WorldWideScience

Sample records for grid friendly appliance

  1. Electrical Grid Stability Enhancement using Smart Home Frequency-response Grid -Friendly Appliance System

    Directory of Open Access Journals (Sweden)

    Muawiya A. Kaigama

    2016-03-01

    Full Text Available Load shedding is a powerful scheme used for corrective and preventive measures; corrective to restore system’s stability and preventive to avoid catastrophic failure. However, the affected end users are deprived of power supply absolutely with no choice. This paper presents the design, development, feasibility and merits of Frequency-response Grid -Friendly Appliance System (FRGFAS in a smart home. FRGFAS is a decentralized Adaptive Load Shaving(ALS device that supports grid’s system stability by sensing grid’s frequency deterioration level and turns ON/OFF loads accordingly. The FRGFAS permits end users to carry out load shaving at their scale of preference in smart homes via flexible demand responses and automates outdoor lighting to optimum operational hours. FRGFAS obviate load shedding by shaving loads whenever the system is in distress and reset loads supply to the normal state when it stabilizes, this Consequently increases the end user comfort zone and averts a blackout.

  2. Pacific Northwest GridWise™ Testbed Demonstration Projects; Part II. Grid Friendly™ Appliance Project

    Energy Technology Data Exchange (ETDEWEB)

    Hammerstrom, Donald J.; Brous, Jerry; Chassin, David P.; Horst, Gale R.; Kajfasz, Robert; Michie, Preston; Oliver, Terry V.; Carlon, Teresa A.; Eustis, Conrad; Jarvegren, Olof M.; Marek, W.; Munson, Ryan L.; Pratt, Robert G.

    2007-10-01

    Fifty residential electric water heaters and 150 new residential clothes dryers were modified to respond to signals received from underfrequency, load-shedding appliance controllers. Each controller monitored the power-grid voltage signal and requested that electrical load be shed by its appliance whenever electric power-grid frequency fell below 59.95 Hz. The controllers and their appliances were installed and monitored for more than a year at residential sites at three locations in Washington and Oregon. The controllers and their appliances responded reliably to each shallow underfrequency event—an average of one event per day—and shed their loads for the durations of these events. Appliance owners reported that the appliance responses were unnoticed and caused little or no inconvenience for the homes’ occupants.

  3. Dynamic Appliances Scheduling in Collaborative MicroGrids System

    Science.gov (United States)

    Bilil, Hasnae; Aniba, Ghassane; Gharavi, Hamid

    2017-01-01

    In this paper a new approach which is based on a collaborative system of MicroGrids (MG’s), is proposed to enable household appliance scheduling. To achieve this, appliances are categorized into flexible and non-flexible Deferrable Loads (DL’s), according to their electrical components. We propose a dynamic scheduling algorithm where users can systematically manage the operation of their electric appliances. The main challenge is to develop a flattening function calculus (reshaping) for both flexible and non-flexible DL’s. In addition, implementation of the proposed algorithm would require dynamically analyzing two successive multi-objective optimization (MOO) problems. The first targets the activation schedule of non-flexible DL’s and the second deals with the power profiles of flexible DL’s. The MOO problems are resolved by using a fast and elitist multi-objective genetic algorithm (NSGA-II). Finally, in order to show the efficiency of the proposed approach, a case study of a collaborative system that consists of 40 MG’s registered in the load curve for the flattening program has been developed. The results verify that the load curve can indeed become very flat by applying the proposed scheduling approach. PMID:28824226

  4. Modeling of GE Appliances in GridLAB-D: Peak Demand Reduction

    Energy Technology Data Exchange (ETDEWEB)

    Fuller, Jason C.; Vyakaranam, Bharat GNVSR; Prakash Kumar, Nirupama; Leistritz, Sean M.; Parker, Graham B.

    2012-04-29

    The widespread adoption of demand response enabled appliances and thermostats can result in significant reduction to peak electrical demand and provide potential grid stabilization benefits. GE has developed a line of appliances that will have the capability of offering several levels of demand reduction actions based on information from the utility grid, often in the form of price. However due to a number of factors, including the number of demand response enabled appliances available at any given time, the reduction of diversity factor due to the synchronizing control signal, and the percentage of consumers who may override the utility signal, it can be difficult to predict the aggregate response of a large number of residences. The effects of these behaviors can be modeled and simulated in open-source software, GridLAB-D, including evaluation of appliance controls, improvement to current algorithms, and development of aggregate control methodologies. This report is the first in a series of three reports describing the potential of GE's demand response enabled appliances to provide benefits to the utility grid. The first report will describe the modeling methodology used to represent the GE appliances in the GridLAB-D simulation environment and the estimated potential for peak demand reduction at various deployment levels. The second and third reports will explore the potential of aggregated group actions to positively impact grid stability, including frequency and voltage regulation and spinning reserves, and the impacts on distribution feeder voltage regulation, including mitigation of fluctuations caused by high penetration of photovoltaic distributed generation and the effects on volt-var control schemes.

  5. Effects of dynamic-demand-control appliances on the power grid frequency

    Science.gov (United States)

    Tchuisseu, E. B. Tchawou; Gomila, D.; Brunner, D.; Colet, P.

    2017-08-01

    Power grid frequency control is a demanding task requiring expensive idle power plants to adapt the supply to the fluctuating demand. An alternative approach is controlling the demand side in such a way that certain appliances modify their operation to adapt to the power availability. This is especially important to achieve a high penetration of renewable energy sources. A number of methods to manage the demand side have been proposed. In this work we focus on dynamic demand control (DDC), where smart appliances can delay their switchings depending on the frequency of the system. We introduce a simple model to study the effects of DDC on the frequency of the power grid. The model includes the power plant equations, a stochastic model for the demand that reproduces, adjusting a single parameter, the statistical properties of frequency fluctuations measured experimentally, and a generic DDC protocol. We find that DDC can reduce small and medium-size fluctuations but it can also increase the probability of observing large frequency peaks due to the necessity of recovering pending task. We also conclude that a deployment of DDC around 30-40% already allows a significant reduction of the fluctuations while keeping the number of pending tasks low.

  6. Powering a Home with Just 25 Watts of Solar PV. Super-Efficient Appliances Can Enable Expanded Off-Grid Energy Service Using Small Solar Power Systems

    Energy Technology Data Exchange (ETDEWEB)

    Phadke, Amol A. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Jacobson, Arne [Schatz Energy Research Center, Arcata, CA (United States); Park, Won Young [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Lee, Ga Rick [Schatz Energy Research Center, Arcata, CA (United States); Alstone, Peter [Univ. of California, Berkeley, CA (United States); Khare, Amit [Schatz Energy Research Center, Arcata, CA (United States)

    2015-04-01

    Highly efficient direct current (DC) appliances have the potential to dramatically increase the affordability of off-grid solar power systems used for rural electrification in developing countries by reducing the size of the systems required. For example, the combined power requirement of a highly efficient color TV, four DC light emitting diode (LED) lamps, a mobile phone charger, and a radio is approximately 18 watts and can be supported by a small solar power system (at 27 watts peak, Wp). Price declines and efficiency advances in LED technology are already enabling rapidly increased use of small off-grid lighting systems in Africa and Asia. Similar progress is also possible for larger household-scale solar home systems that power appliances such as lights, TVs, fans, radios, and mobile phones. When super-efficient appliances are used, the total cost of solar home systems and their associated appliances can be reduced by as much as 50%. The results vary according to the appliances used with the system. These findings have critical relevance for efforts to provide modern energy services to the 1.2 billion people worldwide without access to the electrical grid and one billion more with unreliable access. However, policy and market support are needed to realize rapid adoption of super-efficient appliances.

  7. Renewables-Friendly Grid Development Strategies. Experience in the United States, Potential Lessons for China

    Energy Technology Data Exchange (ETDEWEB)

    Hurlbut, David [National Renewable Energy Lab. (NREL), Golden, CO (United States); Zhou, Ella [National Renewable Energy Lab. (NREL), Golden, CO (United States); Porter, Kevin [Exeter Associates, Columbia, MD (United States); Arent, Douglas J. [Joint Inst. for Strategic Energy Analysis, Golden, CO (United States)

    2015-10-01

    This report aims to help China's reform effort by providing a concise summary of experience in the United States with "renewables-friendly"" grid management, focusing on experiences that might be applicable to China. It focuses on utility-scale renewables and sets aside issues related to distributed generation.

  8. Grid-friendly wind power systems based on the synchronverter technology

    International Nuclear Information System (INIS)

    Zhong, Qing-Chang; Ma, Zhenyu; Ming, Wen-Long; Konstantopoulos, George C.

    2015-01-01

    Highlights: • A grid-friendly wind power system that uses the synchronverter technology is proposed. • Both the rotor-side and the grid-side converters act as synchronverters. • The complete generator–motor–generator system improves the performance under grid faults. • Real-time digital simulation results verify the effectiveness of the proposed method. - Abstract: Back-to-back PWM converters are becoming a realistic alternative to conventional converters in high-power wind power applications. In this paper, a control strategy based on the synchronverter technology is proposed for back-to-back PWM converters. Both converters are run as synchronverters, which are mathematically equivalent to the conventional synchronous generators. The rotor-side converter is responsible for maintaining the DC link voltage and the grid-side converter is responsible for the maximum power point tracking (MPPT). As the two converters are operated using the synchronverter technology, the formed wind power system becomes more friendly to the grid. Extensive real-time digital simulation results are presented to verify the effectiveness of the proposed method under normal operation and grid-fault scenarios

  9. Advanced Grid-Friendly Controls Demonstration Project for Utility-Scale PV Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Gevorgian, Vahan; O' Neill, Barbara

    2016-01-21

    A typical photovoltaic (PV) power plant consists of multiple power electronic inverters and can contribute to grid stability and reliability through sophisticated 'grid-friendly' controls. The availability and dissemination of actual test data showing the viability of advanced utility-scale PV controls among all industry stakeholders can leverage PV's value from being simply an energy resource to providing additional ancillary services that range from variability smoothing and frequency regulation to power quality. Strategically partnering with a selected utility and/or PV power plant operator is a key condition for a successful demonstration project. The U.S. Department of Energy's (DOE's) Solar Energy Technologies Office selected the National Renewable Energy Laboratory (NREL) to be a principal investigator in a two-year project with goals to (1) identify a potential partner(s), (2) develop a detailed scope of work and test plan for a field project to demonstrate the gird-friendly capabilities of utility-scale PV power plants, (3) facilitate conducting actual demonstration tests, and (4) disseminate test results among industry stakeholders via a joint NREL/DOE publication and participation in relevant technical conferences. The project implementation took place in FY 2014 and FY 2015. In FY14, NREL established collaborations with AES and First Solar Electric, LLC, to conduct demonstration testing on their utility-scale PV power plants in Puerto Rico and Texas, respectively, and developed test plans for each partner. Both Puerto Rico Electric Power Authority and the Electric Reliability Council of Texas expressed interest in this project because of the importance of such advanced controls for the reliable operation of their power systems under high penetration levels of variable renewable generation. During FY15, testing was completed on both plants, and a large amount of test data was produced and analyzed that demonstrates the ability of

  10. Neural network algorithm for image reconstruction using the grid friendly projections

    International Nuclear Information System (INIS)

    Cierniak, R.

    2011-01-01

    Full text: The presented paper describes a development of original approach to the reconstruction problem using a recurrent neural network. Particularly, the 'grid-friendly' angles of performed projections are selected according to the discrete Radon transform (DRT) concept to decrease the number of projections required. The methodology of our approach is consistent with analytical reconstruction algorithms. Reconstruction problem is reformulated in our approach to optimization problem. This problem is solved in present concept using method based on the maximum likelihood methodology. The reconstruction algorithm proposed in this work is consequently adapted for more practical discrete fan beam projections. Computer simulation results show that the neural network reconstruction algorithm designed to work in this way improves obtained results and outperforms conventional methods in reconstructed image quality. (author)

  11. Ganga: User-friendly Grid job submission and management tool for LHC and beyond

    International Nuclear Information System (INIS)

    Vanderster, D C; Gaidoz, B; Maier, A; Moscicki, J T; Muraru, A; Brochu, F; Cowan, G; Egede, U; Reece, W; Williams, M; Elmsheuser, J; Harrison, K; Slater, M; Tan, C L; Lee, H C; Liko, D; Pajchel, K; Samset, B; Soroko, A

    2010-01-01

    Ganga has been widely used for several years in ATLAS, LHCb and a handful of other communities. Ganga provides a simple yet powerful interface for submitting and managing jobs to a variety of computing backends. The tool helps users configuring applications and keeping track of their work. With the major release of version 5 in summer 2008, Ganga's main user-friendly features have been strengthened. Examples include a new configuration interface, enhanced support for job collections, bulk operations and easier access to subjobs. In addition to the traditional batch and Grid backends such as Condor, LSF, PBS, gLite/EDG a point-to-point job execution via ssh on remote machines is now supported. Ganga is used as an interactive job submission interface for end-users, and also as a job submission component for higher-level tools. For example GangaRobot is used to perform automated, end-to-end testing of distributed data analysis. Ganga comes with an extensive test suite covering more than 350 test cases. The development model involves all active developers in the release management shifts which is an important and novel approach for the distributed software collaborations. Ganga 5 is a mature, stable and widely-used tool with long-term support from the HEP community.

  12. 'Renewables-Friendly' Grid Development Strategies: Experience in the United States, Potential Lessons for China (Chinese Translation)

    Energy Technology Data Exchange (ETDEWEB)

    Hurlbut, David [National Renewable Energy Lab. (NREL), Golden, CO (United States); Zhou, Ella [National Renewable Energy Lab. (NREL), Golden, CO (United States); Porter, Kevin [Exeter Associates, Columbia, MD (United States); Arent, Douglas J. [Joint Institute for Strategic Energy Analysis, Golden, CO (United States)

    2015-10-03

    This is a Chinese translation of NREL/TP-6A20-64940. This report aims to help China's reform effort by providing a concise summary of experience in the United States with 'renewables-friendly' grid management, focusing on experiences that might be applicable to China. It focuses on utility-scale renewables and sets aside issues related to distributed generation.

  13. A game theoretical approach for cooperative environmentally friendly cellular networks powered by the smart grid

    KAUST Repository

    Ghazzai, Hakim

    2014-11-01

    This paper investigates the collaboration between multiple mobile operators to optimize the energy efficiency of cellular networks, maximize their profits or achieve or tradeoff between both objectives. Mobile operators cooperate together by eliminating redundant base stations (BSs) using a low complexity algorithm that aims to maximize their objective functions subject to a quality of service constraint. The problem is modeled as a two-level Stackelberg game: a mobile operator level and a smart grid level. Indeed, in our framework, we assume that cellular networks are powered by multiple energy providers existing in the smart grid characterized by different pollutant levels in addition to renewable energy source deployed in BS sites. The objective is to find the best active BS combination and the optimal procurement decision needed to the network operation during collaboration by considering electricity real-time pricing. Our study includes the daily traffic variation in addition to the daily green energy availability. Our simulation results show a significant saving in terms of CO2 emissions compared to the non-collaboration case and that cooperative mobile operators exploiting renewables are more awarded than traditional operators. © 2014 IEEE.

  14. Choosing Wood Burning Appliances

    Science.gov (United States)

    Information to assist consumers in choosing a wood burning appliance, including types of appliances, the differences between certified and non-certified appliances, and alternative wood heating options.

  15. Home Appliance Load Scheduling with SEMIAH

    DEFF Research Database (Denmark)

    Jacobsen, Rune Hylsberg; Ghasem Azar, Armin; Zhang, Qi

    2015-01-01

    The European research project SEMIAH aims at designing a scalable infrastructure for residential demand response. This paper presents the progress towards a centralized load scheduling algorithm for controlling home appliances taking power grid constraints and satisfaction of consumers into account....

  16. Minat Masyarakat dalam Menggunakan Smart Appliances

    Directory of Open Access Journals (Sweden)

    Diah Yuniarti

    2014-09-01

    Full Text Available Harga sumber energi yang semakin naik dari tahun ke tahun dan kemajuan teknologi telah mendorong perkembangan smart grid. Smart appliance merupakan salah satu komponen penting dalam smart grid. Penerapan smart appliance sejalan dengan kebijakan untuk mengurangi konsumsi energi, mengurangi emisi karbon dan penyediaan energi dari energi terbarukan. Penetrasi telepon bergerak turut memudahkan manajemen energi dan otomatisasi home appliance. Penelitian ini dilakukan untuk menganalisis minat masyarakat, yang merupakan aktor aktif dalam konsumsi dan manajemen energi di rumah tangga. Data penelitian dianalisis  dengan menggunakan metode structural equation modeling (SEM Hasil penelitian menunjukkan bahwa variabel enjoyment memiliki pengaruh yang signifikan terhadap minat dalam menggunakan smart appliance. Sedangkan, variabel compatibility ease of use, relative advantage dan image tidak memiliki pengaruh yang signifikan terhadap minat menggunakan smart appliance.

  17. Characterization of electrical appliances in transient state

    Science.gov (United States)

    Wójcik, Augustyn; Winiecki, Wiesław

    2017-08-01

    The article contains the study about electrical appliance characterization on the basis of power grid signals. To represent devices, parameters of current and voltage signals recorded during transient states are used. In this paper only transients occurring as a result of switching on devices are considered. The way of data acquisition performed in specialized measurement setup developed for electricity load monitoring is described. The paper presents the method of transients detection and the method of appliance parameters calculation. Using the set of acquired measurement data and appropriate software the set of parameters for several household appliances operating in different operating conditions was processed. Usefulness of appliances characterization in Non-Intrusive Appliance Load Monitoring System (NIALMS) with the use of proposed method is discussed focusing on obtained results.

  18. Appliance based control for Home Power Management Systems

    International Nuclear Information System (INIS)

    Özkan, Hanife Apaydın

    2016-01-01

    This study scrutinizes energy-friendly smart home appliances (hereafter ‘smart appliances’), control of these appliances and their effects on the efficient use of energy. To accomplish this, smart appliances and their operation principles are introduced and their energy savings compared to conventional appliances are analyzed using precise measurements. Then, a real-time Appliance-based Home Power Management System (Ab-HPMS) which manages power consumption of smart appliances and that of the house as a whole is proposed. For Ab-HPMS, an appliance control algorithm, called Appliance-based Rolling Wave Planning (Ab-RWP), is developed with the aim of reducing electricity cost and improving energy efficiency while maintaining user comfort. Ab-RWP algorithm interacts with appliances in a priority order based on user comfort which is determined by utilizing their smart operational characteristics. Operations of smart appliances and their integrations with Ab-HPMS are modeled with Petri nets to verify that they meet the requirements expressed in the specifications. Simulation results demonstrate that proposed Ab-HPMS provides improvements in terms of the energy consumption reduction of about 5%–16%, cost reduction of about 10%–24% and peak reduction at high demand period of about 38%–53% compared to conventional appliances usage. - Highlights: • The effects of smart home appliances on energy saving are investigated. • Petri nets models of smart appliances are developed to simulate their operations in smart home. • A real-time appliance-based home power management system (Ab-HPMS) is proposed. • Power density function is evaluated to interrupt the operation of smart washing machine.

  19. Embedded Systems for Smart Appliances and Energy Management

    CERN Document Server

    Neumann, Peter; Mahlknecht, Stefan

    2013-01-01

    This book provides a comprehensive introduction to embedded systems for smart appliances and energy management, bringing together for the first time a multidisciplinary blend of topics from embedded systems, information technology and power engineering.  Coverage includes challenges for future resource distribution grids, energy management in smart appliances, micro energy generation, demand response management, ultra-low power stand by, smart standby and communication networks in home and building automation.   Provides a comprehensive, multidisciplinary introduction to embedded systems for smart appliances and energy management; Equips researchers and engineers with information required to succeed in designing energy management for smart appliances; Includes coverage of resource distribution grids, energy management in smart appliances, micro energy generation, demand response management, ultra-low power stand by, smart standby and communication networks in home and building automation.  

  20. Ubiquitous Monitoring of Electrical Household Appliances

    Science.gov (United States)

    Lloret, Jaime; Macías, Elsa; Suárez, Alvaro; Lacuesta, Raquel

    2012-01-01

    The number of appliances at home is increasing continuously, mainly because they make our lives easier. Currently, technology is integrated in all objects of our daily life. TCP/IP let us monitor our home in real time and check ubiquitously if something is happening at home. Bearing in mind this idea, we have developed a low-cost system, which can be used in any type of electrical household appliance that takes information from the appliance and posts the information to the Twitter Social network. Several sensors placed in the household appliances gather the sensed data and send them wired or wirelessly, depending on the case, using small and cheap devices to a gateway located in the home. This gateway takes decisions, based on the received data, and sends notifications to Twitter. We have developed a software application that takes the values and decides when to issue an alarm to the registered users (Twitter friends of our smart home). The performance of our system has been measured taking into account the home network (using IEEE 802.3u and IEEE 802.11g) and the data publishing in Twitter. As a result, we have generated an original product and service for any electrical household appliance, regardless of the model and manufacturer, that helps home users improve their quality of life. The paper also shows that there is no system with the same innovative features like the ones presented in this paper. PMID:23202205

  1. Ubiquitous monitoring of electrical household appliances.

    Science.gov (United States)

    Lloret, Jaime; Macías, Elsa; Suárez, Alvaro; Lacuesta, Raquel

    2012-11-07

    The number of appliances at home is increasing continuously, mainly because they make our lives easier. Currently, technology is integrated in all objects of our daily life. TCP/IP let us monitor our home in real time and check ubiquitously if something is happening at home. Bearing in mind this idea, we have developed a low-cost system, which can be used in any type of electrical household appliance that takes information from the appliance and posts the information to the Twitter Social network. Several sensors placed in the household appliances gather the sensed data and send them wired or wirelessly, depending on the case, using small and cheap devices to a gateway located in the home. This gateway takes decisions, based on the received data, and sends notifications to Twitter. We have developed a software application that takes the values and decides when to issue an alarm to the registered users (Twitter friends of our smart home). The performance of our system has been measured taking into account the home network (using IEEE 802.3u and IEEE 802.11g) and the data publishing in Twitter. As a result, we have generated an original product and service for any electrical household appliance, regardless of the model and manufacturer, that helps home users improve their quality of life. The paper also shows that there is no system with the same innovative features like the ones presented in this paper.

  2. Smart grid in China

    DEFF Research Database (Denmark)

    Sommer, Simon; Ma, Zheng; Jørgensen, Bo Nørregaard

    2015-01-01

    China is planning to transform its traditional power grid in favour of a smart grid, since it allows a more economically efficient and a more environmentally friendly transmission and distribution of electricity. Thus, a nationwide smart grid is likely to save tremendous amounts of resources...

  3. Crew appliance study

    Science.gov (United States)

    Proctor, B. W.; Reysa, R. P.; Russell, D. J.

    1975-01-01

    Viable crew appliance concepts were identified by means of a thorough literature search. Studies were made of the food management, personal hygiene, housekeeping, and off-duty habitability functions to determine which concepts best satisfy the Space Shuttle Orbiter and Modular Space Station mission requirements. Models of selected appliance concepts not currently included in the generalized environmental-thermal control and life support systems computer program were developed and validated. Development plans of selected concepts were generated for future reference. A shuttle freezer conceptual design was developed and a test support activity was provided for regenerative environmental control life support subsystems.

  4. Real-time identification of residential appliance events based on power monitoring

    Science.gov (United States)

    Yang, Zhao; Zhu, Zhicheng; Wei, Zhiqiang; Yin, Bo; Wang, Xiuwei

    2018-03-01

    Energy monitoring for specific home appliances has been regarded as the pre-requisite for reducing residential energy consumption. To enhance the accuracy of identifying operation status of household appliances and to keep pace with the development of smart power grid, this paper puts forward the integration of electric current and power data on the basis of existing algorithm. If average power difference of several adjacent cycles varies from the baseline and goes beyond the pre-assigned threshold value, the event will be flagged. Based on MATLAB platform and domestic appliances simulations, the results of tested data and verified algorithm indicate that the power method has accomplished desired results of appliance identification.

  5. File System Virtual Appliances

    Science.gov (United States)

    2010-05-01

    4 KB of data is read or written, data is copied back and forth using trampoline buffers — pages that are shared during proxy initialization — because...in 2008. CIO Magazine. 104 · File system virtual appliances [64] Megiddo, N. and Modha, D. S. 2003. ARC: A Self-Tuning, Low Over- head Replacement

  6. Wisdom Appliance Control System

    Science.gov (United States)

    Hendrick; Jheng, Jyun-Teng; Tsai, Chen-Chai; Liou, Jia-Wei; Wang, Zhi-Hao; Jong, Gwo-Jia

    2017-07-01

    Intelligent appliances wisdom involves security, home care, convenient and energy saving, but the home automation system is still one of the core unit, and also using micro-processing electronics technology to centralized and control the home electrical products and systems, such as: lighting, television, fan, air conditioning, stereo, it composed of front-controller systems and back-controller panels, user using front-controller to control command, and then through the back-controller to powered the device.

  7. Oral radiation protector appliance

    International Nuclear Information System (INIS)

    Persico, T.M.; Dudas, R.M.; Shusta, G.W.

    1982-01-01

    An appliance for protecting teeth, gingiva, periodontal or alveola bone, salivary glands, and adjacent body areas against the harmful side effects of radiation therapy consists of an intraoral portion and an extraoral portion that may be selectively attached. The intraoral portion is substantially u-shaped to encompass the teeth and adjacent areas. The intraoral part may be made of lead sheet coated with plastic; the extraoral portion may be of lead sheet

  8. 46 CFR 111.77-3 - Appliances.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Appliances. 111.77-3 Section 111.77-3 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING ELECTRIC SYSTEMS-GENERAL REQUIREMENTS Appliances and Appliance Circuits § 111.77-3 Appliances. All electrical appliances, including, but...

  9. Modeling of GE Appliances: Cost Benefit Study of Smart Appliances in Wholesale Energy, Frequency Regulation, and Spinning Reserve Markets

    Energy Technology Data Exchange (ETDEWEB)

    Fuller, Jason C.; Parker, Graham B.

    2012-12-31

    This report is the second in a series of three reports describing the potential of GE’s DR-enabled appliances to provide benefits to the utility grid. The first report described the modeling methodology used to represent the GE appliances in the GridLAB-D simulation environment and the estimated potential for peak demand reduction at various deployment levels. The third report will explore the technical capability of aggregated group actions to positively impact grid stability, including frequency and voltage regulation and spinning reserves, and the impacts on distribution feeder voltage regulation, including mitigation of fluctuations caused by high penetration of photovoltaic distributed generation. In this report, a series of analytical methods were presented to estimate the potential cost benefit of smart appliances while utilizing demand response. Previous work estimated the potential technical benefit (i.e., peak reduction) of smart appliances, while this report focuses on the monetary value of that participation. The effects on wholesale energy cost and possible additional revenue available by participating in frequency regulation and spinning reserve markets were explored.

  10. Ubiquitous Monitoring of Electrical Household Appliances 

    Directory of Open Access Journals (Sweden)

    Raquel Lacuesta

    2012-11-01

    Full Text Available The number of appliances at home is increasing continuously, mainly because they make our lives easier. Currently, technology is integrated in all objects of our daily life. TCP/IP let us monitor our home in real time and check ubiquitously if something is happening at home. Bearing in mind this idea, we have developed a low-cost system, which can be used in any type of electrical household appliance that takes information from the appliance and posts the information to the Twitter Social network. Several sensors placed in the household appliances gather the sensed data and send them wired or wirelessly, depending on the case, using small and cheap devices to a gateway located in the home. This gateway takes decisions, based on the received data, and sends notifications to Twitter. We have developed a software application that takes the values and decides when to issue an alarm to the registered users (Twitter friends of our smart home. The performance of our system has been measured taking into account the home network (using IEEE 802.3u and IEEE 802.11g and the data publishing in Twitter. As a result, we have generated an original product and service for any electrical household appliance, regardless of the model and manufacturer, that helps home users improve their quality of life. The paper also shows that there is no system with the same innovative features like the ones presented in this paper.

  11. Documentation of Appliances & Interaction Devices

    DEFF Research Database (Denmark)

    2004-01-01

    The interaction devices and appliances explored in the WorkSPACE project, address spatial computing in the context of work. We have developed and explored a range of appliances and interaction devices. The scope has been to develop tools for support of collaboration by mixing digital and physical...

  12. Remote repair appliance

    International Nuclear Information System (INIS)

    Heumann, F.K.; Wilkinson, J.C.; Wooding, D.R.

    1997-01-01

    A remote appliance for supporting a tool for performing work at a work site on a substantially circular bore of a work piece and for providing video signals of the work site to a remote monitor comprises: a base plate having an inner face and an outer face; a plurality of rollers, wherein each roller is rotatably and adjustably attached to the inner face of the base plate and positioned to roll against the bore of the work piece when the base plate is positioned against the mouth of the bore such that the appliance may be rotated about the bore in a plane substantially parallel to the base plate; a tool holding means for supporting the tool, the tool holding means being adjustably attached to the outer face of the base plate such that the working end of the tool is positioned on the inner face side of the base plate; a camera for providing video signals of the work site to the remote monitor; and a camera holding means for supporting the camera on the inner face side of the base plate, the camera holding means being adjustably attached to the outer face of the base plate. In a preferred embodiment, roller guards are provided to protect the rollers from debris and a bore guard is provided to protect the bore from wear by the rollers and damage from debris. 5 figs

  13. Improvements in appliance holders

    International Nuclear Information System (INIS)

    Chapman, J.E.

    1977-01-01

    Reference is made to appliance holders for locating tools, instruments, etc. in operative relationship to workpieces and accessible through passageways of restricted transverse dimensions. The appliance holder described comprises an elongated external frame provided with transversely, outwardly expanding frictional gripping means in two longitudinally spaced sets and with a ring of spur teeth. An inner elongated frame is held within the external frame in two longitudinally spaced rotary bearings and carries a spur wheel which engages the ring of the spur teeth. A motor is arranged to rotate the spur wheel and hence the inner frame in relation to the external frame. A carriage is carried by the inner frame, longitudinally movable by a motor in relation thereto, and a further carriage is mounted on this first carriage. This second cariage is transversely movable in relation to the inner frame and is provided with a face plate for attachment of tools, instruments, etc. A motor is mounted on the first carriage for moving the second carriage. (U.K.)

  14. Small-Scale Smart Grid Construction and Analysis

    Science.gov (United States)

    Surface, Nicholas James

    The smart grid (SG) is a commonly used catch-phrase in the energy industry yet there is no universally accepted definition. The objectives and most useful concepts have been investigated extensively in economic, environmental and engineering research by applying statistical knowledge and established theories to develop simulations without constructing physical models. In this study, a small-scale version (SSSG) is constructed to physically represent these ideas so they can be evaluated. Results of construction show data acquisition three times more expensive than the grid itself although mainly due to the incapability to downsize 70% of data acquisition costs to small-scale. Experimentation on the fully assembled grid exposes the limitations of low cost modified sine wave power, significant enough to recommend pure sine wave investment in future SSSG iterations. Findings can be projected to full-size SG at a ratio of 1:10, based on the appliance representing average US household peak daily load. However this exposes disproportionalities in the SSSG compared with previous SG investigations and recommended changes for future iterations are established to remedy this issue. Also discussed are other ideas investigated in the literature and their suitability for SSSG incorporation. It is highly recommended to develop a user-friendly bidirectional charger to more accurately represent vehicle-to-grid (V2G) infrastructure. Smart homes, BEV swap stations and pumped hydroelectric storage can also be researched on future iterations of the SSSG.

  15. Transforce lingual appliances pre-adjusted invisible appliances simplify treatment.

    Science.gov (United States)

    Clark, William John

    2011-01-01

    Transforce lingual appliances are designed to be used in conjunction with conventional fixed appliances. Lingual arch development is normally followed by bonded fixed appliances to detail the occlusion. Alternatively Transforce appliance treatment is an efficient method of preparing complex malocclusions prior to a finishing stage with invisible appliances. This approach is ideal for adult treatment, using light continuous forces for arch development with appliances that are comfortable to wear. Sagittal and Transverse appliances are designed for arch development in a range of sizes for contracted arches. They can be used to treat all classes of malocclusion and are pre-adjusted fixed/removable devices for non-compliance treatment. Force modules with nickel titanium coil springs enclosed in a tube deliver a gentle, biocompatible continuous force with a long range of action. They are excellent for mixed dentition and ideal for adult arch development. There are multiple sizes for upper and lower arch development and a sizing chart may be placed over a study model for correct selection, eliminating the need for laboratory work.

  16. Photovoltaic power supply for appliances and small systems. Final report; Photovoltaik fuer Geraete und Kleinsysteme. Schlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Roth, W.; Anton, L.; Benz, J.; Kaiser, R.; Kuhmann, J.; Puls, H.G.; Pfanner, N.; Schmidt, H.; Schulz, W.; Steinhueser, A.

    2002-06-01

    The economic prospects of PV power supply to appliances and small systems were investigated. The research project was aimed at improving the conditions for efficient development of appliances and small systems with photovoltaic power supply and autonomous systems not connected to the grid. Innovative products were developed and tested in cooperation with industrial organizations. The project is to help small and medium-sized organizations with a technological orientation and enhance technology transfer between science and industry.

  17. An orthodontic oral appliance.

    Science.gov (United States)

    Marklund, Marie; Legrell, Per Erik

    2010-11-01

    This pilot study was performed to test the hypothesis that an orthodontic oral appliance (OA) that is designed to work against the backwardly directed forces on the upper incisors may counteract the reduction in overjet from these devices. Thirty patients with normal bites, good oral health, and milder sleep apnea were randomized to treatment with either OAs or orthodontic OAs. Bite changes were evaluated on plaster casts and radiographs and by questionnaires after a mean of 2.4 years in 19 frequent users. Four of nine patients in the orthodontic OA group increased their overjet by > or =0.4 mm, while none of the 10 patients in the OA group experienced that effect. Only the orthodontic OA increases the overjet; this design may therefore be beneficial to patients at risk of negative effects on their bite during OA treatment.

  18. Consumer’s Attitude Towards Investments in Residential Energy-Efficient Appliances: How End-User Choices Contribute to Change Future Energy Systems

    DEFF Research Database (Denmark)

    Baldini, Mattia; Trivella, Alessio; Wente, Jordan William Halverson

    2017-01-01

    conventional and environmentally friendly alternatives when purchasing new household electric appliances. This study employs empirical data from a survey conducted by the Danish Energy Agency to model the decision criteria behind Danish consumer investment in energy-efficient labeled appliances. The analysis...... uses logistic regression over a set of socioeconomic, demographic, and behavioral variables to predict purchase propensities. The findings are relevant for policy makers interested in targeting consumers in the appliance market, particularly for a relatively wealthy national context. The study...

  19. PAT portable appliance testing

    CERN Document Server

    2011-01-01

    The Electricity at Work Regulations 1989 require any electrical system to be constructed, maintained and used in such a manner as to prevent danger. This means that inspection and testing of systems, including portable appliances, is needed in order to determine if maintenance is required.This book explains in clear language what needs to be done and includes expert advice on legislation as well as actual testing. The book contains an appendix providing the electrical fundamentals needed by non-specialists and also has sample questions (with answers) for the C&G 2377 exam that anyone who conducts this work is required to take by law.It is an affordable and handy reference for electricians who administer PAT. It is also an ideal refesher and revision guide for the non-specialist, such as maintenance staff, caretakers and charity shop volunteers who carry out these tasks part-time, alongside their many other duties.Brian Scaddan, I Eng, MIET, is a consultant for and an Honorary Member of City & Guilds. ...

  20. Economics of appliance efficiency

    International Nuclear Information System (INIS)

    Tiedemann, K.H.

    2009-01-01

    Several significant developments occurred in 2001 that affect the impact of market transformation programs. This paper presented and applied an econometric approach to the identification and estimation of market models for refrigerators, clothes washers, dishwashers and room air conditioners. The purpose of the paper was to understand the impact of energy conservation policy developments on sales of energy efficient appliances. The paper discussed the approach with particular reference to building a database of sales and drivers of sales using publicly available information; estimation of the determinants of sales using econometric models; and estimation of the individual impacts of prices, gross domestic product (GDP) and energy conservation policies on sales using regression results. Market and policy developments were also presented, such as change a light, save the world promotion; the California energy crisis; and the Pacific Northwest drought induced hydro power shortage. It was concluded that an increase in GDP increased the sales of both more efficient and less efficient refrigerators, clothes washers, dishwashers, and room air conditioners. An increase in electricity price increased sales of Energy Star refrigerators, clothes washers, dishwashers, and room air conditioners. 4 refs., 8 tabs.

  1. My close friends lurk all around the house, and he knows not!

    Science.gov (United States)

    Singh, Shakuntala A

    2009-01-01

    Technology is a woman's best friend. Gadgets, appliances and contraception make life easy for the present day working woman. Men barely realize the importance of these even if they appear to agree to their use.

  2. Emissions from wood domestic heating appliances

    International Nuclear Information System (INIS)

    Collet, S.

    2009-01-01

    Much research has been carried out to study emissions from wood domestic heating appliances. This work reviews the available emission factors about pollutants produced in different types of wood domestic heating appliances. The main sources of pollutants are older stoves that in most cases are used as an additional heating appliance. These stoves causes higher emissions than modern appliances. Then, substitution of an old type wood appliance with a modern appliance or boiler or a pellet boilers, would reduce considerably emissions in this sector. The efficiency of this measure is estimated for each pollutant. (author)

  3. Compliance with removable orthodontic appliances.

    Science.gov (United States)

    Shah, Nirmal

    2017-12-22

    Data sourcesMedline via OVID, PubMed, Cochrane Central Register of Controlled Trials, Web of Science Core Collection, LILACS and BBO databases. Unpublished clinical trials accessed using ClinicalTrials.gov, National Research Register, ProQuest Dissertation and Thesis database.Study selectionTwo authors searched studies from inception until May 2016 without language restrictions. Quantitative and qualitative studies incorporating objective data on compliance with removable appliances, barriers to appliance wear compliance, and interventions to improve compliance were included.Data extraction and synthesisQuality of research was assessed using the Cochrane Collaboration's risk of bias tool, the risk of bias in non-randomised studies of interventions (ROBINS-I), and the mixed methods appraisal tool. Statistical heterogeneity was investigated by examining a graphic display of the estimated compliance levels in conjunction with 95% confidence intervals and quantified using the I-squared statistic. A weighted estimate of objective compliance levels for different appliances in relation to stipulated wear and self-reported levels was also calculated. Risk of publication bias was assessed using funnel plots. Meta-regression was undertaken to assess the relative effects of appliance type on compliance levels.ResultsTwenty-four studies met the inclusion criteria. Of these, 11 were included in the quantitative synthesis. The mean duration of objectively measured wear was considerably lower than stipulated wear time amongst all appliances. Headgear had the greatest discrepancy (5.81 hours, 95% confidence interval, 4.98, 6.64). Self-reported wear time was consistently higher than objectively measured wear time amongst all appliances. Headgear had the greatest discrepancy (5.02 hours, 95% confidence interval, 3.64, 6.40). Two studies found an increase in compliance with headgear and Hawley retainers when patients were aware of monitoring. Five studies found younger age groups to

  4. Electric emissions from electrical appliances

    International Nuclear Information System (INIS)

    Leitgeb, N.; Cech, R.; Schroettner, J.

    2008-01-01

    Electric emissions from electric appliances are frequently considered negligible, and standards consider electric appliances to comply without testing. By investigating 122 household devices of 63 different categories, it could be shown that emitted electric field levels do not justify general disregard. Electric reference values can be exceeded up to 11-fold. By numerical dosimetry with homogeneous human models, induced intra-corporal electric current densities were determined and factors calculated to elevate reference levels to accounting for reduced induction efficiency of inhomogeneous fields. These factors were found not high enough to allow generally concluding on compliance with basic restrictions without testing. Electric appliances usually simultaneously emit both electric and magnetic fields exposing almost the same body region. Since the sum of induced current densities is limited, one field component reduces the available margin for the other. Therefore, superposition of electric current densities induced by either field would merit consideration. (authors)

  5. Assessment of perceived orthodontic appliance attractiveness.

    Science.gov (United States)

    Ziuchkovski, James P; Fields, Henry W; Johnston, William M; Lindsey, Delwin T

    2008-04-01

    To date, no studies have been published in the literature evaluating the esthetics of orthodontic appliances. The purpose of this study was to assess appliance variables, including appliance type, brand, wire, and ligature tie, for their relative attractiveness. Demographic factors were also evaluated. Appliances were placed in an adult, and digital images were captured, standardized, and incorporated into a computer-based survey. Subjects (n = 200) rated each image for attractiveness on a visual analog scale. The attractiveness ratings were analyzed by using factorial analysis of variance with repeated measures. Post-hoc testing was done with the Tukey-Kramer test (overall a appliances), ceramic, and all self-ligating/stainless steel appliances. No differences between brands in each appliance type were found. Ratings of some ceramic appliances were significantly affected by archwire and ligature tie, depending on several demographic interactions. Orthodontic appliance attractiveness varies by the following hierarchy of appliance types: alternative > ceramic > all stainless steel/self-ligating. Wire and tie selection can affect the appearance of ceramic appliances but have no impact on stainless steel or self-ligating appliances. Certain demographic factors have variable effects on attractiveness ratings.

  6. 24 CFR 3280.714 - Appliances, cooling.

    Science.gov (United States)

    2010-04-01

    ... 24 Housing and Urban Development 5 2010-04-01 2010-04-01 false Appliances, cooling. 3280.714... Systems § 3280.714 Appliances, cooling. (a) Every air conditioning unit or a combination air conditioning... accordance with ANSI Z21.40.1-1996, Gas Fired, Heat Activated, Air Conditioning and Heat Pump Appliances, and...

  7. 24 CFR 3285.503 - Optional appliances.

    Science.gov (United States)

    2010-04-01

    ... 24 Housing and Urban Development 5 2010-04-01 2010-04-01 false Optional appliances. 3285.503... appliances. (a) Comfort cooling systems. When not provided and installed by the home manufacturer, any comfort cooling systems that are installed must be installed according to the appliance manufacturer's...

  8. 49 CFR 238.429 - Safety appliances.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Safety appliances. 238.429 Section 238.429... Equipment § 238.429 Safety appliances. (a) Couplers. (1) The leading and the trailing ends of a semi... appliance mechanical strength and fasteners. (1) All handrails, handholds, and sill steps shall be made of 1...

  9. Urban micro-grids

    International Nuclear Information System (INIS)

    Faure, Maeva; Salmon, Martin; El Fadili, Safae; Payen, Luc; Kerlero, Guillaume; Banner, Arnaud; Ehinger, Andreas; Illouz, Sebastien; Picot, Roland; Jolivet, Veronique; Michon Savarit, Jeanne; Strang, Karl Axel

    2017-02-01

    ENEA Consulting published the results of a study on urban micro-grids conducted in partnership with the Group ADP, the Group Caisse des Depots, ENEDIS, Omexom, Total and the Tuck Foundation. This study offers a vision of the definition of an urban micro-grid, the value brought by a micro-grid in different contexts based on real case studies, and the upcoming challenges that micro-grid stakeholders will face (regulation, business models, technology). The electric production and distribution system, as the backbone of an increasingly urbanized and energy dependent society, is urged to shift towards a more resilient, efficient and environment-friendly infrastructure. Decentralisation of electricity production into densely populated areas is a promising opportunity to achieve this transition. A micro-grid enhances local production through clustering electricity producers and consumers within a delimited electricity network; it has the ability to disconnect from the main grid for a limited period of time, offering an energy security service to its customers during grid outages for example. However: The islanding capability is an inherent feature of the micro-grid concept that leads to a significant premium on electricity cost, especially in a system highly reliant on intermittent electricity production. In this case, a smart grid, with local energy production and no islanding capability, can be customized to meet relevant sustainability and cost savings goals at lower costs For industrials, urban micro-grids can be economically profitable in presence of high share of reliable energy production and thermal energy demand micro-grids face strong regulatory challenges that should be overcome for further development Whether islanding is or is not implemented into the system, end-user demand for a greener, more local, cheaper and more reliable energy, as well as additional services to the grid, are strong drivers for local production and consumption. In some specific cases

  10. Coordinated Scheme of Under-Frequency Load Shedding with Intelligent Appliances in a Cyber Physical Power System

    Directory of Open Access Journals (Sweden)

    Qi Wang

    2016-08-01

    Full Text Available The construction of a cyber physical system in a power grid provides more potential control strategies for the power grid. With the rapid employment of intelligent terminal equipment (e.g., smart meters and intelligent appliances in the environment of a smart grid, abundant dynamic response information could be introduced to support a secure and stable power system. Combining demand response technology with the traditional under-frequency load shedding (UFLS scheme, a new UFLS strategy-determining method involving intelligent appliances is put forward to achieve the coordinated control of quick response resources and the traditional control resources. Based on this method, intelligent appliances can be used to meet the regulatory requirements of system operation in advance and prevent significant frequency drop, thereby improving the flexibility and stability of the system. Time-domain simulation verifies the effectiveness of the scheme, which is able to mitigate frequency drop and reduce the amount of load shedding.

  11. BLOND, a building-level office environment dataset of typical electrical appliances.

    Science.gov (United States)

    Kriechbaumer, Thomas; Jacobsen, Hans-Arno

    2018-03-27

    Energy metering has gained popularity as conventional meters are replaced by electronic smart meters that promise energy savings and higher comfort levels for occupants. Achieving these goals requires a deeper understanding of consumption patterns to reduce the energy footprint: load profile forecasting, power disaggregation, appliance identification, startup event detection, etc. Publicly available datasets are used to test, verify, and benchmark possible solutions to these problems. For this purpose, we present the BLOND dataset: continuous energy measurements of a typical office environment at high sampling rates with common appliances and load profiles. We provide voltage and current readings for aggregated circuits and matching fully-labeled ground truth data (individual appliance measurements). The dataset contains 53 appliances (16 classes) in a 3-phase power grid. BLOND-50 contains 213 days of measurements sampled at 50kSps (aggregate) and 6.4kSps (individual appliances). BLOND-250 consists of the same setup: 50 days, 250kSps (aggregate), 50kSps (individual appliances). These are the longest continuous measurements at such high sampling rates and fully-labeled ground truth we are aware of.

  12. BLOND, a building-level office environment dataset of typical electrical appliances

    Science.gov (United States)

    Kriechbaumer, Thomas; Jacobsen, Hans-Arno

    2018-03-01

    Energy metering has gained popularity as conventional meters are replaced by electronic smart meters that promise energy savings and higher comfort levels for occupants. Achieving these goals requires a deeper understanding of consumption patterns to reduce the energy footprint: load profile forecasting, power disaggregation, appliance identification, startup event detection, etc. Publicly available datasets are used to test, verify, and benchmark possible solutions to these problems. For this purpose, we present the BLOND dataset: continuous energy measurements of a typical office environment at high sampling rates with common appliances and load profiles. We provide voltage and current readings for aggregated circuits and matching fully-labeled ground truth data (individual appliance measurements). The dataset contains 53 appliances (16 classes) in a 3-phase power grid. BLOND-50 contains 213 days of measurements sampled at 50kSps (aggregate) and 6.4kSps (individual appliances). BLOND-250 consists of the same setup: 50 days, 250kSps (aggregate), 50kSps (individual appliances). These are the longest continuous measurements at such high sampling rates and fully-labeled ground truth we are aware of.

  13. Leaking electricity in domestic appliances

    International Nuclear Information System (INIS)

    Meier, Alan; Rosen, Karen

    1999-01-01

    Many types of home electronic equipment draw electric power when switched off or not performing their principal functions. Standby power use (or ''leaking electricity'') for most appliances ranges from 1 - 20 watts. Even though standby use of each device is small, the combined standby power use of all appliances in a home can easily exceed 50 watts. Leaking electricity is already responsible for 5 to 10 percent of residential electricity use in the United States and over 10 percent in Japan. An increasing number of white goods also have standby power requirements. There is a growing international effort to limit standby power to around one watt per device. New and existing technologies are available to meet this target at little or no extra cost

  14. Reduction of peak energy demand based on smart appliances energy consumption adjustment

    Science.gov (United States)

    Powroźnik, P.; Szulim, R.

    2017-08-01

    In the paper the concept of elastic model of energy management for smart grid and micro smart grid is presented. For the proposed model a method for reducing peak demand in micro smart grid has been defined. The idea of peak demand reduction in elastic model of energy management is to introduce a balance between demand and supply of current power for the given Micro Smart Grid in the given moment. The results of the simulations studies were presented. They were carried out on real household data available on UCI Machine Learning Repository. The results may have practical application in the smart grid networks, where there is a need for smart appliances energy consumption adjustment. The article presents a proposal to implement the elastic model of energy management as the cloud computing solution. This approach of peak demand reduction might have application particularly in a large smart grid.

  15. Microbiologically influenced corrosion of orthodontic metallic appliances.

    Science.gov (United States)

    Kameda, Takashi; Oda, Hirotake; Ohkuma, Kazuo; Sano, Natsuki; Batbayar, Nomintsetseg; Terashima, Yukari; Sato, Soh; Terada, Kazuto

    2014-01-01

    Biocorrosion (microbiologically influenced corrosion; MIC) occur in aquatic habitats varying in nutrient content, temperature, stress and pH. The oral environment of organisms, including humans, should be one of the most hospitable for MIC. Corrosion of metallic appliances in the oral region is one cause of metal allergy in patients. In this study, an inductively coupled plasma-optical emission spectrometer revealed elution of Fe, Cr and Ni from stainless steel (SUS) appliances incubated with oral bacteria. Three-dimensional laser confocal microscopy also revealed that oral bacterial culture promoted increased surface roughness and corrosion pits in SUS appliances. The pH of the supernatant was lowered after co-culture of appliances and oral bacteria in any combinations, but not reached at the level of depassivation pH of their metallic materials. This study showed that Streptococcus mutans and Streptococcus sanguinis which easily created biofilm on the surfaces of teeth and appliances, did corrode orthodontic SUS appliances.

  16. 24 CFR 3280.709 - Installation of appliances.

    Science.gov (United States)

    2010-04-01

    ... 24 Housing and Urban Development 5 2010-04-01 2010-04-01 false Installation of appliances. 3280... Fuel Burning Systems § 3280.709 Installation of appliances. (a) The installation of each appliance... the manufacturer's instructions attached to the appliance. Every appliance shall be secured in place...

  17. 24 CFR 3280.707 - Heat producing appliances.

    Science.gov (United States)

    2010-04-01

    ... 24 Housing and Urban Development 5 2010-04-01 2010-04-01 false Heat producing appliances. 3280.707... Systems § 3280.707 Heat producing appliances. (a) Heat-producing appliances and vents, roof jacks and... appliance, the heating appliance shall be installed by the manufacturer of the manufactured home in...

  18. The Determination of Load Profiles and Power Consumptions of Home Appliances

    Directory of Open Access Journals (Sweden)

    Fatih Issi

    2018-03-01

    Full Text Available In recent years, the increment of distributed electricity generation based on renewable energy sources and improvement of communication technologies have caused the development of next-generation power grids known as smart grids. The structures of smart grids have bidirectional communication capability and enable the connection of energy generated from distributed sources to any point on the grid. They also support consumers in energy efficiency by creating opportunities for management of power consumption. The information on power consumption and load profiles of home appliances is essential to perform load management in the dwelling accurately. In this study, the power consumption data for all the basic home appliances, utilized in a two-person family in Çankırı, Turkey, was obtained with high resolution in one-second intervals. The detailed power consumption analysis and load profile were executed for each home appliance. The obtained data is not only the average power consumption of each appliance but also characterizes different operating modes or their cycles. In addition, the impact of these devices on home energy management studies and their standby power consumptions were also discussed. The acquired data is an important source to determine the load profile of individual home appliances precisely in home energy management studies. Although the results of this study do not completely reflect the energy consumption behavior of the people who live in this region, they can reveal the trends in load demands based on a real sample and customer consumption behavior of a typical two-person family.

  19. Designing appliances for mobile commerce and retailtainment

    OpenAIRE

    Roussos, George; Kourouthanassis, P.; Moussouri, T.

