WorldWideScience

Sample records for grit roughness legr

  1. Effects of grit roughness and pitch oscillations on the NACA 4415 airfoil

    Energy Technology Data Exchange (ETDEWEB)

    Hoffmann, M.J.; Reuss Ramsay, R.; Gregorek, G.M. [Ohio State Univ., Columbus, OH (United States)

    1996-07-01

    A NACA 4415 airfoil model was tested in The Ohio State University Aeronautical and Astronautical Research Laboratory 3 x 5 subsonic wind tunnel under steady state and unsteady conditions. The test defined baseline conditions for steady state angles of attack from {minus}10{degree} to +40{degree} and examined unsteady behavior by oscillating the model about its pitch axis for three mean angles, three frequencies, and two amplitudes. For all cases, Reynolds numbers of 0.75, 1, 1.25, and 1.5 million were used. In addition, these were repeated after the application of leading edge grit roughness (LEGR) to determine contamination effects on the airfoil performance. Steady state results of the NACA 4415 testing at Reynolds number of 1.25 million showed a baseline maximum lift coefficient of 1.30 at 12.3{degree} angle of attack. The application of LEGR reduced the maximum lift coefficient by 20% and increased the 0.0090 minimum drag coefficient value by 62%. The zero lift pitching moment of {minus}0.0967 showed a 13% reduction in magnitude to {minus}0.0842 with LEGR applied. Data were also obtained for two pitch oscillation amplitudes: {+-}5.5{degree} and {+-}10{degree}. The larger amplitude consistently gave a higher maximum lift coefficient than the smaller amplitude, and both unsteady maximum lift coefficients were greater than the steady state values. Stall is delayed on the airfoil while the angle of attack is increasing, thereby causing an increase in maximum lift coefficient. A hysteresis behavior was exhibited for all the unsteady test cases. The hysteresis loops were larger for the higher reduced frequencies and for the larger amplitude oscillations. As in the steady case, the effect of LEGR in the unsteady case was to reduce the lift coefficient at high angles of attack. In addition, with LEGR, the hysteresis behavior persisted into lower angles of attack than for the clean case.

  2. Effects of grit roughness and pitch oscillations on the S810 airfoil

    Energy Technology Data Exchange (ETDEWEB)

    Ramsay, R.R.; Hoffman, M.J.; Gregorek, G.M. [Ohio State Univ., Columbus, OH (United States)

    1996-01-01

    An S810 airfoil model was tested in The Ohio State University Aeronautical and Astronautical Research Laboratory 3 x 5 subsonic wind tunnel under steady state and unsteady conditions. The test defined baseline conditions for steady state angles of attack from -20{degrees} to +40{degrees} and examined unsteady behavior by oscillating the model about its pitch axis for three mean angles, three frequencies, and two amplitudes. For all cases, Reynolds numbers of 0.75, 1, 1.25, and 1.5 million were used. In addition, the above conditions were repeated after the application of leading edge grit roughness (LEGR) to determine contamination effects on the airfoil performance. Baseline steady state results of the S810 testing showed a maximum lift coefficient of 1.15 at 15.2{degrees}angle of attack. The application of LEGR reduced the maximum lift coefficient by 12% and increased the 0.0085 minimum drag coefficient value by 88%. The zero lift pitching moment of -0.0286 showed a 16% reduction in magnitude to -0.0241 with LEGR applied. Data were also obtained for two pitch oscillation amplitudes: {plus_minus}5.5{degrees} and {plus_minus}10{degrees}. The larger amplitude consistently gave a higher maximum lift coefficient than the smaller amplitude and both sets of unsteady maximum lift coefficients were greater than the steady state values. Stall was delayed on the airfoil while the angle of attack was increasing, thereby causing an increase in maximum lift coefficient. A hysteresis behavior was exhibited for all the unsteady test cases. The hysteresis loops were larger for the higher reduced frequencies and for the larger amplitude oscillations. In addition to the hysteresis behavior, an unusual feature of these data were a sudden increase in the lift coefficient where the onset of stall was expected. As in the steady case, the effect of LEGR in the unsteady case was to reduce the lift coefficient at high angles of attack.

  3. Effects of grit roughness and pitch oscillations on the S814 airfoil

    Energy Technology Data Exchange (ETDEWEB)

    Janiszewska, J.M.; Ramsay, R.R.; Hoffmann, M.J.; Gregorek, G.M. [Ohio State Univ., Columbus, OH (United States)

    1996-07-01

    Horizontal-axis wind turbine rotors experience unsteady aerodynamics when the rotor is yawed, when rotor blades pass through the support tower wake, and when the wind is gusting. An understanding of this unsteady behavior is necessary to assist in the design of new rotor airfoils. The rotors also experience performance degradation due to surface roughness. These surface irregularities are due to the accumulation of insect debris, ice, and/or the aging process. Wind tunnel studies that examine both the steady and unsteady behavior of airfoils can help define pertinent flow phenomena, and the resultant data can also be used to validate analytical computer codes. An S814 airfoil model was tested in The Ohio State University Aeronautical and Astronautical Research Laboratory (OSU/AARL) 3 X 5 subsonic wind tunnel (3 X 5) under steady flow with both stationary model conditions and pitch oscillations. To study the extent of performance loss due to surface roughness, a leading edge grit roughness pattern (LEGR) was used to simulate leading edge contamination. After baseline cases were completed, the LEGR was applied for both steady state and model pitch oscillation cases. The Reynolds numbers for steady state conditions were 0.75, 1, 1.25 and 1.5 million, while the angle of attack ranged from -20{degrees} to +40{degrees}. While the model underwent pitch oscillations, data were acquired at Reynolds numbers of 0.75, 1, 1.25, and 1.5 million, at frequencies of 0.6, 1.2, and 1.8 Hz. Two sine wave forcing functions {+-}5.5{degrees} and {+-}10{degrees}, were used; at mean angles of attack of 8{degrees}, 14{degrees}, and 20{degrees}. For purposes herein, any reference to unsteady conditions means the model was in pitch oscillation.

  4. Effects of grit roughness and pitch oscillations on the LS(1)-0417MOD airfoil

    Energy Technology Data Exchange (ETDEWEB)

    Janiszewska, J.M.; Ramsay, R.R.; Hoffman, M.J.; Gregorek, G.M. [Ohio State Univ., Columbus, OH (United States)

    1996-01-01

    Horizontal axis wind turbine rotors experience unsteady aerodynamics due to wind shear when the rotor is yawed, when rotor blades pass through the support tower wake, and when the wind is gusting. An understanding of this unsteady behavior is necessary to assist in the calculations of rotor performance and loads. The rotors also experience performance degradation caused by surface roughness. These surface irregularities are due to the accumulation of insect debris, ice, and/or the aging process. Wind tunnel studies that examine both the steady and unsteady behavior of airfoils can help define pertinent flow phenomena, and the resultant data can be used to validate analytical computer codes. An LS(l)-0417MOD airfoil model was tested in The Ohio State University Aeronautical and Astronautical Research Laboratory (OSU/AARL) 3{times}5 subsonic wind tunnel (3{times}5) under steady flow and stationary model conditions, as well as with the model undergoing pitch oscillations. To study the possible extent of performance loss due to surface roughness, a standard grit pattern (LEGR) was used to simulate leading edge contamination. After baseline cases were completed, the LEGR was applied for both steady state and model pitch oscillation cases. The Reynolds numbers for steady state conditions were 0.75, 1, 1.25, and 1.5 million, while the angle of attack ranged from {minus}20{degrees} to +40{degrees}. With the model undergoing pitch oscillations, data were acquired at Reynolds numbers of 0.75, 1, 1.25, and 1.5 million, at frequencies of 0.6, 1.2, and 1.8 Hz. Two sine wave forcing functions were used, {plus_minus} 5.5%{degrees} and {plus_minus} 10{degrees}, at mean angles of attack of 8{degrees}, 14{degrees}, and 20{degrees}. For purposes herein, any reference to unsteady conditions foil model was in pitch oscillation about the quarter chord.

  5. Effects of grit roughness and pitch oscillations on the LS(1)-0421MOD airfoil

    Energy Technology Data Exchange (ETDEWEB)

    Reuss, R.L.; HOffman, M.J.; Gregorek, G.M. [Ohio State Univ., Columbus, OH (United States)

    1995-12-01

    An LS(1)-0421 MOD airfoil model was tested in The Ohio State University Aeronautical and Astronautical Research Laboratory (OSU/AARL) 3{times}5 subsonic wind tunnel (3{times}5) under steady flow and stationary model conditions, and also with the model undergoing pitch oscillations. In order to study the possible extent of performance loss due to surface roughness, a leading edge grit roughness (LEGR) pattern was developed to simulate leading edge contamination. After baseline cases were completed, the LEGR was applied for both steady state and model pitch oscillation cases. The Reynolds numbers for steady state conditions were 0.75, 1, and 1.25 million, while the angle of attack ranged from {minus}10{degrees} to +40{degrees}. With the model undergoing pitch oscillations, data was acquired at Reynolds numbers of 0.75, 1, 1.25, and 1.5 million, at frequencies of 0.6, 1.2, and 1.8 Hz. Two sine wave forcing functions were used; {plus_minus} 5.5{degrees} and {plus_minus} 10{degrees}, at mean angles of attack of 8{degrees}, 14{degrees}, and 20{degrees}. For this report, unsteady conditions refer to the model in pitch oscillation. In general, the maximum unsteady lift coefficient was from 10% to 50% higher than the steady state maximum lift coefficient. Variation in the quarter chord pitching moment coefficient was nearly two times greater than steady state values at high angles of attack. These findings indicate the importance of considering the unsteady flow behavior occurring in wind turbine operation for accurate load estimates.

  6. Effects of grit roughness and pitch oscillations on the S801 airfoil

    Energy Technology Data Exchange (ETDEWEB)

    Ramsay, R.R.; Hoffman, M.J.; Gregorek, G.M. [Ohio State Univ., Columbus, OH (United States)

    1996-01-01

    Horizontal axis wind turbine rotors experience unsteady aerodynamics due to wind shear when the rotor is yawed, when rotor blades pass through the support tower wake, and when the wind is gusting. An understanding of this unsteady behavior is necessary to assist in the calculation of rotor performance and loads. The rotors also experience performance degradation due to surface roughness. These surface irregularities are due to the accumulation of insect debris, ice, and the aging process. Wind tunnel studies that examine both the steady and unsteady behavior of airfoils can help define pertinent flow phenomena, and the resultant data can be used to validate analytical computer codes. A S801 airfoil model was tested in The Ohio State University Aeronautical and Astronautical Research Laboratory (OSU/AARL) 3x5 subsonic wind tunnel (3x5) under steady flow and stationary model conditions, as well as with the model undergoing pitch oscillations. To study the possible extent of performance loss due to surface roughness, a standard grit pattern (LEGR) was used to simulate leading edge contamination. After baseline cases were completed, the LEGR was applied for both steady state and model pitch oscillation cases. The Reynolds numbers used for steady state conditions were 0.75, 1, 1.25, and 1.5 million, while the angle of attack ranged from -20{degrees} to +40{degrees}. With the model undergoing pitch oscillations, data were acquired at Reynolds numbers of 0.75, 1, 1.25, and 1.4 million, at frequencies of 0.6, 1.2, and 1.8 Hz. Two sine wave forcing functions were used, {plus_minus} 5.5 {degrees}and {plus_minus} 10{degrees}, at mean angles of attack of 8{degrees} 14{degrees} and 20{degrees} For purposes herein, any reference to unsteady conditions means that the airfoil model was in pitch oscillation about the quarter chord.

  7. Effects of grit roughness and pitch oscillations on the S815 airfoil

    Energy Technology Data Exchange (ETDEWEB)

    Reuss Ramsay, R.; Hoffman, M.J.; Gregorek, G.M. [Ohio State Univ., Columbus, OH (United States)

    1996-07-01

    Horizontal axis wind turbine rotors experience unsteady aerodynamics due to wind shear when the rotor is yawed, when rotor blades pass through the support tower wake, and when the wind is gusting. An understanding of this unsteady behavior is necessary to assist in the calculation of rotor performance and loads. The rotors also experience performance degradation due to surface roughness. These surface irregularities are cause by the accumulation of insect debris, ice, and the aging process. Wind tunnel studies that examine both the steady and unsteady behavior of airfoils can help define pertinent flow phenomena, and the resultant data can be used to validate analytical computer codes. A S815 airfoil model was tested in The Ohio State University Aeronautical and Astronautical Research Laboratory (OSU/AARL) 3 x 5 subsonic wind tunnel (3 x 5) under steady flow and stationary model conditions, as well as with the model undergoing pitch oscillations. To study the possible extent of performance loss due to surface roughness, a standard grit pattern (LEGR) was used to simulate leading edge contamination. After baseline cases were completed, the LEGR was applied for both steady state and model pitch oscillation cases. The Reynolds numbers used for steady state conditions were 0.75, 1, 1.25, and 1.4 million, while the angle of attack ranged from {minus}20{degree} to +40{degree}. With the model undergoing pitch oscillations, data were acquired at Reynolds numbers of 0.75, 1, 1.25, and 1.4 million, at frequencies of 0.6, 1.2, and 1.8 Hz. Two sine wave forcing functions were used; {+-}5.5{degree} and {+-}10{degree}, at mean angles of attack of 8{degree}, 14{degree}, and 20{degree}. For purposes herein, any reference to unsteady conditions means that the model was in pitch oscillation about the quarter chord.

  8. Effects of grit roughness and pitch oscillations on the S809 airfoil

    Energy Technology Data Exchange (ETDEWEB)

    Ramsay, R.F.; Hoffman, M.J.; Gregorek, G.M. [Ohio State Univ., Columbus, OH (United States)

    1995-12-01

    An S809 airfoil model was tested in The Ohio State University Aeronautical and Astronautical Research Laboratory (OSU/AARL) 3{times}5 subsonic wind tunnel (3{times}5) under steady flow and stationary model conditions, and also with the model undergoing pitch oscillations. To study the possible extent of performance loss due to surface roughness, a standard grit pattern (LEGR) was developed to simulate leading edge contamination. After baseline cases were completed, the LEGR was applied for both steady state and model pitch oscillation cases. The Reynolds numbers for steady state conditions were 0.75, 1, 1.25, and 1.5 million, while the angle of attack ranged from {minus}20, to +40 {degrees}. With the model undergoing pitch oscillations, data were acquired at Reynolds numbers of 0.75, 1, 1.25, and 1.4 million, at frequencies of 0.6, 1.2, and 1.8 Hz. Two sine wave forcing functions were used; {plus_minus} 5.5{degrees} and {plus_minus} 10{degrees}, at mean angles of attack of 8{degrees}, 14{degrees}, and 20{degrees}. For purposes herein, any reference to unsteady conditions means the model was in pitch oscillation about the quarter chord. In general, the unsteady maximum lift coefficient was from 4% to 86% higher than the steady state maximum lift coefficient, and variation in the quarter chord pitching moment coefficient magnitude was from {minus}83% to 195% relative to steady state values at high angles of attack. These findings indicate the importance of considering the unsteady flow behavior occurring in wind turbine operation to obtain accurate load estimates.

  9. Kortlægning af ålegræsenge med ortofotos

    DEFF Research Database (Denmark)

    Bachmann Ørberg, Sarah; Groom, Geoffrey Brian; Kjeldgaard, Ane

    Kort over ålegræssets udbredelse er vigtige for optimal forvaltning af ålegræsenge og bidrager også til synergi mellem f.eks. Vandrammedirektivet, der inddrager ålegræs som indikator for god økologisk tilstand, og Fuglebeskyttelsesdirektivet, der har fokus på ålegræs som føde for vandfugle og der...

  10. Effects of surface roughness and vortex generators on the NACA 4415 airfoil

    Energy Technology Data Exchange (ETDEWEB)

    Reuss, R.L.; Hoffman, M.J.; Gregorek, G.M. [Ohio State Univ., Columbus, OH (United States)

    1995-12-01

    Wind turbines in the field can be subjected to many and varying wind conditions, including high winds with rotor locked or with yaw excursions. In some cases the rotor blades may be subjected to unusually large angles of attack that possibly result in unexpected loads and deflections. To better understand loadings at unusual angles of attack, a wind tunnel test was performed. An 18-inch constant chord model of the NACA 4415 airfoil section was tested under two dimensional steady state conditions in the Ohio State University Aeronautical and Astronautical Research Laboratory (OSU/AARL) 7 x 10 Subsonic Wind Tunnel (7 x 10). The objective of these tests was to document section lift and moment characteristics under various model and air flow conditions. These included a normal angle of attack range of {minus}20{degree} to +40{degree}, an extended angle of attack range of {minus}60{degree} to +230{degree}, applications of leading edge grit roughness (LEGR), and use of vortex generators (VGs), all at chord Reynolds numbers as high as possible for the particular model configuration. To realistically satisfy these conditions the 7 x 10 offered a tunnel-height-to-model-chord ratio of 6.7, suggesting low interference effects even at the relatively high lift and drag conditions expected during the test. Significantly, it also provided chord Reynolds numbers up to 2.0 million. 167 figs., 13 tabs.

  11. Got Grit? Maybe…

    Science.gov (United States)

    Duckor, Brent

    2017-01-01

    The constructs that currently animate today's dispositions movement are grit and growth mindset. However, the evidence for the reliability and instructional uses of such noncognitive factors in K-12 schools--and of the surveys and tools that attempt to measure them--is thin. After a look at the "logic of assessment" with its focus on…

  12. Sæsontilpasninger i stofsikftet reducerer lyskravet hos ålegræs (Zostera marina)

    DEFF Research Database (Denmark)

    Stæhr, Peter A.; Borum, Jens

    temperaturer for respiration og fotosyntese hos sommertilpassede planter (5oC og 2o C højere, respektivt). Ved lave og høje temperaturer var metabolisme raterne dog nedsatte i fht vintertilpassede planter. Respirationen var generelt mere følsom end fotosyntesen over for stigende temperaturer, især...... stigende temperaturer, særligt udtalt for vintertilpassede planter. Modeller af EC som funktion af temperaturen for hele planter, blev sammenholdt med data for daglig lys tilgængelighed. Dette viste at de relativt beskedne sæsonbetingede tilpasninger i stofskiftet hos ålegræs var tilstrækkelige til...... beregnet under forskellige kombinationer af sommer temperaturer og lyssvækkelse i vandsøjlen, viste at en forventet temperaturstigning på 5oC har markant mindre betydning for den maksimale dybdeudbredelse af ålegræs end relativt små forringelser i planternes lystilgængelighed. Kombinationen af varmere...

  13. Effect of the bur grit size on the flexural strength of a glass-ceramic

    Directory of Open Access Journals (Sweden)

    P. P. Kist

    Full Text Available Abstract The purpose of the present study was to determine the biaxial flexural strength (BFS of a CAD/CAM leucite reinforced glass-ceramic ground by diamond burs of different grit sizes and the influence of surface roughness on the BFS. For this, 104 plates were obtained from CAD/CAM ceramic blocks and divided into 4 groups (n = 26, according to bur grit size: extra-fine, fine, medium and coarse. Roughness parameters (Ra, RyMax were measured, and plates were kept dry for 7 days. The flexural test was carried out and BFS was calculated. Ra, RyMax and BFS data were subjected to analysis of variance and post-hoc test. Weibull analysis was used to compare characteristic strength and Weibull modulus. Regression analysis was performed for BFS vs. Ra and RyMax. When burs with coarse grit were used, higher surface roughness values were found, causing a negative effect on the ceramic BFS (117 MPa for extra-fine, and 83 MPa for coarse. Correlation (r between surface roughness and BFS was 0.78 for RyMax and 0.73 for Ra. Increases in diamond grit size have a significant negative effect on the BFS of leucite-reinforced glass-ceramics, suggesting that grinding of sintered glass-ceramic should be performed using burs with the finest grit possible in order to minimize internal surface flaws and maximize flexural strength.

  14. Effect of the bur grit size on the flexural strength of a glass-ceramic

    OpenAIRE

    Kist, P. P.; Aurélio, I. L.; Amaral, M.; May, L. G.

    2016-01-01

    Abstract The purpose of the present study was to determine the biaxial flexural strength (BFS) of a CAD/CAM leucite reinforced glass-ceramic ground by diamond burs of different grit sizes and the influence of surface roughness on the BFS. For this, 104 plates were obtained from CAD/CAM ceramic blocks and divided into 4 groups (n = 26), according to bur grit size: extra-fine, fine, medium and coarse. Roughness parameters (Ra, RyMax) were measured, and plates were kept dry for 7 days. The flexu...

  15. Grit Trumps Talent? An experimental approach

    DEFF Research Database (Denmark)

    Gerhards, Leonie; Gravert, Christina Annette

    Perseverance to accomplish long-term goals, also know as grit, is a crucial determinant for success in life. In the present study we introduce an innovative laboratory design to elicit grit in an incentivized and controlled way. Subjects work on a computerized task to solve anagrams. By observing...

  16. Grit: An important characteristic in learners.

    Science.gov (United States)

    Hammond, Drayton A

    Grit, or the perseverance and passion for long-term goals, has been associated with successful pursuits in academics, competitions, and professions outside of pharmacy. The fortitude needed to withstand tremendous physical, mental, and emotional stressors may be better predicted by grit than other factors. In those who demonstrate grit, a combination of factors may reflect academic achievement. It appears that achievement results when talent and effort are combined, with particular attention being paid to effort, as it is a function of the direction, duration, and intensity of a person's actions toward a goal. It appears that grit may be a good discriminating factor when evaluating individuals in other professions. The objective of this short commentary is to provide an introduction to the non-pharmacy literature surrounding grit and to suggest its applications in pharmacy. Copyright © 2016 Elsevier Inc. All rights reserved.

  17. Glycaemic Response to Quality Protein Maize Grits

    Directory of Open Access Journals (Sweden)

    Leonora N. Panlasigui

    2010-01-01

    Full Text Available Background. Carbohydrates have varied rates of digestion and absorption that induces different hormonal and metabolic responses in the body. Given the abundance of carbohydrate sources in the Philippines, the determination of the glycaemic index (GI of local foods may prove beneficial in promoting health and decreasing the risk of diabetes in the country. Methods. The GI of Quality Protein Maize (QPM grits, milled rice, and the mixture of these two food items were determined in ten female subjects. Using a randomized crossover design, the control bread and three test foods were given on separate occasions after an overnight fast. Blood samples were collected through finger prick at time intervals of 0, 15, 30, 45, 60, 90, and 120 min and analyzed for glucose concentrations. Results. The computed incremental area under the glucose response curve (IAUC varies significantly across test foods (P<.0379 with the pure QPM grits yielding the lowest IAUC relative to the control by 46.38. Resulting GI values of the test foods (bootstrapped were 80.36 (SEM 14.24, 119.78 (SEM 18.81, and 93.17 (SEM 27.27 for pure QPM grits, milled rice, and rice-QPM grits mixture, respectively. Conclusion. Pure QPM corn grits has a lower glycaemic response compared to milled rice and the rice-corn grits mixture, which may be related in part to differences in their dietary fibre composition and physicochemical characteristics. Pure QPM corn grits may be a more health beneficial food for diabetic and hyperlipidemic individuals.

  18. Economic Analysis of the Greenland Inland Traverse (GrIT)

    Science.gov (United States)

    2016-06-01

    fuel and cargo based on data from the 2012 and 2014 seasons. DISCLAIMER: The contents of this report are not to be used for advertising ...GrIT compared with airlift ....................................................................... 24 13 Fuel consumed by GrIT12 and GrIT14 compared...objective was to identify and quantify, insofar as possible, the component costs of the GrIT and airlift resupply modes. In effect , we sought to link

  19. A Genealogy of Grit: Education in the New Gilded Age

    Science.gov (United States)

    Stokas, Ariana Gonzalez

    2015-01-01

    Recently, due in part to the research of Angela Duckworth, the cultivation of dispositions in education, grit in particular, has gained the attention of educational policymakers and the educational research community. While much of the research has focused on how to detect grit, there has been little discussion regarding how grit came to be valued…

  20. Recycling of paint-contaminated grit.

    Science.gov (United States)

    Taha, R; al-Alawi, D; al-Nabhani, M; Pillay, A E; al-Hamdi, A

    2001-08-01

    The impact on the environment of using paint-contaminated grit (PCG) as a partial or full replacement for sand in Portland cement mortar and asphalt concrete mixtures was investigated. The grit waste material originated from abrasive blasting of offshore steel structures. There is a major environmental concern regarding the safe disposal of the spent blasting abrasives that contain paint chips or paint particles and other debris removed from the surface of the steel structures. This work investigated the potential reuse of PCG in Portland cement concrete (PCC) and hot mix asphalt concrete. Several studies were conducted to establish the integrity of the materials containing the recycled grit. These included the chemical and physical characterization of natural sand and PCG, the assay of leaches associated with the grit material for hazardous metal contaminants, such as Cr, Cd and Pb, and the assessment of the mechanical properties of the PCG-substituted mortars by applying special tests (such as Marshall stability and determination of the flow properties) to the PCG-substituted asphalt concrete mixtures. The overall results demonstrated that the potential reuse of PCG in PCC and asphalt concrete mixtures would not pose any environmental threat and could produce several benefits, such as reduced disposal costs, protection of water sources from improper disposal practices and reduced costs in the production of natural aggregates and asphalt cement.

  1. Grit, anxiety, and stress in emergency physicians.

    Science.gov (United States)

    Wong, Matthew L; Anderson, Jared; Knorr, Thomas; Joseph, Joshua W; Sanchez, Leon D

    2018-02-26

    The personality traits of emergency physicians are infrequently studied, though interest in physician wellness is increasing. The objective of this study is to acquire pilot data about the amount of grit, anxiety, and stress in emergency physicians using established psychological survey instruments, and to examine their associations of each of these traits with each other. Thirty-six emergency medicine resident and attending physicians from an urban academic medical center consented for enrollment. Participants were administered the Duckworth 12-point Grit Scale, the State-Trait Anxiety Inventory (STAI), and the Perceived Stress Scale (PSS), which measure grit, anxiousness, and perceived stress, respectively. These are the gold standard psychological instruments for each of their areas. We analyzed the results with descriptive statistics, Spearman correlations, and linear regression. Nineteen residents and 17 attending physicians completed the surveys during the first quarter of a new academic year. The mean grit score was 3.7 (95% CI 3.5-3.8, SD: 0.56), the mean trait-anxiety score was 32.61 (95% CI 30.15-35.07, SD: 7.26), and the mean PSS score was 12.28 (95% CI 10.58-13.97, SD: 4.99). Only trait-anxiety and perceived stress were significantly correlated (Spearman's rho: 0.70, panxious reported more stress. Levels of grit were not associated with trait-anxiety. These psychological concepts should be studied further as they relate to the function and health of emergency medicine providers. Copyright © 2018. Published by Elsevier Inc.

  2. Review of Grit and Resilience Literature within Health Professions Education

    Science.gov (United States)

    Cain, Jeff

    2018-01-01

    Objective. To review literature pertaining to grit and resilience in health professions education. Findings. There is significant interest in grit and resilience throughout the health professions, but little has been published with regard to pharmacy. Although there are methodological issues with defining and measuring grit and resilience, several studies have shown relationships between the constructs and personal and academic well-being. Educational interventions aimed at increasing grit and resilience have produced mixed results. Developing protective factors appears to be the most common approach in helping students become more resilient. Summary. Literature pertaining to grit and resilience reveals that the terms are nuanced, complex, and difficult to measure and understand. Regardless, the general characteristics associated with grit and resilience are of interest to educators and warrant further study. PMID:29606705

  3. Army Grit: Field Marshal Viscount Slims Key to Victory

    Science.gov (United States)

    2017-05-25

    24 Part Two: The Education of a Grit Paragon...Damon is a professor of psychology at Stanford Graduate School of Education ; and Duckworth, Grit: The Power of Passion and Perseverance, 91. . 8 The...visitors from the fighting troops, especially those who interfered with the pleasant tenor of staff life, were not really welcome.”84 Later in his career

  4. Personality and Family Context in Explaining Grit of Taiwanese High School Students

    Science.gov (United States)

    Lin, Che-Li; Chang, Chun-Yen

    2017-01-01

    Grit, one of the newly developed non-cognitive traits, encompasses the characteristics of perseverance and consistency of interest. Grit is associated with good academic performance, resilience, and well-being. To understand the nature of Grit in detail, this study probed the relationship between Grit and the widely-applied and well-established…

  5. Properties of extruded snacks supplemented with amaranth grain grits

    Directory of Open Access Journals (Sweden)

    Hadnađev Miroslav S.

    2009-01-01

    Full Text Available Extruded amaranth grain products have specific aroma and can be used as snack food, supplement in breakfast cereals, or as raw material for further processing. Extruded products of corn-amaranth grits blends, containing 20% or 50% amaranth grain grits, were produced by extrusion-cooking using a laboratory Brabender single screw extruder 20 DN. Extrudates with various texture were obtained. During extrusion process starch granules are partially degraded, hence rheological properties were examined. All samples exhibited thixotropic flow behavior. Those samples in which part of the corn grits was replaced with amaranth one had lower viscosity and exhibited lower level of structuration during storage.

  6. Physical Fitness, Grit, School Attendance, and Academic Performance among Adolescents.

    Science.gov (United States)

    Cosgrove, Jonathan M; Chen, Yen T; Castelli, Darla M

    2018-01-01

    The purpose of this study was to examine the relationship of grit as a construct representing perseverance to overcoming barriers and the total number of school absences to academic performance (AP) while controlling for sociodemographics, fitness (i.e., PACER), and Body Mass Index (BMI). Adolescents ( N = 397, SD = 1.85; 80.9% females; 77.1% Hispanic) from an urban, minority-majority city in the Southern United States completed the FitnessGram® assessment of physical fitness (e.g., aerobic capacity and Body Mass Index (BMI)) and the valid and reliable short grit survey. The schools provided sociodemographics, attendance, and AP data for the adolescents. Adolescents with higher grit scores ( r s = 0.21, P < 0.001) and less total absences ( r s = -0.35, P < 0.001) performed better on AP. Hierarchical multiple regression indicated that grit and absences were associated with AP ( β = 0.13, P < 0.01 and β = -0.35, P < 0.001, resp.). Grit and a total number of absences are significant contributors to academic success, particularly among Hispanic adolescents. Further, grit and school attendance may serve as a better measure of protective factors over proximal health measures of cardiovascular health and BMI.

  7. Diallel analysis of corn for special use as corn grits: determining the main genetic effects for corn gritting ability.

    Science.gov (United States)

    Conrado, T V; Scapim, C A; Bignotto, L S; Pinto, R J B; Freitas, I L J; Amaral, A T; Pinheiro, A C

    2014-08-26

    Corn grits are used for various purposes such as flakes, snacks, livestock feed, hominy, extruded products, beer, etc. The grit size proportion varies according to the hybrid, and thus, once the use of the grits is linked to the particle size, determining the genetic effects is essential to develop hybrids for any specific use. For this purpose a complete diallel series of crosses, involving eight parents, was performed near Maringá, PR, Brazil. The objective of this study was to evaluate the general (GCA) and specific (SCA) combining abilities of 28 progeny for selection of hybrids for breeding programs and extraction of inbred lines for hybrid development. The response variables, such as plant height, ear insertion height, crop stand, grain yield, and grits, small grits and bran production, were gauged and appraised for each of the 28 progeny. The trait effects and GCA were significant for all response variables, while for SCA, only grain yield and crop stand showed significance (P < 0.05), according to Griffing (1955) analysis. A significant weak negative partial correlation was found between grain yield and grits conversion. In relation to the hybrid selection for breeding programs, the parent IAC Nelore was highly recommended for recurrent selection and the hybrids IPR 119 x HT 392 and IAC Nelore x HD 332 for the extraction of pure lines for hybrid development.

  8. Influence of surface roughness of stainless steel on microbial adhesion and corrosion resistance

    DEFF Research Database (Denmark)

    Hilbert, Lisbeth Rischel; Bagge-Ravn, Dorthe; Kold, John

    2003-01-01

    Abstract The aim of this study was to evaluate if hygienic characteristics of stainless steel used in the food industry could be improved by smoothing surface roughness from an Ra of 0.9 to 0.01 ƒÝm. The adherence of Pseudomonas sp., Listeria monocytogenes and Candida lipolytica to stainless steel...... was not affected by surface roughness (Ra) ranging from grit 4000 polished stainless steel (Ra steel (Ra 0.9). Neither adhesion of Ps. aeruginosa nor its removal by an alkaline commercial cleaner in a flow system was affected by surface roughness. Pitting corrosion resistance...... was evaluated in a commercial disinfectant and in 1 M NaCl. Electropolished and grit 4000 polished steel proved more corrosion resistant as opposed to grit 80 and 120 polished surfaces. In conclusion, the surface finish did not influence bacterial attachment, colonisation, or removal, but is an important...

  9. The Gritty: Grit and Non-traditional Doctoral Student Success

    Directory of Open Access Journals (Sweden)

    Ted M. Cross

    2014-07-01

    Full Text Available As higher education is changing to reach larger numbers of students via online modalities, the issue of student attrition and other measures of student success become increasingly important. While research has focused largely on undergraduate online students, less has been done in the area of online non-traditional doctoral student success, particularly from the student trait perspective. The concept of grit, passion and persistence for long-term goals, has been identified as an important element of the successful attainment of long-term goals. As doctoral education is a long-term goal the purpose of this study was to examine the impact of doctoral student grit scores on student success. Success was measured by examining current student GPA and other factors. Significant relationships were found between grit and current student GPA, grit and the average number of hours students spent on their program of study weekly, and grit and age. The results of this research maybe important for informing how doctoral education is structured and how students might be better prepared for doctoral work.

  10. Characterization and evaluation of residue 'grits' of the cellulose industry

    International Nuclear Information System (INIS)

    Destefani, A.Z.; Santos, M.M.; Holanda, J.N.F.

    2010-01-01

    The cellulose industry generates huge amounts of solid waste residue called 'grits'. These wastes have been willing over time in landfills near the mills. However, this type of disposal is not environmentally friendly and can cause degradation and environmental pollution. In addition, environmental legislation increasingly severe and the high costs of landfill have led the search for new alternatives for final disposition of this abundant waste. In this context, this study is to characterize waste grits, generated by the cellulose industry in the region of Aracruz-ES. The residue samples were characterized in terms of chemical composition, X-ray diffraction, particle size distribution and thermal analysis (DTA and TGA). The characterization of the residual 'grits' demonstrated its potential as a feedstock for production of soil-cement bricks. (author)

  11. Colour characteristics of winter wheat grits of different grain size

    Directory of Open Access Journals (Sweden)

    Horváth Zs. H.

    2015-01-01

    Full Text Available Nowadays, wheat has spread all over the world due to its extensive usability. The colour of wheat grits is very important for the milling and baking industry because it determines the colour of the products made from it. The instrumental colour measuring is used, first of all, for durum wheat. We investigated the relationship between colour characteristics and grain size in the case of different hard aestivum wheats. We determined the colour using the CIE (Commission Internationale de l’Eclairage 1976 L*, a*, b* colour system measured by MINOLTA CR-300 tristimulus colorimeter. After screening the colour of the wheat fractions of different grain size, grits was measured wet and dry. We determined the L*, a*, b* colour co-ordinates and the whiteness index, too. To evaluate the values we had obtained, we used analysis of variance and regression analysis. We pointed out that the colour of wheat grits of different grain size is dependent on the hardness index of wheat. The lightness co-ordinate (L* of grits of the harder wheat is smaller, while a* and b* co-ordinates are higher. We also found that while grain size rises, the L* co-ordinate decreases and a*, b* values increase in the case of every type of wheat. The colour of grits is determined by the colour of fractions of 250-400 μm in size, independently from the average grain size. The whiteness index and the L* colour co-ordinate have a linear relation (R2 = 0.9151; so, the determination of whiteness index is not necessary. The L* value right characterizes the whiteness of grits.

  12. The age of the Takatika Grit, Chatham Islands, New Zealand

    NARCIS (Netherlands)

    Hollis, Christopher J.; Stickley, Catherine E.; Bijl, Peter K.; Schiøler, Poul; Clowes, Christopher D.; Li, Xun; Campbell, Hamish

    2017-01-01

    The oldest Paleogene strata on Chatham Islands, east of New Zealand, are the phosphatized conglomerates and sandstones of the Takatika Grit that crops out on the northeastern coast at Tioriori and unconformably overlies the Chatham Schist. An intact Cretaceous–Paleogene boundary transition is not

  13. Rough Finite State Automata and Rough Languages

    Science.gov (United States)

    Arulprakasam, R.; Perumal, R.; Radhakrishnan, M.; Dare, V. R.

    2018-04-01

    Sumita Basu [1, 2] recently introduced the concept of a rough finite state (semi)automaton, rough grammar and rough languages. Motivated by the work of [1, 2], in this paper, we investigate some closure properties of rough regular languages and establish the equivalence between the classes of rough languages generated by rough grammar and the classes of rough regular languages accepted by rough finite automaton.

  14. Effects of surface roughness and vortex generators on the LS(1)-0417MOD airfoil

    Energy Technology Data Exchange (ETDEWEB)

    Reuss, R.L.; Hoffman, M.J.; Gregorek, G.M. [Ohio State Univ., Columbus, OH (United States)

    1995-12-01

    An 18-inch constant-chord model of the LS(l)-0417MOD airfoil section was tested under two dimensional steady state conditions ate University 7{times}10 Subsonic Wind Tunnel. The objective was to document section lift and moment characteristics model and air flow conditions. Surface pressure data was acquired at {minus}60{degrees} through + 230{degrees} geometric angles of attack, at a nominal 1 million Reynolds number. Cases with and without leading edge grit roughness were investigated. The leading edge mulated blade conditions in the field. Additionally, surface pressure data were acquired for Reynolds numbers of 1.5 and 2.0 million, with and without leading edge grit roughness; the angle of attack was limited to a {minus}20{degrees} to 40{degrees} range. In general, results showed lift curve slope sensitivities to Reynolds number and roughness. The maximum lift coefficient was reduced as much as 29% by leading edge roughness. Moment coefficient showed little sensitivity to roughness beyond 50{degrees} angle of attack, but the expected decambering effect of a thicker boundary layer with roughness did show at lower angles. Tests were also conducted with vortex generators located at the 30% chord location on the upper surface only, at 1 and 1.5 million Reynolds numbers, with and without leading edge grit roughness. In general, with leading edge grit roughness applied, the vortex generators restored 85 percent of the baseline level of maximum lift coefficient but with a more sudden stall break and at a higher angle of attack than the baseline.

  15. L'intégrité au CERN

    CERN Document Server

    HR, Department

    2015-01-01

    Pour mener à bien sa mission, le CERN compte sur la confiance et le soutien matériel de ses États membres et de ses partenaires, et se doit de gérer de manière exemplaire les ressources qui lui sont confiées. Dès lors, le CERN attend la plus haute intégrité de la part de tous ses collaborateurs (membres du personnel, consultants, contractants travaillant sur le domaine ou personne engagée à tout autre titre au CERN ou pour le compte de celui-ci). L’intégrité est l’une des valeurs essentielles du CERN. Elle est définie dans le Code de conduite comme le fait d’« agir avec éthique, en toute honnêteté intellectuelle et en étant responsable de ses actes ».

  16. Earth Construction and Landfill Disposal Options for Slaker Grits

    OpenAIRE

    Risto Pöykiö; G. Watkins; H. Nurmesniemi and O. Dahl

    2010-01-01

    Slaker grits, an industrial residue originating from the chemical recovery process at sulfate (kraft) pulp mills, are typically disposed of to landfill in Finland. However, due to the relatively low total heavy metal and low leachable heavy metal, chloride, fluoride, sulfate, Dissolved O rganic Carbon (DOC) and Total Dissolved Solids (TDS) concentrations, the residue is a potential earth construction material. This paper gives an overview of the relevant Finnish legislation on the use of indu...

  17. Effects of polishing on surface roughness, gloss, and color of resin composites.

    Science.gov (United States)

    Hosoya, Yumiko; Shiraishi, Takanobu; Odatsu, Tetsuro; Nagafuji, Junichi; Kotaku, Mayumi; Miyazaki, Masashi; Powers, John M

    2011-09-01

    This study evaluated the effects of polishing on surface roughness, gloss, and color of regular, opaque, and enamel shades for each of three resin composites. Two-mm-thick resin disks made with Estelite Σ Quick, Clearfil Majesty, and Beautifil II were final polished with 180-, 1000-, and 3000-grit silicon carbide paper. Surface roughness, gloss, and color were measured one week after curing. Estelite Σ Quick had significantly lower roughness values and significantly higher gloss values as compared with Clearfil Majesty and Beautifil II. The effects of surface roughness and gloss on color (L*a*b*) differed among resin composites and by shade. Correlation coefficients between surface roughness and L*a*b* color factors were generally high for Clearfil Majesty, partially high (i.e., between roughness and L*) for Beautifil II, and low for Estelite Σ Quick. Correlation coefficients between gloss and L*a*b* color parameters were generally high for Beautifil II and low for Estelite Σ Quick and Clearfil Majesty. However, for all resin composites, the values of the color differences between 3000-grit and 180-grit polishing groups for all shades were imperceptible by the naked eye.

  18. Rumination's effect on suicide ideation through grit and gratitude: A path analysis study.

    Science.gov (United States)

    White, Evan J; Kraines, Morganne A; Tucker, Raymond P; Wingate, LaRicka R; Wells, Tony T; Grant, DeMond M

    2017-05-01

    The current study documents the relationship between suicide ideation, grit and gratitude, and rumination subtypes of brooding and reflection. The relationship between rumination and suicide ideation has been well documented and previous research has demonstrated that grit and gratitude are protective factors against suicide. We hypothesized that both subtypes of rumination would have an indirect effect on suicide ideation through levels of grit and gratitude. Results of a conditional indirect effects path analysis indicated that brooding was indirectly related to suicide ideation through gratitude. Brooding interacted with grit such that it only predicted suicide ideation at low levels of grit. Reflection interacted with gratitude to predict levels of grit. Results suggest that brooding may impact suicide risk and resilience through its effect on gratitude, indicating important cognitive-behavioral targets for suicide prevention strategies. These results extend the literature about the relationship between well known risk factors for suicide and protective factors. Copyright © 2017 Elsevier Ireland Ltd. All rights reserved.

  19. Characterization of gizzards and grits of wild cranes found dead at Izumi Plain in Japan.

    Science.gov (United States)

    Uegomori, Mima; Haraguchi, Yuko; Obi, Takeshi; Takase, Kozo

    2018-04-18

    We analyzed the gizzards, and grits retained in the gizzards of 41 cranes that migrated to the Izumi Plain during the winter of 2015/2016 and died there, either due to accident or disease. These included 31 Hooded Cranes (Grus monacha) and 10 White-naped Cranes (G. vipio). We determined body weight, gizzard weight, total grit weight and number per gizzard, and size, shape, and surface roundness of the grits. Average gizzard weights were 92.4 g for Hooded Cranes and 97.1 g for White-naped Cranes, and gizzard weight positively correlated with body weight in both species. Average total grit weights per gizzard were 19.7 g in Hooded Cranes and 25.7 g in White-naped Cranes, and were significantly higher in the latter. Average percentages of body weight to grit weight were 0.8% in Hooded Cranes and 0.5% in White-naped Cranes. Average grit number per gizzard was 693.5 in Hooded Cranes and 924.2 in White-naped Cranes, and were significantly higher in the latter. The average grit size was 2.8 mm in both species. No differences were found in the shape and surface roundness of grits between the two species. To the best of our knowledge, this is the first study on the grits retained in the gizzards of Hooded and White-naped Cranes.

  20. Grit and the brain: spontaneous activity of the dorsomedial prefrontal cortex mediates the relationship between the trait grit and academic performance

    Science.gov (United States)

    Zhou, Ming; Chen, Taolin; Yang, Xun; Chen, Guangxiang; Wang, Meiyun; Gong, Qiyong

    2017-01-01

    Abstract As a personality trait, grit involves the tendency to strive to achieve long-term goals with continual passion and perseverance and plays an extremely crucial role in personal achievement. However, the neural mechanisms of grit remain largely unknown. In this study, we aimed to explore the association between grit and the fractional amplitude of low-frequency fluctuations (fALFF) in 217 healthy adolescent students using resting-state functional magnetic resonance imaging (RS-fMRI). We found that an individual’s grit was negatively related to the regional fALFF in the right dorsomedial prefrontal cortex (DMPFC), which is involved in self-regulation, planning, goal setting and maintenance, and counterfactual thinking for reflecting on past failures. The results persisted even after the effects of general intelligence and the ‘big five’ personality traits were adjusted for. More importantly, the fALFF of the right DMPFC played a mediating role in the association between grit and academic performance. Overall, these findings reveal regional fALFF as a neural basis of grit and highlight the right DMPFC as a neural link between grit and academic performance. PMID:27672175

  1. Effect of calcium phosphate coating crystallinity and implant surface roughness on differentiation of rat bone marrow cells.

    NARCIS (Netherlands)

    Brugge, P.J. ter; Wolke, J.G.C.; Jansen, J.A.

    2002-01-01

    In this study, we examined the effect of calcium phosphate (Ca-P) coating crystallinity and of surface roughness on growth and differentiation of osteogenic cells. Grit-blasted titanium substrates were provided with Ca-P coatings of different crystallinities. Rat bone marrow (RBM) cells were

  2. Investigating Grit and Its Relations with College Students' Self-Regulated Learning and Academic Achievement

    Science.gov (United States)

    Wolters, Christopher A.; Hussain, Maryam

    2015-01-01

    We investigated grit and its relations with students' self-regulated learning (SRL) and academic achievement. An ethnically diverse sample of 213 college students completed an online self-report survey that included the Grit Short scale (Duckworth and Quinn "Journal of Personality Assessment, 91(2)," 166-174, 2009), seven indicators of…

  3. Grit: A Potential Protective Factor Against Substance Use and Other Risk Behaviors Among Latino Adolescents.

    Science.gov (United States)

    Guerrero, Lourdes R; Dudovitz, Rebecca; Chung, Paul J; Dosanjh, Kulwant K; Wong, Mitchell D

    2016-04-01

    Grit, defined as "working strenuously toward challenges, maintaining effort and interest over years despite failure, adversity, and plateaus in progress," is strongly associated with academic achievement and life success and may also be associated with health outcomes and behaviors. We examined predictors of grit, and the association between grit and health behaviors among at-risk Latino adolescents. We analyzed baseline survey data collected in 2013-2014 from a sample of 1270 9th graders in low-income neighborhoods of Los Angeles. We examined factors associated with grit and whether grit is associated with substance use and delinquent behaviors, controlling for adolescent and parent sociodemographic factors. In a sample of mostly Latino adolescents (89.5%), compared to those with low grit, those with high grit had significantly lower odds of alcohol use in the last 30 days (odds ratio 0.30, P authoritative parenting style, parental employment, and high self-efficacy scores. Grit may be an important candidate protective factor against substance use and other risk behaviors among Latino adolescents. Copyright © 2016 Academic Pediatric Association. Published by Elsevier Inc. All rights reserved.

  4. Investigating Grit Variables and Their Relations with Practice and Skill Groups in Developing Sport Experts

    Science.gov (United States)

    Tedesqui, Rafael A. B.; Young, Bradley W.

    2017-01-01

    Grit, the tendency to work hard toward long-term goals, maintaining effort and interest over years despite failure and adversity, has predicted several achievement outcomes. However, minimal work has examined grit within a sport expertise development framework, and specifically its association with deliberate practice (DP) in sport. Participants,…

  5. Positive Psychology Factors as Predictors of Latina/o College Students' Psychological Grit

    Science.gov (United States)

    Vela, Javier Cavazos; Smith, Wayne D.; Whittenberg, James F.; Guardiola, Rebekah; Savage, Miranda

    2018-01-01

    Latina/o college students (N = 130) provided perceptions of psychological grit, presence of meaning in life, search for meaning in life, hope, life satisfaction, and mindfulness. Hope and mindfulness were significant predictors of psychological grit. A discussion regarding the importance of these findings and implications for counselors are…

  6. Air-propelled abrasive grit can damage the perennial weed, quackgrass, Elytrigia repens (L.) Nevski

    Science.gov (United States)

    New techniques are needed to control quackgrass in organic crops. With greater than or equal to 2 applications of abrasive air-propelled (800 kPa) corncob grit to 15 cm tall quackgrass tillers, regrowth was minimal at 5 weeks after treatment. Abrasive grits may be effective tools to help manage pere...

  7. Stability amidst turmoil: Grit buffers the effects of negative life events on suicidal ideation.

    Science.gov (United States)

    Blalock, Dan V; Young, Kevin C; Kleiman, Evan M

    2015-08-30

    The goal of the current study is to examine the role of grit as a resilience factor that reduces the risk for suicidal ideation conferred by negative life events. Participants (N=209) completed measures of negative life events and grit at baseline and a measure of suicidal ideation at follow-up four weeks later. Poisson regression analyses found that higher levels of grit buffered the relationship between negative life events and suicidal ideation such that negative life events only predicted suicidal ideation if grit was low. These results suggest that high grit can abate the increased suicidal ideation associated with negative life events. Aside from absolute levels of suicidal ideation, being able to predict or buffer dramatic shifts in suicidal ideation can be a useful diagnostic tool during interventions. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

  8. Acid etching and plasma sterilization fail to improve osseointegration of grit blasted titanium implants

    DEFF Research Database (Denmark)

    Mortensen, Mikkel Saksø; Jakobsen, Stig Storgaard; Saksø, Henrik

    2012-01-01

    Interaction between implant surface and surrounding bone influences implant fixation. We attempted to improve the bone-implant interaction by 1) adding surface micro scale topography by acid etching, and 2) removing surface-adherent pro-inflammatory agents by plasma cleaning. Implant fixation...... was evaluated by implant osseointegration and biomechanical fixation.The study consisted of two paired animal sub-studies where 10 skeletally mature Labrador dogs were used. Grit blasted titanium alloy implants were inserted press fit in each proximal tibia. In the first study grit blasted implants were...... compared with acid etched grit blasted implants. In the second study grit blasted implants were compared with acid etched grit blasted implants that were further treated with plasma sterilization. Implant performance was evaluated by histomorphometrical investigation (tissue-to-implant contact, peri-implant...

  9. Diffuse reflectance FTIR of stains on grit blasted metals

    Energy Technology Data Exchange (ETDEWEB)

    Powell, G.L.; Hallman, R.L. Jr.; Cox, R.L. [Oak Ridge Centers for Manufacturing Technologies, TN (United States)

    1997-08-09

    Diffuse reflectance mid-infrared Fourier transform (DRIFT) spectroscopy has been applied to the detection of oil contamination on grit-blasted metals. The object of this application is to detect and discriminate between silicone and hydrocarbon oil contamination at levels approaching 10 mg/m{sup 2}. A portable FTIR spectrometer with dedicated diffuse reflectance optics was developed for this purpose. Using translation devices positioned by instructions from the spectrometer operating system, images of macroscopic substrates were produced with millimeter spatial resolution. The pixels that comprise an image are each a full mid-infrared spectrum with excellent signal-to-noise, each determined as individual files and uniquely saved to disc. Reduced spectra amplitudes, based on peak height, area, or other chemometric techniques, mapped as a function of the spatial coordinates of the pixel are used to display the image. This paper demonstrates the application of the technique to the analysis of stains on grit-blasted metals, including the calibration of the method, the inspection of substrates, and the migration of oil contamination.

  10. Turkana Grits - a Cretaceous braided alluvial system in northern Kenya

    Energy Technology Data Exchange (ETDEWEB)

    Handford, C.R.

    1987-05-01

    Rather spotty but excellent exposures of the Cretaceous-age Turkana Grits occur near the western shore of Lake Turkana, northern Kenya. These very coarse to pebbly arkosic sandstones and sandy conglomerates were derived from and rest unconformably upon Precambrian metamorphic basement; they are overlain by late Tertiary basaltic flows that comprise much of the volcanics in the East African Rift Zone. The formation ranges up to 2000 ft thick in the Laburr Range. Several outcrops contain sauropod, crocodile, and tortoise remains as well as abundant trunks of petrified wood (Dryoxylon). Five major facies make up the Turkana Grits and record a major episode of continental fluvial deposition in basins flanked by Precambrian basement. Facies 1 is crudely stratified, cobble and boulder conglomerate (clast-supported); Facies 2 is crudely stratified pebble-cobble conglomerate and pebbly sandstone; Facies 3 is trough cross-bedded, very coarse sandstones containing fossils wood and vertebrate remains; Facies 4 is crudely stratified to massive sandstones with ironstone nodules; and Facies 5 is red, purple, and gray mudstone and mud shale with carbonate nodules. Facies 1 through 3 record deposition in proximal to medial braided-stream channel, longitudinal bar and dune complexes. Facies 4 is a lowland, hydromorphic paleosol, and Facies 5 represents overbank and abandoned channel-fill sedimentation in an alluvial plain.

  11. Caracterização tecnológica de misturas solo-grits para pavimentos de estradas florestais: influência do tratamento térmico do grits na resistência mecânica das misturas Technological characterization of soil-grits mixtures for forest road pavements: influence of grits thermal treatment on the mechanical strength of mixtures

    Directory of Open Access Journals (Sweden)

    Carlos Cardoso Machado

    2007-01-01

    Full Text Available Analisou-se a influência do tratamento térmico do resíduo grits na resistência mecânica de misturas solo-grits para aplicações em pavimentos de estradas florestais. O programa de ensaios de laboratório englobou: (i dois solos residuais de gnaisse da Zona da Mata Norte de Minas Gerais; (ii um resíduo da indústria da celulose denominado grits, que é composto de cal não-hidratada e areia, entre outros produtos; (iii amostras de grits submetidas ao tratamento térmico em mufla sob temperaturas de 600, 700, 800 e 900 ºC antes da moldagem dos corpos-de-prova das misturas solo-grits; (iv corpos-de-prova das misturas preparadas com o grits tratado termicamente, com 24% de grits em relação ao peso seco dos solos, compactados nas energias dos ensaios Proctor intermediário e modificado e curados por 7 e 28 dias em câmara úmida, sob condições de aproximadamente 22 ºC de temperatura e 100% de umidade relativa do ar; e (v imersão completa dos corpos-de-prova das misturas solo-grits em água, pelo período de quatro horas, antes da determinação de suas resistências em ensaios de compressão não-confinada. Os resultados do programa de ensaios de laboratório indicaram que o tratamento térmico produziu amostras de grits mais reativas, podendo-se associar melhor desempenho mecânico às temperaturas de 800 e 900 ºC para o solo 1 e 800 ºC para o solo 2.The objective of this paper was to analyze the influence of grits thermal treatment on the mechanical strength of soil-grits mixtures. The laboratory testing program included: (i two residual gneiss soils from the Zona da Mata, Northern Minas Gerais; (ii waste from the cellulose industry, namely grits, composed by non-hydrated lime and sand, among others by-products; (iii grits samples submitted to thermal treatment in a muffle at the temperatures of 600, 700, 800 and 900 ºC before soils-grits specimens preparation; (iv soils-grits specimens containing 24% of treated grits in relation

  12. Size and mass of grit in gizzards of sandhill cranes, tundra swans, and mute swans

    Science.gov (United States)

    Franson, J. Christian; Hansen, Scott P.; Duerr, Adam E.; DeStefano, Stephen

    2001-01-01

    Because it has been suggested that waterbirds may ingest lost or discarded lead fishing weights as grit, we examined grit in the gizzards of Sandhill Cranes (Grus canadensis), Tundra Swans (Cygnus columbianus), and Mute Swans (Cygnus olor), three species where individuals have been poisoned by the ingestion of lead fishing weights. The greatest proportion (by mass) of grit in gizzards of Sandhill Cranes consisted of particles with a minimum dimension of 2.36-4.75 mm. Grit particles in swans were much smaller, with the most prevalent (by mass) being 0.6-1.18 mm. The greatest dimension of the largest grit particle found in cranes and swans was 17.4 mm and 14.0 mm, respectively. The U.S. Environmental Protection Agency has proposed a ban on lead fishing weights of ≤25.4 mm in any dimension. Based on the size of grit particles that we found in gizzards of Sandhill Cranes, Mute Swans, and Tundra Swans, we believe it is unlikely that individuals of those species would ingest, as grit, lead fishing weights larger than 25.4 mm in any dimension.

  13. PRODUCTION OF THE STEEL CAST THERMO-TREATED GRIT IN CONDITIONS OF MINSK AUTOMOBILE PLANT

    Directory of Open Access Journals (Sweden)

    P. S. Gurchenko

    2004-01-01

    Full Text Available The technical and economic characteristic of the created and developed technological processes of the industrial production of the steel casting grit heat-treatable by induction heat is given.

  14. Characterization and evaluation of residue 'grits' of the cellulose industry; Caracterizacao e avaliacao do resisduo 'grits' da industria de celulose

    Energy Technology Data Exchange (ETDEWEB)

    Destefani, A.Z.; Santos, M.M.; Holanda, J.N.F. [Universidade Estadual do Norte Fluminense Darcy Ribeiro (LAMAV/CCT/UENF), Campos dos Goytacazes, RJ (Brazil). Lab. de Materiais Avancados

    2010-07-01

    The cellulose industry generates huge amounts of solid waste residue called 'grits'. These wastes have been willing over time in landfills near the mills. However, this type of disposal is not environmentally friendly and can cause degradation and environmental pollution. In addition, environmental legislation increasingly severe and the high costs of landfill have led the search for new alternatives for final disposition of this abundant waste. In this context, this study is to characterize waste grits, generated by the cellulose industry in the region of Aracruz-ES. The residue samples were characterized in terms of chemical composition, X-ray diffraction, particle size distribution and thermal analysis (DTA and TGA). The characterization of the residual 'grits' demonstrated its potential as a feedstock for production of soil-cement bricks. (author)

  15. Capturing the Dual Pillars of Grit: The Synergistic Benefits of Perseverance and Passion for Performance

    OpenAIRE

    Wihler, Andreas; Jachimowicz, Jon; Galinsky, Adam

    2018-01-01

    Previous research has found mixed evidence regarding the relationship between grit-defined as perseverance and passion for long-term goals-and performance. We propose that this inconsistency has occurred because prior research has emphasized perseverance, both theoretically and empirically, while insufficiently incorporating passion. We suggest that a combination of the original grit measure-which emphasizes perseverance-with a measure that assesses whether individuals attain desired levels o...

  16. The grit effect: predicting retention in the military, the workplace, school and marriage

    OpenAIRE

    Eskreis-Winkler, Lauren; Shulman, Elizabeth P.; Beal, Scott A.; Duckworth, Angela L.

    2014-01-01

    Remaining committed to goals is necessary (albeit not sufficient) to attaining them, but very little is known about domain-general individual differences that contribute to sustained goal commitment. The current investigation examines the association between grit, defined as passion and perseverance for long-term goals, other individual difference variables, and retention in four different contexts: the military, workplace sales, high school, and marriage. Grit predicted retention over and ...

  17. Optimization of processing parameters of amaranth grits before grinding into flour

    Science.gov (United States)

    Zharkova, I. M.; Safonova, Yu A.; Slepokurova, Yu I.

    2018-05-01

    There are the results of experimental studies about the influence of infrared treatment (IR processing) parameters of the amaranth grits before their grinding into flour on the composition and properties of the received product. Using the method called as regressionfactor analysis, the optimal conditions of the thermal processing to the amaranth grits were obtained: the belt speed of the conveyor – 0.049 m/s; temperature of amaranth grits in the tempering silo – 65.4 °C the thickness of the layer of amaranth grits on the belt is 3 - 5 mm and the lamp power is 69.2 kW/m2. The conducted researches confirmed that thermal effect to the amaranth grains in the IR setting allows getting flour with a smaller size of starch grains, with the increased water-holding ability, and with a changed value of its glycemic index. Mathematical processing of experimental data allowed establishing the dependence of the structural and technological characteristics of the amaranth flour on the IR processing parameters of amaranth grits. The obtained results are quite consistent with the experimental ones that proves the effectiveness of optimization based on mathematical planning of the experiment to determine the influence of heat treatment optimal parameters of the amaranth grits on the functional and technological properties of the flour received from it.

  18. Analysis of turbulent heat and momentum transfer in a transitionally rough turbulent boundary layer

    Science.gov (United States)

    Doosttalab, Ali; Dharmarathne, Suranga; Tutkun, Murat; Adrian, Ronald; Castillo, Luciano

    2016-11-01

    A zero-pressure-gradient (ZPG) turbulent boundary layer over a transitionally rough surface is studied using direct numerical simulation (DNS). The rough surface is modeled as 24-grit sandpaper which corresponds to k+ 11 , where k+ is roughness height. Reynolds number based on momentum thickness is approximately 2400. The walls are isothermal and turbulent flow Prandtl number is 0.71. We simulate temperature as passive scalar. We compute the inner product of net turbulent force (d (u1ui) / dxi) and net turbulent heat flux (d (ui θ / dxi)) in order to investigate (i) the correlation between these vectorial quantities, (II) size of the projection of these fields on each other and (IIi) alignment of momentum and hear flux. The inner product in rough case results in larger projection and better alignment. In addition, our study on the vortices shows that surface roughness promotes production of vortical structures which affects the thermal transport near the wall.

  19. Effect of surface roughness on the aerodynamic characteristics of a symmetrical airfoil

    Energy Technology Data Exchange (ETDEWEB)

    Chakroun, W.; Al-Mesri, I.; Al-Fahad, S.

    2005-07-01

    The objective of this study is to investigate the effect of surface roughness by varying the roughness size and location on the aerodynamic characteristics of the airfoil. Test were conducted on the symmetrical airfoil models NACA 0012 in which the nature of the surface was varied from smooth to very rough and at a chord Reynolds number of 1.5*10{sup 5}. Different airfoil models with various roughness sizes and roughness locations were tested for different angles of attack. Lift, drag and pressure coefficients were measured and velocity profiles were determined for the smooth and grit 36 roughened models. It is shown that as the surface roughness increases, the minimum drag also increases due to the increase of the skin friction and the lift decreases. Surface roughness is seen to delay the stall angle and also increase the lift in the stall region. The airfoil model with the roughness located at the trailing edge shows minimum drag and maximum lift up to the stall angle compared to the other cases of different roughness locations. It is confirmed that, for the rough surface, a turbulent boundary layer exists where the laminar boundary layer is encountered for the smooth surface at the same Reynolds number. The measured skin friction for the rough surface is larger than that for the smooth surface. (author)

  20. Insoluble granite-grit allows broiler chicks to have better growth performance and gut health

    Directory of Open Access Journals (Sweden)

    Güray Erener

    Full Text Available ABSTRACT The objective of this study was to investigate the effects of insoluble granite-grit on growth performance and gut health status of broiler chicks. One hundred and sixty 14-day-old broiler chicks were allocated to experimental groups control and grit feeding. Each group included 80 birds divided by four replicates, each consisting of 20 birds, 10 males and 10 females. Feed intake, body weight gain, feed conversion ratio, carcass weight, dressing percentage, gut length, abdominal fat pad, and liver, heart, and gizzard weights were determined. Starter diet included 230 g crude protein (CP kg−1 and 3.15 Mcal metabolizable energy (ME kg−1 during the days 14 to 21; grower diet included 212 g CP kg−1 and 3.20 Mcal ME kg−1; and finisher diet included 190 g CP kg−1 and 3.20 Mcal ME kg-1. Control birds were fed broiler diets, while grit-fed birds were allowed to consume broiler diets, including 3% insoluble granite-grit. Grit feeding improved the final body weight (2268 vs. 2336 g with better feed efficiency (2.03 vs. 1.95 and less feed intake (3780 vs. 3764 g. Grit feeding increased gizzard weight (31.63 vs. 48.00 g without affecting carcass weight (1643 vs. 1708 g, dressing percentage (73.50 vs. 73.60%, liver weight (42.69 vs. 40.69 g, heart weight (12.00 vs. 11.63 g, abdominal fat pad (34.50 vs. 35.38 g, and gut length (229.3 vs. 220.7 cm of broilers. Grit feeding affects daily gain, feed intake, and feed conversion ratio positively by increasing gizzard development and health.

