Research into Oil-based Colloidal-Graphite Lubricants for Forging of Al-based Alloys

International Nuclear Information System (INIS)

Petrov, A.; Petrov, P.; Petrov, M.

2011-01-01

The presented paper describes the topical problem in metal forging production. It deals with the choice of an optimal lubricant for forging of Al-based alloys. Within the scope of the paper, the properties of several oil-based colloidal-graphite lubricants were investigated. The physicochemical and technological properties of these lubricants are presented. It was found that physicochemical properties of lubricant compositions have an influence on friction coefficient value and quality of forgings.The ring compression method was used to estimate the friction coefficient value. Hydraulic press was used for the test. The comparative analysis of the investigated lubricants was carried out. The forging quality was estimated on the basis of production test. The practical recommendations were given to choose an optimal oil-based colloidal-graphite lubricant for isothermal forging of Al-based alloy.

Hydroprocessing of Jatropha Oil for Production of Green Diesel over Non-sulfided Ni-PTA/Al2O3 Catalyst

Science.gov (United States)

Liu, Jing; Lei, Jiandu; He, Jing; Deng, Lihong; Wang, Luying; Fan, Kai; Rong, Long

2015-01-01

The non-sulfided Ni-PTA/Al2O3 catalyst was developed to produce green diesel from the hydroprocessing of Jatropha oil. The Ni-PTA/Al2O3 catalyst was prepared by one-pot synthesis of Ni/Al2O3 with the co-precipitation method and then impregnanting Ni/Al2O3 with PTA solution. The catalysts were characterized with BET, SEM-EDX, TEM, XRD, XPS, TGA and NH3-TPD. The Ni and W species of the Ni-PTA/Al2O3 catalyst were much more homogeneously distributed on the surface than that of commercial Al2O3. Catalytic performance in the hydroprocessing of Jatropha oil was evaluated by GC. The maximum conversion of Jatropha oil (98.5 wt%) and selectivity of the C15-C18 alkanes fraction (84.5 wt %) occurred at 360 °C, 3.0 MPa, 0.8 h−1. The non-sulfided Ni-PTA/Al2O3 catalyst is more environmentally friendly than the conventional sulfided hydroprocessing catalyst, and it exhibited the highest catalytic activity than the Ni-PTA catalyst supported with commercial Al2O3 grain and Al2O3 powder. PMID:26162092

Preparation of nano-sized α-Al2O3 from oil shale ash

International Nuclear Information System (INIS)

An, Baichao; Wang, Wenying; Ji, Guijuan; Gan, Shucai; Gao, Guimei; Xu, Jijing; Li, Guanghuan

2010-01-01

Oil shale ash (OSA), the residue of oil shale semi-coke roasting, was used as a raw material to synthesize nano-sized α-Al 2 O 3 . Ultrasonic oscillation pretreatment followed by azeotropic distillation was employed for reducing the particle size of α-Al 2 O 3 . The structural characterization at molecular and nanometer scales was performed using X-ray diffraction (XRD), transmission electron microscopy (TEM), respectively. The interaction between alumina and n-butanol was characterized by Fourier transform infrared spectroscopy (FT-IR). The results revealed that the crystalline phase of alumina nanoparticles was regular and the well dispersed alumina nanoparticles had a diameter of 50-80 nm. In addition, the significant factors including injection rate of carbon oxide (CO 2 ), ultrasonic oscillations, azeotropic distillation and surfactant were investigated with respect to their effects on the size of the alumina particles.

Investigation of activated Al-pillared clay efficiency in vegetable oil purification

Directory of Open Access Journals (Sweden)

Lomić Gizela A.

2004-01-01

Full Text Available This paper represents a contribution to the applicability of natural clays and their derivates as adsorbents in the process of purification of vegetable oil. Investigation of textural properties of raw and purified clay samples reveals that during acid activation and Al-pillaring, BET and micropore surface area increases significantly. However, bleaching capacity of clay and its derivates is not determined by using sample surface area, but rather sample total pore volume. Surface area, especially micropore surface area contributes to removal of smaller molecules. This was confirmed by successful elimination of moisture and volatile materials by samples with an appropriate micropore structure. Used samples of clay and its derivates do not significantly influence acid and peroxide values of raw sunflower oil during its treatment.

Desulfurization of AL-Ahdab Crude Oil using Oxidative Processes

Directory of Open Access Journals (Sweden)

Neran Khalel Ibrahim

2015-07-01

Full Text Available Two different oxidative desulfurization strategies based on oxidation/adsorption or oxidation/extraction were evaluated for the desulfurization of AL-Ahdab (AHD sour crude oil (3.9wt% sulfur content. In the oxidation process, a homogenous oxidizing agent comprising of hydrogen peroxide and formic acid was used. Activated carbons were used as sorbent/catalyst in the oxidation/adsorption process while acetonitrile was used as an extraction solvent in the oxidation/extraction process. For the oxidation/adsorption scheme, the experimental results indicated that the oxidation desulfurization efficiency was enhanced on using activated carbon as catalyst/sorbent. The effects of the operating conditions (contact time, temperature, mixing speed and sorbent dose on the desulfurization efficiency were examined. The desulfurization efficiency measured at the best operating conditions(optimum conditions: 60 , 500rpm, 60min contact time and sorbent dose of 0.7g AC/100 ml AHD crude, was 32.8% corresponding to a sulfur content of 2.6 wt%. Applying the same optimum operating conditions and at 3:1 solvent/oil ratio, the oxidation/extraction method gave comparable desulfurization efficiency of 31.5%.

Efficient KF loaded on MgCaAl hydrotalcite-like compounds in the transesterification of Jatropha curcas oil

International Nuclear Information System (INIS)

Guzmán-Vargas, Ariel; Santos-Gutiérrez, Teresa; Lima, Enrique; Flores-Moreno, Jorge L.; Oliver-Tolentino, Miguel A.; Martínez-Ortiz, María de J.

2015-01-01

Highlights: • MgCaAl hydrotalcite-like compounds were synthetized. • After KF impregnation and calcination fluorinated species were detected. • Fluorinated species were stables and actives. • LDH composition and KF load effect were evaluated in biodiesel production. - Abstract: In this work a series of MgCaAl hydrotalcite-like compounds were synthetized by coprecipitation method at constant pH. In order to obtain the catalysts, the samples were modified with KF by incipient wetness impregnation at different wt%, after that, they were dried and calcined to obtain the mixed oxides. The effect of divalent cations ratio and KF load were studied in the transesterification reaction of Jatropha curcas oil to obtain biodiesel employing an inedible oil. XRD analysis showed typical diffraction patterns of LDH, by nitrogen physisorption the LDH mesoporous structure was also confirmed, 27 Al NMR spectra showed bands at 10 and 88 ppm attributed to the Al coordination before and after thermal treatment. While for the impregnated samples after calcination the profiles exhibited the mixed oxide formation, in addition, another peaks appeared associated to the formation of various fluorinated species as shown by XRD, additionally, 19 F NMR showed a main signal at −180 ppm indicating the presence of active tetrahedral aluminum fluoride species. The reaction evolution was monitoring calculating the oil conversion to biodiesel by integration of the signal spectra using 1 H NMR spectroscopy. The results of catalytic tests in transesterification reaction showed a direct correlation between Mg/Ca ratio and KF content in the oil conversion to biodiesel, the higher conversion was achieved (90%) when Mg/Ca = 1 and KF load was 30 wt%

Efficient KF loaded on MgCaAl hydrotalcite-like compounds in the transesterification of Jatropha curcas oil

Energy Technology Data Exchange (ETDEWEB)

Guzmán-Vargas, Ariel, E-mail: aguzmanv@ipn.mx [ESIQIE-IPN, Departamento de Ingeniería Química, Laboratorio de Investigación en Materiales Porosos, Catálisis Ambiental y Química Fina, UPALM Edif.7 P.B. Zacatenco, México D.F. 07738 (Mexico); Santos-Gutiérrez, Teresa [ESIQIE-IPN, Departamento de Ingeniería Química, Laboratorio de Investigación en Materiales Porosos, Catálisis Ambiental y Química Fina, UPALM Edif.7 P.B. Zacatenco, México D.F. 07738 (Mexico); Lima, Enrique [IIM-Universidad Nacional Autónoma de México, Circuito exterior s/n, Cd. Universitaria, 04510 México DF (Mexico); Flores-Moreno, Jorge L. [UAM-Azcapotzalco, Área de Química de Materiales, Av. San Pablo 180, Col. Reynosa Tamaulipas, 02200 México DF (Mexico); Oliver-Tolentino, Miguel A.; Martínez-Ortiz, María de J. [ESIQIE-IPN, Departamento de Ingeniería Química, Laboratorio de Investigación en Materiales Porosos, Catálisis Ambiental y Química Fina, UPALM Edif.7 P.B. Zacatenco, México D.F. 07738 (Mexico)

2015-09-15

Highlights: • MgCaAl hydrotalcite-like compounds were synthetized. • After KF impregnation and calcination fluorinated species were detected. • Fluorinated species were stables and actives. • LDH composition and KF load effect were evaluated in biodiesel production. - Abstract: In this work a series of MgCaAl hydrotalcite-like compounds were synthetized by coprecipitation method at constant pH. In order to obtain the catalysts, the samples were modified with KF by incipient wetness impregnation at different wt%, after that, they were dried and calcined to obtain the mixed oxides. The effect of divalent cations ratio and KF load were studied in the transesterification reaction of Jatropha curcas oil to obtain biodiesel employing an inedible oil. XRD analysis showed typical diffraction patterns of LDH, by nitrogen physisorption the LDH mesoporous structure was also confirmed, {sup 27}Al NMR spectra showed bands at 10 and 88 ppm attributed to the Al coordination before and after thermal treatment. While for the impregnated samples after calcination the profiles exhibited the mixed oxide formation, in addition, another peaks appeared associated to the formation of various fluorinated species as shown by XRD, additionally, {sup 19}F NMR showed a main signal at −180 ppm indicating the presence of active tetrahedral aluminum fluoride species. The reaction evolution was monitoring calculating the oil conversion to biodiesel by integration of the signal spectra using {sup 1}H NMR spectroscopy. The results of catalytic tests in transesterification reaction showed a direct correlation between Mg/Ca ratio and KF content in the oil conversion to biodiesel, the higher conversion was achieved (90%) when Mg/Ca = 1 and KF load was 30 wt%.

Synthesis of Green Diesel From Waste Cooking Oil Through Hydrodeoxygenation Technology With NiMo/γ-Al2O3 Catalysts

Directory of Open Access Journals (Sweden)

Heriyanto Heri

2018-01-01

Full Text Available Hydrodeoxygenation (HDO of waste cooking oil (WCO and trapped grease over sulfide catalysts was examined to produce high quality transportation fuel from low-grade resources. The hydrodeoxygenation of waste cooking oils was carried out in a high pressure of 30 and 60 bar and high temperature of 300 – 400 °C in a batch reactor autoclave. NiMo/γ-Al2O3 catalyst was prepared and for the first time tested in hydroprocessing of waste cooking oil. The content of NiMo/γ-Al2O3 in each catalyst was about wCo 5 wt.%. A maximum of 77,97 % green diesel yield was achieved at nearly complete conversion of waste cooking oil using NiMo/γ-Al2O3 at temperature of 400°C, pressure 60 bar and 4 hours of reaction time. The oxygen content was decreased from 14,25 wt.% to 13,35 wt.%, at temperature of 400°C, pressure of 30 bar and 1 hour of reaction time. The Hydrodeoxygenation process was much influenced by temperature, pressure, and time.

Optimization of the Transesterification of Waste Cooking Oil with Mg-Al Hydrotalcite Using Response Surface Methodology

Directory of Open Access Journals (Sweden)

Laureano Costarrosa

2018-01-01

Full Text Available Nowadays, biodiesel has become a very promising alternative to fossil diesel fuel, regarding environmental concerns and fuel resource depletion. Biodiesel is usually produced through homogeneous or heterogeneous transesterification of different fatty raw materials. Although main research has been carried out with homogenous catalysts, heterogeneous catalysts may be of interest due to ease of recovery and recycling, as well as readiness for continuous processing. In this work, calcined Mg-Al hydrotalcite (HT was used for the heterogeneous transesterification of waste cooking oil. Three reaction parameters, namely, reaction time, amount of catalyst, and methanol-to-oil molar ratio, were optimized by means of Response Surface Methodology (RSM at constant temperature (65 °C, using a Box-Behnken design. Optimal fatty acid methyl ester (FAME content (86.23% w/w FAME/sample was predicted by the model with an R-squared value of 98.45%, using 3.39 g of HT (8.5% w/w oil and an 8:1 methanol-oil molar ratio, for a duration of 3.12 h. It was observed that calcination of HT, while avoiding the previous washing step, allowed the presence of chemical species that enhanced the effect of the catalyst. It can be concluded from this field trial that calcined and nonwashed Mg-Al hydrotalcite may be considered an effective basic catalyst for the production of biodiesel from waste cooking oil. Also, RSM proved to be a useful tool for predicting biodiesel yield.

Bio diesel Production via Transesterification of Palm Oil Using NaOH/ Al2O3 Catalysts

International Nuclear Information System (INIS)

Taufiq Yap Yun Hin; Nurul Fitriyah Abdullah; Mahiran Basri; Taufiq Yap Yun Hin; Nurul Fitriyah Abdullah

2011-01-01

Due to the increase in price of petroleum and environmental concerns, the search for alternative fuels has gained importance. In this work, bio diesel production by transesterification of palm oil with methanol has been studied in a heterogeneous system using sodium hydroxide loaded on alumina (NaOH/ Al 2 O 3 ). NaOH/ Al 2 O 3 catalyst was prepared by impregnation of alumina with different amount of an aqueous solution of sodium hydroxide followed by calcination in air for 3 h. The prepared catalysts were then characterized by using x-ray diffraction (XRD), Fourier transform infrared spectrometer (FT-IR), Brunner-Emmett-Teller surface area measurement (BET), scanning electron microscopy (SEM) and temperature-programmed desorption of CO 2 (CO 2 -TPD). Moreover, the dependence of the conversion of palm oil on the reactions variables such as the molar ratio of methanol/oil, the amount of catalysts used, reaction temperatures and reaction times were performed. The conversion of 99 % was achieved under the optimum reaction conditions. The bio diesel obtained was characterized by FT-IR and the pour point was measured. (author)

Preparation of nano-sized {alpha}-Al{sub 2}O{sub 3} from oil shale ash

Energy Technology Data Exchange (ETDEWEB)

An, Baichao; Wang, Wenying; Ji, Guijuan; Gan, Shucai; Gao, Guimei; Xu, Jijing; Li, Guanghuan [College of Chemistry, Jilin University, Changchun 130026 (China)

2010-01-15

Oil shale ash (OSA), the residue of oil shale semi-coke roasting, was used as a raw material to synthesize nano-sized {alpha}-Al{sub 2}O{sub 3}. Ultrasonic oscillation pretreatment followed by azeotropic distillation was employed for reducing the particle size of {alpha}-Al{sub 2}O{sub 3}. The structural characterization at molecular and nanometer scales was performed using X-ray diffraction (XRD), transmission electron microscopy (TEM), respectively. The interaction between alumina and n-butanol was characterized by Fourier transform infrared spectroscopy (FT-IR). The results revealed that the crystalline phase of alumina nanoparticles was regular and the well dispersed alumina nanoparticles had a diameter of 50-80 nm. In addition, the significant factors including injection rate of carbon oxide (CO{sub 2}), ultrasonic oscillations, azeotropic distillation and surfactant were investigated with respect to their effects on the size of the alumina particles. (author)

Transesterification of Jatropha oil with dimethyl carbonate to produce fatty acid methyl ester over reusable Ca–La–Al mixed-oxide catalyst

International Nuclear Information System (INIS)

Syamsuddin, Y.; Murat, M.N.; Hameed, B.H.

2015-01-01

Highlights: • Transesterification of Jatropha oil over CaO-based catalyst. • Physicochemical properties of the synthesized catalyst. • Best reaction condition for FAME synthesis. • The catalyst showed high activity and stability for transesterification with Jatropha oil. - Abstract: Jatropha oil (JO) was transesterified with dimethyl carbonate (DMC) to produce fatty acid methyl ester (FAME) over synthesized Ca–La–Al mixed-oxide catalyst. The influence of different parameters on transesterification of Jatropha oil was investigated in a batch reactor. These parameters included reaction temperature (110–160 °C), reaction time (30–240 min), DMC-to-oil molar ratio (4:1–18:1) and catalyst loading amount (1–10 wt.%, based on the oil weight). The mixed-oxide catalyst with a molar ratio of 6:2:1 (Ca–La–Al) showed high catalytic activity for FAME synthesis. More than 90% of FAME was obtained under the following reaction conditions: 150 °C, reaction temperature; 180 min, reaction time; 15:1, DMC-to-oil molar ratio; and 7 wt.% amount of catalyst loading. The catalyst also exhibited high stability and could be reused for up to five cycles with less than 5% yield reduction per cycle.

Corn fiber oil lowers plasma cholesterol levels and increases cholesterol excretion greater than corn oil and similar to diets containing soy sterols and soy stanols in hamsters.

Science.gov (United States)

Wilson, T A; DeSimone, A P; Romano, C A; Nicolosi, R J

2000-09-01

compared to the stanol diet. The CFO, sterol, and stanol diets excreted significantly more fecal cholesterol compared to the coconut oil and CO diets. In summary, CFO reduces plasma and hepatic cholesterol concentrations and increases fecal cholesterol excretion greater than CO through some other mechanism(s) in addition to increase dietary sterols and stanols-possibly oryzanols.

A novel exopolysaccharide elicitor from endophytic fungus Gilmaniella sp. AL12 on volatile oils accumulation in Atractylodes lancea

Science.gov (United States)

Chen, Fei; Ren, Cheng-Gang; Zhou, Tong; Wei, Yu-Jia; Dai, Chuan-Chao

2016-10-01

Endophytes and plants can establish specific long-term symbiosis through the accumulation of secondary metabolites. Previous studies have shown that the endophytic fungus Gilmaniella sp. AL12 can stimulate Atractylodes lancea to produce volatile oils. The purpose of this report is to investigate key factors involved in the stimulation of A. lancea by AL12 and reveal the mechanism. We identified the active component from AL12 as an extracellular mannan with a polymerization degree of 26-42. Differential membrane proteomics of A. lancea was performed by 2D electrophoresis. The results showed that there were significant differences in the expression of 83 proteins. Based on these results, we conclude that AL12 secreted mannan contributes to the antagonistic balance seen in interactions between AL12 and A. lancea. One portion of the mannan was degraded to mannose for hexokinase activation, promoting photosynthesis and energy metabolism, with a potential metabolic fluxes flowing towards terpenoid biosynthesis. The other portion of the mannan directly enhanced autoimmunity of A. lancea through G protein-mediated signal transduction and the mannan-binding lectin pathway. Volatile oil accumulation was ultimately promoted in subsequent defense reactions. This study provides a new perspective on the regulation of secondary metabolites by endophytic fungal elicitors in medicinal plants.

Production of Bio-Hydrogenated Diesel by Hydrotreatment of High-Acid-Value Waste Cooking Oil over Ruthenium Catalyst Supported on Al-Polyoxocation-Pillared Montmorillonite

Directory of Open Access Journals (Sweden)

Kinya Sakanishi

2012-02-01

Full Text Available Waste cooking oil with a high-acid-value (28.7 mg-KOH/g-oil was converted to bio-hydrogenated diesel by a hydrotreatment process over supported Ru catalysts. The standard reaction temperature, H2 pressure, liquid hourly space velocity (LHSV, and H2/oil ratio were 350 °C, 2 MPa, 15.2 h–1, and 400 mL/mL, respectively. Both the free fatty acids and the triglycerides in the waste cooking oil were deoxygenated at the same time to form hydrocarbons in the hydrotreatment process. The predominant liquid hydrocarbon products (98.9 wt% were n-C18H38, n-C17H36, n-C16H34, and n-C15H32 when a Ru/SiO2 catalyst was used. These long chain normal hydrocarbons had high melting points and gave the liquid hydrocarbon product over Ru/SiO2 a high pour point of 20 °C. Ru/H-Y was not suitable for producing diesel from waste cooking oil because it formed a large amount of C5–C10 gasoline-ranged paraffins on the strong acid sites of HY. When Al-polyoxocation-pillared montmorillonite (Al13-Mont was used as a support for the Ru catalyst, the pour point of the liquid hydrocarbon product decreased to −15 °C with the conversion of a significant amount of C15–C18 n-paraffins to iso-paraffins and light paraffins on the weak acid sites of Al13-Mont. The liquid product over Ru/Al13-Mont can be expected to give a green diesel for current diesel engines because its chemical composition and physical properties are similar to those of commercial petro-diesel. A relatively large amount of H2 was consumed in the hydrogenation of unsaturated C=C bonds and the deoxygenation of C=O bonds in the hydrotreatment process. A sulfided Ni-Mo/Al13-Mont catalyst also produced bio-hydrogenated diesel by the hydrotreatment process but it showed slow deactivation during the reaction due to loss of sulfur. In contrast, Ru/Al13-Mont did not show catalyst deactivation in the hydrotreatment of waste cooking oil after 72 h on-stream because the waste cooking oil was not found to contain sulfur

Thermal stability and fracture toughness of epoxy resins modified with epoxidized castor oil and Al2O3 nanoparticles

International Nuclear Information System (INIS)

Zhu, Lin; Jin, Fanlong; Park, Soojin

2012-01-01

This study examined the effects of the epoxidized castor oil (ECO) and Al 2 O 3 content on the thermal stability and fracture toughness of the diglycidylether of bisphenol-A (DGEBA)/ECO/Al 2 O 3 ternary composites using a range of techniques. The thermal stability of the composites was decreased by the addition of ECO and Al 2 O 3 nanoparticles. The fracture toughness of the composites was improved significantly by the addition of ECO and Al 2 O 3 nanoparticles. The composite containing 3 wt % Al 2 O 3 nanoparticles showed the maximum flexural strength. Scanning electron microscopy (SEM) revealed tortuous cracks in the DGEBA/ECO/Al 2 O 3 composites, which prevented deformation and crack propagation

Deoxygenation of palm kernel oil to jet fuel-like hydrocarbons using Ni-MoS_2/γ-Al_2O_3 catalysts

International Nuclear Information System (INIS)

Itthibenchapong, Vorranutch; Srifa, Atthapon; Kaewmeesri, Rungnapa; Kidkhunthod, Pinit; Faungnawakij, Kajornsak

2017-01-01

Highlights: • The Ni-MoS_2/γ-Al_2O_3 catalysts synthesized using thiourea solution processing. • The Ni-MoS_2 showed semi-amorphous crystallinity with crystallite size of 5–10 nm. • The Ni K-edge XANES and EXAFS indicated the Ni substitution in MoS_2 structure. • A high yield of jet fuel-like hydrocarbon (>90%) from the palm kernel oil feedstock. • The HDO pathway was highly selective, while the DCO_2 and DCO pathways were minor. - Abstract: In the current study, palm kernel oil was used as a renewable feedstock for production of jet fuel-like hydrocarbons via the deoxygenation over the Ni-MoS_2/γ-Al_2O_3 catalyst. The dominant C12 fatty acid content in palm kernel oil makes it promising for jet fuel application. Synthesized by a liquid processing method with thiourea organosulfur agent, the catalyst revealed MoS_2 structure with low stacking, while Ni substitution in the MoS_2 structure and interaction with the Al_2O_3 support were determined based on the Ni K-edge XANES and EXAFS results. A high hydrodeoxygenation (HDO) activity, which as the major pathway in the deoxygenation, was observed upon application of a H_2 pressure of 30–50 bar over Ni-MoS_2/γ-Al_2O_3. The optimum product yield of approximately 92% was obtained mainly from the HDO pathway (∼60%) with 58% selectivity to C10–C12 jet fuel hydrocarbons. The flow property of the jet fuel-like hydrocarbons was more desirable than those obtained from palm olein oil-derived fuel.

Biofuel Production from Jatropha Bio-Oil Derived Fast Pyrolysis: Effect and Mechanism of CoMoS Supported on Al2O3

Science.gov (United States)

Rodseanglung, T.; Ratana, T.; Phongaksorn, M.; Tungkamani, S.

2018-03-01

The aims of this research was to understand the CoMo/Al2O3 sulfide catalyst effect to remove oxygen-containing and nitrogen-containing molecules from Jatropha bio-oil derived fast pyrolysis converted to biofuels via hydrotreating process. The activity and selectivity of CoMo/γ-Al2O3 sulfided catalysts in hydrodeoxygenation (HDO) of Jatropha bio-oil derived fast pyrolysis was evaluated in a Parr batch reactor under 50 bar of H2 atmosphere for 2 h at 300 320 and 340 °C. It appeared that the CoMo/Al2O3 sulfide catalyst have high performance in activity for promoting the fatty acid, fatty ester, fatty amide and fatty nitrile compounds were converted to paraffin/olefin (Diesel range), this could be the CUS site on supported Al2O3 catalyst. The difference in selectivity products allowed us to propose a reaction scheme.

Synthesis by combustion reaction of ZnAl2O4 and application in methyl alcoholysis of soybean oil

International Nuclear Information System (INIS)

Dantas, B.B.; Silva, A.S.; Cunha, R.B.L.; Leal, E.; Costa, A.C.F.M.

2011-01-01

Biodiesel currently presents itself as a viable alternative to diesel oil front. However, implementation of actions most economic use as heterogeneous catalysts, allows further reduction of this biofuel by procedural steps. This work was supported application of catalytic ZnAl 2 O 4 obtained by combustion reaction in methyl alcoholysis of soybean oil. Samples of the supports were characterized by XRD, textural analysis by nitrogen adsorption and FTIR. The reaction tests were performed at 200°C, molar ratio 1:25, 2 and 4 wt% of catalyst and reaction time of 3 hours. XRD results indicate that the phase was obtained ZnAl 2 O 4 effectively, with surface areas of 14.9 and 8.6 m 2 g -1 . The tests demonstrated that reactional higher content of ester was 56.1 and 63.1% for the percentage of catalyst 2 and 4% respectively. (author)

Efficacy of oral iodized peanut oil is greater than that of iodized poppy seed oil among Indonesian schoolchildren

NARCIS (Netherlands)

Untoro, J.; Schultink, J.W.; West, C.E.; Gross, R.; Hautvast, J.G.A.J.

2006-01-01

Background: Oral iodized poppy seed oil is an appropriate measure for controlling iodine deficiency in areas where iodized salt is not yet available. However, a more effective and cheaper iodized oil preparation is needed. Objective: The aim of this study was to compare the efficacy of iodized

BIODIESEL FUELS FROM PALM OIL, PALM OIL METHYLESTER ...

African Journals Online (AJOL)

a

determined by methods outlined by A.O.C.S. (American Oil Chemist Society) [12], Usoro et al. [15], Clark [2], and ... diesel have shown that novel vegetable diesels could be obtained from palm oil. .... C-H stretch for alkenes and aromatics.

Al Jazeera and the DoD: The Need for Greater Engagement

Science.gov (United States)

2013-04-01

noble underdog and America as the vengeful, colonial aggressor. A general cynicism about Arab regimes allied to America is detectable, and though Al...political and public opposition to its coverage. Al Jazeera is also exceeding its nearest competitors in global influence in brand name alone. In a 2006...according to Josh Rushing make Al Jazeera “arguably the most influential news brand across the world.”201 It is a reasonable assumption Al Jazeera’s brand

The Asymmetric Effects of Oil Shocks on an Oil-exporting Economy

OpenAIRE

Omar Mendoza; David Vera

2010-01-01

We estimate the effects of unexpected changes in oil prices on output for the case of Venezuela, an oil-exporting economy. Following Hamilton (2003), Lee et al. (1995), and Mork (1989), we estimate measures of oil shocks and determine the effect of these

KENYA’S OIL PIPELINE AND TERRORISM

Directory of Open Access Journals (Sweden)

E.O.S.ODHIAMBO

2014-04-01

Full Text Available The threat of Al-Shabaab and Al-Qaeda terrorist attacks on the critical infrastructure (oil pipeline in Kenya has brought to the attention the strategic issue of the energy sector security, highlighting the potential vulnerabilities of this sector. Critical Infrastructure Protection (CIP should be a key component of the national security especially after the Kenya Defence Forces’ (KDF incursion into Somalia. The merger of Al-Shabaab and Al-Qaeda terrorist groups and the accelerated grenades attack against Kenya in retaliation has become the centre of the debate on terrorism and internal security of the Kenya. The energy resources are strategic assets from the security, political and economic point of view. Kenya as an oil transit country is considered of primary strategic importance at international level. International terrorism has always looked with interest at the oil resource in order to meet its political and economic targets. We argue that Kenya’s oil pipelines are vulnerable to Al-Shabaab and Al-Qaeda terrorist attack. In summary, the article looks at the concept of terrorism within the framework of critical infrastructure protection, the dangers of attacks on oil pipelines, Kenya’s government preparedness and recommendations.

Influence of oil and mineral characteristics on oil-mineral interaction

International Nuclear Information System (INIS)

Wood, P.A.; Lunel, T.; Daniel, F.; Swannell, R.; Lee, K.; Stoffyn-Egli, P.

1998-01-01

A laboratory study was conducted to simulate the process of oil-mineral interaction in seawater. Thirteen different crudes, emulsions and oil products were used in the study. The objective was to improve the fundamental understanding of the characteristics of oils and minerals that influence the process. The findings of an initial phase of studies based on the swirling flask and marine simulation procedures were also described. Oil content associated with flocs to oil and mineral characteristics were discussed. Emulsions were prepared at 10 degrees C by vigorously mixing the oil with excess artificial seawater in a Kilner jar using a high shear homogenizer. Topped oils were prepared by distillation to 250 degrees C. The biodegraded oil was prepared from the topped crude oil. Biodegradation was achieved over a 28 day period using natural seawater and naturally occurring hydrocarbon degraders. The relationships between oil concentration, oil density and mineral exchange capacity were determined. The study showed that greater oil concentrations in the water column could be expected with (1) the presence of mineral fines, (2) minerals with greater cation exchange rates, (3) minerals with finer sizes, and (4) oils of lower viscosity and density. It was determined that in coastal waters the viscosity of the oil/emulsion will likely be the main factor affecting oil-mineral interactions. The viscosity limit for allowing oil fines interaction is likely to be dependent on the energy in the coastal zone affected by the oil pollution. 18 refs., 5 tabs., 13 figs

Effects of dietary conjugated linoleic acid, fish oil and soybean oil on ...

African Journals Online (AJOL)

Dear User!

2013-12-18

Dec 18, 2013 ... The chickens fed diets containing palm oil, soybean oil or fish oil as the ... polyunsaturated fatty acids; LDL, low density lipoprotein; HDL, .... content of muscles in broilers fed different dietary CLA levels. Javadi et al. (2007) ...

Lubrication performance and mechanisms of Mg/Al-, Zn/Al-, and Zn/Mg/Al-layered double hydroxide nanoparticles as lubricant additives

International Nuclear Information System (INIS)

Li, Shuo; Bhushan, Bharat

2016-01-01

Highlights: • Mg/Al-, Zn/Al- and Zn/Mg/Al-layered double hydroxide were synthesized. • Mg/Al-LDH had superior tribological performance compared to other LDHs. • The best thermal stability of Mg/Al-LDH was responsible for its friction property. - Abstract: Solid lubricant particles are commonly used as oil additives for low friction and wear. Mg/Al-, Zn/Al-, and Zn/Mg/Al-layered double hydroxides (LDH) were synthesized by coprecipitation method. The benefits of LDH nanoparticles are that they can be synthesized using chemical methods where size and shape can be controlled, and can be modified organically to allow dispersal in fluids. The LDH nanoparticles were characterized by X-ray diffraction, scanning electron microscope, thermogravimetry, and differential scanning calorimetry. A pin-on-disk friction and wear tester was used for evaluating the friction and wear properties of LDH nanoparticles as lubricant additives. LDH nanoparticles have friction-reducing and anti-wear properties compared to oil without LDHs. Mg/Al-LDH has the best lubrication, possibly due to better thermal stability in severe conditions.

Lubrication performance and mechanisms of Mg/Al-, Zn/Al-, and Zn/Mg/Al-layered double hydroxide nanoparticles as lubricant additives

Energy Technology Data Exchange (ETDEWEB)

Li, Shuo [School of Materials Science and Technology, China University of Geosciences (Beijing), 29 Xueyuan Road, Haidian Distract, Beijing 100083 (China); Nanoprobe Laboratory for Bio- & Nanotechnology and Biomimetics (NLBB), The Ohio State University, 201 W. 19th Avenue Columbus, OH 43210-1142 (United States); Bhushan, Bharat, E-mail: bhushan.2@osu.edu [Nanoprobe Laboratory for Bio- & Nanotechnology and Biomimetics (NLBB), The Ohio State University, 201 W. 19th Avenue Columbus, OH 43210-1142 (United States)

2016-08-15

Highlights: • Mg/Al-, Zn/Al- and Zn/Mg/Al-layered double hydroxide were synthesized. • Mg/Al-LDH had superior tribological performance compared to other LDHs. • The best thermal stability of Mg/Al-LDH was responsible for its friction property. - Abstract: Solid lubricant particles are commonly used as oil additives for low friction and wear. Mg/Al-, Zn/Al-, and Zn/Mg/Al-layered double hydroxides (LDH) were synthesized by coprecipitation method. The benefits of LDH nanoparticles are that they can be synthesized using chemical methods where size and shape can be controlled, and can be modified organically to allow dispersal in fluids. The LDH nanoparticles were characterized by X-ray diffraction, scanning electron microscope, thermogravimetry, and differential scanning calorimetry. A pin-on-disk friction and wear tester was used for evaluating the friction and wear properties of LDH nanoparticles as lubricant additives. LDH nanoparticles have friction-reducing and anti-wear properties compared to oil without LDHs. Mg/Al-LDH has the best lubrication, possibly due to better thermal stability in severe conditions.

Optimization Of Process Parameters For The Production Of Bio diesel From Waste Cooking Oil In The Presence Of Bifunctional γ-Al2O3-CeO2 Supported Catalysts

International Nuclear Information System (INIS)

Anita Ramli; Muhammad Farooq

2015-01-01

Huge quantities of waste cooking oils are produced all over the world every day, especially in the developed countries with 0.5 million ton per year waste cooking oil are being generated in Malaysia alone. Such large amount of waste cooking oil production can create disposal problems and contamination to water and land resources if not disposed properly. The use of waste cooking oil as feedstock for bio diesel production will not only avoid the competition of the same oil resources for food and fuel but will also overcome the waste cooking oil disposal problems. However, waste cooking oil has high acid value, thus would require the oil to undergo esterification with an acid catalyst prior to transesterification with a base catalyst. Therefore, in this study, bifunctional catalyst supports were developed for one-step esterification-transesterification of waste cooking oil by varying the CeO 2 loading on γ-Al 2 O 3 . The bifunctional supports were then impregnated with 5 wt % Mo and characterized using N 2 adsorption-desorption isotherm to determine the surface area of the catalysts while temperature programmed desorption with NH 3 and CO 2 as adsorbents were used to determine the acidity and basicity of the catalysts. Results show that the γ-Al 2 O 3 -CeO 2 supported Mo catalysts are active for the one-step esterification-transesterification of waste cooking oil to produce bio diesel with the Mo/ γ-Al 2 O 3 -20 wt% CeO 2 as the most active catalyst. Optimization of process parameters for the production of bio diesel from waste cooking oil in the presence of this catalyst show that 81.1 % bio diesel yield was produced at 110 degree Celsius with catalyst loading of 7 wt %, agitation speed of 600 rpm, methanol to oil ratio of 30:1 and reaction period of 270 minutes. (author)

Synthetic lubricating oils

Energy Technology Data Exchange (ETDEWEB)

Rodriguez Jurado, J

1953-01-01

A yellow solid petroleum paraffin d/sup 60/ 0.808, I number 3.5, average molecular weight 350, chlorinated and condensed with benzene, xylene, or naphthalene by the Friedel and Crafts reaction, in the presence of anhydrous AlCl/sub 3/ or activated Al, gave synthetic lubricating oils. Xylene was the preferred aromatic compound, naphthalene required the use of less completely chlorinated paraffin, benzene produced resins difficult to remove and gave darker oils with excessive green fluorescence. Activated Al rather than anhydrous AlCl/sub 3/ gave darker oils with higher viscosity and Conradson C values. Tar from the low-temperature distillation of lignite, used as a source of a paraffin fraction melting 40/sup 0/ to 48/sup 0/ (chlorinated to 26.5 percent Cl) and an aromatic fraction, 45 percent aromatic compounds by volume (mainly polysubstituted benzenes), I number 10, was converted to a similar synthetic lubricant with the following properties: Kinematic viscosity at 210/sup 0/ F., 50.4 centistokes; viscosity index, 92; Conradson C, 1.5 percent; solidification point, 9/sup 0/; S, 0.41 percent.

AL-PAM assisted filtration of mature fine tailings produced from oil sands development

Energy Technology Data Exchange (ETDEWEB)

Alamgir, A.; Masliyah, J.; Xu, Z. [Alberta Univ., Edmonton, AB (Canada). Dept. of Chemical and Materials Engineering

2010-07-01

The inventory of mature fine tailings (MFT) produced by the oil sands extraction process continues to grow, and is considered as a long-term environmental liability. Large amounts of water are trapped in the MFT, and the tailings ponds present a threat to local wildlife and ecosystems. This PowerPoint presentation discussed a research project that is being conducted to identify conditions for producing stackable MFT deposits. The study is investigating various types and dosages of polymers and evaluating the degrees of MFT dilution and process configurations needed to maximize re-usable water recovery. Polymeric flocculants include AL-PAM and Magnafloc 1011. Settling tests have demonstrated that 50 ppm is the optimum dosage for both polymers when MFT is diluted to 5 wt percent solids, while 75 ppm of AL-PAM and 100 ppm of MF1011 are optimum dosages for MFT diluted to 10 wt percent solids. A novel supernatant filtration method was then used to produce filtration cakes and water. The study showed that the supernatant can be used to further dilute the MFTs. tabs., figs.

Coconut oil enhances tomato carotenoid tissue accumulation compared to safflower oil in the Mongolian gerbil ( Meriones unguiculatus ).

Science.gov (United States)

Conlon, Lauren E; King, Ryan D; Moran, Nancy E; Erdman, John W

2012-08-29

Evidence suggests that monounsaturated and polyunsaturated fats facilitate greater absorption of carotenoids than saturated fats. However, the comparison of consuming a polyunsaturated fat source versus a saturated fat source on tomato carotenoid bioaccumulation has not been examined. The goal of this study was to determine the influence of coconut oil and safflower oil on tomato carotenoid tissue accumulation in Mongolian gerbils ( Meriones unguiculatus ) fed a 20% fat diet. Coconut oil feeding increased carotenoid concentrations among many compartments including total carotenoids in the serum (p = 0.0003), adrenal glandular phytoene (p = 0.04), hepatic phytofluene (p = 0.0001), testicular all-trans-lycopene (p = 0.01), and cis-lycopene (p = 0.006) in the prostate-seminal vesicle complex compared to safflower oil. Safflower oil-fed gerbils had greater splenic lycopene concentrations (p = 0.006) compared to coconut oil-fed gerbils. Coconut oil feeding increased serum cholesterol (p = 0.0001) and decreased hepatic cholesterol (p = 0.0003) compared to safflower oil. In summary, coconut oil enhanced tissue uptake of tomato carotenoids to a greater degree than safflower oil. These results may have been due to the large proportion of medium-chain fatty acids in coconut oil, which might have caused a shift in cholesterol flux to favor extrahepatic carotenoid tissue deposition.

Low-temperature pyrolysis of oily sludge: roles of Fe/Al-pillared bentonites

Directory of Open Access Journals (Sweden)

Jia Hanzhong

2017-09-01

Full Text Available Pyrolysis is potentially an effective treatment of oily sludge for oil recovery, and the addition of a catalyst is expected to affect its pyrolysis behavior. In the present study, Fe/Al-pillared bentonite with various Fe/Al ratios as pyrolysis catalyst is prepared and characterized by XRD, N2 adsorption, and NH3-TPD. The integration of Al and Fe in the bentonite interlayers to form pillared clay is evidenced by increase in the basal spacing. As a result, a critical ratio of Fe/Al exists in the Fe/Al-pillared bentonite catalytic pyrolysis for oil recovery from the sludge. The oil yield increases with respect to increase in Fe/Al ratio of catalysts, then decreases with further increasing of Fe/Al ratio. The optimum oil yield using 2.0 wt% of Fe/Al 0.5-pillared bentonite as catalyst attains to 52.46% compared to 29.23% without catalyst addition in the present study. In addition, the addition of Fe/Al-pillared bentonite catalyst also improves the quality of pyrolysis-produced oil and promotes the formation of CH4. Fe/Al-pillared bentonite provides acid center in the inner surface, which is beneficial to the cracking reaction of oil molecules in pyrolysis process. The present work implies that Fe/Al-pillared bentonite as addictive holds great potential in industrial pyrolysis of oily sludge.

Effects of tallow, choice white grease, palm oil, corn oil, or soybean oil on apparent total tract digestibility of minerals in diets fed to growing pigs.

Science.gov (United States)

Merriman, L A; Walk, C L; Parsons, C M; Stein, H H

2016-10-01

An experiment was conducted to determine the effect of supplementing diets fed to growing pigs with fat sources differing in their composition of fatty acids on the apparent total tract digestibility (ATTD) of minerals. A diet based on corn, potato protein isolate, and 7% sucrose was formulated. Five additional diets that were similar to the previous diet with the exception that sucrose was replaced by 7% tallow, choice white grease, palm oil, corn oil, or soybean oil were also formulated. Diets were formulated to contain 0.70% Ca and 0.33% standardized total tract digestible P. Growing barrows ( = 60; 15.99 ± 1.48 kg initial BW) were allotted to a randomized complete block design with 2 blocks of 30 pigs, 6 dietary treatments, and 10 replicate pigs per treatment. Experimental diets were provided for 12 d with the initial 5 d being the adaptation period. Total feces were collected for a 5-d collection period using the marker-to-marker approach, and the ATTD of minerals, ether extract, and acid hydrolyzed ether extract was calculated for all diets. Digestibility of DM was greater ( soybean oil compared with the diet containing choice white grease or the basal diet, with all other diets being intermediate. The ATTD of Ca, S, and P was greater ( soybean oil, corn oil, palm oil, or tallow than for pigs fed the basal diet or the diet containing choice white grease. The ATTD of Mg, Zn, Mn, Na, and K were not different among dietary treatments. The ATTD of ether extract was greater ( oil, corn oil, or soybean oil compared with the diet containing choice white grease, and the ATTD of acid hydrolyzed ether extract in the diet containing soybean oil was also greater ( oil, corn oil, or soybean oil may increase the ATTD of some macrominerals, but that appears not to be the case if choice white grease is used. There was no evidence of negative effects of the fat sources used in this experiment on the ATTD of any minerals.

Transesterification of rapeseed oil for biodiesel production in trickle-bed reactors packed with heterogeneous Ca/Al composite oxide-based alkaline catalyst.

Science.gov (United States)

Meng, Yong-Lu; Tian, Song-Jiang; Li, Shu-Fen; Wang, Bo-Yang; Zhang, Min-Hua

2013-05-01

A conventional trickle bed reactor and its modified type both packed with Ca/Al composite oxide-based alkaline catalysts were studied for biodiesel production by transesterification of rapeseed oil and methanol. The effects of the methanol usage and oil flow rate on the FAME yield were investigated under the normal pressure and methanol boiling state. The oil flow rate had a significant effect on the FAME yield for the both reactors. The modified trickle bed reactor kept over 94.5% FAME yield under 0.6 mL/min oil flow rate and 91 mL catalyst bed volume, showing a much higher conversion and operational stability than the conventional type. With the modified trickle bed reactor, both transesterification and methanol separation could be performed simultaneously, and glycerin and methyl esters were separated additionally by gravity separation. Copyright © 2013 Elsevier Ltd. All rights reserved.

Source identification of beached oil at Al Zubarah, Northwestern Qatar

DEFF Research Database (Denmark)

Al-Kaabi, Nasser S.; Kristensen, Mette; Zouari, Nabil

2017-01-01

compounds for these spill samples were compared to those of more than 250 crude oils from around the world applying the CHEMSIC method (chemometric analysis of selected ion chromatograms). The weathering degree varied significantly between samples, and relatively unweathered oil from the Gulf War oil spill...

Distillation Time as Tool for Improved Antimalarial Activity and Differential Oil Composition of Cumin Seed Oil.

Science.gov (United States)

Zheljazkov, Valtcho D; Gawde, Archana; Cantrell, Charles L; Astatkie, Tess; Schlegel, Vicki

2015-01-01

A steam distillation extraction kinetics experiment was conducted to estimate essential oil yield, composition, antimalarial, and antioxidant capacity of cumin (Cuminum cyminum L.) seed (fruits). Furthermore, regression models were developed to predict essential oil yield and composition for a given duration of the steam distillation time (DT). Ten DT durations were tested in this study: 5, 7.5, 15, 30, 60, 120, 240, 360, 480, and 600 min. Oil yields increased with an increase in the DT. Maximum oil yield (content, 2.3 g/100 seed), was achieved at 480 min; longer DT did not increase oil yields. The concentrations of the major oil constituents α-pinene (0.14-0.5% concentration range), β-pinene (3.7-10.3% range), γ-cymene (5-7.3% range), γ-terpinene (1.8-7.2% range), cumin aldehyde (50-66% range), α-terpinen-7-al (3.8-16% range), and β-terpinen-7-al (12-20% range) varied as a function of the DT. The concentrations of α-pinene, β-pinene, γ-cymene, γ-terpinene in the oil increased with the increase of the duration of the DT; α-pinene was highest in the oil obtained at 600 min DT, β-pinene and γ-terpinene reached maximum concentrations in the oil at 360 min DT; γ-cymene reached a maximum in the oil at 60 min DT, cumin aldehyde was high in the oils obtained at 5-60 min DT, and low in the oils obtained at 240-600 min DT, α-terpinen-7-al reached maximum in the oils obtained at 480 or 600 min DT, whereas β-terpinen-7-al reached a maximum concentration in the oil at 60 min DT. The yield of individual oil constituents (calculated from the oil yields and the concentration of a given compound at a particular DT) increased and reached a maximum at 480 or 600 min DT. The antimalarial activity of the cumin seed oil obtained during the 0-5 and at 5-7.5 min DT timeframes was twice higher than the antimalarial activity of the oils obtained at the other DT. This study opens the possibility for distinct marketing and utilization for these improved oils. The antioxidant

Hydrodeoxygenation of Pyrolysis Bio-Oil Over Ni Impregnated Mesoporous Materials.

Science.gov (United States)

Lee, In-Gu; Lee, Heejin; Kang, Bo Sung; Kim, Young-Min; Kim, Sang Chai; Jung, Sang-Chul; Ko, Chang Hyun; Park, Young-Kwon

2018-02-01

The catalytic hydrodeoxygenation (HDO) of bio-oil over Ni-supported mesoporous materials was performed using a high pressure autoclave reactor. The actual pyrolysis oil of cork oak wood was used as a sample, and Ni/Al-SBA-15 and Ni/Al-MSU-F were used as catalysts. In addition, supercritical ethanol was added as solvent. Both Ni-supported mesoporous catalysts showed efficient HDO reaction ability. A higher heating value and pH of bio-oil were achieved by the HDO reaction over both catalysts and upgraded bio-oil had a lower viscosity. Compared to Ni/Al-MSU-F, Ni/Al- SBA-15 produced more upgraded bio-oil with a lower oxygen content and higher heating value via a catalytic HDO process.

Water-in-oil emulsions results of formation studies and applicability to oil spill modelling

International Nuclear Information System (INIS)

Fingas, Merv; Fieldhouse, Ben; Mullin, Joe

1999-01-01

This paper summarises studies of water-in-oil emulsions, their stability, and modelling of their formation. Studies show that water-in-oil emulsions might be characterised into three categories (stable, mesostable and unstable). These categories were established by visual appearance, elasticity and viscosity difference. It was also shown that water content was not an important factor. A fourth category of water-in-oil exists, that of water entrainment, which is not an emulsion. Water-in-oil emulsions made from crude oils have different classes of stabilities as a result of the asphaltene and resin contents. The differences in the emulsion types are readily distinguished both by their rheological properties, and simply by appearance. The apparent viscosity of a stable emulsion at a shear rate of one reciprocal second, is at least three orders-of-magnitude greater than the starting oil. An unstable emulsion usually has a viscosity no more than one order-of-magnitude greater than that of the starting oil. A stable emulsion has a significant elasticity, whereas an unstable emulsion does not. Stable emulsions have sufficient asphaltenes (>∼7%) to establish films of these compounds around water droplets. Mesostable emulsions have insufficient asphaltenes to render them completely stable. Stability is achieved by visco-elastic retention of water and secondarily by the presence of asphaltene or resin films. Mesostable emulsions display apparent viscosities of about 80-600 times that of the starting oil and true viscosities of 20-200 times that of the starting oil. Mesostable emulsions have an asphaltene and resin content greater than 3%. Entrained water occurs when a viscous oil retains larger water droplets, but conditions are not suitable for the formation of an emulsion. Entrained water may have a viscosity that is similar or slightly greater (∼ 2-10 times) than the starting oil. It was found that emulsion formation occurs at a threshold energy, however this energy

Productions of sunflower oil biodiesel and used cooking oil through heterogeneous catalysts compared to conventional homogeneous catalysts

International Nuclear Information System (INIS)

Gutiérrez-Zapata, C A; Collazos, C A; Acuña, H E Castellanos; Fernandez, C P; Martínez, D Blanco; Cuervo, J A

2017-01-01

This document compares homogeneous and heterogeneous catalysts used by production of biodiesel of sunflower oil and cooking oil used in frying. For this, NaOH was used as a catalyst homogeneous, and K 2 CO 3 and Na 2 CO 3 supported in gamma-alumina (K 2 CO 3 /γ Al 2 O 3 y Na 2 CO 3 /γ-Al 2 O 3 ) were synthesized as heterogeneous catalysts, which were characterized by X-ray diffraction. The transesterification tests were carried out for the sunflower oil and used cooking oil, in a reflux system, to different molar relations methanol/oil, depending on the type of oil and characterization of the same. The reflux system is performed at a temperature of 55-60°C for one hour. Finally, biofuel was characterized and the yield of the reaction was calculated. (paper)

Productions of sunflower oil biodiesel and used cooking oil through heterogeneous catalysts compared to conventional homogeneous catalysts

Science.gov (United States)

Gutiérrez-Zapata, C. A.; Blanco Martínez, D.; Collazos, C. A.; Castellanos Acuña, H. E.; Cuervo, J. A.; Fernandez, C. P.

2017-01-01

This document compares homogeneous and heterogeneous catalysts used by production of biodiesel of sunflower oil and cooking oil used in frying. For this, NaOH was used as a catalyst homogeneous, and K2CO3 and Na2CO3 supported in gamma-alumina (K2CO3/γ Al2O3 y Na2CO3 /γ-Al2O3) were synthesized as heterogeneous catalysts, which were characterized by X-ray diffraction. The transesterification tests were carried out for the sunflower oil and used cooking oil, in a reflux system, to different molar relations methanol/oil, depending on the type of oil and characterization of the same. The reflux system is performed at a temperature of 55-60°C for one hour. Finally, biofuel was characterized and the yield of the reaction was calculated.

Exocrine pancreatic secretion is stimulated in piglets fed Fish oil compared with those fed Coconut Oil or Lard

DEFF Research Database (Denmark)

Hedemann, Mette Skou; Pedersen, Asger Roer; Engberg, Ricarda M.

2001-01-01

An experiment was conducted to study the effect of feeding diets containing fat sources with different fatty acid composition (fish oil, coconut oil or lard, 10 g/100 g diet) on exocrine pancreatic secretion in piglets after weaning. A total of 16 barrows were weaned at 4 wk of age; 3 d later...... the coconut oil or lard diets. The output [U/(h. kg(0.75))] of lipase was higher in piglets fed fish oil than in piglets fed lard or coconut oil. The output of colipase was greater in piglets fed fish oil and coconut oil than in those fed lard. The dietary treatments did not affect the output of carboxylester...... hydrolase. The output of trypsin was significantly lower in piglets fed lard than in piglets fed fish oil or coconut oil diets and the output of carboxypeptidase B was greater in those fed the fish oil diet. Protein, chymotrypsin, carboxypeptidase A, elastase and amylase outputs did not differ among...

Synthesis of H/Bentonite and Ni/Al2O3-bentonite and its application to produce biogasoline from nyamplung seed (Calophyllum inophillum Linn) oil by catalytic hydrocracking

Science.gov (United States)

Marini, A. T.; Wijaya, K.; Sasongko, N. A.

2018-03-01

Hydrocracking process of Nyamplung (Calophyllum inophillum Linn) seed oil to produce biogasoline using H/bentonite and Ni/Al2O3-bentonite that pillared by Al2O3 as catalyst had been conducted. Bentonite was activated by acidification using HF 1% and H2SO4 0.5 M. Ni metal was impregnated into bentonite with two steps reaction; therewas intercalation with Al2O3kegging ion and Ni metal impregnation using NiCl2 metal salt. Catalysts were characterized by infrared spectrophotometer (FTIR), X-ray diffraction (XRD), X-ray fluorescence (XRF), BET, TEM and ammonia adsorption. Hydrocracking reaction was variated by Ni/Al2O3-bentonite and H/bentonite with ratio catalyst/oil 1:100. Biocrude was prepared by extraction by using ethanol 96%. Hydrocracking oil products were further analyzed by GC-MS. The results show that the acidity of bentonite by activation using HF 1% and H2SO4 0.5 M has been increased from 62.58 to 64.62 mmol/g. Impregnation process also increased the acidity of bentonite from 62.58 to 64.89 mmol/g. Activation using HF 1% and H2SO4 0.5 M, intercalation by Al2O3 and impregnation by Ni metal were increasing the crystallinity, surface area, total volume pore and average pore size of bentonite. These techniques were also causeddealumination of bentonite. The hydrocracking process successfully synthesized hydrocarbons with a number of carbon chain between C5-C20 which include bio-gasoline group compounds. Moreover, catalytic processes by H/bentonite and Ni/Al2O3-bentonite also successfully produced 39.83% and 60.37% of biogasoline yields, respectively.

Sorption of oil in the polyurethane from oil or castor oil; Sorcao de oleo no poliuretano derivado do petroleo ou do oleo de mamona

Energy Technology Data Exchange (ETDEWEB)

Florentino, Wagner M; Goulart, Shane A.S.; Mulinari, Daniella R. [Centro Universitario de Volta Redonda (UniFOA), Volta Redonda, RJ (Brazil)], e-mail: wagner-can@hotmail.com

2011-07-01

The oil outpouring has caused serious environmental problems. To minimize this damage polyurethane foams have been used. In this work, the use of polyurethane from oil and castor oil, in different polyol/diisocyanate mass ratios, to absorb oil was evaluated. Results revealed that the proportion of polyol and diisocyanate influenced in the sorption capacity and the polyurethane from castor oil presented greater sorption capacity. Of this way, can say that the polyurethane from oil can be replaced by castor oil, contributing to sustainable development. (author)

"ALS reversals": demographics, disease characteristics, treatments, and co-morbidities.

Science.gov (United States)

Harrison, Daniel; Mehta, Paul; van Es, Michael A; Stommel, Elijah; Drory, Vivian E; Nefussy, Beatrice; van den Berg, Leonard H; Crayle, Jesse; Bedlack, Richard

2018-04-02

To identify differences in demographics, disease characteristics, treatments, and co-morbidities between patients with "amyotrophic lateral sclerosis (ALS) reversals" and those with typically progressive ALS. Cases of possible ALS reversals were found in prior publications, in the Duke ALS clinic, through self-referral or referral from other Neurologists, and on the internet. Of 89 possible reversals identified, 36 cases were included because chart or literature review confirmed their diagnosis and a robust, sustained improvement in at least one objective measure. Controls were participants in the Pooled Resource Open-Access ALS Clinical Trials database and the National ALS Registry. Cases and controls were compared using descriptive statistics. ALS reversals were more likely to be male, have limb onset disease, and initially progress faster. The prevalences of myasthenia gravis (MG) and purely lower motor neuron disease in cases were higher than estimates of these prevalences in the general population. The odds of taking curcumin, luteolin, cannabidiol, azathioprine, copper, glutathione, vitamin D, and fish oil were greater for cases than controls. When compared to patients with typically progressive ALS, patients with reversals differed in their demographics, disease characteristics, and treatments. While some of these patients may have had a rare antibody-mediated ALS mimicker, such as atypical myasthenia gravis, details of their exams, EMGs and family histories argue that this was unlikely. Instead, our data suggest that ALS reversals warrant evaluation for mechanisms of disease resistance and that treatments associated with multiple ALS reversals deserve further study.

Oil shale commercialization study

Energy Technology Data Exchange (ETDEWEB)

Warner, M.M.

1981-09-01

Ninety four possible oil shale sections in southern Idaho were located and chemically analyzed. Sixty-two of these shales show good promise of possible oil and probable gas potential. Sixty of the potential oil and gas shales represent the Succor Creek Formation of Miocene age in southwestern Idaho. Two of the shales represent Cretaceous formations in eastern Idaho, which should be further investigated to determine their realistic value and areal extent. Samples of the older Mesozonic and paleozoic sections show promise but have not been chemically analyzed and will need greater attention to determine their potential. Geothermal resources are of high potential in Idaho and are important to oil shale prospects. Geothermal conditions raise the geothermal gradient and act as maturing agents to oil shale. They also might be used in the retorting and refining processes. Oil shales at the surface, which appear to have good oil or gas potential should have much higher potential at depth where the geothermal gradient is high. Samples from deep petroleum exploration wells indicate that the succor Creek shales have undergone considerable maturation with depth of burial and should produce gas and possibly oil. Most of Idaho's shales that have been analyzed have a greater potential for gas than for oil but some oil potential is indicated. The Miocene shales of the Succor Creek Formation should be considered as gas and possibly oil source material for the future when technology has been perfectes. 11 refs.