    2003-01-01

    In the emerging world of the new consumer and the `anytime, anywhere' mobile commerce, appliances are located at the collision point of the retailer and consumer agendas. The consequence of this is twofold: on the one hand appliances that were previously considered plain and utilitarian become entertainment devices and on the other, for the effective design of consumer appliances it becomes paramount to employ multidisciplinary expertise. In this paper, we discuss consumer perceptions of a re...

  20. Cooking Appliances Using High-Frequency Heating

    OpenAIRE

    木村, 秀行; Hideyuki, KIMURA; (株)日立製作所機械研究所

    2007-01-01

    We have produced a guide suitable for people with no technical knowledge of cooking appliances that use high-frequency heating. In general, cooking appliances that use an electric heat source are popular since, they are simple to use because the offer easy heat control, are safe because they do not have naked flames, and do not make kitchens dirty because there is no exhaust. In recent years, high-efficiency cooking appliances using high-frequency heating technology have surged in popularity....

  1. Fibrotic encapsulation of orthodontic appliance in palate.

    Science.gov (United States)

    Muthu, Jananni; Muthanandam, Sivaramakrishnan; Umapathy, Gubernath; Kannan, Anitha Logaranjani

    2017-01-01

    Iatrogenic trauma though not serious is very common in dental practice. Orthodontic treatment can inflict such injuries as they are prolonged over a long period of time. Ill-fabricated orthodontic appliances, such as wires and brackets, or the patients' habits such as application of constant pressure over the appliance can traumatize the adjacent oral soft tissues. In rare cases, these appliances can get embedded into the mucosa and gingival tissues. This case report describes one such case of iatrogenic trauma to the palatal mucosa due to entrapment of a tongue spike appliance and its surgical management.

  2. Okanagan indoor wood burning appliance inventory survey

    International Nuclear Information System (INIS)

    2001-01-01

    A survey was conducted to determine the usage and nature of wood burning appliances used by residents in British Columbia's Okanagan region. The objective was to better understand this source of air quality concern and to facilitate strategic planning, guidelines and legislation. The survey also provides a baseline to track the effectiveness of any reduction strategies. It identifies the different types of wood burning appliances used in the community and presents residential options about potential bylaws to protect air quality. The receptivity of households to switch to more efficient wood burning appliances was also examined. The survey completes a portion of an overall emissions inventory for the Okanagan Valley. Environment Canada uses the particulate loading results to model the air quality in the airshed. Results showed that approximately 21 per cent of the households in the Okanagan use indoor wood burning appliances, and burn an average of 2.3 cords of wood each year. Only 11 per cent of the appliances are considered to have advanced burning technology. It is projected that the use of wood burning appliances in the Okanagan will increase by 5 to 7 per cent in the next 2 years. Most residents have good burning habits, but some improvements can still be made. Many residents are considering exchanging old wood burning appliances for clean burning technology appliances for environmental and health reasons. Most households would support a bylaw to control nuisance amounts of smoke from wood burning appliances. 20 tabs., 5 figs

  3. Survey of cyber security issues in smart grids

    Science.gov (United States)

    Chen, Thomas M.

    2010-04-01

    The future smart grid will enable cost savings and lower energy use by means of smart appliances and smart meters which support dynamic load management and real-time monitoring of energy use and distribution. The introduction of two-way communications and control into power grid introduces security and privacy concerns. This talk will survey the security and privacy issues in smart grids using the NIST reference model, and relate these issues to cyber security in the Internet.

  4. Smart grid

    International Nuclear Information System (INIS)

    Choi, Dong Bae

    2001-11-01

    This book describes press smart grid from basics to recent trend. It is divided into ten chapters, which deals with smart grid as green revolution in energy with introduction, history, the fields, application and needed technique for smart grid, Trend of smart grid in foreign such as a model business of smart grid in foreign, policy for smart grid in U.S.A, Trend of smart grid in domestic with international standard of smart grid and strategy and rood map, smart power grid as infrastructure of smart business with EMS development, SAS, SCADA, DAS and PQMS, smart grid for smart consumer, smart renewable like Desertec project, convergence IT with network and PLC, application of an electric car, smart electro service for realtime of electrical pricing system, arrangement of smart grid.

  5. Custom Made Pressure Appliance for Presurgical Sustained ...

    African Journals Online (AJOL)

    Among the most common complications of this therapy is ulceration due to excessive pressure. A case of presurgical size reduction for a large ear keloid with a custom made pressure appliance is presented. This novel design of the appliance allows for better control over the amount and direction of the pressure applied on ...

  6. Hydrophilic structures for condensation management in appliances

    Science.gov (United States)

    Kuehl, Steven John; Vonderhaar, John J.; Wu, Guolian; Wu, Mianxue

    2016-02-02

    An appliance that includes a cabinet having an exterior surface; a refrigeration compartment located within the cabinet; and a hydrophilic structure disposed on the exterior surface. The hydrophilic structure is configured to spread condensation. The appliance further includes a wicking structure located in proximity to the hydrophilic structure, and the wicking structure is configured to receive the condensation.

  7. Air conditioning with small power gas appliances

    International Nuclear Information System (INIS)

    Canci, Franco

    1997-01-01

    This article describes research and test activities on small power air conditioning appliances for residential use carried out in the United States, Japan and Europe. The absorption technology aims at the following objectives: to develop appliances requiring reduced maintenance and having a size comparable with electric units of the same output; to reduce production costs and therefore the final prince by adopting special manufacturing technologies such as welded plate exchangers; to obtain appliances which operate both in summer and winter ( as heat pumps), allowing to minimize management and installation costs in southern European climates. The final aim is to offer the customer one appliance only for the following purposes: hot water production for sanitary use, water refrigeration for summer air conditioning, hot water production production for winter heating. This kind of appliance should have management and maintenance costs similar to current individual boilers

  8. Office management of obstructive sleep apnoea: appliances.

    Science.gov (United States)

    Johnson, Matthew D

    2015-08-01

    Oral appliances are becoming increasingly common in the treatment of obstructive sleep apnoea (OSA). They work by advancing the mandible and opening the pharynx. There are several types of devices available for use. Many patients intolerant to continuous positive airway pressure (CPAP) are using oral appliances for OSA. Oral appliances have been shown to improve polysomnography, quality of life and health measures associated with OSA. There is current work to better identify patients who are ideal candidates. Development of titratable devices and monitoring are optimizing usage. They have been compared with CPAP, with both showing improvement in OSA; however, CPAP remains superior overall. Oral appliances are becoming first-line therapy for mild and moderate OSA. They provide a meaningful alternative in severe OSA for patients unable to use CPAP. Device titration and usage monitoring are beginning to hone oral appliances as a therapeutic option.

  9. Energy use and appliance ownership in Ireland

    International Nuclear Information System (INIS)

    Leahy, Eimear; Lyons, Sean

    2010-01-01

    This paper examines household energy use and appliance ownership in Ireland. Logit regression analyses on a large micro-dataset reveal how household characteristics can help explain the ownership of energy using appliances. Using OLS regression models, we explore the factors affecting residential energy demand conditional on appliance ownership. Results suggest that the methods of space and water heating employed by a household are even more important than electrical appliances in explaining domestic energy usage. However, the stock of appliances must be included in such models so that results will not be biased. The methods employed in this paper can be easily adopted for studies of household energy use in other countries where household expenditure survey data are available.

  10. Multi-kanban mechanism for appliance disassembly

    Science.gov (United States)

    Udomsawat, Gun; Gupta, Surendra M.

    2005-11-01

    The use of household appliances continues to rise every year. A significant number of End-Of-Life (EOL) appliances are generated because of the introduction of newer models that are more attractive, efficient and affordable. Others are, of course, generated when they become non-functional. Many regulations encourage recycling of EOL appliances to reduce the amount of waste sent to landfills. In addition, EOL appliances offer the appliance manufacturing and remanufacturing industries a source of less expensive raw materials and components. For this reason product recovery has become a subject of interest during the past decade. In this paper, we study the disassembly line for appliance disassembly. We discuss and incorporate some of the complications that are inherent in disassembly line including product arrival, demand arrival, inventory fluctuation and production control mechanisms. We show how to overcome such complications by implementing a multi-kanban system in the appliance disassembly line setting. The multi-kanban system (MKS) relies on dynamic routing of kanbans according to the state of the system. We investigate the multi-kanban mechanism using simulation and explore the effect of product mix on performance of the traditional push system (TPS) and MKS in terms of controlling the system's inventory while attempting to achieve a decent customer service level.

  11. Retrospective evaluation of appliance price trends

    International Nuclear Information System (INIS)

    Dale, Larry; Antinori, Camille; McNeil, Michael; McMahon, James E.; Sydny Fujita, K.

    2009-01-01

    Real prices of major appliances (refrigerators, dishwashers, heating and cooling equipment) have been falling since the late 1970s despite increases in appliance efficiency and other quality variables. This paper demonstrates that historic increases in efficiency over time, including those resulting from minimum efficiency standards, incur smaller price increases than were expected by the Department of Energy (DOE) forecasts made in conjunction with standards. This effect can be explained by technological innovation, which lowers the cost of efficiency, and by market changes contributing to lower markups and economies of scale in production of higher efficiency units. We reach four principal conclusions about appliance trends and retail price setting: 1.For the past several decades, the retail price of appliances has been steadily falling while efficiency has been increasing. 2.Past retail price predictions made by the DOE analyses of efficiency standards, assuming constant prices over time, have tended to overestimate retail prices. 3.The average incremental price to increase appliance efficiency has declined over time. DOE technical support documents have typically overestimated this incremental price and retail prices. 4.Changes in retail markups and economies of scale in production of more efficient appliances may have contributed to declines in prices of efficient appliances

  12. 46 CFR 188.27-1 - Lifesaving appliances and arrangements.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Lifesaving appliances and arrangements. 188.27-1 Section... VESSELS GENERAL PROVISIONS Lifesaving Appliances and Arrangements § 188.27-1 Lifesaving appliances and arrangements. All lifesaving appliances and arrangements shall be in accordance with the requirements for...

  13. 46 CFR 195.06-1 - Lifesaving appliances and arrangements.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Lifesaving appliances and arrangements. 195.06-1 Section... VESSELS VESSEL CONTROL AND MISCELLANEOUS SYSTEMS AND EQUIPMENT Lifesaving Appliances and Arrangements § 195.06-1 Lifesaving appliances and arrangements. All lifesaving appliances and arrangements shall be...

  14. 46 CFR 90.27-1 - Lifesaving appliances and arrangements.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Lifesaving appliances and arrangements. 90.27-1 Section... VESSELS GENERAL PROVISIONS Lifesaving Appliances and Arrangements § 90.27-1 Lifesaving appliances and arrangements. All lifesaving appliances and arrangements must be in accordance with subchapter W (Lifesaving...

  15. 49 CFR 173.219 - Life-saving appliances.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Life-saving appliances. 173.219 Section 173.219... Life-saving appliances. (a) A life-saving appliance, self-inflating or non-self-inflating, containing small quantities of hazardous materials that are required as part of the life-saving appliance must...

  16. 24 CFR 3280.807 - Fixtures and appliances.

    Science.gov (United States)

    2010-04-01

    ... 24 Housing and Urban Development 5 2010-04-01 2010-04-01 false Fixtures and appliances. 3280.807... Fixtures and appliances. (a) Electrical materials, devices, appliances, fittings, and other equipment... fasten appliances when the manufactured home is in transit. (See § 3280.809.) (b) Specifically listed...

  17. 46 CFR 70.28-1 - Lifesaving appliances and arrangements.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false Lifesaving appliances and arrangements. 70.28-1 Section... PROVISIONS Lifesaving Appliances and Arrangements § 70.28-1 Lifesaving appliances and arrangements. All lifesaving appliances and arrangements on passenger vessels must be in accordance with subchapter W...

  18. Development of a user-friendly, low-cost home energy monitoring and recording system

    International Nuclear Information System (INIS)

    Fletcher, James; Malalasekera, Weeratunge

    2016-01-01

    This paper reports research undertaken to develop a user-friendly home energy monitoring system which is capable of collecting, processing and displaying detailed usage data. The system allows users to monitor power usage and switch their electronic appliances remotely, using any web enabled device, including computers, phones and tablets. The system aims to raise awareness of consumer energy use by gathering data about usage habits, and displaying this information to support consumers when selecting energy tariffs or new appliances. To achieve these aims, bespoke electrical hardware, or ‘nodes’, have been designed and built to monitor power usage, switch devices on and off, and communicate via a Wi-Fi connection, with bespoke software, the ‘server’. The server hosts a webpage which allows users to see a real-time overview of how power is being used in the home as well as allowing scheduled tasks and triggered tasks (which respond to events) to be programmed. The system takes advantage of well standardised networking specifications, such as Wi-Fi and TCP, allowing access from within the home, or remotely through the internet. The server runs under Debian Linux on a Raspberry Pi computer and is written in Python, HTML and JavaScript. The server includes advanced functionality, such as device recognition which allows users to individually monitor several devices that share a single node. The openPicus Flyport is used to provide Wi-Fi connectivity and programmable logic control to nodes. The Flyport is programmed with code compiled from C. - Highlights: • The system is capable of collecting, processing and displaying detailed usage data. • The system is built using commonly available components and software. • Nodes in this system can communicate via a Wi-Fi connection with a server. • The data saved in the server can be used in smart grid applications.

  19. European Gas Appliances Directive and the Dutch Decree on Gas Appliances. Special section

    International Nuclear Information System (INIS)

    De Bruin, B.; Venhorst, T.; Van Tricht, A.

    1998-01-01

    The Gas Appliances Decree is the Dutch translation of the European Gas Appliances Directive. The Decree and the EU Directive contain substantial information, provided they will be read carefully. The EU Directive lays down general safety requirements for gas appliances. They serve as a practical tool for manufacturers and service engineers. In two articles, the Directive is explained, addressing uncertainties and answering important questions. 5 ills

  20. CernVM - a virtual software appliance for LHC applications

    International Nuclear Information System (INIS)

    Buncic, P; Sanchez, C Aguado; Blomer, J; Franco, L; Mato, P; Harutyunian, A; Yao, Y

    2010-01-01

    CernVM is a Virtual Software Appliance capable of running physics applications from the LHC experiments at CERN. It aims to provide a complete and portable environment for developing and running LHC data analysis on any end-user computer (laptop, desktop) as well as on the Grid, independently of Operating System platforms (Linux, Windows, MacOS). The experiment application software and its specific dependencies are built independently from CernVM and delivered to the appliance just in time by means of a CernVM File System (CVMFS) specifically designed for efficient software distribution. The procedures for building, installing and validating software releases remains under the control and responsibility of each user community. We provide a mechanism to publish pre-built and configured experiment software releases to a central distribution point from where it finds its way to the running CernVM instances via the hierarchy of proxy servers or content delivery networks. In this paper, we present current state of CernVM project and compare performance of CVMFS to performance of traditional network file system like AFS and discuss possible scenarios that could further improve its performance and scalability.

  1. A segmented appliance for space closure followed by Invisalign and fixed appliances.

    Science.gov (United States)

    Uribe, Flavio; Cutrera, Alice; Nanda, Ravinda

    2011-01-01

    This case report describes the use of a segmented appliance for space closure prior to using Invisalign. The maxillary right canine was retracted into the extracted first premolar space with a sectional wire from the first molar to the canine with no visible brackets in the incisor region. The advantage of this technique is the ability to achieve better root and rotational control during space closure with a fixed appliance that also has limited visibility. A maxillary fixed appliance was used to refine the esthetics in the maxillary arch due to the limitations of the Invisalign appliance in achieving rotational and vertical movements.

  2. Scheduling home appliances for energy efficient buildings

    DEFF Research Database (Denmark)

    Rossello Busquet, Ana; Kardaras, Georgios; Iversen, Villy Bæk

    2010-01-01

    The number of appliances found in users’ homes is increasing together with electricity consumption of users’ residences. In addition, there is a tendency to consume during the same period leading to demand peaks. During these periods, electricity providers are forced to develop costly methods...... to generate enough power to meet consumers’ requirements. In addition, high demand peaks can lead to electricity shortages or even blackouts in certain areas. In order to avoid demand peaks, users’ appliances should consume electricity in a more distributed way. A new methodology to schedule the usage of home...... appliances is proposed and analyzed. The main concept behind this approach is the aggregation of home appliances into priority classes and the definition of a maximum power consumption threshold, which is not allowed to be exceeded during peak hours. The scenario simulated describes a modern household, where...

  3. 76 FR 79057 - Appliance Labeling Rule

    Science.gov (United States)

    2011-12-21

    ... Part 305 Advertising, Energy conservation, Household appliances, Labeling, Reporting and recordkeeping... emitting diode (OLED) means a thin-film light- emitting device that typically consists of a series of...

  4. The Grid

    CERN Document Server

    Klotz, Wolf-Dieter

    2005-01-01

    Grid technology is widely emerging. Grid computing, most simply stated, is distributed computing taken to the next evolutionary level. The goal is to create the illusion of a simple, robust yet large and powerful self managing virtual computer out of a large collection of connected heterogeneous systems sharing various combinations of resources. This talk will give a short history how, out of lessons learned from the Internet, the vision of Grids was born. Then the extensible anatomy of a Grid architecture will be discussed. The talk will end by presenting a selection of major Grid projects in Europe and US and if time permits a short on-line demonstration.

  5. Quality of Lab Appliances in Orthodontic Offices.

    Science.gov (United States)

    Pruzansky, D P; Park, J H

    Lab appliances are an integral part of orthodontics, from active treatment to retention. The quality and fit of an appliance can affect the treatment result and stability. This study aims to determine common points of failure in orthodontic appliances, and suggest methods to reduce this rate. A survey consisting of 23 questions was distributed to active members of the American Association of Orthodontists (AAO) via Survey Monkey. The most common appliance to need an adjustment was the wrap-around retainer, with the Hawley retainer as a close second. The least common appliance needing adjustment was the Essix/clear retainer. Respondents were asked which component of each appliance was most commonly responsible for an ill-fit. For Hawley and wrap-around retainers, clasps were the most common problem at 50%, whereas spring aligners had two components - clasps and labial bows, both at 38%. Ill-fitting Essix/clear retainers had gingival impingement (52%) closely followed by poor posterior seating (43%). Communication between the orthodontist and lab technician can be improved by establishing a quality assurance protocol for outgoing and incoming cases. The labial bow of Hawley's, wrap-arounds and spring aligners should be clearly demarcated on the casts. Impressions should be free of distortion and casts should be inspected for accuracy. Clear retainers and positioner should be trimmed to avoid gingival impingement. The type of clasp should be selected based on the anatomy of the teeth, and bands should be checked for accuracy of fit.

  6. Using smart meter to monitor the energy consumption of home appliances

    International Nuclear Information System (INIS)

    Dong, M.; Xu, W.

    2010-01-01

    A smart meter provides the foundation for the smart grid, which represent the future electric system in terms of communications, sensors and automation to improve the flexibility, reliability and efficiency of power systems. Smart meters are installed at the utility-customer interface point to provide real-time power usage and price data to each electricity user. The purpose is to create customer awareness on electricity consumption and help users to conserve energy. Smart meters are being deployed throughout North America to replace most traditional meters. However, this paper discussed a major technical gap of the smart meter. Existing smart meters do not provide households with enough feedback needed to achieve effective energy saving. In order to support the energy conservation effort of a customer, the whole house energy data must be displayed on minute or second basis, and it must also be broken down into individual appliance levels. The data of an appliance's energy usage is the most useful information for users to modify their actions and conserve energy. This paper proposed to make the smart meter capable of reporting the overall consumption of a household, as well as monitoring how individual appliances use electricity. It presented a method on using different appliance signatures to identify appliances and make energy estimations on their respective consumptions. Paired with time-of-use or other real time pricing mechanisms, the method enables customers to save energy. This paper also demonstrated how to implement an algorithm on the smart meter platform. Future work will focus on making the algorithm more accurate and faster, and on integrating the smart meter with an appliance energy monitoring system. 21 refs., 6 tabs., 3 figs.

  7. The GridShare solution: a smart grid approach to improve service provision on a renewable energy mini-grid in Bhutan

    International Nuclear Information System (INIS)

    Quetchenbach, T G; Harper, M J; Jacobson, A E; Robinson IV, J; Hervin, K K; Chase, N A; Dorji, C

    2013-01-01

    This letter reports on the design and pilot installation of GridShares, devices intended to alleviate brownouts caused by peak power use on isolated, village-scale mini-grids. A team consisting of the authors and partner organizations designed, built and field-tested GridShares in the village of Rukubji, Bhutan. The GridShare takes an innovative approach to reducing brownouts by using a low cost device that communicates the state of the grid to its users and regulates usage before severe brownouts occur. This demand-side solution encourages users to distribute the use of large appliances more evenly throughout the day, allowing power-limited systems to provide reliable, long-term renewable electricity to these communities. In the summer of 2011, GridShares were installed in every household and business connected to the Rukubji micro-hydro mini-grid, which serves approximately 90 households with a 40 kW nominal capacity micro-hydro system. The installation was accompanied by an extensive education program. Following the installation of the GridShares, the occurrence and average length of severe brownouts, which had been caused primarily by the use of electric cooking appliances during meal preparation, decreased by over 92%. Additionally, the majority of residents surveyed stated that now they are more certain that their rice will cook well and that they would recommend installing GridShares in other villages facing similar problems. (letter)

  8. The advanced smart grid edge power driving sustainability

    CERN Document Server

    Carvallo, Andres

    2011-01-01

    Placing emphasis on practical ""how-to"" guidance, this cutting-edge resource provides you with a first-hand, insider's perspective on the advent and evolution of smart grids in the 21st century (smart grid 1.0). You gain a thorough understanding of the building blocks that comprise basic smart grids, including power plant, transmission substation, distribution, and meter automation. Moreover, this forward-looking volume explores the next step of this technology's evolution. It provides a detailed explanation of how an advanced smart grid incorporates demand response with smart appliances and

  9. Exposure from Appliances (invited paper)

    Energy Technology Data Exchange (ETDEWEB)

    Cartwright, R.A

    1999-07-01

    The dosemeter studies on exposures to ELF electromagnetic irradiation from domestic equipment all suggest the whole-body doses are low, whilst some exposure to extremities could be high but of brief duration. Old style electric overblankets, however, are an exception and produce high fields and relatively high whole-body doses if switched on during the night. Relatively few epidemiological studies have addressed these issues. All of the studies have associated problems of interpretations. Two isolated studies throw up on association with the frequency of spontaneous abortion and electric blanket use whilst another links adult AML and electric shaver usage. Both results could be fortuitous. More consistency appears from three studies of childhood leukaemia. Here statistically significant associations between electric blanket use in pregnancies appear in two separate studies, as does hair dryer use in the case of children: other appliances use associations have been reported. These results are critically assessed. The United Kingdom Childhood Cancer Study (UKCCS) addresses some of these issues as part of a wider ranging assessment of EMF at home and at school. External sources are incorporated with the measurement of domestic ambient conditions in an attempt to make an overall assessment of total exposure. (author)

  10. Cephalometric effects of the Jones Jig appliance followed by fixed appliances in Class II malocclusion treatment.

    Science.gov (United States)

    Patel, Mayara Paim; Henriques, José Fernando Castanha; Freitas, Karina Maria Salvatore; Grec, Roberto Henrique da Costa

    2014-01-01

    The aim of this study was to cephalometrically assess the skeletal and dentoalveolar effects of Class II malocclusion treatment performed with the Jones Jig appliance followed by fixed appliances. The sample comprised 25 patients with Class II malocclusion treated with the Jones Jig appliance followed by fixed appliances, at a mean initial age of 12.90 years old. The mean time of the entire orthodontic treatment was 3.89 years. The distalization phase lasted for 0.85 years, after which the fixed appliance was used for 3.04 years. Cephalograms were used at initial (T1), post-distalization (T2) and final phases of treatment (T3). For intragroup comparison of the three phases evaluated, dependent ANOVA and Tukey tests were used. Jones Jig appliance did not interfere in the maxillary and mandibular component and did not change maxillomandibular relationship. Jones Jig appliance promoted distalization of first molars with anchorage loss, mesialization and significant extrusion of first and second premolars, as well as a significant increase in anterior face height at the end of treatment. The majority of adverse effects that occur during intraoral distalization are subsequently corrected during corrective mechanics. Buccal inclination and protrusion of mandibular incisors were identified. By the end of treatment, correction of overjet and overbite was observed. Jones Jig appliance promoted distalization of first molars with anchorage loss represented by significant mesial movement and extrusion of first and second premolars, in addition to a significant increase in anterior face height.

  11. Orthodontic appliance preferences of children and adolescents.

    Science.gov (United States)

    Walton, Daniel K; Fields, Henry W; Johnston, William M; Rosenstiel, Stephen F; Firestone, Allen R; Christensen, James C

    2010-12-01

    Although attractiveness and acceptability of orthodontic appliances have been rated by adults for themselves and for adolescents, children and adolescents have not provided any substantial data. The objective of this study was to evaluate preferences and acceptability of orthodontic appliances in children and adolescents. Images of orthodontic appliances previously captured and standardized were selected and incorporated into a computer-based survey. Additional images of shaped brackets and colored elastomeric ties, as well as discolored clear elastomeric ties, were captured and incorporated onto existing survey images with Photoshop (Adobe, San Jose, Calif). The survey displayed 12 orthodontic appliance variations to 139 children in 3 age groups: 9 to 11 years (n = 45), 12 to 14 years (n = 49), and 15 to 17 years (n = 45). The subjects rated each image for attractiveness and acceptability. All images were displayed and rated twice to assess rater reliability. Overall reliability ratings were r = 0.74 for attractiveness and k = 0.66 for acceptability. There were significant differences in bracket attractiveness and acceptability in each age group. The highest-rated appliances were clear aligners, twin brackets with colored ties, and shaped brackets with and without colored ties. Colored elastomeric ties improved attractiveness significantly over brackets without colored ties for children in the 12-to-14 year group. There was a tendency for older subjects to rate clear orthodontic appliances higher than did younger subjects. Ceramic brackets with discolored ties tended to be rated lower than ceramic brackets with new ties and scored lowest in acceptability and attractiveness in all age groups. Girls rated shaped brackets significantly higher than did boys. Children's preferences for orthodontic appliances differ by age and sex. Child and adolescent preferences differ from adult preferences. Copyright © 2010 American Association of Orthodontists. Published by Mosby

  12. The ENCOURAGE ICT architecture for heterogeneous smart grids

    DEFF Research Database (Denmark)

    Albano, Michele; Ferreira, Luis; Le Guilly, Thibaut

    2013-01-01

    The ENCOURAGE project aims at rationalizing energy usage in building by implementing a smart energy grid based on intelligent scheduling of energy consuming appliances, renewable energy production, and inter-building energy trading. This paper presents the reference architecture proposed in the c...

  13. On the value of device flexibility in smart grid applications

    NARCIS (Netherlands)

    Gerards, M. E. T.; Hurink, J. L.

    2017-01-01

    Demand-side management and demand response are proposed as a means to solve different objectives in smart grids, such as, e.g., maximizing self-consumption of a house or peak shaving. Crucial components in these approaches are load shiftable/steerable devices, so-called smart appliances. Although

  14. PowerMatching City : A unique smart grid project

    NARCIS (Netherlands)

    dr. C.J. Wiekens

    2014-01-01

    In this presentation, the smart grid project 'PowerMatching City' is introduced. PowerMatching City is a living lab demonstration of the future energy system. In PowerMatching City the connected households are equipped with a mix of decentralized energy sources, hybrid heat pumps, smart appliances,

  15. Pellet fired appliances. Market survey. 7. rev. ed.; Pelletheizungen. Marktuebersicht

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2013-01-15

    The market survey under consideration reports on pellet central heating systems and pellet fired appliances. The main chapters of this market survey are concerned to: (1) Information on wood pellets and pellet fired appliances; (2) Information about the interpretation of the market survey; (3) Survey of all compared pellet fired appliances with respect to the nominal power; (4) Price lists of pellet fired appliances and pellet central heating systems; (5) Type sheets of the compared pellet fired appliances and pellet central heating systems. Finally, this brochure contains the addresses of the produces and distribution partners of pellet fired appliances and pellet central heating systems.

  16. Advances in household appliances- A review

    International Nuclear Information System (INIS)

    Bansal, Pradeep; Vineyard, Edward; Abdelaziz, Omar

    2011-01-01

    An overview of options and potential barriers and risks for reducing the energy consumption, peak demand, and emissions for seven key energy consuming residential products (refrigerator-freezers, dishwashers, clothes washers, clothes dryers, electric ovens, gas ovens and microwave ovens) is presented. The paper primarily concentrates on the potential energy savings from the use of advanced technologies in appliances for the U.S. market. The significance and usefulness of each technology was evaluated in order to prioritize the R and D needs to improve energy efficiency of appliances in view of energy savings, cost, and complexity. The paper provides a snapshot of the future R and D needs for each of the technologies along with the associated barriers. Although significant energy savings may be achieved, one of the major barriers in most cases is high first cost. One way of addressing this issue and promoting the introduction of new technologies is to 'level' the playing field for all manufacturers by establishing Minimum Energy Performance Standards (MEPS) which are not cost prohibitive and promoting energy efficient products through incentives to both manufacturers and consumers. - Highlights: → This paper presents latest developments/status of advanced residential appliances. → Stringent minimum energy performance standards can reduce appliance energy use. → There is a potential to reduce energy use in appliances by up to 50%.

  17. Colostomies and the use of colostomy appliances.

    Science.gov (United States)

    Cronin, Elaine

    The surgical formation of a colostomy is indicated as part of the treatment of various conditions, primarily colon cancer, requiring the patient (ostomist) to wear a colostomy pouch. Today's stoma appliances bear no resemblance to those worn three or four decades ago when colostomy, ileostomy and urostomy bags were made entirely from rubber. The patient, who would have two to three bags in circulation at a time, would interchange them allowing for the washing and drying of the previous one, thus minimizing odour and potential perishing of the rubber. The design of these appliances was simple, but they were large and bulky and the outlet resembled that of a hot-water bottle stopper or a cap from an old soda bottle that required the insertion of coinage (2p) to open it. This article explores the range of colostomy appliances and management options available to the nurse when caring for patients with a colostomy.

  18. Extra-oral Appliances in Orthodontic Treatment.

    Science.gov (United States)

    Almuzian, Mohammed; Alharbi, Fahad; McIntyre, Grant

    2016-01-01

    Extra-oral appliances are used in orthodontics to apply forces to the jaws, dentition or both and the popularity of these appliances is cyclical. Although the use of retraction headgear for the management of Class II malocclusion has declined over the last 20 years with the refinement of non-compliance approaches, including temporary anchorage devices, headgear still has a useful role in orthodontics. The use of protraction headgear has increased as more evidence of its effectiveness for the treatment of Class lIl malocclusion has become available. This paper describes the mechanics and contemporary uses of headgear in orthodontics for primary care dentists and specialist orthodontists. CPD/CLINICAL RELEVANCE: Extra-oral appliances have specific uses in orthodontic biomechanics. Clinicians using retraction headgear and protraction headgear should be familiar with their clinical indications, the potential problems and how these can be avoided.

  19. The greenhouse advantage of natural gas appliances

    International Nuclear Information System (INIS)

    Coombe, N.

    2000-01-01

    The life cycle report prepared recently by Energetics for the AGA, Assessment of Greenhouse Gas Emissions from Natural Gas, demonstrates clearly the greenhouse advantage natural gas has over coal in generating electricity. This study also goes one step further in applying this life cycle approach to the use of space and water heating within the home. The study shows the significant green-house advantage that natural gas appliances have over electric appliances. Findings from other studies also support this claim. The natural gas suppliers are encouraged to take advantage of the marketing opportunity that these studies provide, offering the householders the fuel that will significantly reduce their contribution to greenhouse emission

  20. Gas appliances in the domestic market - legal basis and questioning concerning the Directive for Gas Appliances

    International Nuclear Information System (INIS)

    Rienen, W. van

    1994-01-01

    Four years after the Directive for Gas Appliances has been passed by the European Community it shows the first effects on the market. Gas appliances bearing an CE label can prove that the EC-standardised demands are observed. Thus it can be demanded from every member state by law not to hinder a launch on the market and the initiation. The directive also effects the demands for national environmental protection. A new DVGW (Deutscher Verein des Gas und Wasserfaches e.V.) quality label for gas appliances is going to certify the observance of a quality level which exceeds the minimum EC level. (orig.) [de

  1. Equipment and appliances for underwater operations. Pt. 2

    International Nuclear Information System (INIS)

    Krueger, P.

    1976-01-01

    The 6/75 edition of 'mt' reported on the 'ARGE underwater appliances' and the study on 'design development of appliances and equipment for underwater use' in a brief summary. One of these designs, the 'unmanned DSWS underwater appliance' was described in detail. The present article describes three further design developments mentioned in the above study and which are based on unmanned appliances connected to the mother-ship. These designs were developed by Preussag-Meerestechnik. (orig.) [de

  2. Grid Security

    CERN Multimedia

    CERN. Geneva

    2004-01-01

    The aim of Grid computing is to enable the easy and open sharing of resources between large and highly distributed communities of scientists and institutes across many independent administrative domains. Convincing site security officers and computer centre managers to allow this to happen in view of today's ever-increasing Internet security problems is a major challenge. Convincing users and application developers to take security seriously is equally difficult. This paper will describe the main Grid security issues, both in terms of technology and policy, that have been tackled over recent years in LCG and related Grid projects. Achievements to date will be described and opportunities for future improvements will be addressed.

  3. Establishing Design Strategies and an Assessment Tool of Home Appliances to Promote Sustainable Behavior for the New Poor

    Directory of Open Access Journals (Sweden)

    Jui-Che Tu

    2018-05-01

    Full Text Available Environmental benefits related to home appliance life cycles depend on how these products are used. Designing home appliances that promote sustainable behavior is an effective way to reduce environmental impacts. This study aimed to increase relevant opportunities for promoting sustainable behavior practices on the new poor through home appliances, which is rarely discussed in the fields of design for sustainable behavior (DfSB and product design. In particular, relevant assessment tools or indicators are lacking in DfSB, and people’s use of home appliances is generally unsustainable. Therefore, repertory grid technology was used to understand the perceptions of the new poor, develop an assessment tool, and construct design strategies for home appliances that promote sustainable behavior. Data were collected from the new poor and from designers. Through cluster and principal component analyses, three strategy types were proposed that corresponded to different product features, suggestions, and guidance. In addition, the effectiveness and potential of an assessment tool were demonstrated using the Wilcoxon rank test. The findings could be used by designers, retailers, and green marketers to propose effective product design programs that promote sustainable behavior of the new poor during product use.

  4. 14 CFR 25.1365 - Electrical appliances, motors, and transformers.

    Science.gov (United States)

    2010-01-01

    ... Equipment § 25.1365 Electrical appliances, motors, and transformers. (a) Domestic appliances must be... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Electrical appliances, motors, and transformers. 25.1365 Section 25.1365 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF...

  5. 46 CFR 78.17-5 - Valves and closing appliances.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false Valves and closing appliances. 78.17-5 Section 78.17-5..., Drills, and Inspections § 78.17-5 Valves and closing appliances. (a) It shall be the duty of the master to see that all valves, including cross connecting valves where fitted, and other appliances such as...

  6. 46 CFR 109.209 - Appliances for watertight integrity.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Appliances for watertight integrity. 109.209 Section 109... OPERATIONS Tests, Drills, and Inspections § 109.209 Appliances for watertight integrity. (a) Before getting underway, the master or person in charge shall insure that each appliance for watertight integrity is...

  7. 46 CFR 78.47-38 - Valves and closing appliances.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false Valves and closing appliances. 78.47-38 Section 78.47-38... Fire and Emergency Equipment, Etc. § 78.47-38 Valves and closing appliances. (a) All valves and closing appliances, or other mechanisms which may be required to be operated for damage control purposes in case of...

  8. Load Characterization for small domestic appliances and electronics

    NARCIS (Netherlands)

    Van der Sluis, P.

    2009-01-01

    In this report, the energy consumption of small domestic loads has been analysed. To make the around 100 types of appliances considereda bit manageable, the appliances were categorized into several groups. The possibilities for time-shifting of the energy use of these small appliances was

  9. 38 CFR 17.150 - Prosthetic and similar appliances.

    Science.gov (United States)

    2010-07-01

    ... appliances. 17.150 Section 17.150 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS AFFAIRS MEDICAL Prosthetic, Sensory, and Rehabilitative Aids § 17.150 Prosthetic and similar appliances... appliances including invalid lifts and therapeutic and rehabilitative devices, and special clothing made...

  10. 46 CFR 199.70 - Personal lifesaving appliances.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Personal lifesaving appliances. 199.70 Section 199.70 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) LIFESAVING APPLIANCES AND ARRANGEMENTS... appliances. (a) Lifebuoys. Each vessel must carry lifebuoys approved under approval series 160.150 as follows...

  11. 42 CFR 409.14 - Supplies, appliances, and equipment.

    Science.gov (United States)

    2010-10-01

    ... 42 Public Health 2 2010-10-01 2010-10-01 false Supplies, appliances, and equipment. 409.14 Section... Hospital Services § 409.14 Supplies, appliances, and equipment. (a) Except as specified in paragraph (b) of this section, Medicare pays for supplies, appliances, and equipment as inpatient hospital or inpatient...

  12. Grid Computing

    Indian Academy of Sciences (India)

    A computing grid interconnects resources such as high performancecomputers, scientific databases, and computercontrolledscientific instruments of cooperating organizationseach of which is autonomous. It precedes and is quitedifferent from cloud computing, which provides computingresources by vendors to customers ...

  13. Grid Computing

    Indian Academy of Sciences (India)

    IAS Admin

    emergence of supercomputers led to the use of computer simula- tion as an .... Scientific and engineering applications (e.g., Tera grid secure gate way). Collaborative ... Encryption, privacy, protection from malicious software. Physical Layer.

  14. Mandibular advancement appliance for obstructive sleep apnoea

    DEFF Research Database (Denmark)

    Petri, Niels; Svanholt, Palle; Solow, Beni

    2008-01-01

    The aim of this trial was to evaluate the efficacy of a mandibular advancement appliance (MAA) for obstructive sleep apnoea (OSA). Ninety-three patients with OSA and a mean apnoea-hypopnoea index (AHI) of 34.7 were centrally randomised into three, parallel groups: (a) MAA; (b) mandibular non...

  15. A modified, lingually supported cantilevered Herbst appliance.

    Science.gov (United States)

    Snodgrass, D

    1996-01-01

    This new, fixed-functional appliance/Herbst/Bioprogressive system is designed for patient comfort and mandatory compliance. It also combines the positive clinical effects of four fixed-functional systems. It allows rapid palatal expansion of the upper arch, alveolar uprighting of the lower arch, upper and lower incisor alignment, and sagittal correction of Class II malocclusions to occur simultaneously with one appliance fixed in both arches. It is indicated for use in growing patients with skeletal Class II malocclusions. The ideal timing for treatment is the late mixed dentition. Being able to remove the appliance after one year with the upper second bicuspids erupting slightly Class III so the clinician can immediately begin fixed finishing mechanics would be ideal. This new Herbst design will reduce the frequency of orthognathic surgery and upper bicuspid extraction to camouflage Class II malocclusions. At the same time, it gives total control to the clinician in treating some more difficult, non-compliant patients. Fixed-functional appliances, which improve treatment efficiency and treatment results and provide for patient comfort, while at the same time give the treating clinician almost total control of the three planes of facial growth will open new doors for orthodontic treatment and research in the next century.

  16. Incorporating experience curves in appliance standards analysis

    International Nuclear Information System (INIS)

    Desroches, Louis-Benoit; Garbesi, Karina; Kantner, Colleen; Van Buskirk, Robert; Yang, Hung-Chia

    2013-01-01

    There exists considerable evidence that manufacturing costs and consumer prices of residential appliances have decreased in real terms over the last several decades. This phenomenon is generally attributable to manufacturing efficiency gained with cumulative experience producing a certain good, and is modeled by an empirical experience curve. The technical analyses conducted in support of U.S. energy conservation standards for residential appliances and commercial equipment have, until recently, assumed that manufacturing costs and retail prices remain constant during the projected 30-year analysis period. This assumption does not reflect real market price dynamics. Using price data from the Bureau of Labor Statistics, we present U.S. experience curves for room air conditioners, clothes dryers, central air conditioners, furnaces, and refrigerators and freezers. These experience curves were incorporated into recent energy conservation standards analyses for these products. Including experience curves increases the national consumer net present value of potential standard levels. In some cases a potential standard level exhibits a net benefit when considering experience, whereas without experience it exhibits a net cost. These results highlight the importance of modeling more representative market prices. - Highlights: ► Past appliance standards analyses have assumed constant equipment prices. ► There is considerable evidence of consistent real price declines. ► We incorporate experience curves for several large appliances into the analysis. ► The revised analyses demonstrate larger net present values of potential standards. ► The results imply that past standards analyses may have undervalued benefits.

  17. Custom Made Pressure Appliance for Presurgical Sustained ...

    African Journals Online (AJOL)

    was done to match the color of the appliance with that of the adjoining skin to make ... of the surface of the swelling with the gap between the two ... Figure 1: Preoperative view of keloid .... “multi model” approach for treating ear keloids. Indian J ...

  18. Educational Electrical Appliance Power Meter and Logger

    Science.gov (United States)

    Nunn, John

    2013-01-01

    The principles behind two different designs of inductive power meter are presented. They both make use of the microphone input of a computer which, together with a custom-written program, can record the instantaneous power of a domestic electrical appliance. The device can be built quickly and can be calibrated with reference to a known power…

  19. Smart Grid Security A Smart Meter-Centric Perspective

    DEFF Research Database (Denmark)

    Vigo, Roberto; Yuksel, Ender; Ramli, Carroline Dewi Puspa Kencana

    2012-01-01

    , leading to what is known as the Smart Grid. The development of this Cyber-Physical System introduces new security issues, thus calling for efforts in studying possible attacks and devising suitable countermeasures. In this paper, we review a generic model for the Smart Grid, and present possible attacks......The electricity grid is a key infrastructure for our society, therefore its security is a critical public concern. This physical system is becoming more and more complex as it is coupled with a cyber layer carrying information about power usage and control instructions for intelligent appliances...

  20. Mobile based Appliances switching using Bluetooth

    Science.gov (United States)

    Gupta, Sureshchandra J., Dr; Desai, Kalp; Gaikawad, Deepak; Pawar, Vijay N.; Gangal, Devendranath R.

    2008-04-01

    How many times do you have to get up from your desk to switch on your Air conditioner or fan when you are completely into your table work? How many times do you feel lazy to get off your comfort to switch on/off your home appliances in different rooms? How much energy do you lose in a day for operating your appliances? The solution is either a large amount of manual work—or the idea that is presented over here: APP-CON (APP-CON stands for appliances control). Here the ordinary cell phone with bluetooth capability acts as remote designed in such a manner that it acts as a helping hand to human by reducing its manual work and therefore saving human energy. The cell phone control of APP-CON units lets you access many of your home appliances situated in different rooms by using just a single remote from distance. Electronics hobbyists would love to make such a remote control themselves. But they find it difficult due to complex circuitry rather than the high cost because of using a number of frequency counting techniques and decade counters. The APP-CON system given here overcomes the aforesaid problems by using a single microcontroller and moreover a simple program or software for bluetooth enabled cell phone and employing simple coding and decoding of remote signals. Here the mobile based remote control is used to operate a number of home appliances basically consists of Bluetooth technology. The unit consists of a transmitter and a receiver consisting of a microcontroller. The importance of bluetooth technology is that the signal to be transmitted from transmitter to the receiver is done without requiring line of sight.

  1. GridWise Standards Mapping Overview

    Energy Technology Data Exchange (ETDEWEB)

    Bosquet, Mia L.

    2004-04-01

    ''GridWise'' is a concept of how advanced communications, information and controls technology can transform the nation's energy system--across the spectrum of large scale, central generation to common consumer appliances and equipment--into a collaborative network, rich in the exchange of decision making information and an abundance of market-based opportunities (Widergren and Bosquet 2003) accompanying the electric transmission and distribution system fully into the information and telecommunication age. This report summarizes a broad review of standards efforts which are related to GridWise--those which could ultimately contribute significantly to advancements toward the GridWise vision, or those which represent today's current technological basis upon which this vision must build.

  2. Removable orthodontic appliances: new perspectives on capabilities and efficiency.

    Science.gov (United States)

    Hamid Zafarmand, A; Mahdi Zafarmand, M

    2013-06-01

    Removable appliances are a dependable choice for many patients but like all orthodontic appliances, they have some limitations in use. Patient selection and appropriate appliance design are two key factors for success. Many patients, especially adults, prefer intra-oral appliances to extra-oral devices. Sometimes a removable intra-oral appliance can solve a dental problem in a shorter period of time compared to fixed treatment, and this has also been repeatedly seen in molar distalisation. From the interceptive perspective, the appliance can prevent or alleviate an impending crowding for erupting permanent incisors. This article describes 5 patients with different orthodontic problems: impending crowding for erupting upper canine with 2 approaches, provision of space for upper cuspids, resolution of chronic attrition of anterior teeth, relief of space shortage for upper canines eruption, and reduction of excess overjet. All subjects were treated with removable appliances of various designs.

  3. A Cloud Associated Smart Grid Admin Dashboard

    Directory of Open Access Journals (Sweden)

    P. Naveen

    2018-02-01

    Full Text Available Intelligent smart grid system undertakes electricity demand in a sustainable, reliable, economical and environmentally friendly manner. As smart grid involves, it has the liability of meeting the changing consumer needs on the day-to-day basis. Modern energy consumers like to vivaciously regulate their consumption patterns more competently and intelligently than current provided ways. To fulfill the consumers’ needs, smart meters and sensors make the grid infrastructure more efficient and resilient in energy data collection and management even with the ever-changing renewable power generation. Though cloud acts as an outlet for the energy consumers to retrieve energy data from the grid, the information systems available are technically constrained and not user-friendly. Hence, a simple technology enabled utility-consumer interactive information system in the form of a dashboard is presented to cater the electric consumer needs.

  4. Grid-connected photovoltaic system design for local government ...

    African Journals Online (AJOL)

    Grid-connected photovoltaic system design for local government offices in Nigeria. ... Nigerian Journal of Technology. Journal Home ... It is neat, silent and elegant process of generating electric power in environmentally friendly manner. In this ...

  5. TiArA: a virtual appliance for the analysis of Tiling Array data.

    Directory of Open Access Journals (Sweden)

    Jason A Greenbaum

    2010-04-01

    Full Text Available Genomic tiling arrays have been described in the scientific literature since 2003, yet there is a shortage of user-friendly applications available for their analysis.Tiling Array Analyzer (TiArA is a software program that provides a user-friendly graphical interface for the background subtraction, normalization, and summarization of data acquired through the Affymetrix tiling array platform. The background signal is empirically measured using a group of nonspecific probes with varying levels of GC content and normalization is performed to enforce a common dynamic range.TiArA is implemented as a standalone program for Linux systems and is available as a cross-platform virtual machine that will run under most modern operating systems using virtualization software such as Sun VirtualBox or VMware. The software is available as a Debian package or a virtual appliance at http://purl.org/NET/tiara.

  6. Friend Finder (Game)

    Science.gov (United States)

    ... for a spot on the Friend Finder All-Star List. Earn your spot by showing you're savvy when it comes to making friends online . Downloads Please download and share our ... Email Updates Blog Feed Facebook YouTube Twitter The Federal Trade Commission (FTC) is the ...

  7. OS Friendly Microprocessor Architecture

    Science.gov (United States)

    2017-04-01

    NOTES Patrick La Fratta is now affiliated with Micron Technology, Inc., Boise, Idaho. 14. ABSTRACT We present an introduction to the patented ...Operating System Friendly Microprocessor Architecture (OSFA). The software framework to support the hardware-level security features is currently patent ...Army is assignee. OS Friendly Microprocessor Architecture. United States Patent 9122610. 2015 Sep. 2. Jungwirth P, inventor; US Army is assignee

  8. Oral appliances and functional orthopaedic appliances for obstructive sleep apnoea in children.

    Science.gov (United States)

    Carvalho, F R; Lentini-Oliveira, D; Machado, M A C; Prado, G F; Prado, L B F; Saconato, H

    2007-04-18

    Apnoea is a breathing disorder marked by the absence of airflow at the nose or mouth. In children, risk factors include adenotonsillar hypertrophy, obesity, neuromuscular disorders and craniofacial anomalies. The most common treatment for obstructive sleep apnoea syndrome (OSAS) in childhood is adenotonsillectomy. This approach is limited by its surgical risks, mostly in children with comorbities and, in some patients, by recurrence that can be associated with craniofacial problems. Oral appliances and functional orthopaedic appliances have been used for patients who have OSAS and craniofacial anomalies because they change the mandible posture forwards and potentially enlarge the upper airway and increase the upper airspace, improving the respiratory function. To assess the effectiveness of oral appliances or functional orthopaedic appliances for OSAS in children. A sensitive search was developed for the Cochrane Central Register of Controlled Trials (CENTRAL) (The Cochrane Library 2005, Issue 3); PubMed (January 1966 to September 2005); EMBASE (1980 to September 2005); Lilacs (1982 to September 2005); BBO-Bibliografia Brasileira de Odontologia (1986 to September 2005); and SciELO (1997 to September 2005). There was no restriction of language or source of information. All randomised or quasi-randomised controlled trials comparing all types of oral and functional orthopaedic appliances with placebo or no treatment, in children 15 years old or younger. reduction of apnoea to less than one episode per hour. dental and skeletal relationship, sleep parameters improvement, cognitive and phonoaudiologic function, behavioural problems, drop outs and withdrawals, quality of life, side effects (tolerability), economic evaluation. Data were independently extracted by two review authors. Authors were contacted for additional information. Risk ratios with 95% confidence intervals were calculated for all important dichotomous outcomes. The initial search identified 384 trials

  9. Catalytic combustion in small wood burning appliances

    Energy Technology Data Exchange (ETDEWEB)

    Oravainen, H. [VTT Energy, Jyvaeskylae (Finland)

    1996-12-31

    There is over a million hand fired small heating appliances in Finland where about 5,4 million cubic meters of wood fuel is used. Combustion in such heating appliances is a batch-type process. In early stages of combustion when volatiles are burned, the formation of carbon monoxide (CO) and other combustible gases are difficult to avoid when using fuels that have high volatile matter content. Harmful emissions are formed mostly after each fuel adding but also during char burnout period. When the CO-content in flue gases is, say over 0.5 %, also other harmful emissions will be formed. Methane (CH{sub 4}) and other hydrocarbons are released and the amount of polycyclic aromatic hydrocarbons (PAH)-compounds can be remarkable. Some PAH-compounds are very carcinogenic. It has been estimated that in Finland even more than 90 % of hydrocarbon and PAH emissions are due to small scale wood combustion. Emissions from transportation is excluded from these figures. That is why wood combustion has a net effect on greenhouse gas phenomena. For example carbon monoxide emissions from small scale wood combustion are two fold compared to that of energy production in power plants. Methane emission is of the same order as emission from transportation and seven fold compared with those of energy production. Emissions from small heating appliances can be reduced by developing the combustion techniques, but also by using other means, for example catalytic converters. In certain stages of the batch combustion, temperature is not high enough, gas mixing is not good enough and residence time is too short for complete combustion. When placed to a suitable place inside a heating appliance, a catalytic converter can oxidize unburned gases in the flue gas into compounds that are not harmful to the environment. (3 refs.)

  10. Catalytic combustion in small wood burning appliances

    Energy Technology Data Exchange (ETDEWEB)

    Oravainen, H [VTT Energy, Jyvaeskylae (Finland)

    1997-12-31

    There is over a million hand fired small heating appliances in Finland where about 5,4 million cubic meters of wood fuel is used. Combustion in such heating appliances is a batch-type process. In early stages of combustion when volatiles are burned, the formation of carbon monoxide (CO) and other combustible gases are difficult to avoid when using fuels that have high volatile matter content. Harmful emissions are formed mostly after each fuel adding but also during char burnout period. When the CO-content in flue gases is, say over 0.5 %, also other harmful emissions will be formed. Methane (CH{sub 4}) and other hydrocarbons are released and the amount of polycyclic aromatic hydrocarbons (PAH)-compounds can be remarkable. Some PAH-compounds are very carcinogenic. It has been estimated that in Finland even more than 90 % of hydrocarbon and PAH emissions are due to small scale wood combustion. Emissions from transportation is excluded from these figures. That is why wood combustion has a net effect on greenhouse gas phenomena. For example carbon monoxide emissions from small scale wood combustion are two fold compared to that of energy production in power plants. Methane emission is of the same order as emission from transportation and seven fold compared with those of energy production. Emissions from small heating appliances can be reduced by developing the combustion techniques, but also by using other means, for example catalytic converters. In certain stages of the batch combustion, temperature is not high enough, gas mixing is not good enough and residence time is too short for complete combustion. When placed to a suitable place inside a heating appliance, a catalytic converter can oxidize unburned gases in the flue gas into compounds that are not harmful to the environment. (3 refs.)