  1. Reduction of fumonisin B₁ in corn grits by twin-screw extrusion.

    Science.gov (United States)

    Jackson, Lauren S; Jablonski, Joseph; Bullerman, Lloyd B; Bianchini, Andreia; Hanna, Milford A; Voss, Kenneth A; Hollub, April D; Ryu, Dojin

    2011-08-01

    This study was designed to investigate the fate of fumonisins in flaking corn grits during twin-screw extrusion by measuring fumonisin B₁ (FB₁) and its analogs with a mass balance approach. Food grade corn grits and 2 batches of grits contaminated with FB₁ at 10 and 50 μg/g by Fusarium verticillioides M-2552 were processed with or without glucose supplementation (10%, w/w) with a twin-screw extruder. Extrusion reduced FB₁ in contaminated grits by 64% to 72% without glucose and 89% to 94% with added glucose. In addition, extrusion alone resulted in 26% to 73% reduction in the levels of fumonisin B₂ and fumonisin B₃, while levels of both mycotoxins were reduced by >89% in extruded corn grits containing 10% glucose. Mass balance analysis showed that 38% to 46% of the FB₁ species detected in corn extruded with glucose was N-(deoxy-D-fructos-1-yl)-FB₁, while 23% to 37% of FB₁ species detected in extruded corn grits with and without added glucose was bound to the matrix. It was also found that the hydrolyzed form of FB₁ was a minor species in extruded corn grits with or without added glucose, representing fumonisin analogues measured in this study. Research is needed to identify the reaction products resulting from extrusion processing of fumonisin-contaminated corn products. Twin-screw extrusion is widely used in food industry for its versatility. This technology may reduce the level of fumonisins in corn particularly with added glucose. Journal of Food Science © 2011 Institute of Food Technologists® No claim to original US government works.

  2. Effect of boiling, frying, and baking on recovery of aflatoxin from naturally contaminated corn grits or cornmeal.

    Science.gov (United States)

    Stoloff, L; Trucksess, M W

    1981-05-01

    Corn grits naturally contaminated with aflatoxins were used for making boiled grits, and portions of the boiled grits were used for making pan-fried grits; cornmeal naturally contaminated with aflatoxins was used for making corn muffins. Procedures and recipes were derived from cookbook and market package recommendations. From analyses of the products for aflatoxins before and after preparation of the table-ready products, it was determined that 72 +/- 9% (n = 15) of the aflatoxin found in the original grits could be recovered after the grits were boiled. The recovery of aflatoxin B1 after the grits were fried was either 66 +/- 10% (n = 6) or 47 +/- 8% (n = 9), depending on whether 3 cups of water or 4 cups of water per cup of grits, respectively, were used for preparing the boiled grits before frying. Similarly, it was determined that 87 +/- 4% (n = 9) of the aflatoxin B1 found in the original cornmeal could be recovered from the baked muffins. No detectable aflatoxin B2 a was present in the extracts from any of the table-ready products.

  3. Liquid abrasive grit blasting literature search and decontamination scoping tests report

    International Nuclear Information System (INIS)

    Ferguson, R.L.

    1993-10-01

    Past decontamination and solvent recovery activities at the Idaho Chemical Processing Plant (ICPP) have resulted in the accumulation of 1.5 million gallons of radioactively contaminated sodium-bearing liquid waste. Future decontamination activities at the ICPP could result in the production of 5 million gallons or more of sodium-bearing waste using the current decontamination techniques of chemical/water flushes and steam jet cleaning. With the curtailment of reprocessing at the ICPP, the focus of decontamination is shifting from maintenance for continued operation of the facilities to decommissioning. As decommissioning plans are developed, new decontamination methods must be used which result in higher decontamination factors and generate lower amounts of sodium-bearing secondary waste. The primary initiative of the WINCO Decontamination Development Program is the development of methods to eliminate/minimize the use of sodium-bearing decontamination chemicals. One method that was chosen for cold scoping studies during FY-93 was abrasive grit blasting. Abrasive grit blasting has been used in many industries and a vast amount of research and development has already been conducted. However, new grits, process improvements and ICPP applicability was investigated. This evaluation report is a summary of the research efforts and scoping tests using the liquid abrasive grit blasting decontamination technique. The purpose of these scoping tests was to determine the effectiveness of three different abrasive grits: plastic beads, glass beads and alumina oxide

  4. Experimental study on manufacturing of grits-spiral- distribution electroplated wire saw

    Directory of Open Access Journals (Sweden)

    Yufei GAO

    2016-12-01

    Full Text Available In order to obtain high performance electroplating diamond wire saw, experimental studies are conducted for development of grits-spiral-distribution electroplated diamond wire saw using sand-suspend electroplating method. The influences of pre-plating cathode current density, grits electro-embedding cathode current density and time on composite deposite coating appearance and grits distribution of wire saw are analyzed, and the sawing experiment is carried out by using the trial wire saw. The results show that good bonding strength between the coating and the steel wire can be obtained when the adopted cathode current density is 5.0 A/dm2 at pre-plating stage; good coating and girts distribution can be obtained when the adopted cathode current density is 5.0 A/dm2 and the electroplating time is 7~8 min at grits electro-embedding stage. By winding insulation wire on the surface of steel wire and reasonably selecting technological parameters before pre-plating can make the diamond wire saw with grits-spiral-distribution on surface, and the new type of wire saw has a better crumbs-clearing effect in wire sawing process.

  5. Diffusion of Drag-Reducing Polymers within a High-Reynolds-Number, Rough-Wall Turbulent Boundary Layer

    Science.gov (United States)

    Elbing, Brian; Perlin, Marc; Dowling, David; Solomon, Michael; Ceccio, Steven

    2008-11-01

    Two experiments were conducted to investigate polymer drag reduction (PDR) within high Reynolds number (to 200 million based on downstream distance), rough-wall turbulent boundary layers. The first experiment was conducted at the U.S. Navy's Large Cavitation Channel on a 12.9 m long flat-plate at speeds to 20 m/s with the surface hydraulically smooth and fully rough. Local skin-friction measurements on the smooth and rough surfaces had maximum PDR levels of 65 and 75 percent, respectively. However, PDR decreased with increasing downstream distance and flow speed more rapidly on the rough surface, and at the top speed no measureable level of PDR was observed. The roughness-induced increased diffusion was quantified with near-wall concentration measurements and the second experiment, which measured concentration profiles on a 0.94 m long flat-plate with three surface conditions: smooth, 240-grit, and 60-grit sandpaper. The increased diffusion does not fully explain the smooth-rough PDR differences observed in the first experiment. Rheological analysis of drawn samples from the first experiment indicates that polymer degradation (chain scission) could be responsible for the remaining loss of rough-wall PDR. These results have implications for the cost effectiveness of PDR for surface ships.

  6. Grit and burnout in UK doctors: a cross-sectional study across specialties and stages of training.

    Science.gov (United States)

    Halliday, Laura; Walker, Abigail; Vig, Stella; Hines, John; Brecknell, John

    2017-07-01

    Grit is characterised by the ability to persevere during difficulties and maintain a sustained effort over an extended period of time. Throughout their careers, doctors will experience many periods of stress and difficulty. This may result in burnout, defined by the presence of exhaustion and disengagement from work. This study aims to characterise the relationship between grit and burnout in doctors and to establish whether there are differences between specialties and levels of training. A multicentre cross-sectional survey by questionnaire was used. Participants were recruited from training days and an online medical forum. The survey consisted of the Short Grit Scale and the Oldenburg Burnout Inventory, which examine levels of grit and burnout, respectively. 548 responses were collected. We found a weak negative correlation between grit and burnout in UK doctors (r=-0.243, p<0.001). Hospital consultants had significantly higher grit scores than trainees. The highest level of burnout was found among general practitioners (GPs). When GPs were analysed separately, the correlation between grit and resilience was not seen. An understanding of an individual's level of grit may be used to identify doctors at a greater risk of burnout. As a high level of grit is associated with less burnout, interventions to improve grit through resilience training should be examined. Further research is needed to understand how grit levels change during a doctor's career and why GPs experience higher levels of burnout. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

  7. Effects of roughness on interfacial performances of silica glass and non-polar polyarylacetylene resin composites

    International Nuclear Information System (INIS)

    Jiang, Z.X.; Huang, Y.D.; Liu, L.; Long, J.

    2007-01-01

    The influence of roughness on interfacial performances of silica glass/polyarylacetylene resin composites was investigated. In order to obtain different roughness, silica glass surface was abraded by different grits of abrasives and its topography was observed by scanning electron microscopy and atomic force microscopy. At the same time, the failure mechanisms of composites were analyzed by fracture morphologies and the interfacial adhesion was evaluated by shear strength test. The results indicated that shear strength of silica glass/polyarylacetylene resin composites firstly increased and then decreased with the surface roughness of silica glass increased. The best surface roughness range of silica glass was 40-60 nm. The main mechanism for the improvement of the interfacial adhesion was physical interlocking at the interface

  8. Effect of surface roughness variation on the transmission characteristics of D-shaped fibers with ambient index change

    International Nuclear Information System (INIS)

    Kim, Hyun-Joo; Kwon, Oh-Jang; Han, Young-Geun

    2010-01-01

    The influence of surface roughness on the sensitivity of D-shaped fibers to changes in the ambient index was investigated. In order to obtain D-shaped fibers with different surface roughness, we polished one side of the fibers by using different abrasive grits. The topographies of the surfaces of the polished D-shaped fibers were then observed by using atomic force microscopy (AFM). The light scattered from the rough surfaces of the D-shaped fibers was measured by using optical microscopy. The effect of an ambient index change on the transmission characteristics of D-shaped fibers was measured for various values of the surface roughness. The experimental results indicate that variations in the surface roughness have a considerable influence on the sensitivity of the transmission characteristics of D-shaped fibers to changes in the ambient index.

  9. Measurement of surface roughness

    DEFF Research Database (Denmark)

    De Chiffre, Leonardo

    This document is used in connection with two 3 hours laboratory exercises that are part of the course GEOMETRICAL METROLOGY AND MACHINE TESTING. The laboratories include a demonstration of the function of roughness measuring instruments plus a series of exercises illustrating roughness measurement...

  10. Effects of irrigation frequency and grit color on the germination of lodgepole pine seeds

    Science.gov (United States)

    Jeremy R. Pinto; R. Kasten Dumroese; Douglas R. Cobos

    2009-01-01

    Nursery cultural practices during germination can be highly variable between existing production facilities. Although nursery guidebooks suggest keeping seeds moist, there are no known scientific answers indicating what sufficient moisture levels are. This study objective was to characterize differing irrigation regimes and grit color choices on different germination...

  11. Students' Achievement in Math and Science: How Grit and Attitudes Influence?

    Science.gov (United States)

    Al-Mutawah, Masooma Ali; Fateel, Moosa Jaafar

    2018-01-01

    Many recent studies in the field of mathematics and science education have been studying the effect of non-cognitive factors in students' achievement such as emotions, attitudes, values, beliefs, motivation, anxiety and grit. For example, attitude has been an important area in science education, and there have been many attempts to measure…

  12. Individual versus Peer Grit: Influence on Later Individual Literacy Achievement of Dual Language Learners

    Science.gov (United States)

    O'Neal, Colleen R.

    2018-01-01

    The objective of this short-term longitudinal study was to examine individual versus classroom peer effects of grit on later individual literacy achievement in elementary school. The dual language learner, largely Latina/o sample included students from the 3rd through the 5th grades. Participants completed a literacy achievement performance task…

  13. Spent coffee grounds as air-propelled abrasive grit for weed control

    Science.gov (United States)

    Spent coffee grounds (SCG) represent a significant food waste residue. Value-added uses for this material would be beneficial. Gritty agricultural residues, such as corncob grit, can be employed as abrasive air-propelled agents for organically-compatible postemergence shredding of weed seedlings sel...

  14. Chemical and Toxicological Fate of Fumonisin B1 during Extrusion Processing of Corn Grits

    Science.gov (United States)

    Two batches of flaking corn grits were prepared by growing Fusarium verticillioides to contain low and high levels of fumonisin B1 (FB1), Batch-1 at 9.7 ppm and Batch-2 at 50 ppm FB1 as determined by HPLC. These two batches were extruded (Batch-1E; Batch-2E) or extruded with 10% w/w glucose supplem...

  15. Positive Psychology and Familial Factors as Predictors of Latina/o Students' Psychological Grit

    Science.gov (United States)

    Vela, Javier C.; Lu, Ming-Tsan P.; Lenz, A. Stephen; Hinojosa, Karina

    2015-01-01

    Positive psychology is a useful framework to understand Latina/o students' experiences. In the current study, we examined how presence of meaning in life, search for meaning in life, hope, and family importance influenced 128 Latina/o college students' psychological grit. We used the Meaning in Life Questionnaire (MLQ), Subjective Happiness Scale,…

  16. The Relationships between Positive Thinking Skills, Academic Locus of Control and Grit in Adolescents

    Science.gov (United States)

    Çelik, Ismail; Sariçam, Hakan

    2018-01-01

    The main purpose of this study is to examine the possible relationships between academic locus of control, positive thinking skills and grit in high school students. The participants of the research are composed of 288 adolescents continuing their high school education from 4 different schools in Agri, Turkey, which were selected with convenient…

  17. Research on the Single Grit Scratching Process of Oxygen-Free Copper (OFC

    Directory of Open Access Journals (Sweden)

    Libin Zhang

    2018-04-01

    Full Text Available Single grit scratching is a basic form of material removal for many processes, such as grinding single point diamond turning and coating bonding performance tests. It has been widely used in the study of micro-scale and nano-scale material removal mechanisms. In this study, single grit linearly loading scratching tests were carried out on a scratching tester. A Rockwell indenter made of natural diamond was selected as the tool used, and the material of the workpiece was oxygen-free copper. Scratch topography was measured using a super-depth microscope to analyze the material deformation of the scratching process. A single grit scratching simulation has been developed by AdvantEdge™ to comprehensively study the material deformation of scratching processes. A material constitutive model and friction model were acquired using a quasi-static uniaxial compression experiment and a reciprocating friction test, respectively. These two models were used as the input models in the finite simulations. The simulated scratching forces aligned well with the experimental scratching forces, which verified the precision of the simulation model. Since only the scratching force could be obtained in the scratching experiment, the plastic strain, material flow, and residual stress of the scratching were further analyzed using simulations. The results showed that the plastic strain of the workpiece increased with the increase in scratching depth, and further analysis showed that the workpiece surface was distributed with residual compressive stress and the sub-surface was distributed with residual tensile stress in single grit scratching.

  18. Rough multiple objective decision making

    CERN Document Server

    Xu, Jiuping

    2011-01-01

    Rough Set TheoryBasic concepts and properties of rough sets Rough Membership Rough Intervals Rough FunctionApplications of Rough SetsMultiple Objective Rough Decision Making Reverse Logistics Problem with Rough Interval Parameters MODM based Rough Approximation for Feasible RegionEVRMCCRMDCRM Reverse Logistics Network Design Problem of Suji Renewable Resource MarketBilevel Multiple Objective Rough Decision Making Hierarchical Supply Chain Planning Problem with Rough Interval Parameters Bilevel Decision Making ModelBL-EVRM BL-CCRMBL-DCRMApplication to Supply Chain Planning of Mianyang Co., LtdStochastic Multiple Objective Rough Decision Multi-Objective Resource-Constrained Project Scheduling UnderRough Random EnvironmentRandom Variable Stochastic EVRM Stochastic CCRM Stochastic DCRM Multi-Objective rc-PSP/mM/Ro-Ra for Longtan Hydropower StationFuzzy Multiple Objective Rough Decision Making Allocation Problem under Fuzzy Environment Fuzzy Variable Fu-EVRM Fu-CCRM Fu-DCRM Earth-Rock Work Allocation Problem.

  19. Gender, Math Confidence, and Grit: Relationships with Quantitative Skills and Performance in an Undergraduate Biology Course.

    Science.gov (United States)

    Flanagan, K M; Einarson, J

    2017-01-01

    In a world filled with big data, mathematical models, and statistics, the development of strong quantitative skills is becoming increasingly critical for modern biologists. Teachers in this field must understand how students acquire quantitative skills and explore barriers experienced by students when developing these skills. In this study, we examine the interrelationships among gender, grit, and math confidence for student performance on a pre-post quantitative skills assessment and overall performance in an undergraduate biology course. Here, we show that females significantly underperformed relative to males on a quantitative skills assessment at the start of term. However, females showed significantly higher gains over the semester, such that the gender gap in performance was nearly eliminated by the end of the semester. Math confidence plays an important role in the performance on both the pre and post quantitative skills assessments and overall performance in the course. The effect of grit on student performance, however, is mediated by a student's math confidence; as math confidence increases, the positive effect of grit decreases. Consequently, the positive impact of a student's grittiness is observed most strongly for those students with low math confidence. We also found grit to be positively associated with the midterm score and the final grade in the course. Given the relationships established in this study among gender, grit, and math confidence, we provide "instructor actions" from the literature that can be applied in the classroom to promote the development of quantitative skills in light of our findings. © 2017 K. M. Flanagan and J. Einarson. CBE—Life Sciences Education © 2017 The American Society for Cell Biology. This article is distributed by The American Society for Cell Biology under license from the author(s). It is available to the public under an Attribution–Noncommercial–Share Alike 3.0 Unported Creative Commons License (http

  20. Effects of polishing on surface roughness, gloss and color of surface reaction type pre-reacted glass-ionomer filled resin composite.

    Science.gov (United States)

    Hosoya, Yumiko; Shiraishi, Takanobu; Odatsu, Tetsuro; Miyazaki, Masashi; García-Godoy, Franklin

    2011-06-01

    To evaluate the effects of polishing on surface roughness, gloss and color of different shades of surface reaction type pre-reacted glass-ionomer (S-PRG) filled nano-hybrid resin composite. Resin disks of 15 mm diameter and 2 mm thickness and final polish with 1000-grit SiC paper, super fine cut diamond (FG) point, silicon (MFR) point and Super-Snap mini-disk red (SNAP) were made with Beautifil II shades: A2, A20, Inc). One week after curing, the surface roughness, gloss and color were measured. Data was analyzed with ANOVA and Fisher's PLSD with alpha= 0.05 For all shades, the order of roughness (Ra) ranked according to groups of 1000-grit SiC > FG > MFR > SNAP with significant differences among all groups. For all shades, the order of gloss ranked according to groups of SNAP > MFR > FG > 1000-grit SiC with significant differences among the groups except for between MFR and FG without significant difference. The influence of the surface roughness on color differed among the polishing groups and shades. However, the values of the color differences (deltaE*ab) between the polishing groups of all shades were imperceptible to the naked eye.

  1. Grit-mediated frictional ignition of a polymer-bonded explosive during oblique impacts: Probability calculations for safety engineering

    International Nuclear Information System (INIS)

    Heatwole, Eric; Parker, Gary; Holmes, Matt; Dickson, Peter

    2015-01-01

    Frictional heating of high-melting-point grit particles during oblique impacts of consolidated explosives is considered to be the major source of ignition in accidents involving dropped explosives. It has been shown in other work that the lower temperature melting point of two frictionally interacting surfaces will cap the maximum temperature reached, which provides a simple way to mitigate the danger in facilities by implementing surfaces with melting points below the ignition temperature of the explosive. However, a recent series of skid testing experiments has shown that ignition can occur on low-melting-point surfaces with a high concentration of grit particles, most likely due to a grit–grit collision mechanism. For risk-based safety engineering purposes, the authors present a method to estimate the probability of grit contact and/or grit–grit collision during an oblique impact. These expressions are applied to potentially high-consequence oblique impact scenarios in order to give the probability of striking one or more grit particles (for high-melting-point surfaces), or the probability of one or more grit–grit collisions occurring (for low-melting-point surfaces). The probability is dependent on a variety of factors, many of which can be controlled for mitigation to achieve acceptable risk levels for safe explosives handling operations. - Highlights: • Unexpectedly, grit-mediated ignition of a PBX occurred on low-melting point surfaces. • On high-melting surfaces frictional heating is due to a grit–surface interaction. • For low-melting point surfaces the heating mechanism is grit–grit collisions. • A method for estimating the probability of ignition is presented for both surfaces

  2. Organic geochemistry of petroleum seepages within the Jurassic Bencliff Grit, Osmington Mills, Dorset, UK

    Energy Technology Data Exchange (ETDEWEB)

    Watson, D.F.; Farrimond, P. [University of Newcastle upon Tyne (United Kingdom). Fossil Fuels and Environmental Geochemistry; Hindle, A.D. [Egdon Resources (UK) Ltd., Odiham (United Kingdom)

    2000-11-01

    Occurrences of oil within the Bencliff Grit at Osmington Mills were studied through an integration of organic geochemistry and a consideration of the geological setting. Oil-stained sandstones dominate the cliff outcrop with localized regions of particularly concentrated oil impregnation. A second 'live' seep of oil occurs where the Bencliff Grit beds pass below high tide level at Bran Point. Organic geochemical analyses showed both oils to be at least moderately biodegraded, with the oils in the cliff outcrop showing enrichment in polar constituents compared with the active seep. Multivariate statistical analysis of the molecular composition identified an enrichment in diasterane biomarkers in the oils of the live seep; this difference is ascribed to source and/or maturity differences. The oil within the outcrop is considered to represent the residual staining of an unroofed oil field, whilst the live seepage at Bran Point represents a migration pathway towards the eroded anticline. (Author)

  3. Relationships among grit, academic performance, perceived academic failure, and stress in associate degree students.

    Science.gov (United States)

    Lee, Wincy Wing Sze

    2017-10-01

    The present study examined the relationships among grit, academic performance, perceived academic failure, and stress levels of Hong Kong associate degree students using path analysis. Three hundred and forty-five students from a community college in Hong Kong voluntarily participated in the study. They completed a questionnaire that measured their grit (operationalized as interest and perseverance) and stress levels. The students also provided their actual academic performance and evaluated their perception of their academic performance as a success or a failure. The results of the path analysis showed that interest and perseverance were negatively associated with stress, and only perceived academic failure was positively associated with stress. These findings suggest that psychological appraisal and resources are more important antecedents of stress than objective negative events. Therefore, fostering students' psychological resilience may alleviate the stress experienced by associate degree students or college students in general. Copyright © 2017 The Foundation for Professionals in Services for Adolescents. Published by Elsevier Ltd. All rights reserved.

  4. The Role of Grit in College Student Health Care Management Skills and Health-Related Quality of Life.

    Science.gov (United States)

    Sharkey, Christina M; Bakula, Dana M; Gamwell, Kaitlyn L; Mullins, Alexandria J; Chaney, John M; Mullins, Larry L

    2017-10-01

    To examine the relationship of grit, an intrapersonal characteristic defined by perseverance and passion for long-term goals, to health care management skills and adolescent and young adult (AYA) health-related quality of life (HRQoL). Higher levels of grit were expected to relate to greater health care management skills and HRQoL, and skills were predicted to mediate the relationship between grit and HRQoL. Four hundred seventy undergraduates (Mdnage=19, interquartile range = 2) completed online questionnaires, including the short Grit Scale, Transition Readiness Assessment Questionnaire, and 36-Item Short Form Survey (SF-36) (HRQoL). Higher grit related to greater health care management skills (R2=0.15 p.05). This preliminary investigation illustrates the role of grit in AYA health, suggesting that it may be a target for interventions aimed at improving skills and HRQoL outcomes. © The Author 2017. Published by Oxford University Press on behalf of the Society of Pediatric Psychology. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com

  5. The effects of different sizes of insoluble grit on growth performance and carcass traits in broiler chickens

    Directory of Open Access Journals (Sweden)

    Abbas Ali Rajabiyan Moghaddam

    2016-04-01

    Full Text Available The present study was conducted to investigate the effects of different sizes of insoluble grit on growth performance and carcass traits in broiler chickens. A total of 200 broilers (Ross 308, 10 days old, were randomly allotted to five experimental equal groups with four replicates of 10 chickens (five male and five female and fed with basal diet + ground wheat (without grit; basal diet + whole wheat (without grit and basal diet contain 1.5% grit of diet with sizes of 2, 3 and 4 mm. Growth performance (evaluated through weight gain, feed intake and feed conversion ratio was determined on day 24 and 42. Also, carcass traits (relative weights of carcass, breast, thigh, liver, heart, gizzard and intestine and intestine length were assessed on day 42. Weight gains and feed conversion ratio were significantly improved in broilers added with grit 2 mm compared to the control group (p<0.05, whereas; carcass traits were not significantly altered. These data suggest that grit with size of 2 mm improve growth performance in broiler chickens.

  6. The grit effect: predicting retention in the military, the workplace, school and marriage.

    Science.gov (United States)

    Eskreis-Winkler, Lauren; Shulman, Elizabeth P; Beal, Scott A; Duckworth, Angela L

    2014-01-01

    Remaining committed to goals is necessary (albeit not sufficient) to attaining them, but very little is known about domain-general individual differences that contribute to sustained goal commitment. The current investigation examines the association between grit, defined as passion and perseverance for long-term goals, other individual difference variables, and retention in four different contexts: the military, workplace sales, high school, and marriage. Grit predicted retention over and beyond established context-specific predictors of retention (e.g., intelligence, physical aptitude, Big Five personality traits, job tenure) and demographic variables in each setting. Grittier soldiers were more likely to complete an Army Special Operations Forces (ARSOF) selection course, grittier sales employees were more likely to keep their jobs, grittier students were more likely to graduate from high school, and grittier men were more likely to stay married. The relative predictive validity of grit compared to other traditional predictors of retention is examined in each of the four studies. These findings suggest that in addition to domain-specific influences, there may be domain-general individual differences which influence commitment to diverse life goals over time.

  7. The grit effect: predicting retention in the military, the workplace, school and marriage

    Directory of Open Access Journals (Sweden)

    Lauren eEskreis-Winkler

    2014-02-01

    Full Text Available Remaining committed to goals is necessary (albeit not sufficient to attaining them, but very little is known about domain-general individual differences that contribute to sustained goal commitment. The current investigation examines the association between grit, defined as passion and perseverance for long-term goals, other individual difference variables, and retention in four different contexts: the military, workplace sales, high school, and marriage. Grit predicted retention over and beyond established context-specific predictors of retention (e.g. intelligence, physical aptitude, Big Five personality traits, job tenure and demographic variables in each setting. Grittier soldiers were more likely to complete an Army Special Operations Forces (ARSOF selection course, grittier sales employees were more likely to keep their jobs, grittier students were more likely to graduate from high school, and grittier men were more likely to stay married. The relative predictive validity of grit compared to other traditional predictors of retention is examined in each of the four studies. These findings suggest that in addition to domain-specific influences, there may be domain-general individual differences which influence commitment to diverse life goals over time.

  8. Generalized rough sets

    International Nuclear Information System (INIS)

    Rady, E.A.; Kozae, A.M.; Abd El-Monsef, M.M.E.

    2004-01-01

    The process of analyzing data under uncertainty is a main goal for many real life problems. Statistical analysis for such data is an interested area for research. The aim of this paper is to introduce a new method concerning the generalization and modification of the rough set theory introduced early by Pawlak [Int. J. Comput. Inform. Sci. 11 (1982) 314

  9. The Role of Self-control and Grit in Domains of School Success in Students of Primary and Secondary School.

    Science.gov (United States)

    Oriol, Xavier; Miranda, Rafael; Oyanedel, Juan C; Torres, Javier

    2017-01-01

    Objective: Self-control and grit have become two of the most important variables that explain success in different aspects of people's daily life (Duckworth and Gross, 2014). Self-control promotes delayed gratification and directly influences thoughts, emotions, and impulses. On the other hand, grit enhances the achievement of goals through perseverance even before extreme external circumstances. Since both constructs are related, examining them together is compelling, as long as the different nuances that characterize each are taken into account. Two structural equation models (SEM) were conducted to observe the effect of self-control and grit on a more specific indicator of academic success (academic self-efficacy) and a more general indicator of school experience (satisfaction with school). Methods: The first model comprises 5,681 primary students ( M = 9.05; SD = 0.79), and the second 10,017 secondary students ( M = 14.20; SD = 1.04) from Lima, Peru. In both models, the influence of grit and self-control on school satisfaction was observed when taking self-efficacy as a mediator variable. Results: The results show that grit and self-control have strong associations in both primary and secondary students. When estimating the covariance of both constructs, grit is related with academic-self efficacy at both educational stages, but only to satisfaction with school in secondary students. On the contrary, self-control shows a significant relationship with school satisfaction only in primary education. In turn, self-efficacy shows a mediating effect between grit and school satisfaction. After calculating the invariance of the models, differences are observed by gender in the relationships between variables. Conclusion: The results indicate that both constructs are strongly interrelated. Regarding the associations with the indicators of academic success, a need for timely interventions specific to each educational stage is observed.

  10. Roughing up Beta

    DEFF Research Database (Denmark)

    Bollerslev, Tim; Li, Sophia Zhengzi; Todorov, Viktor

    -section. An investment strategy that goes long stocks with high jump betas and short stocks with low jump betas produces significant average excess returns. These higher risk premiums for the discontinuous and overnight market betas remain significant after controlling for a long list of other firm characteristics......Motivated by the implications from a stylized equilibrium pricing framework, we investigate empirically how individual equity prices respond to continuous, or \\smooth," and jumpy, or \\rough," market price moves, and how these different market price risks, or betas, are priced in the cross......-section of expected returns. Based on a novel highfrequency dataset of almost one-thousand individual stocks over two decades, we find that the two rough betas associated with intraday discontinuous and overnight returns entail significant risk premiums, while the intraday continuous beta is not priced in the cross...

  11. Superficial roughness on composite surface, composite enamel and composite dentin junctions after different finishing and polishing procedures. Part I: roughness after treatments with tungsten carbide vs diamond burs.

    Science.gov (United States)

    Ferraris, Federico; Conti, Alessandro

    2014-01-01

    The aim of this study is to investigate different instruments for finishing composite restorations, as well as examining different surfaces and interfaces of the same restoration. The null hypothesis is represented by the fact that there are no significant differences on roughness of composite restorations finishing between tungsten carbide and diamond burs, furthermore the null hypothesis is that there are no significant differences on roughness between finishing on composite surfaces (C), compositeenamel (CE) and composite-dentin (CD) interfaces. The study was performed on 28 teeth, and class V cavities were prepared on the extracted teeth. Restorations were done in Filtek XTE nanofilled composite (3M Espe) in a standardized method, to then be finished. A comparison was made in the phase 1 between tungsten carbide burs (16 blades), diamond burs (46 μm), with a similar shape by the same manufacturer (Komet). Each surface received 5 bur applications. Consequently, an analysis with a profilometer was performed. Phase 2 involved further confrontation of ulterior finishing with ultrafine tungsten carbide burs (30 blades) and with extra and ultrafine diamond burs (25 and 8 μm) (the same shape as previously mentioned). A second analysis was then performed with a profilometer. All measurements were taken on C surfaces, CE and CD interfaces. Statistical analyses were carried out with c2 test (a = 0.05). The finishing procedures with fine grit or toothing burs gave a better smoothness with tungsten carbide burs compared to diamond burs. While with the ultrafine grit no significant differences were noted between tungsten carbide and diamond burs on the CE and CD interfaces, the diamond bur left less superficial roughness on the C surfaces. With regards to the superficial roughness of the different areas of restoration, it can be concluded that: minor roughness was detected on C surfaces, while the CD interface had the most superficial roughness, regardless of whether the

  12. Comportamento geotécnico de misturas granulométricas de solo-grits Mechanical behavior of the differents soil-grits granulometrics mixtures

    Directory of Open Access Journals (Sweden)

    Carlos Cardoso Machado

    2009-06-01

    Full Text Available Neste artigo, analisa-se a influência das diversas frações granulométricas do resíduo grits nos parâmetros ótimos de compactação, resistência mecânica e expansão, quando em misturas com dois solos típicos da Zona da Mata Norte de Minas Gerais, Brasil, com fins de aplicação em estradas florestais. Os teores de resíduo empregados nas misturas foram de 4, 8, 12, 16, 20, 24 e 28%, em relação à massa seca de solos, trabalhando-se com as energias de compactação dos ensaios Proctor intermediário e modificado. As frações de resíduo estudadas foram as equivalentes à argila e silte (d This paper addresses the influence of size distribution of the industrial waste named grits on the optimum compaction parameters, mechanical strength and swelling of two typical soils from the North Forest Zone of Minas Gerais State, Brazil, for forest road applications. Specimens compacted at the intermediate and modified Proctor compaction effort and waste contents of 4, 8, 12, 16, 20, 24 and 28 % regarding soil dry unit weights were used throughout the study. Waste sizes analyzed in the laboratory testing program were those equivalent to clay (d 2 mm and gravel (2 mm < d < 76 mm sizes in accordance to the DNIT technical standard (DNIT, 1996. Soils and mixtures bearing capacity and swelling were evaluated by the CBR test. Data from the laboratory testing program support that the waste's clay and gravel size portions were responsible, respectively, for higher and lower increases in soils bearing capacity.

  13. Bioceramic inlays do not improve mechanical incorporation of grit-blasted titanium stems in the proximal sheep femur.

    Science.gov (United States)

    Keränen, Pauli; Koort, Jyri; Itälä, Ari; Ylänen, Heimo; Dalstra, Michel; Hupa, Mikko; Kommonen, Bertel; Aro, Hannu T

    2010-03-15

    The aim of the present study was to determine, if bioactive glass (BG) surface inlays improve osseointegration of titanium implants in the proximal femur of adult sheep. In simulation of uncemented primary stems (nine animals), only the proximal part of the implants was grit-blasted and three surface slots of the grit-blasted region were filled with sintered BG microspheres. Primary stems were implanted using press-fit technique. In revision stem simulation (eight animals), grit-blasting was extended over the whole implant and seven perforating holes of the stem were filled by sintered BG granules. Revision stems were implanted with a mixture of autogenous bone graft and BG granules. Comparison with solid partially or fully grit-blasted control stems implanted in the contralateral femurs was performed in the primary and revision stem experiments at 12 and 25 weeks, respectively. Implant incorporation was evaluated by torsional failure testing and histomorphometry. Only one-third of the primary stems anchored mechanically to bone. The revision stems incorporated better and the BG inlays of the revision stems showed ingrowth of new bone. However, there were no significant differences in the torsional failure loads between the stems with BG inlays and the control stems. In conclusion, surface BG inlays gave no measurable advantage in mechanical incorporation of grit-blasted titanium implants. Overall, the proximal sheep femur, characterized by minimal amount of cancellous bone and the presence of adipocytic bone marrow, seemed to present compromised bone healing conditions. (c) 2009 Wiley Periodicals, Inc.

  14. Distribution of MCA-coated grits in maize fields after high wheel tractor application for disrupting orientation of Diabrotica virgifera virgifera LeConte.

    Science.gov (United States)

    Wennemann, Ludger; Hummel, Hans E

    2002-01-01

    High wheel tractor applications of 4-methoxycinnamaldehyde (MCA)-coated corn granules ('grits') were conducted in Ruski Krstur (Serbia) in summer 2001 in a 5 ha corn field. Grits are a by-product after corn is harvested and separated from the cob and used as a carrier medium to disseminate MCA into the corn field. MCA is a kairomone mimic derived form Cucurbita maxima (Duchesne) used to disrupt orientation of Diabrotica virgifera virgifera LeConte towards different MCA and pheromone baited traps. The ultimate goal is to investigate the use of MCA as a mating disruptant. MCA was dissolved in an organic solvent and mixed in a cement machine with the grits. Grits were applied at rates of 17.39, 17.1 and 12.45 kg/ha on July 4th, July 19th and August 3rd. Before the impact of MCA as a disruptant can be addressed, the distribution patterns of MCA coated grits have to be thoroughly investigated. They were evaluated by counting girts deposited in 16 or 20 plastic dishes of 30-cm diameter positioned along 2 rows through the field directly after the grit application by tractor. Additionally, grits deposited on corn plant surface such as leaves, leaf axils and corn cobs were counted. Total number of grits collected in plastic dishes revealed even application rates at the first and second application but not on the third application date. Number of grits collected on plant surfaces were significantly different from each other regarding each application date. Altogether, grit distribution in the dishes as well as on the plant surface was variable. However, distribution patterns achieved so far hold promise to disseminate MCA coated grits into corn fields for orientation disruption or mating disruption of D. virgifera virgifera.

  15. Effect of grit blasting on the thermal cycling behavior of diffusion aluminide/YSZ TBCs

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Zhenhua, E-mail: zhxuciac@163.com; Huang, Guanghong; He, Limin; Mu, Rende; Wang, Kai; Dai, Jianwei

    2014-02-15

    Highlights: • TBCs including of CVD NiAl bond coat and EB-PVD YSZ ceramic coating with and without grit blasting process. • Grain boundary ridges are the sites for spallation damage initiation in aluminide/YSZ TBCs. • Ridges are removed, and no cavity formation and this damage initiation mode are suppressed. • Damage initiation and progression occurs at the bond coat to TGO interface leading to a buckling failure behavior. -- Abstract: Thermal barrier coating system (TBCs) including of chemical vapor deposited NiAl bond coat and electron beam physical vapor deposited Y{sub 2}O{sub 3}–stabilized-ZrO{sub 2} (YSZ) ceramic coating with and without grit blasting process were investigated. The phase structures, surface and cross-sectional morphologies, cyclic oxidation behaviors of these coatings were studied in detail. Grain boundary ridges form on the surface of aluminide bond coat prior to the deposition of the ceramic coating by EB-PVD, which are shown to be the sites for spallation damage initiation in aluminide/YSZ TBCs. When these ridges are removed, there is no cavity formation and this damage initiation mode is suppressed. Damage initiation and progression occurs at the bond coat to TGO interface leading to a buckling failure behavior. A buckle failure once started may be arrested when it runs into a region of high bond coat to TGO interface toughness. Thus, complete failure requires further loss in toughness of the bond coat to TGO interface with additional cycling. From the result of thermal cycling, an averaged four folds lifetime improvement can be achieved with samples after grit blasting of bond coat surface as compared with those samples existence in ridges on the bond coats’ surface.

  16. Surface impurity removal from DIII-D graphite tiles by boron carbide grit blasting

    International Nuclear Information System (INIS)

    Lee, R.L.; Hollerbach, M.A.; Holtrop, K.L.; Kellman, A.G.; Taylor, P.L.; West, W.P.

    1993-11-01

    During the latter half of 1992, the DIII-D tokamak at General Atomics (GA) underwent several modifications of its interior. One of the major tasks involved the removal of accumulated metallic impurities from the surface of the graphite tiles used to line the plasma facing surfaces inside of the tokamak. Approximately 1500 graphite tiles and 100 boron nitride tiles from the tokamak were cleaned to remove the metallic impurities. The cleaning process consisted of several steps: the removed graphite tiles were permanently marked, surface blasted using boron carbide (B 4 C) grit media (approximately 37 μm. diam.), ultrasonically cleaned in ethanol to remove loose dust, and outgassed at 1000 degrees C. Tests were done using, graphite samples and different grit blaster settings to determine the optimum propellant and abrasive media pressures to remove a graphite layer approximately 40-50 μm deep and yet produce a reasonably smooth finish. EDX measurements revealed that the blasting technique reduced the surface Ni, Cr, and Fe impurity levels to those of virgin graphite. In addition to the surface impurity removal, tritium monitoring was performed throughout the cleaning process. A bubbler system was set up to monitor the tritium level in the exhaust gas from the grit blaster unit. Surface wipes were also performed on over 10% of the tiles. Typical surface tritium concentrations of the tiles were reduced from about 500 dpm/100 cm 2 to less than 80 dpm/100 cm 2 following the cleaning. This tile conditioning, and the installation of additional graphite tiles to cover a high fraction of the metallic plasma facing surfaces, has substantially reduced metallic impurities in the plasma discharges which has allowed rapid recovery from a seven-month machine opening and regimes of enhanced plasma energy confinement to be more readily obtained. Safety issues concerning blaster operator exposure to carcinogenic metals and radioactive tritium will also be addressed

  17. Suplementasi Tepung Putih Telur untuk Memperbaiki Nilai Nutrisi Snack Ekstrusi Berbahan Grits Jagung

    OpenAIRE

    Budiman, C; Wulandari, Z; Suryati, T

    2009-01-01

    Snack is popular for children and adult. It could be made by extrusion process. Snack is low in protein content because it is made up of cereal such as rice and corn. On the basis of nutritional and functional properties, egg was used in food industries. The objectives of the research were to analyze the nutrient content and in vitro digestibility of extruded snack from corn grits which was supplemented by egg white powder as a protein source. Randomized complete block design was used in this...

  18. Transition Experiments on Blunt Bodies with Distributed Roughness in Hypersonic Free Flight in Carbon Dioxide

    Science.gov (United States)

    Wilder, Michael C.; Reda, Daniel C.; Prabhu, Dinesh K.

    2015-01-01

    Blunt-body geometries were flown through carbon dioxide in the NASA Ames Hypervelocity Free Flight Aerodynamic Facility to investigate the influence of distributed surface roughness on transition to turbulence in CO2-dominated atmospheres, such as those of Mars and Venus. Tests were also performed in air for direct comparison with archival results. Models of hemispherical and spherically-blunted large-angle conical geometries were flown at speeds between 2.8 km/s and 5.1 km/s and freestream pressures between 50 Torr and 228 Torr. Transition fronts were determined from global surface heat flux distributions measured using thermal imaging techniques. Distributed surface roughness was produced by grit-blasting the model surfaces. Real-gas Navier-Stokes solutions were used to calculate non-dimensional correlating parameters at the measured transition onset locations. Transition-onset locations correlated well with a constant roughness Reynolds number based on the mean roughness element height. The critical roughness Reynolds number for transition onset determined for flight in CO2 was 223 +/- 25%. This mean value is lower than the critical value of 250 +/- 20% previously-established from tests conducted in air, but within the bounds of the expected measurement uncertainty.

  19. Modelling dynamic roughness during floods

    NARCIS (Netherlands)

    Paarlberg, Andries; Dohmen-Janssen, Catarine M.; Hulscher, Suzanne J.M.H.; Termes, A.P.P.

    2007-01-01

    In this paper, we present a dynamic roughness model to predict water levels during floods. Hysteresis effects of dune development are explicitly included. It is shown that differences between the new dynamic roughness model, and models where the roughness coefficient is calibrated, are most

  20. Notions of Rough Neutrosophic Digraphs

    Directory of Open Access Journals (Sweden)

    Nabeela Ishfaq

    2018-01-01

    Full Text Available [-3]Graph theory has numerous applications in various disciplines, including computer networks, neural networks, expert systems, cluster analysis, and image capturing. Rough neutrosophic set (NS theory is a hybrid tool for handling uncertain information that exists in real life. In this research paper, we apply the concept of rough NS theory to graphs and present a new kind of graph structure, rough neutrosophic digraphs. We present certain operations, including lexicographic products, strong products, rejection and tensor products on rough neutrosophic digraphs. We investigate some of their properties. We also present an application of a rough neutrosophic digraph in decision-making.

  1. Interfacial microstructure and performance of brazed diamond grits with Ni-Cr-P alloy

    Energy Technology Data Exchange (ETDEWEB)

    Wang, C.Y. [Faculty of Mechanical and Electronic Engineering, Guangdong University of Technology, Guangzhou 510006 (China)], E-mail: cywang@gdut.edu.cn; Zhou, Y.M.; Zhang, F.L.; Xu, Z.C. [Faculty of Mechanical and Electronic Engineering, Guangdong University of Technology, Guangzhou 510006 (China)

    2009-05-12

    The reaction mechanism of the interface among diamond, commercial Ni-Cr-P alloy and steel substrate has been studied by optical microscopy, scanning electron microscope, X-ray diffraction and Raman spectroscopy. The reaction layers formed among diamond, brazing alloy and steel substrate produced good wettability of diamond grits for achieving better quality tools. The reaction layer between diamond and brazing alloy comprised a reaction layer of brazing alloy and a reaction layer of diamond. Cr{sub 7}C{sub 3} and Cr{sub 3}C{sub 2} formed in the reaction layer of brazing alloy was the main reason for improving the bonding strength of Ni-Cr alloy to the diamond grits. A reaction layer of diamond may be a graphitization layer formed on the surface of diamond under high temperature brazing. The reaction layer of brazing alloy and steel substrate was the co-diffusion of Ni, Cr and Fe between the brazing alloy and the steel substrate. The life and sharpness of brazed diamond boring drill bits fabricated in this study were superior to the electroplated one in the market owing to its high protrusion and bonding strength.

  2. Establishment of a permeability/porosity equation for salt grit and damming materials

    International Nuclear Information System (INIS)

    Fein, E.; Mueller-Lyda, I.; Storck, R.

    1996-09-01

    The flow resistance of stowing and sealing materials hinder the transport of brines in an ultimate storage site in salt rock strata. This effect can be seen when brines flow into the storage areas and when contaminated brines are pressed out of the underground structure. The main variable determining flow resistance is permeability. The convergence process induced by rock pressure reduces the size of the available residual cavern and also the permeability of the stowing and sealing materials. In the long-term safety analyses carried out so far, the interdependence between porosity and permeability in the case of salt grit was commonly described by a power function. The present investigation uses the data available until the end of 1994 to derive an improved relation between permeability and porosity for salt grit stowing material. The results obtained show that the power function used until now is still applicable with only a slight modification of parameters. In addition, the statistical distribution functions of the correlated parameters of the permeability/porosity relation were determined for the first time for a probabilistic safety analysis. (orig./DG) [de

  3. Flow and Grit by Design: Exploring Gamification in Facilitating Adherence to Swallowing Therapy.

    Science.gov (United States)

    Constantinescu, Gabriela; Rieger, Jana; Mummery, Kerry; Hodgetts, William

    2017-11-08

    Delivery of swallowing therapy is faced with challenges regarding access to in-clinic services and adherence to prescribed home programs. Mobile health (mHealth) technologies are being developed at a rapid pace to address these difficulties. Whereas some benefits to using these modern tools for therapy are obvious (e.g., electronic reminders), other advantages are not as well understood. One example is the potential for mHealth devices and apps to enhance adherence to treatment regimens. This article introduces a number of psychological concepts that relate to adherence and that can be leveraged by mHealth. Elements that contribute to flow (optimal experience) during an activity and those that reinforce grit (perseverance to achieve a long-term goal) can be used to engage patients in their own rehabilitation. The experience of flow can be targeted by presenting the rehabilitation exercise as an optimally challenging game, one that offers a match between challenge and ability. Grit can be supported by reinforcing routine and by varying the therapy experience using different games. A combination of hardware and software design approaches have the potential to transform uninteresting and repetitive activities, such as those that make up swallowing therapy regimens, into engaging ones. The field of gamification, however, is still developing, and gamified mHealth apps will need to withstand scientific testing of their claims and demonstrate effectiveness in all phases of outcome research.

  4. Rough Surface Contact

    Directory of Open Access Journals (Sweden)

    T Nguyen

    2017-06-01

    Full Text Available This paper studies the contact of general rough curved surfaces having nearly identical geometries, assuming the contact at each differential area obeys the model proposed by Greenwood and Williamson. In order to account for the most general gross geometry, principles of differential geometry of surface are applied. This method while requires more rigorous mathematical manipulations, the fact that it preserves the original surface geometries thus makes the modeling procedure much more intuitive. For subsequent use, differential geometry of axis-symmetric surface is considered instead of general surface (although this “general case” can be done as well in Chapter 3.1. The final formulas for contact area, load, and frictional torque are derived in Chapter 3.2.

  5. Roughness Effects on Fretting Fatigue

    Science.gov (United States)

    Yue, Tongyan; Abdel Wahab, Magd

    2017-05-01

    Fretting is a small oscillatory relative motion between two normal loaded contact surfaces. It may cause fretting fatigue, fretting wear and/or fretting corrosion damage depending on various fretting couples and working conditions. Fretting fatigue usually occurs at partial slip condition, and results in catastrophic failure at the stress levels below the fatigue limit of the material. Many parameters may affect fretting behaviour, including the applied normal load and displacement, material properties, roughness of the contact surfaces, frequency, etc. Since fretting damage is undesirable due to contacting, the effect of rough contact surfaces on fretting damage has been studied by many researchers. Experimental method on this topic is usually focusing on rough surface effects by finishing treatment and random rough surface effects in order to increase fretting fatigue life. However, most of numerical models on roughness are based on random surface. This paper reviewed both experimental and numerical methodology on the rough surface effects on fretting fatigue.

  6. Grit and the Information Systems Student: A Discipline-Specific Examination of Perseverance and Passion for Long Term Goals

    Science.gov (United States)

    Brooks, Nita G.; Seipel, Scott J.

    2018-01-01

    Grit has been highlighted in recent research as a distinct trait believed to be associated with performance and success factors above and beyond those explained by cognitive ability. It focuses on the dedication required to meet long-term goals and is represented by two subscales: consistency of interest and perseverance of effort. The overall…

  7. Uso do resíduo industrial grits em pavimentos de estradas florestais: influência do período de cura na resistência mecânica e expansão de misturas solo-grits compactadas Use of industrial grits in forest road pavements: influence of curing times on the mechanical strength and swelling of compacted soil-grits mixtures

    Directory of Open Access Journals (Sweden)

    Reginaldo Sérgio Pereira

    2006-10-01

    Full Text Available Analisou-se a influência do teor de estabilizante, da energia de compactação e do período de cura na resistência mecânica e expansão de dois solos da Zona da Mata Norte de Minas Gerais. As amostras de solos residuais de gnaisse coletadas na cidade de Viçosa, MG, Brasil, respectivamente, de texturas argilo-areno-siltosa e areno-argilo-siltosa, foram denominadas solos 1 e 2. Empregou-se como estabilizante químico o resíduo "grits" fornecido pela empresa de Celulose Nipo Brasileira (CENIBRA; os teores, em massa, de 4, 8, 12, 16, 20, 24 e 28% desse resíduo foram utilizados nas misturas solo-"grits". Corpos-de-prova das misturas solo-"grits" foram compactados nos teores ótimos de umidade relativos às energias de compactação dos ensaios Proctor intermediário e modificado e curados por 0, 7, 28 e 90 dias. Avaliou-se a resistência mecânica dos solos e misturas através dos seguintes parâmetros: (a índice de suporte Califórnia (ISC ou CBR, resistência à compressão não confinada (RCNC e resistência à tração em compressão diametral (Rt. Os resultados permitiram concluir que todos os parâmetros considerados na análise influenciaram, significativamente, a resistência mecânica das misturas solo-"grits", sendo o comportamento das misturas solo 1-"grits" influenciado, também, pelo teor de sódio presente na constituição química do "grits".This paper addresses the influence of stabilizer content, compaction effort and curing time on the mechanical strength and swelling of two soils from the "Zona da Mata Norte" region, State of Minas Gerais, Brazil. Two residual gneiss soils from the municipality of Viçosa, Brazil, silt-sand-clay and silt-clay-sandy soils named soils 1 and 2, respectively, were used in this study. Industrial grits provided by Celulose Nipo Brasileira - CENIBRA was used as stabilizer, with contents ranging from 4 to 28 % regarding soil dry mass. Specimens of soil-grits mixtures were compacted at the

  8. Electrotactile Feedback for Handheld Devices with Touch Screen and Simulation of Roughness.

    Science.gov (United States)

    Altinsoy, M E; Merchel, S

    2012-01-01

    We present a novel electrotactile display that can be integrated into current handheld devices with touch screens. In this display, tactile information is presented to the fingertip of the user by transmitting small currents through electrodes. Experiments were conducted to investigate the perception of simulated textures using this electrotactile display technique. One fundamental feature of texture, which is the focus of this study, is roughness. The aim of the first experiment was to investigate the relationship between electrotactile stimulation parameters such as current and pulse frequency and the perception of roughness. An increase in the current magnitude resulted in an increase in perceived roughness. The aim of the second experiment was to investigate parameter combinations of electrotactile stimuli can be used to simulate textures. Subjects adjusted the intensity and frequency of the current stimuli until the simulated textures were perceived as being equal to reference textures such as sandpapers of varying grit numbers and grooved woods with varying groove widths. Subjects tended to find an electrotactile stimulus with a high current magnitude and a low pulse frequency more suitable to represent rough surfaces. They tended to find just-perceptible current magnitudes suitable for very smooth surfaces and did not show a preference for any frequency.

  9. MONITORAMENTO DE FUNGOS EM MILHO EM GRÃO, GRITS E FUBÁ

    OpenAIRE

    MÁRCIA, B.A.; LÁZZARI, F.A.

    1998-01-01

    O conhecimento de como a qualidade sanitária da matéria-prima afeta a qualidade dos seus subprodutos é muito importante para a indústria e para o consumidor. Para tanto foram analisadas 81 amostras de milho em grão, 81 de grits (canjica) e 81 de fubá coletadas semanalmente antes e após o processamento, durante aproximadamente 4 meses, para determinar a contaminação interna dos grãos por fungos. Os grãos destas amostras foram lavados externamente com uma solução de hipoclorito de sódio à 2% e ...

  10. Characterization of steel grit recovered from ornamental rocks waste by magnetic separation

    International Nuclear Information System (INIS)

    Junca, E.; Telles, V.B.; Rodrigues, G.F.; Oliveira, J.R. de; Tenorio, J.A.S.

    2010-01-01

    The aim of this work is characterization of steel grit recovered from ornamental rock waste by magnetic separation. The magnetic separation was realized in three steps: first, using a high intensity wet magnetic separator, which used only the remaining magnetic field of equipment. In the second step, the magnetic material obtained in the first phase was subjected to a new manual magnetic separation using rare earth magnets. In a third step, magnetic material obtained with rare earth magnets was subjected to manual magnetic separation using ferrite magnets. After the magnetic separation, the material was sent to characterization which was obtained by chemical analysis, scanning electron microscopy, X-ray diffraction and size analysis. The size analysis showed that the concentrate range from 0,5 to 563,67 μm with 4 wt.% over 100 μm and content metallic iron of 93 wt%. (author)

  11. Variations in roughness predictions (flume experiments)

    NARCIS (Netherlands)

    Noordam, Daniëlle; Blom, Astrid; van der Klis, H.; Hulscher, Suzanne J.M.H.; Makaske, A.; Wolfert, H.P.; van Os, A.G.

    2005-01-01

    Data of flume experiments with bed forms are used to analyze and compare different roughness predictors. In this study, the hydraulic roughness consists of grain roughness and form roughness. We predict the grain roughness by means of the size of the sediment. The form roughness is predicted by

  12. MONITORAMENTO DE FUNGOS EM MILHO EM GRÃO, GRITS E FUBÁ

    Directory of Open Access Journals (Sweden)

    MÁRCIA B.A.

    1998-01-01

    Full Text Available O conhecimento de como a qualidade sanitária da matéria-prima afeta a qualidade dos seus subprodutos é muito importante para a indústria e para o consumidor. Para tanto foram analisadas 81 amostras de milho em grão, 81 de grits (canjica e 81 de fubá coletadas semanalmente antes e após o processamento, durante aproximadamente 4 meses, para determinar a contaminação interna dos grãos por fungos. Os grãos destas amostras foram lavados externamente com uma solução de hipoclorito de sódio à 2% e semeados em dois meios de cultura, Ágar Batata Dextrose e Ágar Suco de Tomate. O fubá não sofreu lavagem sendo colocado pequenas porções diretamente sobre os meios de cultura. Após a incubação à 25° C durante 4 a 7 dias, os fungos foram contados e identificados. Os fungos encontrados pertenciam aos gêneros Aspergillus, Fusarium, Penicillium, Mucor e Rhizopus. Amostras de fubá apresentaram a maior porcentagem de infecção fúngica, provavelmente originada da matéria prima e/ou das condições de processamento e/ou armazenamento do mesmo. Os fungos isolados das amostras de milho em grão, grits e fubá estão normalmente presentes em produtos e subprodutos armazenados, e alguns deles podem ser toxigênicos e vir a causar sérios problemas à saúde humana.

  13. Aplicações de misturas solo-"grits" em estradas florestais: resistência mecânica via CBR Application of soil-grits mixtures in forest roads: mechanical strength via CBR test

    Directory of Open Access Journals (Sweden)

    Reginaldo Sérgio Pereira

    2006-08-01

    Full Text Available Analisaram-se as potencialidades de emprego do resíduo sólido industrial "grits", oriundo da indústria de celulose, como agente estabilizante de dois solos da Zona da Mata Norte de Minas Gerais, Brasil, para fins de emprego em estradas florestais. Os solos estudados englobaram um residual maduro, de textura argilo-areno-siltosa, e um residual jovem, de textura areno-silto-argilosa. Para tanto, prepararam-se misturas envolvendo solos e o resíduo nos quantitativos de 4, 8, 12, 16, 20, 24 e 28% em relação às massas de solo seco. Fez-se uso do ensaio CBR para avaliar as características de resistência e expansão das misturas. A avaliação dos resultados do estudo permite concluir que o resíduo "grits" apresentou potencial significativo como estabilizante dos solos, observando-se que: (i a adição de "grits" aos solos foi responsável por ganhos nas suas resistências mecânicas, obtendo-se melhores resultados com o solo de textura areno-silto-argilosa; (ii com relação à expansão medida no ensaio CBR, observaram-se pequenos acréscimos para o solo de textura argilo-areno-siltosa e decréscimos para o solo de textura areno-silto-argilosa, com aumentos no teor de "grits"; e (iii as misturas solo-"grits" não responderam bem ao aumento da energia de compactação, quanto aos parâmetros CBR e expansãoCBR.This paper is directed to forest road engineering applications, and address the potentialities of using an industrial solid waste from the cellulose industry, named grits, in the stabilization process of two soils from Zona da Mata Norte of Minas Gerais States, Brazil. Soil types tested comprised a mature residual silty-sandy-clay and a young residual clayey-silty-sand. Soil-grits mixtures were prepared at 4, 8, 12, 16, 20, 24 and 28 % stabilizer contents referred to soil dry masses. Mechanical strength and swelling parameters were determined by CBR (California Bearing Ratio tests. The laboratory testing program data supported that

  14. Comparison of vegetation roughness descriptions

    NARCIS (Netherlands)

    Augustijn, Dionysius C.M.; Huthoff, Freek; van Velzen, E.H.; Altinakar, M.S.; Kokpinar, M.A.; Aydin, I.; Cokgor, S.; Kirkgoz, S.

    2008-01-01

    Vegetation roughness is an important parameter in describing flow through river systems. Vegetation impedes the flow, which affects the stage-discharge curve and may increase flood risks. Roughness is often used as a calibration parameter in river models, however when vegetation is allowed to

  15. Bankruptcy Prediction with Rough Sets

    NARCIS (Netherlands)

    J.C. Bioch (Cor); V. Popova (Viara)

    2001-01-01

    textabstractThe bankruptcy prediction problem can be considered an or dinal classification problem. The classical theory of Rough Sets describes objects by discrete attributes, and does not take into account the order- ing of the attributes values. This paper proposes a modification of the Rough Set

  16. Generalizing roughness: experiments with flow-oriented roughness

    Science.gov (United States)

    Trevisani, Sebastiano

    2015-04-01

    Surface texture analysis applied to High Resolution Digital Terrain Models (HRDTMs) improves the capability to characterize fine-scale morphology and permits the derivation of useful morphometric indexes. An important indicator to be taken into account in surface texture analysis is surface roughness, which can have a discriminant role in the detection of different geomorphic processes and factors. The evaluation of surface roughness is generally performed considering it as an isotropic surface parameter (e.g., Cavalli, 2008; Grohmann, 2011). However, surface texture has often an anisotropic character, which means that surface roughness could change according to the considered direction. In some applications, for example involving surface flow processes, the anisotropy of roughness should be taken into account (e.g., Trevisani, 2012; Smith, 2014). Accordingly, we test the application of a flow-oriented directional measure of roughness, computed considering surface gravity-driven flow. For the calculation of flow-oriented roughness we use both classical variogram-based roughness (e.g., Herzfeld,1996; Atkinson, 2000) as well as an ad-hoc developed robust modification of variogram (i.e. MAD, Trevisani, 2014). The presented approach, based on a D8 algorithm, shows the potential impact of considering directionality in the calculation of roughness indexes. The use of flow-oriented roughness could improve the definition of effective proxies of impedance to flow. Preliminary results on the integration of directional roughness operators with morphometric-based models, are promising and can be extended to more complex approaches. Atkinson, P.M., Lewis, P., 2000. Geostatistical classification for remote sensing: an introduction. Computers & Geosciences 26, 361-371. Cavalli, M. & Marchi, L. 2008, "Characterization of the surface morphology of an alpine alluvial fan using airborne LiDAR", Natural Hazards and Earth System Science, vol. 8, no. 2, pp. 323-333. Grohmann, C

  17. Friction and Wear of Metals With a Single-Crystal Abrasive Grit of Silicon Carbide - Effect of Shear Strength of Metal

    National Research Council Canada - National Science Library

    Miyoshi, Kazuhisa

    1978-01-01

    An investigation was conducted to examine the removal and plastic deformation of metal as a function of the metal properties when the metal is in sliding contact with a single-crystal abrasive grit of silicon carbide...

  18. Armor Plate Surface Roughness Measurements

    National Research Council Canada - National Science Library

    Stanton, Brian; Coburn, William; Pizzillo, Thomas J

    2005-01-01

    ...., surface texture and coatings) that could become important at high frequency. We measure waviness and roughness of various plates to know the parameter range for smooth aluminum and rolled homogenous armor (RHA...

