with mine developments. The part III has been performed succeeding the 'FS on technologies to measure volcanic fume energy' done by the Japan Mining Industry Association. Some experiments were also executed at the Aso volcano. (NEDO)

FY1995 study of highly efficient power generation system based on chemical-looping combustion; 1995 nendo chemical loop nenshoho ni yoru kokoritsu hatsuden system no kaihatsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Synthesis of highly efficient and low emission power generation plant with chemical-looping combustion using various fuels such as natural gas, coal gas and hydrogen. Development of new looping materials with suitable reactivity, regenerative ability, and avoidance of carbon deposition. To obtain the design data for demo-plant by using the current experiment high- pressure fixed bed reactor. From the viewpoint of application of the proposed power generation system with chemical-looping combustion, the following main results were obtained. 1. New looping materials: NiO/NiAl{sub 2}O{sub 4}, CoO-NiO/YSZ, and Co{sub 3}O{sub 4}/CoAl{sub 2}O{sub 4}. These materials have high reactivity, repeatability, and avoidance of carbon deposition which play important roles in application of this new combustor. 2. NO{sub x} formation can be completely avoided; both fuel NO{sub x} in reduction reactor for coal gas as fuel and thermal NO{sub x} in oxidation reactor. 3. It is identified from the experiment using fixed bed reactor with the elevated pressure that NiO/NiAl{sub 2}O{sub 4} is a suitable material for coal gas or hydrogen. These promising results have provided valuable data for industrial application. (NEDO)

FY 2000 report on the results of the model project on facilities for the effective utilization of industrial waste from industrial complex. Separate Volume 3; 2000 nendo Kogyo danchi sangyo haikibutsu yuko riyo setsubi model jigyo. Dai 3 Bunsatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

For the purpose of promoting the effective utilization of industrial waste as petroleum substitution energy resource and reducing the consumption of fossil fuels in Thailand, a model project on facilities for the effective utilization of industrial waste from industrial complex was worked on, and the FY 2000 results were reported. In Separate Volume 3, drawings of the following were included: furnace, free board spray nozzle, dispersion air nozzle, secondary burner, sand make-up conveyor, sand discharge gate, boiler, silencer for boiler safety valve, steam header, steam accumulator, gas cooling tower, refuse drainage storage tank, small sized drainage pump, pressure tank, flue gas duct, air damper, incombustible conveyor 2, sand circulation system bag filter, weighing bridge, fan starter panel, control panel, control panel, local switch box, distributed control system, field instrument, flue gas analyzer. (NEDO)

FY 2000 Feasibility study on the environmentally-friendly coal utilization systems as part of the international project for coal utilization measures. Feasibility study on supporting introduction of the environmentally-friendly coal utilization systems in Vietnam (Model project for introduction of advanced coal preparation systems); 2000 nendo kokusai sekitan riyo taisaku jigyo chosa hokokusho. Kankyo chowagata sekitan riyo system kanosei chosa jigyo Vietnam ni okeru kankyo chowagata sekitan riyo system donyu shien jigyo (kodo sentan system donyu model jigyo kanosei chosa jigyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-06-01

The feasibility study was conducted on a model project in Vietnam, aimed at solving the environmental pollution problems resulting from use of coal by demonstrating and disseminating the Japan's environmental technologies in the Southeast Asian countries. The feasibility study was conducted for the Cua Ong Coal Preparation Enterprise, which has the largest coal preparation capacity in Vietnam and port facilities. It is treating raw coal from 10 coal mines for classification and preparation, and shipping coal of various types that meet the standards for domestic use and export. The survey results point out that unrecovered coal remains in waste water discharged from the coal preparation plants to pollute the sea area, and that quantity of the refuse increases because of the unrecovered coal it contains. The environmental technologies needed to introduce include modification to variable wave pattern type jigging separator, refuse height measuring instrument and automatic controller, circulating heavy medium gravimeter, highly functional settling pond, and flocculent facilities. (NEDO)

FY 2000 report on the results of the development of technology for commercialization of the photovoltaic power system - R and D of evaluation technology of the photovoltaic power system. R and D of the system evaluation technology; 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu - System hyoka gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Based on the evaluation method for the performance prediction system of the standard photovoltaic power system, the R and D were conducted of the system generation output prediction technology which is general-purpose, simplified and applicable to various kinds of photovoltaic power system for residential use, and the FY 2000 results were summed up. In this fiscal year, the photovoltaic power system for residential use was increasingly installed at 15 places, and 100 sites in total were made database and analyzed. As to the development of simulation technology, technology of calculation was established such as the simulation of multi-plane array composition and correction of multi-plane array incidence. Further, technical information on system trouble and knowledge/information/proposal for reducing power generation loss were arranged by design parameter. Using the data on solar radiation/power loss at sites of residential use photovoltaic power systems installed in the Kanto area, value analysis of the capacity of wide area facilities of the photovoltaic power system was made by the statistical method. This study was compiled into the revised edition of design manual. (NEDO)

FY 1998 Report on development of technologies for commercialization of photovoltaic power systems. International co-operative project (IEA implementing agreement for a co-operative programme on photovoltaic power systems, 11th and 12th executive committee meetings); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu kokusai kyoryoku jigyo. IEA taiyoko hatsuden system kenkyu kyoryoku program jisshi kyotei dai 12 kai dai 11 kai shikko iinkai

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Described herein are outline of the International Energy Agency/Co-operative programme on Photovoltaic Power Systems (IEA/PVPS), and minutes of the 11th and 12th executive committee meetings. Japan signed the IEA Implementing Agreement for a co-operative programme on Photovoltaic Power Systems in April 1993, and has been participating in the programme for research and development, demonstration, analysis, information exchange and introduction promotion, among others. Presented to the 11th executive committee meeting are progresses in each task, review of the PVPS programme by an independent reviewer, strategy for the next term of the PVPS agreement, and marketing of PV in the IEA member countries. The meeting also has confirmed the action plans and partial responsibilities. In the 12th executive committee meeting, the progresses of the tasks, e.g., objects, activities and problems, are reported, and reviewed by the participants. Discussed in the task 1, information exchange, are new communication methods, publication frequency and contents of Internal Survey Report, and opening of the internet home page, among others. (NEDO)

Research report for fiscal 1995 on analysis and evaluation of demonstration tests for establishment of residential photovoltaic power generation load leveling technology, of which evaluation on weatherability of devices used in residential photovoltaic power generation system; 1995 nendo kenkyu hokokusho. Jutaku you taiyoko hatsuden fuka heijunka gijutsu tou kakuritsu jissho shiken ni kansuru kaiseki hyoka no uchi jutaku you taiyoko hatsuden system kiki no taikosei hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Weatherability tests have been performed on devices used in the residential photovoltaic power generation system by means of exposure, with the objectives to analyze and evaluate the safety and reliability due to aging of the devices used in the residential photovoltaic power generation system. This paper summarizes the achievements in fiscal 1995. In the outdoor exposure test on solar cell modules, multi-crystalline silicon solar cell modules were selected as the test specimens, and thermo-couples were embedded in the modules to measure the temperatures. Also for the purpose of comparison, storage test specimens were stored in a constant temperature and humidity chamber. The exposure tests were carried out in three locations of the city of Choshi in Chiba Prefecture, the Miyako Island test site in Okinawa Prefecture, and the Miyako Island seashore. In the measurement and evaluation, appearance observation and measurements of output characteristics and insulation resistance were executed in summer and winter. No noticeable changes were observed in the measurements after lapse of four months and six months. In the outdoor exposure tests of metal test pieces, aluminum alloys were tested for corrosion caused by contact with different kinds of metals. Although the test period was short in the current fiscal year, difference in corrosion degrees in the aluminum alloys was found already in three months. (NEDO)

Research report for fiscal 1996 on analysis and evaluation of demonstration tests for establishment of residential photovoltaic power generation load leveling technology, of which evaluation on weatherability of devices used in residential photovoltaic power generation system; 1996 nendo kenkyu hokokusho. Jutaku you taiyoko hatsuden fuka heijunka gijutsu tou kakuritsu jissho shiken ni kansuru kaiseki hyoka no uchi jutaku you taiyoko hatsuden system kiki no taikosei hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Weatherability tests have been performed on devices used in the residential photovoltaic power generation system by means of exposure, with the objectives to analyze and evaluate the safety and reliability due to aging of the devices used in the residential photovoltaic power generation system. This paper summarizes the achievements in fiscal 1996. In the outdoor exposure tests on solar cell modules, results of the tests were derived for up to 18 months after the start of the exposure at Choshi City, Miyako Island and the Miyako Island seashore. In the appearance observation, some white rust has appeared in the contact section of the aluminum frames of the solar cell modules and fixing screws, which have been exposed at Miyako Island and the Miyako Island seashore, but no changes that may give influence on the performance of the solar cells have been observed. The results showed performance similar to or slightly inferior to that before the exposure as a whole. The insulation resistances were all found good. According to the result of the outdoor exposure test of metal test pieces, noticeable difference in the corrosion degrees was recognized in the contact corrosion section of the aluminum alloys exposed in three areas having different meteorological and environmental factors. Electroplated zinc was found to have severer pitting corrosion in the contact sections than treatment-free zinc. (NEDO)

Research report for fiscal 1997 on analysis and evaluation of demonstration tests for establishment of residential photovoltaic power generation load leveling technology, of which evaluation on weatherability of devices used in residential photovoltaic power generation system; 1997 nendo kenkyu hokokusho. Jutaku you taiyoko hatsuden fuka heijunka gijutsu tou kakuritsu jissho shiken ni kansuru kaiseki hyoka no uchi jutaku you taiyoko hatsuden system kiki no taikosei hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

With the objectives to analyze and evaluate the safety and reliability due to aging of the devices used in the residential photovoltaic power generation system, weatherability tests have been performed on devices used in the residential photovoltaic power generation system by means of exposure. This paper summarizes the achievements in fiscal 1997. In the outdoor exposure tests on multi-crystalline silicon solar cell modules at Choshi City, Miyako Island and the Miyako Island seashore, the output characteristics after the exposure tests showed a result that the insolation intensity and the change in the short circuit current are approximately proportional, and the temperature in the module and the change in the open voltage are inversely proportional. The module characteristics retention rate showed no change in the 29-month exposure at all of the three exposure locations. The insulation resistance in the exposure test specimens have been good at 2,000 M{omega} or more in all the locations until 18 months have elapsed. However, the test specimens in Miyako Island and the Miyako Island seashore showed 99 M{omega} after 23 months, and 129 to 1,774 M{omega} after 29 months. According to the outdoor exposure tests of metal test pieces, noticeable difference was found in corrosion due to difference in the environment by each exposure location, whose order of the corrosion degree was the Miyako Island seashore > Miyako Island > Choshi City. (NEDO)

Report on achievements in fiscal 1998. Development of technologies to put photovoltaic power generation systems into practical use - Research and development of solar beam power generation and utilization systems and ancillary technologies (Investigations and researches on large-size energy supply system); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (ogata energy kyokyu system no chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

With an objective to propose large-size system development scenarios assuming installations in deserts, the following investigations have been carried out: (1) collection of data on societies, economy, and energies in China and other countries where the large systems are assumed to be installed, (2) in order to reduce the costs, comparison was given on power generation cost by using a fixed tracking frame, a single axial tracking frame, and a biaxial tracking frame, (3) in order to evaluate the life cycle, discussions were given on the required energy inputs for system equipment, transmission and transformer equipment, and the installation construction to estimate the energy payback time (EPT) and CO2 emission unit requirement, and (4) discussions on development scenarios. In Item (1), while China expects on natural gas and atomic energy as the supply source, 80% of the energy would be supplied from coal in 2010. The development of new energies in India would further be delayed than in China. In item (2), the trially calculated power generation costs in Mongol by using the fixed frame, single axial tracking frame, and biaxial tracking frame were 8.72, 8.23 and 6.94 yen per watt. In Item (3) The EPT was two years or less in a 100-MW system, and the CO2 emission unit requirements in the silicon systems were 10 to 19 kg-C/kWh. (NEDO)

Fiscal 1997 report on the results of the New Sunshine Project subsidiary operation. Development of the geothermal water use power plant, etc. (development of the binary cycle power plant / development of the geothermal well MWD system); 1997 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu (binary cycle hatsuden plant no kaihatsu (chinetsusei kussakuji kotei joho kenchi system no kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

For the purpose of improving efficiency and accuracy in geothermal well drilling, the development was conducted of an MWD (measuring while drilling) which detects borehole information in real time. In fiscal 1997, the following R and D were carried out. As to the downhole equipment, the actual well experiment on the sonde was conducted to confirm the basic performance. The design improvement, trial fabrication and experiment were conducted on mud pulse generating valve driving control equipment, bore hole signal processing unit and temperature correction circuit portion in the sonde. Concerning electronic parts, a heat resistance confirming test was conducted for data collection/assessment. Further, jigs were fabricated for tests to confirm working of each equipment. Relating to the ground equipment, conducted were improvement of the decoded program and betterment of the analytical system and interface. As to the development of the analytical system, data on depth were added to the azimuth/inclination obtained from MWD, which enabled indication of a well drilling tracing chart while drilling. 92 figs., 43 tabs.

Achievement report for fiscal 1981 on New Energy and Industrial Technology Development Organization-entrusted projects on the development of photovoltaic power system practical application technologies. Research and development of a photovoltaic power demonstration system (Research and development of private house systems); 1981 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden demonstration system no kenkyu kaihatsu (kojin jutakuyo system no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Private house systems are investigated for system constitution, detailed design is drawn, and a model house is built. For system control and protection, the power conversion unit is provided with a control which functions to constantly maximize the output. The power conversion unit without an internal oscillator is equipped with another control which functions to output single-phase AC power coincident with the commercial system in voltage and frequency when it is interconnected with the system. The power conversion unit is so designed that it is automatically stopped for the prevention of reverse voltage imposition on the commercial system in case of interruption in the commercial system. In the study of roof panel type solar cells, real-size panels are designed and fabricated, capable of a total of 3kWp. In the study of element devices, a real-size conversion unit is experimentally built and tested in combination with a rectifier and solar cells, and it is found that the unit functions as expected. A model house is designed incorporating the results of the above-said research, and is built in the precinct of a laboratory of the Fuji Electric Co., Ltd. (NEDO)

Report on achievements in fiscal 1998. Development of technologies to put photovoltaic power generation systems into practical use - Research and development of solar beam power generation and utilization systems and ancillary technologies (Development of ancillary devices for AC modules); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (AC module yo shuhen sochi no kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Reasonability evaluation was progressed on the fundamental technologies having been proposed in fiscal 1998, and development was made on elementary technologies required for system structuring. The proposals made in fiscal 1998 include the deepening of the evaluations on effectiveness of AC modules, long-term stability evaluation on the system control schemes, trial fabrication and evaluation on AC battery modules, and development and installation of 2-kW demonstration facilities. In the effectiveness evaluation, discussions were given not only on advantages, but also on disadvantages. As the advantageous point, theoretical analyses were progressed on the effect of reducing the output drop due to shading, which was made clear by providing values. Effects of increase in switching units on electric wave interference as a disadvantage were made clear. As a form that can be applied consistently from an independent power source to a system coordination system, a flexible system using the module system comprising of AC modules and AC batteries was proposed as an effective utilization measure. A proposal was also made on an autonomous discrete type system control scheme as a control system that has sufficient expandability, and is durable against disasters. (NEDO)

FY 1998 Report on development of technologies for commercialization of photovoltaic power systems. International co-operative project (IEA implementing agreement for a co-operative programme on photovoltaic power systems, 9th and 10th executive committee meetings); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu kokusai kyoryoku jigyo. IEA taiyoko hatsuden system kenkyu kyoryoku program jisshi kyotei dai 10 kai dai 9 kai iinkai

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Described herein are outline of the International Energy Agency/Co-operative programme on Photovoltaic Power Systems (IEA/PVPS), and minutes of the 9th and 10th executive committee meetings. Japan signed the IEA Implementing Agreement for a co-operative programme on Photovoltaic Power Systems in April 1993, and has been participating in the programme for research and development, demonstration, analysis, information exchange and introduction promotion, among others. The tasks are composed of exchange and dissemination of information on PVPS, operational performance and design of PVPS, use of PVPS in stand alone and island applications, grid interconnection of building integrated and other dispersed PVPS, design and grid interconnection of dispersed PVPS, e.g., roof type, design and operation of modular PV plants for large scale power generation, PV in the built environment, and feasibility study on large scale PV power generation utilizing desert areas. The 9th and 10th executive committee meetings include the co-operative programme progress reports and technical tours. (NEDO)

FY 2000 research cooperation project on the research cooperation for the commercialization of the regional adaptation type photovoltaic power generation system, etc. Research cooperation for the commercialization of the methane fermentation gas fuel cell power generation system; 2000 nendo kenkyu kyoryoku jigyo. Chiiki tekigogata taiyoko hatsuden system to no jitsuyoka ni kansuru kenkyu kyoryoku (Metan hakko gas nenryo denchi hatsuden system no jitsuyoka ni kansuru kenkyu kyoryoku)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research cooperation for the commercialization of methane fermentation gas fuel cell power generation system was made in a stock farm in Guangzhou city, China, and the FY 2000 results were summed up. In the project, the methane fermentation gas is recovered from animal faces, and a power generation system by fuel cell using the gas as fuel is constructed, and at the same time the waste is made compost and used as manure. In this fiscal year, the starting ceremony was made at the stock farm in Guangzhou city in June, and the main body of fuel cells was carried in and assembled. The trial operation of the system was successfully made in March 2001. At the same time, survey of the waste water from the farm and methane fermentation was made with accuracy. Survey was further made of the actual state of the recent energy supply/demand and the present situation of renewable energy as measures taken for non-electrification areas and environmental problems. As a result, the importance of further cooperation with the China side was emphasized in terms of the securing of animals/faces, optimum methane fermentation/recovery from animal faces, optimization of electric power of the area and environmental response, etc. (NEDO)

Survey report for fiscal 1999. Evaluation and analysis on items applied for in high-performance industrial furnace introduction field test project in fiscal 1999; 1999 nendo koseino kogyoro donyu field test jigyo chosa hokokusho. Obo anken hyoka bunseki

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This paper describes comprehensive evaluation and analysis mainly on the 51 items adopted in the high-performance industrial furnace introduction field tests. The development of a high-performance industrial furnace has completed the fundamental development research in fiscal 1998, and the possibility was verified on energy saving of more than 30% and reduction of NOx emission by 50% over that by conventional furnaces. Upon this fundamental achievement, the field test project has started as the comprehensive approach to developing the practically usable technologies for three years from fiscal 1998 until fiscal 2000, which is being promoted as a joint research project. According to the survey on the actual state in fiscal 1998, a little less than 20,000 industrial furnaces having combustion capacity of more than 500,000 Kcal/hr (excepting boilers) are being used. If these furnaces are converted into the high-performance industrial furnace, energy conservation of 210,000 x 10{sup 6} Mcal (converted to crude oil of 22.7 x 10{sup 6} kl/year) can be achieved from the maximum annual energy consumption of 700,000 x 10{sup 6} Mcal (converted to crude oil of 75.7 x 10{sup 6} kl/year). This conservation amount corresponds to about 12% of the final energy consumption in the whole Japanese industrial departments in fiscal 1996. It is expected that the performance of the full-size high-performance industrial furnace will be verified, and this technology will be promoted for wide proliferation. (NEDO)

Fiscal 1995 survey report on the environmentally friendly type coal utilization system introduction support project. Verification project on the circulating fluidized bed boiler; Kankyo chowagata sekitan riyo system donyu shien jigyo. Junkan ryudosho boiler ni kakawaru jissho jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-12-01

In relation to the circulating fluidized bed boiler which reduces the amount of sulfur oxides emitted in coal utilization, a verification project was carried out on installation of the equipment and spread activity in China and the Philippines contributing to the control of environmental pollutant associated with coal utilization and the effective use of energy. At the Fanshan area, installed was a 10t/h internal circulating fluidized bed boiler. At the performance test, coal includes around 7% of impurities such as stone, and the impurities should be excluded continuously at the time of actual run. Therefore, the boiler efficiency had to be changed from 89.5% to 85.8%. Further, power generation facilities have not yet been finished, and the overall operation of boiler turbine has not been executed. At the Zibo area, a 30t/h external circulating fluidized bed boiler was installed. The boiler efficiency reached 86.1%, over the targeted value. At the Batangas area in the Philippines, a 10t/h internal circulating fluidized bed boiler was installed. The boiler efficiency reached 85.8%, over the designed value. About the coal produced in the Philippines, slagging was feared, but the combustion state was favorable. 82 figs., 21 tabs.

Report on FS survey for project of introduction of highly energy-efficient trolley buses into the Mexico Metropolitan Area in FY 1997; 1997 nendo chosa hokokusho (Mexico city eno sho energy gata trolley bus donyu project FS chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Traffic jam and air pollution by automobiles are currently getting severe in the Mexico Metropolitan Area. Trolley buses were introduced for improving the environment more than ten years ago. Vehicles become too old for use, and their energy efficiency is low. In this project, 200 highly energy-efficient trolley buses are introduced to replace old inefficient trolley buses, which results in the improved traffic convenience in the City and enhanced energy efficiency. The new energy-efficient trolley buses are made of energy-efficient control VVVF inverters produced and exported by MELCO (Mitsubishi Electric Corporation), energy-efficient motors by MELMEX (Mitsubishi Electric Corporation, Mexico), and bodies by MASA which is a major manufacturer of bus bodies. The objective of this research is to analyze the background of introduction of new energy-efficient trolley buses and the effects of the present project. The results of analysis are going to be utilized for future promotion of the Joint Implementation and Clean Development Mechanism. 30 refs., 30 figs., 24 tabs.

NEDO Forum 2001. Session on New Energy/Energy Conservation Popularization Project (Let's walk and save energy - Let new energy run on its course); NEDO Forum 2001. Shinene shoene donyu fukyu jigyo session (aruko shoene hashiro shinene)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-09-20

The presentations made at the above-named session of the NEDO (New Energy and Industrial Technology Development Organization) forum held in Tokyo on September 20, 2001, are collected in this report. Professor Kashiwagi of Tokyo University of Agriculture and Technology in his keynote address, entitled 'How the popularization of new energy and energy conservation should be in the future,' discussed energy conservation measures, new energy measures, fuel conversion, natural gas, and atomic energy, and disclosed his long-term outlook of energy supply and demand. NEDO in its achievement report mentioned a simulation on the smooth interconnection of distributed power sources such as wind power sites to a commercial power system. It reported also that, under its 3-year high performance industrial furnace field test project started in 1998, 167 furnaces, including heating furnaces, ladles, heat treatment furnaces, melting furnaces, and gas treatment furnaces were converted into high performance industrial furnaces capable of high temperature preheated air combustion near 1000 degrees C and that the conversion brought about a great reduction in energy consumption and in carbon dioxide gas and nitrogen gas emissions. (NEDO)

Report of a photovoltaic power generation field test at Deigo-en, an old people`s home, in Ginoza village, Okinawa prefecture; Deigoen taiyoko hatsuden field test jigyo (Okinawaken Ginozamura) hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-07-26

A photovoltaic power generation system was installed on the roof of Deigo-en, a special nursing home for the aged, to collect various operation data through a long-term operation. This photovoltaic power generation system has an output of 99 kW, batteries, and functions of inverse power flow and self-operation. The solar cell module is the polycrystal system, its conversion efficiency is 12.6%, and the maximum output is 108.2 W. The array configuration is composed of 2 sets of 9 series and 51 parallels, and totally 918 modules are used. This system supplies the power for lighting and air conditioning, which are indispensable for living of 105 old-age dwellers in the home, as well as for refrigerator for storing foods, and medical equipment for maintaining their health. At the outage caused by typhoon, other disasters, or emergency, crisis management is conducted using the batteries and self-operation function, which enables to supply energy with a function of an evacuation place. Arrangement and analysis of the long-term operation data and trouble examples are to be carried out. 13 figs.

Sunshine Program for fiscal 1981. Development of practical application technologies for photovoltaic power systems (Management of research and development); 1981 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Kenkyu kaihatsu kanri

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

To gain a helpful guide toward the next process by properly evaluating the current project, evaluation of cost and inputted energy is indispensable. In fiscal 1981, as the first step of such evaluation effort, a manufacturing process model is built based on data about designing and manufacturing, and is subjected to analysis. Cost forming factors are extracted from the respective processes, and their relations are analyzed. Parameters are analyzed for the survey of energy that a system demands for operation. Test facilities now under construction are also subjected to a cost analysis. A system design document is prepared for cost analysis and for assisting the process improvement and evaluation work. For the establishment of low-cost mass-production technologies, it is necessary to reappraise the currently-employed technologies for all the processes. It is necessary to coordinate the basic processes in terms of dimension and efficiency to enable them to function as a continuous, consistent production process. Target values are set for the respective processes for an output of 500kW/year at a cell conversion efficiency of 9%. In selecting items to be specified and values to be attained, users' requests are fully considered. Details are prudently coordinated of conditions for delivery from a process to another. (NEDO)

Sunshine Program for fiscal 1981. Development of practical application technologies for photovoltaic power systems (Management of research and development); 1981 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Kenkyu kaihatsu kanri

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

To gain a helpful guide toward the next process by properly evaluating the current project, evaluation of cost and inputted energy is indispensable. In fiscal 1981, as the first step of such evaluation effort, a manufacturing process model is built based on data about designing and manufacturing, and is subjected to analysis. Cost forming factors are extracted from the respective processes, and their relations are analyzed. Parameters are analyzed for the survey of energy that a system demands for operation. Test facilities now under construction are also subjected to a cost analysis. A system design document is prepared for cost analysis and for assisting the process improvement and evaluation work. For the establishment of low-cost mass-production technologies, it is necessary to reappraise the currently-employed technologies for all the processes. It is necessary to coordinate the basic processes in terms of dimension and efficiency to enable them to function as a continuous, consistent production process. Target values are set for the respective processes for an output of 500kW/year at a cell conversion efficiency of 9%. In selecting items to be specified and values to be attained, users' requests are fully considered. Details are prudently coordinated of conditions for delivery from a process to another. (NEDO)

Report on a fiscal 1995 basic survey of the environmental engineering. Investigational survey on the improvement of the waste treatment system; 1995 nendo kankyo business no engineering ka kiso chosa hokokusho. Haikibutsu shori system no kodoka ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-05-01

The paper described the present situation of the waste treatment system for the environmental engineering and the problems. The final waste treatment plants are in the tighter and tighter condition, and therefore the waste treatment system ought to be changed to a system in which importance is placed on the size reduction, weight reduction, and recycle. Accordingly, the waste treatment system becomes more characterized as a resource feedback process, and should be given more credit as a system for production of secondary resource. The problem is arrangement of conditions of technology, cost and legislation system for smoothing such recycling flow. Of course, it is natural that the most important subject of the system is to secure the environmental preservation by the waste treatment. As future subjects, needed are understanding of the waste treatment as a resource reproductive system, relation with other industries, and review of the legislation system. In consideration of technology, cost and environmental loads, required are proposal of validity of the recycle level limit and a future image of the system structure, and policies for promoting and supporting the recycle business. 47 figs., 104 tabs.