State of the Art Satellite and Airborne Marine Oil Spill Remote Sensing: Application to the BP Deepwater Horizon Oil Spill

Science.gov (United States)

2012-01-01

development and operationalization of new spill response remote sensing tools must precede the next major oil spill. © 2012 Elsevier Inc. All rights reserved...Environment 124 (2012) 185–209 sensing oil spill impacts, and 5) a final discussion. Each section presents background, available remote sensing tools , and...cialized DaVinci command-line software (Clark et al., 2003) then mapped oil slick volume (Clark et al., 2010) in each AVIRIS pixel by identifying the

Competitiveness of ALS inhibitors resistant and susceptible biotypes of Greater Beggarticks (Bidens subalternans Competitividade de biótipos de Picão-Preto (Bidens subalternans Resistente e euscetível aos inibidores da ALS

Directory of Open Access Journals (Sweden)

F.P. Lamego

2011-06-01

Full Text Available The continuous use of ALS-inhibiting herbicides has led to the evolution of herbicide-resistant weeds worldwide. Greater beggarticks is one of the most troublesome weeds found in the soybean production system in Brazil. Recently, a greater beggarticks biotype that is resistant (R to ALS inhibitors due to Trp574Leu mutation in the ALS gene was identified. Also, the adaptive traits between susceptible (S and R to ALS inhibitors biotypes of greater beggarticks were compared. Specifically, we aimed to: (1 evaluate and compare the relative growth rates (RGR between the biotypes; (2 analyze the seed germination characteristics of R and S biotypes under different temperature conditions; and (3 evaluate their competitive ability in a replacement series study. The experiments were conducted at the University of Arkansas, USA, in 2007 and at Universidade Federal do Rio Grande do Sul (Federal University of Rio Grande do Sul, Brazil, in 2008. Plant proportions for replacement series studies were respectively 100:0, 75:25, 50:50, 25:75 and 0:100, with a total population of 150 plants m-2. There was no difference in RGR between R and S biotypes. The R-biotype germination rate was lower than that of the S biotype. However, at low temperature conditions (15 ºC, the reverse was observed. In general, there is no difference in the competitive ability between R and S greater beggarticks biotypes.O uso contínuo de herbicidas inibidores da ALS tem levado à evolução de plantas daninhas resistentes mundialmente. Picão-preto é uma das mais importantes plantas daninhas no sistema de produção de soja no Brasil. Recentemente, foi identificado um biótipo de picao-preto resistente (R aos inibidores da ALS devido à mutação Trp574Leu no gene ALS. Também, foram comparadas características adaptativas entre biótipos de picao-preto suscetível (S e R aos inibidores da ALS. Especificamente, os objetivos deste trabalho foram: (1 avaliar e comparar o crescimento

Chemical profiling of gaharu oil

International Nuclear Information System (INIS)

Mat Rasol Awang; Mohd Fajri Osman; Ahsanulkhaliqin Abd Wahab; Khairuddin Abdul Rahim; Shaiful Azuar Mohamad

2006-01-01

Gaharu oil from Aquilaria agallocha and Aquilaria malaccensis Lamk has been reported to contain different phytochemicals components (Ishihara et al., 1993). There are also differences reported by gaharu oil suppliers. The differences suggested they originate from varied of sources of gaharu wood, oleoresin maturity and extraction technology employed. In this study, gaharu oil purchased from different sources were initially analysed and later cross-examined against chemical components of oil extracted from wood sources systematically graded. The gaharu oil components obtained from this work will be presented and discussed. Initiative to profile oil provides impetus to database development and standardisation of gaharu oil. (Author)

Neutron activation analysis of trace metallic elements eluted from molecular sieves in the dehydration process of safflower oil

International Nuclear Information System (INIS)

Takasago, Masahisa; Kobayashi, Koichi; Taru, Yasunori; Takaoka, Kyo

1992-01-01

Dissolved water in safflower oil affects the autoxidation of this oil significantly. Molecular sieves were used to remove the dissolved water from the oil. This method is much simpler than that of distillation, and dissolved water can be removed to the same extent as that by distillation. But, due to the elution of many kinds of trace metallic elements in the oil dehydrated with molecular sieves, these elements were analyzed by neutron activation analysis. For a data comparison trace amounts of metallic elements in the oil dehydrated by distillation were also analyzed. Since the intensity of the γ ray-photoelectric peak of nuclide 28 Al was largest among the detected elements, this element was analyzed quantitatively and the other elements qualitatively. In safflower oil dehydrated with molecular sieves, 14 kinds of the elements (I, Br, Al, Mg, Si, V, Cl, Nd, Ta, Cr, Sb, Cs, Co, Na) were detected. Also, I, Br, Cl, Cr, Ta, Sb, and Al elements were detected in the oil dehydrated by distillation. The intensity of the photoelectric peak of nuclide except 28 Al was essentially the same as that in the oil dehydrated by distillation, but the intensity of 28 Al in the oil with molecular sieves was about 28 times stronger than that in distillation oil. In the molecular sieves, 19 impure elements in addition to the original constituents (Na, K, Al, si, O) were detected. It was Al, Na, Si, Nd, Cs, and Co along with impure elements may possibly have been eluted in the oil. Al element in safflower oil dehydrated with molecular sieves was analyzed quantitatively. 0.91 ppm of Al was detected in safflower oil. The eluted amount of Al in safflower oil dehydrated by distillation was 0.032 ppm. A larger amount of Al element was thus eluted into the oil dehydrated with molecular sieves than by distillation. (author)

Analysis of physical characteristics of vegetable oils

Energy Technology Data Exchange (ETDEWEB)

Piamba Tulcan, Oscar Edwin [Universidade Nacional da Colombia (UNAL), Bogota (Colombia). Fac. de Ingenieria; Universidade Federal Fluminense (PGMEC/UFF), Niteroi, RJ (Brazil). Programa de Pos-Graduacao em Engenharia Mecanica], E-mail: oepiambat@unal.edu.co; Andrade, Danielle Oliveira de; Andrade, Ednilton Tavares de [Universidade Federal Fluminense (TER/UFF), Niteroi, RJ (Brazil). Dept. de Engenharia Agricola e do Meio Ambiente; Pereira, Roberto Guimaraes [Universidade Federal Fluminense (TER/UFF), Niteroi, RJ (Brazil). Dept. de Engenharia Mecanica

2008-07-01

Different vegetable oils were characterized using standardized methods. The evaluated characteristics were density, viscosity, flow point, cloud point and corrosion. The obtained data was tabulated and compared with average composition values of oils in percentage of fatty acids and iodine number for each oil. In this analysis it is shown that viscosity decreases with the increase of the iodine number, and density decrease. The cloud and flow point have greater relation with the presence of saturated or highly unsaturated fatty acids, respectively. The index of corrosion is greater when oil saturation or its iodine number are increased. (author)

Biodiesel production from soybean oil and methanol using hydrotalcites as catalyst

Energy Technology Data Exchange (ETDEWEB)

Silva, Carla Cristina C.M.; Aranda, Donato A.G. [GREENTEC - Laboratory of Green Technologies, Escola de Quimica, Universidade Federal do Rio de Janeiro (UFRJ), Centro de Tecnologia, Bloco E, sala 211, CEP 21941-909, Rio de Janeiro, RJ (Brazil); Ribeiro, Nielson F.P.; Souza, Mariana M.V.M. [LabTecH - Laboratory of Hydrogen Technologies, Escola de Quimica/UFRJ, Centro de Tecnologia, Bloco E, sala 206, CEP 21941-909, Rio de Janeiro, RJ (Brazil)

2010-02-15

Esters of fatty acids, derived from vegetable oils or animal fats, and known as biodiesel, are a promising alternative diesel fuel regarding the limited resources of fossil fuels and the environmental concerns. In this work, methanolysis of soybean oil was investigated using Mg-Al hydrotalcites as heterogeneous catalyst, evaluating the effect of Mg/Al ratio on the basicity and catalytic activity for biodiesel production. The catalysts were prepared with Al/(Mg + Al) molar ratios of 0.20, 0.25 and 0.33, and characterized by X-ray diffraction (XRD), textural analysis (BET method) and temperature-programmed desorption of CO{sub 2} (CO{sub 2}-TPD). When the reaction was carried out at 230 C with a methanol:soybean oil molar ratio of 13:1, a reaction time of 1 h and a catalyst loading of 5 wt.%, the oil conversion was 90% for the sample with Al/(Mg + Al) ratio of 0.33. This sample was the only one to show basic sites of medium strength. We also investigated the reuse of this catalyst, the effect of calcination temperature and made a comparison between refined and acidic oil. (author)

Future of oil and gas

International Nuclear Information System (INIS)

Gatermann, R.; Ten Hoedt, R.

2009-01-01

Two articles in the section 'Future of oil and gas': one ('Baltic strained by oil traffic') on the growing risks of accidents in maritime traffic in the Baltic region, and one ('Angola wants bigger piece of the pie') on the importance of the oil production in Angola to energy supplies in Europe and the USA. It appears that national oil company Sonango wants to have a greater part of the profits

The Gothic shale of the Pennsylvanian Paradox Formation Greater Aneth Field (Aneth Unit) Southeastern Utah U.S.A.: Seal for Hydrocarbons and Carbon Dioxide Storage.

Energy Technology Data Exchange (ETDEWEB)

Heath, Jason E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Dewers, Thomas [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Chidsey, Thomas C. [Utah Geoglogical Survey, Salt Lake City, UT (United States); Carney, Stephanie M. [Utah Geoglogical Survey, Salt Lake City, UT (United States); Bereskin, S. R. [Bereskin and Associates, Salt Lake City (United States)

2017-05-01

Greater Aneth oil field, Utah’s largest oil producer, was discovered in 1956 and has produced over 483 million barrels of oil. Located in the Paradox Basin of southeastern Utah, Greater Aneth is a stratigraphic trap producing from the Pennsylvanian (Desmoinesian) Paradox Formation. Because Greater Aneth is a mature, major oil field in the western U.S., and has a large carbonate reservoir, it was selected to demonstrate combined enhanced oil recovery and carbon dioxide storage. The Aneth Unit in the northwestern part of the field has produced over 160 million barrels of the estimated 386 million barrels of original oil in place—a 42% recovery rate. The large amount of remaining oil made the Aneth Unit ideal to enhance oil recovery by carbon dioxide flooding and demonstrate carbon dioxide storage capacity.

Neutron activation analysis of trace metallic elements eluted from molecular sieves in the dehydration process of safflower oil

Energy Technology Data Exchange (ETDEWEB)

Takasago, Masahisa; Kobayashi, Koichi; Taru, Yasunori; Takaoka, Kyo (Musashi Inst. of Tech., Tokyo (Japan))

1992-11-01

Dissolved water in safflower oil affects the autoxidation of this oil significantly. Molecular sieves were used to remove the dissolved water from the oil. This method is much simpler than that of distillation, and dissolved water can be removed to the same extent as that by distillation. But, due to the elution of many kinds of trace metallic elements in the oil dehydrated with molecular sieves, these elements were analyzed by neutron activation analysis. For a data comparison trace amounts of metallic elements in the oil dehydrated by distillation were also analyzed. Since the intensity of the [gamma] ray-photoelectric peak of nuclide [sup 28]Al was largest among the detected elements, this element was analyzed quantitatively and the other elements qualitatively. In safflower oil dehydrated with molecular sieves, 14 kinds of the elements (I, Br, Al, Mg, Si, V, Cl, Nd, Ta, Cr, Sb, Cs, Co, Na) were detected. Also, I, Br, Cl, Cr, Ta, Sb, and Al elements were detected in the oil dehydrated by distillation. The intensity of the photoelectric peak of nuclide except [sup 28]Al was essentially the same as that in the oil dehydrated by distillation, but the intensity of [sup 28]Al in the oil with molecular sieves was about 28 times stronger than that in distillation oil. In the molecular sieves, 19 impure elements in addition to the original constituents (Na, K, Al, si, O) were detected. It was Al, Na, Si, Nd, Cs, and Co along with impure elements may possibly have been eluted in the oil. Al element in safflower oil dehydrated with molecular sieves was analyzed quantitatively. 0.91 ppm of Al was detected in safflower oil. The eluted amount of Al in safflower oil dehydrated by distillation was 0.032 ppm. A larger amount of Al element was thus eluted into the oil dehydrated with molecular sieves than by distillation. (author).

HDN and HDS of different gas oils derived from Athabasca bitumen over phosphorus-doped NiMo/{gamma}-Al{sub 2}O{sub 3} carbides

Energy Technology Data Exchange (ETDEWEB)

Sundaramurthy, V.; Dalai, A.K. [Catalysis and Chemical Reaction Engineering Laboratories, Department of Chemical Engineering, University of Saskatchewan, Saskatoon, Sask. S7N 5A9 (Canada); Adjaye, J. [Syncrude Edmonton Research Centre, Edmonton, Alta. T6N 1H4 (Canada)

2006-10-26

A series of phosphorous-doped {gamma}-Al{sub 2}O{sub 3} supported Ni-Mo bimetallic carbide catalysts (PNiMo{sub 2}C/Al{sub 2}O{sub 3}) with 0-4.5wt.% Ni, 13wt.% Mo and 2.5wt.% P were synthesized and characterized by elemental analysis, pulsed CO chemisorption, surface area measurement, X-ray diffraction (XRD), near-edge X-ray absorption fine structure (NEXAFS), DRIFT spectroscopy of CO adsorption and H{sub 2} temperature programmed reduction. XRD indicated the formation of pure {beta}-Mo{sub 2}C phase in these catalysts, whereas the near edge X-ray absorption fine structure of C K-edge confirmed the formation of carbidic carbons. DRIFT spectra of adsorbed CO revealed that Ni or P addition to Mo{sub 2}C/Al{sub 2}O{sub 3} catalyst not only increases the number of surface Mo sites, but also promotes the reducibility of Mo. The partial sulfidation of Mo{sub 2}C phase in the presence of H{sub 2}S/H{sub 2} gas mixture at 370{sup o}C was evidenced by DRIFTS of adsorbed CO. The HDN and HDS activities of these PNiMo{sub 2}C/Al{sub 2}O{sub 3} catalysts were performed in a trickle bed reactor using light gas oil (LGO) and heavy gas oil (HGO) derived from Athabasca bitumen at 8.8MPa and compared with the unpromoted Mo carbide (Mo{sub 2}C/Al{sub 2}O{sub 3}), P doped Mo carbide (PMo{sub 2}C/Al{sub 2}O{sub 3}) and Ni promoted Mo carbide (NiMo{sub 2}C/Al{sub 2}O{sub 3}). The P doped Ni-Mo bimetallic carbide catalysts showed enhanced HDN activity compared to the Mo{sub 2}C/Al{sub 2}O{sub 3}, NiMo{sub 2}C/Al{sub 2}O{sub 3} and PMo{sub 2}C/Al{sub 2}O{sub 3} catalysts. The maximum N and S conversions, respectively, were obtained over PNiMo{sub 2}C/Al{sub 2}O{sub 3} and NiMo{sub 2}C/Al{sub 2}O{sub 3} catalysts containing 2.5wt.% Ni. (author)

Offshore oil spill recovery operations in the Persian Gulf

International Nuclear Information System (INIS)

Williams, H.D.; Gangsaas, G.K.

1993-01-01

On or about January 25, 1991, Iraqi forces in Kuwait discharged more than 4 million barrels of Kuwait crude oil into the Persian Gulf. The counterclockwise current carried the resulting slick southeastward along the coast of Saudi Arabia. The Saudi Arabian oil company, Aramco, chartered the multiclassed tanker and response vessel Al Waasit, based in Dubai, to assist in the offshore recovery operation. The Al Waasit's response resulted in the offshore recovery of about 100,000 barrels of oil during a 42-day period, without a recovery system failure. The authors both served on board Al Waasit as operations managers during this response operation

THE INFLUENCE OF Pd IMPREGNATION INTO Al-MCM-41 ON THE CHARACTERS AND ACTIVITY FOR BIOGASOLINE PRODUCTION BY CATALYTIC HYDROCRACKING OF FAMEs FROM NYAMPLUNG SEED OIL (Calophyllum Inophyllum

Directory of Open Access Journals (Sweden)

Hendro Juwono

2013-08-01

Full Text Available Biogasoline have been synthesized through catalytic hydrocracking reaction against FAMEs compounds (fatty acid methyl esters obtained from the transesterification of Nyamplung seed oil. The performance of Al-MCM-41 and Pd/Al-MCM-41 as the catalytic hydrocracking was compared. In this research, the influence of Pd impregnation into Al-MCM-41 catalyst on the characters and catalytic activity has been evaluated. The characters determined were crystallinity by using X-Ray Diffractometer (XRD, Si/Al ratio by Inductively Coupled Plasma (ICP, the acidity by pyridine adsorption, the surface area and pore volume by surface area analyzer and the morphology by Scanning Electron Microscopy (SEM. Catalytic activity was examined for hydrocracking of free fatty acid methyl esters (FAMEs produced from the transesterification of Nyamplung seed oil, by Hydrogen flowing. The research result showed that impregnation of Pd into Al-MCM-41 has been successfully carried out, which did not destroy the structural morphology of the catalyst. It was also discovered that the Pd impregnation could increase Si/Al ratio and the acidity but it leads to decrease in the catalyst surface area and the volume. Furthermore, Pd impregnated Al-MCM-41 showed superior activity compared to Al-MCM-41 for FAMEs hydrocracking. The superiority was indicated by higher effectiveness and yields selectiveness, that were 100% hydrocarbon composed of C9-C18 that was dominated by C12 emerging the gasoline fraction, compared of that by the results used Al-MCM-41 catalyst that were 97% hydrocarbon consisted of C8-C20 with equal abundance.

Combined numerical and experimental determination of the convective heat transfer coefficient between an AlCrN-coated Vanadis 4 tool and Rhenus oil

DEFF Research Database (Denmark)

Üstünyagiz, Esmeray; Nielsen, Chris V.; Tiedje, Niels S.

2018-01-01

Abstract Regardless of the field of application, the reliability of numerical simulations depends on correct description of boundary conditions. In thermal simulation, determination of heat transfer coefficients is important because it varies with material properties and process conditions....... This paper shows a combined experimental and numerical analysis applied for determination of the heat transfer coefficient between an AlCrN-coated Vanadis 4 tool and Rhenus LA722086 oil in an unloaded condition, i.e. without the tool being in contact with a workpiece. It is found that the heat transfer...... coefficient in unloaded conditions at 80°C oil temperature is 0.1 kW/(m2∙K) between the selected stamping tool and mineral oil. A sensitivity analysis of the numerical model was performed to verify the effects of mesh discretization, temperature measurement location and tool geometry. Among these parameters...

Phenolic compounds and sterol contents of olive (olea europaea l.) oils obtained from different

International Nuclear Information System (INIS)

Juhaimi, F.; Ghafoor, K.; Adiamo, O.Q.; Babiker, E.E.

2017-01-01

Oil obtained from 5 different olive cultivars was analyzed for phenolic and sterol composition. Total phenolic contents of oils were determined between 94.99 mg GAE/kg oil (Al-Joif) to 405.71 mg GAE/ kg oil (Sariulak) (p<0.05). Phenolic compounds of oils obtained from different olive verities (Ayvalik, Sariulak, Savrani, Al-Joif and Gemlik) when fully ripened were evaluated using reversed phase high performance liquid chromatography (RP-HPLC). Hydroxytyrosol and tyrosol were identified to have higher concentrations than other compounds. Tyrosol contents were between 3.65 mg/kg to 21.47 mg/kg oil (p<0.05) in different verities. The contents of hydroxytyrosol of oils for Ayvalik and Gemlik were 1.23 and 14.42 mg/kg, respectively. Cinnamic acid was detected only in Al-Joif olive oil sample. Low amounts of syringic, vanillin, p-cumaric, quercetin and luteolin were observed in different varieties' oils. (author)

Oil supply and oil politics: Deja Vu all over again

International Nuclear Information System (INIS)

Cleveland, Cutler J.; Kaufmann, Robert K.

2003-01-01

President Bush has identified US dependence on imported oil as an urgent energy, economic, and national security concern. The President's energy plan promotes the development of domestic resources, based on the assumption that economic incentives and the opening of frontier areas for exploration will increase domestic production. If realized, this will reduce dependence on imported oil and reduce OPEC's ability to affect aggregate oil supply and price. The evidence suggests, however, that this policy will not increase significantly US production of crude oil, will not reduce significantly OPEC's influence, and it will distort the US macroeconomy. Even if allowed, production from the Arctic National Wildlife Refuge will have a negligible impact on the world oil markets. Further subsidies to the oil industry will divert resources from other more productive investments. Conservation and energy efficiency merit greater emphasis in US energy policy given their ability to reduce the use of cost-effective and environmentally beneficial ways

Oil supply and oil politics: Deja Vu all over again

International Nuclear Information System (INIS)

Cleveland, C.J.; Kaufmann, R.K.

2003-01-01

President Bush has identified US dependence on imported oil as an urgent energy, economic, and national security concern. The President's energy plan promotes the development of domestic resources, based on the assumption that economic incentives and the opening of frontier areas for exploration will increase domestic production. If realized, this will reduce dependence on imported oil and reduce OPEC's ability to affect aggregate oil supply and price. The evidence suggests, however, that this policy will not increase significantly US production of crude oil, will not reduce significantly OPEC's influence, and it will distort the US macroeconomy. Even if allowed, production from the Arctic National Wildlife Refuge will have a negligible impact on the world oil markets. Further subsidies to the oil industry will divert resources from other more productive investments. Conservation and energy efficiency merit greater emphasis in US energy policy given their ability to reduce the use of cost-effective and environmentally beneficial ways. (author)

Control of ALS resistant volunteer oil seed rape and other dicotyledonous weeds with GF-145, a new cereal herbicide product containing isoxaben and florasulam

Directory of Open Access Journals (Sweden)

Becker, Jörg

2014-02-01

Full Text Available GF-145 contains the active ingredients isoxaben (610 g ai/kg and florasulam (40 g ai/kg and is formulated as a Wettable Granule (WG. The active ingredients are found in commercial products such as Primus™2 (florasulam, Starane XL™ (fluroxypyr + florasulam, Ariane C™ (fluroxypyr + florasulam + clopyralid or Flexidor™ (isoxaben. While florasulam has been widely used in cereal crops in recent years, isoxaben offers a new mode of action (MOA for use in German cereal herbicides even when considering that Flexidor™ has had regulatory approval in 1988 to 1991. The MOA of isoxaben is inhibition of cellulose synthesis (HRAC class L, while florasulam inhibits Acetolactate Synthase (ALS and is a representative of the HRAC class B. It is known that florasulam works through uptake by green leaves. Isoxaben is a herbicide with soil activity and with a very low activity when foliar applied, except on some species in the cruciferae family. GF-145 is intended to be applied in the autumn in cereals (wheat, barley, rye, triticale for the control of ALS resistant volunteer oil seed rape and annual dicotyledonous weeds including Matricaria spp., Stellaria media, Papaver rhoeas, Capsella bursa-pastoris, Myosotis arvensis, Lamium spp., Galium aparine, Veronica spp. and others when applied at early post-emergence from BBCH 10 to 13 of the crop. The use rate in winter cereals is 95 g product/ha (58 g ai/ha isoxaben plus 3.75 g ai/ha florasulam. Field trials conducted in previous years confirmed excellent selectivity in all cereal crops and efficacy trials initiated in autumn 2012 show that GF-145 provides excellent and superior control to ALS resistant oil seed rape that was better than straight florasulam and other ALS active ingredients. GF-145 adds a new MOA to the cereal herbicide portfolio and controls volunteer oil seed rape, cruciferous weeds and broad-leaved weeds and is more robust than florasulam based products that do not contain isoxaben.

Thermal edible oil evaluation by UV-Vis spectroscopy and chemometrics.

Science.gov (United States)

Gonçalves, Rhayanna P; Março, Paulo H; Valderrama, Patrícia

2014-11-15

Edible oils such as colza, corn, sunflower, soybean and olive were analysed by UV-Vis spectroscopy and Multivariate Curve Resolution with Alternating Least Squares (MCR-ALS). When vegetable oils were heated at high temperatures (frying), oxidation products were formed which were harmful to human health in addition to degrading the antioxidants present, and this study aimed to evaluate tocopherol (one antioxidant present in oils) and the behaviour of oxidation products in edible oils. The MCR-ALS results showed that the degradation started at 110°C and 85°C, respectively, for sunflower and colza oils, while tocopherol concentration decreased and oxidation products increased starting at 70°C in olive oil. In soybean and corn oils, tocopherol concentration started to decrease and oxidation products increased at 50°C. The results suggested that sunflower, colza and olive oils offered more resistance to increasing temperatures, while soybean and corn oils were less resistant. Copyright © 2014 Elsevier Ltd. All rights reserved.

Kinetic Models Study of Hydrogenation of Aromatic Hydrocarbons in Vacuum Gas Oil and Basrah Crude Oil Reaction

Directory of Open Access Journals (Sweden)

Muzher M. Ibraheem

2013-05-01

Full Text Available             The aim of this research is to study the kinetic reaction models for catalytic hydrogenation of aromatic content for Basrah crude oil (BCO and vacuum gas oil (VGO derived from Kirkuk crude oil which has the boiling point rang of (611-833K.            This work is performed using a hydrodesulphurization (HDS pilot plant unit located in AL-Basil Company. A commercial (HDS catalyst cobalt-molybdenum (Co-Mo supported in alumina (γ-Al2O3 is used in this work. The feed is supplied by North Refinery Company in Baiji. The reaction temperatures range is (600-675 K over liquid hourly space velocity (LHSV range of (0.7-2hr-1 and hydrogen pressure is 3 MPa with H2/oil ratio of 300 of Basrah Crude oil (BCO, while the corresponding conditions for vacuum gas oil (VGO are (583-643 K, (1.5-3.75 hr-1, 3.5 MPa and 250  respectively .            The results showed that the reaction kinetics is of second order for both types of feed. Activation energies are found to be 30.396, 38.479 kJ/mole for Basrah Crude Oil (BCO and Vacuum Gas Oil (VGO respectively.

Organic pollutant removal from edible oil process wastewater using electrocoagulation

Science.gov (United States)

Sharma, S.; Can, O. T.; Hammed, M.; Nawarathna, D.; Simsek, H.

2018-03-01

Wastewaters generated from vegetable oil industries contain a high concentration of organic pollutants that are detrimental to the aquatic ecosystem. Electrochemical processes are gaining importance in the treatment of inorganic and resistant organic pollutants in wastewaters. In this study, electrocoagulation (EC) was applied to remove organic pollutants and oil and grease from canola oil wastewater using aluminum (Al) and iron (Fe) electrodes. The application of EC in the wastewater achieved more than 80% removal of organic carbon and nearly 100% removal of suspended solids (SS). The effectiveness of EC is influenced mainly by current density, pH, electrolyte (NaCl), electrode contact time and electrode type. It was observed that Al electrode combination yielded better removal at a lesser time compared to that of Fe electrodes. However, varying current densities had its significance in terms of coagulation time only. Increase in current density achieved decrease in coagulation time. Both Al and Fe could remove between 52-59% of oil and grease from canola oil wastewater

Oil as a design parameter in screw-type engines - use of non-newtonian oils. Pt. 1; Oel als Konstruktionselement in Schraubenmaschinen - Einsatz nicht newtonscher Oele. T. 1

Energy Technology Data Exchange (ETDEWEB)

Kauder, K.; Deipenwisch, R. [Dortmund Univ. (Germany). FG Fluidenergiemaschinen

1998-12-31

The model of the calculation of the friction losses caused by oil described in this report delivers a starting point for the integration of the design parameter `oil` for oil injected screw-type engines. The use of non newtonian oils with a shear thinning behaviour lead to a decrease of energy consumption over a broad speed range of screw-type compressors. The decrease is mainly caused by the shear indicated lower viscosity in the clearances of the compressor. A difficulty through the use of this oils is the estimation of the conditions in the clearances. The rate of shear in the single clearance is influenced by the relative speed of the boundaries and by the height of the clearance during operation. Up to now only cold heights were used in the model. To improve the quality of the model the clearances of a running screw compressor were measured. The losses which were determined at the screw compressor test plant are the summation of all losses including the losses caused by the power transmission and in the bearings. Experiments at a model rotor test stand make the determination of the friction losses and the losses by the acceleration of the oil in the clearances possible. A better calculation model shall deliver the conditions to describe the influence of the oil on the energy efficiency and to define the optimal oil for every screw compressor. (orig.) [Deutsch] Das beschriebene Modell zur Berechnung der hydraulischen Verluste in der nasslaufenden Schraubenmaschine liefert Ansaetze, um das Oel schon bei der Auslegung der Schraubenkompressoren als Konstruktionselement mit einzubeziehen. Sinnvoll ist die Nutzung eines nicht-newtonschen Oeles immer dann, wenn eine deutliche scherindizierte Viskositaetserniedrigung in dem Schergeschwindigkeitsbereich, der in den Spalten des Schraubenkompressors vorliegt, erreicht werden kann. Beim Einsatz dieser Oele besteht die Schwierigkeit darin, den Schergeschwindigkeitsbereich vorherzubestimmen, der waehrend des Betriebs in dem

Obuotor et al (16)

African Journals Online (AJOL)

DELL

fractions and essential oils from the leaves of Eugenia uniflora were investigated on some multidrug resistant pathogens. ... et al., 1987), a reduction in blood pressure measured ..... from E. uniflora suggests high efficacy against this bacterium.

The essential oil composition and antimicrobial activity of leaves of ...

African Journals Online (AJOL)

bmayekiso

2012-05-10

May 10, 2012 ... hydro-distillation during summer and winter months. Both essential oils were analyzed by gas .... Hydro-distillation of leaves and branches of S. hippifolium yielded an essential oil which was light blue in .... to the out-membrane structure of Gram-negative bacteria. (Delamare et al., 2005; Page et al., 1997).

Influence of the milling process on the structure and morphology of ZnAl_2O_4 and catalytic performance in the methyl transesterification reaction of soybean oil

International Nuclear Information System (INIS)

Feitosa, A.C.; Dantas, B.B.; Santana, A.; Costa, A.C.M.F.; Costa, D.B.

2012-01-01

This work aimed to evaluate the effect of milling time over the structure and morphology of ZnAl_2O_4, synthesized by combustion reaction, and study the effect of milled samples over the methyl transesterification reaction of soy bean oil. ZnAl_2O_4 was synthesizing, by means combustion reaction, using a electrical resistance plate. The powder was milled over 15, 30, 45 and 60 minutes and the samples were characterized by X-ray diffraction, scanning electron micrograph, particle size distribution and N_2 adsorption isotherms. Milling process promoted changes over the agglomerate size and textural characteristics of the samples. Catalytic tests were conducted at 160 deg C, with 1% of catalyst, with molar ratio oil:methanol of 1:6 and reaction time of 1 hour. According the results, the sample milled over 30 minutes showed the highest conversion. (author)

Vegetable oils in the agriculture. Experience reports; Pflanzenoel als Kraftstoff in der Landwirtschaft. Erfahrungsberichte

Energy Technology Data Exchange (ETDEWEB)

Kemnitz, Dietmar [Fachagentur Nachwachsende Rohstoffe e.V., Guelzow (Germany); Paul, Nicole [Fachagentur Nachwachsende Rohstoffe e.V., Guelzow (Germany); WPR COMMUNICATION GmbH und Co. KG, Koenigswinter/Bonn (Germany); Wichmann, Volker; Schuemann, Ulrike [Rostock Univ. (Germany); Maurer, Karl [Hohenheim Univ. (Germany); Remmele, Edgar [Technologie- und Foerderzentrum Straubing (Germany)

2006-08-15

In the agriculture, bio fuels increasingly meet with great interest. The use of bio diesel and vegetable oil as alternative fuels in diesel engines requires clear technical adjustments. The brochure under consideration reports on realizations of farmers who switched their tractors to an operation with vegetable oils. The brochure consists of the following contributions: (a) Employment of vegetable oil as fuel in the agriculture (empiric reports of farmers); (b) Re-equipment on operation with vegetable oil (empiric reports of reequipping persons); (c) Scientifically accompanying research of re-equipment (results of a 100-tractor-demonstration project); (d) Mixtures of plant oil and diesel fuel (results from engine test stand investigations); (e) Production of vegetable oil (experiences from an oil mill operator); (f) scientifically accompanying research for the production of vegetable oils (references to the production of rapeseed oil fuel according to the standard DIN 51605); (g) Hints and notes for the practice; (h) Fuel filling stations for self-consumers and storage of vegetable oil; (i) FNR funding programs bio fuels in the agriculture; (j) Adresses and contact persons.

Conformational change of oil contaminants adhered onto crystalline alpha-alumina surface in aqueous solution

International Nuclear Information System (INIS)

Xie, Wenkun; Sun, Yazhou; Liu, Haitao; Fu, Hongya; Liang, Yingchun

2016-01-01

Graphical abstract: - Highlights: • Dynamic conformational change process of oil contaminations adhered onto Al-terminated α-Al_2O_3 surface in aqueous solution is given. • Effect of water penetration on the conformational change and even detachment of oil contaminants is considered. • Change of driving forces leading to the conformational change of oil contaminants is described. - Abstract: Microscopic conformational change of oil contaminants adhered onto perfect α-Al_2O_3 (0001) surface in the aqueous solution was simulated by means of detailed fully atomistic molecular dynamics simulations. The main driving forces of the conformation change process of the oil contaminants were explored. The simulation results indicate that with submerging of the contaminated α-Al_2O_3 (0001) surface into the aqueous solution, the oil contaminants undertake an evident conformational change process. The dynamic process can be divided into several stages, including early penetration of water molecules, formation and widening of water channel, and generation of molecularly adsorbed hydration layers. Moreover, the oil contaminants on the α-Al_2O_3 surface are not fully removed from solid surface after a 10 ns relaxation, while a relatively stable oil/water/solid three-phase interface is gradually formed. Further, the residual oil contaminants are finally divided into several new ordered molecular adsorption layers. In addition, by systemically analyzing the driving forces for the conformational change of the oil contaminants, the penetration of water molecules is found to be the most important driving force. With penetrating of the water molecules, the dominating interactions controlling the conformational change of the oil contaminants have been changing over the whole simulation.

Effect of lithological composition of oil reservoirs on oil production by a hot agent

Energy Technology Data Exchange (ETDEWEB)

Abbasov, A A; Kasimov, Sh A

1965-01-01

Several small-scale experiments were performed to determine the effect of steam on oil recovery and on permeability of water-sensitive clay-containing cores. Steam has 2 contradictory actions on oil recovery - (1) steam increases temperature and decreases viscosity of the oil, which aids oil recovery; and (2) steam hydrates and swells clays, which reduces permeability and hinders oil recovery. The oil-recovery experiments were carried out with consolidated cores containing 0, 10, and 22% clay, saturated with water and 28 cp crude oil; superheated steam at 125-300$C was used. The following conclusions were made from the experimental results: (1) oil recovery decreased as clay content of cores increased; however, at all temperatures steam recovered more oil than cold water did. (2) As steam temperature increases, oil recovery reaches a maximum, then decreases. The temperature at which oil recovery begins to decrease depends on core clay content; the higher the clay content, the lower this temperature. (3) Irrespective of whether a reservoir contains clay or not, oil recovery is considerably greater with steam than with water.

Transesterification of coconut oil for FAME production using ultrasound

Science.gov (United States)

Supriadi, Eko; Marlinda, Lenny; Prajitno, Danawati Hari; Mahfud, Mahfud

2017-05-01

To overcome energy crisis, the vegetable oils-derived biofuel can be chosen as an alternative to petroleum-based diesel. The transesterification of coconut oil in methanol with K/γ-Al2O3 catalyst using ultrasound-assisted to produce fatty acid methyl ester (FAME) as one of type biofuel was studied. The reaction occurred in batch reactor at a 9 : 1 molar ratio of methanol to coconut oil. The following reaction conditions were used in the catalytic test : concentration of catalyst to oil of 0.5, 1.0, 1.5, 2.0, and 2.5%, the reaction time of 10, 20, 30, 60, 90, 120, and 150 s, and the frequency ultrasonication of 20 and 40 KHz. At first, the preparation of K/γ-Al2O3 catalyst was done and followed by transesterification process. After reaction, the phase separation and purification from impurities were done. Finally, FAME was analized based on this parameters, i.e., yield, density, viscosity, and flash point. FAME yield of 93.76% was obtained at the frequency ultrasonication of 40 kHz with K/γ-Al2O3 catalyst concentration to oil of 2.5 wt.% for 150 s. It's the best conditions for FAME production by transesterification of coconut oil using ultrasound-assisted.

Caspian Oil and Gas: Production and Prospects

National Research Council Canada - National Science Library

Gelb, Bernard A

2005-01-01

.... The Caspian Sea region historically has been an oil and natural gas producer, but many believe that the region contains large reserves of oil and gas capable of much greater production than at present...

Determination of the agricultural and process-related boundary conditions for the use of rapeseed oil and its refinery products as motor fuel. Final report; Ermittlung der landwirtschaftlichen, prozesstechnischen und verfahrenstechnischen Rahmenbedingungen fuer die Verwendung von Rapsoel und seiner Umwandlungsprodukte als Kraftstoff. Schlussbericht

Energy Technology Data Exchange (ETDEWEB)

Schliephake, D; Hacker, C M

1994-11-01

The use of rapeseed oil as a motor fuel is viewed from various angles: Production aspects; environmental aspects; marketing aspects in agriculture; business management aspects in the Federal Republic of Germany; production and refining of rapeseed oil; use of rapeseed oil methyl ester as diesel fuel and in mineral oil processing plants; engine performance. (orig./SR) [Deutsch] In dem vorliegenden Bericht wird der Einsatz von Rapsoel als Kraftstoff aus verschiedenen Blickwinkeln betrachtet: Produktionsaspekte, Umweltaspekte, marktwirtschaftliche Aspekte in der Landwirtschaft; betriebswirtschaftliche Aspekte in der Bundesrepublik Deutschland; Herstellung und Raffination von Rapsoel; Einsatz von Rapsoelmethylester als Dieselkraftstoff und in Anlagen der Mineraloelverarbeitung; Motortechnische Untersuchungsergebnisse. (orig./SR)

Hydrotreating of heavy gas oil derived from Athabasca bitumen using NiMo/Al2O3 catalyst containing boron and phosphorus : effects of process conditions on the product selectivity

Energy Technology Data Exchange (ETDEWEB)

Ferdous, D.; Dalai, A.K. [Saskatchewan Univ., Saskatoon, SK (Canada). Dept. of Chemistry and Chemical Engineering; Adjaye, J. [Syncrude Canada Ltd., Edmonton, AB (Canada). Edmonton Research Centre

2004-07-01

In response to concerns regarding the depletion of conventional oil reserves, there has been much interest in modifying the hydrotreating process for upgrading tar sands and shale oils for producing transportation fuels. Oil sand bitumens and their derived products have a high level of nitrogen which deactivates the catalysts used in fluid catalytic cracking and hydrocracking. A better catalyst is needed to efficiently remove nitrogen from oil sand-derived gas oils. In this study, a trickle-bed reactor containing NiMo/Al{sub 2}O{sub 3} catalysts with boron and phosphorous was used to remove the sulfur and nitrogen from heavy gas oils derived from Athabasca bitumen. The operating conditions of the reactor in terms of temperature and pressure were described. Sulfur and nitrogen conversion was found to increase substantially with the boron catalysts. Gasoline selectivity also increased with an increase in temperature. However, a change in operating conditions did not significantly affect the net content of the gas oil fraction. This study also compared the results of using either the boron or phosphorous catalyst.

Corrosion behavior of Fe-Si metallic coatings added with NiCrAlY in an environment of fuel oil ashes at 700 C

Energy Technology Data Exchange (ETDEWEB)

Salinas-Bravo, V.M.; Porcayo-Calderon, J.; Romero-Castanon, T. [Instituto de Investigaciones Electricas, Gerencia de Procesos Termicos., Av. Reforma 113, C.P. 62490 Col. Palmira. Temixco. Morelos (Mexico); Dominguez-Patino, G.; Gonzalez-Rodriguez, J.G. [U.A.E.M. Centro de Investigaciones en Ingenieria y Ciencias Aplicadas., Av. Universidad 1001, C.P. 62210, Col. Chamilpa. Cuernavaca, Morelos (Mexico)

2005-07-01

Electrochemical potentiodynamic polarization curves and immersion tests for 300 h at 700 C in a furnace have been used to evaluate the corrosion resistance of Fe-Si metallic coatings added with up to 50 wt.% of NiCrAIY. The corrosive environment was fuel oil ashes from a steam generator. The composition of fuel oil ashes includes high content of vanadium, sodium and sulfur. The results obtained show that only the addition of 20 wt.% NiCrAlY to the Fe-Si coating improves its corrosion resistance. The behavior of all tested coatings is explained by the results obtained from the analysis of every coating using electron microscopy and energy dispersive X-ray analysis. (Abstract Copyright [2005], Wiley Periodicals, Inc.)

Modification of the process for separating and recovering oil from oil-sands, etc

Energy Technology Data Exchange (ETDEWEB)

Preller, H

1922-08-30

A method of carrying out the process according to Patent 400,122 especially for washing oil or bitumen-bearing mineral materials contaminated with more or less clay, marl, and so forth is characterized in that the oil-bearing raw material is first washed in an opposing stream of warm water for separating the larger part of the oil and settling the larger part of the rock. At the same time the fine clay suspended during the washing operation to a large extent and the remaining rock particles, which are unbound from the oil, by means of a regulatable water stream for further washing are carried into a receptacle of greater cross section, where by the very slow rise of the liquid the finer oil particles find an opportunity to ascend.

Spray pyrolysis synthesis of γ-Al_2O_3 supported metal and metal phosphide catalysts and their activity in the hydrodeoxygenation of a bio-oil model compound

International Nuclear Information System (INIS)

Ly, Hoang Vu; Im, Kyungmin; Go, Youngchae; Galiwango, Emmanuel; Kim, Seung-Soo; Kim, Jinsoo; Choi, Jae Hyung; Woo, Hee Chul

2016-01-01

Highlights: • Spherical γ-Al_2O_3 supported metal and metal phosphide catalysts were synthesized by spray pyrolysis method. • Hydrodeoxygenation (HDO) of 2-furyl methyl ketone (FMK) was conducted using metal/metal phosphide catalysts. • FMK was converted into 2-allyl furan and methyl cyclohexane. • The highest FMK conversion of 83% was achieved over 10 wt% Ni/γ-Al_2O_3 catalysts at reaction temperature of 400 °C. - Abstract: In this study, spherical γ-Al_2O_3 supported metal and metal phosphide (Ni, Co, Ni_2P and CoP) catalysts were successfully prepared by combining sol-gel and spray pyrolysis methods. First boehmite sol was prepared based on the Yoldas process and then the corresponding metal salts were added to the sol at the desired concentration, followed by spray pyrolysis of the mixed solution. As the well-mixed solution was transformed to spherical γ-Al_2O_3 supported metal and metal phosphide catalysts during spray pyrolysis process, the metal species were uniformly distributed in the mesoporous γ-Al_2O_3 supports. The product catalysts were investigated under different conditions for hydrodeoxygenation of bio-oil model compound, 2-furyl methyl ketone (FMK), which is the main component of the bio-oil product from pyrolysis of Saccharina japonica. Among the investigated catalysts, the 10 wt% Ni/γ-Al_2O_3 catalyst after calcination at 800 °C showed the highest FMK conversion of 83.02% at the reaction temperature of 400 °C. The gas and liquid products were analyzed by gas chromatography (GC) with TCD/FID detectors and GC–MS, respectively, to determine the product compositions.

The future of oil and bioethanol in Brazil

International Nuclear Information System (INIS)

Moreira, Jose R.; Pacca, Sergio A.; Parente, Virginia

2014-01-01

This work compares the return on investments (ROI) of oil versus biofuels in Brazil. Although several renewable energy sources might displace oil, the country's forte is sugarcane biofuels. In our analysis we carry out simplified benefit–cost analyses of producing oil fields, pre-salt oil fields (without and with enhanced oil recovery), a business as the usual ethanol scenario, and a high ethanol scenario. Excluding the ROI from existing oil fields, which is the highest, when the discount rate is 4% or more, the ROI of the high ethanol scenario is greater than that of the ROI of pre-salt oil. Considering a US$40/t CO 2 tax, the high ethanol scenario's ROI is greater than the pre-salt oil's ROI if a discount rate of 2% or more is adopted. Moreover, the high ethanol scenario throughput up to 2070 compares to 97% of the pre-salt oil reserve without EOR, and demands 78% of its investment. Pre-salt oil production declines beyond 2042 when the country might become a net oil importer. In contrast, ethanol production reaches 2.1 million boe per day, and another 0.9 million boe of fossil demand is displaced through bioelectricity, yielding a total of 3 million boe (62% of the country's oil demand). - Highlights: • Cost-benefit analyses of pre-salt and biofuels in Brazil. • Hubbert model applied to pre-salt oil reserves. • Sustainable energy scenarios. • Carbon mitigation accounting based on biofuel scenarios. • Enhanced oil recovery effect on pre-salt oil reserves

Method and apparatus for recovering oil from an oil spill on the surface of a body of water

International Nuclear Information System (INIS)

Schweizer, R.W.; Patel, K.P.; Lau, P.Y.

1991-01-01

This patent describes a method of recovering a hydrophobic hydrocarbon oil from the surface of a body of water, the body of water having a water temperature, the oil having a specific gravity which is less than the specific gravity of the water in the body of water and a viscosity which is greater than approximately 80 centipoise at the water temperature. It comprises continuously withdrawing a feed oil-water mixture from the surface of the body of water; continuously adjusting the viscosity of the oil in the feed oil-water mixture to a level below approximately 80 centipoise to form an adjusted oil-water mixture; and continuously passing the adjusted oil-water mixture through an oil-water coalescer to separate the oil in the adjusted oil-water mixture from the water in the adjusted oil-water mixture

Oil demand asymmetry in the OECD

International Nuclear Information System (INIS)

Shealy, M.T.

1990-01-01

Oil demand asymmetry exists, is significant, and can be captured with a simple demand equation using a Pmax term. The unstable parameters of the original symmetric equations suggest misspecification. Addition of a Pmax term to represent asymmetry yields stable parameters from 1982 through 1989 and so suggests proper specification. Asymmetry is significant because the short-run (and long-run) price elasticity is less than half as large when oil price falls as when price rises beyond the past peak. The lower elasticity applies both to price decreases and also to price increases for which price remains below the past peak. As long as the real oil price remains well below the 1981 peak, asymmetry implies that OECD oil demand should be less sensitive to oil price variations than in 1981. More specifically, the results shown suggest that today's oil demand elasticity should be less than half as large as the elasticity for a price increase in 1981. Forecasts from the asymmetric equations are significantly higher than the DOE base-case forecast. DOE's lower forecast is due to greater price asymmetry through 1995 and to higher long-run price elasticity beyond 1995. One reason for the higher long-run price elasticity might be greater assumed improvements in energy-efficiency than implied by the historical data

Performance Assessment and Scooter Verification of Nano-Alumina Engine Oil

Directory of Open Access Journals (Sweden)

Yu-Feng Lue

2016-09-01

Full Text Available The performance assessment and vehicle verification of nano-alumina (Al2O3 engine oil (NAEO were conducted in this study. The NAEO was produced by mixing Al2O3 nanoparticles with engine oil using a two-step synthesis method. The weight fractions of the Al2O3 nanoparticles in the four test samples were 0 (base oil, 0.5, 1.5, and 2.5 wt. %. The measurement of basic properties included: (1 density; (2 viscosity at various sample temperatures (20–80 °C. A rotary tribology testing machine with a pin-on-disk apparatus was used for the wear test. The measurement of the before-and-after difference of specimen (disk weight (wear test indicates that the NAEO with 1.5 wt. % Al2O3 nanoparticles (1.5 wt. % NAEO was the chosen candidate for further study. For the scooter verification on an auto-pilot dynamometer, there were three tests, including: (1 the European Driving Cycle (ECE40 driving cycle; (2 constant speed (50 km/h; and (3 constant throttle positions (20%, 40%, 60%, and 90%. For the ECE40 driving cycle and the constant speed tests, the fuel consumption was decreased on average by 2.75%, while it was decreased by 3.57% for the constant throttle case. The experimental results prove that the engine oil with added Al2O3 nanoparticles significantly decreased the fuel consumption. In the future, experiments with property tests of other nano-engine oils and a performance assessment of the nano-engine-fuel will be conducted.

Microbial consortia in Oman oil fields: a possible use in enhanced oil recovery.

Science.gov (United States)

Al-Bahry, Saif N; Elshafie, Abdulkader E; Al-Wahaibi, Yahya M; Al-Bemani, Ali S; Joshi, Sanket J; Al-Maaini, Ratiba A; Al-Alawi, Wafa J; Sugai, Yuichi; Al-Mandhari, Mussalam

2013-01-01

Microbial enhanced oil recovery (MEOR) is one of the most economical and efficient methods for extending the life of production wells in a declining reservoir. Microbial consortia from Wafra oil wells and Suwaihat production water, Al-Wusta region, Oman were screened. Microbial consortia in brine samples were identified using denaturing gradient gel electrophoresis and 16S rRNA gene sequences. The detected microbial consortia of Wafra oil wells were completely different from microbial consortia of Suwaihat formation water. A total of 33 genera and 58 species were identified in Wafra oil wells and Suwaihat production water. All of the identified microbial genera were first reported in Oman, with Caminicella sporogenes for the first time reported from oil fields. Most of the identified microorganisms were found to be anaerobic, thermophilic, and halophilic, and produced biogases, biosolvants, and biosurfactants as by-products, which may be good candidates for MEOR.

Design and development of a high efficiency tank for crude oil dehydration (i)

International Nuclear Information System (INIS)

Forero, Jorge Enrique; Ortiz Olga Patricia; Narino, Fredy Abelardo

2008-01-01

This paper introduces a new tank design for dehydrating and desalting large volumes of crude oils previously degasified, crude oil dehydration efficiency is reduced by gas presence in the emulsion interphase. The design presented in this paper is versatile (it is adaptable to any classical dehydration process), highly efficient in terms of separation (values usually greater than 90% and/or treated crude oil BSW less than 0,5% are ensured), low installation and operation costs, less consumption of additives. These are some of the advantages found in pilot tests plants and proven in industrial systems at the ECOPETROL S.A. production fields with treatment capacities from 14 to 50 KBD. Although this process also can be applied to other ranks of flow, maintaining the design critical conditions of each case in particular. This system does not exhibit the typical limitations shown by treatment traditional systems (FWKO, Gun Barrel, thermal and electrostatic separators, etc.) (Al-Ghamdi, 2007) since it can be easily adapted to system treatments for light, intermediate, and heavy crude oils and to treatments with BSW content ranging from a very low levels of ≤ 1% to very high levels ≥ 95%, values that are not unusual in production fields nowadays, especially where accelerated production methods are used

Oil bodies and their associated proteins, oleosin and caleosin

DEFF Research Database (Denmark)

Frandsen, Gitte I.; Mundy, John; Tzen, Jason T. C.

2001-01-01

Oil bodies are lipid storage organelles which have been analyzed biochemically due to the economic importance of oil seeds. Although oil bodies are structurally simple, the mechanisms involved in their formation and degradation remain controversial. At present, only two proteins associated with oil....... (1999) Plant Cell Physiol 40: 1079-1086; Naested et al. (2000) Plant Mol Biol 44: 463-476]. Caleosin and caleosin-like proteins are not unique to oil bodies and are associated with an endoplasmatic reticulum subdomain in some cell types. Here we review the synthesis and degradation of oil bodies...

Experimental study on kinetics oil oil-suspended particulate matter aggregation

International Nuclear Information System (INIS)

Sun, J.; Environment Canada, Ottawa, ON; Khelifa, A.; Wang, Z.; Brown, C.; Fieldhouse, B.; Yang, C.; Zheng, X.; Wong, S.; So, L.C.

2009-01-01

Past studies of oil spills have shown that oil suspended particulate matter aggregates (OSAs) play a role in enhancing the natural cleansing of oiled shorelines. OSAs result from aggregation between suspended oil droplets and suspended particulate matter (SPM) in aquatic environments. During this process, oil dispersion into the water column is significantly increased since the surface of the oil droplet is surrounded by sediment particles. In addition, the accelerated biodegradation of the oil can be attributed to the greater oil-water contact area. This study focused on the kinetic aspects of OSA formation, with particular reference to the time scale of this process and its significance to oil dispersion following oil spills in water. A laboratory study was conducted to measure the time scale of OSA formation and its variations with mixing conditions. A reciprocating shaker and various oil/sediment mixtures were used to prepare the OSAs. Standard reference material 1941b was used as the natural sediment mixed with Arabian medium crude and artificial seawater under various mixing energies. The sediment-to-oil ratio remained constant for all experiments. Gas chromatography-flame ionization detection (GC-FID) analysis was used to measure the total petroleum hydrocarbons (TPH) trapped in negatively buoyant OSAs. Results showed that the TPH in OSAs increased exponentially with shaking time and reached an equilibrium value within 3 hours. The equilibrium decreased from 3 hours to 1.3 hours when the shaking rate increased from 2.0 to 2.3 Hz. It was concluded that high mixing energy enhances OSA formation and shortens the time for OSA formation. 42 refs., 6 tabs., 5 figs

Experimental study on kinetics oil oil-suspended particulate matter aggregation

Energy Technology Data Exchange (ETDEWEB)

Sun, J. [Ocean Univ. of China, Qingdoa (China). Environmental Science and Engineering Inst.; Environment Canada, Ottawa, ON (Canada). Emergencies Science and Technology Section, Emergencies, Operational Analytical Laboratories and Research Support Division; Khelifa, A.; Wang, Z.; Brown, C.; Fieldhouse, B.; Yang, C. [Environment Canada, Ottawa, ON (Canada). Emergencies Science and Technology Section, Emergencies, Operational Analytical Laboratories and Research Support Division; Zheng, X. [Ocean Univ. of China, Qingdoa (China). Environmental Science and Engineering Inst.; Wong, S. [Ottawa Univ., ON (Canada). Dept. of Chemistry; So, L.C. [Waterloo Univ., ON (Canada). Faculty of Engineering

2009-07-01

Past studies of oil spills have shown that oil suspended particulate matter aggregates (OSAs) play a role in enhancing the natural cleansing of oiled shorelines. OSAs result from aggregation between suspended oil droplets and suspended particulate matter (SPM) in aquatic environments. During this process, oil dispersion into the water column is significantly increased since the surface of the oil droplet is surrounded by sediment particles. In addition, the accelerated biodegradation of the oil can be attributed to the greater oil-water contact area. This study focused on the kinetic aspects of OSA formation, with particular reference to the time scale of this process and its significance to oil dispersion following oil spills in water. A laboratory study was conducted to measure the time scale of OSA formation and its variations with mixing conditions. A reciprocating shaker and various oil/sediment mixtures were used to prepare the OSAs. Standard reference material 1941b was used as the natural sediment mixed with Arabian medium crude and artificial seawater under various mixing energies. The sediment-to-oil ratio remained constant for all experiments. Gas chromatography-flame ionization detection (GC-FID) analysis was used to measure the total petroleum hydrocarbons (TPH) trapped in negatively buoyant OSAs. Results showed that the TPH in OSAs increased exponentially with shaking time and reached an equilibrium value within 3 hours. The equilibrium decreased from 3 hours to 1.3 hours when the shaking rate increased from 2.0 to 2.3 Hz. It was concluded that high mixing energy enhances OSA formation and shortens the time for OSA formation. 42 refs., 6 tabs., 5 figs.

Intrastate conflict in oil producing states: A threat to global oil supply?

International Nuclear Information System (INIS)

Toft, Peter

2011-01-01

In this paper I investigate how often and how much outbreaks of intrastate conflict in oil producing states translates into oil supply shortfalls. The Libyan conflict that broke out in February 2011 highlighted the fear that intrastate conflict in oil producing states may imply shortfalls and ensuing volatile global oil prices. I argue, however, that it is far from certain that shortfalls following conflict outbreak will occur, since both sides in a conflict face incentives simultaneously to protect and maintain oil installations and to strike and destroy these. Based on a quantitative analysis of 39 intrastate wars in oil producing countries (1965-2007) I conclude that outbreak of conflict does not translate into production decline with any certainty. In fact, likelihoods are less than 50% for reductions to occur. In many cases growing production actually followed conflict outbreak. I conclude by investigating four characteristics of intrastate conflict that may explain when oil production is at risk during conflict: (1) proximity of oil producing fields to key battle zones, (2) duration of conflict, (3) separatism and the location of oil in separatist territory, and (4) the relative size of oil production. While the first three factors did not prove important, oil producer size could be significant. But further research is needed to establish this with greater certainty. - Highlights: → Oil shortfall during intrastate conflict is not a given. → Statistical analysis of 39 intrastate conflicts in oil producing countries since 1965. → Examination of four characteristics of intrastate conflict in oil producing countries. → Marginal significance related to large producers and production shortfall.

Intrastate conflict in oil producing states: A threat to global oil supply?

