PBF task and training requirements analysis

International Nuclear Information System (INIS)

Blackman, H.S.; Gertman, D.I.; Petersen, R.J.

1983-05-01

Task analyses were used to assist in identifying improvements needed in the training curriculum for selected positions at the Power Burst Facility (PBF). Four positions were examined: Experiment Power Reactor Operator, Experiment (EPRO-Ex); Experiment Power Reactor Operator, Plant (EPRO-P); Experiment Power Reactor Operator, Console (EPRO-Co), and Shift Supervisor (SS). A complete position task listing and core of tasks defined in terms of (a) level of difficulty to perform, (b) severity of consequence if performed improperly, and (c) associated error probability were identified by each position. The systems, academic, and administrative knowledge needed by job incumbents to perform each task was noted. Strategies for teaching the knowledge associated with these tasks are presented

Workability of glass reinforced concrete (GRC) with granite and silica sand aggregates

Science.gov (United States)

Moceikis, R.; Kičaitė, A.; Keturakis, E.

2017-10-01

Glass fiber reinforced concrete (GRC) opens the door for lightweight and complex shaped innovative construction, adding architectural value to buildings. With panel thickness down to 15 mm, considerable amount of total loads and materials per square meter of facade can be saved, if compared to conventionally used 80 mm thickness outer layer in insulated precast concrete wall elements. Even though GRC is used for over 50 years in such countries as Great Britain, USA and Japan, there are very few examples and little research done in Eastern Europe with this building material. European Commission propagates sustainable design as commitment to energy efficiency, environmental stewardship and conservation. For this reason, GRC plays important role in mowing toward these goals. In this paper, GRC premix recipes including fine granite and silica sands, reinforced with 13mm length alkali resistant glass fibers are investigated. Two CEM I 52,5R cements with different particle sizes were used and severe water dissociation noticed in one of concrete mixes. Cement particle size distribution determined with laser diffraction particle analyser Cilas 1090LD. To determine modulus of rupture (M.O.R.) and limit of proportionality (L.O.P), plates thickness 15 and 20 mm were produced and tested for flexural resistance according to 4-point bending scheme. Concrete workability tests were made according EN 1170-1.

Application of Chemistry in Materials Research at NASA GRC

Science.gov (United States)

Kavandi, Janet L.

2016-01-01

Overview of NASA GRC Materials Development. New materials enabled by new chemistries offering unique properties and chemical processing techniques. Durability of materials in harsh environments requires understanding and modeling of chemical interaction of materials with the environment.

Engineering Evaluation/Cost Analysis for Power Burst Facility (PER-620) Final End State and PBF Vessel Disposal

Energy Technology Data Exchange (ETDEWEB)

B. C. Culp

2007-05-01

Preparation of this engineering evaluation/cost analysis is consistent with the joint U.S. Department of Energy and U.S. Environmental Protection Agency Policy on Decommissioning of Department of Energy Facilities Under the Comprehensive Environmental Response, Compensation, and Liability Act, (DOE and EPA 1995) which establishes the Comprehensive Environmental, Response, Compensation, and Liability Act non-time critical removal action process as an approach for decommissioning. The scope of this engineering evaluation/cost analysis is to evaluate alternatives and recommend a preferred alternative for the final end state of the PBF and the final disposal location for the PBF vessel.

Turbine Seal Research at NASA GRC

Science.gov (United States)

Proctor, Margaret P.; Steinetz, Bruce M.; Delgado, Irebert R.; Hendricks, Robert C.

2011-01-01

Low-leakage, long-life turbomachinery seals are important to both Space and Aeronautics Missions. (1) Increased payload capability (2) Decreased specific fuel consumption and emissions (3) Decreased direct operating costs. NASA GRC has a history of significant accomplishments and collaboration with industry and academia in seals research. NASA's unique, state-of-the-art High Temperature, High Speed Turbine Seal Test Facility is an asset to the U.S. Engine / Seal Community. Current focus is on developing experimentally validated compliant, non-contacting, high temperature seal designs, analysis, and design methodologies to enable commercialization.

GRC: Composite material from an inorganic matrix reinforced with AR glass fibres

Directory of Open Access Journals (Sweden)

Comino Almenara, P. I.

1996-06-01

Full Text Available This article describes the historical background of Cem-FIL. Alkali Resistant Glass Fibre, as well as the composite characteristics of the element they generate: GRC. The most important advantages and properties of this type of Composite Material are also detailed.

En este artículo se detallan cuáles son las bases históricas de las Fibras de Vidrio Álcali-Resistentes Cem-FIL así como las características del elemento compuesto que ellas generan: GRC. En este documento también se pueden encontrar indicaciones sobre las principales ventajas y propiedades de este tipo de Material Compuesto.

PBF/BNCT [power burst facility/boron neutron capture therapy] program for cancer treatment

International Nuclear Information System (INIS)

Dorn, R.V. III.

1989-06-01

Highlights of the PBF/BNCT Program during June include progress within the areas of gross boron analysis in tissue, blood, and urine; analytical methodologies development for BSH (sodium borocaptate) purity determination; boron microscopic (subcellular) analytical development; noninvasive boron quantification determination; dosimetry; and analytical radiation transport and interaction modeling for BNCT

Ultrasonic characterization of GRC with high percentage of fly ash substitution.

Science.gov (United States)

Genovés, V; Gosálbez, J; Miralles, R; Bonilla, M; Payá, J

2015-07-01

New applications of non-destructive techniques (NDT) with ultrasonic tests (attenuation and velocity by means of ultrasonic frequency sweeps) have been developed for the characterization of fibre-reinforced cementitious composites. According to new lines of research on glass-fibre reinforced cement (GRC) matrix modification, two similar GRC composites with high percentages of fly ash and different water/binder ratios will be studied. Conventional techniques have been used to confirm their low Ca(OH)(2) content (thermogravimetry), fibre integrity (Scanning Electron Microscopy), low porosity (Mercury Intrusion Porosimetry) and good mechanical properties (compression and four points bending test). Ultrasound frequency sweeps allowed the estimation of the attenuation and pulse velocity as functions of frequency. This ultrasonic characterization was correlated successfully with conventional techniques. Copyright © 2015 Elsevier B.V. All rights reserved.

MAVEN Information Security Governance, Risk Management, and Compliance (GRC): Lessons Learned

Science.gov (United States)

Takamura, Eduardo; Gomez-Rosa, Carlos A.; Mangum, Kevin; Wasiak, Fran

2014-01-01

As the first interplanetary mission managed by the NASA Goddard Space Flight Center, the Mars Atmosphere and Volatile EvolutioN (MAVEN) had three IT security goals for its ground system: COMPLIANCE, (IT) RISK REDUCTION, and COST REDUCTION. In a multiorganizational environment in which government, industry and academia work together in support of the ground system and mission operations, information security governance, risk management, and compliance (GRC) becomes a challenge as each component of the ground system has and follows its own set of IT security requirements. These requirements are not necessarily the same or even similar to each other's, making the auditing of the ground system security a challenging feat. A combination of standards-based information security management based on the National Institute of Standards and Technology (NIST) Risk Management Framework (RMF), due diligence by the Mission's leadership, and effective collaboration among all elements of the ground system enabled MAVEN to successfully meet NASA's requirements for IT security, and therefore meet Federal Information Security Management Act (FISMA) mandate on the Agency. Throughout the implementation of GRC on MAVEN during the early stages of the mission development, the Project faced many challenges some of which have been identified in this paper. The purpose of this paper is to document these challenges, and provide a brief analysis of the lessons MAVEN learned. The historical information documented herein, derived from an internal pre-launch lessons learned analysis, can be used by current and future missions and organizations implementing and auditing GRC.

'GRC1.5': Uptower Gearbox Testing to Investigate Bearing Axial Cracking

Energy Technology Data Exchange (ETDEWEB)

Keller, Jonathan; Vaes, David; McNiff, Brian

2016-02-16

This presentation focuses on the investigation of bearing axial cracking using the GRC1.5 uptower gearbox. Topics covered include the testing options considered, the project goal, and current and near-term activities.

75 FR 24941 - PBF Power Marketing LLC; Supplemental Notice That Initial Market-Based Rate Filing Includes...

Science.gov (United States)

2010-05-06

... Marketing LLC; Supplemental Notice That Initial Market- Based Rate Filing Includes Request for Blanket... of PBF Power Marketing LLC's application for market-based rate authority, with an accompanying rate... protests and interventions in lieu of paper, using the FERC Online links at http://www.ferc.gov . To...

Slow neutron total cross-section, transmission and reflection calculation for poly- and mono-NaCl and PbF2 crystals

Science.gov (United States)

Mansy, Muhammad S.; Adib, M.; Habib, N.; Bashter, I. I.; Morcos, H. N.; El-Mesiry, M. S.

2016-10-01

A detailed study about the calculation of total neutron cross-section, transmission and reflection from crystalline materials was performed. The developed computer code is approved to be sufficient for the required calculations, also an excellent agreement has been shown when comparing the code results with the other calculated and measured values. The optimal monochromator and filter parameters were discussed in terms of crystal orientation, mosaic spread, and thickness. Calculations show that 30 cm thick of PbF2 poly-crystal is an excellent cold neutron filter producing neutron wavelengths longer than 0.66 nm needed for the investigation of magnetic structure experiments. While mono-crystal filter PbF2 cut along its (1 1 1), having mosaic spread (η = 0.5°) and thickness 10 cm can only transmit thermal neutrons of the desired wavelengths and suppress epithermal and γ-rays forming unwanted background, when it is cooled to liquid nitrogen temperature. NaCl (2 0 0) and PbF2 (1 1 1) monochromator crystals having mosaic spread (η = 0.5°) and thickness 10 mm shows high neutron reflectivity for neutron wavelengths (λ = 0.114 nm and λ = 0.43 nm) when they used as a thermal and cold neutron monochromators respectively with very low contamination from higher order reflections.

Advanced Manufacturing Technologies (AMT): Additive Manufactured Hot Fire Planning and Testing in GRC Cell 32

Data.gov (United States)

National Aeronautics and Space Administration — The objective of this project is to hot fire test an additively manufactured thrust chamber assembly TCA (injector and thrust chamber). GRC will install the...

2014 Overview of NASA GRC Electrochemical Power and Energy Storage Technology

Science.gov (United States)

Reid, Concha M.

2014-01-01

Overview presentation to the IAPG Chemical Working Group meeting, discussing current electrochemical power and energy storage R and D at NASA GRC including missions, demonstrations, and reserch projects. Activities such as ISS Lithium-Ion Battery Replacements, the Advanced Exploration Systems Modular Power Systems project, Enabling Electric Aviation with Ultra-High Energy Litium Metal Batteries, Advanced Space Power Systems project, and SBIR STTR work, will be discussed.

Overview of Multi-Kilowatt Free-Piston Stirling Power Conversion Research at GRC

Science.gov (United States)

Geng, Steven M.; Mason, Lee S.; Dyson, Rodger W.; Penswick, L. Barry

2008-01-01

As a step towards development of Stirling power conversion for potential use in Fission Surface Power (FSP) systems, a pair of commercially available 1 kW class free-piston Stirling convertors and a pair of commercially available pressure wave generators (which will be plumbed together to create a high power Stirling linear alternator test rig) have been procured for in-house testing at Glenn Research Center. Delivery of both the Stirling convertors and the linear alternator test rig is expected by October, 2007. The 1 kW class free-piston Stirling convertors will be tested at GRC to map and verify performance. The convertors will later be modified to operate with a NaK liquid metal pumped loop for thermal energy input. The high power linear alternator test rig will be used to map and verify high power Stirling linear alternator performance and to develop power management and distribution (PMAD) methods and techniques. This paper provides an overview of the multi-kilowatt free-piston Stirling power conversion work being performed at GRC.

Overview of Multi-kilowatt Free-Piston Stirling Power Conversion Research at GRC

Science.gov (United States)

Geng, Steven M.; Mason, Lee S.; Dyson, Rodger W.; Penswick, L. Barry

2008-01-01

As a step towards development of Stirling power conversion for potential use in Fission Surface Power (FSP) systems, a pair of commercially available 1 kW class free-piston Stirling convertors and a pair of commercially available pressure wave generators (which will be plumbed together to create a high power Stirling linear alternator test rig) have been procured for in-house testing at Glenn Research Center. Delivery of both the Stirling convertors and the linear alternator test rig is expected by October, 2007. The 1 kW class free-piston Stirling convertors will be tested at GRC to map and verify performance. The convertors will later be modified to operate with a NaK liquid metal pumped loop for thermal energy input. The high power linear alternator test rig will be used to map and verify high power Stirling linear alternator performance and to develop power management and distribution (PMAD) methods and techniques. This paper provides an overview of the multi-kilowatt free-piston Stirling power conversion work being performed at GRC.

2009 Archaea: Ecology, Metabolism & Molecular Biology GRC

Energy Technology Data Exchange (ETDEWEB)

Furlow, Julie Maupin- [Univ. of Florida, Gainesville, FL (United States)

2009-07-26

Archaea, one of three major evolutionary lineages of life, are a fascinating and diverse group of microbes with deep roots overlapping those of eukaryotes. The focus of the 'Archaea: Ecology Metabolism & Molecular Biology' GRC conference expands on a number of emerging topics highlighting new paradigms in archaeal metabolism, genome function and systems biology; information processing; evolution and the tree of life; the ecology and diversity of archaea and their viruses; and industrial applications. The strength of this conference lies in its ability to couple a field with a rich history in high quality research with new scientific findings in an atmosphere of stimulating exchange. This conference remains an excellent opportunity for younger scientists to interact with world experts in this field.

78 FR 62614 - Guttman Energy, Inc., PBF Holding Company LLC v. Buckeye Pipe Line Company, L.P., Laurel Pipe...

Science.gov (United States)

2013-10-22

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket No. OR14-4-000] Guttman Energy, Inc., PBF Holding Company LLC v. Buckeye Pipe Line Company, L.P., Laurel Pipe Line Company, L.P... complaint against Buckeye Pipe Line Company L.P. and Laurel Pipe Line Company L.P. (Respondents) challenging...

Wind Turbine Drivetrain Condition Monitoring During GRC Phase 1 and Phase 2 Testing

Energy Technology Data Exchange (ETDEWEB)

Sheng, S.; Link, H.; LaCava, W.; van Dam, J.; McNiff, B.; Veers, P.; Keller, J.; Butterfield, S.; Oyague, F.

2011-10-01

This report will present the wind turbine drivetrain condition monitoring (CM) research conducted under the phase 1 and phase 2 Gearbox Reliability Collaborative (GRC) tests. The rationale and approach for this drivetrain CM research, investigated CM systems, test configuration and results, and a discussion on challenges in wind turbine drivetrain CM and future research and development areas, will be presented.

MELCOR modeling of the PBF [Power Burst Facility] Severe Fuel Damage Test 1-4

International Nuclear Information System (INIS)

Madni, I.K.

1990-01-01

This paper describes a MELCOR Version 1.8 simulation of the Power Burst Facility (PBF) Severe Fuel Damage (SFD) Test 1--4. The input data for the analysis were obtained from the Test Results Report and from SCDAP/RELAP5 input. Results are presented for the transient liquid level in the test bundle, clad temperatures, shroud temperatures, clad oxidation and hydrogen generation, bundle geometry changes, fission product release, and heat transfer to the bypass flow. Comparisons are made with experimental data and with SCDAP/RELAP5 calculations. 10 refs., 7 figs

High temporal versus high spatial resolution in MR quantitative pulmonary perfusion imaging of two-year old children after congenital diaphragmatic hernia repair

Energy Technology Data Exchange (ETDEWEB)

Weidner, M.; Hagelstein, C.; Schoenberg, S.O.; Neff, K.W. [University Medical Center Mannheim, Medical Faculty Mannheim, Heidelberg University, Institute of Clinical Radiology and Nuclear Medicine, Mannheim (Germany); Zoellner, F.G.; Schad, L.R. [Heidelberg University, Computer Assisted Clinical Medicine, Medical Faculty Mannheim, Mannheim (Germany); Zahn, K. [University Medical Center Mannheim, Medical Faculty Mannheim, University of Heidelberg, Department of Pediatric Surgery, Mannheim (Germany); Schaible, T. [University Medical Center Mannheim, Medical Faculty Mannheim, Heidelberg University, Department of Pediatrics, Mannheim (Germany)

2014-10-15

Congenital diaphragmatic hernia (CDH) leads to lung hypoplasia. Using dynamic contrast-enhanced (DCE) MR imaging, lung perfusion can be quantified. As MR perfusion values depend on temporal resolution, we compared two protocols to investigate whether ipsilateral lung perfusion is impaired after CDH, whether there are protocol-dependent differences, and which protocol is preferred. DCE-MRI was performed in 36 2-year old children after CDH on a 3 T MRI system; protocol A (n = 18) based on a high spatial (3.0 s; voxel: 1.25 mm{sup 3}) and protocol B (n = 18) on a high temporal resolution (1.5 s; voxel: 2 mm{sup 3}). Pulmonary blood flow (PBF), pulmonary blood volume (PBV), mean transit time (MTT), and peak-contrast-to-noise-ratio (PCNR) were quantified. PBF was reduced ipsilaterally, with ipsilateral PBF of 45 ± 26 ml/100 ml/min to contralateral PBF of 63 ± 28 ml/100 ml/min (p = 0.0016) for protocol A; and for protocol B, side differences were equivalent (ipsilateral PBF = 62 ± 24 vs. contralateral PBF = 85 ± 30 ml/100 ml/min; p = 0.0034). PCNR was higher for protocol B (30 ± 18 vs. 20 ± 9; p = 0.0294). Protocol B showed higher values of PBF in comparison to protocol A (p always <0.05). Ipsilateral lung perfusion is reduced in 2-year old children following CDH repair. Higher temporal resolution and increased voxel size show a gain in PCNR and lead to higher perfusion values. Protocol B is therefore preferred. (orig.)

Aplicaciones del cemento reforzado con fibra de vidrio (GRC

Directory of Open Access Journals (Sweden)

Barros Llerena, Ángel

1981-12-01

Full Text Available Not available.

El presente artículo tiene como objeto dar a conocer la utilización de fibras de vidrio como refuerzo de los cementos. Se da una breve reseña histórica, se mencionan sus características y comportamiento. Además se presenta un caso práctico y reciente de utilización en la fabricación de elementos de fachada del Estadio «Santiago Bernabéu» del Real Madrid C. de F., y se completa con una relación de los actuales y futuros usos del G.R.C. (glass reinforced cement, denominación inglesa del material más comúnmente utilizado.

Reconfiguration of NASA GRC's Vacuum Facility 6 for Testing of Advanced Electric Propulsion System (AEPS) Hardware

Science.gov (United States)

Peterson, Peter Y.; Kamhawi, Hani; Huang, Wensheng; Yim, John T.; Haag, Thomas W.; Mackey, Jonathan A.; McVetta, Michael S.; Sorrelle, Luke T.; Tomsik, Thomas M.; Gilligan, Ryan P.;

'The money can be a motivator, to me a little, but mostly PBF just helps me to do better in my job.' An exploration of the motivational mechanisms of performance-based financing for health workers in Malawi.

Science.gov (United States)

Lohmann, Julia; Wilhelm, Danielle; Kambala, Christabel; Brenner, Stephan; Muula, Adamson S; De Allegri, Manuela

2018-03-01

Performance-based financing (PBF) is assumed to improve health care delivery by motivating health workers to enhance their work performance. However, the exact motivational mechanisms through which PBF is assumed to produce such changes are poorly understood to date. Although PBF is increasingly recognized as a complex health systems intervention, its motivational effect for individual health workers is still often reduced to financial 'carrots and sticks' in the literature and discourse. Aiming to contribute to the development of a more comprehensive understanding of the motivational mechanisms, we explored how PBF impacted health worker motivation in the context of the Malawian Results-based Financing for Maternal and Newborn Health (RBF4MNH) Initiative. We conducted in-depth interviews with 41 nurses, medical assistants and clinical officers from primary- and secondary-level health facilities 1 and 2 years after the introduction of RBF4MNH in 2013. Six categories of motivational mechanisms emerged: RBF4MNH motivated health workers to improve their performance (1) by acting as a periodic wake-up call to deficiencies in their day-to-day practice; (2) by providing direction and goals to work towards; (3) by strengthening perceived ability to perform successfully at work and triggering a sense of accomplishment; (4) by instilling feelings of recognition; (5) by altering social dynamics, improving team work towards a common goal, but also introducing social pressure; and (6) by offering a 'nice to have' opportunity to earn extra income. However, respondents also perceived weaknesses of the intervention design, implementation-related challenges and contextual constraints that kept RBF4MNH from developing its full motivating potential. Our results underline PBF's potential to affect health workers' motivation in ways which go far beyond the direct effects of financial rewards to individuals. We strongly recommend considering all motivational mechanisms more explicitly

Práticas discursivas e modos de subjetivação de mulheres beneficiárias do Programa Bolsa Família (PBF) em contextos rurais. O caso da Zona da Mata Pernambucana

OpenAIRE

MUNOZ, Claudio Baradit

2016-01-01

O presente estudo tem por objetivo analisar as práticas discursivas que constituem os modos de subjetivação de mulheres beneficiárias do Programa Bolsa Família (PBF) em contexto rural. Para isto será estudado o caso da Zona da Mata de Pernambuco. A metodologia qualitativa consiste na análise crítica do discurso. Os dados foram obtidos através de entrevistas semiestruturadas de seis mulheres. A fundamentação teórica é baseada no enfoque da governamentalidade, nas críticas feministas ao PBF e n...

PBF/LOFT Lead Rod Test Program experiment operating specification

International Nuclear Information System (INIS)

Varacalle, D.J. Jr.

1978-11-01

The PBF/LOFT Lead Rod (LLR) Test Program is being conducted to provide experimental information on the behavior of nuclear fuel under normal and accident conditions in the Power Burst Facility at the Idaho National Engineering Laboratory. Understanding the behavior of light-water reactors (LWR) under loss-of-coolant conditions is a major objective of the NRC Reactor Safety Research Program. The Loss of Fluid Test (LOFT) facility is the major testing facility to evaluate the systems response of an LWR over a wide range of Loss of Coolant Experment (LOCE) conditions. As such, the LOFT core is intended to be used for sequential LOCE tests provided no significant fuel rod failures occur. The PFB/LLR tests are designed to simulate the test conditions for the LOFT Power Ascension Tests L2-2 through L2-5. The test program has been designed to provide a parametric evaluation of the LOFT fuel over a wide range of power. Thus, a relatively accurate assessment of the state of the LOFT core after the completion of each subtest and the anticipated effect of the next test can be obtained by utilizing a combination of LLR test data and analytical predictions. Specifications for the test program are presented

Advanced Manufacturing Technologies (AMT): Additive Manufactured Hot Fire Planning and Testing in GRC Cell 32 Project

Science.gov (United States)

Fikes, John C.

2014-01-01

The objective of this project is to hot fire test an additively manufactured thrust chamber assembly TCA (injector and thrust chamber). GRC will install the additively manufactured Inconel 625 injector, two additively manufactured (SLM) water cooled Cu-Cr thrust chamber barrels and one additively manufactured (SLM) water cooled Cu-Cr thrust chamber nozzle on the test stand in Cell 32 and perform hot fire testing of the integrated TCA.

Results of the first nuclear blowdown test on single fuel rods (LOC-11 Series in PBF)

International Nuclear Information System (INIS)

Larson, J.R.; Evans, D.R.; McCardell, R.K.

1978-01-01

This paper presents results of the first nuclear blowdown tests (LOC-11A, LOC-11B, LOC-11C) ever conducted. The Loss-of-Coolant Accident (LOCA) Test Series is being conducted in the Power Burst Facility (PBF) reactor at the Idaho National Engineering Laboratory, near Idaho Falls, Idaho, for the Nuclear Regulatory Commission. The objective of the LOC-11 tests was to obtain data on the behavior of pressurized and unpressurized rods when exposed to a blowdown similar to that expected in a pressurized water reactor (PWR) during a hypothesized double-ended cold-leg break. The data are being used for the development and verification of analytical models that are used to predict coolant and fuel rod pressure during a LOCA in a PWR

Effects of Powder Attributes and Laser Powder Bed Fusion (L-PBF) Process Conditions on the Densification and Mechanical Properties of 17-4 PH Stainless Steel

Science.gov (United States)

Irrinki, Harish; Dexter, Michael; Barmore, Brenton; Enneti, Ravi; Pasebani, Somayeh; Badwe, Sunil; Stitzel, Jason; Malhotra, Rajiv; Atre, Sundar V.

2016-03-01

The effects of powders attributes (shape and size distribution) and critical processing conditions (energy density) on the densification and mechanical properties of laser powder bed fusion (L-PBF) 17-4 PH stainless steel were studied using four types of powders. The % theoretical density, ultimate tensile strength and hardness of both water- and gas-atomized powders increased with increased energy density. Gas-atomized powders showed superior densification and mechanical properties when processed at low energy densities. However, the % theoretical density and mechanical properties of water-atomized powders were comparable to gas-atomized powders when sintered at a high energy density of 104 J/mm3. An important result of this study was that, even at high % theoretical density (97% ± 1%), the properties of as-printed parts could vary over a relatively large range (UTS: 500-1100 MPa; hardness: 25-39 HRC; elongation: 10-25%) depending on powder characteristics and process conditions. The results also demonstrate the feasibility of using relatively inexpensive water-atomized powders as starting raw material instead of the typically used gas-atomized powders to fabricate parts using L-PBF techniques by sintering at high energy densities.

Characteristics of severely damaged fuel from PBF tests and the TMI-2 accident

International Nuclear Information System (INIS)

Osetek, D.J.; Cook, B.A.; Dallman, R.J.; Broughton, J.M.

1986-01-01

As a result of the TMI-2 reactor accident, the US Nuclear Regulatory Commission initiated a research program to investigate phenomena associated with severe fuel damage accidents. This program is sponsored by several countries and includes in-pile and out-of-pile experiments, separate effects studies, and computer code development. The principal in-pile testing portion of the program includes four integral severe fuel damage (SFD) tests in the Power Burst Facility (PBF) at the Idaho National Engineering Laboratory (INEL). The INEL is also responsible for examining the damaged core in the Three Mile Island-Unit 2 (TMI-2) reactor, which offers the unique opportunity to directly compare the findings of an experimental program to those of an actual reactor accident. The principal core damage phenomena which can occur during a severe accident are discussed, and examples from the INEL research programs are used to illustrate the characteristics of these phenomena. The preliminary results of the programs are presented, and their impact on plant operability during severe accidents is discussed

Verification of computer code FPRETAIN with respect to RIA data from SPERT and PBF experiments

International Nuclear Information System (INIS)

Heo, Young-Ho; Yanagisawa, Kazuaki.

1992-12-01

This report presents the comparisons between calculated and measured fuel rod behavior and the analysis of stress for preirradiated LWR type fuel rods during reactivity initiated accident (RIA) conditions. For the calculations, FPRETAIN computer code which can simulate the fuel behavior under RIA conditions at extended burnup stage was used. For the experimental, data obtained from the Special Power Excursion Reactor Test (SPERT) and the Power Burst Facility (PBF) tests were used. The results of the comparisons showed that the FPRETAIN code predicted well the tendency of the fuel rod behavior during RIA. From the results of the stress analysis, it was found that the maximum hoop stress of cladding was not proportional to the energy deposition of fuel rod. Calculated cladding maximum hoop stress of failed fuel at high burnup was not lower than that of intact fresh or low burnup fuel. (author)

Quantitative pulmonary perfusion imaging with 3-dimensional, contrast-enhanced MR: regional difference in the perfusion parameters of healthy volunteers

International Nuclear Information System (INIS)

Kim, Song Soo; Seo, Joon Beom; Kim, Nam Kuk; Do, Kyung Hyun; Lee, Young Kyung; Song, Jae Woo; Lee, Jin Seong; Kim, Jin Hwan

2007-01-01

We wanted to evaluate the regional differences in such perfusion parameters as pulmonary blood flow (PBF), mean transit time (MTT) and pulmonary blood volume (PBV) in the entire lung of healthy volunteers with using three-dimensional, contrast-enhanced MR imaging (3D CEMRI). Six healthy volunteers underwent dynamic 3D CEMRI (TR/TE 2.7/0.6 msec; flip angle 40 .deg. ; matrix 128 x 96; reconstructed matrix 256 x 192; rectangular field of view 450 x 315 mm; coronal 100-150mm-thick x 10 slabs; temporal resolution 1.0 sec; 35 dynamic phases) For all subjects, 2 mL of Gd-DTPA mixed with 3 ml of physiologic saline was administered as a bolus at a rate of 5 mL/sec, and this was followed by 20 mL of physiologic saline flush. From the signal intensity-time curves, the PBF, MTT and PBV maps were generated using indicator dilution theories and the central volume principle on a pixel-by-pixel basis. A total of 54 round, 1-cm sized ROIs were placed in the lung in each subject (6 ROIs per slab x 9 slices except for the most posterior slab). The regional differences of the measured parameters were statistically evaluated in the gravitational direction and in the upper-mid-lower direction by one-way ANOVA tests. The calculated PBF, MTT and PBV in the entire lung were 141.8 ± 53.4 mL/100 mL/min (mean ± SD), 5.35 ± 1.38 sec, and 13.4 ± 6.48 mL/100mL, respectively. In the gravitational direction, there was a significant increase in the PBF and PBV as it goes to the posterior direction (ρ < 0.05). No statistical difference was found in PBF or PBV between the upper, mid and lower lung zone areas. Regional difference in the various perfusion parameters of the lung in healthy volunteers can be quantitatively assessed with performing 3D CEMRI

An electrochemical study of the flow rate effect on the oxide film of SA106 Gr.C piping

International Nuclear Information System (INIS)

Hong, S. M.; Kim, J. H.; Kim, I. S.

2002-01-01

Effect of water flow rate on the oxide film of SA106 Gr.C piping was evaluated quantitatively through electrochemical method. It was carried out with weight change experiments, polarization tests, and EIS tests with rig that simulates water flow. Without water flow, the oxide film is so stable that it effectively blocks current exchange. With water flow, the oxide film was damaged and electrochemical current density and oxide film properties, C dl and R p were significantly changed

Heat treatment versus properties studies associated with the Inconel 718 PBF acoustic filters

International Nuclear Information System (INIS)

Smolik, G.R.; Reuter, W.G.

1975-01-01

PBF acoustic filter Unit No. 1 cracked when heat treatment was attempted. The effects of prior thermal cycling, solution anneal temperature, and cooling rate from solution anneals were investigated. The investigations concerned influences of the above variables upon both 1400 0 F stress rupture solution-annealed properties and room temperature age-hardened properties. 1400 0 F stress rupture properties were of interest to assist the prevention of cracking during heat treatments. Room temperature age-hardened properties were needed to ensure that design requirement would be provided. Prior thermal cycling was investigated to determine if extra thermal cycles would be detrimental to the repaired filter. Slow furnace cools were considered as a means of reducing thermal stresses. Effects of solution annealing at 2000 and 1900 0 F were also determined. Test results showed that slow cooling rates would not only reduce thermal stresses but also improve 1400 0 F ductility. A modified aging treatment was established which provided the required 145 ksi room temperature yield strength for the slowly cooled material. Prior cooling did not degrade final age-hardened room temperature tensile or impact properties

Heterogeneity of pulmonary perfusion as a mechanistic image-based phenotype in emphysema susceptible smokers.

Science.gov (United States)

Alford, Sara K; van Beek, Edwin J R; McLennan, Geoffrey; Hoffman, Eric A

2010-04-20

Recent evidence suggests that endothelial dysfunction and pathology of pulmonary vascular responses may serve as a precursor to smoking-associated emphysema. Although it is known that emphysematous destruction leads to vasculature changes, less is known about early regional vascular dysfunction which may contribute to and precede emphysematous changes. We sought to test the hypothesis, via multidetector row CT (MDCT) perfusion imaging, that smokers showing early signs of emphysema susceptibility have a greater heterogeneity in regional perfusion parameters than emphysema-free smokers and persons who had never smoked (NS). Assuming that all smokers have a consistent inflammatory response, increased perfusion heterogeneity in emphysema-susceptible smokers would be consistent with the notion that these subjects may have the inability to block hypoxic vasoconstriction in patchy, small regions of inflammation. Dynamic ECG-gated MDCT perfusion scans with a central bolus injection of contrast were acquired in 17 NS, 12 smokers with normal CT imaging studies (SNI), and 12 smokers with subtle CT findings of centrilobular emphysema (SCE). All subjects had normal spirometry. Quantitative image analysis determined regional perfusion parameters, pulmonary blood flow (PBF), and mean transit time (MTT). Mean and coefficient of variation were calculated, and statistical differences were assessed with one-way ANOVA. MDCT-based MTT and PBF measurements demonstrate globally increased heterogeneity in SCE subjects compared with NS and SNI subjects but demonstrate similarity between NS and SNI subjects. These findings demonstrate a functional lung-imaging measure that provides a more mechanistically oriented phenotype that differentiates smokers with and without evidence of emphysema susceptibility.

Quantitative pulmonary perfusion imaging at 3.0 T of 2-year-old children after congenital diaphragmatic hernia repair: initial results

International Nuclear Information System (INIS)

Zoellner, F.G.; Schad, L.R.; Zahn, K.; Schaible, T.; Schoenberg, S.O.; Neff, K.W.

2012-01-01

To investigate whether dynamic contrast-enhanced MR imaging of the lung following congenital diaphragmatic hernia repair is feasible at 3.0 T in 2-year-old children and whether associated lung hypoplasia (reflected in reduced pulmonary microcirculation) can be demonstrated in MRI. Twelve children with a mean age 2.0 ± 0.2 years after hernia repair underwent DCE-MRI at 3.0 T using a time-resolved angiography with stochastic trajectories sequence. Quantification of lung perfusion was performed using a pixel-by-pixel deconvolution approach. Six regions of interest were placed (upper, middle and lower parts of right and left lung) to assess differences in pulmonary blood flow (PBF), pulmonary blood volume (PBV) and mean transit time (MTT) while avoiding the inclusion of larger pulmonary arteries and veins. The difference in PBF and PBV between ipsilateral and contralateral lung was significant (P < 0.5). No significant differences could be detected for the MTT (P = 0.5). DCE-MRI in 2-year-old patients is feasible at 3.0 T. Reduced perfusion in the ipsilateral lung is reflected by significantly lower PBF values compared with the contralateral lung. DCE-MRI of the lung in congenital diaphragmatic hernia can help to characterise lung hypoplasia initially and in the long-term follow-up of children after diaphragmatic repair. (orig.)

Reduced thermal sensitivity of hybrid air-core photonic band-gap fiber ring resonator

Science.gov (United States)

Feng, Li-shuang; Wang, Kai; Jiao, Hong-chen; Wang, Jun-jie; Liu, Dan-ni; Yang, Zhao-hua

2018-01-01

A novel hybrid air-core photonic band-gap fiber (PBF) ring resonator with twin 90° polarization-axis rotated splices is proposed and demonstrated. Frist, we measure the temperature dependent birefringence coefficient of air-core PBF and Panda fiber. Experimental results show that the relative temperature dependent birefringence coefficient of air-core PBF is 1.42×10-8/°C, which is typically 16 times less than that of Panda fiber. Then, we extract the geometry profile of air-core PBF from scanning electron microscope (SEM) images. Numerical modal is built to distinguish the fast axis and slow axis in the fiber. By precisely setting the length difference in air-core PBF and Panda fiber between two 90° polarization-axis rotated splicing points, the hybrid air-core PBF ring resonator is constructed, and the finesse of the resonator is 8.4. Environmental birefringence variation induced by temperature change can be well compensated, and experimental results show an 18-fold reduction in thermal sensitivity, compared with resonator with twin 0° polarization-axis rotated splices.

Fraud in Rights and Contracts: A Review of Bankruptcy Case of Livent Inc. Based on Governance, Risk, and Compliance (GRC Framework

Directory of Open Access Journals (Sweden)

Samuel Anindyo Widhoyoko

2017-05-01

Full Text Available This research discussed the accounting scandal in the perspective of governance, risk, and compliance using Governance, Risk, and Compliance (GRC framework. Unlike other fraud’s framework, GRC framework combinedthree different aspects of business sustainability of reporting. The purpose of the research was to highlight early business fraud that usually initiated by the company in boosting up the revenue during the Initial public offering(IPO processes. When other research discussed the business’ fraud schemes through the document alteration, this research focused on a case showing how a business could make the wrong statement to the investors through real and lawful future contracts with unqualified audit opinion. Structurally, this research was done through the action research method in pointing out all the directors’ failures in their function to hold the fiduciary duty to exercise their responsibility. Based on the analysis with the accordance with the framework used, it is highlighted that directors in the aspect of (1 governance decisive, they fail to set proportional target, provide ethical value, and react positively to maintain the company sustainability; (2 compliance submissive, they do not submit the accounting standards through undisclosed third-party agreement, misrepresentation of revenue recognition, and mistreatment of expense omission; (3 risk preventive, they fail to assess the risk occurs from legal aspect of conflict of interest, long-term contractual and engagement risks, and insufficient future cash flow.

2009 Cellulosomes, Cellulases & Other Carbohydrate Modifying Enzymes GRC

Energy Technology Data Exchange (ETDEWEB)

Gilbert, Harry [Univ. of Newcastle, Callaghan, NSW (Australia)

2009-07-26

your application/abstract to the GRC web site as soon as possible.

The influence of image reconstruction algorithms on linear thorax EIT image analysis of ventilation.

Science.gov (United States)

Zhao, Zhanqi; Frerichs, Inéz; Pulletz, Sven; Müller-Lisse, Ullrich; Möller, Knut

2014-06-01

Analysis methods of electrical impedance tomography (EIT) images based on different reconstruction algorithms were examined. EIT measurements were performed on eight mechanically ventilated patients with acute respiratory distress syndrome. A maneuver with step increase of airway pressure was performed. EIT raw data were reconstructed offline with (1) filtered back-projection (BP); (2) the Dräger algorithm based on linearized Newton-Raphson (DR); (3) the GREIT (Graz consensus reconstruction algorithm for EIT) reconstruction algorithm with a circular forward model (GR(C)) and (4) GREIT with individual thorax geometry (GR(T)). Individual thorax contours were automatically determined from the routine computed tomography images. Five indices were calculated on the resulting EIT images respectively: (a) the ratio between tidal and deep inflation impedance changes; (b) tidal impedance changes in the right and left lungs; (c) center of gravity; (d) the global inhomogeneity index and (e) ventilation delay at mid-dorsal regions. No significant differences were found in all examined indices among the four reconstruction algorithms (p > 0.2, Kruskal-Wallis test). The examined algorithms used for EIT image reconstruction do not influence the selected indices derived from the EIT image analysis. Indices that validated for images with one reconstruction algorithm are also valid for other reconstruction algorithms.

Studies of an array of PbF2 Cherenkov crystals with large-area SiPM readout

Energy Technology Data Exchange (ETDEWEB)

Fienberg, A. T.; Alonzi, L. P.; Anastasi, A.; Bjorkquist, R.; Cauz, D.; Fatemi, R.; Ferrari, C.; Fioretti, A.; Frankenthal, A.; Gabbanini, C.; Gibbons, L. K.; Giovanetti, K.; Goadhouse, S. D.; Gohn, W. P.; Gorringe, T. P.; Hertzog, D. W.; Iacovacci, M.; Kammel, P.; Kaspar, J.; Kiburg, B.; Li, L.; Mastroianni, S.; Pauletta, G.; Peterson, D. A.; Počanić, D.; Smith, M. W.; Sweigart, D. A.; Tishchenko, V.; Venanzoni, G.; Van Wechel, T. D.; Wall, K. B.; Winter, P.; Yai, K.

2015-05-01

The electromagnetic calorimeter for the new muon (g-2) experiment at Fermilab will consist of arrays of PbF2 Cherenkov crystals read out by large-area silicon photo-multiplier (SiPM) sensors. We report here on measurements and simulations using 2.0 -- 4.5 GeV electrons with a 28-element prototype array. All data were obtained using fast waveform digitizers to accurately capture signal pulse shapes versus energy, impact position, angle, and crystal wrapping. The SiPMs were gain matched using a laser-based calibration system, which also provided a stabilization procedure that allowed gain correction to a level of 1e-4 per hour. After accounting for longitudinal fluctuation losses, those crystals wrapped in a white, diffusive wrapping exhibited an energy resolution sigma/E of (3.4 +- 0.1) % per sqrt(E/GeV), while those wrapped in a black, absorptive wrapping had (4.6 +- 0.3) % per sqrt(E/GeV). The white-wrapped crystals---having nearly twice the total light collection---display a generally wider and impact-position-dependent pulse shape owing to the dynamics of the light propagation, in comparison to the black-wrapped crystals, which have a narrower pulse shape that is insensitive to impact position.

Demonstration of pulmonary perfusion heterogeneity induced by gravity and lung inflation using arterial spin labeling

Energy Technology Data Exchange (ETDEWEB)

Fan Li [Department of Radiology, ChangZheng Hospital, Second Military Medical University, Shanghai 200003 (China)], E-mail: fanli0930@163.com; Liu Shiyuan [Department of Radiology, ChangZheng Hospital, Second Military Medical University, Shanghai 200003 (China)], E-mail: fanli7938@chinaren.com; Xiao Xiangsheng [Department of Radiology, ChangZheng Hospital, Second Military Medical University, Shanghai 200003 (China)], E-mail: lizhaobin79@163.com; Sun Fei [GE Healthcare (China)], E-mail: Fei.sun@med.ge.com

2010-02-15

Objective: To evaluate the effect of gravity and lung inflation on pulmonary perfusion heterogeneity in human lung using an arterial spin labeling (ASL) sequence called flow sensitive alternating inversion recovery (FAIR). Materials and methods: Magnetic resonance imaging of lung perfusion using arterial spin labeling sequence was performed in supine position in ten healthy volunteers on a 1.5 T whole body scanner (GE Healthcare). Five coronal slices at an interval of 3 cm from dorsal to ventral (labeled as P3, P6, P9, P12, P15, sequently) were obtained when the volunteers performed breath holding on end expiration and the relative pulmonary blood flow (rPBF) was measured. Then, another coronal perfusion-weighted image of P3 slice was obtained on end inspiration. Tagging efficiency of pulmonary parenchyma with IR ({delta}SI), rPBF and area of the P3 slice were analyzed. Results: (1) Along the direction of gravity, a gradient was visually perceived as a vertical increase in rPBF. There were significant statistic differences in rPBF between any two coronal planes except that between P12 and P15. In supine position, regression coefficients of right and left lung were -4.98 and -5.16, respectively. This means that rPBF decreased 4.98 (right) and 5.16 (left) for each centimeter above the dorsal. No statistical difference was seen between ROIs placed along iso-gravitational plane. (2) For a same slice, there were significant statistic differences in {delta}SI, rPBF and area at different respiratory phases (P < 0.05). Greater {delta}SI and more perfusion were observed on end expiration than on end inspiration. The area was larger on end inspiration than on end expiration. Conclusion: Both gravity and respiratory phase are important determinants of pulmonary perfusion heterogeneity. FAIR is sensitive to demonstrate gravity- and respiratory phase-dependent differences in lung perfusion. Positioning the patient so that the area of interest is down-gravity and asking patient

Dynamic Network Communication in the Human Functional Connectome Predicts Perceptual Variability in Visual Illusion.

Science.gov (United States)

Wang, Zhiwei; Zeljic, Kristina; Jiang, Qinying; Gu, Yong; Wang, Wei; Wang, Zheng

2018-01-01

Ubiquitous variability between individuals in visual perception is difficult to standardize and has thus essentially been ignored. Here we construct a quantitative psychophysical measure of illusory rotary motion based on the Pinna-Brelstaff figure (PBF) in 73 healthy volunteers and investigate the neural circuit mechanisms underlying perceptual variation using functional magnetic resonance imaging (fMRI). We acquired fMRI data from a subset of 42 subjects during spontaneous and 3 stimulus conditions: expanding PBF, expanding modified-PBF (illusion-free) and expanding modified-PBF with physical rotation. Brain-wide graph analysis of stimulus-evoked functional connectivity patterns yielded a functionally segregated architecture containing 3 discrete hierarchical networks, commonly shared between rest and stimulation conditions. Strikingly, communication efficiency and strength between 2 networks predominantly located in visual areas robustly predicted individual perceptual differences solely in the illusory stimulus condition. These unprecedented findings demonstrate that stimulus-dependent, not spontaneous, dynamic functional integration between distributed brain networks contributes to perceptual variability in humans. © The Author 2016. Published by Oxford University Press. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

Transient receptor potential ankyrin 1 receptor activation in vitro and in vivo by pro-tussive agents: GRC 17536 as a promising anti-tussive therapeutic.

Directory of Open Access Journals (Sweden)

Indranil Mukhopadhyay

Full Text Available Cough is a protective reflex action that helps clear the respiratory tract which is continuously exposed to airborne environmental irritants. However, chronic cough presents itself as a disease in its own right and despite its global occurrence; the molecular mechanisms responsible for cough are not completely understood. Transient receptor potential ankyrin1 (TRPA1 is robustly expressed in the neuronal as well as non-neuronal cells of the respiratory tract and is a sensor of a wide range of environmental irritants. It is fast getting acceptance as a key biological sensor of a variety of pro-tussive agents often implicated in miscellaneous chronic cough conditions. In the present study, we demonstrate in vitro direct functional activation of TRPA1 receptor by citric acid which is routinely used to evoke cough in preclinical and clinical studies. We also show for the first time that a potent and selective TRPA1 antagonist GRC 17536 inhibits citric acid induced cellular Ca(+2 influx in TRPA1 expressing cells and the citric acid induced cough response in guinea pigs. Hence our data provides a mechanistic link between TRPA1 receptor activation in vitro and cough response induced in vivo by citric acid. Furthermore, we also show evidence for TRPA1 activation in vitro by the TLR4, TLR7 and TLR8 ligands which are implicated in bacterial/respiratory virus pathogenesis often resulting in chronic cough. In conclusion, this study highlights the potential utility of TRPA1 antagonist such as GRC 17536 in the treatment of miscellaneous chronic cough conditions arising due to diverse causes but commonly driven via TRPA1.

2008 GRC Iron Sulfur Enzymes-Conference to be held June 8-13, 2008

Energy Technology Data Exchange (ETDEWEB)

Cramer, Stephen [Univ. of California, Davis, CA (United States); Gray, Nancy Ryan [Gordon Research Conferences, West Kingston, RI (United States)

2009-01-01

Iron-sulfur proteins are among the most common and ancient enzymes and electron-transfer agents in nature. They play key roles in photosynthesis, respiration, and the metabolism of small molecules such as H2, CO, and N2. The Iron Sulfur Enzyme Gordon Research Conference evolved from an earlier GRC on Nitrogen Fixation that began in 1994. The scope of the current meeting has broadened to include all enzymes or metalloproteins in which Fe-S bonds play a key role. This year's meeting will focus on the biosynthesis of Fe-S clusters, as well as the structure and mechanism of key Fe-S enzymes such as hydrogenase, nitrogenase and its homologues, radical SAM enzymes, and aconitase-related enzymes. Recent progress on the role of Fe-S enzymes in health, disease, DNA/RNA-processing, and alternative bio-energy systems will also be highlighted. This conference will assemble a broad, diverse, and international group of biologists and chemists who are investigating fundamental issues related to Fe-S enzymes, on atomic, molecular, organism, and environmental scales. The topics to be addressed will include: Biosynthesis & Genomics of Fe-S Enzymes; Fundamental Fe-S Chemistry; Hydrogen and Fe-S Enzymes; Nitrogenase & Homologous Fe-S Enzymes; Fe-S Enzymes in Health & Disease; Radical SAM and Aconitase-Related Fe-S Enzymes; Fe-S Enzymes and Synthetic Analogues in BioEnergy; and Fe-S Enzymes in Geochemistry and the Origin of Life.

Effect of environment on the propagation of electromagnetic waves in GRC 408E digital radiorelay devices

Directory of Open Access Journals (Sweden)

Vojkan M. Radonjić

2011-01-01

Full Text Available Quality transmission of digital signals from a transmitting radio-relay device to a receiving one depends on the impact of environmental effects on the propagation of electromagnetic waves. In this paper some of the most important effects are explained and modeled, especially those characteristic for the frequency range within which the GRC 408E operates. The modeling resulted in the conclusions about the quality of transmission of digital signals in the GRC 408E radio-relay equipment. Propagation of electromagnetic waves A radio-relay link is achieved by direct electromagnetic waves, provided there is a line of sight between the transmitting and receiving antenna of a radio-relay device. Electromagnetic waves on the road are exposed to various environmental influences causing phenomena such as bending, reflection, refraction, absorption and multiple propagation. Due to these environmental effects, the quality of information transmission is not satisfactory and a radio-relay link is not reliable. The approach to the analysis of the quality of links in digital radiorelay devices is different from the one in analog radio-relay devices. Therefore, the quality is seen through errors in the received bit ( BER , the propagation conditions are taken into account, a reservation for the fading is determined by other means, etc.. Phenomena which accompany the propagation of electromagnetic waves in digital radio-relay links The propagation of direct EM waves is followed by the following phenomena: - attenuation due to propagation, - diffraction (changing table, - refraction (refraction, - reflection (refusing, - absorption (absorption and - multiple wave propagation. Each of these has a negative effect on the quality of the received signal at the receiving antenna of the radio-relay device. Attenuation due to propagation of electromagnetic waves The main parameter for evaluating the quality of radio-relay links is the level of the field at the reception

Is it all about the money? A qualitative exploration of the effects of performance-based financial incentives on Zimbabwe's voluntary male medical circumcision program.

Directory of Open Access Journals (Sweden)

Caryl Feldacker

Full Text Available In 2013, Zimbabwe's voluntary medical male circumcision (VMMC program adopted performance-based financing (PBF to speed progress towards ambitious VMMC targets. The $25 USD PBF intended to encourage low-paid healthcare workers to remain in the public sector and to strengthen the public healthcare system. The majority of the incentive supports healthcare workers (HCWs who perform VMMC alongside other routine services; a small portion supports province, district, and facility levels.This qualitative study assessed the effect of the PBF on HCW motivation, satisfaction, and professional relationships. The study objectives were to: 1 Gain understanding of the advantages and disadvantages of PBF at the HCW level; 2 Gain understanding of the advantages and disadvantages of PBF at the site level; and 3 Inform scale up, modification, or discontinuation of PBF for the national VMMC program. Sixteen focus groups were conducted: eight with HCWs who received PBF for VMMC and eight with HCWs in the same clinics who did not work in VMMC and, therefore, did not receive PBF. Fourteen key informant interviews ascertained administrator opinion.Findings suggest that PBF appreciably increased motivation among VMMC teams and helped improve facilities where VMMC services are provided. However, PBF appears to contribute to antagonism at the workplace, creating divisiveness that may reach beyond VMMC. PBF may also cause distortion in the healthcare system: HCWs prioritized incentivized VMMC services over other routine duties. To reduce workplace tension and improve the VMMC program, participants suggested increasing HCW training in VMMC to expand PBF beneficiaries and strengthening integration of VMMC services into routine care.In the low-resource, short-staffed context of Zimbabwe, PBF enabled rapid VMMC scale up and achievement of ambitious targets; however, side effects make PBF less advantageous and sustainable than envisioned. Careful consideration is warranted in

Percent body fat is a better predictor of cardiovascular risk factors than body mass index

Energy Technology Data Exchange (ETDEWEB)

Zeng, Qiang; Dong, Sheng-Yong; Sun, Xiao-Nan; Xie, Jing; Cui, Yi [International Medical Center, Chinese PLA General Hospital, Beijing (China)

2012-04-20

The objective of the present study was to evaluate the predictive values of percent body fat (PBF) and body mass index (BMI) for cardiovascular risk factors, especially when PBF and BMI are conflicting. BMI was calculated by the standard formula and PBF was determined by bioelectrical impedance analysis. A total of 3859 ambulatory adult Han Chinese subjects (2173 males and 1686 females, age range: 18-85 years) without a history of cardiovascular diseases were recruited from February to September 2009. Based on BMI and PBF, they were classified into group 1 (normal BMI and PBF, N = 1961), group 2 (normal BMI, but abnormal PBF, N = 381), group 3 (abnormal BMI, but normal PBF, N = 681), and group 4 (abnormal BMI and PBF, N = 836). When age, gender, lifestyle, and family history of obesity were adjusted, PBF, but not BMI, was correlated with blood glucose and lipid levels. The odds ratio (OR) and 95% confidence interval (CI) for cardiovascular risk factors in groups 2 and 4 were 1.88 (1.45-2.45) and 2.06 (1.26-3.35) times those in group 1, respectively, but remained unchanged in group 3 (OR = 1.32, 95%CI = 0.92-1.89). Logistic regression models also demonstrated that PBF, rather than BMI, was independently associated with cardiovascular risk factors. In conclusion, PBF, and not BMI, is independently associated with cardiovascular risk factors, indicating that PBF is a better predictor.

Percent body fat is a better predictor of cardiovascular risk factors than body mass index

International Nuclear Information System (INIS)

Zeng, Qiang; Dong, Sheng-Yong; Sun, Xiao-Nan; Xie, Jing; Cui, Yi

2012-01-01

The objective of the present study was to evaluate the predictive values of percent body fat (PBF) and body mass index (BMI) for cardiovascular risk factors, especially when PBF and BMI are conflicting. BMI was calculated by the standard formula and PBF was determined by bioelectrical impedance analysis. A total of 3859 ambulatory adult Han Chinese subjects (2173 males and 1686 females, age range: 18-85 years) without a history of cardiovascular diseases were recruited from February to September 2009. Based on BMI and PBF, they were classified into group 1 (normal BMI and PBF, N = 1961), group 2 (normal BMI, but abnormal PBF, N = 381), group 3 (abnormal BMI, but normal PBF, N = 681), and group 4 (abnormal BMI and PBF, N = 836). When age, gender, lifestyle, and family history of obesity were adjusted, PBF, but not BMI, was correlated with blood glucose and lipid levels. The odds ratio (OR) and 95% confidence interval (CI) for cardiovascular risk factors in groups 2 and 4 were 1.88 (1.45-2.45) and 2.06 (1.26-3.35) times those in group 1, respectively, but remained unchanged in group 3 (OR = 1.32, 95%CI = 0.92-1.89). Logistic regression models also demonstrated that PBF, rather than BMI, was independently associated with cardiovascular risk factors. In conclusion, PBF, and not BMI, is independently associated with cardiovascular risk factors, indicating that PBF is a better predictor

Renewable Energy: Solar Fuels GRC and GRS

Energy Technology Data Exchange (ETDEWEB)

Lewis, Nathan [California Inst. of Technology (CalTech), Pasadena, CA (United States); Gray, Nancy Ryan [Gordon Research Conferences, West Kingston, RI (United States)

2010-02-26

sources from a carbon-neutral source. Sunlight is by far the most abundant global carbon-neutral energy resource. More solar energy strikes the surface of the earth in one hour than is obtained from all of the fossil fuels consumed globally in a year. Sunlight may be used to power the planet. However, it is intermittent, and therefore it must be converted to electricity or stored chemical fuel to be used on a large scale. The 'grand challenge' of using the sun as a future energy source faces daunting challenges - large expanses of fundamental science and technology await discovery. A viable solar energy conversion scheme must result in a 10-50 fold decrease in the cost-to-efficiency ratio for the production of stored fuels, and must be stable and robust for a 20-30 year period. To reduce the cost of installed solar energy conversion systems to $0.20/peak watt of solar radiation, a cost level that would make them economically attractive in today's energy market, will require revolutionary technologies. This GRC seeks to present a forum for the underlying science needed to permit future generations to use the sun as a renewable and sustainable primary energy source. Speakers will discuss recent advances in homoogeneous and heterogeneous catalysis of multi-electron transfer processes of importance to solar fuel production, such as water oxidation and reduction, and carbon dioxide reduction. Speakers will also discuss advances in scaleably manufacturable systems for the capture and conversion of sunlight into electrical charges that can be readily coupled into, and utilized for, fuel production in an integrated system.

Structural, morphological and optical investigations on electron-beam irradiated PbF2-TeO2-B2O3-Eu2O3 glasses

Science.gov (United States)

Wagh, Akshatha; Petwal, Vikash; Dwivedi, Jishnu; Upadhyaya, V.; Raviprakash, Y.; Kamath, Sudha D.

2016-09-01

Combined structural, optical and morphological studies were carried out on Eu2O3 doped PbF2-TeO2-B2O3 glass samples, before and after being subjected to electron beam of energy 7.5 MeV. XRD confirmed the amorphous nature of the glasses even after 150 kGy electron beam irradiation. Densities of the irradiated samples showed slightly greater values when compared to their respective values before irradiation, which proved the increase in the compaction of the network. The intensities of the three prominent bands; B-O-B linkages, BO4 units and BO3 units of FT-IR spectra, of the titled glasses, showed slight decrease after electron beam irradiation. The decrement in the values of energy band gap and shift in cut-off wavelength towards red edge, proved the formation of color centers in the glass network after irradiation. The change in Hunter L values, through color measurement was a proof for the Farbe/color/absorption centers created in the glass sites after irradiation.

Block Compressed Sensing of Images Using Adaptive Granular Reconstruction

Directory of Open Access Journals (Sweden)

Ran Li

2016-01-01

Full Text Available In the framework of block Compressed Sensing (CS, the reconstruction algorithm based on the Smoothed Projected Landweber (SPL iteration can achieve the better rate-distortion performance with a low computational complexity, especially for using the Principle Components Analysis (PCA to perform the adaptive hard-thresholding shrinkage. However, during learning the PCA matrix, it affects the reconstruction performance of Landweber iteration to neglect the stationary local structural characteristic of image. To solve the above problem, this paper firstly uses the Granular Computing (GrC to decompose an image into several granules depending on the structural features of patches. Then, we perform the PCA to learn the sparse representation basis corresponding to each granule. Finally, the hard-thresholding shrinkage is employed to remove the noises in patches. The patches in granule have the stationary local structural characteristic, so that our method can effectively improve the performance of hard-thresholding shrinkage. Experimental results indicate that the reconstructed image by the proposed algorithm has better objective quality when compared with several traditional ones. The edge and texture details in the reconstructed image are better preserved, which guarantees the better visual quality. Besides, our method has still a low computational complexity of reconstruction.

Leak before break evaluation for main steam piping system made of SA106 Gr.C

Energy Technology Data Exchange (ETDEWEB)

Yang, Kyoung Mo; Jee, Kye Kwang; Pyo, Chang Ryul; Ra, In Sik [Korea Power Engineering Company, Seoul (Korea, Republic of)

1997-04-01

The basis of the leak before break (LBB) concept is to demonstrate that piping will leak significantly before a double ended guillotine break (DEGB) occurs. This is demonstrated by quantifying and evaluating the leak process and prescribing safe shutdown of the plant on the basis of the monitored leak rate. The application of LBB for power plant design has reduced plant cost while improving plant integrity. Several evaluations employing LBB analysis on system piping based on DEGB design have been completed. However, the application of LBB on main steam (MS) piping, which is LBB applicable piping, has not been performed due to several uncertainties associated with occurrence of steam hammer and dynamic strain aging (DSA). The objective of this paper is to demonstrate the applicability of the LBB design concept to main steam lines manufactured with SA106 Gr.C carbon steel. Based on the material properties, including fracture toughness and tensile properties obtained from the comprehensive material tests for base and weld metals, a parametric study was performed as described in this paper. The PICEP code was used to determine leak size crack (LSC) and the FLET code was used to perform the stability assessment of MS piping. The effects of material properties obtained from tests were evaluated to determine the LBB applicability for the MS piping. It can be shown from this parametric study that the MS piping has a high possibility of design using LBB analysis.

HLA-A*0201-restricted CTL epitope of a novel osteosarcoma antigen, papillomavirus binding factor

Directory of Open Access Journals (Sweden)

Tsukahara Tomohide

2009-06-01

Full Text Available Abstract Background To develop peptide-based immunotherapy for osteosarcoma, we previously identified papillomavirus binding factor (PBF as a CTL-defined osteosarcoma antigen in the context of HLA-B55. However, clinical application of PBF-based immunotherapy requires identification of naturally presented CTL epitopes in osteosarcoma cells in the context of more common HLA molecules such as HLA-A2. Methods Ten peptides with the HLA-A*0201 binding motif were synthesized from the amino acid sequence of PBF according to the BIMAS score and screened with an HLA class I stabilization assay. The frequency of CTLs recognizing the selected PBF-derived peptide was determined in peripheral blood of five HLA-A*0201+ patients with osteosarcoma using limiting dilution (LD/mixed lymphocyte peptide culture (MLPC followed by tetramer-based frequency analysis. Attempts were made to establish PBF-specific CTL clones from the tetramer-positive CTL pool by a combination of limiting dilution and single-cell sorting. The cytotoxicity of CTLs was assessed by 51Cr release assay. Results Peptide PBF A2.2 showed the highest affinity to HLA-A*0201. CD8+ T cells reacting with the PBF A2.2 peptide were detected in three of five patients at frequencies from 2 × 10-7 to 5 × 10-6. A tetramer-positive PBF A2.2-specific CTL line, 5A9, specifically lysed allogeneic osteosarcoma cell lines that expressed both PBF and either HLA-A*0201 or HLA-A*0206, autologous tumor cells, and T2 pulsed with PBF A2.2. Five of 12 tetramer-positive CTL clones also lysed allogeneic osteosarcoma cell lines expressing both PBF and either HLA-A*0201 or HLA-A*0206 and T2 pulsed with PBF A2.2. Conclusion These findings indicate that PBF A2.2 serves as a CTL epitope on osteosarcoma cells in the context of HLA-A*0201, and potentially, HLA-A*0206. This extends the availability of PBF-derived therapeutic peptide vaccines for patients with osteosarcoma.

Crowding out or no crowding out? A Self-Determination Theory approach to health worker motivation in performance-based financing.

Science.gov (United States)

Lohmann, Julia; Houlfort, Nathalie; De Allegri, Manuela

2016-11-01

Performance-based financing (PBF) is a common health system reform approach in low and middle income countries at present. Although increasing evidence on the effectiveness of PBF and knowledge of principles of good design are available, research is still lacking in regards to other aspects. Among these are a yet limited understanding of the complex role of health worker motivation in PBF and of potential side effects, for instance on intrinsic motivation. Our article aims to support meaningful future research by advancing the theoretical discussion around health worker motivation and PBF. We argue that an in-depth understanding of the motivational mechanisms and consequences of PBF at health worker level are of high practical relevance and should be at the heart of the PBF research agenda, and that predominant unidimensional conceptualizations of health worker motivation and descriptive rather than explanatory research approaches are insufficient to fully understand whether, how, and why PBF schemes alter health workers' motivational structures, mindsets, affect, and behavior. We introduce and apply Self-Determination Theory to the context of PBF as a valuable theoretical framework for future empirical exploration. From this, we conclude that PBF interventions are unlikely to have a generally adverse effect on intrinsic motivation as feared by parts of the PBF community. Rather, we posit that PBF can have positive and negative effects on both intrinsic and extrinsic motivation, to varying degrees depending on the specific design, implementation, and results of a particular intervention and on health workers' perceptions and evaluations of it. Copyright © 2016 Elsevier Ltd. All rights reserved.

Study on placental blood flow in late pregnancy by intravenous sup(99m)Tc method

International Nuclear Information System (INIS)

Kitagawa, Hiroshi

1985-01-01

A method for the continuous recording of uteroplacental blood flow (PBF) in late pregnancies by using sup(99m)Tc-albumin has been described. 1) The PBF curve of toxemia of pregnancy has been plotted to indicate small artery spasm in proving ischemic necrosis of placenta. 2) In the PBF of placental insufficiency evidenced by the values for urinary E 3 , an unfavorable build-up and a delayed build-up time were observed. The pathologic diagnosis showed condensation, fusion and necrosis of villi. 3) In the PBF in which a intrauterine fetal death (IUFD) was caused by placental factors, a sudden change in the PBF was observed showing the presence of an ischemia. 4) In the PBF of pregnancy with diabetes, a large wave pattern change was observed indicating a decrease in the PBF. The pathologic diagnosis showed the fusion, hyalinization and necrosis of villi. 5) The PBF wave patterns were classified into four kinds: (1) normal pattern, (2) angio-spasm pattern, (3) delayed build-up pattern, (4) circulation pattern. It has become clear that these abnormal wave patterns are frequently observed in toxemia of pregnancy, placental insufficiency and pregnancy with diabetes. (author)

Performance-based financing: the same is different.