  11. Metal release from simulated fixed orthodontic appliances.

    Science.gov (United States)

    Hwang, C J; Shin, J S; Cha, J Y

    2001-10-01

    Most orthodontic appliances and archwires are stainless steel or nickel-titanium (NiTi) alloys that can release metal ions, with saliva as the medium. To measure metal released from the fixed orthodontic appliances currently in use, we fabricated simulated fixed orthodontic appliances that corresponded to half of the maxillary arch and soaked them in 50 mL of artificial saliva (pH 6.75 +/- 0.15, 37 degrees C) for 3 months. We used brackets, tubes, and bands made by Tomy (Tokyo, Japan). Four groups were established according to the appliance manufacturer and the type of metal in the .016 x .022-in archwires. Groups A and B were stainless steel archwires from Ormco (Glendora, Calif) and Dentaurum (Ispringen, Germany), respectively, and groups C and D were both NiTi archwires with Ormco's copper NiTi and Tomy's Bioforce sentalloy, respectively. Stainless steel archwires were heat treated in an electric furnace at 500 degrees C for 1 minute and quenched in water. We measured the amount of metal released from each group by immersion time. Our conclusions were as follows: (1) there was no increase in the amount of chromium released after 4 weeks in group A, 2 weeks in group B, 3 weeks in group C, and 8 weeks in group D; (2) there was no increase in the amount of nickel released after 2 weeks in group A, 3 days in group B, 7 days in group C, and 3 weeks in group D; and (3) there was no increase in the amount of iron released after 2 weeks in group A, 3 days in group B, and 1 day in groups C and D. In our 3-month-long investigation, we saw a decrease in metal released as immersion time increased.

  12. What's driving energy efficient appliance label awareness and purchase propensity?

    International Nuclear Information System (INIS)

    Mills, Bradford; Schleich, Joachim

    2010-01-01

    The EU appliance energy consumption labeling scheme is a key component of efforts to increase the diffusion of energy-efficient household appliances. In this paper, the determinants of consumer knowledge of the energy label for household appliances and the choice of class-A energy-efficient appliances are jointly estimated using data from a large survey of more than 20,000 German households. The results for five major appliances suggest that lack of knowledge of the energy label can generate considerable bias in both estimates of rates of uptake of class-A appliances and in estimates of the underlying determinants of choice of class-A appliance. Simulations of the choice to purchase a class-A appliance, given knowledge of the labeling framework, reveal that residence characteristics and, in several cases, regional electricity prices strongly increase the propensity to purchase a class-A appliance, but socio-economic characteristics have surprisingly little impact on appliance energy-class choice.

  13. Power grids

    International Nuclear Information System (INIS)

    Viterbo, J.

    2012-01-01

    The implementation of renewable energies represents new challenges for electrical systems. The objective: making power grids smarter so they can handle intermittent production. The advent of smart grids will allow flexible operations like distributing energy in a multidirectional manner instead of just one way and it will make electrical systems capable of integrating actions by different users, consumers and producers in order to maintain efficient, sustainable, economical and secure power supplies. Practically speaking, they associate sensors, instrumentation and controls with information processing and communication systems in order to create massively automated networks. Smart grids require huge investments: for example more than 7 billion dollars have been invested in China and in the Usa in 2010 and France is ranked 9. worldwide with 265 million dollars invested. It is expected that smart grids will promote the development of new business models and a change in the value chain for energy. Decentralized production combined with the probable introduction of more or less flexible rates for sales or purchases and of new supplier-customer relationships will open the way to the creation of new businesses. (A.C.)

  14. Turning the appliance market around towards A++

    Energy Technology Data Exchange (ETDEWEB)

    Noergaard, Joergen S.; Guldbrandsen, Tom [Dept. of Civil Engineering, Technical Univ. of Denmark (Denmark); Brange, Birgitte; Karbo, Peter [Elsparefonden (Denmark)

    2007-07-01

    In an effort to exploit better the labelling schemes for appliances the Danish Electricity Saving Trust has run some campaigns on cold appliances. In 1999 focus was on getting people to choose A-rated models, the 2004 campaign focussed on A+, and in 2005 on A++. These campaigns and their results are described in the paper and some conclusions are drawn.The campaigns have consisted of various elements, namely 1) a general information about the campaigns, 2) a subsidy offered temporarily during some months to people buying the A, A+ and A++ models, 3) a website where people can easily find the most energy efficient model within their specification, and 4) in the website are also listed the shops, where consumers can get the appliances at lowest prices. The latter was the most innovative and maybe also the most effective measure in the package.Results showed up as a permanent U-turn of the market in the course of a few years. Where models C, D, E earlier dominated the market, the A, A+ and A++, came to dominate as the standard models in stock. Consequently, their prices dropped significantly. The theory of a rational market behavior is based on some assumptions, one being that full information is available to all actors. The website identifying to the consumers the shops with the lowest priced efficient models was a step in that direction, and the result did not fail to turn up.

  15. Switch green : Energy Star appliance feebate

    International Nuclear Information System (INIS)

    2007-01-01

    Between 1990 and 2004, greenhouse gas (GHG) emissions from the residential sector have grown by 10 per cent, and are likely to continue growing unless a policy aimed at reducing emissions is introduced. The residential sector is a significant contributor to Canada's overall GHG emissions, and an important source for potential reductions. This report presented the results of a study that described and evaluated a new economic instrument aimed at reducing greenhouse gas (GHG) emissions and energy consumption in Canada from household appliances, such as air conditioners, furnaces and boilers. Results of a quantitative analysis to determine the effect of changing taxation of residential appliances to reflect energy consumption and greenhouse gas emissions were presented. In addition, the report presented the results of a qualitative evaluation of the policy, using the criteria established in the 2005 budget plan, a framework for evaluating environmental tax proposals. The report outlined the context for the tax proposal that was evaluated and provided a summary of trends in Canada's greenhouse gas emissions and energy consumption as well as a discussion of important trends in residential energy consumption. A review of policies already in place to address energy consumption from household appliances was also presented. 11 tabs., 6 figs

  16. Measure Guideline: Combustion Safety for Natural Draft Appliances Through Appliance Zone Isolation

    Energy Technology Data Exchange (ETDEWEB)

    Fitzgerald, J. [Center for Energy and Environment, Minneapolis, MN (United States); Bohac, D. [Center for Energy and Environment, Minneapolis, MN (United States)

    2014-04-01

    This measure guideline covers how to assess and carry out the isolation of natural draft combustion appliances from the conditioned space of low-rise residential buildings. It deals with combustion appliances located either within the living space in enclosed closets or side rooms or outside the living space in an adjacent area like an attic or garage. This subset of houses does not require comprehensive combustion safety tests and simplified prescriptive procedures can be used to address safety concerns. This allows residential energy retrofit contractors inexperienced in advanced combustion safety testing to effectively address combustion safety issues and allow energy retrofits including tightening and changes to distribution and ventilation systems to proceed.

  17. Environmentally Friendly Machining

    CERN Document Server

    Dixit, U S; Davim, J Paulo

    2012-01-01

    Environment-Friendly Machining provides an in-depth overview of environmentally-friendly machining processes, covering numerous different types of machining in order to identify which practice is the most environmentally sustainable. The book discusses three systems at length: machining with minimal cutting fluid, air-cooled machining and dry machining. Also covered is a way to conserve energy during machining processes, along with useful data and detailed descriptions for developing and utilizing the most efficient modern machining tools. Researchers and engineers looking for sustainable machining solutions will find Environment-Friendly Machining to be a useful volume.

  18. Measurement of HTO permeability of materials for protective appliances

    International Nuclear Information System (INIS)

    Yamamoto, H.; Tomooka, M.; Kato, S.; Murata, M.; Kinouchi, N.; Yamamoto, H.

    1992-01-01

    Tritiated water (HTO) vapor permeabilities were measured for plastic and rubber films used for protective appliances (suits, gloves, wrappings, etc.). The measurement data prove that polyehylene and butyl rubbers are materials suitable for HTO protective appliances with their lower permeability. The data also indicate that desiccating protective appliances before reuse is effective for restoring their original resistances to penetrating HTO vapor when they are repeatedly used. (author)

  19. Electric household appliances lighting. Synthesis; Electromenager eclairage. Note de synthese

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-09-01

    This study has been realized on 10000 families in order to know the French behavior concerning the electric household appliances and the lighting of their accommodation. The document presents statistically the answers to the questions on the electric household in the accommodation, the choice criteria, the use conditions, the washing temperatures, the nature of the electric household appliances, the microwave ovens, the influence of the energy-label on the appliances and the lighting. (A.L.B.)

  20. Hydrophilic structures for condensation management in refrigerator appliances

    Science.gov (United States)

    Kuehl, Steven John; Vonderhaar, John J; Wu, Guolian; Wu, Mianxue

    2014-10-21

    A refrigerator appliance that includes a freezer compartment having a freezer compartment door, and a refrigeration compartment having at least one refrigeration compartment door. The appliance further includes a mullion with an exterior surface. The mullion divides the compartments and the exterior surface directs condensation toward a transfer point. The appliance may also include a cabinet that houses the compartments and has two sides, each with an exterior surface. Further, at least one exterior surface directs condensation toward a transfer point.

  1. TIGER: A graphically interactive grid system for turbomachinery applications

    Science.gov (United States)

    Shih, Ming-Hsin; Soni, Bharat K.

    1992-01-01

    Numerical grid generation algorithm associated with the flow field about turbomachinery geometries is presented. Graphical user interface is developed with FORMS Library to create an interactive, user-friendly working environment. This customized algorithm reduces the man-hours required to generate a grid associated with turbomachinery geometry, as compared to the use of general-purpose grid generation softwares. Bezier curves are utilized both interactively and automatically to accomplish grid line smoothness and orthogonality. Graphical User Interactions are provided in the algorithm, allowing the user to design and manipulate the grid lines with a mouse.

  2. Grid pulser

    International Nuclear Information System (INIS)

    Jansweijer, P.P.M.; Es, J.T. van.

    1990-01-01

    This report describes a fast pulse generator. This generator delivers a high-voltage pulse of at most 6000 V with a rise time being smaller than 50 nS. this results in a slew rate of more than 120.000 volts per μS. The pulse generator is used to control the grid of the injector of the electron accelerator MEA. The capacity of this grid is about 60 pF. In order to charge this capacity up to 6000 volts in 50 nS a current of 8 ampere is needed. The maximal pulse length is 50 μS with a repeat frequency of 500 Hz. During this 50 μS the stability of the pulse amplitude is better than 0.1%. (author). 20 figs

  3. The grid

    OpenAIRE

    Morrad, Annie; McArthur, Ian

    2018-01-01

    Project Anywhere Project title: The Grid   Artists: Annie Morrad: Artist/Senior Lecturer, University of Lincoln, School of Film and Media, Lincoln, UK   Dr Ian McArthur: Hybrid Practitioner/Senior Lecturer, UNSW Art & Design, UNSW Australia, Sydney, Australia   Annie Morrad is a London-based artist and musician and senior lecturer at the University of Lincoln, UK. Dr Ian McArthur is a Sydney-based hybrid practitione...

  4. 21 CFR 872.5410 - Orthodontic appliance and accessories.

    Science.gov (United States)

    2010-04-01

    ... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Therapeutic Devices § 872.5410 Orthodontic appliance and... device includes the preformed orthodontic band, orthodontic band material, orthodontic elastic band...

  5. Achievement report for fiscal 1998. Development of environmentally friendly universal controller; 1998 nendo kankyo taio universal controller no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    Research and development was carried out for an 'environmentally friendly universal controller (UC)' which would be 'user-friendly and energy-saving' when used with electrical home appliances. An environmentally friendly UC is a remote controller which utilizes an infrared two-way communication function and becomes capable of dealing with any appliance upon downloading remote control information from the appliance involved. Studies were conducted for the development of controller hardware and software therefor and for the development of electrical home appliances to correspond to their specifications. In relation with energy conservation, studies centered about reduction in power consumption while on standby and unnecessary power consumption. As the result, an environmentally friendly UC protocol was newly developed and, based on the protocol, plural numbers of controllers, appliances, and network gateways were tentatively fabricated, and were examined for their function, behavior, and operational interchangeability. Systems aiming at reducing power consumption while on standby and unnecessary power consumption were built by way of experiment, and were checked for performance. It was then concluded that a reduction of several billion kWh might be achieved. (NEDO)

  6. The CrossGrid project

    International Nuclear Information System (INIS)

    Kunze, M.

    2003-01-01

    There are many large-scale problems that require new approaches to computing, such as earth observation, environmental management, biomedicine, industrial and scientific modeling. The CrossGrid project addresses realistic problems in medicine, environmental protection, flood prediction, and physics analysis and is oriented towards specific end-users: Medical doctors, who could obtain new tools to help them to obtain correct diagnoses and to guide them during operations; industries, that could be advised on the best timing for some critical operations involving risk of pollution; flood crisis teams, that could predict the risk of a flood on the basis of historical records and actual hydrological and meteorological data; physicists, who could optimize the analysis of massive volumes of data distributed across countries and continents. Corresponding applications will be based on Grid technology and could be complex and difficult to use: the CrossGrid project aims at developing several tools that will make the Grid more friendly for average users. Portals for specific applications will be designed, that should allow for easy connection to the Grid, create a customized work environment, and provide users with all necessary information to get their job done

  7. Magnetic fields from electric toothbrushes promote corrosion in orthodontic stainless steel appliances but not in titanium appliances.

    Science.gov (United States)

    Kameda, Takashi; Ohkuma, Kazuo; Oda, Hirotake; Sano, Natsuki; Batbayar, Nomintsetseg; Terashima, Yukari; Sato, Soh; Terada, Kazuto

    2013-01-01

    Electric toothbrushes are widely used, and their electric motors have been reported to produce low-frequency electromagnetic fields that induced electric currents in metallic objects worn by the users. In this study, we showed that electric toothbrushes generated low-frequency magnetic fields (MFs) and induced electric currents in orthodontic appliances in artificial saliva (AS), which accelerated corrosion in stainless steel (SUS) appliances, but not in titanium (Ti) appliances; the corrosion was evaluated by using an inductively coupled plasma-optical emission spectrometer and a three-dimensional laser confocal microscope. The pH of AS used for appliance immersion did not change during or after MF exposure. These results suggested that MF-induced currents from electric toothbrushes could erode SUS appliances, but not Ti appliances, because of their high corrosion potentials. Further studies are required to clarify the mechanisms of metallic corrosion by induced currents in dental fields, which may trigger metal allergies in patients.

  8. Safe Grid

    Science.gov (United States)

    Chow, Edward T.; Stewart, Helen; Korsmeyer, David (Technical Monitor)

    2003-01-01

    The biggest users of GRID technologies came from the science and technology communities. These consist of government, industry and academia (national and international). The NASA GRID is moving into a higher technology readiness level (TRL) today; and as a joint effort among these leaders within government, academia, and industry, the NASA GRID plans to extend availability to enable scientists and engineers across these geographical boundaries collaborate to solve important problems facing the world in the 21 st century. In order to enable NASA programs and missions to use IPG resources for program and mission design, the IPG capabilities needs to be accessible from inside the NASA center networks. However, because different NASA centers maintain different security domains, the GRID penetration across different firewalls is a concern for center security people. This is the reason why some IPG resources are been separated from the NASA center network. Also, because of the center network security and ITAR concerns, the NASA IPG resource owner may not have full control over who can access remotely from outside the NASA center. In order to obtain organizational approval for secured remote access, the IPG infrastructure needs to be adapted to work with the NASA business process. Improvements need to be made before the IPG can be used for NASA program and mission development. The Secured Advanced Federated Environment (SAFE) technology is designed to provide federated security across NASA center and NASA partner's security domains. Instead of one giant center firewall which can be difficult to modify for different GRID applications, the SAFE "micro security domain" provide large number of professionally managed "micro firewalls" that can allow NASA centers to accept remote IPG access without the worry of damaging other center resources. The SAFE policy-driven capability-based federated security mechanism can enable joint organizational and resource owner approved remote

  9. Grid interoperability: joining grid information systems

    International Nuclear Information System (INIS)

    Flechl, M; Field, L

    2008-01-01

    A grid is defined as being 'coordinated resource sharing and problem solving in dynamic, multi-institutional virtual organizations'. Over recent years a number of grid projects, many of which have a strong regional presence, have emerged to help coordinate institutions and enable grids. Today, we face a situation where a number of grid projects exist, most of which are using slightly different middleware. Grid interoperation is trying to bridge these differences and enable Virtual Organizations to access resources at the institutions independent of their grid project affiliation. Grid interoperation is usually a bilateral activity between two grid infrastructures. Recently within the Open Grid Forum, the Grid Interoperability Now (GIN) Community Group is trying to build upon these bilateral activities. The GIN group is a focal point where all the infrastructures can come together to share ideas and experiences on grid interoperation. It is hoped that each bilateral activity will bring us one step closer to the overall goal of a uniform grid landscape. A fundamental aspect of a grid is the information system, which is used to find available grid services. As different grids use different information systems, interoperation between these systems is crucial for grid interoperability. This paper describes the work carried out to overcome these differences between a number of grid projects and the experiences gained. It focuses on the different techniques used and highlights the important areas for future standardization

  10. Semantic Description of IoT Security for Smart Grid

    OpenAIRE

    Ayele, Getinet

    2017-01-01

    Master's thesis Information- and communication technology IKT590 - University of Agder 2017 This research work proposed, developed and evaluated IoT Security ontology for smart home energy management system (SHEMS) in smart grids. The ontology description includes infrastructure, attacks, vulnerabilities and counter measures for the main components of SHEMS such as Smart Meter, Smart Appliance, Home Gateway, and Billing data. The ontology extends the SAREF energy management ontology with s...

  11. Dynamic virtual AliEn Grid sites on Nimbus with CernVM

    International Nuclear Information System (INIS)

    Harutyunyan, A; Buncic, P; Freeman, T; Keahey, K

    2010-01-01

    We describe the work on enabling one click deployment of Grid sites of AliEn Grid framework on the Nimbus 'science cloud' at the University of Chicago. The integration of computing resources of the cloud with the resource pool of AliEn Grid is achieved by leveraging two mechanisms: the Nimbus Context Broker developed at Argonne National Laboratory and the University of Chicago, and CernVM - a baseline virtual software appliance for LHC experiments developed at CERN. Two approaches of dynamic virtual AliEn Grid site deployment are presented.

  12. Effects of mandibular protraction appliance associated to fixed appliance in adults

    Directory of Open Access Journals (Sweden)

    Bruno D'Aurea Furquim

    2013-10-01

    Full Text Available OBJECTIVE: This retrospective study aimed to conduct a cephalometric evaluation of the skeletal, dental and soft tissue effects resulting from treatment of adult patients presenting Class II malocclusion, performed with a Mandibular Protraction Appliance (MPA combined with a fixed orthodontic appliance. METHODS: The sample consisted of teleradiographs obtained before and after treatment of 9 adult patients (initial mean age of 22.48 years with bilateral Class II, division 1, malocclusion. Paired t test (p < 0.05 was applied to compare initial and final values. RESULTS: t test revealed an increase in anteroinferior facial height and posterior facial height. The dental changes include: extrusion of upper incisors, buccal inclination, protrusion of lower incisors, mesialization and extrusion of mandibular molars. Regarding the soft tissue component, there was an increase in nasolabial angle in addition to upper lip retrusion. CONCLUSIONS: The effects of treating Class II malocclusion adult patients, by means of using Mandibular Protraction Appliance (MPA combined with a fixed appliance were mostly observed in the mandibular arch, and consisted of buccal inclination, protrusion and intrusion of incisors, and mesialization and extrusion of the molars.

  13. Oral appliances and functional orthopaedic appliances for obstructive sleep apnoea in children.

    Science.gov (United States)

    Carvalho, Fernando R; Lentini-Oliveira, Débora A; Prado, Lucila Bf; Prado, Gilmar F; Carvalho, Luciane Bc

    2016-10-05

    Apnoea is a breathing disorder marked by the absence of airflow at the nose or mouth. In children, risk factors include adenotonsillar hypertrophy, obesity, neuromuscular disorders and craniofacial anomalies. The most common treatment for obstructive sleep apnoea syndrome (OSAS) in childhood is adeno-tonsillectomy. This approach is limited by its surgical risks, mostly in children with comorbidities and, in some patients, by recurrence that can be associated with craniofacial problems. Oral appliances and functional orthopaedic appliances have been used for patients who have OSAS and craniofacial anomalies because they hold the lower jaw (mandible) forwards which potentially enlarges the upper airway and increases the upper airspace, improving the respiratory function. To assess the effects of oral appliances or functional orthopaedic appliances for obstructive sleep apnoea in children. We searched the following electronic databases: Cochrane Oral Health's Trials Register (to 7 April 2016); Cochrane Central Register of Controlled Trials (CENTRAL; 2016, Issue 3) in the Cochrane Library (searched 7 April 2016); MEDLINE Ovid (1946 to 7 April 2016); Embase Ovid (1980 to 7 April 2016); LILACS BIREME (from 1982 to 7 April 2016); BBO BIREME (from 1986 to 7 April 2016) and SciELO Web of Science (from 1997 to 7 April 2016). We searched ClinicalTrials.gov and the World Health Organization International Clinical Trials Registry Platform for ongoing trials on 7 April 2016. We placed no restrictions on the language or date of publication when searching the electronic databases. All randomised or quasi-randomised controlled trials comparing all types of oral and functional orthopaedic appliances with placebo or no treatment, in children 15 years old or younger. reduction of apnoea to less than one episode per hour. dental and skeletal relationship, sleep parameters improvement, cognitive and phonoaudiological function, behavioural problems, quality of life, side effects

  14. A Review of Systems and Technologies for Smart Homes and Smart Grids

    OpenAIRE

    Lobaccaro, Gabriele; Carlucci, Salvatore; Löfström, Erica

    2016-01-01

    In the actual era of smart homes and smart grids, advanced technological systems that allow the automation of domestic tasks are developing rapidly. There are numerous technologies and applications that can be installed in smart homes today. They enable communication between home appliances and users, and enhance home appliances’ automation, monitoring and remote control capabilities. This review article, by introducing the concept of the smart home and the advent of the smart grid, investiga...

  15. Experiences and behaviors of end-users in a smart grid: the influence of values, attitudes, trust, and several types of demand side management

    NARCIS (Netherlands)

    Wiekens, Carina; Grootel, Maike; Steinmeijer, Sophie

    2014-01-01

    In this research, the experiences and behaviors of end-users in a smart grid project are explored. In PowerMatching City, the leading Dutch smart grid project, 40 households were equipped with various decentralized energy sources (PV and microCHP), hybrid heat pumps, smart appliances, smart meters

  16. Appliance choice functions in Canadian households. Paper no. IGEC-1-ID02

    International Nuclear Information System (INIS)

    Aydinalp, M.; Fung, A.; Ugursal, V.I.

    2005-01-01

    Decisions regarding the purchase of various types of major household appliances are influenced by the economic and demographic characteristics of households, i.e., appliance customers. It is therefore necessary to understand the relationship between these characteristics and the decisions made regarding the purchase of appliances to be able to predict future trends in appliance purchases, and consequently, the future appliance energy consumption of the national stock of appliances. In this paper, a methodology is presented to develop choice functions for the purchase of new major household appliances. This methodology is used to develop appliance choice functions for Canada. (author)

  17. Convex stoma appliances: an audit of stoma care nurses.

    Science.gov (United States)

    Perrin, Angie

    2016-12-08

    This article observes the complexities surrounding the use of convex appliances within the specialist sphere of stoma care. It highlights some of the results taken from a small audit carried out with 24 stoma care nurses examining the general use of convex appliances and how usage of convex products has evolved, along with specialist stoma care practice.

  18. Economical regulation power through load shifting with smart energy appliances

    NARCIS (Netherlands)

    Vlot, M.C.; Knigge, J.D.; Slootweg, J.G.

    2013-01-01

    This paper considers the technical and economical feasibility of the introduction of automated demand response from domestic smart appliances in a European setting as a means to create a significant amount of regulating power. Simplified power-time flexibility models for appliances are introduced on

  19. 49 CFR 238.230 - Safety appliances-new equipment.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Safety appliances-new equipment. 238.230 Section... I Passenger Equipment § 238.230 Safety appliances—new equipment. (a) Applicability. This section..., 2007, that is equipped with a safety appliance, required by the “manner of application” provisions in...

  20. 46 CFR 108.580 - Personal lifesaving appliances.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Personal lifesaving appliances. 108.580 Section 108.580 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Lifesaving Equipment § 108.580 Personal lifesaving appliances. (a) Lifebuoys. Each unit...

  1. 46 CFR 108.645 - Markings on lifesaving appliances.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Markings on lifesaving appliances. 108.645 Section 108.645 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Equipment Markings and Instructions § 108.645 Markings on lifesaving appliances. (a...

  2. 49 CFR 238.229 - Safety appliances-general.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Safety appliances-general. 238.229 Section 238.229... Equipment § 238.229 Safety appliances—general. (a) Except as provided in this part, all passenger equipment continues to be subject to the safety appliance requirements contained in Federal statute at 49 U.S.C...

  3. 46 CFR 133.70 - Personal lifesaving appliances.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Personal lifesaving appliances. 133.70 Section 133.70 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OFFSHORE SUPPLY VESSELS LIFESAVING SYSTEMS Requirements for All OSVs § 133.70 Personal lifesaving appliances. (a) Lifebuoys. Each OSV must...

  4. 46 CFR 108.665 - Appliances for watertight integrity.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Appliances for watertight integrity. 108.665 Section 108.665 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Equipment Markings and Instructions § 108.665 Appliances for watertight integrity...

  5. A comparative study of two-piece ostomy appliances.

    Science.gov (United States)

    Welser, Marion; Riedlinger, Inge; Prause, Ulla

    The quality of life of people with a stoma may be affected by peristomal skin disorders and by frequent unplanned changes of ostomy appliances due to problems with those appliances. The aim of this study was to evaluate two new, two-piece ostomy appliances with mechanical couplings (both from the SenSura range by Coloplast) and their ability to address areas that may be important to the quality of life of people with stomas, including appliance changes, stool seepage and overfilling. The study design featured two comparative, crossover, randomized multi-centre studies that were conducted in Germany. The SenSura appliances were evaluated against established reference appliances. Seventy-three individuals with a colostomy (closed-end appliances) and 75 individuals with an ileostomy (drainable appliances) participated in the studies. The participants tested 4-6 flanges of each type within a maximum period of two weeks. The results demonstrated that there was less seepage of stool observed under the SenSura flange when it was removed (pappliances. The SenSura flanges had better adhesion and flexibility and were easier to remove than the references (pappliances on quality of life indicators - there were fewer unplanned changes and less seepage of stool was observed in patients using the SenSura products.

  6. 33 CFR 81.20 - Lights and sound signal appliances.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Lights and sound signal appliances. 81.20 Section 81.20 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY... appliances. Each vessel under the 72 COLREGS, except the vessels of the Navy, is exempt from the requirements...

  7. DC Home Appliances for DC Distribution System

    Directory of Open Access Journals (Sweden)

    MUHAMMAD KAMRAN

    2017-10-01

    Full Text Available This paper strengthens the idea of DC distribution system for DC microgrid consisting of a building of 50 apartments. Since the war of currents AC system has been dominant because of the paucity of research in the protection of the DC system. Now with the advance research in power electronics material and components, generation of electricity is inherently DC as by solar PV, fuel cell and thermoelectric generator that eliminates the rectification process. Transformers are replaced by the power electronics buck-boost converters. DC circuit breakers have solved the protection problems for both DC transmission and distribution system. In this paper 308V DC microgrid is proposed and home appliances (DC internal are modified to operate on 48V DC from DC distribution line. Instead of using universal and induction motors in rotary appliances, BLDC (Brushless DC motors are proposed that are highly efficient with minimum electro-mechanical and no commutation losses. Proposed DC system reduces the power conversion stages, hence diminishes the associated power losses and standby losses that boost the overall system efficiency. So in view of all this a conventional AC system can be replaced by a DC system that has many advantages by cost as well as by performance

  8. Incorporating Experience Curves in Appliance Standards Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Garbesi, Karina; Chan, Peter; Greenblatt, Jeffery; Kantner, Colleen; Lekov, Alex; Meyers, Stephen; Rosenquist, Gregory; Buskirk, Robert Van; Yang, Hung-Chia; Desroches, Louis-Benoit

    2011-10-31

    The technical analyses in support of U.S. energy conservation standards for residential appliances and commercial equipment have typically assumed that manufacturing costs and retail prices remain constant during the projected 30-year analysis period. There is, however, considerable evidence that this assumption does not reflect real market prices. Costs and prices generally fall in relation to cumulative production, a phenomenon known as experience and modeled by a fairly robust empirical experience curve. Using price data from the Bureau of Labor Statistics, and shipment data obtained as part of the standards analysis process, we present U.S. experience curves for room air conditioners, clothes dryers, central air conditioners, furnaces, and refrigerators and freezers. These allow us to develop more representative appliance price projections than the assumption-based approach of constant prices. These experience curves were incorporated into recent energy conservation standards for these products. The impact on the national modeling can be significant, often increasing the net present value of potential standard levels in the analysis. In some cases a previously cost-negative potential standard level demonstrates a benefit when incorporating experience. These results imply that past energy conservation standards analyses may have undervalued the economic benefits of potential standard levels.

  9. Corrosion of weldments in orthodontic appliances

    International Nuclear Information System (INIS)

    Vazquez, S.M.; Riesgo, O.; Duffo, G.S.

    1997-01-01

    The study of corrosion-related problems of dental materials has undergone a considerable development in recent years in order to avoid the use of materials with insufficient corrosion resistance in patients mouth. The subject of the present work was to study a particular type of corrosion: galvanic corrosion. One of the most common case of galvanic couples in patients mouth are the orthodontic appliances. The materials studied in the present work were stainless steel strips and silver-copper wires, isolated and welded between them. The electrochemical tests were performed in a NaCl 0.1M and Lactic Acid 0.1 M solution (pH2.3), and after test, the specimens were observed using the optical and scanning electron microscope. The results show that when stainless steel is coupled with a silver solder, the last is the anode of the galvanic couple. As a consequence of this, the silver solder undergone a severe attack. Stainless steel orthodontic appliances with silver solder are feasibly destroyed due to a severe attack on the filler metal disjoining the welded parts. (author) 9 refs

  10. Optimized Energy Management of a Single-House Residential Micro-Grid With Automated Demand Response

    DEFF Research Database (Denmark)

    Anvari-Moghaddam, Amjad; Monsef, Hassan; Rahimi-Kian, Ashkan

    2015-01-01

    In this paper, an intelligent multi-objective energy management system (MOEMS) is proposed for applications in residential LVAC micro-grids where households are equipped with smart appliances, such as washing machine, dishwasher, tumble dryer and electric heating and they have the capability...

  11. Grid integration and smart grid implementation of emerging technologies in electric power systems through approximate dynamic programming

    OpenAIRE

    Xiao, Jingjie

    2013-01-01

    A key hurdle for implementing real-time pricing of electricity is a lack of con-sumers’ responses. Solutions to overcome the hurdle include the energy management system that automatically optimizes household appliance usage such as plug-in hybrid electric vehicle charging (and discharging with vehicle-to-grid) via a two-way com-munication with the grid. Real-time pricing, combined with household automation devices, has a potential to accommodate an increasing penetration of plug-in hybrid ele...

  12. Implementing peak load reduction algorithms for household electrical appliances

    International Nuclear Information System (INIS)

    Dlamini, Ndumiso G.; Cromieres, Fabien

    2012-01-01

    Considering household appliance automation for reduction of household peak power demand, this study explored aspects of the interaction between household automation technology and human behaviour. Given a programmable household appliance switching system, and user-reported appliance use times, we simulated the load reduction effectiveness of three types of algorithms, which were applied at both the single household level and across all 30 households. All three algorithms effected significant load reductions, while the least-to-highest potential user inconvenience ranking was: coordinating the timing of frequent intermittent loads (algorithm 2); moving period-of-day time-flexible loads to off-peak times (algorithm 1); and applying short-term time delays to avoid high peaks (algorithm 3) (least accommodating). Peak reduction was facilitated by load interruptibility, time of use flexibility and the willingness of users to forgo impulsive appliance use. We conclude that a general factor determining the ability to shift the load due to a particular appliance is the time-buffering between the service delivered and the power demand of an appliance. Time-buffering can be ‘technologically inherent’, due to human habits, or realised by managing user expectations. There are implications for the design of appliances and home automation systems. - Highlights: ► We explored the interaction between appliance automation and human behaviour. ► There is potential for considerable load shifting of household appliances. ► Load shifting for load reduction is eased with increased time buffering. ► Design, human habits and user expectations all influence time buffering. ► Certain automation and appliance design features can facilitate load shifting.

  13. Smart Grid enabled heat pumps

    DEFF Research Database (Denmark)

    Carmo, Carolina; Detlefsen, Nina; Nielsen, Mads Pagh

    2014-01-01

    The transition towards a 100 % fossil-free energy system, while achieving extreme penetration levels of intermittent wind and solar power in electricity generation, requires demand-side technologies that are smart (intermittency-friendly) and efficient. The integration of Smart Grid enabling...... with an empirical study in order to achieve a number of recommendations with respect to technology concepts and control strategies that would allow residential vapor-compression heat pumps to support large-scale integration of intermittent renewables. The analysis is based on data gathered over a period of up to 3...

  14. User friendly packaging

    DEFF Research Database (Denmark)

    Geert Jensen, Birgitte

    2010-01-01

    Most consumers have experienced occasional problems with opening packaging. Tomato sauce from the tinned mackerel splattered all over the kitchen counter, the unrelenting pickle jar lid, and the package of sliced ham that cannot be opened without a knife or a pair of scissors. The research project...... “User-friendly Packaging” aims to create a platform for developing more user-friendly packaging. One intended outcome of the project is a guideline that industry can use in development efforts. The project also points the way for more extended collaboration between companies and design researchers. How...... can design research help industry in packaging innovation?...

  15. Crew appliance concepts. Volume 4, appendix C: Modular space station appliances supporting engineering data. [food management and personal hygiene

    Science.gov (United States)

    Proctor, B. W.; Reysa, R. P.; Russell, D. J.

    1975-01-01

    Data collected for the appliances considered for the space station are presented along with plotted and tabulated trade study results for each appliance. The food management, and personal hygiene data are applicable to a six-man mission of 180-days.

  16. Crew appliance concepts. Volume 2, appendix B: Shuttle orbiter appliances supporting engineering data. [food management and personal hygiene

    Science.gov (United States)

    Proctor, B. W.; Reysa, R. P.; Russell, D. J.

    1975-01-01

    Technical data collected for the food management and personal hygiene appliances considered for the shuttle orbiter are presented as well as plotted and tabulated trade study results for each appliance. Food storage, food operation, galley cleanup, waste collection/transfer, body cleansing, and personal grooming were analyzed.

  17. Smart Grid: Smart Customer Policy Needs

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2011-07-01

    In September 2010, the International Energy Agency (IEA) held a workshop on the regulatory, market and consumer policies necessary to ensure that smart grids are deployed with adequate consideration of their risks and benefits to all stakeholders. This was one of several workshops that brought together energy providers, network operators, technology developers, regulators, customers and government policy makers to discuss smart grid technology and policy. The Smart Grid - Smart Customer Policies workshop allowed stakeholders to: gain a perspective on key issues and barriers facing early deployment of smart grids; hear expert opinion on regulatory, consumer and market challenges to smart grids; discuss smart grid-smart customer policy priorities; and build consensus on the technology and policy ingredients needed for customer-friendly smart grid deployments. Drawing on workshop discussions, the following paper lays out a logical framework to maximise the benefits and minimise the risks that smart grids pose for customers. The paper also describes key policy research questions that will guide future IEA research on this topic.

  18. Optimal Scheduling of Domestic Appliances via MILP

    Directory of Open Access Journals (Sweden)

    Zdenek Bradac

    2014-12-01

    Full Text Available This paper analyzes a consumption scheduling mechanism for domestic appliances within a home area network. The aim of the proposed scheduling is to minimize the total energy price paid by the consumer and to reduce power peaks in order to achieve a balanced daily load schedule. An exact and computationally efficient mixed-integer linear programming (MILP formulation of the problem is presented. This model is verified by several problem instances. Realistic scenarios based on the real price tariffs commercially available in the Czech Republic are calculated. The results obtained by solving the optimization problem are compared with a simulation of the ripple control service currently used by many domestic consumers in the Czech Republic.

  19. Oral health with fixed appliances orthodontics

    Directory of Open Access Journals (Sweden)

    Konta, Brigitte

    2008-03-01

    Full Text Available Orthodontic treatment represents an important fraction in dental interventions. According to other medical methods the question for scientific evidence for the effectiveness of these treatments arises. The question of the effectiveness is connected with the question what is understood as an effect. In principle, the effect of the intervention is understood on the basis of the occlusion or dental health, what disregards further functions of oral health. The generalization to oral health is therefore a necessary consideration in science now. If one appreciates this further development, then there is no one single randomised study available which examines the long-term effect of the orthodontic intervention or for the effects on the oral health. The question, whether the application of a fixed appliance in an orthodontic treatment causes a long-term improvement in oral health, cannot be answered at the present time. The scientific status is the definition of oral health at present. Also the question, whether in the long run the dental health can be improved by fixed appliances cannot be answered with a quality usually achieved by evidence-based medicine. Whether correction of a dental malposition is an effective prerequisite for the preservation of the natural teeth, cannot be answered. There is no generalizing study with sufficient scientific background for Europe or Germany to this topic. The risk for caries cannot be quantified. Caries is identified as a central topic in general but due to numerous factors influencing the risk it is not quantified. The question of the indications is completely open from the scientific literature. For the question of the therapy need or therapy priority some indexes were developed, which lead to a quantification. These indices however are fundamentally criticised by recent research in their meaning and the empirical relevance. There is an impression that there exists a big gap between the practical application

  20. Hot surface temperatures of domestic appliances.

    Science.gov (United States)

    Bassett, Malcolm; Arild, Anne-Helene

    2002-09-01

    Domestic appliances are burning people. In the European Union, accidents requiring hospital treatment due to burns from hot objects account for between 0 and 1% of all such accidents. Young children are particularly at risk. These reported accidents requiring hospital treatment are also likely to be a small proportion of the total number of burns from hot objects. There is a lack of hard evidence about the level of accidents, typical consumer expectation and use, and on the state of the art of appliances. Results of technical laboratory tests carried out on products are used to demonstrate the state of the art and also show how consumer expectations could be changing. Results of a survey into accidents, based on a written questionnaire following telephone contact, provide information on non-hospital cases. Results of tests on products show that there are significant differences in the temperatures of touchable surfaces, even in products of the same type. Typically, these differences are due to variations in design and/or materials of construction. Some products are hot enough to burn skin. Accident research indicates that non-hospital medical practices are treating burn injuries, which are therefore not being included into the current accident statistics. For products with the same function, some types of design or materials of construction are safer, with lower surface temperatures. Many product standards have no or unnecessarily high limits on surface temperatures. Many standards do not address the realities of who is using their products, for what purpose or where they are located. Some standards use unreasonable general limitations and exclusions that allow products with higher surface temperatures than they should have. Many standards rely on the experience factor for avoiding injury that is no longer valid, with the increased availability of safer products of the same type. A major field of work ahead is to carry out more surveys and in-depth studies of non

  1. Decision-making in electrical appliance use in the home

    International Nuclear Information System (INIS)

    Yamamoto, Yoshihiro; Suzuki, Akihiko; Fuwa, Yasuhiro; Sato, Tomohiro

    2008-01-01

    This paper presents the results of a survey as well as an argument from the viewpoint of behavioral economics with the aim of clarifying how consumers make decisions about electrical appliance use in the home. A survey of consumers showed that most have little awareness of the energy efficiency of appliances, the price of the services produced by electrical appliances, or electricity rates. These findings indicate that price does not function as a signal in electricity consumption through electrical appliance use. Rather, we found that consumer decision-making in electricity consumption is dependent on the characteristics of the particular electrical appliances they use. Additionally, we argue that the payment system for home electricity consumption plays an important role in decision-making, causing biases due to aspects of human psychology discussed here in terms of satisficing and heuristics, payment decoupling, and budgeting. We conclude that decision-making about electrical appliance use and electricity consumption in the home is not always rational and is affected both by the particular characteristics of appliances and the payment system for electricity consumption along with human psychology

  2. Unilateral maxillary molar distalization with zygoma-gear appliance.

    Science.gov (United States)

    Kilkis, Dogan; Bayram, Mehmet; Celikoglu, Mevlut; Nur, Metin

    2012-08-01

    The aim of this study was to present the orthodontic treatment of a 15-year-old boy with a unilateral maxillary molar distalization system, called the zygoma-gear appliance. It consisted of a zygomatic anchorage miniplate, an inner bow, and a Sentalloy closed coil spring (GAC International, Bohemia, NY). A distalizing force of 350 g was used during the distalization period. The unilateral Class II malocclusion was corrected in 5 months with the zygoma-gear appliance. The maxillary left first molar showed distalization of 4 mm with an inclination of 3°. The maxillary premolars moved distally with the help of the transseptal fibers. In addition, there were slight decreases in overjet (-0.5 mm) and maxillary incisor inclination (-1°), indicating no anchorage loss from the zygoma-gear appliance. Preadjusted fixed appliances (0.022 × 0.028-in, MBT system; 3M Unitek, Monrovia, Calif) were placed in both arches to achieve leveling and alignment. After 14 months of unilateral distalization with the zygoma-gear appliance and fixed appliances, Class I molar and canine relationships were established with satisfactory interdigitation of the posterior teeth. Acceptable overjet and overbite were also achieved. This article shows that this new system, the zygoma-gear appliance, can be used for unilateral maxillary molar distalization without anchorage loss. Copyright © 2012 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

  3. Electrical field of electrical appliances versus distance: A preliminary analysis

    International Nuclear Information System (INIS)

    Mustafa, Nur Badariah Ahmad; Nordin, Farah Hani; Ismail, Fakaruddin Ali Ahmad; Alkahtani, Ammar Ahmed; Balasubramaniam, Nagaletchumi; Hock, Goh Chin; Shariff, Z A M

    2013-01-01

    Every household electrical appliance that is plugged in emits electric field even if it is not operating. The source where the appliance is plugged into and the components of household electrical appliance contribute to electric field emission. The electric field may cause unknown disturbance to the environment or also affect the human health and the effect might depends on the strength of the electric field emitted by the appliance. This paper will investigate the strength of the electric field emitted by four different electrical appliances using spectrum analyser. The strength will be captured at three different distances; (i) 1m (ii) 2m and (iii) 3m and analysis of the strength of the electrical field is done based on the three different distances. The measurement results show that the strength of the electric field is strongest when it is captured at 1m and the weakest at 3m from the electrical appliance. The results proved that the farther an object is located from the electrical appliance; the less effect the magnetic field has.

  4. The MammoGrid Project Grids Architecture

    CERN Document Server

    McClatchey, Richard; Hauer, Tamas; Estrella, Florida; Saiz, Pablo; Rogulin, Dmitri; Buncic, Predrag; Clatchey, Richard Mc; Buncic, Predrag; Manset, David; Hauer, Tamas; Estrella, Florida; Saiz, Pablo; Rogulin, Dmitri

    2003-01-01

    The aim of the recently EU-funded MammoGrid project is, in the light of emerging Grid technology, to develop a European-wide database of mammograms that will be used to develop a set of important healthcare applications and investigate the potential of this Grid to support effective co-working between healthcare professionals throughout the EU. The MammoGrid consortium intends to use a Grid model to enable distributed computing that spans national borders. This Grid infrastructure will be used for deploying novel algorithms as software directly developed or enhanced within the project. Using the MammoGrid clinicians will be able to harness the use of massive amounts of medical image data to perform epidemiological studies, advanced image processing, radiographic education and ultimately, tele-diagnosis over communities of medical "virtual organisations". This is achieved through the use of Grid-compliant services [1] for managing (versions of) massively distributed files of mammograms, for handling the distri...

  5. Friendly network robotics; Friendly network robotics

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This paper summarizes the research results on the friendly network robotics in fiscal 1996. This research assumes an android robot as an ultimate robot and the future robot system utilizing computer network technology. The robot aiming at human daily work activities in factories or under extreme environments is required to work under usual human work environments. The human robot with similar size, shape and functions to human being is desirable. Such robot having a head with two eyes, two ears and mouth can hold a conversation with human being, can walk with two legs by autonomous adaptive control, and has a behavior intelligence. Remote operation of such robot is also possible through high-speed computer network. As a key technology to use this robot under coexistence with human being, establishment of human coexistent robotics was studied. As network based robotics, use of robots connected with computer networks was also studied. In addition, the R-cube (R{sup 3}) plan (realtime remote control robot technology) was proposed. 82 refs., 86 figs., 12 tabs.

  6. Effective Maxillary Protraction with Tandem Traction Bow Appliance

    Directory of Open Access Journals (Sweden)

    Pravin Kumar S Marure

    2014-01-01

    Full Text Available Tandem traction bow appliance (TTBA promotes patient compliance, because it is more esthetic and comfortable than extraoral appliances. TTBA should be used only in case where maxillary deficiency and normal mandible is present. Advantages of it includes good oral hygiene, early treatment of any Class III malocclusion, optimal retention, distribution of the forces for protraction to all maxillary teeth, free mandibular movement. It can be used in conjunction with fixed appliances if necessary. This paper includes two case reports. The treatment results in both the cases demonstrated significant skeletal and dental response to TTBA therapy. Skeletal change was primarily a result of anterior movement of the maxilla.

  7. Pyogenic granuloma: a rare side complication from an orthodontic appliance.

    Science.gov (United States)

    Acharya, Priti N; Gill, Daljit; Lloyd, Tim

    2011-12-01

    This case report discusses a rare side effect associated with the use ofa fixed quad helix orthodontic appliance. A 14-year-old healthy girl presented with a painful enlarging mass on her tongue, which was causing distress to both her and her parents. Investigations confirmed that the mass was a pyogenic granuloma and management involved surgical excision of the mass and removal of the quad helix appliance. At least once previous case associated with an orthodontic quad helix appliance has been reported in the literature.

  8. Research & Development Roadmap for Next-Generation Appliances

    Energy Technology Data Exchange (ETDEWEB)

    Goetzler, William [Navigant Consulting, Inc., Burlington, MA (United States); Sutherland, Timothy [Navigant Consulting, Inc., Burlington, MA (United States); Foley, Kevin [Navigant Consulting, Inc., Burlington, MA (United States)

    2012-03-01

    Appliances present an attractive opportunity for near-term energy savings in existing building, because they are less expensive and replaced more regularly than heating, ventilation, and air-conditioning (HVAC) systems or building envelope components. This roadmap targets high-priority research and development (R&D), demonstration and commercialization activities that could significantly reduce residential appliance energy consumption. The main objective of the roadmap is to seek activities that accelerate the commercialization of high-efficiency appliance technologies while maintaining the competitiveness of American industry. The roadmap identified and evaluated potential technical innovations, defined research needs, created preliminary research and development roadmaps, and obtained stakeholder feedback on the proposed initiatives.

  9. The use of functional appliances in contemporary orthodontic practice.

    Science.gov (United States)

    DiBiase, A T; Cobourne, M T; Lee, R T

    2015-02-16

    Functional appliances have been used for over 100 years in orthodontics to correct Class II malocclusion. During this time numerous different systems have been developed often accompanied by claims of modification and enhancement of growth. Recent clinical evidence has questioned whether they really have a lasting influence on facial growth, their skeletal effects appearing to be short term. However, despite these findings, the clinical effectiveness of these appliances is acknowledged and they can be very useful in the correction of sagittal arch discrepancies. This article will discuss the clinical use of functional appliances, the underlying evidence for their use and their limitations.

  10. MrGrid: a portable grid based molecular replacement pipeline.

    Directory of Open Access Journals (Sweden)

    Jason W Schmidberger

    Full Text Available BACKGROUND: The crystallographic determination of protein structures can be computationally demanding and for difficult cases can benefit from user-friendly interfaces to high-performance computing resources. Molecular replacement (MR is a popular protein crystallographic technique that exploits the structural similarity between proteins that share some sequence similarity. But the need to trial permutations of search models, space group symmetries and other parameters makes MR time- and labour-intensive. However, MR calculations are embarrassingly parallel and thus ideally suited to distributed computing. In order to address this problem we have developed MrGrid, web-based software that allows multiple MR calculations to be executed across a grid of networked computers, allowing high-throughput MR. METHODOLOGY/PRINCIPAL FINDINGS: MrGrid is a portable web based application written in Java/JSP and Ruby, and taking advantage of Apple Xgrid technology. Designed to interface with a user defined Xgrid resource the package manages the distribution of multiple MR runs to the available nodes on the Xgrid. We evaluated MrGrid using 10 different protein test cases on a network of 13 computers, and achieved an average speed up factor of 5.69. CONCLUSIONS: MrGrid enables the user to retrieve and manage the results of tens to hundreds of MR calculations quickly and via a single web interface, as well as broadening the range of strategies that can be attempted. This high-throughput approach allows parameter sweeps to be performed in parallel, improving the chances of MR success.

  11. Study on Semantic Assets for Smart Appliances Interoperability : D-S3: THIRD INTERIM REPORT

    NARCIS (Netherlands)

    Daniele, L.M.; Hartog, F.T.H. den; Roes, J.B.M.

    2015-01-01

    About two thirds of the energy consumed by buildings originates from the residential sectors and thus household appliances. Household appliances or home appliances are electrical/mechanical machines which accomplish some household functions. Nowadays, appliances are not stand-alone systems anymore.

  12. Study on Semantic Assets for Smart Appliances Interoperability : D-S2: SECOND INTERIM REPORT

    NARCIS (Netherlands)

    Daniele, L.M.; Hartog, F.T.H. den; Roes, J.B.M.

    2014-01-01

    About two thirds of the energy consumed by buildings originates from the residential sectors and thus household appliances. Household appliances or home appliances are electrical/mechanical machines which accomplish some household functions. Nowadays, appliances are not stand-alone systems anymore.

  13. Study on Semantic Assets for Smart Appliances Interoperability : D-S1: FIRST INTERIM REPORT

    NARCIS (Netherlands)

    Hartog, F.T.H. den; Daniele, L.M.; Roes, J.B.M.

    2014-01-01

    About two thirds of the energy consumed by buildings originates from the residential sectors and thus household appliances. Household appliances or home appliances are electrical/mechanical machines which accomplish some household functions. Nowadays, appliances are not stand-alone systems anymore.

  14. 46 CFR 31.36-1 - Lifesaving appliances and arrangements-TB/ALL.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 1 2010-10-01 2010-10-01 false Lifesaving appliances and arrangements-TB/ALL. 31.36-1... CERTIFICATION Lifesaving Appliances and Arrangements § 31.36-1 Lifesaving appliances and arrangements—TB/ALL. All lifesaving appliances and arrangements on tank vessels must be in accordance with subchapter W...

  15. 15 CFR 9.3 - Appliances and equipment included in program.

    Science.gov (United States)

    2010-01-01

    ... 15 Commerce and Foreign Trade 1 2010-01-01 2010-01-01 false Appliances and equipment included in... VOLUNTARY LABELING PROGRAM FOR HOUSEHOLD APPLIANCES AND EQUIPMENT TO EFFECT ENERGY CONSERVATION § 9.3 Appliances and equipment included in program. The appliances and equipment included in this program are room...