Development of hydroponic system using agriculture waste. 1. Characteristics of rice husk charcoal as growth medium and vegetable growth; Suiko saibai ni okeru haikibutsu riyo gijutsu no kaihatsu. 1. Momigara kutan no baichi to shite no tokucho to yasai no seiiku

Energy Technology Data Exchange (ETDEWEB)

Terazoe, H; Nakaya, K; Okano, T [Central Research Institute of Electric Power Industry, Tokyo (Japan)

1994-06-01

Experimental researches were made on rice husk charcoals processed to be used as culture media for hydroponics. Rice husk charcoals with a size of 1 mm or larger retaining the original shape of the rice husk, and with a size of smaller than 1 mm were made for use in the experiment. In the culture media made of these rice husk charcoals, the charcoal with a particle size greater than 1 mm had more air portion than water portion at 6 cm above the water level, and the charcoal with a particle size smaller than 1 mm had poor air permeability. According to the result of immersing the rice husk charcoal in a culture solution, phosphoric acid ion and manganese in the solution decreased by about 35% and calcium by about 10% in the duration of 120 minutes, as a result of having been adsorbed into the rice husk charcoal. On the other hand, chloride ion increased by about 80% and potassium and iron by about 30%, because of having been dissolved out from the charcoal. In cultivating spinach, butterhead lettuce and radish in the rice husk charcoal culture media, the culture medium with charcoal smaller than 1 mm resulted in harvest reduced by about 75% in spinach, and about 10% in butterhead lettuce. 15 refs., 13 figs., 11 tabs.

Fiscal 1999 report on basic research for promotion of joint implementation programs. Basic research on introduction of energy saving facilities into Bulgaria's Kremikovtzi Steelworks; 1999 nendo Bulgaria Kremikovtzi seitetsusho no sho energy setsubi donyu kiso chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The plant undergoes a survey for higher energy efficiency, pursuant to the COP3 (Third Session of the Conference of the Parties to the United Nations Framework Convention on Climate Change) protocol. Dry quenching and coal moisture control are investigated for the coke oven; exhaust heat recovery and high efficiency ignition burner for the sintering machine; top pressure recovery power generation and hot stove exhaust heat recovery for blast furnace; gas recovery for the converter; scrap preheating for the electric furnace; continuous casting and soaking pit efficiency improvement for the blooming process; hot charge and heating furnace efficiency improvement for the hot strip mill reheating furnace; and furnace efficiency improvement and hydrogen annealing applicability for the annealing furnace. The energy saving effects of the above are calculated under conditions that one more of the same be added to the continuous slab casting unit and that a continuous bloom casting unit be constructed for the continuous casting of the whole, and that hydrogen annealing be adopted. A reduction of 141,900toe/year is to be achieved, which occupies 6% of the energy consumption of the whole steelworks. A greenhouse gas reduction of 333,600t-CO2/year is feasible. Now that privatization is under way for business reconstruction and rationalization, suggestions will be presented in consideration of the order of priority of investment recovery effects with attention paid to the privation program. (NEDO)

FY 1994 Report on the results of the joint research project for optimum introduction of development of fuel cell technologies for urban energy centers; 1994 nendo toshi energy center nado nenryo denchi gijutsu kaihatsu saiteki donyu chosa seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-05-01

Described herein are the FY 1994 results of the joint research project for optimum introduction of development of fuel cell technologies for urban energy centers or the like. The necessary economic conditions for introduction of a fuel cell system to be competitive with the conventional system which individually supplies electric power and heat are 250,000 yen/kW as the construction unit cost, 0.10m{sup 2}/kW as the installation area, 5 years as the cell body life, use of an inexpensive fuel gas (2 to 6 yen/Mcal). Moreover, it is an indoor system which shall have the operational characteristics to follow daily demand fluctuations while operating under the optimum conditions in the urban redevelopment area considered. A 5,000kW-class fuel cell plant burning fuel gas (2 yen/Mcal) will need a total floor area of approximately 400,000 m{sup 2} in an energy-intensive office type demand area. These conditions shall be met in order to economically introduce the 5,000kW-class plant. It is also necessary to compare the plant with the competitive cogeneration plants. The specifications for the prototype now under consideration are sufficient for the energy-saving effect, and it is premised that these specifications and characteristics are secured. (NEDO)

Reports on 1979 result of Sunshine Project. Investigation and research on solar energy utilization system (solar thermal power generation system); 1979 nendo taiyo energy riyo system chosa kenkyu. Taiyoko hatsuden system

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-03-01

In connection with the practicability of a solar thermal power generation system, examination was made on the technical economic problems and the operation method as well as on the problems of required performance of the constituent equipment, with the measuring method and performance evaluation method examined that are suitable for various devices. The items for the examination are as follows: (1) Silicon as the raw material for solar cells and its R and D, (2) Amorphous silicon solar cells, (3) R and D on low cost solar cells and array, (4) Basic design for photovoltaic generation system, and (5) Problems and technical subjects for solar cell standard measurement. The research themes and items for the above examination are listed as below: (1) Demand trend for raw material silicon, overseas trend, and development plan for polycrystalline silicon; (2) R and D plan for amorphous Si solar cell and its system, their optimum design, and their cost analysis and economic effect; (3) Technological investigation on cells and examination on array; (4) Basic design, peripheral equipment for system, and development schedule; (5) Report on the first actual state investigation concerning instrumentation of solar cells, i.e., on 'instrumentation and deviation in transformation efficiency', calibration system, problems of instrumentation of new device, problems of reliability test method, situation in various countries, and trend in atmospheric turbidimeter. (NEDO)

Survey for making a data book related to the development of new energy technology. Wind power generation; 1999 nendo shin energy gijjtsu kaihatsu kankei data shu sakusei chosa hokokusho. Furyoku hatsuden

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of systematically arranging the data on new energy, this paper focused on the wind power system and collected/arranged the most up-to-date published data on the wind power system, mostly in terms of samples of introduction in Japan and abroad, supporting plans and policies, market of the wind power system, specifications for the main wind turbines, etc. This report included the following: (1) Quantity of introduction of wind power system. (2) Targeted quantity of introduction of wind power system in Japan and abroad. (3) Policies on wind power system in Japan and abroad. (4) Sales of wind power system. (5) Cost of introduction of wind power system. (6) Effects of introduction of wind power generation. (7) Trend of technology development/subjects on technology development/problems on introductory promotion. (8) Outline of wind power system. (9) Predominant trends of wind power generation in Japan. (10) List of the persons to contact enterprises related to wind power generation. (11) Quantity of wind energy existing in Japan. (12) Specifications for wind turbine by power generation scale. (13) Method to calculate power generation cost of wind power system. (14) Explanation of basic technical terms. (15) List of the related rules as to introduction of wind power generation. (16) Publications relating to wind power generation. (NEDO)

Simulation of PV/FC power hybrid system. Change of system capacity with load form factor; Taiyoko hatsuden nenryo denchi hybrid system no simulation. Fuka keijoritsu ni yoru system yoryo no henka

Energy Technology Data Exchange (ETDEWEB)

Sekiguchi, N.; Tani, T. [Science University of Tokyo, Tokyo (Japan)

1997-11-25

Study is conducted of a photovoltaic/fuel-cell hybrid system whose power storage is a hydrogen storage that uses a hydrogen absorbing alloy. In a simulation in this research, the solar cell conversion efficiency is changed from 15.0% to 21.0% and the fuel cell power conversion efficiency from 40.0% to 50.0%, and the resultant changes in the capacity and operation rate are investigated for each of the devices in the system. The findings follow. A 1.0% change in the solar cell conversion efficiency results in a 4.8kW change in the solar cell capacity and a 1.6-ton change in the hydrogen storage capacity. With a 1.0% change in the fuel cell power conversion efficiency, there is a 14.7kW change in the solar cell capacity and a 5.3-ton change in the hydrogen storage capacity. The fuel cell capacity is not dependent on the solar cell conversion efficiency or fuel cell power conversion efficiency but on the maximum load in each of the load form factors. The rate of occurrence of an operation rate of less than 30% is 54.7% both in DC/DC converter and hydrogen generator, 24.6% in fuel cells, and 16.7% in the DC/DC inverter. 7 refs., 7 figs., 1 tab.

Reports on 1979 result of Sunshine Project. Investigation and research on solar energy utilization system (solar thermal power generation system); 1979 nendo taiyo energy riyo system chosa kenkyu. Taiyoko hatsuden system

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-03-01

In connection with the practicability of a solar thermal power generation system, examination was made on the technical economic problems and the operation method as well as on the problems of required performance of the constituent equipment, with the measuring method and performance evaluation method examined that are suitable for various devices. The items for the examination are as follows: (1) Silicon as the raw material for solar cells and its R and D, (2) Amorphous silicon solar cells, (3) R and D on low cost solar cells and array, (4) Basic design for photovoltaic generation system, and (5) Problems and technical subjects for solar cell standard measurement. The research themes and items for the above examination are listed as below: (1) Demand trend for raw material silicon, overseas trend, and development plan for polycrystalline silicon; (2) R and D plan for amorphous Si solar cell and its system, their optimum design, and their cost analysis and economic effect; (3) Technological investigation on cells and examination on array; (4) Basic design, peripheral equipment for system, and development schedule; (5) Report on the first actual state investigation concerning instrumentation of solar cells, i.e., on 'instrumentation and deviation in transformation efficiency', calibration system, problems of instrumentation of new device, problems of reliability test method, situation in various countries, and trend in atmospheric turbidimeter. (NEDO)

Research and development of system to utilize photovoltaic energy. Study on large-scale PV power supply system; Taiyoko hatsuden riyo system no kenkyu kaihatsu. Taiyo energy kyokyu system no chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on large-scale PV power supply systems in fiscal 1994. (1) On optimization of large-scale systems, the conceptual design of the model system was carried out which supposes a large-scale integrated PV power generation system in desert area. As a result, a pair of 250kW generation system was designed as minimum one consisting power unit. Its frame and construction method were designed considering weather conditions in the inland of China. (2) On optimization of large-scale transmission systems, as large-scale power transmission systems for PV power generation, the following were studied: AC aerial transmission, DC aerial transmission, superconducting transmission, hydrogen gas pipeline, and LH2 tanker transport. (3) On the influence of large-scale systems, it was estimated that emission control is expected by substituting PV power generation for coal fired power generation, the negative influence on natural environment cannot be supposed, and the favorable economic effect is expected as influence on social environment. 4 tabs.

FY 1999 survey report on the research survey on the formation of a social consensus on the introduction of the global warming mitigation technology; 1999 nendo ondanka taisaku gijutsu no donyu ni kakawaru shakaiteki goi keisei ni kansuru chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

As to the development and introduction of the global warming mitigation technology, the paper studied an approach to the formation of a social consensus and how to apply concrete methods and proposed a realistic approach in the light of the present situation of public enterprises in Japan. As tools and rules which are particularly important in activities of forming the consensus, the paper cited up what the PR control should be, responses to mass communications, HP making and regulation/preparation of the related laws, and made a concrete study. As examples in which there occurred friction with the society due to the insufficient formation of consensus, the following construction plans were taken up to consider problems, etc. in disclosure of the information in the plans: Underground Research Laboratory, movable weir in the Yoshino River, and waste disposal facilities at Fuimae tideland. Also in Japan, some methods for the consensus formation have been carried out, and in the survey, as concepts for classifying the methods, two different approaches, Public Outreach and Public Relations, were introduced. As to the former, a consensus formation method in the construction of power plants in Japan was introduced, and as to the latter, a method in consensus conferences in the U.K. (NEDO)

FY 1998 Report on field test project study for introduction of high-performance industrial furnaces. Detailed measurement study of FY 1998 joint research demonstration data; Koseino kogyoro donyu field test jigyo. 1998 nendo kyodo kenkyu jissho data no shosaina sokutei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Described herein are the FY 1998 results of measurement and study for introduction of the high-performance industrial furnaces. The NEDO's works for development of the high-performance industrial furnaces have been almost completed. The field tests are conducted to verify leveling and increasing temperature in the high-performance industrial furnaces. The data are collected in the existing and modified furnaces at the standard treating rate for each of the selected furnaces. The measured items are heat patterns of the works, temperature distributions within the furnace, heat balances in the combustion furnace, waste heat at the regenerative heat recovery unit, and exhaust gas components. The investigated items are names, materials, shapes, weights and quantities of the works; charging/discharging temperature; heating time; temperature in each furnace; consumption, types and heating values of the fuels used; air/fuel ratios; presence or absence of recuperator and its conditions when adopted; air temperature upstream and downstream of the heat accumulator, and exhaust gas temperature and components; temperature of the heat accumulator's external walls; cooling water rates, and inlet/outlet temperature, surface temperature of the furnaces' external walls; and furnace dimensions and structures. The measurements are done by thermocouples for various types of temperature, and O{sub 2}, CO2, CO, NOx meters and other analyzers for the components. The data are collected on a continuous basis. (NEDO)

Research report of FY 1997 on the environmentally acceptable coal utilization system introduction support project. Demonstration project on simplified desulfurizers; 1997 nendo seika hokokusho. Kankyo chowagata sekitan riyo system donyu shien jigyo (kan`i datsuryu setsubi ni kakawaru jissho jigyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

To reduce SOx with coal utilization, a desulfurizer is introduced in Thailand as diffusion activities in the demonstration program. The purpose is to reduce the environmental pollutants. For this desulfurizer, lime mud mainly composed of lime stone is used as an absorber. SO2 in the flue gas is absorbed by the slurry of lime mud, to form calcium sulfite. The calcium sulfite blown in the bottom of recycling tank is oxidized by oxygen in the air, to form gypsum. The gypsum is recovered as a by-product. In this fiscal year, a feeder of lime stone, spray nozzles, and various analysis apparatuses were supplied. Supervisors for electric instrumentation/control were also dispatched as well as for main body construction, to carry out the instrumentation setting works, check of sequences, and adjustment of apparatuses. After the test operation, supervisors for the demonstration operation were dispatched up to March 1998, to conduct the cooperation works between Japan and Thailand sides. Thus, successful and successive demonstration operation was confirmed. 21 figs., 6 tabs.

FY 2000 report on the survey of the project on field tests on the introduction of high performance industrial furnaces. Analysis/evaluation of the collected data; 2000 nendo koseino kogyoro donyu field test jigyo chosa hokokusho. Shushu data kaiseki hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of achieving the target of reduction in CO2 regarded as substance causing global warming which was agreed at COP3, the study has been made since FY 1993 on 'the development of high performance industrial furnaces (regenerative combustion furnace using heat storage type burner for realization of high temperature air combustion).' By applying the good results obtained, a field test project for introduction of high performance industrial furnace has been implemented for three years (FY 1998 - FY 2000) to confirm the actual performance, reliability, etc. Collection/arrangement were made mainly of the data obtained in this field test project for the introduction of high performance industrial furnaces in each fiscal year (1998, 1999 and 2000), and verification/evaluation and arrangement were made. In this R and D, energy conservation was achieved at a rate of more than 30% of the target. Also about NOx, the result was obtained that the NOx by energy saving can be reduced 50% in almost all kinds of furnace if adding the reduction amount in emission amount and the reduction amount by high temperature air combustion. About the quality, the good result was obtained. Downsizing was conducted in approximately 10 examples. (NEDO)

FY 1999 report on the survey of the reinforcement of the base for introduction/spread/improvement of clean energy vehicles in the Kinki region, Japan; 1999 nendo chosa hokokusho. Kinki chiiki clean energy jidosha donyu fukyu sokushin kiban kyoka chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Survey was made with the aim of studying measures to be taken for introduction/promotion of clean energy vehicles (CEV) in the Kinki region and of making a guidebook which included 8 CEV introduction menus based on the characteristics/needs in the Kinki region. In the survey of the state of CEV introduction in the Kinki region, a total number of the CEVs introduced in the region was estimated at approximately 5,300 (19.1% of the whole country), which indicated that the CEV introduction was increasing in comparison with the rate of the general vehicles registered (14.6% of the whole country). On the other hand, the fuel supply stations prepared such as eco-station are limited mostly to Osaka prefecture, which showed that the base is still unprepared. From the questionnaire survey made for 367 autonomous bodies and main 73 companies, problems and the needs for the wide area/large quantity spread were grasped, and various basic data were obtained. To solve problems, the setting-up of the Kinki CEV introduction/spread/promotion committee (CEV Kansai) was studied. (NEDO)

Study of reciprocating engine with Z mechanism. Part 1. Discussion of effect on the performances of new concept engine; Yodo shiten riron wo mochiita ofuku do engine ni kansuru kenkyu. 1. Shinkihon kozo no donyu ni yoru seino kojo no suisatsu

Energy Technology Data Exchange (ETDEWEB)

Yoshizawa, Y; Fukuzaki, S; Kanno, M [Yoshiki Industrial Co. Ltd., Yamagata (Japan)

1997-10-01

A new reciprocating engine was developed as an application of new mechanism named as `Z mechanism.` In this new engine, the piston motion is described by a simple sine function and gives lower velocity around top dead center than that in conventional piston engines. Thus, the mode of combustion in this engine is closer to constant-volume process and gives higher thermal efficiency than ordinary engines. Use of Z-mechanism also eliminated high-order components of vibration that ordinary engines suffer. Development high-performance engine was successfully conducted with this new mechanism. 4 refs., 11 figs., 1 tab.

FY 2000 report on the survey of the project on field tests on the introduction of high performance industrial furnaces. Analysis/evaluation of the collected data; 2000 nendo koseino kogyoro donyu field test jigyo chosa hokokusho. Shushu data kaiseki hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of achieving the target of reduction in CO2 regarded as substance causing global warming which was agreed at COP3, the study has been made since FY 1993 on 'the development of high performance industrial furnaces (regenerative combustion furnace using heat storage type burner for realization of high temperature air combustion).' By applying the good results obtained, a field test project for introduction of high performance industrial furnace has been implemented for three years (FY 1998 - FY 2000) to confirm the actual performance, reliability, etc. Collection/arrangement were made mainly of the data obtained in this field test project for the introduction of high performance industrial furnaces in each fiscal year (1998, 1999 and 2000), and verification/evaluation and arrangement were made. In this R and D, energy conservation was achieved at a rate of more than 30% of the target. Also about NOx, the result was obtained that the NOx by energy saving can be reduced 50% in almost all kinds of furnace if adding the reduction amount in emission amount and the reduction amount by high temperature air combustion. About the quality, the good result was obtained. Downsizing was conducted in approximately 10 examples. (NEDO)

Report on investigations in fiscal 2000 on the basic investigation on promotion of joint implementation. Introduction of central load dispatching center in Oman; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Oman koku ni okeru chuo kyuden shireijo no donyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In Oman, electric power supply is made by operating a large number of gas turbine generators. However, the operation is inefficient as a whole as a result of operating the generators provided with large reserves to minimize effects of unit failures in each power plant as one unit. Therefore, the present investigative study has begun from discussing the achievement of energy conservation and reduction of greenhouse gas emission by managing the demand and supply in an economical manner upon introducing a central load dispatching center (CLDC). Given the introduction of CLDC, the effects of introducing the equi-{lambda} method with still higher economy and of introducing the control system of reserve operation power may be summarized as follows: the energy saving effects (converted to crude oil quantity) are 22,400 toe/year for the former case and 35,800 toe/year for the latter case; and the greenhouse gas reduction effects are 52,000 t-CO2/year for the former case and 84,000 t-CO2/year for the latter case. This is an effective project with a considerable amount of effect as a result of introducing the equi-{lambda} and of introducing the control system of reserve operation power, while the investment amount is relatively small. The investment recovery period is 2.5 years and 2 years, respectively, making the project considerably promising as a CDM project. (NEDO)

Report on achievements in fiscal 1998. Development of technologies to put photovoltaic power generation systems into practical use - Research and development of solar beam power generation and utilization systems and ancillary technologies (Investigations and researches on meteorological data for optimal design); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (saiteki sekkei no tame no kisho data no chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Observations are being made in Takasaki City, Gunma Prefecture on insolation, putting emphasis on the north side, and insolation by wavelengths to put insolation estimation model on the north side slope into order. This is an attempt to put into order by using the model the data for insolation on slope in all azimuth, taking the meteorological offices all over the country as the object. With regard to monthly average insolation, it was verified that the existing estimation model can be applied to the north slope in the Takasaki area, whereas trial calculations were performed on the average daily cumulative insolation by azimuth and inclination angle in the Takasaki observation points. As a result, it was made clear that the insolation onto north side roofs in Japan is about 70% of that on the south side. With respect to the time cumulative slope insolation, it was made clear that the Perez's cumulative model can be applied to the Takasaki area. Spectral distribution of global and scattered solar radiation was put into order by insolation to have verified that the stronger the global solar radiation intensity, the greater the occupation ratio of shorter waves increases, or in other words, the spectral distribution of the global insolation can be formulated. Sky distribution of radiation is being measured by means of measuring the sky scanning type radiation and luminance distribution. (NEDO)

Fiscal 2000 project of inviting proposals for international joint research - invitation for international proposal (Power generation No.2). Achievement report on development of high-efficiency low-temperature power generation device using SOFC containing yttria-doped ceria layer; 2000 nendo kokusai kyodo kenkyu teian kobo jigyo - kokusai teian kobo (hatsuden No.2). Yttria gan'yu ceria so wo yusuru SOFC kokoritsu teion sadogata hatsuden sochi no kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts continue to develop a solid oxide fuel cell (SOFC) capable of consuming methane, propane, and the like, as fuel directly and of operation at 650 degrees C or lower. The efforts in concrete terms involve the development of an anode material, an electrolyte, and a cathode material not to suffer carbon precipitation and the evaluation of power generation performance of a hydrocarbon fueled single cell. Activities are conducted in the five domains of (1) the fabrication of an SOFC single cell and a preliminary study, (2) evaluation of solid electrolyte thermal stability using X-ray diffraction, (3) anodic carbon precipitation test and single cell performance test, (4) survey of technical trends overseas, and (5) the goal and self-management. In domain (1), technologies are developed to form thin film anodes of Ni-GDC (gadolinium-doped ceria), Cu-GDC, Ni-YSZ (yttria-stabilized zirconia), and the like, for which the ultrasonic spray method and slurry coat method are used. In the study of cell manufacturing, the anode support method and cathode support method are investigated. The anode support method is used to fabricate a thin film, a thin YSZ film is successfully fabricated for typical Ni-YSZ. (NEDO)

FY 1997 - FY 2000 reports on the results of the development of commercialization technology of the photovoltaic power system. Summary. R and D of the photovoltaic power generation utilization system/periphery technology (R and D of high reliability storage batteries); 1997-2000 nendo New sunshine keikaku seika hokokusho (Sokatsu ban). - Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu, Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (Koshinraisei chikuden sochi no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The R and D/evaluation were made from FY 1997 to FY 2000 of lead storage batteries that are applicable to the use for the absorption of abrupt power variations in photovoltaic power generation and peak shift/emergency use power source, and the results were summed up. In the study for prolonging the life, the following were carried out: development of the inexpensive corrosion-resistant lead alloy positive grid applicable to the photovoltaic power generation, development of the negative active material with a high sulfation control effect, selection of silica powder as electrolyte retainer, development of the charging control technology by the multi-stage constant current method, etc. As a result, energy density of the battery was more than 70W/L as a target, and the target life of 3,000 cycles was achieved in the life test. Further, cost reduction and deterioration judgment were studied. In the study of the group of batteries, a management system for group of batteries was developed. As a result of the 1-year field test, there were no problems on durability of the storage case, temperature difference among batteries, rise in temperature, etc. As to the developed seal type lead storage battery, the applicability to the photovoltaic power generation was acquired. (NEDO)

Fiscal 1995 report on the results of the subsidy operation under the Sunshine Project on the development of a geothermal water use power plant, etc. Development of the binary cycle power plant (development of the measurement while drilling system for geothermal wells); 1995 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu (binary cycle hatsuden plant no kaihatsu (chinetsusei kussakuji kotei joho kenchi system no kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The R and D were conducted of a detection system for measurement of data on the bottom hole of geothermal well, data transmission and signal processing, and an analysis system for well drilling trajectory control and well assessment while drilling of geothermal wells based on the data obtained by the detection system, and the results were reported of the technical development in fiscal 1995. In the development of the downhole detection unit, the following developments were conducted: mud pulse generator, bottomhole signal processor, mode switches, inclination information sensor, power source, measures against vibration/shock, sonde external equipment, tests to confirm heat resistance of electronic parts, and design/manufacture of testing devices. In the development of the surface detection unit, the development was made of experimental analysis program, interface program, and simulation. In the development of the analysis system, as a well trajectory control support system, made were a trajectory planning/display system and a trajectory prediction system. As a downhole assessment support system, made were a temperature analysis system and a pressure analysis system. 4 refs., 298 figs., 88 tabs.