Science.gov (United States)

Renmans, Dimitri; Holvoet, Nathalie; Criel, Bart; Meessen, Bruno

2017-07-01

Although it is increasingly acknowledged within the Performance-Based Financing (PBF) research community that PBF is more than just payments based on outputs verified for quality, this narrow definition of PBF is still very present in many studies and evaluations. This leads to missed opportunities, misunderstandings and an unhelpful debate. Therefore, we reinforce the claim that PBF should be viewed as a reform package focused on targeted services with many different aspects that go beyond the health worker level. Failing to acknowledge the importance of the different elements of PBF negatively influences the task of practitioners, researchers and policymakers alike. After making the case for this wider definition, we propose three research pathways (describing, understanding and framing PBF) and give a short and tentative starting point for future research, leaving the floor open for more in-depth discussions. From these three vantage points it appears that when it comes to PBF 'the same is different'. Notwithstanding the increased complexity due to the use of the wider definition, progress on these three different research pathways will strongly improve our knowledge, lead to better adapted PBF programs and create a more nuanced debate on PBF. © The Author 2017. Published by Oxford University Press in association with The London School of Hygiene and Tropical Medicine. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Local Stakeholders’ Perceptions about the Introduction of Performance-Based Financing in Benin: A Case Study in Two Health Districts

Directory of Open Access Journals (Sweden)

Elisabeth Paul

2014-09-01

Full Text Available Background Performance-Based Financing (PBF has been advanced as a solution to contribute to improving the performance of health systems in developing countries. This is the case in Benin. This study aims to analyse how two PBF approaches, piloted in Benin, behave during implementation and what effects they produce, through investigating how local stakeholders perceive the introduction of PBF, how they adapt the different approaches during implementation, and the behavioural interactions induced by PBF. Methods The research rests on a socio-anthropological approach and qualitative methods. The design is a case study in two health districts selected on purpose. The selection of health facilities was also done on purpose, until we reached saturation of information. Information was collected through observation and semi-directive interviews supported by an interview guide. Data was analysed through contents and discourse analysis. Results The Ministry of Health (MoH strongly supports PBF, but it is not well integrated with other ongoing reforms and processes. Field actors welcome PBF but still do not have a sense of ownership about it. The two PBF approaches differ notably as for the organs in charge of verification. Performance premiums are granted according to a limited number of quantitative indicators plus an extensive qualitative checklist. PBF matrices and verification missions come in addition to routine monitoring. Local stakeholders accommodate theoretical approaches. Globally, staff is satisfied with PBF and welcomes additional supervision and training. Health providers reckon that PBF forces them to depart from routine, to be more professional and to respect national norms. A major issue is the perceived unfairness in premium distribution. Even if health staff often refer to financial premiums, actually the latter are probably too weak—and ‘blurred’—to have a lasting inciting effect. It rather seems that PBF motivates health

How does performance-based financing affect health workers' intrinsic motivation? A Self-Determination Theory-based mixed-methods study in Malawi.

Science.gov (United States)

Lohmann, Julia; Muula, Adamson S; Houlfort, Nathalie; De Allegri, Manuela

2018-07-01

"Intrinsic motivation crowding out", the erosion of high-quality, sustainable motivation through the introduction of financial incentives, is one of the most frequently discussed but yet little researched potential unfavorable consequence of Performance-based Financing (PBF). We used the opportunity of the introduction of PBF in Malawi to investigate whether and how PBF affected intrinsic motivation, using a mixed-methods research design theoretically grounded in Self-Determination Theory (SDT). The quantitative component served to estimate the impact of PBF on intrinsic motivation, relying on a controlled pre- and post-test design, with data collected from health workers in 23 intervention and 10 comparison facilities before (March/April 2013; n = 70) and approximately two years after (June/July 2015; n = 71) the start of the intervention. The qualitative component, relying on in-depth interviews with health workers in selected intervention facilities one (April 2014; n = 21) and two (September 2015; n = 20) years after the start of PBF, served to understand how PBF did or did not bring about change in intrinsic motivation. Specifically, it allowed us to examine how the various motivation-relevant elements and consequences of PBF impacted health workers' basic psychological needs for autonomy, competence, and relatedness, which SDT postulates as central to intrinsic motivation. Our results suggest that PBF did not affect health workers' overall intrinsic motivation levels, with the intervention having had both positive and negative effects on psychological needs satisfaction. To maximize positive PBF effects on intrinsic motivation, our results underline the potential value of explicit strategies to mitigate unintended negative impact of unavoidable design, implementation, and contextual challenges, for instance by building autonomy support activities into PBF designs. Copyright © 2018 Elsevier Ltd. All rights reserved.

Residual stress prediction in a powder bed fusion manufactured Ti6Al4V hip stem

Science.gov (United States)

Barrett, Richard A.; Etienne, Titouan; Duddy, Cormac; Harrison, Noel M.

2017-10-01

Powder bed fusion (PBF) is a category of additive manufacturing (AM) that is particularly suitable for the production of 3D metallic components. In PBF, only material in the current build layer is at the required melt temperature, with the previously melted and solidified layers reducing in temperature, thus generating a significant thermal gradient within the metallic component, particularly for laser based PBF components. The internal thermal stresses are subsequently relieved in a post-processing heat-treatment step. Failure to adequately remove these stresses can result in cracking and component failure. A prototype hip stem was manufactured from Ti6Al4V via laser PBF but was found to have fractured during over-seas shipping. This study examines the evolution of thermal stresses during the laser PBF manufacturing and heat treatment processes of the hip stem in a 2D finite element analysis (FEA) and compares it to an electron beam PBF process. A custom written script for the automatic conversion of a gross geometry finite element model into a thin layer- by-layer finite element model was developed. The build process, heat treatment (for laser PBF) and the subsequent cooling were simulated at the component level. The results demonstrate the effectiveness of the heat treatment in reducing PBF induced thermal stresses, and the concentration of stresses in the region that fractured.

The Effects of Performance Budgeting and Funding Programs on Graduation Rate in Public Four-Year Colleges and Universities

Directory of Open Access Journals (Sweden)

Jung-cheol Shinn

2004-05-01

Full Text Available This study was conducted to determine whether states with performance budgeting and funding (PBF programs had improved institutional performance of higher education over the five years (1997 through 2001 considered in this study. First Time in College (FTIC graduation rate was used as the measure of institutional performance. In this study, the unit of analysis is institution level and the study population is all public four-or-more-year institutions in the United States. To test PBF program effectiveness, Hierarchical Linear Modeling (HLM growth analysis was applied. According to the HLM analysis, the growth of graduation rates in states with PBF programs was not greater than in states without PBF programs. The lack of growth in institutional graduation rates, however, does not mean that PBF programs failed to achieve their goals. Policy-makers are advised to sustain PBF programs long enough until such programs bear their fruits or are proven ineffective.

Context matters (but how and why?) A hypothesis-led literature review of performance based financing in fragile and conflict-affected health systems.

Science.gov (United States)

Bertone, Maria Paola; Falisse, Jean-Benoît; Russo, Giuliano; Witter, Sophie

2018-01-01

Performance-based financing (PBF) schemes have been expanding rapidly across low and middle income countries in the past decade, with considerable external financing from multilateral, bilateral and global health initiatives. Many of these countries have been fragile and conflict-affected (FCAS), but while the influence of context is acknowledged to be important to the operation of PBF, there has been little examination of how it affects adoption and implementation of PBF. This article lays out initial hypotheses about how FCAS contexts may influence the adoption, adaption, implementation and health system effects of PBF. These are then interrogated through a review of available grey and published literature (140 documents in total, covering 23 PBF schemes). We find that PBF has been more common in FCAS contexts, which were also more commonly early adopters. Very little explanation of the rationale for its adoption, in particular in relation with the contextual features, is given in programme documents. However, there are a number of factors which could explain this, including the greater role of external actors and donors, a greater openness to institutional reform, and lower levels of trust within the public system and between government and donors, all of which favour more contractual approaches. These suggest that rather than emerging despite fragility, conditions of fragility may favour the rapid emergence of PBF. We also document few emerging adaptations of PBF to humanitarian settings and limited evidence of health system effects which may be contextually driven, but these require more in-depth analysis. Another area meriting more study is the political economy of PBF and its diffusion across contexts.

PULPAL BLOOD FLOW CHANGES IN ABUTMENT TEETH OF REMOVABLE PARTIAL DENTURES

Science.gov (United States)

Kunt, Göknil Ergün; Kökçü, Deniz; Ceylan, Gözlem; Yılmaz, Nergiz; Güler, Ahmet Umut

2009-01-01

The purpose of this study was to investigate the effect of tooth supported (TSD) and toothtissue supported (TTSD) removable partial denture wearing on pulpal blood flow (PBF) of the abutment teeth by using Laser Doppler Flowmeter (LDF). Measurements were carried out on 60 teeth of 28 patients (28 teeth and 12 patients of TTSD group, 32 teeth and 16 patients of TSD group) who had not worn any type of removable partial dentures before, had no systemic problems and were non smokers. PBF values were recorded by LDF before insertion (day 0) and after insertion of dentures at day 1, day 7 and day 30. Statistical analysis was performed by student t test and covariance analyses of repeated measurements. In the group TTSD, the mean values of PBF decreased statistically significantly at day 1 after insertion when compared with PBF values before insertion (p<0,01). There was no statistically significant difference among PBF mean values on 1st, 7th and 30th day. However, in the group TSD, there was no statistically significant difference among PBF mean values before insertion and on 1st, 7th and 30th day. In other words, PBF mean values in group TSD continued without changing statistically significant on 1st, 7th and 30th day. TTSD wearing may show negative effect on the abutment teeth due to decreasing basal PBF. PMID:20001995

Pulpal blood flow changes in abutment teeth of removable partial dentures

Directory of Open Access Journals (Sweden)

Göknil Ergün Kunt

2009-11-01

Full Text Available The purpose of this study was to investigate the effect of tooth supported (TSD and toothtissue supported (TTSD removable partial denture wearing on pulpal blood flow (PBF of the abutment teeth by using Laser Doppler Flowmeter (LDF.Measurements were carried out on 60 teeth of 28 patients (28 teeth and 12 patients of TTSD group, 32 teeth and 16 patients of TSD group who had not worn any type of removable partial dentures before, had no systemic problems and were non smokers. PBF values were recorded by LDF before insertion (day 0 and after insertion of dentures at day 1, day 7 and day 30. Statistical analysis was performed by student t test and covariance analyses of repeated measurements.In the group TTSD, the mean values of PBF decreased statistically significantly at day 1 after insertion when compared with PBF values before insertion (p<0,01. There was no statistically significant difference among PBF mean values on 1st, 7th and 30th day. However, in the group TSD, there was no statistically significant difference among PBF mean values before insertion and on 1st, 7th and 30th day. In other words, PBF mean values in group TSD continued without changing statistically significant on 1st, 7th and 30th day.TTSD wearing may show negative effect on the abutment teeth due to decreasing basal PBF.

Performance-Based Financing to Strengthen the Health System in Benin: Challenging the Mainstream Approach

Directory of Open Access Journals (Sweden)

Elisabeth Paul

2018-01-01

Full Text Available Background Performance-based financing (PBF is often proposed as a way to improve health system performance. In Benin, PBF was launched in 2012 through a World Bank-supported project. The Belgian Development Agency (BTC followed suit through a health system strengthening (HSS project. This paper analyses and draws lessons from the experience of BTC-supported PBF alternative approach – especially with regards to institutional aspects, the role of demand-side actors, ownership, and cost-effectiveness – and explores the mechanisms at stake so as to better understand how the “PBF package” functions and produces effects. Methods An exploratory, theory-driven evaluation approach was adopted. Causal mechanisms through which PBF is hypothesised to impact on results were singled out and explored. This paper stems from the co-authors’ capitalisation of experiences; mixed methods were used to collect, triangulate and analyse information. Results are structured along Witter et al framework. Results Influence of context is strong over PBF in Benin; the policy is donor-driven. BTC did not adopt the World Bank’s mainstream PBF model, but developed an alternative approach in line with its HSS support programme, which is grounded on existing domestic institutions. The main features of this approach are described (decentralised governance, peer review verification, counter-verification entrusted to health service users’ platforms, as well as its adaptive process. PBF has contributed to strengthen various aspects of the health system and led to modest progress in utilisation of health services, but noticeable improvements in healthcare quality. Three mechanisms explaining observed outcomes within the context are described: comprehensive HSS at district level; acting on health workers’ motivation through a complex package of incentives; and increased accountability by reinforcing dialogue with demand-side actors. Cost-effectiveness and

Efficiency of herbal medicine Dai-kenchu-to on portal blood flow in rat models

OpenAIRE

Muraoka, Izumi; Takatsuki, Mitsuhisa; Soyama, Akihiko; Yamaguchi, Izumi; Tanaka, Shiro; Tanaka, Takayuki; Kinoshita, Ayaka; Hara, Takanobu; Kuroki, Tamotsu; Eguchi, Susumu

2015-01-01

Introduction: To clarify the influence of Dai-Kenchu-To (DKT) on portal blood flow (PBF), PBF was continuously measured with Doppler ultrasound. Methods: Normal liver rats were divided into a DKT 90 mg/kg, DKT 270 mg/kg administered group, and control, while cirrhotic liver rats were divided into a DKT-LC 90 mg/kg administered group and Control-LC. The PBF was measured after the administration of either DKT or water for 60 min by laser Doppler flowmetry system. Results: The PBF in the D...

Efficiency of herbal medicine Dai-kenchu-to on portal blood flow in rat models.

Science.gov (United States)

Muraoka, Izumi; Takatsuki, Mitsuhisa; Soyama, Akihiko; Yamaguchi, Izumi; Tanaka, Shiro; Tanaka, Takayuki; Kinoshita, Ayaka; Hara, Takanobu; Kuroki, Tamotsu; Eguchi, Susumu

2015-09-01

To clarify the influence of Dai-Kenchu-To (DKT) on portal blood flow (PBF), PBF was continuously measured with Doppler ultrasound. Normal liver rats were divided into a DKT 90 mg/kg, DKT 270 mg/kg administered group, and control, while cirrhotic liver rats were divided into a DKT-LC 90 mg/kg administered group and Control-LC. The PBF was measured after the administration of either DKT or water for 60 min by laser Doppler flowmetry system. The PBF in the DKT 90 increased approximately 10 min after DKT was administrated, and elevated levels were maintained for approximately 10 min. A comparison of the increase in PBF by the calculating the area under the curve (AUC) revealed that flow was significantly higher in the DKT 90 compared to either the control or the DKT 270 (p DKT-LC and Control-LC. The AUC, revealed no significant difference between the DKT-LC and Control-LC. DKT induced an increase in PBF in normal livers; however, its effects were insufficient to increase PBF in the cirrhotic livers. No increase in the portal blood flow in the cirrhotic liver rats was probably the result of the cirrhotic liver, which had fibrotic change, and, therefore, may not have had sufficient compliance to accept the increasing blood flow volume from the intestinal tract. We suggested DKT has the potential to protect the liver by increasing PBF when the liver has either normal or mild to moderate dysfunction.

The Study of Eating Disorders and Body Image Among Elite Martial Arts Athletes

Directory of Open Access Journals (Sweden)

Morteza Taheri

2017-11-01

Full Text Available Study objective: The competitive sports environment can enhance social and cultural pressure towards having ideal body weight in weight-sensitive sports. The close relationship between body image and performance makes the elite athletes vulnerable to eating disorders. Thus, the purpose of this research was to study eating disorders and body image among weight-class elite athletes. Methods: A cross-sectional study was carried out with elite martial arts athletes (Karate, Taekwondo, and Judo who were considered to be of higher risk for eating disorders. 63 elite martial arts male athletes (18.59 ± 5.29 yrs, and 63 non-athlete persons (17.3 ± 3.4 yrs were recruited. Body Mass Index (BMI, Waist Hip Ratio (WHR, and Percent Body Fat (PBF were measured using caliper and meter. Eating Disorder Diagnosis Scale (EDDS and Body Image Rating Scale (BIRS were used to study eating disorders and body image among elite martial arts athletes. Results: no sign of clinical EDDS were found among the investigated athletes, and non-athletes. There were significant differences in total score of EDDS (p=0.001, eating disorder and weight concern subscales (respectively p=0.012, p=0.001 in athletes and non-athletes. Furthermore, compared with the non-athlete group, elite athlete group with middle, good, and great body images scored higher on total score and all subscales of EDDS (p ≤ 0.05. Conclusion: The results from our study show the presence of worriment about eating disorder especially body weight and eating concern in elite athletes and the early detection of it may prevent progression to severe eating disorders.

Quantitative analysis of pulmonary perfusion using time-resolved parallel 3D MRI - initial results

International Nuclear Information System (INIS)

Fink, C.; Buhmann, R.; Plathow, C.; Puderbach, M.; Kauczor, H.U.; Risse, F.; Ley, S.; Meyer, F.J.

2004-01-01

Purpose: to assess the use of time-resolved parallel 3D MRI for a quantitative analysis of pulmonary perfusion in patients with cardiopulmonary disease. Materials and methods: eight patients with pulmonary embolism or pulmonary hypertension were examined with a time-resolved 3D gradient echo pulse sequence with parallel imaging techniques (FLASH 3D, TE/TR: 0.8/1.9 ms; flip angle: 40 ; GRAPPA). A quantitative perfusion analysis based on indicator dilution theory was performed using a dedicated software. Results: patients with pulmonary embolism or chronic thromboembolic pulmonary hypertension revealed characteristic wedge-shaped perfusion defects at perfusion MRI. They were characterized by a decreased pulmonary blood flow (PBF) and pulmonary blood volume (PBV) and increased mean transit time (MTT). Patients with primary pulmonary hypertension or eisenmenger syndrome showed a more homogeneous perfusion pattern. The mean MTT of all patients was 3.3 - 4.7 s. The mean PBF and PBV showed a broader interindividual variation (PBF: 104-322 ml/100 ml/min; PBV: 8 - 21 ml/100 ml). Conclusion: time-resolved parallel 3D MRI allows at least a semi-quantitative assessment of lung perfusion. Future studies will have to assess the clinical value of this quantitative information for the diagnosis and management of cardiopulmonary disease. (orig.) [de

Body Mass Index, Waist Circumference, Body Fat, Fasting Blood Glucose in a Sample of Moroccan Adolescents Aged 11–17 Years

Science.gov (United States)

Mehdad, Slimane; Hamrani, Abdeslam; El Kari, Khalid; El Hamdouchi, Asmaa; Barakat, Amina; El Mzibri, Mohamed; Mokhtar, Najat; Aguenaou, Hassan

2012-01-01

Objectives. The study aimed to assess the relationship between body fat and each of body mass index (BMI) and waist circumference (WC), and to test the effectiveness of fat mass (FM), percent of body fat (PBF), BMI, and WC in predicting high levels of fasting blood glucose (FBG). Methods. A total of 167 adolescents aged 11–17 years were recruited from Rabat region. BMI and WC were determined using standard equipments. FM and PBF were derived from isotope dilution technique. FBG was determined by the hexokinase method. Results. Regardless of the weight status, BMI showed a strong positive correlation with FM and PBF in both genders. WC was significantly correlated with FM in boys and girls, and with PBF in different groups of girls and boys of the study sample. However, there was no significant relationship between WC and PBF in normal weight and overweight-obese groups of boys. FBG was highly correlated with FM and PBF in girls of the study sample and in overweight-obese girls. Similar significant relationship between FBG and both BMI and WC was observed in overweight-obese girls, while there was no significant association between FBG and other variables in boys and normal-weight girls. Conclusion. BMI and WC were closely associated with FM and PBF, respectively. However, the degree of these associations depends on gender and weight status. BMI may provide a better proxy estimate of overall adiposity than WC; nevertheless, both of them would appear to be a reasonable surrogate for FM and PBF as screening tools to identify adolescents at risk of developing excess body fat and high level of FBG. PMID:22175010

Changes in Maxillary Canine Pulpal Blood Flow During Dentoalveolar Distraction Osteogenesis.

Science.gov (United States)

Ersahan, Seyda; Sabuncuoglu, Fidan Alakus

2016-05-01

The aim of this study was to assess the effects of dentoalveolar distraction osteogenesis (DD) on the pulpal blood flow (PBF) of maxillary canines. A laser Doppler flowmeter (LDF) was used to measure PBF in maxillary canines of 10 patients undergoing DD (study group) and 10 nonsurgical subjects who received no orthodontic treatment (control group). PBF was measured at baseline, at 4 and 7 days postoperatively, at the end of distraction and at the end of consolidation in the study group and at similar time-points in nonsurgical control subjects. Data were analyzed using paired and Student t tests, with the significance level set at 0.05. Study findings showed that baseline PBF values did not differ significantly between groups. PBF in the control group did not vary over time; however, in the study group, an initial decrease in PBF was observed at 4 days postoperatively and was followed by a gradual increase to preoperative levels at the end of distraction. During the DD latency period, there appears to be a short-lived ischemic phase when perfusion of pulp tissue declines; however, blood-flow returns to normal by the end of distraction.

Reduced pulmonary blood flow in regions of injury 2 hours after acid aspiration in rats.

Science.gov (United States)

Richter, Torsten; Bergmann, Ralf; Musch, Guido; Pietzsch, Jens; Koch, Thea

2015-01-01

Aspiration-induced lung injury can decrease gas exchange and increase mortality. Acute lung injury following acid aspiration is characterized by elevated pulmonary blood flow (PBF) in damaged lung areas in the early inflammation stage. Knowledge of PBF patterns after acid aspiration is important for targeting intravenous treatments. We examined PBF in an experimental model at a later stage (2 hours after injury). Anesthetized Wistar-Unilever rats (n = 5) underwent unilateral endobronchial instillation of hydrochloric acid. The PBF distribution was compared between injured and uninjured sides and with that of untreated control animals (n = 6). Changes in lung density after injury were measured using computed tomography (CT). Regional PBF distribution was determined quantitatively in vivo 2 hours after acid instillation by measuring the concentration of [(68)Ga]-radiolabeled microspheres using positron emission tomography. CT scans revealed increased lung density in areas of acid aspiration. Lung injury was accompanied by impaired gas exchange. Acid aspiration decreased the arterial pressure of oxygen from 157 mmHg [139;165] to 74 mmHg [67;86] at 20 minutes and tended toward restoration to 109 mmHg [69;114] at 110 minutes (P < 0.001). The PBF ratio of the middle region of the injured versus uninjured lungs of the aspiration group (0.86 [0.7;0.9], median [25%;75%]) was significantly lower than the PBF ratio in the left versus right lung of the control group (1.02 [1.0;1.05]; P = 0.016). The PBF pattern 2 hours after aspiration-induced lung injury showed a redistribution of PBF away from injured regions that was likely responsible for the partial recovery from hypoxemia over time. Treatments given intravenously 2 hours after acid-induced lung injury may not preferentially reach the injured lung regions, contrary to what occurs during the first hour of inflammation. Please see related article: http://dx.doi.org/10.1186/s12871-015-0014-z.

Motivating health workers up to a limit: partial effects of performance-based financing on working environments in Nigeria.

Science.gov (United States)

Bhatnagar, Aarushi; George, Asha S

2016-09-01

In 2012, the Nigerian government launched performance-based financing (PBF) in three districts providing financial incentives to health workers based on the quantity and quality of service provision. They were given autonomy to use funds for operational costs and performance bonuses. This study aims to understand changes in perceived motivation among health workers with the introduction of PBF in Wamba district, Nigeria. The study used a qualitative research design to compare perceptions of health workers in facilities receiving PBF payments in the pilot district of Wamba to those that were not. In-depth semi-structured interviews (n = 39) were conducted with health workers from PBF and non-PBF facilities along with managers of the PBF project. Framework analysis was used to identify patterns and variations in responses. Facility records were collated and triangulated with qualitative data. Health workers receiving PBF payments reported to be 'awakened' by performance bonuses and improved working environments including routine supportive supervision and availability of essential drugs. They recounted being more punctual, hard working and proud of providing better services to their communities. In comparison, health workers in non-PBF facilities complained about the dearth of basic equipment and lack of motivating strategies. However, health workers from both sets of facilities considered there to be a severe shortage of manpower resulting in excessive workload, fatigue and general dissatisfaction. PBF strategies can succeed in motivating health workers by bringing about a change in incentives and working conditions. However, such programmes need to be aligned with human resource reforms including timely recruitment and appropriate distribution of health workers to prevent burn out and attrition. As people working on the frontline of constrained health systems, health workers are responsive to improved incentives and working conditions, but need more

Impact of performance-based financing on primary health care services in Haiti.

Science.gov (United States)

Zeng, Wu; Cros, Marion; Wright, Katherine D; Shepard, Donald S

2013-09-01

To strengthen Haiti's primary health care (PHC) system, the country first piloted performance-based financing (PBF) in 1999 and subsequently expanded the approach to most internationally funded non-government organizations. PBF complements support (training and technical assistance). This study evaluates (a) the separate impact of PBF and international support on PHC's service delivery; (b) the combined impact of PBF and technical assistance on PHC's service delivery; and (c) the costs of PBF implementation in Haiti. To minimize the risk of facilities neglecting potential non-incentivized services, the incentivized indicators were randomly chosen at the end of each year. We obtained quantities of key services from four departments for 217 health centres (15 with PBF and 202 without) from 2008 through 2010, computed quarterly growth rates and analysed the results using a difference-in-differences approach by comparing the growth of incentivized and non-incentivized services between PBF and non-PBF facilities. To interpret the statistical analyses, we also interviewed staff in four facilities. Whereas international support added 39% to base costs of PHC, incentive payments added only 6%. Support alone increased the quantities of PHC services over 3 years by 35% (2.7%/quarter). However, support plus incentives increased these amounts by 87% over 3 years (5.7%/quarter) compared with facilities with neither input. Incentives alone was associated with a net 39% increase over this period, and more than doubled the growth of services (P < 0.05). Interview findings found no adverse impacts and, in fact, indicated beneficial impacts on quality. Incentives proved to be a relatively inexpensive, well accepted and very effective complement to support, suggesting that a small amount of money, strategically used, can substantially improve PHC. Haiti's experience, after more than a decade of use, indicates that incentives are an effective tool to strengthen PHC.

Light Microscopy Module (LMM)-Emulator

Science.gov (United States)

Levine, Howard G.; Smith, Trent M.; Richards, Stephanie E.

2016-01-01

The Light Microscopy Module (LMM) is a microscope facility developed at Glenn Research Center (GRC) that provides researchers with powerful imaging capability onboard the International Space Station (ISS). LMM has the ability to have its hardware recongured on-orbit to accommodate a wide variety of investigations, with the capability of remotely acquiring and downloading digital images across multiple levels of magnication.

The impact of the Bolsa Família Program on food consumption: a comparative study of the southeast and northeast regions of Brazil.

Science.gov (United States)

Sperandio, Naiara; Rodrigues, Cristiana Tristão; Franceschini, Sylvia do Carmo Castro; Priore, Silvia Eloiza

2017-06-01

The aim of this study was to evaluate the impact of the Bolsa Família Program (PBF) on food consumption in the northeast and southeast regions of Brazil. The database was obtained from the individual food consumption module of the Household Budget Survey conducted in 2008-09. Consumption was assessed through two food records. The food was categorized into four groups: fresh or minimally processed food; culinary ingredients; processed food; and ultra-processed food. To analyze the impact, the propensity score matching method was used, which compares the individual recipients and non-recipients of the PBF in relation to a group of socioeconomic characteristics. After the propensity score was calculated, the impact of the PBF was estimated through the nearest-neighbor matching algorithm. In both regions, more than 60% of the daily total calories consumed by PBF recipients came from foods that had not undergone industrial processing. The recipients of PBF had a low level of consumption of processed and ultra-processed food in both regions, and an increased level of consumption of fresh or minimally processed food in the northeast. The results indicate the importance of adopting intersectoral policies in parallel to the PBF in order to strengthen healthy eating practices.

An evaluation of the feasibility of assessment of volume perfusion for the whole lung by 128-slice spiral CT

Energy Technology Data Exchange (ETDEWEB)

Sun, Haitao [Imaging Center of Taian Central Hospital, Taian, Shandong (China); Gao, Fei; Li, Ning; Liu, Cheng [Shandong Univ., Shandong Medical Imaging Research Inst., CT Room, Shandong (China)], e-mail: liucheng491025@sina.com

2013-10-15

Background: Lung perfusion based on dynamic scanning cannot provide a quantitative assessment of the whole lung because of the limited coverage of the current computed tomography (CT) detector designs. Purpose: To evaluate the feasibility of dynamic volume perfusion CT (VPCT) of the whole lung using a 128-slice CT for the quantitative assessment and visualization of pulmonary perfusion. Material and Methods: Imaging was performed in a control group of 17 subjects who had no signs of disturbance of pulmonary function or diffuse lung disease, and 15 patients (five patients with acute pulmonary embolism and 10 with emphysema) who constituted the abnormal lung group. Dynamic VPCT was performed in all subjects, and pulmonary blood flow (PBF), pulmonary blood volume (PBV), and mean transit time (MTT) were calculated from dynamic contrast images with a coverage of 20.7 cm. Regional and volumetric PBF, PBV, and MTT were statistically evaluated and comparisons were made between the normal and abnormal lung groups. Results: Regional PBF (94.2{+-}36.5, 161.8 {+-}29.6, 185.7 {+-}38.1 and 125.5 {+-}46.1, 161.9 {+-}31.4, 169.3 {+-}51.7), PBV (6.7 {+-}2.8, 10.9 {+-}3.0, 12.9 {+-}4.5 and 9.9 {+-}4.6, 10.3 {+-}2.9, 11.9 {+-}4.5), and MTT (5.8 {+-}2.4, 4.5 {+-}1.3, 4.7 {+-}2.1 and 5.6 {+-}2.3, 4.3 {+-}1.5, 4.9 {+-}1.5) demonstrated significant differences in the gravitational and isogravitational directions in the normal lung group (P < 0.05). The PBF (154.2 {+-}30.6 vs. 94.9 {+-}15.9) and PBV (11.1 {+-}4.0 vs. 6.6 {+-}1.7) by dynamic VPCT showed significant differences between normal and abnormal lungs (P < 0.05), notwithstanding the four large lungs that had coverage > 20.7 cm. Conclusion: Dynamic VPCT of the whole lung is feasible for the quantitative assessment of pulmonary perfusion by 128-slice CT, and may in future permit the evaluation of both morphological and functional features of the whole lung in a single examination.

Mindful eating reduces impulsive food choice in adolescents and adults.

Science.gov (United States)

Hendrickson, Kelsie L; Rasmussen, Erin B

2017-03-01

The present study tested the extent to which age and obesity predicted impulsive choices for food and monetary outcomes and tested how a brief mindful-eating training would alter delay discounting for food and money choices compared with control groups. First, 172 adolescents (M age = 13.13 years) and 176 (M age = 23.33 years) adults completed the Food Choice Questionnaire (FCQ) and Monetary Choice Questionnaire (MCQ) as measures of food and money delay discounting, respectively. Then, participants returned to the lab and were randomly assigned to complete a brief mindful-eating training, watch a DVD on nutrition, or serve as a control. Participants completed the FCQ and MCQ again as a postmanipulation measure. Participants with high percent body fat (PBF) were more impulsive for food than those with low PBF. Adults with high PBF were also more impulsive for money compared with adults with low PBF; no PBF-related differences were found for adolescents. Participants in the mindful-eating group exhibited more self-controlled choices for food, but not for money. The control conditions did not exhibit changes. The study suggests that individuals with high PBF make more impulsive food choices relative to those with low PBF, which could increase the risk of obesity over time. It also is the first to demonstrate shifts in choice patterns for food and money using a brief mindful-eating training with adolescents. Mindful eating is a beneficial strategy to reduce impulsive food choice, at least temporarily, that may impede weight gain. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

Prediction of microstructure, residual stress, and deformation in laser powder bed fusion process

Science.gov (United States)

Yang, Y. P.; Jamshidinia, M.; Boulware, P.; Kelly, S. M.

2017-12-01

Laser powder bed fusion (L-PBF) process has been investigated significantly to build production parts with a complex shape. Modeling tools, which can be used in a part level, are essential to allow engineers to fine tune the shape design and process parameters for additive manufacturing. This study focuses on developing modeling methods to predict microstructure, hardness, residual stress, and deformation in large L-PBF built parts. A transient sequentially coupled thermal and metallurgical analysis method was developed to predict microstructure and hardness on L-PBF built high-strength, low-alloy steel parts. A moving heat-source model was used in this analysis to accurately predict the temperature history. A kinetics based model which was developed to predict microstructure in the heat-affected zone of a welded joint was extended to predict the microstructure and hardness in an L-PBF build by inputting the predicted temperature history. The tempering effect resulting from the following built layers on the current-layer microstructural phases were modeled, which is the key to predict the final hardness correctly. It was also found that the top layers of a build part have higher hardness because of the lack of the tempering effect. A sequentially coupled thermal and mechanical analysis method was developed to predict residual stress and deformation for an L-PBF build part. It was found that a line-heating model is not suitable for analyzing a large L-PBF built part. The layer heating method is a potential method for analyzing a large L-PBF built part. The experiment was conducted to validate the model predictions.

Relationship between body mass index and adiposity in prepubertal children: ethnic and geographic comparisons between New York City and Jinan City (China)

Science.gov (United States)

Navder, Khursheed P.; He, Qing; Zhang, Xiaojing; He, Suyuan; Gong, Luxia; Sun, Yungao; Deckelbaum, Richard J.; Thornton, John; Gallagher, Dympna

2009-01-01

Body mass index (BMI) is often used as a surrogate estimate of percent body fat in epidemiological studies. This study tested the hypothesis that BMI is representative of body fatness independent of age, sex, ethnicity, and geographic location in prepubertal children. The study sample included a total of 605 prepubertal children (275 girls and 330 boys) of which 247 were Chinese from Jinan, Shandong, Mainland China, and 358 children were from various ethnic backgrounds in New York City (NYC): 121 Caucasians, 94 African Americans, and 143 Asians (Chinese and Korean). In this cross-sectional study, dual energy X-ray absorptiometry was used to quantify total body fat (TBF) and percent body fat (PBF). Prepubertal status was assessed by the criteria of Tanner. Multiple regression models were developed with TBF and PBF as the dependent variables and BMI, age, sex, and ethnicity as independent variables. Multiple regression analysis showed that BMI alone explained 85% and 69% of between-subject variance for TBF and PBF, respectively. Sex was a significant contributor to the models (P < 0.001) with girls having higher TBF and PBF than boys. Ethnicity and geographic location were significant contributors to the model (P < 0.0001) with Asians (Jinan and NYC Asians) having higher PBF than all non-Asian groups (P < 0.0001), and Jinan Asians having higher TBF and PBF than NYC-Asians. Among prepubertal children, for the same BMI, Asians have significantly higher PBF compared with African Americans and Caucasians. Caution is warranted when applying BMI across sex and ethnic prepubertal groups. PMID:19541740

Prediction of microstructure, residual stress, and deformation in laser powder bed fusion process

Science.gov (United States)

Yang, Y. P.; Jamshidinia, M.; Boulware, P.; Kelly, S. M.

2018-05-01

Laser powder bed fusion (L-PBF) process has been investigated significantly to build production parts with a complex shape. Modeling tools, which can be used in a part level, are essential to allow engineers to fine tune the shape design and process parameters for additive manufacturing. This study focuses on developing modeling methods to predict microstructure, hardness, residual stress, and deformation in large L-PBF built parts. A transient sequentially coupled thermal and metallurgical analysis method was developed to predict microstructure and hardness on L-PBF built high-strength, low-alloy steel parts. A moving heat-source model was used in this analysis to accurately predict the temperature history. A kinetics based model which was developed to predict microstructure in the heat-affected zone of a welded joint was extended to predict the microstructure and hardness in an L-PBF build by inputting the predicted temperature history. The tempering effect resulting from the following built layers on the current-layer microstructural phases were modeled, which is the key to predict the final hardness correctly. It was also found that the top layers of a build part have higher hardness because of the lack of the tempering effect. A sequentially coupled thermal and mechanical analysis method was developed to predict residual stress and deformation for an L-PBF build part. It was found that a line-heating model is not suitable for analyzing a large L-PBF built part. The layer heating method is a potential method for analyzing a large L-PBF built part. The experiment was conducted to validate the model predictions.

Application of Glass Fiber Reinforced Cement in Exhibition Decoration Project

Science.gov (United States)

Wang, Yao

2018-02-01

Through the study of GRC material and its application field, the aesthetic characteristics and functional characteristics of GRC materials are demonstrated. The decorative application and technology of GRC material in an art exhibition center are highlighted. The design, application and construction technology of GRC curtain wall and ceiling board in the interior and exterior decoration of art exhibition hall are discussed in detail. The unique advantages of GRC materials in exhibition engineering decoration are fully reflected. In practical design application, the application principle and method are summarized, and an application procedure is formed. The research proves that GRC materials in the art of building decoration engineering has an underrated advantage.

Crystallization in lead tungsten fluorophosphate glasses

International Nuclear Information System (INIS)

Nardi, R.P.R.D.; Braz, C.E.; Cassanjes, F.C.; Poirier, G.

2014-01-01

The glass forming ability was investigated in the ternary system NaPO 3 -WO 3 -PbF 2 with a constant NaPO 3 /WO 3 ratio of 3/2 and increasing amounts of PbF 2 . It has been found that glass samples can be obtained from PbF 2 contents from 0 mole% to 60 mole%. The most lead fluoride concentrated samples (50% and 60%) were chosen for a crystallization study in order to investigate the possibility of obtaining glass-ceramics containing crystalline lead fluoride. DSC measurements allowed to determine the characteristic temperatures such as Tg, Tx, Tp and Tf. These glass samples were heat-treated near the crystallization peaks observed by thermal analysis. X-ray diffraction results of these heat-treated glasses pointed out that the dominant phase which precipitates from the glass sample containing 50% of PbF 2 is the lead fluorophosphates phase Pb 5 F(PO 4 ) 3 whereas the sample containing 60% of PbF 2 exhibits a preferential crystallization of cubic lead fluoride β-PbF 2 . (author)

Nitric oxide, prostaglandins and angiotensin II in the regulation of renal medullary blood flow during volume expansion.

Science.gov (United States)

Moreno, Carol; Llinás, María T; Rodriguez, Francisca; Moreno, Juan M; Salazar, F Javier

2016-03-01

Regulation of medullary blood flow (MBF) is essential in maintaining renal function and blood pressure. However, it is unknown whether outer MBF (OMBF) and papillary blood flow (PBF) are regulated independently when extracellular volume (ECV) is enhanced. The aim of this study was to determine whether OMBF and PBF are differently regulated and whether there is an interaction between nitric oxide (NO), prostaglandins (PGs) and angiotensin II (Ang II) in regulating OMBF and PBF when ECV is enhanced. To achieve these goals, OMBF and PBF were measured by laser-Doppler in volume-expanded rats treated with a cyclooxygenase inhibitor (meclofenamate, 3 mg/kg) and/or a NO synthesis inhibitor (L-nitro-arginine methyl ester (L-NAME), 3 μg/kg/min) and/or Ang II (10 ng/kg/min). OMBF was unchanged by NO or PGs synthesis inhibition but decreased by 36 % (P blood flows to the outer medulla and renal papilla are differently regulated and showing that there is a complex interaction between NO, PGs and Ang II in regulating OMBF and PBF when ECV is enhanced.

THX Experiment Overview

Science.gov (United States)

Wernet, Mark; Wroblewski, Adam; Locke, Randy; Georgiadis, Nick

2016-01-01

This presentation provides an overview of experiments conducted at NASA GRC to provide turbulent flow measurements needed for new turbulence model development and validation. The experiments include particle image velocimetry (PIV) and hot-wire measurements of mean flow velocity and temperature fields, as well as fluctuating components.

Capabilities of the Power Burst Facility

International Nuclear Information System (INIS)

Spencer, W.A.; Jensen, A.M.; McCardell, R.K.

1982-01-01

The unique and diverse test capabilities of the Power Burst Facility (PBF) are described in this paper. The PBF test reactor, located at the Idaho National Engineering Laboratory, simulates normal, off-normal, and accident operating conditions of light water reactor fuel rods. An overview description is given, with specific detail on design and operating characteristics of the driver core, experiment test loop, fission product detection system, test train assembly facility, and support equipment which make the testing capability of the PBF so versatile

Performance-based financing with GAVI health system strengthening funding in rural Cambodia: a brief assessment of the impact.

Science.gov (United States)

Matsuoka, Sadatoshi; Obara, Hiromi; Nagai, Mari; Murakami, Hitoshi; Chan Lon, Rasmey

2014-07-01

Though Cambodia made impressive gains in immunization coverage between the years 2000 and 2005, it recognized several health system challenges to greater coverage of immunization and sustainability. The Global Alliance for Vaccines and Immunization (GAVI) opened a Health System Strengthening (HSS) funding window in 2006. To address the health system challenges, Cambodia has been receiving the GAVI HSS fund since October 2007. The major component of the support is performance-based financing (PBF) for maternal, neonatal and child health (MNCH) services. To examine the impact of the PBF scheme on MNCH services and administrative management in rural Cambodia. Quantitative and qualitative studies were conducted in Kroch Chhmar Operational District (OD), Cambodia. Quantitative analyses were conducted on the trends of the numbers of MNCH services. A brief analysis was conducted using qualitative data. After the commencement of the PBF support, the volume of MNCH services was significantly boosted. In addition, strengthened financial and operational management was observed in the study area. However, the quality of the MNCH services was not ensured. Technical assistance, rather than the PBF scheme, was perceived by stakeholders to play a vital role in increasing the quality of the services. To improve the quality of the health services provided, it is better to include indicators on the quality of care in the PBF scheme. Mutual co-operation between PBF models and technical assistance may ensure better service quality while boosting the quantity. A robust but feasible data validation mechanism should be in place, as a PBF could incentivize inaccurate reporting. The capacity for financial management should be strengthened in PBF recipient ODs. To address the broader aspects of MNCH, a balanced input of resources and strengthening of all six building blocks of a health system are necessary. Published by Oxford University Press in association with The London School of Hygiene

Overview of NASA GRCs Green Propellant Infusion Mission Thruster Testing and Plume Diagnostics

Science.gov (United States)

Deans, Matthew C.; Reed, Brian D.; Yim, John T.; Arrington, Lynn A.; Williams, George J.; Kojima, Jun J.; McLean, Christopher H.

2014-01-01

The Green Propellant Infusion Mission (GPIM) is sponsored by NASA's Space Technology Mission Directorate (STMD) Technology Demonstration Mission (TDM) office. The goal of GPIM is to advance the technology readiness level of a green propulsion system, specifically, one using the monopropellant, AF-M315E, by demonstrating ground handling, spacecraft processing, and on-orbit operations. One of the risks identified for GPIM is potential contamination of sensitive spacecraft surfaces from the effluents in the plumes of AF-M315E thrusters. NASA Glenn Research Center (GRC) is conducting activities to characterize the effects of AF-M315E plume impingement and deposition. GRC has established individual plume models of the 22-N and 1-N thrusters that will be used on the GPIM spacecraft. The models describe the pressure, temperature, density, Mach number, and species concentration of the AF-M315E thruster exhaust plumes. The models are being used to assess the impingement effects of the AF-M315E thrusters on the GPIM spacecraft. The model simulations will be correlated with plume measurement data from Laboratory and Engineering Model 22-N, AF-M315E thrusters. The thrusters will be tested in a small rocket, altitude facility at NASA GRC. The GRC thruster testing will be conducted at duty cycles representatives of the planned GPIM maneuvers. A suite of laser-based diagnostics, including Raman spectroscopy, Rayleigh spectroscopy, Schlieren imaging, and physical probes will be used to acquire plume measurements of AFM315E thrusters. Plume data will include temperature, velocity, relative density, and species concentration. The plume measurement data will be compared to the corresponding simulations of the plume model. The GRC effort will establish a data set of AF-M315E plume measurements and a plume model that can be used for future AF-M315E applications.

The Green Propellant Infusion Mission Thruster Performance Testing for Plume Diagnostics

Science.gov (United States)

Deans, Matthew C.; Reed, Brian D.; Arrington, Lynn A.; Williams, George J.; Kojima, Jun J.; Kinzbach, McKenzie I.; McLean, Christopher H.

2014-01-01

The Green Propellant Infusion Mission (GPIM) is sponsored by NASA's Space Technology Mission Directorate (STMD) Technology Demonstration Mission (TDM) office. The goal of GPIM is to advance the technology readiness level of a green propulsion system, specifically, one using the monopropellant, AF-M315E, by demonstrating ground handling, spacecraft processing, and on-orbit operations. One of the risks identified for GPIM is potential contamination of sensitive spacecraft surfaces from the effluents in the plumes of AF-M315E thrusters. NASA Glenn Research Center (GRC) is conducting activities to characterize the effects of AF-M315E plume impingement and deposition. GRC has established individual plume models of the 22-N and 1-N thrusters that will be used on the GPIM spacecraft. The model simulations will be correlated with plume measurement data from Laboratory and Engineering Model 22-N, AF-M315E thrusters. The thrusters are currently being tested in a small rocket, altitude facility at NASA GRC. A suite of diagnostics, including Raman spectroscopy, Rayleigh spectroscopy, and Schlieren imaging are being used to acquire plume measurements of AF-M315E thrusters. Plume data will include temperature, velocity, relative density, and species concentration. The plume measurement data will be compared to the corresponding simulations of the plume model. The GRC effort will establish a data set of AF-M315E plume measurements and a plume model that can be used for future AF-M315E applications.

Effects of photoperiod on wheat growth, development and yield in CELSS

Science.gov (United States)

Yunze, Shen; Shuangsheng, Guo

2014-12-01

A Controlled Ecological Life Support System (CELSS) is a sealed system used in spaceflight in order to provide astronauts with food and O2 by plants. It is of great significance to increase the energy-using efficiency because energy is extremely deficient in the space. Therefore, the objective of this research was to increase the energy-using efficiency of wheat by regulating the photoperiod. Sixteen treatments were set in total: four photoperiods before flowering (PBF) combined with four photoperiods after flowering (PAF) of 12 h, 16 h, 20 h and 24 h. The light source was red-blue LED (90% red+10% blue). As a result, the growth period of wheat was largely extended by shorter PBF, particularly the number of days from tillering to jointing and from jointing to heading. The period from flowering to maturity was extended by shorter PAF. Shorter PBF and longer PAF could increase not only the yield but also the energy-using efficiency of wheat. As for the nutritional quality, longer photoperiod (both PBF and PAF) increased starch concentration as well as decreased protein concentration of seeds. The effects of PBF and PAF were interactional. The lighting strategy with PBF of 12 h and PAF of 24 h was proved to be the optimum photoperiod for wheat cultivation in CELSS. The mechanisms of photoperiod effect contain two aspects. Firstly, photoperiod is a signal for many processes in plant growth, particularly the process of ear differentiation. Shorter PBF promoted the ear differentiation of wheat, increasing the spikelet number, floret number and seed number and thus enhancing the yield. Secondly, longer photoperiod leads to more light energy input and longer time of photosynthesis, so that longer PAF provided more photosynthate and increased seed yield.

Performance-based financing for improving HIV/AIDS service delivery: a systematic review.

Science.gov (United States)

Suthar, Amitabh B; Nagata, Jason M; Nsanzimana, Sabin; Bärnighausen, Till; Negussie, Eyerusalem K; Doherty, Meg C

2017-01-04

Although domestic HIV/AIDS financing is increasing, international HIV/AIDS financing has plateaued. Providing incentives for the health system (i.e. performance-based financing [PBF]) may help countries achieve more with available resources. We systematically reviewed effects of PBF on HIV/AIDS service delivery to inform WHO guidelines. PubMed, WHO Index Medicus, conference databases, and clinical trial registries were searched in April 2015 for randomised trials, comparative contemporaneous studies, or time-series studies. Studies evaluating PBF in people with HIV were included when they reported service quality, access, or cost. Meta-analyses were not possible due to limited data. This study is registered with PROSPERO, number CRD42015023207. Four studies, published from 2009 to 2015 and including 173,262 people, met the eligibility criteria. All studies were from Sub-Saharan Africa. PBF did not improve individual testing coverage (relative risk [RR], 1.00, 95% confidence interval [CI] 0.89 to 1.13), improved couples testing coverage (RR 1.11, 95% CI 1.02 to 1.20), and improved pregnant women testing coverage (RR 1.29, 95% CI 1.28-1.30). PBF improved coverage of antiretrovirals in pregnant women (RR 1.55, 95% CI 1.50 to 1.59), infants (RR 1.92, 95% CI 1.84 to 2.01), and adults (RR 1.74, 1.64 to 1.85). PBF reduced attrition (RR 0.84, 95% CI 0.74 to 0.96) and treatment failure (odds ratio 0.55, 95% CI 0.32 to 0.97). Potential harms were not reported. Although the limited data suggests PBF positively affected HIV service access and quality, critical health system and governance knowledge gaps remain. More research is needed to inform national policymaking.

Quantitative lung perfusion evaluation using Fourier decomposition perfusion MRI.

Science.gov (United States)

Kjørstad, Åsmund; Corteville, Dominique M R; Fischer, Andre; Henzler, Thomas; Schmid-Bindert, Gerald; Zöllner, Frank G; Schad, Lothar R

2014-08-01

To quantitatively evaluate lung perfusion using Fourier decomposition perfusion MRI. The Fourier decomposition (FD) method is a noninvasive method for assessing ventilation- and perfusion-related information in the lungs, where the perfusion maps in particular have shown promise for clinical use. However, the perfusion maps are nonquantitative and dimensionless, making follow-ups and direct comparisons between patients difficult. We present an approach to obtain physically meaningful and quantifiable perfusion maps using the FD method. The standard FD perfusion images are quantified by comparing the partially blood-filled pixels in the lung parenchyma with the fully blood-filled pixels in the aorta. The percentage of blood in a pixel is then combined with the temporal information, yielding quantitative blood flow values. The values of 10 healthy volunteers are compared with SEEPAGE measurements which have shown high consistency with dynamic contrast enhanced-MRI. All pulmonary blood flow (PBF) values are within the expected range. The two methods are in good agreement (mean difference = 0.2 mL/min/100 mL, mean absolute difference = 11 mL/min/100 mL, mean PBF-FD = 150 mL/min/100 mL, mean PBF-SEEPAGE = 151 mL/min/100 mL). The Bland-Altman plot shows a good spread of values, indicating no systematic bias between the methods. Quantitative lung perfusion can be obtained using the Fourier Decomposition method combined with a small amount of postprocessing. Copyright © 2013 Wiley Periodicals, Inc.

Alternative methods for measuring obesity in African American women.

Science.gov (United States)

Clark, Ashley E; Taylor, Jacquelyn Y; Wu, Chun Yi; Smith, Jennifer A

2013-03-01

The use of body mass index (BMI) may not be the most appropriate measurement tool in determining obesity in diverse populations. We studied a convenience sample of 108 African American (AA) women to determine the best method for measuring obesity in this at-risk population. The purpose of this study was to determine if percent body fat (PBF) and percent body water (PBW) could be used as alternatives to BMI in predicting obesity and risk for hypertension (HTN) among AA women. After accounting for age, BMI, and the use of anti-hypertensive medication, PBF (p = 0.0125) and PBW (p = 0.0297) were significantly associated with systolic blood pressure, while BMI was not. Likewise, PBF (p = 0.0316) was significantly associated with diastolic blood pressure, while PBW and BMI were not. Thus, health care practitioners should consider alternative anthropometric measurements such as PBF when assessing obesity in AA women.

Use of the Power Burst Facility for boron neutron capture therapy

International Nuclear Information System (INIS)

Crocker, J.G.; Griebenow, M.L.; Leatham, J.

1990-01-01

A program is under development at the Idaho National Engineering Laboratory (INEL) that involves using the Power Burst Facility (PBF) for research into boron neutron capture therapy (BNCT). BNCT utilizes the ionizing energy from boron-neutron capture to stop reproduction of or destroy cells in cancerous tissue in a two-step process. The first step is to selectively concentrate a boron isotope within the tumor cell, that when activated by neutron capture emits highly ionizing, short range particles. The second step involves activation of the isotope only in the vicinity of the tumor with a narrow neutron beam. The ( 10 B[n, 4 He] 7 Li) reaction with thermal neutrons produces fission products with track lengths approximately equal to a cell diameter. The INEL program includes the modification of the PBF by the addition of a filter and treatment area. The filter will down-scatter high energy neutrons into the epithermal range and remove thermal neutrons and excessively damaging gamma components. The intense source of epithermal neutrons from PBF is considered necessary to achieve optimum therapy for deep-seated tumors with minimum damage to surface tissue. THe neutron filter conceptualized for PBF utilizes aluminum and heavy water to down-scatter neutrons into the proper energy range. Bismuth will be used for gamma shielding and cadmium will remove the thermal neutron contaminant from the beam. The INEL program leads to human clinical trials at PBF which are intended to prove that brain tumors can be successfully treated through noninvasive techniques. Further research into BNCT at PBF for other cancer types is also anticipated

[The debate concerning performance-based financing in Africa South of the Sahara: analysis of the nature].

Science.gov (United States)

Manitu, Serge Mayaka; Meessen, Bruno; Lushimba, Michel Muvudi; Macq, Jean

2015-01-01

Performance-based financing (PBF) is a strategy designed to link thefunding of health services to predetermined results. Payment by an independent strategic purchaser is subject to verification of effective achievement of health outcomes in terms ofquantity and quality. This article investigates the complex tensions observed in relation to performance based financing (PBF) and identifies some reasons for disagreement on this approach. This study was essentially qualitative. Interviews were conducted with a panel of experts on PBF mobilizing their ability to reflect on the various arguments and positions concerning this financing mechanism. To enhance our analyses, we proposed a framework based on the main reasonsfor scientific or political controversies and factors involved in their emergence. Analysis of the information collected therefore consisted of combining experts verbatim reports with corresponding factors of controversies of our framework. Graphic representations of the differences were also established. Tensions concerning PBF are based on facts (experts' interpretation ofPBF), principles and values (around each expert's conceptual framework), balances of power between experts but also inappropriate behavior in the discussion process. Viewpoints remain isolated, each individual experience and an overview are lacking, which can interfere with decision-making and maintain the Health system reform crisis. Potential solutions to reduce these tensions are proposed. Our study shows that experts have difficulties agreeing on a theoretical priority approach to PBE. A good understanding of the nature of the tensions and an improvement in the quality of dialogue will promote a real dynamic of change and the proposal of an agenda of PBF actions.

[Negotiation of a heath policy controversy: application of an indirect dialogue approach to performance-based financing in sub-Saharan Africa].

Science.gov (United States)

Manitu, Serge Mayaka; Lushimba, Michel Muvudi; Macq, Jean; Meessen, Bruno

2015-01-01

This article assesses the controversy around performance-based financing (PBF) and its contribution to the reform of health systems. It aims to reduce tensions between the different camps by restructuring the debate. Our approach was to organize an indirect dialogue between critics and supporters of PBF, based on the framework developed by Norman Daniels. This analytical framework is non-partisan and uses clear and objective criteria. The interviews were carried out in two rounds (first the critics, then the supporters) and were then analyzed. Parts of answers were regrouped according to the most common sectoral themes while also highlighting major areas of disagreement. The interviews revealed some areas of convergence around PBF; the strategy is considered to be a complementary strategy to other strategies; such as those which aim to improving financial access to health care. The analysis also revealed disagreements based on misunderstandings of claims often ascribed to PBF, or lack of sufficient evidence, or asymmetrical information between experts. Several questions polarize PBF discussions. However, better structuring of convergent and divergent areas and arguments should facilitate a synthesis, at least to some extent. Experts need to adopt an objective approach with universally accepted criteria, for the benefit of all.

Body Fat Measurements in Singaporean Adults Using Four Methods

Directory of Open Access Journals (Sweden)

Xinyan Bi

2018-03-01

Full Text Available Few studies have been conducted to measure body composition in Asian populations. In this study, we determined the percent body fat (PBF by using dual-energy X-ray absorptiometry (DEXA, air-displacement plethysmography (ADP or BOD POD, bioelectrical impedance analysis (BIA and skinfold (SKF in 445 healthy Singaporean adults. We observed that the BOD POD, BIA and SKF estimates of PBF were highly correlated with that from DEXA (as a reference method among Singaporean adults. However, they all underestimated PBF (differences of 3.9% for BOD POD, 5.6% for BIA and 12.5% for SKF. Our results filled a gap in the literature by testing the relationships between DEXA and BOD POD, BIA and SKF in a large sample with a wide range of body mass index (BMI from 16.1 to 37.5 kg/m2 and age from 21 to 69.2 years. The differences of PBF measured by different methods were dependent on age, gender and ethnicity. No significant difference was observed between DEXA and BOD POD in men aged > 40 or in BMI tertile 3. However, the mean difference between DEXA and BOD POD was significant in women. Different measuring methods of estimating PBF therefore must be cautiously interpreted.

Preliminary Investigation on Life Cycle Inventory of Powder Bed Fusion of Stainless Steel

Science.gov (United States)

Nyamekye, Patricia; Piili, Heidi; Leino, Maija; Salminen, Antti

Manufacturing of work pieces from stainless steel with laser additive manufacturing, known also as laser sintering or 3D printing may increase energy and material efficiency. The use of powder bed fusion offers advantages to make parts for dynamic applications of light weight and near-net-shape products. Due to these advantages among others, PBF may also reduce emissions and operational cost in various applications. However, there are only few life cycle assessment studies examining this subject despite its prospect to business opportunity. The application of Life Cycle Inventory (LCI) in Powder Bed Fusion (PBF) provides a distinct evaluation of material and energy consumption. LCI offers a possibility to improve knowledge of process efficiency. This study investigates effect of process sustainability in terms of raw material, energy and time consumption with PBF and CNC machining. The results of the experimental study indicated lower energy efficiency in the production process with PBF. This study revealed that specific energy consumption in PBF decreased when several components are built simultaneously than if they would be built individually. This is due to fact that energy consumption per part is lower. On the contrary, amount of energy needed to machine on part in case of CNC machining is lower when parts are done separately.

Repeatability of popliteal blood flow and lower limb vascular conductance at rest and exercise during body tilt using Doppler ultrasound

International Nuclear Information System (INIS)

Villar, R; Hughson, R L

2013-01-01

We tested the data repeatability for popliteal blood flow velocity (PBV), popliteal arterial diameter (AD pop ), popliteal blood flow (PBF) and lower limb vascular conductance (VC) at rest and exercise in three body positions, two work rates and two inspired oxygen fractions. Fifteen, eleven and ten healthy volunteers participated in the three phases of the studies. Resting protocols were performed in horizontal (HOR), 35° head-down tilt (HDT) and 45° head-up tilt (HUT) for 5 min in each body position. Participants also exercised at lower and higher power outputs (repeated plantar flexion contractions at 20% and 30% maximal voluntary contraction, respectively) in HOR, HDT and HUT and in normoxia (21%O 2 ) and hypoxia (14%O 2 ) with the same work rates and body positions. PBV and AD pop were measured by ultrasound to determine PBF, and VC was estimated by dividing PBF by muscle perfusion pressure (MPP). PBV, AD pop , PBF and VC were not different, demonstrated good agreement and consistency between the two days of testing during both rest and exercise conditions regardless of body position. Therefore, these data support the utilization of Doppler and echo Doppler ultrasound as a reproducible method to measure PBV and AD pop and consequently estimate PBF and VC responses in such conditions. (paper)

Spatial and temporal variability in the trans-Pacific migration of Pacific bluefin tuna (Thunnus orientalis) revealed by archival tags

Science.gov (United States)

Fujioka, Ko; Fukuda, Hiromu; Tei, Yaoki; Okamoto, Suguru; Kiyofuji, Hidetada; Furukawa, Seishiro; Takagi, Junichi; Estess, Ethan; Farwell, Charles J.; Fuller, Daniel W.; Suzuki, Nobuaki; Ohshimo, Seiji; Kitagawa, Takashi

2018-03-01

Archival electronic tags were internally implanted in 713 age-0 Pacific bluefin tuna (PBF) caught in their nursery waters off the southern coast of Japan and in the East China Sea over an extended study period (1995-2015) to clarify the spatial and temporal variability of their trans-Pacific migration. Two hundred twenty-five of these tagged tuna were recaptured by fisheries (31.6%), and we successfully retrieved tag data from 14 of 21 individuals recovered in the Eastern pacific. Furthermore, one archival tag recovered in the Western Pacific revealed that the individual had performed a trans-Pacific migration, so in total 21 tagged PBF were shown to have migrated to the Eastern Pacific (2.9% of the total tags released). We successfully downloaded data from 15 of these 21 archival tags, which revealed that some age-1 PBF migrate rapidly (123.9 ± 82.8 km day-1) and directly from waters offshore of Japan to the eastern Pacific (160.0°E to 130.0°W), a journey that takes an average of 2.5 months (ranging from 1.2 to 5.5 months) through relatively cool waters (14.7 ± 2.0 °C). All juvenile PBF began their trans-Pacific migration shortly after exposure to cooler water temperatures (physiological challenge for this age class. Three patterns were identified in the timing of the departure of juvenile PBF from the western Pacific: departing 12-14 months post-hatch (N = 7) in early summer (May-July), departing 17-19 months post-hatch (N = 7) in late autumn (October-December), and departing 21 months post-hatch (N = 1) in late winter (February). The PBF tagged along the southern coast of Japan (SCJ) arrived in the eastern Pacific earlier than those tagged in the East China Sea (ECS), most likely due to the shorter travel distance. Additionally, the PBF that began their trans-Pacific migration in the earlier period remained in an offshore foraging zone (the Kuroshio-Oyashio transition region) for shorter periods (2.8 months on average) and at lower latitudes (35.0�

Plasmid construction using recombination activity in the fission yeast Schizosaccharomyces pombe.

Directory of Open Access Journals (Sweden)

Ayako Chino

Full Text Available BACKGROUND: Construction of plasmids is crucial in modern genetic manipulation. As of now, the common method for constructing plasmids is to digest specific DNA sequences with restriction enzymes and to ligate the resulting DNA fragments with DNA ligase. Another potent method to construct plasmids, known as gap-repair cloning (GRC, is commonly used in the budding yeast Saccharomyces cerevisiae. GRC makes use of the homologous recombination activity that occurs within the yeast cells. Due to its flexible design and efficiency, GRC has been frequently used for constructing plasmids with complex structures as well as genome-wide plasmid collections. Although there have been reports indicating GRC feasibility in the fission yeast Schizosaccharomyces pombe, this species is not commonly used for GRC as systematic studies of reporting GRC efficiency in S. pombe have not been performed till date. METHODOLOGY/PRINCIPAL FINDINGS: We investigated GRC efficiency in S. pombe in this study. We first showed that GRC was feasible in S. pombe by constructing a plasmid that contained the LEU2 auxotrophic marker gene in vivo and showed sufficient efficiency with short homology sequences (>25 bp. No preference was shown for the sequence length from the cut site in the vector plasmid. We next showed that plasmids could be constructed in a proper way using 3 DNA fragments with 70% efficiency without any specific selections being made. The GRC efficiency with 3 DNA fragments was dramatically increased >95% in lig4Delta mutant cell, where non-homologous end joining is deficient. Following this approach, we successfully constructed plasmid vectors with leu1+, ade6+, his5+, and lys1+ markers with the low-copy stable plasmid pDblet as a backbone by applying GRC in S. pombe. CONCLUSIONS/SIGNIFICANCE: We concluded that GRC was sufficiently feasible in S. pombe for genome-wide gene functional analysis as well as for regular plasmid construction. Plasmids with different

Intramyocellular triglyceride content in man, influence of sex, obesity and glycaemic control

DEFF Research Database (Denmark)

Haugaard, Steen B; Mu, Huiling; Vaag, Allan

2009-01-01

was obtained in 2 7 obese women (body mass index (BMI) = 35.5 +/- 0.8 kg/m(2) ; mean +/- S.E.M., percentage of body fat (PBF) = 44 +/- 1, n = 7 impaired fasting glucose. n = 7 type 2 diabetes), 20 obese men (BMI = 35.8 +/- 0.8 kg/m(2): PBF = 33 +/- 1, n = 4 impaired-fasting-glucose; n = 6 type 2 diabetes......It remains unknown whether sex impacts on intramyocellular triglyceride (IMTG) in obesity. as has been shown in non-obese subjects, and if so, whether this may have implications on the association between IMTG and insulin sensitivity. Subject and methods: A Muscle biopsy from vastus lateralis......) and 12 lean sedentary healthy individuals (controls: n = 7 women, BMI = 21.8 +/- 0.7 kg/m(2), PBF = 20 +/- 2: n = 5 men, BMI = 23.6 +/- 0.5 kg/m(2). PBF = 13 +/- 2). IMTG was determined by chromatography. Results: IMTG wits increased twofold in obese women compared to obese men, lean men and lean women...

Elucidating the Relations Between Monotonic and Fatigue Properties of Laser Powder Bed Fusion Stainless Steel 316L

Science.gov (United States)

Zhang, Meng; Sun, Chen-Nan; Zhang, Xiang; Goh, Phoi Chin; Wei, Jun; Li, Hua; Hardacre, David

2018-03-01

The laser powder bed fusion (L-PBF) technique builds parts with higher static strength than the conventional manufacturing processes through the formation of ultrafine grains. However, its fatigue endurance strength σ f does not match the increased monotonic tensile strength σ b. This work examines the monotonic and fatigue properties of as-built and heat-treated L-PBF stainless steel 316L. It was found that the general linear relation σ f = mσ b for describing conventional ferrous materials is not applicable to L-PBF parts because of the influence of porosity. Instead, the ductility parameter correlated linearly with fatigue strength and was proposed as the new fatigue assessment criterion for porous L-PBF parts. Annealed parts conformed to the strength-ductility trade-off. Fatigue resistance was reduced at short lives, but the effect was partially offset by the higher ductility such that comparing with an as-built part of equivalent monotonic strength, the heat-treated parts were more fatigue resistant.