  16. 46 CFR 174.100 - Appliances for watertight and weathertight integrity.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Appliances for watertight and weathertight integrity... Offshore Drilling Units § 174.100 Appliances for watertight and weathertight integrity. (a) Appliances to... watertight closures for openings in watertight decks and bulkheads. (b) Appliances to insure weathertight...

  17. 14 CFR 21.502 - Approval of materials, parts, and appliances.

    Science.gov (United States)

    2010-01-01

    ... appliances. 21.502 Section 21.502 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF..., Materials, Parts, and Appliances: Import § 21.502 Approval of materials, parts, and appliances. (a) A material, part, or appliance, manufactured in a foreign country with which the United States has an...

  18. 46 CFR 108.114 - Appliances for watertight and weathertight integrity.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Appliances for watertight and weathertight integrity... Appliances for watertight and weathertight integrity. (a) Appliances to ensure watertight integrity include... watertight decks and bulkheads. (b) Appliances to ensure weathertight integrity include weathertight doors...

  19. 14 CFR 21.305 - Approval of materials, parts, processes, and appliances.

    Science.gov (United States)

    2010-01-01

    ..., and appliances. 21.305 Section 21.305 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION..., Parts, Processes, and Appliances § 21.305 Approval of materials, parts, processes, and appliances. Whenever a material, part, process, or appliance is required to be approved under this chapter, it may be...

  20. A Support System for the Electric Appliance Control Using Pose Recognition

    Science.gov (United States)

    Kawano, Takuya; Yamamoto, Kazuhiko; Kato, Kunihito; Hongo, Hitoshi

    In this paper, we propose an electric appliance control support system for aged and bedridden people using pose recognition. We proposed a pose recognition system that distinguishes between seven poses of the user on the bed. First, the face and arm regions of the user are detected by using the skin color. Our system focuses a recognition region surrounding the face region. Next, the higher order local autocorrelation features within the region are extracted. The linear discriminant analysis creates the coefficient matrix that can optimally distinguish among training data from the seven poses. Our algorithm can recognize the seven poses even if the subject wears different clothes and slightly shifts or slants on the bed. From the experimental results, our system achieved an accuracy rate of over 99 %. Then, we show that it possibles to construct one of a user-friendly system.

  1. A retrospective cephalometric investigation of two fixed functional orthodontic appliances in class II treatment: Functional Mandibular Advancer vs. Herbst appliance.

    Science.gov (United States)

    Kinzinger, Gero Stefan Michael; Lisson, Jörg Alexander; Frye, Linda; Gross, Ulrich; Hourfar, Jan

    2018-01-01

    The objective of the study is to compare skeletal and dental changes in class II patients treated with fixed functional appliances (FFA) that pursue different biomechanical concepts: (1) FMA (Functional Mandibular Advancer) from first maxillary molar to first mandibular molar through inclined planes and (2) Herbst appliance from first maxillary molar to lower first bicuspid through a rod-and-tube mechanism. Forty-two equally distributed patients were treated with FMA (21) and Herbst appliance (21), following a single-step advancement protocol. Lateral cephalograms were available before treatment and immediately after removal of the FFA. The lateral cephalograms were analyzed with customized linear measurements. The actual therapeutic effect was then calculated through comparison with data from a growth survey. Additionally, the ratio of skeletal and dental contributions to molar and overjet correction for both FFA was calculated. Data was analyzed by means of one-sample Student's t tests and independent Student's t tests. Statistical significance was set at p appliance were found, intergroup comparisons showed no statistically significant differences. Almost all measurements resulted in comparable changes for both appliances. Statistically significant dental changes occurred with both appliances. Dentoalveolar contribution to the treatment effect was ≥70%, thus always resulting in ≤30% for skeletal alterations. FMA and Herbst appliance usage results in comparable skeletal and dental treatment effects despite different biomechanical approaches. Treatment leads to overjet and molar relationship correction that is mainly caused by significant dentoalveolar changes.

  2. Consumer attitudes and the benefits of smart grid technologies

    Energy Technology Data Exchange (ETDEWEB)

    Ablondi, B. [Parks Associates, Dallas, TX (United States)

    2010-11-15

    This article discussed consumer attitudes regarding the benefits of smart grid technology. Understanding the motivations of consumers and how much they are willing to pay for smart grid technologies allows utilities to tailor their offerings to ensure market success. Surveys revealed that more than 80 percent of consumers are very interested in learning about ways to cut energy expenditures. Most consumers are only willing to pay less than the cost of the special equipment to participate in programs that guarantee cost savings, requiring innovation on the part of both utilities and their vendors to develop viable business models. Remote monitoring systems are a potential residential energy management solution that would increase consumer awareness of energy consumption, but adoption will occur slowly and only after consumer awareness is increased. The segmentation of consumers is necessary for providers to target those with both an interest in and a willingness to pay for an energy monitoring system. Most consumers want to see information on a thermostat with an enhanced display, and there is limited interest in other formats at this time. Consumers are willing to pay a premium for smart appliances, but the premium only amounts to a fraction of the actual cost, leaving no incentive for appliance manufacturers in the absence of tax or utility incentives. It was concluded that consumer attitudes toward smart grid technology are still being formed and that the consumer must be engaged to realize the full benefit of the smart grid in the residential market. 4 figs.

  3. Using Grid for the BABAR Experiment

    International Nuclear Information System (INIS)

    Bozzi, C.

    2005-01-01

    The BaBar experiment has been taking data since 1999. In 2001 the computing group started to evaluate the possibility to evolve toward a distributed computing model in a grid environment. We built a prototype system, based on the European Data Grid (EDG), to submit full-scale analysis and Monte Carlo simulation jobs. Computing elements, storage elements, and worker nodes have been installed at SLAC and at various European sites. A BaBar virtual organization (VO) and a test replica catalog (RC) are maintained in Manchester, U.K., and the experiment is using three EDG testbed resource brokers in the U.K. and in Italy. First analysis tests were performed under the assumption that a standard BaBar software release was available at the grid target sites, using RC to register information about the executable and the produced n-tuples. Hundreds of analysis jobs accessing either Objectivity or Root data files ran on the grid. We tested the Monte Carlo production using a farm of the INFN-grid testbed customized to install an Objectivity database and run BaBar simulation software. First simulation production tests were performed using standard Job Description Language commands and the output files were written on the closest storage element. A package that can be officially distributed to grid sites not specifically customized for BaBar has been prepared. We are studying the possibility to add a user friendly interface to access grid services for BaBar

  4. Lipedema: friend and foe.

    Science.gov (United States)

    Torre, Yanira Sanchez-De la; Wadeea, Rita; Rosas, Victoria; Herbst, Karen L

    2018-03-09

    Background Lipedema is a chronic disorder presenting in women during puberty or other times of hormonal change such as childbirth or menopause, characterized by symmetric enlargement of nodular, painful subcutaneous adipose tissue (fat) in the limbs, sparing the hands, feet and trunk. Healthcare providers underdiagnose or misdiagnose lipedema as obesity or lymphedema. Materials and methods The benefits (friend) and negative aspects (foe) of lipedema were collected from published literature, discussions with women with lipedema, and institutional review board approved evaluation of medical charts of 46 women with lipedema. Results Lipedema is a foe because lifestyle change does not reduce lipedema fat, the fat is painful, can become obese, causes gait and joint abnormalities, fatigue, lymphedema and psychosocial distress. Hypermobility associated with lipedema can exacerbate joint disease and aortic disease. In contrast, lipedema fat can be a friend as it is associated with relative reductions in obesity-related metabolic dysfunction. In new data collected, lipedema was associated with a low risk of diabetes (2%), dyslipidemia (11.7%) and hypertension (13%) despite an obese average body mass index (BMI) of 35.3 ± 1.7 kg/m2. Conclusion Lipedema is a painful psychologically distressing fat disorder, more foe than friend especially due to associated obesity and lymphedema. More controlled studies are needed to study the mechanisms and treatments for lipedema.

  5. Irvine Smart Grid Demonstration, a Regional Smart Grid Demonstration Project

    Energy Technology Data Exchange (ETDEWEB)

    Yinger, Robert [Southern California Edison Company, Rosemead, CA (United States); Irwin, Mark [Southern California Edison Company, Rosemead, CA (United States)

    2015-12-29

    ISGD was a comprehensive demonstration that spanned the electricity delivery system and extended into customer homes. The project used phasor measurement technology to enable substation-level situational awareness, and demonstrated SCE’s next-generation substation automation system. It extended beyond the substation to evaluate the latest generation of distribution automation technologies, including looped 12-kV distribution circuit topology using URCIs. The project team used DVVC capabilities to demonstrate CVR. In customer homes, the project evaluated HAN devices such as smart appliances, programmable communicating thermostats, and home energy management components. The homes were also equipped with energy storage, solar PV systems, and a number of energy efficiency measures (EEMs). The team used one block of homes to evaluate strategies and technologies for achieving ZNE. A home achieves ZNE when it produces at least as much renewable energy as the amount of energy it consumes annually. The project also assessed the impact of device-specific demand response (DR), as well as load management capabilities involving energy storage devices and plug-in electric vehicle charging equipment. In addition, the ISGD project sought to better understand the impact of ZNE homes on the electric grid. ISGD’s SENet enabled end-to-end interoperability between multiple vendors’ systems and devices, while also providing a level of cybersecurity that is essential to smart grid development and adoption across the nation. The ISGD project includes a series of sub-projects grouped into four logical technology domains: Smart Energy Customer Solutions, Next-Generation Distribution System, Interoperability and Cybersecurity, and Workforce of the Future. Section 2.3 provides a more detailed overview of these domains.

  6. Customer service in appliance sales departments of selected ...

    African Journals Online (AJOL)

    Customer service in appliance sales departments of selected prominent retail outlets: store manager, ... A single measurement of customers' perception of service quality in various stores however suggested ... AJOL African Journals Online.

  7. Effect of Fixed Metallic Oral Appliances on Oral Health.

    Science.gov (United States)

    Alnazzawi, Ahmad

    2018-01-01

    There is a substantial proportion of the population using fixed metallic oral appliances, such as crowns and bridges, which are composed of various dental alloys. These restorations may be associated with a number of effects on oral health with variable degrees of severity, to review potential effects of using fixed metallic oral appliances, fabricated from various alloys. The MEDLINE/PubMed database was searched using certain combinations of keywords related to the topic. The search revealed that burning mouth syndrome, oral pigmentation, hypersensitivity and lichenoid reactions, and genotoxic and cytotoxic effects are the major potential oral health changes associated with fixed prosthodontic appliances. Certain oral disorders are associated with the use of fixed metallic oral appliances. Patch test is the most reliable method that can be applied for identifying metal allergy, and the simultaneous use of different alloys in the mouth is discouraged.

  8. Enabling Smart Grid Cosimulation Studies: Rapid Design and Development of the Technologies and Controls

    Energy Technology Data Exchange (ETDEWEB)

    Hansen, Timothy M.; Kadavil, Rahul; Palmintier, Bryan; Suryanarayanan, Siddharth; Maciejewski, Anthony A.; Siegel, Howard Jay; Chong, Edwin K. P.; Hale, Elaine

    2016-03-01

    The 21st century electric power grid is transforming with an unprecedented increase in demand and increase in new technologies. In the United States Energy Independence and Security Act of 2007, Title XIII sets the tenets for modernizing the electricity grid through what is known as the 'Smart Grid Initiative.' This initiative calls for increased design, deployment, and integration of distributed energy resources, smart technologies and appliances, and advanced storage devices. The deployment of these new technologies requires rethinking and re-engineering the traditional boundaries between different electric power system domains.

  9. Esthetic perception of orthodontic appliances by Brazilian children and adolescents.

    Science.gov (United States)

    Kuhlman, Deise Caldas; Lima, Tatiana Araújo de; Duplat, Candice Belchior; Capelli, Jonas

    2016-01-01

    The objective of this present study was to understand how children and adolescents perceive esthetic attractiveness of a variety of orthodontic appliances. It also analyzed preferences according to patients' age, sex and socioeconomic status. A photograph album consisting of eight photographs of different orthodontic appliances and clear tray aligners placed in a consenting adult with pleasing smile was used. A sample of children or adolescents aged between 8 and 17 years old (n = 276) was asked to rate each image for its attractiveness on a visual analog scale. Comparisons between the appliances attractiveness were performed by means of nonparametric statistics with Friedman's test followed by Dunn's multiple comparison post-hoc test. Correlation between appliances and individuals' socioeconomic status, age, sex, and esthetic perception was assessed by means of Spearman's correlation analysis. Attractiveness ratings of orthodontic appliances varied nonsignificantly for children in the following hierarchy: traditional metallic brackets with green elastomeric ligatures > traditional metallic brackets with gray elastomeric ligatures > sapphire esthetic brackets; and for adolescents, as follows: sapphire esthetic brackets > clear aligner without attachments > traditional metallic brackets with green elastomeric ligatures. The correlation between individuals' socioeconomic status and esthetic perception of a given appliance was negative and statistically significant for appliances such as the golden orthodontic brackets and traditional metallic brackets with green elastomeric ligatures. Metal appliances were considered very attractive, whereas aligners were classified as less attractive by children and adolescents. The correlation between esthetic perception and socioeconomic status revealed that individuals with a higher socioeconomic level judged esthetics as the most attractive attribute. For those with higher economic status, golden orthodontic brackets and

  10. Treatment with active orthodontic appliance in adult patient

    OpenAIRE

    Radeska, Ana; Radeski, Josif; Zlatanovska, Katerina; Papakoca, Kiro; Zarkova, Julija

    2012-01-01

    Aim: Showing the efficiency of orthodontic mobile appliance in treatment of adult patient Case summary: The patient A.K. Age 25 years whit forced progenia, bilateral hypodontia of the maxillary incisors and cross bite of 2 mm in front. The patient was treated with active orthodontic appliance whit bitten ridge and down labial arch. The treatment lasted 18 months after which periods is reached normal occlusion with normal overlap in front and closed diastema mediana. The hypodontia of the m...

  11. Estimating Price Elasticity using Market-Level Appliance Data

    Energy Technology Data Exchange (ETDEWEB)

    Fujita, K. Sydny [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2015-08-04

    This report provides and update to and expansion upon our 2008 LBNL report “An Analysis of the Price Elasticity of Demand for Appliances,” in which we estimated an average relative price elasticity of -0.34 for major household appliances (Dale and Fujita 2008). Consumer responsiveness to price change is a key component of energy efficiency policy analysis; these policies influence consumer purchases through price both explicitly and implicitly. However, few studies address appliance demand elasticity in the U.S. market and public data sources are generally insufficient for rigorous estimation. Therefore, analysts have relied on a small set of outdated papers focused on limited appliance types, assuming long-term elasticities estimated for other durables (e.g., vehicles) decades ago are applicable to current and future appliance purchasing behavior. We aim to partially rectify this problem in the context of appliance efficiency standards by revisiting our previous analysis, utilizing data released over the last ten years and identifying additional estimates of durable goods price elasticities in the literature. Reviewing the literature, we find the following ranges of market-level price elasticities: -0.14 to -0.42 for appliances; -0.30 to -1.28 for automobiles; -0.47 to -2.55 for other durable goods. Brand price elasticities are substantially higher for these product groups, with most estimates -2.0 or more elastic. Using market-level shipments, sales value, and efficiency level data for 1989-2009, we run various iterations of a log-log regression model, arriving at a recommended range of short run appliance price elasticity between -0.4 and -0.5, with a default value of -0.45.

  12. Wood-burning appliances and indoor air quality

    Energy Technology Data Exchange (ETDEWEB)

    Levesque, Benoit; Allaire, Sylvain; Gauvin, Denis; Gingras, Suzanne; Rhainds, Marc; Prud' Homme, Henri; Duchesne, Jean-Francois [CHUQ-Centre de Recherche du CHUL, Unite de Recherche en Sante Publique, 2400, d' Estimauville, Beauport, G1E 7G9 Quebec (Canada); Koutrakis, Petros [Harvard School of Public Health, 677 Huntington Avenue, Boston, MA 02115 (United States)

    2001-12-17

    Wood heating represents an interesting economic alternative to electrical or heating oil and gas systems. However, many people are concerned about poor indoor air quality in homes equipped with wood-burning appliances. We conducted a study in the Quebec City region (Canada) to verify the extent of indoor air contamination, and to examine the frequency of respiratory symptoms and illnesses among occupants of wood-heated homes. One child attending primary school (median=8 years old; range=5-14 years old) and an adult (median=37 years old; range=23-52 years old) were recruited in each eligible house. Eligible houses were without known sources of combustion products (smokers, attached garage, oil or gas furnace, gas stove, etc.) except for wood-burning appliance. Out of the 89 houses included in the study, 59 had wood-burning appliances. Formaldehyde, nitrogen dioxide, respirable particles (PM10) and carbon monoxide were measured in a sub-set of 49 houses (41 with a wood-burning appliance and 8 without). The frequency of respiratory symptoms and diseases among participants were documented using a daily symptom diary. Concentrations of contaminants were low in most houses, both with or without a wood-burning appliance. Globally, there was no consistent relationship between the presence of a wood-burning appliance and respiratory morbidity in residents. Nevertheless, residents who mentioned being exposed to fumes emitted by such an appliance reported more respiratory illnesses and symptoms. The presence of animals or molds, and keeping windows closed most of the time in winter were other factors associated with respiratory problems. We conclude that wood burning appears to be a respiratory health risk for occupants if the appliance is not maintained and used properly.

  13. Esthetic perception of orthodontic appliances by Brazilian children and adolescents

    Science.gov (United States)

    Kuhlman, Deise Caldas; de Lima, Tatiana Araújo; Duplat, Candice Belchior; Capelli, Jonas

    2016-01-01

    ABSTRACT Objective: The objective of this present study was to understand how children and adolescents perceive esthetic attractiveness of a variety of orthodontic appliances. It also analyzed preferences according to patients' age, sex and socioeconomic status. Methods: A photograph album consisting of eight photographs of different orthodontic appliances and clear tray aligners placed in a consenting adult with pleasing smile was used. A sample of children or adolescents aged between 8 and 17 years old (n = 276) was asked to rate each image for its attractiveness on a visual analog scale. Comparisons between the appliances attractiveness were performed by means of nonparametric statistics with Friedman's test followed by Dunn's multiple comparison post-hoc test. Correlation between appliances and individuals' socioeconomic status, age, sex, and esthetic perception was assessed by means of Spearman's correlation analysis. Results: Attractiveness ratings of orthodontic appliances varied nonsignificantly for children in the following hierarchy: traditional metallic brackets with green elastomeric ligatures > traditional metallic brackets with gray elastomeric ligatures > sapphire esthetic brackets; and for adolescents, as follows: sapphire esthetic brackets > clear aligner without attachments > traditional metallic brackets with green elastomeric ligatures. The correlation between individuals' socioeconomic status and esthetic perception of a given appliance was negative and statistically significant for appliances such as the golden orthodontic brackets and traditional metallic brackets with green elastomeric ligatures. Conclusion: Metal appliances were considered very attractive, whereas aligners were classified as less attractive by children and adolescents. The correlation between esthetic perception and socioeconomic status revealed that individuals with a higher socioeconomic level judged esthetics as the most attractive attribute. For those with higher

  14. Esthetic perception of orthodontic appliances by Brazilian children and adolescents

    Directory of Open Access Journals (Sweden)

    Deise Caldas Kuhlman

    Full Text Available ABSTRACT Objective: The objective of this present study was to understand how children and adolescents perceive esthetic attractiveness of a variety of orthodontic appliances. It also analyzed preferences according to patients' age, sex and socioeconomic status. Methods: A photograph album consisting of eight photographs of different orthodontic appliances and clear tray aligners placed in a consenting adult with pleasing smile was used. A sample of children or adolescents aged between 8 and 17 years old (n = 276 was asked to rate each image for its attractiveness on a visual analog scale. Comparisons between the appliances attractiveness were performed by means of nonparametric statistics with Friedman's test followed by Dunn's multiple comparison post-hoc test. Correlation between appliances and individuals' socioeconomic status, age, sex, and esthetic perception was assessed by means of Spearman's correlation analysis. Results: Attractiveness ratings of orthodontic appliances varied nonsignificantly for children in the following hierarchy: traditional metallic brackets with green elastomeric ligatures > traditional metallic brackets with gray elastomeric ligatures > sapphire esthetic brackets; and for adolescents, as follows: sapphire esthetic brackets > clear aligner without attachments > traditional metallic brackets with green elastomeric ligatures. The correlation between individuals' socioeconomic status and esthetic perception of a given appliance was negative and statistically significant for appliances such as the golden orthodontic brackets and traditional metallic brackets with green elastomeric ligatures. Conclusion: Metal appliances were considered very attractive, whereas aligners were classified as less attractive by children and adolescents. The correlation between esthetic perception and socioeconomic status revealed that individuals with a higher socioeconomic level judged esthetics as the most attractive attribute. For those

  15. Analysis and improvement of security of energy smart grids

    International Nuclear Information System (INIS)

    Halimi, Halim

    2014-01-01

    The Smart grid is the next generation power grid, which is a new self-healing, self-activating form of electricity network, and integrates power-flow control, increased quality of electricity, and energy reliability, energy efficiency and energy security using information and communication technologies. Communication networks play a critical role in smart grid, as the intelligence of smart grid is built based on information exchange across the power grid. Its two-way communication and electricity flow enable to monitor, predict and manage the energy usage. To upgrade an existing power grid into a smart grid, it requires an intelligent and secure communication infrastructure. Because of that, the main goal of this dissertation is to propose new architecture and implementation of algorithms for analysis and improvement of the security and reliability in smart grid. In power transmission segments of smart grid, wired communications are usually adopted to ensure robustness of the backbone power network. In contrast, for a power distribution grid, wireless communications provide many benefits such as low cost high speed links, easy setup of connections among different devices/appliances, and so on. Wireless communications are usually more vulnerable to security attacks than wired ones. Developing appropriate wireless communication architecture and its security measures is extremely important for a smart grid system. This research addresses physical layer security in a Wireless Smart Grid. Hence a defense Quorum- based algorithm is proposed to ensure physical security in wireless communication. The new security architecture for smart grid that supports privacy-preserving, data aggregation and access control is defined. This architecture consists of two parts. In the first part we propose to use an efficient and privacy-preserving aggregation scheme (EPPA), which aggregates real-time data of consumers by Local Gateway. During aggregation the privacy of consumers is

  16. Semantic Information Modeling for Emerging Applications in Smart Grid

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Qunzhi; Natarajan, Sreedhar; Simmhan, Yogesh; Prasanna, Viktor

    2012-04-16

    Smart Grid modernizes power grid by integrating digital and information technologies. Millions of smart meters, intelligent appliances and communication infrastructures are under deployment allowing advanced IT applications to be developed to secure and manage power grid operations. Demand response (DR) is one such emerging application to optimize electricity demand by curtailing/shifting power load when peak load occurs. Existing DR approaches are mostly based on static plans such as pricing policies and load shedding schedules. However, improvements to power management applications rely on data emanating from existing and new information sources with the growth of Smart Grid information space. In particular, dynamic DR algorithms depend on information from smart meters that report interval-based power consumption measurement, HVAC systems that monitor buildings heat and humidity, and even weather forecast services. In order for emerging Smart Grid applications to take advantage of the diverse data influx, extensible information integration is required. In this paper, we develop an integrated Smart Grid information model using Semantic Web techniques and present case studies of using semantic information for dynamic DR. We show the semantic model facilitates information integration and knowledge representation for developing the next generation Smart Grid applications.

  17. Grid Integration Research | Wind | NREL

    Science.gov (United States)

    Grid Integration Research Grid Integration Research Researchers study grid integration of wind three wind turbines with transmission lines in the background. Capabilities NREL's grid integration electric power system operators to more efficiently manage wind grid system integration. A photo of

  18. Maxillary molar distalization with first class appliance.

    Science.gov (United States)

    Ramesh, Namitha; Palukunnu, Biswas; Ravindran, Nidhi; Nair, Preeti P

    2014-02-27

    Non-extraction treatment has gained popularity for corrections of mild-to-moderate class II malocclusion over the past few decades. The distalization of maxillary molars is of significant value for treatment of cases with minimal arch discrepancy and mild class II molar relation associated with a normal mandibular arch and acceptable profile. This paper describes our experience with a 16-year-old female patient who reported with irregularly placed upper front teeth and unpleasant smile. The patient was diagnosed to have angles class II malocclusion with moderate maxillary anterior crowding, deep bite of 4 mm on a skeletal class II base with an orthognathic maxilla and retrognathic mandible and normal growth pattern. She presented an ideal profile and so molar distalization was planned with the first-class appliance. Molars were distalised by 8 mm on the right and left quadrants and class I molar relation achieved within 4 months. The space gained was utilised effectively to align the arch and establish a class I molar and canine relation.

  19. Intelligent Control of Home Appliances via Network

    DEFF Research Database (Denmark)

    Rossello Busquet, Ana

    platform which guaranties interoperability, as well as scalability and flexibility. Therefore, a home gateway prototype has been developed in JAVA. This implementation offers the required capabilities for a Home Energy Management System, i.e. it enables the user to monitor and control the home devices......, in addition to providing energy management strategies to reduce electricity consumption. Reducing energy consumption in home environments has become crucial to meet the "20-20-20" targets set by European Commission Climate Action. However, reducing energy in home environments is not sufficient. The power grid......This thesis addresses selected topics of energy management in home environments and ICT for the Smart Grid. However, those two topics are vast and only a few aspects of them have been discussed. This thesis focuses on providing a home energy management solution based on a technology independent...

  20. Initial Evaluation of a Titration Appliance for Temporary Treatment of Obstructive Sleep Apnea.

    Science.gov (United States)

    Levendowski, Daniel J; Morgan, Todd; Westbrook, Philip

    2012-01-01

    Custom oral appliances that adjustably advance the mandible provide superior outcomes when treating patients with moderate or severe sleep apnea. Custom appliances, however, are expensive, must be fitted by a dentist, and the likelihood of successful outcomes are difficult to predict. An inexpensive trial appliance, if proven efficacious, might be used to predict custom appliance outcomes or to provide temporary therapeutic benefit. The aim of this initial study was to assess the treatment efficacy of a novel titration oral appliance with that of an optimized custom appliance. Seventeen patients, treated with a custom oral appliance for at least one year, successfully completed a three-night home sleep test. The baseline obstructive sleep apnea severity was established on Night 1 with seven patients exhibiting severe, six moderate and four mild apnea/hypopnea indexes. Patients were randomly assigned to wear their custom appliance or the titration appliance on Nights 2 and 3. Significant reductions in the mean overall and supine apnea indexes (p titration and custom appliances. The proportion of patients who exhibited at least a 50% reduction in the overall apnea index and supine apnea/hypopnea were similar for the titration and custom appliance (~60%). The custom appliance reduced the overall apnea/hypopnea index by 50% in a greater proportion of the patients compared to the titration appliance (77% vs. 53%). The titration appliance significantly reduced the degree of hypoxic exposure across sleep disordered breathing events overall (p titration appliance, but preferred the titration appliance to no therapy. The titration appliance may be useful in assessing oral appliance treatment efficacy. When set to 70% of maximum protrusion, the titration appliance may provide immediate, temporary therapeutic benefit.

  1. Climate friendly dietary guidelines

    DEFF Research Database (Denmark)

    Trolle, Ellen; Mogensen, Lisbeth; Thorsen, Anne Vibeke

    2014-01-01

    The aim of this study was to investigate how the present Danish diet could be changed in a climate friendly direction that follows the recommendations of a healthy diet. The carbon footprint (CF) of an average Danish diet was calculated and compared to CF of a recommended healthy diet by 1......%, if the healthy diet was eaten instead of the average current diet. However, if the diet was climate optimized by choosing foods with a low CF within the food groups; meat, vegetables and fruit, CF of this diet may be reduced by 23 % compared to CF of the average diet....

  2. Distributed Smart Grid Asset Control Strategies for Providing Ancillary Services

    Energy Technology Data Exchange (ETDEWEB)

    Kalsi, Karanjit [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Zhang, Wei [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Lian, Jianming [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Marinovici, Laurentiu D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Moya, Christian [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Dagle, Jeffery E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2013-10-30

    implementing real load control programs. The promise of autonomous, Grid Friendly™ response by smart appliances in the form of under-frequency load shedding was demonstrated in the GridWise Olympic Peninsula Demonstration in 2006. Each controller monitored the power grid voltage signal and requested that electrical load be shed by its appliance whenever electric power-grid frequency fell below 59.95 Hz. The controllers and their appliances responded reliably to each shallow under-frequency event, which was an average of one event per day and shed their loads for the durations of these events. Another objective of this project was to perform extensive simulation studies to investigate the impact of a population of Grid Friendly™ Appliances (GFAs) on the bulk power system frequency stability. The GFAs considered in this report are represented as demonstration units with water heaters individually modeled.

  3. Thermostat Controlled Loads Flexibility Assessment for Enabling Load Shifting – An Experimental Proof in a Low Voltage Grid

    DEFF Research Database (Denmark)

    Lakshmanan, Venkatachalam; Marinelli, Mattia; Kosek, Anna M.

    2017-01-01

    This paper investigates the usability of thermostat controlled domestic appliances for load shift in LV distribution grids. The proposed method uses refrigerators for the demonstration of adaptive load prediction to estimate its flexibility and perform scheduling based on load threshold limit. Tw...

  4. Three friendly walkers

    Science.gov (United States)

    Jensen, Iwan

    2017-01-01

    More than 15 years ago Guttmann and Vöge (2002 J. Stat. Plan. Inference 101 107), introduced a model of friendly walkers. Since then it has remained unsolved. In this paper we provide the exact solution to a closely allied model which essentially only differs in the boundary conditions. The exact solution is expressed in terms of the reciprocal of the generating function for vicious walkers which is a D-finite function. However, ratios of D-finite functions are inherently not D-finite and in this case we prove that the friendly walkers generating function is the solution to a non-linear differential equation with polynomial coefficients, it is in other words D-algebraic. We find using numerically exact calculations a conjectured expression for the generating function of the original model as a ratio of a D-finite function and the generating function for vicious walkers. We obtain an expression for this D-finite function in terms of a {{}2}{{F}1} hypergeometric function with a rational pullback and its first and second derivatives. Dedicated to Tony Guttmann on the occasion of his 70th birthday.

  5. Network-Friendly Gossiping

    Science.gov (United States)

    Serbu, Sabina; Rivière, Étienne; Felber, Pascal

    The emergence of large-scale distributed applications based on many-to-many communication models, e.g., broadcast and decentralized group communication, has an important impact on the underlying layers, notably the Internet routing infrastructure. To make an effective use of network resources, protocols should both limit the stress (amount of messages) on each infrastructure entity like routers and links, and balance as much as possible the load in the network. Most protocols use application-level metrics such as delays to improve efficiency of content dissemination or routing, but the extend to which such application-centric optimizations help reduce and balance the load imposed to the infrastructure is unclear. In this paper, we elaborate on the design of such network-friendly protocols and associated metrics. More specifically, we investigate random-based gossip dissemination. We propose and evaluate different ways of making this representative protocol network-friendly while keeping its desirable properties (robustness and low delays). Simulations of the proposed methods using synthetic and real network topologies convey and compare their abilities to reduce and balance the load while keeping good performance.

  6. Controllable Load Management Approaches in Smart Grids

    Directory of Open Access Journals (Sweden)

    Jingshuang Shen

    2015-10-01

    Full Text Available With rapid smart grid technology development, the customer can actively participate in demand-side management (DSM with the mutual information communication between the distributor operation company and the smart devices in real-time. Controllable load management not only has the advantage of peak shaving, load balance, frequency regulation, and voltage stability, but is also effective at providing fast balancing services to the renewable energy grid in the distributed power system. The load management faces an enormous challenge as the customer has a large number of both small residential loads and dispersed renewable sources. In this paper, various controllable load management approaches are discussed. The traditional controllable load approaches such as the end users’ controllable appliances, storage battery, Vehicle-to-Grid (V2G, and heat storage are reviewed. The “broad controllable loads” management, such as the microgrid, Virtual Power Plant (VPP, and the load aggregator are also presented. Furthermore, the load characteristics, control strategies, and control effectiveness are analyzed.

  7. The Anatomy of a Grid portal

    International Nuclear Information System (INIS)

    Licari, Daniele; Calzolari, Federico

    2011-01-01

    In this paper we introduce a new way to deal with Grid portals referring to our implementation. L-GRID is a light portal to access the EGEE/EGI Grid infrastructure via Web, allowing users to submit their jobs from a common Web browser in a few minutes, without any knowledge about the Grid infrastructure. It provides the control over the complete lifecycle of a Grid Job, from its submission and status monitoring, to the output retrieval. The system, implemented as client-server architecture, is based on the Globus Grid middleware. The client side application is based on a java applet; the server relies on a Globus User Interface. There is no need of user registration on the server side, and the user needs only his own X.509 personal certificate. The system is user-friendly, secure (it uses SSL protocol, mechanism for dynamic delegation and identity creation in public key infrastructures), highly customizable, open source, and easy to install. The X.509 personal certificate does not get out from the local machine. It allows to reduce the time spent for the job submission, granting at the same time a higher efficiency and a better security level in proxy delegation and management.

  8. The Anatomy of a Grid portal

    Science.gov (United States)

    Licari, Daniele; Calzolari, Federico

    2011-12-01

    In this paper we introduce a new way to deal with Grid portals referring to our implementation. L-GRID is a light portal to access the EGEE/EGI Grid infrastructure via Web, allowing users to submit their jobs from a common Web browser in a few minutes, without any knowledge about the Grid infrastructure. It provides the control over the complete lifecycle of a Grid Job, from its submission and status monitoring, to the output retrieval. The system, implemented as client-server architecture, is based on the Globus Grid middleware. The client side application is based on a java applet; the server relies on a Globus User Interface. There is no need of user registration on the server side, and the user needs only his own X.509 personal certificate. The system is user-friendly, secure (it uses SSL protocol, mechanism for dynamic delegation and identity creation in public key infrastructures), highly customizable, open source, and easy to install. The X.509 personal certificate does not get out from the local machine. It allows to reduce the time spent for the job submission, granting at the same time a higher efficiency and a better security level in proxy delegation and management.

  9. Parallel grid population

    Science.gov (United States)

    Wald, Ingo; Ize, Santiago

    2015-07-28

    Parallel population of a grid with a plurality of objects using a plurality of processors. One example embodiment is a method for parallel population of a grid with a plurality of objects using a plurality of processors. The method includes a first act of dividing a grid into n distinct grid portions, where n is the number of processors available for populating the grid. The method also includes acts of dividing a plurality of objects into n distinct sets of objects, assigning a distinct set of objects to each processor such that each processor determines by which distinct grid portion(s) each object in its distinct set of objects is at least partially bounded, and assigning a distinct grid portion to each processor such that each processor populates its distinct grid portion with any objects that were previously determined to be at least partially bounded by its distinct grid portion.

  10. Enabling Graph Appliance for Genome Assembly

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Rina [ORNL; Graves, Jeffrey A [ORNL; Lee, Sangkeun (Matt) [ORNL; Sukumar, Sreenivas R [ORNL; Shankar, Mallikarjun [ORNL

    2015-01-01

    In recent years, there has been a huge growth in the amount of genomic data available as reads generated from various genome sequencers. The number of reads generated can be huge, ranging from hundreds to billions of nucleotide, each varying in size. Assembling such large amounts of data is one of the challenging computational problems for both biomedical and data scientists. Most of the genome assemblers developed have used de Bruijn graph techniques. A de Bruijn graph represents a collection of read sequences by billions of vertices and edges, which require large amounts of memory and computational power to store and process. This is the major drawback to de Bruijn graph assembly. Massively parallel, multi-threaded, shared memory systems can be leveraged to overcome some of these issues. The objective of our research is to investigate the feasibility and scalability issues of de Bruijn graph assembly on Cray s Urika-GD system; Urika-GD is a high performance graph appliance with a large shared memory and massively multithreaded custom processor designed for executing SPARQL queries over large-scale RDF data sets. However, to the best of our knowledge, there is no research on representing a de Bruijn graph as an RDF graph or finding Eulerian paths in RDF graphs using SPARQL for potential genome discovery. In this paper, we address the issues involved in representing a de Bruin graphs as RDF graphs and propose an iterative querying approach for finding Eulerian paths in large RDF graphs. We evaluate the performance of our implementation on real world ebola genome datasets and illustrate how genome assembly can be accomplished with Urika-GD using iterative SPARQL queries.

  11. Smart grid security

    CERN Document Server

    Goel, Sanjay; Papakonstantinou, Vagelis; Kloza, Dariusz

    2015-01-01

    This book on smart grid security is meant for a broad audience from managers to technical experts. It highlights security challenges that are faced in the smart grid as we widely deploy it across the landscape. It starts with a brief overview of the smart grid and then discusses some of the reported attacks on the grid. It covers network threats, cyber physical threats, smart metering threats, as well as privacy issues in the smart grid. Along with the threats the book discusses the means to improve smart grid security and the standards that are emerging in the field. The second part of the b

  12. Class II malocclusion treatment using combined Twin Block and fixed orthodontic appliances – A case report

    Science.gov (United States)

    Al-Anezi, Saud A.

    2010-01-01

    The effect of the Twin Block functional orthodontic appliances is mostly dento-alveolar with small skeletal effect. There are certain clinical indications where functional appliances can be used successfully in class II malocclusion e.g. in a growing patient. The use of these appliances is greatly dependent on the patient’s compliance and they simplify the fixed appliance phase. In this case, a 13-year old adolescent was treated with Twin Block appliance followed by fixed appliance to detail the occlusion. The design and treatment effects were demonstrated in this case report. PMID:24151413

  13. Electrical appliance energy consumption control methods and electrical energy consumption systems

    Science.gov (United States)

    Donnelly, Matthew K [Kennewick, WA; Chassin, David P [Pasco, WA; Dagle, Jeffery E [Richland, WA; Kintner-Meyer, Michael [Richland, WA; Winiarski, David W [Kennewick, WA; Pratt, Robert G [Kennewick, WA; Boberly-Bartis, Anne Marie [Alexandria, VA

    2006-03-07

    Electrical appliance energy consumption control methods and electrical energy consumption systems are described. In one aspect, an electrical appliance energy consumption control method includes providing an electrical appliance coupled with a power distribution system, receiving electrical energy within the appliance from the power distribution system, consuming the received electrical energy using a plurality of loads of the appliance, monitoring electrical energy of the power distribution system, and adjusting an amount of consumption of the received electrical energy via one of the loads of the appliance from an initial level of consumption to an other level of consumption different than the initial level of consumption responsive to the monitoring.

  14. Electrical appliance energy consumption control methods and electrical energy consumption systems

    Science.gov (United States)

    Donnelly, Matthew K [Kennewick, WA; Chassin, David P [Pasco, WA; Dagle, Jeffery E [Richland, WA; Kintner-Meyer, Michael [Richland, WA; Winiarski, David W [Kennewick, WA; Pratt, Robert G [Kennewick, WA; Boberly-Bartis, Anne Marie [Alexandria, VA

    2008-09-02

    Electrical appliance energy consumption control methods and electrical energy consumption systems are described. In one aspect, an electrical appliance energy consumption control method includes providing an electrical appliance coupled with a power distribution system, receiving electrical energy within the appliance from the power distribution system, consuming the received electrical energy using a plurality of loads of the appliance, monitoring electrical energy of the power distribution system, and adjusting an amount of consumption of the received electrical energy via one of the loads of the appliance from an initial level of consumption to an other level of consumption different than the initial level of consumption responsive to the monitoring.

  15. New horizons in orthodontics & dentofacial orthopedics: fixed Twin Blocks & TransForce lingual appliances.

    Science.gov (United States)

    Clark, William John

    2011-01-01

    During the 20th century functional appliances evolved from night time wear to more flexible appliances for increased day time wear to full time wear with Twin Block appliances. The current trend is towards fixed functional appliances and this paper introduces the Fixed Twin Block, bonded to the teeth to eliminate problems of compliance in functional therapy. TransForce lingual appliances are pre-activated and may be used in first phase treatment for sagittal and transverse arch development. Alternatively they may be integrated with fixed appliances at any stage of treatment.

  16. Energy efficient appliance choice under the EU labeling scheme

    Energy Technology Data Exchange (ETDEWEB)

    Mills, Bradford F.; Schleich, Joachim [Fraunhofer-Institut fuer System- und Innovationsforschung (ISI), Karlsruhe (Germany)

    2010-02-15

    This paper extends the existing empirical literature on consumers' choices when exposed to energy labeling schemes by allowing choices to depend on household socio-economic characteristics, technology-related factors, behavioral and motivational factors, and country conditions in a multi-country analysis. To account for a possible knowledge-based selection bias, the econometric model distinguishes label class knowledge from the energy class choice decision. As a general finding, most covariates show stronger relationships with knowledge of labeling class than with the choice of energy efficiency class. Four factors show particularly strong and expected influences on label class awareness. First, general awareness of household energy use and energy saving technologies spills over into awareness of the energy class of specific appliances. Second, socioeconomic characteristics mater, as education increases label class awareness and older age reduces awareness. Third, economic incentives matter, as stated economic importance of energy saving and higher country electricity prices both generate greater label awareness. By contrast, stated concerns about global warming do not appear to have a broad impact on awareness. Fourth, effective country implementation of the labeling scheme raises label awareness. More surprisingly, most factors that promote awareness of appliance energy classes have a limited influence on actual appliance energy class choice. Efficient energy behavior in the household is not strongly linked to appliance energy class choice. Socio-economic characteristics also have limited influence. This finding is inline with other studies that find that household socio-economic characteristics have relatively weak associations with the adoption of energy efficient technologies (Mills and Schleich 2010, Brohmann et al. 2009). In fact, with education it is vocational degrees rather than university degrees that are positively associated with the propensity to

  17. Speech and orthodontic appliances: a systematic literature review.

    Science.gov (United States)

    Chen, Junyu; Wan, Jia; You, Lun

    2018-01-23

    Various types of orthodontic appliances can lead to speech difficulties. However, speech difficulties caused by orthodontic appliances have not been sufficiently investigated by an evidence-based method. The aim of this study is to outline the scientific evidence and mechanism of the speech difficulties caused by orthodontic appliances. Randomized-controlled clinical trials (RCT), controlled clinical trials, and cohort studies focusing on the effect of orthodontic appliances on speech were included. A systematic search was conducted by an electronic search in PubMed, EMBASE, and the Cochrane Library databases, complemented by a manual search. The types of orthodontic appliances, the affected sounds, and duration period of the speech disturbances were extracted. The ROBINS-I tool was applied to evaluate the quality of non-randomized studies, and the bias of RCT was assessed based on the Cochrane Handbook for Systematic Reviews of Interventions. No meta-analyses could be performed due to the heterogeneity in the study designs and treatment modalities. Among 448 screened articles, 13 studies were included (n = 297 patients). Different types of orthodontic appliances such as fixed appliances, orthodontic retainers and palatal expanders could influence the clarity of speech. The /i/, /a/, and /e/ vowels as well as /s/, /z/, /l/, /t/, /d/, /r/, and /ʃ/ consonants could be distorted by appliances. Although most speech impairments could return to normal within weeks, speech distortion of the /s/ sound might last for more than 3 months. The low evidence level grading and heterogeneity were the two main limitations in this systematic review. Lingual fixed appliances, palatal expanders, and Hawley retainers have an evident influence on speech production. The /i/, /s/, /t/, and /d/ sounds are the primarily affected ones. The results of this systematic review should be interpreted with caution and more high-quality RCTs with larger sample sizes and longer follow-up periods are

  18. The International Database of Efficient Appliances (IDEA): A new tool to support appliance energy-efficiency deployment

    International Nuclear Information System (INIS)

    Gerke, Brian F.; McNeil, Michael A.; Tu, Thomas

    2017-01-01

    Highlights: •IDEA collects, organizes, and stores data on appliance features and efficiency. •Data can be gathered for any appliance type on any international market. •IDEA enables new approaches to efficiency deployment and monitoring. •Techniques are developed for cross-market comparison of energy-savings potential. •We find significant cost-effective energy-savings potential from efficiency for Indian and Chinese refrigerators. -- Abstract: Appliance energy-efficiency programs are a central component of many countries’ energy-policy portfolios. A major barrier to optimal implementation of these programs is lack of data to determine market baselines, assess the potential for cost-effective energy savings, and track markets over time to evaluate and verify program impacts. To address this gap, we have developed the International Database of Efficient Appliances (IDEA), a suite of software tools that automatically gathers data that is currently dispersed across various online sources and compiles it into a unified repository of information on efficiency, price, and features for a diversity of appliances and devices in markets around the world. In this article we describe the framework and functionality of IDEA, and we demonstrate its power as a resource for research and policy development related to appliance energy efficiency. Using IDEA data for refrigerators in China and India, we assess the potential for cost-effective energy savings within each market by computing robust indicators that can also be easily compared across different appliances and markets. We find that significant cost-effective savings are available on both markets. We discuss implications for the development of future energy-efficiency deployment programs.

  19. Caffeine: Friend or Foe?

    Science.gov (United States)

    Doepker, Candace; Lieberman, Harris R; Smith, Andrew Paul; Peck, Jennifer D; El-Sohemy, Ahmed; Welsh, Brian T

    2016-01-01

    The debate on the safety of and regulatory approaches for caffeine continues among various stakeholders and regulatory authorities. This decision-making process comes with significant challenges, particularly when considering the complexities of the available scientific data, making the formulation of clear science-based regulatory guidance more difficult. To allow for discussions of a number of key issues, the North American Branch of the International Life Sciences Institute (ILSI) convened a panel of subject matter experts for a caffeine-focused session entitled "Caffeine: Friend or Foe?," which was held during the 2015 ILSI Annual Meeting. The panelists' expertise covered topics ranging from the natural occurrence of caffeine in plants and interindividual metabolism of caffeine in humans to specific behavioral, reproductive, and cardiovascular effects related to caffeine consumption. Each presentation highlighted the potential risks, benefits, and challenges that inform whether caffeine exposure warrants concern. This paper aims to summarize the key topics discussed during the session.

  20. My Nepalese Friends

    Institute of Scientific and Technical Information of China (English)

    1996-01-01

    NEPAL and China are good neighbors. In the 1980s many Chinese technicians went to Nepal to help build roads and other projects. As an interpreter with a Chinese construction cooperative, I worked there from 1993 to 1994. During my stay in Nepal, I met many different Nepalese women who impressed me deeply. My landlady Sumiyala, was the first Nepalese woman to come into my life. She was over 40 years old, a healthy and good-humored housewife. Whenever Ⅰ had time, I liked to chat with her and gradually we became friends. I remember my landlady was busy in and out of her house all day long— cleaning, cooking and taking care of her grandchildren and her parents-in-laws.

  1. Thinking with friends

    DEFF Research Database (Denmark)

    Emmeche, Claus

    2017-01-01

    cognitive phenomenon, and bringing together observations and concepts from interdisciplinary studies of interpersonal relationships allows for a notion of relational attention to be developed. At least for some forms of friendships, the agents not merely attend to common interests; their perception...... is shared, mediated by the very relationship as an embodied activity of distributed cognition. An important example of this is collaboration in science and art, as when friends or colleagues work close together to solve problems or develop new forms of creative expression.......Can research in situated and embodied cognition inform the study of interpersonal relations like friendship? And conversely, can friendship studies from disciplinary and interdisciplinary perspectives inspire research in cognitive science? These are the guiding questions for this chapter. Compared...

  2. Supporting Members and Friends

    Science.gov (United States)

    2005-10-01

    Thank you! Over the past year, AGU has received 12,104 gifts, both large and small, from members and friends. The Union has also received corporate contributions, National Science Foundation grants, and support from the National Oceanographic Partnership Program and National Association of Geoscience Teachers. Together their generosity has benefited AGU non revenue producing programs that are critical to our science and the future health of the Union. The following list gratefully acknowledges annual gifts of $100 or more and cumulative giving of $5,000 or more. The 1919 Society ($100,000 or more) and Benefactors ($5,000-$99,999) recognize single major gifts and cumulative contributions. Three circles acknowledge annual giving: President's Circle ($1,000 or more), Leadership Circle ($200-$999), and Supporters Circle ($100-$199). Supporting Life Members, who contribute a one-time gift of $1,200 in addition to lifetime dues, are among our most loyal Supporters.

  3. Environmentally friendly road construction

    Directory of Open Access Journals (Sweden)

    A.I. Essawy

    2013-06-01

    Full Text Available Environmental pollution is a major problem in developing countries like Egypt. Reuse of waste polymers is considered an attractive solution for environmental white pollution and reducing of the costs of road pavement and maintenance. This research aims to prepare environmentally friendly hot mix asphalt (HMA for paving using some industrial wastes as polypropylene and polyester fibers. The solid materials in the mix include normal and highly porous aggregates. 5% and 10% of waste polymers by weight of the asphalt were used to prepare special binders. The samples were tested for their physical properties, chemical properties, aging, scanning electron microscopy (SEM and thermo-gravimetric analysis (TGA. The results revealed that the prepared HMA using 5% of waste polymer had high performance as compared to the ordinary one and the waste polymer could be used in road construction.

  4. Integrating renewables in distribution grids. Storage, regulation and the interaction of different stakeholders in future grids

    Energy Technology Data Exchange (ETDEWEB)

    Nykamp, S.

    2013-10-18

    In recent years, the transition of the power supply chain towards a sustainable system based on 'green' electricity generation out of renewable energy sources (RES-E) has become a main challenge for grid operators and further stakeholders in the power system. To enable the evaluation of new concepts for the integration of RES-E, first the feed-in characteristics of photovoltaic, wind and biomass generators located in a distribution grid area and based on numerous measured feed-in data are studied in this thesis. The achieved insights from the feed-in profiles can be used for the dimensioning of grid assets. Furthermore, the results are useful for the evaluation of congestion management or for the dimensioning of storage assets in distribution grids. The latter aspect is analyzed in detail such that suitable storage characteristics for an introduction in the grid are determined. An economic approach is presented to derive break-even points for storage assets as a substitute to conventional reinforcements. For a case study from a real world low voltage grid with reinforcement needs, these break-even points are determined and the main influencing parameters are evaluated. A further important question in this context concerns the role DSOs (distribution system operators) may play with the operation of decentralized storage assets since several stakeholders may be interested in using the flexibility provided by these assets. This unclear responsibility also applies to the steering of adjustable consumption devices such as electric heat pumps or electric cars. For decentralized storage assets as well as heat pump appliances, optimal operation modes based on the optimization objectives for a DSO and a trader are derived. It is shown based on real world data that choosing a 'copperplate' scenario is not only technically insufficient for a global balance of the consumption and generation. It may even be harmful for the society from a welfare economic

  5. Face and neck dermatitis from a stainless steel orthodontic appliance.

    Science.gov (United States)

    Ehrnrooth, Minna; Kerosuo, Heidi

    2009-11-01

    Although nickel is the most common cause of contact allergy, nickel-containing orthodontic appliances seldom cause adverse reactions that result in discontinuation of treatment. We report on an eruption of dermatitis in the face and neck of an adult female patient after placement of a rapid maxillary expansion appliance (RME). Because the patient suspected nickel allergy, her tolerance to the appliance material was tested intraorally before treatment by cementing bands on four teeth for a week. No visible adverse reactions were seen during the test. One week after cementation of the RME appliance, the patient reported strong itching of the face and a red rash. Clinical examination showed itchy papular erythema on the face and neck. No intraoral reactions or symptoms were present. The RME appliance was removed, and symptoms disappeared in 4 to 5 days. The patient was referred for a nickel patch test, which gave a strong positive result. Adverse patient reactions of potential allergic origin should be diagnosed carefully, and their possible impact on further treatment should be evaluated accordingly.