Energy Technology Data Exchange (ETDEWEB)

Toft, Peter, E-mail: peter.toft@ec.europa.eu [Institute for Energy, Joint Research Centre of the European Commission, Westerduinweg 3, 1755 ZG Petten (Netherlands)

2011-11-15

In this paper I investigate how often and how much outbreaks of intrastate conflict in oil producing states translates into oil supply shortfalls. The Libyan conflict that broke out in February 2011 highlighted the fear that intrastate conflict in oil producing states may imply shortfalls and ensuing volatile global oil prices. I argue, however, that it is far from certain that shortfalls following conflict outbreak will occur, since both sides in a conflict face incentives simultaneously to protect and maintain oil installations and to strike and destroy these. Based on a quantitative analysis of 39 intrastate wars in oil producing countries (1965-2007) I conclude that outbreak of conflict does not translate into production decline with any certainty. In fact, likelihoods are less than 50% for reductions to occur. In many cases growing production actually followed conflict outbreak. I conclude by investigating four characteristics of intrastate conflict that may explain when oil production is at risk during conflict: (1) proximity of oil producing fields to key battle zones, (2) duration of conflict, (3) separatism and the location of oil in separatist territory, and (4) the relative size of oil production. While the first three factors did not prove important, oil producer size could be significant. But further research is needed to establish this with greater certainty. - Highlights: > Oil shortfall during intrastate conflict is not a given. > Statistical analysis of 39 intrastate conflicts in oil producing countries since 1965. > Examination of four characteristics of intrastate conflict in oil producing countries. > Marginal significance related to large producers and production shortfall.

Comparison of P-containing {gamma}-Al{sub 2}O{sub 3} supported Ni-Mo bimetallic carbide, nitride and sulfide catalysts for HDN and HDS of gas oils derived from Athabasca bitumen

Energy Technology Data Exchange (ETDEWEB)

Sundaramurthy, V.; Dalai, A.K. [Catalysis and Chemical Reaction Engineering Laboratories, Department of Chemical Engineering, University of Saskatchewan, Saskatoon, SK (Canada); Adjaye, J. [Syncrude Edmonton Research Centre, Edmonton, AB (Canada)

2006-09-01

Phosphorus containing {gamma}-Al{sub 2}O{sub 3} supported bimetallic Ni-Mo carbide, nitride and sulfide catalysts have been synthesized from an oxide precursor containing 12.73wt.% Mo, 2.54wt.% Ni and 2.38wt.% P and characterized by elemental analysis, pulsed CO chemisorption, surface area measurements, X-ray diffraction, temperature-programmed reduction and DRIFT spectroscopy of CO adsorption. DRIFT spectroscopy of adsorbed CO on activated catalysts showed that carbide and nitride catalysts have surface exposed sites of Mo{sup o+} (0Al{sub 2}O{sub 3} catalyst in a trickle bed reactor using light gas oil and heavy gas oil derived from Athabasca bitumen in the temperature range 340-370 and 375-400{sup o}C respectively at 8.8MPa. The gradual transformation of Ni-Mo carbide and nitride phases into Ni-Mo sulfide phases was observed during precoking period, and the formed Ni-Mo sulfide phases enhanced the HDN and HDS activities of carbide and nitride catalysts. The {gamma}-Al{sub 2}O{sub 3} supported Ni-Mo bimetallic sulfide catalyst was found to be more active for HDN and HDS of light gas oil and heavy gas oil than the corresponding carbide and nitride catalysts on the basis of unit weight. (author)

Tomato Sauce Enriched with Olive Oil Exerts Greater Effects on Cardiovascular Disease Risk Factors than Raw Tomato and Tomato Sauce: A Randomized Trial

Directory of Open Access Journals (Sweden)

Palmira Valderas-Martinez

2016-03-01

Full Text Available Epidemiological studies have observed a negative association between tomato intake and the incidence of cardiovascular disease. As tomato sauces are usually cooked with the addition of oil, some studies have pointed out that both processes may increase the bioavailability of the bioactive compounds. However, the effect of consumption of raw tomatoes and tomato sauces on inflammation biomarkers and adhesion molecules related to atherosclerosis remains unknown. The aim of this study was to test the postprandial effects of a single dose of raw tomatoes (RT, tomato sauce (TS and tomato sauce with refined olive oil (TSOO on cardiovascular disease risk factors. We performed an open, prospective, randomized, cross-over, controlled feeding trial in 40 healthy subjects who randomly received: 7.0 g of RT/kg of body weight (BW, 3.5 g of TS/kg BW, 3.5 g of TSOO/Kg BW and 0.25 g of sugar solved in water/kg BW on a single occasion on four different days. Biochemical parameters and cellular and circulating inflammatory biomarkers were assessed at baseline and 6 h after each intervention. The results indicate that, compared to control intervention, a single tomato intake in any form decreased plasma total cholesterol, triglycerides and several cellular and plasma inflammatory biomarkers, and increased plasma high density lipoproteins (HDL cholesterol and interleukine (IL 10 concentrations. However, the changes of plasma IL-6 and vascular cell adhesion molecule-1 (VCAM-1, and lymphocyte function-associated antigen-1 (LFA-1 from T-lymphocytes and CD36 from monocytes were significantly greater after TSOO than after RT and TS interventions. We concluded that tomato intake has beneficial effects on cardiovascular risk factors, especially cooked and enriched with oil.

When oil spills emulsify

International Nuclear Information System (INIS)

Bobra, M.; Fingas, M.; Tennyson, E.

1992-01-01

Cleanup operations of oil spills must take into account the numerous detrimental effects attributable to the emulsification of spilled oil into a stable water-in-oil mousse. The incorporation of water greatly increases the volume of the polluted material. The viscous nature of mousse impedes the efficient operation of most mechanical recovery equipment and results in a cohesive slick that resists dispersion, both natural and artificial. The rate at which spilled oil emulsifies determines the effective window of opportunity for specific countermeasures. Much has been learned from previous studies on petroleum emulsification, but is still remain a poorly understood phenomenon. Although most crude oils can be emulsified, not all spills result in the formation of stable mousse. The formation of mousse results from a complex series of processes. Whether an oil will form mousse or not, and if so, at what rate, depends on an array of different factors including the properties of the oil and the prevailing environmental conditions. We need a greater understanding of the emulsification process to better predict the emulsification behavior of oil spills and utilize the most appropriate countermeasures available. In this paper, the authors report on work to elucidate the role that physicochemical factors play in determining an oil's tendency to emulsify. The authors studied the emulsification behavior of oils of known composition to examine the importance of oil chemistry in the emulsification process

Floating Heavy Oil Recovery: Current State Analysis

Science.gov (United States)

2006-07-27

recovered oil to a chute cause some build-up of oil, but the retained amount was not considered substantial enough to warrant any design changes. The GT...unit was the Lamor Brush Conveyor (shown in Figure 7) which uses a yellow V- brush design to recover oils and uses a propeller to draw water through...deals with the transfer of product that has already been collected and contained (Moffatt et al., 2004). The Coast Guard Research and Development

Recycling used palm oil and used engine oil to produce white bio oil, bio petroleum diesel and heavy fuel

Science.gov (United States)

Al-abbas, Mustafa Hamid; Ibrahim, Wan Aini Wan; Sanagi, Mohd. Marsin

2012-09-01

Recycling waste materials produced in our daily life is considered as an additional resource of a wide range of materials and it conserves the environment. Used engine oil and used cooking oil are two oils disposed off in large quantities as a by-product of our daily life. This study aims at providing white bio oil, bio petroleum diesel and heavy fuel from the disposed oils. Toxic organic materials suspected to be present in the used engine oil were separated using vacuum column chromatography to reduce the time needed for the separation process and to avoid solvent usage. The compounds separated were detected by gas chromatography-mass spectrometry (GC-MS) and found to contain toxic aromatic carboxylic acids. Used cooking oils (thermally cracked from usage) were collected and separated by vacuum column chromatography. White bio oil produced was examined by GC-MS. The white bio oil consists of non-toxic hydrocarbons and is found to be a good alternative to white mineral oil which is significantly used in food industry, cosmetics and drugs with the risk of containing polycyclic aromatic compounds which are carcinogenic and toxic. Different portions of the used cooking oil and used engine were mixed to produce several blends for use as heavy oil fuels. White bio oil was used to produce bio petroleum diesel by blending it with petroleum diesel and kerosene. The bio petroleum diesel produced passed the PETRONAS flash point and viscosity specification test. The heat of combustion of the two blends of heavy fuel produced was measured and one of the blends was burned to demonstrate its burning ability. Higher heat of combustion was obtained from the blend containing greater proportion of used engine oil. This study has provided a successful recycled alternative for white bio oil, bio petroleum fuel and diesel which can be an energy source.

Reduction of Sulphur Content of Urals Crude Oil Prior to Processing ...

African Journals Online (AJOL)

during oxidation was carried out by extraction followed ... and from gas oil to 82 % (Gore et al., 2003). In 2004 ... treated light gas oil(LGO), it was reduced from 307 to ..... Oil Shale,. 23(2):164-176. Rappas, A.S. (2002). Process for removing low.

Inflation and the price of oil in Canada

Energy Technology Data Exchange (ETDEWEB)

Globerman, S A [York Univ., Toronto; Bruce, H A

1976-09-01

A current policy concern in North America is how rapidly (if at all) domestic oil prices should be allowed to rise to world levels. An argument frequently used by those advocating control of domestic prices is that further increases in oil prices would impose undue burdens in the form of greater inflation and unemployment. While long-run costs associated with allocative inefficiencies are recognized, critics of policies calling for decontrolling domestic oil prices argue that the short-run costs associated with greater inflation and higher unemployment outweigh the long-run inefficiencies associated with price controls. Estimates of the impacts of increased oil costs are not easy. Three studies by Ontario on the consumer price index are described, and the authors conclude that the figures from these studies are too high. Some results of U.S. studies are cited. (MCW)

The changing structure of the international oil industry: implications for OPEC

International Nuclear Information System (INIS)

Abdalla, K.L.; )

1995-01-01

This paper examines the changes in international oil market structure observed in the 1980s and early 1990s and assesses possible effects on oil market conditions in the future and implications for OPEC. It focuses on the trend toward a more vertical organization mainly resulting from substantial purchases of downstream assets by state owned oil companies in major oil producing countries. While the Gulf war prevented greater horizontal concentration of oil reserves, it merely interrupted the trend toward vertical concentration in the international oil industry. The vertical integration of only some of the OPEC members will cause a further divergence of goals within the organization resulting in a lower likelihood of OPEC regaining its former position as an effective cartel. If the trend toward greater vertical concentration increases, future oil prices will, in part, be affected by decisions made by vertically integrated firms. (author)

New evidence of anti-herding of oil-price forecasters

International Nuclear Information System (INIS)

Pierdzioch, Christian; Ruelke, Jan Christoph; Stadtmann, Georg

2010-01-01

We used the oil-price forecasts of the Survey of Professional Forecasters published by the European Central Bank to analyze whether oil-price forecasters herd or anti-herd. Oil-price forecasts are consistent with herding (anti-herding) of forecasters if forecasts are biased towards (away from) the consensus forecast. Based on a new empirical test developed by Bernhardt et al. (J. Financ. Econ. 80: 657-675, 2006), we found strong evidence of anti-herding among oil-price forecasters. (author)

Hydrodenitrogenation and hydrodesulphurization of heavy gas oil using NiMo/Al{sub 2}O{sub 3} catalyst containing phosphorous : experimental and kinetic studies

Energy Technology Data Exchange (ETDEWEB)

Ferdous, D.; Dalai, A.K. [Saskatchewan Univ., Saskatoon, SK (Canada). Dept. of Chemical Engineering; Adjaye, J. [Syncrude Canada Ltd., Edmonton, AB (Canada). Edmonton Research Centre

2005-10-01

Oil sand bitumens and their derived products contain high levels of nitrogen and sulfur compounds which cause the formation of SOx and NOx in the atmosphere. These compounds also deactivate the catalysts used in fluid catalytic cracking and hydrocracking. This study focused on finding a better catalyst to efficiently remove sulphur and nitrogen from oil sand-derived heavy gas oils. The NiMo/Al{sub 2}O{sub 3} catalyst with phosphorous (P) was used in a trickle-bed reactor under a range of temperature and pressure conditions to study the reactivity of vacuum, atmospheric and hydrocracked heavy gas oils produced from Athabasca bitumen. The concentration of phosphorous was maintained at 2.7 wt per cent, while the hydrogen flow rate and catalyst weight were maintained constant at 50 mL/min and 4 g respectively. An ANOVA analysis of experimental data was performed to optimize the process conditions for hydrodenitrogenation (HDN) and hydrodesulphurization (HDS) reactions. Kinetic studies for HDN and HDS reactions were studied within the temperature range of 340 to 400 degrees C using the power law model and the Langmuir-Hinshelhood model. It was shown that HDN and HDS of heavy gas oil follows first order kinetics. The activation energies for HDN and HDS reactions from the power law and Langmuir-Hinshelhood models were 94 and 96 kJ/mol and 113 and 137 kJ/mol, respectively. It was concluded that nitrogen and hydrogen sulfide adsorption have a significant influence on HDN and HDS reactions. 32 refs., 8 tabs., 7 figs.

Significance of abolishing British National Oil Corporation

Energy Technology Data Exchange (ETDEWEB)

Mabro, R

1985-04-01

The decision to abolish British National Oil Corporation has greater significance than any commentator, so far, has cared to admit. Mr. Mabro says the Government has done much more than get rid of an institution it had previously weakened and emasculated; in effect, it had abdicated its responsibilities for the pricing of North Sea oil. He further observes that these moves may be consistent with the tenets of a simplistic free-market ideology: they betray, however, a lack of understanding of the economics of oil, and of the UK economic interest in oil.

A study on wear resistance and microcrack of the Ti3Al/TiAl + TiC ceramic layer deposited by laser cladding on Ti-6Al-4V alloy

International Nuclear Information System (INIS)

Li Jianing; Chen Chuanzhong; Squartini, Tiziano; He Qingshan

2010-01-01

Laser cladding of the Al + TiC alloy powder on Ti-6Al-4V alloy can form the Ti 3 Al/TiAl + TiC ceramic layer. In this study, TiC particle-dispersed Ti 3 Al/TiAl matrix ceramic layer on the Ti-6Al-4V alloy by laser cladding has been researched by means of X-ray diffraction, scanning electron microscope, electron probe micro-analyzer, energy dispersive spectrometer. The main difference from the earlier reports is that Ti 3 Al/TiAl has been chosen as the matrix of the composite coating. The wear resistance of the Al + 30 wt.% TiC and the Al + 40 wt.% TiC cladding layer was approximately 2 times greater than that of the Ti-6Al-4V substrate due to the reinforcement of the Ti 3 Al/TiAl + TiC hard phases. However, when the TiC mass percent was above 40 wt.%, the thermal stress value was greater than the materials yield strength limit in the ceramic layer, the microcrack was present and its wear resistance decreased.

Hydrotreatment of bio-oil over Ni-based catalyst.

Science.gov (United States)

Zhang, Xinghua; Wang, Tiejun; Ma, Longlong; Zhang, Qi; Jiang, Ting

2013-01-01

Inexpensive non-sulfided Ni-based catalysts were evaluated for hydrotreatments using phenol as model compound. HZSM-5, a zeolite with different ratio of Si/Al and γ-Al(2)O(3) were impregnated with Ni(NO(3))(2) · 6H(2)O and calcined at 450 °C. Conversion rates and product distribution for treatment of phenol at 160-240 °C in the presence of catalysts with nickel loads of 6, 10, 14 and 17 wt.% were determined. Phenol conversion was highest (91.8%) at 240 °C in the presence of HZSM-5(Si/Al = 38) loaded with 10% Ni. When hydrotreatment was carried out with bio-oil obtained from pyrolysis of pine sawdust under the optimal conditions determined for phenol, the pH of bio-oil increased from 2.27 to 4.07, and the hydrogen content increased from 6.28 to 7.01 wt.%. The decrease in acidity is desirable for the use of upgraded bio-oil. Copyright © 2012. Published by Elsevier Ltd.

Jojoba oil and derivates

Energy Technology Data Exchange (ETDEWEB)

Wisniak, T

1977-01-01

Jojoba oil differs from all known seed oils by its almost complete absence of glycerides, making it more a liquid wax than a fat. It has become important as a possible substitute for sperm-whale oil to produce lubricants, lubricant additives and other products. The plant occurs naturally in southern Arizona and N.W. Mexico and its oil has long been used by Indians for medicinal, culinary, ritual and other purposes. It tolerates extreme daily fluctuations of temperature and grows well under the difficult soil and moisture conditions of the region. In the first part of this review the plant and its uses are described, including its floral, fruit and seed anatomy and the use of liquid wax during germination. Stored coryledon wax is used up by the embryo as a linear function of time during the first 30 days of germination and growth. Before germination, seeds weight about 0.59 mg and contain about 54% wax. The second and greater part of the review deals with jojoba oil (its extraction, properties, molecular description, toxicity and composition), jojoba meal, which remains after the oil has been extracted, and the chemical modification of the oil.

Nannochloropsis algae pyrolysis with ceria-based catalysts for production of high-quality bio-oils.

Science.gov (United States)

Aysu, Tevfik; Sanna, Aimaro

2015-10-01

Pyrolysis of Nannochloropsis was carried out in a fixed-bed reactor with newly prepared ceria based catalysts. The effects of pyrolysis parameters such as temperature and catalysts on product yields were investigated. The amount of bio-char, bio-oil and gas products, as well as the compositions of the resulting bio-oils was determined. The results showed that both temperature and catalyst had significant effects on conversion of Nannochloropsis into solid, liquid and gas products. The highest bio-oil yield (23.28 wt%) and deoxygenation effect was obtained in the presence of Ni-Ce/Al2O3 as catalyst at 500°C. Ni-Ce/Al2O3 was able to retain 59% of the alga starting energy in the bio-oil, compared to only 41% in absence of catalyst. Lower content of acids and oxygen in the bio-oil, higher aliphatics (62%), combined with HHV show promise for production of high-quality bio-oil from Nannochloropsis via Ni-Ce/Al2O3 catalytic pyrolysis. Copyright © 2015 Elsevier Ltd. All rights reserved.

Antigenotoxicity of Dietary Coconut Oil

Directory of Open Access Journals (Sweden)

Clara Lim-Sylianco

1992-06-01

Full Text Available Benzo(apyrene, dimethylnitrosamine, methylmethanesulfonate and tetracycline induced formation of micronucleated polychromatic erythrocytes indicating that these substances are genotoxic to bone marrow cells of the experimental mice.Genotoxicity of these substances to germ cells was also observed when low fertility index and high percentage dead implants were induced in experimental mice.When each genotoxin was administered to mice fed with diets containing 18 % coconut oil for 23 days, the formation of micronucleated polychromatic erythrocytes was greatly reduced. Antigenotoxic activity of dietary coconut oil was very much greater than dietary soybean oil.Germ cell genotoxicity of each genotoxin was also reduced when male mice fed the 18 % coconut oil diet were used. When male mice treated with the genotoxin was mated with virgin females, fertility index was increased in the group fed with coconut oil diet. Percentage dead implants was reduced. The antigenotoxic activity of dietary coconut oil on germ cells far exceeds that of dietary soybean oil.Dietary restriction of coconut oil diets enhanced the antigenotoxic activity of coconut oil in bone marrow cells and germs cells.Among the triacylglycerols of coconut oil, trilaurin gave the best antigenotoxic activity in bone marrow cells. Trilaurin is the major triacylglycerol in coconut oil.

Somaclonal variation associated with oil palm (Elaeis guineensis ...

African Journals Online (AJOL)

aghomotsegin

2014-02-26

Feb 26, 2014 ... Malaysia and Indonesia together accounting for around. 83% of world palm oil production in 2001 (Wahid et al.,. 2004). The oil palm is an important economic crop, producing food and raw materials for the food, confectionary, cosmetics and ... inherently very slow, and high heterogeneity is still observed ...

Out of the Desert: My Journey from Nomadic Bedouin to the Heart of Global Oil

KAUST Repository

Al-Naimi, Ali Ibrahim

2017-01-08

His Excellency Ali Ibrahim Al-Naimi, former Ministry of Oil in the Kingdom of Saudi Arabia, will comment on his forthcoming autobiography "Out of the Desert: My Journey from Nomadic Bedouin to the Heart of Global Oil". Ali Ibrahim Al-Naimi is the former Saudi oil minister - and OPEC kingpin - a position he held for the two decades between August 1995 and May 2016. He was born into extreme poverty as a nomadic Bedouin in the 1930s, just as US companies were discovering vast quantities of oil under Arabian deserts. From his first job as a shepherd boy to his appointment to one of the most powerful political and economic jobs in the world, Out of the Desert charts Al-Naimi\\'s extraordinary rise to power.

Influence of Vegetable Oil-Based Controlled Cutting Fluid Impinging Supply System on Micro Hardness in Machining of Ti-6Al-4V

OpenAIRE

Salah Gariani; Islam Shyha; Fawad Inam; Dehong Huo

2017-01-01

A controlled cutting fluid impinging supply system (CUT-LIST) was developed to deliver an accurate amount of cutting fluid into the machining zone via well-positioned coherent nozzles based on a calculation of the heat generated. The performance of the CUT-LIST was evaluated against a conventional flood cutting fluid supply system during step shoulder milling of Ti-6Al-4V using vegetable oil-based cutting fluid. In this paper, the micro-hardness of the machined surface was used as the main cr...

Preparation and investigation of nano-AlN lubricant with high performance

Energy Technology Data Exchange (ETDEWEB)

Tao, Yu; Tao, Yuxiao; Wang, Biaobing [School of Materials Science and Engineering, Changzhou University, Changzhou 201326 (China); Tai, Yanlong, E-mail: ytai@ucdavis.edu [Department of Biomedical Engineering, University of California Davis, Davis, CA 95616 (United States)

2014-09-15

A new kind of macromolecular coupling agent (LMW-a-PP-g-MAH) of maleic anhydride (MAH) onto low-molecular-weight atactic polypropylene (LMW-a-PP) was synthesized according to molecular design and was used as modifier for surface modification of nano-Aluminum nitride (AlN) by a high-pressure homogenization (HPH) process. IR was conducted to confirm the chemical structure of the step products of LMW-a-PP-g-MAH. The availability as a modifier for surface modification of nano-AlN was distinguished by Fourier transform infrared spectroscopy (FTIR), particle size analysis, transmission electron microscope (TEM), thermogravimetric analysis (TGA), contact angle experiments and the dispersion stability in dimethylbenzene and Greatwall lubrication oil. It can be inferred that the optimal loading is 10 wt. %–12 wt. % of LMW-a-PP-g-MAH to modify nano-AlN particles. Nano-AlN lubricating composite materials (LMW-a-PP-g-MAH-AlN) was used to improve the antifriction performance and the load capability of Greatwall lubrication oil, and maximum non-seizure load (P{sub B}) can increase highly from 1000 N to 1490 N when the loading is 0.3 wt. %. - Highlights: • Design and synthesis of macromolecular coupling agent (a-PP-g-MAH). • Surface modification and characterization of nano-AlN by HPH process. • Preparation and investigation of nano-AlN/lubricating oil with high performance.

Method for enhanced oil recovery

Science.gov (United States)

Comberiati, Joseph R.; Locke, Charles D.; Kamath, Krishna I.

1980-01-01

The present invention is directed to an improved method for enhanced recovery of oil from relatively "cold" reservoirs by carbon dioxide flooding. In oil reservoirs at a temperature less than the critical temperature of 87.7.degree. F. and at a pore pressure greater than the saturation pressure of carbon dioxide at the temperature of the reservoir, the carbon dioxide remains in the liquid state which does not satisfactorily mix with the oil. However, applicants have found that carbon dioxide can be vaporized in situ in the reservoir by selectively reducing the pore pressure in the reservoir to a value less than the particular saturated vapor pressure so as to greatly enhance the mixing of the carbon dioxide with the oil.

Comparison of chemical characteristics of high oleic acid fraction of moringa oleifera oil with some vegetable oils

International Nuclear Information System (INIS)

Rahman, F.; Nadeem, M.; Zahoor, Y.

2014-01-01

Chemical characteristics of High oleic acid fraction (HOF) of Moringa oleifera oil (MOO) was compared with sunflower, soybean and canola oils. HOF of MOO was obtained by dry fractionation at 0 degree C. Iodine value and C18:1 in HOF increased from 61.55 to 82.47 points and 70.29% to 81.15%, respectively. Cloud point of HOF was 1.1 degree C as compared to 10.2 degree C in MOO. The induction period of HOF was greater than all the vegetable oils tested in this investigation. HOF can be used as a source of edible oil with better health attributes and superior storage stability. (author)

Grinding temperature and energy ratio coefficient in MQL grinding of high-temperature nickel-base alloy by using different vegetable oils as base oil

Directory of Open Access Journals (Sweden)

Li Benkai

2016-08-01

Full Text Available Vegetable oil can be used as a base oil in minimal quantity of lubrication (MQL. This study compared the performances of MQL grinding by using castor oil, soybean oil, rapeseed oil, corn oil, sunflower oil, peanut oil, and palm oil as base oils. A K-P36 numerical-control precision surface grinder was used to perform plain grinding on a workpiece material with a high-temperature nickel base alloy. A YDM–III 99 three-dimensional dynamometer was used to measure grinding force, and a clip-type thermocouple was used to determine grinding temperature. The grinding force, grinding temperature, and energy ratio coefficient of MQL grinding were compared among the seven vegetable oil types. Results revealed that (1 castor oil-based MQL grinding yields the lowest grinding force but exhibits the highest grinding temperature and energy ratio coefficient; (2 palm oil-based MQL grinding generates the second lowest grinding force but shows the lowest grinding temperature and energy ratio coefficient; (3 MQL grinding based on the five other vegetable oils produces similar grinding forces, grinding temperatures, and energy ratio coefficients, with values ranging between those of castor oil and palm oil; (4 viscosity significantly influences grinding force and grinding temperature to a greater extent than fatty acid varieties and contents in vegetable oils; (5 although more viscous vegetable oil exhibits greater lubrication and significantly lower grinding force than less viscous vegetable oil, high viscosity reduces the heat exchange capability of vegetable oil and thus yields a high grinding temperature; (6 saturated fatty acid is a more efficient lubricant than unsaturated fatty acid; and (7 a short carbon chain transfers heat more effectively than a long carbon chain. Palm oil is the optimum base oil of MQL grinding, and this base oil yields 26.98 N tangential grinding force, 87.10 N normal grinding force, 119.6 °C grinding temperature, and 42.7% energy

Transport of Blue Crab Larvae in the Northern Gulf of Mexico During the Deepwater Horizon Oil Spill

Science.gov (United States)

2015-05-11

the Deepwater Horizon (DWH) oil spill. The DWH spill, the largest accidental marine oil spill in US history (Graham et al. 2011), started when the...DWH oil platform, situ- ated 80 km southeast of Venice , Louisiana, ex- ploded and sank on 20 April 2010. An estimated 4.0 million barrels of oil...al. (1980). Using this ffiM together with spawning and larval behavior parameters from the known natural history of blue crabs, we ran 24

Effect of fast pyrolysis bio-oil from palm oil empty fruit bunch on bitumen properties

Science.gov (United States)

Poh, Chia Chin; Hassan, Norhidayah Abdul; Raman, Noor Azah Abdul; Shukry, Nurul Athma Mohd; Warid, Muhammad Naqiuddin Mohd; Satar, Mohd Khairul Idham Mohd; Ros Ismail, Che; Asmah Hassan, Sitti; Mashros, Nordiana

2018-04-01

Bitumen shortage has triggered the exploration of another alternative waste material that can be blended with conventional bitumen. This study presents the performance of pyrolysis bio-oil from palm oil empty fruit bunch (EFB) as an alternative binder in modified bitumen mixtures. The palm oil EFB was first pyrolyzed using auger pyrolyzer to extract the bio-oil. Conventional bitumen 80/100 penetration grade was used as a control sample and compared with samples that were modified with different percentages, i.e., 5% and 10%, of pyrolysis EFB bio-oil. The physical and rheological properties of the control and modified bitumen samples were investigated using penetration, softening point, viscosity and dynamic shear rheometer (DSR) tests. Results showed that the addition of EFB bio-oil softened the bitumen with high penetration and a reduction in softening point, penetration index, and viscosity. However, the DSR results showed a comparable rutting resistance between the bitumen samples containing EFB bio-oil and virgin bitumen with a failure temperature achieved greater than 64°C.

Treating oil in a maritime environment

International Nuclear Information System (INIS)

Seebacher, G.

2002-01-01

Some details of the International Maritime Organisation's marine pollution regulations are discussed. In simple terms, under IMO regulations oily water must be processed through approved equipment and can be legally discharged if the oil content in the treated effluent is less than 15 ppm. These regulations also make it clear that it is not permitted to use emulsifiers to hide the oil in the effluent. To separate the free oil from water, gravity enhanced separators can be used effectively. With conventional means it is possible to remove free oil from an oily water mixture, to the less than 15 part per million oil content. Conventional IMO certified oil content meters accurately read free oil content in the 0-30 ppm region, to prevent formation of an oil film from treated oily water discharges. Some additional basic rules of thumb worthy of consideration when separating oil from oily water: in general, it is cheaper to prevent oil discharge of oil into the effluent stream than to remove it; emulsifier-enriched lubricating oils emulsify readily and are difficult to remove when present in suspended droplets; the larger the amount of contamination, the greater the difficulty of removing the oil; an ounce of prevention is worth a pound of cure

Evaluating the use of PAO (4 cSt polyalphaoelfin) oil instead of DOP (di-octyl phthalate) oil for measuring the aerosol capture of nuclear canister filters

Energy Technology Data Exchange (ETDEWEB)

Moore, Murray E. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2014-07-18

This document details the distinction between using PAO (4 cSt polyalphaoelfin) oil instead of DOP (di-octyl phthalate) oil for measuring the aerosol capture of filters. This document is developed to justify the use of PAO rather than DOP for evaluating the performance of filters in the SAVY 4000 and Hagan containers. The design criteria (Anderson et al, 2012) for purchasing SAVY 4000 containers and the Safety Analysis Report for the SAVY 4000 Container Series specified that the filter must “capture greater than 99.97% of 0.45 μm mean diameter dioctyl phthalate (DOP) aerosol at the rated flow with a DOP concentration of 65±15 micrograms per liter.”This corresponds to a leakage percent of 0.03% (3.0x10^-2). The density of DOP oil is 985 kg/m³ and the density of PAO oil is 819 kg/m³. ATI Test Inc measured the mass mean diameter of aerosol distributions produced by a single Laskin type III-A nozzle operating at a 20 psig air pressure as 0.563 μm for DOP oil and 0.549 μm for PAO oil. (See Appendix A.) For both types of oil in this document, the single fiber method calculated the leakage percent to be 4.4x10^-5 for DOP oil and 4.7x10^-5 for PAO oil. Although the percent error between these two quantities is 7.7%, these calculated leakage percent values are more than two orders of magnitude less than the criterion specified in the SAVY canister SAR. As a point of reference, the photometer used to measure the SAVY canister filter performance cannot resolve values for the leakage percent below 1.0x10^-5. Additionally, over a range of particle sizes from 0.01 μm to 3.0 μm, there was less than 4.0x10^-5 error between the calculated filter efficiency for the two types of oil at any particular particle size diameter. In conclusion, the difference between using DOP and PAO for testing SAVY canister filters is of inconsequential concern.

Clay-oil flocculation and its role in natural cleansing in Prince William Sound following the Exxon Valdez oil spill

International Nuclear Information System (INIS)

Bragg, J.R.; Yang, S.H.

1995-01-01

Natural interactions of fine mineral particles with residue oil and seawater, in a process called clay-oil flocculation, were found to create solids-stabilized oil-in-water emulsions on shoreline sediments at numerous locations in Prince William Sound following the Exxon Valdez spill. In laboratory tests using oiled sediment samples from Prince William Sound, these emulsions were shown to facilitate natural cleansing and dispersion of oil from sediments by moving water. To investigate the effect of flocculation on natural cleansing, studies were conducted to determine the hydrodynamic energy needed for seawater to remove flocculated oil residues from sediments sampled from shorelines. Water was pumped at different velocities through a column packed with oiled sediment, and the amount and composition of oil removed from the sediment were measured as functions of water velocity and sediment movement. In separate tests, oil removal was observed in a wave tank that generated wave heights less than and greater than needed to move sediments. 28 refs., 13 figs., 7 tabs

Oil extracted from spent coffee grounds for bio-hydrotreated diesel production

International Nuclear Information System (INIS)

Phimsen, Songphon; Kiatkittipong, Worapon; Yamada, Hiroshi; Tagawa, Tomohiko; Kiatkittipong, Kunlanan; Laosiripojana, Navadol; Assabumrungrat, Suttichai

2016-01-01

Highlights: • The spent coffee oil with high FFAs was hydrotreated to liquid biofuel. • Pd/C gave higher olefins while NiMo/γ-Al_2O_3 gave higher isoparaffins liquid products. • The diesel fuel fraction can have a cetane number as high as 80. • The physiochemical properties of diesel fraction comply with commercial standard. - Abstract: Oil extracted from spent coffee grounds is utilized as a renewable source for bio-hydrotreated fuel production. In the present work, oil yield up to 13% can be obtained by Soxhlet extraction with hexane as a solvent. As the extracted oil contained high content of free fatty acids (6.14%), therefore one step alkali-catalyzed for ester based biodiesel production is impractical. Hydrotreating of extracted oil was performed over two catalysts i.e. NiMo/γ-Al_2O_3 and Pd/C with different operating parameters i.e. reaction time, operating temperature, and H_2/oil. It was found that the reaction time of 2 h and the reaction temperature of 400 °C are favorable operating conditions. The liquid products mostly consisted of n-pentadecane and n-heptadecane, which contain one carbon atom shorter than the corresponding fatty acid (C_n_−_1) i.e. palmitic and stearic acid, respectively. Unfavorable cracking of diesel product is pronounced at high temperature and prolonged reaction time. In addition, although increased H_2/oil promoted overall reaction and hydrodeoxygenation activity (C_n_−_1/C_n decreased) for both catalysts, hydrocracking is enhanced over Pd/C, leading to significant increase in gasoline yield. Moreover, Pd/C gave higher olefin content in liquid product (22.3 wt%) than NiMo/γ-Al_2O_3 (4.8 wt%). However, NiMo/γ-Al_2O_3 shows higher isomerization activity. The amount of isoparaffins catalyzed by NiMo/γ-Al_2O_3 and Pd/C were 10.8 and 1.7 wt%, respectively. Physiochemical analysis of the diesel fraction exhibit satisfactory properties. The density and kinematic viscosity were consistent with the specification of

Shale oil combustion

International Nuclear Information System (INIS)

Al-dabbas, M.A.

1992-05-01

A 'coutant' carbon steel combustion chamber cooled by water jacket was conslructed to burn diesel fuel and mixlure of shale oil and diesel fuels. During experimental work nir fuel ratio was determined, temperaturces were measured using Chromel/ Almel thermocouple, finally the gasous combustion product analysis was carricd out using gas chromatograph technique. The constructed combustion chamber was operating salisfactory for several hours of continous work. According to the measurements it was found that: the flame temperature of a mixture of diesel and shale oil fuels was greater than the flame temperature of diesel fuel. and the sulfer emissious of a mixture of diesel and shale oil fuels was higher than that of diesel fuel. Calculation indicated that the dry gas energy loss was very high and the incomplete combustion energy loss very small. (author). 23 refs., 35 figs

Shale oil combustion

Energy Technology Data Exchange (ETDEWEB)

Al-dabbas, M A

1992-05-01

A `coutant` carbon steel combustion chamber cooled by water jacket was conslructed to burn diesel fuel and mixlure of shale oil and diesel fuels. During experimental work nir fuel ratio was determined, temperaturces were measured using Chromel/ Almel thermocouple, finally the gasous combustion product analysis was carricd out using gas chromatograph technique. The constructed combustion chamber was operating salisfactory for several hours of continous work. According to the measurements it was found that: the flame temperature of a mixture of diesel and shale oil fuels was greater than the flame temperature of diesel fuel. and the sulfer emissious of a mixture of diesel and shale oil fuels was higher than that of diesel fuel. Calculation indicated that the dry gas energy loss was very high and the incomplete combustion energy loss very small. (author). 23 refs., 35 figs.

A study on wear resistance and microcrack of the Ti{sub 3}Al/TiAl + TiC ceramic layer deposited by laser cladding on Ti-6Al-4V alloy

Energy Technology Data Exchange (ETDEWEB)

Li Jianing, E-mail: ljnljn1022@163.com [Key Laboratory for Liquid-Solid Structural Evolution and Processing of Materials (Ministry of Education), Department of Materials Science, Shandong University, Jing Shi Road 17923, Jinan 250061, Shandong (China); Chen Chuanzhong [Key Laboratory for Liquid-Solid Structural Evolution and Processing of Materials, Ministry of Education, Department of Materials Science, Shandong University, Jing Shi Road 17923, Jinan 250061, Shandong (China); Squartini, Tiziano [INFM-Department of Physics, Siena University, Siena 53100 (Italy); He Qingshan [Key Laboratory for Liquid-Solid Structural Evolution and Processing of Materials, Ministry of Education, Department of Materials Science, Shandong University, Jing Shi Road 17923, Jinan 250061, Shandong (China)

2010-12-15

Laser cladding of the Al + TiC alloy powder on Ti-6Al-4V alloy can form the Ti{sub 3}Al/TiAl + TiC ceramic layer. In this study, TiC particle-dispersed Ti{sub 3}Al/TiAl matrix ceramic layer on the Ti-6Al-4V alloy by laser cladding has been researched by means of X-ray diffraction, scanning electron microscope, electron probe micro-analyzer, energy dispersive spectrometer. The main difference from the earlier reports is that Ti{sub 3}Al/TiAl has been chosen as the matrix of the composite coating. The wear resistance of the Al + 30 wt.% TiC and the Al + 40 wt.% TiC cladding layer was approximately 2 times greater than that of the Ti-6Al-4V substrate due to the reinforcement of the Ti{sub 3}Al/TiAl + TiC hard phases. However, when the TiC mass percent was above 40 wt.%, the thermal stress value was greater than the materials yield strength limit in the ceramic layer, the microcrack was present and its wear resistance decreased.

Rockets and Feathers: The Asymmetric Effect between China’s Refined Oil Prices and International Crude Oil Prices

Directory of Open Access Journals (Sweden)

Yufeng Chen

2017-03-01

Full Text Available This paper employs an asymmetric error-correction model (AECM, and uses monthly data on wholesale prices of gasoline and diesel products in China and international crude oil prices from February 2006 to October 2013 to examine whether China’s gasoline and diesel prices adjust asymmetrically to international crude oil price changes. Our empirical results suggest that increases and decreases in international oil prices have asymmetric effects on both wholesale prices of gasoline and diesel fuel in China, and that both increases and decreases in international oil prices have a greater effect on diesel prices than on gasoline prices in China. If there is no change in the maximum retail price, the asymmetry results from the transmission of wholesale prices in China with international oil prices. However, if there is a change in maximum retail prices, both international oil prices and maximum retail prices cause the asymmetry.

Diesel oil combustion in fluidized bed; Combustion de aceite diesel en lecho fluidizado

Energy Technology Data Exchange (ETDEWEB)

Rodriguez Cazares, Mario [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

1992-07-01

The effect of the fluidized bed depth in the combustion in burning diesel oil in a fluidized bed, was analyzed. A self sustained combustion was achieved injecting the oil with an injector that utilized a principle similar to an automobile carburetor venturi. Three different depths were studied and it was found that the deeper the bed, the greater the combustion efficiency. Combustion efficiencies were attained from 82% for a 100mm bed depth, up to 96% for a 200mm bed depth. The diminution in the efficiency was mainly attributed to unburned hydrocarbons and to the carbon carried over, which was observed in the black smoke at the stack outlet. Other phenomena registered were the temperature gradient between the lower part of the bed and the upper part, caused by the fluidization velocity; additionally it was observed that the air employed for the oil injection (carbureting air) is the most important parameter to attain a complete combustion. [Espanol] Se analizo el efecto de la profundidad del lecho en la combustion al quemar aceite diesel en un lecho fluidizado experimental. Se logro combustion autosostenida inyectando el aceite con un inyector que utilizo un principio similar al venturi del carburador de automovil. Se estudiaron tres diferentes profundidades del lecho y se encontro que a mayor profundidad del lecho, mayor eficiencia de la combustion. Se lograron eficiencias de la combustion desde 82% para el lecho de 100 mm de profundidad hasta 96% para el de 200 mm. La disminucion de la eficiencia se atribuyo, principalmente, a los hidrocarburos no quemados y al carbon arrastrado, lo cual se observo en el humo negro a la salida de la chimenea. Otros fenomenos registrados fueron el gradiente de temperatura entre la parte baja del lecho y la parte superior causado por la velocidad de fluidizacion; ademas, se observo que el aire utilizado para inyectar el aceite (aire de carburacion) es el parametro mas importante para lograr una combustion completa.

Catalytic flash pyrolysis of oil-impregnated-wood and jatropha cake using sodium based catalysts

KAUST Repository

Imran, Ali

2015-11-24

Catalytic pyrolysis of wood with impregnated vegetable oil was investigated and compared with catalytic pyrolysis of jatropha cake making use of sodium based catalysts to produce a high quality bio-oil. The catalytic pyrolysis was carried out in two modes: in-situ catalytic pyrolysis and post treatment of the pyrolysis vapors. The in-situ catalytic pyrolysis was carried out in an entrained flow reactor system using a premixed feedstock of Na2CO3 and biomass and post treatment of biomass pyrolysis vapor was conducted in a downstream fixed bed reactor of Na2CO3/γ-Al2O3. Results have shown that both Na2CO3 and Na2CO3/γ-Al2O3 can be used for the production of a high quality bio-oil from catalytic pyrolysis of oil-impregnated-wood and jatropha cake. The catalytic bio-oil had very low oxygen content, water content as low as 1wt.%, a neutral pH, and a high calorific value upto 41.8MJ/kg. The bio-oil consisted of high value chemical compounds mainly hydrocarbons and undesired compounds in the bio-oil were either completely removed or considerably reduced. Increasing the triglycerides content (vegetable oil) in the wood enhanced the formation of hydrocarbons in the bio-oil. Post treatment of the pyrolysis vapor over a fixed bed of Na2CO3/γ-Al2O3 produced superior quality bio-oil compared to in-situ catalytic pyrolysis with Na2CO3. This high quality bio-oil may be used as a precursor in a fractionating process for the production of alternative fuels. © 2015 Elsevier B.V.

Principles of heavy oil recovery

Energy Technology Data Exchange (ETDEWEB)

Szasz, S.E.; Thomas, G.W.

1965-10-01

Rising exploration costs have prompted greater interest in the large known deposits of heavy oil in North America. Because of high oil viscosities in such reservoirs, recoveries are poor, fluid drives are inefficient and production rates are uneconomical. Viscosity reduction can best be accomplished by heating the reservoir. The basic aspects of reservoir heating are reviewed and those processes which are of practical importance in heavy oil reservoirs are discussed. Wellbore heating frequently can be applied to heavy oil reservoirs to increase production rates. In hot waterflooding, the water requirements are much higher than an ordinary waterflood. Steam floods are more attractive, but operating costs are generally high. Conduction heating processes appear most promising. Among these is included the cyclic steam-soak process. A simple method is presented for estimating the performance from the first cycle of steam injection into the formation, assuming gravity as the only driving energy. An example calculation for a typical heavy oil reservoir is given. (26 refs.)

Analysis of the kerogen of oil shales

Energy Technology Data Exchange (ETDEWEB)

Quass, F W; Down, A L

1939-01-01

Comments are given on the method developed by F. W. Quass for reducing the amount of mineral matter present in certain coals and oil shales (torbanites). The method consisted of grinding oil shale with water in a porcelain ball mill in the presence of oil. The oil formed a paste with the carbonaceous material, and a greater portion of the mineral matter remained suspended in the water and was separated. Ultimate analyses of the enriched samples indicated that the percent of carbon was higher, the percent of hydrogen and oxygen was lower, and the ratio of carbon to hydrogen and carbon to oxygen increased in the enriched samples.

A Study on the Preparation of Regular Multiple Micro-Electrolysis Filler and the Application in Pretreatment of Oil Refinery Wastewater.

Science.gov (United States)

Yang, Ruihong; Zhu, Jianzhong; Li, Yingliu; Zhang, Hui

2016-04-29

Through a variety of material screening experiments, Al was selected as the added metal and constituted a multiple micro-electrolysis system of Fe/C/Al. The metal proportion of alloy-structured filler was also analyzed with the best Fe/C/Al ratio of 3:1:1. The regular Fe/C/Al multiple micro-electrolysis fillers were prepared using a high-temperature anaerobic roasting method. The optimum conditions for oil refinery wastewater treated by Fe/C/Al multiple micro-electrolysis were determined to be an initial pH value of 3, reaction time of 80 min, and 0.05 mol/L Na₂SO₄ additive concentration. The reaction mechanism of the treatment of oil refinery wastewater by Fe/C/Al micro-electrolysis was investigated. The process of the treatment of oil refinery wastewater with multiple micro-electrolysis conforms to the third-order reaction kinetics. The gas chromatography-mass spectrometry (GC-MS) used to analyze the organic compounds of the oil refinery wastewater before and after treatment and the Ultraviolet-visible spectroscopy (UV-VIS) absorption spectrum analyzed the degradation process of organic compounds in oil refinery wastewater. The treatment effect of Fe/C/Al multiple micro-electrolysis was examined in the continuous experiment under the optimum conditions, which showed high organic compound removal and stable treatment efficiency.

Effects of Microwave Radiation on Oil Recovery

Science.gov (United States)

Esmaeili, Abdollah

2011-12-01

A variety of oil recovery methods have been developed and applied to mature and depleted reservoirs in order to improve the efficiency. Microwave radiation oil recovery method is a relatively new method and has been of great interest in the recent years. Crude oil is typically co-mingled with suspended solids and water. To increase oil recovery, it is necessary to remove these components. The separation of oil from water and solids using gravitational settling methods is typically incomplete. Oil-in-water and oil-water-solid emulsions can be demulsified and separated into their individual layers by microwave radiation. The data also show that microwave separation is faster than gravity separation and can be faster than conventional heating at many conditions. After separation of emulsion into water and oil layers, water can be discharged and oil is collected. High-frequency microwave recycling process can recover oil and gases from oil shale, residual oil, drill cuttings, tar sands oil, contaminated dredge/sediments, tires and plastics with significantly greater yields and lower costs than are available utilizing existing known technologies. This process is environmentally friendly, fuel-generating recycler to reduce waste, cut emissions, and save energy. This paper presents a critical review of Microwave radiation method for oil recovery.

Noble Gas signatures of Enhanced Oil Recovery

Science.gov (United States)

Barry, P. H.; Kulongoski, J. T.; Tyne, R. L.; Hillegonds, D.; Byrne, D. J.; Landon, M. K.; Ballentine, C. J.

2017-12-01

Noble gases are powerful tracers of fluids from various oil and gas production activities in hydrocarbon reservoirs and nearby groundwater. Non-radiogenic noble gases are introduced into undisturbed oil and natural gas reservoirs through exchange with formation waters [1-3]. Reservoirs with extensive hydraulic fracturing, injection for enhanced oil recovery (EOR), and/or waste disposal also show evidence for a component of noble gases introduced from air [4]. Isotopic and elemental ratios of noble gases can be used to 1) assess the migration history of the injected and formation fluids, and 2) determine the extent of exchange between multiphase fluids in different reservoirs. We present noble gas isotope and abundance data from casing, separator and injectate gases of the Lost Hills and Fruitvale oil fields in the San Joaquin basin, California. Samples were collected as part of the California State Water Resource Control Board's Oil and Gas Regional Groundwater Monitoring Program. Lost Hills (n=7) and Fruitvale (n=2) gases are geochemically distinct and duplicate samples are highly reproducible. Lost Hills casing gas samples were collected from areas where EOR and hydraulic fracturing has occurred in the past several years, and from areas where EOR is absent. The Fruitvale samples were collected from a re-injection port. All samples are radiogenic in their He isotopes, typical of a crustal environment, and show enrichments in heavy noble gases, resulting from preferential adsorption on sediments. Fruitvale samples reflect air-like surface conditions, with higher air-derived noble gas concentrations. Lost Hills gases show a gradation from pristine crustal signatures - indicative of closed-system exchange with formation fluids - to strongly air-contaminated signatures in the EOR region. Pristine samples can be used to determine the extent of hydrocarbon exchange with fluids, whereas samples with excess air can be used to quantify the extent of EOR. Determining noble

Oil scenarios; Escenarios petroleros

Energy Technology Data Exchange (ETDEWEB)

Quiros Corradi, Alberto [Oxford Energy Policy Club (United States)

2003-04-15

If there is a war in Middle East affecting the Saudi Arabian crude oil production, the crude oil prices will increase at unimaginable levels. This is due to both the current decrease of the production capacity of Venezuela and the Nigeria's political fragility. Therefore, despite the fact that the majority of the reasons why the United States invade Irak are unknown, it is clear that the crude oil is one of them and is playing a major role. [Spanish] Cualesquiera que sean las verdaderas razones de Estados Unidos para invadir Irak, esta claro que el petroleo tiene un papel muy importante. Una guerra en Medio Oriente que afectara la produccion petrolera de Arabia Saudita elevaria los precios del crudo a niveles nunca vistos, debido al actual descenso de la capacidad de produccion de Venezuela y a la fragilidad politica de Nigeria.

Mineral catalysis of oil producing reactions in coal liquefaction

Energy Technology Data Exchange (ETDEWEB)

Shridharani, K.G.

1983-01-01

This work was concerned primarily with the development of a relatively inexpensive, readily available, high activity catalyst that can be used as a disposable catalyst in coal liquefaction processes. For a fair evaluation of the developmental mineral catalyst (presulfided iron oxide), it was necessary to determine at different stages of this work, whether catalyst inhibition, deactivation or activity was the limiting factor in coal liquefaction catalysis. First, different routes were explored to prepare a high hydrogenation activity, iron-based catalyst. Naphthalene hydrogenation was used as a model reaction to rate the hydrogenation activities of different additives. Presulfiding of iron oxide with H/sub 2/S, under controlled conditions, rendered the highest hydrogenation activity mineral catalyst, which had a hydrogenation activity even greater than that of commercial CoMo/Al/sub 2/O/sub 3/ catalyst sulfided with creosote oil and hydrogen. Sulfiding of CoMo/Al/sub 2/O/sub 3/ catalyst with H/sub 2/S remarkably improved its initial hydrogenation activity. Second, the catalyst inhibition and deactivation during liquefaction were studied. Liquefaction-process solvents contain a number of compounds that can either deactivate or inhibit the hydrogenation activity of a catalyst. Finally, the hydrocracking activity of the presulfided iron oxide catalyst was compared with that of commercial catalysts, CoMo/Al/sub 2/O/sub 3/ and low alumina FCC catalyst.

Studies on the improvement of the components of essential oil of genus Mentha by radiation

International Nuclear Information System (INIS)

Ono, Seiroku

1980-01-01

M. arvensis L. var. piperascens M sub(AL). (2 n = 96, R sup(a)Rsup(a)SS JJ AA, main component menthol) as the material the elucidation of biosynthetic mechanisms of essential oil was attempted. As the result it has been demonstrated that the biosynthesis is completed between 84 - 86 days after placing individual cells in the culture medium, especially on 85 days. Such an elucidation serves as the criteria of the biosynthetic pathway elucidation and it is the first accomplishment in the world. Next, the irradiation with γ-rays of 55R/min, total dose 19.5 KR gives a marked effect, and by this method a new plant (rose mint) having aroma similar to rose oil has been established, and this new plant has been designated as ''rose mint.'' This new improved plant can yield about 1 Kg of essential oil from 30 Kg of plant, and in comparing to 1 Kg of essential oil obtained from about 10 6 rose flowers by the conventional method, the yield is enormously greater and its wide application can be expected in the future. This newly developed breeding method can be also applied to other plants where the extraction of the plant compositions is desired, and at present this method is applied to the Perilla by which a new plant having sweet taste has been successfully established. (author)

/Cu-Al System

Science.gov (United States)

Kish, Orel; Froumin, Natalya; Aizenshtein, Michael; Frage, Nachum

2014-05-01

Wettability and interfacial interaction of the Ta2O5/Cu-Al system were studied. Pure Cu does not wet the Ta2O5 substrate, and improved spreading is achieved when relatively a high fraction of the active element (~40 at.% Al) was added. The Al2O3 and AlTaO4 phases were observed at the Ta2O5/Cu-Al interface. A thermodynamic evaluation allowed us to suggest that the lack of wetting bellow 40 at.% Al is due to the presence of a native oxide, which covers the drop. The conditions of the native oxide decomposition and the formation of the volatile Al2O suboxide strongly depend on the vacuum level during sessile drop experiments and the composition of the Cu-Al alloy. In our case, Al contents greater than 40% provides thermodynamic conditions for the formation of Al2O (as a result of Al reaction with Al2O3) and the drop spreading. It was suggested that the final contact angle in the Ta2O5/Cu-Al system (50°) is determined by Ta adsorption on the newly formed alumina interlayer.

Antioxidant effect of poleo and oregano essential oil on roasted sunflower seeds.

Science.gov (United States)

Quiroga, Patricia R; Grosso, Nelson R; Nepote, Valeria

2013-12-01

The objective was to evaluate the stability of sensory and chemical parameters in roasted sunflower seeds supplemented with oregano and poleo essential oils; and the consumer acceptability of this product. Four samples were prepared: plain roasted sunflower seeds (Control = RS-C), and sunflower seeds added with oregano (RS-O) or poleo (RS-P) essential oils or BHT (RS-BHT). Consumer acceptance was determined on fresh samples. The overall acceptance averages were 6.13 for RS-C, 5.62 for RS-P, and 5.50 for RS-O (9-point hedonic scale). The addition of BHT showed greater protection against the oxidation process in the roasted sunflower seeds. Oregano essential oil exhibited a greater antioxidant effect during storage than poleo essential oil. Both essential oils (oregano and poleo) provided protection to the product, inhibiting the formation of undesirable flavors (oxidized and cardboard). The antioxidant activity that presents essential oils of oregano and poleo could be used to preserve roasted sunflower seeds. © 2013 Institute of Food Technologists®

Effectiveness of dispersants on thick oil slicks

International Nuclear Information System (INIS)

Ross, S.; Belore, R.

1993-01-01

Experiments were conducted to determine the relationship between dispersant effectiveness and oil slick thickness, and thereby determine the optimum time for applying dispersant onto spilled oil at sea. Tests were completed at a lab-scale level by varying the three parameters of oil type, dispersant application, and oil thickness. The tests were intended to be comparative only. The primary oils used were Alberta sweet mix blend and Hibernia B-27 crude. The dispersant, Corexit 9527, was applied either premixed with the oil, dropwise in one application, or dropwise in multiple applications to simulate a multi-hit aircraft operation. The apparatus used in the experiment was an oscillating hoop tank, with oil-containing rings used to obtain and maintain uniform slick thickness. The results indicate that the effectiveness potential of a chemical dispersant does not decrease as slick thickness increases. In fact, results of the tests involving Hibernia oil suggest that oils that tend to herd easily would be treated more effectively if dispersant were applied when the oil was relatively thick (1 mm or greater) to avoid herding problems. The oil slicks premixed with dispersant did not disperse well in the thick oil tests, not because of dispersant-oil interaction problems but because of reduced mixing energy. 6 refs., 4 figs., 1 tab

Removal of colour, turbidity, oil and grease for slaughterhouse wastewater using electrocoagulation method

Science.gov (United States)

Yusoff, Mohd Suffian; Azwan, Azlyza Mohd; Zamri, Mohd Faiz Muaz Ahmad; Aziz, Hamidi Abdul

2017-10-01

In this study electrocoagulation method is used to treat slaughterhouse wastewaters. The aim of this study is to determine the efficiency of electrocoagulation method for the removal of colour, turbidity, oil and grease of slaughterhouse wastewaters. The factors of electrode types, and voltage applied during treatment are the study parameters. The types of electrode used are Aluminium (Al) grade 6082 and Iron (Fe) grade 1050. Meanwhile, the ranges of voltage applied are 2, 4, 6, 8 volts at a time interval of 10, 20 and 30 minutes respectively. The effect of these factors on the removal of fat oil and grease (FOG), colour and turbidity are analyzed. The results show maximum removal of FOG, colour and turbidity are recorded using Fe electrode at 8 V of applied voltage with 30 minutes of treatment time. The increase in treatment time of the cell will also increase the amount of hydrogen bubbles at the cathode which results in a greater upwards flux and a faster removal of FOG,, turbidity and colour. The removal of FOG, colour and turbidity are 98%, 92% and 91 % respectively. Meanwhile, by using Al electrodes in the same condition, the removal of FOG, colour and turbidity are 91%, 85% and 87 % respectively. Whereas by using Fe-Al as electrodes pairs, the removal of FOG, colour and turbidity are found to be at 90%, 87% and 76 % respectively. In this case, the Fe-Fe pair electrodes have been proven to provide better performance for FOG, colour and turbidity removals of slaughterhouse wastewaters. Therefore, it is feasible to be considered as an alternative method for wastewater treatment.

Production of bio-hydrogenated diesel by catalytic hydrotreating of palm oil over NiMoS2/γ-Al2O3 catalyst.

Science.gov (United States)

Srifa, Atthapon; Faungnawakij, Kajornsak; Itthibenchapong, Vorranutch; Viriya-Empikul, Nawin; Charinpanitkul, Tawatchai; Assabumrungrat, Suttichai

2014-04-01

Catalytic hydrotreating of palm oil (refined palm olein type) to produce bio-hydrogenated diesel (BHD) was carried out in a continuous-flow fixed-bed reactor over NiMoS2/γ-Al2O3 catalyst. Effects of dominant hydrotreating parameters: temperature: 270-420°C; H2 pressure: 15-80 bar; LHSV: 0.25-5.0 h(-1); and H2/oil ratio: 250-2000 N(cm(3)/cm(3)) on the conversion, product yield, and a contribution of hydrodeoxygenation (HDO) and decarbonylation/decarboxylation (DCO/DCO2) were investigated to find the optimal hydrotreating conditions. All calculations including product yield and the contribution of HDO and DCO/DCO2 were extremely estimated based on mole balance corresponding to the fatty acid composition in feed to fully understand deoxygenation behaviors at different conditions. These analyses demonstrated that HDO, DCO, and DCO2 reactions competitively occurred at each condition, and had different optimal and limiting conditions. The differences in the hydrotreating reactions, liquid product compositions, and gas product composition were also discussed. Copyright © 2014 Elsevier Ltd. All rights reserved.