Background-Oriented Schlieren used in a hypersonic inlet test at NASA GRC

Science.gov (United States)

Clem, Michelle; Woike, Mark; Saunders, John

2016-01-01

Background Oriented Schlieren (BOS) is a derivative of the classical schlieren technology, which is used to visualize density gradients, such as shock wave structures in a wind tunnel. Changes in refractive index resulting from density gradients cause light rays to bend, resulting in apparent motion of a random background pattern. The apparent motion of the pattern is determined using cross-correlation algorithms (between no-flow and with-flow image pairs) producing a schlieren-like image. One advantage of BOS is its simplified setup which enables a larger field-of-view (FOV) than traditional schlieren systems. In the present study, BOS was implemented into the Combined Cycle Engine Large-Scale Inlet Mode Transition Experiment (CCE LIMX) in the 10x10 Supersonic Wind Tunnel at NASA Glenn Research Center. The model hardware for the CCE LIMX accommodates a fully integrated turbine based combined cycle propulsion system. To date, inlet mode transition between turbine and ramjet operation has been successfully demonstrated. High-speed BOS was used to visualize the behavior of the flow structures shock waves during unsteady inlet unstarts, a phenomenon known as buzz. Transient video images of inlet buzz were recorded for both the ramjet flow path (high speed inlet) and turbine flow path (low speed inlet). To understand the stability limits of the inlet, operation was pushed to the point of unstart and buzz. BOS was implemented in order to view both inlets simultaneously, since the required FOV was beyond the capability of the current traditional schlieren system. An example of BOS data (Images 1-6) capturing inlet buzz are presented.

The body composition, nutritional knowledge, attitudes, behaviors, and future education needs of senior schoolboy rugby players in Ireland.

Science.gov (United States)

Walsh, Michelle; Cartwright, Laura; Corish, Clare; Sugrue, Sheila; Wood-Martin, Ruth

2011-10-01

This study examined the body composition, nutritional knowledge, behaviors, attitudes, and educational needs of senior schoolboy rugby players in Ireland. Participants included 203 male rugby players age 15-18 yr competing at Senior School's Cup level in Leinster, Ireland. Estimation of body composition included measurement of height, weight, and percentage body fat (PBF; using bioelectrical impedance analysis, Tanita BC-418). Nutritional knowledge, behaviors, attitudes, and education needs were assessed by questionnaire. The range of PBF was 5.1-25.3%. Sixty-eight percent of the players in this study had a healthy PBF (10-20%), 32 (22%) were classified as underweight (benefit from appropriate nutritional education.

Performance-based financing as a health system reform: mapping the key dimensions for monitoring and evaluation

Science.gov (United States)

2013-01-01

Background Performance-based financing is increasingly being applied in a variety of contexts, with the expectation that it can improve the performance of health systems. However, while there is a growing literature on implementation issues and effects on outputs, there has been relatively little focus on interactions between PBF and health systems and how these should be studied. This paper aims to contribute to filling that gap by developing a framework for assessing the interactions between PBF and health systems, focusing on low and middle income countries. In doing so, it elaborates a general framework for monitoring and evaluating health system reforms in general. Methods This paper is based on an exploratory literature review and on the work of a group of academics and PBF practitioners. The group developed ideas for the monitoring and evaluation framework through exchange of emails and working documents. Ideas were further refined through discussion at the Health Systems Research symposium in Beijing in October 2012, through comments from members of the online PBF Community of Practice and Beijing participants, and through discussion with PBF experts in Bergen in June 2013. Results The paper starts with a discussion of definitions, to clarify the core concept of PBF and how the different terms are used. It then develops a framework for monitoring its interactions with the health system, structured around five domains of context, the development process, design, implementation and effects. Some of the key questions for monitoring and evaluation are highlighted, and a systematic approach to monitoring effects proposed, structured according to the health system pillars, but also according to inputs, processes and outputs. Conclusions The paper lays out a broad framework within which indicators can be prioritised for monitoring and evaluation of PBF or other health system reforms. It highlights the dynamic linkages between the domains and the different pillars

Performance-based financing as a health system reform: mapping the key dimensions for monitoring and evaluation.

Science.gov (United States)

Witter, Sophie; Toonen, Jurrien; Meessen, Bruno; Kagubare, Jean; Fritsche, György; Vaughan, Kelsey

2013-09-29

Performance-based financing is increasingly being applied in a variety of contexts, with the expectation that it can improve the performance of health systems. However, while there is a growing literature on implementation issues and effects on outputs, there has been relatively little focus on interactions between PBF and health systems and how these should be studied. This paper aims to contribute to filling that gap by developing a framework for assessing the interactions between PBF and health systems, focusing on low and middle income countries. In doing so, it elaborates a general framework for monitoring and evaluating health system reforms in general. This paper is based on an exploratory literature review and on the work of a group of academics and PBF practitioners. The group developed ideas for the monitoring and evaluation framework through exchange of emails and working documents. Ideas were further refined through discussion at the Health Systems Research symposium in Beijing in October 2012, through comments from members of the online PBF Community of Practice and Beijing participants, and through discussion with PBF experts in Bergen in June 2013. The paper starts with a discussion of definitions, to clarify the core concept of PBF and how the different terms are used. It then develops a framework for monitoring its interactions with the health system, structured around five domains of context, the development process, design, implementation and effects. Some of the key questions for monitoring and evaluation are highlighted, and a systematic approach to monitoring effects proposed, structured according to the health system pillars, but also according to inputs, processes and outputs. The paper lays out a broad framework within which indicators can be prioritised for monitoring and evaluation of PBF or other health system reforms. It highlights the dynamic linkages between the domains and the different pillars. All of these are also framed within

Advanced Optical Diagnostic Methods for Describing Fuel Injection and Combustion Flowfield Phenomena

Science.gov (United States)

Locke, Randy J.; Hicks, Yolanda R.; Anderson, Robert C.

2004-01-01

Over the past decade advanced optical diagnostic techniques have evolved and matured to a point where they are now widely applied in the interrogation of high pressure combusting flows. At NASA Glenn Research Center (GRC), imaging techniques have been used successfully in on-going work to develop the next generation of commercial aircraft gas turbine combustors. This work has centered on providing a means by which researchers and designers can obtain direct visual observation and measurements of the fuel injection/mixing/combustion processes and combustor flowfield in two- and three-dimensional views at actual operational conditions. Obtaining a thorough understanding of the chemical and physical processes at the extreme operating conditions of the next generation of combustors is critical to reducing emissions and increasing fuel efficiency. To accomplish this and other tasks, the diagnostic team at GRC has designed and constructed optically accessible, high pressurer high temperature flame tubes and sectar rigs capable of optically probing the 20-60 atm flowfields of these aero-combustors. Among the techniques employed at GRC are planar laser-induced fluorescence (PLIF) for imaging molecular species as well as liquid and gaseous fuel; planar light scattering (PLS) for imaging fuel sprays and droplets; and spontaneous Raman scattering for species and temperature measurement. Using these techniques, optical measurements never before possible have been made in the actual environments of liquid fueled gas turbines. 2-D mapping of such parameters as species (e.g. OH-, NO and kerosene-based jet fuel) distribution, injector spray angle, and fuel/air distribution are just some of the measurements that are now routinely made. Optical imaging has also provided prompt feedback to researchers regarding the effects of changes in the fuel injector configuration on both combustor performance and flowfield character. Several injector design modifications and improvements have

Copper-mediated reductive dechlorination by green rust intercalated with dodecanoate

DEFF Research Database (Denmark)

Huang, Lizhi; Yin, Zhou; Cooper, Nicola G.A.

2018-01-01

A layered FeII-FeIII hydroxide (green rust, GR) was intercalated with dodecanoate (known as GRC12) and then amended with CuII (GRC12(Cu)) before reaction with chloroform (CF), carbon tetrachloride (CT), trichloroethylene (TCE) or tetrachloroethylene (PCE). Reduction of CT by GRC12(Cu) was 37 times...

Pilot-scale comparison of constructed wetlands operated under high hydraulic loading rates and attached biofilm reactors for domestic wastewater treatment

International Nuclear Information System (INIS)

Fountoulakis, M.S.; Terzakis, S.; Chatzinotas, A.; Brix, H.; Kalogerakis, N.; Manios, T.

2009-01-01

Four different pilot-scale treatment units were constructed to compare the feasibility of treating domestic wastewater in the City of Heraklio, Crete, Greece: (a) a free water surface (FWS) wetland system, (b) a horizontal subsurface flow (HSF) wetland system, (c) a rotating biological contactor (RBC), and (d) a packed bed filter (PBF). All units operated in parallel at various hydraulic loading rates (HLR) ranging from 50% to 175% of designed operating HLR. The study was conducted during an 8 month period and showed that COD removal efficiency of HSF was comparable (> 75%) to that of RBC and PBF, whereas that of the FWS system was only 57%. Average nutrient removal efficiencies for FWS, HSF, RBC and PBF were 6%, 21%, 40% and 43%, respectively for total nitrogen and 21%, 39%, 41% and 42%, respectively for total phosphorus. Removals of total coliforms were lowest in FWS and PBF (1.3 log units) and higher in HSF and RBC (2.3 to 2.6 log units). HSF showed slightly lower but comparable effluent quality to that of RBC and PBF systems, but the construction cost and energy requirements for this system are significantly lower. Overall the final decision for the best non-conventional wastewater treatment system depends on the construction and operation cost, the area demand and the required quality of effluent

Similarity in percent body fat between white and Vietnamese women: implication for a universal definition of obesity.

Science.gov (United States)

Ho-Pham, Lan T; Lai, Thai Q; Nguyen, Nguyen D; Barrett-Connor, Elizabeth; Nguyen, Tuan V

2010-06-01

It has been widely assumed that for a given BMI, Asians have higher percent body fat (PBF) than whites, and that the BMI threshold for defining obesity in Asians should be lower than the threshold for whites. This study sought to test this assumption by comparing the PBF between US white and Vietnamese women. The study was designed as a comparative cross-sectional investigation. In the first study, 210 Vietnamese women ages between 50 and 85 were randomly selected from various districts in Ho Chi Minh City (Vietnam). In the second study, 419 women of the same age range were randomly selected from the Rancho Bernardo Study (San Diego, CA). In both studies, lean mass (LM) and fat mass (FM) were measured by dual-energy X-ray absorptiometry (DXA) (QDR 4500; Hologic). PBF was derived as FM over body weight. Compared with Vietnamese women, white women had much more FM (24.8 +/- 8.1 kg vs. 18.8 +/- 4.9 kg; P or=30, 19% of US white women and 5% of Vietnamese women were classified as obese. Approximately 54% of US white women and 53% of Vietnamese women had their PBF >35% (P = 0.80). Although white women had greater BMI, body weight, and FM than Vietnamese women, their PBF was virtually identical. Further research is required to derive a more appropriate BMI threshold for defining obesity for Asian women.

Getting Your Ducks in a Row: IT Governance, Risk, and Compliance Programs in Higher Education

Science.gov (United States)

Bichsel, Jacqueline; Feehan, Patrick

2014-01-01

Higher education IT governance, risk, and compliance (GRC) programs are in the development stage. Few institutions have all three programs in place, and many institutions are unclear where they should start when instituting or maturing their IT GRC programs. In addition, they are often uncertain as to whether GRC programs should be developed in…

Efectos combinados de la ampliación de la atención primaria de salud y de las transferencias condicionadas de dinero en efectivo sobre la mortalidad infantil en Brasil, 1998–2010*

Science.gov (United States)

Guanais, Frederico C.

2015-01-01

Objetivos. Examiné los efectos combinados del acceso a la atención primaria mediante el Programa de Salud Familiar (PSF) y las transferencias condicionadas de dinero en efectivo del Programa Bolsa Familia (PBF) sobre la mortalidad infantil posneonatal (MIPN) en Brasil. Métodos. Empleé un análisis ecológico longitudinal usando datos en panel de 4 583 municipios brasileños de 1998 al 2010, con 54 253 observaciones en total. Estimé modelos de regresión de efectos fijos por mínimos cuadrados ordinarios, con la tasa de MIPN como la variable dependiente y el PSF, el PBF y sus interacciones como las principales variables independientes de interés. Resultados. La asociación de una mayor cobertura del PSF con una menor tasa de MIPN se volvió más fuerte conforme aumentaba la cobertura del PBF. En los promedios de todas las demás variables, cuando la cobertura de PBF era 25%, la MIPN predicha fue 5,24 (intervalo de confianza [IC] de 95% = 4,95, 5,53) para una cobertura del PSF de 0%, y de 3,54 (IC de 95% = 2,77, 4,31) para una cobertura del PSF de 100%. Cuando la cobertura del PBF era de 60%, la MIPN predicha fue 4,65 (IC de 95% = 4,36, 4,94) para una cobertura del PSF de 0%, y de 1,38 (IC de 95% = 0,88, 1,89) para una cobertura del PSF de 100%. Conclusiones. El efecto del PSF depende de la ampliación del PBF. Para las poblaciones empobrecidas y subatendidas, la combinación de intervenciones tanto del lado de la oferta como del lado de la demanda podría ser necesaria para mejorar los resultados en salud.

INEL BNCT Program: Volume 5, No. 9. Bulletin, September 1991

Energy Technology Data Exchange (ETDEWEB)

Ackermann, A.L. [ed.

1991-12-31

This Bulletin presents a summary of accomplishments and highlights of the Idaho National Engineering Laboratory`s (INEL) Boron Neutron Capture Therapy (BNCT) Program for September 1991. This bulletin includes information on the brain tumor and melanoma research programs, Power Burst Facility (PBF) technical support and modifications, PBF operations, and updates to the animal data charts.

INEL BNCT Program

International Nuclear Information System (INIS)

Ackermann, A.L.; Dorn, R.V. III.

1991-03-01

This Bulletin presents a summary of accomplishments and highlights in the Idaho National Engineering Laboratory (INEL) Boron Neutron Capture Therapy (BNCT) Program for March 1991. This bulletin includes information on the brain tumor and melanoma research programs, Power Burst Facility (PBF) technical support and modifications, PBF operations, a milestone summary, and animal data charts

Geothermal Information Dissemination and Outreach

Energy Technology Data Exchange (ETDEWEB)

Clutter, Ted J. [Geothermal Resources Council (United States)

2005-02-18

Project Purpose. To enhance technological and topical information transfer in support of industry and government efforts to increase geothermal energy use in the United States (power production, direct use, and geothermal groundsource heat pumps). Project Work. GRC 2003 Annual Meeting. The GRC convened the meeting on Oct. 12-15, 2003, at Morelia's Centro de Convenciones y ExpoCentro in Mexico under the theme, International Collaboration for Geothermal Energy in the Americas. The event was also sponsored by the Comision Federal de Electricidad. ~600 participants from more than 20 countries attended the event. The GRC convened a Development of Geothermal Projects Workshop and Geothermal Exploration Techniques Workshop. GRC Field Trips included Los Azufres and Paricutin Volcano on Oct. 11. The Geothermal Energy Association (Washington, DC) staged its Geothermal Energy Trade Show. The Annual Meeting Opening Session was convened on Oct. 13, and included the governor of Michoacan, the Mexico Assistant Secretary of Energy, CFE Geothermal Division Director, DOE Geothermal Program Manager, and private sector representatives. The 2003 Annual Meeting attracted 160 papers for oral and poster presentations. GRC 2004. Under the theme, Geothermal - The Reliable Renewable, the GRC 2004 Annual Meeting convened on Aug. 29-Sept. 1, 2004, at the Hyatt Grand Champions Resort at Indian Wells, CA. Estimated total attendance (including Trade Show personnel, guests and accompanying persons) was ~700. The event included a workshop, Geothermal Production Well Pump Installation, Operation and Maintenance. Field trips went to Coso/Mammoth and Imperial Valley/Salton Sea geothermal fields. The event Opening Session featured speakers from the U.S. Department of Energy, U.S. Department of the Interior, and the private sector. The Geothermal Energy Association staged its Geothermal Energy Trade Show. The Geothermal Education Office staged its Geothermal Energy Workshop. Several local radio and

Investigation of plasma–surface interaction at plasma beam facilities

Energy Technology Data Exchange (ETDEWEB)

Kurnaev, V., E-mail: kurnaev@plasma.mephi.ru [National Research Nuclear University MEPhI (Moscow Engineering Physics Institute), Kashirskoe sh. 31, 115409 Moscow (Russian Federation); Vizgalov, I.; Gutorov, K. [National Research Nuclear University MEPhI (Moscow Engineering Physics Institute), Kashirskoe sh. 31, 115409 Moscow (Russian Federation); Tulenbergenov, T.; Sokolov, I.; Kolodeshnikov, A.; Ignashev, V.; Zuev, V.; Bogomolova, I. [Institute of Atomic Energy, National Nuclear Center the Republic of Kazakhstan, Street Krasnoarmejsky, 10, 071100 Kurchatov (Kazakhstan); Klimov, N. [SRC RF TRINITI, ul. Pushkovykh, vladenie 12, Troitsk, 142190 Moscow (Russian Federation)

2015-08-15

The new Plasma Beam Facility (PBF) has been put into operation for assistance in testing of plasma faced components at Material Science Kazakhstan Tokamak (KTM). PBF includes a powerful electron gun (up to 30 kV, 1 A) and a high vacuum chamber with longitudinal magnetic field coils (up to 0.2 T). The regime of high vacuum electron beam transportation is used for thermal tests with power density at the target surface up to 10 GW/m{sup 2}. The beam plasma discharge (BPD) regime with a gas-puff is used for generation of intensive ion fluxes up to 3 ⋅ 10{sup 22} m{sup −2} s{sup −1}. Initial tests of the KTM PBF’s capabilities were carried out: various discharge regimes, carbon deposits cleaning, simultaneous thermal and ion impacts on radiation cooled refractory targets. With a water-cooled target the KTM PBF could be used for high heat flux tests of materials (validated by the experiment with W mock-up at the PR-2 PBF)

Power Burst Facility Severe Fuel Damage test series

International Nuclear Information System (INIS)

Buescher, B.J.; Osetek, D.J.; Ploger, S.A.

1982-01-01

The Severe Fuel Damage (SFD) tests planned for the Power Burst Facility (PBF) are described. Bundles containing 32 zircaloy-clad, PWR-type fuel rods will be subjected to severe overheating transients in a high-pressure, superheated-steam environment. Cladding temperatures are expected to reach 2400 0 K, resulting in cladding ballooning and rupture, severe cladding oxidation, cladding melting, fuel dissolution, fuel rod fragmentation, and possibly, rubble bed formation. An experiment effluent collection system is being installed and the PBF fission product monitoring system is being upgraded to meet the special requirements of the SFD tests. Scoping calculations were performed to evaluate performance of the SFD test design and to establish operational requirements for the PBF loop

INEL BNCT Program: Volume 5, No. 9

Energy Technology Data Exchange (ETDEWEB)

Ackermann, A.L. (ed.)

1991-01-01

This Bulletin presents a summary of accomplishments and highlights of the Idaho National Engineering Laboratory's (INEL) Boron Neutron Capture Therapy (BNCT) Program for September 1991. This bulletin includes information on the brain tumor and melanoma research programs, Power Burst Facility (PBF) technical support and modifications, PBF operations, and updates to the animal data charts.

INEL BNCT Program

Energy Technology Data Exchange (ETDEWEB)

Ackermann, A.L. (ed.)

1991-08-01

This Bulletin presents a summary of accomplishments and highlights in the Idaho National Engineering Laboratory's (INEL) Boron Neutron Capture Therapy (BNCT) Program for August 1991. This bulletin includes information on the brain tumor and melanoma research programs, Power Burst Facility (PBF) technical support and modifications, PBF operations, and updates to the animal data charts.

Comparison of gas clearance and radioactive microspheres for pancreatic blood flow measurement

International Nuclear Information System (INIS)

DeMar, A.R.; Graham, L.S.; Lake, R.; Fink, A.S.

1989-01-01

Measurement of pancreatic blood flow (PBF) is technically demanding. Although radiolabeled microspheres are considered the gold standard for PBF assessment, they have practical limitations. In the current study, H 2 and xenon-133 gas clearance techniques were adapted to PBF measurement and compared to radiolabeled microsphere techniques. Simultaneous measurements of PBF were made using either hydrogen or xenon gas washout and radiolabeled microspheres. Measurements were made under basal, vasoconstricted (vasopressin 2U i.v. or nicotine 4 micrograms/kg/h) and stimulated (secretin 125 ng/kg/h or 2 U/kg i.v.) conditions (random order). Mean PBF was 26.9 +/- 5.3, 50.5 +/- 2.3 and 27.6 +/- 5.2 ml/min/100 g basally, 36.9 +/- 8.0, 90.1 +/- 18.9, and 81.7 +/- 14.5 ml/min/100 g in the stimulated state, and 24.2 +/- 7.8, 25.0 +/- 3.5, and 14.9 +/- 7.5 ml/min/100 g in the vasoconstricted state for hydrogen gas clearance, xenon gas clearance, and radiolabeled microspheres, respectively. The H 2 clearance technique resulted in tissue trauma, was complicated by frequent electrode displacement, and correlated poorly (r2 = 0.36, p greater than 0.05) with microsphere values. In contrast, xenon clearance measurement had no apparent effect on the pancreas and correlated well (r2 = 0.83, p less than 0.01) with microsphere data. We conclude that xenon clearance offers an attractive, validated alternative to radiolabeled microspheres for measuring pancreatic blood flow

The effect of intraosseous local anesthesia of 4% articaine with 1:100,000 epinephrine on pulpal blood flow and pulpal anesthesia of mandibular molars and canines.

Science.gov (United States)

Vongsavan, Kadkao; Samdrup, Tshering; Kijsamanmith, Kanittha; Rirattanapong, Praphasri; Vongsavan, Noppakun

2018-05-10

The aim of this study was to determine the effect of intraosseous (IO) anesthesia with 4% articaine and 1:100,000 epinephrine on pulpal blood flow (PBF) and pulpal anesthesia of mandibular first molars and canines in human subjects. Ten healthy volunteers with intact mandibular first molar and canine were given an osteocentral technique of IO injection using the Quick Sleeper 5 system and 4% articaine with 1:100,000 epinephrine at distal site of mandibular first molar. The PBF was monitored by a laser Doppler flowmeter (LDF). Pulpal anesthesia was assessed with an electric pulp tester (EPT). IO injection caused a decrease in PBF in molars from 6.31 ± 3.85 perfusion units (P.U.) before injection to 2.51 ± 2.53 P.U. 1 min after injection (P anesthesia in the molars, the mean onset was 2.40 ± 0.84 min and the mean duration was 38 ± 16.19 min. In the canines, there was a decrease in the sensitivity to EPT but complete pulpal anesthesia was not achieved. IO injection distal to mandibular first molar caused a decrease in PBF and successful pulpal anesthesia in first molar, but not in canine. Both PBF and EPT readings returned to normal, suggesting that pulpal ischemia may not occur. IO anesthesia is safe to use as a primary technique in teeth with normal pulp.

A Novel Antagonist of the Immune Checkpoint Protein Adenosine A2a Receptor Restores Tumor-Infiltrating Lymphocyte Activity in the Context of the Tumor Microenvironment

Directory of Open Access Journals (Sweden)

Melanie Mediavilla-Varela

2017-07-01

Full Text Available BACKGROUND: Therapeutic strategies targeting immune checkpoint proteins have led to significant responses in patients with various tumor types. The success of these studies has led to the development of various antibodies/inhibitors for the different checkpoint proteins involved in immune evasion of the tumor. Adenosine present in high concentrations in the tumor microenvironment activates the immune checkpoint adenosine A2a receptor (A2aR, leading to the suppression of antitumor responses. Inhibition of this checkpoint has the potential to enhance antitumor T-cell responsiveness. METHODS: We developed a novel A2aR antagonist (PBF-509 and tested its antitumor response in vitro, in a mouse model, and in non-small cell lung cancer patient samples. RESULTS: Our studies showed that PBF-509 is highly specific to the A2aR as well as inhibitory of A2aR function in an in vitro model. In a mouse model, we found that lung metastasis was decreased after treatment with PBF-509 compared with its control. Furthermore, freshly resected tumor-infiltrating lymphocytes from lung cancer patients showed increased A2aR expression in CD4+ cells and variable expression in CD8+ cells. Ex vivo studies showed an increased responsiveness of human tumor-infiltrating lymphocytes when PBF-509 was combined with anti-PD-1 or anti-PD-L1. CONCLUSIONS: Our studies demonstrate that inhibition of the A2aR using the novel inhibitor PBF-509 could lead to novel immunotherapeutic strategies in non-small cell lung cancer.

Discovery of the First Germline-Restricted Gene by Subtractive Transcriptomic Analysis in the Zebra Finch, Taeniopygia guttata.

Science.gov (United States)

Biederman, Michelle K; Nelson, Megan M; Asalone, Kathryn C; Pedersen, Alyssa L; Saldanha, Colin J; Bracht, John R

2018-05-21

Developmentally programmed genome rearrangements are rare in vertebrates, but have been reported in scattered lineages including the bandicoot, hagfish, lamprey, and zebra finch (Taeniopygia guttata) [1]. In the finch, a well-studied animal model for neuroendocrinology and vocal learning [2], one such programmed genome rearrangement involves a germline-restricted chromosome, or GRC, which is found in germlines of both sexes but eliminated from mature sperm [3, 4]. Transmitted only through the oocyte, it displays uniparental female-driven inheritance, and early in embryonic development is apparently eliminated from all somatic tissue in both sexes [3, 4]. The GRC comprises the longest finch chromosome at over 120 million base pairs [3], and previously the only known GRC-derived sequence was repetitive and non-coding [5]. Because the zebra finch genome project was sourced from male muscle (somatic) tissue [6], the remaining genomic sequence and protein-coding content of the GRC remain unknown. Here we report the first protein-coding gene from the GRC: a member of the α-soluble N-ethylmaleimide sensitive fusion protein (NSF) attachment protein (α-SNAP) family hitherto missing from zebra finch gene annotations. In addition to the GRC-encoded α-SNAP, we find an additional paralogous α-SNAP residing in the somatic genome (a somatolog)-making the zebra finch the first example in which α-SNAP is not a single-copy gene. We show divergent, sex-biased expression for the paralogs and also that positive selection is detectable across the bird α-SNAP lineage, including the GRC-encoded α-SNAP. This study presents the identification and evolutionary characterization of the first protein-coding GRC gene in any organism. Copyright © 2018 Elsevier Ltd. All rights reserved.

World Health Organization guideline development: an evaluation.

Directory of Open Access Journals (Sweden)

David Sinclair

Full Text Available BACKGROUND: Research in 2007 showed that World Health Organization (WHO recommendations were largely based on expert opinion, rarely used systematic evidence-based methods, and did not follow the organization's own "Guidelines for Guidelines". In response, the WHO established a "Guidelines Review Committee" (GRC to implement and oversee internationally recognized standards. We examined the impact of these changes on WHO guideline documents and explored senior staff's perceptions of the new procedures. METHODS AND FINDINGS: We used the AGREE II guideline appraisal tool to appraise ten GRC-approved guidelines from nine WHO departments, and ten pre-GRC guidelines matched by department and topic. We interviewed 20 senior staff across 16 departments and analyzed the transcripts using the framework approach. Average AGREE II scores for GRC-approved guidelines were higher across all six AGREE domains compared with pre-GRC guidelines. The biggest changes were noted for "Rigour of Development" (up 37.6%, from 30.7% to 68.3% and "Editorial Independence" (up 52.7%, from 20.9% to 73.6%. Four main themes emerged from the interviews: (1 high standards were widely recognized as essential for WHO credibility, particularly with regard to conflicts of interest; (2 views were mixed on whether WHO needed a single quality assurance mechanism, with some departments purposefully bypassing the procedures; (3 staff expressed some uncertainties in applying the GRADE approach, with departmental staff concentrating on technicalities while the GRC remained concerned the underlying principles were not fully institutionalized; (4 the capacity to implement the new standards varied widely, with many departments looking to an overstretched GRC for technical support. CONCLUSIONS: Since 2007, WHO guideline development methods have become more systematic and transparent. However, some departments are bypassing the procedures, and as yet neither the GRC, nor the quality assurance

Demonstration of array eddy current technology for real-time monitoring of laser powder bed fusion additive manufacturing process

Science.gov (United States)

Todorov, Evgueni; Boulware, Paul; Gaah, Kingsley

2018-03-01

Nondestructive evaluation (NDE) at various fabrication stages is required to assure quality of feedstock and solid builds. Industry efforts are shifting towards solutions that can provide real-time monitoring of additive manufacturing (AM) fabrication process layer-by-layer while the component is being built to reduce or eliminate dependence on post-process inspection. Array eddy current (AEC), electromagnetic NDE technique was developed and implemented to directly scan the component without physical contact with the powder and fused layer surfaces at elevated temperatures inside a LPBF chamber. The technique can detect discontinuities, surface irregularities, and undesirable metallurgical phase transformations in magnetic and nonmagnetic conductive materials used for laser fusion. The AEC hardware and software were integrated with the L-PBF test bed. Two layer-by-layer tests of Inconel 625 coupons with AM built discontinuities and lack of fusion were conducted inside the L-PBF chamber. The AEC technology demonstrated excellent sensitivity to seeded, natural surface, and near-surface-embedded discontinuities, while also detecting surface topography. The data was acquired and imaged in a layer-by-layer sequence demonstrating the real-time monitoring capabilities of this new technology.

High Mobility, High Life Wheels for Mars

Data.gov (United States)

National Aeronautics and Space Administration — GRC will build Mars spring tires based on JPL requirements. GRC will evaluate tractive performance. JPL will conduct life cycle testing and load analysis.

Development and Testing of the Glenn Research Center Visitor's Center Grid-Tied Photovoltaic Power System

Science.gov (United States)

Eichenberg, Dennis J.

2009-01-01

The NASA Glenn Research Center (GRC) has developed, installed, and tested a 12 kW DC grid-tied photovoltaic (PV) power system at the GRC Visitor s Center. This system utilizes a unique ballast type roof mount for installing the photovoltaic panels on the roof of the Visitor s Center with no alterations or penetrations to the roof. The PV system has generated in excess of 15000 kWh since operation commenced in August 2008. The PV system is providing power to the GRC grid for use by all. Operation of the GRC Visitor s Center PV system has been completely trouble free. A grid-tied PV power system is connected directly to the utility distribution grid. Facility power can be obtained from the utility system as normal. The PV system is synchronized with the utility system to provide power for the facility, and excess power is provided to the utility. The project transfers space technology to terrestrial use via nontraditional partners. GRC personnel glean valuable experience with PV power systems that are directly applicable to various space power systems, and provides valuable space program test data. PV power systems help to reduce harmful emissions and reduce the Nation s dependence on fossil fuels. Power generated by the PV system reduces the GRC utility demand, and the surplus power aids the community. Present global energy concerns reinforce the need for the development of alternative energy systems. Modern PV panels are readily available, reliable, efficient, and economical with a life expectancy of at least 25 years. Modern electronics has been the enabling technology behind grid-tied power systems, making them safe, reliable, efficient, and economical with a life expectancy of at least 25 years. Based upon the success of the GRC Visitor s Center PV system, additional PV power system expansion at GRC is under consideration. The GRC Visitor s Center grid-tied PV power system was successfully designed and developed which served to validate the basic principles

Design of a Glenn Research Center Solar Field Grid-Tied Photovoltaic Power System

Science.gov (United States)

Eichenberg, Dennis J.

2009-01-01

The NASA Glenn Research Center (GRC) designed, developed, and installed, a 37.5 kW DC photovoltaic (PV) Solar Field in the GRC West Area in the 1970s for the purpose of testing PV panels for various space and terrestrial applications. The PV panels are arranged to provide a nominal 120 VDC. The GRC Solar Field has been extremely successful in meeting its mission. The PV panels and the supporting electrical systems are all near their end of life. GRC has designed a 72 kW DC grid-tied PV power system to replace the existing GRC West Area Solar Field. The 72 kW DC grid-tied PV power system will provide DC solar power for GRC PV testing applications, and provide AC facility power for all times that research power is not required. A grid-tied system is connected directly to the utility distribution grid. Facility power can be obtained from the utility system as normal. The PV system is synchronized with the utility system to provide power for the facility, and excess power is provided to the utility for use by all. The project transfers space technology to terrestrial use via nontraditional partners. GRC personnel glean valuable experience with PV power systems that are directly applicable to various space power systems, and provide valuable space program test data. PV power systems help to reduce harmful emissions and reduce the Nation s dependence on fossil fuels. Power generated by the PV system reduces the GRC utility demand, and the surplus power aids the community. Present global energy concerns reinforce the need for the development of alternative energy systems. Modern PV panels are readily available, reliable, efficient, and economical with a life expectancy of at least 25 years. Modern electronics has been the enabling technology behind grid-tied power systems, making them safe, reliable, efficient, and economical with a life expectancy of at least 25 years. The report concludes that the GRC West Area grid-tied PV power system design is viable for a reliable

Performance-based financing to increase utilization of maternal health services: Evidence from Burkina Faso

Directory of Open Access Journals (Sweden)

Maria Steenland

2017-12-01

Full Text Available Performance-based financing (PBF programs are increasingly implemented in low and middle-income countries to improve health service quality and utilization. In April 2011, a PBF pilot program was launched in Boulsa, Leo and Titao districts in Burkina Faso with the objective of increasing the provision and quality of maternal health services. We evaluate the impact of this program using facility-level administrative data from the national health management information system (HMIS. Primary outcomes were the number of antenatal care visits, the proportion of antenatal care visits that occurred during the first trimester of pregnancy, the number of institutional deliveries and the number of postnatal care visits. To assess program impact we use a difference-in-differences approach, comparing changes in health service provision post-introduction with changes in matched comparison areas. All models were estimated using ordinary least squares (OLS regression models with standard errors clustered at the facility level. On average, PBF facilities had 2.3 more antenatal care visits (95% CI [0.446–4.225], 2.1 more deliveries (95% CI [0.034–4.069] and 9.5 more postnatal care visits (95% CI [6.099, 12.903] each month after the introduction of PBF. Compared to the service provision levels prior to the interventions, this implies a relative increase of 27.7 percent for ANC, of 9.2 percent for deliveries, and of 118.7 percent for postnatal care. Given the positive results observed during the pre-pilot period and the limited resources available in the health sector, the PBF program in Burkina Faso may be a low-cost, high impact intervention to improve maternal and child health.

A study on the implementation fidelity of the performance-based financing policy in Burkina Faso after 12 months.

Science.gov (United States)

Bodson, Oriane; Barro, Ahmed; Turcotte-Tremblay, Anne-Marie; Zanté, Nestor; Somé, Paul-André; Ridde, Valéry

2018-01-01

Performance-based financing (PBF) in the health sector has recently gained momentum in low- and middle-income countries (LMICs) as one of the ways forward for achieving Universal Health Coverage. The major principle underlying PBF is that health centers are remunerated based on the quantity and quality of services they provide. PBF has been operating in Burkina Faso since 2011, and as a pilot project since 2014 in 15 health districts randomly assigned into four different models, before an eventual scale-up. Despite the need for expeditious documentation of the impact of PBF, caution is advised to avoid adopting hasty conclusions. Above all, it is crucial to understand why and how an impact is produced or not. Our implementation fidelity study approached this inquiry by comparing, after 12 months of operation, the activities implemented against what was planned initially and will make it possible later to establish links with the policy's impacts. Our study compared, in 21 health centers from three health districts, the implementation of activities that were core to the process in terms of content, coverage, and temporality. Data were collected through document analysis, as well as from individual interviews and focus groups with key informants. In the first year of implementation, solid foundations were put in place for the intervention. Even so, implementation deficiencies and delays were observed with respect to certain performance auditing procedures, as well as in payments of PBF subsidies, which compromised the incentive-based rationale to some extent. Over next months, efforts should be made to adjust the intervention more closely to context and to the original planning.

Blood-flow change and recovery of sensibility in the maxillary dental pulp during and after maxillary distraction: a pilot study.

Science.gov (United States)

Harada, Kiyoshi; Sato, Masaru; Omura, Ken

2004-11-01

To examine the change in blood flow and recovery of sensibility in the maxillary dental pulp during and after maxillary distraction. The subjects included 5 patients undergoing high Le Fort I osteotomy and maxillary distraction (D-group) and a reference group of 14 patients who underwent a common single-segment Le Fort I osteotomy, 1-stage maxillary advancement, and mandibular setback surgery (C-group). Eleven (D-group) and 54 (C-group) maxillary incisors were assessed preoperatively and at 1-7 days, 14 days, and 3 months postoperatively. Pulpal blood flow (PBF) was measured by laser Doppler flowmetry, and pulpal sensibility (PS) was investigated by electrodiagnostics. From postoperative days 1 to 5 (the latency period), the PBF tended to be higher in the D-group than in the C-group. From day 6 to 3 months postoperatively (during and after maxillary distraction), the PBF values of the 2 groups were similar. The PS remained negative up to 14 days postoperatively in both groups. However, at 3 months after the operation, a higher proportion (90.9%) of teeth in the D-group was positive for PS. These results suggest that maxillary distraction is a favorable technique for maintenance of PBF and recovery of PS in the maxillary teeth after surgery.

Activity coefficients at infinite dilution of organic solutes in the ionic liquid trihexyl(tetradecyl)phosphonium tetrafluoroborate using gas-liquid chromatography at T = (313.15, 333.15, 353.15, and 373.15) K

International Nuclear Information System (INIS)

Tumba, Kaniki; Reddy, Prashant; Naidoo, Paramespri; Ramjugernath, Deresh

2011-01-01

Research highlights: → Activity coefficients at infinite dilution in the ionic liquid [3C 6 C 14 P][BF 4 ]. → Twenty-seven solutes investigated at T = (313.15, 333.15, 353.15, and 373.15) K. → [3C 6 C 14 P][BF 4 ] shows promise for the separation of aromatic and alcohol mixtures. - Abstract: Activity coefficients at infinite dilution have been measured by gas-liquid chromatography for 27 organic solutes (n-alkanes, 1-alkenes, 1-alkynes, cycloalkanes, aromatics, alcohols, and ketones) in the ionic liquid trihexyl(tetradecyl)phosphonium tetrafluoroborate [3C 6 C 14 P][BF 4 ]. The measurements were carried out at four different temperatures viz.T = (313.15, 333.15, 353.15, and 373.15) K. From the experimental data, partial molar excess enthalpy values at infinite dilution were calculated for the experimental temperature range. The selectivity values for the separation of n-hexane/benzene, cyclohexane/benzene, and methanol/benzene mixtures were determined from the experimental infinite dilution activity coefficient values. These values were compared to those available in the literature for other ionic liquids and commercial solvents, so as to assess the feasibility of employing [3C 6 C 14 P][BF 4 ] in solvent-enhanced industrial separations.

A general strategy toward graphitized carbon coating on iron oxides as advanced anodes for lithium-ion batteries.

Science.gov (United States)

Ding, Chunyan; Zhou, Weiwei; Wang, Bin; Li, Xin; Wang, Dong; Zhang, Yong; Wen, Guangwu

2017-08-25

Integration of carbon materials with benign iron oxides is blazing a trail in constructing high-performance anodes for lithium-ion batteries (LIBs). In this paper, a unique general, simple, and controllable strategy is developed toward in situ uniform coating of iron oxide nanostructures with graphitized carbon (GrC) layers. The basic synthetic procedure only involves a simple dip-coating process for the loading of Ni-containing seeds and a subsequent Ni-catalyzed chemical vapor deposition (CVD) process for the growth of GrC layers. More importantly, the CVD treatment is conducted at a quite low temperature (450 °C) and with extremely facile liquid carbon sources consisting of ethylene glycol (EG) and ethanol (EA). The GrC content of the resulting hybrids can be controllably regulated by altering the amount of carbon sources. The electrochemical results reveal remarkable performance enhancements of iron oxide@GrC hybrids compared with pristine iron oxides in terms of high specific capacity, excellent rate and cycling performance. This can be attributed to the network-like GrC coating, which can improve not only the electronic conductivity but also the structural integrity of iron oxides. Moreover, the lithium storage performance of samples with different GrC contents is measured, manifesting that optimized electrochemical property can be achieved with appropriate carbon content. Additionally, the superiority of GrC coating is demonstrated by the advanced performance of iron oxide@GrC compared with its corresponding counterpart, i.e., iron oxides with amorphous carbon (AmC) coating. All these results indicate the as-proposed protocol of GrC coating may pave the way for iron oxides to be promising anodes for LIBs.

Programa Bolsa Família e segurança alimentar e nutricional no Brasil: revisão crítica da literatura The Bolsa Família cash transfer program and food and nutrition security in Brazil: a critical review of the literature

Directory of Open Access Journals (Sweden)

Rosângela Minardi Mitre Cotta

2013-01-01

Full Text Available OBJETIVO: Revisar criticamente os estudos que avaliaram os impactos do Programa Bolsa Família (PBF na promoção da segurança alimentar e nutricional no Brasil. MÉTODOS: Foram consultadas as bases de dados Biblioteca Cochrane, LILACS, Medline e SciELO, bem como os portais de organizações públicas. Foram selecionados os estudos que utilizaram dados primários e excluídos estudos baseados em dados secundários, artigos de revisão, estudos que não permitiram estabelecer uma associação entre PBF e segurança alimentar e nutricional, bem como os estudos que avaliaram a segurança do alimento no que se refere apenas à qualidade sanitária. RESULTADOS Foram selecionados 10 estudos, dos quais cinco concluíram que o PBF teve um impacto positivo na segurança alimentar e nutricional das famílias beneficiárias. Entretanto, três estudos constataram um aumento do consumo de alimentos de maior densidade calórica e baixo valor nutritivo. Essa mudança no hábito alimentar é um fator de risco para o desenvolvimento do sobrepeso, obesidade e das doenças crônicas não transmissíveis. CONCLUSÕES: A garantia de segurança alimentar e nutricional exige programas que contemplem tanto o combate à desnutrição quanto ao sobrepeso e à obesidade. Programas de distribuição de renda, como o PBF, podem contribuir mais efetivamente para o bem-estar nutricional dos beneficiários quando combinados com outros tipos de intervenções, como ações de promoção de alimentação saudável.OBJECTIVE: To critically review studies evaluating the impact of Bolsa Família (PBF, a federal cash transfer program, for food and nutrition security in Brazil. METHODS: The Cochrane Library, LILACS, Medline and SciELO databases were searched, as well as public organization websites. All studies based on primary data were selected. The following were excluded: studies using secondary data, review articles, studies that did now allow the establishment of associations

Tracking Global Fund HIV/AIDS resources used for sexual and reproductive health service integration: case study from Ethiopia.

Science.gov (United States)

Mookherji, Sangeeta; Ski, Samantha; Huntington, Dale

2015-05-27

The Global Fund to Fight AIDS, Tuberculosis & Malaria (GF) strives for high value for money, encouraging countries to integrate synergistic services and systems strengthening to maximize investments. The GF needs to show how, and how much, its grants support more than just HIV/AIDS, TB and malaria. Sexual and Reproductive Health (SRH) has been part of HIV/AIDS grants since 2007. Previous studies showed the GF PBF system does not allow resource tracking for SRH integration within HIV/AIDS grants. We present findings from a resource tracking case study using primary data collected at country level. Ethiopia was the study site. We reviewed data from four HIV/AIDS grants from January 2009-June 2011 and categorized SDAs and activities as directly, indirectly, or not related to SRH integration. Data included: GF PBF data; financial, performance, in-depth interview and facility observation data from Ethiopia. All HIV/AIDS grants in Ethiopia support SRH integration activities (12-100%). Using activities within SDAs, expenditures directly supporting SRH integration increased from 25% to 66% for the largest HIV/AIDS grant, and from 21% to 34% for the smaller PMTCT-focused grant. Using SDAs to categorize expenditures underestimated direct investments in SRH integration; activity-based categorization is more accurate. The important finding is that primary data collection could not resolve the limitations in using GF GPR data for resource tracking. The remedy is to require existing activity-based budgets and expenditure reports as part of PBF reporting requirements, and make them available in the grant portfolio database. The GF should do this quickly, as it is a serious shortfall in the GF guiding principle of transparency. Showing high value for money is important for maximizing impact and replenishments. The Global Fund should routinely track HIV/AIDs grant expenditures to disease control, service integration, and overall health systems strengthening. The current PBF system

Locust adipokinetic hormone mobilizes diacylglycerols selectively

Czech Academy of Sciences Publication Activity Database

Tomčala, Aleš; Bártů, Iva; Šimek, Petr; Kodrík, Dalibor

2010-01-01

Roč. 156, č. 1 (2010), s. 26-32 ISSN 1096-4959 R&D Projects: GA ČR GA522/07/0788; GA ČR GAP501/10/1215 Grant - others:University of South Bohemia(CZ) 58/2006/P-BF; University of South Bohemia(CZ) 56/2006/P-BF Institutional research plan: CEZ:AV0Z50070508; CEZ:AV0Z40550506 Keywords : AKH * lipid * diacylglycerol Subject RIV: ED - Physiology Impact factor: 1.989, year: 2010

Are health workers motivated by income? Job motivation of Cambodian primary health workers implementing performance-based financing.

Science.gov (United States)

Khim, Keovathanak

2016-01-01

Financial incentives are widely used in performance-based financing (PBF) schemes, but their contribution to health workers' incomes and job motivation is poorly understood. Cambodia undertook health sector reform from the middle of 2009 and PBF was employed as a part of the reform process. This study examines job motivation for primary health workers (PHWs) under PBF reform in Cambodia and assesses the relationship between job motivation and income. A cross-sectional self-administered survey was conducted on 266 PHWs, from 54 health centers in the 15 districts involved in the reform. The health workers were asked to report all sources of income from public sector jobs and provide answers to 20 items related to job motivation. Factor analysis was conducted to identify the latent variables of job motivation. Factors associated with motivation were identified through multivariable regression. PHWs reported multiple sources of income and an average total income of US$190 per month. Financial incentives under the PBF scheme account for 42% of the average total income. PHWs had an index motivation score of 4.9 (on a scale from one to six), suggesting they had generally high job motivation that was related to a sense of community service, respect, and job benefits. Regression analysis indicated that income and the perception of a fair distribution of incentives were both statistically significant in association with higher job motivation scores. Financial incentives used in the reform formed a significant part of health workers' income and influenced their job motivation. Improving job motivation requires fixing payment mechanisms and increasing the size of incentives. PBF is more likely to succeed when income, training needs, and the desire for a sense of community service are addressed and institutionalized within the health system.

Impact of implementing performance-based financing on childhood malnutrition in Rwanda.

Science.gov (United States)

Binagwaho, Agnes; Condo, Jeanine; Wagner, Claire; Ngabo, Fidele; Karema, Corine; Kanters, Steve; Forrest, Jamie I; Bizimana, Jean de Dieu

2014-11-04

Malnutrition remains a serious concern in Rwanda, particularly among children under-5 years. Performance-based financing (PBF), an innovative health systems financing strategy, has been implemented at the national level since 2008. This study aimed to assess the impact of PBF and other factors associated with the prevalence of three classifications of malnutrition (stunting, wasting and underweight) in children under-5 years in Rwanda. The study is a cross-sectional study comprising of 713 children under five years old from 557 households, whose anthropometric measurements (height, weight and age) had been obtained as part of the 2008 Rwanda General Health and HIV household survey. Z-scores for height-for-age, weight-for-age, weight-for-height, and body mass index-for-age were analyzed according to the World Health Organization 2006 Child Growth Standards. Random intercept logistic regression models were used to regress each anthropometric measure (WAZ, HAZ and WHZ) against child, maternal and household characteristics. Child participants ranged in age from 0 to 60 months, 20.2% of children were under 12 months and 5.1% were HIV positive. The prevalence of wasting was 8.8%; of stunting was 58.4%; and of underweight status was 20.7%. Maternal emotional and social wellbeing was protective of wasting in children under-5 years of age. Living in districts implementing PBF was protective of wasting (Adjusted Odds Ratio: 0.43; 95% confidence interval: 0.19-0.97). Living in a district with PBF was not found to be associated with either stunting or underweight status among children under-5. PBF may have a protective association with particular forms of malnutrition among children under-5 years in Rwanda. These findings warrant further investigation in relation to the impact of implementing innovative financing schemes on health outcomes.

Setting performance-based financing in the health sector agenda: a case study in Cameroon.

Science.gov (United States)

Sieleunou, Isidore; Turcotte-Tremblay, Anne-Marie; Fotso, Jean-Claude Taptué; Tamga, Denise Magne; Yumo, Habakkuk Azinyui; Kouokam, Estelle; Ridde, Valery

2017-08-01

More than 30 countries in sub-Saharan Africa have introduced performance-based financing (PBF) in their healthcare systems. Yet, there has been little research on the process by which PBF was put on the national policy agenda in Africa. This study examines the policy process behind the introduction of PBF program in Cameroon. The research is an explanatory case study using the Kingdon multiple streams framework. We conducted a document review and 25 interviews with various types of actors involved in the policy process. We conducted thematic analysis using a hybrid deductive-inductive approach for data analysis. By 2004, several reports and events had provided evidence on the state of the poor health outcomes and health financing in the country, thereby raising awareness of the situation. As a result, decision-makers identified the lack of a suitable health financing policy as an important issue that needed to be addressed. The change in the political discourse toward more accountability made room to test new mechanisms. A group of policy entrepreneurs from the World Bank, through numerous forms of influence (financial, ideational, network and knowledge-based) and building on several ongoing reforms, collaborated with senior government officials to place the PBF program on the agenda. The policy changes occurred as the result of two open policy windows (i.e. national and international), and in both instances, policy entrepreneurs were able to couple the policy streams to effect change. The policy agenda of PBF in Cameroon underlined the importance of a perceived crisis in the policy reform process and the advantage of building a team to carry forward the policy process. It also highlighted the role of other sources of information alongside scientific evidence (eg.: workshop and study tour), as well as the role of previous policies and experiences, in shaping or influencing respectively the way issues are framed and reformers' actions and choices.

The effect of oxygen content during an initial sustained inflation on heart rate in asphyxiated near-term lambs.

Science.gov (United States)

Sobotka, K S; Ong, T; Polglase, G R; Crossley, K J; Moss, T J M; Hooper, S B

2015-07-01

At birth, an initial sustained inflation (SI) uniformly aerates the lungs, increases arterial oxygenation and rapidly improves circulatory recovery in asphyxiated newborns. We hypothesised that lung aeration, in the absence of an increase in arterial oxygenation, can increase heart rate (HR) in asphyxiated near-term lambs. Lambs were delivered and instrumented at 139±2 days of gestation. Asphyxia was induced by umbilical cord clamping and then delaying the onset of ventilation until mean carotid arterial pressures (CAPs) had decreased <20 mm Hg. Lambs then received a single 30-s SI using nitrogen (N2; n=6), 5% oxygen (O2; n=6), 21% O2 (n=6) or 100% O2 (n=6) followed by ventilation in air for 30 min. HR, CAP and pulmonary blood flow (PBF) were continuously recorded. HR and PBF increased more quickly in lambs resuscitated with 100% and 21% O2 than with 5% O2 or N2. HR and PBF recovery in the 5% O2 group was delayed relative to all other oxygen SI groups. HR in 5%, 21% and 100% O2 groups reached 100 bpm before the SI was complete. HR and PBF in the N2 group did not increase until 10 s after the SI was completed and ventilation was initiated with air. CAP tended to increase quicker in all O2 groups than in N2 group. Oxygen content during an SI is important for circulatory recovery in asphyxiated lambs. This increase in HR is likely driven by the increase in PBF and venous return to the heart. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Glass fiber reinforced concrete for terrestrial photovoltaic arrays

Science.gov (United States)

Maxwell, H.

1979-01-01

The use of glass-fiber-reinforced concrete (GRC) as a low-cost structural substrate for terrestrial solar cell arrays is discussed. The properties and fabrication of glass-reinforced concrete structures are considered, and a preliminary design for a laminated solar cell assembly built on a GRC substrate is presented. A total cost for such a photovoltaic module, composed of a Korad acrylic plastic film front cover, an aluminum foil back cover, an ethylene/vinyl acetate pottant/adhesive and a cotton fabric electrical isolator in addition to the GRC substrate, of $9.42/sq m is projected, which is less than the $11.00/sq m cost goal set by the Department of Energy. Preliminary evaluations are concluded to have shown the design capabilities and cost effectiveness of GRC; however, its potential for automated mass production has yet to be evaluated.

A Metallurgical Evaluation of the Powder-Bed Laser Additive Manufactured 4140 Steel Material

Science.gov (United States)

Wang, Wesley; Kelly, Shawn

2016-03-01

Using laser powder bed fusion (PBF-L) additive manufacturing (AM) process for steel or iron powder has been attempted for decades. This work used a medium carbon steel (AISI 4140) powder to explore the feasibility of AM. The high carbon equivalent of 4140 steel (CEIIW ≈ 0.83) has a strong tendency toward cold cracking. As such, the process parameters must be carefully controlled to ensure the AM build quality. Through an orthogonally designed experimental matrix, a laser-welding procedure was successfully developed to produce 4140 steel AM builds with no welding defects. In addition, the microstructure and micro-cleanliness of the as-welded PBF-L AM builds were also examined. The results showed an ultra-fine martensite lath structure and an ultra-clean internal quality with minimal oxide inclusion distribution. After optimizing the PBF-L AM process parameters, including the laser power and scan speed, the as-welded AM builds yielded an average tensile strength higher than 1482 MPa and an average 33 J Charpy V-notch impact toughness at -18°C. The surface quality, tensile strength, and Charpy V-notch impact toughness of AM builds were comparable to the wrought 4140 steel. The excellent mechanical properties of 4140 steel builds created by the PBF-L AM AM process make industrial production more feasible, which shows great potential for application in the aerospace, automobile, and machinery industries.

Region of interest-based versus whole-lung segmentation-based approach for MR lung perfusion quantification in 2-year-old children after congenital diaphragmatic hernia repair

International Nuclear Information System (INIS)

Weis, M.; Sommer, V.; Hagelstein, C.; Schoenberg, S.O.; Neff, K.W.; Zoellner, F.G.; Zahn, K.; Schaible, T.

2016-01-01

With a region of interest (ROI)-based approach 2-year-old children after congenital diaphragmatic hernia (CDH) show reduced MR lung perfusion values on the ipsilateral side compared to the contralateral. This study evaluates whether results can be reproduced by segmentation of whole-lung and whether there are differences between the ROI-based and whole-lung measurements. Using dynamic contrast-enhanced (DCE) MRI, pulmonary blood flow (PBF), pulmonary blood volume (PBV) and mean transit time (MTT) were quantified in 30 children after CDH repair. Quantification results of an ROI-based (six cylindrical ROIs generated of five adjacent slices per lung-side) and a whole-lung segmentation approach were compared. In both approaches PBF and PBV were significantly reduced on the ipsilateral side (p always <0.0001). In ipsilateral lungs, PBF of the ROI-based and the whole-lung segmentation-based approach was equal (p=0.50). In contralateral lungs, the ROI-based approach significantly overestimated PBF in comparison to the whole-lung segmentation approach by approximately 9.5 % (p=0.0013). MR lung perfusion in 2-year-old children after CDH is significantly reduced ipsilaterally. In the contralateral lung, the ROI-based approach significantly overestimates perfusion, which can be explained by exclusion of the most ventral parts of the lung. Therefore whole-lung segmentation should be preferred. (orig.)

Region of interest-based versus whole-lung segmentation-based approach for MR lung perfusion quantification in 2-year-old children after congenital diaphragmatic hernia repair

Energy Technology Data Exchange (ETDEWEB)

Weis, M.; Sommer, V.; Hagelstein, C.; Schoenberg, S.O.; Neff, K.W. [Heidelberg University, Institute of Clinical Radiology and Nuclear Medicine, University Medical Center Mannheim, Medical Faculty Mannheim, Mannheim (Germany); Zoellner, F.G. [Heidelberg University, Computer Assisted Clinical Medicine, Medical Faculty Mannheim, Mannheim (Germany); Zahn, K. [University of Heidelberg, Department of Paediatric Surgery, University Medical Center Mannheim, Medical Faculty Mannheim, Mannheim (Germany); Schaible, T. [Heidelberg University, Department of Paediatrics, University Medical Center Mannheim, Medical Faculty Mannheim, Mannheim (Germany)

2016-12-15

With a region of interest (ROI)-based approach 2-year-old children after congenital diaphragmatic hernia (CDH) show reduced MR lung perfusion values on the ipsilateral side compared to the contralateral. This study evaluates whether results can be reproduced by segmentation of whole-lung and whether there are differences between the ROI-based and whole-lung measurements. Using dynamic contrast-enhanced (DCE) MRI, pulmonary blood flow (PBF), pulmonary blood volume (PBV) and mean transit time (MTT) were quantified in 30 children after CDH repair. Quantification results of an ROI-based (six cylindrical ROIs generated of five adjacent slices per lung-side) and a whole-lung segmentation approach were compared. In both approaches PBF and PBV were significantly reduced on the ipsilateral side (p always <0.0001). In ipsilateral lungs, PBF of the ROI-based and the whole-lung segmentation-based approach was equal (p=0.50). In contralateral lungs, the ROI-based approach significantly overestimated PBF in comparison to the whole-lung segmentation approach by approximately 9.5 % (p=0.0013). MR lung perfusion in 2-year-old children after CDH is significantly reduced ipsilaterally. In the contralateral lung, the ROI-based approach significantly overestimates perfusion, which can be explained by exclusion of the most ventral parts of the lung. Therefore whole-lung segmentation should be preferred. (orig.)

Twelve months of implementation of health care performance-based financing in Burkina Faso: A qualitative multiple case study.

Science.gov (United States)

Ridde, Valéry; Yaogo, Maurice; Zongo, Sylvie; Somé, Paul-André; Turcotte-Tremblay, Anne-Marie

2018-01-01

To improve health services' quantity and quality, African countries are increasingly engaging in performance-based financing (PBF) interventions. Studies to understand their implementation in francophone West Africa are rare. This study analysed PBF implementation in Burkina Faso 12 months post-launch in late 2014. The design was a multiple and contrasted case study involving 18 cases (health centres). Empirical data were collected from observations, informal (n = 224) and formal (n = 459) interviews, and documents. Outside the circle of persons trained in PBF, few in the community had knowledge of it. In some health centres, the fact that staff were receiving bonuses was intentionally not announced to populations and community leaders. Most local actors thought PBF was just another project, but the majority appreciated it. There were significant delays in setting up agencies for performance monitoring, auditing, and contracting, as well as in the payment. The first audits led rapidly to coping strategies among health workers and occasionally to some staging beforehand. No community-based audits had yet been done. Distribution of bonuses varied from one centre to another. This study shows the importance of understanding the implementation of public health interventions in Africa and of uncovering coping strategies. © 2017 The Authors. The International Journal of Health Planning and Management Published by John Wiley & Sons Ltd.

US Army Armor Reference Data in Three Volumes. Volume I. The Army Division.

Science.gov (United States)

1981-01-01

14 FADIO SET AN/GRC-106 . . . . .. . ........ . .. 1 ACHI EGUN 7.92--M VEH FIXS D. .............. 3 RADIO SET AN/GRC-160 ......... .................. 6...8 RADIAC SET AN/POR-27 ...................................... 1 MAC EGUN CAL .50 19 FLEX FOR CIOUJD aE ................... 8

Development of magnetic resonance technology for noninvasive boron quantification

International Nuclear Information System (INIS)

Bradshaw, K.M.

1990-11-01

Boron magnetic resonance imaging (MRI) and spectroscopy (MRS) were developed in support of the noninvasive boron quantification task of the Idaho National Engineering Laboratory (INEL) Power Burst Facility/Boron Neutron Capture Therapy (PBF/BNCT) program. The hardware and software described in this report are modifications specific to a GE Signa trademark MRI system, release 3.X and are necessary for boron magnetic resonance operation. The technology developed in this task has been applied to obtaining animal pharmacokinetic data of boron compounds (drug time response) and the in-vivo localization of boron in animal tissue noninvasively. 9 refs., 21 figs

Working With New Designs

DEFF Research Database (Denmark)

Visholm, Steen; Beck, Ulla Charlotte

2014-01-01

In this paper the learning concept of group relations conferences are discussed. The authors have worked with group relations conferences (GRC) in different contexts for many years-mainly as a part of educational programmes for managers and consultants (OPU at IGA Copenhagen, MPO at Roskilde...... University, and NAPSO). Seen from the horizon of their experience some of the basic concepts in the theories about GRC need clarifying, revision, and development. The GRC is a part of the learning from experience movement and as a consequence it stresses the underlying basis: learning is personal so everyone...... decides for themselves what makes sense and what does not. This principle sometimes work as a defence against a closer examination of the two questions: does GRCs provide relevant experiences to learn from, and what is it you learn or can expect to learn at a GRC. While two earlier papers (Beck & Visholm...

Integration of NASA-Developed Lifing Technology for PM Alloys into DARWIN (registered trademark)

Science.gov (United States)

McClung, R. Craig; Enright, Michael P.; Liang, Wuwei

2011-01-01

In recent years, Southwest Research Institute (SwRI) and NASA Glenn Research Center (GRC) have worked independently on the development of probabilistic life prediction methods for materials used in gas turbine engine rotors. The two organizations have addressed different but complementary technical challenges. This report summarizes a brief investigation into the current status of the relevant technology at SwRI and GRC with a view towards a future integration of methods and models developed by GRC for probabilistic lifing of powder metallurgy (P/M) nickel turbine rotor alloys into the DARWIN (Darwin Corporation) software developed by SwRI.

Advanced Stirling Radioisotope Generator Engineering Unit 2 (ASRG EU2) Final Assembly

Science.gov (United States)

Oriti, Salvatore M.

2015-01-01

NASA Glenn Research Center (GRC) has recently completed the assembly of a unique Stirling generator test article for laboratory experimentation. Under the Advanced Stirling Radioisotope Generator (ASRG) flight development contract, NASA GRC initiated a task to design and fabricate a flight-like generator for in-house testing. This test article was given the name ASRG Engineering Unit 2 (EU2) as it was effectively the second engineering unit to be built within the ASRG project. The intent of the test article was to duplicate Lockheed Martin's qualification unit ASRG design as much as possible to enable system-level tests not previously possible at GRC. After the cancellation of the ASRG flight development project, the decision was made to continue the EU2 build, and make use of a portion of the hardware from the flight development project. GRC and Lockheed Martin engineers collaborated to develop assembly procedures, leveraging the valuable knowledge gathered by Lockheed Martin during the ASRG development contract. The ASRG EU2 was then assembled per these procedures at GRC with Lockheed Martin engineers on site. The assembly was completed in August 2014. This paper details the components that were used for the assembly, and the assembly process itself.

African American Men, Gender Role Conflict, and Psychological Distress: The Role of Racial Identity

Science.gov (United States)

Wester, Stephen R.; Vogel, David L.; Wei, Meifen; McLain, Rodney

2006-01-01

Little research exists exploring the intersection of male gender role conflict (GRC), racial identity, and psychological distress. Accordingly, using a sample of 130 self-identified African American male participants, this study explored which aspects of racial identity mediated the relationship between GRC and psychological distress. Results…

Preparation and Performance of Poly(butyl fumarate-Based Material for Potential Application in LED Encapsulation

Directory of Open Access Journals (Sweden)

Liang Wang

2017-02-01

Full Text Available A UV-curable poly(butyl fumarate (PBF/poly(propylene fumarate-diacrylate (PPF-DA hybrid material with good performance for LED encapsulation is introduced in the paper. They have been prepared by radical polymerization using PBF and PPF-DA macromers with a UV curing system. PBF and PPF-DA were characterized by Fourier-transform infrared (FT-IR and H-nuclear magnetic resonance (1H NMR. The thermal behavior, optical and mechanical properties of the material were examined by thermogravimetric analysis (TGA, differential scanning calorimetry (DSC, ultraviolet-visible spectroscopy (UV–vis, and a material testing system mechanical testing machine, respectively. The results indicated that the hybrid material has a suitable refractive index (n = 1.537 and high transmittance (99.64% in visible range before/after thermal aging. With the increasing of the double bond ratio from 0.5 to 2, the water absorption ratios of the prepared encapsulation material were 1.22%, 1.87% and 2.88%, respectively. The mechanical property experiments showed that bonding strength was in the range of 1.86–3.40 MPa, tensile-shear strength ranged from 0.84 MPa to 1.57 MPa, and compression strength was in the range of 5.10–27.65 MPa. The cured PBF/PPF-DA hybrid material can be used as a light-emitting diode (LED encapsulant, owing to its suitable refractive index, high transparency, excellent thermal stability, lower water absorption, and good mechanical properties.

Body adiposity index versus body mass index and other anthropometric traits as correlates of cardiometabolic risk factors.