  19. Effect of Polishing Systems on Surface Roughness and Topography of Monolithic Zirconia.

    Science.gov (United States)

    Goo, C L; Yap, Auj; Tan, Kbc; Fawzy, A S

    2016-01-01

    This study evaluated the effect of different chairside polishing systems on the surface roughness and topography of monolithic zirconia. Thirty-five monolithic zirconia specimens (Lava PLUS, 3M ESPE) were fabricated and divided into five groups of seven and polished with the following: Group 1 (WZ)-Dura white stone followed by Shofu zirconia polishing kit; Group 2 (SZ)-Shofu zirconia polishing kit; Group 3 (CE)-Ceramiste porcelain polishers; Group 4 (CM)-Ceramaster porcelain polishers; and Group 5 (KZ)-Komet ZR zirconia polishers. All specimens were ground with a fine-grit diamond bur prior to polishing procedures to simulate clinical finishing. Baseline and post-polishing profilometric readings were recorded and delta Ra values (difference in mean surface roughness before and after polishing) were computed and analyzed using one-way analysis of variance and Scheffe post hoc test (pSEM) images of the ground but unpolished and polished specimens were acquired. Delta Ra values ranged from 0.146 for CE to 0.400 for KZ. Delta Ra values for KZ, WZ, and SZ were significantly greater than for CE. Significant differences in delta Ra values were also observed between KZ and CM. The SEM images obtained were consistent with the profilometric findings. Diamond-impregnated polishing systems were more effective than silica carbide-impregnated ones in reducing the surface roughness of ground monolithic zirconia.

  20. Gritty people try harder: grit and effort-related cardiac autonomic activity during an active coping challenge.

    Science.gov (United States)

    Silvia, Paul J; Eddington, Kari M; Beaty, Roger E; Nusbaum, Emily C; Kwapil, Thomas R

    2013-05-01

    Grit, a recently proposed personality trait associated with persistence for long-range goals, predicts achievement in a wide range of important life outcomes. Using motivational intensity theory, the present research examined the physiological underpinnings of grit during an active coping task. Forty young adults completed the Short Grit Scale and worked on a self-paced mental effort task. Effort-related autonomic nervous system (ANS) activity was assessed using impedance cardiography, which yielded measures of sympathetic activity (pre-ejection period; PEP) and parasympathetic activity (respiratory sinus arrhythmia; RSA). Multilevel models revealed that people high on the Perseverance of Effort subscale showed autonomic coactivation: both PEP and RSA became stronger during the task, reflecting higher activity of both ANS divisions. The Consistency of Interest subscale, in contrast, predicted only weaker sympathetic activity (slower PEP). Taken together, the findings illuminate autonomic processes associated with how "gritty" people pursue goals, and they suggest that more attention should be paid to the facets' distinct effects. Copyright © 2013 Elsevier B.V. All rights reserved.

  1. Fate of Fusarium mycotoxins in maize flour and grits during extrusion cooking.

    Science.gov (United States)

    Scudamore, Keith A; Guy, Robin C E; Kelleher, Brian; MacDonald, Susan J

    2008-11-01

    Extrusion technology is used widely in the manufacture of a range of breakfast cereals and snacks for human consumption and animal feeds. To minimise consumer exposure to mycotoxins, the levels of deoxynivalenol (DON) and zearalenone (ZON) in cereals/cereal products and fumonisins B(1) and B(2) (FB(1) and FB(2)) in maize are controlled by European Union legislation. Relatively few studies, however, have examined the loss of Fusarium mycotoxins during processing. The behaviour of FB(1), FB(2) and fumonisin B(3) (FB(3)), DON and ZON during extrusion of naturally contaminated maize flour and maize grits is examined using pilot-scale equipment. DON and ZON are relatively stable during extrusion cooking but the fumonisins are lost to varying degrees. There is some loss of ZON when present in low concentrations and extruded at higher moisture contents. The presence of additives, such as reducing sugars and sodium chloride, can also affect mycotoxin levels. Moisture content of the cereal feed during extrusion is important and has a greater effect than temperature, particularly on the loss of fumonisins at the lower moistures. The effects are complex and not easy to explain, although more energy input to the extruder is required for drier materials. However, on the basis of these studies, the relationship between the concentration of Fusarium toxins in the raw and finished product is toxin- and process-dependent.

  2. Suplementasi Tepung Putih Telur untuk Memperbaiki Nilai Nutrisi Snack Ekstrusi Berbahan Grits Jagung

    Directory of Open Access Journals (Sweden)

    Budiman

    2009-12-01

    Full Text Available Snack is popular for children and adult. It could be made by extrusion process. Snack is low in protein content because it is made up of cereal such as rice and corn. On the basis of nutritional and functional properties, egg was used in food industries. The objectives of the research were to analyze the nutrient content and in vitro digestibility of extruded snack from corn grits which was supplemented by egg white powder as a protein source. Randomized complete block design was used in this experiment with production periods as block. Water content was not significantly different between treatments. Supplementation with 10% egg white powder significantly increased the fat content of extrusion snack. Protein content and digestible protein increased significantly as increasing of egg white powder added. Protein digestibility of products with 10%, 15%, and 20% of egg white addition was significantly lower than those added with 0% and 5% egg white. Protein, fat, and carbohydrate linkage had formed porous product. This linkage affects product nutritive content and digestibility.

  3. Stochastic control with rough paths

    International Nuclear Information System (INIS)

    Diehl, Joscha; Friz, Peter K.; Gassiat, Paul

    2017-01-01

    We study a class of controlled differential equations driven by rough paths (or rough path realizations of Brownian motion) in the sense of Lyons. It is shown that the value function satisfies a HJB type equation; we also establish a form of the Pontryagin maximum principle. Deterministic problems of this type arise in the duality theory for controlled diffusion processes and typically involve anticipating stochastic analysis. We make the link to old work of Davis and Burstein (Stoch Stoch Rep 40:203–256, 1992) and then prove a continuous-time generalization of Roger’s duality formula [SIAM J Control Optim 46:1116–1132, 2007]. The generic case of controlled volatility is seen to give trivial duality bounds, and explains the focus in Burstein–Davis’ (and this) work on controlled drift. Our study of controlled rough differential equations also relates to work of Mazliak and Nourdin (Stoch Dyn 08:23, 2008).

  4. Heat transfer from rough surfaces

    International Nuclear Information System (INIS)

    Dalle Donne, M.

    1977-01-01

    Artificial roughness is often used in nuclear reactors to improve the thermal performance of the fuel elements. Although these are made up of clusters of rods, the experiments to measure the heat transfer and friction coefficients of roughness are performed with single rods contained in smooth tubes. This work illustrated a new transformation method to obtain data applicable to reactor fuel elements from these annulus experiments. New experimental friction data are presented for ten rods, each with a different artificial roughness made up of two-dimensional rectangular ribs. For each rod four tests have been performed, each in a different outer smooth tube. For two of these rods, each for two different outer tubes, heat transfer data are also given. The friction and heat transfer data, transformed with the present method, are correlated by simple equations. In the paper, these equations are applied to a case typical for a Gas Cooled Fast Reactor fuel element. (orig.) [de

  5. Stochastic control with rough paths

    Energy Technology Data Exchange (ETDEWEB)

    Diehl, Joscha [University of California San Diego (United States); Friz, Peter K., E-mail: friz@math.tu-berlin.de [TU & WIAS Berlin (Germany); Gassiat, Paul [CEREMADE, Université Paris-Dauphine, PSL Research University (France)

    2017-04-15

    We study a class of controlled differential equations driven by rough paths (or rough path realizations of Brownian motion) in the sense of Lyons. It is shown that the value function satisfies a HJB type equation; we also establish a form of the Pontryagin maximum principle. Deterministic problems of this type arise in the duality theory for controlled diffusion processes and typically involve anticipating stochastic analysis. We make the link to old work of Davis and Burstein (Stoch Stoch Rep 40:203–256, 1992) and then prove a continuous-time generalization of Roger’s duality formula [SIAM J Control Optim 46:1116–1132, 2007]. The generic case of controlled volatility is seen to give trivial duality bounds, and explains the focus in Burstein–Davis’ (and this) work on controlled drift. Our study of controlled rough differential equations also relates to work of Mazliak and Nourdin (Stoch Dyn 08:23, 2008).

  6. Information Measures of Roughness of Knowledge and Rough Sets for Incomplete Information Systems

    Institute of Scientific and Technical Information of China (English)

    LIANG Ji-ye; QU Kai-she

    2001-01-01

    In this paper we address information measures of roughness of knowledge and rough sets for incomplete information systems. The definition of rough entropy of knowledge and its important properties are given. In particular, the relationship between rough entropy of knowledge and the Hartley measure of uncertainty is established. We show that rough entropy of knowledge decreases monotonously as granularity of information become smaller. This gives an information interpretation for roughness of knowledge. Based on rough entropy of knowledge and roughness of rough set. a definition of rough entropy of rough set is proposed, and we show that rough entropy of rough set decreases monotonously as granularity of information become smaller. This gives more accurate measure for roughness of rough set.

  7. Does Surface Roughness Amplify Wetting?

    Czech Academy of Sciences Publication Activity Database

    Malijevský, Alexandr

    2014-01-01

    Roč. 141, č. 18 (2014), s. 184703 ISSN 0021-9606 R&D Projects: GA ČR GA13-09914S Institutional support: RVO:67985858 Keywords : density functional theory * wetting * roughness Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 2.952, year: 2014

  8. Calibration of surface roughness standards

    DEFF Research Database (Denmark)

    Thalmann, R.; Nicolet, A.; Meli, F.

    2016-01-01

    organisations. Five surface texture standards of different type were circulated and on each of the standards several roughness parameters according to the standard ISO 4287 had to be determined. 32 out of 395 individual results were not consistent with the reference value. After some corrective actions...

  9. Fuzzy Rough Ring and Its Prop erties

    Institute of Scientific and Technical Information of China (English)

    REN Bi-jun; FU Yan-ling

    2013-01-01

    This paper is devoted to the theories of fuzzy rough ring and its properties. The fuzzy approximation space generated by fuzzy ideals and the fuzzy rough approximation operators were proposed in the frame of fuzzy rough set model. The basic properties of fuzzy rough approximation operators were analyzed and the consistency between approximation operators and the binary operation of ring was discussed.

  10. Human roughness perception and possible factors effecting roughness sensation.

    Science.gov (United States)

    Aktar, Tugba; Chen, Jianshe; Ettelaie, Rammile; Holmes, Melvin; Henson, Brian

    2017-06-01

    Surface texture sensation is significant for business success, in particular for solid surfaces for most of the materials; including foods. Mechanisms of roughness perception are still unknown, especially under different conditions such as lubricants with varying viscosities, different temperatures, or under different force loads during the observation of the surface. This work aims to determine the effect of those unknown factors, with applied sensory tests on 62 healthy participants. Roughness sensation of fingertip was tested under different lubricants including water and diluted syrup solutions at room temperature (25C) and body temperature (37C) by using simple pair-wise comparison to observe the just noticeable difference threshold and perception levels. Additionally, in this research applied force load during roughness observation was tested with pair-wise ranking method to illustrate its possible effect on human sensation. Obtained results showed that human's capability of roughness discrimination reduces with increased viscosity of the lubricant, where the influence of the temperature was not found to be significant. Moreover, the increase in the applied force load showed an increase in the sensitivity of roughness discrimination. Observed effects of the applied factors were also used for estimating the oral sensation of texture during eating. These findings are significant for our fundamental understanding to texture perception, and for the development of new food products with controlled textural features. Texture discrimination ability, more specifically roughness discrimination capability, is a significant factor for preference and appreciation for a wide range of materials, including food, furniture, or fabric. To explore the mechanism of sensation capability through tactile senses, it is necessary to identify the relevant factors and define characteristics that dominate the process involved. The results that will be obtained under these principles

  11. Multiscale Analysis of the Roughness Effect on Lubricated Rough Contact

    OpenAIRE

    Demirci , Ibrahim; MEZGHANI , Sabeur; YOUSFI , Mohammed; El Mansori , Mohamed

    2014-01-01

    Determining friction is as equally essential as determining the film thickness in the lubricated contact, and is an important research subject. Indeed, reduction of friction in the automotive industry is important for both the minimization of fuel consumption as well as the decrease in the emissions of greenhouse gases. However, the progress in friction reduction has been limited by the difficulty in understanding the mechanism of roughness effects on friction. It was observed that micro-surf...

  12. True Grit: Trait-level Perseverance and Passion for Long-term Goals Predicts Effectiveness and Retention among Novice Teachers.

    Science.gov (United States)

    Robertson-Kraft, Claire; Duckworth, Angela Lee

    2014-01-01

    Surprisingly little progress has been made in linking teacher effectiveness and retention to factors observable at the time of hire. The rigors of teaching, particularly in low-income school districts, suggest the importance of personal qualities that have so far been difficult to measure objectively. In this study, we examine the predictive validity of personal qualities not typically collected by school districts during the hiring process. Specifically, we use a psychological framework to explore how biographical data on grit, a disposition toward perseverance and passion for long-term goals, explains variance in novice teachers' effectiveness and retention. In two prospective, longitudinal samples of novice teachers assigned to schools in low-income districts (N = 154 and N = 307, respectively), raters blind to outcomes followed a 7-point rubric to rate grit from information on college activities and work experience extracted from teachers' résumés. We used independent-samples t-tests and binary logistic regression models to predict teacher effectiveness and retention from these grit ratings as well as from other information (e.g., SAT scores, college GPA, interview ratings of leadership potential) available at the time of hire. Grittier teachers outperformed their less gritty colleagues and were less likely to leave their classrooms mid-year. Notably, no other variables in our analysis predicted either effectiveness or retention. These findings contribute to a better understanding of what leads some novice teachers to outperform others and remain committed to the profession. In addition to informing policy decisions surrounding teacher recruitment and development, this investigation highlights the potential of a psychological framework to explain why some individuals are more successful than others in meeting the rigorous demands of teaching.

  13. Possibilities of structure stabilisation in saliniferous formations using salt grit as a filling material; Moeglichkeiten der Gefuegestabilisierung von Salzgrusversatz

    Energy Technology Data Exchange (ETDEWEB)

    Becker, Sebastian; Gruner, Matthias; Mischo, Helmut [TU Bergakademie Freiberg (Germany). Inst. fuer Bergbau und Spezialtiefbau

    2014-09-15

    The final disposal of high-active wastes in deep geological formations is an issue of great national and international import. On account of its good thermal conductivity and creep capability much research is currently focussed on sand as a host rock material. After the emplacement of wastes in abandoned mining cavities these must be sealed up to prevent fluids from coming into contact with the wastes. This must be done using materials that are either native or similar to the materials of the host formation. A particularly suitable material in the case of saliniferous formations is salt grit. Up to this point investigations have primarily been focused on preparing a suitable salt grit material and the rheological properties of the binding agent. This article presents and interprets the results of preliminary experiments on the miscibility of salt grit and binding agent suspensions. The MgO and CaSO{sub 4}-based binding agent systems analysed proved to be suitable. Among the MgO binding agents a composition of 3:1:8 was found to be more suitable than one of 5:1:8 on account of its lower initial viscosity. This reduces the amount of mixing required for wetting the material across all grain sizes, improving the chances of success. In the case of the two semihydrates of CaSO{sub 4} both the α and the β semihydrate proved suitable. This is due to a low fluid content which still also allows for a sufficiently low viscosity of the binding agent suspensions.

  14. Comparison of different finishing/polishing systems on surface roughness and gloss of resin composites.

    Science.gov (United States)

    Antonson, Sibel A; Yazici, A Rüya; Kilinc, Evren; Antonson, Donald E; Hardigan, Patrick C

    2011-07-01

    The aim of this study was to compare four finishing/polishing systems (F/P) on surface roughness and gloss of different resin composites. A total of 40 disc samples (15 mm × 3 mm) were prepared from a nanofill - Filtek Supreme Plus (FS) and a micro-hybrid resin composite - Esthet-X (EX). Following 24h storage in 37°C water, the top surfaces of each sample were roughened using 120-grit sandpaper. Baseline measurements of surface roughness (Ra, μm) and gloss were recorded. Each composite group was divided into four F/P disk groups: Astropol[AP], Enhance/PoGo[EP], Sof-Lex[SL], and an experimental disk system, EXL-695[EXL] (n=5). The same operator finished/polished all samples. One sample from each group was evaluated under SEM. Another blinded-operator conducted postoperative measurements. Results were analysed by two-way ANOVA, two interactive MANOVA and Tukey's t-test (p0.01). In gloss, FS composite with the EXL-695 system provided a significantly higher gloss (pgloss (pgloss. SEM evaluations revealed that the EX surface contained more air pockets but F/P systems were compatible. Copyright © 2011 Elsevier Ltd. All rights reserved.

  15. Gloss and surface roughness produced by polishing kits on resin composites.

    Science.gov (United States)

    Sadidzadeh, Ramtin; Cakir, Deniz; Ramp, Lance C; Burgess, John O

    2010-08-01

    To compare in vitro the surface roughness (Ra) and gloss (G) produced by three conventional and one experimental polishing kits on four resin composites. 24 discs were prepared (d = 12 mm, t = 4 mm) for each resin composite: Filtek Supreme Plus Body/A2 (FSB), Yellow Translucent (FST), Heliomolar/A2 (HM), and EsthetX/A2 (EX) following the manufacturers' instructions. They were finished with 320 grit silicon carbide paper for 80 seconds each. Polishing systems: Sof-Lex, Enhance-Pogo, Astropol and Experimental Discs/EXL-695, were applied following manufacturers' instructions. Each specimen was ultrasonically cleaned with distilled water and dried. Gloss and Ra were measured with a small area glossmeter (Novo-curve) and non-contact profilometer (Proscan 2000) following ISO 4288, respectively. The results were evaluated by two-way ANOVA followed by separate one-way ANOVA and Tukey/Kramer test (P = 0.05). There was a significant interaction of surface roughness and gloss between the composites and polishing systems (P gloss was obtained for FSB composite polished with the Experimental kit. The experimental polishing system produced smoothest surfaces (P gloss (P < 0.05).

  16. Effects of small-grit grinding and glazing on mechanical behaviors and ageing resistance of a super-translucent dental zirconia.

    Science.gov (United States)

    Lai, Xuan; Si, Wenjie; Jiang, Danyu; Sun, Ting; Shao, Longquan; Deng, Bin

    2017-11-01

    The purpose of this study is to elucidate the effects of small-grit grinding on the mechanical behaviors and ageing resistance of a super-translucent dental zirconia and to investigate the necessity of glazing for the small-grit ground zirconia. Small-grit grinding was performed using two kinds of silicon carbide abrasive papers. The control group received no grinding. The unground surfaces and the ground surfaces were glazed by an experienced dental technician. Finally, the zirconia materials were thermally aged in water at 134°C for 5h. After aforementioned treatments, we observed the surface topography and the microstructures, and measured the extent of monoclinic phase, the nano-hardness and nano-modulus of the possible transformed zone and the flexural strength. Small-grit grinding changed the surface topography. The zirconia microstructure did not change obviously after surface treatments and thermal ageing; however, the glaze in contact with zirconia showed cracks after thermal ageing. Small-grit grinding did not induce a phase transformation but improved the flexural strength and ageing resistance. Glazing prevented zirconia from thermal ageing but severely diminished the flexural strength. The nano-hardness and nano-modulus of the surface layer were increased by ultrafine grinding. The results suggest that small-grit grinding is beneficial to the strength and ageing resistance of the super-translucent dental zirconia; however, glazing is not necessary and even impairs the strength for the super-translucent dental zirconia. This study is helpful to the researches about dental grinding tools and maybe useful for dentists to choose reasonable zirconia surface treatments. Copyright © 2017 Elsevier Ltd. All rights reserved.

  17. Ultrasonic backward radiation on painted rough interface

    International Nuclear Information System (INIS)

    Kwon, Yong Gyu; Yoon, Seok Soo; Kwon, Sung Duck

    2002-01-01

    The angular dependence(profile) of backscattered ultrasound was measured for steel and brass specimens with periodical surface roughness (1-71μm). Backward radiations showed more linear dependency than normal profile. Direct amplitude increased and averaging amplitude decreased with surface roughness. Painting treatment improved the linearity in direct backward radiation below roughness of 0.03. Scholte and Rayleigh-like waves were observed in the spectrum of averaging backward radiation on periodically rough surface. Painting on periodically rough surface could be used in removing the interface mode effect by periodic roughness.

  18. Influence of titanium-substrate roughness on Ca–P–O thin films grown by atomic layer deposition

    Energy Technology Data Exchange (ETDEWEB)

    Ananda Sagari, A.R., E-mail: arsagari@gmail.com [Department of Physics, P.O. Box 35 (YFL), FIN-40014 University of Jyväskylä (Finland); Malm, Jari [Department of Chemistry, P.O. Box 16100, FI-00076 Aalto University, Espoo (Finland); Laitinen, Mikko [Department of Physics, P.O. Box 35 (YFL), FIN-40014 University of Jyväskylä (Finland); Rahkila, Paavo [Department of Biology of Physical Activity, P.O. Box 35, FIN-40014 University of Jyväskylä (Finland); Hongqiang, Ma [Department of Health Sciences, P.O. Box 35 (L), FIN-40014 University of Jyväskylä (Finland); Putkonen, Matti [Department of Chemistry, P.O. Box 16100, FI-00076 Aalto University, Espoo (Finland); Beneq Oy, P.O. Box 262, FI-01511 Vantaa (Finland); Karppinen, Maarit [Department of Chemistry, P.O. Box 16100, FI-00076 Aalto University, Espoo (Finland); Whitlow, Harry J.; Sajavaara, Timo [Department of Physics, P.O. Box 35 (YFL), FIN-40014 University of Jyväskylä (Finland)

    2013-03-01

    Amorphous Ca–P–O films were deposited on titanium substrates using atomic layer deposition, while maintaining a uniform Ca/P pulsing ratio of 6/1 with varying number of atomic layer deposition cycles starting from 10 up to 208. Prior to film deposition the titanium substrates were mechanically abraded using SiC abrasive paper of 600, 1200, 2000 grit size and polished with 3 μm diamond paste to obtain surface roughness R{sub rms} values of 0.31 μm, 0.26 μm, 0.16 μm, and 0.10 μm, respectively. The composition and film thickness of as-deposited amorphous films were studied using Time-Of-Flight Elastic Recoil Detection Analysis. The results showed that uniform films could be deposited on rough metal surfaces with a clear dependence of substrate roughness on the Ca/P atomic ratio of thin films. The in vitro cell-culture studies using MC3T3 mouse osteoblast showed a greater coverage of cells on the surface polished with diamond paste in comparison to rougher surfaces after 24 h culture. No statistically significant difference was observed between Ca–P–O coated and un-coated Ti surfaces for the measured roughness value. The deposited 50 nm thick films did not dissolve during the cell culture experiment. - Highlights: ► Atomic layer deposition of Ca–P–O films on abraded Ti substrate ► Surface analysis using Time-Of-Flight Elastic Recoil Detection Analysis ► Dependence of substrate roughness on the Ca/P atomic ratio of thin films ► An increase in Ca/P atomic ratio with decreasing roughness ► Mouse osteoblast showed greater coverage of cells in polished surface.

  19. Towards predictive models for transitionally rough surfaces

    Science.gov (United States)

    Abderrahaman-Elena, Nabil; Garcia-Mayoral, Ricardo

    2017-11-01

    We analyze and model the previously presented decomposition for flow variables in DNS of turbulence over transitionally rough surfaces. The flow is decomposed into two contributions: one produced by the overlying turbulence, which has no footprint of the surface texture, and one induced by the roughness, which is essentially the time-averaged flow around the surface obstacles, but modulated in amplitude by the first component. The roughness-induced component closely resembles the laminar steady flow around the roughness elements at the same non-dimensional roughness size. For small - yet transitionally rough - textures, the roughness-free component is essentially the same as over a smooth wall. Based on these findings, we propose predictive models for the onset of the transitionally rough regime. Project supported by the Engineering and Physical Sciences Research Council (EPSRC).

  20. Rough set classification based on quantum logic

    Science.gov (United States)

    Hassan, Yasser F.

    2017-11-01

    By combining the advantages of quantum computing and soft computing, the paper shows that rough sets can be used with quantum logic for classification and recognition systems. We suggest the new definition of rough set theory as quantum logic theory. Rough approximations are essential elements in rough set theory, the quantum rough set model for set-valued data directly construct set approximation based on a kind of quantum similarity relation which is presented here. Theoretical analyses demonstrate that the new model for quantum rough sets has new type of decision rule with less redundancy which can be used to give accurate classification using principles of quantum superposition and non-linear quantum relations. To our knowledge, this is the first attempt aiming to define rough sets in representation of a quantum rather than logic or sets. The experiments on data-sets have demonstrated that the proposed model is more accuracy than the traditional rough sets in terms of finding optimal classifications.

  1. Influência do tratamento térmico do resíduo sólido industrial (Grits na resistência mecânica de um latossolo para pavimentos de estradas florestais Influence of the thermal treatment of industrial solid residue (Grits on the mechanical resistance of a latosol for forest engineering roads

    Directory of Open Access Journals (Sweden)

    Carlos Cardoso Machado

    2003-08-01

    Full Text Available Em estudos que envolvem o tratamento de solos com aditivos químicos com fins rodoviários, merecem especial importância aquelas pesquisas orientadas no sentido de descobrir novos meios de torná-los mais econômicos e, ao mesmo tempo, mais resistentes. No presente trabalho, o resíduo sólido industrial Grits, oriundo do processo de fabricação de papel e celulose, foi aplicado a um latossolo denominado ETA, característico da microrregião de Viçosa, Minas Gerais, Brasil, com o intuito de melhorar suas características mecânicas para sua aplicação em pavimentos de estradas florestais. O Grits, após receber tratamento térmico a 200, 300, 400, 500 e 600 ºC, em mufla, foi misturado no teor de 10%, em peso, ao solo anteriormente citado. Parâmetros geotécnicos, característicos dos ensaios de compactação e resistência à compressão simples, foram utilizados para avaliar o efeito do tratamento térmico nas misturas solo+10% Grits. Os resultados indicaram que o Grits tem potencial para estabilização de solos de pavimentos de estradas florestais, sendo o melhor resultado alcançado para o Grits tratado a 600 ºC, pois houve ganhos de resistência mecânica.Road engineering studies involving chemical stabilization of soils deserve special recognition mainly those directed to lowering the costs of forest engineering roads. This work focuses on soil stabilization of a characteristic Latosol from Viçosa, Minas Gerais, Brazil, herein named ETA, using a residue from paper and cellulose industry production, herein called Grits. Grits content of 10% related to soil dry weight was used throughout the study after residue thermal treatment using a furnace at 200, 300, 400, 500 and 600 ºC. Geotechnical standard parameters from compaction and unconfined compression tests were used to evaluate the effect of thermal treatment on the mechanical response of soil-Grits mixtures. Unconfined compression testing data show that Grits is a promising soil

  2. Poverty and the Ideological Imperative: A Call to Unhook from Deficit and Grit Ideology and to Strive for Structural Ideology in Teacher Education

    Science.gov (United States)

    Gorski, Paul C.

    2016-01-01

    In this article I explore the educational equity implications of three popular ideological positions that drive teachers' and teacher educators' understandings of, and responses to, poverty and economic injustice in schools: deficit ideology, grit ideology, and structural ideology. The educator's ideological position, I illustrate, determines…

  3. Computer simulations of a rough sphere fluid

    International Nuclear Information System (INIS)

    Lyklema, J.W.

    1978-01-01

    A computer simulation is described on rough hard spheres with a continuously variable roughness parameter, including the limits of smooth and completely rough spheres. A system of 500 particles is simulated with a homogeneous mass distribution at 8 different densities and for 5 different values of the roughness parameter. For these 40 physically different situations the intermediate scattering function for 6 values of the wave number, the orientational correlation functions and the velocity autocorrelation functions have been calculated. A comparison has been made with a neutron scattering experiment on neopentane and agreement was good for an intermediate value of the roughness parameter. Some often made approximations in neutron scattering experiments are also checked. The influence of the variable roughness parameter on the correlation functions has been investigated and three simple stochastic models studied to describe the orientational correlation function which shows the most pronounced dependence on the roughness. (Auth.)

  4. Axis Problem of Rough 3-Valued Algebras

    Institute of Scientific and Technical Information of China (English)

    Jianhua Dai; Weidong Chen; Yunhe Pan

    2006-01-01

    The collection of all the rough sets of an approximation space has been given several algebraic interpretations, including Stone algebras, regular double Stone algebras, semi-simple Nelson algebras, pre-rough algebras and 3-valued Lukasiewicz algebras. A 3-valued Lukasiewicz algebra is a Stone algebra, a regular double Stone algebra, a semi-simple Nelson algebra, a pre-rough algebra. Thus, we call the algebra constructed by the collection of rough sets of an approximation space a rough 3-valued Lukasiewicz algebra. In this paper,the rough 3-valued Lukasiewicz algebras, which are a special kind of 3-valued Lukasiewicz algebras, are studied. Whether the rough 3-valued Lukasiewicz algebra is a axled 3-valued Lukasiewicz algebra is examined.

  5. Uso de resíduos em pavimentos de estradas florestais: caracterização de solos e misturas solo-grits Application of waste in forest road pavements: characterization of soils and soil-grits mixtures

    Directory of Open Access Journals (Sweden)

    Reginaldo Sérgio Pereira

    2006-08-01

    Full Text Available Este artigo aborda uma etapa preliminar de um estudo direcionado às propriedades de engenharia de misturas de solos e aditivos químicos, para fins de aplicação em estradas florestais. Trabalhou-se com amostras de dois solos da Zona da Mata Norte de Minas Gerais, Brasil, de texturas arenosa e argilosa, estabilizadas com o resíduo industrial denominado "grits" proveniente de indústria de celulose. Foram realizados ensaios geotécnicos nos solos e nas misturas solo-aditivo químico, como se segue: análise granulométrica, peso específico dos sólidos, limites de Atterberg e compactação. Os resultados encontrados dos ensaios de laboratório revelaram que o resíduo apresentou bom desempenho como agente estabilizante, alterando significativamente a plasticidade e os parâmetros de compactação dos solos analisados.This paper addresses data from a research program in development on engineering properties of soil-chemical stabilizer mixtures for forest road application. Soil samples from sandy and clayey soils from the Zona da Mata Norte of Minas Gerais, Brazil, stabilized with grits (waste from cellulose industries were used throughout the study. The laboratory-testing program comprised the following geotechnical tests: sieve analysis, density of solid particles, Atterberg limits and compaction. Data supported the good behavior of waste as stabilizer agent changing significantly soil plasticity and compaction parameters.

  6. Sensing roughness and polish direction

    DEFF Research Database (Denmark)

    Jakobsen, Michael Linde; Olesen, Anders Sig; Larsen, Henning Engelbrecht

    2016-01-01

    As a part of the work carried out in a project supported by the Danish Council for Technology and Innovation, we have investigated the option of smoothing standard CNC-machined surfaces. In the process of constructing optical prototypes, involving custom-designed optics, the development cost...... and time consumption can become prohibitive in a research budget. Machining the optical surfaces directly is expensive and time consuming. Alternatively, a more standardized and cheaper machining method can be used, calling for the object to be manually polished. During the polishing process, the operator...... needs information about the RMS-value of the surface roughness and the current direction of the scratches introduced by the polishing process. The RMS-value indicates to the operator how far he is from the final finish, and the scratch orientation is often specified by the customer in order to avoid...

  7. Software testing in roughness calculation

    International Nuclear Information System (INIS)

    Chen, Y L; Hsieh, P F; Fu, W E

    2005-01-01

    A test method to determine the function quality provided by the software for roughness measurement is presented in this study. The function quality of the software requirements should be part of and assessed through the entire life cycle of the software package. The specific function, or output accuracy, is crucial for the analysis of the experimental data. For scientific applications, however, commercial software is usually embedded with specific instrument, which is used for measurement or analysis during the manufacture process. In general, the error ratio caused by the software would be more apparent especially when dealing with relatively small quantities, like the measurements in the nanometer-scale range. The model of 'using a data generator' proposed by NPL of UK was applied in this study. An example of the roughness software is tested and analyzed by the above mentioned process. After selecting the 'reference results', the 'reference data' was generated by a programmable 'data generator'. The filter function of 0.8 mm long cutoff value, defined in ISO 11562 was tested with 66 sinusoid data at different wavelengths. Test results from commercial software and CMS written program were compared to the theoretical data calculated from ISO standards. As for the filter function in this software, the result showed a significant disagreement between the reference and test results. The short cutoff feature for filtering at the high frequencies does not function properly, while the long cutoff feature has the maximum difference in the filtering ratio, which is more than 70% between the wavelength of 300 μm and 500 μm. Conclusively, the commercial software needs to be tested more extensively for specific application by appropriate design of reference dataset to ensure its function quality

  8. Simulation analysis of air flow and turbulence statistics in a rib grit roughened duct.

    Science.gov (United States)

    Vogiatzis, I I; Denizopoulou, A C; Ntinas, G K; Fragos, V P

    2014-01-01

    The implementation of variable artificial roughness patterns on a surface is an effective technique to enhance the rate of heat transfer to fluid flow in the ducts of solar air heaters. Different geometries of roughness elements investigated have demonstrated the pivotal role that vortices and associated turbulence have on the heat transfer characteristics of solar air heater ducts by increasing the convective heat transfer coefficient. In this paper we investigate the two-dimensional, turbulent, unsteady flow around rectangular ribs of variable aspect ratios by directly solving the transient Navier-Stokes and continuity equations using the finite elements method. Flow characteristics and several aspects of turbulent flow are presented and discussed including velocity components and statistics of turbulence. The results reveal the impact that different rib lengths have on the computed mean quantities and turbulence statistics of the flow. The computed turbulence parameters show a clear tendency to diminish downstream with increasing rib length. Furthermore, the applied numerical method is capable of capturing small-scale flow structures resulting from the direct solution of Navier-Stokes and continuity equations.

  9. Mineral phases of green liquor dregs, slaker grits, lime mud and wood ash of a Kraft pulp and paper mill

    Energy Technology Data Exchange (ETDEWEB)

    Martins, Fernanda Machado [Laboratorio de Quimica Mineral Aplicada, Departamento de Quimica-UFPR, Universidade Federal do Parana (UFPR), CP 19081, CEP 81531990, Curitiba-PR (Brazil); Munhoz Martins, Joaniel [Laboratorio de Analise de Minerais e Rochas (LAMIR-UFPR) (Brazil); Ferracin, Luiz Carlos [Laboratorio Quimico da Votorantin Cimentos (Brazil); Cunha, Carlos Jorge da [Laboratorio de Quimica Mineral Aplicada, Departamento de Quimica-UFPR, Universidade Federal do Parana (UFPR), CP 19081, CEP 81531990, Curitiba-PR (Brazil)]. E-mail: cjdcunha@quimica.ufpr.br

    2007-08-17

    Four residues generated in a Kraft, pulp and paper plant, were characterized by X-ray fluorescence spectroscopy (XFA), powder X-ray diffraction (XRD), thermogravimmetric analysis (TG) and Fourier transform infrared spectroscopy (FTIR). A quantitative phase composition model, that accounts for the observed data and for the physico-chemical conditions of formation, was postulated for each material. Emphasis was given on the identification of the mineral components of each material. The green liquor dregs and the lime mud contain Calcite and Gipsite. The slaker grits contains Calcite, Portlandite, Pirssonite, Larnite and Brucite. The Calcite phase, present in the dregs and in the lime mud, has small amounts of magnesium replacing calcium. The wood ash contains Quartz as the major crystalline mineral phase.

  10. Mineral phases of green liquor dregs, slaker grits, lime mud and wood ash of a Kraft pulp and paper mill

    International Nuclear Information System (INIS)

    Martins, Fernanda Machado; Munhoz Martins, Joaniel; Ferracin, Luiz Carlos; Cunha, Carlos Jorge da

    2007-01-01

    Four residues generated in a Kraft, pulp and paper plant, were characterized by X-ray fluorescence spectroscopy (XFA), powder X-ray diffraction (XRD), thermogravimmetric analysis (TG) and Fourier transform infrared spectroscopy (FTIR). A quantitative phase composition model, that accounts for the observed data and for the physico-chemical conditions of formation, was postulated for each material. Emphasis was given on the identification of the mineral components of each material. The green liquor dregs and the lime mud contain Calcite and Gipsite. The slaker grits contains Calcite, Portlandite, Pirssonite, Larnite and Brucite. The Calcite phase, present in the dregs and in the lime mud, has small amounts of magnesium replacing calcium. The wood ash contains Quartz as the major crystalline mineral phase

  11. Simplified Approach to Predicting Rough Surface Transition

    Science.gov (United States)

    Boyle, Robert J.; Stripf, Matthias

    2009-01-01

    Turbine vane heat transfer predictions are given for smooth and rough vanes where the experimental data show transition moving forward on the vane as the surface roughness physical height increases. Consiste nt with smooth vane heat transfer, the transition moves forward for a fixed roughness height as the Reynolds number increases. Comparison s are presented with published experimental data. Some of the data ar e for a regular roughness geometry with a range of roughness heights, Reynolds numbers, and inlet turbulence intensities. The approach ta ken in this analysis is to treat the roughness in a statistical sense , consistent with what would be obtained from blades measured after e xposure to actual engine environments. An approach is given to determ ine the equivalent sand grain roughness from the statistics of the re gular geometry. This approach is guided by the experimental data. A roughness transition criterion is developed, and comparisons are made with experimental data over the entire range of experimental test co nditions. Additional comparisons are made with experimental heat tran sfer data, where the roughness geometries are both regular as well a s statistical. Using the developed analysis, heat transfer calculatio ns are presented for the second stage vane of a high pressure turbine at hypothetical engine conditions.

  12. Rock discontinuity surface roughness variation with scale

    Science.gov (United States)

    Bitenc, Maja; Kieffer, D. Scott; Khoshelham, Kourosh

    2017-04-01

    ABSTRACT: Rock discontinuity surface roughness refers to local departures of the discontinuity surface from planarity and is an important factor influencing the shear resistance. In practice, the Joint Roughness Coefficient (JRC) roughness parameter is commonly relied upon and input to a shear strength criterion such as developed by Barton and Choubey [1977]. The estimation of roughness by JRC is hindered firstly by the subjective nature of visually comparing the joint profile to the ten standard profiles. Secondly, when correlating the standard JRC values and other objective measures of roughness, the roughness idealization is limited to a 2D profile of 10 cm length. With the advance of measuring technologies that provide accurate and high resolution 3D data of surface topography on different scales, new 3D roughness parameters have been developed. A desirable parameter is one that describes rock surface geometry as well as the direction and scale dependency of roughness. In this research a 3D roughness parameter developed by Grasselli [2001] and adapted by Tatone and Grasselli [2009] is adopted. It characterizes surface topography as the cumulative distribution of local apparent inclination of asperities with respect to the shear strength (analysis) direction. Thus, the 3D roughness parameter describes the roughness amplitude and anisotropy (direction dependency), but does not capture the scale properties. In different studies the roughness scale-dependency has been attributed to data resolution or size of the surface joint (see a summary of researches in [Tatone and Grasselli, 2012]). Clearly, the lower resolution results in lower roughness. On the other hand, have the investigations of surface size effect produced conflicting results. While some studies have shown a decrease in roughness with increasing discontinuity size (negative scale effect), others have shown the existence of positive scale effects, or both positive and negative scale effects. We

  13. Bed roughness experiments in supply limited conditions

    NARCIS (Netherlands)

    Spekkers, Matthieu; Tuijnder, Arjan; Ribberink, Jan S.; Hulscher, Suzanne J.M.H.; Parsons, D.R.; Garlan, T.; Best, J.L.

    2008-01-01

    Reliable roughness models are of great importance, for example, when predicting water levels in rivers. The currently available roughness models are based on fully mobile bed conditions. However, in rivers where widely graded sediments are present more or less permanent armour layers can develop

  14. Axiomatic Characterizations of IVF Rough Approximation Operators

    Directory of Open Access Journals (Sweden)

    Guangji Yu

    2014-01-01

    Full Text Available This paper is devoted to the study of axiomatic characterizations of IVF rough approximation operators. IVF approximation spaces are investigated. The fact that different IVF operators satisfy some axioms to guarantee the existence of different types of IVF relations which produce the same operators is proved and then IVF rough approximation operators are characterized by axioms.

  15. Wall roughness induces asymptotic ultimate turbulence

    NARCIS (Netherlands)

    Zhu, Xiaojue; Verschoof, Ruben Adriaan; Bakhuis, Dennis; Huisman, Sander Gerard; Verzicco, Roberto; Sun, Chao; Lohse, Detlef

    2018-01-01

    Turbulence governs the transport of heat, mass and momentum on multiple scales. In real-world applications, wall-bounded turbulence typically involves surfaces that are rough; however, characterizing and understanding the effects of wall roughness on turbulence remains a challenge. Here, by

  16. Electrochemically grown rough-textured nanowires

    International Nuclear Information System (INIS)

    Tyagi, Pawan; Postetter, David; Saragnese, Daniel; Papadakis, Stergios J.; Gracias, David H.

    2010-01-01

    Nanowires with a rough surface texture show unusual electronic, optical, and chemical properties; however, there are only a few existing methods for producing these nanowires. Here, we describe two methods for growing both free standing and lithographically patterned gold (Au) nanowires with a rough surface texture. The first strategy is based on the deposition of nanowires from a silver (Ag)-Au plating solution mixture that precipitates an Ag-Au cyanide complex during electrodeposition at low current densities. This complex disperses in the plating solution, thereby altering the nanowire growth to yield a rough surface texture. These nanowires are mass produced in alumina membranes. The second strategy produces long and rough Au nanowires on lithographically patternable nickel edge templates with corrugations formed by partial etching. These rough nanowires can be easily arrayed and integrated with microscale devices.

  17. Modeling surface roughness scattering in metallic nanowires

    Energy Technology Data Exchange (ETDEWEB)

    Moors, Kristof, E-mail: kristof@itf.fys.kuleuven.be [KU Leuven, Institute for Theoretical Physics, Celestijnenlaan 200D, B-3001 Leuven (Belgium); IMEC, Kapeldreef 75, B-3001 Leuven (Belgium); Sorée, Bart [IMEC, Kapeldreef 75, B-3001 Leuven (Belgium); Physics Department, University of Antwerp, Groenenborgerlaan 171, B-2020 Antwerpen (Belgium); KU Leuven, Electrical Engineering (ESAT) Department, Kasteelpark Arenberg 10, B-3001 Leuven (Belgium); Magnus, Wim [IMEC, Kapeldreef 75, B-3001 Leuven (Belgium); Physics Department, University of Antwerp, Groenenborgerlaan 171, B-2020 Antwerpen (Belgium)

    2015-09-28

    Ando's model provides a rigorous quantum-mechanical framework for electron-surface roughness scattering, based on the detailed roughness structure. We apply this method to metallic nanowires and improve the model introducing surface roughness distribution functions on a finite domain with analytical expressions for the average surface roughness matrix elements. This approach is valid for any roughness size and extends beyond the commonly used Prange-Nee approximation. The resistivity scaling is obtained from the self-consistent relaxation time solution of the Boltzmann transport equation and is compared to Prange-Nee's approach and other known methods. The results show that a substantial drop in resistivity can be obtained for certain diameters by achieving a large momentum gap between Fermi level states with positive and negative momentum in the transport direction.

  18. Suppression of intrinsic roughness in encapsulated graphene

    DEFF Research Database (Denmark)

    Thomsen, Joachim Dahl; Gunst, Tue; Gregersen, Søren Schou

    2017-01-01

    Roughness in graphene is known to contribute to scattering effects which lower carrier mobility. Encapsulating graphene in hexagonal boron nitride (hBN) leads to a significant reduction in roughness and has become the de facto standard method for producing high-quality graphene devices. We have...... fabricated graphene samples encapsulated by hBN that are suspended over apertures in a substrate and used noncontact electron diffraction measurements in a transmission electron microscope to measure the roughness of encapsulated graphene inside such structures. We furthermore compare the roughness...... of these samples to suspended bare graphene and suspended graphene on hBN. The suspended heterostructures display a root mean square (rms) roughness down to 12 pm, considerably less than that previously reported for both suspended graphene and graphene on any substrate and identical within experimental error...

  19. Fingerprinting the type of line edge roughness

    Science.gov (United States)

    Fernández Herrero, A.; Pflüger, M.; Scholze, F.; Soltwisch, V.

    2017-06-01

    Lamellar gratings are widely used diffractive optical elements and are prototypes of structural elements in integrated electronic circuits. EUV scatterometry is very sensitive to structure details and imperfections, which makes it suitable for the characterization of nanostructured surfaces. As compared to X-ray methods, EUV scattering allows for steeper angles of incidence, which is highly preferable for the investigation of small measurement fields on semiconductor wafers. For the control of the lithographic manufacturing process, a rapid in-line characterization of nanostructures is indispensable. Numerous studies on the determination of regular geometry parameters of lamellar gratings from optical and Extreme Ultraviolet (EUV) scattering also investigated the impact of roughness on the respective results. The challenge is to appropriately model the influence of structure roughness on the diffraction intensities used for the reconstruction of the surface profile. The impact of roughness was already studied analytically but for gratings with a periodic pseudoroughness, because of practical restrictions of the computational domain. Our investigation aims at a better understanding of the scattering caused by line roughness. We designed a set of nine lamellar Si-gratings to be studied by EUV scatterometry. It includes one reference grating with no artificial roughness added, four gratings with a periodic roughness distribution, two with a prevailing line edge roughness (LER) and another two with line width roughness (LWR), and four gratings with a stochastic roughness distribution (two with LER and two with LWR). We show that the type of line roughness has a strong impact on the diffuse scatter angular distribution. Our experimental results are not described well by the present modelling approach based on small, periodically repeated domains.

  20. Grit or Honesty-Humility? New Insights into the Moderating Role of Personality between the Health Impairment Process and Counterproductive Work Behavior.

    Science.gov (United States)

    Ceschi, Andrea; Sartori, Riccardo; Dickert, Stephan; Costantini, Arianna

    2016-01-01

    It is acknowledged that chronic job demands may be depleting workers' stamina resulting in burnout conditions and ultimately causing further health problems. This relation, known as health impairment process, has recently been considered as a possible explanation for the emergence of counterproductive work behavior (CWB). The present work aims to examine the role of two personality traits (i.e., Grit and Honesty-Humility) in this process. The results, based on a sample of 208 private service sector employees, confirm the presence of a fully mediated process and show how Honesty-Humility positively moderates the relationship between job demands and exhaustion, whereas Grit has a negative effect on the relation between exhaustion and CWB. Implications for assessment procedure and hiring decisions are discussed.

  1. Grit or Honesty-Humility? New insights into the moderating role of personality between the health impairment process and counterproductive work behavior

    Directory of Open Access Journals (Sweden)

    Andrea Ceschi

    2016-12-01

    Full Text Available It is acknowledged that chronic job demands may be depleting workers’ stamina resulting in burnout conditions and ultimately causing further health problems. This relation, known as health impairment process, has recently been considered as a possible explanation for the emergence of counterproductive work behavior (CWB. The present work aims to examine the role of two personality traits (i.e., Grit and Honesty–Humility in this process. The results, based on a sample of 208 private service sector employees, confirm the presence of a fully mediated process and show how Honesty–Humility positively moderates the relationship between job demands and exhaustion, whereas Grit has a negative effect on the relation between exhaustion and CWB. Implications for assessment procedure and hiring decisions are discussed.

  2. The Effect of Moisture Content of Maize Grits on Physicochemical Properties of Its Puffed Food Products Properties of Its Puffed Food Products

    Directory of Open Access Journals (Sweden)

    S. Sharifi

    2016-02-01

    Full Text Available In this study the effect of different levels of moisture content of maize grits (10, 13, 16 and 19% as an attribute of physicochemical properties of extruder-derived puffed products, was investigated. The results showed that with increasing maize grits' moisture content, water absorption index (WAI and water solubility index (WSI were decreased. Moreover, with changing in feed moisture content from 10 to 16%, the volume and sectional expansion index (SEI increased but further increase of moisture content to 19% caused a reduction in these parameters. The textural tests also revealed that with increase in moisture content, the compression energy (Nmm, maximum force (N and time to achieve the first major peak (s were increased but the number of peaks was decreased. With increase in the moisture content, specific mechanical energy (SME was decreased, due probably to the reduction in the viscosity of melt. With increase in the moisture content the L and b values were increased but the value of the samples were decreased due to the reduction of Maillard reaction rate. Our data confirms that the moisture content of maize grits may play an important role in the quality of produced extruded snacks and a high quality product can be achieved by optimizing this parameter. In this research, the maximum volume of the extruder product was obtained in 16% of moisture level.

  3. Surface roughness effects on turbulent Couette flow

    Science.gov (United States)

    Lee, Young Mo; Lee, Jae Hwa

    2017-11-01

    Direct numerical simulation of a turbulent Couette flow with two-dimensional (2-D) rod roughness is performed to examine the effects of the surface roughness. The Reynolds number based on the channel centerline laminar velocity (Uco) and channel half height (h) is Re =7200. The 2-D rods are periodically arranged with a streamwise pitch of λ = 8 k on the bottom wall, and the roughness height is k = 0.12 h. It is shown that the wall-normal extent for the logarithmic layer is significantly shortened in the rough-wall turbulent Couette flow, compared to a turbulent Couette flow with smooth wall. Although the Reynolds stresses are increased in a turbulent channel flow with surface roughness in the outer layer due to large-scale ejection motions produced by the 2-D rods, those of the rough-wall Couette flow are decreased. Isosurfaces of the u-structures averaged in time suggest that the decrease of the turbulent activity near the centerline is associated with weakened large-scale counter-rotating roll modes by the surface roughness. This research was supported by the National Research Foundation of Korea (NRF) funded by the Ministry of Education (NRF-2017R1D1A1A09000537) and the Ministry of Science, ICT & Future Planning (NRF-2017R1A5A1015311).

  4. Skin friction measurements of systematically-varied roughness: Probing the role of roughness amplitude and skewness

    Science.gov (United States)

    Barros, Julio; Flack, Karen; Schultz, Michael

    2017-11-01

    Real-world engineering systems which feature either external or internal wall-bounded turbulent flow are routinely affected by surface roughness. This gives rise to performance degradation in the form of increased drag or head loss. However, at present there is no reliable means to predict these performance losses based upon the roughness topography alone. This work takes a systematic approach by generating random surface roughness in which the surface statistics are closely controlled. Skin friction and roughness function results will be presented for two groups of these rough surfaces. The first group is Gaussian (i.e. zero skewness) in which the root-mean-square roughness height (krms) is varied. The second group has a fixed krms, and the skewness is varied from approximately -1 to +1. The effect of the roughness amplitude and skewness on the skin friction will be discussed. Particular attention will be paid to the effect of these parameters on the roughness function in the transitionally-rough flow regime. For example, the role these parameters play in the monotonic or inflectional nature of the roughness function will be addressed. Future research into the details of the turbulence structure over these rough surfaces will also be outlined. Research funded by U.S. Office of Naval Research (ONR).

  5. Numerical Schemes for Rough Parabolic Equations

    Energy Technology Data Exchange (ETDEWEB)

    Deya, Aurelien, E-mail: deya@iecn.u-nancy.fr [Universite de Nancy 1, Institut Elie Cartan Nancy (France)

    2012-04-15

    This paper is devoted to the study of numerical approximation schemes for a class of parabolic equations on (0,1) perturbed by a non-linear rough signal. It is the continuation of Deya (Electron. J. Probab. 16:1489-1518, 2011) and Deya et al. (Probab. Theory Relat. Fields, to appear), where the existence and uniqueness of a solution has been established. The approach combines rough paths methods with standard considerations on discretizing stochastic PDEs. The results apply to a geometric 2-rough path, which covers the case of the multidimensional fractional Brownian motion with Hurst index H>1/3.

  6. Physical and sensory characteristics of pellets elaborated with different levels of corn grits and whey protein concentrate

    Directory of Open Access Journals (Sweden)

    Anderson Felicori Fernandes

    2016-04-01

    Full Text Available ABSTRACT Whey has proteins of high biological value, which has been used as an ingredient in the elaboration of yogurt, milk beverages and as protein concentrates. Food extrusion stands out as one of the most efficient cooking techniques, allowing a number of product types, from soluble flour to convenience products, such as snacks, which have high acceptability by the consumers. Products processed by extrusion, such as those expanded by frying (pellets, have high carbohydrate content, and its enrichment with protein can favor its nutritional aspect. This study aimed to use the whey protein concentrate (WPC in combination with corn grits in the preparation of pellets. Absolute density, density of expanded pellets, color, crispness index, and pellet sensory acceptance were determined. For the absolute density, contents from 5% to 17% produced denser non-expanded pellets. The higher the WPC content and the temperature of the extruder, the higher the density of the expanded pellets. The crispness index was not altered by the protein content and by the extruder temperature. In the sensory analysis, the preferred samples were the ones with lower WPC levels (5%. We concluded that higher WPC values in the pellets formulation increased their density, but did not alter color and texture, as well as small WPC levels did not affect the acceptance of snacks.

  7. A study of the sensitivity of an imaging telescope (GRITS) for high energy gamma-ray astronomy. Final report

    International Nuclear Information System (INIS)

    Yearian, M.R.

    1990-08-01

    When a gamma-ray telescope is placed in Earth orbit, it is bombarded by a flux of cosmic protons much greater than the flux of interesting gammas. These protons can interact in the telescope's thermal shielding to produce detectable gamma rays, most of which are vetoed. Since the proton flux is so high, the unvetoed gamma rays constitute a significant background relative to some weak sources. This background increases the observing time required to pinpoint some sources and entirely obscures other sources. Although recent telescopes have been designed to minimize this background, its strength and spectral characteristics were not previously calculated in detail. Monte Carlo calculations are presented which characterize the strength, spectrum and other features of the cosmic proton background using FLUKA, a hadronic cascade program. Several gamma-ray telescopes, including SAS-2, EGRET and the Gamma Ray Imaging Telescope System (GRITS), are analyzed, and their proton-induced backgrounds are characterized. In all cases, the backgrounds are either shown to be low relative to interesting signals or suggestions are made which would reduce the background sufficiently to leave the telescope unimpaired. In addition, several limiting cases are examined for comparison to previous estimates and calibration measurements

  8. Avaliação experimental de blocos prensados de solo-cimento com adição de grits

    Directory of Open Access Journals (Sweden)

    Márcia Lana Pinheiro

    Full Text Available A produção de resíduos pelas indústrias de papel e celulose vem crescendo continuamente, gerando custos com estocagem e aumentando os impactos ambientais. O presente trabalho teve como objetivo estudar a viabilidade de incorporação do resíduo grits, oriundo dessas indústrias, na fabricação de blocos prensados de encaixe de solo-cimento, como um novo material de construção. Foi verificada a maior quantidade de resíduo possível de ser utilizada, respeitando-se as exigências normativas. Para tanto, realizou-se caracterização física e mecânica de diversas proporções de solo-grits e foram fabricados blocos com as proporções investigadas. Após a cura, foram realizados, além de outros, os ensaios de resistência à compressão e absorção de água. Em relação à caracterização física, constatou-se que todos os teores de solo-grits atenderam às exigências normativas. Com relação à resistência à compressão e absorção de água, tem-se que as percentagens com plasticidade suficiente para fabricar os blocos também atenderam às exigências normativas. A porcentagem em massa de 37,5-62,5 de solo-grits pode ser definida como o teor que utiliza a maior quantidade de resíduo e tem plasticidade mínima necessária para a fabricação de blocos. Portanto, o uso do grits na produção de blocos de solo-cimento surge como uma tecnologia viável, além de minimizar a degradação ambiental.

  9. Spin Hall effect by surface roughness

    KAUST Repository

    Zhou, Lingjun; Grigoryan, Vahram L.; Maekawa, Sadamichi; Wang, Xuhui; Xiao, Jiang

    2015-01-01

    induced by surface roughness subscribes only to the side-jump contribution but not the skew scattering. The paradigm proposed in this paper provides the second, not if only, alternative to generate a sizable spin Hall effect.

  10. Roughness coefficients for stream channels in Arizona

    Science.gov (United States)

    Aldridge, B.N.; Garrett, J.M.

    1973-01-01

    When water flows in an open channel, energy is lost through friction along the banks and bed of the channel and through turbulence within the channel. The amount of energy lost is governed by channel roughness, which is expressed in terms of a roughness coefficient. An evaluation of the roughness coefficient is necessary in many hydraulic computations that involve flow in an open channel. Owing to the lack of satisfactory quantitative procedure, the ability of evaluate roughness coefficients can be developed only through experience; however, a basic knowledge of the methods used to assign the coefficients and the factors affecting them will be a great help. One of the most commonly used equations in open-channel hydraulics is that of Manning. The Manning equation is       1.486

  11. Investigation on Surface Roughness in Cylindrical Grinding

    Science.gov (United States)

    Rudrapati, Ramesh; Bandyopadhyay, Asish; Pal, Pradip Kumar

    2011-01-01

    Cylindrical grinding is a complex machining process. And surface roughness is often a key factor in any machining process while considering the machine tool or machining performance. Further, surface roughness is one of the measures of the technological quality of the product and is a factor that greatly influences cost and quality. The present work is related to some aspects of surface finish in the context of traverse-cut cylindrical grinding. The parameters considered have been: infeed, longitudinal feed and work speed. Taguchi quality design is used to design the experiments and to identify the significantly import parameter(s) affecting the surface roughness. By utilization of Response Surface Methodology (RSM), second order differential equation has been developed and attempts have also been made for optimization of the process in the context of surface roughness by using C- programming.

  12. Rough horizontal plates: heat transfer and hysteresis

    Energy Technology Data Exchange (ETDEWEB)

    Tisserand, J-C; Gasteuil, Y; Pabiou, H; Castaing, B; Chilla, F [Universite de Lyon, ENS Lyon, CNRS, 46 Allee d' ltalie, 69364 Lyon Cedex 7 (France); Creyssels, M [LMFA, CNRS, Ecole Centrale Lyon, 69134 Ecully Cedex (France); Gibert, M, E-mail: mathieu.creyssels@ec-lyon.fr [Also at MPI-DS (LFPN) Gottingen (Germany)

    2011-12-22

    To investigate the influence of a rough-wall boundary layer on turbulent heat transport, an experiment of high-Rayleigh convection in water is carried out in a Rayleigh-Benard cell with a rough lower plate and a smooth upper plate. A transition in the heat transport is observed when the thermal boundary layer thickness becomes comparable to or smaller than the roughness height. Besides, at larger Rayleigh numbers than the threshold value, heat transport is found to be increased up to 60%. This enhancement cannot be explained simply by an increase in the contact area of the rough surface since the contact area is increased only by a factor of 40%. Finally, a simple model is proposed to explain the enhanced heat transport.

  13. Surface excitation parameter for rough surfaces

    International Nuclear Information System (INIS)

    Da, Bo; Salma, Khanam; Ji, Hui; Mao, Shifeng; Zhang, Guanghui; Wang, Xiaoping; Ding, Zejun

    2015-01-01

    Graphical abstract: - Highlights: • Instead of providing a general mathematical model of roughness, we directly use a finite element triangle mesh method to build a fully 3D rough surface from the practical sample. • The surface plasmon excitation can be introduced to the realistic sample surface by dielectric response theory and finite element method. • We found that SEP calculated based on ideal plane surface model are still reliable for real sample surface with common roughness. - Abstract: In order to assess quantitatively the importance of surface excitation effect in surface electron spectroscopy measurement, surface excitation parameter (SEP) has been introduced to describe the surface excitation probability as an average number of surface excitations that electrons can undergo when they move through solid surface either in incoming or outgoing directions. Meanwhile, surface roughness is an inevitable issue in experiments particularly when the sample surface is cleaned with ion beam bombardment. Surface roughness alters not only the electron elastic peak intensity but also the surface excitation intensity. However, almost all of the popular theoretical models for determining SEP are based on ideal plane surface approximation. In order to figure out whether this approximation is efficient or not for SEP calculation and the scope of this assumption, we proposed a new way to determine the SEP for a rough surface by a Monte Carlo simulation of electron scattering process near to a realistic rough surface, which is modeled by a finite element analysis method according to AFM image. The elastic peak intensity is calculated for different electron incident and emission angles. Assuming surface excitations obey the Poisson distribution the SEPs corrected for surface roughness are then obtained by analyzing the elastic peak intensity for several materials and for different incident and emission angles. It is found that the surface roughness only plays an

  14. Small-Scale Surf Zone Geometric Roughness

    Science.gov (United States)

    2017-12-01

    using stereo imagery techniques. A waterproof two- camera system with self-logging and internal power was developed using commercial-off-the-shelf...estimates. 14. SUBJECT TERMS surface roughness, nearshore, aerodynamic roughness, surf zone, structure from motion, 3D imagery 15. NUMBER OF... power was developed using commercial-off-the- shelf components and commercial software for operations 1m above the sea surface within the surf zone

  15. How supercontinents and superoceans affect seafloor roughness.

    Science.gov (United States)

    Whittaker, Joanne M; Müller, R Dietmar; Roest, Walter R; Wessel, Paul; Smith, Walter H F

    2008-12-18

    Seafloor roughness varies considerably across the world's ocean basins and is fundamental to controlling the circulation and mixing of heat in the ocean and dissipating eddy kinetic energy. Models derived from analyses of active mid-ocean ridges suggest that ocean floor roughness depends on seafloor spreading rates, with rougher basement forming below a half-spreading rate threshold of 30-35 mm yr(-1) (refs 4, 5), as well as on the local interaction of mid-ocean ridges with mantle plumes or cold-spots. Here we present a global analysis of marine gravity-derived roughness, sediment thickness, seafloor isochrons and palaeo-spreading rates of Cretaceous to Cenozoic ridge flanks. Our analysis reveals that, after eliminating effects related to spreading rate and sediment thickness, residual roughness anomalies of 5-20 mGal remain over large swaths of ocean floor. We found that the roughness as a function of palaeo-spreading directions and isochron orientations indicates that most of the observed excess roughness is not related to spreading obliquity, as this effect is restricted to relatively rare occurrences of very high obliquity angles (>45 degrees ). Cretaceous Atlantic ocean floor, formed over mantle previously overlain by the Pangaea supercontinent, displays anomalously low roughness away from mantle plumes and is independent of spreading rates. We attribute this observation to a sub-Pangaean supercontinental mantle temperature anomaly leading to slightly thicker than normal Late Jurassic and Cretaceous Atlantic crust, reduced brittle fracturing and smoother basement relief. In contrast, ocean crust formed above Pacific superswells, probably reflecting metasomatized lithosphere underlain by mantle at only slightly elevated temperatures, is not associated with basement roughness anomalies. These results highlight a fundamental difference in the nature of large-scale mantle upwellings below supercontinents and superoceans, and their impact on oceanic crustal

  16. Role of surface roughness in superlubricity

    International Nuclear Information System (INIS)

    Tartaglino, U; Samoilov, V N; Persson, B N J

    2006-01-01

    We study the sliding of elastic solids in adhesive contact with flat and rough interfaces. We consider the dependence of the sliding friction on the elastic modulus of the solids. For elastically hard solids with planar surfaces with incommensurate surface structures we observe extremely low friction (superlubricity), which very abruptly increases as the elastic modulus decreases. We show that even a relatively small surface roughness may completely kill the superlubricity state

  17. Wall roughness induces asymptotic ultimate turbulence

    Science.gov (United States)

    Zhu, Xiaojue; Verschoof, Ruben A.; Bakhuis, Dennis; Huisman, Sander G.; Verzicco, Roberto; Sun, Chao; Lohse, Detlef

    2018-04-01

    Turbulence governs the transport of heat, mass and momentum on multiple scales. In real-world applications, wall-bounded turbulence typically involves surfaces that are rough; however, characterizing and understanding the effects of wall roughness on turbulence remains a challenge. Here, by combining extensive experiments and numerical simulations, we examine the paradigmatic Taylor-Couette system, which describes the closed flow between two independently rotating coaxial cylinders. We show how wall roughness greatly enhances the overall transport properties and the corresponding scaling exponents associated with wall-bounded turbulence. We reveal that if only one of the walls is rough, the bulk velocity is slaved to the rough side, due to the much stronger coupling to that wall by the detaching flow structures. If both walls are rough, the viscosity dependence is eliminated, giving rise to asymptotic ultimate turbulence—the upper limit of transport—the existence of which was predicted more than 50 years ago. In this limit, the scaling laws can be extrapolated to arbitrarily large Reynolds numbers.

