WorldWideScience

Sample records for gsm network design

  1. Mobile network maintenance (GSM)

    CERN Multimedia

    IT Department

    2009-01-01

    Maintenance work will be carried out on the CERN mobile network infrastructure (GSM) on the 23 and 24 July from 6 p.m. to 6 a.m. in order to replace discontinued equipment and to increase the bandwidth capacity of the GSM mobile network. All CERN GSM emitters (40 units) will be moved one by one to the new infrastructure during the maintenance. The call of a user connected to an emitter at the time of its maintenance will be cut off. However, the general overlapping of the GSM radio coverage should mean that users are able immediately to call again should their call be interrupted. IT/CS/CS

  2. Design and Research of a New secure Authentication Protocol in GSM networks

    Directory of Open Access Journals (Sweden)

    Qi Ai-qin

    2016-01-01

    Full Text Available As the first line of defense in the security application system, Authentication is an important security service. Its typical scheme is challenge/response mechanism and this scheme which is simple-structured and easy to realize has been used worldwide. But these protocols have many following problems In the GSM networks such as the leakage of user indentity privacy, no security protection between home registers and foreign registers and the vicious intruders’ information stealing and so on. This paper presents an authentication protocol in GSM networks based on maths operation and modular square root technique . The analysis of the security and performance has also been done. The results show that it is more robust and secure compared to the previous agreements.

  3. Building GSM network in extreme conditions

    Science.gov (United States)

    Mikulec, M.; Voznak, M.; Fajkus, M.; Partila, P.; Tovarek, J.; Chmelikova, Z.

    2015-05-01

    The paper is focused on the building ad-hoc GSM network based on open source software and low-cost hardware. The created Base Transmission Station can be deployed and put into operation in a few minutes in a required area to ensure private communication between connected GSM mobile terminals. The convergence between BTS station and the other networks is possible through IP network. The paper tries to define connection parameters to provide sufficient quality of voice service between the GSM network and IP Multimedia Subsystem. The paper brings practical results of voice call quality measurement between users inside BTS station mobile network and users inside IP Multimedia Subsystem network. The calls are simulated by low-cost embedded solution for speech quality measurement in GSM network. This tool is under development of our laboratory and allows automatic speech quality measurement of any GSM or UMTS mobile network. The Perceptual Evaluation of Speech Quality method is used to get final comparable results. The communication between BTS station and connected networks has to be secured against the interception from the third party. The influence of the securing method for quality of service is presented in detail. Paper, apart from the quality of service measurement section, describes technical requirements for successful interconnection between BTS and IMS networks. The authentication, authorization and accounting methods in roaming between BTS and IMS system are presented too.

  4. Secure communication interface design for IoT applications, using the GSM network

    OpenAIRE

    Wightwick, Andrew; Halak, Basel

    2016-01-01

    In this work, a secure short messaging service (SMS)-based communication interface is designed. The interface has applications in the internet of things (IoT) such as machine to machine (M2M) communications, and human-operated remote system management. The case study of waking a personal computer remotely is considered, and a complete proof-of-conceptis implemented for this purpose, using a field-programmable gate array (FPGA)-based receiving device and an Androidbased transmitting device. On...

  5. Design and Implementation of a Web-based Greenhouse Remote Monitoring System with Zigbee Protocol and GSM Network

    Directory of Open Access Journals (Sweden)

    Abdolhamid Tabatabaeifar

    2014-10-01

    Full Text Available In modern and big greenhouses, it is necessary to measure several climate parameters to automate and control the greenhouse properly. Monitoring and transmitting by cable may lead to an expensive and stiff measurement system. Since, Wireless Sensor Network (WSN is a distributed system that consists of small-size wireless sensor nodes equipped with radio and one or several sensors; it is a low cost option to build the required monitoring system. In this paper, we introduce and implement an intelligent monitoring system based on WSN by using Xbee modules. The Xbee Series 2 hardware uses a microchip from Ember Networks that enables several different flavors of standards-based ZigBee mesh networking. All gathered information by sensors, are sent to a remote center in form of GPRS packets through a GSM network and viewed by monitoring software. The proposed system has low power consumption, low cost and simple driver circuits. Furthermore, it can support various types of digital and analog sensors.

  6. Gsm Networks: A Review Of Security Threats And Mitigation Measures

    African Journals Online (AJOL)

    Gsm Networks: A Review Of Security Threats And Mitigation Measures. ... Information Manager (The) ... This paper investigates the security measures used in GSM networks which include Authentication, Encryption, Equipment Identification and Subscriber Identity Confidentiality, as well as the manifestation of network ...

  7. UMTS network planning, optimization, and inter-operation with GSM

    CERN Document Server

    Rahnema, Moe

    2008-01-01

    UMTS Network Planning, Optimization, and Inter-Operation with GSM is an accessible, one-stop reference to help engineers effectively reduce the time and costs involved in UMTS deployment and optimization. Rahnema includes detailed coverage from both a theoretical and practical perspective on the planning and optimization aspects of UMTS, and a number of other new techniques to help operators get the most out of their networks. Provides an end-to-end perspective, from network design to optimizationIncorporates the hands-on experiences of numerous researchersSingle

  8. TRACKING VEHICLE IN GSM NETWORK TO SUPPORT INTELLIGENT TRANSPORTATION SYSTEMS

    Directory of Open Access Journals (Sweden)

    Z. Koppanyi

    2012-07-01

    Full Text Available The penetration of GSM capable devices is very high, especially in Europe. To exploit the potential of turning these mobile devices into dynamic data acquisition nodes that provides valuable data for Intelligent Transportation Systems (ITS, position information is needed. The paper describes the basic operation principles of the GSM system and provides an overview on the existing methods for deriving location data in the network. A novel positioning solution is presented that rely on handover (HO zone measurements; the zone geometry properties are also discussed. A new concept of HO zone sequence recognition is introduced that involves application of Probabilistic Deterministic Finite State Automata (PDFA. Both the potential commercial applications and the use of the derived position data in ITS is discussed for tracking vehicles and monitoring traffic flow. As a practical cutting edge example, the integration possibility of the technology in the SafeTRIP platform (developed in an EC FP7 project is presented.

  9. Design of Remote Monitoring System of Irrigation based on GSM and ZigBee Technology

    Science.gov (United States)

    Xiao xi, Zheng; Fang, Zhao; Shuaifei, Shao

    2018-03-01

    To solve the problems of low level of irrigation and waste of water resources, a remote monitoring system for farmland irrigation based on GSM communication technology and ZigBee technology was designed. The system is composed of sensors, GSM communication module, ZigBee module, host computer, valve and so on. The system detects and closes the pump and the electromagnetic valve according to the need of the system, and transmits the monitoring information to the host computer or the user’s Mobile phone through the GSM communication network. Experiments show that the system has low power consumption, friendly man-machine interface, convenient and simple. It can monitor agricultural environment remotely and control related irrigation equipment at any time and place, and can better meet the needs of remote monitoring of farmland irrigation.

  10. Artificial Neural Network model for the determination of GSM Rxlevel from atmospheric parameters

    Directory of Open Access Journals (Sweden)

    Julia Ofure Eichie

    2017-04-01

    Full Text Available Accurate received signal level (Rxlevel values are useful for mobile telecommunication network planning. Rxlevel is affected by the dynamics of the atmosphere through which it propagates. Adequate knowledge of the prevailing atmospheric conditions in an environment is essential for proper network planning. However most of the existing GSM received signal determination model are function of distance between point of signal reception and transmitting site thus necessitating the development of a model that involve the use of atmospheric parameters in the determination of received GSM signal level. In this paper, a three stage approach was used in the development of the model using some atmospheric parameters such as atmospheric temperature, relative humidity and dew point. The selected and easily measurable atmospheric parameters were used as input parameters in developing two new models for computing the Rxlevel of GSM signal using a three-step approach. Data acquisition and pre-processing serves as the first stage and formulation of ANN design and the development of parametric model for the Rxlevel using ANN synaptic weights form the second stage of the proposed approach. The third stage involves the use of ANN weight and bias values, and network architecture in the development of the model equation. In evaluating the performance of the proposed models, network parameters were varied and the results obtained using mean squared error (MSE as performance measure showed the developed model with 33 neurons in the hidden layer and tansig activation, function in both the hidden and output layers as the optimal model with least MSE value of 0.056. Thus showing that the developed model has an acceptable accuracy value as demonstrated from comparison of results with actual measured values.

  11. Remote controlled gate controller using a GSM network and Arduino platform

    Directory of Open Access Journals (Sweden)

    Pospisilik Martin

    2016-01-01

    Full Text Available Most remote controllers for entrance gates operate on free frequencies 433 or 868 MHz. However, this technology limits the user comfort, as it is usually not common that bi-directional communication is established. A higher comfort of controlling the entrance gates can be achieved by employing the GSM network for transmission of commands and messages between the gate controller and the user. In this case, only a conventional GSM cellular phone is needed to control the gate. A description of such a controller based on the GSM module and Arduino controller is provided in this paper.

  12. Performance Analysis of Gsm Networks in Minna Metropolis of Nigeria

    African Journals Online (AJOL)

    The performance of a cellular network is assessed in terms of key performance indicators (KPI) based on statistics generated from drive tests or network management systems. However, drive tests give the 'feel' of the designed network as it is experienced by the subscribers. Therefore, it is used in this study to compare ...

  13. Reengineering GSM/GPRS Towards a Dedicated Network for Massive Smart Metering

    DEFF Research Database (Denmark)

    Madueño, Germán Corrales; Stefanovic, Cedomir; Popovski, Petar

    2014-01-01

    of smart meters will require reliable, long-lived wide area connections. This motivates to investigate the potential of GSM to be evolved into a dedicated network for smart metering. We introduce simple mechanisms to reengineer the access control in GSM. The result is a system that offers excellent support...... for smart metering, as well as the other massive machine-to-machine traffic patterns that are envisioned in 3GPP.......GSM is a synonym for a major success in wireless technology, achieving widespread use and high technology maturity. However, its future is questionable, as many stakeholders indicate that the GSM spectrum should be re-farmed for LTE. On the other hand, the advent of smart grid and the ubiquity...

  14. Class-E Amplifier Design Improvements for GSM Frequencies

    Directory of Open Access Journals (Sweden)

    Z. Nadir

    2011-06-01

    Full Text Available Efficient power amplifiers are essential in portable battery-operated systems such as mobile phones. Also, the power amplifier (PA is the most power-consuming building block in the transmitter of a portable system. This paper investigates how the efficiency of the power amplifier (which is beneficial for multiple applications in communcation sector can be improved by increasing the efficiency of switching mode class E power amplifiers for frequencies of 900 MHz and 1800 MHz. The paper tackles modeling, design improvements and verification through simulation for higher efficiencies. This is the continuation of previous work by the authors. These nonlinear power amplifiers can only amplify constant-envelope RF signals without introducing significant distortion. Mobile systems such as Advanced Mobile Phone System (AMPS and Global System for Mobile communications (GSM use modulation schemes which generate constant amplitude RF outputs in order to use efficient but nonlinear power amplifiers. Improvements in designs are suggested and higher efficiencies are achieved, to the tune of 67.1% (for 900 MHz and 67.0% (1800 MHz.

  15. Quality-of-Service differentiation in an integrated services GSM/GPRS network

    NARCIS (Netherlands)

    Litjens, R.; Boucherie, Richardus J.

    2001-01-01

    We develop and analyse a generic model for performance evaluation, parameter optimisation and dimensioning in a \\textsc{gsm}/\\textsc{gprs} network. The model enables analytical evaluation for a scenario of integrated speech, video and data services, potentially offered in distinct priority classes.

  16. Efficient Radio Resource Allocation in a GSM and GPRS Cellular Network

    Directory of Open Access Journals (Sweden)

    David Vannucci

    2004-10-01

    Full Text Available This paper investigates the effect of various radio resource allocation strategies in a GSM/GPRS cellular network. The most efficient resource allocation is analysed as a function of the proportion of circuit switched voice and packet switched data load. The Grade of Service and average packet delay is investigated as a function of the load, packet size and call duration. Additionally, the feasibility of using voice over Internet Protocol as opposed to circuit switched voice is investigated as a means to increase subscriber capacity per base station. The work is motivated firstly by the complexity of having both circuit switched and packet switched connectivity on GSM/GPRS mobile cellular system and secondly that an exclusively packet based access on GSM/GPRS has the potential to increase the efficiency of resource utilisation by suitably varying the channel allocation to exploit the characteristics of voice and data traffic.

  17. Design and Implementation of GSM Based Automated Home Security System

    Directory of Open Access Journals (Sweden)

    Love Aggarwal

    2014-05-01

    Full Text Available The Automated Home Security System aims at building a security system for common households using GSM modem, sensors and microcontroller. Since many years, impeccable security system has been the prime need of every man who owns a house. The increasing crime rate has further pressed the need for it. Our system is an initiative in this direction. The system provides security function by monitoring the surroundings at home for intruders, fire, gas leakages etc. using sensors and issue alerts to the owners and local authorities by using GSM via SMS. It provides the automation function as it can control (On/Off the various home appliances while the owners are away via SMS. Thus the Automated Home Security System is self-sufficient and can be relied upon undoubtedly. Also, it is capable of establishing two way communication with its owner so that he/she can keep a watch on his/her home via sensor information or live video streaming. A camera can be installed for continuous monitoring of the system and its surroundings. The system consists of two main parts: hardware and software. Hardware consists of Microcontroller, Sensors, Buzzer and GSM modem while software is implemented by tools using Embedded ‘C’.

  18. Design and implementation of Remote Digital Energy Meter (RDEM) based on GSM technology

    Science.gov (United States)

    Khan, Muhammad Waseem; Wang, Jie; Irfan, Muhammad; Shiraz, M.; Khan, Ali Hassan

    2017-11-01

    Electric power is one of the basic requirement for socio economic and social prosperity of any country, which is mainly employs for domestic, industrial and agricultural sectors. The primary purpose of this research is to design and implement an energy meter which can remotely control and monitor through global system for mobile (GSM) communication technology. For this purpose, a single phase or three phase digital energy meters are used to add on different advanced modules. The energy meter can be activated and display power consumption information at the consumer premises on liquid crystal display and through a short message service (SMS) by using GSM technology. At the power sending end, an energy meter can be remotely control and monitor through GSM technology without any system disturbances. This study will lead to make the system easier, economical, reliable and efficient for the electrical department.

  19. Field Study of all GSM and WiFi Networks in Amman City from Geospatial Perspective

    Science.gov (United States)

    Hawarey, Mosab; Alibrahim, Mustafa; Jetto, Hamza; Salah Mahmoud, Firas

    2016-04-01

    A thorough field study over multiple months has been conducted in the streets of Amman, the capital city of Jordan, in order to collect massive amounts of GSM and WiFi data and analyze them from geospatial perspective. Some interesting realities have been detected; e.g. the North and West of Amman are much better served by GSM operators than the East, South, and Center. Also, the security measures taken to protect WiFi networks in the North and West are much better than those in the East, South, and Center. This has led to the recognition of an interesting pattern that groups the North and West together, while the East, South, and Center constitute another group. Extremely interesting finding was found; the GSM signals are so strong at certain locations that they constitute direct lethal threat to human health; it is scientifically documented that such strengths would lead to certain human cell mutations and cancer. The exact locations and contributors of such hazards will be disclosed in this paper for the first time. Many tabular and graphical presentations of the data will be presented.

  20. Data on the key performance indicators for quality of service of GSM networks in Nigeria.

    Science.gov (United States)

    Popoola, Segun I; Atayero, Aderemi A; Faruk, Nasir; Badejo, Joke A

    2018-02-01

    In this data article, the Key Performance Indicators (KPIs) for Quality of Service (QoS) of Global System for Mobile Communications (GSM) networks in Nigeria are provided and analyzed. The data provided in this paper contain the Call Setup Success Rate (CSSR), Drop Call Rate (DCR), Stand-alone Dedicated Channel (SDCCH) congestion, and Traffic Channel (TCH) congestion for the four GSM network operators in Nigeria (Airtel, Etisalat, Glo, and MTN). These comprehensive data were obtained from the Nigerian Communications Commission (NCC). Significant differences in each of the KPIs for the four quarters of each year were presented based on Analysis of Variance (ANOVA). The values of the KPIs were plotted against the months of the year for better visualization and understanding of data trends across the four quarters. Multiple comparisons of the mean-quarterly differences of the KPIs were also presented using Tukey's Post Hoc test. Public availability and further interpretation and discussion of these useful information will assist the network providers, Nigerian government, local and international regulatory bodies, policy makers, and other stakeholders in ensuring access of people, machines, and things to high quality telecommunications services.

  1. Can LTE become an alternative to GSM-R?

    DEFF Research Database (Denmark)

    Sniady, Aleksander; Soler, José

    GSM-R is the first widely adopted international mobile communication network for railways. It is a part of the European Rail Traffic Management System (ERTMS), which substitutes legacy national railway signaling technologies. GSM-R is designed to provide two fundamental services: transmission of ...

  2. Design and Implementation of GSM Based Transformer Phase ...

    African Journals Online (AJOL)

    In this work, the design and implementation of a transformer phase monitoring system, which continuously check for blown fuses on each phases of the distribution transformer was carried out. The system promptly reports any transformer with blown J&P fuse via a preprogrammed SMS which will state the location of the ...

  3. Design Of A Doherty Power Amplifier For GSM Systems

    OpenAIRE

    Saad Wasmi Osman

    2013-01-01

    This paper presents the design and analysis of Doherty power amplifier. The Doherty amplifier is used in  a base station for mobile system because of its high efficiency. The class AB power amplifier used in the configuration of the main and auxiliary amplifier. The result obtained shows that the Doherty power amplifier can be used on a wide band spectrum, the amplifier works at 900MHz and has very good power added efficiency (PAE) and gain. The amplifier can also work at 1800MHz at input pow...

  4. In-vitro exposure of neuronal networks to the GSM-1800 signal.

    Science.gov (United States)

    Moretti, Daniela; Garenne, André; Haro, Emmanuelle; Poulletier de Gannes, Florence; Lagroye, Isabelle; Lévêque, Philippe; Veyret, Bernard; Lewis, Noëlle

    2013-12-01

    The central nervous system is the most likely target of mobile telephony radiofrequency (RF) field exposure in terms of biological effects. Several electroencephalography (EEG) studies have reported variations in the alpha-band power spectrum during and/or after RF exposure, in resting EEG and during sleep. In this context, the observation of the spontaneous electrical activity of neuronal networks under RF exposure can be an efficient tool to detect the occurrence of low-level RF effects on the nervous system. Our research group has developed a dedicated experimental setup in the GHz range for the simultaneous exposure of neuronal networks and monitoring of electrical activity. A transverse electromagnetic (TEM) cell was used to expose the neuronal networks to GSM-1800 signals at a SAR level of 3.2 W/kg. Recording of the neuronal electrical activity and detection of the extracellular spikes and bursts under exposure were performed using microelectrode arrays (MEAs). This work provides the proof of feasibility and preliminary results of the integrated investigation regarding exposure setup, culture of the neuronal network, recording of the electrical activity, and analysis of the signals obtained under RF exposure. In this pilot study on 16 cultures, there was a 30% reversible decrease in firing rate (FR) and bursting rate (BR) during a 3 min exposure to RF. Additional experiments are needed to further characterize this effect. © 2013 Wiley Periodicals, Inc.

  5. Method of analysis of populations exposure and radio coverage of GSM and UMTS mobile phone networks

    International Nuclear Information System (INIS)

    Gaudaire, Francois; Noe, Nicolas; Dufour, Jean Benoit; De Seze, Rene; Cagnon, Patrice; Selmaoui, Brahim; Mauger, Samuel; Thuroczy, Georges; Mazet, Paul

    2012-01-01

    We present a description and preliminary results of a large-scale project (COMOP) started in 2009 by the Ministry for Ecology, Sustainable Development and Energy and the National Agency of Frequencies (ANFR). This work is collaborative between the government, municipalities, associations, network operators and agencies. This project concerns GSM and UMTS mobile phone networks. Sixteen voluntary pilot communes were selected to carry out the experiments. This work is based on numerical modeling methods associated with various innovative measurement campaigns. It consists of: - determination of current status of exposure to radiofrequency electromagnetic fields emitted by base station antennas by modeling and measurements. - investigations on reducing this exposure while assessing the impact of parallel territorial coverage and quality of service of mobile networks. This study has established a comprehensive scientific realization of human exposure to radio-frequencies from base station antennas. These results constitute an innovative approach and are relevant in terms of dialogue in the current debate about positioning of base stations. (authors)

  6. Design and Implementation of IoT Cloud Moveable SCADA Supported by GSM for Industrial Applications

    Directory of Open Access Journals (Sweden)

    Mahmoud Shaker Nasr

    2017-05-01

    Full Text Available The world at the beginning of a new era of innovation and development with the rise of the industrial Internet or Internet of Things, IoT. It takes the space through the convergence of the global industrial system with the power of advanced computing, analytics, and low cost sensor devices and innovation of communication allowed by the Internet. One of the most important developments is IoT SCADA systems, which are considered as infrastructure of society because of their potential enormous in several industrial applications. This paper presents the design of a new generation of SCADA, named moveable SCADA , based on IoT cloud, and supported by GSM for more flexibility and reliability. The system is applied to industrial application that consists of three-control processes which are temperature, liquid level and motor processes. The three control processes data acquisition and controllers are implemented using embedded microcontroller system while a gateway is used to transfer the data proceed in field supervisor at first as well as main supervisor and monitoring engineer through IoT cloud. The system supported by GSM unit to support the system in case of internet failure. Also a camera is added to the system in order to monitor any location, any location (determined by any of the authorities in the field where the camera is mounted. The proposed SCADA is implemented practically and tested for many cases; the presented obtained results demonstrate that the system operation is very fair and meet the required targets.

  7. INTERFACING VISIBLE LIGHT COMMUNICATION WITH GSM NETWORKS TO PREVENT THE THEFT OF THE VEHICLE

    Directory of Open Access Journals (Sweden)

    P. Prabu

    2015-09-01

    Full Text Available Visible Light Communication (VLC by means of white Light Emitting Diode (LED is an alternate and most promising technology for existing Radio Frequency (RF communication. We proposed one of the important applications of VLC to prevent the theft of the vehicle. Every year approximately 36,000 vehicles worth Rs.115 crores are stolen in India. In critical road condition, only 15,000 are traced and many spare parts of vehicle are found missing. Even the existing technologies have some disadvantages related to the problem stated. In our paper, we dealt with the data communication through LED. One of the optical wireless communication having short range is called as VLC whose visible light spectrum starts from 380 nm and ends at 780 nm and it has an incomparable data rate of 10GB/s whereas the speed is 1MB/s on Bluetooth and for Infra Red (IR the speed is 4MB/s. We try to achieve the communication through VLC between 1 car - car to prevent the accident and 2 car - tollgate and received signal from tollgate is transmitted to Global System for Mobile communication (GSM network using microcontroller to prevent the theft of vehicle. To enhance the security of VLC, Advanced Encryption Standard (AES algorithm is used and the result is illustrated with the help of LabVIEW.

  8. Self-Organizing Networks (SON) Self-Planning, Self-Optimization and Self-Healing for GSM, UMTS and LTE

    CERN Document Server

    Ramiro, Juan

    2011-01-01

    With the current explosion in network traffic, and mounting pressure on operators' business case, Self-Organizing Networks (SON) play a crucial role. They are conceived to minimize human intervention in engineering processes and at the same time improve system performance to maximize Return-on-Investment (ROI) and secure customer loyalty. Written by leading experts in the planning and optimization of Multi-Technology and Multi-Vendor wireless networks, this book describes the architecture of Multi-Technology SON for GSM, UMTS and LTE, along with the enabling technologies for SON planning, opti

  9. Reminder: GSM

    CERN Multimedia

    2003-01-01

    1- Your present GSM subscription (SIM card) will no longer be valid as from the 5th January 2004. 2- Short numbers 16xxxx (where xxxx are your current last 4 digits) will remain valid. 3- Your new number from outside will then be +4176 487xxxx. 4- From the 20th December to the 4th January 2004 (CERN's official holiday) your GSM will be unusable underground. Nota bene: Due to the high costs involved calls from outside will not be automatically diverted to a "combox" indicating that your number has changed. It is therefore up to you to inform your correspondents of your GSM number change. For further information on the GSM Migration see the CERN home page: http://cern.ch/

  10. DESIGN AND PERFORMANCE ANALYSIS OF VCO FOR STANDARD GSM USING MEMS

    Directory of Open Access Journals (Sweden)

    Khalid A. S. Al-Khateeb

    2010-05-01

    Full Text Available The design of a prototype monolithic Micro Electro-Mechanical Systems (MEMS electronic circuits, namely the Voltage Controlled Oscillators (VCOs is presented. The components can achieve the stringent requirements of wireless communication applications such as GSM cellular telephony. The VCO meets the low phase noise specifications of -136 dBc/Hz at large offset frequency of 3MHz, over the appropriate frequency range. The model of the monolithic VCO is based on the topology of the Colpitts Oscillator. It is relatively less complicated, which facilitates the practical integration of the MEMS components into the configuration. The variable capacitor and the monolithic 3-D coil inductor are suitable for low phase-noise and low power consumption at the application frequencies. A PSpice simulation model was developed with MEMS switching devices that can be integrated into the system. The model helps in determining the design parameters, which affect the performance and operation reliability of the RF transceiver system, for which a prototype has been tested and proved successful.

  11. CERN GSM monitoring system

    CERN Multimedia

    Ghabrous Larrea, C

    2009-01-01

    As a result of the tremendous development of GSM services over the last years, the number of related services used by organizations has drastically increased. Therefore, monitoring GSM services is becoming a business critical issue in order to be able to react appropriately in case of incident. In order to provide with GSM coverage all the CERN underground facilities, more than 50 km of leaky feeder cable have been deployed. This infrastructure is also used to propagate VHF radio signals for the CERN’s fire brigade. Even though CERN’s mobile operator monitors the network, it cannot guarantee the availability of GSM services, and for sure not VHF services, where signals are carried by the leaky feeder cable. So, a global monitoring system has become critical to CERN. In addition, monitoring this infrastructure will allow to characterize its behaviour over time, especially with LHC operation. Given that commercial solutions were not yet mature, CERN developed a system based on GSM probes and an application...

  12. Distributed monitoring architecture for movable objects over the GSM system

    Science.gov (United States)

    Chen, Jui-fa; Lin, Wei-Chuan; Chung, Chi-Ming; Tsai, Kun-Hsiao; Chang, C. H.; Hu, Wen-Chen

    2000-12-01

    With the popularity of the network, many applications have been designed to be a distributed system. The more distance for communication, the more hardware and lines for communication are needed. As the GSM has been widely used for telecommunication, it can also be applied to the wireless communication. This paper proposes a wireless monitoring architecture based on the GSM system and takes a car system as a test case. The proposed architecture is divided into three parts. The first is that the data collected from the sensor are sent to the GSM provider by the simulated message of GSM. The second is that the GSM provider processes the received data. To reduce the transmission traffic, a dead-reckoning algorithm is applied to decide whether the process result should be sent to the monitoring center or not. The third is that the monitoring center receives the data which are sending from the GSM provider to give advises to the car driver. With the help of this proposed architecture, a wireless monitoring architecture based on GSM system is verified. In addition, the monitoring center can combine with the GIS to display the car status in an electronic map.

  13. Development of low cost wireless radiation monitoring station using GSM network

    International Nuclear Information System (INIS)

    Nur Aira Abd Rahman; Mohd Ashhar Khalid; Nor Arymaswati Abdullah; Roslan Md Dan

    2006-01-01

    SMS or Short Message Service is a mean of GSM wireless communication that allow text messages to be sent to and from mobile cell phones. While SMS communication is mainly utilized at personal level or person to person basis; the usage of SMS can be extended into nuclear application specifically in radiation monitoring. This paper explains the development of a wireless station assembled by using a recycled Siemens M50 cell phone as substitutes to GSM modem, a PIC micro controller, and MINT-ISG home made digital survey meter at the remote transmitting site. While at the receiving end; an online monitoring system is set-up by using a Bluetooth enabled cell phone, a Bluetooth dongle, and a PC with Labview 8.0 software written as the Data logger which also served as the PC-Bluetooth interface platform. Wireless station at the remote area operates by continuously sending SMS in every 3 minutes to a predefined cellular number located at the monitoring system. The SMS consists of 6 data which individually is a survey meter readings recorded at each 30 seconds duration. At the receiver, Data logger program will retrieve the SMS from the cell phone via Bluetooth and extract the original 6 readings to be displayed on PC. The system has been successfully tested to detect and log radiation data for extended period of time. (Author)

  14. Implementation of a digital cross-connect switch to a GSM network testing environment

    OpenAIRE

    Haverinen, Perttu

    2010-01-01

    Purpose of this thesis was to implement a Nokia Digital Cross-Connect Switch for Time-Division Multiplexing (SXC T) device to a telecommunication testing laboratory. Thesis work was done in local Nokia Siemens Networks corporation site in Tampere, Finland. SXC T acts as a device that interconnects network elements and enables dynamic, software based switching and creation of circuits. Tasks of device are similar to a typical IP network packet switch, but with enhanced features. It provides th...

  15. On the Capacity of a GSM Frequency Hopping network with Intelligent Underlayer-Overlayer

    DEFF Research Database (Denmark)

    Nielsen, Thomas Toftegaard; Wigard, Jeroen; Mogensen, Preben Elgaard

    1997-01-01

    . By combining this reuse partitioning with frequency hopping, an increase in the network capacity in terms of carried traffic per cell is achieved. Simulations have indicated that for slow moving mobiles a gain of approximately 35% is achieved by this new feature when compared with a frequency hopping network...

  16. On a Handover Algorithm in a PCS1900/GSM/DCS1800 Network

    DEFF Research Database (Denmark)

    Wigard, Jeroen; Nielsen, Thomas Toftegaard; Michaelsen, Per Henrik

    1999-01-01

    Traffic reason handover is a functionality that distributes the traffic out over the network according to the traffic load. This can decrease the blocking and thus increase the quality of service (QoS). Its potential gain is analytically calculated and network simulations are performed to evaluate...

  17. External GSM phone calls now made simpler

    CERN Multimedia

    2007-01-01

    On 2 July, the IT/CS Telecom Service introduced a new service making external calls from CERN GSM phones easier. A specific prefix is no longer needed for calls outside CERN. External calls from CERN GSM phones are to be simplified. It is no longer necessary to use a special prefix to call an external number from the CERN GSM network.The Telecom Section of the IT/CS Group is introducing a new system that will make life easier for GSM users. It is no longer necessary to use a special prefix (333) to call an external number from the CERN GSM network. Simply dial the number directly like any other Swiss GSM customer. CERN currently has its own private GSM network with the Swiss mobile operator, Sunrise, covering the whole of Switzerland. This network was initially intended exclusively for calls between CERN numbers (replacing the old beeper system). A special system was later introduced for external calls, allowing them to pass thr...

  18. SMS service from your GSM mobile phone

    CERN Multimedia

    IT Department

    2009-01-01

    The exchange of SMS (Short Message Service) messages is a very popular application of GSM mobile services. However, the use of the application with a CERN subscription is subject to certain conditions: First of all, only text messages can be sent and received with a CERN GSM subscription. These messages are limited to 160 characters. MMS (Multimedia Message Service) messages, which consist in attaching pictures, videos or sounds to a message, are not supported by the current CERN mobile network configuration. In addition, value-added SMS or SMS premium messages (e.g. messages to short numbers involving extra charges) are not permitted. Before sending a message, you must first record the number of the message centre (+41765980000) in your mobile. In principle, this configuration setting is automatically applied to all standard GSM mobile phones when they are issued. To send a message to another GSM user, you must of course enter his or her GSM number. This number must be e...

  19. A Methodology for Measuring Voice Quality Using PESQ and Interactive Voice Response in the GSM Channel Designed by OpenBTS

    Directory of Open Access Journals (Sweden)

    Pavol Partila

    2013-01-01

    Full Text Available This article discusses a methodology for rating the quality of mobile calls. Majority telecommunications service from the perspective of the whole world is using mobile telephony networks. One of the problems affecting this service and its quality are landscape barriers, which prevent the spread signal. Price and complex construction of classic BTS does not allow their dense distribution. In such cases, one solution is to use OpenBTS technology. Design of OpenBTS is more available, so it can be applied to much more places and more complex points. Purpose of this measurement is a model for effective stations deployment, due to shape and distribution of local barriers that reduce signal power, and thus the quality of speech. GSM access point for our mobile terminals is OpenBTS USRP N210 station. The PESQ method for evaluating of speech quality is compared with the subjective evaluation, which provides Asterisk PBX with IVR call back. Measurement method was taken into account the call quality depending on terminal position. The measured results and its processing bring knowledge to use this technology for more complicated locations with degraded signal level and increases the quality of voice services in telecommunications.

  20. Impact of Queuing on Call Completion Rate in GSM Networks | Nkop ...

    African Journals Online (AJOL)

    In this paper, we use the queuing approach to develop a model for call completion, making signal power considerations as well. A General User Interface (GUI) is designed for the developed model using MATLAB and the impact of queuing on call completion is analysed by carrying out an assessment of the performance of ...

  1. Internet Access from CERN GSM subscriptions

    CERN Document Server

    IT Department

    2008-01-01

    The data service on GSM subscriptions has been improved, allowing CERN users to access the Internet directly. A CERN GSM subscription with data option now allows you to connect to the Internet from a mobile phone or a PC equipped with a GSM modem. The previous access (CERN intranet) still exists. To get access to the new service, you will find all the information on configurations at: http://cern.ch/gprs The use of this service on the Sunrise network is charged on a flat-rate basis (no extra charge related to the volume of downloaded data). Depending on your CERN subscription type (standard or master), you can also connect to foreign GSM data networks (roaming), but this is strongly discouraged, except where absolutely necessary, due to international roaming charges. Telecom Section, IT/CS

  2. Performance and limits of KNN-based positioning methods for GSM networks over leaky feeder in underground tunnels

    CERN Document Server

    Pereira, Fernando; Moreira, Adriano; Ricardo, Manuel

    2012-01-01

    Localisation techniques have long been of major importance for safety systems and a lot of research has been conducted in the distributed computing field regarding its functionality and reliability. In the specific scenario of long yet narrow tunnels existing at CERN, localisation methods will enable a number of applications and processes to substantially reduce human intervention. In this article, we evaluate the use of fingerprinting techniques with GSM signal available throughout the LHC tunnel via a radiating cable and compare some methods to estimate the location. In the tests, 16 variants of the K-Nearest Neighbour algorithm, employing different distance weighting methods and fingerprint grouping functions, are taken into consideration and their performance is assessed with a specific rating algorithm. The existing GSM infrastructure and tunnel conditions seem to be favourable to the adoption of these fingerprinting methods. Nevertheless, significant variations in the signal have been observed which mig...

  3. A Review Paper on Design of GPS and GSM Based Intelligent Ambulance Monitoring

    OpenAIRE

    Dr. Shantanu K. Dixit; Miss. Ashwini A. Joshi

    2014-01-01

    Proposed paper presents design of such a monitoring system for emergency patient transportation employing ARM 7 processor module. The system will be useful for monitoring ambulance location using Google map. It also include biomedical sensors to monitor heart bit rate and temperature of patient through SMS. The front end application at the monitoring system is developed using visual basic software in Personal Computers. It can display location of ambulance and status of heart ...

  4. Hierarchical Network Design

    DEFF Research Database (Denmark)

    Thomadsen, Tommy

    2005-01-01

    Communication networks are immensely important today, since both companies and individuals use numerous services that rely on them. This thesis considers the design of hierarchical (communication) networks. Hierarchical networks consist of layers of networks and are well-suited for coping...... with changing and increasing demands. Two-layer networks consist of one backbone network, which interconnects cluster networks. The clusters consist of nodes and links, which connect the nodes. One node in each cluster is a hub node, and the backbone interconnects the hub nodes of each cluster and thus...... the clusters. The design of hierarchical networks involves clustering of nodes, hub selection, and network design, i.e. selection of links and routing of ows. Hierarchical networks have been in use for decades, but integrated design of these networks has only been considered for very special types of networks...

  5. Liner Service Network Design

    DEFF Research Database (Denmark)

    Brouer, Berit Dangaard

    with leased containers. Computational results are reported for seven instances based on real-life shipping networks. Solving the relaxed linear path flow model with a column generation algorithm outperforms solving the relaxed linear arc flow model with the CPLEX barrier solver even for very small instances...... a predefined subset of services, while maintaining a full view of the cargo flows in the network. This could prove a valuable decisions support tool for planners when the network is incrementally adjusted to new market situations and to evaluate the consequence of strategic decisions. The thesis contributes......This thesis concerns design of liner shipping networks using operations research to optimize liner shipping networks at the strategic, tactical and operational level. Liner shipping networks are often compared to public transit networks as they consist of a set of scheduled sailings connecting...

  6. CERN GSM SUBSCRIPTIONS

    CERN Multimedia

    Labo Telecom

    2002-01-01

    AS Division has created a new EDH document for handling all GSM subscription requests and amendments. This procedure will enter force immediately and from now on the Labo Telecom stores will no longer be able to deal with requests submitted on paper forms. Detailed information on the subject can be found here and the Labo Telecom stores will continue to open every day between 11.00 a.m. and 12.00 midday. IT-CS-TEL, Labo Telecom

  7. OPTIMAL NETWORK TOPOLOGY DESIGN

    Science.gov (United States)

    Yuen, J. H.

    1994-01-01

    This program was developed as part of a research study on the topology design and performance analysis for the Space Station Information System (SSIS) network. It uses an efficient algorithm to generate candidate network designs (consisting of subsets of the set of all network components) in increasing order of their total costs, and checks each design to see if it forms an acceptable network. This technique gives the true cost-optimal network, and is particularly useful when the network has many constraints and not too many components. It is intended that this new design technique consider all important performance measures explicitly and take into account the constraints due to various technical feasibilities. In the current program, technical constraints are taken care of by the user properly forming the starting set of candidate components (e.g. nonfeasible links are not included). As subsets are generated, they are tested to see if they form an acceptable network by checking that all requirements are satisfied. Thus the first acceptable subset encountered gives the cost-optimal topology satisfying all given constraints. The user must sort the set of "feasible" link elements in increasing order of their costs. The program prompts the user for the following information for each link: 1) cost, 2) connectivity (number of stations connected by the link), and 3) the stations connected by that link. Unless instructed to stop, the program generates all possible acceptable networks in increasing order of their total costs. The program is written only to generate topologies that are simply connected. Tests on reliability, delay, and other performance measures are discussed in the documentation, but have not been incorporated into the program. This program is written in PASCAL for interactive execution and has been implemented on an IBM PC series computer operating under PC DOS. The disk contains source code only. This program was developed in 1985.

  8. Designing for Networked Communications

    DEFF Research Database (Denmark)

    Designing for Networked Communications: Strategies and Development explains how to plan, use, and understand the products and the dynamic social processes and tasks some of the most vital innovations in the knowledge society depend upon– social as well as technological. Focusing on various forms...... and important research in a variety of forms for networked communications. A constructive and critical view of the interplay between the new electronic and the more conventional modes of communication are utilized, while studies of organizational work practices demonstrate that the use of new technologies...... of design, implementation and integration of computer mediated communication, this book bridges the academic fields of computer science and communication studies. Designing for Networked Communications: Strategies and Development uses an interdisciplinary approach, and presents results from recent...

  9. Designing for Networked Communications

    DEFF Research Database (Denmark)

    Designing for Networked Communications: Strategies and Development explains how to plan, use, and understand the products and the dynamic social processes and tasks some of the most vital innovations in the knowledge society depend upon– social as well as technological. Focusing on various forms...... of design, implementation and integration of computer mediated communication, this book bridges the academic fields of computer science and communication studies. Designing for Networked Communications: Strategies and Development uses an interdisciplinary approach, and presents results from recent...... and important research in a variety of forms for networked communications. A constructive and critical view of the interplay between the new electronic and the more conventional modes of communication are utilized, while studies of organizational work practices demonstrate that the use of new technologies...

  10. Designing Networks for Innovation

    Science.gov (United States)

    Laskowski, Paul Luke

    2009-01-01

    The last decades have seen tremendous growth and transformation in the Internet's commercial landscape. Underneath this success, however, the underlying network architecture has shown a marked resistance to change; it is now described as stagnant and ossified. Numerous design proposals have been developed by researchers, implemented in code, and…

  11. Optimal Network-Topology Design

    Science.gov (United States)

    Li, Victor O. K.; Yuen, Joseph H.; Hou, Ting-Chao; Lam, Yuen Fung

    1987-01-01

    Candidate network designs tested for acceptability and cost. Optimal Network Topology Design computer program developed as part of study on topology design and analysis of performance of Space Station Information System (SSIS) network. Uses efficient algorithm to generate candidate network designs consisting of subsets of set of all network components, in increasing order of total costs and checks each design to see whether it forms acceptable network. Technique gives true cost-optimal network and particularly useful when network has many constraints and not too many components. Program written in PASCAL.

  12. On IPTV network design

    Science.gov (United States)

    Li, Guangzhi; Wang, Dongmei

    2007-11-01

    With more service providers making considerable investments to roll out multimedia services using IP technology, multimedia distribution, especially broadcast TV distribution over an IP network, the so called IPTV, is expected to grow impressively over coming years. However, there are confusing concepts and claims for this new technology: What is IPTV? Why do we need IPTV? How does it work? What are the requirements to design an efficient IPTV network? Are there any research problems? What are the solutions? In this paper, we will try to provide initial answers to all those questions based on our understanding and research work.

  13. Modified TEM cell design exposure system for in vitro exposure of cultured human astrocytes to 900 MHz GSM mobile phone type signals

    International Nuclear Information System (INIS)

    McKenzie, R.J.; McIntosh, R.L.; Iskra, S.; Carratelli, A.

    2002-01-01

    Full text: A key to the rigour of any experiment seeking to investigate possible effects on living systems of the electromagnetic energy (EME) from mobile phones is to ensure that the exposures used are accurately known and reflect the actual exposures. To achieve well controlled and characterised radiofrequency (RF) exposures is not trivial, and has been a concern in many previous studies. At St Vincent's Hospital Centre for Immunology (CFI), an in vitro study is being performed of possible gene expression changes in cultured human astrocytes exposed to GSM mobile phone type signals. In order to provide rigorous RF dosimetry for the study, Telstra Research Laboratories (TRL) has developed a modified transverse electromagnetic (TEM) cell exposure system. This paper will describe salient aspects of the design and development of the system used at CFI. In the experimental design proposed by CFI, live human astrocyte cells are exposed in standard Falcon TM 25 cm 3 plastic culture flasks while incubated in a CO 2 atmosphere at 37 deg C. The cells typically exist as a very thin monolayer (microns) adhered to the bottom of the flask under a layer of several millimetres of nutrient media. This particular arrangement presents a number of challenges for the design of an appropriate RF exposure system. Many RF exposure systems rely on measurements of average absorption within the target material to determine the specific absorption rate (SAR) in the sample. The actual SAR at any given point in the exposed volume may differ markedly from this average value, and typically varies quadratically with height (h) within the sample, where h is taken to be in the direction of the incident electric (E) field. This variance may be tolerable where the cells are distributed in solution throughout the volume, but this is not the case in this instance. Alternatively, keeping the sample very thin can reduce the variance. However, this limits the efficiency of the system, so that high input

  14. Network Analysis, Architecture, and Design

    CERN Document Server

    McCabe, James D

    2007-01-01

    Traditionally, networking has had little or no basis in analysis or architectural development, with designers relying on technologies they are most familiar with or being influenced by vendors or consultants. However, the landscape of networking has changed so that network services have now become one of the most important factors to the success of many third generation networks. It has become an important feature of the designer's job to define the problems that exist in his network, choose and analyze several optimization parameters during the analysis process, and then prioritize and evalua

  15. Optical network design and planning

    CERN Document Server

    Simmons, Jane M

    2014-01-01

    This book takes a pragmatic approach to designing state-of-the-art optical networks for backbone, regional, and metro-core networks.   Algorithms and methodologies related to routing, regeneration, wavelength assignment, subrate-traffic grooming, and protection are presented, with an emphasis on optical-bypass-enabled (or all-optical) networks. There are numerous case studies throughout the text to illustrate the concepts, using realistic networks and traffic sets. A full chapter of economic studies offers guidelines as to when and how optical-bypass technology should be deployed. There is also extensive coverage of recent research to provide insight into how optical networks are likely to evolve. The second edition includes new chapters on dynamic optical networking and flexible/elastic optical networks. There is expanded coverage of new physical-layer technology and its impact on network design, along with enhanced coverage of ROADM architectures, including the colorless, directionless, contentionless, a...

  16. Understanding and designing computer networks

    CERN Document Server

    King, Graham

    1995-01-01

    Understanding and Designing Computer Networks considers the ubiquitous nature of data networks, with particular reference to internetworking and the efficient management of all aspects of networked integrated data systems. In addition it looks at the next phase of networking developments; efficiency and security are covered in the sections dealing with data compression and data encryption; and future examples of network operations, such as network parallelism, are introduced.A comprehensive case study is used throughout the text to apply and illustrate new techniques and concepts as th

  17. RNEDE: Resilient Network Design Environment

    Energy Technology Data Exchange (ETDEWEB)

    Venkat Venkatasubramanian, Tanu Malik, Arun Giridh; Craig Rieger; Keith Daum; Miles McQueen

    2010-08-01

    Modern living is more and more dependent on the intricate web of critical infrastructure systems. The failure or damage of such systems can cause huge disruptions. Traditional design of this web of critical infrastructure systems was based on the principles of functionality and reliability. However, it is increasingly being realized that such design objectives are not sufficient. Threats, disruptions and faults often compromise the network, taking away the benefits of an efficient and reliable design. Thus, traditional network design parameters must be combined with self-healing mechanisms to obtain a resilient design of the network. In this paper, we present RNEDEa resilient network design environment that that not only optimizes the network for performance but tolerates fluctuations in its structure that result from external threats and disruptions. The environment evaluates a set of remedial actions to bring a compromised network to an optimal level of functionality. The environment includes a visualizer that enables the network administrator to be aware of the current state of the network and the suggested remedial actions at all times.

  18. Networking systems design and development

    CERN Document Server

    Chao, Lee

    2009-01-01

    Effectively integrating theory and hands-on practice, Networking Systems Design and Development provides students and IT professionals with the knowledge and skills needed to design, implement, and manage fully functioning network systems using readily available Linux networking tools. Recognizing that most students are beginners in the field of networking, the text provides step-by-step instruction for setting up a virtual lab environment at home. Grounded in real-world applications, this book provides the ideal blend of conceptual instruction and lab work to give students and IT professional

  19. The CERN GSM monitoring system

    International Nuclear Information System (INIS)

    Ghabrous, Carlos

    2010-01-01

    This paper presents the way CERN has approached the problem of monitoring its own GSM infrastructure, especially in the Large Hadron Collider (LHC) accelerator tunnel and other underground facilities, where a leaky feeder cable carries mobile phone signals, and where this technology is the only means for inter-personnel communications.

  20. Approximability of Robust Network Design

    NARCIS (Netherlands)

    Olver, N.K.; Shepherd, F.B.

    2014-01-01

    We consider robust (undirected) network design (RND) problems where the set of feasible demands may be given by an arbitrary convex body. This model, introduced by Ben-Ameur and Kerivin [Ben-Ameur W, Kerivin H (2003) New economical virtual private networks. Comm. ACM 46(6):69-73], generalizes the

  1. PENERAPAN FITUR ADAPTIVE MULTI RATE (AMR PADA JARINGAN GSM

    Directory of Open Access Journals (Sweden)

    Abdusy Syarif

    2010-05-01

    Full Text Available Adaptive Mutlirate (AMR is a feature that plays an important role in the efficiency of use of cell/voice channels and GSM networks in overall and it can improve sound quality dynamically based on actual measurements (real time between Mobile Station (MS and Base Transmitter Station (BTS. Resources used as analytical parameters are SQI (Speech Quality Index, MOS (Mean Opinion Score and the sound quality on the network without and with AMR. Measurements using Test Equipment Mobile System (TEMS while locking devices to the single channel and comparing them between the two types of network. Based on test results it is obtained that with voice channels with AMR can increase the value of SQI approximately 40% for fullrate channels and about 60% for half-rate channels producing a remarkable (excellent level, with research and further measuring it is expected to produce better and more perfect sound quality.Kata kunci: AMR, SQI, GSM networkABSTRAK

  2. Competitive Liner Shipping Network Design

    DEFF Research Database (Denmark)

    Karsten, Christian Vad

    shipping company earnings.The operation of the route net constitute the majority of the total costs, so it is essential to achieve a good capacity utilization in a route plan with travel times that satisfy customer requirements. Most academic articles dealing with the design of container networks neither...... take the container transportation times that can be realized in the network nor the number of transshipments into consideration. This is mainly because the optimization problem is based on other transportation networks where these constraints are not decisive to the quality of the network. Furthermore...... network. The result is prototypes of decision support tools to make incremental changes to a network e.g. by adding/deleting ports from routes or change speed between two ports in order to examine how it changes the total earnings taking into account the network’s competitiveness and quality...