  6. An Iterative Load Disaggregation Approach Based on Appliance Consumption Pattern

    Directory of Open Access Journals (Sweden)

    Huijuan Wang

    2018-04-01

    Full Text Available Non-intrusive load monitoring (NILM, monitoring single-appliance consumption level by decomposing the aggregated energy consumption, is a novel and economic technology that is beneficial to energy utilities and energy demand management strategies development. Hardware costs of high-frequency sampling and algorithm’s computational complexity hampered NILM large-scale application. However, low sampling data shows poor performance in event detection when multiple appliances are simultaneously turned on. In this paper, we contribute an iterative disaggregation approach that is based on appliance consumption pattern (ILDACP. Our approach combined Fuzzy C-means clustering algorithm, which provide an initial appliance operating status, and sub-sequence searching Dynamic Time Warping, which retrieves single energy consumption based on the typical power consumption pattern. Results show that the proposed approach is effective to accurately disaggregate power consumption, and is suitable for the situation where different appliances are simultaneously operated. Also, the approach has lower computational complexity than Hidden Markov Model method and it is easy to implement in the household without installing special equipment.

  7. Status Checking System of Home Appliances using machine learning

    Directory of Open Access Journals (Sweden)

    Yoon Chi-Yurl

    2017-01-01

    Full Text Available This paper describes status checking system of home appliances based on machine learning, which can be applied to existing household appliances without networking function. Designed status checking system consists of sensor modules, a wireless communication module, cloud server, android application and a machine learning algorithm. The developed system applied to washing machine analyses and judges the four-kinds of appliance’s status such as staying, washing, rinsing and spin-drying. The measurements of sensor and transmission of sensing data are operated on an Arduino board and the data are transmitted to cloud server in real time. The collected data are parsed by an Android application and injected into the machine learning algorithm for learning the status of the appliances. The machine learning algorithm compares the stored learning data with collected real-time data from the appliances. Our results are expected to contribute as a base technology to design an automatic control system based on machine learning technology for household appliances in real-time.

  8. Electronic Control System Of Home Appliances Using Speech Command Words

    Directory of Open Access Journals (Sweden)

    Aye Min Soe

    2015-06-01

    Full Text Available Abstract The main idea of this paper is to develop a speech recognition system. By using this system smart home appliances are controlled by spoken words. The spoken words chosen for recognition are Fan On Fan Off Light On Light Off TV On and TV Off. The input of the system takes speech signals to control home appliances. The proposed system has two main parts speech recognition and smart home appliances electronic control system. Speech recognition is implemented in MATLAB environment. In this process it contains two main modules feature extraction and feature matching. Mel Frequency Cepstral Coefficients MFCC is used for feature extraction. Vector Quantization VQ approach using clustering algorithm is applied for feature matching. In electrical home appliances control system RF module is used to carry command signal from PC to microcontroller wirelessly. Microcontroller is connected to driver circuit for relay and motor. The input commands are recognized very well. The system is a good performance to control home appliances by spoken words.

  9. Multi-agent approach for power system in a smart grid protection context

    DEFF Research Database (Denmark)

    Abedini, Reza; Pinto, Tiago; Morais, Hugo

    2013-01-01

    electricity markets and in the other hand with increasing penetration of Distributed Generation (DG) because of environment issues and diminishing in fossil fuel reserves and its price growth, made microgrid more attractive. Micro grids are considers as partial of SmartGrid system to accommodate DGs as well......With increasing penetration of electricity application in society and the need of majority of appliance to electricity, high level of reliability becomes more essential; in one hand with deregulation of electricity market in production, transmission and distribution and emerge of competitive...... proposes a new approach for protection in a Microgrid environment as a part of SmartGrid: Multi-agent system to Protections Coordination (MAS-ProteC) which integrated in MASGriP (Multi-Agent Smart Grid Platform), providing protection services within network operation in SmartGrid in electricity market...

  10. Realizing potential savings of energy and emissions from efficient household appliances in India

    International Nuclear Information System (INIS)

    Parikh, Kirit S.; Parikh, Jyoti K.

    2016-01-01

    The paper projects households' stock of four major electricity consuming appliances till 2030 and explores policy options to accelerate adoption of more energy efficient appliances. India's rapid economic growth has enabled the growing middle class to buy household appliances in increasing numbers. The consequent rise in energy consumption and GHG emissions can be significantly reduced if consumers are motivated by awareness and options in the market to buy energy efficient appliances. India has introduced a star rating scheme for appliances, and even without incentives consumers purchase star-rated appliances. The stock of household appliances is projected using the data of a national sample survey of household consumption, observed sale of star-rated appliances and projected consumption distribution. Estimated savings in households' electricity consumption from just four appliances, ACs, refrigerators, TVs, and ceiling fans, for which data were available, range from 52 bKwh to 145 bkwh in 2030, reductions of 10–27%. The corresponding reduction in CO_2 emissions will be between 42 Mt and 116 Mt in 2030. With policies of finance and bulk procurement to reduce costs, emissions reduction can be 128 Mt in 2030, a reduction of 30%. - Highlights: • Estimates the stock of selected household appliances with 20 classes of rural and urban households in the years 2030 in India. • Assesses the economics of energy efficient appliances. • Estimates spread of selected energy efficient appliances. • Assesses savings in energy consumption and CO_2 emissions in four alternative scenarios. • Suggests policies to promote energy efficient appliances.

  11. Grid generation methods

    CERN Document Server

    Liseikin, Vladimir D

    2010-01-01

    This book is an introduction to structured and unstructured grid methods in scientific computing, addressing graduate students, scientists as well as practitioners. Basic local and integral grid quality measures are formulated and new approaches to mesh generation are reviewed. In addition to the content of the successful first edition, a more detailed and practice oriented description of monitor metrics in Beltrami and diffusion equations is given for generating adaptive numerical grids. Also, new techniques developed by the author are presented, in particular a technique based on the inverted form of Beltrami’s partial differential equations with respect to control metrics. This technique allows the generation of adaptive grids for a wide variety of computational physics problems, including grid clustering to given function values and gradients, grid alignment with given vector fields, and combinations thereof. Applications of geometric methods to the analysis of numerical grid behavior as well as grid ge...

  12. Structural analysis of an off-grid tiny house

    Science.gov (United States)

    Calluari, Karina Arias; Alonso-Marroquín, Fernando

    2017-06-01

    The off-grid technologies and tiny house movement have experimented an unprecedented growth in recent years. Putting both sides together, we are trying to achieve an economic and environmental friendly solution to the higher cost of residential properties. This solution is the construction of off-grid tiny houses. This article presents a design for a small modular off-grid house made by pine timber. A numerical analysis of the proposed tiny house was performed to ensure its structural stability. The results were compared with the suggested serviceability limit state criteria, which are contended in the Australia Guidelines Standards making this design reliable for construction.

  13. Reducing Electricity Demand Peaks by Scheduling Home Appliances Usage

    DEFF Research Database (Denmark)

    Rossello Busquet, Ana; Kardaras, Georgios; Iversen, Villy Bæk

    2011-01-01

    Nowadays there is a tendency to consume electricity during the same period of the day leading to demand peaks. Regular energy consumption habits lead to demand peaks at specific temporal intervals, because users consume power at the same time. In order to avoid demand peaks, users’ appliances...... should consume electricity in a more temporarily distributed way. A new methodology to schedule the usage of home appliances is proposed and analyzed in this paper. The main concept behind this approach is the aggregation of home appliances into priority classes and the definition of a maximum power...... consumption limit, which is not allowed to be exceeded during peak hours. The scenario simulated describes a modern household, where the electrical devices are classified in low and high priority groups. The high priority devices are always granted power in order to operate without temporal restrictions...

  14. Fixed-functional appliance treatment combined with growth hormone therapy.

    Science.gov (United States)

    Jung, Min-Ho

    2017-09-01

    The purpose of this study was to illustrate the effects of growth hormone (GH) therapy and fixed functional appliance treatment in a 13-year-old Class II malocclusion patient without GH deficiency. GH has been shown to effectively increase endochondral growth and induce a more prognathic skeletal pattern. Although a major concern in Class II retrognathic patients is chin deficiency, long-term studies have shown that the mandibular growth enhancement effects of functional appliances are clinically insignificant. This case report demonstrates that the mandible grew significantly during fixed functional appliance treatment combined with GH therapy, with stable results during 2 years 11 months of retention. More studies are needed to evaluate GH therapy as a supplement in Class II treatment. Copyright © 2017 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

  15. Assessment of Literature Related to Combustion Appliance Venting Systems

    Energy Technology Data Exchange (ETDEWEB)

    Rapp, V. H.; Less, B. D.; Singer, B. C.; Stratton, J. C.; Wray, C. P.

    2015-02-01

    In many residential building retrofit programs, air tightening to increase energy efficiency is often constrained by safety concerns with naturally vented combustion appliances. Tighter residential buildings more readily depressurize when exhaust equipment is operated, making combustion appliances more prone to backdraft or spill combustion exhaust into the living space. Several measures, such as installation guidelines, vent sizing codes, and combustion safety diagnostics, are in place with the intent to prevent backdrafting and combustion spillage, but the diagnostics conflict and the risk mitigation objective is inconsistent. This literature review summarizes the metrics and diagnostics used to assess combustion safety, documents their technical basis, and investigates their risk mitigations. It compiles information from the following: codes for combustion appliance venting and installation; standards and guidelines for combustion safety diagnostics; research evaluating combustion safety diagnostics; research investigating wind effects on building depressurization and venting; and software for simulating vent system performance.

  16. Chimera Grid Tools

    Science.gov (United States)

    Chan, William M.; Rogers, Stuart E.; Nash, Steven M.; Buning, Pieter G.; Meakin, Robert

    2005-01-01

    Chimera Grid Tools (CGT) is a software package for performing computational fluid dynamics (CFD) analysis utilizing the Chimera-overset-grid method. For modeling flows with viscosity about geometrically complex bodies in relative motion, the Chimera-overset-grid method is among the most computationally cost-effective methods for obtaining accurate aerodynamic results. CGT contains a large collection of tools for generating overset grids, preparing inputs for computer programs that solve equations of flow on the grids, and post-processing of flow-solution data. The tools in CGT include grid editing tools, surface-grid-generation tools, volume-grid-generation tools, utility scripts, configuration scripts, and tools for post-processing (including generation of animated images of flows and calculating forces and moments exerted on affected bodies). One of the tools, denoted OVERGRID, is a graphical user interface (GUI) that serves to visualize the grids and flow solutions and provides central access to many other tools. The GUI facilitates the generation of grids for a new flow-field configuration. Scripts that follow the grid generation process can then be constructed to mostly automate grid generation for similar configurations. CGT is designed for use in conjunction with a computer-aided-design program that provides the geometry description of the bodies, and a flow-solver program.

  17. Bayesian grid matching

    DEFF Research Database (Denmark)

    Hartelius, Karsten; Carstensen, Jens Michael

    2003-01-01

    A method for locating distorted grid structures in images is presented. The method is based on the theories of template matching and Bayesian image restoration. The grid is modeled as a deformable template. Prior knowledge of the grid is described through a Markov random field (MRF) model which r...

  18. Assessment of Literature Related to Combustion Appliance Venting Systems

    Energy Technology Data Exchange (ETDEWEB)

    Rapp, Vi H. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Singer, Brett C. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Stratton, Chris [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Wray, Craig P. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2012-06-01

    In many residential building retrofit programs, air tightening to increase energy efficiency is constrained by concerns about related impacts on the safety of naturally vented combustion appliances. Tighter housing units more readily depressurize when exhaust equipment is operated, making combustion appliances more prone to backdraft or spillage. Several test methods purportedly assess the potential for depressurization-induced backdrafting and spillage, but these tests are not robustly reliable and repeatable predictors of venting performance, in part because they do not fully capture weather effects on venting performance. The purpose of this literature review is to investigate combustion safety diagnostics in existing codes, standards, and guidelines related to combustion appliances. This review summarizes existing combustion safety test methods, evaluations of these test methods, and also discusses research related to wind effects and the simulation of vent system performance. Current codes and standards related to combustion appliance installation provide little information on assessing backdrafting or spillage potential. A substantial amount of research has been conducted to assess combustion appliance backdrafting and spillage test methods, but primarily focuses on comparing short-term (stress) induced tests and monitoring results. Monitoring, typically performed over one week, indicated that combinations of environmental and house operation characteristics most conducive to combustion spillage were rare. Research, to an extent, has assessed existing combustion safety diagnostics for house depressurization, but the objectives of the diagnostics, both stress and monitoring, are not clearly defined. More research is also needed to quantify the frequency of test “failure” occurrence throughout the building stock and assess the statistical effects of weather (especially wind) on house depressurization and in turn on combustion appliance venting

  19. Cyber Friendly Fire

    Energy Technology Data Exchange (ETDEWEB)

    Greitzer, Frank L.; Carroll, Thomas E.; Roberts, Adam D.

    2011-09-01

    Cyber friendly fire (FF) is a new concept that has been brought to the attention of Department of Defense (DoD) stakeholders through two workshops that were planned and conducted by the Air Force Research Laboratory (AFRL) and research conducted for AFRL by the Pacific Northwest National Laboratory. With this previous work in mind, we offer a definition of cyber FF as intentional offensive or defensive cyber/electronic actions intended to protect cyber systems against enemy forces or to attack enemy cyber systems, which unintentionally harms the mission effectiveness of friendly or neutral forces. Just as with combat friendly fire, a fundamental need in avoiding cyber FF is to maintain situation awareness (SA). We suggest that cyber SA concerns knowledge of a system's topology (connectedness and relationships of the nodes in a system), and critical knowledge elements such as the characteristics and vulnerabilities of the components that comprise the system (and that populate the nodes), the nature of the activities or work performed, and the available defensive (and offensive) countermeasures that may be applied to thwart network attacks. A training implication is to raise awareness and understanding of these critical knowledge units; an approach to decision aids and/or visualizations is to focus on supporting these critical knowledge units. To study cyber FF, we developed an unclassified security test range comprising a combination of virtual and physical devices that present a closed network for testing, simulation, and evaluation. This network offers services found on a production network without the associated costs of a real production network. Containing enough detail to appear realistic, this virtual and physical environment can be customized to represent different configurations. For our purposes, the test range was configured to appear as an Internet-connected Managed Service Provider (MSP) offering specialized web applications to the general public

  20. International comparison of product certification and verification methods for appliances

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Nan [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Romankiewicz, John [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Fridley, David [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Zheng, Nina [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2012-06-01

    Enforcement of appliance standards and consumer trust in appliance labeling are important foundations of growing a more energy efficient economy. Product certification and verification increase compliance rates which in turn increase both energy savings and consumer trust. This paper will serve two purposes: 1) to review international practices for product certification and verification as they relate to the enforcement of standards and labeling programs in the U.S., E.U., Australia, Japan, Canada, and China; and 2) to make recommendations for China to implement improved certification processes related to their mandatory standards and labeling program such as to increase compliance rates and energy savings potential.

  1. International Comparison of Product Certification and Verification Methods for Appliances

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Nan [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Romankiewicz, John [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Fridley, David [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Zheng, Nina [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2012-06-01

    Enforcement of appliance standards and consumer trust in appliance labeling are important foundations of growing a more energy efficient economy. Product certification and verification increase compliance rates which in turn increase both energy savings and consumer trust. This paper will serve two purposes: 1) to review international practices for product certification and verification as they relate to the enforcement of standards and labeling programs in the U.S., E.U., Australia, Japan, Canada, and China; and 2) to make recommendations for China to implement improved certification processes related to their mandatory standards and labeling program such as to increase compliance rates and energy savings potential.

  2. Orthodontic parotitis: a rare complication from an orthodontic appliance.

    Science.gov (United States)

    McCarthy, Eileen; Cobb, Alistair R M

    2012-12-01

    A case is presented of a 14-year-old female undergoing orthodontic fixed appliance treatment who presented with right facial swelling in the parotid region. An initial diagnosis of acute infective parotitis was made by her primary care clinician. However, after clinical examination and ultrasonographic imaging, a diagnosis of salivary stasis secondary to inflammatory occlusion of Stensen's ductal orifice was made. The ductal orifice had been traumatized by the adjacent orthodontic appliance. This has not been described before in the literature. The differential diagnosis of parotid enlargement in children is discussed.

  3. Management of anterior dental crossbite with removable appliances

    Directory of Open Access Journals (Sweden)

    Ayca Tuba Ulusoy

    2013-01-01

    Full Text Available This case report describes the treatment of an 8-year-old girl with anterior dental crossbite using a series of removable appliances to bring the teeth into a normal position. Clinical presentation and intervention: A removable acrylic appliance with a bite plate incorporating a screw was used to correct the anterior dental crossbite and align the incisors. The subsequent eruption of the maxillary left lateral incisor on the palatinal side was treated with a second acrylic plate incorporating a labiolingual spring. After an 8-month period, the anterior crossbite involving multiple incisors was corrected.

  4. Marketing animal-friendly products

    NARCIS (Netherlands)

    Riemsdijk, van Lenka; Ingenbleek, Paul T.M.; Trijp, van Hans C.M.; Veen, van der Gerrita

    2017-01-01

    This article presents a conceptual framework that aims to encourage consumer animal-friendly product choice by introducing positioning strategies for animal-friendly products. These strategies reinforce the animal welfare with different types of consumption values and can therefore reduce

  5. The Managerial Grid; Key Orientations for Achieving Production through People.

    Science.gov (United States)

    Blake, Robert R; Mouton, Jane S.

    The Managerial Grid arranges a concern for production on the horizontal axis and a concern for people on the vertical axis of a coordinate system: 1,1 shows minimum concern for production and people; 9,1 shows major production emphasis and minimum human considerations; 1,9 shows maximum concern for friendly working conditions and minimum…

  6. Advanced Environment Friendly Nanotechnologies

    Science.gov (United States)

    Figovsky, O.; Beilin, D.; Blank, N.

    The economic, security, military and environmental implications of molecular manufacturing are extreme. Unfortunately, conflicting definitions of nanotechnology and blurry distinctions between significantly different fields have complicated the effort to understand those differences and to develop sensible, effective policy for each. The risks of today's nanoscale technologies cannot be treated the same as the risks of longer-term molecular manufacturing. It is a mistake to put them together in one basket for policy consideration — each is important to address, but they offer different problems and will require far different solutions. As used today, the term nanotechnology usually refers to a broad collection of mostly disconnected fields. Essentially, anything sufficiently small and interesting can be called nanotechnology. Much of it is harmless. For the rest, much of the harm is of familiar and limited quality. Molecular manufacturing, by contrast, will bring unfamiliar risks and new classes of problems. The advanced environment friendly nanotechnologies elaborated by Israel Company Polymate Ltd. — International Research Center are illustrated.

  7. An Enhanced System Architecture for Optimized Demand Side Management in Smart Grid

    Directory of Open Access Journals (Sweden)

    Anzar Mahmood

    2016-04-01

    Full Text Available Demand Side Management (DSM through optimization of home energy consumption in the smart grid environment is now one of the well-known research areas. Appliance scheduling has been done through many different algorithms to reduce peak load and, consequently, the Peak to Average Ratio (PAR. This paper presents a Comprehensive Home Energy Management Architecture (CHEMA with integration of multiple appliance scheduling options and enhanced load categorization in a smart grid environment. The CHEMA model consists of six layers and has been modeled in Simulink with an embedded MATLAB code. A single Knapsack optimization technique is used for scheduling and four different cases of cost reduction are modeled at the second layer of CHEMA. Fault identification and electricity theft control have also been added in CHEMA. Furthermore, carbon footprint calculations have been incorporated in order to make the users aware of environmental concerns. Simulation results prove the effectiveness of the proposed model.

  8. Grid Architecture 2

    Energy Technology Data Exchange (ETDEWEB)

    Taft, Jeffrey D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2016-01-01

    The report describes work done on Grid Architecture under the auspices of the Department of Electricity Office of Electricity Delivery and Reliability in 2015. As described in the first Grid Architecture report, the primary purpose of this work is to provide stakeholder insight about grid issues so as to enable superior decision making on their part. Doing this requires the creation of various work products, including oft-times complex diagrams, analyses, and explanations. This report provides architectural insights into several important grid topics and also describes work done to advance the science of Grid Architecture as well.

  9. Three case reports demonstrating treatment of relatively complex orthodontic cases using a completely customised lingual appliance.

    Science.gov (United States)

    Buckley, John

    2016-01-01

    It is a commonly held misconception among Irish dentists that only minor malocclusions can be treated with lingual appliances. This article demonstrates the use of contemporary completely customised lingual orthodontic appliances to treat a diverse range of malocclusions, to a satisfactory level, and thereby may disabuse clinicians of the belief that only minor malocclusions can be treated with lingual appliances.

  10. 46 CFR 167.15-28 - Inspection of lifesaving appliances and arrangements.

    Science.gov (United States)

    2010-10-01

    ... SCHOOLS PUBLIC NAUTICAL SCHOOL SHIPS Inspections § 167.15-28 Inspection of lifesaving appliances and arrangements. The inspection of lifesaving appliances and arrangements must be in accordance with the... 46 Shipping 7 2010-10-01 2010-10-01 false Inspection of lifesaving appliances and arrangements...

  11. Drawing on international experience to reform the Belgian market for ostomy appliances.

    Science.gov (United States)

    Simoens, Steven; Van den Steen, Dirk; Vanleene, Veerle; De Maré, Luc; Moldenaers, Ingrid; Debruyne, Hans; Ramaekers, Dirk

    2007-02-01

    This article aims to review the regulatory framework governing the Belgian ostomy appliance market in the light of the experience of Denmark, France, the Netherlands and Ontario (Canada) with regulation of ostomy appliances. Information about the regulatory framework was derived from the international literature, analysis of legal texts and a survey completed by national experts. The comparative analysis revealed that these countries have adopted varying approaches towards regulating their domestic ostomy appliance market. Strategies to keep down prices include public procurement in Denmark, maximum prices in France and exclusion of expensive appliances from reimbursement in the Netherlands. To contain public expenditure on ostomy appliances, consumption patterns are monitored in the Netherlands, the quantity of reimbursed appliances is limited in Belgium and public reimbursement is restricted in Ontario. Ostomy appliances are generally distributed by community pharmacies and medical equipment shops. In countries that emphasise home care delivery such as Denmark, domiciliary distributors dominate the market to the detriment of community pharmacies which do not seem to be able to offer this service at a competitive price. An avenue for reforming the Belgian ostomy appliance market is proposed which valorizes the role of ostomy care nurses in guiding the choice of ostomy appliances. Furthermore, it is recommended that a competitive tendering process determines the price of ostomy appliances, that reimbursement for service provision by distributors is separated from reimbursement of appliances, and that patients receive a fixed grant from the third-party payer to buy ostomy appliances.

  12. 42 CFR 410.36 - Medical supplies, appliances, and devices: Scope.

    Science.gov (United States)

    2010-10-01

    ... 42 Public Health 2 2010-10-01 2010-10-01 false Medical supplies, appliances, and devices: Scope... Services § 410.36 Medical supplies, appliances, and devices: Scope. (a) Medicare Part B pays for the following medical supplies, appliances and devices: (1) Surgical dressings, and splints, casts, and other...

  13. 46 CFR 196.37-37 - Markings for lifesaving appliances, instructions to passengers, and stowage locations.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Markings for lifesaving appliances, instructions to..., etc. § 196.37-37 Markings for lifesaving appliances, instructions to passengers, and stowage locations. Lifesaving appliances, instructions to passengers, and stowage locations must be marked in accordance with...

  14. 38 CFR 17.153 - Training in the use of appliances.

    Science.gov (United States)

    2010-07-01

    ... appliances. 17.153 Section 17.153 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS AFFAIRS MEDICAL Prosthetic, Sensory, and Rehabilitative Aids § 17.153 Training in the use of appliances. Beneficiaries supplied prosthetic and similar appliances will be additionally entitled to fitting and training...

  15. 49 CFR 176.54 - Repairs involving welding, burning, and power-actuated tools and appliances.

    Science.gov (United States)

    2010-10-01

    ...-actuated tools and appliances. 176.54 Section 176.54 Transportation Other Regulations Relating to..., burning, and power-actuated tools and appliances. (a) Except as provided in paragraph (b) of this section, repairs or work involving welding or burning, or the use of power-actuated tools or appliances which may...

  16. 42 CFR 409.25 - Drugs, biologicals, supplies, appliances, and equipment.

    Science.gov (United States)

    2010-10-01

    ... 42 Public Health 2 2010-10-01 2010-10-01 false Drugs, biologicals, supplies, appliances, and... Drugs, biologicals, supplies, appliances, and equipment. (a) Drugs and biologicals. Except as specified... can obtain a continuing supply. (c) Supplies, appliances, and equipment. Except as specified in...

  17. 46 CFR 58.16-20 - Ventilation of compartments containing gas-consuming appliances.

    Science.gov (United States)

    2010-10-01

    ... appliances. 58.16-20 Section 58.16-20 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED... and Heating § 58.16-20 Ventilation of compartments containing gas-consuming appliances. (a) Compartments containing gas-consuming appliances which are located above the weather deck shall be fitted with...

  18. 46 CFR 133.40 - Evaluation, testing and approval of lifesaving appliances and arrangements.

    Science.gov (United States)

    2010-10-01

    ... appliances and arrangements. 133.40 Section 133.40 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY... lifesaving appliances and arrangements. (a) Each item of lifesaving equipment required by this part to be... OCMI for use on the OSV. (c) The Commandant (CG-521) may accept a novel lifesaving appliance or...

  19. 14 CFR 21.617 - Issue of letters of TSO design approval: import appliances.

    Science.gov (United States)

    2010-01-01

    ...: import appliances. 21.617 Section 21.617 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION... Order Authorizations § 21.617 Issue of letters of TSO design approval: import appliances. (a) A letter of TSO design approval may be issued for an appliance that is manufactured in a foreign country with...

  20. 46 CFR 78.47-45 - Markings for lifesaving appliances, instructions to passengers, and stowage locations.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false Markings for lifesaving appliances, instructions to...-45 Markings for lifesaving appliances, instructions to passengers, and stowage locations. Lifesaving appliances, instructions to passengers, and stowage locations must be marked in accordance with subchapter W...

  1. 33 CFR 150.507 - How must the operator service inflatable lifesaving appliances?

    Science.gov (United States)

    2010-07-01

    ... inflatable lifesaving appliances? 150.507 Section 150.507 Navigation and Navigable Waters COAST GUARD... Specialty Equipment Inflatable Lifesaving Appliances § 150.507 How must the operator service inflatable lifesaving appliances? (a) The operator must service each inflatable liferaft according to 46 CFR subpart 160...

  2. 46 CFR 97.37-42 - Markings for lifesaving appliances, instructions to passengers, and stowage locations.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Markings for lifesaving appliances, instructions to..., Etc. § 97.37-42 Markings for lifesaving appliances, instructions to passengers, and stowage locations. Lifesaving appliances, instructions to passengers, and stowage locations must be marked in accordance with...

  3. 21 CFR 888.3030 - Single/multiple component metallic bone fixation appliances and accessories.

    Science.gov (United States)

    2010-04-01

    ... appliances and accessories. 888.3030 Section 888.3030 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT....3030 Single/multiple component metallic bone fixation appliances and accessories. (a) Identification. Single/multiple component metallic bone fixation appliances and accessories are devices intended to be...

  4. 46 CFR 199.40 - Evaluation, testing and approval of lifesaving appliances and arrangements.

    Science.gov (United States)

    2010-10-01

    ... appliances and arrangements. 199.40 Section 199.40 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) LIFESAVING APPLIANCES AND ARRANGEMENTS LIFESAVING SYSTEMS FOR CERTAIN INSPECTED VESSELS General § 199.40 Evaluation, testing and approval of lifesaving appliances and arrangements. (a) Each item of...

  5. 14 CFR 183.63 - Continuing requirements: Products, parts or appliances.

    Science.gov (United States)

    2010-01-01

    ... appliances. 183.63 Section 183.63 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... Designation Authorization § 183.63 Continuing requirements: Products, parts or appliances. For any approval or certificate for a product, part or appliance issued under the authority of this subpart, or under the...

  6. 14 CFR 3.5 - Statements about products, parts, appliances and materials.

    Science.gov (United States)

    2010-01-01

    ..., appliances and materials. 3.5 Section 3.5 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION DEFINITIONS GENERAL REQUIREMENTS § 3.5 Statements about products, parts, appliances... product, part, appliance or material. (b) Prohibition against fraudulent and intentionally false...

  7. Increased BMI in children-an indicator for less compliance during orthodontic treatment with removable appliances.

    Science.gov (United States)

    von Bremen, Julia; Lorenz, Nathalie; Ludwig, Björn; Ruf, Sabine

    2018-02-19

    To assess whether or not childhood overweight is associated with lower levels of compliance during orthodontic therapy with removable appliances. Starting in 2011, all upper expansion plates and Sander II appliances were equipped with a Theramon® microsensor chip to assess appliance wear time objectively. According to their pre-treatment, BMI normal weight patients were matched to consecutively treated overweight or obese patients by gender, age, and appliance type. Cooperation was assessed with microelectronic wear time documentation over a period of at least 6 months. A total of 50 patients (25 overweight, 25 normal weight) with upper expansion plates and 64 patients (32 overweight, 32 normal weight) with Sander II appliances were analysed. Spearman Rho coefficients showed an indirect association between BMI and appliance wear time, indicating that the higher the BMI, the less the patients wore their appliances (P appliances (P appliance wear during orthodontic treatment with removable appliances. Additional factors which influenced cooperation during treatment with removable appliances were patient age and appliance type.

  8. Smart grid technologies in local electric grids

    Science.gov (United States)

    Lezhniuk, Petro D.; Pijarski, Paweł; Buslavets, Olga A.

    2017-08-01

    The research is devoted to the creation of favorable conditions for the integration of renewable sources of energy into electric grids, which were designed to be supplied from centralized generation at large electric power stations. Development of distributed generation in electric grids influences the conditions of their operation - conflict of interests arises. The possibility of optimal functioning of electric grids and renewable sources of energy, when complex criterion of the optimality is balance reliability of electric energy in local electric system and minimum losses of electric energy in it. Multilevel automated system for power flows control in electric grids by means of change of distributed generation of power is developed. Optimization of power flows is performed by local systems of automatic control of small hydropower stations and, if possible, solar power plants.

  9. Mapping of grid faults and grid codes

    DEFF Research Database (Denmark)

    Iov, Florin; Hansen, A.D.; Sørensen, P.

    loads of wind turbines. The goal is also to clarify and define possible new directions in the certification process of power plant wind turbines, namely wind turbines, which participate actively in the stabilisation of power systems. Practical experience shows that there is a need...... challenges for the design of both the electrical system and the mechanical structure of wind turbines. An overview over the frequency of grid faults and the grid connection requirements in different relevant countries is done in this report. The most relevant study cases for the quantification of the loads......The present report is a part of the research project "Grid fault and design basis for wind turbine" supported by Energinet.dk through the grant PSO F&U 6319. The objective of this project is to investigate into the consequences of the new grid connection requirements for the fatigue and extreme...

  10. Mapping of grid faults and grid codes

    DEFF Research Database (Denmark)

    Iov, F.; Hansen, Anca Daniela; Sørensen, Poul Ejnar

    loads of wind turbines. The goal is also to clarify and define possible new directions in the certification process of power plant wind turbines, namely wind turbines, which participate actively in the stabilisation of power systems. Practical experience shows that there is a need...... challenges for the design of both the electrical system and the mechanical structure of wind turbines. An overview over the frequency of grid faults and the grid connection requirements in different relevant countries is done in this report. The most relevant study cases for the quantification of the loads......The present report is a part of the research project ''Grid fault and designbasis for wind turbine'' supported by Energinet.dk through the grant PSO F&U 6319. The objective of this project is to investigate into the consequences of the new grid connection requirements for the fatigue and extreme...

  11. Measures for improving the adoption of higher efficiency appliances in Indonesian households: An analysis of lifetime use and decision-making in the purchase of electrical appliances

    International Nuclear Information System (INIS)

    Wijaya, Muhammad Ery; Tezuka, Tetsuo

    2013-01-01

    Highlights: ► We observe human psychosocial variables regarding purchase of electrical appliances. ► Two cities with different cultures are subject of this study – Bandung and Yogyakarta. ► Differences in the lifetime of appliances can be attributed to the cultural. ► Ads and store’s staff have the greatest impact on people’s choice of appliances. ► Adoption of higher-efficiency appliances could be implemented based on each culture. - Abstract: One approach to decreasing electricity consumption is to facilitate the replacement of older appliances with new, higher-efficiency. The objectives of this paper are to compare and analyse the replacement of appliances in two cities of Indonesia – Yogyakarta and Bandung – that are characterised by different cultural backgrounds, ethnicities, and decision-making processes in the household purchase of electrical appliances. A questionnaire survey method was employed to obtain information on behavioural economics and human psychosocial variables such as attitudes, beliefs and perceived benefits regarding the replacement and purchase of electrical appliances. The results show that refrigerators in Yogyakarta have a longer lifetime than in Bandung. However, in Bandung, air conditioners, electric fans, rice cookers, and water pumps have a longer lifetime than in Yogyakarta. These differences in the lifetime of appliances can be attributed to the cultural differences within the two cities that are reflected in the manner in which people use electrical appliances as well as to their lack of knowledge regarding appliance operation. An analysis of the factors influencing the purchase of appliances indicated that people in Yogyakarta show a greater awareness of the benefits of adopting higher-efficiency appliances than do persons in Bandung. The following suggestions could be implemented to improve the strategy of encouraging the adoption of higher-efficiency appliances: (1) in Yogyakarta, energy labelling could be

  12. Compatibility of fixed orthodontic appliances with MR environment

    Czech Academy of Sciences Publication Activity Database

    Starčuk jr., Zenon; Hubálková, H.; Starčuková, Jana; Linetskiy, I.; Bartušek, Karel; Krupa, P.

    2006-01-01

    Roč. 19, Suppl. 1 (2006), EPOS 726:1-7 E-ISSN 1352-8661 R&D Projects: GA MZd NR8110 Institutional research plan: CEZ:AV0Z20650511 Keywords : orthodontic appliance * magnetic resonance * compatibility * dentistry * artifact Subject RIV: FS - Medical Facilities ; Equipment Impact factor: 0.756, year: 2005 http://posters.webges.com/esmrmb/epos

  13. 46 CFR 199.176 - Markings on lifesaving appliances.

    Science.gov (United States)

    2010-10-01

    ... ARRANGEMENTS LIFESAVING SYSTEMS FOR CERTAIN INSPECTED VESSELS Requirements for All Vessels § 199.176 Markings on lifesaving appliances. (a) Lifeboats and rescue boats. Each lifeboat and rescue boat must be plainly marked as follows: (1) Each side of each lifeboat and rescue boat bow must be marked in block...

  14. Adverse reactions to orthodontic appliances in nickel-allergic patients.

    Science.gov (United States)

    Volkman, Kristen K; Inda, Michael J; Reichl, Peter G; Zacharisen, Michael C

    2007-01-01

    Nickel allergy (NA) is common and causes more cases of allergic contact dermatitis (ACD) than all other metals combined. Many orthodontic appliances (ODAs) contain nickel but their clinical relevance in nickel-allergic patients is unclear. We aimed to characterize the relationship between NA and ODAs because the medical literature investigating this is controversial. A survey concerning adverse reactions to ODAs in patients with NA was distributed to members of the Wisconsin Society of Orthodontics. Forty-three surveys were analyzed. The surveyed group was experienced, representing a mean of 21.2 years in practice and averaging 242 appliances placed per year per orthodontist. Most new patients with orthodontia were 10-18 years old. Most wires used were nickel-titanium alloy. Although 76% of orthodontists inquired about NA at initial evaluation, 37% still placed nickel-containing ODAs in known nickel-allergic patients. Fifty percent placed a single intraoral appliance, observing for reactions. Three orthodontists applied ODAs to the skin similar to patch testing. Only 8 patients with reactions to ODAs were described in detail, 6 were female patients and 6 were aged 13-14 years. Intraoral and extraoral reactions were mild; diffuse urticaria was reported in one patient. Treatment included removing the appliances or changing to nonnickel alternatives with favorable outcomes. These cases, which included >33,000 patients, suggest a prevalence of 0.03%. Adverse reactions to ODAs in patients with NA have been observed but are uncommon. Using suitable alternatives, patients usually can be accommodated.

  15. Scheduling home-appliances to optimize energy consumption

    DEFF Research Database (Denmark)

    Rossello Busquet, Ana

    In order to optimize the energy consumption, energy demand peaks should be avoided, and energy consumption should be smoothly distributed over time. This can be achieved by setting a maximum energy consumption per user’s household. In other words, the overall consumption of the user’s appliances...

  16. Low-power Appliance Recognition using Recurrent Neural Networks

    NARCIS (Netherlands)

    Rizky Pratama, Azkario; Simanjuntak, Frans Juanda; Lazovik, Aliaksandr; Aiello, Marco

    2018-01-01

    Indoor energy consumption can be understood by breaking overall power consumption down into individual components and appliance activations. The clas- sification of components of energy usage is known as load disaggregation or ap- pliance recognition. Most of the previous efforts address the

  17. Radioactive tracers in the assessment of cleaning of surgical appliances

    International Nuclear Information System (INIS)

    Mostafa, A.B.M.G.; Chackett, K.F.

    1975-01-01

    Radioactive tracers which may be used in the assessment of cleaning of surgical appliances are described. Five labelled compounds were used as soiling material and tested in the rather severe conditions that exist during cleaning cycles. Measurements of decontamination in two cases were considered reliable but in the other three some degree of decomposition of the soil occurred, which falsified the results. (author)

  18. Do soft drinks affect metal ions release from orthodontic appliances?

    Science.gov (United States)

    Mikulewicz, Marcin; Wołowiec, Paulina; Loster, Bartłomiej W; Chojnacka, Katarzyna

    2015-01-01

    The effect of orange juice and Coca Cola(®) on the release of metal ions from fixed orthodontic appliances. A continuous flow system designed for in vitro testing of orthodontic appliances was used. Orange juice/Coca Cola(®) was flowing through the system alternately with artificial saliva for 5.5 and 18.5h, respectively. The collected samples underwent a multielemental ICP-OES analysis in order to determine the metal ions release pattern in time. The total mass of ions released from the appliance into orange juice and Coca Cola(®) (respectively) during the experiment was calculated (μg): Ni (15.33; 37.75), Cr (3.604; 1.052), Fe (48.42; ≥ 156.1), Cu (57.87, 32.91), Mn (9.164; 41.16), Mo (9.999; 30.12), and Cd (0.5967; 2.173). It was found that orange juice did not intensify the release of metal ions from orthodontic appliances, whereas Coca Cola(®) caused increased release of Ni ions. Copyright © 2015 Elsevier GmbH. All rights reserved.

  19. The Next Generation of Appliances: Visions for Sustainability

    DEFF Research Database (Denmark)

    Nørgaard, Jørgen; Guldbrandsen, Tom

    1998-01-01

    to consume no more than 50 kWh per year, without using any risky synthetic gasses. Washing appliances will use no electricity for heating, which will bring annual electricity consumption below 50 kWh for a washing machine. For electronic equipment, the efficiency gain known from battery operated version...

  20. Interoperability for smart appliances in the IoT world

    NARCIS (Netherlands)

    Daniele, L.; Solanki, M.; Hartog, F. den; Roes, J.

    2016-01-01

    Household appliances are set to become highly intelligent, smart and networked devices in the near future. Systematically deployed on the Internet of Things (IoT), they would be able to form complete energy consuming, producing, and managing ecosystems. Smart systems are technically very

  1. The Acceptance of Domestic Ambient Intelligence Appliances by Prospective Users

    NARCIS (Netherlands)

    Ben Allouch, Soumaya; van Dijk, Johannes A.G.M.; Peters, O.; Tokuda, Hideyuki; Beigl, Michael; Friday, Adrian; Bernheim Brush, A.J.; Tobe, Yoshito

    2009-01-01

    Ambient intelligence (AmI) is a growing interdisciplinary area where the focus is shifted towards users instead of merely emphasizing the technological opportunities of AmI. Different methods are employed to understand the adoption of AmI appliances by users. However, these are often small-scale

  2. Bio-Inspired Cyber Security for Smart Grid Deployments

    Energy Technology Data Exchange (ETDEWEB)

    McKinnon, Archibald D.; Thompson, Seth R.; Doroshchuk, Ruslan A.; Fink, Glenn A.; Fulp, Errin W.

    2013-05-01

    mart grid technologies are transforming the electric power grid into a grid with bi-directional flows of both power and information. Operating millions of new smart meters and smart appliances will significantly impact electric distribution systems resulting in greater efficiency. However, the scale of the grid and the new types of information transmitted will potentially introduce several security risks that cannot be addressed by traditional, centralized security techniques. We propose a new bio-inspired cyber security approach. Social insects, such as ants and bees, have developed complex-adaptive systems that emerge from the collective application of simple, light-weight behaviors. The Digital Ants framework is a bio-inspired framework that uses mobile light-weight agents. Sensors within the framework use digital pheromones to communicate with each other and to alert each other of possible cyber security issues. All communication and coordination is both localized and decentralized thereby allowing the framework to scale across the large numbers of devices that will exist in the smart grid. Furthermore, the sensors are light-weight and therefore suitable for implementation on devices with limited computational resources. This paper will provide a brief overview of the Digital Ants framework and then present results from test bed-based demonstrations that show that Digital Ants can identify a cyber attack scenario against smart meter deployments.

  3. Smart grid security

    Energy Technology Data Exchange (ETDEWEB)

    Cuellar, Jorge (ed.) [Siemens AG, Muenchen (Germany). Corporate Technology

    2013-11-01

    The engineering, deployment and security of the future smart grid will be an enormous project requiring the consensus of many stakeholders with different views on the security and privacy requirements, not to mention methods and solutions. The fragmentation of research agendas and proposed approaches or solutions for securing the future smart grid becomes apparent observing the results from different projects, standards, committees, etc, in different countries. The different approaches and views of the papers in this collection also witness this fragmentation. This book contains the following papers: 1. IT Security Architecture Approaches for Smart Metering and Smart Grid. 2. Smart Grid Information Exchange - Securing the Smart Grid from the Ground. 3. A Tool Set for the Evaluation of Security and Reliability in Smart Grids. 4. A Holistic View of Security and Privacy Issues in Smart Grids. 5. Hardware Security for Device Authentication in the Smart Grid. 6. Maintaining Privacy in Data Rich Demand Response Applications. 7. Data Protection in a Cloud-Enabled Smart Grid. 8. Formal Analysis of a Privacy-Preserving Billing Protocol. 9. Privacy in Smart Metering Ecosystems. 10. Energy rate at home Leveraging ZigBee to Enable Smart Grid in Residential Environment.

  4. Analisa Eco-friendly Attitudes Dan Eco-friendly Behavior Terhadap Eco-friendly Intention Green Hotel Di Indonesia

    OpenAIRE

    Silvia, Lanny; Rudijanto, Diana Gabriela; Kristanti, Monika

    2017-01-01

    Kesadaran masyarakat akan lingkungan yang semakin meningkat membuat masyarakat gencar mencari hotel yang ramah lingkungan dibandingkan dengan hotel konvensional. Penelitian ini bertujuan untuk mengetahui perbedaan eco-friendly attitude, eco- friendly behavior, dan eco-friendly intention konsumen generasi x dan generasi y terhadap green hotel di Indonesia dan apakah eco-friendly attitudes dan eco-friendly behavior berpengaruh signifikan terhadap eco-friendly intention. Total responden dalam pe...

  5. Informatics Solutions for Prosumers connected to Smart Grids

    Directory of Open Access Journals (Sweden)

    Simona Vasilica OPREA

    2015-03-01

    Full Text Available This paper gives a brief overview about electricity consumption optimization based on consumption profiles of electricity prosumers that are connected to smart grids. The main object of this approach is identification of informatics solutions for electricity consumption optimization in order to decrease electricity bill. In this way, larger scale integration of renewable energy sources is allowed therefore entire society will gain benefits. This paper describes the main objectives of such informatics system and stages for its implementation. The system will analyze the specific profile and behavior of each electricity consumer or prosumer, automatically assist him to make right decisions and offer optimal advice for usage of controllable and non-controllable appliances. It will serve, based on big data transfer from electricity consumers or prosumers, as a powerful tool for grid operators that will be able to better plan their resources.

  6. Integrating decentralized electrically powered thermal supply systems into a Smart Grid

    OpenAIRE

    Hasselmann, Maike; Beier, Carsten

    2015-01-01

    The goal of the project “Smart Region Pellworm” is the establishment and operation of a smart grid with a hybrid energy storage system on the German island of Pellworm. One part of the project is the integration of power-to-heat appliances into the smart grid for demand side management purposes. This paper deals with the prerequisites and lessons learned from the integration of electric night storage heaters into Pellworm's energy management system. Special focus lies on the development of a ...

  7. Emergencies in Orthodontics. Part 2: Management of Removable Appliances, Functional Appliances and other Adjuncts to Orthodontic Treatment.

    Science.gov (United States)

    Dowsing, Paul; Murray, Alison; Sandler, Jonathan

    2015-04-01

    In the second of two papers, management of orthodontic emergencies involving appliances other than Fixed appliances will be detailed. Problems relating to removable appliances, as well as other orthodontic adjuncts, will be discussed. Unfortunately, orthodontic appliance breakage does occur, despite the clinicians giving clear and concise instructions to the patients and their parents at fitting. If general dental practitioners have a practical knowledge of how to diagnose problems and to provide appropriate advice or timely 'emergency' treatment, this will significantly reduce the inconvenience for all parties concerned. It should also ensure that treatment progresses in the most efficient and comfortable manner for their patients. In specific situations the early, accurate identification of the problem and instigation of its appropriate management can avoid more serious consequences. Clinical Relevance: Appropriate handling of an orthodontic 'emergency' by the dentist can, on many occasions, provide immediate relief to the patient. This will, in turn, allow treatment to continue in the right direction, thus allowing more efficient and effective use of valuable resources.

  8. Wingridder - an interactive grid generator for TOUGH2

    International Nuclear Information System (INIS)

    Pan, Lehua

    2003-01-01

    The TOUGH (Transport Of Unsaturated Groundwater and Heat) family of codes has great flexibility in handling the variety of grid information required to describe a complex subsurface system. However, designing and generating such a grid can be a tedious and error-prone process. This is especially true when the number of cells and connections is very large. As a user-friendly, efficient, and effective grid generating software, WinGridder has been developed for designing, generating, and visualizing (at various spatial scales) numerical grids used in reservoir simulations and groundwater modeling studies. It can save mesh files for TOUGH family codes. It can also output additional grid information for various purposes in either graphic format or plain text format. It has user-friendly graphical user interfaces, along with an easy-to-use interactive design and plot tools. Many important features, such as inclined faults and offset, layering structure, local refinements, and embedded engineering structures, can be represented in the grid

  9. LHC computing grid

    International Nuclear Information System (INIS)

    Novaes, Sergio

    2011-01-01

    Full text: We give an overview of the grid computing initiatives in the Americas. High-Energy Physics has played a very important role in the development of grid computing in the world and in Latin America it has not been different. Lately, the grid concept has expanded its reach across all branches of e-Science, and we have witnessed the birth of the first nationwide infrastructures and its use in the private sector. (author)

  10. High density grids

    Energy Technology Data Exchange (ETDEWEB)

    Cohen, Aina E.; Baxter, Elizabeth L.

    2018-01-16

    An X-ray data collection grid device is provided that includes a magnetic base that is compatible with robotic sample mounting systems used at synchrotron beamlines, a grid element fixedly attached to the magnetic base, where the grid element includes at least one sealable sample window disposed through a planar synchrotron-compatible material, where the planar synchrotron-compatible material includes at least one automated X-ray positioning and fluid handling robot fiducial mark.

  11. Elliptic Curve Cryptography-Based Authentication with Identity Protection for Smart Grids.

    Directory of Open Access Journals (Sweden)

    Liping Zhang

    Full Text Available In a smart grid, the power service provider enables the expected power generation amount to be measured according to current power consumption, thus stabilizing the power system. However, the data transmitted over smart grids are not protected, and then suffer from several types of security threats and attacks. Thus, a robust and efficient authentication protocol should be provided to strength the security of smart grid networks. As the Supervisory Control and Data Acquisition system provides the security protection between the control center and substations in most smart grid environments, we focus on how to secure the communications between the substations and smart appliances. Existing security approaches fail to address the performance-security balance. In this study, we suggest a mitigation authentication protocol based on Elliptic Curve Cryptography with privacy protection by using a tamper-resistant device at the smart appliance side to achieve a delicate balance between performance and security of smart grids. The proposed protocol provides some attractive features such as identity protection, mutual authentication and key agreement. Finally, we demonstrate the completeness of the proposed protocol using the Gong-Needham-Yahalom logic.

  12. Elliptic Curve Cryptography-Based Authentication with Identity Protection for Smart Grids.

    Science.gov (United States)

    Zhang, Liping; Tang, Shanyu; Luo, He

    2016-01-01

    In a smart grid, the power service provider enables the expected power generation amount to be measured according to current power consumption, thus stabilizing the power system. However, the data transmitted over smart grids are not protected, and then suffer from several types of security threats and attacks. Thus, a robust and efficient authentication protocol should be provided to strength the security of smart grid networks. As the Supervisory Control and Data Acquisition system provides the security protection between the control center and substations in most smart grid environments, we focus on how to secure the communications between the substations and smart appliances. Existing security approaches fail to address the performance-security balance. In this study, we suggest a mitigation authentication protocol based on Elliptic Curve Cryptography with privacy protection by using a tamper-resistant device at the smart appliance side to achieve a delicate balance between performance and security of smart grids. The proposed protocol provides some attractive features such as identity protection, mutual authentication and key agreement. Finally, we demonstrate the completeness of the proposed protocol using the Gong-Needham-Yahalom logic.

  13. Micro grids toward the smart grid

    International Nuclear Information System (INIS)

    Guerrero, J.

    2011-01-01

    Worldwide electrical grids are expecting to become smarter in the near future, with interest in Microgrids likely to grow. A microgrid can be defined as a part of the grid with elements of prime energy movers, power electronics converters, distributed energy storage systems and local loads, that can operate autonomously but also interacting with main grid. Thus, the ability of intelligent Microgrids to operate in island mode or connected to the grid will be a keypoint to cope with new functionalities and the integration of renewable energy resources. The functionalities expected for these small grids are: black start operation, frequency and voltage stability, active and reactive power flow control, active power filter capabilities, and storage energy management. In this presentation, a review of the main concepts related to flexible Microgrids will be introduced, with examples of real Microgrids. AC and DC Microgrids to integrate renewable and distributed energy resources will also be presented, as well as distributed energy storage systems, and standardization issues of these Microgrids. Finally, Microgrid hierarchical control will be analyzed looking at three different levels: i) a primary control based on the droop method, including an output impedance virtual loop; ii) a secondary control, which enables restoring any deviations produced by the primary control; and iii) a tertiary control to manage the power flow between the microgrid and the external electrical distribution system.

  14. Development of environmentally friendly universal controller. Data and materials; 1998 nendo kankyo taio universal controller no kaihatsu seika hokokusho. Shiryohen

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    Research and development was carried out for an 'environmentally friendly universal controller (UC)' which would be 'user-friendly and energy-saving' when used with electrical home appliances, and data and materials on them were compiled into this volume. It covers the specifications (Versions 0.6 and 0.51) of a newly developed two-way controller protocol, the specification (Version 0.1) of two-way remote control IrDA-C communication unit hardware, an infrared communication protocol IrDa Control, and the like. It also accommodates information collected through surveys of technological trends as reflected in technical literature, Internet home pages, catalogs, and the like, concerning the user-friendliness of electrical home appliances, remote control, domestic consumption of electric power, and the like. Also covered is the result of surveys of patents involving environmentally friendly UC related technologies, namely, Japanese patents (from applications made in 1979 through disclosures made in 1998) and U.S. patents (registrations made in 1982 and thereafter). Furthermore, it contains the result of surveys of actualities of domestic use conducted for the purpose of clarifying the effect of environmentally friendly UC introduction, how such UCs are being accepted by the public, and the conditions that should be satisfied for their popularization. (NEDO)

  15. Development of environmentally friendly universal controller. Data and materials; 1998 nendo kankyo taio universal controller no kaihatsu seika hokokusho. Shiryohen

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    Research and development was carried out for an 'environmentally friendly universal controller (UC)' which would be 'user-friendly and energy-saving' when used with electrical home appliances, and data and materials on them were compiled into this volume. It covers the specifications (Versions 0.6 and 0.51) of a newly developed two-way controller protocol, the specification (Version 0.1) of two-way remote control IrDA-C communication unit hardware, an infrared communication protocol IrDa Control, and the like. It also accommodates information collected through surveys of technological trends as reflected in technical literature, Internet home pages, catalogs, and the like, concerning the user-friendliness of electrical home appliances, remote control, domestic consumption of electric power, and the like. Also covered is the result of surveys of patents involving environmentally friendly UC related technologies, namely, Japanese patents (from applications made in 1979 through disclosures made in 1998) and U.S. patents (registrations made in 1982 and thereafter). Furthermore, it contains the result of surveys of actualities of domestic use conducted for the purpose of clarifying the effect of environmentally friendly UC introduction, how such UCs are being accepted by the public, and the conditions that should be satisfied for their popularization. (NEDO)

  16. Challenges facing production grids

    Energy Technology Data Exchange (ETDEWEB)

    Pordes, Ruth; /Fermilab

    2007-06-01

    Today's global communities of users expect quality of service from distributed Grid systems equivalent to that their local data centers. This must be coupled to ubiquitous access to the ensemble of processing and storage resources across multiple Grid infrastructures. We are still facing significant challenges in meeting these expectations, especially in the underlying security, a sustainable and successful economic model, and smoothing the boundaries between administrative and technical domains. Using the Open Science Grid as an example, I examine the status and challenges of Grids operating in production today.