  18. Dissolution of minerals with rough surfaces

    Science.gov (United States)

    de Assis, Thiago A.; Aarão Reis, Fábio D. A.

    2018-05-01

    We study dissolution of minerals with initial rough surfaces using kinetic Monte Carlo simulations and a scaling approach. We consider a simple cubic lattice structure, a thermally activated rate of detachment of a molecule (site), and rough surface configurations produced by fractional Brownian motion algorithm. First we revisit the problem of dissolution of initial flat surfaces, in which the dissolution rate rF reaches an approximately constant value at short times and is controlled by detachment of step edge sites. For initial rough surfaces, the dissolution rate r at short times is much larger than rF ; after dissolution of some hundreds of molecular layers, r decreases by some orders of magnitude across several time decades. Meanwhile, the surface evolves through configurations of decreasing energy, beginning with dissolution of isolated sites, then formation of terraces with disordered boundaries, their growth, and final smoothing. A crossover time to a smooth configuration is defined when r = 1.5rF ; the surface retreat at the crossover is approximately 3 times the initial roughness and is temperature-independent, while the crossover time is proportional to the initial roughness and is controlled by step-edge site detachment. The initial dissolution process is described by the so-called rough rates, which are measured for fixed ratios between the surface retreat and the initial roughness. The temperature dependence of the rough rates indicates control by kink site detachment; in general, it suggests that rough rates are controlled by the weakest microscopic bonds during the nucleation and formation of the lowest energy configurations of the crystalline surface. Our results are related to recent laboratory studies which show enhanced dissolution in polished calcite surfaces. In the application to calcite dissolution in alkaline environment, the minimal values of recently measured dissolution rate spectra give rF ∼10-9 mol/(m2 s), and the calculated rate

  19. Rough mill simulator version 3.0: an analysis tool for refining rough mill operations

    Science.gov (United States)

    Edward Thomas; Joel Weiss

    2006-01-01

    ROMI-3 is a rough mill computer simulation package designed to be used by both rip-first and chop-first rough mill operators and researchers. ROMI-3 allows users to model and examine the complex relationships among cutting bill, lumber grade mix, processing options, and their impact on rough mill yield and efficiency. Integrated into the ROMI-3 software is a new least-...

  20. Mitigating mask roughness via pupil filtering

    Science.gov (United States)

    Baylav, B.; Maloney, C.; Levinson, Z.; Bekaert, J.; Vaglio Pret, A.; Smith, B.

    2014-03-01

    The roughness present on the sidewalls of lithographically defined patterns imposes a very important challenge for advanced technology nodes. It can originate from the aerial image or the photoresist chemistry/processing [1]. The latter remains to be the dominant group in ArF and KrF lithography; however, the roughness originating from the mask transferred to the aerial image is gaining more attention [2-9], especially for the imaging conditions with large mask error enhancement factor (MEEF) values. The mask roughness contribution is usually in the low frequency range, which is particularly detrimental to the device performance by causing variations in electrical device parameters on the same chip [10-12]. This paper explains characteristic differences between pupil plane filtering in amplitude and in phase for the purpose of mitigating mask roughness transfer under interference-like lithography imaging conditions, where onedirectional periodic features are to be printed by partially coherent sources. A white noise edge roughness was used to perturbate the mask features for validating the mitigation.

  1. Development of nano-roughness calibration standards

    International Nuclear Information System (INIS)

    Baršić, Gorana; Mahović, Sanjin; Zorc, Hrvoje

    2012-01-01

    At the Laboratory for Precise Measurements of Length, currently the Croatian National Laboratory for Length, unique nano-roughness calibration standards were developed, which have been physically implemented in cooperation with the company MikroMasch Trading OU and the Ruđer Bošković Institute. In this paper, a new design for a calibration standard with two measuring surfaces is presented. One of the surfaces is for the reproduction of roughness parameters, while the other is for the traceability of length units below 50 nm. The nominal values of the groove depths on these measuring surfaces are the same. Thus, a link between the measuring surfaces has been ensured, which makes these standards unique. Furthermore, the calibration standards available on the market are generally designed specifically for individual groups of measuring instrumentation, such as interferometric microscopes, stylus instruments, scanning electron microscopes (SEM) or scanning probe microscopes. In this paper, a new design for nano-roughness standards has been proposed for use in the calibration of optical instruments, as well as for stylus instruments, SEM, atomic force microscopes and scanning tunneling microscopes. Therefore, the development of these new nano-roughness calibration standards greatly contributes to the reproducibility of the results of groove depth measurement as well as the 2D and 3D roughness parameters obtained by various measuring methods. (paper)

  2. A Rough Set Approach for Customer Segmentation

    Directory of Open Access Journals (Sweden)

    Prabha Dhandayudam

    2014-04-01

    Full Text Available Customer segmentation is a process that divides a business's total customers into groups according to their diversity of purchasing behavior and characteristics. The data mining clustering technique can be used to accomplish this customer segmentation. This technique clusters the customers in such a way that the customers in one group behave similarly when compared to the customers in other groups. The customer related data are categorical in nature. However, the clustering algorithms for categorical data are few and are unable to handle uncertainty. Rough set theory (RST is a mathematical approach that handles uncertainty and is capable of discovering knowledge from a database. This paper proposes a new clustering technique called MADO (Minimum Average Dissimilarity between Objects for categorical data based on elements of RST. The proposed algorithm is compared with other RST based clustering algorithms, such as MMR (Min-Min Roughness, MMeR (Min Mean Roughness, SDR (Standard Deviation Roughness, SSDR (Standard deviation of Standard Deviation Roughness, and MADE (Maximal Attributes DEpendency. The results show that for the real customer data considered, the MADO algorithm achieves clusters with higher cohesion, lower coupling, and less computational complexity when compared to the above mentioned algorithms. The proposed algorithm has also been tested on a synthetic data set to prove that it is also suitable for high dimensional data.

  3. Turbulent flow velocity distribution at rough walls

    International Nuclear Information System (INIS)

    Baumann, W.

    1978-08-01

    Following extensive measurements of the velocity profile in a plate channel with artificial roughness geometries specific investigations were carried out to verify the results obtained. The wall geometry used was formed by high transverse square ribs having a large pitch. The measuring position relative to the ribs was varied as a parameter thus providing a statement on the local influence of roughness ribs on the values measured. As a fundamental result it was found that the gradient of the logarithmic rough wall velocity profiles, which differs widely from the value 2.5, depends but slightly on the measuring position relative to the ribs. The gradients of the smooth wall velocity profiles deviate from 2.5 near the ribs, only. This fact can be explained by the smooth wall shear stress varying with the pitch of the ribs. (orig.) 891 GL [de

  4. Spin Hall effect by surface roughness

    KAUST Repository

    Zhou, Lingjun

    2015-01-08

    The spin Hall and its inverse effects, driven by the spin orbit interaction, provide an interconversion mechanism between spin and charge currents. Since the spin Hall effect generates and manipulates spin current electrically, to achieve a large effect is becoming an important topic in both academia and industries. So far, materials with heavy elements carrying a strong spin orbit interaction, provide the only option. We propose here a new mechanism, using the surface roughness in ultrathin films, to enhance the spin Hall effect without heavy elements. Our analysis based on Cu and Al thin films suggests that surface roughness is capable of driving a spin Hall angle that is comparable to that in bulk Au. We also demonstrate that the spin Hall effect induced by surface roughness subscribes only to the side-jump contribution but not the skew scattering. The paradigm proposed in this paper provides the second, not if only, alternative to generate a sizable spin Hall effect.

  5. Why do rough surfaces appear glossy?

    Science.gov (United States)

    Qi, Lin; Chantler, Mike J; Siebert, J Paul; Dong, Junyu

    2014-05-01

    The majority of work on the perception of gloss has been performed using smooth surfaces (e.g., spheres). Previous studies that have employed more complex surfaces reported that increasing mesoscale roughness increases perceived gloss [Psychol. Sci.19, 196 (2008), J. Vis.10(9), 13 (2010), Curr. Biol.22, 1909 (2012)]. We show that the use of realistic rendering conditions is important and that, in contrast to [Psychol. Sci.19, 196 (2008), J. Vis.10(9), 13 (2010)], after a certain point increasing roughness further actually reduces glossiness. We investigate five image statistics of estimated highlights and show that for our stimuli, one in particular, which we term "percentage of highlight area," is highly correlated with perceived gloss. We investigate a simple model that explains the unimodal, nonmonotonic relationship between mesoscale roughness and percentage highlight area.

  6. Fuzzy sets, rough sets, multisets and clustering

    CERN Document Server

    Dahlbom, Anders; Narukawa, Yasuo

    2017-01-01

    This book is dedicated to Prof. Sadaaki Miyamoto and presents cutting-edge papers in some of the areas in which he contributed. Bringing together contributions by leading researchers in the field, it concretely addresses clustering, multisets, rough sets and fuzzy sets, as well as their applications in areas such as decision-making. The book is divided in four parts, the first of which focuses on clustering and classification. The second part puts the spotlight on multisets, bags, fuzzy bags and other fuzzy extensions, while the third deals with rough sets. Rounding out the coverage, the last part explores fuzzy sets and decision-making.

  7. Diffuse neutron scattering signatures of rough films

    International Nuclear Information System (INIS)

    Pynn, R.; Lujan, M. Jr.

    1992-01-01

    Patterns of diffuse neutron scattering from thin films are calculated from a perturbation expansion based on the distorted-wave Born approximation. Diffuse fringes can be categorised into three types: those that occur at constant values of the incident or scattered neutron wavevectors, and those for which the neutron wavevector transfer perpendicular to the film is constant. The variation of intensity along these fringes can be used to deduce the spectrum of surface roughness for the film and the degree of correlation between the film's rough surfaces

  8. Wood-derived-biochar combined with compost or iron grit for in situ stabilization of Cd, Pb, and Zn in a contaminated soil.

    Science.gov (United States)

    Oustriere, Nadège; Marchand, Lilian; Rosette, Gabriel; Friesl-Hanl, Wolfgang; Mench, Michel

    2017-03-01

    In situ stabilization of Cd, Pb, and Zn in an Austrian agricultural soil contaminated by atmospheric depositions from a smelter plant was assessed with a pine bark chip-derived biochar, alone and in combination with either compost or iron grit. Biochar amendment was also trialed in an uncontaminated soil to detect any detrimental effect. The pot experiment consisted in ten soil treatments (% w/w): untreated contaminated soil (Unt); Unt soil amended with biochar alone (1%: B1; 2.5%: B2.5) and in combination: B1 and B2.5 + 5% compost (B1C and B2.5C), B1 and B2.5 + 1% iron grit (B1Z and B2.5Z); uncontaminated soil (Ctrl); Ctrl soil amended with 1 or 2.5% biochar (CtrlB1, CtrlB2.5). After a 3-month reaction period, the soil pore water (SPW) was sampled in potted soils and dwarf beans were grown for a 2-week period. The SPW Cd, Pb, and Zn concentrations decreased in all amended-contaminated soils. The biochar effects increased with its addition rate and its combination with either compost or iron grit. Shoot Cd and Zn removals by beans were reduced and shoot Cd, Pb, and Zn concentrations decreased to common values in all amended soils except the B1 soil. Decreases in the SPW Cd/Pb/Zn concentrations did not improve the root and shoot yields of plants as compared to the Ctrl soil.

  9. The Development of Expanded Snack Product Made from Pumpkin Flour-Corn Grits: Effect of Extrusion Conditions and Formulations on Physical Characteristics and Microstructure.

    Science.gov (United States)

    Nor, Norfezah Md; Carr, Alistair; Hardacre, Allan; Brennan, Charles S

    2013-05-14

    Pumpkin products confer natural sweetness, desirable flavours and β-carotene, a vitamin A precursor when added as ingredients to extruded snacks. Therefore, a potential use for dried pumpkin flour is as an ingredient in ready-to-eat (RTE) snack foods. Growth in this market has driven food manufacturers to produce a variety of new high value snack foods incorporating diverse ingredients to enhance the appearance and nutritional properties of these foods. Ready-to-eat snacks were made by extruding corn grits with 5%, 10%, 15% and 20% of pumpkin flour. Snacks made from 100% corn grits were used as control products for this work. The effect of formulation and screw speeds of 250 rpm and 350 rpm on torque and specific mechanical energy (SME, kWh/kg), physical characteristics (expansion ratio, bulk density, true density and hardness) and the microstructure of the snacks were studied. Increasing the screw speed resulted in a decrease of torque for all formulations. When pumpkin flour was added the specific mechanical energy (SME) decreased by approximately 45%. Increasing the percentage of pumpkin flour at the higher screw speed resulted in a harder texture for the extruded products. X-ray tomography of pumpkin flour-corn grit snacks showed that increased levels of pumpkin flour decreased both the bubble area and bubble size. However, no significant differences ( p > 0.05) in bubble wall thickness were measured. By understanding the conditions during extrusion, desirable nutritional characteristics can be incorporated while maximizing expansion to make a product with low bulk density, a fine bubble structure and acceptable organoleptic properties.

  10. The Development of Expanded Snack Product Made from Pumpkin Flour-Corn Grits: Effect of Extrusion Conditions and Formulations on Physical Characteristics and Microstructure

    Directory of Open Access Journals (Sweden)

    Norfezah Md Nor

    2013-05-01

    Full Text Available Pumpkin products confer natural sweetness, desirable flavours and β-carotene, a vitamin A precursor when added as ingredients to extruded snacks. Therefore, a potential use for dried pumpkin flour is as an ingredient in ready-to-eat (RTE snack foods. Growth in this market has driven food manufacturers to produce a variety of new high value snack foods incorporating diverse ingredients to enhance the appearance and nutritional properties of these foods. Ready-to-eat snacks were made by extruding corn grits with 5%, 10%, 15% and 20% of pumpkin flour. Snacks made from 100% corn grits were used as control products for this work. The effect of formulation and screw speeds of 250 rpm and 350 rpm on torque and specific mechanical energy (SME, kWh/kg, physical characteristics (expansion ratio, bulk density, true density and hardness and the microstructure of the snacks were studied. Increasing the screw speed resulted in a decrease of torque for all formulations. When pumpkin flour was added the specific mechanical energy (SME decreased by approximately 45%. Increasing the percentage of pumpkin flour at the higher screw speed resulted in a harder texture for the extruded products. X-ray tomography of pumpkin flour-corn grit snacks showed that increased levels of pumpkin flour decreased both the bubble area and bubble size. However, no significant differences (p > 0.05 in bubble wall thickness were measured. By understanding the conditions during extrusion, desirable nutritional characteristics can be incorporated while maximizing expansion to make a product with low bulk density, a fine bubble structure and acceptable organoleptic properties.

  11. Potential roughness near lithographically fabricated atom chips

    DEFF Research Database (Denmark)

    Krüger, Peter; Andersson, L. M.; Wildermuth, Stefan

    2007-01-01

    Potential roughness has been reported to severely impair experiments in magnetic microtraps. We show that these obstacles can be overcome as we measure disorder potentials that are reduced by two orders of magnitude near lithographically patterned high-quality gold layers on semiconductor atom chip...

  12. Rough flows and homogenization in stochastic turbulence

    OpenAIRE

    Bailleul, I.; Catellier, R.

    2016-01-01

    We provide in this work a tool-kit for the study of homogenisation of random ordinary differential equations, under the form of a friendly-user black box based on the tehcnology of rough flows. We illustrate the use of this setting on the example of stochastic turbulence.

  13. Reproducibility of surface roughness in reaming

    DEFF Research Database (Denmark)

    Müller, Pavel; De Chiffre, Leonardo

    An investigation on the reproducibility of surface roughness in reaming was performed to document the applicability of this approach for testing cutting fluids. Austenitic stainless steel was used as a workpiece material and HSS reamers as cutting tools. Reproducibility of the results was evaluat...

  14. Optical measurement of surface roughness in manufacturing

    Energy Technology Data Exchange (ETDEWEB)

    Brodmann, R.

    1984-11-01

    The measuring system described here is based on the light-scattering method, and was developed by Optische Werke G. Rodenstock, Munich. It is especially useful for rapid non-contact monitoring of surface roughness in production-related areas. This paper outlines the differences between this system and the common stylus instrument, including descriptions of some applications in industry.

  15. Microscopic Holography for flow over rough plate

    Science.gov (United States)

    Talapatra, Siddharth; Hong, Jiarong; Lu, Yuan; Katz, Joseph

    2008-11-01

    Our objective is to measure the near wall flow structures in a turbulent channel flow over a rough wall. In-line microscopic holographic PIV can resolve the 3-D flow field in a small sample volume, but recording holograms through a rough surface is a challenge. To solve this problem, we match the refractive indices of the fluid with that of the wall. Proof of concept tests involve an acrylic plate containing uniformly distributed, closely packed 0.45mm high pyramids with slope angle of 22^^o located within a concentrated sodium iodide solution. Holograms recorded by a 4864 x 3248 pixel digital camera at 10X magnification provide a field of view of 3.47mm x 2.32mm and pixel resolution of 0.714 μm. Due to index matching, reconstructed seed particles can be clearly seen over the entire volume, with only faint traces with the rough wall that can be removed. Planned experiments will be performed in a 20 x 5 cm rectangular channel with the top and bottom plates having the same roughness as the sample plate.

  16. Factors influencing surface roughness of polyimide film

    International Nuclear Information System (INIS)

    Yao Hong; Zhang Zhanwen; Huang Yong; Li Bo; Li Sai

    2011-01-01

    The polyimide (PI) films of pyromellitic dianhydride-oxydiamiline (PMDA-ODA) were fabricated using vapor deposition polymerization (VDP) method under high vacuum pressure of 10-4 Pa level. The influence of equipment, substrate temperature, the process of heating and deposition ratio of monomers on the surface roughness of the PI films was investigated. The surface topography of films was measured by interferometer microscopy and scanning electron microscopy(SEM), and the surface roughness was probed with atomic force microscopy(AFM). The results show that consecutive films can be formed when the distance from steering flow pipe to substrate is 74 cm. The surface roughnesses are 291.2 nm and 61.9 nm respectively for one-step heating process and multi-step heating process, and using fine mesh can effectively avoid the splash of materials. The surface roughness can be 3.3 nm when the deposition rate ratio of PMDA to ODA is 0.9:1, and keeping the temperature of substrate around 30 degree C is advantageous to form a film with planar micro-surface topography. (authors)

  17. Roughly isometric minimal immersions into Riemannian manifolds

    DEFF Research Database (Denmark)

    Markvorsen, Steen

    of the intrinsic combinatorial discrete Laplacian, and we will show that they share several analytic and geometric properties with their smooth (minimal submanifold) counterparts in $N$. The intrinsic properties thus obtained may hence serve as roughly invariant descriptors for the original metric space $X$....

  18. Three-tier rough superhydrophobic surfaces

    International Nuclear Information System (INIS)

    Cao, Yuanzhi; Yuan, Longyan; Hu, Bin; Zhou, Jun

    2015-01-01

    A three-tier rough superhydrophobic surface was fabricated by growing hydrophobic modified (fluorinated silane) zinc oxide (ZnO)/copper oxide (CuO) hetero-hierarchical structures on silicon (Si) micro-pillar arrays. Compared with the other three control samples with a less rough tier, the three-tier surface exhibits the best water repellency with the largest contact angle 161° and the lowest sliding angle 0.5°. It also shows a robust Cassie state which enables the water to flow with a speed over 2 m s"−"1. In addition, it could prevent itself from being wetted by the droplet with low surface tension (mixed water and ethanol 1:1 in volume) which reveals a flow speed of 0.6 m s"−"1 (dropped from the height of 2 cm). All these features prove that adding another rough tier on a two-tier rough surface could futher improve its water-repellent properties. (paper)

  19. Roughness-induced streaming in turbulent wave boundary layers

    DEFF Research Database (Denmark)

    Fuhrman, David R.; Sumer, B. Mutlu; Fredsøe, Jørgen

    2011-01-01

    -averaged streaming characteristics induced by bottom roughness variations are systematically assessed. The effects of variable roughness ratio, gradual roughness transitions, as well as changing flow orientation in plan are all considered. As part of the latter, roughness-induced secondary flows are predicted...

  20. Self-affine roughness influence on redox reaction charge admittance

    NARCIS (Netherlands)

    Palasantzas, G

    2005-01-01

    In this work we investigate the influence of self-affine electrode roughness on the admittance of redox reactions during facile charge transfer kinetics. The self-affine roughness is characterized by the rms roughness amplitude w, the correlation length xi and the roughness exponent H (0

  1. More on neutrosophic soft rough sets and its modification

    Directory of Open Access Journals (Sweden)

    Emad Marei

    2015-12-01

    Full Text Available This paper aims to introduce and discuss anew mathematical tool for dealing with uncertainties, which is a combination of neutrosophic sets, soft sets and rough sets, namely neutrosophic soft rough set model. Also, its modification is introduced. Some of their properties are studied and supported with proved propositions and many counter examples. Some of rough relations are redefined as a neutrosophic soft rough relations. Comparisons among traditional rough model, suggested neutrosophic soft rough model and its modification, by using their properties and accuracy measures are introduced. Finally, we illustrate that, classical rough set model can be viewed as a special case of suggested models in this paper.

  2. Turbulent boundary layer over roughness transition with variation in spanwise roughness length scale

    Science.gov (United States)

    Westerweel, Jerry; Tomas, Jasper; Eisma, Jerke; Pourquie, Mathieu; Elsinga, Gerrit; Jonker, Harm

    2016-11-01

    Both large-eddy simulations (LES) and water-tunnel experiments, using simultaneous stereoscopic PIV and LIF were done to investigate pollutant dispersion in a region where the surface changes from rural to urban roughness. This consists of rectangular obstacles where we vary the spanwise aspect ratio of the obstacles. A line source of passive tracer was placed upstream of the roughness transition. The objectives of the study are: (i) to determine the influence of the aspect ratio on the roughness-transition flow, and (ii) to determine the dominant mechanisms of pollutant removal from street canyons in the transition region. It is found that for a spanwise aspect ratio of 2 the drag induced by the roughness is largest of all considered cases, which is caused by a large-scale secondary flow. In the roughness transition the vertical advective pollutant flux is the main ventilation mechanism in the first three streets. Furthermore, by means of linear stochastic estimation the mean flow structure is identied that is responsible for exchange of the fluid between the roughness obstacles and the outer part of the boundary layer. Furthermore, it is found that the vertical length scale of this structure increases with increasing aspect ratio of the obstacles in the roughness region.

  3. Numerical Investigation of Effect of Surface Roughness in a Microchannel

    Energy Technology Data Exchange (ETDEWEB)

    Shin, Myung Seob; Byun, Sung Jun; Yoon, Joon Yong [Hanyang University, Seoul (Korea, Republic of)

    2010-05-15

    In this paper, lattice Boltzmann method(LBM) results for a laminar flow in a microchannel with rough surface are presented. The surface roughness is modeled as an array of rectangular modules placed on the top and bottom surface of a parallel-plate channel. The effects of relative surface roughness, roughness distribution, and roughness size are presented in terms of the Poiseuille number. The roughness distribution characterized by the ratio of the roughness height to the spacing between the modules has a negligible effect on the flow and friction factors. Finally, a significant increase in the Poiseuille number is observed when the surface roughness is considered, and the effects of roughness on the microflow field mainly depend on the surface roughness.

  4. Influência da imersão em água na resistência mecânica de misturas solo-grits compactadas e curadas com vistas a aplicações em estradas florestais Influence of water submersion on the mechanical strength of compacted and cured soil-grits mixtures for forest roads applications

    Directory of Open Access Journals (Sweden)

    Reginaldo Sérgio Pereira

    2007-01-01

    Full Text Available Avaliou-se o efeito da imersão em água dos corpos-de-prova sobre a resistência mecânica de misturas solo-grits. Trabalhou-se com dois solos da cidade de Viçosa, localizada na Zona da Mata Norte de Minas Gerais, Brasil, respectivamente de texturas predominantemente argilosa e arenosa e com o resíduo sólido industrial grits, um subproduto da indústria de celulose. Determinaram-se os parâmetros de resistência mecânica California Bearing Ratio (CBR e Resistência à Compressão Não-Confinada (RCNC de corpos-de-prova compactados nas energias de compactação referentes aos ensaios Proctor intermediário e Proctor modificado, com teores de grits na faixa de 4 a 28% e períodos de cura de 0, 7 e 28 dias. Com relação ao parâmetro CBR, os ensaios foram realizados segundo a metodologia tradicional (imersão em água dos corpos-de-prova por 96 horas e sem a imersão em água, visando determinar possíveis perdas na capacidade-suporte das misturas. No que tange ao parâmetro compressão não-confinada, os ensaios foram realizados em obediência à norma brasileira para misturas solo-cimento (imersão em água durante quatro horas antes da ruptura dos corpos-de-prova e sem a fase de imersão em água. Os resultados indicaram que a imersão em água dos corpos-de-prova influenciou significativamente a resistência mecânica das misturas solo-grits, que foram dependentes do tipo de ensaio empregado, tipo de solo, teor de grits, energia de compactação e período de cura.This paper address the influence of water submersion on mechanical strength parameters of soil-grits specimens. Two residual soils, predominantly clayey and sandy soils from the city of Viçosa, located in the State of Minas Gerais, "Zona da Mata Norte", Brazil, and waste from cellulose industry were used in the study. The laboratory testing program consisted of CBR (California Bearing Ratio and UCS (Unconfined Compression Strength of specimens prepared with waste contents

  5. Influence of biochars, compost and iron grit, alone and in combination, on copper solubility and phytotoxicity in a Cu-contaminated soil from a wood preservation site.

    Science.gov (United States)

    Oustriere, Nadège; Marchand, Lilian; Galland, William; Gabbon, Lunel; Lottier, Nathalie; Motelica, Mikael; Mench, Michel

    2016-10-01

    Two biochars, a green waste compost and iron grit were used, alone and in combination, as amendment to improve soil properties and in situ stabilize Cu in a contaminated soil (964mgCukg(-1)) from a wood preservation site. The pot experiment consisted in 9 soil treatments (% w/w): untreated Cu-contaminated soil (Unt); Unt soil amended respectively with compost (5%, C), iron grit (1%, Z), pine bark-derived biochar (1%, PB), poultry-manure-derived biochar (1%, AB), PB or AB+C (5%, PBC and ABC), and PB or AB+Z (1%, PBZ and ABZ). After a 3-month reaction period, the soil pore water (SPW) was sampled in potted soils and dwarf beans were grown for a 2-week period. In the SPW, all amendments decreased the Cu(2+) concentration, but total Cu concentration increased in all AB-amended soils due to high dissolved organic matter (DOM) concentration. No treatment improved root and shoot DW yields, which even decreased in the ABC and ABZ treatments. The PBZ treatment decreased total Cu concentration in the SPW while reducing the gap with common values for root and shoot yields of dwarf bean plants. A field trial is underway before any recommendation for the PB-based treatments. Copyright © 2016 Elsevier B.V. All rights reserved.

  6. The influence of surface roughness and high pressure torsion on the growth of anodic titania nanotubes on pure titanium

    Energy Technology Data Exchange (ETDEWEB)

    Hu, Nan; Gao, Nong, E-mail: N.Gao@soton.ac.uk; Starink, Marco J.

    2016-11-30

    Highlights: • HPT has substantially improved the UTS and Hv of pure Ti. • TNT layers was fabricated on UFG Ti made by HPT. • Influence of sample preparation on TNT layers was systematically studied. • Oxide dissolution was accelerated when TNTs formed on the HPT sample. - Abstract: Anodic titanium dioxide nanotube (TNT) arrays have wide applications in photocatalytic, catalysis, electronics, solar cells and biomedical implants. When TNT coatings are combined with severe plastic deformation (SPD), metal processing techniques which efficiently improve the strength of metals, a new generation of biomedical implant is made possible with both improved bulk and surface properties. This work investigated the effect of processing by high pressure torsion (HPT) and different mechanical preparations on the substrate and subsequently on the morphology of TNT layers. HPT processing was applied to refine the grain size of commercially pure titanium samples and substantially improved their strength and hardness. Subsequent anodization at 30 V in 0.25 wt.% NH{sub 4}F for 2 h to form TNT layers on sample surfaces prepared with different mechanical preparation methods was carried out. It appeared that the local roughness of the titanium surface on a microscopic level affected the TNT morphology more than the macroscopic surface roughness. For HPT-processed sample, the substrate has to be pre-treated by a mechanical preparation finer than 4000 grit for HPT to have a significant influence on TNTs. During the formation of TNT layers the oxide dissolution rate was increased for the ultrafine-grained microstructure formed due to HPT processing.

  7. Effect of chemical etching on the surface roughness of CdZnTe and CdMnTe gamma radiation detectors

    International Nuclear Information System (INIS)

    Hossain, A.; Babalola, S.; Bolotnikov, A.E.; Camarda, G.S.; Cui, Y.; Yang, G.; Guo, M.; Kochanowska, D.; Mycielski, A.; Burger, A.; James, R.B.

    2008-01-01

    Generally, mechanical polishing is performed to diminish the cutting damage followed by chemical etching to remove the remaining damage on crystal surfaces. In this paper, we detail the findings from our study of the effects of various chemical treatments on the roughness of crystal surfaces. We prepared several CdZnTe (CZT) and CdMnTe (CMT) crystals by mechanical polishing with 5 (micro)m and/or lower grits of Al 2 O 3 abrasive papers including final polishing with 0.05-(micro)m particle size alumina powder and then etched them for different periods with a 2%, 5% Bromine-Methanol (B-M) solution, and also with an E-solution (HNO 3 :H 2 O:Cr 2 O 7 ). The material removal rate (etching rate) from the crystals was found to be 10 (micro)m, 30 (micro)m, and 15 (micro)m per minute, respectively. The roughness of the resulting surfaces was determined by the Atomic Force Microscopy (AFM) to identify the most efficient surface processing method by combining mechanical and chemical polishing

  8. Anomalous roughness of turbulent interfaces with system size dependent local roughness exponent

    International Nuclear Information System (INIS)

    Balankin, Alexander S.; Matamoros, Daniel Morales

    2005-01-01

    In a system far from equilibrium the system size can play the role of control parameter that governs the spatiotemporal dynamics of the system. Accordingly, the kinetic roughness of interfaces in systems far from equilibrium may depend on the system size. To get an insight into this problem, we performed a detailed study of rough interfaces formed in paper combustion experiments. Using paper sheets of different width λ, we found that the turbulent flame fronts display anomalous multi-scaling characterized by non-universal global roughness exponent α and by the system size dependent spectrum of local roughness exponents, ζ q (λ)=ζ 1 (1)q -ω λ φ q =0.93q -0.15 . The structure factor of turbulent flame fronts also exhibits unconventional scaling dependence on λ. These results are expected to apply to a broad range of far from equilibrium systems when the kinetic energy fluctuations exceed a certain critical value.

  9. Generalized rough sets hybrid structure and applications

    CERN Document Server

    Mukherjee, Anjan

    2015-01-01

    The book introduces the concept of “generalized interval valued intuitionistic fuzzy soft sets”. It presents the basic properties of these sets and also, investigates an application of generalized interval valued intuitionistic fuzzy soft sets in decision making with respect to interval of degree of preference. The concept of “interval valued intuitionistic fuzzy soft rough sets” is discussed and interval valued intuitionistic fuzzy soft rough set based multi criteria group decision making scheme is presented, which refines the primary evaluation of the whole expert group and enables us to select the optimal object in a most reliable manner. The book also details concept of interval valued intuitionistic fuzzy sets of type 2. It presents the basic properties of these sets. The book also introduces the concept of “interval valued intuitionistic fuzzy soft topological space (IVIFS topological space)” together with intuitionistic fuzzy soft open sets (IVIFS open sets) and intuitionistic fuzzy soft cl...

  10. Single-layer model for surface roughness.

    Science.gov (United States)

    Carniglia, C K; Jensen, D G

    2002-06-01

    Random roughness of an optical surface reduces its specular reflectance and transmittance by the scattering of light. The reduction in reflectance can be modeled by a homogeneous layer on the surface if the refractive index of the layer is intermediate to the indices of the media on either side of the surface. Such a layer predicts an increase in the transmittance of the surface and therefore does not provide a valid model for the effects of scatter on the transmittance. Adding a small amount of absorption to the layer provides a model that predicts a reduction in both reflectance and transmittance. The absorbing layer model agrees with the predictions of a scalar scattering theory for a layer with a thickness that is twice the rms roughness of the surface. The extinction coefficient k for the layer is proportional to the thickness of the layer.

  11. Offshore Wind Power at Rough Sea

    DEFF Research Database (Denmark)

    Petersen, Kristian Rasmus; Madsen, Erik Skov; Bilberg, Arne

    2013-01-01

    This study compare the current operations and maintenance issues of one offshore wind park at very rough sea conditions and two onshore wind parks. Through a detailed data analysis and case studies this study identifies how improvements have been made in maintenance of large wind turbines. Howeve......, the study has also revealed the need for new maintenance models including a shift from breakdown and preventive maintenances and towards more predictive maintenance to reduce the cost of energy for offshore wind energy installations in the future.......This study compare the current operations and maintenance issues of one offshore wind park at very rough sea conditions and two onshore wind parks. Through a detailed data analysis and case studies this study identifies how improvements have been made in maintenance of large wind turbines. However...

  12. The contact sport of rough surfaces

    Science.gov (United States)

    Carpick, Robert W.

    2018-01-01

    Describing the way two surfaces touch and make contact may seem simple, but it is not. Fully describing the elastic deformation of ideally smooth contacting bodies, under even low applied pressure, involves second-order partial differential equations and fourth-rank elastic constant tensors. For more realistic rough surfaces, the problem becomes a multiscale exercise in surface-height statistics, even before including complex phenomena such as adhesion, plasticity, and fracture. A recent research competition, the “Contact Mechanics Challenge” (1), was designed to test various approximate methods for solving this problem. A hypothetical rough surface was generated, and the community was invited to model contact with this surface with competing theories for the calculation of properties, including contact area and pressure. A supercomputer-generated numerical solution was kept secret until competition entries were received. The comparison of results (2) provides insights into the relative merits of competing models and even experimental approaches to the problem.

  13. Prediction of Ductile Fracture Surface Roughness Scaling

    DEFF Research Database (Denmark)

    Needleman, Alan; Tvergaard, Viggo; Bouchaud, Elisabeth

    2012-01-01

    . Ductile crack growth in a thin strip under mode I, overall plane strain, small scale yielding conditions is analyzed. Although overall plane strain loading conditions are prescribed, full 3D analyses are carried out to permit modeling of the three dimensional material microstructure and of the resulting......Experimental observations have shown that the roughness of fracture surfaces exhibit certain characteristic scaling properties. Here, calculations are carried out to explore the extent to which a ductile damage/fracture constitutive relation can be used to model fracture surface roughness scaling...... three dimensional stress and deformation states that develop in the fracture process region. An elastic-viscoplastic constitutive relation for a progressively cavitating plastic solid is used to model the material. Two populations of second phase particles are represented: large inclusions with low...

  14. Estimation of gloss from rough surface parameters

    Science.gov (United States)

    Simonsen, Ingve; Larsen, Åge G.; Andreassen, Erik; Ommundsen, Espen; Nord-Varhaug, Katrin

    2005-12-01

    Gloss is a quantity used in the optical industry to quantify and categorize materials according to how well they scatter light specularly. With the aid of phase perturbation theory, we derive an approximate expression for this quantity for a one-dimensional randomly rough surface. It is demonstrated that gloss depends in an exponential way on two dimensionless quantities that are associated with the surface randomness: the root-mean-square roughness times the perpendicular momentum transfer for the specular direction, and a correlation function dependent factor times a lateral momentum variable associated with the collection angle. Rigorous Monte Carlo simulations are used to access the quality of this approximation, and good agreement is observed over large regions of parameter space.

  15. Sparseness and Roughness of Foreign Exchange Rates

    Science.gov (United States)

    Vandewalle, N.; Ausloos, M.

    An accurate multiaffine analysis of 23 foreign currency exchange rates has been performed. The roughness exponent H1 which characterizes the excursion of the exchange rate has been numerically measured. The degree of intermittency C1 has been also estimated. In the (H1,C1) phase diagram, the currency exchange rates are dispersed in a wide region around the Brownian motion value (H1=0.5,C1=0) and have a significantly intermittent component (C1≠0).

  16. Rough surface scattering simulations using graphics cards

    International Nuclear Information System (INIS)

    Klapetek, Petr; Valtr, Miroslav; Poruba, Ales; Necas, David; Ohlidal, Miloslav

    2010-01-01

    In this article we present results of rough surface scattering calculations using a graphical processing unit implementation of the Finite Difference in Time Domain algorithm. Numerical results are compared to real measurements and computational performance is compared to computer processor implementation of the same algorithm. As a basis for computations, atomic force microscope measurements of surface morphology are used. It is shown that the graphical processing unit capabilities can be used to speedup presented computationally demanding algorithms without loss of precision.

  17. Roughness Length Variability over Heterogeneous Surfaces

    Science.gov (United States)

    2010-03-01

    2004), the influence of variable roughness reaches its maximum at the height of local 0z and vanishes at the so- called blending height (Wieringa...the distribution of visibility restrictors such as low clouds, fog, haze, dust, and pollutants . An improved understanding of ABL structure...R. D., B. H. Lynn, A. Boone, W.-K. Tao, and J. Simpson, 2001: The influence of soil moisture, coastline curvature, and land-breeze circulations on

  18. Analysis of accuracy in photogrammetric roughness measurements

    Science.gov (United States)

    Olkowicz, Marcin; Dąbrowski, Marcin; Pluymakers, Anne

    2017-04-01

    Regarding permeability, one of the most important features of shale gas reservoirs is the effective aperture of cracks opened during hydraulic fracturing, both propped and unpropped. In a propped fracture, the aperture is controlled mostly by proppant size and its embedment, and fracture surface roughness only has a minor influence. In contrast, in an unpropped fracture aperture is controlled by the fracture roughness and the wall displacement. To measure fracture surface roughness, we have used the photogrammetric method since it is time- and cost-efficient. To estimate the accuracy of this method we compare the photogrammetric measurements with reference measurements taken with a White Light Interferometer (WLI). Our photogrammetric setup is based on high resolution 50 Mpx camera combined with a focus stacking technique. The first step for photogrammetric measurements is to determine the optimal camera positions and lighting. We compare multiple scans of one sample, taken with different settings of lighting and camera positions, with the reference WLI measurement. The second step is to perform measurements of all studied fractures with the parameters that produced the best results in the first step. To compare photogrammetric and WLI measurements we regrid both data sets onto a regular 10 μm grid and determined the best fit, followed by a calculation of the difference between the measurements. The first results of the comparison show that for 90 % of measured points the absolute vertical distance between WLI and photogrammetry is less than 10 μm, while the mean absolute vertical distance is 5 μm. This proves that our setup can be used for fracture roughness measurements in shales.

  19. The characteristic function of rough Heston models

    OpenAIRE

    Euch, Omar El; Rosenbaum, Mathieu

    2016-01-01

    It has been recently shown that rough volatility models, where the volatility is driven by a fractional Brownian motion with small Hurst parameter, provide very relevant dynamics in order to reproduce the behavior of both historical and implied volatilities. However, due to the non-Markovian nature of the fractional Brownian motion, they raise new issues when it comes to derivatives pricing. Using an original link between nearly unstable Hawkes processes and fractional volatility models, we c...

  20. Effect of Two Polishing Systems on Surface Roughness, Topography, and Flexural Strength of a Monolithic Lithium Disilicate Ceramic.

    Science.gov (United States)

    Mohammadibassir, Mahshid; Rezvani, Mohammad Bagher; Golzari, Hossein; Moravej Salehi, Elham; Fahimi, Mohammad Amin; Kharazi Fard, Mohammad Javad

    2017-03-08

    To evaluate the effect of overglazing and two polishing procedures on flexural strength and quality and quantity of surface roughness of a monolithic lithium disilicate ceramic computer-aided design (CAD) after grinding. This in vitro study was conducted on 52 partially crystalized bar-shaped specimens (16 × 4 × 1.6 mm) of monolithic lithium disilicate ceramic. The specimens were wet polished with 600-, 800-, and 1200-grit silicon carbide papers for 15 seconds using a grinding/polishing machine at a speed of 300 rpm. Then, the specimens were crystalized and glaze-fired in one step simultaneously and randomly divided into four groups of 13: (I) Glazing group (control); (II) Grinding-glazing group, subjected to grinding with red band finishing diamond bur (46 μm) followed by glazing; (III) Grinding-D+Z group, subjected to grinding and then polishing by coarse, medium, and fine diamond rubber points (D+Z); and (IV) Grinding-OptraFine group, subjected to grinding and then polishing with a two-step diamond rubber polishing system followed by a final polishing step with an OptraFine HP brush and diamond polishing paste. The surface roughness (Ra and Rz) values (μm) were measured by a profilometer, and the mean values were compared using one-way ANOVA and Tamhane's test (post hoc comparison). One specimen of each group was evaluated under a scanning electron microscope (SEM) for surface topography. The three-point flexural strength values of the bars were measured using a universal testing machine at a 0.5 mm/min crosshead speed and recorded. The data were analyzed using one-way ANOVA and Tamhane's test (α = 0.05). Statistically significant differences were noted among the experimental groups for Ra, Rz (p SEM analysis of polished surfaces revealed regular morphology with some striations. The OptraFine system created smoother and more uniform surfaces in terms of quantity (p < 0.03 for Ra, p < 0.01 for Rz) and quality of roughness compared to glazing. The flexural

  1. Radiative transfer model for contaminated rough slabs.

    Science.gov (United States)

    Andrieu, François; Douté, Sylvain; Schmidt, Frédéric; Schmitt, Bernard

    2015-11-01

    We present a semi-analytical model to simulate the bidirectional reflectance distribution function (BRDF) of a rough slab layer containing impurities. This model has been optimized for fast computation in order to analyze massive hyperspectral data by a Bayesian approach. We designed it for planetary surface ice studies but it could be used for other purposes. It estimates the bidirectional reflectance of a rough slab of material containing inclusions, overlaying an optically thick media (semi-infinite media or stratified media, for instance granular material). The inclusions are assumed to be close to spherical and constituted of any type of material other than the ice matrix. It can be any other type of ice, mineral, or even bubbles defined by their optical constants. We assume a low roughness and we consider the geometrical optics conditions. This model is thus applicable for inclusions larger than the considered wavelength. The scattering on the inclusions is assumed to be isotropic. This model has a fast computation implementation and thus is suitable for high-resolution hyperspectral data analysis.

  2. Multi-decadal Arctic sea ice roughness.

    Science.gov (United States)

    Tsamados, M.; Stroeve, J.; Kharbouche, S.; Muller, J. P., , Prof; Nolin, A. W.; Petty, A.; Haas, C.; Girard-Ardhuin, F.; Landy, J.

    2017-12-01

    The transformation of Arctic sea ice from mainly perennial, multi-year ice to a seasonal, first-year ice is believed to have been accompanied by a reduction of the roughness of the ice cover surface. This smoothening effect has been shown to (i) modify the momentum and heat transfer between the atmosphere and ocean, (ii) to alter the ice thickness distribution which in turn controls the snow and melt pond repartition over the ice cover, and (iii) to bias airborne and satellite remote sensing measurements that depend on the scattering and reflective characteristics over the sea ice surface topography. We will review existing and novel remote sensing methodologies proposed to estimate sea ice roughness, ranging from airborne LIDAR measurement (ie Operation IceBridge), to backscatter coefficients from scatterometers (ASCAT, QUICKSCAT), to multi angle maging spectroradiometer (MISR), and to laser (Icesat) and radar altimeters (Envisat, Cryosat, Altika, Sentinel-3). We will show that by comparing and cross-calibrating these different products we can offer a consistent multi-mission, multi-decadal view of the declining sea ice roughness. Implications for sea ice physics, climate and remote sensing will also be discussed.

  3. ROUGHNESS ANALYSIS OF VARIOUSLY POLISHED NIOBIUM SURFACES

    Energy Technology Data Exchange (ETDEWEB)

    Ribeill, G.; Reece, C.

    2008-01-01

    Niobium superconducting radio frequency (SRF) cavities have gained widespread use in accelerator systems. It has been shown that surface roughness is a determining factor in the cavities’ effi ciency and maximum accelerating potential achievable through this technology. Irregularities in the surface can lead to spot heating, undesirable local electrical fi eld enhancement and electron multipacting. Surface quality is typically ensured through the use of acid etching in a Buffered Chemical Polish (BCP) bath and electropolishing (EP). In this study, the effects of these techniques on surface morphology have been investigated in depth. The surface of niobium samples polished using different combinations of these techniques has been characterized through atomic force microscopy (AFM) and stylus profi lometry across a range of length scales. The surface morphology was analyzed using spectral techniques to determine roughness and characteristic dimensions. Experimentation has shown that this method is a valuable tool that provides quantitative information about surface roughness at different length scales. It has demonstrated that light BCP pretreatment and lower electrolyte temperature favors a smoother electropolish. These results will allow for the design of a superior polishing process for niobium SRF cavities and therefore increased accelerator operating effi ciency and power.

  4. Modeling superhydrophobic surfaces comprised of random roughness

    Science.gov (United States)

    Samaha, M. A.; Tafreshi, H. Vahedi; Gad-El-Hak, M.

    2011-11-01

    We model the performance of superhydrophobic surfaces comprised of randomly distributed roughness that resembles natural surfaces, or those produced via random deposition of hydrophobic particles. Such a fabrication method is far less expensive than ordered-microstructured fabrication. The present numerical simulations are aimed at improving our understanding of the drag reduction effect and the stability of the air-water interface in terms of the microstructure parameters. For comparison and validation, we have also simulated the flow over superhydrophobic surfaces made up of aligned or staggered microposts for channel flows as well as streamwise or spanwise ridge configurations for pipe flows. The present results are compared with other theoretical and experimental studies. The numerical simulations indicate that the random distribution of surface roughness has a favorable effect on drag reduction, as long as the gas fraction is kept the same. The stability of the meniscus, however, is strongly influenced by the average spacing between the roughness peaks, which needs to be carefully examined before a surface can be recommended for fabrication. Financial support from DARPA, contract number W91CRB-10-1-0003, is acknowledged.

  5. Rough – Granular Computing knowledge discovery models

    Directory of Open Access Journals (Sweden)

    Mohammed M. Eissa

    2016-11-01

    Full Text Available Medical domain has become one of the most important areas of research in order to richness huge amounts of medical information about the symptoms of diseases and how to distinguish between them to diagnose it correctly. Knowledge discovery models play vital role in refinement and mining of medical indicators to help medical experts to settle treatment decisions. This paper introduces four hybrid Rough – Granular Computing knowledge discovery models based on Rough Sets Theory, Artificial Neural Networks, Genetic Algorithm and Rough Mereology Theory. A comparative analysis of various knowledge discovery models that use different knowledge discovery techniques for data pre-processing, reduction, and data mining supports medical experts to extract the main medical indicators, to reduce the misdiagnosis rates and to improve decision-making for medical diagnosis and treatment. The proposed models utilized two medical datasets: Coronary Heart Disease dataset and Hepatitis C Virus dataset. The main purpose of this paper was to explore and evaluate the proposed models based on Granular Computing methodology for knowledge extraction according to different evaluation criteria for classification of medical datasets. Another purpose is to make enhancement in the frame of KDD processes for supervised learning using Granular Computing methodology.

  6. The surface roughness and planetary boundary layer

    Science.gov (United States)

    Telford, James W.

    1980-03-01

    Applications of the entrainment process to layers at the boundary, which meet the self similarity requirements of the logarithmic profile, have been studied. By accepting that turbulence has dominating scales related in scale length to the height above the surface, a layer structure is postulated wherein exchange is rapid enough to keep the layers internally uniform. The diffusion rate is then controlled by entrainment between layers. It has been shown that theoretical relationships derived on the basis of using a single layer of this type give quantitatively correct factors relating the turbulence, wind and shear stress for very rough surface conditions. For less rough surfaces, the surface boundary layer can be divided into several layers interacting by entrainment across each interface. This analysis leads to the following quantitatively correct formula compared to published measurements. 1 24_2004_Article_BF00877766_TeX2GIFE1.gif {σ _w }/{u^* } = ( {2/{9Aa}} )^{{1/4}} ( {1 - 3^{{1/2}{ a/k{d_n }/z{σ _w }/{u^* }z/L} )^{{1/4}} = 1.28(1 - 0.945({{σ _w }/{u^* }}}) {{z/L}})^{{1/4 where u^* = ( {{tau/ρ}}^{{1/2}}, σ w is the standard deviation of the vertical velocity, z is the height and L is the Obukhov scale lenght. The constants a, A, k and d n are the entrainment constant, the turbulence decay constant, Von Karman's constant, and the layer depth derived from the theory. Of these, a and A, are universal constants and not empirically determined for the boundary layer. Thus the turbulence needed for the plume model of convection, which resides above these layers and reaches to the inversion, is determined by the shear stress and the heat flux in the surface layers. This model applies to convection in cool air over a warm sea. The whole field is now determined except for the temperature of the air relative to the water, and the wind, which need a further parameter describing sea surface roughness. As a first stop to describing a surface where roughness elements

  7. Inner-outer interactions in a rough wall turbulent boundary layer over hemispherical roughness using PIV

    Science.gov (United States)

    Pathikonda, Gokul; Clark, Caitlyn; Christensen, Kenneth T.

    2017-11-01

    Inner-outer interactions over rough-wall boundary layer were investigated using high frame-rate, PIV measurements in a Refractive index-matched (RIM) facility. Flows over canonical smooth-wall and hexagonally-packed hemispherical roughness under transitionally rough flow conditions (and with Reτ 1500) were measured using a dual camera PIV system with different fields of view (FOVs) and operating simultaneously. The large FOV measures the large scales and boundary layer parameters, while the small FOV measures the small scales very close to the wall with high spatial ( 7y*) and temporal ( 2.5t*) resolutions. Conditional metrics were formulated to investigate these scale interactions in a spatio-temporal sense using the PIV data. It was found that the observations complement the interaction structure made via hotwire experiments and DNS in previous studies over both smooth and rough-wall flows, with a strong correlation between the large scales and small scale energies indicative of the amplitude modulation interactions. Additionally, frequency and scale modulations were also investigated with limited success. These experiments highlight the similarities and differences in these interactions between the smooth- and rough-wall flows.

  8. Dewetting of thin polymer film on rough substrate: II. Experiment

    International Nuclear Information System (INIS)

    Volodin, Pylyp; Kondyurin, Alexey

    2008-01-01

    The theory of the dewetting process developed for a model of substrate-film interaction forces was examined by an experimental investigation of the dewetting process of thin polystyrene (PS) films on chemically etched silicon substrates. In the dependence on PS films thickness and silicon roughness, various situations of dewetting were observed as follows: (i) if the wavelength of the substrate roughness is much larger than the critical spinodal wavelength of a film, then spinodal dewetting of the film is observed; (ii) if the wavelength of the substrate roughness is smaller than the critical wavelength of the film and the substrate roughness is larger in comparison with film thickness, then the dewetting due to substrate roughness is observed and the dewetted film patterns repeat the rough substrate structure; (iii) if the wavelength of the substrate roughness is smaller than the critical wavelength of the film and the substrate roughness is small in comparison with the film thickness, then spinodal dewetting proceeds

  9. Sub-Patch Roughness in Earthquake Rupture Investigations

    KAUST Repository

    Zielke, Olaf; Mai, Paul Martin

    2016-01-01

    Fault geometric complexities exhibit fractal characteristics over a wide range of spatial scales (<µm to >km) and strongly affect the rupture process at corresponding scales. Numerical rupture simulations provide a framework to quantitatively investigate the relationship between a fault's roughness and its seismic characteristics. Fault discretization however introduces an artificial lower limit to roughness. Individual fault patches are planar and sub-patch roughnessroughness at spatial scales below fault-patch size– is not incorporated. Does negligence of sub-patch roughness measurably affect the outcome of earthquake rupture simulations? We approach this question with a numerical parameter space investigation and demonstrate that sub-patch roughness significantly modifies the slip-strain relationship –a fundamental aspect of dislocation theory. Faults with sub-patch roughness induce less strain than their planar-fault equivalents at distances beyond the length of a slipping fault. We further provide regression functions that characterize the stochastic effect sub-patch roughness.

  10. Roughness characterization of the galling of metals

    Science.gov (United States)

    Hubert, C.; Marteau, J.; Deltombe, R.; Chen, Y. M.; Bigerelle, M.

    2014-09-01

    Several kinds of tests exist to characterize the galling of metals, such as that specified in ASTM Standard G98. While the testing procedure is accurate and robust, the analysis of the specimen's surfaces (area=1.2 cm) for the determination of the critical pressure of galling remains subject to operator judgment. Based on the surface's topography analyses, we propose a methodology to express the probability of galling according to the macroscopic pressure load. After performing galling tests on 304L stainless steel, a two-step segmentation of the S q parameter (root mean square of surface amplitude) computed from local roughness maps (100 μ m× 100 μ m) enables us to distinguish two tribological processes. The first step represents the abrasive wear (erosion) and the second one the adhesive wear (galling). The total areas of both regions are highly relevant to quantify galling and erosion processes. Then, a one-parameter phenomenological model is proposed to objectively determine the evolution of non-galled relative area A e versus the pressure load P, with high accuracy ({{A}e}=100/(1+a{{P}2}) with a={{0.54}+/- 0.07}× {{10}-3} M P{{a}-2} and with {{R}2}=0.98). From this model, the critical pressure of galling is found to be equal to 43MPa. The {{S}5 V} roughness parameter (the five deepest valleys in the galled region's surface) is the most relevant roughness parameter for the quantification of damages in the ‘galling region’. The significant valleys’ depths increase from 10 μm-250 μm when the pressure increases from 11-350 MPa, according to a power law ({{S}5 V}=4.2{{P}0.75}, with {{R}2}=0.93).

  11. Robust surface roughness indices and morphological interpretation

    Science.gov (United States)

    Trevisani, Sebastiano; Rocca, Michele

    2016-04-01

    Geostatistical-based image/surface texture indices based on variogram (Atkison and Lewis, 2000; Herzfeld and Higginson, 1996; Trevisani et al., 2012) and on its robust variant MAD (median absolute differences, Trevisani and Rocca, 2015) offer powerful tools for the analysis and interpretation of surface morphology (potentially not limited to solid earth). In particular, the proposed robust index (Trevisani and Rocca, 2015) with its implementation based on local kernels permits the derivation of a wide set of robust and customizable geomorphometric indices capable to outline specific aspects of surface texture. The stability of MAD in presence of signal noise and abrupt changes in spatial variability is well suited for the analysis of high-resolution digital terrain models. Moreover, the implementation of MAD by means of a pixel-centered perspective based on local kernels, with some analogies to the local binary pattern approach (Lucieer and Stein, 2005; Ojala et al., 2002), permits to create custom roughness indices capable to outline different aspects of surface roughness (Grohmann et al., 2011; Smith, 2015). In the proposed poster, some potentialities of the new indices in the context of geomorphometry and landscape analysis will be presented. At same time, challenges and future developments related to the proposed indices will be outlined. Atkinson, P.M., Lewis, P., 2000. Geostatistical classification for remote sensing: an introduction. Computers & Geosciences 26, 361-371. Grohmann, C.H., Smith, M.J., Riccomini, C., 2011. Multiscale Analysis of Topographic Surface Roughness in the Midland Valley, Scotland. IEEE Transactions on Geoscience and Remote Sensing 49, 1220-1213. Herzfeld, U.C., Higginson, C.A., 1996. Automated geostatistical seafloor classification - Principles, parameters, feature vectors, and discrimination criteria. Computers and Geosciences, 22 (1), pp. 35-52. Lucieer, A., Stein, A., 2005. Texture-based landform segmentation of LiDAR imagery

  12. Traceability of optical roughness measurements on polymers

    DEFF Research Database (Denmark)

    De Chiffre, Leonardo; Gasparin, Stefania; Carli, Lorenzo

    2008-01-01

    -focus instrument, and a confocal microscope. Using stylus measurements as reference, parameter settings on the optical instruments were optimised and residual noise reduced by low pass filtering. Traceability of optical measurements could be established with expanded measuring uncertainties (k=2) of 4......An experimental investigation on surface roughness measurements on plastics was carried out with the objective of developing a methodology to achieve traceability of optical instruments. A ground steel surface and its replicas were measured using a stylus instrument, an optical auto......% for the auto-focus instrument and 10% for confocal microscope....

  13. Wave scattering from statistically rough surfaces

    CERN Document Server

    Bass, F G; ter Haar, D

    2013-01-01

    Wave Scattering from Statistically Rough Surfaces discusses the complications in radio physics and hydro-acoustics in relation to wave transmission under settings seen in nature. Some of the topics that are covered include radar and sonar, the effect of variations in topographic relief or ocean waves on the transmission of radio and sound waves, the reproduction of radio waves from the lower layers of the ionosphere, and the oscillations of signals within the earth-ionosphere waveguide. The book begins with some fundamental idea of wave transmission theory and the theory of random processes a

  14. Surface correlations of hydrodynamic drag for transitionally rough engineering surfaces

    Science.gov (United States)

    Thakkar, Manan; Busse, Angela; Sandham, Neil

    2017-02-01

    Rough surfaces are usually characterised by a single equivalent sand-grain roughness height scale that typically needs to be determined from laboratory experiments. Recently, this method has been complemented by a direct numerical simulation approach, whereby representative surfaces can be scanned and the roughness effects computed over a range of Reynolds number. This development raises the prospect over the coming years of having enough data for different types of rough surfaces to be able to relate surface characteristics to roughness effects, such as the roughness function that quantifies the downward displacement of the logarithmic law of the wall. In the present contribution, we use simulation data for 17 irregular surfaces at the same friction Reynolds number, for which they are in the transitionally rough regime. All surfaces are scaled to the same physical roughness height. Mean streamwise velocity profiles show a wide range of roughness function values, while the velocity defect profiles show a good collapse. Profile peaks of the turbulent kinetic energy also vary depending on the surface. We then consider which surface properties are important and how new properties can be incorporated into an empirical model, the accuracy of which can then be tested. Optimised models with several roughness parameters are systematically developed for the roughness function and profile peak turbulent kinetic energy. In determining the roughness function, besides the known parameters of solidity (or frontal area ratio) and skewness, it is shown that the streamwise correlation length and the root-mean-square roughness height are also significant. The peak turbulent kinetic energy is determined by the skewness and root-mean-square roughness height, along with the mean forward-facing surface angle and spanwise effective slope. The results suggest feasibility of relating rough-wall flow properties (throughout the range from hydrodynamically smooth to fully rough) to surface

  15. Urban roughness mapping validation techniques and some first results

    NARCIS (Netherlands)

    Bottema, M; Mestayer, PG

    1998-01-01

    Because of measuring problems related to evaluation of urban roughness parameters, a new approach using a roughness mapping tool has been tested: evaluation of roughness length z(o) and zero displacement z(d) from cadastral databases. Special attention needs to be given to the validation of the

  16. Procedure and applications of combined wheel/rail roughness measurement

    NARCIS (Netherlands)

    Dittrich, M.G.

    2009-01-01

    Wheel-rail roughness is known to be the main excitation source of railway rolling noise. Besides the already standardised method for direct roughness measurement, it is also possible to measure combined wheel-rail roughness from vertical railhead vibration during a train pass-by. This is a different

  17. Rough sets applied in sublattices and ideals of lattices

    Directory of Open Access Journals (Sweden)

    R. Ameri

    2015-12-01

    Full Text Available The purpose of this paper is the study of rough hyperlattice. In this regards we introduce rough sublattice and rough ideals of lattices. We will proceed by obtaining lower and upper approximations in these lattices.

  18. Use of roughness maps in visualisation of surfaces

    DEFF Research Database (Denmark)

    Seitavuopio, Paulus; Rantanen, Jukka; Yliruusi, Jouko

    2005-01-01

    monohydrate, theophylline anhydrate, sodium chloride and potassium chloride. The roughness determinations were made by a laser profilometer. The new matrix method gives detailed roughness maps, which are able to show local variations in surface roughness values and provide an illustrative picture...

  19. ROMI 4.0: Updated Rough Mill Simulator

    Science.gov (United States)

    Timo Grueneberg; R. Edward Thomas; Urs Buehlmann

    2012-01-01

    In the secondary hardwood industry, rough mills convert hardwood lumber into dimension parts for furniture, cabinets, and other wood products. ROMI 4.0, the US Department of Agriculture Forest Service's ROugh-MIll simulator, is a software package designed to simulate the cut-up of hardwood lumber in rough mills in such a way that a maximum possible component yield...

  20. Rough sets selected methods and applications in management and engineering

    CERN Document Server

    Peters, Georg; Ślęzak, Dominik; Yao, Yiyu

    2012-01-01

    Introduced in the early 1980s, Rough Set Theory has become an important part of soft computing in the last 25 years. This book provides a practical, context-based analysis of rough set theory, with each chapter exploring a real-world application of Rough Sets.

  1. 7 CFR 868.201 - Definition of rough rice.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 7 2010-01-01 2010-01-01 false Definition of rough rice. 868.201 Section 868.201... FOR CERTAIN AGRICULTURAL COMMODITIES United States Standards for Rough Rice Terms Defined § 868.201 Definition of rough rice. Rice (Oryza sativa L.) which consists of 50 percent or more of paddy kernels (see...