Hydrodeoxygenation of furfuryl alcohol over Cu/MgAl and Cu/ZnAl catalysts derived from hydrotalcite-like precursors

Directory of Open Access Journals (Sweden)

Natalia Andrea Pino

2017-01-01

Full Text Available The aqueous phase hydrodeoxygenation (HDO of furfuryl alcohol over Cu/MgAl and Cu/ZnAl catalysts with different Mg/Al and Zn/Al molar ratios, were investigated. Mg-Al and Zn-Al mixed oxides derived from hydrotalcites precursors were used as supports, which were impregnated with an aqueous solution of copper nitrate by incipient wetness impregnation. The HDO reaction was carried out in a typical batch reactor at 5 MPa of H2 and 200 °C for 4 h. Among the catalysts studied, the Cu/MgAl-0.5 catalyst exhibited the higher furfuryl alcohol conversion (86% and yield of cyclopentanol (35%, which is the reaction product with the highest hydrogen-carbon (H/C ratio. With the Cu/MgAl-3 catalyst a high cyclopentanone yield (67% was achieved. The results obtained, showed that copper supported on mixed oxides catalysts derived from hydrotalcite precursors are a promising alternative to improve the bio-oil quality.

Corrosion behavior of Cu Al Ni shape memory alloy in an oil land field produced fluid; Corrosao da liga com memoria de forma CuAlNi em fluido produzido de campo terrestre de petroleo

Energy Technology Data Exchange (ETDEWEB)

Souza, Ricardo Estefany Aquino [PETROBRAS S.A., Aracaju/Maceio, SE/AL (Brazil). Unidade de Negocios SE-AL; Cruz, Maria Clara Pinto; Figueiredo, Renan T.; Souza, Luciete da Paixao; Araujo, Paulo M.M. [Universidade Tiradentes (UNIT), Aracaju, SE (Brazil)

2008-07-01

The corrosion behavior of the CuAlNi shape memory alloy in oil landfield produced groundwater was investigated with polarization curve and mass loss measurements, the latter carried out by immersion in laboratory and field tests. The physico-chemical analysis of five types of oil landfield produced groundwater showed the presence of H{sub 2}S and CO{sub 2}, high salinity, chloride, sulfide and iron ions and relatively neutral pH. The results from electrochemical tests in aerated produced groundwater, in the range of salinity encountered, suggested that the corrosion rate increases at higher saline concentrations. The results from field tests with corrosion test specimens showed a moderate to severe corrosion rate and suggested, in the other hand, that corrosion rates were influenced not only by salinity and oxidizing ions present in the flowing fluid, but also by solid materials in suspension, the fluid's temperature, and the flow velocity. This research is part of a major project which aims to develop couplings for landfield produced fluid transportation pipe connections without welded nor threaded joints. (author)

Financial Times oil and gas international year book 1994

International Nuclear Information System (INIS)

Williams, Julian

1993-01-01

The greater part of this book aims to provide narrative, production and financial details of major oil and gas companies, both upstream and downstream, across the world. Smaller sections give details on major oil and gas brokers and traders, and on the principal oil and gas associations. These sections are arranged alphabetically by company name. A geographical index towards the end of the book enables the user to identify upstream companies exploring for or producing oil and gas in particular areas. The company index includes every company mentioned in the book and includes all subsidiary and related companies to the major companies. Four introductory tables give data on world petroleum production, oil refining, tanker tonnage and oil consumption. (Author)

The evaporative drying of sludge by immersion in hot oil: Effects of oil type and temperature

Energy Technology Data Exchange (ETDEWEB)

Ohm, Tae-In, E-mail: tiohm1@hanbat.ac.kr [Department of Environmental Engineering, Hanbat National University, San 16-1 Duckmyung-dong, Yusung-gu, Daejeon 305-719 (Korea, Republic of); Chae, Jong-Seong; Lim, Kwang-Soo [Department of Environmental Engineering, Hanbat National University, San 16-1 Duckmyung-dong, Yusung-gu, Daejeon 305-719 (Korea, Republic of); Moon, Seung-Hyun [Waste Energy Research Center, Korea Institute of Energy Research, Jang-dong Yusung-gu, Daejeon 305-343 (Korea, Republic of)

2010-06-15

We investigated the evaporative drying by immersion in hot oil (EDIHO) method for drying sludge. This involved heating oil to a temperature higher than that needed for moisture to be evaporated from the sludge by turbulent heat and mass transfer. We fry-dried sewage and leather plant sludge for 10 min in each of four different oils (waste engine, waste cooking, refined waste, and B-C heavy) and three different temperatures (140 deg. C, 150 deg. C, and 160 deg. C). Drying efficiency was found to be greater for higher temperatures. However, giving consideration to energy efficiency we suggest that the optimal temperature for fry-drying sludge is 150 deg. C. At 150 deg. C, the water content of sewage sludge reduced from 78.9% to between 1.5% (with waste cooking oil) and 3.8% (with waste engine oil). The reduction in water content for leather plant sludge fry-dried at 150 deg. C was from 81.6% to between 1% (with waste cooking oil) and 6.5% (with refined waste oil). The duration of the constant rate-drying period was also influenced by the type of oil used: refined waste oil > waste engine oil > B-C heavy oil > waste cooking oil. The duration at 150 deg. C with waste cooking oil was 3 min for sewage sludge and 2 min for leather plant sludge. It is likely that the drying characteristics of oil are influenced by its thermal properties, including its specific heat, and molecular weight.

The evaporative drying of sludge by immersion in hot oil: Effects of oil type and temperature

International Nuclear Information System (INIS)

Ohm, Tae-In; Chae, Jong-Seong; Lim, Kwang-Soo; Moon, Seung-Hyun

2010-01-01

We investigated the evaporative drying by immersion in hot oil (EDIHO) method for drying sludge. This involved heating oil to a temperature higher than that needed for moisture to be evaporated from the sludge by turbulent heat and mass transfer. We fry-dried sewage and leather plant sludge for 10 min in each of four different oils (waste engine, waste cooking, refined waste, and B-C heavy) and three different temperatures (140 deg. C, 150 deg. C, and 160 deg. C). Drying efficiency was found to be greater for higher temperatures. However, giving consideration to energy efficiency we suggest that the optimal temperature for fry-drying sludge is 150 deg. C. At 150 deg. C, the water content of sewage sludge reduced from 78.9% to between 1.5% (with waste cooking oil) and 3.8% (with waste engine oil). The reduction in water content for leather plant sludge fry-dried at 150 deg. C was from 81.6% to between 1% (with waste cooking oil) and 6.5% (with refined waste oil). The duration of the constant rate-drying period was also influenced by the type of oil used: refined waste oil > waste engine oil > B-C heavy oil > waste cooking oil. The duration at 150 deg. C with waste cooking oil was 3 min for sewage sludge and 2 min for leather plant sludge. It is likely that the drying characteristics of oil are influenced by its thermal properties, including its specific heat, and molecular weight.

Catalytic Synthesis of Ethyl Ester From Some Common Oils ...

African Journals Online (AJOL)

Catalytic conversion of ethanol to fatty acid ethyl esters (FAEE) was carried out by homogeneous and heterogeneous transesterification of melon seed, shea butter and neem seed oils using NaOH, KOH and 5wt%CaO/Al2O3 catalyst systems respectively. Oil content of the seeds from n-hexane or hot water extract ranged ...

Characterization of constituents, quality and stability of pomegranate seed oil (Punica granatum L.

Directory of Open Access Journals (Sweden)

Illana Louise Pereira de MELO

2016-03-01

Full Text Available Abstract This study aimed to characterize pomegranate seed oil and evaluate its quality and stability parameters against those of linseed oil. The profile of fatty acids and phytosterols and the content of tocopherols were analyzed by gas chromatography and high performance liquid chromatography, respectively. The quality of both oils was assessed as recommended by the American Oil Chemists' Society (AOCS and stability was evaluated using 2,2-diphenyl-1-picrylhydrazyl (DPPH, β-carotene bleaching (coupled oxidation of β-carotene/linoleic acid and Rancimat® assays. While α-linolenic acid (52% was the most abundant fatty acid in linseed oil (LO, punicic acid (55% was highest in pomegranate seed oil (PSO. Tocopherols and phytosterols (175 and 539 mg/100 g, respectively were greater in PSO than in LO (51 and 328 mg/100 g, respectively. Both oils met quality standards. The β-carotene bleaching and the DPPH assays showed greater oxidative stability for PSO than for LO. The Rancimat® method, on the other hand, indicated low stability for both oils.

Oil Slick Characterization with UAVSAR

Science.gov (United States)

Jones, C. E.; Holt, B.

2017-12-01

Although radar has long been used for mapping the spatial extent of oil slicks, its capability for characterizing oil, e.g., to discriminate thicker from thinner oil or mineral slicks from look-alikes, is far less well defined. In fact, the capability of SAR to quantify the oil-to-water ratio of emulsions within slicks on the open water was first demonstrated using UAVSAR data acquired over the 2010 Deepwater Horizon spill in the Gulf of Mexico [Minchew et al., 2012]. UAVSAR's capability was made possible by the airborne instrument's high signal-to-noise ratio, which enabled it to measure low backscatter signals from oil-smoothed water that are often near or below the noise floor of satellite SAR instruments. Since 2010, UAVSAR has been used to study oil slicks through experiments in Norway (2015) and the Gulf of Mexico. In November 2016, UAVSAR took part in a NOAA-led experiment to study remote sensing of oil slicks, which took place at the site of a persistent seep in the Gulf of Mexico. The goal was to use remote sensing to identify zones of thicker oil, which is the type of information that could direct emergency responders for more effective clean-up. The objectives of the experiment were to validate and compare different remote sensing methods' capabilities for measuring the thickness of oil within a slick on open water under environmental conditions typical of oil spills. In this presentation, we show the results from UAVSAR for determining oil thickness within a slick, and relate them to the standard method of oil slick classification, the Bonn Agreement oil appearance code used by trained observers in the field. This work was carried out in part at the Jet Propulsion Laboratory, California Institute of Technology, under contracts with the California Dept. of Water Resources and with the National Aeronautics and Space Administration.

Oil in Ice Project Final Report

Science.gov (United States)

2018-03-01

Great Lakes, as well as technology exclusively demonstrated in the Arctic (RDC, 2012; GPC, 2012; Hansen, 2012; Hansen, et al., 2014; Story et. al. 2015...2010. Story , J., Tripp, S., Jenkins, S., Decker, D., Hastings, D.J., and Dunn, S. (2015) “After Action Report – Arctic Technology Evaluation 2015...The CG needs better technologies for responding to oil spills in these extreme cold weather environments both in the Arctic and the northern

Soybean (Glycine max) oil bodies and their associated phytochemicals.

Science.gov (United States)

Fisk, Ian D; Gray, David A

2011-01-01

Soybean oil bodies were isolated from 3 cultivars (Ustie, K98, and Elena) and the occurrence of 2 classes of phytochemicals (tocopherol isoforms and isoflavones) and strength of their association with isolated oil bodies was evaluated. Tocopherol is shown to be closely associated with soybean oil bodies; δ-tocopherol demonstrated a significantly greater association with oil bodies over other tocopherol isoforms. Isoflavones do not show a significant physical association with oil bodies, although there is some indication of a passive association of the more hydrophobic aglycones during oil body isolation. Oil bodies are small droplets of oil that are stored as energy reserves in the seeds of oil seeds, and have the potential to be used as future food ingredients. If oil body suspensions are commercialized on a large scale, knowledge of the association of phytochemicals with oil bodies will be valuable in deciding species of preference and predicting shelf life and nutritional value. © 2011 Institute of Food Technologists®

Production and refining of Dacryodes edulis “native pear” seeds oil

African Journals Online (AJOL)

STORAGESEVER

2008-05-02

May 2, 2008 ... ml/g). Bleaching of 0.2% Na2CO3 degummed oil resulted in oil with peroxide value of 20 mgEq/Kg which ... Nigeria, Liberia, Cameroons and Zaire (Boungou, et al., .... Hui YJ Ed., John Wiley and Sons ... Robert Maxwell, pp.

NFDRSPC: The National Fire-Danger Rating System on a Personal Computer

Science.gov (United States)

Bryan G. Donaldson; James T. Paul

1990-01-01

This user's guide is an introductory manual for using the 1988 version (Burgan 1988) of the National Fire-Danger Rating System on an IBM PC or compatible computer. NFDRSPC is a window-oriented, interactive computer program that processes observed and forecast weather with fuels data to produce NFDRS indices. Other program features include user-designed display...

Antioxidant and pro-oxidant factors in oregano and rosemary gourmet olive oils

Directory of Open Access Journals (Sweden)

Tsimidou, Maria

2001-08-01

Full Text Available The study was carried out to examine the presence of antioxidants and pro-oxidants in oregano and rosemary gourmet oils. Dry, ground plant material (5% w/w was infused to olive oil for 24, 48 and 72 hours and then it was removed by filtration. All preparations were found acceptable using a panel test. The total polar phenol content increased 3.5 and 1.7 times in oregano and rosemary gourmet oils with respect to that of the control sample. A qualitative enrichment of the methanol:water fraction of olive oil with phenolic compounds from herbs were found using HPLC. No rosmarinic acid was detected in the gourmet oils. Vanillic acid was only found in the rosemary gourmet oil. The presence of flavonoids was assessed using TLC. a-Tocopherol content of the oil matrix was not changed after herb infusion. A significant increase was found in pheophytin, a,b-carotene and lutein content of oregano flavoured oils. The oxidative stability of gourmet oils was greater to that of the control using the Rancimat test. In photo-oxidation, oregano flavoured oil was less stable than the rosemary one. Total chlorophyll content may be a critical factor for the shelf life of these preparations. Suitable labelling suggesting avoidance of light may be useful for a safe domestic use.El estudio fue realizado para examinar la presencia de antioxidantes y pro-oxidantes en aceites de oliva con aroma a orégano y romero. El material vegetal seco y molido se añade al aceite de oliva en proporción (5% w/w durante 24, 48 y 72 horas y posteriormente se elimina por filtración. Todas las preparaciones se encontraron aceptables usando un panel de catadores. El contenido de fenoles polares totales aumentó 3,5 y 1,7 veces, en aceites con aroma a orégano y romero, con respecto al de las muestras control. Un enriquecimiento cualitativo de la fracción metanol: agua del aceite de oliva, con compuestos fenólicos de las hierbas, se encontró usando HPLC. No se detectó �

Analysis of edible oil processing options for the BIO-Plex advanced life support system

Science.gov (United States)

Greenwalt, C. J.; Hunter, J.

2000-01-01

Edible oil is a critical component of the proposed plant-based Advanced Life Support (ALS) diet. Soybean, peanut, and single-cell oil are the oil source options to date. In terrestrial manufacture, oil is ordinarily extracted with hexane, an organic solvent. However, exposed solvents are not permitted in the spacecraft environment or in enclosed human tests by National Aeronautics and Space Administration due to their potential danger and handling difficulty. As a result, alternative oil-processing methods will need to be utilized. Preparation and recovery options include traditional dehulling, crushing, conditioning, and flaking, extrusion, pressing, water extraction, and supercritical extraction. These processing options were evaluated on criteria appropriate to the Advanced Life Support System and BIO-Plex application including: product quality, product stability, waste production, risk, energy needs, labor requirements, utilization of nonrenewable resources, usefulness of by-products, and versatility and mass of equipment to determine the most appropriate ALS edible oil-processing operation.

Conversion of Isoprenoid Oil by Catalytic Cracking and Hydrocracking over Nanoporous Hybrid Catalysts

Directory of Open Access Journals (Sweden)

Toshiyuki Kimura

2012-01-01

Full Text Available In order to produce petroleum alternatives from biomass, a significant amount of research has been focused on oils from microalgae due to their origin, which would not affect food availability. Nanoporous hybrid catalysts composed of ns Al2O3 and zeolites have been proven to be very useful compared to traditional catalysts in hydrotreating (HT, hydrocracking (HC, and catalytic cracking (CC of large molecules. To evaluate the reaction scheme and products from model isoprenoid compounds of microalgae oil, nanoporous hybrid catalyst technologies (CC: ns Al2O3/H-USY and ns Al2O3/H-GaAlMFI; HC: [Ni-Mo/γ-Al2O3]/ns Al2O3/H-beta were studied. The major product from CC on ns Al2O3/H-USY was highly aromatic gasoline, while the product from HC was half-isoparaffinic/olefinic kerosene. Although more than 50 wt% of the products from HT/CC on the USY catalyst was liquefied petroleum gas due to overcracking, the product from HT/CC on the MFI catalyst was high-octane-number gasoline. Delightfully, the product from HT/HC was kerosene and its average number was 11, with more than 80 wt% being isoparaffinic. As a result, it was demonstrated that hydrotreating may convert isoprenoid oil from microalgae over nanoporous hybrid catalysts into a variety of products.

Effects of petroleum oil and soybean oil in adjuvants for postemergence herbicides

International Nuclear Information System (INIS)

Harrison, S.K.

1985-01-01

Soybean oil is an abundant and renewable resource through annual crop production. The replacement of paraffin oil with soybean oil in agricultural adjuvants would create an additional market for surplus soybeans and help alleviate dependence on non-renewable petroleum oil. Field and laboratory experiments were conducted to compare effects of a petroleum oil-emulsifier blend (POC) and a soybean oil-emulsifier blend (SBOC) as adjuvants for postemergence herbicides. In field experiments, little difference was observed between POC and SBOC in the ability to enhance control of velvetleaf (Abutilon theophrasti Medik.) with 0.6 or 1.1 kg/ha bentazon [3-(1-methylethyl)-(1H)-2,1,3-benzothiadiazin-4(3H)-one 2,2-dioxide]. Control of giant foxtail (Setaria faberi Herrm.) with 0.1 kg/ha sethoxydim {2-[1-(ethoxyimino)butyl]-5-[2-(ethylthio)propyl]-3-hydroxy-2-cyclohexen-1-one} was enhanced more by POC than by SBOC. The effects of adjuvants and relative humidity (RH) on absorption, translocation, and metabolism of the methyl ester of 14 C-haloxyfop {2-[4-[[3-chloro-5-(trifluoromethyl)-2-pyridinyl]oxy]phenoxy]propanoic acid} in corn (Zea mays L.) were investigated. Addition of 1.0% (v/v) POC to the treatment solution resulted in greater foliar absorption and translocation of 14 C than addition of 1.0% (v/v) SBOC

A Study on the Preparation of Regular Multiple Micro-Electrolysis Filler and the Application in Pretreatment of Oil Refinery Wastewater

Directory of Open Access Journals (Sweden)

Ruihong Yang

2016-04-01

Full Text Available Through a variety of material screening experiments, Al was selected as the added metal and constituted a multiple micro-electrolysis system of Fe/C/Al. The metal proportion of alloy-structured filler was also analyzed with the best Fe/C/Al ratio of 3:1:1. The regular Fe/C/Al multiple micro-electrolysis fillers were prepared using a high-temperature anaerobic roasting method. The optimum conditions for oil refinery wastewater treated by Fe/C/Al multiple micro-electrolysis were determined to be an initial pH value of 3, reaction time of 80 min, and 0.05 mol/L Na2SO4 additive concentration. The reaction mechanism of the treatment of oil refinery wastewater by Fe/C/Al micro-electrolysis was investigated. The process of the treatment of oil refinery wastewater with multiple micro-electrolysis conforms to the third-order reaction kinetics. The gas chromatography–mass spectrometry (GC–MS used to analyze the organic compounds of the oil refinery wastewater before and after treatment and the Ultraviolet–visible spectroscopy (UV–VIS absorption spectrum analyzed the degradation process of organic compounds in oil refinery wastewater. The treatment effect of Fe/C/Al multiple micro-electrolysis was examined in the continuous experiment under the optimum conditions, which showed high organic compound removal and stable treatment efficiency.

Recovery of oil from oil-in-water emulsion using biopolymers by adsorptive method.

Science.gov (United States)

Elanchezhiyan, S Sd; Sivasurian, N; Meenakshi, Sankaran

2014-09-01

In the present study, it is aimed to identify, a low cost sorbent for the recovery of oil from oil-in-water emulsion using biopolymers such as chitin and chitosan. Chitin has the greater adsorption capacity than chitosan due to its hydrophobic nature. The characterizations of chitin and chitosan were done using FTIR, SEM, EDAX, XRD, TGA and DSC techniques. Under batch equilibrium mode, a systematic study was performed to optimize the various equilibrium parameters viz., contact time, pH, dosage, initial concentration of oil, and temperature. The adsorption process reached equilibrium at 40 min of contact time and the percentage removal of oil was found to be higher (90%) in the acidic medium. The Freundlich and Langmuir models were applied to describe the equilibrium isotherms and the isotherm constants were calculated. Thermodynamic parameters such as ΔG°, ΔH° and ΔS° were calculated to find out the nature of the sorption mechanism. The kinetic studies were investigated with reaction-based and diffusion-based models. The suitable mechanism for the removal of oil has been established. Copyright © 2014 Elsevier B.V. All rights reserved.

The regional economic impact of oil and gas extraction in Texas

International Nuclear Information System (INIS)

Lee, Jim

2015-01-01

This paper empirically investigates the regional economic impact of oil and gas extraction in Texas during the recent shale oil boom. Regressions with county-level data over the period 2009–2014 support smaller multiplier effects on local employment and income than corresponding estimates drawn from popular input–output-based studies. Economic impacts were larger for extraction from gas wells than oil wells, while the drilling phase generated comparable impacts. Estimates of economic impacts are greater in a dynamic spatial panel model that allows for spillover effects across local economies as well as over time. - Highlights: • Economic impacts and multiplier effects differ between oil and gas wells in Texas. • Interactions among local economies raise employment and income effects. • Impacts persist over time, raising the long-run multipliers. • Greater economic impacts from newly drilled wells than legacy wells.

Catalytic Hydrodeoxygenation of Bio-oil Model Compounds over Pt/HY Catalyst

Science.gov (United States)

Lee, Heejin; Kim, Hannah; Yu, Mi Jin; Ko, Chang Hyun; Jeon, Jong-Ki; Jae, Jungho; Park, Sung Hoon; Jung, Sang-Chul; Park, Young-Kwon

2016-06-01

The hydrodeoxygenation of a model compound of lignin-derived bio-oil, guaiacol, which can be obtained from the pyrolysis of biomass to bio-oil, has attracted considerable research attention because of its huge potential as a substitute for conventional fuels. In this study, platinum-loaded HY zeolites (Pt/HY) with different Si/Al molar ratios were used as catalysts for the hydrodeoxygenation of guaiacol, anisole, veratrole, and phenol to a range of hydrocarbons, such as cyclohexane. The cyclohexane (major product) yield increased with increasing number of acid sites. To produce bio-oil with the maximum level of cyclohexane and alkylated cyclohexanes, which would be suitable as a substitute for conventional transportation fuels, the Si/Al molar ratio should be optimized to balance the Pt particle-induced hydrogenation with acid site-induced methyl group transfer. The fuel properties of real bio-oil derived from the fast pyrolysis of cork oak was improved using the Pt/HY catalyst.

Grinding temperature and energy ratio coe cient in MQL grinding of high-temperature nickel-base alloy by using di erent vegetable oils as base oil

Institute of Scientific and Technical Information of China (English)

Li Benkai; Li Changhe; Zhang Yanbin; Wang Yaogang; Jia Dongzhou; Yang Min

2016-01-01

Vegetable oil can be used as a base oil in minimal quantity of lubrication (MQL). This study compared the performances of MQL grinding by using castor oil, soybean oil, rapeseed oil, corn oil, sunflower oil, peanut oil, and palm oil as base oils. A K-P36 numerical-control precision surface grinder was used to perform plain grinding on a workpiece material with a high-temperature nickel base alloy. A YDM–III 99 three-dimensional dynamometer was used to measure grinding force, and a clip-type thermocouple was used to determine grinding temperature. The grinding force, grind-ing temperature, and energy ratio coefficient of MQL grinding were compared among the seven veg-etable oil types. Results revealed that (1) castor oil-based MQL grinding yields the lowest grinding force but exhibits the highest grinding temperature and energy ratio coefficient;(2) palm oil-based MQL grinding generates the second lowest grinding force but shows the lowest grinding temperature and energy ratio coefficient;(3) MQL grinding based on the five other vegetable oils produces similar grinding forces, grinding temperatures, and energy ratio coefficients, with values ranging between those of castor oil and palm oil;(4) viscosity significantly influences grinding force and grinding tem-perature to a greater extent than fatty acid varieties and contents in vegetable oils;(5) although more viscous vegetable oil exhibits greater lubrication and significantly lower grinding force than less vis-cous vegetable oil, high viscosity reduces the heat exchange capability of vegetable oil and thus yields a high grinding temperature;(6) saturated fatty acid is a more efficient lubricant than unsaturated fatty acid;and (7) a short carbon chain transfers heat more effectively than a long carbon chain. Palm oil is the optimum base oil of MQL grinding, and this base oil yields 26.98 N tangential grinding force, 87.10 N normal grinding force, 119.6 °C grinding temperature, and 42.7%energy ratio coefficient

Use of three generations of oil spill models during the Gulf War oil spills

International Nuclear Information System (INIS)

Cerkirge, H.M.; Al-Rabeh, A.H.; Gunay, N.

1992-01-01

During the January-May 1991 Gulf War, an estimated 6 million bbl of oil was spilled into the Arabian Gulf, mostly around Mina Al-Ahmadi in southern Kuwait. Three models were used to analyze the fate and transport of the spills originating at Al-Ahmadi. The first generation model, GULFSLIK I, was developed in the late 1970s and predicts the movements of a spill by considering that the center of the slick advects with a velocity equal to 3% of the wind speed. This model is best for the initial forecasting of oil spill movement. The second generation GULFSLIK II Model predicts the trajectory of spills at 24 h intervals, requiring as input the average daily wind velocity. Surface currents are obtained for the model from a reliable 3-dimensional hydrodynamic model of the Gulf coupled with an appropriate interpolation scheme. Comparisons between predicted spill trajectories and actual sightings show GULFSLIK II to be reasonably accurate. The third generation model, called OILPOL, consists of a set of algorithms describing the processes of advection, turbulent diffusion, surface spreading, vertical mechanical dispersion, emulsification, and evaporation. After 80 days, results show under 8% of the initial oil volume remains on the sea surface while 15% is suspended in the water column or sedimented on the sea bed. Comparisons of simulation results and actual sightings show excellent agreement. 4 refs., 7 figs., 2 tabs

Formulation of soy oil products

Directory of Open Access Journals (Sweden)

Woerfel, John B.

1995-12-01

Full Text Available The paper comments different formulations of soy oil products such as salad and cooking oils, margarine, shortenings, commercial shortenings, frying shortenings, and fluid shortenings. Hydrogenation and its influence on final products is also included.

El trabajo presenta diferentes formulaciones a base de aceite de soja tales como aceites para ensalada y cocinado, margarina, grasas sólidas (shortenings, grasas sólidas comerciales, grasas sólidas para frituras y grasas fluidas. Hace también referencia al proceso de hidrogenación y a sus efectos en los productos finales.

Investigation and development of heavy oil upgrading catalysts. 3

Energy Technology Data Exchange (ETDEWEB)

Lee, D.K.; Lee, I.C.; Yoon, W.L.; Lee, H.T.; Chung, H.; Hwang, Y.J.; Park, S.H. [Korea Inst. of Energy Research, Taejon (Korea, Republic of)

1995-12-01

This study aimed at the domestic development of HDS catalysts which are most fundamental and wide-used in the petroleum refinery. In this year, some experimental works were conducted for developing the effective utilization technology of the novel dispersed-catalysts in the hydro-desulfurization of heavy oils, and improving the reaction performance of alumina-supported Mo-based hydro-treating catalysts conventionally used in most of refineries. First, it was experimentally proved that the dispersed catalysts of Co-Mo could be employed for the hydro-desulfurization of a heavy atmospheric residual oil excluding the catalyst deactivation. The utilization of a carbon-expanded reactor in combination with this dispersed catalyst system exhibited an enhanced reaction performance and provided an efficient way for the separation and recovery of the dispersed catalytic component from oils. Second, the tungsten-incorporated WCoMo/{gamma}-Al{sub 2}O{sub 3} catalyst revealed the improved catalytic performance in the various hydro-treating reactions and in the initial deactivation rates for the high pressure hydro-treatment of a heavy oil as compared with the commercial CoMo/{gamma}-Al{sub 2}O{sub 3} catalyst. This new experimental finding for the promoting role of the monomeric WO{sub 3} species in CoMo/{gamma}-Al{sub 2}O{sub 3} catalyst may be generally applicable to the Mo-based alumina-sulfide phase, higher catalytic activity, and more extended service life. (author). 101 refs., 33 figs., 18 tabs.

ESTERIFICATION OF FATTY ACID FROM PALM OIL WASTE (SLUDGE OIL BY USING ALUM CATALYST

Directory of Open Access Journals (Sweden)

Thamrin Usman

2010-06-01

Full Text Available Esterification of fatty acids from palm oil waste (sludge oil as biodiesel liquid base has been done by using alum [Al2(SO43.14H2O] catalyst. Some reaction variables like reaction time, catalyst quantity, and molar ratio of sample-reactant was applied for optimal reaction. Yield of 94.66% was obtained at reaction condition 65 °C, 5 h, sample-reactant ratio 1:20, and catalyst quantity 3% (w/w. GC-MS analysis request showed that composition of methyl esters biodiesel are methyl caproic (0.67%, methyl lauric (0.21%, methyl miristic (1.96%, methyl palmitic (49.52%, methyl oleic (41.51%, and methyl stearic (6.13%. Physical properties of synthesized product (viscosity, refraction index and density are similar with those of commercial product.   Keywords: alum, biodiesel, esterification, sludge oil

An analysis of price and volatility transmission in butter, palm oil and crude oil markets

Directory of Open Access Journals (Sweden)

Dennis Bergmann

2016-11-01

Full Text Available Abstract Recent changes to the common agricultural policy (CAP saw a shift to greater market orientation for the EU dairy industry. Given this reorientation, the volatility of EU dairy commodity prices has sharply increased, creating the need to develop proper risk management tools to protect farmers’ income and to ensure stable prices for processors and consumers. In addition, there is a perceived threat that these commodities may be replaced by cheaper substitutes, such as palm oil, as dairy commodity prices become more volatile. Global production of palm oil almost doubled over the last decade while butter production remained relatively flat. Palm oil also serves as a feedstock for biodiesel production, thus establishing a new link between agricultural commodities and crude oil. Price and volatility transmission effects between EU and World butter prices, as well as between butter, palm oil and crude oil prices, before and after the Luxembourg agreement, are analysed. Vector autoregression (VAR models are applied to capture price transmission effects between these markets. These are combined with a multivariate GARCH model to account for potential volatility transmission. Results indicate strong price and volatility transmission effects between EU and World butter prices. EU butter shocks further spillover to palm oil volatility. In addition, there is evidence that oil prices spillover to World butter prices and World butter volatility.

Oil-in-Ice Demonstration 4: Quick Look Report

Science.gov (United States)

2016-11-01

A-3  Figure A-4. Temporary storage tank setup on the deck of USCGC Elm , December 2014 (ELASTEC American Marine 2014...an oil surrogate.  Boot covers work well for slippery surfaces, better than rubber boots. Oil-in-Ice IV Demonstration Quick Look Report 24...RDC | A. Balsley, et al. Public | November 2016 Figure A-4. Temporary storage tank setup on the deck of USCGC Elm , December 2014 (ELASTEC

2D seismic interpretation and characterization of the Hauterivian-Early Barremian source rock in Al Baraka oil field, Komombo Basin, Upper Egypt

Science.gov (United States)

Ali, Moamen; Darwish, M.; Essa, Mahmoud A.; Abdelhady, A.

2018-03-01

Komombo Basin is located in Upper Egypt about 570 km southeast of Cairo; it is an asymmetrical half graben and the first oil producing basin in Upper Egypt. The Six Hills Formation is of Early Cretaceous age and subdivided into seven members from base to top (A-G); meanwhile the B member is of Hauterivian-Early Barremian and it is the only source rock of Komombo Basin. Therefore, a detailed study of the SR should be carried out, which includes the determination of the main structural elements, thickness, facies distribution and characterization of the B member SR which has not been conducted previously in the study area. Twenty 2D seismic lines were interpreted with three vertical seismic profiles (VSP) to construct the depth structure-tectonic map on the top of the B member and to highlight the major structural elements. The interpretation of depth structure contour map shows two main fault trends directed towards the NW-SE and NE to ENE directions. The NW-SE trend is the dominant one, creating a major half-graben system. Also the depth values range from -8400 ft at the depocenter in the eastern part to -4800 ft at the shoulder of the basin in the northwestern part of the study area. Meanwhile the Isopach contour map of the B member shows a variable thickness ranging between 300 ft to 750 ft. The facies model shows that the B member SR is composed mainly of shale with some sandstone streaks. The B member rock samples were collected from Al Baraka-1 and Al Baraka SE-1 in the eastern part of Komombo Basin. The results indicate that the organic matter content (TOC) has mainly good to very good (1-3.36 wt %), The B member samples have HI values in the range 157-365 (mg HC/g TOC) and dominated by Type II/III kerogen, and is thus considered to be oil-gas prone based on Rock-Eval pyrolysis, Tmax values between 442° and 456° C therefore interpreted to be mature for hydrocarbon generation. Based on the measured vitrinite equivalent reflectance values, the B member SR

Detection of Oil in Water Column: Sensor Design

Science.gov (United States)

2013-02-01

droplets, because such particles produce spherical lensing effects characterized by distinct and unique constructive and deconstructive interference...increased surface area to volume ratio allowed naturally occurring bacteria greater access to the oil molecules so that they could be degraded. As with...are those that are nearly spherical, namely bubbles and oil droplets, because such particles produce spherical lensing effects characterized by

Upgrading of raw tall oil soap into fuel oils and lubricants; Raakasuovan jalostus poltto- ja voiteluoeljyksi

Energy Technology Data Exchange (ETDEWEB)

Oasmaa, A; Arpiainen, V; McKeough, P; Tapola, E; Haekkinen, R; Kuoppala, E; Koskela, K [VTT Energy, Jyvaeskylae (Finland). Energy Production Technologies

1997-12-01

Thermochemical processing of tall oil soap originating from various mixtures of birch and pine has been experimentally investigated. The organic matter of tall oil soap, which is a by- product of Kraft pulping, originates mainly from wood extractives. Conventional processing of tall oil soap involves acidulation with sulphuric acid to yield crude tall oil and subsequent distillation of the oil at centralised refineries. Because tall oil originating from birch wood is far less valuable than that from pine, there is an economic incentive in the Nordic countries to develop alternative conversion processes for the tall oil soap produced at pulp mills where birch is widely used as feedstock. Furthermore, thermochemical processing of tall oil soap does not introduce sulphur into the chemical recovery cycle. This would be a significant advantage in future mills employing closure of water circuits and/or sulphur-free pulping. In small-scale experiments tall oil soaps from wood mixtures with high birch content have been processed using both liquid-phase thermal treatment and pyrolysis. The liquid-phase thermal treatment at 450 deg C under a nitrogen atmosphere yielded a good-quality oil product at high yield (about 50 % of the energy content of the tall oil soap). In the atmospheric pyrolysis of birch tall oil soap a separation of inorganic and organic constituents was obtained. The energy value of the product gases was high. Both processes are promising, but the pyrolysis alternative has the greater economic potential, providing that the promising preliminary experimental results have given a true picture of the performance of the full-scale pyrolysis process. (orig.)

Uppgrading of raw tall oil soap into fuel oils and lubricants; Raakasuovan jalostus poltto- ja voiteluoeljyksi

Energy Technology Data Exchange (ETDEWEB)

Oasmaa, A.; Arpiainen, V.; McKeough, P.; Tapola, E. [VTT Energy, Espoo (Finland)

1998-12-31

Thermochemical processing of tall oil soap originating from various mixtures of birch and pine has been experimentally investigated. The organic matter of tall oil soap, which is a by-product of kraft pulping, originates mainly from wood extractives. Conventional processing of tall oil soap involves acidulation with sulphuric acid to yield crude tall oil and subsequent distillation of the oil at centralised refineries. Because tall oil originating from birch wood is far less valuable than that from pine, there is an economic incentive in the Nordic countries to develop alternative conversion processes for the tall oil soap produced at pulp mills where birch is widely used as feedstock. Furthermore, thermochemical processing of tall oil soap does not introduce sulphur into the chemical recovery cycle. This would be a significant advantage in future mills employing closure of water circuits and/or sulphur-free pulping. In small-scale experiments tall oil soaps from wood mixtures with high birch content have been processed using both liquid-phase thermal treatment and pyrolysis. The liquid-phase thermal treatment at 450 deg C under a nitrogen atmosphere yielded a good-quality oil product at high yield (about 50% of the energy content of the tall oil soap). In the atmospheric pyrolysis of birch tall oil soap a separation of inorganic and organic constituents was obtained. The energy value of the product gases was high. Both processes are promising, but the pyrolysis alternative has the greater economic potential, providing that the promising preliminary experimental results have given a true picture of the performance of the full-scale pyrolysis process. (orig.)

Fuel properties of biodiesel produced from the crude fish oil from the soapstock of marine fish

Energy Technology Data Exchange (ETDEWEB)

Lin, Cherng-Yuan; Li, Rong-Ji [Department of Marine Engineering, National Taiwan Ocean, University, Keelung 20224 (China)

2009-01-15

The soapstock of a mixture of marine fish was used as the raw material to produce the biodiesel in this study. The soapstock was collected from discarded fish products. Crude fish oil was squeezed from the soapstock of the fish and refined by a series of processes. The refined fish oil was transesterified to produce biodiesel. The fuel properties of the biodiesel were analyzed. The experimental results showed that oleic acid (C18:1) and palmitic acid (C16:0) were the two major components of the marine fish-oil biodiesel. The biodiesel from the mixed marine fish oil contained a significantly greater amount of polyunsaturated fatty acids than did the biodiesel from waste cooking oil. In addition, the marine fish-oil biodiesel contained as high as 37.07 wt.% saturated fatty acids and 37.3 wt.% long chain fatty acids in the range between C20 and C22. Moreover, the marine fish-oil biodiesel appeared to have a larger acid number, a greater increase in the rate of peroxidization with the increase in the time that it was stored, greater kinematic viscosity, higher heating value, higher cetane index, more carbon residue, and a lower peroxide value, flash point, and distillation temperature than those of waste cooking-oil biodiesel. (author)

Biosurfactants and their role in oil recovery

Energy Technology Data Exchange (ETDEWEB)

McInerney, Michael J. [University of Oklahoma (United States)

2011-07-01

This paper presents the role of biosurfactants in oil recovery. Types of biosurfactants include, among others, lipopeptides, rhamnolipids, sophorolipids. The process of oil recovery and the involvement of microbes are explained. The objective is to know if lipopeptide biosurfactants lower interfacial tension. Fatty acid composition is important for lipopeptide biosurfactant activity and microbial surfactants are hydrophilic and Interfacial Tension (IFT) values are high. Examples of biosurfactants with lower IFT values with mixtures are also given. An experiment was conducted to determine whether lipopeptides recovery entrapped oil or not. The procedure and experimental setup are shown. It is seen that with higher concentration of biosurfactants, the percentage of residual oil recovery is higher. Another experiment was conducted to see if biosurfactants greater than 40 mg/l can be produced in oil reservoirs. The experimental design and the analysis with the results are given. It was seen that more oil was produced. Conclusions from the study were, among other findings, that, in situ biosurfactant production and inoculation are possible.

Effects of Nanoparticle Materials on Prebreakdown and Breakdown Properties of Transformer Oil

Directory of Open Access Journals (Sweden)

Yuzhen Lv

2018-04-01

Full Text Available In order to reveal the effects of nanoparticle materials on prebreakdown and breakdown properties of transformer oil, three types of nanoparticle materials, including conductive Fe3O4, semiconductive TiO2 and insulating Al2O3 nanoparticles, were prepared with the same size and surface modification. An experimental study on the breakdown strength and prebreakdown streamer propagation characteristics were investigated for transformer oil and three types of nanofluids under positive lightning impulse voltage. The results indicate that the type of nanoparticle materials has a notable impact on breakdown strength and streamer propagation characteristics of transformer oil. Breakdown voltages of nanofluids are markedly increased by 41.3% and 29.8% respectively by the presence of Fe3O4 and TiO2 nanoparticles. Whereas a slight increase of only 7.4% is observed for Al2O3 nanofluid. Moreover, main discharge channels with thicker and denser branches are formed and the streamer propagation velocities are greatly lowered both in Fe3O4 and TiO2 nanofluids, while no obvious change appears in the propagation process of streamers in Al2O3 nanofluid in comparison with that in pure oil. The test results of trap characteristics reveal that the densities of shallow traps both in Fe3O4 and TiO2 nanofluids are much higher than that in Al2O3 nanofluid and pure oil, greatly reducing the distortion of the electric field. Thus, the propagations of positive streamers in the nanofluids are significantly suppressed by Fe3O4 and TiO2 nanoparticles, leading to the improvements of breakdown strength.

Evaluation of alkaline dissolution of Al 6061 and Al 1050 for the production of Mo-99 from LEU targets

International Nuclear Information System (INIS)

Mindrisz, Ana C.; Camilo, Ruth L.; Araujo, Izilda C.; Forbicini, Christina A.L.G. de O.

2013-01-01

Since 2008, due to the global crisis in the production of radioisotope 99 Mo, which product of decay, 99m Tc, is the tracer element most often used in nuclear medicine and accounts for about 80% of all diagnostic procedures in vivo. Studies on the alkaline dissolution to obtain 9 9M o from irradiated UAl x -Al LEU targets are under development. Processing time should be minimized, considering the short half-life of 99 Mo and 99m Tc, about 66 h and 6 h, respectively. This makes dissolution time a significant factor in the development of the process. This paper presents the results of alkaline dissolution of 'scraps' of Al 6061 and 1050, used to simulate the dissolution process of UAl x -Al targets. Dissolution time and gas releasing were evaluated using the following alkaline solutions: a) NaOH 3 mol.L -1 and NaNO 3 2 mol.L -1 , b) NaOH 3 mol.L -1 and NaNO 3 4 mol.L -1 . The initial temperature of dissolution was 85 deg C in all cases. Al 6061 showed values of dissolution time greater than that for Al 1050, 25% for NaNO 3 2 mol.L -1 and 104.55% for NaNO 3 4 mol.L -1 . The dissolution with NaNO 3 2 mol.L -1 showed that the gas releasing for Al 6061 was 2.7% greater than for Al 1050. However Al 1050 showed that gas releasing 9.92% greater than for Al 6061 during the dissolution with NaNO 3 4 mol.L -1 . The decision about what type of alloy has to be used, Al 1050 or Al 6061, it will be upto the group that will manufacture the targets for the RMB. (author)

The Proceedings of the Conference on Assessment of Ecological Impacts of Oil Spills Held 14-17 Jun 1978, Keystone, Colorado.

Science.gov (United States)

1978-01-01

damage may find that he cannot recover his damage prevention costs , though he could have recovered his costs of hauling an oil soiled boat after the...SEA Otto Gra hi—Nielsen Institute of Marine Research Box 1870 N- Soil Bergen , Norway...oil applied externally to the eggshell . surface (Al bers 1977; Szaro and Albers 1977; Szaro et al. 1978) . Therefore small amounts of oil transferred

Urea-nitrate combustion synthesis of MgO/MgAl2O4 nanocatalyst used in biodiesel production from sunflower oil: Influence of fuel ratio on catalytic properties and performance

International Nuclear Information System (INIS)

Rahmani Vahid, Behgam; Haghighi, Mohammad

2016-01-01

Graphical abstract: As a base catalyst for biodiesel production, MgAl 2 O 4 spinel was successfully synthesized by combustion method with MgO, as the active phase, dispersed on the catalyst surface. The nanocatalysts were characterized by XRD, FESEM, EDX, BET-BJH, TGA and FTIR analyses, so as to optimize the concentration of urea (as fuel) in the combustion synthesis. Analyzing the effect of fuel ratio on the combustion synthesized MgAl 2 O 4 , it was revealed that the synthesized base catalyst with a fuel ratio of 1.5 was of the best specifications for biodiesel production process. Future researches may investigate the catalyst reusability and mild reaction conditions, so as to achieve more economical production of biodiesel. - Highlights: • Efficient synthesis of MgAl 2 O 4 spinel by solution combustion method. • Improvement of catalytic activity and stability by optimum ratio fuel. • Enhanced dispersion of MgO over MgAl 2 O 4 spinel. • Production of biodiesel over MgO/MgAl 2 O 4 at relatively mild reaction conditions. - Abstract: MgO/MgAl 2 O 4 nanocatalyst was synthesized by a simple, cost-effective and rapid method and used in biodiesel production from sunflower oil. MgAl 2 O 4 was synthesized by combustion method at different fuel ratios and then active phase of MgO was dispersed on the samples by impregnation method. The nanocatalysts were characterized by XRD, FESEM, EDX, BET-BJH, TGA and FTIR analyses, so as to optimize the concentration of urea (as fuel) in the combustion synthesis. The physicochemical properties of the nanocatalyst confirmed the sample synthesized with fuel ratio of 1.5 has high surface area, effective morphology and texture properties. Finally, in order to evaluate catalytic activity of the samples in biodiesel production, the transesterification reaction was performed. The results indicated the catalyst prepared by combustion synthesis with a fuel ratio of 1.5 was optimum specifications for biodiesel production. Using this

Pembuatan Katalis Asam (Ni/γ-Al2O3 dan Katalis Basa (Mg/γ-Al2O3 untuk Aplikasi Pembuatan Biodiesel dari Bahan Baku Minyak Jelantah

Directory of Open Access Journals (Sweden)

. Savitri

2016-05-01

Full Text Available Biodiesel is an alternative energy fuel a substitute for diesel oil produced from vegetable oil or animal fat which have the advantage easily used, they are biodegradable, not toxic and sulfur free. This research aims to do process of prosucing biodiesel using acid catalysts (Ni/γ-Al2O3 for a esterification process and base catalyst (Mg/γ-Al2O3 for transesterification  process with the variation of catalyst concentration Ni/γ-Al2O3 (0.5%; 0.75%; 1% and 2% and the time (60 minutes, 120 minutes, and 180 minutes. Research of methodology starting to the process impregnation Ni and Mg metal into a buffer γ-Al2O3, characterization a catalyst with XRD, FTIR, and the SAA, and the esterification process to lower levels of FFA and transesterification process for making it biodiesel. The characterization with X-RD does not appear a new peak, only just occurred a shift peak, and declines intensity of Ni/γ-Al2O3 and Mg/γ-Al2O3. The analysis result of the SAA, a decline in the surface area (the decline in active side of catalyst suspected the process impregnation not run perfect because Ni and Mg metal only distributed on the surface of buffer pore. The results of the FTIR analysis does not occur the addition of acidity and alkalinity. The steady of catalyst concentration from esterification process is 1% within 120 minutes produce levels of FFA 6.85%.  Keywords: Biodiesel, esterification, impregnation, used cooking oil, transesterificationDOI : http://dx.doi.org/10.15408/jkv.v2i1.3104

Enhancement of oleic acid in butter oil by high oleic fraction of moringa oleifera oil

International Nuclear Information System (INIS)

Nadeem, M.; Ullah, R.

2016-01-01

Oleic acid in butter oil (BO) was enhanced by a high oleic acid fraction (HOF) of Moringa oleifera oil (MOO). HOF was blended with BO at four different concentrations i.e. 5%, 10 percent, 15% and 20% (HOF-5, HOF-10, HOF-15 and HOF-20, respectively), compared with a control (BO). The oleic acid in HOF increased from 71.55 percent to 80.25%. DPPH free radical scavenging activity and total flavonoid content of HOF was 76.88% and 34.52 mg/100 g. Supplementation of butter oil with 20% HOF, decreased the cholesterol from 224 to 177 mg/100 g. Peroxide value of three months stored HOF-20 was 1.18 (meqO/sub 2/ kg) as compared to control, 3.15 (meqO/sub 2/kg). Induction period of HOF-20 was 4.07 h greater than control. These results evidenced that oleic acid in butter oil can be substantially increased by HOF of MOO. (author)

Biodegradation waste of the stations service by Rhodococcus erythropolis ohp-al-gp

International Nuclear Information System (INIS)

Pucci, Oscar Hector; Acuna, Adrian Javier; Pucci, Graciela Natalia

2013-01-01

The strain Rhodococcus erythropolis ohp-al-gp was isolated from turbine oil contaminated soil from northern Santa Cruz province, Argentina. Because of its potential in bioremediation, the aim was to know the abilities for degradation of pure compounds and mixtures of hydrocarbons, as well as degradation in the presence and absence of diesel nitrogen measured by gas chromatography. The strain possesses the ability to use diesel, kerosene, lubricating oil, pristane, hexane, heptane, octane, pentadecane and hexadecane. R. erythropolis ohp-al-gp has excellent potential for bioremediation of hydrocarbons, which are conflictive as lubricating oils, their potential use in removing mud from washing engines or gas stations would be its most important application. The degradation rate in optimal culture conditions, gives it an additional advantage. It also has a low degradation in the absence of nitrogen, a frequent limiting factor in Patagonian soils.

Influence of a big oil spill during the Gulf War on intertidal invertebrates

International Nuclear Information System (INIS)

Kado, Ryusuke; Tokuda, Hiroshi; Satoh, Hiroo; Hanawa, Shinichi; Murata, Yukiwo

1993-01-01

It is well known that a massive oil spill washed ashore from Al Khafji to the west side of the Abu Ali Peninsula in the western Arabian Gulf during the Gulf War. In these areas enormous amounts of oil are still left along most beaches at the high tide level. Surveys were carried out to clarify the effects of the massive oil spill

Economic Viability of the Use of Local Pseudo-Oils for Drilling Fluid ...

African Journals Online (AJOL)

Michael O. Mensah

2015-12-02

Dec 2, 2015 ... Applications” Journal of Petroleum and Gas. Engineering, Vol. 6(4) ... productive, onshore horizontal wells in India. (Sawyer et al. ... fewer effects on benthic communities than the early generation oil ... Home-Cooking Oil (XB1000). Drilling fluids ..... mining and microbial mineral recovery and environmental.

Study of jojoba oil aging by FTIR.

Science.gov (United States)

Le Dréau, Y; Dupuy, N; Gaydou, V; Joachim, J; Kister, J

2009-05-29

As the jojoba oil was used in cosmetic, pharmaceutical, dietetic food, animal feeding, lubrication, polishing and bio-diesel fields, it was important to study its aging at high temperature by oxidative process. In this work a FT-MIR methodology was developed for monitoring accelerate oxidative degradation of jojoba oils. Principal component analysis (PCA) was used to differentiate various samples according to their origin and obtaining process, and to differentiate oxidative conditions applied on oils. Two spectroscopic indices were calculated to report simply the oxidation phenomenon. Results were confirmed and deepened by multivariate curve resolution-alternative least square method (MCR-ALS). It allowed identifying chemical species produced or degraded during the thermal treatment according to a SIMPLISMA pretreatment.

Evaluation Study Of Inhibition And Regeneration Characters For Substituted Anilines Extracted From Crude Oil

Directory of Open Access Journals (Sweden)

Dr. Mohammad Jamil Abd-Alghani

2015-08-01

Full Text Available Abstract Aniline derivatives containing carbonyl group in the side chain was extracted from crude oil received from Al- Dora refinery. The crude oil was dissolved in xylene 13 and extracted through a column containing activated cationic resin type Amberlyte 15 then eluted by absolute ethanol and identified by infra red spectroscopy then examined as antioxidant for lubricant oil stock 50. FT-IR spectroscopy for the lubricant oil was performed before employing in an internal combustion engine and 190 hrs after. It was seen that the FT-IR of the oxidized oil contains a new peak in the region 1700 1800 cm1 which is formed due to the oxidation of base oil which belongs to carbonyl group. The FT-IR specter for the formulated crude oil with a specific concentration of the extracted substituted aniline after applying the same conditions of oxidation 190 working hrs. in an internal combustion engine showed a minimum peak intensity at 1710 1770 cm-1 than that observed in FT-IR done in absence of extracted antioxidant. The values of induction periods in presence of 0.20 and 0.30 moll of the extracted sample in the lubricant oil at 393 K were 766 sec. 1630 sec. while in their absence was 55 sec.. The values of maximum rates of oxidation were 3.0x10-4 and 2.0x10-4 moll. sec. These values were still not arrived the value of maximum rate of oxidation for the lubricant oil 3.5 x10-4 mol.l.sec. The same study was applied on the universal antioxidant inhibitor 2 6-diter-butyl-4-methyl phenol phenolic type under the same conditions. The obtained induction periods were 150 290 sec. respectively. This means that the values of induction periods obtained by formulating the lubricant oil with the extracted aniline molecule were 7 times greater than do the 2 6- diter-butyl-4-methyl phenol molecule. From the literatures it is known that the value of stochiometric factor for inhibition f for 2 4 6-triisobutyl phenol is equal to 2 so as a result the value of stochiometric

Comparison of product selectivity during hydroprocessing of bitumen derived gas oil in the presence of NiMo/Al{sub 2}O{sub 3} catalyst containing boron and phosphorus

Energy Technology Data Exchange (ETDEWEB)

D. Ferdous; A.K. Dalai; J. Adjaye [University of Saskatchewan, SK (Canada). Catalysis and Chemical Reactor Engineering Laboratories, Department of Chemical Engineering

2006-06-15

A detailed experimental study was performed in a trickle-bed reactor using bitumen derived gas oil. The objective of this work was to compare the activity of NiMo/Al{sub 2}O{sub 3} catalyst containing boron or phosphorus for the hydrotreating and mild hydrocracking of bitumen derived gas oil. Experiments were performed at the temperature and LHSV of 340-420{sup o}C and 0.5-2 h{sup -1}, respectively, using NiMo/Al{sub 2}O{sub 3} catalysts containing 1.7 wt% boron or 2.7 wt% phosphorus. In the temperature range of 340-390{sup o}C, higher nitrogen conversion was observed from boron containing catalyst than that from phosphorus containing catalyst whereas in the same temperature range, phosphorus containing catalyst gave higher relative removal of sulfur than boron containing catalyst. Phosphorus containing catalyst showed excellent hydrocracking and mild hydrocracking activities at all operating conditions. Higher naphtha yield and selectivity were obtained using phosphorus containing catalyst at all operating conditions. Maximum gasoline selectivity of {approximately}45 wt% was obtained at the temperature, pressure, and LHSV of 400{sup o}C, 9.4 MPa and 0.5 h{sup -1}, respectively, using catalyst containing 2.7 wt% phosphorus. 40 refs., 13 figs., 1 tab.

Positive and Negative Impacts of Oil Palm Expansion in Indonesia and the Prospect to Achieve Sustainable Palm Oil

Science.gov (United States)

Shahputra, M. A.; Zen, Z.

2018-02-01

The aim of the study is to deepen understanding the role of palm oil on Indonesian economy, poverty elevation and to investigate the positive and negative impacts of oil palm expansion, due to the burden of GHG emissions; and prospect to be more sustainable palm oil industry. The statistics show that average rural poverty tends to be lower and Gross Regional Product tends to be higher in provinces which have greater levels of oil palm cultivation. Indonesian oil palm will grow from 10.6 in 2013 to 13.7 million ha by 2020. This will release 135.59 million tons of CO2 if nothing is done to mitigate BAU emissions. Unless there are sustained efforts to redirect development and expansion of oil palm, plantation growth will continue to encroach on intact forest and peat land.. In fact Indonesia has large areas of degraded land, an estimated total 19,144,000 ha is available for planting oil palm and other crops. A large-scale expansion program driven by estate companies needs to be accompanied by effective smallholder development program in order to achieve the best outcome for local farmers and avoid the conflicts.

Production of biodiesel fuel by transesterification of different vegetable oils with methanol using Al₂O₃ modified MgZnO catalyst.

Science.gov (United States)

Olutoye, M A; Hameed, B H

2013-03-01

An active heterogeneous Al2O3 modified MgZnO (MgZnAlO) catalyst was prepared and the catalytic activity was investigated for the transesterification of different vegetable oils (refined palm oil, waste cooking palm oil, palm kernel oil and coconut oil) with methanol to produce biodiesel. The catalyst was characterized by using X-ray diffraction, Fourier transform infrared spectra, thermo gravimetric and differential thermal analysis to ascertain its versatility. Effects of important reaction parameters such as methanol to oil molar ratio, catalyst dosage, reaction temperature and reaction time on oil conversion were examined. Within the range of studied variability, the suitable transesterification conditions (methanol/oil ratio 16:1, catalyst loading 3.32 wt.%, reaction time 6h, temperature 182°C), the oil conversion of 98% could be achieved with reference to coconut oil in a single stage. The catalyst can be easily recovered and reused for five cycles without significant deactivation. Copyright © 2013 Elsevier Ltd. All rights reserved.

Lifetimes of Multiply Alkylated Cyclopentane Oil in Contact with Various Metals, Evaluated with Vacuum Spiral Orbit Tribometer

Science.gov (United States)

Pepper, Stephen V.