Achievement report for fiscal 1999 on project for supporting the formation of energy/environmental technology verification project. International joint verification research project (Use of combined binary power generation systems at new geothermal fields on Mindoro Island, the Philippines, and comparison with conventional power generation systems); 1999 nendo Philippines koku Mindoro to no shinki chinetsutai ni okeru combined binary hatsuden hoshiki no tekiyo seika hokokusho. Conventional hatsuden hoshiki tono hikaku kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Concerning the Manito Lowlands geothermal field and the Montelago geothermal field where the systems are to be newly installed, the geothermal reservoir characteristics are assessed, and cost effectiveness is compared between different power generating systems. According to the investigations conducted into the two geothermal fields in the past, they are supposed to have geothermal potentials of the medium grade. Chemical analyses are conducted anew on this occasion into the hot spring water and fumarole gas, and the MT (magnetotelluric) method is implemented for the survey of reservoir distribution. It is now expected that approximately 20MWe will be exploited from each of the two geothermal fields. The power generation systems studied are the single flash type and double flash type for the conventional power generation system, and the cascade type, bottoming type, and two-phase binary type for the combined binary power generation system. As the result, it is concluded that the double flash type or two-phase binary type will be advantageous to the Manito Lowlands geothermal field, and the double flash type or bottoming type or two-phase binary type will be advantageous to the Montelago geothermal field. (NEDO)

Fiscal 1996 report on the results of the subsidy operation under the Sunshine Project on the development of a geothermal water use power plant, etc. Development of the binary cycle power plant (development of the measurement while drilling system for geothermal wells); 1996 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu (binary cycle hatsuden plant no kaihatsu (chinetsusei kussakuji kotei joho kenchi system no kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The R and D were carried out of a detecting system for measurement of data on the bottom of geothermal well, data transmission and signal processing, and an analysis system for well drilling trajectory control and well assessment while geothermal well drilling based on the data obtained by the detecting system. The paper reported the results of the technology development in fiscal 1996. In the development of the detecting system, improvement/design were conducted on a mud pulse generator constituting sonde, well bottom signal processing equipment, mode switch and inclined information sensor, and the system equivalent to the actual one was manufactured to conduct a running test at high temperature/pressure. Moreover, a test to confirm heat resistance of electronic parts was made for further improvement in heat resistance of the sonde, in order to obtain the data. In the development of an analysis system, conducted were enhancement of operability of the planning/indication portions of the well drilling trajectory supporting system, improvement of the data intake system, etc. In relation to the well assessment supporting system, carried out were heightening of operability of the temperature analysis portion and confirmation of accuracy increase. 5 refs., 253 figs., 72 tabs.

Report on achievements in fiscal 1998. Development of a waste disposal and recycle related technology. (Development of a technology to dispose of air bags adequately); 1998 nendo haikibutsu shori recycle kanren gijutsu kaihatsu air bag tekisei shori gijutsu no kaihatsu nado seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-12-01

This technological development is intended to develop a process technology to dispose adequately of air bags convergently when they are removed from waste cars, with consideration paid on environmental and safety aspects. This technology that can dispose of air bags remaining as air bag modules (ABM) in large quantity and adequately can solve the problems of maloperation in opening them in cars and noise in conventional disposal methods. The recovery and disposal system using an inflator can be expected of reducing work load on dismantling contractors and enhancing the work safety. Furthermore, the energy saving process utilizing combustion of plastics can save resources. However, this technology has not elucidated how dioxins, dust, smoke, sulfides, and nitrogen oxides are generated and how the generation can be prevented. Therefore, an exhaust gas dioxin testing facility and an exhaust gas treating facility were installed additionally to the existing heating treatment facility to develop a disposal technology to treat adequately the exhaust gases generated when ABMs are disposed conveergently in large quantity, and treat the waste water discharged from the facilities. Fiscal 1998 has performed preliminary tests to accumulate fundamental data, and design and installation of the above two facilities. (NEDO)

FY 2000 report on the basic survey to promote Joint Implementation, etc. Survey of the effective use of wastes at palm oil refineries; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Palm oil seisei kojo ni okeru haikibutsu yuko riyo chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

As to empty fruit bunches (EFB) which are wasted at the Lahad Datu plant of Felda Vegetable Oil Products Co. in Malaysia, a project was studied for energy substitution and greenhouse effect gas reduction by fluidized bed cogeneration facilities using this as fuel. In the project, studied was the introduction of on-site cogenerator of 7,800kW in generating-end output, and that of IPP cogenerator of 16,000kW as reference. As a result of the study, the energy substitution amount in toe in 20 years was approximately 376 k tons in case of on-site power generation/fluidized bed boiler and approximately 695 k tons in case of IPP and fluidized bed boiler. The amount of greenhouse effect gas emission in toe in 20 years was approximately 5,757 k tons and 11,654 k tons, respectively. Concerning the profitability, the internal earning rate was 3.32-8.47% in case of on-site power generation/fluidized bed boiler and 9.13-14.65% in case of IPP/fluidized bed boiler. It indicated the materialization of the project. (NEDO)

Research and development of photovoltaic power system. Study on structural defects in silicon-based amorphous materials; Taiyoko hatsuden system no kenkyu kaihatsu. Amorphous silicon kei zairyo no kozo kekkan ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Shimizu, T [Kanazawa University, Ishikawa (Japan). Faculty of Engineering

1994-12-01

Described herein are the results of the FY1994 research program for structural defects of silicon-based amorphous materials for solar cells. The study on light generation defects of the a-Si:H system and rejuvenation process by annealing establishes the effects of light irradiation time on changed neutral dangling bond density as a result of light irradiation at varying temperature of 77K, room temperature and 393K. The study on annealing to rejuvenate light generation defects of various types of a-Si-H systems establishes the activation energy distribution with respect to annealing to remove light-induced defects, showing that hydrogen affects the distribution of light-induced defects. The study on decaying process of light-induced ESR for undoped and N-doped a-Si:H systems observes the decaying process of light-induced ESR, after light is cut off, extending for a period of several seconds to several hours at 77K for the a-Si-H systems containing N in a range from 0 to 12at%. The other results presented are space distribution of neutral defects of light-irradiated a-Si-H systems, and rejuvenation process of light-induced spin for the a-Si(1-x)N(x):H composition. 6 figs.

Development of fundamental technigue of compressed air energy storage (CAES) gas turbine power generation and resistivity tomography. Asshuku kuki chozo (CAES) gas turbine hatsuden no kiban gijutsu no kaihatsu to hiteiko tomography

Energy Technology Data Exchange (ETDEWEB)

Hibino, S; Suzuki, K [Central Research Inst. of Electric Power Industry, Tokyo (Japan)

1991-12-01

Compressed air energy storage (CAES) has been studied as a promising storage system which has a good possibility of being put to practical use. Construction of the storage facility is required for CAES. For an economical construction of a storage facility, it is necessary to construct a storage facility by excavating, from the ground surface, a cavity in the ground. There is no case in Japan where rock storage is adopted with several tens of atmospheric pressure which is necessary for CAES. If highly pressurized air can be stored by the water sealing method, it is a very economical method in the case with hard rocks. As the first stem to verify the effectivity of the water sealing system, a water sealing experiment is performed in a boring hole. It is confirmed that water sealing can be possible up to about 40 atmospheres, and it is found that the resistivity, open joint distribution and coefficient of permeability of rocks have correlation as an investigating method for potential cracks in rocks and that resistivity tomography is effective for the investigation of cracks in rocks. 9 ref., 23 figs., 6 tabs.

Photovoltaic system at Nagaoka College of Technology. Fabrication of photovoltaic system and development of data logging system; Nagaoka kosen ni okeru taiyoko hatsuden. Setsubi no kochiku to data shuroku system no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Arimoto, M; Shirai, I; Togawa, K; Koshoji, H; Otaki, S [Nagaoka College of Technology, Niigata (Japan); Murata, M; Murata, K; Nomura, M [New Energy Corp., Tokyo (Japan)

1997-11-25

Reported in this paper is a photovoltaic power generation facility built in the yard of Nagaoka College of Technology. The purpose of this study is to find out if such a facility operates effectively in a heavy-snow region. A data logging system is also constructed. In a preliminary experiment, a 50W panel was installed, facing southwest at an inclination of 30degC, on the roof of the schoolhouse. A voltmeter, ammeter, and slide rheostat were used to perform necessary measurement. The panel temperature was approximately 50degC, and insolation was estimated at 70mW/cm{sup 2}. The data logging system is comprised of a personal computer, display, printer, etc. Using this system, voltage and current are measured with the load automatically adjusted, and the maximum power point is sought out and logged. In addition, insolation, ambient temperature, and panel temperature are logged. Data is logged every 10th minute and, when a day`s measurement is over, mean values are obtained for every hour and data is built for a power generation profile, all automatically. There is a plan for a wintertime power generation experiment. 3 refs., 5 figs.

Fiscal 1998 survey report. Assessment and analysis of collected data in wind power generation field test project; 1998 nendo furyoku hatsuden field test jigyo ni okeru shushu data hyoka kaiseki chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Examination was made on wind conditions, power generating characteristics, and the reliability of a system by analyzing the operation record of the wind power generation equipment which was installed at Hiraizumi-cho, Nishi-Iwai gun, Iwate prefecture and at Misaki-cho, Miura-shi, Kanagawa prefecture. The equipment at Hiraizumi had a rated output of 490 kW, and at Miura 400 kW. The period of the examination was from April, 1998 through February, 1999, the items for data collection being the generator output, generated energy, average wind velocity, record of abnormality occurrence, and maximum wind velocity. At Hiraizumi, annual average utilization rate was 12.9%; annual average operation rate, 49.9%; average wind velocity, 4.6 m/s; and maximum wind velocity of the period, 31 m/s. At Miura, annual average utilization rate was 16.5%; annual average operation rate, 77.0%; and average wind velocity, 5.0 m/s. The utilization rate is desirably 17%. The top three abnormalities were drop in AC control voltage, actuation of main shaft brake and eddy current/actuation of open phase relay, accounting for 83.3% of the total abnormalities at Hiraizumi, while they were unbalance in current, grid drop and automatic unwinding of cable, accounting for 74.5% at Miura. (NEDO)

Achievement report for fiscal 1981 on Sunshine Program. Practical application technologies for photovoltaic power systems (Development of peripheral technologies); 1981 nendo taiyoko hatsuden system jitsuyoka gijutsu seika hokokusho. Shuhen gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

As for their outputs, the 3kW separately-excited and self-excited photovoltaic power plants yield daily averages of 7.8kWh and 6.9kWh, respectively, and this means that the self-excited type is inferior to the separately-excited type in terms of conversion efficiency. Automatic measuring devices for photovoltaic characteristics are installed at Sapporo, Sendai, Nagoya, and Miyazaki, which will elucidate regional difference in photovoltaic characteristics. A simulation of photovoltaic characteristics is performed and the resultant value is compared with the yield of an experimental 3kW system, and the result of the comparison is found reasonable. Cell arrays are subjected to investigation for configurations lowest in output loss for the respective shadow patterns. Harmonic characteristics are analyzed under plural-interconnection circumstances. Studies are made to miniaturize and simplify system constituents, and it is found that a 3-hour storage is proper for a 3kW-class storage battery. It is also found that a self-excited type suffers less voltage fluctuation in interconnected operation on a small short-circuit capacity system. Possibilities are that independent operation is started when output is larger than load, which is to be detected by checking changes in phase, frequency, etc. Array configuration, arresters, and shielding wires are taken up for the study of measures to cope with direct thunder strokes. (NEDO)

FY 1998 annual summary report on photon measuring/processing techniques. Development of highly functional maintenance techniques for power generating facilities; 1998 nendo foton keisoku kako gijutsu. Hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The objectives are set to develop the techniques for non-destructive measurement of conditions of facility portions, especially those exposed to severe environments, e.g., elevated temperature and pressure, over a wide range; the techniques for measurement of leakage of, e.g., gases, at high sensitivity; the techniques of laser-aided welding and surface-modification treatment for the members exposed to severe conditions; and the techniques for generating photon beams of high quality and energy density as the tools therefor, in order to improve reliability and maintenance efficiency of power generating facilities. The R and D themes are microscopic processing technology: fabrication technology for functional micro-composite circuits; in-situ status measuring technology: gas concentration/component measurement technology, and photon wavefront compensation device technology; non-destructive composition measuring technology: high-sensitivity detection technology using short-wavelength photons; high-power all-solid-state laser technology: rod-type laser and slab-type laser; tightly-focusing all-solid-state laser technology: high-energy pulse, high-quality laser; and comprehensive investigation of photonics engineering: investigation for photon-applied measurement technologies. (NEDO)

FY 1974 Report on results of Sunshine Project. Research and development of binary cycle geothermal power generation plant (Part I); 1974 nendo binary cycle chinetsu hatsuden plant no kenkyu kaihatsu seika hokokusho. 1

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-05-30

The power generation system survey/research project surveys properties and the like of secondary fluids (e.g., n-butane and chlorofluorohydrocarbons); prepares the heat balances after taking into consideration the system concepts and thermodynamic characteristics of these fluids; and completes, based on the heat balances, basic designs of the major components (e.g., 10 MW plant turbine, evaporator and condenser), equipment layouts for the power plant, piping plans, and plant control system plans. For development of the turbine, the preliminary designs are drawn, based on the existing steam and gas turbine techniques, to complete the preparations for the detailed designs. For shaft sealing devices, the plan for the test apparatus is completed, the test procedures are drawn, and the preparations for the tests are partly completed. For the heat exchangers, the preliminary designs are completed for the optimum types. It is planned that the heating and cooling tubes for the heat exchangers are surface-treated to improve heat transfer coefficients. The surface treatment and surface patterns are studied, and the treated tubes are developed on a trial basis. The test unit for evaluating their performance is designed and constructed, thus completing the preparations for the tests. The corrosion test unit is installed, and the small-size corrosion simulation unit is completed. This report covers the results up to Chapter 2, Section 3, the remainder being described in JN0040364. (NEDO)

FY 1977 Annual report on Sunshine Project results. Survey and research on systems utilizing solar energy (Photovoltaic power generation systems); 1977 nendo taiyo energy riyo system chosa kenkyu seika hokokusho. Taiyoko hatsuden system

Energy Technology Data Exchange (ETDEWEB)

NONE

1978-03-31

This project is aimed at investigation on irradiation conditions of natural solar radiation to establish the performance evaluation methods; establishment of standard evaluation methods under natural solar radiation; and investigation on practical problems involved in the photovoltaic power generation systems. The research items are (1) photovoltaic power generation systems, and (2) standard evaluation methods for photovoltaic power generation systems installed on the ground. The item (1) includes the effect analysis in which existing Japanese residential buildings are selected to estimate possibility of installation of photovoltaic power generation systems and possible quantity of power generated; conceptual designs in which several systems conceivable at present are proposed and outlined, and a 30kW photovoltaic power generation system is taken up to investigate, e.g., solar cell arrays for the system, orthogonal conversion devices, associated facilities, conceptual designs of storage batteries, problems involved therein, and future research themes; and operation of the cell, which takes up operational examples of solar cell power sources, and operational problems viewed from the power transmission side. The item (2) proposes the standard evaluation methods (primary drafts) for the solar cell arrays and panels as those for photovoltaic power generation systems installed on the ground. (NEDO)

FY 1978 Annual report on Sunshine Project results. Survey and research on systems utilizing solar energy (Photovoltaic power generation systems); 1978 nendo taiyo energy riyo system chosa kenkyu seika hokokusho. Taiyoko hatsuden system

Energy Technology Data Exchange (ETDEWEB)

NONE

1979-03-01

This survey report provides the basic data for planning national projects to smoothly raise the large industry of solar cell industry in the future by studying how to promote the research and development projects for this area, continuously pursued from the establishment of the Sunshine Project. This report clarifies, first of all, the concept of long-term schedules for research and development of solar thermal power generation systems, based on which technical themes are concretely surveyed, and their economic viability and ripple effects on the other industries are analyzed. The industry of solar thermal power generation systems is a new industry, even based on the global horizons, backed up by the Japan's high-technological areas of electronics and semiconductor industries. It is one of important projects to be urgently developed, also viewed from the above standpoint. This report describes the long-term visions of solar thermal power generation systems, and the research and development projects therefor; stock materials for solar cells and problems involved therein; research and development projects for low-cost solar cells; photovoltaic power generation systems, and the research and development projects therefor; conceptual designs of photovoltaic power generation systems; and standard analytical procedures for solar cells, and technical problems involved therein. (NEDO)

Research and development of photovoltaic power system. Development of novel technologies for fabrication of high quality silicon thin films for solar cells; Taiyoko hatsuden system no kenkyu kaihatsu. Kohinshitsu silicon usumaku sakusei gijutsu

Energy Technology Data Exchange (ETDEWEB)

Shimizu, T [Kanazawa University, Ishikawa (Japan). Faculty of Engineering

1994-12-01

Described herein are the results of the FY1994 research program for development of novel technologies for fabrication of high quality thin films of silicon for solar cells. The study on the mechanisms and effects of chemical annealing reveals that the film structure greatly varies depending on substrate temperature during the hydrotreatment process, based on the tests with substrate temperature, deposition of superthin film (T1) and hydrotreatment (T2) as the variable parameters. Chemical annealing at low temperature produces a high-quality a-Si:H film of low defect content. The study on fabrication of thin polycrystalline silicon films at low temperature observes on real time the process of deposition of the thin films on polycrystalline silicon substrates, where a natural oxide film is removed beforehand from the substrate. The results indicate that a thin polycrystalline silicon film of 100% crystallinity can be formed even on a polycrystalline silicon substrate by controlling starting gas composition and substrate temperature. The layer-by-layer method is used as the means for forming the seed crystals on a glass substrate, where deposition and hydrotreatment are repeated alternately, to produce the thin crystalline silicon films of high crystallinity. 3 figs.

Achievement reports on joint research of solar energy power generation field test project in fiscal 1997. Part 1 of 3; 1997 nendo taiyoko hatsuden field test jigyo kyodo kenkyu seika hokokusho 1/3

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-08-01

This report is a collection of 101 achievement reports on joint research of solar energy power generation field test project. The contents of the achievement reports are the results and generalization of the joint research with respect to the solar energy power generation field test project. As regards the locations of executing the joint research, the locations by areas and applications are stated. By areas, the joint research was carried out on gymnasiums, parks, recreation centers in the standard areas, universities, sports facilities, public halls, agricultural associations, aged persons' homes, primary, middle and high schools, prefectural office buildings and industrial technology centers in cold districts; prefectural office buildings, agricultural associations, universities, museums, industrial technology centers in good insolation districts; museums, primary, middle and high schools, parks in strong wind and salt polluted districts; and universities and police stations in snowy districts. By applications, the joint research was performed on life cooperative halls, factories, nursery schools, hospitals, clinics, local newspaper companies, indoor warm-water swimming pools, and mushroom fields. (NEDO)

Achievement reports on joint research of solar energy power generation field test project in fiscal 1997. Part 2 of 3; 1997 nendo taiyoko hatsuden field test jigyo kyodo kenkyu seika hokokusho 2/3

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-08-01

This report is a collection of 26 achievement reports on joint research of a solar energy power generation field test project. The major contents of the achievement reports relate to the solar energy power generation field test project (summarized as manufacture and installation of solar energy power generation systems, summary of solar energy power generation facilities, peripheral devices, and daily schedule of the construction). The reports describe achievements of the joint research (names and achievements of the joint research, study presentation, lectures, literatures, status of patents, similar research in and cooperation with other research institutions), generalization of the research, and future problems. Locations of the joint research carried out are libraries, kindergartens, health and welfare centers, children's culture centers, general traffic centers, primary and middle schools, river water purifying facilities, credit banks, manufactories, retail shops at car parking areas, office buildings, hospitals, joint prefectural office buildings, municipal health centers, and prefectural general power generation control stations. (NEDO)

Reports on 1979 result of Sunshine Project. Investigation and research on solar energy utilization system (solar thermal power generation system); 1979 nendo taiyo energy riyo system chosa kenkyu seika hokokusho. Taiyonetsu hatsuden system

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-03-01

An investigation and research were conducted on the operation method of various solar thermal power generation systems and on the evaluation of the rating and cost performance; in the environmental test method for the equipment, the examination was continued for the test method and evaluation method concerning the absorbing surface and transmitting film; in the heat storing technology, an investigative research was done on the optimum heat storing method and energy conversion method suitable for the operation of the thermal power generation system, as well as performing, as an objective, a computer simulation on the total system with the purpose of clarifying the heat storing capacity. The results in the year were as follows. The operation method for solar thermal power generation was examined, as were the energy analysis, evaluation method of 1 MW pilot plant, the optimum utilization system of solar energy in the long run including its application, and technological economical problems to be solved for the next large solar thermal power generating plant. A discussion was carried out on the endurance test of the selective absorbing surface and transmitting film and on the durability of the reflection mirror. Evaluation and examination were made on the various materials of the 1 MW pilot plant. A review was done on various heat accumulating devices for solar thermal generation, mathematical thermal characteristics of heat accumulating devices, and future energy storing methods and problems. (NEDO)

FY 1978 Annual report on Sunshine Project results. Survey and research on systems utilizing solar energy (Photovoltaic power generation systems); 1978 nendo taiyo energy riyo system chosa kenkyu seika hokokusho. Taiyoko hatsuden system

Energy Technology Data Exchange (ETDEWEB)

NONE

1979-03-01

This survey report provides the basic data for planning national projects to smoothly raise the large industry of solar cell industry in the future by studying how to promote the research and development projects for this area, continuously pursued from the establishment of the Sunshine Project. This report clarifies, first of all, the concept of long-term schedules for research and development of solar thermal power generation systems, based on which technical themes are concretely surveyed, and their economic viability and ripple effects on the other industries are analyzed. The industry of solar thermal power generation systems is a new industry, even based on the global horizons, backed up by the Japan's high-technological areas of electronics and semiconductor industries. It is one of important projects to be urgently developed, also viewed from the above standpoint. This report describes the long-term visions of solar thermal power generation systems, and the research and development projects therefor; stock materials for solar cells and problems involved therein; research and development projects for low-cost solar cells; photovoltaic power generation systems, and the research and development projects therefor; conceptual designs of photovoltaic power generation systems; and standard analytical procedures for solar cells, and technical problems involved therein. (NEDO)

FY 1974 Report on results of Sunshine Project. Research and development of binary cycle geothermal power generation plant (Part II); 1974 nendo binary cycle chinetsu hatsuden plant no kenkyu kaihatsu seika hokokusho. 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-05-30

The power generation system survey/research project surveys properties and the like of secondary fluids (e.g., n-butane and chlorofluorohydrocarbons); prepares the heat balances after taking into consideration the system concepts and thermodynamic characteristics of these fluids; and completes, based on the heat balances, basic designs of the major components (e.g., 10 MW plant turbine, evaporator and condenser), equipment layouts for the power plant, piping plans, and plant control system plans. For development of the turbine, the preliminary designs are drawn, based on the existing steam and gas turbine techniques, to complete the preparations for the detailed designs. For shaft sealing devices, the plan for the test apparatus is completed, the test procedures are drawn, and the preparations for the tests are partly completed. For the heat exchangers, the preliminary designs are completed for the optimum types. It is planned that the heating and cooling tubes for the heat exchangers are surface-treated to improve heat transfer coefficients. The surface treatment and surface patterns are studied, and the treated tubes are developed on a trial basis. The test unit for evaluating their performance is designed and constructed, thus completing the preparations for the tests. The corrosion test unit is installed, and the small-size corrosion simulation unit is completed. This report covers the results in and after Chapter 2, Section 4, those before being described in JN0040363. (NEDO)

Evaluation and analysis of long-term operation data for a grid connected PV generation system; Nippon de hajimete no gyakuchoryu ari kojin jutaku taiyoko hatsuden system no choki unten jisseki no hyoka kaiseki

Energy Technology Data Exchange (ETDEWEB)

Ishida, T.; Kozuma, S.; Hagihara, R.; Kishi, H.; Uchihashi, K.; Tsuda, S.; Nakano, S. [Sanyo Denki Co. Ltd., Tokyo (Japan)

1997-11-25

Long-term operation of a photovoltaic power generation system installed in a private residence in Osaka in 1992 is evaluated. Since the sale of power by back flow was approved five years ago, it has been working continuously without troubles. The evaluation covers the array output coefficient, inverter performance, system output coefficient, and power generation and sale track records. The findings obtained are mentioned below. Regular seasonal changes are observed in the array output coefficient, high in winter and low in summer, but the variation is smaller in amorphous arrays than in polycrystalline arrays. The monthly level of inverter performance is almost in all months higher than 0.90 specified for standard operation. The overall system output coefficient is 0.749, which is higher than the average value in NEDO`s field test business report. A total of 7852kWh has been generated since the system started operation five years ago, of which 3787kWh or 48% has been sold. 3 refs., 9 figs., 5 tabs.

New Sunshine Program for Fiscal 2000. International cooperative project for developing photovoltaic power system practicalization technology (General edition); 2000 nendo New sunshine keikaku. Taiyoko hatsuden system jitsuyoka gijustu kaihatsu kokusai kyoryoku jigyo (Sogoban)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Fiscal 2000 international cooperation for the research, development, and popularization of photovoltaic power systems is compiled. In carrying out international cooperation relating to the photovoltaic power generation program of IEA (International Energy Agency), etc., officers were sent to the 15th and 16th executive committee meetings, where they deliberated on plan formulation and budget making. They also participated in the activities of Task 1: Exchange and dissemination of information on photovoltaic power systems, Task 2: Operational performance and design of photovoltaic power systems and subsystems, Task 3: Use of photovoltaic power systems in stand-alone and island applications, Task 5: Design and grid interconnection of building integrated and other dispersed photovoltaic systems, Task 7: Photovoltaic power systems in the built environment, Task 8: Study on very large scale photovoltaic power generation systems in deserts and other unexploited regions, and Task 9: Technical co-operation for photovoltaic market deployment. A discussion was made on the holding of a 4th IEA photovoltaic power system executive conference. In addition, Japan-Australia and Japan-Oman bilateral cooperative projects were implemented. (NEDO)

FY 1999 report on the basic survey of the promotion of Joint Implementation, etc. Beijing Yanshan Petrochemical Co./cogeneration; 1999 nendo Beijing Yanshan sekiyu kako yugen koji netsu heikyu fukugo hatsuden chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For a combination with COP3 Clean Development Mechanism (CDM), the paper reported the FY 1999 survey of the cogeneration project of Beijing Yanshan Petrochemical Co. The existing two heavy oil fueled boilers (steam output: 240t/h) are dismantled, and two gas turbines and two waste heat boilers (steam output: 241t/h, electricity output: 136.9MW) are installed. The energy conservation effect is approximately 0.91 million tons/year of crude oil. The effect of reduction in greenhouse gas emissions is CO2 2.83 million tons/year. A plan on system interconnection, distribution, electricity, instrumentation control was drawn up. The construction term is planned to be about two and a half years. The initial investment amount is 700 million yuan {+-} 100 million yuan. The expense vs. energy conservation effect was calculated as 98t (crude oil conversion)/year/million yen, and the expense vs. greenhouse gas emission reduction effect 302t-CO2/year/million yen. Concerning the profitability, the generating cost was 0.4 yuan/kWh which dropped from the selling power cost of the Yanshan area, 0.45 yuan/kWh. As candidates of the natural gas fueled cogeneration, there are possibilities of 10 sites and 550MW scale only in the Beijing area. (NEDO)

Achievement reports on joint research of solar energy power generation field test project in fiscal 1997. Part 1 of 3; 1997 nendo taiyoko hatsuden field test jigyo kyodo kenkyu seika hokokusho 1/3

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-08-01

This report is a collection of 101 achievement reports on joint research of solar energy power generation field test project. The contents of the achievement reports are the results and generalization of the joint research with respect to the solar energy power generation field test project. As regards the locations of executing the joint research, the locations by areas and applications are stated. By areas, the joint research was carried out on gymnasiums, parks, recreation centers in the standard areas, universities, sports facilities, public halls, agricultural associations, aged persons' homes, primary, middle and high schools, prefectural office buildings and industrial technology centers in cold districts; prefectural office buildings, agricultural associations, universities, museums, industrial technology centers in good insolation districts; museums, primary, middle and high schools, parks in strong wind and salt polluted districts; and universities and police stations in snowy districts. By applications, the joint research was performed on life cooperative halls, factories, nursery schools, hospitals, clinics, local newspaper companies, indoor warm-water swimming pools, and mushroom fields. (NEDO)

Research and development of system to utilize photovoltaic energy. Survey on system and peripheral technologies for utilization of photovoltaic power; Taiyoko hatsuden riyo system no kenkyu kaihatsu. Riyo system ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the survey results on systems and peripheral technologies for use of PV power in fiscal 1994. On the case study of PV communities, as housing zone PV community, Seibu Kitanodai housing estate mainly composed of detached houses, and the Suwa area of Tama New Town of apartment houses were selected to study PV power generation on a roof, wall and window. The result clarified that generated energy of a detached house reaches 3-4 times as much as consumed one, that of an apartment house is nearly equal to consumed one, and power generation of nearly 380MW is possible based on expected housing supply until 2000. As urban core zone PV community, the survey result on Ebisu Garden Place clarified that the expected PV power supply rate is 10% or more, 20% and 30% or more for hotel and office buildings, high-rise apartment building more than 30 stories, and medium-rise one of 10 and several stories, respectively. In Sakura industrial estate, the maximum generated power was nearly equal to consumed power in a weekday, and as inverse power flow in a holiday was considered, the annual PV power supply rate was extremely high.