  3. LAST REMINDER: GSM Operator change

    CERN Multimedia

    2003-01-01

    CERN changes its mobile phone operator on 5th January 2004. Your old SIM card and number +41 79 201 XXXX will no longer be valid. Your new number will be +41 76 487 XXXX, but still 16 XXXX inside the CERN area. Your last four digits do not change. To obtain your new SIM card, please fill in the web form at http://it-service-gsm.web.cern.ch/it-service-gsm/ or call tel. 76111 if you do not have access to the web. Dates and places for the distribution of the new SIM cards are: - Meyrin site: Building 504, Restaurant 2, from 26/11 to 5/12; - Prevessin site: Building 866, Restaurant 3, room R-11, from 8/12 to 12/12.

  4. A 3D printed dual GSM band near isotropic on-package antenna

    KAUST Repository

    Zhen, Su

    2017-10-25

    In this paper, we propose an on-package dual band monopole antenna with near-isotropic radiation pattern for GSM mobile applications. The proposed antenna is well matched for both GSM 900 and 1800 bands and provides decent gain for both the bands (1.67 and 3.27 dBi at 900 MHz and 1800 MHz respectively). The antenna is printed with silver ink on a 3D printed polymer based package. The package houses the GSM electronics and the battery. By optimizing the antenna arms width and length, a near-isotropic radiation pattern is achieved. Unlike the published isotropic antennas which are either single band or large in size, the proposed antenna covers both GSM bands with required bandwidth and is only half wavelength long. The design is low cost and highly suitable for various GSM applications such as localization, in additional to conventional communication applications.

  5. Design Tools for Large Networks

    CERN Document Server

    Panikashvili, E; 15th IEEE Real Time Conference 2007

    2007-01-01

    The Atlas TDAQ network consists of four separate networks which together total over 4000 ports at 1Gb/s, 40 ports at 10Gbps, 200 Ethernet switches at the edge of the network, 6 multiblade chassis switches at the core and over 20 km of copper and fiber cabling. The NetDesign suite was developed to provide a comprehensive set of design tools that permits the generation of a navigable circuit design, automates a number of routine tasks and provides the user with a powerful and flexible reporting system. Netdesign is an addon extension to the basic functionality of the Microsoft Visio CAD tool. It features: automatic labeling of cables, media / port connection validation, navigation along a cable, schematic hierarchical, cross-page and vertical navigation, overall verification of network diagram and hyperlinks to other equipment databases. The internal network structure can be exported to a 3rd party database from which a user-friendly meta-language is used to process a large variety of reports on the network des...

  6. Design and security of small wireless network

    OpenAIRE

    Žižka, Ladislav

    2012-01-01

    This thesis deals with design and security of small wireless network. Main goal of the thesis is home network design and choice of optimal solution of wireless security. The thesis has four parts. The first part describes computer networks and network components in theory. Next part deals with network design, choosing of network components and setting of them. It also describes some functionalities of alternative firmware DD-WRT. The third part presents common wireless security and network an...

  7. Route 66: Passively Breaking All GSM Channels

    DEFF Research Database (Denmark)

    Vejre, Philip S.; Bogdanov, Andrey

    2014-01-01

    The A5/2 stream cipher used for encryption in the GSM mobile phone standard has previously been shown to have serious weaknesses. Due to a lack of key separation and flaws in the security protocols, these vulnerabilities can also compromise the stronger GSM ciphers A5/1 and A5/3. Despite GSM's huge...... updating procedure of the GSM protocol. This update is performed automatically even when the phone is not actively used. Interestingly, the attack potentially enables eavesdropping of future calls....

  8. Green corridors and network design

    DEFF Research Database (Denmark)

    Panagakos, George

    2016-01-01

    The purpose of this chapter is to investigate the relation between the Trans-European Transport Network (TEN-T) and the green corridor concept. First, the need is established for a corridor governance structure that enables the close cooperation among the numerous stakeholders from both the public...... and private sectors engaged in all corridor related issues ranging from network design to the provision of integrated logistical solutions. The governance scheme of the recently introduced TEN-T core network corridors seems to fulfil this requirement. Following a brief history of TEN-T development, the 2013...... major overhaul of the EU transportation infrastructure policy is outlined and the basic differences with the past are pinpointed. The provisions of the new TEN-T Guidelines are scrutinized so as to check whether the TEN-T core network corridors exhibit the characteristics of a green corridor...

  9. Design aspects of hydrological networks

    NARCIS (Netherlands)

    Made, J.W. van der; Schilperoort, T.; Schaaf, S. van der; Buishand, T.A.; Brouwer, G.K.; Duyvenbooden, W. van; Becinsky, P.

    1986-01-01

    Network design is a subject which is of essential importance for hydrology. The system of hydrological gauging stations provides the information, necessary for all other hydrological activities. In early times hydrological measurements were carried out already. The most famous example is the Roda

  10. Automated minimax design of networks

    DEFF Research Database (Denmark)

    Madsen, Kaj; Schjær-Jacobsen, Hans; Voldby, J

    1975-01-01

    A new gradient algorithm for the solution of nonlinear minimax problems has been developed. The algorithm is well suited for automated minimax design of networks and it is very simple to use. It compares favorably with recent minimax and leastpth algorithms. General convergence problems related...

  11. Telecommunications network modelling, planning and design

    CERN Document Server

    Evans, Sharon

    2003-01-01

    Telecommunication Network Modelling, Planning and Design addresses sophisticated modelling techniques from the perspective of the communications industry and covers some of the major issues facing telecommunications network engineers and managers today. Topics covered include network planning for transmission systems, modelling of SDH transport network structures and telecommunications network design and performance modelling, as well as network costs and ROI modelling and QoS in 3G networks.

  12. Designing Indonesian Liner Shipping Network

    Directory of Open Access Journals (Sweden)

    Armand Omar Moeis

    2017-06-01

    Full Text Available As the largest archipelago nation in the world, Indonesia’s logistics system has not shown excellence according to the parameters of logistics performance index and based on logistics costs percentages from overall GDP. This is due to the imbalances of trading on the western and eastern regions in Indonesia, which impacts the transportation systems costs to and from the eastern regions. Therefore, it is imperative to improve the competitiveness of Indonesian maritime logistics through maritime logistics network design. This research will focus on three levels of decision making in logistics network design, which include type of ships in the strategic level, shipping routes in the tactical level, and container allocation in the operational level with implementing butterfly routes in Indonesia’s logistics networking problems. Furthermore, this research will analyze the impact of Pendulum Nusantara and Sea Toll routes against the company profits and percentages of containers shipped. This research will also foresee how demand uncertainties and multi-period planning should affect decision making in designing the Indonesian Liner Shipping Network.

  13. Design of Computer Network Security

    OpenAIRE

    Ališauskaitė, Vaida

    2008-01-01

    Magistriniame darbe išanalizuoti įvairios paskirties saugos modeliai. Pagal gautus rezultatus sudarytas apibendrintas informacijos saugos praradimo riziką įvertitnantis kompiuterių tinklų saugos modelis. Sukurta grėsmę keliančius įvykius aptinkanti sistema. The master's work analysis different types of security models. It also proposes a new computer network security reference model, which includes risk management process. A suspicious network events detection system is designed to make ne...

  14. Low Power Clock Network Design

    Directory of Open Access Journals (Sweden)

    Inna Vaisband

    2011-05-01

    Full Text Available Power is a primary concern in modern circuits. Clock distribution networks, in particular, are an essential element of a synchronous digital circuit and a significant power consumer. Clock distribution networks are subject to clock skew due to process, voltage, and temperature (PVT variations and load imbalances. A target skew between sequentially-adjacent registers can be obtained in a balanced low power clock tree using techniques such as buffer and wire sizing. Existing skew mitigation techniques in tree-based clock distribution networks, however, are not efficient in coping with post design variations; whereas the latest non-tree mesh-based solutions reliably handle skew variations, albeit with a significant increase in dissipated power. Alternatively, crosslink-based methods provide low power and variation-efficient skew solutions. Existing crosslink-based methods, however, only address skew at the network topology level and do not target low power consumption. Different methods to manage skew and skew variations within tree and non-tree clock distribution networks are reviewed and compared in this paper. Guidelines for inserting crosslinks within a buffered low power clock tree are provided. Metrics to determine the most power efficient technique for a given circuit are discussed and verified with simulation.

  15. Design aspects of hydrological networks

    OpenAIRE

    Made, J.W. van der; Schilperoort, T.; Schaaf, S. van der; Buishand, T.A.; Brouwer, G.K.; Duyvenbooden, W. van; Becinsky, P.

    1986-01-01

    Network design is a subject which is of essential importance for hydrology. The system of hydrological gauging stations provides the information, necessary for all other hydrological activities. In early times hydrological measurements were carried out already. The most famous example is the Roda Gauge at the river Nile in Egypt, from which observations are known since 641 (Hurst et a1.,1965). In the 17th century water stage measurements were carried out in Amsterdam for the ocean going vesse...

  16. Evaluation of ETCS performance with LTE as alternative railway communication network using OPNET

    DEFF Research Database (Denmark)

    Sniady, Aleksander; Soler, José

    2013-01-01

    GSM-Railways (GSM-R) is a communication mobile network designed to fulfill specific communication needs of railways. GSM-R is being widely deployed across Europe and other countries around the world for providing railway voice and train control services (ETCS). Despite that, GSM-R already shows...... various shortcomings in terms of capacity and support for additional data services. This triggers the issue whether railways could greatly benefit from an alternative communication technology. One of the possible alternatives is LTE. In our work we analyze delivery of railway services over an LTE network....... This work is done using OPNET as simulator for modeling real life railway scenarios and communication infrastructure. These scenarios take advantage of OPNET features allowing modeling an end-to-end LTE network, as well as trains movement over an exemplary real life railway line....

  17. Vulnerabilities in GSM technology and feasibility of selected attacks

    Science.gov (United States)

    Voznak, M.; Prokes, M.; Sevcik, L.; Frnda, J.; Toral-Cruz, Homer; Jakovlev, Sergej; Fazio, Peppino; Mehic, M.; Mikulec, M.

    2015-05-01

    Global System for Mobile communication (GSM) is the most widespread technology for mobile communications in the world and serving over 7 billion users. Since first publication of system documentation there has been notified a potential safety problem's occurrence. Selected types of attacks, based on the analysis of the technical feasibility and the degree of risk of these weaknesses, were implemented and demonstrated in laboratory of the VSB-Technical University of Ostrava, Czech Republic. These vulnerabilities were analyzed and afterwards possible attacks were described. These attacks were implemented using open-source tools, software programmable radio USRP (Universal Software RadioPeripheral) and DVB-T (Digital Video Broadcasting - Terrestrial) receiver. GSM security architecture is being scrutinized since first public releases of its specification mainly pointing out weaknesses in authentication and ciphering mechanisms. This contribution also summarizes practically proofed and used scenarios that are performed using opensource software tools and variety of scripts mostly written in Python. Main goal of this paper is in analyzing security issues in GSM network and practical demonstration of selected attacks.

  18. Future alternatives to GSM-R

    DEFF Research Database (Denmark)

    Sniady, Aleksander; Soler, José; Dittmann, Lars

    Signalling is as fundamental contributor to a robust railway system. European Railway Traffic Management System (ERTMS) enhances dynamic train control, interoperability and track utilization. GSM-R is a communication subsystem in ERTMS.......Signalling is as fundamental contributor to a robust railway system. European Railway Traffic Management System (ERTMS) enhances dynamic train control, interoperability and track utilization. GSM-R is a communication subsystem in ERTMS....

  19. Speech Quality Measurement of GSM Infrastructure Built on USRP N210 and OpenBTS Project

    Directory of Open Access Journals (Sweden)

    Marcel Fajkus

    2014-01-01

    Full Text Available The paper deals with the methodology for speech quality measuring in GSM networks using Perceptual Evaluation of Speech Quality (PESQ. The paper brings results of practical measurement of own GSM network build on the Universal Software Radio Peripheral (USRP N210 hardware and OpenBTS software. This OpenBTS station was installed in open terrain, and the speech quality was measured from different distances from the transmitter. The limit parameters of OpenBTS station with USRP N210 were obtained.

  20. Reverse Logistics Network Structures and Design

    NARCIS (Netherlands)

    M. Fleischmann (Moritz)

    2001-01-01

    textabstractLogistics network design is commonly recognized as a strategic supply chain issue of prime importance. The location of production facilities, storage concepts, and transportation strategies are major determinants of supply chain performance. This chapter considers logistics network

  1. Collaborative Trust Networks in Engineering Design Adaptation

    DEFF Research Database (Denmark)

    Atkinson, Simon Reay; Maier, Anja; Caldwell, Nicholas

    2011-01-01

    Within organisations, decision makers have to rely on collaboration with other actors from different disciplines working within highly dynamic and distributed associated networks of varying size and scales. This paper develops control and influence networks within Design Structure Matrices (DSM...

  2. Real-Time Vehicle Data Logging System Using GPS And GSM

    Directory of Open Access Journals (Sweden)

    Win Minn Thet

    2015-07-01

    Full Text Available Abstract This paper proposes and implements a low cost Vehicle Data Logging System using GPS and GSM. This system allows a user to trace the present and past positions recorded in SD card. This system also reads the current position of the vehicle using GPS the data is sent via GSM service from the GSM network. The vehicles position including the driving speed the UTC time and data are stored in the SD card for live and past tracking. All of that GPS data is sent to PIC 18F4520 by the Universal Asynchronous ReceiverTransmitter UART and also store in SD card. GSM also uses UART to transmit. To know the position of the vehicle the owner sends a request through a SMS. The SMS sends to the authorized person through the GSM network. The travel history of the vehicle are stored in a file on an SD card in FAT format.This system is very useful for car tracking for adolescent driver being checked by parent speed limit exceeding leaving a specific area. V The developed system is easy to use requires no additional hardware and permits the selection of the amount of data and the time intervals between the data recordings. In addition the collected data can easily be transferred to a computer via a connected serial port.

  3. GSM module for wireless radiation monitoring system via SMS

    Science.gov (United States)

    Rahman, Nur Aira Abd; Hisyam Ibrahim, Noor; Lombigit, Lojius; Azman, Azraf; Jaafar, Zainudin; Arymaswati Abdullah, Nor; Hadzir Patai Mohamad, Glam

    2018-01-01

    A customised Global System for Mobile communication (GSM) module is designed for wireless radiation monitoring through Short Messaging Service (SMS). This module is able to receive serial data from radiation monitoring devices such as survey meter or area monitor and transmit the data as text SMS to a host server. It provides two-way communication for data transmission, status query, and configuration setup. The module hardware consists of GSM module, voltage level shifter, SIM circuit and Atmega328P microcontroller. Microcontroller provides control for sending, receiving and AT command processing to GSM module. The firmware is responsible to handle task related to communication between device and host server. It process all incoming SMS, extract, and store new configuration from Host, transmits alert/notification SMS when the radiation data reach/exceed threshold value, and transmits SMS data at every fixed interval according to configuration. Integration of this module with radiation survey/monitoring device will create mobile and wireless radiation monitoring system with prompt emergency alert at high-level radiation.

  4. Designing synthetic networks in silico

    NARCIS (Netherlands)

    Smith, Robert W.; Sluijs, van Bob; Fleck, Christian

    2017-01-01

    Background: Evolution has led to the development of biological networks that are shaped by environmental signals. Elucidating, understanding and then reconstructing important network motifs is one of the principal aims of Systems & Synthetic Biology. Consequently, previous research has focused

  5. Computational network design from functional specifications

    KAUST Repository

    Peng, Chi Han

    2016-07-11

    Connectivity and layout of underlying networks largely determine agent behavior and usage in many environments. For example, transportation networks determine the flow of traffic in a neighborhood, whereas building floorplans determine the flow of people in a workspace. Designing such networks from scratch is challenging as even local network changes can have large global effects. We investigate how to computationally create networks starting from only high-level functional specifications. Such specifications can be in the form of network density, travel time versus network length, traffic type, destination location, etc. We propose an integer programming-based approach that guarantees that the resultant networks are valid by fulfilling all the specified hard constraints and that they score favorably in terms of the objective function. We evaluate our algorithm in two different design settings, street layout and floorplans to demonstrate that diverse networks can emerge purely from high-level functional specifications.

  6. Using Network Science to Support Design Research

    DEFF Research Database (Denmark)

    Parraguez Ruiz, Pedro; Maier, Anja

    2016-01-01

    and societal impact. This chapter contributes to the use of network science in empirical studies of design organisations. It focuses on introducing a network-based perspective on the design process and in particular on making use of network science to support design research and practice. The main contribution......A network-based perspective on designing permits research on the complexity of product, process, and people interactions. Strengthened by the latest advances in information technologies and accessibility of data, a network-based perspective and use of appropriate network analysis metrics, theories......, and tools allow us to explore new data-driven research approaches in design. These approaches allow us to move from counting to connecting, meaning to explicitly link disconnected pieces of data, information, and knowledge, and thus to answer far-reaching research questions with strong industrial...

  7. Transmission design in a multimode HFC network

    Science.gov (United States)

    Cambron, G. Keith

    1996-11-01

    Contemporary hybrid fiber coaxial (HFC) networks are capable of supporting a wide range of services including traditional analog video, telephony, digital video, and data services. Each service has unique performance or service requirements. This contribution examines transmission design for one such network. Pacific Bell's advanced communications network (ACN). The design methodology begins with a set of end to end service quality objectives. Network impairments, such as noise, distortion and delay, are allocated across the network elements using a set of standard network models. These models are a representative set of the actual field designs and bound the network operating parameters. Network components, headend equipment, and customer premises equipment are specified analytically or characterized empirically in relationship to the chosen impairment set. The component parameters are then included in analytical models to estimate overall network performance. In addition to the forward path transmission considerations examined by traditional coaxial network designers, other dimensions including power consumption, traffic demand, and message latency are taken into account. Analytical models are used to estimate the effects of multiple modulation schemes within the unified network. The variability introduced by on demand services such as telephony and interactive digital services changes the base computational domain from deterministic models to stochastic ones. These models are then used to set operating parameters at measurable points throughout the network for proof of performance prior to turn up, and for ongoing performance monitoring. For closure, empirical results are compared with model projections as a way of verifying and improving the predictive models.

  8. Smart Business Networks Design and Business Genetics

    NARCIS (Netherlands)

    L-F. Pau (Louis-François)

    2006-01-01

    textabstractWith the emergence of smart business networks, agile networks, etc. as important research areas in management, for all the attractiveness of these concepts, a major issue remains around their design and the selection rules. While smart business networks should provide advantages due to

  9. Information Flows in Networked Engineering Design Projects

    DEFF Research Database (Denmark)

    Parraguez, Pedro; Maier, Anja

    Complex engineering design projects need to manage simultaneously multiple information flows across design activities associated with different areas of the design process. Previous research on this area has mostly focused on either analysing the “required information flows” through activity...... networks at the project level or in studying the social networks that deliver the “actual information flow”. In this paper we propose and empirically test a model and method that integrates both social and activity networks into one compact representation, allowing to compare actual and required...... information flows between design spaces, and to assess the influence that these misalignments could have on the performance of engineering design projects....

  10. Network Design Models for Container Shipping

    DEFF Research Database (Denmark)

    Reinhardt, Line Blander; Kallehauge, Brian; Nielsen, Anders Nørrelund

    This paper presents a study of the network design problem in container shipping. The paper combines the network design and fleet assignment problem into a mixed integer linear programming model minimizing the overall cost. The major contributions of this paper is that the time of a vessel route...

  11. On the application of Dijkstra\\'s algorithms in solving the GSM ...

    African Journals Online (AJOL)

    On the application of Dijkstra\\'s algorithms in solving the GSM Network problem. A W Gbolagade, R K Odunaike, Z O Ogunwobi. Abstract. Journal of the Nigerian Association of Mathematical Physics Vol. 8 2004: pp. 319-322. Full Text: EMAIL FULL TEXT EMAIL FULL TEXT · DOWNLOAD FULL TEXT DOWNLOAD FULL ...

  12. Review of studies validating the protective efficacy of a new technology designed to compensate adverse biological effects caused by vdu and GSM cell phone radiation

    International Nuclear Information System (INIS)

    Youbicier-Simo, B.J.; Messagier, R.; Fillion-Robin, M

    2001-01-01

    A total of 13 studies were initiated and coordinated by Technolab Research Center in 6 laboratories from 3 countries (France, UK, Japan). These studies were aimed at: 1) investigating potential adverse biological effects associated with exposure to non ionizing radiation emitted by two types of communication devices, video display units and cell phones; 2) assessing the efficacy of a compensation magnetic oscillating technology designed to protect from non ionizing radiation. Five types of biological systems including chicken embryos, young chickens, healthy mice, mice suffering from cancer and humans were used. A set of 10 biological parameters were assessed, including embryonic mortality, hormones, antibodies, haematological parameters, stress, mood, ocular damage, neurogenesis, micronuclei formation and intracellular calcium. Overall endpoints were affected by irradiation, in terms of increased embryonic mortality, immune depression, depletion of hormones crucial for the regulation of the immune system, changes in haematological parameters, increased stress, mood alteration, induction of ophthalmologic disorders, inhibition of the neurogenesis in brain areas associated with memory processes, induction of symptoms of cell dysfunction, apoptosis or cancer, and disruption of trans-membrane fluxes of calcium. On the other hand, the compensation magnetic oscillation technology tested allowed significant correction of altered physiological parameters, as well as improvement or disappearance of observed pathological symptoms (author)

  13. Fiber optic Ethernet transceiver for Joint STARS block I GSM

    Science.gov (United States)

    Gatens, Dennis R.; Usberghi, Michael J.

    The authors discuss the use of FiberCom's DPT dual redundant counter-rotating ring Ethernet transceiver, and its use as an integral part of the Joint STARS (Surveillance Target Attack Radar System) surface-to-air battlefield information station called the ground station module (GSM). The Ethernet transceiver uses a dual counter-rotating fiber ring architecture. The operation of the unit enables the network to have fault-tolerant capability with no single point of failure. This results from the unit's ability to reconfigure around a network failure, creating a new working segment from the remaining portion. The medium attachment unit interface conforms to ANSI/IEEE Std. 802.3-1985, the IEEE Standard for Local Area Networks-Carrier Sense Multiple Access with Collision Detection (CSMA/CD) Access Method and Physical Layer Specifications.

  14. Intelligent FDSS Overlay on GSM System (Uplink Analysis

    Directory of Open Access Journals (Sweden)

    L. D. Haro-Ariet

    2005-04-01

    Full Text Available The overlay of an intelligent frequency diversity spread spectrum system (FDSS on the (GSM system is studied. The uplink capacity of both systems is given using a model of 36 hexagonal macrocells. Performance of GSM and FDSS users is investigated. An original GSM system with 48 users/macrocell can be substituted by a mixed system, which has GSM system capacity of 48 users/macrocell and FDSS system capacity of 128 users/macrocell.

  15. Modelling and designing electric energy networks

    International Nuclear Information System (INIS)

    Retiere, N.

    2003-11-01

    The author gives an overview of his research works in the field of electric network modelling. After a brief overview of technological evolutions from the telegraph to the all-electric fly-by-wire aircraft, he reports and describes various works dealing with a simplified modelling of electric systems and with fractal simulation. Then, he outlines the challenges for the design of electric networks, proposes a design process, gives an overview of various design models, methods and tools, and reports an application in the design of electric networks for future jumbo jets

  16. The GSM, Internet, Library and Information Service in Nigerian ...

    African Journals Online (AJOL)

    The GSM, Internet, Library and Information Service in Nigerian Public Libraries. Blessing C Onu. Abstract. This is a discourse on the adaptation and use of the GSM via the Internet in the provision of both on-- and off-line library and information service to subscribers. It gives a brief history of the GSM and how it came to be ...

  17. receive signal strength prediction in the gsm band using wavelet ...

    African Journals Online (AJOL)

    In this work, GSM receive signal strength was monitored in an indoor environment. Samples of GSM receive signal strength was measured on a Mobile Equipment (ME). One-dimensional multilevel wavelet decomposition technique was used to predict the fading phenomenon of the GSM receive signal strength measured.

  18. Design principles in biological networks

    Science.gov (United States)

    Goyal, Sidhartha

    Much of biology emerges from networks of interactions. Even in a single bacterium such as Escherichia coli, there are hundreds of coexisting gene and protein networks. Although biological networks are the outcome of evolution, various physical and biological constraints limit their functional capacity. The focus of this thesis is to understand how functional constraints such as optimal growth in mircoorganisms and information flow in signaling pathways shape the metabolic network of bacterium E. coli and the quorum sensing network of marine bacterium Vibrio harveyi, respectively. Metabolic networks convert basic elemental sources into complex building-blocks eventually leading to cell's growth. Therefore, typically, metabolic pathways are often coupled both by the use of a common substrate and by stoichiometric utilization of their products for cell growth. We showed that such a coupled network with product-feedback inhibition may exhibit limit-cycle oscillations which arise via a Hopf bifurcation. Furthermore, we analyzed several representative metabolic modules and find that, in all cases, simple product-feedback inhibition allows nearly optimal growth, in agreement with the predicted growth-rate by the flux-balance analysis (FBA). Bacteria have fascinating and diverse social lives. They display coordinated group behaviors regulated by quorum sensing (QS) systems. The QS circuit of V. harveyi integrates and funnels different ecological information through a common phosphorelay cascade to a set of small regulatory RNAs (sRNAs) that enables collective behavior. We analyzed the signaling properties and information flow in the QS circuit, which provides a model for information flow in signaling networks more generally. A comparative study of post-transcriptional and conventional transcriptional regulation suggest a niche for sRNAs in allowing cells to transition quickly yet reliably between distinct states. Furthermore, we develop a new framework for analyzing signal

  19. Photonic network-on-chip design

    CERN Document Server

    Bergman, Keren; Biberman, Aleksandr; Chan, Johnnie; Hendry, Gilbert

    2013-01-01

    This book provides a comprehensive synthesis of the theory and practice of photonic devices for networks-on-chip. It outlines the issues in designing photonic network-on-chip architectures for future many-core high performance chip multiprocessors. The discussion is built from the bottom up: starting with the design and implementation of key photonic devices and building blocks, reviewing networking and network-on-chip theory and existing research, and finishing with describing various architectures, their characteristics, and the impact they will have on a computing system. After acquainting

  20. Network Design with Node Degree Balance Constraints

    DEFF Research Database (Denmark)

    Pedersen, Michael Berliner; Crainic, Teodor Gabriel

    This presentation discusses an extension to the network design model where there in addition to the flow conservation constraints also are constraints that require design conservation. This means that the number of arcs entering and leaving a node must be the same. As will be shown the model has...... applications within the design of transportation networks. The model is solved using a Tabu Search heuristic using a hybrid of the add/drop procedure and cycle-based neighbourhoods....

  1. Network design management and technical perspectives

    CERN Document Server

    Piliouras, Teresa C

    2004-01-01

    MAKING THE BUSINESS CASE FOR THE NETWORKManagement Overview of Network DesignDefine the Business ObjectivesDetermine Potential Risks, Dependencies, Costs andBenefitsIdentify Project RequirementsDevelop Project Implementation ApproachStrategic Positioning Using NetworksCase StudiesCalculation of Technology's Strategic ValueDealing with Major Design ChallengesOrganizational Concerns and RecommendationsTechnology Concerns and RecommendationsSimilarities and Differences between Voice and DataNetwork Design and PlanningMajor Trends and Technology EnablersSocietal TrendsService Provider TrendsMajor

  2. Design of the HYREX raingauge network

    Directory of Open Access Journals (Sweden)

    R. J. Moore

    2000-01-01

    Full Text Available Dense raingauge experiments in the past have experienced difficulties in the automated recording of rainfall amount and timing which with the benefit of modern instrument technology are now less problematic. The HYdrological Radar EXperiment, HYREX, provided a timely opportunity to design and implement a dense raingauge network in support of rainfall measurement and modelling research studies concerned with the use of weather radar in hydrology. The principles and random function theory underlying the design of this raingauge network over the Brue catchment in south-west England are detailed in this paper. Keywords: raingauge, design, network, rainfall, flood, spatial correlation

  3. Competitive Liner Shipping Network Design

    DEFF Research Database (Denmark)

    Karsten, Christian Vad; Brouer, Berit Dangaard; Pisinger, David

    2017-01-01

    leg are used to balance sailing speed against operational costs, hence ensuring that the found network is competitive on both transit time and cost. We present a matheuristic for the problem where a MIP is used to select which ports should be inserted or removed on a route. Computational results...... on fluctuations in bunker price which confirms the applicability of the algorithm....

  4. Competitive Liner Shipping Network Design

    DEFF Research Database (Denmark)

    Karsten, Christian Vad; Brouer, Berit Dangaard; Pisinger, David

    leg are used to balance sailings speed against operational costs, hence ensuring that the found network is competitive on both transit time and cost. We present a matheuristic for the problem where a MIP is used to select which ports should be inserted or removed on a route. Computational results...... on fluctuations in bunker price which confirms the applicability of the algorithm....

  5. Designing Broadband Access Networks with Triple Redundancy

    DEFF Research Database (Denmark)

    Pedersen, Jens Myrup; Riaz, Muhammad Tahir; Knudsen, Thomas Phillip

    2005-01-01

    An architecture is proposed for designing broadband access networks, which offer triple redundancy to the end users, resulting in networks providing connectivity even in case of any two independent node or line failures. Two physically independent connections are offered by fiber, and the last...

  6. Designing and Evaluating Sustainable Logistics Networks

    NARCIS (Netherlands)

    J. Quariguasi Frota Neto (João); J.M. Bloemhof-Ruwaard (Jacqueline); J.A.E.E. van Nunen (Jo); H.W.G.M. van Heck (Eric)

    2006-01-01

    textabstractThe objective in this paper is to shed light into the design of logistic networks balancing profit and the environment. More specifically we intend to i) determine the main factors influencing environmental performance and costs in logistic networks ii) present a comprehensive framework

  7. Network architecture functional description and design

    Energy Technology Data Exchange (ETDEWEB)

    Stans, L.; Bencoe, M.; Brown, D.; Kelly, S.; Pierson, L.; Schaldach, C.

    1989-05-25

    This report provides a top level functional description and design for the development and implementation of the central network to support the next generation of SNL, Albuquerque supercomputer in a UNIX{reg sign} environment. It describes the network functions and provides an architecture and topology.

  8. Collaborative Trust Networks in Engineering Design Adaptation

    DEFF Research Database (Denmark)

    Atkinson, Simon Reay; Maier, Anja; Caldwell, Nicholas

    2011-01-01

    Within organisations, decision makers have to rely on collaboration with other actors from different disciplines working within highly dynamic and distributed associated networks of varying size and scales. This paper develops control and influence networks within Design Structure Matrices (DSM...... hinder effective communication and collaboration. Different combinations of trust may therefore improve or impair the likelihood of information flow, transfer and subsequent action (cause and effect). This paper investigates how analysing different types of network-structures-in-being can support...... collaboration and decision-making by using the change prediction method as a way of scoping information propagation between actors within a network....

  9. Heat exchanger networks design with constraints

    International Nuclear Information System (INIS)

    Amidpur, M.; Zoghi, A.; Nasiri, N.

    2000-01-01

    So far there have been two approaches to the problem of heat recovery system design where stream matching constraints exist. The first approach involves mathematical techniques for solving the combinational problem taking due recognition of the constraints. These methodologies are now efficient, still suffer from the problem of taking a significant amount of control and direction away from the designer. The second approach based upon so called pinch technology and involves the use of adaptation of standard problem table algorithm. Unfortunately, the proposed methodologies are not very easy to understand, therefore they fail to provide the insight and generally associated with these approaches. Here, a new pinch based methodology is presented. In this method, we modified the traditional numerical targeting procedure-problem table algorithm which is stream cascade table. Unconstrained groups are established by using of artificial intelligence method such that they have minimum utility consumption among different alternatives. Each group is an individual network, therefore, traditional optimization, used in pinch technology, should be employed. By transferring energy between groups heat recovery can be maximized, then each group designs individually and finally networks combine together. One of the advantages of using this method is simple targeting and easy networks-design. Besides the approach has the potential using of new network design methods such as dual temperature approach, flexible pinch design, pseudo pinch design. It is hoped that this methodology provides insight easy network design

  10. Design of Robust Neural Network Classifiers

    DEFF Research Database (Denmark)

    Larsen, Jan; Andersen, Lars Nonboe; Hintz-Madsen, Mads

    1998-01-01

    This paper addresses a new framework for designing robust neural network classifiers. The network is optimized using the maximum a posteriori technique, i.e., the cost function is the sum of the log-likelihood and a regularization term (prior). In order to perform robust classification, we present...... a modified likelihood function which incorporates the potential risk of outliers in the data. This leads to the introduction of a new parameter, the outlier probability. Designing the neural classifier involves optimization of network weights as well as outlier probability and regularization parameters. We...

  11. A GSM-Based Remote Temperature and Humidity Monitoring System for Granary

    Directory of Open Access Journals (Sweden)

    Zheng Xiao Xi

    2016-01-01

    Full Text Available A remote temperature and humidity monitoring system is designed based on the GSM technology and MSP430. With the digital sensor DSB1820 and SHT11, the temperature and humidity of the granary are detected, and these parameters can be adjusted with the controlling system to adapt various working conditions. Through the GSM system, the detected data could be sent to various monitoring devices, such as cellphones and laptops. These data can be used for data display, inquiry, controlling and storage at the remote terminals. The experimental results show that the system is convenient and concise, which meets the remote monitoring demand for the modern granary.

  12. Designing value-creating supply chain networks

    CERN Document Server

    Martel, Alain

    2016-01-01

    Focusing on the design of robust value-creating supply chain networks (SCN) and key strategic issues related to the number; location, capacity and mission of supply chain facilities (plants, distribution centers) – as well as the network structure required to provide flexibility and resilience in an uncertain world – this book presents an innovative methodology for SCN reengineering that can be used to significantly improve the bottom line of supply chain dependent businesses. Providing readers with the tools needed to analyze and model value creation activities, Designing Value-Creating Supply Chain Networks examines the risks faced by modern supply chains, and shows how to develop plausible future scenarios to evaluate potential SCN designs. The design methods proposed are based on a visual representation formalism that facilitates the analysis and modeling of SCN design problems, book chapters incorporate several example problems and exercises which can be solved with Excel tools (Analysis tools and So...

  13. Ethical Issues in Network System Design

    Directory of Open Access Journals (Sweden)

    Duncan Langford

    1997-05-01

    Full Text Available Today, most desktop computers and PCs are networked that is, they have the ability to link to other machines, usually to access data and other information held remotely. Such machines may sometimes be connected directly to each other, as part of an office or company computer system. More frequently, however, connected machines are at a considerable distance from each other, typically connected through links to global systems such as the Internet, or World Wide Web (WWW. The networked machine itself may be anything from a powerful company computer with direct Internet connections, to a small hobbyist machine, accessing a bulletin board through telephone and modem. It is important to remember that, whatever the type or the location of networked machines, their access to the network, and the network itself, was planned and constructed following deliberate design considerations. In this paper I discuss some ways in which the technical design of computer systems might appropriately be influenced by ethical issues, and examine pressures on computer scientists and others to technically control network related actions perceived as 'unethical'. After examination of the current situation, I draw together the issues, and conclude by suggesting some ethically based recommendations for the future design of networked systems.

  14. Designing for Privacy in Ubiquitous Social Networking

    DEFF Research Database (Denmark)

    Sapuppo, Antonio; Figueiras, Joao

    2015-01-01

    are subject to crucial privacy threats. Inspired by the usability and privacy limitations of existing design solutions, we identify, describe and qualitatively evaluate four drawbacks to be avoided when designing ubiquitous social networking applications. By addressing these drawbacks, services become more...... functional and more oriented to ensure the end users' privacy, thus contributing to the long–term success of this technology....

  15. GSM BASED IRRIGATION CONTROL AND MONITORING SYSTEM

    OpenAIRE

    GODFREY A. MILLS; STEPHEN K. ARMOO; AGYEMAN K. ROCKSON; ROBERT A. SOWAH; MOSES A. ACQUAH

    2013-01-01

    Irrigated agriculture is one of the primary water consumers in most parts of the world. With developments in technology, efforts are being channeled into automation of irrigation systems to facilitate remote control of the irrigation system and optimize crop production and cost effectiveness. This paper describes an on-going work on GSM based irrigation monitoring and control systems. The objective of the work is to provide an approach that helps farmers to easily access, manage and regulate ...

  16. Deriving consistent GSM schemas from DCR graphs

    DEFF Research Database (Denmark)

    Eshuis, Rik; Debois, Søren; Slaats, Tijs

    2016-01-01

    Case Management (CM) is a BPM technology for supporting flexible services orchestration. CM approaches like CMMN, an OMG standard, and GSM, one of CMMN’s core influences, use Event- Condition-Action rules, which can be inconsistent due to cyclic interdependencies between the rules; repairing such...... by a running example of a mortgage loan application; and a prototype implementation available at http://dcr.itu.dk/icsoc16....

  17. Spacecraft designs for VSAT networks

    Science.gov (United States)

    Stern, Alan L.; Wright, David L.

    1990-01-01

    Results are presented from a study to determine the commercial applications of the technology developed for ACTS. Two systems are discussed: point-to-point transmission of T1 (1.544 Mb/s) data channels using Very Small Aperature Terminals, and point-to-point transmission of single channel per carrier data from extremely small ground terminals. Satellite communications systems designed for each of these applications are described.

  18. On cost-effective communication network designing

    Science.gov (United States)

    Zhang, Guo-Qiang

    2010-02-01

    How to efficiently design a communication network is a paramount task for network designing and engineering. It is, however, not a single objective optimization process as perceived by most previous researches, i.e., to maximize its transmission capacity, but a multi-objective optimization process, with lowering its cost to be another important objective. These two objectives are often contradictive in that optimizing one objective may deteriorate the other. After a deep investigation of the impact that network topology, node capability scheme and routing algorithm as well as their interplays have on the two objectives, this letter presents a systematic approach to achieve a cost-effective design by carefully choosing the three designing aspects. Only when routing algorithm and node capability scheme are elegantly chosen can BA-like scale-free networks have the potential of achieving good tradeoff between the two objectives. Random networks, on the other hand, have the built-in character for a cost-effective design, especially when other aspects cannot be determined beforehand.

  19. Design Guidelines for New Generation Network Architecture

    Science.gov (United States)

    Harai, Hiroaki; Fujikawa, Kenji; Kafle, Ved P.; Miyazawa, Takaya; Murata, Masayuki; Ohnishi, Masaaki; Ohta, Masataka; Umezawa, Takeshi

    Limitations are found in the recent Internet because a lot of functions and protocols are patched to the original suite of layered protocols without considering global optimization. This reveals that end-to-end argument in the original Internet was neither sufficient for the current societal network and nor for a sustainable network of the future. In this position paper, we present design guidelines for a future network, which we call the New Generation Network, which provides the inclusion of diverse human requirements, reliable connection between the real-world and virtual network space, and promotion of social potentiality for human emergence. The guidelines consist of the crystal synthesis, the reality connection, and the sustainable & evolutional guidelines.

  20. Design of all Optical Packet Switching Networks

    Directory of Open Access Journals (Sweden)

    Hussein T. Mouftah

    2002-06-01

    Full Text Available Optical switches and wavelength converters are recognized as two of the most important DWDM system components in future all-optical networks. Optical switches perform the key functions of flexible routing, reconfigurable optical cross-connect (OXC, network protection and restoration, etc. in optical networks. Wavelength Converters are used to shift one incoming wavelength to another outgoing wavelength when this needs to be done.  Always residing in optical switches, they can effectively alleviate the blocking probability and help solve contention happening at the output port of switches. The deployment of wavelength converters within optical switches provides robust routing, switching and network management in optical layer, which is critical to the emerging all-optical Internet. However, the high cost of wavelength converters at current stage of manufacturing technology has to be taken into consideration when we design node architectures for an optical network. Our research explores the efficiency of wavelength converters in a long-haul optical network at different degrees of traffic load by running a simulation. Then, we propose a new cost-effective way to optimally design wavelength-convertible switch so as to achieve higher network performance while still keeping the total network cost down. Meanwhile, the routing and wavelength assignment (RWA algorithm used in the research is designed to be a generic one for both large-scale and small-scale traffic. Removing the constraint on the traffic load makes the RWA more adaptive and robust. When this new RWA works in conjunction with a newly introduced concept of wavelength-convertible switches, we shall explore the impact of large-scale traffic on the role of wavelength converter so as to determine the method towards optimal use of wavelength convertible switches for all-optical networks.

  1. Network design for cylinder gas distribution

    Directory of Open Access Journals (Sweden)

    Tejinder Pal Singh

    2015-01-01

    Full Text Available Purpose: Network design of the supply chain is an important and strategic aspect of logistics management. In this paper, we address the network design problem specific to packaged gases (cylinder supply chain. We propose an integrated framework that allows for the determination of the optimal facility locations, the filling plant production capacities, the inventory at plants and hubs, and the number of packages to be routed in primary and secondary transportation. Design/methodology/approach: We formulate the problem as a mixed integer program and then develop a decomposition approach to solve it. We illustrate the proposed framework with numerical examples from real-life packaged gases supply chain. The results show that the decomposition approach is effective in solving a broad range of problem sizes. Findings: The main finding of this paper is that decomposing the network design problem into two sub-problems is very effective to tackle the real-life large scale network design problems occurring in cylinder gas distribution by optimizing strategic and tactical decisions and approximating the operational decisions. We also benchmark the results from the decomposition approach by solving the complete packaged gases network design model for smaller test cases. Originality/value: The main contribution of our work is that it integrates supply chain network design decisions without fixing the fillings plant locations with inventory and resource allocation decisions required at the plants. We also consider the transportation costs for the entire supply chain including the transhipment costs among different facilities by deciding the replenishment frequency.

  2. Autonomic computing enabled cooperative networked design

    CERN Document Server

    Wodczak, Michal

    2014-01-01

    This book introduces the concept of autonomic computing driven cooperative networked system design from an architectural perspective. As such it leverages and capitalises on the relevant advancements in both the realms of autonomic computing and networking by welding them closely together. In particular, a multi-faceted Autonomic Cooperative System Architectural Model is defined which incorporates the notion of Autonomic Cooperative Behaviour being orchestrated by the Autonomic Cooperative Networking Protocol of a cross-layer nature. The overall proposed solution not only advocates for the inc

  3. CLUSTERING GSM INTERNET USAGE WITH SELF ORGANIZING MAPS

    Directory of Open Access Journals (Sweden)

    Ulas CELENK

    2013-01-01

    Full Text Available Abstract:In the recent years, the mobile internet usage has been common in daily life by the development of GSM technologies. The internet provides a very easy and flexible connection everywhere, when the users need to use internet. It supports messaging, media, finance and lots of services throughout its connection. Data can be transferred by constant quota values of internet users. For all new quota requests, charging system makes queries. There is some kind of performance problems occurs when the applications of quota is adjusted due to low level users. If the quotas are planned to provide internet services regarding intensive level internet users, then the low level users become aggrieved. The aim of this study is to set up dynamic quota values according to users behaviors and thus ensure high performance income using most used artificial neural network in grouping studies as SOM (Self-Organizing Maps

  4. Design and Management of Networked Information Systems

    DEFF Research Database (Denmark)

    Havn, Erling; Bansler, Jørgen P.

    1996-01-01

    In this paper, we present a newly started research project at the Center for Tele-Information at the Technical University of Denmark. The project focuses on the design and management of networked information systems, that is computer-based IS linked by a wide area network and supporting...... research questions:1. What is the essence of the new managerial theories and models and how do they define the role of telecommunications and IT in organizations?2. How are these organizational theories and models implemented in practice?3. How is the design and implementation of information systems...... and networks actually organized and carried out?4. What are the consequences for work content, skills, working conditions, etc.? The research project consists of a theoretical analysis of contemporary management theories as well as a number of in-depth case studies of firms engaged in the design...

  5. Occupational Exposure due to RF leakages within GSM Base ...

    African Journals Online (AJOL)

    ... electric field strength from all the cabins are 1.18 ± 1.07 V/m from GSM 1800 radio, 2.33 ± 3.82 V/m from GSM 900 radio and 1.77 ± 2.20 V/m from the Tx cables. The result of this study shows that the values were less than ICNIRP limits for occupational exposure. Key words: GSM, Base station, Exposure, Radiofrequency ...

  6. Targeting and design of chilled water network

    International Nuclear Information System (INIS)

    Foo, Dominic C.Y.; Ng, Denny K.S.; Leong, Malwynn K.Y.; Chew, Irene M.L.; Subramaniam, Mahendran; Aziz, Ramlan; Lee, Jui-Yuan

    2014-01-01

    Highlights: • Minimum flowrate targeting for chilled water network. • Mixed series/parallel configuration of chilled water-using units. • Integrated cooling and chilled water networks. - Abstract: Chilled water is a common cooling agent used in various industrial, commercial and institutional facilities. In conventional practice, chilled water is distributed via chilled water networks (CHWNs) in parallel configuration to provide required air conditioning and/or equipment cooling in the heating, ventilating and air conditioning (HVAC) system. In this paper, process integration approach based on pinch analysis technique is used to address energy efficiency issues in the CHWN system for grassroots design problem. Graphical and algebraic targeting techniques are developed to identify the minimum chilled water flowrate needed to remove a given amount of heat load from the CHWN. Doing this leads to higher chilled water return temperature and enhanced energy efficiency of the HVAC system. A recent proposed network design technique is extended to synthesize the CHWN in a mixed series/parallel configuration. A novel concept of integrated cooling and chilled water networks (IWN) is also proposed in this work, with its targeting and design techniques presented. Hypothetical examples and an industrial case study are solved to elucidate the proposed approaches

  7. Integrated network design and scheduling problems :

    Energy Technology Data Exchange (ETDEWEB)

    Nurre, Sarah G.; Carlson, Jeffrey J.

    2014-01-01

    We consider the class of integrated network design and scheduling problems. These problems focus on selecting and scheduling operations that will change the characteristics of a network, while being speci cally concerned with the performance of the network over time. Motivating applications of INDS problems include infrastructure restoration after extreme events and building humanitarian distribution supply chains. While similar models have been proposed, no one has performed an extensive review of INDS problems from their complexity, network and scheduling characteristics, information, and solution methods. We examine INDS problems under a parallel identical machine scheduling environment where the performance of the network is evaluated by solving classic network optimization problems. We classify that all considered INDS problems as NP-Hard and propose a novel heuristic dispatching rule algorithm that selects and schedules sets of arcs based on their interactions in the network. We present computational analysis based on realistic data sets representing the infrastructures of coastal New Hanover County, North Carolina, lower Manhattan, New York, and a realistic arti cial community CLARC County. These tests demonstrate the importance of a dispatching rule to arrive at near-optimal solutions during real-time decision making activities. We extend INDS problems to incorporate release dates which represent the earliest an operation can be performed and exible release dates through the introduction of specialized machine(s) that can perform work to move the release date earlier in time. An online optimization setting is explored where the release date of a component is not known.

  8. Assessment Of The Effectiveness Of Telecommunication Delivery Among Operators Of GSM In Ekiti State.

    Directory of Open Access Journals (Sweden)

    Olumuyiwa Oludare Fagbohun

    2017-11-01

    Full Text Available Data survey on the service delivery of the three principal Global System for Mobile Communications GSM Operators in Ekiti State Nigeria was conducted with a questionnaire administered among its citizens. Three locations Ado Ekiti 7o381 5o131 Ikere Ekiti 7o301 5o141 and Aramoko Ekiti 7o431 5o31were selected. Based on the responses from various subscribers using the networks the performance analyses of the operators were assessed using the descriptive statistical method. The assessment was based on the coverage area interconnectivity call quality number of subscribers growth and other supplementary services to assist the various GSM operators know the area of weakness and improve on the quality of the service delivery. It was discovered that the users have more complaints to offer with the performance generally rated below average and a need for fast and better network optimization for needed improvements for an effective telecommunication delivery.

  9. Node design in optical packet switched networks

    DEFF Research Database (Denmark)

    Nord, Martin

    2006-01-01

    The thesis discusses motivation, realisation and performance of the Optical Packet Switching (OPS) network paradigm. The work includes proposals for designs and methods to efficiently use both the wavelength- and time domain for contention resolution in asynchronous operation. The project has also...... adapting network performance to the different acceptable packet loss rate levels of supported applications, while improving overall bandwidth efficiency. The project has evaluated QoS differentiation methods and proposed schemes with improved efficiency, which also include jitter sensitivity as a Qo...... proposed parallel designs to overcome scalability constraints and to support migration scenarios. Furthermore, it has proposed and demonstrated optical input processing schemes for hybrids networks to simultaneously support OPS and Optical Circuit Switching. Quality of Service (QoS) differentiation enables...

  10. Robust network design for multispecies conservation

    Science.gov (United States)

    Ronan Le Bras; Bistra Dilkina; Yexiang Xue; Carla P. Gomes; Kevin S. McKelvey; Michael K. Schwartz; Claire A. Montgomery

    2013-01-01

    Our work is motivated by an important network design application in computational sustainability concerning wildlife conservation. In the face of human development and climate change, it is important that conservation plans for protecting landscape connectivity exhibit certain level of robustness. While previous work has focused on conservation strategies that result...