Directory of Open Access Journals (Sweden)

Charlene T Lichtash

Full Text Available The worldwide prevalence of obesity mandates a widely accessible tool to categorize adiposity that can best predict associated health risks. The body adiposity index (BAI was designed as a single equation to predict body adiposity in pooled analysis of both genders. We compared body adiposity index (BAI, body mass index (BMI, and other anthropometric measures, including percent body fat (PBF, in their correlations with cardiometabolic risk factors. We also compared BAI with BMI to determine which index is a better predictor of PBF.The cohort consisted of 698 Mexican Americans. We calculated correlations of BAI, BMI, and other anthropometric measurements (PBF measured by dual energy X-ray absorptiometry, waist and hip circumference, height, weight with glucose homeostasis indices (including insulin sensitivity and insulin clearance from euglycemic clamp, lipid parameters, cardiovascular traits (including carotid intima-media thickness, and biomarkers (C-reactive protein, plasminogen activator inhibitor-1 and adiponectin. Correlations between each anthropometric measure and cardiometabolic trait were compared in both sex-pooled and sex-stratified groups.BMI was associated with all but two measured traits (carotid intima-media thickness and fasting glucose in men, while BAI lacked association with several variables. BAI did not outperform BMI in its associations with any cardiometabolic trait. BAI was correlated more strongly than BMI with PBF in sex-pooled analyses (r = 0.78 versus r = 0.51, but not in sex-stratified analyses (men, r = 0.63 versus r = 0.79; women, r = 0.69 versus r = 0.77. Additionally, PBF showed fewer correlations with cardiometabolic risk factors than BMI. Weight was more strongly correlated than hip with many of the cardiometabolic risk factors examined.BAI is inferior to the widely used BMI as a correlate of the cardiometabolic risk factors studied. Additionally, BMI's relationship with total adiposity

Reflections on Centaur Upper Stage Integration by the NASA Lewis (Glenn) Research Center

Science.gov (United States)

Graham, Scott R.

2015-01-01

The NASA Glenn (then Lewis) Research Center (GRC) led several expendable launch vehicle (ELV) projects from 1963 to 1998, most notably the Centaur upper stage. These major, comprehensive projects included system management, system development, integration (both payload and stage), and launch operations. The integration role that GRC pioneered was truly unique and highly successful. Its philosophy, scope, and content were not just invaluable to the missions and vehicles it supported, but also had significant Agency-wide benefits. An overview of the NASA Lewis Research Center (now the NASA Glenn Research Center) philosophy on ELV integration is provided, focusing on Atlas/Centaur, Titan/Centaur, and Shuttle/Centaur vehicles and programs. The necessity of having a stable, highly technically competent in-house staff is discussed. Significant depth of technical penetration of contractor work is another critical component. Functioning as a cohesive team was more than a concept: GRC senior management, NASA Headquarters, contractors, payload users, and all staff worked together. The scope, content, and history of launch vehicle integration at GRC are broadly discussed. Payload integration is compared to stage development integration in terms of engineering and organization. Finally, the transition from buying launch vehicles to buying launch services is discussed, and thoughts on future possibilities of employing the successful GRC experience in integrating ELV systems like Centaur are explored.

Common issues raised during the quality assurance process of WHO guidelines: a cross-sectional study.

Science.gov (United States)

Porgo, Teegwendé V; Ferri, Mauricio; Norris, Susan L

2018-02-07

In 2007, WHO established the Guidelines Review Committee (GRC) to ensure that WHO guidelines adhere to the highest international standards. The GRC reviews guideline proposals and final guidelines. The objectives of this study were to examine the rates of and reasons for conditional approval and non-approval of documents submitted for the first time to the GRC, and calculate the time intervals and numbers of submissions to achieve approval for documents conditionally approved or not approved at first submission. All initial submissions to the GRC between 2014 and 2017 were examined. Data were extracted from the GRC's records of written comments and discussions. Of a total of 85 proposals and 88 final guidelines, 32 (37.6%) proposals and 37 (42.0%) final guidelines were conditionally approved, and 15 (17.6%) proposals and 28 (31.8%) final guidelines were not. For both conditionally approved and not approved proposals, the most frequent reasons were suboptimal composition or inadequate description of the guideline contributor groups (in all proposals), followed by inadequate formulation of key questions (in 90.6% of conditionally approved proposals and all not approved proposals). For both conditionally approved and not approved final guidelines, the most frequent reasons were problems with recommendations (in all final guidelines), followed by inappropriate methods for evidence retrieval or an inadequate description thereof (in all conditionally approved final guidelines and 75.0% of not approved final guidelines). The median time to achieve approval was 2 months for proposals and 1-2 months for final guidelines. The median number of submissions was 2 for proposals and 2-2.5 for final guidelines. The GRC implements a rigorous quality assurance process and identifies problems with a significant percentage of initial submissions. WHO needs to continuously evaluate its guideline development processes to inform effective quality improvement measures and optimise the

Long working hours and overweight and obesity in working adults.

Science.gov (United States)

Kim, Byung-Mi; Lee, Bo-Eun; Park, Hye-Sook; Kim, Young-Ju; Suh, Young-Ju; Kim, Jeong-Youn; Shin, Ji-Young; Ha, Eun-Hee

2016-01-01

Previous studies have identified a link between gender and the various risk factors associated with obesity. We examined obesity risk factors in working adults to identify the effects of differences in body mass index (BMI) and percentage body fat (PBF) between women and men. A total of 1,120 adults agreed to participate in the study. Data from 711 participants, including 411 women and 300 men, were analyzed. Multiple logistic regression analysis was used to estimate the effects of risk factors on obesity and being overweight. In addition, the least-squares (LS) means of both BMI and PBF were estimated by analysis of covariance (ANCOVA) in a generalized linear model. Increases in BMI and PBF were significantly related to an age > 50 years and long working hours in women after compensating for confounding factors. Using the PBF criterion, the odds ratio (OR) of being overweight or obese in women > 50 years of age who worked for > 9 h a day was 3.9 (95% confidence interval [CI], 1.05-11.00). For BMI, women who were > 50 years of age and worked for > 9 h a day were 3.82 times (95% CI, 1.31-11.14) more likely to be overweight or obese than those who were worked for working adults was associated with > 50 years of age and long working hours in women. Further studies are needed to investigate the underlying mechanisms of this relationship and its potential implications for the prevention and management of excess weight and obesity.

Gender role conflict among African American men who have sex with men and women: associations with mental health and sexual risk and disclosure behaviors.

Science.gov (United States)

Bingham, Trista A; Harawa, Nina T; Williams, John K

2013-01-01

We investigated whether high gender role conflict (GRC; internal conflict with traditional gender-role stereotypes and an individual's perceived need to comply with these roles) is associated with psychological distress and HIV-related risk behaviors in a sample of African American men who have sex with men and women (MSMW). We analyzed baseline data collected from questionnaires completed by 400 MSMW participating in the Men of African American Legacy Empowering Self project in Los Angeles, California, in 2007 to 2010 for associations between participants' GRC and experiences of poor mental health and HIV risk outcomes. MSMW who reported higher levels of GRC than other participants also reported more psychological distress, lower self-esteem, greater internalized homophobia, less HIV knowledge, lower risk reduction skills, less disclosure of same-sex behaviors to others, and more unprotected vaginal or anal intercourse with female partners. Future research should consider how high GRC affects African American MSMW's lives and identify specific approaches to help alleviate the psychological distress and other negative behavioral outcomes associated with internal conflict caused by rigid gender role socialization.

The Value of Successful MBSE Adoption

Science.gov (United States)

Parrott, Edith

2016-01-01

The value of successful adoption of Model Based System Engineering (MBSE) practices is hard to quantify. Most engineers and project managers look at the success in terms of cost. But there are other ways to quantify the value of MBSE and the steps necessary to achieve adoption. The Glenn Research Center (GRC) has been doing Model-Based Engineering (design, structural, etc.) for years, but the system engineering side has not. Since 2010, GRC has been moving from documents centric to MBSE/SysML. Project adoption of MBSE has been slow, but is steadily increasing in both MBSE usage and complexity of generated products. Sharing of knowledge of lessons learned in the implementation of MBSE/SysML is key for others who want to be successful. Along with GRC's implementation, NASA is working hard to increase the successful implementation of MBSE across all the other centers by developing guidelines, templates and libraries for projects to utilize. This presentation will provide insight into recent GRC and NASA adoption efforts, lessons learned and best practices.

Application of Autonomous Spacecraft Power Control Technology to Terrestrial Microgrids

Science.gov (United States)

Dever, Timothy P.; Trase, Larry M.; Soeder, James F.

2014-01-01

This paper describes the potential of the power campus located at the NASA Glenn Research Center (GRC) in Cleveland, Ohio for microgrid development. First, the benefits provided by microgrids to the terrestrial power grid are described, and an overview of Technology Needs for microgrid development is presented. Next, GRC's work on development of autonomous control for manned deep space vehicles, which are essentially islanded microgrids, is covered, and contribution of each of these developments to the microgrid Technology Needs is detailed. Finally, a description is provided of GRC's existing physical assets which can be applied to microgrid technology development, and a phased plan for development of a microgrid test facility is presented.

Communications Related to Weather Information Handling and Dissemination

Science.gov (United States)

Dhas, Chris

2000-01-01

This report summarizes the tasking contained in the Statement of Work and describes the results of the project. In addition, it addresses the principles, procedures, and methods of application that would be generally applicable to using the results of the project. NASA Glenn Research Center (GRC) is involved in the Aviation Weather Information (AWIN) Program, which has a goal of reducing the aircraft accident rate, by a factor of five within 10 years and by a factor of 10 within 20 years. GRC's effort concentrates on the communications means needed to disseminate effective weather data. GRC's focus in on developing new technologies and techniques to support the digital communication of weather information between airborne and ground-based users.

Um debate tridimensional sobre os padrões de proteção social no Brasil frente à crise capitalista internacional : o caso do Bolsa Família

OpenAIRE

Maurício, Márcio Fernandes

2011-01-01

Esta dissertação propõe um debate teórico sobre os padrões de proteção social no Brasil frente à crise capitalista internacional, com um estudo de caso sobre o Programa Bolsa Família (PBF). O recorte de análise consiste na articulação do PBF com os chamados "programas complementares", no âmbito da coordenação intergovernamental e interdependência organizacional, preconizadas na Constituição Federal de 1988. E, o objeto de análise, neste caso, corresponde ao debate teórico propriamente dito. A...

Recent developments in high-speed, non-sampling electromagnetic calorimetry

International Nuclear Information System (INIS)

Anderson, D.F.; Ramberg, E.J.

1990-03-01

Brief discussions are given of the work that has been done on the suppression of the slow component in BaF 2 , the developments in the understanding of undoped CsI, and the properties of the new scintillator CeF 3 . The properties of the Cherenkov radiator PbF 2 along with test beam results are presented. Monte Carlo simulations indicate that, with the addition of a small amount of scintillator, PbF 2 , can be made hadron compensating off-line so that the resolution of a compensating hadron calorimeter will not be degraded by its presence. 14 refs., 6 figs., 4 tabs

14 CFR 1206.401 - Location of NASA Information Centers.

Science.gov (United States)

2010-01-01

... Locator (URL) addresses are as follows: (1) (HQ) http://www.hq.nasa.gov/office/pao/FOIA/; (2) (ARC) http://george.arc.nasa.gov/dx/FOIA/elec.html; (3) (DFRC) http://www.dfrc.nasa.gov/FOIA/readroom.html; (4) (GRC) http://www.grc.nasa.gov/WWW/FOIA/ReadingRm.htm; (5) (GSFC) http://genesis.gsfc.nasa.gov//foia/read-rm...

Programa Bolsa Família: a interface entre a atuação profissional e o direito humano a alimentação adequada The "Bolsa Família" family grant scheme: the interface between professional practice and the human right to adequate food and nutrition

Directory of Open Access Journals (Sweden)

Camila Irigonhé Ramos

2012-08-01

Full Text Available O Direito Humano à Alimentação Adequada deve ser garantido através de políticas públicas de Segurança Alimentar e Nutricional (SAN. Nesse contexto está inserido o Programa Bolsa Família (PBF, que, além da transferência de renda, visa a garantia de acesso aos direitos sociais básicos. Este estudo objetiva analisar a operacionalização do PBF e, consequentemente, o entendimento dos profissionais de saúde a respeito do programa, enquanto eixo estruturante da política pública de SAN. Para isso, realizou-se entrevistas semiestruturadas com trabalhadores da atenção primária, envolvidos diretamente, tanto com o PBF, quanto com as famílias que recebem este beneficio. Ao final do estudo, foi possível evidenciar a importância da formação dos profissionais que atuam nessa área, pois, ao desconectar a realidade social em que os beneficiários estão inseridos, dos objetivos do programa, colabora-se para a simples mecanização dessas práticas. Nesse sentido, aponta-se que os profissionais de saúde precisam entender as proposições do programa como estratégias político-sociais, as quais, para além do alívio imediato, visam a superação dos problemas relacionados à pobreza e à fome.The Human Right to Adequate Nutrition must be ensured through the public policies included in SAN, namely the Food and Nutritional Security campaign. Besides the income transfer geared to ensuring access to basic social rights, the "Bolsa Família" Program (PBF is included in this context. This study seeks to analyze the operational aspects of the PBF and also ascertain whether or not the health professionals see the program as a core element of the SAN public policy. With this in mind, semi-structured interviews were conducted with primary healthcare workers involved directly both with the PBF and with the families who receive this benefit. By the end of the study, it was possible to perceive the importance of training health professionals who

Correlation of adiposity indices with cardiovascular disease risk factors in healthy adults of Singapore: a cross-sectional study.

Science.gov (United States)

Bi, Xinyan; Tey, Siew Ling; Leong, Claudia; Quek, Rina; Loo, Yi Ting; Henry, Christiani Jeyakumar

2016-01-01

Obesity has long been highlighted for its association with increased incidence of cardiovascular disease (CVD). Nonetheless, the best adiposity indices to evaluate the CVD risk factors remain contentious and few studies have been performed in Asian populations. In the present study, we compared the association strength of percent body fat (PBF) to indirect anthropometric measures of general adiposity (body mass index (BMI) and body adiposity index (BAI)) and central adiposity (waist circumference (WC), and waist-to-hip ratio (WHR)) for the prediction of CVD risk factors in healthy men and women living in Singapore. A total of 125 individuals (63 men and 62 women) took part in this study. PBF was measured by using three different techniques, including bioelectrical impedance analysis (BIA), BOD POD, and dual-energy X-ray absorptiometry (DEXA). Anthropometric measurements (WC, hip circumference (HC), height, and weight), fasting blood glucose (FBG), fasting serum insulin (FSI), and lipid profiles were determined according to standard protocols. Correlations of anthropometric measurements and PBF with CVD risk factors were compared. Irrespective of the measuring techniques, PBF showed strong positive correlations with FSI, HOMA-IR, TC/HDL, TG/HDL, and LDL/HDL in both genders. While PBF was highly correlated with FBG, SBP, and DBP in females, no significant relationships were observed in males. Amongst the five anthropometric measures of adiposity, BAI was the best predictor for CVD risk factors in female participants (r = 0.593 for HOMA-IR, r = 0.542 for TG/HDL, r = 0.474 for SBP, and r = 0.448 for DBP). For males, the combination of WC (r = 0.629 for HOMA-IR, and r = 0.446 for TG/HDL) and WHR (r = 0.352 for SBP, and r = 0.366 for DBP) had the best correlation with CVD risk factors. Measurement of PBF does not outperform the simple anthropometric measurements of obesity, i.e. BAI, WC, and WHR, in the prediction of CVD risk factors in

InSitu SEM Investigation of Microstructural Damage Evolution and Strain Relaxation in a Melt Infiltrated SiC/SiC Composite

Science.gov (United States)

Sevener, Kathy; Chen, Zhe; Daly, Sam; Tracy, Jared; Kiser, Doug

2016-01-01

With CMC components poised to complete flight certification in turbine engines on commercial aircraft within the near future, there are many efforts within the aerospace community to model the mechanical and environmental degradation of CMCs. Direct observations of damage evolution are needed to support these modeling efforts and provide quantitative measures of damage parameters used in the various models. This study was performed to characterize the damage evolution during tensile loading of a melt infiltrated (MI) silicon carbide reinforced silicon carbide (SiC/SiC) composite. A SiC/SiC tensile coupon was loaded to a maximum global stress of 30 ksi in a tensile fixture within an SEM while observations were made at 5 ksi increments. Both traditional image analysis and DIC (digital image correlation) were used to quantify damage evolution. With the DIC analysis, microscale damage was observed at the fiber-matrix interfaces at stresses as low as 5 ksi. First matrix cracking took place between 20 and 25 ksi, accompanied by an observable relaxation in strain near matrix cracks. Matrix crack opening measurements at the maximum load ranged from 200 nm to 1.5 m. Crack opening along the fiber-matrix interface was also characterized as a function of load and angular position relative to the loading axis. This characterization was funded by NASA GRC and was performed to support NASA GRC modeling of SiC/SiC environmental degradation

Alternative Bio-Derived JP-8 Class Fuel and JP-8 Fuel: Flame Tube Combustor Test Results Compared using a GE TAPS Injector Configuration

Science.gov (United States)

Hicks, Yolanda R.; Anderson, Robert; Tedder, Sarah

2016-01-01

This paper presents results from tests in a NASA Glenn Research Center (GRC) flame tube facility, where a bio-derived alternate fuel was compared with JP-8 for emissions and general combustion performance. A research version of General Electric Aviation (GE) TAPS injector was used for the tests. Results include 2D, planar laser-based imaging as well as basic flow visualization of the flame. Four conditions were selected that simulate various engine power conditions relevant to NASA Fundamental Aeronautics Supersonics and Environmentally Responsible Aviation Projects were tested.

Army 86 Cost Sensitivity Analysis.

Science.gov (United States)

1980-05-01

NI VI AN/PVS-4 W/IMG 5 Q15414 RADAR ST AN/MPQ-4A LP 25 Q16110 RADAR SET AN/PPS- SALP 773 Q34308 RADIO SET AN/GRC-160 191 Q45779 RADIO SET AN/VRC-12 654...VI AN/PVS-4 W/ING 5 Q15414 RADAR ST AN/MPQ-4A LP 25 Q16110 RADAR SET AN/PPS- SALP 592 Q34308 RADIO SET AN/GRC-160 555 Q38299 RADIO SET AN/PRC-25 474...PVS-4 W/IMG Q15414 RADAR ST AN/MPQ-4A LP Q16110 RADAR SET AN/PPS- SALP Q34308 RADIO SET AN/GRC-160 Q38299 RADIO SET AN/PRC-25 Q45779 RADIO SET AN/VRC-12

Overview of NASA Magnet and Linear Alternator Research Efforts

Science.gov (United States)

Geng, Steven M.; Niedra, Janis M.; Schwarze, Gene E.

2005-02-01

The Department of Energy, Lockheed Martin, Stirling Technology Company, and NASA Glenn Research Center are developing a high-efficiency, 110 watt Stirling Radioisotope Generator (SRG110) for NASA Space Science missions. NASA Glenn is conducting in-house research on rare earth permanent magnets and on linear alternators to assist in developing a free-piston Stirling convertor for the SRG110 and for developing advanced technology. The permanent magnet research efforts include magnet characterization, short-term magnet aging tests, and long-term magnet aging tests. Linear alternator research efforts have begun just recently at GRC with the characterization of a moving iron type linear alternator using GRC's alternator test rig. This paper reports on the progress and future plans of GRC's magnet and linear alternator research efforts.

Slowing and cooling of heavy or light (even with a tiny electric dipole moment) polar molecules using a novel, versatile electrostatic Stark decelerator.

Science.gov (United States)

Wang, Qin; Hou, Shunyong; Xu, Liang; Yin, Jianping

2016-02-21

To meet some demands for realizing precise measurements of an electric dipole moment of electron (eEDM) and examining cold collisions or cold chemical physics, we have proposed a novel, versatile electrostatic Stark decelerator with an array of true 3D electric potential wells, which are created by a series of horizontally-oriented, U-shaped electrodes with time-sequence controlling high voltages (± HV) and two guiding electrodes with a constant voltage. We have calculated the 2D electric field distribution, the Stark shifts of the four lowest rotational sub-levels of PbF molecules in the X1(2)Π1/2(v = 0) electronic and vibrational ground states as well as the population in the different rotational levels. We have discussed the 2D longitudinal and transverse phase-space acceptances of PbF molecules in our decelerator. Subsequently, we have simulated the dynamic processes of the decelerated PbF molecules using the 3D Monte-Carlo method, and have found that a supersonic PbF beam with a velocity of 300 m s(-1) can be efficiently slowed to about 5 m s(-1), which will greatly enhance the sensitivities to research a parity violation and measure an eEDM. In addition, we have investigated the dependences of the longitudinal velocity spread, longitudinal temperature and bunching efficiency on both the number of guiding stages and high voltages, and found that after bunching, a cold packet of PbF molecules in the J = 7/2, MΩ = -7/4 state with a longitudinal velocity spread of 0.69 m s(-1) (corresponding to a longitudinal temperature of 2.35 mK) will be produced by our high-efficient decelerator, which will generate a high energy-resolution molecular beam for studying cold collision physics. Finally, our novel decelerator can also be used to efficiently slow NO molecules with a tiny electric dipole moment (EDM) of 0.16 D from 315 m s(-1) to 28 m s(-1). It is clear that our proposed new decelerator has a good slowing performance and experimental feasibility as well as wide

Signal Processing Effects for Ultrasonic Guided Wave Scanning of Composites

International Nuclear Information System (INIS)

Roth, D.J.; Cosgriff, L.M.; Martin, R.E.; Burns, E.A.; Teemer, L.

2005-01-01

The goal of this ongoing work is to optimize experimental variables for a guided wave scanning method to obtain the most revealing and accurate images of defect conditions in composite materials. This study focuses on signal processing effects involved in forming guided wave scan images. Signal processing is involved at two basic levels for deriving ultrasonic guided wave scan images. At the primary level, NASA GRC has developed algorithms to extract over 30 parameters from the multimode signal and its power spectral density. At the secondary level, there are many variables for which values must be chosen that affect actual computation of these parameters. In this study, a ceramic matrix composite sample having a delamination is characterized using the ultrasonic guided wave scan method. Energy balance and decay rate parameters of the guided wave at each scan location are calculated to form images. These images are compared with ultrasonic c-scan and thermography images. The effect of the time portion of the waveform processed on image quality is assessed by comparing with images formed using the total waveform acquired

2009 Clusters, Nanocrystals & Nanostructures GRC

Energy Technology Data Exchange (ETDEWEB)

Wang, Lai-Sheng [Washington State Univ., Pullman, WA (United States)

2009-07-19

For over thirty years, this Gordon Conference has been the premiere meeting for the field of cluster science, which studies the phenomena that arise when matter becomes small. During its history, participants have witnessed the discovery and development of many novel materials, including C60, carbon nanotubes, semiconductor and metal nanocrystals, and nanowires. In addition to addressing fundamental scientific questions related to these materials, the meeting has always included a discussion of their potential applications. Consequently, this conference has played a critical role in the birth and growth of nanoscience and engineering. The goal of the 2009 Gordon Conference is to continue the forward-looking tradition of this meeting and discuss the most recent advances in the field of clusters, nanocrystals, and nanostructures. As in past meetings, this will include new topics that broaden the field. In particular, a special emphasis will be placed on nanomaterials related to the efficient use, generation, or conversion of energy. For example, we anticipate presentations related to batteries, catalysts, photovoltaics, and thermoelectrics. In addition, we expect to address the controversy surrounding carrier multiplication with a session in which recent results addressing this phenomenon will be discussed and debated. The atmosphere of the conference, which emphasizes the presentation of unpublished results and lengthy discussion periods, ensures that attendees will enjoy a valuable and stimulating experience. Because only a limited number of participants are allowed to attend this conference, and oversubscription is anticipated, we encourage all interested researchers from academia, industry, and government institutions to apply as early as possible. An invitation is not required. We also encourage all attendees to submit their latest results for presentation at the poster sessions. We anticipate that several posters will be selected for 'hot topic' oral presentations. Because of the important role that students and postdocs play in the future of this field, we also anticipate to select several posters from young investigators for oral presentations.

The performance of obesity screening tools among young Thai adults.

Science.gov (United States)

Limpawattana, Panita; Kengkijkosol, Thepkhachi; Assantachai, Prasert; Krairit, Orapitchaya; Pimporm, Jiraporn

2014-12-01

Obesity is a worldwide medical condition that leads to physical and psychological impairment. Specific ethnicity, gender and age group are related to different performances of anthropometric indices to predict obesity. The objectives of this study were to estimate the performance of the anthropometric indices for detecting obesity based on percentage of body fat (PBF), to study the correlation among those indices, and to determine the optimal cut-off point of the indices among young Thai adults. This is a cross-sectional study of healthy urban subjects in Khon Kaen, Thailand who were aged 20-39 years. Baseline characteristics and anthropometric measures were collected. PBF was determined using bioelectrical impedance analysis. Demographic data and anthropometric variables were analyzed using descriptive statistics. Receiver-operating characteristic (ROC) curves were used to compare the performance of anthropometric measures as predictors of obesity. One-hundred men and 100 women were recruited for this study. Body mass index (BMI), waist circumference (WC), waist-to-hip ratio (WHR) and waist-to-stature ratio (WSR) were significantly correlated to PBF. BMI demonstrated the best performance according to the area under the ROC curves in both sexes at cut-off points of 22.5 in women or 25 kg/m(2) in men. WC and WSR showed better performance than WHR to detect obesity. In conclusion, anthropometric indices in young Thai adults were correlated well with PBF to predict obesity as shown in prior reports. Different cut-off points of these indices to define obesity in young Thai adults are recommended. The global cut-off points of WSR in women regardless of ethnicity are supported.

Programa Bolsa Família: uma nova modalidade de biopolítica Family Allowance Program: a new type of biopolitics

Directory of Open Access Journals (Sweden)

Rémi Fernand Lavergne

2012-06-01

Full Text Available O propósito deste artigo é mostrar como o Programa Bolsa Família (PBF remete a uma forma de biopolítica nos termos evocados por Michel Foucault e inscreve-se numa perspectiva de normalização, funcionando pela norma e pela regulamentação. Busca também evidenciar como o Serviço Social e a educação "por toda a vida" têm um importante papel nos processos de subjetivação e de produção de subjetividades com vistas a incidir sobre a conduta das populações indigentes e marginalizadas.The purpose of this article is to show how the Family Allowance Program (Programa Bolsa Família - PBF refers to a form of biopolitics such as evoked by Foucault. Besides illustrating how the PBF is inscribed in a normalizing perspective, the article seeks to show how the Social Services and the Education "for a lifetime" play an important role in terms of building up subjectivity processes and subjective opinions and feelings whose aim is to guide and control the poor and marginalized populations' behavior.

Kinetic Risk Factors of Running-Related Injuries in Female Recreational Runners.

Science.gov (United States)

Napier, Christopher; MacLean, Christopher L; Maurer, Jessica; Taunton, Jack E; Hunt, Michael A

2018-05-30

Our objective was to prospectively investigate the association of kinetic variables with running-related injury (RRI) risk. Seventy-four healthy female recreational runners ran on an instrumented treadmill while 3D kinetic and kinematic data were collected. Kinetic outcomes were vertical impact transient, average vertical loading rate, instantaneous vertical loading rate, active peak, vertical impulse, and peak braking force (PBF). Participants followed a 15-week half-marathon training program. Exposure time (hours of running) was calculated from start of program until onset of injury, loss to follow-up, or end of program. After converting kinetic variables from continuous to ordinal variables based on tertiles, Cox proportional hazard models with competing risks were fit for each variable independently, before analysis in a forward stepwise multivariable model. Sixty-five participants were included in the final analysis, with a 33.8% injury rate. PBF was the only kinetic variable that was a significant predictor of RRI. Runners in the highest tertile (PBF recreational runners and should be considered as a target for gait retraining interventions. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

A territorialização do programa Bolsa Família na comunidade rural Sítio Carnaubal – Água Nova/RN: a voz dos beneficiários

Directory of Open Access Journals (Sweden)

Francisca Lima

2017-12-01

Full Text Available O presente artigo realiza um estudo a respeito da pobreza rural a partir do viés da multidimensionalidade e considera o Programa Bolsa Família (PBF, criado pelo Governo Federal do Brasil, uma política pública que vem contribuindo com a minimização da pobreza e tem aumentado a possibilidade de permanência do homem no campo. Nesta perspectiva, o objetivo principal deste trabalho é analisar os impactos do PBF no contexto socioeconômico das famílias beneficiárias residentes na comunidade rural do Sítio Carnaubal no município de Água Nova, uma pequena cidade do Rio Grande do Norte (RN, estado localizado na região nordeste do Brasil. Procura-se compreender, ainda, entre outros aspectos, a territorialização das políticas públicas sociais de combate à pobreza, bem como a territorialização do PBF na comunidade em estudo, com um especial interesse em descobrir de que modo o programa é percebido pelos beneficiários residentes no território referido.

Effect of furosemide on pulmonary blood flow distribution in resting and exercising horses

Science.gov (United States)

Erickson, H. H.; Bernard, S. L.; Glenny, R. W.; Fedde, M. R.; Polissar, N. L.; Basaraba, R. J.; Walther, S. M.; Gaughan, E. M.; McMurphy, R.; Hlastala, M. P.

1999-01-01

We determined the spatial distribution of pulmonary blood flow (PBF) with 15-micron fluorescent-labeled microspheres during rest and exercise in five Thoroughbred horses before and 4 h after furosemide administration (0.5 mg/kg iv). The primary finding of this study was that PBF redistribution occurred from rest to exercise, both with and without furosemide. However, there was less blood flow to the dorsal portion of the lung during exercise postfurosemide compared with prefurosemide. Furosemide did alter the resting perfusion distribution by increasing the flow to the ventral regions of the lung; however, that increase in flow was abated with exercise. Other findings included 1) unchanged gas exchange and cardiac output during rest and exercise after vs. before furosemide, 2) a decrease in pulmonary arterial pressure after furosemide, 3) an increase in the slope of the relationship of PBF vs. vertical height up the lung during exercise, both with and without furosemide, and 4) a decrease in blood flow to the dorsal region of the lung at rest after furosemide. Pulmonary perfusion variability within the lung may be a function of the anatomy of the pulmonary vessels that results in a predominantly fixed spatial pattern of flow distribution.

Performance Measurement of Advanced Stirling Convertors (ASC-E3)

Science.gov (United States)

Oriti, Salvatore M.

2013-01-01

NASA Glenn Research Center (GRC) has been supporting development of the Advanced Stirling Radioisotope Generator (ASRG) since 2006. A key element of the ASRG project is providing life, reliability, and performance testing data of the Advanced Stirling Convertor (ASC). The latest version of the ASC (ASC-E3, to represent the third cycle of engineering model test hardware) is of a design identical to the forthcoming flight convertors. For this generation of hardware, a joint Sunpower and GRC effort was initiated to improve and standardize the test support hardware. After this effort was completed, the first pair of ASC-E3 units was produced by Sunpower and then delivered to GRC in December 2012. GRC has begun operation of these units. This process included performance verification, which examined the data from various tests to validate the convertor performance to the product specification. Other tests included detailed performance mapping that encompassed the wide range of operating conditions that will exist during a mission. These convertors were then transferred to Lockheed Martin for controller checkout testing. The results of this latest convertor performance verification activity are summarized here.

Evolução do Programa Bolsa Família: Brasil e estados do Nordeste 2004-2009

OpenAIRE

Queiroz, Silvana Nunes de; Remy, Maria Alice Pestana de Aguiar; Pereira, Júlia Modesto Pinheiro Dias; Silva, Luis Abel da

2010-01-01

Este artigo analisa a evolução no número de beneficiários e no valor do repasse do Programa Bolsa Família (PBF). Para tanto, são feitas considerações sobre o conceito de pobreza e as principais alterações na concepção do PBF. O estudo tem como recorte temporal os anos de 2004 a 2009, e recorte espacial o Nordeste brasileiro, região com os piores indicadores sociais e demográficos do país. A fonte de dados foi a Matriz de Informação Social do MDS (Ministério do Desenvolvimento Social), que apo...

Study of a Cherenkov TOF-PET module

Science.gov (United States)

Korpar, S.; Dolenec, R.; Križan, P.; Pestotnik, R.; Stanovnik, A.

2013-12-01

An apparatus, consisting of two PbF2 crystals, each coupled to a multichannel plate photomultiplier (MCP-PMT), has been constructed in order to measure the time-of-flight (TOF) of the two 511 keV annihilation photons produced in positron emission tomography (PET). Excellent timing is achieved by detecting the prompt Cherenkov photons produced by the absorption of the 511 keV gamma photons. The present work describes the measurement and image reconstruction of two 22Na point sources. In addition, the influence of the radiator thickness and the Cherenkov light absorption cut-off of the crystal on the efficiency and the timing resolution have been studied by Monte Carlo simulation.

Comportamiento a tracción de cementos reforzados con fibras de vidrio

Directory of Open Access Journals (Sweden)

Sánchez Paradela, M. Laura

1991-06-01

Full Text Available Glassfibre Reinforced Cement (GRC is a composite material widely used in the field of building construction. It offers multiple applications due to its high strength as well as fire and corrosoón resistance. However, it degradates with time, affecting its mechanical properties, mainly its ductility, becoming progressively brittle and cracking under low deformations. Therefore, with the aim of predicting the mechanical behaviour of the material, both at short time and long time, a wide experimental program has been carried out, testing fresh material as well as aged material. A high number of tensile tests have been performed, using GRC specimens with different kind of fibres and different manufacturing processes for comparison of results. It must be pointed out that it is the first time that tensile tests of GRC specimens have been carried out in Spain.

El cemento reforzado con fibras de vidrio (GRC es un material compuesto que se viene utilizando ampliamente en el campo de la Construcción. Presenta múltiples aplicaciones debido a sus buenas propiedades resistentes y de protección frente al fuego y la corrosión. Sin embargo, sufre un deterioro con el tiempo, que afecta a sus propiedades mecánicas, principalmente a su ductilidad, volviéndose frágil y agrietándose bajo pequeñas deformaciones. Por tal motivo y con el fin de predecir el comportamiento mecánico del material a corto y a largo plazo, se ha desarrollado un extenso programa experimental, empleando tanto material joven como envejecido. Se han realizado numerosos ensayos de tracción directa, utilizando probetas de GRC con diversos tipos de fibras y empleando distintos métodos de fabricación para una comparación de resultados. Es la primera vez que se realizan ensayos de tracción directa en España sobre probetas de GRC.

The flame retardants tetrabromobisphenol A and tetrabromobisphenol A-bisallylether suppress the induction of interleukin-2 receptor α chain (CD25) in murine splenocytes

International Nuclear Information System (INIS)

Pullen, Sabine; Boecker, Ronald; Tiegs, Gisa

2003-01-01

Polybrominated flame retardants (PBF) are frequently used additives in electronical equipment. They are ubiquitous environmental contaminants which bioaccumulate with several health effects for humans and the environment. This study investigated immunotoxic effects of the PBF tetrabromobisphenol A (TBBP A), tetrabromobisphenol A-bisallylether (TBBP A-AE), tetrabromobisphenol A-bis-(2,3-dibromopropyl-ether) (TBBP A-PE), decabromodiphenylether (DBDE), and 2,4,6-tribromophenol (TBP) in vitro. The structurally related polychlorinated aromatic hydrocarbon 3,4,3',4'-tetrachlorobiphenyl (PCB77) and dioxins mediate their immunotoxicity via the Ah-receptor gene complex. A highly relevant function of the Ah receptor, the induction of CYP 1A1 in hepatocytes of C57BL/6 mice by the established inducers 3-methylcholanthrene (MC) and PCB77 was compared to the effect of PBF by measurement of ethoxyresorufin-o-deethylase (EROD) activity. The PBF did not show any induction of CYP 1A1, while EROD activity of hepatocytes exposed to MC and PCB77 was induced 10.8- and 8.7-fold, respectively. To investigate immunotoxic effects of the flame retardants, splenocytes of C57BL/6 mice were incubated with subtoxic doses of the flame retardants and PCB77 and activated by concanavalin A (Con A). The flame retardants TBBP A and TBBP A-AE significantly inhibited the expression of interleukin-2 receptor α chain (CD25) in contrast to TBBP A-PE, DBDE, TBP, and PCB77 as shown by immunohistochemistry and quantitative analysis by laser scanning cytometry. None of the substances had any effect on the Con A-induced production of cytokines. Hence, TBBP A and TBBP A-AE may act as immunotoxic compounds by specifically inhibiting the expression of CD25

The Association Between Men's Concern About Demonstrating Masculine Characteristics and Their Sexual Risk Behaviors: Findings from the Dominican Republic.

Science.gov (United States)

Fleming, Paul J; Barrington, Clare; Powell, Wizdom; Gottert, Ann; Lerebours, Leonel; Donastorg, Yeycy; Brito, Maximo O

2018-02-01

Quantitative analyses exploring the relationship between masculinities and men's sexual risk behaviors have most commonly used one dimension of masculinities: men's gender ideology. Examining other dimensions may enhance our understanding of and ability to intervene upon this relationship. In this article, we examined the association between gender role conflict/stress (GRC/S)-men's concern about demonstrating masculine characteristics-and three different sexual risk behaviors (having two or more sex partners in the last 30 days; never/inconsistent condom use with non-steady partners; and drinking alcohol at last sex) among a sample of heterosexual men in the Dominican Republic who were participating in an HIV prevention intervention (n = 293). The GRC/S Scale we used was adapted for this specific cultural context and has 17 items (α = 0.75). We used logistic regression to assess the relationship between GRC/S and each sexual behavior, controlling for sociodemographic characteristics. In adjusted models, a higher GRC/S score was significantly associated with increased odds of having two or more sex partners in the past 30 days (AOR 1.33, 95 % CI 1.01-1.74), never/inconsistent condom use with non-steady partners (AOR 1.45, 95 % CI 1.04-2.01), and drinking alcohol at last sex (AOR 1.56, 95 % CI 1.13-2.17). These results highlight the importance of expanding beyond gender ideology to understanding the influence of GRC/S on men's sexual risk behaviors. Interventions should address men's concern about demonstrating masculine characteristics to reduce the social and internalized pressure men feel to engage in sexual risk behaviors.

Prospects for first-principle calculations of scintillator properties

International Nuclear Information System (INIS)

Derenzo, Stephen E.; Weber, Marvin J.

1999-01-01

Several scintillation processes can be modeled from first principles using quantum chemistry cluster calculations and recently available high-performance computers. These processes include the formation of excitons and trapping centers, the diffusion of ionization energy (electrons and holes) through a host crystal, and the efficient capture of these carriers by an activator atom to form a luminous, non-quenched excited state. As examples of such calculations, results are presented for (1) hole transport in the known scintillator host crystal CsI, (2) hole trapping in the non-scintillator PbF 2 , (3) hole transport in the experimentally unexplored PbF 4 , and (4) the electronic nature of excited states of CsI : Tl and CsI : Na

Cladodes, leaf-like organs in Asparagus, show the significance of co-option of pre-existing genetic regulatory circuit for morphological diversity of plants.

Science.gov (United States)

Nakayama, Hokuto; Yamaguchi, Takahiro; Tsukaya, Hirokazu

2012-08-01

Plants in the genus Asparagus have determinate leaf-like organs called cladodes in the position of leaf axils. Because of their leaf-like morphology, axillary position, and morphological variation, it has been unclear how this unusual organ has evolved and diversified. In the previous study, we have shown that cladodes in the genus Asparagus are modified axillary shoots and proposed a model that cladodes have arisen by co-option and deployment of genetic regulatory circuit (GRC) involved in leaf development. Moreover, we proposed that the alteration of the expression pattern of genes involved in establishment of adaxial/abaxial polarity has led to the morphological diversification from leaf-like to rod-like form of cladodes in the genus. Thus, these results indicated that the co-option and alteration of pre-existing GRC play an important role in acquisition and subsequent morphological diversification. Here, we present data of further expression analysis of A. asparagoides. The results suggested that only a part of the GRC involved in leaf development appears to have been co-opted into cladode development. Based on our study and several examples of the morphological diversification, we briefly discuss the importance of co-option of pre-existing GRC and its genetic modularity in the morphological diversity of plants during evolution.

Learning From Experience

DEFF Research Database (Denmark)

Visholm, Steen; Beck, Ulla Charlotte

2014-01-01

University and NAPSO2). Seen from the horizon of their experience some of the basic concepts in the theories about GRC need clarifying, revision, and development. The GRC is a part of the learning from experience movement and as a consequence it stresses the underlying basis: learning is personal so everyone...... presented and discussed and two later contributions are presented: Barry Palmer's theory (Palmer, 1979) and Junell Silver and Ruthellen Josselson's study (Silver & Josselson, 2010). The learning concepts of the GRCs are found to be too general and too far from organisational life. As an attempt to move......In this paper the learning concept of group relation's conferences are discussed. The authors have worked with group relations conferences (GRC) in different contexts for many years-mainly as a part of educational programmes for managers and consultants (OPU at IGA Copenhagen, MPO at Roskilde...

Distributed gas sensing with optical fibre photothermal interferometry.

Science.gov (United States)

Lin, Yuechuan; Liu, Fei; He, Xiangge; Jin, Wei; Zhang, Min; Yang, Fan; Ho, Hoi Lut; Tan, Yanzhen; Gu, Lijuan

2017-12-11

We report the first distributed optical fibre trace-gas detection system based on photothermal interferometry (PTI) in a hollow-core photonic bandgap fibre (HC-PBF). Absorption of a modulated pump propagating in the gas-filled HC-PBF generates distributed phase modulation along the fibre, which is detected by a dual-pulse heterodyne phase-sensitive optical time-domain reflectometry (OTDR) system. Quasi-distributed sensing experiment with two 28-meter-long HC-PBF sensing sections connected by single-mode transmission fibres demonstrated a limit of detection (LOD) of ∼10 ppb acetylene with a pump power level of 55 mW and an effective noise bandwidth (ENBW) of 0.01 Hz, corresponding to a normalized detection limit of 5.5ppb⋅W/Hz. Distributed sensing experiment over a 200-meter-long sensing cable made of serially connected HC-PBFs demonstrated a LOD of ∼ 5 ppm with 62.5 mW peak pump power and 11.8 Hz ENBW, or a normalized detection limit of 312ppb⋅W/Hz. The spatial resolution of the current distributed detection system is limited to ∼ 30 m, but it is possible to reduce down to 1 meter or smaller by optimizing the phase detection system.

Validation of Patient-Reported Outcomes Measurement Information System Short Forms for Use in Childhood-Onset Systemic Lupus Erythematosus.

Science.gov (United States)

Jones, Jordan T; Carle, Adam C; Wootton, Janet; Liberio, Brianna; Lee, Jiha; Schanberg, Laura E; Ying, Jun; Morgan DeWitt, Esi; Brunner, Hermine I

2017-01-01

To validate the pediatric Patient-Reported Outcomes Measurement Information System short forms (PROMIS-SFs) in childhood-onset systemic lupus erythematosus (SLE) in a clinical setting. At 3 study visits, childhood-onset SLE patients completed the PROMIS-SFs (anger, anxiety, depressive symptoms, fatigue, physical function-mobility, physical function-upper extremity, pain interference, and peer relationships) using the PROMIS assessment center, and health-related quality of life (HRQoL) legacy measures (Pediatric Quality of Life Inventory, Childhood Health Assessment Questionnaire, Simple Measure of Impact of Lupus Erythematosus in Youngsters [SMILEY], and visual analog scales [VAS] of pain and well-being). Physicians rated childhood-onset SLE activity on a VAS and completed the Systemic Lupus Erythematosus Disease Activity Index 2000. Using a global rating scale of change (GRC) between study visits, physicians rated change of childhood-onset SLE activity (GRC-MD1: better/same/worse) and change of patient overall health (GRC-MD2: better/same/worse). Questionnaire scores were compared in support of validity and responsiveness to change (external standards: GRC-MD1, GRC-MD2). In this population-based cohort (n = 100) with a mean age of 15.8 years (range 10-20 years), the PROMIS-SFs were completed in less than 5 minutes in a clinical setting. The PROMIS-SF scores correlated at least moderately (Pearson's r ≥ 0.5) with those of legacy HRQoL measures, except for the SMILEY. Measures of childhood-onset SLE activity did not correlate with the PROMIS-SFs. Responsiveness to change of the PROMIS-SFs was supported by path, mixed-model, and correlation analyses. To assess HRQoL in childhood-onset SLE, the PROMIS-SFs demonstrated feasibility, internal consistency, construct validity, and responsiveness to change in a clinical setting. © 2016, American College of Rheumatology.

Electromagnetic calorimetry with lead fluoride crystals

International Nuclear Information System (INIS)

Appuhn, R.D.; Korbel, V.; Meier, K.; Valkar, S.

1993-10-01

The properties of four PbF 2 crystals of size 21.21.175 mm 3 were studied with electron and pion beams in the energy range from 1 to 6 GeV. An energy resolution for electrons of 6.3%/√(E/GeV) was achieved with a 2x2 matrix of four PbF 2 crystals, which corresponds to 5.6%/√(E/GeV) when corrected for lateral leakage by Monte Carlo simulations. The deviation from linearity was smaller than 0.5%. The time resolution was found to be better than 0.6 ns. We studied also optical properties, radiation hardness, position resolution and spatial homogeneity. An efficient separation of electromagnetic and hadronic showers was achieved. (orig.)

Comparison of the cladding deformation measured during the Power Burst Facility loss-of-coolant accident in-pile experiments with recent Oak Ridge National Laboratory out-of-pile results

International Nuclear Information System (INIS)

Broughton, J.M.; McCardell, R.K.; MacDonald, P.E.

1981-01-01

A series of four large break loss-of-coolant accident fuel behavior experiments have been performed in the Power Burst Facility. The results of these experiments are briefly reviewed and compared with results from the ORNL multirod burst test program. The effect of cladding burst temperature and prior irradiation were investigated. The cladding strain of the previously irradiated test rods was more uniformly distributed around the cladding circumference and larger than for similar unirradiated test rods. The ORNL out-of-pile single rod test results are in good agreement with the Power Burst Facility (PBF) test results with unirradiated test rods, and the ORNL out-of-pile, single-rod test results with heated shrouds and the PBF test results with previously irradiated test rods are comparable

Control and Non-Payload Communications (CNPC) Prototype Radio - Generation 2 Security Flight Test Report

Science.gov (United States)

Iannicca, Dennis C.; Ishac, Joseph A.; Shalkhauser, Kurt A.

2015-01-01

NASA Glenn Research Center (GRC), in cooperation with Rockwell Collins, is working to develop a prototype Control and Non-Payload Communications (CNPC) radio platform as part of NASA Integrated Systems Research Program's (ISRP) Unmanned Aircraft Systems (UAS) Integration in the National Airspace System (NAS) project. A primary focus of the project is to work with the Federal Aviation Administration (FAA) and industry standards bodies to build and demonstrate a safe, secure, and efficient CNPC architecture that can be used by industry to evaluate the feasibility of deploying a system using these technologies in an operational capacity. GRC has been working in conjunction with these groups to assess threats, identify security requirements, and to develop a system of standards-based security controls that can be applied to the GRC prototype CNPC architecture as a demonstration platform. The proposed security controls were integrated into the GRC flight test system aboard our S-3B Viking surrogate aircraft and several network tests were conducted during a flight on November 15th, 2014 to determine whether the controls were working properly within the flight environment. The flight test was also the first to integrate Robust Header Compression (ROHC) as a means of reducing the additional overhead introduced by the security controls and Mobile IPv6. The effort demonstrated the complete end-to-end secure CNPC link in a relevant flight environment.

Extended Operation of Stirling Convertors at NASA Glenn Research Center

Science.gov (United States)

Oriti, Salvatore, M.

2012-01-01

NASA Glenn Research Center (GRC) has been supporting development of free-piston Stirling conversion technology for spaceflight electrical power generation since 1999. GRC has also been supporting the development of the Advanced Stirling Radioisotope Generator (ASRG) since 2006. A key element of the ASRG project is providing life, reliability, and performance data for the Advanced Stirling Convertor (ASC). The Thermal Energy Conversion branch at GRC is conducting extended operation of several free-piston Stirling convertors. The goal of this effort is to generate long-term performance data (tens of thousands of hours) on multiple units to build a life and reliability database. Currently, GRC is operating 18 convertors. This hardware set includes Technology Demonstration Convertors (TDCs) from Infinia Corporation, of which one pair (TDCs #13 and #14) has accumulated over 60,000 hr (6.8 years) of operation. Also under test are various Sunpower, Inc. convertors that were fabricated during the ASC development activity, including ASC-0, ASC-E (including those in the ASRG engineering unit), and ASC-E2. The ASC-E2s also completed, or are in progress of completing workmanship vibration testing, performance mapping, and extended operation. Two ASC-E2 units will also be used for durability testing, during which components will be stressed to levels above nominal mission usage. Extended operation data analyses from these tests are covered in this paper.

Upgrade of the JET gamma-ray cameras

International Nuclear Information System (INIS)

Soare, S.; Curuia, M.; Anghel, M.; Constantin, M.; David, E.; Craciunescu, T.; Falie, D.; Pantea, A.; Tiseanu, I.; Kiptily, V.; Prior, P.; Edlington, T.; Griph, S.; Krivchenkov, Y.; Loughlin, M.; Popovichev, S.; Riccardo, V; Syme, B.; Thompson, V.; Lengar, I.; Murari, A.; Bonheure, G.; Le Guern, F.

2007-01-01

Full text: The JET gamma-ray camera diagnostics have already provided valuable information on the gamma-ray imaging of fast ion in JET plasmas. The applicability of gamma-ray imaging to high performance deuterium and deuterium-tritium JET discharges is strongly dependent on the fulfilment of rather strict requirements for the characterisation of the neutron and gamma-ray radiation fields. These requirements have to be satisfied within very stringent boundary conditions for the design, such as the requirement of minimum impact on the co-existing neutron camera diagnostics. The JET Gamma-Ray Cameras (GRC) upgrade project deals with these issues with particular emphasis on the design of appropriate neutron/gamma-ray filters ('neutron attenuators'). Several design versions have been developed and evaluated for the JET GRC neutron attenuators at the conceptual design level. The main design parameter was the neutron attenuation factor. The two design solutions, that have been finally chosen and developed at the level of scheme design, consist of: a) one quasi-crescent shaped neutron attenuator (for the horizontal camera) and b) two quasi-trapezoid shaped neutron attenuators (for the vertical one). The second design solution has different attenuation lengths: a short version, to be used together with the horizontal attenuator for deuterium discharges, and a long version to be used for high performance deuterium and DT discharges. Various neutron-attenuating materials have been considered (lithium hydride with natural isotopic composition and 6 Li enriched, light and heavy water, polyethylene). Pure light water was finally chosen as the attenuating material for the JET gamma-ray cameras. The neutron attenuators will be steered in and out of the detector line-of-sight by means of an electro-pneumatic steering and control system. The MCNP code was used for neutron and gamma ray transport in order to evaluate the effect of the neutron attenuators on the neutron field of the

In Situ 3D Monitoring of Geometric Signatures in the Powder-Bed-Fusion Additive Manufacturing Process via Vision Sensing Methods.

Science.gov (United States)

Li, Zhongwei; Liu, Xingjian; Wen, Shifeng; He, Piyao; Zhong, Kai; Wei, Qingsong; Shi, Yusheng; Liu, Sheng

2018-04-12

Lack of monitoring of the in situ process signatures is one of the challenges that has been restricting the improvement of Powder-Bed-Fusion Additive Manufacturing (PBF AM). Among various process signatures.

2016 Microbial Stress Response GRC/GRS

Science.gov (United States)

2016-09-13

Communicate to Regulate Antimicrobial Peptide Resistance in Gram Positive Bacteria" 10:35 am - 10:40 am Discussion 10:40 am - 11:05 am Coffee Break 11...San Diego State University, USA) "A Tail of Phage and Tubeworms: How Do Bacteria Stimulate Animal Development?" 12:05 pm - 12:15 pm Discussion 12...Transcription Conflict in Bacteria" 9:20 pm - 9:30 pm Discussion Wednesday 7:30 am - 8:30 am Breakfast 9:00 am - 12:30 pm Genetic and Phenotypic Resistance

Stirling Technology Development at NASA GRC

Science.gov (United States)

Thieme, Lanny G.; Schreiber, Jeffrey G.; Mason, Lee S.

2001-01-01

The Department of Energy, Stirling Technology Company (STC), and NASA Glenn Research Center (NASA Glenn) are developing a free-piston Stirling convertor for a high efficiency Stirling Radioisotope Generator (SRG) for NASA Space Science missions. The SRG is being developed for multimission use, including providing electric power for unmanned Mars rovers and deep space missions. NASA Glenn is conducting an in-house technology project to assist in developing the convertor for space qualification and mission implementation. Recent testing of 55-We Technology Demonstration Convertors (TDCs) built by STC includes mapping of a second pair of TDCs, single TDC testing, and TDC electromagnetic interference and electromagnetic compatibility characterization on a nonmagnetic test stand. Launch environment tests of a single TDC without its pressure vessel to better understand the convertor internal structural dynamics and of dual-opposed TDCs with several engineering mounting structures with different natural frequencies have recently been completed. A preliminary life assessment has been completed for the TDC heater head, and creep testing of the IN718 material to be used for the flight convertors is underway. Long-term magnet aging tests are continuing to characterize any potential aging in the strength or demagnetization resistance of the magnets used in the linear alternator (LA). Evaluations are now beginning on key organic materials used in the LA and piston/rod surface coatings. NASA Glenn is also conducting finite element analyses for the LA, in part to look at the demagnetization margin on the permanent magnets. The world's first known integrated test of a dynamic power system with electric propulsion was achieved at NASA Glenn when a Hall-effect thruster was successfully operated with a free-piston Stirling power source. Cleveland State University is developing a multidimensional Stirling computational fluid dynamics code to significantly improve Stirling loss predictions and assist in identifying convertor areas for further improvements. This paper will update the status and results for these efforts.

Qualifications manual for Inspection and Enforcement personnel. Volume I. Detailed data sheets

International Nuclear Information System (INIS)

Bartley, H.J.; Heyer, F.H.K.; Schwartz, E.G.; Harrison, O.J.; Krass, I.W.; Welsh, D.M.

1978-06-01

This document is the General Research Corporation (GRC) final report on Task I Job/Position Qualifications Statements for the Headquarters and regional position of NRC/IE. It reflects the results of upgrading, expanding, and reformating the preliminary Task I report. To accomplish this, GRC made a thorough examination of all data developed during Task I, Task II (Career Fields), Task III (Training Evaluation), and Task IV (Hiring Qualifications), to include NRC/IE comments and management decisions received. The reformated Job/Position Qualifications Statements resulting from this effort (Appendix A) identify three job qualifications categories for each position--performance, attributes, and knowledge. Two formats are provided: a summarized one for manpower management in Volume I and a detailed one for career and training management in Volume II. In addition to recommending approval of the job/position qualifications, GRC proposes their use in conjunction with the hiring qualifications in the Task IV report to update NRC/IE job descriptions

Gearbox Reliability Collaborative Gearbox 1 Failure Analysis Report: December 2010 - January 2011

Energy Technology Data Exchange (ETDEWEB)

Errichello, R.; Muller, J.

2012-02-01

Unintended gearbox failures have a significant impact on the cost of wind farm operations. In 2007, NREL initiated the Gearbox Reliability Collaborative (GRC). The project combines analysis, field testing, dynamometer testing, condition monitoring, and the development and population of a gearbox failure database in a multi-pronged approach to determine why wind turbine gearboxes do not achieve their expected design life. The collaborative of manufacturers, owners, researchers, and consultants focuses on gearbox testing and modeling and the development of a gearbox failure database. Collaborative members also investigate gearbox condition monitoring techniques. Data gained from the GRC will enable designers, developers, and manufacturers to improve gearbox designs and testing standards and create more robust modeling tools. GRC project essentials include the development of two identical, heavily instrumented representative gearbox designs. Knowledge gained from the field and dynamometer tests conducted on these gearboxes builds an understanding of how the selected loads and events translate into bearing and gear response. This report contains the analysis of the first gearbox design.

Comparison of percentage body fat and body mass index for the prediction of inflammatory and atherogenic lipid risk profiles in elderly women.

Science.gov (United States)

Funghetto, Silvana Schwerz; Silva, Alessandro de Oliveira; de Sousa, Nuno Manuel Frade; Stival, Marina Morato; Tibana, Ramires Alsamir; Pereira, Leonardo Costa; Antunes, Marja Letícia Chaves; de Lima, Luciano Ramos; Prestes, Jonato; Oliveira, Ricardo Jacó; Dutra, Maurílio Tiradentes; Souza, Vinícius Carolino; Nascimento, Dahan da Cunha; Karnikowski, Margô Gomes de Oliveira

2015-01-01

To compare the clinical classification of the body mass index (BMI) and percentage body fat (PBF) for the prediction of inflammatory and atherogenic lipid profile risk in older women. Cross-sectional analytical study with 277 elderly women from a local community in the Federal District, Brazil. PBF and fat-free mass (FFM) were determined by dual energy X-ray absorptiometry. The investigated inflammatory parameters were interleukin 6 and C-reactive protein. Twenty-five percent of the elderly women were classified as normal weight, 50% overweight, and 25% obese by the BMI. The obese group had higher levels of triglycerides and very low-density lipoproteins than did the normal weight group (P≤0.05) and lower levels of high-density lipoproteins (HDL) than did the overweight group (P≤0.05). According to the PBF, 49% of the elderly women were classified as eutrophic, 28% overweight, and 23% obese. In the binomial logistic regression analyses including age, FFM, and lipid profile, only FFM (odds ratio [OR]=0.809, 95% confidence interval [CI]: 0.739-0.886; Pprofile is key to assessing the risk of cardiometabolic diseases. Classification based on dual energy X-ray absorptiometry measures, along with biochemical and inflammatory parameters, seems to have a great clinical importance, since it allows the lipid profile eutrophic distinction in elderly overweight women.

Avaliação do uso de glyphosate em soja geneticamente modificada e sua relação com o ácido chiquímico Evaluation of glyphosate application on transgenic soybean and its relationship with shikimic acid

Directory of Open Access Journals (Sweden)

D.A.S. Franco

2012-09-01

plantas de soja transgênica no campo quando tratadas de forma isolada com glyphosate. Os resultados também mostraram exsudação radicular do glyphosate por soja transgênica, com posterior absorção por soja convencional. Foram detectados resíduos de glyphosate e ácido aminometilfosfônico na solução nutritiva.Glyphosate [N-(phosphonomethyl glycine]-resistant crops (GRC are the transgenic crops most extensively grown worldwide, with soybean being the major GRC. It is important to evaluate the impact of glyphosate on transgenic soybean and its relationship with shikimic acid. A field experiment was conducted at Engenheiro Coelho-SP, Brazil, during the agricultural year 2007/2008 to evaluate the effect of glyphosate on the growth, development, and seed quality of GRC soybean variety BRS Valiosa RR. A randomized block design was used with four replications. Glyphosate was applied at 720 and 960 g a.e. ha-1 (acid equivalent and in sequence at the doses 720/720, 960/720, and 960/720/720 g a.e. ha-1 (acid equivalent. To evaluate transfer from GRC soybean to non GRC soybean cultivated in nutrient solution, a pot experiment was conducted at Instituto Biológico, SP, Brazil. Glyphosate was applied on the GRC soybean (M8045RR at 2,400 g a.e. ha-1. Both GRC soybean and non GRC soybean were sown in the same box with nutrient solution. At 0, 1, 3, 7, and 10 days after application, shikimic acid was measured by HPLC and the glyphosate and aminomethylphosphonic acid (AMPA levels in nutrient solution were determined by GC-MS. The results showed that yield, plant height, seed oil, and protein contents were not affected by glyphosate application. GRC soybean accumulated shikimic acid in the field. Glyphosate and AMPA were released through the roots of GRC soybean, and subsequently taken up by non-GRC soybean, exerting inhibitory effects on their shikimic pathway.

Power Burst Facility/Boron Neutron Capture Therapy Program for cancer treatment

Energy Technology Data Exchange (ETDEWEB)

Ackermann, A.L. (ed.); Dorn, R.V. III.

1990-09-01

This monthly bulletin describes activities in the following project areas during this reporting period: supporting technology development, large animal model studies, neutron source and facility preparation, administration and common support, and PBF operations. (FI)

Power Burst Facility/Boron Neutron Capture Therapy Program for cancer treatment

Energy Technology Data Exchange (ETDEWEB)

Ackermann, A.L. (ed.)

1990-10-01

This bulletin discusses activities during this reporting period in the areas of: supporting technology development; large animal model studies; melanoma project; human studies; stability, pharmacology, and toxicology of drugs; and PBF technical support. (FL)

O Impacto das Regras do Programa Bolsa Família Sobre a Fecundidade das Beneficiárias

Directory of Open Access Journals (Sweden)

Luis Antonio Winck Cechin

2015-09-01

Full Text Available Este trabalho investiga um possível incentivo do Programa Bolsa Família ao aumento da fecundidade de suas beneficiárias em decorrência de suas regras, dado que a quantidade de recursos transferidos depende do número de filhos da família. O diferencial deste estudo reside na análise desse impacto em um maior período de exposição das beneficiárias aos efeitos do PBF. Aplica-se o algoritmo de seleção de covariadas proposto por Imbens (2014 e o método de Propensity Score Matching. Os resultados apontaram que o PBF gera pequeno incentivo à geração do segundo filho, sendo que as regiões Centro-Oeste e Nordeste apresentaram os maiores valores de impacto.

Morphological Constraints on Cerebellar Granule Cell Combinatorial Diversity.

Science.gov (United States)

Gilmer, Jesse I; Person, Abigail L

2017-12-13

Combinatorial expansion by the cerebellar granule cell layer (GCL) is fundamental to theories of cerebellar contributions to motor control and learning. Granule cells (GrCs) sample approximately four mossy fiber inputs and are thought to form a combinatorial code useful for pattern separation and learning. We constructed a spatially realistic model of the cerebellar GCL and examined how GCL architecture contributes to GrC combinatorial diversity. We found that GrC combinatorial diversity saturates quickly as mossy fiber input diversity increases, and that this saturation is in part a consequence of short dendrites, which limit access to diverse inputs and favor dense sampling of local inputs. This local sampling also produced GrCs that were combinatorially redundant, even when input diversity was extremely high. In addition, we found that mossy fiber clustering, which is a common anatomical pattern, also led to increased redundancy of GrC input combinations. We related this redundancy to hypothesized roles of temporal expansion of GrC information encoding in service of learned timing, and we show that GCL architecture produces GrC populations that support both temporal and combinatorial expansion. Finally, we used novel anatomical measurements from mice of either sex to inform modeling of sparse and filopodia-bearing mossy fibers, finding that these circuit features uniquely contribute to enhancing GrC diversification and redundancy. Our results complement information theoretic studies of granule layer structure and provide insight into the contributions of granule layer anatomical features to afferent mixing. SIGNIFICANCE STATEMENT Cerebellar granule cells are among the simplest neurons, with tiny somata and, on average, just four dendrites. These characteristics, along with their dense organization, inspired influential theoretical work on the granule cell layer as a combinatorial expander, where each granule cell represents a unique combination of inputs

Influence of the Bolsa Família program on nutritional status and food frequency of schoolchildren

Directory of Open Access Journals (Sweden)

Ariene Silva do Carmo

2016-07-01

Full Text Available Objective: To evaluate the food frequency and nutritional status among students according to participation in the Bolsa Família program funded by the government. Methods: Cross-sectional study carried out with students from the fourth grade of elementary school in the municipal capital of the southeastern region of Brazil. Food consumption and anthropometry were investigated by a questionnaire administered in school, while participation in the Bolsa Família program and other socio-economic information was obtained through a protocol applied to mothers/guardians. Statistical analysis included the Mann–Whitney test, the chi-squared test, and Poisson regression with robust variance, and the 5% significance level was adopted. Results: There were 319 children evaluated; 56.4% were male, with a median of 9.4 (8.6–11.9 years, and 37.0% were beneficiaries of Bolsa Família program. Between the two groups, there was high prevalence of regular soda consumption (34.3%, artificial juice (49.5%, and sweets (40.3%, while only 54.3% and 51.7% consumed fruits and vegetables regularly, respectively. Among participants of Bolsa Família program, a prevalence 1.24 times higher in the regular consumption of soft drinks (95% CI: 1.10–1.39 was identified compared to non-beneficiaries. The prevalence of overweight was higher in the sample (32.9%, with no difference according to participation in the program. Conclusion: The study found increased consumption of soft drinks among BFP participants. The high rate of overweight and poor eating habits denote the need to develop actions to promote healthy eating, especially for the beneficiaries of the Bolsa Família program, to promote improvements in nutritional status and prevent chronic diseases throughout life. Resumo: Objetivo: Avaliar a frequência alimentar e estado nutricional entre escolares segundo a participação no programa governamental Bolsa Família (PBF. Metodologia: Estudo de delineamento

Test Rack Development for Extended Operation of Advanced Stirling Convertors at NASA Glenn Research Center

Science.gov (United States)

Dugala, Gina M.