Research and development of peripheral technology for photovoltaic power systems. Study of nickel-hydride storage battery for photovoltaic generation systems; Shuhen gijutsu no kenkyu kaihatsu. Taiyoko hatsuden`yo suiso denchi no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on R and D of nickel-hydride storage battery for photovoltaic generation systems in fiscal 1994. (1) On the study on low-cost electrode materials, the physical properties and electrode characteristics were studied of the prototype hydrogen absorbing alloys prepared by substituting Cu or Ni for Co in Mm(Ni-Co-Mn-Al)5 (Mm: mixture of rare earth elements). The result clarified that it is difficult to reduce Co content in the alloy to 0.4 atom or less. Simple heat treatment and milling processes in production of hydrogen absorbing alloy electrodes were achieved by adopting an improved metal mold and gas atomization method. Characteristics and cycle life of the Ni positive electrode prepared by applying active paste material of Ni(OH)2 were studied, however, the result showed only lives of nearly 300 cycles. (2) On the study on electrode structure for high-performance (long-life) battery, the 3-D porous metal electrode support was evaluated, and various battery configurations were studied. 11 figs., 1 tab.

FY 1998 annual report on the compilation of the data related to new energy technology development. Photovoltaic power generation; 1998 nendo shin energy gijutsu kaihatsu kankei data shu sakusei chosa hokokusho. Taiyoko hatsuden

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The data, centered by those related to generation of photovoltaic (PV) power as one branch of new energy, are collected and systematically compiled under the following fields. (Significance of adopting PV power systems) describes, e.g., CO2 reduction effect and energy pay-back time for different customers, i.e., nation, local governments, industries and individual households. (Present status of solar cell markets) describes solar cell production by region, cell technology and industry; shipments by application; production values; and prices. (PV system policies overseas) compares the policies of the industrialized countries for PV power systems with those of Japan. (Introduction of PV power systems overseas) compares situations of various countries in PV power system introduction with those of Japan with respect to estimated quantities of PV systems installed and target quantities. (Financial supports for PV power system installation) describes subsidies, tax benefits and loans adopted in Japan. Other items covered herein include transition of PV-related budgets, flow of PV system introduction, measures taken by central and local governments, and contacts for PV-related enterprises. (NEDO)

33rd Solar Energy Promotion Committee Meeting - 8th Photovoltaic Power Liaison Meeting. Report for fiscal 1995; Dai 33 kai taiyo energy suishin iinkai dai 8 kai taiyoko hatsuden renrakukai (1995 nendo hokoku)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-04-22

The above-named events were convened in the period of April 22-24, 1996, when a total of 46 presentations were given on research achievements. In the session on crystalline Si systems, 9 essays were presented, and a discussion was held about 'Technological tasks for realizing 20% efficient module.' In the session on ultrahigh III-V group systems, 4 essays were presented, and a discussion was held on 'Tasks about technology development for ultrahigh efficiency III-V compound solar cell.' In the session on thin film (a-Si) systems, 14 essays were presented, including one about an approach toward the elucidation of photodegradation. In the symposium, a subject 'System-to-cell transverse task' was discussed. In the session on system related matters, 10 essays were presented, and a discussion was held about 'Architecture and photovoltaic system.' In the session on thin film (thin film polycrystalline Si, chalcopyrite) systems, 8 essays were presented, and a subject was discussed titled 'Toward the establishment of a system of widespread diffusion and massive introduction.' (NEDO)

33rd Solar Energy Promotion Committee Meeting - 8th Photovoltaic Power Liaison Meeting. Report for fiscal 1995; Dai 33 kai taiyo energy suishin iinkai dai 8 kai taiyoko hatsuden renrakukai (1995 nendo hokoku)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-04-22

The above-named events were convened in the period of April 22-24, 1996, when a total of 46 presentations were given on research achievements. In the session on crystalline Si systems, 9 essays were presented, and a discussion was held about 'Technological tasks for realizing 20% efficient module.' In the session on ultrahigh III-V group systems, 4 essays were presented, and a discussion was held on 'Tasks about technology development for ultrahigh efficiency III-V compound solar cell.' In the session on thin film (a-Si) systems, 14 essays were presented, including one about an approach toward the elucidation of photodegradation. In the symposium, a subject 'System-to-cell transverse task' was discussed. In the session on system related matters, 10 essays were presented, and a discussion was held about 'Architecture and photovoltaic system.' In the session on thin film (thin film polycrystalline Si, chalcopyrite) systems, 8 essays were presented, and a subject was discussed titled 'Toward the establishment of a system of widespread diffusion and massive introduction.' (NEDO)

Achievement reports on joint research of solar energy power generation field test project in fiscal 1997. Part 3 of 3; 1997 nendo taiyoko hatsuden field test jigyo kyodo kenkyu seika hokokusho 3/3

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-08-01

This report is a collection of 40 achievement reports on joint research of a solar energy power generation field test project. The major contents of the achievement reports relate to the solar energy power generation field test project (summarized as manufacture and installation of solar energy power generation systems, summary of solar energy power generation facilities, status of installation of solar cells, peripheral devices, and daily schedule of the construction). The reports describe achievements of the joint research (names and achievements of the joint research, study presentation, lectures, literatures, status of patents, similar research in and cooperation with other research institutions), generalization of the research, and future problems. Locations of the joint research carried out are hospitals, township hospitals, a science hall for youths, study and educational cities, primary schools, middle schools, high schools, universities, senior health centers, a life cooperative association, retails shops, factories, office buildings, joint governmental office buildings, Shinkansen stations, prefectural industrial testing centers, health and welfare centers, FM broadcasting studios, a town operated hall of technologies, prefectural office buildings and training centers. (NEDO)

'Development and introduction of ice water conveyance system and verification of low temperature blast system' for leveling off electric power load; Denryoku fuka heijunka wo misueta 'hyosui hanso hoshiki no kaihatsu donyu to teion sofu hoshiki no kensho'

Energy Technology Data Exchange (ETDEWEB)

Kuriyama, T. [Nikken Sekkei Ltd., Osaka (Japan)

1999-11-05

From the view point of the earth environment protection, energy-saving in the field of building air-conditioning has become increasingly important. On the other hand, the utilization of nighttime electric power is needed to ease the electric power supply and demand problem, and in this connection, a wider introduction of the ice heat storage system is recommended as one of the means to cope with such a problem. However, the ice heat storage system also has problems to be solved such as energy savability, and economy. Under such circumstances, various technical research and development efforts as well as evaluation thereof have been made centering around the 'technical development of the ice water conveyance system' and the 'evaluation of the low temperature blast system' for energy-saving, facility cost reduction and electric power load leveling off, and as a matter of fact these systems have been installed in actual buildings with useful results. (author)

Fiscal 1999 report on basic research for promotion of joint implementation programs. Research on introduction of dual mode bus system for greenhouse gas reduction; 1999 nendo onshitsu koka gas sakugen no tame no dual mode bus system donyu ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

A feasibility study is conducted of the above-named system in Malaysia, to be linked to COP3 (Third Session of the Conference of the Parties to the United Nations Framework Convention on Climate Change) clean development mechanism (CDM). The dual mode bus system (DMBS) is a combination of advantages of the rail running stock such as monorails and the road running stock in that the buses when running on dedicated roads are automatedly formed into a linear formation and travel at a specified economical speed. When running on ordinary roads, the formation is broken into individual buses, and they spread in the town where they travel in a planar pattern. The economical speed and reduction in air drag thanks to the linear formation saves fuel and reduces CO2 emissions. The complementary relationship to be formed with the existing public transportation systems will also function positively. Studies are conducted on condition that two routes be laid in the Kuala Lumpur urban area and one in the new city Putra Jaya. All the three routes exhibit a high economic internal rate of return, but their financial internal rate of return indicates that probabilities are low that they will pay as private businesses. They will need financial supports such as subsidies. Contribution to CO2 reduction may be slight when attention is paid only to the partial changeover from the existing bus system to DMBS but larger contribution will be found in crossover from private cars to DMBS which is higher in quality of service. (NEDO)

Fiscal 2000 regional consortium research and development project - regional new technology creation research and development. Development of bio-recycling technology for bio-wastes; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki shingijutsu soshutsu kenkyu kaihatsu seika hokokusho. Seibutsukei haikibutsu no bio recycle gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts are exerted to develop a closed brewing system for 'shochu (a Japanese distilled liquor)' and vinegar and a non-combustion type thermal recycling system based on the methane fermentation of farm animal's excretion and sludge. Activities are conducted in the three fields of (1) the development of a zero emission shochu and vinegar brewing process, (2) development of a non-combustion type thermal recycling method, and (3) a commercialization plan. Studied in field (1) are the brewing of 'shochu' by a new process (kaeshi-shikomi), preparation of vinegar out of the lees of 'shochu' brewing, evaluation of the physiological activity of vinegar and 'shochu' lees, cost efficiency evaluation of zero emission 'shochu' and vinegar brewing processes, and the like. In field (2), the methane fermentation conditions for garbage, sludge, and farm animals' excretion are studied, and a non-combustion type thermal recycling process and the like are evaluated for cost efficiency. In field (3), marketability is studied for vinegar made by fermentation, actualities of the recycling of bio-wastes and energy recovery therefrom are examined, and marketability is studied for regional distributed power generation. (NEDO)

Fiscal 2000 regional consortium research and development project - regional new technology creation research and development. Development of bio-recycling technology for bio-wastes; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki shingijutsu soshutsu kenkyu kaihatsu seika hokokusho. Seibutsukei haikibutsu no bio recycle gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts are exerted to develop a closed brewing system for 'shochu (a Japanese distilled liquor)' and vinegar and a non-combustion type thermal recycling system based on the methane fermentation of farm animal's excretion and sludge. Activities are conducted in the three fields of (1) the development of a zero emission shochu and vinegar brewing process, (2) development of a non-combustion type thermal recycling method, and (3) a commercialization plan. Studied in field (1) are the brewing of 'shochu' by a new process (kaeshi-shikomi), preparation of vinegar out of the lees of 'shochu' brewing, evaluation of the physiological activity of vinegar and 'shochu' lees, cost efficiency evaluation of zero emission 'shochu' and vinegar brewing processes, and the like. In field (2), the methane fermentation conditions for garbage, sludge, and farm animals' excretion are studied, and a non-combustion type thermal recycling process and the like are evaluated for cost efficiency. In field (3), marketability is studied for vinegar made by fermentation, actualities of the recycling of bio-wastes and energy recovery therefrom are examined, and marketability is studied for regional distributed power generation. (NEDO)

FY 1999 cooperation program - Comprehensive research cooperation in environmental technology. Research cooperation in toxic/hazardous waste management in the Laguna de Bay region; 1999 nendo kenkyu kyoryoku jigyo. Kankyo gijutsu sogo kenkyu kyoryoku - Raguna ko chiiki ni okeru yudoku yugai haikibutsu ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of establishing preventive measures for water contamination in the Laguna de Bay region, the Philippines, where the water contamination is in progress and the eutrophication is feared, a research cooperation project was carried out on the water quality contamination monitoring technology (measuring method/analysis method/prediction method). In the survey of the state of generation of toxic/hazardous waste, the following were grasped based on the existing data: amount of use of toxic/hazardous substances in factories, state of generation of waste, situation of the processing/disposal, etc. In the detailed survey of the situation of pollution in the Laguna de Bay region, specimens of water quality and bottom material were collected from the lake and rivers thereinto, and qualitative/quantitative analysis of contaminants was made using atomic absorption spectrophotometer and gaschromatograph mass spectrometer. As to the evaluation of pollutant sources and control method, the paper conducted the introduction of measures generally taken against pollutant sources, study of a method to grasp the behavior of contaminants by the environmental assessment method for the closed water area, etc. The training was also conducted for researchers/engineers widely in charge of management of toxic/hazardous waste in the Philippines. (NEDO)

Project subsidized by the Sunshine Project in fiscal 1982. Report on achievements in the project commissioned from NEDO - development of a hot water utilizing power generation plant and development of a binary cycle power generation plant (Researches on corrosion preventive measures and the cycle optimum for the plant); 1982 nendo nessui riyo hatsuden plant no kaihatsu seika hokokusho. Binary cycle hatsuden plant no kaihatsu (fushoku taisaku no kenkyu oyobi plant saiteki cycle no kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-03-01

As the element research on a 10-MW class geothermal binary cycle power plant to be built in the coming term, researches were made on corrosion preventive measures and the cycle optimum for the plant. This paper reports the achievements in fiscal 1982. In the research on corrosion preventive measures, different kinds of materials were buried in three locations having different soil natures to study corrosion due to soil. The corrosion rate of heat conducting pipes using the heat media R114 was estimated as very small as 1/40 of the corrosion rate in geothermal waters. In the research on the cycle optimum for the plant, experimental research was performed on thermo-dynamic properties and thermal stability of the mixed media using R114 as the main component. As a result, the R114/R112 system was found to have higher pressure than R114, but the media circulation amount is less, and the output at the power transmission terminal increased by 5 to 10%. The system showed the most excellent heat cycle characteristics. In the research of building a power plant installed with two different power generation systems, a computer program was prepared that calculates heat balances all at once for the case of installing a geothermal binary cycle power plant in a geothermal steam power plant. (NEDO)

Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Research and development of photovoltaic power utilizing system and peripheral technologies (Research and development of novel type solar cell module integratable with building materials - Highly durable roof module); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (shinkenzai ittaigata taiyo denchi module no kenkyu kaihatsu - kotaikyusei yane module)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

A thin-film solar array, a large roof panel, and an interconnecting power conditioner are integrated into one and single structural member for the development of a residential photovoltaic power system in which a unit AC (alternating current) output is collected from each panel. In fiscal 1999, in the study of highly durable materials for solar cell modules and of their structure, a thin film compound solar cell module was enlarged to 82cm times 71cm, evaluated for performance, and installed on the third test house. In the study of collecting AC power from the solar cell module, a compact power conditioner for a roof panel which had been in test operation on the roof of the laboratory since 1998 was checked for practical performance, improved, and evaluated for system generation efficiency. In the study of a highly durable roof module structure, problems pertaining to heat radiation from the rear side steel sheet, the burning of the junction box, etc., were solved, and the module passed a verification test under the Building Standard Law. In the validation of the roof module for which power generation performance and meteorological conditions had already been continuously measured for 19 months, it was found that the roof module suffered no troubles such as water leak or deformation. (NEDO)

Report on achievements in fiscal 1998. Development of technologies to put photovoltaic power generation systems into practical use - Development of solar beam power generation and utilization systems and ancillary technologies (Research and development of building material integrated solar cell modules - high-durability roof modules); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (shinkenzai ittaigata taiyo denchi module no kenkyu kaihatsu (kotaikyusei yane module))

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

With the target set on a system with a roof array efficiency of 8.5%, and a system cost of 170 yen/W, development is being made on a large roof panel and its construction technology, which is capable of AC output by integrating into a large roof panel the compound thin film solar cells having glass/CdS/CdTe/rear air chamber/rear metal, and the inverter. In the cell constituting materials and the structure design, sealants were evaluated, the painting process was developed, and two kinds of structures were prepared. The frameless type has a lamination structure, and a prototype module of 886 times 664 mm was fabricated, and the frame type has a double sealing structure, and a prototype module 600 times 900 mm was fabricated. Prototype modules that can be fixed on a rail type fixing stand were fabricated and constructed, having demonstrated sufficient workability. In addition, a prototype small inverter with system coordination protection was operated actually, and the initial stage malfunctions were corrected. Two demonstration buildings were built, and the whole process was performed from assembly and transportation of the modules and to the installation thereof at the construction site. (NEDO)

Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Research and development of photovoltaic power utilizing system and peripheral technologies (Research and development of novel type solar cell module integratable with building materials - Novel multilayer structure module); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (shinkenzai ittaigata taiyo denchi module no kenkyu kaihatsu - shinfukuso kozo module)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The project aims to develop solar cell modules of a novel multilayer structure, based on the resin filling structure, hollow structure, and the laminate structure, and integratable with building materials. In fiscal 1999, for the development of cells and submodule structures, cells and submodules were fabricated which were usable with various specimens. In the case of design oriented cells, electrode structures and linkage methods were improved for the enhancement of power generation performance, and a hollow structure and a laminate structure were fabricated. As for the 4m{sup 2}-large module (laminate structure), a specimen with dummy cells arranged along its periphery was fabricated. For cost reduction, a study was made about a module (laminate structure) integrated with an ALC (autoclaved lightweight concrete) board, and the kind of surface glass, cell arrangement, and back sheet types and their respective designs were evaluated. It was then concluded that the module was fit for practical application. The module was then checked for wind endurance in a wind endurance test, for electric characteristics, and for flame inhibition capability in a fire prevention/resistance test. (NEDO)

Fiscal 1995 achievement report. Development of entrained bed coal gasification power plant (Part 4 - Pilot plant operation); 1995 nendo seika hokokusho. Funryusho sekitan gaska hatsuden plant kaihatsu - Sono 4. Pilot plant unten sosa hen

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The 200 tons/day entrained bed coal gasification pilot plant constructed for establishing the technology of integrated coal gasification combined cycle was subjected to operational tests, and the fiscal 1995 results are compiled. In fiscal 1995, 1328 hours and 3 minutes (8 gasification operations) was recorded with gasification furnace facility, 899 hours and 53 minutes with the gas clean-up facility, 831 hours and 27 minutes with the gas turbine facility (11 startups for the generation of 6657 MWh), and 1958 hours and 2 minutes with the treatment furnace and 1331 hours and 10 minutes with the denitration unit of the safety/environment-related facility. The details of starts and stops were described in graphs which covered Runs D13, D14-1, D14-2, E1, D15, and A14. Operating procedures were studied and compiled for the plant start/stop schedule, general guidelines, gasification furnace facility, gas clean-up facility (dry type desulfurization facility), gas clean-up facility (dry type dedusting facility), gas turbine facility, real-pressure natural-size combustor test facility, and the safety/environment-related facility. (NEDO)

FY 1999 report on the results of the joint study - project on the public facility use photovoltaic power generation field test; 1999 nendo kokyo shisetsunadoyo taiyoko hatsuden field test jigyo kyodo kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-07-01

In the field test, solar cell panels were installed on rooftop, and inverters were installed indoors. The electric power generated was connected at high pressure with electric installation of facilities and was also supplied to power equipment, lighting, air conditioning, etc. in facilities. The FY 1999 results were summarized. The installation of photovoltaic power generation facilities at 137 places and the results of the study were summarized in this report including a new university co-op building, Tokyo Metropolitan Advanced Technology Education Center, Suwano Center House of Fukushima prefecture, Environment Center of Saga prefecture, Educational Foundation Utsukushino Kindergarten, Hikarigaoka Park of Yamagata prefecture, Koiwai factory of Koiwai Dairy Products Co., Social Welfare Corporation Kameyama Ayumi Nursery School, etc. (NEDO)

Fiscal 1994 achievement report. Development of entrained bed coal gasification power plant (Part 4 - Pilot plant operation); 1994 nendo seika hokokusho. Funryusho sekitan gaska hatsuden plant kaihatsu - Sono 4. Pilot plant unten sosa hen

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-07-01

The 200 tons/day entrained bed coal gasification pilot plant constructed for the establishment of the technology of integrated coal gasification combined cycle power generation was operated for testing, and the results are put together. Operating hours recorded were 1347 hours and 7 minutes for the gasification furnace facility (7 gasification operations), 752 hours and 22 minutes for the gas clean-up facilities, 425 hours and 20 minutes for the gas turbine facility (6 startups for generating 2616.1 MWh), and 1852 hours for the treatment furnace and 1304 hours and 32 minutes for the denitration system in the safety/environment-related facility. Detailed graphs were drawn for the description of starts and stops in Run D8, Run D9 (1-3), Run D10, Run D11, and in Run D12. Operating procedures were studied and then compiled for the plant start-stop schedule, general guidelines, gasification furnace facility, gas clean-up facility (dry type desulfurization facility), gas clean-up facility (dry type dedusting facility), gas turbine facility, real-pressure natural-size combustor test facility, and for the safety/environment related facility. (NEDO)

Fiscal 1999 research report. Research on photonic measurement and processing technology (Development of advanced maintenance technology for power plant facilities); 1999 nendo foton keisoku kako gijutsu seika hokokusho. Hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This report summarizes the fiscal 1999 research result on R and D of measurement technology, laser welding and surface treatment technology, and generation technology of photon beam, for improvement of the quality and maintenance efficiency for power plant facilities. In the study on fabrication of functional micro-composite circuits, the equipment for forming circuits on substrates by carrying particles with gas was developed whose geometric standard deviation is 1.17 for 26nm particles. In the study on gas concentration measurement technology, development of the variable-wavelength laser beam source for measurement, fabrication of thin films by epitaxial growth equipment, and computer simulation of sensitivities for quantum IR photo- detectors were promoted. In the study on photon wavefront compensation device technology, the technology for fabricating such device with (411)A surface orientations and asymmetric quantum well structures was developed. In the study on high-sensitivity detection technology using short- wavelength photon, to develop a high-energy resolution fluorescent X-ray detector, favorable electric properties of superconducting X-ray detecting devices were confirmed at nearly 0.1K. (NEDO)

Research and development of peripheral technology for photovoltaic power systems. Research and development of redox flow battery for photovoltaic power generation; Shuhen gijutsu no kenkyu kaihatsu. Taiyoko hatsuden`yo redox denchi no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on R and D of redox flow battery for photovoltaic power generation in fiscal 1994. (1) On the production method of electrolyte, silica reduction treatment was attempted to use ammonium metavanadate recovered from boiler as electrolyte of redox flow battery. Silica removal rates more than 90% were achieved by crystallizing V as polyvanadate while keeping molten silica. It was ascertained in minicell experiment that trivalent and quadrivalent V electrolytes produced from recovered V are applicable to continuous charge/discharge operation for one week. (2) On development of battery systems, the relation between battery characteristics and physicochemical properties of carbon fiber electrodes was studied to improve carbon fiber electrodes. The efficiency of 80% was achieved at current density of 160mA/cm{sup 2} by use of layered electrodes, resulting in considerable cost reduction. Performance evaluation operation of the 2kW battery prepared in the last fiscal year was also carried out. 4 figs.

Feasibility study for international collaboration on photovoltaic power generation and long-distance energy transmission technologies utilizing desert areas environment; Sabaku chiiki wo riyoshita taiyoko hatsuden chokyori yuso gijutsu ni kakawaru kokusai kyoryoku kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

A workshop was held at Tokyo in March, 1997 on the research and development and feasibility study for international collaboration on photovoltaic (PV) power generation and long-distance energy transmission technologies utilizing desert areas environment. Two speakers from the USA, one from Italy, and two from China were invited, and four speakers in Japan presented papers. A total of 48 persons participated. In the technical sessions, `World energy demand and PV system potential` by Prof. Kurokawa, `Long distance transmission of PV power` by Mr. A. Invenizzi, `Case studies of large scale PV systems distributed throughout desert areas of the world` by Mr. Hirasawa, `Linking renewable energy resources around the world` by Mr. P. Meisen, `Properties of large scale PV plant in the USA` by Mr. J. Benner, `Future prospect of PV electrification in China` by Mr. Kong Li, `Application of large-scale PV systems in deserts in China` by Mr. Isomura, and `Effects of large-scale PV power plant in a climatic desert areas` by Prof. Ihara were presented. 38 refs., 62 figs., 29 tabs.