  17. Fixed functional appliances with multibracket appliances have no skeletal effect on the mandible: A systematic review and meta-analysis.

    Science.gov (United States)

    Ishaq, Ramy Abdul Rahman; AlHammadi, Maged Sultan; Fayed, Mona M S; El-Ezz, Amr Abou; Mostafa, Yehya

    2016-05-01

    Our aim was to assess the skeletal mandibular changes (anteroposterior and vertical) in circumpubertal patients with fixed functional appliances installed on multibracket appliances compared with untreated patients. An open-ended electronic search of 4 databases (PubMed, Embase, Cochrane Library, and Web of Science) up to April 2014 was performed. Additional searches of relevant journals, reference lists of the retrieved articles, systematic reviews, and gray literature were performed. Specific inclusion and exclusion criteria were applied to identify relevant articles. Quality was evaluated using the Cochrane Collaboration risk of bias tool and the Newcastle-Ottawa scale for prospective controlled clinical trials. Meta-analyses were conducted with fixed and random effects models as appropriate. Statistical heterogeneity was also examined. Seven articles were included in the qualitative synthesis and 5 in the meta-analysis. The included randomized controlled trials were at high risk of bias, and the methodologic quality of the prospective controlled clinical trials was high. Based on assessment of the fixed functional appliance phase in isolation, no difference in mandibular anteroposterior positional changes (SNB angle) (standard mean difference, 0.11°; 95% CI, -0.28, 0.50) was found between the treated and control groups. The vertical dimension was not influenced by the fixed functional appliance treatment. There is little high-quality evidence concerning the relative influence of fixed functional appliances on skeletal and dentoalveolar changes. However, based on the limited evidence, it appears that they have little effect on the skeletal mandibular parameters. Copyright © 2016 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

  18. 38 CFR 17.122 - Payment or reimbursement of the expenses of repairs to prosthetic appliances and similar devices...

    Science.gov (United States)

    2010-07-01

    ... of the expenses of repairs to prosthetic appliances and similar devices furnished without prior... Payment or reimbursement of the expenses of repairs to prosthetic appliances and similar devices furnished without prior authorization. The expenses of repairs to prosthetic appliances, or similar appliances...

  19. Social perceptions of adults wearing orthodontic appliances: a cross-sectional study.

    Science.gov (United States)

    Jeremiah, H G; Bister, D; Newton, J T

    2011-10-01

    This study ascertained the influence of orthodontic appliances on subjective ratings for social competence (SC), intellectual ability (IA), psychological adjustment (PA), and attractiveness in young adult orthodontic patients. A cross-sectional analytical questionnaire study was conducted with 130 undergraduates from the UK. Each participant was asked to look at a single, randomly assigned colour photograph of a young adult female and then asked to make judgements concerning her personal characteristics. Five modified photographs of the same young adult female were used: (1) no appliance, (2) stainless steel fixed orthodontic appliance, (3) ceramic fixed orthodontic appliance, (4) gold fixed orthodontic appliance, and (5) clear colourless aligner. Likert scales with higher scores indicating more positive ratings were used. The results were analysed using chi-square test, one-way univariate analysis of variance, and post hoc Tukey-B and Kruskal-Wallis tests. The results showed that greater perceived IA was associated with the appearance of no appliance (mean values: 7.56) rather than steel (6.67) or ceramic appliances (6.65) but similar to the gold (7.35) and aligner (7.08) appliances. No significant differences between the different orthodontic appliance appearances were found for SC and PA. A trend existed where the no appliance image (resembling a lingual appliance) or clear aligner was considered more attractive than the visible buccal fixed appliances. In the absence of other information, the judgements an individual young adult makes concerning the personal characteristics of a young adult are influenced by dental appearance and orthodontic appliance design. This may influence orthodontic appliance choice.

  20. Privacy friendly aggregation of smart meter readings, even when meters crash

    NARCIS (Netherlands)

    Hoepman, J.H.

    2017-01-01

    A well studied privacy problem in the area of smart grids is the question of how to aggregate the sum of a set of smart meter readings in a privacy friendly manner, i.e., in such a way that individual meter readings are not revealed to the adversary. Much less well studied is how to deal with

  1. Domestic appliances energy optimization with model predictive control

    International Nuclear Information System (INIS)

    Rodrigues, E.M.G.; Godina, R.; Pouresmaeil, E.; Ferreira, J.R.; Catalão, J.P.S.

    2017-01-01

    Highlights: • An alternative power management control for home appliances that require thermal regulation is presented. • A Model Predictive Control scheme is assessed and its performance studied and compared to the thermostat. • Problem formulation is explored through tuning weights with the aim of reducing energetic consumption and cost. • A modulation scheme of a two-level Model Predictive Control signal as an interface block is presented. • The implementation costs in home appliances with thermal regulation requirements are reduced. - Abstract: A vital element in making a sustainable world is correctly managing the energy in the domestic sector. Thus, this sector evidently stands as a key one for to be addressed in terms of climate change goals. Increasingly, people are aware of electricity savings by turning off the equipment that is not been used, or connect electrical loads just outside the on-peak hours. However, these few efforts are not enough to reduce the global energy consumption, which is increasing. Much of the reduction was due to technological improvements, however with the advancing of the years new types of control arise. Domestic appliances with the purpose of heating and cooling rely on thermostatic regulation technique. The study in this paper is focused on the subject of an alternative power management control for home appliances that require thermal regulation. In this paper a Model Predictive Control scheme is assessed and its performance studied and compared to the thermostat with the aim of minimizing the cooling energy consumption through the minimization of the energy cost while satisfying the adequate temperature range for the human comfort. In addition, the Model Predictive Control problem formulation is explored through tuning weights with the aim of reducing energetic consumption and cost. For this purpose, the typical consumption of a 24 h period of a summer day was simulated a three-level tariff scheme was used. The new

  2. Prospects of Appliance-Level Load Monitoring in Off-the-Shelf Energy Monitors: A Technical Review

    Directory of Open Access Journals (Sweden)

    Anwar Ul Haq

    2018-01-01

    Full Text Available The smart grid initiative has encouraged utility companies worldwide to roll-out new and smarter versions of energy meters. Before an extensive roll-out, which is both labor-intensive and incurs high capital costs, consumers need to be incentivised to reap the long-term benefits of such smart meters. Off-the-shelf energy monitors (e-monitors can provide consumers with an insight into such potential benefits. As e-monitors are owned by the consumer, the consumer has greater control over the data, which significantly reduces the privacy and data confidentiality concerns. Because only limited online technical information is available about e-monitors, we evaluate several existing e-monitors using an online technical survey directly from the vendors. Besides automated e-monitoring, the use of different off-the-shelf e-monitors can also help to demonstrate state-of-the-art techniques such as non-intrusive load monitoring (NILM, data analytics, and the predictive maintenance of appliances. Our survey indicates a trend towards the incorporation of such state-of-the-art capabilities, particularly the appliance-level e-monitoring and load disaggregation. We have also discussed some essential requirements to implement load disaggregation in the next generation e-monitors. In future, these intelligent e-monitoring techniques will encourage effective consumer participation in the demand-side management (DSM programs.

  3. GridOrbit public display

    DEFF Research Database (Denmark)

    Ramos, Juan David Hincapie; Tabard, Aurélien; Bardram, Jakob

    2010-01-01

    We introduce GridOrbit, a public awareness display that visualizes the activity of a community grid used in a biology laboratory. This community grid executes bioin-formatics algorithms and relies on users to donate CPU cycles to the grid. The goal of GridOrbit is to create a shared awareness about...

  4. Security for grids

    Energy Technology Data Exchange (ETDEWEB)

    Humphrey, Marty; Thompson, Mary R.; Jackson, Keith R.

    2005-08-14

    Securing a Grid environment presents a distinctive set of challenges. This paper groups the activities that need to be secured into four categories: naming and authentication; secure communication; trust, policy, and authorization; and enforcement of access control. It examines the current state of the art in securing these processes and introduces new technologies that promise to meet the security requirements of Grids more completely.

  5. The LHCb Grid Simulation

    CERN Multimedia

    Baranov, Alexander

    2016-01-01

    The LHCb Grid access if based on the LHCbDirac system. It provides access to data and computational resources to researchers with different geographical locations. The Grid has a hierarchical topology with multiple sites distributed over the world. The sites differ from each other by their number of CPUs, amount of disk storage and connection bandwidth. These parameters are essential for the Grid work. Moreover, job scheduling and data distribution strategy have a great impact on the grid performance. However, it is hard to choose an appropriate algorithm and strategies as they need a lot of time to be tested on the real grid. In this study, we describe the LHCb Grid simulator. The simulator reproduces the LHCb Grid structure with its sites and their number of CPUs, amount of disk storage and bandwidth connection. We demonstrate how well the simulator reproduces the grid work, show its advantages and limitations. We show how well the simulator reproduces job scheduling and network anomalies, consider methods ...

  6. The play grid

    DEFF Research Database (Denmark)

    Fogh, Rune; Johansen, Asger

    2013-01-01

    In this paper we propose The Play Grid, a model for systemizing different play types. The approach is psychological by nature and the actual Play Grid is based, therefore, on two pairs of fundamental and widely acknowledged distinguishing characteristics of the ego, namely: extraversion vs. intro...

  7. Planning in Smart Grids

    NARCIS (Netherlands)

    Bosman, M.G.C.

    2012-01-01

    The electricity supply chain is changing, due to increasing awareness for sustainability and an improved energy efficiency. The traditional infrastructure where demand is supplied by centralized generation is subject to a transition towards a Smart Grid. In this Smart Grid, sustainable generation

  8. Gridded Species Distribution, Version 1: Global Amphibians Presence Grids

    Data.gov (United States)

    National Aeronautics and Space Administration — The Global Amphibians Presence Grids of the Gridded Species Distribution, Version 1 is a reclassified version of the original grids of amphibian species distribution...

  9. Grid generation methods

    CERN Document Server

    Liseikin, Vladimir D

    2017-01-01

    This new edition provides a description of current developments relating to grid methods, grid codes, and their applications to actual problems. Grid generation methods are indispensable for the numerical solution of differential equations. Adaptive grid-mapping techniques, in particular, are the main focus and represent a promising tool to deal with systems with singularities. This 3rd edition includes three new chapters on numerical implementations (10), control of grid properties (11), and applications to mechanical, fluid, and plasma related problems (13). Also the other chapters have been updated including new topics, such as curvatures of discrete surfaces (3). Concise descriptions of hybrid mesh generation, drag and sweeping methods, parallel algorithms for mesh generation have been included too. This new edition addresses a broad range of readers: students, researchers, and practitioners in applied mathematics, mechanics, engineering, physics and other areas of applications.

  10. The GRID seminar

    CERN Multimedia

    CERN. Geneva HR-RFA

    2006-01-01

    The Grid infrastructure is a key part of the computing environment for the simulation, processing and analysis of the data of the LHC experiments. These experiments depend on the availability of a worldwide Grid infrastructure in several aspects of their computing model. The Grid middleware will hide much of the complexity of this environment to the user, organizing all the resources in a coherent virtual computer center. The general description of the elements of the Grid, their interconnections and their use by the experiments will be exposed in this talk. The computational and storage capability of the Grid is attracting other research communities beyond the high energy physics. Examples of these applications will be also exposed during the presentation.

  11. Hoisting appliances and fuel handling equipment at nuclear facilities

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-12-31

    The guide is followed by the Finnish Centre for Radiation and Nuclear Safety (STUK) in regulating hoisting and handling equipment Class 3 at nuclear facilities. The guide is applied e.g. to the following equipment: reactor building overhead cranes, hoisting appliances at nuclear fuel storages, fuel handling machines, other hoisting appliances, which because of nuclear safety aspects are classified in Safety Class 3, and load-bearing devices connected with the above equipment, such as replaceable hoisting tools and auxiliary lifting devices. The regulating of hoisting and handling equipment comprises the following stages: handling of preliminary and final safety analysis reports, inspection of the construction plan, supervision of fabrication and construction inspection, and supervision of initial start-up and commissioning inspection. 36 refs. Translation. The original text is published under the same guide number. The guide is valid from 5 January 1987 and will be in force until further notice.

  12. CE APPROVAL IN ELECTRICAL HOUSEHOLD APPLIANCES AND A CASE STUDY

    Directory of Open Access Journals (Sweden)

    Nazmi EKREN

    2009-01-01

    Full Text Available Due to the reason for rapidly developing technology, increasing competition medium, and awareness of the consumers, nowadays, the exigency of production with good quality has gained more and more significance. Certification of the quality and safety of the products to the consumers is compulsory in terms of producers. There are some documents to certify safety of the products. One of them is CE certificate. In this paper, basic information about CE mark is given and CE standards and tests required for electrical household appliances are mentioned. As an application, one of an electrical household appliance, toaster grill is treated and examined. To obtain CE certificate for toaster grill, required tests are made according to EN60335-2-9 and CE certificate is obtained.

  13. Analysis appliance by gamma tomography with focused collimators

    International Nuclear Information System (INIS)

    Stoddart, H.F.

    1978-01-01

    This invention concerns nuclear medicine and specifically an image-forming appliance providing a very sensitive quantitative determination and the localization in space of the radioactivity of a body organ such as the brain of a patient to whom a substance labelled with radioactive isotopes has been administered. The characteristics of this appliance, which forms an image in a transversal scanning field by means of radioactive isotope radiations, includes several highly focused collimators, placed in line and focused inwards so that they form an arrangement that surrounds a given scanning field. Each collimator is mobile with respect to the adjacent collimator and a system moves the collimators so that the focus of each one uniformly samples at least a half of the total scanning field corresponding to a cross section. The number of detectors is an even one between two and twenty four, and the collimators are twelve in number [fr

  14. Designing, Building and Controlling of Home Appliances Unit Using PC

    Directory of Open Access Journals (Sweden)

    Saleh Ben Safar

    2017-12-01

    Full Text Available Smart home is a residential building that is usually new or modern equipped with necessary tools and wiring that enable its occupants to control a number of electrical devices and several household appliances through a suitable software. Recently, the development of home automation systems is accelerating rapidly as a result of the rapid intersection of modern technologies. Here we are talking about systems for home communication networks as well as entertainment, security, convenience, etc. These systems are controlled by sending signals through wires distributed throughout the house or Through wireless means to programmable keys or devices so that they understand these commands and deal with them as desired. In this paper, I will discuss how to design the circuit with appropriate components, build it in Printed Circuit Board and connect it to a personal computer by using programmable language in order to control all home appliances by just one click. 

  15. Hoisting appliances and fuel handling equipment at nuclear facilities

    International Nuclear Information System (INIS)

    1987-01-01

    The guide is followed by the Finnish Centre for Radiation and Nuclear Safety (STUK) in regulating hoisting and handling equipment Class 3 at nuclear facilities. The guide is applied e.g. to the following equipment: reactor building overhead cranes, hoisting appliances at nuclear fuel storages, fuel handling machines, other hoisting appliances, which because of nuclear safety aspects are classified in Safety Class 3, and load-bearing devices connected with the above equipment, such as replaceable hoisting tools and auxiliary lifting devices. The regulating of hoisting and handling equipment comprises the following stages: handling of preliminary and final safety analysis reports, inspection of the construction plan, supervision of fabrication and construction inspection, and supervision of initial start-up and commissioning inspection

  16. Orthodontic treatment with a series of removable appliances.

    Science.gov (United States)

    Chenin, David A; Trosien, Andrew H; Fong, Patricia F; Miller, Robert A; Lee, Rodney S

    2003-09-01

    In the United States, the demand for straight white teeth has never been more important to patients. Crowded, poorly aligned teeth are not esthetically pleasing and are difficult to keep clean. However, until recently, the process of straightening the teeth typically has involved appliances involving bands, brackets and wires that also can be difficult to clean. The desire for a cosmetic solution to misaligned teeth has led to an increase in the number of patients seeking veneers, crowns and other laboratory-fabricated cosmetic restorations. Some clinicians are not aware that there are other ways to align teeth without either significant enamel reduction or conspicuous fixed orthodontic appliances. An alternative method of treatment, involving a series of clear removable appliances, circumvents this shortcoming and enables tooth alignment while avoiding deterioration in the cosmetics of the smile during treatment. This article describes a method of treatment, Invisalign (Align Technology, Santa Clara, Calif.), that clinicians can use in conjunction with 3-D computer models to accomplish the esthetic and oral hygiene objectives during and after treatment. The authors present three case reports, all involving a chief concern of crowding. The first case involved treatment of both arches by interproximal reduction, alignment of teeth and leveling the curve of Spee. The second case involved treatment of both arches by proclination, expansion and minor interproximal reduction. The final case shows relief of lower-arch crowding via lower-incisor extraction. In addition to satisfying the patient's chief concern of desiring straight teeth, this method of treatment satisfies additional objectives of esthetic treatment and esthetic results with significant oral hygiene benefits. Clinicians can address a patient's chief concern effectively without requiring an inventory of appliances (such as bands, brackets, wires and instruments). Furthermore, the use of 3-D computer models

  17. Appliance of geochemical engineering in radioactive waste disposal

    International Nuclear Information System (INIS)

    Li Shuang; Zhang Chengjiang; Ni Shijun; Li Kuanliang

    2008-01-01

    The basic foundation of applying geochemical engineering to control environment, common engineering models of disposal radioactive waste and the functions of the engineering barriers are introduced in this paper. The authors take the geochemical engineering barrier materiel research of a radioactive waste repository as an example to explain the appliance of geochemical engineering in the disposal of radioactive waste. And the results show that it can enhance the security of the nuclear waste repository if we use geochemical engineering barrier. (authors)

  18. Evaluation of photo-activation appliances used in dentistry

    Directory of Open Access Journals (Sweden)

    Thales Ribeiro de Magalhães Filho

    2008-01-01

    Full Text Available Objective: Verify the Vickers microhardness promoted by three photo-activation appliances: one Halogen Light Ultralux (Dabi-Atlante, Ribeirão Preto, Brazil and two Light Emitting Diodes. One with a larger diode (Ultraled, Dabi-Atlante, Ribeirão Preto, Brazil and the other with seven smaller diodes (Ultraled xp, Dabi-Atlante, Ribeirão Preto, Brazil in composites with different matrixes. Methods: Three test specimens were made for each resinous materials using silicone molds measuring 4 X 8 X 30 mm. Polymerization was performedin three stages and on the two surfaces. After having been submitted to careful polishing with sequential abrasive papers and diamond paste, the Vickers microhardness of the test specimens was determined. Afterwards these values were submitted to statistical analysis by the ANOVA table and Student’s-t test. Results: The microhardness values obtained in the hybrid composite were as follows: 51.63 kg/mm2 +- 3.27; 52.22 kg/mm2 +- 3.3; 38.08 kg/mm2 +-0.31 and in the ormocer, 41.87 kg/mm2 +- 2.36; 41.5 kg/mm2 +- 1.2; 33.63 kg/mm2 +- 1.2, by the Ultralux (Dabi-Atlante, Ribeirão Preto, Brazil, Ultraled xp (Dabi-Atlante, Ribeirão Preto, Brazil and Ultraled (Dabi-Atlante, Ribeirão Preto, Brazil appliances, respectively. Conclusion: The Ultraled (Dabi-Atlante, Ribeirão Preto, Brazil and Ultraled xp (Dabi-Atlante, Ribeirão Preto, Brazil appliances promoted microhardness values that were similar between them and higher than the values produced by Ultraled (Dabi-Atlante, Ribeirão Preto, Brazil in the composites. It was verified that the intensity of the photo-activator appliances is directly related to the microhardness they produce in the composites.

  19. Evaluation of Musculoskeletal Disorders in Household Appliances Manufacturing Company

    Directory of Open Access Journals (Sweden)

    Aioob Ghanbary

    2015-12-01

    Full Text Available Work-related musculoskeletal disorders are the most prevalent work-related disorders and injuries and being the main cause of disability. This study was conducted to assessment of the prevalence of musculoskeletal disorders in worker company household appliances production. Posture analysis was evaluated by OWAS method and prevalence of musculoskeletal disorders by Nordic questionnaire. With evaluating musculoskeletal disorders among company household appliances production can intervention action to reduce musculoskeletal disorders was carried out. This cross-sectional study was performed on 100 workers of the appliance manufacturing industry. These Individuals were included 15 persons from foam injection workshop, 17 persons from molding workshop, 17 operators of presses, 17 persons from packaging, 17 person from cutting unit and 17 operators of rivet. The Nordic questionnaire was completed by Individuals for the organs of arm, back, leg and wrist and Posture analysis was performed by OWAS method. The data were analyzed using Spss software version 18 and descriptive statistics and Anova test. Nordic questionnaire results revealed that highest disorders were observed in the arm (25%, back (22% and leg (21%. Also Anova test showed that was observed a significant correlation respectively between age and work experience with the prevalence of musculoskeletal disorders (p<0.02 (p<0.01. The results showed based on the level of risk OWAS for each job respectively, the highest level of risk associated with foam injection unit, packaging and cutting unit (risk level 4 and the lowest level of risk associated with molding workshop unit (risk level 2.The results of this study showed that household appliances Manufacturing workers due to the nature of their jobs are at risk of musculoskeletal disorders and Ergonomic interventions to do such as workstation redesign, reduced working hours, cycle of rest-work development.

  20. Acceptability and attractiveness of intra- and extra-oral orthodontic appliances.

    Science.gov (United States)

    Abu Alhaija, Elham S J; Karajeh, M A

    2013-01-01

    To evaluate the acceptability of different intra-oral and extra-oral orthodontic appliances, to rank orthodontic appliances from the most to the least attractive and to investigate the factors that may affect the acceptance of orthodontic treatment. A random sample of 800 students (schoolchildren and university students) were invited to participate in this study and a total of 688 students were included (86%). A self-administrated structured questionnaire was constructed for the purpose of this study. More than one-half in each age group (53%) claimed that they would accept to have orthodontic treatment. Acceptance of the different orthodontic appliances was affected by gender, age and type of school. Removable appliance was reported as the most acceptable and facemask was reported as the least acceptable orthodontic appliances. Majority of subjects ranked ceramic and facemask appliances as the most and the least attractive orthodontic appliances, respectively. The predictor variables for the acceptance of orthodontic treatment were perceived demand for orthodontic treatment, perceived positive effect of orthodontic treatment and expected benefits from orthodontic treatment. Removable appliance was the most acceptable orthodontic appliance whereas ceramic appliance was ranked as the most attractive one. Facemask was the least acceptable and the least attractive option.

  1. State of the Art Authentication, Access Control, and Secure Integration in Smart Grid

    Directory of Open Access Journals (Sweden)

    Neetesh Saxena

    2015-10-01

    Full Text Available The smart grid (SG is a promising platform for providing more reliable, efficient, and cost effective electricity to the consumers in a secure manner. Numerous initiatives across the globe are taken by both industry and academia in order to compile various security issues in the smart grid network. Unfortunately, there is no impactful survey paper available in the literature on authentications in the smart grid network. Therefore, this paper addresses the required objectives of an authentication protocol in the smart grid network along with the focus on mutual authentication, access control, and secure integration among different SG components. We review the existing authentication protocols, and analyze mutual authentication, privacy, trust, integrity, and confidentiality of communicating information in the smart grid network. We review authentications between the communicated entities in the smart grid, such as smart appliance, smart meter, energy provider, control center (CC, and home/building/neighborhood area network gateways (GW. We also review the existing authentication schemes for the vehicle-to-grid (V2G communication network along with various available secure integration and access control schemes. We also discuss the importance of the mutual authentication among SG entities while providing confidentiality and privacy preservation, seamless integration, and required access control with lower overhead, cost, and delay. This paper will help to provide a better understanding of current authentication, authorization, and secure integration issues in the smart grid network and directions to create interest among researchers to further explore these promising areas.

  2. Evaluation of safety management in an Appliances manufacturing company

    Directory of Open Access Journals (Sweden)

    F. Golbabaei

    2015-01-01

    Full Text Available Introduction: Prevention of accidents and work related diseases, are not allowed regardless of the safety of employees, customers, contractors and other persons. Assessment of individual safety management activities could reduce many losses. Present study aimed to evaluate the safety management of a household appliance manufacturing company.  .Material and Method: This study has done in a household appliance manufacturing company in Damavand city. Two questionnaires were firstly designed based on the weighted scores. The questionnaire 1 consisted of 4 indicators: Safety of machinery, Electrical safety, Risk assessment and Fire safety. Questionnaire 2 consisted of 11 sub indicators. Both questionnaires were completed by 30 HSE experts and supervisors. Reliability of questionnaires was based on cronbachs alpha coefficient. the safety status of each unit was determined and scored using information acquired by the questionnaires. Lastly, the safety of the entire company was determined.  .Result: Results showed that in safety management: the pressing and store house were in a good range of 66.66 and 60.12 points. Powder painting, enameling, laboratory were in a average range of 56.25, 55.92 and 54.15 points. Assembling and door storage were in a week range of 46.06 points.  .Conclusion: The findings showed that the safety status in the studied appliances company is in average range with 55.45 points. Therefore, it is recommended that the safety indicators should be improved for the betterment of the safety management in the company.

  3. Factors affecting dental biofilm in patients wearing fixed orthodontic appliances.

    Science.gov (United States)

    Mei, Li; Chieng, Joyce; Wong, Connie; Benic, Gareth; Farella, Mauro

    2017-12-01

    The aim of this study is to investigate the amount and the distribution of biofilm in patients wearing fixed appliances and its relation with age, gender, frequency of tooth brushing, and patient motivation. The sample comprised 52 patients (15.5 ± 3.6 years old, 30 females and 22 males) wearing fixed orthodontic appliances. Dental biofilm was assessed using a modified plaque index (PI). A questionnaire was used to collect patient's information, including gender, age, treatment motivation, and frequency of tooth brushing. Gingival (PI score = 0.9 ± 0.7), mesial (0.8 ± 0.6), and distal (0.8 ± 0.5) areas accumulated more biofilm than occlusal areas (0.3 ± 0.3) (P appliances have the highest biofilm accumulation on the maxillary lateral incisors and maxillary canines, particularly in the gingival area and areas behind arch wires. Less biofilm was observed in female and adult patients and in those who were self-motivated and brushed their teeth more often.

  4. Critical friends and collaborative partnership

    Directory of Open Access Journals (Sweden)

    Katarina Jandér

    2013-12-01

    Full Text Available Critical friends: a method for peer feedback The Critical Friend-method has been used in various educational settings to facilitate the process of continuous improvement in teaching. The aim of this study was to implement Critical Friends, and to find out if this method could be used for feedback on teaching as part of a librarians' professional development. The project was carried out within the Library Unit of the Faculty of Medicine at Lund University, Sweden, in collaboration with the faculty's Centre for Teaching and Learning. Seven librarians and an educational consultant from the Centre for Teaching and Learning participated; the educational consultant played an essential role in supervising and structuring the project and the evaluation process, preparing readings as well as being an active participant. The participants worked in pairs; the performance of one teacher and the associated classroom activities were observed by the critical friend, and then evaluated and discussed. Evaluation and results After two preparatory group meetings, a final meeting was held where all pairs reported what they had done and how they perceived the critical friend process. The experiences of the participating librarians were explored using a questionnaire. The questionnaire was analyzed using content analysis by one librarian and the educational consultant independently. The results suggested that use of the critical friend method could have a positive impact by achieving the following: strengthening shared values concerning teaching issues; promoting self-reflection on teaching; facilitating communication with colleagues; and reducing the sense of 'loneliness‘ in teaching. The difficulties in the implementation were lack of time and competing duties. It was perceived as an advantage to work in close partnership with the faculty's educational consultants, who were familiar with the organization.

  5. Improving energy efficiency and smart grid program analysis with agent-based end-use forecasting models

    International Nuclear Information System (INIS)

    Jackson, Jerry

    2010-01-01

    Electric utilities and regulators face difficult challenges evaluating new energy efficiency and smart grid programs prompted, in large part, by recent state and federal mandates and financial incentives. It is increasingly difficult to separate electricity use impacts of individual utility programs from the impacts of increasingly stringent appliance and building efficiency standards, increasing electricity prices, appliance manufacturer efficiency improvements, energy program interactions and other factors. This study reviews traditional approaches used to evaluate electric utility energy efficiency and smart-grid programs and presents an agent-based end-use modeling approach that resolves many of the shortcomings of traditional approaches. Data for a representative sample of utility customers in a Midwestern US utility are used to evaluate energy efficiency and smart grid program targets over a fifteen-year horizon. Model analysis indicates that a combination of the two least stringent efficiency and smart grid program scenarios provides peak hour reductions one-third greater than the most stringent smart grid program suggesting that reductions in peak demand requirements are more feasible when both efficiency and smart grid programs are considered together. Suggestions on transitioning from traditional end-use models to agent-based end-use models are provided.

  6. Decentral Smart Grid Control

    Science.gov (United States)

    Schäfer, Benjamin; Matthiae, Moritz; Timme, Marc; Witthaut, Dirk

    2015-01-01

    Stable operation of complex flow and transportation networks requires balanced supply and demand. For the operation of electric power grids—due to their increasing fraction of renewable energy sources—a pressing challenge is to fit the fluctuations in decentralized supply to the distributed and temporally varying demands. To achieve this goal, common smart grid concepts suggest to collect consumer demand data, centrally evaluate them given current supply and send price information back to customers for them to decide about usage. Besides restrictions regarding cyber security, privacy protection and large required investments, it remains unclear how such central smart grid options guarantee overall stability. Here we propose a Decentral Smart Grid Control, where the price is directly linked to the local grid frequency at each customer. The grid frequency provides all necessary information about the current power balance such that it is sufficient to match supply and demand without the need for a centralized IT infrastructure. We analyze the performance and the dynamical stability of the power grid with such a control system. Our results suggest that the proposed Decentral Smart Grid Control is feasible independent of effective measurement delays, if frequencies are averaged over sufficiently large time intervals.

  7. Decentral Smart Grid Control

    International Nuclear Information System (INIS)

    Schäfer, Benjamin; Matthiae, Moritz; Timme, Marc; Witthaut, Dirk

    2015-01-01

    Stable operation of complex flow and transportation networks requires balanced supply and demand. For the operation of electric power grids—due to their increasing fraction of renewable energy sources—a pressing challenge is to fit the fluctuations in decentralized supply to the distributed and temporally varying demands. To achieve this goal, common smart grid concepts suggest to collect consumer demand data, centrally evaluate them given current supply and send price information back to customers for them to decide about usage. Besides restrictions regarding cyber security, privacy protection and large required investments, it remains unclear how such central smart grid options guarantee overall stability. Here we propose a Decentral Smart Grid Control, where the price is directly linked to the local grid frequency at each customer. The grid frequency provides all necessary information about the current power balance such that it is sufficient to match supply and demand without the need for a centralized IT infrastructure. We analyze the performance and the dynamical stability of the power grid with such a control system. Our results suggest that the proposed Decentral Smart Grid Control is feasible independent of effective measurement delays, if frequencies are averaged over sufficiently large time intervals. (paper)

  8. The open science grid

    International Nuclear Information System (INIS)

    Pordes, R.

    2004-01-01

    The U.S. LHC Tier-1 and Tier-2 laboratories and universities are developing production Grids to support LHC applications running across a worldwide Grid computing system. Together with partners in computer science, physics grid projects and active experiments, we will build a common national production grid infrastructure which is open in its architecture, implementation and use. The Open Science Grid (OSG) model builds upon the successful approach of last year's joint Grid2003 project. The Grid3 shared infrastructure has for over eight months provided significant computational resources and throughput to a range of applications, including ATLAS and CMS data challenges, SDSS, LIGO, and biology analyses, and computer science demonstrators and experiments. To move towards LHC-scale data management, access and analysis capabilities, we must increase the scale, services, and sustainability of the current infrastructure by an order of magnitude or more. Thus, we must achieve a significant upgrade in its functionalities and technologies. The initial OSG partners will build upon a fully usable, sustainable and robust grid. Initial partners include the US LHC collaborations, DOE and NSF Laboratories and Universities and Trillium Grid projects. The approach is to federate with other application communities in the U.S. to build a shared infrastructure open to other sciences and capable of being modified and improved to respond to needs of other applications, including CDF, D0, BaBar, and RHIC experiments. We describe the application-driven, engineered services of the OSG, short term plans and status, and the roadmap for a consortium, its partnerships and national focus

  9. Reducing electricity demand peaks by scheduling home appliances usage

    Energy Technology Data Exchange (ETDEWEB)

    Rossello-Busquet, A.; Kardaras, G.; Baek Iversen, V.; Soler, J.; Dittmann, L.

    2011-05-15

    Nowadays there is a tendency to consume electricity during the same period of the day leading to demand peaks. Regular energy consumption habits lead to demand peaks at specific temporal intervals, because users consume power at the same time. In order to avoid demand peaks, users' appliances should consume electricity in a more temporarily distributed way. A new methodology to schedule the usage of home appliances is proposed and analyzed in this paper. The main concept behind this approach is the aggregation of home appliances into priority classes and the definition of a maximum power consumption limit, which is not allowed to be exceeded during peak hours. The scenario simulated describes a modern household, where the electrical devices are classified in low and high priority groups. The high priority devices are always granted power in order to operate without temporal restrictions. On the contrary, the low priority devices have to pause their operation, when the algorithm dictates it, and resume it in the future. This can become beneficial for both energy companies and users. The electricity suppliers companies will be capable of regulating power generation during demand peaks periods. Moreover, users can be granted lower electricity bill rates for accepting delaying the operation of some of their appliances. In order to analyze this scenario, teletraffic engineering theory, which is used in evaluating the performance of telecommunication networks, is used. A reversible fair scheduling (RFS) algorithm, which was originally developed for telecommunication networks, is applied. The purpose is to analyze how a power consumption limit and priorities for home appliances will affect the demand peak and the users' everyday life. Verification of the effectiveness of the RFS algorithm is done by means of simulation and by using real data for power consumption and operation hours. The defined maximum power limit of 750 and 1000 Watt was not exceeded during

  10. Desktop grid computing

    CERN Document Server

    Cerin, Christophe

    2012-01-01

    Desktop Grid Computing presents common techniques used in numerous models, algorithms, and tools developed during the last decade to implement desktop grid computing. These techniques enable the solution of many important sub-problems for middleware design, including scheduling, data management, security, load balancing, result certification, and fault tolerance. The book's first part covers the initial ideas and basic concepts of desktop grid computing. The second part explores challenging current and future problems. Each chapter presents the sub-problems, discusses theoretical and practical

  11. Transmission grid security

    CERN Document Server

    Haarla, Liisa; Hirvonen, Ritva; Labeau, Pierre-Etienne

    2011-01-01

    In response to the growing importance of power system security and reliability, ""Transmission Grid Security"" proposes a systematic and probabilistic approach for transmission grid security analysis. The analysis presented uses probabilistic safety assessment (PSA) and takes into account the power system dynamics after severe faults. In the method shown in this book the power system states (stable, not stable, system breakdown, etc.) are connected with the substation reliability model. In this way it is possible to: estimate the system-wide consequences of grid faults; identify a chain of eve

  12. Trends in life science grid: from computing grid to knowledge grid

    Directory of Open Access Journals (Sweden)

    Konagaya Akihiko

    2006-12-01

    Full Text Available Abstract Background Grid computing has great potential to become a standard cyberinfrastructure for life sciences which often require high-performance computing and large data handling which exceeds the computing capacity of a single institution. Results This survey reviews the latest grid technologies from the viewpoints of computing grid, data grid and knowledge grid. Computing grid technologies have been matured enough to solve high-throughput real-world life scientific problems. Data grid technologies are strong candidates for realizing "resourceome" for bioinformatics. Knowledge grids should be designed not only from sharing explicit knowledge on computers but also from community formulation for sharing tacit knowledge among a community. Conclusion Extending the concept of grid from computing grid to knowledge grid, it is possible to make use of a grid as not only sharable computing resources, but also as time and place in which people work together, create knowledge, and share knowledge and experiences in a community.

  13. Association of tooth brushing behavior with oral hygiene index among students using fixed appliance

    Science.gov (United States)

    Ria, N.; Eyanoer, P.

    2018-03-01

    Uses of fixed appliance have become popular recently. The purpose of its use is to correct malposition of teeth in order to normalize the masticatory function and to eliminate the accumulation of food remain between the teeth. These will prevent the formation of caries and any periodontal tissue disease. Fixed appliance patients must routinely maintain their oral hygiene. This study was an analytical survey with cross-sectional design to know the relationship between behavior in tooth brushing of students using thefixed appliance and oral hygiene in Poltekkes Kemenkes Medan. The average of Oral Hygiene Index – Simplified (OHI-S) value of students using fixed appliance (2.68) was still above national target which is ≤2, and there was a relationship between behavior in tooth brushing of students using the fixed appliance and oral hygiene (phygiene and to prevent caries formation and periodontal disease patients using fixed appliances should maintain their dental health.

  14. Evaluation of dentoskeletal effects of Farmand functional appliance (Fa II) on class II malocclusion

    OpenAIRE

    Yassaei S.; Aghili H.; Razeghi D.

    2007-01-01

    Background and Aim: Functional appliances refer to a variety of removable or fixed appliances designed to alter the mandibular position both sagitally and vertically, resulting in orthodontic and orthopedic changes. Despite the long history of functional appliances, there is still much controversy related to their effectiveness and mode of action. The aim of this study was to evaluate dental and skeletal effects of Fa II in patients with class II malocclusion due to mandibular deficiency.Mate...

  15. Climate-friendly Default Rules

    DEFF Research Database (Denmark)

    Sunstein, Cass R.; Reisch, Lucia A.

    . The underlying reasons include the power of suggestion; inertia and procrastination; and loss aversion. If well-chosen, climate-friendly defaults are likely to have large effects in reducing the economic and environmental harms associated with various products and activities. In deciding whether to establish...

  16. Lincoln Laboratory Grid

    Data.gov (United States)

    Federal Laboratory Consortium — The Lincoln Laboratory Grid (LLGrid) is an interactive, on-demand parallel computing system that uses a large computing cluster to enable Laboratory researchers to...

  17. CMS computing on grid

    International Nuclear Information System (INIS)

    Guan Wen; Sun Gongxing

    2007-01-01

    CMS has adopted a distributed system of services which implement CMS application view on top of Grid services. An overview of CMS services will be covered. Emphasis is on CMS data management and workload Management. (authors)

  18. Technology Roadmaps: Smart Grids

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2011-07-01

    The development of Technology Roadmaps: Smart Grids -- which the IEA defines as an electricity network that uses digital and other advanced technologies to monitor and manage the transport of electricity from all generation sources to meet the varying electricity demands of end users -- is essential if the global community is to achieve shared goals for energy security, economic development and climate change mitigation. Unfortunately, existing misunderstandings of exactly what smart grids are and the physical and institutional complexity of electricity systems make it difficult to implement smart grids on the scale that is needed. This roadmap sets out specific steps needed over the coming years to achieve milestones that will allow smart grids to deliver a clean energy future.

  19. Meet the Grid

    CERN Multimedia

    Yurkewicz, Katie

    2005-01-01

    Today's cutting-edge scientific projects are larger, more complex, and more expensive than ever. Grid computing provides the resources that allow researchers to share knowledge, data, and computer processing power across boundaries

  20. World Wide Grid

    CERN Multimedia

    Grätzel von Grätz, Philipp

    2007-01-01

    Whether for genetic risk analysis or 3D-rekonstruktion of the cerebral vessels: the modern medicine requires more computing power. With a grid infrastructure, this one can be if necessary called by the network. (4 pages)

  1. Spacer grid corner gusset

    International Nuclear Information System (INIS)

    Larson, J.G.

    1984-01-01

    There is provided a spacer grid for a bundle of longitudinally extending rods in spaced generally parallel relationship comprising spacing means for holding the rods in spaced generally parallel relationship; the spacing means includes at least one exterior grid strip circumscribing the bundle of rods along the periphery thereof; with at least one exterior grid strip having a first edge defining the boundary of the strip in one longitudinal direction and a second edge defining the boundary of the strip in the other longitudinal direction; with at least one exterior grid strip having at least one band formed therein parallel to the longitudinal direction; a plurality of corner gussets truncating each of a plurality of corners formed by at least one band and the first edge and the second edge

  2. Smart grids - French Expertise

    International Nuclear Information System (INIS)

    2015-11-01

    The adaptation of electrical systems is the focus of major work worldwide. Bringing electricity to new territories, modernizing existing electricity grids, implementing energy efficiency policies and deploying renewable energies, developing new uses for electricity, introducing electric vehicles - these are the challenges facing a multitude of regions and countries. Smart Grids are the result of the convergence of electrical systems technologies with information and communications technologies. They play a key role in addressing the above challenges. Smart Grid development is a major priority for both public and private-sector actors in France. The experience of French companies has grown with the current French electricity system, a system that already shows extensive levels of 'intelligence', efficiency and competitiveness. French expertise also leverages substantial competence in terms of 'systems engineering', and can provide a tailored response to meet all sorts of needs. French products and services span all the technical and commercial building blocks that make up the Smart Grid value chain. They address the following issues: Improving the use and valuation of renewable energies and decentralized means of production, by optimizing the balance between generation and consumption. Strengthening the intelligence of the transmission and distribution grids: developing 'Supergrid', digitizing substations in transmission networks, and automating the distribution grids are the focus of a great many projects designed to reinforce the 'self-healing' capacity of the grid. Improving the valuation of decentralized flexibilities: this involves, among others, deploying smart meters, reinforcing active energy efficiency measures, and boosting consumers' contribution to grid balancing, via practices such as demand response which implies the aggregation of flexibility among residential, business, and/or industrial sites. Addressing current technological challenges, in

  3. US National Grid

    Data.gov (United States)

    Kansas Data Access and Support Center — This is a polygon feature data layer of United States National Grid (1000m x 1000m polygons ) constructed by the Center for Interdisciplinary Geospatial Information...

  4. Controlling smart grid adaptivity

    NARCIS (Netherlands)

    Toersche, Hermen; Nykamp, Stefan; Molderink, Albert; Hurink, Johann L.; Smit, Gerardus Johannes Maria

    2012-01-01

    Methods are discussed for planning oriented smart grid control to cope with scenarios with limited predictability, supporting an increasing penetration of stochastic renewable resources. The performance of these methods is evaluated with simulations using measured wind generation and consumption

  5. Grid Computing Education Support

    Energy Technology Data Exchange (ETDEWEB)

    Steven Crumb

    2008-01-15

    The GGF Student Scholar program enabled GGF the opportunity to bring over sixty qualified graduate and under-graduate students with interests in grid technologies to its three annual events over the three-year program.

  6. Assessing consumer benefits of selected gas appliance technology center tasks. Topical report, April-December 1992

    International Nuclear Information System (INIS)

    Smith, T.R.; Bournakis, A.D.; Worek, W.M.; Kalensky, D.C.; Dombrowski, L.P.

    1992-12-01

    The Gas Appliance Technology Center (GATC) was created in 1983 to assist the gas industry in bringing about a new generation of reasonably priced, advanced gas appliances. The objective of the report is to evaluate consumer benefits of sixteen selected GATC tasks for the time period between 1983 and 1990. Tasks were selected for review based upon their degree of industry impact and how well they represented activities in the four targeted research areas of Space Conditioning, Commercial Appliances, Residential Appliances, and Codes and Standards

  7. A modified palatal crib appliance for children with predetermined thumb-sucking habit - Case report

    International Nuclear Information System (INIS)

    AlEmran, Sulaiman

    2008-01-01

    The aim of this case report was to introduce a modified design of palatal crib habit breaking appliance that can be used for children with predetermined thumb-sucking habit. The appliance is made of two bands on the upper first permanent molars and an extended metal framework to cover the anterior of the palatal roof. The appliance was applied for 4 months on an 8-year-old boy who persistently continued the habit of thumb-sucking. The appliance proved to be very effective for arresting thumb-sucking habit. (author)

  8. The impact of personality on adult patients' adjustability to orthodontic appliances.

    Science.gov (United States)

    Cooper-Kazaz, Rena; Ivgi, Inbal; Canetti, Laura; Bachar, Eytan; Tsur, Boaz; Chaushu, Stella; Shalish, Miriam

    2013-01-01

    To evaluate the impact of psychological traits on patients' choice of orthodontic appliances and their adjustability to orthodontic treatment. The sample consisted of 68 adult patients divided into three groups (28 buccal, 19 lingual, and 21 clear aligners). Prior to treatment participants filled out the Brief Symptom Inventory to assess symptoms of mental distress and the Narcissistic Vulnerability Scale to assess narcissistic personality traits. During the first week after appliance delivery and on day 14, patients completed a Health-Related Quality of Life questionnaire to assess their perception of pain and four areas of dysfunction. The correlation between personality traits and patients' reaction to treatment was evaluated. Somatization was the only trait that affected the choice of lingual and clear aligner appliance. Reduced self-esteem regulation was associated with increased pain in all patients, while exploitation was associated with pain in lingual patients. Narcissistic vulnerability slightly influenced patients' adaptability to orthodontic appliances. Although adjustability to lingual appliances was the most difficult, only two parameters were affected by personality features. In the buccal group, adjustability was affected by numerous parameters. Adaptation to the clear aligner appliance was relatively uneventful and least affected by psychological features. Anxious individuals tend to prefer lingual and clear aligner appliances. The selection of lingual and clear aligner appliances governs the patient's response and recovery process, leaving little room for the effect of psychological features. On the other hand, the buccal appliance allows for greater impact of personality traits on adjustability.

  9. When do energy-efficient appliances generate energy savings? Some evidence from Canada

    International Nuclear Information System (INIS)

    Young, Denise

    2008-01-01

    Improvements in the energy efficiency of household appliances have the potential to decrease residential energy use, but these reductions accrue gradually over time as newer appliances replace older models. SHEU-2003 data are used to examine appliance replacement patterns in Canada for refrigerators, freezers, dishwashers, clothes washers and clothes dryers. The data indicate that the ages at which appliances are replaced tend to be lowest for dishwashers and highest for freezers, with over 40% of freezers in use for more than 20 years before being retired. The life spans of Canadian appliances are compared to the underlying assumptions regarding appliance lifetimes used in models of residential energy demand. We find that Canadian appliance retirement patterns differ from those assumed in the previous literature. Socioeconomic factors related to appliance replacement are also examined. We find that replacement patterns can be sensitive to household characteristics such as income, providing evidence that there may be scope for targeted policies aimed at inducing earlier replacements of older household appliances with new energy-efficient models

  10. Beyond grid security

    International Nuclear Information System (INIS)

    Hoeft, B; Epting, U; Koenig, T

    2008-01-01

    While many fields relevant to Grid security are already covered by existing working groups, their remit rarely goes beyond the scope of the Grid infrastructure itself. However, security issues pertaining to the internal set-up of compute centres have at least as much impact on Grid security. Thus, this talk will present briefly the EU ISSeG project (Integrated Site Security for Grids). In contrast to groups such as OSCT (Operational Security Coordination Team) and JSPG (Joint Security Policy Group), the purpose of ISSeG is to provide a holistic approach to security for Grid computer centres, from strategic considerations to an implementation plan and its deployment. The generalised methodology of Integrated Site Security (ISS) is based on the knowledge gained during its implementation at several sites as well as through security audits, and this will be briefly discussed. Several examples of ISS implementation tasks at the Forschungszentrum Karlsruhe will be presented, including segregation of the network for administration and maintenance and the implementation of Application Gateways. Furthermore, the web-based ISSeG training material will be introduced. This aims to offer ISS implementation guidance to other Grid installations in order to help avoid common pitfalls

  11. Near-Body Grid Adaption for Overset Grids

    Science.gov (United States)

    Buning, Pieter G.; Pulliam, Thomas H.

    2016-01-01

    A solution adaption capability for curvilinear near-body grids has been implemented in the OVERFLOW overset grid computational fluid dynamics code. The approach follows closely that used for the Cartesian off-body grids, but inserts refined grids in the computational space of original near-body grids. Refined curvilinear grids are generated using parametric cubic interpolation, with one-sided biasing based on curvature and stretching ratio of the original grid. Sensor functions, grid marking, and solution interpolation tasks are implemented in the same fashion as for off-body grids. A goal-oriented procedure, based on largest error first, is included for controlling growth rate and maximum size of the adapted grid system. The adaption process is almost entirely parallelized using MPI, resulting in a capability suitable for viscous, moving body simulations. Two- and three-dimensional examples are presented.

  12. Intermediate peer contexts and educational outcomes: Do the friends of students' friends matter?

    Science.gov (United States)

    Carbonaro, William; Workman, Joseph

    2016-07-01

    Sociologists of education have long been interested in the effects of peer relations on educational outcomes. Recent theory and research on adolescence suggest that peers on the boundaries of students' friendship networks may play an important role in shaping behaviors and educational outcomes. In this study, we examine the importance of a key "intermediate peer context" for students' outcomes: the friends of a student's friends. Our findings indicate both friends' and friends' friends' characteristics independently predict students' college expectations and their risk of dropping out of high school (although only friends' characteristics predict GPA). Our models suggest the magnitude of students' friends-of-friends' characteristics are at least as large their friends' characteristics. Together, the association between the peer context and students outcomes is considerably larger when accounting for both the characteristics of students' friends and the friends of their friends. Copyright © 2016 Elsevier Inc. All rights reserved.

  13. The Benefits of Grid Networks

    Science.gov (United States)

    Tennant, Roy

    2005-01-01

    In the article, the author talks about the benefits of grid networks. In speaking of grid networks the author is referring to both networks of computers and networks of humans connected together in a grid topology. Examples are provided of how grid networks are beneficial today and the ways in which they have been used.