  11. Design and Management of Networked Information Systems

    DEFF Research Database (Denmark)

    Havn, Erling; Bansler, Jørgen P.

    1996-01-01

    In this paper, we present a newly started research project at the Center for Tele-Information at the Technical University of Denmark. The project focuses on the design and management of networked information systems, that is computer-based IS linked by a wide area network and supporting...... practices and work organization in different locations may make it very difficult to reach a common understanding of the purpose, design and use of the system; and (d) conflicts of interest and opportunistic behavior may impede or even confound the development of the system. We focus on the following four...... research questions:1. What is the essence of the new managerial theories and models and how do they define the role of telecommunications and IT in organizations?2. How are these organizational theories and models implemented in practice?3. How is the design and implementation of information systems...

  12. Design and implementation of a local computer network

    Energy Technology Data Exchange (ETDEWEB)

    Fortune, P. J.; Lidinsky, W. P.; Zelle, B. R.

    1977-01-01

    An intralaboratory computer communications network was designed and is being implemented at Argonne National Laboratory. Parameters which were considered to be important in the network design are discussed; and the network, including its hardware and software components, is described. A discussion of the relationship between computer networks and distributed processing systems is also presented. The problems which the network is designed to solve and the consequent network structure represent considerations which are of general interest. 5 figures.

  13. Time constrained liner shipping network design

    DEFF Research Database (Denmark)

    Karsten, Christian Vad; Brouer, Berit Dangaard; Desaulniers, Guy

    2017-01-01

    We present a mathematical model and a solution method for the liner shipping network design problem. The model takes into account coordination between vessels and transit time restrictions on the cargo flow. The solution method is an improvement heuristic, where an integer program is solved...... iteratively to perform moves in a large neighborhood search. Our improvement heuristic is applicable as a real-time decision support tool for a liner shipping company. It can be used to find improvements to the network when evaluating changes in operating conditions or testing different scenarios...

  14. Satellite communications network design and analysis

    CERN Document Server

    Jo, Kenneth Y

    2011-01-01

    This authoritative book provides a thorough understanding of the fundamental concepts of satellite communications (SATCOM) network design and performance assessments. You find discussions on a wide class of SATCOM networks using satellites as core components, as well as coverage key applications in the field. This in-depth resource presents a broad range of critical topics, from geosynchronous Earth orbiting (GEO) satellites and direct broadcast satellite systems, to low Earth orbiting (LEO) satellites, radio standards and protocols.This invaluable reference explains the many specific uses of

  15. BER and FER Prediction of Control and Traffic Channels for a GSM Type of Air-Interface

    DEFF Research Database (Denmark)

    Wigard, Jeroen; Nielsen, Thomas Toftegård; Michaelsen, Per Henrik

    1998-01-01

    Performance analysis of a mobile communications system is often done separately at network and at link level. It is difficult to study a modern mobile communications system like GSM analytically, due to the complexity. Hence simulations are used. It is desirable to include all link aspects...

  16. Synthesis and Design of Processing Networks

    DEFF Research Database (Denmark)

    Quaglia, Alberto; Sarup, Bent; Sin, Gürkan

    2012-01-01

    In this contribution, we propose an integrated business and engineering framework for synthesis and design of processing networks under uncertainty. In our framework, an adapted formulation of the transhipment problem is integrated with a superstructure, leading to a Stochastic Mixed Integer Non...... Linear Program (sMINLP), which is solved to determine simultaneously the optimal strategic and tactical decisions with respect to the processing network, the material flows, raw material and product portfolio. The framework allows time-effective and robust formulation, solution and analysis of largescale...... synthesis problems in presence of uncertainty parameters, contributing to broaden the range of application of stochastic programming and optimization to real industrial problems. The framework is applied to an industrial case study based on soybean processing, to identify the optimal processing network...

  17. Design Criteria For Networked Image Analysis System

    Science.gov (United States)

    Reader, Cliff; Nitteberg, Alan

    1982-01-01

    Image systems design is currently undergoing a metamorphosis from the conventional computing systems of the past into a new generation of special purpose designs. This change is motivated by several factors, notably among which is the increased opportunity for high performance with low cost offered by advances in semiconductor technology. Another key issue is a maturing in understanding of problems and the applicability of digital processing techniques. These factors allow the design of cost-effective systems that are functionally dedicated to specific applications and used in a utilitarian fashion. Following an overview of the above stated issues, the paper presents a top-down approach to the design of networked image analysis systems. The requirements for such a system are presented, with orientation toward the hospital environment. The three main areas are image data base management, viewing of image data and image data processing. This is followed by a survey of the current state of the art, covering image display systems, data base techniques, communications networks and software systems control. The paper concludes with a description of the functional subystems and architectural framework for networked image analysis in a production environment.

  18. Wireless sensor networks principles, design and applications

    CERN Document Server

    Yang, Shuang-Hua

    2014-01-01

    Wireless Sensor Networks presents the latest practical solutions to the design issues presented in wireless-sensor-network-based systems. Novel features of the text, distributed throughout, include workable solutions, demonstration systems and case studies of the design and application of wireless sensor networks (WSNs) based on the first-hand research and development experience of the author, and the chapters on real applications: building fire safety protection; smart home automation; and logistics resource management. Case studies and applications illustrate the practical perspectives of: ·         sensor node design; ·         embedded software design; ·         routing algorithms; ·         sink node positioning; ·         co-existence with other wireless systems; ·         data fusion; ·         security; ·         indoor location tracking; ·         integrating with radio-frequency identification; and ·         In...

  19. NIF ICCS network design and loading analysis

    International Nuclear Information System (INIS)

    Tietbohl, G; Bryant, R

    1998-01-01

    The National Ignition Facility (NIF) is housed within a large facility about the size of two football fields. The Integrated Computer Control System (ICCS) is distributed throughout this facility and requires the integration of about 40,000 control points and over 500 video sources. This integration is provided by approximately 700 control computers distributed throughout the NIF facility and a network that provides the communication infrastructure. A main control room houses a set of seven computer consoles providing operator access and control of the various distributed front-end processors (FEPs). There are also remote workstations distributed within the facility that allow provide operator console functions while personnel are testing and troubleshooting throughout the facility. The operator workstations communicate with the FEPs which implement the localized control and monitoring functions. There are different types of FEPs for the various subsystems being controlled. This report describes the design of the NIF ICCS network and how it meets the traffic loads that will are expected and the requirements of the Sub-System Design Requirements (SSDR's). This document supersedes the earlier reports entitled Analysis of the National Ignition Facility Network, dated November 6, 1996 and The National Ignition Facility Digital Video and Control Network, dated July 9, 1996. For an overview of the ICCS, refer to the document NIF Integrated Computer Controls System Description (NIF-3738)

  20. A Theory of Dark Network Design

    Science.gov (United States)

    2010-12-01

    Design, 47. 44 Ibid., 52–53. 21 the insurgents. The insurgent’s embeddedness in the population provides information superiority and decreases...specialization of tasks, formalization of procedures, formal training and indoctrination needed for the job , grouping of units, size of the units, action...jihad.103 The Salafists rely on their robust networks of trust-based relationships that provide a level embeddedness throughout the Muslim world

  1. Cognitive MAC designs for OSA networks

    CERN Document Server

    Derakhshani, Mahsa

    2014-01-01

    This SpringerBrief presents recent advances in the cognitive MAC designs for opportunistic spectrum access (OSA) networks. It covers the basic MAC functionalities and MAC enhancements of IEEE 802.11. Later chapters discuss the existing MAC protocols for OSA and classify them based on characteristic features. The authors provide new research in adaptive carrier sensing-based MAC designs tailored for OSA, which optimize spectrum utilization and ensure a peaceful coexistence of licensed and unlicensed systems. Analytically devised via optimization and game-theoretic approaches, these adaptive M

  2. Asynchronous design of Networks-on-Chip

    DEFF Research Database (Denmark)

    Sparsø, Jens

    2007-01-01

    The Network-on-chip concept has evolved as a solution to a broad range of problems related to the design of complex systems-on-chip (SoC) with tenths or hundreds of (heterogeneous) IP-cores. The paper introduces the NoC concept, identifies a range of possible timing organizations (globally-synchronous......, mesochronous, globally-asynchronous locally-synchronous and fully asynchronous), discusses the circuitry needed to implement these timing methodologies, and provides some implementation details for a couple of asynchronous NoCs designed at the Technical University of Denmark (DTU). The paper is written...

  3. Supply chain network design under uncertainty

    DEFF Research Database (Denmark)

    Govindan, Kannan; Fattahi, Mohammad; Keyvanshokooh, Esmaeil

    2017-01-01

    Supply chain network design (SCND) is one of the most crucial planning problems in supply chain management (SCM). Nowadays, design decisions should be viable enough to function well under complex and uncertain business environments for many years or decades. Therefore, it is essential to make...... programming, risk-averse stochastic programming, robust optimization, and fuzzy mathematical programming are explored in terms of mathematical modeling and solution approaches. Finally, the drawbacks and missing aspects of the related literature are highlighted and a list of potential issues for future...

  4. The Generalized Fixed-Charge Network Design Problem

    DEFF Research Database (Denmark)

    Thomadsen, Tommy; Stidsen, Thomas K.

    2007-01-01

    In this paper we present the generalized fixed-charge network design (GFCND) problem. The GFCND problem is an instance of the so-called generalized network design problems. In such problems, clusters instead of nodes have to be interconnected by a network. The network interconnecting the clusters...... is a fixed-charge network, and thus the GFCND problem generalizes the fixed-charge network design problem. The GFCND problem is related to the more general problem of designing hierarchical telecommunication networks. A mixed integer programming model is described and a branch-cut-and-price algorithm...

  5. Optimised Design and Analysis of All-Optical Networks

    DEFF Research Database (Denmark)

    Glenstrup, Arne John

    2002-01-01

    is developed, based on shortest-path algorithms and a comparatively new metaheuristic called simulated allocation. It is able to handle design of all-optical mesh networks with optical cross-connects, considers duct as well as fibre and node costs, and can also design protected networks. The method is assessed...... model for optical ring network design is presented. Manually designed real world ring networks are studied and it is found that the model can lead to cheaper network design. Moreover, ring and mesh network architectures are compared using real world costs, and it is found that optical cross......This PhD thesis presents a suite of methods for optimising design and for analysing blocking probabilities of all-optical networks. It thus contributes methodical knowledge to the field of computer assisted planning of optical networks. A two-stage greenfield optical network design optimiser...

  6. Speed Optimization in Liner Shipping Network Design

    DEFF Research Database (Denmark)

    Brouer, Berit Dangaard; Karsten, Christian Vad; Pisinger, David

    In the Liner Shipping Network Design Problem (LSNDP) services sail at a given speed throughout a round trip. In reality most services operate with a speed differentiated head- and back-haul, or even individual speeds on every sailing between two ports. The speed of a service is decisive for the b......In the Liner Shipping Network Design Problem (LSNDP) services sail at a given speed throughout a round trip. In reality most services operate with a speed differentiated head- and back-haul, or even individual speeds on every sailing between two ports. The speed of a service is decisive...... for the bunker consumption in the network as well as the transit time of cargo. Speed optimization has been considered for tramp shipping showing significant reductions in fuel consumption. However, variable speeds has not been considered for post optimization of the LSNDP, where speed optimization could result...... in changes to the cargo flow due to transit time restrictions as well as significant savings in fuel consumption and required vessel deployment due to a weekly frequency requirement. We present a heuristic method to calculate variable speed on a service and present computational results for improving...

  7. Peningkatan Kapasitas Sel Pada Sistem Seluler GSM

    Directory of Open Access Journals (Sweden)

    Alfin Hikmaturokhman

    2009-11-01

    Full Text Available Increasing cell capacity in GSM applied by several methods such as Fixed Channel Allocation (FCA, Channel Sharing, Channel Borrowing and Cell Splitting to solve the massive increasing of cellular users amount in the whole world. It necessary to calculate the number of the subscriber within each cell in a certain busy hour based on available channel capacity in order to serve the traffic capacity in a cell. In this work, we present calculations to compare cell capacity without increasing cell capacity method and cell capacity using increasing capacity methods. As a programming tool,  we used Borland Delphi 7. In addition, this simulation software added with comprehensive explanations, Erlang B Table, and graphics to make it easier and more efficient in analyzing.

  8. Enhancing Hohlraum Design with Artificial Neural Networks

    Science.gov (United States)

    Peterson, J. L.; Berzak Hopkins, L. F.; Humbird, K. D.; Brandon, S. T.; Field, J. E.; Langer, S. H.; Nora, R. C.; Spears, B. K.

    2017-10-01

    A primary goal of hohlraum design is to efficiently convert available laser power and energy to capsule drive, compression and ultimately fusion neutron yield. However, a major challenge of this multi-dimensional optimization problem is the relative computational expense of hohlraum simulations. In this work, we explore overcoming this obstacle with the use of artificial neural networks built off ensembles of hohlraum simulations. These machine learning systems emulate the behavior of full simulations in a fraction of the time, thereby enabling the rapid exploration of design parameters. We will demonstrate this technology with a search for modifications to existing high-yield designs that can maximize neutron production within NIF's current laser power and energy constraints. This work was performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344. LLNL-ABS-734401.

  9. GSM accessories now available from the CERN Stores

    CERN Multimedia

    Labo Telecom

    2001-01-01

    As of 1st October you can order and receive GSM accessories from the CERN stores like any other article. The CERN stores also manage GSM telephones but, for technical reasons, only the Labo Telecom shop (Building 31, Room S026) is able to make the standard sales, repairs and exchanges for authorised persons with a CERN subscription. Labo Telecom will thus become a specialist shop, open from 11 a.m. to 12 a.m., and will apply the usual rules and authorisation procedures of the stores. The paper form for requests for GSM subscriptions is being computerized and will be available on EDH in the near future.

  10. An Indoor Positioning Realisation for GSM using Fingerprinting and kNN

    Directory of Open Access Journals (Sweden)

    A. Anastasijević

    2013-06-01

    Full Text Available Positioning in public land mobile networks has become increasingly popular over the past years with the development of more sophisticated mobile equipment and standards. New services which rely on location information have been developed, such as emergency call localization, navigation, location sensitive commercials/ billing, etc. This paper investigates one practical realisation of an indoor positioning model for GSM (Global System for Mobile Communications networks, based on the received signal strength (RSS and fingerprinting method. The achieved results are well within international localization accuracy requirements for emergency services, confirming great potential of the approach.

  11. Key technologies of the server monitor and control system based on GSM short messages

    International Nuclear Information System (INIS)

    Chen Taiwei; Zhou Zhenliu; Liu Baoxu

    2007-01-01

    The network management based on SNMP protocol cannot effectively monitor and control application-system states and key-process states on the computer server. Furthermore, it needs the administrator's longtime surveillance. When the administrator leaves the computer, he can't receive the malfunction message in time. In this paper we present a server monitor and control system based on monitor agents and GSM short messages, introduce the key technology to realize it, and implement a model system in the real network environment. (authors)

  12. Performance of Adaptive Antennas in FH-GSM Using Conventional Beamforming

    DEFF Research Database (Denmark)

    Mogensen, Preben Elgaard; Leth-Espensen, P; Zetterberg, P.

    2000-01-01

    This paper presents the performance of adaptive antennas in a 1/3 reuse frequency hopping GSM network using conventional beamforming. It mainly focuses on C/I improvement for the purpose of capacity enhancement. The performance evaluation has been conducted by means of network computer simulations...... for low azimuth spread values. For large values of azimuth spread (relative to the antenna beamwidth), the performance gain is reduced significantly. For an azimuth spread of 10 degrees-12 degrees, which has been measured in urban macro-cellular environments, the C/I gain for M = 8 is reduced to approx. 5...

  13. Improved Intelligent Underlay-Overlay Combined with Frequency Hopping in GSM

    DEFF Research Database (Denmark)

    Wigard, Jeroen; Nielsen, Thomas Toftegaard; Mogensen, Preben Elgaard

    1997-01-01

    IUO (intelligent underlay-overlay) in a combination with random frequency hopping in GSM is analysed. Several improvements to the original IUO concept analysed in Nielsen et al. (1997) are introduced. With the improved IUO concept it is possible to load a network configuration consisting of 4...... regular frequency channels and 3 super layer channels almost to the hard blocking limit. A capacity gain of more than 40 percent compared to a one layer frequency hopping 3/9 reuse network has been found...

  14. Analisa Penerapan Teknologi UMTS Untuk Mengatasi Permasalahan Kapasitas Pada Jaringan 2G (GSM

    Directory of Open Access Journals (Sweden)

    Alfin Hikmaturokhman

    2012-05-01

    Full Text Available A high necesarry data service and bigger network capacity becomes a critical issue in the GSM network. One of the good and bad size parameter reference-quality GSM network can be viewed on the performance parameters MLSLOT Allocation Blocking. The default value for parameter MLSLOT Allocation Blocking are ? 40 % that the network is otherwise well. To overcome these problems it is applied to UMTS technology. The study was conducted to determine how the performance of the 2G PT Indosat Tbk. Before  and after the application of technology and how it compares to the performance of UMTS cellular network PT Indosat Tbk. before and after implementation of a UMTS network. In conducting this study the authors to collect the necessary data and did the interview if the supervisor does not know From the research the average value MLSlot Bocking Allocation has decreased, for the first sector decreased on average uplink 0.70% to 0.17% down 0.53%.The average downlink 26.49% to 14.98% down 11.51%. Sector 2 uplink average 0.24% to 0.00% down 0.24%, the average downlink 5.16% to 0.04% down 5.12%, Sector 3 uplink average 0.6% to 0.21% down 0.39%, the average downlink 23.99% to14.98%  down 9.01%.

  15. Impact of dynamic rate coding aspects of mobile phone networks on forensic voice comparison.

    Science.gov (United States)

    Alzqhoul, Esam A S; Nair, Balamurali B T; Guillemin, Bernard J

    2015-09-01

    Previous studies have shown that landline and mobile phone networks are different in their ways of handling the speech signal, and therefore in their impact on it. But the same is also true of the different networks within the mobile phone arena. There are two major mobile phone technologies currently in use today, namely the global system for mobile communications (GSM) and code division multiple access (CDMA) and these are fundamentally different in their design. For example, the quality of the coded speech in the GSM network is a function of channel quality, whereas in the CDMA network it is determined by channel capacity (i.e., the number of users sharing a cell site). This paper examines the impact on the speech signal of a key feature of these networks, namely dynamic rate coding, and its subsequent impact on the task of likelihood-ratio-based forensic voice comparison (FVC). Surprisingly, both FVC accuracy and precision are found to be better for both GSM- and CDMA-coded speech than for uncoded. Intuitively one expects FVC accuracy to increase with increasing coded speech quality. This trend is shown to occur for the CDMA network, but, surprisingly, not for the GSM network. Further, in respect to comparisons between these two networks, FVC accuracy for CDMA-coded speech is shown to be slightly better than for GSM-coded speech, particularly when the coded-speech quality is high, but in terms of FVC precision the two networks are shown to be very similar. Copyright © 2015 The Chartered Society of Forensic Sciences. Published by Elsevier Ireland Ltd. All rights reserved.

  16. Analysis and design of networked control systems

    CERN Document Server

    You, Keyou; Xie, Lihua

    2015-01-01

    This monograph focuses on characterizing the stability and performance consequences of inserting limited-capacity communication networks within a control loop. The text shows how integration of the ideas of control and estimation with those of communication and information theory can be used to provide important insights concerning several fundamental problems such as: ·         minimum data rate for stabilization of linear systems over noisy channels; ·         minimum network requirement for stabilization of linear systems over fading channels; and ·         stability of Kalman filtering with intermittent observations. A fundamental link is revealed between the topological entropy of linear dynamical systems and the capacities of communication channels. The design of a logarithmic quantizer for the stabilization of linear systems under various network environments is also extensively discussed and solutions to many problems of Kalman filtering with intermittent observations are de...

  17. Designing spaces for the networked learning landscape.

    Science.gov (United States)

    Nordquist, Jonas; Laing, Andrew

    2015-04-01

    The concept of the learning landscape is used to explore the range of learning environments needed at multiple scales to better align with changes in the medical education curriculum. Four key scales that correspond to important types of learning spaces are identified: the classroom, the building, the campus and the city. "In-between" spaces are identified as growing in importance given changing patterns of learning and the use of information technology. Technology is altering how learning takes place in a wider variety of types of spaces as it is interwoven into every aspect of learning. An approach to planning learning environments which recognizes the need to think of networks of learning spaces connected across multiple scales is proposed. The focus is shifted from singular spaces to networks of inter-connected virtual and digital environments. A schematic model comprising the networked learning landscape, intended as a guide to planning that emphasizes relationships between the changing curriculum and its alignment with learning environments at multiple scales is proposed in this work. The need for higher levels of engagement of faculty, administrators and students in defining the briefs for the design of new kinds of medical education environments is highlighted.

  18. Analysis and monitoring design for networks

    Energy Technology Data Exchange (ETDEWEB)

    Fedorov, V.; Flanagan, D.; Rowan, T.; Batsell, S.

    1998-06-01

    The idea of applying experimental design methodologies to develop monitoring systems for computer networks is relatively novel even though it was applied in other areas such as meteorology, seismology, and transportation. One objective of a monitoring system should always be to collect as little data as necessary to be able to monitor specific parameters of the system with respect to assigned targets and objectives. This implies a purposeful monitoring where each piece of data has a reason to be collected and stored for future use. When a computer network system as large and complex as the Internet is the monitoring subject, providing an optimal and parsimonious observing system becomes even more important. Many data collection decisions must be made by the developers of a monitoring system. These decisions include but are not limited to the following: (1) The type data collection hardware and software instruments to be used; (2) How to minimize interruption of regular network activities during data collection; (3) Quantification of the objectives and the formulation of optimality criteria; (4) The placement of data collection hardware and software devices; (5) The amount of data to be collected in a given time period, how large a subset of the available data to collect during the period, the length of the period, and the frequency of data collection; (6) The determination of the data to be collected (for instance, selection of response and explanatory variables); (7) Which data will be retained and how long (i.e., data storage and retention issues); and (8) The cost analysis of experiments. Mathematical statistics, and, in particular, optimal experimental design methods, may be used to address the majority of problems generated by 3--7. In this study, the authors focus their efforts on topics 3--5.

  19. Seismic stations with GSM telemetry for registration of quarry blasts

    Czech Academy of Sciences Publication Activity Database

    Brož, Milan; Číž, Radim; Málek, Jiří; Žanda, Libor

    2000-01-01

    Roč. 2000, 16 (118) (2000), s. 25-32 ISSN 1211-1910 Institutional research plan: CEZ:AV0Z3046908 Keywords : blasting * seismic station * GSM mobile modem Subject RIV: DC - Siesmology, Volcanology, Earth Structure

  20. gsmålsret for kommune i planlovssag

    DEFF Research Database (Denmark)

    Koch, Pernille Boye

    2007-01-01

    Artiklen er en kommentar til en højesteretsdom, der - i modsætning til hidtidig praksis - anerkender et søgsmål fra en kommune, som er blevet underkendt af en rekursinstans. Udgivelsesdato: juni 2007...

  1. Designing Networked Energy Infrastructures with Architectural Flexibility

    NARCIS (Netherlands)

    Melese, Y.G.; Heijnen, P.W.; Stikkelman, R.M.

    2014-01-01

    Development of networked energy infrastructures (like gas pipe networks), generally requires a significant amount of capital investment under resources, market and institutional uncertainties. Several independent suppliers and consumers are to be connected into these networks. However, the actual

  2. Design considerations for energy efficient, resilient, multi-layer networks

    DEFF Research Database (Denmark)

    Fagertun, Anna Manolova; Hansen, Line Pyndt; Ruepp, Sarah Renée

    2016-01-01

    This work investigates different network design considerations with respect to energy-efficiency, under green-field resilient multi-layer network deployment. The problem of energy efficient, reliable multi-layer network design is known to result in different trade-offs between key performance...... in multi-layer networks and performance measures such as network resource utilization, availability, agility to traffic fluctuations and energy consumption. A green-field network deployment scenario is considered, where different resiliency methods, design methodologies and grooming strategies are applied...

  3. Development of a GSM based radiation monitoring system (GRaMS)

    International Nuclear Information System (INIS)

    Saindane, Shashank S.; Suri, M.M.K.; Padmanabhan, N.; Pradeepkumar, K.S.; Sharma, D.N.

    2007-01-01

    Real-time measurements and the quick analysis of the data are of crucial importance during a radiological or nuclear emergency. To develop a timely response capability, the Radiation Safety Systems Division has launched a project to develop an advanced online measurement system for use in different threat scenarios, such as the release of radioactive materials to the environment during any nuclear or radiological accident. In order to meet this requirement a Global system for Mobile (GSM) based Radiation Monitoring system is designed and tested on field. It uses an energy compensated GM detector and is attached with commercially available Global Positioning System (GPS) for online acquisition of positional coordinates with time, and GSM modem for online data transfer. The equipment can be operated continuously while the vehicle is moving. The system is designed to provide measurement information, either raw data or analysis results, to the local database or to a remote database through a communication link. The system consumes ∼ 250 mA including the GPS and GSM enabling ∼ 30 hours of continuous radioactivity monitoring with a 12 Ah battery source. The system has been used in road based environmental radiation surveys carried out at various part of the country. With PC support, the system can map the radiological status online onto the map of the area being surveyed, to help decision-making on countermeasures during the survey and sending the online data at a remote station to enable the emergency managers to take appropriate decision. (author)

  4. Scheduling and Topology Design in Networks with Directional Antennas

    Science.gov (United States)

    2017-05-19

    Scheduling and Topology Design in Networks with Directional Antennas Thomas Stahlbuhk, Nathaniel M. Jones, Brooke Shrader Lincoln Laboratory...controllers must choose which pairs of nodes should communicate in order to establish a topology over which traffic can be sent. Additionally...interacting effects of topology design and transmission scheduling in wireless networks, in particular focusing on networks where nodes are divided into

  5. Designing and managing networks: possibilities and limitations for network management

    NARCIS (Netherlands)

    2005-01-01

    markdownabstract__Abstract__ If most decision-making processes aimed at solving societal problems have a network-like character, then a key question is how to deal with networks so that they can achieve valuable solutions to societal problems. Managing networks differs considerably from the

  6. Entropy Applications to Water Monitoring Network Design: A Review

    Directory of Open Access Journals (Sweden)

    Jongho Keum

    2017-11-01

    Full Text Available Having reliable water monitoring networks is an essential component of water resources and environmental management. A standardized process for the design of water monitoring networks does not exist with the exception of the World Meteorological Organization (WMO general guidelines about the minimum network density. While one of the major challenges in the design of optimal hydrometric networks has been establishing design objectives, information theory has been successfully adopted to network design problems by providing measures of the information content that can be deliverable from a station or a network. This review firstly summarizes the common entropy terms that have been used in water monitoring network designs. Then, this paper deals with the recent applications of the entropy concept for water monitoring network designs, which are categorized into (1 precipitation; (2 streamflow and water level; (3 water quality; and (4 soil moisture and groundwater networks. The integrated design method for multivariate monitoring networks is also covered. Despite several issues, entropy theory has been well suited to water monitoring network design. However, further work is still required to provide design standards and guidelines for operational use.

  7. New types of subscriptions for CERN GSM

    CERN Multimedia

    IT Department

    2010-01-01

    A recent renegotiation of our commercial conditions with our mobile telephony operator allows us today to deploy new GSM mobile services, reduce communication costs, as well as put in place a new subscription system. First of all, the "email to SMS" service has already been extended to all Swiss numbers. This service allows you to send SMS messages (Short Message Service) to any Swiss mobile telephone from your CERN e-mail account. For further details, please refer to the web site http://cern.ch/sms. The sending of MMS messages (Multi-media Message Service) will be activated by default on all CERN subscriptions by the end of March 2010. This service allows users to attach to a text message an image, a video or an audio recording. All the necessary details for configuring this new service on CERN mobile phones will be published on the web site http://cern.ch/mms. Concerning mobile service costs, new rates have been put in place since 1st January 2010. All tariffs have dramatically decrea...

  8. Bistable responses in bacterial genetic networks: Designs and dynamical consequences

    Science.gov (United States)

    Tiwari, Abhinav; Ray, J. Christian J.; Narula, Jatin; Igoshin, Oleg A.

    2011-01-01

    A key property of living cells is their ability to react to stimuli with specific biochemical responses. These responses can be understood through the dynamics of underlying biochemical and genetic networks. Evolutionary design principles have been well studied in networks that display graded responses, with a continuous relationship between input signal and system output. Alternatively, biochemical networks can exhibit bistable responses so that over a range of signals the network possesses two stable steady states. In this review, we discuss several conceptual examples illustrating network designs that can result in a bistable response of the biochemical network. Next, we examine manifestations of these designs in bacterial master-regulatory genetic circuits. In particular, we discuss mechanisms and dynamic consequences of bistability in three circuits: two-component systems, sigma-factor networks, and a multistep phosphorelay. Analyzing these examples allows us to expand our knowledge of evolutionary design principles for networks with bistable responses. PMID:21385588

  9. Hydrological Monitoring System Design and Implementation Based on IOT

    Science.gov (United States)

    Han, Kun; Zhang, Dacheng; Bo, Jingyi; Zhang, Zhiguang

    In this article, an embedded system development platform based on GSM communication is proposed. Through its application in hydrology monitoring management, the author makes discussion about communication reliability and lightning protection, suggests detail solutions, and also analyzes design and realization of upper computer software. Finally, communication program is given. Hydrology monitoring system from wireless communication network is a typical practical application of embedded system, which has realized intelligence, modernization, high-efficiency and networking of hydrology monitoring management.

  10. A quantitative approach to static sensor network design

    DEFF Research Database (Denmark)

    Pedersen, Martin Wæver; Burgess, Greg; Weng, Kevin C.

    2014-01-01

    Static sensor networks to observe animals are widely used in ecological, management and conservation research, but quantitative methods for designing these networks are underdeveloped. In the context of aquatic systems, we present a method for quasi-optimal network design, which accounts for bloc......Static sensor networks to observe animals are widely used in ecological, management and conservation research, but quantitative methods for designing these networks are underdeveloped. In the context of aquatic systems, we present a method for quasi-optimal network design, which accounts...... for blocking of detections by obstacles, horizontal and vertical movement behaviour of the target animals, and type of research question (is the network intended for estimation of detailed movement or home range?). Optimal design is defined as the sensor configuration that maximizes the expected number...

  11. Topology design and performance analysis of an integrated communication network

    Science.gov (United States)

    Li, V. O. K.; Lam, Y. F.; Hou, T. C.; Yuen, J. H.

    1985-01-01

    A research study on the topology design and performance analysis for the Space Station Information System (SSIS) network is conducted. It is begun with a survey of existing research efforts in network topology design. Then a new approach for topology design is presented. It uses an efficient algorithm to generate candidate network designs (consisting of subsets of the set of all network components) in increasing order of their total costs, and checks each design to see if it forms an acceptable network. This technique gives the true cost-optimal network, and is particularly useful when the network has many constraints and not too many components. The algorithm for generating subsets is described in detail, and various aspects of the overall design procedure are discussed. Two more efficient versions of this algorithm (applicable in specific situations) are also given. Next, two important aspects of network performance analysis: network reliability and message delays are discussed. A new model is introduced to study the reliability of a network with dependent failures. For message delays, a collection of formulas from existing research results is given to compute or estimate the delays of messages in a communication network without making the independence assumption. The design algorithm coded in PASCAL is included as an appendix.

  12. Indoor Radio Planning A Practical Guide for GSM, DCS, UMTS, HSPA and LTE

    CERN Document Server

    Tolstrup, Morten

    2011-01-01

    Why is indoor coverage needed, and how it is best implemented? As the challenge of providing higher data speeds and quality for mobile applications intensifies, ensuring adequate in-building and tunnel coverage and capacity is increasingly important. A unique, single-source reference on the theoretical and practical knowledge behind indoor and tunnel radio planning, Indoor Radio Planning, Second Edition provides an overview of mobile networks systems and coverage solutions with GSM, UMTS, HSPA and LTE cellular systems technologies as a backdrop. All of the available solutions, from basic passi

  13. Networked Collaboration Canvas : How can Service Design facilitate Networked Collaboration?

    NARCIS (Netherlands)

    L. Henze; I.J. Mulder

    2014-01-01

    Whereas products and services are growing in complexity, industry needs to expand their networks to include expertise from other fields than their own. Consequently, innovation activities more and more take place in highly dynamic network environments, mixing people and parties, models, interests,

  14. Network Design for Container Shipping Using Cutting Planes

    DEFF Research Database (Denmark)

    The network design problem in container shipping is of increasing importance in the strongly competitive markets where potential cost reductions are of the utmost importance. We combine the network design and fleet assignment problem into a mixed integer linear programming model minimizing...... the overall cost. The real-life container shipping network design problem differs in several ways from the standard network design problem. Examples of these differences are the cyclic routes of vessels and the fact that a route is continuously sailed for a given forecast period. To model these real...

  15. Solving network design problems via decomposition, aggregation and approximation

    CERN Document Server

    Bärmann, Andreas

    2016-01-01

    Andreas Bärmann develops novel approaches for the solution of network design problems as they arise in various contexts of applied optimization. At the example of an optimal expansion of the German railway network until 2030, the author derives a tailor-made decomposition technique for multi-period network design problems. Next, he develops a general framework for the solution of network design problems via aggregation of the underlying graph structure. This approach is shown to save much computation time as compared to standard techniques. Finally, the author devises a modelling framework for the approximation of the robust counterpart under ellipsoidal uncertainty, an often-studied case in the literature. Each of these three approaches opens up a fascinating branch of research which promises a better theoretical understanding of the problem and an increasing range of solvable application settings at the same time. Contents Decomposition for Multi-Period Network Design Solving Network Design Problems via Ag...

  16. Designing inclusion and exclusion in labour market governance networks

    DEFF Research Database (Denmark)

    Damgaard, Bodil

    networks and do not adequately explain who actually gets access to these networks. Instead I argue that we need to analyse actions taken consciously and deliberately to design inclusion – as well as exclusion – in governance networks, i.e. we need to bring agency into the analysis and analyse...

  17. Hierarchical Ring Network Design Using Branch-and-Price

    DEFF Research Database (Denmark)

    Thomadsen, Tommy; Stidsen, Thomas K.

    2005-01-01

    link establishment costs and the link capacity costs into account. Hierarchical ring network design problems combines the following optimization problems: Clustering, hub selection, metro ring design, federal ring design and routing problems. In this paper a branch-and-price algorithm is presented...... for jointly solving the clustering problem, the metro ring design problem and the routing problem. Computational results are given for networks with up to 36 nodes....

  18. Topology Design for Directional Range Extension Networks with Antenna Blockage

    Science.gov (United States)

    2017-03-19

    Topology Design for Directional Range Extension Networks with Antenna Blockage Thomas Shake MIT Lincoln Laboratory shake@ll.mit.edu Abstract...associated electronics into small aircraft to perform such range extension. In particular, the paper examines trade-offs in network topology design...aircraft, and the topology characteristics of the aerial relay network. The analysis suggests that low-degree air topologies such as rings and strings

  19. The Design, Experience and Practice of Networked Learning

    DEFF Research Database (Denmark)

    . The Design, Experience and Practice of Networked Learning will prove indispensable reading for researchers, teachers, consultants, and instructional designers in higher and continuing education; for those involved in staff and educational development, and for those studying post graduate qualifications...... in learning and teaching. This, the second volume in the Springer Book Series on Researching Networked Learning, is based on a selection of papers presented at the 2012 Networked Learning Conference held in Maastricht, The Netherlands....

  20. A genetic algorithm for solving supply chain network design model

    Science.gov (United States)

    Firoozi, Z.; Ismail, N.; Ariafar, S. H.; Tang, S. H.; Ariffin, M. K. M. A.

    2013-09-01

    Network design is by nature costly and optimization models play significant role in reducing the unnecessary cost components of a distribution network. This study proposes a genetic algorithm to solve a distribution network design model. The structure of the chromosome in the proposed algorithm is defined in a novel way that in addition to producing feasible solutions, it also reduces the computational complexity of the algorithm. Computational results are presented to show the algorithm performance.

  1. Design and Realization of Network Teaching System

    Directory of Open Access Journals (Sweden)

    Ji Shan Shan

    2016-01-01

    Full Text Available Since 21 century, with the wide spread in family and public, network has been applied in many new fields, and the application in classes is of no exception. In traditional education, teachers give lessons to students face to face. Hence, the teaching quality depends largely on the quality and initiative of the individual teacher. However, the serious disadvantages of this mode are that teachers completely dominate the classroom and may ignore the subjective cognition role of the students, which may be bad for the growth of creativity and the innovative thinking ability. Obviously, traditional education mode cannot meet the requirements of the this new era which leads to the booming developing tendency of the network. As a new teaching measure, scientifically combining modern information technology and teaching practice, network teaching not only changes the traditional education by the means and form, but even also gives new meanings to teaching concept, process, method as well as teacher-student role and other deep levels. With the help of network teaching system, on-line classroom learning, relevant information systematization, standardization and automation, this system provides students with an efficient online learning method with high quality. This also helps to solve the disadvantages of the traditional teaching mode and promote the teaching methods to a new stage. It improves the network teaching platform, enriches the network teaching resources, and establishes a network teaching system, so as to improve information quality of teachers and students and assist in improving teaching quality of schools.

  2. Designing Industrial Networks Using Ecological Food Web Metrics.

    Science.gov (United States)

    Layton, Astrid; Bras, Bert; Weissburg, Marc

    2016-10-18

    Biologically Inspired Design (biomimicry) and Industrial Ecology both look to natural systems to enhance the sustainability and performance of engineered products, systems and industries. Bioinspired design (BID) traditionally has focused on a unit operation and single product level. In contrast, this paper describes how principles of network organization derived from analysis of ecosystem properties can be applied to industrial system networks. Specifically, this paper examines the applicability of particular food web matrix properties as design rules for economically and biologically sustainable industrial networks, using an optimization model developed for a carpet recycling network. Carpet recycling network designs based on traditional cost and emissions based optimization are compared to designs obtained using optimizations based solely on ecological food web metrics. The analysis suggests that networks optimized using food web metrics also were superior from a traditional cost and emissions perspective; correlations between optimization using ecological metrics and traditional optimization ranged generally from 0.70 to 0.96, with flow-based metrics being superior to structural parameters. Four structural food parameters provided correlations nearly the same as that obtained using all structural parameters, but individual structural parameters provided much less satisfactory correlations. The analysis indicates that bioinspired design principles from ecosystems can lead to both environmentally and economically sustainable industrial resource networks, and represent guidelines for designing sustainable industry networks.

  3. Network Design Guidance for the Global Special Operations Forces Network

    Science.gov (United States)

    2014-12-01

    and interagency cooperation integrated on a digitally networked battlefield. 35 Ibid., 7. The indirect approach is defined as “long-term efforts to...population between 80,000 and 100,000 with a postwar Serb population of less than 5 percent.181 The taxation and banking systems were nonexistent

  4. Designing Network-based Business Model Ontology

    DEFF Research Database (Denmark)

    Hashemi Nekoo, Ali Reza; Ashourizadeh, Shayegheh; Zarei, Behrouz

    2015-01-01

    is going to propose e-business model ontology from the network point of view and its application in real world. The suggested ontology for network-based businesses is composed of individuals` characteristics and what kind of resources they own. also, their connections and pre-conceptions of connections...... such as shared-mental model and trust. However, it mostly covers previous business model elements. To confirm the applicability of this ontology, it has been implemented in business angel network and showed how it works....

  5. [Signaling network-based functional cell design].

    Science.gov (United States)

    Ju, Jianqi; Wei, Ping

    2017-03-25

    Cellular signaling networks act as the central processor to deal with environmental signals and regulate cell function, and determine cell fate. Using synthetic biology approach to engineer cell signaling networks is crucial for ultimately constructing man-made "cell machines". Cellular signaling networks can encode sophisticated cell information by processing quantitatively signaling dynamics, which enables multi-dimensional regulation of functional sub-circuits. Here, we first review the research progresses on the signaling coding mechanisms; and then elaborate the methodologies and applications of cells signaling engineering; finally, we envision that signaling-based cell engineering are important for the increasingly-complicated next generation synthetic biology.

  6. Topological Effects and Performance Optimization in Transportation Continuous Network Design

    Directory of Open Access Journals (Sweden)

    Jianjun Wu

    2014-01-01

    Full Text Available Because of the limitation of budget, in the planning of road works, increased efforts should be made on links that are more critical to the whole traffic system. Therefore, it would be helpful to model and evaluate the vulnerability and reliability of the transportation network when the network design is processing. This paper proposes a bilevel transportation network design model, in which the upper level is to minimize the performance of the network under the given budgets, while the lower level is a typical user equilibrium assignment problem. A new solution approach based on particle swarm optimization (PSO method is presented. The topological effects on the performance of transportation networks are studied with the consideration of three typical networks, regular lattice, random graph, and small-world network. Numerical examples and simulations are presented to demonstrate the proposed model.

  7. Assessment of students' GSM phone use pattern at the faculty of ...

    African Journals Online (AJOL)

    The study assessed Students' GSM phone use pattern at Faculty of Education, University of Uyo. The specific objectives are to determine the gender and other characteristic of GSM phone owners among the students, ascertain the features of GSM phones that students preferred to use and to assess the use to which ...

  8. Designing optimal greenhouse gas monitoring networks for Australia

    Science.gov (United States)

    Ziehn, T.; Law, R. M.; Rayner, P. J.; Roff, G.

    2016-01-01

    Atmospheric transport inversion is commonly used to infer greenhouse gas (GHG) flux estimates from concentration measurements. The optimal location of ground-based observing stations that supply these measurements can be determined by network design. Here, we use a Lagrangian particle dispersion model (LPDM) in reverse mode together with a Bayesian inverse modelling framework to derive optimal GHG observing networks for Australia. This extends the network design for carbon dioxide (CO2) performed by Ziehn et al. (2014) to also minimise the uncertainty on the flux estimates for methane (CH4) and nitrous oxide (N2O), both individually and in a combined network using multiple objectives. Optimal networks are generated by adding up to five new stations to the base network, which is defined as two existing stations, Cape Grim and Gunn Point, in southern and northern Australia respectively. The individual networks for CO2, CH4 and N2O and the combined observing network show large similarities because the flux uncertainties for each GHG are dominated by regions of biologically productive land. There is little penalty, in terms of flux uncertainty reduction, for the combined network compared to individually designed networks. The location of the stations in the combined network is sensitive to variations in the assumed data uncertainty across locations. A simple assessment of economic costs has been included in our network design approach, considering both establishment and maintenance costs. Our results suggest that, while site logistics change the optimal network, there is only a small impact on the flux uncertainty reductions achieved with increasing network size.

  9. Optimal design of network distribution systems

    Directory of Open Access Journals (Sweden)

    U. Passy

    2003-12-01

    Full Text Available The problem of finding the optimal distribution of pressure drop over a network is solved via an unconstrained gradient type algorithm. The developed algorithm is computationally attractive. Problems with several hundred variables and constraints were solved.

  10. Imbibition well stimulation via neural network design

    Science.gov (United States)

    Weiss, William

    2007-08-14

    A method for stimulation of hydrocarbon production via imbibition by utilization of surfactants. The method includes use of fuzzy logic and neural network architecture constructs to determine surfactant use.

  11. Design Management in the Textile Industry - A Network Perspective

    DEFF Research Database (Denmark)

    Christensen, Poul Rind; Bang, Anne Louise

    In this paper we explore textile design activities and textile design management from an industrial network perspective. The textile industry is probably one of the most globalized manufacturing industries in the world and thus one of the most dispersed industries on the globe. Most studies on de...... management in order to maintain the relationships in their network of customers and suppliers....... on design management are framed inside the organisational context of the firm. In this study the role and practice of textile design is addressed in perspective of the global textile production network. The empirical data stems from six case studies exploring how different types of enterprises are organised......In this paper we explore textile design activities and textile design management from an industrial network perspective. The textile industry is probably one of the most globalized manufacturing industries in the world and thus one of the most dispersed industries on the globe. Most studies...

  12. Designing a Rational Distribution Network for Trading Companies

    Directory of Open Access Journals (Sweden)

    Dybskaya V. V.

    2017-09-01

    Full Text Available This article considers the modern methods and approaches to design the company’s distribution network. The authors point out the relevance of this problem for the modern trading and manufacturing companies, give examples of the strategic goal setting of the company in the logistics network reorganization, and the benchmarks of possible economic effects of its conduction. The work reviews the scientific articles of contemporary American, European and Russian authors devoted to the approaches, concerning the implementation of projects for designing a distribution network, methods and models for its optimization. The article concludes that there is no single “language” and an approach to design the logistics networks, with a proper level of detail that takes into account the strategic features and industry specificity of the certain company. The authors propose an algorithm for designing a rational distribution network.

  13. On the Adaptive Design Rules of Biochemical Networks in Evolution

    Directory of Open Access Journals (Sweden)

    Bor-Sen Chen

    2007-01-01

    Full Text Available Biochemical networks are the backbones of physiological systems of organisms. Therefore, a biochemical network should be sufficiently robust (not sensitive to tolerate genetic mutations and environmental changes in the evolutionary process. In this study, based on the robustness and sensitivity criteria of biochemical networks, the adaptive design rules are developed for natural selection in the evolutionary process. This will provide insights into the robust adaptive mechanism of biochemical networks in the evolutionary process. We find that if a mutated biochemical network satisfies the robustness and sensitivity criteria of natural selection, there is a high probability for the biochemical network to prevail during natural selection in the evolutionary process. Since there are various mutated biochemical networks that can satisfy these criteria but have some differences in phenotype, the biochemical networks increase their diversities in the evolutionary process. The robustness of a biochemical network enables co-option so that new phenotypes can be generated in evolution. The proposed robust adaptive design rules of natural selection gain much insight into the evolutionary mechanism and provide a systematic robust biochemical circuit design method of biochemical networks for biotechnological and therapeutic purposes in the future.

  14. Determination of Safety Distance for Installing GSM Mast in ...

    African Journals Online (AJOL)

    ADOWIE PERE

    DANLADI, A; GAYA, GK; ALIYU, BM; STEPHEN, M; MICHAEL, Y;. NA'IMU, A. Department of Pure and Applied Physics, Adamawa State University, Mubi, Nigeria. *E-mail: deshalangs3g@yahoo.com; Phone: +2347063853164. ABSTRACT: Global System for Mobile Communication (GSM) technology is one of the fastest ...

  15. Determination of GSM Signal Penetration Loss in some Selected ...

    African Journals Online (AJOL)

    Determination of GSM Signal Penetration Loss in some Selected Buildings in Rivers State, Nigeria. ... Nigerian Journal of Technology ... are governed by the mechanism of reflection, refraction, diffraction and scattering of signal propagation through buildings which are dependent on the material of the building structure.

  16. Level of Radiofrequency (RF) Radiations from GSM Base Stations ...

    African Journals Online (AJOL)

    Levels of radiofrequency radiations around two global systems for mobile communication (GSM) base stations located in the vicinity of a residential quarter and workplace complex were measured. The effects of the radiofrequency radiations on albino mice placed in exposure cages and located around the base stations ...

  17. Android App Based Vehicle Tracking Using GPS And GSM

    Directory of Open Access Journals (Sweden)

    Jessica Saini

    2017-09-01

    Full Text Available Global Positioning System GPS is used in numerous applications in todays world. A real time vehicle tracking system using the GPS technology is proposed in this paper. The project Android App based Vehicle Tracking Using GSM AND GPRS mainly focuses in tracking the location of the vehicle on which the device has been installed. It will then send the data in the form of latitude and longitude coordinates through SMS on the users mobile where the coordinates will be plotted in the Android app automatically. Initially the GPS installed in the device takes input from the satellite and stores it in the microcontrollers buffer. In order to track the vehicle the mobile user has to call on the SIM number that is registered in the GSM module of the device. Once the call is received the device authenticates the calling number. If authenticated the location of the vehicle is sent to the registered mobile number in the form of SMS. After sending the message the GSM is deactivated and the GPS is activated again. The coordinates of the location received in the SMS can be viewed on the android app. The hardware part described in the paper comprises of GPRS GSM module LCD to view the coordinates ATMega Microcontroller MAX 232 Arduino RS232 and relay.

  18. Indoor Localisation Based on GSM Signals: Multistorey Building Study

    Directory of Open Access Journals (Sweden)

    Rafał Górak

    2016-01-01

    Full Text Available Among the accurate indoor localisation systems that are using WiFi, Bluetooth, or infrared technologies, the ones that are based on the GSM rely on a stable external infrastructure that can be used even in an emergency. This paper presents an accurate GSM indoor localisation system that achieves a median error of 4.39 metres in horizontal coordinates and up to 64 percent accuracy in floor prediction (for 84 percent of cases the floor prediction is mistaken by not more than a single floor. The test and reference measurements were made inside a six-floor academic building, with an irregular shape, whose dimensions are around 50 metres by 70 metres. The localisation algorithm uses GSM signal readings from the 7 strongest cells available in the GSM standard (or fewer, if fewer than 7 are available. We estimate the location by a three-step method. Firstly, we propose a point localisation solution (i.e., localisation based on only one measurement. Then, by applying the central tendency filters and the Multilayer Perceptron, we build a localisation system that uses a sequence of estimations of current and past locations. We also discuss major accuracy factors such as the number of observed signals or the types of spaces in the building.