2018-01-01

The dependence of the lifetimes of small quantities of a Multiply Alkylated Cyclopentane (MAC) lubricant oil, Pennzane (Registered Trademark) 2001A (Nye Lubricants, Inc.), in rolling and sliding contact with different metals was evaluated with a vacuum spiral orbit tribometer. The metals were the bearing alloys 52100 steel, 440C steel, 17-4 PH steel and Nitinol 60 and the elements chromium, vanadium and titanium. The lifetimes of the lubricant oil on different metals fell into distinct groups with 52100 greater than 440C approx. Nitinol 60 greater than 17-4 PH for the order of the lifetimes of the steels and chromium greater than vanadium greater than titanium for the order of the lifetimes for the elements. The limited life of the small quantities of oil is assumed to be due to its consumption by the tribochemical reaction of the oil with the different metal bearing materials. The lifetimes are then inversely related to the reaction rates of the oil molecules with the various metals: the longest life of 52100 steel having the lowest reaction rate and the shortest life of titanium having the highest reaction rate. Mechanisms for the tribochemical reactions are discussed.

Evaluation of Crude Oil Biodegradation Efficiency and Peroxidase ...

African Journals Online (AJOL)

ADOWIE PERE

Increase in biomass enhanced degradation efficiency above 80 % after 10 days for all concentration of crude oil studied. Peroxidase ... compounds by various bacteria and fungi (Gianfreda et al, 1999) ... into a clean plastic container. Microbial.

Mineral oil; Mineraloel

Energy Technology Data Exchange (ETDEWEB)

Schult-Bornemann, Karl-Heinz [Magdeburg Univ. (Germany)

2015-07-01

The dominant theme in the world energy market was the fall in oil prices in 2014. From 115 US-$/bbl in June it dropped to below 50 US-$/bbl in January 2015. Thereby the shale oil revolution has had the strong impact on the global energy situation, to this point has been predicted for three years. Although no one could predict the exact height of the fall in oil prices, but with oil as a reserve currency for all other fuels, it has not only had an impact on the gas and coal prices, but other commodities, such as copper, have also yielded. About cause and effect, there is a lot of speculation - not all of which are supported by wisdom. [German] Das beherrschende Thema im Weltenergiemarkt war der Absturz des Rohoelpreises in 2014. Von 115 US-$/bbl im Juni sank er auf unter 50 US-$/bbl im Januar 2015. Damit hat die Schieferoelrevolution den kraeftigen Einfluss auf die Weltenergiesituation gehabt, der an dieser Stelle seit drei Jahren vorhergesagt wurde. Zwar konnte niemand die exakte Hoehe des Rueckgangs des Oelpreises prognostizieren, aber mit Oel als Leitwaehrung fuer alle anderen Energietraeger hat es nicht nur Einfluss auf den Gas- und Kohlepreis gehabt, sondern andere Rohstoffe, wie zum Beispiel Kupfer, haben ebenfalls nachgegeben. Ueber Ursache und Wirkung gibt es viele Spekulationen - nicht alle sind von Weisheit getragen.

Oil prices, nuclear energy consumption, and economic growth: New evidence using a heterogeneous panel analysis

International Nuclear Information System (INIS)

Lee, Chien-Chiang; Chiu, Yi-Bin

2011-01-01

This paper applies panel data analysis to examine the short-run dynamics and long-run equilibrium relationships among nuclear energy consumption, oil prices, oil consumption, and economic growth for developed countries covering the period 1971-2006. The panel cointegration results show that in the long run, oil prices have a positive impact on nuclear energy consumption, suggesting the existence of the substitution relationship between nuclear energy and oil. The long-run elasticity of nuclear energy with respect to real income is approximately 0.89, and real income has a greater impact on nuclear energy than do oil prices in the long run. Furthermore, the panel causality results find evidence of unidirectional causality running from oil prices and economic growth to nuclear energy consumption in the long run, while there is no causality between nuclear energy consumption and economic growth in the short run. - Research highlights: → We examine the relationship among nuclear energy consumption, oil prices, oil consumption, and economic growth for developed countries. → The existence of the substitution relationship between nuclear energy and oil. → Real income has a greater impact on nuclear energy than do oil prices in the long run. → An unidirectional causality running from oil prices and economic growth to nuclear energy consumption in the long run.

Examination of marine and vegetable oil oxidation data from a multi-year, third-party database.

Science.gov (United States)

De Boer, Anna A; Ismail, Adam; Marshall, Keri; Bannenberg, Gerard; Yan, Kevin L; Rowe, William J

2018-07-15

Fish oil (FO) products constitute good sources of omega-3 fats. Oxidation data from a large third-party database of 1900 + globally-sourced FO samples were assessed. In FO products, for peroxide value (PV), 13.9% exceeded 5 mEq O 2 /kg (2.2% >10); for acid value (AcV) 2.1% exceeded 3 mg KOH/g, while for p-anisidine value (pAV) in unflavoured oils, 6.1% exceeded 20, (3.8% >30), and 8.8% exceeded TOTOX limits (26). Additionally, we compared FO with other dietary oils. The FO median PV was similar to those of algal and sunflower oils, 4.8-fold greater than krill oil, and 5.2-fold less than extra-virgin olive oil. The median pAV differed non-significantly among oils. The FO median AcV was similar to those of algal and extra-virgin olive oils, 3.4-fold greater than sunflower oil, and 11.9-fold less than krill oil. This study has provided new insight that retail FO products predominantly meet regulatory guidelines and are comparable in oxidative status to other dietary oils. Copyright © 2018 The Authors. Published by Elsevier Ltd.. All rights reserved.

Kinetic study of olive oil degradation monitored by fourier transform infrared spectrometry. Application to oil characterization.

Science.gov (United States)

Román Falcó, Iván P; Grané Teruel, Nuria; Prats Moya, Soledad; Martín Carratalá, M Luisa

2012-11-28

A new approach for the determination of kinetic parameters of the cis/trans isomerization during the oxidation process of 24 virgin olive oils belonging to 8 different varieties is presented. The accelerated process of degradation at 100 °C was monitored by recording the Fourier transform infrared spectra. The parameters obtained confirm pseudo-first-order kinetics for the degradation of cis and the appearance of trans double bonds. The kinetic approach affords the induction time and the rate coefficient; these parameters are related to the fatty acid profile of the fresh olive oils. The data obtained were used to compare the oil stability of the samples with the help of multivariate statistical techniques. Fatty acid allowed a classification of the samples in five groups, one of them constituted by the cultivars with higher stability. Meanwhile, the kinetic parameters showed greater ability for the characterization of olive oils, allowing the classification in seven groups.

Air-deployable oil spill sampling devices review phase 2 testing. Volume 1

International Nuclear Information System (INIS)

Hawke, L.; Dumouchel, A.; Fingas, M.; Brown, C.E.

2007-01-01

SAIC Canada tested air deployable oil sampling devices for the Emergencies Science and Technology Division of Environment Canada in order to determine the applicability and status of these devices. The 3 devices tested were: Canada's SABER (sampling autonomous buoy for evidence recovery), the United States' POPEIE (probe for oil pollution evidence in the environment); and, Sweden's SAR Floatation 2000. They were tested for buoyancy properties, drift behaviour and sampler sorbent pickup ratios. The SAR and SABER both had lesser draft and greater freeboard, while the POPEIE had much greater draft than freeboard. All 3 devices could be used for oil sample collection in that their drift characteristics would allow for the SABER and SAR devices to be placed upwind of the slick while the POPEIE device could be placed downwind of an oil spill. The sorbent testing revealed that Sefar sorbent and Spectra sorbent used in the 3 devices had negative pickup ratios for diesel but performance improved as oil viscosity increased. Both sorbents are inert and capable of collecting oil in sufficient volumes for consistent fingerprinting analysis. 10 refs., 8 tabs., 8 figs

DWH MC 252: Subsurface Oil Transport

Science.gov (United States)

Beegle-Krause, C. J.; Boyer, T.; Murray, D.

2010-12-01

Before reaching the ocean surface, the oil and gas released from the DWH MC 252 blowout at 1500 m moves as a buoyant plume until the trapping depth and plume transition point are reached (Zheng et al 2002). At the transition point, the oil droplets and bubbles move independently of each other, and rise at a rate related to their diameter. The oil density, droplet size distribution and currents primarily determine the distribution of the oil between: Large droplets that rise quickly and create a surface expression of the oil. Moderate size droplets that rise over the course of days, and so spread out quite differently than the surface oil, and commonly do not reach the surface in large enough quantities to create a surface sheen. These droplets separate in the currents, particularly in the strong current shear in upper 500 m currents. Very tiny droplets that rise very slowly, over the course or weeks to months, and may be removed by dissolution, biodegradation or marine snow before ever reaching the surface. Modeling and observations (Joint Analysis Group, 2010) confirm the presence of a deep layer of oil and gas between approximately 1100 and 1300 m over the release location and spreading out along the isopycnal surfaces. Later in the event, a small oxygen depression was a proxy for where oil and gas had been. The DWH MC252 well is located at intermediate depth in the Gulf of Mexico (GoM). The water mass is Antarctic Intermediate Water, which enters and exits the GoM through the Yucatan Straits. Surface influences, such as Loop Current Frontal Eddies (e.g. Berger et al 2000) can reach down to these depths, and alter the flow within De Soto Canyon. The water mass containing the deep layer of oil droplets changes depth within the GoM, but does not reach above a depth of about 900 m. There are no physical processes that could cause this deep layer of oil to reach the continental shelf or the Florida Straits. Observed and historical hydrographic data, observations

ALS-Plus Syndrome: Non-Pyramidal Features in a Large ALS Cohort

Science.gov (United States)

McCluskey, Leo; Vandriel, Shannon; Elman, Lauren; Van Deerlin, Vivianna M.; Powers, John; Boller, Ashley; Wood, Elisabeth McCarty; Woo, John; McMillan, Corey T.; Rascovsky, Katya; Grossman, Murray

2014-01-01

Objective Autopsy studies show widespread pathology in amyotrophic lateral sclerosis (ALS), but clinical surveys of multisystem disease in ALS are rare. We investigated ALS-Plus syndrome, an understudied group of patients with clinical features extending beyond pyramidal and neuromuscular systems with or without cognitive/behavioral deficits. Methods In a large, consecutively-ascertained cohort of 550 patients with ALS, we documented atypical clinical manifestations. Genetic screening for C9orf72 hexanucleotide expansions was performed in 343 patients, and SOD1, TARDBP, and VCP were tested in the subgroup of patients with a family history of ALS. Gray matter and white matter imaging was available in a subgroup of 30 patients. Results Seventy-five (13.6%) patients were identified with ALS-Plus syndrome. We found disorders of ocular motility, cerebellar, extrapyramidal and autonomic functioning. Relative to those without ALS-Plus, cognitive impairment (8.0% vs 2.9%, p=0.029), bulbar-onset (49.3% vs 23.2%, pALS-Plus. Survival was significantly shorter in ALS-Plus (29.66 months vs 42.50 months, p=0.02), regardless of bulbar-onset or mutation status. Imaging revealed significantly greater cerebellar and cerebral disease in ALS-Plus compared to those without ALS-Plus. Conclusions ALS-Plus syndrome is not uncommon, and the presence of these atypical features is consistent with neuropathological observations that ALS is a multisystem disorder. ALS-Plus syndrome is associated with increased risk for poor survival and the presence of a pathogenic mutation. PMID:25086858

Effect of methanol extracts of rosemary and olive vegetable water on the stability of olive oil and sunflower oil

Directory of Open Access Journals (Sweden)

Gamel, T. H.

1999-10-01

Full Text Available Effect of methanol extracts of rosemary and olive vegetable water on the stability of olive oil and sunflower oil. Methanol phenolic extracts of dry rosemary leaves and olive vegetable water filtrate, in combination with BHA, were added to olive oil (blend of refined and virgin olive oil, 3 to 1 and to sunflower oil and their antioxidant effects under accelerated conditions were evaluated. Accelerated conditions included the oven test (at 63 °C and the conductivity method (Rancimat at 120 °C. Frying process at 180 °C was also applied. The methanol phenolic extracts and the BHA were added to each oil at the following concentrations: 200 ppm rosemary extract; 200 ppm olive vegetable water extract; 100 ppm rosemary extract + 100 ppm BHA; 100 ppm vegetable water extract + 100 ppm BHA and 200 ppm BHA. In general, antioxidant effect of phenolic additives of rosemary and of BHA was in the following order: 200 ppm rosemary extract > 100 ppm rosemary extract + 100 ppm BHA > and 200 ppm BHA. The addition of 200 ppm vegetable water extract and 100 ppm vegetable water extract + 100 ppm BHA exhibited similar antioxidant effect to that of 200 ppm BHA.

Extractos metanólicos de fenoles de hojas secas de romero y filtrados de agua de vegetación de la aceituna, en combinación con BHA, se añadieron al aceite de oliva (mezcla de aceite de oliva refinado y virgen, 3 a 1 y al aceite de girasol, evaluándose sus efectos antioxidantes usando condiciones aceleradas. Estas condiciones incluyeron el test del horno de oxidación (a 63 °C y el método de conductividad (Rancimat a 120 °C. También se aplicó al proceso de fritura a 180 °C. Los extractos metanólicos de fenoles y el BHA se añadieron a cada aceite en las siguientes concentraciones: 200 ppm de extracto de romero, 200 ppm de extracto de agua de vegetación de la aceituna, 100 ppm de extracto de romero + 100 ppm de BHA, 100 ppm de extracto de agua de vegetación + 100 ppm de BHA y 200 ppm de BHA

Topology and stability of a water-soybean-oil swirling flow

Science.gov (United States)

Carrión, Luis; Herrada, Miguel A.; Shtern, Vladimir N.

2017-02-01

This paper reveals and explains the flow topology and instability hidden in an experimental study by Tsai et al. [Tsai et al., Phys. Rev. E 92, 031002(R) (2015)], 10.1103/PhysRevE.92.031002. Water and soybean oil fill a sealed vertical cylindrical container. The rotating top disk induces the meridional circulation and swirl of both fluids. The experiment shows a flattop interface shape and vortex breakdown in the oil flow developing as the rotation strength R eo increases. Our numerical study shows that vortex breakdown occurs in the water flow at R eo=300 and in the oil flow at R eo=941 . As R eo increases, the vortex breakdown cell occupies most of the water domain and approaches the interface at R eo around 600. The rest of the (countercirculating) water separates from the axis as the vortex breakdown cells in the oil and water meet at the interface-axis intersection. This topological transformation of water flow significantly contributes to the development of the flattop shape. It is also shown that the steady axisymmetric flow suffers from shear-layer instability, which emerges in the water domain at R eo=810 .

Conversion characteristics of 10 selected oil shales

Energy Technology Data Exchange (ETDEWEB)

Miknis, F.P.

1989-08-01

The conversion behavior of 10 oil shale from seven foreign and three domestic deposits has been studied by combining solid- and liquid-state nuclear magnetic resonance (NMR) measurements with material balance Fischer assay conversion data. The extent of aromatization of aliphatic carbons was determined. Between zero and 42% of the raw shale aliphatic carbon formed aromatic carbon during Fischer assay. For three of the shales, there was more aromatic carbon in the residue after Fisher assay than in the raw shale. Between 10 and 20% of the raw shale aliphatic carbons ended up as aliphatic carbons on the spent shale. Good correlations were found between the raw shale aliphatic carbon and carbon in the oil and between the raw shale aromatic carbon and aromatic carbon on the spent shale. Simulated distillations and molecular weight determinations were performed on the shale oils. Greater than 50% of the oil consisted of the atmospheric and vacuum gas oil boiling fractions. 14 refs., 15 figs., 1 tab.

Nutrient-enhanced bioremediation of oil-contaminated shoreline

International Nuclear Information System (INIS)

Glaser, J.A.

1991-01-01

On March 24, 1989, the collision of the supertanker Exxon Valdez with a submerged reef in Prince William Sound AK, released 41.6 million L (11 million gal) of Prudhoe Bay crude oil. The oil spread with time to contaminate an estimated 565 km (350 miles) of shoreline. The degradation of oil components by biological mechanisms has been intensively studied during the last 20 years. The general outline of biodegradation pathways for aliphatic and aromatic hydrocarbons has been formulated and continues to be developed in greater detail. Consequently, the microbial decomposition of oil in aquatic environments is well understood to include descriptions of biodegradation kinetics; temperature effects for biodegradation can be described by an Arrhenius relationship. Even cold-water environments have been shown to support the biodegradation of oil components. This paper reports that a panel of experts was assembled to assist the U.S. Environmental Protection Agency (EPA) in determining the best treatment strategy to accelerate the natural biodegradation process in Prince William Sound

Effects of supplementation with vegetable oils, including castor oil, on milk production of ewes and on growth of their lambs.

Science.gov (United States)

Parente, Michelle de Oliveira Maia; Susin, Ivanete; Nolli, Cristine Paduan; Ferreira, Evandro Maia; Gentil, Renato Shinkai; Polizel, Daniel Montanher; Pires, Alexandre Vaz; Alves, Susana Paula; Bessa, Rui José Branquinho

2018-02-15

The objectives in this experiment were to compare the effects of castor oil, canola oil, or sunflower oil on lactation performance, milk composition, and milk fatty acid (FA) profile in Santa Inês ewes and on growth of lambs. Forty-four ewes (66.9 ± 4.7 kg of initial BW, mean ± SD) were penned individually with their lambs and used in a randomized complete block design with 11 blocks and four diets. The experimental diets were as follows: 1) basal diet without added oil (control), 2) 30 g FA/kg DM of canola oil (CAN), 3) 30 g FA/kg DM of sunflower oil (SUN), and 4) 30 g FA/kg DM of castor oil (CAS). The oils were added to a basal diet containing 50% of roughage. Once a week, from the 2nd to 8th wk of lactation, ewes were separated from their lambs, injected with oxytocin, and mechanically milked to empty the udder. After 3 h, using the same procedure, milk production was recorded, and milk was sampled for composition and FA profile determination. The growth of the lambs was monitored weekly. Ewes fed the control diet had greater (P oil-supplemented diets. No effect was observed on milk yield and on final BW of lambs. Milk fat and milk total solid concentrations were greater (P oil-supplemented diets reduced (P < 0.05) the content of 16:0 when compared with the control. Milk from ewes fed CAS presented only small proportion of 12-OH,c9-18:1 (0.31% of total FA) but much larger proportions of 12-OH-18:0 (1.58% of total FA) and particularly of 12-oxo-18:0 (2.95 % of total FA), which suggests that 12-OH,c9-18:1 was extensively metabolized in the rumen. Concluding, CAS increased milk fat and modified the milk FA composition by increasing the hydroxy- and oxo-FA. The potential health promoting proprieties and technological advantages of milk enriched with hydroxy- and oxo-FA are not know at present but deserve to be explored.

Ricinus communis L. (castor bean) as a potential candidate for revegetating industrial waste contaminated sites in peri-urban Greater Hyderabad: remarks on seed oil.

Science.gov (United States)

Boda, Ravi Kiran; Majeti, Narasimha Vara Prasad; Suthari, Sateesh

2017-08-01

Ricinus communis L. (castor bean or castor oil plant) was found growing on metal-contaminated sites (4) of peri-urban Greater Hyderabad comprises of erstwhile industrial areas viz Bollaram, Patancheru, Bharatnagar, and Kattedan industrial areas. During 2013-2017, about 60 research papers have appeared focusing the role of castor bean in phytoremediation of co-contaminated soils, co-generation of biomaterials, and environmental cleanup, as bioenergy crop and sustainable development. The present study is focused on its use as a multipurpose phytoremediation crop for phytostabilization and revegetation of waste disposed peri-urban contaminated soils. To determine the plant tolerance level, metal accumulation, chlorophyll, protein, proline, lipid peroxidation, oil content, and soil properties were characterized. It was noticed that the castor plant and soils have high concentration of metals such as cadmium (Cd), lead (Pb), iron (Fe), manganese (Mn), and zinc (Zn). The soils have high phosphorous (P), adequate nitrogen (N), and low concentration of potassium (K). Iron (Fe) concentrations ranged from1672±50.91 to 2166±155.78 mg kg -1 in the soil. The trend of metal accumulation Fe>Zn>Mn>Pb>Cd was found in different plant parts at polluted sites. The translocation of Cd and Pb showed values more than one in industrial areas viz Bollaram, Kattedan, and Bharatnagar indicating the plants resistance to metal toxicity. Chlorophyll and protein content reduced while proline and malondialdehyde increased due to its tolerance level under metal exposure. The content of ricinoleic acid was higher, and the fatty acids composition of polluted areas was almost similar to that of the control area. Thus, R. communis L. can be employed for reclamation of heavy metal contaminated soils.

Greater bottoms upgrading with Albemarle's e-bed catalysts

Energy Technology Data Exchange (ETDEWEB)

Toshima, H.; Sedlacek, Z.; Backhouse, D.; Mayo, S.; Plantenga, F. [Albemarle Catalysts, Houston, TX (United States)

2006-07-01

The E-bed process is a heavy oil upgrading technology that produces near isothermal reactor conditions at a constant catalytic activity. However, E-bed conversion optimization is limited by reactor and downstream fouling problems caused by asphaltene precipitation. While asphaltene precipitation can controlled by reducing hydrogenation, high hydrogenation activity is needed for the removal of sulfur and heavy metals. This presentation described an asphaltene molecule management concept to reduce the fouling of E-bed units. Sediment reduction and high hydrogenation catalysts were used in a modified E-bed process with a variety of feeds and operating conditions. It was observed that the KF1312 catalyst achieved much higher sediment-reduction capability along with satisfactory hydrogenation activity with the different kinds of crude oil sources tested. The catalyst hydrocracked the asphaltenes into smaller molecules, which created greater asphaltene solubility. The sediment reduction capacity of the catalyst-staging technology is now being optimized. It was concluded that the technology will help to reduce fouling in E-bed processes and lead to improved conversion rates for refineries. refs., tabs., figs.

Oxidation of free and encapsulated oil fractions in dried microencapsulated fish oils

Directory of Open Access Journals (Sweden)

Márquez-Ruiz, G.

2000-12-01

Full Text Available The objective of this work was to evaluate oxidation of dried microencapsulated fish oils (DMFO during storage at ambient temperature, and to examine the influence of oils distribution (free vs. encapsulated oil in these complex lipidic systems. DMF0 were prepared by freeze-drying emulsions containing sodium caseinate, lactose and fish oil, with and without adding the antioxidant mixture ALT (ascorbic acid, lecithin and tocopherol. Samples were stored at 25 or 30ºC either in the dark or light with limited, accesible air or under vacuum. The progress of oxidation was followed through quantitation of triglyceride polymers, and oxidation levels of free and encapsulated oil fractions were differentiated. Results showed that oxidation was very rapid both in free and encapsulated oil fractions in all DMFOs exposed to light. In the dark, oxidation was triggered first in the free oil fraction of samples not protected with ALT but, in contrast, samples with ALT showed significantly higher oxidation levels in encapsulated than in free oil fractions, regardless of the limited or free availability of air. These results indicated that addition of the antioxidant system ALT was more effective in the free oil fraction, thus reflecting the great influence of partitioning and/or orientation of antioxidants on their efficacy in complex lipid systems.El objetivo de este trabajo es la evaluación de la oxidación de aceites de pescado microencapsulados en matriz seca (DMFO durante su almacenamiento a temperatura ambiente, y examinar la influencia de la distribución del aceite (aceite libre frente a aceite encapsulado en estos sistemas lipídicos complejos. Las muestras se prepararon mediante liofilización de emulsiones constituidas por caseinato sódico, lactosa y aceite de pescado, con o sin la mezcla antioxidante ALT (ácido ascórbico, lecitina y tocoferol; y se almacenaron a 25 o 30ºC a la luz o a la oscuridad, con aire limitado, accesible o al vac

Assessment of oil pollution as consequence of the oil leaks from seabed pipeline in the Bohai Sea

International Nuclear Information System (INIS)

Wang, J.; Li, X.; Goncharov, V.K.; Klementieva, N.Y.

2005-01-01

Although oil leaks from pipelines are less dangerous than a blowout of oil as a result of a pipeline break, the presence of oil in the ocean can have a devastating affect on the marine environment, particularly as oil leaks are difficult to detect and can occur over long periods of time. This paper discussed oil pollution in the Bohai Sea. Most of the crude oil in the Bohai oil fields is heavy and contains both paraffin and sand, both of which contribute to greater incidences of cracks and corrosion wormholes in pipes. The Main Points of Model for Assessment of Environmental Consequence of the Oil Leaks from Marine Pipeline (MAECOLMP) is based on the assumption that oil leaks from wormholes on seabed pipelines generate separate oil drops which float up to create a plume in the water. After their emergence on the sea surface, an oil slick forms, which has the shape of a serpentine strip extending along the surface in the direction of the current. The main parameters that define environmental oil pollution are: the dimensions of oil drops in the water; the dimension of the oil slick on the sea surface; and the carryover of crude oil on the coastline. According to the model, the assessment of environmental effects of the oil leaks from the sea bed consist of the following stages: selection of the probable position of wormholes in the pipeline and their size; calculation of the rate of the oil leak from the wormhole for selected sizes and positions; estimation of probable average sizes of oil drops for the selected diameter of wormhole; calculation of boundaries of the plume; calculation of the width and extension of the oil slicks for each selected position of the wormhole; and estimation of the volume of crude oil that can be carried over to the coastline in each case and detection of the most dangerous accident variant. This model permits the use of the Lagrangian description in order to take into account the difference in the velocities of emerging oil drops. It

Artificial intelligence applications in offshore oil and gas production

International Nuclear Information System (INIS)

Attia, F.G.

1994-01-01

The field of Artificial Intelligence (AI) has gained considerable acceptance in virtually all fields, of engineering applications. Artificial intelligence is now being applied in several areas of offshore oil and gas operations, such as drilling, well testing, well logging and interpretation, reservoir engineering, planning and economic evaluation, process control, and risk analysis. Current AI techniques offer a new and exciting technology for solving problems in the oil and gas industry. Expert systems, fuzzy logic systems, neural networks and genetic algorithms are major AI technologies which have made an impact on the petroleum industry. Presently, these technologies are at different stages of maturity with expert systems being the most mature and genetic algorithms the least. However, all four technologies have evolved such that practical applications were produced. This paper describes the four major Al techniques and their many applications in offshore oil and gas production operations. A summary description of future developments in Al technology that will affect the execution and productivity of offshore operations will be also provided

Heat transfer efficiency of Al2O3-MWCNT/thermal oil hybrid nanofluid as a cooling fluid in thermal and energy management applications: An experimental and theoretical investigation

DEFF Research Database (Denmark)

Asadi, Amin; Asadi, Meisam; Rezaniakolaei, Alireza

2018-01-01

efficiency of the nanofluid has been evaluated based on different figures of merit. It is revealed that using this nanofluid instead of the base fluid can be beneficial in all the studied solid concentrations and temperatures for both the internal laminar and turbulent flow regimes except the solid...... concentrations of 1 and 1.5% in internal turbulent flow regimes. The effect of adding nanoparticles on pumping power and convective heat transfer coefficient has also been theoretically investigated.......The main objective of the present study is to assess the heat transfer efficiency of Al2O3-MWCNT/thermal oil hybrid nanofluid over different temperatures (25–50 °C) and solid concentrations (0.125%–1.5%). To this end, first of all, the stability of the nano-oil has been studied through the Zeta...

Acid activation of upper Eocene Ca-bentonite for soybean oil clarification.

Science.gov (United States)

Chakroun, Salima; Herchi, Mongi; Mechti, Wafa; Gaied, Mohamed Essghaier

2017-10-01

In central Tunisia, many upper Eocene outcrops supply smectitic claystone which are characterized by several analytical techniques (calcimetry, XRD, SediGraph, chemical analysis, surface area, etc.). Beidellite is the main mineral detected by the XRD method. Representative raw samples M1, taken from Henchir Souar (Zaghouan, Tunisia), were acid activated in order to improve their physicochemical properties. This study consists in optimizing the activation conditions with HCl 3 N by varying the following parameters: time (2, 4, and 6 h) and temperature (25, 50, 75, and 90 °C). The characterization by XRD and chemical analysis was carried out on the samples (M1, activated for 2 and 6 h at 75 °C), showing a structural modification of the clay by reduction of intensity reflection 001 order of smectite and dissolution of metal ions (Al 3+ , Fe 3+ , and Mg 2+ ) from clay structure. Optimum condition for soybean oil clarification is obtained using a variety of amount raw clays (0.5, 0.75, and 1%). Thus, the best clarification yield is given at 0.75% of clay, showing a capacity of about 55%. Various forms of activated materials were used with a 75% proportion to leach soybean oil. Results were compared with commercial bentonite (Tonsil) having surface area (378 m 2 /g). The activated sample M1 during 4 h at 75 °C possesses a decolorizing capacity of about 85% greater than the oil treated by Tonsil in laboratory (58%).

The impact of multiphase behaviour on coke deposition in heavy oil hydroprocessing catalysts

Science.gov (United States)

Zhang, Xiaohui

Coke deposition in heavy oil catalytic hydroprocessing remains a serious problem. The influence of multiphase behaviour on coke deposition is an important but unresolved question. A model heavy oil system (Athabasca vacuum bottoms (ABVB) + decane) and a commercial heavy oil hydrotreating catalyst (NiMo/gamma-Al 2O3) were employed to study the impact of multiphase behaviour on coke deposition. The model heavy oil mixture exhibits low-density liquid + vapour (L1V), high-density liquid + vapour (L2V), as well as low-density liquid + high-density liquid + vapour (L1L2V) phase behaviour at a typical hydroprocessing temperature (380°C). The L2 phase only arises for the ABVB composition range from 10 to 50 wt %. The phase behaviour undergoes transitions from V to L2V, to L1L2V, to L1V with increasing ABVB compositions at the pressure examined. The addition of hydrogen into the model heavy oil mixtures at a fixed mass ratio (0.0057:1) does not change the phase behaviour significantly, but shifts the phase regions and boundaries vertically from low pressure to high pressure. In the absence of hydrogen, the carbon content, surface area and pore volume losses for catalyst exposed to the L1 phase are greater than for the corresponding L2 phase despite a higher coke precursor concentration in L2 than in L1. By contrast, in the presence of hydrogen, the carbon content, surface area and pore volume losses for the catalyst exposed to the L2 phase are greater than for the corresponding L1 phase. The higher hydrogen concentration in L1 appears to reverse the observed results. In the presence of hydrogen, L2 was most closely associated with coke deposition, L1 less associated with coke deposition, and V least associated with coke deposition. Coke deposition is maximized in the phase regions where the L2 phase arises. This key result is inconsistent with expectation and coke deposition models where the extent of coke deposition, at otherwise fixed reaction conditions, is asserted to

Experimental and simulated displacement of oil in sand berea cores using aqueous solutions

International Nuclear Information System (INIS)

Ramirez, A.; Gonzalez, J.L.; Hernandez, F.; Hernandez, H.

2009-01-01

The development of a mathematical algorithm to simulate the displacement of a resident fluid using a displacing one in a saturated anisotropic porous media is shown in this work. The algorithm was included in the simulator developed by the present authors in previous works to represent the anisotropic distribution of the porous media properties and the fluid injection [Ramirez A et al. Mathematical simulation of oil reservoir properties. Chaos, solitons and Fractals 2008;38:778-88, Ramirez A et al. Simulation of uncompressible fluid flow through a porous media. Chaos, Solitons and Fractals 2009;39:1753-63] in a nested loop to analyze the participant nodes in the transport process and calculate the volumes of the resident and new fluids. The new routine developed takes in count the mobility of both fluids. Additionally experimental fluid displacement tests were done using heavy oil from Mexican reservoirs as a resident fluid in sand berea cores. The injection of new fluids in natural oil reservoirs is a part of the Enhanced oil recovery (EOR) methods used to improve the oil displacement and increase production after the primary stage of the oil recovery has been finished. Water is an available and economical resource to be used as a displacing fluid due to many of the producers (off-shores) of the oil industries are placed in the sea near the coast.

Policies for healthy and sustainable edible oil consumption: a stakeholder analysis for Thailand

OpenAIRE

Shankar, Bhavani; Thaiprasert, N.; Gheewala, S.; Smith, R.

2016-01-01

: Palm oil is a cheap and versatile edible oil in widespread use as a food ingredient that has been linked to negative health and environmental outcomes. The current study aimed to understand the prospects for future health-focused policy development to limit food use of palm oil and promote a greater diversity of oils in Thailand's food system. : Eighteen semi-structured interviews were conducted with a range of stakeholders. The interviews probed views on the economic, health and environmen...

Transesterification of soybean oil catalyzed by Sr-doped cinder

International Nuclear Information System (INIS)

Nasreen, Sadia; Liu, Hui; Khan, Romana; Zhu, Xiao-chan; Skala, Dejan

2015-01-01

Highlights: • Sr-doped cinder catalyst was prepared and used for biodiesel synthesis. • A 99% of triglycerides conversion was achieved under optimal reaction conditions. • SrAl 2 Si 2 O 8 and Sr 5 Al 8 O 1 are determined as dominant compounds which are responsible for high catalytic activity. • Catalyst exhibits high activity and can be easily recovered and regenerated. • The Sr-doped cinder catalyst is used in 14 repeated runs. - Abstract: The Strontium doped cinder was prepared using the wet impregnation method and analyzed as catalyst for biodiesel synthesis. Different procedure for cinder impregnation were investigated (temperature and duration of catalyst calcinations, the concentration of SrCl 2 solution) and optimal condition was established: impregnation 20 g of cinder 2–5 mm particles with 0.2 M SrCl 2 solution followed by calcinations at 1000 °C for 4 h. The Sr-cinder activity was tested at 90–200 °C using 1–5% mass of catalyst with different molar ratio of methanol to soybean oil (from 9 to 36). The maximum triglycerides (TG) conversion of 99.0% with the Fatty Acid Methyl Esters (FAME) yield of 97.1% was obtained by using 4% catalyst at 180 °C, for 1 h, and methanol/oil molar ratio 24:1. Influence of free fatty acid (FFA) and water in soybean oil on catalyst activity was analyzed, too. The catalyst could be used for 14 times with TG conversion and FAME yield above 90% and 80% respectively. The Sr-doped cinder catalysts before and after transesterification were characterized using BET surface area, basic strength, X-ray diffraction (XRD), scanning electron microscopy (SEM) and ICP-AAS. Results showed that the formation of SrAl 2 Si 2 O 8 and Sr 5 Al 8 O 17 complexes should be the main reason for the catalytic activity of prepared catalyst. Slow decrease of catalyst activity during its repeated use is result of Sr–Al-glycerolate formation in reaction between Sr–Al complexes and glycerol

The effect of the 2010 Gulf oil spill on public attitudes toward offshore oil drilling and wind development

International Nuclear Information System (INIS)

Lilley, Jonathan; Firestone, Jeremy

2013-01-01

In April 2010, the Deepwater Horizon oil well exploded, releasing over four million barrels of oil into the Gulf of Mexico. This paper presents data from two national mail surveys undertaken in 2008 and 2010 that compare public attitudes to both offshore oil drilling and offshore wind development pre- and post-spill. The results show that while there was a drop in support for expanded drilling (from 66% in 2008 to 59% in 2010) the change was not significant. There was, however, a significant decrease in support for offshore drilling among coastal residents. There was a slight, non-significant increase in support for offshore wind development which remained significantly higher than support for offshore oil (80% in 2008 and 82% in 2010). Despite there being no significant change in overall support levels, there was a shift in the strength of feeling regarding offshore oil, with 80% of Americans either less supportive or more opposed to expanded drilling in 2010 than they were in 2008. -- Highlights: •We assess whether the Gulf oil spill affected attitudes to offshore energy. •Overall support for offshore wind (82%) was greater than for offshore oil (59%). •Support for expanded offshore oil drilling decreased but not significantly. •Support for offshore wind development increased slightly, again not significantly. •Although overall support levels did not change, the strength of feeling did

Influence of the milling process on the structure and morphology of ZnAl{sub 2}O{sub 4} and catalytic performance in the methyl transesterification reaction of soybean oil; Influencia do processo de moagem na estrutura e morfologia de ZnAl{sub 2}O{sub 4} e no desempenho catalitico na reacao de transesterificacao metilica do oleo de soja

Energy Technology Data Exchange (ETDEWEB)

Feitosa, A.C.; Dantas, B.B.; Santana, A.; Costa, A.C.M.F., E-mail: alexcaval2@hotmail.com [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Unidade Academica de Engenharia de Materiais; Costa, D.B. [Universidade Federal de Alagoas (UFAL), Maceio, AL (Brazil). Departamento de Quimica

2012-07-01

This work aimed to evaluate the effect of milling time over the structure and morphology of ZnAl{sub 2}O{sub 4}, synthesized by combustion reaction, and study the effect of milled samples over the methyl transesterification reaction of soy bean oil. ZnAl{sub 2}O{sub 4} was synthesizing, by means combustion reaction, using a electrical resistance plate. The powder was milled over 15, 30, 45 and 60 minutes and the samples were characterized by X-ray diffraction, scanning electron micrograph, particle size distribution and N{sub 2} adsorption isotherms. Milling process promoted changes over the agglomerate size and textural characteristics of the samples. Catalytic tests were conducted at 160 deg C, with 1% of catalyst, with molar ratio oil:methanol of 1:6 and reaction time of 1 hour. According the results, the sample milled over 30 minutes showed the highest conversion. (author)

The US's group of seven: US oil import dependence grows

International Nuclear Information System (INIS)

Anon.

1993-01-01

The latest available import data from the US Department of Energy show greater US dependence on imported crude oil, a two percentage point increase in 1992 above 1991. In fact, the share of imported crude oil of the sum of the US crude production and imports has grown from less than one-third in 1986 to nearly 46% in 1992. A closer look at the data reveals that US crude oil dependence is become increasingly centered on a small number of countries. In 1992, more than 85% of crude oil imports originated in seven countries: Saudia Arabia, Nigeria, Venezuela, Canada, Mexico, Angola, and the United Kingdom. Many people worry that US import dependence is at dangerous levels. However, the recent trend of joint ventures between US companies and oil producers should allay those fears by providing oil producers an incentive for stable oil supply in the US

Virtual Issue #1: Oil Spill Research in the Bulletin of Environmental Contamination and Toxicology

Science.gov (United States)

The Bulletin of Environmental Contamination and Toxicology has been a venue for publishing oil spill research for over forty years. Rehwoldt et al. (1974) published the first oil spill focused paper in the Bulletin, reporting on the aquatic toxicity of two spill mitigating agents...

Modeling of response, socioeconomic, and natural resource damage costs for hypothetical oil spill scenarios in San Francisco Bay

International Nuclear Information System (INIS)

Etkin, D.S.; French McCay, D.; Whittier, N.; Sankaranarayanan, S.; Jennings, J.

2002-01-01

A study was conducted to determine the influence of oil type, spill size, response strategy and location factors on oil spill response costs, with particular reference to the cost benefits of the use of dispersants. Modeling has been conducted for a hypothetical oil spill in San Francisco Bay to determine biological impacts, damages to natural resources and response costs. The SIMAP modeling software by the Applied Science Associates was used to model 3 spill sizes (20, 50 and 95 percentile by volume) and 4 types of oil (gasoline, diesel, heavy fuel oil, and crude oil). Response costs, natural resource damages and socioeconomic impact were determined based on spill trajectory and fate. Mechanical recovery-based operations carry higher response costs than dispersant-based operations. Response costs for diesel and gasoline spills make up 20 per cent of the total costs, compared to 43 per cent for crude and heavy fuel oil spills. Damages to natural resources are higher for spills of toxic lighter fuels such as gasoline and diesel because gasoline has a greater impact on the water column with less shoreline oiling, resulting in more damages to natural resources. Heavier oils have a greater impact on shorelines and higher response and socioeconomic costs. Although socioeconomic costs varied by location, they tend to be greater than response costs and natural resource damage costs. Proportions of the different costs were described with reference to various spill factors. Socioeconomic costs are 61, 76, 45 and 53 per cent respectively for gasoline, diesel, crude oil, and heavy fuel oil spills. 27 refs., 23 tabs., 5 figs

Preparation of Mg/Al-LDHs intercalated with dodecanoic acid and investigation of its antiwear ability

International Nuclear Information System (INIS)

Zhao, Dong; Bai, Zhimin; Zhao, Fuyan

2012-01-01

Graphical abstract: Comparable studies of nano Mg/Al-LDHs powder on the anti-wear properties of lubricating oil were carried out on four-ball and gear testing machine. Mg/Al-NO 3 − -LDHs and Mg/Al-DA-LDHs powder in base oil possess an excellent friction-reducing property, with a friction coefficient at 23.9% and 22.2% which are lower than that of the base oil Highlights: ► We synthesized nano Mg/Al-NO 3 − (DA)-LDHs via coprecipitation and anion exchange. ► The optimal exchanging condition is as follows: water dispersion and pH value of 5. ► The tribological properties of LDHs were studied on four-ball and gear machine. ► We reported nano LHDs as anti-wear materials in lubricates for the first time. ► The greatest decline in friction coefficient of lubricates with LDHs is up to 23.9%. -- Abstract: Layered double hydroxides (LDHs) intercalated with dodecanoic acid have been prepared by anion exchange with Mg/Al-NO 3 − -LDHs as the precursor under acid condition with water and ethanol as the dispersion medium. The obtained materials were characterized by X-ray diffraction (XRD), thermogravimetric and differential thermal analyser (TG–DTA), Fourier transform infrared spectroscopy (FTIR), scanning electron microscope (SEM) and BET. Patterns of XRD and FTIR show that interlayer nitrate ions have substituted with dodecanoic acid and the gallery height has increased from 0.88 nm to 1.99 nm. The interlayer distance of the intercalated materials increases with the increase of pH value due to the different arrangement of interlayer anions. The tribological performance of LDHs precursor and intercalated LDHs in base oil were studied for the first time by using four-ball wear machine and gear testing machine. Experimental results show that the LDHs precursor and intercalated LDHs powder are excellent in friction-reducing, with decreases in friction coefficient by 23.9% and 22.2% respectively comparing with base oil.

Financial assessment of oil palm cultivation on peatland in Selangor, Malaysia

Directory of Open Access Journals (Sweden)

M.N. Noormahayu

2009-02-01

Full Text Available Oil palm plantations on peat soils are generally believed to have greater environmental impacts than those on other soil types. Nonetheless, Malaysia operates substantial incentives to maximise palm oil production, which in practice encourage the establishment of plantations on peatland. This paper explores the social and economic basis of oil palm cultivation on one peatland estate at Sungai Panjang in the state of Selangor, peninsular Malaysia. Data were obtained by conducting a questionnaire survey of 200 farmers who cultivate oil palm on peat soil. Some of the data were cross-tabulated against farmers’ ages in order to identify any age-related trends in education level, the area of land farmed, annual income and knowledge about oil palm cultivation. The Cobb-Douglas production function was used to model the financial output from oil palm in terms of the costs of chemical inputs and labour. The results indicated that cultivation of this crop gives decreasing returns to scale on peatland in Sungai Panjang, and that chemical inputs are more important than labour cost in determining the level of financial output. Finally, the financial viability of oil palm cultivation for farmers was assessed by calculating three financial indicators (NPV, BCR and IRR. This can be a profitable investment so long as growth conditions, costs, selling price and interest rate do not fluctuate substantially. Greater annual returns can be achieved over 20–25 years than over shorter periods, especially of less than 10 years.

Weight-length Relationships, Gonadosomatic Indeces, Sex Ratios and Relative Weight of the Omani-Indian Oil sardine, Sardinella longiceps (Valenciennes1847) from Al-Seeb Area; Sultanate of Oman

OpenAIRE

Al-Jufaili Saud

2011-01-01

This study presents the weight-length relationship and spawning period of the Omani Indian Oil sardine Sardinella longiceps (Valenciennes 1847) which inhabits the near shore zone along the Omani coast. A total of 1744 specimens were collected between January 1997 to February 1998 from Al-Seeb; a suburban area situated by the sea in Muscat, Oman. Samples were obtained on a monthly basis from beach seine and gillnet catches. The female to male sex ratio was obtained to be 0.6. The monthly varia...

DEGRADAÇÃO TÉRMICA DE TOCOFEROL E PRODUTOS DE OXIDAÇÃO EM DIFERENTES CLASSES DE AZEITE DE OLIVA UTILIZANDO ESPECTROSCOPIA UV-VIS E MCR-ALS

Directory of Open Access Journals (Sweden)

Rhayanna P. Gonçalves

2015-07-01

Full Text Available Extra virgin olive oil, virgin olive oil and mixed oil were analyzed by UV-Vis spectroscopy and Multivariate Curve Resolution with Alternating Least Squares (MCR-ALS. When the oils were heated at high temperatures (frying, oxidation products were formed which were harmful to human health and antioxidants present were degraded. The aim of this study was to evaluate tocopherol (an antioxidant present in oils and the behaviour of oxidation products in different olive oil classes. MCR-ALS results showed that degradation started at 70 ºC for extra virgin olive oil, while tocopherol concentration decreased and oxidation products increased starting at 40 ºC in virgin olive oil. In mixed oil, commercialized as a mixture of 85% soybean oil and 15% olive oil, tocopherol concentration started to decrease and oxidation products increase at 30 ºC. The results suggested that extra virgin olive oil offered more resistance to increasing temperatures, while virgin olive oil and mixed oil were less resistant.

Influence of salinity on bioremediation of oil in soil

International Nuclear Information System (INIS)

Rhykerd, R.L.; Weaver, R.W.; McInnes, K.J.

1995-01-01

Spills from oil production and processing result in soils being contaminated with oil and salt. The effect of NaCl on degradation of oil in a sandy-clay loam and a clay loam soil was determined. Soils were treated with 50 g kg -1 non-detergent motor oil (30 SAE). Salt treatments included NaCl amendments to adjust the soil solution electrical conductivities to 40, 120, and 200 dS m -1 . Soils were amended with nutrients and incubated at 25 o C. Oil degradation was estimated from the quantities of CO 2 evolved and from gravimetric determinations of remaining oil. Salt concentrations of 200 dS m -1 in oil amended soils resulted in a decrease in oil mineralized by 44% for a clay loam and 20% for a sandy-clay loam soil. A salt concentration of 40 dS m -1 reduced oil mineralization by about 10% in both soils. Oil mineralized in the oil amended clay-loam soil was 2-3 times greater than for comparable treatments of the sandy-clay loam soil. Amending the sandy-clay loam soil with 5% by weight of the clay-loam soil enhanced oil mineralization by 40%. Removal of salts from oil and salt contaminated soils before undertaking bioremediation may reduce the time required for bioremediation. (author)

The Worldwide Oil Spill Model (WOSM)

International Nuclear Information System (INIS)

Anderson, E.L.; Howlett, E.; Jayko, K.; Reed, M.; Spaulding, M.; Kolluru, V.

1993-01-01

The Worldwide Oil Spill Model (WOSM) is a standalone microcomputer-based state-of-the-art oil spill model system for use in oil spill response decision support, planning, research, training, and contingency planning. WOSM was developed under support provided by a consortium of oil companies and government agencies. WOSM represents the next generation of oil spill model beyond the OILMAP modelling system (Spaulding et al, 1992). WOSM is designed in a shell architecture in which the only parameters that change are those that describe the area in which the spill model is to be applied. A limited function geographic information system (GIS) is integrated within the model system, and the spill modelling shell has been extended to include interfaces to other GIS systems and digital data. WOSM contains all the databases, data manipulation and graphical display tools, and models to simulate any type of oil spill. The user has control over which weathering processes are to be modelled, and WOSM data input tools enable continual refinement of model predictions as more refined data is imported. Use of WOSM is described and illustrated, showing sample screens and applications. WOSM algorithms and file structure are also outlined. An example test case of a spill in the Juan de Fuca strait is included. 29 refs., 7 figs., 1 tab

The effects of spilled oil on coastal ecosystems: Lessons from the Exxon Valdez spill: Chapter 11

Science.gov (United States)

Bodkin, James L.; Esler, Daniel N.; Rice, Stanley D.; Matkin, Craig O.; Ballachey, Brenda E.; Maslo, Brooke; Lockwood, Julie L.

2014-01-01

Oil spilled from ships or other sources into the marine environment often occurs in close proximity to coastlines, and oil frequently accumulates in coastal habitats. As a consequence, a rich, albeit occasionally controversial, body of literature describes a broad range of effects of spilled oil across several habitats, communities, and species in coastal environments. This statement is not to imply that spilled oil has less of an effect in pelagic marine ecosystems, but rather that marine spills occurring offshore may be less likely to be detected, and associated effects are more difficult to monitor, evaluate, and quantify (Peterson et al., 2012). As a result, we have a much greater awareness of coastal pollution, which speaks to our need to improve our capacities in understanding the ecology of the open oceans. Conservation of coastal ecosystems and assessment of risks associated with oil spills can be facilitated through a better understanding of processes leading to direct and indirect responses of species and systems to oil exposure.It is also important to recognize that oil spilled from ships represents only ~9% of the nearly 700 000 barrels of petroleum that enter waters of North America annually from anthropogenic sources (NRC, 2003). The immediate effects of large spills can be defined as acute, due to the obvious and dramatic effects that are observed. In contrast, the remaining 625 000 barrels that are released each year can be thought of as chronic non-point pollution, resulting from oil entering the coastal ocean as runoff in a more consistent but much less conspicuous rate. In this chapter, we primarily address the effects of large oil spills that occur near coastlines and consider their potential for both acute and chronic effects on coastal communities. As described below, in some instances, the effects from chronic exposure may meet or exceed the more evident acute effects from large spills. Consequently, although quantifying chronic effects

Transesterification of jojoba oil, sunflower oil, neem oil, rocket seed oil and linseed oil by tin catalysts

International Nuclear Information System (INIS)

Shah, Mazloom; Tariq, Muhammad; Ali, Saqib; Guo, Qing-Xiang; Fu, Yao

2014-01-01

The methanolysis of jojoba oil has been studied in the presence of tin powder, dibutyltin diacetate (C 4 H 9 ) 2 Sn(OOCCH 3 ) 2 , dioctyltin diacetate (C 8 H 17 ) 2 Sn(OOCCH 3 ) 2 , dibutyltin oxide (C 4 H 9 ) 2 SnO, dioctyltin oxide (C 8 H 17 ) 2 SnO, diphenyltin oxide (C 6 H 5 ) 2 SnO, dibutyltin chloride dihydroxide (C 4 H 9 ) 2 Sn(OH) 2 Cl, butyltinhydroxide hydrate (C 4 H 9 )Sn(=O)OH.xH 2 O, Ni nanoparticles and Pd nanoparticles act as catalysts. Among these, 1 weight % of dibutyltin diacetate shows the maximum conversion. Then, methanolysis of sunflower oil, neem oil, rocket seed oil and linseed oil into methyl esters studied in the presence of 1% dibutyltin diacetate as a catalyst and was compared their percentage conversions. The experimental yield for the conversion of jojoba oil, sunflower oil, neem oil, rocket seed oil and linseed oil into biodiesel was found to be 71%, 51%, 50.78%, 40.90% and 39.66%, respectively. The experimental yield of the conversion of jojoba oil into methyl esters was found to be increased up to 96% by increasing reaction time, without emulsion formation. The synthesis of jojoba seed oil biodiesel (JSOB), soybean oil biodiesel (SOB), neem oil biodiesel (NOB), rocket seed oil biodiesel (RSOB) and linseed oil biodiesel (LSOB) was confirmed by NMR ( 1 H and 13 C) and FT-IR analyses of biodiesel. - Highlights: • Transesterification of jojoba oil into biodiesel by tin and nano catalysts. • 1 weight % dibutyltin diacetate showed highest yield at 60 °C. • Catalytic conversion comparison of five oils using dibutyltin diacetate • The experimental yield of the conversion of jojoba oil increased with time. • FT-IR and NMR ( 1 H and 13 C) characterization

Unconventional uses for unconventional oil

International Nuclear Information System (INIS)

Ehlig-Economides, C.A.; Barrufet, M.; Longbottom, J.R.; Velu, B.P.

2005-01-01

The transportation sector in the United States is 95 per cent dependent on oil, which is the only primary fuel that is being imported to the country in great quantities. It has been proposed that energy independence may come by supplying electric power with renewable energy sources. It was also suggested that the best solution for future transportation may be to develop electrified guideways that would provide energy to automatically convey personal cars and driverless freight through the roadways. Advantages include zero vehicle emissions, greater safety and decreased road congestion. This paper examined the option of using heavy oil for power generation instead of the current expensive refining practices designed to produce liquid transportation fuels from heavy oil. It compared coal gasification with heavy oil for power generation. The cost to consumers and environmental impacts were considered. The comparison of conventional versus electrified transportation options was based on on a well-to-mine-to-wheels cycle. It was shown that electrified transportation is attractive from a cost, environmental and energy security perspective. If the United States were to import Canadian heavy oil only for transportation, the consumer cost will increase by approximately 25 per cent based on 2003 data. If the United States were to transform transportation from conventional to electrified transportation, the cost of using Canadian heavy oil will be less, even including carbon dioxide capture. It was concluded that all primary fuel sources would seek new equilibrium prices that may affect comparisons between heavy oil and coal. 14 refs., 4 tabs., 10 figs

Unconventional uses for unconventional oil

Energy Technology Data Exchange (ETDEWEB)

Ehlig-Economides, C.A.; Barrufet, M.; Longbottom, J.R.; Velu, B.P. [Texas A and M Univ., Austin, TX (United States)

2005-11-01

The transportation sector in the United States is 95 per cent dependent on oil, which is the only primary fuel that is being imported to the country in great quantities. It has been proposed that energy independence may come by supplying electric power with renewable energy sources. It was also suggested that the best solution for future transportation may be to develop electrified guideways that would provide energy to automatically convey personal cars and driverless freight through the roadways. Advantages include zero vehicle emissions, greater safety and decreased road congestion. This paper examined the option of using heavy oil for power generation instead of the current expensive refining practices designed to produce liquid transportation fuels from heavy oil. It compared coal gasification with heavy oil for power generation. The cost to consumers and environmental impacts were considered. The comparison of conventional versus electrified transportation options was based on on a well-to-mine-to-wheels cycle. It was shown that electrified transportation is attractive from a cost, environmental and energy security perspective. If the United States were to import Canadian heavy oil only for transportation, the consumer cost will increase by approximately 25 per cent based on 2003 data. If the United States were to transform transportation from conventional to electrified transportation, the cost of using Canadian heavy oil will be less, even including carbon dioxide capture. It was concluded that all primary fuel sources would seek new equilibrium prices that may affect comparisons between heavy oil and coal. 14 refs., 4 tabs., 10 figs.

Pediatric Age Palm Oil Consumption.

Science.gov (United States)

Di Genova, Lorenza; Cerquiglini, Laura; Penta, Laura; Biscarini, Anna; Esposito, Susanna

2018-04-01

Palm oil is widely used in the food industry for its chemical/physical properties, low cost and wide availability. Its widespread use has provoked an intense debate about whether it is a potential danger to human health. In a careful review of the scientific literature, we focused on nutritional characteristics and health effects of the use of palm oil with regards to children, seeking to determine whether there is evidence that justifies fears about the health effects of palm oil. Our review showed that palm oil represents a significant source of saturated fatty acids, to which scientific evidence attributes negative health effects when used in excess, especially with regards to cardiovascular diseases. However, to date, there is no evidence about the harmful effects of palm oil on the health of children. Nevertheless, palm oil has possible ill health effects linked to its composition of fatty acids: its consumption is not correlated to risk factors for cardiovascular diseases in young people with a normal weight and cholesterol level; the elderly and patients with dyslipidaemia or previous cardiovascular events or hypertension are at a greater risk. Therefore, the matter is not palm oil itself but the fatty-acid-rich food group to which it belongs. The most important thing is to consume no more than 10% of saturated fatty acids, regardless of their origin and regardless of one's age. Correct information based on a careful analysis of the scientific evidence, rather than a focus on a singular presumed culprit substance, should encourage better lifestyles.

Generation and migration of Bitumen and oil from the oil shale interval of the Eocene Green River formation, Uinta Basin, Utah

Science.gov (United States)

Johnson, Ronald C.; Birdwell, Justin E.; Mercier, Tracey J.

2016-01-01

The results from the recent U.S. Geological Survey assessment of in-place oil shale resources of the Eocene Green River Formation, based primarily on the Fischer assay method, are applied herein to define areas where the oil shale interval is depleted of some of its petroleum-generating potential along the deep structural trough of the basin and to make: (1) a general estimates of the amount of this depletion, and (2) estimate the total volume of petroleum generated. Oil yields (gallons of oil per ton of rock, GPT) and in-place oil (barrels of oil per acre, BPA) decrease toward the structural trough of the basin, which represents an offshore lacustrine area that is believed to have originally contained greater petroleum-generating potential than is currently indicated by measured Fischer assay oil yields. Although this interval is considered to be largely immature for oil generation based on vitrinite reflectance measurements, the oil shale interval is a likely source for the gilsonite deposits and much of the tar sands in the basin. Early expulsion of petroleum may have occurred due to the very high organic carbon content and oil-prone nature of the Type I kerogen present in Green River oil shale. In order to examine the possible sources and migration pathways for the tar sands and gilsonite deposits, we have created paleogeographic reconstructions of several oil shale zones in the basin as part of this study.

Effect of chemically reduced palladium supported catalyst on sunflower oil hydrogenation conversion and selectivity

Directory of Open Access Journals (Sweden)

Abdulmajid Alshaibani

2017-02-01

Full Text Available Catalytic hydrogenation of sunflower oil was studied in order to improve the conversion and to reduce the trans-isomerization selectivity. The hydrogenation was performed using Pd–B/γ-Al2O3 prepared catalyst and Pd/Al2O3 commercial catalyst under similar conditions. The Pd–B/γ-Al2O3 catalyst was prepared by wet impregnation and chemical reduction processes. It was characterized by Brunauer–Emmett–Teller surface area analysis (BET, X-ray powder diffraction (XRD, scanning electron microscopy (SEM, and transmission electron microscopy (TEM. The result of sunflower oil hydrogenation on Pd–B/γ-Al2O3 catalyst showed a 17% higher conversion and a 23% lower trans-isomerization selectivity compared to the commercial Pd/Al2O3 catalyst. The chemical reduction of palladium supported catalyst using potassium borohydride (KBH4 has affected the Pd–B/γ-Al2O3 catalyst’s structure and particle size. These most likely influenced its catalytic performance toward higher conversion and lower trans-isomerization selectivity.