  14. Smart Grid Integration Laboratory

    Energy Technology Data Exchange (ETDEWEB)

    Troxell, Wade [Colorado State Univ., Fort Collins, CO (United States)

    2011-12-22

    The initial federal funding for the Colorado State University Smart Grid Integration Laboratory is through a Congressionally Directed Project (CDP), DE-OE0000070 Smart Grid Integration Laboratory. The original program requested in three one-year increments for staff acquisition, curriculum development, and instrumentation all which will benefit the Laboratory. This report focuses on the initial phase of staff acquisition which was directed and administered by DOE NETL/ West Virginia under Project Officer Tom George. Using this CDP funding, we have developed the leadership and intellectual capacity for the SGIC. This was accomplished by investing (hiring) a core team of Smart Grid Systems engineering faculty focused on education, research, and innovation of a secure and smart grid infrastructure. The Smart Grid Integration Laboratory will be housed with the separately funded Integrid Laboratory as part of CSU's overall Smart Grid Integration Center (SGIC). The period of performance of this grant was 10/1/2009 to 9/30/2011 which included one no cost extension due to time delays in faculty hiring. The Smart Grid Integration Laboratory's focus is to build foundations to help graduate and undergraduates acquire systems engineering knowledge; conduct innovative research; and team externally with grid smart organizations. Using the results of the separately funded Smart Grid Workforce Education Workshop (May 2009) sponsored by the City of Fort Collins, Northern Colorado Clean Energy Cluster, Colorado State University Continuing Education, Spirae, and Siemens has been used to guide the hiring of faculty, program curriculum and education plan. This project develops faculty leaders with the intellectual capacity to inspire its students to become leaders that substantially contribute to the development and maintenance of Smart Grid infrastructure through topics such as: (1) Distributed energy systems modeling and control; (2) Energy and power conversion; (3

  15. Distributed computing grid experiences in CMS

    CERN Document Server

    Andreeva, Julia; Barrass, T; Bonacorsi, D; Bunn, Julian; Capiluppi, P; Corvo, M; Darmenov, N; De Filippis, N; Donno, F; Donvito, G; Eulisse, G; Fanfani, A; Fanzago, F; Filine, A; Grandi, C; Hernández, J M; Innocente, V; Jan, A; Lacaprara, S; Legrand, I; Metson, S; Newbold, D; Newman, H; Pierro, A; Silvestris, L; Steenberg, C; Stockinger, H; Taylor, Lucas; Thomas, M; Tuura, L; Van Lingen, F; Wildish, Tony

    2005-01-01

    The CMS experiment is currently developing a computing system capable of serving, processing and archiving the large number of events that will be generated when the CMS detector starts taking data. During 2004 CMS undertook a large scale data challenge to demonstrate the ability of the CMS computing system to cope with a sustained data- taking rate equivalent to 25% of startup rate. Its goals were: to run CMS event reconstruction at CERN for a sustained period at 25 Hz input rate; to distribute the data to several regional centers; and enable data access at those centers for analysis. Grid middleware was utilized to help complete all aspects of the challenge. To continue to provide scalable access from anywhere in the world to the data, CMS is developing a layer of software that uses Grid tools to gain access to data and resources, and that aims to provide physicists with a user friendly interface for submitting their analysis jobs. This paper describes the data challenge experience with Grid infrastructure ...

  16. Mechanical appliances, mechanical movements and novelties of construction

    CERN Document Server

    Hiscox, Gardner D

    2008-01-01

    From the devices that power ships and trains to the workings of clocks, typewriters, and guns, this engrossing visual narrative profiles the specific and unique properties of hundreds of mechanical devices. Nearly 1,000 detailed illustrations depict steam-powered appliances, spring-powered devices, hydraulic equipment, and other machines, many of which remain in common use today. Each apparatus features a detailed line drawing and an informative explanation of its workings and uses. A final chapter chronicles 400 years of impassioned but futile searching for a perpetual motion machine.The comp

  17. Simplified feeding appliance for an infant with cleft palate

    Directory of Open Access Journals (Sweden)

    Shaila Masih

    2014-01-01

    Full Text Available A child born with cleft palate may experience difficulties while feeding. Early surgical treatment may need to be postponed until certain age and weight gain of the infant. The case presented here is of a 1-month-old neonate born with cleft palate, assisted with a new feeding appliance made with ethylene vinyl acetate using pressure molding technique to aid in proper feeding. The patient′s weight and health significantly improved after the insertion of obturator. The advantages of this material included being lightweight, moldability, good palatal fit and decreased soft tissue injury.

  18. Prediction of appliances energy use in smart homes

    International Nuclear Information System (INIS)

    Arghira, Nicoleta; Hawarah, Lamis; Ploix, Stéphane; Jacomino, Mireille

    2012-01-01

    This paper presents methods for prediction of energy consumption of different appliances in homes. The aim is to predict the next day electricity consumption for some services in homes. Historical data for a set of homes in France was used. Two basic predictors are tested and a stochastic based predictor is proposed. The performance of the predictors is studied and it shows that the proposed predictor gives better results than other approaches. Two processings are proposed to improve the performance of the predictor, segmentation and aggregation of data. Application results are provided.

  19. Appliances facilitating everyday life - electricity use derived from daily activities

    Energy Technology Data Exchange (ETDEWEB)

    Ellegaard, Kajsa (Dept of Thematic Studies, Linkoeping Univ. (Sweden)), e-mail: kajsa.ellegard@liu.se; Widen, Joakim (Dept of Engineering Sciences, Uppsala Univ. (Sweden)); Vrotsou, Katerina (Dept of Science and Technology, Linkoeping Univ. (Sweden))

    2011-06-15

    The purpose of this paper is to present how, using a visualization method, electricity use can be derived from the everyday activity patterns of household members. Target groups are, on the one hand, professionals in the energy sector and energy advisors who need more knowledge about household energy use, and, on the other hand, household members wanting to reduce the energy use by revealing their own habits and thereby finding out how changed activity performance may influence electricity use. The focus is on the relation between utilizing electric appliances to perform everyday life activities and the use of electricity. The visualization method is based on the time-geographic approach developed by Haegerstrand and includes a model that estimates appliance electricity use from household members' activities. Focus, in this paper, is put on some basic activities performed to satisfy daily life needs: cooking and use of information, communication and entertainment devices. These activities appear frequently in the everyday life of households, even though not all household members perform them all. The method is applied on a data material comprising time-diaries written by 463 individuals (aged 10 to 85+) in 179 households in different parts of Sweden. The visualization method reveals when and for how long activities that claim electric appliances are performed by which individual(s). It also shows electricity load curves generated from the use of appliances at different levels, such as individual, household and group or population levels. At household level the method can reveal which household members are the main users of electricity, i.e. the division of labour between household members. Thereby it also informs about whom could be approached by energy companies and energy advisors in information campaigns. The main result of the study is that systematic differences in activity patterns in subgroups of a population can be identified (e.g. men and women) but

  20. New energy test procedures for refrigerators and other appliances; FINAL

    International Nuclear Information System (INIS)

    Meier, Alan; Ernebrant, Stefan; Kawamoto, Kaoru; Wihlborg, Mats

    1999-01-01

    Many innovations in refrigerator design rely on microprocessors, sensors, and algorithms to control automatic defrost, variable speed,and other features. Even though these features strongly influence energy consumption, the major energy test procedures presently test only a refrigerator's mechanical efficiency and ignore the ''software'' aspects. We describe a new test procedure where both ''hardware'' and ''software'' tests are fed into a dynamic simulation model. A wide range of conditions can be tested and simulated. This approach promotes international harmonization because the simulation model can also be programmed to estimate energy use for the ISO, DOE, or JIS test. The approach outlined for refrigerators can also be applied to other appliances

  1. Crozat appliance therapy for an arch-length discrepancy problem.

    Science.gov (United States)

    Parker, M

    1991-01-01

    The case involved a white male subject, aged 10 years 6 months, with a Class I molar relationship complicated by a deep overbite and impaction of all four permanent canines, which were completely blocked out of the arches. The growth rate of the arches was found to be abnormal, and there was premature loss of the deciduous teeth. Over a period of approximately 5 years, with intermittent pauses to allow growth to catch up with treatment, the Crozat removable appliance was used to help establish the arch form and correct the plane of occlusion.

  2. Modified distal shoe appliance--fabrication and clinical performance.

    Science.gov (United States)

    Gujjar, Kumar Raghav; Indushekar, K R; Amith, H V; Sharma, Shefali Li

    2012-01-01

    When the primary second molar is prematurely lost, mesial movement and migration of the permanent first molar often occurs. This is one of the most difficult problems of the developing dentition confronted by pediatric dentists. Use of a space maintainer that will guide the permanent first molar into its normal position is indicated. In cases with bilateral premature loss of primary molars, the conventional design of distal shoe poses a variety of problems and, therefore, necessitates a customized design for the eruption guidance of permanent first molars. The purpose of this case report is to discuss an innovative design of a distal shoe appliance, which was used with good clinical results.

  3. Importance of Grid Center Arrangement

    Science.gov (United States)

    Pasaogullari, O.; Usul, N.

    2012-12-01

    In Digital Elevation Modeling, grid size is accepted to be the most important parameter. Despite the point density and/or scale of the source data, it is freely decided by the user. Most of the time, arrangement of the grid centers are ignored, even most GIS packages omit the choice of grid center coordinate selection. In our study; importance of the arrangement of grid centers is investigated. Using the analogy between "Raster Grid DEM" and "Bitmap Image", importance of placement of grid centers in DEMs are measured. The study has been conducted on four different grid DEMs obtained from a half ellipsoid. These grid DEMs are obtained in such a way that they are half grid size apart from each other. Resulting grid DEMs are investigated through similarity measures. Image processing scientists use different measures to investigate the dis/similarity between the images and the amount of different information they carry. Grid DEMs are projected to a finer grid in order to co-center. Similarity measures are then applied to each grid DEM pairs. These similarity measures are adapted to DEM with band reduction and real number operation. One of the measures gives function graph and the others give measure matrices. Application of similarity measures to six grid DEM pairs shows interesting results. These four different grid DEMs are created with the same method for the same area, surprisingly; thirteen out of 14 measures state that, the half grid size apart grid DEMs are different from each other. The results indicated that although grid DEMs carry mutual information, they have also additional individual information. In other words, half grid size apart constructed grid DEMs have non-redundant information.; Joint Probability Distributions Function Graphs

  4. A comparison between indirect and objective wear-time assessment of removable orthodontic appliances.

    Science.gov (United States)

    Schott, Timm C; Meyer-Gutknecht, Hannes; Mayer, Nicolai; Weber, Joachim; Weimer, Katja

    2017-04-01

    Patients do not always adhere to the wear times prescribed for removable orthodontic appliances. We evaluated the validity and usability of indirect wear-time assessment methods by comparing wear-time estimates with microelectronically measured wear times in patients with removable orthodontic appliances. Wear times of 33 expansion plates, 34 functional appliances, and 42 retention plates of patients aged 6-20 years (12.3±2.9 years, 50.5% female) were indirectly determined by practitioners using a questionnaire assessing five parameters on a 5-point Likert scale: appliance handling, appliance appearance, bite shift, tooth movement, and appliance fit. The perceived difficulty in assessing each parameter was rated. Actual wear times were evaluated with microelectronic sensors in the appliances. Regression analyses revealed that practitioners' decisions about wear times varied depending on the type of appliance and criteria used, with only one standard criterion best predicting estimated wear time for each appliance. Different standard criteria were better predictors of measured wear time: 22.3% of wear-time variability was explained by expansion plate appearance, 31.2% by functional appliance handling, and 18.8% by retainer fitting. However, practitioners rated the difficulty of assessment in most cases as 'easy'. The study was not double blinded for technical reasons, and practitioners may have considered the evaluation criteria more carefully than in normal daily practice. Practitioners' decisions about wear times based on standard criteria strongly vary depending on the type of appliance and criteria used. © The Author 2016. Published by Oxford University Press on behalf of the European Orthodontic Society. All rights reserved. For permissions, please email: journals.permissions@oup.com

  5. GridCom, Grid Commander: graphical interface for Grid jobs and data management

    International Nuclear Information System (INIS)

    Galaktionov, V.V.

    2011-01-01

    GridCom - the software package for maintenance of automation of access to means of distributed system Grid (jobs and data). The client part, executed in the form of Java-applets, realises the Web-interface access to Grid through standard browsers. The executive part Lexor (LCG Executor) is started by the user in UI (User Interface) machine providing performance of Grid operations

  6. Illiquidity and All Its Friends

    OpenAIRE

    Tirole, Jean

    2009-01-01

    The recent crisis was characterized by massive illiquidity. This paper reviews what we know and don't know about illiquidity and all its friends: market freezes, fire sales, contagion, and ultimately insolvencies and bailouts. It first explains why liquidity cannot easily be apprehended through a single statistic, and asks whether liquidity should be regulated given that a capital adequacy requirement is already in place. The paper then analyzes market breakdowns due to either adverse selecti...

  7. French adolescents' environmental friendly behaviour

    OpenAIRE

    Schleyer-Lindenmann, Alexandra

    2012-01-01

    International audience; Environmental friendly behavior and attitudes have been studied in social sciences since the 1970 with the awakening of an « ecological consciousness ». Psychology has been actively taking part in these studies since then (Maloney & Ward, 1973, Oskamp, 2000, Schmuck & Schultz, 2002). Bronfenbrenner (1979) in his nested system approach, sees the person as seen as a developing entity, in constant interaction with different developing environments. We therefore propose to...

  8. Grid and Entrepreneurship Workshop

    CERN Multimedia

    2006-01-01

    The CERN openlab is organising a special workshop about Grid opportunities for entrepreneurship. This one-day event will provide an overview of what is involved in spin-off technology, with a special reference to the context of computing and data Grids. Lectures by experienced entrepreneurs will introduce the key concepts of entrepreneurship and review, in particular, the industrial potential of EGEE (the EU co-funded Enabling Grids for E-sciencE project, led by CERN). Case studies will be given by CEOs of European start-ups already active in the Grid and computing cluster area, and regional experts will provide an overview of efforts in several European regions to stimulate entrepreneurship. This workshop is designed to encourage students and researchers involved or interested in Grid technology to consider the entrepreneurial opportunities that this technology may create in the coming years. This workshop is organized as part of the CERN openlab student programme, which is co-sponsored by CERN, HP, ...

  9. For smart electric grids

    International Nuclear Information System (INIS)

    Tran Thiet, Jean-Paul; Leger, Sebastien; Bressand, Florian; Perez, Yannick; Bacha, Seddik; Laurent, Daniel; Perrin, Marion

    2012-01-01

    The authors identify and discuss the main challenges faced by the French electric grid: the management of electricity demand and the needed improvement of energy efficiency, the evolution of consumer's state of mind, and the integration of new production capacities. They notably outline that France have been living until recently with an electricity abundance, but now faces the highest consumption peaks in Europe, and is therefore facing higher risks of power cuts. They also notice that the French energy mix is slowly evolving, and outline the problems raised by the fact that renewable energies which are to be developed, are decentralised and intermittent. They propose an overview of present developments of smart grids, and outline their innovative characteristics, challenges raised by their development and compare international examples. They show that smart grids enable a better adapted supply and decentralisation. A set of proposals is formulated about how to finance and to organise the reconfiguration of electric grids, how to increase consumer's responsibility for peak management and demand management, how to create the conditions of emergence of a European market of smart grids, and how to support self-consumption and the building-up of an energy storage sector

  10. Future electrical distribution grids: Smart Grids

    International Nuclear Information System (INIS)

    Hadjsaid, N.; Sabonnadiere, J.C.; Angelier, J.P.

    2010-01-01

    The new energy paradigm faced by distribution network represents a real scientific challenge. Thus, national and EU objectives in terms of environment and energy efficiency with resulted regulatory incentives for renewable energies, the deployment of smart meters and the need to respond to changing needs including new uses related to electric and plug-in hybrid vehicles introduce more complexity and favour the evolution towards a smarter grid. The economic interest group in Grenoble IDEA in connection with the power laboratory G2ELab at Grenoble Institute of technology, EDF and Schneider Electric are conducting research on the electrical distribution of the future in presence of distributed generation for ten years.Thus, several innovations emerged in terms of flexibility and intelligence of the distribution network. One can notice the intelligence solutions for voltage control, the tools of network optimization, the self-healing techniques, the innovative strategies for connecting distributed and intermittent generation or load control possibilities for the distributor. All these innovations are firmly in the context of intelligent networks of tomorrow 'Smart Grids'. (authors)

  11. The Pacific Northwest residential consumer: Perceptions and preferences of home heating fuels, major appliances, and appliance fuels

    Energy Technology Data Exchange (ETDEWEB)

    Harkreader, S.A.; Hattrup, M.P.

    1988-09-01

    In 1983 the Bonneville Power Administration contracted with the Pacific Northwest Laboratory (PNL) to conduct an analysis of the marketing environment for Bonneville's conservation activities. Since this baseline residential study, PNL has conducted two follow up market research projects: Phase 2 in 1985, and Phase 3, in 1988. In this report the respondents' perceptions, preferences, and fuel switching possibilities of fuels for home heating and major appliances are examined. To aid in effective target marketing, the report identifies market segments according to consumers' demographics, life-cycle, attitudes, and opinions.

  12. Survey in Smart Grid and Smart Home Security: Issues, Challenges and Countermeasures

    OpenAIRE

    Komninos, N.; Phillppou, E.; Pitsillides, A.

    2014-01-01

    The electricity industry is now at the verge of a new era. An era that promises, through the evolution of the existing electrical grids to Smart Grids, more efficient and effective power management, better reliability, reduced production costs and more environmentally friendly energy generation. Numerous initiatives across the globe, led by both industry and academia, reflect the mounting interest around the enormous benefits but also the great risks introduced by this evolution. This paper f...

  13. 75 FR 63851 - Draft Friends Organizations Policy

    Science.gov (United States)

    2010-10-18

    ...] Draft Friends Organizations Policy AGENCY: Fish and Wildlife Service, Department of the Interior. ACTION... Service's mission through partnerships with Friends organizations (volunteer/advocate). Today, Friends organizations play a vital role in helping to fulfill the Service's mission of ``working with others, to...

  14. Fermilab Friends for Science Education | Welcome

    Science.gov (United States)

    Fermilab Friends for Science Education FFSE Home About Us Join Us Support Us Contact Us Fermilab Friends for Science Education photo Fermilab Friends for Science Education supports innovative science education programs at Fermilab. Its mission is to: Enhance the quality of precollege science education in

  15. 49 CFR 236.312 - Movable bridge, interlocking of signal appliances with bridge devices.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Movable bridge, interlocking of signal appliances with bridge devices. 236.312 Section 236.312 Transportation Other Regulations Relating to... SYSTEMS, DEVICES, AND APPLIANCES Interlocking Standards § 236.312 Movable bridge, interlocking of signal...

  16. Boundedly rational consumers, energy and investment literacy, and the display of information on household appliances

    NARCIS (Netherlands)

    Blasch, J.E.; Filippini, Massimo; Kumar, Nilkanth

    2017-01-01

    It is an ongoing debate how to increase the adoption of energy-efficient light bulbs and household appliances in the presence of the so-called ‘energy efficiency gap’. One measure to support consumers’ decision-making towards the purchase of more efficient appliances is the display of energy-related

  17. 46 CFR 160.031-4 - Equipment for shoulder gun type line-throwing appliance.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 6 2010-10-01 2010-10-01 false Equipment for shoulder gun type line-throwing appliance... Appliance, Shoulder Gun Type (and Equipment) § 160.031-4 Equipment for shoulder gun type line-throwing... the gun. The line canister shall be secured by clamps or brackets below the barrel of the gun. (c) One...

  18. Greening production and consumption: the case of the appliance and dairy industries in Thailand

    NARCIS (Netherlands)

    Thongplew, N.

    2015-01-01

    Abstract

    Natapol Thongplew

    Thesis title: Greening production and consumption: The case of the appliance and dairy industries in Thailand

    This research looked into the greening of the appliance and dairy industries in

  19. Created in Close Interaction with the Industry: The Smart Appliances REFerence (SAREF) Ontology

    NARCIS (Netherlands)

    Daniele, L.M.; Hartog, F.T.H. den; Roes, J.B.M.

    2015-01-01

    Around two thirds of the energy consumed by buildings can be traced back to the residential sectors and thus household appliances. Today, most appliances are highly intelligent and networked devices, in principle being able to form complete energy consuming, producing, and managing systems. Reducing

  20. What to Do If Your Appliances Are Wet After a Disaster

    Centers for Disease Control (CDC) Podcasts

    2006-08-10

    If your home was flooded, look for signs that your appliances have gotten wet. Throw away wet or flooded appliances to protect from shock and fire.  Created: 8/10/2006 by Emergency Communications System.   Date Released: 7/30/2008.

  1. Efficacy of custom made oral appliance for treatment of obstructive sleep apnea

    Directory of Open Access Journals (Sweden)

    V R Cilil

    2015-01-01

    Full Text Available Introduction: oral appliance for the treatment of OSA is considered as an effective, low-risk alternative to CPAP. Demand for oral appliance increases as an alternative for those who cannot tolerate CPAP and refuse surgery. Oral appliances uses the traditional methods to advance the mandible thus modify the posture and their by enlarge the airway or otherwise reduce the collapsibility. Aims and Objectives: The main objective of this study was to evaluate the efficacy of custom made oral appliance on sleep characteristics of OSA patients. Materials and Methods: Polysomnography was done on 15 patients of 24-60 years of age before (T1, and after the delivery of the custom made oral appliance (T2. Statistical Analysis: Paired t tests were performed to determine the significance of change in the polysomnographic and cephalometric variables. P < 0.05 was considered as significant. Results: All patients with oral appliance showed an improvement in sleep parameters with an increase in sleep efficiency, and desaturation index with the use of oral appliance. ESS and cephalometric findings showed improvement in the sleep apnea in concordance with the sleep parameters. Conclusions: Custom made oral appliance is a useful treatment option for improving quality of sleep and can be considered as an alternative treatment modality.

  2. 78 FR 54450 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Preliminary...

    Science.gov (United States)

    2013-09-04

    ... Shelving and Racks From the People's Republic of China: Preliminary Results of Antidumping Duty... the antidumping duty order on certain kitchen appliance shelving and racks from the People's Republic...\\ is certain kitchen appliance shelving and racks. The subject merchandise is currently classifiable...

  3. 77 FR 72324 - Certain Kitchen Appliance Shelving and Racks from the People's Republic of China: Countervailing...

    Science.gov (United States)

    2012-12-05

    ... Shelving and Racks from the People's Republic of China: Countervailing Duty Administrative Review, 2010... countervailing duty order on certain kitchen appliance shelving and racks from the People's Republic of China. See Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Countervailing...

  4. 77 FR 12811 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Partial...

    Science.gov (United States)

    2012-03-02

    ... Shelving and Racks From the People's Republic of China: Partial Rescission of Antidumping Duty... review of the antidumping duty order on certain kitchen appliance shelving and racks from the People's... Appliance Shelving and Racks from the People's Republic of China, dated January 10, 2012; and Letter to the...

  5. 76 FR 62765 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Preliminary...

    Science.gov (United States)

    2011-10-11

    ... Shelving and Racks From the People's Republic of China: Preliminary Results of the First Administrative... review of the antidumping duty order on certain kitchen appliance shelving and racks from the People's... administrative review of certain kitchen appliance shelving and racks from the PRC for the period March 5, 2009...

  6. Eu-energy label for electric appliances; Das EU-Energielabel fuer Elektrogeraete

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2011-04-15

    When buying a new appliances to have clear and understandable information on energy consumption to avoid later expensive surprices by to high power cost. But European classifiaction A to G of big household appliances is out of date and must be changed.(orig./GL)

  7. Open-bite treatment utilizing clear removable appliances with intermaxillary and intramaxillary elastics.

    Science.gov (United States)

    Park, Jae Hyun; Kim, Tae Weon

    2009-01-01

    Clear removable appliances with elastics can be effective and efficient in extruding maxillary teeth during aligner treatment or following a relapse of an open bite. Some patients with open bites refuse to wear conventional fixed appliances. In these individuals, clear aligners with elastics could be a valuable alternative. © 2009 Quintessence Publishing Co, Inc. All Rights Reserved

  8. How do household characteristics affect appliance usage? Application of conditional demand analysis to Japanese household data

    International Nuclear Information System (INIS)

    Matsumoto, Shigeru

    2016-01-01

    Although both appliance ownership and usage patterns determine residential electricity consumption, it is less known how households actually use their appliances. In this study, we conduct conditional demand analyses to break down total household electricity consumption into a set of demand functions for electricity usage, across 12 appliance categories. We then examine how the socioeconomic characteristics of the households explain their appliance usage. Analysis of micro-level data from the Nation Survey of Family and Expenditure in Japan reveals that the family and income structure of households affect appliance usage. Specifically, we find that the presence of teenagers increases both air conditioner and dishwasher use, labor income and nonlabor income affect microwave usage in different ways, air conditioner usage decreases as the wife's income increases, and microwave usage decreases as the husband's income increases. Furthermore, we find that households use more electricity with new personal computers than old ones; this implies that the replacement of old personal computers increases electricity consumption. - Highlights: •We conduct conditional demand analyses to study household appliance usage. •Micro-level data from the National Survey of Family and Expenditure in Japan are analyzed. •We show how household characteristics determine appliance usage. •High-income households use specific appliances less intensively than low-income households. •The replacement of old TVs and PCs lead to greater electricity consumption.

  9. Analyzing price and efficiency dynamics of large appliances with the experience curve approach

    International Nuclear Information System (INIS)

    Weiss, Martin; Patel, Martin K.; Junginger, Martin; Blok, Kornelis

    2010-01-01

    Large appliances are major power consumers in households of industrialized countries. Although their energy efficiency has been increasing substantially in past decades, still additional energy efficiency potentials exist. Energy policy that aims at realizing these potentials faces, however, growing concerns about possible adverse effects on commodity prices. Here, we address these concerns by applying the experience curve approach to analyze long-term price and energy efficiency trends of three wet appliances (washing machines, laundry dryers, and dishwashers) and two cold appliances (refrigerators and freezers). We identify a robust long-term decline in both specific price and specific energy consumption of large appliances. Specific prices of wet appliances decline at learning rates (LR) of 29±8% and thereby much faster than those of cold appliances (LR of 9±4%). Our results demonstrate that technological learning leads to substantial price decline, thus indicating that the introduction of novel and initially expensive energy efficiency technologies does not necessarily imply adverse price effects in the long term. By extending the conventional experience curve approach, we find a steady decline in the specific energy consumption of wet appliances (LR of 20-35%) and cold appliances (LR of 13-17%). Our analysis suggests that energy policy might be able to bend down energy experience curves. (author)

  10. Toward semantic interoperability of energy using and producing appliances in residential environments

    NARCIS (Netherlands)

    Hartog, F.T.H. den; Daniele, L.M.; Roes, J.B.M.

    2015-01-01

    About two thirds of the energy consumed in buildings originates household appliances. Nowadays, appliances are often intelligent and networked devices that form complete energy consuming, producing, and managing systems. Reducing energy is therefore a matter of managing and optimizing the energy

  11. Effects of mechanical properties of thermoplastic materials on the initial force of thermoplastic appliances.

    Science.gov (United States)

    Kohda, Naohisa; Iijima, Masahiro; Muguruma, Takeshi; Brantley, William A; Ahluwalia, Karamdeep S; Mizoguchi, Itaru

    2013-05-01

    To measure the forces delivered by thermoplastic appliances made from three materials and investigate effects of mechanical properties, material thickness, and amount of activation on orthodontic forces. Three thermoplastic materials, Duran (Scheu Dental), Erkodur (Erkodent Erich Kopp GmbH), and Hardcast (Scheu Dental), with two different thicknesses were selected. Values of elastic modulus and hardness were obtained from nanoindentation measurements at 28°C. A custom-fabricated system with a force sensor was employed to obtain measurements of in vitro force delivered by the thermoplastic appliances for 0.5-mm and 1.0-mm activation for bodily tooth movement. Experimental results were subjected to several statistical analyses. Hardcast had significantly lower elastic modulus and hardness than Duran and Erkodur, whose properties were not significantly different. Appliances fabricated from thicker material (0.75 mm or 0.8 mm) always produced significantly greater force than those fabricated from thinner material (0.4 mm or 0.5 mm). Appliances with 1.0-mm activation produced significantly lower force than those with 0.5-mm activation, except for 0.4-mm thick Hardcast appliances. A strong correlation was found between mechanical properties of the thermoplastic materials and force produced by the appliances. Orthodontic forces delivered by thermoplastic appliances depend on the material, thickness, and amount of activation. Mechanical properties of the polymers obtained by nanoindentation testing are predictive of force delivery by these appliances.

  12. Optimal residential smart appliances scheduling considering distribution network constraints

    Directory of Open Access Journals (Sweden)

    Yu-Ree Kim

    2016-01-01

    Full Text Available As smart appliances (SAs are more widely adopted within distribution networks, residential consumers can contribute to electricity market operations with demand response resources and reduce their electricity bill. However, if the schedules of demand response resources are determined only by the economic electricity rate signal, the schedule can be unfeasible due to the distribution network constraints. Furthermore, it is impossible for consumers to understand the complex physical characteristics and reflect them in their everyday behaviors. This paper introduces the concept of load coordinating retailer (LCR that deals with demand responsive appliances to reduce electrical consumption for the given distribution network constraints. The LCR can play the role of both conventional retailer and aggregated demand response provider for residential customers. It determines the optimal schedules for the aggregated neighboring SAs according to their types within each distribution feeder. The optimization algorithms are developed using Mixed Integer Linear Programming, and the distribution network is solved by the Newton–Raphson AC power flow.

  13. Multimedia architectures: from desktop systems to portable appliances

    Science.gov (United States)

    Bhaskaran, Vasudev; Konstantinides, Konstantinos; Natarajan, Balas R.

    1997-01-01

    Future desktop and portable computing systems will have as their core an integrated multimedia system. Such a system will seamlessly combine digital video, digital audio, computer animation, text, and graphics. Furthermore, such a system will allow for mixed-media creation, dissemination, and interactive access in real time. Multimedia architectures that need to support these functions have traditionally required special display and processing units for the different media types. This approach tends to be expensive and is inefficient in its use of silicon. Furthermore, such media-specific processing units are unable to cope with the fluid nature of the multimedia market wherein the needs and standards are changing and system manufacturers may demand a single component media engine across a range of products. This constraint has led to a shift towards providing a single-component multimedia specific computing engine that can be integrated easily within desktop systems, tethered consumer appliances, or portable appliances. In this paper, we review some of the recent architectural efforts in developing integrated media systems. We primarily focus on two efforts, namely the evolution of multimedia-capable general purpose processors and a more recent effort in developing single component mixed media co-processors. Design considerations that could facilitate the migration of these technologies to a portable integrated media system also are presented.

  14. Grid sleeve bulge tool

    International Nuclear Information System (INIS)

    Phillips, W.D.; Vaill, R.E.

    1980-01-01

    An improved grid sleeve bulge tool is designed for securing control rod guide tubes to sleeves brazed in a fuel assembly grid. The tool includes a cylinder having an outer diameter less than the internal diameter of the control rod guide tubes. The walls of the cylinder are cut in an axial direction along its length to provide several flexible tines or ligaments. These tines are similar to a fork except they are spaced in a circumferential direction. The end of each alternate tine is equipped with a semispherical projection which extends radially outwardly from the tine surface. A ram or plunger of generally cylindrical configuration and about the same length as the cylinder is designed to fit in and move axially of the cylinder and thereby force the tined projections outwardly when the ram is pulled into the cylinder. The ram surface includes axially extending grooves and plane surfaces which are complimentary to the inner surfaces formed on the tines on the cylinder. As the cylinder is inserted into a control rod guide tube, and the projections on the cylinder placed in a position just below or above a grid strap, the ram is pulled into the cylinder, thus moving the tines and the projections thereon outwardly into contact with the sleeve, to plastically deform both the sleeve and the control rod guide tube, and thereby form four bulges which extend outwardly from the sleeve surface and beyond the outer periphery of the grid peripheral strap. This process is then repeated at the points above the grid to also provide for outwardly projecting surfaces, the result being that the grid is accurately positioned on and mechanically secured to the control rod guide tubes which extend the length of a fuel assembly

  15. Treatment of adolescent patients with class II division 1 malocclusion using Eruption guidance appliance: A comparative study with Twin-block and Activator-Headgear appliances.

    Science.gov (United States)

    Nilsson, Jenny Jiayan Luo; Shu, Xiaochen; Magnusson, Britt Hedenberg; Burt, Idil Alatli

    2016-01-01

    The aim of this study was to evaluate the compliance and short-term effects of eruption guidance appliance (EGA) in adolescents with class II division 1 malocclusion in comparison with twin-block appliance (TBA) and activator-headgear appliance (A-HG). Dental records of 1886 patients were viewed in this retrospective study 129 patients treated with one of these three functional appliances were identified. 123 fulfilled the inclusion criteria and data were extracted from the dental records. Gender, age, compliance, overjet change at every visit, number of appliance breakages and number of emergency visits apart from appliance breakage were studied. The data were analyzed with Chi-square test, General Linear Model and Fisher scoring test. Results showed that 47 patients were treated with EGA, 38 patients with TBA and 38 patients with A-HG. Mean ages starting the treatment were slightly lower with EGA (11.5 years) than with TBA (12.3 years) and A-HG (11.8 years). Non-compliance was higher in the EGA group (31.9%) than TBA group (26.3%) and A-HG group (23.7%). Mean overjet reduction per month was 0.6 mm for EGA which was lower than TBA group (0.7 mm) and A-HG groups (0.7 mm).The number of emergency visits and appliance breakage were lower in EGA group. However, there was no statistically significant difference between the 3 groups regarding ages,compliance, mean overjet reduction, emergency visits and appliance breakage aspects. In conclusion, this study indicates that EGA is an alternative choice in the treatment of adolescent patients with class II division 1 malocclusion. However, long-term follow-up and cephalometric prospective study should be performed to continue our understanding more about the mechanisms of EGA and more definite conclusions can be made.

  16. Grids, Clouds and Virtualization

    CERN Document Server

    Cafaro, Massimo

    2011-01-01

    Research into grid computing has been driven by the need to solve large-scale, increasingly complex problems for scientific applications. Yet the applications of grid computing for business and casual users did not begin to emerge until the development of the concept of cloud computing, fueled by advances in virtualization techniques, coupled with the increased availability of ever-greater Internet bandwidth. The appeal of this new paradigm is mainly based on its simplicity, and the affordable price for seamless access to both computational and storage resources. This timely text/reference int

  17. Smart Grid Architectures

    DEFF Research Database (Denmark)

    Dondossola, Giovanna; Terruggia, Roberta; Bessler, Sandford

    2014-01-01

    The scope of this paper is to address the evolution of distribution grid architectures following the widespread introduction of renewable energy sources. The increasing connection of distributed resources has a strong impact on the topology and the control functionality of the current distribution...... grids requiring the development of new Information and Communication Technology (ICT) solutions with various degrees of adaptation of the monitoring, communication and control technologies. The costs of ICT based solutions need however to be taken into account, hence it is desirable to work...

  18. Instant jqGrid

    CERN Document Server

    Manricks, Gabriel

    2013-01-01

    Get to grips with a new technology, understand what it is and what it can do for you, and then get to work with the most important features and tasks. A step-by-step, practical Starter book, Instant jqGrid embraces you while you take your first steps, and introduces you to the content in an easy-to-follow order.This book is aimed at people who have some knowledge of HTML and JavaScript. Knowledge of PHP and SQL would also prove to be beneficial. No prior knowledge of jqGrid is expected.

  19. Smart Grid, Smart Europe

    OpenAIRE

    VITIELLO SILVIA; FULLI Gianluca; MENGOLINI Anna Maria

    2013-01-01

    Le smart grid, o reti elettriche intelligenti, aprono la strada a nuove applicazioni con conseguenze di vasta portata per l’intero sistema elettrico, tra le quali la principale è la capacità di integrare nella rete esistente più fonti di energia rinnovabili (FER), veicoli elettrici e fonti di generazione distribuita. Le smart grid inoltre garantiscono una più efficiente ed affidabile risposta alla domanda di energia, sia da un punto di vista tecnico, permettendo un monitoraggio e un controll...

  20. Distributed photovoltaic grid transformers

    CERN Document Server

    Shertukde, Hemchandra Madhusudan

    2014-01-01

    The demand for alternative energy sources fuels the need for electric power and controls engineers to possess a practical understanding of transformers suitable for solar energy. Meeting that need, Distributed Photovoltaic Grid Transformers begins by explaining the basic theory behind transformers in the solar power arena, and then progresses to describe the development, manufacture, and sale of distributed photovoltaic (PV) grid transformers, which help boost the electric DC voltage (generally at 30 volts) harnessed by a PV panel to a higher level (generally at 115 volts or higher) once it is

  1. Assessment of Human Exposure to Magnetic Fields Produced by Domestic Appliances (invited paper)

    International Nuclear Information System (INIS)

    Preece, A.W.; Kaune, W.T.; Grainger, P.; Golding, J.

    1999-01-01

    A study of 50 homes and their appliances examined whether a detailed appliance-use questionnaire and survey would yield data comparable with direct personal monitoring. This was coupled with direct measurement of the appliances in use to determine the field at 50 cm and 1 m. The findings were that individual time-weighted average (TWA) exposures calculated from questionnaire and activity diaries in conjunction with the appliance magnetic field were unrelated to actual personal exposure measurement. It was concluded that questionnaires are of little or no value for TWA estimation. However, peak exposure and short-term temporal variability could be modelled in subjects spending at least 15 min per day within 1 m of an operating microwave cooker or conventional cooker. This method could be extended to other appliances. (author)

  2. Simulation platform for direct load control of household appliances. Literature survey and G2 implementation

    Energy Technology Data Exchange (ETDEWEB)

    Kolm, J; Vlaheli, A

    1996-10-01

    There is an incentive for the power utilities to look for other ways than building new power stations to satisfy increasing customer power needs. One way to fulfill this demand is by redistributing the available electric power between the different power consumers. This method can successfully be used during high peak hours. The utility is also able to make financial profits selling the redistributed electric power at a higher price to customers with temporary high power demands. Direct Load Control - DLC, a Demand Side Management - DSM tool, is one way to achieve a redistribution of electric power. This masters thesis project consisted in developing a user-friendly simulation platform for domestic appliances combined with an electric power control system to be employed for Direct Load Control. The platform contains the necessary facilities for designing an electrical distribution network model and is implemented in G2, an object-oriented real-time environment. The final application provides an on-line instrument for the utility to control the power consumption over the entire system in terms of dispensing power in an electrical network. The report consists of two main parts. The first part describes a literature survey we systematically compiled to gather literature sources. The second part outlines our design and implementation of the G2 simulation platform for a water-heater model with a Direct Load Control system. The entire simulation platform is designed to allow a flexible change and improvement of the different models. Consequently, our software is a powerful tool for studying a wide range of problems related to a Load Management program involving electrical household loads. 9 refs, 32 figs

  3. Application of DC-AC Hybrid Grid and Solar Photovoltaic Generation with Battery Storage Using Smart Grid

    Directory of Open Access Journals (Sweden)

    Shoaib Rauf

    2017-01-01

    Full Text Available Smart grid for the past few years has been the prime focus of research in power systems. The aim is to eliminate load shedding and problematic blackout conditions, further offering cheap and continuous supply of electricity for both large and small consumers. Another benefit is to integrate renewable energy resources with existing dump grid in more efficient and cost-effective manner. In past few years, growing demand for sustainable energy increases the consumption of solar PV. Since generation from solar PV is in DC and most of the appliances at home could be operated on DC, AC-DC hybrid distribution system with energy management system is proposed in this paper. EMS helps to shift or control the auxiliary load and compel the users to operate specific load at certain time slots. These techniques further help to manage the excessive load during peak and off peak hours. It demonstrates the practical implementation of DC-AC network with integration of solar PV and battery storage with existing infrastructure. The results show a remarkable improvement using hybrid AC-DC framework in terms of reliability and efficiency. All this functioning together enhances the overall efficiency; hence, a secure, economical, reliable, and intelligent system leads to a smart grid.

  4. Routines for interocclusal appliance therapy among general dental practitioners in a Swedish county.

    Science.gov (United States)

    Gnauck, Maja; Helkimo, Martti; Magnusson, Tomas

    2012-01-01

    The aims of this study were to investigate what kind of interocclusal appliances that were chosen among Swedish dentists when treating temporomandibular disorders (TMD), the clinical rationale for the treatment, the diagnoses that warranted the appliance treatment, the use of adjunct TMD treatments and prognostic considerations, and possible differences in these respects between children/adolescents and adults with TMD, and, finally, possible differences between private practitioners and general practitioners in the public dental service. During the 12-months-period April 2009-March 2010 all general dental practitioners in the county of Jönköping, Sweden, were asked to fill in a questionnaire when performing a TMD treatment with an interocclusal appliance. A total of 394 questionnaires were filled in and returned, 216 (55%) from dentists in public dental service and 178 (45%) from private practitioners. It was found that in 40% of the cases, no pre-treatment recording of the functional status in the masticatory system had been made. The commonest reasons for the treatment were bruxism, headache, and replacement of a previous appliance. Less than half of the appliances made were hard acrylic appliances. Some kind of adjunct therapy had been made in 22% of the cases treated in public dental service. The corresponding figure for those treated by private practitioners was 25%. Therapeutic jaw exercises was the commonest adjunct therapy followed by selective occlusal adjustment. In the vast majority of cases, the dentists judged the prognosis of the treatment to be good. It is concluded that a large number of appliances made to treat TMD were soft appliances, especially in public dental service. This reflects a possible overuse of soft appliances at the expense of hard acrylic appliances. Furthermore, in a large number of cases, the treatment was performed without any pre-treatment registrations, and adjunct therapies were rarely used. In all these respects,there is

  5. Grid computing the European Data Grid Project

    CERN Document Server

    Segal, B; Gagliardi, F; Carminati, F

    2000-01-01

    The goal of this project is the development of a novel environment to support globally distributed scientific exploration involving multi- PetaByte datasets. The project will devise and develop middleware solutions and testbeds capable of scaling to handle many PetaBytes of distributed data, tens of thousands of resources (processors, disks, etc.), and thousands of simultaneous users. The scale of the problem and the distribution of the resources and user community preclude straightforward replication of the data at different sites, while the aim of providing a general purpose application environment precludes distributing the data using static policies. We will construct this environment by combining and extending newly emerging "Grid" technologies to manage large distributed datasets in addition to computational elements. A consequence of this project will be the emergence of fundamental new modes of scientific exploration, as access to fundamental scientific data is no longer constrained to the producer of...

  6. Decentralized control of units in smart grids for the support of renewable energy supply

    Energy Technology Data Exchange (ETDEWEB)

    Sonnenschein, Michael, E-mail: Michael.Sonnenschein@Uni-Oldenburg.DE [University of Oldenburg, Department of Computing Science, D-26111 Oldenburg (Germany); Lünsdorf, Ontje, E-mail: Ontje.Luensdorf@OFFIS.DE [OFFIS Institute for Information Technology, Escherweg 2, D-26121 Oldenburg (Germany); Bremer, Jörg, E-mail: Joerg.Bremer@Uni-Oldenburg.DE [University of Oldenburg, Department of Computing Science, D-26111 Oldenburg (Germany); Tröschel, Martin, E-mail: Martin.Troeschel@OFFIS.DE [OFFIS Institute for Information Technology, Escherweg 2, D-26121 Oldenburg (Germany)

    2015-04-15

    Due to the significant environmental impact of power production from fossil fuels and nuclear fission, future energy systems will increasingly rely on distributed and renewable energy sources (RES). The electrical feed-in from photovoltaic (PV) systems and wind energy converters (WEC) varies greatly both over short and long time periods (from minutes to seasons), and (not only) by this effect the supply of electrical power from RES and the demand for electrical power are not per se matching. In addition, with a growing share of generation capacity especially in distribution grids, the top-down paradigm of electricity distribution is gradually replaced by a bottom-up power supply. This altogether leads to new problems regarding the safe and reliable operation of power grids. In order to address these challenges, the notion of Smart Grids has been introduced. The inherent flexibilities, i.e. the set of feasible power schedules, of distributed power units have to be controlled in order to support demand–supply matching as well as stable grid operation. Controllable power units are e.g. combined heat and power plants, power storage systems such as batteries, and flexible power consumers such as heat pumps. By controlling the flexibilities of these units we are particularly able to optimize the local utilization of RES feed-in in a given power grid by integrating both supply and demand management measures with special respect to the electrical infrastructure. In this context, decentralized systems, autonomous agents and the concept of self-organizing systems will become key elements of the ICT based control of power units. In this contribution, we first show how a decentralized load management system for battery charging/discharging of electrical vehicles (EVs) can increase the locally used share of supply from PV systems in a low voltage grid. For a reliable demand side management of large sets of appliances, dynamic clustering of these appliances into uniformly

  7. Decentralized control of units in smart grids for the support of renewable energy supply

    International Nuclear Information System (INIS)

    Sonnenschein, Michael; Lünsdorf, Ontje; Bremer, Jörg; Tröschel, Martin

    2015-01-01

    Due to the significant environmental impact of power production from fossil fuels and nuclear fission, future energy systems will increasingly rely on distributed and renewable energy sources (RES). The electrical feed-in from photovoltaic (PV) systems and wind energy converters (WEC) varies greatly both over short and long time periods (from minutes to seasons), and (not only) by this effect the supply of electrical power from RES and the demand for electrical power are not per se matching. In addition, with a growing share of generation capacity especially in distribution grids, the top-down paradigm of electricity distribution is gradually replaced by a bottom-up power supply. This altogether leads to new problems regarding the safe and reliable operation of power grids. In order to address these challenges, the notion of Smart Grids has been introduced. The inherent flexibilities, i.e. the set of feasible power schedules, of distributed power units have to be controlled in order to support demand–supply matching as well as stable grid operation. Controllable power units are e.g. combined heat and power plants, power storage systems such as batteries, and flexible power consumers such as heat pumps. By controlling the flexibilities of these units we are particularly able to optimize the local utilization of RES feed-in in a given power grid by integrating both supply and demand management measures with special respect to the electrical infrastructure. In this context, decentralized systems, autonomous agents and the concept of self-organizing systems will become key elements of the ICT based control of power units. In this contribution, we first show how a decentralized load management system for battery charging/discharging of electrical vehicles (EVs) can increase the locally used share of supply from PV systems in a low voltage grid. For a reliable demand side management of large sets of appliances, dynamic clustering of these appliances into uniformly

  8. A fast algorithm for identifying friends-of-friends halos

    Science.gov (United States)

    Feng, Y.; Modi, C.

    2017-07-01

    We describe a simple and fast algorithm for identifying friends-of-friends features and prove its correctness. The algorithm avoids unnecessary expensive neighbor queries, uses minimal memory overhead, and rejects slowdown in high over-density regions. We define our algorithm formally based on pair enumeration, a problem that has been heavily studied in fast 2-point correlation codes and our reference implementation employs a dual KD-tree correlation function code. We construct features in a hierarchical tree structure, and use a splay operation to reduce the average cost of identifying the root of a feature from O [ log L ] to O [ 1 ] (L is the size of a feature) without additional memory costs. This reduces the overall time complexity of merging trees from O [ L log L ] to O [ L ] , reducing the number of operations per splay by orders of magnitude. We next introduce a pruning operation that skips merge operations between two fully self-connected KD-tree nodes. This improves the robustness of the algorithm, reducing the number of merge operations in high density peaks from O [δ2 ] to O [ δ ] . We show that for cosmological data set the algorithm eliminates more than half of merge operations for typically used linking lengths b ∼ 0 . 2 (relative to mean separation). Furthermore, our algorithm is extremely simple and easy to implement on top of an existing pair enumeration code, reusing the optimization effort that has been invested in fast correlation function codes.

  9. 33 CFR 150.504 - When must the operator service and examine lifeboat and rescue boat launching appliances?

    Science.gov (United States)

    2010-07-01

    ... and examine lifeboat and rescue boat launching appliances? 150.504 Section 150.504 Navigation and...: OPERATIONS Emergency and Specialty Equipment Launching Appliances § 150.504 When must the operator service and examine lifeboat and rescue boat launching appliances? (a) The operator must service launching...

  10. 40 CFR Appendix C to Subpart F of... - Method for Testing Recovery Devices for Use With Small Appliances

    Science.gov (United States)

    2010-07-01

    ... for Use With Small Appliances C Appendix C to Subpart F of Part 82 Protection of Environment... Recovery Devices for Use With Small Appliances Recovery Efficiency Test Procedure for Refrigerant Recovery Equipment Used on Small Appliances The following test procedure is utilized to evaluate the efficiency of...

  11. 33 CFR 150.506 - When must the operator service inflatable lifesaving appliances and marine evacuation systems?

    Science.gov (United States)

    2010-07-01

    ... inflatable lifesaving appliances and marine evacuation systems? 150.506 Section 150.506 Navigation and...: OPERATIONS Emergency and Specialty Equipment Inflatable Lifesaving Appliances § 150.506 When must the operator service inflatable lifesaving appliances and marine evacuation systems? (a) The operator must...

  12. Enabling Campus Grids with Open Science Grid Technology

    International Nuclear Information System (INIS)

    Weitzel, Derek; Fraser, Dan; Pordes, Ruth; Bockelman, Brian; Swanson, David

    2011-01-01

    The Open Science Grid is a recognized key component of the US national cyber-infrastructure enabling scientific discovery through advanced high throughput computing. The principles and techniques that underlie the Open Science Grid can also be applied to Campus Grids since many of the requirements are the same, even if the implementation technologies differ. We find five requirements for a campus grid: trust relationships, job submission, resource independence, accounting, and data management. The Holland Computing Center's campus grid at the University of Nebraska-Lincoln was designed to fulfill the requirements of a campus grid. A bridging daemon was designed to bring non-Condor clusters into a grid managed by Condor. Condor features which make it possible to bridge Condor sites into a multi-campus grid have been exploited at the Holland Computing Center as well.

  13. Enabling campus grids with open science grid technology

    Energy Technology Data Exchange (ETDEWEB)

    Weitzel, Derek [Nebraska U.; Bockelman, Brian [Nebraska U.; Swanson, David [Nebraska U.; Fraser, Dan [Argonne; Pordes, Ruth [Fermilab

    2011-01-01

    The Open Science Grid is a recognized key component of the US national cyber-infrastructure enabling scientific discovery through advanced high throughput computing. The principles and techniques that underlie the Open Science Grid can also be applied to Campus Grids since many of the requirements are the same, even if the implementation technologies differ. We find five requirements for a campus grid: trust relationships, job submission, resource independence, accounting, and data management. The Holland Computing Center's campus grid at the University of Nebraska-Lincoln was designed to fulfill the requirements of a campus grid. A bridging daemon was designed to bring non-Condor clusters into a grid managed by Condor. Condor features which make it possible to bridge Condor sites into a multi-campus grid have been exploited at the Holland Computing Center as well.

  14. Assessment of grid optimisation measures for the German transmission grid using open source grid data

    Science.gov (United States)

    Böing, F.; Murmann, A.; Pellinger, C.; Bruckmeier, A.; Kern, T.; Mongin, T.

    2018-02-01

    The expansion of capacities in the German transmission grid is a necessity for further integration of renewable energy sources into the electricity sector. In this paper, the grid optimisation measures ‘Overhead Line Monitoring’, ‘Power-to-Heat’ and ‘Demand Response in the Industry’ are evaluated and compared against conventional grid expansion for the year 2030. Initially, the methodical approach of the simulation model is presented and detailed descriptions of the grid model and the used grid data, which partly originates from open-source platforms, are provided. Further, this paper explains how ‘Curtailment’ and ‘Redispatch’ can be reduced by implementing grid optimisation measures and how the depreciation of economic costs can be determined considering construction costs. The developed simulations show that the conventional grid expansion is more efficient and implies more grid relieving effects than the evaluated grid optimisation measures.

  15. Utah Bouguer Gravity Grid

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — A 2.5 kilometer Bouguer anomaly grid for the state of Utah. Number of columns is 196 and number of rows is 245. The order of the data is from the lower left to the...

  16. Modelling Chinese Smart Grid

    DEFF Research Database (Denmark)

    Yuksel, Ender; Nielson, Hanne Riis; Nielson, Flemming

    In this document, we consider a specific Chinese Smart Grid implementation and try to address the verification problem for certain quantitative properties including performance and battery consumption. We employ stochastic model checking approach and present our modelling and analysis study using...

  17. Grid attacks avian flu

    CERN Multimedia

    2006-01-01

    During April, a collaboration of Asian and European laboratories analysed 300,000 possible drug components against the avian flu virus H5N1 using the EGEE Grid infrastructure. Schematic presentation of the avian flu virus.The distribution of the EGEE sites in the world on which the avian flu scan was performed. The goal was to find potential compounds that can inhibit the activities of an enzyme on the surface of the influenza virus, the so-called neuraminidase, subtype N1. Using the Grid to identify the most promising leads for biological tests could speed up the development process for drugs against the influenza virus. Co-ordinated by CERN and funded by the European Commission, the EGEE project (Enabling Grids for E-sciencE) aims to set up a worldwide grid infrastructure for science. The challenge of the in silico drug discovery application is to identify those molecules which can dock on the active sites of the virus in order to inhibit its action. To study the impact of small scale mutations on drug r...

  18. Multi-Grid Lanczos

    Science.gov (United States)

    Clark, M. A.; Jung, Chulwoo; Lehner, Christoph

    2018-03-01

    We present a Lanczos algorithm utilizing multiple grids that reduces the memory requirements both on disk and in working memory by one order of magnitude for RBC/UKQCD's 48I and 64I ensembles at the physical pion mass. The precision of the resulting eigenvectors is on par with exact deflation.