  19. Esimene GSM-võrk Radiolinjal / Tiina Kass

    Index Scriptorium Estoniae

    Kass, Tiina

    2004-01-01

    Ilmunud ka: Delovõje Vedomosti : Infotehnologija 21. apr. lk. 1. Mobiilsideoperaatori Radiolinja Eesti AS-i juht Ants Viira ettevõtte asutamisest 1994. aastal, GSM-võrgu avamisest ja konkurentsist EMT AS-iga. Lisa: Radiolinja kõnehind pole 10 aastaga kuigivõrd muutunud. Vt. samas: Suhkru ja metalliärikad olid esimesed mobiiliomanikud

  20. Vehicle Theft Identification and Intimation Using GSM & IOT

    Science.gov (United States)

    Eswar Kumar, M.; Thippa Reddy, G.; Sudheer, K.; Reddy, M. Praveen Kumar; Kaluri, Rajesh; Singh Rajput, Dharmendra; Lakshmanna, Kuruva

    2017-11-01

    Internet of Things is the most predominant innovation associates the things through web. IoT is a technology which interfaces things from different places on the planet. Home mechanization is a wide range innovation in IoT technology on the planet. Home automation constitutes in security issues, controlling gadgets and so on. In existing model, the vehicle theft is distinguished and controlled by physically with GSM module. Furthermore, there are a few in controlling the vehicle is major issue for owner from theft. Here in this paper a technique described to overcome issue of existing one. In this the vehicle is identified, controlled and connected updates with Internet in a simple way. By utilization of AT commands of GSM module a message will be send to the owner that the vehicle is recognized. Action can be taken by sending a reply to GSM module to stop motor of vehicle. Arduino uno board is used to interface the GSM and engine of vehicle with appropriate sensors. Visual studio, Arduino uno are the programming software used to outline this application.

  1. Rapid Sampling of Hydrogen Bond Networks for Computational Protein Design.

    Science.gov (United States)

    Maguire, Jack B; Boyken, Scott E; Baker, David; Kuhlman, Brian

    2018-04-20

    Hydrogen bond networks play a critical role in determining the stability and specificity of biomolecular complexes, and the ability to design such networks is important for engineering novel structures, interactions, and enzymes. One key feature of hydrogen bond networks that makes them difficult to rationally engineer is that they are highly cooperative and are not energetically favorable until the hydrogen bonding potential has been satisfied for all buried polar groups in the network. Existing computational methods for protein design are ill-equipped for creating these highly cooperative networks because they rely on energy functions and sampling strategies that are focused on pairwise interactions. To enable the design of complex hydrogen bond networks, we have developed a new sampling protocol in the molecular modeling program Rosetta that explicitly searches for sets of amino acid mutations that can form self-contained hydrogen bond networks. For a given set of designable residues, the protocol often identifies many alternative sets of mutations/networks, and we show that it can readily be applied to large sets of residues at protein-protein interfaces or in the interior of proteins. The protocol builds on a recently developed method in Rosetta for designing hydrogen bond networks that has been experimentally validated for small symmetric systems but was not extensible to many larger protein structures and complexes. The sampling protocol we describe here not only recapitulates previously validated designs with performance improvements but also yields viable hydrogen bond networks for cases where the previous method fails, such as the design of large, asymmetric interfaces relevant to engineering protein-based therapeutics.

  2. A matheuristic for the liner shipping network design problem

    DEFF Research Database (Denmark)

    Brouer, Berit Dangaard; Desaulniers, Guy

    2012-01-01

    for revenue and transshipment of cargo along with in/decrease of vessel- and operational cost for the current solution. The evaluation functions may be used by heuristics in general to evaluate changes to a network design without solving a large scale multicommodity flow problem.......We present a matheuristic, an integer programming based heuristic, for the Liner Shipping Network Design Problem. The heuristic applies a greedy construction heuristic based on an interpretation of the liner shipping network design problem as a multiple quadratic knapsack problem. The construction...

  3. Service network design of bike sharing systems analysis and optimization

    CERN Document Server

    Vogel, Patrick

    2016-01-01

    This monograph presents a tactical planning approach for service network design in metropolitan areas. Designing the service network requires the suitable aggregation of demand data as well as the anticipation of operational relocation decisions. To this end, an integrated approach of data analysis and mathematical optimization is introduced. The book also includes a case study based on real-world data to demonstrate the benefit of the proposed service network design approach. The target audience comprises primarily research experts in the field of traffic engineering, but the book may also be beneficial for graduate students.

  4. Designing communication and remote controlling of virtual instrument network system

    International Nuclear Information System (INIS)

    Lei Lin; Wang Houjun; Zhou Xue; Zhou Wenjian

    2005-01-01

    In this paper, a virtual instrument network through the LAN and finally remote control of virtual instruments is realized based on virtual instrument and LabWindows/CVI software platform. The virtual instrument network system is made up of three subsystems. There are server subsystem, telnet client subsystem and local instrument control subsystem. This paper introduced virtual instrument network structure in detail based on LabWindows. Application procedure design of virtual instrument network communication, the Client/the programming mode of the server, remote PC and server communication far realizing, the control power of the workstation is transmitted, server program and so on essential technical were introduced. And virtual instruments network may connect to entire Internet on. Above-mentioned technology, through measuring the application in the electronic measurement virtual instrument network that is already built up, has verified the actual using value of the technology. Experiment and application validate that this design is resultful

  5. Synthesis and Design of Integrated Process and Water Networks

    DEFF Research Database (Denmark)

    Handani, Zainatul B.; Quaglia, Alberto; Gani, Rafiqul

    2015-01-01

    This work presents the development of a systematic framework for a simultaneous synthesis and design of process and water networks using the superstructure-based optimization approach. In this framework, a new superstructure combining both networks is developed by attempting to consider all...... the values of contaminants in the wastewater stream into wastewater characterizations. The systematic approach is used to manage the complexity of the problem by solving simultaneously process synthesis and water synthesis network problems with respect to environment, economics and sustainability...

  6. Professional Learning Networks Designed for Teacher Learning

    Science.gov (United States)

    Trust, Torrey

    2012-01-01

    In the information age, students must learn to navigate and evaluate an expanding network of information. Highly effective teachers model this process of information analysis and knowledge acquisition by continually learning through collaboration, professional development, and studying pedagogical techniques and best practices. Many teachers have…

  7. Analysis and Design of Complex Networks

    Science.gov (United States)

    2014-12-02

    LUI, BRUNO RIBEIRO, DON TOWSLEY, JUNZHOU ZHAO, XIAOHONG GUAN. Efficiently Estimating Motif Statistics of Large Networks, ACM Transactions on...Anantharam. Prediction over countable alphabets, Conference on Inforamtion Sciences and Systems. 21- MAR -12, . : , Varun Jog, Venkat Anantharam. The... Bruno Ribeiro, David Jensen, Don Towsley, Benyuan Liu, Hua Jiang, Xiaodong Wang. Online Dating Recommendations: Matching Markets and Learning

  8. Rational design of functional and tunable oscillating enzymatic networks

    Science.gov (United States)

    Semenov, Sergey N.; Wong, Albert S. Y.; van der Made, R. Martijn; Postma, Sjoerd G. J.; Groen, Joost; van Roekel, Hendrik W. H.; de Greef, Tom F. A.; Huck, Wilhelm T. S.

    2015-02-01

    Life is sustained by complex systems operating far from equilibrium and consisting of a multitude of enzymatic reaction networks. The operating principles of biology's regulatory networks are known, but the in vitro assembly of out-of-equilibrium enzymatic reaction networks has proved challenging, limiting the development of synthetic systems showing autonomous behaviour. Here, we present a strategy for the rational design of programmable functional reaction networks that exhibit dynamic behaviour. We demonstrate that a network built around autoactivation and delayed negative feedback of the enzyme trypsin is capable of producing sustained oscillating concentrations of active trypsin for over 65 h. Other functions, such as amplification, analog-to-digital conversion and periodic control over equilibrium systems, are obtained by linking multiple network modules in microfluidic flow reactors. The methodology developed here provides a general framework to construct dissipative, tunable and robust (bio)chemical reaction networks.

  9. Multimodal network design for sustainable household plastic recycling

    NARCIS (Netherlands)

    Bing Xiaoyun, Xiaoyun; Groot, J.J.; Bloemhof, J.M.; Vorst, van der J.G.A.J.

    2013-01-01

    Purpose – This research studies a plastic recycling system from a reverse logistics angle and investigates the potential benefits of a multimodality strategy to the network design of plastic recycling. This research aims to quantify the impact of multimodality on the network, to provide decision

  10. A matheuristic for the liner shipping network design problem

    DEFF Research Database (Denmark)

    Brouer, Berit Dangaard; Desaulniers, Guy; Pisinger, David

    2014-01-01

    We present an integer programming based heuristic, a matheuristic, for the liner shipping network design problem. This problem consists of finding a set of container shipping routes defining a capacitated network for cargo transport. The objective is to maximize the revenue of cargo transport...

  11. Communications network design and costing model users manual

    Science.gov (United States)

    Logan, K. P.; Somes, S. S.; Clark, C. A.

    1983-01-01

    The information and procedures needed to exercise the communications network design and costing model for performing network analysis are presented. Specific procedures are included for executing the model on the NASA Lewis Research Center IBM 3033 computer. The concepts, functions, and data bases relating to the model are described. Model parameters and their format specifications for running the model are detailed.

  12. Communications network design and costing model programmers manual

    Science.gov (United States)

    Logan, K. P.; Somes, S. S.; Clark, C. A.

    1983-01-01

    Otpimization algorithms and techniques used in the communications network design and costing model for least cost route and least cost network problems are examined from the programmer's point of view. All system program modules, the data structures within the model, and the files which make up the data base are described.

  13. Reliability in urban public transport network assessment and design

    NARCIS (Netherlands)

    Tahmasseby, S.

    2009-01-01

    This research focuses on the influence of reliability of urban public transport services on network evaluation and network design. Public transport services suffer from all kind of disturbances, varying demand patterns, weather conditions, incidents, road works, et cetera. Current practice uses all

  14. NetworkedDesign : Next generation infrastructure for computational design

    NARCIS (Netherlands)

    Coenders, J.L.

    2011-01-01

    During the design and engineering process of buildings and structures an enormous amount of data and information is produced. Logic, knowledge and experience is employed during this process by the designers and engineers to finally come to the design result. Because this information can not be fully

  15. WDM Systems and Networks Modeling, Simulation, Design and Engineering

    CERN Document Server

    Ellinas, Georgios; Roudas, Ioannis

    2012-01-01

    WDM Systems and Networks: Modeling, Simulation, Design and Engineering provides readers with the basic skills, concepts, and design techniques used to begin design and engineering of optical communication systems and networks at various layers. The latest semi-analytical system simulation techniques are applied to optical WDM systems and networks, and a review of the various current areas of optical communications is presented. Simulation is mixed with experimental verification and engineering to present the industry as well as state-of-the-art research. This contributed volume is divided into three parts, accommodating different readers interested in various types of networks and applications. The first part of the book presents modeling approaches and simulation tools mainly for the physical layer including transmission effects, devices, subsystems, and systems), whereas the second part features more engineering/design issues for various types of optical systems including ULH, access, and in-building system...

  16. Architectural Design for the Global Legal Information Network

    Science.gov (United States)

    Kalpakis, Konstantinos

    1999-01-01

    In this report, we provide a summary of our activities regarding the goals, requirements analysis, design, and prototype implementation for the Global Legal Information Network, a joint effort between the Law Library of Congress and NASA.

  17. Designing Resource-Bounded Reasoners using Bayesian Networks

    Data.gov (United States)

    National Aeronautics and Space Administration — In this work we are concerned with the conceptual design of large-scale diagnostic and health management systems that use Bayesian networks. While they are...

  18. A Network Design Approach to Countering Terrorism

    Science.gov (United States)

    2015-09-01

    of the eyes ; that is shapes, colors and animations with the language of the mind; such as the concepts of relationships, processes, models and...Religion became a way to regain dignity, find a spiritual call, and promote self - esteem (Bramadat & Dawson, 2014). Terrorism researchers have often...result was a flexible, self -forming enemy network with an impressive capability to grow and sustain losses (McChrystal, 2011): In bitter, bloody fights

  19. Spacecraft Neural Network Control System Design using FPGA

    OpenAIRE

    Hanaa T. El-Madany; Faten H. Fahmy; Ninet M. A. El-Rahman; Hassen T. Dorrah

    2011-01-01

    Designing and implementing intelligent systems has become a crucial factor for the innovation and development of better products of space technologies. A neural network is a parallel system, capable of resolving paradigms that linear computing cannot. Field programmable gate array (FPGA) is a digital device that owns reprogrammable properties and robust flexibility. For the neural network based instrument prototype in real time application, conventional specific VLSI neural chip design suffer...

  20. GSM Network Employment on a Man-Portable UAS

    Science.gov (United States)

    2012-09-01

    the Zapata telephony project by Jim Dixon where he conceived that a general purpose CPU would handle DSP functions normally required in telephone...https://www.ettus.com/content/files/Ettus_E100– 110_DS_FINAL_1.27.12. pdf 89 Ettus Research LLC. (2012, August 2). E1xx images. retrieved from

  1. Gsm Networks: A Review Of Security Threats And Mitigation Measures

    African Journals Online (AJOL)

    If you would like more information about how to print, save, and work with PDFs, Highwire Press provides a helpful Frequently Asked Questions about PDFs. Alternatively, you can download the PDF file directly to your computer, from where it can be opened using a PDF reader. To download the PDF, click the Download link ...

  2. performance performance analysis of gsm networks in minna ...

    African Journals Online (AJOL)

    eobe

    azimuth adjustment and retune of broadcast control channel (BCCH) frequencies une of broadcast ... through the second generation (2G) of digital system ..... many phenomena that affect the listener's perception of speech quality. That is why other metrics are defined to take care of factors that RX-Qual does not consider ...

  3. Diseño e implementación de un sistema domótico remoto vía GSM para el Hotel San Miguel

    OpenAIRE

    Oña Chipuxi, Rosa Yadira

    2015-01-01

    At present there is a constant technological advancement, security has seen the need to innovate alarm systems that exist in the market, So that is necessary the creation of a general system in which developed the construction of a home automation system using the GSM technology. The goal of this project is the analysis, design and implementation of a prototype home automation remote via GSM for Hotel San Miguel, able to activate the alarm when a sensor to send a signal informing the possi...

  4. Broadcast design in cognitive radio ad hoc networks

    CERN Document Server

    Song, Yi

    2014-01-01

    This SpringerBrief investigates the special challenges of broadcast design in cognitive radio (CR) ad hoc networks. It introduces two broadcast protocols in CR ad hoc networks: a quality-of-service based broadcast protocol under blind information and a fully-distributed broadcast protocol with collision avoidance. A novel unified analytical model is also presented to analyze the performance of the broadcast protocols. This is the first book dedicated to the unique broadcast design challenges in CR ad hoc networks. The authors also discuss the recent research on the performance analysis of broa

  5. Optimal design of an IP/MPLS over DWDM network

    Directory of Open Access Journals (Sweden)

    Eduardo Canale

    2014-04-01

    Full Text Available Different approaches for deploying resilient optical networks of low cost constitute a traditional group of NP-Hard problems that have been widely studied. Most of them are based on the construction of low cost networks that fulfill connectivity constraints. However, recent trends to virtualize optical networks over the legacy fiber infrastructure, modified the nature of network design problems and turned inappropriate many of these models and algorithms. In this paper we study a design problem arising from the deployment of an IP/MPLS network over an existing DWDM infrastructure. Besides cost and resiliency, this problem integrates traffic and capacity constraints. We present: an integer programming formulation for the problem, theoretical results, and describe how several metaheuristics were applied in order to find good quality solutions, for a real application case of a telecommunications company.

  6. The architectural design of networks of protein domain architectures.

    Science.gov (United States)

    Hsu, Chia-Hsin; Chen, Chien-Kuo; Hwang, Ming-Jing

    2013-08-23

    Protein domain architectures (PDAs), in which single domains are linked to form multiple-domain proteins, are a major molecular form used by evolution for the diversification of protein functions. However, the design principles of PDAs remain largely uninvestigated. In this study, we constructed networks to connect domain architectures that had grown out from the same single domain for every single domain in the Pfam-A database and found that there are three main distinctive types of these networks, which suggests that evolution can exploit PDAs in three different ways. Further analysis showed that these three different types of PDA networks are each adopted by different types of protein domains, although many networks exhibit the characteristics of more than one of the three types. Our results shed light on nature's blueprint for protein architecture and provide a framework for understanding architectural design from a network perspective.

  7. State Observer Design for Delayed Genetic Regulatory Networks

    Directory of Open Access Journals (Sweden)

    Li-Ping Tian

    2014-01-01

    Full Text Available Genetic regulatory networks are dynamic systems which describe the interactions among gene products (mRNAs and proteins. The internal states of a genetic regulatory network consist of the concentrations of mRNA and proteins involved in it, which are very helpful in understanding its dynamic behaviors. However, because of some limitations such as experiment techniques, not all internal states of genetic regulatory network can be effectively measured. Therefore it becomes an important issue to estimate the unmeasured states via the available measurements. In this study, we design a state observer to estimate the states of genetic regulatory networks with time delays from available measurements. Furthermore, based on linear matrix inequality (LMI approach, a criterion is established to guarantee that the dynamic of estimation error is globally asymptotically stable. A gene repressillatory network is employed to illustrate the effectiveness of our design approach.

  8. Resilience-based optimal design of water distribution network

    Science.gov (United States)

    Suribabu, C. R.

    2017-11-01

    Optimal design of water distribution network is generally aimed to minimize the capital cost of the investments on tanks, pipes, pumps, and other appurtenances. Minimizing the cost of pipes is usually considered as a prime objective as its proportion in capital cost of the water distribution system project is very high. However, minimizing the capital cost of the pipeline alone may result in economical network configuration, but it may not be a promising solution in terms of resilience point of view. Resilience of the water distribution network has been considered as one of the popular surrogate measures to address ability of network to withstand failure scenarios. To improve the resiliency of the network, the pipe network optimization can be performed with two objectives, namely minimizing the capital cost as first objective and maximizing resilience measure of the configuration as secondary objective. In the present work, these two objectives are combined as single objective and optimization problem is solved by differential evolution technique. The paper illustrates the procedure for normalizing the objective functions having distinct metrics. Two of the existing resilience indices and power efficiency are considered for optimal design of water distribution network. The proposed normalized objective function is found to be efficient under weighted method of handling multi-objective water distribution design problem. The numerical results of the design indicate the importance of sizing pipe telescopically along shortest path of flow to have enhanced resiliency indices.

  9. The Military Theater Distribution Network Design Problem

    Science.gov (United States)

    2015-03-26

    manufacturing, power distribution, resource management, financial planning, and many others. The study of network flow models in effect addresses three questions...vary in levels of economic, social, and political stability. As a nation formed by colonial powers in the 18th century, Nigerias borders are at times...Absolute : •False ) ’ • •• ’ Cell~ (l3 + 1 , 7 ) . A<:Ldre~~ (Re!erenceS~yle : •xlAl , RowAhs o l u t e: • P"aln , Col wtnAbs olu t e : • r a lae

  10. Self-repair networks a mechanism design

    CERN Document Server

    Ishida, Yoshiteru

    2015-01-01

    This book describes the struggle to introduce a mechanism that enables next-generation information systems to maintain themselves. Our generation observed the birth and growth of information systems, and the Internet in particular. Surprisingly information systems are quite different from conventional (energy, material-intensive) artificial systems, and rather resemble biological systems (information-intensive systems). Many artificial systems are designed based on (Newtonian) physics assuming that every element obeys simple and static rules; however, the experience of the Internet suggests a different way of designing where growth cannot be controlled but self-organized with autonomous and selfish agents. This book suggests using game theory, a mechanism design in particular, for designing next-generation information systems which will be self-organized by collective acts with autonomous components. The challenge of mapping a probability to time appears repeatedly in many forms throughout this book. The book...

  11. K-12 Local Network (LAN) Design Guide

    National Research Council Canada - National Science Library

    Horton, Cody

    1998-01-01

    ...) educators preparing to design and implement LANs in K-12 schools and libraries. Data was collected during the implementation of LANs in K-12 schools of the Monterey Peninsula Uniform School District (MPUSD...

  12. Analysis and Comparison of Typical Models within Distribution Network Design

    DEFF Research Database (Denmark)

    Jørgensen, Hans Jacob; Larsen, Allan; Madsen, Oli B.G.

    This paper investigates the characteristics of typical optimisation models within Distribution Network Design. During the paper fourteen models known from the literature will be thoroughly analysed. Through this analysis a schematic approach to categorisation of distribution network design models...... for educational purposes. Furthermore, the paper can be seen as a practical introduction to network design modelling as well as a being an art manual or recipe when constructing such a model....... are covered in the categorisation include fixed vs. general networks, specialised vs. general nodes, linear vs. nonlinear costs, single vs. multi commodity, uncapacitated vs. capacitated activities, single vs. multi modal and static vs. dynamic. The models examined address both strategic and tactical planning...

  13. DESIGN AND PROTOTYPE OF RESOURCE NETWORK INTERFACES FOR NETWORK ON CHIP

    OpenAIRE

    Mahmood, Adnan; Mohammed, Zaheer Ahmed

    2009-01-01

    Network on Chip (NoC) has emerged as a competitive and efficient communication infrastructure for the core based design of System on Chip. Resource (core), router and interface between router and core are the three main parts of a NoC. Each core communicates with the network through the interface, also called Resource Network Interface (RNI). One approach to speed up the design at NoC based systems is to develop standardized RNI. Design of RNI depends to some extent on the type of routing tec...

  14. A large-scale measurement of electromagnetic fields near GSM base stations in Guangxi, China for risk communication

    International Nuclear Information System (INIS)

    Wu, T.; Shao, Q.; Yang, L.; Qi, D.; Lin, J.; Lin, X.; Yu, Z.

    2013-01-01

    Radiofrequency (RF) electromagnetic field (EMF) exposure from wireless telecommunication base station antennae can lead to debates, conflicts or litigations among the adjacent residents if inappropriately managed. This paper presents a measurement campaign for the GSM band EMF exposure in the vicinity of 827 base station sites (totally 6207 measurement points) in Guangxi, China. Measurement specifications are designed for risk communication with the residents who previously complained of over-exposure. The EMF power densities with the global positioning system coordinate at each measured point were recorded. Compliance with the International Commission on Non-Ionizing Radiation Protection guidelines and Chinese environmental EMF safety standards was studied. The results show that the GSM band EMF level near the base stations is very low. The measurement results and the EMF risk communication procedures positively influence public perception of the RF EMF exposure from the base stations and promote the exchange of EMF exposure-related knowledge. (authors)

  15. Design of atomic energy information network system

    International Nuclear Information System (INIS)

    Kim, Y. T.; Lee, E. J.; Han, K. W.; Lee, H. C.; Chang, J. H.

    2004-01-01

    As the 21 st century is expected to induce a Knowledge based society, responding to this kind of change on our own initiative could be achieved by establishing networks among atomic energy agencies with the Atomic Energy Portal Site in a pivotal role. Thus, enabling the knowledge information from each agency to be easily shared and utilized. Furthermore, it can contribute to further researches by providing accumulated knowledge in the atomic energy, such as research output and past achievements, and by avoiding the repetition of researches on the same subjects. It could also provide remote educational data to researchers and industrial experts in atomic energy, as well as atomic energy information for general public consistently, so that we can promote our confidence in atomic energy

  16. Design and optimizing factors of PACS network architecture

    International Nuclear Information System (INIS)

    Tao Yonghao; Miao Jingtao

    2001-01-01

    Objective: Exploring the design and optimizing factors of picture archiving and communication system (PACS) network architecture. Methods: Based on the PACS of shanghai first hospital to performed the measurements and tests on the requirements of network bandwidth and transmitting rate for different PACS functions and procedures respectively in static and dynamic network traffic situation, utilizing the network monitoring tools which built-in workstations and provided by Windows NT. Results: No obvious difference between switch equipment and HUB when measurements and tests implemented in static situation except route which slow down the rate markedly. In dynamic environment Switch is able to provide higher bandwidth utilizing than HUB and local system scope communication achieved faster transmitting rate than global system. Conclusion: The primary optimizing factors of PACS network architecture design include concise network topology and disassemble tremendous global traffic to multiple distributed local scope network communication to reduce the traffic of network backbone. The most important issue is guarantee essential bandwidth for diagnosis procedure of medical imaging

  17. Robust Optimization of Fourth Party Logistics Network Design under Disruptions

    Directory of Open Access Journals (Sweden)

    Jia Li

    2015-01-01

    Full Text Available The Fourth Party Logistics (4PL network faces disruptions of various sorts under the dynamic and complex environment. In order to explore the robustness of the network, the 4PL network design with consideration of random disruptions is studied. The purpose of the research is to construct a 4PL network that can provide satisfactory service to customers at a lower cost when disruptions strike. Based on the definition of β-robustness, a robust optimization model of 4PL network design under disruptions is established. Based on the NP-hard characteristic of the problem, the artificial fish swarm algorithm (AFSA and the genetic algorithm (GA are developed. The effectiveness of the algorithms is tested and compared by simulation examples. By comparing the optimal solutions of the 4PL network for different robustness level, it is indicated that the robust optimization model can evade the market risks effectively and save the cost in the maximum limit when it is applied to 4PL network design.

  18. Designing New Supply Chain Networks: Tomato and Mango Case Studies

    NARCIS (Netherlands)

    Vorst, van der J.G.A.J.; Schouten, R.E.; Luning, P.A.; Kooten, van O.

    2014-01-01

    Consumers expect product availability as well as product quality and safety in retail outlets. When designing or re-designing fruit and vegetables supply chain networks one has to take these demands into consideration next to traditional efficiency and responsiveness requirements. In food science

  19. Design of a Networked Learning Master Environment for Professionals

    DEFF Research Database (Denmark)

    Dirckinck-Holmfeld, Lone

    2010-01-01

    The paper is presenting the overall learning design of MIL (Master in ICT and Learning). The learning design is integrating a number of principles: 1. Principles of problem and project based learning 2. Networked learning / learning in communities of practice. The paper will discuss how these pri...

  20. RFID Based Security Access Control System with GSM Technology

    OpenAIRE

    Peter Adole; Joseph M. Môm; Gabriel A. Igwue

    2016-01-01

    The security challenges being encountered in many places today require electronic means of controlling access to secured premises in addition to the available security personnel. Various technologies were used in different forms to solve these challenges. The Radio Frequency Identification (RFID) Based Access Control Security system with GSM technology presented in this work helps to prevent unauthorized access to controlled environments (secured premises). This is achieved mainly...

  1. Virtual private network design : a proof of the tree routing conjecture on ring networks

    NARCIS (Netherlands)

    Hurkens, C.A.J.; Keijsper, J.C.M.; Stougie, L.

    2007-01-01

    A basic question in virtual private network (VPN) design is if the symmetric version of the problem always has an optimal solution which is a tree network. An affirmative answer would imply that the symmetric VPN problem is solvable in polynomial time. We give an affirmative answer in case the

  2. Virtual private network design: a proof of the tree routing conjecture on ring networks

    NARCIS (Netherlands)

    C.A.J. Hurkens (Cor); J.C.M. Keijsper; L. Stougie (Leen)

    2005-01-01

    htmlabstractA basic question in Virtual Private Network (VPN) design is if the symmetric version of the problem always has an optimal solution which is a tree network. An affirmative answer would imply that the symmetric VPN problem is solvable in polynomial time. We give an affirmative answer in

  3. Interoperability in the networked design infrastructure

    NARCIS (Netherlands)

    Coenders, J.L.

    2012-01-01

    Interoperability, the ability of different software applications to communicate with each other, is one of the biggest challenges for efficient and effective use of advanced software technology in structural design and engineering. In practice, the problem of interoperability exists very much for

  4. A Theoretical Design for Learning Model Addressing the Networked Society

    DEFF Research Database (Denmark)

    Nielsen, Janni; Levinsen, Karin Tweddell; Sørensen, Birgitte Holm

    2010-01-01

    The transition from the industrial to the networked society produces contradictions that challenges the educational system and force it to adapt to new conditions. In a Danish virtual Master in Information and Communication Technologies and Learning (MIL) these contradictions appear as a field....... The context for the experiment is MIL's course on Interaction Design. The orchestration is operationalized as a 4-hour script that builds on classic role-play designed as an open ended explorative task. The script of the teams' tasks is designed to facilitate the teams' ongoing negotiation and structuring...... which enables students to develop Networked Society competencies and maintain progression in the learning process also during the online periods. Additionally we suggest that our model contributes to the innovation of a networked society's design for learning....

  5. Network Mergers and Migrations Junos? Design and Implementation Junos Design and Implementation

    CERN Document Server

    Herrero, Gonzalo Gomez

    2010-01-01

    This book provides a complete reference to network mergers and migrations using the Junos operating system. Network Mergers and Migrations provides readers with a comprehensive guide for network migration activities by detailing a variety of internetworking case studies. Both enterprise and service provider scenarios are examined based on the experience and expertise of two senior Juniper Networks engineers. From MPLS Layer 3 VPN migration approaches to comprehensive network protocol consolidation and integration, each case study covers planning, design and implementation, as well as discussin

  6. Ensemble Entropy for Monitoring Network Design

    Directory of Open Access Journals (Sweden)

    Leonardo Alfonso

    2014-03-01

    Full Text Available Information-theory provides, among others, conceptual methods to quantify the amount of information contained in single random variables and methods to quantify the amount of information contained and shared among two or more variables. Although these concepts have been successfully applied in hydrology and other fields, the evaluation of these quantities is sensitive to different assumptions in the estimation of probabilities. An example is the histogram bin size used to estimate probabilities to calculate Information Theory quantities via frequency methods. The present research aims at introducing a method to take into consideration the uncertainty coming from these parameters in the evaluation of the North Sea’s water level network. The main idea is that the entropy of a random variable can be represented as a probability distribution of possible values, instead of entropy being a deterministic value. The method consists of solving multiple scenarios of Multi-Objective Optimization Problem in which information content is maximized and redundancy is minimized. Results include probabilistic analysis of the chosen parameters on the resulting family of Pareto fronts, providing additional criteria on the selection of the final set of monitoring points.

  7. Wi-Fi and GSM Based Motion Sensor for Home Security System Apllication

    Science.gov (United States)

    Huzaimy Jusoh, Mohamad; Jamali, Muhammad Firdaus Bin; Zainal Abidin, Ahmad Faizal bin; Asari Sulaiman, Ahmad; Fahmi Hussin, Mohamad

    2015-11-01

    The Wi-Fi and GSM based home security system is a system designed to reduce the high rates of crimes in most personal housing. The overall project consists of three major parts; the input part that consists of sensors, the software part that operates the entire hardware structure, and the output part, which consists of camera, alarm system, and micro secure digital (SD) data storage card. It is based on the principle of infrared radiation generated by a human body heat which trigger the passive infrared (PIR) sensor. The microcontroller processes the received signal, then trigger the buzzer alarm, camera and alerts the home owner through an SMS. Once triggered, the camera will capture the image of the intruder and the image will be saved in SD card. As alert to the user (away), the Global System for Mobile Communication (GSM) will send the Short Message Service (SMS) from the device to the user's mobile phone. The image will be sent to Dropbox data cloud storage via Wi-Fi for further clarification. The prototype was successfully developed, tested and has been installed at residential area in Taman Cahaya Alam, Section U12, Shah Alam, Malaysia.

  8. Food Web Designer: a flexible tool to visualize interaction networks.

    Science.gov (United States)

    Sint, Daniela; Traugott, Michael

    Species are embedded in complex networks of ecological interactions and assessing these networks provides a powerful approach to understand what the consequences of these interactions are for ecosystem functioning and services. This is mandatory to develop and evaluate strategies for the management and control of pests. Graphical representations of networks can help recognize patterns that might be overlooked otherwise. However, there is a lack of software which allows visualizing these complex interaction networks. Food Web Designer is a stand-alone, highly flexible and user friendly software tool to quantitatively visualize trophic and other types of bipartite and tripartite interaction networks. It is offered free of charge for use on Microsoft Windows platforms. Food Web Designer is easy to use without the need to learn a specific syntax due to its graphical user interface. Up to three (trophic) levels can be connected using links cascading from or pointing towards the taxa within each level to illustrate top-down and bottom-up connections. Link width/strength and abundance of taxa can be quantified, allowing generating fully quantitative networks. Network datasets can be imported, saved for later adjustment and the interaction webs can be exported as pictures for graphical display in different file formats. We show how Food Web Designer can be used to draw predator-prey and host-parasitoid food webs, demonstrating that this software is a simple and straightforward tool to graphically display interaction networks for assessing pest control or any other type of interaction in both managed and natural ecosystems from an ecological network perspective.

  9. How Many Smart Meters can be Deployed in a GSM cell?

    DEFF Research Database (Denmark)

    Madueño, Germán Corrales; Stefanovic, Cedomir; Popovski, Petar

    2013-01-01

    The need to deploy large number of wireless devices, such as electricity or water meters, is becoming a key challenge for any utility. Furthermore, such a deployment should be functional for more than a decade. Many cellular operators consider LTE to be the single long term solution for wide area...... the network stability. We show that a single GSM cell can support simultaneous low-data rate connections (e. g. to smart meters) in the order of 104 devices.......The need to deploy large number of wireless devices, such as electricity or water meters, is becoming a key challenge for any utility. Furthermore, such a deployment should be functional for more than a decade. Many cellular operators consider LTE to be the single long term solution for wide area...

  10. Toward Designing a Quantum Key Distribution Network Simulation Model

    OpenAIRE

    Miralem Mehic; Peppino Fazio; Miroslav Voznak; Erik Chromy

    2016-01-01

    As research in quantum key distribution network technologies grows larger and more complex, the need for highly accurate and scalable simulation technologies becomes important to assess the practical feasibility and foresee difficulties in the practical implementation of theoretical achievements. In this paper, we described the design of simplified simulation environment of the quantum key distribution network with multiple links and nodes. In such simulation environment, we analyzed several ...

  11. Transceiver design for wireless energy harvesting cooperative networks

    OpenAIRE

    Hu, Shiyang

    2016-01-01

    In this thesis, the RF energy harvesting technique is studied in the cooperative wireless network, and different optimization studies are investigated. First, an energy-efficient optimization is considered in the cooperative system with the time switching relaying and power splitting relaying protocols. Then, a security issue in the cooperative network with energy harvesting is proposed, in which the optimization problem is designed to maximize the secrecy rate. We also consider the applicati...

  12. High speed fiber optics local area networks: Design and implementation

    Science.gov (United States)

    Tobagi, Fouad A.

    1988-01-01

    The design of high speed local area networks (HSLAN) for communication among distributed devices requires solving problems in three areas: (1) the network medium and its topology; (2) the medium access control; and (3) the network interface. Considerable progress has been made in all areas. Accomplishments are divided into two groups according to their theoretical or experimental nature. A brief summary is given in Section 2, including references to papers which appeared in the literature, as well as to Ph.D. dissertations and technical reports published at Stanford University.

  13. Optimal Design of Gravitational Sewer Networks with General Cellular Automata

    Directory of Open Access Journals (Sweden)

    Mohammad Hadi Afshar

    2014-05-01

    Full Text Available In this paper, a Cellular Automata method is applied for the optimal design of sewer networks. The solution of sewer network optimization problems requires the determination of pipe diameters and average pipe cover depths, minimizing the total cost of the sewer network subject to operational constraints. In this paper, the network nodes and upstream and downstream pipe cover depths are considered as CA cells and cell states, respectively, and the links around each cell are taken into account as neighborhood. The proposed method is a general and flexible method for the optimization of sewer networks as it can be used to optimally design both gravity and pumped network due to the use of pipe nodal cover depths as the decision variables. The proposed method is tested against two  gravitational sewer networks and the  comparison of results with other methods such as  Genetic algorithm, Cellular Automata, Ant Colony Optimization Algorithm and Particle Swarm Optimization show the efficiency and effectiveness of the proposed method.

  14. Strategic Ozone Sounding Networks: Review of Design and Accomplishments

    Science.gov (United States)

    Thompson, Anne M.; Oltmans, Samuel J.; Tarasick, David W.; von der Gathen, Peter; Smit, Herman G. J.; Witte, Jacquelyn C.

    2011-01-01

    Ozone soundings are used to integrate models, satellite, aircraft and ground-based measurements for better interpretation of ozone variability, including atmospheric losses (predominantly in the stratosphere) and pollution (troposphere). A well-designed network of ozonesonde stations gives information with high vertical and horizontal resolution on a number of dynamical and chemical processes, allowing us to answer questions not possible with aircraft campaigns or current satellite technology. Strategic ozonesonde networks are discussed for high, mid- and low latitude studies. The Match sounding network was designed specifically to follow ozone depletion within the polar vortex; the standard sites are at middle to high northern hemisphere latitudes and typically operate from December through mid-March. Three mid-latitude strategic networks (the IONS series) operated over North America in July-August 2004, March-May and August 2006, and April and June-July-2008. These were designed to address questions about tropospheric ozone budgets and sources, including stratosphere-troposphere transport, and to validate satellite instruments and models. A global network focusing on processes in the equatorial zone, SHADOZ (Southern Hemisphere Additional Ozonesondes), has operated since 1998 in partnership with NOAA, NASA and the Meteorological Services of host countries. Examples of important findings from these networks are described,

  15. Protocol design and analysis for cooperative wireless networks

    CERN Document Server

    Song, Wei; Jin, A-Long

    2017-01-01

    This book focuses on the design and analysis of protocols for cooperative wireless networks, especially at the medium access control (MAC) layer and for crosslayer design between the MAC layer and the physical layer. It highlights two main points that are often neglected in other books: energy-efficiency and spatial random distribution of wireless devices. Effective methods in stochastic geometry for the design and analysis of wireless networks are also explored. After providing a comprehensive review of existing studies in the literature, the authors point out the challenges that are worth further investigation. Then, they introduce several novel solutions for cooperative wireless network protocols that reduce energy consumption and address spatial random distribution of wireless nodes. For each solution, the book offers a clear system model and problem formulation, details of the proposed cooperative schemes, comprehensive performance analysis, and extensive numerical and simulation results that validate th...

  16. Optimum Water Quality Monitoring Network Design for Bidirectional River Systems

    Directory of Open Access Journals (Sweden)

    Xiaohui Zhu

    2018-01-01

    Full Text Available Affected by regular tides, bidirectional water flows play a crucial role in surface river systems. Using optimization theory to design a water quality monitoring network can reduce the redundant monitoring nodes as well as save the costs for building and running a monitoring network. A novel algorithm is proposed to design an optimum water quality monitoring network for tidal rivers with bidirectional water flows. Two optimization objectives of minimum pollution detection time and maximum pollution detection probability are used in our optimization algorithm. We modify the Multi-Objective Particle Swarm Optimization (MOPSO algorithm and develop new fitness functions to calculate pollution detection time and pollution detection probability in a discrete manner. In addition, the Storm Water Management Model (SWMM is used to simulate hydraulic characteristics and pollution events based on a hypothetical river system studied in the literature. Experimental results show that our algorithm can obtain a better Pareto frontier. The influence of bidirectional water flows to the network design is also identified, which has not been studied in the literature. Besides that, we also find that the probability of bidirectional water flows has no effect on the optimum monitoring network design but slightly changes the mean pollution detection time.

  17. Optimization of emergy sustainability index for biodiesel supply network design

    International Nuclear Information System (INIS)

    Ren, Jingzheng; Tan, Shiyu; Yang, Le; Goodsite, Michael Evan; Pang, Chengfang; Dong, Lichun

    2015-01-01

    Highlights: • A MINLP model for designing sustainable biodiesel supply network is developed. • Emergy sustainability index is used as the objective to be maximized. • Multiple alternatives in each stage of biodiesel supply network are considered. • Life cycle perspective is incorporated in the design of biodiesel supply network. - Abstract: Sustainability is an important and difficult consideration for the stakeholders/decision-makers when planning a biofuel supply network. In this paper, a Mixed-Integer Non-linear Programming (MINLP) model was developed with the aim to help the stakeholders/decision-maker to select the most sustainable design. In the proposed model, the emergy sustainability index of the whole biodiesel supply networks in a life cycle perspective is employed as the measure of the sustainability, and multiple feedstocks, multiple transport modes, multiple regions for biodiesel production and multiple distribution centers can be considered. After describing the process and mathematic framework of the model, an illustrative case was studied and demonstrated that the proposed methodology is feasible for finding the most sustainable design and planning of biodiesel supply chains

  18. Utilization of GSM Module (Sim 900 Based Arduino-Uno for Alarm System and Remote Automatic Door Locking

    Directory of Open Access Journals (Sweden)

    Fauzi Fauzi

    2018-01-01

    Full Text Available Sebuah sistem alarm dan pengunci pintu otomatis jarak jauh untuk keamanan rumah telah dibuat. Otomatisasi kunci pintu rumah ini beroperasi dengan menggunakan perintah yang dikirimkan oleh pemilik rumah melalui pesan singkat melalui handphone sehingga keamanan rumah akan tetap dapat dikendalikan meski dari jarak yang jauh. Penelitian ini bertujuan untuk membangun otomatisasi rumah pintar yang mampu melakukan dua hal yakni mengunci pintu dan menyalakan alarm dengan menggunakan mikrokontroler Arduino-uno dan modul GSM. Pengontrolan secara otomatis tersebut cukup kompleks dan memerlukan berbagai komponen yang terintegrasi dengan kemampuan pembacaan masukan, pemrosesan data dan pengontrolan keluaran secara bersamaan dan terprogram.  A remote door automatic alarm and door lock system for home security has been designed. This home door lock automation operates using commands sent by homeowners via short messages from handphone so that home security will remain controllable even from a long distance. This study aims to build smart home automation that can do two things: lock the door and turn on the alarm by using Arduino-uno microcontroller and GSM module. The automatic control is quite complex and requires a variety of integrated components with the ability to read input, data processing and control the output simultaneously and programmed.   Keywords: Arduino, GSM, Automatic Doors, SMS Rerefences Depari, G.S. (1985. Belajar Teori dan Keterampilan Elektronika. Bandung: Armico Daryanto, 2005. Pengetahuan Teknik Elektronika. Erlangga. Jakarta. Session, Kendall Webster, 2003. 1001 Rangkaian Elektronika. PT. Elek Media Komputindo Kelompok Gramedia, Jakarta. Sustrisno, 1986, Elektronika Teori dan penerapanya. Penerbit ITB, Bandung

  19. FTTH passive optical networks and fiber plant design

    Science.gov (United States)

    Shen, Steven; Rich, Bill

    2001-10-01

    With extraordinary increase of bandwidth requirement nowadays, service providers are compelled to push fiber deeper into the access networks in order to be able to offer the emerging services that customers are demanding. The economic aspects from the business side also put pressure on operators to deploy single network for multiple applications in order to maximize profitability. There are various technologies used today to increase the capacity of the access network. Fiber-To-The-Home (FTTH) utilizing ATM Passive Optical Networking (APON) has been developed for and field-tried in numerous networks all over the world. The advantages of APON solution lies in its future proof fiber based access technology (high bandwidth and long service life). Fiber and passive components used in the network are very reliable and low in the maintenance cost. The APON technology is standardized in ITU-T G.983, which is originated from Full Services Access Network (FSAN) initiatives. It supports multiple applications and provides powerful quality of service (QoS). In this paper, the requirements for APON FTTH network architecture, transport protocol and operation are examined in line with G.983 standards. The comparisons of APON to other existing high data rate access network solutions are then briefly discussed. Case studies of APON FTTH field trials are used as examples. These trials represented current status of APON FTTH development in US, on both network system elements and fiber plant components. A complete picture of APON FTTH network system and Outside Plant (OSP) design from CO to the residential homes is illustrated by these field trials. Discussions are given on topics related to APON FTTH system elements, such as OLT/ONT design, lifeline support, optical power budget and operation/fault management. Considerations regarding the design and deployment of OSP components focus on the configuration and construction of the fiber plant. Common issues related to field

  20. Design of an optimal snow observation network to estimate snowpack

    Science.gov (United States)

    Juan Collados Lara, Antonio; Pardo-Iguzquiza, Eulogio; Pulido-Velazquez, David

    2016-04-01

    Snow is an important water resource in many river basins that must be taken into account in hydrological modeling. Although the snow cover area may be nowadays estimated from satellite data, the snow pack thickness must be estimated from experimental data by using some interpolation procedure or hydrological models that approximates snow accumulation and fusion processes. The experimental data consist of hand probes and snow samples collected in a given number of locations that constitute the monitoring network. Assuming that there is an existing monitoring network, its optimization may imply the selection of an optimal network as a subset of the existing network (decrease of the existing network in the case that there are no funds for maintaining the full existing network) or to increase the existing network by one or more stations (optimal augmentation problem). In this work we propose a multicriterion approach for the optimal design of a snow network. These criteria include the estimation variance from a regression kriging approach for estimating thickness of the snowpack (using ground and satellite data), to minimize the total snow volume and accessibility criteria. We have also proposed a procedure to analyze the sensitivity of the results to the non-snow data deduced from the satellite information. We intent to minimize the uncertities in snowpack estimation. The methodology has been applied to estimation of the snow cover area and the design of the optimal snow observation network in Sierra Nevada mountain range in the Southern of Spain. Acknowledgments: This research has been partially supported by the GESINHIMPADAPT project (CGL2013-48424-C2-2-R) with Spanish MINECO funds. We would also like to thank ERHIN program and NASA DAAC for the data provided for this study.

  1. Dissipative rendering and neural network control system design

    Science.gov (United States)

    Gonzalez, Oscar R.

    1995-01-01

    Model-based control system designs are limited by the accuracy of the models of the plant, plant uncertainty, and exogenous signals. Although better models can be obtained with system identification, the models and control designs still have limitations. One approach to reduce the dependency on particular models is to design a set of compensators that will guarantee robust stability to a set of plants. Optimization over the compensator parameters can then be used to get the desired performance. Conservativeness of this approach can be reduced by integrating fundamental properties of the plant models. This is the approach of dissipative control design. Dissipative control designs are based on several variations of the Passivity Theorem, which have been proven for nonlinear/linear and continuous-time/discrete-time systems. These theorems depend not on a specific model of a plant, but on its general dissipative properties. Dissipative control design has found wide applicability in flexible space structures and robotic systems that can be configured to be dissipative. Currently, there is ongoing research to improve the performance of dissipative control designs. For aircraft systems that are not dissipative active control may be used to make them dissipative and then a dissipative control design technique can be used. It is also possible that rendering a system dissipative and dissipative control design may be combined into one step. Furthermore, the transformation of a non-dissipative system to dissipative can be done robustly. One sequential design procedure for finite dimensional linear time-invariant systems has been developed. For nonlinear plants that cannot be controlled adequately with a single linear controller, model-based techniques have additional problems. Nonlinear system identification is still a research topic. Lacking analytical models for model-based design, artificial neural network algorithms have recently received considerable attention. Using

  2. Full-Band GSM Fingerprints for Indoor Localization Using a Machine Learning Approach

    Directory of Open Access Journals (Sweden)

    Iness Ahriz

    2010-01-01

    Full Text Available Indoor handset localization in an urban apartment setting is studied using GSM trace mobile measurements. Nearest-neighbor, Support Vector Machine, Multilayer Perceptron, and Gaussian Process classifiers are compared. The linear Support Vector Machine provides mean room classification accuracy of almost 98% when all GSM carriers are used. To our knowledge, ours is the first study to use fingerprints containing all GSM carriers, as well as the first to suggest that GSM can be useful for localization of very high performance.

  3. A design methodology for evolutionary air transportation networks

    Science.gov (United States)

    Yang, Eunsuk

    The air transportation demand at large hubs in the U.S. is anticipated to double in the near future. Current runway construction plans at selected airports can relieve some capacity and delay problems, but many are doubtful that this solution is sufficient to accommodate the anticipated demand growth in the National Airspace System (NAS). With the worsening congestion problem, it is imperative to seek alternative solutions other than costly runway constructions. In this respect, many researchers and organizations have been building models and performing analyses of the NAS. However, the complexity and size of the problem results in an overwhelming task for transportation system modelers. This research seeks to compose an active design algorithm for an evolutionary airline network model so as to include network specific control properties. An airline network designer, referred to as a network architect, can use this tool to assess the possibilities of gaining more capacity by changing the network configuration. Since the Airline Deregulation Act of 1978, the airline service network has evolved into a distinct Hub-and-Spoke (H&S) network. Enplanement demand on the H&S network is the sum of Origin-Destination (O-D) demand and transfer demand. Even though the flight or enplanement demand is a function of O-D demand and passenger routings on the airline network, the distinction between enplanement and O-D demand is not often made. Instead, many demand forecast practices in current days are based on scale-ups from the enplanements, which include the demand to and from transferring network hubs. Based on this research, it was found that the current demand prediction practice can be improved by dissecting enplanements further into smaller pieces of information. As a result, enplanement demand is decomposed into intrinsic and variable parts. The proposed intrinsic demand model is based on the concept of 'true' O-D demand which includes the direction of each round trip

  4. Extending Resolution of Fault Slip With Geodetic Networks Through Optimal Network Design

    Science.gov (United States)

    Sathiakumar, Sharadha; Barbot, Sylvain Denis; Agram, Piyush

    2017-12-01

    Geodetic networks consisting of high precision and high rate Global Navigation Satellite Systems (GNSS) stations continuously monitor seismically active regions of the world. These networks measure surface displacements and the amount of geodetic strain accumulated in the region and give insight into the seismic potential. SuGar (Sumatra GPS Array) in Sumatra, GEONET (GNSS Earth Observation Network System) in Japan, and PBO (Plate Boundary Observatory) in California are some examples of established networks around the world that are constantly expanding with the addition of new stations to improve the quality of measurements. However, installing new stations to existing networks is tedious and expensive. Therefore, it is important to choose suitable locations for new stations to increase the precision obtained in measuring the geophysical parameters of interest. Here we describe a methodology to design optimal geodetic networks that augment the existing system and use it to investigate seismo-tectonics at convergent and transform boundaries considering land-based and seafloor geodesy. The proposed network design optimization would be pivotal to better understand seismic and tsunami hazards around the world. Land-based and seafloor networks can monitor fault slip around subduction zones with significant resolution, but transform faults are more challenging to monitor due to their near-vertical geometry.