Role of oil imports in economic development

International Nuclear Information System (INIS)

Madduri, V.B.N.S.; Radhika, G.

1990-01-01

This paper reports that energy has a vital role to play in a developing economy. The process of industrialization calls for continuous increase in energy use. In general, the greater the use of energy, the higher the economy is placed in the order of developed countries. Countries with high per-capita income have a high consumption level of energy too. On a per-capita basis, energy consumed in U.S.A. is 51.7 barrels of oil equivalent per year while in India, it is 0.9 barrels of oil equivalent only. Therefore, energy consumption, industrial development and economic growth are interlinked. Energy became a significant part in the process of development. In the case of developing countries, any change in the price of oil has a negative effect on economic growth. It was stated in one of the Oil and Natural Gas Commission reports that a fivefold increase in the international price of oil, in real terms, over the past 15 years has had profound effects on balance of payments and growth prospects in developing countries

Hydrodesulfurization of Iraqi Atmospheric Gasoil by Ti-Ni-Mo/γ-Al2O3 Prepared Catalyst

Directory of Open Access Journals (Sweden)

Abdul Halim Abdul Karim Mohammed

2017-11-01

Full Text Available This study investigates the improvement of Iraqi atmospheric gas oil characteristics which contains 1.402 wt. % sulfur content and 16.88 wt. % aromatic content supplied from Al-Dura Refinery by using hydrodesulfurization (HDS process using Ti-Ni-Mo/γ-Al2O3 prepared catalyst in order to achieve low sulfur and aromatic saturation gas oil. Hydrodearomatization (HDA occurs simultaneously with hydrodesulfurization (HDS process. The effect of titanium on the conventional catalyst Ni-Mo/γ-Al2O3 was investigated by physical adsorption and catalytic activity test.Ti-Ni-Mo/γ-Al2O3 catalyst was prepared under vacuum impregnation condition to ensure efficient precipitation of metals within the carrier γ-Al2O3. The loading percentage of metals as oxide; titanium oxide 3 wt. %, nickel oxide 5 wt. % and molybdenum oxide 12 wt. %. The performance of the synthesized catalyst for removing sulfur and aromatic saturation were tested at various temperatures 275 to 350°C, LHSV 1 to 4h-1, constant pressure 40 bar and H2/HC ratio 500 ml/ml.Results showed that the sulfur and aromatic content were reduced at all operating conditions. Maximum sulfur removal was 75.52 wt. % in gas oil on Ti-Ni-Mo/γ-Al2O3 at temperature 350˚C, LHSV 1h-1, while minimum aromatic content achieved was 15.6 wt. % at the same conditions.

Energetic Efficiency of red palm oil

Directory of Open Access Journals (Sweden)

Byron Jiménez

2013-11-01

Full Text Available The main goal of this paper is to determine the energy efficiency in the production of red palm oil (Elaeis guineensis by using the biophysical indicator EROI, postulated by the Ecological Economics. This indicator is applied to compare the energy used in the preparation of synthetic fertilizers (to fill its nutritional demands versus the energy contained in the oil. In 2009, there were 195.550 hectares of land planted with African palm in Ecuador (INEC, 2011. In addition, between 2002 and 2009, there were 2,7 million tons of red oil (FEDEPAL, 2010. It is determined that for each unit of energy consumed, 4.82 units of energy are contained in the red oil. The energy used in making pesticides for cultivation, consumed in transportation, refining, and post harvest is excluded because this other energy would drastically reduce the absolute data of the indicator, which is already inefficient for the high energy consumption it requires to generate the energy contained in the oil. On the other hand, agroecology has proven to be more efficient in the generation of energy per unit of invested energy (Altieri et. al., 2010; Moore, 2004.

Upgrading of raw tall oil soap into fuel oils and lubricants. Final report; Raakasuovan jalostus poltto- ja voiteluoeljyksi. Loppuraportti

Energy Technology Data Exchange (ETDEWEB)

Oasmaa, A.; Arpiainen, V.; McKeough, P.

1997-12-31

Thermochemical processing of tall oil soap originating from various mixtures of birch and pine has been experimentally investigated. The organic matter of tall oil soap, which is a by- product of Kraft pulping, originated mainly from wood extractives. Conventional processing of tall oil soap involves acidification with sulfuric acid to yield crude tall oil and subsequent distillation of the oil at centralized refineries. Because tall oil originating from birch wood is far less valuable than that from pine, there is an economic incentive in the Nordic Countries to develop alternative conversion processes for the tall oil soap produced at pulp mills where birch is widely used as feedstock. Furthermore, thermochemical processing of tall oil soap does not introduce sulfur into the chemical recovery cycle. This would be a significant advantage in future mills employing closure of water circuits and/or sulfur-free pulping. In small-scale experiments tall oil soaps from wood mixtures with high birch content have been processed using both liquid-phase thermal treatment and pyrolysis. The liquid-phase thermal treatment at 450 deg C under a nitrogen atmosphere yielded a good-quality oil product at high yield (about 50 % of the energy content of the tall oil soap). Also in the atmospheric pyrolysis of birch tall oil soap a separation of inorganic and organic constituents was obtained. The energy value of the product gases was high. Both processes are promising, but the pyrolysis alternative has the greater economic potential, providing that the promising preliminary experimental results have given a true picture of the performance of the full-scale pyrolysis process Bioenergy Research Programme; 3 refs., 3 figs.

Production and characterization of refined oils obtained from Indian oil sardine (Sardinella longiceps).

Science.gov (United States)

Chakraborty, Kajal; Joseph, Deepu

2015-01-28

Crude Sardinella longiceps oil was refined in different stages such as degumming, neutralization, bleaching, and deodorization. The efficiency of these processes was evaluated on the basis of free fatty acid (FFA), peroxide (PV), p-anisidine (pAV), total oxidation (TOTOX), thiobarbituric acid reactive species (TBARS) values, Lovibond CIE-L*a*b* color analyses, and (1)H NMR or GC-MS experiments. The utilities of NMR-based proton signal characteristics as new analytical tools to understand the signature peaks and relative abundance of different fatty acids and monitoring the refining process of fish oil have been demonstrated. Phosphoric acid (1%) was found to be an effective degumming reagent to obtain oil with the lowest FFA, PV, pAV, TOTOX, and TBARS values and highest color reduction. Significant reduction in the contents of hydrocarbon functionalities as shown by the decrease in proton integral in the characteristic (1)H NMR region was demonstrated by using 1% H3PO4 during the course of the degumming process. A combination (1.25:3.75%) of activated charcoal and Fuller's earth at 3% concentration for a stirring time of 40 min was found to be effective in bleaching the sardine oil. This study demonstrated that unfavorable odor-causing components, particularly low molecular weight carbonyl compounds, could successfully be removed by the refining process. The alkane-dienals/alkanes, which cause unfavorable fishy odors, were successfully removed by distillation (100 °C) under vacuum with aqueous acetic acid solution (0.25 N) to obtain greater quality of refined sardine oil, a rich source of essential fatty acids and improved oxidative stability. The present study demonstrated that the four-stage refinement process of sardine oil resulted in a significant improvement in quality characteristics and nutritional values, particularly n-3 PUFAs, with improved fish oil characteristics for use in the pharmaceutical and functional food industries.

Hydrodeoxygenation of Guaiacol Over Pt/Al-SBA-15 Catalysts.

Science.gov (United States)

Yu, Mi Jin; Park, Sung Hoon; Jeon, Jong-Ki; Ryu, Changkook; Sohn, Jung Min; Kim, Sang Chai; Park, Young-Kwon

2015-01-01

Upgrading of bio-oil through catalytic hydrodeoxygenation (HDO) reaction was investigated for guaiacol as a model compound. A batch reactor was used for the reaction condition of 40 bar and 250 degrees C. The target product was cyclohexane. Pt/Al-SBA-15 with the Si/Al ratios of 20, 40, and 80 and Pt/HZSM-5 were used as the catalyst. The SBA-15 catalysts were characterized by N2 adsorption-desorption, X-ray diffraction analysis, and temperature programmed desorption of ammonia. The order of cyclohexane yield was Pt/Al-SBA-15 (Si/Al = 20) > Pt/Al-SBA-15(40) > Pt/Al-SBA-15 (80), indicating that the quantity of acid sites plays an important role in the HDO reaction. On the other hand, Pt/HZSM-5 led to a very low cyclohexane yield, in spite of its abundant strong acid sites, due to its small pore size.

The Anglo-Iranian oil dispute

International Nuclear Information System (INIS)

Ferrier, R.W.

1988-01-01

This paper traces the history of the Anglo-Iranian oil dispute. It is short-sighted to consider the Anglo-Iranian oil dispute just as a contest between Musaddiq and the AIOC: it is of wider and greater significance. The dispute illustrates a transitional phase in the difficult process of the adjustment of relations between industrialized and less developed societies for the exploitation of raw materials. Oil was already becoming a political and economic factor at the end of the Qajar period and became important during the reign of Riza Shah with his emphasis on a national program of modernization. After more attention had been focused on it during the second world war it was inevitable that it would increase in influence. The issues of the oil dispute referred back to the concessional controversies of the late nineteenth century in tobacco, mining, communications, utilities, banking even gambling, with their political and social implications; and they referred forward to the issues of the sovereignty of national resources, the transfer of technology and economic growth in relation to the standard of living. These are aspects of the North-South debate, which have yet to be satisfactorily resolved

The Discovery of Deep Oil Plumes at the Deepwater Horizon Oil Spill Site (Invited)

Science.gov (United States)

Diercks, A. R.; Asper, V. L.; Highsmith, R. C.; Woolsey, M.; Lohrenz, S. E.; McLetchie, K.; Gossett, A.; Lowe, M., III; Joung, D.; McKay, L.

2010-12-01

was discovered at 1200 to 1400 m depth. This layer was detected by three independent sensors, CDOM (colored dissolved organic matter) fluorometer, beam transmissometer, and dissolved oxygen sensor. All three instruments responded in unison with greater fluorescence and beam attenuation and decreased O2 concentration. These signals were first observed at a station 5 miles from the accident site. Second and third station measurements at 2.5 miles, and at 1.25 miles from the spill site, showed the same signal but with significantly greater magnitude. Following this discovery, the sampling plan for the remaining days of the cruise was changed to map the newly discovered feature. This paper will discuss our data acquired during this cruise aboard the RV Pelican and its original discovery of the deep oil plumes from the Deepwater Horizon well.

Cracking vegetable oil from Callophylluminnophyllum L. seeds to bio-gasoline by Ni-Mo/Al2O3 and Ni-Mo/Zeolite as micro-porous catalysts

Science.gov (United States)

Savitri, Effendi, R.; Tursiloadi, S.

2016-02-01

Natural minerals such as zeolite are local natural resources in the various regions in Indonesia. Studies on the application of natural mineral currently carried out by national research institutions, among others, as a filler, bleaching agent, or dehydration agent. However, not many studies that utilize these natural minerals as green catalysts material which has high performance for biomass conversion processes and ready to be applied directly by the bio-fuel industry. The trend movement of green and sustainable chemistry research that designing environmentally friendly chemical processes from renewable raw materials to produce innovative products derived biomass for bio-fuel. Callophylluminnophyllum L. seeds can be used as raw material for bio-energy because of its high oil content. Fatty acid and triglyceride compounds from this oil can be cracked into bio-gasoline, which does not contain oxygen in the hydrocarbon structure. Bio-gasoline commonly is referred to as drop-in biofuel because it can be directly used as a substitute fuel. This paper focused on the preparation and formulation of the catalyst NiMo/H-Zeolite and Ni-Mo/Al2O3 which were used in hydro-cracking process of oil from Callophylluminnophyllum L. seeds to produce bio-gasoline. The catalysts were analyzed using XRD, BET and IR-adsorbed pyridine method. The results of hydro-cracking products mostly were paraffin (C10-C19) straight chain, with 59.5 % peak area based on GC-MS analysis.

Hydrogenation of Estonian oil shale and shale oil

Energy Technology Data Exchange (ETDEWEB)

Kogerman, P N; Kopwillem, J

1932-01-01

Kukersite was heated in an atmosphere of hydrogen, nitrogen, or water in three series of experiments. Shale samples were heated at 370/sup 0/ to 410/sup 0/C for 2 to 3/sup 1///sub 2/ hours in the presence of 106 to 287 kg/sq cm pressure of water, nitrogen, or hydrogen. In some experiments 5 percent of iron oxide was added to the shale. The amount of kerogen liquefied by hydrogenation was not greater than the amount of liquid products obtained by ordinary distillation. On hydrogenation, kukersite absorbed 1.8 weight-percent of hydrogen. Almost no hydrogenation took place below the decomposition point of kerogen, and the lighter decomposition products were mainly hydrogenated. Hydrogenation of the shale prevented coke formation. Heating kukersite or its crude oil at temperatures of 400/sup 0/ to 410/sup 0/C under 250 kg/sq cm hydrogen pressure produced paraffinic and naphthenic oils of lower boiling points. At higher temperatures and after long-continued heating, the formation of aromatic hydrocarbons was observed.

Promoting landscape heterogeneity to improve the biodiversity benefits of certified palm oil production: Evidence from Peninsular Malaysia

Directory of Open Access Journals (Sweden)

Badrul Azhar

2015-01-01

Full Text Available The Roundtable on Sustainable Palm Oil (RSPO is responsible for the certification of palm oil producers that comply with sustainability standards. However, it is not known whether RSPO-certified plantations are effective in maintaining biodiversity. Focusing on Peninsular Malaysia, we show that both RSPO-certified plantations and uncertified large-scale plantations are characterized by very low levels of landscape heterogeneity. By contrast, heterogeneity measures were many times higher in palm oil producing smallholdings, despite their lack of RSPO certification. The low heterogeneity of large-scale oil palm plantations, including those certified by the RSPO, is likely to severely limit their value for biodiversity conservation. Uncertified smallholdings, in contrast, are much more heterogeneous and therefore hold substantially greater promise for the integration of palm oil production and biodiversity conservation than large-scale plantations. With oil palm agriculture further expanding, certification schemes should mandate producers to improve biodiversity conservation through landscape management that promotes greater landscape heterogeneity.

Extra heavy oil and refinery residues upgrading through Eni Slurry Technology : first EST commercial unit

Energy Technology Data Exchange (ETDEWEB)

Rispoli, G.; Sanfilippo, D.; Amoroso, A [Eni S.p.A., Rome (Italy)

2009-07-01

The production of heavy crude oils is projected to continue to grow in the upstream oil industry given that large reserves of unconventional extra heavy crude and bitumen exist in several geographic areas including Canada and Venezuela. As reserves of conventional crude oil continue to decline, these unconventional feedstocks are becoming an opportunity to pursue, but they require effective technologies for upgrading and meeting the growing demand for light and middle distillate fuels. This paper described the proprietary technology that offers a solution to upstream and downstream oil producers for bottom-of-the-barrel upgrading. En i Slurry Technology (EST) is constructing an industrial plant in its Sannazzaro refinery in Italy. The plant is designed to convert 23,000 BPSD of vacuum residue into high quality diesel and other valuable refinery streams such as liquefied petroleum gas, naphtha and jet fuel. EST is an H-addition process characterized by the use of a special homogeneous isothermal intrinsically safe reactor, and of a nano-dispersed non-ageing catalyst. EST converts more than 98 per cent of any type of residues to about 110 per cent volume of light products and distillates or extra heavy oils to high quality bottomless SCO. In typical performance, HDS is greater than 85 per cent, HDM greater than 99 per cent and HDCCR greater than 97 per cent. EST also achieves the target of zero fuel oil - zero coke. 12 refs., 4 tabs., 5 figs.

Physical, chemical and biological observations and modeling of oil spills in the Mediterranean Sea

Science.gov (United States)

Ribotti, A.; De Dominicis, M.

2016-11-01

According to a definition of GESAMP, United Nations advisory body on scientific aspects of marine protection, a marine pollution is: "direct or indirect introduction by man of substances or energy into the marine environment … which results in such deleterious effects as harm to living resources, hazard to human health, hindrance to marine activities including fishing, impairment of water quality and reduction of marine attractions". The works presented in this Special Issue stem from the need to manage the problem of marine pollution. The categories of pollutants associated with the maritime traffic are mainly hydrocarbons and chemicals. Hydrocarbon is the oil in all its forms, including the crude oil, the fuel oil, the sludges, debris and other refined products (as defined by MARPOL 73/78 Annex I (MARPOL, 1978)). An oil spill is a release of a liquid petroleum hydrocarbon into the environment due to human activity, and is a form of pollution. The term often refers to marine oil spills, where oil is released into the open ocean or coastal waters. Oil spills include releases of crude oil from tankers, offshore platforms, drilling rigs and wells, as well as spills of refined petroleum products (such as gasoline, diesel) and their by-products, and heavier fuels used by large ships such as bunker fuel, or the spill of any oily refuse or waste oil. Oil spills can have devastating effects on the marine environment and can jeopardize the functional integrity of the marine ecosystem (seabirds populations, fish communities, and marine mammals), as reported in Jackson et al. (1989), Piatt and Anderson (1996), Peterson et al. (2003). While being toxic to marine life, the hydrocarbons are very difficult to clean up, and last for years in the sediment and marine environment. Discharge of cargo residues from bulk carries can pollute ports, waterways and oceans. In many instances vessels intentionally discharge illegal wastes despite foreign and domestic regulation prohibiting

Essential Oils as Biocides for the Control of Fungal Infections and Devastating Pest (Tuta absoluta) of Tomato (Lycopersicon esculentum Mill.).

Science.gov (United States)

Bouayad Alam, Samira; Dib, Mohammed El Amine; Djabou, Nassim; Tabti, Boufeldja; Gaouar Benyelles, Nassira; Costa, Jean; Muselli, Alain

2017-07-01

Thymus capitatus and Tetraclinis articulata essential oils as well their major components (carvacrol and α-pinene) were evaluated for their antifungal and insecticidal activities. Both oils showed good in vitro antifungal activity against Fusarium oxysporum, Aspergillus niger, Penicillium sp., Alternaria alternata, and Botrytis cinerea, the fungi causing tomato rot. In vivo results indicate the efficacies of both essential oils and carvacrol of reduce postharvest fungal pathogens, such as B. cinerea and Al. alternata that are responsible of black and gray rot of tomato fruit. Disease incidence of Al. alternata and B. cinerea decreased on average from 55% to 80% with essential oil of Th. capitatus and pure carcvacrol, while Te. articulata essential oil exhibited inhibition of fungal growth of 55% and 25% against Al. alternata and B. cinerea, respectively, with concentration of 0.4 μl/l air. The insecticidal activity of Th. capitatus and Te. articulata essential oils exhibited also a good insecticidal activity. At the concentration of 0.2 μl/ml air, the oils caused mortality over 80% for all larval stages of Tuta absoluta and 100% mortality for the first-instar after 1.5 h only of exposure. α-Pinene presented lower insecticidal and antifungal activities compared to essential oils of Th. capitatus, Te. articulata and pure carvacrol. Thus, these essential oils can be used as a potential source to develop control agents to manage some of the main pests and fungal diseases of tomato crops. © 2017 Wiley-VHCA AG, Zurich, Switzerland.

Policies for healthy and sustainable edible oil consumption: a stakeholder analysis for Thailand.

Science.gov (United States)

Shankar, Bhavani; Thaiprasert, Nalitra; Gheewala, Shabbir; Smith, Richard

2017-04-01

Palm oil is a cheap and versatile edible oil in widespread use as a food ingredient that has been linked to negative health and environmental outcomes. The current study aimed to understand the prospects for future health-focused policy development to limit food use of palm oil and promote a greater diversity of oils in Thailand's food system. Eighteen semi-structured interviews were conducted with a range of stakeholders. The interviews probed views on the economic, health and environmental dimensions of the issue, the prospects for health-focused policy development and the policy development process. Transcripts were analysed using a health policy analytical framework. Thailand. Stakeholders from a range of ministries, regulatory agencies, the private sector, non-governmental organizations and academia. There are several impediments to the emergence of strong regulation, including the primacy of economic considerations in setting policy, doubt and misperception about health implications and a complex regulatory environment with little space for health-related considerations. At the same time, some sections of the food industry producing food for domestic consumption are substituting palm with other oils on the basis of consumer health perceptions. Strong regulation to curb the growth of palm oil is unlikely to emerge soon. However, a long-term strategy can be envisaged that relies on greater policy support for other indigenous oils, strategic rebalancing towards the use of palm oil for biofuels and oleochemicals, and harnessing Thailand's food technology capabilities to promote substitution in food production in favour of oils with healthier fatty acid composition.

Feasibility of microbially improved oil recovery (MIOR) in Northern German oil reservoirs; Bakterien zur Erhoehung des Entoelungsgrades in norddeutschen Erdoellagerstaetten

Energy Technology Data Exchange (ETDEWEB)

Amro, M. [Inst. fuer Erdoel- und Erdgasforschung, Clausthal-Zellerfeld (Germany); Kessel, D. [Inst. fuer Erdoel- und Erdgasforschung, Clausthal-Zellerfeld (Germany)

1996-05-01

The scope of this study was to investigate the feasibility of microbially improved oil recovery (MIOR) in Northern German oil reservoirs. Suitable bacterial strains had to be identified. The mechanisms for oil mobilization and incremental recovery had to be investigated. To this end, two independent methods were employed, namely static autoclave tests and dynamic flood experiments. The static tests were carried out without reservoir rock matrix to preselect suitable bacterial strains with a minimum of experimental effort. The selected strains were then tested in dynamic flood experiments under reservoir conditions on Bentheimer sandstone cores to quantify the oil recovery. Key results of the study are: (1) Two bacterial strains were found having excellent metabolic activity with potential for oil recovery under Northern German reservoir conditions. (2) These bacteria can be injected into and transported in the pores of the sandstone. (3) The metabolic activity of these bacteria leads to substantial incremental oil recovery in repeated injection - shut in - production cycles. (4) Incremental oil recovery is attributed to wettability change and biomass production by the metabolites of the bacteria. (orig.) [Deutsch] Das Ziel dieser Arbeit ist die Untersuchung der Anwendbarkeit der mikrobiell verbesserten Erdoelgewinnung in norddeutschen Lagerstaetten. Zunaechst waren hierfuer einsetzbare Bakterienstaemme zu identifizieren. Diese waren dann auf ihr Entoelungsvermoegen zu ueberpruefen. Schliesslich sollten die Entoelungsmechanismen ermittelt werden. Die Vorauswahl potentiell geeigneter Bakterienstaemme erfolgte durch verschiedene mikrobiologische Forschungsinstitute. Zur Minimierung des experimentellen Aufwands wurden diese Staemme dann im Institut fuer Erdoel- und Erdgasforschung in statischen Autoklavenversuchen unter Lagerstaettenbedingungen, jedoch noch ohne Lagerstaettengestein, auf ihre Stoffwechselaktivitaet sowie Art und Eigenschaften ihrer Stoffwechselprodukte

Co-Processing of Jatropha-Derived Bio-Oil with Petroleum Distillates over Mesoporous CoMo and NiMo Sulfide Catalysts

Directory of Open Access Journals (Sweden)

Shih-Yuan Chen

2018-02-01

Full Text Available The co-processing of an unconventional type of Jatropha bio-oil with petroleum distillates over mesoporous alumina-supported CoMo and NiMo sulfide catalysts (denoted CoMo/γ-Al2O3 and NiMo/γ-Al2O3 was studied. Either a stainless-steel high-pressure batch-type reactor or an up-flow fixed-bed reaction system was used under severe reaction conditions (330–350 °C and 5–7 MPa, similar to the conditions of the conventional diesel hydrodesulfurization (HDS process. To understand the catalytic performance of the mesoporous sulfide catalysts for co-processing, we prepared two series of oil feedstocks. First, model diesel oils, consisting of hydrocarbons and model molecules with various heteroatoms (sulfur, oxygen, and nitrogen were used for the study of the reaction mechanisms. Secondly, low-grade oil feedstocks, which were prepared by dissolving of an unconventional type of Jatropha bio-oil (ca. 10 wt % in the petroleum distillates, were used to study the practical application of the catalysts. Surface characterization by gas sorption, spectroscopy, and electron microscopy indicated that the CoMo/γ-Al2O3 sulfide catalyst, which has a larger number of acidic sites and coordinatively unsaturated sites (CUS on the mesoporous alumina framework, was associated with small Co-incorporated MoS2-like slabs with high stacking numbers and many active sites at the edges and corners. In contrast, the NiMo/γ-Al2O3 sulfide catalyst, which had a lower number of acidic sites and CUS on mesoporous alumina framework, was associated with large Ni-incorporated MoS2-like slabs with smaller stacking numbers, yielding more active sites at the brims and corresponding to high hydrogenation (HYD activity. Concerning the catalytic performance, the mesoporous CoMo/γ-Al2O3 sulfide catalyst with large CUS number was highly active for the conventional diesel HDS process; unfortunately, it was deactivated when oxygen- and nitrogen-containing model molecules or Jatropha bio-oil

Reception and treatment facilities for waste oils and oil-polluted waters from marine and industrial activities in Gothenburg, Sweden

International Nuclear Information System (INIS)

Andersson, K.; Lexen, S.I.; Hell, M.

1992-01-01

At the beginning of the 1980s, comprehensive solutions were found to problems associated with the handling of oil-polluted water from marine and industrial sources in the Gothenburg area. The treatment plant in the oil harbour has permission to treat 700,000 m 3 /yr of sludge, ballast, slops and other oil-contaminated waters. Following treatment by chemical flocculation, flotation and dual-media filtration, the treated water must not contain more than 5 ppm of oil. Work to improve treatment results has been carried out from the start, in close co-operation with environmental authorities and with the waste generators themselves. Through increased consciousness, improvements in control, and greater source separation, it will be possible to bring about a significantly lower concentration of pollutants in the incoming waste streams. Recent plans include separate treatment of waste streams containing aromatic compounds and heavily polluted waters. Complementary treatment methods, such as activated carbon and air stripping, are under evaluation. (author). 10 figs

Catalytic optimization and physicochemical studies over Zn/Ca/Al2O3 catalyst for transesterification of low grade cooking oil

International Nuclear Information System (INIS)

Mohd Kamal, Norhasyimah; Wan Abu Bakar, Wan Azelee; Ali, Rusmidah

2017-01-01

Highlights: • Zn/Ca/Al 2 O 3 has high potential in producing biodiesel. • High basicity favoured high conversion of biodiesel. • Calcination temperature showed the highest influence on the catalytic activity. • RSM was used to determine the optimum operating conditions for biodiesel production. - Abstract: Recently, there has been an increasing interest in green and renewable fuels due to the worldwide concern of an environmental crisis. So, this study focused on the synthesis, optimization and characterization of series of heterostructure Zn/Ca/Al 2 O 3 catalysts with different parameters to test their effectiveness towards biodiesel production. The physicochemical properties of the potential catalyst were determined by BET, FESEM and CO 2 -TPD. The activity of the catalyst in transesterification reaction was evaluated at reaction temperature of 65 °C, 3 h reaction time, 6% (w/w) catalyst concentration and 1:24 M ratio of oil to methanol. The investigation of the synthesized Zn/Ca/Al 2 O 3 catalyst showed that the calcination temperature, number of alumina coatings and dopant to base ratio have significant effects on the catalytic performance. These three critical parameters were investigated using response surface methodology (RSM) with Box Behnken design (BBD) to determine the optimum operating conditions for biodiesel production. From RSM study, the optimum conditions were 800 °C calcination temperature, 3 times alumina beads coating and 10:90 dopant to base ratio which gave 97.80% biodiesel conversion. From the F-value and low p-value (<0.05) obtained showed that the model was significant for predicting the optimum biodiesel conversion. An experiment was conducted under the optimum conditions to confirm the agreement of the model prediction and the experimental results. The experimental value (97.64%) closely agreed with the predicted results from RSM and hence validated the findings of response surface optimization.

Physicochemical properties of peanut oil-based diacylglycerol and their derived oil-in-water emulsions stabilized by sodium caseinate.

Science.gov (United States)

Long, Zhao; Zhao, Mouming; Liu, Ning; Liu, Daolin; Sun-Waterhouse, Dongxiao; Zhao, Qiangzhong

2015-10-01

High purity peanut oil-based diacylglycerol (PO-DAG) (94.95 wt%) was prepared via enzymatic glycerolysis from peanut oil (PO). The resulting dominance of DAGs was proven to greatly influence the properties of corresponding fresh or frozen-thawed emulsions. Stable fresh oil-in-water emulsions were produced using either PO-DAG or PO, with stability enhanced by increased concentrations of Na-CN. The lower equilibrium interfacial tension along with greater negative ζ-potential of PO revealed that Na-CN was preferentially adsorbed to the PO interface. Adding 0.05 mol/L NaCl to the PO emulsions minimized depletion flocculation caused by the unadsorbed Na-CN, but further NaCl addition increased oil droplet size and concomitant coalescence. For the PO-DAG emulsions, adding 0.2 mol/L NaCl did not significantly (p>0.05) affect their ζ-potential but adding 0.05 or 0.1 mol/L NaCl lowered ζ-potential, although NaCl at these concentrations increased oil droplet size and coalescence. Freezing-thawing process considerably weakened the stability of PO-DAG emulsions. Copyright © 2015 Elsevier Ltd. All rights reserved.

Polymer aids for settling and filtration of oil sands tailings

Energy Technology Data Exchange (ETDEWEB)

Wang, X. [Alberta Univ., Edmonton, AB (Canada). Dept. of Chemical and Materials Engineering; Energy Resources Conservation Board, Calgary, AB (Canada). Oil Sands Section; Xu, Z.; Masliyah, J.H. [Alberta Univ., Edmonton, AB (Canada). Dept. of Chemical and Materials Engineering

2008-07-01

Oil sand tailings are segregated into coarse and fine tailings. High volumes of toxic fluids and tailings are created in the process. Tailings ponds are an environmental risk with high operating and maintenance costs. Current commercial technologies uses chemical additions to create recycled water and composite tailings (CT). Researchers are now investigating centrifuged and dry mature fine tailings (MFT). Filtration processes with flocculants are used to separate the tailings into warm recycle water and dried cakes that can be used in reclamation processes. Studies are being conducted to find a polymer than can effectively flocculate and filter whole oil sands tailings. The filtration procedure uses pressure to produce released water. Polymers include magnafloc and Al-PAM polymer concentrations are used in slurry masses. Tests have been conducted to determine the settling rates of the polymers. The tests showed that Al-PAM filtered the tailings effectively. Paraffinic froth treatment tests have also been conducted to determine settling rates. A cake produced with froth treatment tailings of Al-PAM 400 ppm had a water content 42.5 wt per cent. The tests showed that while Magnafloc 1011 is a good settling aid, but a poor filtration addition. Al-PAM aided in both the flocculation and filtration processes. Higher Al-PAM dosages are needed for froth treatment tailings processes. It was concluded that dry cakes are produced with the addition of Al-PAM. tabs., figs.

NiCoCrAl/YSZ laminate composites fabricated by EB-PVD

International Nuclear Information System (INIS)

Shi Guodong; Wang Zhi; Liang Jun; Wu Zhanjun

2011-01-01

Highlights: → The metal-ceramic laminate composites were fabricated by EB-PVD. → Both metal and ceramic layers consisted of straight columns with banded structures. → Columnar grain size was limited by the periodic layer interfaces in the laminates. → Effect of columns on fracture property was decreased by limiting layer thickness. → Laminates showed greater specific strength than monolithic metal foil. - Abstract: Two NiCoCrAl/YSZ laminate composites (A and B) with different metal-layer thickness (∼35 μm and 14 μm, respectively) were fabricated by electron beam physical vapor deposition (EB-PVD). Their microstructure was examined and their mechanical properties were compared with the 289 μm thick NiCoCrAl monolithic foil produced by EB-PVD. Both the YSZ and NiCoCrAl layers of the laminate composites had columnar grain structure. But the periodic layer interfaces limited the columnar grain size. Some pores between the columns were also observed. It was found that the strength of the laminate A was equal approximately to that of the NiCoCrAl monolithic foil, and that laminate B had the greater strength. Moreover, the density of the foils decreased with the increasing thickness ratio of YSZ/NiCoCrAl layers and the increasing the layer number. Thus, comparing with the NiCoCrAl monolithic foil, the NiCoCrAl/YSZ laminate composites not only had the equal or greater strength, but also had the much greater specific strength.

Assessment of lubricating oil degradation in small motorcycle engine fueled with gasohol

Directory of Open Access Journals (Sweden)

Nakorn Tippayawong

2010-05-01

Full Text Available Assessment of the degradation of lubricating oil was performed on the lubricants which had been used in a small motorcycle engine fueled with gasohol in comparison with the lubricants from gasoline-run engine. The lubricant properties examined in the assessment were lubricating capacity, viscosity and stability to oxidation. Lubricating capacity was evaluated by accelerated wear test on the Timken tester. Lubricating oils from gasohol-run engine appeared to produce about 10% greater wear than that made in oils from gasoline-run engine. There was no significant difference between the effect of gasohol and gasoline on the viscosity of the used lubricating oils. Moreover, no oxidation products in any used oil samples could be detected.

Transcriptomic Analysis of the Effects of a Fish Oil Enriched Diet on Murine Brains

Science.gov (United States)

2014-03-14

Terra VC, de Almeida AC, et al. (2010) Qualitative analysis of hippocampal plastic changes in rats with epilepsy supplemented with oral omega-3 fatty... vegetable oil or fish oil. Am J Clin Nutr 63: 116–122. 92. Endres S, Meydani SN, Ghorbani R, Schindler R, Dinarello CA (1993) Dietary supplementation with

Antioxidant activity of rosemary essential oil fractions obtained by molecular distillation and their effect on oxidative stability of sunflower oil.

Science.gov (United States)

Mezza, Gabriela N; Borgarello, Ana V; Grosso, Nelson R; Fernandez, Héctor; Pramparo, María C; Gayol, María F

2018-03-01

The objective of this study was to evaluate the antioxidant activity of rosemary essential oil fractions obtained by molecular distillation (MD) and investigate their effect on the oxidative stability of sunflower oil. MD fractions were prepared in a series of low-pressure stages where rosemary essential oil was the first feed. Subsequently, a distillate (D1) and residue (R1) were obtained and the residue fraction from the previous stage used as the feed for the next. The residue fractions had the largest capacity to capture free radicals, and the lowest peroxide values, conjugated dienes and conjugated trienes. The antioxidant activity of the fractions was due to oxygenated monoterpenes, specifically α-terpineol and cis-sabinene hydrate. Oxidative stability results showed the residues (R1 and R4) and butylated hydroxytoluene had greater antioxidant activity than either the distillate fractions or original rosemary essential oil. The residue fractions obtained by short path MD of rosemary essential oil could be used as a natural antioxidants by the food industry. Copyright © 2017. Published by Elsevier Ltd.

Hydroprocessing of rubber seed oil to renewable fuels

Science.gov (United States)

Tran, Tan Viet; Phung, Minh Tri

2017-09-01

Hydroprocessing of rubber seed oil (RSO) with various types of alumina-silica support catalyst was conducted at 400°C and a hydrogen partial pressure of 3.0 MPa in 3 hours. The effects of the alumina-silica and metal doping on alumina-silica on the conversion, and distribution of oil fraction products (initial boiling point (IBP) to 80°C, from 80-200°C, from 200-360°C and higher than 360°C boiling point) were investigated. Compared to the results obtained when using Mo@Al2O3-SiO2, hydroprocessing of RSO resulted in a higher conversion and much higher yield of the light fraction (BP <230°C). Both alumina-silica catalysts led to an improved conversion as well as a higher light fraction yield. Results show that hydroprocessing of RSO with metal doping on alumina-silica support was more efficient than that only Al2O3-SiO2.

Quality and Chemical Composition of Organic and Non-Organic Vetiver Oil

Directory of Open Access Journals (Sweden)

Asep Kadarohman

2014-03-01

Full Text Available Vetiver oil (Vetiveria zizanoides has been used as perfume materials, cosmetics, fragrance soaps, anti-inflammation, repellent, and insecticidal agents. Organic vetiver oil has higher economical value than non-organic vetiver oil and it has been regarded to be able to compete in the global market. Therefore, studies have been carried out using 1 hectare of land and the first generation of organic vetiver oil has produced 0.57% of yield, greater than non-organic (0.50%. The quality of organic and non-organic vetiver oil was analyzed by Indonesian Standard (SNI parameter, pesticide residue test, chemical composition by GC/MS, and the appearance of vetiver root. In general, the result of organic and non-organic vetiver oil has fulfilled the national standard; the quality of organic vetiver oil was better than non-organic one. Physically, the appearance of organic vetiver root was better than non-organic vetiver root; organic vetiver root was denser, more appealing, and did not have any black spots. The pesticide residue of organic vetiver oil was lower than non-organic vetiver oil. Based on SNI test, vetiverol (oxygen compounds in organic vetiver oil was higher than non-organic vetiver oil.

Determination of metallo-organic and particulate wear metals in lubricating oils associated with hybrid ceramic bearings by inductively coupled plasma mass spectrometry

Science.gov (United States)

Russell, Robin Ann

It is possible to increase both the performance and operating environment of jet engines by using hybrid ceramic bearings. Our laboratory is concerned with investigating lubricating fluids for wear metals associated with silicon nitride ball bearings and steel raceways. Silicon nitride is characterized by low weight, low thermal expansion, high strength, and corrosion resistance. These attributes result in longer engine lifetimes than when metallic ball bearings are used. Before the routine use of ceramic ball bearings can be realized, the wear mechanisms of the materials should be thoroughly understood. One important variable in determining wear degradation is the concentration of metal present in the lubricating oils used with the bearings. A complete method for analyzing used lubricating oils for wear metal content must accurately determine all metal forms present. Oil samples pose problems for routine analysis due to complex organic matrices. Nebulizing these types of samples into an Inductively Coupled Plasma - Mass Spectrometer introduces many problems including clogging of the sample cone with carbon and increasing interferences. In addition, other techniques such as Atomic Absorption Spectrometry and Atomic Emission Spectrometry are particle size dependent. They are unable to analyze particles greater than 10 mum in size. This dissertation describes a method of analyzing lubricating oils for both metallo-organic and particulate species by ICP-MS. Microwave digestion of the oil samples eliminates the need for elaborate sample introduction schemes as well as the use of a modified carrier gas. Al, Cr, Fe, Mg, Mo, Ni, Ti, and Y have been determined in both aqueous and organic media. Metallo-organic solutions of these metals were successfully digested, nebulized into the ICP, and the singly charged ions measured by mass spectrometry. Metal particulates in oil matrices have also been quantitatively determined by the above method. Linear analytical curves were

Technical and economic framework for market enhancement of shale oil

International Nuclear Information System (INIS)

Bunger, J.W.; Devineni, A.V.

1992-01-01

By now it is apparent that production of syncrude from shale oil will not be economically viable as long as there is a stable and reasonably-priced supply of petroleum. The costs and financial risks of producing syncrude from oil shale, in the face of price constraints imposed by petroleum markets, are too high to warrant private investment. A possible solution is to develop commodity and specialty products from shale oil which command a high market value. In this fashion, the economics are partially uncoupled from petroleum and an opportunity for a greater price/cost differential is provided

Exotic Vegetable Oils for Cosmetic O/W Nanoemulsions: In Vivo Evaluation

OpenAIRE

Tatiana A. Pereira; Carolina M. Guerreiro; Monica Maruno; Marcio Ferrari; Pedro Alves Rocha-Filho

2016-01-01

Oil-in-water nanoemulsions are stable systems with droplet sizes in the 20–200 nm range. The physicochemical properties of these systems may be influenced by the addition of additives. Thus, the influence of ethoxylated (EL) and acetylated lanolin (AL) addition on the droplet size, pH values, electrical conductivity and stability of nanoemulsions was investigated. Then, effect of nano-emulsions additives with EL (NE-EL) or AL (NE-AL) in hydration, oiliness and pH of the skin were evaluated. N...

PHYSICOCHEMICAL AND RHEOLOGICAL CHARACTERIZATION OF AVOCADO OILS

Directory of Open Access Journals (Sweden)

Tamara de Souza Jorge

2015-08-01

Full Text Available Avocado oil is rich in bioactive compounds, which can improve human health by acting as an antioxidant. It may be extracted from different varieties of avocado, such as Margarida and Hass varieties, each of them with particular characteristics. Aiming to evaluate the differences between them, avocado fruits and pulps from these were analyzed according to their physicochemical characteristics. After extracted, the oils had their bioactive characteristics studied and rheological behavior determined through a rotational rheometer. They were then compared to commercial avocado oil. The fruits of Margarida variety had greater size, higher weight (664.51 g, and higher pulp yield (72.19% than Hass variety, which showed higher lipid content (65.29 g/100 g dry basis. The commercial oil showed less primary oxidative degradation, whereas Margarida variety had a lower level of secondary degradation products as well as a higher content of bioactive compounds, such as phytosterols (999.60 mg/kg and tocopherols (36.73 mg/kg. The rheological behaviors of both oils were appropriately described through Newton model, with R2 > 0.999 for all temperatures. By an Arrhenius type equation, it was verified that Hass's rheological parameters are more influenced by temperature than Margarida and commercial oil, presenting activation energy of 33.6 kJ/mol.

Permeability response of oil-contaminated compacted clays

International Nuclear Information System (INIS)

Silvestri, V.; Mikhail, N.; Soulie, M.

1997-01-01

This paper presents the results of a laboratory investigation on the behavior of motor oil-contaminated, partially saturated compacted clays. For the study, both a natural clay and an artificially purified kaolinite, contaminated with 0 to 8% of motor oil, were firstly compacted following the ASTM standard procedure. Secondly, permeability tests were carried out in a triaxial cell on 10 cm-diameter compacted clay specimens. The results of the investigation indicate that increasing percentages of motor oil decrease both the optimum water content and the optimum dry density of the two clays. However, whereas the optimum water content on the average decreases by about 6% when the percentage contamination increases from 0 to 8%, the corresponding decrease in the optimum dry density is less than 3%. Even though the optimum dry density decreases as the percentage of oil increases from 0 to 8%, there is, however, a range in oil content varying between 2 and 4% for which the optimum dry density is slightly greater than that of the untreated soils. As far as the permeability tests are concerned, the results indicate that as the percentage of oil increases, the coefficient of permeability decreases substantially, especially for clay specimens which were initially compacted on the dry side of optimum

Soybean oil and linseed oil supplementation affect profiles of ruminal microorganisms in dairy cows.

Science.gov (United States)

Yang, S L; Bu, D P; Wang, J Q; Hu, Z Y; Li, D; Wei, H Y; Zhou, L Y; Loor, J J

2009-11-01

The objective of this study was to evaluate changes in ruminal microorganisms and fermentation parameters due to dietary supplementation of soybean and linseed oil alone or in combination. Four dietary treatments were tested in a Latin square designed experiment using four primiparous rumen-cannulated dairy cows. Treatments were control (C, 60 : 40 forage to concentrate) or C with 4% soybean oil (S), 4% linseed oil (L) or 2% soybean oil plus 2% linseed oil (SL) in a 4 × 4 Latin square with four periods of 21 days. Forage and concentrate mixtures were fed at 0800 and 2000 h daily. Ruminal fluid was collected every 2 h over a 12-h period on day 19 of each experimental period and pH was measured immediately. Samples were prepared for analyses of concentrations of volatile fatty acids (VFA) by GLC and ammonia. Counts of total and individual bacterial groups (cellulolytic, proteolytic, amylolytic bacteria and total viable bacteria) were performed using the roll-tube technique, and protozoa counts were measured via microscopy in ruminal fluid collected at 0, 4 and 8 h after the morning feeding. Content of ruminal digesta was obtained via the rumen cannula before the morning feeding and used immediately for DNA extraction and quantity of specific bacterial species was obtained using real- time PCR. Ruminal pH did not differ but total VFA (110 v. 105 mmol/l) were lower (P ruminal NH3-N (4.4 v. 5.6 mmol/l) was greater (P ruminal fluid was substantially lower (P ruminal microorganisms, except proteolytic bacteria, are highly susceptible to dietary unsaturated fatty acids supplementation, particularly when linolenic acid rich oils were fed. Dietary oil effects on ruminal fermentation parameters seemed associated with the profile of ruminal microorganisms.

Conformation evolution of oil contaminants onto aluminum oxide surface in aqueous solution: The effect of surface coverage

Energy Technology Data Exchange (ETDEWEB)

Xie, Wenkun; Liu, Haitao, E-mail: xwk584523412@126.com; Sun, Yazhou; Fu, Hongya; Liang, Yingchun

2017-01-15

Highlights: • The dynamic conformational change of oil contaminations, at various surface coverages onto perfect α-Al{sub 2}O{sub 3}(0001) surface in aqueous solution is given. • The effect of surface coverage of oil molecules on the driving forces for the conformational change of oil contaminations is described. • The effect of interfacial water on the conformational change and even detachment of oil contaminations is considered. - Abstract: The microscopic conformational change process of oil contaminants adhered onto perfect α-Al{sub 2}O{sub 3} (0001) surface in aqueous solution was investigated by using all-atom classic molecular dynamics simulations. The change in removal mechanism of oil contaminants induced by surface coverage (surface area per molecule) was emphatically explored. Our simulation results strongly reveal that the increase in oil surface coverage induces an evident difference in microscopic detachment processes of oil contaminants. At a low surface coverage, oil contaminants can be thoroughly detached from solid surface. The whole detachment process could be divided into multi stages, including conformational change of oil contaminants on solid surface, dynamic motion of those in bulk solution and rapid migration of those from bulk solution to air/water interface. With surface coverage increasing, water diffusion becomes the key to induce conformational change and promote the detachment of oil contaminants. When oil surface coverage exceeds a threshold value, oil contaminants also undertake an evident conformational change process exhibiting typical characteristics but an incomplete detachment process occurs. All findings of the present study are helpful for the interpretation of the removal mechanism of oil contaminants on solid surface.

The Effect of Dietary Oils on Growth Performance of Broilers ...

African Journals Online (AJOL)

a

chicks/group) and fed diets supplemented with 0.5% sunflower oil (Group A), ... improve performance and to decrease indices of inflammatory response in the ... protein synthesis and accretion in the skeletal muscle (Hentges et al., 1984).

The effect of degumming by hydration on the purification of high acidity solvent extracted olive oil

Directory of Open Access Journals (Sweden)

Thomopoulos, C. D.

1993-10-01

Full Text Available The degumming result of the following factors was studied: the temperature of hydration, the percentage of water in oil and the contact time at the hydration temperature. The hydration at 95°C with 2% water for a contact time of 15 min resulted in maximum removal of phosphorus of the oil with minimum oil losses. The same purification result was also attained at 80°G with 2% water and for a contact time of 15 min causing 2.19% greater losses of the oil. Under these conditions the hydration resulted in an about 35-48% removal of the phosphorus in crude oil. The residual phosphorus was removed by subsequent alkali neutralization.

El resultado del desgomado, controlado por la disminución del contenido en fósforo, fue estudiado según los siguientes factores: temperatura de hidratación, porcentaje de agua en el aceite y tiempo de contacto a la temperatura de hidratación. La hidratación a 95°C con 2% de agua y tiempo de contacto de 15 minutos, dio la máxima eliminación del contenido en fósforo del aceite crudo y el mínimo de pérdidas en aceite. Cambiando la temperatura de 95 a 80°C y manteniendo el contenido en agua al 2% y el tiempo de contacto de 15 minutos, aumentó la pérdida de aceite en un 2.19%. Bajo estas condiciones, y en ambos casos, se consiguió eliminar el 35-48% del contenido en fósforo del aceite crudo, eliminándose el residual mediante la neutralización alcalina.

Long-term storage of three unconventional oils

Directory of Open Access Journals (Sweden)

Hussein, Ismail H.

2008-03-01

Full Text Available Three samples, Sclerocarya birrea oil (SCO, Melon bug oil (Aspongubus viduatus (MBO, and Sorghum bug oil (Agonoscelis pubescens (SBO, were stored (autoxidized in the dark at 30±2 °C for 24 months. Oil aliquots were withdrawn every 2-4 month for analyses of changes in four quality indexes, namely fatty acid composition, tocopherol content, peroxide value and oxidative stability index by Rancimat. After 24 months of storage the fatty acid composition of the three oils showed no change while tocopherol contents were decreased. SCO and MBO showed only slight changes in their oxidative stability as indicated by the peroxide value and induction period during the 24 months of storage. Sorghum bug oil showed a periodical increase in the peroxide value and had less stability as measured by the Rancimat in comparison to other oils.Tres muestras de aceite, Sclerocarya birrea oil (SCO, Melon bug oil (Aspongubus viduatus (MBO, and Sorghum bug oil (Agonoscelis pubescens (SBO, fueron almacenadas en la oscuridad a 30±2 °C durante 24 meses. Cada 2- 4 meses se toman alícuotas para analizar los cambios de calidad. Se determinaron la composición en ácidos grasos, el contenido en tocoferol, el índice de peróxidos y la estabilidad oxidativa mediante el aparato Rancimat. Después de 24 meses de almacenamiento, la composición en ácidos grasos no experimentó variación mientras que el contenido en tocoferol disminuyó en los tres aceites. SCO y MBO mostraron cambios minoritarios como se comprobó por los indices de peroxides y estabilidad a los 24 meses. SBO fue el menos estable de los tres aceites.

Predicting Greater Prairie-Chicken Lek Site Suitability to Inform Conservation Actions.

Directory of Open Access Journals (Sweden)

Torre J Hovick

Full Text Available The demands of a growing human population dictates that expansion of energy infrastructure, roads, and other development frequently takes place in native rangelands. Particularly, transmission lines and roads commonly divide rural landscapes and increase fragmentation. This has direct and indirect consequences on native wildlife that can be mitigated through thoughtful planning and proactive approaches to identifying areas of high conservation priority. We used nine years (2003-2011 of Greater Prairie-Chicken (Tympanuchus cupido lek locations totaling 870 unique leks sites in Kansas and seven geographic information system (GIS layers describing land cover, topography, and anthropogenic structures to model habitat suitability across the state. The models obtained had low omission rates (0.81, indicating high model performance and reliability of predicted habitat suitability for Greater Prairie-Chickens. We found that elevation was the most influential in predicting lek locations, contributing three times more predictive power than any other variable. However, models were improved by the addition of land cover and anthropogenic features (transmission lines, roads, and oil and gas structures. Overall, our analysis provides a hierarchal understanding of Greater Prairie-Chicken habitat suitability that is broadly based on geomorphological features followed by land cover suitability. We found that when land features and vegetation cover are suitable for Greater Prairie-Chickens, fragmentation by anthropogenic sources such as roadways and transmission lines are a concern. Therefore, it is our recommendation that future human development in Kansas avoid areas that our models identified as highly suitable for Greater Prairie-Chickens and focus development on land cover types that are of lower conservation concern.

Canadian oil and gas survey : 1997

International Nuclear Information System (INIS)

Roberge, R.B.

1997-01-01

An outlook of the Canadian Petroleum Industry, financial and operating statistics of the top 100 Canadian public oil and gas companies and 15 energy income trusts, were summarized for the fiscal year ending in 1996. In general, 1996 was a good year for the industry. Greater industry financing resulted in increased drilling activity and good stock market returns for investors. However, strong commodity prices also resulted in record levels of hedging activity, which meant lost revenues for the industry. The top 100 companies recorded losses of about $800 million in 1996, largely on crude oil hedges. The fact that volumes hedged forward to 1997 are down from 1996 indicate that many companies are rethinking their commitment to risk management. Details of crude oil and natural gas prices and production levels during 1996 were provided. A list of significant corporate mergers and acquisitions during the year under review rounded out the presentation

Oil and Labour: The Pivotal Position of Persian Oil in The First World War and the Question of Transnational Labour Dependency

NARCIS (Netherlands)

Atabaki, T.; De Vito, Christian G.; Gerritsen, Anne

2017-01-01

Atabaki examines the conceptualization, articulation, and implementation of the Oil Company’s shifting labour policy against the background of greater global geopolitical shifts during the First World War. The chapter especially addresses the spatiality of labour recruitment across the Persian

Spatial heterogeneity in response of male greater sage-grouse lek attendance to energy development.

Directory of Open Access Journals (Sweden)

Andrew J Gregory

Full Text Available Landscape modification due to rapidly expanding energy development, in particular oil and gas, in the westernUSA, have prompted concerns over how such developments may impact wildlife. One species of conservation concern across much of the Intermountain West is the greater sage-grouse (Centrocercusurophasianus. Sage-grouse have been petitioned for listing under provisions of the Endangered Species Act 7 times and the state of Wyoming alone represents 64% of the extant sage-grouse population in the eastern portion of their range. Consequently, the relationship between sage-grouse populations and oil and gas development in Wyoming is an important component to managing the long-term viability of this species. We used 814 leks from the Wyoming Game and Fish Department's lek survey database and well pad data from the Wyoming Oil and Gas Conservation Commission to evaluate changes in sage-grouse lek counts as a function of oil and gas development since 1991.From 1991-2011 we found that oil and gas well-pad density increased 3.6-fold across the state and was associated with a 24% decline in the number of male sage-grouse. Using a spatial and temporally structured analysis via Geographically Weighted Regression, we found a 1-to-4 year time lag between development density and lek decline. Sage-grouse also responded to development densities at multiple spatial neighborhoods surrounding leks, including broad scales of 10 km. However, sage-grouse lek counts do not always decline as a result of oil and gas development. We found similar development densities resulting in different sage-grouse lek count responses, suggesting that development density alone is insufficient to predict the impacts that oil and gas development have on sage-grouse. Finally, our analysis suggests a maximum development density of 1 well-pad within 2 km of leks to avoid measurable impacts within 1 year, and <6 well-pads within 10 km of leks to avoid delayed impacts.

Gas and Oil Flow through Wellbore Flaws

Science.gov (United States)

Hatambeigi, M.; Anwar, I.; Reda Taha, M.; Bettin, G.; Chojnicki, K. N.; Stormont, J.

2017-12-01

We have measured gas and oil flow through laboratory samples that represent two important potential flow paths in wellbores associated with the Strategic Petroleum Reserve (SPR): cement-steel interfaces (microannuli) and cement fractures. Cement fractures were created by tensile splitting of cement cores. Samples to represent microannuli were created by placing thin steel sheets within split cement cores so flow is channeled along the cement-steel interface. The test sequence included alternating gas and oil flow measurements. The test fluids were nitrogen and silicone oil with properties similar to a typical crude oil stored in the SPR. After correcting for non-linear (inertial) flow when necessary, flows were interpreted as effective permeability and hydraulic aperture using the cubic law. For both samples with cement fractures and those with cement-steel interfaces, initial gas and oil permeabilities were comparable. Once saturated with oil, a displacement pressure had to be overcome to establish gas flow through a sample, and the subsequent gas permeability were reduced by more than 50% compared to its initial value. Keywords: wellbore integrity, leakage, fracture, microannulus, SPR. Sandia National Laboratories is a multi-mission laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of NTESS/Honeywell, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000. SAND2017-8168 A

Comparison of pigeon guillemot, Cepphus columba, blood parameters from oiled and unoiled areas of Alaska eight years after the Exxon Valdez oil spill

Science.gov (United States)

Seiser, P.E.; Duffy, L.K.; McGuire, David A.; Roby, D.D.; Golet, Gregory H.; Litzow, Michael A.

2000-01-01

In 1997, we compared the haematological and plasma biochemical profiles among populations of pigeon guillemots, Cepphus columba, in areas oiled and not oiled by the 1989 Exxon Valdez oil spill (EVOS) that occurred in Prince William Sound (PWS), Alaska. Pigeon guillemot populations in PWS were injured by EVOS and have not returned to pre-spill levels. If oil contamination is limiting recovery of pigeon guillemots in PWS, then we expected that blood parameters of pigeon guillemots would differ between oiled and unoiled areas and that these differences would be consistent with either toxic responses or lower fitness. We collected blood samples from chicks at approximately 20 and 30 days after hatching. Physiological changes associated with chick growth were noted in several blood parameters. We found that only calcium and mean cell volume were significantly different between the chicks in oiled and unoiled areas. Despite these differences, blood biomarkers provided little evidence of continuing oil injury to pigeon guillemot chicks, eight years after the EVOS. Preliminary data from adults indicated elevated aspartate aminotransferase activity in the adults from the oiled area, which is consistent with hepatocellular injury. Because adults have greater opportunities for exposure to residual oil than nestlings, we recommend studies that fully evaluate the health of adults residing in oiled areas. (C) 2000 Elsevier Science Ltd.

Comparative studies of antifugal potentialities for some natural plant oils against different fungi isolated from poultry

Directory of Open Access Journals (Sweden)

Ahmed, F. H.

1994-08-01

Full Text Available The inhibitory effect of eight natural oils on ten pathogenic fungi isolated from the digestive and respiratory tracts of dead chickens in Kena Governorate showed that crude peppermint oil only has a highest effect against some isolated fungi and a low response against others. While its 10% and 2% oil concentrations failed to give any effect against all the tested fungi. Crude chamomile and pelargonium oils showed moderate effect against all isolated fungi. The effect of different dilutions of chamomile, cumin and celery oils appeared that the 10% concentration showed more effective than the crude oil. Lemongrass and basil oils have almost the same behaviour towards the isolated fungi as the crude oils and the 10% concentration affected them greatly. On the other hand 2% basil oil gave no effect at all. Critical concentrations of the efficient oils against isolated fungi were calculated. The most efficient oils were lemongrass against Aspergillus flavipes, chamomile against A. fumigatus and cumin against A. nidulans, while cumin against A. glaucus, clove against A. flavus were chamomile against A. flavus and clove against A. flavipes were the lowest efficient oils.