2010-01-01

The U.S. Department of Energy, Lockheed Martin Space Systems Company, Sunpower Inc., and NASA Glenn Research Center (GRC) have been developing an Advanced Stirling Radioisotope Generator (ASRG) for use as a power system on space science missions. This generator will make use of free-piston Stirling convertors to achieve higher conversion efficiency than with currently available alternatives. One part of NASA GRC's support of ASRG development includes extended operation testing of Advanced Stirling Convertors (ASCs) developed by Sunpower Inc. and GRC. The ASC consists of a free-piston Stirling engine integrated with a linear alternator. NASA GRC has been building test facilities to support extended operation of the ASCs for several years. Operation of the convertors in the test facility provides convertor performance data over an extended period of time. One part of the test facility is the test rack, which provides a means for data collection, convertor control, and safe operation. Over the years, the test rack requirements have changed. The initial ASC test rack utilized an alternating-current (AC) bus for convertor control; the ASRG Engineering Unit (EU) test rack can operate with AC bus control or with an ASC Control Unit (ACU). A new test rack is being developed to support extended operation of the ASC-E2s with higher standards of documentation, component selection, and assembly practices. This paper discusses the differences among the ASC, ASRG EU, and ASC-E2 test racks.

Development and Testing of a Prototype Grid-Tied Photovoltaic Power System

Science.gov (United States)

Eichenberg, Dennis J.

2009-01-01

The NASA Glenn Research Center (GRC) has developed and tested a prototype 2 kW DC grid-tied photovoltaic (PV) power system at the Center. The PV system has generated in excess of 6700 kWh since operation commenced in July 2006. The PV system is providing power to the GRC grid for use by all. Operation of the prototype PV system has been completely trouble free. A grid-tied PV power system is connected directly to the utility distribution grid. Facility power can be obtained from the utility system as normal. The PV system is synchronized with the utility system to provide power for the facility, and excess power is provided to the utility. The project transfers space technology to terrestrial use via nontraditional partners. GRC personnel glean valuable experience with PV power systems that are directly applicable to various space power systems, and provide valuable space program test data. PV power systems help to reduce harmful emissions and reduce the Nation s dependence on fossil fuels. Power generated by the PV system reduces the GRC utility demand, and the surplus power aids the community. Present global energy concerns reinforce the need for the development of alternative energy systems. Modern PV panels are readily available, reliable, efficient, and economical with a life expectancy of at least 25 years. Modern electronics has been the enabling technology behind grid-tied power systems, making them safe, reliable, efficient, and economical with a life expectancy of at least 25 years. Based upon the success of the prototype PV system, additional PV power system expansion at GRC is under consideration. The prototype grid-tied PV power system was successfully designed and developed which served to validate the basic principles described, and the theoretical work that was performed. The report concludes that grid-tied photovoltaic power systems are reliable, maintenance free, long life power systems, and are of significant value to NASA and the community.

households' choices of healthcare services in the north west region

African Journals Online (AJOL)

model. Households' characteristics such as sex and age of household heads, marital status of household heads and .... Based Financing (PBF) of healthcare in the North .... return from this capital in both market and non- ... Healthy Life Style.

Physics and chemistry of an ionic liquid in some industrially important solvent media probed by physicochemical techniques

International Nuclear Information System (INIS)

Roy, Mahendra Nath; Banik, Ishani; Ekka, Deepak

2013-01-01

Highlights: ► Molecular interaction of Bu 4 PBF 4 in DMSO, DMA, and DMF has been studied. ► More ion–solvent interaction between Bu 4 PBF 4 and DMSO. ► Ion–solvent interaction dominate over ion–ion interaction in the studied solutions. - Abstract: Electrolytic conductivities (Λ), densities (ρ), viscosities (η), and ultrasonic speed (u) of an ionic liquid (IL) tetrabutylphosphonium tetrafluoroborate [Bu 4 PBF 4 ] have been studied in dimethylsulfoxide (DMSO), dimethylacetamide (DMA), and dimethylformamide (DMF) at T = 298.15 K. The limiting molar conductivity (Λ 0 ), the association constant (K A ), and the distance of closest approach of ions (R) have been evaluated using the Fuoss conductance equation (1978). The molar conductivities observed were explained by the formation of ion-pairs (M + + X − ↔ MX). The Walden product is obtained and discussed. Ion–solvent interactions have been interpreted in terms of apparent molar volumes (φ V ) and viscosity B-coefficients which are obtained from the results supplemented with densities and viscosities, respectively. The limiting apparent molar volumes (φ V 0 ), experimental slopes (S V ∗ ) derived from the Masson equation and viscosity A and B coefficients using the Jones–Dole equation have been interpreted in terms of ion–ion and ion–solvent interactions respectively. The adiabatic compressibility (β) has been evaluated using the ultrasonic speed (u) values. Finally values of the limiting partial molar adiabatic compressibility (φ K 0 ) are calculated and discussed.

Measurement and validation of measures for impulsive food choice across obese and healthy-weight individuals.

Science.gov (United States)

Hendrickson, Kelsie L; Rasmussen, Erin B; Lawyer, Steven R

2015-07-01

The present study established a brief measure of delay discounting for food, the Food Choice Questionnaire (FCQ), and compared it to another more established measure of food discounting that uses the adjusting amount (AA) procedure. One hundred forty-four undergraduate participants completed either two measures of hypothetical food discounting (a computerized food AA procedure or the FCQ) or two measures of hypothetical money discounting [a computerized monetary AA procedure or the Monetary Choice questionnaire (MCQ)]. The money condition was used as a replication of previous work. Results indicated that the FCQ yielded consistent data that strongly correlated with the AA food discounting task. Moreover, a magnitude effect was found with the FCQ, such that smaller amounts of food were discounted more steeply than larger amounts. In addition, individuals with higher percent body fat (PBF) discounted food more steeply than individuals with lower PBF. The MCQ, which also produced a magnitude effect, and the monetary adjusting amount procedure yielded data that were orderly, consistent, and correlated strongly with one another, replicating previous literature. This study is the first to show that a novel measure of food discounting (the FCQ) yields consistent data strongly correlated with an established measure of food discounting and is sensitive to PBF. Moreover, the FCQ is easier and quicker to administer than the AA procedure, which may interest researchers who use discounting tasks in food-related research. Copyright © 2015 Elsevier Ltd. All rights reserved.

Luminescent features of sol–gel derived rare-earth multi-doped oxyfluoride nano-structured phosphors for white LED application

International Nuclear Information System (INIS)

Gouveia-Neto, A.S.; Silva, A.F. da; Bueno, L.A.; Costa, E.B. da

2012-01-01

Rare-earth doped oxyfluoride 75SiO 2 :25PbF 2 nano-structured phosphors for white-light-emitting diodes were synthesized by thermal treatment of precursor sol–gel derived glasses. Room temperature luminescence features of Eu 3+ , Sm 3+ , Tb 3+ , Eu 3+ /Tb 3+ , and Sm 3+ /Tb 3+ ions incorporated into low-phonon-energy PbF 2 nanocrystals dispersed in the aluminosilicate glass matrix and excited with UV light emitting diode were investigated. The luminescence spectra exhibited strong emission signals in the red (600, 610, 625, and 646 nm), green (548 and 560 nm), and blue (485 nm) wavelength regions. White-light emission was observed in Sm/Tb and Eu/Tb double-doped activated phosphors employing UV-LED excitation at 395 nm. The dependence of the luminescence emission intensities upon annealing temperature and rare-earth concentration was also examined. The results indicated that there exist optimum annealing temperature and activator ion concentration in order to obtain intense visible emission light with high color rendering index. The study suggests that the nanocomposite phosphor based upon 75SiO 2 :25PbF 2 host herein reported is a promising contender for white-light LED applications. - Highlights: ► White-light emission in double-doped activated phosphors employing UV-LED excitation. ► Luminescent features of europium, samarium, and terbium in nanocrystals dispersed in aluminosilicate glass. ► New nanocomposite phosphor host for white-light LED applications.

Measuring Men's Gender Norms and Gender Role Conflict/Stress in a High HIV-Prevalence South African Setting.

Science.gov (United States)

Gottert, Ann; Barrington, Clare; Pettifor, Audrey; McNaughton-Reyes, Heath Luz; Maman, Suzanne; MacPhail, Catherine; Kahn, Kathleen; Selin, Amanda; Twine, Rhian; Lippman, Sheri A

2016-08-01

Gender norms and gender role conflict/stress may influence HIV risk behaviors among men; however scales measuring these constructs need further development and evaluation in African settings. We conducted exploratory and confirmatory factor analyses to evaluate the Gender Equitable Men's Scale (GEMS) and the Gender Role Conflict/Stress (GRC/S) scale among 581 men in rural northeast South Africa. The final 17-item GEMS was unidimensional, with adequate model fit and reliability (alpha = 0.79). Factor loadings were low (0.2-0.3) for items related to violence and sexual relationships. The final 24-item GRC/S scale was multidimensional with four factors: Success, power, competition; Subordination to women; Restrictive emotionality; and Sexual prowess. The scale had adequate model fit and good reliability (alpha = 0.83). While GEMS is a good measure of inequitable gender norms, new or revised scale items may need to be explored in the South African context. Adding the GRC/S scale to capture men's strain related to gender roles could provide important insights into men's risk behaviors.

Overview of Multi-Kilowatt Free-Piston Stirling Power Conversion Research at Glenn Research Center

Science.gov (United States)

Geng, Steven M.; Mason, Lee S.; Dyson, Rodger W.; Penswick, L. Barry

2008-01-01

As a step towards development of Stirling power conversion for potential use in Fission Surface Power (FSP) systems, a pair of commercially available 1 kW class free-piston Stirling convertors and a pair of commercially available pressure wave generators (which will be plumbed together to create a high power Stirling linear alternator test rig) have been procured for in-house testing at Glenn Research Center (GRC). Delivery of both the Stirling convertors and the linear alternator test rig is expected by October 2007. The 1 kW class free-piston Stirling convertors will be tested at GRC to map and verify performance. The convertors will later be modified to operate with a NaK liquid metal pumped loop for thermal energy input. The high power linear alternator test rig will be used to map and verify high power Stirling linear alternator performance and to develop power management and distribution (PMAD) methods and techniques. This paper provides an overview of the multi-kilowatt free-piston Stirling power conversion work being performed at GRC.

Fuel-rod response during the large-break LOCA Test LOC-6

International Nuclear Information System (INIS)

Vinjamuri, K.; Cook, B.A.; Hobbins, R.R.

1981-01-01

The large break Loss of Coolant Accident (LOCA) Test LOC-6 was conducted in the Power Burst Facility (PBF) at the Idaho National Engineering Laboratory by EG and G Idaho, Inc. The objectives of the PBF LOCA tests are to obtain in-pile cladding ballooning data under blowdown and reflood conditions and assess how well out-of-pile ballooning data represent in-pile fuel rod behavior. The primary objective of the LOC-6 test was to determine the effects of internal rod pressures and prior irradiation on the deformation behavior of fuel rods that reached cladding temperatures high in the alpha phase of zircaloy. Test LOC-6 was conducted with four rods of PWR 15 x 15 design with the exception of fuel stack length (89 cm) and enrichment (12.5 W% 235 U). Each rod was surrounded by an individual flow shroud

Residual stress measurements via neutron diffraction of additive manufactured stainless steel 17-4 PH.

Science.gov (United States)

Masoomi, Mohammad; Shamsaei, Nima; Winholtz, Robert A; Milner, Justin L; Gnäupel-Herold, Thomas; Elwany, Alaa; Mahmoudi, Mohamad; Thompson, Scott M

2017-08-01

Neutron diffraction was employed to measure internal residual stresses at various locations along stainless steel (SS) 17-4 PH specimens additively manufactured via laser-powder bed fusion (L-PBF). Of these specimens, two were rods (diameter=8 mm, length=80 mm) built vertically upward and one a parallelepiped (8×80×9 mm 3 ) built with its longest edge parallel to ground. One rod and the parallelepiped were left in their as-built condition, while the other rod was heat treated. Data presented provide insight into the microstructural characteristics of typical L-PBF SS 17-4 PH specimens and their dependence on build orientation and post-processing procedures such as heat treatment. Data have been deposited in the Data in Brief Dataverse repository (doi:10.7910/DVN/T41S3V).

Residual stress measurements via neutron diffraction of additive manufactured stainless steel 17-4 PH

Directory of Open Access Journals (Sweden)

Mohammad Masoomi

2017-08-01

Full Text Available Neutron diffraction was employed to measure internal residual stresses at various locations along stainless steel (SS 17-4 PH specimens additively manufactured via laser-powder bed fusion (L-PBF. Of these specimens, two were rods (diameter=8 mm, length=80 mm built vertically upward and one a parallelepiped (8×80×9 mm3 built with its longest edge parallel to ground. One rod and the parallelepiped were left in their as-built condition, while the other rod was heat treated. Data presented provide insight into the microstructural characteristics of typical L-PBF SS 17-4 PH specimens and their dependence on build orientation and post-processing procedures such as heat treatment. Data have been deposited in the Data in Brief Dataverse repository (doi:10.7910/DVN/T41S3V.

Meal ingestion markedly increases liver stiffness suggesting the need for liver stiffness determination in fasting conditions.

Science.gov (United States)

Alvarez, Daniel; Orozco, Federico; Mella, José María; Anders, Maria; Antinucci, Florencia; Mastai, Ricardo

2015-01-01

The introduction of noninvasive liver stiffness (LS) determination has heralded a new stage in the diagnosis and treatment of liver fibrosis. We evaluated the effect of food intake on LS in patients with different degrees of liver disease. We evaluated 24 patients (F≤1, n=11 and F> 1, n=13). LS (Fibroscan®) and portal blood flow (PBF) (Doppler ultrasound) were studied before and 30min after ingestion of a standard liquid meal. Food intake increased PBF (51±10%, p1). Hemodynamic and LS values returned to baseline pre-meal levels within 2hours. LS increases markedly after ingestion of a standard meal, irrespective of the degree of fibrosis. Our results strongly suggest that LS should be measured in fasting conditions. Copyright © 2015 Elsevier España, S.L.U. and AEEH y AEG. All rights reserved.

Gearbox Reliability Collaborative Phase 3 Gearbox 3 Test Report

Energy Technology Data Exchange (ETDEWEB)

Keller, Jonathan [National Renewable Energy Lab. (NREL), Golden, CO (United States); Wallen, Robb [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2017-02-24

Many gearboxes in wind turbines do not achieve their expected design life; they do, however, commonly meet or exceed the design criteria specified in current standards in the gear, bearing, and wind turbine industry as well as third-party certification criteria. The cost of gearbox replacements and rebuilds, as well as the downtime associated with these failures, increases the cost of wind energy. In 2007, the U.S. Department of Energy established the National Renewable Energy Laboratory (NREL) Gearbox Reliability Collaborative (GRC). Its goals are to understand the root causes of premature gearbox failures and to improve their reliability. The GRC is examining a hypothesis that the gap between design-estimated and actual wind turbine gearbox reliability is caused by underestimation of loads, inaccurate design tools, the absence of critical elements in the design process, or insufficient testing. This report describes the recently completed tests of GRC Gearbox 3 in the National Wind Technology Center dynamometer and documents any modifications to the original test plan. In this manner, it serves as a guide for interpreting the publicly released data sets with brief analyses to illustrate the data. The primary test objective was to measure the planetary load-sharing characteristics in the same conditions as the original GRC gearbox design. If the measured load-sharing characteristics are close to the design model, the projected improvement in planetary section fatigue life and the efficacy of preloaded TRBs in mitigating the planetary bearing fatigue failure mode will have been demonstrated. Detailed analysis of that test objective will be presented in subsequent publications.

Pathfinding the Flight Advanced Stirling Convertor Design with the ASC-E3

Science.gov (United States)

Wong, Wayne A.; Wilson, Kyle; Smith, Eddie; Collins, Josh

2012-01-01

The Advanced Stirling Convertor (ASC) was initially developed by Sunpower, Inc. under contract to NASA Glenn Research Center (GRC) as a technology development project. The ASC technology fulfills NASA's need for high efficiency power convertors for future Radioisotope Power Systems (RPS). Early successful technology demonstrations between 2003 to 2005 eventually led to the expansion of the project including the decision in 2006 to use the ASC technology on the Advanced Stirling Radioisotope Generator (ASRG). Sunpower has delivered 22 ASC convertors of progressively mature designs to date to GRC. Currently, Sunpower with support from GRC, Lockheed Martin Space System Company (LMSSC), and the Department of Energy (DOE) is developing the flight ASC-F in parallel with the ASC-E3 pathfinders. Sunpower will deliver four pairs of ASC-E3 convertors to GRC which will be used for extended operation reliability assessment, independent validation and verification testing, system interaction tests, and to support LMSSC controller verification. The ASC-E3 and -F convertors are being built to the same design and processing documentation and the same product specification. The initial two pairs of ASC-E3 are built before the flight units and will validate design and processing changes prior to implementation on the ASC-F flight convertors. This paper provides a summary on development of the ASC technology and the status of the ASC-E3 build and how they serve the vital pathfinder role ahead of the flight build for ASRG. The ASRG is part of two of the three candidate missions being considered for selection for the Discovery 12 mission.

Nuclear Technology Division annual progress report for period ending June 30, 1974

International Nuclear Information System (INIS)

1975-01-01

Abstracts of research projects are presented concerning nuclear properties, general reactor development and support, test reactor operations support, LOFT support, PBF support, FEFPL support, TRSP support, techniques and instrumentation, non-nuclear energy sources, and related activities of division personnel. (U.S.)

NASA Glenn Research Center Experience with "LENR Phenomenon"

Science.gov (United States)

Wrbanek, Susan Y.; Fralick, Gustave C.; Wrbanek, John D.; Niedra, Janis M.

2012-01-01

Since 1989 NASA Glenn Research Center (GRC) has performed some small-scale limited experiments that show evidence of effects claimed by some to be evidence of Low Energy Nuclear Reactions (LENR). The research at GRC has involved observations and work on measurement techniques for observing the temperature effects in reactions of isotopes of hydrogen with palladium hydrides. The various experiments performed involved loading Pd with gaseous H2 and D2, and exposing Pd thin films to multi-bubble sonoluminescence in regular and deuterated water. An overview of these experiments and their results will be presented.

NASA Glenn Research Center Experience with LENR Phenomenon

Science.gov (United States)

Wrbanek, Susan Y.; Fralick, Gustave C.; Wrbanek, John D.; Niedra, Janis M.

2012-01-01

Since 1989 NASA Glenn Research Center (GRC) has performed some small-scale limited experiments that show evidence of effects claimed by some to be evidence of Low Energy Nuclear Reactions (LENR). The research at GRC has involved observations and work on measurement techniques for observing the temperature effects in reactions of isotopes of hydrogen with palladium hydrides. The various experiments performed involved loading Pd with gaseous H2 and D2, and exposing Pd thin films to multi-bubble sonoluminescence in regular and deuterated water. An overview of these experiments and their results will be presented.

Targeting the poorest in a performance-based financing programme in northern Cameroon

NARCIS (Netherlands)

I.J.E. Flink (Ilse); Ziebe, R. (Roland); Vagaï, D. (Djebba); Van De Looij, F. (Frank); Van 'T Riet, H. (Hilda); A.J. Houweling (Tanja)

2016-01-01

textabstractPerformance-Based Financing (PBF) is a promising approach to improve health system performance in developing countries, but there are concerns that it may inadequately address inequalities in access to care. Incentives for reaching the poor may prove beneficial, but evidence remains

The impact of obesity on foot morphology in women aged 48 years or older

Directory of Open Access Journals (Sweden)

Kristína Tománková

2015-06-01

Full Text Available Background: Obesity is major risk factor for many diseases within society and represents extensive loads for the feet which lead to various foot disorders and deformities. Objective: The aim of this study was to evaluate the impact of obesity as represented by percent body fat (PBF on foot morphology. Methods: The study sample included 139 Czech women aged 48-69 years. The women were divided into two groups by PBF: non-obese women (NOW (n = 66; PBF < 35% and obese women (OW (n = 73; PBF > 35%. Measurements included % PBF and width, length and angle dimensions of foot. The Chippaux-Smirak index (CSI was calculated for each foot. Results: We found significant differences between OW and NOW in these parameters: direct forefoot width (sin. p = .02, rpb = .20, direct heel width (sin. p = .01, rpb = .22; dex. p < .01, rpb = .22, hallux angle (sin. p = .01, rpb = .25 and CSI (sin. p < .01, rpb = .26; dex. p < .01, rpb = .27. The results showed that the mean values of the heel width and CSI were significantly higher in OW on both feet, the mean values of forefoot width only on the left foot. Conclusions: Results proved that obesity impacts all parts of the foot (heel, longitudinal foot arch, forefoot. Despite significant differences of the CSI between NOW and OW, the number of subjects with flat feet was in both groups negligible.

The effect of swimming on pulmonary functions, blood pressure and body composition

Directory of Open Access Journals (Sweden)

Hasan Aykut Aysan

2011-03-01

Full Text Available The aim of this study was to investigate theeffect of 8 week swimming exercise on adult sedentarymen’s respiratory functions, resting heart rate, bloodpressures and body composition.Materials and methods: A total of 80 volunteers (40 inthe study group, 40 in the control group, aged between20 and 29 years were included. The participants’ bodyweight, percentage of body fat (PBF, body mass index(BMI, resting heart rate (RHR, systolic (SBP and diastolicblood pressures (DBP, and respiratory functionswere measured before and after 8 week of swimmingtraining program and compared with each other.Results: Significant decreases were observed betweenpre- and post-exercise (following 8 weeks exercise trainingin PBF (18.1±5% vs. 14.3±4%, respectively, RHR(83.1±6/min vs. 74.6±3.8/min, DBP (83±7,2 mmHg vs.74.6±3,8 mmHg (p0.001.No significant differences were found between pre-testand post-test measurements in body weight (78.1±11.4kg vs. 75.3±9.9 kg, respectively, BMI (25.2±3.9 kg/m2 vs.24.3±2.8 kg/m2 and SBP (127.6±11.8 mmHg vs.115.8±5.1 mmHg (p>0.05.Conclusion: Eight weeks swimming exercise reduced thePBF and increased the forced expiration volume, maximumvoluntarily ventilation, vital capacity and forced vitalcapacity. Swimming training also decreased RHR andbalanced DBP. J Clin Exp Invest 2011; 2(1: 35-41

Stirling Technology Development at NASA GRC. Revised

Science.gov (United States)

Thieme, Lanny G.; Schreiber, Jeffrey G.; Mason, Lee S.

2002-01-01

The Department of Energy, Stirling Technology Company (STC), and NASA Glenn Research Center (NASA Glenn) are developing a free-piston Stirling convertor for a high-efficiency Stirling Radioisotope Generator (SRG) for NASA Space Science missions. The SRG is being developed for multimission use, including providing electric power for unmanned Mars rovers and deep space missions. NASA Glenn is conducting an in-house technology project to assist in developing the convertor for space qualification and mission implementation. Recent testing, of 55-We Technology Demonstration Convertors (TDC's) built by STC includes mapping, of a second pair of TDC's, single TDC testing, and TDC electromagnetic interference and electromagnetic compatibility characterization on a nonmagnetic test stand. Launch environment tests of a single TDC without its pressure vessel to better understand the convertor internal structural dynamics and of dual-opposed TDC's with several engineering mounting structures with different natural frequencies have recently been completed. A preliminary life assessment has been completed for the TDC heater head, and creep testing of the IN718 material to be used for the flight convertors is underway. Long-term magnet aging tests are continuing to characterize any potential aging in the strength or demagnetization resistance of the magnets used in the linear alternator (LA). Evaluations are now beginning on key organic materials used in the LA and piston/rod surface coatings. NASA Glenn is also conducting finite element analyses for the LA, in part to look at the demagnetization margin on the permanent magnets. The world's first known integrated test of a dynamic power system with electric propulsion was achieved at NASA Glenn when a Hall-effect thruster was successfully operated with a free-piston Stirling power source. Cleveland State University is developing a multidimensional Stirling computational fluid dynamics code to significantly improve Stirling loss predictions and assist in identifying convertor areas for further improvements. This paper will update the status and results for these efforts.

Wind-US Users Guide Version 4.0

Science.gov (United States)

Yoder, Dennis A.

2016-01-01

Wind-US is a computational platform which may be used to numerically solve various sets of equations governing physical phenomena. Currently, the code supports the solution of the Euler and Navier-Stokes equations of fluid mechanics, along with supporting equation sets governing turbulent and chemically reacting flows. Wind-US is a product of the NPARC Alliance, a partnership between the NASA Glenn Research Center (GRC) and the Arnold Engineering Development Complex (AEDC) dedicated to the establishment of a national, applications-oriented flow simulation capability. The Boeing Company has also been closely associated with the Alliance since its inception, and represents the interests of the NPARC User's Association. The "Wind-US User's Guide" describes the operation and use of Wind-US, including: a basic tutorial; the physical and numerical models that are used; the boundary conditions; monitoring convergence; the files that are read and/or written; parallel execution; and a complete list of input keywords and test options. For current information about Wind-US and the NPARC Alliance, please see the Wind-US home page at http://www.grc.nasa.gov/WWW/winddocs/ and the NPARC Alliance home page at http://www.grc.nasa.gov/WWW/wind/.

Advanced Stirling Convertor (ASC) Technology Maturation in Preparation for Flight

Science.gov (United States)

Wong, Wayne A.; Cornell, Peggy A.

2012-01-01

The Advanced Stirling Convertor (ASC) is being developed by an integrated team of Sunpower and National Aeronautics and Space Administration s (NASA s) Glenn Research Center (GRC). The ASC development, funded by NASA s Science Mission Directorate, started as a technology development effort in 2003 and has since evolved through progressive convertor builds and successful testing to demonstrate high conversion efficiency, low mass, and capability to meet long-life Radioisotope Power System (RPS) requirements. The technology has been adopted by the Department of Energy and Lockheed Martin Space Systems Company s Advanced Stirling Radioisotope Generator (ASRG), which has been selected for potential flight demonstration on Discovery 12. This paper provides an overview of the status of ASC development including the most recent ASC-E2 convertors that have been delivered to GRC and an introduction to the ASC-E3 and ASC flight convertors that Sunpower will build next. The paper also describes the technology maturation and support tasks being conducted at GRC to support ASC and ASRG development in the areas of convertor and generator extended operation, high-temperature materials, heater head life assessment, organics, nondestructive inspection, spring fatigue testing, and other reliability verification tasks.

Mechanical properties and microstructure evaluation of powder bed fused inconel 625 nickel alloy

Energy Technology Data Exchange (ETDEWEB)

Brand, Michael J. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-04-19

The objectives of this report were to optimize and fabricate full density Inconel 625 samples using direct metal laser fusion, an additive manufacturing process; and to compare and evaluate precipitation and solid solution strengthening of Inconel 625 produced by PBF to conventional processed material.

76 FR 36103 - Combined Notice of Filings #1

Science.gov (United States)

2011-06-21

...-2077-005. Applicants: Delaware City Refining Company LLC, PBF Power Marketing LLC. Desciption: Delaware... self-recertification] listed above, do not institute a proceeding regarding qualifying facility status... lieu of paper, using the FERC Online links at http://www.ferc.gov . To facilitate electronic service...

Mineral profiling, carcass quality and sensory evaluation of broiler ...

African Journals Online (AJOL)

An investigation to determine the mineral composition, carcass quality and organoleptic properties of the meat of broilers fed basal broiler feeds supplemented with different leaf meals was conducted. Four treatments: basal proprietary broiler feed only (T1 - PBF) as control, basal proprietary broiler feeds supplemented with ...

Breast milk and energy intake in exclusively, predominantly, and partially breast-fed infants

NARCIS (Netherlands)

Haisma, H; Coward, WA; Albernaz, E; Visser, GH; Wells, JCK; Wright, A; Victoria, CG; Victora, C.G.

2003-01-01

Objective: To investigate the extent to which breast milk is replaced by intake of other liquids or foods, and to estimate energy intake of infants defined as exclusively (EBF), predominantly (PBF) and partially breast-fed (PartBF). Design: Cross-sectional. Setting: Community-based study in urban

Blowdown mass flow measurements during the Power Burst Facility LOC-11C test

International Nuclear Information System (INIS)

Broughton, J.M.; MacDonald, P.E.

1979-01-01

An interpretation and evaluation of the two-phase coolant mass flow measurements obtained during Test LOC-11C performed in the Power Burst Facility (PBF) at the Idaho National Engineering Laboratory (INEL) are presented. Although a density gradient existed within the pipe between 1 and 6 s, the homogeneous flow model used to calculate the coolant mass flow from the measured mixture density, momentum flux, and volumetric flow was found to be generally satisfactory. A cross-sectional average density was determined by fitting a linear density gradient through the upper and lower chordal densities obtained from a three-beam gamma densitometer and then combining the result with the middle beam density. The integrated measured coolant mass flow was subsequently found to be within 5% if the initial mass inventory of the PBF loss-of-coolant accident (LOCA) system. The posttest calculations using the RELAP4/MOD6 computer code to determine coolant mass flow for Test LOC-11C also agreed well with the measured data

Raman and luminescence spectroscopy of zirconium oxide with the use of the MOLE microprobe

International Nuclear Information System (INIS)

Doyle, T.E.; Alvarez, J.L.

1984-01-01

Raman and luminescence spectroscopy with the use of the MOLE microprobe has been used to characterize ZrO 2 originating from oxidized fuel-rod cladding in nuclear accidents. Micro-Raman analysis of samples from Three Mile Island Unit 2 and the Power Burst Facility identified tetragonal and cubic ZrO 2 . The tetragonal and cubic phases are high-temperature polymorphs of ZrO 2 and provide information about temperatures and hydrogen formation in the TMI-2 core. The data suggest that the tetragonal ZrO 2 in TMI-2 samples was stabilized by a crystallite size effect, whereas cubic ZrO 2 in PBF debris samples was stabilized by impurities. Luminescence was used to differentiate yttria-stabilized ZrO 2 ceramics and oxidized fuel-rod cladding in PBF debris samples. The ZrO 2 ceramics produced strong, sharp luminescence peaks which indicated the presence of titanium and yttria in the ZrO 2 . Oxidized fuel-rod cladding displayed no luminescence

Analysis of association of gene variants with obesity traits in New Zealand European children at 6 years of age.

Science.gov (United States)

Krishnan, Mohanraj; Thompson, John M D; Mitchell, Edwin A; Murphy, Rinki; McCowan, Lesley M E; Shelling, Andrew N; On Behalf Of The Children Of Scope Study Group, G

2017-07-25

Childhood obesity is a public health problem, which is associated with a long-term increased risk of cardiovascular disease and premature mortality. Several gene variants have previously been identified that have provided novel insights into biological factors that contribute to the development of obesity. As obesity tracks through childhood into adulthood, identification of the genetic factors for obesity in early life is important. The objective of this study was to identify putative associations between genetic variants and obesity traits in children at 6 years of age. We recruited 1208 children of mothers from the New Zealand centre of the international Screening for Pregnancy Endpoints (SCOPE) study. Eighty common genetic variants associated with obesity traits were evaluated by the Sequenom assay. Body mass index standardised scores (BMI z-scores) and percentage body fat (PBF; measured by bio-impedance assay (BIA)) were used as anthropometric measures of obesity. A positive correlation was found between BMI z-scores and PBF (p obesity and obesity traits in New Zealand European children.

DESAFIOS PARA A COORDENAÇÃO INTERGOVERNAMENTAL DO PROGRAMA BOLSA FAMÍLIA

Directory of Open Access Journals (Sweden)

Claudia Regina Baddini Curralero

2011-08-01

Full Text Available The paper examines the intergovernmental coordination of the Bolsa Família Program (PBF, given its goal to tackle poverty in acountry with deep social and regional inequality. It seeks to qualify the debate on the centralization of cash transfer programs in Brazil through the analysis of intergovernmental relations adopted under the three main dimensions of the PBF - cash transfer, monitoring of conditionalities and articulation of complementary programs - considering the federative implications derived from the intersectoral perspective that drives the Program. Two categories of challenges are highlighted. The first one relates to the need for greater investment in space and opportunities for intergovernmental negotiation, especially in the dimension of income transfer, which initially was characterized by centralization. In the second, the intergovernmental matter demands the organization of a coordinated national strategy for the articulation of complementary programs, suggesting greater involvement of states in the regional coordination of the Program

Anaesthesia for the child with congenital heart disease: pointers and ...

African Journals Online (AJOL)

Increased pulmonary blood flow (PBF) causes a volume or pressure overload to the ... venous drainage (TAPVD), high left atrial pressure (e.g. hypoplastic left heart ... function. Congenital heart disease (CHD) is the commonest birth defect, with a reported .... Is there valve regurgitation? ... tubing to avoid systemic air emboli.

Tribomechanical micronization and activation of whey protein ...

Indian Academy of Sciences (India)

R. Narasimhan (Krishtel eMaging) 1461 1996 Oct 15 13:05:22

Faculty of Food Technology and Biotechnology, University of Zagreb,. Pierottijeva 6, 10000 Zagreb, Croatia e-mail: zherceg@pbf.hr. MS received 11 December 2002; revised 9 September 2003. Abstract. Tribomechanics is a part of physics that is concerned with the study of phenomena that appear during milling under ...

Genetic Segregation Analysis of a Rapeseed Dwarf Mutant

International Nuclear Information System (INIS)

Xiang, G.; Yu, S.; Zhang, T.; Zhao, J.; Lei, S.; Du, C.

2016-01-01

Dwarf resources in Brassica napus are very important for developing high-yield cultivars through dwarf-type and lodging-resistant breeding. However, few dwarf varieties have been available for this species. Here, we reported a new rapeseed dwarf mutant GRC1157, which exhibits obvious phenotypic variations on dwarf. Six generations (P /sub 1/, P/sub 1/, F/sub 1/, F/sub 1/, B/sub 1/, and B/sub 1/) were produced from a cross between dwarf mutant GRC1157 and an elite tall-type line XR16 to analyze genetic inheritances of plant height (PH), numbers of the 1st valid branch (VBN), main inflorescence length (MIL), pod numbers per main inflorescence (MPN), pod length (PL) and seed numbers per pod (PSN) using the mixed major gene plus polygene inheritance model. The genetic analysis shows different traits were controlled by different inheritance models: PH and PL by two pairs of additive-dominant-epistatic major genes plus additive-dominant-epistatic polygenes, MPN and PSN by two-pair additive-dominant-epistatic major genes plus additive-dominant polygenes, MIL by two-pair additive-dominant-epistatic major genes and VBN by one-pair additive-dominant major genes plus additive-dominant-epistatic polygenes. Furthermore, positive correlations between PH and some other traits were observed, suggesting that some traits may be co-regulated by several linkage or same loci/genes. In addition, high heritability (40.35-93.7 percent) were found for five traits (except VBN) in different segregating generations, indicating these traits were mainly affected by hereditary factors and suitable for early artificial selection. In sum, the dwarf mutant GRC1157 can serve as a valuable resource for rapeseed dwarf breeding and the genetic analysis in this study provided a foundation for further mapping and cloning dwarf genes in mutant GRC1157. (author)

Small Radioisotope Power System Testing at NASA Glenn Research Center

Science.gov (United States)

Dugala, Gina; Bell, Mark; Oriti, Salvatore; Fraeman, Martin; Frankford, David; Duven, Dennis

2013-01-01

In April 2009, NASA Glenn Research Center (GRC) formed an integrated product team (IPT) to develop a Small Radioisotope Power System (SRPS) utilizing a single Advanced Stirling Convertor (ASC) with passive balancer. A single ASC produces approximately 80 We making this system advantageous for small distributed lunar science stations. The IPT consists of Sunpower, Inc., to provide the single ASC with a passive balancer, The Johns Hopkins University Applied Physics Laboratory (JHUAPL) to design an engineering model Single Convertor Controller (SCC) for an ASC with a passive balancer, and NASA GRC to provide technical support to these tasks and to develop a simulated lunar lander test stand. The single ASC with a passive balancer, simulated lunar lander test stand, and SCC were delivered to GRC and were tested as a system. The testing sequence at GRC included SCC fault tolerance, integration, electromagnetic interference (EMI), vibration, and extended operation testing. The SCC fault tolerance test characterized the SCCs ability to handle various fault conditions, including high or low bus power consumption, total open load or short circuit, and replacing a failed SCC card while the backup maintains control of the ASC. The integrated test characterized the behavior of the system across a range of operating conditions, including variations in cold-end temperature and piston amplitude, including the emitted vibration to both the sensors on the lunar lander and the lunar surface. The EMI test characterized the AC and DC magnetic and electric fields emitted by the SCC and single ASC. The vibration test confirms the SCCs ability to control the single ASC during launch. The extended operation test allows data to be collected over a period of thousands of hours to obtain long term performance data of the ASC with a passive balancer and the SCC. This paper will discuss the results of each of these tests.

Planetary Load Sharing in Three-Point- Mounted Wind Turbine Gearboxes: Preprint

Energy Technology Data Exchange (ETDEWEB)

Guo, Yi [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Keller, Jonathan A [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

2017-09-15

Wind turbine gearboxes do not achieve their expected design life. The cost of gearbox replacements and rebuilds and the downtime associated with these failures increase the cost of wind energy. In 2007, the U.S. Department of Energy established the National Renewable Energy Laboratory (NREL) Gearbox Reliability Collaborative (GRC). Its goals are to understand the root causes of premature gearbox failures and improve their reliability. To date, the GRC has focused on a 750-kW drivetrain with a three-stage, three-point-mounted gearbox. A nonproprietary version of the gearbox containing CRBs with C3 clearances in the planetary stage was customized. Two of these gearboxes, GB1 and GB2, were manufactured and then tested in the National Wind Technology Center's 2.5-MW dynamometer and in the field. Major GRC findings include the detrimental effect of rotor moments on planetary load sharing and predicted fatigue, and the risk of bearing sliding in low-torque conditions for three-point configuration drivetrains. Based on the knowledge gained from testing and analysis of the original design, the GRC gearbox was redesigned to improve its load-sharing characteristics and predicted fatigue. This new gearbox is named GB3. As shown in Figure 1, its key improvement is the incorporation of preloaded TRBs that support the planet carrier and planets. Roller loads can be optimized and bearing life maximized with a small preload [4]. These preloaded bearings, along with interference-fitted planet pins, improve alignments and load-sharing characteristics. A semi-integrated planet bearing design also increases capacity and eliminates outer race fretting. Romax Technology, with Powertrain Engineers and the Timken Company (Timken), completed the redesign. Timken manufactured and instrumented the planet gears and bearings. Brad Foote Gearing manufactured the other gearing and assembled the gearbox.

Cumulative t-link threshold models for the genetic analysis of calving ease scores

Directory of Open Access Journals (Sweden)

Tempelman Robert J

2003-09-01

Full Text Available Abstract In this study, a hierarchical threshold mixed model based on a cumulative t-link specification for the analysis of ordinal data or more, specifically, calving ease scores, was developed. The validation of this model and the Markov chain Monte Carlo (MCMC algorithm was carried out on simulated data from normally and t4 (i.e. a t-distribution with four degrees of freedom distributed populations using the deviance information criterion (DIC and a pseudo Bayes factor (PBF measure to validate recently proposed model choice criteria. The simulation study indicated that although inference on the degrees of freedom parameter is possible, MCMC mixing was problematic. Nevertheless, the DIC and PBF were validated to be satisfactory measures of model fit to data. A sire and maternal grandsire cumulative t-link model was applied to a calving ease dataset from 8847 Italian Piemontese first parity dams. The cumulative t-link model was shown to lead to posterior means of direct and maternal heritabilities (0.40 ± 0.06, 0.11 ± 0.04 and a direct maternal genetic correlation (-0.58 ± 0.15 that were not different from the corresponding posterior means of the heritabilities (0.42 ± 0.07, 0.14 ± 0.04 and the genetic correlation (-0.55 ± 0.14 inferred under the conventional cumulative probit link threshold model. Furthermore, the correlation (> 0.99 between posterior means of sire progeny merit from the two models suggested no meaningful rerankings. Nevertheless, the cumulative t-link model was decisively chosen as the better fitting model for this calving ease data using DIC and PBF.

Gearbox Reliability Collaborative Bearing Calibration

Energy Technology Data Exchange (ETDEWEB)

van Dam, J.

2011-10-01

NREL has initiated the Gearbox Reliability Collaborative (GRC) to investigate the root cause of the low wind turbine gearbox reliability. The GRC follows a multi-pronged approach based on a collaborative of manufacturers, owners, researchers and consultants. The project combines analysis, field testing, dynamometer testing, condition monitoring, and the development and population of a gearbox failure database. At the core of the project are two 750kW gearboxes that have been redesigned and rebuilt so that they are representative of the multi-megawatt gearbox topology currently used in the industry. These gearboxes are heavily instrumented and are tested in the field and on the dynamometer. This report discusses the bearing calibrations of the gearboxes.

2010 CATALYSIS GORDON RESEARCH CONFERENCE, JUNE 27 - JULY 2, 2010, NEW LONDON, NEW HAMPSHIRE

Energy Technology Data Exchange (ETDEWEB)

Abhaya Datye

2010-07-02

Catalysis is a key technology for improving the quality of life while simultaneously reducing the adverse impact of human activities on the environment. The discovery of new catalytic processes and the improvement of existing ones are also critically important for securing the nation's energy supply. The GRC on Catalysis is considered one the most prestigious conference for catalysis research, bringing together leading researchers from both academia, industry and national labs to discuss the latest, most exciting research in catalysis and the future directions for the field. The 2010 GRC on Catalysis will follow time-honored traditions and feature invited talks from the world's leading experts in the fundamentals and applications of catalytic science and technology. We plan to have increased participation from industry. The extended discussions in the company of outstanding thinkers will stimulate and foster new science. The conference will include talks in the following areas: Alternative feedstocks for chemicals and fuels, Imaging and spectroscopy, Design of novel catalysts, Catalyst preparation fundamentals, Molecular insights through theory, Surface Science, Catalyst stability and dynamics. In 2010, the Catalysis conference will move to a larger conference room with a new poster session area that will allow 40 posters per session. The dorm rooms provide single and double accommodations, free WiFi and the registration fee includes all meals and the famous lobster dinner on Thursday night. Afternoons are open to enjoy the New England ambiance with opportunities for hiking, sailing, golf and tennis to create an outstanding conference that will help you network with colleagues, and make long lasting connections.

Heated Tube Facility

Data.gov (United States)

Federal Laboratory Consortium — The Heated Tube Facility at NASA GRC investigates cooling issues by simulating conditions characteristic of rocket engine thrust chambers and high speed airbreathing...

Mechanical properties and microstructure analysis of fly ash geopolymeric recycled concrete.

Science.gov (United States)

Shi, X S; Collins, F G; Zhao, X L; Wang, Q Y

2012-10-30

Six mixtures with different recycled aggregate (RA) replacement ratios of 0%, 50% and 100% were designed to manufacture recycled aggregate concrete (RAC) and alkali-activated fly ash geopolymeric recycled concrete (GRC). The physical and mechanical properties were investigated indicating different performances from each other. Optical microscopy under transmitted light and scanning electron microscopy (SEM) coupled with energy dispersive X-ray spectroscopy (EDX) were carried out in this study in order to identify the mechanism underlying the effects of the geopolymer and RA on concrete properties. The features of aggregates, paste and interfacial transition zone (ITZ) were compared and discussed. Experimental results indicate that using alkali-activated fly ash geopolymer as replacement of ordinary Portland cement (OPC) effectively improved the compressive strength. With increasing of RA contents in both RAC and GRC, the compressive strength decreased gradually. The microstructure analysis shows that, on one hand, the presence of RA weakens the strength of the aggregates and the structure of ITZs; on the other hand, due to the alkali-activated fly ash in geopolymer concrete, the contents of Portlandite (Ca(OH)(2)) and voids were reduced, as well as improved the matrix homogeneity. The microstructure of GRC was changed by different reaction products, such as aluminosilicate gel. Copyright © 2012 Elsevier B.V. All rights reserved.

Gearbox Reliability Collaborative Phase 3 Gearbox 2 Test Plan

Energy Technology Data Exchange (ETDEWEB)

Link, H.; Keller, J.; Guo, Y.; McNiff, B.

2013-04-01

Gearboxes in wind turbines have not been achieving their expected design life even though they commonly meet or exceed the design criteria specified in current design standards. One of the basic premises of the National Renewable Energy Laboratory (NREL) Gearbox Reliability Collaborative (GRC) is that the low gearbox reliability results from the absence of critical elements in the design process or insufficient design tools. Key goals of the GRC are to improve design approaches and analysis tools and to recommend practices and test methods resulting in improved design standards for wind turbine gearboxes that lower the cost of energy (COE) through improved reliability. The GRC uses a combined gearbox testing, modeling and analysis approach, along with a database of information from gearbox failures collected from overhauls and investigation of gearbox condition monitoring techniques to improve wind turbine operations and maintenance practices. Testing of Gearbox 2 (GB2) using the two-speed turbine controller that has been used in prior testing. This test series will investigate non-torque loads, high-speed shaft misalignment, and reproduction of field conditions in the dynamometer. This test series will also include vibration testing using an eddy-current brake on the gearbox's high speed shaft.

A Hybrid Power Management (HPM) Based Vehicle Architecture

Science.gov (United States)

Eichenberg, Dennis J.

2011-01-01

Society desires vehicles with reduced fuel consumption and reduced emissions. This presents a challenge and an opportunity for industry and the government. The NASA John H. Glenn Research Center (GRC) has developed a Hybrid Power Management (HPM) based vehicle architecture for space and terrestrial vehicles. GRC's Electrical and Electromagnetics Branch of the Avionics and Electrical Systems Division initiated the HPM Program for the GRC Technology Transfer and Partnership Office. HPM is the innovative integration of diverse, state-of-the-art power devices in an optimal configuration for space and terrestrial applications. The appropriate application and control of the various power devices significantly improves overall system performance and efficiency. The basic vehicle architecture consists of a primary power source, and possibly other power sources, providing all power to a common energy storage system, which is used to power the drive motors and vehicle accessory systems, as well as provide power as an emergency power system. Each component is independent, permitting it to be optimized for its intended purpose. This flexible vehicle architecture can be applied to all vehicles to considerably improve system efficiency, reliability, safety, security, and performance. This unique vehicle architecture has the potential to alleviate global energy concerns, improve the environment, stimulate the economy, and enable new missions.

78 FR 21353 - Combined Notice of Filings #1

Science.gov (United States)

2013-04-10

... Partners, LLC, Delaware City Refining Company, LLC, PBF Power Marketing LLC. Description: Supplement to Lea.... Description: Duquesne submits new OATT Attachment H-17C to be effective 6/1/2013. Filed Date: 4/1/13.... Docket Numbers: ER13-1222-000. Applicants: NV Energy, Inc. Description: OATT Revisions to Attachment N...

Multi-Mission SDR, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — Wireless transceivers used for NASA space missions have traditionally been highly custom and mission specific. Programs such as the GRC Space Transceiver Radio...

Low Cost Radiator for Fission Power Thermal Control, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — NASA Glenn Research Center (GRC) is developing fission power system technology for future space transportation and surface power applications. The early systems are...

Effect of graded levels of Parkia biglobosa in concentrate diets on ...

African Journals Online (AJOL)

Ether extract and hemicellulose contents, digestibility of DM, OM and neutral detergent fibre, and N intake, absorbtion and retentionwere greatest (p<0.05) for the control diet (0%) compared to the PBF based diets. Digestibility of acid detergent fibre and acid detergent lignin, and N retention (N retained as % of N intake) ...

Behavior Management and Behavioral Change: How Can We Tell Them Apart?

Science.gov (United States)

Olive, Edna

2010-01-01

Understanding the differences between behavior management and behavior change helps adults identify the differences between the two and teaches them what they can do to be effective in the use of both. This article introduces Positive Behavior Facilitation (PBF) Tool #3 which aims to support adults in understanding the differences between behavior…

Spinal imaging and image analysis

CERN Document Server

Yao, Jianhua

2015-01-01

This book is instrumental to building a bridge between scientists and clinicians in the field of spine imaging by introducing state-of-the-art computational methods in the context of clinical applications.  Spine imaging via computed tomography, magnetic resonance imaging, and other radiologic imaging modalities, is essential for noninvasively visualizing and assessing spinal pathology. Computational methods support and enhance the physician’s ability to utilize these imaging techniques for diagnosis, non-invasive treatment, and intervention in clinical practice. Chapters cover a broad range of topics encompassing radiological imaging modalities, clinical imaging applications for common spine diseases, image processing, computer-aided diagnosis, quantitative analysis, data reconstruction and visualization, statistical modeling, image-guided spine intervention, and robotic surgery. This volume serves a broad audience as  contributions were written by both clinicians and researchers, which reflects the inte...

Reverberant Acoustic Test Facility (RATF)

Data.gov (United States)

Federal Laboratory Consortium — The very large Reverberant Acoustic Test Facility (RATF) at the NASA Glenn Research Center (GRC), Plum Brook Station, is currently under construction and is due to...

Finite Internal Temperature Slide for Use with Colloid Experiments, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — The Light Microscopy Module (LMM), developed and managed by NASA Glenn Research Center (GRC), is producing fascinating results. LMM will yield even more astonishing...

Toward Better Mapping between Regulations and Operations of Enterprises Using Vocabularies and Semantic Similarity

Directory of Open Access Journals (Sweden)

Sagar Sunkle

2015-12-01

Full Text Available Industry governance, risk, and compliance (GRC solutions stand to gain from various analyses offered by formal compliance checking approaches. Such adoption is made difficult by the fact that most formal approaches assume that a mapping between concepts of regulations and models of operational specifics exists. Industry solutions offer tagging mechanisms to map regulations to operational specifics; however, they are mostly semi-formal in nature and tend to rely extensively on experts. We propose to use Semantics of Business Vocabularies and Rules along with similarity measures to create an explicit mapping between concepts of regulations and models of operational specifics of the enterprise. We believe that our work-in-progress takes a step toward adapting and leveraging formal compliance checking approaches in industry GRC solutions.

Stirling Radioisotope Power System as an Alternative for NASAs Deep Space Missions

Science.gov (United States)

Shaltens, R. K.; Mason, L. S.; Schreiber, J. G.

2001-01-01

The NASA Glenn Research Center (GRC) and the Department of Energy (DOE) are developing a free-piston Stirling convertor for a Stirling Radioisotope Power System (SRPS) to provide on-board electric power for future NASA deep space missions. The SRPS currently being developed provides about 100 watts and reduces the amount of radioisotope fuel by a factor of four over conventional Radioisotope Thermoelectric Generators (RTG). The present SRPS design has a specific power of approximately 4 W/kg which is comparable to an RTG. GRC estimates for advanced versions of the SRPS with improved heat source integration, lightweight Stirling convertors, composite radiators, and chip-packaged controllers improves the specific mass to about 8 W/kg. Additional information is contained in the original extended abstract.

Hypersonic Vehicle Propulsion System Simplified Model Development

Science.gov (United States)

Stueber, Thomas J.; Raitano, Paul; Le, Dzu K.; Ouzts, Peter

2007-01-01

This document addresses the modeling task plan for the hypersonic GN&C GRC team members. The overall propulsion system modeling task plan is a multi-step process and the task plan identified in this document addresses the first steps (short term modeling goals). The procedures and tools produced from this effort will be useful for creating simplified dynamic models applicable to a hypersonic vehicle propulsion system. The document continues with the GRC short term modeling goal. Next, a general description of the desired simplified model is presented along with simulations that are available to varying degrees. The simulations may be available in electronic form (FORTRAN, CFD, MatLab,...) or in paper form in published documents. Finally, roadmaps outlining possible avenues towards realizing simplified model are presented.

Image compression of bone images

International Nuclear Information System (INIS)

Hayrapetian, A.; Kangarloo, H.; Chan, K.K.; Ho, B.; Huang, H.K.

1989-01-01

This paper reports a receiver operating characteristic (ROC) experiment conducted to compare the diagnostic performance of a compressed bone image with the original. The compression was done on custom hardware that implements an algorithm based on full-frame cosine transform. The compression ratio in this study is approximately 10:1, which was decided after a pilot experiment. The image set consisted of 45 hand images, including normal images and images containing osteomalacia and osteitis fibrosa. Each image was digitized with a laser film scanner to 2,048 x 2,048 x 8 bits. Six observers, all board-certified radiologists, participated in the experiment. For each ROC session, an independent ROC curve was constructed and the area under that curve calculated. The image set was randomized for each session, as was the order for viewing the original and reconstructed images. Analysis of variance was used to analyze the data and derive statistically significant results. The preliminary results indicate that the diagnostic quality of the reconstructed image is comparable to that of the original image

In-Situ Resource Utilization: Carbon Dioxide Collection, Separation, and Pressurization

Data.gov (United States)

National Aeronautics and Space Administration — The atmosphere of Mars is predominantly carbon dioxide (95.5 percent), with nitrogen, argon, and trace gases comprising the remaining portion. KSC and GRC are...

Low Cost Radiator for Fission Power Thermal Control, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — NASA GRC is developing fission power system technology for future space transportation and surface power applications. The early systems are envisioned in the 10 to...

Ductus arteriosus stenting: A promising percutaneous palliation in patients with duct-dependent pulmonary circulation.

Science.gov (United States)

Raval, Abhishek; Thakkar, Bhavesh; Madan, Tarun; Oswal, Nilesh; Garg, Rajiv; Umalkar, Rhshikesh; Shah, Komal; Maheriya, Bhumika

2016-11-01

We aimed to study the feasibility and outcomes of ductal stenting in patients with duct-dependent pulmonary blood flow (PBF). Duct-dependent hypoxic patients with confluent pulmonary artery (PA) branches were enrolled for ductal stenting and followed regularly. Sixty patients, with a median age of 12 (1-1095) days and weight of 2.8 (2.2-8.9) kg, were enrolled. Median right PA (RPA) and left PA (LPA) Z-scores were -1.23 (-10.54 to 2.81) and -0.96 (-8.03 to 3.0), respectively. Mean narrowest ductal diameter was 1.73±0.57 mm and length was 12.78±3.32 mm. Sixty-four stents with mean diameter of 4.21±0.32 mm and length of 14.34±3.44 mm were deployed in 59 patients. The procedure was unsuccessful in one. Post-stenting mean oxygen saturation (SO 2 ) increased significantly from baseline of 68.88±7.47% to 90.43±6.04% (pedema in one patient and acute stent occlusion in another. At a median follow-up of eight (2-14) months, mean SO 2 (80.04±7.54%) was significantly higher than baseline (p<0.0001). Median RPA and LPA Z-scores, 0.56 (-2.89 to 3.29) and -0.02 (-2.81 to 3.86), respectively, were significantly higher than baseline. Six patients required re-interventions (shunt in three and angioplasty in three). Six patients died, three due to sepsis and another three with worsened cyanosis due to impaired PBF, probably due to ductal occlusion. Ductal stenting is an effective palliation in patients with duct-dependent PBF. It maintains adequate SO 2 and promotes balanced PA growth at mid-term follow-up. Copyright © 2016 Sociedade Portuguesa de Cardiologia. Publicado por Elsevier España, S.L.U. All rights reserved.

Gene-by-environment interactions of the CLOCK, PEMT, and GHRELIN loci with average sleep duration in relation to obesity traits using a cohort of 643 New Zealand European children.

Science.gov (United States)

Krishnan, Mohanraj; Shelling, Andrew N; Wall, Clare R; Mitchell, Edwin A; Murphy, Rinki; McCowan, Lesley M E; Thompson, John M D

2017-09-01

Modern technology may have desensitised the 'biological clock' to environmental cues, disrupting the appropriate co-ordination of metabolic processes. Susceptibility to misalignment of circadian rhythms may be partly genetically influenced and effects on sleep quality and duration could predispose to poorer health outcomes. Shorter sleep duration is associated with obesity traits, which are brought on by an increased opportunity to eat and/or a shift of hormonal profile promoting hunger. We hypothesised that increased sleep duration will offset susceptible genetic effects, resulting in reduced obesity risk. We recruited 643 (male: 338; female: 305) European children born to participants in the New Zealand centre of the International Screening for Pregnancy Endpoints sleep study. Ten genes directly involved in the circadian rhythm machinery and a further 20 genes hypothesised to be driven by cyclic oscillations were evaluated by Sequenom assay. Multivariable regression was performed to test the interaction between gene variants and average sleep length (derived from actigraphy), in relation to obesity traits (body mass index (BMI) z-scores and percentage body fat (PBF)). No association was found between average sleep length and BMI z-scores (p = 0.056) or PBF (p = 0.609). Uncorrected genotype associations were detected between STAT-rs8069645 (p = 0.0052) and ADIPOQ-rs266729 (p = 0.019) with differences in average sleep duration. Evidence for uncorrected gene-by-sleep interactions of the CLOCK-rs4864548 (p = 0.0039), PEMT-936108 (p = 0.016) and GHRELIN-rs696217 (p = 0.046) were found in relation to BMI z-scores but not for PBF. Our results indicate that children may have different genetic susceptibility to the effects of sleep duration on obesity. Further confirmatory studies are required in other population cohorts of different age groups. Copyright © 2017 Elsevier B.V. All rights reserved.

Data reconstruction can improve abundance index estimation: An example using Taiwanese longline data for Pacific bluefin tuna.

Directory of Open Access Journals (Sweden)

Shui-Kai Chang

Full Text Available Catch-per-unit-effort (CPUE is often the main piece of information used in fisheries stock assessment; however, the catch and effort data that are traditionally compiled from commercial logbooks can be incomplete or unreliable due to many reasons. Pacific bluefin tuna (PBF is a seasonal target species in the Taiwanese longline fishery. Since 2010, detailed catch information for each PBF has been made available through a catch documentation scheme. However, previously, only market landing data with a low coverage of logbooks were available. Therefore, several nontraditional procedures were performed to reconstruct catch and effort data from many alternative data sources not directly obtained from fishers for 2001-2015: (1 Estimating the catch number from the landing weight for 2001-2003, for which the catch number information was incomplete, based on Monte Carlo simulation; (2 deriving fishing days for 2007-2009 from voyage data recorder data, based on a newly developed algorithm; and (3 deriving fishing days for 2001-2006 from vessel trip information, based on linear relationships between fishing and at-sea days. Subsequently, generalized linear mixed models were developed with the delta-lognormal assumption for standardizing the CPUE calculated from the reconstructed data, and three-stage model evaluation was performed using (1 Akaike and Bayesian information criteria to determine the most favorable variable composition of standardization models, (2 overall R2 via cross-validation to compare fitting performance between area-separated and area-combined standardizations, and (3 system-based testing to explore the consistency of the standardized CPUEs with auxiliary data in the PBF stock assessment model. The last stage of evaluation revealed high consistency among the data, thus demonstrating improvements in data reconstruction for estimating the abundance index, and consequently the stock assessment.

Prenatal Stress, Methylation in Inflammation-Related Genes, and Adiposity Measures in Early Childhood: the Programming Research in Obesity, Growth Environment and Social Stress Cohort Study.

Science.gov (United States)

Wu, Shaowei; Gennings, Chris; Wright, Rosalind J; Wilson, Ander; Burris, Heather H; Just, Allan C; Braun, Joseph M; Svensson, Katherine; Zhong, Jia; Brennan, Kasey J M; Dereix, Alexandra; Cantoral, Alejandra; Schnaas, Lourdes; Téllez-Rojo, Martha Maria; Wright, Robert O; Baccarelli, Andrea A

2018-01-01

Maternal stress during pregnancy may influence childhood growth and adiposity, possibly through immune/inflammatory programming. We investigated whether exposure to prenatal stress and methylation in inflammation-related genes were associated with childhood adiposity in 424 mother-child pairs in Mexico City, Mexico. A stress index was created based on four prenatally administered stress-related scales (Exposure to Violence, Crisis in Family Systems, State-Trait Anxiety Inventory, and Edinburgh Postnatal Depression Scale). We measured weight, height, body fat mass (BFM), percentage body fat (PBF), and waist circumference in early childhood (age range, 4-6 years). Body mass index (BMI) z scores were calculated according to World Health Organization standards. DNA methylation in gene promoters of tumor necrosis factor α, interleukin 8, and interleukin 6 (IL6) in umbilical cord blood were determined by pyrosequencing. An interquartile range increase in stress index (27.3) was associated with decreases of 0.14 unit in BMI z score (95% confidence interval [CI] = -0.28 to -0.005), 5.6% in BFM (95% CI = -9.7 to -1.4), 3.5% in PBF (95% CI = -6.3 to -0.5), and 1.2% in waist circumference (95% CI = -2.4 to -0.04) in multivariable-adjusted models. An interquartile range increase in IL6 methylation (3.9%) was associated with increases of 0.23 unit in BMI z score (95% CI = 0.06-0.40), 8.1% (95% CI = 2.3-14.3) in BFM, 5.5% (95% CI = 1.7-9.5) in PBF, and 1.7% (95% CI = 0.2-3.3) in waist circumference. Prenatal stress was associated with decreased childhood adiposity, whereas cord blood IL6 methylation was associated with increased childhood adiposity in Mexican children.

O Programa Bolsa Família e os Pobres "Não Merecedores": poder discricionário e os limites da consolidação de direitos sociais

NARCIS (Netherlands)

Eiró de Oliveira, F.H.

2017-01-01

Sendo o maior programa de transferência condicionada de renda do mundo (em número absoluto de pessoas assistidas), o impacto do Programa Bolsa Família (PBF) vai além da redução de vulnerabilidades materiais. Em minhas pesquisas, constatei que o programa pode representar o único contato positivo das

Reactivity initiated accident test series Test RIA 1-4 fuel behavior report

International Nuclear Information System (INIS)

Cook, B.A.; Martinson, Z.R.

1984-09-01

This report presents and discusses results from the final test in the Reactivity Initiated Accident (RIA) Test Series, Test RIA 1-4, conducted in the Power Burst Facility (PBF) at the Idaho National Engineering Laboratory. Nine preirradiated fuel rods in a 3 x 3 bundle configuration were subjected to a power burst while at boiling water reactor hot-startup system conditions. The test resulted in estimated axial peak, radial average fuel enthalpies of 234 cal/g UO 2 on the center rod, 255 cal/g UO 2 on the side rods, and 277 cal/g UO 2 on the corner rods. Test RIA 1-4 was conducted to investigate fuel coolability and channel blockage within a bundle of preirradiated rods near the present enthalpy limit of 280 cal/g UO 2 established by the US Nuclear Regulatory Commission. The test design and conduct are described, and the bundle and individual rod thermal and mechanical responses are evaluated. Conclusions from this final test and the entire PBF RIA Test Series are presented

Estimation of regional intrapulmonary moisture volumes by pulmonary CT numbers in CT views

International Nuclear Information System (INIS)

Nakamoto, Takaaki; Kato, Shiro; Yoshimura, Masaharu

1987-01-01

In order to study the regional intrapulmonary moisture volume in normal lungs, lungs with congestion, and lungs with increased blood flow, a series of 42 subjects underwent transverse computed tomography (CT) scanning performed at a total of 17 points corresponding to the upper (7), middle (3), and lower (7) lung fields. The subjects were divided into group I (n = 24, with left-sided heart failure), group II (n = 8, with left-to-right shunt heart disease), and group III (n = 10, normals). In group I, the pulmonary peripheral minus CT numbers were inversely correlated with the pulmonary wedge mean pressure and pulmonary arterial mean pressure; and were linearly correlated with pulmonary blood flow (PBF). In group II, they were inversely correlated with PBF and left-to-right shunt volume. The pulmonary pheripheral CT numbers were significantly higher in both groups I and II than group III. In group III, these CT numbers were higher in the posterior field than the anterior field in supine position. (Hou, H.L.)

PHOTOSYNTHESIS

Energy Technology Data Exchange (ETDEWEB)

Bryant, Donald A. [Pennsylvania State Univ., University Park, PA (United States)

2002-06-21

The Gordon Research Conference (GRC) on PHOTOSYNTHESIS was held at Roger Williams University, Bristol, RI. Emphasis was placed on current unpublished research and discussion of the future target areas in this field.

Performance and Facility Background Pressure Characterization Tests of NASAs 12.5-kW Hall Effect Rocket with Magnetic Shielding Thruster

Science.gov (United States)

Kamhawi, Hani; Huang, Wensheng; Haag, Thomas; Shastry, Rohit; Thomas, Robert; Yim, John; Herman, Daniel; Williams, George; Myers, James; Hofer, Richard;

Purification process of uranium hexafluoride containing traces of plutonium fluoride and/or neptunium fluoride

International Nuclear Information System (INIS)

Aubert, J.; Bethuel, L.; Carles, M.

1983-01-01

In this process impure uranium hexafluoride is contacted with a metallic fluoride chosen in the group containing lead fluoride PbF 2 , uranium fluorides UFsub(4+x) (0 3 at a temperature such as plutonium and/or neptunium are reduced and pure uranium hexafluoride is recovered. Application is made to uranium hexafluoride purification in spent fuel reprocessing [fr

Recent study of nanomaterials prepared by inert gas condensation ...

Indian Academy of Sciences (India)

ITO), ZnO, Al2O3, Ag2O, CdO, CuO, ZnSe:ZnO etc., were prepared by this technique and characterized. Results of some of these materials will be presented in this paper. In solid-state 207Pb NMR on PbF2 a separate signal due to the presence ...

Fabrication Of Hybird Gas Turbine Disk Material System By Additive Manufacturing Project

Data.gov (United States)

National Aeronautics and Space Administration — AM offers the potential to be revolutionary for GRC hybrid disk concept as it: i) bypasses joining through direct deposition or “building” of the PX bore...