  5. Design and Simulation Analysis for Integrated Vehicle Chassis-Network Control System Based on CAN Network

    Directory of Open Access Journals (Sweden)

    Wei Yu

    2016-01-01

    Full Text Available Due to the different functions of the system used in the vehicle chassis control, the hierarchical control strategy also leads to many kinds of the network topology structure. According to the hierarchical control principle, this research puts forward the integrated control strategy of the chassis based on supervision mechanism. The purpose is to consider how the integrated control architecture affects the control performance of the system after the intervention of CAN network. Based on the principle of hierarchical control and fuzzy control, a fuzzy controller is designed, which is used to monitor and coordinate the ESP, AFS, and ARS. And the IVC system is constructed with the upper supervisory controller and three subcontrol systems on the Simulink platform. The network topology structure of IVC is proposed, and the IVC communication matrix based on CAN network communication is designed. With the common sensors and the subcontrollers as the CAN network independent nodes, the network induced delay and packet loss rate on the system control performance are studied by simulation. The results show that the simulation method can be used for designing the communication network of the vehicle.

  6. Algorithm Design on Network Game of Chinese Chess

    Science.gov (United States)

    Xianmei, Fang

    This paper describes the current situation of domestic network game. Contact the present condition of the local network game currently, we inquired to face to a multithread tcp client and server, such as Chinese chess, according to the information, and study the contents and meanings. Combining the Java of basic knowledge, the article study the compiling procedure facing to the object according to the information in Java Swing usage, and the method of the network procedure. The article researched the method and processes of the network procedure carry on the use of Sprocket under the Java Swing. Understood the basic process of compiling procedure using Java and how to compile a network procedure. The most importance is how a pair of machines correspondence-C/S the service system-is carried out. From here, we put forward the data structure,the basic calculate way of the network game- Chinese chess, and how to design and realize the server and client of that procedure. The online games -- chess design can be divided into several modules as follows: server module, client module and the control module.

  7. Optimization of Close Range Photogrammetry Network Design Applying Fuzzy Computation

    Science.gov (United States)

    Aminia, A. S.

    2017-09-01

    Measuring object 3D coordinates with optimum accuracy is one of the most important issues in close range photogrammetry. In this context, network design plays an important role in determination of optimum position of imaging stations. This is, however, not a trivial task due to various geometric and radiometric constraints affecting the quality of the measurement network. As a result, most camera stations in the network are defined on a try and error basis based on the user's experience and generic network concept. In this paper, we propose a post-processing task to investigate the quality of camera positions right after image capturing to achieve the best result. To do this, a new fuzzy reasoning approach is adopted, in which the constraints affecting the network design are all modeled. As a result, the position of all camera locations is defined based on fuzzy rules and inappropriate stations are determined. The experiments carried out show that after determination and elimination of the inappropriate images using the proposed fuzzy reasoning system, the accuracy of measurements is improved and enhanced about 17% for the latter network.

  8. Design of an ecological network for Piano di Navelli (Abruzzo); networks for LIFEE

    NARCIS (Netherlands)

    Grift, van der E.A.; Sluis, van der T.

    2003-01-01

    This report provides a design for an ecological network at Piano di Navelli, Abruzzo, Italy. The design is based on habitat and corridor requirements of five indicator species: green lizard (Lacerta bilineata), Italian crested newt (Triturus carnifex)water shrew (Neomys fodiens), hedgehog (Erinaceus

  9. A multiobjective optimization framework for multicontaminant industrial water network design.

    Science.gov (United States)

    Boix, Marianne; Montastruc, Ludovic; Pibouleau, Luc; Azzaro-Pantel, Catherine; Domenech, Serge

    2011-07-01

    The optimal design of multicontaminant industrial water networks according to several objectives is carried out in this paper. The general formulation of the water allocation problem (WAP) is given as a set of nonlinear equations with binary variables representing the presence of interconnections in the network. For optimization purposes, three antagonist objectives are considered: F(1), the freshwater flow-rate at the network entrance, F(2), the water flow-rate at inlet of regeneration units, and F(3), the number of interconnections in the network. The multiobjective problem is solved via a lexicographic strategy, where a mixed-integer nonlinear programming (MINLP) procedure is used at each step. The approach is illustrated by a numerical example taken from the literature involving five processes, one regeneration unit and three contaminants. The set of potential network solutions is provided in the form of a Pareto front. Finally, the strategy for choosing the best network solution among those given by Pareto fronts is presented. This Multiple Criteria Decision Making (MCDM) problem is tackled by means of two approaches: a classical TOPSIS analysis is first implemented and then an innovative strategy based on the global equivalent cost (GEC) in freshwater that turns out to be more efficient for choosing a good network according to a practical point of view. Copyright © 2011 Elsevier Ltd. All rights reserved.

  10. A matheuristic for the liner shipping network design problem

    DEFF Research Database (Denmark)

    Brouer, Berit Dangaard; Desaulniers, Guy; Pisinger, David

    the available fleet of container vessels. The cargo transports make extensive use of transshipments between routes and the number of transshipments of the cargo flow is decisive for network profitability. Computational results are reported for the benchmark suite LINER-LIB 2012 following the industry standard......We present a matheuristic, an integer programming based heuristic, for the liner shipping network design problem. This problem consists of finding a set of container shipping routes defining a capacitated network for cargo transport. The objective is to maximize the revenue of cargo transport......, while minimizing the cost of operating the network. Liner shipping companies publish a set of routes with a time schedule, and it is an industry standard to have a weekly departure at each port call on a route. A weekly frequency is achieved by deploying several vessels to a single route, respecting...

  11. Design and implementation considerations of a MSAT packet data network

    Science.gov (United States)

    Karam, Fouad G.; Hearn, Terry; Rohr, Doug; Guibord, Arthur F.

    1993-01-01

    The Mobile Data System, which is intended to provide for packet switched data services is currently under development. The system is based on a star network topology consisting of a centralized Data Hub (DH) serving a large number of mobile terminals. Through the Data Hub, end-to-end connections can be established between terrestrial users on public or private data networks and mobile users. The MDS network will be capable of offering a variety of services some of which are based on the standard X.25 network interface protocol, and others optimized for short messages and broadcast messages. A description of these services and the trade-offs in the DH design are presented.

  12. Optimal Design of Geodetic Network Using Genetic Algorithms

    Science.gov (United States)

    Vajedian, Sanaz; Bagheri, Hosein

    2010-05-01

    A geodetic network is a network which is measured exactly by techniques of terrestrial surveying based on measurement of angles and distances and can control stability of dams, towers and their around lands and can monitor deformation of surfaces. The main goals of an optimal geodetic network design process include finding proper location of control station (First order Design) as well as proper weight of observations (second order observation) in a way that satisfy all the criteria considered for quality of the network with itself is evaluated by the network's accuracy, reliability (internal and external), sensitivity and cost. The first-order design problem, can be dealt with as a numeric optimization problem. In this designing finding unknown coordinates of network stations is an important issue. For finding these unknown values, network geodetic observations that are angle and distance measurements must be entered in an adjustment method. In this regard, using inverse problem algorithms is needed. Inverse problem algorithms are methods to find optimal solutions for given problems and include classical and evolutionary computations. The classical approaches are analytical methods and are useful in finding the optimum solution of a continuous and differentiable function. Least squares (LS) method is one of the classical techniques that derive estimates for stochastic variables and their distribution parameters from observed samples. The evolutionary algorithms are adaptive procedures of optimization and search that find solutions to problems inspired by the mechanisms of natural evolution. These methods generate new points in the search space by applying operators to current points and statistically moving toward more optimal places in the search space. Genetic algorithm (GA) is an evolutionary algorithm considered in this paper. This algorithm starts with definition of initial population, and then the operators of selection, replication and variation are applied

  13. Efficient Minimax Design of Networks without Using Derivatives

    DEFF Research Database (Denmark)

    Madsen, Kaj; Nielsen, Niels Ole; Schjær-Jacobsen, Hans

    1975-01-01

    ., which makes the gradient computation by the adjoint network method or related methods rather complicated, and often numerical errors are introduced in the gradients. Consequently, the algorithm is found to be of particular relevance in optimum design of practical microwave networks. The relative...... advantages of the proposed algorithm are established by comparison with known gradient and nongradient algorithms based on optimization of cascaded transmission-line transformers. The relevance to microwave filter design is demonstrated by an example which represents an improvement of analytical filter...... design results. Finally, optimum broad-band design of a practical coaxial transferred-electron reflection-type amplilier is carried out by means of the proposed method. The results are supported by experimental verification....

  14. Analysis of Feeder Bus Network Design and Scheduling Problems

    Directory of Open Access Journals (Sweden)

    Mohammad Hadi Almasi

    2014-01-01

    Full Text Available A growing concern for public transit is its inability to shift passenger’s mode from private to public transport. In order to overcome this problem, a more developed feeder bus network and matched schedules will play important roles. The present paper aims to review some of the studies performed on Feeder Bus Network Design and Scheduling Problem (FNDSP based on three distinctive parts of the FNDSP setup, namely, problem description, problem characteristics, and solution approaches. The problems consist of different subproblems including data preparation, feeder bus network design, route generation, and feeder bus scheduling. Subsequently, descriptive analysis and classification of previous works are presented to highlight the main characteristics and solution methods. Finally, some of the issues and trends for future research are identified. This paper is targeted at dealing with the FNDSP to exhibit strategic and tactical goals and also contributes to the unification of the field which might be a useful complement to the few existing reviews.

  15. Analysis of feeder bus network design and scheduling problems.

    Science.gov (United States)

    Almasi, Mohammad Hadi; Mirzapour Mounes, Sina; Koting, Suhana; Karim, Mohamed Rehan

    2014-01-01

    A growing concern for public transit is its inability to shift passenger's mode from private to public transport. In order to overcome this problem, a more developed feeder bus network and matched schedules will play important roles. The present paper aims to review some of the studies performed on Feeder Bus Network Design and Scheduling Problem (FNDSP) based on three distinctive parts of the FNDSP setup, namely, problem description, problem characteristics, and solution approaches. The problems consist of different subproblems including data preparation, feeder bus network design, route generation, and feeder bus scheduling. Subsequently, descriptive analysis and classification of previous works are presented to highlight the main characteristics and solution methods. Finally, some of the issues and trends for future research are identified. This paper is targeted at dealing with the FNDSP to exhibit strategic and tactical goals and also contributes to the unification of the field which might be a useful complement to the few existing reviews.

  16. Optimization of emergy sustainability index for biodiesel supply network design

    DEFF Research Database (Denmark)

    Ren, Jingzheng; Tan, Shiyu; Yang, Le

    2015-01-01

    sustainable design. In the proposed model, the emergy sustainability index of the whole biodiesel supply networks in a life cycle perspective is employed as the measure of the sustainability, and multiple feedstocks, multiple transport modes, multiple regions for biodiesel production and multiple distribution...... centers can be considered. After describing the process and mathematic framework of the model, an illustrative case was studied and demonstrated that the proposed methodology is feasible for finding the most sustainable design and planning of biodiesel supply chains....

  17. Design of Fault Tolerant Network Interfaces for NoCs

    DEFF Research Database (Denmark)

    Fiorin, Leandro; Micconi, Laura; Sami, Mariagiovanna

    2011-01-01

    Networks-on-Chip (NoCs) appeared as a strategy to deal with the communication requirements of complex IP-based System-on-Chips. As the complexity of designs increases and the technology scales down into the deep-submicron domain, the probability of malfunctions and failures in the NoC components...

  18. Stochastic approaches for product recovery network design: a case study

    NARCIS (Netherlands)

    O.L. Listes (Ovidiu); R. Dekker (Rommert)

    2001-01-01

    textabstractIncreased uncertainty is one of the characteristics of product recovery networks. In particular the strategic design of their logistic infrastructure has to take uncertain information into account. In this paper we present stochastic programming based approaches by which a deterministic

  19. Radar signal design problem with neural network processing

    Indian Academy of Sciences (India)

    Unknown

    Abstract. Binary and ternary sequences with peaky autocorrelation, measured in terms of high discrimination and merit factor have been searched earlier, using optimization techniques. It is shown that the use of neural network processing of the return signal is much more advantageous. It opens up a new signal design ...

  20. design of government cloud network for a developing economy

    African Journals Online (AJOL)

    In Ondo State, some businesses, telecommunication agencies and government agencies are not utilizing Information Technology (IT) services to its maximum due to challenges faced by IT penetration in the state. This paper presents the design of a Government Cloud (G-Cloud) network for Ondo State Government which ...

  1. Multimedia as Rhizome: Design Issues in a Network Environment.

    Science.gov (United States)

    Burnett, Kathleen

    1992-01-01

    Defines the concepts of hypertext, hypermedia, multimedia, and multimedia networks. Using the rhizome as a metaphor for electronically mediated exchange, a theory of hypermedia design that incorporates principles of connection and heterogeneity, multiplicity, asignifying rupture, and cartography and decalomania is explored. (four references) (MES)

  2. The Design of a Large Scale Airline Network

    NARCIS (Netherlands)

    Carmona Benitez, R.B.

    2012-01-01

    Airlines invest a lot of money before opening new pax transportation services, for this reason, airlines have to analyze if their profits will overcome the amount of money they have to invest to open new services. The design and analysis of the feasibility of airlines networks can be done by using

  3. On design principles for self-organizing network functions

    NARCIS (Netherlands)

    Altman, Z.; Amirijoo, M.; Gunnarsson, F.; Hoffmann, H.; Kovács, I.Z.; Laselva, D.; Sas, B.; Spaey, K.; Tall, A.; Berg, H. van den; Zetterberg, K.

    2014-01-01

    With an increasing number of SON functions deployed in cellular radio networks, conflicts between the actions proposed by independently-designed and distributed SON functions may arise. The process of minimizing the occurrence, and the consequences, of such conflicts is referred to as SON

  4. Design issues and applications of wireless sensor networks ...

    African Journals Online (AJOL)

    ... using tiny wireless sensor motes known as “smart dusts”, which have been made possible by advances in micro-electromechanical systems (MEMS) technology, wireless communications and digital electronics. Design considerations for the hardware and the topology necessary to realize these networks were evaluated.

  5. An Optimal Design Model for New Water Distribution Networks in ...

    African Journals Online (AJOL)

    This paper is concerned with the problem of optimizing the distribution of water in Kigali City at a minimum cost. The mathematical formulation is a Linear Programming Problem (LPP) which involves the design of a new network of water distribution considering the cost in the form of unit price of pipes, the hydraulic gradient ...

  6. Network Design in Reverse Logistics: A Quantitative Model

    NARCIS (Netherlands)

    Krikke, H.R.; Kooij, E.J.; Schuur, Peter; Speranza, M. Grazia; Stähly, Paul

    1999-01-01

    The introduction of (extended) producer responsibility forces Original Equipment Manufacturers to solve entirely new managerial problems. One of the issues concerns the physical design of the reverse logistic network, which is a problem that fits into the class of facility-location problems. Since

  7. A structured approach to heat exchanger network retrofit design

    NARCIS (Netherlands)

    Van Reisen, J.L.B.

    2008-01-01

    Process plants have high energy consumption. Much energy can be saved by a proper design of the heat exchanger network, which contains the main heat transferring equipment of the plant. Existing plants can often be made more energy-efficient by a retrofit: the (physical) modification of the

  8. Liner shipping hub network design in a competitive environment

    DEFF Research Database (Denmark)

    Gelareh, Shahin; Nickel, Stefan; Pisinger, David

    2010-01-01

    market share—which depends on the service time and transportation cost—by locating a predefined number of hubs at candidate ports and designing its network. While general-purpose solvers do not solve instances of even small size, an accelerated Lagrangian method combined with a primal heuristic obtains...

  9. Liner Shipping Hub Network Design in a Competitive Environment

    DEFF Research Database (Denmark)

    Gelareh, Shahin; Nickel, Stefan; Pisinger, David

    — proportional to service time and transportation cost —by locating a predefined number of hubs at candidate ports and designing its network. While general-purpose solvers do not solve instances of even small size, an accelerated lagrangian method coupled with a primal heuristic obtains very good bounds. Our...

  10. Journal of EEA, Vol. 28, 2011 SUPPLY CHAIN NETWORK DESIGN ...

    African Journals Online (AJOL)

    Zede

    Keywords: Supply Chain Network Design,. Mathematical Model, Optimization. INTRODUCTION. Supply Chain (SC) is an integrated business model for logistics management. It covers the flow of goods from suppliers through manufacturing and distribution chains to the end customers. Effective. SC is viewed as the driver of ...

  11. The principle of complementarity in the design of reserve networks ...

    Indian Academy of Sciences (India)

    Unknown

    Explicit, quantitative procedures for identifying biodiversity priority areas are replacing the often ad hoc procedures used in the past to design networks of reserves to conserve biodiversity. This change facilitates more informed choices by policy makers, and thereby makes possible greater satisfaction of conservation goals ...

  12. Application of neural network to multi-dimensional design window search in reactor core design

    International Nuclear Information System (INIS)

    Kugo, Teruhiko; Nakagawa, Masayuki

    1999-01-01

    In the reactor core design, many parametric survey calculations should be carried out to decide an optimal set of basic design parameter values. They consume a large amount of computation time and labor in the conventional way. To support design work, we investigate a procedure to search efficiently a design window, which is defined as feasible design parameter ranges satisfying design criteria and requirements, in a multi-dimensional space composed of several basic design parameters. The present method is applied to the neutronics and thermal hydraulics fields. The principle of the present method is to construct the multilayer neural network to simulate quickly a response of an analysis code through a training process, and to reduce computation time using the neural network without parametric study using analysis codes. To verify the applicability of the present method to the neutronics and the thermal hydraulics design, we have applied it to high conversion water reactors and examined effects of the structure of the neural network and the number of teaching patterns on the accuracy of the design window estimated by the neural network. From the results of the applications, a guideline to apply the present method is proposed and the present method can predict an appropriate design window in a reasonable computation time by following the guideline. (author)

  13. Sustainable and Resilient Supply Chain Network Design under Disruption Risks

    Directory of Open Access Journals (Sweden)

    Sonia Irshad Mari

    2014-09-01

    Full Text Available Sustainable supply chain network design is a rich area for academic research that is still in its infancy and has potential to affect supply chain performance. Increasing regulations for carbon and waste management are forcing firms to consider their supply chains from ecological and social objectives, but in reality, however, facilities and the links connecting them are disrupted from time to time, due to poor weather, natural or manmade disasters or a combination of any other factors. Supply chain systems drop their sustainability objectives while coping with these unexpected disruptions. Hence, the new challenges for supply chain managers are to design an efficient and effective supply chain network that will be resilient enough to bounce back from any disruption and that also should have sufficient vigilance to offer same sustainability under a disruption state. This paper focuses on ecological sustainability, because an environmental focus in a supply chain system is more important and also links with other pillars of sustainability, as the products need to be produced, packed and transported in an ethical way, which should not harm social balance and the environment. Owing to importance of the considered issue, this paper attempts to introduce a network optimization model for a sustainable and resilient supply chain network by incorporating (1 sustainability via carbon emissions and embodied carbon footprints and (2 resilience by incorporating location-specific risks. The proposed goal programming (GP model optimizes the total cost, while considering the resilience and sustainability of the supply chain network.

  14. Designing optimal bioethanol networks with purification for integrated biorefineries

    International Nuclear Information System (INIS)

    Shenoy, Akshay U.; Shenoy, Uday V.

    2014-01-01

    Highlights: • An analytical method is devised for bioethanol network integration with purification. • Minimum fresh bioethanol flow and pinch are found by the Unified Targeting Algorithm. • Optimal bioethanol networks are then synthesized by the Nearest Neighbors Algorithm. • Continuous targets and networks are developed over the purifier inlet flowrate range. • Case study of a biorefinery producing bioethanol from wheat shows large savings. - Abstract: Bioethanol networks with purification for processing pathways in integrated biorefineries are targeted and designed in this work by an analytical approach not requiring graphical constructions. The approach is based on six fundamental equations involving eight variables: two balance equations for the stream flowrate and the bioethanol load over the total network system; one equation for the above-pinch bioethanol load being picked up by the minimum fresh resource and the purified stream; and three equations for the purification unit. A solution strategy is devised by specifying the two variables associated with the purifier inlet stream. Importantly, continuous targeting is then possible over the entire purifier inlet flowrate range on deriving elegant formulae for the remaining six variables. The Unified Targeting Algorithm (UTA) is utilized to establish the minimum fresh bioethanol resource flowrate and identify the pinch purity. The fresh bioethanol resource flowrate target is shown to decrease linearly with purifier inlet flowrate provided the pinch is held by the same point. The Nearest Neighbors Algorithm (NNA) is used to methodically synthesize optimal networks matching bioethanol demands and sources. A case study of a biorefinery producing bioethanol from wheat with arabinoxylan (AX) coproduction is presented. It illustrates the versatility of the approach in generating superior practical designs with up to nearly 94% savings for integrated bioethanol networks, both with and without process

  15. Neural network application to aircraft control system design

    Science.gov (United States)

    Troudet, Terry; Garg, Sanjay; Merrill, Walter C.

    1991-01-01

    The feasibility of using artificial neural network as control systems for modern, complex aerospace vehicles is investigated via an example aircraft control design study. The problem considered is that of designing a controller for an integrated airframe/propulsion longitudinal dynamics model of a modern fighter aircraft to provide independent control of pitch rate and airspeed responses to pilot command inputs. An explicit model following controller using H infinity control design techniques is first designed to gain insight into the control problem as well as to provide a baseline for evaluation of the neurocontroller. Using the model of the desired dynamics as a command generator, a multilayer feedforward neural network is trained to control the vehicle model within the physical limitations of the actuator dynamics. This is achieved by minimizing an objective function which is a weighted sum of tracking errors and control input commands and rates. To gain insight in the neurocontrol, linearized representations of the nonlinear neurocontroller are analyzed along a commanded trajectory. Linear robustness analysis tools are then applied to the linearized neurocontroller models and to the baseline H infinity based controller. Future areas of research identified to enhance the practical applicability of neural networks to flight control design.

  16. Wireless Sensor/Actuator Network Design for Mobile Control Applications

    Directory of Open Access Journals (Sweden)

    Youxian Sung

    2007-10-01

    Full Text Available Wireless sensor/actuator networks (WSANs are emerging as a new generationof sensor networks. Serving as the backbone of control applications, WSANs will enablean unprecedented degree of distributed and mobile control. However, the unreliability ofwireless communications and the real-time requirements of control applications raise greatchallenges for WSAN design. With emphasis on the reliability issue, this paper presents anapplication-level design methodology for WSANs in mobile control applications. Thesolution is generic in that it is independent of the underlying platforms, environment,control system models, and controller design. To capture the link quality characteristics interms of packet loss rate, experiments are conducted on a real WSAN system. From theexperimental observations, a simple yet efficient method is proposed to deal withunpredictable packet loss on actuator nodes. Trace-based simulations give promisingresults, which demonstrate the effectiveness of the proposed approach.

  17. UPStream: Automated hydraulic design of pressurized water distribution networks

    Science.gov (United States)

    Emmanouil, Stergios; Langousis, Andreas

    Hydraulic design of pressurized water distribution networks constitutes a time consuming process in engineering applications, requiring proper selection of pipe diameters so certain regulatory constrains are met. UPStream® is an open-source software, which combines EPANET's computational engine and a simple hydraulic gradient-based recursive approach for selection of pipe diameters, to automatically design pressurized water distribution networks, based on user-defined pressure and flow velocity constraints. To the best of our knowledge, there is no available open-source software for this purpose, which allows for case-specific modifications/interventions by advanced users, as well as extensions to weight between alternative design strategies. Therefore, UPStream® is expected to serve as a useful tool/platform for educational/academic purposes, research, and engineering practice.

  18. An Algorithm for the Mixed Transportation Network Design Problem.

    Science.gov (United States)

    Liu, Xinyu; Chen, Qun

    2016-01-01

    This paper proposes an optimization algorithm, the dimension-down iterative algorithm (DDIA), for solving a mixed transportation network design problem (MNDP), which is generally expressed as a mathematical programming with equilibrium constraint (MPEC). The upper level of the MNDP aims to optimize the network performance via both the expansion of the existing links and the addition of new candidate links, whereas the lower level is a traditional Wardrop user equilibrium (UE) problem. The idea of the proposed solution algorithm (DDIA) is to reduce the dimensions of the problem. A group of variables (discrete/continuous) is fixed to optimize another group of variables (continuous/discrete) alternately; then, the problem is transformed into solving a series of CNDPs (continuous network design problems) and DNDPs (discrete network design problems) repeatedly until the problem converges to the optimal solution. The advantage of the proposed algorithm is that its solution process is very simple and easy to apply. Numerical examples show that for the MNDP without budget constraint, the optimal solution can be found within a few iterations with DDIA. For the MNDP with budget constraint, however, the result depends on the selection of initial values, which leads to different optimal solutions (i.e., different local optimal solutions). Some thoughts are given on how to derive meaningful initial values, such as by considering the budgets of new and reconstruction projects separately.

  19. Synthesis and Design of a Sustainable CO2 Utilization Network

    DEFF Research Database (Denmark)

    Frauzem, Rebecca; Gani, Rafiqul

    a superstructure-based approach a network of utilization alternatives is created linking CO2 and other raw materials with various products using processing blocks. This will then be optimized and verified for sustainability. Detailed design has also been performed for a case study on the methanol synthesis...... and requires work for implementation at an industrial level. One aspect of this is the development of a methodology for the formulation and optimization of sustainable conversion processes. This methodology follows three stages for the process synthesis, design and more sustainable design. Using...

  20. Microarchitecture of network-on-chip routers a designer's perspective

    CERN Document Server

    Dimitrakopoulos, Giorgos; Seitanidis, Ioannis

    2014-01-01

    This book provides a unified overview of network-on-chip router micro-architecture, the corresponding design opportunities and challenges, and existing solutions to overcome these challenges. The discussion focuses on the heart of a NoC, the NoC router, and how it interacts with the rest of the system. Coverage includes both basic and advanced design techniques that cover the entire router design space including router organization, flow control, pipelined operation, buffering architectures, as well as allocators' structure and algorithms. Router micro-architectural options are presented in a

  1. Toward Designing a Quantum Key Distribution Network Simulation Model

    Directory of Open Access Journals (Sweden)

    Miralem Mehic

    2016-01-01

    Full Text Available As research in quantum key distribution network technologies grows larger and more complex, the need for highly accurate and scalable simulation technologies becomes important to assess the practical feasibility and foresee difficulties in the practical implementation of theoretical achievements. In this paper, we described the design of simplified simulation environment of the quantum key distribution network with multiple links and nodes. In such simulation environment, we analyzed several routing protocols in terms of the number of sent routing packets, goodput and Packet Delivery Ratio of data traffic flow using NS-3 simulator.

  2. DESIGN OF BUILDING AUTOMATION BASED ON PROFIBUS-DP NETWORK

    Directory of Open Access Journals (Sweden)

    Cemal YILMAZ

    2006-02-01

    Full Text Available In this study, a building automation has been designed by using the Profibus DP (Process Field Bus- Decentralized Periphery network. In the study; fire alarm, thief alarm, lighting, power, humidity and temperature control have been implemented. The data from building has been transmitted to the Profibus-DP network via control point located on the flats. The data taken from the building has been collected in the main control unit to achieve overall control of the system. The work has provided an optimum efficiency in energy consumption, control of power, security, temperature and humidity.

  3. Optimizing Intermodal Train Schedules with a Design Balanced Network Design Model

    DEFF Research Database (Denmark)

    Pedersen, Michael Berliner; Crainic, Teodor Gabriel

    We present a modeling approach for optimizing intermodal trains schedules based on an infrastructure divided into time-dependent train paths. The formulation can be generalized to a capacitated multi commodity network design model with additional design balance constraints. We present a Tabu Search...

  4. Bird and Small Animal Tracking Using a GSM-based System

    Directory of Open Access Journals (Sweden)

    Samuel Matos

    2015-11-01

    Full Text Available This paper describes a prototype of a system designed to track animals, goods or persons. The system is based exclusively on Global System for Mobile Communications (GSM services, which are presently widespread. Its advantages and drawbacks are also discussed. The system itself consists of two independent parts: the base device and the location device. The location device is the part actually attached to the animal, good or person being tracked. It combines reduced size and weight with extended range. The base device can deal with one or more location devices. Its role is to receive the Short Message Service (SMS sent by the location devices and forward them to an application that decodes and stores the location data in a database. Since energy considerations and testing are fundamental in this context, we present detailed energy consumption profiles and the computer applications developed to test the system. We also discuss the results of practical tests with wild and captive birds.

  5. A method of network topology optimization design considering application process characteristic

    Science.gov (United States)

    Wang, Chunlin; Huang, Ning; Bai, Yanan; Zhang, Shuo

    2018-03-01

    Communication networks are designed to meet the usage requirements of users for various network applications. The current studies of network topology optimization design mainly considered network traffic, which is the result of network application operation, but not a design element of communication networks. A network application is a procedure of the usage of services by users with some demanded performance requirements, and has obvious process characteristic. In this paper, we first propose a method to optimize the design of communication network topology considering the application process characteristic. Taking the minimum network delay as objective, and the cost of network design and network connective reliability as constraints, an optimization model of network topology design is formulated, and the optimal solution of network topology design is searched by Genetic Algorithm (GA). Furthermore, we investigate the influence of network topology parameter on network delay under the background of multiple process-oriented applications, which can guide the generation of initial population and then improve the efficiency of GA. Numerical simulations show the effectiveness and validity of our proposed method. Network topology optimization design considering applications can improve the reliability of applications, and provide guidance for network builders in the early stage of network design, which is of great significance in engineering practices.

  6. Eesti allilm suudab tõkestada GSM-levi / Rasmus Kagge

    Index Scriptorium Estoniae

    Kagge, Rasmus, 1977-

    2006-01-01

    Ilmunud ka: Postimees : na russkom jazõke 10. mai lk. 2. Politsei andmetel on Eesti kuritegelike jõukude käes praegu vähemalt paar GSM-levi segajat ehk jammerit. Politseil on õnnestunud konfiskeerida autovarastelt üks GSM-levi tõkestaja. Lisa. Kasutajapiirang. Vt. samas: Jammereid saab osta internetist

  7. Design and Application of Nanogel-Based Polymer Networks

    Science.gov (United States)

    Dailing, Eric Alan

    Crosslinked polymer networks have wide application in biomaterials, from soft hydrogel scaffolds for cell culture and tissue engineering to glassy, high modulus dental restoratives. Composite materials formed with nanogels as a means for tuning network structure on the nanoscale have been reported, but no investigation into nanogels as the primary network component has been explored to this point. This thesis was dedicated to studying network formation from the direct polymerization of nanogels and investigating applications for these unique materials. Covalently crosslinked polymer networks were synthesized from polymerizable nanogels without the use of reactive small monomers or oligomers. Network properties were controlled by the chemical and physical properties of the nanogel, allowing for materials to be designed from nanostructured macromolecular precursors. Nanogels were synthesized from a thermally initiated solution free radical polymerization of a monomethacrylate, a dimethacrylate, and a thiol-based chain transfer agent. Monomers with a range of hydrophilic and hydrophobic character were copolymerized, and polymerizable groups were introduced through an alcohol-isocyanate click reaction. Nanogels were dispersible in water up to 75 wt%, including nanogels that contained a relatively high fraction of a conventionally water-insoluble component. Nanogels with molecular weights that ranged from 10's to 100's of kDa and hydrodynamic radii between 4 and 10 nm were obtained. Macroscopic crosslinked polymer networks were synthesized from the photopolymerization of methacrylate-functionalized nanogels in inert solvent, which was typically water. The nanogel composition and internal branching density affected both covalent and non-covalent interparticle interactions, which dictated the final mechanical properties of the networks. Nanogels with progressively disparate hydrophilic and hydrophobic character were synthesized to explore the potential for creating

  8. Spatiotemporal Scaling Effect on Rainfall Network Design Using Entropy

    Directory of Open Access Journals (Sweden)

    Chiang Wei

    2014-08-01

    Full Text Available Because of high variation in mountainous areas, rainfall data at different spatiotemporal scales may yield potential uncertainty for network design. However, few studies focus on the scaling effect on both the spatial and the temporal scale. By calculating the maximum joint entropy of hourly typhoon events, monthly, six dry and wet months and annual rainfall between 1992 and 2012 for 1-, 3-, and 5-km grids, the relocated candidate rain gauges in the National Taiwan University Experimental Forest of Central Taiwan are prioritized. The results show: (1 the network exhibits different locations for first prioritized candidate rain gauges for different spatiotemporal scales; (2 the effect of spatial scales is insignificant compared to temporal scales; and (3 a smaller number and a lower percentage of required stations (PRS reach stable joint entropy for a long duration at finer spatial scale. Prioritized candidate rain gauges provide key reference points for adjusting the network to capture more accurate information and minimize redundancy.

  9. Mixed Transportation Network Design under a Sustainable Development Perspective

    Directory of Open Access Journals (Sweden)

    Jin Qin

    2013-01-01

    Full Text Available A mixed transportation network design problem considering sustainable development was studied in this paper. Based on the discretization of continuous link-grade decision variables, a bilevel programming model was proposed to describe the problem, in which sustainability factors, including vehicle exhaust emissions, land-use scale, link load, and financial budget, are considered. The objective of the model is to minimize the total amount of resources exploited under the premise of meeting all the construction goals. A heuristic algorithm, which combined the simulated annealing and path-based gradient projection algorithm, was developed to solve the model. The numerical example shows that the transportation network optimized with the method above not only significantly alleviates the congestion on the link, but also reduces vehicle exhaust emissions within the network by up to 41.56%.

  10. Design of experiment for nonlinear dynamic gene regulatory network identification.

    Science.gov (United States)

    Lu, Tao

    2017-04-04

    The gene regulatory network (GRN) is critical for understanding the regulatory interaction between genes. Time-course microarray experiments provide ample information for constructing GRN. The designs for microarray experiments serve different purposes. However, the experiment design specifically for GRN identification is still sparse. In this article, we use a simulation-based approach to deal with design problems in the framework of nonparametric differential equations. We investigate a number of feasible designs. In particular, we evaluate whether earlier samplings can result in more useful information for GRN identification. We also evaluate the effectiveness of two strategies: more frequent samplings per replicate with fewer replicates versus fewer samplings per replicate with more replicates while keeping the total number of samplings constant. The results of our investigation provide quantitative guidance for designing and selecting microarray experiments for the purpose of GRN identification.

  11. Design and implementation of a high performance network security processor

    Science.gov (United States)

    Wang, Haixin; Bai, Guoqiang; Chen, Hongyi

    2010-03-01

    The last few years have seen many significant progresses in the field of application-specific processors. One example is network security processors (NSPs) that perform various cryptographic operations specified by network security protocols and help to offload the computation intensive burdens from network processors (NPs). This article presents a high performance NSP system architecture implementation intended for both internet protocol security (IPSec) and secure socket layer (SSL) protocol acceleration, which are widely employed in virtual private network (VPN) and e-commerce applications. The efficient dual one-way pipelined data transfer skeleton and optimised integration scheme of the heterogenous parallel crypto engine arrays lead to a Gbps rate NSP, which is programmable with domain specific descriptor-based instructions. The descriptor-based control flow fragments large data packets and distributes them to the crypto engine arrays, which fully utilises the parallel computation resources and improves the overall system data throughput. A prototyping platform for this NSP design is implemented with a Xilinx XC3S5000 based FPGA chip set. Results show that the design gives a peak throughput for the IPSec ESP tunnel mode of 2.85 Gbps with over 2100 full SSL handshakes per second at a clock rate of 95 MHz.

  12. Conceptual design of a measurement network of the global change

    Directory of Open Access Journals (Sweden)

    P. Hari

    2016-01-01

    Full Text Available The global environment is changing rapidly due to anthropogenic emissions and actions. Such activities modify aerosol and greenhouse gas concentrations in the atmosphere, leading to regional and global climate change and affecting, e.g., food and fresh-water security, sustainable use of natural resources and even demography. Here we present a conceptual design of a global, hierarchical observation network that can provide tools and increased understanding to tackle the inter-connected environmental and societal challenges that we will face in the coming decades. The philosophy behind the conceptual design relies on physical conservation laws of mass, energy and momentum, as well as on concentration gradients that act as driving forces for the atmosphere-biosphere exchange. The network is composed of standard, flux and/or advanced and flagship stations, each of which having specific and identified tasks. Each ecosystem type on the globe has its own characteristic features that have to be taken into consideration. The hierarchical network as a whole is able to tackle problems related to large spatial scales, heterogeneity of ecosystems and their complexity. The most comprehensive observations are envisioned to occur in flagship stations, with which the process-level understanding can be expanded to continental and global scales together with advanced data analysis, Earth system modelling and satellite remote sensing. The denser network of the flux and standard stations allows application and up-scaling of the results obtained from flagship stations to the global level.

  13. Design of Optical Wireless Networks with Fair Traffic Flows

    Directory of Open Access Journals (Sweden)

    Artur Tomaszewski

    2014-01-01

    Full Text Available The paper presents a method for optimising the wireless optical network that carries elastic packet traffic. The particular focus is on modelling the effect of elastic traffic flows slowing down in response to the decrease of the optical transmission systems’ capacity at bad weather conditions. A mathematical programming model of the network design problem is presented that assumes that the packet rates of elastic traffic flows decrease fairly. While practically any subset of network links can be simultaneously affected by unfavourable transmission conditions, a particular challenge of solving the problem results from a huge number of network states considered in the model. Therefore, how the problem can be solved by generating the most unfavourable network states is presented. Moreover, it is proved that it is entirely sufficient to consider only the states that correspond to the decrease of capacity on a single link. Finally, as the general problem is nonlinear, it is shown that the problem can be transformed to a linear MIP problem and solved effectively when single-path routing of traffic flows is assumed.

  14. On the Complexities of the Design of Water Distribution Networks

    Directory of Open Access Journals (Sweden)

    Joaquín Izquierdo

    2012-01-01

    Full Text Available Water supply is one of the most recognizable and important public services contributing to quality of life. Water distribution networks (WDNs are extremely complex assets. A number of complex tasks, such as design, planning, operation, maintenance, and management, are inherently associated with such networks. In this paper, we focus on the design of a WDN, which is a wide and open problem in hydraulic engineering. This problem is a large-scale combinatorial, nonlinear, nonconvex, multiobjective optimization problem, involving various types of decision variables and many complex implicit constraints. To handle this problem, we provide a synergetic association between swarm intelligence and multiagent systems where human interaction is also enabled. This results in a powerful collaborative system for finding solutions to such a complex hydraulic engineering problem. All the ingredients have been integrated into a software tool that has also been shown to efficiently solve problems from other engineering fields.

  15. Designing a Pregnancy Care Network for Pregnant Women

    Directory of Open Access Journals (Sweden)

    Sabiha Khanum

    2017-12-01

    Full Text Available All pregnant women need easy access to pregnancy-related personalized information, on-time quality healthcare services and effective communication links with healthcare providers. Smartphone-based devices, communication systems and eHealth applications can play an important role in facilitating some of these services to pregnant women in a fast and efficient way and can thus prevent most of the pregnancy-related complications. The objective of this work is to propose and design a pregnancy care network for pregnant women and healthcare providers. The network model, an eHealth application based on smartphone-based devices and communication systems, is designed to strengthen communication links between health professionals and pregnant women and increase education, awareness and quality of care during pregnancy and childbirth.

  16. Multi-objective optimization framework for networked predictive controller design.

    Science.gov (United States)

    Das, Sourav; Das, Saptarshi; Pan, Indranil

    2013-01-01

    Networked Control Systems (NCSs) often suffer from random packet dropouts which deteriorate overall system's stability and performance. To handle the ill effects of random packet losses in feedback control systems, closed over communication network, a state feedback controller with predictive gains has been designed. To achieve improved performance, an optimization based controller design framework has been proposed in this paper with Linear Matrix Inequality (LMI) constraints, to ensure guaranteed stability. Different conflicting objective functions have been optimized with Non-dominated Sorting Genetic Algorithm-II (NSGA-II). The methodology proposed in this paper not only gives guaranteed closed loop stability in the sense of Lyapunov, even in the presence of random packet losses, but also gives an optimization trade-off between two conflicting time domain control objectives. Copyright © 2012 ISA. All rights reserved.

  17. Designing a Fuzzy Strategic Integrated Multiechelon Agile Supply Chain Network

    Directory of Open Access Journals (Sweden)

    Morteza Abbasi

    2013-01-01

    Full Text Available This paper integrates production, distribution and logistics activities at the strategic decision making level, where the objective is to design a multiechelon supply chain network considering agility as a key design criterion. A network with five echelons of supply chains including suppliers, plants, distribution centers, cross-docks, and customer zones is addressed in this paper. The problem has been mathematically formulated as a biobjective optimization model that aims to minimize the cost (fixed and variable and maximize the plant flexibility and volume flexibility. A novel multiobjective parallel simulating annealing algorithm (MOPSA is proposed to obtain the Pareto-optimal solutions of the problem. The performance of the proposed solution algorithm is compared with two well-known metaheuristics, namely, nondominated sorting genetic algorithm (NSGA-II and Pareto archive evolution strategy (PAES. Computational results show that MOPSA outperforms the other metaheuristics.

  18. Fiber-Optic Transmission Networks Efficient Design and Dynamic Operation

    CERN Document Server

    Pachnicke, Stephan

    2012-01-01

    Next generation optical communication systems will have to transport a significantly increased data volume at a reduced cost per transmitted bit. To achieve these ambitious goals optimum design is crucial in combination with dynamic adaptation to actual traffic demands and improved energy efficiency. In the first part of the book the author elaborates on the design of optical transmission systems. Several methods for efficient numerical simulation are presented ranging from meta-model based optimization to parallelization techniques for solving the nonlinear Schrödinger equation. Furthermore, fast analytical and semi-analytical models are described to estimate the various degradation effects occurring on the transmission line. In the second part of the book operational aspects of optical networks are investigated. Physical layer impairment-aware routing and regenerator placement are studied. Finally, it is analyzed how the energy efficiency of a multi-layer optical core network can be increased by dynamic ad...

  19. Peer-to-Peer Networks: A Mechanism Design Approach

    OpenAIRE

    Oksana Loginova; X. Henry Wang; Haibin Lu

    2006-01-01

    In this paper we use mechanism design approach to find the optimal file-sharing mechanism in a peer-to-peer network. This mechanism improves upon existing incentive schemes. In particular, we show that peer-approved scheme is never optimal and service-quality scheme is optimal only under certain circumstances. Moreover, we find that the optimal mechanism can be implemented by a mixture of peer-approved and service-quality schemes.

  20. Very Small Satellite Design for Space Sensor Networks

    Science.gov (United States)

    2008-06-01

    hard anodized Cold welding not possible with Delrin/anodized aluminium combo. Exception 12. Custom intersatellite separation springs may be used...Network Architecture Design 48 Table 3-7. MESA Data Packet Bytes Description 3 Unique identifier and status flags 17 Time and location stamp ...and mass requirements for such a system. The vacuum of space introduces several issues, such as cold welding and outgassing, but for very small

  1. District Heating Network Design and Configuration Optimization with Genetic Algorithm

    DEFF Research Database (Denmark)

    Li, Hongwei; Svendsen, Svend

    2011-01-01

    the heating plant location is allowed to vary. The connection between the heat generation plant and the end users can be represented with mixed integer and the pipe friction and heat loss formulations are non-linear. In order to find the optimal DH distribution pipeline configuration, the genetic algorithm...... by multi factors as the consumer heating load, the distance between the heating plant to the consumer, the design criteria regarding pressure and temperature limitation, as well as the corresponding network heat loss....

  2. Designing Knowledge of The PPC with Semantic Network

    Science.gov (United States)

    Fajar Santoso, Ari; Supriana, Iping; Surendro, Kridanto

    2017-01-01

    A manufacturing process is a very complex activity, which involves a variety of knowledge, such as the product design and description, manufacturing operations, tools, machines, and the relationships between these entities. Production planning control (PPC) as dominant part of manufacturing process has a very important role in determining the measures taken by the management of company. The PPC construction is an interactive process that requires the collaboration of both ICT and manufacture experts. Building PPC process can be used as a basis for making knowledge in manufacturing domain that will be used in manufacturing intelligent system. This paper describes about designing knowledge with semantic network in the production scheduling.

  3. Network design and analysis for multi-enzyme biocatalysis.

    Science.gov (United States)

    Blaß, Lisa Katharina; Weyler, Christian; Heinzle, Elmar

    2017-08-10

    As more and more biological reaction data become available, the full exploration of the enzymatic potential for the synthesis of valuable products opens up exciting new opportunities but is becoming increasingly complex. The manual design of multi-step biosynthesis routes involving enzymes from different organisms is very challenging. To harness the full enzymatic potential, we developed a computational tool for the directed design of biosynthetic production pathways for multi-step catalysis with in vitro enzyme cascades, cell hydrolysates and permeabilized cells. We present a method which encompasses the reconstruction of a genome-scale pan-organism metabolic network, path-finding and the ranking of the resulting pathway candidates for proposing suitable synthesis pathways. The network is based on reaction and reaction pair data from the Kyoto Encyclopedia of Genes and Genomes (KEGG) and the thermodynamics calculator eQuilibrator. The pan-organism network is especially useful for finding the most suitable pathway to a target metabolite from a thermodynamic or economic standpoint. However, our method can be used with any network reconstruction, e.g. for a specific organism. We implemented a path-finding algorithm based on a mixed-integer linear program (MILP) which takes into account both topology and stoichiometry of the underlying network. Unlike other methods we do not specify a single starting metabolite, but our algorithm searches for pathways starting from arbitrary start metabolites to a target product of interest. Using a set of biochemical ranking criteria including pathway length, thermodynamics and other biological characteristics such as number of heterologous enzymes or cofactor requirement, it is possible to obtain well-designed meaningful pathway alternatives. In addition, a thermodynamic profile, the overall reactant balance and potential side reactions as well as an SBML file for visualization are generated for each pathway alternative. We present

  4. New knowledge network evaluation method for design rationale management

    Science.gov (United States)

    Jing, Shikai; Zhan, Hongfei; Liu, Jihong; Wang, Kuan; Jiang, Hao; Zhou, Jingtao

    2015-01-01

    Current design rationale (DR) systems have not demonstrated the value of the approach in practice since little attention is put to the evaluation method of DR knowledge. To systematize knowledge management process for future computer-aided DR applications, a prerequisite is to provide the measure for the DR knowledge. In this paper, a new knowledge network evaluation method for DR management is presented. The method characterizes the DR knowledge value from four perspectives, namely, the design rationale structure scale, association knowledge and reasoning ability, degree of design justification support and degree of knowledge representation conciseness. The DR knowledge comprehensive value is also measured by the proposed method. To validate the proposed method, different style of DR knowledge network and the performance of the proposed measure are discussed. The evaluation method has been applied in two realistic design cases and compared with the structural measures. The research proposes the DR knowledge evaluation method which can provide object metric and selection basis for the DR knowledge reuse during the product design process. In addition, the method is proved to be more effective guidance and support for the application and management of DR knowledge.