El efecto inhibidor de ocho aceites naturales sobre diez aislados de hongos patógenos de los tractos digestivo y respiratorio de pollos muertos en "Kena Governorate" mostró que el aceite de menta crudo tiene un mayor efecto frente a algunos aislados y una repuesta menor frente a otros. Aunque sus concentraciones en aceite al 10% y 2% consiguieron dar algún efecto frente a todos los hongos ensayados. Aceites de geranio y manzanilla crudo mostraron efecto moderado frente a todos los aislados de hongos. El efecto de disoluciones diferentes de aceites de manzanilla, comino y apio dieron como resultado que la concentración al 10% era más efectiva que el aceite crudo. Aceites de lemongras y albahaca tienen casi el mismo

The solution of the problem of oil spill risk control in the Baltic Sea taking into account the processes of oil propagation and degradation

Science.gov (United States)

Aseev, Nikita; Agoshkov, Valery

2015-04-01

The report is devoted to the one approach to the problem of oil spill risk control of protected areas in the Baltic Sea (Aseev et al., 2014). By the problem of risk control is meant a problem of determination of optimal resources quantity which are necessary for decreasing the risk to some acceptable value. It is supposed that only moment of accident is a random variable. Mass of oil slick is chosen as a function of control. For the realization of the random variable the quadratic 'functional of cost' is introduced. It comprises cleaning costs and deviation of damage of oil pollution from its acceptable value. The problem of minimization of this functional is solved based on the methods of optimal control and the theory of adjoint equations (Agoshkov, 2003, Agoshkov et al., 2012). The solution of this problem is explicitly found. In order to solve the realistic problem of oil spill risk control in the Baltic Sea the 2d model of oil spill propagation on the sea surface based on the Seatrack Web model (Liungman, Mattson, 2011) is developed. The model takes into account such processes as oil transportation by sea currents and wind, turbulent diffusion, spreading, evaporation from sea surface, dispersion and formation of emulsion 'water-in-oil'. The model allows to calculate basic oil slick parameters: localization, mass, volume, thickness, density of oil, water content and viscosity of emulsion. The results of several numerical experiments in the Baltic Sea using the model and the methodology of oil spill risk control are presented. Along with moment of accident other parameters of oil spill and environment could be chosen as a random variables. The methodology of solution of oil spill risk control problem will remain the same but the computational complexity will increase. Conversion of the function of control to quantity of resources with a glance to methods of pollution removal should be processed. As a result, the developed 2d model of oil spill propagation

Flood offers new hope for marginal oil fields

Energy Technology Data Exchange (ETDEWEB)

1966-03-14

The economics of producing a marginal Cardium sand oil field in west-central Alberta have been greatly improved by introduction of an inexpensive waterflood pressure maintenance and secondary recovery project. Canadian Gridoil Ltd. is now in full operation at its Willesden Green Cardium Unit No. 5. Of the 8.1 million bbl estimated original oil in place, only 9% would have been recoverable by primary depletion. The waterflood is calculated to add 13%, for ultimate recovery of 22% or 1.8 million bbl. This waterflood installation is considered a prototype of economical and profitable pressure maintenance systems which can be built to advantage in marginal oil fields in Alberta. Ultimate returns in the form of increased oil production and more than doubled oil recovery will be immensely greater than the capital investment of $195,000 in the facilities. Assuming GOR control and full well allowables, the entire capital cost should be paid out within 3 years. Life of the field is estimated at not less than 25 years.

New technology for sulfide reductions and increased oil recovery: Petroleum project fact sheet

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-12-14

This Fact Sheet is written for the Inventions and Innovations Program about a new technology for sulfide reduction and increased oil recovery. The new technology, called Bio-Competitive Exclusion (BCX), results in greater oil production and prevents the production of corrosive hydrogen sulfide in oil and gas reservoirs. This BCX process is initiated and maintained by a new product, called Max-Well 2000, in which nutrients are custom designed to stimulate targeted beneficial microorganisms that live in every oil and gas reservoir. Rapid growth of these microorganisms excludes activity of harmful sulfide-producing bacteria and produces by-products that serve as effective tertiary oil recovery agents and as sulfide degradation agents. Oil and gas production is both increased and sweetened.

The role of transnational companies as oil suppliers to the United States

International Nuclear Information System (INIS)

Palazuelos, Enrique

2010-01-01

This paper analyzes the extent to which the international oil production of transnational companies meets the oil requirements of the United States. Disaggregated data from each company have been used to determine which companies (refineries) are importing crude oil, how much oil each transnational company is produced abroad, and where this production goes to. The analysis show that American international oil production represents a small part of U.S. oil imports. Two conclusions are reached. The first is that U.S. refineries buy the majority of the crude oil they process on the international market and, as a result, are dependent on the unstable conditions of this market. The second is that the economic interests the large American oil companies have abroad are far greater than those they have within the United States and, as a result, these companies do not play a decisive role in a national strategy to guarantee foreign supply.

Volatile oil profile of some lamiaceous plants growing in Saudi Arabia and their biological activities.

Science.gov (United States)

Ibrahim, Sabrin R M; Abdallah, Hossam M; Mohamed, Gamal A; Farag, Mohamed A; Alshali, Khalid Z; Alsherif, Emad A; Ross, Samir A

2017-01-01

A comparative investigation of hydro-distilled essential oils from aerial parts of Mentha longifolia L. (ML), Mentha microphylla K.Koch (MM), Mentha australis R.Br. (MA), and Teucrium polium L. (TP) growing in Al Madinah Al Munawwarah, Saudi Arabia, was carried out. The total numbers of identified constituents were 22, 23, 14, and 20 in ML, MM, MA, and TP oils, representing 93.0, 99.3, 78.1, and 81.1% of the total oil composition, respectively. Pulegone (40.7%) and cineole (33.4%) were the major components in ML, whereas carvone (64.6%) was the major one in MM. Furthermore, β-linalool (22.9%) and α-terpineol (12%) were the major components in MA, whereas, (E)-3-caren-2-ol accounted for 12.1% in TP. The essential oils of TP and MA exhibited promising activities against Leishmania donovani promastigotes with IC50 values of 2.3 and 3.7 μg/mL, respectively. In contrast, MA essential oils exhibited antifungal activities towards Candida krusei and C. glabrata with IC50 values of 1 and 1.2 μg/mL, respectively.

Use of biomass sorbents for oil removal from gas station runoff.

Science.gov (United States)

Khan, Eakalak; Virojnagud, Wanpen; Ratpukdi, Thunyalux

2004-11-01

The use of biomass sorbents, which are less expensive and more biodegradable than synthetic sorbents, for oil removal from gas station runoff was investigated. A bench-scale flume experiment was conducted to evaluate the oil removal and retention capabilities of the biomass sorbents which included kapok fiber, cattail fiber, Salvinia sp., wood chip, rice husk, coconut husk, and bagasse. Polyester fiber, a commercial synthetic sorbent, was also experimented for comparison purpose. Oil sorption and desorption tests were performed at a water flow rate of 20 lmin-1. In the oil sorption tests, a 50 mgl(-1) of used engine oil-water mixture was synthesized to simulate the gas station runoff. The mass of oil sorbed for all sorbents, except coconut husk and bagasse, was greater than 70%. Cattail fiber and polyester fiber were the sorbents that provided the least average effluent oil concentrations. Oil selectivity (hydrophobic properties) and physical characteristics of the sorbents are the two main factors that influence the oil sorption capability. The used sorbents from the sorption tests were employed in the desorption tests. Results indicated that oil leached out of all the sorbents tested. Polyester fiber released the highest amount of oil, approximately 4% (mass basis) of the oil sorbed. copyright 2004 Elsevier Ltd.

Extraction and analysis of tea (Camellia sinensis) seed oil from ...

African Journals Online (AJOL)

OMONDI-GUYA

2013-02-20

Feb 20, 2013 ... spectrophotometer (Model JENWAY6705, multi-cell changer) against a blank ... All the tea seed oil extracts were golden yellow in color and liquid at .... respectively, the two being products of oxidative rancidity. (Chindo et al.

Operation variables in transesterification of vegetable oil: an enzymatic catalysis review

Directory of Open Access Journals (Sweden)

Andrés Felipe Rojas González

2010-01-01

Full Text Available This paper presents the results of a literature review regarding how operating conditions influence vegetable oil enzymatic transesterification yield. The following parameters were studied: temperature and time reaction, alcohol: oil molar ratio, alcohol type, biocatalyst type and concentration, solvent, mixed intensity, reagent purity and free fatty acid and moisture concentration. Yields greater than 90% can be achieved in the enzymatic catalyst of vegetable oil using 35-50°C temperatures, long time reactions (7- 90h and a 3:1alcohol: vegetable oil molar ratio; however, such values would intrinsically depend on the type of lipase and oil u- sed. It was also found that free fatty acid and moisture concentration were parameters which did not require rigorous control due to high enzyme specificity. Lipases immobilised from Pseudomona cepacia bacteria and Rhizopus orizae fungi were most used in vegetable oil enzymatic transesterification.

Corruption and reduced oil production: An additional resource curse factor?

International Nuclear Information System (INIS)

Al-Kasim, Farouk; Søreide, Tina; Williams, Aled

2013-01-01

Prominent contributions to the resource curse literature suggest weak governance and corruption are important factors behind the wide welfare variations observed among oil producing countries. How weak governance and corruption influence revenue management and expenditure decisions, as well as the possible welfare benefits derived from oil, are broadly discussed. How they impact upon volumes of oil produced has, however, attracted little attention. This paper combines a review of the resource curse and oil production literatures with findings from qualitative interviews with oil sector experts to appreciate the feasibility of connections between corruption and oil production below its potential. We make particular reference to environments where regulatory institutions or political accountability are weak and focus primarily on producer government and oil firm relations. Drawing on insights from geology, political science and economics, we suggest suboptimal production solutions can impact volumes of oil actually produced and create constraints on long term revenues for oil producing countries. We argue greater disclosure of information on oil production efficiency on a field-by-field and country-by-country basis will assist further investigation of the relationships between corruption and volumes of oil produced. - Highlights: ► We combine a literature review with qualitative interviews with oil experts. ► We focus on feasible connections between corruption and oil production levels. ► We suggest suboptimal production solutions can impact volumes of oil produced. ► Corruption may reinforce suboptimal oil production. ► More data on oil production efficiency by field and country will assist research

Determination of levels of polychlorinated biphenyl in transformers oil from some selected transformers in parts of the Greater Accra Region of Ghana.

Science.gov (United States)

Buah-Kwofie, Archibold; Yeboah, Philip O; Pwamang, John

2011-01-01

Although polychlorinated biphenyls have never been manufactured in Ghana, it has been used extensively as dielectric fluid in electric transformers and capacitors. However, very little is known of its health and environmental impacts by both managers of these transformers and capacitors and also the general public. This work therefore seeks to explore INAA as a possible alternative to screening transformer oils for PCBs by determining the total chlorine content. The total chlorine content of transformer oil samples from Ghana that tested positive and some randomly selected samples that tested negative from screening using CLOR-N-OIL test kits, have had their total chlorine estimated. INAA using the Research Reactor located at the Ghana Atomic Energy Commission was used to estimate the total chlorine content of the oil samples. Neutron Activation and gamma ray spectroscopy using HPGe detector coupled to MAESTRO 32 software was used to determine the total chlorine content by integrating the peak area of the spectrum into a simplified program that was developed from the activation equation. Instrumental Neutron Activation Analysis was able to validate the result obtained from the test kits screening with accuracy 7.5%. The minimum total chlorine content of the positive samples determined by NAA was 71.34 μg g⁻¹. Copyright © 2010 Elsevier Ltd. All rights reserved.

Performance assessment of the catalyst ZnAl2O4 and Cu/ZnAl2O4 esterification reaction fatty acid in biodiesel

International Nuclear Information System (INIS)

Feitosa, A.C.; Dantas, J.; Costa, A.C.M.F.; Barbosa, D.C.; Meneghetti, S.M.P.

2012-01-01

This study aims to evaluate the performance of the Cu/ZnAl 2 O 4 and ZnAl 2 O 4 methyl esterification of fatty acids of soybean oil into biodiesel. The ZnAl 2 O 4 was synthesized by combustion reaction and then the sample was wet impregnated with a copper source. The samples were characterized by XRD, SEM, textural analysis and catalytic tests bench. The characterization results showed that the samples showed characteristic diffraction peaks spinel, with the characteristic of mesoporous material (10-250 Å), particles in the form of blocks and slabs of hard point. The results showed that the conversion impregnation of copper has increased by 17% conversion to biodiesel. (author)

Microbial diversity in methanogenic hydrocarbon-degrading enrichment cultures isolated from a water-flooded oil reservoir (Dagang oil field, China)

Science.gov (United States)

Jiménez, Núria; Cai, Minmin; Straaten, Nontje; Yao, Jun; Richnow, Hans H.; Krüger, Martin

2015-04-01

Microbial transformation of oil to methane is one of the main degradation processes taking place in oil reservoirs, and it has important consequences as it negatively affects the quality and economic value of the oil. Nevertheless, methane could constitute a recovery method of carbon from exhausted reservoirs. Previous studies combining geochemical and isotopic analysis with molecular methods showed evidence for in situ methanogenic oil degradation in the Dagang oil field, China (Jiménez et al., 2012). However, the main key microbial players and the underlying mechanisms are still relatively unknown. In order to better characterize these processes and identify the main microorganisms involved, laboratory biodegradation experiments under methanogenic conditions were performed. Microcosms were inoculated with production and injection waters from the reservoir, and oil or 13C-labelled single hydrocarbons (e.g. n-hexadecane or 2-methylnaphthalene) were added as sole substrates. Indigenous microbiota were able to extensively degrade oil within months, depleting most of the n-alkanes in 200 days, and producing methane at a rate of 76 ± 6 µmol day-1 g-1 oil added. They could also produce heavy methane from 13C-labeled 2-methylnaphthalene, suggesting that further methanogenesis may occur from the aromatic and polyaromatic fractions of Dagang reservoir fluids. Microbial communities from oil and 2-methyl-naphthalene enrichment cultures were slightly different. Although, in both cases Deltaproteobacteria, mainly belonging to Syntrophobacterales (e.g. Syntrophobacter, Smithella or Syntrophus) and Clostridia, mostly Clostridiales, were among the most represented taxa, Gammaproteobacteria could be only identified in oil-degrading cultures. The proportion of Chloroflexi, exclusively belonging to Anaerolineales (e.g. Leptolinea, Bellilinea) was considerably higher in 2-methyl-naphthalene degrading cultures. Archaeal communities consisted almost exclusively of representatives of

Performance of NiWP/Al2O3 catalyst for hydroprocessing of light gas oils derived from Athabasca bitumen

Energy Technology Data Exchange (ETDEWEB)

Owusu-Boakye, A.; Ferdous, D.; Dalai, A.K. [Saskatchewan Univ., Saskatoon, SK (Canada). Dept. of Chemistry and Chemical Engineering; Adjaye, J. [Syncrude Canada Ltd., Edmonton, AB (Canada). Edmonton Research Centre

2004-07-01

The quality of diesel fuel in terms of cetane number and coloring is diminished if it has a high content of aromatics which cause the formation of undesirable emissions in exhaust gases. These compounds typically occur as mono, di, tri and polyaromatics. In response to strict environmental regulations, middle distillates now have fewer aromatics. Sulphur and nitrogen compounds in diesel fuels also cause the formation of SOx and NOx in the atmosphere, but the aromatic hydrogenation of diesel fuels is more complex than any of the hydrodesulphurization (HDS) or hydrodenitrogenation (HDN) processes. The NiWP/Al{sub 2}O{sub 3} catalyst in a trickle-bed reactor was used under a range of temperature and pressure conditions to study the reactivity of vacuum, atmospheric and hydrocracked light gas oils produced from Athabasca bitumen. The hydrogen feed ratio was kept constant and product samples from different feedstocks were analyzed with respect to sulfur, nitrogen and aromatic content. The study also included a comparison of gasoline selectivity and kinetic parameters for HDS and HDN reactions for the feed materials.

Chemical composition of olive oils of the cultivar Colombaia

Directory of Open Access Journals (Sweden)

Zunin, P.

2005-12-01

Full Text Available The chemical composition of monovarietal olive oils from the cultivar Colombaia was studied. Free acidity, peroxide value and UV absorbance attested to the good quality of the analyzed oils. Their fatty acid composition appeared to be quite different from the typical fatty acid profile of olive oils from Liguria but met the limits reported in the EC Regulations for olive oils. On the contrary, the amounts of Δ7-stigmastenol were often higher than the 0.5 % limit set by EC Regulations and total ß-sitosterol was below the minimum 93 % limit. The composition of polar compounds and of the volatile fraction was representative of the peculiar organoleptic character of these oils. Thus, the anomalous sterol composition of the monovarietal oils from the cultivar Colombaia calls for blending with other oils. Moreover, the use of these oils for the production of PDO oils “Riviera Ligure” must also be carefully controlled because it changes their nutritional and sensorial featuresEn este trabajo se ha estudiado la composición química de aceites de oliva mono-varietales de la variedad Colombaia. La acidez libre, el índice de peróxidos y la absorción UV confirmaron la buena calidad de los aceites analizados. Su composición en ácidos grasos resultó bastante diferente del perfil típico de ácidos grasos de los aceites de oliva virgen de la región de Liguria, pero se mantuvo dentro de los límites establecidos por los Reglamentos EC para aceites de oliva. Por otro lado, las cantidades de Δ7-estigmastenol resultaron normalmente superiores al 0.5 % del límite fijado por los Reglamentos EC y el ß-sitosterol total fue inferior al 93 % del límite mínimo. La composición en compuestos polares y de la fracción volátil confirmó las características organolépticas peculiares de estos aceites. Por tanto, la composición esterólica anómala de los aceites mono-varietales de la variedad Colombaia hace necesaria una mezcla con otros

Hydrotreatment of heavy oil from coal liquefaction on Sulfide Ni - W Catalysts

International Nuclear Information System (INIS)

Zhi-ping Lei; Li-juan Gao; Heng-fu Shui; Shi-biao, Ren; Zhi-cai Wang; Kang-shi Gang

2011-01-01

Heavy oil (distillation temperature: 320-340 deg C) derived from the direct coal liquefaction process using Shengli coal were hydrotreated using sulfided Ni-Mo/Al 2 O 3 , Ni-W/Al 2 O 3 , and Ni-W/SiO 2 catalysts respectively. The sulfided catalysts were characterized by BET, XRD, H 2 -TPR and NH 3 -TPD respectively. The evaluations of the hydrodenitrogenation (HDN) and hydrodearomatization (HDA) properties of heavy oil on the three catalysts were carried out at 400 deg C and 5.0 MPa initial H2 pressure. The W-based catalysts displayed better performances than Mo-based catalysts for the HDN and HDA reactions. Al 2 O 3 supported catalysts were found to have higher catalytic activities than on SiO 2 supported ones. The activities of sulfided catalysts were associated mainly with the nature of active sites, acidity, metal sulfide crystallite size and the amount of the reducible sulfur species of metal sulfide. (author)

Importance of algae oil as a source of biodiesel

International Nuclear Information System (INIS)

Demirbas, Ayhan; Fatih Demirbas, M.

2011-01-01

Algae are the fastest-growing plants in the world. Industrial reactors for algal culture are open ponds, photobioreactors and closed systems. Algae are very important as a biomass source. Algae will some day be competitive as a source for biofuel. Different species of algae may be better suited for different types of fuel. Algae can be grown almost anywhere, even on sewage or salt water, and does not require fertile land or food crops, and processing requires less energy than the algae provides. Algae can be a replacement for oil based fuels, one that is more effective and has no disadvantages. Algae are among the fastest-growing plants in the world, and about 50% of their weight is oil. This lipid oil can be used to make biodiesel for cars, trucks, and airplanes. Microalgae have much faster growth-rates than terrestrial crops. the per unit area yield of oil from algae is estimated to be from 20,000 to 80,000 l per acre, per year; this is 7-31 times greater than the next best crop, palm oil. The lipid and fatty acid contents of microalgae vary in accordance with culture conditions. Most current research on oil extraction is focused on microalgae to produce biodiesel from algal oil. Algal-oil processes into biodiesel as easily as oil derived from land-based crops.

The mother of all oil spills and the Dawhat ad Dafi

International Nuclear Information System (INIS)

O'Brien, J.L.; Gallagher, J.J.

1993-01-01

The Gulf War (Operation Desert Storm) produced some of the largest oil spills of all time when Saddam Hussein released millions of barrels of oil from the Mina al Ahmadi terminal in Kuwait into the Arabian Gulf. The resulting massive spill descended on the Saudi Arabian coastline threatening its industrial and environmental resources, as well as the desalination plant intakes that provide fresh water for most of the eastern provinces of the country. A fortuitous combination of geographical features, natural phenomena, and defensive preparations by Saudi Arabia averted a catastrophe of substantial proportions as the open-quotes mother of all oil spillsclose quotes impacted that country

Al/ oil nanofluids inside annular tube: an experimental study on convective heat transfer and pressure drop

Science.gov (United States)

Jafarimoghaddam, Amin; Aberoumand, Sadegh; Javaherdeh, Kourosh; Arani, Ali Akbar Abbasian; Jafarimoghaddam, Reza

2018-04-01

In this work, an experimental study on nanofluid preparation stability, thermo-physical properties, heat transfer performance and friction factor of Al/ Oil nanofluids has been carried out. Electrical Explosion Wire ( E.E.W) which is one of the most reliable one-step techniques for nanofluids preparation has been used. An annular tube has been considered as the test section in which the outer tube was subject to a uniform heat flux boundary condition of about 204 W. The utilized nanofluids were prepared in three different volume concentrations of 0.011%, 0.044% and 0.171%. A wide range of parameters such as Reynolds number Prandtl number, viscosity, thermal conductivity, density, specific heat, convective heat transfer coefficient, Nusselt number and the friction factor have been studied. The experiment was conducted in relatively low Reynolds numbers of less than 160 and within a hydrodynamically fully-developed regime. According to the results, thermal conductivity, density and viscosity increased depending on the volume concentrations and working temperatures while the specific heat declined. More importantly, it was observed that convective heat transfer coefficient and Nusselt number enhanced by 28.6% and 16.4%, respectively, for the highest volume concentration. Finally, the friction factor (which plays an important role in the pumping power) was found to be increased around 18% in the volume fraction of 0.171%.

Oil shale research related to proposed nuclear projects

Energy Technology Data Exchange (ETDEWEB)

Carpenter, H C; Sohns, H W; Dinneen, G U [Laramie Petroleum Research Center, Bureau of Mines, Department of the Interior, Laramie, WY (United States)

1970-05-15

The Bureau of Mines is conducting research to develop data pertinent to in situ retorting of oil shale fractured by a nuclear explosion or other means. Maximum utilization of the Green River oil shale found in Colorado, Utah, and Wyoming, at depths ranging from outcrops to several thousand feet, requires development of several methods of processing. Early research was devoted to developing processes for application to oil shale occurring at depths suitable for mining. In present research, the emphasis is on in situ retorting and recovery processes that would be more satisfactory for oil shales occurring at greater depths. Development of an in situ process depends upon finding or establishing sufficient permeability in the oil shale beds for the passage of fluids which serve as a heat carrier in bringing the oil shale to retorting temperature. Use of a nuclear explosive seems to offer the best chance for successfully fracturing the thicker and more deeply buried portions of the deposit to give the required permeability. Processing the very large quantity of broken and fractured oil shale that would be produced presents many problems which require new background data for their solution. This paper describes research the Bureau of Mines is conducting to develop pertinent data. Primarily this research involves laboratory determination of properties of oil shale, pilot scale investigation of retorting characteristics of ungraded broken shale, and underground combustion of shale fractured by pressure and chemical explosives. Application of the research results should aid in designing the oil recovery phase and provide an estimate of the quantity of oil that may be obtained in a nuclear experiment in oil shale. (author)

Oil shale research related to proposed nuclear projects

International Nuclear Information System (INIS)

Carpenter, H.C.; Sohns, H.W.; Dinneen, G.U.

1970-01-01

The Bureau of Mines is conducting research to develop data pertinent to in situ retorting of oil shale fractured by a nuclear explosion or other means. Maximum utilization of the Green River oil shale found in Colorado, Utah, and Wyoming, at depths ranging from outcrops to several thousand feet, requires development of several methods of processing. Early research was devoted to developing processes for application to oil shale occurring at depths suitable for mining. In present research, the emphasis is on in situ retorting and recovery processes that would be more satisfactory for oil shales occurring at greater depths. Development of an in situ process depends upon finding or establishing sufficient permeability in the oil shale beds for the passage of fluids which serve as a heat carrier in bringing the oil shale to retorting temperature. Use of a nuclear explosive seems to offer the best chance for successfully fracturing the thicker and more deeply buried portions of the deposit to give the required permeability. Processing the very large quantity of broken and fractured oil shale that would be produced presents many problems which require new background data for their solution. This paper describes research the Bureau of Mines is conducting to develop pertinent data. Primarily this research involves laboratory determination of properties of oil shale, pilot scale investigation of retorting characteristics of ungraded broken shale, and underground combustion of shale fractured by pressure and chemical explosives. Application of the research results should aid in designing the oil recovery phase and provide an estimate of the quantity of oil that may be obtained in a nuclear experiment in oil shale. (author)

Bioremediation potential of crude oil spilled on soil

International Nuclear Information System (INIS)

McMillen, S.J.; Young, G.N.; Davis, P.S.; Cook, P.D.; Kerr, J.M.; Gray, N.R.; Requejo, A.G.

1995-01-01

Spills sometimes occur during routine operations associated with exploration and production (E and P) of crude oil. These spills at E and P sites typically are small, less than 1 acre (0.4 ha), and the spill may be in remote locations. As a result, bioremediation often represents a cost-effective alternative to other cleanup technologies. The goal of this study was to determine the potential for biodegrading a range of crude oil types and determining the effect of process variables such as soil texture and soil salinity. Crude oils evaluated ranged in American Petroleum institute (API) gravity from 14 degree to 45 degree. The extent of biodegradation was calculated from oxygen uptake data and the total extractable material (TEM) concentration. Based on the data collected, a simple model was developed for predicting the bioremediation potential of a range of crude oil types. Biodegradation rates were significantly lower in sandy soils. Soil salinities greater than approximately 40 mmhos/cm adversely impacted soil microbial activity and biodegradation rate

Comparison of quartz tuning forks and AlN-based extensional microresonators for viscosity measurements in oil/fuel mixtures

Science.gov (United States)

Toledo, J.; Manzaneque, T.; Hernando-García, J.; Vazquez, J.; Ababneh, A.; Seidel, H.; Lapuerta, M.; Sánchez-Rojas, J. L.

2013-05-01

In-situ monitoring of the physical properties of liquids is of great interest in the automotive industry. For example, lubricants are subject to dilution with diesel fuel as a consequence of late-injection processes, which are necessary for regenerating diesel particulate filters. This dilution can be determined by tracking the viscosity and the density of the lubricant. Here we report the test of two in-plane movement based resonators to explore their capability to monitor oil dilution with diesel and biodiesel. One of the resonators is the commercially available millimeter-sized quartz tuning fork, working at 32.7 kHz. The second resonator is a state-of-the-art micron-sized AlN-based rectangular plate, actuated in the first extensional mode in the MHz range. Electrical impedance measurements were carried out to characterize the performance of the structures in various liquid media in a wide range of viscosities. These measurements were completed with the development of low-cost electronic circuits to track the resonance frequency and the quality factor automatically, these two parameters allow to obtain the viscosity of various fluids under investigation, as in the case of dilution of lubricant SAE 15W40 and biodiesel.

Upgrading of the liquid fuel from fast pyrolysis of biomass over MoNi/γ-Al2O3 catalysts

International Nuclear Information System (INIS)

Xu, Ying; Wang, Tiejun; Ma, Longlong; Zhang, Qi; Liang, Wei

2010-01-01

The hydrotreatment of bio-oil, which obtained from fast pyrolysis of pine sawdust, was investigated over MoNi/γ-Al 2 O 3 catalyst under mild conditions (373 K, 3 MPa hydrogen pressure). Acetic acid was taken as a model compound to investigate the effects of Mo promoter contents and reducing temperatures of catalysts on the catalysts activity under the condition of 473 K and 3 MPa hydrogen pressure. X-ray diffraction and temperature programmed reduction showed that the addition of Mo promoter benefited the uniformity of nickel species and inhibited the formation of NiAl 2 O 4 spinel in the catalysts. The GC spectrum of liquid products showed the mechanism of the model reaction. The maximum conversion of acetic acid (33.20%) was attained over 0.06MoNi/γ-Al 2 O 3 catalysts being reduced at 873 K. This catalyst was chosen for the upgrading of raw bio-oil. After the upgrading process, the pH value of the bio-oil increased from 2.33 to 2.77. The water content increased from 35.52 wt.% to 41.55 wt.% and the gross calorific value increased from 13.96 MJ/kg to 14.17 MJ/kg. The hydrogen content in the bio-oil increased from 6.25 wt.% to 6.95 wt.%. The product properties of the upgraded bio-oil, particularly the hydrogen content and the acidity were considerably improved. The results of gas chromatography-mass spectrometry analysis showed that both hydrotreatment and esterification had happened over 0.06MoNi/γ-Al 2 O 3 (873) catalyst during the upgrading process.

Greenhouse gas emissions and energy balance of palm oil biofuel

Energy Technology Data Exchange (ETDEWEB)

de Souza, Simone Pereira; Pacca, Sergio [Graduate Program on Environmental Engineering Science, School of Engineering of Sao Carlos, University of Sao Paulo, Rua Arlindo Bettio, 1000 Sao Paulo (Brazil); de Avila, Marcio Turra; Borges, Jose Luiz B. [Brazilian Agricultural Research Corporation (Embrapa - Soja) (Brazil)

2010-11-15

The search for alternatives to fossil fuels is boosting interest in biodiesel production. Among the crops used to produce biodiesel, palm trees stand out due to their high productivity and positive energy balance. This work assesses life cycle emissions and the energy balance of biodiesel production from palm oil in Brazil. The results are compared through a meta-analysis to previous published studies: Wood and Corley (1991) [Wood BJ, Corley RH. The energy balance of oil palm cultivation. In: PORIM intl. palm oil conference - agriculture; 1991.], Malaysia; Yusoff and Hansen (2005) [Yusoff S, Hansen SB. Feasibility study of performing an life cycle assessment on crude palm oil production in Malaysia. International Journal of Life Cycle Assessment 2007;12:50-8], Malaysia; Angarita et al. (2009) [Angarita EE, Lora EE, Costa RE, Torres EA. The energy balance in the palm oil-derived methyl ester (PME) life cycle for the cases in Brazil and Colombia. Renewable Energy 2009;34:2905-13], Colombia; Pleanjai and Gheewala (2009) [Pleanjai S, Gheewala SH. Full chain energy analysis of biodiesel production from palm oil in Thailand. Applied Energy 2009;86:S209-14], Thailand; and Yee et al. (2009) [Yee KF, Tan KT, Abdullah AZ, Lee KT. Life cycle assessment of palm biodiesel: revealing facts and benefits for sustainability. Applied Energy 2009;86:S189-96], Malaysia. In our study, data for the agricultural phase, transport, and energy content of the products and co-products were obtained from previous assessments done in Brazil. The energy intensities and greenhouse gas emission factors were obtained from the Simapro 7.1.8. software and other authors. These factors were applied to the inputs and outputs listed in the selected studies to render them comparable. The energy balance for our study was 1:5.37. In comparison the range for the other studies is between 1:3.40 and 1:7.78. Life cycle emissions determined in our assessment resulted in 1437 kg CO{sub 2}e/ha, while our analysis

Tough Blends of Polylactide and Castor Oil

Energy Technology Data Exchange (ETDEWEB)

Robertson, Megan L.; Paxton, Jessica M.; Hillmyer, Marc A. (UMM)

2012-10-10

Poly(l-lactide) (PLLA) is a renewable resource polymer derived from plant sugars with several commercial applications. Broader implementation of the material is limited due to its inherent brittleness. We show that the addition of 5 wt % castor oil to PLLA significantly enhances the overall tensile toughness with minimal reductions in the modulus and no plasticization of the PLLA matrix. In addition, we used poly(ricinoleic acid)-PLLA diblock copolymers, synthesized entirely from renewable resources, as compatibilizers for the PLLA/castor oil blends. Ricinoleic acid, the majority fatty acid comprising castor oil, was polymerized through a lipase-catalyzed condensation reaction. The resulting polymers contained a hydroxyl end-group that was subsequently used to initiate the ring-opening polymerization of L-lactide. The binary PLLA/castor oil blend exhibited a tensile toughness seven times greater than neat PLLA. The addition of block copolymer allowed for control over the morphology of the blends, and even further improvement in the tensile toughness was realized - an order of magnitude larger than that of neat PLLA.

Tough blends of polylactide and castor oil.

Science.gov (United States)

Robertson, Megan L; Paxton, Jessica M; Hillmyer, Marc A

2011-09-01

Poly(l-lactide) (PLLA) is a renewable resource polymer derived from plant sugars with several commercial applications. Broader implementation of the material is limited due to its inherent brittleness. We show that the addition of 5 wt % castor oil to PLLA significantly enhances the overall tensile toughness with minimal reductions in the modulus and no plasticization of the PLLA matrix. In addition, we used poly(ricinoleic acid)-PLLA diblock copolymers, synthesized entirely from renewable resources, as compatibilizers for the PLLA/castor oil blends. Ricinoleic acid, the majority fatty acid comprising castor oil, was polymerized through a lipase-catalyzed condensation reaction. The resulting polymers contained a hydroxyl end-group that was subsequently used to initiate the ring-opening polymerization of l-lactide. The binary PLLA/castor oil blend exhibited a tensile toughness seven times greater than neat PLLA. The addition of block copolymer allowed for control over the morphology of the blends, and even further improvement in the tensile toughness was realized-an order of magnitude larger than that of neat PLLA.

Multivariate FIGARCH and long memory process: evidence of oil price markets

Directory of Open Access Journals (Sweden)

Nadhem Selmi

2015-09-01

Full Text Available Oil price markets can benefit from a better considerate of how shocks can affect volatility through time. This study assesses the impact of structural changes and outliers on volatility persistence of two crude oil markets WTI and Brent oil price between January 1, 1996 and March 17, 2014. First, we identify the FIGARCH process proposed by Baillie et al. (1996 [Baillie, R.T., Bollerslev, T., & Mikkelsen, H.O., (1996, Fractionally integrated generalized autoregressive conditional heteroscedasticity. Journal of Econometrics, 74, 3-30.] and investigate some of its statistical proprieties and then incorporate this information into the volatility modelling. We also show that outliers can bias the estimation of the persistence of the volatility. Taking into account outliers on the volatility modelling process improve the understanding of volatility in crude oil markets.

Satellite and airborne oil spill remote sensing: State of the art and application to the BP DeepWater Horizon oil spill

Science.gov (United States)

Leifer, I.; Clark, R.; Jones, C.; Holt, B.; Svejkovsky, J.; Swayze, G.

2011-01-01

The vast, persistent, and unconstrained oil release from the DeepWater Horizon (DWH) challenged the spill response, which required accurate quantitative oil assessment at synoptic and operational scales. Experienced observers are the mainstay of oil spill response. Key limitations are weather, scene illumination geometry, and few trained observers, leading to potential observer bias. Aiding the response was extensive passive and active satellite and airborne remote sensing, including intelligent system augmentation, reviewed herein. Oil slick appearance strongly depends on many factors like emulsion composition and scene geometry, yielding false positives and great thickness uncertainty. Oil thicknesses and the oil to water ratios for thick slicks were derived quantitatively with a new spectral library approach based on the shape and depth of spectral features related to C-H vibration bands. The approach used near infrared, imaging spectroscopy data from the AVIRIS (Airborne Visual/InfraRed Imaging Spectrometer) instrument on the NASA ER-2 stratospheric airplane. Extrapolation to the total slick used MODIS satellite visual-spectrum broadband data, which observes sunglint reflection from surface slicks; i.e., indicates the presence of oil and/or surfactant slicks. Oil slick emissivity is less than seawater's allowing MODIS thermal infrared (TIR) nighttime identification; however, water temperature variations can cause false positives. Some strong emissivity features near 6.7 and 9.7 ??m could be analyzed as for the AVIRIS short wave infrared features, but require high spectral resolution data. TIR spectral trends can allow fresh/weathered oil discrimination. Satellite Synthetic Aperture Radar (SSAR) provided synoptic data under all-sky conditions by observing oil dampening of capillary waves; however, SSAR typically cannot discriminate thick from thin oil slicks. Airborne UAVSAR's significantly greater signal-to-noise ratio and fine spatial resolution allowed

Response of adult mallard ducks to ingested South Louisiana crude oil

Science.gov (United States)

Coon, N.C.; Dieter, M.P.

1981-01-01

Adult mallards (Anas platyrhynchos) were fed South Louisiana crude oil as 0.25 and 2.5% of the total diet for 26 weeks to assess the chronic effects of oil ingestion. Additional birds were fed diets containing either 1.0% of a paraffin mixture or clean feed. No birds died during the study, nor were their body weights significantly depressed. Oviduct weight at necropsy was greatly reduced in hens on the 2.5% oil diet and also was significantly reduced in hens on the 0.25% oil diet when compared with controls. Male reproductive organs were not atrophied by treatment. Hens on oil-treated diets laid fewer eggs than those on the control diet; however, eggs from treated hens hatched as well as those from controls when artificially incubated. Pathological or biochemical alterations were no greater in the treated birds than in controls.

Use of adsorption and gas chromatographic techniques in estimating biodegradation of indigenous crude oils

International Nuclear Information System (INIS)

Kokub, D.; Allahi, A.; Shafeeq, M.; Khalid, Z.M.; Malik, K.A.; Hussain, A.

1993-01-01

Indigenous crude oils could be degraded and emulsified upto varying degree by locally isolated bacteria. Degradation and emulsification was found to be dependent upon the chemical composition of the crude oils. Tando Alum and Khashkheli crude oils were emulsified in 27 and 33 days of incubation respectively. While Joyamair crude oil and not emulsify even mainly due to high viscosity of this oil. Using adsorption chromatographic technique, oil from control (uninoculated) and bio degraded flasks was fractioned into the deasphaltened oil containing saturate, aromatic, NSO (nitrogen, sulphur, oxygen) containing hydrocarbons) and soluble asphaltenes. Saturate fractions from control and degraded oil were further analysed by gas liquid chromatography. From these analyses, it was observed that saturate fraction was preferentially utilized and the crude oils having greater contents of saturate fraction were better emulsified than those low in this fraction. Utilization of various fractions of crude oils was in the order saturate> aromatic> NSO. (author)

Kinetics of oil-cracking for different types of marine oils from Tahe Oilfield, Tarim Basin, NW China

Directory of Open Access Journals (Sweden)

Anlai Ma

2016-02-01

Full Text Available The C1–C5 gas and carbon isotope ratios generated during the cracking of heavy, normal and high-waxy marine oils from Tahe Oilfield, Tarim Basin, NW China, using a closed-gold tube system under high pressure were presented. The three types of oil tested resulted in a similar gas-generation process. The C2–C5 range initially increased its yield with the application of pyrolysis temperature and thereafter decreased, while the C1 yield increased with the same application. High-waxy oil had the highest C1–C5 yield of 510 mg/goil, whereas heavy oil had the lowest C1–C5 yield of 316 mg/goil. The δ13C1 value was low at first, but gradually became higher as the pyrolysis temperature increased. However, the δ13C2 and δ13C3 values gradually became higher when the temperature was greater than 420 °C. The kinetic parameters of the C1–C5 gas generation for the different types of marine oils were then calculated using KINETIC software. This calculation resulted in a frequency factor of about 1.78 × 1014 s−1, while the distribution of the activation energy of the C1–C5 gas mass generated was relatively narrow with a range from 56 to 66 kcal/mol. Among the three types of oil tested, heavy oil had the widest activation energy distribution and the lowest major frequency of activation energy. The maximum temperature at which oil could be preserved as a separate oil phase varied from about 178 °C at a slow geological heating rate to 206 °C at a fast geological heating rate. This result is based on the kinetic parameters determined and in combination with the fractional conversion (C of oil to gas. Testing conducted at the volatile Middle Cambrian reservoir of well Zhongshen 1 in the Tazhong Uplift strongly supported this conclusion.

Investigating the Use of Crude Atili Oil for Maintenance of Stock ...

African Journals Online (AJOL)

BSN

location, climate, substrate type, fauna and flora distribution. Few countries have been ... morphological changes (Santos et al, 2005). Prolonged storage in, and .... Table 1: Effect of various concentrations of Atili oil on the fungi. Fungus species.

Regeneration of Waste Edible Oil by the Use of Virgin and Calcined Magnesium Hydroxide as Adsorbents.

Science.gov (United States)

Ogata, Fumihiko; Kawasaki, Naohito

2016-01-01

In this study, we prepared virgin (S, L) and calcined (S-380, S-1000, L-380, L-1000) magnesium hydroxide for regeneration of waste edible oil. Deterioration of soybean oil, rapeseed oil, and olive oil was achieved by heat and aeration treatment. The properties of the different adsorbents were investigated using specific surface area measurements, scanning electron microscopy, X-ray diffraction analysis, thermogravimetric-differential thermal analysis, and surface pH measurement. Moreover, the relationship between the changes in acid value (AV) and carbonyl value (CV) and the adsorbent properties were evaluated. The specific surface areas of S-380 and L-380 were greater than that of other adsorbents. In addition, the XRD results show that S-380 and L-380 contain both magnesium hydroxide and magnesium oxide structures. The decreases in AV and CV using S-380 and L-380 were greater than achieved using other adsorbents. The correlation coefficients between the decrease in AV and CV and specific surface area were 0.947 for soybean oil, 0.649 for rapeseed oil, and 0.773 for olive oil, respectively. The results obtained in this study suggest that a physical property of the adsorbent, namely specific surface area, was primarily responsible for the observed decreases in AV and CV. Overall, the results suggest that S-380 and L-380 are useful for the regeneration of waste edible oil.

Oil palm deserves government attention in Brazil

Science.gov (United States)

Moreira, José R.; Goldemberg, José

2015-07-01

Englund et al (2015 Environ. Res. Lett. 10 044002) have recently analyzed biodiesel production from oil palm plantations as one possible way to mitigate climate change while providing cost effective results. They show that data for detailed quantification of biological carbon sequestration is available allowing a high confidence evaluation of positive impacts when oil palm plantation for food and biodiesel production is carried out in degraded, cultivated soil, and also with some varieties of natural vegetation in the Amazon. Nevertheless, economic risk associated with the future price of fossil fuels and uncertainties related with carbon subsidy are barriers. Here we discuss the assumptions under which such controversial proposal is based and suggest further analysis for Brazilian decision makers.

The impacts of oil lakes on the fresh groundwater lenses in Kuwait

Energy Technology Data Exchange (ETDEWEB)

Hadi, K. [Kuwait Inst. for Scientific Research, Water Resources Div., Safat (Kuwait)

2002-07-01

A study was undertaken in 1992-93 following the Gulf War to determine the extent of groundwater pollution resulting from the setting afire of hundreds of oil wells in Kuwait. The country's only natural water resource is groundwater, which is mostly brackish except for two locations where it exists as fresh lenses due to the high infiltration rate of the sandy Dibdibba Formation. However, the quality of the fresh groundwater lens at Raudhatain and Umm Al-Aish was threatened when the ground surface became heavily polluted from the fires. The main goal of the study was to measure the concentration of heavy metals such as vanadium, nickel, chromium, lead, cadmium, and hydrocarbons to estimate background levels of these contaminants in ground water in the Raudhatain and Umm Al-Aish areas and to determine the impacts of hydrocarbon pollution on the quality of groundwater. Results show that concentration of certain pollutants in the water samples from wells close to the contaminated areas exceed international standards, while other monitored wells do not show pollution from oil spills. However, it was noted that non detection of pollution does not necessarily imply that the groundwater is not polluted. The sources of pollution include infiltration from oil lakes and contaminated water used for fire fighting, products of combustion at the ground surface, and surface leakage of oil from damaged oil well casings. 5 refs., 5 tabs., 1 fig.

Upgrading Unconventional Oil Resources with the EST Process

Energy Technology Data Exchange (ETDEWEB)

Delbianco, Alberto; Meli, Salvatori; Panariti, Nicolleta; Rispoli, Giacomo

2007-07-01

We strongly believe that unconventional oils will play a much larger role in the growth of supply than is currently recognized. As a matter of fact, whereas the earth's conventional proven world oil reserves are 1.3 trillion barrels, extra-heavy plus bitumen resources amount to about 4 trillion barrels. The unconventional oils are characterized by low API gravity (<10), high viscosity and high concentration of poisons such as sulphur, nitrogen, metals, and asphaltenes. For this reason, a key role for the full exploitation of these hydrocarbon resources is played by the downstream processes that are required to upgrade and convert them into valuable products. In this scenario, Eni has developed a novel hydrocracking process (EST: Eni Slurry Technology) which is particularly well-suited for the conversion and upgrading of heavy feedstocks (conventional vacuum residues, extra-heavy oils and bitumen). EST employs nano-sized hydrogenation catalysts and an original process scheme that allow complete feedstock conversion to an upgraded synthetic crude oil (SCO) with an API gravity gain greater than 20 and avoid the production of residual by-products, such as pet-coke or heavy fuel oil. A Commercial Demonstration Unit (CDP) of 1200 bbl/d capacity is successfully operating in the Eni's Taranto refinery since November 2005. (auth)

The impact of energy derivatives on the crude oil market

Energy Technology Data Exchange (ETDEWEB)

Fleming, J.; Ostdiek, B. [Jones Graduate School of Management, Rice University, MS 531, P.O. Box 1892 Houston, TX (United States)

1999-04-01

We examine the effects of energy derivatives trading on the crude oil market. There is a common public and regulatory perception that derivative securities increase volatility and can have a destabilizing effect on the underlying market. Consistent with this view, we find an abnormal increase in volatility for three consecutive weeks following the introduction of NYMEX crude oil futures. While there is also evidence of a longer-term volatility increase, this is likely due to exogenous factors, such as the continuing deregulation of the energy markets. Subsequent introductions of crude oil options and derivatives on other energy commodities have no effect on crude oil volatility. We also examine the effects of derivatives trading on the depth and liquidity of the crude oil market. This analysis reveals a strong inverse relation between the open interest in crude oil futures and spot market volatility. Specifically, when open interest is greater, the volatility shock associated with a given unexpected increase in volume is much smaller. (Copyright (c) 1999 Elsevier Science B.V., Amsterdam. All rights reserved.)

The impact of energy derivatives on the crude oil market

International Nuclear Information System (INIS)

Fleming, J.; Ostdiek, B.

1999-01-01

We examine the effects of energy derivatives trading on the crude oil market. There is a common public and regulatory perception that derivative securities increase volatility and can have a destabilizing effect on the underlying market. Consistent with this view, we find an abnormal increase in volatility for three consecutive weeks following the introduction of NYMEX crude oil futures. While there is also evidence of a longer-term volatility increase, this is likely due to exogenous factors, such as the continuing deregulation of the energy markets. Subsequent introductions of crude oil options and derivatives on other energy commodities have no effect on crude oil volatility. We also examine the effects of derivatives trading on the depth and liquidity of the crude oil market. This analysis reveals a strong inverse relation between the open interest in crude oil futures and spot market volatility. Specifically, when open interest is greater, the volatility shock associated with a given unexpected increase in volume is much smaller. (Copyright (c) 1999 Elsevier Science B.V., Amsterdam. All rights reserved.)

Do high oil prices justify an increase in taxation in a mature oil province? The case of the UK continental shelf

International Nuclear Information System (INIS)

Nakhle, Carole

2007-01-01

In response to the structural shift in oil price coupled with greater import dependency, concerns about security of supply have once again emerged as a major policy issue. The UK, the largest producer of oil and natural gas in the European Union, became a net importer of natural gas in 2004, and according to Government estimates will become a net importer of oil by the end of the decade. A weakened North Sea performance means extra reliance, both for the UK and Europe as a whole, on global oil and gas network and imports. In 2002, the UK Government introduced a 10% supplementary charge and in 2005, doubled the charge to 20% in an attempt to capture more revenues from the oil industry as a result of the increase in the price of crude oil. However, higher tax rates do not necessarily generate higher fiscal revenue and in the long term may result in materially lower revenues if investment is discouraged as indeed occurred when the 2007 UK Annual Budget statement showed a shortfall in North Sea oil revenues below forecasts of Pounds 4 billion. It is therefore argued that the increase in the fiscal take came at the wrong time for the UK Continental Shelf and that the UK Government's concern should have been to encourage more oil production from its declining province, especially in the light of the rising concern surrounding the security of supply

Responses of tropical fruit bats to monoculture and polyculture farming in oil palm smallholdings

Science.gov (United States)

Syafiq, Muhamad; Nur Atiqah, Abd Rahman; Ghazali, Amal; Asmah, Siti; Yahya, Muhammad S.; Aziz, Najjib; Puan, Chong Leong; Azhar, Badrul

2016-07-01

The oil palm industry is one of the main economic drivers in Southeast Asia. The industry has caused tropical deforestation on a massive scale in producing countries, and this forest conversion to oil palm agriculture has decimated the habitat of numerous native species. Monoculture and polyculture practices are two distinctive oil palm production systems. We hypothesize that polyculture farming hosts a greater diversity of species than monoculture farming. Habitat complexity in smallholdings is influenced by multiple farming practices (i.e. polyculture and monoculture). However, little is known about the effects of such farming practices in smallholdings on mammalian biodiversity, and particularly frugivorous bats. Our study aimed to find the best farming practice to reconcile oil palm production with biodiversity conservation. Mist-nets were used to trap frugivorous bats at 120 smallholdings in Peninsular Malaysia. We compared species richness and the abundance of frugivorous bats between monoculture and polyculture smallholdings. We investigated their relationships with vegetation structure characteristics. Our results revealed that species richness and abundance of frugivorous bats were significantly greater in polyculture smallholdings than monoculture smallholdings. We also found that 28.21% of the variation in species richness was explained by in situ habitat characteristics, including the number of dead standing oil palms and immature oil palms, non-grass cover, height of non-grass cover, and farming practices. The in situ habitat quality was closely associated with oil palm farming management. Commercial growers should implement polyculture rather than monoculture farming because polyculture farming has positive effects on the abundance and species richness of bats in oil palm production landscapes.

Improved surfactants formulation for remediation of oil sludge recovery

International Nuclear Information System (INIS)

Syed Hakimi Sakuma Syed Ahmad; Shahidan Radiman

2000-01-01

Surfactant enhanced remediation based on mobilisation of the residual NAPLs (oil sludge) which is radioactive depends on the tendency of the surfactants to lower interfacial tension. Mobilisation has greater potential than solubilisation to increase the rate of remediation. Optimised surfactants formulation was determined with concentration of Aqua 2000 and D Bond of 1% wt respectively, sodium chloride concentration of 2 gmL -1 and addition of 3% wt butanol as cosolvent. The formulation was of benefit not only able to decrease further the interfacial tension of aqueous solution containing oil emulsion, but also to make possible to be more mobile and destruction of mixed liquid crystals that formed. Formation of liquid crystals can hinders significantly recovery efficiency of aqueous solution containing oil emulsion in field remediation work. In a 100 litres soil column experiment conducted containing oil emulsion in field sludge soil and using the surfactants formulation for flushing, miniemulsion formed sizes maintained at average size between 125 nm and 280 nm before and after remediation. Total oil and grease concentration removed from the soil were significant due to the decreased in oil emulsion sizes, increase mobility and solubility. (Author)

Another look on the relationships between oil prices and energy prices

International Nuclear Information System (INIS)

Lahiani, Amine; Miloudi, Anthony; Benkraiem, Ramzi; Shahbaz, Muhammad

2017-01-01

This paper employs the Quantile Autoregressive Distributed Lags (QARDL) model developed recently by Cho et al. (2015) to investigate the pass-through of oil prices to a set of energy prices. This approach allows analyzing simultaneously short-term connections and long-run cointegrating relationships across a range of quantiles. It also provides insights on the short-run predictive power of oil prices in predicting energy prices while accounting for the cointegration between oil prices and each of the considered energy prices in low, medium and high quantiles. Two key findings emerge from this paper. First, all considered energy prices are shown to be cointegrated with oil price across quantiles meaning that a stationaryequilibriumrelationship exists between single energy price and oil price. Second, we find evidence that oil price is a significant predictor of individual petroleum products prices and natural gas in the short run. This paper has important policy implications for forecasters, energy policy-makers and portfolio managers. - Highlights: • The pass-through of oil prices to a set of energy prices is investigated for US economy. • All considered energy prices are shown to be cointegrated with oil price across quantiles. • Oil price is a significant predictor of individual petroleum products prices in the short run. • Oil price also predicts natural gas prices in the short run.

EFFECTS OF OIL PRICE SHOCKS ON THE ECONOMIC SECTORS IN MALAYSIA

Directory of Open Access Journals (Sweden)

Mohd Shahidan Shaari

2013-10-01

Full Text Available This paper aims to examine the effects of oil price shocks on economic sectors in Malaysia. A unit root test was conducted, in which data were shown to be non-stationary in all levels, and stationary in the first difference for all variables. The co-integration model was applied, and the results indicated that one co-integrating equation exists, suggesting the long-term effects of oil prices on the agriculture, construction, manufacturing, and transportation sectors. Finally, Grange causality test was performed, and the results implied that in Malaysia, oil price shocks can affect agriculture, similar to Hanson et al. (2010. Oil price instability also influences the performance of the agriculture sector, contrary to the results of Alper and Torul (2009. In addition, the construction sector was found to be dependent on oil prices. Therefore, the current study has an important implication for the Malaysian government in formulating policies on oil prices. The Malaysian government needs to control the price to ensure that unstable price will not harm the agriculture, manufacturing, and construction sectors.

Histopathologic lesions in sea otters exposed to crude oil

Energy Technology Data Exchange (ETDEWEB)

Lipscomb, T.P.; Harris, R.K.; Moeller, R.B.; Pletcher, J.M.; Haebler, R.J.; Ballachey, B.E. (Armed Forces Institute of Pathology, Washington, DC (United States))

1993-01-01

Following the Exxon Valdez oil spill in Prince William Sound, Alaska, sea otters (Enhydra lutris) that appeared to be contaminated with oil, that were in danger of becoming contaminated, or that were behaving abnormally were captured and taken to rehabilitation centers. Exposure to oil was assessed by visual examination when otters arrived at the centers. Degree of oil exposure was graded according to the following criteria: oil covering greater than 60% of the body--heavily contaminated; oil covering 30-60% of the body--moderately contaminated; oil covering less than 30% of the body or light sheen on fur--lightly contaminated. If there was no oil visible, otters were considered uncontaminated. Tissues from 51 oil-contaminated sea otters (14 males, 37 females) and from six uncontaminated sea otters (three males, three females) that died in rehabilitation centers were examined histologically. Among oil-contaminated sea otters, 19/46 had interstitial pulmonary emphysema, 13/40 had gastric erosion and hemorrhage, 11/47 had centrilobular hepatic necrosis, 14/47 had periportal to diffuse hepatic lipidosis, and 10/42 had renal tubular lipidosis. Of the uncontaminated sea otters, 1/6 had gastric erosion and hemorrhage and 1/6 had diffuse hepatic lipidosis. Histologic examinations were performed on tissues from five sea otters found dead with external oil present 15 to 16 days after the spill. Periportal hepatic lipidosis and renal tubular lipidosis were found in 3/5, and interstitial pulmonary emphysema was found in 1/5. Tissues from six apparently normal sea otters collected from an area not affected by an oil spill were examined histologically, and none of these lesions were found. We conclude that interstitial pulmonary emphysema, centrilobular hepatic necrosis, and hepatic and renal lipidosis of sea otters were associated with exposure to crude oil. Gastric erosion and hemorrhage may have been associated with stress of captivity and/or oil exposure.

Chemical composition and toxicities of essential oil of Illicium ...

African Journals Online (AJOL)

use

2011-12-12

Dec 12, 2011 ... prenylated phenylpropanoids, and sesqui-neolignans have been isolated from this plant (Moriyama et al., 2007,. 2008). During our mass screening program for new agrochemicals from the wild plants, essential oil of I. fargesii fruits was found to possess insecticidal activities against the maize weevil, ...

Reserve growth in oil pools of Alberta : model and forecast

Energy Technology Data Exchange (ETDEWEB)

Verma, M.; Cook, T. [United States Geological Survey, Denver, CO (United States). Central Region

2010-09-15

This paper presented a reserve growth study that was conducted on oil pools in Alberta, Canada. Historical oil reserve data were evaluated to assess the potential for future reserve growth in both pools and fields, and reserve growth models and functions were developed to better forecast hydrocarbon volumes. The study also considered the sensitivity of reserve growth to such factors as pool size, porosity, and oil gravity. From 1960 to 2005, the reported known recoverable oil in Alberta, excluding the Athabasca oil sands and including only pools with adequate data, increased from 4.2 to 13.9 billion barrels of oil (BBO). New discoveries contributed 3.7 BBO and reserve growth added 6 BBO. Most reserve growth occurred in pools with more than 125,000 barrels of oil. Light-oil pools account for most of the total known oil volume and consequently showed the lowest growth. Pools with greater than 30 percent porosity grew more than pools with lower porosity reservoirs. Oil field growth was found to be almost twice that of pool growth, possibly because the analysis evaluated fields with two or more pools discovered in different years. The growth in oil volumes in Alberta pools is projected to be about 454 million barrels of oil in the period from 2006 to 2010. Over a 25-year period, the cumulative reserve growth in Alberta oil pools was substantially lower than other major petroleum-producing regions, but the growth at the field level compares well. 8 refs., 2 tabs., 9 figs.