Speckle imaging algorithms for planetary imaging

Energy Technology Data Exchange (ETDEWEB)

Johansson, E. [Lawrence Livermore National Lab., CA (United States)

1994-11-15

I will discuss the speckle imaging algorithms used to process images of the impact sites of the collision of comet Shoemaker-Levy 9 with Jupiter. The algorithms use a phase retrieval process based on the average bispectrum of the speckle image data. High resolution images are produced by estimating the Fourier magnitude and Fourier phase of the image separately, then combining them and inverse transforming to achieve the final result. I will show raw speckle image data and high-resolution image reconstructions from our recent experiment at Lick Observatory.

Air Breathing Propulsion Controls and Diagnostics Research at NASA Glenn Under NASA Aeronautics Research Mission Programs

Science.gov (United States)

Garg, Sanjay

2014-01-01

This lecture will provide an overview of the aircraft turbine engine control research at NASA (National Aeronautics and Space Administration) Glenn Research Center (GRC). A brief introduction to the engine control problem is first provided with a description of the current state-of-the-art control law structure. A historical aspect of engine control development since the 1940s is then provided with a special emphasis on the contributions of GRC. The traditional engine control problem has been to provide a means to safely transition the engine from one steady-state operating point to another based on the pilot throttle inputs. With the increased emphasis on aircraft safety, enhanced performance and affordability, and the need to reduce the environmental impact of aircraft, there are many new challenges being faced by the designers of aircraft propulsion systems. The Controls and Dynamics Branch (CDB) at GRC is leading and participating in various projects in partnership with other organizations within GRC and across NASA, other government agencies, the U.S. aerospace industry, and academia to develop advanced propulsion controls and diagnostics technologies that will help meet the challenging goals of NASA programs under the Aeronautics Research Mission. The second part of the lecture provides an overview of the various CDB technology development activities in aircraft engine control and diagnostics, both current and some accomplished in the recent past. The motivation for each of the research efforts, the research approach, technical challenges and the key progress to date are summarized. The technologies to be discussed include system level engine control concepts, gas path diagnostics, active component control, and distributed engine control architecture. The lecture will end with a futuristic perspective of how the various current technology developments will lead to an Intelligent and Autonomous Propulsion System requiring none to very minimum pilot interface

Aircraft Turbine Engine Control Research at NASA Glenn Research Center

Science.gov (United States)

Garg, Sanjay

2014-01-01

This lecture will provide an overview of the aircraft turbine engine control research at NASA (National Aeronautics and Space Administration) Glenn Research Center (GRC). A brief introduction to the engine control problem is first provided with a description of the current state-of-the-art control law structure. A historical aspect of engine control development since the 1940s is then provided with a special emphasis on the contributions of GRC. The traditional engine control problem has been to provide a means to safely transition the engine from one steady-state operating point to another based on the pilot throttle inputs. With the increased emphasis on aircraft safety, enhanced performance and affordability, and the need to reduce the environmental impact of aircraft, there are many new challenges being faced by the designers of aircraft propulsion systems. The Controls and Dynamics Branch (CDB) at GRC is leading and participating in various projects in partnership with other organizations within GRC and across NASA, other government agencies, the U.S. aerospace industry, and academia to develop advanced propulsion controls and diagnostics technologies that will help meet the challenging goals of NASA programs under the Aeronautics Research Mission. The second part of the lecture provides an overview of the various CDB technology development activities in aircraft engine control and diagnostics, both current and some accomplished in the recent past. The motivation for each of the research efforts, the research approach, technical challenges and the key progress to date are summarized. The technologies to be discussed include system level engine control concepts, gas path diagnostics, active component control, and distributed engine control architecture. The lecture will end with a futuristic perspective of how the various current technology developments will lead to an Intelligent and Autonomous Propulsion System requiring none to very minimum pilot interface

Retinal Imaging and Image Analysis

Science.gov (United States)

Abràmoff, Michael D.; Garvin, Mona K.; Sonka, Milan

2011-01-01

Many important eye diseases as well as systemic diseases manifest themselves in the retina. While a number of other anatomical structures contribute to the process of vision, this review focuses on retinal imaging and image analysis. Following a brief overview of the most prevalent causes of blindness in the industrialized world that includes age-related macular degeneration, diabetic retinopathy, and glaucoma, the review is devoted to retinal imaging and image analysis methods and their clinical implications. Methods for 2-D fundus imaging and techniques for 3-D optical coherence tomography (OCT) imaging are reviewed. Special attention is given to quantitative techniques for analysis of fundus photographs with a focus on clinically relevant assessment of retinal vasculature, identification of retinal lesions, assessment of optic nerve head (ONH) shape, building retinal atlases, and to automated methods for population screening for retinal diseases. A separate section is devoted to 3-D analysis of OCT images, describing methods for segmentation and analysis of retinal layers, retinal vasculature, and 2-D/3-D detection of symptomatic exudate-associated derangements, as well as to OCT-based analysis of ONH morphology and shape. Throughout the paper, aspects of image acquisition, image analysis, and clinical relevance are treated together considering their mutually interlinked relationships. PMID:22275207

ImageX: new and improved image explorer for astronomical images and beyond

Science.gov (United States)

Hayashi, Soichi; Gopu, Arvind; Kotulla, Ralf; Young, Michael D.

2016-08-01

The One Degree Imager - Portal, Pipeline, and Archive (ODI-PPA) has included the Image Explorer interactive image visualization tool since it went operational. Portal users were able to quickly open up several ODI images within any HTML5 capable web browser, adjust the scaling, apply color maps, and perform other basic image visualization steps typically done on a desktop client like DS9. However, the original design of the Image Explorer required lossless PNG tiles to be generated and stored for all raw and reduced ODI images thereby taking up tens of TB of spinning disk space even though a small fraction of those images were being accessed by portal users at any given time. It also caused significant overhead on the portal web application and the Apache webserver used by ODI-PPA. We found it hard to merge in improvements made to a similar deployment in another project's portal. To address these concerns, we re-architected Image Explorer from scratch and came up with ImageX, a set of microservices that are part of the IU Trident project software suite, with rapid interactive visualization capabilities useful for ODI data and beyond. We generate a full resolution JPEG image for each raw and reduced ODI FITS image before producing a JPG tileset, one that can be rendered using the ImageX frontend code at various locations as appropriate within a web portal (for example: on tabular image listings, views allowing quick perusal of a set of thumbnails or other image sifting activities). The new design has decreased spinning disk requirements, uses AngularJS for the client side Model/View code (instead of depending on backend PHP Model/View/Controller code previously used), OpenSeaDragon to render the tile images, and uses nginx and a lightweight NodeJS application to serve tile images thereby significantly decreasing the Time To First Byte latency by a few orders of magnitude. We plan to extend ImageX for non-FITS images including electron microscopy and radiology scan

Low Temperature Shape Memory Alloys for Adaptive, Autonomous Systems

Data.gov (United States)

National Aeronautics and Space Administration — The objective of this joint activity between Kennedy Space Center (KSC) and Glenn Research Center (GRC) is to develop and evaluate the applicability of 2-way SMAs in...

HiVHAc Thruster Wear and Structural Tests

Data.gov (United States)

National Aeronautics and Space Administration — NASA GRC is developing a 4.5 kW-class Hall propulsion system. This system includes a long life high performance Hall Effect Thruster (HET), a highly efficient...

Advanced Manifolds for Improved Solid Oxide Electrolyzer Performance

Data.gov (United States)

National Aeronautics and Space Administration — In late 2013 NASA GRC proposed an in-situ resource utilization (ISRU) experiment on the Mars 2020 rover mission. This proposal was one of the two highest‐rated...

Mammalian DNA Repair. Final Report

Energy Technology Data Exchange (ETDEWEB)

Wood, Richard D.

2003-01-24

The Gordon Research Conference (GRC) on Mammalian DNA Repair was held at Harbortown Resort, Ventura Beach, CA. Emphasis was placed on current unpublished research and discussion of the future target areas in this field.

Imaging system design and image interpolation based on CMOS image sensor

Science.gov (United States)

Li, Yu-feng; Liang, Fei; Guo, Rui

2009-11-01

An image acquisition system is introduced, which consists of a color CMOS image sensor (OV9620), SRAM (CY62148), CPLD (EPM7128AE) and DSP (TMS320VC5509A). The CPLD implements the logic and timing control to the system. SRAM stores the image data, and DSP controls the image acquisition system through the SCCB (Omni Vision Serial Camera Control Bus). The timing sequence of the CMOS image sensor OV9620 is analyzed. The imaging part and the high speed image data memory unit are designed. The hardware and software design of the image acquisition and processing system is given. CMOS digital cameras use color filter arrays to sample different spectral components, such as red, green, and blue. At the location of each pixel only one color sample is taken, and the other colors must be interpolated from neighboring samples. We use the edge-oriented adaptive interpolation algorithm for the edge pixels and bilinear interpolation algorithm for the non-edge pixels to improve the visual quality of the interpolated images. This method can get high processing speed, decrease the computational complexity, and effectively preserve the image edges.

Security for a Smarter Planet

Science.gov (United States)

Nagaratnam, Nataraj

Bit by bit, our planet is getting smarter. By this, we mean the systems that run, the way we live and work as a society. Three things have brought this about - the world is becoming instrumented, interconnected and intelligent. Given the planet is becoming instrumented and interconnected, this opens up more risks that need to be managed. Escalating security and privacy concerns along with a renewed focus on organizational oversight are driving governance, risk management and compliance (GRC) to the forefront of the business. Compliance regulations have increasingly played a larger role by attempting to establish processes and controls that mitigate the internal and external risks organizations have today. To effectively meet the requirements of GRC, companies must prove that they have strong and consistent controls over who has access to critical applications and data.

2013 POLAR MARINE SCIENCE GORDON RESEARCH CONFERENCE AND GORDON RESEARCH SEMINAR (MARCH 10-15, 2013 - FOUR POINTS SHERATON, VENTURA CA)

Energy Technology Data Exchange (ETDEWEB)

Bowman, Jeff S.

2012-12-15

As dynamic and thermodynamic processes associated with warming trends are impacting sea ice cover, oceanographic processes and atmosphere-ocean interactions across polar regions at unprecedented rate, observations and models show fundamentally different regional ecosystem responses. The non-linear and multi-directional biogeochemical responses of polar systems to atmospheric and oceanographic forcings emphasize the need to consider and reconcile observations and models at global and regional scales. The 9th GRC on Polar Marine Science will discuss recent developments and challenges emerging from contemporary and paleo-climate observations and models, encompassing regional and global scales. The GRC addresses the structure, functionalities and controls of polar marine systems through topics such as sea ice biogeochemistry, atmosphere-ocean forcings and interactions, food web trophodynamics, carbon and elemental cycling and fluxes, and a spectrum of ecological processes and interactions.

Comparison of percentage body fat and body mass index for the prediction of inflammatory and atherogenic lipid risk profiles in elderly women

Directory of Open Access Journals (Sweden)

Funghetto SS

2015-01-01

Full Text Available Silvana Schwerz Funghetto,1 Alessandro de Oliveira Silva,2 Nuno Manuel Frade de Sousa,3 Marina Morato Stival,1 Ramires Alsamir Tibana,4 Leonardo Costa Pereira,1 Marja Letícia Chaves Antunes,1 Luciano Ramos de Lima,1 Jonato Prestes,4 Ricardo Jacó Oliveira,1 Maurílio Tiradentes Dutra,2 Vinícius Carolino Souza,1,4 Dahan da Cunha Nascimento,4 Margô Gomes de Oliveira Karnikowski1 1University of Brasília (UnB, Brasília, DF, Brazil; 2Center University of Brasilia (UNICEUB, Brasilia, DF, Brazil; 3Laboratory of Exercise Physiology, Faculty Estácio de Sá of Vitória, ES, Brazil; 4Catholic University of Brasília, Brasília, DF, Brazil Objective: To compare the clinical classification of the body mass index (BMI and percentage body fat (PBF for the prediction of inflammatory and atherogenic lipid profile risk in older women.Method: Cross-sectional analytical study with 277 elderly women from a local community in the Federal District, Brazil. PBF and fat-free mass (FFM were determined by dual energy X-ray absorptiometry. The investigated inflammatory parameters were interleukin 6 and C-reactive protein.Results: Twenty-five percent of the elderly women were classified as normal weight, 50% overweight, and 25% obese by the BMI. The obese group had higher levels of triglycerides and very low-density lipoproteins than did the normal weight group (P≤0.05 and lower levels of high-density lipoproteins (HDL than did the overweight group (P≤0.05. According to the PBF, 49% of the elderly women were classified as eutrophic, 28% overweight, and 23% obese. In the binomial logistic regression analyses including age, FFM, and lipid profile, only FFM (odds ratio [OR]=0.809, 95% confidence interval [CI]: 0.739–0.886; P<0.0005 proved to be a predictor of reaching the eutrophic state by the BMI. When the cutoff points of PBF were used for the classification, FFM (OR=0.903, CI=0.884–0.965; P=0.003 and the total cholesterol/HDL ratio (OR=0.113, CI=0.023–0

Image registration via optimization over disjoint image regions

Science.gov (United States)

Pitts, Todd; Hathaway, Simon; Karelitz, David B.; Sandusky, John; Laine, Mark Richard

2018-02-06

Technologies pertaining to registering a target image with a base image are described. In a general embodiment, the base image is selected from a set of images, and the target image is an image in the set of images that is to be registered to the base image. A set of disjoint regions of the target image is selected, and a transform to be applied to the target image is computed based on the optimization of a metric over the selected set of disjoint regions. The transform is applied to the target image so as to register the target image with the base image.

Atomic and Molecular Interactions

International Nuclear Information System (INIS)

2002-01-01

The Gordon Research Conference (GRC) on Atomic and Molecular Interactions was held at Roger Williams University, Bristol, RI. Emphasis was placed on current unpublished research and discussion of the future target areas in this field

Image processing with ImageJ

CERN Document Server

Pascau, Javier

2013-01-01

The book will help readers discover the various facilities of ImageJ through a tutorial-based approach.This book is targeted at scientists, engineers, technicians, and managers, and anyone who wishes to master ImageJ for image viewing, processing, and analysis. If you are a developer, you will be able to code your own routines after you have finished reading this book. No prior knowledge of ImageJ is expected.

Ultrasonic image analysis and image-guided interventions.

Science.gov (United States)

Noble, J Alison; Navab, Nassir; Becher, H

2011-08-06

The fields of medical image analysis and computer-aided interventions deal with reducing the large volume of digital images (X-ray, computed tomography, magnetic resonance imaging (MRI), positron emission tomography and ultrasound (US)) to more meaningful clinical information using software algorithms. US is a core imaging modality employed in these areas, both in its own right and used in conjunction with the other imaging modalities. It is receiving increased interest owing to the recent introduction of three-dimensional US, significant improvements in US image quality, and better understanding of how to design algorithms which exploit the unique strengths and properties of this real-time imaging modality. This article reviews the current state of art in US image analysis and its application in image-guided interventions. The article concludes by giving a perspective from clinical cardiology which is one of the most advanced areas of clinical application of US image analysis and describing some probable future trends in this important area of ultrasonic imaging research.

Imaging windows for long-term intravital imaging

Science.gov (United States)

Alieva, Maria; Ritsma, Laila; Giedt, Randy J; Weissleder, Ralph; van Rheenen, Jacco

2014-01-01

Intravital microscopy is increasingly used to visualize and quantitate dynamic biological processes at the (sub)cellular level in live animals. By visualizing tissues through imaging windows, individual cells (e.g., cancer, host, or stem cells) can be tracked and studied over a time-span of days to months. Several imaging windows have been developed to access tissues including the brain, superficial fascia, mammary glands, liver, kidney, pancreas, and small intestine among others. Here, we review the development of imaging windows and compare the most commonly used long-term imaging windows for cancer biology: the cranial imaging window, the dorsal skin fold chamber, the mammary imaging window, and the abdominal imaging window. Moreover, we provide technical details, considerations, and trouble-shooting tips on the surgical procedures and microscopy setups for each imaging window and explain different strategies to assure imaging of the same area over multiple imaging sessions. This review aims to be a useful resource for establishing the long-term intravital imaging procedure. PMID:28243510

Integrated Multidisciplinary Optimization Objects, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — During Phase I, M4 Engineering integrated a prototype system into OpenMDAO, a NASA GRC open-source framework. This prototype system was a proof-of-concept that M4...

Improved image alignment method in application to X-ray images and biological images.

Science.gov (United States)

Wang, Ching-Wei; Chen, Hsiang-Chou

2013-08-01

Alignment of medical images is a vital component of a large number of applications throughout the clinical track of events; not only within clinical diagnostic settings, but prominently so in the area of planning, consummation and evaluation of surgical and radiotherapeutical procedures. However, image registration of medical images is challenging because of variations on data appearance, imaging artifacts and complex data deformation problems. Hence, the aim of this study is to develop a robust image alignment method for medical images. An improved image registration method is proposed, and the method is evaluated with two types of medical data, including biological microscopic tissue images and dental X-ray images and compared with five state-of-the-art image registration techniques. The experimental results show that the presented method consistently performs well on both types of medical images, achieving 88.44 and 88.93% averaged registration accuracies for biological tissue images and X-ray images, respectively, and outperforms the benchmark methods. Based on the Tukey's honestly significant difference test and Fisher's least square difference test tests, the presented method performs significantly better than all existing methods (P ≤ 0.001) for tissue image alignment, and for the X-ray image registration, the proposed method performs significantly better than the two benchmark b-spline approaches (P < 0.001). The software implementation of the presented method and the data used in this study are made publicly available for scientific communities to use (http://www-o.ntust.edu.tw/∼cweiwang/ImprovedImageRegistration/). cweiwang@mail.ntust.edu.tw.

scikit-image: image processing in Python.

Science.gov (United States)

van der Walt, Stéfan; Schönberger, Johannes L; Nunez-Iglesias, Juan; Boulogne, François; Warner, Joshua D; Yager, Neil; Gouillart, Emmanuelle; Yu, Tony

2014-01-01

scikit-image is an image processing library that implements algorithms and utilities for use in research, education and industry applications. It is released under the liberal Modified BSD open source license, provides a well-documented API in the Python programming language, and is developed by an active, international team of collaborators. In this paper we highlight the advantages of open source to achieve the goals of the scikit-image library, and we showcase several real-world image processing applications that use scikit-image. More information can be found on the project homepage, http://scikit-image.org.

scikit-image: image processing in Python

Directory of Open Access Journals (Sweden)

Stéfan van der Walt

2014-06-01

Full Text Available scikit-image is an image processing library that implements algorithms and utilities for use in research, education and industry applications. It is released under the liberal Modified BSD open source license, provides a well-documented API in the Python programming language, and is developed by an active, international team of collaborators. In this paper we highlight the advantages of open source to achieve the goals of the scikit-image library, and we showcase several real-world image processing applications that use scikit-image. More information can be found on the project homepage, http://scikit-image.org.

The phylogeny of Myxosporea (Myxozoa) based on small subunit ribosomal RNA gene analysis

Czech Academy of Sciences Publication Activity Database

Fiala, Ivan

2006-01-01

Roč. 36, č. 14 (2006), s. 1521-1534 ISSN 0020-7519 R&D Projects: GA MŠk LC522 Grant - others:Grantová agentura Jihočeské univerzity(CZ) 58/2002//P-BF Institutional research plan: CEZ:AV0Z60220518 Keywords : Myxosporea * SSU rDNA * phylogeny Subject RIV: EB - Genetics ; Molecular Biology Impact factor: 3.337, year: 2006

Automatic UAV Image Geo-Registration by Matching UAV Images to Georeferenced Image Data

Directory of Open Access Journals (Sweden)

Xiangyu Zhuo

2017-04-01

Full Text Available Recent years have witnessed the fast development of UAVs (unmanned aerial vehicles. As an alternative to traditional image acquisition methods, UAVs bridge the gap between terrestrial and airborne photogrammetry and enable flexible acquisition of high resolution images. However, the georeferencing accuracy of UAVs is still limited by the low-performance on-board GNSS and INS. This paper investigates automatic geo-registration of an individual UAV image or UAV image blocks by matching the UAV image(s with a previously taken georeferenced image, such as an individual aerial or satellite image with a height map attached or an aerial orthophoto with a DSM (digital surface model attached. As the biggest challenge for matching UAV and aerial images is in the large differences in scale and rotation, we propose a novel feature matching method for nadir or slightly tilted images. The method is comprised of a dense feature detection scheme, a one-to-many matching strategy and a global geometric verification scheme. The proposed method is able to find thousands of valid matches in cases where SIFT and ASIFT fail. Those matches can be used to geo-register the whole UAV image block towards the reference image data. When the reference images offer high georeferencing accuracy, the UAV images can also be geolocalized in a global coordinate system. A series of experiments involving different scenarios was conducted to validate the proposed method. The results demonstrate that our approach achieves not only decimeter-level registration accuracy, but also comparable global accuracy as the reference images.

Organometallic Chemistry. Final Progress Report

Energy Technology Data Exchange (ETDEWEB)

Wolczanski, Peter [Cornell Univ., Ithaca, NY (United States)

2003-07-14

The Gordon Research Conference (GRC) on Organometallic Chemistry was held at Salve Regina, Newport, Rhode Island, 7/21-26/02. Emphasis was placed on current unpublished research and discussion of the future target areas in this field.

Markerless registration for image guided surgery. Preoperative image, intraoperative video image, and patient

International Nuclear Information System (INIS)

Kihara, Tomohiko; Tanaka, Yuko

1998-01-01

Real-time and volumetric acquisition of X-ray CT, MR, and SPECT is the latest trend of the medical imaging devices. A clinical challenge is to use these multi-modality volumetric information complementary on patient in the entire diagnostic and surgical processes. The intraoperative image and patient integration intents to establish a common reference frame by image in diagnostic and surgical processes. This provides a quantitative measure during surgery, for which we have been relied mostly on doctors' skills and experiences. The intraoperative image and patient integration involves various technologies, however, we think one of the most important elements is the development of markerless registration, which should be efficient and applicable to the preoperative multi-modality data sets, intraoperative image, and patient. We developed a registration system which integrates preoperative multi-modality images, intraoperative video image, and patient. It consists of a real-time registration of video camera for intraoperative use, a markerless surface sampling matching of patient and image, our previous works of markerless multi-modality image registration of X-ray CT, MR, and SPECT, and an image synthesis on video image. We think these techniques can be used in many applications which involve video camera like devices such as video camera, microscope, and image Intensifier. (author)

Image processing and recognition for biological images.

Science.gov (United States)

Uchida, Seiichi

2013-05-01

This paper reviews image processing and pattern recognition techniques, which will be useful to analyze bioimages. Although this paper does not provide their technical details, it will be possible to grasp their main tasks and typical tools to handle the tasks. Image processing is a large research area to improve the visibility of an input image and acquire some valuable information from it. As the main tasks of image processing, this paper introduces gray-level transformation, binarization, image filtering, image segmentation, visual object tracking, optical flow and image registration. Image pattern recognition is the technique to classify an input image into one of the predefined classes and also has a large research area. This paper overviews its two main modules, that is, feature extraction module and classification module. Throughout the paper, it will be emphasized that bioimage is a very difficult target for even state-of-the-art image processing and pattern recognition techniques due to noises, deformations, etc. This paper is expected to be one tutorial guide to bridge biology and image processing researchers for their further collaboration to tackle such a difficult target. © 2013 The Author Development, Growth & Differentiation © 2013 Japanese Society of Developmental Biologists.

Dilated intercellular space diameter as marker of reflux-related mucosal injury in children with chronic cough and gastro-oesophageal reflux disease.

Science.gov (United States)

Borrelli, O; Mancini, V; Thapar, N; Ribolsi, M; Emerenziani, S; de'Angelis, G; Bizzarri, B; Lindley, K J; Cicala, M

2014-04-01

The diagnostic corroboration of the relationship between gastro-oesophageal reflux disease (GERD) and chronic cough remains challenging. To compare oesophageal mucosal intercellular space diameter (ISD) in children with GERD, children with gastro-oesophageal reflux (GER)-related cough (GrC) and a control group, and to explore the relationship between baseline impedance levels and dilated ISD in children with GER-related cough. Forty children with GERD, 15 children with GrC and 12 controls prospectively underwent oesophagogastroduodenoscopy (EGD) with oesophageal biopsies taken 2-3 cm above squamocolumnar junction. ISD were quantified using transmission electron microscopy. Impedance-pH monitoring with evaluation of baseline impedance in the most distal impedance channel was performed in both patient groups. A significant difference in mean ISD values was found between GrC patients (0.9 ± 0.2 μm) and controls (0.5 ± 0.2 μm, P reflux parameter. Finally, there was no correlation between ISD and distal baseline impedance values (r:-0.35; NS). In children with reflux-related cough, dilated intercellular space diameter appears to be an objective and useful marker of oesophageal mucosal injury regardless of acid exposure, and its evaluation should be considered for those patients where the diagnosis is uncertain. In children with reflux-related cough, baseline impedance levels have no role in identifying reflux-induced oesophageal mucosal ultrastructural changes. © 2014 John Wiley & Sons Ltd.

Research and Technology 2002

Science.gov (United States)

Kim, Walter S.

2003-01-01

This report selectively summarizes NASA Glenn Research Center s research and technology accomplishments for fiscal year 2002. It comprises 166 short articles submitted by the staff scientists and engineers. The report is organized into five major sections: Aeronautics, Research and Technology, Space, Engineering and Technical Services, and Commercial Technology. A table of contents and author index have been developed to assist readers in finding articles of special interest. This report is not intended to be a comprehensive summary of all the research and technology work done over the past fiscal year. Most of the work is reported in Glenn-published technical reports, journal articles, and presentations prepared by Glenn staff and contractors. In addition, university grants have enabled faculty members and graduate students to engage in sponsored research that is reported at technical meetings or in journal articles. For each article in this report, a Glenn contact person has been identified, and where possible, a reference document is listed so that additional information can be easily obtained. The diversity of topics attests to the breadth of research and technology being pursued and to the skill mix of the staff that makes it possible. For more information about research at Glenn, visit us on the World Wide Web (http://www.grc.nasa.gov). This document is available online (http://www.grc.nasa.gov/WWW/RT). For publicly available reports, visit the Glenn Technical Report Server (http://gltrs.grc.nasa.gov/GLTRS/).

Research and Technology 2001

Science.gov (United States)

2002-01-01

This report selectively summarizes NASA Glenn Research Center's research and technology accomplishments for fiscal year 2001. It comprises 156 short articles submitted by the staff scientists and engineers. The report is organized into five major sections: Aeronautics, Research and Technology, Space, Engineering and Technical Services, and Commercial Technology. A table of contents and author index have been developed to assist readers in finding articles of special interest. This report is not intended to be a comprehensive summary of all the research and technology work done over the past fiscal year. Most of the work is reported in Glenn-published technical reports, journal articles, and presentations prepared by Glenn staff and contractors. In addition, university grants have enabled faculty members and graduate students to engage in sponsored research that is reported at technical meetings or in journal articles. For each article in this report, a Glenn contact person has been identified, and, where possible, a reference document is listed so that additional information can be easily obtained. The diversity of topics attests to the breadth of research and technology being pursued and to the skill mix of the staff that makes it possible. For more information about research at Glenn, visit us on the World Wide Web (http://www.grc.nasa.gov). This document is available online (http://www.grc.nasa.gov/www/RT). For publicly available reports, visit the Glenn Technical Report Server (http://gltrs.grc.nasa.gov/GLTRS).

Test Hardware Design for Flightlike Operation of Advanced Stirling Convertors (ASC-E3)

Science.gov (United States)

Oriti, Salvatore M.

2012-01-01

NASA Glenn Research Center (GRC) has been supporting development of the Advanced Stirling Radioisotope Generator (ASRG) since 2006. A key element of the ASRG project is providing life, reliability, and performance testing of the Advanced Stirling Convertor (ASC). For this purpose, the Thermal Energy Conversion branch at GRC has been conducting extended operation of a multitude of free-piston Stirling convertors. The goal of this effort is to generate long-term performance data (tens of thousands of hours) simultaneously on multiple units to build a life and reliability database. The test hardware for operation of these convertors was designed to permit in-air investigative testing, such as performance mapping over a range of environmental conditions. With this, there was no requirement to accurately emulate the flight hardware. For the upcoming ASC-E3 units, the decision has been made to assemble the convertors into a flight-like configuration. This means the convertors will be arranged in the dual-opposed configuration in a housing that represents the fit, form, and thermal function of the ASRG. The goal of this effort is to enable system level tests that could not be performed with the traditional test hardware at GRC. This offers the opportunity to perform these system-level tests much earlier in the ASRG flight development, as they would normally not be performed until fabrication of the qualification unit. This paper discusses the requirements, process, and results of this flight-like hardware design activity.

Test Hardware Design for Flight-Like Operation of Advanced Stirling Convertors

Science.gov (United States)

Oriti, Salvatore M.

2012-01-01

NASA Glenn Research Center (GRC) has been supporting development of the Advanced Stirling Radioisotope Generator (ASRG) since 2006. A key element of the ASRG project is providing life, reliability, and performance testing of the Advanced Stirling Convertor (ASC). For this purpose, the Thermal Energy Conversion branch at GRC has been conducting extended operation of a multitude of free-piston Stirling convertors. The goal of this effort is to generate long-term performance data (tens of thousands of hours) simultaneously on multiple units to build a life and reliability database. The test hardware for operation of these convertors was designed to permit in-air investigative testing, such as performance mapping over a range of environmental conditions. With this, there was no requirement to accurately emulate the flight hardware. For the upcoming ASC-E3 units, the decision has been made to assemble the convertors into a flight-like configuration. This means the convertors will be arranged in the dual-opposed configuration in a housing that represents the fit, form, and thermal function of the ASRG. The goal of this effort is to enable system level tests that could not be performed with the traditional test hardware at GRC. This offers the opportunity to perform these system-level tests much earlier in the ASRG flight development, as they would normally not be performed until fabrication of the qualification unit. This paper discusses the requirements, process, and results of this flight-like hardware design activity.

Gearbox Reliability Collaborative Phase 3 Gearbox 2 Test Report

Energy Technology Data Exchange (ETDEWEB)

Keller, Jonathan; Wallen, Robb

2015-06-10

Many gearboxes in wind turbines have not been achieving their expected design life [1]; they do, however, commonly meet or exceed the design criteria specified in current standards in the gear, bearing, and wind turbine industry as well as third-party certification criteria. The cost of gearbox replacements and rebuilds, as well as the downtime associated with these failures, has elevated the cost of wind energy. In 2006, the U.S. Department of Energy established the National Renewable Energy Laboratory (NREL) Gearbox Reliability Collaborative (GRC). Its key goal is to understand the root causes of premature gearbox failures and improve their reliability [2]. The GRC is examining a hypothesis that the gap between design-estimated and actual wind turbine gearbox reliability is caused by underestimation of loads, inaccurate design tools, the absence of critical elements in the design process, or insufficient testing. This test report describes the recent tests of GRC gearbox (GB) 2 in the National Wind Technology Center (NWTC) dynamometer and documents any modifications to the original test plan [3]. In this manner, it serves as a guide for interpreting the publicly released data sets with brief analyses to illustrate the data. Specific objectives of the test were to assess the effect of dynamic nontorque load (NTL) on the planetary section, generator misalignment on the highspeed shaft (HSS), and field representative conditions on the gearbox in general. Detailed analysis of those test objectives will be presented in subsequent publications.

Chemical Reactions at Surfaces. Final Progress Report

Energy Technology Data Exchange (ETDEWEB)

Freud, Hans-Joachim [Max-Planck-Gesellschaft, Berlin (Germany). Fritz-Haber-Inst.

2003-02-21

The Gordon Research Conference (GRC) on Chemical Reactions at Surfaces was held at Holiday Inn, Ventura, California, 2/16-21/03. Emphasis was placed on current unpublished research and discussion of the future target areas in this field.

IMAGE DESCRIPTIONS FOR SKETCH BASED IMAGE RETRIEVAL

OpenAIRE

SAAVEDRA RONDO, JOSE MANUEL; SAAVEDRA RONDO, JOSE MANUEL

2008-01-01

Due to the massive use of Internet together with the proliferation of media devices, content based image retrieval has become an active discipline in computer science. A common content based image retrieval approach requires that the user gives a regular image (e.g, a photo) as a query. However, having a regular image as query may be a serious problem. Indeed, people commonly use an image retrieval system because they do not count on the desired image. An easy alternative way t...

Image formation and image analysis in electron microscopy

International Nuclear Information System (INIS)

Heel, M. van.

1981-01-01

This thesis covers various aspects of image formation and image analysis in electron microscopy. The imaging of relatively strong objects in partially coherent illumination, the coherence properties of thermionic emission sources and the detection of objects in quantum noise limited images are considered. IMAGIC, a fast, flexible and friendly image analysis software package is described. Intelligent averaging of molecular images is discussed. (C.F.)

ImageSURF: An ImageJ Plugin for Batch Pixel-Based Image Segmentation Using Random Forests

Directory of Open Access Journals (Sweden)

Aidan O'Mara

2017-11-01

Full Text Available Image segmentation is a necessary step in automated quantitative imaging. ImageSURF is a macro-compatible ImageJ2/FIJI plugin for pixel-based image segmentation that considers a range of image derivatives to train pixel classifiers which are then applied to image sets of any size to produce segmentations without bias in a consistent, transparent and reproducible manner. The plugin is available from ImageJ update site http://sites.imagej.net/ImageSURF/ and source code from https://github.com/omaraa/ImageSURF. Funding statement: This research was supported by an Australian Government Research Training Program Scholarship.

High Efficiency Space Power Systems Project Advanced Space-Rated Batteries

Science.gov (United States)

Reid, Concha M.

2011-01-01

Case Western Reserve University (CWRU) has an agreement with China National Offshore Oil Corporation New Energy Investment Company, Ltd. (CNOOC), under the United States-China EcoPartnerships Framework, to create a bi-national entity seeking to develop technically feasible and economically viable solutions to energy and environmental issues. Advanced batteries have been identified as one of the initial areas targeted for collaborations. CWRU invited NASA Glenn Research Center (GRC) personnel from the Electrochemistry Branch to CWRU to discuss various aspects of advanced battery development as they might apply to this partnership. Topics discussed included: the process for the selection of a battery chemistry; the establishment of an integrated development program; project management/technical interactions; new technology developments; and synergies between batteries for automotive and space operations. Additional collaborations between CWRU and NASA GRC's Electrochemistry Branch were also discussed.

Design of a K/Q-Band Beacon Receiver for the Alphasat Technology Demonstration Payload (TDP) #5 Experiment

Science.gov (United States)

Morse, Jacquelynne R.

2014-01-01

This paper describes the design and performance of a coherent KQ-band (2040 GHz) beacon receiver developed at NASA Glenn Research Center (GRC) that will be installed at the Politecnico di Milano (POLIMI) for use in the Alphasat Technology Demonstration Payload 5 (TDP5) beacon experiment. The goal of this experiment is to characterize rain fade attenuation at 40 GHz to improve the performance of existing statistical rain attenuation models in the Q-band. The ground terminal developed by NASA GRC utilizes an FFT-based frequency estimation receiver capable of characterizing total path attenuation effects due to gaseous absorption, clouds, rain, and scintillation. The receiver system has been characterized in the lab and demonstrates a system dynamic range performance of better than 58 dB at 1 Hz and better than 48 dB at 10 Hz rates.

Design of a K/Q-Band Beacon Receiver for the Alphasat TDP#5 Experiment

Science.gov (United States)

Morse, Jacquelynne R.

2014-01-01

This paper describes the design and performance of a coherent KQ-band (2040 GHz) beacon receiver developed at NASA Glenn Research Center (GRC) that will be installed at the Politecnico di Milano (POLIMI) for use in the Alphasat Technology Demonstration Payload 5 (TDP5) beacon experiment. The goal of this experiment is to characterize rain fade attenuation at 40 GHz to improve the performance of existing statistical rain attenuation models in the Q-band. The ground terminal developed by NASA GRC utilizes an FFT-based frequency estimation receiver capable of characterizing total path attenuation effects due to gaseous absorption, clouds, rain, and scintillation. The receiver system has been characterized in the lab and demonstrates a system dynamic range performance of better than 58 dB at 1 Hz and better than 48 dB at 10 Hz rates.

Assessment of pulmonary parenchyma perfusion with FAIR in comparison with DCE-MRI-Initial results

Energy Technology Data Exchange (ETDEWEB)

Fan Li [Department of Radiology, ChangZheng Hospital Affiliated to Second Military Medical University, No. 415 Fengyang Road, Shanghai 200003 (China)], E-mail: fanli0930@163.com; Liu Shiyuan [Department of Radiology, ChangZheng Hospital Affiliated to Second Military Medical University, No. 415 Fengyang Road, Shanghai 200003 (China); Sun Fei [GE Healthcare China (China)], E-mail: Fei.sun@med.ge.com; Xiao Xiangsheng [Department of Radiology, ChangZheng Hospital Affiliated to Second Military Medical University, No. 415 Fengyang Road, Shanghai 200003 (China)], E-mail: lizhaobin79@163.com

2009-04-15

Objective: The aim of this study was to assess pulmonary parenchyma perfusion with flow-sensitive alternating inversion recovery (FAIR) in comparison with 3D dynamic contrast-enhanced (DCE) imaging in healthy volunteers and in patients with pulmonary embolism or lung cancer. Materials and methods: Sixteen healthy volunteers and 16 patients with pulmonary embolism (5 cases) or lung cancer (11 cases) were included in this study. Firstly, the optimized inversion time of FAIR (TI) was determined in 12 healthy volunteers. Then, FAIR imaging with the optimized TI was performed followed by DCE-MRI on the other 4 healthy volunteers and 16 patients. Tagging efficiency of lung and SNR of perfusion images were calculated with different TI values. In the comparison of FAIR with DCE-MRI, the homogeneity of FAIR and DCE-MRI perfusion was assessed. In the cases of perfusion abnormality, the contrast between normal lung and perfusion defects was quantified by calculating a normalized signal intensity ratio. Results: One thousand milliseconds was the optimal TI, which generated the highest lung tagging efficiency and second highest PBF SNR. In the volunteers, the signal intensity of perfusion images acquired with both FAIR and DCE-MRI was homogeneous. Wedged-shaped or triangle perfusion defects were visualized in five pulmonary embolisms and three lung cancer cases. There was no significant statistical difference in signal intensity ratio between FAIR and DCE-MRI (P > 0.05). In the rest of eight lung cancers, all the lesions showed low perfusion against the higher perfused pulmonary parenchyma in both FAIR and DCE-MRI. Conclusion: Pulmonary parenchyma perfusion imaging with FAIR was feasible, consistent and could obtain similar functional information to that from DCE-MRI.

Assessment of pulmonary parenchyma perfusion with FAIR in comparison with DCE-MRI-Initial results

International Nuclear Information System (INIS)

Fan Li; Liu Shiyuan; Sun Fei; Xiao Xiangsheng

2009-01-01

Objective: The aim of this study was to assess pulmonary parenchyma perfusion with flow-sensitive alternating inversion recovery (FAIR) in comparison with 3D dynamic contrast-enhanced (DCE) imaging in healthy volunteers and in patients with pulmonary embolism or lung cancer. Materials and methods: Sixteen healthy volunteers and 16 patients with pulmonary embolism (5 cases) or lung cancer (11 cases) were included in this study. Firstly, the optimized inversion time of FAIR (TI) was determined in 12 healthy volunteers. Then, FAIR imaging with the optimized TI was performed followed by DCE-MRI on the other 4 healthy volunteers and 16 patients. Tagging efficiency of lung and SNR of perfusion images were calculated with different TI values. In the comparison of FAIR with DCE-MRI, the homogeneity of FAIR and DCE-MRI perfusion was assessed. In the cases of perfusion abnormality, the contrast between normal lung and perfusion defects was quantified by calculating a normalized signal intensity ratio. Results: One thousand milliseconds was the optimal TI, which generated the highest lung tagging efficiency and second highest PBF SNR. In the volunteers, the signal intensity of perfusion images acquired with both FAIR and DCE-MRI was homogeneous. Wedged-shaped or triangle perfusion defects were visualized in five pulmonary embolisms and three lung cancer cases. There was no significant statistical difference in signal intensity ratio between FAIR and DCE-MRI (P > 0.05). In the rest of eight lung cancers, all the lesions showed low perfusion against the higher perfused pulmonary parenchyma in both FAIR and DCE-MRI. Conclusion: Pulmonary parenchyma perfusion imaging with FAIR was feasible, consistent and could obtain similar functional information to that from DCE-MRI.

Fast processing of foreign fiber images by image blocking

Directory of Open Access Journals (Sweden)

Yutao Wu

2014-08-01

Full Text Available In the textile industry, it is always the case that cotton products are constitutive of many types of foreign fibers which affect the overall quality of cotton products. As the foundation of the foreign fiber automated inspection, image process exerts a critical impact on the process of foreign fiber identification. This paper presents a new approach for the fast processing of foreign fiber images. This approach includes five main steps, image block, image pre-decision, image background extraction, image enhancement and segmentation, and image connection. At first, the captured color images were transformed into gray-scale images; followed by the inversion of gray-scale of the transformed images ; then the whole image was divided into several blocks. Thereafter, the subsequent step is to judge which image block contains the target foreign fiber image through image pre-decision. Then we segment the image block via OSTU which possibly contains target images after background eradication and image strengthening. Finally, we connect those relevant segmented image blocks to get an intact and clear foreign fiber target image. The experimental result shows that this method of segmentation has the advantage of accuracy and speed over the other segmentation methods. On the other hand, this method also connects the target image that produce fractures therefore getting an intact and clear foreign fiber target image.

A method of image improvement in three-dimensional imaging

International Nuclear Information System (INIS)

Suto, Yasuzo; Huang, Tewen; Furuhata, Kentaro; Uchino, Masafumi.

1988-01-01

In general, image interpolation is required when the surface configurations of such structures as bones and organs are three-dimensionally constructed from the multi-sliced images obtained by CT. Image interpolation is a processing method whereby an artificial image is inserted between two adjacent slices to make spatial resolution equal to slice resolution in appearance. Such image interpolation makes it possible to increase the image quality of the constructed three-dimensional image. In our newly-developed algorithm, we have converted the presently and subsequently sliced images to distance images, and generated the interpolation images from these two distance images. As a result, compared with the previous method, three-dimensional images with better image quality have been constructed. (author)

Integration of KESS III models in ATHLET-CD and contributions to program verification. Final report

International Nuclear Information System (INIS)

Bruder, M.; Schatz, A.

1994-07-01

The development of the computer code ATHLET-CD is a contribution to the reactor safety research. ATHLET-CD is an extension of the system code ATHLET by core degradation models especially of the modular software package KESS. The aim of the ATHLET-CD development is the simulation of severe accident sequences from their initialisation to severe core degradation in a continous manner. In the framework of this project the ATHLET-CD development has been focused on the integration of KESS model like the control rod model as well as the models describing chemical interactions and material relocation along a rod and fission product release. The present ATHLET-CD version is able to describe severe accidents in a PWR up to the early core degradation (relocation of material along a rod surface in axial direction). Contributions to the verification of ATHLET-CD comprised calculations of the experiments PHEBUS AIC and PBF SFD 1-4. The PHEBUS AIC calculation was focused on the examination of the control rod model whereas the PBF SFD 1-4 claculation served to check the models describing melting, material relocation and fission product release. (orig.)

Effects of burnup on fission product release and implications for severe fuel damage events

International Nuclear Information System (INIS)

Appelhans, A.D.; Cronenberg, A.W.; Carboneau, M.L.

1984-01-01

Xe, Kr, and I fission-product release data from (a) Halden tests where release in intact rods was measured during irradiation at burnups to 18,000 MWd/t and fuel temperatures of 800 to 1800 0 K, and (b) Power Burst Facility (PBF) tests where trace-irradiated fuel (approx. = 90 MWd/t) was driven to temperatures of >2400 0 K and fuel liquefaction occurred are discussed and related to fuel morphology. Results from both indicate that the fission-product morphology and fuel restructuring govern release behavior. The Halden tests show low release at beginning of life with a 10-fold increase at burnups in excess of 10,000 MWd/t, due to the development of grain boundary interlinkage at higher burnups. Such dependence of release on morphology characteristics is consistent with findings from the PBF tests, where for trace-irradiated fuel, the absence of interlinkage accounts for the low release rates observed during initial fuel heatup, with subsequent enhanced Xe, Kr, and I release via liquefaction or quench-induced destruction of the grain structure. Morphology is also shown to influence the chemical release form of I and Cs fission products

Chemical and enzymatic catalytic routes to polyesters and oligopeptides biobased materials

Science.gov (United States)

Zhu, Jianhui

My Ph.D research focuses on the synthesis and property studies of different biobased materials, including polyesters, polyurethanes and oligopeptides. The first study describes the synthesis, crystal structure and physico-mechanical properties of a bio-based polyester prepared from 2,5-furandicarboxylic acid (FDCA) and 1,4-butanediol. Melt-polycondensation experiments were conducted by a two-stage polymerization using titanium tetraisopropoxide (Ti[OiPr] 4) as catalyst. Polymerization conditions (catalyst concentration, reaction time and 2nd stage reaction temperature) were varied to optimize poly(butylene furan dicarboxylate), PBF, molecular weight. A series of PBFs with different Mw were characterized by Differential Scanning Calorimetry (DSC), Thermogravimetric Analysis (TGA), Dynamic Mechanical Thermal Analysis (DMTA), X-Ray diffraction and tensile testing. Influence of molecular weight and melting/crystallization enthalpy on PBF material tensile properties was explored. Cold-drawing tensile tests at room temperature for PBF with Mw 16K to 27K showed a brittle-to-ductile transition. When Mw reaches 38K, the Young's Modulus of PBF remains above 900 MPa, and the elongation at break increases to above 1000%. The mechanical properties, thermal properties and crystal structures of PBF were similar to petroleum derived poly(butylenes terephthalate), PBT. Fiber diagrams of uniaxially stretched PBF films were collected, indexed, and the unit cell was determined as triclinic (a=4.78(3) A, b=6.03(5) A, c=12.3(1) A, alpha=110.1(2)°, beta=121.1(3)°, gamma=100.6(2)°). A crystal structure was derived from this data and final atomic coordinates are reported. We concluded that there is a close similarity of the PBF structure to PBT alpha- and beta-forms. In the second study, a biobased long chain polyester polyol (PC14-OH) was synthesized from o-hydroxytetradecanoic acid (o-HOC14) and 1,4-butanediol. The first section about polyester polyurethanes describes the synthesis

Image processing with ImageJ

NARCIS (Netherlands)

Abramoff, M.D.; Magalhães, Paulo J.; Ram, Sunanda J.

2004-01-01

Wayne Rasband of NIH has created ImageJ, an open source Java-written program that is now at version 1.31 and is used for many imaging applications, including those that that span the gamut from skin analysis to neuroscience. ImageJ is in the public domain and runs on any operating system (OS).

Compositional images from the Diffraction Enhanced Imaging technique

International Nuclear Information System (INIS)

Hasnah, M.O.; Zhong, Z.; Parham, C.; Zhang, H.; Chapman, D.

2007-01-01

Diffraction Enhanced Imaging (DEI) derives X-ray contrast from absorption, refraction, and extinction. While the refraction angle image of DEI represents the gradient of the projected mass density of the object, the absorption image measures the projected attenuation (μt)-bar of an object. Using a simple integral method it has been shown that a mass density image (ρt)-bar can be obtained from the refraction angle image. It then is a simple matter to develop a combinational image by dividing these two images to create a μ/ρ image. The μ/ρ is a fundamental property of a material and is therefore useful for identifying the composition of an object. In projection X-ray imaging the μ/ρ image identifies the integrated composition of the elements along the beam path. When applied to DEI computed tomography (CT), the image identifies the composition in each voxel. This method presents a new type of spectroscopy based in radiography. We present the method of obtaining the compositional image, the results of experiments in which we verify the method with known standards and an application of the method to breast cancer imaging

Evaluation of pulmonary emphysema by the fused image of CT image and ventilation SPECT image

International Nuclear Information System (INIS)

Okuda, Ituko; Maruno, Hiromasa; Mori, Kazuaki; Kohno, Tadashi; Kokubo, Takashi

2007-01-01

We evaluated pulmonary emphysema using a diagnostic device that could obtain a CT image, a ventilation single photon emission computed tomography (SPECT) image and a lung perfusion SPECT image in one examination. The fused image made from the CT image and SPECT image had very little position gap between images, and the precision was high. From the fused image, we were able to detect the areas in which emphysematous change was the most marked in the CT image, while the accumulation decrease was most remarkable in the ventilation SPECT image. Thus it was possible to obtain an accurate status of pulmonary emphysema, and our method was regarded as a useful technique. (author)

Improving the Image Quality of Synthetic Transmit Aperture Ultrasound Images - Achieving Real-Time In-Vivo Imaging

DEFF Research Database (Denmark)

Gammelmark, Kim

in-vivo experiments, showed, that TMS imaging can increase the SNR by as much as 17 dB compared to the traditional imaging techniques, which improves the in-vivo image quality to a highly competitive level. An in-vivo evaluation of convex array TMS imaging for abdominal imaging applications......-vivo imaging, and that the obtained image quality is highly competitive with the techniques applied in current medical ultrasound scanners. Hereby, the goals of the PhD have been successfully achieved.......Synthetic transmit aperture (STA) imaging has the potential to increase the image quality of medical ultrasound images beyond the levels obtained by conventional imaging techniques (linear, phased, and convex array imaging). Currently, however, in-vivo applications of STA imaging is limited...

Electron Donor Acceptor Interactions. Final Progress Report

Energy Technology Data Exchange (ETDEWEB)

Moore, Ana L. [Arizona State Univ., Tempe, AZ (United States)

2002-08-16

The Gordon Research Conference (GRC) on Electron Donor Acceptor Interactions was held at Salve Regina University, Newport, Rhode Island, 8/11-16/02. Emphasis was placed on current unpublished research and discussion of the future target areas in this field.

VESGEN Mapping of Bioactive Protection against Intestinal Inflammation: Application to Human Spaceflight and ISS Experiments

Science.gov (United States)

Parsons-Wingerter, P. A.; Chen, X.; Kelly, C. P.; Reinecker, H. C.

2011-01-01

Challenges to successful space exploration and colonization include adverse physiological reactions to micro gravity and space radiation factors. Constant remodeling of the microvasculature is critical for tissue preservation, wound healing, and recovery after ischemia. Regulation of the vascular system in the intestine is particularly important to enable nutrient absorption while maintaining barrier function and mucosal defense against micro biota. Although tremendous progress has been made in understanding the molecular circuits regulating neovascularization, our knowledge of the adaptations of the vascular system to environmental challenges in the intestine remains incomplete. This is in part because of the lack of methods to observe and quantify the complex processes associated with vascular responses in vivo. Developed by GRC as a mature beta version, pre-release research software, VESsel GENeration Analysis (VESGEN) maps and quantifies the fractal-based complexity of vascular branching for novel insights into the cytokine, transgenic and therapeutic regulation of angiogenesis, lymphangiogenesis and microvascular remodeling. Here we demonstrate that VESGEN can be used to characterize the dynamic vascular responses to acute intestinal inflammation and mucosal recovery from in vivo confocal microscopic 3D image series. We induced transient intestinal inflammation in mice by DSS treatment and investigated whether the ability of the pro biotic yeast Saccharomyces boulardii (Sb) to protect against intestinal inflammation was due to regulation of vascular remodeling. A primary characteristic of inflammation is excessive neovascularization (angiogenesis) resulting in fragile vessels prone to bleeding. Morphological parameters for triplicate specimens revealed that Sb treatment greatly reduced the inflammatory response of vascular networks by an average of 78%. This resulted from Sb inhibition of vascular endothelial growth factor receptor signaling, a major

Library Services Funding Assessment

Science.gov (United States)

Lorig, Jonathan A.

2004-01-01

The Glenn Technical Library is a science and engineering library that primarily supports research activities at the Glenn Research Center, and provides selected services to researchers at all of the NASA research centers. Resources available in the library include books, journals, CD-ROMs, and access to various online sources, as well as live reference and inter-library loan services. The collection contains over 77,000 books, 800,000 research reports, and print or online access to over 1,400 journals. Currently the library operates within the Logistics and Technical Information Division, and is funded as an open-access resource within the GRC. Some of the research units at the GRC have recently requested that the library convert to a "pay-for-services" model, in which individual research units could fund only those journal subscriptions for which they have a specific need. Under this model, the library would always maintain a certain minimum level of pooled-expense services, including the ready reference and book collections, and inter-library loan services. Theoretically the "pay-for-services" model would encourage efficient financial allocation, and minimize the extent to which paid journal subscriptions go unused. However, this model also could potentially negate the benefits of group purchases for journal subscriptions and access. All of the major journal publishers offer package subscriptions that compare favorably in cost with the sum of individual subscription costs for a similar selection of titles. Furthermore, some of these subscription packages are "consortium" purchases that are funded collectively by the libraries at multiple NASA research centers; such consortia1 memberships would be difficult for the library to pay, if enough GRC research units were to withdraw their pooled contributions. cost of collectively-funded journal access with the cost of individual subscriptions. My primary task this summer is to create the cost dataset framework, and

Nuclear medicine imaging instrumentations for molecular imaging

International Nuclear Information System (INIS)

Chung, Yong Hyun; Song, Tae Yong; Choi, Yong

2004-01-01

Small animal models are extensively utilized in the study of biomedical sciences. Current animal experiments and analysis are largely restricted to in vitro measurements and need to sacrifice animals to perform tissue or molecular analysis. This prevents researchers from observing in vivo the natural evolution of the process under study. Imaging techniques can provide repeatedly in vivo anatomic and molecular information noninvasively. Small animal imaging systems have been developed to assess biological process in experimental animals and increasingly employed in the field of molecular imaging studies. This review outlines the current developments in nuclear medicine imaging instrumentations including fused multi-modality imaging systems for small animal imaging

Image registration of naval IR images

Science.gov (United States)

Rodland, Arne J.

1996-06-01

In a real world application an image from a stabilized sensor on a moving platform will not be 100 percent stabilized. There will always be a small unknown error in the stabilization due to factors such as dynamic deformations in the structure between sensor and reference Inertial Navigation Unit, servo inaccuracies, etc. For a high resolution imaging sensor this stabilization error causes the image to move several pixels in unknown direction between frames. TO be able to detect and track small moving objects from such a sensor, this unknown movement of the sensor image must be estimated. An algorithm that searches for land contours in the image has been evaluated. The algorithm searches for high contrast points distributed over the whole image. As long as moving objects in the scene only cover a small area of the scene, most of the points are located on solid ground. By matching the list of points from frame to frame, the movement of the image due to stabilization errors can be estimated and compensated. The point list is searched for points with diverging movement from the estimated stabilization error. These points are then assumed to be located on moving objects. Points assumed to be located on moving objects are gradually exchanged with new points located in the same area. Most of the processing is performed on the list of points and not on the complete image. The algorithm is therefore very fast and well suited for real time implementation. The algorithm has been tested on images from an experimental IR scanner. Stabilization errors were added artificially to the image such that the output from the algorithm could be compared with the artificially added stabilization errors.

Risk-based decision making to manage water quality failures caused by combined sewer overflows

Science.gov (United States)

Sriwastava, A. K.; Torres-Matallana, J. A.; Tait, S.; Schellart, A.

2017-12-01

Regulatory authorities set certain environmental permit for water utilities such that the combined sewer overflows (CSO) managed by these companies conform to the regulations. These utility companies face the risk of paying penalty or negative publicity in case they breach the environmental permit. These risks can be addressed by designing appropriate solutions such as investing in additional infrastructure which improve the system capacity and reduce the impact of CSO spills. The performance of these solutions is often estimated using urban drainage models. Hence, any uncertainty in these models can have a significant effect on the decision making process. This study outlines a risk-based decision making approach to address water quality failure caused by CSO spills. A calibrated lumped urban drainage model is used to simulate CSO spill quality in Haute-Sûre catchment in Luxembourg. Uncertainty in rainfall and model parameters is propagated through Monte Carlo simulations to quantify uncertainty in the concentration of ammonia in the CSO spill. A combination of decision alternatives such as the construction of a storage tank at the CSO and the reduction in the flow contribution of catchment surfaces are selected as planning measures to avoid the water quality failure. Failure is defined as exceedance of a concentration-duration based threshold based on Austrian emission standards for ammonia (De Toffol, 2006) with a certain frequency. For each decision alternative, uncertainty quantification results into a probability distribution of the number of annual CSO spill events which exceed the threshold. For each alternative, a buffered failure probability as defined in Rockafellar & Royset (2010), is estimated. Buffered failure probability (pbf) is a conservative estimate of failure probability (pf), however, unlike failure probability, it includes information about the upper tail of the distribution. A pareto-optimal set of solutions is obtained by performing mean

Enhancement of luminescence properties in Er3+ doped TeO2-Na2O-PbX (X=O and F) ternary glasses.

Science.gov (United States)

Kumar, Kaushal; Rai, S B; Rai, D K

2007-04-01

An enhancement of luminescence properties in Er3+ doped ternary glasses is observed on the addition of PbO/PbF2. The infrared to visible upconversion emission bands are observed at 410, 525, 550 and 658 nm, due to the 2H9/2-->4I15/2, 2H11/2-->4I15/2, 4S3/2-->4I15/2, 4F9/2-->4I15/2 transitions respectively, on excitation with 797 nm laser line. A detailed study reveals that the 2H9/2-->4I15/2 transition arises due to three step upconversion process while other transitions arise due to two step absorption. On excitation with 532 nm radiation, ultraviolet and violet upconversion bands centered at 380, 404, 410 and 475 nm wavelengths are observed along with one photon luminescence bands at 525, 550, 658 and 843 nm wavelengths. These bands are found due to the 4G11/2-->4I15/2, 2P3/2-->4I13/2, 2H9/2-->4I15/2, 2P3/2-->4I11/2, 2H11/2-->4I15/2, 4S3/2-->4I15/2, 4F9/2-->4I15/2 and 4S3/2-->4I13/2 transitions, respectively. Though incorporation of PbO and PbF2 both enhances fluorescence intensities however, PbF2 content has an important influence on upconversion luminescence emission. The incorporation of PbF2 enhances the red emission (658 nm) intensity by 1.5 times and the violet emission (410 nm) intensity by 2.0 times. A concentration dependence study of fluorescence reveals the rapid increase in the red (4F9/2-->4I15/2) emission intensity relative to the green (4S3/2-->4I15/2) emission with increase in the Er3+ ion concentration. This behaviour has been explained in terms of an energy transfer by relaxation between excited ions.

Non-occupational lead and cadmium exposure of adult women in Bangkok, Thailand

International Nuclear Information System (INIS)

Zhang, Z.-W.; Shimbo, S.; Watanabe, T.; Srianujata, S.; Banjong, O.; Chitchumroonchokchai, C.; Nakatsuka, H.; Matsuda-Inoguchi, N.; Higashikawa, K.; Ikeda, M.

1999-01-01

This survey was conducted to examine the extent of the exposure of Bangkok citizens to lead (Pb) and cadmium (Cd), and to evaluate the role of rice as the source of these heavy metals. In practice, 52 non-smoking adult women in an institution in the vicinity of Bangkok, volunteered to offer blood, spot urine, boiled rice and 24-h total food duplicate samples. Samples were wet-ashed, and then analyzed for Pb and Cd by ICP-MS. Geometric means for the levels in blood (Pb-B and Cd-B) and urine (Pb-U and Cd-U as corrected for creatinine concentration), and also for dietary intake (Pb-F and Cd-F) were 32.3 μg/l for Pb-B, 0.41 μg/l for Cd-B, 2.06 μg/g creatinine for Pb-U, 1.40 μg/g creatinine for Cd-U, 15.1 μg/day for Pb-F and 7.1 μg/day for Cd-F. Rice contributed 30% and 4% of dietary Cd and Pb burden, respectively. When compared with the counterpart values obtained in four neighboring cities in southeast Asia (i.e. Nanning, Tainan, Manila, and Kuala Lumpur), dietary Pb burden of the women in Bangkok was middle in the order among the values for the five cities. Pb level in the blood was the lowest of the levels among the five cities and Pb in urine was also among the low group. This apparent discrepancy in the order between Pb-B (i.e. the fifth) and Pb-F (the third) might be attributable to recent reduction of Pb levels in the atmosphere in Bangkok. Regarding Cd exposure, Cd levels in blood and urine as well as dietary Cd burden of Bangkok women were either the lowest or the next lowest among those in the five cities. (Copyright (c) 1999 Elsevier Science B.V., Amsterdam. All rights reserved.)

Image portion identification methods, image parsing methods, image parsing systems, and articles of manufacture

Science.gov (United States)

Lassahn, Gordon D.; Lancaster, Gregory D.; Apel, William A.; Thompson, Vicki S.

2013-01-08

Image portion identification methods, image parsing methods, image parsing systems, and articles of manufacture are described. According to one embodiment, an image portion identification method includes accessing data regarding an image depicting a plurality of biological substrates corresponding to at least one biological sample and indicating presence of at least one biological indicator within the biological sample and, using processing circuitry, automatically identifying a portion of the image depicting one of the biological substrates but not others of the biological substrates.

Tomographic image reconstruction using training images

DEFF Research Database (Denmark)

Soltani, Sara; Andersen, Martin Skovgaard; Hansen, Per Christian

2017-01-01

We describe and examine an algorithm for tomographic image reconstruction where prior knowledge about the solution is available in the form of training images. We first construct a non-negative dictionary based on prototype elements from the training images; this problem is formulated within...

Image quality of digital mammography images produced using wet and dry laser imaging systems

International Nuclear Information System (INIS)

Al Khalifah, K.; Brindhaban, A.; AlArfaj, R.; Jassim, O.

2006-01-01

Introduction: A study was carried out to compare the quality of digital mammographic images printed or processed by a wet laser imaging system and a dedicated mammographic dry laser imaging system. Material and methods: Digital images of a tissue equivalent breast phantom were obtained using a GE Senographe 2000D digital mammography system and different target/filter combinations of the X-ray tube. These images were printed on films using the Fuji FL-IM D wet laser imaging system and the Kodak DryView 8600 dry laser imaging system. The quality of images was assessed in terms of detectability of microcalcifications and simulated tumour masses by five radiologists. In addition, the contrast index and speed index of the two systems were measured using the step wedge in the phantom. The unpaired, unequal variance t-test was used to test any statistically significant differences. Results: There were no significant (p < 0.05) differences between the images printed using the two systems in terms of microcalcification and tumour mass detectability. The wet system resulted in slightly higher contrast index while the dry system showed significantly higher speed index. Conclusion: Both wet and dry laser imaging systems can produce mammography images of good quality on which 0.2 mm microcalcifications and 2 mm tumour masses can be detected. Dry systems are preferable due to the absence of wet chemical processing and solid or liquid chemical waste. The wet laser imaging systems, however, still represent a useful alternative to dry laser imaging systems for mammography studies

Television Images and Adolescent Girls' Body Image Disturbance.

Science.gov (United States)

Botta, Renee A.

1999-01-01

Contributes to scholarship on the effects of media images on adolescents, using social-comparison theory and critical-viewing theory. Finds that media do have an impact on body-image disturbance. Suggests that body-image processing is the key to understanding how television images affect adolescent girls' body-image attitudes and behaviors. (SR)

AN/GRC-171 Rivet Switch Multichannel UHF/AM Transceiver

Science.gov (United States)

1975-03-01

1879CS/LGMG Arellano, Cayetno A Chief, ATC Operations 1879CS/ FFA Capt Rucker, William C. CMSgt McCallum, Duncan Control Tower Chief Contractor...9/* zs L-f-ZO 7s. to ZJ-S’ 59.9s GENERAL PURPOSE FORM AFCS iaoot/io«i . o.^...,«.., ,,,,„ i ,„„„ lIBS^pnnwWWIW^ Bpp ^BWTWRPIP»^ 4.3.15 AN

Overview of Photovoltaic Calibration and Measurement Standards at GRC

Science.gov (United States)

Baraona, Cosmo; Snyder, David; Brinker, David; Bailey, Sheila; Curtis, Henry; Scheiman, David; Jenkins, Phillip

2002-01-01

Photovoltaic (PV) systems (cells and arrays) for spacecraft power have become an international market. This market demands accurate prediction of the solar array power output in space throughout the mission life of the spacecraft. Since the beginning of space flight, space-faring nations have independently developed methods to calibrate solar cells for power output in low Earth orbit (LEO). These methods rely on terrestrial, laboratory, or extraterrestrial light sources to simulate or approximate the air mass zero (AM0) solar intensity and spectrum.

To Image...or Not to Image?

Science.gov (United States)

Bruley, Karina

1996-01-01

Provides a checklist of considerations for installing document image processing with an electronic document management system. Other topics include scanning; indexing; the image file life cycle; benefits of imaging; document-driven workflow; and planning for workplace changes like postsorting, creating a scanning room, redeveloping job tasks and…

Major histocompatibility complex (MHC) class III genetics in two Amerindian tribes from southern Brazil: the Kaingang and the Guarani.