  2. Characterization of steel grit recovered from ornamental rocks waste by magnetic separation; Caracterizacao da granalha de aco recuperada do residuo de rochas ornamentais por separacao magnetica

    Energy Technology Data Exchange (ETDEWEB)

    Junca, E.; Telles, V.B.; Rodrigues, G.F.; Oliveira, J.R. de; Tenorio, J.A.S., E-mail: eduardojunca@gmail.co [Universidade de Sao Paulo (USP), SP (Brazil). Dept. de Engenharia Metalurgica e de Materiais; Instituto Federal de Ciencia e Tecnologia do Espirito Santo (IFES), Vitoria, ES (Brazil)

    2010-07-01

    The aim of this work is characterization of steel grit recovered from ornamental rock waste by magnetic separation. The magnetic separation was realized in three steps: first, using a high intensity wet magnetic separator, which used only the remaining magnetic field of equipment. In the second step, the magnetic material obtained in the first phase was subjected to a new manual magnetic separation using rare earth magnets. In a third step, magnetic material obtained with rare earth magnets was subjected to manual magnetic separation using ferrite magnets. After the magnetic separation, the material was sent to characterization which was obtained by chemical analysis, scanning electron microscopy, X-ray diffraction and size analysis. The size analysis showed that the concentrate range from 0,5 to 563,67 {mu}m with 4 wt.% over 100 {mu}m and content metallic iron of 93 wt%. (author)

  3. Rough viscoelastic sliding contact: Theory and experiments

    Science.gov (United States)

    Carbone, G.; Putignano, C.

    2014-03-01

    In this paper, we show how the numerical theory introduced by the authors [Carbone and Putignano, J. Mech. Phys. Solids 61, 1822 (2013), 10.1016/j.jmps.2013.03.005] can be effectively employed to study the contact between viscoelastic rough solids. The huge numerical complexity is successfully faced up by employing the adaptive nonuniform mesh developed by the authors in Putignano et al. [J. Mech. Phys. Solids 60, 973 (2012), 10.1016/j.jmps.2012.01.006]. Results mark the importance of accounting for viscoelastic effects to correctly simulate the sliding rough contact. In detail, attention is, first, paid to evaluate the viscoelastic dissipation, i.e., the viscoelastic friction. Fixed the sliding speed and the normal load, friction is completely determined. Furthermore, since the methodology employed in the work allows to study contact between real materials, a comparison between experimental outcomes and numerical prediction in terms of viscoelastic friction is shown. The good agreement seems to validate—at least partially—the presented methodology. Finally, it is shown that viscoelasticity entails not only the dissipative effects previously outlined, but is also strictly related to the anisotropy of the contact solution. Indeed, a marked anisotropy is present in the contact region, which results stretched in the direction perpendicular to the sliding speed. In the paper, the anisotropy of the deformed surface and of the contact area is investigated and quantified.

  4. Roughness as classicality indicator of a quantum state

    Science.gov (United States)

    Lemos, Humberto C. F.; Almeida, Alexandre C. L.; Amaral, Barbara; Oliveira, Adélcio C.

    2018-03-01

    We define a new quantifier of classicality for a quantum state, the Roughness, which is given by the L2 (R2) distance between Wigner and Husimi functions. We show that the Roughness is bounded and therefore it is a useful tool for comparison between different quantum states for single bosonic systems. The state classification via the Roughness is not binary, but rather it is continuous in the interval [ 0 , 1 ], being the state more classic as the Roughness approaches to zero, and more quantum when it is closer to the unity. The Roughness is maximum for Fock states when its number of photons is arbitrarily large, and also for squeezed states at the maximum compression limit. On the other hand, the Roughness approaches its minimum value for thermal states at infinite temperature and, more generally, for infinite entropy states. The Roughness of a coherent state is slightly below one half, so we may say that it is more a classical state than a quantum one. Another important result is that the Roughness performs well for discriminating both pure and mixed states. Since the Roughness measures the inherent quantumness of a state, we propose another function, the Dynamic Distance Measure (DDM), which is suitable for measure how much quantum is a dynamics. Using DDM, we studied the quartic oscillator, and we observed that there is a certain complementarity between dynamics and state, i.e. when dynamics becomes more quantum, the Roughness of the state decreases, while the Roughness grows as the dynamics becomes less quantum.

  5. Effect of Blade Roughness on Transition and Wind Turbine Performance.

    Energy Technology Data Exchange (ETDEWEB)

    Ehrmann, Robert S. [Texas A & M Univ., College Station, TX (United States); White, E. B. [Texas A & M Univ., College Station, TX (United States)

    2015-09-01

    The real-world effect of accumulated surface roughness on wind-turbine power production is not well understood. To isolate specific blade roughness features and test their effect, field measurements of turbine-blade roughness were made and simulated on a NACA 633-418 airfoil in a wind tunnel. Insect roughness, paint chips, and erosion were characterized then manufactured. In the tests, these roughness configurations were recreated as distributed roughness, a forward-facing step, and an eroded leading edge. Distributed roughness was tested in three heights and five densities. Chord Reynolds number was varied between 0:8 to 4:8 × 106. Measurements included lift, drag, pitching moment, and boundary-layer transition location. Results indicate minimal effect from paint-chip roughness. As distributed roughness height and density increase, the lift-curve slope, maximum lift, and lift-to-drag ratio decrease. As Reynolds number increases, natural transition is replaced by bypass transition. The critical roughness Reynolds number varies between 178 to 318, within the historical range. At a chord Reynolds number of 3:2 × 106, the maximum lift-to-drag ratio decreases 40% for 140 μm roughness, corresponding to a 2.3% loss in annual energy production. Simulated performance loss compares well to measured performance loss of an in-service wind turbine.

  6. Skin friction measurements of mathematically generated roughness in the transitionally- to fully-rough regimes

    Science.gov (United States)

    Barros, Julio; Schultz, Michael; Flack, Karen

    2016-11-01

    Engineering systems are affected by surface roughness which cause an increase in drag leading to significant performance penalties. One important question is how to predict frictional drag purely based upon surface topography. Although significant progress has been made in recent years, this has proven to be challenging. The present work takes a systematic approach by generating surface roughness in which surfaces parameters, such as rms , skewness, can be controlled. Surfaces were produced using the random Fourier modes method with enforced power-law spectral slopes. The surfaces were manufactured using high resolution 3D-printing. In this study three surfaces with constant amplitude and varying slope, P, were investigated (P = - 0 . 5 , - 1 . 0 , - 1 . 5). Skin-friction measurements were conducted in a high Reynolds number turbulent channel flow facility, covering a wide range of Reynolds numbers, from hydraulic-smooth to fully-rough regimes. Results show that some long wavelength roughness scales do not contribute significantly to the frictional drag, thus highlighting the need for filtering in the calculation of surface statistics. Upon high-pass filtering, it was found that krms is highly correlated with the measured ks.

  7. Influence of surface roughness of a desert

    Science.gov (United States)

    Sud, Y. C.; Smith, W. E.

    1984-01-01

    A numerical simulation study, using the current GLAS climate GCM, was carried out to examine the influence of low bulk aerodynamic drag parameter in the deserts. The results illustrate the importance of yet another feedback effect of a desert on itself, that is produced by the reduction in surface roughness height of land once the vegetation dies and desert forms. Apart from affecting the moisture convergence, low bulk transport coefficients of a desert lead to enhanced longwave cooling and sinking which together reduce precipitation by Charney's (1975) mechanism. Thus, this effect, together with albedo and soil moisture influence, perpetuate a desert condition through its geophysical feedback effect. The study further suggests that man made deserts is a viable hypothesis.

  8. Urban Aerodynamic Roughness Length Mapping Using Multitemporal SAR Data

    Directory of Open Access Journals (Sweden)

    Fengli Zhang

    2017-01-01

    Full Text Available Aerodynamic roughness is very important to urban meteorological and climate studies. Radar remote sensing is considered to be an effective means for aerodynamic roughness retrieval because radar backscattering is sensitive to the surface roughness and geometric structure of a given target. In this paper, a methodology for aerodynamic roughness length estimation using SAR data in urban areas is introduced. The scale and orientation characteristics of backscattering of various targets in urban areas were firstly extracted and analyzed, which showed great potential of SAR data for urban roughness elements characterization. Then the ground truth aerodynamic roughness was calculated from wind gradient data acquired by the meteorological tower using fitting and iterative method. And then the optimal dimension of the upwind sector for the aerodynamic roughness calculation was determined through a correlation analysis between backscattering extracted from SAR data at various upwind sector areas and the aerodynamic roughness calculated from the meteorological tower data. Finally a quantitative relationship was set up to retrieve the aerodynamic roughness length from SAR data. Experiments based on ALOS PALSAR and COSMO-SkyMed data from 2006 to 2011 prove that the proposed methodology can provide accurate roughness length estimations for the spatial and temporal analysis of urban surface.

  9. Roughness coefficient and its uncertainty in gravel-bed river

    Directory of Open Access Journals (Sweden)

    Ji-Sung Kim

    2010-06-01

    Full Text Available Manning's roughness coefficient was estimated for a gravel-bed river reach using field measurements of water level and discharge, and the applicability of various methods used for estimation of the roughness coefficient was evaluated. Results show that the roughness coefficient tends to decrease with increasing discharge and water depth, and over a certain range it appears to remain constant. Comparison of roughness coefficients calculated by field measurement data with those estimated by other methods shows that, although the field-measured values provide approximate roughness coefficients for relatively large discharge, there seems to be rather high uncertainty due to the difference in resultant values. For this reason, uncertainty related to the roughness coefficient was analyzed in terms of change in computed variables. On average, a 20% increase of the roughness coefficient causes a 7% increase in the water depth and an 8% decrease in velocity, but there may be about a 15% increase in the water depth and an equivalent decrease in velocity for certain cross-sections in the study reach. Finally, the validity of estimated roughness coefficient based on field measurements was examined. A 10% error in discharge measurement may lead to more than 10% uncertainty in roughness coefficient estimation, but corresponding uncertainty in computed water depth and velocity is reduced to approximately 5%. Conversely, the necessity for roughness coefficient estimation by field measurement is confirmed.

  10. Rough Electrode Creates Excess Capacitance in Thin-Film Capacitors.

    Science.gov (United States)

    Torabi, Solmaz; Cherry, Megan; Duijnstee, Elisabeth A; Le Corre, Vincent M; Qiu, Li; Hummelen, Jan C; Palasantzas, George; Koster, L Jan Anton

    2017-08-16

    The parallel-plate capacitor equation is widely used in contemporary material research for nanoscale applications and nanoelectronics. To apply this equation, flat and smooth electrodes are assumed for a capacitor. This essential assumption is often violated for thin-film capacitors because the formation of nanoscale roughness at the electrode interface is very probable for thin films grown via common deposition methods. In this work, we experimentally and theoretically show that the electrical capacitance of thin-film capacitors with realistic interface roughness is significantly larger than the value predicted by the parallel-plate capacitor equation. The degree of the deviation depends on the strength of the roughness, which is described by three roughness parameters for a self-affine fractal surface. By applying an extended parallel-plate capacitor equation that includes the roughness parameters of the electrode, we are able to calculate the excess capacitance of the electrode with weak roughness. Moreover, we introduce the roughness parameter limits for which the simple parallel-plate capacitor equation is sufficiently accurate for capacitors with one rough electrode. Our results imply that the interface roughness beyond the proposed limits cannot be dismissed unless the independence of the capacitance from the interface roughness is experimentally demonstrated. The practical protocols suggested in our work for the reliable use of the parallel-plate capacitor equation can be applied as general guidelines in various fields of interest.

  11. Multi-scale analysis of the roughness effect on lubricated rough contact

    OpenAIRE

    DEMIRCI, Ibrahim

    2014-01-01

    Determining friction is as equally essential as determining the film thickness in the lubricated contact, and is an important research subject. Indeed, reduction of friction in the automotive industry is important for both the minimization of fuel consumption as well as the decrease in the emissions of greenhouse gases. However, the progress in friction reduction has been limited by the difficulty in understanding the mechanism of roughness effects on friction. It was observed that micro-surf...

  12. Rough surface mitigates electron and gas emission

    International Nuclear Information System (INIS)

    Molvik, A.

    2004-01-01

    Heavy-ion beams impinging on surfaces near grazing incidence (to simulate the loss of halo ions) generate copious amounts of electrons and gas that can degrade the beam. We measured emission coefficients of η e (le) 130 and η 0 ∼ 10 4 respectively, with 1 MeV K + incident on stainless steel. Electron emission scales as η e ∝ 1/cos(θ), where θ is the ion angle of incidence relative to normal. If we were to roughen a surface by blasting it with glass beads, then ions that were near grazing incidence (90 o ) on smooth surface would strike the rims of the micro-craters at angles closer to normal incidence. This should reduce the electron emission: the factor of 10 reduction, Fig. 1(a), implies an average angle of incidence of 62 o . Gas desorption varies more slowly with θ (Fig. 1(b)) decreasing a factor of ∼2, and along with the electron emission is independent of the angle of incidence on a rough surface. In a quadrupole magnet, electrons emitted by lost primary ions are trapped near the wall by the magnetic field, but grazing incidence ions can backscatter and strike the wall a second time at an azimuth where magnetic field lines intercept the beam. Then, electrons can exist throughout the beam (see the simulations of Cohen, HIF News 1-2/04). The SRIM (TRIM) Monte Carlo code predicts that 60-70% of 1 MeV K + ions backscatter when incident at 88-89 o from normal on a smooth surface. The scattered ions are mostly within ∼10 o of the initial direction but a few scatter by up to 90 o . Ion scattering decreases rapidly away from grazing incidence, Fig. 1(c ). At 62 deg. the predicted ion backscattering (from a rough surface) is 3%, down a factor of 20 from the peak, which should significantly reduce electrons in the beam from lost halo ions. These results are published in Phys. Rev. ST - Accelerators and Beams

  13. Influence of edge roughness on graphene nanoribbon resonant tunnelling diodes

    International Nuclear Information System (INIS)

    Liang Gengchiau; Khalid, Sharjeel Bin; Lam, Kai-Tak

    2010-01-01

    The edge roughness effects of graphene nanoribbons on their application in resonant tunnelling diodes with different geometrical shapes (S, H and W) were investigated. Sixty samples for each 5%, 10% and 15% edge roughness conditions of these differently shaped graphene nanoribbon resonant tunnelling diodes were randomly generated and studied. Firstly, it was observed that edge roughness in the barrier regions decreases the effective barrier height and thickness, which increases the broadening of the quantized states in the quantum well due to the enhanced penetration of the wave-function tail from the electrodes. Secondly, edge roughness increases the effective width of the quantum well and causes the lowering of the quantized states. Furthermore, the shape effects on carrier transport are modified by edge roughness due to different interfacial scattering. Finally, with the effects mentioned above, edge roughness has a considerable impact on the device performance in terms of varying the peak-current positions and degrading the peak-to-valley current ratio.

  14. A new fiber optic sensor for inner surface roughness measurement

    Science.gov (United States)

    Xu, Xiaomei; Liu, Shoubin; Hu, Hong

    2009-11-01

    In order to measure inner surface roughness of small holes nondestructively, a new fiber optic sensor is researched and developed. Firstly, a new model for surface roughness measurement is proposed, which is based on intensity-modulated fiber optic sensors and scattering modeling of rough surfaces. Secondly, a fiber optical measurement system is designed and set up. Under the help of new techniques, the fiber optic sensor can be miniaturized. Furthermore, the use of micro prism makes the light turn 90 degree, so the inner side surface roughness of small holes can be measured. Thirdly, the fiber optic sensor is gauged by standard surface roughness specimens, and a series of measurement experiments have been done. The measurement results are compared with those obtained by TR220 Surface Roughness Instrument and Form Talysurf Laser 635, and validity of the developed fiber optic sensor is verified. Finally, precision and influence factors of the fiber optic sensor are analyzed.

  15. Turbulent flow with suction in smooth and rough pipes

    International Nuclear Information System (INIS)

    Verdier, Andre.

    1977-11-01

    It concerns an experimental study of turbulent flow inside a pipe with rough and porous wall and suction applied through it. The first part recall the basic knowledge concerning the turbulent flow with roughness. In second part statistical equations of fluid wall stress are written in the case of a permeable rough wall, in order to underline the respective role played by viscosity and pressure terms. In the third part the dynamic equilibrium of the flow is experimentally undertaken in the smooth and rough range with and without wall suction. Some empirical formulae are proposed for the mean velocity profiles in the inertial range and for friction velocity with suction. In the case of the sand roughness used, it does not seem that critical Reynolds number of transition from smooth to rough range is varied [fr

  16. Numerical simulations of seepage flow in rough single rock fractures

    Directory of Open Access Journals (Sweden)

    Qingang Zhang

    2015-09-01

    Full Text Available To investigate the relationship between the structural characteristics and seepage flow behavior of rough single rock fractures, a set of single fracture physical models were produced using the Weierstrass–Mandelbrot functions to test the seepage flow performance. Six single fractures, with various surface roughnesses characterized by fractal dimensions, were built using COMSOL multiphysics software. The fluid flow behavior through the rough fractures and the influences of the rough surfaces on the fluid flow behavior was then monitored. The numerical simulation indicates that there is a linear relationship between the average flow velocity over the entire flow path and the fractal dimension of the rough surface. It is shown that there is good a agreement between the numerical results and the experimental data in terms of the properties of the fluid flowing through the rough single rock fractures.

  17. Effect of truncated cone roughness element density on hydrodynamic drag

    Science.gov (United States)

    Womack, Kristofer; Schultz, Michael; Meneveau, Charles

    2017-11-01

    An experimental study was conducted on rough-wall, turbulent boundary layer flow with roughness elements whose idealized shape model barnacles that cause hydrodynamic drag in many applications. Varying planform densities of truncated cone roughness elements were investigated. Element densities studied ranged from 10% to 79%. Detailed turbulent boundary layer velocity statistics were recorded with a two-component LDV system on a three-axis traverse. Hydrodynamic roughness length (z0) and skin-friction coefficient (Cf) were determined and compared with the estimates from existing roughness element drag prediction models including Macdonald et al. (1998) and other recent models. The roughness elements used in this work model idealized barnacles, so implications of this data set for ship powering are considered. This research was supported by the Office of Naval Research and by the Department of Defense (DoD) through the National Defense Science & Engineering Graduate Fellowship (NDSEG) Program.

  18. Irregular wall roughness in turbulent Taylor-Couette flow

    Science.gov (United States)

    Berghout, Pieter; Zhu, Xiaojue; Verzicco, Roberto; Lohse, Detlef; Stevens, Richard

    2017-11-01

    Many wall bounded flows in nature, engineering and transport are affected by surface roughness. Often, this has adverse effects, e.g. drag increase leading to higher energy costs. A major difficulty is the infinite number of roughness geometries, which makes it impossible to systematically investigate all possibilities. Here we present Direct Numerical Simulations (DNS) of turbulent Taylor-Couette flow. We focus on the transitionally rough regime, in which both viscous and pressure forces contribute to the total wall stress. We investigate the effect of the mean roughness height and the effective slope on the roughness function, ΔU+ . Also, we present simulations of varying Ta (Re) numbers for a constant mean roughness height (kmean+). Alongside, we show the behavior of the large scale structures (e.g. plume ejection, Taylor rolls) and flow structures in the vicinity of the wall.

  19. Turbulence modifications in a turbulent boundary layer over a rough wall with spanwise-alternating roughness strips

    Science.gov (United States)

    Bai, H. L.; Kevin, Hutchins, N.; Monty, J. P.

    2018-05-01

    Turbulence modifications over a rough wall with spanwise-varying roughness are investigated at a moderate Reynolds number Reτ ≈ 2000 (or Reθ ≈ 6400), using particle image velocimetry (PIV) and hotwire anemometry. The rough wall is comprised of spanwise-alternating longitudinal sandpaper strips of two different roughness heights. The ratio of high- and low-roughness heights is 8, and the ratio of high- and low-roughness strip width is 0.5. PIV measurements are conducted in a wall-parallel plane located in the logarithmic region, while hotwire measurements are made throughout the entire boundary layer in a cross-stream plane. In a time-average sense, large-scale counter-rotating roll-modes are observed in the cross-stream plane over the rough wall, with downwash and upwash common-flows displayed over the high- and low-roughness strips, respectively. Meanwhile, elevated and reduced streamwise velocities occur over the high- and low-roughness strips, respectively. Significant modifications in the distributions of mean vorticities and Reynolds stresses are observed, exhibiting features of spatial preference. Furthermore, spatial correlations and conditional average analyses are performed to examine the alterations of turbulence structures over the rough wall, revealing that the time-invariant structures observed are resultant from the time-average process of instantaneous turbulent events that occur mostly and preferentially in space.

  20. Incorporating Skew into RMS Surface Roughness Probability Distribution

    Science.gov (United States)

    Stahl, Mark T.; Stahl, H. Philip.

    2013-01-01

    The standard treatment of RMS surface roughness data is the application of a Gaussian probability distribution. This handling of surface roughness ignores the skew present in the surface and overestimates the most probable RMS of the surface, the mode. Using experimental data we confirm the Gaussian distribution overestimates the mode and application of an asymmetric distribution provides a better fit. Implementing the proposed asymmetric distribution into the optical manufacturing process would reduce the polishing time required to meet surface roughness specifications.

  1. Investigation of surface roughness influence on hyperbolic metamaterial performance

    Directory of Open Access Journals (Sweden)

    S. Kozik

    2014-12-01

    Full Text Available The main goal of this work was to introduce simple model of surface roughness which does not involve objects with complicated shapes and could help to reduce computational costs. We described and proved numerically that the influence of surface roughness at the interfaces in metal-dielectric composite materials could be described by proper selection of refractive index of dielectric layers. Our calculations show that this model works for roughness with RMS value about 1 nm and below.

  2. legrænser for luftforurening: Anvendelse i strategisk miljøplanlægning

    DEFF Research Database (Denmark)

    Bastrup-Birk, A.; Tybirk, K.; Wier, M.

    The report describes and discusses the principle of Critical Loads and Critical Levels in relation to strategic environmental planning. The DPSIR-chain explanatory variables are used as a framework for the process if integrating economics, chemistry and ecology in the field of acidifying...

  3. Constraining the roughness degree of slip heterogeneity

    KAUST Repository

    Causse, Mathieu

    2010-05-07

    This article investigates different approaches for assessing the degree of roughness of the slip distribution of future earthquakes. First, we analyze a database of slip images extracted from a suite of 152 finite-source rupture models from 80 events (Mw = 4.1–8.9). This results in an empirical model defining the distribution of the slip spectrum corner wave numbers (kc) as a function of moment magnitude. To reduce the “epistemic” uncertainty, we select a single slip model per event and screen out poorly resolved models. The number of remaining models (30) is thus rather small. In addition, the robustness of the empirical model rests on a reliable estimation of kc by kinematic inversion methods. We address this issue by performing tests on synthetic data with a frequency domain inversion method. These tests reveal that due to smoothing constraints used to stabilize the inversion process, kc tends to be underestimated. We then develop an alternative approach: (1) we establish a proportionality relationship between kc and the peak ground acceleration (PGA), using a k−2 kinematic source model, and (2) we analyze the PGA distribution, which is believed to be better constrained than slip images. These two methods reveal that kc follows a lognormal distribution, with similar standard deviations for both methods.

  4. Spectrophotometric Examination of Rough Print Surfaces

    Directory of Open Access Journals (Sweden)

    Erzsébet Novotny

    2011-05-01

    Full Text Available The objective was to assess the impact of the surface texture of individual creative paper types (coated or patternedon the quality of printing and to identify to what extent the various creative paper types require specific types ofspectrophotometers. We used stereomicroscopic images to illustrate unprinted and printed surfaces of creative papertypes. Surface roughness was measured to obtain data on the unevenness of surfaces. Spectrophotometric tests wereused to select the most suitable spectrophotometer from meters with different illumination setup for testing anygiven print. For the purpose of testing, we used spectrophotometers which are commonly available generally used totest print products for colour accuracy. With the improvement of measuring geometries, illumination setup, colourmeasurement becomes more and more capable of producing reliable results unaffected by surface textures. Our testshave proved this fact by showing that the GretagMacbeth Spectrolino with annular illumination is less sensitive tosurface texture than the X-Rite Spetrodensitometer and the Techkon SpetroDens with directional illumination. Furthertests have brought us to the conclusion that there is a difference even between the two devices with directionalillumination. While the X-Rite 530 Spectrodensitometer is more suitable for testing coated surfaces, the TechkonSpectroDens can come close to ΔE*ab values produced by the annular illuminated device for textured surfaces.

  5. Radiosensitivity of the rough-skinned newt

    International Nuclear Information System (INIS)

    Willis, D.L.; Lappenbusch, W.L.

    1974-01-01

    Newts were collected locally and maintained unfed at 10 0 C both before and after irradiation. Whole-body exposures ranging up to 80 kR were given with 250 kVp x rays, 300 kVp x rays, and 60 Co gamma rays. The mean survival time-exposure curve was sigmoid, following the typical appearance of such curves for mammalian species. A dose-independent region extending from roughly 700 to 5,000 R was evident. A variety of skin lesions and depigmentation effects were noted at exposures above 250 R, whose time of appearance decreased with increasing dose. A total of 832 newts were used in this phase of the study. Assuming that hematopoietic damage was primarily responsible for deaths below 700-800 R, additional studies of hematopoiesis were initiated. The effect of a 650 R-exposure on liver weight, spleen weight and concentration of circulating red blood cells for 1 1 / 2 months post-irradiation was assessed. The results indicate a progressive state of anemia. This was further substantiated by a study of 59 Fe incorporation by red blood cells at intervals up to one month for five exposures ranging up to 1000 R. (U.S.)

  6. Estimation of fracture roughness from the acoustic borehole televiewer image

    International Nuclear Information System (INIS)

    Bae, Dae Soek; Kim, Chun Soo; Kim, Kyung Soo; Park, Byung Yoon; Koh, Yong Kweon

    2000-12-01

    Estimation of fracture roughness - as one of the basic hydraulic fracture parameters - is very important in assessing ground water flow described by using discrete fracture network modeling. Former manual estimation of the roughness for each fracture surface of drill cores is above all a tedious, time-consuming work and will often cause some ambiguities of roughness interpretation partly due to the subjective judgements of observers, and partly due to the measuring procedure itself. However, recently, indebt to the highly reliable Televiewer data for the fracture discrimination, it has led to a guess to develop a relationship between the traditional roughness method based on a linear profiles and the method from the Televiewer image based on a ellipsoidal profile. Hence, the aim of this work is to develop an automatic evaluation algorithm for measuring the roughness from the Televiewer images. A highly reliable software named 'FRAFA' has been developed and realized to the extent that its utility merits. In the developing procedure, various problems - such as the examination of a new base line(ellipsoidal) for measuring the unevenness of fracture, the elimination of overlapping fracture signatures or noise, the wavelet estimation according to the type of fractures and the digitalization of roughness etc. - were considered. With these consideration in mind, the newly devised algorithm for the estimation of roughness curves showed a great potential not only for avoiding ambiguities of roughness interpretation but also for the judgement of roughness classification

  7. Estimating deep seafloor interface and volume roughness parameters using the multibeam-hydrosweep system

    Digital Repository Service at National Institute of Oceanography (India)

    Chakraborty, B.; Schenke, H.W.; Kodagali, V.N.; Hagen, R.

    composite roughness model, including water-sediment interface roughness and sediment volume roughness parameters the data was modeled. The model effectively uses the near normal incidence angle backscatter to determine the seafloor interface roughness...

  8. Rendimento e composição química de cultivares de milho em moagem a seco e produção de grits Yield and chemical composition of corn cultivate in dry-milling and grits production

    Directory of Open Access Journals (Sweden)

    Rogério Amaro Gonçalves

    2003-06-01

    Full Text Available O milho é uma das principais matérias-primas para a indústria de alimentos. Desse cereal, é possível obter óleo, fubá, canjica, grits, farelo, amido e zeína. Conduziu-se este trabalho com o objetivo de avaliar o rendimento de moagem a seco, produção de grits e composição química de 16 cultivares de milho. Os grãos de milho das 16 cultivares avaliadas tiveram a sua umidade padronizada para 12% e foram submetidos a um processo de limpeza em uma mesa gravimétrica. Encerrada a etapa de limpeza, foram colocados 10 kg de grãos de cada cultivar em degerminador de facas com rotação de 600 rpm por um período de 10 minutos. Após a degerminação, o endosperma foi passado por moinho de rolos corrugados com distância entre rolos de 30 mm. O material moído foi submetido à tamisação em peneiras de 14, 20, 25 e 30 mesh por um período de 10 minutos. Para a degerminação, o delineamento experimental utilizado foi o inteiramente casualizado, com um fator de 16 cultivares e 2 repetições. Na tamisação, o delineamento usado foi com dois fatores: 16 cultivares, 5 peneiras e 2 repetições. A cultivar BR-106, o híbrido duplo BRS-2114 e o híbrido triplo BR-3123 registraram maiores rendimentos (PMaize is one of the major source of energetic an nutritious ingredient for the food industry. From the maize grain it is possible to get oil, meal, grits, bran, starch, zein. The objectives of this research was to evaluate the dry-miling yield and chemical composition of different experimental maize genotypes. Fourteen genotypes came from the breeding program of Embrapa Corn and Sorghum Researcher Center and two came from commercial companies. The grain moisture content of all cultivars were equilibrated at 12% and dust was removed in a gravimetric board, before processing. Grain samples of each type was placed in a blade degermer at 600 rpm rotation speed for 10 minutes. The endosperm portion, after degermination, was transferred to a mill roll

  9. Performance of laser sintered Ti-6Al-4V implants with bone-inspired porosity and micro/nanoscale surface roughness in the rabbit femur.

    Science.gov (United States)

    Cohen, David J; Cheng, Alice; Sahingur, Kaan; Clohessy, Ryan M; Hopkins, Louis B; Boyan, Barbara D; Schwartz, Zvi

    2017-04-28

    Long term success of bone-interfacing implants remains a challenge in compromised patients and in areas of low bone quality. While surface roughness at the micro/nanoscale can promote osteogenesis, macro-scale porosity is important for promoting mechanical stability of the implant over time. Currently, machining techniques permit pores to be placed throughout the implant, but the pores are generally uniform in dimension. The advent of laser sintering provides a way to design and manufacture implants with specific porosity and variable dimensions at high resolution. This approach enables production of metal implants that mimic complex geometries found in biology. In this study, we used a rabbit femur model to compare osseointegration of laser sintered solid and porous implants. Ti-6Al-4V implants were laser sintered in a clinically relevant size and shape. One set of implants had a novel porosity based on human trabecular bone; both sets had grit-blasted/acid-etched surfaces. After characterization, implants were inserted transaxially into rabbit femora; mechanical testing, micro-computed tomography (microCT) and histomorphometry were conducted 10 weeks post-operatively. There were no differences in pull-out strength or bone-to-implant contact. However, both microCT and histomorphometry showed significantly higher new bone volume for porous compared to solid implants. Bone growth was observed into porous implant pores, especially near apical portions of the implant interfacing with cortical bone. These results show that laser sintered Ti-6Al-4V implants with micro/nanoscale surface roughness and trabecular bone-inspired porosity promote bone growth and may be used as a superior alternative to solid implants for bone-interfacing implants.

  10. Fuzzy multi-project rough-cut capacity planning

    NARCIS (Netherlands)

    Masmoudi, Malek; Hans, Elias W.; Leus, Roel; Hait, Alain; Sotskov, Yuri N.; Werner, Frank

    2014-01-01

    This chapter studies the incorporation of uncertainty into multi-project rough-cut capacity planning. We use fuzzy sets to model uncertainties, adhering to the so-called possibilistic approach. We refer to the resulting proactive planning environment as Fuzzy Rough Cut Capacity Planning (FRCCP).

  11. Sub-Patch Roughness in Earthquake Rupture Investigations

    KAUST Repository

    Zielke, Olaf

    2016-02-13

    Fault geometric complexities exhibit fractal characteristics over a wide range of spatial scales (<µm to >km) and strongly affect the rupture process at corresponding scales. Numerical rupture simulations provide a framework to quantitatively investigate the relationship between a fault\\'s roughness and its seismic characteristics. Fault discretization however introduces an artificial lower limit to roughness. Individual fault patches are planar and sub-patch roughnessroughness at spatial scales below fault-patch size– is not incorporated. Does negligence of sub-patch roughness measurably affect the outcome of earthquake rupture simulations? We approach this question with a numerical parameter space investigation and demonstrate that sub-patch roughness significantly modifies the slip-strain relationship –a fundamental aspect of dislocation theory. Faults with sub-patch roughness induce less strain than their planar-fault equivalents at distances beyond the length of a slipping fault. We further provide regression functions that characterize the stochastic effect sub-patch roughness.

  12. Heat transfer and pressure drop in microchannels with random roughness

    NARCIS (Netherlands)

    Pelevic, N.; van der Meer, Theodorus H.

    2016-01-01

    The effect of surface roughness on heat transfer and fluid flow phenomena within a microchannel has been investigated by using the lattice Boltzmann method. The surface roughness has been generated by using Gaussian function. Gaussian function is an efficient and convenient method to create surface

  13. Assessing of channel roughness and temperature variations on ...

    African Journals Online (AJOL)

    Assessing of channel roughness and temperature variations on wastewater quality parameters using numerical modeling. ... According to the obtained results, nitrate (NO3) has a decreasing trend when the Manning Roughness Coefficient (N) is higher than 0.04 along the channel, but is reduced when “N” is less than 0.04.

  14. Gliding Swifts Attain Laminar Flow over Rough Wings

    NARCIS (Netherlands)

    Lentink, D.; Kat, de R.

    2014-01-01

    Swifts are among the most aerodynamically refined gliding birds. However, the overlapping vanes and protruding shafts of their primary feathers make swift wings remarkably rough for their size. Wing roughness height is 1–2% of chord length on the upper surface—10,000 times rougher than sailplane

  15. Surface roughness effects on heat transfer in Couette flow

    International Nuclear Information System (INIS)

    Elia, G.G.

    1981-01-01

    A cell theory for viscous flow with rough surfaces is applied to two basic illustrative heat transfer problems which occur in Couette flow. Couette flow between one adiabatic surface and one isothermal surface exhibits roughness effects on the adiabatic wall temperature. Two types of rough cell adiabatic surfaces are studied: (1) perfectly insulating (the temperature gradient vanishes at the boundary of each cell); (2) average insulating (each cell may gain or lose heat but the total heat flow at the wall is zero). The results for the roughness on a surface in motion are postulated to occur because of fluid entrainment in the asperities on the moving surface. The symmetry of the roughness effects on thermal-viscous dissipation is discussed in detail. Explicit effects of the roughness on each surface, including combinations of roughness values, are presented to enable the case where the two surfaces may be from different materials to be studied. The fluid bulk temperature rise is also calculated for Couette flow with two ideal adiabatic surfaces. The effect of roughness on thermal-viscous dissipation concurs with the viscous hydrodynamic effect. The results are illustrated by an application to lubrication. (Auth.)

  16. A Meta-Analysis: Acoustic Measurement of Roughness and Breathiness

    Science.gov (United States)

    v. Latoszek, Ben Barsties; Maryn, Youri; Gerrits, Ellen; De Bodt, Marc

    2018-01-01

    Purpose: Over the last 5 decades, many acoustic measures have been created to measure roughness and breathiness. The aim of this study is to present a meta-analysis of correlation coefficients (r) between auditory-perceptual judgment of roughness and breathiness and various acoustic measures in both sustained vowels and continuous speech. Method:…

  17. Road roughness evaluation using in-pavement strain sensors

    Science.gov (United States)

    Zhang, Zhiming; Deng, Fodan; Huang, Ying; Bridgelall, Raj

    2015-11-01

    The international roughness index (IRI) is a characterization of road roughness or ride quality that transportation agencies most often report. The prevalent method of acquiring IRI data requires instrumented vehicles and technicians with specialized training to interpret the results. The extensive labor and high cost requirements associated with the existing approaches limit data collection to at most once per year for portions of the national highway system. Agencies characterize roughness only for some secondary roads but much less frequently, such as once every five years, resulting in outdated roughness information. This research developed a real-time roughness evaluation approach that links the output of durable in-pavement strain sensors to prevailing indices that summarize road roughness. Field experiments validated the high consistency of the approach by showing that it is within 3.3% of relative IRI estimates. After their installation and calibration during road construction, the ruggedized strain sensors will report road roughness continuously. Thus, the solution will provide agencies a real-time roughness monitoring solution over the remaining service life of road assets.

  18. Model of rough bed for numerical simulation of saltation

    Czech Academy of Sciences Publication Activity Database

    Kharlamova, Irina; Vlasák, Pavel

    2015-01-01

    Roč. 19, č. 3 (2015), s. 366-385 ISSN 1964-8189 R&D Projects: GA ČR GA103/09/1718; GA ČR GAP105/10/1574 Institutional support: RVO:67985874 Keywords : saltation * bed load transport * rough bed * armoured bed * bed roughness Subject RIV: BK - Fluid Dynamics Impact factor: 0.636, year: 2015

  19. PhysarumSoft: An update based on rough set theory

    Science.gov (United States)

    Schumann, Andrew; Pancerz, Krzysztof

    2017-07-01

    PhysarumSoft is a software tool consisting of two modules developed for programming Physarum machines and simulating Physarum games, respectively. The paper briefly discusses what has been added since the last version released in 2015. New elements in both modules are based on rough set theory. Rough sets are used to model behaviour of Physarum machines and to describe strategy games.

  20. Roughness effect on the efficiency of dimer antenna based biosensor

    Directory of Open Access Journals (Sweden)

    D. Barchiesi

    2012-09-01

    Full Text Available The fabrication process of nanodevices is continually improved. However, most of the nanodevices, such as biosensors present rough surfaces with mean roughness of some nanometers even if the deposition rate of material is more controlled. The effect of roughness on performance of biosensors was fully addressed for plane biosensors and gratings, but rarely addressed for biosensors based on Local Plasmon Resonance. The purpose of this paper is to evaluate numerically the influence of nanometric roughness on the efficiency of a dimer nano-biosensor (two levels of roughness are considered. Therefore, we propose a general numerical method, that can be applied to any other nanometric shape, to take into account the roughness in a three dimensional model. The study focuses on both the far-field, which corresponds to the experimental detected data, and the near-field, responsible for exciting and then detecting biological molecules. The results suggest that the biosensor efficiency is highly sensitive to the surface roughness. The roughness can produce important shifts of the extinction efficiency peak and a decrease of its amplitude resulting from changes in the distribution of near-field and absorbed electric field intensities.

  1. Roughness of grain boundaries in partly recrystallized aluminum

    DEFF Research Database (Denmark)

    Sun, Jun; Zhang, Yubin; Juul Jensen, Dorte

    2017-01-01

    cold rolled aluminum samples. The results show that particle pinning is not the main reason accounting for recrystallization boundary roughness in the present samples. The roughness is however shown to relate to the deformation microstructure and possible effects of migration rate are discussed...

  2. Rough Mill Improvement Guide for Managers and Supervisors

    Science.gov (United States)

    Philip H. Mitchell; Jan Wiedenbeck; Bobby Ammerman; Bobby Ammerman

    2005-01-01

    Wood products manufacturers require an efficient recovery of product from lumber to remain profitable. A company's ability to obtain the best yield in lumber cut-up operations (i.e., the rough mill) varies according to the raw material, product, processing equipment, processing environment, and knowledge and skill of the rough mill's employees. This book...

  3. The Terahertz Scattering Analysis of Rough Metallic and Dielectric Targets

    Directory of Open Access Journals (Sweden)

    Mou Yuan

    2018-02-01

    Full Text Available The terahertz scattering characteristics of metallic and dielectric rough targets is important for the investigation of the terahertz radar targets properties. According to the stationary phase theory and scalar approximation, if the radius of curvature at any point of the surface is much larger than the incident wavelength, and the wavelength is also much longer than the surface height function and Root-Mean-Square (RMS surface slope, the coherent and incoherent scattering Radar Cross Section (RCS of rough metallic and dielectric targets can be obtained. Based on the stationary phase approximation, the coherent RCS of rough conductors, smooth dielectric targets and rough dielectric targets can be easily deputed. The scattering characteristics of electrically large smooth Al and painted spheres are investigated in this paper, and the calculated RCS are verified by Mie scattering theory, the error is less than 0.1 dBm2. Based on lambert theory, it is demonstrated that the incoherent RCS is analyzed with better precision if the rough surfaces are divided into much more facets. In this paper, the coherent and incoherent scattering of rough Al and painted spheres are numerically observed, and the effects of surface roughness and materials are analyzed. The conclusions provide theoretical foundation for the terahertz scattering characteristics of electrically large rough targets.

  4. An intermittency model for predicting roughness induced transition

    Science.gov (United States)

    Ge, Xuan; Durbin, Paul

    2014-11-01

    An extended model for roughness-induced transition is proposed based on an intermittency transport equation for RANS modeling formulated in local variables. To predict roughness effects in the fully turbulent boundary layer, published boundary conditions for k and ω are used, which depend on the equivalent sand grain roughness height, and account for the effective displacement of wall distance origin. Similarly in our approach, wall distance in the transition model for smooth surfaces is modified by an effective origin, which depends on roughness. Flat plate test cases are computed to show that the proposed model is able to predict the transition onset in agreement with a data correlation of transition location versus roughness height, Reynolds number, and inlet turbulence intensity. Experimental data for a turbine cascade are compared with the predicted results to validate the applicability of the proposed model. Supported by NSF Award Number 1228195.

  5. Comparison of optical methods for surface roughness characterization

    DEFF Research Database (Denmark)

    Feidenhans'l, Nikolaj Agentoft; Hansen, Poul Erik; Pilny, Lukas

    2015-01-01

    We report a study of the correlation between three optical methods for characterizing surface roughness: a laboratory scatterometer measuring the bi-directional reflection distribution function (BRDF instrument), a simple commercial scatterometer (rBRDF instrument), and a confocal optical profiler....... For each instrument, the effective range of spatial surface wavelengths is determined, and the common bandwidth used when comparing the evaluated roughness parameters. The compared roughness parameters are: the root-mean-square (RMS) profile deviation (Rq), the RMS profile slope (Rdq), and the variance...... of the scattering angle distribution (Aq). The twenty-two investigated samples were manufactured with several methods in order to obtain a suitable diversity of roughness patterns.Our study shows a one-to-one correlation of both the Rq and the Rdq roughness values when obtained with the BRDF and the confocal...

  6. Computer simulation of RBS spectra from samples with surface roughness

    Energy Technology Data Exchange (ETDEWEB)

    Malinský, P., E-mail: malinsky@ujf.cas.cz [Nuclear Physics Institute of the Academy of Sciences of the Czech Republic, v. v. i., 250 68 Rez (Czech Republic); Department of Physics, Faculty of Science, J. E. Purkinje University, Ceske mladeze 8, 400 96 Usti nad Labem (Czech Republic); Hnatowicz, V., E-mail: hnatowicz@ujf.cas.cz [Nuclear Physics Institute of the Academy of Sciences of the Czech Republic, v. v. i., 250 68 Rez (Czech Republic); Macková, A., E-mail: mackova@ujf.cas.cz [Nuclear Physics Institute of the Academy of Sciences of the Czech Republic, v. v. i., 250 68 Rez (Czech Republic); Department of Physics, Faculty of Science, J. E. Purkinje University, Ceske mladeze 8, 400 96 Usti nad Labem (Czech Republic)

    2016-03-15

    A fast code for the simulation of common RBS spectra including surface roughness effects has been written and tested on virtual samples comprising either a rough layer deposited on a smooth substrate or smooth layer deposited on a rough substrate and simulated at different geometries. The sample surface or interface relief has been described by a polyline and the simulated RBS spectrum has been obtained as the sum of many particular spectra from randomly chosen particle trajectories. The code includes several procedures generating virtual samples with random and regular (periodical) roughness. The shape of the RBS spectra has been found to change strongly with increasing sample roughness and an increasing angle of the incoming ion beam.

  7. Quantized Ultracold Neutrons in Rough Waveguides: GRANIT Experiments and Beyond

    Directory of Open Access Journals (Sweden)

    M. Escobar

    2014-01-01

    Full Text Available We apply our general theory of transport in systems with random rough boundaries to gravitationally quantized ultracold neutrons in rough waveguides as in GRANIT experiments (ILL, Grenoble. We consider waveguides with roughness in both two and one dimensions (2D and 1D. In the biased diffusion approximation the depletion times for the gravitational quantum states can be easily expressed via each other irrespective of the system parameters. The calculation of the exit neutron count reduces to evaluation of a single constant which contains a complicated integral of the correlation function of surface roughness. In the case of 1D roughness (random grating this constant is calculated analytically for common types of the correlation functions. The results obey simple scaling relations which are slightly different in 1D and 2D. We predict the exit neutron count for the new GRANIT cell.

  8. Roughness Sensitivity Comparisons of Wind Turbine Blade Sections

    Energy Technology Data Exchange (ETDEWEB)

    Wilcox, Benjamin J. [Texas A & M Univ., College Station, TX (United States). Dept. of Aerospace Engineering; White, Edward B. [Texas A & M Univ., College Station, TX (United States). Dept. of Aerospace Engineering; Maniaci, David Charles [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Wind Energy Technologies Dept.

    2017-10-01

    One explanation for wind turbine power degradation is insect roughness. Historical studies on insect-induced power degradation have used simulation methods which are either un- representative of actual insect roughness or too costly or time-consuming to be applied to wide-scale testing. Furthermore, the role of airfoil geometry in determining the relations between insect impingement locations and roughness sensitivity has not been studied. To link the effects of airfoil geometry, insect impingement locations, and roughness sensitivity, a simulation code was written to determine representative insect collection patterns for different airfoil shapes. Insect collection pattern data was then used to simulate roughness on an NREL S814 airfoil that was tested in a wind tunnel at Reynolds numbers between 1.6 x 106 and 4.0 x 106. Results are compared to previous tests of a NACA 633 -418 airfoil. Increasing roughness height and density results in decreased maximum lift, lift curve slope, and lift-to-drag ratio. Increasing roughness height, density, or Reynolds number results in earlier bypass transition, with critical roughness Reynolds numbers lying within the historical range. Increased roughness sensitivity on the 25% thick NREL S814 is observed compared to the 18% thick NACA 63 3 -418. Blade-element-momentum analysis was used to calculate annual energy production losses of 4.9% and 6.8% for a NACA 633 -418 turbine and an NREL S814 turbine, respectively, operating with 200 μm roughness. These compare well to historical field measurements.

  9. The role of the roughness spectral breadth in elastic contact of rough surfaces

    Science.gov (United States)

    Yastrebov, Vladislav A.; Anciaux, Guillaume; Molinari, Jean-François

    2017-10-01

    We study frictionless and non-adhesive contact between elastic half-spaces with self-affine surfaces. Using a recently suggested corrective technique, we ensure an unprecedented accuracy in computation of the true contact area evolution under increasing pressure. This accuracy enables us to draw conclusions on the role of the surface's spectrum breadth (Nayak parameter) in the contact area evolution. We show that for a given normalized pressure, the contact area decreases logarithmically with the Nayak parameter. By linking the Nayak parameter with the Hurst exponent (or fractal dimension), we show the effect of the latter on the true contact area. This effect, undetectable for surfaces with poor spectral content, is quite strong for surfaces with rich spectra. Numerical results are compared with analytical models and other available numerical results. A phenomenological equation for the contact area growth is suggested with coefficients depending on the Nayak parameter. Using this equation, the pressure-dependent friction coefficient is deduced based on the adhesive theory of friction. Some observations on Persson's model of rough contact, whose prediction does not depend on Nayak parameter, are reported. Overall, the paper provides a unifying picture of rough elastic contact and clarifies discrepancies between preceding results.

  10. Evaluation of the Effect of Surface Polishing, Oral Beverages and Food Colorants on Color Stability and Surface Roughness of Nanocomposite Resins.

    Science.gov (United States)

    Kumari, R Veena; Nagaraj, Hema; Siddaraju, Kishore; Poluri, Ramya Krishna

    2015-07-01

    It is beyond doubt that finishing and polishing of a composite restoration enhance its esthetics and, is also essential for the health of the periodontium. A variety of instruments are commonly used for finishing and polishing tooth-colored restorative materials Thus, it is important to understand which type of surface finishing treatments would significantly affect the staining and surface irregularities of the composite resin restoration. Still one of the properties of the composite resins that have to pass the test of time is its color stability. In modern day dentistry, a large emphasis is laid over esthetics. Hence, it is important to understand the various agents capable of adversely affecting the esthetics of a restoration due to its staining capacity. Thus, the aim of this in vitro study was to evaluate the effect of surface polishing, oral beverages and food colorants on the color stability and surface roughness of nanocomposite resins. 90 Disks of nanocomposites resin (Filtek Z350 XT) measuring 8 mm in diameter and 2 mm in thickness were fabricated using a custom made silicon mold. Pre-polishing surface roughness (Ra1) of all the 90 samples were measured using a Surface Profilometer. The nano-composite disks were then randomly divided into 3 groups with 30 samples in each group. Group I: The samples were not subjected to any polishing procedures. Group II: Sof-Lex group: Samples subjected to polishing using different grits of Sof-Lex disks. Group III: Diamond polishing paste group: Samples were subjected with a polishing paste consisting of diamond particles. Following polishing procedures, the surface roughness of all samples were measured again to obtain change in surface roughness due to polishing procedures (Ra2), pre immersion spectrophotometric value (ΔE1) was also recorded for baseline color of the samples. The samples were then divided into subgroups (A, B, C, D, E), by including every first sample in Subgroup A, second in Subgroup B, third in

  11. COMPARATIVE STUDY OF LUNAR ROUGHNESS FROM MULTI - SOURCE DATA

    Directory of Open Access Journals (Sweden)

    Y. Lou

    2017-07-01

    Full Text Available The lunar terrain can show its collision and volcanic history. The lunar surface roughness can give a deep indication of the effects of lunar surface magma, sedimentation and uplift. This paper aims to get different information from the roughness through different data sources. Besides introducing the classical Root-mean-square height method and Morphological Surface Roughness (MSR algorithm, this paper takes the area of the Jurassic mountain uplift in the Sinus Iridum and the Plato Crater area as experimental areas. And then make the comparison and contrast of the lunar roughness derived from LRO's DEM and CE-2 DOM. The experimental results show that the roughness obtained by the traditional roughness calculation method reflect the ups and downs of the topography, while the results obtained by morphological surface roughness algorithm show the smoothness of the lunar surface. So, we can first use the surface fluctuation situation derived from RMSH to select the landing area range which ensures the lands are gentle. Then the morphological results determine whether the landing area is suitable for the detector walking and observing. The results obtained at two different scales provide a more complete evaluation system for selecting the landing site of the lunar probe.

  12. Numerical simulation of wall roughness effects in cavitating flow

    International Nuclear Information System (INIS)

    Echouchene, F.; Belmabrouk, H.; Le Penven, L.; Buffat, M.

    2011-01-01

    Hydrodynamic cavitation has an important effect on the performance of Diesel injectors. It influences the nature of the fuel spray and the efficiency of the combustion process. In the present study, we investigate numerically the effect of wall roughness in the cavitating and turbulent flow developing inside a Diesel injector. The mixture model based on a single fluid is adopted and the commercial Fluent software is used to solve the transport equations. The discharge coefficient C d is computed for different cavitation numbers and wall roughness heights. Profiles of density mixture, vapor volume fraction, mean velocity and turbulent kinetic energy are reported. The effects of wall roughness and injection pressure are analyzed.

  13. Effects of capillary condensation in adhesion between rough surfaces.

    Science.gov (United States)

    Wang, Jizeng; Qian, Jin; Gao, Huajian

    2009-10-06

    Experiments on the effects of humidity in adhesion between rough surfaces have shown that the adhesion energy remains constant below a critical relative humidity (RHcr) and then abruptly jumps to a higher value at RHcr before approaching its upper limit at 100% relative humidity. A model based on a hierarchical rough surface topography is proposed, which quantitatively explains the experimental observations and predicts two threshold RH values, RHcr and RHdry, which define three adhesion regimes: (1) RHRHcr, water menisci freely form and spread along the interface between the rough surfaces.

  14. On the computation of the turbulent flow near rough surface

    Science.gov (United States)

    Matveev, S. K.; Jaychibekov, N. Zh.; Shalabayeva, B. S.

    2018-05-01

    One of the problems in constructing mathematical models of turbulence is a description of the flows near a rough surface. An experimental study of such flows is also difficult because of the impossibility of measuring "inside" the roughness. The theoretical calculation is difficult because of the lack of equations describing the flow in this zone. In this paper, a new turbulence model based on the differential equation of turbulent viscosity balance was used to describe a turbulent flow near a rough surface. The difference between the new turbulence model and the previously known consists in the choice of constants and functions that determine the generation, dissipation and diffusion of viscosity.

  15. Echo signal from rough planar interfaces influence of roughness, angle, range and transducer type

    DEFF Research Database (Denmark)

    Wilhjelm, Jens E.; Pedersen, P.C.; Jacobsen, S.M.

    1998-01-01

    The received electrical signal from a pulse-echo system insonifying a planar acoustical interface was measured for varying degrees of rms roughness (0-0.16 mm), angle of incidence (typically +/-7°) and range to the transducer. A planar and a focused 5 MHz transducer was used. When insonifying...... a smooth interface, the normalized spectrum of the received signals for a planar transducer exhibits an increasing number of nulls with increased angle of insonification, as predicted from numerical modeling while the dependence on insonification angle for the focused transducer was smaller and the null...... pattern was much less distinct. For the planar transducer and for the focused transducer with the interface located at the geometrical point of focus, the energy of the received signal as a function of incident angle was approximately Gaussian with maximum at 0°. For the smooth interface, the -3 dB width...

  16. Rough Mirror as a Quantum State Selector: Analysis and Design

    International Nuclear Information System (INIS)

    Nesvizhevsky, V. V.; Lamy, F.; Meyerovich, A. E.; Escobar, M.

    2014-01-01

    We report analysis of rough mirrors used as the gravitational state selectors in neutron beam and similar experiments. The key to mirror properties is its roughness correlation function (CF) which is extracted from the precision optical scanning measurements of the surface profile. To identify CF in the presence of fluctuation-driven fat tails, we perform numerical experiments with computer-generated random surfaces with the known CF. These numerical experiments provide a reliable identification procedure which we apply to the actual rough mirror. The extracted CF allows us to make predictions for ongoing GRANIT experiments. We also propose a radically new design for rough mirrors based on Monte Carlo simulations for the 1D Ising model. The implementation of this design provides a controlled environment with predictable scattering properties

  17. Impact of nighttime paving operations on asphalt roughness behavior.

    Science.gov (United States)

    2013-05-01

    The relationship between nighttime construction scheduling and future road quality in terms of roughness was investigated. Research was three-phased: interviews with local leaders in paving, on-site observations, and historical data analyses. Intervi...

  18. Matroidal Structure of Generalized Rough Sets Based on Tolerance Relations

    Directory of Open Access Journals (Sweden)

    Hui Li

    2014-01-01

    of the generalized rough set based on the tolerance relation. The matroid can also induce a new relation. We investigate the connection between the original tolerance relation and the induced relation.

  19. Turbulent lubrication theory considering the surface roughness effects, 2

    International Nuclear Information System (INIS)

    Hashimoto, Hiromu; Wada, Sanae; Kobayashi, Toshinobu.

    1990-01-01

    This second paper describes an application of the generalized turbulent lubrication theory considering the surface roughness effects, which is developed in the previous paper, to the finite-width journal bearings. In the numerical analysis, the nonlinear equations for the modified turbulence coefficients are simplified to save a computation time within a satisfactory accuracy under the assumption that the shear flow is superior to the pressure flow in the turbulent lubrication films. The numerical results of pressure distribution, Sommerfeld number, attitude angle, friction coefficient and flow rate for the Reynolds number of Re=2000, 5000 and 10000 are indicated in graphic form for various values of relative roughness, and the effects of surface roughness on these static performance characteristics are discussed. Moreover, the eccentricity ratio and attitude angle of the journal bearings with homogeneous rough surface are obtained experimentally for a wide range of Sommerfeld number, and the experimental results are compared with theoretical results. (author)

  20. Rough-wall turbulent boundary layers with constant skin friction

    KAUST Repository

    Sridhar, A.; Pullin, D. I.; Cheng, W.

    2017-01-01

    A semi-empirical model is presented that describes the development of a fully developed turbulent boundary layer in the presence of surface roughness with length scale ks that varies with streamwise distance x . Interest is centred on flows

  1. Study of the relationship between non-dimensional roughness ...

    Indian Academy of Sciences (India)

    R. Narasimhan (Krishtel eMaging) 1461 1996 Oct 15 13:05:22

    4National Research Institute for Earth Science and Disaster Prevention,. Science and Technology .... trum S(f,θ) is commonly expressed as the product ..... rough flow must be satisfied according to Toba et al. (1990). ... development; J. Phys.

  2. Optimization of surface roughness in CNC end milling using ...

    African Journals Online (AJOL)

    International Journal of Engineering, Science and Technology ... In this study, minimization of surface roughness has been investigated by integrating design of experiment method, Response surface methodology (RSM) and genetic algorithm ...

  3. The Simulation Realization of Pavement Roughness in the Time Domain

    Science.gov (United States)

    XU, H. L.; He, L.; An, D.

    2017-10-01

    As the needs for the dynamic study on the vehicle-pavement system and the simulated vibration table test, how to simulate the pavement roughness actually is important guarantee for whether calculation and test can reflect the actual situation or not. Using the power spectral density function, the simulation of pavement roughness can be realized by Fourier inverse transform. The main idea of this method was that the spectrum amplitude and random phase were obtained separately according to the power spectrum, and then the simulation of pavement roughness was obtained in the time domain through the Fourier inverse transform (IFFT). In the process, the sampling interval (Δl) was 0.1m, and the sampling points(N) was 4096, which satisfied the accuracy requirements. Using this method, the simulate results of pavement roughness (A~H grades) were obtain in the time domain.

  4. Empirical model for estimating the surface roughness of machined ...

    African Journals Online (AJOL)

    Empirical model for estimating the surface roughness of machined ... as well as surface finish is one of the most critical quality measure in mechanical products. ... various cutting speed have been developed using regression analysis software.

  5. Scattering of Rossby and Poincare waves off rough lateral boundaries

    Digital Repository Service at National Institute of Oceanography (India)

    Fernandes, A.A; Prahalad, Y.S.; Sengupta, D.

    Unified treatment of wave scattering from a rough boundary, which was originally developed by Nakayama et al. is presented. The stationary nature of the boundary process is used to show that the wave field is also stationary, and therefore can...

  6. Empirical model for estimating the surface roughness of machined ...

    African Journals Online (AJOL)

    Michael Horsfall

    one of the most critical quality measure in mechanical products. In the ... Keywords: cutting speed, centre lathe, empirical model, surface roughness, Mean absolute percentage deviation ... The factors considered were work piece properties.

  7. Fatal pox infection in a rough-legged hawk

    Science.gov (United States)

    Pearson, G.L.; Pass, D.A.; Beggs, E.C.

    1975-01-01

    Natural pox infection occurred in a free-living rough-legged hawk (Buteo lagopus) in northeastern North Dakota. Gross, histological and electron microscopic findings were typical of pox infection, and characteristic lesions developed in red-tailed hawks (Buteo jamaicensis) but not in great horned owls (Bubo virginianus) following inoculation with case material. Death of the rough-legged hawk was attributed to starvation resulting from inability to capture prey and to blood loss from foot lesions.

  8. Consideration of pavement roughness effects on vehicle-pavement interaction

    CSIR Research Space (South Africa)

    Steyn, WJvdM

    2001-07-01

    Full Text Available . In this paper the focus is on quantification of the pavement roughness effects on the calculated structural pavement life and the effects of surfacing maintenance on the moving dynamic tyre loads generated by vehicles. A simplified method for calculating... the moving dynamic tyre load population is used together with standard pavement response analysis methods to quantify the effects of pavement surfacing maintenance on roughness and structural pavement life. This method can be used as a pavement management...

  9. Purity and surface roughness of vacuum deposited aluminium films

    Energy Technology Data Exchange (ETDEWEB)

    Dhere, N G; Arsenio, T P [Instituto Militar de Engenharia, Rio de Janeiro (Brazil); Patnaik, B K [Pontificia Universidade Catolica do Rio de Janeiro (Brazil). Instituto de Fisica; Assuncao, F C.R.; de Souza, A M [Pontificia Universidade Catolica do Rio de Janeiro (Brazil). Departamento de Ciencia dos Materiais e Metalurgia

    1975-04-01

    The authors studied the purity, surface roughness and grain size of vacuum-deposited aluminium films, using an intermetallic crucible and a continuous feed of pure aluminium wire. The grain size and roughness were studied by electron difraction, X-ray diffraction and the scanning electron microscope. Purity was determined by X-ray fluorescence produced by proton bombardment in the Van de Graaff accelerator and by X-ray and optical emission spectrometry.

  10. ANFIS Modeling of the Surface Roughness in Grinding Process

    OpenAIRE

    H. Baseri; G. Alinejad

    2011-01-01

    The objective of this study is to design an adaptive neuro-fuzzy inference system (ANFIS) for estimation of surface roughness in grinding process. The Used data have been generated from experimental observations when the wheel has been dressed using a rotary diamond disc dresser. The input parameters of model are dressing speed ratio, dressing depth and dresser cross-feed rate and output parameter is surface roughness. In the experimental procedure the grinding conditions...

  11. Surface roughness influences on the behaviour of flow inside microchannels

    Science.gov (United States)

    Farias, M. H.; Castro, C. S.; Garcia, D. A.; Henrique, J. S.

    2018-03-01

    This work discusses influence of the surface roughness on the behavior of liquids flowing inside microchannels. By measuring the flow profile using the micro-PIV technique, the flow of water inside two rectangular microchannels of different wall roughness and in a circular smooth microchannel was studied. Comparisons were made among the experimental results, showing that a metrological approach concerning surface characteristics of microdevices is required to ensure reliability of the measurements for flow analyses in microfluidic processes.

  12. The surface roughness effect on the performance of supersonic ejectors

    Science.gov (United States)

    Brezgin, D. V.; Aronson, K. E.; Mazzelli, F.; Milazzo, A.

    2017-07-01

    The paper presents the numerical simulation results of the surface roughness influence on gas-dynamic processes inside flow parts of a supersonic ejector. These simulations are performed using two commercial CFD solvers (Star- CCM+ and Fluent). The results are compared to each other and verified by a full-scale experiment in terms of global flow parameters (the entrainment ratio: the ratio between secondary to primary mass flow rate - ER hereafter) and local flow parameters distribution (the static pressure distribution along the mixing chamber and diffuser walls). A detailed comparative study of the employed methods and approaches in both CFD packages is carried out in order to estimate the roughness effect on the logarithmic law velocity distribution inside the boundary layer. Influence of the surface roughness is compared with the influence of the backpressure (static pressure at the ejector outlet). It has been found out that increasing either the ejector backpressure or the surface roughness height, the shock position displaces upstream. Moreover, the numerical simulation results of an ejector with rough walls in the both CFD solvers are well quantitatively agreed with each other in terms of the mean ER and well qualitatively agree in terms of the local flow parameters distribution. It is found out that in the case of exceeding the "critical roughness height" for the given boundary conditions and ejector's geometry, the ejector switches to the "off-design" mode and its performance decreases considerably.