  19. Multi-Grid Lanczos

    Directory of Open Access Journals (Sweden)

    Clark M. A.

    2018-01-01

    Full Text Available We present a Lanczos algorithm utilizing multiple grids that reduces the memory requirements both on disk and in working memory by one order of magnitude for RBC/UKQCD’s 48I and 64I ensembles at the physical pion mass. The precision of the resulting eigenvectors is on par with exact deflation.

  20. Nevada Isostatic Gravity Grid

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — A 2 kilometer Isostatic anomaly grid for the state of Nevada. Number of columns is 269 and number of rows is 394. The order of the data is from the lower left to the...

  1. Steering the Smart Grid

    NARCIS (Netherlands)

    Molderink, Albert; Bakker, Vincent; Bosman, M.G.C.; Hurink, Johann L.; Smit, Gerardus Johannes Maria

    2010-01-01

    Increasing energy prices and the greenhouse effect lead to more awareness of energy efficiency of electricity supply. During the last years, a lot of technologies and optimization methodologies were developed to increase the efficiency, maintain the grid stability and support large scale

  2. Cutback for grid operators

    International Nuclear Information System (INIS)

    Meulmeester, P.; De Laat, J.

    2006-01-01

    The Netherlands Competition Authority (NMa), in which the Office of Energy Regulation (DTe) is included plan to decrease the capital cost compensation (or weighted average cost of capital or WACC) for grid operators. In this article it is explained how the compensation is calculated, why this measure will be taken and what the effects of this cutback are [nl

  3. Autonomous Energy Grids: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Kroposki, Benjamin D [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Dall-Anese, Emiliano [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Bernstein, Andrey [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Zhang, Yingchen [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Hodge, Brian S [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

    2017-10-04

    With much higher levels of distributed energy resources - variable generation, energy storage, and controllable loads just to mention a few - being deployed into power systems, the data deluge from pervasive metering of energy grids, and the shaping of multi-level ancillary-service markets, current frameworks to monitoring, controlling, and optimizing large-scale energy systems are becoming increasingly inadequate. This position paper outlines the concept of 'Autonomous Energy Grids' (AEGs) - systems that are supported by a scalable, reconfigurable, and self-organizing information and control infrastructure, can be extremely secure and resilient (self-healing), and self-optimize themselves in real-time for economic and reliable performance while systematically integrating energy in all forms. AEGs rely on scalable, self-configuring cellular building blocks that ensure that each 'cell' can self-optimize when isolated from a larger grid as well as partaking in the optimal operation of a larger grid when interconnected. To realize this vision, this paper describes the concepts and key research directions in the broad domains of optimization theory, control theory, big-data analytics, and complex system modeling that will be necessary to realize the AEG vision.

  4. Bolivian Bouguer Anomaly Grid

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — A 1 kilometer Bouguer anomaly grid for the country of Bolivia.Number of columns is 550 and number of rows is 900. The order of the data is from the lower left to the...

  5. Smart grid voor comfort

    NARCIS (Netherlands)

    Zeiler, W.; Vissers, D.R.; Maaijen, H.N.; Kling, W.L.; Velden, van der J.A.J.; Larsen, J.P.

    2012-01-01

    Er vindt onderzoek plaats naar een nieuwe regelstrategie gebaseerd op de toepassing van een draadloos sensor netwerk dat is gekoppeld aan het smart grid. Doel van deze regelstrategie is om op gebruikersniveau energie te kunnen besparen met behoud of zelfs verbetering van het individueel comfort. Er

  6. Kids Enjoy Grids

    CERN Multimedia

    2007-01-01

    I want to come back and work here when I'm older,' was the spontaneous reaction of one of the children invited to CERN by the Enabling Grids for E-sciencE project for a 'Grids for Kids' day at the end of January. The EGEE project is led by CERN, and the EGEE gender action team organized the day to introduce children to grid technology at an early age. The school group included both boys and girls, aged 9 to 11. All of the presenters were women. 'In general, before this visit, the children thought that scientists always wore white coats and were usually male, with wild Einstein-like hair,' said Jackie Beaver, the class's teacher at the Institut International de Lancy, a school near Geneva. 'They were surprised and pleased to see that women became scientists, and that scientists were quite 'normal'.' The half-day event included presentations about why Grids are needed, a visit of the computer centre, some online games, and plenty of time for questions. In the end, everyone agreed that it was a big success a...

  7. Reconsidering solar grid parity

    International Nuclear Information System (INIS)

    Yang, C.-J.

    2010-01-01

    Grid parity-reducing the cost of solar energy to be competitive with conventional grid-supplied electricity-has long been hailed as the tipping point for solar dominance in the energy mix. Such expectations are likely to be overly optimistic. A realistic examination of grid parity suggests that the cost-effectiveness of distributed photovoltaic (PV) systems may be further away than many are hoping for. Furthermore, cost-effectiveness may not guarantee commercial competitiveness. Solar hot water technology is currently far more cost-effective than photovoltaic technology and has already reached grid parity in many places. Nevertheless, the market penetration of solar water heaters remains limited for reasons including unfamiliarity with the technologies and high upfront costs. These same barriers will likely hinder the adoption of distributed solar photovoltaic systems as well. The rapid growth in PV deployment in recent years is largely policy-driven and such rapid growth would not be sustainable unless governments continue to expand financial incentives and policy mandates, as well as address regulatory and market barriers.

  8. Maine Bouguer Gravity Grid

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — A 2 kilometer Bouguer anomaly grid for the state of Maine. Number of columns is 197 and number of rows is 292. The order of the data is from the lower left to the...

  9. Minnesota Bouguer Anomaly Grid

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — A 1.5 kilometer Bouguer anomaly grid for the state of Minnesota. Number of columns is 404 and number of rows is 463. The order of the data is from the lower left to...

  10. Molecular Grid Membranes

    National Research Council Canada - National Science Library

    Michl, Josef; Magnera, Thomas

    2008-01-01

    ...) porphyrin triply linked in the meso-meso, and both beta-beta positions four times by carbon-carbon bonds to each of its neighbors to form porphite sheets a grid-type material that would be an analog of graphene...

  11. The Grid challenge

    CERN Multimedia

    Lundquest, E

    2003-01-01

    At a customer panel discussion during OracleWorld in San Franciso, grid computing was being pushed as the next big thing - even if panellists couldsn't quite agree on what it is, what it will cost or when it will appear (1 page).

  12. NSTAR Smart Grid Pilot

    Energy Technology Data Exchange (ETDEWEB)

    Rabari, Anil [NSTAR Electric, Manchester, NH (United States); Fadipe, Oloruntomi [NSTAR Electric, Manchester, NH (United States)

    2014-03-31

    NSTAR Electric & Gas Corporation (“the Company”, or “NSTAR”) developed and implemented a Smart Grid pilot program beginning in 2010 to demonstrate the viability of leveraging existing automated meter reading (“AMR”) deployments to provide much of the Smart Grid functionality of advanced metering infrastructure (“AMI”), but without the large capital investment that AMI rollouts typically entail. In particular, a central objective of the Smart Energy Pilot was to enable residential dynamic pricing (time-of-use “TOU” and critical peak rates and rebates) and two-way direct load control (“DLC”) by continually capturing AMR meter data transmissions and communicating through customer-sited broadband connections in conjunction with a standardsbased home area network (“HAN”). The pilot was supported by the U.S. Department of Energy’s (“DOE”) through the Smart Grid Demonstration program. NSTAR was very pleased to not only receive the funding support from DOE, but the guidance and support of the DOE throughout the pilot. NSTAR is also pleased to report to the DOE that it was able to execute and deliver a successful pilot on time and on budget. NSTAR looks for future opportunities to work with the DOE and others in future smart grid projects.

  13. Controlling smart grid adaptivity

    OpenAIRE

    Toersche, Hermen; Nykamp, Stefan; Molderink, Albert; Hurink, Johann L.; Smit, Gerardus Johannes Maria

    2012-01-01

    Methods are discussed for planning oriented smart grid control to cope with scenarios with limited predictability, supporting an increasing penetration of stochastic renewable resources. The performance of these methods is evaluated with simulations using measured wind generation and consumption data. Forecast errors are shown to affect worst case behavior in particular, the severity of which depends on the chosen adaptivity strategy and error model.

  14. The surveillance error grid.

    Science.gov (United States)

    Klonoff, David C; Lias, Courtney; Vigersky, Robert; Clarke, William; Parkes, Joan Lee; Sacks, David B; Kirkman, M Sue; Kovatchev, Boris

    2014-07-01

    Currently used error grids for assessing clinical accuracy of blood glucose monitors are based on out-of-date medical practices. Error grids have not been widely embraced by regulatory agencies for clearance of monitors, but this type of tool could be useful for surveillance of the performance of cleared products. Diabetes Technology Society together with representatives from the Food and Drug Administration, the American Diabetes Association, the Endocrine Society, and the Association for the Advancement of Medical Instrumentation, and representatives of academia, industry, and government, have developed a new error grid, called the surveillance error grid (SEG) as a tool to assess the degree of clinical risk from inaccurate blood glucose (BG) monitors. A total of 206 diabetes clinicians were surveyed about the clinical risk of errors of measured BG levels by a monitor. The impact of such errors on 4 patient scenarios was surveyed. Each monitor/reference data pair was scored and color-coded on a graph per its average risk rating. Using modeled data representative of the accuracy of contemporary meters, the relationships between clinical risk and monitor error were calculated for the Clarke error grid (CEG), Parkes error grid (PEG), and SEG. SEG action boundaries were consistent across scenarios, regardless of whether the patient was type 1 or type 2 or using insulin or not. No significant differences were noted between responses of adult/pediatric or 4 types of clinicians. Although small specific differences in risk boundaries between US and non-US clinicians were noted, the panel felt they did not justify separate grids for these 2 types of clinicians. The data points of the SEG were classified in 15 zones according to their assigned level of risk, which allowed for comparisons with the classic CEG and PEG. Modeled glucose monitor data with realistic self-monitoring of blood glucose errors derived from meter testing experiments plotted on the SEG when compared to

  15. AQUAGRID: The subsurface hydrology Grid service of the Sardinian regional Grid infrastructure

    International Nuclear Information System (INIS)

    Lecca, G.; Murgia, F.; Maggi, P.; Perias, A.

    2007-01-01

    AQUAGRID is the subsurface hydrology service of the Sardinian regional Grid infrastructure, designed to deliver complex environmental applications via a user-friendly Web portal. The service is oriented towards the needs of water professionals providing them a flexible and powerful tool to solve water resources management problems and aid decision between different remediation options for contaminated soil and groundwater. In this paper, the AQUAGRID application concept and the enabling technologies are illustrated. The heart of the service is the CODESA-3D hydrogeological model to simulate complex and large groundwater flow and contaminant transport problems. The relevant experience gained from the porting of the CODESA-3D application on the EGEE infrastructure, via the GILDA test bed (https://gilda.ct.infn.it), has contributed to the service prototype. AQUAGRID is built on top of compute-Grid technologies by means of the EnginFrame Grid portal. The portal enables the interaction with the underlying Grid infrastructure and manages the computational requirements of the whole application system. Data management, distribution and visualization mechanisms are based on the tools provided by the DatacroSSing Decision Support System (http://datacrossing.crs4.it). The DSS, built on top of the SRB data-Grid middleware, is based on Web-GIS and relational database technologies. The resulting production environment allows the end-user to visualize and interact with the results of the performed analyses, using graphs, annotated maps and 3D objects. Such a set of graphical widgets increases enormously the number of AQUAGRID potential users because it does not require any specific expertise of the physical model and technological background to be understood. (Author)

  16. Grid interoperability: the interoperations cookbook

    Energy Technology Data Exchange (ETDEWEB)

    Field, L; Schulz, M [CERN (Switzerland)], E-mail: Laurence.Field@cern.ch, E-mail: Markus.Schulz@cern.ch

    2008-07-01

    Over recent years a number of grid projects have emerged which have built grid infrastructures that are now the computing backbones for various user communities. A significant number of these communities are limited to one grid infrastructure due to the different middleware and procedures used in each grid. Grid interoperation is trying to bridge these differences and enable virtual organizations to access resources independent of the grid project affiliation. This paper gives an overview of grid interoperation and describes the current methods used to bridge the differences between grids. Actual use cases encountered during the last three years are discussed and the most important interfaces required for interoperability are highlighted. A summary of the standardisation efforts in these areas is given and we argue for moving more aggressively towards standards.

  17. Grid interoperability: the interoperations cookbook

    International Nuclear Information System (INIS)

    Field, L; Schulz, M

    2008-01-01

    Over recent years a number of grid projects have emerged which have built grid infrastructures that are now the computing backbones for various user communities. A significant number of these communities are limited to one grid infrastructure due to the different middleware and procedures used in each grid. Grid interoperation is trying to bridge these differences and enable virtual organizations to access resources independent of the grid project affiliation. This paper gives an overview of grid interoperation and describes the current methods used to bridge the differences between grids. Actual use cases encountered during the last three years are discussed and the most important interfaces required for interoperability are highlighted. A summary of the standardisation efforts in these areas is given and we argue for moving more aggressively towards standards

  18. Allegheny County Map Index Grid

    Data.gov (United States)

    Allegheny County / City of Pittsburgh / Western PA Regional Data Center — Map Index Sheets from Block and Lot Grid of Property Assessment and based on aerial photography, showing 1983 datum with solid line and NAD 27 with 5 second grid...

  19. GridCom, Grid Commander: graphical interface for Grid jobs and data management; GridCom, Grid Commander: graficheskij interfejs dlya raboty s zadachami i dannymi v gride

    Energy Technology Data Exchange (ETDEWEB)

    Galaktionov, V V

    2011-07-01

    GridCom - the software package for maintenance of automation of access to means of distributed system Grid (jobs and data). The client part, executed in the form of Java-applets, realises the Web-interface access to Grid through standard browsers. The executive part Lexor (LCG Executor) is started by the user in UI (User Interface) machine providing performance of Grid operations

  20. Standardization in smart grids. Introduction to IT-related methodologies, architectures and standards

    Energy Technology Data Exchange (ETDEWEB)

    Uslar, Mathias; Specht, Michael; Daenekas, Christian; Trefke, Joern; Rohjans, Sebastian; Gonzalez, Jose M.; Rosinger, Christine; Bleiker, Robert [OFFIS - Institut fuer Informatik, Oldenburg (Germany)

    2013-03-01

    Introduction to Standardization for Smart Grids. Presents a tutorial and best practice of Smart Grid Prototype Projects. Written by leading experts in the field. Besides the regulatory and market aspects, the technical level dealing with the knowledge from multiple disciplines and the aspects of technical system integration to achieve interoperability and integration has been a strong focus in the Smart Grid. This topic is typically covered by the means of using (technical) standards for processes, data models, functions and communication links. Standardization is a key issue for Smart Grids due to the involvement of many different sectors along the value chain from the generation to the appliances. The scope of Smart Grid is broad, therefore, the standards landscape is unfortunately very large and complex. This is why the three European Standards Organizations ETSI, CEN and CENELEC created a so called Joint Working Group (JWG). This was the first harmonized effort in Europe to bring together the needed disciplines and experts delivering the final report in May 2011. After this approach proved useful, the Commission used the Mandate M/490: Standardization Mandate to European Standardization Organizations (ESOs) to support European Smart Grid deployment. The focal point addressing the ESO's response to M/490 will be the CEN, CENELEC and ETSI Smart Grids Coordination Group (SG-CG). Based on this mandate, meaningful standardization of architectures, use cases, communication technologies, data models and security standards takes place in the four existing working groups. This book provides an overview on the various building blocks and standards identified as the most prominent ones by the JWG report as well as by the first set of standards group - IEC 61850 and CIM, IEC PAS 62559 for documenting Smart Grid use cases, security requirements from the SGIS groups and an introduction on how to apply the Smart Grid Architecture Model SGAM for utilities. In addition

  1. Current Grid operation and future role of the Grid

    Science.gov (United States)

    Smirnova, O.

    2012-12-01

    Grid-like technologies and approaches became an integral part of HEP experiments. Some other scientific communities also use similar technologies for data-intensive computations. The distinct feature of Grid computing is the ability to federate heterogeneous resources of different ownership into a seamless infrastructure, accessible via a single log-on. Like other infrastructures of similar nature, Grid functioning requires not only technologically sound basis, but also reliable operation procedures, monitoring and accounting. The two aspects, technological and operational, are closely related: weaker is the technology, more burden is on operations, and other way around. As of today, Grid technologies are still evolving: at CERN alone, every LHC experiment uses an own Grid-like system. This inevitably creates a heavy load on operations. Infrastructure maintenance, monitoring and incident response are done on several levels, from local system administrators to large international organisations, involving massive human effort worldwide. The necessity to commit substantial resources is one of the obstacles faced by smaller research communities when moving computing to the Grid. Moreover, most current Grid solutions were developed under significant influence of HEP use cases, and thus need additional effort to adapt them to other applications. Reluctance of many non-HEP researchers to use Grid negatively affects the outlook for national Grid organisations, which strive to provide multi-science services. We started from the situation where Grid organisations were fused with HEP laboratories and national HEP research programmes; we hope to move towards the world where Grid will ultimately reach the status of generic public computing and storage service provider and permanent national and international Grid infrastructures will be established. How far will we be able to advance along this path, depends on us. If no standardisation and convergence efforts will take place

  2. Current Grid operation and future role of the Grid

    International Nuclear Information System (INIS)

    Smirnova, O

    2012-01-01

    Grid-like technologies and approaches became an integral part of HEP experiments. Some other scientific communities also use similar technologies for data-intensive computations. The distinct feature of Grid computing is the ability to federate heterogeneous resources of different ownership into a seamless infrastructure, accessible via a single log-on. Like other infrastructures of similar nature, Grid functioning requires not only technologically sound basis, but also reliable operation procedures, monitoring and accounting. The two aspects, technological and operational, are closely related: weaker is the technology, more burden is on operations, and other way around. As of today, Grid technologies are still evolving: at CERN alone, every LHC experiment uses an own Grid-like system. This inevitably creates a heavy load on operations. Infrastructure maintenance, monitoring and incident response are done on several levels, from local system administrators to large international organisations, involving massive human effort worldwide. The necessity to commit substantial resources is one of the obstacles faced by smaller research communities when moving computing to the Grid. Moreover, most current Grid solutions were developed under significant influence of HEP use cases, and thus need additional effort to adapt them to other applications. Reluctance of many non-HEP researchers to use Grid negatively affects the outlook for national Grid organisations, which strive to provide multi-science services. We started from the situation where Grid organisations were fused with HEP laboratories and national HEP research programmes; we hope to move towards the world where Grid will ultimately reach the status of generic public computing and storage service provider and permanent national and international Grid infrastructures will be established. How far will we be able to advance along this path, depends on us. If no standardisation and convergence efforts will take place

  3. How to Make Financial Aid "Freshman-Friendly"

    Science.gov (United States)

    Pugh, Susan L.; Johnson, David B.

    2011-01-01

    Ultimately, making financial aid "freshman friendly" also makes financial aid "sophomore friendly," "junior friendly," and "senior friendly." Indiana University has in place an Office of Enrollment Management (OEM) model that includes focused financial aid packaging strategies complemented by unique contact…

  4. Communication technologies in smart grid

    Directory of Open Access Journals (Sweden)

    Miladinović Nikola

    2013-01-01

    Full Text Available The role of communication technologies in Smart Grid lies in integration of large number of devices into one telecommunication system. This paper provides an overview of the technologies currently in use in electric power grid, that are not necessarily in compliance with the Smart Grid concept. Considering that the Smart Grid is open to the flow of information in all directions, it is necessary to provide reliability, protection and security of information.

  5. Class III camouflage using skeletal anchorage and Pendex appliance.

    Science.gov (United States)

    Miguel, José Augusto M; Zanardi, Gustavo

    2011-01-01

    This case report describes the orthodontic treatment for a young female, aged 18 years 4 months, with a Class III malocclusion on the right side, with a combination of a posterior and anterior crossbite. Two rigid orthodontic mini-implants were placed in the retromolar region in order to move the entire lower arch distally with nickel-titanium coil springs. In addition, a Pendex appliance was used to create space and to improve the arch form and the transverse relationship. The active treatment period was 17 months. Normal overjet and overbite were obtained, and facial balance was improved. Although the cephalometric superimposition has demonstrated the effects of dental compensation, the final dental and facial results were satisfactory and stable after the second year in retention. Copyright © 2011 Società Italiana di Ortodonzia SIDO. Published by Elsevier Srl. All rights reserved.

  6. Solar water heating: The making of a simple, standard appliance

    International Nuclear Information System (INIS)

    Block, D.L.

    1993-01-01

    Within the solar community we have carried on never-ending discussions about the performance of solar water heaters. As a long-time solar advocate and researcher, I am continually asked, open-quotes When will solar usage become widespread?close quotes We who are in the solar business all face this question, and we must respond. Our answers usually take the form of some discussion on efficiency improvements, life-cycle costs, level playing field or environmental factors. But the only real way to answer this question is: Use of solar will be widewspread when a solar water heater is considered to be just another standard appliance. Increased installations is the key, and the solar technology with the greatest near-term potential for increased installation is solar water heating

  7. Inventory of usage pattern for wood burning appliances

    International Nuclear Information System (INIS)

    Cooper, David; Joeborn, Inger; Sjoedin, Aake; Munkhammar, Inger; Gustavsson, Lennart

    2005-02-01

    The Swedish Environmental Research Institute (IVL) in co-operation with the Swedish National Testing and Research Institute (SP) and Statistics Sweden (SCB) have investigated the use of domestic wood burning for wood stoves and open fireplaces. The results from a closer examination of existing national energy statistics for residential heating has enabled a division of the average consumption of firewood for each house by the category 'fireplace for open fire' and 'tiled stove/heating stove/fireplace for wood'. The estimation of emissions can therefore be improved by differentiating emission factors for different wood stoves and open fireplaces. Today, only one emission factor is used. An insight into general firing procedures, wood storage routines etc. was investigated using a questionnaire for the Teleborg area of the city Vaexjoe. The results of this study provide a foundation for further work, which will subsequently enable improvements for emission inventories on small-scale biomass combustion from household appliances

  8. Contextual Mobile Learning: A Step Further to Mastering Professional Appliances

    Directory of Open Access Journals (Sweden)

    René Chalon

    2007-10-01

    Full Text Available In this paper we describe our approach whose objective is to apply MOCOCO concepts to e-learning. After a short presentation of MOCOCO (Mobility, Cooperation, Contextualization and IMERA (Mobile Interaction in the Augmented Real Environment principles we will discuss their use in a project called HMTD (Help Me To Do whose aim is to use wearable computer for a framework of activities of better use, maintenance and repairing of professional appliances. We will successively describe m-learning scope, contextualization and cooperation advantages as well as learning methods. A case study of configuration of wearable computer and its peripherals, taking into account context, in-situ storage, traceability and regulation in these activities finishes this paper.

  9. Magnetic emission ranking of electrical appliances. A comprehensive market survey

    International Nuclear Information System (INIS)

    Leitgeb, N.; Cech, R.; Schroettner, J.; Lehofer, P.; Schmidpeter, U.; Rampetsreiter, M.

    2008-01-01

    Over the last decades emissions of magnetic fields from electric appliances have considerably changed. Based on a comprehensive market survey it could be shown that today magnetic emissions are usually characterised by complex frequency spectra while single-frequency emissions have become rare. Therefore, spectral assessment procedures play a critical role. Compared to frequency-weighted equivalent magnetic induction, rms values may underestimate emissions up to two orders of magnitudes. Therefore, rms measurements are not suitable and emission-ranking lists of devices need revision. Surface hot-spot measurements at nominal load conditions and 230 V/50 Hz supply involved 1146 new electrical devices of 166 different categories. High emissions were not rare. Magnetic emissions of devices of 73 different categories exceeded reference levels up to almost two orders of magnitudes above reference levels. Maximum values were higher than reported so far. Magnetic emissions were high enough to make even conformity with existing basic restrictions not self-evident. (authors)

  10. A cephalometric comparison of treatment with the Twin-block and stainless steel crown Herbst appliances followed by fixed appliance therapy.

    Science.gov (United States)

    Schaefer, Abbie T; McNamara, James A; Franchi, Lorenzo; Baccetti, Tiziano

    2004-07-01

    This study compared the effects of 2 treatment protocols for correcting Class II disharmony. The first phase of treatment consisted of functional jaw orthopedics with either the Twin-block or the stainless-steel crown Herbst appliance; the second phase consisted of comprehensive fixed-appliance therapy in both protocols. Each of the 2 samples comprised 28 consecutively treated Class II patients. The mean age at the start of treatment was approximately 12 years, and the mean age at the end of the treatment was approximately 14.5 years in both groups. The duration of the treatment phase with the functional appliance was approximately 13 months, and the duration of fixed-appliance therapy was approximately 15 months in both groups. The sex distribution was identical in the 2 groups. Lateral cephalograms were analyzed at the start of treatment (T1) and at the end of the overall treatment protocol (T2). Nonparametric statistics were used for comparisons of starting forms and of the T1-T2 changes between the 2 treatment groups. The stainless-steel crown Herbst appliance and the Twin-block appliance produced very similar therapeutic modifications in Class II patients, although the Twin-block group exhibited almost 2 mm greater correction of the maxillomandibular differential than did the crown Herbst group. The treatment effects of both protocols led to a normalization of the dentoskeletal parameters at the end of the overall treatment period. Twin-block therapy also induced a greater increase in the height of the mandibular ramus (posterior facial height). Overall, only minor differences were detected in the treatment and posttreatment effects of a compliance-free (crown Herbst) and a noncompliance-free (Twin-block) appliance for correcting Class II disharmony.

  11. Grid3: An Application Grid Laboratory for Science

    CERN Multimedia

    CERN. Geneva

    2004-01-01

    level services required by the participating experiments. The deployed infrastructure has been operating since November 2003 with 27 sites, a peak of 2800 processors, work loads from 10 different applications exceeding 1300 simultaneous jobs, and data transfers among sites of greater than 2 TB/day. The Grid3 infrastructure was deployed from grid level services provided by groups and applications within the collaboration. The services were organized into four distinct "grid level services" including: Grid3 Packaging, Monitoring and Information systems, User Authentication and the iGOC Grid Operatio...

  12. Grid Integration | Water Power | NREL

    Science.gov (United States)

    Grid Integration Grid Integration For marine and hydrokinetic technologies to play a larger role in supplying the nation's energy needs, integration into the U.S. power grid is an important challenge to address. Efficient integration of variable power resources like water power is a critical part of the

  13. What is a smart grid?

    NARCIS (Netherlands)

    Kumar, A.

    2017-01-01

    The Indian Smart Grid Forum defines a smart grid as "a power system capable of two-way communication between all the entities of the network-generation, transmission, distribution and the consumers". Like most work on smart grids, this view is also mainly technical. This paper aims to progress the

  14. Pyramid solar micro-grid

    Science.gov (United States)

    Huang, Bin-Juine; Hsu, Po-Chien; Wang, Yi-Hung; Tang, Tzu-Chiao; Wang, Jia-Wei; Dong, Xin-Hong; Hsu, Hsin-Yi; Li, Kang; Lee, Kung-Yen

    2018-03-01

    A novel pyramid solar micro-grid is proposed in the present study. All the members within the micro-grid can mutually share excess solar PV power each other through a binary-connection hierarchy. The test results of a 2+2 pyramid solar micro-grid consisting of 4 individual solar PV systems for self-consumption are reported.

  15. Survival of palatal miniscrews used for orthodontic appliance anchorage: a retrospective cohort study.

    Science.gov (United States)

    Karagkiolidou, Angeliki; Ludwig, Björn; Pazera, Pawel; Gkantidis, Nikolaos; Pandis, Nikolaos; Katsaros, Christos

    2013-06-01

    The purpose of this study was to examine the overall success of miniscrews inserted in the paramedian palatal region for support of various appliances during orthodontic treatment. The patients received 1 or 2 miniscrews in the paramedian anterior palate of 8.0-mm length and 1.6-mm diameter placed during orthodontic treatment by the same experienced orthodontist. In total, 196 patients (121 girls, 75 boys; median age, 11.7; interquartile range, 3.7) who received 384 miniscrews were evaluated. Two hundred four miniscrews were used with rapid palatal expansion appliances, 136 with appliances for distalization of posterior teeth, and 44 with other appliances, such as transpalatal arches for tooth stabilization. The overall survival of the miniscrews was excellent (97.9%) in the cases examined. Cox regression analysis showed no difference in the overall survival rates of miniscrews loaded with different appliances for sex (hazard ratio, 0.95; 95% confidence interval, 0.71-1.27; P = 0.73) after adjusting for appliance and age. This study shows that miniscrews placed in the paramedian anterior palate for supporting various orthodontic appliances have excellent survival. Copyright © 2013 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

  16. Effect of thermoplastic appliance thickness on initial stress distribution in periodontal ligament

    Directory of Open Access Journals (Sweden)

    De-Shin Liu

    2015-04-01

    Full Text Available A numerical investigation into the initial stress distribution induced within the periodontal ligament by thermoplastic appliances with different thicknesses is performed. Based on the plaster model of a 25-year-old male patient, a finite element model of the maxillary lateral incisors and their supporting structures is constructed. In addition, four finite element models of thermoplastic appliances with different thicknesses in the range of 0.5–1.25 mm are also constructed based on the same plaster model. Finite element analysis simulations are performed to examine the effects of the force delivered by the thermoplastic appliances on the stress response of the periodontal ligament during the elastic recovery process. The results show that the stress induced in the periodontal ligament increases with an increasing appliance thickness. For example, the stress triples from 0.0012 to 0.0038 MPa as the appliance thickness is increased from 0.75 to 1.25 mm. The results presented in this study provide a useful insight into as a result of the compressive and tensile stresses induced by thermoplastic appliances of different thicknesses. Moreover, the results enable the periodontal ligament stress levels produced by thermoplastic appliances of different thicknesses to be reliably estimated.

  17. Design and manufacturing of patient-specific orthodontic appliances by computer-aided engineering techniques.

    Science.gov (United States)

    Barone, Sandro; Neri, Paolo; Paoli, Alessandro; Razionale, Armando Viviano

    2018-01-01

    Orthodontic treatments are usually performed using fixed brackets or removable oral appliances, which are traditionally made from alginate impressions and wax registrations. Among removable devices, eruption guidance appliances are used for early orthodontic treatments in order to intercept and prevent malocclusion problems. Commercially available eruption guidance appliances, however, are symmetric devices produced using a few standard sizes. For this reason, they are not able to meet all the specific patient's needs since the actual dental anatomies present various geometries and asymmetric conditions. In this article, a computer-aided design-based methodology for the design and manufacturing of a patient-specific eruption guidance appliances is presented. The proposed approach is based on the digitalization of several steps of the overall process: from the digital reconstruction of patients' anatomies to the manufacturing of customized appliances. A finite element model has been developed to evaluate the temporomandibular joint disks stress level caused by using symmetric eruption guidance appliances with different teeth misalignment conditions. The developed model can then be used to guide the design of a patient-specific appliance with the aim at reducing the patient discomfort. At this purpose, two different customization levels are proposed in order to face both arches and single tooth misalignment issues. A low-cost manufacturing process, based on an additive manufacturing technique, is finally presented and discussed.

  18. Treatment effects of the Jasper Jumper and the Bionator associated with fixed appliances.

    Science.gov (United States)

    Neves, Leniana Santos; Janson, Guilherme; Cançado, Rodrigo Hermont; de Lima, Karina Jerônimo Rodrigues Santiago; Fernandes, Thaís Maria Freire; Henriques, José Fernando Castanha

    2014-01-01

    The aim of this study was to evaluate the effects of Class II malocclusion treatment with the Jasper Jumper and the Bionator, associated with fixed appliances. The sample comprised 77 young individuals divided into 3 groups: Group 1 consisted of 25 patients treated with the Jasper Jumper appliance associated with fixed appliances for a mean period of 2.15 years; group 2 had 30 patients, treated with the Bionator and fixed appliances, for a mean treatment time of 3.92 years; and the control group included 22 subjects followed for a mean period of 2.13 years. The initial and final lateral cephalograms of the patients were evaluated. Intergroup comparison at the initial stage and of the treatment changes were performed by analysis of variance. Their effects consisted in a restrictive effect on the maxilla, a slight increase in anterior face height, retrusion and extrusion of the maxillary incisors, labial tipping and protrusion of the mandibular incisors in both groups and intrusion with the Jasper Jumper appliance, maxillary molar distalization with the Jasper Jumper, extrusion and mesialization of the mandibular molars, both appliances provided significant improvement of the maxillomandibular relationship, overjet, overbite and molar relationship. The effects of both appliances in class II malocclusion treatment are similar; however, treatment with the Jasper Jumper was shorter than with the Bionator.

  19. MICROARRAY IMAGE GRIDDING USING GRID LINE REFINEMENT TECHNIQUE

    Directory of Open Access Journals (Sweden)

    V.G. Biju

    2015-05-01

    Full Text Available An important stage in microarray image analysis is gridding. Microarray image gridding is done to locate sub arrays in a microarray image and find co-ordinates of spots within each sub array. For accurate identification of spots, most of the proposed gridding methods require human intervention. In this paper a fully automatic gridding method which enhances spot intensity in the preprocessing step as per a histogram based threshold method is used. The gridding step finds co-ordinates of spots from horizontal and vertical profile of the image. To correct errors due to the grid line placement, a grid line refinement technique is proposed. The algorithm is applied on different image databases and results are compared based on spot detection accuracy and time. An average spot detection accuracy of 95.06% depicts the proposed method’s flexibility and accuracy in finding the spot co-ordinates for different database images.

  20. A comparison of pain experienced by patients treated with labial and lingual orthodontic appliances.

    Science.gov (United States)

    Wu, Abby K Y; McGrath, Colman; Wong, Ricky W K; Wiechmann, D; Rabie, A Bakr M

    2010-08-01

    The aim of this prospective longitudinal study was to compare pain experiences among Chinese adult patients treated with labial and lingual orthodontic appliances. Sixty patients, 30 with labial appliances (18 females and 12 males, mean age 20.33 years, SD +/- 4.205) and 30 with lingual appliances (22 females and 8 males, mean age 21.63 years, SD +/- 2.236), rated their overall pain experience on a 100 mm visual analogue scale (VAS) at three time points: 1 week (T(1)), 1 month (T(2)), and 3 months (T(3)) after bracket placement. In addition, on a separate 100 mm VAS, they rated their pain experience at the locations of the tongue, lips, cheeks, gums, face, and jaw at T(1), T(2), and T(3). Changes in pain VAS were conducted using Friedman analysis of variance, area under the curve (AUC) analysis and the data were compared using a t-test. There was no significant difference in global ratings of pain among those treated with labial or lingual appliances (P > 0.05). Among both groups, global ratings of pain decreased over the study period (P appliances reported higher ratings of tongue pain (P appliances reported higher ratings of lip (P appliances rate similarly the level of overall pain they experience during treatment. Ratings of overall pain experienced decreased for both treatment groups with time. However, ratings of pain differed at various sites with respect to the type of orthodontic appliance. These findings have implications in informing patients' treatment decision-making processes regarding labial and lingual appliances and in the management of discomfort associated with different treatment modalities.

  1. Smart Grid Demonstration Project

    Energy Technology Data Exchange (ETDEWEB)

    Miller, Craig [National Rural Electric Cooperative Association, Arlington, VA (United States); Carroll, Paul [National Rural Electric Cooperative Association, Arlington, VA (United States); Bell, Abigail [National Rural Electric Cooperative Association, Arlington, VA (United States)

    2015-03-11

    The National Rural Electric Cooperative Association (NRECA) organized the NRECA-U.S. Department of Energy (DOE) Smart Grid Demonstration Project (DE-OE0000222) to install and study a broad range of advanced smart grid technologies in a demonstration that spanned 23 electric cooperatives in 12 states. More than 205,444 pieces of electronic equipment and more than 100,000 minor items (bracket, labels, mounting hardware, fiber optic cable, etc.) were installed to upgrade and enhance the efficiency, reliability, and resiliency of the power networks at the participating co-ops. The objective of this project was to build a path for other electric utilities, and particularly electrical cooperatives, to adopt emerging smart grid technology when it can improve utility operations, thus advancing the co-ops’ familiarity and comfort with such technology. Specifically, the project executed multiple subprojects employing a range of emerging smart grid technologies to test their cost-effectiveness and, where the technology demonstrated value, provided case studies that will enable other electric utilities—particularly electric cooperatives— to use these technologies. NRECA structured the project according to the following three areas: Demonstration of smart grid technology; Advancement of standards to enable the interoperability of components; and Improvement of grid cyber security. We termed these three areas Technology Deployment Study, Interoperability, and Cyber Security. Although the deployment of technology and studying the demonstration projects at coops accounted for the largest portion of the project budget by far, we see our accomplishments in each of the areas as critical to advancing the smart grid. All project deliverables have been published. Technology Deployment Study: The deliverable was a set of 11 single-topic technical reports in areas related to the listed technologies. Each of these reports has already been submitted to DOE, distributed to co-ops, and

  2. Gridded ionization chamber

    International Nuclear Information System (INIS)

    Houston, J.M.

    1977-01-01

    An improved ionization chamber type x-ray detector comprises a heavy gas at high pressure disposed between an anode and a cathode. An open grid structure is disposed adjacent the anode and is maintained at a voltsge intermediate between the cathode and anode potentials. The electric field which is produced by positive ions drifting toward the cathode is thus shielded from the anode. Current measuring circuits connected to the anode are, therefore, responsive only to electron current flow within the chamber and the recovery time of the chamber is shortened. The grid structure also serves to shield the anode from electrical currents which might otherwise be induced by mechanical vibrations in the ionization chamber structure

  3. Everything you always want to know about the Grid and never dared to ask

    CERN Multimedia

    CERN. Geneva; Hey, Anthony J G

    2003-01-01

    Sometimes the Grid is called the next-generation Web. The Web makes information available in a transparent and user-friendly way. On the other hand the grid goes one step further in that it enables members of a dynamic, multi-institutional virtual organisation to share distributed computing resources to solve an agreed set of problems in a managed and coordinated fashion. With the grid, users should be unaware whether they are using the computer or data on their own desktop or any other computer or resource connected to the international network. Users get the resources they need, anytime, and from anywhere, with the complexity of the grid infrastructure being hidden from them. The technology needed to implement the grid includes new protocols, services, and APIs for secure resource access, resource management, fault detection, and communication. Moreover, one introduces application concepts such as virtual data, smart instruments, collaborative design spaces, and meta-computations. All over the world nationa...

  4. Gridded Ionization Chamber

    International Nuclear Information System (INIS)

    Manero Amoros, F.

    1962-01-01

    In the present paper the working principles of a gridded ionization chamber are given, and all the different factors that determine its resolution power are analyzed in detail. One of these devices, built in the Physics Division of the JEN and designed specially for use in measurements of alpha spectroscopy, is described. finally the main applications, in which the chamber can be used, are shown. (Author) 17 refs

  5. The Grid PC farm

    CERN Multimedia

    Maximilien Brice

    2006-01-01

    Housed in the CERN Computer Centre, these banks of computers process and store data produced on the CERN systems. When the LHC starts operation in 2008, it will produce enough data every year to fill a stack of CDs 20 km tall. To handle this huge amount of data, CERN has also developed the Grid, allowing processing power to be shared between computer centres around the world.

  6. Simulating the Smart Grid

    OpenAIRE

    Pöchacker, Manfred; Sobe, Anita; Elmenreich, Wilfried

    2013-01-01

    Major challenges for the transition of power systems do not only tackle power electronics but also communication technology, power market economy and user acceptance studies. Simulation is an important research method therein, as it helps to avoid costly failures. A common smart grid simulation platform is still missing. We introduce a conceptual model of agents in multiple flow networks. Flow networks extend the depth of established power flow analysis through use of networks of information ...

  7. Smart Grid Technology

    OpenAIRE

    Cosma Sorinel

    2010-01-01

    The largest interconnected machine on Earth, the century-old power grid is so massively complex and inextricably linked to human involvement and endeavor that it has been called an ecosystem. To meet sustainability requirements, the electric industry is poised to make the transformation from a centralized, producer-controlled network to one that is less centralized and more consumerinteractive. This move promises to change the industry’s entire business model and its relationship with all sta...

  8. A New Orthodontic Appliance with a Mini Screw for Upper Molar Distalization.

    Science.gov (United States)

    Ozkalayci, Nurhat; Yetmez, Mehmet

    2016-01-01

    The aim of this study is to present a new upper molar distalization appliance called Cise distalizer designed as intraoral device supported with orthodontic mini screw for upper permanent molar distalization. The new appliance consists of eight main components. In order to understand the optimum force level, the appliance under static loading is tested by using strain gage measurement techniques. Results show that one of the open coils produces approximately 300 gr distalization force. Cise distalizer can provide totally 600 gr distalization force. This range of force level is enough for distalization of upper first and second molar teeth.

  9. A New Orthodontic Appliance with a Mini Screw for Upper Molar Distalization

    Directory of Open Access Journals (Sweden)

    Nurhat Ozkalayci

    2016-01-01

    Full Text Available The aim of this study is to present a new upper molar distalization appliance called Cise distalizer designed as intraoral device supported with orthodontic mini screw for upper permanent molar distalization. The new appliance consists of eight main components. In order to understand the optimum force level, the appliance under static loading is tested by using strain gage measurement techniques. Results show that one of the open coils produces approximately 300 gr distalization force. Cise distalizer can provide totally 600 gr distalization force. This range of force level is enough for distalization of upper first and second molar teeth.

  10. Energy Savings Potential and Research, Development, & Demonstration Opportunities for Commercial Building Appliances

    Energy Technology Data Exchange (ETDEWEB)

    Zogg, Robert [Navigant Consulting, Inc., Burlington, MA (United States); Goetzler, William [Navigant Consulting, Inc., Burlington, MA (United States); Ahlfeldt, Christopher [Navigant Consulting, Inc., Burlington, MA (United States); Hiraiwa, Hirokazu [Navigant Consulting, Inc., Burlington, MA (United States); Sathe, Amul [Navigant Consulting, Inc., Burlington, MA (United States); Sutherland, Timothy [Navigant Consulting, Inc., Burlington, MA (United States)

    2009-12-01

    This study characterizes and assesses the appliances used in commercial buildings. The primary objectives of this study were to document the energy consumed by commercial appliances and identify research, development and demonstration (RD&D) opportunities for efficiency improvements, excluding product categories such as HVAC, building lighting, refrigeration equipment, and distributed generation systems. The study included equipment descriptions, characteristics of the equipment’s market, national energy consumption, estimates of technical potential for energy-saving technologies, and recommendations for U.S. Department of Energy programs that can promote energy savings in commercial appliances.

  11. Emissions from SF6 appliances in Norway. Additional report No. 2

    International Nuclear Information System (INIS)

    Gjarede, Anne Cathrine

    1999-01-01

    The report presents facts regarding the Norwegian SF 6 emissions and the significance for the Norwegian climatic gas accounts in order to evaluate whether 12-24 kV SF 6 appliances are environmentally acceptable. Estimations show that emissions from such equipment contribute with about 0.2 % of the total Norwegian CO 2 emissions in 1993. The SF 6 which is stored in electric appliances, may either be recycled or decomposed to more environmentally acceptable end products. The report concludes that the contribution to the greenhouse effects from SF 6 appliances is minimal

  12. Grids, Clouds, and Virtualization

    Science.gov (United States)

    Cafaro, Massimo; Aloisio, Giovanni

    This chapter introduces and puts in context Grids, Clouds, and Virtualization. Grids promised to deliver computing power on demand. However, despite a decade of active research, no viable commercial grid computing provider has emerged. On the other hand, it is widely believed - especially in the Business World - that HPC will eventually become a commodity. Just as some commercial consumers of electricity have mission requirements that necessitate they generate their own power, some consumers of computational resources will continue to need to provision their own supercomputers. Clouds are a recent business-oriented development with the potential to render this eventually as rare as organizations that generate their own electricity today, even among institutions who currently consider themselves the unassailable elite of the HPC business. Finally, Virtualization is one of the key technologies enabling many different Clouds. We begin with a brief history in order to put them in context, and recall the basic principles and concepts underlying and clearly differentiating them. A thorough overview and survey of existing technologies provides the basis to delve into details as the reader progresses through the book.

  13. Resilient Grid Operational Strategies

    Energy Technology Data Exchange (ETDEWEB)

    Pasqualini, Donatella [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-03-01

    Extreme weather-related disturbances, such as hurricanes, are a leading cause of grid outages historically. Although physical asset hardening is perhaps the most common way to mitigate the impacts of severe weather, operational strategies may be deployed to limit the extent of societal and economic losses associated with weather-related physical damage.1 The purpose of this study is to examine bulk power-system operational strategies that can be deployed to mitigate the impact of severe weather disruptions caused by hurricanes, thereby increasing grid resilience to maintain continuity of critical infrastructure during extreme weather. To estimate the impacts of resilient grid operational strategies, Los Alamos National Laboratory (LANL) developed a framework for hurricane probabilistic risk analysis (PRA). The probabilistic nature of this framework allows us to estimate the probability distribution of likely impacts, as opposed to the worst-case impacts. The project scope does not include strategies that are not operations related, such as transmission system hardening (e.g., undergrounding, transmission tower reinforcement and substation flood protection) and solutions in the distribution network.

  14. Wireless Communications in Smart Grid

    Science.gov (United States)

    Bojkovic, Zoran; Bakmaz, Bojan

    Communication networks play a crucial role in smart grid, as the intelligence of this complex system is built based on information exchange across the power grid. Wireless communications and networking are among the most economical ways to build the essential part of the scalable communication infrastructure for smart grid. In particular, wireless networks will be deployed widely in the smart grid for automatic meter reading, remote system and customer site monitoring, as well as equipment fault diagnosing. With an increasing interest from both the academic and industrial communities, this chapter systematically investigates recent advances in wireless communication technology for the smart grid.

  15. Development of environmentally friendly briquettes

    International Nuclear Information System (INIS)

    Kleisa, K.; Lehmann, J.; Verfuss, F.; Simon, G.

    1994-01-01

    The DMT has developed an industrial briquette consisting of about 87% hardcoal, 7% molasses pulp and 6% hydration limestone which meets the requirements of the clean air authority as an environmentally friendly fuel for travelling grate boilers. In extensive tests in a 4.4 MW travelling grate boiler these briquettes with molasses and limestone additives proved to be particularly effective in terms of reducing sulphur dioxide emission in the flue gas. They exhibited good ignition and combustion behaviour as well as a considerable reduction in nitrogen oxide emission. In a large-scale test with 1000 t of briquettes in a 46.5 MW travelling grate furnace it proved possible to confirm the good combustion behaviour and the reduced emission of sulphur oxide and nitrogen oxide in the flue gas. (orig.) [de

  16. Environmental friendly energy transport media

    International Nuclear Information System (INIS)

    Wan Nik, W.B.

    2002-01-01

    Rational self-interest and good environmental citizenship are forcing the development of renewable and environmentally, acceptable working fluids. Fluids that are at least equivalent in performance plus biodegradable have been formulated in Europe and USA rising vegetable oils as base stocks and as innovative additive packages. While much of the research has been made in the field of alternative environmentally, friendly energy, transport media, the thermal stability of vegetable based stock is still a challenging area. This work concentrates more in improving the oxidation stability of the vegetable based stocks. Oven and oil bath test methods were employed in this study. This paper tabled mineral and vegetable oil physical test results and presents thermal stability of oil blends. (Author)

  17. Rendez-vous with "InGRID"

    CERN Multimedia

    Laëtitia Pedroso

    2011-01-01

    Pending the elaboration of the master plan which should be implemented in 2013 and the results of a competition for the design of the major public areas between Entrance A and the St. Genis customs (along the Route de Meyrin), CERN and the Canton of Geneva have worked together on the installation of a temporary garden financed by the Canton. The garden will bring a bit of style to the area between Building 33 and the Globe of Science and Innovation.   "InGRID" at night. You may have been wondering what those long arching rods are that have suddenly appeared in front of Building 33. Well, we are pleased to introduce InGRID, the temporary garden that is transforming the old parking area between Building 33 and the Globe into a new pedestrian concourse around the tram stop. This space will serve as a multimodal concourse, a meeting point, a waiting area and a place to chat, reserved for pedestrians, CERN personnel and visitors. “We want to create a user-friendly atmosphe...

  18. Progress in Grid Generation: From Chimera to DRAGON Grids

    Science.gov (United States)

    Liou, Meng-Sing; Kao, Kai-Hsiung

    1994-01-01

    Hybrid grids, composed of structured and unstructured grids, combines the best features of both. The chimera method is a major stepstone toward a hybrid grid from which the present approach is evolved. The chimera grid composes a set of overlapped structured grids which are independently generated and body-fitted, yielding a high quality grid readily accessible for efficient solution schemes. The chimera method has been shown to be efficient to generate a grid about complex geometries and has been demonstrated to deliver accurate aerodynamic prediction of complex flows. While its geometrical flexibility is attractive, interpolation of data in the overlapped regions - which in today's practice in 3D is done in a nonconservative fashion, is not. In the present paper we propose a hybrid grid scheme that maximizes the advantages of the chimera scheme and adapts the strengths of the unstructured grid while at the same time keeps its weaknesses minimal. Like the chimera method, we first divide up the physical domain by a set of structured body-fitted grids which are separately generated and overlaid throughout a complex configuration. To eliminate any pure data manipulation which does not necessarily follow governing equations, we use non-structured grids only to directly replace the region of the arbitrarily overlapped grids. This new adaptation to the chimera thinking is coined the DRAGON grid. The nonstructured grid region sandwiched between the structured grids is limited in size, resulting in only a small increase in memory and computational effort. The DRAGON method has three important advantages: (1) preserving strengths of the chimera grid; (2) eliminating difficulties sometimes encountered in the chimera scheme, such as the orphan points and bad quality of interpolation stencils; and (3) making grid communication in a fully conservative and consistent manner insofar as the governing equations are concerned. To demonstrate its use, the governing equations are

  19. Eco-friendly Development Of Industry

    International Nuclear Information System (INIS)

    An, Gi Cheol; Park, Hun; Lee, Dong Jin; Ryu, Sang Hui

    1998-02-01

    This book reports eco-friendly development of industry, which has summary on bring up the issue and research way and system of research. It deals with current state of affairs on eco-friendly development of industry and the case of developed countries such as necessity and meaning of eco-friendly development industry, prospect and change of the tendency, environmental issue by field in Korea like the steel industry, nonferrous metal industry, auto industry, and cement industry and general policy for eco-friendly development of industry.

  20. Smart Grid Risk Management

    Science.gov (United States)

    Abad Lopez, Carlos Adrian

    Current electricity infrastructure is being stressed from several directions -- high demand, unreliable supply, extreme weather conditions, accidents, among others. Infrastructure planners have, traditionally, focused on only the cost of the system; today, resilience and sustainability are increasingly becoming more important. In this dissertation, we develop computational tools for efficiently managing electricity resources to help create a more reliable and sustainable electrical grid. The tools we present in this work will help electric utilities coordinate demand to allow the smooth and large scale integration of renewable sources of energy into traditional grids, as well as provide infrastructure planners and operators in developing countries a framework for making informed planning and control decisions in the presence of uncertainty. Demand-side management is considered as the most viable solution for maintaining grid stability as generation from intermittent renewable sources increases. Demand-side management, particularly demand response (DR) programs that attempt to alter the energy consumption of customers either by using price-based incentives or up-front power interruption contracts, is more cost-effective and sustainable in addressing short-term supply-demand imbalances when compared with the alternative that involves increasing fossil fuel-based fast spinning reserves. An essential step in compensating participating customers and benchmarking the effectiveness of DR programs is to be able to independently detect the load reduction from observed meter data. Electric utilities implementing automated DR programs through direct load control switches are also interested in detecting the reduction in demand to efficiently pinpoint non-functioning devices to reduce maintenance costs. We develop sparse optimization methods for detecting a small change in the demand for electricity of a customer in response to a price change or signal from the utility