  5. Multi-dimensional design window search system using neural networks in reactor core design

    International Nuclear Information System (INIS)

    Kugo, Teruhiko; Nakagawa, Masayuki

    2000-02-01

    In the reactor core design, many parametric survey calculations should be carried out to decide an optimal set of basic design parameter values. They consume a large amount of computation time and labor in the conventional way. To support directly design work, we investigate a procedure to search efficiently a design window, which is defined as feasible design parameter ranges satisfying design criteria and requirements, in a multi-dimensional space composed of several basic design parameters. We apply the present method to the neutronics and thermal hydraulics fields and develop the multi-dimensional design window search system using it. The principle of the present method is to construct the multilayer neural network to simulate quickly a response of an analysis code through a training process, and to reduce computation time using the neural network without parametric study using analysis codes. The system works on an engineering workstation (EWS) with efficient man-machine interface for pre- and post-processing. This report describes the principle of the present method, the structure of the system, the guidance of the usages of the system, the guideline for the efficient training of neural networks, the instructions of the input data for analysis calculation and so on. (author)

  6. An outer approximation method for the road network design problem.

    Science.gov (United States)

    Asadi Bagloee, Saeed; Sarvi, Majid

    2018-01-01

    Best investment in the road infrastructure or the network design is perceived as a fundamental and benchmark problem in transportation. Given a set of candidate road projects with associated costs, finding the best subset with respect to a limited budget is known as a bilevel Discrete Network Design Problem (DNDP) of NP-hard computationally complexity. We engage with the complexity with a hybrid exact-heuristic methodology based on a two-stage relaxation as follows: (i) the bilevel feature is relaxed to a single-level problem by taking the network performance function of the upper level into the user equilibrium traffic assignment problem (UE-TAP) in the lower level as a constraint. It results in a mixed-integer nonlinear programming (MINLP) problem which is then solved using the Outer Approximation (OA) algorithm (ii) we further relax the multi-commodity UE-TAP to a single-commodity MILP problem, that is, the multiple OD pairs are aggregated to a single OD pair. This methodology has two main advantages: (i) the method is proven to be highly efficient to solve the DNDP for a large-sized network of Winnipeg, Canada. The results suggest that within a limited number of iterations (as termination criterion), global optimum solutions are quickly reached in most of the cases; otherwise, good solutions (close to global optimum solutions) are found in early iterations. Comparative analysis of the networks of Gao and Sioux-Falls shows that for such a non-exact method the global optimum solutions are found in fewer iterations than those found in some analytically exact algorithms in the literature. (ii) Integration of the objective function among the constraints provides a commensurate capability to tackle the multi-objective (or multi-criteria) DNDP as well.

  7. Optimization model for the design of distributed wastewater treatment networks

    Directory of Open Access Journals (Sweden)

    Ibrić Nidret

    2012-01-01

    Full Text Available In this paper we address the synthesis problem of distributed wastewater networks using mathematical programming approach based on the superstructure optimization. We present a generalized superstructure and optimization model for the design of the distributed wastewater treatment networks. The superstructure includes splitters, treatment units, mixers, with all feasible interconnections including water recirculation. Based on the superstructure the optimization model is presented. The optimization model is given as a nonlinear programming (NLP problem where the objective function can be defined to minimize the total amount of wastewater treated in treatment operations or to minimize the total treatment costs. The NLP model is extended to a mixed integer nonlinear programming (MINLP problem where binary variables are used for the selection of the wastewater treatment technologies. The bounds for all flowrates and concentrations in the wastewater network are specified as general equations. The proposed models are solved using the global optimization solvers (BARON and LINDOGlobal. The application of the proposed models is illustrated on the two wastewater network problems of different complexity. First one is formulated as the NLP and the second one as the MINLP. For the second one the parametric and structural optimization is performed at the same time where optimal flowrates, concentrations as well as optimal technologies for the wastewater treatment are selected. Using the proposed model both problems are solved to global optimality.

  8. Runtime reconfiguration in networked embedded systems design and testing practices

    CERN Document Server

    Exarchakos, George

    2016-01-01

    This book focuses on the design and testing of large-scale, distributed signal processing systems, with a special emphasis on systems architecture, tooling and best practices. Architecture modeling, model checking, model-based evaluation and model-based design optimization occupy central roles. Target systems with resource constraints on processing, communication or energy supply require non-trivial methodologies to model their non-functional requirements, such as timeliness, robustness, lifetime and “evolution” capacity. Besides the theoretical foundations of the methodology, an engineering process and toolchain are described. Real-world cases illustrate the theory and practice tested by the authors in the course of the European project ARTEMIS DEMANES. The book can be used as a “cookbook” for designers and practitioners working with complex embedded systems like sensor networks for the structural integrity monitoring of steel bridges, and distributed micro-climate control systems for greenhouses and...

  9. Chemical reaction network designs for asynchronous logic circuits.

    Science.gov (United States)

    Cardelli, Luca; Kwiatkowska, Marta; Whitby, Max

    2018-01-01

    Chemical reaction networks (CRNs) are a versatile language for describing the dynamical behaviour of chemical kinetics, capable of modelling a variety of digital and analogue processes. While CRN designs for synchronous sequential logic circuits have been proposed and their implementation in DNA demonstrated, a physical realisation of these devices is difficult because of their reliance on a clock. Asynchronous sequential logic, on the other hand, does not require a clock, and instead relies on handshaking protocols to ensure the temporal ordering of different phases of the computation. This paper provides novel CRN designs for the construction of asynchronous logic, arithmetic and control flow elements based on a bi-molecular reaction motif with catalytic reactions and uniform reaction rates. We model and validate the designs for the deterministic and stochastic semantics using Microsoft's GEC tool and the probabilistic model checker PRISM, demonstrating their ability to emulate the function of asynchronous components under low molecular count.

  10. An architecture for designing fuzzy logic controllers using neural networks

    Science.gov (United States)

    Berenji, Hamid R.

    1991-01-01

    Described here is an architecture for designing fuzzy controllers through a hierarchical process of control rule acquisition and by using special classes of neural network learning techniques. A new method for learning to refine a fuzzy logic controller is introduced. A reinforcement learning technique is used in conjunction with a multi-layer neural network model of a fuzzy controller. The model learns by updating its prediction of the plant's behavior and is related to the Sutton's Temporal Difference (TD) method. The method proposed here has the advantage of using the control knowledge of an experienced operator and fine-tuning it through the process of learning. The approach is applied to a cart-pole balancing system.

  11. Design of a Distribution Network Using Primal-Dual Decomposition

    Directory of Open Access Journals (Sweden)

    J. A. Marmolejo

    2016-01-01

    Full Text Available A method to solve the design of a distribution network for bottled drinks company is introduced. The distribution network proposed includes three stages: manufacturing centers, consolidation centers using cross-docking, and distribution centers. The problem is formulated using a mixed-integer programming model in the deterministic and single period contexts. Because the problem considers several elements in each stage, a direct solution is very complicated. For medium-to-large instances the problem falls into large scale. Based on that, a primal-dual decomposition known as cross decomposition is proposed in this paper. This approach allows exploring simultaneously the primal and dual subproblems of the original problem. A comparison of the direct solution with a mixed-integer lineal programming solver versus the cross decomposition is shown for several randomly generated instances. Results show the good performance of the method proposed.

  12. Design of multi-phase dynamic chemical networks

    Science.gov (United States)

    Chen, Chenrui; Tan, Junjun; Hsieh, Ming-Chien; Pan, Ting; Goodwin, Jay T.; Mehta, Anil K.; Grover, Martha A.; Lynn, David G.

    2017-08-01

    Template-directed polymerization reactions enable the accurate storage and processing of nature's biopolymer information. This mutualistic relationship of nucleic acids and proteins, a network known as life's central dogma, is now marvellously complex, and the progressive steps necessary for creating the initial sequence and chain-length-specific polymer templates are lost to time. Here we design and construct dynamic polymerization networks that exploit metastable prion cross-β phases. Mixed-phase environments have been used for constructing synthetic polymers, but these dynamic phases emerge naturally from the growing peptide oligomers and create environments suitable both to nucleate assembly and select for ordered templates. The resulting templates direct the amplification of a phase containing only chain-length-specific peptide-like oligomers. Such multi-phase biopolymer dynamics reveal pathways for the emergence, self-selection and amplification of chain-length- and possibly sequence-specific biopolymers.

  13. Design of an IPTV Multicast System for Internet Backbone Networks

    Directory of Open Access Journals (Sweden)

    T. H. Szymanski

    2010-01-01

    Full Text Available The design of an IPTV multicast system for the Internet backbone network is presented and explored through extensive simulations. In the proposed system, a resource reservation algorithm such as RSVP, IntServ, or DiffServ is used to reserve resources (i.e., bandwidth and buffer space in each router in an IP multicast tree. Each router uses an Input-Queued, Output-Queued, or Crosspoint-Queued switch architecture with unity speedup. A recently proposed Recursive Fair Stochastic Matrix Decomposition algorithm used to compute near-perfect transmission schedules for each IP router. The IPTV traffic is shaped at the sources using Application-Specific Token Bucker Traffic Shapers, to limit the burstiness of incoming network traffic. The IPTV traffic is shaped at the destinations using Application-Specific Playback Queues, to remove residual network jitter and reconstruct the original bursty IPTV video streams at each destination. All IPTV traffic flows are regenerated at the destinations with essentially zero delay jitter and essentially-perfect QoS. The destination nodes deliver the IPTV streams to the ultimate end users using the same IPTV multicast system over a regional Metropolitan Area Network. It is shown that all IPTV traffic is delivered with essentially-perfect end-to-end QoS, with deterministic bounds on the maximum delay and jitter on each video frame. Detailed simulations of an IPTV distribution system, multicasting several hundred high-definition IPTV video streams over several essentially saturated IP backbone networks are presented.

  14. Neural Network Assisted Experimental Designs for Food Research

    Directory of Open Access Journals (Sweden)

    H.S. Ramaswamy

    2000-06-01

    Full Text Available The ability of artificial neural networks (ANN in predicting full factorial data from the fractional data corresponding to some of the commonly used experimental designs is explored in this paper. Factorial and fractional factorial designs such as L8, L9, L18, and Box and Behnken schemes were considered both in their original form and with some variations (L8+6, L15 and L9+1. Full factorial (3 factors x 5 levels and fractional data were generated employing sixteen different mathematical equations (four in each category: linear, with and without interactions, and non-linear, with and without interactions. Different ANN models were trained and the best model was chosen for each equation based on their ability to predict the fractional data. The best experimental design was then chosen based on their ability to simulate the full- factorial data for each equation. In several cases, the mean relative errors with the L18 design (which had more input data than other models were even higher than with other smaller fractional design. In general, the ANN assisted Lm, Box and Behnken, L15 and L18 designs were found to predict the full factorial data reasonably well with errors less than 5 %. The L8+6 model performed well with several experimental datasets reported in the literature.

  15. Games as Actors - Interaction, Play, Design, and Actor Network Theory

    DEFF Research Database (Denmark)

    Jessen, Jari Due; Jessen, Carsten

    2014-01-01

    When interacting with computer games, users are forced to follow the rules of the game in return for the excitement, joy, fun, or other pursued experiences. In this paper, we investigate how games a chieve these experiences in the perspective of Actor Network Theory (ANT). Based on a qualitative...... data from a study of board games , computer games, and exergames, we conclude that games are actors that produce experiences by exercising power over the user’ s abilities, for example their cognitive functions. Games are designed to take advantage of the characteristics of the human players...

  16. Optimizing Airborne Networking Performance with Cross-Layer Design Approach

    Science.gov (United States)

    2009-06-01

    simulation, we used open source XviD MPEG-4 compliant video codec [25]. Sixty seconds of a high motion video sequence (football match) are encoded at 15...Johnson, “Design and demonstration of live audio and video over multi-hop wireless networks,” In MILCOM, 2002. [12] T. Goff, N. Abu-Ghazaleh, D...24] E. Gilbert, “Capacity of a burst-noise channel,” Bell Syst. Tech. J., vol. 39, no. 9, pp. 1253-1265, Sept. 1960. [25] XviD MPEG-4 video codec

  17. Design and Performance Analysis of Incremental Networked Predictive Control Systems.

    Science.gov (United States)

    Pang, Zhong-Hua; Liu, Guo-Ping; Zhou, Donghua

    2016-06-01

    This paper is concerned with the design and performance analysis of networked control systems with network-induced delay, packet disorder, and packet dropout. Based on the incremental form of the plant input-output model and an incremental error feedback control strategy, an incremental networked predictive control (INPC) scheme is proposed to actively compensate for the round-trip time delay resulting from the above communication constraints. The output tracking performance and closed-loop stability of the resulting INPC system are considered for two cases: 1) plant-model match case and 2) plant-model mismatch case. For the former case, the INPC system can achieve the same output tracking performance and closed-loop stability as those of the corresponding local control system. For the latter case, a sufficient condition for the stability of the closed-loop INPC system is derived using the switched system theory. Furthermore, for both cases, the INPC system can achieve a zero steady-state output tracking error for step commands. Finally, both numerical simulations and practical experiments on an Internet-based servo motor system illustrate the effectiveness of the proposed method.

  18. Efficiency and robustness of different bus network designs

    Science.gov (United States)

    Pang, John Zhen Fu; Bin Othman, Nasri; Ng, Keng Meng; Monterola, Christopher

    2015-07-01

    We compare the efficiencies and robustness of four transport networks that can be possibly formed as a result of deliberate city planning. The networks are constructed based on their spatial resemblance to the cities of Manhattan (lattice), Sudan (random), Beijing (single-blob) and Greater Cairo (dual-blob). For a given type, a genetic algorithm is employed to obtain an optimized set of the bus routes. We then simulate how commuter travels using Yen's algorithms for k shortest paths on an adjacency matrix. The cost of traveling such as walking between stations is captured by varying the weighted sums of matrices. We also consider the number of transfers a posteriori by looking at the computed shortest paths. With consideration to distances via radius of gyration, redundancies of travel and number of bus transfers, our simulations indicate that random and dual-blob are more efficient than single-blob and lattice networks. Moreover, dual-blob type is least robust when node removals are targeted but is most resilient when node failures are random. The work hopes to guide and provide technical perspectives on how geospatial distribution of a city limits the optimality of transport designs.

  19. Designing Artificial Neural Networks Using Particle Swarm Optimization Algorithms

    Directory of Open Access Journals (Sweden)

    Beatriz A. Garro

    2015-01-01

    Full Text Available Artificial Neural Network (ANN design is a complex task because its performance depends on the architecture, the selected transfer function, and the learning algorithm used to train the set of synaptic weights. In this paper we present a methodology that automatically designs an ANN using particle swarm optimization algorithms such as Basic Particle Swarm Optimization (PSO, Second Generation of Particle Swarm Optimization (SGPSO, and a New Model of PSO called NMPSO. The aim of these algorithms is to evolve, at the same time, the three principal components of an ANN: the set of synaptic weights, the connections or architecture, and the transfer functions for each neuron. Eight different fitness functions were proposed to evaluate the fitness of each solution and find the best design. These functions are based on the mean square error (MSE and the classification error (CER and implement a strategy to avoid overtraining and to reduce the number of connections in the ANN. In addition, the ANN designed with the proposed methodology is compared with those designed manually using the well-known Back-Propagation and Levenberg-Marquardt Learning Algorithms. Finally, the accuracy of the method is tested with different nonlinear pattern classification problems.

  20. Generative Recurrent Networks for De Novo Drug Design.

    Science.gov (United States)

    Gupta, Anvita; Müller, Alex T; Huisman, Berend J H; Fuchs, Jens A; Schneider, Petra; Schneider, Gisbert

    2018-01-01

    Generative artificial intelligence models present a fresh approach to chemogenomics and de novo drug design, as they provide researchers with the ability to narrow down their search of the chemical space and focus on regions of interest. We present a method for molecular de novo design that utilizes generative recurrent neural networks (RNN) containing long short-term memory (LSTM) cells. This computational model captured the syntax of molecular representation in terms of SMILES strings with close to perfect accuracy. The learned pattern probabilities can be used for de novo SMILES generation. This molecular design concept eliminates the need for virtual compound library enumeration. By employing transfer learning, we fine-tuned the RNN's predictions for specific molecular targets. This approach enables virtual compound design without requiring secondary or external activity prediction, which could introduce error or unwanted bias. The results obtained advocate this generative RNN-LSTM system for high-impact use cases, such as low-data drug discovery, fragment based molecular design, and hit-to-lead optimization for diverse drug targets. © 2017 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

  1. An OCP Compliant Network Adapter for GALS-based SoC Design Using the MANGO Network-on-Chip

    DEFF Research Database (Denmark)

    Bjerregaard, Tobias; Mahadevan, Shankar; Olsen, Rasmus Grøndahl

    2005-01-01

    The demand for IP reuse and system level scalability in System-on-Chip (SoC) designs is growing. Network-onchip (NoC) constitutes a viable solution space to emerging SoC design challenges. In this paper we describe an OCP compliant network adapter (NA) architecture for the MANGO NoC. The NA...... decouples communication and computation, providing memory-mapped OCP transactions based on primitive message-passing services of the network. Also, it facilitates GALS-type systems, by adapting to the clockless network. This helps leverage a modular SoC design flow. We evaluate performance and cost of 0...

  2. Secure, Mobile, Wireless Network Technology Designed, Developed, and Demonstrated

    Science.gov (United States)

    Ivancic, William D.; Paulsen, Phillip E.

    2004-01-01

    The inability to seamlessly disseminate data securely over a high-integrity, wireless broadband network has been identified as a primary technical barrier to providing an order-of-magnitude increase in aviation capacity and safety. Secure, autonomous communications to and from aircraft will enable advanced, automated, data-intensive air traffic management concepts, increase National Air Space (NAS) capacity, and potentially reduce the overall cost of air travel operations. For the first time ever, secure, mobile, network technology was designed, developed, and demonstrated with state-ofthe- art protocols and applications by a diverse, cooperative Government-industry team led by the NASA Glenn Research Center. This revolutionary technology solution will make fundamentally new airplane system capabilities possible by enabling secure, seamless network connections from platforms in motion (e.g., cars, ships, aircraft, and satellites) to existing terrestrial systems without the need for manual reconfiguration. Called Mobile Router, the new technology autonomously connects and configures networks as they traverse from one operating theater to another. The Mobile Router demonstration aboard the Neah Bay, a U.S. Coast Guard vessel stationed in Cleveland, Ohio, accomplished secure, seamless interoperability of mobile network systems across multiple domains without manual system reconfiguration. The Neah Bay was chosen because of its low cost and communications mission similarity to low-Earth-orbiting satellite platforms. This technology was successfully advanced from technology readiness level (TRL) 2 (concept and/or application formation) to TRL 6 (system model or prototype demonstration in a relevant environment). The secure, seamless interoperability offered by the Mobile Router and encryption device will enable several new, vehicle-specific and systemwide technologies to perform such things as remote, autonomous aircraft performance monitoring and early detection and

  3. An engineering design network for SSC detector development

    International Nuclear Information System (INIS)

    DiGiacomo, N.J.

    1990-01-01

    The detector systems that are being proposed to exploit the capabilities of the SSC are of a scale and scope that will make them among the most complex devices ever built. To successfully design and build these systems over the next decade, the authors must make use of integrated state of the art computer aided engineering and design (CAE/CAD) tools that have been developed and employed in industry. The challenge is to made these tools and associated engineering resources available to the spectrum of institutions - large and small universities, industries and national labs - involved in SSC detector development in such a way that each may contribute and participate in the most effective manner. The authors believe that powerful workstations running sophisticated modeling, analysis and simulation software, linked by high speed data networks and governed by modern configuration management methods offer the ideal means of arriving at the optimum detector configuration for physics at the SSC

  4. Evaluation of Noise in Hearing Instruments Caused by GSM and DECT Mobile Telephones

    DEFF Research Database (Denmark)

    Hansen, Mie Østergaard; Poulsen, Torben

    1996-01-01

    word material mixed with GSM and DECT noise. The listening tests showed that if the noise level is acceptable so also is speech recognition. The results agree well with an investigation carried out on normal-hearing subjects. If a hearing instrument user is able to use a telephone without annoyance......The annoyance of noise in hearing instruments caused by electromagnetic interference from Global systems for Mobile Communication (GSM) and Digital European Cordless Telecommunication (DECT) mobile telephones has been subjectively evaluated by test subjects. The influence on speech recognition from...... the GSM and the DECT noises was also determined. The measurements involved seventeen hearing-imparied subjects. The annoyance was tested with GSM and DECT noise, each one mixed with continuous speech, a mall environment noise, or an office environment noise. Speech recognition was tested with the DANTALE...

  5. Q GSM tegi konkurentidele dünamo / Aivar Hundimägi

    Index Scriptorium Estoniae

    Hundimägi, Aivar, 1975-

    2004-01-01

    Mobiilsideoperaatorile Q GSM (praegune Tele2) edu taganud turundusstrateegiatest. Lisad: Q GSMi Dynamo teenuspaketi eesmärgid; Q GSMist sai Tele2. Diagramm: 2000. aastal turule toodud Dynamo pakett tõi murrangu

  6. "Intelligent" design of molecular materials: Understanding the concepts of design in supramolecular synthesis of network solids

    Science.gov (United States)

    Moulton, Brian D.

    This work endeavors to delineate modern paradigms for crystal engineering, i.e. the design and supramolecular synthesis of functional molecular materials. Paradigms predicated on an understanding of the geometry of polygons and polyhedra are developed. The primary focus is on structural determination by single crystal X-ray crystallography, structural interpretation using a suite of graphical visualization and molecular modeling software, and on the importance of proper graphical representation in the presentation and explanation of crystal structures. A detailed analysis of a selected series of crystal structures is presented. The reduction of these molecular networks to schematic representations that illustrate their fundamental connectivity facilitates the understanding of otherwise complex supramolecular solids. Circuit symbols and Schlafli notation are used to describe the network topologies, which enables networks of different composition and metrics to be easily compared. This reveals that molecular orientations in the crystals and networks are commensurate with networks that can be derived from spherical close packed lattices. The development of a logical design strategy for a new class of materials based on our understanding of the chemical composition and topology of these networks is described. The synthesis and crystal structure of a series of new materials generated by exploitation of this design strategy is presented, in addition to a detailed analysis of the topology of these materials and their relationship to a 'parent' structure. In summary, this dissertation demonstrates that molecular polygons can self-assemble at their vertexes to produce molecular architectures and crystal structures that are consistent with long established geometric dogma. The design strategy represents a potentially broad ranging approach to the design of nanoporous structures from a wide range of chemical components that are based on molecular shape rather than chemical

  7. Cross-Layer Design Approach for Power Control in Mobile Ad Hoc Networks

    OpenAIRE

    A. Sarfaraz Ahmed; T. Senthil Kumaran; S. Syed Abdul Syed; S. Subburam

    2015-01-01

    In mobile ad hoc networks, communication among mobile nodes occurs through wireless medium The design of ad hoc network protocol, generally based on a traditional “layered approach”, has been found ineffective to deal with receiving signal strength (RSS)-related problems, affecting the physical layer, the network layer and transport layer. This paper proposes a design approach, deviating from the traditional network design, toward enhancing the cross-layer interaction among different layers, ...

  8. Incorporating alternative design clinical trials in network meta-analyses

    Directory of Open Access Journals (Sweden)

    Thorlund K

    2014-12-01

    Full Text Available Kristian Thorlund,1–3 Eric Druyts,1,4 Kabirraaj Toor,1,5 Jeroen P Jansen,1,6 Edward J Mills1,3 1Redwood Outcomes, Vancouver, BC, 2Department of Clinical Epidemiology and Biostatistics, McMaster University, Hamilton, ON, Canada; 3Stanford Prevention Research Center, Stanford University, Stanford, CA, USA; 4Department of Medicine, Faculty of Medicine, 5School of Population and Public Health, Faculty of Medicine, University of British Columbia, Vancouver, BC, Canada; 6Department of Public Health and Community Medicine, Tufts University, Boston, MA, USA Introduction: Network meta-analysis (NMA is an extension of conventional pairwise meta-analysis that allows for simultaneous comparison of multiple interventions. Well-established drug class efficacies have become commonplace in many disease areas. Thus, for reasons of ethics and equipoise, it is not practical to randomize patients to placebo or older drug classes. Unique randomized clinical trial designs are an attempt to navigate these obstacles. These alternative designs, however, pose challenges when attempting to incorporate data into NMAs. Using ulcerative colitis as an example, we illustrate an example of a method where data provided by these trials are used to populate treatment networks. Methods: We present the methods used to convert data from the PURSUIT trial into a typical parallel design for inclusion in our NMA. Data were required for three arms: golimumab 100 mg; golimumab 50 mg; and placebo. Golimumab 100 mg induction data were available; however, data regarding those individuals who were nonresponders at induction and those who were responders at maintenance were not reported, and as such, had to be imputed using data from the rerandomization phase. Golimumab 50 mg data regarding responses at week 6 were not available. Existing relationships between the available components were used to impute the expected proportions in this missing subpopulation. Data for placebo maintenance

  9. Recurrent Neural Network Model for Constructive Peptide Design.

    Science.gov (United States)

    Müller, Alex T; Hiss, Jan A; Schneider, Gisbert

    2018-02-26

    We present a generative long short-term memory (LSTM) recurrent neural network (RNN) for combinatorial de novo peptide design. RNN models capture patterns in sequential data and generate new data instances from the learned context. Amino acid sequences represent a suitable input for these machine-learning models. Generative models trained on peptide sequences could therefore facilitate the design of bespoke peptide libraries. We trained RNNs with LSTM units on pattern recognition of helical antimicrobial peptides and used the resulting model for de novo sequence generation. Of these sequences, 82% were predicted to be active antimicrobial peptides compared to 65% of randomly sampled sequences with the same amino acid distribution as the training set. The generated sequences also lie closer to the training data than manually designed amphipathic helices. The results of this study showcase the ability of LSTM RNNs to construct new amino acid sequences within the applicability domain of the model and motivate their prospective application to peptide and protein design without the need for the exhaustive enumeration of sequence libraries.

  10. Preliminary Design Study for a National Digital Seismograph Network

    Science.gov (United States)

    Peterson, Jon; Hutt, Charles R.

    1981-01-01

    Introduction Recently, the National Research Council published a report by the Panel on National, Regional, and Local Seismograph Networks of the Committee on Seismology in which the principal recommendation was for the establishment of a national digital seismograph network (NDSN). The Panel Report (Bolt, 1980) addresses both the need and the scientific requirements for the new national network. The purpose of this study has been to translate the scientific requirements into an instrumentation concept for the NSDS. There are literally hundreds, perhaps thousands, of seismographs in operation within the United States. Each serves an important purpose, but most have limited objectives in time, in region, or in the types of data that are being recorded. The concept of a national network, funded and operated by the Federal Government, is based on broader objectives that include continuity of time, uniform coverage, standardization of data format and instruments, and widespread use of the data for a variety of research purposes. A national digital seismograph network will be an important data resource for many years to come; hence, its design is likely to be of interest to most seismologists. Seismologists have traditionally been involved in the development and field operation of seismic systems and thus have been familiar with both the potential value and the limitations of the data. However, in recent years of increasing technological sophistication, the development of data sstems has fallen more to system engineers, and this trend is likely to continue. One danger in this is that the engineers may misinterpret scientific objectives or subordinate them to purely technological considerations. Another risk is that the data users may misuse or misinterpret the data because they are not aware of the limitations of the data system. Perhaps the most important purpose of a design study such as this is to stimulate a dialogue between system engineers and potential data users

  11. Models and Tabu Search Metaheuristics for Service Network Design with Asset-Balance Requirements

    DEFF Research Database (Denmark)

    Pedersen, Michael Berliner; Crainic, T.G.; Madsen, Oli B.G.

    2009-01-01

    This paper focuses on a generic model for service network design, which includes asset positioning and utilization through constraints on asset availability at terminals. We denote these relations as "design-balance constraints" and focus on the design-balanced capacitated multicommodity network...... design model, a generalization of the capacitated multicommodity network design model generally used in service network design applications. Both arc-and cycle-based formulations for the new model are presented. The paper also proposes a tabu search metaheuristic framework for the arc-based formulation...

  12. Design of Supply Chain Networks with Supply Disruptions using Genetic Algorithm

    OpenAIRE

    Taha, Raghda; Abdallah, Khaled; Sadek, Yomma; El-Kharbotly, Amin; Afia, Nahid

    2014-01-01

    The design of supply chain networks subject to disruptions is tackled. A genetic algorithm with the objective of minimizing the design cost and regret cost is developed to achieve a reliable supply chain network. The improvement of supply chain network reliability is measured against the supply chain cost.

  13. Information theory-based decision support system for integrated design of multivariable hydrometric networks

    Science.gov (United States)

    Keum, Jongho; Coulibaly, Paulin

    2017-07-01

    Adequate and accurate hydrologic information from optimal hydrometric networks is an essential part of effective water resources management. Although the key hydrologic processes in the water cycle are interconnected, hydrometric networks (e.g., streamflow, precipitation, groundwater level) have been routinely designed individually. A decision support framework is proposed for integrated design of multivariable hydrometric networks. The proposed method is applied to design optimal precipitation and streamflow networks simultaneously. The epsilon-dominance hierarchical Bayesian optimization algorithm was combined with Shannon entropy of information theory to design and evaluate hydrometric networks. Specifically, the joint entropy from the combined networks was maximized to provide the most information, and the total correlation was minimized to reduce redundant information. To further optimize the efficiency between the networks, they were designed by maximizing the conditional entropy of the streamflow network given the information of the precipitation network. Compared to the traditional individual variable design approach, the integrated multivariable design method was able to determine more efficient optimal networks by avoiding the redundant stations. Additionally, four quantization cases were compared to evaluate their effects on the entropy calculations and the determination of the optimal networks. The evaluation results indicate that the quantization methods should be selected after careful consideration for each design problem since the station rankings and the optimal networks can change accordingly.

  14. Hybrid neural network model for the design of beam subjected to ...

    Indian Academy of Sciences (India)

    Design of beam; hybridization; genetic algorithms; neural networks. ... A hybrid neural network model which combines the features of feed forward neural networks and genetic algorithms has been developed for the design of beam ... Department of Civil Engineering, J.N.T.U College of Engineering, Anantapur 515 002 ...

  15. Effects of an acute and a sub-chronic 900 MHz GSM exposure on brain activity and behaviors of rats

    International Nuclear Information System (INIS)

    Elsa Brillaud; Aleksandra Piotrowski; Anthony Lecomte; Franck Robidel; Rene de Seze

    2006-01-01

    Radio frequencies are suspected to produce health effects. Concerning the mobile phone technology, according to position during use (close to the head), possible effects of radio frequencies on the central nervous system have to be evaluated. Previous works showed contradictory results, possibly due to experimental design diversity. In the framework of R.A.M.P. 2001 project, we evaluated possible effect of a 900 MHz GSM exposure on the central nervous system of rat at a structural, a functional and a behavioral level after acute or sub-chronic exposures. Rats were exposed using a loop antenna system to different S.A.R. levels and durations, according to results of the French C.O.M.O.B.I.O. 2001 project. A functional effect was found (modification of the cerebral activity and increase of the glia surface) after an acute exposure, even at a low level of brain averaged S.A.R. (1.5 W/kg). No cumulative effect was observed after a sub-chronic exposure (same amplitude of the effect). No structural or behavioral consequence was noted. We do not conclude on the neurotoxicity of the 900 MHz GSM exposure on the rat brain. Our results do not indicate any health risk. (authors)

  16. Effects of an acute and a sub-chronic 900 MHz GSM exposure on brain activity and behaviors of rats

    Energy Technology Data Exchange (ETDEWEB)

    Elsa Brillaud; Aleksandra Piotrowski; Anthony Lecomte; Franck Robidel; Rene de Seze [Toxicology Unit, INERIS, Verneuil en Halatte (France)

    2006-07-01

    Radio frequencies are suspected to produce health effects. Concerning the mobile phone technology, according to position during use (close to the head), possible effects of radio frequencies on the central nervous system have to be evaluated. Previous works showed contradictory results, possibly due to experimental design diversity. In the framework of R.A.M.P. 2001 project, we evaluated possible effect of a 900 MHz GSM exposure on the central nervous system of rat at a structural, a functional and a behavioral level after acute or sub-chronic exposures. Rats were exposed using a loop antenna system to different S.A.R. levels and durations, according to results of the French C.O.M.O.B.I.O. 2001 project. A functional effect was found (modification of the cerebral activity and increase of the glia surface) after an acute exposure, even at a low level of brain averaged S.A.R. (1.5 W/kg). No cumulative effect was observed after a sub-chronic exposure (same amplitude of the effect). No structural or behavioral consequence was noted. We do not conclude on the neurotoxicity of the 900 MHz GSM exposure on the rat brain. Our results do not indicate any health risk. (authors)

  17. The time constrained multi-commodity network flow problem and its application to liner shipping network design

    DEFF Research Database (Denmark)

    Karsten, Christian Vad; Pisinger, David; Røpke, Stefan

    2015-01-01

    The multi-commodity network flow problem is an important sub-problem in several heuristics and exact methods for designing route networks for container ships. The sub-problem decides how cargoes should be transported through the network provided by shipping routes. This paper studies the multi......-commodity network flow problem with transit time constraints which puts limits on the duration of the transit of the commodities through the network. It is shown that for the particular application it does not increase the solution time to include the transit time constraints and that including the transit time...

  18. Physical Layer Design in Wireless Sensor Networks for Fading Mitigation

    Directory of Open Access Journals (Sweden)

    Nuo Chen

    2013-09-01

    Full Text Available This paper presents the theoretical analysis, simulation results and suggests design in digital technology of a physical layer for wireless sensor networks. The proposed design is able to mitigate fading inside communication channel. To mitigate fading the chip interleaving technique is proposed. For the proposed theoretical model of physical layer, a rigorous mathematical analysis is conducted, where all signals are presented and processed in discrete time domain form which is suitable for further direct processing necessary for devices design in digital technology. Three different channels are used to investigate characteristics of the physical layer: additive white Gaussian noise channel (AWGN, AWG noise and flat fading channel and AWG noise and flat fading channel with interleaver and deinterleaver blocks in the receiver and transmitter respectively. Firstly, the mathematical model of communication system representing physical layer is developed based on the discrete time domain signal representation and processing. In the existing theory, these signals and their processing are represented in continuous time form, which is not suitable for direct implementation in digital technology. Secondly, the expressions for the probability of chip, symbol and bit error are derived. Thirdly, the communication system simulators are developed in MATLAB. The simulation results confirmed theoretical findings.

  19. Self-assembled three dimensional network designs for soft electronics.

    Science.gov (United States)

    Jang, Kyung-In; Li, Kan; Chung, Ha Uk; Xu, Sheng; Jung, Han Na; Yang, Yiyuan; Kwak, Jean Won; Jung, Han Hee; Song, Juwon; Yang, Ce; Wang, Ao; Liu, Zhuangjian; Lee, Jong Yoon; Kim, Bong Hoon; Kim, Jae-Hwan; Lee, Jungyup; Yu, Yongjoon; Kim, Bum Jun; Jang, Hokyung; Yu, Ki Jun; Kim, Jeonghyun; Lee, Jung Woo; Jeong, Jae-Woong; Song, Young Min; Huang, Yonggang; Zhang, Yihui; Rogers, John A

    2017-06-21

    Low modulus, compliant systems of sensors, circuits and radios designed to intimately interface with the soft tissues of the human body are of growing interest, due to their emerging applications in continuous, clinical-quality health monitors and advanced, bioelectronic therapeutics. Although recent research establishes various materials and mechanics concepts for such technologies, all existing approaches involve simple, two-dimensional (2D) layouts in the constituent micro-components and interconnects. Here we introduce concepts in three-dimensional (3D) architectures that bypass important engineering constraints and performance limitations set by traditional, 2D designs. Specifically, open-mesh, 3D interconnect networks of helical microcoils formed by deterministic compressive buckling establish the basis for systems that can offer exceptional low modulus, elastic mechanics, in compact geometries, with active components and sophisticated levels of functionality. Coupled mechanical and electrical design approaches enable layout optimization, assembly processes and encapsulation schemes to yield 3D configurations that satisfy requirements in demanding, complex systems, such as wireless, skin-compatible electronic sensors.

  20. Self-assembled three dimensional network designs for soft electronics

    Science.gov (United States)

    Jang, Kyung-In; Li, Kan; Chung, Ha Uk; Xu, Sheng; Jung, Han Na; Yang, Yiyuan; Kwak, Jean Won; Jung, Han Hee; Song, Juwon; Yang, Ce; Wang, Ao; Liu, Zhuangjian; Lee, Jong Yoon; Kim, Bong Hoon; Kim, Jae-Hwan; Lee, Jungyup; Yu, Yongjoon; Kim, Bum Jun; Jang, Hokyung; Yu, Ki Jun; Kim, Jeonghyun; Lee, Jung Woo; Jeong, Jae-Woong; Song, Young Min; Huang, Yonggang; Zhang, Yihui; Rogers, John A.

    2017-06-01

    Low modulus, compliant systems of sensors, circuits and radios designed to intimately interface with the soft tissues of the human body are of growing interest, due to their emerging applications in continuous, clinical-quality health monitors and advanced, bioelectronic therapeutics. Although recent research establishes various materials and mechanics concepts for such technologies, all existing approaches involve simple, two-dimensional (2D) layouts in the constituent micro-components and interconnects. Here we introduce concepts in three-dimensional (3D) architectures that bypass important engineering constraints and performance limitations set by traditional, 2D designs. Specifically, open-mesh, 3D interconnect networks of helical microcoils formed by deterministic compressive buckling establish the basis for systems that can offer exceptional low modulus, elastic mechanics, in compact geometries, with active components and sophisticated levels of functionality. Coupled mechanical and electrical design approaches enable layout optimization, assembly processes and encapsulation schemes to yield 3D configurations that satisfy requirements in demanding, complex systems, such as wireless, skin-compatible electronic sensors.

  1. Portable ECG design and application based on wireless sensor network

    Directory of Open Access Journals (Sweden)

    Gül Fatma TÜRKER

    2016-05-01

    Full Text Available In this study, in order to follow the heart signals of patients that needs to be monitored instantly and continuously without mobility restrictions, a portable electrocardiogram circuit is designed. After performing the detection, upgrading, cleaning and digitizing of ECG signal received from patient via disposable electrodes, ECG signals was performed that transmit to a central node with Wireless Sensor Network (WSN based on ZigBee 802.11.4 standard. Central node is connected to the serial port of a computer. Received data from the central node is processed on computer and continuous flow graph is obtained. The obligation to use wires for tracing patients’ ECG has been removed with this portable system. As it can be seen in this study, thanks to WSN’s property of forming network by itself and its augmentable loop property, the restrain of ECG signals to reach far away distances can be surmounted. The transmission of biological signals with WSN will light on many studies that follow of patients from a distance.

  2. An Optimal Method to Design Wireless Sensor Network Structures

    Directory of Open Access Journals (Sweden)

    Yang Ling

    2018-01-01

    Full Text Available In order to optimize the structure of wireless sensor network, an improved wireless sensor network sleep mechanism is proposed. First, some nodes in the area with too high redundancy are dormant by density control, so that the active nodes are even more distributed. Then, the active node is subjected to circular coverage redundancy decision. Different circumferential coverage decision methods are used for network boundary nodes and non-boundary nodes. As a result, the boundary nodes and non-boundary nodes are well dormant, and the network redundancy is reduced. The simulation results show that the improved dormancy mechanism makes the number of active nodes in the network smaller and more evenly, and the network lifetime is extended on the basis of maintaining the original coverage of the network. Therefore, the proposed method can achieve optimal coverage in wireless sensor networks. The network prolongs network lifetime while ensuring reliable monitoring performance.

  3. Design of an adaptive neural network based power system stabilizer.

    Science.gov (United States)

    Liu, Wenxin; Venayagamoorthy, Ganesh K; Wunsch, Donald C

    2003-01-01

    Power system stabilizers (PSS) are used to generate supplementary control signals for the excitation system in order to damp the low frequency power system oscillations. To overcome the drawbacks of conventional PSS (CPSS), numerous techniques have been proposed in the literature. Based on the analysis of existing techniques, this paper presents an indirect adaptive neural network based power system stabilizer (IDNC) design. The proposed IDNC consists of a neuro-controller, which is used to generate a supplementary control signal to the excitation system, and a neuro-identifier, which is used to model the dynamics of the power system and to adapt the neuro-controller parameters. The proposed method has the features of a simple structure, adaptivity and fast response. The proposed IDNC is evaluated on a single machine infinite bus power system under different operating conditions and disturbances to demonstrate its effectiveness and robustness.

  4. Design of verification platform for wireless vision sensor networks

    Science.gov (United States)

    Ye, Juanjuan; Shang, Fei; Yu, Chuang

    2017-08-01

    At present, the majority of research for wireless vision sensor networks (WVSNs) still remains in the software simulation stage, and the verification platforms of WVSNs that available for use are very few. This situation seriously restricts the transformation from theory research of WVSNs to practical application. Therefore, it is necessary to study the construction of verification platform of WVSNs. This paper combines wireless transceiver module, visual information acquisition module and power acquisition module, designs a high-performance wireless vision sensor node whose core is ARM11 microprocessor and selects AODV as the routing protocol to set up a verification platform called AdvanWorks for WVSNs. Experiments show that the AdvanWorks can successfully achieve functions of image acquisition, coding, wireless transmission, and obtain the effective distance parameters between nodes, which lays a good foundation for the follow-up application of WVSNs.

  5. Network-Cognizant Design of Decentralized Volt/VAR Controllers

    Energy Technology Data Exchange (ETDEWEB)

    Baker, Kyri A [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Bernstein, Andrey [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Zhao, Changhong [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Dall-Anese, Emiliano [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

    2017-10-03

    This paper considers the problem of designing decentralized Volt/VAR controllers for distributed energy resources (DERs). The voltage-reactive power characteristics of individual DERs are obtained by solving a convex optimization problem, where given performance objectives (e.g., minimization of the voltage deviations from a given profile) are specified and stability constraints are enforced. The resultant Volt/VAR characteristics are network-cognizant, in the sense that they embed information on the location of the DERs and, consequently, on the effect of reactive-power adjustments on the voltages throughout the feeder. Bounds on the maximum voltage deviation incurred by the controllers are analytically established. Numerical results are reported to corroborate the technical findings.

  6. PV-Diesel Hybrid SCADA Experiment Network Design

    Science.gov (United States)

    Kalu, Alex; Durand, S.; Emrich, Carol; Ventre, G.; Wilson, W.; Acosta, R.

    1999-01-01

    The essential features of an experimental network for renewable power system satellite based supervisory, control and data acquisition (SCADA) are communication links, controllers, diagnostic equipment and a hybrid power system. Required components for implementing the network consist of two satellite ground stations, to satellite modems, two 486 PCs, two telephone receivers, two telephone modems, two analog telephone lines, one digital telephone line, a hybrid-power system equipped with controller and a satellite spacecraft. In the technology verification experiment (TVE) conducted by Savannah State University and Florida Solar Energy Center, the renewable energy hybrid system is the Apex-1000 Mini-Hybrid which is equipped with NGC3188 for user interface and remote control and the NGC2010 for monitoring and basic control tasks. This power system is connected to a satellite modem via a smart interface, RS232. Commands are sent to the power system control unit through a control PC designed as PC1. PC1 is thus connected to a satellite model through RS232. A second PC, designated PC2, the diagnostic PC is connected to both satellite modems via separate analog telephone lines for checking modems'health. PC2 is also connected to PC1 via a telephone line. Due to the unavailability of a second ground station for the ACTS, one ground station is used to serve both the sending and receiving functions in this experiment. Signal is sent from the control PC to the Hybrid system at a frequency f(sub 1), different from f(sub 2), the signal from the hybrid system to the control PC. f(sub l) and f(sub 2) are sufficiently separated to avoid interference.

  7. Genetic Algorithm for Multiuser Discrete Network Design Problem under Demand Uncertainty

    Directory of Open Access Journals (Sweden)

    Wu Juan

    2012-01-01

    Full Text Available Discrete network design is an important part of urban transportation planning. The purpose of this paper is to present a bilevel model for discrete network design. The upper-level model aims to minimize the total travel time under a stochastic demand to design a discrete network. In the lower-level model, demands are assigned to the network through a multiuser traffic equilibrium assignment. Generally, discrete network could affect path selections of demands, while the results of the multiuser traffic equilibrium assignment need to reconstruct a new discrete network. An iterative approach including an improved genetic algorithm and Frank-Wolfe algorithm is used to solve the bi-level model. The numerical results on Nguyen Dupuis network show that the model and the related algorithms were effective for discrete network design.

  8. Low-cost design of next generation SONET/SDH networks with multiple constraints

    CSIR Research Space (South Africa)

    Karem, TR

    2007-07-01

    Full Text Available on constraints programming satisfaction technology is proposed. The algorithm is tested in OPNET simulation environment using different network models derived from a hypothetical case study of an optical network design for Bellville area in Cape Town, South...

  9. Multiobjecitve Sampling Design for Calibration of Water Distribution Network Model Using Genetic Algorithm and Neural Network

    Directory of Open Access Journals (Sweden)

    Kourosh Behzadian

    2008-03-01

    Full Text Available In this paper, a novel multiobjective optimization model is presented for selecting optimal locations in the water distribution network (WDN with the aim of installing pressure loggers. The pressure data collected at optimal locations will be used later on in the calibration of the proposed WDN model. Objective functions consist of maximization of calibrated model prediction accuracy and minimization of the total cost for sampling design. In order to decrease the model run time, an optimization model has been developed using multiobjective genetic algorithm and adaptive neural network (MOGA-ANN. Neural networks (NNs are initially trained after a number of initial GA generations and periodically retrained and updated after generation of a specified number of full model-analyzed solutions. Trained NNs are replaced with the fitness evaluation of some chromosomes within the GA progress. Using cache prevents objective function evaluation of repetitive chromosomes within GA. Optimal solutions are obtained through pareto-optimal front with respect to the two objective functions. Results show that jointing NNs in MOGA for approximating portions of chromosomes’ fitness in each generation leads to considerable savings in model run time and can be promising for reducing run-time in optimization models with significant computational effort.

  10. Tsunameter Network Design for the U.S. DART® Array

    Science.gov (United States)

    Spillane, M. C.; Gica, E.; Titov, V. V.

    2009-12-01

    Underlying the success in real-time usage of NOAA’s Tsunami Forecast System, during several mild events in the years since the Indian Ocean catastrophe, are the network of bottom pressure sensors that detect tsunami wave trains, and a pre-computed set of propagation solutions that can be linearly combined to synthesize them. The U.S. portion of the network, a subset of which pre-dated December 2004, has been greatly expanded and, together with units deployed by international partners, provides comprehensive coverage of the Pacific and Atlantic, and partial coverage in the Indian Ocean. The data from the array are freely distributed. Other nations have deployed or are developing tsunameters that will improve global coverage and enhance forecast and warning capabilities. In the case of the U.S. network, the siting choices were based on an initial workshop, to identify the primary threat areas and allocate the available instruments, followed by a gathering of relevant environmental, engineering, and propagation data to identify the optimal locations. In addition to its vital role in the forecast system itself, the propagation database was invaluable in the DART® site selection process by quantifying the complex patterns of tsunami amplitude and timing. A major benefit, in practice, of tsunami detection and forecasting operations is the reliable issuance of early warning cancellations, that can save the expense and loss of public confidence associated with false alarms; this requires that weak signals are detectable at the closest DART® locations. Signal to noise considerations also factor into uncertainty estimates in source characterization and the forecast products that result. While the initial deployment of the U.S. network was completed in March 2008, the array is not static. Rather it is expected that it will evolve (and hopefully expand) as experience is gained on locations where maintaining instruments is difficult due to vandalism or severe environments

  11. A lightweight security scheme for wireless body area networks: design, energy evaluation and proposed microprocessor design.

    Science.gov (United States)

    Selimis, Georgios; Huang, Li; Massé, Fabien; Tsekoura, Ioanna; Ashouei, Maryam; Catthoor, Francky; Huisken, Jos; Stuyt, Jan; Dolmans, Guido; Penders, Julien; De Groot, Harmke

    2011-10-01

    In order for wireless body area networks to meet widespread adoption, a number of security implications must be explored to promote and maintain fundamental medical ethical principles and social expectations. As a result, integration of security functionality to sensor nodes is required. Integrating security functionality to a wireless sensor node increases the size of the stored software program in program memory, the required time that the sensor's microprocessor needs to process the data and the wireless network traffic which is exchanged among sensors. This security overhead has dominant impact on the energy dissipation which is strongly related to the lifetime of the sensor, a critical aspect in wireless sensor network (WSN) technology. Strict definition of the security functionality, complete hardware model (microprocessor and radio), WBAN topology and the structure of the medium access control (MAC) frame are required for an accurate estimation of the energy that security introduces into the WBAN. In this work, we define a lightweight security scheme for WBAN, we estimate the additional energy consumption that the security scheme introduces to WBAN based on commercial available off-the-shelf hardware components (microprocessor and radio), the network topology and the MAC frame. Furthermore, we propose a new microcontroller design in order to reduce the energy consumption of the system. Experimental results and comparisons with other works are given.