FY 1999 report on the verification test on the system interconnection of the photovoltaic power system in Malaysia; 1999 nendo Malaysia ni okeru taiyo denchi hatsuden system no keito renkei jissho shiken seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

JET and SIRIM Behad, which is the standards and industrial research institute in Malaysia, worked this project together, and installed the Photo Voltaic Generation System (hereinafter refferred to as 'PV system') on the roof of the research building for researching basic conditions in the practical use of the PV system by gathering basic data. The power quality of a supply system necessary for a grid connection of the PV system was researched in the evidential experiment. Moreover, the invasion level and the invasion frequency to the PV system of the thunder surge by the peculiar weather condition in this region were researched. In addition, the requisite for the islanding function for the alternative emergency power supply was investigated. The contents of this project were composed of the three items. (1) research of the power quality in low voltage distribution system. Before and after the PV system is connected with the supply system, basic data concerning the power quality of the voltage, the current, and the frequency fluctuation, etc. in the system was collected. (1)measurement and investigation of the power quality under the current low voltage distribution system. By connecting ad monitoring recorder with a lower voltage distribution system, the current power quality i.e. voltage, current, frequency the fluctuation of voltage and frequency at the regular time were measured and investigated. (2) The power quality in the supply system grid connection of the PV system was measured and investigated. The voltage and the frequency in the case of supply system grid connection of the PV system were compared with the current state of preceding clause 1 and the stability of the power quality was evaluated. Moreover the output power of the solar battery was connected with the measurement device and then the surface temperature of the solar battery module, DC voltage, current and quality of solar radiation were measured. The subject in the practical use of the PV system in Malaysia was extracted through these experiments. (2) Research of level and frequency of the thunder surge. 1. Measurement of level and frequency of the thunder surge by the thunder surge counter. The thunder surge counter was set up respectively on the positive line and the negative line of the solar battery. These signals are taken into the memory of the thunder surge counter, and the level and the frequency data of the thunder surge which invade the PV system were accumulated. 2. Evaluation by simulation. The PV system was evaluated to the thunder surge obtained in preceding clause 1 by the simulation. In addition the simulation analysis was conducted by the system equivalent circuit on the assumption of the thunder surge current at the location of the system. (3) Research of the islanding function of the PV system as the backup power supply was evaluated when blacking out. (NEDO)

Report on survey for high-performance industrial furnace introduction field test project in fiscal 1999. Activities to promote proliferation of the introduction to subject project related business entities; 1999 nendo koseino kogyoro donyu field test jigyo chosa hokokusho. Taisho jigyosha eno fukyu sokushin katsudo

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This paper reports the survey on high-performance industrial furnace introduction field test project in fiscal 1999. The development of a high-performance industrial furnace having been performed by NEDO since fiscal 1993 has completed the fundamental development research in fiscal 1998, and the planned achievements were verified (large energy saving, reduction of NOx emission, and down-sizing). Upon the result, the introduction field test project has started in fiscal 1998 for three years until fiscal 2000. The number of research items adopted in fiscal 1998 was 58, and those in fiscal 1999 was 51, which are progressing smoothly at the present. Reduction in CO2 emission of 50,000 tons was demonstrated as the achievement in fiscal 1998, and NOx emission realized the regulation value or lower in cities wherein each operator is executing the project. Several cases of down-sizing were also reported. In the proliferation promoting project in fiscal 1998, activities were made mainly to the subject project related business entities in relation with the development achievements and general technologies for the high-performance furnace. In fiscal 1999, communication transmission was continued by using information tools on introduction of the achievements and technologies. Attempts will be made on promoting the proliferation of the field test project in the future through a number of technology lecture meetings performed by specialists. (NEDO)

Survey report for fiscal 1998. Surveys on possibility of introducing element technologies and future technological trends in the ECO and ENERGY city projects; 1998 nendo chosa hokokusho. Ekoene toshi project ni okeru yoso gijutsu donyu kanosei to kongo no gijutsu doko ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Covering ECO and ENERGY projects currently on the way under the New Sunshine Project, discussions were given on the possibility of utilizing the technological achievements, and the technological problems therein, from the energy supply and utilization aspects. Taken up as the basic concept of the ECO and ENERGY projects is 'optimization and implementation of a cascade-type energy system in cities under environmental restrictions'. Targets were placed on optimization of a total system including the demand side (a topping system), optimization of a total system including secondary energy other than heat (electric power and gas for example), optimization of energy efficiency for the system as a whole, and minimization of environmental load. The ECO and ENERGY technologies that are assumed for the future application were classified into the following six fields: the optimal energy supply system development field, heat storing technology field, thermoelectric power generation field, environment friendly heat pump system technology field, waste heat utilizing heat cycle technology field, and LNG cold heat utilizing technology field. (NEDO)

FY 1996 report on the results of the development of superconductor power application technology. Study of a total system, etc. (Investigational study of the introductory effect); 1996 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. Total system nado no kenkyu (donyu koka no chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Under the secondary interim assessment made in FY 1995 between the assessment committee of the energy/environment technology development sectional meeting of the Industrial Technology Deliberation Council and NEDO, in this project, the following were conducted in FY 1996: study of trial manufacture of superconductor motor model machine and R and D of element technology (conductor technology/refrigerator technology). The study was proceeded mainly with Super-GM, and as to the motor, the preparation for test on a part of the model machines was finished. Considering FY 1998 which is the final year of this project, the investigational study in FY 1996 aims at accumulating/arranging/analyzing the data which help judge how to proceed with the future R and D of superconductor power application technology continuously based on the secondary interim assessment. For superconductor motor and various superconductor power appliance, economical/technical feasibilities and methods of R and D and surveys of trends in Japan and abroad for the R and D were made important items. Further, 'R and D of the basement of superconductor power application' proposed in the secondary interim assessment (R and D of the combination of elements which become the basement of equipment technology over a stage of parallel R and D of element technology of conductor, etc.) targeted the presentation of concrete details. (NEDO)

Report on feasibility study for introduction of biomass energy in Town of Kuzumaki. Town of milk, wine and clean energy, located at N.L. 40 degrees; Kuzumakicho biomass energy donyu kanosei chosa hokokusho. Hokui 40 do, milk to wine to clean energy no machi

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-02-01

The feasibility study is conducted specifically for construction of a biomass plant in drawing the new energy visions for Town of Kuzumaki, Iwate Pref. The town is raising domestic animals, approximately 10,700 dairy cattle, 900 beef cattle, 2,800 hogs, and 18,000 chickens, actively producing the products, including approximately 40,000 tons/y of milk. On the other hand, these animals are discharging the excreta totaling around 500 tons/d, and adequate disposal and most effective utilization of the excreta as the resources provide the challenges to overcome. The project for constructing a demonstration model investigates treatment of the excreta discharged from 200 dairy cattle by an anaerobic fermentation plant, which uses the excreta and other organic wastes as the stock materials, and utilization of the biogas energy produced by the plant. The project is also considering to demonstrate the cycles of utilization of the digested sludge discharged from the fermentation process as the organic liquid compost. The economic evaluation results indicate that the plant gains a total income of 8.715 million/yen at a total expense of 8.575 million yen/y. (NEDO)

Survey report for fiscal 1998. Surveys on possibility of introducing element technologies and future technological trends in the ECO and ENERGY city projects; 1998 nendo chosa hokokusho. Ekoene toshi project ni okeru yoso gijutsu donyu kanosei to kongo no gijutsu doko ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Covering ECO and ENERGY projects currently on the way under the New Sunshine Project, discussions were given on the possibility of utilizing the technological achievements, and the technological problems therein, from the energy supply and utilization aspects. Taken up as the basic concept of the ECO and ENERGY projects is 'optimization and implementation of a cascade-type energy system in cities under environmental restrictions'. Targets were placed on optimization of a total system including the demand side (a topping system), optimization of a total system including secondary energy other than heat (electric power and gas for example), optimization of energy efficiency for the system as a whole, and minimization of environmental load. The ECO and ENERGY technologies that are assumed for the future application were classified into the following six fields: the optimal energy supply system development field, heat storing technology field, thermoelectric power generation field, environment friendly heat pump system technology field, waste heat utilizing heat cycle technology field, and LNG cold heat utilizing technology field. (NEDO)

Fiscal 2000 project on measures for assisting and diffusing environmentally-friendly coal utilization system introduction. CMG recovery/utilization system joint demonstration project; 2000 nendo kankyo chowagata sekitan riyo system donyu shien nado fukyu taisaku jigyo chosa hokoku. CMG kaishu riyo system kyodo jissho jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

A CMG (coal mine gas) recovery/utilization system was designed, constructed, and then demonstrated at a model coal mining district in Liaoning Province for the purpose of contributing to the solution of energy and environment related problems in China. The recovery system demonstration test, aiming to improve on safety and productivity of coal mining and to supply recovered gas with stability, involved gas drainage test boring, mine sealing, sealed gas induction control, centralized gas monitoring, etc., which were carried out at the coal mine working face. A utilization system demonstration test was conducted, and CMG would continue to be supplied to the current users and CMG utilization would be started at the other 6 coal mines. For the supply of CMG to large-scale gas consuming areas, steel materials were manufactured and processed for spherical gas holders and denitrification facilities, gas holders were constructed, pipe lines were installed, and a provisional gas supply was carried out. For the transfer and diffusion of the technology, Chinese engineers were trained in Japan and Japanese engineers were dispatched to China. (NEDO)

FY 1996 report on the results of the development of superconductor power application technology. Study of a total system, etc. (Investigational study of the introductory effect); 1996 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. Total system nado no kenkyu (donyu koka no chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Under the secondary interim assessment made in FY 1995 between the assessment committee of the energy/environment technology development sectional meeting of the Industrial Technology Deliberation Council and NEDO, in this project, the following were conducted in FY 1996: study of trial manufacture of superconductor motor model machine and R and D of element technology (conductor technology/refrigerator technology). The study was proceeded mainly with Super-GM, and as to the motor, the preparation for test on a part of the model machines was finished. Considering FY 1998 which is the final year of this project, the investigational study in FY 1996 aims at accumulating/arranging/analyzing the data which help judge how to proceed with the future R and D of superconductor power application technology continuously based on the secondary interim assessment. For superconductor motor and various superconductor power appliance, economical/technical feasibilities and methods of R and D and surveys of trends in Japan and abroad for the R and D were made important items. Further, 'R and D of the basement of superconductor power application' proposed in the secondary interim assessment (R and D of the combination of elements which become the basement of equipment technology over a stage of parallel R and D of element technology of conductor, etc.) targeted the presentation of concrete details. (NEDO)

Effect of operating methods of wind turbine-generator system on net power extraction under wind speed fluctuations in fields; Hendo fukyoka deno doryoku chushutsu kara mita furyoku hatsuden system no unten seigyoho ni kansuru kosatsu

Energy Technology Data Exchange (ETDEWEB)

Wakui, T. [Japan Society for the Promotion of Science, Tokyo (Japan); Hashizume, T.; Ota, E. [Waseda University, Tokyo (Japan). School of Science and Engineering

2000-01-25

The effect of operating methods of wind turbine-generator system on net power extraction under wind speed fluctuations is discussed in relation to the dynamic behavior of the system. The system is composed of a Darrieus-Savonius hybrid wind turbine and a load generator. In this paper, two types of operating method are examined; constant tip speed ratio operation for stand-alone power systems (Scheme 1) and synchronous operation for utility power systems (Scheme 2). The computed results of the net extracting power using our dynamic simulation model show that the dominant factor of power extraction in Scheme 1 is the dynamic characteristics of rotational components and that it is important to select the appropriate rated wind speed in Scheme 2. Thus, it is concluded that a conformable operating method and rated power output of the system exist for each wind condition. In particular, small-scale systems, which are smaller than approximately 10 kW-system range, are desirable to be operated under a constant tip speed ratio as stand-alone power systems. (author)

Achievement report for fiscal 1998 on joint research business (2/2). Photovoltaic power generation field test for public facilities; 1998 nendo kokyo shisetsu nadoyo taiyoko hatsuden field test jigyo (2/2). Kyodo kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-07-01

Photovoltaic power generation systems are experimentally installed at public facilities at various locations, and subjected to field tests in which they experience long-term operation under real loads. Mie Prefectural Iidaka Senior/Junior High School has a 10kW solar cell system installed on the south-side roof of the school house. The system is linked to an in-house transformation station and the power generated by the system is supplied to the lighting and air-conditioning facilities in the building, and surplus if any is transmitted to the Chubu Electric Power Co., Inc., system. A field test is being conducted to determine if there are usability and safety in the 10kW system. A number of like systems are undergoing field tests, installed at a comprehensive technological training center of Kyushu Electric Power Safety Association, Kongo Gakuen Senior High School, Sakata Nursery School, Taiyo Daiichi Nursery School, Minami Kindergarten, Neyagawa Ishizu Old People's Home, Co-Op Living Konan, Factory Hishimeki, Tochigi Fuji Industries, Gamo-cho Hirabayashi Public Hall, Fukuoka Prefectural Culture Complex, Yatsusugi Forest Schooling Center, Osaka Prefectural Murano Water Purification Plant, Yamanashi Institute of Environmental Sciences, Utatsu-cho Town Office, Ginga Gakuen Junior High School, etc. (NEDO)

FY 1977 Annual report on Sunshine Project results. Survey and research on systems utilizing solar energy (Solar thermal power generation systems); 1977 nendo taiyo energy riyo system chosa kenkyu seika hokokusho. Taiyo netsu hatsuden system

Energy Technology Data Exchange (ETDEWEB)

NONE

1978-03-31

This project is aimed at surveys and researches on operation, economic efficiency and performance evaluation of solar thermal power generation systems, and test methods, e.g., for aging the materials for their devices, in order to establish the methods for evaluating their performance. For operation of solar thermal power generation systems, a feasible system is a hybrid with another system, e.g., thermal power or nuclear system. For economic efficiency, heat-storage capacity will be based on power generation for around 4 hours a day for a solar system to be installed in Japan. The construction and light/heat-collecting costs should be reduced to around 300,000 yen/kW and 13,000 to 21,000 yen/m{sup 2}, respectively, in order to keep the power generation cost at around 23 yen/kWH. The energy analysis of solar thermal power generation, based on the data given by the industrial correlation tables, indicates that the total energy required for construction of the system can be recovered in 2 to 3 years. Also outlined are construction of a 1MW pilot plant and its facilities, and designs of the pilot plants with a curved surface or tower type light collector. A total of 12 types of reflection mirrors are screened for establishing the air-exposure testing methods. Methods for treating back surface edges of the reflection mirrors are also investigated. (NEDO)

Subsidized project for development of technology in putting photovoltaic power generation system into practice. Report of international joint demonstrative R and D on photovoltaic power generation system; Taiyoko hatsuden system kokusai kyodo jissho kaihatsu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The following joint researches are in progress utilizing natural conditions and social systems in Nepal, Mongolia, Thailand, Malaysia and Vietnam for the purpose of enhancing environmental adaptability, reliability, etc., of technologies. (1) Nepal; accelerated demonstrative research utilizing highland conditions, (2) Mongolia; demonstrative research of movable type photovoltaic power generation system, (3) Thailand; demonstrative research of photovoltaic generation system for battery-charging stations, (4) Malaysia; accelerated demonstrative research utilizing tropical conditions, and (5) Vietnam; demonstrative research of hybrid system on photovoltaic power generation and micro hydro power generation. The research assets of (1) and (3) whose researches have been finished were provided gratis for the co-researcher countries. In (5), on the basis of the geographical conditions such as annual average quantity of solar radiation, conduit for water-turbine, energy complementing relation, load demand, and degree of installation difficulty, Trang Village in Vietnam was selected, with a system decided on PV:100 kW/MH:25 kW/control system. The MH is an induction generator. The primary pieces of equipment are a generator, a storage battery, an inverter and a system control panel. (NEDO)

Achievement report for fiscal 1998 on joint research business (2/2). Photovoltaic power generation field test for industrial purposes; 1998 nendo sangyo nadoyo taiyoko hatsuden field test jigyo (2/2). Kyodo kenkyu gyomu seika hokokushyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-07-01

Solar cell systems are installed on the roofs of facilities at various locations, and verification tests are conducted for usability and safety they will exhibit after prolonged operation under real loads, and this project aims at the popularization of photovoltaic systems. At Children's Ferrite and Science Museum of Nikaho Town, Akita Prefecture, a 20kW solar cell system is installed on the rooftop, and a 20kW inverter in the machine house. The power obtained is connected in a high-voltage interconnection to electric facilities in the museum, and supplied to in-house power facilities, illuminating systems, and air-conditioning equipment. Operation-related data are recorded in a data recording unit. Similar facilities are installed at corporations and institutions such as WAIDA Works, Kuriyama Shop, Nikko Building, Kiya Works, Aichi Prefectural Tobishima Junior High School, Gunma Prefectural Niisato Hall of Commerce and Industry, Ube Techno-Enji Corporation, Tezukayama Gakuin University, Kinki Kensetsu K.K., Takaoka Electric Manufacturing Company, Aichi Prefectural Incorporated Educational Institution Miura Gakuen, Asaguchi Taxi Company, Family Mart, etc., and field tests are under way for them. (NEDO)

Achievement report for fiscal 1998 on joint research business (1/2). Photovoltaic power generation field test for public facilities; 1998 nendo kokyo shisetsu nadoyo taiyoko hatsuden field test jigyo (1/2). Kyodo kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-07-01

Photovoltaic power generation systems are experimentally installed at public facilities at various locations, and subjected to field tests in which they experience long-term operation under real loads. At Livelihood Cooperative Association Co-Op Kanagawa, a photovoltaic cell system is installed on the roof, facing true south, of its Yokohama eastern district joint purchase center, and the power generated by the system is utilized as interconnected with the commercial distribution line connecting to its power facilities. It is called a '10kW Photovoltaic Power Generation Model System,' and is subjected to a verification test, carried over from the previous fiscal year, centering about its usability and safety. Similar systems are also installed at many locations, such as the Kadosawa Bridge district of Ebina City, Kanagawa Prefectural Industrial Technology Research Center, Shiga Prefectural University, Suntory Museum, Fukui Institute of Technology, Saigo Police Station, Higashi-Murayama Water Purification Plant, Kanagawa Prefectural Disaster Prevention Center, Toyosato-cho Health Center, Kyodo Gakusha School, Sakuragi Nursery School, Yagi Junior High School, Shizuoka Prefectural Environmental Radiation Monitoring Center, Tanabe City Health Center. (NEDO)

Researches regarding a constructing problem of a PV system. Part 1. Conscious investigation by means of a questionnaire survey; Taiyoko hatsuden system ni okeru kenchikuteki shomondai no kenkyu. 1. Anketo chosa ni yoru ishiki chosa

Energy Technology Data Exchange (ETDEWEB)

Nakajima, Y; Yamazaki, R; Kuroki, T [Kogakuin University, Tokyo (Japan)

1996-10-27

The installation and introduction of photovoltaic power generation systems (PVS) in buildings are growingly expected in the construction field from now, coupled with the marketing of a solar cell module as a product for a construction material in the form of an external wall or a roof material for example. For this purpose, it is necessary at first to summarize problems that may arise at the time of or after the installation of PVS as a product. This paper examines an opinion poll, degree of recognition, current problems, etc., of PVS as a result of a questionnaire survey given to engineers and architects engaged in the actual construction business. The degree of recognition and interest was very high. Consultation or request for PVS installation was much more than predicted in numbers. Roughly 50% of the respondents reacted positively for the future installation request of PVS and, combined with the respondents who answered to look into the installation tentatively, not less than 90% were of a forward-looking opinion. The 85% of the respondents was not aware of the monitor business system for residential PVS. Further, the survey clearly brought out the importance of cost problems. 1 ref., 11 figs., 3 tabs.

Achievement report for fiscal 1998 on joint research business (2/2). Photovoltaic power generation field test for public facilities; 1998 nendo kokyo shisetsu nadoyo taiyoko hatsuden field test jigyo (2/2). Kyodo kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-07-01

Photovoltaic power generation systems are experimentally installed at public facilities at various locations, and subjected to field tests in which they experience long-term operation under real loads. Mie Prefectural Iidaka Senior/Junior High School has a 10kW solar cell system installed on the south-side roof of the school house. The system is linked to an in-house transformation station and the power generated by the system is supplied to the lighting and air-conditioning facilities in the building, and surplus if any is transmitted to the Chubu Electric Power Co., Inc., system. A field test is being conducted to determine if there are usability and safety in the 10kW system. A number of like systems are undergoing field tests, installed at a comprehensive technological training center of Kyushu Electric Power Safety Association, Kongo Gakuen Senior High School, Sakata Nursery School, Taiyo Daiichi Nursery School, Minami Kindergarten, Neyagawa Ishizu Old People's Home, Co-Op Living Konan, Factory Hishimeki, Tochigi Fuji Industries, Gamo-cho Hirabayashi Public Hall, Fukuoka Prefectural Culture Complex, Yatsusugi Forest Schooling Center, Osaka Prefectural Murano Water Purification Plant, Yamanashi Institute of Environmental Sciences, Utatsu-cho Town Office, Ginga Gakuen Junior High School, etc. (NEDO)

Achievement report in fiscal 1999 on commissioned research project. 'Model project for facilities to effectively utilize wastes from industrial complexes in Thailand' Project for 1999 Volume 1; 1999 nendo seika hokokusho. Tai ni okeru kogyo danchi sangyo haikibutsu yuko riyo setsubi moderu jigyo - 1

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With an objective to reuse industrial wastes and effectively utilize them as a petroleum replacing energy resource, and attempt to reduce consumption of fossil fuel in Thailand where increase in discharge of industrial wastes is estimated, a model project for facilities to effectively utilize wastes from industrial complexes has been carried out. This paper reports the achievements in fiscal 1999. Specifically, the project calls for incineration in fluidized bed incinerators of industrial wastes discharged from factories in industrial complexes possessed by the Industrial Estate Authority of Thailand (IEAT), recovery of waste heat from waste heat recovering boilers to generate process steam, which is supplied to the factories in the complexes. The current fiscal year, which is the first current year of the project, has put into order the operations shared by Japan and Thailand, compiled the various procedures and schedules into the form of appendices to the agreement, and executed signing of the agreement. Thereafter, the Japanese side has carried out decision on the specifications of the facilities, the basic designs, the detailed designs of facilities to be arranged by Japan, and the fabrication of some of the devices according to the descriptions of the agreement appendices. The volume 1 summarizes the agreement appendices, and the specifications of the main devices. (NEDO)

Achievement report in fiscal 1999 on commissioned research project. 'Model project for facilities to effectively utilize wastes from industrial complexes in Thailand' Project for 1999 Volume 3; 1999 nendo seika hokokusho. Tai ni okeru kogyo danchi sangyo haikibutsu yuko riyo setsubi moderu jigyo - 3

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With an objective to reuse industrial wastes and effectively utilize them as a petroleum replacing energy resource, and attempt to reduce consumption of fossil fuel in Thailand where increase in discharge of industrial wastes is estimated, a model project for facilities to effectively utilize wastes from industrial complexes has been carried out. This paper reports the achievements in fiscal 1999. Specifically, the project calls for incineration in fluidized bed incinerators of industrial wastes discharged from factories in industrial complexes possessed by the Industrial Estate Authority of Thailand (IEAT), recovery of waste heat from waste heat recovering boilers to generate process steam, which is supplied to the factories in the complexes. The current fiscal year, which is the first current year of the project, has put into order the operations shared by Japan and Thailand, compiled the various procedures and schedules into the form of appendices to the agreement, and executed signing of the agreement. Thereafter, the Japanese side has carried out decision on the specifications of the facilities, the basic designs, the detailed designs of facilities to be arranged by Japan, and the fabrication of some of the devices according to the descriptions of the agreement appendices. The volume 3 summarizes the inspection reports other than those included in the Volume 2. (NEDO)

Achievement report in fiscal 1999 on commissioned research project. 'Model project for facilities to effectively utilize wastes from industrial complexes in Thailand' Project for 1999 Volume 2; 1999 nendo seika hokokusho. Tai ni okeru kogyo danchi sangyo haikibutsu yuko riyo setsubi moderu jigyo - 2

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With an objective to reuse industrial wastes and effectively utilize them as a petroleum replacing energy resource, and attempt to reduce consumption of fossil fuel in Thailand where increase in discharge of industrial wastes is estimated, a model project for facilities to effectively utilize wastes from industrial complexes has been carried out. This paper reports the achievements in fiscal 1999. Specifically, the project calls for incineration in fluidized bed incinerators of industrial wastes discharged from factories in industrial complexes possessed by the Industrial Estate Authority of Thailand (IEAT), recovery of waste heat from waste heat recovering boilers to generate process steam, which is supplied to the factories in the complexes. The current fiscal year, which is the first current year of the project, has put into order the operations shared by Japan and Thailand, compiled the various procedures and schedules into the form of appendices to the agreement, and executed signing of the agreement. Thereafter, the Japanese side has carried out decision on the specifications of the facilities, the basic designs, the detailed designs of facilities to be arranged by Japan, and the fabrication of some of the devices according to the descriptions of the agreement appendices. The volume 2 summarizes the inspection reports in the referential materials. (NEDO)

Report on achievements in fiscal 1998. Development of technologies to put photovoltaic power generation systems into practical use - Development of solar beam power generation and utilization systems and ancillary technologies (Research and development of building material integrated solar cell modules - modules with new multi-layer structure); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (shinkenzai ittaigata taiyo denchi module no kenkyu kaihatsu (shinfukuso kozo module))

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Development is being made on a panel type module that can be used together with an air bubble concrete board (ALC board), and is provided with design characteristics. The development work includes trial fabrication and evaluation of a module with new multi-layer structure, and development of a technology to unitize cells and submodules, and a systematizing method. In the trial fabrication and evaluation, flame retardant and uninflammable modules using fluororesin, and modules with as large area as 4 m{sup 2} were fabricated on a trial basis, in addition to the modules with the basic structure. These modules were given evaluations on such wall material properties as wind pressure resistance, heat and cracking resistance, and fire resistance. In a deformation resistance test considering the integrated use with the ALC board, the developed modules showed a good result. In developing the cells with design characteristics, discussions were given on the inter-cell wiring methods. Development was made on a method to establish a unit structure based on the design and size of a building. In developing the systematization method, the trial fabrication method was applied to a module with lamination structure, a module integrated with the ALC board, and a large-area hollow module to have fabricated the top-light spandrels. (NEDO)

FY 1989 report on the results of the development of the entrained bed coal gasification power plant. Part 1. Element study; 1989 nendo seika hokokusho. Funryusho sekitan gaska hatsuden plant kaihatsu - Sono 1. Yoso kenkyu hen

Energy Technology Data Exchange (ETDEWEB)

NONE

1990-03-01

For the purpose of establishing the technology of integrated coal gasification combined cycle power generation, element study was conducted of a 200t/d entrained bed coal gasification pilot plant, and the FY 1989 results were summarized. In the gasification test using 2t/d gasifier equipment, the following were carried out: test on gasification of the coal proposed for pilot plant, test on changes in coal feed ratio, analysis of trace gas elements in coal, study of the fixed bed gas refining system, etc. In the study of large gas turbine combustor for demonstration machine, development of combustor which makes stable combustion in the low load region possible, development of low NOx combustor which controls the conversion of nitrogen compounds such as ammonia in coal gasification gas to NOx, development of combustor which makes the optimum and effective cooling possible by combining film cooling, impingement cooling, etc. In the study of simulation of the combined power generation total system, verification tests on the control mode switching function of the general load pressure control system, movement to meet anomaly of the control system, integrated cooperation control system, etc. (NEDO)

Research and development of photovoltaic power system. Study on growth mechanism of a-Si:H and preparation of the stable, high quality films; Taiyoko hatsuden system no kenkyu kaihatsu. Amorphous silicon no seimaku kiko to kohinshitsuka

Energy Technology Data Exchange (ETDEWEB)

Hirose, M [Hiroshima University, Hiroshima (Japan). Faculty of Engineering

1994-12-01

This paper reports the result obtained during fiscal 1994 on research on a film forming mechanism for amorphous silicon for solar cells and its quality improvement. In in-situ observation on plasma CVD surface reaction by using the total reflection infrared absorbing spectroscopy, an observation on a real time basis was performed on the reaction process of an a-Si:H surface in contact with gas mixture plasma composed of SiH4 + CH4. In microscopic observation on initial processes of amorphous silicon growth, surface morphological change before and after a-Si:H deposition at 200{degree}C was observed by using an inter-atomic force microscope. The observation verified that a-Si:H has grown to an atomic layer. In research on defect density in a-Si:H fabricated under high-speed film forming conditions, analysis was made on correlation between the film forming speed at 250{degree}C and defect density in the film. Other research works include those on a high-quality a-SiGe:H film fabricated by using the nanometer film forming/hydrogen plasma annealing method, modulated doping into multi-layer films of a-Si:H/a-Ge:H, and thin film transistor using very thin multi layer films of a-Si:H/a-Ge:H. 5 refs., 12 figs.