Science.gov (United States)

Weg-Remers, S; Brenden, M; Schwarz, E; Witzel, K; Schneider, P M; Guerra, L K; Rehfeldt, I R; Lima, M T; Hartmann, D; Petzl-Erler, M L; de Messias, I J; Mauff, G

1997-10-01

Population genetic studies of the major histocompatibility complex (MHC) class III region, comprising C2, BF and C4 phenotypes, and molecular genetic data are rarely available for populations other than Caucasoids. We have investigated three Amerindian populations from Southern Brazil: 131 Kaingang from Ivaí (KIV), 111 Kaingang (KRC) and 100 Guarani (GRC) from Rio das Cobras. Extended MHC haplotypes were derived after standard C2, BF, C4 phenotyping and restriction fragment length polymorphism (RFLP) analysis with TaqI, together with HLA data published previously by segregation analysis. C2 and BF frequencies corresponded to other Amerindian populations. C4B*Q0 frequency was high in the GRC (0.429) but low in the Kaingang. Unusual C4 alleles were found, viz. C4A*58, A*55 and C4B*22 (presumably non-Amerindian) and aberrant C4A*3 of Amerindian origin occurring with a frequency of 0.223 in the GRC. C4A*3 bands of homo- and heterozygous individuals carrying this variant were Rodgers 1 positive and Chido 1,3 positive, showed a C4A specific lysis type and a C4A like alpha-chain. Polymerase chain reaction studies and sequencing showed that this is based on a C4A*3 duplication with a regular C4A*3 and a partially converted C4A*0304 carrying the C4B specific epitopes Ch 6 and Ch 1,3. Associations of class III haplotypes with particular RFLP patterns were similar to those reported for Caucasoids. The previously described association between combined C4A and CYP21P deletions and the 6.4 kb TaqI fragment was not seen in these Amerindians. This fragment occurred within a regular two locus gene structure in the Kaingang, representing a "short" gene at C4 locus I. C4 and CYP21 duplications were frequently observed. The distribution of extended MHC haplotypes provides evidence for a close relationship between the KIV and KRC and a larger genetic distance between the two Kaingang groups and the GRC.

Edge-based correlation image registration for multispectral imaging

Science.gov (United States)

Nandy, Prabal [Albuquerque, NM

2009-11-17

Registration information for images of a common target obtained from a plurality of different spectral bands can be obtained by combining edge detection and phase correlation. The images are edge-filtered, and pairs of the edge-filtered images are then phase correlated to produce phase correlation images. The registration information can be determined based on these phase correlation images.

ImageSURF MOAB2 Image Example

OpenAIRE

O'Mara, Aidan R; Collins, Jessica M; King, Anna E; Vickers, James C; Kirkcaldie, Matthew T K

2017-01-01

A set of 2000x2000 confocal fluorescence images of MOAB2-labelled cortex from APPswe/PS1dE9 mouse models of Alzheimer's disease, sparsely annotated pixel labels and reference segmentation examples. Pixels are annotated as signal (red 0xFFFF0000) and background (blue 0xFF0000FF). Images were captured as stitched 12-bit greyscale single-plane images and cropped to size. Image acquisition was performed at 561nm excitation and 615nm emission wavelengths using a Perkin Elmer Ultraview VOX ima...

Can conditional cash transfer programs generate equality of opportunity in highly unequal societies? Evidence from Brazil

Directory of Open Access Journals (Sweden)

Simone Bohn

2014-09-01

Full Text Available This article examines whether the state, through conditional cash transfer programs (CCT, can reduce the poverty and extremely poverty in societies marred by high levels of income concentration. We focus on one of the most unequal countries in the globe, Brazil, and analyze the extent to which this country's CCT program - Bolsa Família (BF, Family Grant program - is able to improve the life chances of extremely poor beneficiaries, through the three major goals of PBF: First, to immediately end hunger; second, to create basic social rights related to healthcare and education; finally, considering also complementary policies, to integrate adults into the job market. The analysis relies on a quantitative survey with 4,000 beneficiaries and a qualitative survey comprised of in-depth interviews with 38 program's participants from all the regions of the country in 2008, it means that this study is about the five first years of the PBF. In order to answer the research questions, we ran four probit analyses related: a the determinants of the realization of prenatal care; b the determinants of food security among BF beneficiaries, c the determinants that adult BF recipients will return to school, d the determinants that a BF beneficiary will obtain a job. Important results from the study are: First, those who before their participation on PBF were at the margins have now been able to access healthcare services on a more regular basis. Thus, the women at the margins who were systematically excluded - black women, poorly educated and from the North - now, after their participation in the CCT program, have more access to prenatal care and can now count with more availability of public healthcare network. Second, before entering the Bolsa Família program, 50.3% of the participants faced severe food insecurity. This number went down to 36.8% in very five years. Men are more likely than women; non-blacks more likely than blacks; and South and Centre

Transformation invariant image indexing and retrieval for image databases

NARCIS (Netherlands)

Gevers, Th.; Smeulders, A.W.M.

1994-01-01

This paper presents a novel design of an image database system which supports storage, indexing and retrieval of images by content. The image retrieval methodology is based on the observation that images can be discriminated by the presence of image objects and their spatial relations. Images in the

Image processing of integrated video image obtained with a charged-particle imaging video monitor system

International Nuclear Information System (INIS)

Iida, Takao; Nakajima, Takehiro

1988-01-01

A new type of charged-particle imaging video monitor system was constructed for video imaging of the distributions of alpha-emitting and low-energy beta-emitting nuclides. The system can display not only the scintillation image due to radiation on the video monitor but also the integrated video image becoming gradually clearer on another video monitor. The distortion of the image is about 5% and the spatial resolution is about 2 line pairs (lp)mm -1 . The integrated image is transferred to a personal computer and image processing is performed qualitatively and quantitatively. (author)

Charging Effects on Fluid Stream Droplets for Momentum Exchange Between Spacecraft

Science.gov (United States)

2009-01-01

temperature where liquid polymers transition to a brittle glass like state and solid polymers transition to a rubbery state. A technical... Glen Research Center, Thermo Mechanical Systems Branch http://www.grc.nasa.gov/WWW/tmsb/concentrators.html [accessed Sep 29, 2006]. Purcell, E

Hyperspectral small animal fluorescence imaging: spectral selection imaging

Science.gov (United States)

Leavesley, Silas; Jiang, Yanan; Patsekin, Valery; Hall, Heidi; Vizard, Douglas; Robinson, J. Paul

2008-02-01

Molecular imaging is a rapidly growing area of research, fueled by needs in pharmaceutical drug-development for methods for high-throughput screening, pre-clinical and clinical screening for visualizing tumor growth and drug targeting, and a growing number of applications in the molecular biology fields. Small animal fluorescence imaging employs fluorescent probes to target molecular events in vivo, with a large number of molecular targeting probes readily available. The ease at which new targeting compounds can be developed, the short acquisition times, and the low cost (compared to microCT, MRI, or PET) makes fluorescence imaging attractive. However, small animal fluorescence imaging suffers from high optical scattering, absorption, and autofluorescence. Much of these problems can be overcome through multispectral imaging techniques, which collect images at different fluorescence emission wavelengths, followed by analysis, classification, and spectral deconvolution methods to isolate signals from fluorescence emission. We present an alternative to the current method, using hyperspectral excitation scanning (spectral selection imaging), a technique that allows excitation at any wavelength in the visible and near-infrared wavelength range. In many cases, excitation imaging may be more effective at identifying specific fluorescence signals because of the higher complexity of the fluorophore excitation spectrum. Because the excitation is filtered and not the emission, the resolution limit and image shift imposed by acousto-optic tunable filters have no effect on imager performance. We will discuss design of the imager, optimizing the imager for use in small animal fluorescence imaging, and application of spectral analysis and classification methods for identifying specific fluorescence signals.

Preparing diagnostic 3D images for image registration with planning CT images

International Nuclear Information System (INIS)

Tracton, Gregg S.; Miller, Elizabeth P.; Rosenman, Julian; Chang, Sha X.; Sailer, Scott; Boxwala, Azaz; Chaney, Edward L.

1997-01-01

Purpose: Pre-radiotherapy (pre-RT) tomographic images acquired for diagnostic purposes often contain important tumor and/or normal tissue information which is poorly defined or absent in planning CT images. Our two years of clinical experience has shown that computer-assisted 3D registration of pre-RT images with planning CT images often plays an indispensable role in accurate treatment volume definition. Often the only available format of the diagnostic images is film from which the original 3D digital data must be reconstructed. In addition, any digital data, whether reconstructed or not, must be put into a form suitable for incorporation into the treatment planning system. The purpose of this investigation was to identify all problems that must be overcome before this data is suitable for clinical use. Materials and Methods: In the past two years we have 3D-reconstructed 300 diagnostic images from film and digital sources. As a problem was discovered we built a software tool to correct it. In time we collected a large set of such tools and found that they must be applied in a specific order to achieve the correct reconstruction. Finally, a toolkit (ediScan) was built that made all these tools available in the proper manner via a pleasant yet efficient mouse-based user interface. Results: Problems we discovered included different magnifications, shifted display centers, non-parallel image planes, image planes not perpendicular to the long axis of the table-top (shearing), irregularly spaced scans, non contiguous scan volumes, multiple slices per film, different orientations for slice axes (e.g. left-right reversal), slices printed at window settings corresponding to tissues of interest for diagnostic purposes, and printing artifacts. We have learned that the specific steps to correct these problems, in order of application, are: Also, we found that fast feedback and large image capacity (at least 2000 x 2000 12-bit pixels) are essential for practical application

Maxillofacial imaging

Energy Technology Data Exchange (ETDEWEB)

Larheim, T.A. [Oslo Univ. (Norway). Dept. of Maxillofacial Radiology; Westesson, P.L. [Univ. of Rochester School of Medicine and Dentistry, NY (United States). Div. of Diagnostic and Interventional Radiology

2006-07-01

Maxillofacial imaging has evolved dramatically over the past two decades with development of new cross-sectional imaging techniques. Traditional maxillofacial imaging was based on plain films and dental imaging. However, today's advanced imaging techniques with CT and MRI have only been partially implemented for maxillofacial questions. This book bridges the gap between traditional maxillofacial imaging and advanced medical imaging. We have applied CT and MRI to a variety of maxillofacial cases and these are illustrated with high-quality images and multiple planes. A comprehensive chapter on imaging anatomy is also included. This book is useful for oral and maxillofacial radiologists, oral and maxillofacial surgeons, dentists, radiologists, plastic surgeons, head and neck surgeons, and others that work with severe maxillofacial disorders. (orig.)

Space Solar Power Satellite Technology Development at the Glenn Research Center: An Overview

Science.gov (United States)

Dudenhoefer, James E.; George, Patrick J.

2000-01-01

NASA Glenn Research Center (GRC). is participating in the Space Solar Power Exploratory Research and Technology program (SERT) for the development of a solar power satellite concept. The aim of the program is to provide electrical power to Earth by converting the Sun's energy and beaming it to the surface. This paper will give an overall view of the technologies being pursued at GRC including thin film photovoltaics, solar dynamic power systems, space environmental effects, power management and distribution, and electric propulsion. The developmental path not only provides solutions to gigawatt sized space power systems for the future, but provides synergistic opportunities for contemporary space power architectures. More details of Space Solar Power can be found by reading the references sited in this paper and by connecting to the web site http://moonbase.msfc.nasa.gov/ and accessing the "Space Solar Power" section "Public Access" area.

Separation method of heavy-ion particle image from gamma-ray mixed images using an imaging plate

CERN Document Server

Yamadera, A; Ohuchi, H; Nakamura, T; Fukumura, A

1999-01-01

We have developed a separation method of alpha-ray and gamma-ray images using the imaging plate (IP). The IP from which the first image was read out by an image reader was annealed at 50 deg. C for 2 h in a drying oven and the second image was read out by the image reader. It was found out that an annealing ratio, k, which is defined as a ratio of the photo-stimulated luminescence (PSL) density at the first measurement to that at the second measurement, was different for alpha rays and gamma rays. By subtracting the second image multiplied by a factor of k from the first image, the alpha-ray image was separated from the alpha and gamma-ray mixed images. This method was applied to identify the images of helium, carbon and neon particles of high energies using the heavy-ion medical accelerator, HIMAC. (author)

Registration of angiographic image on real-time fluoroscopic image for image-guided percutaneous coronary intervention.

Science.gov (United States)

Kim, Dongkue; Park, Sangsoo; Jeong, Myung Ho; Ryu, Jeha

2018-02-01

In percutaneous coronary intervention (PCI), cardiologists must study two different X-ray image sources: a fluoroscopic image and an angiogram. Manipulating a guidewire while alternately monitoring the two separate images on separate screens requires a deep understanding of the anatomy of coronary vessels and substantial training. We propose 2D/2D spatiotemporal image registration of the two images in a single image in order to provide cardiologists with enhanced visual guidance in PCI. The proposed 2D/2D spatiotemporal registration method uses a cross-correlation of two ECG series in each image to temporally synchronize two separate images and register an angiographic image onto the fluoroscopic image. A guidewire centerline is then extracted from the fluoroscopic image in real time, and the alignment of the centerline with vessel outlines of the chosen angiographic image is optimized using the iterative closest point algorithm for spatial registration. A proof-of-concept evaluation with a phantom coronary vessel model with engineering students showed an error reduction rate greater than 74% on wrong insertion to nontarget branches compared to the non-registration method and more than 47% reduction in the task completion time in performing guidewire manipulation for very difficult tasks. Evaluation with a small number of experienced doctors shows a potentially significant reduction in both task completion time and error rate for difficult tasks. The total registration time with real procedure X-ray (angiographic and fluoroscopic) images takes [Formula: see text] 60 ms, which is within the fluoroscopic image acquisition rate of 15 Hz. By providing cardiologists with better visual guidance in PCI, the proposed spatiotemporal image registration method is shown to be useful in advancing the guidewire to the coronary vessel branches, especially those difficult to insert into.

Multispectral image enhancement processing for microsat-borne imager

Science.gov (United States)

Sun, Jianying; Tan, Zheng; Lv, Qunbo; Pei, Linlin

2017-10-01

With the rapid development of remote sensing imaging technology, the micro satellite, one kind of tiny spacecraft, appears during the past few years. A good many studies contribute to dwarfing satellites for imaging purpose. Generally speaking, micro satellites weigh less than 100 kilograms, even less than 50 kilograms, which are slightly larger or smaller than the common miniature refrigerators. However, the optical system design is hard to be perfect due to the satellite room and weight limitation. In most cases, the unprocessed data captured by the imager on the microsatellite cannot meet the application need. Spatial resolution is the key problem. As for remote sensing applications, the higher spatial resolution of images we gain, the wider fields we can apply them. Consequently, how to utilize super resolution (SR) and image fusion to enhance the quality of imagery deserves studying. Our team, the Key Laboratory of Computational Optical Imaging Technology, Academy Opto-Electronics, is devoted to designing high-performance microsat-borne imagers and high-efficiency image processing algorithms. This paper addresses a multispectral image enhancement framework for space-borne imagery, jointing the pan-sharpening and super resolution techniques to deal with the spatial resolution shortcoming of microsatellites. We test the remote sensing images acquired by CX6-02 satellite and give the SR performance. The experiments illustrate the proposed approach provides high-quality images.

Enhancement of image contrast in linacgram through image processing

International Nuclear Information System (INIS)

Suh, Hyun Suk; Shin, Hyun Kyo; Lee, Re Na

2000-01-01

Conventional radiation therapy portal images gives low contrast images. The purpose of this study was to enhance image contrast of a linacgram by developing a low--cost image processing method. Chest linacgram was obtained by irradiating humanoid phantom and scanned using Diagnostic-Pro scanner for image processing. Several types of scan method were used in scanning. These include optical density scan, histogram equalized scan, linear histogram based scan, linear histogram independent scan, linear optical density scan, logarithmic scan, and power square root scan. The histogram distribution of the scanned images were plotted and the ranges of the gray scale were compared among various scan types. The scanned images were then transformed to the gray window by pallette fitting method and the contrast of the reprocessed portal images were evaluated for image improvement. Portal images of patients were also taken at various anatomic sites and the images were processed by Gray Scale Expansion (GSE) method. The patient images were analyzed to examine the feasibility of using the GSE technique in clinic. The histogram distribution showed that minimum and maximum gray scale ranges of 3192 and 21940 were obtained when the image was scanned using logarithmic method and square root method, respectively. Out of 256 gray scale, only 7 to 30% of the steps were used. After expanding the gray scale to full range, contrast of the portal images were improved. Experiment performed with patient image showed that improved identification of organs were achieved by GSE in portal images of knee joint, head and neck, lung, and pelvis. Phantom study demonstrated that the GSE technique improved image contrast of a linacgram. This indicates that the decrease in image quality resulting from the dual exposure, could be improved by expanding the gray scale. As a result, the improved technique will make it possible to compare the digitally reconstructed radiographs (DRR) and simulation image for

Mirror-Image Equivalence and Interhemispheric Mirror-Image Reversal.

Science.gov (United States)

Corballis, Michael C

2018-01-01

Mirror-image confusions are common, especially in children and in some cases of neurological impairment. They can be a special impediment in activities such as reading and writing directional scripts, where mirror-image patterns (such as b and d ) must be distinguished. Treating mirror images as equivalent, though, can also be adaptive in the natural world, which carries no systematic left-right bias and where the same object or event can appear in opposite viewpoints. Mirror-image equivalence and confusion are natural consequences of a bilaterally symmetrical brain. In the course of learning, mirror-image equivalence may be established through a process of symmetrization, achieved through homotopic interhemispheric exchange in the formation of memory circuits. Such circuits would not distinguish between mirror images. Learning to discriminate mirror-image discriminations may depend either on existing brain asymmetries, or on extensive learning overriding the symmetrization process. The balance between mirror-image equivalence and mirror-image discrimination may nevertheless be precarious, with spontaneous confusions or reversals, such as mirror writing, sometimes appearing naturally or as a manifestation of conditions like dyslexia.

Mirror-Image Equivalence and Interhemispheric Mirror-Image Reversal

Directory of Open Access Journals (Sweden)

Michael C. Corballis

2018-04-01

Full Text Available Mirror-image confusions are common, especially in children and in some cases of neurological impairment. They can be a special impediment in activities such as reading and writing directional scripts, where mirror-image patterns (such as b and d must be distinguished. Treating mirror images as equivalent, though, can also be adaptive in the natural world, which carries no systematic left-right bias and where the same object or event can appear in opposite viewpoints. Mirror-image equivalence and confusion are natural consequences of a bilaterally symmetrical brain. In the course of learning, mirror-image equivalence may be established through a process of symmetrization, achieved through homotopic interhemispheric exchange in the formation of memory circuits. Such circuits would not distinguish between mirror images. Learning to discriminate mirror-image discriminations may depend either on existing brain asymmetries, or on extensive learning overriding the symmetrization process. The balance between mirror-image equivalence and mirror-image discrimination may nevertheless be precarious, with spontaneous confusions or reversals, such as mirror writing, sometimes appearing naturally or as a manifestation of conditions like dyslexia.

Experimental Characterization of a Grid-Loss Event on a 2.5-MW Dynamometer Using Advanced Operational Modal Analysis: Preprint

Energy Technology Data Exchange (ETDEWEB)

Helsen, J.; Weijtjens, W.; Guo, Y.; Keller, J.; McNiff, B.; Devriendt, C.; Guillaume, P.

2015-02-01

This paper experimentally investigates a worst case grid loss event conducted on the National Renewable Energy Laboratory (NREL) Gearbox Reliability Collaborative (GRC) drivetrain mounted on the 2.5MW NREL dynamic nacelle test-rig. The GRC drivetrain has a directly grid-coupled, fixed speed asynchronous generator. The main goal is the assessment of the dynamic content driving this particular assess the dynamic content of the high-speed stage of the GRC gearbox. In addition to external accelerometers, high frequency sampled measurements of strain gauges were used to assess torque fluctuations and bending moments both at the nacelle main shaft and gearbox high-speed shaft (HSS) through the entire duration of the event. Modal analysis was conducted using a polyreference Least Squares Complex Frequency-domain (pLSCF) modal identification estimator. The event driving the torsional resonance was identified. Moreover, the pLSCF estimator identified main drivetrain resonances based on a combination of acceleration and strain measurements. Without external action during the grid-loss event, a mode shape characterized by counter phase rotation of the rotor and generator rotor determined by the drivetrain flexibility and rotor inertias was the main driver of the event. This behavior resulted in significant torque oscillations with large amplitude negative torque periods. Based on tooth strain measurements of the HSS pinion, this work showed that at each zero-crossing, the teeth lost contact and came into contact with the backside flank. In addition, dynamic nontorque loads between the gearbox and generator at the HSS played an important role, as indicated by strain gauge-measurements.

Research and Technology 1999

Science.gov (United States)

2000-01-01

This report selectively summarizes the NASA Glenn Research Center's research and technology accomplishments for the fiscal year 1999. It comprises 130 short articles submitted by the staff scientists and engineers. The report is organized into four major sections: Aeronautics. Research and Technology, Space, and Engineering and Technical Services. A table of contents and an author index have been developed to assist readers in finding articles of special interest. This report is not intended to be a comprehensive summary of all the research and technology work done over the past fiscal year. Most of the work is reported in Glenn-published technical reports, journal articles, and presentations prepared by Glenn staff and contractors. In addition, university grants have enabled faculty members and graduate students to engage in sponsored research that is reported at technical meetings or in journal articles. For each article in this report, a Glenn contact person has been identified, and where possible, reference documents are listed so that additional information can be easily obtained. The diversity of topics attests to the breadth of research and technology being pursued and to the skill mix of the staff that makes it possible. For more information about research at NASA Glenn, visit us on the World Wide Web (http://www.grc.nasa.gov). This document is available on the World Wide Web (http://www.grc.nasa.gov/WWW/RT/). For publicly available reports, visit the Glenn Technical Report Server (GLTRS) on the World Wide Web (http://gltrs.grc.nasa.gov/GLTRS/).

Advanced Stirling Convertor (ASC) Development for NASA RPS

Science.gov (United States)

Wong, Wayne A.; Wilson, Scott; Collins, Josh

2014-01-01

Sunpower's Advanced Stirling Convertor (ASC) initiated development under contract to the NASA Glenn Research Center (GRC) and after a series of successful demonstrations, the ASC began transitioning from a technology development project to flight development project. The ASC has very high power conversion efficiency making it attractive for future Radioisotope Power Systems (RPS) in order to make best use of the low plutonium-238 fuel inventory in the U.S. In recent years, the ASC became part of the NASA-Department of Energy Advanced Stirling Radioisotope Generator (ASRG) Integrated Project. Sunpower held two parallel contracts to produce ASC convertors, one with the Department of Energy/Lockheed Martin to produce the ASC-F flight convertors, and one with NASA GRC for the production of ASC-E3 engineering units, the initial units of which served as production pathfinders. The integrated ASC technical team successfully overcame various technical challenges that led to the completion and delivery of the first two pairs of flight-like ASC-E3 by 2013. However, in late Fall 2013, the DOE initiated termination of the Lockheed Martin ASRG flight development contract driven primarily by budget constraints. NASA continues to recognize the importance of high efficiency ASC power conversion for RPS and continues investment in the technology including the continuation of ASC-E3 production at Sunpower and the assembly of the ASRG Engineering Unit #2. This paper provides a summary of ASC technical accomplishments, overview of tests at GRC, plans for continued ASC production at Sunpower, and status of Stirling technology development.

Continuous imaging space in three-dimensional integral imaging

International Nuclear Information System (INIS)

Zhang Lei; Yang Yong; Wang Jin-Gang; Zhao Xing; Fang Zhi-Liang; Yuan Xiao-Cong

2013-01-01

We report an integral imaging method with continuous imaging space. This method simultaneously reconstructs real and virtual images in the virtual mode, with a minimum gap that separates the entire imaging space into real and virtual space. Experimental results show that the gap is reduced to 45% of that in a conventional integral imaging system with the same parameters. (electromagnetism, optics, acoustics, heat transfer, classical mechanics, and fluid dynamics)

Image reconstruction of dynamic infrared single-pixel imaging system

Science.gov (United States)

Tong, Qi; Jiang, Yilin; Wang, Haiyan; Guo, Limin

2018-03-01

Single-pixel imaging technique has recently received much attention. Most of the current single-pixel imaging is aimed at relatively static targets or the imaging system is fixed, which is limited by the number of measurements received through the single detector. In this paper, we proposed a novel dynamic compressive imaging method to solve the imaging problem, where exists imaging system motion behavior, for the infrared (IR) rosette scanning system. The relationship between adjacent target images and scene is analyzed under different system movement scenarios. These relationships are used to build dynamic compressive imaging models. Simulation results demonstrate that the proposed method can improve the reconstruction quality of IR image and enhance the contrast between the target and the background in the presence of system movement.

Stereoscopic Integrated Imaging Goggles for Multimodal Intraoperative Image Guidance.

Directory of Open Access Journals (Sweden)

Christopher A Mela

Full Text Available We have developed novel stereoscopic wearable multimodal intraoperative imaging and display systems entitled Integrated Imaging Goggles for guiding surgeries. The prototype systems offer real time stereoscopic fluorescence imaging and color reflectance imaging capacity, along with in vivo handheld microscopy and ultrasound imaging. With the Integrated Imaging Goggle, both wide-field fluorescence imaging and in vivo microscopy are provided. The real time ultrasound images can also be presented in the goggle display. Furthermore, real time goggle-to-goggle stereoscopic video sharing is demonstrated, which can greatly facilitate telemedicine. In this paper, the prototype systems are described, characterized and tested in surgeries in biological tissues ex vivo. We have found that the system can detect fluorescent targets with as low as 60 nM indocyanine green and can resolve structures down to 0.25 mm with large FOV stereoscopic imaging. The system has successfully guided simulated cancer surgeries in chicken. The Integrated Imaging Goggle is novel in 4 aspects: it is (a the first wearable stereoscopic wide-field intraoperative fluorescence imaging and display system, (b the first wearable system offering both large FOV and microscopic imaging simultaneously,

Imaging systems in nuclear medicine and image evaluation

International Nuclear Information System (INIS)

Beck, R.; Charleston, D.; Metz, C.

1980-01-01

This project deals with imaging systems in nuclear medicine and image evaluation and is presented as four subprojects. The goal of the first subproject is to improve diagnositc image quality by development of a general computer code for optimizing collimator design. The second subproject deals with a secondary emission and fluorescence technique for thyroid scanning while the third subproject emphasizes the need for more sophisticated image processing systems such as coherent optical spatial filtering systems and digital image processing. The fourth subproject presents a new approach for processing image data by taking into account the energy of each detected gamma-ray photon

Imaging sciences workshop

Energy Technology Data Exchange (ETDEWEB)

Candy, J.V.

1994-11-15

This workshop on the Imaging Sciences sponsored by Lawrence Livermore National Laboratory contains short abstracts/articles submitted by speakers. The topic areas covered include the following: Astronomical Imaging; biomedical imaging; vision/image display; imaging hardware; imaging software; Acoustic/oceanic imaging; microwave/acoustic imaging; computed tomography; physical imaging; imaging algorithms. Selected papers are indexed separately for inclusion in the Energy Science and Technology Database.

PC image processing

International Nuclear Information System (INIS)

Hwa, Mok Jin Il; Am, Ha Jeng Ung

1995-04-01

This book starts summary of digital image processing and personal computer, and classification of personal computer image processing system, digital image processing, development of personal computer and image processing, image processing system, basic method of image processing such as color image processing and video processing, software and interface, computer graphics, video image and video processing application cases on image processing like satellite image processing, color transformation of image processing in high speed and portrait work system.

Lossy image compression for digital medical imaging systems

Science.gov (United States)

Wilhelm, Paul S.; Haynor, David R.; Kim, Yongmin; Nelson, Alan C.; Riskin, Eve A.

1990-07-01

Image compression at rates of 10:1 or greater could make PACS much more responsive and economically attractive. This paper describes a protocol for subjective and objective evaluation of the fidelity of compressed/decompressed images to the originals and presents the results ofits application to four representative and promising compression methods. The methods examined are predictive pruned tree-structured vector quantization, fractal compression, the discrete cosine transform with equal weighting of block bit allocation, and the discrete cosine transform with human visual system weighting of block bit allocation. Vector quantization is theoretically capable of producing the best compressed images, but has proven to be difficult to effectively implement. It has the advantage that it can reconstruct images quickly through a simple lookup table. Disadvantages are that codebook training is required, the method is computationally intensive, and achieving the optimum performance would require prohibitively long vector dimensions. Fractal compression is a relatively new compression technique, but has produced satisfactory results while being computationally simple. It is fast at both image compression and image reconstruction. Discrete cosine iransform techniques reproduce images well, but have traditionally been hampered by the need for intensive computing to compress and decompress images. A protocol was developed for side-by-side observer comparison of reconstructed images with originals. Three 1024 X 1024 CR (Computed Radiography) images and two 512 X 512 X-ray CT images were viewed at six bit rates (0.2, 0.4, 0.6, 0.9, 1.2, and 1.5 bpp for CR, and 1.0, 1.3, 1.6, 1.9, 2.2, 2.5 bpp for X-ray CT) by nine radiologists at the University of Washington Medical Center. The CR images were viewed on a Pixar II Megascan (2560 X 2048) monitor and the CT images on a Sony (1280 X 1024) monitor. The radiologists' subjective evaluations of image fidelity were compared to

78 FR 52215 - Notice of Information Collection

Science.gov (United States)

2013-08-22

.... Method of Collection Electronic and Paper III. Data Title: NASA GRC Shadowing and Exploring OMB Number: 2700-XXXX Type of review: Existing Collection without OMB Approval Affected Public: Individuals... in the 14-20 age groups. It connects classroom training to tangible activities that enable practical...

Defense AT and L. Volume 38, Number 1, January-February 2009

Science.gov (United States)

2009-01-01

magazine. The Star Trek theme was an entertaining way to eff ectively present important information. I liked the rules the author cited, especially...technology.grc.nasa.gov/ Promotes competitiveness of U.S. in- dustry through commercial use of NASA technologies and expertise. National Contract

Image Analysis for X-ray Imaging of Food

DEFF Research Database (Denmark)

Einarsdottir, Hildur

for quality and safety evaluation of food products. In this effort the fields of statistics, image analysis and statistical learning are combined, to provide analytical tools for determining the aforementioned food traits. The work demonstrated includes a quantitative analysis of heat induced changes......X-ray imaging systems are increasingly used for quality and safety evaluation both within food science and production. They offer non-invasive and nondestructive penetration capabilities to image the inside of food. This thesis presents applications of a novel grating-based X-ray imaging technique...... and defect detection in food. Compared to the complex three dimensional analysis of microstructure, here two dimensional images are considered, making the method applicable for an industrial setting. The advantages obtained by grating-based imaging are compared to conventional X-ray imaging, for both foreign...

The supposedly attenuated Hy-HK variant of highly virulent Hypr strain of Tick-borne encephalitis virus is obviously a strain of Langat virus

Czech Academy of Sciences Publication Activity Database

Růžek, Daniel; Štěrba, Ján; Kopecký, Jan; Grubhoffer, Libor

2006-01-01

Roč. 50, č. 4 (2006), s. 277-278 ISSN 0001-723X R&D Projects: GA ČR(CZ) GA524/06/1479 Grant - others:Grant Agency of the University of South Bohemia(CZ) 35/2005/P-BF Institutional research plan: CEZ:AV0Z60220518 Keywords : TBE virus * Langat virus * Hy-HK attenuated variant Subject RIV: GJ - Animal Vermins ; Diseases, Veterinary Medicine Impact factor: 0.788, year: 2006

Image Processing and Features Extraction of Fingerprint Images ...

African Journals Online (AJOL)

To demonstrate the importance of the image processing of fingerprint images prior to image enrolment or comparison, the set of fingerprint images in databases (a) and (b) of the FVC (Fingerprint Verification Competition) 2000 database were analyzed using a features extraction algorithm. This paper presents the results of ...

Image quality at synthetic brain magnetic resonance imaging in children

Energy Technology Data Exchange (ETDEWEB)

Lee, So Mi; Cho, Seung Hyun; Kim, Won Hwa; Kim, Hye Jung [Kyungpook National University Hospital, Department of Radiology, Daegu (Korea, Republic of); Choi, Young Hun; Cheon, Jung-Eun; Kim, In-One [Seoul National University College of Medicine, Department of Radiology and Institute of Radiation Medicine, Seoul (Korea, Republic of); Cho, Hyun-Hae [Ewha Womans University Mokdong Hospital, Department of Radiology, Seoul (Korea, Republic of); You, Sun-Kyoung [Chungnam National University Hospital, Department of Radiology, Daejeon (Korea, Republic of); Park, Sook-Hyun [Kyungpook National University Hospital, Department of Pediatrics, Daegu (Korea, Republic of); Hwang, Moon Jung [GE Healthcare, MR Applications and Workflow, Seoul (Korea, Republic of)

2017-11-15

The clinical application of the multi-echo, multi-delay technique of synthetic magnetic resonance imaging (MRI) generates multiple sequences in a single acquisition but has mainly been used in adults. To evaluate the image quality of synthetic brain MR in children compared with that of conventional images. Twenty-nine children (median age: 6 years, range: 0-16 years) underwent synthetic and conventional imaging. Synthetic (T2-weighted, T1-weighted and fluid-attenuated inversion recovery [FLAIR]) images with settings matching those of the conventional images were generated. The overall image quality, gray/white matter differentiation, lesion conspicuity and image degradations were rated on a 5-point scale. The relative contrasts were assessed quantitatively and acquisition times for the two imaging techniques were compared. Synthetic images were inferior due to more pronounced image degradations; however, there were no significant differences for T1- and T2-weighted images in children <2 years old. The quality of T1- and T2-weighted images were within the diagnostically acceptable range. FLAIR images showed greatly reduced quality. Gray/white matter differentiation was comparable or better in synthetic T1- and T2-weighted images, but poorer in FLAIR images. There was no effect on lesion conspicuity. Synthetic images had equal or greater relative contrast. Acquisition time was approximately two-thirds of that for conventional sequences. Synthetic T1- and T2-weighted images were diagnostically acceptable, but synthetic FLAIR images were not. Lesion conspicuity and gray/white matter differentiation were comparable to conventional MRI. (orig.)

Luminescence imaging using radionuclides: a potential application in molecular imaging

International Nuclear Information System (INIS)

Park, Jeong Chan; Il An, Gwang; Park, Se-Il; Oh, Jungmin; Kim, Hong Joo; Su Ha, Yeong; Wang, Eun Kyung; Min Kim, Kyeong; Kim, Jung Young; Lee, Jaetae; Welch, Michael J.; Yoo, Jeongsoo

2011-01-01

Introduction: Nuclear and optical imaging are complementary in many aspects and there would be many advantages when optical imaging probes are prepared using radionuclides rather than classic fluorophores, and when nuclear and optical dual images are obtained using single imaging probe. Methods: The luminescence intensities of various radionuclides having different decay modes have been assayed using luminescence imaging and in vitro luminometer. Radioiodinated Herceptin was injected into a tumor-bearing mouse, and luminescence and microPET images were obtained. The plant dipped in [ 32 P]phosphate solution was scanned in luminescence mode. Radio-TLC plate was also imaged in the same imaging mode. Results: Radionuclides emitting high energy β + /β - particles showed higher luminescence signals. NIH3T6.7 tumors were detected in both optical and nuclear imaging. The uptake of [ 32 P]phosphate in plant was easily followed by luminescence imaging. Radio-TLC plate was visualized and radiochemical purity was quantified using luminescence imaging. Conclusion: Many radionuclides with high energetic β + or β - particles during decay were found to be imaged in luminescence mode due mainly to Cerenkov radiation. 'Cerenkov imaging' provides a new optical imaging platform and an invaluable bridge between optical and nuclear imaging. New optical imaging probes could be easily prepared using well-established radioiodination methods. Cerenkov imaging will have more applications in the research field of plant science and autoradiography.

Color image guided depth image super resolution using fusion filter

Science.gov (United States)

He, Jin; Liang, Bin; He, Ying; Yang, Jun

2018-04-01

Depth cameras are currently playing an important role in many areas. However, most of them can only obtain lowresolution (LR) depth images. Color cameras can easily provide high-resolution (HR) color images. Using color image as a guide image is an efficient way to get a HR depth image. In this paper, we propose a depth image super resolution (SR) algorithm, which uses a HR color image as a guide image and a LR depth image as input. We use the fusion filter of guided filter and edge based joint bilateral filter to get HR depth image. Our experimental results on Middlebury 2005 datasets show that our method can provide better quality in HR depth images both numerically and visually.

Epidural fat image in lumbar magnetic resonance image

International Nuclear Information System (INIS)

Nishijima, Yuichiro; Yamasaki, Yasuo; Higashida, Norihiko; Okada, Masato

1993-01-01

To examine epidural fat images, lumbar magnetic resonance (MR) images were retrospectively reviewed in a total of 103 patients with surgically proven lumbar disc herniation (DH, n=57) and lumbar canal stenosis (LCS, n=46). Epidural fat images consisted of middorsal epidural fat (MDF), paramedian ventral fat (PVF) and intervertebral foraminal fat (IFF) ones. In the group of DH, the thickness of MDF image did not correlate with that of subcutaneous fat, suggesting that epidural fat was not affected by body fat. From the pathophysiological point of view, decrease and disappearance of MDF images correlated with compression of the epidural canal. Decrease and disappearance of PVF images lead to suspicious compression of the traversing root. In addition, asymmetrical PVF images were useful for the bilateral diagnosis of herniation. Abnormal findings of IFF images were suggestive of compression of the exiting nerve root at the intervertebral foramen. This was also seen frequently at the non-responsible level in patients over the age of 50. Degenerative and sequentrated spondylolistheses in the group of LCS were more frequently associated with a higher incidence of abnormal findings of IFF images, suggesting the presence of existing nerve root compression. (N.K.)

Improving image quality in portal venography with spectral CT imaging

International Nuclear Information System (INIS)

Zhao, Li-qin; He, Wen; Li, Jian-ying; Chen, Jiang-hong; Wang, Ke-yang; Tan, Li

2012-01-01

Objective: To investigate the effect of energy spectral CT on the image quality of CT portal venography in cirrhosis patients. Materials and methods: 30 portal hypertension patients underwent spectral CT examination using a single-tube, fast dual tube voltage switching technique. 101 sets of monochromatic images were generated from 40 keV to 140 keV. Image noise and contrast-to-noise ratio (CNR) for portal veins from the monochromatic images were measured. An optimal monochromatic image set was selected for obtaining the best CNR for portal veins. The image noise and CNR of the intra-hepatic portal vein and extra-hepatic main stem at the selected monochromatic level were compared with those from the conventional polychromatic images. Image quality was also assessed and compared. Results: The monochromatic images at 51 keV were found to provide the best CNR for both the intra-hepatic and extra-hepatic portal veins. At this energy level, the monochromatic images had about 100% higher CNR than the polychromatic images with a moderate 30% noise increase. The qualitative image quality assessment was also statistically higher with monochromatic images at 51 keV. Conclusion: Monochromatic images at 51 keV for CT portal venography could improve CNR for displaying hepatic portal veins and improve the overall image quality.

Improving image quality in portal venography with spectral CT imaging

Energy Technology Data Exchange (ETDEWEB)

Zhao, Li-qin, E-mail: zhaolqzr@sohu.com [Department of Radiology, Beijing Friendship Hospital Affiliated to Capital Medical University, Beijing,100050 (China); He, Wen, E-mail: hewen1724@sina.com [Department of Radiology, Beijing Friendship Hospital Affiliated to Capital Medical University, Beijing,100050 (China); Li, Jian-ying, E-mail: jianying.li@med.ge.com [CT Advanced Application and Research, GE Healthcare, 100176 China (China); Chen, Jiang-hong, E-mail: chenjianghong1973@hotmail.com [Department of Radiology, Beijing Friendship Hospital Affiliated to Capital Medical University, Beijing,100050 (China); Wang, Ke-yang, E-mail: ke7ke@sina.com [Department of Radiology, Beijing Friendship Hospital Affiliated to Capital Medical University, Beijing,100050 (China); Tan, Li, E-mail: Litan@ge.com [CT product, GE Healthcare, 100176 China (China)

2012-08-15

Objective: To investigate the effect of energy spectral CT on the image quality of CT portal venography in cirrhosis patients. Materials and methods: 30 portal hypertension patients underwent spectral CT examination using a single-tube, fast dual tube voltage switching technique. 101 sets of monochromatic images were generated from 40 keV to 140 keV. Image noise and contrast-to-noise ratio (CNR) for portal veins from the monochromatic images were measured. An optimal monochromatic image set was selected for obtaining the best CNR for portal veins. The image noise and CNR of the intra-hepatic portal vein and extra-hepatic main stem at the selected monochromatic level were compared with those from the conventional polychromatic images. Image quality was also assessed and compared. Results: The monochromatic images at 51 keV were found to provide the best CNR for both the intra-hepatic and extra-hepatic portal veins. At this energy level, the monochromatic images had about 100% higher CNR than the polychromatic images with a moderate 30% noise increase. The qualitative image quality assessment was also statistically higher with monochromatic images at 51 keV. Conclusion: Monochromatic images at 51 keV for CT portal venography could improve CNR for displaying hepatic portal veins and improve the overall image quality.

Image fusion between whole body FDG PET images and whole body MRI images using a full-automatic mutual information-based multimodality image registration software

International Nuclear Information System (INIS)

Uchida, Yoshitaka; Nakano, Yoshitada; Fujibuchi, Toshiou; Isobe, Tomoko; Kazama, Toshiki; Ito, Hisao

2006-01-01

We attempted image fusion between whole body PET and whole body MRI of thirty patients using a full-automatic mutual information (MI) -based multimodality image registration software and evaluated accuracy of this method and impact of the coregistrated imaging on diagnostic accuracy. For 25 of 30 fused images in body area, translating gaps were within 6 mm in all axes and rotating gaps were within 2 degrees around all axes. In head and neck area, considerably much gaps caused by difference of head inclination at imaging occurred in 16 patients, however these gaps were able to decrease by fused separately. In 6 patients, diagnostic accuracy using PET/MRI fused images was superior compared by PET image alone. This work shows that whole body FDG PET images and whole body MRI images can be automatically fused using MI-based multimodality image registration software accurately and this technique can add useful information when evaluating FDG PET images. (author)

Fluorescence Image Segmentation by using Digitally Reconstructed Fluorescence Images

OpenAIRE

Blumer, Clemens; Vivien, Cyprien; Oertner, Thomas G; Vetter, Thomas

2011-01-01

In biological experiments fluorescence imaging is used to image living and stimulated neurons. But the analysis of fluorescence images is a difficult task. It is not possible to conclude the shape of an object from fluorescence images alone. Therefore, it is not feasible to get good manual segmented nor ground truth data from fluorescence images. Supervised learning approaches are not possible without training data. To overcome this issues we propose to synthesize fluorescence images and call...

Medical Image Tamper Detection Based on Passive Image Authentication.

Science.gov (United States)

Ulutas, Guzin; Ustubioglu, Arda; Ustubioglu, Beste; V Nabiyev, Vasif; Ulutas, Mustafa

2017-12-01

Telemedicine has gained popularity in recent years. Medical images can be transferred over the Internet to enable the telediagnosis between medical staffs and to make the patient's history accessible to medical staff from anywhere. Therefore, integrity protection of the medical image is a serious concern due to the broadcast nature of the Internet. Some watermarking techniques are proposed to control the integrity of medical images. However, they require embedding of extra information (watermark) into image before transmission. It decreases visual quality of the medical image and can cause false diagnosis. The proposed method uses passive image authentication mechanism to detect the tampered regions on medical images. Structural texture information is obtained from the medical image by using local binary pattern rotation invariant (LBPROT) to make the keypoint extraction techniques more successful. Keypoints on the texture image are obtained with scale invariant feature transform (SIFT). Tampered regions are detected by the method by matching the keypoints. The method improves the keypoint-based passive image authentication mechanism (they do not detect tampering when the smooth region is used for covering an object) by using LBPROT before keypoint extraction because smooth regions also have texture information. Experimental results show that the method detects tampered regions on the medical images even if the forged image has undergone some attacks (Gaussian blurring/additive white Gaussian noise) or the forged regions are scaled/rotated before pasting.

Image Gallery

Science.gov (United States)

... R S T U V W X Y Z Image Gallery Share: The Image Gallery contains high-quality digital photographs available from ... Select a category below to view additional thumbnail images. Images are available for direct download in 2 ...

Selections from 2017: Image Processing with AstroImageJ

Science.gov (United States)

Kohler, Susanna

2017-12-01

Editors note:In these last two weeks of 2017, well be looking at a few selections that we havent yet discussed on AAS Nova from among the most-downloaded paperspublished in AAS journals this year. The usual posting schedule will resume in January.AstroImageJ: Image Processing and Photometric Extraction for Ultra-Precise Astronomical Light CurvesPublished January2017The AIJ image display. A wide range of astronomy specific image display options and image analysis tools are available from the menus, quick access icons, and interactive histogram. [Collins et al. 2017]Main takeaway:AstroImageJ is a new integrated software package presented in a publication led byKaren Collins(Vanderbilt University,Fisk University, andUniversity of Louisville). Itenables new users even at the level of undergraduate student, high school student, or amateur astronomer to quickly start processing, modeling, and plotting astronomical image data.Why its interesting:Science doesnt just happen the momenta telescope captures a picture of a distantobject. Instead, astronomical images must firstbe carefully processed to clean up thedata, and this data must then be systematically analyzed to learn about the objects within it. AstroImageJ as a GUI-driven, easily installed, public-domain tool is a uniquelyaccessible tool for thisprocessing and analysis, allowing even non-specialist users to explore and visualizeastronomical data.Some features ofAstroImageJ:(as reported by Astrobites)Image calibration:generate master flat, dark, and bias framesImage arithmetic:combineimages viasubtraction, addition, division, multiplication, etc.Stack editing:easily perform operations on a series of imagesImage stabilization and image alignment featuresPrecise coordinate converters:calculate Heliocentric and Barycentric Julian DatesWCS coordinates:determine precisely where atelescope was pointed for an image by PlateSolving using Astronomy.netMacro and plugin support:write your own macrosMulti-aperture photometry

Medical imaging technology

CERN Document Server

Haidekker, Mark A

2013-01-01

Biomedical imaging is a relatively young discipline that started with Conrad Wilhelm Roentgen’s discovery of the x-ray in 1885. X-ray imaging was rapidly adopted in hospitals around the world. However, it was the advent of computerized data and image processing that made revolutionary new imaging modalities possible. Today, cross-sections and three-dimensional reconstructions of the organs inside the human body is possible with unprecedented speed, detail and quality. This book provides an introduction into the principles of image formation of key medical imaging modalities: X-ray projection imaging, x-ray computed tomography, magnetic resonance imaging, ultrasound imaging, and radionuclide imaging. Recent developments in optical imaging are also covered. For each imaging modality, the introduction into the physical principles and sources of contrast is provided, followed by the methods of image formation, engineering aspects of the imaging devices, and a discussion of strengths and limitations of the modal...

Annotating images by mining image search results

NARCIS (Netherlands)

Wang, X.J.; Zhang, L.; Li, X.; Ma, W.Y.

2008-01-01

Although it has been studied for years by the computer vision and machine learning communities, image annotation is still far from practical. In this paper, we propose a novel attempt at model-free image annotation, which is a data-driven approach that annotates images by mining their search

Automatic detection of blurred images in UAV image sets

Science.gov (United States)

Sieberth, Till; Wackrow, Rene; Chandler, Jim H.

2016-12-01

Unmanned aerial vehicles (UAV) have become an interesting and active research topic for photogrammetry. Current research is based on images acquired by an UAV, which have a high ground resolution and good spectral and radiometrical resolution, due to the low flight altitudes combined with a high resolution camera. UAV image flights are also cost effective and have become attractive for many applications including, change detection in small scale areas. One of the main problems preventing full automation of data processing of UAV imagery is the degradation effect of blur caused by camera movement during image acquisition. This can be caused by the normal flight movement of the UAV as well as strong winds, turbulence or sudden operator inputs. This blur disturbs the visual analysis and interpretation of the data, causes errors and can degrade the accuracy in automatic photogrammetric processing algorithms. The detection and removal of these images is currently achieved manually, which is both time consuming and prone to error, particularly for large image-sets. To increase the quality of data processing an automated process is necessary, which must be both reliable and quick. This paper describes the development of an automatic filtering process, which is based upon the quantification of blur in an image. Images with known blur are processed digitally to determine a quantifiable measure of image blur. The algorithm is required to process UAV images fast and reliably to relieve the operator from detecting blurred images manually. The newly developed method makes it possible to detect blur caused by linear camera displacement and is based on human detection of blur. Humans detect blurred images best by comparing it to other images in order to establish whether an image is blurred or not. The developed algorithm simulates this procedure by creating an image for comparison using image processing. Creating internally a comparable image makes the method independent of

Image quality (IQ) guided multispectral image compression

Science.gov (United States)

Zheng, Yufeng; Chen, Genshe; Wang, Zhonghai; Blasch, Erik

2016-05-01

Image compression is necessary for data transportation, which saves both transferring time and storage space. In this paper, we focus on our discussion on lossy compression. There are many standard image formats and corresponding compression algorithms, for examples, JPEG (DCT -- discrete cosine transform), JPEG 2000 (DWT -- discrete wavelet transform), BPG (better portable graphics) and TIFF (LZW -- Lempel-Ziv-Welch). The image quality (IQ) of decompressed image will be measured by numerical metrics such as root mean square error (RMSE), peak signal-to-noise ratio (PSNR), and structural Similarity (SSIM) Index. Given an image and a specified IQ, we will investigate how to select a compression method and its parameters to achieve an expected compression. Our scenario consists of 3 steps. The first step is to compress a set of interested images by varying parameters and compute their IQs for each compression method. The second step is to create several regression models per compression method after analyzing the IQ-measurement versus compression-parameter from a number of compressed images. The third step is to compress the given image with the specified IQ using the selected compression method (JPEG, JPEG2000, BPG, or TIFF) according to the regressed models. The IQ may be specified by a compression ratio (e.g., 100), then we will select the compression method of the highest IQ (SSIM, or PSNR). Or the IQ may be specified by a IQ metric (e.g., SSIM = 0.8, or PSNR = 50), then we will select the compression method of the highest compression ratio. Our experiments tested on thermal (long-wave infrared) images (in gray scales) showed very promising results.

Vaccine Images on Twitter: Analysis of What Images are Shared

Science.gov (United States)

Dredze, Mark

2018-01-01

Background Visual imagery plays a key role in health communication; however, there is little understanding of what aspects of vaccine-related images make them effective communication aids. Twitter, a popular venue for discussions related to vaccination, provides numerous images that are shared with tweets. Objective The objectives of this study were to understand how images are used in vaccine-related tweets and provide guidance with respect to the characteristics of vaccine-related images that correlate with the higher likelihood of being retweeted. Methods We collected more than one million vaccine image messages from Twitter and characterized various properties of these images using automated image analytics. We fit a logistic regression model to predict whether or not a vaccine image tweet was retweeted, thus identifying characteristics that correlate with a higher likelihood of being shared. For comparison, we built similar models for the sharing of vaccine news on Facebook and for general image tweets. Results Most vaccine-related images are duplicates (125,916/237,478; 53.02%) or taken from other sources, not necessarily created by the author of the tweet. Almost half of the images contain embedded text, and many include images of people and syringes. The visual content is highly correlated with a tweet’s textual topics. Vaccine image tweets are twice as likely to be shared as nonimage tweets. The sentiment of an image and the objects shown in the image were the predictive factors in determining whether an image was retweeted. Conclusions We are the first to study vaccine images on Twitter. Our findings suggest future directions for the study and use of vaccine imagery and may inform communication strategies around vaccination. Furthermore, our study demonstrates an effective study methodology for image analysis. PMID:29615386

Vaccine Images on Twitter: Analysis of What Images are Shared.

Science.gov (United States)

Chen, Tao; Dredze, Mark

2018-04-03

Visual imagery plays a key role in health communication; however, there is little understanding of what aspects of vaccine-related images make them effective communication aids. Twitter, a popular venue for discussions related to vaccination, provides numerous images that are shared with tweets. The objectives of this study were to understand how images are used in vaccine-related tweets and provide guidance with respect to the characteristics of vaccine-related images that correlate with the higher likelihood of being retweeted. We collected more than one million vaccine image messages from Twitter and characterized various properties of these images using automated image analytics. We fit a logistic regression model to predict whether or not a vaccine image tweet was retweeted, thus identifying characteristics that correlate with a higher likelihood of being shared. For comparison, we built similar models for the sharing of vaccine news on Facebook and for general image tweets. Most vaccine-related images are duplicates (125,916/237,478; 53.02%) or taken from other sources, not necessarily created by the author of the tweet. Almost half of the images contain embedded text, and many include images of people and syringes. The visual content is highly correlated with a tweet's textual topics. Vaccine image tweets are twice as likely to be shared as nonimage tweets. The sentiment of an image and the objects shown in the image were the predictive factors in determining whether an image was retweeted. We are the first to study vaccine images on Twitter. Our findings suggest future directions for the study and use of vaccine imagery and may inform communication strategies around vaccination. Furthermore, our study demonstrates an effective study methodology for image analysis. ©Tao Chen, Mark Dredze. Originally published in the Journal of Medical Internet Research (http://www.jmir.org), 03.04.2018.

212Pb-Labeled Antibody 225.28 Targeted to Chondroitin Sulfate Proteoglycan 4 for Triple-Negative Breast Cancer Therapy in Mouse Models

Directory of Open Access Journals (Sweden)

Benjamin B. Kasten

2018-03-01

Full Text Available Triple-negative breast cancer (TNBC is an aggressive subtype of breast cancer with a poor prognosis. There is a clinical need for effective, targeted therapy strategies that destroy both differentiated TNBC cells and TNBC cancer initiating cells (CICs, as the latter are implicated in the metastasis and recurrence of TNBC. Chondroitin sulfate proteoglycan 4 (CSPG4 is overexpressed on differentiated tumor cells and CICs obtained from TNBC patient specimens, suggesting that CSPG4 may be a clinically relevant target for the imaging and therapy of TNBC. The purpose of this study was to determine whether α-particle radioimmunotherapy (RIT targeting TNBC cells using the CSPG4-specific monoclonal antibody (mAb 225.28 as a carrier was effective at eliminating TNBC tumors in preclinical models. To this end, mAb 225.28 labeled with 212Pb (212Pb-225.28 as a source of α-particles for RIT was used for in vitro Scatchard assays and clonogenic survival assays with human TNBC cells (SUM159 and 2LMP grown as adherent cells or non-adherent CIC-enriched mammospheres. Immune-deficient mice bearing orthotopic SUM159 or 2LMP xenografts were injected i.v. with the targeted (225.28 or irrelevant isotype-matched control (F3-C25 mAbs, labeled with 99mTc, 125I, or 212Pb for in vivo imaging, biodistribution, or tumor growth inhibition studies. 212Pb-225.28 bound to adherent SUM159 and 2LMP cells and to CICs from SUM159 and 2LMP mammospheres with a mean affinity of 0.5 nM. Nearly ten times more binding sites per cell were present on SUM159 cells and CICs compared with 2LMP cells. 212Pb-225.28 was six to seven times more effective than 212Pb-F3-C25 at inhibiting SUM159 cell and CIC clonogenic survival (p < 0.05. Radiolabeled mAb 225.28 showed significantly higher uptake than radiolabeled mAb F3-C25 in SUM159 and 2LMP xenografts (p < 0.05, and the uptake of 212Pb-225.28 in TNBC xenografts was correlated with target epitope expression. 212Pb-225.28 caused dose

Image fusion in x-ray differential phase-contrast imaging

Science.gov (United States)

Haas, W.; Polyanskaya, M.; Bayer, F.; Gödel, K.; Hofmann, H.; Rieger, J.; Ritter, A.; Weber, T.; Wucherer, L.; Durst, J.; Michel, T.; Anton, G.; Hornegger, J.

2012-02-01

Phase-contrast imaging is a novel modality in the field of medical X-ray imaging. The pioneer method is the grating-based interferometry which has no special requirements to the X-ray source and object size. Furthermore, it provides three different types of information of an investigated object simultaneously - absorption, differential phase-contrast and dark-field images. Differential phase-contrast and dark-field images represent a completely new information which has not yet been investigated and studied in context of medical imaging. In order to introduce phase-contrast imaging as a new modality into medical environment the resulting information about the object has to be correctly interpreted. The three output images reflect different properties of the same object the main challenge is to combine and visualize these data in such a way that it diminish the information explosion and reduce the complexity of its interpretation. This paper presents an intuitive image fusion approach which allows to operate with grating-based phase-contrast images. It combines information of the three different images and provides a single image. The approach is implemented in a fusion framework which is aimed to support physicians in study and analysis. The framework provides the user with an intuitive graphical user interface allowing to control the fusion process. The example given in this work shows the functionality of the proposed method and the great potential of phase-contrast imaging in medical practice.

Readout-Segmented Echo-Planar Imaging in Diffusion-Weighted MR Imaging in Breast Cancer: Comparison with Single-Shot Echo-Planar Imaging in Image Quality

International Nuclear Information System (INIS)

Kim, Yun Ju; Kim, Sung Hun; Kang, Bong Joo; Park, Chang Suk; Kim, Hyeon Sook; Son, Yo Han; Porter, David Andrew; Song, Byung Joo

2014-01-01

The purpose of this study was to compare the image quality of standard single-shot echo-planar imaging (ss-EPI) and that of readout-segmented EPI (rs-EPI) in patients with breast cancer. Seventy-one patients with 74 breast cancers underwent both ss-EPI and rs-EPI. For qualitative comparison of image quality, three readers independently assessed the two sets of diffusion-weighted (DW) images. To evaluate geometric distortion, a comparison was made between lesion lengths derived from contrast enhanced MR (CE-MR) images and those obtained from the corresponding DW images. For assessment of image parameters, signal-to-noise ratio (SNR), lesion contrast, and contrast-to-noise ratio (CNR) were calculated. The rs-EPI was superior to ss-EPI in most criteria regarding the qualitative image quality. Anatomical structure distinction, delineation of the lesion, ghosting artifact, and overall image quality were significantly better in rs-EPI. Regarding the geometric distortion, lesion length on ss-EPI was significantly different from that of CE-MR, whereas there were no significant differences between CE-MR and rs-EPI. The rs-EPI was superior to ss-EPI in SNR and CNR. Readout-segmented EPI is superior to ss-EPI in the aspect of image quality in DW MR imaging of the breast

Video retrieval by still-image analysis with ImageMiner

Science.gov (United States)

Kreyss, Jutta; Roeper, M.; Alshuth, Peter; Hermes, Thorsten; Herzog, Otthein

1997-01-01

The large amount of available multimedia information (e.g. videos, audio, images) requires efficient and effective annotation and retrieval methods. As videos start playing a more important role in the frame of multimedia, we want to make these available for content-based retrieval. The ImageMiner-System, which was developed at the University of Bremen in the AI group, is designed for content-based retrieval of single images by a new combination of techniques and methods from computer vision and artificial intelligence. In our approach to make videos available for retrieval in a large database of videos and images there are two necessary steps: First, the detection and extraction of shots from a video, which is done by a histogram based method and second, the construction of the separate frames in a shot to one still single images. This is performed by a mosaicing-technique. The resulting mosaiced image gives a one image visualization of the shot and can be analyzed by the ImageMiner-System. ImageMiner has been tested on several domains, (e.g. landscape images, technical drawings), which cover a wide range of applications.

Stable image acquisition for mobile image processing applications

Science.gov (United States)

Henning, Kai-Fabian; Fritze, Alexander; Gillich, Eugen; Mönks, Uwe; Lohweg, Volker

2015-02-01

Today, mobile devices (smartphones, tablets, etc.) are widespread and of high importance for their users. Their performance as well as versatility increases over time. This leads to the opportunity to use such devices for more specific tasks like image processing in an industrial context. For the analysis of images requirements like image quality (blur, illumination, etc.) as well as a defined relative position of the object to be inspected are crucial. Since mobile devices are handheld and used in constantly changing environments the challenge is to fulfill these requirements. We present an approach to overcome the obstacles and stabilize the image capturing process such that image analysis becomes significantly improved on mobile devices. Therefore, image processing methods are combined with sensor fusion concepts. The approach consists of three main parts. First, pose estimation methods are used to guide a user moving the device to a defined position. Second, the sensors data and the pose information are combined for relative motion estimation. Finally, the image capturing process is automated. It is triggered depending on the alignment of the device and the object as well as the image quality that can be achieved under consideration of motion and environmental effects.

Process defects and in situ monitoring methods in metal powder bed fusion: a review

International Nuclear Information System (INIS)

Grasso, Marco; Colosimo, Bianca Maria

2017-01-01

Despite continuous technological enhancements of metal Additive Manufacturing (AM) systems, the lack of process repeatability and stability still represents a barrier for the industrial breakthrough. The most relevant metal AM applications currently involve industrial sectors (e.g. aerospace and bio-medical) where defects avoidance is fundamental. Because of this, there is the need to develop novel in situ monitoring tools able to keep under control the stability of the process on a layer-by-layer basis, and to detect the onset of defects as soon as possible. On the one hand, AM systems must be equipped with in situ sensing devices able to measure relevant quantities during the process, a.k.a. process signatures. On the other hand, in-process data analytics and statistical monitoring techniques are required to detect and localize the defects in an automated way. This paper reviews the literature and the commercial tools for in situ monitoring of powder bed fusion (PBF) processes. It explores the different categories of defects and their main causes, the most relevant process signatures and the in situ sensing approaches proposed so far. Particular attention is devoted to the development of automated defect detection rules and the study of process control strategies, which represent two critical fields for the development of future smart PBF systems. (paper)

Epithermal neutron beam design for neutron capture therapy at the Power Burst Facility and the Brookhaven Medical Research Reactor

International Nuclear Information System (INIS)

Wheeler, F.J.; Parsons, D.K.; Rushton, B.L.; Nigg, D.W.

1990-01-01

Nuclear design studies have been performed for two reactor-based epithermal neutron beams for cancer treatment by neutron capture therapy (NCT). An intermediate-intensity epithermal beam has been designed and implemented at the Brookhaven Medical Research Reactor (BMRR). Measurements show that the BMRR design predictions for the principal characteristics of this beam are accurate. A canine program for research into the biological effects of NCT is now under way at BMRR. The design for a high-intensity epithermal beam with minimal contamination from undesirable radiation components has been finalized for the Power Burst Facility (PBF) at the Idaho National Engineering Laboratory. This design will be implemented when it is determined that human NCT trials are advisable. The PBF beam will exhibit approximately an order of magnitude improvement in absolute epithermal flux intensity over that available in the BMRR, and its angular distribution and spectral characteristics will be more advantageous for NCT. The combined effects of beam intensity, angular distribution, spectrum, and contaminant level allow the desired tumor radiation dose to be delivered in much shorter times than are possible with the currently available BMRR beam, with a significant reduction (factor of 3 to 5) in collateral dose due to beam contaminants

Process defects and in situ monitoring methods in metal powder bed fusion: a review

Science.gov (United States)

Grasso, Marco; Colosimo, Bianca Maria

2017-04-01

Despite continuous technological enhancements of metal Additive Manufacturing (AM) systems, the lack of process repeatability and stability still represents a barrier for the industrial breakthrough. The most relevant metal AM applications currently involve industrial sectors (e.g. aerospace and bio-medical) where defects avoidance is fundamental. Because of this, there is the need to develop novel in situ monitoring tools able to keep under control the stability of the process on a layer-by-layer basis, and to detect the onset of defects as soon as possible. On the one hand, AM systems must be equipped with in situ sensing devices able to measure relevant quantities during the process, a.k.a. process signatures. On the other hand, in-process data analytics and statistical monitoring techniques are required to detect and localize the defects in an automated way. This paper reviews the literature and the commercial tools for in situ monitoring of powder bed fusion (PBF) processes. It explores the different categories of defects and their main causes, the most relevant process signatures and the in situ sensing approaches proposed so far. Particular attention is devoted to the development of automated defect detection rules and the study of process control strategies, which represent two critical fields for the development of future smart PBF systems.

Quality-based procedures in Ontario: exploring health-care leaders' responses.

Science.gov (United States)

Baxter, Pamela; Cleghorn, Laura; Alvarado, Kim; Cummings, Greta; Kennedy, Deborah; McKey, Colleen; Pfaff, Kathy

2016-01-01

To examine health-care leaders' initial response to the implementation of orthopaedic quality based procedures (QBPs) in hospitals across Ontario, Canada. In 2012, Ontario, Canada shifted 91 hospitals to a patient-based funding (PBF) approach. This approach funds health-care organisations based on the number of patients treated with select procedures known as QBPs. An exploratory descriptive design was employed to better understand health-care leaders' early implementation experiences. Seventy organisational leaders from 20 hospitals participated in six focus groups and four interviews to discuss their initial responses to the implementation of two QBPs (primary unilateral hip replacement and primary unilateral knee replacement). Qualitative data underwent content analysis. Three key major themes emerged; (1) responding to change, (2) leading the change and (3) managing the change. Within each of these themes, barriers and benefits were identified. Leaders are accepting of PBF and QBPs. However, challenges exist that require further exploration including the need for a strong infrastructure, accurate and timely clinical and financial data, and policies to prevent unintended consequences. Implementing QBPs requires careful planning, adequate and appropriate resources, vertical and horizontal communication strategies, and policies to ensure that unintended consequences are avoided and positive outcomes achieved. © 2014 John Wiley & Sons Ltd.