  13. The influence of roughness and obstacle on wind power map

    International Nuclear Information System (INIS)

    Abas Ab Wahab; Mohd Fadhil Abas; Mohd Hafiz Ismail

    2006-01-01

    In the development of wind energy in Malaysia, the need for wind power map of Peninsular Malaysia has aroused. The map is needed to help in determining the potential areas where low wind speed wind turbines could operate optimally. In establishing the wind power map the effects of roughness and obstacles have been investigated. Wind data from 24 meteorological stations around the country have been utilized in conjunction with the respective local roughness and obstacles. Two sets of wind power maps have been developed i.e. the wind power maps with and without roughness and obstacles. These two sets of wind power maps exhibit great significant amount of difference in the wind power values especially in the inland areas where the wind power map without roughness and obstacles gives much lower values than those with roughness and obstacles. This paper outlines the process of establishing the two sets of wind power map as well as discussing the influence of roughness and obstacles based on the results obtained

  14. AN AUTOMATED ROAD ROUGHNESS DETECTION FROM MOBILE LASER SCANNING DATA

    Directory of Open Access Journals (Sweden)

    P. Kumar

    2017-05-01

    Full Text Available Rough roads influence the safety of the road users as accident rate increases with increasing unevenness of the road surface. Road roughness regions are required to be efficiently detected and located in order to ensure their maintenance. Mobile Laser Scanning (MLS systems provide a rapid and cost-effective alternative by providing accurate and dense point cloud data along route corridor. In this paper, an automated algorithm is presented for detecting road roughness from MLS data. The presented algorithm is based on interpolating smooth intensity raster surface from LiDAR point cloud data using point thinning process. The interpolated surface is further processed using morphological and multi-level Otsu thresholding operations to identify candidate road roughness regions. The candidate regions are finally filtered based on spatial density and standard deviation of elevation criteria to detect the roughness along the road surface. The test results of road roughness detection algorithm on two road sections are presented. The developed approach can be used to provide comprehensive information to road authorities in order to schedule maintenance and ensure maximum safety conditions for road users.

  15. An Automated Road Roughness Detection from Mobile Laser Scanning Data

    Science.gov (United States)

    Kumar, P.; Angelats, E.

    2017-05-01

    Rough roads influence the safety of the road users as accident rate increases with increasing unevenness of the road surface. Road roughness regions are required to be efficiently detected and located in order to ensure their maintenance. Mobile Laser Scanning (MLS) systems provide a rapid and cost-effective alternative by providing accurate and dense point cloud data along route corridor. In this paper, an automated algorithm is presented for detecting road roughness from MLS data. The presented algorithm is based on interpolating smooth intensity raster surface from LiDAR point cloud data using point thinning process. The interpolated surface is further processed using morphological and multi-level Otsu thresholding operations to identify candidate road roughness regions. The candidate regions are finally filtered based on spatial density and standard deviation of elevation criteria to detect the roughness along the road surface. The test results of road roughness detection algorithm on two road sections are presented. The developed approach can be used to provide comprehensive information to road authorities in order to schedule maintenance and ensure maximum safety conditions for road users.

  16. Simple model of surface roughness for binary collision sputtering simulations

    Energy Technology Data Exchange (ETDEWEB)

    Lindsey, Sloan J. [Institute of Solid-State Electronics, TU Wien, Floragasse 7, A-1040 Wien (Austria); Hobler, Gerhard, E-mail: gerhard.hobler@tuwien.ac.at [Institute of Solid-State Electronics, TU Wien, Floragasse 7, A-1040 Wien (Austria); Maciążek, Dawid; Postawa, Zbigniew [Institute of Physics, Jagiellonian University, ul. Lojasiewicza 11, 30348 Kraków (Poland)

    2017-02-15

    Highlights: • A simple model of surface roughness is proposed. • Its key feature is a linearly varying target density at the surface. • The model can be used in 1D/2D/3D Monte Carlo binary collision simulations. • The model fits well experimental glancing incidence sputtering yield data. - Abstract: It has been shown that surface roughness can strongly influence the sputtering yield – especially at glancing incidence angles where the inclusion of surface roughness leads to an increase in sputtering yields. In this work, we propose a simple one-parameter model (the “density gradient model”) which imitates surface roughness effects. In the model, the target’s atomic density is assumed to vary linearly between the actual material density and zero. The layer width is the sole model parameter. The model has been implemented in the binary collision simulator IMSIL and has been evaluated against various geometric surface models for 5 keV Ga ions impinging an amorphous Si target. To aid the construction of a realistic rough surface topography, we have performed MD simulations of sequential 5 keV Ga impacts on an initially crystalline Si target. We show that our new model effectively reproduces the sputtering yield, with only minor variations in the energy and angular distributions of sputtered particles. The success of the density gradient model is attributed to a reduction of the reflection coefficient – leading to increased sputtering yields, similar in effect to surface roughness.

  17. Near-field flow structures about subcritical surface roughness

    Science.gov (United States)

    Doolittle, Charles J.; Drews, Scott D.; Goldstein, David B.

    2014-12-01

    Laminar flow over a periodic array of cylindrical surface roughness elements is simulated with an immersed boundary spectral method both to validate the method for subsequent studies and to examine how persistent streamwise vortices are introduced by a low Reynolds number roughness element. Direct comparisons are made with prior studies at a roughness-based Reynolds number Rek (=U(k) k/ν) of 205 and a diameter to spanwise spacing ratio d/λ of 1/3. Downstream velocity contours match present and past experiments very well. The shear layer developed over the top of the roughness element produces the downstream velocity deficit. Upstream of the roughness element, the vortex topology is found to be consistent with juncture flow experiments, creating three cores along the recirculation line. Streamtraces stemming from these upstream cores, however, have unexpectedly little effect on the downstream flowfield as lateral divergence of the boundary layer quickly dissipates their vorticity. Long physical relaxation time of the recirculating wake behind the roughness remains a prominent issue for simulating this type of flowfield.

  18. Rheological State Diagrams for Rough Colloids in Shear Flow

    Science.gov (United States)

    Hsiao, Lilian C.; Jamali, Safa; Glynos, Emmanouil; Green, Peter F.; Larson, Ronald G.; Solomon, Michael J.

    2017-10-01

    To assess the role of particle roughness in the rheological phenomena of concentrated colloidal suspensions, we develop model colloids with varying surface roughness length scales up to 10% of the particle radius. Increasing surface roughness shifts the onset of both shear thickening and dilatancy towards lower volume fractions and critical stresses. Experimental data are supported by computer simulations of spherical colloids with adjustable friction coefficients, demonstrating that a reduction in the onset stress of thickening and a sign change in the first normal stresses occur when friction competes with lubrication. In the quasi-Newtonian flow regime, roughness increases the effective packing fraction of colloids. As the shear stress increases and suspensions of rough colloids approach jamming, the first normal stresses switch signs and the critical force required to generate contacts is drastically reduced. This is likely a signature of the lubrication films giving way to roughness-induced tangential interactions that bring about load-bearing contacts in the compression axis of flow.

  19. Simple model of surface roughness for binary collision sputtering simulations

    International Nuclear Information System (INIS)

    Lindsey, Sloan J.; Hobler, Gerhard; Maciążek, Dawid; Postawa, Zbigniew

    2017-01-01

    Highlights: • A simple model of surface roughness is proposed. • Its key feature is a linearly varying target density at the surface. • The model can be used in 1D/2D/3D Monte Carlo binary collision simulations. • The model fits well experimental glancing incidence sputtering yield data. - Abstract: It has been shown that surface roughness can strongly influence the sputtering yield – especially at glancing incidence angles where the inclusion of surface roughness leads to an increase in sputtering yields. In this work, we propose a simple one-parameter model (the “density gradient model”) which imitates surface roughness effects. In the model, the target’s atomic density is assumed to vary linearly between the actual material density and zero. The layer width is the sole model parameter. The model has been implemented in the binary collision simulator IMSIL and has been evaluated against various geometric surface models for 5 keV Ga ions impinging an amorphous Si target. To aid the construction of a realistic rough surface topography, we have performed MD simulations of sequential 5 keV Ga impacts on an initially crystalline Si target. We show that our new model effectively reproduces the sputtering yield, with only minor variations in the energy and angular distributions of sputtered particles. The success of the density gradient model is attributed to a reduction of the reflection coefficient – leading to increased sputtering yields, similar in effect to surface roughness.

  20. A rough multi-factor model of electricity spot prices

    International Nuclear Information System (INIS)

    Bennedsen, Mikkel

    2017-01-01

    We introduce a new continuous-time mathematical model of electricity spot prices which accounts for the most important stylized facts of these time series: seasonality, spikes, stochastic volatility, and mean reversion. Empirical studies have found a possible fifth stylized fact, roughness, and our approach explicitly incorporates this into the model of the prices. Our setup generalizes the popular Ornstein–Uhlenbeck-based multi-factor framework of and allows us to perform statistical tests to distinguish between an Ornstein–Uhlenbeck-based model and a rough model. Further, through the multi-factor approach we account for seasonality and spikes before estimating – and making inference on – the degree of roughness. This is novel in the literature and we present simulation evidence showing that these precautions are crucial for accurate estimation. Lastly, we estimate our model on recent data from six European energy exchanges and find statistical evidence of roughness in five out of six markets. As an application of our model, we show how, in these five markets, a rough component improves short term forecasting of the prices. - Highlights: • Statistical modeling of electricity spot prices • Multi-factor decomposition • Roughness • Electricity price forecasting

  1. Gliding swifts attain laminar flow over rough wings.

    Directory of Open Access Journals (Sweden)

    David Lentink

    Full Text Available Swifts are among the most aerodynamically refined gliding birds. However, the overlapping vanes and protruding shafts of their primary feathers make swift wings remarkably rough for their size. Wing roughness height is 1-2% of chord length on the upper surface--10,000 times rougher than sailplane wings. Sailplanes depend on extreme wing smoothness to increase the area of laminar flow on the wing surface and minimize drag for extended glides. To understand why the swift does not rely on smooth wings, we used a stethoscope to map laminar flow over preserved wings in a low-turbulence wind tunnel. By combining laminar area, lift, and drag measurements, we show that average area of laminar flow on swift wings is 69% (n = 3; std 13% of their total area during glides that maximize flight distance and duration--similar to high-performance sailplanes. Our aerodynamic analysis indicates that swifts attain laminar flow over their rough wings because their wing size is comparable to the distance the air travels (after a roughness-induced perturbation before it transitions from laminar to turbulent. To interpret the function of swift wing roughness, we simulated its effect on smooth model wings using physical models. This manipulation shows that laminar flow is reduced and drag increased at high speeds. At the speeds at which swifts cruise, however, swift-like roughness prolongs laminar flow and reduces drag. This feature gives small birds with rudimentary wings an edge during the evolution of glide performance.

  2. Electrotunable lubricity with ionic liquids: the influence of nanoscale roughness.

    Science.gov (United States)

    David, Alessio; Fajardo, Oscar Y; Kornyshev, Alexei A; Urbakh, Michael; Bresme, Fernando

    2017-07-01

    The properties of ionic liquids can be modified by applying an external electrostatic potential, providing a route to control their performance in nanolubrication applications. Most computational studies to date have focused on the investigation of smooth surfaces. Real surfaces are generally inhomogeneous and feature roughness of different length scales. We report here a study of the possible effects that surface roughness may have on electrotunable lubricity with ionic liquids, performed here by means of non-equilibrium molecular dynamics simulations. In order to advance our understanding of the interplay of friction and substrate structure we investigate coarse grained models of ionic liquids confined in model surfaces with nanometer roughness. The friction is shown to depend on the roughness of the substrate and the direction of shear. For the investigated systems, the friction coefficient is found to increase with roughness. These results are in contrast with previous studies, where roughness induced reduction of friction was reported, and they highlight the strong sensitivity of the friction process to the structure of the surfaces. The friction force features a maximum at a specific surface charge density. This behaviour is reminiscent of the one reported in ionic liquids confined by flat surfaces, showing the generality of this physical effect in confined ionic liquids. We find that an increase of the substrate-liquid dispersion interactions shifts the maximum to lower surface charges. This effect opens a route to control electrotunable friction phenomena by tuning both the electrostatic potential and the composition of the confining surfaces.

  3. Study the Relationship between Pavement Surface Distress and Roughness Data

    Directory of Open Access Journals (Sweden)

    Mubaraki Muhammad

    2016-01-01

    Full Text Available In this paper, pavement sections from the highway connected Jeddah to Jazan were selected and analyzed to investigate the relationship between International Roughness Index (IRI and pavement damage including; cracking, rutting, and raveling. The Ministry of Transport (MOT of Saudi Arabia has been collecting pavement condition data using the Road Surface Tester (RST vehicle. The MOT measures Roughness, Rutting (RUT, Cracking (CRA, raveling (RAV. Roughness measurements are calculated in terms of the International Roughness Index (IRI. The IRI is calculated over equally spaced intervals along the road profile. Roughness measurements are performed at speed between at 80 kilometers per hour. Thus RST vehicle has been used to evaluate highways across the country. The paper shows three relationships including; cracking (CRA verses roughness (IRI, rutting (RUT verses IRI, and raveling (RAV verses IRI. Also, the paper developed two models namely; model relates IRI to the three distress under study, and model relates IRI to ride quality. The results of the analysis claim at 95% confidence that a significant relationship exist between IRI and cracking, and raveling. It’s also shown that rutting did not show significant relationship to IRI values. That’s leads to conclude that the distresses types: cracking and raveling may possibly be described as ride quality distresses at different level of significant. Rutting distress described as non-ride quality type’s distresses.

  4. Rheological State Diagrams for Rough Colloids in Shear Flow.

    Science.gov (United States)

    Hsiao, Lilian C; Jamali, Safa; Glynos, Emmanouil; Green, Peter F; Larson, Ronald G; Solomon, Michael J

    2017-10-13

    To assess the role of particle roughness in the rheological phenomena of concentrated colloidal suspensions, we develop model colloids with varying surface roughness length scales up to 10% of the particle radius. Increasing surface roughness shifts the onset of both shear thickening and dilatancy towards lower volume fractions and critical stresses. Experimental data are supported by computer simulations of spherical colloids with adjustable friction coefficients, demonstrating that a reduction in the onset stress of thickening and a sign change in the first normal stresses occur when friction competes with lubrication. In the quasi-Newtonian flow regime, roughness increases the effective packing fraction of colloids. As the shear stress increases and suspensions of rough colloids approach jamming, the first normal stresses switch signs and the critical force required to generate contacts is drastically reduced. This is likely a signature of the lubrication films giving way to roughness-induced tangential interactions that bring about load-bearing contacts in the compression axis of flow.

  5. Multipoint contact modeling of nanoparticle manipulation on rough surface

    Energy Technology Data Exchange (ETDEWEB)

    Zakeri, M., E-mail: m.zakeri@tabrizu.ac.ir; Faraji, J.; Kharazmi, M. [University of Tabriz, School of Engineering Emerging Technologies (Iran, Islamic Republic of)

    2016-12-15

    In this paper, the atomic force microscopy (AFM)-based 2-D pushing of nano/microparticles investigated on rough substrate by assuming a multipoint contact model. First, a new contact model was extracted and presented based on the geometrical profiles of Rumpf, Rabinovich and George models and the contact mechanics theories of JKR and Schwartz, to model the adhesion forces and the deformations in the multipoint contact of rough surfaces. The geometry of a rough surface was defined by two main parameters of asperity height (size of roughness) and asperity wavelength (compactness of asperities distribution). Then, the dynamic behaviors of nano/microparticles with radiuses in range of 50–500 nm studied during their pushing on rough substrate with a hexagonal or square arrangement of asperities. Dynamic behavior of particles were simulated and compared by assuming multipoint and single-point contact schemes. The simulation results show that the assumption of multipoint contact has a considerable influence on determining the critical manipulation force. Additionally, the assumption of smooth surfaces or single-point contact leads to large error in the obtained results. According to the results of previous research, it anticipated that a particles with the radius less than about 550 nm start to slide on smooth substrate; but by using multipoint contact model, the predicted behavior changed, and particles with radii of smaller than 400 nm begin to slide on rough substrate for different height of asperities, at first.

  6. Mapping gullies, dunes, lava fields, and landslides via surface roughness

    Science.gov (United States)

    Korzeniowska, Karolina; Pfeifer, Norbert; Landtwing, Stephan

    2018-01-01

    Gully erosion is a widespread and significant process involved in soil and land degradation. Mapping gullies helps to quantify past, and anticipate future, soil losses. Digital terrain models offer promising data for automatically detecting and mapping gullies especially in vegetated areas, although methods vary widely measures of local terrain roughness are the most varied and debated among these methods. Rarely do studies test the performance of roughness metrics for mapping gullies, limiting their applicability to small training areas. To this end, we systematically explored how local terrain roughness derived from high-resolution Light Detection And Ranging (LiDAR) data can aid in the unsupervised detection of gullies over a large area. We also tested expanding this method for other landforms diagnostic of similarly abrupt land-surface changes, including lava fields, dunes, and landslides, as well as investigating the influence of different roughness thresholds, resolutions of kernels, and input data resolution, and comparing our method with previously published roughness algorithms. Our results show that total curvature is a suitable metric for recognising analysed gullies and lava fields from LiDAR data, with comparable success to that of more sophisticated roughness metrics. Tested dunes or landslides remain difficult to distinguish from the surrounding landscape, partly because they are not easily defined in terms of their topographic signature.

  7. Comparison of optical methods for surface roughness characterization

    International Nuclear Information System (INIS)

    Feidenhans’l, Nikolaj A; Hansen, Poul-Erik; Madsen, Morten H; Petersen, Jan C; Pilný, Lukáš; Bissacco, Giuliano; Taboryski, Rafael

    2015-01-01

    We report a study of the correlation between three optical methods for characterizing surface roughness: a laboratory scatterometer measuring the bi-directional reflection distribution function (BRDF instrument), a simple commercial scatterometer (rBRDF instrument), and a confocal optical profiler. For each instrument, the effective range of spatial surface wavelengths is determined, and the common bandwidth used when comparing the evaluated roughness parameters. The compared roughness parameters are: the root-mean-square (RMS) profile deviation (Rq), the RMS profile slope (Rdq), and the variance of the scattering angle distribution (Aq). The twenty-two investigated samples were manufactured with several methods in order to obtain a suitable diversity of roughness patterns.Our study shows a one-to-one correlation of both the Rq and the Rdq roughness values when obtained with the BRDF and the confocal instruments, if the common bandwidth is applied. Likewise, a correlation is observed when determining the Aq value with the BRDF and the rBRDF instruments.Furthermore, we show that it is possible to determine the Rq value from the Aq value, by applying a simple transfer function derived from the instrument comparisons. The presented method is validated for surfaces with predominantly 1D roughness, i.e. consisting of parallel grooves of various periods, and a reflectance similar to stainless steel. The Rq values are predicted with an accuracy of 38% at the 95% confidence interval. (paper)

  8. When the going gets rough – studying the effect of surface roughness on the adhesive abilities of tree frogs

    Directory of Open Access Journals (Sweden)

    Niall Crawford

    2016-12-01

    Full Text Available Tree frogs need to adhere to surfaces of various roughnesses in their natural habitats; these include bark, leaves and rocks. Rough surfaces can alter the effectiveness of their toe pads, due to factors such as a change of real contact area and abrasion of the pad epithelium. Here, we tested the effect of surface roughness on the attachment abilities of the tree frog Litoria caerulea. This was done by testing shear and adhesive forces on artificial surfaces with controlled roughness, both on single toe pads and whole animal scales. It was shown that frogs can stick 2–3 times better on small scale roughnesses (3–6 µm asperities, producing higher adhesive and frictional forces, but relatively poorly on the larger scale roughnesses tested (58.5–562.5 µm asperities. Our experiments suggested that, on such surfaces, the pads secrete insufficient fluid to fill the space under the pad, leaving air pockets that would significantly reduce the Laplace pressure component of capillarity. Therefore, we measured how well the adhesive toe pad would conform to spherical asperities of known sizes using interference reflection microscopy. Based on experiments where the conformation of the pad to individual asperities was examined microscopically, our calculations indicate that the pad epithelium has a low elastic modulus, making it highly deformable.

  9. The effect of roughness, floor polish, water, oil and ice on underfoot friction: current safety footwear solings are less slip resistant than microcellular polyurethane.

    Science.gov (United States)

    Manning, D P; Jones, C

    2001-04-01

    Research over a period of about 18 years has shown that a microcellular polyurethane known as AP66033 is the most slip-resistant safety footwear soling material on oily and wet surfaces. In recent years it has been replaced in commercially available footwear by a dual density polyurethane (DDP) which has a dense outer layer and a soft microcellular backing. This research programme has compared the slip resistance of AP66033 with DDP and some rubber solings. In addition, data were obtained on the effects of soling and floor roughness, and floor polish on slip resistance. Some data were also obtained for walking on ice. The coefficient of friction (CoF) of the solings was measured on 19 water wet surfaces in three conditions: (I) when the solings were new, (II) following abrasion to create maximum roughness and (III) after polishing. The CoF was measured on four oily surfaces after each of 11 abrasion or polishing treatments. The profound effects of the roughening of all soles and of floor roughness on the CoF were demonstrated for both wet and oily surfaces. The superior slip resistance of AP66033 was confirmed for oily and wet conditions; however, some rubbers not suitable for safety footwear achieved higher CoF values on wet floors. All of the floor polishes reduced the CoF of all floors when contaminated with water. The mean CoF of DDP solings was lower than the mean for AP66033 on wet and oily surfaces. No safety footwear soling provided adequate grip on dry ice and the CoF was reduced by water on the ice. A rubber used for rock climbing footwear was one of the most slip-resistant solings on wet surfaces in the laboratory but recorded the lowest CoF on ice. It is concluded that the incidence of occupational injuries caused by slipping could be reduced by the following: (A) returning to safety footwear soled with the microcellular polyurethane AP66033; (B) abrading all new and smooth footwear solings with a belt sanding machine coated with P100 grit; (C) avoiding

  10. Determination of forest road surface roughness by Kinect depth imaging

    Directory of Open Access Journals (Sweden)

    Francesco Marinello

    2017-12-01

    Full Text Available Roughness is a dynamic property of the gravel road surface that affects safety, ride comfort as well as vehicle tyre life and maintenance costs. A rapid survey of gravel road condition is fundamental for an effective maintenance planning and definition of the intervention priorities.Different non-contact techniques such as laser scanning, ultrasonic sensors and photogrammetry have recently been proposed to reconstruct three-dimensional topography of road surface and allow extraction of roughness metrics. The application of Microsoft Kinect™ depth camera is proposed and discussed here for collection of 3D data sets from gravel roads, to be implemented in order to allow quantification of surface roughness.The objectives are to: i verify the applicability of the Kinect sensor for characterization of different forest roads, ii identify the appropriateness and potential of different roughness parameters and iii analyse the correlation with vibrations recoded by 3-axis accelerometers installed on different vehicles. The test took advantage of the implementation of the Kinect depth camera for surface roughness determination of 4 different forest gravel roads and one well-maintained asphalt road as reference. Different vehicles (mountain bike, off-road motorcycle, ATV vehicle, 4WD car and compact crossover were included in the experiment in order to verify the vibration intensity when travelling on different road surface conditions. Correlations between the extracted roughness parameters and vibration levels of the tested vehicles were then verified. Coefficients of determination of between 0.76 and 0.97 were detected between average surface roughness and standard deviation of relative accelerations, with higher values in the case of lighter vehicles.

  11. Numerical Modeling of Electrical Contact Conductance of Rough Bodies

    Directory of Open Access Journals (Sweden)

    M. V. Murashov

    2015-01-01

    Full Text Available Since the beginning of the 20th century to the present time, efforts have been made to develop a model of the electrical contact conductance. The development of micro- and nanotechnologies make contact conductance problem more essential. To conduct borrowing from a welldeveloped thermal contact conductance models on the basis of thermal and electrical conductivity analogy is often not possible due to a number of fundamental differences. While some 3Dmodels of rough bodies deformation have been developed in one way or another, a 3D-model of the electrical conductance through rough bodies contact is still not. A spatial model of electrical contact of rough bodies is proposed, allows one to calculate the electrical contact conductance as a function of the contact pressure. Representative elements of the bodies are parallelepipeds with deterministic roughness on the contacting surfaces. First the non-linear elastic-plastic deformation of rough surface under external pressure is solved using the finite element software ANSYS. Then the solution of electrostatic problem goes on the same finite element mesh. Aluminum AD1 is used as the material of the contacting bodies with properties that account for cold work hardening of the surface. The numerical model is built within the continuum mechanics and nanoscale effects are not taken into account. The electrical contact conductance was calculated on the basis of the concept of electrical resistance of the model as the sum of the electrical resistances of the contacting bodies and the contact itself. It was assumed that there is no air in the gap between the bodies. The dependence of the electrical contact conductance on the contact pressure is calculated as well as voltage and current density distributions in the contact bodies. It is determined that the multi-asperity contact mode, adequate to real roughness, is achieved at pressures higher than 3MPa, while results within the single contact spot are

  12. Lunar terrain mapping and relative-roughness analysis

    Science.gov (United States)

    Rowan, Lawrence C.; McCauley, John F.; Holm, Esther A.

    1971-01-01

    Terrain maps of the equatorial zone (long 70° E.-70° W. and lat 10° N-10° S.) were prepared at scales of 1:2,000,000 and 1:1,000,000 to classify lunar terrain with respect to roughness and to provide a basis for selecting sites for Surveyor and Apollo landings as well as for Ranger and Lunar Orbiter photographs. The techniques that were developed as a result of this effort can be applied to future planetary exploration. By using the best available earth-based observational data and photographs 1:1,000,000-scale and U.S. Geological Survey lunar geologic maps and U.S. Air Force Aeronautical Chart and Information Center LAC charts, lunar terrain was described by qualitative and quantitative methods and divided into four fundamental classes: maria, terrae, craters, and linear features. Some 35 subdivisions were defined and mapped throughout the equatorial zone, and, in addition, most of the map units were illustrated by photographs. The terrain types were analyzed quantitatively to characterize and order their relative-roughness characteristics. Approximately 150,000 east-west slope measurements made by a photometric technique (photoclinometry) in 51 sample areas indicate that algebraic slope-frequency distributions are Gaussian, and so arithmetic means and standard deviations accurately describe the distribution functions. The algebraic slope-component frequency distributions are particularly useful for rapidly determining relative roughness of terrain. The statistical parameters that best describe relative roughness are the absolute arithmetic mean, the algebraic standard deviation, and the percentage of slope reversal. Statistically derived relative-relief parameters are desirable supplementary measures of relative roughness in the terrae. Extrapolation of relative roughness for the maria was demonstrated using Ranger VII slope-component data and regional maria slope data, as well as the data reported here. It appears that, for some morphologically homogeneous

  13. Unbiased roughness measurements: the key to better etch performance

    Science.gov (United States)

    Liang, Andrew; Mack, Chris; Sirard, Stephen; Liang, Chen-wei; Yang, Liu; Jiang, Justin; Shamma, Nader; Wise, Rich; Yu, Jengyi; Hymes, Diane

    2018-03-01

    Edge placement error (EPE) has become an increasingly critical metric to enable Moore's Law scaling. Stochastic variations, as characterized for lines by line width roughness (LWR) and line edge roughness (LER), are dominant factors in EPE and known to increase with the introduction of EUV lithography. However, despite recommendations from ITRS, NIST, and SEMI standards, the industry has not agreed upon a methodology to quantify these properties. Thus, differing methodologies applied to the same image often result in different roughness measurements and conclusions. To standardize LWR and LER measurements, Fractilia has developed an unbiased measurement that uses a raw unfiltered line scan to subtract out image noise and distortions. By using Fractilia's inverse linescan model (FILM) to guide development, we will highlight the key influences of roughness metrology on plasma-based resist smoothing processes. Test wafers were deposited to represent a 5 nm node EUV logic stack. The patterning stack consists of a core Si target layer with spin-on carbon (SOC) as the hardmask and spin-on glass (SOG) as the cap. Next, these wafers were exposed through an ASML NXE 3350B EUV scanner with an advanced chemically amplified resist (CAR). Afterwards, these wafers were etched through a variety of plasma-based resist smoothing techniques using a Lam Kiyo conductor etch system. Dense line and space patterns on the etched samples were imaged through advanced Hitachi CDSEMs and the LER and LWR were measured through both Fractilia and an industry standard roughness measurement software. By employing Fractilia to guide plasma-based etch development, we demonstrate that Fractilia produces accurate roughness measurements on resist in contrast to an industry standard measurement software. These results highlight the importance of subtracting out SEM image noise to obtain quicker developmental cycle times and lower target layer roughness.

  14. Improvement of Reactor Fuel Element Heat Transfer by Surface Roughness

    International Nuclear Information System (INIS)

    Kjellstroem, B.; Larsson, A.E.

    1967-04-01

    In heat exchangers with a limited surface temperature such as reactor fuel elements, rough heat transfer surfaces may give lower pumping power than smooth. To obtain data for choice of the most advantageous roughness for the superheater elements in the Marviken reactor, measurements were made of heat transfer and pressure drop in an annular channel with a smooth or rough test rod in a smooth adiabatic shroud. 24 different roughness geometries were tested. The results were transformed to rod cluster geometry by the method of W B Hall, and correlated by the friction and heat transfer similarity laws as suggested by D F Dipprey and R H Sabersky with RMS errors of 12.5 % in the friction factor and 8.1 % in the Stanton number. The relation between the Stanton number and the friction factor could be described by a relation of the type suggested by W Nunner, with a mean error of 3.1 % and an RMS error of 11.6 %. Application of the results to fuel element calculations is discussed, and the great gains in economy which can be obtained with rough surfaces are demonstrated by two examples

  15. Progress Towards an LES Wall Model Including Unresolved Roughness

    Science.gov (United States)

    Craft, Kyle; Redman, Andrew; Aikens, Kurt

    2015-11-01

    Wall models used in large eddy simulations (LES) are often based on theories for hydraulically smooth walls. While this is reasonable for many applications, there are also many where the impact of surface roughness is important. A previously developed wall model has been used primarily for jet engine aeroacoustics. However, jet simulations have not accurately captured thick initial shear layers found in some experimental data. This may partly be due to nozzle wall roughness used in the experiments to promote turbulent boundary layers. As a result, the wall model is extended to include the effects of unresolved wall roughness through appropriate alterations to the log-law. The methodology is tested for incompressible flat plate boundary layers with different surface roughness. Correct trends are noted for the impact of surface roughness on the velocity profile. However, velocity deficit profiles and the Reynolds stresses do not collapse as well as expected. Possible reasons for the discrepancies as well as future work will be presented. This work used the Extreme Science and Engineering Discovery Environment (XSEDE), which is supported by National Science Foundation grant number ACI-1053575. Computational resources on TACC Stampede were provided under XSEDE allocation ENG150001.

  16. Time-dependent behavior of rough discontinuities under shearing conditions

    Science.gov (United States)

    Wang, Zhen; Shen, Mingrong; Ding, Wenqi; Jang, Boan; Zhang, Qingzhao

    2018-02-01

    The mechanical properties of rocks are generally controlled by their discontinuities. In this study, the time-dependent behavior of rough artificial joints under shearing conditions was investigated. Based on Barton’s standard profile lines, samples with artificial joint surfaces were prepared and used to conduct the shear and creep tests. The test results showed that the shear strength of discontinuity was linearly related to roughness, and subsequently an empirical equation was established. The long-term strength of discontinuity can be identified using the inflection point of the isocreep-rate curve, and it was linearly related to roughness. Furthermore, the ratio of long-term and instantaneous strength decreased with the increase of roughness. The shear-stiffness coefficient increased with the increase of shear rate, and the influence of shear rate on the shear stiffness coefficient decreased with the decrease of roughness. Further study of the mechanism revealed that these results could be attributed to the different time-dependent behavior of intact and joint rocks.

  17. Improvement of Reactor Fuel Element Heat Transfer by Surface Roughness

    Energy Technology Data Exchange (ETDEWEB)

    Kjellstroem, B; Larsson, A E

    1967-04-15

    In heat exchangers with a limited surface temperature such as reactor fuel elements, rough heat transfer surfaces may give lower pumping power than smooth. To obtain data for choice of the most advantageous roughness for the superheater elements in the Marviken reactor, measurements were made of heat transfer and pressure drop in an annular channel with a smooth or rough test rod in a smooth adiabatic shroud. 24 different roughness geometries were tested. The results were transformed to rod cluster geometry by the method of W B Hall, and correlated by the friction and heat transfer similarity laws as suggested by D F Dipprey and R H Sabersky with RMS errors of 12.5 % in the friction factor and 8.1 % in the Stanton number. The relation between the Stanton number and the friction factor could be described by a relation of the type suggested by W Nunner, with a mean error of 3.1 % and an RMS error of 11.6 %. Application of the results to fuel element calculations is discussed, and the great gains in economy which can be obtained with rough surfaces are demonstrated by two examples.

  18. Simple model of surface roughness for binary collision sputtering simulations

    Science.gov (United States)

    Lindsey, Sloan J.; Hobler, Gerhard; Maciążek, Dawid; Postawa, Zbigniew

    2017-02-01

    It has been shown that surface roughness can strongly influence the sputtering yield - especially at glancing incidence angles where the inclusion of surface roughness leads to an increase in sputtering yields. In this work, we propose a simple one-parameter model (the "density gradient model") which imitates surface roughness effects. In the model, the target's atomic density is assumed to vary linearly between the actual material density and zero. The layer width is the sole model parameter. The model has been implemented in the binary collision simulator IMSIL and has been evaluated against various geometric surface models for 5 keV Ga ions impinging an amorphous Si target. To aid the construction of a realistic rough surface topography, we have performed MD simulations of sequential 5 keV Ga impacts on an initially crystalline Si target. We show that our new model effectively reproduces the sputtering yield, with only minor variations in the energy and angular distributions of sputtered particles. The success of the density gradient model is attributed to a reduction of the reflection coefficient - leading to increased sputtering yields, similar in effect to surface roughness.

  19. Investigation and modelling of rubber stationary friction on rough surfaces

    International Nuclear Information System (INIS)

    Le Gal, A; Klueppel, M

    2008-01-01

    This paper presents novel aspects regarding the physically motivated modelling of rubber stationary sliding friction on rough surfaces. The description of dynamic contact is treated within the framework of a generalized Greenwood-Williamson theory for rigid/soft frictional pairings. Due to the self-affinity of rough surfaces, both hysteresis and adhesion friction components arise from a multi-scale excitation of surface roughness. Beside a complete analytical formulation of contact parameters, the morphology of macrotexture is considered via the introduction of a second scaling range at large length scales which mostly contribute to hysteresis friction. Moreover, adhesion friction is related to the real area of contact combined with the kinetics of interfacial peeling effects. Friction experiments carried out with different rubbers on rough granite and asphalt point out the relevance of hysteresis and adhesion friction concepts on rough surfaces. The two scaling ranges approach significantly improves the description of wet and dry friction behaviour within the range of low sliding velocity. In addition, material and surface effects are predicted and understood on a physical basis. The applicability of such modelling is of high interest for materials developers and road constructors regarding the prediction of wet grip performance of tyres on road tracks

  20. Fuzzy Linguistic Optimization on Surface Roughness for CNC Turning

    Directory of Open Access Journals (Sweden)

    Tian-Syung Lan

    2010-01-01

    Full Text Available Surface roughness is often considered the main purpose in contemporary computer numerical controlled (CNC machining industry. Most existing optimization researches for CNC finish turning were either accomplished within certain manufacturing circumstances or achieved through numerous equipment operations. Therefore, a general deduction optimization scheme is deemed to be necessary for the industry. In this paper, the cutting depth, feed rate, speed, and tool nose runoff with low, medium, and high level are considered to optimize the surface roughness for finish turning based on L9(34 orthogonal array. Additionally, nine fuzzy control rules using triangle membership function with respective to five linguistic grades for surface roughness are constructed. Considering four input and twenty output intervals, the defuzzification using center of gravity is then completed. Thus, the optimum general fuzzy linguistic parameters can then be received. The confirmation experiment result showed that the surface roughness from the fuzzy linguistic optimization parameters is significantly advanced compared to that from the benchmark. This paper certainly proposes a general optimization scheme using orthogonal array fuzzy linguistic approach to the surface roughness for CNC turning with profound insight.

  1. Roughness analysis of graphite surfaces of casting elements

    Directory of Open Access Journals (Sweden)

    M. Wieczorowski

    2010-01-01

    Full Text Available In the paper profilometric measurements of graphite casting elements were described. Basic topics necessary to assess roughness of their surfaces and influence of asperities on various properties related to manufacturing and use were discussed. Stylus profilometer technique of surface irregularities measurements including its limits resulting from pickup geometry and its contact with measured object were ana-lyzed. Working principle of tactile profilometer and phenomena taking place during movement of a probe on a measured surface were shown. One of the important aspects is a flight phenomenon, which means movement of a pickup without contact with a surface during inspection resulting from too high scanning speed. results of comparison research for graphite elements of new and used mould and pin composing a set were presented. Using some surface roughness, waviness and primary profile parameters (arithmetical mean of roughness profile heights Ra, biggest roughness profile height Rz, maximum primary profile height Pt as well as maximum waviness profile height Wt a possibility of using surface asperities parameters as a measure of wear of chill graphite elements was proved. The most often applied parameter is Ra, but with a help of parameters from W and P family it was shown, that big changes occur not only for roughness but also for other components of surface irregularities.

  2. Investigation and modelling of rubber stationary friction on rough surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Le Gal, A; Klueppel, M [Deutsches Institut fuer Kautschuktechnologie, Eupener Strasse 33, D-30519 Hannover (Germany)

    2008-01-09

    This paper presents novel aspects regarding the physically motivated modelling of rubber stationary sliding friction on rough surfaces. The description of dynamic contact is treated within the framework of a generalized Greenwood-Williamson theory for rigid/soft frictional pairings. Due to the self-affinity of rough surfaces, both hysteresis and adhesion friction components arise from a multi-scale excitation of surface roughness. Beside a complete analytical formulation of contact parameters, the morphology of macrotexture is considered via the introduction of a second scaling range at large length scales which mostly contribute to hysteresis friction. Moreover, adhesion friction is related to the real area of contact combined with the kinetics of interfacial peeling effects. Friction experiments carried out with different rubbers on rough granite and asphalt point out the relevance of hysteresis and adhesion friction concepts on rough surfaces. The two scaling ranges approach significantly improves the description of wet and dry friction behaviour within the range of low sliding velocity. In addition, material and surface effects are predicted and understood on a physical basis. The applicability of such modelling is of high interest for materials developers and road constructors regarding the prediction of wet grip performance of tyres on road tracks.

  3. Flu Diagnosis System Using Jaccard Index and Rough Set Approaches

    Science.gov (United States)

    Efendi, Riswan; Azah Samsudin, Noor; Mat Deris, Mustafa; Guan Ting, Yip

    2018-04-01

    Jaccard index and rough set approaches have been frequently implemented in decision support systems with various domain applications. Both approaches are appropriate to be considered for categorical data analysis. This paper presents the applications of sets operations for flu diagnosis systems based on two different approaches, such as, Jaccard index and rough set. These two different approaches are established using set operations concept, namely intersection and subset. The step-by-step procedure is demonstrated from each approach in diagnosing flu system. The similarity and dissimilarity indexes between conditional symptoms and decision are measured using Jaccard approach. Additionally, the rough set is used to build decision support rules. Moreover, the decision support rules are established using redundant data analysis and elimination of unclassified elements. A number data sets is considered to attempt the step-by-step procedure from each approach. The result has shown that rough set can be used to support Jaccard approaches in establishing decision support rules. Additionally, Jaccard index is better approach for investigating the worst condition of patients. While, the definitely and possibly patients with or without flu can be determined using rough set approach. The rules may improve the performance of medical diagnosis systems. Therefore, inexperienced doctors and patients are easier in preliminary flu diagnosis.

  4. Optical measurement of microroughness of pigment coatings on rough substrates

    Science.gov (United States)

    Elton, N. J.

    2009-02-01

    The optical determination of rms roughness at the sub-wavelength scale by measurement of specular intensity as a function of wavelength or angle of incidence is well known. The method is normally used for specimens that are macroscopically flat. However, important industrial materials such as coated paper and paint consist of microscopically rough pigment coatings on a macroscopically rough substrate. Numerical modelling is used to assess the applicability and limitations of optical measurement of microroughness for such materials. Experimental results are presented for a range of paints on substrates of various macroroughness. Model and data are in fair agreement and show that the presence of substrate macroroughness always leads to an underestimation of microroughness. Generally, optical measurements of microroughness are only comparable for substrates of similar macroroughness and a limiting value exists above which measurements may not be meaningful.

  5. Multifrequency passive microwave remote sensing of soil moisture and roughness

    International Nuclear Information System (INIS)

    Paloscia, S.; Pampaloni, P.; Chiarantini, L.; Coppo, P.; Gagliani, S.; Luzi, G.

    1993-01-01

    The accuracy achievable in the surface soil moisture measurement of rough bare and vegetated soils, typical of the Italian landscape, has been investigated by using microwave experimental data collected by means of a multi-band sensor package (L, X, Ka and infrared bands). The thickness of soil that mainly affects the emission at the three microwave frequencies has been assessed. The sensitivity of L band emission to the moisture content of a soil layer about 5 cm thick has been confirmed, as well as the attenuation effect due to the surface roughness and presence of vegetation. A correction criterion based on the sensitivity to roughness and crop parameters of the highest frequencies (X and Ka bands) is proposed in order to increase the precision in soil moisture measurements

  6. Numerical simulation of wall roughness effects in cavitating flow

    Energy Technology Data Exchange (ETDEWEB)

    Echouchene, F. [Laboratoire d' electronique et de microelectronique, Departement de Physique, Faculte des Sciences de Monastir, 5000 (Tunisia); Belmabrouk, H., E-mail: frchouchene@yahoo.fr [Laboratoire d' electronique et de microelectronique, Departement de Physique, Faculte des Sciences de Monastir, 5000 (Tunisia); Le Penven, L.; Buffat, M. [LMFA UMR CNRS 5509, Universite de Claude Bernard Lyon 1, Ecole Centrale de Lyon, INSA de Lyon (France)

    2011-10-15

    Hydrodynamic cavitation has an important effect on the performance of Diesel injectors. It influences the nature of the fuel spray and the efficiency of the combustion process. In the present study, we investigate numerically the effect of wall roughness in the cavitating and turbulent flow developing inside a Diesel injector. The mixture model based on a single fluid is adopted and the commercial Fluent software is used to solve the transport equations. The discharge coefficient C{sub d} is computed for different cavitation numbers and wall roughness heights. Profiles of density mixture, vapor volume fraction, mean velocity and turbulent kinetic energy are reported. The effects of wall roughness and injection pressure are analyzed.

  7. Characterisation of surface roughness for ultra-precision freeform surfaces

    International Nuclear Information System (INIS)

    Li Huifen; Cheung, C F; Lee, W B; To, S; Jiang, X Q

    2005-01-01

    Ultra-precision freeform surfaces are widely used in many advanced optics applications which demand for having surface roughness down to nanometer range. Although a lot of research work has been reported on the study of surface generation, reconstruction and surface characterization such as MOTIF and fractal analysis, most of them are focused on axial symmetric surfaces such as aspheric surfaces. Relative little research work has been found in the characterization of surface roughness in ultra-precision freeform surfaces. In this paper, a novel Robust Gaussian Filtering (RGF) method is proposed for the characterisation of surface roughness for ultra-precision freeform surfaces with known mathematic model or a cloud of discrete points. A series of computer simulation and measurement experiments were conducted to verify the capability of the proposed method. The experimental results were found to agree well with the theoretical results

  8. Scattering from a PEC Slightly Rough Surface in Chiral Media

    Directory of Open Access Journals (Sweden)

    Haroon Akhtar Qureshi

    2018-01-01

    Full Text Available The scattering of left circularly polarized wave from a perfectly electric conducting (PEC rough surface in isotropic chiral media is investigated. Since a slightly rough interface is assumed, the solution is obtained using perturbation method. Zeroth-order term corresponds to solution for a flat interface which helps in making a comparison with the results reported in the literature. First-order term gives the contribution from the surface perturbations, and it is used to define incoherent bistatic scattering coefficients for a Gaussian rough surface. Higher order solution is obtained in a recursive manner. Numerical results are reported for different values of chirality, correlation length, and rms height of the surface. Diffraction efficiency is defined for a sinusoidal grating.

  9. Surface roughness reduction using spray-coated hydrogen silsesquioxane reflow

    DEFF Research Database (Denmark)

    Cech, Jiri; Pranov, Henrik; Kofod, Guggi

    2013-01-01

    Surface roughness or texture is the most visible property of any object, including injection molded plastic parts. Roughness of the injection molding (IM) tool cavity directly affects not only appearance and perception of quality, but often also the function of all manufactured plastic parts. So...... called “optically smooth” plastic surfaces is one example, where low roughness of a tool cavity is desirable. Such tool surfaces can be very expensive to fabricate using conventional means, such as abrasive diamond polishing or diamond turning. We present a novel process to coat machined metal parts...... are reduced 10 and 3 times respectively. We completed more than 10,000 injection molding cycles without detectable degradation of the HSQ coating. This result opens new possibilities for molding of affordable plastic parts with perfect surface finish....

  10. Monitoring tablet surface roughness during the film coating process

    DEFF Research Database (Denmark)

    Seitavuopio, Paulus; Heinämäki, Jyrki; Rantanen, Jukka

    2006-01-01

    The purpose of this study was to evaluate the change of surface roughness and the development of the film during the film coating process using laser profilometer roughness measurements, SEM imaging, and energy dispersive X-ray (EDX) analysis. Surface roughness and texture changes developing during...... the process of film coating tablets were studied by noncontact laser profilometry and scanning electron microscopy (SEM). An EDX analysis was used to monitor the magnesium stearate and titanium dioxide of the tablets. The tablet cores were film coated with aqueous hydroxypropyl methylcellulose, and the film...... coating was performed using an instrumented pilot-scale side-vented drum coater. The SEM images of the film-coated tablets showed that within the first 30 minutes, the surface of the tablet cores was completely covered with a thin film. The magnesium signal that was monitored by SEM-EDX disappeared after...

  11. Qualitative internal surface roughness classification using acoustic emission

    International Nuclear Information System (INIS)

    Mohd Hafizi Zohari; Mohd Hanif Saad

    2009-04-01

    This paper describes a novel new nondestructive method of qualitative internal surface roughness classification for pipes utilizing Acoustic Emission (AE) signal. Two different flowrate are introduced in a pipe obstructed using normally available components (e.g.: valve). The AE signal at suitable location from the obstruction are obtained and the peak amplitudes, RMS amplitude and energy of the AE signal are obtained. A dimensionless number, the Bangi Number, AB, is then calculated as a ratio of the AE parameters (peak amplitude, RMS amplitude or energy) in low flowrate measurement compared to the AE parameters in high flowrate measurement. It was observed that the Bangi Number, AB obtained can then be used to successfully discriminate between rough and smooth internal surface roughness. (author)

  12. Response Ant Colony Optimization of End Milling Surface Roughness

    Directory of Open Access Journals (Sweden)

    Ahmed N. Abd Alla

    2010-03-01

    Full Text Available Metal cutting processes are important due to increased consumer demands for quality metal cutting related products (more precise tolerances and better product surface roughness that has driven the metal cutting industry to continuously improve quality control of metal cutting processes. This paper presents optimum surface roughness by using milling mould aluminium alloys (AA6061-T6 with Response Ant Colony Optimization (RACO. The approach is based on Response Surface Method (RSM and Ant Colony Optimization (ACO. The main objectives to find the optimized parameters and the most dominant variables (cutting speed, feedrate, axial depth and radial depth. The first order model indicates that the feedrate is the most significant factor affecting surface roughness.

  13. THE EFFECT OF OPACIFIERS ON SURFACE ROUGHNESS OFCERAMIC GLAZES

    Directory of Open Access Journals (Sweden)

    R. Sarjahani

    2016-03-01

    Full Text Available Surface smoothness of ceramic glazes is always an important characteristic of ceramic glazes as a point of surface engineering studies. Surface roughness affects chemical resistivity, glossiness and stainabiliy of glazes. In fact, less surface roughness improves cleanability of the surface by the least usage amount of detergents. In this investigation, surface topography of two common opaque glazes, zirconia and titania-based, has been investigated. Crystallinity of the surface has been studied from SEM images, and comparison of EDS elemental results with phase analysis results of XRD. Surface roughness profile measured by Marsurf M300, shows that titania-based glaze is almost 24% percentage more smooth than zirconia based glaze. Surface smoothness is in relation with crystallinity of glaze surface, crystal type and crystal distribution in amorphous matrix phase

  14. Optical measurement of microroughness of pigment coatings on rough substrates

    International Nuclear Information System (INIS)

    Elton, N J

    2009-01-01

    The optical determination of rms roughness at the sub-wavelength scale by measurement of specular intensity as a function of wavelength or angle of incidence is well known. The method is normally used for specimens that are macroscopically flat. However, important industrial materials such as coated paper and paint consist of microscopically rough pigment coatings on a macroscopically rough substrate. Numerical modelling is used to assess the applicability and limitations of optical measurement of microroughness for such materials. Experimental results are presented for a range of paints on substrates of various macroroughness. Model and data are in fair agreement and show that the presence of substrate macroroughness always leads to an underestimation of microroughness. Generally, optical measurements of microroughness are only comparable for substrates of similar macroroughness and a limiting value exists above which measurements may not be meaningful

  15. The effect of sidewall roughness on line edge roughness in top-down scanning electron microscopy images

    Science.gov (United States)

    Verduin, T.; Lokhorst, S. R.; Kruit, P.; Hagen, C. W.

    2015-03-01

    We have investigated in a numerical study the determination of sidewall roughness (SWR) from top down scanning electron microscopy (SEM) images. In a typical metrology application, top-down SEM images are acquired in a (critical-dimension) SEM and the roughness is analyzed. However, the true size, shape and roughness characteristics of resist features are not fully investigated in the analysis of top-down SEM images. In reality, rough resist features are complex three-dimensional structures and the characterization naturally extends to the analysis of SWR. In this study we randomly generate images of rough lines and spaces, where the lines are made of PMMA on a silicon substrate. The lines that we study have a length of 2 µm, a width of 32nm and a height of 32 nm. The SWR is modeled by using the power spectral density (PSD) function of Palasantzas, which characterizes roughness by the standard deviation σ, correlation length ξ and roughness exponent α . The actual roughness is generated by application of the method of Thorsos in two dimensions. The images are constructed by using a home-built program for simulating electron-specimen interactions. The program that we have developed is optimized for complex arbitrary geometries and large number of incident low energy primary electrons by using multi-core CPUs and GPUs. The program uses the dielectric function model for inelastic scattering events and has an implementation specifically for low energy electrons. A satisfactory comparison is made between the secondary electron yields from the home-built program and another program found in literature. In order to reduce the risk of shrinkage, we use a beam energy of 300 eV and a spot size of 3 nm. Each pixel is exposed with 20 electrons on average (≍ 276 µC/cm2), following the Poisson distribution to account for illumination shot noise. We have assumed that the detection of electrons is perfect and does not introduce additional noise. We measure line edge

  16. Goal-Directed Resilience in Training (GRIT: A Biopsychosocial Model of Self-Regulation, Executive Functions, and Personal Growth (Eudaimonia in Evocative Contexts of PTSD, Obesity, and Chronic Pain

    Directory of Open Access Journals (Sweden)

    Martha Kent

    2015-06-01

    Full Text Available This paper presents a biopsychosocial model of self-regulation, executive functions, and personal growth that we have applied to Goal-Directed Resilience in Training (GRIT interventions for posttraumatic stress disorder (PTSD, obesity, and chronic pain. Implications of the training for the prevention of maladaptation, including psychological distress and health declines, and for promoting healthy development are addressed. Existing models of attention, cognition, and physiology were sourced in combination with qualitative study findings in developing this resilience skills intervention. We used qualitative methods to uncover life skills that are most salient in cases of extreme adversity, finding that goal-directed actions that reflected an individual’s values and common humanity with others created a context-independent domain that could compensate for the effects of adversity. The efficacy of the resilience skills intervention for promoting positive emotion, enhancing neurocognitive capacities, and reducing symptoms was investigated in a randomized controlled trial with a veteran population diagnosed with PTSD. The intervention had low attrition (8% and demonstrated improvement on symptom and wellbeing outcomes, indicating that the intervention may be efficacious for PTSD and that it taps into those mechanisms which the intervention was designed to address. Feasibility studies for groups with comorbid diagnoses, such as chronic pain and PTSD, also showed positive results, leading to the application of the GRIT intervention to other evocative contexts such as obesity and chronic pain.

  17. Surface roughness of composite resins subjected to hydrochloric acid.

    Science.gov (United States)

    Roque, Ana Carolina Cabral; Bohner, Lauren Oliveira Lima; de Godoi, Ana Paula Terossi; Colucci, Vivian; Corona, Silmara Aparecida Milori; Catirse, Alma Blásida Concepción Elizaur Benitez

    2015-01-01

    The purpose of this study was to determine the influence of hydrochloric acid on surface roughness of composite resins subjected to brushing. Sixty samples measuring 2 mm thick x 6 mm diameter were prepared and used as experimental units. The study presented a 3x2 factorial design, in which the factors were composite resin (n=20), at 3 levels: microhybrid composite (Z100), nanofilled composite (FiltekTM Supreme), nanohybrid composite (Ice), and acid challenge (n=10) at 2 levels: absence and presence. Acid challenge was performed by immersion of specimens in hydrochloric acid (pH 1.2) for 1 min, 4 times per day for 7 days. The specimens not subjected to acid challenge were stored in 15 mL of artificial saliva at 37 oC. Afterwards, all specimens were submitted to abrasive challenge by a brushing cycle performed with a 200 g weight at a speed of 356 rpm, totaling 17.8 cycles. Surface roughness measurements (Ra) were performed and analyzed by ANOVA and Tukey test (p≤0.05). Surface roughness values were higher in the presence (1.07±0.24) as compared with the absence of hydrochloric acid (0.72±0.04). Surface roughness values were higher for microhybrid (1.01±0.27) compared with nanofilled (0.68 ±0.09) and nanohybrid (0.48±0.15) composites when the specimens were not subjects to acid challenge. In the presence of hydrochloric acid, microhybrid (1.26±0.28) and nanofilled (1.18±0,30) composites presents higher surface roughness values compared with nanohybrid (0.77±0.15). The hydrochloric acid affected the surface roughness of composite resin subjected to brushing.

  18. Helly-type theorems for roughly convexlike sets

    International Nuclear Information System (INIS)

    Phan Thanh An

    2005-04-01

    For a given positive real number of γ, a subset M of an n-dimensional Euclidean space is said to be roughly convexlike (with the roughness degree γ) if x 0 , x 1 is an element of M and parallel x 1 - x 0 parallel > γ imply ]x 0 , x 1 [intersection M ≠ 0. In this paper, we present Helly-type theorems for such sets then solve an open question about sets of constant width raised by Buchman and Valentine and Sallee (author)

  19. Surface roughness of sputtered ZnO films

    Energy Technology Data Exchange (ETDEWEB)

    Lin, Y S [Department of Materials Science and Engineering, National Dong Hwa University, 1, Sec. 2, Da Hsueh Rd. Shou-Feng, Hualien, Taiwan (China); Hsu, K C [Department of Photonics and Institute of Electro-Optical Engineering, National Chiao-Tung University, Hsinchu, Taiwan (China); Huang, Y M [Institute of Electronics Engineering, Southern Taiwan University of Technology, 1 Nan-Tai Street, Taiwan (China)

    2006-09-01

    ZnO films are grown on Si and glass substrates by radio-frequency (RF) magnetron sputtering. The crystalline structures are investigated by x-ray diffraction (XRD). Moreover, the roughness characteristics of the films are examined by atomic force microscopy (AFM) and field-emission scanning electron microscopy (FE-SEM). All films exhibit strong (002) preferential orientation. The influence of the RF power and target-to-substrate distance (D{sub ts}) on the properties of ZnO is studied. Under the optimized conditions of the RF power and D{sub ts}, root-mean-square (RMS) surface roughnesses of <0.8 nm are achieved.

  20. Surface roughness of sputtered ZnO films

    International Nuclear Information System (INIS)

    Lin, Y S; Hsu, K C; Huang, Y M

    2006-01-01

    ZnO films are grown on Si and glass substrates by radio-frequency (RF) magnetron sputtering. The crystalline structures are investigated by x-ray diffraction (XRD). Moreover, the roughness characteristics of the films are examined by atomic force microscopy (AFM) and field-emission scanning electron microscopy (FE-SEM). All films exhibit strong (002) preferential orientation. The influence of the RF power and target-to-substrate distance (D ts ) on the properties of ZnO is studied. Under the optimized conditions of the RF power and D ts , root-mean-square (RMS) surface roughnesses of <0.8 nm are achieved

  1. Additional Smooth and Rough Water Trials of SKI-CAT.

    Science.gov (United States)

    1981-08-01

    REPORT & PERIOD COVERED ADDITIONAL SMOOTH AND ROUGH WATER TRIALS OF FINAL SKI- CAT S. PERFORMING ORO. REPORT NUMSER 7. AUTHOR() I. CONTRACT OR GRANT NUMUr...Identif by bloc membe) ’ " -Further tests of SKI- CAT were made in smooth and rough water. Smooth water results confirmed the performance results of...reductions in the accelerations and motions of SKI- CAT over against the head seasreut DD , +A ,3 1473 EDITION OF I NOVS IS OBSOLETE UNCIbSJFIED SIME 0102-014

  2. Characterization of hypersonic roughness-induced boundary-layer transition

    Science.gov (United States)

    Tirtey, S. C.; Chazot, O.; Walpot, L.

    2011-02-01

    The flow-field structure in the vicinity and in the wake of an isolated 3D roughness element has been studied. Different experimental techniques have been coupled and supported by CFD simulation for a good understanding of the flow-field topology. The results have shown strong flow-field similarities for different roughness elements. A model describing the flow structure and interaction mechanisms has been proposed. This model is in good agreement with experimental and CFD results as well as the literature.

  3. Movements of a Sphere Moving Over Smooth and Rough Inclines

    Science.gov (United States)

    Jan, Chyan-Deng

    1992-01-01

    The steady movements of a sphere over a rough incline in air, and over smooth and rough inclines in a liquid were studied theoretically and experimentally. The principle of energy conservation was used to analyze the translation velocities, rolling resistances, and drag coefficients of a sphere moving over the inclines. The rolling resistance to the movement of a sphere from the rough incline was presumed to be caused by collisions and frictional slidings. A varnished wooden board was placed on the bottom of an experimental tilting flume to form a smooth incline and a layer of spheres identical to the sphere moving over them was placed on the smooth wooden board to form a rough incline. Spheres used in the experiments were glass spheres, steel spheres, and golf balls. Experiments show that a sphere moving over a rough incline with negligible fluid drag in air can reach a constant translation velocity. This constant velocity was found to be proportional to the bed inclination (between 11 ^circ and 21^circ) and the square root of the sphere's diameter, but seemingly independent of the sphere's specific gravity. Two empirical coefficients in the theoretical expression of the sphere's translation velocity were determined by experiments. The collision and friction parts of the shear stress exerted on the interface between the moving sphere and rough incline were determined. The ratio of collision to friction parts appears to increase with increase in the bed inclination. These two parts seem to be of the same order of magnitude. The rolling resistances and the relations between the drag coefficient and Reynolds number for a sphere moving over smooth and rough inclines in a liquid, such as water or salad oil, were determined by a regression analysis based on experimental data. It was found that the drag coefficient for a sphere over the rough incline is larger than that for a sphere over the smooth incline, and both of which are much larger than that for a sphere in free

  4. Influence of roughness parameters on coefficient of friction under ...

    Indian Academy of Sciences (India)

    S¯adhan¯a Vol. 33, Part 3, June 2008, pp. ... Surface texture and thus roughness parameters influence coefficient of friction during sliding. ..... tural irregularities and complexities of the natural system, fractal is widely used to explain the natural ...

  5. Application of function-oriented roughness parameters using confocal microscopy

    Directory of Open Access Journals (Sweden)

    K. Klauer

    2018-06-01

    Full Text Available Optical measuring instruments are widely used for the functional characterization of surface topography. However, due to the interaction of the surface with the incident light, effects occur that can influence the measured topography height values and the obtained surface texture parameters. Therefore, we describe a systematic investigation of the influences of optical surface topography measurement on the acquisition of function-oriented roughness parameters. The same evaluation areas of varying cylinder liners which represent a typical application of function-oriented roughness parameters were measured with a confocal microscope and a stylus instrument. Functional surface texture parameters as given in the standards ISO 13565–2, ISO 13565–3 and ISO 25178–2 were evaluated for both measurement methods and compared. The transmission of specific surface features was described and a correlation analysis for the surface topographies obtained with the different measurement methods and their resulting functional roughness parameters was carried out. Keywords: Functional surface characterization, Optical metrology, Topography measurement, Roughness

  6. Surface roughness control by extreme ultraviolet (EUV) radiation

    Science.gov (United States)

    Ahad, Inam Ul; Obeidi, Muhannad Ahmed; Budner, Bogusław; Bartnik, Andrzej; Fiedorowicz, Henryk; Brabazon, Dermot

    2017-10-01

    Surface roughness control of polymeric materials is often desirable in various biomedical engineering applications related to biocompatibility control, separation science and surface wettability control. In this study, Polyethylene terephthalate (PET) polymer films were irradiated with Extreme ultraviolet (EUV) photons in nitrogen environment and investigations were performed on surface roughness modification via EUV exposure. The samples were irradiated at 3 mm and 4 mm distance from the focal spot to investigate the effect of EUV fluence on topography. The topography of the EUV treated PET samples were studied by AFM. The detailed scanning was also performed on the sample irradiated at 3 mm. It was observed that the average surface roughness of PET samples was increased from 9 nm (pristine sample) to 280 nm and 253 nm for EUV irradiated samples. Detailed AFM studies confirmed the presence of 1.8 mm wide period U-shaped channels in EUV exposed PET samples. The walls of the channels were having FWHM of about 0.4 mm. The channels were created due to translatory movements of the sample in horizontal and transverse directions during the EUV exposure. The increased surface roughness is useful for many applications. The nanoscale channels fabricated by EUV exposure could be interesting for microfluidic applications based on lab-on-a-chip (LOC) devices.