FY 1990 report on the results of the development of the entrained bed coal gasification power plant. Part 1. Element study; 1990 nendo seika hokokusho. Funryusho sekitan gaska hatsuden plant kaihatsu - Sono 1. Yoso kenkyu hen

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-03-01

For the purpose of establishing the technology of the integrated coal gasification combined cycle power generation, element study was made for a pilot plant of 200t/d entrained bed coal gasification power generation, and the FY 1990 results were summarized. In the study by the gasification test on 2t/d furnace, gasification test was conducted for the OM coal newly selected as a coal proposed for the expansion of coal kind. As a result, the pulverized coal/char of OM coal have almost good handling property and showed favorable gasification performance. In the study of large gas turbine combustor for demonstrative machine, with the aim of developing a combustor that makes stable combustion also in the low load region possible, fabrication of the accessory equipment of combustor (choke mechanism, measuring use duct and heat insulating plate) was made for the actual-pressure/actual-size combustion test. In the study by simulation of the total system of combined cycle power generation, etc., the following were conducted: verification of characteristics of the integrated control (state of the ordinary operation, state of the mock load control, etc.), load dump simulation (state of the bleed cooperation, state of the bleed separation (state of the air booster operation, etc.)), etc. (NEDO)

Report on the phase II R and D program of magneto-hydro-dynamics (MHD) electrical power generation. Prompt report by Electrotechnical Laboratory; Denji ryutai (MHD) hatsuden no dainiki kenkyu kaihatsu ni kansuru hokokusho. Densoken kenkyu sokuho

Energy Technology Data Exchange (ETDEWEB)

NONE

1989-07-28

This report summarizes results of the phase II R and D program of MHD electrical power generation (FY 1976 - 1983), which has been now completed. The phase II R and D efforts were concentrated on development of the durable power generation channels, where the designs and manufacture of the Mark II system were started, and the elementary techniques were simultaneously studied for, e.g., phenomena occurring around the electrodes, seed condensation and its effects on the electrode phenomena, and electrode and insulator materials for the power generation channels. The power generation channel was tested for its durability for a total of 430 hours, after it was incorporated in the Mark II system. The MHD power generation can incorporate direct combustion of coal, and will hold a dominant position in coal-fired power generation, which is expected to grow in the future. For this reason, the basic research schedules were revised in March, 1983, and the Mark II system was operated by firing a mixed fuel of kerosene and finely divided coal in a kerosene combustor, in line with the revised project, to understand the basic power generation characteristics with the combustion gases containing coal slag. (NEDO)

FY 2000 report on the results of the joint research - Field test project on the photovoltaic power generation for public facility use; 2000 nendo kyodokenkyu gyomu seika hokokusho. Kokyo shisetsu you taiyoko hatsuden field test jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-05-01

The paper arranged the FY 2000 results of the field test on the photovoltaic power generation for public facility use, etc. This report described in detail the results obtained at 237 places including the following: Social Welfare Corp. Seimei-kai, Kobe City (Hyogo Prefecture), Iitaka Town of Iinan County (Mie Prefecture), Kyushu Electric Safety Association, Educational Corp. Kongo Gakuen, Social Welfare Corp. Izumi-kai, Educational Corp. Shiobara Ikuei-kai, Educational Corp. Aiko Gakuen, Social Welfare Corp. Tachibana-kai, Cooperative Association Co-op Kobe, Social Welfare Corp. Hoshizuki-no-sato, Tochigi-Fuji Industrial Co., Hirabayashi Section of Gamo Town of Gamo County (Shiga Prefecture), Yanagawa City (Fukuoka Prefecture), Imadate City of Imadate County (Fukui Prefecture), Osaka Prefecture, Yamanashi Prefecture, Utazu Town of Ayauta County (Kagawa Prefecture), Educational Corp. Fukuyama Gakuen, New Energy Business Cooperative Association, Meitec Corp., Shikoku Medicom Co., Shizen Kobo Co., Educational Corp. Horikoshi Gakuen, Matama Town of Nishi-Kunisaki County (Oita Prefecture), Nio Town of Mitoyo County (Kagawa Prefecture), Educational Corp. Koshien Gakuin, Sansei Giken Co., Mitsui Greenland Co., AWI Mach Co., Nagoya City and Educational Corp. Kibogaoka Gakuen. (NEDO)

FY 1999 report on the results of the joint study - project on the industry use photovoltaic power generation field test. 2/3; 1999 nendo sangyonadoyo taiyoko hatsuden field test jigyo kyodo kenkyu seika hokokusho. 2/3

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-07-01

In the field test, solar cell panels were installed on rooftop, and inverters were installed indoors. The electric power generated was connected at high pressure with electric installation of facilities and was also supplied to power equipment, lighting, air conditioning, etc. in facilities. The FY 1999 results were summarized. The installation of photovoltaic power generation facilities at 38 places and the results of the study were summarized in this report including a new public office building of Nio town, Kagawa prefecture, General Welfare Center of Matsumae town, Ehime prefecture, General Culture Center of Nakajima town, Ehime prefecture, Educational Foundation Sugao School, Training Center of Japan Railway Co., etc. (NEDO)

FY1992 research report on the evaluation and analysis of data collected in fuel cell power generation field test project; 1992 nendo nenryo denchi hatsuden field test jigyo ni okeru shushu data hyoka kaiseki kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

This paper describes the achievements in fiscal 1992 in the field tests on fuel cell power generation systems. The three locations subjected to the present analysis are all installed with 50-kW systems, whereas power generation efficiency of around 35% such as 35.3, 34.2 and 34.6% was obtained when the systems were operated at the rated output. When the load gets to below a certain load band (about 30 kW), the power generation efficiency decreases proportionately with the load. The overall efficiency including heat supply was 77.8, 70.7 and 80.3% respectively at about the rated output, showing a trend that the higher the thermal efficiency, the higher the overall efficiency. The case of generating both electric power and heat simultaneously has higher efficiency than the case of heat supply alone. The contribution rate of the fuel cell as a base load was 2.8, 4.6 and 13.6%, respectively. The system with as high value as 13.6% takes a power load following type operation mode, in which power is generated during a time band with large load during weekdays, and no power is generated at nighttime and in holidays when load is smaller, playing a role of peak responding power supply. Only one trouble has occurred in an auxiliary generator in the heat recovery system. (NEDO)

Fiscal 1997 technological survey report. R and D on micromachine technology (Development of high functional maintenance technology for power station equipment); 1997 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho. Hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Activities were conducted in search of micromachine technology for a high functional maintenance system that inspects and repairs abnormal conditions such as cracks in a heat exchanger or a piping system without disassembling it in a power generating station such as a thermal or nuclear power plant. The activities were proceeded in four areas of (1) experimental manufacturing of the system (an inline self-running environment recognizing system, an external inspection system for fine tube group, and a system capable of light internal operation such as welding), (2) R and D on sophistication technology for functional devices, (3) R and D on common basic technologies, and (4) comprehensive investigation and research. In (1), examination of detailed basic specifications was carried out, as were examination of element technologies, experimental manufacturing and operation test of element devices, and performance evaluation. Further, a part of element devices was made on an experimental basis, with the basic functions demonstrated. In the comprehensive investigation and research, a trend in the future maintenance technology in power generating equipment was obtained and pigeonholed. (NEDO)

Achievement report for fiscal 1993 on developing entrained bed coal gasification power plant. Part 4. Pilot plant operation edition; 1993 nendo seika hokokusho. Funryusho sekitan gaska hatsuden plant kaihatsu - Sono 4. Pilot plant unten sosa hen

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-02-01

Tests and researches have been carried out on operation of a 200-t/d entrained bed coal gasification pilot plant built with an objective of establishing the coal gasification composite power generation technology. This paper summarizes the operation achievements in fiscal 1993. The plant operation record in fiscal 1993 was as follows: 430 hours 27 minutes in the gasification furnace (ten gasification operations), 233 hours 51 minutes in the gas refining facility, 140 hours 31 minutes in the gas turbine facility (power generation amount of 746.8 MWh with nine actuations), 1,263 hours 09 minutes in the processing furnace in the safety environment facility, and 427 hours 22 minutes in the NOx removal equipment. Descriptions were given with detailed graphs on the actuation and shutdown record with respect to the run D2, the run D3 (1 and 2), the run D4, the run D5, the run D6, and the run D7 (1 through 4). The operation procedures were prepared for the plant startup and shutdown schedule, the generalization report, the gasification furnace facility, the gas refining facility (dry type desulfurizing facility), the gas refining facility (dry type dust removing facility), the gas turbine facility, the combustor testing facility with actual pressure and size, and the safety environment facilities. (NEDO)

Research and development of evaluation system for photovoltaic power generation system. Research and development on evaluation technology of photovoltaic power generating systems; Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu. System hyoka gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on R and D of evaluation technology for photovoltaic power generating systems in fiscal 1994. (1) On preparation of test facility and measuring instrument, the pyrheliometer with a photovoltaic device as sensor was developed. (2) On collection and analysis of data, operation data of interconnection system, stand alone system, and water pump system were collected, and energy flow was analyzed. The following were also analyzed: time variation of a-Si solar cell modules, fluctuation correction factor of spectrum response, that of nonlinear response of crystalline solar cells, effect of solar radiation intensity and wind velocity on temperature rise of modules, and correction factor of DC circuit losses. (3) On on-site measurement technology, the array output measuring instrument was developed on the basis of capacitor charge system. (4) On simulation technology, simulation analyses of energy flow, optimum capacity of interconnection systems, correction factor of solar radiation, and capacity of array storage batteries were conducted. 3 figs., 6 tabs.

FY 1999 report on the results of the joint study - project on the industry use photovoltaic power generation field test. 1/3; 1999 nendo sangyonadoyo taiyoko hatsuden field test jigyo kyodo kenkyu seika hokokusho. 1/3

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-07-01

In the field test, solar cell panels were installed on rooftop, and inverters were installed indoors. The electric power generated was connected at high pressure with electric installation of facilities and was also supplied to power equipment, lighting, air conditioning, etc. in facilities. The FY 1999 results were summarized. The installation of photovoltaic power generation facilities at 88 places and the results of the study were summarized in this report including Social Welfare Corporation Seishoen, Maruto Co., Saga Sanyo Industries Co., Koyama Cranial Nerve Surgery/Internal Medicine Hospital, Tsuchiura Urban Development Co., Osaka Alloy Works, Suntory Limited, etc. (NEDO)

FY 1999 report on the results of the joint study - project on the industry use photovoltaic power generation field test. 3/3; 1999 nendo sangyonadoyo taiyoko hatsuden field test jigyo kyodo kenkyu seika hokokusho. 3/3

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-07-01

In the field test, solar cell panels were installed on rooftop, and inverters were installed indoors. The electric power generated was connected at high pressure with electric installation of facilities and was also supplied to power equipment, lighting, air conditioning, etc. in facilities. The FY 1999 results were summarized. The installation of photovoltaic power generation facilities at 39 places and the results of the study were summarized in this report including a community hall of Iwade town, Wakayama prefecture, Sugihara Industrial Co., a public library of Mabi town, Okayama prefecture, Social Welfare Corporation Shofukai Aiwaen, Japan Kodo Paper Industries Co., etc. (NEDO)

FY 1998 evaluation/analysis of the data collected in the field test project for photovoltaic power generation for public facilities; 1998 nendo kokyo shisetsu nadoyo taiyoko hatsuden field test jigyo ni okeru shushu data hyoka kaiseki

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In the field test project for the photovoltaic power generation for public facilities, operational data were collected/analyzed on facilities at 158 sites installed from FY 1994 to FY 1997. As a result, the following were found out: Average values of the global radiation on an inclined surface, equivalent array operation time, equivalent system operation time, system operation time, inverter performance efficiency, inverter load factor, array power coefficient, and system power coefficient are 3.51 kWh/m{sup 2}/D, 2.72 h/D, 2.47 h/D, 10.3 h/D, 0.91, 0.30, 0.77 and 0.70, respectively. No deterioration with age was recognized in the 4-year operation data. As to the maintenance, the item, 'there are a lot of failures in the photovoltaic power system,' was 2% in rate. As to the inspection, times are mostly once a month. The annual maintenance cost was widely between about 360 yen/kW and about 30,000 yen/kW. Supposing annual expenses to be a total of capital expense, direct expense, and general administrative expense, the power generation cost dropped from approximately 240 yen/kWh in FY 1994 to 100 yen/kWh in FY 1997. (NEDO)

Research report of fiscal 1997. Feasibility research on introduction of distributed power sources using new energy (photovoltaic and wind power generation) in the South Pacific; 1997 nendo chosa hokokusho. Minami Taiheiyo ni okeru shin energy (taiyoko, furyoku nado) wo katsuyoshita bunsangata dengen no donyu kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Feasibility research was made on distributed power sources using photovoltaic and wind power generation in Tonga and Samoa. For the best mix of environment-friendly power sources, hearing from government leaders and power business persons, and field inspection were carried out. Foreign currency earnings of Tonga are dependent on remittance from nations working overseas, while since diesel fuel for power generation is expensive because of import through Fiji and tariffs, multi-power sources for power cost reduction and low-cost new power systems are in expectation. Underground transmission and distribution lines are under consideration to prevent typhoon damages. Both countries are probably rich in wind power potential, however, wind condition data are poor requiring further researches. Tonga government is in charge of power business except that in Tongatapu island. In Samoa, EPC (Electric Power Corp.) is in charge of power business. Hydroelectric power generation is possible because of rivers formed by abundant tropical rains. Feasibility research was made on coal-firing, fuel cell combined, wind power, photovoltaic and waste power generation. 7 figs.

Introduction of new energies that gives vitality to town of Mano, industries, and people. Report on establishment of new energy vision in Mano Town area (Niigata Prefecture); Mano no machi, sangyo, hito ni katsuryoku wo ataeru shin energy no donyu. Manocho chiiki shin energy vision hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Based on assurance of energy availability in Sado Island, and age advancing of the population, an energy vision was established with the target of building 'Mano Town that seem real to everyone to find it good to live therein'. The population of Mano Town is about 6000 persons, and the energy consumption in total is 22,350 kl/year as converted into petroleum (industries and public sector at 12,162, households at 2,720, and transportation at 7,433). The new energy introduction is divided into three steps of the initial stage, middle stage, and long term stage. The initial stage will execute introduction of photovoltaic power generation into primary schools, promotion of utilization of solar energy at homes, promotion of introducing firewood and chaff boilers, and introduction of cogeneration into Yutoripia Mano. For the middle stage, discussions were given on introduction of photovoltaic power generation into the city office building, manufacture of light oil substituting fuel through rape seed and soy bean cultivation, introduction of hybrid automobiles, and manufacture of pellet fuel by utilizing wood wastes. For the long term stage, discussions were given on wind power generation, and ethanol fuel manufacture. (NEDO)

Research report for fiscal 1998. Basic research for promoting joint implementation of energy use rationalization in Chinese steel industry (examination of introduction of scrap preheating system for electric furnaces); 1998 nendo chosa hokokusho. Chugoku tekkogyo ni okeru energy no shiyo gorika (denkiro scrap yonetsu system donyu kento)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Investigations are conducted on a project of introducing a scrap preheating system based on the central insertion movable shaft design into China's electric furnaces for the sake of energy saving and global warming gas reduction. Of the electric furnaces numbering approximately 3400 now in operation in China, most are small and antiquated, and are extremely low in energy efficiency when in operation. The percentage of electricity supplied by coal-fired facilities is high, and this causes the CO2 reduction problem. Investigations are conducted into four steel mills operating electric furnaces, and examinations are made on the applicability of a preheating system, which is the ultimate batch system developed by Nippon Steel Corporation. Studies are conducted for Wuyang Iron and Steel Co., Ltd., Tianjin Steel Pipe Co., Ltd., Budong Iron and Steel Co., Ltd., and Shanghai Five Steel Co., Ltd., and it is found that greenhouse gas will be reduced by 31,000 tons, 21,000 tons, 13,000 tons, and 11,000-tons at the said mills, respectively. It is learned that the cost to be invested will be retrieved in approximately 2.5 years, 2.8 years, 7.7 years, and 8.0 years, respectively. It is concluded that Shanghai Budong Iron and Steel (Group) Co., Ltd., is the best candidate to be equipped with the above-said system. (NEDO)

Report on the survey in fiscal 1998. Basic survey on promotion of the joint implementation (a survey on improvement in wastes treatment system in Tapioka starch manufacturing plants); 1998 nendo chosa hokokusho. Kyodo jisshi nado suishin kiso chosa (Tapioka denpun kako kojo no haikibutsu shori no kaizen chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In order to promote the joint implementation based on COP3, a survey and a discussion were given on improvement in wastes treatment systems and reduction of greenhouse effect gas emission in Tapioka starch manufacturing plants scattered in Indonesia. Currently, the wastes are disposed untreated, discharging methane gas into atmosphere as a result of putrefaction and contamination. Ten factories were picked up as the object of the survey. The following processes are to be adopted as the most suitable method for treating waste water and waste substances: solids (peels and fibers) are composted, and rinsing waste water is subjected to simple aerobic treatment; purified waste water is recovered of methane gas by means of anaerobic treatment; and the reduction amount of greenhouse effect gas converted to CO2 is estimated to reach 314,824 tons per year in total of the ten factories. If the carbon dioxide discharge right can be transacted at a sales price of a dollar per ton, assuming the compost sales price at 200 Rp./kg, the IRR will be 10% or higher, making the project very highly profitable. An IRR of 8% may not be assured unless the discharge right can be sold at 5 dollars per ton if the compost sales price is 150 Rp./kg. The Indonesian Government expects financial assistance from Japan for the pilot plant demonstration. (NEDO)

Fiscal 1996 report on the results of the R and D of technology of high-level treatment/effective use of domestic/industrial wastes, etc. (for public); 1996 nendo Shin Energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku seikatsu sangyo haikibutsu shori yuko riyo gijutsu kenkyu kaihatsu seika hokokusho (kokaiyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

For the purpose of reducing environmental loads of waste and effectively using resource by waste recycling, a study was conducted of high-level treatment/effective use technology for domestic/industrial wastes, etc. The paper reported the results of fiscal 1996. In the EcoCement producing technology using the synthetic urban type waste, EcoCement with stable quality was obtained using sewage sludge and industrial waste as raw materials. In the specified freon decomposition disposal technology, an experiment was carried out on durability, etc. of the processing unit. In the high speed/reduced smell biological garbage disposal technology, technology of fermenting disposal, etc. were established, and at the same time technology of making garbage compost was developed. In the technology to manufacture environment friendly type plastic containers, etc., a degradation behavior was grasped of degradable plastics in the compost. In the spread type waste plastic/thermal recycle technology, studied were a system to collect waste and a system to make waste solid fuel. Technology to recycle coolant freon was studied. 14 refs., 261 figs., 137 tabs.

FY 1994 Report on the technical results. Research and development of micromachine technologies (Development of highly functional maintenance technologies for power plants); 1994 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho. Hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-01

This research and development project is aimed at development of the technologies for the micromachines provided with maintenance functions, e.g., for examination and maintenance of abnormal conditions in heat exchangers, piping systems or the like. The initial target is set at establishment of basic technologies for the micromachines, in consideration of the available technologies. The R and D activities are directed to (1) microcapsules for, e.g., micro power generators, (2) mother machines having controlling and instructing functions, (3) non-cabled examination modules, (4) cabled examination modules, and (5) total systems. The item (1) involves the micro power generators, and mechanisms of signal transmission, flaw finding and driving/suspension; the item (2) mechanisms of micro-optics and connection, group controlling, microbatteries, action type controlling, and artificial muscles; the item (3) expansion/contraction type transfer mechanisms, light energy supply, micro visual sensation, function connection, and concerted controlling; the item (4) tubular manipulators, and mechanisms of light-aided power generation and voltage elevation; and the item (5) maintenance and micromachine systems. (NEDO)

Fiscal 1994 achievement report. Development of entrained bed coal gasification power plant (Part 5 - Survey of demonstration plant); 1994 nendo seika hokokusho. Funryusho sekitan gaska hatsuden plant kaihatsu - Sono 5. Jissho plant ni kansuru chosa kenkyu hen

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-07-01

A survey was conducted of a demonstration plant for developing the technology of integrated coal gasification combined cycle power generation. In fiscal 1994, based on the studies of pilot plant operation conducted up to the preceding fiscal year and on the studies of a demonstration plant (conceptual design of a demonstration plant), systems were examined for still higher performance and economical efficiency. For optimizing the heat source for pulverized coal drying air, an extracted air heat utilizing system was adopted, excellent in performance (approximately 0.5% improvement in absolute value) and in economical efficiency. For reducing the consumption of inert gas for the fluidized bed desulfurization facility, an approximately 30% reduction was found to be possible dependent on gas regeneration conditions in the regeneration tower. For performance improvement with the combined cycle equipment placed under a partial load, the generating-end efficiency was improved approximately 0.2% when only SGC (syngas cooler) was loaded 80% or less and kept at a constant pressure. Studies were also made about how to maintain a constant output with the equipment exposed to air temperature changes. (NEDO)

Research and development of photovoltaic power system. Study of carrier dynamics in a-Si from optical and optoelectronic properties; Taiyoko hatsuden system no kenky kaihatsu. Amorphous silicon no koden tokusei to sono carrier dynamics no kogakuteki kenkyu

Energy Technology Data Exchange (ETDEWEB)

Hamakawa, K [Osaka University, Osaka (Japan). Faculty of Engineering Science

1994-12-01

This paper reports the result obtained during fiscal 1994 on research on an optical study of optoelectronic properties of amorphous silicon and its carrier dynamics. Studies have been performed on elucidation of the optoelectronic conversion mechanism in an a-Si film p-i-n junction system and the relationship of the mechanism with the optoelectronic properties. In the studies, optically induced defect level distribution was evaluated by using the modulated optical current spectroscopy, and confirmation was made on model forecast and qualitative agreement, such as large increase in neutral defect levels in association with beam irradiation. In research on elucidation of a film forming mechanism for a-Si based alloys, and material property control, a high-sensitivity reflective infrared spectroscopy was used to observe mechanisms such as treatments and processes given in device fabrication. In research on optical and optoelectronic properties of an s-Si alloy thin film by using the modulated spectroscopy, a new evaluation technology dealing with amorphous semiconductors was developed. The technology separately evaluates carrier migration factors of electrons and holes by combining polarization angle dependence of electro-absorption signals with hole migration measurements. 4 figs.