  12. The Measurement of Low Frequency Magnetic Field of Two Kinds of GSM900 Mobile Phone

    Directory of Open Access Journals (Sweden)

    Mehri Kaviani Moghadam

    2008-06-01

    Full Text Available Introduction:  The  use  of  mobile  communication  systems  has  dramatically  increased  over  the  past  decade. Although many studies have been performed to determine the effect of radio frequency (RF but  less attention has been paid to the possible biological impact of exposure to extremely low frequency  (ELF components.   The objective of this study is two folds. One is to design the equipments needed for the measurement of  the ELF fields of two types of GSM900 mobile phone. Secondly, use a protocol suitable for an accurate  assessment of the ELF fields.  Materials  and Methods:  First  a  home-made  search  coil  was  provided  and  calibrated precisely  under  several experiments. Using Fast Fourier Transform, the power spectrum density of the induced voltage in  the search coil was analyzed and the amplitudes of 217 Hz and its harmonics were extracted and then the  distribution of magnetic field in the back side of mobile phones was determined.  Results: The values of B-field on the back side of the two kinds of GSM mobile phone were different.  They  were  between  50  to  160  µT in  Nokia  3310  and  14  to  30  µT in  Nokia  8310.  Considering  the  difference between the amplitudes of frequency components at 217 Hz and its harmonics in the two kinds  of mobile phone, a range of magnetic flux density at different times in a five day period was measured.  Discussion and Conclusion: These findings emphasize the need for considering the distribution of low  frequency magnetic field from mobile phone when biological effects of magnetic fields are studied. To  determine  the  intensity  windowing  effect,  one  must  consider  the  physical  characteristics  of  the  fundamental  frequency  component  wave  (217  Hz  and  its  harmonics  produced  by  the  mobile  phone  similar to the one generated under a real situation.

  13. On optimal designs of transparent WDM networks with 1 + 1 protection leveraged by all-optical XOR network coding schemes

    Science.gov (United States)

    Dao, Thanh Hai

    2018-01-01

    Network coding techniques are seen as the new dimension to improve the network performances thanks to the capability of utilizing network resources more efficiently. Indeed, the application of network coding to the realm of failure recovery in optical networks has been marking a major departure from traditional protection schemes as it could potentially achieve both rapid recovery and capacity improvement, challenging the prevailing wisdom of trading capacity efficiency for speed recovery and vice versa. In this context, the maturing of all-optical XOR technologies appears as a good match to the necessity of a more efficient protection in transparent optical networks. In addressing this opportunity, we propose to use a practical all-optical XOR network coding to leverage the conventional 1 + 1 optical path protection in transparent WDM optical networks. The network coding-assisted protection solution combines protection flows of two demands sharing the same destination node in supportive conditions, paving the way for reducing the backup capacity. A novel mathematical model taking into account the operation of new protection scheme for optimal network designs is formulated as the integer linear programming. Numerical results based on extensive simulations on realistic topologies, COST239 and NSFNET networks, are presented to highlight the benefits of our proposal compared to the conventional approach in terms of wavelength resources efficiency and network throughput.

  14. On the Design of Energy Efficient Optical Networks with Software Defined Networking Control Across Core and Access Networks

    DEFF Research Database (Denmark)

    Wang, Jiayuan; Yan, Ying; Dittmann, Lars

    2013-01-01

    This paper presents a Software Defined Networking (SDN) control plane based on an overlay GMPLS control model. The SDN control platform manages optical core networks (WDM/DWDM networks) and the associated access networks (GPON networks), which makes it possible to gather global information...

  15. Optimal experiment design for model selection in biochemical networks.

    Science.gov (United States)

    Vanlier, Joep; Tiemann, Christian A; Hilbers, Peter A J; van Riel, Natal A W

    2014-02-20

    Mathematical modeling is often used to formalize hypotheses on how a biochemical network operates by discriminating between competing models. Bayesian model selection offers a way to determine the amount of evidence that data provides to support one model over the other while favoring simple models. In practice, the amount of experimental data is often insufficient to make a clear distinction between competing models. Often one would like to perform a new experiment which would discriminate between competing hypotheses. We developed a novel method to perform Optimal Experiment Design to predict which experiments would most effectively allow model selection. A Bayesian approach is applied to infer model parameter distributions. These distributions are sampled and used to simulate from multivariate predictive densities. The method is based on a k-Nearest Neighbor estimate of the Jensen Shannon divergence between the multivariate predictive densities of competing models. We show that the method successfully uses predictive differences to enable model selection by applying it to several test cases. Because the design criterion is based on predictive distributions, which can be computed for a wide range of model quantities, the approach is very flexible. The method reveals specific combinations of experiments which improve discriminability even in cases where data is scarce. The proposed approach can be used in conjunction with existing Bayesian methodologies where (approximate) posteriors have been determined, making use of relations that exist within the inferred posteriors.

  16. Design The Cervical Cancer Detector Use The Artificial Neural Network

    Science.gov (United States)

    Intan Af'idah, Dwi; Didik Widianto, Eko; Setyawan, Budi

    2013-06-01

    Cancer is one of the contagious diseases that become a public health issue, both in the world and in Indonesia. In the world, 12% of all deaths caused by cancer and is the second killer after cardiovascular disease. Early detection using the IVA is a practical and inexpensive (only requiring acetic acid). However, the accuracy of the method is quite low, as it can not detect the stage of the cancer. While other methods have a better sensitivity than the IVA method, is a method of PAP smear. However, this method is relatively expensive, and requires an experienced pathologist-cytologist. According to the case above, Considered important to make the cancer cervics detector that is used to detect the abnormality and cervical cancer stage and consists of a digital microscope, as well as a computer application based on artificial neural network. The use of cervical cancer detector software and hardware are integrated each other. After the specifications met, the steps to design the cervical cancer detection are: Modifying a conventional microscope by adding a lens, image recording, and the lights, Programming the tools, designing computer applications, Programming features abnormality detection and staging of cancer.

  17. Surge currents and voltages at the low voltage power mains during lightning strike to a GSM tower

    Energy Technology Data Exchange (ETDEWEB)

    Markowska, Renata [Bialystok Technical University (Poland)], E-mail: remark@pb.edu.pl

    2007-07-01

    The paper presents the results of numerical calculations of lightning surge currents and voltages in the low voltage power mains system connected to a free standing GSM base station. Direct lightning strike to GSM tower was studied. The analysis concerned the current that flows to the transformer station through AC power mains, the potential difference between the grounding systems of the GSM and the transformer stations and the voltage differences between phase and PE conductors of the power mains underground cable at both the GSM and the transformer sides. The calculations were performed using a numerical program based on the electromagnetic field theory and the method of moments. (author)

  18. A memetic algorithm for bi-objective integrated forward/reverse logistics network design

    NARCIS (Netherlands)

    Pishvaee, Mir Saman; Farahani, Reza Zanjirani; Dullaert, Wout

    Logistics network design is a major strategic issue due to its impact on the efficiency and responsiveness of the supply chain. This paper proposes a model for integrated logistics network design to avoid the sub-optimality caused by a separate, sequential design of forward and reverse logistics

  19. Harris Simulator Design Description for Adaptive Distributed Network Management System

    National Research Council Canada - National Science Library

    1986-01-01

    ... (ADNMS), Naval Research Laboratory (NRL). The document describes the Harris Simulator used to support the development and test of a first generation network management algorithm for a typical SDI communications network...

  20. The design of a network emulation and simulation laboratory

    CSIR Research Space (South Africa)

    Von Solms, S

    2015-07-01

    Full Text Available The development of the Network Emulation and Simulation Laboratory is motivated by the drive to contribute to the enhancement of the security and resilience of South Africa's critical information infrastructure. The goal of the Network Emulation...

  1. Design Concepts for a Global Telemetered Seismograph Network

    Science.gov (United States)

    Peterson, Jon; Orsini, Nicholas A.

    1982-01-01

    INTRODUCTION This study represents a first step in developing an integrated, real-tlme global seismic data acquisition system -- a Global Telemetered Seismograph Network (GTSN). The principal objective of the GTSN will be to acquire reliable, high-quality, real-time seismic data for rapid location and analysis of seismic events. A secondary, but important, objective of the GTSN is to augment the existing off-line seismic data base available for research. The deployment of the GTSN will involve a variety of interrelated activities -- development of the data acquisition and receiving equipment, establishment of satellite and terrestrial communication links, site selection and preparation, training of station personnel, equipment installation, and establishment of support facilities. It is a complex program and the develop- ment of a sound management plan will be essential. The purpose of this study is not to fix design goals or dictate avenues of approach but to develop work- ing concepts that may be used as a framework for program planning. The international exchange of seismic data has been an important factor in the progress that has been made during the past two decades in our under- standing of earthquakes and global tectonics. The seismic data base available for analysis and research is derived principally from the Global Seismograph Network (GSN), which is funded and managed by the U.S. Geological Survey (USGS). The GSN comprises some 120 seismograph stations located in more than 60 countries of the world. Established during the 1960's with the installation of the World-Wide Standardized Seismograph Network (WWSSN), the GSN has been augmented in recent years by the installation of more advanced data systems, such as the Seismic Research Observatories (SRO), the modified High-Gain Long- Period (ASRO) seismographs, and the digital WWSSN (DWWSSN). The SRO, ASRO, and DWWSSN stations have the common, distinctive feature of digital data recording, so they are known

  2. Virtualized Network Infrastructures: Performance Analysis, Design and Implementation

    OpenAIRE

    Contoli, Chiara

    2017-01-01

    In recent decades, there has been a tremendous evolution in the traffic on the Internet and enterprises networks. Networks assisted since the beginning to two phenomena: on the one hand, the birth of a multitude of applications, each posing different requirements; on the other hand, the explosion of personal mobile networking, with an ever increasing demand of devices that require connectivity. These trends resulted in increased network complexity, leading to difficult management and high cos...

  3. Risk-Aware Design of Value and Coordination Networks

    NARCIS (Netherlands)

    Fatemi, Hassan

    2012-01-01

    A collaborative network is a network consisting of a set of autonomous actors (e.g. enterprizes, organizations and people) that collaborate to achieve common or compatible goals. In a collaborative network each enterprize contributes with its own specific products or services to satisfy the consumer

  4. Environmental Design for a Structured Network Learning Society

    Science.gov (United States)

    Chang, Ben; Cheng, Nien-Heng; Deng, Yi-Chan; Chan, Tak-Wai

    2007-01-01

    Social interactions profoundly impact the learning processes of learners in traditional societies. The rapid rise of the Internet using population has been the establishment of numerous different styles of network communities. Network societies form when more Internet communities are established, but the basic form of a network society, especially…

  5. Wi-Fi Network Communication Technology Design | Onibere ...

    African Journals Online (AJOL)

    Transmission media (like Satellite, VSAT), access method used to transmit both voice and data on the networks and underlying software and hardware requirements. Also the various standards and protocol for proper wireless networks management, the various authentication and encryption techniques of Wi -Fi network ...

  6. On the Design of Energy Efficient Optical Networks with Software Defined Networking Control Across Core and Access Networks

    DEFF Research Database (Denmark)

    Wang, Jiayuan; Yan, Ying; Dittmann, Lars

    2013-01-01

    This paper presents a Software Defined Networking (SDN) control plane based on an overlay GMPLS control model. The SDN control platform manages optical core networks (WDM/DWDM networks) and the associated access networks (GPON networks), which makes it possible to gather global information...... and enable wider areas' energy efficiency networking. The energy related information of the networks and the types of the traffic flows are collected and utilized for the end-to-end QoS provision. Dynamic network simulation results show that by applying different routing algorithms according to the type...

  7. Radial basis function (RBF) neural network control for mechanical systems design, analysis and Matlab simulation

    CERN Document Server

    Liu, Jinkun

    2013-01-01

    Radial Basis Function (RBF) Neural Network Control for Mechanical Systems is motivated by the need for systematic design approaches to stable adaptive control system design using neural network approximation-based techniques. The main objectives of the book are to introduce the concrete design methods and MATLAB simulation of stable adaptive RBF neural control strategies. In this book, a broad range of implementable neural network control design methods for mechanical systems are presented, such as robot manipulators, inverted pendulums, single link flexible joint robots, motors, etc. Advanced neural network controller design methods and their stability analysis are explored. The book provides readers with the fundamentals of neural network control system design.   This book is intended for the researchers in the fields of neural adaptive control, mechanical systems, Matlab simulation, engineering design, robotics and automation. Jinkun Liu is a professor at Beijing University of Aeronautics and Astronauti...

  8. Are there evidences for the influence of GSM- and TETRA-electromagnetic fields on language comprehension in the human memory?; Laesst sich durch den Einfluss von kopfnah gepulsten Hochfrequenzfeldern des GSM- und TETRA-Mobilfunks ein Wirkungseffekt auf sprachverarbeitende Prozesse im Gedaechtnis nachweisen?

    Energy Technology Data Exchange (ETDEWEB)

    Kaul, G. [Bundesanstalt fuer Arbeitsschutz und Arbeitsmedizin, Berlin (Germany); Stummvoll, B.; Beyer, R. [Humboldt-Universitaet, Berlin (Germany). Institut fuer Psychologie

    2004-07-01

    The experimental study using a double blind design examining the influences of the electromagnetic fields of GSM and TETRA mobile phones on the language comprehension in the human memory. 30 young men had to decide whether a given word was contained in a text they had read before. It will be demonstrated that GSM-radiation seemed to cause a quicker answer. In contrast the TETRA-radiation allowed reading - i.e. to understand - the text in a significant shorter time when the exposition came from the telephone situated on the right side of the head. Since these effects are very small, there is now evidence for a health risk. Both results point at a support of the mental processes at attention and memory. (orig.)

  9. Designing neural networks that process mean values of random variables

    Energy Technology Data Exchange (ETDEWEB)

    Barber, Michael J. [AIT Austrian Institute of Technology, Innovation Systems Department, 1220 Vienna (Austria); Clark, John W. [Department of Physics and McDonnell Center for the Space Sciences, Washington University, St. Louis, MO 63130 (United States); Centro de Ciências Matemáticas, Universidade de Madeira, 9000-390 Funchal (Portugal)

    2014-06-13

    We develop a class of neural networks derived from probabilistic models posed in the form of Bayesian networks. Making biologically and technically plausible assumptions about the nature of the probabilistic models to be represented in the networks, we derive neural networks exhibiting standard dynamics that require no training to determine the synaptic weights, that perform accurate calculation of the mean values of the relevant random variables, that can pool multiple sources of evidence, and that deal appropriately with ambivalent, inconsistent, or contradictory evidence. - Highlights: • High-level neural computations are specified by Bayesian belief networks of random variables. • Probability densities of random variables are encoded in activities of populations of neurons. • Top-down algorithm generates specific neural network implementation of given computation. • Resulting “neural belief networks” process mean values of random variables. • Such networks pool multiple sources of evidence and deal properly with inconsistent evidence.

  10. Designed a web crawler which oriented network public opinion data acquisition

    Science.gov (United States)

    Lu, Shan; Ma, Hui; Gao, Ying

    2015-12-01

    The paper describes the meaning of network public opinion and the network public opinion research of data acquisition technique. Designed and implemented a web crawler which oriented network public opinion data acquisition. Insufficient analysis of the generic web crawler, using asynchronous Socket, DNS cache, and queue downloads to improve its bottom story frame, increase the speed of collecting.

  11. A Multiperiod Supply Chain Network Design Considering Carbon Emissions

    Directory of Open Access Journals (Sweden)

    Yang Peng

    2016-01-01

    Full Text Available This paper introduces a mixed integer linear programming formulation for modeling and solving a multiperiod one-stage supply chain distribution network design problem. The model is aimed to minimize two objectives, the total supply chain cost and the greenhouse gas emissions generated mainly by transportation and warehousing operations. The demand forecast is known for the planning horizon and shortage of demand is allowed at a penalty cost. This scenario must satisfy a minimum service level. Two carbon emission regulatory policies are investigated, the tax or carbon credit and the carbon emission cap. Computational experiments are performed to analyze the trade-offs between the total cost of the supply chain, the carbon emission quantity, and both carbon emission regulatory policies. Results demonstrate that for a certain range the carbon credit price incentivizes the reduction of carbon emissions to the environment. On the other hand, modifying the carbon emission cap inside a certain range could lead to significant reductions of carbon emission while not significantly compromising the total cost of the supply chain.

  12. Designing reliable supply chain network with disruption risk

    Directory of Open Access Journals (Sweden)

    Ali Bozorgi Amiri

    2013-01-01

    Full Text Available Although supply chains disruptions rarely occur, their negative effects are prolonged and severe. In this paper, we propose a reliable capacitated supply chain network design (RSCND model by considering random disruptions in both distribution centers and suppliers. The proposed model determines the optimal location of distribution centers (DC with the highest reliability, the best plan to assign customers to opened DCs and assigns opened DCs to suitable suppliers with lowest transportation cost. In this study, random disruption occurs at the location, capacity of the distribution centers (DCs and suppliers. It is assumed that a disrupted DC and a disrupted supplier may lose a portion of their capacities, and the rest of the disrupted DC's demand can be supplied by other DCs. In addition, we consider shortage in DCs, which can occur in either normal or disruption conditions and DCs, can support each other in such circumstances. Unlike other studies in the extent of literature, we use new approach to model the reliability of DCs; we consider a range of reliability instead of using binary variables. In order to solve the proposed model for real-world instances, a Non-dominated Sorting Genetic Algorithm-II (NSGA-II is applied. Preliminary results of testing the proposed model of this paper on several problems with different sizes provide seem to be promising.

  13. An expanded genome-scale model of Escherichia coli K-12 (iJR904 GSM/GPR).

    Science.gov (United States)

    Reed, Jennifer L; Vo, Thuy D; Schilling, Christophe H; Palsson, Bernhard O

    2003-01-01

    Diverse datasets, including genomic, transcriptomic, proteomic and metabolomic data, are becoming readily available for specific organisms. There is currently a need to integrate these datasets within an in silico modeling framework. Constraint-based models of Escherichia coli K-12 MG1655 have been developed and used to study the bacterium's metabolism and phenotypic behavior. The most comprehensive E. coli model to date (E. coli iJE660a GSM) accounts for 660 genes and includes 627 unique biochemical reactions. An expanded genome-scale metabolic model of E. coli (iJR904 GSM/GPR) has been reconstructed which includes 904 genes and 931 unique biochemical reactions. The reactions in the expanded model are both elementally and charge balanced. Network gap analysis led to putative assignments for 55 open reading frames (ORFs). Gene to protein to reaction associations (GPR) are now directly included in the model. Comparisons between predictions made by iJR904 and iJE660a models show that they are generally similar but differ under certain circumstances. Analysis of genome-scale proton balancing shows how the flux of protons into and out of the medium is important for maximizing cellular growth. E. coli iJR904 has improved capabilities over iJE660a. iJR904 is a more complete and chemically accurate description of E. coli metabolism than iJE660a. Perhaps most importantly, iJR904 can be used for analyzing and integrating the diverse datasets. iJR904 will help to outline the genotype-phenotype relationship for E. coli K-12, as it can account for genomic, transcriptomic, proteomic and fluxomic data simultaneously.

  14. Theory and design of broadband matching networks applied electricity and electronics

    CERN Document Server

    Chen, Wai-Kai

    1976-01-01

    Theory and Design of Broadband Matching Networks centers on the network theory and its applications to the design of broadband matching networks and amplifiers. Organized into five chapters, this book begins with a description of the foundation of network theory. Chapter 2 gives a fairly complete exposition of the scattering matrix associated with an n-port network. Chapter 3 considers the approximation problem along with a discussion of the approximating functions. Chapter 4 explains the Youla's theory of broadband matching by illustrating every phase of the theory with fully worked out examp

  15. Communications network design and costing model technical manual

    Science.gov (United States)

    Logan, K. P.; Somes, S. S.; Clark, C. A.

    1983-01-01

    This computer model provides the capability for analyzing long-haul trunking networks comprising a set of user-defined cities, traffic conditions, and tariff rates. Networks may consist of all terrestrial connectivity, all satellite connectivity, or a combination of terrestrial and satellite connectivity. Network solutions provide the least-cost routes between all cities, the least-cost network routing configuration, and terrestrial and satellite service cost totals. The CNDC model allows analyses involving three specific FCC-approved tariffs, which are uniquely structured and representative of most existing service connectivity and pricing philosophies. User-defined tariffs that can be variations of these three tariffs are accepted as input to the model and allow considerable flexibility in network problem specification. The resulting model extends the domain of network analysis from traditional fixed link cost (distance-sensitive) problems to more complex problems involving combinations of distance and traffic-sensitive tariffs.

  16. Food Web Designer: a flexible tool to visualize interaction networks

    OpenAIRE

    Sint, Daniela; Traugott, Michael

    2015-01-01

    Species are embedded in complex networks of ecological interactions and assessing these networks provides a powerful approach to understand what the consequences of these interactions are for ecosystem functioning and services. This is mandatory to develop and evaluate strategies for the management and control of pests. Graphical representations of networks can help recognize patterns that might be overlooked otherwise. However, there is a lack of software which allows visualizing these compl...

  17. eGSM: A extended Sky Model of Diffuse Radio Emission

    Science.gov (United States)

    Kim, Doyeon; Liu, Adrian; Switzer, Eric

    2018-01-01

    Both cosmic microwave background and 21cm cosmology observations must contend with astrophysical foreground contaminants in the form of diffuse radio emission. For precise cosmological measurements, these foregrounds must be accurately modeled over the entire sky Ideally, such full-sky models ought to be primarily motivated by observations. Yet in practice, these observations are limited, with data sets that are observed not only in a heterogenous fashion, but also over limited frequency ranges. Previously, the Global Sky Model (GSM) took some steps towards solving the problem of incomplete observational data by interpolating over multi-frequency maps using principal component analysis (PCA).In this poster, we present an extended version of GSM (called eGSM) that includes the following improvements: 1) better zero-level calibration 2) incorporation of non-uniform survey resolutions and sky coverage 3) the ability to quantify uncertainties in sky models 4) the ability to optimally select spectral models using Bayesian Evidence techniques.

  18. Design and analysis of a novel chaotic diagonal recurrent neural network

    Science.gov (United States)

    Wang, Libiao; Meng, Zhuo; Sun, Yize; Guo, Lei; Zhou, Mingxing

    2015-09-01

    A chaotic neural network model with logistic mapping is proposed to improve the performance of the conventional diagonal recurrent neural network. The network shows rich dynamic behaviors that contribute to escaping from a local minimum to reach the global minimum easily. Then, a simple parameter modulated chaos controller is adopted to enhance convergence speed of the network. Furthermore, an adaptive learning algorithm with the robust adaptive dead zone vector is designed to improve the generalization performance of the network, and weights convergence for the network with the adaptive dead zone vectors is proved in the sense of Lyapunov functions. Finally, the numerical simulation is carried out to demonstrate the correctness of the theory.

  19. Design Guidelines for Collaboration and Participation with Examples from the LN4LD (Learning Network for Learning Design)

    NARCIS (Netherlands)

    Burgos, Daniel; Hummel, Hans; Tattersall, Colin; Brouns, Francis; Koper, Rob

    2007-01-01

    Burgos, D., Hummel, H. G. K., Tattersall, C., Brouns, F., & Koper, R. (2009). Design Guidelines for Collaboration and Participation with Examples from the LN4LD (Learning Network for Learning Design). In L. Lockyer, S. Bennett, S. Agostinho & B. Harper (Eds.), Handbook of Research on Learning Design

  20. A Unified Framework for Analyzing and Designing for Stationary Arterial Networks

    Science.gov (United States)

    2017-05-17

    This research aims to develop a unified theoretical and simulation framework for analyzing and designing signals for stationary arterial networks. Existing traffic flow models used in design and analysis of signal control strategies are either too si...

  1. Model-based design of self-Adapting networked signal processing systems

    NARCIS (Netherlands)

    Oliveira Filho, J.A. de; Papp, Z.; Djapic, R.; Oostveen, J.C.

    2013-01-01

    The paper describes a model based approach for architecture design of runtime reconfigurable, large-scale, networked signal processing applications. A graph based modeling formalism is introduced to describe all relevant aspects of the design (functional, concurrency, hardware, communication,

  2. Nonlinear Maps for Design of Discrete Time Models of Neuronal Network Dynamics

    Science.gov (United States)

    2016-02-29

    network activity. D· 1S. SUBJECT TERMS Map-based neuronal model, Discrete time spiking dynamics, Synapses, Neurons , Neurobiological Networks 16...N00014-16-1-2252 Report #1 Performance/Technical Monthly Report Nonlinear Maps for Design of Discrete-Time Models of Neuronal Network Dynamics...Postdoc. The research plan assumes part-time involvement (50%) of a postdoc, which have experience with neuronal network simulations using standard

  3. Design of FPGA Based Neural Network Controller for Earth Station Power System

    OpenAIRE

    Hassen T. Dorrah; Ninet M. A. El-Rahman; Faten H. Fahmy; Hanaa T. El-Madany

    2012-01-01

    Automation of generating hardware description language code from neural networks models can highly decrease time of implementation those networks into a digital devices, thus significant money savings. To implement the neural network into hardware designer, it is required to translate generated model into device structure. VHDL language is used to describe those networks into hardware. VHDL code has been proposed to implement ANNs as well as to present simulation results with floating point a...

  4. A Novel Dual-Band Rectenna for Ambient RF Energy Harvesting at GSM 900 MHz and 1800 MHz

    Directory of Open Access Journals (Sweden)

    Dinh Khanh Ho

    2017-06-01

    Full Text Available This paper presents a novel dual-band rectenna for RF energy harvesting system. This rectenna is created from a dual-band antenna and a dual-band rectifier which operates at GSM bands (900 MHz and 1800 MHz. The printed monopole antenna is miniaturized by two meander-lines. The received signal from the receiving antenna is rectified by a voltage double using Schottky diode SMS-7630. The rectifier is optimized for low input power level of -20dBm using harmonic balance. Prototype is designed and fabricated. The simulation is validated by measurement with power conversion efficiency of 20% and 40.8% (in measurement at the input power level of -20dBm. The proposed rectenna has output voltage from 183-415 mV. From the measured results, this rectenna provides the possibility to harvest the ambient electromagnetic energy for powering low-power electronic devices.

  5. Prediction models in the design of neural network based ECG classifiers: A neural network and genetic programming approach

    Directory of Open Access Journals (Sweden)

    Smith Ann E

    2002-01-01

    Full Text Available Abstract Background Classification of the electrocardiogram using Neural Networks has become a widely used method in recent years. The efficiency of these classifiers depends upon a number of factors including network training. Unfortunately, there is a shortage of evidence available to enable specific design choices to be made and as a consequence, many designs are made on the basis of trial and error. In this study we develop prediction models to indicate the point at which training should stop for Neural Network based Electrocardiogram classifiers in order to ensure maximum generalisation. Methods Two prediction models have been presented; one based on Neural Networks and the other on Genetic Programming. The inputs to the models were 5 variable training parameters and the output indicated the point at which training should stop. Training and testing of the models was based on the results from 44 previously developed bi-group Neural Network classifiers, discriminating between Anterior Myocardial Infarction and normal patients. Results Our results show that both approaches provide close fits to the training data; p = 0.627 and p = 0.304 for the Neural Network and Genetic Programming methods respectively. For unseen data, the Neural Network exhibited no significant differences between actual and predicted outputs (p = 0.306 while the Genetic Programming method showed a marginally significant difference (p = 0.047. Conclusions The approaches provide reverse engineering solutions to the development of Neural Network based Electrocardiogram classifiers. That is given the network design and architecture, an indication can be given as to when training should stop to obtain maximum network generalisation.

  6. A Matheuristic for the Liner Shipping Network Design Problem with Transit Time Restrictions

    DEFF Research Database (Denmark)

    Brouer, Berit Dangaard; Desaulniers, Guy; Karsten, Christian Vad

    2015-01-01

    We present a mathematical model for the liner shipping network design problem with transit time restrictions on the cargo flow. We extend an existing matheuristic for the liner shipping network design problem to consider transit time restrictions. The matheuristic is an improvement heuristic, where...

  7. Reconfigurable Control Design with Neural Network Augmentation for a Modified F-15 Aircraft

    Science.gov (United States)

    Burken, John J.

    2007-01-01

    The viewgraphs present background information about reconfiguration control design, design methods used for paper, control failure survivability results, and results and time histories of tests. Topics examined include control reconfiguration, general information about adaptive controllers, model reference adaptive control (MRAC), the utility of neural networks, radial basis functions (RBF) neural network outputs, neurons, and results of investigations of failures.

  8. Hub network design for sparse travel demand within the African aviation industry

    CSIR Research Space (South Africa)

    Ssamula, B

    2007-07-01

    Full Text Available This paper analyses a study aimed at testing the cost effectiveness of designing a hub and spoke network (H&S network”) for Africa that allows airlines to reduce the costs of travel and increase connectivity. Various hub networks are designed using...

  9. Reconfigurable Flight Control Design using a Robust Servo LQR and Radial Basis Function Neural Networks

    Science.gov (United States)

    Burken, John J.

    2005-01-01

    This viewgraph presentation reviews the use of a Robust Servo Linear Quadratic Regulator (LQR) and a Radial Basis Function (RBF) Neural Network in reconfigurable flight control designs in adaptation to a aircraft part failure. The method uses a robust LQR servomechanism design with model Reference adaptive control, and RBF neural networks. During the failure the LQR servomechanism behaved well, and using the neural networks improved the tracking.

  10. Influence of Intra-cell Traffic on the Output Power of Base Station in GSM

    Directory of Open Access Journals (Sweden)

    M. Mileusnic

    2014-06-01

    Full Text Available In this paper we analyze the influence of intracell traffic in a GSM cell on the base station output power. It is proved that intracell traffic increases this power. If offered traffic is small, the increase of output power is equal to the part of intracell traffic. When the offered traffic and, as the result, call loss increase, the increase of output power becomes less. The results of calculation are verified by the computer simulation of traffic process in the GSM cell. The calculation and the simulation consider the uniform distribution of mobile users in the cell, but the conclusions are of a general nature.

  11. Effects of GSM-Frequency Electromagnetic Radiation on Some Physiological and Biochemical Parameters in Rats.

    Science.gov (United States)

    Khirazova, E E; Baizhumanov, A A; Trofimova, L K; Deev, L I; Maslova, M V; Sokolova, N A; Kudryashova, N Yu

    2012-10-01

    Single exposure of white outbred rats to electromagnetic radiation with a frequency 905 MHz (GSM frequency) for 2 h increased anxiety, reduced locomotor, orientation, and exploration activities in females and orientation and exploration activities in males. Glucocorticoid levels and antioxidant system activity increased in both males and females. In addition to acute effects, delayed effects of radiation were observed in both males and females 1 day after the exposure. These results demonstrated significant effect of GSM-range radiation on the behavior and activity of stress-realizing and stress-limiting systems of the body.

  12. Evaluation of Spectrum Usage for GSM band in Indoor and Outdoor Scenario for Dynamic Spectrum Access

    DEFF Research Database (Denmark)

    Patil, Kishor P.; Barge, Snehal; Skouby, Knud Erik

    2013-01-01

    Current wireless technologies allow limited flexibility in selection of operating frequency of the wireless devices. Cognitive radio is the potential candidate for the efficient spectrum usage in future due to its ability to modify their operational parameters such as frequency, modulation schemes...... measurement results of GSM band including statistical as well as spectral occupancy details obtained from measurement campaign conducted in Pune, India for indoor and outdoor scenarios. The results can be further used as an input for spectrum regulator for considering Cognitive Radio (CR) operation in GSM...

  13. Design on intelligent gateway technique in home network

    Science.gov (United States)

    Hu, Zhonggong; Feng, Xiancheng

    2008-12-01

    Based on digitization, multimedia, mobility, wide band, real-time interaction and so on,family networks, because can provide diverse and personalized synthesis service in information, correspondence work, entertainment, education and health care and so on, are more and more paid attention by the market. The family network product development has become the focus of the related industry. In this paper,the concept of the family network and the overall reference model of the family network are introduced firstly.Then the core techniques and the correspondence standard related with the family network are proposed.The key analysis is made for the function of family gateway, the function module of the software,the key technologies to client side software architecture and the trend of development of the family network entertainment seeing and hearing service and so on. Product present situation of the family gateway and the future trend of development, application solution of the digital family service are introduced. The development of the family network product bringing about the digital family network industry is introduced finally.It causes the development of software industries,such as communication industry,electrical appliances industry, computer and game and so on.It also causes the development of estate industry.

  14. Network Design: Best Practices for Alberta School Jurisdictions.

    Science.gov (United States)

    Schienbein, Ralph

    This report examines subsections of the computer network topology that relate to end-to-end performance and capacity planning in schools. Active star topology, Category 5 wiring, Ethernet, and intelligent devices are assumed. The report describes a model that can be used to project WAN (wide area network) connection speeds based on user traffic,…

  15. District Heating Network Design and Configuration Optimization with Genetic Algorithm

    DEFF Research Database (Denmark)

    Li, Hongwei; Svendsen, Svend

    2013-01-01

    and the pipe friction and heat loss formulations are non-linear. In order to find the optimal district heating network configuration, genetic algorithm which handles the mixed integer nonlinear programming problem is chosen. The network configuration is represented with binary and integer encoding...

  16. NM-Net Gigabit-based Implementation on Core Network Facilities and Network Design Hierarchy

    International Nuclear Information System (INIS)

    Raja Murzaferi Raja Moktar; Mohd Fauzi Haris; Siti Nurbahyah Hamdan

    2011-01-01

    Nuclear Malaysia computing network or NM the main backbone of internet working on operational staffs. Main network operating center or NOC is situated in Block 15 and linkup via fiber cabling to adjacent main network blocks (18, 29, 11 connections. Pre 2009 infrastructure; together to form the core networking switch. of the core network infrastructure were limited by the up link between core switches that is the Pair (UTP) Category 6 Cable. Furthermore, majority of the networking infrastructure throughout the agency were mainly built with Fast Ethernet Based specifications to date. With current research and operational tasks highly dependent on IT infrastructure that is being enabled through NM-Net, the performance NM-Net implementing gigabit-based networking system achieve optimal performance of internet networking services in the agency thus catalyze initiative. (author)

  17. GENETIC ALGORITHM BASED CONCEPT DESIGN TO OPTIMIZE NETWORK LOAD BALANCE

    Directory of Open Access Journals (Sweden)

    Ashish Jain

    2012-07-01

    Full Text Available Multiconstraints optimal network load balancing is an NP-hard problem and it is an important part of traffic engineering. In this research we balance the network load using classical method (brute force approach and dynamic programming is used but result shows the limitation of this method but at a certain level we recognized that the optimization of balanced network load with increased number of nodes and demands is intractable using the classical method because the solution set increases exponentially. In such case the optimization techniques like evolutionary techniques can employ for optimizing network load balance. In this paper we analyzed proposed classical algorithm and evolutionary based genetic approach is devise as well as proposed in this paper for optimizing the balance network load.

  18. Researching Design, Experience and Practice of Networked Learning

    DEFF Research Database (Denmark)

    Hodgson, Vivien; de Laat, Maarten; McConnell, David

    2014-01-01

    and final section draws attention to a growing topic of interest within networked learning: that of networked learning in informal practices. In addition, we provide a reflection on the theories, methods and settings featured in the networked learning research of the chapters. We conclude the introduction...... by discussing four main themes that have emerged from our reading of the chapters and which we believe are important in taking forward the theory of networked learning. They are as follows: practice as epistemology; the coupling of learning contexts (the relationship and connection of learning contexts......In the introductory chapter, we explore how networked learning has developed in recent years by summarising and discussing the research presented in the chapters of the book. The chapters are structured in three sections, each highlighting a particular aspect of practice. The first section focuses...

  19. Cross-Layer Design Approach for Power Control in Mobile Ad Hoc Networks

    Directory of Open Access Journals (Sweden)

    A. Sarfaraz Ahmed

    2015-03-01

    Full Text Available In mobile ad hoc networks, communication among mobile nodes occurs through wireless medium The design of ad hoc network protocol, generally based on a traditional “layered approach”, has been found ineffective to deal with receiving signal strength (RSS-related problems, affecting the physical layer, the network layer and transport layer. This paper proposes a design approach, deviating from the traditional network design, toward enhancing the cross-layer interaction among different layers, namely physical, MAC and network. The Cross-Layer design approach for Power control (CLPC would help to enhance the transmission power by averaging the RSS values and to find an effective route between the source and the destination. This cross-layer design approach was tested by simulation (NS2 simulator and its performance over AODV was found to be better.

  20. Integrated design of multivariable hydrometric networks using entropy theory with a multiobjective optimization approach

    Science.gov (United States)

    Keum, J.; Coulibaly, P. D.

    2017-12-01

    Obtaining quality hydrologic observations is the first step towards a successful water resources management. While remote sensing techniques have enabled to convert satellite images of the Earth's surface to hydrologic data, the importance of ground-based observations has never been diminished because in-situ data are often highly accurate and can be used to validate remote measurements. The existence of efficient hydrometric networks is becoming more important to obtain as much as information with minimum redundancy. The World Meteorological Organization (WMO) has recommended a guideline for the minimum hydrometric network density based on physiography; however, this guideline is not for the optimum network design but for avoiding serious deficiency from a network. Moreover, all hydrologic variables are interconnected within the hydrologic cycle, while monitoring networks have been designed individually. This study proposes an integrated network design method using entropy theory with a multiobjective optimization approach. In specific, a precipitation and a streamflow networks in a semi-urban watershed in Ontario, Canada were designed simultaneously by maximizing joint entropy, minimizing total correlation, and maximizing conditional entropy of streamflow network given precipitation network. After comparing with the typical individual network designs, the proposed design method would be able to determine more efficient optimal networks by avoiding the redundant stations, in which hydrologic information is transferable. Additionally, four quantization cases were applied in entropy calculations to assess their implications on the station rankings and the optimal networks. The results showed that the selection of quantization method should be considered carefully because the rankings and optimal networks are subject to change accordingly.

  1. Noticing climate change in electricity network design and construction

    International Nuclear Information System (INIS)

    Syri, S.; Martikeinen, A.; Lehtonen, M.

    2007-01-01

    The climate change is widely known to cause remarkable effects to electricity network systems on the whole. Some of the changes are good but the most of the changes cause disadvantages to electricity network. Consequence of climate change, blackouts can be long-standing which affect remarkable society and economic life. Most of electricity networks are coming to a renovation phase and the solutions, that are being made nowadays, affect still after decades. Taking account of climate change, now when networks are being developed and planned, it is possible to avoid possible large repair operation and increase reliability of distribution in the future. The aim of this project is to clarify how climate change should be noticed in planning and construction processes. According to the results of this project electricity network companies can be prepared for climate change by developing planning processes and network cost effectively. Also construction processes are being developed but emphasis is on planning process. The results and developed knowledge of VTT research project 'Impacts of climate change on electricity network business' are exploited in this project. In addition, impacts of climate change on cables and transformers are analyzed in collaboration with TKK in the project. (orig.)

  2. Semantic Parameters to Manage an Innovation Network Using Managing as Designing Approach: The Virtual Innovation Society Network Case

    Directory of Open Access Journals (Sweden)

    Cristiane Chaves Gattaz

    2014-06-01

    Full Text Available The most recent operations and management frameworks in innovation have not been complete to explicit required knowledge to manage the cooperation of its networked open innovation value chain in the knowledge economy and open enterprise. Strategic actors from the Virtual Innovation Society network were interviewed to identify critical semantic parameters that address this issue. As a result, this study suggests the characterization of inter-dependent added-values and its performance metrics, under the “managing as designing” approach, as input for managing the externalities, the integration of the articulation between business operations, strategy and information technology, and waste of innovation. In this context, the identification of the main managerial indicators for future command and control of existing innovation network operations under the “managing as designing” approach becomes a new challenge for future research.   Keywords: Managing as Designing; Innovation Management; Network Managament; Operations Management; Virtual Networks.

  3. Static and mobile networks design for atmospheric accidental releases monitoring

    International Nuclear Information System (INIS)

    Abida, R.

    2010-01-01

    The global context of my PhD thesis work is the optimization of air pollution monitoring networks, but more specifically it concerns the monitoring of accidental releases of radionuclides in air. The optimization problem of air quality measuring networks has been addresses in the literature. However, it has not been addresses in the context of surveillance of accidental atmospheric releases. The first part of my thesis addresses the optimization of a permanent network of monitoring of radioactive aerosols in the air, covering France. The second part concerns the problem of targeting of observations in case of an accidental release of radionuclides from a nuclear plant. (author)

  4. Synthetic tetracycline-inducible regulatory networks: computer-aided design of dynamic phenotypes.

    Science.gov (United States)

    Sotiropoulos, Vassilios; Kaznessis, Yiannis N

    2007-01-09

    Tightly regulated gene networks, precisely controlling the expression of protein molecules, have received considerable interest by the biomedical community due to their promising applications. Among the most well studied inducible transcription systems are the tetracycline regulatory expression systems based on the tetracycline resistance operon of Escherichia coli, Tet-Off (tTA) and Tet-On (rtTA). Despite their initial success and improved designs, limitations still persist, such as low inducer sensitivity. Instead of looking at these networks statically, and simply changing or mutating the promoter and operator regions with trial and error, a systematic investigation of the dynamic behavior of the network can result in rational design of regulatory gene expression systems. Sophisticated algorithms can accurately capture the dynamical behavior of gene networks. With computer aided design, we aim to improve the synthesis of regulatory networks and propose new designs that enable tighter control of expression. In this paper we engineer novel networks by recombining existing genes or part of genes. We synthesize four novel regulatory networks based on the Tet-Off and Tet-On systems. We model all the known individual biomolecular interactions involved in transcription, translation, regulation and induction. With multiple time-scale stochastic-discrete and stochastic-continuous models we accurately capture the transient and steady state dynamics of these networks. Important biomolecular interactions are identified and the strength of the interactions engineered to satisfy design criteria. A set of clear design rules is developed and appropriate mutants of regulatory proteins and operator sites are proposed. The complexity of biomolecular interactions is accurately captured through computer simulations. Computer simulations allow us to look into the molecular level, portray the dynamic behavior of gene regulatory networks and rationally engineer novel ones with useful

  5. Synthetic tetracycline-inducible regulatory networks: computer-aided design of dynamic phenotypes

    Directory of Open Access Journals (Sweden)

    Kaznessis Yiannis N

    2007-01-01

    Full Text Available Abstract Background Tightly regulated gene networks, precisely controlling the expression of protein molecules, have received considerable interest by the biomedical community due to their promising applications. Among the most well studied inducible transcription systems are the tetracycline regulatory expression systems based on the tetracycline resistance operon of Escherichia coli, Tet-Off (tTA and Tet-On (rtTA. Despite their initial success and improved designs, limitations still persist, such as low inducer sensitivity. Instead of looking at these networks statically, and simply changing or mutating the promoter and operator regions with trial and error, a systematic investigation of the dynamic behavior of the network can result in rational design of regulatory gene expression systems. Sophisticated algorithms can accurately capture the dynamical behavior of gene networks. With computer aided design, we aim to improve the synthesis of regulatory networks and propose new designs that enable tighter control of expression. Results In this paper we engineer novel networks by recombining existing genes or part of genes. We synthesize four novel regulatory networks based on the Tet-Off and Tet-On systems. We model all the known individual biomolecular interactions involved in transcription, translation, regulation and induction. With multiple time-scale stochastic-discrete and stochastic-continuous models we accurately capture the transient and steady state dynamics of these networks. Important biomolecular interactions are identified and the strength of the interactions engineered to satisfy design criteria. A set of clear design rules is developed and appropriate mutants of regulatory proteins and operator sites are proposed. Conclusion The complexity of biomolecular interactions is accurately captured through computer simulations. Computer simulations allow us to look into the molecular level, portray the dynamic behavior of gene regulatory

  6. Application of Artificial Neural Networks to the Design of Turbomachinery Airfoils

    Science.gov (United States)

    Rai, Man Mohan; Madavan, Nateri

    1997-01-01

    Artificial neural networks are widely used in engineering applications, such as control, pattern recognition, plant modeling and condition monitoring to name just a few. In this seminar we will explore the possibility of applying neural networks to aerodynamic design, in particular, the design of turbomachinery airfoils. The principle idea behind this effort is to represent the design space using a neural network (within some parameter limits), and then to employ an optimization procedure to search this space for a solution that exhibits optimal performance characteristics. Results obtained for design problems in two spatial dimensions will be presented.

  7. Information Flow Through Stages of Complex Engineering Design Projects: A Dynamic Network Analysis Approach

    DEFF Research Database (Denmark)

    Parraguez, Pedro; Eppinger, Steven D.; Maier, Anja

    2015-01-01

    The pattern of information flow through the network of interdependent design activities is thought to be an important determinant of engineering design process results. A previously unexplored aspect of such patterns relates to the temporal dynamics of information transfer between activities...... information flows between activities in complex engineering design projects; 2) we show how the network of information flows in a large-scale engineering project evolved over time and how network analysis yields several managerial insights; and 3) we provide a useful new representation of the engineering...... as those activities are implemented through the network of people executing the project. To address this gap, we develop a dynamic modeling method that integrates both the network of people and the network of activities in the project. We then employ a large dataset collected from an industrial setting...

  8. Cyber-physical system design with sensor networking technologies

    CERN Document Server

    Zeadally, Sherali

    2016-01-01

    This book describes how wireless sensor networking technologies can help in establishing and maintaining seamless communications between the physical and cyber systems to enable efficient, secure, reliable acquisition, management, and routing of data.

  9. Method for designing networking adaptive interactive hybrid systems

    NARCIS (Netherlands)

    Kester, L. J.H.M.

    2010-01-01

    Advances in network technologies enable distributed systems, operating in complex physical environments, to co-ordinate their activities over larger areas within shorter time intervals. Some envisioned application domains for such systems are defence, crisis management, traffic management and public

  10. Design and realization of a network security model

    OpenAIRE

    WANG, Jiahai; HAN, Fangxi; Tang, Zheng; TAMURA, Hiroki; Ishii, Masahiro

    2002-01-01

    The security of information is a key problem in the development of network technology. The basic requirements of security of information clearly include confidentiality, integrity, authentication and non-repudiation. This paper proposes a network security model that is composed of security system, security connection and communication, and key management. The model carries out encrypting, decrypting, signature and ensures confidentiality, integrity, authentication and non-repudiation. Finally...

  11. Network Design for Reliability and Resilience to Attack

    Science.gov (United States)

    2014-03-01

    Lieutenant Colonel, German Army Diplom- Ingenier , University of the German Armed Forces Munich 2002 M.S., Operations Research, Naval Postgraduate School...m-1 . . . . . . . . . . . . . . . . . . . . . . . 55 Figure 2.10 Germany road network . . . . . . . . . . . . . . . . . . . . . . . 56 Figure 2.11...based on the resulting bounding information. We develop a case study with a road network from Germany that consists of 2,971 nodes and 8,824 arcs, and

  12. Establishing and Leveraging networks in design education innovation projects

    OpenAIRE

    Spencer, Nick; Walden, Roderick; Leong, Benny; Bailey, Mark; Aftab, Mersha; University of Technology, Sydney; PolyU, Hongkong

    2014-01-01

    Project networking is the practice of obtaining needed services, ideas, or content by soliciting contributions from individuals, groups and organisations external to a project’s core team. The ability to establish and leverage networks is an increasingly important component of developing open innovation practices within many industries. This research examines the strategies and tactics employed by multidisciplinary undergraduate and postgraduate students to finding, forming and utilising idea...

  13. Design of real-time voice over internet protocol system under bandwidth network

    Science.gov (United States)

    Zhang, Li; Gong, Lina

    2017-04-01

    With the increasing bandwidth of the network and network convergence accelerating, VoIP means of communication across the network is becoming increasingly popular phenomenon. The real-time identification and analysis for VOIP flow over backbone network become the urgent needs and research hotspot of network operations management. Based on this, the paper proposes a VoIP business management system over backbone network. The system first filters VoIP data stream over backbone network and further resolves the call signaling information and media voice. The system can also be able to design appropriate rules to complete real-time reduction and presentation of specific categories of calls. Experimental results show that the system can parse and process real-time backbone of the VoIP call, and the results are presented accurately in the management interface, VoIP-based network traffic management and maintenance provide the necessary technical support.

  14. System-Level Design Methodologies for Networked Multiprocessor Systems-on-Chip

    DEFF Research Database (Denmark)

    Virk, Kashif Munir

    2008-01-01

    is the first such attempt in the published literature. The second part of the thesis deals with the issues related to the development of system-level design methodologies for networked multiprocessor systems-on-chip at various levels of design abstraction with special focus on the modeling and design...... at the system-level. The multiprocessor modeling framework is then extended to include models of networked multiprocessor systems-on-chip which is then employed to model wireless sensor networks both at the sensor node level as well as the wireless network level. In the third and the final part, the thesis...... to the transaction-level model. The thesis, as a whole makes contributions by describing a design methodology for networked multiprocessor embedded systems at three layers of abstraction from system-level through transaction-level to the cycle accurate level as well as demonstrating it practically by implementing...

  15. Research on key technology of planning and design for AC/DC hybrid distribution network

    Science.gov (United States)

    Shen, Yu; Wu, Guilian; Zheng, Huan; Deng, Junpeng; Shi, Pengjia

    2018-04-01

    With the increasing demand of DC generation and DC load, the development of DC technology, AC and DC distribution network integrating will become an important form of future distribution network. In this paper, the key technology of planning and design for AC/DC hybrid distribution network is proposed, including the selection of AC and DC voltage series, the design of typical grid structure and the comprehensive evaluation method of planning scheme. The research results provide some ideas and directions for the future development of AC/DC hybrid distribution network.