  7. Benchmarking performance measurement and lean manufacturing in the rough mill

    Science.gov (United States)

    Dan Cumbo; D. Earl Kline; Matthew S. Bumgardner

    2006-01-01

    Lean manufacturing represents a set of tools and a stepwise strategy for achieving smooth, predictable product flow, maximum product flexibility, and minimum system waste. While lean manufacturing principles have been successfully applied to some components of the secondary wood products value stream (e.g., moulding, turning, assembly, and finishing), the rough mill is...

  8. Multifractal scaling analysis of autopoisoning reactions over a rough surface

    International Nuclear Information System (INIS)

    Chaudhari, Ajay; Yan, Ching-Cher Sanders; Lee, S.-L.

    2003-01-01

    Decay type diffusion-limited reactions (DLR) over a rough surface generated by a random deposition model were performed. To study the effect of the decay profile on the reaction probability distribution (RPD), multifractal scaling analysis has been carried out. The dynamics of these autopoisoning reactions are controlled by the two parameters in the decay function, namely, the initial sticking probability (P ini ) of every site and the decay rate (m). The smaller the decay rate, the narrower is the range of α values in the α-f(α) multifractal spectrum. The results are compared with the earlier work of DLR over a surface of diffusion-limited aggregation (DLA). We also considered here the autopoisoning reactions over a smooth surface for comparing our results, which show clearly how the roughness affects the chemical reactions. The q-τ(q) multifractal curves for the smooth surface are linear whereas those for the rough surface are nonlinear. The range of α values in the case of a rough surface is wider than that of the smooth surface

  9. Sustainability of road roughness measurements in countries with ...

    African Journals Online (AJOL)

    A research project was carried out to establish a sustainable procedure for road roughness measurement applicable in developing countries. Out of many devices in use today, a vehicle mounted bump integrator (VMBI) was selected for the reasons that: a) the equipment is available in most developing countries and it has ...

  10. Evaluation of rough lemon (Citrus jambhiri Lush.) as rootstock for ...

    African Journals Online (AJOL)

    Lakesh.Sharma

    2013-10-30

    Oct 30, 2013 ... rootstock for salinity tolerance at seedling stage under in vitro conditions ... INTRODUCTION. Around the world, citrus is one of the .... to summarize the general effect of different concentrations of NaCl on rough lemon on the ...

  11. Oblique roughness replication in strained SiGe/Si multilayers

    NARCIS (Netherlands)

    Holy, V.; Darhuber, A.A.; Stangl, J.; Bauer, G.; Nützel, J.-F.; Abstreiter, G.

    1998-01-01

    The replication of the interface roughness in SiGe/Si multilayers grown on miscut Si(001) substrates has been studied by means of x-ray reflectivity reciprocal space mapping. The interface profiles were found to be highly correlated and the direction of the maximal replication was inclined with

  12. Influence of roughness on capillary forces between hydrophilic surfaces

    NARCIS (Netherlands)

    van Zwol, P. J.; Palasantzas, G.; De Hosson, J. Th. M.

    Capillary forces have been measured by atomic force microscopy in the plate-sphere setup between gold, borosilicate glass, GeSbTe, titanium, and UV-irradiated amorphous titanium-dioxide surfaces. The force measurements were performed as a function contact time and surface roughness in the range

  13. Scales of form roughness on riverbanks with different riparian vegetation

    Science.gov (United States)

    Konsoer, K. M.; Rhoads, B. L.; Best, J.; Langendoen, E. J.; Ursic, M.; Abad, J. D.; Garcia, M. H.

    2013-12-01

    Riverbanks often include topographic irregularities that occur over a range of scales and that are produced by interactions among erosional processes, vegetation, and the geotechnical properties of the banks and floodplains. Irregularity of the bank surface can increase form drag, affecting the overall flow resistance, near-bank shear stresses, and patterns of sediment transport. Understanding how dominant scales of form roughness influence the near-bank flow structure, and thus the shear stress partitioning, is vital for the development of accurate predictive morphodynamic models. In this paper, the scales of bank roughness are examined for two meander bends of a large alluvial river with differing riparian vegetation on the Wabash River near Grayville, Illinois. Detailed measurements of bank topography were obtained using terrestrial LiDAR during low flow events and a multibeam echo sounder (MBES) during bankfull events. These measurements yielded high spatial resolution maps (~5-10 cm) that were used to analyze scales of roughness at different elevations along the banks during both subaerial and subaqueous conditions. The results of these analyses provide insight into the influence of riparian vegetation on form roughness and patterns of near-bank flow structure as documented using acoustic Doppler current profilers (ADCP).

  14. Surface roughness when diamond turning RSA 905 optical aluminium

    Science.gov (United States)

    Otieno, T.; Abou-El-Hossein, K.; Hsu, W. Y.; Cheng, Y. C.; Mkoko, Z.

    2015-08-01

    Ultra-high precision machining is used intensively in the photonics industry for the production of various optical components. Aluminium alloys have proven to be advantageous and are most commonly used over other materials to make various optical components. Recently, the increasing demand from optical systems for optical aluminium with consistent material properties has led to the development of newly modified grades of aluminium alloys produced by rapid solidification in the foundry process. These new aluminium grades are characterised by their finer microstructures and refined mechanical and physical properties. However the machining database of these new optical aluminium grades is limited and more research is still required to investigate their machinability performance when they are diamond turned in ultrahigh precision manufacturing environment. This work investigates the machinability of rapidly solidified aluminium RSA 905 by varying a number of diamond-turning cutting parameters and measuring the surface roughness over a cutting distance of 4 km. The machining parameters varied in this study were the cutting speed, feed rate and depth of cut. The results showed a common trend of decrease in surface roughness with increasing cutting distance. The lowest surface roughness Ra result obtained after 4 km in this study was 3.2 nm. This roughness values was achieved using a cutting speed of 1750 rpm, feed rate of 5 mm/min and depth of cut equal to 25 μm.

  15. Heat transfer and friction on smooth and rough test rods

    International Nuclear Information System (INIS)

    Franken, W.M.P.; Hoogland, H.; Deijman, P.

    1977-06-01

    Results are reported on heat transfer and pressure drop tests on one smooth and nine rough test rods in an annular geometry. The wall roughness consisted of transversal ribs with various roughness pitches, rib heights and rib widths. The tests were performed with air as coolant under a wide range of experimental conditions: 10 5 5 , 1.1 2. Special attention has been given to the effect of variation of the physical coolant properties over the flow cross section. This effect could be described by the power function (Tsub(w)/Tsub(b))sup(-0.3l) in additional systematic variation of the heat transfer could be recognized, dependent on the coolant temperature level. The experimental results were correlated by the equation St = C(Tsub(in)) Resup(-0.2) Prsup(-0.6) (Tsub(w)/Tsub(b)sup(-0.31). Values of C(Tsub(in)) are given in tabular form. The thermal entrance effect has been measured on various test rods. A substantial reduction of the heat transfer coefficient was almost constant along the rough test rods

  16. Modeling of interface roughness in thermoelectric composite materials

    International Nuclear Information System (INIS)

    Gather, F; Heiliger, C; Klar, P J

    2011-01-01

    We use a network model to calculate the influence of the mesoscopic interface structure on the thermoelectric properties of superlattice structures consisting of alternating layers of materials A and B. The thermoelectric figure of merit of such a composite material depends on the layer thickness, if interface resistances are accounted for, and can be increased by proper interface design. In general, interface roughness reduces the figure of merit, again compared to the case of ideal interfaces. However, the strength of this reduction depends strongly on the type of interface roughness. Smooth atomic surface diffusion leading to alloying of materials A and B causes the largest reduction of the figure of merit. Consequently, in real structures, it is important not only to minimize interface roughness, but also to control the type of roughness. Although the microscopic effects of interfaces are only empirically accounted for, using a network model can yield useful information about the dependence of the macroscopic transport coefficients on the mesoscopic disorder in structured thermoelectric materials.

  17. Determining the surface roughness coefficient by 3D Scanner

    Directory of Open Access Journals (Sweden)

    Karmen Fifer Bizjak

    2010-12-01

    Full Text Available Currently, several test methods can be used in the laboratory to determine the roughness of rock joint surfaces.However, true roughness can be distorted and underestimated by the differences in the sampling interval of themeasurement methods. Thus, these measurement methods produce a dead zone and distorted roughness profiles.In this paper a new rock joint surface roughness measurement method is presented, with the use of a camera-typethree-dimensional (3D scanner as an alternative to current methods. For this study, the surfaces of ten samples oftuff were digitized by means of a 3D scanner, and the results were compared with the corresponding Rock JointCoefficient (JRC values. Up until now such 3D scanner have been mostly used in the automotive industry, whereastheir use for comparison with obtained JRC coefficient values in rock mechanics is presented here for the first time.The proposed new method is a faster, more precise and more accurate than other existing test methods, and is apromising technique for use in this area of study in the future.

  18. Impact of human error on lumber yield in rough mills

    Science.gov (United States)

    Urs Buehlmann; R. Edward Thomas; R. Edward Thomas

    2002-01-01

    Rough sawn, kiln-dried lumber contains characteristics such as knots and bark pockets that are considered by most people to be defects. When using boards to produce furniture components, these defects are removed to produce clear, defect-free parts. Currently, human operators identify and locate the unusable board areas containing defects. Errors in determining a...

  19. Modeling and analysis for surface roughness and material removal ...

    African Journals Online (AJOL)

    The cutting parameters considered were tool nose radius, tool rake angle, feed rate, cutting speed, depth of cut and cutting environment (dry, wet and cooled) on the surface roughness and material removal ... A second order mathematical model in terms of cutting parameters is also developed using regression modeling.

  20. Influence of Surface Roughness of Stainless steel on Microbial Adhesion

    DEFF Research Database (Denmark)

    Bagge, D.; Hilbert, Lisbeth Rischel; Gram, L.

    2002-01-01

    Bacterial adhesion and biofilm formation is of growing interest in the food processing industry where bacteria can survive on surfaces and resist cleaning and disinfection. The condition of the surfaces (eg lack of cracks) and their general roughness is assumed to be important for the hygienic...

  1. Dynamics of wetting on smooth and rough surfaces.

    NARCIS (Netherlands)

    Cazabat, A.M.; Cohen Stuart, M.A.

    1987-01-01

    The rate of spreading of non-volatile liquids on smooth and on rough surfaces was investigated. The radius of the wetted spot was found to agree with recently proposed scaling laws (t 1/10 for capillarity driven andt 1/8 for gravity driven spreading) when the surface was smooth. However, the

  2. Peptostreptococcus micros smooth and rough genotypes in periodontitis and gingivitis

    NARCIS (Netherlands)

    Kremer, BHA; Loos, BG; van der Velden, U; van Winkelhoff, AJ; Craandijk, J; Bulthuis, HM; Hutter, J; Varoufaki, AS; van Steenbergen, TJM

    Background: Two genotypes can be distinguished within the species Peptostreptococcus micros: a smooth (Sm) and a rough (Rg) type. To date no systematic study has been performed on the prevalence and proportion of both types in untreated periodontitis patients and subjects without destructive

  3. Squeeze film between porous rough elliptical plates | Deheri ...

    African Journals Online (AJOL)

    The roughness of the bearing surface is described by a stochastic random variable with non zero mean, variance and skew ness. The associated Reynolds' equation is solved with appropriate boundary conditions. Results for bearing performance characteristics such as load carrying capacity and response time for different ...

  4. Estimation of scattering from a moist rough surface with spheroidal ...

    Indian Academy of Sciences (India)

    Administrator

    less than 5⋅5% of the magnetic wavelength. We empha- size that the surface deviation is responsible for scattering at a given electromagnetic wavelength. 2. Theoretical consideration (basic theory). We consider a horizontally rough surface with slight per- centage of moisture (2–4⋅5%) with spheroidal dust parti- cles.

  5. Modelling dune evolution and dynamic roughness in rivers

    NARCIS (Netherlands)

    Paarlberg, Andries

    2008-01-01

    Accurate river flow models are essential tools for water managers, but these hydraulic simulation models often lack a proper description of dynamic roughness due to hysteresis effects in dune evolution. To incorporate the effects of dune evolution directly into the resistance coefficients of

  6. Differential equations driven by rough paths with jumps

    Science.gov (United States)

    Friz, Peter K.; Zhang, Huilin

    2018-05-01

    We develop the rough path counterpart of Itô stochastic integration and differential equations driven by general semimartingales. This significantly enlarges the classes of (Itô/forward) stochastic differential equations treatable with pathwise methods. A number of applications are discussed.

  7. Calibrating the Truax Rough Rider seed drill for restoration plantings

    Science.gov (United States)

    Loren St. John; Brent Cornforth; Boyd Simonson; Dan Ogle; Derek Tilley

    2008-01-01

    The purpose of this technical note is to provide a step-by-step approach to calibrating the Truax Rough Rider range drill, a relatively new, state-of-the-art rangeland drill. To achieve the desired outcome of a seeding project, an important step following proper weed control and seedbed preparation is the calibration of the seeding equipment to ensure the recommended...

  8. RMS slope of exponentially correlated surface roughness for radar applications

    DEFF Research Database (Denmark)

    Dierking, Wolfgang

    2000-01-01

    In radar signature analysis, the root mean square (RMS) surface slope is utilized to assess the relative contribution of multiple scattering effects. For an exponentially correlated surface, an effective RMS slope can be determined by truncating the high frequency tail of the roughness spectrum...

  9. Multilayer roughness and image formation in the Schwarzschild objective

    International Nuclear Information System (INIS)

    Singh, S.; Solak, H.; Cerrina, F.

    1996-01-01

    We present a study of the effect of multilayer-surface-roughness-induced scattering in the image formation of the Schwarzschild objective (SO) used in the spectromicroscope MAXIMUM. The two mirrors comprising the SO are coated with Ru/B 4 C multilayers that have a peak reflectivity at 130 eV. We had long observed that a diffuse x-ray background surrounds the focused x-ray spot. The spatial resolution remains at 0.1 μm in spite of this. However, since a significant fraction of the flux is lost to the background, since too large an area of the sample is illuminated, and since the S/N ratio is degraded, the origins of this effect merit investigation. This diffuse background resulting from x-ray scattering at the surface of the mirrors was mapped out using bidirectional knife edge scans. Complementary surface roughness simulations were carried out with the ray-tracing program SHADOW. AFM experiments were also done to directly measure the surface roughness and power spectrum of representative multilayers. Following curve fitting, it was possible to classify Gaussian components in both the measured and simulated profiles as arising from scattering occurring at either the convex primary mirror or the concave secondary mirror. Together with geometrical analysis, these techniques permitted us to track the image formation process of an actual optical system in the presence of surface roughness. copyright 1996 American Institute of Physics

  10. Fractal characteristics of fracture roughness and aperture data

    International Nuclear Information System (INIS)

    Kumar, S.; Boernge, J.

    1991-05-01

    In this study mathematical expressions are developed for the characteristics of apertures between rough surfaces. It has shown that the correlation between the opposite surfaces influences the aperture properties and different models are presented for these different surface correlations. Fracture and apertures profiles measured from intact fractures are evaluated and it is found that they qualitatively follow the mathematically predicted trends

  11. Surface roughness of orthodontic band cements with different compositions

    Directory of Open Access Journals (Sweden)

    Françoise Hélène van de Sande

    2011-06-01

    Full Text Available OBJECTIVES: The present study evaluated comparatively the surface roughness of four orthodontic band cements after storage in various solutions. MATERIAL AND METHODS: Eight standardized cylinders were made from 4 materials: zinc phosphate cement (ZP, compomer (C, resin-modified glass ionomer cement (RMGIC and resin cement (RC. Specimens were stored for 24 h in deionized water and immersed in saline (pH 7.0 or 0.1 M lactic acid solution (pH 4.0 for 15 days. Surface roughness readings were taken with a profilometer (Surfcorder SE1200 before and after the storage period. Data were analyzed by two-way ANOVA and Tukey's test (comparison among cements and storage solutions or paired t-test (comparison before and after the storage period at 5% significance level. RESULTS: The values for average surface roughness were statistically different (pRMGIC>C>R (p0.05. Compared to the current threshold (0.2 µm related to biofilm accumulation, both RC and C remained below the threshold, even after acidic challenge by immersion in lactic acid solution. CONCLUSIONS: Storage time and immersion in lactic acid solution increased the surface roughness of the majority of the tested cements. RC presented the smoothest surface and it was not influenced by storage conditions.

  12. Surface roughness and morphologic changes of zirconia: Effect of ...

    African Journals Online (AJOL)

    4-6 W/20 Hz presented significantly effect in surface roughness changes of zirconia than other surface treatments. Key words:Erbium, chromium: Yttrium, scandium, gallium, garnet laser, scanning electron .... ZrO2, (f) After sintering ZrO2 in letter “e”, (g) 2 W laser irridiation pre-sintered ZrO2, (h) After ..... Acta Odontol Scand.

  13. Influence of surface roughness on streptococcal adhesion forces to composite resins

    NARCIS (Netherlands)

    Mei, Li; Busscher, Henk J; van der Mei, Henny C; Ren, Yijin

    OBJECTIVE: To determine streptococcal adhesion forces with composite resins with different surface roughness. METHODS: Polishing and grinding were applied to obtain smooth (roughness 20 nm), moderately rough (150 nm) and rough (350 nm) surfaces of two orthodontic, light-cured composites. Adhesion

  14. Direct numerical simulation of open channel flow over smooth-to-rough and rough-to-smooth step changes

    Science.gov (United States)

    Rouhi, Amirreza; Chung, Daniel; Hutchins, Nicholas

    2017-11-01

    Direct numerical simulations (DNSs) are reported for open channel flow over streamwise-alternating patches of smooth and fully rough walls. Owing to the streamwise periodicity, the flow configuration is composed of a step change from smooth to rough, and a step change from rough to smooth. The friction Reynolds number varies from 443 over the smooth patch to 715 over the rough patch. The flow is thoroughly studied by mean and fluctuation profiles, and spectrograms. The detailed flow from DNS reveals discrepancies of up to 50% among the various definitions of the internal-layer thickness, with apparent power-law exponents differing by up to 60%. The definition based on the logarithmic slope of the velocity profile, as proposed by Chamorro et al. (Boundary-Layer Meteorol., vol. 130, 2009, pp. 29-41), is most consistent with the physical notion of the internal layer; this is supported by the defect similarity based on this internal-layer thickness, and the streamwise homogeneity of the dissipation length-scale within this internal layer. The statistics inside this internal-layer, and the growth of the internal layer itself, are minimally affected by the streamwise periodicity when the patch length is at least six times the channel height.

  15. Archivage électronique : spécifications relatives à la conception et à l'exploitation de systèmes informatiques en vue d'assurer la conservation et l'intégrité des documents stockés dans ces systèmes

    CERN Document Server

    Association Française de Normalisation. Paris

    2007-01-01

    Archivage électronique : spécifications relatives à la conception et à l'exploitation de systèmes informatiques en vue d'assurer la conservation et l'intégrité des documents stockés dans ces systèmes

  16. Relative roughness controls on incipient sediment motion in steep channels

    Science.gov (United States)

    Prancevic, J.; Lamb, M. P.; Fuller, B. M.

    2012-12-01

    For over eight decades, researchers have noted an appreciable increase in the nondimensional shear stress (Shields number) at initiation of fluvial bedload transport with increasing bed slope. The precise cause of the trend, however, is obscured by the covariance of several factors with increased slope: a greater downstream component of the gravity acting on the grains and fluid, changes in bed morphology, increased grainsize relative to the channel width that may lead to grain bridging, and increased grainsize relative to flow depth (relative roughness) that may change flow hydraulics and particle buoyancy. Here, we report on ongoing laboratory experiments spanning a wide range of bed slopes (2% to 67%) designed to isolate these variables and determine the true cause of heightened critical Shields numbers on steep slopes. First, we eliminated bed morphology as a factor by using only planar beds. To investigate the effect of grain bridging, we used two different channel widths, representing width-to-grainsize ratios of 23:1 and 9:1. Finally, to separate the effects of slope from relative roughness, we compared incipient motion conditions for acrylic particles (submerged specific gravity of 0.15) to natural siliciclastic gravel (submerged specific gravity of 1.65). Different particle densities allowed us to explore incipient motion as a function of relative roughness, independent of channel slope, because lighter particles move at shallower flow depths than heavier ones of the same size. Results show that both materials exhibit a positive trend between bed slope and critical Shields number despite the existence of planar beds for all slopes. Furthermore, changing the grainsize-to-width ratio had a negligible effect on this trend. For all slopes, the critical Shields number for bedload transport was higher for the acrylic particles than for gravel, indicating that relative roughness has a strong control on incipient sediment motion independent of channel slope. These

  17. Numerical simulation of electroosmotic flow in rough microchannels using the lattice Poisson-Nernst-Planck methods

    Science.gov (United States)

    Kamali, Reza; Soloklou, Mohsen Nasiri; Hadidi, Hooman

    2018-05-01

    In this study, coupled Lattice Boltzmann method is applied to solve the dynamic model for an electroosmotic flow and investigate the effects of roughness in a 2-D flat microchannel. In the present model, the Poisson equation is solved for the electrical potential, the Nernst- Planck equation is solved for the ion concentration. In the analysis of electroosmotic flows, when the electric double layers fully overlap or the convective effects are not negligible, the Nernst-Planck equation must be used to find the ionic distribution throughout the microchannel. The effects of surface roughness height, roughness interval spacing and roughness surface potential on flow conditions are investigated for two different configurations of the roughness, when the EDL layers fully overlap through the microchannel. The results show that in both arrangements of roughness in homogeneously charged rough channels, the flow rate decreases by increasing the roughness height. A discrepancy in the mass flow rate is observed when the roughness height is about 0.15 of the channel width, which its average is higher for the asymmetric configuration and this difference grows by increasing the roughness height. In the symmetric roughness arrangement, the mass flow rate increases until the roughness interval space is almost 1.5 times the roughness width and it decreases for higher values of the roughness interval space. For the heterogeneously charged rough channel, when the roughness surface potential ψr is less than channel surface potential ψs , the net charge density increases by getting far from the roughness surface, while in the opposite situation, when ψs is more than ψr , the net charge density decreases from roughness surface to the microchannel middle center. Increasing the roughness surface potential induces stronger electric driving force on the fluid which results in larger velocities in the flow.

  18. Thriving rough sets 10th anniversary : honoring professor Zdzisław Pawlak's life and legacy & 35 years of rough sets

    CERN Document Server

    Skowron, Andrzej; Yao, Yiyu; Ślęzak, Dominik; Polkowski, Lech

    2017-01-01

    This special book is dedicated to the memory of Professor Zdzisław Pawlak, the father of rough set theory, in order to commemorate both the 10th anniversary of his passing and 35 years of rough set theory. The book consists of 20 chapters distributed into four sections, which focus in turn on a historical review of Professor Zdzisław Pawlak and rough set theory; a review of the theory of rough sets; the state of the art of rough set theory; and major developments in rough set based data mining approaches. Apart from Professor Pawlak’s contributions to rough set theory, other areas he was interested in are also included. Moreover, recent theoretical studies and advances in applications are also presented. The book will offer a useful guide for researchers in Knowledge Engineering and Data Mining by suggesting new approaches to solving the problems they encounter.

  19. Film Thickness and Friction Relationship in Grease Lubricated Rough Contacts

    Directory of Open Access Journals (Sweden)

    David Gonçalves

    2017-08-01

    Full Text Available The relationship between the film generation and the coefficient of friction in grease lubricated contacts was investigated. Ball-on-disc tests were performed under different operating conditions: entrainment speed, lubricant temperature and surface roughness. The tests were performed with fully formulated greases and their base oils. The greases were formulated with different thickener types and also different base oils natures and viscosities. Film thickness measurements were performed in ball-on-glass disc tests, and Stribeck curves were measured in ball-on-steel disc tests with discs of different roughness. The role of the thickener and the base oil nature/viscosity on the film thickness and coefficient of friction was addressed and the greases’ performance was compared based on their formulation.

  20. Capillary-induced crack healing between surfaces of nanoscale roughness.

    Science.gov (United States)

    Soylemez, Emrecan; de Boer, Maarten P

    2014-10-07

    Capillary forces are important in nature (granular materials, insect locomotion) and in technology (disk drives, adhesion). Although well studied in equilibrium state, the dynamics of capillary formation merit further investigation. Here, we show that microcantilever crack healing experiments are a viable experimental technique for investigating the influence of capillary nucleation on crack healing between rough surfaces. The average crack healing velocity, v̅, between clean hydrophilic polycrystalline silicon surfaces of nanoscale roughness is measured. A plot of v̅ versus energy release rate, G, reveals log-linear behavior, while the slope |d[log(v̅)]/dG| decreases with increasing relative humidity. A simplified interface model that accounts for the nucleation time of water bridges by an activated process is developed to gain insight into the crack healing trends. This methodology enables us to gain insight into capillary bridge dynamics, with a goal of attaining a predictive capability for this important microelectromechanical systems (MEMS) reliability failure mechanism.

  1. Asperity interaction in adhesive contact of metallic rough surfaces

    International Nuclear Information System (INIS)

    Sahoo, Prasanta; Banerjee, Atanu

    2005-01-01

    The analysis of adhesive contact of metallic rough surfaces considering the effect of asperity interaction is the subject of this investigation. The micro-contact model of asperity interactions developed by Zhao and Chang (2001 Trans. ASME: J. Tribol. 123 857-64) is combined with the elastic plastic adhesive contact model developed by Chang et al (1988 Trans. ASME: J. Tribol. 110 50-6) to consider the asperity interaction and elastic-plastic deformation in the presence of surface forces simultaneously. The well-established elastic adhesion index and plasticity index are used to consider the different contact conditions. Results show that asperity interaction influences the load-separation behaviour in elastic-plastic adhesive contact of metallic rough surfaces significantly and, in general, adhesion is reduced due to asperity interactions

  2. Survey of surface roughness properties of synchrotron radiation optics

    International Nuclear Information System (INIS)

    Takacs, P.Z.; Colbert, J.; Church, E.L.

    1986-03-01

    Measurements of surface roughness were made on a large number of grazing incidence mirrors delivered for use at the National Synchrotron Light Source (NSLS) at Brookhaven National Laboratory. The measurements were made with a WYKO optical profiler using a 2.5X and a 10X objective and analyzed with our PROFILE code to generate an average periodogram representation for each surface. The data is presented in the form of representative profiles with all of the periodogram curves arranged according to figure type. Analysis of the periodograms allows one to compute bandwidth-limited values for RMS roughness and slope, to provide valuable feedback information to manufacturers regarding compliance with specifications, and to predict the performance of the optic at x-ray wavelengths

  3. Thickness and roughness measurements of nano thin films by interference

    Directory of Open Access Journals (Sweden)

    A Sabzalipour

    2011-06-01

    Full Text Available In the standard optical interference fringes approach, by measuring shift of the interference fringes due to step edge of thin film on substrate, thickness of the layer has already been measured. In order to improve the measurement precision of this popular method, the interference fringes intensity curve was extracted and analyzed before and after the step preparation. By this method, one can measure a few nanometers films thickness. In addition, using the interference fringes intensity curve and its fluctuations, the roughness of surface is measured within a few nanometers accuracy. Comparison of our results with some direct methods of thickness and roughness measurements, i.e. using surface profilemeter and atomic force microscopy confirms the accuracy of the suggested improvements.

  4. Stability analysis of rough surfaces in adhesive normal contact

    Science.gov (United States)

    Rey, Valentine; Bleyer, Jeremy

    2018-03-01

    This paper deals with adhesive frictionless normal contact between one elastic flat solid and one stiff solid with rough surface. After computation of the equilibrium solution of the energy minimization principle and respecting the contact constraints, we aim at studying the stability of this equilibrium solution. This study of stability implies solving an eigenvalue problem with inequality constraints. To achieve this goal, we propose a proximal algorithm which enables qualifying the solution as stable or unstable and that gives the instability modes. This method has a low computational cost since no linear system inversion is required and is also suitable for parallel implementation. Illustrations are given for the Hertzian contact and for rough contact.

  5. Generation of nano roughness on fibrous materials by atmospheric plasma

    International Nuclear Information System (INIS)

    Kulyk, I; Scapinello, M; Stefan, M

    2012-01-01

    Atmospheric plasma technology finds novel applications in textile industry. It eliminates the usage of water and of hazard liquid chemicals, making production much more eco-friendly and economically convenient. Due to chemical effects of atmospheric plasma, it permits to optimize dyeing and laminating affinity of fabrics, as well as anti-microbial treatments. Other important applications such as increase of mechanical resistance of fiber sleeves and of yarns, anti-pilling properties of fabrics and anti-shrinking property of wool fabrics were studied in this work. These results could be attributed to the generation of nano roughness on fibers surface by atmospheric plasma. Nano roughness generation is extensively studied at different conditions. Alternative explanations for the important practical results on textile materials and discussed.

  6. Investigation on Surface Roughness of Inconel 718 in Photochemical Machining

    Directory of Open Access Journals (Sweden)

    Nitin D. Misal

    2017-01-01

    Full Text Available The present work is focused on estimating the optimal machining parameters required for photochemical machining (PCM of an Inconel 718 and effects of these parameters on surface topology. An experimental analysis was carried out to identify optimal values of parameters using ferric chloride (FeCl3 as an etchant. The parameters considered in this analysis are concentration of etchant, etching time, and etchant temperature. The experimental analysis shows that etching performance as well as surface topology improved by appropriate selection of etching process parameters. Temperature of the etchant found to be dominant parameter in the PCM of Inconel 718 for surface roughness. At optimal etching conditions, surface roughness was found to be 0.201 μm.

  7. In situ surface roughness measurement using a laser scattering method

    Science.gov (United States)

    Tay, C. J.; Wang, S. H.; Quan, C.; Shang, H. M.

    2003-03-01

    In this paper, the design and development of an optical probe for in situ measurement of surface roughness are discussed. Based on this light scattering principle, the probe which consists of a laser diode, measuring lens and a linear photodiode array, is designed to capture the scattered light from a test surface with a relatively large scattering angle ϕ (=28°). This capability increases the measuring range and enhances repeatability of the results. The coaxial arrangement that incorporates a dual-laser beam and a constant compressed air stream renders the proposed system insensitive to movement or vibration of the test surface as well as surface conditions. Tests were conducted on workpieces which were mounted on a turning machine that operates with different cutting speeds. Test specimens which underwent different machining processes and of different surface finish were also studied. The results obtained demonstrate the feasibility of surface roughness measurement using the proposed method.

  8. Compact terahertz spectrometer based on disordered rough surfaces

    Science.gov (United States)

    Yang, Tao; Jiang, Bing; Ge, Jia-cheng; Zhu, Yong-yuan; Li, Xing-ao; Huang, Wei

    2018-01-01

    In this paper, a compact spectrometer based on disordered rough surfaces for operation in the terahertz band is presented. The proposed spectrometer consists of three components, which are used for dispersion, modulation and detection respectively. The disordered rough surfaces, which are acted as the dispersion component, are modulated by the modulation component. Different scattering intensities are captured by the detection component with different extent of modulation. With a calibration measurement process, one can reconstruct the spectra of the probe terahertz beam by solving a system of simultaneous linear equations. A Tikhonov regularization approach has been implemented to improve the accuracy of the spectral reconstruction. The reported broadband, compact, high-resolution terahertz spectrometer is well suited for portable terahertz spectroscopy applications.

  9. Simulations of roughness initiation and growth on railway rails

    Science.gov (United States)

    Sheng, X.; Thompson, D. J.; Jones, C. J. C.; Xie, G.; Iwnicki, S. D.; Allen, P.; Hsu, S. S.

    2006-06-01

    A model for the prediction of the initiation and growth of roughness on the rail is presented. The vertical interaction between a train and the track is calculated as a time history for single or multiple wheels moving on periodically supported rails, using a wavenumber-based approach. This vertical dynamic wheel/rail force arises from the varying stiffness due to discrete supports (i.e. parametric excitation) and the roughness excitation on the railhead. The tangential contact problem between the wheel and rail is modelled using an unsteady two-dimensional approach and also using the three-dimensional contact model, FASTSIM. This enables the slip and stick regions in the contact patch to be identified from the input geometry and creepage between the wheel and rail. The long-term wear growth is then predicted by applying repeated passages of the vehicle wheelsets, as part of an iterative solution.

  10. Inertia of rough and vicinal surfaces of helium-4 crystals

    International Nuclear Information System (INIS)

    Amrit, J.; Legros, P.; Poitrenaud, J.

    1995-01-01

    This paper reports a study of the inertia of rough and vicinal of 4 He crystals. We have measured the transmission coefficient of ultrasonic waves at frequencies 10, 30, 50 and 70 MHz, across the liquid-solid interface. The experiments are carried out at temperatures ranging between 0.4 and 1.0 K for four crystallographic orientations. Two important phenomena are put to evidence for the first time. We have found the first experimental evidence that the inertia of rough surfaces depends on temperature. For vicinal surfaces, we have shown the strong increase of the inertia as the tilt angle decreases. Our experimental results agree very well with the theoretical predictions

  11. Response of neutral boundary-layers to changes of roughness

    DEFF Research Database (Denmark)

    Sempreviva, Anna Maria; Larsen, Søren Ejling; Mortensen, Niels Gylling

    1990-01-01

    boundary layer where again the drag laws can be used to estimate the surface wind. To study this problem, data have been sampled for two years from four 30-m meteorological masts placed from 0 to 30 km inland from the North Sea coast of Jutland in Denmark. The present analysis is limited to neutral......When air blows across a change in surface roughness, an internal boundary layer (IBL) develops within which the wind adapts to the new surface. This process is well described for short fetches, > 1 km. However, few data exist for large fetches on how the IBL grows to become a new equilibrium...... stratification, and the surface roughness is the main parameter. The analysis of wind data and two simple models, a surface layer and a planetary boundary layer (PBL) model, are described. Results from both models are discussed and compared with data analysis. Model parameters have been evaluated and the model...

  12. Nanoscale roughness contact in a slider-disk interface.

    Science.gov (United States)

    Hua, Wei; Liu, Bo; Yu, Shengkai; Zhou, Weidong

    2009-07-15

    The nanoscale roughness contact between molecularly smooth surfaces of a slider-disk interface in a hard disk drive is analyzed, and the lubricant behavior at very high shear rate is presented. A new contact model is developed to study the nanoscale roughness contact behavior by classifying various forms of contact into slider-lubricant contact, slider-disk elastic contact and plastic contact. The contact pressure and the contact probabilities of the three types of contact are investigated. The new contact model is employed to explain and provide insight to an interesting experimental result found in a thermal protrusion slider. The protrusion budget for head surfing in the lubricant, which is the ideal state for contact recording, is also discussed.

  13. Nanoscale roughness contact in a slider-disk interface

    International Nuclear Information System (INIS)

    Hua Wei; Liu Bo; Yu Shengkai; Zhou Weidong

    2009-01-01

    The nanoscale roughness contact between molecularly smooth surfaces of a slider-disk interface in a hard disk drive is analyzed, and the lubricant behavior at very high shear rate is presented. A new contact model is developed to study the nanoscale roughness contact behavior by classifying various forms of contact into slider-lubricant contact, slider-disk elastic contact and plastic contact. The contact pressure and the contact probabilities of the three types of contact are investigated. The new contact model is employed to explain and provide insight to an interesting experimental result found in a thermal protrusion slider. The protrusion budget for head surfing in the lubricant, which is the ideal state for contact recording, is also discussed.

  14. Variable precision rough set for multiple decision attribute analysis

    Institute of Scientific and Technical Information of China (English)

    Lai; Kin; Keung

    2008-01-01

    A variable precision rough set (VPRS) model is used to solve the multi-attribute decision analysis (MADA) problem with multiple conflicting decision attributes and multiple condition attributes. By introducing confidence measures and a β-reduct, the VPRS model can rationally solve the conflicting decision analysis problem with multiple decision attributes and multiple condition attributes. For illustration, a medical diagnosis example is utilized to show the feasibility of the VPRS model in solving the MADA...

  15. Rough terrain motion planning for actively reconfigurable mobile robots

    Energy Technology Data Exchange (ETDEWEB)

    Brunner, Michael

    2015-02-05

    In the aftermath of the Tohoku earthquake and the nuclear meltdown at the power plant of Fukushima Daiichi in 2011, reconfigurable robots like the iRobot Packbot were deployed. Instead of humans, the robots were used to investigate contaminated areas. Other incidents are the two major earthquakes in Northern Italy in May 2012. Besides many casualties, a large number of historical buildings was severely damaged. Due to the imminent danger of collapse, it was too dangerous for rescue personnel to enter many of the buildings. Therefore, the sites were inspected by reconfigurable robots, which are able to traverse the rubble and debris of the partially destroyed buildings. This thesis develops a navigation system enabling wheeled and tracked robots to safely traverse rough terrain and challenging structures. It consists of a planning mechanism and a controller. The focus of this thesis, however, is on the contribution to motion planning. The planning scheme employs a hierarchical approach to motion planning for actively reconfigurable robots in rough environments. Using a map of the environment the algorithm estimates the traversability under the consideration of uncertainties. Based on this analysis, an initial path search determines an approximate solution with respect to the robot's operating limits.Subsequently, a detailed planning step refines the initial path where it is required. The refinement step considers the robot's actuators and stability in addition to the quantities of the first search. Determining the robot-terrain interaction is very important in rough terrain. This thesis presents two path refinement approaches: a deterministic and a randomized approach. The experimental evaluation investigates the separate components of the planning scheme, the robot-terrain interaction for instance.In simulation as well as in real world experiments the evaluation demonstrates the necessity of such a planning algorithm in rough terrain and it provides

  16. Characterizing developing adverse pressure gradient flows subject to surface roughness

    Science.gov (United States)

    Brzek, Brian; Chao, Donald; Turan, Özden; Castillo, Luciano

    2010-04-01

    An experimental study was conducted to examine the effects of surface roughness and adverse pressure gradient (APG) on the development of a turbulent boundary layer. Hot-wire anemometry measurements were carried out using single and X-wire probes in all regions of a developing APG flow in an open return wind tunnel test section. The same experimental conditions (i.e., T ∞, U ref, and C p) were maintained for smooth, k + = 0, and rough, k + = 41-60, surfaces with Reynolds number based on momentum thickness, 3,000 carefully designed such that the x-dependence in the flow field was known. Despite this fact, only a very small region of the boundary layer showed a balance of the various terms in the integrated boundary layer equation. The skin friction computed from this technique showed up to a 58% increase due to the surface roughness. Various equilibrium parameters were studied and the effect of roughness was investigated. The generated flow was not in equilibrium according to the Clauser (J Aero Sci 21:91-108, 1954) definition due to its developing nature. After a development region, the flow reached the equilibrium condition as defined by Castillo and George (2001), where Λ = const, is the pressure gradient parameter. Moreover, it was found that this equilibrium condition can be used to classify developing APG flows. Furthermore, the Zagarola and Smits (J Fluid Mech 373:33-79, 1998a) scaling of the mean velocity deficit, U ∞δ*/δ, can also be used as a criteria to classify developing APG flows which supports the equilibrium condition of Castillo and George (2001). With this information a ‘full APG region’ was defined.

  17. Rough terrain motion planning for actively reconfigurable mobile robots

    International Nuclear Information System (INIS)

    Brunner, Michael

    2015-01-01

    In the aftermath of the Tohoku earthquake and the nuclear meltdown at the power plant of Fukushima Daiichi in 2011, reconfigurable robots like the iRobot Packbot were deployed. Instead of humans, the robots were used to investigate contaminated areas. Other incidents are the two major earthquakes in Northern Italy in May 2012. Besides many casualties, a large number of historical buildings was severely damaged. Due to the imminent danger of collapse, it was too dangerous for rescue personnel to enter many of the buildings. Therefore, the sites were inspected by reconfigurable robots, which are able to traverse the rubble and debris of the partially destroyed buildings. This thesis develops a navigation system enabling wheeled and tracked robots to safely traverse rough terrain and challenging structures. It consists of a planning mechanism and a controller. The focus of this thesis, however, is on the contribution to motion planning. The planning scheme employs a hierarchical approach to motion planning for actively reconfigurable robots in rough environments. Using a map of the environment the algorithm estimates the traversability under the consideration of uncertainties. Based on this analysis, an initial path search determines an approximate solution with respect to the robot's operating limits.Subsequently, a detailed planning step refines the initial path where it is required. The refinement step considers the robot's actuators and stability in addition to the quantities of the first search. Determining the robot-terrain interaction is very important in rough terrain. This thesis presents two path refinement approaches: a deterministic and a randomized approach. The experimental evaluation investigates the separate components of the planning scheme, the robot-terrain interaction for instance.In simulation as well as in real world experiments the evaluation demonstrates the necessity of such a planning algorithm in rough terrain and it provides

  18. Optimization of surface roughness parameters in dry turning

    OpenAIRE

    R.A. Mahdavinejad; H. Sharifi Bidgoli

    2009-01-01

    Purpose: The precision of machine tools on one hand and the input setup parameters on the other hand, are strongly influenced in main output machining parameters such as stock removal, toll wear ratio and surface roughnes.Design/methodology/approach: There are a lot of input parameters which are effective in the variations of these output parameters. In CNC machines, the optimization of machining process in order to predict surface roughness is very important.Findings: From this point of view...

  19. Roughness Effects on the Formation of a Leading Edge Vortex

    Science.gov (United States)

    Elliott, Cassidy; Lang, Amy; Wahidi, Redha; Wilroy, Jacob

    2017-11-01

    Microscopic scales cover the wings of Monarch butterflies, creating a patterned surface that acts as a natural energy capture mechanism. This patterning is thought to delay the growth of the leading edge vortex (LEV) produced by the flapping motion of a wing. Increased skin friction caused by the scales leads to a weaker LEV being shed into the butterfly's wake, lessening drag and increasing flight efficiency. To test how this roughness effects LEV formation, a plate of random roughness was designed in SolidWorks and printed on the Objet 30 Pro 3D printer. A 2x3x5 cubic foot tow tank was used to test the rough plate at Reynold's numbers of 1500, 3000, and 6000 (velocities of 8, 16, and 32 mm/s) at an angle of attack of 45 degrees. Images were captured of the LEV generated when the plate was towed upwards through the particle-seeded flow. These images were used to determine the XY velocity of the particles using a technique called Digital Particle Image Velocimetry (DPIV). Codes written in MATLAB were used to track and measure the strength of the LEV. Circulation values for the randomly-rough plate were then compared to the same values generated in a previous experiment that used a smooth plate and a grooved plate to determine the effect of the patterning on vortex development. Funding for this research project was provided by the National Science Foundation under the Research Experience for Undergraduates (REU) program (REU Supplement CBET 1628600 under CBET 1335848).

  20. Fuzzy Linguistic Optimization on Surface Roughness for CNC Turning

    OpenAIRE

    Lan, Tian-Syung

    2010-01-01

    Surface roughness is often considered the main purpose in contemporary computer numerical controlled (CNC) machining industry. Most existing optimization researches for CNC finish turning were either accomplished within certain manufacturing circumstances or achieved through numerous equipment operations. Therefore, a general deduction optimization scheme is deemed to be necessary for the industry. In this paper, the cutting depth, feed rate, speed, and tool nose runoff with low, medium, and...

  1. Velocity distribution in a turbulent flow near a rough wall

    Science.gov (United States)

    Korsun, A. S.; Pisarevsky, M. I.; Fedoseev, V. N.; Kreps, M. V.

    2017-11-01

    Velocity distribution in the zone of developed wall turbulence, regardless of the conditions on the wall, is described by the well-known Prandtl logarithmic profile. In this distribution, the constant, that determines the value of the velocity, is determined by the nature of the interaction of the flow with the wall and depends on the viscosity of the fluid, the dynamic velocity, and the parameters of the wall roughness.In extreme cases depending on the ratio between the thickness of the viscous sublayer and the size of the roughness the constant takes on a value that does not depend on viscosity, or leads to a ratio for a smooth wall.It is essential that this logarithmic profile is the result not only of the Prandtl theory, but can be derived from general considerations of the theory of dimensions, and also follows from the condition of local equilibrium of generation and dissipation of turbulent energy in the wall area. This allows us to consider the profile as a universal law of velocity distribution in the wall area of a turbulent flow.The profile approximation up to the maximum speed line with subsequent integration makes possible to obtain the resistance law for channels of simple shape. For channels of complex shape with rough walls, the universal profile can be used to formulate the boundary condition when applied to the calculation of turbulence models.This paper presents an empirical model for determining the constant of the universal logarithmic profile. The zone of roughness is described by a set of parameters and is considered as a porous structure with variable porosity.

  2. Statistics of zero crossings in rough interfaces with fractional elasticity

    Science.gov (United States)

    Zamorategui, Arturo L.; Lecomte, Vivien; Kolton, Alejandro B.

    2018-04-01

    We study numerically the distribution of zero crossings in one-dimensional elastic interfaces described by an overdamped Langevin dynamics with periodic boundary conditions. We model the elastic forces with a Riesz-Feller fractional Laplacian of order z =1 +2 ζ , such that the interfaces spontaneously relax, with a dynamical exponent z , to a self-affine geometry with roughness exponent ζ . By continuously increasing from ζ =-1 /2 (macroscopically flat interface described by independent Ornstein-Uhlenbeck processes [Phys. Rev. 36, 823 (1930), 10.1103/PhysRev.36.823]) to ζ =3 /2 (super-rough Mullins-Herring interface), three different regimes are identified: (I) -1 /2 value in the system size, or decays as a power-law towards (II) a subextensive or (III) an intensive value. In the steady state, the distribution of intervals between zeros changes from an exponential decay in (I) to a power-law decay P (ℓ ) ˜ℓ-γ in (II) and (III). While in (II) γ =1 -θ with θ =1 -ζ the steady-state persistence exponent, in (III) we obtain γ =3 -2 ζ , different from the exponent γ =1 expected from the prediction θ =0 for infinite super-rough interfaces with ζ >1 . The effect on P (ℓ ) of short-scale smoothening is also analyzed numerically and analytically. A tight relation between the mean interval, the mean width of the interface, and the density of zeros is also reported. The results drawn from our analysis of rough interfaces subject to particular boundary conditions or constraints, along with discretization effects, are relevant for the practical analysis of zeros in interface imaging experiments or in numerical analysis.

  3. Dynamical structure of the turbulent boundary layer on rough surface

    Czech Academy of Sciences Publication Activity Database

    Uruba, Václav; Jonáš, Pavel; Hladík, Ondřej

    2011-01-01

    Roč. 11, č. 1 (2011), s. 603-604 ISSN 1617-7061 R&D Projects: GA ČR GA101/08/1112; GA ČR GAP101/10/1230 Institutional research plan: CEZ:AV0Z20760514 Keywords : turbulent boundary layer * rough wall * hairpin vortex Subject RIV: BK - Fluid Dynamics http://onlinelibrary.wiley.com/doi/10.1002/pamm.201110291/abstract

  4. Computer simulation of RBS spectra from samples with surface roughness

    Czech Academy of Sciences Publication Activity Database

    Malinský, Petr; Hnatowicz, Vladimír; Macková, Anna

    2016-01-01

    Roč. 371, MAR (2016), s. 101-105 ISSN 0168-583X. [22nd International conference on Ion Beam Analysis (IBA). Opatija, 14.06.2015-19.06.2015] R&D Projects: GA MŠk(CZ) LM2011019; GA ČR GA15-01602S Institutional support: RVO:61389005 Keywords : computer simulation * Rutherford backscattering * surface roughness Subject RIV: BG - Nuclear, Atomic and Molecular Physics, Colliders Impact factor: 1.109, year: 2016

  5. Kinetic theory of a rarefied gas of rough spheres

    International Nuclear Information System (INIS)

    Kremer, G.M.

    1987-01-01

    A Kinetic theory for the rarefied gas consisting of rough-spherical molecules is developed, in which a macroscopic state is characterized by the 29 scalar fields of density, velocity, pressure tensor, temperature, translational heat flux, rotational heat flux, spin and spin flux. The relations of Navier-Stokes and Fourier are obtained by the use of an iteration method akin to the Maxwellian procedure. (author) [pt

  6. Biofilm roughness determines Cryptosporidium parvum retention in environmental biofilms.

    Science.gov (United States)

    DiCesare, E A Wolyniak; Hargreaves, B R; Jellison, K L

    2012-06-01

    The genus Cryptosporidium is a group of waterborne protozoan parasites that have been implicated in significant outbreaks of gastrointestinal infections throughout the world. Biofilms trap these pathogens and can contaminate water supplies through subsequent release. Biofilm microbial assemblages were collected seasonally from three streams in eastern Pennsylvania and used to grow biofilms in laboratory microcosms. Daily oocyst counts in the influx and efflux flow allowed the calculation of daily oocyst retention in the biofilm. Following the removal of oocysts from the influx water, oocyst attachment to the biofilm declined to an equilibrium state within 5 days that was sustained for at least 25 days. Varying the oocyst loading rate for the system showed that biofilm retention could be saturated, suggesting that discrete binding sites determined the maximum number of oocysts retained. Oocyst retention varied seasonally but was consistent across all three sites; however, seasonal oocyst retention was not consistent across years at the same site. No correlation between oocyst attachment and any measured water quality parameter was found. However, oocyst retention was strongly correlated with biofilm surface roughness and roughness varied among seasons and across years. We hypothesize that biofilm roughness and oocyst retention are dependent on environmentally driven changes in the biofilm community rather than directly on water quality conditions. It is important to understand oocyst transport dynamics to reduce risks of human infection. Better understanding of factors controlling biofilm retention of oocysts should improve our understanding of oocyst transport at different scales.

  7. Scanning electron microscopy and roughness study of dental composite degradation.

    Science.gov (United States)

    Soares, Luís Eduardo Silva; Cortez, Louise Ribeiro; Zarur, Raquel de Oliveira; Martin, Airton Abrahão

    2012-04-01

    Our aim was to test the hypothesis that the use of mouthwashes, consumption of soft drinks, as well as the type of light curing unit (LCU), would change the surface roughness (Ra) and morphology of a nanofilled composite resin (Z350® 3M ESPE). Samples (80) were divided into eight groups: Halogen LCU, group 1, saliva (control); group 2, Pepsi Twist®; group 3, Listerine®; group 4, Colgate Plax®; LED LCU, group 5, saliva; group 6, Pepsi Twist®; group 7, Listerine®; group 8, Colgate Plax®. Ra values were measured at baseline, and after 7 and 14 days. One specimen of each group was prepared for scanning electron microscopy analysis after 14 days. The data were subjected to multifactor analysis of variance at a 95% confidence followed by Tukey's honestly significant difference post-hoc test. All the treatments resulted in morphological changes in composite resin surface, and the most significant change was in Pepsi Twist® groups. The samples of G6 had the greatest increase in Ra. The immersion of nanofilled resin in mouthwashes with alcohol and soft drink increases the surface roughness. Polymerization by halogen LCU (reduced light intensity) associated with alcohol contained mouthwash resulted in significant roughness on the composite.

  8. Interfacial layering and capillary roughness in immiscible liquids.

    Science.gov (United States)

    Geysermans, P; Pontikis, V

    2010-08-21

    The capillary roughness and the atomic density profiles of extended interfaces between immiscible liquids are determined as a function of the interface area by using molecular dynamics and Lennard-Jones (12-6) potentials. We found that with increasing area, the interface roughness diverges logarithmically, thus fitting the theoretical mean-field prediction. In systems small enough for the interfacial roughness not to blur the structural details, atomic density profiles across the fluid interface are layered with correlation length in the range of molecular correlations in liquids. On increasing the system size, the amplitude of the thermally excited position fluctuations of the interface increases, thus causing layering to rapidly vanish, if density profiles are computed without special care. In this work, we present and validate a simple method, operating in the direct space, for extracting from molecular dynamics trajectories the "intrinsic" structure of a fluid interface that is the local density profile of the interface cleaned from capillary wave effects. Estimated values of interfacial properties such as the tension, the intrinsic width, and the lower wavelength limit of position fluctuations are in agreement with results collected from the literature.

  9. Atmospheric stability analysis over statically and dynamically rough surfaces

    Science.gov (United States)

    Maric, Emina; Metzger, Meredith; Singha, Arindam; Sadr, Reza

    2011-11-01

    The ratio of buoyancy flux to turbulent kinetic energy production in the atmospheric surface layer is investigated experimentally for air flow over two types of surfaces characterized by static and dynamic roughness. In this study, ``static'' refers to the time-invariant nature of naturally-occurring roughness over a mud/salt playa; while, ``dynamic'' refers to the behavior of water waves along an air-water interface. In both cases, time-resolved measurements of the momentum and heat fluxes were acquired from synchronized 3D sonic anemometers mounted on a vertical tower. Field campaigns were conducted at two sites, representing the ``statically'' and ``dynamically'' rough surfaces, respectively: (1) the SLTEST facility in Utah's western desert, and (2) the new Doha airport in Qatar under construction along the coast of the Persian Gulf. Note, at site 2, anemometers were located directly above the water by extension from a tower secured to the end of a 1 km-long pier. Comparisons of the Monin-Obukhov length, flux Richardson number, and gradient Richardson number are presented, and discussed in the context of the observed evolution of the turbulent spectra in response to diurnal variations of atmospheric stability. Supported by the Qatar National Research Fund.

  10. UNCERTAINTY HANDLING IN DISASTER MANAGEMENT USING HIERARCHICAL ROUGH SET GRANULATION

    Directory of Open Access Journals (Sweden)

    H. Sheikhian

    2015-08-01

    Full Text Available Uncertainty is one of the main concerns in geospatial data analysis. It affects different parts of decision making based on such data. In this paper, a new methodology to handle uncertainty for multi-criteria decision making problems is proposed. It integrates hierarchical rough granulation and rule extraction to build an accurate classifier. Rough granulation provides information granules with a detailed quality assessment. The granules are the basis for the rule extraction in granular computing, which applies quality measures on the rules to obtain the best set of classification rules. The proposed methodology is applied to assess seismic physical vulnerability in Tehran. Six effective criteria reflecting building age, height and material, topographic slope and earthquake intensity of the North Tehran fault have been tested. The criteria were discretized and the data set was granulated using a hierarchical rough method, where the best describing granules are determined according to the quality measures. The granules are fed into the granular computing algorithm resulting in classification rules that provide the highest prediction quality. This detailed uncertainty management resulted in 84% accuracy in prediction in a training data set. It was applied next to the whole study area to obtain the seismic vulnerability map of Tehran. A sensitivity analysis proved that earthquake intensity is the most effective criterion in the seismic vulnerability assessment of Tehran.

  11. Roughness Effects on the Formation of a Leading Edge Vortex

    Science.gov (United States)

    Elliott, Cassidy; Lang, Amy; Wahidi, Redha; Wilroy, Jacob

    2016-11-01

    Microscopic scales cover the wings of Monarch butterflies, creating a patterned surface. This patterning is an important natural flow control mechanism that is thought to delay the growth of the leading edge vortex (LEV) produced by the flapping motion of a wing. The increased skin friction caused by the scales leads to a weaker LEV being shed into the butterfly's wake, lessening drag and increasing flight efficiency. To test this theory, a plate of random roughness was designed in SolidWorks and printed on the Objet 30 Pro 3D printer. A 2x3x5 cubic foot tow tank was used to test the rough plate at Reynold's numbers of 1500, 3000, and 6000 (velocities of 8, 16, and 32 mm/s) at an angle of attack of 45 degrees. Particle Image Velocimetry (PIV) captured images of the LEV generated by the plate when towed upwards through the particle-seeded flow. Codes written in MatLab were used to automatically track and determine the strength of the LEV. Circulation values for the randomly-rough plate were then compared to the same values generated in a previous experiment that used a smooth plate and a grooved plate to determine the effect of the patterning on vortex development. Funding provided by NSF REU site Grant EEC 1358991 and CBET 1628600.

  12. Combined Radar-Radiometer Surface Soil Moisture and Roughness Estimation

    Science.gov (United States)

    Akbar, Ruzbeh; Cosh, Michael H.; O'Neill, Peggy E.; Entekhabi, Dara; Moghaddam, Mahta

    2017-01-01

    A robust physics-based combined radar-radiometer, or Active-Passive, surface soil moisture and roughness estimation methodology is presented. Soil moisture and roughness retrieval is performed via optimization, i.e., minimization, of a joint objective function which constrains similar resolution radar and radiometer observations simultaneously. A data-driven and noise-dependent regularization term has also been developed to automatically regularize and balance corresponding radar and radiometer contributions to achieve optimal soil moisture retrievals. It is shown that in order to compensate for measurement and observation noise, as well as forward model inaccuracies, in combined radar-radiometer estimation surface roughness can be considered a free parameter. Extensive Monte-Carlo numerical simulations and assessment using field data have been performed to both evaluate the algorithms performance and to demonstrate soil moisture estimation. Unbiased root mean squared errors (RMSE) range from 0.18 to 0.03 cm3cm3 for two different land cover types of corn and soybean. In summary, in the context of soil moisture retrieval, the importance of consistent forward emission and scattering development is discussed and presented.

  13. Capillary adhesion between elastic solids with randomly rough surfaces

    International Nuclear Information System (INIS)

    Persson, B N J

    2008-01-01

    I study how the contact area and the work of adhesion between two elastic solids with randomly rough surfaces depend on the relative humidity. The surfaces are assumed to be hydrophilic, and capillary bridges form at the interface between the solids. For elastically hard solids with relatively smooth surfaces, the area of real contact and therefore also the sliding friction are maximal when there is just enough liquid to fill out the interfacial space between the solids, which typically occurs for d K ∼3h rms , where d K is the height of the capillary bridge and h rms the root-mean-square roughness of the (combined) surface roughness profile. For elastically soft solids, the area of real contact is maximal for very low humidity (i.e. small d K ), where the capillary bridges are able to pull the solids into nearly complete contact. In both cases, the work of adhesion is maximal (and equal to 2γcosθ, where γ is the liquid surface tension and θ the liquid-solid contact angle) when d K >> h rms , corresponding to high relative humidity

  14. Roughness influence on human blood drop spreading and splashing

    Science.gov (United States)

    Smith, Fiona; Buntsma, Naomi; Brutin, David

    2017-11-01

    The impact behaviour of complex fluid droplets is a topic that has been extensively studied but with much debate. The Bloodstain Pattern Analysis (BPA) community is encountering this scientific problem with daily practical cases since they use bloodstains as evidence in crime scene reconstruction. We aim to provide fundamental explanations in the study of blood drip stains by investigating the influence of surface roughness and wettability on the splashing limit of droplets of blood, a non-Newtonian colloidal fluid. Droplets of blood impacting perpendicularly different surfaces at different velocities were recorded. The recordings were analysed as well as the surfaces characteristics in order to find an empirical solution since we found that roughness plays a major role in the threshold of the splashing/non-splashing behaviour of blood compared to the wettability. Moreover it appears that roughness alters the deformation of the drip stains. These observations are key in characterising features of drip stains with the impacting conditions, which would answer some forensic issues.

  15. Turbidity removal: Gravel and charcoal as roughing filtration media

    Directory of Open Access Journals (Sweden)

    Josiah A. Adeyemo

    2010-10-01

    Full Text Available Roughing filtration is an important pre-treatment process for wastewater, because it efficiently separates fine solid particles over prolonged periods, without the addition of chemicals. For this study, a pilot plant was designed at Delmas Coal Mine in the Mpumalanga province of South Africa. The design and sizing of the pilot plant was guided by Wegelin’s design criteria. Gravel was used as a control medium because it is one of the most commonly used roughing filter media and because it was used in developing the criteria. We compared the performance of gravel as a filter medium to that of another locally available material, charcoal, for the removal of turbidity in wastewater. The pilot plant was monitored continuously for 90 days from commissioning until the end of the project. The overall performance of the roughing filter in turbidity removal, using gravel or charcoal, was considered efficient for the pre-treatment of waste water. Charcoal performed slightly better than gravel as a filter medium for the removal of turbidity, possibly because charcoal has a slightly higher specific surface area and porosity than gravel, which could enhance sedimentation and other filtration processes, such as adsorption, respectively.

  16. Granular computing in decision approximation an application of rough mereology

    CERN Document Server

    Polkowski, Lech

    2015-01-01

    This book presents a study in knowledge discovery in data with knowledge understood as a set of relations among objects and their properties. Relations in this case are implicative decision rules and the paradigm in which they are induced is that of computing with granules defined by rough inclusions, the latter introduced and studied  within rough mereology, the fuzzified version of mereology. In this book basic classes of rough inclusions are defined and based on them methods for inducing granular structures from data are highlighted. The resulting granular structures are subjected to classifying algorithms, notably k—nearest  neighbors and bayesian classifiers. Experimental results are given in detail both in tabular and visualized form for fourteen data sets from UCI data repository. A striking feature of granular classifiers obtained by this approach is that preserving the accuracy of them on original data, they reduce  substantially the size of the granulated data set as well as the set of granular...

  17. Effect of geometric base roughness on size segregation

    Directory of Open Access Journals (Sweden)

    Jing L.

    2017-01-01

    Full Text Available The geometric roughness at boundaries has a profound impact on the dynamics of granular flows. For a bumpy base made of fixed particles, two major factors have been separately studied in the literature, namely, the size and spatial distribution of base particles. A recent work (Jing et al. 2016 has proposed a roughness indicator Ra, which combines both factors for any arbitrary bumpy base comprising equally-sized spheres. It is shown in mono-disperse flows that as Ra increases, a transition occurs from slip (Ra 0.62 conditions. This work focuses on such a phase transition in bi-disperse flows, in which Ra can be a function of time. As size segregation takes place, large particles migrate away from the bottom, leading to a variation of size ratio between flow- and base-particles. As a result, base roughness Ra evolves with the progress of segregation. Consistent with the slip/non-slip transition in mono-disperse flows, basal sliding arises at low values of Ra and the development of segregation might be affected; when Ra increases to a certain level (Ra > 0.62, non-slip condition is respected. This work extends the validity of Ra to bi-disperse flows, which can be used to understand the geometric boundary effect during segregation.

  18. Rough-wall turbulent boundary layers with constant skin friction

    KAUST Repository

    Sridhar, A.