Dyayiya et al., Afr J Tradit Complement Altern Med. (2016) 13(1):114 ...

African Journals Online (AJOL)

PROF ADEWUNMI

saponins, tannins and flavonoids while quantitative screenings showed saponins ... Valeriana officinalis extract contains 0.5-2% essential oil (Lacher et al., 2007), ... In 2012, the Department of Science and Technology (DST) and the National ...

Oil and remote communities - Shetland and Orkney

International Nuclear Information System (INIS)

Blackadder, G.A.; Baster, J.

1992-01-01

Due to the advent of the oil industry, the communities of Orkney and Shetland both experienced a period of rapid change in the 1970s, the scale of change being much greater in Shetland reflecting the greater size and range of projects undertaken. However, many of the characteristics of the impact on the two island groups are common. Benefits, particularly in the early years, were higher incomes, low unemployment, more job opportunities, population increase, improved infrastructure and communications. Since 1984, however, unemployment has risen, there are fewer job opportunities and population has declined. Costs and problems to offset against the benefits of the earlier years include uncompetitively high wage rates, a decline in traditional industries, labour and housing shortages, distortion of services and social disruption. Nevertheless, early preparation and planning by the two communities, special legislation to control the development, and policies to deal with subsequent contraction in the industry have enabled the communities to derive some lasting benefits from the experience. These long term benefits include oil revenues, finance for future capital investment and social infrastructure investment. (UK)

Metal working oils. Cutting oils, rolling oils, quenching oils, rust preventive oils; Kinzoku kakoyu. Sessakuyu, atsuenyu, yakiireyu, boseiyu

Energy Technology Data Exchange (ETDEWEB)

Koyama, S. [Idemitsu Kosan Co. Ltd., Tokyo (Japan)

1996-04-01

With the demand against complicating working techniques for a background, foundations of the consideration for each of the lubricants in future are outlined. 1. Cutting oils: From the standpoint of speeding up and fireproofing, share of water-soluble type has come up to 30-40%. In this type, emulsifying dispersants and preservatives are combined. 2. Rolling oils: According to thinning of the standard thickness of steel plates, pressure of contacting surfaces has come up to 300 kg/mm{sup 2}(max.) and slip speed has increased too. In stainless steel plates, in order to get rid of the heat-streak (baking streak originated from wearing-out of oil film) shifting from neat oil to emulsion type is required. 3. Quenching oils: Following two systems are recent tendencies, the mineral oil system having excellent thermostability or the water system containing polyalkylneglycol etc., but the latter is expected from the viewpoint of fireproofing. 4. Rust preventive oils: As this oils do not aim at the rust prevention for long term, degreasing property is required. 20 refs., 5 figs., 1 tab.

Modelling anaerobic codigestion of manure with olive oil mill effluent

DEFF Research Database (Denmark)

Angelidaki, I.; Ellegaard, L.; Ahring, B.K.

1997-01-01

A mathematical model describing the combined anaerobic degradation of complex organic material, such as manure, and a lipid containing additive, such as olive oil mill effluents, has been developed based on a model previously described (Angelidaki et al. 1993). The model has been used to simulate...... anaerobic codigestion of cattle manure together with olive oil mill effluent (OME) and the simulations were compared with experimental data. Simulation data indicated that lack of ammonia, needed as nitrogen source for synthesis of bacterial biomass and as an important pH buffer, could be responsible...

Hydrodeoxygenation of bio-oil using different mesoporous supports of NiMo catalysts

Science.gov (United States)

Rinaldi, Nino; Simanungkalit, Sabar P.; Kristiani, Anis

2017-11-01

Biomass as a renewable and sustainable resources need to utilize in many applications, especially for energy application. One of its energy application is about converting biomass into bio-oil. High oxygen content in bio-oil needs to be upgraded through hydrodeoxygenation process before being used as transportation fuel. The development of heterogenenous catalysts become an important aspect in hydrodeoxygenation process, in particular the upgrading process of bio-oil. Several supporting mesoporous materials, such as TiO2, Al2O3 and MCM-41 have unique properties, both physical and chemical properties that can be utilized in various application, including catalyst. These heterogeneous catalysts were modified their catalytic properties by impregnation with some transition metal. The effect of various supporting material and transition metal impregnated were also studied. Their chemical and physical properties were characterized by X-Ray Diffraction, X-Ray Fluororesence, Fourier Transform Infra-Red, and Surface Area Analyzer. The result of characterizations showed that Ni-Mo/TiO2 is more crystalline than Ni-Mo/MCM-41 and Ni-Mo/Al2O3. In other hand, the specific surface area of Ni-Mo/TiO2 is lower than others. These heterogeneous catalysts were tested their catalytic activity in upgrading bio-oil. The liquid products produced were analyzed by using Elemental Analyzer. The result of catalytic activity tests showed catalysts resulted Ni-Mo/TiO2 exhibits best catalytic activity in hydrodeoxygenation process. The oxygen content decreased significantly from 41.61% to 26.22% by using Ni-Mo/TiO2. Compared with Ni-Mo/TiO2, Ni-Mo/MCM-41 and Ni-Mo/Al2O3 decrease lower to 33.22% % and 28.34%, respectively. Ni-Mo/TiO2 also resulted the highest Deoxygenation Degree (DOD) as of 55% compared with Ni-Mo/MCM-41 and Ni-Mo/Al2O3 as of 31.99 % and 47.99%, respectively.

Nature preservation acceptance model applied to tanker oil spill simulations

DEFF Research Database (Denmark)

Friis-Hansen, Peter; Ditlevsen, Ove Dalager

2003-01-01

is exemplified by a study of oil spills due to simulated tanker collisions in the Danish straits. It is found that the distribution of the oil spill volume per spill is well represented by an exponential distribution both in Oeresund and in Great Belt. When applied in the Poisson model, a risk profile reasonably...... acceptance criterion for the pollution of the environment. This NPWI acceptance criterion is applied to the oil spill example....... be defined in a similar way as the so-called Life Quality Index defined by Nathwani et al [Nathwani JS, Lind NC, Padey MD. Affordable safety by choice: the life quality method. Institute for Risk Research, University of Waterloo; Waterloo (Ontario, Canada):1997], and can be used to quantify the risk...

Adjunctive use of essential oils following scaling and root planing -a randomized clinical trial.

Science.gov (United States)

Azad, Mohammad Fallah; Schwiertz, Andreas; Jentsch, Holger F R

2016-06-07

Hitherto no study has been published on the effect of the adjunctive administration of essential oils following scaling and root planing (SRP). This study describes the effect of a mouthrinse consisting of essential oils (Cymbopogon flexuosus, Thymus zygis and Rosmarinus officinalis) following SRP by clinical and microbiological variables in patients with generalized moderate chronic periodontitis. Forty-six patients (aged 40-65 years) with moderate chronic periodontitis were randomized in a double-blind study and rinsed their oral cavity following SRP with an essential oil mouthrinse (n  =  23) or placebo (n  =  23) for 14 days. Probing depth (PD), attachment level (AL), bleeding on probing (BOP) and modified sulcus bleeding index (SBI) were recorded at baseline and after 3 and 6 months. Subgingival plaque was taken for assessment of major bacteria associated with periodontitis. AL, PD, BOP and SBI were significantly improved in both groups after three (p   essential oils following SRP has a positive effect on clinical variables and on bacterial levels in the subgingival biofilm. 332-12-24092012, DRKS 00009387, German Clinical Trials Register, Freiburg i. Br., 16.09.2015.

Historical evolution of oil painting media: A rheological study

Science.gov (United States)

de Viguerie, Laurence; Ducouret, Guylaine; Lequeux, François; Moutard-Martin, Thierry; Walter, Philippe

2009-09-01

Rheology is the science of flow, which is a phenomenon found in every painting operation, such as decorative paintings or protective coatings. In this article, the principles of rheology as applied to paintings and coatings are recalled in a first part and the rheological criteria required in the paint industry presented. Indeed, different flow behaviours leads to different finishes. The same procedure and techniques as in industry can be employed to explain some evolutions in oil painting aspects over the centuries. The first recipes for oil painting indicate the use of treated oil, resins and spirits. This article deals with the evolution of the composition of these systems as media for oil painting, according to rheological clues. During the Renaissance period, the media used were Newtonian or slightly shear thinning and allowed one a perfect levelling. Then techniques changed, paints became more opaque with less addition of oil/resin media, and brushstrokes appeared visible. Some preparations containing lead, oil and mastic resin, whose flow behaviour is closed to those required in industry, may have appeared during the 17th century and are still used and sold today. To cite this article: L. de Viguerie et al., C. R. Physique 10 (2009).

Agyepong et al., Afr J Tradit Complement Altern Med. (2014) 11(3 ...

African Journals Online (AJOL)

cadewumi

As a result of indiscriminate use of antibiotics in the treatment of these ... been found in the stem bark (Chakraborty et al., 1995), and essential oils including β- ... then powdered using laboratory mill machine (Type 8, Christy and Norris Limited, ...

Herring parasite and tissue alterations following the Exxon Valdez oil spill

International Nuclear Information System (INIS)

Moles, A.D.; Rice, S.D.; Okihiro, M.S.

1993-01-01

The authors examined the intensity and prevalence of larval nematodes (Anisakis simplex) and alterations in selected tissues of spawning Pacific herring (Clupea harengus pallasi) exposed to crude oil, in the laboratory under controlled conditions and in Prince William Sound 14 days after the Exxon Valdez oil spill. In the laboratory, intensity and prevalence of nematodes in the body cavities of herring exposed to the water-soluble fraction of oil declined when exposed to doses above 1.2 mg/L total aromatics. In Prince William Sound, nematodes were rare in spawning herring from oiled sites and abundant among herring from areas outside the spill. Oil exposure apparently induced the nematodes to migrate from the body cavity to the body wall with the lower intensity reflecting a change in parasite location. A coccidian, Eimeria clupearum, was found in greater numbers in oil-exposed herring. To verify exposure effects and to link parasite and tissue alteration with oil exposure, histological examination was used. Liver coagulative necrosis indicated hepatotoxic exposure. Necrosis was followed by macrophage aggregation in the resolution phase. The laboratory exposures allowed confirmation of oil exposure in Prince William Sound and permitted analysis of effects on two internal parasites

Analysis of ZDDP Content and Thermal Decomposition in Motor Oils Using NAA and NMR

Science.gov (United States)

Ferguson, S.; Johnson, J.; Gonzales, D.; Hobbs, C.; Allen, C.; Williams, S.

Zinc dialkyldithiophosphates (ZDDPs) are one of the most common anti-wear additives present in commercially-available motor oils. The ZDDP concentrations of motor oils are most commonly determined using inductively coupled plasma atomic emission spectroscopy (ICP-AES). As part of an undergraduate research project, we have determined the Zn concentrations of eight commercially-available motor oils and one oil additive using neutron activation analysis (NAA), which has potential for greater accuracy and less sensitivity to matrix effects as compared to ICP-AES. The 31P nuclear magnetic resonance (31P-NMR) spectra were also obtained for several oil additive samples which have been heated to various temperatures in order to study the thermal decomposition of ZDDPs.

Synthesis of fatty acid methyl ester from the transesterification of high- and low-acid-content crude palm oil (Elaeis guineensis) and karanj oil (Pongamia pinnata) over a calcium-lanthanum-aluminum mixed-oxides catalyst.

Science.gov (United States)

Syamsuddin, Y; Murat, M N; Hameed, B H

2016-08-01

The synthesis of fatty acid methyl ester (FAME) from the high- and low-acid-content feedstock of crude palm oil (CPO) and karanj oil (KO) was conducted over CaO-La2O3-Al2O3 mixed-oxide catalyst. Various reaction parameters were investigated using a batch reactor to identify the best reaction condition that results in the highest FAME yield for each type of oil. The transesterification of CPO resulted in a 97.81% FAME yield with the process conditions of 170°C reaction temperature, 15:1 DMC-to-CPO molar ratio, 180min reaction time, and 10wt.% catalyst loading. The transesterification of KO resulted in a 96.77% FAME yield with the conditions of 150°C reaction temperature, 9:1 DMC-to-KO molar ratio, 180min reaction time, and 5wt.% catalyst loading. The properties of both products met the ASTM D6751 and EN 14214 standard requirements. The above results showed that the CaO-La2O3-Al2O3 mixed-oxide catalyst was suitable for high- and low-acid-content vegetable oil. Copyright © 2016 Elsevier Ltd. All rights reserved.

MIOR - Microbial Improved Oil Recovery. Basics studies on the suitability of microorganisms for improved oil recovery. Final report; MIOR - Microbial Improved Oil Recovery. Grundlagen der Eignung von Mikroorganismen fuer die Verbesserung der Erdoelgewinnung. Abschlussbericht

Energy Technology Data Exchange (ETDEWEB)

Naeveke, R. [Technische Univ. Braunschweig (Germany). Inst. fuer Mikrobiologie; Fischer, K. [Technische Univ. Braunschweig (Germany). Inst. fuer Mikrobiologie; Timmis, K.N. [Gesellschaft fuer Biotechnologische Forschung mbH, Braunschweig (Germany); Yakimov, M. [Gesellschaft fuer Biotechnologische Forschung mbH, Braunschweig (Germany); Kroeger, A. [Gesellschaft fuer Biotechnologische Forschung mbH, Braunschweig (Germany); Bosecker, K. [Bundesanstalt fuer Geowissenschaften und Rohstoffe, Hannover (Germany); Kruckemeyer, I. [Bundesanstalt fuer Geowissenschaften und Rohstoffe, Hannover (Germany); Mengel-Jung, G. [Bundesanstalt fuer Geowissenschaften und Rohstoffe, Hannover (Germany); Bock, M. [Bundesanstalt fuer Geowissenschaften und Rohstoffe, Hannover (Germany); Schink, B. [Konstanz Univ. (Germany). Fachgebiet Mikrobielle Oekologie; Denger, K. [Konstanz Univ. (Germany). Fachgebiet Mikrobielle Oekologie; Kessel, D. [Institut fuer Erdoel- und Erdgasforschung, Clausthal-Zellerfeld (Germany); Amro, M. [Institut fuer Erdoel- und Erdgasforschung, Clausthal-Zellerfeld (Germany); Jacobs, G. [Institut fuer Erdoel- und Erdgasforschung, Clausthal-Zellerfeld (Germany); Hoffmann, G.G. [Institut fuer Erdoel- und Erdgasforschung, Clausthal-Zellerfeld (Germany); Wagner, M. [Erdoel - Erdgas Gommern GmbH (Germany); Ziran, B. [Erdoel - Erdgas Gommern GmbH (Germany); Nowak, H.U. [Erdoel - Erdgas Gommern GmbH (Germany); Eins, I. [Erdoel - Erdgas Gommern GmbH (Germany); Rosenspiess, K. [Erdoel - Erdgas Gommern GmbH (Germany); Lungershausen, D. [Erdoel - Erdgas Gommern GmbH (Germany)

1996-03-01

Microbial improved oil recovery (MIOR) is the use of microorganisms or microbial products that are injected into the oil reservoir to improve oil flow. The aim of this project was the application of MIOR in case of clastic reservoir rocks of the type encountered typically in Northern Germany. Microorganisms were concentrated, insolated and characterized from samples that were taken from oil production wells, oil processing facilities and soil contaminated with hydrocarbons. More than 500 bacteria strains were investigated for ability to grow under anaerobic conditions, halotolerance, heat tolerance and production of substances that increase viscosity or are surface active. 39 strains were selected for specific tests and genetic investigations. The two bacteria strains Bacillus licheniformis BNP 29 and Sporohalobacter showed to the capable for MIOR. Dynamic flooding experiments were carried out under realistic reservoir conditions, in order to quantify the ability of the microorganisms to mobilize residual oil in place, as well as to investigate the oil mobilizing mechanisms in more detail. It could be shown that the injectivity and migration of the bacteria in porous media are ensured. The microorganisms are able to grow under reservoir conditions as present in oil reservoirs of Northern Germany. Their application in flooding experiments leads to a significant increase of oil recovery. The most important factors influencing the oil recovery are the reduction of the permeability of the reservoir pores and changes in the wettability because of the bacterial growth. A suitable nutrient medium with an acid buffer was developed for the application of MIOR in sandstone reservoirs. An executive summary is prublished in DGMK-Report 441-2/1. (orig.) [Deutsch] MIOR (microbial improved oil recovery)-Verfahren dienen dazu, den Entoelungsgrad einer Erdoellagerstaette durch den gezielten in-situ-Einsatz von geeigneten Mikroorganismen und deren Stoffwechselprodukten zu erhoehen

MIOR - Microbial Improved Oil Recovery. Basic studies on the suitability of microorganisms for improved oil recovery. Executive summary; MIOR - Microbial Improved Oil Recocery. Grundlagen der Eignung von Mikroorganismen fuer die Verbesserung der Erdoelgewinnung. Kurzbericht

Energy Technology Data Exchange (ETDEWEB)

Naeveke, R. [Technische Univ. Braunschweig (Germany). Inst. fuer Mikrobiologie; Timmis, K.N. [Gesellschaft fuer Biotechnologische Forschung mbH, Braunschweig (Germany); Bosecker, K. [Bundesanstalt fuer Geowissenschaften und Rohstoffe, Hannover (Germany); Schink, B. [Konstanz Univ. (Germany). Fachgebiet Mikrobielle Oekologie; Kessel, D. [Institut fuer Erdoel- und Erdgasforschung, Clausthal-Zellerfeld (Germany); Wagner, M. [Erdoel - Erdgas Gommern GmbH (Germany); Tessmer, G. [Deutsche Wissenschaftliche Gesellschaft fuer Erdoel, Erdgas und Kohle e.V., Hamburg (Germany)

1996-03-01

Microbial improved oil recovery (MIOR) is the use of microorganisms or microbial products that are injected into the oil reservoir to improve oil flow. The aim of this project was the application of MIOR in case of clastic reservoir rocks of the type encountered typically in Nothern Germany. Microorganisms were concentrated, isolated and characterized from samples that were taken from oil production wells, oil processing facilities and soil contaminated with hydrocarbons. More than 500 bacteria strains were investigated for ability to grow under anaerobic conditions, halotolerance, heat tolerance and production of substances that increase viscosity or are surface active. 39 strains were selected for specific tests and genetic investigations. The two bacteria strains Bacillus licheniformis BNP 29 and Sporohalobacter showed to the capable for MIOR. Dynamic flooding experiments were carried out under realistic reservoir conditions, in order to quantify the ability of the microorganisms to mobilize residual oil in place, as well as to investigate the oil mobilizing mechanisms in more detail. It could be shown that the injectivity and migration of the bacteria in porous media are ensured. The microorganisms are able to grow under reservoir conditions as present in oil reservoirs of Nothern Germany. Their application in flooding experiments leads to a significant increase of oil recovery. The most important factors influencing the oil recovery are the reduction of the permeability of the reservoir pores and changes in the wettability because of the bacterial growth. A suitable nutrient medium with an acid buffer was developed for the application of MIOR in sandstone reservoirs. (orig.) [Deutsch] MIOR (microbial improved oil recovery)-Verfahren dienen dazu, den Entoelungsgrad einer Erdoellagerstaette durch den gezielten in-situ-Einsatz von geeigneten Mikroorganismen und deren Stoffwechselprodukten zu erhoehen. Ziel des Projektes war es, die Anwendbarkeit von MIOR

Gasoline from biomass through refinery-friendly carbohydrate-based bio-oil produced by ketalization.

Science.gov (United States)

Batalha, Nuno; da Silva, Alessandra V; de Souza, Matheus O; da Costa, Bruna M C; Gomes, Elisa S; Silva, Thiago C; Barros, Thalita G; Gonçalves, Maria L A; Caramão, Elina B; dos Santos, Luciana R M; Almeida, Marlon B B; de Souza, Rodrigo O M A; Lam, Yiu L; Carvalho, Nakédia M F; Miranda, Leandro S M; Pereira, Marcelo M

2014-06-01

The introduction of biomass-derived compounds as an alternative feed into the refinery structure that already exists can potentially converge energy uses with ecological sustainability. Herein, we present an approach to produce a bio-oil based on carbohydrate-derived isopropylidene ketals obtained by reaction with acetone under acidic conditions directly from second-generation biomass. The obtained bio-oil showed a greater chemical inertness and miscibility with gasoil than typical bio-oil from fast pyrolysis. Catalytic upgrading of the bio-oil over zeolites (USY and Beta) yielded gasoline with a high octane number. Moreover, the co-processing of gasoil and bio-oil improved the gasoline yield and quality compared to pure gasoil and also reduced the amount of oxygenated compounds and coke compared with pure bio-oil, which demonstrates a synergistic effect. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Production of hydrogen, liquid fuels, and chemicals from catalytic processing of bio-oils

Science.gov (United States)

Huber, George W; Vispute, Tushar P; Routray, Kamalakanta

2014-06-03

Disclosed herein is a method of generating hydrogen from a bio-oil, comprising hydrogenating a water-soluble fraction of the bio-oil with hydrogen in the presence of a hydrogenation catalyst, and reforming the water-soluble fraction by aqueous-phase reforming in the presence of a reforming catalyst, wherein hydrogen is generated by the reforming, and the amount of hydrogen generated is greater than that consumed by the hydrogenating. The method can further comprise hydrocracking or hydrotreating a lignin fraction of the bio-oil with hydrogen in the presence of a hydrocracking catalyst wherein the lignin fraction of bio-oil is obtained as a water-insoluble fraction from aqueous extraction of bio-oil. The hydrogen used in the hydrogenating and in the hydrocracking or hydrotreating can be generated by reforming the water-soluble fraction of bio-oil.

The future world oil market: state of nature or social contract?

International Nuclear Information System (INIS)

Noel, P.

1999-10-01

Mary Ann Tetreault develops a very interesting interpretation of the emerging new relationship between international oil companies and Middle East producing countries. The original intellectual tools she handles-concepts drawn from the European political philosophy tradition-allow her to argue as follows: (1) the oil market left to itself- whether participants are states or firms-behaves like a Hobbesian ''state of nature'' often resulting in a situation damaging to each participant; (2) to deal with it, the international oil community has historically relied on different types of organisations, but these social contracts or ''republics'' were inherently unstable since they rested on too narrowly defined interests; (3) the rationale behind the possible return of oil companies to the richest Middle East countries is the search for new ''international oil republics'' able to ''offer greater security and higher profits for all the good republicans among them''. (author)

Moderate Baseline Vagal Tone Predicts Greater Prosociality in Children

Science.gov (United States)

Miller, Jonas G.; Kahle, Sarah; Hastings, Paul D.

2016-01-01

Vagal tone is widely believed to be an important physiological aspect of emotion regulation and associated positive behaviors. However, there is inconsistent evidence for relations between children’s baseline vagal tone and their helpful or prosocial responses to others (Hastings & Miller, 2014). Recent work in adults suggests a quadratic association (inverted U-shape curve) between baseline vagal tone and prosociality (Kogan et al., 2014). The present research examined whether this nonlinear association was evident in children. We found consistent evidence for a quadratic relation between vagal tone and prosociality across 3 samples of children using 6 different measures. Compared to low and high vagal tone, moderate vagal tone in early childhood concurrently predicted greater self-reported prosociality (Study 1), observed empathic concern in response to the distress of others and greater generosity toward less fortunate peers (Study 2), and longitudinally predicted greater self-, mother-, and teacher-reported prosociality 5.5 years later in middle childhood (Study 3). Taken together, our findings suggest that moderate vagal tone at rest represents a physiological preparedness or tendency to engage in different forms of prosociality across different contexts. Early moderate vagal tone may reflect an optimal balance of regulation and arousal that helps prepare children to sympathize, comfort, and share with others. PMID:27819463

Essential oil of Hexalobus monopetalus (A. Rich) Engl. leaves from Benin : a new source of citral

NARCIS (Netherlands)

Leclercq, P.A.; Ayedoun, M.A.; Sossou, P.V.; Houngnon, P.

1997-01-01

The leaf oil of Hexalobus monopetalus (Annonaceae) from Benin was analyzed by high resolution GC and GC/MS. Forty components were identified, representing more than 95% of the oiL The main constituents were geranial (37,9'lAl), neral (30,9%), linalool (35%), (E)-anethole (2.6%), selin-ll-en-4a-ol

Exploring the core factors and its dynamic effects on oil price: An application on path analysis and BVAR-TVP model

International Nuclear Information System (INIS)

Chai Jian; Guo, Ju-E.; Meng Lei; Wang Shouyang

2011-01-01

As the uncertainty of oil price increases, impacts of the influential factors on oil price vary over time. It is of great importance to explore the core factors and its time-varying influence on oil price. In view of this, based on the PATH-ANALYSIS model, this paper obtains the core factors, builds an oil price system VAR model, which uses demand, supply, price, and inventory as endogenous variables, and China's net imports as well as dollar index as exogenous variables. Then we set up a BVAR-TVP (Time varying parameter) model to analyze dynamic impacts of core factors on oil price. The results show that: (1) oil prices became more sensitive to oil supply changes, and the influence delays became shorter; (2) the impact of oil inventories on oil prices with a time lag of two quarters but has a downward trend; (3) the impact of oil consumption on oil prices with a time lag of two quarters, and this effect is increasingly greater; (4) the US dollar index is always the important factor of oil price and its control power increases gradually, and the financial crisis (occurred in 2008) further strengthens the influence of US dollar. - Highlights: ► We build an oil price VAR model based on the PATH-ANALYSIS results. ► The dynamic effects of core factors on oil price was studied by BVAR-TVP model. ► Oil prices became more sensitive to oil supply changes. ► The effect of oil consumption on oil prices is increasingly greater. ► Financial crisis further strengthens the influence of US dollar on oil price.

Oxidative regeneration of Ni-Mo-gamma-Al/sub 2/O/sub 3/ catalysts used for hydrotreatment of coal-derived oil

Energy Technology Data Exchange (ETDEWEB)

Yoshimura, Yuji; Furimsky, Edward; Sato, Toshio; Shimada, Hiromichi; Matsubayashi, Nobuyuki; Nishijima, Akio

1986-10-23

In order to easily find the oxidative reaction characteristics of carbonaceous materials and sulfur deposited on the catalysts used for hydrogenation, oxidative regeneration behavior as studied with a fixed bed reactor, and the surfaces of the spent catalysts were analyzed by XPS to find the changes in form of active metals and sulfur on the catalysts. Ni-Mo-gamma-Al/sub 2/O/sub 3/ catalysts were used for hydrotreatment of primary coal-derived oil from Morwell coal. The spent catalysts were extracted by THF, dried and crushed into 100-200 mesh powder. The relation between catalyst regeneration temperature and CO/sub 2/ or SO/sub 2/, the relation between generated gas compositions and temperature in regeneration, and the activation energy of carbon and sulfur in the catalysts for oxidative reaction were indicated with data. As a result, it was found that a part of the active metals turned to sulfates by hydrotreatment and the residual sulfur existed in form of sulfate. ( 6 figs, 2 tabs, 4 refs )

Effect of frying oils on quality characteristics of frozen chicken patties ...

African Journals Online (AJOL)

Shaista

2012-02-09

Feb 9, 2012 ... products that have negative effects on human health. (Boyd et al., 1993). ... Cumin powder - 2 g, Coriander powder - 2 g and salt – to taste) for ..... Effect of dietary palm olein oil on oxidative stress associated with ischemic-.

Underwater sound and vibrations due to oil & gas activities

NARCIS (Netherlands)

Beek, P.J.G. van; Binnerts, B.; Nennie, E.D.; Benda-Beckmann, A.M. von

2014-01-01

In the oil & gas industry there is a trend towards more subsea activities. To improve gas recovery from existing and new fields at greater depths, the produced gas will be compressed, processed and transported via subsea templates and underwater networks (pipelines, flexible risers, etc.). Besides

High quality bio-oil from catalytic flash pyrolysis of lignocellulosic biomass over alumina-supported sodium carbonate

KAUST Repository

Imran, Ali

2014-11-01

Performance of a novel alumina-supported sodium carbonate catalyst was studied to produce a valuable bio-oil from catalytic flash pyrolysis of lignocellulosic biomass. Post treatment of biomass pyrolysis vapor was investigated in a catalyst fixed bed reactor at the downstream of the pyrolysis reactor. In-situ catalytic upgrading of biomass pyrolysis vapor was conducted in an entrained flow pyrolysis reactor by feeding a premixed feedstock of the catalyst and biomass. Na2CO3/gamma-Al2O3 was very effective for de-oxygenation of the pyrolysis liquid and oxygen content of the bio-oil was decreased from 47.5 wt.% to 16.4 wt.%. An organic rich bio-oil was obtained with 5.8 wt.% water content and a higher heating value of 36.1 MJ/kg. Carboxylic acids were completely removed and the bio-oil had almost a neutral pH. This bio-oil of high calorific low, low water and oxygen content may be an attractive fuel precursor. In-situ catalytic upgrading of biomass pyrolysis vapor produced a very similar quality bio-oil compared to post treatment of pyrolysis vapors, and shows the possible application of Na2CO3/gamma-Al2O3 in a commercial type reactor system such as a fluidized bed reactor. (C) 2014 Elsevier B.V. All rights reserved.

Para rubber seed oil: new promising unconventional oil for cosmetics.

Science.gov (United States)

Lourith, Nattaya; Kanlayavattanakul, Mayuree; Sucontphunt, Apirada; Ondee, Thunnicha

2014-01-01

Para rubber seed was macerated in petroleum ether and n-hexane, individually, for 30 min. The extraction was additionally performed by reflux and soxhlet for 6 h with the same solvent and proportion. Soxhlet extraction by petroleum ether afforded the greatest extractive yield (22.90 ± 0.92%). Although antioxidant activity by means of 1, 1-diphenyl-2-picrylhydrazyl (DPPH) assay was insignificantly differed in soxhleted (8.90 ± 1.15%) and refluxed (9.02 ± 0.71%) by n-hexane, soxhlet extraction by n-hexane was significantly (p < 0.05) potent scavenged 2,2'-azino-bis(3-ethylbenzothaiazoline)-6-sulfonic acid) or ABTS radical with trolox equivalent antioxidant capacity (TEAC) of 66.54 ± 6.88 mg/100 g oil. This extract was non cytotoxic towards normal human fibroblast cells. In addition, oleic acid and palmitic acid were determined at a greater content than in the seed of para rubber cultivated in Malaysia, although linoleic and stearic acid contents were not differed. This bright yellow extract was further evaluated on other physicochemical characters. The determined specific gravity, refractive index, iodine value, peroxide value and saponification value were in the range of commercialized vegetable oils used as cosmetic raw material. Therefore, Para rubber seed oil is highlighted as the promising ecological ingredient appraisal for cosmetics. Transforming of the seed that is by-product of the important industrial crop of Thailand into cosmetics is encouraged accordingly.

Oil vulnerability index of oil-importing countries

International Nuclear Information System (INIS)

Gupta, Eshita

2008-01-01

This paper assesses the relative oil vulnerability of 26 net oil-importing countries for the year 2004 on the basis of various indicators - the ratio of value of oil imports to gross domestic product (GDP), oil consumption per unit of GDP, GDP per capita and oil share in total energy supply, ratio of domestic reserves to oil consumption, exposure to geopolitical oil market concentration risks as measured by net oil import dependence, diversification of supply sources, political risk in oil-supplying countries, and market liquidity. The approach using the principal component technique has been adopted to combine these individual indicators into a composite index of oil vulnerability. Such an index captures the relative sensitivity of various economies towards developments of the international oil market, with a higher index indicating higher vulnerability. The results show that there are considerable differences in the values of individual indicators of oil vulnerability and overall oil vulnerability index among the countries (both inter and intraregional). (author)

Oil vulnerability index of oil-importing countries

Energy Technology Data Exchange (ETDEWEB)

Gupta, Eshita [The Energy and Resources Institute, Darbari Seth Block, Habitat Place, New Delhi 110 003 (India)

2008-03-15

This paper assesses the relative oil vulnerability of 26 net oil-importing countries for the year 2004 on the basis of various indicators - the ratio of value of oil imports to gross domestic product (GDP), oil consumption per unit of GDP, GDP per capita and oil share in total energy supply, ratio of domestic reserves to oil consumption, exposure to geopolitical oil market concentration risks as measured by net oil import dependence, diversification of supply sources, political risk in oil-supplying countries, and market liquidity. The approach using the principal component technique has been adopted to combine these individual indicators into a composite index of oil vulnerability. Such an index captures the relative sensitivity of various economies towards developments of the international oil market, with a higher index indicating higher vulnerability. The results show that there are considerable differences in the values of individual indicators of oil vulnerability and overall oil vulnerability index among the countries (both inter and intraregional). (author)

Extruded linseed and linseed oil as alternative to soybean meal and soybean oil in diets for fattening lambs

Directory of Open Access Journals (Sweden)

Anna Caputi Jambrenghi

2010-01-01

Full Text Available The study evaluated the effects of replacing soybean meal and soybean oil respectively with extruded linseed and linseed oil on the productive performances and meat quality traits in lambs slaughtered at 90 days. Lambs weaned at 40 days were divided into 3 groups (N.=10 fed ad libitum for 6 weeks as follows: C (control, commercial feed containing soybean meal and soybean oil; LO (feed containing linseed oil instead of soybean oil; EL (feed containing extruded linseed. Meat quality traits were evaluated on the Longissimus lumborum (Ll and Semimembranosus (Sm muscles. The lambs’ growth performances and the slaughtering and sectioning data did not differ between groups. The redness of meat was significantly higher (P<0.05 for the LO and EL groups compared to the control for both the muscles tested. Ll meat samples of the EL group showed a greater cooking loss compared to LO (P<0.01 and to the control (P<0.05. The amount of linoleic acid in raw Ll meat samples was significantly (P<0.01 lower in both LO and EL groups with respect to control. The concentration of α-linolenic acid was significantly (P<0.01 higher in the EL group and this positively affected the total content of ω3 as well as the ω6/ω3 ratio.

Single-cultivar extra virgin olive oil classification using a potentiometric electronic tongue.

Science.gov (United States)

Dias, Luís G; Fernandes, Andreia; Veloso, Ana C A; Machado, Adélio A S C; Pereira, José A; Peres, António M

2014-10-01

Label authentication of monovarietal extra virgin olive oils is of great importance. A novel approach based on a potentiometric electronic tongue is proposed to classify oils obtained from single olive cultivars (Portuguese cvs. Cobrançosa, Madural, Verdeal Transmontana; Spanish cvs. Arbequina, Hojiblanca, Picual). A meta-heuristic simulated annealing algorithm was applied to select the most informative sets of sensors to establish predictive linear discriminant models. Olive oils were correctly classified according to olive cultivar (sensitivities greater than 97%) and each Spanish olive oil was satisfactorily discriminated from the Portuguese ones with the exception of cv. Arbequina (sensitivities from 61% to 98%). Also, the discriminant ability was related to the polar compounds contents of olive oils and so, indirectly, with organoleptic properties like bitterness, astringency or pungency. Therefore the proposed E-tongue can be foreseen as a useful auxiliary tool for trained sensory panels for the classification of monovarietal extra virgin olive oils. Copyright © 2014 Elsevier Ltd. All rights reserved.

Hydrotreatment of heavy oil from coal liquefaction on Sulfide Ni - W Catalysts

Energy Technology Data Exchange (ETDEWEB)

Zhi-ping Lei; Li-juan Gao; Heng-fu Shui; Shi-biao, Ren; Zhi-cai Wang; Kang-shi Gang, E-mail: shhf@ahut.edu.c [Anhui University of Technology, Maanshan (China). School of Chemistry and Chemical Engineering. Anhui Key Lab. of Coal Clean Conversion and Utilization

2011-07-01

Heavy oil (distillation temperature: 320-340 deg C) derived from the direct coal liquefaction process using Shengli coal were hydrotreated using sulfided Ni-Mo/Al{sub 2}O{sub 3}, Ni-W/Al{sub 2}O{sub 3}, and Ni-W/SiO{sub 2} catalysts respectively. The sulfided catalysts were characterized by BET, XRD, H{sub 2}-TPR and NH{sub 3}-TPD respectively. The evaluations of the hydrodenitrogenation (HDN) and hydrodearomatization (HDA) properties of heavy oil on the three catalysts were carried out at 400 deg C and 5.0 MPa initial H2 pressure. The W-based catalysts displayed better performances than Mo-based catalysts for the HDN and HDA reactions. Al{sub 2}O{sub 3} supported catalysts were found to have higher catalytic activities than on SiO{sub 2} supported ones. The activities of sulfided catalysts were associated mainly with the nature of active sites, acidity, metal sulfide crystallite size and the amount of the reducible sulfur species of metal sulfide. (author)

Giant Oil Fields - The Highway to Oil: Giant Oil Fields and their Importance for Future Oil Production

International Nuclear Information System (INIS)

Robelius, Fredrik

2007-01-01

Since the 1950s, oil has been the dominant source of energy in the world. The cheap supply of oil has been the engine for economic growth in the western world. Since future oil demand is expected to increase, the question to what extent future production will be available is important. The belief in a soon peak production of oil is fueled by increasing oil prices. However, the reliability of the oil price as a single parameter can be questioned, as earlier times of high prices have occurred without having anything to do with a lack of oil. Instead, giant oil fields, the largest oil fields in the world, can be used as a parameter. A giant oil field contains at least 500 million barrels of recoverable oil. Only 507, or 1 % of the total number of fields, are giants. Their contribution is striking: over 60 % of the 2005 production and about 65 % of the global ultimate recoverable reserve (URR). However, giant fields are something of the past since a majority of the largest giant fields are over 50 years old and the discovery trend of less giant fields with smaller volumes is clear. A large number of the largest giant fields are found in the countries surrounding the Persian Gulf. The domination of giant fields in global oil production confirms a concept where they govern future production. A model, based on past annual production and URR, has been developed to forecast future production from giant fields. The results, in combination with forecasts on new field developments, heavy oil and oil sand, are used to predict future oil production. In all scenarios, peak oil occurs at about the same time as the giant fields peak. The worst-case scenario sees a peak in 2008 and the best-case scenario, following a 1.4 % demand growth, peaks in 2018

Numerical studies of spray combustion processes of palm oil biodiesel and diesel fuels using reduced chemical kinetic mechanisms

KAUST Repository

Kuti, Olawole; Sarathy, Mani; Nishida, Keiya; Roberts, William L.

2014-01-01

Spray combustion processes of palm oil biodiesel (PO) and conventional diesel fuels were simulated using the CONVERGE CFD code. Thermochemical and reaction kinetic data (115 species and 460 reactions) by Luo et al. (2012) and Lu et al. (2009) (68

Geochemistry and habitat of the oils in Italy

Energy Technology Data Exchange (ETDEWEB)

Mattavelli, L.; Novelli, L. (Agip S.p.A., Milano (Italy))

1990-10-01

All varieties of liquid petroleum, ranging from condensates (> 50{degree}API) to immature sulfur-rich heavy oils (as low as 5{degree} API), have been found in Italy. However, nonbiodegraded heavy oils account for about 70% of the total original oil in place. Geochemical analyses indicate that 11 oil groups are present in the Italian basins and two main types of source rocks have been identified: Triassic carbonates and Tertiary shales. About 95% of the oils were originated from Middle and Upper Triassic carbonates containing type II kerogen (about 1% total organic carbon (TOC) and 500 mg hydrocarbon/g TOC). Only a relatively minor amount of oil was generated by Tertiary shales containing type III kerogen with TOC generally less than 1%. Timing of generation and migration and bulk properties of oils were controlled by geodynamic histories of the three main Italian geologic settings: (1) Apennine and Southern Alp thrust belts, (2) foredeep (depression bordering the thrust belts), and (3) foreland (nondeformed African continental margin). Within the Apennine thrust belts, deep burial during the Neogene resulted in the generation of substantially lighter oils, not only from deeply buried Triassic but sometimes also from Tertiary source rocks. In the late Neogene, foredeep depocenters located in the central Adriatic and southern Sicily, high subsidence (up to 1,000 m/m.y.), a low geothermal gradient (22C/km) and compressional tectonics caused the generation of immature heavy oils generally at depths below 5,000 m and temperatures greater than 100C. Rapid burial and higher geothermal gradients (32C/km), which occurred since the Jurassic, resulted in the generation of light oils from the Late Cretaceous to the Oligocene in the southern sector of Adriatic foreland.

An evaluation of known remaining oil resources in the state of Kansas: Project on advanced oil recovery and the states. Volume 4

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-11-01

The Interstate Oil and Gas Compact Commission (IOGCC) has conducted a series of studies to evaluate the known, remaining oil resource in twenty-three (23) states. The primary objective of die IOGCC`s effort is to examine the potential impact of an aggressive and focused program of research, development, and demonstration (RD&D) and technology transfer on future oil recovery in the United States. As part of a larger effort by the IOGCC, this report focuses on the potential economic benefits of improved oil recovery in the state of Kansas. Individual reports for seven other oil producing states and a national report have been separately published by the IOGCC. Several major technical insights for state and Federal policymakers and regulators can be reached from this analysis. Overall, well abandonments and more stringent environmental regulations could limit economic access to the nation`s known, remaining oil resource. The high risk of near-term abandonment and the significant benefits of future application of improved oil recovery technoloy, clearly point to a need for more aggressive transfer of currently available technologies to domestic oil producers. Development and application of advanced oil recovery technologies could leave even greater benefits to the nation. A collaborative, focused RD&D effort, integrating the resources and expertise of industry, state and local governments, and the Federal government, is clearly warranted. With effective RD&D and a program of aggressive technology transfer to widely disseminate its results, Kansas oil production could be maximized. The resulting increase in production rates, employment, operator profits, state and Federal tax revenues, energy security will benefit the state of Kansas and the nation as a whole.

An evaluation of known remaining oil resources in the state of Louisiana: Project on advanced oil recovery and the states. Volume 5

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-11-01

The Interstate Oil and Gas Compact Commission (IOGCC) has conducted a series of studies to evaluate the known, remaining oil resource in twenty-three (23) states. The primary objective of die IOGCC`s effort is to examine the potential impact of an aggressive and focused program of research, development, and demonstration (RD&D) and technology transfer on future oil recovery in the United States. As part of a larger effort by the IOGCC, this report focuses on the potential economic benefits of improved oil recovery in the state of Louisiana. Individual reports for seven other oil producing states and a national report have been separately published by the IOGCC. Several major technical insights for state and Federal policymakers and regulators can be reached from this analysis. Overall, well abandonments and more stringent environmental regulations could limit economic access to the nation`s known, remaining oil resource. The high risk of near-term abandonment and the significant benefits of future application of improved oil recovery technoloy, clearly point to a need for more aggressive transfer of currently available technologies to domestic oil producers. Development and application of advanced oil recovery technologies could leave even greater benefits to the nation. A collaborative, focused RD&D effort, integrating the resources and expertise of industry, state and local governments, and the Federal government, is clearly warranted. With effective RD&D and a program of aggressive technology transfer to widely disseminate its results, Louisiana oil production could be maximized. The resulting increase and improvement in production rates, employment, operator profits, state and Federal tax revenues, energy security will benefit both the state of Louisiana and the nation as a whole.

Upgrading of the liquid fuel from fast pyrolysis of biomass over MoNi/{gamma}-Al{sub 2}O{sub 3} catalysts

Energy Technology Data Exchange (ETDEWEB)

Xu, Ying; Liang, Wei [Guangzhou Institute of Energy Conversion, Chinese Academy of Sciences, Guangzhou, Guangdong (China); Graduate School of the Chinese Academy of Sciences, Beijing (China); Wang, Tiejun; Ma, Longlong; Zhang, Qi [Guangzhou Institute of Energy Conversion, Chinese Academy of Sciences, Guangzhou, Guangdong (China); Key Laboratory of Renewable Energy and Gas Hydrate, Chinese Academy of Sciences, Guangzhou, Guangdong (China)

2010-09-15

The hydrotreatment of bio-oil, which obtained from fast pyrolysis of pine sawdust, was investigated over MoNi/{gamma}-Al{sub 2}O{sub 3} catalyst under mild conditions (373 K, 3 MPa hydrogen pressure). Acetic acid was taken as a model compound to investigate the effects of Mo promoter contents and reducing temperatures of catalysts on the catalysts activity under the condition of 473 K and 3 MPa hydrogen pressure. X-ray diffraction and temperature programmed reduction showed that the addition of Mo promoter benefited the uniformity of nickel species and inhibited the formation of NiAl{sub 2}O{sub 4} spinel in the catalysts. The GC spectrum of liquid products showed the mechanism of the model reaction. The maximum conversion of acetic acid (33.20%) was attained over 0.06MoNi/{gamma}-Al{sub 2}O{sub 3} catalysts being reduced at 873 K. This catalyst was chosen for the upgrading of raw bio-oil. After the upgrading process, the pH value of the bio-oil increased from 2.33 to 2.77. The water content increased from 35.52 wt.% to 41.55 wt.% and the gross calorific value increased from 13.96 MJ/kg to 14.17 MJ/kg. The hydrogen content in the bio-oil increased from 6.25 wt.% to 6.95 wt.%. The product properties of the upgraded bio-oil, particularly the hydrogen content and the acidity were considerably improved. The results of gas chromatography-mass spectrometry analysis showed that both hydrotreatment and esterification had happened over 0.06MoNi/{gamma}-Al{sub 2}O{sub 3} (873) catalyst during the upgrading process. (author)

Oil risk in oil stocks

NARCIS (Netherlands)

Scholtens, Bert; Wang, L

2008-01-01

We assess the oil price sensitivities and oil risk premiums of NYSE listed oil & gas firms' returns by using a two-step regression analysis under two different arbitrage pricing models. Thus, we apply the Fama and French (1992) factor returns in a study of oil stocks. In all, we find that the return

Effects of catalytic hydrotreating on light cycle oil fuel quality

International Nuclear Information System (INIS)

Anabtawi, J.A.; Ali, S.A.

1991-01-01

This paper reports on a pilot plant study that was conducted to evaluate three commercial catalysts for hydrotreating of light cycle oil to reduce its aromatic content and improve the cetane index. The operating parameters were varied between 325 and 400 degrees C, 1 and 3 h - 1 , and 4 and 10 MPa at 535 L/L. The data showed that, in general, the product density and aromatic content decreased as the temperature or pressure increased or space velocity decreased. The cetane index improvement ranged from 7.3 to 10.0 for the Ni-W/Al 2 O 3 catalyst and from 6.1 to 10.1 for the Ni-Mo/Al 2 O 3 catalysts. The catalyst performance was evaluated in terms of hydrodesulfurization, hydrodenitrogenation, hydrogenation, aromatic saturation, and hydrogen consumption. This study confirms that light cycle oil can be hydrotreated to improve its cetane quality, thus increasing the extent of its blending ratio into the diesel pool

ALS patients' regulatory T lymphocytes are dysfunctional, and correlate with disease progression rate and severity.

Science.gov (United States)

Beers, David R; Zhao, Weihua; Wang, Jinghong; Zhang, Xiujun; Wen, Shixiang; Neal, Dan; Thonhoff, Jason R; Alsuliman, Abdullah S; Shpall, Elizabeth J; Rezvani, Katy; Appel, Stanley H

2017-03-09

Neuroinflammation is a pathological hallmark of ALS in both transgenic rodent models and patients, and is characterized by proinflammatory T lymphocytes and activated macrophages/microglia. In ALS mouse models, decreased regulatory T lymphocytes (Tregs) exacerbate the neuroinflammatory process, leading to accelerated motoneuron death and shortened survival; passive transfer of Tregs suppresses the neuroinflammation and prolongs survival. Treg numbers and FOXP3 expression are also decreased in rapidly progressing ALS patients. A key question is whether the marked neuroinflammation in ALS can be attributed to the impaired suppressive function of ALS Tregs in addition to their decreased numbers. To address this question, T lymphocyte proliferation assays were performed. Compared with control Tregs, ALS Tregs were less effective in suppressing responder T lymphocyte proliferation. Although both slowly and rapidly progressing ALS patients had dysfunctional Tregs, the greater the clinically assessed disease burden or the more rapidly progressing the patient, the greater the Treg dysfunction. Epigenetically, the percentage methylation of the Treg-specific demethylated region was greater in ALS Tregs. After in vitro expansion, ALS Tregs regained suppressive abilities to the levels of control Tregs, suggesting that autologous passive transfer of expanded Tregs might offer a novel cellular therapy to slow disease progression.

ALS patients’ regulatory T lymphocytes are dysfunctional, and correlate with disease progression rate and severity

Science.gov (United States)

Beers, David R.; Zhao, Weihua; Wang, Jinghong; Zhang, Xiujun; Wen, Shixiang; Neal, Dan; Thonhoff, Jason R.; Alsuliman, Abdullah S.; Shpall, Elizabeth J.; Rezvani, Katy

2017-01-01

Neuroinflammation is a pathological hallmark of ALS in both transgenic rodent models and patients, and is characterized by proinflammatory T lymphocytes and activated macrophages/microglia. In ALS mouse models, decreased regulatory T lymphocytes (Tregs) exacerbate the neuroinflammatory process, leading to accelerated motoneuron death and shortened survival; passive transfer of Tregs suppresses the neuroinflammation and prolongs survival. Treg numbers and FOXP3 expression are also decreased in rapidly progressing ALS patients. A key question is whether the marked neuroinflammation in ALS can be attributed to the impaired suppressive function of ALS Tregs in addition to their decreased numbers. To address this question, T lymphocyte proliferation assays were performed. Compared with control Tregs, ALS Tregs were less effective in suppressing responder T lymphocyte proliferation. Although both slowly and rapidly progressing ALS patients had dysfunctional Tregs, the greater the clinically assessed disease burden or the more rapidly progressing the patient, the greater the Treg dysfunction. Epigenetically, the percentage methylation of the Treg-specific demethylated region was greater in ALS Tregs. After in vitro expansion, ALS Tregs regained suppressive abilities to the levels of control Tregs, suggesting that autologous passive transfer of expanded Tregs might offer a novel cellular therapy to slow disease progression. PMID:28289705

An evaluation of known remaining oil resources in the state of California. Volume 2, Project on Advanced Oil Recovery and the States

International Nuclear Information System (INIS)

1994-10-01

The Interstate Oil and Gas Compact Commission (IOGCC) has conducted a series of studies to evaluate the known, remaining oil resource in twenty-three (23) states. The primary objective of the IOGCC's effort is to examine the potential impact of an aggressive and focused program of research, development, and demonstration (RD ampersand D) and technology transfer on future oil recovery in the United States. As a part of this larger effort by the IOGCC, this report focuses on the potential economic benefits of improved oil recovery in the state of California. Individual reports for seven other oil producing states and a national report have been separately published by the IOGCC. The analysis presented in this report is based on the databases and models available in the Tertiary Oil Recovery Information System (TORIS). Overall, well abandonments and more stringent environmental regulations could limit economic access to California's known, remaining oil resource. The high risk of near-term abandonment and the significant benefits of future application of improved oil recovery technology, clearly point to a need for more aggressive transfer of currently available technologies to oil producers. Development and application of advanced oil recovery technologies could have even greater benefits to the state and the nation. A collaborative, focused RD ampersand D effort, integrating the resources and expertise of industry, state and local governments, and the Federal government, is clearly warranted. With effective RD ampersand D and a program of aggressive technology transfer to widely disseminate its results, California oil production could be maximized. The resulting increase in production rates, employment, operator profits, state and Federal tax revenues, and energy security will benefit both the state of California and the nation as a whole

Influence of alumina oxide nanoparticles on the performance and emissions in a methyl ester of neem oil fuelled direct injection diesel engine

Directory of Open Access Journals (Sweden)

Balaji Gnanasikamani

2017-01-01

Full Text Available The experimental investigation of the influence of Al2O3 nanoadditive on performance and emissions in a methyl ester of neem oil fueled direct injection Diesel engine is reported in this paper. The Al2O3 nanoparticles are mixed in various proportions (100 to 300 ppm with methyl ester of neem oil. The performance and emissions are tested in a single cylinder computerized, 4-stroke, stationary, water-cooled Diesel engine of 3.5 kW rated power. Results show that the nanoadditive is effective in increasing the performance and controlling the NO emissions of methyl ester of neem oil fueled Diesel engines.

The self-prescribed use of aromatherapy oils by pregnant women.

Science.gov (United States)

Sibbritt, David W; Catling, Christine J; Adams, Jon; Shaw, Andrea J; Homer, Caroline S E

2014-03-01

While some studies have reported effectiveness of aromatherapy oils use during labour there is no reported evidence of efficacy or risks of aromatherapy oils use for pregnancy-related symptoms or conditions. A number of aromatherapy oils are unsafe for use by pregnant women yet there is currently no research examining the prevalence and characteristics of women who use aromatherapy oils during pregnancy. To conduct an empirical study of the prevalence and characteristics of women who use aromatherapy oils during pregnancy. The research was conducted as part of the Australian Longitudinal Study on Women's Health (ALSWH), focusing on the nationally representative sample of Australian women aged 31-36 years. Data were collected via a cross-sectional questionnaire (n=8200) conducted in 2009. Self-prescribed aromatherapy oils were used by 15.2% of pregnant women. Pregnant women were 1.57 (95% CI: 1.01, 2.43) times more likely to self-prescribe use of aromatherapy oils if they have allergies or hayfever, and 2.26 (95% CI: 1.34, 3.79) times more likely to self-prescribe use of aromatherapy oils if they have a urinary tract infection (UTI). Our study highlights a considerable use of aromatherapy oils by pregnant women. There is a clear need for greater communication between practitioners and patients regarding the use of aromatherapy oils during pregnancy, as well a need for health care practitioners to be mindful that pregnant women in their care may be using aromatherapy oils, some of which may be unsafe. Copyright © 2013 Australian College of Midwives. Published by Elsevier Ltd. All rights reserved.

The asymmetric effects of oil price and monetary policy shocks. A nonlinear VAR approach

International Nuclear Information System (INIS)

Rahman, Sajjadur; Serletis, Apostolos

2010-01-01

In this paper we investigate the asymmetric effects of oil price shocks and monetary policy on macroeconomic activity, using monthly data for the United States, over the period from 1983:1 to 2008:12. In doing so, we use a logistic smooth transition vector autoregression (VAR), as detailed in Terasvirta and Anderson (1992) and Weise (1999), and make a distinction between two oil price volatility regimes (high and low), using the realized oil price volatility as a switching variable. We isolate the effects of oil price and monetary policy shocks and their asymmetry on output growth and, following Koop et al. (1996) and Weise (1999), we employ simulation methods to calculate Generalized Impulse Response Functions (GIRFs) to trace the effects of independent shocks on the conditional means of the variables. Our results suggest that in addition to the price of oil, oil price volatility has an impact on macroeconomic activity and that monetary policy is not only reinforcing the effects of oil price shocks on output, it is also contributing to the asymmetric response of output to oil price shocks. (author)

The asymmetric effects of oil price and monetary policy shocks. A nonlinear VAR approach

Energy Technology Data Exchange (ETDEWEB)

Rahman, Sajjadur [Department of Economics, University of Saskatchewan, Saskatoon (Canada); Serletis, Apostolos [Department of Economics, University of Calgary, Calgary (Canada)

2010-11-15

In this paper we investigate the asymmetric effects of oil price shocks and monetary policy on macroeconomic activity, using monthly data for the United States, over the period from 1983:1 to 2008:12. In doing so, we use a logistic smooth transition vector autoregression (VAR), as detailed in Terasvirta and Anderson (1992) and Weise (1999), and make a distinction between two oil price volatility regimes (high and low), using the realized oil price volatility as a switching variable. We isolate the effects of oil price and monetary policy shocks and their asymmetry on output growth and, following Koop et al. (1996) and Weise (1999), we employ simulation methods to calculate Generalized Impulse Response Functions (GIRFs) to trace the effects of independent shocks on the conditional means of the variables. Our results suggest that in addition to the price of oil, oil price volatility has an impact on macroeconomic activity and that monetary policy is not only reinforcing the effects of oil price shocks on output, it is also contributing to the asymmetric response of output to oil price shocks. (author)

Winter distribution and oiling of common terns in Trinidad: A further look

Science.gov (United States)

Erwin, R.M.; Smith, G.J.; Clapp, R.B.

1986-01-01

Common Terns were studied during January and March 1985 in Trinidad as part of wintering terns in Latin America. Eighty-nine birds were captured, 33 in January, 56 in March. Terns averaged 102 .+-. 0.9 g, with March birds weighing more than those caught in January. This weight is similar to that reported earlier by Blokpoel et al. (1982, 1984) and is considerably less than weights of either premigratory immature or adult Common Terns. Terns in Trinidad appear to be opportunistic, using human fishing for their food source and roosting on boats, oil platforms and other man-made structures. One-half of the captured sample of birds had at least detectable amounts of oil on the plumage. This represents the highest frequency of oiling reported yet for any seabird living under 'baseline' (non-spill) conditions in North or Central America. Oiling had no apparent major effect on the condition of birds since oiled birds had similar weights and blood parameters when compared to unoiled birds.

The future world oil market: state of nature or social contract?

Energy Technology Data Exchange (ETDEWEB)

Noel, P

1999-10-01

Mary Ann Tetreault develops a very interesting interpretation of the emerging new relationship between international oil companies and Middle East producing countries. The original intellectual tools she handles-concepts drawn from the European political philosophy tradition-allow her to argue as follows: (1) the oil market left to itself- whether participants are states or firms-behaves like a Hobbesian ''state of nature'' often resulting in a situation damaging to each participant; (2) to deal with it, the international oil community has historically relied on different types of organisations, but these social contracts or ''republics'' were inherently unstable since they rested on too narrowly defined interests; (3) the rationale behind the possible return of oil companies to the richest Middle East countries is the search for new ''international oil republics'' able to ''offer greater security and higher profits for all the good republicans among them''. (author)

Using the transformer oil-based nanofluid for cooling of power distribution transformer