  16. Design and Implementation of a Wireless ZigBee Mesh Network

    OpenAIRE

    Ouyang, Chenxi

    2014-01-01

    ZigBee is officially a wireless network protocol that is designed to be used with the low-data-rate sensor and control networks. The objective of this thesis was to implement a ZigBee mesh network with XBee 802.15.4 RF module and Raspberry Pi. The target was to make a mesh network with three nodes. The project consists of two parts: using the X-CTU application to implement the ZigBee network with XBee RF modules, XBee 802.15.4 Starter Development Kit and XBee Adapter Board, and then the imple...

  17. Algorithm Design for Assignment Frequency Channels for Services in CATV Network

    Directory of Open Access Journals (Sweden)

    Jan Hlubik

    2008-01-01

    Full Text Available This article describes algorithm design for assignment frequency channels for services in CATV network. QAM modulated channels in designed system are dynamically switched and frequency adapted. On introduction, there is shortly described principle of providing analog video, digital video and data services in CATV network. Object of the article is focused on method of allocation individual TV and data channels on the frequency band. The conclusion compares advantages and disadvantages present and design system.

  18. GSM Marketing Service Providers Operations and Customers Satisfaction in Nigeria: An Empirical Investigation

    Directory of Open Access Journals (Sweden)

    Adebisi Sunday Abayomi

    2011-06-01

    Full Text Available This study has been carried out on the GSM arm of the Nigerian Telecomunication sectorto primarily investigate the level of satisfaction that the subscribers of GSM service providers haveenjoyed in the seven years of operations in Nigeria. In testing this empirically, MTN, GLOBACOMand ZAIN were selected as case studies. 600 questionnaires were administered on the subscribers ofthese GSM service providers in the Six States of the South-Western Nigeria using the purposivesampling technique. In analyzing the collated data, three hypotheses were tested with the use ofPercentages, T-test, F-test, [at 95% confidence limit], Cross-tabulation [using the ‘Eta’ Directionalmeasure] and statistical charts. The results from the SPSS 16 output rejected the Null hypotheses.This further indicated that, the various factors that determined the level of subscribers’ satisfactionwere statistically significant. The study therefore concluded that, subscribers in Nigeria aredissatisfied with the services of their service providers hence, the need for the regulatory body; NCCto ensure that subscribers interests are protected. The study then suggested that,, the GSM serviceproviders should reposition themselves to give adequate value to subscribers money incommensuration with their own gains from the Nigeria Telecommunications market.

  19. Experimental and numerical assessment of low-frequency current distributions from UMTS and GSM mobile phones.

    Science.gov (United States)

    Gosselin, Marie-Christine; Kühn, Sven; Kuster, Niels

    2013-12-07

    The evaluation of the exposure from mobile communication devices requires consideration of electromagnetic fields (EMFs) over a broad frequency range from dc to GHz. Mobile phones in operation have prominent spectral components in the low-frequency (LF) and radio-frequency (RF) ranges. While the exposure to RF fields from mobile phones has been comprehensively assessed in the past, the LF fields have received much less attention. In this study, LF fields from mobile phones are assessed experimentally and numerically for the global system for mobile (GSM) and universal mobile telecommunications system (UMTS) communication systems and conclusions about the global (LF and RF) EMF exposure from both systems are drawn. From the measurements of the time-domain magnetic fields, it was found that the contribution from the audio signal at a normal speech level, i.e., -16 dBm0, is the same order of magnitude as the fields induced by the current bursts generated from the implementation of the GSM communication system at maximum RF output level. The B-field induced by currents in phones using the UMTS is two orders of magnitude lower than that induced by GSM. Knowing that the RF exposure from the UMTS is also two orders of magnitude lower than from GSM, it is now possible to state that there is an overall reduction of the exposure from this communication system.

  20. Experimental and numerical assessment of low-frequency current distributions from UMTS and GSM mobile phones

    International Nuclear Information System (INIS)

    Gosselin, Marie-Christine; Kühn, Sven; Kuster, Niels

    2013-01-01

    The evaluation of the exposure from mobile communication devices requires consideration of electromagnetic fields (EMFs) over a broad frequency range from dc to GHz. Mobile phones in operation have prominent spectral components in the low-frequency (LF) and radio-frequency (RF) ranges. While the exposure to RF fields from mobile phones has been comprehensively assessed in the past, the LF fields have received much less attention. In this study, LF fields from mobile phones are assessed experimentally and numerically for the global system for mobile (GSM) and universal mobile telecommunications system (UMTS) communication systems and conclusions about the global (LF and RF) EMF exposure from both systems are drawn. From the measurements of the time-domain magnetic fields, it was found that the contribution from the audio signal at a normal speech level, i.e., −16 dBm0, is the same order of magnitude as the fields induced by the current bursts generated from the implementation of the GSM communication system at maximum RF output level. The B-field induced by currents in phones using the UMTS is two orders of magnitude lower than that induced by GSM. Knowing that the RF exposure from the UMTS is also two orders of magnitude lower than from GSM, it is now possible to state that there is an overall reduction of the exposure from this communication system. (paper)

  1. Experimental and numerical assessment of low-frequency current distributions from UMTS and GSM mobile phones

    Science.gov (United States)

    Gosselin, Marie-Christine; Kühn, Sven; Kuster, Niels

    2013-12-01

    The evaluation of the exposure from mobile communication devices requires consideration of electromagnetic fields (EMFs) over a broad frequency range from dc to GHz. Mobile phones in operation have prominent spectral components in the low-frequency (LF) and radio-frequency (RF) ranges. While the exposure to RF fields from mobile phones has been comprehensively assessed in the past, the LF fields have received much less attention. In this study, LF fields from mobile phones are assessed experimentally and numerically for the global system for mobile (GSM) and universal mobile telecommunications system (UMTS) communication systems and conclusions about the global (LF and RF) EMF exposure from both systems are drawn. From the measurements of the time-domain magnetic fields, it was found that the contribution from the audio signal at a normal speech level, i.e., -16 dBm0, is the same order of magnitude as the fields induced by the current bursts generated from the implementation of the GSM communication system at maximum RF output level. The B-field induced by currents in phones using the UMTS is two orders of magnitude lower than that induced by GSM. Knowing that the RF exposure from the UMTS is also two orders of magnitude lower than from GSM, it is now possible to state that there is an overall reduction of the exposure from this communication system.

  2. Link and Network Layers Design for Ultra-High-Speed Terahertz-Band Communications Networks

    Science.gov (United States)

    2017-01-01

    has hampered the use of the THz band for any application beyond sensing. However, many recent advancements with dierent technologies is finally...addition, the University at Bualo is currently preparing a US Patent Application for this invention. • Graphene-based Plasmonic Nano -antenna Arrays (Sec...networks [29] or the Internet of Nano -Things [34]. In this context, the development of a new communication and networking technology to support networks with

  3. Influence of D-net (EUROPEAN GSM-standard) cellular telephones on implanted pacemakers in children.

    Science.gov (United States)

    Elshershari, Huda; Celiker, Alpay; Ozer, Sema; Ozme, Sencan

    2002-09-01

    This study was designed to evaluate possible interactions between digital cellular telephones and implanted pacemakers in children. The study comprised 95 patients (53 males and 42 females) with a mean age of 11.5 +/- 4.6 years (range 1-22 years). The average time from pacemaker implantation was 2.5 years (range 1 month-12 years). Fourteen (15%) devices were dual chamber and the remaining were single chamber pacemakers. The following companies manufactured the pacemakers tested: Medtronic (n = 42), Telectronics (n = 9), Vitatron (n = 16), Pacesetter (n = 19), CPI (n = 8), and Biotronik (n = 1). All the patients were tested in the supine position during continuous ECG monitoring. After completion of the routine pacemaker check, the effects of the European Global system for mobile communication (GSM) was tested using two cellular telephone models (Ericsson GA 628 and Siemens S 25, 2-W power). For this purpose, atrial and ventricular sensitivity settings were programmed to the most sensitive values, and the tests were carried out in the unipolar and bipolar sensing modes. The evaluation was performed during ringing, switching on/off, and conversation phase with the cellular telephone positioned over the pulse generator and around the pacemaker pocket. A malfunction of the pacemaker was not observed in any patient. Only 1 (1%) of 95 patients showed a brief oversensing problem during calls with the cellular telephone. In this case, an AAIR pacemaker was implanted transvenously in a subcutaneous pocket and the sensing defect occurred only with the unipolar sensing mode and was not reproducible. Once the source of interference was removed, no sensing defect was detected and the patient remained asymptomatic. No symptoms were experienced in this study. The authors believe that pacemaker dependent patients with nonprotected pulse generators manufactured at the beginning of 1990s may be tested by their physicians for possible interferences before they use a digital cellular

  4. Multifuel multimodal network design; Projeto de redes multicombustiveis multimodal

    Energy Technology Data Exchange (ETDEWEB)

    Lage, Carolina; Dias, Gustavo; Bahiense, Laura; Ferreira Filho, Virgilio J.M. [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Coordenacao dos Programas de Pos-graduacao de Engenharia (COPPE). Programa de Engenharia de Producao

    2008-07-01

    The objective of the Multi commodity Multimodal Network Project is the development of modeling tools and methodologies for the optimal sizing of production networks and multimodal distribution of multiple fuel and its incomes, considering investments and transportation costs. Given the inherently non-linear combinatory nature of the problem, the resolution of real instances by the complete model, in an exact way, becomes computationally intractable. Thus, the strategy for resolution should contain a combination of exacts and heuristics methods, that must be applied to subdivisions of the original problem. This paper deals with one of these subdivisions, tackling the problem of modeling a network of pipelines in order to drain the production of ethanol away from the producing plants. The objective consists in defining the best network topology, minimizing investment and operational costs, and attending the total demand. In order to do that, the network was considered a tree, where the nodes are the center of producing regions and the edges are the pipelines, trough where the ethanol produced by plants must be drained away. The main objective also includes the decision over the optimal diameter of each pipeline and the optimal size of the bombs, in order to minimize the pumping costs. (author)

  5. KAJIAN PENGARUH MODERATING KELOMPOK PENGGUNA DALAM PENERIMAAN GSM-WLAN DI KOTA BANDUNG BERDASARKAN MODEL UTAUT

    Directory of Open Access Journals (Sweden)

    Syarif Hidayatulloh

    2016-03-01

    Full Text Available Abstract - The increasing use of the internet is testament to the rapid development of technology. GSM-WLAN is one technology that is manifested by the provider with the aim can hit 3G and 4G technology which requires a very large investment funds for the internet service provider. One of its main objectives is the big cities that became the majority of the largest internet usage in Indonesia, Bandung City region was no exception as the capital of the province and city tours. Therefore please note the acceptance of these technologies in the community. The model that is used to find out the level of acceptance and use of such technology is a Unified Theory of Acceptance and Use of Technology (UTAUT. In this study examined factors that supposedly affects the acceptance and use of technology GSM-WLAN in Bandung. Those factors among other performance expectancy, effort expectancy, social influence, facilitating conditions and price value to account for the contribution of each variable to predict the user's stance on such technology by using user groups as a moderator variable. Data processing method used is a Structural Equation Models (SEM that use software AMOS. The data processing of the obtained results performance expectancy value and price effect on attitudes toward the use of GSM technology-WLAN. While the moderator variable user groups influence on the attitude of the users in using GSM technology WLAN. Keywords: Internet, WLAN, GSM-UTAUT, SEM Abstrak - Penggunaan internet yang semakin meningkatnya merupakan bukti perkembangan teknologi yang sangat pesat. GSM-WLAN merupakan salah satu teknologi yang dihadirkan oleh para provider dengan tujuan dapat menekan penggunaan teknologi 3G dan 4G yang memerlukan innvestasi dana yang sangat besar bagi para penyedia layanan internet. Salah satu sasaran utamanya ialah kota-kota besar yang menjadi mayoritas penggunaan internet terbesar di Indonesia, tidak terkecuali wilayah Kota Bandung sebagai Ibu kota

  6. Active-Varying Sampling-Based Fault Detection Filter Design for Networked Control Systems

    Directory of Open Access Journals (Sweden)

    Yu-Long Wang

    2014-01-01

    Full Text Available This paper is concerned with fault detection filter design for continuous-time networked control systems considering packet dropouts and network-induced delays. The active-varying sampling period method is introduced to establish a new discretized model for the considered networked control systems. The mutually exclusive distribution characteristic of packet dropouts and network-induced delays is made full use of to derive less conservative fault detection filter design criteria. Compared with the fault detection filter design adopting a constant sampling period, the proposed active-varying sampling-based fault detection filter design can improve the sensitivity of the residual signal to faults and shorten the needed time for fault detection. The simulation results illustrate the merits and effectiveness of the proposed fault detection filter design.

  7. Recognizing climate change in electricity network design and construction

    Energy Technology Data Exchange (ETDEWEB)

    Haenninen, S.; Pykaelae, M.-L.; Martikainen, A.; Farin, J. (VTT Technical Research Centre of Finland, Espoo (Finland))

    2009-07-01

    VTT has studied the impact of the climate change on the reliability of the medium voltage electricity network in Finland. The climate change concerning the planning and building of electric power networks was predicted using climate models and emission scenarios giving the mean value of the changes in 30 years. The Rossby Centre regional Atmosphere-Ocean model was the basis for the calculations. Two global climate models and two emission scenarios have been taken as boundary situations in order to take into account the uncertainty of the development in the future. The importance of the effects is shown as costs and failure durations for different line structures in different regions. On the basis of all these factors it will be judged how strong an effect the climate change has in the present electric power network and how one should be prepared for it. It is profitable to consider the final impacts in detail, because the weather causes faults in different ways depending on environmental conditions. Poor access to the fault locations increases the repairing time. Based on the calculations the influence of climate change is much lower at the roadside and even lower in the fields. Urban networks are already mostly underground cable networks having considerably lower climate effects than the overhead line network. The significance of the calculation results is estimated by comparing the calculated costs caused by the weather conditions to the total costs. Moreover, the influence of the climate change on the loading capacity of the power system components is presented. Impacts of the climate change on cables and transformers have been analyzed by TKK Power Systems and High Voltage Engineering. (orig.)

  8. A systematic molecular circuit design method for gene networks under biochemical time delays and molecular noises

    Directory of Open Access Journals (Sweden)

    Chang Yu-Te

    2008-11-01

    Full Text Available Abstract Background Gene networks in nanoscale are of nonlinear stochastic process. Time delays are common and substantial in these biochemical processes due to gene transcription, translation, posttranslation protein modification and diffusion. Molecular noises in gene networks come from intrinsic fluctuations, transmitted noise from upstream genes, and the global noise affecting all genes. Knowledge of molecular noise filtering and biochemical process delay compensation in gene networks is crucial to understand the signal processing in gene networks and the design of noise-tolerant and delay-robust gene circuits for synthetic biology. Results A nonlinear stochastic dynamic model with multiple time delays is proposed for describing a gene network under process delays, intrinsic molecular fluctuations, and extrinsic molecular noises. Then, the stochastic biochemical processing scheme of gene regulatory networks for attenuating these molecular noises and compensating process delays is investigated from the nonlinear signal processing perspective. In order to improve the robust stability for delay toleration and noise filtering, a robust gene circuit for nonlinear stochastic time-delay gene networks is engineered based on the nonlinear robust H∞ stochastic filtering scheme. Further, in order to avoid solving these complicated noise-tolerant and delay-robust design problems, based on Takagi-Sugeno (T-S fuzzy time-delay model and linear matrix inequalities (LMIs technique, a systematic gene circuit design method is proposed to simplify the design procedure. Conclusion The proposed gene circuit design method has much potential for application to systems biology, synthetic biology and drug design when a gene regulatory network has to be designed for improving its robust stability and filtering ability of disease-perturbed gene network or when a synthetic gene network needs to perform robustly under process delays and molecular noises.

  9. Design of neural networks for classification of remotely sensed imagery

    Science.gov (United States)

    Chettri, Samir R.; Cromp, Robert F.; Birmingham, Mark

    1992-01-01

    Classification accuracies of a backpropagation neural network are discussed and compared with a maximum likelihood classifier (MLC) with multivariate normal class models. We have found that, because of its nonparametric nature, the neural network outperforms the MLC in this area. In addition, we discuss techniques for constructing optimal neural nets on parallel hardware like the MasPar MP-1 currently at GSFC. Other important discussions are centered around training and classification times of the two methods, and sensitivity to the training data. Finally, we discuss future work in the area of classification and neural nets.

  10. Statistical theory of designed quantum transport across disordered networks

    Science.gov (United States)

    Walschaers, Mattia; Mulet, Roberto; Wellens, Thomas; Buchleitner, Andreas

    2015-04-01

    We explain how centrosymmetry, together with a dominant doublet of energy eigenstates in the local density of states, can guarantee interference-assisted, strongly enhanced, strictly coherent quantum excitation transport between two predefined sites of a random network of two-level systems. Starting from a generalization of the chaos-assisted tunnelling mechanism, we formulate a random matrix theoretical framework for the analytical prediction of the transfer time distribution, of lower bounds of the transfer efficiency, and of the scaling behavior of characteristic statistical properties with the size of the network. We show that these analytical predictions compare well to numerical simulations, using Hamiltonians sampled from the Gaussian orthogonal ensemble.

  11. The design of a Bayesian Network for mobility management in Wireless Sensor Networks

    NARCIS (Netherlands)

    Ballari, D.E.; Wachowicz, M.

    2010-01-01

    Mobility management functions in WSNs are mainly being developed from a ommunicational point of view, since the focus has been on maintaining the network connectivity. However, from a sensing point of view, sensor mobility has also an impact on the network spatial coverage. In mobile WSNs, the

  12. An Approach to Optical Network Design using General Heuristic Optimization Framework

    Directory of Open Access Journals (Sweden)

    Marko Lacković

    2010-12-01

    Full Text Available The article tackles the problem of optimization methods in optical network design process, based on optimal traffic routing with the goal to minimize the utilized network resources for given topology and traffic demands. An optimization framework Nyx has been developed with the focus on flexibility in solving optimization problems by implementing general heuristic search techniques. Nyx modular organization has been described, including coding types for solutions and genetic algorithm as the optimization method. Optimal routing has been implemented to demonstrate the use of Nyx in the optical network design process. Optimal routing procedure has been applied to Pan-European optical network with variations of routing procedures and the number of wavelengths. The analysis included no protection scenario, 1+1 protection and path restoration. The routing was performed using shortest path routing and optimal routing which minimizes the use of optical network resources, being network multiplexers, amplifiers and fibers.  

  13. Designing optimal transportation networks: a knowledge-based computer-aided multicriteria approach

    Energy Technology Data Exchange (ETDEWEB)

    Tung, S.I.

    1986-01-01

    The dissertation investigates the applicability of using knowledge-based expert systems (KBES) approach to solve the single-mode (automobile), fixed-demand, discrete, multicriteria, equilibrium transportation-network-design problem. Previous works on this problem has found that mathematical programming method perform well on small networks with only one objective. Needed is a solution technique that can be used on large networks having multiple, conflicting criteria with different relative importance weights. The KBES approach developed in this dissertation represents a new way to solve network design problems. The development of an expert system involves three major tasks: knowledge acquisition, knowledge representation, and testing. For knowledge acquisition, a computer aided network design/evaluation model (UFOS) was developed to explore the design space. This study is limited to the problem of designing an optimal transportation network by adding and deleting capacity increments to/from any link in the network. Three weighted criteria were adopted for use in evaluating each design alternative: cost, average V/C ratio, and average travel time.

  14. Urban Green Network Design: Defining green network from an urban planning perspective

    Directory of Open Access Journals (Sweden)

    Andrea Tulisi

    2017-08-01

    Full Text Available From the theoretical context of Smart City various studies have emerged that adopt an analytical approach and description of urban phenomena based on the principles of “network design”; this line of research uses the network systems theory to define the principles that regulate the relationships among the various elements of urban sub-systems in order to optimize their functionality. From the same theoretical basis, urban greenspaces have also been studied as networks, by means of the creation of models capable of measuring the performance of the system in its entirety, posing the basis of a new multy-disciplinary research field called green network. This paper presents the results of research aimed at clarifying the meaning of green network from an urban planning perspective through a lexical analysis applied to a textual corpus of more than 300 abstracts of research papers that have dealt with this topic over the last twenty years. The results show that the concept of green network appears still fuzzy and unclear, due to the different meaning given to the term “green” and to an incorrect use of the term “network”, often referred to as a generic set of natural areas present in a city, without any reference to the network system theory or to the basic rules linking these elements together. For this reason, the paper proposes a unique definition of green network from an urban planning perspective that takes into account the contribution of other research areas to effective green infrastructure planning. This is the concept of “urban green network design” defined as “an urban planning practice, supported by decision support tools able to model green infrastructure as network, composed by natural and semi-natural areas, whose connections are modelled according to specific variables, in order to deliver an equal distribution of public services for enhancing the quality of life as well as a wide range of ecosystem services”.

  15. Conceptual design of data management and communication networks for KALIMER MMIS

    International Nuclear Information System (INIS)

    Cha, K. H.; Kwon, K. C.

    1998-01-01

    This paper describes the design progress for data management and communication networks to be co-operated as subsystems in KALIMER MMIS. Main functions and design bases are being established and validated for functional modules of these subsystems. Real-time data acquisition and signal validation, databases, and data logging have been designed as each functional module of data management while data interfaces of communication networks have been designed with the system information from Top-Tier Requirements for KALIMER MMIS. The conceptual design shall be refined through the iterative and detailed one

  16. Formulation and Design of a CO2 Utilization Network Detailed Through a Conceptual Example

    DEFF Research Database (Denmark)

    Frauzem, Rebecca; Fjellerup, Kasper; Gani, Rafiqul

    information is available to describe the network mathematically, the most promising paths based on known technologies are designed and analyzed first. This makes the stages iterative rather than purely sequential. As part of this, the network is analyzed in the conceptual example of methanol synthesis via CO2...... for economic feasibility and environmental sustainability. Using computer-aided methods, the feasibility and sustainability of CO2 conversion is shown through the design and optimization of a methanol synthesis process....... involves three stages: a process synthesis stage, a design stage and an innovation stage. Following a superstructure based approach, a network of conversion processes is created. This network links CO2 and products through various processing blocks. The network also links carbon capture to ensure...

  17. Design, deployment and performance of 4G-LTE networks a practical approach

    CERN Document Server

    ElNashar, Ayman; Sherif, Mahmoud

    2014-01-01

    This book provides an insight into the key practical aspects and best practice of 4G-LTE network design, performance, and deployment Design, Deployment and Performance of 4G-LTE Networks addresses the key practical aspects and best practice of 4G networks design, performance, and deployment. In addition, the book focuses on the end-to-end aspects of the LTE network architecture and different deployment scenarios of commercial LTE networks. It describes the air interface of LTE focusing on the access stratum protocol layers: PDCP, RLC, MAC, and Physical Layer. The air interface described in this book covers the concepts of LTE frame structure, downlink and uplink scheduling, and detailed illustrations of the data flow across the protocol layers. It describes the details of the optimization process including performance measurements and troubleshooting mechanisms in addition to demonstrating common issues and case studies based on actual field results. The book provides detailed performance analysis of key fe...

  18. Enhancing Energy Efficiency of Wireless Sensor Network through the Design of Energy Efficient Routing Protocol

    Directory of Open Access Journals (Sweden)

    Noor Zaman

    2016-01-01

    Full Text Available Wireless Sensor Network (WSN is known to be a highly resource constrained class of network where energy consumption is one of the prime concerns. In this research, a cross layer design methodology was adopted to design an energy efficient routing protocol entitled “Position Responsive Routing Protocol” (PRRP. PRRP is designed to minimize energy consumed in each node by (1 reducing the amount of time in which a sensor node is in an idle listening state and (2 reducing the average communication distance over the network. The performance of the proposed PRRP was critically evaluated in the context of network lifetime, throughput, and energy consumption of the network per individual basis and per data packet basis. The research results were analyzed and benchmarked against the well-known LEACH and CELRP protocols. The outcomes show a significant improvement in the WSN in terms of energy efficiency and the overall performance of WSN.

  19. Note: Design and development of wireless controlled aerosol sampling network for large scale aerosol dispersion experiments

    Energy Technology Data Exchange (ETDEWEB)

    Gopalakrishnan, V.; Subramanian, V.; Baskaran, R.; Venkatraman, B. [Radiation Impact Assessment Section, Radiological Safety Division, Indira Gandhi Centre for Atomic Research, Kalpakkam 603 102 (India)

    2015-07-15

    Wireless based custom built aerosol sampling network is designed, developed, and implemented for environmental aerosol sampling. These aerosol sampling systems are used in field measurement campaign, in which sodium aerosol dispersion experiments have been conducted as a part of environmental impact studies related to sodium cooled fast reactor. The sampling network contains 40 aerosol sampling units and each contains custom built sampling head and the wireless control networking designed with Programmable System on Chip (PSoC™) and Xbee Pro RF modules. The base station control is designed using graphical programming language LabView. The sampling network is programmed to operate in a preset time and the running status of the samplers in the network is visualized from the base station. The system is developed in such a way that it can be used for any other environment sampling system deployed in wide area and uneven terrain where manual operation is difficult due to the requirement of simultaneous operation and status logging.

  20. Note: Design and development of wireless controlled aerosol sampling network for large scale aerosol dispersion experiments

    Science.gov (United States)

    Gopalakrishnan, V.; Subramanian, V.; Baskaran, R.; Venkatraman, B.

    2015-07-01

    Wireless based custom built aerosol sampling network is designed, developed, and implemented for environmental aerosol sampling. These aerosol sampling systems are used in field measurement campaign, in which sodium aerosol dispersion experiments have been conducted as a part of environmental impact studies related to sodium cooled fast reactor. The sampling network contains 40 aerosol sampling units and each contains custom built sampling head and the wireless control networking designed with Programmable System on Chip (PSoC™) and Xbee Pro RF modules. The base station control is designed using graphical programming language LabView. The sampling network is programmed to operate in a preset time and the running status of the samplers in the network is visualized from the base station. The system is developed in such a way that it can be used for any other environment sampling system deployed in wide area and uneven terrain where manual operation is difficult due to the requirement of simultaneous operation and status logging.

  1. Visually Augmented Analysis of Socio-Technical Networks in Engineering Systems Design Research

    DEFF Research Database (Denmark)

    Storga, M.; Stankovic, T.; Cash, Philip

    2013-01-01

    /service-system (PSS) life cycle) may be applied in engineering design research. Network thinking of the kind described in this paper could be fundamental for developing new and effective techniques for solving the problems in the engineering design research related to the interpretation of the huge amount of data...... captured during experiments and observations that are more and more used as a main research method. Case studies that are presented illustrate also the significance of the network based research approach in providing insight into ways of improving the design process for complex engineering systems......., but only fairly recently has the study of networks in general become a major topic of research in complex engineering systems. The research reported in this paper is discussing how the visually augmented analysis of complex socio-networks (networks of people and technology engaged in a product...

  2. Methodology for optimal design of efficient air transport network in a competitive environment

    OpenAIRE

    Trapote Barreira, César

    2015-01-01

    This thesis aims to dissert about air transport network design taking into consideration the current needs about efficiency in a very competitive industry. The main focus for this work is the airline's point of view and for this reason is going to be common to talk about profitability. A methodology is proposed to analyse current networks and to introduce modifications. First, an analytical approach is proposed with the aim to understand better the interaction of key parameters in network ...

  3. State criminal justice telecommunications (STACOM). Volume 4: Network design software user's guide

    Science.gov (United States)

    Lee, J. J.

    1977-01-01

    A user's guide to the network design program is presented. The program is written in FORTRAN V and implemented on a UNIVAC 1108 computer under the EXEC-8 operating system which enables the user to construct least-cost network topologies for criminal justice digital telecommunications networks. A complete description of program features, inputs, processing logic, and outputs is presented, and a sample run and a program listing are included.

  4. Financial risk analysis in the synthesis and design of processing networks: Balancing risk and return

    DEFF Research Database (Denmark)

    Quaglia, Alberto; Sin, Gürkan; Gani, Rafiqul

    2014-01-01

    The construction of a processing network is a corporate investment, that processing companies make with the goal of creating the conditions to increase their value. In a previous work, a computer-aided framework supporting the design of processing network under uncertainty has been presented...... and financial risk models. Through the solution of a small benchmark problem, the impact of financial factors on the optimal network configuration is presented and discussed....

  5. Optimal scope of supply chain network & operations design

    NARCIS (Netherlands)

    Ma, N.

    2014-01-01

    The increasingly complex supply chain networks and operations call for the development of decision support systems and optimization techniques that take a holistic view of supply chain issues and provide support for integrated decision-making. The economic impacts of optimized supply chain are

  6. Bayesian and neural networks for preliminary ship design

    DEFF Research Database (Denmark)

    Clausen, H. B.; Lützen, Marie; Friis-Hansen, Andreas

    2001-01-01

    000 ships is acquired and various methods for derivation of empirical relations are employed. A regression analysis is carried out to fit functions to the data. Further, the data are used to learn Bayesian and neural networks to encode the relations between the characteristics. On the basis...

  7. An optimization approach for district heating strategic network design

    NARCIS (Netherlands)

    Bordin, Chiara; Gordini, Angelo; Vigo, Daniele

    2016-01-01

    District heating systems provide the heat generated in a centralized location to a set of users for their residential and commercial heating requirements. Heat distribution is generally obtained by using hot water or steam flowing through a closed network of insulated pipes and heat exchange

  8. Design and Optimisation Problems in Wireless Sensor Networks

    Indian Academy of Sciences (India)

    Premkumar Karumbu,1.05 ECE,,+91-9448227167

    2010-11-14

    Nov 14, 2010 ... Nodes contain pieces of a distributed signal processing algorithm. Computations are performed on the measurements ... Potential Applications of Wireless Sensor Networks. Environment monitoring .... Minimise detection delay s.t. a false alarm probability bound, i.e., min E((˜U − T)I{ ˜T≥T}) subject to. Pr (.

  9. Sustainable reverse logistics network design for household plastic waste

    NARCIS (Netherlands)

    Bing, X.; Bloemhof, J.M.; Vorst, van der J.G.A.J.

    2014-01-01

    Plastic recycling is a legal requirement and can yield environmental benefits. In the Netherlands, there is a complex network of various collection methods, separation centers, sorting centers and reprocessors. The first step of the recycling system, separating plastics from other waste, can occur

  10. The Canarian Seismic Monitoring Network: design, development and first result

    Science.gov (United States)

    D'Auria, Luca; Barrancos, José; Padilla, Germán D.; García-Hernández, Rubén; Pérez, Aaron; Pérez, Nemesio M.

    2017-04-01

    Tenerife is an active volcanic island which experienced several eruptions of moderate intensity in historical times, and few explosive eruptions in the Holocene. The increasing population density and the consistent number of tourists are constantly raising the volcanic risk. In June 2016 Instituto Volcanologico de Canarias started the deployment of a seismological volcano monitoring network consisting of 15 broadband seismic stations. The network began its full operativity in November 2016. The aim of the network are both volcano monitoring and scientific research. Currently data are continuously recorded and processed in real-time. Seismograms, hypocentral parameters, statistical informations about the seismicity and other data are published on a web page. We show the technical characteristics of the network and an estimate of its detection threshold and earthquake location performances. Furthermore we present other near-real time procedures on the data: analysis of the ambient noise for determining the shallow velocity model and temporal velocity variations, detection of earthquake multiplets through massive data mining of the seismograms and automatic relocation of events through double-difference location.

  11. Design and Optimisation Problems in Wireless Sensor Networks

    Indian Academy of Sciences (India)

    Premkumar Karumbu,1.05 ECE,,+91-9448227167

    2010-11-14

    Nov 14, 2010 ... Motes are deployed and self-organise into a mesh network. Nodes contain pieces of a distributed signal processing algorithm. Computations are performed on the measurements. Partial results flow over the links. Downstream nodes combine their inputs and forward the results. The MAC schedules the ...

  12. Designing a dynamic network based approach for asset management activities

    NARCIS (Netherlands)

    Volker, L.; Scharpff, J.; De Weerdt, M.M.; Herder, P.M.

    2012-01-01

    Transportation networks are important public infrastructures because they enable economic and social activity. Trends in contracting the maintenance of such assets have caused a shift in governance from a public body to market-like arrangements and changed the roles and responsibilities among asset

  13. Evolving RBF neural networks for adaptive soft-sensor design.

    Science.gov (United States)

    Alexandridis, Alex

    2013-12-01

    This work presents an adaptive framework for building soft-sensors based on radial basis function (RBF) neural network models. The adaptive fuzzy means algorithm is utilized in order to evolve an RBF network, which approximates the unknown system based on input-output data from it. The methodology gradually builds the RBF network model, based on two separate levels of adaptation: On the first level, the structure of the hidden layer is modified by adding or deleting RBF centers, while on the second level, the synaptic weights are adjusted with the recursive least squares with exponential forgetting algorithm. The proposed approach is tested on two different systems, namely a simulated nonlinear DC Motor and a real industrial reactor. The results show that the produced soft-sensors can be successfully applied to model the two nonlinear systems. A comparison with two different adaptive modeling techniques, namely a dynamic evolving neural-fuzzy inference system (DENFIS) and neural networks trained with online backpropagation, highlights the advantages of the proposed methodology.

  14. Comparison of grey scale median (GSM) measurement in ultrasound images of human carotid plaques using two different softwares.

    Science.gov (United States)

    Östling, Gerd; Persson, Margaretha; Hedblad, Bo; Gonçalves, Isabel

    2013-11-01

    Grey scale median (GSM) measured on ultrasound images of carotid plaques has been used for several years now in research to find the vulnerable plaque. Centres have used different software and also different methods for GSM measurement. This has resulted in a wide range of GSM values and cut-off values for the detection of the vulnerable plaque. The aim of this study was to compare the values obtained with two different softwares, using different standardization methods, for the measurement of GSM on ultrasound images of carotid human plaques. GSM was measured with Adobe Photoshop(®) and with Artery Measurement System (AMS) on duplex ultrasound images of 100 consecutive medium- to large-sized carotid plaques of the Beta-blocker Cholesterol-lowering Asymptomatic Plaque Study (BCAPS). The mean values of GSM were 35·2 ± 19·3 and 55·8 ± 22·5 for Adobe Photoshop(®) and AMS, respectively. Mean difference was 20·45 (95% CI: 19·17-21·73). Although the absolute values of GSM differed, the agreement between the two measurements was good, correlation coefficient 0·95. A chi-square test revealed a kappa value of 0·68 when studying quartiles of GSM. The intra-observer variability was 1·9% for AMS and 2·5% for Adobe Photoshop. The difference between softwares and standardization methods must be taken into consideration when comparing studies. To avoid these problems, researcher should come to a consensus regarding software and standardization method for GSM measurement on ultrasound images of plaque in the arteries. © 2013 Scandinavian Society of Clinical Physiology and Nuclear Medicine. Published by John Wiley & Sons Ltd.

  15. The consideration of dynamics and control in the design of heat exchanger networks

    International Nuclear Information System (INIS)

    Reimann, K.A.

    1986-03-01

    The heat exchanger network method is a way of abstracting the enthalpy and heat flows from the blueprints of a planned or existing processing plant. It enables a systematic design of a plant-wide heat recovery system which is optimal with regard to energy costs, capital costs and operational requirements. A heat exchanger network is a representation of all heat transfer relations between hot process streams and cold process streams within a plant. During the past ten years, the optimal design of heat exchanger networks (i.e. the optimal arrangement of heat transfer relations within a plant) has developed into a field of research of its own. Both, static methods ('interaction analysis') and dynamic methods ('process reaction curve analysis') from control theory have been used to explore the new field of heat exchanger network dynamics. As a major tool, an interactive, portable computer program for network simulation and controllability assessment has been developed (it is available as a design tool within the frame of the International Energy Agency). Based on the well-understood global parameters: effectiveness and NTU, which follow from the network design, some straightforward methods covering the following topics are presented: - 'paths' for control and disturbance signal transfer across the network, - locations of control bypasses around heat exchangers, and their capacity of emitting control signals or absorbing disturbances, - influence of the equipment besides the heat exchangers (which can be regarded as 'surrounding' the network, thus forming an 'associated' network). It has been found that networks which are designed according to the 'pinch-based' method have a potential for good controllability. It is shown how, using the freedoms given in the 'pinch-based' design and the above-mentioned methods, that potential is put into effect. (author)

  16. Power Terminal Communication Access Network Monitoring System Scheme Based on Design Patterns

    Science.gov (United States)

    Yan, Shengchao; Wu, Desheng; Zhu, Jiang

    2018-01-01

    In order to realize patterns design for terminal communication monitoring system, this paper introduces manager-workers, tasks-workers design patterns, based on common design patterns such as factory method, chain of responsibility, facade. Using these patterns, the communication monitoring system which combines module-groups like networking communication, business data processing and the peripheral support has been designed successfully. Using these patterns makes this system have great flexibility and scalability and improves the degree of systematic pattern design structure.

  17. Enriching the Tactical Network Design of Express Service Carriers with Fleet Scheduling Characteristics

    NARCIS (Netherlands)

    Meuffels, W.J.M.; Fleuren, H.A.; Cruijssen, F.C.A.M.; van Dam, E.R.

    2009-01-01

    Express service carriers provide time-guaranteed deliveries of parcels via a network consisting of nodes and hubs. In this, nodes take care of the collection and delivery of parcels, and hubs have the function to consolidate parcels in between the nodes. The tactical network design problem assigns

  18. Enriching the tactical network design of express service carriers with fleet scheduling characteristics

    NARCIS (Netherlands)

    Meuffels, W.J.M.; Fleuren, H.A.; Cruijssen, F.C.A.M.; Dam, E.R.

    2010-01-01

    Express service carriers provide time-guaranteed deliveries of parcels via a network consisting of nodes and hubs. In this, nodes take care of the collection and delivery of parcels, and hubs have the function to consolidate parcels in between the nodes. The tactical network design problem assigns

  19. Hypothesis Management Framework: a exible design pattern for belief networks in decision support systems

    NARCIS (Netherlands)

    Gosliga, S.P. van; Voorde, I. van de

    2008-01-01

    This article discusses a design pattern for building belief networks for application domains in which causal models are hard to construct. In this approach we pursue a modular belief network structure that is easily extended by the users themselves, while remaining reliable for decision support. The

  20. Design of multi-layer neural networks for accurate identification of nonlinear mappings

    Science.gov (United States)

    Teixeira, Edilberto; Loparo, Kenneth; Gomide, Fernando A. C.

    1991-01-01

    Guidelines for the design of multilayer neural networks for the identification of nonlinear mappings are considered. Since nonlinear mappings can be approximated by a one-hidden-layer neural network, an approach to determine the sufficient number of hidden layer nodes to achieve a global minima of the identification error function is considered.

  1. Cacti beginner's guide leverage Cacti to design a robust network operations center

    CERN Document Server

    Urban, Thomas

    2017-01-01

    The book is designed in such a way that you can explore it chapter-by-chapter or skip any chapter without missing a beat. If you are a network operator and want to use Cacti for implementing performance measurement for trending, troubleshooting, and reporting purposes, then this book is for you. You only need to know the basics of network ...

  2. A systematic framework for enterprise-wide optimization: Synthesis and design of processing network under uncertainty

    DEFF Research Database (Denmark)

    Quaglia, Alberto; Sarup, Bent; Sin, Gürkan

    2013-01-01

    In this paper, a systematic framework for synthesis and design of processing networks under uncertaintyis presented. Through the framework, an enterprise-wide optimization problem is formulated and solvedunder uncertain conditions, to identify the network (composed of raw materials, process techn...

  3. Performance of a genetic algorithm for solving the multi-objective, multimodel transportation network design problem

    NARCIS (Netherlands)

    Brands, Ties; van Berkum, Eric C.

    2014-01-01

    The optimization of infrastructure planning in a multimodal network is defined as a multi-objective network design problem, with accessibility, use of urban space by parking, operating deficit and climate impact as objectives. Decision variables are the location of park and ride facilities, train

  4. Safe design and operation of tank reactors for multiple-reaction networks: uniqueness and multiplicity

    NARCIS (Netherlands)

    Westerterp, K.R.; Westerink, E.J.

    1990-01-01

    A method is developed to design a tank reactor in which a network of reactions is carried out. The network is a combination of parallel and consecutive reactions. The method ensures unique operation. Dimensionless groups are used which are either representative of properties of the reaction system

  5. WiFiSiM: An Educational Tool for the Study and Design of Wireless Networks

    Science.gov (United States)

    Mateo Sanguino, T. J.; Serrano Lopez, C.; Marquez Hernandez, F. A.

    2013-01-01

    A new educational simulation tool designed for the generic study of wireless networks, the Wireless Fidelity Simulator (WiFiSim), is presented in this paper. The goal of this work was to create and implement a didactic tool to improve the teaching and learning of computer networks by means of two complementary strategies: simulating the behavior…

  6. Practical network design techniques a complete guide for WANs and LANs

    CERN Document Server

    Held, Gilbert

    2004-01-01

    This new edition has two parts. The first part focuses on wide area networks; the second, which is entirely new, focuses on local area networks. Because Ethernet emerged victorious in the LAN war, the second section pays particular attention to Ethernet design and performance characteristics.

  7. A Note on the Art of Network Design Problems | Osagiede | Journal ...

    African Journals Online (AJOL)

    In this study, we describe some Network Design Problems (NDPs) as well as the network flowbased improvement algorithm for neighbourhood search defined by cycles. The main part of the study is structured around the formulation of the expected duration of stay in the educational system as a NDP. The fundamental ...

  8. Hybrid neural network model for the design of beam subjected to ...

    Indian Academy of Sciences (India)

    structural design are controlled by many codes and regulations, the structural engineer has to exercise caution and use his judgement in ... Lot of research has taken place on applications of artificial neural networks in structural engineering. .... been selected for this network model. The architecture is depicted in figure 1.

  9. Multi-objective transportation network design: Accelerating search by applying ε-NSGAII

    NARCIS (Netherlands)

    Brands, Ties; Wismans, Luc Johannes Josephus; van Berkum, Eric C.; Coello, C.C.

    2014-01-01

    The optimization of infrastructure planning in a multimodal passenger transportation network is formulated as a multi-objective network design problem, with accessibility, use of urban space by parking, operating deficit and climate impact as objectives. Decision variables are the location of park

  10. Financial risk analysis in the synthesis and design of processing networks: Balancing risk and return

    DEFF Research Database (Denmark)

    Quaglia, Alberto; Sin, Gürkan; Gani, Rafiqul

    2014-01-01

    The construction of a processing network is a corporate investment, that processing companies make with the goal of creating the conditions to increase their value. In a previous work, a computer-aided framework supporting the design of processing network under uncertainty has been presented...

  11. A Dialectic Analysis of Generativity: Issues of Network-Supported Design in Mathematics and Science

    Science.gov (United States)

    Stroup, Walter M.; Ares, Nancy M.; Hurford, Andrew C.

    2005-01-01

    New theoretical, methodological, and design frameworks for engaging classroom learning are supported by the highly interactive and group-centered capabilities of a new generation of classroom-based networks. In our analyses, networked teaching and learning are organized relative to a dialectic of (a) seeing mathematical and scientific structures…

  12. Cacti beginner's guide leverage cacti to design a robust network operations center

    CERN Document Server

    Urban, Thomas

    2017-01-01

    The book is designed in such a way that you can explore it chapter-by-chapter or skip any chapter without missing a beat. If you are a network operator and want to use Cacti for implementing performance measurement for trending, troubleshooting, and reporting purposes, then this book is for you. You only need to know the basics of network ...

  13. Design and application of link: A DSL for network frame manipulation

    CSIR Research Space (South Africa)

    Pennefather, S

    2017-08-01

    Full Text Available This paper describes the design and application of Link, a Domain Specific Language (DSL) targeting the development of network applications focused on traffic manipulation at the frame level. The development of Link is described through...

  14. A fuzzy multi-objective optimization model for sustainable reverse logistics network design

    DEFF Research Database (Denmark)

    Govindan, Kannan; Paam, Parichehr; Abtahi, Amir Reza

    2016-01-01

    Decreasing the environmental impact, increasing the degree of social responsibility, and considering the economic motivations of organizations are three significant features in designing a reverse logistics network under sustainability respects. Developing a model, which can simultaneously consid...

  15. Acceleration of solving the dynamic multi-objective network design problem using response surface methods

    NARCIS (Netherlands)

    Wismans, Luc Johannes Josephus; van Berkum, Eric C.; Bliemer, M.C.J.

    2014-01-01

    Optimization of externalities and accessibility using dynamic traffic management measures on a strategic level is a specific example of solving a multi-objective network design problem. Solving this optimization problem is time consuming, because heuristics like evolutionary multi objective

  16. Designing optimal peer support to alleviate learner cognitive load in Learning Networks

    NARCIS (Netherlands)

    Hsiao, Amy; Brouns, Francis; Sloep, Peter

    2012-01-01

    Hsiao, Y. P., Brouns, F., & Sloep, P. B. (2012, 21 July). Designing optimal peer support to alleviate learner cognitive load in Learning Networks. Presentation at IADIS International Conference Web-Based Communities and Social Media 2012, Lisbon, Portugal.

  17. Sustainable Queuing-Network Design for Airport Security Based on the Monte Carlo Method

    Directory of Open Access Journals (Sweden)

    Xiangqian Xu

    2018-01-01

    Full Text Available The design of airport queuing networks is a significant research field currently for researchers. Many factors must to be considered in order to achieve the optimized strategies, including the passenger flow volume, boarding time, and boarding order of passengers. Optimizing these factors lead to the sustainable development of the queuing network, which currently faces a few difficulties. In particular, the high variance in checkpoint lines can be extremely costly to passengers as they arrive unduly early or possibly miss their scheduled flights. In this article, the Monte Carlo method is used to design the queuing network so as to achieve sustainable development. Thereafter, a network diagram is used to determine the critical working point, and design a structurally and functionally sustainable network. Finally, a case study for a sustainable queuing-network design in the airport is conducted to verify the efficiency of the proposed model. Specifically, three sustainable queuing-network design solutions are proposed, all of which not only maintain the same standards of security, but also increase checkpoint throughput and reduce passenger waiting time variance.

  18. Unified Tractable Model for Large-Scale Networks Using Stochastic Geometry: Analysis and Design

    KAUST Repository

    Afify, Laila H.

    2016-12-01

    The ever-growing demands for wireless technologies necessitate the evolution of next generation wireless networks that fulfill the diverse wireless users requirements. However, upscaling existing wireless networks implies upscaling an intrinsic component in the wireless domain; the aggregate network interference. Being the main performance limiting factor, it becomes crucial to develop a rigorous analytical framework to accurately characterize the out-of-cell interference, to reap the benefits of emerging networks. Due to the different network setups and key performance indicators, it is essential to conduct a comprehensive study that unifies the various network configurations together with the different tangible performance metrics. In that regard, the focus of this thesis is to present a unified mathematical paradigm, based on Stochastic Geometry, for large-scale networks with different antenna/network configurations. By exploiting such a unified study, we propose an efficient automated network design strategy to satisfy the desired network objectives. First, this thesis studies the exact aggregate network interference characterization, by accounting for each of the interferers signals in the large-scale network. Second, we show that the information about the interferers symbols can be approximated via the Gaussian signaling approach. The developed mathematical model presents twofold analysis unification for uplink and downlink cellular networks literature. It aligns the tangible decoding error probability analysis with the abstract outage probability and ergodic rate analysis. Furthermore, it unifies the analysis for different antenna configurations, i.e., various multiple-input multiple-output (MIMO) systems. Accordingly, we propose a novel reliable network design strategy that is capable of appropriately adjusting the network parameters to meet desired design criteria. In addition, we discuss the diversity-multiplexing tradeoffs imposed by differently favored

  19. Using artificial neural networks in the design of orthotropic bridge decks

    Directory of Open Access Journals (Sweden)

    Ahmed Shamel Fahmy

    2016-12-01

    Full Text Available For orthotropic bridge decks a lot of progress has been made in the development of codes to aid in the design process, in addition to software tools for numerical analysis and design. However, professional software tools will not aid the designer in choosing a preliminary economic layout at the conceptual design stage. Designers would go through iterative, lengthy and expensive procedures to reach the best configuration. The present research provides a methodology to investigate the contingency of using artificial neural networks for conceptual design of orthotropic steel-deck bridge. A neural network model was trained with different combinations of dimensions, and eight types of safety checks were performed on all of them. The resulting network can predict whether the deck is safe or not. It is found that this approach for the selection of orthotropic deck dimensions is a better and cost-effective option compared with international codes or expert opinion.

  20. Internet of Things Heterogeneous Interoperable Network Architecture Design

    DEFF Research Database (Denmark)

    Bhalerao, Dipashree M.

    2014-01-01

    Internet of Thing‘s (IoT) state of the art deduce that there is no mature Internet of Things architecture available. Thesis contributes an abstract generic IoT system reference architecture development with specifications. Novelties of thesis are proposed solutions and implementations....... It is proved that reduction of data at a source will result in huge vertical scalability and indirectly horizontal also. Second non functional feature contributes in heterogeneous interoperable network architecture for constrained Things. To eliminate increasing number of gateways, Wi-Fi access point...... with Bluetooth, Zigbee (new access point is called as BZ-Fi) is proposed. Co-existence of Wi-Fi, Bluetooth, and Zigbee network technologies results in interference. To reduce the interference, orthogonal frequency division multiplexing (OFDM) is proposed tobe implemented in Bluetooth and Zigbee. The proposed...