    2017-03-28

    A semi-empirical model is presented that describes the development of a fully developed turbulent boundary layer in the presence of surface roughness with length scale ks that varies with streamwise distance x . Interest is centred on flows for which all terms of the von Kármán integral relation, including the ratio of outer velocity to friction velocity U+∞≡U∞/uτ , are streamwise constant. For Rex assumed large, use is made of a simple log-wake model of the local turbulent mean-velocity profile that contains a standard mean-velocity correction for the asymptotic fully rough regime and with assumed constant parameter values. It is then shown that, for a general power-law external velocity variation U∞∼xm , all measures of the boundary-layer thickness must be proportional to x and that the surface sand-grain roughness scale variation must be the linear form ks(x)=αx , where x is the distance from the boundary layer of zero thickness and α is a dimensionless constant. This is shown to give a two-parameter (m,α) family of solutions, for which U+∞ (or equivalently Cf ) and boundary-layer thicknesses can be simply calculated. These correspond to perfectly self-similar boundary-layer growth in the streamwise direction with similarity variable z/(αx) , where z is the wall-normal coordinate. Results from this model over a range of α are discussed for several cases, including the zero-pressure-gradient ( m=0 ) and sink-flow ( m=−1 ) boundary layers. Trends observed in the model are supported by wall-modelled large-eddy simulation of the zero-pressure-gradient case for Rex in the range 108−1010 and for four values of α . Linear streamwise growth of the displacement, momentum and nominal boundary-layer thicknesses is confirmed, while, for each α , the mean-velocity profiles and streamwise turbulent variances are found to collapse reasonably well onto z/(αx) . For given α , calculations of U+∞ obtained from large-eddy simulations are streamwise

  19. Mars radar clutter and surface roughness characteristics from MARSIS data

    Science.gov (United States)

    Campbell, Bruce A.; Schroeder, Dustin M.; Whitten, Jennifer L.

    2018-01-01

    Radar sounder studies of icy, sedimentary, and volcanic settings can be affected by reflections from surface topography surrounding the sensor nadir location. These off-nadir ;clutter; returns appear at similar time delays to subsurface echoes and complicate geologic interpretation. Additionally, broadening of the radar echo in delay by surface returns sets a limit on the detectability of subsurface interfaces. We use MARSIS 4 MHz data to study variations in the nadir and off-nadir clutter echoes, from about 300 km to 1000 km altitude, R, for a wide range of surface roughness. This analysis uses a new method of characterizing ionospheric attenuation to merge observations over a range of solar zenith angle and date. Mirror-like reflections should scale as R-2, but the observed 4 MHz nadir echoes often decline by a somewhat smaller power-law factor because MARSIS on-board processing increases the number of summed pulses with altitude. Prior predictions of the contributions from clutter suggest a steeper decline with R than the nadir echoes, but in very rough areas the ratio of off-nadir returns to nadir echoes shows instead an increase of about R1/2 with altitude. This is likely due in part to an increase in backscatter from the surface as the radar incidence angle at some round-trip time delay declines with increasing R. It is possible that nadir and clutter echo properties in other planetary sounding observations, including RIME and REASON flyby data for Europa, will vary in the same way with altitude, but there may be differences in the nature and scale of target roughness (e.g., icy versus rocky surfaces). We present global maps of the ionosphere- and altitude-corrected nadir echo strength, and of a ;clutter; parameter based on the ratio of off-nadir to nadir echoes. The clutter map offers a view of surface roughness at ∼75 m length scale, bridging the spatial-scale gap between SHARAD roughness estimates and MOLA-derived parameters.

  20. Electromagnetic Scattering Characteristics of Fractal Rough Coated Objects in the Terahertz Range

    Directory of Open Access Journals (Sweden)

    Zhao Hua

    2018-02-01

    Full Text Available Based on the physical optics method, the scattering characteristics of fractal rough surface coated objects are studied in the terahertz (THz range herein. A blunt model based on fractal rough surfaces is built. The surface current is calculated according to the Fresnel reflection coefficient, and the Radar Cross Section (RCS of the rough coated target is obtained. The RCS of rough and smooth surface targets are compared. Numerical results for a rough coated blunt cone model are provided, and discussed from the perspective of different frequencies and coating thickness values. The results show that the surface roughness of the target has a significant effect on scattering in the terahertz range.

  1. LBA-ECO LC-15 Aerodynamic Roughness Maps of Vegetation Canopies, Amazon Basin: 2000

    Data.gov (United States)

    National Aeronautics and Space Administration — This data set, LBA-ECO LC-15 Aerodynamic Roughness Maps of Vegetation Canopies, Amazon Basin: 2000, provides physical roughness maps of vegetation canopies in the...

  2. Modeling of surface roughness effects on Stokes flow in circular pipes

    Science.gov (United States)

    Song, Siyuan; Yang, Xiaohu; Xin, Fengxian; Lu, Tian Jian

    2018-02-01

    Fluid flow and pressure drop across a channel are significantly influenced by surface roughness on a channel wall. The present study investigates the effects of periodically structured surface roughness upon flow field and pressure drop in a circular pipe at low Reynolds numbers. The periodic roughness considered exhibits sinusoidal, triangular, and rectangular morphologies, with the relative roughness (i.e., ratio of the amplitude of surface roughness to hydraulic diameter of the pipe) no more than 0.2. Based upon a revised perturbation theory, a theoretical model is developed to quantify the effect of roughness on fully developed Stokes flow in the pipe. The ratio of static flow resistivity and the ratio of the Darcy friction factor between rough and smooth pipes are expressed in four-order approximate formulations, which are validated against numerical simulation results. The relative roughness and the wave number are identified as the two key parameters affecting the static flow resistivity and the Darcy friction factor.

  3. The effect of surface roughness on the performances of liner-piston ...

    African Journals Online (AJOL)

    The effect of surface roughness on the performances of liner-piston ring contact in internal combustion engine. ... The surface roughness between the liner and the piston rings, plays an ... EMAIL FREE FULL TEXT EMAIL FREE FULL TEXT

  4. Thermal Infrared Spectra of Microcrystalline Sedimentary Phases: Effects of Natural Surface Roughness on Spectral Feature Shape

    Science.gov (United States)

    Hardgrove, C.; Rogers, A. D.

    2012-03-01

    Thermal infrared spectral features of common microcrystalline phases (chert, alabaster, micrite) are presented. Spectra are sensitive to mineralogy and micron-scale (~1-25 µm) surface roughness. Roughness is on the scale of the average crystal size.

  5. Experimental methodology of contact edge roughness on sub-100-nm pattern

    Science.gov (United States)

    Lee, Tae Yong; Ihm, Dongchul; Kang, Hyo Chun; Lee, Jun Bum; Lee, Byoung-Ho; Chin, Soo-Bok; Cho, Do-Hyun; Kim, Yang Hyong; Yang, Ho Dong; Yang, Kyoung Mo

    2004-05-01

    The measurement of edge roughness has become a hot issue in the semiconductor industry. Major vendors offer a variety of features to measure the edge roughness in their CD-SEMs. However, most of the features are limited by the applicable pattern types. For the line and space patterns, features such as Line Edge Roughness (LER) and Line Width Roughness (LWR) are available in current CD-SEMs. The edge roughness is more critical in contact process. However the measurement of contact edge roughness (CER) or contact space roughness (CSR) is more complicated than that of LER or LWR. So far, no formal standard measurement algorithm or definition of contact roughness measurement exists. In this article, currently available features are investigated to assess their representability for CER or CSR. Some new ideas to quantify CER and CSR were also suggested with preliminary experimental results.

  6. Elastic–plastic adhesive contact of non-Gaussian rough surfaces

    Indian Academy of Sciences (India)

    Adhesion; asymmetric roughness; elastic–plastic contact; non-Gaussian rough surfaces. ... model of contact deformation that is based on accurate Finite Element Analysis (FEA) of an elastic–plastic single asperity contact. ... Sadhana | News.

  7. Change of Surface Roughness and Planetary Boundary Layer

    DEFF Research Database (Denmark)

    Jensen, Niels Otto

    1978-01-01

    The ratio between upstream and far downstream surface friction velocities relative to a change in surface roughness is given on the basis of results from surface Rossby number similarity theory. By simple theories for the internal boundary layer, which are found to compare quite well with recent...... numerical results from higher-order closure models, it is found that, even at a downwind distance such that the internal boundary layer has grown to the full height of the planetary boundary layers, the surface stress still considerably exceeds the equilibrium value...

  8. Rough Set Approach to Incomplete Multiscale Information System

    Science.gov (United States)

    Yang, Xibei; Qi, Yong; Yu, Dongjun; Yu, Hualong; Song, Xiaoning; Yang, Jingyu

    2014-01-01

    Multiscale information system is a new knowledge representation system for expressing the knowledge with different levels of granulations. In this paper, by considering the unknown values, which can be seen everywhere in real world applications, the incomplete multiscale information system is firstly investigated. The descriptor technique is employed to construct rough sets at different scales for analyzing the hierarchically structured data. The problem of unravelling decision rules at different scales is also addressed. Finally, the reduct descriptors are formulated to simplify decision rules, which can be derived from different scales. Some numerical examples are employed to substantiate the conceptual arguments. PMID:25276852

  9. Analytical fitting model for rough-surface BRDF.

    Science.gov (United States)

    Renhorn, Ingmar G E; Boreman, Glenn D

    2008-08-18

    A physics-based model is developed for rough surface BRDF, taking into account angles of incidence and scattering, effective index, surface autocovariance, and correlation length. Shadowing is introduced on surface correlation length and reflectance. Separate terms are included for surface scatter, bulk scatter and retroreflection. Using the FindFit function in Mathematica, the functional form is fitted to BRDF measurements over a wide range of incident angles. The model has fourteen fitting parameters; once these are fixed, the model accurately describes scattering data over two orders of magnitude in BRDF without further adjustment. The resulting analytical model is convenient for numerical computations.

  10. Influence of interface roughness in quantum cascade lasers

    International Nuclear Information System (INIS)

    Krivas, K. A.; Winge, D. O.; Franckié, M.; Wacker, A.

    2015-01-01

    We use a numerical model based on non-equilibrium Green's functions to investigate the influence of interface roughness (IFR) scattering in terahertz quantum cascade lasers. We confirm that IFR is an important phenomenon that affects both current and gain. The simulations indicate that IFR causes a leakage current that transfers electrons from the upper to the lower laser state. In certain cases, this current can greatly reduce gain. In addition, individual interfaces and their impact on the renormalized single particle energies are studied and shown to give both blue- and red-shifts of the gain spectrum

  11. Effective roughness calculated from satellite-derived land cover maps and hedge-information used in a weather forecasting model

    DEFF Research Database (Denmark)

    Hasager, C.B.; Nielsen, N.,W.; Jensen, N.O.

    2003-01-01

    differences. Especially the roughness variations can give a significantly different value between the equilibrium roughness in each of the patches as compared to the aggregated roughness value, the so-called effective roughness, for the grid cell. The effective roughness is a quantity that secures the physics...

  12. Contact area calculation between elastic solids bounded by mound rough surfaces

    NARCIS (Netherlands)

    Palasantzas, G

    In this work, we investigate the influence of mound roughness on the contact area between elastic bodies. The mound roughness is described by the r.m.s. roughness amplitude w, the average mound separation Lambda, and the system correlation length xi. In general, the real contact area has a complex

  13. Self-affine roughness influence on the friction coefficient for rubbers onto solid surfaces

    NARCIS (Netherlands)

    Palasantzas, G

    2004-01-01

    In this paper we investigate the influence of self-affine roughness on the friction coefficient mu(f) of a rubber body under incomplete contact onto a solid surface. The roughness is characterized by the rms amplitude w, the correlation length xi, and the roughness exponent H. It is shown that with

  14. Quality factor due to roughness scattering of shear horizontal surface acoustic waves in nanoresonators

    NARCIS (Netherlands)

    Palasantzas, G.

    2008-01-01

    In this work we study the quality factor associated with dissipation due to scattering of shear horizontal surface acoustic waves by random self-affine roughness. It is shown that the quality factor is strongly influenced by both the surface roughness exponent H and the roughness amplitude w to

  15. Performance of Color Camera Machine Vision in Automated Furniture Rough Mill Systems

    Science.gov (United States)

    D. Earl Kline; Agus Widoyoko; Janice K. Wiedenbeck; Philip A. Araman

    1998-01-01

    The objective of this study was to evaluate the performance of color camera machine vision for lumber processing in a furniture rough mill. The study used 134 red oak boards to compare the performance of automated gang-rip-first rough mill yield based on a prototype color camera lumber inspection system developed at Virginia Tech with both estimated optimum rough mill...

  16. Spatially-varying surface roughness and ground-level air quality in an operational dispersion model

    International Nuclear Information System (INIS)

    Barnes, M.J.; Brade, T.K.; MacKenzie, A.R.; Whyatt, J.D.; Carruthers, D.J.; Stocker, J.; Cai, X.; Hewitt, C.N.

    2014-01-01

    Urban form controls the overall aerodynamic roughness of a city, and hence plays a significant role in how air flow interacts with the urban landscape. This paper reports improved model performance resulting from the introduction of variable surface roughness in the operational air-quality model ADMS-Urban (v3.1). We then assess to what extent pollutant concentrations can be reduced solely through local reductions in roughness. The model results suggest that reducing surface roughness in a city centre can increase ground-level pollutant concentrations, both locally in the area of reduced roughness and downwind of that area. The unexpected simulation of increased ground-level pollutant concentrations implies that this type of modelling should be used with caution for urban planning and design studies looking at ventilation of pollution. We expect the results from this study to be relevant for all atmospheric dispersion models with urban-surface parameterisations based on roughness. -- Highlights: • Spatially variable roughness improved performance of an operational model. • Scenario modelling explored effect of reduced roughness on air pollution. • Reducing surface roughness can increase modelled ground-level pollution. • Damped vertical mixing outweighs increased horizontal advection in model study. • Result should hold for any model with a land-surface coupling based on roughness. -- Spatially varying roughness improves model simulations of urban air pollutant dispersion. Reducing roughness does not always decrease ground-level pollution concentrations

  17. Influence of self-affine roughness on the friction coefficient of rubber at high sliding velocity

    NARCIS (Netherlands)

    Palasantzas, G

    2004-01-01

    In this work we investigate the influence of self-affine roughness on the friction coefficient of a rubber body onto a solid surface at high speeds. The roughness is characterized by the rms amplitude w, the correlation length xi, and the roughness exponent H. It is shown that the friction

  18. An IDS Alerts Aggregation Algorithm Based on Rough Set Theory

    Science.gov (United States)

    Zhang, Ru; Guo, Tao; Liu, Jianyi

    2018-03-01

    Within a system in which has been deployed several IDS, a great number of alerts can be triggered by a single security event, making real alerts harder to be found. To deal with redundant alerts, we propose a scheme based on rough set theory. In combination with basic concepts in rough set theory, the importance of attributes in alerts was calculated firstly. With the result of attributes importance, we could compute the similarity of two alerts, which will be compared with a pre-defined threshold to determine whether these two alerts can be aggregated or not. Also, time interval should be taken into consideration. Allowed time interval for different types of alerts is computed individually, since different types of alerts may have different time gap between two alerts. In the end of this paper, we apply proposed scheme on DAPRA98 dataset and the results of experiment show that our scheme can efficiently reduce the redundancy of alerts so that administrators of security system could avoid wasting time on useless alerts.

  19. Roughness-dependent tribology effects on discontinuous shear thickening.

    Science.gov (United States)

    Hsu, Chiao-Peng; Ramakrishna, Shivaprakash N; Zanini, Michele; Spencer, Nicholas D; Isa, Lucio

    2018-05-15

    Surface roughness affects many properties of colloids, from depletion and capillary interactions to their dispersibility and use as emulsion stabilizers. It also impacts particle-particle frictional contacts, which have recently emerged as being responsible for the discontinuous shear thickening (DST) of dense suspensions. Tribological properties of these contacts have been rarely experimentally accessed, especially for nonspherical particles. Here, we systematically tackle the effect of nanoscale surface roughness by producing a library of all-silica, raspberry-like colloids and linking their rheology to their tribology. Rougher surfaces lead to a significant anticipation of DST onset, in terms of both shear rate and solid loading. Strikingly, they also eliminate continuous thickening. DST is here due to the interlocking of asperities, which we have identified as "stick-slip" frictional contacts by measuring the sliding of the same particles via lateral force microscopy (LFM). Direct measurements of particle-particle friction therefore highlight the value of an engineering-tribology approach to tuning the thickening of suspensions. Copyright © 2018 the Author(s). Published by PNAS.

  20. Wave-current generated turbulence over hemisphere bottom roughness

    Science.gov (United States)

    Barman, Krishnendu; Roy, Sayahnya; Debnath, Koustuv

    2018-03-01

    The present paper explores the effect of wave-current interaction on the turbulence characteristics and the distribution of eddy structure over artificially crammed rough bed prepared with hemispheres. The effect of the surface wave on temporal and spatial-averaged mean velocity, intensity, Reynolds shear stress over, within cavity and above the hemispherical bed are discussed. Detailed three-dimensional time series velocity components were measured in a tilting flume using 3-D Micro-Acoustic Doppler Velocimeter (ADV) at a Reynolds number, 62 × 103. This study reports the fractional contributions of burst-sweep cycles dominating the total shear stress near hemispherical rough surface both for current only flow as well as for wave-induced cases. Wavelet analysis of the fluctuating velocity signal shows that the superimposed wave of frequency 1 Hz is capable of modulating the energy containing a range of velocity fluctuations at the mid-depth of the cavity region (formed due to the crammed arrangement of the hemispheres). As a result, the large-scale eddies (with large values of wavelet coefficients) are concentrated at a pseudo-frequency which is equal to the wave oscillating frequency. On the other hand, it is observed that the higher wave frequency (2 Hz) is incapable of modulating the eddy structures at that particular region.

  1. Deposition of toxic metal particles on rough nanofiltration membranes

    Energy Technology Data Exchange (ETDEWEB)

    Agboola, Oluranti; Maree, Jannie; Mbaya, Richard; Zvinowanda, Caliphs Musa [Tshwane University of Technology, Pretoria (South Africa); Molelekwa, Gomotsegang Fred; Jullok, Nora; Bruggen, Bart Van der; Volodine, Alexander; Haesendonck, Chris Van [KU Leuven, Heverlee (Belgium)

    2014-08-15

    Two nanofiltration (NF90 and Nano-Pro-3012) membranes were investigated for their capacity to remove metal ions. This study presents the effect of membrane roughness on the removal of toxic metal ions during dead end membrane filtration. Atomic force microscopy, scanning electron microscopy, WSXM software and ImageJ were used to characterize the roughness of the membranes. Gradual decrease in filtration permeate flux was observed as foulants accumulated at the interface of the membranes; filtration permeate flux varied from 20 L/m{sup 2}/h to 14 L/m{sup 2}/h and 11 L/ m{sup 2}/h to 6 L/m{sup 2}/h for NF90 and Nano-Pro-3012, respectively. NF90 membrane was more prone to fouling than the Nano-Pro-3012 membrane: the percentage flux reduction was higher for NF90 (3.6%) than Nano-Pro-3012 (0.98%). The bearing ratio of the fouled NF90 exhibited a high peak of 7.09 nm than the fouled Nano-Pro-3012 with the peak of 6.8 nm.

  2. Deposition of toxic metal particles on rough nanofiltration membranes

    International Nuclear Information System (INIS)

    Agboola, Oluranti; Maree, Jannie; Mbaya, Richard; Zvinowanda, Caliphs Musa; Molelekwa, Gomotsegang Fred; Jullok, Nora; Bruggen, Bart Van der; Volodine, Alexander; Haesendonck, Chris Van

    2014-01-01

    Two nanofiltration (NF90 and Nano-Pro-3012) membranes were investigated for their capacity to remove metal ions. This study presents the effect of membrane roughness on the removal of toxic metal ions during dead end membrane filtration. Atomic force microscopy, scanning electron microscopy, WSXM software and ImageJ were used to characterize the roughness of the membranes. Gradual decrease in filtration permeate flux was observed as foulants accumulated at the interface of the membranes; filtration permeate flux varied from 20 L/m 2 /h to 14 L/m 2 /h and 11 L/ m 2 /h to 6 L/m 2 /h for NF90 and Nano-Pro-3012, respectively. NF90 membrane was more prone to fouling than the Nano-Pro-3012 membrane: the percentage flux reduction was higher for NF90 (3.6%) than Nano-Pro-3012 (0.98%). The bearing ratio of the fouled NF90 exhibited a high peak of 7.09 nm than the fouled Nano-Pro-3012 with the peak of 6.8 nm

  3. The Rough Field and The Grafted Tongue of Northern Ireland

    Directory of Open Access Journals (Sweden)

    John Engle

    1999-01-01

    Full Text Available The Rough Field de John Montague a été publié en 1972. Qualifié par Derk Mahon « d'œuvre riche et complexe par le meilleur poète irlandais de sa génération », The Rough Field est composé de dizaines de poèmes variés de par leur style, leur longueur et leur tonalité. Tantôt basés sur l'imprévisible et la pure juxtaposition, tantôt suivant un thème logique et cohérent, les poèmes retracent la jeunesse de l'auteur en Ulster sur le terrain d'un milieu rural condamné à vite disparaître et de l'histoire tragique d'Irlande.Le garbh acaidh, métaphore omniprésente dans les poèmes, est le nom gaélique du hameau où a grandi Montague que l'on traduit généralement par« la terre » ou « le champ en friche ». Cette métaphore établit un lien significatif entre le récit apparemment personnel du livre et l'histoire de la province de l'Ulster, ce Nord politiquement brisé, qui se meurt, stérile et marqué à jamais par les fractures politiques ; Dans The Rough Field il accumule des procédés différents et utilise souvent le collage en citant les sources historiques ou politiques diverses et en introduisant différentes langues, différents registres, différents niveaux de diction et différentes formes poétiques pour parvenir à la représentation de l'image complexe et émouvante d'une province déchirée d'une nation divisée, ce « paysage rude qui me hante ».In 1972 John Montague published his monumental The Rough Field, a long poetic sequence of varying styles and voices called by Derek Mahon « a rich and complex work by the best poet of his generation. » Functioning as much by surprise and sharp juxtaposition a as by coherent thematic development, the poems of The Rough Field examine an upbringing in a rapidly disappearing rural Ulster played out on the disappointing terrain of Irish history, its sad harvests little more than recurring betrayal and division.The guiding metaphor of The Rough Field is the

  4. Laser assisted fabrication of random rough surfaces for optoelectronics

    Energy Technology Data Exchange (ETDEWEB)

    Brissonneau, V., E-mail: vincent.brissonneau@im2np.fr [Thales Optronique SA, Avenue Gay-Lussac, 78995 Elancourt (France); Institut Materiaux Microelectronique Nanosciences de Provence, Aix Marseille Universite, Avenue Escadrille Normandie Niemen, 13397 Marseille (France); Escoubas, L. [Institut Materiaux Microelectronique Nanosciences de Provence, Aix Marseille Universite, Avenue Escadrille Normandie Niemen, 13397 Marseille (France); Flory, F. [Institut Materiaux Microelectronique Nanosciences de Provence, Ecole Centrale Marseille, Marseille (France); Berginc, G. [Thales Optronique SA, Avenue Gay-Lussac, 78995 Elancourt (France); Maire, G.; Giovannini, H. [Institut Fresnel, Aix Marseille Universite, Avenue Escadrille Normandie Niemen, 13397 Marseille (France)

    2012-09-15

    Highlights: Black-Right-Pointing-Pointer Random rough surfaces are photofabricated using an argon ion laser. Black-Right-Pointing-Pointer Speckle and surface correlation function are linked. Black-Right-Pointing-Pointer Exposure beam is modified allowing tuning the correlation. Black-Right-Pointing-Pointer Theoretical examples are presented. Black-Right-Pointing-Pointer Experimental results are compared with theoretical expectation. - Abstract: Optical surface structuring shows great interest for antireflective or scattering properties. Generally, fabricated surface structures are periodical but random surfaces that offer new degrees of freedom and possibilities by the control of their statistical properties. We propose an experimental method to create random rough surfaces on silicon by laser processing followed by etching. A photoresist is spin coated onto a silicon substrate and then exposed to the scattering of a modified laser beam. The beam modification is performed by using a micromirror matrix allowing laser beam shaping. An example of tuning is presented. An image composed of two white circles with a black background is displayed and the theoretical shape of the correlation is calculated. Experimental surfaces are elaborated and the correlation function calculated from height mapping. We finally compared the experimental and theoretical correlation functions.

  5. Rough case-based reasoning system for continues casting

    Science.gov (United States)

    Su, Wenbin; Lei, Zhufeng

    2018-04-01

    The continuous casting occupies a pivotal position in the iron and steel industry. The rough set theory and the CBR (case based reasoning, CBR) were combined in the research and implementation for the quality assurance of continuous casting billet to improve the efficiency and accuracy in determining the processing parameters. According to the continuous casting case, the object-oriented method was applied to express the continuous casting cases. The weights of the attributes were calculated by the algorithm which was based on the rough set theory and the retrieval mechanism for the continuous casting cases was designed. Some cases were adopted to test the retrieval mechanism, by analyzing the results, the law of the influence of the retrieval attributes on determining the processing parameters was revealed. A comprehensive evaluation model was established by using the attribute recognition theory. According to the features of the defects, different methods were adopted to describe the quality condition of the continuous casting billet. By using the system, the knowledge was not only inherited but also applied to adjust the processing parameters through the case based reasoning method as to assure the quality of the continuous casting and improve the intelligent level of the continuous casting.

  6. Impact of small-scale geometric roughness on wetting behavior.

    Science.gov (United States)

    Kumar, Vaibhaw; Errington, Jeffrey R

    2013-09-24

    We examine the extent to which small-scale geometric substrate roughness influences the wetting behavior of fluids at solid surfaces. Molecular simulation is used to construct roughness wetting diagrams wherein the progression of the contact angle is traced from the Cassie to Wenzel to impregnation regime with increasing substrate strength for a collection of systems with rectangularly shaped grooves. We focus on the evolution of these diagrams as the length scale of the substrate features approaches the size of a fluid molecule. When considering a series of wetting diagrams for substrates with fixed shape and variable feature periodicity, we find that the diagrams progressively shift away from a common curve as the substrate features become smaller than approximately 10 fluid diameters. It is at this length scale that the macroscopic models of Cassie and Wenzel become unreliable. Deviations from the macroscopic models are attributed to the manner in which the effective substrate-fluid interaction strength evolves with periodicity and the important role that confinement effects play for substrates with small periodicities.

  7. Profilometry of thin films on rough substrates by Raman spectroscopy

    KAUST Repository

    Ledinský, Martin

    2016-12-06

    Thin, light-absorbing films attenuate the Raman signal of underlying substrates. In this article, we exploit this phenomenon to develop a contactless thickness profiling method for thin films deposited on rough substrates. We demonstrate this technique by probing profiles of thin amorphous silicon stripes deposited on rough crystalline silicon surfaces, which is a structure exploited in high-efficiency silicon heterojunction solar cells. Our spatially-resolved Raman measurements enable the thickness mapping of amorphous silicon over the whole active area of test solar cells with very high precision; the thickness detection limit is well below 1 nm and the spatial resolution is down to 500 nm, limited only by the optical resolution. We also discuss the wider applicability of this technique for the characterization of thin layers prepared on Raman/photoluminescence-active substrates, as well as its use for single-layer counting in multilayer 2D materials such as graphene, MoS2 and WS2.

  8. Profilometry of thin films on rough substrates by Raman spectroscopy

    KAUST Repository

    Ledinský , Martin; Paviet-Salomon, Bertrand; Vetushka, Aliaksei; Geissbü hler, Jonas; Tomasi, Andrea; Despeisse, Matthieu; De Wolf, Stefaan; Ballif  , Christophe; Fejfar, Antoní n

    2016-01-01

    Thin, light-absorbing films attenuate the Raman signal of underlying substrates. In this article, we exploit this phenomenon to develop a contactless thickness profiling method for thin films deposited on rough substrates. We demonstrate this technique by probing profiles of thin amorphous silicon stripes deposited on rough crystalline silicon surfaces, which is a structure exploited in high-efficiency silicon heterojunction solar cells. Our spatially-resolved Raman measurements enable the thickness mapping of amorphous silicon over the whole active area of test solar cells with very high precision; the thickness detection limit is well below 1 nm and the spatial resolution is down to 500 nm, limited only by the optical resolution. We also discuss the wider applicability of this technique for the characterization of thin layers prepared on Raman/photoluminescence-active substrates, as well as its use for single-layer counting in multilayer 2D materials such as graphene, MoS2 and WS2.

  9. Effect of seabed roughness on tidal current turbines

    Science.gov (United States)

    Gupta, Vikrant; Wan, Minping

    2017-11-01

    Tidal current turbines are shown to have potential to generate clean energy for a negligible environmental impact. These devices, however, operate in high to moderate current regions where the flow is highly turbulent. It has been shown in flume tank experiments at IFREMER in Boulogne-Sur-Mer (France) and NAFL in the University of Minnesota (US) that the level of turbulence and boundary layer profile affect a turbine's power output and wake characteristics. A major factor that determines these marine flow characteristics is the seabed roughness. Experiments, however, cannot simulate the high Reynolds number conditions of real marine flows. For that, we rely on numerical simulations. High accuracy numerical methods, such as DNS, of wall-bounded flows are very expensive, where the number of grid-points needed to resolve the flow varies as (Re) 9 / 4 (where Re is the flow Reynolds number). While numerically affordable RANS methods compromise on accuracy. Wall-modelled LES methods, which provide both accuracy and affordability, have been improved tremendously in the recent years. We discuss the application of such numerical methods for studying the effect of seabed roughness on marine flow features and their impact on turbine power output and wake characteristics. NSFC, Project Number 11672123.

  10. Effects of confinement & surface roughness in electrorheological flows

    Science.gov (United States)

    Helal, Ahmed; Telleria, Maria J.; Wang, Julie; Strauss, Marc; Murphy, Mike; McKinley, Gareth; Hosoi, A. E.

    2014-11-01

    Electrorheological (ER) fluids are dielectric suspensions that exhibit a fast, reversible change in rheological properties with the application of an external electric field. Upon the application of the electric field, the material develops a field-dependent yield stress that is typically modeled using a Bingham plastic model. ER fluids are promising for designing small, cheap and rapidly actuated hydraulic devices such as rapidly-switchable valves, where fluid flowing in a microchannel can be arrested by applying an external electric field. In the lubrication limit, for a Bingham plastic fluid, the maximum pressure the channel can hold, before yielding, is a function of the field-dependent yield stress, the length of the channel and the electrode gap. In practice, the finite width of the channel and the surface roughness of the electrodes could affect the maximum yield pressure but a quantitative understanding of these effects is currently lacking. In this study, we experimentally investigate the effects of the channel aspect ratio (width/height) and the effects of electrode roughness on the performance of ER valves. Based on this quantitative analysis, we formulate new performance metrics for ER valves as well as design rules for ER valves that will help guide and optimize future designs.

  11. Perceived floor slipperiness and floor roughness in a gait experiment.

    Science.gov (United States)

    Yu, Ruifeng; Li, Kai Way

    2015-01-01

    Slips and falls contribute to occupational injuries and fatalities globally. Both floor slipperiness and floor roughness affect the occurrence of slipping and falling. Investigations on fall-related phenomena are important for the safety and health of workers. The purposes of this study were to: compare the perceived floor slipperiness before and after walking on the floor; compare the perceived floor slipperiness with and without shoes for males and females; discuss the perceived floor roughness based on barefoot walking; and establish regression models to describe the relationship between perceived floor slipperiness and actual friction of the floors. Male and female subjects walked on 3 m walkways with or without shoes. The perceived floor slipperiness ratings both before and after their walk were collected. The perceived floor slipperiness both before and after walking were significantly affected by both floor and surface conditions. Gender, floor, surface, and footwear conditions were all significant factors affecting the adjustment of perceived floor slipperiness. The subjects made more adjustment on perceived floor slipperiness rating when they had shoes on than when they were barefooted. Regression models were established to describe the relationship between perceived floor slipperiness and floor coefficient of friction. These models may be used to estimate perceived floor slipperiness, or in reverse, the coefficient of friction of the floor, so as to prevent slipping and falling in workplaces.

  12. Modeling of the rough spherical nanoparticles manipulation on a substrate based on the AFM nanorobot

    Science.gov (United States)

    Zakeri, M.; Faraji, J.

    2014-12-01

    In this paper, dynamic behavior of the rough spherical micro/nanoparticles during pulling/pushing on the flat substrate has been investigated and analyzed. For this purpose, at first, two hexagonal roughness models (George and Cooper) were studied and then evaluations for adhesion force were determined for rough particle manipulation on flat substrate. These two models were then changed by using of the Rabinovich theory. Evaluations were determined for contact adhesion force between rough particle and flat substrate; depth of penetration evaluations were determined by the Johnson-Kendall-Roberts contact mechanic theory and the Schwartz method and according to Cooper and George roughness models. Then, the novel contact theory was used to determine a dynamic model for rough micro/nanoparticle manipulation on flat substrate. Finally, simulation of particle dynamic behavior was implemented during pushing of rough spherical gold particles with radii of 50, 150, 400, 600, and 1,000 nm. Results derived from simulations of particles with several rates of roughness on flat substrate indicated that compared to results for flat particles, inherent roughness on particles might reduce the rate of critical force needed for sliding and rolling given particles. Given a fixed radius for roughness value and increased roughness height, evaluations for sliding and rolling critical forces showed greater reduction. Alternately, the rate of critical force was shown to reduce relative to an increased roughness radius. With respect to both models, based on the George roughness model, the predicted rate of adhesion force was greater than that determined in the Cooper roughness model, and as a result, the predicted rate of critical force based on the George roughness model was closer to the critical force value of flat particle.

  13. On the nature of surface roughness with application to contact mechanics, sealing, rubber friction and adhesion

    International Nuclear Information System (INIS)

    Persson, B N J; Albohr, O; Tartaglino, U; Volokitin, A I; Tosatti, E

    2005-01-01

    Surface roughness has a huge impact on many important phenomena. The most important property of rough surfaces is the surface roughness power spectrum C(q). We present surface roughness power spectra of many surfaces of practical importance, obtained from the surface height profile measured using optical methods and the atomic force microscope. We show how the power spectrum determines the contact area between two solids. We also present applications to sealing, rubber friction and adhesion for rough surfaces, where the power spectrum enters as an important input. (topical review)

  14. The VHCF experimental investigation of FV520B-I with surface roughness Ry

    Science.gov (United States)

    Wang, J. L.; Zhang, Y. L.; Ding, M. C.; Zhao, Q. C.

    2018-05-01

    Different surface roughness type (Ra and Ry) has different effect on the VHCF failure and life. Ra is widely employed as the quantitative expression of the surface roughness, but there are few fatigue failure mechanism analysis and experimental study under surface roughness Ry. The VHCF experiment is conducted out using the specimen with different surface roughness values. The surface roughness Ry is employed as the major research object to investigate the relationship and distribution tendency between the Ry, fatigue life and the distance between internal inclusion and surface, and a new VHCF failure character is proposed.

  15. Effects of irregular two-dimensional and three-dimensional surface roughness in turbulent channel flows

    International Nuclear Information System (INIS)

    De Marchis, M.; Napoli, E.

    2012-01-01

    Highlights: ► 3D irregular rough surfaces produce higher effects than those observed over 2D. ► Effective slope is a geometrical parameter representative of the roughness effects. ► 3D rough surfaces enhance the turbulence isotropization. ► 2D and 3D irregular roughness partially support the wall similarity. ► Irregular rough surfaces shear some features with regular rough walls. - Abstract: Wall-resolved Large Eddy Simulation of fully developed turbulent channel flows over two different rough surfaces is performed to investigate on the effects of irregular 2D and 3D roughness on the turbulence. The two geometries are obtained through the superimposition of sinusoidal functions having random amplitudes and different wave lengths. In the 2D configuration the irregular shape in the longitudinal direction is replicated in the transverse one, while in the 3D case the sinusoidal functions are generated both in streamwise and spanwise directions. Both channel walls are roughened in such a way as to obtain surfaces with statistically equivalent roughness height, but different shapes. In order to compare the turbulence properties over the two rough walls and to analyse the differences with a smooth wall, the simulations are performed at the same Reynolds number Re τ = 395. The same mean roughness height h = 0.05δ (δ the half channel height) is used for the rough walls. The roughness function obtained with the 3D roughness is larger than in the 2D case, although the two walls share the same mean height. Thus, the considered irregular 3D roughness is more effective in reducing the flow velocity with respect to the 2D roughness, coherently with the literature results that identified a clear dependence of the roughness function on the effective slope (see ), higher in the generated 3D rough wall. The analysis of higher-order statistics shows that the effects of the roughness, independently on its two- or three-dimensional shape, are mainly confined in the inner

  16. Development of techniques for storing rough rice in cold regions, 1: Storage of rough rice at country elevator with natural heat radiation in winter

    International Nuclear Information System (INIS)

    Takekura, K.; Kawamura, S.; Itoh, K.

    2003-01-01

    An on-farm experiment in which 361 metric tons of rough rice was stored in a silo from November until July was conducted at a country elevator in Hokkaido to develop new techniques for storing rough rice in cold regions. The temperature of the rough rice near the inner silo wall decreased to below ice point (-5°C) due to natural heat radiation in winter, which the temperature of the rough rice in the center of the silo was maintained at almost the same temperature as that at the beginning of storage (5°C). Ventilation in the upper vacant space of the silo prevented moisture condensation on the inside surface of the silo during storage. When the cold rough rice was unloaded from the silo in summer, an unheated forced-air drier was used to increase the temperature of rough rice to above the dew point temperature of surrounding air. During the unloading and rewarming process, the moisture content of the rough rice increased due to moisture condensation on the grain from the air. However, the husks first absorbed the condensation and then the moisture slowly permeated into the brown rice kernel. Thus the rewarming process didn't cause any fissures in the brown rice. The results of the experiment indicate that condensation on rough rice doesn't give rise to any problems

  17. Effect of surface roughness and Reynolds number on compressor cascade performance

    International Nuclear Information System (INIS)

    Back, Seung Chul; Song, Seung Jin

    2009-01-01

    An experimental work has been conducted in a linear compressor cascade to find out the effect of surface roughness and Reynolds number. Surveys were conducted with different roughness size and Reynolds number. The k s /c value of each roughness is 0.0006, 0.0090, 0.00150, 0.00213, and 0.00425. The range of Reynolds number is 300,000∼600,000 and conducted with roughened blade, which roughness Ra is 2.89 microns. Flow pressure, velocity, and angle have been found out via 5 hole probe. Pressure loss and deviation increased with increasing roughness. In the low Reynolds number under 500,000, tested roughness does not affect to the performance of compressor cascade. However, roughness is very sensitive to pressure loss in high Reynolds number over 550,000.

  18. Bidirectional reflectance distribution function modeling of one-dimensional rough surface in the microwave band

    International Nuclear Information System (INIS)

    Guo Li-Xin; Gou Xue-Yin; Zhang Lian-Bo

    2014-01-01

    In this study, the bidirectional reflectance distribution function (BRDF) of a one-dimensional conducting rough surface and a dielectric rough surface are calculated with different frequencies and roughness values in the microwave band by using the method of moments, and the relationship between the bistatic scattering coefficient and the BRDF of a rough surface is expressed. From the theory of the parameters of the rough surface BRDF, the parameters of the BRDF are obtained using a genetic algorithm. The BRDF of a rough surface is calculated using the obtained parameter values. Further, the fitting values and theoretical calculations of the BRDF are compared, and the optimization results are in agreement with the theoretical calculation results. Finally, a reference for BRDF modeling of a Gaussian rough surface in the microwave band is provided by the proposed method. (electromagnetism, optics, acoustics, heat transfer, classical mechanics, and fluid dynamics)

  19. Analysis of the coherent and turbulent stresses of a numerically simulated rough wall pipe

    Science.gov (United States)

    Chan, L.; MacDonald, M.; Chung, D.; Hutchins, N.; Ooi, A.

    2017-04-01

    A turbulent rough wall flow in a pipe is simulated using direct numerical simulation (DNS) where the roughness elements consist of explicitly gridded three-dimensional sinusoids. Two groups of simulations were conducted where the roughness semi-amplitude h+ and the roughness wavelength λ+ are systematically varied. The triple decomposition is applied to the velocity to separate the coherent and turbulent components. The coherent or dispersive component arises due to the roughness and depends on the topological features of the surface. The turbulent stress on the other hand, scales with the friction Reynolds number. For the case with the largest roughness wavelength, large secondary flows are observed which are similar to that of duct flows. The occurrence of these large secondary flows is due to the spanwise heterogeneity of the roughness which has a spacing approximately equal to the boundary layer thickness δ.

  20. The need for LWR metrology standardization: the imec roughness protocol

    Science.gov (United States)

    Lorusso, Gian Francesco; Sutani, Takumichi; Rutigliani, Vito; van Roey, Frieda; Moussa, Alain; Charley, Anne-Laure; Mack, Chris; Naulleau, Patrick; Constantoudis, Vassilios; Ikota, Masami; Ishimoto, Toru; Koshihara, Shunsuke

    2018-03-01

    As semiconductor technology keeps moving forward, undeterred by the many challenges ahead, one specific deliverable is capturing the attention of many experts in the field: Line Width Roughness (LWR) specifications are expected to be less than 2nm in the near term, and to drop below 1nm in just a few years. This is a daunting challenge and engineers throughout the industry are trying to meet these targets using every means at their disposal. However, although current efforts are surely admirable, we believe they are not enough. The fact is that a specification has a meaning only if there is an agreed methodology to verify if the criterion is met or not. Such a standardization is critical in any field of science and technology and the question that we need to ask ourselves today is whether we have a standardized LWR metrology or not. In other words, if a single reference sample were provided, would everyone measuring it get reasonably comparable results? We came to realize that this is not the case and that the observed spread in the results throughout the industry is quite large. In our opinion, this makes the comparison of LWR data among institutions, or to a specification, very difficult. In this paper, we report the spread of measured LWR data across the semiconductor industry. We investigate the impact of image acquisition, measurement algorithm, and frequency analysis parameters on LWR metrology. We review critically some of the International Technology Roadmap for Semiconductors (ITRS) metrology guidelines (such as measurement box length larger than 2μm and the need to correct for SEM noise). We compare the SEM roughness results to AFM measurements. Finally, we propose a standardized LWR measurement protocol - the imec Roughness Protocol (iRP) - intended to ensure that every time LWR measurements are compared (from various sources or to specifications), the comparison is sensible and sound. We deeply believe that the industry is at a point where it is

  1. Observations of Seafloor Roughness in a Tidally Modulated Inlet

    Science.gov (United States)

    Lippmann, T. C.; Hunt, J.

    2014-12-01

    The vertical structure of shallow water flows are influenced by the presence of a bottom boundary layer, which spans the water column for long period waves or mean flows. The nature of the boundary is determined in part by the roughness elements that make up the seafloor, and includes sometimes complex undulations associated with regular and irregular shaped bedforms whose scales range several orders of magnitude from orbital wave ripples (10-1 m) to mega-ripples (100 m) and even larger features (101-103) such as sand waves, bars, and dunes. Modeling efforts often parameterize the effects of roughness elements on flow fields, depending on the complexity of the boundary layer formulations. The problem is exacerbated by the transient nature of bedforms and their large spatial extent and variability. This is particularly important in high flow areas with large sediment transport, such as tidally dominated sandy inlets like New River Inlet, NC. Quantification of small scale seafloor variability over large spatial areas requires the use of mobile platforms that can measure with fine scale (order cm) accuracy in wide swaths. The problem is difficult in shallow water where waves and currents are large, and water clarity is often limited. In this work, we present results from bathymetric surveys obtained with the Coastal Bathymetry Survey System, a personal watercraft equipped with a Imagenex multibeam acoustic echosounder and Applanix POS-MV 320 GPS-aided inertial measurement unit. This system is able to measure shallow water seafloor bathymetry and backscatter intensity with very fine scale (10-1 m) resolution and over relatively large scales (103 m) in the presence of high waves and currents. Wavenumber spectra show that the noise floor of the resolved multibeam bathymetry is on the order of 2.5 - 5 cm in amplitude, depending on water depths ranging 2 - 6 m, and about 30 cm in wavelength. Seafloor roughness elements are estimated from wavenumber spectra across the inlet

  2. Investigation of surface roughness on etched glass surfaces

    International Nuclear Information System (INIS)

    Papa, Z.; Budai, J.; Farkas, B.; Toth, Z.

    2011-01-01

    Roughening the surface of solar cells is a common practice within the photovoltaic industry as it reduces reflectance, and thus enhances the performance of devices. In this work the relationship between reflectance characterized by the haze parameter, surface roughness and optical properties was investigated. To achieve this goal, model samples were prepared by hydrofluoric acid etching of glass for various times and measured by optical microscopy, spectroscopic ellipsometry, scanning electron microscopy, and atomic force microscopy. Our investigation showed that the surface reflectance was decreased not only by the roughening of the surface but also by the modification of the depth profile and lowering of the refractive index of the surface domain of the samples.

  3. Effect of inclusion density on ductile fracture toughness and roughness

    DEFF Research Database (Denmark)

    Srivastava, Akhilesh Kumar; Ponson, L.; Osovski, S.

    2014-01-01

    Three dimensional calculations of ductile fracture under mode I plane strain, small scale yielding conditions are carried out using an elastic-viscoplastic constitutive relation for a progressively cavitating solid with two populations of void nucleating second phase particles. Larger inclusions...... that result in void nucleation at an early stage are modeled discretely while smaller particles that require large strains to nucleate voids are homogeneously distributed. Full field solutions are obtained for eight volume fractions, ranging from 1% to 19%, of randomly distributed larger inclusions. For each...... volume fraction calculations are carried out for seven random distributions of inclusion centers. Crack growth resistance curves and fracture surface roughness statistics are calculated using standard procedures. The crack growth resistance is characterized in terms of both JIC and the tearing modulus TR...

  4. Long charged macromolecule in an entropic trap with rough surfaces.

    Science.gov (United States)

    Mamasakhlisov, Yevgeni Sh; Hayryan, Shura; Hu, Chin-Kun

    2012-11-01

    The kinetics of the flux of a charged macromolecular solution through an environment of changing geometry with wide and constricted regions is investigated analytically. A model device consisting of alternating deep and shallow slits known as an "entropic trap" is used to represent the environment. The flux is supported by the external electrostatic field. The "wormlike chain" model is used for the macromolecule (dsDNA in the present study). The chain entropy in both the deep and the shallow slits, the work by the electric field, and the energy of the elastic bending of the chain are taken into account accurately. Based on the calculated free energy, the kinetics and the scaling behavior of the chain escaping from the entropic trap are studied. We find that the escape process occurs in two kinetic stages with different time scales and discuss the possible influence of the surface roughness. The scope of the accuracy of the proposed model is discussed.

  5. Preference Mining Using Neighborhood Rough Set Model on Two Universes.

    Science.gov (United States)

    Zeng, Kai

    2016-01-01

    Preference mining plays an important role in e-commerce and video websites for enhancing user satisfaction and loyalty. Some classical methods are not available for the cold-start problem when the user or the item is new. In this paper, we propose a new model, called parametric neighborhood rough set on two universes (NRSTU), to describe the user and item data structures. Furthermore, the neighborhood lower approximation operator is used for defining the preference rules. Then, we provide the means for recommending items to users by using these rules. Finally, we give an experimental example to show the details of NRSTU-based preference mining for cold-start problem. The parameters of the model are also discussed. The experimental results show that the proposed method presents an effective solution for preference mining. In particular, NRSTU improves the recommendation accuracy by about 19% compared to the traditional method.

  6. Effects of Roughness and Inertia on Precursors to Frictional Sliding

    Science.gov (United States)

    Robbins, Mark O.; Salerno, K. Michael

    2012-02-01

    Experiments show that when a PMMA block on a surface is normally loaded and driven by an external shear force, contact at the interface is modified in discrete precursor slips prior to steady state sliding.[1] Our simulations use an atomistic model of a rough two-dimensional block in contact with a flat surface to investigate the evolution of stress and displacement along the contact between surfaces. The talk will show how local and global stress conditions govern the initiation of interfacial cracks as well as the spatial extension of the cracked region. Inertia also plays an important role in determining the number and size of slips before sliding and influences the distribution of stresses at the interface. Finally, the geometry of surface asperities also influences the interfacial evolution and the total friction force. The relationship between the interfacial stress state and rupture velocity will also be discussed. [1] S.M. Rubinstein, G. Cohen and J. Fineberg, PRL 98, 226103 (2007)

  7. Turbulent water flow over rough bed - part I

    Energy Technology Data Exchange (ETDEWEB)

    Ksiazek, Leszek; Bartnik, Wojciech; Rumian, Jacek; Zagorowski, Pawel, E-mail: rmksiaze@cyf-kr.edu.pl [Department of Hydraulic Engineering and Geotechnics, University of Agriculture in Krakow, Mickiewicza Avenue 24/28, 30-059 Krakow (Poland)

    2011-12-22

    Restitution of diadromic fish requires restoration of ecological continuity of watercourses, e.g. by building fish ladders. Directions for fish ladders require that ichthyofauna is granted accurate conditions of water flow. To describe them, average values are used, that do not convey e.g. turbulence intensity or its spatial differentiation. The paper presents results of research on the turbulent water flow over the rough bed. The measurements were carried out with high sampling frequency probe for three velocity components. Bed configuration, distribution of average velocities and turbulence intensity were defined. The range of bed influence for the discussed water flow conditions was ascertained to reach the maximum of about 0.25 of height and decline at 0.35. The lowest turbulence and relatively lowest velocities near the bed may promote successive stages of ichthyofauna development.

  8. Rough and Tumble” Play: Lessons in Life

    Directory of Open Access Journals (Sweden)

    Pam Jarvis

    2006-01-01

    Full Text Available This paper focuses upon the developmental role of Rough and Tumble (R&T play with particular attention to the narratives that children use to underpin such activities, and to gender differences within these. The empirical research focused upon the R&T play of children in the early years department of a suburban primary school in Northern England. The children's playtime activities were ethnographically observed over a period of eighteen calendar months, encompassing five school terms. The effects of evolution, biology and culture are recognized in the approach taken to the analysis of data. Findings indicated that the narratives underpinning R&T play were socially complex and highly gendered, and that mixed gender R&T play in particular could be theorized to mirror and simplify aspects of complex, gendered adult interaction.

  9. Optical scattering from rough-rolled aluminum surfaces.

    Science.gov (United States)

    Rönnelid, M; Adsten, M; Lindström, T; Nostell, P; Wäckelgård, E

    2001-05-01

    Bidirectional, angular resolved scatterometry was used to evaluate the feasibility of using rolled aluminum as reflectors in solar thermal collectors and solar cells. Two types of rolled aluminum with different surface roughnesses were investigated. The results show that the smoother of the two samples [rms height, (0.20 ? 0.02) mum] can be used as a nonimaging, concentrating reflector with moderate reflection losses compared with those of optically smooth aluminum reflectors. The sample with the rougher surface [rms height, (0.6 ? 0.1) mum] is not suitable as a concentrating element but can be used as planar reflectors. The orientation of the rolling grooves is then of importance for minimizing reflection losses in the system.

  10. Growth of contact area between rough surfaces under normal stress

    Science.gov (United States)

    Stesky, R. M.; Hannan, S. S.

    1987-05-01

    The contact area between deforming rough surfaces in marble, alabaster, and quartz was measured from thin sections of surfaces bonded under load with low viscosity resin epoxy. The marble and alabaster samples had contact areas that increased with stress at an accelerating rate. This result suggests that the strength of the asperity contacts decreased progressively during the deformation, following some form of strain weakening relationship. This conclusion is supported by petrographic observation of the thin sections that indicate that much of the deformation was cataclastic, with minor twinning of calcite and kinking of gypsum. In the case of the quartz, the observed contact area was small and increased approximately linearly with normal stress. Only the irreversible cataclastic deformation was observed; however strain-induced birefringence and cracking of the epoxy, not observed with the other rocks, suggests that significant elastic deformation occurred, but recovered during unloading.

  11. Surface roughness effects on blister formation in polycrystalline molybdenum

    International Nuclear Information System (INIS)

    Saidoh, Masahiro; Sone, Kazuho; Yamada, Rayji; Ohtsuka, Hidewo; Murakami, Yoshio

    1977-07-01

    Polycrystalline molybdenum targets with electropolished and roughened surfaces were bombarded with 100 keV He + and 200 keV H 2 + ions at room temperature. It has been demonstrated that the blister formation is largely or completely suppressed by roughening the electropolished surface with emery paper of No. 1200, No. 400 and No. 100. Up to a He + fluence of 1.0 x 10 19 particles/cm 2 , no blisters are observed in the targets with the two roughest surfaces, while on the smooth surface blisters begin to occur at a fluence of 7.5 x 10 17 particles/cm 2 . The surface roughness effect on blister suppression is discussed in relation to the projected range of incident particles. (auth.)

  12. Surface forces between rough and topographically structured interfaces

    DEFF Research Database (Denmark)

    Thormann, Esben

    2017-01-01

    Within colloidal science, direct or indirect measurements of surface forces represent an important tool for developing a fundamental understanding of colloidal systems, as well as for predictions of the stability of colloidal suspensions. While the general understanding of colloidal interactions...... and manufactured materials, which possess topographical variations. Further, with technological advances in nanotechnology, fabrication of nano- or micro-structured surfaces has become increasingly important for many applications, which calls for a better understanding of the effect of surface topography...... on the interaction between interfaces. This paper presents a review of the current state of understanding of the effect of surface roughness on DLVO forces, as well as on the interactions between topographically structured hydrophobic surfaces in water. While the first case is a natural choice because it represents...

  13. Rough set and rule-based multicriteria decision aiding

    Directory of Open Access Journals (Sweden)

    Roman Slowinski

    2012-08-01

    Full Text Available The aim of multicriteria decision aiding is to give the decision maker a recommendation concerning a set of objects evaluated from multiple points of view called criteria. Since a rational decision maker acts with respect to his/her value system, in order to recommend the most-preferred decision, one must identify decision maker's preferences. In this paper, we focus on preference discovery from data concerning some past decisions of the decision maker. We consider the preference model in the form of a set of "if..., then..." decision rules discovered from the data by inductive learning. To structure the data prior to induction of rules, we use the Dominance-based Rough Set Approach (DRSA. DRSA is a methodology for reasoning about data, which handles ordinal evaluations of objects on considered criteria and monotonic relationships between these evaluations and the decision. We review applications of DRSA to a large variety of multicriteria decision problems.

  14. Numerical modelling of flow and transport in rough fractures

    Directory of Open Access Journals (Sweden)

    Scott Briggs

    2014-12-01

    Full Text Available Simulation of flow and transport through rough walled rock fractures is investigated using the lattice Boltzmann method (LBM and random walk (RW, respectively. The numerical implementation is developed and validated on general purpose graphic processing units (GPGPUs. Both the LBM and RW method are well suited to parallel implementation on GPGPUs because they require only next-neighbour communication and thus can reduce expenses. The LBM model is an order of magnitude faster on GPGPUs than published results for LBM simulations run on modern CPUs. The fluid model is verified for parallel plate flow, backward facing step and single fracture flow; and the RW model is verified for point-source diffusion, Taylor-Aris dispersion and breakthrough behaviour in a single fracture. Both algorithms place limitations on the discrete displacement of fluid or particle transport per time step to minimise the numerical error that must be considered during implementation.

  15. Reducing surface roughness by optimising the turning parameters

    Directory of Open Access Journals (Sweden)

    Senthil Kumar, K.

    2013-08-01

    Full Text Available Modern manufacturers worldwide look for the cheapest quality-manufactured machined components to compete in the market. Good surface quality is desired for the proper functioning of the parts produced. The surface quality is influenced by the cutting speed, feed rate, depth of cut, and many other parameters. In this paper, the Taguchi method a powerful tool to design optimisation for quality is used to find the optimal machining parameters for the turning operation. An orthogonal array, the signal-to-noise (S/N ratio, and the analysis of variance (ANOVA are employed to investigate the machining characteristics of super duplex stainless steel bars using uncoated carbide cutting tools. The effect of machining parameters on surface roughness was discovered. Confirmation tests were conducted at optimal conditions to compare the experimental results with the predicted values.

  16. The Effect of Volumetric Porosity on Roughness Element Drag

    Science.gov (United States)

    Gillies, John; Nickling, William; Nikolich, George; Etyemezian, Vicken

    2016-04-01

    Much attention has been given to understanding how the porosity of two dimensional structures affects the drag force exerted by boundary-layer flow on these flow obstructions. Porous structures such as wind breaks and fences are typically used to control the sedimentation of sand and snow particles or create micro-habitats in their lee. Vegetation in drylands also exerts control on sediment transport by wind due to aerodynamic effects and interaction with particles in transport. Recent research has also demonstrated that large spatial arrays of solid three dimensional roughness elements can be used to reduce sand transport to specified targets for control of wind erosion through the effect of drag partitioning and interaction of the moving sand with the large (>0.3 m high) roughness elements, but porous elements may improve the effectiveness of this approach. A thorough understanding of the role porosity plays in affecting the drag force on three-dimensional forms is lacking. To provide basic understanding of the relationship between the porosity of roughness elements and the force of drag exerted on them by fluid flow, we undertook a wind tunnel study that systematically altered the porosity of roughness elements of defined geometry (cubes, rectangular cylinders, and round cylinders) and measured the associated change in the drag force on the elements under similar Reynolds number conditions. The elements tested were of four basic forms: 1) same sized cubes with tubes of known diameter milled through them creating three volumetric porosity values and increasing connectivity between the tubes, 2) cubes and rectangular cylinders constructed of brass screen that nested within each other, and 3) round cylinders constructed of brass screen that nested within each other. The two-dimensional porosity, defined as the ratio of total surface area of the empty space to the solid surface area of the side of the element presented to the fluid flow was conserved at 0.519 for

  17. Dry deposition on smooth and rough urban surfaces

    International Nuclear Information System (INIS)

    Roed, J.

    1987-01-01

    Following the Chernobyl accident, dry deposition velocities on smooth surfaces indoors and outdoors have been measured in Denmark. Internal wall surfaces gave deposition velocities of 0.0008-0.0009 cm/s for 131I and 0.0001-0.0002 cm/s for 134Cs and 103Ru. Internal floor surfaces gave higher values for the deposition velocities: for 131I, 0.002 cm/s and for 134Cs and 103Ru, 0.0005-0.0013 cm/s. The deposition velocities on vertical and horizontal external surfaces were nearly equal. Those for 131I were found as 0.02-0.03 cm/s and for 137Cs as 0.001-0.002 cm/s. On external rough surfaces such as grass and corrugated roof material the deposition velocities for 134Cs and 103Ru were 0.03-0.05 cm/s. For iodine, however, deposition velocities were higher for clipped grass (2 cm/s) than for roof material (0.2-0.4 cm/s). The results show that internal deposition velocities are considerably lower than those on external smooth surfaces, and that the deposition velocities on rough surfaces are an order of magnitude higher than on smooth surfaces. It was also shown that the deposition velocities of iodine are considerably higher than those of cesium and ruthenium. This work was supported by EEC Radiation Protection Programme No B16-107-DK and by NKA, The Nordic Liaison Committee for Atomic Energy. (author)

  18. Improvement of PET surface hydrophilicity and roughness through blending

    Energy Technology Data Exchange (ETDEWEB)

    Kolahchi, Ahmad Rezaei; Ajji, Abdellah; Carreau, Pierre J. [CREPEC, Chemical Engineering Department, Polytechnique Montreal, 2500 chemin de Polytechnique, Quebec, Montreal (Canada)

    2015-05-22

    Controlling the adhesion of the polymer surface is a key issue in surface science, since polymers have been a commonly used material for many years. The surface modification in this study includes two different aspects. One is to enhance the hydrophilicity and the other is to create the roughness on the PET film surface. In this study we developed a novel and simple approach to modify polyethylene terephthalate (PET) film surface through polymer blending in twin-screw extruder. One example described in the study uses polyethylene glycol (PEG) in polyethylene terephthalate (PET) host to modify a PET film surface. Low content of polystyrene (PS) as a third component was used in the system to increase the rate of migration of PEG to the surface of the film. Surface enrichment of PEG was observed at the polymer/air interface of the polymer film containing PET-PEG-PS whereas for the PET-PEG binary blend more PEG was distributed within the bulk of the sample. Furthermore, a novel method to create roughness at the PET film surface was proposed. In order to roughen the surface of PET film, a small amount of PKHH phenoxy resin to change PS/PET interfacial tension was used. The compatibility effect of PKHH causes the formation of smaller PS droplets, which were able to migrate more easily through PET matrix. Consequently, resulting in a locally elevated concentration of PS near the surface of the film. The local concentration of PS eventually reached a level where a co-continuous morphology occurred, resulting in theinstabilities on the surface of the film.

  19. Effects of surface roughness and electrokinetic heterogeneity on electroosmotic flow in microchannel

    Energy Technology Data Exchange (ETDEWEB)

    Masilamani, Kannan; Ganguly, Suvankar; Feichtinger, Christian; Bartuschat, Dominik; Rüde, Ulrich, E-mail: suva_112@yahoo.co.in [Department of Computer Science 10 University of Erlangen-Nuremberg, Cauerstr.11 91058 Erlangen (Germany)

    2015-06-15

    In this paper, a hybrid lattice-Boltzmann and finite-difference (LB-FD) model is applied to simulate the effects of three-dimensional surface roughness and electrokinetic heterogeneity on electroosmotic flow (EOF) in a microchannel. The lattice-Boltzmann (LB) method has been employed to obtain the flow field and a finite-difference (FD) method is used to solve the Poisson-Boltzmann (PB) equation for the electrostatic potential distribution. Numerical simulation of flow through a square cross-section microchannel with designed roughness is conducted and the results are critically analysed. The effects of surface heterogeneity on the electroosmotic transport are investigated for different roughness height, width, roughness interval spacing, and roughness surface potential. Numerical simulations reveal that the presence of surface roughness changes the nature of electroosmotic transport through the microchannel. It is found that the electroosmotic velocity decreases with the increase in roughness height and the velocity profile becomes asymmetric. For the same height of the roughness elements, the EOF velocity rises with the increase in roughness width. For the heterogeneously charged rough channel, the velocity profile shows a distinct deviation from the conventional plug-like flow pattern. The simulation results also indicate locally induced flow vortices which can be utilized to enhance the flow and mixing within the microchannel. The present study has important implications towards electrokinetic flow control in the microchannel, and can provide an efficient way to design a microfluidic system of practical interest. (paper)

  20. Effects of surface roughness and film thickness on the adhesion of a bioinspired nanofilm

    Science.gov (United States)

    Peng, Z. L.; Chen, S. H.

    2011-05-01

    Inspired by the gecko's climbing ability, adhesion between an elastic nanofilm with finite length and a rough substrate with sinusoidal roughness is studied in the present paper, considering the effects of substrate roughness and film thickness. It demonstrates that the normal adhesion force of the nanofilm on a rough substrate depends significantly on the geometrical parameters of the substrate. When the film length is larger than the wavelength of the sinusoidal roughness of the substrate, the normal adhesion force decreases with increasing surface roughness, while the normal adhesion force initially decreases then increases if the wavelength of roughness is larger than the film length. This finding is qualitatively consistent with a previously interesting experimental observation in which the adhesion force of the gecko spatula is found to reduce significantly at an intermediate roughness. Furthermore, it is inferred that the gecko may achieve an optimal spatula thickness not only to follow rough surfaces, but also to saturate the adhesion force. The results in this paper may be helpful for understanding how geckos overcome the influence of natural surface roughness and possess such adhesion to support their weights.