Cardiovascular transition at birth: a physiological sequence.

Science.gov (United States)

Hooper, Stuart B; Te Pas, Arjan B; Lang, Justin; van Vonderen, Jeroen J; Roehr, Charles Christoph; Kluckow, Martin; Gill, Andrew W; Wallace, Euan M; Polglase, Graeme R

2015-05-01

The transition to newborn life at birth involves major cardiovascular changes that are triggered by lung aeration. These include a large increase in pulmonary blood flow (PBF), which is required for pulmonary gas exchange and to replace umbilical venous return as the source of preload for the left heart. Clamping the umbilical cord before PBF increases reduces venous return and preload for the left heart and thereby reduces cardiac output. Thus, if ventilation onset is delayed following cord clamping, the infant is at risk of superimposing an ischemic insult, due to low cardiac output, on top of an asphyxic insult. Much debate has centered on the timing of cord clamping at birth, focusing mainly on the potential for a time-dependent placental to infant blood transfusion. This has prompted recommendations for delayed cord clamping for a set time after birth in infants not requiring resuscitation. However, recent evidence indicates that ventilation onset before cord clamping mitigates the adverse cardiovascular consequences caused by immediate cord clamping. This indicates that the timing of cord clamping should be based on the infant's physiology rather than an arbitrary period of time and that delayed cord clamping may be of greatest benefit to apneic infants.

Power Burst Reactor Facility as an epithermal neutron source for brain cancer therapy

International Nuclear Information System (INIS)

Wheeler, F.J.

1986-01-01

The Power Burst Facility (PBF) reactor is considered for modification to provide an intense, clean source of intermediate-energy (epithermal) neutrons desirable for clinical studies of neutron capture therapy (NCT) for malignant tumors. The modifications include partial replacement of the reflector, installation of a neutron-moderating, shifting region, additional shielding, and penetration of the present concrete shield with a collimating (and optionally) filtering region. The studies have indicated that the reactor, after these modifications, will be safely operable at full power (28 MW) within the acceptable limits of the plant protection systems. The neutron beam exiting from the collimator port is predicted to be of sufficient intensity (approx.10 10 neutrons/cm 2 -s) to provide therapeutic doses in very short irradiation times. The beam would be relatively free of undesirable fast neutrons, thermal neutrons and gamma rays. The calculated neutron energy spectrum and associated gamma rays in the beam were provided as input in simulation studies that used a computer model of a patient with a brain tumor to determine predicted dose rates to the tumor and healthy tissue. The results of this conceptual study indicate an intense, clean beam of epithermal neutrons for NCT clinical trials is attainable in the PBF facility with properly engineered design modifications. 9 refs., 11 figs., 3 tabs

Process Evaluation of AISI 4340 Steel Manufactured by Laser Powder Bed Fusion

Science.gov (United States)

Jelis, Elias; Hespos, Michael R.; Ravindra, Nuggehalli M.

2018-01-01

Laser powder bed fusion (L-PBF) involves the consolidation of metal powder, layer by layer, through laser melting and solidification. In this study, process parameters are optimized for AISI 4340 steel to produce dense and homogeneous structures. The optimized process parameters produce mechanical properties at the center of the build plate that are comparable to wrought in the vertical and horizontal orientations after heat treatment and machining. Four subsequent builds are filled with specimens to evaluate the mechanical behavior as a function of location and orientation. Variations in the mechanical properties are likely due to recoater blade interactions with the powder and uneven gas flow. The results obtained in this study are analyzed to assess the reliability and reproducibility of the process. A different build evaluates the performance of near-net-shaped tensile specimens angled 35°-90° from the build plate surface (horizontal). Ductility measurements and surface roughness vary significantly as a function of the build angle. In the stress-relieved and as-built conditions, the mechanical behavior of vertically oriented specimens exhibits somewhat lower and more variable ductility than horizontally oriented specimens. Therefore, several process variables affect the mechanical properties of parts produced by the L-PBF process.

Spectrally Consistent Satellite Image Fusion with Improved Image Priors

DEFF Research Database (Denmark)

Nielsen, Allan Aasbjerg; Aanæs, Henrik; Jensen, Thomas B.S.

2006-01-01

Here an improvement to our previous framework for satellite image fusion is presented. A framework purely based on the sensor physics and on prior assumptions on the fused image. The contributions of this paper are two fold. Firstly, a method for ensuring 100% spectrally consistency is proposed......, even when more sophisticated image priors are applied. Secondly, a better image prior is introduced, via data-dependent image smoothing....

2017 Gordon Conference on Superconductivity

Energy Technology Data Exchange (ETDEWEB)

Chubukov, Andrey [Univ. of Minnesota, Twin Cities, MN (United States)

2017-11-14

The DOE award was for a 2017 Gordon Research conference on Superconductivity (GRC). The objective of GRC is to interchange the information about the latest theoretical and experimental developments in the area of superconductivity and to select most perspective directions for future research in this area.The goal of the Gordon Conference on Superconductivity is to present and discuss the latest results in the field of modern superconductivity, discuss new ideas and new directions of research in the area. It is a long-standing tradition of the Gordon conference on Superconductivity that the vast majority of participants are junior scientists. Funding for the conference would primarily be used to support junior researchers, particularly from under-represented groups. We had more 10 female speakers, some of them junior researchers, and some funding was used to support these speakers. The conference was held together with Gordon Research Seminar on Superconductivity, where almost all speakers and participants were junior scientists.

Deterministic Design Optimization of Structures in OpenMDAO Framework

Science.gov (United States)

Coroneos, Rula M.; Pai, Shantaram S.

2012-01-01

Nonlinear programming algorithms play an important role in structural design optimization. Several such algorithms have been implemented in OpenMDAO framework developed at NASA Glenn Research Center (GRC). OpenMDAO is an open source engineering analysis framework, written in Python, for analyzing and solving Multi-Disciplinary Analysis and Optimization (MDAO) problems. It provides a number of solvers and optimizers, referred to as components and drivers, which users can leverage to build new tools and processes quickly and efficiently. Users may download, use, modify, and distribute the OpenMDAO software at no cost. This paper summarizes the process involved in analyzing and optimizing structural components by utilizing the framework s structural solvers and several gradient based optimizers along with a multi-objective genetic algorithm. For comparison purposes, the same structural components were analyzed and optimized using CometBoards, a NASA GRC developed code. The reliability and efficiency of the OpenMDAO framework was compared and reported in this report.

The Application of Metal Oxide Nanomaterials for Chemical Sensor Development

Science.gov (United States)

Xu, Jennifer C.; Hunter, Gary W.; Evans, Laura J.; VanderWal, Randy L.; Berger, Gordon M.

2007-01-01

NASA Glenn Research Center (GRC) has been developing miniature chemical sensors for a variety of applications including fire detection, emissions monitoring, fuel leak detection, and environmental monitoring. Smart Lick and Stick sensor technology which integrates a sensor array, electronics, telemetry, and power into one microsystem are being developed. These microsystems require low power consumption for long-term aerospace applications. One approach to decreasing power consumption is the use of nanotechnology. Nanocrystalline tin oxide (SnO2) carbon monoxide (CO) sensors developed previously by this group have been successfully used for fire detection and emissions monitoring. This presentation will briefly review the overall NASA GRC chemical sensor program and discuss our further effort in nanotechnology applications. New carbon dioxide (CO2) sensing material using doped nanocrystalline SnO2 will be discussed. Nanocrystalline SnO2 coated solid electrolyte CO2 sensors and SnO2 nanorod and nanofiber hydrogen (H2) sensors operated at reduced or room temperatures will also be discussed.

Air Breathing Propulsion Controls and Diagnostics Research at NASA Glenn Under NASA Aeronautics Research Mission Programs

Science.gov (United States)

Garg, Sanjay

2015-01-01

The Intelligent Control and Autonomy Branch (ICA) at NASA (National Aeronautics and Space Administration) Glenn Research Center (GRC) in Cleveland, Ohio, is leading and participating in various projects in partnership with other organizations within GRC and across NASA, the U.S. aerospace industry, and academia to develop advanced controls and health management technologies that will help meet the goals of the NASA Aeronautics Research Mission Directorate (ARMD) Programs. These efforts are primarily under the various projects under the Advanced Air Vehicles Program (AAVP), Airspace Operations and Safety Program (AOSP) and Transformative Aeronautics Concepts Program (TAC). The ICA Branch is focused on advancing the state-of-the-art of aero-engine control and diagnostics technologies to help improve aviation safety, increase efficiency, and enable operation with reduced emissions. This paper describes the various ICA research efforts under the NASA Aeronautics Research Mission Programs with a summary of motivation, background, technical approach, and recent accomplishments for each of the research tasks.

NASA Lewis Steady-State Heat Pipe Code Architecture

Science.gov (United States)

Mi, Ye; Tower, Leonard K.

2013-01-01

NASA Glenn Research Center (GRC) has developed the LERCHP code. The PC-based LERCHP code can be used to predict the steady-state performance of heat pipes, including the determination of operating temperature and operating limits which might be encountered under specified conditions. The code contains a vapor flow algorithm which incorporates vapor compressibility and axially varying heat input. For the liquid flow in the wick, Darcy s formula is employed. Thermal boundary conditions and geometric structures can be defined through an interactive input interface. A variety of fluid and material options as well as user defined options can be chosen for the working fluid, wick, and pipe materials. This report documents the current effort at GRC to update the LERCHP code for operating in a Microsoft Windows (Microsoft Corporation) environment. A detailed analysis of the model is presented. The programming architecture for the numerical calculations is explained and flowcharts of the key subroutines are given

Image quality dependence on image processing software in ...

African Journals Online (AJOL)

Image quality dependence on image processing software in computed radiography. ... Agfa CR readers use MUSICA software, and an upgrade with significantly different image ... Full Text: EMAIL FREE FULL TEXT EMAIL FREE FULL TEXT

Parallel MR imaging.

Science.gov (United States)

Deshmane, Anagha; Gulani, Vikas; Griswold, Mark A; Seiberlich, Nicole

2012-07-01

Parallel imaging is a robust method for accelerating the acquisition of magnetic resonance imaging (MRI) data, and has made possible many new applications of MR imaging. Parallel imaging works by acquiring a reduced amount of k-space data with an array of receiver coils. These undersampled data can be acquired more quickly, but the undersampling leads to aliased images. One of several parallel imaging algorithms can then be used to reconstruct artifact-free images from either the aliased images (SENSE-type reconstruction) or from the undersampled data (GRAPPA-type reconstruction). The advantages of parallel imaging in a clinical setting include faster image acquisition, which can be used, for instance, to shorten breath-hold times resulting in fewer motion-corrupted examinations. In this article the basic concepts behind parallel imaging are introduced. The relationship between undersampling and aliasing is discussed and two commonly used parallel imaging methods, SENSE and GRAPPA, are explained in detail. Examples of artifacts arising from parallel imaging are shown and ways to detect and mitigate these artifacts are described. Finally, several current applications of parallel imaging are presented and recent advancements and promising research in parallel imaging are briefly reviewed. Copyright © 2012 Wiley Periodicals, Inc.

Medical Imaging System

Science.gov (United States)

1991-01-01

The MD Image System, a true-color image processing system that serves as a diagnostic aid and tool for storage and distribution of images, was developed by Medical Image Management Systems, Huntsville, AL, as a "spinoff from a spinoff." The original spinoff, Geostar 8800, developed by Crystal Image Technologies, Huntsville, incorporates advanced UNIX versions of ELAS (developed by NASA's Earth Resources Laboratory for analysis of Landsat images) for general purpose image processing. The MD Image System is an application of this technology to a medical system that aids in the diagnosis of cancer, and can accept, store and analyze images from other sources such as Magnetic Resonance Imaging.

Retinal imaging and image analysis

NARCIS (Netherlands)

Abramoff, M.D.; Garvin, Mona K.; Sonka, Milan

2010-01-01

Many important eye diseases as well as systemic diseases manifest themselves in the retina. While a number of other anatomical structures contribute to the process of vision, this review focuses on retinal imaging and image analysis. Following a brief overview of the most prevalent causes of

Imaging of melorheostosis : emphasis on MR imaging findings

Energy Technology Data Exchange (ETDEWEB)

Lee, Chang Hyon; Lee, Sang Kwon; Kim, Jong Yeol; Shin, Tae Bum; Kim, Young Whan; Pak, Hyo Yong; Kim, Yong Joo; Kang, Duk Sik [College of Medicine, Kyungpook National University, Taegu (Korea, Republic of); Lee, Yeong Hwan [College of Medicine, Catholic University of Taegu-Hyosung, Taegu (Korea, Republic of); Byun, Kyung Hwan [Kumi CHA General Hospital, College of Medicine, Pochon CHA University, Kumi (Korea, Republic of)

2000-02-01

To evaluate the usefulness of various radiographic imaging modalities in the diagnosis and characterization of melorheostosis. We retrospectively evaluated the plain film (n=3D8), computed tomographic (CT) imaging (n=3D5) and magnetic resonance (MR) imaging (n=3D5) findings of eight patients with melorheostosis diagnosed by bone biopsy (n=3D4) and characteristic radiographic findings (n=3D8). MR images were obtained with a 1.5-T scanner focused on the region of maximal radiographic abnormality. Pulse sequences include T1-weighted SE. T2-weighted fast SE (n=3D5) and postcontrast imaging (n=3D4). In order to define subtle enhancement of the lesions, subtraction MR images were obtained in one case. Imaging findings were analyzed with particular emphasis on the distribution lesions along the sclerotome, differential radiographic findings between diaphyseal and metaepiphyseal lesions of the long bones, as seen on plain radiographs, and the density and signal characteristics of hyperostotic lesions, as seen on CT and MR images. Characteristic distribution along the sclerotome was identified in five of eight cases mainly along C6 and 7 (n=3D2) and L3, 4 and 5 (n=3D3) sclerotomes. In diaphyseal melorherostosis (8/8), a characteristic finding, i.e., a wax flowing down from the candle, was identified on plain radiographs. In all three patients with metaepiphyseal melorheostosis (3/8), multiple round or oval hyperostotic lesions were seen in the epipysis and metaphysis of the long bones. On CT, the marrow cavity was partly obliterated by hyperostotic lesions in all five patients with endosteal hyperostosis. Among these, central ground glass opacity with a sclerotic rim was seen in three patients. Periosteal hyperostosis was seen in two of five cases, being visualized as irregular excrescence in the periosteal region and surrounding soft tissue. Individual hyperostosis was visualized as hypointense on T1-weighted images and as a hyperintense center with a surrounding

COMPARISON OF IMAGE ENHANCEMENT METHODS FOR CHROMOSOME KARYOTYPE IMAGE ENHANCEMENT

Directory of Open Access Journals (Sweden)

Dewa Made Sri Arsa

2017-02-01

Full Text Available The chromosome is a set of DNA structure that carry information about our life. The information can be obtained through Karyotyping. The process requires a clear image so the chromosome can be evaluate well. Preprocessing have to be done on chromosome images that is image enhancement. The process starts with image background removing. The image will be cleaned background color. The next step is image enhancement. This paper compares several methods for image enhancement. We evaluate some method in image enhancement like Histogram Equalization (HE, Contrast-limiting Adaptive Histogram Equalization (CLAHE, Histogram Equalization with 3D Block Matching (HE+BM3D, and basic image enhancement, unsharp masking. We examine and discuss the best method for enhancing chromosome image. Therefore, to evaluate the methods, the original image was manipulated by the addition of some noise and blur. Peak Signal-to-noise Ratio (PSNR and Structural Similarity Index (SSIM are used to examine method performance. The output of enhancement method will be compared with result of Professional software for karyotyping analysis named Ikaros MetasystemT M . Based on experimental results, HE+BM3D method gets a stable result on both scenario noised and blur image.

Quantitative assessment of dynamic PET imaging data in cancer imaging.

Science.gov (United States)

Muzi, Mark; O'Sullivan, Finbarr; Mankoff, David A; Doot, Robert K; Pierce, Larry A; Kurland, Brenda F; Linden, Hannah M; Kinahan, Paul E

2012-11-01

Clinical imaging in positron emission tomography (PET) is often performed using single-time-point estimates of tracer uptake or static imaging that provides a spatial map of regional tracer concentration. However, dynamic tracer imaging can provide considerably more information about in vivo biology by delineating both the temporal and spatial pattern of tracer uptake. In addition, several potential sources of error that occur in static imaging can be mitigated. This review focuses on the application of dynamic PET imaging to measuring regional cancer biologic features and especially in using dynamic PET imaging for quantitative therapeutic response monitoring for cancer clinical trials. Dynamic PET imaging output parameters, particularly transport (flow) and overall metabolic rate, have provided imaging end points for clinical trials at single-center institutions for years. However, dynamic imaging poses many challenges for multicenter clinical trial implementations from cross-center calibration to the inadequacy of a common informatics infrastructure. Underlying principles and methodology of PET dynamic imaging are first reviewed, followed by an examination of current approaches to dynamic PET image analysis with a specific case example of dynamic fluorothymidine imaging to illustrate the approach. Copyright © 2012 Elsevier Inc. All rights reserved.

Imaging angiogenesis.

Science.gov (United States)

Charnley, Natalie; Donaldson, Stephanie; Price, Pat

2009-01-01

There is a need for direct imaging of effects on tumor vasculature in assessment of response to antiangiogenic drugs and vascular disrupting agents. Imaging tumor vasculature depends on differences in permeability of vasculature of tumor and normal tissue, which cause changes in penetration of contrast agents. Angiogenesis imaging may be defined in terms of measurement of tumor perfusion and direct imaging of the molecules involved in angiogenesis. In addition, assessment of tumor hypoxia will give an indication of tumor vasculature. The range of imaging techniques available for these processes includes positron emission tomography (PET), dynamic contrast-enhanced magnetic resonance imaging (DCE-MRI), perfusion computed tomography (CT), and ultrasound (US).

X-ray volumetric imaging in image-guided radiotherapy: The new standard in on-treatment imaging

International Nuclear Information System (INIS)

McBain, Catherine A.; Henry, Ann M.; Sykes, Jonathan; Amer, Ali; Marchant, Tom; Moore, Christopher M.; Davies, Julie; Stratford, Julia; McCarthy, Claire; Porritt, Bridget; Williams, Peter; Khoo, Vincent S.; Price, Pat

2006-01-01

Purpose: X-ray volumetric imaging (XVI) for the first time allows for the on-treatment acquisition of three-dimensional (3D) kV cone beam computed tomography (CT) images. Clinical imaging using the Synergy System (Elekta, Crawley, UK) commenced in July 2003. This study evaluated image quality and dose delivered and assessed clinical utility for treatment verification at a range of anatomic sites. Methods and Materials: Single XVIs were acquired from 30 patients undergoing radiotherapy for tumors at 10 different anatomic sites. Patients were imaged in their setup position. Radiation doses received were measured using TLDs on the skin surface. The utility of XVI in verifying target volume coverage was qualitatively assessed by experienced clinicians. Results: X-ray volumetric imaging acquisition was completed in the treatment position at all anatomic sites. At sites where a full gantry rotation was not possible, XVIs were reconstructed from projection images acquired from partial rotations. Soft-tissue definition of organ boundaries allowed direct assessment of 3D target volume coverage at all sites. Individual image quality depended on both imaging parameters and patient characteristics. Radiation dose ranged from 0.003 Gy in the head to 0.03 Gy in the pelvis. Conclusions: On-treatment XVI provided 3D verification images with soft-tissue definition at all anatomic sites at acceptably low radiation doses. This technology sets a new standard in treatment verification and will facilitate novel adaptive radiotherapy techniques

Evaluation of multimodality imaging using image fusion with ultrasound tissue elasticity imaging in an experimental animal model.

Science.gov (United States)

Paprottka, P M; Zengel, P; Cyran, C C; Ingrisch, M; Nikolaou, K; Reiser, M F; Clevert, D A

2014-01-01

To evaluate the ultrasound tissue elasticity imaging by comparison to multimodality imaging using image fusion with Magnetic Resonance Imaging (MRI) and conventional grey scale imaging with additional elasticity-ultrasound in an experimental small-animal-squamous-cell carcinoma-model for the assessment of tissue morphology. Human hypopharynx carcinoma cells were subcutaneously injected into the left flank of 12 female athymic nude rats. After 10 days (SD ± 2) of subcutaneous tumor growth, sonographic grey scale including elasticity imaging and MRI measurements were performed using a high-end ultrasound system and a 3T MR. For image fusion the contrast-enhanced MRI DICOM data set was uploaded in the ultrasonic device which has a magnetic field generator, a linear array transducer (6-15 MHz) and a dedicated software package (GE Logic E9), that can detect transducers by means of a positioning system. Conventional grey scale and elasticity imaging were integrated in the image fusion examination. After successful registration and image fusion the registered MR-images were simultaneously shown with the respective ultrasound sectional plane. Data evaluation was performed using the digitally stored video sequence data sets by two experienced radiologist using a modified Tsukuba Elasticity score. The colors "red and green" are assigned for an area of soft tissue, "blue" indicates hard tissue. In all cases a successful image fusion and plan registration with MRI and ultrasound imaging including grey scale and elasticity imaging was possible. The mean tumor volume based on caliper measurements in 3 dimensions was ~323 mm3. 4/12 rats were evaluated with Score I, 5/12 rates were evaluated with Score II, 3/12 rates were evaluated with Score III. There was a close correlation in the fused MRI with existing small necrosis in the tumor. None of the scored II or III lesions was visible by conventional grey scale. The comparison of ultrasound tissue elasticity imaging enables a

Development of the neutron filters for JET gamma-ray cameras

International Nuclear Information System (INIS)

Soare, S.; Curuia, M.; Anghel, M.; Constantin, M.; David, E.; Kiptily, V.; Prior, P.; Edlington, T.; Griph, S.; Krivchenkov, Y.; Popovichev, S.; Riccardo, V.; Syme, B; Thompson, V.; Murari, A.; Zoita, V.; Bonheure, G.; Le Guern

2007-01-01

The JET gamma-ray camera diagnostics have already provided valuable information on the gamma-ray imaging of fast ion evaluation in JET plasmas. The JET Gamma-Ray Cameras (GRC) upgrade project deals with the design of appropriate neutron/gamma-ray filters ('neutron attenuaters').The main design parameter was the neutron attenuation factor. The two design solutions, that have been finally chosen and developed at the level of scheme design, consist of: a) one quasi-crescent shaped neutron attenuator (for the horizontal camera) and b) two quasi-trapezoid shaped neutron attenuators (for the vertical one). Various neutron-attenuating materials have been considered (lithium hydride with natural isotopic composition and 6 Li enriched, light and heavy water, polyethylene). Pure light water was finally chosen as the attenuating material for the JET gamma-ray cameras. FEA methods used to evaluate the behaviour of the filter casings under the loadings (internal hydrostatic pressure, torques) have proven the stability of the structure. (authors)

Matching rendered and real world images by digital image processing

Science.gov (United States)

Mitjà, Carles; Bover, Toni; Bigas, Miquel; Escofet, Jaume

2010-05-01

Recent advances in computer-generated images (CGI) have been used in commercial and industrial photography providing a broad scope in product advertising. Mixing real world images with those rendered from virtual space software shows a more or less visible mismatching between corresponding image quality performance. Rendered images are produced by software which quality performance is only limited by the resolution output. Real world images are taken with cameras with some amount of image degradation factors as lens residual aberrations, diffraction, sensor low pass anti aliasing filters, color pattern demosaicing, etc. The effect of all those image quality degradation factors can be characterized by the system Point Spread Function (PSF). Because the image is the convolution of the object by the system PSF, its characterization shows the amount of image degradation added to any taken picture. This work explores the use of image processing to degrade the rendered images following the parameters indicated by the real system PSF, attempting to match both virtual and real world image qualities. The system MTF is determined by the slanted edge method both in laboratory conditions and in the real picture environment in order to compare the influence of the working conditions on the device performance; an approximation to the system PSF is derived from the two measurements. The rendered images are filtered through a Gaussian filter obtained from the taking system PSF. Results with and without filtering are shown and compared measuring the contrast achieved in different final image regions.

Quantum Image Encryption Algorithm Based on Image Correlation Decomposition

Science.gov (United States)

Hua, Tianxiang; Chen, Jiamin; Pei, Dongju; Zhang, Wenquan; Zhou, Nanrun

2015-02-01

A novel quantum gray-level image encryption and decryption algorithm based on image correlation decomposition is proposed. The correlation among image pixels is established by utilizing the superposition and measurement principle of quantum states. And a whole quantum image is divided into a series of sub-images. These sub-images are stored into a complete binary tree array constructed previously and then randomly performed by one of the operations of quantum random-phase gate, quantum revolving gate and Hadamard transform. The encrypted image can be obtained by superimposing the resulting sub-images with the superposition principle of quantum states. For the encryption algorithm, the keys are the parameters of random phase gate, rotation angle, binary sequence and orthonormal basis states. The security and the computational complexity of the proposed algorithm are analyzed. The proposed encryption algorithm can resist brute force attack due to its very large key space and has lower computational complexity than its classical counterparts.

Corner-point criterion for assessing nonlinear image processing imagers

Science.gov (United States)

Landeau, Stéphane; Pigois, Laurent; Foing, Jean-Paul; Deshors, Gilles; Swiathy, Greggory

2017-10-01

Range performance modeling of optronics imagers attempts to characterize the ability to resolve details in the image. Today, digital image processing is systematically used in conjunction with the optoelectronic system to correct its defects or to exploit tiny detection signals to increase performance. In order to characterize these processing having adaptive and non-linear properties, it becomes necessary to stimulate the imagers with test patterns whose properties are similar to the actual scene image ones, in terms of dynamic range, contours, texture and singular points. This paper presents an approach based on a Corner-Point (CP) resolution criterion, derived from the Probability of Correct Resolution (PCR) of binary fractal patterns. The fundamental principle lies in the respectful perception of the CP direction of one pixel minority value among the majority value of a 2×2 pixels block. The evaluation procedure considers the actual image as its multi-resolution CP transformation, taking the role of Ground Truth (GT). After a spatial registration between the degraded image and the original one, the degradation is statistically measured by comparing the GT with the degraded image CP transformation, in terms of localized PCR at the region of interest. The paper defines this CP criterion and presents the developed evaluation techniques, such as the measurement of the number of CP resolved on the target, the transformation CP and its inverse transform that make it possible to reconstruct an image of the perceived CPs. Then, this criterion is compared with the standard Johnson criterion, in the case of a linear blur and noise degradation. The evaluation of an imaging system integrating an image display and a visual perception is considered, by proposing an analysis scheme combining two methods: a CP measurement for the highly non-linear part (imaging) with real signature test target and conventional methods for the more linear part (displaying). The application to

Volumetric CT-images improve testing of radiological image interpretation skills

Energy Technology Data Exchange (ETDEWEB)

Ravesloot, Cécile J., E-mail: C.J.Ravesloot@umcutrecht.nl [Radiology Department at University Medical Center Utrecht, Heidelberglaan 100, 3508 GA Utrecht, Room E01.132 (Netherlands); Schaaf, Marieke F. van der, E-mail: M.F.vanderSchaaf@uu.nl [Department of Pedagogical and Educational Sciences at Utrecht University, Heidelberglaan 1, 3584 CS Utrecht (Netherlands); Schaik, Jan P.J. van, E-mail: J.P.J.vanSchaik@umcutrecht.nl [Radiology Department at University Medical Center Utrecht, Heidelberglaan 100, 3508 GA Utrecht, Room E01.132 (Netherlands); Cate, Olle Th.J. ten, E-mail: T.J.tenCate@umcutrecht.nl [Center for Research and Development of Education at University Medical Center Utrecht, Heidelberglaan 100, 3508 GA Utrecht (Netherlands); Gijp, Anouk van der, E-mail: A.vanderGijp-2@umcutrecht.nl [Radiology Department at University Medical Center Utrecht, Heidelberglaan 100, 3508 GA Utrecht, Room E01.132 (Netherlands); Mol, Christian P., E-mail: C.Mol@umcutrecht.nl [Image Sciences Institute at University Medical Center Utrecht, Heidelberglaan 100, 3508 GA Utrecht (Netherlands); Vincken, Koen L., E-mail: K.Vincken@umcutrecht.nl [Image Sciences Institute at University Medical Center Utrecht, Heidelberglaan 100, 3508 GA Utrecht (Netherlands)

2015-05-15

Rationale and objectives: Current radiology practice increasingly involves interpretation of volumetric data sets. In contrast, most radiology tests still contain only 2D images. We introduced a new testing tool that allows for stack viewing of volumetric images in our undergraduate radiology program. We hypothesized that tests with volumetric CT-images enhance test quality, in comparison with traditional completely 2D image-based tests, because they might better reflect required skills for clinical practice. Materials and methods: Two groups of medical students (n = 139; n = 143), trained with 2D and volumetric CT-images, took a digital radiology test in two versions (A and B), each containing both 2D and volumetric CT-image questions. In a questionnaire, they were asked to comment on the representativeness for clinical practice, difficulty and user-friendliness of the test questions and testing program. Students’ test scores and reliabilities, measured with Cronbach's alpha, of 2D and volumetric CT-image tests were compared. Results: Estimated reliabilities (Cronbach's alphas) were higher for volumetric CT-image scores (version A: .51 and version B: .54), than for 2D CT-image scores (version A: .24 and version B: .37). Participants found volumetric CT-image tests more representative of clinical practice, and considered them to be less difficult than volumetric CT-image questions. However, in one version (A), volumetric CT-image scores (M 80.9, SD 14.8) were significantly lower than 2D CT-image scores (M 88.4, SD 10.4) (p < .001). The volumetric CT-image testing program was considered user-friendly. Conclusion: This study shows that volumetric image questions can be successfully integrated in students’ radiology testing. Results suggests that the inclusion of volumetric CT-images might improve the quality of radiology tests by positively impacting perceived representativeness for clinical practice and increasing reliability of the test.

Nuclear imaging in the realm of medical imaging

International Nuclear Information System (INIS)

Deconinck, Frank

2003-01-01

In medical imaging, information concerning the anatomy or biological processes of a patient is detected and presented on film or screen for interpretation by a reader. The information flow from patient to reader optimally implies: - the emission, transmission or reflection of information carriers, typically photons or sound waves, which have to be correctly modulated by patient information through interactions in the patient; - their detection by adequate imaging equipment preserving essential spectral, spatial and/or temporal information; - the presentation of the information in the most perceivable way; - the observation by an unbiased and trained expert. In reality, only an approximation to this optimal situation is achieved. It is the goal of R and D in the medical imaging field to approach the optimum as much as possible within societal constraints such as patient risk and comfort, economics, etc. First, the basic physical concepts underlying the imaging process will be introduced. Different imaging modalities will then be situated in the realm of medical imaging with some emphasis on nuclear imaging

Image city

DEFF Research Database (Denmark)

2003-01-01

Image city exhibition explores a condition of mediation, through a focus on image and sound narratives with a point of departure on a number of Asian cities.......Image city exhibition explores a condition of mediation, through a focus on image and sound narratives with a point of departure on a number of Asian cities....

Analysis of image plane's Illumination in Image-forming System

International Nuclear Information System (INIS)

Duan Lihua; Zeng Yan'an; Zhang Nanyangsheng; Wang Zhiguo; Yin Shiliang

2011-01-01

In the detection of optical radiation, the detecting accuracy is affected by optic power distribution of the detector's surface to a large extent. In addition, in the image-forming system, the quality of the image is greatly determined by the uniformity of the image's illumination distribution. However, in the practical optical system, affected by the factors such as field of view, false light and off axis and so on, the distribution of the image's illumination tends to be non uniform, so it is necessary to discuss the image plane's illumination in image-forming systems. In order to analyze the characteristics of the image-forming system at a full range, on the basis of photometry, the formulas to calculate the illumination of the imaging plane have been summarized by the numbers. Moreover, the relationship between the horizontal offset of the light source and the illumination of the image has been discussed in detail. After that, the influence of some key factors such as aperture angle, off-axis distance and horizontal offset on illumination of the image has been brought forward. Through numerical simulation, various theoretical curves of those key factors have been given. The results of the numerical simulation show that it is recommended to aggrandize the diameter of the exit pupil to increase the illumination of the image. The angle of view plays a negative role in the illumination distribution of the image, that is, the uniformity of the illumination distribution can be enhanced by compressing the angle of view. Lastly, it is proved that telecentric optical design is an effective way to advance the uniformity of the illumination distribution.

Correlation of adiposity indices with cardiovascular disease risk factors in healthy adults of Singapore: a cross-sectional study

OpenAIRE

Bi, Xinyan; Tey, Siew Ling; Leong, Claudia; Quek, Rina; Loo, Yi Ting; Henry, Christiani Jeyakumar

2016-01-01

Background Obesity has long been highlighted for its association with increased incidence of cardiovascular disease (CVD). Nonetheless, the best adiposity indices to evaluate the CVD risk factors remain contentious and few studies have been performed in Asian populations. In the present study, we compared the association strength of percent body fat (PBF) to indirect anthropometric measures of general adiposity (body mass index (BMI) and body adiposity index (BAI)) and central adiposity (wais...

Fast processing of foreign fiber images by image blocking

OpenAIRE

Yutao Wu; Daoliang Li; Zhenbo Li; Wenzhu Yang

2014-01-01

In the textile industry, it is always the case that cotton products are constitutive of many types of foreign fibers which affect the overall quality of cotton products. As the foundation of the foreign fiber automated inspection, image process exerts a critical impact on the process of foreign fiber identification. This paper presents a new approach for the fast processing of foreign fiber images. This approach includes five main steps, image block, image pre-decision, image background extra...

Image processing on the image with pixel noise bits removed

Science.gov (United States)

Chuang, Keh-Shih; Wu, Christine

1992-06-01

Our previous studies used statistical methods to assess the noise level in digital images of various radiological modalities. We separated the pixel data into signal bits and noise bits and demonstrated visually that the removal of the noise bits does not affect the image quality. In this paper we apply image enhancement techniques on noise-bits-removed images and demonstrate that the removal of noise bits has no effect on the image property. The image processing techniques used are gray-level look up table transformation, Sobel edge detector, and 3-D surface display. Preliminary results show no noticeable difference between original image and noise bits removed image using look up table operation and Sobel edge enhancement. There is a slight enhancement of the slicing artifact in the 3-D surface display of the noise bits removed image.

Hybrid Image Fusion for Sharpness Enhancement of Multi-Spectral Lunar Images

Science.gov (United States)

Awumah, Anna; Mahanti, Prasun; Robinson, Mark

2016-10-01

Image fusion enhances the sharpness of a multi-spectral (MS) image by incorporating spatial details from a higher-resolution panchromatic (Pan) image [1,2]. Known applications of image fusion for planetary images are rare, although image fusion is well-known for its applications to Earth-based remote sensing. In a recent work [3], six different image fusion algorithms were implemented and their performances were verified with images from the Lunar Reconnaissance Orbiter (LRO) Camera. The image fusion procedure obtained a high-resolution multi-spectral (HRMS) product from the LRO Narrow Angle Camera (used as Pan) and LRO Wide Angle Camera (used as MS) images. The results showed that the Intensity-Hue-Saturation (IHS) algorithm results in a high-spatial quality product while the Wavelet-based image fusion algorithm best preserves spectral quality among all the algorithms. In this work we show the results of a hybrid IHS-Wavelet image fusion algorithm when applied to LROC MS images. The hybrid method provides the best HRMS product - both in terms of spatial resolution and preservation of spectral details. Results from hybrid image fusion can enable new science and increase the science return from existing LROC images.[1] Pohl, Cle, and John L. Van Genderen. "Review article multisensor image fusion in remote sensing: concepts, methods and applications." International journal of remote sensing 19.5 (1998): 823-854.[2] Zhang, Yun. "Understanding image fusion." Photogramm. Eng. Remote Sens 70.6 (2004): 657-661.[3] Mahanti, Prasun et al. "Enhancement of spatial resolution of the LROC Wide Angle Camera images." Archives, XXIII ISPRS Congress Archives (2016).

Rapid MR imaging

International Nuclear Information System (INIS)

Edelman, R.R.; Buxton, R.B.; Brady, T.J.

1988-01-01

Conventional magnetic resonance (MR) imaging methods typically require several minutes to produce an image, but the periods of respiration, cardiac motion and peristalsis are on the order of seconds or less. The need to reduce motion artifact, as well as the need to reduce imaging time for patient comfort and efficiency, have provided a strong impetus for the development of rapid imaging methods. For abdominal imaging, motion artifacts due to respiration can be significantly reduced by collecting the entire image during one breath hold. For other applications, such as following the kinetics of administered contrast agents, rapid imaging is essential to achieve adequate time resolution. A shorter imaging time entails a cost in image signal/noise (S/N), but improvements in recent years in magnet homogeneity, gradient and radiofrequency coil design have led to steady improvements in S/N and consequently in image quality. For many chemical applications the available S/N is greater than needed, and a trade-off of lower S/N for a shorter imaging time is acceptable. In this chapter, the authors consider the underlying principles of rapid imaging as well as clinical applications of these methods. The bulk of this review concentrates on short TR imaging, but methods that provide for a more modest decrease in imaging time as well as or those that dramatically shorten the imaging time to tens of milliseconds are also discussed

Molecular photoacoustic imaging

Directory of Open Access Journals (Sweden)

Frogh Jafarian Dehkordi

2015-04-01

Full Text Available Background: Hybrid imaging modalities which simultaneously benefit from capabilities of combined modalities provides an opportunity to modify quality of the images which can be obtained by each of the combined imaging systems. One of the imaging modalities, emerged in medical research area as a hybrid of ultrasound imaging and optical imaging, is photoacoustic imaging which apply ultrasound wave generated by tissue, after receiving laser pulse, to produce medical images. Materials and Methods: In this review, using keywords such as photoacoustic, optoacoustic, laser-ultrasound, thermoacoustic at databases such as PubMed and ISI, studies performed in the field of photoacoustic and related findings were evaluated. Results: Photoacoustic imaging, acquiring images with high contrast and desired resolution, provides an opportunity to perform physiologic and anatomic studies. Because this technique does not use ionizing radiation, it is not restricted by the limitation of the ionizing-based imaging systems therefore it can be used noninvasively to make images from cell, vessels, whole body imaging of the animal and distinguish tumor from normal tissue. Conclusion: Photoacoustic imaging is a new method in preclinical researches which can be used in various physiologic and anatomic studies. This method, because of application of non-ionizing radiation, may resolve limitation of radiation based method in diagnostic assessments.

Image perception and image processing

International Nuclear Information System (INIS)

Wackenheim, A.

1987-01-01

The author develops theoretical and practical models of image perception and image processing, based on phenomenology and structuralism and leading to original perception: fundamental for a positivistic approach of research work for the development of artificial intelligence that will be able in an automated system fo 'reading' X-ray pictures. (orig.) [de

Image perception and image processing

Energy Technology Data Exchange (ETDEWEB)

Wackenheim, A.

1987-01-01

The author develops theoretical and practical models of image perception and image processing, based on phenomenology and structuralism and leading to original perception: fundamental for a positivistic approach of research work for the development of artificial intelligence that will be able in an automated system fo 'reading' X-ray pictures.

Image-adaptive and robust digital wavelet-domain watermarking for images

Science.gov (United States)

Zhao, Yi; Zhang, Liping

2018-03-01

We propose a new frequency domain wavelet based watermarking technique. The key idea of our scheme is twofold: multi-tier solution representation of image and odd-even quantization embedding/extracting watermark. Because many complementary watermarks need to be hidden, the watermark image designed is image-adaptive. The meaningful and complementary watermark images was embedded into the original image (host image) by odd-even quantization modifying coefficients, which was selected from the detail wavelet coefficients of the original image, if their magnitudes are larger than their corresponding Just Noticeable Difference thresholds. The tests show good robustness against best-known attacks such as noise addition, image compression, median filtering, clipping as well as geometric transforms. Further research may improve the performance by refining JND thresholds.

Optimal image resolution for digital storage of radiotherapy-planning images

International Nuclear Information System (INIS)

Baba, Yuji; Furusawa, Mitsuhiro; Murakami, Ryuji; Baba, Takashi; Yokoyama, Toshimi; Nishimura, Ryuichi; Takahashi, Mutsumasa

1998-01-01

Purpose: To evaluate the quality of digitized radiation-planning images at different resolution and to determine the optimal resolution for digital storage. Methods and Materials: Twenty-five planning films were scanned and digitized using a film scanner at a resolution of 72 dots per inch (dpi) with 8-bit depth. The resolution of scanned images was reduced to 48, 36, 24, and 18 dpi using computer software. Image qualities of these five images (72, 48, 36, 24, and 18 dpi) were evaluated and given scores (4 = excellent; 3 = good; 2 = fair; and 1 = poor) by three radiation oncologists. An image data compression algorithm by the Joint Photographic Experts Group (JPEG) (not reversible and some information will be lost) was also evaluated. Results: The scores of digitized images with 72, 48, 36, 24, and 17 dpi resolution were 3.8 ± 0.3, 3.5 ± 0.3, 3.3 ± 0.5, 2.7 ± 0.5, and 1.6 ± 0.3, respectively. The quality of 36-dpi images were definitely worse compared to 72-dpi images, but were good enough as planning films. Digitized planning images with 72- and 36-dpi resolution requires about 800 and 200 KBytes, respectively. The JPEG compression algorithm produces little degradation in 36-dpi images at compression ratios of 5:1. Conclusion: The quality of digitized images with 36-dpi resolution was good enough as radiation-planning images and required 200 KBytes/image

Quantitative imaging features: extension of the oncology medical image database

Science.gov (United States)

Patel, M. N.; Looney, P. T.; Young, K. C.; Halling-Brown, M. D.

2015-03-01

Radiological imaging is fundamental within the healthcare industry and has become routinely adopted for diagnosis, disease monitoring and treatment planning. With the advent of digital imaging modalities and the rapid growth in both diagnostic and therapeutic imaging, the ability to be able to harness this large influx of data is of paramount importance. The Oncology Medical Image Database (OMI-DB) was created to provide a centralized, fully annotated dataset for research. The database contains both processed and unprocessed images, associated data, and annotations and where applicable expert determined ground truths describing features of interest. Medical imaging provides the ability to detect and localize many changes that are important to determine whether a disease is present or a therapy is effective by depicting alterations in anatomic, physiologic, biochemical or molecular processes. Quantitative imaging features are sensitive, specific, accurate and reproducible imaging measures of these changes. Here, we describe an extension to the OMI-DB whereby a range of imaging features and descriptors are pre-calculated using a high throughput approach. The ability to calculate multiple imaging features and data from the acquired images would be valuable and facilitate further research applications investigating detection, prognosis, and classification. The resultant data store contains more than 10 million quantitative features as well as features derived from CAD predictions. Theses data can be used to build predictive models to aid image classification, treatment response assessment as well as to identify prognostic imaging biomarkers.

Enhancement system of nighttime infrared video image and visible video image

Science.gov (United States)

Wang, Yue; Piao, Yan

2016-11-01

Visibility of Nighttime video image has a great significance for military and medicine areas, but nighttime video image has so poor quality that we can't recognize the target and background. Thus we enhance the nighttime video image by fuse infrared video image and visible video image. According to the characteristics of infrared and visible images, we proposed improved sift algorithm andαβ weighted algorithm to fuse heterologous nighttime images. We would deduced a transfer matrix from improved sift algorithm. The transfer matrix would rapid register heterologous nighttime images. And theαβ weighted algorithm can be applied in any scene. In the video image fusion system, we used the transfer matrix to register every frame and then used αβ weighted method to fuse every frame, which reached the time requirement soft video. The fused video image not only retains the clear target information of infrared video image, but also retains the detail and color information of visible video image and the fused video image can fluency play.

An enhanced approach for biomedical image restoration using image fusion techniques

Science.gov (United States)

Karam, Ghada Sabah; Abbas, Fatma Ismail; Abood, Ziad M.; Kadhim, Kadhim K.; Karam, Nada S.

2018-05-01

Biomedical image is generally noisy and little blur due to the physical mechanisms of the acquisition process, so one of the common degradations in biomedical image is their noise and poor contrast. The idea of biomedical image enhancement is to improve the quality of the image for early diagnosis. In this paper we are using Wavelet Transformation to remove the Gaussian noise from biomedical images: Positron Emission Tomography (PET) image and Radiography (Radio) image, in different color spaces (RGB, HSV, YCbCr), and we perform the fusion of the denoised images resulting from the above denoising techniques using add image method. Then some quantive performance metrics such as signal -to -noise ratio (SNR), peak signal-to-noise ratio (PSNR), and Mean Square Error (MSE), etc. are computed. Since this statistical measurement helps in the assessment of fidelity and image quality. The results showed that our approach can be applied of Image types of color spaces for biomedical images.

Multimodality imaging techniques.

Science.gov (United States)

Martí-Bonmatí, Luis; Sopena, Ramón; Bartumeus, Paula; Sopena, Pablo

2010-01-01

In multimodality imaging, the need to combine morphofunctional information can be approached by either acquiring images at different times (asynchronous), and fused them through digital image manipulation techniques or simultaneously acquiring images (synchronous) and merging them automatically. The asynchronous post-processing solution presents various constraints, mainly conditioned by the different positioning of the patient in the two scans acquired at different times in separated machines. The best solution to achieve consistency in time and space is obtained by the synchronous image acquisition. There are many multimodal technologies in molecular imaging. In this review we will focus on those multimodality image techniques more commonly used in the field of diagnostic imaging (SPECT-CT, PET-CT) and new developments (as PET-MR). The technological innovations and development of new tracers and smart probes are the main key points that will condition multimodality image and diagnostic imaging professionals' future. Although SPECT-CT and PET-CT are standard in most clinical scenarios, MR imaging has some advantages, providing excellent soft-tissue contrast and multidimensional functional, structural and morphological information. The next frontier is to develop efficient detectors and electronics systems capable of detecting two modality signals at the same time. Not only PET-MR but also MR-US or optic-PET will be introduced in clinical scenarios. Even more, MR diffusion-weighted, pharmacokinetic imaging, spectroscopy or functional BOLD imaging will merge with PET tracers to further increase molecular imaging as a relevant medical discipline. Multimodality imaging techniques will play a leading role in relevant clinical applications. The development of new diagnostic imaging research areas, mainly in the field of oncology, cardiology and neuropsychiatry, will impact the way medicine is performed today. Both clinical and experimental multimodality studies, in

Portable Imaging Polarimeter and Imaging Experiments; TOPICAL

International Nuclear Information System (INIS)

PHIPPS, GARY S.; KEMME, SHANALYN A.; SWEATT, WILLIAM C.; DESCOUR, M.R.; GARCIA, J.P.; DERENIAK, E.L.

1999-01-01

Polarimetry is the method of recording the state of polarization of light. Imaging polarimetry extends this method to recording the spatially resolved state of polarization within a scene. Imaging-polarimetry data have the potential to improve the detection of manmade objects in natural backgrounds. We have constructed a midwave infrared complete imaging polarimeter consisting of a fixed wire-grid polarizer and rotating form-birefringent retarder. The retardance and the orientation angles of the retarder were optimized to minimize the sensitivity of the instrument to noise in the measurements. The optimal retardance was found to be 132(degree) rather than the typical 90(degree). The complete imaging polarimeter utilized a liquid-nitrogen cooled PtSi camera. The fixed wire-grid polarizer was located at the cold stop inside the camera dewar. The complete imaging polarimeter was operated in the 4.42-5(micro)m spectral range. A series of imaging experiments was performed using as targets a surface of water, an automobile, and an aircraft. Further analysis of the polarization measurements revealed that in all three cases the magnitude of circular polarization was comparable to the noise in the calculated Stokes-vector components

Quantitative perfusion imaging in magnetic resonance imaging

International Nuclear Information System (INIS)

Zoellner, F.G.; Gaa, T.; Zimmer, F.; Ong, M.M.; Riffel, P.; Hausmann, D.; Schoenberg, S.O.; Weis, M.

2016-01-01

Magnetic resonance imaging (MRI) is recognized for its superior tissue contrast while being non-invasive and free of ionizing radiation. Due to the development of new scanner hardware and fast imaging techniques during the last decades, access to tissue and organ functions became possible. One of these functional imaging techniques is perfusion imaging with which tissue perfusion and capillary permeability can be determined from dynamic imaging data. Perfusion imaging by MRI can be performed by two approaches, arterial spin labeling (ASL) and dynamic contrast-enhanced (DCE) MRI. While the first method uses magnetically labelled water protons in arterial blood as an endogenous tracer, the latter involves the injection of a contrast agent, usually gadolinium (Gd), as a tracer for calculating hemodynamic parameters. Studies have demonstrated the potential of perfusion MRI for diagnostics and also for therapy monitoring. The utilization and application of perfusion MRI are still restricted to specialized centers, such as university hospitals. A broad application of the technique has not yet been implemented. The MRI perfusion technique is a valuable tool that might come broadly available after implementation of standards on European and international levels. Such efforts are being promoted by the respective professional bodies. (orig.) [de

Image Quality in High-resolution and High-cadence Solar Imaging

Science.gov (United States)

Denker, C.; Dineva, E.; Balthasar, H.; Verma, M.; Kuckein, C.; Diercke, A.; González Manrique, S. J.

2018-03-01

Broad-band imaging and even imaging with a moderate bandpass (about 1 nm) provides a photon-rich environment, where frame selection (lucky imaging) becomes a helpful tool in image restoration, allowing us to perform a cost-benefit analysis on how to design observing sequences for imaging with high spatial resolution in combination with real-time correction provided by an adaptive optics (AO) system. This study presents high-cadence (160 Hz) G-band and blue continuum image sequences obtained with the High-resolution Fast Imager (HiFI) at the 1.5-meter GREGOR solar telescope, where the speckle-masking technique is used to restore images with nearly diffraction-limited resolution. The HiFI employs two synchronized large-format and high-cadence sCMOS detectors. The median filter gradient similarity (MFGS) image-quality metric is applied, among others, to AO-corrected image sequences of a pore and a small sunspot observed on 2017 June 4 and 5. A small region of interest, which was selected for fast-imaging performance, covered these contrast-rich features and their neighborhood, which were part of Active Region NOAA 12661. Modifications of the MFGS algorithm uncover the field- and structure-dependency of this image-quality metric. However, MFGS still remains a good choice for determining image quality without a priori knowledge, which is an important characteristic when classifying the huge number of high-resolution images contained in data archives. In addition, this investigation demonstrates that a fast cadence and millisecond exposure times are still insufficient to reach the coherence time of daytime seeing. Nonetheless, the analysis shows that data acquisition rates exceeding 50 Hz are required to capture a substantial fraction of the best seeing moments, significantly boosting the performance of post-facto image restoration.

Magnetic resonance imaging

International Nuclear Information System (INIS)

Murphy, W.A.

1988-01-01

After only a few years, MR imaging has proved to be an important method for imaging disorders of the musculoskeletal tissues. The images are characterized by great inherent contrast, excellent spatial resolution, and exquisite anatomic display - major reasons why MR imaging compares favorably with other imaging methods, such as radionuclide bone scanning and CT. MR imaging is particularly sensitive to bone marrow alterations and is very effective for detection and characterization of a wide variety of soft tissue conditions. Advances in surface coil technology will increase the usefulness of MR imaging in the evaluation of articular disease. In addition, chemical shift imaging and spectroscopy will add physiologic information to the anatomic features demonstrated by proton imaging

Optoelectronic imaging of speckle using image processing method

Science.gov (United States)

Wang, Jinjiang; Wang, Pengfei

2018-01-01

A detailed image processing of laser speckle interferometry is proposed as an example for the course of postgraduate student. Several image processing methods were used together for dealing with optoelectronic imaging system, such as the partial differential equations (PDEs) are used to reduce the effect of noise, the thresholding segmentation also based on heat equation with PDEs, the central line is extracted based on image skeleton, and the branch is removed automatically, the phase level is calculated by spline interpolation method, and the fringe phase can be unwrapped. Finally, the imaging processing method was used to automatically measure the bubble in rubber with negative pressure which could be used in the tire detection.

Review methods for image segmentation from computed tomography images

International Nuclear Information System (INIS)

Mamat, Nurwahidah; Rahman, Wan Eny Zarina Wan Abdul; Soh, Shaharuddin Cik; Mahmud, Rozi

2014-01-01

Image segmentation is a challenging process in order to get the accuracy of segmentation, automation and robustness especially in medical images. There exist many segmentation methods that can be implemented to medical images but not all methods are suitable. For the medical purposes, the aims of image segmentation are to study the anatomical structure, identify the region of interest, measure tissue volume to measure growth of tumor and help in treatment planning prior to radiation therapy. In this paper, we present a review method for segmentation purposes using Computed Tomography (CT) images. CT images has their own characteristics that affect the ability to visualize anatomic structures and pathologic features such as blurring of the image and visual noise. The details about the methods, the goodness and the problem incurred in the methods will be defined and explained. It is necessary to know the suitable segmentation method in order to get accurate segmentation. This paper can be a guide to researcher to choose the suitable segmentation method especially in segmenting the images from CT scan

First Human Experience with Directly Image-able Iodinated Embolization Microbeads

Energy Technology Data Exchange (ETDEWEB)

Levy, Elliot B., E-mail: levyeb@cc.nih.gov; Krishnasamy, Venkatesh P. [National Institutes of Health, Center for Interventional Oncology (United States); Lewis, Andrew L.; Willis, Sean; Macfarlane, Chelsea [Biocompatibles, UK Ltd, A BTG International Group Company (United Kingdom); Anderson, Victoria [National Institutes of Health, Center for Interventional Oncology (United States); Bom, Imramsjah MJ van der [Clinical Science IGT Systems North & Latin America, Philips, Philips, Image Guided Interventions (United States); Radaelli, Alessandro [Image-Guided Therapy Systems, Philips, Philips, Image Guided Interventions (Netherlands); Dreher, Matthew R. [Biocompatibles, UK Ltd, A BTG International Group Company (United Kingdom); Sharma, Karun V. [Children’s National Medical Center (United States); Negussie, Ayele; Mikhail, Andrew S. [National Institutes of Health, Center for Interventional Oncology (United States); Geschwind, Jean-Francois H. [Department of Radiology and Biomedical Imaging (United States); Wood, Bradford J. [National Institutes of Health, Center for Interventional Oncology (United States)

2016-08-15

PurposeTo describe first clinical experience with a directly image-able, inherently radio-opaque microspherical embolic agent for transarterial embolization of liver tumors.MethodologyLC Bead LUMI™ is a new product based upon sulfonate-modified polyvinyl alcohol hydrogel microbeads with covalently bound iodine (~260 mg I/ml). 70–150 μ LC Bead LUMI™ iodinated microbeads were injected selectively via a 2.8 Fr microcatheter to near complete flow stasis into hepatic arteries in three patients with hepatocellular carcinoma, carcinoid, or neuroendocrine tumor. A custom imaging platform tuned for LC LUMI™ microbead conspicuity using a cone beam CT (CBCT)/angiographic C-arm system (Allura Clarity FD20, Philips) was used along with CBCT embolization treatment planning software (EmboGuide, Philips).ResultsLC Bead LUMI™ image-able microbeads were easily delivered and monitored during the procedure using fluoroscopy, single-shot radiography (SSD), digital subtraction angiography (DSA), dual-phase enhanced and unenhanced CBCT, and unenhanced conventional CT obtained 48 h after the procedure. Intra-procedural imaging demonstrated tumor at risk for potential under-treatment, defined as paucity of image-able microbeads within a portion of the tumor which was confirmed at 48 h CT imaging. Fusion of pre- and post-embolization CBCT identified vessels without beads that corresponded to enhancing tumor tissue in the same location on follow-up imaging (48 h post).ConclusionLC Bead LUMI™ image-able microbeads provide real-time feedback and geographic localization of treatment in real time during treatment. The distribution and density of image-able beads within a tumor need further evaluation as an additional endpoint for embolization.

Application of image editing software for forensic detection of image ...

African Journals Online (AJOL)

Application of image editing software for forensic detection of image. ... The image editing software's available today is apt for creating visually compelling and sophisticated fake images, ... EMAIL FREE FULL TEXT EMAIL FREE FULL TEXT

BMC ecology image competition 2017: the winning images.

Science.gov (United States)

Foote, Christopher; Darimont, Chris T; Baguette, Michel; Blanchet, Simon; Jacobus, Luke M; Mazzi, Dominique; Settele, Josef

2017-08-18

For the fifth year, BMC Ecology is proud to present the winning images from our annual image competition. The 2017 edition received entries by talented shutterbug-ecologists from across the world, showcasing research that is increasing our understanding of ecosystems worldwide and the beauty and diversity of life on our planet. In this editorial we showcase the winning images, as chosen by our Editorial Board and guest judge Chris Darimont, as well as our selection of highly commended images. Enjoy!

Microscopic validation of whole mouse micro-metastatic tumor imaging agents using cryo-imaging and sliding organ image registration

OpenAIRE

Liu, Yiqiao; Zhou, Bo; Qutaish, Mohammed; Wilson, David L.

2016-01-01

We created a metastasis imaging, analysis platform consisting of software and multi-spectral cryo-imaging system suitable for evaluating emerging imaging agents targeting micro-metastatic tumor. We analyzed CREKA-Gd in MRI, followed by cryo-imaging which repeatedly sectioned and tiled microscope images of the tissue block face, providing anatomical bright field and molecular fluorescence, enabling 3D microscopic imaging of the entire mouse with single metastatic cell sensitivity. To register ...

Data imaging

International Nuclear Information System (INIS)

Pepy, G.

1999-01-01

After an introduction about data imaging in general, the principles of imaging data collected via neutron scattering experiments are presented. Some computer programs designed for data imaging purposes are reviewed. (K.A.)

Cerenkov imaging.

Science.gov (United States)

Das, Sudeep; Thorek, Daniel L J; Grimm, Jan

2014-01-01

Cerenkov luminescence (CL) has been used recently in a plethora of medical applications like imaging and therapy with clinically relevant medical isotopes. The range of medical isotopes used is fairly large and expanding. The generation of in vivo light is useful since it circumvents depth limitations for excitation light. Cerenkov luminescence imaging (CLI) is much cheaper in terms of infrastructure than positron emission tomography (PET) and is particularly useful for imaging of superficial structures. Imaging can basically be done using a sensitive camera optimized for low-light conditions, and it has a better resolution than any other nuclear imaging modality. CLI has been shown to effectively diagnose disease with regularly used PET isotope ((18)F-FDG) in clinical setting. Cerenkov luminescence tomography, Cerenkov luminescence endoscopy, and intraoperative Cerenkov imaging have also been explored with positive conclusions expanding the current range of applications. Cerenkov has also been used to improve PET imaging resolution since the source of both is the radioisotope being used. Smart imaging agents have been designed based on modulation of the Cerenkov signal using small molecules and nanoparticles giving better insight of the tumor biology. © 2014 Elsevier Inc. All rights reserved.

Imaging Human Brain Perfusion with Inhaled Hyperpolarized 129Xe MR Imaging.

Science.gov (United States)

Rao, Madhwesha R; Stewart, Neil J; Griffiths, Paul D; Norquay, Graham; Wild, Jim M

2018-02-01

Purpose To evaluate the feasibility of directly imaging perfusion of human brain tissue by using magnetic resonance (MR) imaging with inhaled hyperpolarized xenon 129 ( 129 Xe). Materials and Methods In vivo imaging with 129 Xe was performed in three healthy participants. The combination of a high-yield spin-exchange optical pumping 129 Xe polarizer, custom-built radiofrequency coils, and an optimized gradient-echo MR imaging protocol was used to achieve signal sensitivity sufficient to directly image hyperpolarized 129 Xe dissolved in the human brain. Conventional T1-weighted proton (hydrogen 1 [ 1 H]) images and perfusion images by using arterial spin labeling were obtained for comparison. Results Images of 129 Xe uptake were obtained with a signal-to-noise ratio of 31 ± 9 and demonstrated structural similarities to the gray matter distribution on conventional T1-weighted 1 H images and to perfusion images from arterial spin labeling. Conclusion Hyperpolarized 129 Xe MR imaging is an injection-free means of imaging the perfusion of cerebral tissue. The proposed method images the uptake of inhaled xenon gas to the extravascular brain tissue compartment across the intact blood-brain barrier. This level of sensitivity is not readily available with contemporary MR imaging methods. © RSNA, 2017.

Distance between images

Science.gov (United States)

Gualtieri, J. A.; Le Moigne, J.; Packer, C. V.

1992-01-01

Comparing two binary images and assigning a quantitative measure to this comparison finds its purpose in such tasks as image recognition, image compression, and image browsing. This quantitative measurement may be computed by utilizing the Hausdorff distance of the images represented as two-dimensional point sets. In this paper, we review two algorithms that have been proposed to compute this distance, and we present a parallel implementation of one of them on the MasPar parallel processor. We study their complexity and the results obtained by these algorithms for two different types of images: a set of displaced pairs of images of Gaussian densities, and a comparison of a Canny edge image with several edge images from a hierarchical region growing code.

Radiological Image Compression

Science.gov (United States)

Lo, Shih-Chung Benedict

The movement toward digital images in radiology presents the problem of how to conveniently and economically store, retrieve, and transmit the volume of digital images. Basic research into image data compression is necessary in order to move from a film-based department to an efficient digital -based department. Digital data compression technology consists of two types of compression technique: error-free and irreversible. Error -free image compression is desired; however, present techniques can only achieve compression ratio of from 1.5:1 to 3:1, depending upon the image characteristics. Irreversible image compression can achieve a much higher compression ratio; however, the image reconstructed from the compressed data shows some difference from the original image. This dissertation studies both error-free and irreversible image compression techniques. In particular, some modified error-free techniques have been tested and the recommended strategies for various radiological images are discussed. A full-frame bit-allocation irreversible compression technique has been derived. A total of 76 images which include CT head and body, and radiographs digitized to 2048 x 2048, 1024 x 1024, and 512 x 512 have been used to test this algorithm. The normalized mean -square-error (NMSE) on the difference image, defined as the difference between the original and the reconstructed image from a given compression ratio, is used as a global measurement on the quality of the reconstructed image. The NMSE's of total of 380 reconstructed and 380 difference images are measured and the results tabulated. Three complex compression methods are also suggested to compress images with special characteristics. Finally, various parameters which would effect the quality of the reconstructed images are discussed. A proposed hardware compression module is given in the last chapter.

A proteção social no Brasil: universalismo e focalização nos governos FHC e Lula Social protection in Brazil: universalism and targeting in the FHC and Lula administrations

Directory of Open Access Journals (Sweden)

Nilson do Rosário Costa

2009-06-01

Full Text Available O artigo analisa a configuração do sistema de proteção social no Brasil após a Constituição Federal de 1988 (CF 1988. Demonstra que a CF 1988 favoreceu a institucionalização de políticas públicas universalistas. Esta institucionalização foi realizada em conflito com os pressupostos da estabilização do Plano Real. O trabalho argumenta que a institucionalização protegeu o gasto público na área social da proposta minimalista da gestão macroeconômica. Identifica também a implementação de programas sociais focalizados nos pobres ao longo da década de 1990. A focalização é uma inovação diretamente associada à agenda do ajuste. Revela que nos governo FHC e Lula ocorreu uma idêntica adesão aos programas sociais focalizados. A focalização da proteção social não teve o poder de vetar as propostas universalistas originadas da democratização dos anos 1980. Demonstra que o Programa Bolsa Família (PBF, principal marca do governo Lula, é uma adaptação, em larga escala, dos programas focalizados de transferência direta de renda do período FHC. A combinação de universalismo e focalização ampliou o escopo da política social. O expressivo crescimento do gasto público social não tem, entretanto, produzido resultados sociais abrangente, ainda que os pobres no Brasil tenham sido beneficiados pela focalização do PBF.This article analyzes the organization of Brazil's social protection system after the Federal Constitution of 1998 (CF 1988. It also demonstrates that 1988 Federal Constitution favored the institutionalization of universalist public policies. This institutionalization took place amidst conflict with the stabilization goals of the Real Plan. The paper argues that such an institutionalization protected public spending in the social area of the macroeconomic management's minimalist project. It also identifies the implementation of social programs targeting the poor during the 1980's decade. Targeting is

Acoustical holographic Siamese image technique for imaging radial cracks in reactor piping

International Nuclear Information System (INIS)

Collins, H.D.; Gribble, R.P.

1985-04-01

This paper describes a unique technique (i.e., ''Siamese imaging'') for imaging quasi-vertical defects in reactor pipe weldments. The Siamese image is a bi-symmetrical view of the inner surface defect. Image construction geometry consists of two probes (i.e., source/receiver) operating either from opposite sides or the same side of the defect to be imaged. As the probes are scanned across a lower surface connected defect, they encounter two images - first the normal upright image and then the inverted image. The final integrated image consists of two images connected along their baselines, thus we call it a ''Siamese image.'' The experimental imaging results on simulated and natural cracks in reactor piping weldments graphically illustrate this unique technique. Excellent images of mechanical fatique and thermal cracks were obtained on ferritic and austenitic piping