FY 2000 survey on technical trends. Survey of technical trends on materials for heightening of performance for power generation facility use; 2000 nendo gijutsu doko nado chosa. Hatsuden shisetsuyo koseinoka zairyo ni kakawaru gijutsu doko nado chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

As to high performance/high function plastic materials used in power generation facilities, technical trends were surveyed on the recycle situation and recycle R and D to study the subjects to be solved. For wire covering materials, vinyl chloride, polyethylene, rubber, etc. are used, and the recycle of resin has not been advanced. Concerning the generation of waste plastic, the existence of a lot of plastics different in characteristics makes the recycle difficult. As to the use of waste plastic as resource, the material recycle and recovery of combustion energy are being made, but only a part of the plastic is reused as chemical raw materials. Relating to the R and D of the chemical recycle technology, there are sample studies on the pyrolysis of polyolefine, dechlorination of chlorine base resins, etc. Recently, the following have been made public: proposal of depolymerization monomer based on the cyclic monomer, study of liquefaction of approximately 100% of the thermosetting resin, approach to the solvolysis by supercritical solvent. (NEDO)

Fiscal 1999 research cooperation project. Research cooperation on community-oriented practical photovoltaic power systems (Practical methane gas fermentation fuel cell power systems); 1999 nendo metan hakko gas nenryo denchi hatsuden system no jitsuyoka ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This report describes the research cooperation with developing countries on practical methane gas fermentation fuel cell power systems in 1999-2002. This research aims to construct the methane gas fermentation fuel cell power facility using livestock excreta which can supply power to the facility and peripheral areas. The facility controls various substance concentrations in waste water within environmental standards, and uses waste as compost. This project is very promising in use of environment-friendly energy, effective use of unused energy and power supply to unelectrified areas for China under serious conditions such as rapid increase in energy demand and various environment problems. There are such various issues to achieve this target as securing livestock (pig breeders) and excreta, and fermentation and recovery of suitable methane gas necessary for fuel cell power systems from excreta. This report is composed of 2 parts, (1) Current use of energy resources and use of unused energy in Guangdong province, and (2) Technical requirements for practical methane gas fermentation fuel cell power systems. (NEDO)

Report on research and development achievements in fiscal 1980 in Sunshine Project. Development of a total flow electric power plant(Two-phase rotation inflator); 1980 nendo total flow hatsuden plant no kaihatsu seika hokokusho. Niso kaiten bochoki

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

Out of the development of a total flow power plant in the Sunshine Project, this paper describes a two-phase rotatry inflator. It reports the achievements in fiscal 1980. It is intended to utilize effectively the energy of gas-liquid two-phase fluid (containing a great amount of hot water) often seen in geothermal resources in Japan. Therefore, development is considered on a two-phase rotary inflator as a total flow power generation technology to inflate the gas-liquid fluid as it is without performing separation thereof, and convert it to an external work to draw out output. The inflator is a volume type rotary engine, which has the highest efficiency theoretically, but has not been put into practical use worldwide. Based on the result obtained in the previous fiscal year, development is made on a most suitable seal to be applied to circumferential seal of an external rotor, apex seal, and intake port seal. A rotary inflation performance testing machine is fabricated to study inflation of the gas-liquid two-phase fluid. Setting the engine efficiency of 60% or higher as the target, detailed design, fabrication and assembly shall be completed on two-phase rotation inflators of volume type and self-rotation type of 300 kW class. (NEDO)

FY 1998 Report on development of large-scale wind power generation systems. Research of wind turbines for storm worthy and easy construction; 1998 nendo ogata furyoku hatsuden system kaihatsu. Taikyofu kensetsu yoigata fusha ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The research and development statuses in various countries are surveyed, to have useful information to draw the future R and D directions for wind turbines resistant to storms and easy construction. Greece has sites suitable for wind power generation in mountainous districts, and is developing the systems while taking the characteristic weather conditions into consideration. The country provides information regarding aerodynamic/structural design methods for wind turbine blades applicable to turbulent wind generated by complex terrain, and wind assessment and analyses in complex terrain. In India, on-the-spot surveys are made at the cyclone-attacked wind farms. One of the areas on which the USA is putting emphasis is development of small-size wind turbines and wind-diesel hybrid systems for developing countries and independent grid systems in remote areas. Australia is constructing wind-diesel hybrid systems to be connected to a number of independent grid systems in its western area. In Europe, information is collected for the advanced aerodynamic analysis, construction of offshore wind turbines, and production engineering and facilities for blades and other components from Vestas and N.E.G. Micon as the leading wind turbine makers. (NEDO)

Achievement report on commissioned research of R and D in fiscal 2000 on micromachine technologies. Development of high function maintenance technology for power generation facilities; 2000 nendo kenkyu seika hokokusho. Hatsuden shisetsu you kokino mentenansu gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

R and D has been carried out on a high function maintenance system that performs inspection and repair of anomalies such as internal cracks by using micromachines without need of disassembling heat exchangers and piping systems in power generation facilities. This paper summarizes the achievements in fiscal 2000. In the research of a prototype self-propelled system to recognize environment in tubes, the secondary prototype system integrating all of the elemental devices was fabricated, and its functions were verified. In the research of a prototype system to inspect outer surface of fine tube groups, a plurality of single machines that perform movement in narrow spaces on flat surface, interlocking, separation and flaw detection were connected to execute a vertical movement experiment. In the research of a prototype system for works internal to devices, fabrication and functional verification were conducted on the final prototype system which is equipped with functions of measuring very small nicks and performing repair works, which are mounted on the tip of a curved tube unit with multiple degrees of freedom. In the research of a functional device improving technology, a device that puts together artificial muscles, micro-joints, and a suspension device with very low friction was fabricated, and a functional verification was implemented thereon. (NEDO)

Survey report for fiscal 1998 on the survey on preparation of data collection related to new energy technology development (wind power generation ); 1998 nendo shin energy gijutsu kaihatsu kankei data shu sakusei chosa (furyoku hatsuden) chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

As a result of heightening consciousness on assurance of energy security and global environment problems in recent years, it is urged in Japan to promote development of technologies to introduce and proliferate new energies, and work on acceleration of the introduction. On the other hand, in order to move forward effectively the introduction promoting project intended of proliferation and enlightenment, it is necessary to put into order comprehensively and systematically the different data on the new energies, and summarize them as the basic data. This report, focusing on a wind power generation system, collects and puts into order the latest published data on the wind power generation system, placing in the center the introduction examples in Japan and other countries, supporting measures, wind power generation system markets, and the specifications of major windmills. The major contents may be summarized as follows: significance of introducing the wind power generation system, the current status of the market, policies in different countries, status of introducing the system in other countries, subsidy institutions for the introduction, the introduction flow, efforts made by government related organizations and local governments, a list of window offices of the related corporations, the fundamental knowledge, and the movements in 1998. (NEDO)

Research and development of evaluation system for photovoltaic power generation system. Research and development of evaluation systems for photovoltaic cells and modules; Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu. Taiyo denchi hyoka system no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on R and D of the evaluation system for solar cells in fiscal 1994. (1) On development of the performance evaluation method for solar cells, data collection, analysis and measurement of atmospheric conditions necessary for outdoor measurement were carried out to improve the measurement accuracy of laminated solar cells. The validity of measurement methods was verified by comparing experimental results with outdoor measurement ones to improve the indoor measurement accuracy by multiple light source solar simulator. Generated energy in solar cell module level was also studied in field. (2) On development of the reliability evaluation method for solar cells, deterioration data were collected and analyzed by long-term exposure test. As a result, it was clarified that Pmax values are directly affected by seasonal change in air mass, and deterioration of solar cells is hardly found after exposure test for one year, showing a stable state. The characteristic recovery experiment of amorphous solar cell modules was carried out, and the accelerated deterioration test method of thin film cell modules was also studied. 2 figs.

Research and development of evaluation system for photovoltaic power generation system. Survey on research and development of solar cell evaluation system; Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu. Taiyo denchi hyoka system no kenkyu kaihatsu chosa

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the survey results on R and D of solar cell evaluation systems in fiscal 1994. The performance/reliability evaluation subcommittee continuously analyzed technical issues and discussed solution measures from the last fiscal year. On development of performance evaluation methods, improvement of measurement accuracy for laminated solar cells is the study issue to be solved. Although laminated solar cells are measured by multiple light source solar simulator, difficult spectrum compensation causes measurement errors. Collection and analysis of data for determining atmospheric conditions, and outdoor measurement experiment under the atmospheric conditions for reference solar light were carried out. The study on incident angle characteristics of laminated solar cells clarified that the deviation from COS characteristics is 1.0% or less at an incident angle of 30{degree}. The study on generated energy in solar cell module level in field clarified that generated energy and generation efficiency are proportional to intensity of solar radiation. 1 tab.

Survey report for fiscal 1998 on the conversion of the existing coal burning power plant to natural gas burning plant in Sakhalin State; 1998 nendo Saharinshu muke, kisetsu sekitandaki hatsuden no tennen gas daki tenkan chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The present survey is intended to discuss a modernization plan effective in reducing greenhouse effect gases for the two existing coal burning power plants in Sakhalin Island, Sakhalin State, the Federal Republic of Russia. The power plants are Sakhalinskaya Power Plant (GRES) and Yuzhno Sakalinskaya Power Plant (TETs-1). Simultaneously with converting the fuel from coal to natural gas, discussions are given on an optimal plan including introduction of the combined cycle and repowering technologies aiming at improving the thermal efficiency. Reduction in greenhouse effect gases, finance, and economy are evaluated. At the same time, verification will be given on environment improvement in Sakhalin Island, and influence on sustainable economic and social activation. The GRES modernization plan intends to build four combined cycle units each of 80 MW class to have nearly the same total capacity as the current total power generation facility capacity (315 MW). The TETs-1 modernization plan will convert the fuel for the existing boilers from coal to natural gas, modify one of the boilers whose construction is being suspended into gas burning boiler, and add gas turbines. (NEDO)

Fiscal 1996 survey report. Data collection and evaluation analysis in the project on field tests on the fuel cell generation; 1996 nendo kenkyu hokokusho. Nenryo denchi hatsuden field test jigyo ni okeru data shuyaku oyobi hyoka kaiseki

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The paper installed fuel cell power generation equipment experimentally at various facilities which are the final diffusion form of the new energy power generation, conducted long-term operation under the actual load, collected/analyzed various data, arranged them as data useful for full scale introduction/diffusion, aiming at forming the base for general diffusion of the fuel cell power generation. The number of the systems installed for field test execution has been 24 places/28 units since the start of the project, and the system capacity totaled 4,250kW. The actual operation hours in five years are 6,000-28,000. In fiscal 1996, the average cumulative accumulated operational rate was approximately 68%, a little over that in fiscal 1995, 65%. The average load factor was 69% in fiscal 1995 and 70% in fiscal 1996. The utilization rate increased as a whole to about 57% on average if seeing only fiscal 1996, as compared with that in fiscal 1995, about 48%. The power generating efficiency was approximately 34% on average. As to the status of shutdown of the fuel cell power generation, the paper surveyed the average interval of failure, the rate of frequency of shutdown, the analysis of shutdown, etc. 250 figs., 29 tabs.

Achievement report on contract research. Large-scale project - Results of 1st-phase research and development of MHD power generation system; Plant system no hyoka. Ogata project dai 1 ki MHD hatsuden system kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1976-03-01

Described in detail involving the results of component development, assessment, and the indication of problems are the power generation channel, superconductive magnets and a helium refrigeration and liquefaction unit, seeds collector, heat exchanger, combustor, etc. Described involving the result and effect of power generation system research and development and the indication of problems is the research on Mark V and Mark VI operation tests. Described in relation to thermal performance calculation, economic effectiveness calculation, and environmental conservation involving an MHD (magnetohydrodynamic) power plant are the combustion of heavy oil, combustion of natural gas, plant having a 1,000MW power generator as its base load, control of NOx and sulfur in MHD power generation, etc. As for planning for the next stage, the configuration of a 10MW MHD power generation plant, its equipment, construction cost, and preliminary element research, etc., are described. Furthermore, propositions are presented concerning future plans and the prospect of commercial MHD power generators, technological ripple effects due to MHD power generation research and development, and research and development in the future. (NEDO)

Report on achievements in fiscal 1998. Development of technologies to put photovoltaic power generation systems into practical use - Development of solar beam power generation and utilization systems and ancillary technologies (Research and development of new building material integrated solar cell modules - investigation and research on analysis of practical application); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (shinkenzai ittaigata taiyo denchi module no kenkyu kaihatsu (jitsuyoka kaiseki ni kansuru chosa kenkyu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In order to promote the research to put new building material integrated solar cell modules into practical use, the following items were investigated: (1) functions and specifications for harmonizing with buildings, (2) new module materials that can respond to building materials, (3) marketability, (4) standardization of the assessment methods, (5) consistency with relevant legislation and related institutions, (6) effects on environment as building materials, and (7) investigation on technological trends inside and outside the country. In Item (1), the significance of developing the new building material integrated solar cell modules was made clear. In Item (2), the performance requirements on the currently used module materials were put into order. In Item (3), the market size was investigated, and assignments to establishing the market were put into order, such as the distribution and construction institutions, and assistance to the system introduction. In Item (4), standardization and unification of the assessment methods were discussed, and the items to be standardized were extracted. In Item (6), LCA on the currently used modules was performed. In Item (7), participation was made to the second solar beam power generation conference and EUROSUN '98; investigations were made on trends of developing the new building material integrated solar cell modules and how the recycling related legislation is being progressed; and the achievements in the development activities were confirmed, and the assignments were investigated at the new building material integrated solar cell module subcommittee. (NEDO)

FY 2000 report on the results of the development of commercialization technology of the photovoltaic power system. R and D of the photovoltaic power generation utilization system/periphery technology (R and D of the new solar cell module integrated with construction materials - Investigative study on analysis for commercialization); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu, Taiyoko hatsuden riyo system, shuhen gijutsu no kenkyu kaihatsu (Shinkenzai ittaigata taiyodenchi mojuru no kenkyu kaihatsu - Jitsuyoka kaiseki ni kansuru chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of supporting the study for commercialization of the new module integrated with construction materials, survey of the technical trend of the new module integrated with construction materials in Japan and abroad was conducted, and the FY 2000 results were summarized. As to the module material correspondent to construction materials, the results of the survey made in the past three years were summarized, and the subjects to be considered in future were arranged from a viewpoint of disposal/recycle of modules. Concerning the marketability, various policies for the spread of solar cell module that is an immature good were arranged. Survey was also made of the photovoltaic power system using the field test project as a sample, and the following were made clear: The photovoltaic power generation has appeal for environmental consideration and energy conservation; In some cases, the power generation effect was not as much as expected because the information on design/construction is not sufficient. Relating to the evaluation of its effect on the environment, the paper summarized the environmental influence in each of the module methods at each stage of production/utilization/disposal and the basic items for measures to cope with the influence. (NEDO)

Fiscal 1974 Sunshine Project result report. R and D on photovoltaic power generation system (R and D on new type solar cells); 1974 nendo taiyoko hatsuden system no kenkyu kaihatsu seika hokokusho. Shingatashiki taiyo denchi no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-05-27

This report summarizes the fiscal 1974 research result on R and D of new type solar cells, which includes researches on (1) solar cell structure, (2) packaging, and (3) improvement of a conversion efficiency. In the 1st research, theoretical study was made on the relation between a solar cell efficiency and various design factors to obtain basic data for ordinary cell structure and vertical junction type cell structure. As impurity source, a thermal diffusion method using doped oxide by CVD was compared with that using boron nitride, resulting in no difference in solar cell characteristics between both methods. The measurement results on contact resistances of Al, Fe and Ni with electrodes prepared by electron beam deposition showed that these materials are applicable to Si more than 10{sup 18}/cm{sup 3} in impurity density as electrode materials. In the 2nd research, exposure tests were made on some kinds of specimens, resulting in no troubles. Study was made on production costs and structures suitable for automatic production of 4 kinds of packages with different basic structures. In the 3rd research, the prototype solar cell was prepared to use under solar radiation within 20SUNS. (NEDO)

Fiscal 1995 achievement report. Development of entrained bed coal gasification power plant (Part 1 - Studies of key elements and techniques); 1995 nendo seika hokokusho. Funryusho sekitan gaska hatsuden plant kaihatsu - Sono 1. Youso kenkyu hen, gijutsu chosa hen

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Element techniques were studied and surveyed for establishing the technology of integrated coal gasification combined cycle. In fiscal 1995, E coal (coal of high ash fluid point) gasification was tested in the 2 tons/day furnace for the effect of its properties on furnace operation and for its properties relating to gasification and slagging and for changes in such properties due to flux admixed with the E coal. It was then found that the ash fluid point was so high as 1500 degrees C and that flux admixing, recovered oxygen reinjection, etc., would be necessary for the assurance of stable slag discharge. In a study using combined cycle system simulation, a comparison was made between results from tests conducted on a real system and results from the simulation, based on the detailed model completed by the preceding fiscal year. The model was reviewed and improved, and simulations were conducted in the respective operating states and operating modes. In the survey of element techniques, information was gathered at a Japan-U.S. joint technical conference held in Japan in October this year. Studies were also made about technical guidelines, or the like, involving coal gasification power generation. (NEDO)

Fiscal 1974 Sunshine Project result report. R and D on photovoltaic power generation system (R and D on Si ribbon crystal horizontal pulling method); 1974 nendo taiyoko hatsuden system seika hokokusho. Silicon yokohiki ribbon kessho no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-05-01

The ribbon crystal horizontal pulling process first supplies Si melt from a continuous Si material supply equipment to a pulling bath which is formed by a quartz crucible and heater. Supplied melt is heated by the pulling bath heater to keep its molten condition. The pulling bath is piled up to the top rim of the quartz crucible by supplied melt, forming the liquid surface of the pulling bath. A plane crystal seed is contacted with melt nearly horizontally. A crystal growth layer is formed at the solid-liquid interface of the contact part of the seed by controlling a heat control equipment and bath heating power. Non-dendrite growth is better in crystal quality than the others. Among non-dendrite growth methods, a horizontal pulling method is more excellent in fast pulling of wider ribbon crystals than a vertical one. Among horizontal pulling methods, Toyo Silicon Co.' method discharges heat into gas phase by using free surface including the vicinity of the seed as cooling surface, while Bleil method uses a solid heat sink for heat release, resulting in slower crystal growth. (NEDO)

Basic investigation on promotion of joint implementation in fiscal 2000. Efficiency improvement project for gas turbine power plant in Iran; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Iran gas turbine hatsuden plant no koritsu kaizen project

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Investigations and discussions have been given on measures to improve energy conservation and efficiency at a power plant of Kish Water and Power Company (KWPC) in Iran. The site has high ambient temperature throughout a year, making the gas turbine power plant capable of generating power only at about 70% of the rated output, with the power generation efficiency decreasing. The project has analyzed the current situation at the plant, and evaluated different means that appear effective in improving the efficiency, including the gas turbine absorbed air cooling system, the steam injection system, and the combined cycle. As a result of the discussions, it was revealed that energy saving effect can be obtained at 145 TJ with the gas turbine absorbed air cooling system, 224 TJ with the steam injection system, and 1017 TJ with the combined cycle. The annual reduction of greenhouse gas emission due to the above energy conservation would be about 11 thousand tons, 16.5 thousand tons, and 75 thousand tons, respectively. However, the investment payback period would be about 2.45 years, 8.31 years, and 14.21 years, respectively. Therefore, the profitability does not appear very attractive because of low fuel unit cost. (NEDO)

Fiscal 1976 Sunshine Project result report. R and D on photovoltaic power generation system (R and D on new type solar cell); 1976 nendo taiyoko hatsuden system no kenkyu kaihatsu seika hokokusho. Shingatashiki taiyo denchi no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1977-05-30

This report describes the fiscal 1976 research result on new type solar cells for photovoltaic power systems. On junction formation, the solar cell fabricated by spray coating showed output characteristics equivalent to that by rotary coating or phase diffusion, and inexpensive coating liquid, 1/40 of commercially available liquid in price, showed a sufficient result, however, the conversion efficiency of P{sup +}/N elements was insufficient. Schottky barrier polycrystal Si thin film was suitable for large-area elements without any property degradation. Small grain boundary density of polycrystal layers was also necessary. Temperature characteristics of collector element structure with a comb electrode were calculated theoretically. Change in diffusion length of minority carriers due to temperature well agreed between measured and calculated ones. Optimization calculation was also carried out. The size, curve, weight and transmissivity of plastic and glass materials for solar cell packaging were evaluated by continuous outdoor exposure tests. Fluorinated ethylene-propylene, methyl methacrylate and polycarbonate plates and glass were the most promising materials because of less deformation. (NEDO)

Achievement report for fiscal 1996 on the research and development of micromachine technology. Development of advanced-function maintenance technology for power generation facilities; 1996 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho. Hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Technologies for integrating functions are studied for a self-propelled surroundings recognition system that travels in a small-diameter tube at power generation facilities. Parameters are analyzed, and piezoelectric locomotion devices are reduced in size. A disk shape microantenna is experimentally built and evaluated, which is for realizing energy supply and communication by means of microwaves. Studies are conducted to improve the performance of optical energy transmission devices and to realize their systematization. Basic specifications are established for the embodiment of CCD (charge coupled device) microcameras to be installed. A high-efficiency, high-reliability micromachine system is constructed, in which multiple machines coordinate with each other for the exterior inspection of groups of small-diameter tubes. Devices which are capable of driving, deceleration, and propulsion prove to be feasible. Basic specifications are established for microconnectors to connect, separate, and combine multiple machines as occasion calls. Also discussed is the development of a micromachine for tube interior check and repair which operates making use of the inspection hole enabling tube interior check and repair without the need of disassembling the equipment to be repaired.

Research and development of evaluation system for photovoltaic power generation system. Research and survey on test and evaluation method for BOS component devices; Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu. Shuhen gijutsu hyoka system no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on R and D of the evaluation method for BOS component devices in fiscal 1994. (1) On the study on requirements of BOS component devices for practical use, the study results on storage battery, inverter, protective device for system interconnection, and effective use means for storage battery were summarized. On the future device technology, it was clarified that the following value added technologies are promising: simple design of inverter circuit, cost reduction by common specification and mass production, and stabilization of voltage and compensation of momentary peak load by combining inverter with small-capacity storage batteries. (2) On the study on the performance test method for BOS component devices, basic characteristic (capacity, efficiency) test, PSOC charge/discharge cycle test, and accelerated life cycle test were performed for 4 kinds of new storage batteries developed by NEDO. The whole characteristic test results satisfied specifications, and long-term cycle test is in promotion for all new storage batteries. 3 figs., 4 tabs.

Achievement report for fiscal 1997 (New Sunshine Project) on the development of superconductor power application technology. Research on a total system / investigative research on introduction effects; 1997 nendo chodendo denryoku oyo gijutsu kaihatsu (New Sunshine keikaku) seika hokokusho. Total system nado no kenkyu / donyu koka no chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper describes investigation and discussion on effects of introducing a superconductor power application technology. The generator sub-committee has compared features, technical problems and development expenses in the first and second proposals, but has not reached the final conclusion. The first proposal is targeted for early realization of 200-300 MW class generators with development cost of six to seven billion yen and a development term of seven years. These developments raise largely towards practical application the levels of material technologies, fabrication and processing technologies, and analysis and design technologies. The second proposal is intended of developing 200-300 MW class generators targeted for increased diameter, as a reduced size machine of a 600-MW generator being a future generator. It will take development cost of eight to nine billion yen with the period of nine years for the development. Majority of the technologies required for developing the future 600-MW class generator can be demonstrated. The AC superconductor device sub-committee has investigated design examples, clarified the specification requirements, and investigated and studied the development measures. The oxide superconductor sub-committee has investigated and studied making wires and conductors, and device application feasibility, but has not reached the stage of presenting specific research and development methods. The practical application strategy sub-committee has also not been able to present a collective measure because of difficulty of making future prospect on the electric power business. (NEDO)

Report on survey in fiscal 2000. Survey on introduction of external accreditation system in engineer education - iron and steel (Survey on education accreditation in material field); 2000 nendo chosa hokokusho. Gijutsusha kyoiku no gaibu ninteiseido donyu ni kansuru chosa (tekko) -Zairyo bunya ni okeru kyoiku nintei ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In order to ensure international applicability of engineer education such as in universities and other organizations, and to improve the environment to supply human resources demanded by economic societies, a survey was performed on external accreditation systems for engineer education such as in universities and other organizations in the material field. In the survey, discussions were given on whether or not the education program accreditation system for the material field being structured has any problem in the actual operation of the accreditation through trials at Chiba Engineering University and Tokai University. As a result, it was revealed that the criteria are too general, requiring more detailed description on the guideline, and criteria should be so considered that assessment at higher levels can be given to the graduation research, which is a Japan's particular education system. In addition, it was made clear as a problem in the education programming side that a room for improvement remains in the education methods for the engineering ethics, communication skills, and the method for evaluating the students' achievements. In the survey on the methods for examination and accreditation in the U.S.A. it was found out that education organizations are perplexed with the new criteria of EC 2000. (NEDO)

FY 1998 survey report. Feasibility study of the new energy introduction/spread policy application (Study of the model project conception using natural energy utilization technology); 1998 nendo chosa hokokusho. Shin energy donyu fukyu hosaku tekiyo kanosei chosa (shizen energy riyo gijutsu wo katsuyoshita model jigyo koso no kento)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This survey clarified the problems about that consumers and various kinds of group do not come to tackle independently and positively the use of natural energy and the solutions, and studied the necessity of the model project to enlighten the society on those concretely and widely. The model project conception is to spread/settle various kinds of natural energy by making them linked with the regional economic growth and resource/environment problems in a community with a regional autonomous body as a unit. There, new incentives to be made toward the promotion/spread of natural energy are presented such as the construction of an energy self-supporting society which is closed-cycle by using various kinds of energy combinedly and compositely, the formation of ideas for adding values except kWh value to electric power generated by natural energy, etc. Besides, about the conception of model project, the training facility function and demonstration exhibition function for the purpose of education/enlightenment are also added in consideration of the importance of natural energy that general citizens should feel close to themselves. (NEDO)

Report on the fiscal 1993 investigational study of the environmental technology development trend in Japan. Trend survey of the introduction policy of environmentally friendly products; 1993 nendo Nippon ni okeru kankyo gijutsu kaihatsu doko nado ni kansuru chosa kenkyu hokokusho. Kankyo chowagata seihin no donyu hosaku nado doko chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-05-01

An investigation was conducted into the systematical scheme for the introduction and promotion of environmentally friendly products mostly to the U.S., Europe and China. In the U.S., the introduction policy is given to one and all fields of the industry. The introduction policy of the U.S. has a characteristic that the introduction is left to the market principle by DSM or permit dealing, etc. except the preferential tax system and systematical finance in which the government is concerned. The policy of European countries is characterized by the idea preceding, standards or rules are first given, and the whole is pushed on to them. Accordingly, it seems that there is few atmosphere of expecting to receive the government side economic incentives from the corporate side. Legal regulations on the environment in China were prepared in a comparatively early time (1979), but the supervision of obeying the regulations and the appearance/spread of environmentally friendly product menus have just started. Accordingly, as the introduction policy on environmentally friendly products, there was found nothing valuable but the regulations. 12 refs., 3 figs., 15 tabs.

Research report of FY 1997 on the environmentally acceptable coal utilization system introduction support project. Demonstration project of circulating fluidized bed boiler (Jinzhou Coal-Thermal Power Corporation); 1997 nendo seika hokokusho (kankyo chowagata sekitan riyo system donyu shien jigyo). Junkan ryudosho boiler ni kakawaru jissho jigyo (Jinzhou netsuden sokoji)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

To verify the clean coal technology to be diffused in China and consolidate its diffusion basis, demonstration project of circulating fluidized bed boiler was conducted through the cooperation with China which is positive in its introduction. This report describes its characteristics. Coal and limestone are supplied in a lower part of combustion chamber, and are mixed with circulating ash by fluidized air for combustion. Densely fluidized bed the same as the bubbling fluidized bed is formed in the lower part of combustion chamber, which provides excellent stability in ignition and combustion. Particles including ash, char and limestone formed during the combustion are discharged into the cyclone through the convection heat transfer part at the outlet of combustion chamber with the combustion gas flow. Since the gas temperature is lowered to 400 to 500degC at the convection heat transfer part, troubles of the ash circulating system can be prevented. The combustion gas separated from ash at the cyclone is discharged through the heat exchanger and precipitator, and the collected ash is returned to the lower part of combustion chamber. In FY 1997, design, fabrication, procurement/inspection, field survey/meeting, survey of visitors/meeting, and education were carried out. 4 figs., 4 tabs.

Fiscal 1998 research report on the demand forecast of rare element minerals, recycling technology of rare elements from waste, and substitute rare element minerals; 1998 nendo chosa hokokusho. Kisho genso koseki no juyo yosoku, kisho genso no haikibutsu kara no kaishu gijutsu oyobi daitai kisho genso koseki nado ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Rare element mineral is indispensable material for functionalization of high-tech raw materials. Its deposit is poor, an increase in its future demand is expected, and its information disclosure is insufficient because of strategic important material. To solve these problems, the following were studied systematically, and urgent research themes on rare element minerals were clarified: (1) High-efficiency recycling technology of rare elements, (2) Waste treatment system after recycling of rare elements from the viewpoint of environmental measures, (3) Establishment of the database of rare element minerals, and development of new substitute rare element minerals, and (4) Design method of substitute materials possible to generate various existing functions without any rare elements. Among them, in particular, precise separation of 46 kinds of rare elements from waste of high-tech raw materials, and recycling of rare elements from zinc refining waste and pyrite ore deposit containing copper were pointed out as important themes. (NEDO)

FY 1999 report on the results of the contract project 'The model project for facilities for effective utilization of industrial waste at the industrial complex in Thailand.' Separate Volume 4 - FY 1999 project; 1999 nendo seika hokokusho. Tai ni okeru kogyo danchi sangyo haikibutsu yuko riyo setsubi moderu jigyo - 4

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of reducing the consumption of fossil fuel by recycling industrial waste for effective use as petroleum substituting energy in Thailand where the amount of industrial waste is expected to increase, a model project on facilities for effective use of industrial waste at the industrial complex was carried out, and the FY 1999 results were reported. Concretely, the industrial waste generated from each plant at the industrial complex owned by IEAT is to be incinerated in fluidized bed incinerator, and the process steam is to be generated by recovering waste heat by waste heat recovery boiler and to be supplied to plants within the complex. In this fiscal year, the first year of the project, the attachment to the agreement was prepared in terms of the allotment of the project work between Japan and Thailand, various kinds of gist, schedules, etc. and signed. After that, the following were conducted at the Japan side according to the attachment to the agreement: determination of the basic specifications for facilities, basic design, detailed design, manufacture of a part of the equipment, etc. Separate Volume 4 included the results of the inspection of the tank, pump, blower, etc. (NEDO)

FY 1999 report on the results of the contract project 'The model project for facilities for effective utilization of industrial waste at the industrial complex in Thailand.' Separate Volume 6 - FY 1999 project; 1999 nendo seika hokokusho. Tai ni okeru kogyo danchi sangyo haikibutsu yuko riyo setsubi moderu jigyo - 6

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of reducing the consumption of fossil fuel by recycling industrial waste for effective use as petroleum substituting energy in Thailand where the amount of industrial waste is expected to increase, a model project on facilities for effective use of industrial waste at the industrial complex was carried out, and the FY 1999 results were reported. Concretely, the industrial waste generated from each plant at the industrial complex owned by IEAT is to be incinerated in fluidized bed incinerator, and the process steam is to be generated by recovering waste heat by waste heat recovery boiler and to be supplied to plants within the complex. In this fiscal year, the first year of the project, the attachment to the agreement was prepared in terms of the allotment of the project work between Japan and Thailand, various kinds of gist, schedules, etc. and signed. After that, the following were conducted at the Japan side according to the attachment to the agreement: determination of the basic specifications for facilities, basic design, detailed design, manufacture of a part of the equipment, etc. Separate Volume 6 included drawings of assembling of the equipment such as crane, crusher and valve. (NEDO)

Achievement report for fiscal 1993 on developing entrained bed coal gasification power plant. Part 1. Element research and technology survey edition; 1993 nendo seika hokokusho. Funryusho sekitan gaska hatsuden plant kaihatsu - Sono 1. Youso kenkyu hen, gijutsu chosa hen

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-02-01

With an objective of establishing a coal gasification composite power generation technology, R and D works have been carried out on elementary technologies. This paper summarizes the achievements in fiscal 1993. In the research on the slag utilization technology, discussions were given on the applicability of slag discharged from a 200 t/d pilot plant to fine aggregate for concrete. In the research on a large gas turbine combustor for a demonstration plant, the test conditions were discussed and the reliability of the combustor was analyzed to conduct an actual gas combustion test using the coal D in continuation from the test in the previous fiscal year. In the research on the simulation of a composite power generation system, the simulation models were reviewed and corrected. Load variation simulations were carried out on every operation mode to have conducted comparison with and discussion on the actual plant data. In order to clarify the slagging phenomenon in the 200 t/d pilot plant, a characteristics test was performed by using a 2 t/d furnace. As a result, the combustor ash load and the dynamic pressure in the axial direction in the throat section were presumed to be the large factors for the occurrence of slagging. (NEDO)

Reports on 1979 result of Sunshine Project. Testing research for detailed design of solar thermal power generation plant (tower converging method); 1979 nendo taiyonetsu hatsuden plant (tower shuko hoshiki) no shosai sekkei no tame no shiken kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-03-31

This report briefly describes first, in the summary of the results, the contents of the research results of the year with the outcome as the central point. Then, it explains in detail, in the contents of the research, the substance of each research item, results, their examination contents, and future research subjects. The objective of the research is, for the purpose of technically seeking the cost performance of a solar thermal power generation plant, (1) to develop equipment constituting the plant and (2) to develop a pilot plant having an electrical output of about 1,000kW at the peak by the tower converging method. The research results were as follows. (1) In the confirming test of a heliostat test unit, the final conclusion was obtained of the wind resistance calculated value by the wind tunnel test of the heliostat; the design materials of the assembly jigs were obtained; the data of the operation forecast was obtained in a tracking test; and a sensor was developed for the tracking instrumentation. (2) In the confirming test of the improved absorbing surface/mirror, the improvement/trial production including the manufacturing method was carried out as the absorbing surface for the actual unit. (3) In the heat collecting test, steam generation and a loop control test were performed. (4) The plant system was analyzed, with data obtained for the operating method. (NEDO)

FY 1992 report on the results of the commissioned research and development project. R and D of SOFC (solid oxide fuel cells); 1992 nendo nenryo denchi hatsuden gijutsu kaihatsu seika hokokusho. SOFC kotai denkaishitsugata nenryo denchi no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-05-01

The research and development project is carried out for fuel cell power generation technologies and solid electrolyte type fuel cells, and the reports on the FY 1992 results issued by the participant organizations are summarized. For R and D of the modules, Fuji Electric conducted the R and D for the large-area, cell-stacked type, and Sanyo Electric for the composite cell-stacked type. For R and D of the materials and fundamental technologies, Fine Ceramics Center is conducted the R and D for microscopic structures of the electrode, Fujikura for electrode structures produced by spraying or the like, Mitsubishi Heavy Industries for multi-functional fuel electrodes, Murata Seisakusho for co-sintering technologies, and Mitsui Shipbuilding for current collecting technologies. For R and D of the systems, Central Research Institute of Electric Power Industry conducted the R and D for the systems, Electric Power Development and Mitsubishi Heavy Industries jointly for designs of the cell peripheries, and the Japan Research and Development Center for Metals for elementary technologies for the peripheral devices. (NEDO)

Fiscal 1997 research report on the data collection, evaluation and analysis in the PV power generation field test project for public facilities; 1997 nendo kokyo shisetsu nado yo taiyoko hatsuden field test jigyo ni okeru shushu data hyoka kaiseki

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

As a part of the field test project for diffusing PV power generation into public facilities generally, evaluation and analysis were made on the collected data from 105 sites installed during fiscal 1993-1996. Analysis of operation characteristics was made by using parameters obtained by developing a basic equation for every component. 94% of all the sites fell under the total solar irradiation of 3.0- 4.5kWh/m{sup 2}/D. 83% of those fell under the equivalent array operation time of 2.5-4.0h/D. 70% of those fell under the equivalent system operation time of 2.5-3.5h/D. 72% of those fell under the system operation time of 9.0-12.0h/D. 78% of those fell under the effective inverter efficiency of 0.84- 0.96. 68% of those fell under the inverter load factor of 0.25-0.35. 85% of those fell under the array performance ratio of 0.7-1.0. 83% of those fell under the system performance ratio of 0.6-0.9. The generation cost decreased from 270yen/kWh in 1993 to 100yen/kWh in 1996 because reduction of an installation cost largely contributed to reduction of the total cost. (NEDO)

Achievement report for fiscal 1989. Research and development of ceramic gas turbine (Portable regenerative two-shaft radial turbine for electric power generation); 1989 nendo ceramic gas turbine no kenkyu kaihatsu seika hokokusho. Kahanshiki hatsuden'yo saisei nijikushiki radial turbine

Energy Technology Data Exchange (ETDEWEB)

NONE

1990-05-01

Research and development has been advanced on a ceramic gas turbine with an output of 300-kW class, and having thermal efficiency of 42% or higher. Activities were performed in the following three fields: 1) research of heat resistant ceramic members, 2) research of elementary technologies, and 3) studies on design, prototype fabrication, and operation. In Item 1, forming and sintering were performed on a scroll of large size difficult for forming, an output turbine nozzle, a gas generator turbine nozzle, a shroud and back-shroud for same to extract technological problems. In addition, discussions were given on a method to bond the rotor of the gas generator turbine with the shaft. In Item 2, elementary tests were given on the rotary heat-storage type heat exchanger which has high relative technological difficulty and requires a great amount of time for development, wherein the thermal efficiency was improved by improving the flow velocity distribution. Furthermore, a combustor for the metal gas turbine was developed. Specifications were established for a test device required for hot spin tests of the gas generator turbine and output turbine, and part of the device was fabricated. In Item 3, detailed design was made for the metallic basic-type gas turbine to become the master form of the turbine to be developed. (NEDO)

Development in fiscal 1999 of technology to put photovoltaic power generation system into practical use. Management of research and development (System development committee working group); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Kenkyu kaihatsu kanri (system kaihatsu bukai)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

This paper reports activities carried out in fiscal 1999 by the system development committee working group, a subordinate organization of the committee for development of the photovoltaic power generation technology. The items of implementation laid with emphasis in the current fiscal year included deliberations on the research achievements of the projects completed in fiscal 1999, on the research achievements of the new projects during fiscal 1999, and on pre-final evaluation of the development of a technology to put photovoltaic power generation system into practical use. The themes on the progresses in fiscal 1999 reported in March 2000 consisted of the followings: research and development of a system evaluation technology, investigation and research on supply capability evaluation on the photovoltaic power generation system, researches on peripheral devices for AC modules, investigation and research on electric safety of the photovoltaic power generation system, investigation and research on long-term reliability of inverters, investigation and research on meteorological data for optimal design, investigation and research on evaluation of the photovoltaic power generation, research on a photovoltaic power generating multi-hybrid system, research on a high-density linkage technology, and demonstrative research on a solar beam micro-hydraulic hybrid system. (NEDO)

FY 1999 Report on research and development of power generation by solid electrolyte fuel cell. Research and development of solid electrolyte fuel cell; 1999 nendo nenryo denchi hatsuden gijutsu kaihatsu kotai denkaishitsugata nenryo denchi no kenkyu kaihatsu kenkyu seika

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-06-01

This project is aimed at establishment of the module basic technology and commercialization of the solid electrolyte fuel cell in the early stage by designing, construction, operation and performance evaluation of a several kW-class module which incorporates the cylindrical cell fabricated by the wet process. The FY 1999 R and D efforts include (1) cell performance demonstration study: the cylindrical single cell fabricated by the wet process is demonstration-tested to determine the initial performance and durability for continuous operation, thereby comparing the external reforming with internal reforming in output, with the internal reforming rate as the parameter, (2) development of a several kW-class module: the adequate cell arrangement structure within the module is studied by the computer-aided simulation, and the tests for confirming thermal cycle durability of the modified bundle are conducted using the module power generation unit and the several kW-class module is tested, and (3) development of the technology for designing a thermally supported module: the effects of, e.g., air and fuel supply conditions on the module performance are analyzed using the analytical model as the base. Expansion of the module level to the process simulation model has been completed, based on these results. (NEDO)

Fiscal 1995 achievement report. Development of entrained bed coal gasification power plant (Part 3 - Pilot plant operational test - 2/2); 1995 nendo seika hokokusho. Funryusho sekitan gaska hatsuden plant kaihatsu - Sono 3. Pilot plant unten shiken hen (2/2)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The 200 tons/day entrained bed coal gasification pilot plant constructed for establishing the technology of integrated coal gasification combined cycle was subjected to operational tests, and the fiscal 1995 results are detailed. During Runs D13, D14, E1, D15, and A14 in the operational test of the gas clean-up facility (dry type dedusting facility), 10 troubles occurred, including damage of the separator screen, leak in the seal valve, and leak of the expansion gas, and measures were taken to deal with each of the troubles. The results of the gas turbine facility operational test were satisfactory, without any trouble worth discussion. In the operational test of the safety/environment-related facility, it was found that the produced gas was stably incinerated and that denitration performance during gas turbine operation roughly achieved the intended level. In the operational test of electric and control facilities, an overall test was conducted, inspection was made of the indoor switching facility, etc., and 13 improvements were made, which included the alteration of the high ANN setting in the water tank for slag, the alteration of the mill exit temperature setting for enabling the use of Taiheiyo coal, and proper methods for carrying out high-load operation. (NEDO)

FY 1993 report on the results of the commissioned research and development project. R and D of SOFC (solid oxide fuel cells); 1983 nendo nenryo denchi hatsuden gijutsu kaihatsu seika hokokusho. SOFC kotai denkaishitsugata nenryo denchi no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-05-01

The research and development project is carried out for fuel cell power generation technologies and solid electrolyte type fuel cells, and the reports on the FY 1993 results issued by the participant organizations are summarized. For R and D of the modules, Fuji Electric conducted the R and D for the large-area, cell-stacked type, and Sanyo Electric for the composite cell-stacked type. For R and D of the materials and fundamental technologies, Fine Ceramics Center conducted the R and D for microscopic structures of the electrode, Fujikura for electrode structures produced by spraying or the like, Mitsubishi Heavy Industries for multi-functional fuel electrodes, Murata Seisakusho for co-sintering technologies, and Mitsui Shipbuilding for current collecting technologies. For R and D of the systems, Central Research Institute of Electric Power Industry conducted the R and D for the systems, Electric Power Development and Mitsubishi Heavy Industries jointly for designs of the cell peripheries, and the Japan Research and Development Center for Metals for elementary technologies for the peripheral devices. (NEDO)

Fiscal 1995 achievement report. Development of entrained bed coal gasification power plant (Part 5 - Surveys and studies of demonstration plant); 1995 nendo seika hokokusho. Funryusho sekitan gaska hatsuden plant kaihatsu - Sono 5. Jissho plant ni kansuru chosa kenkyu hen

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Surveys and studies were conducted concerning a demonstration plant for establishing the technology of integrated coal gasification combined cycle, and the fiscal 1995 results are compiled. In this fiscal year, a demonstration plant conceptual design was prepared for assuring smooth transition from a pilot plant to a commercial plant. The design followed the system employed at the Nakoso pilot plant for its gasification power generation. It was decided that the gasification furnace be of the air-blown (oxygen enriched) 2-stage entrained bed type, that the desulfurization system be of the dry type 2-stage fluidized bed type, the dedusting system be of the dry type granular bed type (moving bed type), that the combined cycle power facility be derived from the commercialized gas turbine, and that the cycle of the steam system agree with the integrated coal gasification combined cycle system now under discussion. Studies were made, which covered heat efficiency (generating end/sending end), heat/matter balance, process flow, gas turbine/steam system optimization, comparison in performance with a pilot plant with its dimensions increased, estimation of the performance of each of the facilities, estimation of the construction cost, calculation of the generation cost, environmental friendliness, operating characteristics, acceptable coal types, and the like. (NEDO)

Fiscal 1996 comprehensive report on R and D on advanced chemical processing technology; 1996 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu sokatsu hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu / sekiyu seisan system fushoku boshi gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

R and D was conducted on technology for composite thin film formation such as laser MOCVD, for thin film lamination, and for synthesis reaction and characterization in compounded fields where temperature/pressure/magnetic field/electrical field, etc., are compounded, for the purpose of creating materials with functions newly added or reinforced by regulating compositions and structures through atomic/molecular orders. The R and D was conducted on 24 themes, which were rearranged into four categories. Examples of the themes are as follows; development of super hard permanent magnets by crystallization process control of Nd-Fe-B amorphous alloys, as for structural control technology; research on high functional thin film sensors (PbLaTiO{sub 3}) using laser MOCVD, and research on ultra thin film by multi-ion-beam sputtering with ion/photo irradiation, as for thin film technology; R and D on highly ordered structure control technology in electrode surface compounded reaction fields, as for compounded fields; and, research on diagnostic technique for compounded reaction fields by laser-ionization method, as for supporting technologies. (NEDO)

Research cooperation project in fiscal 2001. Research cooperation on putting into practical use of district complying type photovoltaic power generation system; 2001 nendo kenkyu kyoryoku jigyo. Chiiki tekigo gata taiyoko hatsuden system tou no jitsuyoka ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

Research cooperation has been performed with an intention of establishing technologies to develop a design program for photovoltaic power generation systems suitable for the diverse natural and social conditions in China, the performance inspections and quality enhancement thereon. This paper summarizes the achievements in fiscal 2001. For installing the photovoltaic power generation system, procurement, transportation and installation were carried out in Gansu Province for a 8.4 kW integrated system and in Qinghai Province for 10 kW and 12 kW integrated systems. Visits were made to the sites to confirm the operating conditions, and maintenance and management conditions of the systems having been installed to date. With regard to performance evaluation devices of the cells and modules, some pieces of the equipment were repaired and re-adjusted, and training for using them was executed. Eight persons have visited Japan from China and participated in the training in Japan for utilization and operation of the photovoltaic power generation systems for the persons involved in the system operation. In addition, in order to determine the future information exchange directions, workshops were held with PV experts and manufacturers participating from Japan to exchange items of information. (NEDO)

Fiscal 1996 achievement report. Development of entrained bed coal gasification power plant (Part 1 - Studies of dismantling and surveys of techniques); 1995 nendo seika hokokusho. Funryusho sekitan gaska hatsuden plant kaihatsu - Sono 1. Kaitai kenkyu hen, gijutsu chosa hen

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-01-01

For the establishment of technology of integrated coal gasification combined cycle, studies were made for the dismantling of the 200 tons/day entrained bed coal gasification pilot plant and surveys were conducted of overseas technologies. In the gasification furnace facility, 40 devices were selected, and dismantled, from the locations corresponding to the factors of damage expected to occur involving important equipment. Although no significant damage was detected in the gasification pressure vessel, peripheral walls, or the like, malfunctions due to corrosion or abrasion were discovered in some pipes and members. In the dry type gas clean-up facility (desulfurization facility), damage due to heat stress or corrosion was detected in the regeneration tower inner cyclone, regeneration tower filter flexible tubes, and in circulation gas cooler cooling tubes. In the dry type gas clean-up facility (dedusting facility), damage was found in the dust collector gas seal valve, dust collector filter materials cut valve, and in the separator A/B. In the gas turbine facility, no abnormality was discovered but for some damage in some initial stage static vanes. (NEDO)

Research and development of photovoltaic power system. Characterization and control of surface/interface recombination velocity of crystalline silicon thin films; Taiyoko hatsuden system no kenkyu kaihatsu. Silicon kessho usumaku ni okeru hyomen kaimen saiketsugo sokudo no hyoka to seigyo

Energy Technology Data Exchange (ETDEWEB)

Hasegawa, H [Hokkaido University, Sapporo (Japan). Faculty of Engineering

1994-12-01

This paper reports the result obtained during fiscal 1994 on characterization and control of surface/interface recombination velocity of crystalline silicon thin films. To optimize design and manufacture of solar cells, it is necessary to identify correctly resistance factor (or doping) of bulk of materials, bulk minority carrier life, and recombination velocity on surface, passivation interface and electrode interface. A group in the Hokkaido University has been working since a few years ago on development of non-contact and non-destructive photo-luminescence surface level spectroscopy (PLS{sup 3}). A new non-contact C-V method was also introduced. Using these methods, basic discussions were given on possibility of separate measurements on surface/interface and bulk characteristics of solar cell materials. The PLS{sup 3} method and the non-contact C-V method were used for experimental discussions on evaluation of silicon mono-crystalline and poly-crystalline materials. Discussions were given on separate evaluations by using the DLTS method. 10 figs., 2 tabs.

Fiscal 1995 survey of promotion of the geothermal development. Report on a usage feasibility test of a small scale geothermal binary cycle power generation system; 1995 nendo chinetsu kaihatsu sokushin chosa. Chusho chinetsu binary hatsuden system jissho shiken hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

In this survey, studies for popularization and practical utilization of small and medium size geothermal binary cycle power systems which assesses low and medium temperature geothermal resources were conducted, and studies for development of the system to be introduced for practical use and for promotion of the popularization were made. A study was carried out of preconditions and various conditions of a demonstrative test plant (100kW class, 500kW class) in view of the initial cost of the actual plant, and an analysis was made of the power generation cost. Acceptability of the demonstrative test plant (100kW class) was examined to analyze problems on the introduction. A thermodynamic analysis was made of the output of geothermal binary cycle power generation. Analysis/evaluation of the results of the 100kW demonstrative test plant were carried out in view of the operation results of the plant of the same kind, and checks/reviews were conducted of performance and reliability of the system, equipment simplification, etc. Inspection of the system was made in the stage of design/manufacture of the 500kW demonstrative test plant. Concerning the spread/expansion of the system, studied were multiple stage geothermal utilization and PR promotion method. 14 refs., 62 figs., 55 tabs.

Fiscal 1974 Sunshine Project result report. R and D on solar heat power generation system (R and D on curved reflector light collection system); 1974 nendo taiyonetsu hatsuden system no kenkyu kaihatsu seika hokokusho. kyokumen shuko hoshiki system no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-05-30

This report composed of 6 parts summarizes the fiscal 1974 Sunshine Project research result on the solar heat power generation system with a curved reflector light collection system. Part 1 outlines the research target, research result and research system. Part 2 describes each research item in detail. This part on system and hardware researches is composed of (1) study on 1,000kW system, (2) development of plane/parabolic reflector light collection equipment, (3) development of parabolic reflector light collection equipment, (4) development of selective transparent membrane and selective absorption surface, and (5) study on heat storage equipment and heat exchange equipment. Part 3 describes the future R and D plan for every year focusing the fiscal 1975 R and D plan. Part 4 describes various cooperative activities with other research groups such as various committees related to the Sunshine Project, universities and Electrotechnical Laboratory. Part 5 describes several patents produced during this R and D. Part 6 summarizes the results on this R and D. (NEDO)

FY 1977 Annual report on Sunshine Project results. Experimental research for detailed designs of tower light-collection type solar thermal power plant; 1977 nendo taiyonetsu hatsuden plant (tower shuko hoshiki) no shosai sekkei no tame no shiken kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1978-03-31

This project is aimed at pursuing technical and economic possibilities of solar thermal power plant by development of devices for a tower light-collecting type solar thermal power plant (in particular, heliostat, heat absorber and heat storage device) and materials therefor through the basic tests, and tests using a 10 kW heat collector and construction, on a trial basis, of a large-scale model plant with a commercial heliostat, and by planning to construct a 1,000 kW-class pilot plant for generating peak-shaving power using these devices. The major achievements in the FY1977 are summarized. The system analysis estimates annual power production possibly reaching 547,600 kWH. The heat-collecting test plant records a heat-collecting efficiency of 50 to 70% for collected heat quantity of 50 kW or more. The heliostat test confirms that the GL type is more favorable than the XY type. The heat absorber, which is a 1/3 model of the commercial device, is tested for its heat releasing performance, producing the quantitative released heat data. The heat transfer characteristics are investigated for the regenerative heat exchanger when the phase changes occur simultaneously on both molten salt and water sides. The mirror is exposure-tested in the field test for 1 year, to collect the data. (NEDO)

Analysis and evaluation for practical application of photovoltaic power generation system. Research and development of elemental technologies for thin-type solar cells; Taiyoko hatsuden system jitsuyoka no tame no kaiseki hyoka. Usugata takessho taiyo denchi jitsuyoka no tame no kaiseki hyoka

Energy Technology Data Exchange (ETDEWEB)

Sekikawa, T; Shimokawa, R; Yui, N; Takato, H; Takahashi, T; Ishii, K; Suzuki, E; Nagai, K; Kawanami, H; Tanimoto, J; Sakuta, H; Iwata, Y; Saito, N; Koyama, K; Sawada, S [Electrotechnical Laboratory, Tsukuba (Japan)

1994-12-01

Described herein are the results of the FY1994 research program for analysis and evaluation for thin substrate polycrystalline solar cells. In order to analyze the structures of the grain boundaries in and interfaces with the cell substrate, and their effects on electrical activity, the photoluminescence (PL) measurement which enables spectroscopic analysis is applied to electromagnetically cast Si crystals. There are good correlations among PL luminous intensity, MBIC output and dislocation density for the grain boundary which contains many strains and serves as the dislocation source, because carriers in such a grain boundary easily disappear to reduce its luminous intensity at the band ends. Concrete scenarios for realizing thin-film silicon solar cells of high efficiency are presented, based on the analysis of the light-contained thin-film silicon solar cells of high output current, made in the previous year on a trial basis. An alumina substrate of high reflectivity is produced by the experiments of combining various devices. It is expected to realize high output current for the thin-film solar cells. 3 figs.

FY 1992 report on the results of the development of an entrained bed coal gasification power plant. Part 4. Operation of pilot plant; 1992 nendo seika hokokusho. Funryusho sekitan gaska hatsuden plant kaihatsu - Sono 4. Pilot plant unten sosa hen

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-02-01

A record was summarized of the operation test study in FY 1992 of the 200 t/d entrained bed coal gasification pilot plant that was constructed with the aim of establishing technology of the integrated coal gasification combined cycle power generation. The operating hour of gasifier facilities in FY 1992 was 635 hours 19 minutes, and the number of times of gasification operation was 9. The operating hour of letting gas through to gas refining facilities was 549 hours 14 minutes. The operating hour of gas turbine facilities was 310 hours 18 minutes, and the generated output was 1,366.2 MWh. The operating hour of treatment furnace of safety environment facilities was 1,401 hours 4 minutes, and that of the denitrification system was 621 hours 24 minutes. As to the actual results of the start-up/stop, the paper detailedly recorded those of RUNs 10, 11, 12, 13 and D1. Further, operation manuals were made for the schedule of plant start-up/stop, gasifier facilities, gas refining facilities (dry desulfurization facilities), gas refining facilities (dry dedusting facilities), actual pressure/actual size combustor testing facilities and safety environment facilities. (NEDO)